Observer performance assessment of JPEG-compressed high-resolution chest images

NASA Astrophysics Data System (ADS)

Good, Walter F.; Maitz, Glenn S.; King, Jill L.; Gennari, Rose C.; Gur, David

1999-05-01

The JPEG compression algorithm was tested on a set of 529 chest radiographs that had been digitized at a spatial resolution of 100 micrometer and contrast sensitivity of 12 bits. Images were compressed using five fixed 'psychovisual' quantization tables which produced average compression ratios in the range 15:1 to 61:1, and were then printed onto film. Six experienced radiologists read all cases from the laser printed film, in each of the five compressed modes as well as in the non-compressed mode. For comparison purposes, observers also read the same cases with reduced pixel resolutions of 200 micrometer and 400 micrometer. The specific task involved detecting masses, pneumothoraces, interstitial disease, alveolar infiltrates and rib fractures. Over the range of compression ratios tested, for images digitized at 100 micrometer, we were unable to demonstrate any statistically significant decrease (p greater than 0.05) in observer performance as measured by ROC techniques. However, the observers' subjective assessments of image quality did decrease significantly as image resolution was reduced and suggested a decreasing, but nonsignificant, trend as the compression ratio was increased. The seeming discrepancy between our failure to detect a reduction in observer performance, and other published studies, is likely due to: (1) the higher resolution at which we digitized our images; (2) the higher signal-to-noise ratio of our digitized films versus typical CR images; and (3) our particular choice of an optimized quantization scheme.

An Ultra-Low Power Turning Angle Based Biomedical Signal Compression Engine with Adaptive Threshold Tuning

PubMed Central

Zhou, Jun; Wang, Chao

2017-01-01

Intelligent sensing is drastically changing our everyday life including healthcare by biomedical signal monitoring, collection, and analytics. However, long-term healthcare monitoring generates tremendous data volume and demands significant wireless transmission power, which imposes a big challenge for wearable healthcare sensors usually powered by batteries. Efficient compression engine design to reduce wireless transmission data rate with ultra-low power consumption is essential for wearable miniaturized healthcare sensor systems. This paper presents an ultra-low power biomedical signal compression engine for healthcare data sensing and analytics in the era of big data and sensor intelligence. It extracts the feature points of the biomedical signal by window-based turning angle detection. The proposed approach has low complexity and thus low power consumption while achieving a large compression ratio (CR) and good quality of reconstructed signal. Near-threshold design technique is adopted to further reduce the power consumption on the circuit level. Besides, the angle threshold for compression can be adaptively tuned according to the error between the original signal and reconstructed signal to address the variation of signal characteristics from person to person or from channel to channel to meet the required signal quality with optimal CR. For demonstration, the proposed biomedical compression engine has been used and evaluated for ECG compression. It achieves an average (CR) of 71.08% and percentage root-mean-square difference (PRD) of 5.87% while consuming only 39 nW. Compared to several state-of-the-art ECG compression engines, the proposed design has significantly lower power consumption while achieving similar CRD and PRD, making it suitable for long-term wearable miniaturized sensor systems to sense and collect healthcare data for remote data analytics. PMID:28783079

An Ultra-Low Power Turning Angle Based Biomedical Signal Compression Engine with Adaptive Threshold Tuning.

PubMed

Zhou, Jun; Wang, Chao

2017-08-06

Intelligent sensing is drastically changing our everyday life including healthcare by biomedical signal monitoring, collection, and analytics. However, long-term healthcare monitoring generates tremendous data volume and demands significant wireless transmission power, which imposes a big challenge for wearable healthcare sensors usually powered by batteries. Efficient compression engine design to reduce wireless transmission data rate with ultra-low power consumption is essential for wearable miniaturized healthcare sensor systems. This paper presents an ultra-low power biomedical signal compression engine for healthcare data sensing and analytics in the era of big data and sensor intelligence. It extracts the feature points of the biomedical signal by window-based turning angle detection. The proposed approach has low complexity and thus low power consumption while achieving a large compression ratio (CR) and good quality of reconstructed signal. Near-threshold design technique is adopted to further reduce the power consumption on the circuit level. Besides, the angle threshold for compression can be adaptively tuned according to the error between the original signal and reconstructed signal to address the variation of signal characteristics from person to person or from channel to channel to meet the required signal quality with optimal CR. For demonstration, the proposed biomedical compression engine has been used and evaluated for ECG compression. It achieves an average (CR) of 71.08% and percentage root-mean-square difference (PRD) of 5.87% while consuming only 39 nW. Compared to several state-of-the-art ECG compression engines, the proposed design has significantly lower power consumption while achieving similar CRD and PRD, making it suitable for long-term wearable miniaturized sensor systems to sense and collect healthcare data for remote data analytics.

Effect of data compression on diagnostic accuracy in digital hand and chest radiography

NASA Astrophysics Data System (ADS)

Sayre, James W.; Aberle, Denise R.; Boechat, Maria I.; Hall, Theodore R.; Huang, H. K.; Ho, Bruce K. T.; Kashfian, Payam; Rahbar, Guita

1992-05-01

Image compression is essential to handle a large volume of digital images including CT, MR, CR, and digitized films in a digital radiology operation. The full-frame bit allocation using the cosine transform technique developed during the last few years has been proven to be an excellent irreversible image compression method. This paper describes the effect of using the hardware compression module on diagnostic accuracy in hand radiographs with subperiosteal resorption and chest radiographs with interstitial disease. Receiver operating characteristic analysis using 71 hand radiographs and 52 chest radiographs with five observers each demonstrates that there is no statistical significant difference in diagnostic accuracy between the original films and the compressed images with a compression ratio as high as 20:1.

Accelerated Echo Planer J-resolved Spectroscopic Imaging of Putamen and Thalamus in Obstructive Sleep Apnea.

PubMed

Sarma, Manoj K; Macey, Paul M; Nagarajan, Rajakumar; Aysola, Ravi; Harper, Ronald M; Thomas, M Albert

2016-09-06

Obstructive sleep apnea syndrome (OSAS) leads to neurocognitive and autonomic deficits that are partially mediated by thalamic and putamen pathology. We examined the underlying neurochemistry of those structures using compressed sensing-based 4D echo-planar J-resolved spectroscopic imaging (JRESI), and quantified values with prior knowledge fitting. Bilaterally increased thalamic mI/Cr, putamen Glx/Cr, and Glu/Cr, and bilaterally decreased thalamic and putamen tCho/Cr and GABA/Cr occurred in OSAS vs healthy subjects (p < 0.05). Increased right thalamic Glx/Cr, Glu/Cr, Gln/Cr, Asc/Cr, and decreased GPC/Cr and decreased left thalamic tNAA/Cr, NAA/Cr were detected. The right putamen showed increased mI/Cr and decreased tCho/Cr, and the left, decreased PE/Cr ratio. ROC curve analyses demonstrated 60-100% sensitivity and specificity for the metabolite ratios in differentiating OSAS vs. Positive correlations were found between: left thalamus mI/Cr and baseline oxygen saturation (SaO2); right putamen tCho/Cr and apnea hypopnea index; right putamen GABA/Cr and baseline SaO2; left putamen PE/Cr and baseline SaO2; and left putamen NAA/Cr and SaO2 nadir (all p < 0.05). Negative correlations were found between left putamen PE/Cr and SaO2 nadir. These findings suggest underlying inflammation or glial activation, with greater alterations accompanying lower oxygen saturation. These metabolite levels may provide biomarkers for future neurochemical interventions by pharmacologic or other means.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends.

PubMed

Ahmed, Khalil

2015-11-01

Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE) compatibilized by Chloroprene rubber (CR) were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr) was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (M L) and maximum torque (M H) of blends increased with increasing weight ratio of HDPE while scorch time (ts2) cure time (tc90), compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties.

An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends

PubMed Central

Ahmed, Khalil

2014-01-01

Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE) compatibilized by Chloroprene rubber (CR) were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr) was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (ML) and maximum torque (MH) of blends increased with increasing weight ratio of HDPE while scorch time (ts2) cure time (tc90), compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties. PMID:26644917

Improving Remote Health Monitoring: A Low-Complexity ECG Compression Approach

PubMed Central

Al-Ali, Abdulla; Mohamed, Amr; Ward, Rabab

2018-01-01

Recent advances in mobile technology have created a shift towards using battery-driven devices in remote monitoring settings and smart homes. Clinicians are carrying out diagnostic and screening procedures based on the electrocardiogram (ECG) signals collected remotely for outpatients who need continuous monitoring. High-speed transmission and analysis of large recorded ECG signals are essential, especially with the increased use of battery-powered devices. Exploring low-power alternative compression methodologies that have high efficiency and that enable ECG signal collection, transmission, and analysis in a smart home or remote location is required. Compression algorithms based on adaptive linear predictors and decimation by a factor B/K are evaluated based on compression ratio (CR), percentage root-mean-square difference (PRD), and heartbeat detection accuracy of the reconstructed ECG signal. With two databases (153 subjects), the new algorithm demonstrates the highest compression performance (CR=6 and PRD=1.88) and overall detection accuracy (99.90% sensitivity, 99.56% positive predictivity) over both databases. The proposed algorithm presents an advantage for the real-time transmission of ECG signals using a faster and more efficient method, which meets the growing demand for more efficient remote health monitoring. PMID:29337892

Improving Remote Health Monitoring: A Low-Complexity ECG Compression Approach.

PubMed

Elgendi, Mohamed; Al-Ali, Abdulla; Mohamed, Amr; Ward, Rabab

2018-01-16

Recent advances in mobile technology have created a shift towards using battery-driven devices in remote monitoring settings and smart homes. Clinicians are carrying out diagnostic and screening procedures based on the electrocardiogram (ECG) signals collected remotely for outpatients who need continuous monitoring. High-speed transmission and analysis of large recorded ECG signals are essential, especially with the increased use of battery-powered devices. Exploring low-power alternative compression methodologies that have high efficiency and that enable ECG signal collection, transmission, and analysis in a smart home or remote location is required. Compression algorithms based on adaptive linear predictors and decimation by a factor B / K are evaluated based on compression ratio (CR), percentage root-mean-square difference (PRD), and heartbeat detection accuracy of the reconstructed ECG signal. With two databases (153 subjects), the new algorithm demonstrates the highest compression performance ( CR = 6 and PRD = 1.88 ) and overall detection accuracy (99.90% sensitivity, 99.56% positive predictivity) over both databases. The proposed algorithm presents an advantage for the real-time transmission of ECG signals using a faster and more efficient method, which meets the growing demand for more efficient remote health monitoring.

Nonlinear frequency compression: Influence of start frequency and input bandwidth on consonant and vowel recognitiona)

PubMed Central

Alexander, Joshua M.

2016-01-01

By varying parameters that control nonlinear frequency compression (NFC), this study examined how different ways of compressing inaudible mid- and/or high-frequency information at lower frequencies influences perception of consonants and vowels. Twenty-eight listeners with mild to moderately severe hearing loss identified consonants and vowels from nonsense syllables in noise following amplification via a hearing aid simulator. Low-pass filtering and the selection of NFC parameters fixed the output bandwidth at a frequency representing a moderately severe (3.3 kHz, group MS) or a mild-to-moderate (5.0 kHz, group MM) high-frequency loss. For each group (n = 14), effects of six combinations of NFC start frequency (SF) and input bandwidth [by varying the compression ratio (CR)] were examined. For both groups, the 1.6 kHz SF significantly reduced vowel and consonant recognition, especially as CR increased; whereas, recognition was generally unaffected if SF increased at the expense of a higher CR. Vowel recognition detriments for group MS were moderately correlated with the size of the second formant frequency shift following NFC. For both groups, significant improvement (33%–50%) with NFC was confined to final /s/ and /z/ and to some VCV tokens, perhaps because of listeners' limited exposure to each setting. No set of parameters simultaneously maximized recognition across all tokens. PMID:26936574

Correlation of radiologists' image quality perception with quantitative assessment parameters: just-noticeable difference vs. peak signal-to-noise ratios

NASA Astrophysics Data System (ADS)

Siddiqui, Khan M.; Siegel, Eliot L.; Reiner, Bruce I.; Johnson, Jeffrey P.

2005-04-01

The authors identify a fundamental disconnect between the ways in which industry and radiologists assess and even discuss product performance. What is needed is a quantitative methodology that can assess both subjective image quality and observer task performance. In this study, we propose and evaluate the use of a visual discrimination model (VDM) that assesses just-noticeable differences (JNDs) to serve this purpose. The study compares radiologists' subjective perceptions of image quality of computer tomography (CT) and computed radiography (CR) images with quantitative measures of peak signal-to-noise ratio (PSNR) and JNDs as measured by a VDM. The study included 4 CT and 6 CR studies with compression ratios ranging from lossless to 90:1 (total of 80 sets of images were generated [n = 1,200]). Eleven radiologists reviewed the images and rated them in terms of overall quality and readability and identified images not acceptable for interpretation. Normalized reader scores were correlated with compression, objective PSNR, and mean JND values. Results indicated a significantly higher correlation between observer performance and JND values than with PSNR methods. These results support the use of the VDM as a metric not only for the threshold discriminations for which it was calibrated, but also as a general image quality metric. This VDM is a highly promising, reproducible, and reliable adjunct or even alternative to human observer studies for research or to establish clinical guidelines for image compression, dose reductions, and evaluation of various display technologies.

Anomalous anisotropic compression behavior of superconducting CrAs under high pressure

PubMed Central

Yu, Zhenhai; Wu, Wei; Hu, Qingyang; Zhao, Jinggeng; Li, Chunyu; Yang, Ke; Cheng, Jinguang; Luo, Jianlin; Wang, Lin; Mao, Ho-kwang

2015-01-01

CrAs was observed to possess the bulk superconductivity under high-pressure conditions. To understand the superconducting mechanism and explore the correlation between the structure and superconductivity, the high-pressure structural evolution of CrAs was investigated using the angle-dispersive X-ray diffraction (XRD) method. The structure of CrAs remains stable up to 1.8 GPa, whereas the lattice parameters exhibit anomalous compression behaviors. With increasing pressure, the lattice parameters a and c both demonstrate a nonmonotonic change, and the lattice parameter b undergoes a rapid contraction at ∼0.18−0.35 GPa, which suggests that a pressure-induced isostructural phase transition occurs in CrAs. Above the phase transition pressure, the axial compressibilities of CrAs present remarkable anisotropy. A schematic band model was used to address the anomalous compression behavior of CrAs. The present results shed light on the structural and related electronic responses to high pressure, which play a key role toward understanding the superconductivity of CrAs. PMID:26627230

Assessment of low-contrast detectability for compressed digital chest images

NASA Astrophysics Data System (ADS)

Cook, Larry T.; Insana, Michael F.; McFadden, Michael A.; Hall, Timothy J.; Cox, Glendon G.

1994-04-01

The ability of human observers to detect low-contrast targets in screen-film (SF) images, computed radiographic (CR) images, and compressed CR images was measured using contrast detail (CD) analysis. The results of these studies were used to design a two- alternative forced-choice (2AFC) experiment to investigate the detectability of nodules in adult chest radiographs. CD curves for a common screen-film system were compared with CR images compressed up to 125:1. Data from clinical chest exams were used to define a CD region of clinical interest that sufficiently challenged the observer. From that data, simulated lesions were introduced into 100 normal CR chest films, and forced-choice observer performance studies were performed. CR images were compressed using a full-frame discrete cosine transform (FDCT) technique, where the 2D Fourier space was divided into four areas of different quantization depending on the cumulative power spectrum (energy) of each image. The characteristic curve of the CR images was adjusted so that optical densities matched those of the SF system. The CD curves for SF and uncompressed CR systems were statistically equivalent. The slope of the CD curve for each was - 1.0 as predicted by the Rose model. There was a significant degradation in detection found for CR images compressed to 125:1. Furthermore, contrast-detail analysis demonstrated that many pulmonary nodules encountered in clinical practice are significantly above the average observer threshold for detection. We designed a 2AFC observer study using simulated 1-cm lesions introduced into normal CR chest radiographs. Detectability was reduced for all compressed CR radiographs.

Characterization of the mechanical and physical properties of TD-NiCr (Ni-20Cr-2ThO2) alloy sheet

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.; Taylor, R. E.

1973-01-01

Sheets of TD-NiCr processed using techniques developed to produce uniform material were tested to supply mechanical and physical property data. Two heats each of 0.025 and 0.051 cm thick sheet were tested. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, compression, creep-rupture, creep strength, bearing strength, shear strength, sharp notch and fatigue strength. Test temperatures covered the range from ambient to 1589K. Physical properties were also studied as a function of temperature. The physical properties measured were thermal conductivity, linear thermal expansion, specific heat, total hemispherical emittance, thermal diffusivity, and electrical conductivity.

Color image lossy compression based on blind evaluation and prediction of noise characteristics

NASA Astrophysics Data System (ADS)

Ponomarenko, Nikolay N.; Lukin, Vladimir V.; Egiazarian, Karen O.; Lepisto, Leena

2011-03-01

The paper deals with JPEG adaptive lossy compression of color images formed by digital cameras. Adaptation to noise characteristics and blur estimated for each given image is carried out. The dominant factor degrading image quality is determined in a blind manner. Characteristics of this dominant factor are then estimated. Finally, a scaling factor that determines quantization steps for default JPEG table is adaptively set (selected). Within this general framework, two possible strategies are considered. A first one presumes blind estimation for an image after all operations in digital image processing chain just before compressing a given raster image. A second strategy is based on prediction of noise and blur parameters from analysis of RAW image under quite general assumptions concerning characteristics parameters of transformations an image will be subject to at further processing stages. The advantages of both strategies are discussed. The first strategy provides more accurate estimation and larger benefit in image compression ratio (CR) compared to super-high quality (SHQ) mode. However, it is more complicated and requires more resources. The second strategy is simpler but less beneficial. The proposed approaches are tested for quite many real life color images acquired by digital cameras and shown to provide more than two time increase of average CR compared to SHQ mode without introducing visible distortions with respect to SHQ compressed images.

Clinical evaluation of JPEG2000 compression for digital mammography

NASA Astrophysics Data System (ADS)

Sung, Min-Mo; Kim, Hee-Joung; Kim, Eun-Kyung; Kwak, Jin-Young; Yoo, Jae-Kyung; Yoo, Hyung-Sik

2002-06-01

Medical images, such as computed radiography (CR), and digital mammographic images will require large storage facilities and long transmission times for picture archiving and communications system (PACS) implementation. American College of Radiology and National Equipment Manufacturers Association (ACR/NEMA) group is planning to adopt a JPEG2000 compression algorithm in digital imaging and communications in medicine (DICOM) standard to better utilize medical images. The purpose of the study was to evaluate the compression ratios of JPEG2000 for digital mammographic images using peak signal-to-noise ratio (PSNR), receiver operating characteristic (ROC) analysis, and the t-test. The traditional statistical quality measures such as PSNR, which is a commonly used measure for the evaluation of reconstructed images, measures how the reconstructed image differs from the original by making pixel-by-pixel comparisons. The ability to accurately discriminate diseased cases from normal cases is evaluated using ROC curve analysis. ROC curves can be used to compare the diagnostic performance of two or more reconstructed images. The t test can be also used to evaluate the subjective image quality of reconstructed images. The results of the t test suggested that the possible compression ratios using JPEG2000 for digital mammographic images may be as much as 15:1 without visual loss or with preserving significant medical information at a confidence level of 99%, although both PSNR and ROC analyses suggest as much as 80:1 compression ratio can be achieved without affecting clinical diagnostic performance.

Effect of cobalt on microstructure and properties of AlCr1.5CuFeNi2Cox high-entropy alloys

NASA Astrophysics Data System (ADS)

Kukshal, Vikas; Patnaik, Amar; Bhat, I. K.

2018-04-01

The present paper investigates the effect of Co addition on the alloying behaviour, microstructure and the resulting properties of cast AlCr1.5CuFeNi2Cox high-entropy alloys intended to be used for high temperature applications. The elements Al, Cr, Cu, Fe, Ni and Co (Purity > 99) weighing approximately 800 g was melted in a high temperature vacuum induction furnace. The microstructure, phase transformation, density, microhardness and compressive strength of the samples were analysed using x-ray diffraction (XRD), scanning electron microscopes (SEM), Vickers microhardness tester and universal Testing machine. The crystalline structure of the alloys exhibits simple FCC and BCC phases. The microstructures investigation of the alloys shows the segregation of copper in the interdendritic region resulting in Cu-rich FCC phase. The addition of Co further enhances the formation of FCC phase resulting in the decrease in micro hardness value of the alloys, which varies from 471 HV to 364 HV with increase in the cobalt content from x = 0 to x = 1 (molar ratio). The similar decreasing trend is also observed for the compressive strength of the alloys.

Preparation and Physicochemical Evaluation of Controlled-release Carbon Source Tablet for Groundwater in situ Denitrification

NASA Astrophysics Data System (ADS)

Kim, Y.; Kang, J. H.; Yeum, Y.; Han, K. J.; Kim, D. W.; Park, C. W.

2015-12-01

Nitric nitrogen could be the one of typical pollution source such asNO3-through domestic sewage, livestock and agricultural wastewater. Resident microflorain aquifer has known to remove the nitric nitrogen spontaneously following the denitration process with the carbon source (CS) as reactant. However, it could be reacted very slowly with the rack of CS and there have been some studies for controlled addition of CS (Ref #1-3). The aim of this study was to prepare the controlled-release carbon source (CR-CS) tablet and to evaluate in vitro release profile for groundwater in situ denitrification. CR-CS tablet could be manufactured by direct compression method using hydraulic laboratory press (Caver® 3850) with 8 mm rounded concave punch/ die.Seven kinds of CR-CS tablet were prepared to determine the nature of the additives and their ratio such as sodium silicate, dicalcium phosphate, bentonite and sand#8.For each formulation, the LOD% and flowability of pre-mixed powders and the hardness of compressed tablets were analyzed. In vitro release study was performed to confirm the dissolution profiles following the USP Apparatus 2 method with Distilled water of 900mL, 20 °C. As a result, for each lubricated powders, they were compared in terms of ability to give an acceptable dry pre-mixed powder for tableting process. The hardness of the compressed tablets is acceptable whatever the formulations tested. After in vitro release study, it could confirm that the different formulations of CR-CS tablet have a various release rate patterns, which could release 100% at 3 hrs, 6 hrs and 12 hrs. The in vitro dissolution profiles were in good correlation of Higuchi release kinetic model. In conclusion, this study could be used as a background for development and evaluation of the controlled-release carbon source (CR-CS) tablet for the purification of groundwater following the in situ denitrification.

Numerical investigation of CAI Combustion in the Opposed- Piston Engine with Direct and Indirect Water Injection

NASA Astrophysics Data System (ADS)

Pyszczek, R.; Mazuro, P.; Teodorczyk, A.

2016-09-01

This paper is focused on the CAI combustion control in a turbocharged 2-stroke Opposed-Piston (OP) engine. The barrel type OP engine arrangement is of particular interest for the authors because of its robust design, high mechanical efficiency and relatively easy incorporation of a Variable Compression Ratio (VCR). The other advantage of such design is that combustion chamber is formed between two moving pistons - there is no additional cylinder head to be cooled which directly results in an increased thermal efficiency. Furthermore, engine operation in a Controlled Auto-Ignition (CAI) mode at high compression ratios (CR) raises a possibility of reaching even higher efficiencies and very low emissions. In order to control CAI combustion such measures as VCR and water injection were considered for indirect ignition timing control. Numerical simulations of the scavenging and combustion processes were performed with the 3D CFD multipurpose AVL Fire solver. Numerous cases were calculated with different engine compression ratios and different amounts of directly and indirectly injected water. The influence of the VCR and water injection on the ignition timing and engine performance was determined and their application in the real engine was discussed.

Comparison of two SVD-based color image compression schemes.

PubMed

Li, Ying; Wei, Musheng; Zhang, Fengxia; Zhao, Jianli

2017-01-01

Color image compression is a commonly used process to represent image data as few bits as possible, which removes redundancy in the data while maintaining an appropriate level of quality for the user. Color image compression algorithms based on quaternion are very common in recent years. In this paper, we propose a color image compression scheme, based on the real SVD, named real compression scheme. First, we form a new real rectangular matrix C according to the red, green and blue components of the original color image and perform the real SVD for C. Then we select several largest singular values and the corresponding vectors in the left and right unitary matrices to compress the color image. We compare the real compression scheme with quaternion compression scheme by performing quaternion SVD using the real structure-preserving algorithm. We compare the two schemes in terms of operation amount, assignment number, operation speed, PSNR and CR. The experimental results show that with the same numbers of selected singular values, the real compression scheme offers higher CR, much less operation time, but a little bit smaller PSNR than the quaternion compression scheme. When these two schemes have the same CR, the real compression scheme shows more prominent advantages both on the operation time and PSNR.

Comparison of two SVD-based color image compression schemes

PubMed Central

Li, Ying; Wei, Musheng; Zhang, Fengxia; Zhao, Jianli

2017-01-01

Color image compression is a commonly used process to represent image data as few bits as possible, which removes redundancy in the data while maintaining an appropriate level of quality for the user. Color image compression algorithms based on quaternion are very common in recent years. In this paper, we propose a color image compression scheme, based on the real SVD, named real compression scheme. First, we form a new real rectangular matrix C according to the red, green and blue components of the original color image and perform the real SVD for C. Then we select several largest singular values and the corresponding vectors in the left and right unitary matrices to compress the color image. We compare the real compression scheme with quaternion compression scheme by performing quaternion SVD using the real structure-preserving algorithm. We compare the two schemes in terms of operation amount, assignment number, operation speed, PSNR and CR. The experimental results show that with the same numbers of selected singular values, the real compression scheme offers higher CR, much less operation time, but a little bit smaller PSNR than the quaternion compression scheme. When these two schemes have the same CR, the real compression scheme shows more prominent advantages both on the operation time and PSNR. PMID:28257451

Development of a Natural Gas-Powered APU for a Hybrid Electric S-10 Pickup Truck.

DTIC Science & Technology

1997-12-01

the result is increased power and efficiency. The Kohler CH22 has a compression ratio of 8:1 in stock form. Natural aspirated spark ignition engines...a schematic layout of the acoustic intensity survey grid areas. B-8 N O c a 3 0» X © © © © © H H Z w S « S ( vap ) ids B-9...l _l _i li- u. LL cr LL ir 1- i Ü c CD 3 cr c m O OS © o OS o cu Q Z Ö o a H U o o OS NX SB H OS p o NX CO !■-- ( vaP

TOPSIS-based parametric optimization of compression ignition engine performance and emission behavior with bael oil blends for different EGR and charge inlet temperature.

PubMed

Muniappan, Krishnamoorthi; Rajalingam, Malayalamurthi

2018-05-02

The demand for higher fuel energy and lesser exhaust emissions of diesel engines can be achieved by fuel being used and engine operating parameters. In the present work, effects of engine speed (RPM), injection timing (IT), injection pressure (IP), and compression ratio (CR) on performance and emission characteristics of a compression ignition (CI) engine were investigated. The ternary test fuel of 65% diesel + 25% bael oil + 10% diethyl ether (DEE) was used in this work and test was conducted at different charge inlet temperature (CIT) and exhaust gas recirculation (EGR). All the experiments are conducted at the tradeoff engine load that is 75% engine load. When operating the diesel engine with 320 K CIT, brake thermal efficiency (BTE) is improved to 28.6%, and carbon monoxide (CO) and hydrocarbon (HC) emissions have been reduced to 0.025% and 12.5 ppm at 18 CR. The oxide of nitrogen (NOx) has been reduced to 240 ppm at 1500 rpm for 30% EGR mode. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) method is frequently used in multi-factor selection and gray correlation analysis method is used to study uncertain of the systems.

Multiple Fatigue Failure Behaviors and Long-Life Prediction Approach of Carburized Cr-Ni Steel with Variable Stress Ratio

PubMed Central

Deng, Hailong; Li, Wei; Zhao, Hongqiao; Sakai, Tatsuo

2017-01-01

Axial loading tests with stress ratios R of −1, 0 and 0.3 were performed to examine the fatigue failure behavior of a carburized Cr-Ni steel in the long-life regime from 104 to 108 cycles. Results show that this steel represents continuously descending S-N characteristics with interior inclusion-induced failure under R = −1, whereas it shows duplex S-N characteristics with surface defect-induced failure and interior inclusion-induced failure under R = 0 and 0.3. The increasing tension eliminates the effect of compressive residual stress and promotes crack initiation from the surface or interior defects in the carburized layer. The FGA (fine granular area) formation greatly depends on the number of loading cycles, but can be inhibited by decreasing the compressive stress. Based on the evaluation of the stress intensity factor at the crack tip, the surface and interior failures in the short life regime can be characterized by the crack growth process, while the interior failure with the FGA in the long life regime can be characterized by the crack initiation process. In view of the good agreement between predicted and experimental results, the proposed approach can be well utilized to predict fatigue lives associated with interior inclusion-FGA-fisheye induced failure, interior inclusion-fisheye induced failure, and surface defect induced failure. PMID:28906454

Whole-body low-dose computed tomography in multiple myeloma staging: Superior diagnostic performance in the detection of bone lesions, vertebral compression fractures, rib fractures and extraskeletal findings compared to radiography with similar radiation exposure.

PubMed

Lambert, Lukas; Ourednicek, Petr; Meckova, Zuzana; Gavelli, Giampaolo; Straub, Jan; Spicka, Ivan

2017-04-01

The primary objective of the present prospective study was to compare the diagnostic performance of conventional radiography (CR) and whole-body low-dose computed tomography (WBLDCT) with a comparable radiation dose reconstructed using hybrid iterative reconstruction technique, in terms of the detection of bone lesions, skeletal fractures, vertebral compressions and extraskeletal findings. The secondary objective was to evaluate lesion attenuation in relation to its size. A total of 74 patients underwent same-day skeletal survey by CR and WBLDCT. In CR and WBLDCT, two readers assessed the number of osteolytic lesions at each region and stage according to the International Myeloma Working Group (IMWG) criteria. A single reader additionally assessed extraskeletal findings and their significance, the number of vertebral compressions and bone fractures. The radiation exposure was 2.7±0.9 mSv for WBLDCT and 2.5±0.9 mSv for CR (P=0.054). CR detected bone involvement in 127 out of 486 regions (26%; P<0.0001), confirmed by WBLDCT. CR underestimated the disease stage in 16% and overestimated it in 8% of the patients (P=0.0077). WBLDCT detected more rib fractures compared with CR (188 vs. 47; P<0.0001), vertebral compressions (93 vs. 67; P=0.010) and extraskeletal findings (194 vs. 52; P<0.0001). There was no correlation observed between lesion size (≥5 mm) and its attenuation (r=-0.006; P=0.93). The inter-observer agreement for the presence of osteolytic lesions was κ=0.76 for WBLDCT, and κ=0.55 for CR. The present study concluded that WBLDCT with hybrid iterative reconstruction technique demonstrates superiority to CR with an identical radiation dose in the detection of bone lesions, skeletal fractures, vertebral compressions and extraskeletal findings, which results in up- or downstaging in 24% patients according to the IMWG criteria. The attenuation of osteolytic lesions can be measured with the avoidance of the partial volume effect.

An effective and efficient compression algorithm for ECG signals with irregular periods.

PubMed

Chou, Hsiao-Hsuan; Chen, Ying-Jui; Shiau, Yu-Chien; Kuo, Te-Son

2006-06-01

This paper presents an effective and efficient preprocessing algorithm for two-dimensional (2-D) electrocardiogram (ECG) compression to better compress irregular ECG signals by exploiting their inter- and intra-beat correlations. To better reveal the correlation structure, we first convert the ECG signal into a proper 2-D representation, or image. This involves a few steps including QRS detection and alignment, period sorting, and length equalization. The resulting 2-D ECG representation is then ready to be compressed by an appropriate image compression algorithm. We choose the state-of-the-art JPEG2000 for its high efficiency and flexibility. In this way, the proposed algorithm is shown to outperform some existing arts in the literature by simultaneously achieving high compression ratio (CR), low percent root mean squared difference (PRD), low maximum error (MaxErr), and low standard derivation of errors (StdErr). In particular, because the proposed period sorting method rearranges the detected heartbeats into a smoother image that is easier to compress, this algorithm is insensitive to irregular ECG periods. Thus either the irregular ECG signals or the QRS false-detection cases can be better compressed. This is a significant improvement over existing 2-D ECG compression methods. Moreover, this algorithm is not tied exclusively to JPEG2000. It can also be combined with other 2-D preprocessing methods or appropriate codecs to enhance the compression performance in irregular ECG cases.

ECG compression using non-recursive wavelet transform with quality control

NASA Astrophysics Data System (ADS)

Liu, Je-Hung; Hung, King-Chu; Wu, Tsung-Ching

2016-09-01

While wavelet-based electrocardiogram (ECG) data compression using scalar quantisation (SQ) yields excellent compression performance, a wavelet's SQ scheme, however, must select a set of multilevel quantisers for each quantisation process. As a result of the properties of multiple-to-one mapping, however, this scheme is not conducive for reconstruction error control. In order to address this problem, this paper presents a single-variable control SQ scheme able to guarantee the reconstruction quality of wavelet-based ECG data compression. Based on the reversible round-off non-recursive discrete periodised wavelet transform (RRO-NRDPWT), the SQ scheme is derived with a three-stage design process that first uses genetic algorithm (GA) for high compression ratio (CR), followed by a quadratic curve fitting for linear distortion control, and the third uses a fuzzy decision-making for minimising data dependency effect and selecting the optimal SQ. The two databases, Physikalisch-Technische Bundesanstalt (PTB) and Massachusetts Institute of Technology (MIT) arrhythmia, are used to evaluate quality control performance. Experimental results show that the design method guarantees a high compression performance SQ scheme with statistically linear distortion. This property can be independent of training data and can facilitate rapid error control.

Accelerated echo-planar J-resolved spectroscopic imaging in the human brain using compressed sensing: a pilot validation in obstructive sleep apnea.

PubMed

Sarma, M K; Nagarajan, R; Macey, P M; Kumar, R; Villablanca, J P; Furuyama, J; Thomas, M A

2014-06-01

Echo-planar J-resolved spectroscopic imaging is a fast spectroscopic technique to record the biochemical information in multiple regions of the brain, but for clinical applications, time is still a constraint. Investigations of neural injury in obstructive sleep apnea have revealed structural changes in the brain, but determining the neurochemical changes requires more detailed measurements across multiple brain regions, demonstrating a need for faster echo-planar J-resolved spectroscopic imaging. Hence, we have extended the compressed sensing reconstruction of prospectively undersampled 4D echo-planar J-resolved spectroscopic imaging to investigate metabolic changes in multiple brain locations of patients with obstructive sleep apnea and healthy controls. Nonuniform undersampling was imposed along 1 spatial and 1 spectral dimension of 4D echo-planar J-resolved spectroscopic imaging, and test-retest reliability of the compressed sensing reconstruction of the nonuniform undersampling data was tested by using a brain phantom. In addition, 9 patients with obstructive sleep apnea and 11 healthy controls were investigated by using a 3T MR imaging/MR spectroscopy scanner. Significantly reduced metabolite differences were observed between patients with obstructive sleep apnea and healthy controls in multiple brain regions: NAA/Cr in the left hippocampus; total Cho/Cr and Glx/Cr in the right hippocampus; total NAA/Cr, taurine/Cr, scyllo-Inositol/Cr, phosphocholine/Cr, and total Cho/Cr in the occipital gray matter; total NAA/Cr and NAA/Cr in the medial frontal white matter; and taurine/Cr and total Cho/Cr in the left frontal white matter regions. The 4D echo-planar J-resolved spectroscopic imaging technique using the nonuniform undersampling-based acquisition and compressed sensing reconstruction in patients with obstructive sleep apnea and healthy brain is feasible in a clinically suitable time. In addition to brain metabolite changes previously reported by 1D MR spectroscopy, our results show changes of additional metabolites in patients with obstructive sleep apnea compared with healthy controls. © 2014 by American Journal of Neuroradiology.

Curvelet-based compressive sensing for InSAR raw data

NASA Astrophysics Data System (ADS)

Costa, Marcello G.; da Silva Pinho, Marcelo; Fernandes, David

2015-10-01

The aim of this work is to evaluate the compression performance of SAR raw data for interferometry applications collected by airborne from BRADAR (Brazilian SAR System operating in X and P bands) using the new approach based on compressive sensing (CS) to achieve an effective recovery with a good phase preserving. For this framework is desirable a real-time capability, where the collected data can be compressed to reduce onboard storage and bandwidth required for transmission. In the CS theory, a sparse unknown signals can be recovered from a small number of random or pseudo-random measurements by sparsity-promoting nonlinear recovery algorithms. Therefore, the original signal can be significantly reduced. To achieve the sparse representation of SAR signal, was done a curvelet transform. The curvelets constitute a directional frame, which allows an optimal sparse representation of objects with discontinuities along smooth curves as observed in raw data and provides an advanced denoising optimization. For the tests were made available a scene of 8192 x 2048 samples in range and azimuth in X-band with 2 m of resolution. The sparse representation was compressed using low dimension measurements matrices in each curvelet subband. Thus, an iterative CS reconstruction method based on IST (iterative soft/shrinkage threshold) was adjusted to recover the curvelets coefficients and then the original signal. To evaluate the compression performance were computed the compression ratio (CR), signal to noise ratio (SNR), and because the interferometry applications require more reconstruction accuracy the phase parameters like the standard deviation of the phase (PSD) and the mean phase error (MPE) were also computed. Moreover, in the image domain, a single-look complex image was generated to evaluate the compression effects. All results were computed in terms of sparsity analysis to provides an efficient compression and quality recovering appropriated for inSAR applications, therefore, providing a feasibility for compressive sensing application.

1100 to 1500 K Slow Plastic Compressive Behavior of NiAl-xCr Single Crystals

NASA Technical Reports Server (NTRS)

Whittenberger, J. Daniel; Darolia, Ram

2003-01-01

The compressive properties of near <001> and <111> oriented NiAl-2Cr single crystals and near <011> oriented NiAl-6Cr samples have been measured between 1100 and 1500 K. The 2Cr addition produced significant solid solution strengthening in NiAl, and the <111> and <001> single crystals possessed similar strengths. The 6Cr crystals were not stronger than the 2Cr versions. At 1100 and 1200 K plastic flow in all three Cr-modified materials was highly dependent on stress with exponents > 10. The <011> oriented 6Cr alloy exhibited a stress exponent of about 8 at 1400 and 1500 K; whereas both <001> and <111> NiAl-2Cr crystals possessed stress exponents near 3 which is indicative of a viscous dislocation glide creep mechanism. While the Cottrell-Jaswon solute drag model predicted creep rates within a factor of 3 at 1500 K for <001>-oriented NiAl-2Cr; this mechanism greatly over predicted creep rates for other orientations and at 1400 K for <001> crystals.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Efthimiopoulos, I.; Tsurkan, V.; Loidl, A.

We have conducted high-pressure measurements on the CuCr2O4 and CuCr2Se4 spinels to unravel the structural systematics of these materials under compression. Our studies have revealed diverse structural behavior in these two compounds. In particular, CuCr2O4 retains its ambient-pressure I41/amd structure up to 50 GPa. Close inspection of the lattice and interatomic parameters reveals a compressibility change near 23 GPa, which is accompanied by an expansion of the apical Cr–O bond distances. We speculate that an outer Cr3+ 3d orbital reorientation might be at play in this system, manifesting as the change in compressibility at that pressure point. On the othermore » hand, CuCr2Se4 undergoes a structural transformation from the starting Fd3¯m phase toward a monoclinic structure initiated at ~8 GPa and completed at ~20 GPa. This high-pressure behavior resembles that of ZnCr2Se4, and it appears that, unlike similar chalcogenide Cr spinels, steric effects take a leading role in this pressure-induced Fd3¯m → monoclinic transition. Close comparison of our results with the reported literature yields significant insights behind the pressure-induced structural systematics of this important family of materials, thus both allowing for the careful manipulation of the structural/physical properties of these systems by strain and promoting our understanding of similar pressure-induced effects in relevant systems.« less

Contact Behavior of Composite CrTiSiN Coated Dies in Compressing of Mg Alloy Sheets under High Pressure

PubMed Central

Yang, T.S.; Yao, S.H.; Chang, Y.Y.; Deng, J.H.

2018-01-01

Hard coatings have been adopted in cutting and forming applications for nearly two decades. The major purpose of using hard coatings is to reduce the friction coefficient between contact surfaces, to increase strength, toughness and anti-wear performance of working tools and molds, and then to obtain a smooth work surface and an increase in service life of tools and molds. In this report, we deposited a composite CrTiSiN hard coating, and a traditional single-layered TiAlN coating as a reference. Then, the coatings were comparatively studied by a series of tests. A field emission SEM was used to characterize the microstructure. Hardness was measured using a nano-indentation tester. Adhesion of coatings was evaluated using a Rockwell C hardness indentation tester. A pin-on-disk wear tester with WC balls as sliding counterparts was used to determine the wear properties. A self-designed compression and friction tester, by combining a Universal Testing Machine and a wear tester, was used to evaluate the contact behavior of composite CrTiSiN coated dies in compressing of Mg alloy sheets under high pressure. The results indicated that the hardness of composite CrTiSiN coating was lower than that of the TiAlN coating. However, the CrTiSiN coating showed better anti-wear performance. The CrTiSiN coated dies achieved smooth surfaces on the Mg alloy sheet in the compressing test and lower friction coefficient in the friction test, as compared with the TiAlN coating. PMID:29316687

Contact Behavior of Composite CrTiSiN Coated Dies in Compressing of Mg Alloy Sheets under High Pressure.

PubMed

Yang, T S; Yao, S H; Chang, Y Y; Deng, J H

2018-01-08

Hard coatings have been adopted in cutting and forming applications for nearly two decades. The major purpose of using hard coatings is to reduce the friction coefficient between contact surfaces, to increase strength, toughness and anti-wear performance of working tools and molds, and then to obtain a smooth work surface and an increase in service life of tools and molds. In this report, we deposited a composite CrTiSiN hard coating, and a traditional single-layered TiAlN coating as a reference. Then, the coatings were comparatively studied by a series of tests. A field emission SEM was used to characterize the microstructure. Hardness was measured using a nano-indentation tester. Adhesion of coatings was evaluated using a Rockwell C hardness indentation tester. A pin-on-disk wear tester with WC balls as sliding counterparts was used to determine the wear properties. A self-designed compression and friction tester, by combining a Universal Testing Machine and a wear tester, was used to evaluate the contact behavior of composite CrTiSiN coated dies in compressing of Mg alloy sheets under high pressure. The results indicated that the hardness of composite CrTiSiN coating was lower than that of the TiAlN coating. However, the CrTiSiN coating showed better anti-wear performance. The CrTiSiN coated dies achieved smooth surfaces on the Mg alloy sheet in the compressing test and lower friction coefficient in the friction test, as compared with the TiAlN coating.

Yttria catalyzed microstructural modifications in oxide dispersion strengthened V-4Cr-4Ti alloys synthesized by field assisted sintering technique

NASA Astrophysics Data System (ADS)

Krishnan, Vinoadh Kumar; Sinnaeruvadi, Kumaran; Verma, Shailendra Kumar; Dash, Biswaranjan; Agrawal, Priyanka; Subramanian, Karthikeyan

2017-08-01

The present work deals with synthesis, characterisation and elevated temperature mechanical property evaluation of V-4Cr-4Ti and oxide (yttria = 0.3, 0.6 and 0.9 at%) dispersion strengthened V-4Cr-4Ti alloy processed by mechanical alloying and field-assisted sintering, under optimal conditions. Microstructural parameters of both powder and sintered samples were deduced by X-ray diffraction (XRD) and further confirmed with high resolution transmission electron microscopy. Powder diffraction and electron microscopy study show that ball milling of starting elemental powders (V-4Cr-4Ti) with and without yttria addition has resulted in single phase α-V (V-4Cr-4Ti) alloy. Wherein, XRD and electron microscopy images of sintered samples have revealed phase separation (viz., Cr-V and Ti-V) and domain size reduction, with yttria addition. The reasons behind phase separation and domain size reduction with yttria addition during sintering are extensively discussed. Microhardness and high temperature compression tests were done on sintered samples. Yttria addition (0.3 and 0.6 at.%) increases the elevated temperature compressive strength and strain hardening exponent of α-V alloys. High temperature compression test of 0.9 at% yttria dispersed α-V alloy reveals a glassy behaviour.

Development of a plasma sprayed ceramic gas path seal for high pressure turbine application

NASA Technical Reports Server (NTRS)

Shiembob, L. T.

1978-01-01

Development of the plasma sprayed graded, layered ZRO2/CoCrAlY seal system for gas turbine engine blade tip seal applications up to 1589 K (2400 F) surface temperature was continued. The effect of changing ZRO2/CoCrAlY ratios in the intermediate layers on thermal stresses was evaluated analytically with the goal of identifying the materials combinations which would minimize thermal stresses in the seal system. Three methods of inducing compressive residual stresses in the sprayed seal materials to offset tensile thermal stresses were analyzed. The most promising method, thermal prestraining, was selected based upon potential, feasibility and complexity considerations. The plasma spray equipment was modified to heat, control and monitor the substrate temperature during spraying. Specimens were fabricated and experimentally evaluated to: (1) substantiate the capability of the thermal prestrain method to develop compressive residual stresses in the sprayed structure and (2) define the effect of spraying on a heated substate on abradability, erosion and thermal shock characteristics of the seal system. Thermal stress analysis, including residual stresses and material properties variations, was performed and correlated with thermal shock test results. Seal system performance was assessed and recommendations for further development were made.

Microstructure and Room-Temperature Mechanical Properties of FeCrMoVTi x High-Entropy Alloys

NASA Astrophysics Data System (ADS)

Guo, Jun; Huang, Xuefei; Huang, Weigang

2017-07-01

FeCrMoVTi x ( x values represent the molar ratio, where x = 0, 0.5, 1.0, 1.5, and 2.0) high-entropy alloys were prepared by a vacuum arc melting method. The effects of Ti element on the microstructure and room-temperature mechanical properties of the as-cast FeCrMoVTi x alloys were investigated. The results show that the prepared alloys exhibited typical dendritic microstructure and the size of the microstructure became fine with increasing Ti content. The FeCrMoV alloy exhibited a single body-centered cubic structure (BCC1) and the alloys prepared with Ti element exhibited BCC1 + BCC2 mixed structure. The new BCC2 phase is considered as (Fe, Ti)-rich phase and was distributed in the dendrite region. With the increase of Ti content, the volume fraction of the BCC2 phase increased and its shape changed from a long strip to a network. For the FeCrMoV alloy, the fracture strength, plastic strain, and hardness reached as high as 2231 MPa, 28.2%, and 720 HV, respectively. The maximum hardness of 887 HV was obtained in the FeCrMoVTi alloy. However, the fracture strength, yield stress, and plastic strain of the alloys decreased continuously as Ti content increased. In the room-temperature compressive test, the alloys showed typical brittle fracture characteristics.

Monazite-type SrCr O 4 under compression

DOE PAGES

Gleissner, J.; Errandonea, Daniel; Segura, A.; ...

2016-10-20

We report a high-pressure study of monoclinic monazite-type SrCrO 4 up to 26 GPa. Therein we combined x-ray diffraction, Raman, and optical-absorption measurements with ab initio calculations, to find a pressure-induced structural phase transition of SrCrO 4 near 8-9 GPa. Evidence of a second phase transition was observed at 10-13 GPa. The crystal structures of the high-pressure phases were assigned to the tetragonal scheelite-type and monoclinic AgMnO 4-type structures. Both transitions produce drastic changes in the electronic band gap and phonon spectrum of SrCrO 4. We determined the pressure evolution of the band gap for the low- and high-pressure phasesmore » as well as the frequencies and pressure dependencies of the Raman-active modes. In all three phases most Raman modes harden under compression, however the presence of low-frequency modes which gradually soften is also detected. In monazite-type SrCrO 4, the band gap blueshifts under compression, but the transition to the scheelite phase causes an abrupt decrease of the band gap in SrCrO 4. Calculations showed good agreement with experiments and were used to better understand the experimental results. From x-ray-diffraction studies and calculations we determined the pressure dependence of the unit-cell parameters of the different phases and their ambient-temperature equations of state. The results are compared with the high-pressure behavior of other monazites, in particular PbCrO 4. A comparison of the high-pressure behavior of the electronic properties of SrCrO 4 (SrWO 4) and PbCrO 4 (PbWO 4) will also be made. Lastly, the possible occurrence of a third structural phase transition is discussed.« less

1300 K Compressive Properties of Directionally Solidified Ni-33Al-33Cr-1Mo

NASA Technical Reports Server (NTRS)

Whittenberger, J. Daniel; Raj, S. V.; Locci, Ivan E.

2000-01-01

The Ni-33Al-33Cr-1Mo eutectic has been directionally solidified by a modified Bridgeman technique at growth rates ranging from 7.6 to 508 mm/h to produce grain/cellular microstructures, containing alternating plates of NiAl and Cr alloyed with Mo. The grains had sharp boundaries for slower growth rates (< 12.7 mm/h), while faster growth rates (> 25.4 mm/h) lead to cells bounded by intercellular regions. Compressive testing at 1300 K indicated that alloys DS'ed at rates between 25.4 to 254 mm/h possessed the best strengths which exceed that for the as-cast alloy.

Fabrication, microstructure, properties and deformation mechanisms of a nanocrystalline aluminum-iron-chromium-titanium alloy by mechanical alloying

NASA Astrophysics Data System (ADS)

Luo, Hong

A multi-phase nanocrystalline Al93Fe3Cr2Ti 2 alloy containing 30 vol.% intermetallic particles was prepared via mechanical alloying starting from elemental powders, followed by hot extrusion. The grain size of 6-45 nm can be achieved after 30-hours of milling. Thermal stability of nanostructured Al93Fe3Ti2Cr 2 alloys was investigated using a variety of analytical techniques including modulated differential scanning calorimetry, X-ray diffraction, scanning electron microscopy, transmission electron microscopy. The MA-processed Al93Fe 3Ti2Cr2 alloy in the as-milled condition was composed of an Al-based supersaturated solid solution with high internal strains. Release of internal strains, intermetallic precipitation and grain growth occurred upon heating of the MA-processed Al alloy. Nevertheless, grain growth in the MA-processed Al alloy was very limited and fcc-Al grains with sizes in the range of 20 nm were still present in the alloys after exposure to 450°C (0.77 Tm). Systematic compressive tests and modulus measurements were performed as a function of temperature and strain rate to investigate the deformation behavior and mechanisms of the nc Al-Fe-Cr-Ti alloys. High strengths and moduli at both ambient and elevated temperatures have been demonstrated. The ductility of the nc Al93Fe3Cr2Ti2 alloy depends strongly on whether the oxide film at the prior powder particle boundary has been broken down or not. The MA-processed Al93Fe3Cr 2Ti2 alloy is brittle when the oxide film is continuous at PPB, and is ductile when the oxide film is broken down into discontinuous particles during extrusion. It is argued that the compressive strength at ambient temperature is controlled by propagation of dislocations into nc fcc-Al grains, whereas the compressive strength at elevated temperature is determined by dislocation propagation as well as dynamic recovery. Since the stress for dislocation propagation into nc fcc-Al grains increases with decreasing the grain size, the smaller the grain size, the higher the compressive strength. This new microstructural design approach could present opportunities for exploiting nc materials in structural applications at both ambient and elevated temperatures. The nanocrystalline Al-Fe-Cr-Ti alloy exhibited significant difference in deformation behavior between tension and compression at 25, 200 and 300°C. However, the strengths obtained in tension and compression were similar at 400°C. Systematic microstructure examinations and deformation mechanism analyses indicate that the asymmetry of this nc Al93Fe3Cr 2Ti2 alloy is related to its dislocation mediated plastic deformation mechanism, its nanoscale grain microstructure, and premature brittle failure in tension tests.

Effect of Compressive Mode I on the Mixed Mode I/II Fatigue Crack Growth Rate of 42CrMo4

NASA Astrophysics Data System (ADS)

Heirani, Hasan; Farhangdoost, Khalil

2018-01-01

Subsurface cracks in mechanical contact loading components are subjected to mixed mode I/II, so it is necessary to evaluate the fatigue behavior of materials under mixed mode loading. For this purpose, fatigue crack propagation tests are performed with compact tension shear specimens for several stress intensity factor (SIF) ratios of mode I and mode II. The effect of compressive mode I loading on mixed mode I/II crack growth rate and fracture surface is investigated. Tests are carried out for the pure mode I, pure mode II, and two different mixed mode loading angles. On the basis of the experimental results, mixed mode crack growth rate parameters are proposed according to Tanaka and Richard with Paris' law. Results show neither Richard's nor Tanaka's equivalent SIFs are very useful because these SIFs depend strongly on the loading angle, but Richard's equivalent SIF formula is more suitable than Tanaka's formula. The compressive mode I causes the crack closure, and the friction force between the crack surfaces resists against the crack growth. In compressive loading with 45° angle, d a/d N increases as K eq decreases.

Continuous direct compression as manufacturing platform for sustained release tablets.

PubMed

Van Snick, B; Holman, J; Cunningham, C; Kumar, A; Vercruysse, J; De Beer, T; Remon, J P; Vervaet, C

2017-03-15

This study presents a framework for process and product development on a continuous direct compression manufacturing platform. A challenging sustained release formulation with high content of a poorly flowing low density drug was selected. Two HPMC grades were evaluated as matrix former: standard Methocel CR and directly compressible Methocel DC2. The feeding behavior of each formulation component was investigated by deriving feed factor profiles. The maximum feed factor was used to estimate the drive command and depended strongly upon the density of the material. Furthermore, the shape of the feed factor profile allowed definition of a customized refill regime for each material. Inline NIRs was used to estimate the residence time distribution (RTD) in the mixer and monitor blend uniformity. Tablet content and weight variability were determined as additional measures of mixing performance. For Methocel CR, the best axial mixing (i.e. feeder fluctuation dampening) was achieved when an impeller with high number of radial mixing blades operated at low speed. However, the variability in tablet weight and content uniformity deteriorated under this condition. One can therefore conclude that balancing axial mixing with tablet quality is critical for Methocel CR. However, reformulating with the direct compressible Methocel DC2 as matrix former improved tablet quality vastly. Furthermore, both process and product were significantly more robust to changes in process and design variables. This observation underpins the importance of flowability during continuous blending and die-filling. At the compaction stage, blends with Methocel CR showed better tabletability driven by a higher compressibility as the smaller CR particles have a higher bonding area. However, tablets of similar strength were achieved using Methocel DC2 by targeting equal porosity. Compaction pressure impacted tablet properties and dissolution. Hence controlling thickness during continuous manufacturing of sustained release tablets was crucial to ensure reproducible dissolution. Copyright © 2017 Elsevier B.V. All rights reserved.

Modelling Nonlinear Dynamic Textures using Hybrid DWT-DCT and Kernel PCA with GPU

NASA Astrophysics Data System (ADS)

Ghadekar, Premanand Pralhad; Chopade, Nilkanth Bhikaji

2016-12-01

Most of the real-world dynamic textures are nonlinear, non-stationary, and irregular. Nonlinear motion also has some repetition of motion, but it exhibits high variation, stochasticity, and randomness. Hybrid DWT-DCT and Kernel Principal Component Analysis (KPCA) with YCbCr/YIQ colour coding using the Dynamic Texture Unit (DTU) approach is proposed to model a nonlinear dynamic texture, which provides better results than state-of-art methods in terms of PSNR, compression ratio, model coefficients, and model size. Dynamic texture is decomposed into DTUs as they help to extract temporal self-similarity. Hybrid DWT-DCT is used to extract spatial redundancy. YCbCr/YIQ colour encoding is performed to capture chromatic correlation. KPCA is applied to capture nonlinear motion. Further, the proposed algorithm is implemented on Graphics Processing Unit (GPU), which comprise of hundreds of small processors to decrease time complexity and to achieve parallelism.

Compressive sensing for efficient health monitoring and effective damage detection of structures

NASA Astrophysics Data System (ADS)

Jayawardhana, Madhuka; Zhu, Xinqun; Liyanapathirana, Ranjith; Gunawardana, Upul

2017-02-01

Real world Structural Health Monitoring (SHM) systems consist of sensors in the scale of hundreds, each sensor generating extremely large amounts of data, often arousing the issue of the cost associated with data transfer and storage. Sensor energy is a major component included in this cost factor, especially in Wireless Sensor Networks (WSN). Data compression is one of the techniques that is being explored to mitigate the effects of these issues. In contrast to traditional data compression techniques, Compressive Sensing (CS) - a very recent development - introduces the means of accurately reproducing a signal by acquiring much less number of samples than that defined by Nyquist's theorem. CS achieves this task by exploiting the sparsity of the signal. By the reduced amount of data samples, CS may help reduce the energy consumption and storage costs associated with SHM systems. This paper investigates CS based data acquisition in SHM, in particular, the implications of CS on damage detection and localization. CS is implemented in a simulation environment to compress structural response data from a Reinforced Concrete (RC) structure. Promising results were obtained from the compressed data reconstruction process as well as the subsequent damage identification process using the reconstructed data. A reconstruction accuracy of 99% could be achieved at a Compression Ratio (CR) of 2.48 using the experimental data. Further analysis using the reconstructed signals provided accurate damage detection and localization results using two damage detection algorithms, showing that CS has not compromised the crucial information on structural damages during the compression process.

Effect of Cr2O3 addition on the oxidation induration mechanism of Hongge vanadium titanomagnetite pellets

NASA Astrophysics Data System (ADS)

Li, Wei; Wang, Nan; Fu, Gui-qin; Chu, Man-sheng; Zhu, Miao-yong

2018-04-01

As part of a research project to develop a novel clean smelting process for the comprehensive utilization of Hongge vanadium titanomagnetite (HVTM), in this study, the effect of Cr2O3 addition on the oxidation induration mechanism of HVTM pellets (HVTMPs) was investigated in detail. The results showed that the compressive strength of the HVTMPs was greatly weakened by the Cr2O3 addition, mainly because of a substantial increase in the porosity of the HVTMPs. The Cr2O3 addition marginally affected the phase composition but greatly affected the microstructural changes of the HVTMPs. Increased amounts of Cr2O3 resulted in a decrease in the uniform distribution of the hematite grains and in an increase in the Fe-Cr solid solutions (Fe1.2Cr0.8O3 and Fe0.7Cr1.3O3) embedded in the hematite grains. Moreover, the compact hematite was destroyed by forming a dispersed structure and the hematite recrystallization was hindered during the oxidation induration, which adversely affected the compressive strength. On the basis of these results, a schematic was formulated to describe the oxidation induration mechanism with different amounts of added Cr2O3. This study provides theoretical and technical foundations for the effective production of HVTMPs and a reference for chromium-bearing minerals.

Accelerated whole brain intracranial vessel wall imaging using black blood fast spin echo with compressed sensing (CS-SPACE).

PubMed

Zhu, Chengcheng; Tian, Bing; Chen, Luguang; Eisenmenger, Laura; Raithel, Esther; Forman, Christoph; Ahn, Sinyeob; Laub, Gerhard; Liu, Qi; Lu, Jianping; Liu, Jing; Hess, Christopher; Saloner, David

2018-06-01

Develop and optimize an accelerated, high-resolution (0.5 mm isotropic) 3D black blood MRI technique to reduce scan time for whole-brain intracranial vessel wall imaging. A 3D accelerated T 1 -weighted fast-spin-echo prototype sequence using compressed sensing (CS-SPACE) was developed at 3T. Both the acquisition [echo train length (ETL), under-sampling factor] and reconstruction parameters (regularization parameter, number of iterations) were first optimized in 5 healthy volunteers. Ten patients with a variety of intracranial vascular disease presentations (aneurysm, atherosclerosis, dissection, vasculitis) were imaged with SPACE and optimized CS-SPACE, pre and post Gd contrast. Lumen/wall area, wall-to-lumen contrast ratio (CR), enhancement ratio (ER), sharpness, and qualitative scores (1-4) by two radiologists were recorded. The optimized CS-SPACE protocol has ETL 60, 20% k-space under-sampling, 0.002 regularization factor with 20 iterations. In patient studies, CS-SPACE and conventional SPACE had comparable image scores both pre- (3.35 ± 0.85 vs. 3.54 ± 0.65, p = 0.13) and post-contrast (3.72 ± 0.58 vs. 3.53 ± 0.57, p = 0.15), but the CS-SPACE acquisition was 37% faster (6:48 vs. 10:50). CS-SPACE agreed with SPACE for lumen/wall area, ER measurements and sharpness, but marginally reduced the CR. In the evaluation of intracranial vascular disease, CS-SPACE provides a substantial reduction in scan time compared to conventional T 1 -weighted SPACE while maintaining good image quality.

Strong magnetization and Chern insulators in compressed graphene/CrI 3 van der Waals heterostructures

NASA Astrophysics Data System (ADS)

Zhang, Jiayong; Zhao, Bao; Zhou, Tong; Xue, Yang; Ma, Chunlan; Yang, Zhongqin

2018-02-01

Graphene-based heterostructures are a promising material system for designing the topologically nontrivial Chern insulating devices. Recently, a two-dimensional monolayer ferromagnetic insulator CrI3 was successfully synthesized in experiments [B. Huang et al., Nature (London) 546, 270 (2017), 10.1038/nature22391]. Here, these two interesting materials are proposed to build a heterostructure (Gr /CrI3). Our first-principles calculations show that the system forms a van der Waals (vdW) heterostructure, which is relatively facilely fabricated in experiments. A Chern insulating state is acquired in the Gr /CrI3 heterostructure if the vdW gap is compressed to a distance between about 3.3 and 2.4 Å, corresponding to a required external pressure between about 1.4 and 18.3 GPa. Amazingly, very strong magnetization (about 150 meV) is found in graphene, induced by the substrate CrI3, despite the vdW interactions between them. A low-energy effective model is employed to understand the mechanism. The work functions, contact types, and band alignments of the Gr /CrI3 heterostructure system are also studied. Our work demonstrates that the Gr /CrI3 heterostructure is a promising system to observe the quantum anomalous Hall effect at high temperatures (up to 45 K) in experiments.

Immobilization of Chromium from Liquid Waste of Electroplating Home-Industries by Fly Ash Geopolymerization

NASA Astrophysics Data System (ADS)

Fansuri, H.; Erviana, E.; Rosyidah, M.; Iqbal, R. M.; Utomo, W. P.; Nurlina

2018-05-01

Immobilization is one of methods that can be used to overcome the problem of water pollution by heavy metals, such as chromium, which is possibly produced in an electroplating home-industry. One method that can be used to immobilize heavy metals is by using the waste water as a reactant in a geopolymerization process. The resulting geopolymer will contain such heavy metals and keep them from being dispersed into the environment. In this research, the immobilization was carried out by geopolymerization of fly ash from PT. IPMOMI (International Power Mitsui Operation and Maintenance) in Probolinggo, Indonesia, which pass through 60 (FA 60), 100 (FA 100), and 200 (FA 200) mesh sieve and using wastewater from electroplating home-industries in Ngingas Village, Sidoarjo-Indonesia, or a solution of Cr(NO3)3.9H2O as one of its reactants. The composition of the geopolymerization follows the results of previous research, i.e using the ratio of Solid to Liquid (S/L) = 3.59, Na2O/SiO2 = 0.67, H2O/Na2O = 3.33 and SiO2/Al2O3 = 6.46. Experimental results show that the compressive strength of geopolymers without heavy metals addition increases when the particle size decreases. Geopolymer made of FA 100 has the highest compressive strength i.e 35.05 MPa. The addition of a chromium-containing wastewater in FA 100 geopolymerization produce a geopolymer with a lower compressive strength i.e 26.42 MPa while the addition of Cr(NO3)3·9H2O solution produce geopolymer with compressive strength of 24.47 MPa. The SEM-EDX photo shows that chrome was evenly dispersed in the geopolymer. Leaching test with TCLP method (Toxicity Characteristic Leaching Procedure) on the geopolymer product showed that no chrome content in the leachate was found. This suggests that chromium is immobilized by geopolymers very well.

Transform-Based Channel-Data Compression to Improve the Performance of a Real-Time GPU-Based Software Beamformer.

PubMed

Lok, U-Wai; Li, Pai-Chi

2016-03-01

Graphics processing unit (GPU)-based software beamforming has advantages over hardware-based beamforming of easier programmability and a faster design cycle, since complicated imaging algorithms can be efficiently programmed and modified. However, the need for a high data rate when transferring ultrasound radio-frequency (RF) data from the hardware front end to the software back end limits the real-time performance. Data compression methods can be applied to the hardware front end to mitigate the data transfer issue. Nevertheless, most decompression processes cannot be performed efficiently on a GPU, thus becoming another bottleneck of the real-time imaging. Moreover, lossless (or nearly lossless) compression is desirable to avoid image quality degradation. In a previous study, we proposed a real-time lossless compression-decompression algorithm and demonstrated that it can reduce the overall processing time because the reduction in data transfer time is greater than the computation time required for compression/decompression. This paper analyzes the lossless compression method in order to understand the factors limiting the compression efficiency. Based on the analytical results, a nearly lossless compression is proposed to further enhance the compression efficiency. The proposed method comprises a transformation coding method involving modified lossless compression that aims at suppressing amplitude data. The simulation results indicate that the compression ratio (CR) of the proposed approach can be enhanced from nearly 1.8 to 2.5, thus allowing a higher data acquisition rate at the front end. The spatial and contrast resolutions with and without compression were almost identical, and the process of decompressing the data of a single frame on a GPU took only several milliseconds. Moreover, the proposed method has been implemented in a 64-channel system that we built in-house to demonstrate the feasibility of the proposed algorithm in a real system. It was found that channel data from a 64-channel system can be transferred using the standard USB 3.0 interface in most practical imaging applications.

High-pressure X-ray diffraction and Raman spectroscopy of CaFe2O4-type β-CaCr2O4

NASA Astrophysics Data System (ADS)

Zhai, Shuangmeng; Yin, Yuan; Shieh, Sean R.; Shan, Shuangming; Xue, Weihong; Wang, Ching-Pao; Yang, Ke; Higo, Yuji

2016-04-01

In situ high-pressure synchrotron X-ray diffraction and Raman spectroscopic studies of orthorhombic CaFe2O4-type β-CaCr2O4 chromite were carried out up to 16.2 and 32.0 GPa at room temperature using multi-anvil apparatus and diamond anvil cell, respectively. No phase transition was observed in this study. Fitting a third-order Birch-Murnaghan equation of state to the P-V data yields a zero-pressure volume of V 0 = 286.8(1) Å3, an isothermal bulk modulus of K 0 = 183(5) GPa and the first pressure derivative of isothermal bulk modulus K 0' = 4.1(8). Analyses of axial compressibilities show anisotropic elasticity for β-CaCr2O4 since the a-axis is more compressible than the b- and c-axis. Based on the obtained and previous results, the compressibility of several CaFe2O4-type phases was compared. The high-pressure Raman spectra of β-CaCr2O4 were analyzed to determine the pressure dependences and mode Grüneisen parameters of Raman-active bands. The thermal Grüneisen parameter of β-CaCr2O4 is determined to be 0.93(2), which is smaller than those of CaFe2O4-type CaAl2O4 and MgAl2O4.

Evidence of the impacting body of the Ries crater - the discovery of Fe-Cr-Ni veinlets below the crater bottom

USGS Publications Warehouse

El, Goresy A.; Chao, E.C.T.

1976-01-01

Fe-Cr-Ni particles and veinlets have been discovered in the top 15 m of the compressed zone with abundant shatter cones below the bottom of the Ries crater. The metallic particles are less than a few microns across. They occur in various minerals along healed intergranular and locally in intragranular microfractures in quartz diorite, amphibolite and chloritized granite of the basement crystalline rocks. The particles consist of major Fe, Cr, and Ni with minor Si and Ca. Origin due to contamination is absolutely ruled out. We believe that these Fe-Cr-Ni particles are probably condensed from the vaporized impacting body which produced the Ries crater. These particles were injected with high velocity into microfractures near the top of the compressed zone, implanted in and across various minerals before these microfractures were resealed. The presence of Si and Ca as well as the fact that the Cr content is nearly twice that of Ni, led us to conclude that the Ries impacting body is very likely not an iron meteorite but a stony meteorite. ?? 1976.

Effects of Alfvénic Drift on Diffusive Shock Acceleration at Weak Cluster Shocks

NASA Astrophysics Data System (ADS)

Kang, Hyesung; Ryu, Dongsu

2018-03-01

Non-detection of γ-ray emission from galaxy clusters has challenged diffusive shock acceleration (DSA) of cosmic-ray (CR) protons at weak collisionless shocks that are expected to form in the intracluster medium. As an effort to address this problem, we here explore possible roles of Alfvén waves self-excited via resonant streaming instability during the CR acceleration at parallel shocks. The mean drift of Alfvén waves may either increase or decrease the scattering center compression ratio, depending on the postshock cross-helicity, leading to either flatter or steeper CR spectra. We first examine such effects at planar shocks, based on the transport of Alfvén waves in the small amplitude limit. For the shock parameters relevant to cluster shocks, Alfvénic drift flattens the CR spectrum slightly, resulting in a small increase of the CR acceleration efficiency, η. We then consider two additional, physically motivated cases: (1) postshock waves are isotropized via MHD and plasma processes across the shock transition, and (2) postshock waves contain only forward waves propagating along with the flow due to a possible gradient of CR pressure behind the shock. In these cases, Alfvénic drift could reduce η by as much as a factor of five for weak cluster shocks. For the canonical parameters adopted here, we suggest η ∼ 10‑4–10‑2 for shocks with sonic Mach number M s ≈ 2–3. The possible reduction of η may help ease the tension between non-detection of γ-rays from galaxy clusters and DSA predictions.

Reproducibility over a 1-month period of 1H-MR spectroscopic imaging NAA/Cr ratios in clinically stable multiple sclerosis patients.

PubMed

Mostert, J P; Blaauw, Y; Koch, M W; Kuiper, A J; Hoogduin, J M; De Keyser, J

2008-08-01

N-acetylaspartate/creatine (NAA/Cr) ratios, assessed with proton magnetic resonance spectroscopy, are increasingly used as a surrogate marker for axonal dysfunction and degeneration in multiple sclerosis (MS). The purpose of this study was to test short-time reproducibility of NAA/Cr ratios in patients with clinically stable MS. In 35 MS patients we analysed NAA/Cr ratios obtained with (1)H-MR spectroscopic imaging at the centrum semiovale either with lateral ventricles partially included (group 1; n=15) or more cranially with no ventricles included (group 2; n=20). To test short-term reproducibility of the NAA/Cr measurements, patients were scanned twice 4 weeks apart. We determined mean NAA/Cr and Cho/Cr ratios of 12 grey matter and 24 white matter voxels. Mean NAA/Cr ratios of both the white and grey matter did not change after 4 weeks. Overall 4-week reproducibility of the NAA/Cr ratio, expressed as coefficient of variation, was 4.8% for grey matter and 3.5% for white matter. Reproducibility of cranial scanning of the ventricles was slightly better than with cerebrospinal fluid included. Our study shows good short-term reproducibility of NAA/Cr ratio measurements in the centrum semiovale, which supports the reliability of this technique for longitudinal studies.

Sustained Local Release of Methylprednisolone From a Thiol-Acrylate Poly(Ethylene Glycol) Hydrogel for Treating Chronic Compressive Radicular Pain.

PubMed

Slotkin, Jonathan R; Ness, Jennifer K; Snyder, Kristin M; Skiles, Amanda A; Woodard, Eric J; OʼShea, Timothy; Layer, Rick T; Aimetti, Alex A; Toms, Steven A; Langer, Robert; Tapinos, Nikos

2016-04-01

A preclinical animal model of chronic ligation of the sciatic nerve was used to compare the effectiveness of a slow-release hydrogel carrying methylprednisolone to methylprednisolone injection alone, which simulates the current standard of care for chronic compressive radiculopathy (CR). To extend the short-term benefits of steroid injections by using a nonswelling, biodegradable hydrogel as carrier to locally release methylprednisolone in a regulated and sustained way at the site of nerve compression. CR affects millions worldwide annually, and is a cause of costly disability with significant societal impact. Currently, a leading nonsurgical therapy involves epidural injection of steroids to temporarily alleviate the pain associated with CR. However, an effective way to extend the short-term effect of steroid treatment to address the chronic component of CR does not exist. We induced chronic compression injury of the sciatic nerves of rats by permanent ligation. Forty-eight hours later we injected our methylprednisolone infused hydrogel and assessed the effectiveness of our treatment for 4 weeks. We quantified mechanical hyperalgesia using a Dynamic Plantar Aesthesiometer (Ugo Basile, Stoelting Co., IL, USA), whereas gait analysis was conducted using the Catwalk automated gait analysis platform (Noldus, Leesburg, VA, USA). Macrophage staining was performed with immunohistochemistry and quantification of monocyte chemoattractant protein-1 in sciatic nerve lysates was performed with multiplex immunoassay using a SECTOR Imager 2400A (Meso Scale Discovery, Rockville, MA, USA). We demonstrate that using the hydrogel to deliver methylprednisolone results in significant (P < 0.05) reduction of hyperalgesia and improvement in the gait pattern of animals with chronic lesions as compared with animals treated with steroid alone. In addition, animals treated with hydrogel plus steroid showed significant reduction in the number of infiltrating macrophages at the sciatic nerve and reduced expression of the neuroinflammatory chemokine monocyte chemoattractant protein-1 (P < 0.05). Use of hydrogels as carriers for sustained local release of steroids provides significantly better control of pain in an animal model of chronic CR. Our steroid-infused hydrogel could be an effective extender of the short-term benefits of epidural steroid injections for patients with chronic compression-induced radicular pain. N/A.

Structural and electronic evolution of Cr[subscript 2]O[subscript 3] on compression to 55 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dera, Przemyslaw; Lavina, Barbara; Meng, Yue

2016-08-15

Synchrotron single-crystal x-ray diffraction experiments have been performed on corundum-type Cr{sub 2}O{sub 3} up to a pressure of 55 GPa in Ne and He pressure transmitting media. Diffraction experiments were complemented by measurements of optical absorption spectra with single crystal samples up to 60 GPa. Results of the diffraction data analysis rule out the earlier reported monoclinic distortion at 15-30 GPa, but indicate evidence of two discontinuous transitions of electronic or magnetic nature, most likely associated with a change in magnetic ordering and charge transfer. The compression mechanism established from single crystal refinements indicates much smaller distortion of the Cr{supmore » 3+} coordination environment than was previously assumed.« less

Chromium Oxidation State in Planetary Basalts: Oxygen Fugacity Indicator and Critical Variable for Cr-Spinel Stability

NASA Technical Reports Server (NTRS)

Bell, A. S.; Burger, P. V.; Le, Loan; Papike, J. J.; Jone, J.; Shearer, C. K.

2014-01-01

Cr is a ubiquitous and relatively abundant minor element in basaltic, planetary magmas. At the reduced oxidation states (

Evaluation of Digital Compressed Sensing for Real-Time Wireless ECG System with Bluetooth low Energy.

PubMed

Wang, Yishan; Doleschel, Sammy; Wunderlich, Ralf; Heinen, Stefan

2016-07-01

In this paper, a wearable and wireless ECG system is firstly designed with Bluetooth Low Energy (BLE). It can detect 3-lead ECG signals and is completely wireless. Secondly the digital Compressed Sensing (CS) is implemented to increase the energy efficiency of wireless ECG sensor. Different sparsifying basis, various compression ratio (CR) and several reconstruction algorithms are simulated and discussed. Finally the reconstruction is done by the android application (App) on smartphone to display the signal in real time. The power efficiency is measured and compared with the system without CS. The optimum satisfying basis built by 3-level decomposed db4 wavelet coefficients, 1-bit Bernoulli random matrix and the most suitable reconstruction algorithm are selected by the simulations and applied on the sensor node and App. The signal is successfully reconstructed and displayed on the App of smartphone. Battery life of sensor node is extended from 55 h to 67 h. The presented wireless ECG system with CS can significantly extend the battery life by 22 %. With the compact characteristic and long term working time, the system provides a feasible solution for the long term homecare utilization.

Simulating cosmic ray physics on a moving mesh

NASA Astrophysics Data System (ADS)

Pfrommer, C.; Pakmor, R.; Schaal, K.; Simpson, C. M.; Springel, V.

2017-03-01

We discuss new methods to integrate the cosmic ray (CR) evolution equations coupled to magnetohydrodynamics on an unstructured moving mesh, as realized in the massively parallel AREPO code for cosmological simulations. We account for diffusive shock acceleration of CRs at resolved shocks and at supernova remnants in the interstellar medium (ISM) and follow the advective CR transport within the magnetized plasma, as well as anisotropic diffusive transport of CRs along the local magnetic field. CR losses are included in terms of Coulomb and hadronic interactions with the thermal plasma. We demonstrate the accuracy of our formalism for CR acceleration at shocks through simulations of plane-parallel shock tubes that are compared to newly derived exact solutions of the Riemann shock-tube problem with CR acceleration. We find that the increased compressibility of the post-shock plasma due to the produced CRs decreases the shock speed. However, CR acceleration at spherically expanding blast waves does not significantly break the self-similarity of the Sedov-Taylor solution; the resulting modifications can be approximated by a suitably adjusted, but constant adiabatic index. In first applications of the new CR formalism to simulations of isolated galaxies and cosmic structure formation, we find that CRs add an important pressure component to the ISM that increases the vertical scaleheight of disc galaxies and thus reduces the star formation rate. Strong external structure formation shocks inject CRs into the gas, but the relative pressure of this component decreases towards halo centres as adiabatic compression favours the thermal over the CR pressure.

A simple and efficient algorithm operating with linear time for MCEEG data compression.

PubMed

Titus, Geevarghese; Sudhakar, M S

2017-09-01

Popularisation of electroencephalograph (EEG) signals in diversified fields have increased the need for devices capable of operating at lower power and storage requirements. This has led to a great deal of research in data compression, that can address (a) low latency in the coding of the signal, (b) reduced hardware and software dependencies, (c) quantify the system anomalies, and (d) effectively reconstruct the compressed signal. This paper proposes a computationally simple and novel coding scheme named spatial pseudo codec (SPC), to achieve lossy to near lossless compression of multichannel EEG (MCEEG). In the proposed system, MCEEG signals are initially normalized, followed by two parallel processes: one operating on integer part and the other, on fractional part of the normalized data. The redundancies in integer part are exploited using spatial domain encoder, and the fractional part is coded as pseudo integers. The proposed method has been tested on a wide range of databases having variable sampling rates and resolutions. Results indicate that the algorithm has a good recovery performance with an average percentage root mean square deviation (PRD) of 2.72 for an average compression ratio (CR) of 3.16. Furthermore, the algorithm has a complexity of only O(n) with an average encoding and decoding time per sample of 0.3 ms and 0.04 ms respectively. The performance of the algorithm is comparable with recent methods like fast discrete cosine transform (fDCT) and tensor decomposition methods. The results validated the feasibility of the proposed compression scheme for practical MCEEG recording, archiving and brain computer interfacing systems.

Mn-Cr systematics in primitive meteorites: Insights from mineral separation and partial dissolution

NASA Astrophysics Data System (ADS)

Göpel, Christa; Birck, Jean-Louis; Galy, Albert; Barrat, Jean-Alix; Zanda, Brigitte

2015-05-01

Cr isotopic compositions have been measured on carbonaceous chondrites (CC): Tafassasset, Paris, Niger I, NWA 5958, NWA 8157 and Jbilet Winselwan. In bulk samples, the 54Cr/52Cr ratios (expressed as ε54Cr) range from 0.93 to 1.58 ε units. These values are in agreement with values characteristic for distinct petrologic types. Despite this 54Cr heterogeneity, the variability in the 53Cr/52Cr ratios (expressed as ε53Cr) of 0.2 ε units and the Mn/Cr ratios is consistent with the previous finding of an isochron in the Mn-Cr evolution diagram. The Mn/Cr ratio in CC corresponds to variable abundances of high-T condensate formed and separated at the beginning of the solar system, thus the canonical 53Mn/55Mn ratio can be defined. Based on a consistent chronology for U-Pb and Mn-Cr between the earliest objects formed in the solar nebula and the D'Orbigny angrite we define a canonical 53Mn/55Mn ratio and ε53Cri of 6.8 × 10-6 and -0.177, respectively. The internal Mn/Cr systematics in Tafassasset and Paris were studied by two approaches: leaching technique and mineral separation. Despite variable ε54Cr values (up to >30 ε) linear co-variations were found between ε53Cr and Mn/Cr ratio. The mineral separates as well as the leachates of Tafassasset fall on a common isochron indicating that (1) cooling of the Tafassasset's parent body occurred at 4563.5 ± 0.25 Ma, and that (2) 54Cr is decoupled from the other isotopes even though temperatures >900 °C have been reached during metamorphism. In the case of Paris, the leachates form an alignment with a 53Mn/55Mn ratio higher than the canonical value. This alignment is not an isochron but rather a mixing line. Based on leachates from various CM and CI, we propose the occurrence of three distinct Cr reservoirs in meteoritic material: PURE54, HIGH53 and LOW53 characterized by a ε53Cr and ε54Cr of 0 and 25,000, -2.17 and 8, and 0.5 and -151, respectively. PURE54 has already been described and is carried by highly refractory nano-spinel; HIGH53 is Mn-rich and most probably carried by sulfides in the matrix, whereas LOW53 is characterized by low Mn/Cr ratios and it is sensitive to metamorphism. This component could correspond to mineral phases such as refractory oxides and carbide. Variable mixing proportions of HIGH53 and LOW53 would explain the larger-than-expected uncertainty (MSWD of 5.5) on the CC bulk regression line. A Monte Carlo simulation allows us to evaluate the impact of the dispersion of the initial Cr isotopic ratios (as a function of variable HIGH53). The co-variation of the Mn/Cr ratio and the ε53Cr defined by the mineral separates from Paris corresponds to an age of 4566.44 +0.66/-0.75 Ma, while their ε54Cr still differ by at least 0.42 ε. This age is likely to date the segregation of forsteritic olivines (most probably from type I chondrules) from fayalitic olivines (from type II chondrules) and, given the sampling procedure by handpicking of hundreds of grains, corresponds to the average age of chondrule formation.

Cardiopulmonary resuscitation using the cardio vent device in a resuscitation model.

PubMed

Suner, Selim; Jay, Gregory D; Kleinman, Gary J; Woolard, Robert H; Jagminas, Liudvikas; Becker, Bruce M

2002-05-01

To compare the "Bellows on Sternum Resuscitation" (BSR) device that permits simultaneous compression and ventilation by one rescuer with two person cardiopulmonary resuscitation (CPR) with bag-valve-mask (BVM) ventilation in a single blind crossover study performed in the laboratory setting. Tidal volume and compression depth were recorded continuously during 12-min CPR sessions with the BSR device and two person CPR. Six CPR instructors performed a total of 1,894 ventilations and 10,532 compressions in 3 separate 12-min sessions. Mean tidal volume (MTV) and compression rate (CR) with the BSR device differed significantly from CPR with the BVM group (1242 mL vs. 1065 mL, respectively, p = 0.0018 and 63.2 compressions per minute (cpm) vs. 81.3 cpm, respectively, p = 0.0076). Error in compression depth (ECD) rate of 9.78% was observed with the BSR device compared to 8.49% with BMV CPR (p = 0.1815). Error rate was significantly greater during the second half of CPR sessions for both BSR and BVM groups. It is concluded that one-person CPR with the BSR device is equivalent to two-person CPR with BVM in all measured parameters except for CR. Both groups exhibited greater error rate in CPR performance in the latter half of 12-min CPR sessions.

Mach 10 experimental database of a three-dimensional scramjet inlet flow field

NASA Technical Reports Server (NTRS)

Holland, Scott D.

1995-01-01

The present work documents the experimental database of a combined computational and experimental parametric study of the internal aerodynamics of a generic three-dimensional sidewall compression scramjet inlet configuration at Mach 10. A total of 356 channels of pressure data, including static pressure orifices, pitot pressures, and exit flow rakes, along with oil flow and infrared thermography, provided a detailed experimental description of the flow. Mach 10 tests were performed for three geometric contraction ratios (3, 5, and 9), three Reynolds numbers (0.55 x 10(exp 6) per foot, 1.14 x 10(exp 6) per foot, and 2.15 x 10(exp 6) per foot), and three cowl positions (at the throat and two forward positions). For the higher contraction ratios, a large forward separation of the inflow boundary layer was observed, making the high contraction ratio configurations unsuitable for flight operation. A decrease in the freestream unit Reynolds number (Re) of only a factor of 2 led to a similar upstream separation. Although the presence of such large-scale separations leads to the question of whether the inlet is started, the presence of internal oblique swept shock interactions on the sidewalls seems to indicate that at least in the classical sense, the inlet is not unstarted. The laminar inflow boundary layer therefore appears to be very sensitive to increases in contraction ratio (CR) or decreases in Reynolds number; only the CR = 3 configuration with 0.25, and 50 percent cowl at Re = 2.15 x 10(exp 6) per foot operated 'on design'.

High-speed reconstruction of compressed images

NASA Astrophysics Data System (ADS)

Cox, Jerome R., Jr.; Moore, Stephen M.

1990-07-01

A compression scheme is described that allows high-definition radiological images with greater than 8-bit intensity resolution to be represented by 8-bit pixels. Reconstruction of the images with their original intensity resolution can be carried out by means of a pipeline architecture suitable for compact, high-speed implementation. A reconstruction system is described that can be fabricated according to this approach and placed between an 8-bit display buffer and the display's video system thereby allowing contrast control of images at video rates. Results for 50 CR chest images are described showing that error-free reconstruction of the original 10-bit CR images can be achieved.

Manganese-Chromium Isotope Systematics of Ivuna, Kainsaz and Other Carbonaceous Chondrites

NASA Technical Reports Server (NTRS)

Shukolyukov, A.; Lugmair, G. W.; Bogdanovski, O.

2003-01-01

We have shown earlier that the bulk samples of carbonaceous chondrites [CC] reveal excesses in both Cr-53 (Cr-53*) and Cr-54 (Cr-54*) as compared to the terrestrial standard value. The Cr-53/52 ratios in bulk samples of Orgueil (CI), Murray (CM), Allende (CV), and the Bencubbin/CH-like meteorite Hammadah Al Hambra 237 (HH237) are correlated with the respective Mn/Cr ratios. In contrast to CC, HH237 is characterized by a deficit of Cr-53 (-0.15 +/- 0.10(epsilon)) at a low Mn/Cr ratio of 0.07. The HH237 data point, however, falls on the CC line. Here we report new Mn-53 - Cr-53 results for the CC Kainsaz (CO) and Ivuna (CI).

Effect of Growth Rate on Elevated Temperature Plastic Flow and Room Temperature Fracture Toughness of Directionally Solidified NiAl-31Cr-3Mo

NASA Technical Reports Server (NTRS)

Whittenberger, J. Daniel; Raj, S. V.; Locci, I. E.; Salem, J. A.

1999-01-01

The eutectic system Ni-33Al-31Cr-3Mo was directionally solidified at rates ranging from 7.6 to 508 mm/h. Samples were examined for microstructure and alloy chemistry, compression tested at 1200 and 1300 K, and subjected to room temperature fracture toughness measurements. Lamellar eutectic grains were formed at 12.7 mm/h; however cellular structures with a radial eutectic pattern developed at faster growth rates. Elevated temperature compression testing between 10(exp -4) to 10(exp -7)/s did not reveal an optimum growth condition, nor did any single growth condition result in a significant fracture toughness advantage. The mechanical behavior, taken together, suggests that Ni-33Al-31Cr-3Mo grown at rates from 25.4 to 254 mm/h will have nominally equivalent properties.

Synthesis and characterization of two novel chiral-type formate frameworks templated by protonated diethylamine and ammonium cations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mączka, Mirosław, E-mail: m.maczka@int.pan.wroc.pl; Gągor, Anna; Hanuza, Jerzy

2017-01-15

Two novel formate frameworks templated by ammonium and diethylammonium (DEtA{sup +}) cations have been synthesized. Chemical analysis as well as optical, Raman and IR studies showed partial substitution of nickel ions by Cr(III) or Fe(III). X-ray diffraction revealed that these compounds crystallize in the chiral-type structure of P6{sub 3}22 symmetry. The oxygen atoms from formate ligands form octahedral coordination around the metal centers and the octahedra are bridged by the formate groups in the anti-anti mode configuration forming the hexagonal structure with large channels expanding along the c direction. The channels are filled with disordered DEtA{sup +} and NH{sub 4}{supmore » +} ions and they show unusual compression with the c/a ratio of only 0.862 and 0.852 for the iron- and chromium-containing compound, respectively. Magnetic studies revealed that the both compounds order magnetically at low temperatures but the ordering temperature is significantly higher for the iron compound (37 K) compared to the chromium analogue (26 K). - Graphical abstract: Temperature dependence of magnetization M of DEtAFeNi showing magnetic order at 37 K. - Highlights: • Two novel chiral formates of P6{sub 3}22 symmetry were synthesized. • The structures contain strongly compressed hexagonal channels filled with disordered cations. • The obtained compounds exhibit magnetic order at low temperatures. • Raman, IR and absorption spectra prove incorporation of Cr(III) and Fe(III) in the frameworks.« less

Structural and magnetic properties of hexagonal Cr1-δTe films grown on CdTe(001) by molecular beam epitaxy

NASA Astrophysics Data System (ADS)

Kanazawa, Ken; Yamawaki, Kazuma; Sekita, Naoya; Nishio, Yôtarô; Kuroda, Shinji; Mitome, Masanori; Bando, Yoshio

2015-04-01

We investigated the structural and magnetic properties of Cr1-δTe thin films grown on CdTe(001) layers by molecular beam epitaxy (MBE) with systematic variations of the ratio between Cr and Te fluxes and the substrate temperature Ts during the growth. Cr1-δTe of the hexagonal structure (hex-Cr1-δTe) was always formed irrespective of the growth conditions, but the growth orientation was different depending on the Cr/Te flux ratio and Ts. Hex-Cr1-δTe was grown in the [0001] axis in the range of small Cr/Te ratios and high Ts while it was also grown in the direction normal to the (1-102) plane at larger Cr/Te ratios or lower Ts. Hex-Cr1-δTe films grown in the both orientations show ferromagnetism, but they exhibit a clear contrast in the field dependence of perpendicular magnetization at 2 K; a square hysteretic loop in the film grown in the [0001] axis versus a round-shape loop in the film grown in the direction normal to the (1-102) plane. Moreover, the films grown in the [0001] axis at the smallest Cr/Te ratio show variations of ferromagnetic properties with Curie temperature (Tc) and the coercivity (Hc) varying according to the value of Ts.

Plastic behavior of two-phase intermetallic compounds based on L1{sub 2}-type (Al,Cr){sub 3}Ti

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, J.Y.; Wee, D.M.; Oh, M.H.

Plastic behavior of two-phase intermetallic compounds based on L1{sub 2}-type (Al,Cr){sub 3}Ti was investigated using compression test at R.T. and 77K. L1{sub 2} single phase alloys and two-phase alloys consisting of mainly L1{sub 2} phase and a few or 20% (mole percent) second phases were selected from Al-Ti-Cr phase diagram. In general, compared with L1{sub 2} single phase, two-phase alloys consisting of 20% second phase showed relatively high yield strength and poor ductility. Among the alloys, however, Al-21Ti-23Cr alloy consisting of 20% Cr{sub 2}Al phase showed available ductility as well as high yield strength. Plastic behavior of L1{sub 2} singlemore » phase alloys and two-phase alloys consisting of a few Cr{sub 2}Al was also investigated. Homogenization of arc melted ingots substantially reduced the amount of second phases but introduced extensive pore. When Cr content increased in L1{sub 2} single phase alloys after the homogenization, the volume fraction of pores in the alloys decreased, and no residual porosity was observed in two-phase alloys consisting of a few% Cr{sub 2}Al phase. Environmental effect on the ductility of the alloys was investigated using compression test at different strain rates (1.2 {times} 10{sup {minus}4}/s and 1.2 {times} 10{sup {minus}2}/s). Environmental embrittlement was least significant in Al-25Ti-10Cr alloy consisting of L1{sub 2} single phase among the alloys tested in this study. However, based on the combined estimation of the pore formation, environmental embrittlement and ingot cast structure, it could be supposed that Al-21Ti-23Cr alloy consisting of 20% Cr{sub 2}Al as a second phase is expected to show the best tensile elongation behavior among the materials tested.« less

Impact of Various Compression Ratio on the Compression Ignition Engine with Diesel and Jatropha Biodiesel

NASA Astrophysics Data System (ADS)

Sivaganesan, S.; Chandrasekaran, M.; Ruban, M.

2017-03-01

The present experimental investigation evaluates the effects of using blends of diesel fuel with 20% concentration of Methyl Ester of Jatropha biodiesel blended with various compression ratio. Both the diesel and biodiesel fuel blend was injected at 23º BTDC to the combustion chamber. The experiment was carried out with three different compression ratio. Biodiesel was extracted from Jatropha oil, 20% (B20) concentration is found to be best blend ratio from the earlier experimental study. The engine was maintained at various compression ratio i.e., 17.5, 16.5 and 15.5 respectively. The main objective is to obtain minimum specific fuel consumption, better efficiency and lesser Emission with different compression ratio. The results concluded that full load show an increase in efficiency when compared with diesel, highest efficiency is obtained with B20MEOJBA with compression ratio 17.5. It is noted that there is an increase in thermal efficiency as the blend ratio increases. Biodiesel blend has performance closer to diesel, but emission is reduced in all blends of B20MEOJBA compared to diesel. Thus this work focuses on the best compression ratio and suitability of biodiesel blends in diesel engine as an alternate fuel.

DNABIT Compress - Genome compression algorithm.

PubMed

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-22

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, "DNABIT Compress" for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that "DNABIT Compress" algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases.

Hypersonic Wind Tunnel Nozzle Survivability for T&E

DTIC Science & Technology

2007-03-01

Room-Temperature Compression Tests ..............................................................43 10. Strength of Hot-Rolled Inconel 600 (Ni-16Cr...6Fe, wt %) ...................................................45 11. Physical Properties of Inconel 600...Table 10. Strength of Hot-Rolled Inconel 600 (Ni-16Cr-6Fe, wt%) T, °C 0.2% Yield Stress (MPa) Ultimate Tensile Stress (MPa) 20 250 590 400 185 560

ECG compression using Slantlet and lifting wavelet transform with and without normalisation

NASA Astrophysics Data System (ADS)

Aggarwal, Vibha; Singh Patterh, Manjeet

2013-05-01

This article analyses the performance of: (i) linear transform: Slantlet transform (SLT), (ii) nonlinear transform: lifting wavelet transform (LWT) and (iii) nonlinear transform (LWT) with normalisation for electrocardiogram (ECG) compression. First, an ECG signal is transformed using linear transform and nonlinear transform. The transformed coefficients (TC) are then thresholded using bisection algorithm in order to match the predefined user-specified percentage root mean square difference (UPRD) within the tolerance. Then, the binary look up table is made to store the position map for zero and nonzero coefficients (NZCs). The NZCs are quantised by Max-Lloyd quantiser followed by Arithmetic coding. The look up table is encoded by Huffman coding. The results show that the LWT gives the best result as compared to SLT evaluated in this article. This transform is then considered to evaluate the effect of normalisation before thresholding. In case of normalisation, the TC is normalised by dividing the TC by ? (where ? is number of samples) to reduce the range of TC. The normalised coefficients (NC) are then thresholded. After that the procedure is same as in case of coefficients without normalisation. The results show that the compression ratio (CR) in case of LWT with normalisation is improved as compared to that without normalisation.

Microstructure characterization and room temperature deformation of a rapidly solidified NiAl-based eutectic alloy containing trace Dy

NASA Astrophysics Data System (ADS)

Li, Hutian; Guo, Jianting; Huai, Kaiwen; Ye, Hengqiang

2006-04-01

The microstructure and room temperature compressive deformation behavior of a rapidly solidified NiAl-Cr(Mo)-Dy eutectic alloy fabricated by water-cooled copper mold method were studied by a combination of SEM, EDS and compressive tests. The morphology stability after hot isostatic pressing (HIP) treatment was evaluated. Rapid solidification resulted in a shift in the coupled zone for the eutectic growth towards the Cr(Mo) phase, indicating a hypoeutectic composition, hence increasing the volume fraction of primary dendritic NiAl. Meanwhile, significantly refined microstructure and lamellar/rod-like Cr(Mo) transition were observed due to trace rare earth (RE) element Dy addition and rapid solidification effects. Compared with the results in literature [H.E. Cline, J.L. Walter, Metall. Trans. 1(1970)2907-2917; P. Ferrandini, W.W. Batista, R. Caram, J. Alloys Comp. 381(2004)91-98], an interesting phenomenon, viz., NiAl halos around the primary Cr(Mo) dendrites in solidified NiAl-Cr(Mo) hypereutectic alloy, was not observed in this study. This difference was interpreted in terms of their different reciprocal nucleation ability. In addition, it was proposed that the localized destabilization of morphology after HIP treatment is closely related to the presence of primary NiAl dendrites. The improved mechanical properties can be attributed to the synergistic effects of rapid solidification and Dy addition, which included refined microstructure, suppression of the crack development along eutectic grain boundaries, enhancement of density of geometrically necessary dislocations located at NiAl/Cr(Mo) interfaces and the Cr solubility extension in NiAl.

Deformation Behavior and Microstructure Evolution of As-Cast 42CrMo Alloy in Isothermal and Non-isothermal Compression

NASA Astrophysics Data System (ADS)

Qin, Fangcheng; Li, Yongtang; Qi, Huiping; Lv, Zhenhua

2016-11-01

The isothermal and non-isothermal multi-pass compression tests of centrifugal casting 42CrMo steel were conducted on a Gleeble-3500 thermal simulation machine. The effects of compression passes and finishing temperatures on deformation behavior and microstructure evolution were investigated. It is found that the microstructure is homogeneous with equiaxed grains, and the flow stress does not show significant change with the increase in passes, while the peak softening coefficient increases first and then decreases during inter-pass. Moreover, the dominant mechanisms of controlled temperature and accumulated static recrystallization for grain refinement and its homogeneous distribution are found after 5 passes deformation. As the finishing temperature increases, the flow stress decreases gradually, but the dynamic recrystallization accelerates and softening effect increases, resulting in the larger grain size and homogeneous microstructure. The microhardness decreases sharply because the sufficient softening occurs in microstructure. When the finishing temperature is 890 °C, the carbide particles are precipitated in the vicinity of the grain boundaries, thus inhibiting the dislocation motion. Thus, the higher finishing temperature (≥970 °C) for centrifugal casting 42CrMo alloy should be avoided in non-isothermal multi-pass deformation, which is beneficial to grain refinement and properties improvement.

Influence of Annealing on Microstructure and Mechanical Properties of Refractory CoCrMoNbTi0.4 High-Entropy Alloy

NASA Astrophysics Data System (ADS)

Zhang, Mina; Zhou, Xianglin; Zhu, Wuzhi; Li, Jinghao

2018-04-01

A novel refractory CoCrMoNbTi0.4 high-entropy alloy (HEA) was prepared via vacuum arc melting. After annealing treatment at different temperatures, the microstructure evolution, phase stability, and mechanical properties of the alloy were investigated. The alloy was composed of two primary body-centered cubic structures (BCC1 and BCC2) and a small amount of (Co, Cr)2Nb-type Laves phase under different annealing conditions. The microhardness and compressive strength of the heat-treated alloy was significantly enhanced by the solid-solution strengthening of the BCC phase matrix and newborn Laves phase. Especially, the alloy annealed at 1473 K (1200 °C) achieved the maximum hardness and compressive strength values of 959 ± 2 HV0.5 and 1790 MPa, respectively, owing to the enhanced volume fraction of the dispersed Laves phase. In particular, the HEAs exhibited promising high-temperature mechanical performance, when heated to an elevated temperature of 1473 K (1200 °C), with a compressive fracture strength higher than 580 MPa without fracture at a strain of more than 20 pct. This study suggests that the present refractory HEAs have immense potential for engineering applications as a new class of high-temperature structural materials.

Knock-Limited Performance of Triptane and Xylidines Blended with 28-R Aviation Fuel at High Compression Ratios and Maximum-Economy Spark Setting

NASA Technical Reports Server (NTRS)

Held, Louis F.; Pritchard, Ernest I.

1946-01-01

An investigation was conducted to evaluate the possibilities of utilizing the high-performance characteristics of triptane and xylidines blended with 28-R fuel in order to increase fuel economy by the use of high compression ratios and maximum-economy spark setting. Full-scale single-cylinder knock tests were run with 20 deg B.T.C. and maximum-economy spark settings at compression ratios of 6.9, 8.0, and 10.0, and with two inlet-air temperatures. The fuels tested consisted of triptane, four triptane and one xylidines blend with 28-R, and 28-R fuel alone. Indicated specific fuel consumption at lean mixtures was decreased approximately 17 percent at a compression ratio of 10.0 and maximum-economy spark setting, as compared to that obtained with a compression ratio of 6.9 and normal spark setting. When compression ratio was increased from 6.9 to 10.0 at an inlet-air temperature of 150 F, normal spark setting, and a fuel-air ratio of 0.065, 55-percent triptane was required with 28-R fuel to maintain the knock-limited brake power level obtained with 28-R fuel at a compression ratio of 6.9. Brake specific fuel consumption was decreased 17.5 percent at a compression ratio of 10.0 relative to that obtained at a compression ratio of 6.9. Approximately similar results were noted at an inlet-air temperature of 250 F. For concentrations up through at least 20 percent, triptane can be more efficiently used at normal than at maximum-economy spark setting to maintain a constant knock-limited power output over the range of compression ratios tested.

Brain metabolite changes in patients with type 2 diabetes and cerebral infarction using proton magnetic resonance spectroscopy.

PubMed

Zhang, Min; Sun, Xinhai; Zhang, Zhengjun; Meng, Qiang; Wang, Yuzhong; Chen, Jing; Ma, Xueqin; Geng, Houfa; Sun, Lin

2014-01-01

The aim of this study was to investigate the possible brain metabolic alterations in patients with type 2 diabetes mellitus (T2DM) and cerebral infarction (DMCI) using proton magnetic resonance spectroscopy (MRS). Thirty-four patients with T2DM and DMCI were scanned together with 33 patients with nondiabetic cerebral infarction (NDCI) on a 1.5-T MRI/MRS imager. Voxels were placed in the infarcted area and the contralateral normal area in the basal ganglia. N-acetylaspartate (NAA)/creatine (Cr), choline (Cho)/Cr, and lactate (Lac)/Cr ratios were calculated. Cerebral NAA/Cr ratios in the infarcted area were lower than those in the contralateral normal area of the NDCI group. There was a significant decrease in NAA/Cr in the infarcted area of the DMCI group as compared with the infarcted area of the NDCI group. NAA/Cr ratios in the contralateral normal area of DMCI group were lower than those of the NDCI group. Lac/Cr ratios were increased in the infarcted area of both the DMCI group and NDCI group, and Lac/Cr ratios tended to be higher in the infarcted area of the DMCI group than those of the NDCI group. Glycosylated hemoglobin (HbA1c) levels were negatively correlated with NAA/Cr ratios. The study suggested that the metabolite changes were different between DMCI patients and NDCI patients, which may provide important information in the treatment of DMCI.

Effects of stress ratio on the temperature-dependent high-cycle fatigue properties of alloy steels

NASA Astrophysics Data System (ADS)

Lü, Zhi-yang; Wan, Ao-shuang; Xiong, Jun-jiang; Li, Kuang; Liu, Jian-zhong

2016-12-01

This paper addresses the effects of stress ratio on the temperature-dependent high-cycle fatigue (HCF) properties of alloy steels 2CrMo and 9CrCo, which suffer from substantial vibrational loading at small stress amplitude, high stress ratio, and high frequency in the high-temperature environments in which they function as blade and rotor spindle materials in advanced gas or steam turbine engines. Fatigue tests were performed on alloy steels 2CrMo and 9CrCo subjected to constant-amplitude loading at four stress ratios and at four and three temperatures, respectively, to determine their temperature-dependent HCF properties. The interaction mechanisms between high temperature and stress ratio were deduced and compared with each other on the basis of the results of fractographic analysis. A phenomenological model was developed to evaluate the effects of stress ratio on the temperature-dependent HCF properties of alloy steels 2CrMo and 9CrCo. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Type I Cosmic Spherules: Key to a Major, But Poorly Sampled, Asteroid Population?

NASA Technical Reports Server (NTRS)

Nyquist, L. E.

1999-01-01

Herzog et al. have determined Fe, Ni, and Cr abundances in Type I cosmic spherules recovered from the deep sea, and also the isotopic fractionation of these elements during passage of the spherules through the terrestrial atmosphere. Isotopic fractionation for all three elements is typically large, approx. 16%/amu, corresponding to evaporative mass losses of approx. 80 - 85%, assuming Rayleigh distillation from an open system. The corrected, pre-atmospheric, Cr/Ni and Fe/Ni ratios, are compared to ratios in bulk chondrites and chondritic metal. Although the calculated pre-atmospheric Fe/Ni ratio for the spherules is relatively constant at 19 +/- 4 (sigma(sub mean)) the calculated pre-atmospheric Cr/Ni ratios vary by about two orders of magnitude. The Cr/Ni ratios are thus powerful discriminators for possible modes of origin of the spherules. For example, iron meteorites typically have low Cr contents and low Cr/Ni ratios, less or = 3 x 10(exp -4). Thus, Type I spherules do not appear to be ablation products of iron meteorites, in contrast to an earlier suggestion.

Estimation of Daily Proteinuria in Patients with Amyloidosis by Using the Protein-To-Creatinine ratio in Random Urine Samples.

PubMed

Talamo, Giampaolo; Mir Muhammad, A; Pandey, Manoj K; Zhu, Junjia; Creer, Michael H; Malysz, Jozef

2015-02-11

Measurement of daily proteinuria in patients with amyloidosis is recommended at the time of diagnosis for assessing renal involvement, and for monitoring disease activity. Renal involvement is usually defined by proteinuria >500 mg/day. We evaluated the accuracy of the random urine protein-to-creatinine ratio (Pr/Cr) in predicting 24 hour proteinuria in patient with amyloidosis. We compared results of random urine Pr/Cr ratio and concomitant 24-hour urine collections in 44 patients with amyloidosis. We found a strong correlation (Spearman's ρ=0.874) between the Pr/Cr ratio and the 24 hour urine protein excretion. For predicting renal involvement, the optimal cut-off point of the Pr/Cr ratio was 715 mg/g. The sensitivity and specificity for this point were 91.8% and 95.5%, respectively, and the area under the curve value was 97.4%. We conclude that the random urine Pr/Cr ratio could be useful in the screening of renal involvement in patients with amyloidosis. If validated in a prospective study, the random urine Pr/Cr ratio could replace the 24 hour urine collection for the assessment of daily proteinuria and presence of nephrotic syndrome in patients with amyloidosis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Lei; Wang, Shanmin; Zhu, Jinlong

Here, we report high-pressure synthesis of chromium monoboride (CrB) at 6 GPa and 1400 K. The elastic and plastic behaviors have been investigated by hydrostatic compression experiment and micro-indentation measurement. CrB is elastically incompressible with a high bulk modulus of 269.0 (5.9) GPa and exhibits a high Vickers hardness of 19.6 (0.7) GPa under the load of 1 kg force. Based on first principles calculations, the observed mechanical properties are attributed to the polar covalent Cr-B bonds interconnected with strong zigzag B-B covalent bonding network. The presence of metallic Cr bilayers is presumably responsible for the weakest paths in shearmore » deformation.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Lei; College of Construction Engineering, Jilin University, Changchun, Jilin 130061; Wang, Shanmin

We report high-pressure synthesis of chromium monoboride (CrB) at 6 GPa and 1400 K. The elastic and plastic behaviors have been investigated by hydrostatic compression experiment and micro-indentation measurement. CrB is elastically incompressible with a high bulk modulus of 269.0 (5.9) GPa and exhibits a high Vickers hardness of 19.6 (0.7) GPa under the load of 1 kg force. Based on first principles calculations, the observed mechanical properties are attributed to the polar covalent Cr-B bonds interconnected with strong zigzag B-B covalent bonding network. The presence of metallic Cr bilayers is presumably responsible for the weakest paths in shear deformation.

Investigation of mechanical properties for open cellular structure CoCrMo alloy fabricated by selective laser melting process

NASA Astrophysics Data System (ADS)

Azidin, A.; Taib, Z. A. M.; Harun, W. S. W.; Che Ghani, S. A.; Faisae, M. F.; Omar, M. A.; Ramli, H.

2015-12-01

Orthodontic implants have been a major focus through mechanical and biological performance in advance to fabricate shape of complex anatomical. Designing the part with a complex mechanism is one of the challenging process and addition to achieve the balance and desired mechanical performance brought to the right manufacture technique to fabricate. Metal additive manufacturing (MAM) is brought forward to the newest fabrication technology in this field. In this study, selective laser melting (SLM) process was utilized on a medical grade cobalt-chrome molybdenum (CoCrMo) alloy. The work has focused on mechanical properties of the CoCrMo open cellular structures samples with 60%, 70%, and 80% designed volume porosity that could potentially emulate the properties of human bone. It was observed that hardness values decreased as the soaking time increases except for bottom face. For compression test, 60% designed volume porosity demonstrated highest ultimate compressive strength compared to 70% and 80%.

Influence of fuel-nitrate ratio on the structural and magnetic properties of Fe and Cr based spinels prepared by solution self combustion method

NASA Astrophysics Data System (ADS)

Sijo, A. K.

2017-11-01

In this study, we report the synthesis of nano-sized CoCrFeO4 and NiCrFeO4 using the solution self combustion method and the variation in the magnetic and structural properties with different fuel to nitrate ratios-fuel lean, fuel rich and stoichiometric. Citric acid is used as the fuel. XRD analysis of the samples confirms the formation of pure spinel phased nanoparticles in fuel rich and stoichiometric cases. But CoCrFeO4 and NiCrFeO4 samples prepared under the fuel lean condition show the presence of a small amount of impurity phases: α-Ni in fuel lean NiCrFeO4 and α-Co in fuel lean CoCrFeO4. Fuel lean samples possess high magnetic saturation. The stoichiometric ratio results in finest nano-particles and structural and magnetic properties are very critically dependent on fuel to nitrate ratio.

Insular cortex metabolite changes in obstructive sleep apnea.

PubMed

Yadav, Santosh K; Kumar, Rajesh; Macey, Paul M; Woo, Mary A; Yan-Go, Frisca L; Harper, Ronald M

2014-05-01

Adults with obstructive sleep apnea (OSA) show significant autonomic and neuropsychologic deficits, which may derive from damage to insular regions that serve those functions. The aim was to assess glial and neuronal status from anterior insular metabolites in OSA versus controls, using proton magnetic resonance spectroscopy (PMRS), and thus to provide insights for neuroprotection against tissue changes, and to reduce injury consequences. Cross-sectional study. University-based medical center. Thirty-six patients with OSA, 53 controls. None. We performed PMRS in bilateral anterior insulae using a 3.0-Tesla magnetic resonance imaging scanner, calculated N-acetylaspartate/creatine (NAA/Cr), choline/creatine (Cho/Cr), myo-inositol/creatine (MI/Cr), and MI/NAA metabolite ratios, and examined daytime sleepiness (Epworth Sleepiness Scale, ESS), sleep quality (Pittsburgh Sleep Quality Index, PSQI), and neuropsychologic status (Beck Depression Inventory II [BDI-II] and Beck Anxiety Inventory [BAI]). Body mass index, BAI, BDI-II, PSQI, and ESS significantly differed between groups. NAA/ Cr ratios were significantly reduced bilaterally, and left-sided MI/Cr and MI/NAA ratios were increased in OSA over controls. Significant positive correlations emerged between left insular MI/Cr ratios and apnea-hypopnea index values, right insular Cho/Cr ratios and BDI-II and BAI scores, and negative correlations appeared between left insular NAA/Cr ratios and PSQI scores and between right-side MI/Cr ratios and baseline and nadir change in O2 saturation. Adults with obstructive sleep apnea showed bilaterally reduced N-acetylaspartate and left-side increased myo-inositol anterior insular metabolites, indicating neuronal damage and increased glial activation, respectively, which may contribute to abnormal autonomic and neuropsychologic functions in the condition. The activated glial status likely indicates increased inflammatory action that may induce more neuronal injury, and suggests separate approaches for glial and neuronal protection.

Growth performance and carcass characteristics of growing ram lambs fed sweet sorghum bagasse-based complete rations varying in roughage-to-concentrate ratios.

PubMed

Kumari, Nagireddy Nalini; Reddy, Yerradoddi Ramana; Blummel, Michel; Nagalakshmi, Devanaboyina; Monika, Thamatam; Reddy, Belum Venkata Subba; Reddy, Chintalapani Ravinder

2013-02-01

Different roughage-to-concentrate ratios of sweet sorghum bagasse (SSB) (a by-product of the biofuel industry)-based complete diets were assessed. Twenty four growing Nellore × Deccani ram lambs aged about 3 months (average body wt., 10.62 ± 0.25 kg) were randomly allotted to four complete rations (CR) varying in roughage-to-concentrate ratios viz. 60:40 (CR-I), 50:50 (CR-II), 40:60 (CR-III) and 30:70(CR-IV) for a period of 180 days. The feed intake was comparable among the lambs fed different experimental complete diets. Average daily weight gain (in grams) was 77.31 ± 4.90, 81.76 ± 5.16, 85.83 ± 2.83 and 86.30 ± 3.25, and feed conversion ratio (in kilograms of feed per kilogram gain) averaged 11.42 ± 0.68, 10.57 ± 0.64, 10.17 ± 0.37 and 9.96 ± 0.38 in ram lambs fed CR-I, CR-II, CR-III and CR-IV rations, respectively. Statistically, differences in daily weight gain and feed conversion ratio among the lambs fed four experimental rations were not significant (P > 0.05). The cost per kilogram gain was significantly (P < 0.01) higher in ram lambs fed CR-IV and CR-III rations compared to CR-I ration, and it was comparable between CR-I and CR-II rations. Dressing percentage averaged 44.90 ± 0.15, 42.57 ± 0.72, 43.67 ± 0.16 and 44.42 ± 0.76 for the respective diets. No significant difference and trend was observed in preslaughter weight, empty body weight, carcass weights, dressing percentage, wholesale cuts and edible and non-edible portions of experimental animals. Similarly, no significant variation could be seen in bone and meat yield (in per cent) and their ratios in various wholesale cuts among the dietary treatments. The roughage-to-concentrate ratio did not affect the chemical composition of meat; however, the fat content of meat was linearly increased with increase in the proportion of concentrate in the diets. The results of the experiment indicated that SSB can be included at 60 % level in the complete diet for economical mutton production from growing Nellore × Deccani ram lambs.

Structural behavior of ZnCr 2S 4 spinel under pressure

DOE PAGES

Efthimiopoulos, I.; Lochbiler, T.; Tsurkan, V.; ...

2016-12-15

Here, the series of Cr-chalcogenide spinels ACr 2X 4 (A = Zn, Cd, Hg; X = S, Se) exhibits a rich phase diagram upon compression, as revealed by our recent investigations. There exist, however, some open questions regarding the role of cations in the observed structural transitions. In order to address these queries, we have performed X-ray diffraction and Raman spectroscopic studies on the ZnCr 2S 4 spinel up to 42 GPa, chosen mainly due to the similarity of the Zn 2+ and Cr 3+ cationic radii. Two reversible structural transitions were identified at 22 and 33 GPa, into a I4 1/ amd and an orthorhombic phase, respectively. Close comparison with the behavior of relevant Cr-spinels revealed that the structural transitions are mainly governed by the competition of the magnetic exchange interactions present in these systems, and not by steric effects. In addition, careful inspection of the starting Fdmore » $$\\bar{3}$$m phase revealed a previously unnoticed isostructural transition. The latter is intimately related to changes in the electronic properties of these systems, as evidenced by our Raman studies. Our results provide insights for tuning the physical and chemical properties of these materials, even under moderate compression, as well as promoting the understanding of similar pressure-induced effects in relevant systems.« less

DNABIT Compress – Genome compression algorithm

PubMed Central

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-01

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, “DNABIT Compress” for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that “DNABIT Compress” algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases. PMID:21383923

Prediction of contrast-induced nephropathy in diabetic patients undergoing elective cardiac catheterization or PCI: role of volume-to-creatinine clearance ratio and iodine dose-to-creatinine clearance ratio.

PubMed

Worasuwannarak, Surapong; Pornratanarangsi, Suwatchai

2010-01-01

To assess a role of volume-to-creatinine clearance ratio (V/CrCl) and iodine dose-to-creatinine clearance ratio (I-dose/CrCl) in predicting contrast- induced nephropathy (CIN) in diabetic patients undergoing elective cardiac catheterization or percutaneous coronary intervention (PCI). In diabetic patients undergoing cardiac catheterization or PCI, the incidence of CIN is higher than in non-diabetic patients. High doses of contrast media also increase the likelihood of renal dysfunction. The ratio of the volume of contrast media to creatinine clearance (V/CrCl) and iodine dose-to-creatinine clearance (I-dose/CrCl) has been shown to correlate with the area under the curve of contrast media concentration over time and was used to predict the occurrence of CIN in unselected patients. No study has been conducted specifically in diabetic patients undergoing cardiac catheterization or PCI before. We conducted a prospective, single center study. The V/CrCl and I-dose/CrCl were calculated in diabetic patients undergoing elective cardiac catheterization or PCI. An increase in serum creatinine of > 0.5 mg/dl or > 25% by 7 days from baseline was considered CIN. The incidence of CIN was determined. The predictive value of V/CrCl and I-dose/CrCl for CIN were assessed using multivariable logistic regression. The total number of patients that had been enrolled in the study was 248; Male 50.8%. The overall incidence of CIN was 5.2%. The mean age for the entire population was 65 +/- 9 years; the mean body mass index was 25.6 +/- 4.0 kg/m2; and the mean creatinine clearance was 60.6 +/- 27.4 ml/min. The mean values of V/CrCl for patients with and without CIN were 3.7 +/- 2.9 and 2.2 +/- 1.7 (p = 0.041). The mean values of I-dose/CrCl for patients with and without CIN were 1.31 +/- 0.94 and 0.82 +/- 0.63 (p = 0.042). The receiver-operator characteristic curve analysis indicated that a V/CrCl ratio of 2.60 and I-dose/CrCl of 0.98 were fair predictors of CIN. After adjusting for other known predictors of CIN, a V/CrCl ratio > or = 2.60 remained the only significant predictor of CIN (Odds ratio 5.8; 95% confidence interval 1.7-19.4, p = 0.005). A V/CrCl ratio > or = 2.60 was a significant predictor of CIN in diabetic patients undergoing elective cardiac catheterization or PCI.

The effect on quality of chest compressions and exhaustion of a compression--ventilation ratio of 30:2 versus 15:2 during cardiopulmonary resuscitation--a randomised trial.

PubMed

Deschilder, Koen; De Vos, Rien; Stockman, Willem

2007-07-01

Recent cardio pulmonary resuscitation (CPR) guidelines changed the compression:ventilation ratio in 30:2. To compare the quality of chest compressions and exhaustion using the ratio 30:2 versus 15:2. A prospective, randomised crossover design was used. Subjects were recruited from the H.-Hart hospital personnel and the University College Katho for nurses and bio-engineering. Each participant performed 5min of CPR using either the ratio 30:2 or 15:2, then after a 15min rest switched to the other ratio. The data were collected using a questionnaire and an adult resuscitation manikin. The outcomes included exhaustion as measured by a visual analogue scale (VAS) score, depth of chest compressions, rates of chest compressions, total number of chest compressions, number of correct chest compressions and incomplete release. Data were compared using the Wilcoxon Signed Ranks Test. The results are presented as medians and interquartile ranges (IQR). One hundred and thirty subjects completed the study. The exhaustion-score using the VAS was 5.9 (IQR 2.25) for the ratio 30:2 and 4.5 (IQR 2.88) for the ratio 15:2 (P<0.001). The compression depth was 40.5mm (IQR 15.75) for 30:2 and 41mm (IQR 15.5) for 15:2 (P=0.5). The compression rate was 118beats/min (IQR 29) for 30:2 and 115beats/min (IQR 32) for 15:2 (P=0.02). The total number of compressions/5min was 347 (IQR 79) for 30:2 and 244compressions/5min (IQR 72.5) for 15:2 (P<0.001). The number of correct compression/5min was 61.5 (IQR 211.75) for 30:2 and 55.5 (IQR 142.75) for 15:2 (P=0.001). The relative risk (RR) of incomplete release in 30:2 versus 15:2 was 1.087 (95% CI=0.633-1.867). Although the 30:2 ratio is rated to be more exhausting, the 30:2 technique delivers more chest compressions and the quality of chest compressions remains unchanged.

Data Compression Techniques for Maps

DTIC Science & Technology

1989-01-01

Lempel - Ziv compression is applied to the classified and unclassified images as also to the output of the compression algorithms . The algorithms ...resulted in a compression of 7:1. The output of the quadtree coding algorithm was then compressed using Lempel - Ziv coding. The compression ratio achieved...using Lempel - Ziv coding. The unclassified image gave a compression ratio of only 1.4:1. The K means classified image

Evaluation of the Children's Eating Habits Questionnaire used in the IDEFICS study by relating urinary calcium and potassium to milk consumption frequencies among European children.

PubMed

Huybrechts, I; Börnhorst, C; Pala, V; Moreno, L A; Barba, G; Lissner, L; Fraterman, A; Veidebaum, T; Hebestreit, A; Sieri, S; Ottevaere, C; Tornaritis, M; Molnár, D; Ahrens, W; De Henauw, S

2011-04-01

Measuring dietary intake in children is notoriously difficult. Therefore, it is crucial to evaluate the performance of dietary intake assessment methods in children. Given the important contribution of milk consumption to calcium (Ca) and potassium (K) intakes, urinary calcium (UCa) and potassium (UK) excretions in spot urine samples could be used for estimating correlations with milk consumption frequencies. The aim of this study was to evaluate the assessment of milk consumption frequencies derived from the Food Frequency Questionnaire section of the Children's Eating Habits Questionnaire (CEHQ-FFQ) used in the IDEFICS (Identification and prevention of dietary- and lifestyle induced health effects in children and infants) study by comparing with UCa and UK excretions in spot urine samples. This study was conducted as a setting-based community-oriented intervention study and results from the first cross-sectional survey have been included in the analysis. A total of 10,309 children aged 2-10 years from eight European countries are included in this analysis. UCa and UK excretions were measured in morning spot urine samples. Calcium and potassium urine concentrations were standardised for urinary creatinine (Cr) excretion. Ratios of UCa/Cr and UK/Cr were used for multivariate regression analyses after logarithmic transformation to obtain normal distributions of data. Milk consumption frequencies were obtained from the CEHQ-FFQ. Multivariate regression analyses were used to investigate the effect of milk consumption frequencies on UCa and UK concentrations, adjusting for age, gender, study centre, soft drink consumption and frequency of main meals consumed at home. A significant positive correlation was found between milk consumption frequencies and ratios of UK/Cr and a weaker but still significant positive correlation with ratios of UCa/Cr, when using crude or partial Spearman's correlations. Multivariate regression analyses showed that milk consumption frequencies were predictive of UCa/Cr and UK/Cr ratios, when adjusted for age, gender, study centre, soft drink consumption and frequency of main meals consumed at home. Mean ratios of UK/Cr for increasing milk consumption frequency tertiles showed a progressive increase in UK/Cr. Children consuming at least two milk servings per day had significantly higher mean UCa/Cr and UK/Cr ratios than children who did not. Large differences in correlations between milk consumption frequencies and ratios of UCa/Cr and UK/Cr were found between the different study centres. Higher milk consumption frequencies resulted in a progressive increase in UK/Cr and UCa/Cr ratios, reflecting the higher Ca and K intakes that coincide with increasing milk consumption, which constitutes a major K and Ca source in children's diet.

Knock-Limited Performance of Triptane and 28-R Fuel Blends as Affected by Changes in Compression Ratio and in Engine Operating Variables

NASA Technical Reports Server (NTRS)

Brun, Rinaldo J.; Feder, Melvin S.; Fisher, William F.

1947-01-01

A knock-limited performance investigation was conducted on blends of triptane and 28-P fuel with a 12-cylinder, V-type, liquid-cooled aircraft engine of 1710-cubic-inch displacement at three compression ratios: 6.65, 7.93, and 9.68. At each compression ratio, the effect of changes in temperature of the inlet air to the auxiliary-stage supercharger and in fuel-air ratio were investigated at engine speeds of 2280 and. 3000 rpm. The results show that knock-limited engine performance, as improved by the use of triptane, allowed operation at both take-off and cruising power at a compression ratio of 9.68. At an inlet-air temperature of 60 deg F, an engine speed of 3000 rpm ; and a fuel-air ratio of 0,095 (approximately take-off conditions), a knock-limited engine output of 1500 brake horsepower was possible with 100-percent 28-R fuel at a compression ratio of 6.65; 20-percent triptane was required for the same power output at a compression ratio of 7.93, and 75 percent at a compression ratio of 9.68 allowed an output of 1480 brake horsepower. Knock-limited power output was more sensitive to changes in fuel-air ratio as the engine speed was increased from 2280 to 3000 rpm, as the compression ratio is raised from 6.65 to 9.68, or as the inlet-air temperature is raised from 0 deg to 120 deg F.

Estimation of Daily Proteinuria in Patients with Amyloidosis by Using the Protein-To-Creatinine ratio in Random Urine Samples

PubMed Central

Talamo, Giampaolo; Mir Muhammad, A.; Pandey, Manoj K.; Zhu, Junjia; Creer, Michael H.; Malysz, Jozef

2015-01-01

Measurement of daily proteinuria in patients with amyloidosis is recommended at the time of diagnosis for assessing renal involvement, and for monitoring disease activity. Renal involvement is usually defined by proteinuria >500 mg/day. We evaluated the accuracy of the random urine protein-to-creatinine ratio (Pr/Cr) in predicting 24 hour proteinuria in patient with amyloidosis. We compared results of random urine Pr/Cr ratio and concomitant 24-hour urine collections in 44 patients with amyloidosis. We found a strong correlation (Spearman’s ρ=0.874) between the Pr/Cr ratio and the 24 hour urine protein excretion. For predicting renal involvement, the optimal cut-off point of the Pr/Cr ratio was 715 mg/g. The sensitivity and specificity for this point were 91.8% and 95.5%, respectively, and the area under the curve value was 97.4%. We conclude that the random urine Pr/Cr ratio could be useful in the screening of renal involvement in patients with amyloidosis. If validated in a prospective study, the random urine Pr/Cr ratio could replace the 24 hour urine collection for the assessment of daily proteinuria and presence of nephrotic syndrome in patients with amyloidosis. PMID:25918613

Evaluation of Serum, Urine, and Hair Chromium Levels as Indices of Chromium Exposure and the Relationship of these Indices to Serum Lipid and Insulin Levels.

NASA Astrophysics Data System (ADS)

Randall, Janis Avril

Concentrations of chromium (Cr) in hair, serum, and urine, and serum concentrations of insulin and lipids of a selected group of men exposed to trivalent Cr (Cr III) were compared with those of men not exposed to Cr. Seventy -three tannery workers (TW) (mean age 37 +/- 12 years) from four Southern Ontario tanneries and fifty-two control subjects (CS) (mean age 41 +/- 13 years), matched for age, race, and socioeconomic status, from the Guelph and Toronto areas participated. The median hair and serum Cr concentrations for the TW were significantly higher (p < 0.01) than for the CS (hair Cr 453 vs 124 ng/g; serum Cr 0.49 vs 0.15 ng/ml). Median urinary Cr/creatinine ratios (Cr/Cre) for the TW on Monday morning (0.83 ng/mg) and Friday afternoon (0.68 ng/mg) were also significantly higher (p < 0.01, p < 0.01, respectively) than the median urinary Cr/Cre ratio for the urine samples collected on a Friday afternoon from the CS (0.18 ng/mg). For the TW, the median Friday urinary Cr/Cre ratio was significantly higher (p = 0.03) than the corresponding Monday Cr/Cre ratio. For the TW, urinary Cr/Cre ratios (Monday and Friday) were correlated significantly and positively with both Cr concentrations in serum (r = 0.45, p < 0.01; r = 0.71, p < 0.01, respectively) and in hair (r = 0.43, p < 0.01; r = 0.64, p < 0.01, respectively). Concentrations of Cr in hair and in serum were also significantly correlated (r = 0.52, p < 0.01). There were no significant differences between the TW and CS in serum concentrations of total cholesterol (TC), high-density lipoprotein cholesterol (HDL-C), or triglycerides, or in calculated values for low-density lipoprotein cholesterol, %HDL-C, and TC/HDL-C. Likewise, no significant differences in serum insulin concentrations were noted between the two groups. Results of this study indicate that Cr III, from compounds used in the leather tanning industry, is absorbed and retained. Absorption of Cr III had no significant effect on serum insulin concentrations or serum lipid profiles. These results also suggest that concentrations of Cr in hair, serum, and urine are valid biological indices of industrial exposure to Cr III.

FRESCO: Referential compression of highly similar sequences.

PubMed

Wandelt, Sebastian; Leser, Ulf

2013-01-01

In many applications, sets of similar texts or sequences are of high importance. Prominent examples are revision histories of documents or genomic sequences. Modern high-throughput sequencing technologies are able to generate DNA sequences at an ever-increasing rate. In parallel to the decreasing experimental time and cost necessary to produce DNA sequences, computational requirements for analysis and storage of the sequences are steeply increasing. Compression is a key technology to deal with this challenge. Recently, referential compression schemes, storing only the differences between a to-be-compressed input and a known reference sequence, gained a lot of interest in this field. In this paper, we propose a general open-source framework to compress large amounts of biological sequence data called Framework for REferential Sequence COmpression (FRESCO). Our basic compression algorithm is shown to be one to two orders of magnitudes faster than comparable related work, while achieving similar compression ratios. We also propose several techniques to further increase compression ratios, while still retaining the advantage in speed: 1) selecting a good reference sequence; and 2) rewriting a reference sequence to allow for better compression. In addition,we propose a new way of further boosting the compression ratios by applying referential compression to already referentially compressed files (second-order compression). This technique allows for compression ratios way beyond state of the art, for instance,4,000:1 and higher for human genomes. We evaluate our algorithms on a large data set from three different species (more than 1,000 genomes, more than 3 TB) and on a collection of versions of Wikipedia pages. Our results show that real-time compression of highly similar sequences at high compression ratios is possible on modern hardware.

Homogeneous and Heterogeneous (Fex, Cr1-x)(OH)3 Precipitation: Implications for Cr Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Chong; Zuo, Xiaobing; Cao, B

2016-02-16

The formation of (Fe, Cr)(OH)3 nanoparticles determines the fate of aqueous Cr in many aquatic environments. Using small angle X-ray scattering, precipitation rates of (Fe, Cr)(OH)3 nanoparticles in solution and on quartz were quantified from 0.1 mM Fe(III) solutions containing 0 – 0.25 mM Cr(III) at pH = 3.7 ± 0.2. Concentration ratio of aqueous Cr(III)/Fe(III) controlled the chemical composition (x) of (Fex, Cr1-x)(OH)3 precipitates, solutions’ supersaturation with respect to precipitates, and the surface charge of quartz. Therefore, aqueous Cr(III)/Fe(III) ratio affected homogeneous (in solution) and heterogeneous (on quartz) precipitation rates of (Fex, Cr1-x)(OH)3 through different mechanisms. The sequestration mechanismsmore » of Cr(III) in precipitates were also investigated. In solutions with high aqueous Cr(III)/Fe(III) ratios, surface enrichment of Cr(III) on the precipitates occurred, resulting in slower particle growth in solution. From solutions with 0 – 0.1 mM Cr(III), the particles on quartz grew from 2 to 4 nm within 1 h. Interestingly, from solution with 0.25 mM Cr(III), particles of two distinct sizes (2 and 6 nm) formed on quartz, and their sizes remained unchanged throughout the reaction. Our study provided new insights on homogeneous and heterogeneous precipitation of (Fex, Cr1-x)(OH)3 nanoparticles, which can help determine the fate of Cr in aquatic environments.« less

Hardness, elastic, and electronic properties of chromium monoboride

DOE PAGES

Han, Lei; Wang, Shanmin; Zhu, Jinlong; ...

2015-06-03

Here, we report high-pressure synthesis of chromium monoboride (CrB) at 6 GPa and 1400 K. The elastic and plastic behaviors have been investigated by hydrostatic compression experiment and micro-indentation measurement. CrB is elastically incompressible with a high bulk modulus of 269.0 (5.9) GPa and exhibits a high Vickers hardness of 19.6 (0.7) GPa under the load of 1 kg force. Based on first principles calculations, the observed mechanical properties are attributed to the polar covalent Cr-B bonds interconnected with strong zigzag B-B covalent bonding network. The presence of metallic Cr bilayers is presumably responsible for the weakest paths in shearmore » deformation.« less

Effect of heavy metals and water content on the strength of magnesium phosphate cements.

PubMed

Buj, Irene; Torras, Josep; Casellas, Daniel; Rovira, Miquel; de Pablo, Joan

2009-10-15

In this paper the mechanical properties of magnesium potassium phosphate cements used for the Stabilization/Solidification (S/S) of galvanic wastes were investigated. Surrogate wastes (metal nitrate dissolutions) were employed containing Cd, Cr(III), Cu, Ni, Pb or Zn at a concentration of 25 g dm(-3) and different water-to-solid (W/S) ratios (0.3, 0.4, 0.5 and 0.6 dm(3)kg(-1)) have been employed. Cements were prepared by mixing hard burned magnesia of about 70% purity with potassium dihydrogen phosphate. Compressive strength and tensile strength of specimens were determined. In addition the volume of permeable voids was measured. It was found that when comparing pastes that the volume of permeable voids increases and mechanical strength decreases with the increase of water-to-solid ratio (W/S). Nevertheless pastes with the same material proportions containing different metals show different mechanical strength values. The hydration products were analyzed by XRD. With the increase of water content not previously reported hydration compound was detected: bobierrite.

Day-to-day variation of urinary NGAL and rational for creatinine correction.

PubMed

Helmersson-Karlqvist, Johanna; Arnlöv, Johan; Larsson, Anders

2013-01-01

The number of clinical studies evaluating the new tubular biomarker urinary neutrophil gelatinase-associated lipocalin (U-NGAL) in urine are increasing. There is no consensus whether absolute U-NGAL concentrations or urinary NGAL/creatinine (U-NGAL/Cr) ratios should be used when chronic tubular dysfunction is studied. The aim was to study the biological variation of U-NGAL in healthy subjects and the rational for urinary creatinine (U-Cr) correction in two different study samples. To study biological variation of U-NGAL and U-NGAL/Cr ratio and the association between U-NGAL and U-Cr in healthy subjects 13 young males and females (median age 29 years) collected morning urine in 10 consecutive days. Additionally, a random subsample of 400 males from a population-based cohort (aged 78 years) collecting 24-hour urine during 1 day was studied. The calculated biological variation for absolute U-NGAL was 27% and for U-NGAL/Cr ratio, 101%. Absolute U-NGAL increased linearly with U-Cr concentration (the theoretical basis for creatinine adjustment) in the older males (R=0.19, P<0.001) and with borderline significance in the young adults (R=0.16, P=0.08). The U-NGAL/Cr ratio was, however, negatively associated with creatinine in the older males (R=-0.14, P<0.01) and in the young adults (R=-0.16, P=0.07) indicating a slight "overadjustment." The study provides some support for the use of U-NGAL/Cr ratio but the rather large biological variation and risk of possible overadjustment need to be considered. Both absolute U-NGAL and U-NGAL/Cr ratios should be reported for the estimation of chronic tubular dysfunction. Copyright © 2012 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Comparison of LCModel and SAGE in Analysis of Brain Metabolite Concentrations-A study of Patients with Mild Cognitive Impairment.

PubMed

Shih, Chiu-Ming; Lai, Jui-Jen; Chang, Chin-Ching; Chen, Cheng-Sheng; Yeh, Yi-Chun; Jaw, Twei-Shiun; Hsu, Jui-Sheng; Li, Chun-Wei

2017-03-15

The purpose of this study was to compare brain metabolite concentration ratios determined by LCModel and Spectroscopy Analysis by General Electric (SAGE) quantitative methods to elucidate the advantages and disadvantages of each method. A total of 10 healthy volunteers and 10 patients with mild cognitive impairment (MCI) were recruited in this study. A point-resolved spectroscopy (PRESS) sequence was used to obtain the brain magnetic resonance spectroscopy (MRS) spectra of the volunteers and patients, as well as the General Electric (GE) MRS-HD-sphere phantom. The brain metabolite concentration ratios were estimated based on the peak area obtained from both LCModel and SAGE software. Three brain regions were sampled for each volunteer or patient, and 20 replicates were acquired at different times for the phantom analysis. The metabolite ratios of the GE phantom were estimated to be myo-inositol (mI)/creatine (Cr): 0.70 ± 0.01, choline (Cho)/Cr: 0.37 ± 0.00, N-acetylaspartate (NAA)/Cr: 1.26 ± 0.02, and NAA/mI: 1.81 ± 0.04 by LCModel, and mI/Cr: 0.88 ± 0.15, Cho/Cr: 0.35 ± 0.01, NAA/Cr: 1.33 ± 0.03, and NAA/mI: 1.55 ± 0.26 by SAGE. In the healthy volunteers and MCI patients, the ratios of mI/Cr and Cho/Cr estimated by LCModel were higher than those estimated by SAGE. In contrast, the ratio of NAA/Cr estimated by LCModel was lower than that estimated by SAGE. Both methods were acceptable in estimating brain metabolite concentration ratios. However, LCModel was marginally more accurate than SAGE because of its full automation, basis set, and user independency.

Cryogenic Etching of High Aspect Ratio 400 nm Pitch Silicon Gratings.

PubMed

Miao, Houxun; Chen, Lei; Mirzaeimoghri, Mona; Kasica, Richard; Wen, Han

2016-10-01

The cryogenic process and Bosch process are two widely used processes for reactive ion etching of high aspect ratio silicon structures. This paper focuses on the cryogenic deep etching of 400 nm pitch silicon gratings with various etching mask materials including polymer, Cr, SiO 2 and Cr-on-polymer. The undercut is found to be the key factor limiting the achievable aspect ratio for the direct hard masks of Cr and SiO 2 , while the etch selectivity responds to the limitation of the polymer mask. The Cr-on-polymer mask provides the same high selectivity as Cr and reduces the excessive undercut introduced by direct hard masks. By optimizing the etching parameters, we etched a 400 nm pitch grating to ≈ 10.6 μ m depth, corresponding to an aspect ratio of ≈ 53.

Fuels for high-compression engines

NASA Technical Reports Server (NTRS)

Sparrow, Stanwood W

1926-01-01

From theoretical considerations one would expect an increase in power and thermal efficiency to result from increasing the compression ratio of an internal combustion engine. In reality it is upon the expansion ratio that the power and thermal efficiency depend, but since in conventional engines this is equal to the compression ratio, it is generally understood that a change in one ratio is accompanied by an equal change in the other. Tests over a wide range of compression ratios (extending to ratios as high as 14.1) have shown that ordinarily an increase in power and thermal efficiency is obtained as expected provided serious detonation or preignition does not result from the increase in ratio.

Minimum Specific Fuel Consumption of a Liquid-Cooled Multicylinder Aircraft Engine as Affected by Compression Ratio and Engine Operating Conditions

NASA Technical Reports Server (NTRS)

Brun, Rinaldo J.; Feder, Melvin S.; Harries, Myron L.

1947-01-01

An investigation was conducted on a 12-cylinder V-type liquid-cooled aircraft engine of 1710-cubic-inch displacement to determine the minimum specific fuel consumption at constant cruising engine speed and compression ratios of 6.65, 7.93, and 9.68. At each compression ratio, the effect.of the following variables was investigated at manifold pressures of 28, 34, 40, and 50 inches of mercury absolute: temperature of the inlet-air to the auxiliary-stage supercharger, fuel-air ratio, and spark advance. Standard sea-level atmospheric pressure was maintained at the auxiliary-stage supercharger inlet and the exhaust pressure was atmospheric. Advancing the spark timing from 34 deg and 28 deg B.T.C. (exhaust and intake, respectively) to 42 deg and 36 deg B.T.C. at a compression ratio of 6.65 resulted in a decrease of approximately 3 percent in brake specific fuel consumption. Further decreases in brake specific fuel consumption of 10.5 to 14.1 percent (depending on power level) were observed as the compression ratio was increased from 6.65 to 9.68, maintaining at each compression ratio the spark advance required for maximum torque at a fuel-air ratio of 0.06. This increase in compression ratio with a power output of 0.585 horsepower per cubic inch required a change from . a fuel- lend of 6-percent triptane with 94-percent 68--R fuel at a compression ratio of 6.65 to a fuel blend of 58-percent, triptane with 42-percent 28-R fuel at a compression ratio of 9.68 to provide for knock-free engine operation. As an aid in the evaluation of engine mechanical endurance, peak cylinder pressures were measured on a single-cylinder engine at several operating conditions. Peak cylinder pressures of 1900 pounds per square inch can be expected at a compression ratio of 9.68 and an indicated mean effective pressure of 320 pounds per square inch. The engine durability was considerably reduced at these conditions.

Edge-preserving image compression for magnetic-resonance images using dynamic associative neural networks (DANN)-based neural networks

NASA Astrophysics Data System (ADS)

Wan, Tat C.; Kabuka, Mansur R.

1994-05-01

With the tremendous growth in imaging applications and the development of filmless radiology, the need for compression techniques that can achieve high compression ratios with user specified distortion rates becomes necessary. Boundaries and edges in the tissue structures are vital for detection of lesions and tumors, which in turn requires the preservation of edges in the image. The proposed edge preserving image compressor (EPIC) combines lossless compression of edges with neural network compression techniques based on dynamic associative neural networks (DANN), to provide high compression ratios with user specified distortion rates in an adaptive compression system well-suited to parallel implementations. Improvements to DANN-based training through the use of a variance classifier for controlling a bank of neural networks speed convergence and allow the use of higher compression ratios for `simple' patterns. The adaptation and generalization capabilities inherent in EPIC also facilitate progressive transmission of images through varying the number of quantization levels used to represent compressed patterns. Average compression ratios of 7.51:1 with an averaged average mean squared error of 0.0147 were achieved.

Sign reversal of transformation entropy change in Co{sub 2}Cr(Ga,Si) shape memory alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Xiao, E-mail: xu@material.tohoku.ac.jp; Omori, Toshihiro; Kainuma, Ryosuke

2015-11-02

In situ X-ray diffraction (XRD) measurements and compression tests were performed on Co{sub 2}Cr(Ga,Si) shape memory alloys. The reentrant martensitic transformation behavior was directly observed during the in situ XRD measurements. The high-temperature parent phase and low-temperature reentrant parent phase were found to have a continuous temperature dependence of lattice parameter, therefore suggesting that they are the same phase in nature. Moreover, compression tests were performed on a parent-phase single crystal sample; an evolution from normal to inverse temperature dependence of critical stress for martensitic transformation was directly observed. Based on the Clausius-Clapeyron analysis, a sign reversal of entropy changemore » can be expected on the same alloy.« less

Effect of metal ratio and calcination temperature of chromium based mixed oxides catalyst on FAME density from palm fatty acid distillate

NASA Astrophysics Data System (ADS)

Wan, Z.; Fatimah, S.; Shahar, S.; Noor, A. C.

2017-09-01

Mixed oxides chromium based catalysts were synthesized via sol-gel method for the esterification of palm fatty acid distillate (PFAD) to produce fatty acid methyl ester (FAME). The reactions were conducted in a batch reactor at reaction temperature of 160 °C for 4 h and methanol to PFAD molar ratio of 3:1. The effects of catalyst preparation conditions which are the mixed metal ratio and calcination temperature were studied. The various metal ratio of Cr:Mn (1:0, 0:1, 1:1, 1:2 and 2:1) and Cr:Ti (0:1, 1:1, 1:2 and 2:1) resulted in FAME density ranges from 1.041 g/cm3 to 0.853 g/cm3 and 1.107 g/cm3 to 0.836 g/cm3, respectively. The best condition catalyst was found to be Cr:Ti metal ratio of 1:2 and Cr:Mn metal ratio of 1:1. The calcination temperature of the mixed oxides between 300 °C to 700°C shows effect on the FAME density obtained in the reaction. The calcination at 500°C gave the lowest FAME density of 0.836 g/cm3 and 0.853 g/cm3 for Cr:Ti and Cr:Mn mixed oxides, respectively. The density of FAME is within the value range of the biodiesel fuel property. Thus, mixed oxides of Cr-Ti and Cr-Mn have good potentials as heterogeneous catalyst for FAME synthesis from high acid value oils such as PFAD.

[Use of powder metallurgy for development of implants of Co-Cr-Mo alloy powder].

PubMed

Dabrowski, J R

2001-04-01

This paper discusses the application of powder metallurgy for the development of porous implantation materials. Powders obtained from Co-Cr-Mo alloy with different carbon content by water spraying and grinding, have been investigated. Cold pressing and rotary re-pressing methods were used for compressing the powder. It was found that the sintered materials obtained from water spraying have the most advantageous properties.

A Critical Proton MR Spectroscopy Marker of Alzheimer's Disease Early Neurodegenerative Change: Low Hippocampal NAA/Cr Ratio Impacts APOE ɛ4 Mexico City Children and Their Parents.

PubMed

Calderón-Garcidueñas, Lilian; Mora-Tiscareño, Antonieta; Melo-Sánchez, Gastón; Rodríguez-Díaz, Joel; Torres-Jardón, Ricardo; Styner, Martin; Mukherjee, Partha S; Lin, Weili; Jewells, Valerie

2015-01-01

Severe air pollution exposures produce systemic, respiratory, myocardial, and brain inflammation and Alzheimer's disease (AD) hallmarks in clinically healthy children. We tested whether hippocampal metabolite ratios are associated with contrasting levels of air pollution, APOE, and body mass index (BMI) in paired healthy children and one parent sharing the same APOE alleles. We used 1H-MRS to interrogate bilateral hippocampal single-voxel in 57 children (12.45 ± 3.4 years) and their 48 parents (37.5 ± 6.78 years) from a low pollution city versus Mexico City (MC). NAA/Cr, Cho/Cr, and mI/Cr metabolite ratios were analyzed. The right hippocampus NAA/Cr ratio was significantly different between cohorts (p = 0.007). The NAA/Cr ratio in right hippocampus in controls versus APOE ɛ4 MC children and in left hippocampus in MC APOE ɛ4 parents versus their children was significantly different after adjusting for age, gender, and BMI (p = 0.027 and 0.01, respectively). The NAA/Cr ratio is considered reflective of neuronal density/functional integrity/loss of synapses/higher pTau burden, thus a significant decrease in hippocampal NAA/Cr ratios may constitute a spectral marker of early neurodegeneration in young urbanites. Decreases in NAA/Cr correlate well with cognitive function, behavioral symptoms, and dementia severity; thus, since the progression of AD starts decades before clinical diagnosis, our findings support the hypothesis that under chronic exposures to fine particulate matter and ozone above the standards, neurodegenerative processes start in childhood and APOE ɛ4 carriers are at higher risk. Gene and environmental factors are critical in the development of AD and the identification and neuroprotection of young urbanites at high risk must become a public health priority.

Insular Cortex Metabolite Changes in Obstructive Sleep Apnea

PubMed Central

Yadav, Santosh K.; Kumar, Rajesh; Macey, Paul M.; Woo, Mary A.; Yan-Go, Frisca L.; Harper, Ronald M.

2014-01-01

Study Objective: Adults with obstructive sleep apnea (OSA) show significant autonomic and neuropsychologic deficits, which may derive from damage to insular regions that serve those functions. The aim was to assess glial and neuronal status from anterior insular metabolites in OSA versus controls, using proton magnetic resonance spectroscopy (PMRS), and thus to provide insights for neuroprotection against tissue changes, and to reduce injury consequences. Design: Cross-sectional study. Setting: University-based medical center. Participants: Thirty-six patients with OSA, 53 controls. Interventions: None. Measurements and Results: We performed PMRS in bilateral anterior insulae using a 3.0-Tesla magnetic resonance imaging scanner, calculated N-acetylaspartate/creatine (NAA/Cr), choline/creatine (Cho/Cr), myo-inositol/creatine (MI/Cr), and MI/NAA metabolite ratios, and examined daytime sleepiness (Epworth Sleepiness Scale, ESS), sleep quality (Pittsburgh Sleep Quality Index, PSQI), and neuropsychologic status (Beck Depression Inventory II [BDI-II] and Beck Anxiety Inventory [BAI]). Body mass index, BAI, BDI-II, PSQI, and ESS significantly differed between groups. NAA/ Cr ratios were significantly reduced bilaterally, and left-sided MI/Cr and MI/NAA ratios were increased in OSA over controls. Significant positive correlations emerged between left insular MI/Cr ratios and apnea-hypopnea index values, right insular Cho/Cr ratios and BDI-II and BAI scores, and negative correlations appeared between left insular NAA/Cr ratios and PSQI scores and between right-side MI/Cr ratios and baseline and nadir change in O2 saturation. Conclusions: Adults with obstructive sleep apnea showed bilaterally reduced N-acetylaspartate and left-side increased myo-inositol anterior insular metabolites, indicating neuronal damage and increased glial activation, respectively, which may contribute to abnormal autonomic and neuropsychologic functions in the condition. The activated glial status likely indicates increased inflammatory action that may induce more neuronal injury, and suggests separate approaches for glial and neuronal protection. Citation: Yadav SK, Kumar R, Macey PM, Woo MA, Yan-Go FL, Harper RM. Insular cortex metabolite changes in obstructive sleep apnea. SLEEP 2014;37(5):951-958. PMID:24790274

Influence of Compression Ratio on High Load Performance and Knock Behavior for Gasoline Port-Fuel Injection, Natural Gas Direct Injection and Blended Operation in a Spark Ignition Engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pamminger, Michael; Sevik, James; Scarcelli, Riccardo

Natural Gas (NG) is an alternative fuel which has attracted a lot of attention recently, in particular in the US due to shale gas availability. The higher hydrogen-to-carbon (H/C) ratio, compared to gasoline, allows for decreasing carbon dioxide emissions throughout the entire engine map. Furthermore, the high knock resistance of NG allows increasing the efficiency at high engine loads compared to fuels with lower knock resistance. NG direct injection (DI) allows for fuel to be added after intake valve closing (IVC) resulting in an increase in power density compared to an injection before IVC. Steady-state engine tests were performed onmore » a single-cylinder research engine equipped with gasoline (E10) port-fuel injection (PFI) and NG DI to allow for in-cylinder blending of both fuels. Knock investigations were performed at two discrete compression ratios (CR), 10.5 and 12.5. Operating conditions span mid-load, wide-open-throttle and boosted conditions, depending on the knock response of the fuel blend. Blended operation was performed using E10 gasoline and NG. An additional gasoline type fuel (E85) with higher knock resistance than E10 was used as a high-octane reference fuel, since the octane rating of E10-NG fuel blends is unknown. Spark timing was varied at different loads under stoichiometric conditions in order to study the knock response as well as the effects on performance and efficiency. As anticipated, results suggest that the knock resistance can be increased significantly by increasing the NG amount. Comparing the engine operation with the least knock resistant fuel, E10 PFI, and the fuel blend with the highest knock resistance, 75% NG DI, shows an increase in indicated mean effective pressure of about 9 bar at CR 12.5. The usage of reference fuels with known knock characteristics allowed an assessment of knock characteristic of intermediate E10-NG blend levels. Mathematical correlations were developed allowing characterizing the occurrence of knocking combustion by using the Livengood-Wu knock integral. For most of the fueling strategies and operating conditions, the mathematical correlations show good agreement when compared to experimental data.« less

Biaxial stress driven tetragonal symmetry breaking and high-temperature ferromagnetic semiconductor from half-metallic CrO2

NASA Astrophysics Data System (ADS)

Xiao, Xiang-Bo; Liu, Bang-Gui

2018-03-01

It is highly desirable to combine the full spin polarization of carriers with modern semiconductor technology for spintronic applications. For this purpose, one needs good crystalline ferromagnetic (or ferrimagnetic) semiconductors with high Curie temperatures. Rutile CrO2 is a half-metallic spintronic material with Curie temperature 394 K and can have nearly full spin polarization at room temperature. Here, we find through first-principles investigation that when a biaxial compressive stress is applied on rutile CrO2, the density of states at the Fermi level decreases with the in-plane compressive strain, there is a structural phase transition to an orthorhombic phase at the strain of -5.6 % , and then appears an electronic phase transition to a semiconductor phase at -6.1 % . Further analysis shows that this structural transition, accompanying the tetragonal symmetry breaking, is induced by the stress-driven distortion and rotation of the oxygen octahedron of Cr, and the half-metal-semiconductor transition originates from the enhancement of the crystal field splitting due to the structural change. Importantly, our systematic total-energy comparison indicates the ferromagnetic Curie temperature remains almost independent of the strain, near 400 K. This biaxial stress can be realized by applying biaxial pressure or growing the CrO2 epitaxially on appropriate substrates. These results should be useful for realizing full (100%) spin polarization of controllable carriers as one uses in modern semiconductor technology.

Etude de la structure électronique et magnétique de CrO_2

NASA Astrophysics Data System (ADS)

Matar, S.; Demazeau, G.; Sticht, J.; Eyert, V.; Kübler, J.

1992-03-01

The electronic and magnetic properties of CrO2 were investigated using the self-consistent A.S.W. method in a new approach to study the evolution of its magnetic properties at deceasing volume and to assess recent photoemission results on thin films. The results show that a magnetic transition of ferro Rightarrow antiferromagnetic type is likely to be induced under pressure. Experimental results could be explained by a compression of the CrO6 octahedron within the cell. Les propriétés électroniques de CrO2 ont été déterminées par la méthode auto-cohérente de l'onde sphérique augmentée : A.S.W. Cette étude est menée dans le cadre d'une nouvelle approche visant à définir lévolution de ses propriétés magnétiques à volume décroissant d'une part et à élucider les résultats expérimentaux récents de photoémission sur couches minces d'autre part. Les résultats des calculs montrent qu'une transition magnétique de type ferro Rightarrow antiferromagnétique est susceptible d'être induite sous l'effet de la pression. Les résultats expérimentaux pourraient être interprétés par une compression de l'octaèdre CrO6 au sein de la maille.

High load operation in a homogeneous charge compression ignition engine

DOEpatents

Duffy, Kevin P [Metamora, IL; Kieser, Andrew J [Morton, IL; Liechty, Michael P [Chillicothe, IL; Hardy, William L [Peoria, IL; Rodman, Anthony [Chillicothe, IL; Hergart, Carl-Anders [Peoria, IL

2008-12-23

A homogeneous charge compression ignition engine is set up by first identifying combinations of compression ratio and exhaust gas percentages for each speed and load across the engines operating range. These identified ratios and exhaust gas percentages can then be converted into geometric compression ratio controller settings and exhaust gas recirculation rate controller settings that are mapped against speed and load, and made available to the electronic

Characterization of hot bonding of bi-metal C45/25CrMo4 by plane strain compression test

NASA Astrophysics Data System (ADS)

Enaim, Mohammed; Langlois, Laurent; Zimmer-Chevret, Sandra; Bigot, Régis; Krumpipe, Pierre

2018-05-01

The need to produce multifunctional parts in order to conform to complex specifications becomes crucial in today's industrial context. This is why new processes are under study to develop multi-material parts which can satisfy this kind of requirements. This paper investigates the possibility of producing hot bonding of bi-metal C45/25CrMo4 parts by forging. This manufacturing process is a solid state joining process that involves, simultaneously, the welding and shaping of multi-material part. In this study, the C45/25CrMo4 bimetal was investigated. The forging is conducted at 1100°C and the influence of reduction rate on microstructure and bonding was investigated. The bonding model is inspired from Bay's model. Following this model, two parameters govern the solid-state bonding at the interface between materials: normal contact pressure and surface expansion. The objective is to check the bonding quality under different pressure and surface expansion. To achieve this goal, the plane strain compression test is chosen as the characterization test. Finally, simulations and experiments of this test are compared.

CrAlN coating to enhance the power loss and magnetostriction in grain oriented electrical steel

NASA Astrophysics Data System (ADS)

Goel, Vishu; Anderson, Philip; Hall, Jeremy; Robinson, Fiona; Bohm, Siva

2016-05-01

Grain oriented electrical steels (GOES) are coated with aluminium orthophosphate on top of a forsterite (Mg2SiO4) layer to provide stress and insulation resistance to reduce the power loss and magnetostriction. In this work Chromium Aluminium Nitride (CrAlN) was coated on GOES samples with electron beam physical vapour deposition and was tested in the single strip and magnetostriction tester to measure the power loss and magnetostriction before and after coating. Power loss was reduced by 2% after coating and 6 % post annealing at 800 °C. For applied compressive stress of 6 MPa, the magnetostrictive strain was zero with the CrAlN coating as compared to 22 and 24 μɛ for fully finished GOES and GOES without phosphate coating. The thickness of the coating was found to be 1.9 ± 0.2 μm estimated with Glow Discharge Optical Emission Spectroscopy (GDOES). The magnetic domain imaging showed domain narrowing after coating. The reduction in power loss and magnetostriction was due to the large residual compressive stress and Young's modulus (270 GPa) of the coating.

Similarities of biochemical abnormalities between major depressive disorder and bipolar depression: a proton magnetic resonance spectroscopy study.

PubMed

Zhong, Shuming; Wang, Ying; Zhao, Guoxiang; Xiang, Qi; Ling, Xueying; Liu, Sirun; Huang, Li; Jia, Yanbin

2014-10-01

Depression in the context of bipolar disorder (BD) is often misdiagnosed as major depressive disorder (MDD), leading to mistreatments and poor clinical outcomes for many bipolar patients. Previous neuroimaging studies found mixed results on brain structure, and biochemical metabolism of the two disorders. To eliminate the compounding effects of medication, and aging, this study sought to investigate the brain biochemical changes of treatment-naïve, non-late-life patients with MDD and BD in white matter in prefrontal (WMP) lobe, anterior cingulate cortex (ACC) and hippocampus by using proton magnetic resonance spectroscopy ((1)H-MRS). Three groups of participants were recruited: 26 MDD patients, 20 depressed BD patients, and 13 healthy controls. The multi-voxel (1)H-MRS [repetition time (TR)=1000ms; echo-time (TE)=144ms] was used for the measurement of N-acetylaspartate(NAA), choline containg compounds (Cho), and creatine (Cr) in three brain locations: white matter in prefrontal (WMP) lobe, anterior cingulate cortex (ACC), and hippocampus. Two ratios of NAA/Cr and Cho/Cr as a measure of brain biochemical changes were compared among three experimental groups. On the comparison of brain biochemical changes, both MDD patients and BD patients showed many similarities compared to the controls. They both had a significantly lower NAA/Cr ratio in the left WMP lobe. There were no significant differences among three experimental groups for Cho/Cr ratio in the WMP lobe, and for the ratios of NAA/Cr and Cho/Cr in the bilateral ACC and hippocampus. The only difference between MDD and BD patients existed for the NAA/Cr ratio in the right WMP lobe. While MDD patients had a significantly lower NAA/Cr ratio than controls, BD patients showed no such differences. On the comparison of correlation of medical variables and brain biochemical changes, all participants demonstrated no significant correlations. Reduced NAA/Cr ratio at the left WMP lobe indicated the dysfunction of neuronal viability in deep white matter, in both MDD and BD patients who shared similarities of brain biochemical abnormalities, which might imply an overlap in neuropathology of depression. Copyright © 2014 Elsevier B.V. All rights reserved.

Cardiac rehabilitation attendance and outcomes in coronary artery disease patients.

PubMed

Martin, Billie-Jean; Hauer, Trina; Arena, Ross; Austford, Leslie D; Galbraith, P Diane; Lewin, Adriane M; Knudtson, Merril L; Ghali, William A; Stone, James A; Aggarwal, Sandeep G

2012-08-07

Cardiac rehabilitation (CR) is an efficacious yet underused treatment for patients with coronary artery disease. The objective of this study was to determine the association between CR completion and mortality and resource use. We conducted a prospective cohort study of 5886 subjects (20.8% female; mean age, 60.6 years) who had undergone angiography and were referred for CR in Calgary, AB, Canada, between 1996 and 2009. Outcomes of interest included freedom from emergency room visits, hospitalization, and survival in CR completers versus noncompleters, adjusted for clinical covariates, treatment strategy, and coronary anatomy. Hazard ratios for events for CR completers versus noncompleters were also constructed. A propensity model was used to match completers to noncompleters on baseline characteristics, and each outcome was compared between propensity-matched groups. Of the subjects referred for CR, 2900 (49.3%) completed the program, and an additional 554 subjects started but did not complete CR. CR completion was associated with a lower risk of death, with an adjusted hazard ratio of 0.59 (95% confidence interval, 0.49-0.70). CR completion was also associated with a decreased risk of all-cause hospitalization (adjusted hazard ratio, 0.77; 95% confidence interval, 0.71-0.84) and cardiac hospitalization (adjusted hazard ratio, 0.68; 95% confidence interval, 0.55-0.83) but not with emergency room visits. Propensity-matched analysis demonstrated a persistent association between CR completion and reduced mortality. Among those coronary artery disease patients referred, CR completion is associated with improved survival and decreased hospitalization. There is a need to explore reasons for nonattendance and to test interventions to improve attendance after referral.

White matter NAA/Cho and Cho/Cr ratios at MR spectroscopy are predictive of motor outcome in preterm infants.

PubMed

Kendall, Giles S; Melbourne, Andrew; Johnson, Samantha; Price, David; Bainbridge, Alan; Gunny, Roxanna; Huertas-Ceballos, Angela; Cady, Ernest B; Ourselin, Sebastian; Marlow, Neil; Robertson, Nicola J

2014-04-01

To determine (a) whether diffuse white matter injury of prematurity is associated with an increased choline (Cho)-to-creatine (Cr) ratio and a reduced N-acetylaspartate (NAA)-to-Cho ratio and whether these measures can be used as biomarkers of outcome and (b) if changes in peak area metabolite ratios at magnetic resonance (MR) spectroscopy are associated with changes in T2 and fractional anisotropy (FA) at MR imaging. The local ethics committee approved this study, and informed parental consent was obtained for each infant. At term-equivalent age, 43 infants born at less than 32 weeks gestation underwent conventional and quantitative diffusion-tensor and T2-weighted MR imaging. Single-voxel point-resolved proton (hydrogen 1) MR spectroscopy was performed from a 2-cm(3) voxel centered in the posterior periventricular white matter. Outcome was evaluated by using Bayley scales at a corrected age of 1 year. Associations were investigated with Pearson product moment or Spearman rank order correlation. Differences in ratios in infants with and infants without impairment were tested by using t tests. NAA/Cho and Cho/Cr ratios correlated with the scaled gross motor score and the composite motor score, independent of gestational age (P < .05). FA at diffusion-tensor MR imaging and T2 at MR imaging correlated with the NAA/Cho ratio (P < .05 for both) but not with the Cho/Cr ratio. Infants with motor scores of less than 85 (impaired) had an increased Cho/Cr ratio (P < .03) and a reduced NAA/Cho ratio (P < .01) compared to those without impairment. A combination of increased Cho/Cr ratio and decreased NAA/Cho ratio predicted impaired motor outcome at a corrected age of 1 year with a sensitivity of 0.80 (95% confidence interval [CI]: 0.57, 0.94) and a specificity of 0.80 (95% CI: 0.66, 0.88). The combination of Cho/Cr and NAA/Cho ratios measured in the posterior periventricular white matter at term-equivalent age is predictive of motor outcome at 1 year in infants born at less than 32 weeks gestation. RSNA, 2013

Continuous manufacturing of extended release tablets via powder mixing and direct compression.

PubMed

Ervasti, Tuomas; Simonaho, Simo-Pekka; Ketolainen, Jarkko; Forsberg, Peter; Fransson, Magnus; Wikström, Håkan; Folestad, Staffan; Lakio, Satu; Tajarobi, Pirjo; Abrahmsén-Alami, Susanna

2015-11-10

The aim of the current work was to explore continuous dry powder mixing and direct compression for manufacturing of extended release (ER) matrix tablets. The study was span out with a challenging formulation design comprising ibuprofen compositions with varying particle size and a relatively low amount of the matrix former hydroxypropyl methylcellulose (HPMC). Standard grade HPMC (CR) was compared to a recently developed direct compressible grade (DC2). The work demonstrate that ER tablets with desired quality attributes could be manufactured via integrated continuous mixing and direct compression. The most robust tablet quality (weight, assay, tensile strength) was obtained using high mixer speed and large particle size ibuprofen and HPMC DC2 due to good powder flow. At low mixer speed it was more difficult to achieve high quality low dose tablets. Notably, with HPMC DC2 the processing conditions had a significant effect on drug release. Longer processing time and/or faster mixer speed was needed to achieve robust release with compositions containing DC2 compared with those containing CR. This work confirms the importance of balancing process parameters and material properties to find consistent product quality. Also, adaptive control is proven a pivotal means for control of continuous manufacturing systems. Copyright © 2015 Elsevier B.V. All rights reserved.

Compressive Behavior of Fiber-Reinforced Concrete with End-Hooked Steel Fibers.

PubMed

Lee, Seong-Cheol; Oh, Joung-Hwan; Cho, Jae-Yeol

2015-03-27

In this paper, the compressive behavior of fiber-reinforced concrete with end-hooked steel fibers has been investigated through a uniaxial compression test in which the variables were concrete compressive strength, fiber volumetric ratio, and fiber aspect ratio (length to diameter). In order to minimize the effect of specimen size on fiber distribution, 48 cylinder specimens 150 mm in diameter and 300 mm in height were prepared and then subjected to uniaxial compression. From the test results, it was shown that steel fiber-reinforced concrete (SFRC) specimens exhibited ductile behavior after reaching their compressive strength. It was also shown that the strain at the compressive strength generally increased along with an increase in the fiber volumetric ratio and fiber aspect ratio, while the elastic modulus decreased. With consideration for the effect of steel fibers, a model for the stress-strain relationship of SFRC under compression is proposed here. Simple formulae to predict the strain at the compressive strength and the elastic modulus of SFRC were developed as well. The proposed model and formulae will be useful for realistic predictions of the structural behavior of SFRC members or structures.

MP3 compression of Doppler ultrasound signals.

PubMed

Poepping, Tamie L; Gill, Jeremy; Fenster, Aaron; Holdsworth, David W

2003-01-01

The effect of lossy, MP3 compression on spectral parameters derived from Doppler ultrasound (US) signals was investigated. Compression was tested on signals acquired from two sources: 1. phase quadrature and 2. stereo audio directional output. A total of 11, 10-s acquisitions of Doppler US signal were collected from each source at three sites in a flow phantom. Doppler signals were digitized at 44.1 kHz and compressed using four grades of MP3 compression (in kilobits per second, kbps; compression ratios in brackets): 1400 kbps (uncompressed), 128 kbps (11:1), 64 kbps (22:1) and 32 kbps (44:1). Doppler spectra were characterized by peak velocity, mean velocity, spectral width, integrated power and ratio of spectral power between negative and positive velocities. The results suggest that MP3 compression on digital Doppler US signals is feasible at 128 kbps, with a resulting 11:1 compression ratio, without compromising clinically relevant information. Higher compression ratios led to significant differences for both signal sources when compared with the uncompressed signals. Copyright 2003 World Federation for Ultrasound in Medicine & Biology

Thermo-compressive transfer printing for facile alignment and robust device integration of nanowires.

PubMed

Lee, Won Seok; Won, Sejeong; Park, Jeunghee; Lee, Jihye; Park, Inkyu

2012-06-07

Controlled alignment and mechanically robust bonding between nanowires (NWs) and electrodes are essential requirements for reliable operation of functional NW-based electronic devices. In this work, we developed a novel process for the alignment and bonding between NWs and metal electrodes by using thermo-compressive transfer printing. In this process, bottom-up synthesized NWs were aligned in parallel by shear loading onto the intermediate substrate and then finally transferred onto the target substrate with low melting temperature metal electrodes. In particular, multi-layer (e.g. Cr/Au/In/Au and Cr/Cu/In/Au) metal electrodes are softened at low temperatures (below 100 °C) and facilitate submergence of aligned NWs into the surface of electrodes at a moderate pressure (∼5 bar). By using this thermo-compressive transfer printing process, robust electrical and mechanical contact between NWs and metal electrodes can be realized. This method is believed to be very useful for the large-area fabrication of NW-based electrical devices with improved mechanical robustness, electrical contact resistance, and reliability.

Study of Experiment on Rock-like Material Consist of fly-ash, Cement and Mortar

NASA Astrophysics Data System (ADS)

Nan, Qin; Hongwei, Wang; Yongyan, Wang

2018-03-01

Study the uniaxial compression test of rock-like material consist of coal ash, cement and mortar by changing the sand cement ratio, replace of fine coal, grain diameter, water-binder ratio and height-diameter ratio. We get the law of four factors above to rock-like material’s uniaxial compression characteristics and the quantitative relation. The effect law can be sum up as below: sample’s uniaxial compressive strength and elasticity modulus tend to decrease with the increase of sand cement ratio, replace of fine coal and water-binder ratio, and it satisfies with power function relation. With high ratio increases gradually, the uniaxial compressive strength and elastic modulus is lower, and presents the inverse function curve; Specimen tensile strength decreases gradually with the increase of fly ash. By contrast, uniaxial compression failure phenomenon is consistent with the real rock common failure pattern.

Performance of a Discrete Wavelet Transform for Compressing Plasma Count Data and its Application to the Fast Plasma Investigation on NASA's Magnetospheric Multiscale Mission

NASA Technical Reports Server (NTRS)

Barrie, Alexander C.; Yeh, Penshu; Dorelli, John C.; Clark, George B.; Paterson, William R.; Adrian, Mark L.; Holland, Matthew P.; Lobell, James V.; Simpson, David G.; Pollock, Craig J.;

Subjective evaluation of compressed image quality

NASA Astrophysics Data System (ADS)

Lee, Heesub; Rowberg, Alan H.; Frank, Mark S.; Choi, Hyung-Sik; Kim, Yongmin

1992-05-01

Lossy data compression generates distortion or error on the reconstructed image and the distortion becomes visible as the compression ratio increases. Even at the same compression ratio, the distortion appears differently depending on the compression method used. Because of the nonlinearity of the human visual system and lossy data compression methods, we have evaluated subjectively the quality of medical images compressed with two different methods, an intraframe and interframe coding algorithms. The evaluated raw data were analyzed statistically to measure interrater reliability and reliability of an individual reader. Also, the analysis of variance was used to identify which compression method is better statistically, and from what compression ratio the quality of a compressed image is evaluated as poorer than that of the original. Nine x-ray CT head images from three patients were used as test cases. Six radiologists participated in reading the 99 images (some were duplicates) compressed at four different compression ratios, original, 5:1, 10:1, and 15:1. The six readers agree more than by chance alone and their agreement was statistically significant, but there were large variations among readers as well as within a reader. The displacement estimated interframe coding algorithm is significantly better in quality than that of the 2-D block DCT at significance level 0.05. Also, 10:1 compressed images with the interframe coding algorithm do not show any significant differences from the original at level 0.05.

Metabolite differences in the lenticular nucleus in type 2 diabetes mellitus shown by proton MR spectroscopy.

PubMed

Lin, Y; Zhou, J; Sha, L; Li, Y; Qu, X; Liu, L; Chen, H; An, Z; Wang, Y; Sun, C

2013-09-01

Previous studies by using proton MR spectroscopy found metabolite abnormalities in the cerebral cortex and white matter of patients with type 2 diabetes mellitus. The present study was undertaken to detect metabolite differences in the lenticular nuclei and thalamus in patients with T2DM. Twenty subjects with T2DM and 22 age-matched control subjects underwent single-voxel MR spectroscopy in the left and right lenticular nuclei and left and right thalami. NAA/Cr and Cho/Cr ratios were calculated. Brain lactic acid, fasting blood glucose, and glycosylated hemoglobin levels were also monitored. The NAA/Cr ratio was lower in the left lenticular nuclei of subjects with T2DM (P = .007), whereas the Cho/Cr ratio was increased in both the and right lenticular nuclei (P = .001). The NAA/Cr ratio was negatively correlated with FBG in the left (r = -0.573, P = .008) and right nuclei (r = -0.564, P = .010). It was also negatively correlated to HbA1c in the left (r = -0.560, P = .010) and right (r = -0.453, P = .045) nuclei. The Cho/Cr ratio was positively correlated with these variables (P < .05). No significant differences in NAA/Cr or Cho/Cr ratios were observed in the thalamus of patients with T2DM. Lactic acid was not detected in any of the patients in the study. The different metabolic statuses of the lenticular nuclei and thalamus suggest different effects of T2DM in each of these brain nuclei, with the lenticular nuclei being more vulnerable than the thalamus. The abnormal metabolic status was observed before lesions had appeared in these brain areas.

Ion exchange separation of chromium from natural water matrix for stable isotope mass spectrometric analysis

USGS Publications Warehouse

Ball, J.W.; Bassett, R.L.

2000-01-01

A method has been developed for separating the Cr dissolved in natural water from matrix elements and determination of its stable isotope ratios using solid-source thermal-ionization mass spectrometry (TIMS). The separation method takes advantage of the existence of the oxidized form of Cr as an oxyanion to separate it from interfering cations using anion-exchange chromatography, and of the reduced form of Cr as a positively charged ion to separate it from interfering anions such as sulfate. Subsequent processing of the separated sample eliminates residual organic material for application to a solid source filament. Ratios for 53Cr/52Cr for National Institute of Standards and Technology Standard Reference Material 979 can be measured using the silica gel-boric acid technique with a filament-to-filament standard deviation in the mean 53Cr/52Cr ratio for 50 replicates of 0.00005 or less. (C) 2000 Elsevier Science B.V. All rights reserved.

The Mn-53-Cr-53 System in CAIs: An Update

NASA Technical Reports Server (NTRS)

Papanastassiou, D. A.; Wasserburg, G. J.; Bogdanovski, O.

2005-01-01

High precision techniques have been developed for the measurement of Cr isotopes on the Triton mass spectrometer, at JPL. It is clear that multiple Faraday cup, simultaneous ion collection may reduce the uncertainty of isotope ratios relative to single Faraday cup ion collection, by the elimination of uncertainties from ion beam instabilities (since ion beam intensities for single cup collection are interpolated in time to calculate isotope ratios), and due to a greatly increased data collection duty cycle, for simultaneous ion collection. Efforts to measure Cr by simultaneous ion collection have not been successful in the past. Determinations on Cr-50-54Cr, by simultaneous ion collection on the Finnigan/ MAT 262 instrument at Caltech, resulted in large variations in extrinsic precision, for normal Cr, of up to 1% in Cr-53/Cr-52 (data corrected for mass fractionation, using Cr-50/Cr-52).

The effect of changes in compression ratio upon engine performance

NASA Technical Reports Server (NTRS)

Sparrow, Stanwood W

1925-01-01

This report is based upon engine tests made at the Bureau of Standards during 1920, 1921, 1922, and 1923. The majority of these tests were of aviation engines and were made in the Altitude Laboratory. For a small portion of the work a single cylinder experimental engine was used. This, however, was operated only at sea-level pressures. The report shows that an increase in break horsepower and a decrease in the pounds of fuel used per brake horsepower hour usually results from an increase in compression ratio. This holds true at least up to the highest ratio investigated, 14 to 1, provided there is no serious preignition or detonation at any ratio. To avoid preignition and detonation when employing high-compression ratios, it is often necessary to use some fuel other than gasoline. It has been found that the consumption of some of these fuels in pounds per brake horsepower hour is so much greater than the consumption of gasoline that it offsets the decrease derived from the use of the high-compression ratio. The changes in indicated thermal efficiency with changes in compression ratio are in close agreement with what would be anticipated from a consideration of the air cycle efficiencies at the various ratios. In so far as these tests are concerned there is no evidence that a change in compression ratio produces an appreciable, consistent change in friction horsepower, volumetric efficiency, or in the range of fuel-air ratios over which the engine can operate. The ratio between the heat loss to the jacket water and the heat converted into brake horsepower or indicated horsepower decreases with increase in compression ratio. (author)

Proton Magnetic Resonance Spectroscopy Study on the Metabolism Changes of Cerebellum in Patients with Post-Stroke Depression.

PubMed

Zhang, Lei; Sui, Ru-Bo

2017-01-01

To study the metabolic changes of cerebellum by proton magnetic resonance Spectroscopy (1H-MRS) and discuss the relationships between the cerebellar changes and depression severity in patients with post-stroke depression. Data of demographic characteristics, individual history and life style of all subjects were collected. 40 patients with stroke and 20 controls were enrolled. All groups received T1WI, T2WI, DWI and 1H-MRS examination. The cerebral infarction volume and the distribution and severity of leukoaraiosis were evaluated. The ratios of NAA/Cr, Cho/Cr and Cho/NAA in the cerebellum were calculated. There were no statistical significant difference in the NAA/Cr, Cho/Cr and Cho/NAA ratios in bilateral cerebellum between CONT group and NORM group. The Cho/Cr and Cho/NAA ratios in the cerebellum contralateral to the stroke region were higher in PSD group than those in NORM and CONT groups, and the Cho/Cr and Cho/NAA ratios in the cerebellum ipsilateral to the stroke region were similar with those in NORM and CONT groups. However, there were no statistical significant difference in the NAA/Cr ratios in bilateral cerebellum among three groups. The result shows preliminarily that the cerebellum involves in the development of post-stroke depression. © 2017 The Author(s). Published by S. Karger AG, Basel.

The effect of organic compounds in the oxidation kinetics of Cr(III) by H 2O 2

NASA Astrophysics Data System (ADS)

Pettine, Maurizio; Gennari, Francesca; Campanella, Luigi; Millero, Frank J.

2008-12-01

The oxidation of Cr(III) has been studied in NaCl solutions in the presence of two siderophore models, acetohydroxamic acid (Aha) and benzohydroxamic acid (Bha), the natural siderophore Desferal (DFOB) and the synthetic aminocarboxilate (ethylenedinitrilo)-tetra-acetic acid (EDTA) as a function of pH (8-9), ionic strength (0.01-2 M) and temperature (10-50 °C), at different Cr(III)-organic compound ratios. The addition of Aha and Bha caused the rates to increase at low ligand/Cr(III) ratios and decrease at high ratios. The variation of the pseudo first order rate constant ( k1) as a function of the ligand concentration has been attributed to the formation of three Cr(III)-organo species (1:1, 1:2, 1:3), which can form in the presence of monohydroxamic acids. A kinetic model has been developed that gives a value of 600 (min -1) for the pseudo first order rate constant k and values approaching zero for k and k. These kinetic results demonstrate that these monohydroxamic acids are able to bind with Cr(III) under experimental conditions that may occur in natural waters and can increase the oxidation rates of Cr(III) with H 2O 2 by a factor of 3.5 at an Aha/Cr(III) ratio of about 50-100. The monohydroxamic acids also affect the rates on aged products of Cr(III), suggesting that these ligands are able to affect the oxidation rates by releasing reactive Cr(III). DFOB and EDTA do not have a great effect on the oxidation of Cr(III) with H 2O 2. This is thought to be due to the much longer times they need to form complexes with Cr(III) compared to Aha and Bha. The rates for the formation of DFOB and EDTA complexes with Cr(III) are not competitive with the rates of the formation of aged Cr(III). After allowing Cr(III) and DFOB to react for 5 days to form the complex, reaction rates of Cr(III) with H 2O 2 appear to be lowered probably because of steric hindrance of the chelated Cr(III).

Effect of raw material ratios on the compressive strength of magnesium potassium phosphate chemically bonded ceramics.

PubMed

Wang, Ai-juan; Yuan, Zhi-long; Zhang, Jiao; Liu, Lin-tao; Li, Jun-ming; Liu, Zheng

2013-12-01

The compressive strength of magnesium potassium phosphate chemically bonded ceramics is important in biomedical field. In this work, the compressive strength of magnesium potassium phosphate chemically bonded ceramics was investigated with different liquid-to-solid and MgO-to-KH2PO4 ratios. X-ray diffractometer was applied to characterize its phase composition. The microstructure was imaged using a scanning electron microscope. The results showed that the compressive strength of the chemically bonded ceramics increased with the decrease of liquid-to-solid ratio due to the change of the packing density and the crystallinity of hydrated product. However, with the increase of MgO-to-KH2PO4 weight ratio, its compressive strength increased firstly and then decreased. The low compressive strength in lower MgO-to-KH2PO4 ratio might be explained by the existence of the weak phase KH2PO4. However, the low value of compressive strength with the higher MgO-to-KH2PO4 ratio might be caused by lack of the joined phase in the hydrated product. Besides, it has been found that the microstructures were different in these two cases by the scanning electron microscope. Colloidal structure appeared for the samples with lower liquid-to-solid and higher MgO-to-KH2PO4 ratios possibly because of the existence of amorphous hydrated products. The optimization of both liquid-to-solid and MgO-to-KH2PO4 ratios was important to improve the compressive strength of magnesium potassium phosphate chemically bonded ceramics. © 2013.

Compression Ratio Adjuster

NASA Technical Reports Server (NTRS)

Akkerman, J. W.

1982-01-01

New mechanism alters compression ratio of internal-combustion engine according to load so that engine operates at top fuel efficiency. Ordinary gasoline, diesel and gas engines with their fixed compression ratios are inefficient at partial load and at low-speed full load. Mechanism ensures engines operate as efficiently under these conditions as they do at highload and high speed.

Compression behavior of quaternary and higher order solid-solution L1(2) trialuminides

NASA Technical Reports Server (NTRS)

Kumar, K. S.; Brown, S. A.

1992-01-01

Results from preliminary studies undertaken to evaluate the existence of single-phase L1(2) solid solutions between pairs of ternary L1(2) trialuminides are presented. Two-kilogram ingots of selected quaternary compositions were cast, homogenized and forged into pancakes; compression specimens were machined from the forgings and tested as a function of temperature. The results are compared against existing data for the ternary alloys. The ternary L1(2) trialuminides Al66Ti25Mn9, Al67Ti25Cr8, and Al22Ti8Fe3 were found to exhibit continuous solubility in one another. The quaternary Cr-Mn composition does not indicate any strength advantage over its ternary counterparts. The continuous replacement of Mn with Fe enhances the strength of the quaternary compound over the ternary Al66Ti25 Mn9.

Prediction of Fracture Initiation in Hot Compression of Burn-Resistant Ti-35V-15Cr-0.3Si-0.1C Alloy

NASA Astrophysics Data System (ADS)

Zhang, Saifei; Zeng, Weidong; Zhou, Dadi; Lai, Yunjin

2015-11-01

An important concern in hot working of metals is whether the desired deformation can be accomplished without fracture of the material. This paper builds a fracture prediction model to predict fracture initiation in hot compression of a burn-resistant beta-stabilized titanium alloy Ti-35V-15Cr-0.3Si-0.1C using a combined approach of upsetting experiments, theoretical failure criteria and finite element (FE) simulation techniques. A series of isothermal compression experiments on cylindrical specimens were conducted in temperature range of 900-1150 °C, strain rate of 0.01-10 s-1 first to obtain fracture samples and primary reduction data. Based on that, a comparison of eight commonly used theoretical failure criteria was made and Oh criterion was selected and coded into a subroutine. FE simulation of upsetting experiments on cylindrical specimens was then performed to determine the fracture threshold values of Oh criterion. By building a correlation between threshold values and the deforming parameters (temperature and strain rate, or Zener-Hollomon parameter), a new fracture prediction model based on Oh criterion was established. The new model shows an exponential decay relationship between threshold values and Zener-Hollomon parameter (Z), and the relative error of the model is less than 15%. This model was then applied successfully in the cogging of Ti-35V-15Cr-0.3Si-0.1C billet.

Evidence for a different electronic configuration as a primary effect during compression of orthorhombic perovskites: The case of Nd M3 +O3 (M =Cr ,Ga )

NASA Astrophysics Data System (ADS)

Ardit, M.; Dondi, M.; Merli, M.; Cruciani, G.

2018-02-01

(Mg ,Fe ) Si O3 perovskite is the most abundant mineral of the Earth's lower mantle, and compounds with the perovskite structure are perhaps the most widely employed ceramics. Hence, they attract both geophysicists and material scientists. Several investigations attempted to predict their structural evolution at high pressure, and recent advancements highlighted that perovskites having ions with the same formal valence at both polyhedral sites (i.e., 3 +:3 + ) define different compressional patterns when transition metal ions (TMI) are involved. In this study, in situ high-pressure synchrotron XRD measurements coupled with ab initio simulations of the electronic population of NdCr O3 perovskite are compared with the compressional feature of NdGa O3 . Almost identical from a steric point of view (C r3 + and G a3 + have almost the same ionic radius), the different electronic configuration of octahedrally coordinated ions - which leads to a redistribution of electrons at the 3 d orbitals for C r3 + - allows the crystal field stabilization energy (CFSE) to act as a vehicle of octahedral softening in NdCr O3 or it turns octahedra into rigid units when CFSE is null as in NdGa O3 . Besides to highlight that different electronic configurations can act as a primary effect during compression of perovskite compounds, our findings have a deep repercussion on the way the compressibility of perovskites have to be modeled.

Metabolite ratios to assumed stable creatine level may confound the quantification of proton brain MR spectroscopy.

PubMed

Li, Belinda S Y; Wang, Hao; Gonen, Oded

2003-10-01

In localized brain proton MR spectroscopy ((1)H-MRS), metabolites' levels are often expressed as ratios, rather than as absolute concentrations. Frequently, their denominator is the creatine [Cr], which level is explicitly assumed to be stable in normal as well as in many pathologic states. The rationale is that ratios self-correct for imager and localization method differences, gain instabilities, regional susceptibility variations and partial volume effects. The implicit assumption is that these benefits are worth their cost(w)-(w) propagation of the individual variation of each of the ratio's components. To test this hypothesis, absolute levels of N-acetylaspartate [NAA], choline [Cho] and [Cr] were quantified in various regions of the brains of 8 volunteers, using 3-dimensional (3D) (1)H-MRS at 1.5 T. The results show that in over 50% of approximately 2000 voxels examined, [NAA]/[Cr] and [Cho]/[Cr] exhibited higher coefficients of variations (CV) than [NAA] and [Cho] individually. Furthermore, in approximately 33% of these voxels, the ratios' CVs exceeded even the combined constituents' CVs. Consequently, basing metabolite quantification on ratios and assuming stable [Cr] introduces more variability into (1)H-MRS than it prevents. Therefore, its cost exceeds the benefit.

Measurement of urinary 11-dehydro-thromboxane B2 excretion in dogs with gastric dilatation-volvulus.

PubMed

Baltzer, Wendy I; McMichael, Maureen A; Ruaux, Craig G; Noaker, Laura; Steiner, Jörg M; Williams, David A

2006-01-01

To measure 11-dehydro-thromboxane B2 (11-dTXB2) in urine of healthy control dogs, dogs undergoing ovariohysterectomy, and dogs with gastric dilatation-volvulus (GDV) and assess the relationship between urinary 11-dTXB2 concentrations in dogs with GDV and postoperative outcomes. Urine samples from 15 nonsurgical control dogs, 12 surgical control dogs, and 32 dogs with GVD. Urine samples were obtained from healthy pet dogs (ie, nonsurgical control dogs), dogs undergoing ovariohysterectomy at anesthetic induction and 1 hour following surgery (ie, surgical control dogs), and dogs with GDV at hospital admission and 1 hour following surgical derotation of the stomach (ie, GDV dogs). Urinary 11-dTXB2 concentrations were determined with an ELISA and normalized to urinary creatinine (Cr) concentrations by calculation of the 11-dTXB2 -to-Cr ratio. Differences in median 11-dTXB2 -to-Cr ratios among dogs and before and after surgery were analyzed. Urinary 11-dTXB2-to-Cr ratios did not differ between nonsurgical control dogs and surgical control dogs before or after surgery. Urinary 11-dTXB2-to-Cr ratios were significantly higher in GDV dogs at the time of hospital admission and 1 hour after surgery, compared with those of nonsurgical control dogs. Postoperative urine samples from GDV dogs had significantly higher 11-dTXB2-to-Cr ratios than postoperative urine samples from surgical control dogs. Median urinary 11-dTXB2-to-Cr ratios increased significantly in GDV dogs that developed postoperative complications. Urinary 11-dTXB2 concentration is increased in GDV dogs at the time of hospital admission and after surgical derotation of the stomach, compared with that of healthy dogs. An increased urinary 11-dTXB2-to-Cr ratio following surgery is associated with an increased incidence of postoperative complications in dogs with GDV.

Glutamate-glutamine and GABA in brain of normal aged and patients with cognitive impairment.

PubMed

Huang, Dandan; Liu, Dan; Yin, Jianzhong; Qian, Tianyi; Shrestha, Susan; Ni, Hongyan

2017-07-01

To explore the changes of glutamate-glutamine (Glx) and gamma-aminobutyric acid (GABA) in the brain in normal old age and cognitive impairment using magnetic resonance spectroscopy (MRS). Seventeen normal young controls (NYC), 15 normal elderly controls (NEC), 21 patients with mild cognitive impairment (MCI) and 17 with Alzheimer disease (AD) patients were included in this study. Glx and GABA+ levels in the anterior cingulate cortex (ACC) and right hippocampus (rHP) were measured by using a MEGA-PRESS sequence. Glx/Cr and GABA+/Cr ratios were compared between NYC and NEC and between the three elderly groups using analysis of covariance (ANCOVA); the tissue fractions of voxels were used as covariates. The relationships between metabolite ratios and cognitive performance were analysed using Spearman correlation coefficients. For NEC and NYC groups, Glx/Cr and GABA+/Cr ratios were lower in NEC in ACC and rHP. For the three elderly groups, Glx/Cr ratio was lower in AD in ACC compared to NEC and MCI; Glx/Cr ratio was lower in AD in rHP compared to NEC. There was no significant decrease for GABA+/Cr ratio. Glx and GABA levels may decrease simultaneously in normal aged, and Glx level decreased predominantly in AD, and it is helpful in the early diagnosis of AD. • Glx and GABA levels may decrease simultaneously in normal aged. • Glx level may decrease predominantly in Alzheimer disease. • The balance in excitatory-inhibitory systems may be broken in AD. • Decreased Glx level may be helpful in early diagnosis of AD.

Accuracy and equivalence testing of crown ratio models and assessment of their impact on diameter growth and basal area increment predictions of two variants of the Forest Vegetation Simulator

Treesearch

Laura P. Leites; Andrew P. Robinson; Nicholas L. Crookston

2009-01-01

Diameter growth (DG) equations in many existing forest growth and yield models use tree crown ratio (CR) as a predictor variable. Where CR is not measured, it is estimated from other measured variables. We evaluated CR estimation accuracy for the models in two Forest Vegetation Simulator variants: the exponential and the logistic CR models used in the North...

Hippocampal metabolic dysfunction in juvenile myoclonic epilepsy: 3D multivoxel spectroscopy study.

PubMed

Ristić, Aleksandar J; Ostojić, Jelena; Kozić, Duško; Vojvodić, Nikola M; Popović, Ljubica M; Janković, Slavko; Baščarević, Vladimir; Sokić, Dragoslav V

2011-06-15

To investigate the metabolic differences in hippocampi of patients with juvenile myoclonic epilepsy (JME) and healthy controls using magnetic resonance spectroscopy (MRS). A 3D multivoxel SE 135 MRS study on 1.5 T scanner of both hippocampi was performed in 17 patients with JME and normal brain MRI and in 19 age and sex matched controls. Three dominant signals were measured: Choline (Cho), Creatine (tCr) and N-Acetylaspartate (NAA) and expressed as ratios of Cho:tCr, NAA:tCr, NAA:Cho and NAA:(Cho+tCr). Metabolite ratios in head, body and tail of each hippocampus in the JME group of patients were compared with ratios from corresponding structures in the control group. We found a significant difference in metabolite ratios of both hippocampi between the JME and the control groups. We detected significant differences of Cho:tCr in the head, NAA:tCr in the head, body and tail, NAA:Cho and NAA:(Cho+tCr) in the body and tail of the left hippocampus, and NAA:Cho and NAA:(Cho+tCr) in the body and tail of the right hippocampus. Although not previously recognized as a part of the epileptogenic network, our results suggest that the hippocampus, well recognized as a key player in focal epilepsies, may have a certain role in the pathogenesis of JME. Copyright © 2010. Published by Elsevier B.V.

Beryl-II, a high-pressure phase of beryl: Raman and luminescence spectroscopy to 16.4 GPa

NASA Astrophysics Data System (ADS)

O'Bannon, Earl; Williams, Quentin

2016-10-01

The Raman and Cr3+ and V2+ luminescence spectra of beryl and emerald have been characterized up to 15.0 and 16.4 GPa, respectively. The Raman spectra show that an E 1g symmetry mode at 138 cm-1 shifts negatively by -4.57 (±0.55) cm-1/GPa, and an extrapolation of the pressure dependence of this mode indicates that a soft-mode transition should occur near 12 GPa. Such a transition is in accord with prior theoretical results. Dramatic changes in Raman mode intensities and positions occur between 11.2 and 15.0 GPa. These changes are indicative of a phase transition that primarily involves tilting and mild distortion of the Si6O18 rings. New Raman modes are not observed in the high-pressure phase, which indicates that the local bonding environment is not altered dramatically across the transition (e.g., changes in coordination do not occur). Both sharp line and broadband luminescence are observed for both Cr3+ and V2+ in emerald under compression to 16.4 GPa. The R-lines of both Cr3+ and V2+ shift to lower energy (longer wavelength) under compression. Both R-lines of Cr3+ split at ~13.7 GPa, and the V2+ R1 slope changes at this pressure and shifts more rapidly up to ~16.4 GPa. The Cr3+ R-line splitting and FWHM show more complex behavior, but also shift in behavior at ~13.7 GPa. These changes in the pressure dependency of the Cr3+ and V2+ R-lines and the changes in R-line splitting and FWHM at ~13.7 GPa further demonstrate that a phase transition occurs at this pressure, in good agreement with our Raman results. The high-pressure phase of beryl appears to have two Al sites that become more regular under compression. Hysteresis is not observed in our Raman or luminescence spectra on decompression, suggesting that this transition is second order in nature: The occurrence of a second-order transition near this pressure is also in accord with prior theoretical results. We speculate that the high-pressure phase (beryl-II) might be a mildly modulated structure, and/or that extensive twinning occurs across this transition.

Performance and exhaust emission characteristics of variable compression ratio diesel engine fuelled with esters of crude rice bran oil.

PubMed

Vasudeva, Mohit; Sharma, Sumeet; Mohapatra, S K; Kundu, Krishnendu

2016-01-01

As a substitute to petroleum-derived diesel, biodiesel has high potential as a renewable and environment friendly energy source. For petroleum importing countries the choice of feedstock for biodiesel production within the geographical region is a major influential factor. Crude rice bran oil is found to be good and viable feedstock for biodiesel production. A two step esterification is carried out for higher free fatty acid crude rice bran oil. Blends of 10, 20 and 40 % by vol. crude rice bran biodiesel are tested in a variable compression ratio diesel engine at compression ratio 15, 16, 17 and 18. Engine performance and exhaust emission parameters are examined. Cylinder pressure-crank angle variation is also plotted. The increase in compression ratio from 15 to 18 resulted in 18.6 % decrease in brake specific fuel consumption and 14.66 % increase in brake thermal efficiency on an average. Cylinder pressure increases by 15 % when compression ratio is increased. Carbon monoxide emission decreased by 22.27 %, hydrocarbon decreased by 38.4 %, carbon dioxide increased by 17.43 % and oxides of nitrogen as NOx emission increased by 22.76 % on an average when compression ratio is increased from 15 to 18. The blends of crude rice bran biodiesel show better results than diesel with increase in compression ratio.

Effects of electroacupuncture on metabolic changes in motor cortex and striatum of 6-hydroxydopamine-induced Parkinsonian rats.

PubMed

Li, Min; Wang, Ke; Su, Wen-Ting; Jia, Jun; Wang, Xiao-Min

2017-10-06

To explore the possible underlying mechanism by investigating the effect of electroacupuncture (EA) treatment on the primary motor cortex and striatum in a unilateral 6-hydroxydopamine (6-OHDA) induced rat Parkinson's disease (PD) model. Male Sprague-Dawley rats were randomly divided into sham group (n=16), model group (n=14), and EA group (n=14). EA stimulation at Dazhui (GV 14) and Baihui (GV20) was applied to PD rats in the EA group for 4 weeks. Behavioral tests were conducted to evaluate the effectiveness of EA treatment. Metabolites were detected by 7.0 T proton nuclear magnetic resonance. Following 4 weeks of EA treatment in PD model rats, the abnormal behavioral impairment induced by 6-OHDA was alleviated. In monitoring changes in metabolic activity, ratios of myoinositol/creatine (Cr) and N-acetyl aspartate (NAA)/Cr in the primary motor cortex were significantly lower at the injected side than the non-injected side in PD rats (P=0.024 and 0.020). The ratios of glutamate + glutamine (Glx)/Cr and NAA/Cr in the striatum were higher and lower, respectively, at the injected side than the non-injected side (P=0.046 and 0.008). EA treatment restored the balance of metabolic activity in the primary motor cortex and striatum. In addition, the taurine/Cr ratio and Glx/Cr ratio were elevated in the striatum of PD model rats compared to sham-lesioned rats (P=0.026 and 0.000). EA treatment alleviated the excessive glutamatergic transmission by down-regulating the striatal Glx/Cr ratio (P=0.001). The Glx/Cr ratio was negatively correlated with floor plane spontaneous locomotion in PD rats (P=0.027 and P=0.0007). EA treatment is able to normalize the metabolic balance in the primary motor cortex and striatum of PD rats, which may contribute to its therapeutic effect on motor deficits. The striatal Glx/Cr ratio may serve as a potential indicator of PD and a therapeutic target of EA treatment.

Effect of alkaline precipitation on Cr species of Cr(III)-bearing complexes typically used in the tannery industry.

PubMed

Wang, Dandan; Ye, Yuxuan; Liu, Hui; Ma, Hongrui; Zhang, Weiming

2018-02-01

Various organic compounds extensively used in the leather industry could influence the performance of alkaline precipitation with Cr(III). This study focused on two typical Cr(III)-bearing complexes (Cr(III)-collagen and Cr(III)-citrate) ubiquitous in tannery effluent yet with distinct treatment efficiencies, as Cr(III) was much more difficult to remove in the Cr(III)-citrate solution. Comprehensive analytical methods were employed to explore the intrinsic mechanism. It was found that a lower removal efficiency towards Cr(III) was significantly associated with higher oligomers. The molecular size of the Cr(III)-citrate complex continued to increase with rising pH, making it larger overall than Cr(III)-collagen species. The growing oligomer moiety of dissolved Cr(III)-complex species could persist in the stronger basic pH range, leading to the large amount of residual Cr(III) in the Cr(III)-citrate system. Combining this result with potentiometric titration and X-ray photoelectron spectroscopy data, it was believed that the polymeric species other than monomers facilitated resisting the attack from hydroxide ions, and the postulated Cr(III)-citrate species towards higher oligomers were discovered. Beyond that, both charge neutralization and sweeping effects were presented among the gradually emerging flocs in the Cr(III)-collagen system together with the electric double layer compression effect derived from salinity, thus resulting in a larger floc size and higher Cr(III) removal efficiency in saline solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Compressive Behavior of Fiber-Reinforced Concrete with End-Hooked Steel Fibers

PubMed Central

Lee, Seong-Cheol; Oh, Joung-Hwan; Cho, Jae-Yeol

2015-01-01

In this paper, the compressive behavior of fiber-reinforced concrete with end-hooked steel fibers has been investigated through a uniaxial compression test in which the variables were concrete compressive strength, fiber volumetric ratio, and fiber aspect ratio (length to diameter). In order to minimize the effect of specimen size on fiber distribution, 48 cylinder specimens 150 mm in diameter and 300 mm in height were prepared and then subjected to uniaxial compression. From the test results, it was shown that steel fiber-reinforced concrete (SFRC) specimens exhibited ductile behavior after reaching their compressive strength. It was also shown that the strain at the compressive strength generally increased along with an increase in the fiber volumetric ratio and fiber aspect ratio, while the elastic modulus decreased. With consideration for the effect of steel fibers, a model for the stress–strain relationship of SFRC under compression is proposed here. Simple formulae to predict the strain at the compressive strength and the elastic modulus of SFRC were developed as well. The proposed model and formulae will be useful for realistic predictions of the structural behavior of SFRC members or structures. PMID:28788011

The compression and storage method of the same kind of medical images: DPCM

NASA Astrophysics Data System (ADS)

Zhao, Xiuying; Wei, Jingyuan; Zhai, Linpei; Liu, Hong

2006-09-01

Medical imaging has started to take advantage of digital technology, opening the way for advanced medical imaging and teleradiology. Medical images, however, require large amounts of memory. At over 1 million bytes per image, a typical hospital needs a staggering amount of memory storage (over one trillion bytes per year), and transmitting an image over a network (even the promised superhighway) could take minutes--too slow for interactive teleradiology. This calls for image compression to reduce significantly the amount of data needed to represent an image. Several compression techniques with different compression ratio have been developed. However, the lossless techniques, which allow for perfect reconstruction of the original images, yield modest compression ratio, while the techniques that yield higher compression ratio are lossy, that is, the original image is reconstructed only approximately. Medical imaging poses the great challenge of having compression algorithms that are lossless (for diagnostic and legal reasons) and yet have high compression ratio for reduced storage and transmission time. To meet this challenge, we are developing and studying some compression schemes, which are either strictly lossless or diagnostically lossless, taking advantage of the peculiarities of medical images and of the medical practice. In order to increase the Signal to Noise Ratio (SNR) by exploitation of correlations within the source signal, a method of combining differential pulse code modulation (DPCM) is presented.

Chromium isotopic homogeneity between the Moon, the Earth, and enstatite chondrites

NASA Astrophysics Data System (ADS)

Mougel, Bérengère; Moynier, Frédéric; Göpel, Christa

2018-01-01

Among the elements exhibiting non-mass dependent isotopic variations in meteorites, chromium (Cr) has been central in arguing for an isotopic homogeneity between the Earth and the Moon, thus questioning physical models of Moon formation. However, the Cr isotopic composition of the Moon relies on two samples only, which define an average value that is slightly different from the terrestrial standard. Here, by determining the Cr isotopic composition of 17 lunar, 9 terrestrial and 5 enstatite chondrite samples, we re-assess the isotopic similarity between these different planetary bodies, and provide the first robust estimate for the Moon. In average, terrestrial and enstatite samples show similar ε54Cr. On the other hand, lunar samples show variables excesses of 53Cr and 54Cr compared to terrestrial and enstatite chondrites samples with correlated ε53Cr and ε54Cr (per 10,000 deviation of the 53Cr/52Cr and 54Cr/52Cr ratios normalized to the 50Cr/52Cr ratio from the NIST SRM 3112a Cr standard). Unlike previous suggestions, we show for the first time that cosmic irradiation can affect significantly the Cr isotopic composition of lunar materials. Moreover, we also suggest that rather than spallation reactions, neutron capture effects are the dominant process controlling the Cr isotope composition of lunar igneous rocks. This is supported by the correlation between ε53Cr and ε54Cr, and 150Sm/152Sm ratios. After correction of these effects, the average ε54Cr of the Moon is indistinguishable from the terrestrial and enstatite chondrite materials reinforcing the idea of an Earth-Moon-enstatite chondrite system homogeneity. This is compatible with the most recent scenarios of Moon formation suggesting an efficient physical homogenization after a high-energy impact on a fast spinning Earth, and/or with an impactor originating from the same reservoir in the inner proto-planetary disk as the Earth and enstatite chondrites and having similar composition.

An investigation of the effect of aspect and compression ratios on sediment dispersion using discrete element modelling

NASA Astrophysics Data System (ADS)

Wang, Dong; Tan, Danielle S.

2017-12-01

We use discrete element modelling to simulate a system of sand being released underwater, similar to the process of releasing sediment tailings back into the sea in nodule harvesting, in 2D. The force model includes concentration-dependent drag, buoyancy, `added mass' and Stokeslet disturbance. For a fixed number of uniform-sized particles, we vary the aspect ratio and the compression ratio of the rectangular mass of granular media pre-release. We observed that the spreading leads to a nonlinear increase with aspect ratio. On the other hand, when the compression ratio is increased, the total spreading increases; however the spread of the bulk of the sand decreases at small aspect ratios and increases at large aspect ratios. We proposed a simple theoretical model for the horizontal spreading which depends on both the aspect and compression ratios.

Diagnostic quality of 50 and 100 µm computed radiography compared with screen–film mammography in operative breast specimens

PubMed Central

Pagliari, C M; Hoang, T; Reddy, M; Wilkinson, L S; Poloniecki, J D; Given-Wilson, R M

2012-01-01

Objective To compare reader ratings of the clinical diagnostic quality of 50 and 100 μm computed radiography (CR) systems with screen–film mammography (SFM) in operative specimens. Methods Mammograms of 57 fresh operative breast specimens were analysed by 10 readers. Exposures were made with identical position and compression with three mammographic systems (Fuji 100CR, 50CR and SFM). Images were anonymised and readers blinded to the CR system used. A five-point comparative scoring system (−2 to +2) was used to assess seven quality criteria and overall diagnostic value. Statistical analysis was subsequently performed of reader ratings (n=16 925). Results For most quality criteria, both CR systems were rated as equivalent to or better than SFM. The CR systems were significantly better at demonstrating skin edge and background tissue (p<1×10−5). Microcalcification was best demonstrated on the CR50 system (p<1×10−5). The overall diagnostic value of both CR systems was rated as being as good as or better than SFM (p<1×10−5). Conclusion In this clinical setting, the overall diagnostic performance of both CR systems was as good as or better than SFM, with the CR50 system performing better than the CR100. PMID:22096218

Production of charcoal briquettes from biomass for community use

NASA Astrophysics Data System (ADS)

Suttibak, S.; Loengbudnark, W.

2018-01-01

This article reports of a study on the production of charcoal briquettes from biomass for community use. Manufacture of charcoal briquettes was done using a briquette machine with a screw compressor. The aim of this research was to investigate the effects of biomass type upon the properties and performance of charcoal briquettes. The biomass samples used in this work were sugarcane bagasse (SB), cassava rhizomes (CR) and water hyacinth (WH) harvested in Udon Thani, Thailand. The char from biomass samples was produced in a 200-liter biomass incinerator. The resulting charcoal briquettes were characterized by measuring their properties and performance including moisture content, volatile matter, fixed carbon and ash contents, elemental composition, heating value, density, compressive strength and extinguishing time. The results showed that the charcoal briquettes from CR had more favorable properties and performance than charcoal briquettes from either SB or WH. The lower heating values (LHV) of the charcoal briquettes from SB, CR and WH were 26.67, 26.84 and 16.76 MJ/kg, respectively. The compressive strengths of charcoal briquettes from SB, CR and WH were 54.74, 80.84 and 40.99 kg/cm2, respectively. The results of this research can contribute to the promotion and development of cost-effective uses of agricultural residues. Additionally, it can assist communities in achieving sustainable self-sufficiency, which is in line with our late King Bhumibol’s economic sufficiency philosophy.

Prediction of the compression ratio for municipal solid waste using decision tree.

PubMed

Heshmati R, Ali Akbar; Mokhtari, Maryam; Shakiba Rad, Saeed

2014-01-01

The compression ratio of municipal solid waste (MSW) is an essential parameter for evaluation of waste settlement and landfill design. However, no appropriate model has been proposed to estimate the waste compression ratio so far. In this study, a decision tree method was utilized to predict the waste compression ratio (C'c). The tree was constructed using Quinlan's M5 algorithm. A reliable database retrieved from the literature was used to develop a practical model that relates C'c to waste composition and properties, including dry density, dry weight water content, and percentage of biodegradable organic waste using the decision tree method. The performance of the developed model was examined in terms of different statistical criteria, including correlation coefficient, root mean squared error, mean absolute error and mean bias error, recommended by researchers. The obtained results demonstrate that the suggested model is able to evaluate the compression ratio of MSW effectively.

Prediction and optimization of CI engine performance fuelled with Calophyllum inophyllum diesel blend using response surface methodology (RSM).

PubMed

Venugopal, Paramaguru; Kasimani, Ramesh; Chinnasamy, Suresh

2018-06-21

The transportation demand in India is increasing tremendously, which arouses the energy consumption by 4.1 to 6.1% increases each year from 2010 to 2050. In addition, the private vehicle ownership keeps on increasing almost 10% per year during the last decade and reaches 213 million tons of oil consumption in 2016. Thus, this makes India the third largest importer of crude oil in the world. Because of this problem, there is a need of promoting the alternative fuels (biodiesel) which are from different feedstocks for the transportation. This alternative fuel has better emission characteristics compared to neat diesel, hence the biodiesel can be used as direct alternative for diesel and it can also be blended with diesel to get better performance. However, the effect of compression ratio, injection timing, injection pressure, composition-blend ratio and air-fuel ratio, and the shape of the cylinder may affect the performance and emission characteristics of the diesel engine. This article deals with the effect of compression ratio in the performance of the engine while using Honne oil diesel blend and also to find out the optimum compression ratio. So the experimentations are conducted using Honne oil diesel blend-fueled CI engine at variable load conditions and at constant speed operations. In order to find out the optimum compression ratio, experiments are carried out on a single-cylinder, four-stroke variable compression ratio diesel engine, and it is found that 18:1 compression ratio gives better performance than the lower compression ratios. Engine performance tests were carried out at different compression ratio values. Using experimental data, regression model was developed and the values were predicted using response surface methodology. Then the predicted values were validated with the experimental results and a maximum error percentage of 6.057 with an average percentage of error as 3.57 were obtained. The optimum numeric factors for different responses were also selected using RSM.

Serum and urine chromium as indices of chromium status in tannery workers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Randall, J.A.; Gibson, R.S.

Serum and urinary Cr levels of a selected group of men exposed to CrIII in four Southern Ontario tanneries were compared with those of men not exposed to Cr. Fasted blood samples were obtained from 72 tannery workers (TW; mean age +/- SD = 36 +/- 12 years) and from 52 controls (CS; mean age +/- SD = 41 +/- 13 years). Serum Cr levels as determined by graphite furnace atomic absorption spectrophotometry were significantly higher (P = 0.0001) for TW (median 0.49 ng/ml, range 0.37-0.81) than for CS (median 0.15 ng/ml, range 0.12-0.20). Urine samples were collected from 49more » TW and 43 CS on a Friday pm and from 42 TW on a Monday am. Urinary creatine (Cre) was determined by the Jaffe reaction. For Friday samples, the median urinary Cr/Cre ratio was significantly higher (P = 0.0001) for TW (median 0.83 ng/mg, range 0.48-1.82) than for CS (median 0.18 ng/mg, range 0.13-0.26). For TW, Cr/Cre was correlated with serum Cr (r = 0.72, P = 0.0001). Neither urinary Cr/Cre nor serum Cr was correlated with length of employment in the tanning industry. There were significant differences in serum Cr levels and urinary Cr/Cre ratios among TW employed in different areas of the tanneries. For TW, the median urinary Cr/Cre ratio for Monday morning samples was significantly lower than for Friday afternoon samples (P = 0.03). These data indicate that CrIII is absorbed and that serum and urine Cr in tannery workers may be indices of Cr exposure and status.« less

Serum and urine chromium as indices of chromium status in tannery workers.

PubMed

Randall, J A; Gibson, R S

1987-05-01

Serum and urinary Cr levels of a selected group of men exposed to CrIII in four Southern Ontario tanneries were compared with those of men not exposed to Cr. Fasted blood samples were obtained from 72 tannery workers (TW; mean age +/- SD = 36 +/- 12 years) and from 52 controls (CS; mean age +/- SD = 41 +/- 13 years). Serum Cr levels as determined by graphite furnace atomic absorption spectrophotometry were significantly higher (P = 0.0001) for TW (median 0.49 ng/ml, range 0.37-0.81) than for CS (median 0.15 ng/ml, range 0.12-0.20). Urine samples were collected from 49 TW and 43 CS on a Friday pm and from 42 TW on a Monday am. Urinary creatine (Cre) was determined by the Jaffe reaction. For Friday samples, the median urinary Cr/Cre ratio was significantly higher (P = 0.0001) for TW (median 0.83 ng/mg, range 0.48-1.82) than for CS (median 0.18 ng/mg, range 0.13-0.26). For TW, Cr/Cre was correlated with serum Cr (r = 0.72, P = 0.0001). Neither urinary Cr/Cre nor serum Cr was correlated with length of employment in the tanning industry. There were significant differences in serum Cr levels and urinary Cr/Cre ratios among TW employed in different areas of the tanneries. For TW, the median urinary Cr/Cre ratio for Monday morning samples was significantly lower than for Friday afternoon samples (P = 0.03). These data indicate that CrIII is absorbed and that serum and urine Cr in tannery workers may be indices of Cr exposure and status.

Behavior of an improved Zr fuel cladding with oxidation resistant coating under loss-of-coolant accident conditions

NASA Astrophysics Data System (ADS)

Park, Dong Jun; Kim, Hyun Gil; Jung, Yang Il; Park, Jung Hwan; Yang, Jae Ho; Koo, Yang Hyun

2016-12-01

This study investigates protective coatings for improving the high temperature oxidation resistance of Zr fuel claddings for light water nuclear reactors. FeCrAl alloy and Cr layers were deposited onto Zr plates and tubes using cold spraying. For the FeCrAl/Zr system, a Mo layer was introduced between the FeCrAl coating and the Zr matrix to prevent inter-diffusion at high temperatures. Both the FeCrAl and Cr coatings improved the oxidation resistance compared to that of the uncoated Zr alloy when exposed to a steam environment at 1200 °C. The ballooning behavior and mechanical properties of the coated cladding samples were studied under simulated loss-of-coolant accident conditions. The coated samples showed higher burst temperatures, lower circumferential strain, and smaller rupture openings compared to the uncoated Zr. Although 4-point bend tests of the coated samples showed a small increase in the maximum load, ring compression tests of a sectioned sample showed increased ductility.

Effect of feeding sorghum straw based complete rations with different roughage to concentrate ratio on dry matter intake, nutrient utilization, and nitrogen balance in Nellore ram lambs.

PubMed

Malisetty, Venkateswarlu; Yerradoddi, Ramana Reddy; Devanaboina, Nagalakshmi; Mallam, Mahender; Mitta, Pavani

2014-06-01

An experiment was conducted by feeding sorghum straw (Sorghum bicolor) based complete rations at roughage concentrate ratio 70:30 (CR-I), 60:40 (CR-II), 50:50 (CR-III), and 40:60 (CR-IV) for 180 days to find out suitable ratio of sorghum straw in the complete ration (mash form) on nutrient utilization and nitrogen balance in Nellore ram lambs. The DMI (g/day) increased significantly (P < 0.05) as level of concentrate increased in complete rations. No significant difference was found in digestibilities of proximate nutrients. However, CP digestibility was higher either significantly or nonsignificantly by 2.12, 5.50, and 9.36 %, respectively, in lambs fed with CR-II (P > 0.05), CR-III (P > 0.05), and CR-IV (P < 0.05) rations in comparison to lambs fed with CR-I ration. Furthermore, CP digestibility was higher by 7.09 and 3.66 % in lambs fed with CR-IV ration than those fed with CR-II (P < 0.05) and CR-III (P > 0.05) ration. The average CWC digestibility coefficients were comparable among four rations. The N intake (g/day) was significantly (P < 0.01) different and progressively increased by 31.46, 48.69, and 82.86 % in ram lambs fed with CR-II, CR-III, and CR-IV rations, respectively, in comparison to CR-I ration. The N balance (g/day) was higher either significantly or nonsignificantly by 34.46 (P > 0.05), 133.46 (P < 0.01), and 198.87 % (P < 0.01) with CR-II, CR-III, and CR-IV rations, respectively, in comparison to CR-I ration. Based on results, it is inferred that the level of sorghum straw in complete ration had no effect on digestibility of nutrients barring crude protein in Nellore ram lambs.

Compression of next-generation sequencing quality scores using memetic algorithm

PubMed Central

2014-01-01

Background The exponential growth of next-generation sequencing (NGS) derived DNA data poses great challenges to data storage and transmission. Although many compression algorithms have been proposed for DNA reads in NGS data, few methods are designed specifically to handle the quality scores. Results In this paper we present a memetic algorithm (MA) based NGS quality score data compressor, namely MMQSC. The algorithm extracts raw quality score sequences from FASTQ formatted files, and designs compression codebook using MA based multimodal optimization. The input data is then compressed in a substitutional manner. Experimental results on five representative NGS data sets show that MMQSC obtains higher compression ratio than the other state-of-the-art methods. Particularly, MMQSC is a lossless reference-free compression algorithm, yet obtains an average compression ratio of 22.82% on the experimental data sets. Conclusions The proposed MMQSC compresses NGS quality score data effectively. It can be utilized to improve the overall compression ratio on FASTQ formatted files. PMID:25474747

Study of multi-kW solar arrays for Earth orbit application

NASA Technical Reports Server (NTRS)

1980-01-01

Planar and concentrator solar array configurations based on silicon and gallium arsenide solar cells were conceptualized and on-orbit maintainability was addressed. Four basic categories emerged: (1) planar (non concentrated) with silicon cells, (2) low-CR (concentration ratio = 3.4) with silicon cells, (3) low-CR with GaAs, and (4) high-CR (concentration ratio = 62.5) with GaAs. A very high-CR (concentration ratio = 200) was investigated but rejected on thermal grounds. Nonrecurring and recurring cost elements for each of the four concepts selected were compared over a 15 year life cycle. Under conditions where the gallium arsenide cells can be produced for less than $25 per 2 x 2 cm, the low CR concentrator emerges as the most cost effective configuration. However, the producibility risk remains higher on the gallium arsenide cell.

Remediation of Cr(VI)-Contaminated Soil Using the Acidified Hydrazine Hydrate.

PubMed

Ma, Yameng; Li, Fangfang; Jiang, Yuling; Yang, Weihua; Lv, Lv; Xue, Haotian; Wang, Yangyang

2016-09-01

Acidified hydrazine hydrate was used to remediate Cr(VI)-contaminated soil. The content of water-soluble Cr(VI) in contaminated soil was 4977.53 mg/kg. The optimal initial pH of hydrazine hydrate solution, soil to solution ratio and molar ratio of Cr(VI) to hydrazine hydrate for remediation of Cr(VI)-contaminated soil were 5.0, 3:1 and 1:3, respectively. Over 99.50 % of water-soluble Cr(VI) in the contaminated soil was reduced at the optimal condition within 30 min. The remediated soil can keep stable within 4 months. Meanwhile the total phosphorus increased from 0.47 to 4.29 g/kg, indicating that using of acidified hydrazine hydrate is an effective method to remediate Cr(VI)-contaminated soil.

An experimental study of the autoignition characteristics of conventional jet fuel/oxidizer mixtures: Jet-A and JP-8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Kamal; Sung, Chih-Jen

2010-04-15

Ignition delay times of Jet-A/oxidizer and JP-8/oxidizer mixtures are measured using a heated rapid compression machine at compressed charge pressures corresponding to 7, 15, and 30 bar, compressed temperatures ranging from 650 to 1100 K, and equivalence ratios varying from 0.42 to 2.26. When using air as the oxidant, two oxidizer-to-fuel mass ratios of 13 and 19 are investigated. To achieve higher compressed temperatures for fuel lean mixtures (equivalence ratio of {proportional_to}0.42), argon dilution is also used and the corresponding oxidizer-to-fuel mass ratio is 84.9. For the conditions studied, experimental results show two-stage ignition characteristics for both Jet-A and JP-8.more » Variations of both the first-stage and overall ignition delays with compressed temperature, compressed pressure, and equivalence ratio are reported and correlated. It is noted that the negative temperature coefficient phenomenon becomes more prominent at relatively lower pressures. Furthermore, the first-stage-ignition delay is found to be less sensitive to changes in equivalence ratio and primarily dependent on temperature. (author)« less

Effect of one-rescuer compression/ventilation ratios on cardiopulmonary resuscitation in infant, pediatric, and adult manikins.

PubMed

Srikantan, Shoba Krishnan; Berg, Robert A; Cox, Tim; Tice, Lisa; Nadkarni, Vinay M

2005-05-01

Optimal chest compression to ventilation ratio (C:V) for one-rescuer cardiopulmonary resuscitation (CPR) is not known, with current American Heart Association recommendations 3:1 for newborns, 5:1 for children, and 15:2 for adults. C:V ratios influence effectiveness of CPR, but memorizing different ratios is educationally cumbersome. We hypothesized that a 10:2 ratio might provide adequate universal application for all age arrest victims. Clinical study. Tertiary care children's hospital. Thirty-five health care providers. Thirty-five health care providers performed 5-min epochs of one-rescuer CPR at C:V ratios of 3:1, 5:1, 10:2, and 15:2 in random order on infant, pediatric, and adult manikins. Compressions were paced at 100/min by metronome. The number of effective compressions and ventilations delivered per minute was recorded by a trained basic life support instructor. Subjective assessments of fatigue (self-report) and exertion (change in rescuer pulse rate compared with baseline) were assessed. Analysis was by repeated measures analysis of variance and paired Student's t-test. Effective infant compressions per minute did not differ by C:V ratio, but ventilations per minute were greater at 3:1 vs. 5:1, 10:2, and 15:2 (p < .05). Effective pediatric compressions per minute were less at 3:1 vs. 5:1, 10:2, and 15:2 (p < .05) and not different between 5:1, 10:2, and 15:2 ratios. Effective pediatric ventilations per minute were greater at 3:1 than all other ratios and both 5:1 and 10:2 were >15:2 (p < .05). Effective adult compressions per minute were progressively greater with 3:1 vs. 5:1 vs. 10:2 vs. 15:2 (p < .05). Self-efficacy was assessed, and rescuers always subjectively rated 10:2 and 15:2 ratios as easier than 5:1 or 3:1 ratios for all manikins. Rescuer pulse change (exertion) was greater after pediatric and adult vs. infant CPR (p < .05), with no significant difference by C:V ratio. C:V ratio and manikin size have a significant influence on the number of effective compressions and ventilations delivered during ideal, metronome-paced, one-rescuer CPR. Low ratios of 3:1, 5:1, and 10:2 favor ventilation, and high ratios of 15:2 favor compression, especially in adult manikins. Rescuers subjectively preferred C:V ratios of 10:2 and 15:2 over 3:1 or 5:1. Infant CPR caused less exertion and subjective fatigue than pediatric or adult CPR technique, without significant difference by C:V ratio. We speculate that a universal 10:2 C:V ratio for one-rescuer layperson CPR is physiologically reasonable but warrants further study with particular attention to educational value and technique retention.

Proton magnetic resonance spectroscopic findings of cerebral fat embolism induced by triolein emulsion in cats.

PubMed

Baik, S K; Kim, Y-W; Kim, H J; Lee, J W; Cho, B M; Kim, D-H; Choi, S H; Lee, S H; Chang, K H

2008-12-01

In experimental studies, embolization of the cerebral hemisphere with triolein emulsion has revealed reversible magnetic resonance imaging (MRI) findings in the subacute stage. To investigate the changes in the major metabolites, by proton magnetic resonance spectroscopy (MRS), in a cerebral fat embolism induced by a triolein emulsion. The internal carotid arteries of 19 cats were injected with a triolein emulsion, and multivoxel MRS was performed 30 min, 1 day, and 7 days later. In the control group, six cats were injected with normal saline. The MR spectra were evaluated for N-acetyl aspartate (NAA), creatine (Cr), and choline (Cho), along with the presence of lipid and lactate. Semiquantitative analyses of NAA/Cr, Cho/Cr, NAA/Cho, and lipid/Cr ratios compared the median values of the ipsilateral metabolite ratios with those of the contralateral side and in the control group for each point in time. The NAA/Cr, Cho/Cr, and NAA/Cho ratios in the ipsilateral cerebral hemisphere of the embolized group after 30 min, 1 day, and 7days were not significantly different from the contralateral hemisphere of the embolized and control groups (P>0.05). The lipid/Cr ratio in the ipsilateral cerebral hemisphere of the embolized group was significantly higher when compared with the control group (P=0.012 at 30 min, P=0.001 on day 1, and P=0.018 on day 7). Cerebral fat embolism induced by a triolein emulsion resulted in no significant change in the major metabolites of the brain in the acute stage, except for an elevated lipid/Cr ratio, which suggests the absence of any significant hypoxic-ischemic changes in the lesions embolized using a fat emulsion.

Design of a Biorthogonal Wavelet Transform Based R-Peak Detection and Data Compression Scheme for Implantable Cardiac Pacemaker Systems.

PubMed

Kumar, Ashish; Kumar, Manjeet; Komaragiri, Rama

2018-04-19

Bradycardia can be modulated using the cardiac pacemaker, an implantable medical device which sets and balances the patient's cardiac health. The device has been widely used to detect and monitor the patient's heart rate. The data collected hence has the highest authenticity assurance and is convenient for further electric stimulation. In the pacemaker, ECG detector is one of the most important element. The device is available in its new digital form, which is more efficient and accurate in performance with the added advantage of economical power consumption platform. In this work, a joint algorithm based on biorthogonal wavelet transform and run-length encoding (RLE) is proposed for QRS complex detection of the ECG signal and compressing the detected ECG data. Biorthogonal wavelet transform of the input ECG signal is first calculated using a modified demand based filter bank architecture which consists of a series combination of three lowpass filters with a highpass filter. Lowpass and highpass filters are realized using a linear phase structure which reduces the hardware cost of the proposed design approximately by 50%. Then, the location of the R-peak is found by comparing the denoised ECG signal with the threshold value. The proposed R-peak detector achieves the highest sensitivity and positive predictivity of 99.75 and 99.98 respectively with the MIT-BIH arrhythmia database. Also, the proposed R-peak detector achieves a comparatively low data error rate (DER) of 0.002. The use of RLE for the compression of detected ECG data achieves a higher compression ratio (CR) of 17.1. To justify the effectiveness of the proposed algorithm, the results have been compared with the existing methods, like Huffman coding/simple predictor, Huffman coding/adaptive, and slope predictor/fixed length packaging.

Thermofluidic compression effects to achieve combustion in a low-compression scramjet engine

NASA Astrophysics Data System (ADS)

Moura, A. F.; Wheatley, V.; Jahn, I.

2018-07-01

The compression provided by a scramjet inlet is an important parameter in its design. It must be low enough to limit thermal and structural loads and stagnation pressure losses, but high enough to provide the conditions favourable for combustion. Inlets are typically designed to achieve sufficient compression without accounting for the fluidic, and subsequently thermal, compression provided by the fuel injection, which can enable robust combustion in a low-compression engine. This is investigated using Reynolds-averaged Navier-Stokes numerical simulations of a simplified scramjet engine designed to have insufficient compression to auto-ignite fuel in the absence of thermofluidic compression. The engine was designed with a wide rectangular combustor and a single centrally located injector, in order to reduce three-dimensional effects of the walls on the fuel plume. By varying the injected mass flow rate of hydrogen fuel (equivalence ratios of 0.22, 0.17, and 0.13), it is demonstrated that higher equivalence ratios lead to earlier ignition and more rapid combustion, even though mean conditions in the combustor change by no more than 5% for pressure and 3% for temperature with higher equivalence ratio. By supplementing the lower equivalence ratio with helium to achieve a higher mass flow rate, it is confirmed that these benefits are primarily due to the local compression provided by the extra injected mass. Investigation of the conditions around the fuel plume indicated two connected mechanisms. The higher mass flow rate for higher equivalence ratios generated a stronger injector bow shock that compresses the free-stream gas, increasing OH radical production and promoting ignition. This was observed both in the higher equivalence ratio case and in the case with helium. This earlier ignition led to increased temperature and pressure downstream and, consequently, stronger combustion. The heat release from combustion provided thermal compression in the combustor, further increasing combustion efficiency.

Thermofluidic compression effects to achieve combustion in a low-compression scramjet engine

NASA Astrophysics Data System (ADS)

Moura, A. F.; Wheatley, V.; Jahn, I.

2017-12-01

The compression provided by a scramjet inlet is an important parameter in its design. It must be low enough to limit thermal and structural loads and stagnation pressure losses, but high enough to provide the conditions favourable for combustion. Inlets are typically designed to achieve sufficient compression without accounting for the fluidic, and subsequently thermal, compression provided by the fuel injection, which can enable robust combustion in a low-compression engine. This is investigated using Reynolds-averaged Navier-Stokes numerical simulations of a simplified scramjet engine designed to have insufficient compression to auto-ignite fuel in the absence of thermofluidic compression. The engine was designed with a wide rectangular combustor and a single centrally located injector, in order to reduce three-dimensional effects of the walls on the fuel plume. By varying the injected mass flow rate of hydrogen fuel (equivalence ratios of 0.22, 0.17, and 0.13), it is demonstrated that higher equivalence ratios lead to earlier ignition and more rapid combustion, even though mean conditions in the combustor change by no more than 5% for pressure and 3% for temperature with higher equivalence ratio. By supplementing the lower equivalence ratio with helium to achieve a higher mass flow rate, it is confirmed that these benefits are primarily due to the local compression provided by the extra injected mass. Investigation of the conditions around the fuel plume indicated two connected mechanisms. The higher mass flow rate for higher equivalence ratios generated a stronger injector bow shock that compresses the free-stream gas, increasing OH radical production and promoting ignition. This was observed both in the higher equivalence ratio case and in the case with helium. This earlier ignition led to increased temperature and pressure downstream and, consequently, stronger combustion. The heat release from combustion provided thermal compression in the combustor, further increasing combustion efficiency.

CrAlN coating to enhance the power loss and magnetostriction in grain oriented electrical steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goel, Vishu; Anderson, Philip; Hall, Jeremy

Grain oriented electrical steels (GOES) are coated with aluminium orthophosphate on top of a forsterite (Mg{sub 2}SiO{sub 4}) layer to provide stress and insulation resistance to reduce the power loss and magnetostriction. In this work Chromium Aluminium Nitride (CrAlN) was coated on GOES samples with electron beam physical vapour deposition and was tested in the single strip and magnetostriction tester to measure the power loss and magnetostriction before and after coating. Power loss was reduced by 2% after coating and 6 % post annealing at 800 °C. For applied compressive stress of 6 MPa, the magnetostrictive strain was zero with themore » CrAlN coating as compared to 22 and 24 μϵ for fully finished GOES and GOES without phosphate coating. The thickness of the coating was found to be 1.9 ± 0.2 μm estimated with Glow Discharge Optical Emission Spectroscopy (GDOES). The magnetic domain imaging showed domain narrowing after coating. The reduction in power loss and magnetostriction was due to the large residual compressive stress and Young’s modulus (270 GPa) of the coating.« less

Pulse compression in an electro-optic Q-switched diode-pumped YVO4/Nd:YVO4 laser with a Cr4+:YAG saturable absorber.

PubMed

Li, Tao; Zhao, Shengzhi; Zhuo, Zhuang; Yang, Kejian; Li, Guiqiu; Li, Dechun

2009-04-20

A diode end-pumped doubly Q-switched YVO4/Nd:YVO4 laser has been realized for the first time to our knowledge by using both an electro-optic (EO) modulator and a Cr4):YAG saturable absorber. A 3.8 ns pulse width is generated by this laser under a pump power of 15 W at 2 kHz, which is obviously compressed in comparison with that of 8.8 ns from a single actively EO Q-switched laser. Under the same conditions, peak power values of 174.7 and 93 kW are also obtained. A coupled equation is given to theoretically analyze the experimental data. The experimental and theoretical results show that the doubly Q-switched laser has the advantages of a shorter pulse width and higher pulse peak power in contrast with a singly Q-switched laser.

Effects of temperature on serrated flows of Al 0.5CoCrCuFeNi high-entropy alloy

DOE PAGES

Chen, Shuying; Xie, Xie; Chen, Bilin; ...

2015-08-14

Compression behavior of the Al 0.5CoCrCuFeNi high-entropy alloy (HEA) was studied at different temperatures from 673 K to 873 K at a low strain rate of 5 x 10 –5/s to investigate the temperature effect on the mechanical properties and serration behavior. The face-centered-cubic (fcc) structure is confirmed at the lower temperature of 673 K and 773 K, and a structure of mixed fcc and body-centered cubic (bcc) is identified at a higher temperature of 873 K after compression tests using high-energy synchrotron x-ray diffraction. As a result, by comparing the stress–strain curves at different temperatures, two opposite directions ofmore » serrations types were found, named upward serrations appearing at 673 K and 773 K and downward serrations at 873 K, which may be due to dynamic strain aging.« less

Compression, bend, and tension studies on forged Al67Ti25Cr8 and Al66Ti25Mn(g) L1(2) compounds

NASA Technical Reports Server (NTRS)

Kumar, K. S.; Brown, S. A.; Whittenberger, J. D.

1991-01-01

Cast, homogenized, and isothermally forged aluminum-rich L1(2) compounds Al67Ti25Cr8 and Al66Ti25Mn(g) were tested in compression as a function of temperature and as a function of strain rate at elevated temperatures (1000 K and 1100 K). Three-point bend specimens were tested as a function of temperature in the range 300 K to 873 K. Strain gages glued on the tensile side of the ambient and 473 K specimens enabled direct strain measurements. A number of 'buttonhead' tensile specimens were electro-discharge machined, fine polished, and tested between ambient and 1073 K for yield strength and ductility as a function of temperature. Scanning electron microscope (SEM) examination of fracture surfaces from both the bend and tensile specimens revealed a gradual transition from transgranular cleavage to intergranular failure with increasing temperature.

Enstatite Meteorites and the Original Heterogeneity of Mn-53 Distribution in the Solar Nebula

NASA Technical Reports Server (NTRS)

Lugmair, Guenter W.

1999-01-01

We have shown earlier that the relative abundance of radiogenic Cr-53 in bulk ordinary chondrites (approximately 0.48 epsilon) is clearly different from that in the earth-moon system (0 epsilon). The SNC parent body (Mars) is characterized by an intermediate Cr-53 excess (approximately 0.23 epsilon). We have also shown that the Mn-Cr systematics of the howardite-eucrite-diogenite parent body (HED PB, the asteroid Vesta) is consistent with the chondritic Mn/Cr ratio in the bulk HED PB and that it has a Cr-53 excess of approximately 0.5 epsilon units which is within error the same as that of chondrites. It appears that the excesses of Cr-53 in these planets are a function of their present heliocentric distance. The study of some other meteorite classes (angrites, pallasites, primitive achondrites) has shown that their Mn-CR systematics is consistent with that of the ordinary chondrites. The observed gradient in the radiogenic Cr-53 abundances can be explained by a). an early volatility controlled radial Mn/Cr fractionation in the nebula or b). an original heterogeneity of Mn-53. The first assumption, however, requires the Mn/Cr ratios of the bulk Earth and Mars to be considerably lower than the inferred model Mn/Cr ratios for these two planets. For this reason, we suggested that the observed gradient is due to an original radial Mn-53 heterogeneity in the late nebula.

Corrosion and Wear Behaviors of Cr-Doped Diamond-Like Carbon Coatings

NASA Astrophysics Data System (ADS)

Viswanathan, S.; Mohan, L.; Bera, Parthasarathi; Kumar, V. Praveen; Barshilia, Harish C.; Anandan, C.

2017-08-01

A combination of plasma-enhanced chemical vapor deposition and magnetron sputtering techniques has been employed to deposit chromium-doped diamond-like carbon (DLC) coatings on stainless steel, silicon and glass substrates. The concentrations of Cr in the coatings are varied by changing the parameters of the bipolar pulsed power supply and the argon/acetylene gas composition. The coatings have been studied for composition, morphology, surface nature, nanohardness, corrosion resistance and wear resistance properties. The changes in I D / I G ratio with Cr concentrations have been obtained from Raman spectroscopy studies. Ratio decreases with an increase in Cr concentration, and it has been found to increase at higher Cr concentration, indicating the disorder in the coating. Carbide is formed in Cr-doped DLC coatings as observed from XPS studies. There is a decrease in sp 3/ sp 2 ratios with an increase in Cr concentration, and it increases again at higher Cr concentration. Nanohardness studies show no clear dependence of hardness on Cr concentration. DLC coatings with lower Cr contents have demonstrated better corrosion resistance with better passive behavior in 3.5% NaCl solution, and corrosion potential is observed to move toward nobler (more positive) values. A low coefficient of friction (0.15) at different loads is observed from reciprocating wear studies. Lower wear volume is found at all loads on the Cr-doped DLC coatings. Wear mechanism changes from abrasive wear on the substrate to adhesive wear on the coating.

Determination of the Cryolite Ratio of KF-NaF-AlF3 Electrolyte by Conductivity Method

NASA Astrophysics Data System (ADS)

Yan, Hengwei; Yang, Jianhong; Liu, Zhanwei; Wang, Chengzhi; Ma, Wenhui

2018-05-01

The cryolite ratio (CR) is an important parameter for the electrolyte in aluminum reduction cells. The measurement method for the CR of the KF-NaF-AlF3 system acid (CR < 3) electrolyte by means of electrical conductivity was initially developed, and the formula for calculating the CR was deduced. This method has the advantages of simple operation and high precision. In addition, the relative standard deviations (RSD) of the measurement are < 1.2 pct, and the analysis error of the NaF or KF content has little effect on the determination of the CR.

Real-time compression of raw computed tomography data: technology, architecture, and benefits

NASA Astrophysics Data System (ADS)

Wegener, Albert; Chandra, Naveen; Ling, Yi; Senzig, Robert; Herfkens, Robert

2009-02-01

Compression of computed tomography (CT) projection samples reduces slip ring and disk drive costs. A lowcomplexity, CT-optimized compression algorithm called Prism CTTM achieves at least 1.59:1 and up to 2.75:1 lossless compression on twenty-six CT projection data sets. We compare the lossless compression performance of Prism CT to alternative lossless coders, including Lempel-Ziv, Golomb-Rice, and Huffman coders using representative CT data sets. Prism CT provides the best mean lossless compression ratio of 1.95:1 on the representative data set. Prism CT compression can be integrated into existing slip rings using a single FPGA. Prism CT decompression operates at 100 Msamp/sec using one core of a dual-core Xeon CPU. We describe a methodology to evaluate the effects of lossy compression on image quality to achieve even higher compression ratios. We conclude that lossless compression of raw CT signals provides significant cost savings and performance improvements for slip rings and disk drive subsystems in all CT machines. Lossy compression should be considered in future CT data acquisition subsystems because it provides even more system benefits above lossless compression while achieving transparent diagnostic image quality. This result is demonstrated on a limited dataset using appropriately selected compression ratios and an experienced radiologist.

The effect of hydraulic bed movement on the quality of chest compressions.

PubMed

Park, Maeng Real; Lee, Dae Sup; In Kim, Yong; Ryu, Ji Ho; Cho, Young Mo; Kim, Hyung Bin; Yeom, Seok Ran; Min, Mun Ki

2017-08-01

The hydraulic height control systems of hospital beds provide convenience and shock absorption. However, movements in a hydraulic bed may reduce the effectiveness of chest compressions. This study investigated the effects of hydraulic bed movement on chest compressions. Twenty-eight participants were recruited for this study. All participants performed chest compressions for 2min on a manikin and three surfaces: the floor (Day 1), a firm plywood bed (Day 2), and a hydraulic bed (Day 3). We considered 28 participants of Day 1 as control and each 28 participants of Day 2 and Day 3 as study subjects. The compression rates, depths, and good compression ratios (>5-cm compressions/all compressions) were compared between the three surfaces. When we compared the three surfaces, we did not detect a significant difference in the speed of chest compressions (p=0.582). However, significantly lower values were observed on the hydraulic bed in terms of compression depth (p=0.001) and the good compression ratio (p=0.003) compared to floor compressions. When we compared the plywood and hydraulic beds, we did not detect significant differences in compression depth (p=0.351) and the good compression ratio (p=0.391). These results indicate that the movements in our hydraulic bed were associated with a non-statistically significant trend towards lower-quality chest compressions. Copyright © 2017 Elsevier Inc. All rights reserved.

A comparison of select image-compression algorithms for an electronic still camera

NASA Technical Reports Server (NTRS)

Nerheim, Rosalee

1989-01-01

This effort is a study of image-compression algorithms for an electronic still camera. An electronic still camera can record and transmit high-quality images without the use of film, because images are stored digitally in computer memory. However, high-resolution images contain an enormous amount of information, and will strain the camera's data-storage system. Image compression will allow more images to be stored in the camera's memory. For the electronic still camera, a compression algorithm that produces a reconstructed image of high fidelity is most important. Efficiency of the algorithm is the second priority. High fidelity and efficiency are more important than a high compression ratio. Several algorithms were chosen for this study and judged on fidelity, efficiency and compression ratio. The transform method appears to be the best choice. At present, the method is compressing images to a ratio of 5.3:1 and producing high-fidelity reconstructed images.

Reduced N-acetylaspartate to creatine ratio in the posterior cingulate correlates with cognition in Alzheimer's disease following four months of rivastigmine treatment.

PubMed

Penner, Jacob; Wells, Jennie L; Borrie, Michael J; Woolmore-Goodwin, Sarah M; Bartha, Robert

2015-01-01

To determine whether 4 months of rivastigmine treatment would result in metabolic changes and whether metabolic changes correlate with changes in cognition in people with Alzheimer's disease (AD). Magnetic resonance spectra were acquired from the posterior cingulate cortex of subjects with AD at 3 T. Magnetic resonance imaging scans and cognitive tests were performed before and 4 months after the beginning of the treatment. Metabolite concentrations were quantified and used to calculate the metabolite ratios. On average, the N-acetylaspartate/creatine (NAA/Cr) ratio decreased by 12.7% following 4 months of rivastigmine treatment, but changes in the NAA/Cr ratio correlated positively with changes in Mini-Mental State Examination scores. This positive correlation between changes in NAA/Cr and changes in cognitive performance suggests that the NAA/Cr ratio could be an objective indicator of a response to rivastigmine treatment. © 2014 S. Karger AG, Basel

Serum and urinary cystatin C in cats with feline immunodeficiency virus infection and cats with hyperthyroidism.

PubMed

Ghys, Liesbeth Fe; Paepe, Dominique; Taffin, Elien Rl; Vandermeulen, Eva; Duchateau, Luc; Smets, Pascale My; Delanghe, Joris; Daminet, Sylvie

2016-08-01

The objective of this study was to investigate serum cystatin C (sCysC) and urinary cystatin C (uCysC) in cats with hyperthyroidism and cats with feline immunodeficiency virus (FIV). Thirty cats with FIV, 26 hyperthyroid cats and 28 healthy cats were included. sCysC and uCysC:creatinine (uCysC/uCr) ratio were measured with a human particle-enhanced nephelometric immunoassay, previously validated for feline CysC measurement. Routine renal variables (serum creatinine [sCr], urine specific gravity, urinary protein:creatinine ratio [UPC]) were also measured in the three groups. Cats with hyperthyroidism had significantly higher sCysC and higher uCysC/uCr ratio, lower sCr and a higher UPC than healthy cats. Cats with FIV infection did not show a significantly higher sCysC concentration but had a significantly higher sCr and UPC than healthy cats. uCysC could be detected in only four of them. This study demonstrated that sCysC is increased in cats with hyperthyroidism, in contrast with sCr, but not in cats with FIV. Many hyperthyroid cats, but only four cats with FIV, had an elevated uCysC/uCr ratio. Further studies may reveal if uCysC might be a valuable marker for tubular dysfunction in cats. © The Author(s) 2015.

Effect of occupational manganese exposure on the central nervous system of welders: 1H magnetic resonance spectroscopy and MRI findings.

PubMed

Kim, Eun A; Cheong, Hae-Kwan; Choi, Dae Seob; Sakong, Joon; Ryoo, Jae Wook; Park, Injeong; Kang, Dong Mug

2007-03-01

This study investigated the relationship between long-term occupational manganese (Mn) exposure on the regional Mn concentration in the brain, neuronal loss, and neurobehavioral effects on welders. 1H MRS of the basal ganglia (BG) was performed on 20 male welders and 10 age- and gender-matched, non-office, control workers in a shipyard to assess the metabolic change, and the N-acetylaspartate (NAA)/creatine (Cr), choline (Cho)/Cr and NAA/Cho ratios, by the level of Mn exposure. We also assessed the signal intensity of T1-weighted image of magnetic resonance imaging (MRI) on globus pallidus (GP) compared to that of the frontal white matter (pallidal index, PI). The welders had significantly higher signal intensity than the controls. PI showed a significant dose-response relationship with cumulative exposure index (CEI) (r=0.54, p=0.002). CEI and PI showed different relationships with NAA/Cr according to smoking status, and the correlation was evident only in non-smokers (r=-0.73 and -0.57, respectively). There were no significant differences between the welders and the controls in NAA/Cr, Cho/Cr, and NAA/Cho ratios obtained from BG. CEI was positively correlated with simple reaction time. PI was positively correlated with mean sway (MSWAY), sway area (SWAYA), and sway intensity (SWAYI), and negatively correlated with maximum frequency (MAXF). After categorizing the subjects into two groups according to NAA/Cr ratio level, the low NAA/Cr ratio group showed significantly lower score on digit span backward and significantly higher score on MSWAY, SWAYA and SWAYI in regression analysis than the high NAA/Cr ratio group. We speculated that the NAA/Cr ratio of MRS in BG seems to reflect the cumulative effect of Mn exposure on the human brain. Due to uneven distribution of smoking among the welders and the controls, in addition to the small number of subjects in our study, our findings are needed further studies with a larger number of subjects.

Transport properties of high-performance all-Heusler Co2CrSi/Cu2CrAl/Co2CrSi giant magnetoresistance device

NASA Astrophysics Data System (ADS)

Bai, Z. Q.; Lu, Y. H.; Shen, L.; Ko, V.; Han, G. C.; Feng, Y. P.

2012-05-01

Transport properties of giant magnetoresistance (MR) junction consisting of trilayer Co2CrSi/Cu2CrAl/Co2CrSi Heusler alloys (L21) are studied using first-principles approach based on density functional theory and the non-equilibrium Green's function method. Highly conductive channels are found in almost the entire k-plane when the magnetizations of the electrodes are parallel, while they are completely blocked in the antiparallel configuration, which leads to a high magnetoresistance ratio (the pessimistic MR ratio is nearly 100%). Furthermore, the calculated I-V curve shows that the device behaves as a good spin valve with a considerable disparity in currents under the parallel and antiparallel magnetic configurations of the electrodes. The Co2CrSi/Cu2CrAl/Co2CrSi junction could be useful for high-performance all-metallic current-perpendicular-to-plane giant magnetoresistance reading head for the next generation high density magnetic storage.

Blood urea nitrogen/creatinine ratio identifies a high-risk but potentially reversible form of renal dysfunction in patients with decompensated heart failure.

PubMed

Brisco, Meredith A; Coca, Steven G; Chen, Jennifer; Owens, Anjali Tiku; McCauley, Brian D; Kimmel, Stephen E; Testani, Jeffrey M

2013-03-01

Identifying reversible renal dysfunction (RD) in the setting of heart failure is challenging. The goal of this study was to evaluate whether elevated admission blood urea nitrogen/creatinine ratio (BUN/Cr) could identify decompensated heart failure patients likely to experience improvement in renal function (IRF) with treatment. Consecutive hospitalizations with a discharge diagnosis of heart failure were reviewed. IRF was defined as ≥20% increase and worsening renal function as ≥20% decrease in estimated glomerular filtration rate. IRF occurred in 31% of the 896 patients meeting eligibility criteria. Higher admission BUN/Cr was associated with in-hospital IRF (odds ratio, 1.5 per 10 increase; 95% confidence interval [CI], 1.3-1.8; P<0.001), an association persisting after adjustment for baseline characteristics (odds ratio, 1.4; 95% CI, 1.1-1.8; P=0.004). However, higher admission BUN/Cr was also associated with post-discharge worsening renal function (odds ratio, 1.4; 95% CI, 1.1-1.8; P=0.011). Notably, in patients with an elevated admission BUN/Cr, the risk of death associated with RD (estimated glomerular filtration rate <45) was substantial (hazard ratio, 2.2; 95% CI, 1.6-3.1; P<0.001). However, in patients with a normal admission BUN/Cr, RD was not associated with increased mortality (hazard ratio, 1.2; 95% CI, 0.67-2.0; P=0.59; p interaction=0.03). An elevated admission BUN/Cr identifies decompensated patients with heart failure likely to experience IRF with treatment, providing proof of concept that reversible RD may be a discernible entity. However, this improvement seems to be largely transient, and RD, in the setting of an elevated BUN/Cr, remains strongly associated with death. Further research is warranted to develop strategies for the optimal detection and treatment of these high-risk patients.

Blood Urea Nitrogen/Creatinine Ratio Identifies a High-Risk but Potentially Reversible Form of Renal Dysfunction in Patients With Decompensated Heart Failure

PubMed Central

Brisco, Meredith A.; Coca, Steven G.; Chen, Jennifer; Owens, Anjali Tiku; McCauley, Brian D.; Kimmel, Stephen E.; Testani, Jeffrey M.

2014-01-01

Background Identifying reversible renal dysfunction (RD) in the setting of heart failure is challenging. The goal of this study was to evaluate whether elevated admission blood urea nitrogen/creatinine ratio (BUN/Cr) could identify decompensated heart failure patients likely to experience improvement in renal function (IRF) with treatment. Methods and Results Consecutive hospitalizations with a discharge diagnosis of heart failure were reviewed. IRF was defined as ≥20% increase and worsening renal function as ≥20% decrease in estimated glomerular filtration rate. IRF occurred in 31% of the 896 patients meeting eligibility criteria. Higher admission BUN/Cr was associated with inhospital IRF (odds ratio, 1.5 per 10 increase; 95% confidence interval [CI], 1.3–1.8; P<0.001), an association persisting after adjustment for baseline characteristics (odds ratio, 1.4; 95% CI, 1.1–1.8; P=0.004). However, higher admission BUN/Cr was also associated with post-discharge worsening renal function (odds ratio, 1.4; 95% CI, 1.1–1.8; P=0.011). Notably, in patients with an elevated admission BUN/Cr, the risk of death associated with RD (estimated glomerular filtration rate <45) was substantial (hazard ratio, 2.2; 95% CI, 1.6–3.1; P<0.001). However, in patients with a normal admission BUN/Cr, RD was not associated with increased mortality (hazard ratio, 1.2; 95% CI, 0.67–2.0; P=0.59; p interaction=0.03). Conclusions An elevated admission BUN/Cr identifies decompensated patients with heart failure likely to experience IRF with treatment, providing proof of concept that reversible RD may be a discernible entity. However, this improvement seems to be largely transient, and RD, in the setting of an elevated BUN/Cr, remains strongly associated with death. Further research is warranted to develop strategies for the optimal detection and treatment of these high-risk patients. PMID:23325460

Detection of human immunodeficiency virus induced inflammation and oxidative stress in lenticular nuclei with magnetic resonance spectroscopy despite antiretroviral therapy.

PubMed

Roc, Anne C; Ances, Beau M; Chawla, Sanjeev; Korczykowski, Marc; Wolf, Ronald L; Kolson, Dennis L; Detre, John A; Poptani, Harish

2007-09-01

Single-voxel magnetic resonance spectroscopy measurements of N-acetyl aspartate, choline, and creatine (Cr) are affected in patients with human immunodeficiency virus (HIV) and neurocognitive impairment. However, these metabolic markers are often normalized in affected central nervous system regions, such as the lenticular nuclei, after initiation of highly active antiretroviral therapy (HAART). To examine whether lactate (Lac), a marker of inflammation and anaerobic glycolysis, and lipid, an indicator of cell membrane turnover resulting from oxidative stress, could serve as surrogate biomarkers within the lenticular nuclei of HIV-positive patients with different degrees of neurocognitive impairment. Three-tesla 2-dimensional-chemical shift imaging magnetic resonance spectroscopy at echo times of 30 milliseconds and 135 milliseconds was performed in voxels overlapping the lenticular nuclei of seronegative controls and a spectrum of HIV-positive patients (neurocognitively normal, mildly impaired, or moderately to severely impaired). University of Pennsylvania, Philadelphia. Ten seronegative controls and 45 HIV-positive patients with different degrees of neurocognitive impairment (15 neurocognitively normal patients, 12 mildly impaired patients, and 18 moderately to severely impaired patients). In vivo 2-dimensional-chemical shift imaging magnetic resonance spectroscopy analysis of N-acetyl aspartate:Cr, choline:Cr, Lac:Cr, and (lipid + Lac):Cr ratios among the various groups. In addition, the effect of the degree of HAART central nervous system penetration (high vs low) on these ratios was studied. No significant lenticular nuclei atrophy was detected with volumes similar across all of the groups. Both N-acetyl aspartate:Cr and choline:Cr ratios were similar across all of the groups at either echo time. In contrast, the Lac:Cr ratio was significantly greater in HIV-positive patients with moderate to severe impairment compared with seronegative controls. The (lipid + Lac):Cr ratio was significantly elevated within each HIV-positive subgroup compared with seronegative controls. Within HIV-positive patients receiving HAART, the degree of central nervous system penetration (high vs low) did not affect metabolic ratios. As seen with 2-dimensional-chemical shift imaging magnetic resonance spectroscopy, HIV induces inflammation and oxidative stress in HIV-positive patients despite HAART. Lipid and Lac are more sensitive inflammatory biomarkers that may be used to differentiate HIV-positive subgroups. However, no significant difference in efficacy, as measured by metabolic ratios, exists for high- vs low-central nervous system-penetrating HAART.

The origin of chromitic chondrules and the volatility of Cr under a range of nebular conditions

NASA Technical Reports Server (NTRS)

Krot, Alexander; Ivanova, Marina A.; Wasson, John T.

1993-01-01

We characterize ten chromatic chondrules, two spinelian chondrules andd one spinel-bearing chondrule and summarize data for 120 chromitic inclusions discovered in an extensive survey of ordinary chondrites. Compositional and petrographic evidence suggests that chromitic chondrules and inclusions are closely related. The Cr/(Cr + Al) ratios in the spinal of these objects range from 0.5 to 0.9 and bulk Al2O3 contents are uniformly high (greater than 10 wt%, except for one with 8 wt%). No other elements having comparable solar abundances are so stongly enriched, and alkali feldspar and merrillite are more common than in normal chondrules. The Cr/Mg ratios in chromitic chondrules are 180-750 times the ratios in the bulk chondrite. With the possible exception of magnetic clumping of chromite in the presolar cloud, mechanical processes cannot account for this enrichment. Examination of nebular equilibrium processes shows that 50%-condensation temperatures of Cr at pH2/pH2O of 1500 are several tens of degrees below those of Mg as Mg2SiO4; the condensation of Cr is primarily as MgCr2O4 dissolved in MgAl2O4 at nebular pressures of 10(exp -4) atm or below. At pH2 = 10(exp -3) atm condesation as Cr in Fe-Ni is favored. Making the nebula much more oxidizing reduces the difference in condensation temperatures but Mg remains more refractory. We conclude that nebular equilibrium processes are not responsible for the enhanced Cr/Mg ratios. We propose that both Cr and Al became enriched in residues formed by incomplete evaporation of presolar lumps. We suggest that spinals remained as solid phases when the bulk of the silicates were incorporated into the evaporating melt; vaporization of Al and Cr were inhibited by the slow kinetics of diffusion. Subsequent melting and crystallization of these residues fractionated Cr from Al. The resulting materials constituted major components in the precursors of chromitic chondrules. Our model implies that chromitic chondrules and inclusions preserve the Cr isotopic record of presolar sources.

Production and construction technology of C100 high strength concrete filled steel tube

NASA Astrophysics Data System (ADS)

Wu, Yanli; Sun, Jinlin; Yin, Suhua; Liu, Yu

2017-10-01

In this paper, the effect of the amount of cement, water cement ratio and sand ratio on compressive strength of C100 concrete was studied. The optimum mix ratio was applied to the concrete filled steel tube for the construction of Shenyang Huangchao Wanxin mansion. The results show that the increase of amount of cement, water cement ratio can improve the compressive strength of C100 concrete but increased first and then decreased with the increase of sand ratio. The compressive strength of C100 concrete can reach 110MPa with the amount of cement 600kg/m3, sand ratio 40% and water cement ratio 0.25.

Regional metabolic changes in the hippocampus and posterior cingulate area detected with 3-Tesla magnetic resonance spectroscopy in patients with mild cognitive impairment and Alzheimer disease.

PubMed

Wang, Zhiqun; Zhao, Cheng; Yu, Lei; Zhou, Weidong; Li, Kuncheng

2009-04-01

Magnetic resonance spectroscopy (MRS) plays an important role in early diagnosis of Alzheimer disease (AD). There are many reports on MRS studies among individuals with AD and mild cognitive impairment (MCI). However, very few studies have compared spectroscopic data of different limbic regions among AD and MCI subjects. To compare metabolite changes of different regions in the brain of AD and MCI patients by using 3.0 T short-echo-time MRS. Metabolite ratios in the hippocampus and posterior cingulate area were compared in a group of patients with AD (n=16), MCI (n=16), and normal subjects as a control group (n=16). Clinical neuropsychological tests were measured in all subjects. In the hippocampus, there were significant differences in N-acetylaspartate (NAA)/creatine (Cr), myo-inositol (mI)/Cr, and mI/NAA ratios among the three groups. However, there were no significant differences in choline (Cho)/Cr ratio among the three groups. In the posterior cingulate area, there were no significant differences in the NAA/Cr, Cho/Cr, and mI/Cr ratios among the three groups. However, there were significant differences in mI/NAA ratio between patients with AD and the control group, and between the AD and MCI groups. In addition, there was significant correlation between mI/NAA ratio and Mini Mental Status Exam (MMSE) score in subjects with AD and MCI. The study reveals that the elevation of mI/NAA ratio in the hippocampus is more significant than that in the posterior cingulate area, which corresponds to the pathologic procession of AD. The ratios of mI/NAA in the hippocampus and in the posterior cingulate area together provide valuable discrimination among the three groups (AD, MCI, and controls). There is a significant correlation between mI/NAA ratio and cognitive decline.

Golgi-Colonnier method: correlation of the degree of chromium reduction and pH change with quality of staining.

PubMed

Angulo, A; Merchán, J A; Molina, M

1994-03-01

We examined the role of chromium reduction in the Golgi-Colonnier method, correlating the quality of neuronal impregnation with the levels of hexavalent (CrVI) and trivalent (CrIII) chromium in the tissue and in the chromation fluid (CF). The concentrations of both chromium species were assessed by measuring spectrophotometrically the CrVI before and after oxidizing the sample and by calculating the ratio of CrVI to total chromium (chromium ratio, CrR). The CrR was almost identical in the tissue and the CF, decreasing exponentially during chromation due to a progressive consumption of CrVI to form CrIII. Satisfactory cell impregnation was obtained only when the CrR was 0.45-0.7, regardless of other factors. The CrR values could be accurately predicted by the pH increase of the CF; this increase has proven to be a most reliable criterion to decide the endpoint of the chromation process. The dependence of cell staining on the [CrIII], together with the well-known ability of this species to bridge proteins, suggests that the key event for cell impregnation is the cross-linking of neuronal proteins by CrIII polymers.

Effect of Microstructure on Creep in Directionally Solidified NiAl-31Cr-3Mo

NASA Technical Reports Server (NTRS)

Whittenberger, J. Daniel; Raj, S. V.; Locci, I. E.

2001-01-01

The 1200 to 1400 K slow strain rate characteristics of the directionally solidified (DS) eutectic Ni-33Al-31Cr-3 Mo have been determined as a function of growth rate. While differences in the light optical level microstructure were observed in alloys grown at rates ranging from 7.6 to 508 mm/h, compression testing indicated that all had essentially the same strength. The exception was Ni-33 Al-31Cr-3Mo DS at 25.4 mm/h which was slightly stronger than the other growth velocities; no microstructural reason could be found for this improvement. Comparison of the approximately 1300 K properties revealed that four different DS NiAl-34(Cr,Mo) alloys have a similar creep resistance which suggests that there is a common, but yet unknown, strengthening mechanism.

Effect of Microstructure on Creep in Directionally Solidified NiAl-31Cr-3Mo

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.; Raj, S. V.; Locci, I. E.

2001-01-01

The 1200 to 1400 K slow strain rate characteristics of the directionally solidified (DS) eutectic Ni-33Al-31Cr-3 Mo have been determined as a function of growth rate. While differences in the light optical level microstructure were observed in alloys grown at rates ranging from 7.6 to 508 mm/h, compression testing indicated that all had essentially the same strength. The exception was Ni-33Al-31Cr-3Mo DS at 25.4 mm/h which was slightly stronger than the other growth velocities; no microstructural reason could be found for this improvement. Comparison of the approx. 1300 K properties revealed that four different DS NiAl-34(Cr,Mo) alloys have a similar creep resistance which suggests that there is a common, but yet unknown, strengthening mechanism.

Reduced N-acetylaspartate levels in the frontal cortex of 3,4-methylenedioxymethamphetamine (Ecstasy) users: preliminary results.

PubMed

Reneman, Liesbeth; Majoie, Charles B L M; Flick, Herman; den Heeten, Gerard J

2002-02-01

The perceived safety of the recreational drug methylenedioxymethamphetamine (MDMA), or Ecstasy, conflicts with animal evidence indicating that MDMA damages cortical serotonin (5-HT) neurons at doses similar to those used by humans. Few data are available about the effects of MDMA on the human brain. This study was designed to evaluate MDMA-related alterations in metabolite ratios with single-voxel proton ((1)H) MR spectroscopy. Fifteen male MDMA users (mean lifetime exposure, 723 tablets; mean time since last tablet, 12.0 weeks) and 12 age-matched control subjects underwent single-voxel (1)H MR spectroscopy. N-Acetylaspartate (NAA)/creatine (Cr), NAA/Choline (Cho), and myoinositol (MI)/Cr ratios were measured in midfrontal gray matter, midoccipital gray matter, and right parietal white matter. Data were analyzed with linear model-based multivariate analysis of variance. NAA/Cr (P =.04) and NAA/Cho (P =.03) ratios, markers associated with neuronal loss or dysfunction, were reduced in the frontal cortex of MDMA users. Neither NAA/Cr (P =.72) nor NAA/Cho (P =.12) ratios were different between both groups in occipital gray matter and parietal white matter (P =.18). Extent of previous MDMA use and frontal cortical NAA/Cr (rho = -.50, P =.012) or NAA/Cho (rho = -.550, P <.01) ratios were significantly associated. Reduced NAA/Cr and NAA/Cho ratios at (1)H MR spectroscopy provide evidence for neuronal abnormality in the frontal cortex of MDMA users; these are correlated with the degree of MDMA exposure. These data suggest that MDMA may be a neurotoxin in humans, as it is in animals.

Thermal immobilization of Cr, Cu and Zn of galvanizing wastes in the presence of clay and fly ash.

PubMed

Singh, I B; Chaturvedi, K; Yegneswaran, A H

2007-07-01

In the present investigation thermal treatment of galvanizing waste with clay and fly ash has been carried out to immobilize Cr, Zn, Cu and other metals of the waste at temperature range 850 degrees C to 950 degrees C. Leaching of the metals from the waste and solidified product was analyzed using toxic characteristic leaching procedure (TCLP). Results indicated that the composition of waste and clay treatment temperature are the key factors in determining the stability of solidified product. After heating at 950 degrees C, the solidified specimens of 10% waste with clay have shown comparatively a high compressive strength and less water absorption. However, a decrease in compressive strength and increase in water absorption were noticed after addition of 15% of waste with clay. The leachability of all the metals present in the waste was found to reduce considerably with the increase of treatment temperature. In the case of Cr and Zn, their leachabilty was found at unacceptable levels from the treated product obtained after heating at 850 degrees C However, their leachability was reduced significantly within an acceptable level after treatment at 950 degrees C. The thermal treatment has shown an increase of re-oxidation trend of Cr (III) to Cr (VI) up to 900 degrees C of heating and this trend became almost zero after heating at 950 degrees C. Addition of fly ash did not show any improvement in strength, durability and leachability of metals from the thermally treated product. X-ray diffraction (XRD) analysis of the product confirmed the presence of mixed phases of oxides of toxic metals.

High Temperature Mechanical Properties of Free-Standing HVOF CoNiCrAlY Coatings by Lateral Compression of Circular Tube

NASA Astrophysics Data System (ADS)

Waki, Hiroyuki; Nakamura, Kyousuke; Yamaguchi, Itsuki; Kobayashi, Akira

MCrAlY, M means Co and/or Ni, sprayed coating is used to protect a super alloy substrate from corrosion or oxidation in a gas turbine blade. However, the mechanical properties are not well-known, because there are few proper measurement methods for a thin coating at high temperature. Authors have developed the new easy method to measure the mechanical properties using the lateral compression of a circular tube. The method is useful to apply to a thin coating because it does not need chucking and manufacturing a test piece is very easy. The method is also easily applicable to high temperature measurement. In this study, high temperature mechanical properties, Young's modulus, bending strength and fracture strain, of CoNiCrAlY coatings by HVOF were systematically measured. The results obtained were as follows: Young's modulus and bending strength suddenly decreased beyond 400˜450°C. The Young's modulus and bending strength thermally treated at higher than 1050°C was significantly higher than that of virgin CoNiCrAlY coating. It was found that higher thermal treatment in atmosphere was the most effective in increasing the Young's modulus and bending strength. It was also found that the improvement of Young's modulus was primarily caused by not the effect of TGO but the sintering and diffusion of unfused particles. On the contrary, the fracture strain increased beyond 400°C differently from the bending strength. The fracture strains of CoNiCrAlY thermally treated in vacuum were higher than those of CoNiCrAlY treated in atmosphere. It was found that higher thermal treatment in vacuum was the most effective in increasing the fracture strain.

New Recording Layer of Recordable Digital Versatile Disc with CrOx Film Using Red Laser

NASA Astrophysics Data System (ADS)

Liu, Chung Ping; Hung, Yao Ti

2006-03-01

In this study, CrOx film deposited by rf magnetron reactive sputtering was used as a new recording layer for a recordable digital versatile disc (DVD-R) with a red laser. X-ray photoelectron spectroscopy (XPS) indicated the films have three major components: CrO2, CrO3, and Cr2O3. From disc dynamic tests and atomic force microscope (AFM) images of a polycarbonate (PC) substrate, a DVD-R structure of PC/ZnS-SiO2 (30 nm)/CrOx (120 nm)/ZnS-SiO2 (40 nm)/Ag (50 nm), deposited by sputtering at an O2/Ar flow rate ratio of 0.4, had an improved carrier-to-noise ratio (CNR). The principle of recording depends primarily on the explosive pressure of the O2 released due to laser heating of the annealed CrOx film.

Image quality (IQ) guided multispectral image compression

NASA Astrophysics Data System (ADS)

Zheng, Yufeng; Chen, Genshe; Wang, Zhonghai; Blasch, Erik

2016-05-01

Image compression is necessary for data transportation, which saves both transferring time and storage space. In this paper, we focus on our discussion on lossy compression. There are many standard image formats and corresponding compression algorithms, for examples, JPEG (DCT -- discrete cosine transform), JPEG 2000 (DWT -- discrete wavelet transform), BPG (better portable graphics) and TIFF (LZW -- Lempel-Ziv-Welch). The image quality (IQ) of decompressed image will be measured by numerical metrics such as root mean square error (RMSE), peak signal-to-noise ratio (PSNR), and structural Similarity (SSIM) Index. Given an image and a specified IQ, we will investigate how to select a compression method and its parameters to achieve an expected compression. Our scenario consists of 3 steps. The first step is to compress a set of interested images by varying parameters and compute their IQs for each compression method. The second step is to create several regression models per compression method after analyzing the IQ-measurement versus compression-parameter from a number of compressed images. The third step is to compress the given image with the specified IQ using the selected compression method (JPEG, JPEG2000, BPG, or TIFF) according to the regressed models. The IQ may be specified by a compression ratio (e.g., 100), then we will select the compression method of the highest IQ (SSIM, or PSNR). Or the IQ may be specified by a IQ metric (e.g., SSIM = 0.8, or PSNR = 50), then we will select the compression method of the highest compression ratio. Our experiments tested on thermal (long-wave infrared) images (in gray scales) showed very promising results.

A tabulation of pipe length to diameter ratios as a function of Mach number and pressure ratios for compressible flow

NASA Technical Reports Server (NTRS)

Dixon, G. V.; Barringer, S. R.; Gray, C. E.; Leatherman, A. D.

1975-01-01

Computer programs and resulting tabulations are presented of pipeline length-to-diameter ratios as a function of Mach number and pressure ratios for compressible flow. The tabulations are applicable to air, nitrogen, oxygen, and hydrogen for compressible isothermal flow with friction and compressible adiabatic flow with friction. Also included are equations for the determination of weight flow. The tabulations presented cover a wider range of Mach numbers for choked, adiabatic flow than available from commonly used engineering literature. Additional information presented, but which is not available from this literature, is unchoked, adiabatic flow over a wide range of Mach numbers, and choked and unchoked, isothermal flow for a wide range of Mach numbers.

Correlations between working memory impairment and neurometabolites of prefrontal cortex and lenticular nucleus in patients with major depressive disorder.

PubMed

Shan, Yanyan; Jia, Yanbin; Zhong, Shuming; Li, Xueguo; Zhao, Hui; Chen, Junhao; Lu, Qianyi; Zhang, Lu; Li, Zhinan; Lai, Shunkai; Wang, Ying

2018-02-01

The mechanism of working memory (WM) impairment in MDD remains unclear. We aimed to find out the mechanism by using neuropsychological tests and proton magnetic resonance spectroscopy (1H-MRS). 31 MDD patients and 31 healthy controls were recruited in our study. The WM performance and neurometabolite ratios of prefrontal cortex (PFC) and lenticular nucleus (LN) between two groups were evaluated and compared. And the correlations between abnormal neurometabolite ratios and WM dysfunction were computed. Scores of SDMT, DST(forwards), VRS and 2-back Task(accuracy rate) in MDD were lower than HCs. NAA/Cr ratios of bilateral PFC in MDD were significantly lower than HCs, while no significant differences showed in NAA/Cr ratios of LN and Cho/Cr, mI/Cr values of the bilateral PFC and LN between two groups. And for MDD patients, NAA/Cr ratios in the right PFC were positively correlated with scores of DST (Forwards). Our findings suggest that depressed patients may have impairments in working memory, including phonological loop, visual-spatial sketchpad, episodic buffer and central executive. And the impairment of verbal WM and WM capacity may be associated with the abnormal neurometabolites in the right PFC. Copyright © 2017 Elsevier B.V. All rights reserved.

Cr isotope fractionation factors for Cr(VI) reduction by a metabolically diverse group of bacteria

NASA Astrophysics Data System (ADS)

Basu, Anirban; Johnson, Thomas M.; Sanford, Robert A.

2014-10-01

Reduction of Cr(VI) is an important process that determines the geochemical behavior, mobility and bioavailability of Cr in both terrestrial and marine environments. Many metabolically diverse microorganisms possess Cr(VI) reduction capacity. Cr(VI) reduction fractionates Cr isotopes and thus 53Cr/52Cr ratios can be used to monitor Cr(VI) reduction and redox conditions. The magnitude of isotopic fractionation (ε) for a variety of microbial reduction mechanisms must be known for accurate interpretation of observed shifts in 53Cr/52Cr ratios. We determined isotopic fractionation factors for Cr(VI) reduction by metal reducers Geobacter sulfurreducens and Shewanella sp. strain NR, a denitrifying soil bacterium Pseudomonas stutzeri DCP-Ps1, and a sulfate reducer Desulfovibrio vulgaris. All bacteria investigated in this study produced significant Cr isotope fractionation. The fractionation (ε) for G. sulfurreducens, Shewanella sp. (NR), P. stutzeri DCP-Ps1, and D. vulgaris were -3.03‰ ± 0.12‰, -2.17‰ ± 0.22‰, -3.14‰ ± 0.13‰, and -3.01‰ ± 0.11‰, respectively. Despite differences in microbial strains in this study, the ε did not vary significantly except for Shewanella sp. (NR). Our results suggest that strong isotopic fractionation is induced during Cr(VI) reduction under electron donor poor (∼300 μM) conditions.

Temperature Dependent Electrical Transport Properties of Ni-Cr and Co-Cr Binary Alloys

NASA Astrophysics Data System (ADS)

Thakore, B. Y.; Suthar, P. H.; Khambholja, S. G.; Gajjar, P. N.; Bhatt, N. K.; Jani, A. R.

2011-12-01

The temperature dependent electrical transport properties viz. electrical resistivity and thermal conductivity of Ni10Cr90 and Co20Cr80 alloys are computed at various temperatures. The electrical resistivity has been calculated according to Faber-Ziman model combined with Ashcroft-Langreth partial structure factors. In the present work, to include the ion-electron interaction, we have used a well tested local model potential. For exchange-correlation effects, five different forms of local field correction functions due to Hartree (H), Taylor (T), Ichimaru and Utsumi (IU), Farid et al (F) and Sarkar et al (S) are used. The present results due to S function are in good agreement with the experimental data as compared to results obtained using other four functions. The S functions satisfy compressibility sum rule in long wave length limit more accurately as compared to T, IU and F functions, which may be responsible for better agreement of results, obtained using S function. Also, present result confirms the validity of present approach in determining the transport properties of alloys like Ni-Cr and Co-Cr.

Cosmic rays and the magnetic field in the nearby starburst galaxy NGC 253

NASA Astrophysics Data System (ADS)

Heesen, Volker

2008-02-01

The transport of cosmic rays (CR's) in large-scale magnetic fields can be bes t investigated in edge-on galaxies with radio continuum observations including p olarization. I observed the nearby starburst galaxy NGC 253 which hosts one of t he brightest known radio halos with the Effelsberg 100-m telescope and the VLA i nterferometer. The vertical emission profiles follow closely a two-component exp onential distribution where the scaleheight is a linear function of the synchrot ron lifetime of the CR electrons. This requires a convection dominated CR transp ort from the disk into the halo while the CR's lose their energy due to synchrot ron radiation the so-called CR aging. The interaction of the "disk-wind" with th e magnetic field explains the "X"-shaped magnetic field structure centered on th e nucleus where the ordered magnetic field is amplified by compression in the bo undaries of the expanding superbubbles of hot gas.

Elevated temperature deformation of thoria dispersed nickel-chromium

NASA Technical Reports Server (NTRS)

Kane, R. D.; Ebert, L. J.

1974-01-01

The deformation behavior of thoria nickel-chromium (TD-NiCr) was examined over the temperature range 593 C (1100 F) to 1260 C (2300 F) in tension and compression and at 1093 C (2000 F) in creep. Major emphasis was placed on: (1) the effects of the material and test related variables (grain size, temperature, stress and strain rate) on the deformation process; and (2) the evaluation of single crystal TD-NiCr material produced by a directional recrystallization process. Elevated temperature yield strength levels and creep activation enthalpies were found to increase with increasing grain size reaching maximum values for the single crystal TD-NiCr. Stress exponent of the steady state creep rate was also significantly higher for the single crystal TD-NiCr as compared to that determined for the polycrystalline materials. The elevated temperature deformation of TD-NiCr was analyzed in terms of two concurrent, parallel processes: diffusion controlled grain boundary sliding, and dislocation motion.

Cerebral diffusion tensor imaging and in vivo proton magnetic resonance spectroscopy in patients with fulminant hepatic failure.

PubMed

Saksena, Sona; Rai, Vijan; Saraswat, Vivek Anand; Rathore, Ramkishore Singh; Purwar, Ankur; Kumar, Manoj; Thomas, M Albert; Gupta, Rakesh Kumar

2008-07-01

Cerebral edema is a major complication in patients with fulminant hepatic failure (FHF). The aim of this study was to evaluate the metabolite alterations and cerebral edema in patients with FHF using in vivo proton magnetic resonance spectroscopy (MRS) and diffusion tensor imaging, and to look for its reversibility in survivors. Ten FHF patients along with 10 controls were studied. Five of the 10 patients who recovered had a repeat imaging after three weeks. N-acetylaspartate, choline (Cho), glutamine (Gln), glutamine/glutamate (Glx), and myoinositol ratios were calculated with respect to creatine (Cr). Mean diffusivity (MD) and fractional anisotropy (FA) were calculated in different brain regions. Patients exhibited significantly increased Gln/Cr and Glx/Cr, and reduced Cho/Cr ratios, compared to controls. In the follow-up study, all metabolite ratios were normalized except Glx/Cr. Significantly decreased Cho/Cr were observed in deceased patients compared to controls. In patients, significantly decreased MD and FA values were observed in most topographical locations of the brain compared to controls. MD and FA values showed insignificant increase in the follow-up study compared to their first study. We conclude that the Cho/Cr ratio appears to be an in vivo marker of prognosis in FHF. Decreased MD values suggest predominant cytotoxic edema may be present. Persistence of imaging and MRS abnormalities at three weeks' clinical recovery suggests that metabolic recovery may take longer than clinical recovery in FHF patients.

Compressing DNA sequence databases with coil.

PubMed

White, W Timothy J; Hendy, Michael D

2008-05-20

Publicly available DNA sequence databases such as GenBank are large, and are growing at an exponential rate. The sheer volume of data being dealt with presents serious storage and data communications problems. Currently, sequence data is usually kept in large "flat files," which are then compressed using standard Lempel-Ziv (gzip) compression - an approach which rarely achieves good compression ratios. While much research has been done on compressing individual DNA sequences, surprisingly little has focused on the compression of entire databases of such sequences. In this study we introduce the sequence database compression software coil. We have designed and implemented a portable software package, coil, for compressing and decompressing DNA sequence databases based on the idea of edit-tree coding. coil is geared towards achieving high compression ratios at the expense of execution time and memory usage during compression - the compression time represents a "one-off investment" whose cost is quickly amortised if the resulting compressed file is transmitted many times. Decompression requires little memory and is extremely fast. We demonstrate a 5% improvement in compression ratio over state-of-the-art general-purpose compression tools for a large GenBank database file containing Expressed Sequence Tag (EST) data. Finally, coil can efficiently encode incremental additions to a sequence database. coil presents a compelling alternative to conventional compression of flat files for the storage and distribution of DNA sequence databases having a narrow distribution of sequence lengths, such as EST data. Increasing compression levels for databases having a wide distribution of sequence lengths is a direction for future work.

Compressing DNA sequence databases with coil

PubMed Central

White, W Timothy J; Hendy, Michael D

2008-01-01

Background Publicly available DNA sequence databases such as GenBank are large, and are growing at an exponential rate. The sheer volume of data being dealt with presents serious storage and data communications problems. Currently, sequence data is usually kept in large "flat files," which are then compressed using standard Lempel-Ziv (gzip) compression – an approach which rarely achieves good compression ratios. While much research has been done on compressing individual DNA sequences, surprisingly little has focused on the compression of entire databases of such sequences. In this study we introduce the sequence database compression software coil. Results We have designed and implemented a portable software package, coil, for compressing and decompressing DNA sequence databases based on the idea of edit-tree coding. coil is geared towards achieving high compression ratios at the expense of execution time and memory usage during compression – the compression time represents a "one-off investment" whose cost is quickly amortised if the resulting compressed file is transmitted many times. Decompression requires little memory and is extremely fast. We demonstrate a 5% improvement in compression ratio over state-of-the-art general-purpose compression tools for a large GenBank database file containing Expressed Sequence Tag (EST) data. Finally, coil can efficiently encode incremental additions to a sequence database. Conclusion coil presents a compelling alternative to conventional compression of flat files for the storage and distribution of DNA sequence databases having a narrow distribution of sequence lengths, such as EST data. Increasing compression levels for databases having a wide distribution of sequence lengths is a direction for future work. PMID:18489794

Adiabatic pulse propagation in a dispersion-increasing fiber for spectral compression exceeding the fiber dispersion ratio limitation.

PubMed

Chao, Wan-Tien; Lin, Yuan-Yao; Peng, Jin-Long; Huang, Chen-Bin

2014-02-15

Adiabatic soliton spectral compression in a dispersion-increasing fiber (DIF) with a linear dispersion ramp is studied both numerically and experimentally. The anticipated maximum spectral compression ratio (SCR) would be limited by the ratio of the DIF output to the input dispersion values. However, our numerical analyses indicate that SCR greater than the DIF dispersion ratio is feasible, provided the input pulse duration is shorter than a threshold value along with adequate pulse energy control. Experimentally, a SCR of 28.6 is achieved in a 1 km DIF with a dispersion ratio of 22.5.

The NORDA MC&G Map Data Formatting Facility: Development of a Digital Map Data Base

DTIC Science & Technology

1989-12-01

Lempel - Ziv compression . extract such features as roads, water, urban areas, and Also investigated were various transform encoding text from the scanned... Compression Ratios scanned maps revealed a small number of color classes and lar .e homogeneous regions. The original 24-bit Lempel Ziv Lempel Ziv pixel...Various high performance, lossless compression tech- Table 6. Compression ratios for VQ classification niques were tried. followed by Lempel Ziv

Structure and Mechanical Properties of CrTiAlN/TiAlN Composite Coatings Deposited by Multi-Arc Ion Plating

NASA Astrophysics Data System (ADS)

Yan, Shaojian; Tian, Canxin; Huang, Zhihong; Yang, Bing; Fu, Dejun

2014-10-01

CrTiAlN/TiAlN composite coatings were deposited on cemented carbide by using a home-made industrial scale multi-arc ion plating system. The samples were studied by X-ray diffraction, scanning electron microscopy (SEM), microhardness and ball-on-disk testing. The properties of the CrTiAlN/TiAlN coatings were significantly influenced by the microstructure and the deposition time ratio of TiAlN over CrTiAlN layers. With the increase of deposition time ratio, the microhardness of CrTiAlN/TiAlN increased from 28.6 GPa to 37.5 GPa, much higher than that of CrTiAlN coatings. The friction coefficients of the CrTiAlN/TiAlN coatings were higher than those of CrTiAlN coatings against a cemented carbide ball. The microhardness of the CrTiAlN/TiAlN coatings was changed after annealing at 800°C, and the friction coefficients of the annealed coatings were increased against the cemented carbide ball.

Particular mechanism for continuously varying the compression ratio for an internal combustion engine

NASA Astrophysics Data System (ADS)

Raţiu, S.; Cătălinoiu, R.; Alexa, V.; Miklos, I.; Cioată, V.

2018-01-01

Variable compression ratio (VCR) is a technology to adjust the compression ratio of an internal combustion engine while the engine is in operation. The paper proposes the presentation of a particular mechanism allowing the position of the top dead centre to be changed, while the position of the bottom dead centre remains fixed. The kinematics of the mechanism is studied and its trajectories are graphically represented for different positions of operation.

The Performance of Wavelets for Data Compression in Selected Military Applications

DTIC Science & Technology

1990-02-23

reported. 14. SUBJECT TERMS IS. NUMBER OF PAGES 56 16. PRICE CODE 17. SICURITY CLASSIFICATION I lL SECURITY CLASSIFICATION 19. SECURITY CLASSIF4CATION 20...compression ratio is conservative in the sense that it understates the theoretical compression ratio by taking into account the actual memory...effect of reducing the compresion ratios quoted in the table by the factor 7.8/8.0 = 0.975. AWARE, Inc. 14 registration was then calculated for each

Monitoring interferon β treatment response with magnetic resonance spectroscopy in relapsing remitting multiple sclerosis.

PubMed

Yetkin, Mehmet Fatih; Mirza, Meral; Dönmez, Halil

2016-09-01

The aim of this study is to compare the white matter of multiple sclerosis (MS) patients with healthy controls and to monitor the response to the treatment with magnetic resonance spectroscopy (MRS).Fifteen healthy controls and 36 recently diagnosed MS patients never treated with interferon β were included in this study. In the patient group, MRS was performed before treatment, at 6th and 12th month after the initiation of treatment and once in control group. Patient group was divided into 3 interferon groups randomly. Physical examination findings were recorded as Expanded Disability Status Scale scores before treatment, at 6th and 12th month of interferon treatment.At the end of 1 year follow up, 26 of 36 patients completed the study. In patients' white matter lesions, N-acetylaspartate/creatine (NAA/Cr) ratios were lower than control group's white matters. NAA/Cr ratios were higher in control group's white matter than patient's normal appearing white matter but this difference was not statistically significant. There was no difference in choline/creatine (Cho/Cr) ratios between 2 groups. In follow-up period, NAA/Cr and Cho/Cr ratios obtained from patients' white matter lesions and normal appearing white matter did not change statistically.This study showed that in MS patients' white matters, especially in white matter lesions, neuron viability is reduced compared with healthy controls' normal white matter; and in the patients treated with interferon β NAA/Cr ratios remained stable. These stable levels of metabolite ratios in the patients who received interferon β therapy can be explained with either the shortness of the follow-up period post-treatment or may reflect a positive effect of the beta interferon therapy on the progress of MS.

{sup 53}Mn-{sup 53}Cr CHRONOMETRY OF CB CHONDRITE: EVIDENCE FOR UNIFORM DISTRIBUTION OF {sup 53}Mn IN THE EARLY SOLAR SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamashita, Katsuyuki; Yamakawa, Akane; Nakamura, Eizo

High-precision Cr isotope ratios for chondrules and metal grain separated from CB chondrite Gujba were determined. The {epsilon}{sup 54}Cr values ({epsilon}{sup i}Cr = [({sup i}Cr/{sup 52}Cr){sub sample}/({sup i}Cr/{sup 52}Cr){sub standard} - 1] x 10{sup 4}) for all samples were identical within the analytical uncertainty, with a mean value of +1.29 {+-} 0.02. Uniform {epsilon}{sup 54}Cr signatures of both chondrules and metal grains imply that the Cr isotope systematics of the meteorite was once completely equilibrated. The {epsilon}{sup 53}Cr values of the chondrules and metal grain, on the other hand, display a strong correlation with the {sup 55}Mn/{sup 52}Cr ratio. Themore » {sup 53}Mn/{sup 55}Mn calculated from the slope of the isochron is (3.18 {+-} 0.52) x 10{sup -6}. This corresponds to absolute ages of 4563.7 {+-} 1.2 Ma and 4563.5 {+-} 1.1 Ma using angrites D'Orbigny and LEW 86010, respectively, as time anchors. These ages are consistent with the ages obtained using other short- and long-lived radio nuclides, supporting the uniform distribution of {sup 53}Mn in the early solar nebula.« less

Brain metabolites in autonomic regulatory insular sites in heart failure.

PubMed

Woo, Mary A; Yadav, Santosh K; Macey, Paul M; Fonarow, Gregg C; Harper, Ronald M; Kumar, Rajesh

2014-11-15

Autonomic, pain, and neuropsychologic comorbidities appear in heart failure (HF), likely resulting from brain changes, indicated as loss of structural integrity and functional deficits. Among affected brain sites, the anterior insulae are prominent in serving major regulatory roles in many of the disrupted functions commonly seen in HF. Metabolite levels, including N-acetylaspartate (NAA), creatine (Cr), choline (Cho), and myo-inositol (MI), could indicate the nature of anterior insula tissue injury in HF. The study aim was to assess anterior insular metabolites to determine processes mediating autonomic, pain, and neuropsychologic disruptions in HF. We performed magnetic resonance spectroscopy in bilateral anterior insulae in 11 HF and 53 controls, using a 3.0-Tesla magnetic resonance imaging scanner. Peaks for NAA at 2.02 ppm, Cr at 3.02 ppm, Cho at 3.2 ppm, and MI at 3.56 ppm were assigned, peak areas were calculated, and metabolites were expressed as ratios, including NAA/Cr, Cho/Cr, and MI/Cr. HF patients showed significantly increased Cho/Cr ratios, indicative of glial proliferation or injury, on the left anterior insula, and reduced NAA/Cr levels, suggesting neuronal loss/dysfunction, on the right anterior insula over controls. No differences in MI/Cr ratios appeared between groups. Right anterior insular neuronal loss and left glial alterations may contribute to distorted autonomic, pain, and neuropsychologic functions found in HF. Copyright © 2014 Elsevier B.V. All rights reserved.

Brain Metabolites in Autonomic Regulatory Insular Sites in Heart Failure

PubMed Central

Woo, Mary A.; Yadav, Santosh K.; Macey, Paul M.; Fonarow, Gregg C.; Harper, Ronald M.; Kumar, Rajesh

2014-01-01

Autonomic, pain, and neuropsychologic comorbidities appear in heart failure (HF), likely resulting from brain changes, indicated as loss of structural integrity and functional deficits. Among affected brain sites, the anterior insulae are prominent in serving major regulatory roles in many of the disrupted functions commonly seen in HF. Metabolite levels, including N-acetylaspartate (NAA), creatine (Cr), choline (Cho), and myo-inositol (MI), could indicate the nature of anterior insula tissue injury in HF. The study aim was to assess anterior insular metabolites to determine processes mediating autonomic, pain, and neuropsychologic disruptions in HF. We performed magnetic resonance spectroscopy in bilateral anterior insulae in 11 HF and 53 controls, using a 3.0-Tesla magnetic resonance imaging scanner. Peaks for NAA at 2.02ppm, Cr at 3.02ppm, Cho at 3.2ppm, and MI at 3.56ppm were assigned, peak areas calculated, and metabolites expressed as ratios, including NAA/Cr, Cho/Cr, and MI/Cr. HF patients showed significantly increased Cho/Cr ratios, indicative of glial proliferation or injury, on the left anterior insula, and reduced NAA/Cr levels, suggesting neuronal loss/dysfunction, on the right anterior insula over controls. No differences in MI/Cr ratios appeared between groups. Right anterior insular neuronal loss and left glial alterations may contribute to distorted autonomic, pain, and neuropsychologic functions found in HF. PMID:25248953

Experimental Study on Dynamic Mechanical Properties of 30CrMnSiNi2A Steel.

NASA Astrophysics Data System (ADS)

Huang, Fenglei; Yao, Wei; Wu, Haijun; Zhang, Liansheng

2009-06-01

Under dynamic conditions, the strain-rate dependence of material response and high levels of hydrostatic pressure cause the material behavior to be significantly different from what is observed under quasi-static condition. The curves of stress and strain of 30CrMnSiNi2A steel in different strain rates are obtained with SHPB experiments. Metallographic analyses show that 30CrMnSiNi2A steel is sensitive to strain rate, and dynamic compression leads to shear failure with the angle 45^o as the small carbide which precipitates around grain boundary changes the properties of 30CrMnSiNi2A steel. From the SHPB experiments and quasi-static results, the incomplete Johnson-Cook model has been obtained: σ=[1587+382.5(ɛ^p)^0.245][1+0.017ɛ^*], which can offer parameters for theory application and numerical simulation.

Evaluation of Varying Ductile Fracture Criteria for 42CrMo Steel by Compressions at Different Temperatures and Strain Rates

PubMed Central

Quan, Guo-zheng; Luo, Gui-chang; Mao, An; Liang, Jian-ting; Wu, Dong-sen

2014-01-01

Fracturing by ductile damage occurs quite naturally in metal forming processes, and ductile fracture of strain-softening alloy, here 42CrMo steel, cannot be evaluated through simple procedures such as tension testing. Under these circumstances, it is very significant and economical to find a way to evaluate the ductile fracture criteria (DFC) and identify the relationships between damage evolution and deformation conditions. Under the guidance of the Cockcroft-Latham fracture criteria, an innovative approach involving hot compression tests, numerical simulations, and mathematic computations provides mutual support to evaluate ductile damage cumulating process and DFC diagram along with deformation conditions, which has not been expounded by Cockcroft and Latham. The results show that the maximum damage value appears in the region of upsetting drum, while the minimal value appears in the middle region. Furthermore, DFC of 42CrMo steel at temperature range of 1123~1348 K and strain rate of 0.01~10 s−1 are not constant but change in a range of 0.160~0.226; thus, they have been defined as varying ductile fracture criteria (VDFC) and characterized by a function of temperature and strain rate. In bulk forming operations, VDFC help technicians to choose suitable process parameters and avoid the occurrence of fracture. PMID:24592175

Evaluation of varying ductile fracture criteria for 42CrMo steel by compressions at different temperatures and strain rates.

PubMed

Quan, Guo-zheng; Luo, Gui-chang; Mao, An; Liang, Jian-ting; Wu, Dong-sen

2014-01-01

Fracturing by ductile damage occurs quite naturally in metal forming processes, and ductile fracture of strain-softening alloy, here 42CrMo steel, cannot be evaluated through simple procedures such as tension testing. Under these circumstances, it is very significant and economical to find a way to evaluate the ductile fracture criteria (DFC) and identify the relationships between damage evolution and deformation conditions. Under the guidance of the Cockcroft-Latham fracture criteria, an innovative approach involving hot compression tests, numerical simulations, and mathematic computations provides mutual support to evaluate ductile damage cumulating process and DFC diagram along with deformation conditions, which has not been expounded by Cockcroft and Latham. The results show that the maximum damage value appears in the region of upsetting drum, while the minimal value appears in the middle region. Furthermore, DFC of 42CrMo steel at temperature range of 1123~1348 K and strain rate of 0.01~10 s(-1) are not constant but change in a range of 0.160~0.226; thus, they have been defined as varying ductile fracture criteria (VDFC) and characterized by a function of temperature and strain rate. In bulk forming operations, VDFC help technicians to choose suitable process parameters and avoid the occurrence of fracture.

Development of orally disintegrating tablets comprising controlled-release multiparticulate beads

PubMed Central

2012-01-01

Melperone is an atypical antipsychotic agent that has shown a wide spectrum of neuroleptic properties, particularly effective in the treatment of senile dementia and Parkinson’s-associated psychosis, and is marketed in Europe as an immediate-release (IR) tablet and syrup. An orally disintegrating tablet (ODT) dosage form would be advantageous for patients who experience difficulty in swallowing large tablets or capsules or those who experience dysphagia. Controlled-release (CR) capsule and ODT formulations containing melperone HCl were developed with target in vitro release profiles suitable for a once-daily dosing regimen. Both dosage forms allow for the convenient production of dose-proportional multiple strengths. Two ODT formulations exhibiting fast and medium release profiles and one medium release profile capsule formulation (each 50 mg) were tested in vivo using IR syrup as the reference. The two medium release formulations were shown to be bioequivalent to each other and are suitable for once-daily dosing. Based on the analytical and organoleptic test results, as well as the blend uniformity and in-process compression data at various compression forces using coated beads produced at one-tenth (1/10) commercial scale, both formulations in the form of CR capsules and CR ODTs have shown suitability for progression into further clinical development. PMID:22356215

Impact of lossy compression on diagnostic accuracy of radiographs for periapical lesions

NASA Technical Reports Server (NTRS)

Eraso, Francisco E.; Analoui, Mostafa; Watson, Andrew B.; Rebeschini, Regina

2002-01-01

OBJECTIVES: The purpose of this study was to evaluate the lossy Joint Photographic Experts Group compression for endodontic pretreatment digital radiographs. STUDY DESIGN: Fifty clinical charge-coupled device-based, digital radiographs depicting periapical areas were selected. Each image was compressed at 2, 4, 8, 16, 32, 48, and 64 compression ratios. One root per image was marked for examination. Images were randomized and viewed by four clinical observers under standardized viewing conditions. Each observer read the image set three times, with at least two weeks between each reading. Three pre-selected sites per image (mesial, distal, apical) were scored on a five-scale score confidence scale. A panel of three examiners scored the uncompressed images, with a consensus score for each site. The consensus score was used as the baseline for assessing the impact of lossy compression on the diagnostic values of images. The mean absolute error between consensus and observer scores was computed for each observer, site, and reading session. RESULTS: Balanced one-way analysis of variance for all observers indicated that for compression ratios 48 and 64, there was significant difference between mean absolute error of uncompressed and compressed images (P <.05). After converting the five-scale score to two-level diagnostic values, the diagnostic accuracy was strongly correlated (R (2) = 0.91) with the compression ratio. CONCLUSION: The results of this study suggest that high compression ratios can have a severe impact on the diagnostic quality of the digital radiographs for detection of periapical lesions.

Grain Refinement and Mechanical Properties of Cu-Cr-Zr Alloys with Different Nano-Sized TiCp Addition.

PubMed

Zhang, Dongdong; Bai, Fang; Wang, Yong; Wang, Jinguo; Wang, Wenquan

2017-08-08

The TiC p /Cu master alloy was prepared via thermal explosion reaction. Afterwards, the nano-sized TiC p /Cu master alloy was dispersed by electromagnetic stirring casting into the melting Cu-Cr-Zr alloys to fabricate the nano-sized TiC p -reinforced Cu-Cr-Zr composites. Results show that nano-sized TiC p can effectively refine the grain size of Cu-Cr-Zr alloys. The morphologies of grain in Cu-Cr-Zr composites changed from dendritic grain to equiaxed crystal because of the addition and dispersion of nano-sized TiC p . The grain size decreased from 82 to 28 μm with the nano-sized TiC p content. Compared with Cu-Cr-Zr alloys, the ultimate compressive strength (σ UCS ) and yield strength (σ 0.2 ) of 4 wt% TiC p -reinforced Cu-Cr-Zr composites increased by 6.7% and 9.4%, respectively. The wear resistance of the nano-sized TiCp-reinforced Cu-Cr-Zr composites increased with the increasing nano-sized TiCp content. The wear loss of the nano-sized TiC p -reinforced Cu-Cr-Zr composites decreased with the increasing TiC p content under abrasive particles. The eletrical conductivity of Cu-Cr-Zr alloys, 2% and 4% nano-sized TiCp-reinforced Cu-Cr-Zr composites are 64.71% IACS, 56.77% IACS and 52.93% IACS, respectively.

[Clinical application of proton magnetic resonance spectroscopy in children with idiopathic epilepsy].

PubMed

Shao, Xiao-Li; Zhou, Zhong-Shu; Hong, Wen

2010-06-01

This study examined the biochemical metabolism by proton magnetic resonance spectroscopy ('H-MRS) in order to explore the value of 'H-MRS in idiopathic epilepsy in children. Thirty-three children with idiopathic epilepsy (14 cases with history of febrile seizures and 19 cases without) and six normal controls experienced MRI of the skull and brain and single-voxel 'H-MRS examinations of the hippocampi-temporal lobe. The signal intensities of N-acetylaspartate (NAA), eatine+phosphocreatine (Cr), choline-containing compounds (Cho) and lactate (Lac) and the ratios of NAA/ (Cho+Cr) and Lac/Cr were compared between the patients and normal controls. MRI examination showed that only one child with epilepsy had myelin dysplasia. 'H-MRS examination showed that the ratio of NAA/ (Cho+Cr) in the epilepsy group was lower than that in the control group (0.64+/-0.07 vs 0.73+/-0.05; P<0.01). The epileptic children with history of febrile seizures had a more decreased ratio of NAA/ (Cho+Cr) compared with those without the history (0.61+/-0.07 vs 0.66+/-0.06; P<0.05). There were no significant differences in the ratio of Lac/Cr between the epilepsy and the control groups. 'H-MRS may provide early information on brain injury sensitively and non-invasively in children with epilepsy. It may be used for diagnosis and prognosis evaluation of epilepsy.

Evaluation of image compression for computer-aided diagnosis of breast tumors in 3D sonography

NASA Astrophysics Data System (ADS)

Chen, We-Min; Huang, Yu-Len; Tao, Chi-Chuan; Chen, Dar-Ren; Moon, Woo-Kyung

2006-03-01

Medical imaging examinations form the basis for physicians diagnosing diseases, as evidenced by the increasing use of digital medical images for picture archiving and communications systems (PACS). However, with enlarged medical image databases and rapid growth of patients' case reports, PACS requires image compression to accelerate the image transmission rate and conserve disk space for diminishing implementation costs. For this purpose, JPEG and JPEG2000 have been accepted as legal formats for the digital imaging and communications in medicine (DICOM). The high compression ratio is felt to be useful for medical imagery. Therefore, this study evaluates the compression ratios of JPEG and JPEG2000 standards for computer-aided diagnosis (CAD) of breast tumors in 3-D medical ultrasound (US) images. The 3-D US data sets with various compression ratios are compressed using the two efficacious image compression standards. The reconstructed data sets are then diagnosed by a previous proposed CAD system. The diagnostic accuracy is measured based on receiver operating characteristic (ROC) analysis. Namely, the ROC curves are used to compare the diagnostic performance of two or more reconstructed images. Analysis results ensure a comparison of the compression ratios by using JPEG and JPEG2000 for 3-D US images. Results of this study provide the possible bit rates using JPEG and JPEG2000 for 3-D breast US images.

Effect of load ratio and saltwater corrosive environment on the initiation life of fatigue of 10Ni5CrMoV steel

NASA Astrophysics Data System (ADS)

Xie, Xing; Yi, Hong; Xu, Jian; Gen, Liming; Chen, Luyun

2017-09-01

Fatigue initiation life has been studied with 10CrNi5MoV steel for use in ocean engineering at different load ratios and in different environmental media. The microstructure and micro-topography have been observed and analyzed by means of SEM, EDS and EBSD. Our findings indicate that, the initiation life of 10Ni5CrMoV steel in seawater is shorter than that in air, and the difference in longevity is larger with the increasing of load ratio. Corrosion pits had a great influence on initial corrosion fatigue life.

The Effect of Alkaline Activator Ratio on the Compressive Strength of Fly Ash-Based Geopolymer Paste

NASA Astrophysics Data System (ADS)

Lăzărescu, A. V.; Szilagyi, H.; Baeră, C.; Ioani, A.

2017-06-01

Alkaline activation of fly ash is a particular procedure in which ash resulting from a power plant combined with a specific alkaline activator creates a solid material when dried at a certain temperature. In order to obtain desirable compressive strengths, the mix design of fly ash based geopolymer pastes should be explored comprehensively. To determine the preliminary compressive strength for fly ash based geopolymer paste using Romanian material source, various ratios of Na2SiO3 solution/ NaOH solution were produced, keeping the fly ash/alkaline activator ratio constant. All the mixes were then cured at 70 °C for 24 hours and tested at 2 and 7 days, respectively. The aim of this paper is to present the preliminary compressive strength results for producing fly ash based geopolymer paste using Romanian material sources, the effect of alkaline activators ratio on the compressive strength and studying the directions for future research.

Strength development of pervious concrete containing engineered biomass aggregate

NASA Astrophysics Data System (ADS)

Sharif, A. A. M.; Shahidan, S.; Koh, H. B.; Kandash, A.; Zuki, S. S. Mohd

2017-11-01

Pervious concrete with high porosity has good permeability and low mechanical strengths are commonly used in controlling storm water management. It is different from normal concrete. It is only containing single size of coarse aggregate and has lower density compared with normal concrete. This study was focused on the effect of Engineered Biomass Aggregate (EBA) on the compressive strength, void ratio and water permeability of pervious concrete. EBA was prepared by coating the biomass aggregate with epoxy resin. EBA was used to replace natural coarse aggregate ranging from 0% to 25%. 150 mm cube specimens were prepared and used to study the compressive strength, void ratio and water permeability. Compressive strength was tested at 7, 14 and 28 days. Meanwhile, void ratio and permeability tests were carried out on 28 days. The experimental results showed that pervious concrete containing EBA gained lower compressive strength. The compressive strength was reduced gradually by increasing the percentage of EBA. Overall, Pervious concrete containing EBA achieved higher void ratio and permeability.

Parkinson's disease: in vivo metabolic changes in the frontal and parietal cortices in 6-OHDA treated rats during different periods.

PubMed

Hou, Zhongyu; Zhang, Zhonghe; Meng, Haiwei; Lin, Xiangtao; Sun, Bo; Lei, Hao; Fang, Ke; Fang, Fang; Liu, Maili; Liu, Shuwei

2014-02-01

This study aims to investigate metabolic changes in frontal and parietal cortices in the 6-OHDA induced Parkinson's rats. Ratios of N-acetyl-aspartic acid/creatine (NAA/Cr), choline/creatine (Cho/Cr), and glumatic acid and glutamine glutaminic acid/creatine (Glx/Cr) of regions of interests (ROIs) in the frontal and parietal cortices, and the substantia nigra were analyzed. NAA/Cr, Cho/Cr and Glx/Cr in the frontal and parietal cortices in the lesion side did not show any significant differences two weeks after operation compared with the contralateral side (p > 0.05). NAA/Cr in the frontal cortex in the lesion side was significantly lower in the five weeks after operation; Cho/Cr remained normal; Glx/Cr increased (p < 0.05), and all ratios of parietal cortex were normal. In the eight weeks after operation, NAA/Cr in the frontal cortex in the lesion side was lower than that of the five weeks (p < 0.01), Cho/Cr still remained normal while Glx/Cr was higher than before (p < 0.01). Regarding the parietal cortex, NAA/Cr increased significantly, while Cho/Cr and Glx/Cr remained normal. In the 12 weeks after operation, NAA/Cr, Cho/Cr and Glx/Cr in frontal cortex were consistent with that of the eight weeks, while they remained at the normal level in parietal cortex. The NAA/Cr in the substantia nigra decreased and Cho/Cr increased significantly during 2-8 weeks, and remained at the same level during 8-12 weeks. There are metabolic disturbances in PD rats. The transient hyperfunction in the parietal cortex can be considered as a compensation for the dysfunction of the frontal cortex and substantia nigra.

Urinary Uric Acid/Creatinine Ratio - A Marker For Perinatal Asphyxia.

PubMed

Patel, Kinjal Prahaladbhai; Makadia, Mayur Goradhanbhai; Patel, Vishwal Indravardan; Nilayangode, Haridas Neelakandan; Nimbalkar, Somashekhar Marutirao

2017-01-01

Perinatal hypoxia is one of the leading causes of perinatal mortality in developing countries. Both apgar score and arterial blood pH predict the neonatal mortality in asphyxia. Apgar score alone does not predict neurologic outcome and as it is influenced by various factors. This study was conducted to evaluate the utility and sensitivity of urinary uric acid to creatinine ratio (UA/Cr ratio) in asphyxia diagnosis, compared to invasive Arterial Blood Gas (ABG) analysis. To assess the urinary uric acid/creatinine ratio as an additional marker for perinatal asphyxia compared with ABG analysis in apgar score monitoring. The present case control study was conducted at a teaching hospital in Central Gujarat. Data of 40 healthy newborns and 40 asphyxiated newborns were collected. In absence of regional estimates, a sample of size 39 was required to attain a power of 80% at 5% alpha (type I error) considering a moderate effect size of 0.65. (UA/Cr) ratio was measured from the spot urine sample collected during 24-72 hours of birth. Statistical analysis was performed by Independent t-test, Pearson's correlation coefficient (r) and Receiver Operating Characteristic (ROC) plots. The mean (UA/Cr ratio) (2.75±0.18 vs 1.78±0.23) is significantly higher in asphyxiated group than in the control group (p<0.0001). Urinary UA/Cr ratio had negative correlation with blood pH (r= -0.27, p=0.18), which was not significant (p>0.05). Urinary UA/Cr ratio with criterion of >2.3 had 100% sensitivity, 100% specificity with AUC of 1 (p<0.0001) had a better predictive value. Apgar score is usually reduced in neonates with congenital anomalies and premature neonates. Hence, it is preferable that the clinical diagnosis of asphyxia by apgar scores be supported by other investigations so that early decision can be taken about the level of care the baby needs. pH, lactates and base deficits change with establishment of respiration following resuscitation. However, pH, lactate, base deficit estimations are invasive and need rapid estimations. Non-invasive urinary UA/Cr ratio may be an answer to these issues as it easy, economical and equally efficient.

A novel color image compression algorithm using the human visual contrast sensitivity characteristics

NASA Astrophysics Data System (ADS)

Yao, Juncai; Liu, Guizhong

2017-03-01

In order to achieve higher image compression ratio and improve visual perception of the decompressed image, a novel color image compression scheme based on the contrast sensitivity characteristics of the human visual system (HVS) is proposed. In the proposed scheme, firstly the image is converted into the YCrCb color space and divided into sub-blocks. Afterwards, the discrete cosine transform is carried out for each sub-block, and three quantization matrices are built to quantize the frequency spectrum coefficients of the images by combining the contrast sensitivity characteristics of HVS. The Huffman algorithm is used to encode the quantized data. The inverse process involves decompression and matching to reconstruct the decompressed color image. And simulations are carried out for two color images. The results show that the average structural similarity index measurement (SSIM) and peak signal to noise ratio (PSNR) under the approximate compression ratio could be increased by 2.78% and 5.48%, respectively, compared with the joint photographic experts group (JPEG) compression. The results indicate that the proposed compression algorithm in the text is feasible and effective to achieve higher compression ratio under ensuring the encoding and image quality, which can fully meet the needs of storage and transmission of color images in daily life.

Tensile and compressive failure modes of laminated composites loaded by fatigue with different mean stress

NASA Technical Reports Server (NTRS)

Rotem, Assa

1990-01-01

Laminated composite materials tend to fail differently under tensile or compressive load. Under tension, the material accumulates cracks and fiber fractures, while under compression, the material delaminates and buckles. Tensile-compressive fatigue may cause either of these failure modes depending on the specific damage occurring in the laminate. This damage depends on the stress ratio of the fatigue loading. Analysis of the fatigue behavior of the composite laminate under tension-tension, compression-compression, and tension-compression had led to the development of a fatigue envelope presentation of the failure behavior. This envelope indicates the specific failure mode for any stress ratio and number of loading cycles. The construction of the fatigue envelope is based on the applied stress-cycles to failure (S-N) curves of both tensile-tensile and compressive-compressive fatigue. Test results are presented to verify the theoretical analysis.

The predictive value of baseline NAA/Cr for treatment response of first-episode schizophrenia: A ¹H MRS study.

PubMed

Liu, Weibo; Yu, Hualiang; Jiang, Biao; Pan, Bing; Yu, Shaohua; Li, Huichun; Zheng, Leilei

2015-07-23

The study focused on the predictive value of baseline metabolite ratios in bilateral hippocampus of first-episode schizophrenia by using proton magnetic resonance spectroscopy ((1)H MRS). (1)H MRS data were acquired from 23 hallucination and 17 non-hallucination first-episode schizophrenia patients compared with 17 healthy participants. Clinical characteristics of patients were rated using the Positive and Negative Syndrome Scale (PANSS) before and after 3-month treatment. The schizophrenia patients showed lower NAA/Cr ratio than healthy participants respectively (p=0.024; p=0.001), and non-hallucination patients had even lower NAA/Cr ratio than hallucination patients (p=0.033). After 3-month treatment, hallucination patients had greater improvement in negative symptoms than non-hallucination patients (p=0.018). The reduction of PANSS total score and negative factor score was positively correlated with the left NAA/Cr in both group patients (p<0.05). Given that the bilateral hippocampal baseline NAA/Cr had predictive value for the whole treatment response, and the left hippocampal NAA/Cr can predict the prognosis of negative symptoms during acute phase medication in first-episode schizophrenia. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Pathologic Complete Response Predicts Recurrence-Free Survival More Effectively by Cancer Subset: Results From the I-SPY 1 TRIAL—CALGB 150007/150012, ACRIN 6657

PubMed Central

Esserman, Laura J.; Berry, Donald A.; DeMichele, Angela; Carey, Lisa; Davis, Sarah E.; Buxton, Meredith; Hudis, Cliff; Gray, Joe W.; Perou, Charles; Yau, Christina; Livasy, Chad; Krontiras, Helen; Montgomery, Leslie; Tripathy, Debasish; Lehman, Constance; Liu, Minetta C.; Olopade, Olufunmilayo I.; Rugo, Hope S.; Carpenter, John T.; Dressler, Lynn; Chhieng, David; Singh, Baljit; Mies, Carolyn; Rabban, Joseph; Chen, Yunn-Yi; Giri, Dilip; van 't Veer, Laura; Hylton, Nola

2012-01-01

Purpose Neoadjuvant chemotherapy for breast cancer provides critical information about tumor response; how best to leverage this for predicting recurrence-free survival (RFS) is not established. The I-SPY 1 TRIAL (Investigation of Serial Studies to Predict Your Therapeutic Response With Imaging and Molecular Analysis) was a multicenter breast cancer study integrating clinical, imaging, and genomic data to evaluate pathologic response, RFS, and their relationship and predictability based on tumor biomarkers. Patients and Methods Eligible patients had tumors ≥ 3 cm and received neoadjuvant chemotherapy. We determined associations between pathologic complete response (pCR; defined as the absence of invasive cancer in breast and nodes) and RFS, overall and within receptor subsets. Results In 221 evaluable patients (median tumor size, 6.0 cm; median age, 49 years; 91% classified as poor risk on the basis of the 70-gene prognosis profile), 41% were hormone receptor (HR) negative, and 31% were human epidermal growth factor receptor 2 (HER2) positive. For 190 patients treated without neoadjuvant trastuzumab, pCR was highest for HR-negative/HER2-positive patients (45%) and lowest for HR-positive/HER2-negative patients (9%). Achieving pCR predicted favorable RFS. For 172 patients treated without trastuzumab, the hazard ratio for RFS of pCR versus no pCR was 0.29 (95% CI, 0.07 to 0.82). pCR was more predictive of RFS by multivariate analysis when subtype was taken into account, and point estimates of hazard ratios within the HR-positive/HER2-negative (hazard ratio, 0.00; 95% CI, 0.00 to 0.93), HR-negative/HER2-negative (hazard ratio, 0.25; 95% CI, 0.04 to 0.97), and HER2-positive (hazard ratio, 0.14; 95% CI, 0.01 to 1.0) subtypes are lower. Ki67 further improved the prediction of pCR within subsets. Conclusion In this biologically high-risk group, pCR differs by receptor subset. pCR is more highly predictive of RFS within every established receptor subset than overall, demonstrating that the extent of outcome advantage conferred by pCR is specific to tumor biology. PMID:22649152

Brain metabolic correlates of decision making in amnestic mild cognitive impairment.

PubMed

Griffith, H Randall; Okonkwo, Ozioma C; den Hollander, Jan A; Belue, Katherine; Copeland, Jacqueline; Harrell, Lindy E; Brockington, John C; Clark, David G; Marson, Daniel C

2010-01-01

Persons with amnestic mild cognitive impairment (MCI) have subtle impairments in medical decision-making capacity (MDC). We examined the relationship between proton magnetic resonance spectroscopy (MRS) and MDC in MCI. Twenty-nine MCI patients and 42 controls underwent MRS to obtain ratios of N-acetylaspartate (NAA)/Creatine (Cr), Choline (Cho)/Cr, and myo-Inositol (mI)/Cr of the posterior cingulate. They also completed the Capacity to Consent to Treatment Instrument (CCTI), a vignette-based instrument measuring decisional standards of expressing choice, appreciating consequences of choice, providing rational reasons for choice, and understanding treatment choices. Patients showed abnormal MRS ratios of mI/Cr and Cho/Cr compared to controls, and impairments on the CCTI understanding and reasoning Standards. Performance on the reasoning standard of the CCTI was correlated with NAA/Cr (r = .46, p < .05). The relationship of NAA/Cr with decision-making suggests a role for posterior cortical neuronal functioning in performance of complex IADLs in MCI.

A new efficient method for color image compression based on visual attention mechanism

NASA Astrophysics Data System (ADS)

Shao, Xiaoguang; Gao, Kun; Lv, Lily; Ni, Guoqiang

2010-11-01

One of the key procedures in color image compression is to extract its region of interests (ROIs) and evaluate different compression ratios. A new non-uniform color image compression algorithm with high efficiency is proposed in this paper by using a biology-motivated selective attention model for the effective extraction of ROIs in natural images. When the ROIs have been extracted and labeled in the image, the subsequent work is to encode the ROIs and other regions with different compression ratios via popular JPEG algorithm. Furthermore, experiment results and quantitative and qualitative analysis in the paper show perfect performance when comparing with other traditional color image compression approaches.

X-ray fluorescence analysis of Cr(6+) component in mixtures of Cr(2)O(3) and K(2)CrO(4).

PubMed

Tochio, Tatsunori; Sakakura, Shusuke; Oohashi, Hirofumi; Mizota, Hirohisa; Zou, Yanhui; Ito, Yoshiaki; Fukushima, Sei; Tanuma, Shigeo; Shoji, Takashi; Fujimura, Hajime; Yamashita, Michiru

2010-01-01

X-ray fluorescence analysis using Cr K(alpha) spectra was applied to the determination of the mixing ratio of Cr(6+) to (Cr(6+) + Cr(3+)) in several mixtures of K(2)CrO(4) and Cr(2)O(3). Because the powder of K(2)CrO(4) contained large particles that were more than 50 microm in diameter, it was ground between a pestle and a mortar for about 8 h. The coarse particles still remaining were removed by using a sieve with 325-mesh (44 microm) in order to reduce the difference in absorption effects between emissions from Cr(6+) and those from Cr(3+). The mixing ratio, K(2)CrO(4)/(K(2)CrO(4) + Cr(2)O(3)), of the five mixtures investigated is 0.50, 0.40, 0.20, 0.10, and 0.05 in weight, respectively. Each spectrum obtained was analyzed by decomposing it into two reference spectra, those of the two pure materials, K(2)CrO(4) and Cr(2)O(3), with a constant background. The results for the mixtures containing K(2)CrO(4) of more than 20 wt% are that the relative deviation from the true value is less than approximately 5%. On the other hand, when the content of K(2)CrO(4) decreases to less than 10 wt%, the relative deviation gets so large as 20 - 25%. The error coming from a peak separation of spectrum involved in our results were estimated by applying our method to five sets of data for each mixture computationally generated, taking into account the uncertainty in total counts of real measurements.

Radiological Image Compression

NASA Astrophysics Data System (ADS)

Lo, Shih-Chung Benedict

The movement toward digital images in radiology presents the problem of how to conveniently and economically store, retrieve, and transmit the volume of digital images. Basic research into image data compression is necessary in order to move from a film-based department to an efficient digital -based department. Digital data compression technology consists of two types of compression technique: error-free and irreversible. Error -free image compression is desired; however, present techniques can only achieve compression ratio of from 1.5:1 to 3:1, depending upon the image characteristics. Irreversible image compression can achieve a much higher compression ratio; however, the image reconstructed from the compressed data shows some difference from the original image. This dissertation studies both error-free and irreversible image compression techniques. In particular, some modified error-free techniques have been tested and the recommended strategies for various radiological images are discussed. A full-frame bit-allocation irreversible compression technique has been derived. A total of 76 images which include CT head and body, and radiographs digitized to 2048 x 2048, 1024 x 1024, and 512 x 512 have been used to test this algorithm. The normalized mean -square-error (NMSE) on the difference image, defined as the difference between the original and the reconstructed image from a given compression ratio, is used as a global measurement on the quality of the reconstructed image. The NMSE's of total of 380 reconstructed and 380 difference images are measured and the results tabulated. Three complex compression methods are also suggested to compress images with special characteristics. Finally, various parameters which would effect the quality of the reconstructed images are discussed. A proposed hardware compression module is given in the last chapter.

Heterogeneous Distribution of Chromium on Mercury

NASA Astrophysics Data System (ADS)

Nittler, L. R.; Boujibar, A.; Crapster-Pregont, E.; Frank, E. A.; McCoy, T. J.; McCubbin, F. M.; Starr, R. D.; Vander Kaaden, K. E.; Vorburger, A.; Weider, S. Z.

2018-05-01

Mercury's surface has an average Cr/Si ratio of 0.003 (Cr 800 ppm), with at least a factor of 2 systematic uncertainty. Cr is heterogeneously distributed and correlated with Mg, Ca, S, and Fe and anti-correlated with Al.

Compression mechanisms in the plasma focus pinch

NASA Astrophysics Data System (ADS)

Lee, S.; Saw, S. H.; Ali, Jalil

2017-03-01

The compression of the plasma focus pinch is a dynamic process, governed by the electrodynamics of pinch elongation and opposed by the negative rate of change of current dI/dt associated with the current dip. The compressibility of the plasma is influenced by the thermodynamics primarily the specific heat ratio; with greater compressibility as the specific heat ratio γ reduces with increasing degree of freedom f of the plasma ensemble due to ionization energy for the higher Z (atomic number) gases. The most drastic compression occurs when the emitted radiation of a high-Z plasma dominates the dynamics leading in extreme cases to radiative collapse which is terminated only when the compressed density is sufficiently high for the inevitable self-absorption of radiation to occur. We discuss the central pinch equation which contains the basic electrodynamic terms with built-in thermodynamic factors and a dQ/dt term; with Q made up of a Joule heat component and absorption-corrected radiative terms. Deuterium is considered as a thermodynamic reference (fully ionized perfect gas with f = 3) as well as a zero-radiation reference (bremsstrahlung only; with radiation power negligible compared with electrodynamic power). Higher Z gases are then considered and regimes of thermodynamic enhancement of compression are systematically identified as are regimes of radiation-enhancement. The code which incorporates all these effects is used to compute pinch radius ratios in various gases as a measure of compression. Systematic numerical experiments reveal increasing severity in radiation-enhancement of compressions as atomic number increases. The work progresses towards a scaling law for radiative collapse and a generalized specific heat ratio incorporating radiation.

THE B/C AND SUB-IRON/IRON COSMIC RAY RATIOS—FURTHER EVIDENCE IN FAVOR OF THE SPIRAL-ARM DIFFUSION MODEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benyamin, David; Piran, Tsvi; Shaviv, Nir J.

The boron to carbon (B/C) and sub-Fe/Fe ratios provide an important clue on cosmic ray (CR) propagation within the Galaxy. These ratios estimate the grammage that the CRs traverse as they propagate from their sources to Earth. Attempts to explain these ratios within the standard CR propagation models require ad hoc modifications and even with those these models necessitate inconsistent grammages to explain both ratios. As an alternative, physically motivated model, we have proposed that CRs originate preferably within the galactic spiral arms. CR propagation from dynamic spiral arms has important imprints on various secondary to primary ratios, such asmore » the B/C ratio and the positron fraction. We use our spiral-arm diffusion model with the spallation network extended up to nickel to calculate the sub-Fe/Fe ratio. We show that without any additional parameters the spiral-arm model consistently explains both ratios with the same grammage, providing further evidence in favor of this model.« less

Learning random networks for compression of still and moving images

NASA Technical Reports Server (NTRS)

Gelenbe, Erol; Sungur, Mert; Cramer, Christopher

1994-01-01

Image compression for both still and moving images is an extremely important area of investigation, with numerous applications to videoconferencing, interactive education, home entertainment, and potential applications to earth observations, medical imaging, digital libraries, and many other areas. We describe work on a neural network methodology to compress/decompress still and moving images. We use the 'point-process' type neural network model which is closer to biophysical reality than standard models, and yet is mathematically much more tractable. We currently achieve compression ratios of the order of 120:1 for moving grey-level images, based on a combination of motion detection and compression. The observed signal-to-noise ratio varies from values above 25 to more than 35. The method is computationally fast so that compression and decompression can be carried out in real-time. It uses the adaptive capabilities of a set of neural networks so as to select varying compression ratios in real-time as a function of quality achieved. It also uses a motion detector which will avoid retransmitting portions of the image which have varied little from the previous frame. Further improvements can be achieved by using on-line learning during compression, and by appropriate compensation of nonlinearities in the compression/decompression scheme. We expect to go well beyond the 250:1 compression level for color images with good quality levels.

Accurate classical short-range forces for the study of collision cascades in Fe–Ni–Cr

DOE PAGES

Béland, Laurent Karim; Tamm, Artur; Mu, Sai; ...

2017-05-10

The predictive power of a classical molecular dynamics simulation is largely determined by the physical validity of its underlying empirical potential. In the case of high-energy collision cascades, it was recently shown that correctly modeling interactions at short distances is necessary to accurately predict primary damage production. An ab initio based framework is introduced for modifying an existing embedded-atom method FeNiCr potential to handle these short-range interactions. Density functional theory is used to calculate the energetics of two atoms approaching each other, embedded in the alloy, and to calculate the equation of state of the alloy as it is compressed.more » The pairwise terms and the embedding terms of the potential are modi ed in accordance with the ab initio results. Using this reparametrized potential, collision cascades are performed in Ni 50Fe 50, Ni 80Cr 20 and Ni 33Fe 33Cr 33. The simulations reveal that alloying Ni and NiCr to Fe reduces primary damage production, in agreement with some previous calculations. Alloying Ni and NiFe to Cr does not reduce primary damage production, in contradiction with previous calculations.« less

Temperature Dependent Electrical Transport Properties of Ni-Cr and Co-Cr Binary Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thakore, B. Y.; Khambholja, S. G.; Bhatt, N. K.

2011-12-12

The temperature dependent electrical transport properties viz. electrical resistivity and thermal conductivity of Ni{sub 10}Cr{sub 90} and Co{sub 20}Cr{sub 80} alloys are computed at various temperatures. The electrical resistivity has been calculated according to Faber-Ziman model combined with Ashcroft-Langreth partial structure factors. In the present work, to include the ion-electron interaction, we have used a well tested local model potential. For exchange-correlation effects, five different forms of local field correction functions due to Hartree (H), Taylor (T), Ichimaru and Utsumi (IU), Farid et al (F) and Sarkar et al (S) are used. The present results due to S function aremore » in good agreement with the experimental data as compared to results obtained using other four functions. The S functions satisfy compressibility sum rule in long wave length limit more accurately as compared to T, IU and F functions, which may be responsible for better agreement of results, obtained using S function. Also, present result confirms the validity of present approach in determining the transport properties of alloys like Ni-Cr and Co-Cr.« less

Characterization of Cr poisoning in a solid oxide fuel cell cathode using a high-energy x-ray microbeam.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, D. J.; Almer, J.; Cruse, T.

2010-01-01

A key feature of planar solid oxide fuel cells (SOFCs) is the feasibility of using metallic interconnects made of high temperature ferritic stainless steels, which reduce system cost while providing excellent electric conductivity. Such interconnects, however, contain high levels of chromium, which has been found to be associated with SOFC cathode performance degradation at SOFC operating temperatures; a phenomenon known as Cr poisoning. Here, we demonstrate an accurate measurement of the phase and concentration distributions of Cr species in a degraded SOFC, as well as related properties including deviatoric strain, integrated porosity, and lattice parameter variation, using high energy microbeammore » X-ray diffraction and radiography. We unambiguously identify (MnCr){sub 3}O{sub 4} and Cr{sub 2}O{sub 3} as the two main contaminant phases and find that their concentrations correlate strongly with the cathode layer composition. Cr{sub 2}O{sub 3} deposition within the active cathode region reduces porosity and produces compressive residual strains, which hinders the reactant gas percolation and can cause structural breakdown of the SOFC cathode. The information obtained through this study can be used to better understand the Cr-poisoning mechanism and improve SOFC design.« less

Imaging increased glutamate in children with Sturge-Weber syndrome: Association with epilepsy severity.

PubMed

Juhász, Csaba; Hu, Jiani; Xuan, Yang; Chugani, Harry T

2016-05-01

Sturge-Weber syndrome (SWS) is strongly associated with epilepsy. Brain tissue studies have suggested that epileptic activity in SWS is driven by glutamatergic synaptic activity. Here, we used proton magnetic resonance spectroscopic imaging (MRSI) to test if glutamate (GLU) concentrations are increased in the affected hemisphere and if such increases are associated with severity of epilepsy in children with SWS. We also studied the metabolic correlates of MRSI abnormalities, using glucose positron emission tomography (PET) imaging. 3T MRI and glucose PET were performed in 10 children (age: 7-78 months) with unilateral SWS and a history of epilepsy. MRSI data were acquired from the affected (ipsilateral) and non-affected (contralateral) hemispheres. GLU, N-acetyl-aspartate (NAA) and creatine (Cr) were quantified in multiple voxels; GLU/Cr and NAA/Cr ratios were calculated and compared to seizure frequency as well as glucose PET findings. The highest GLU/Cr ratios were found in the affected hemisphere in all children except one with severe atrophy. The maximum ipsilateral/contralateral GLU/Cr ratios ranged between 1.0 and 2.5 (mean: 1.6). Mean ipsilateral/contralateral GLU/Cr ratios were highest in the youngest children and showed a strong positive correlation with clinical seizure frequency scores assessed at the time of the scan (r=0.88, p=0.001) and also at follow-up (up to 1 year, r=0.80, p=0.009). GLU increases in the affected hemisphere coincided with areas showing current or previous increases of glucose metabolism on PET in 5 children. NAA/Cr ratios showed no association with clinical seizure frequency. Increased glutamate concentrations in the affected hemisphere, measured by MRSI, are common in young children with unilateral SWS and are associated with frequent seizures. The findings lend support to the role of excess glutamate in SWS-associated epilepsy. Copyright © 2016 Elsevier B.V. All rights reserved.

Flow and compaction properties of hypromellose: new directly compressible versus the established grades.

PubMed

Grdešič, Peter; Vrečer, Franc; Ilić, Ilija

2016-11-01

Information about flow and compaction properties of hypromellose (HPMC) polymers is essential for the technologists who are facing challenges regarding poor flow and compaction while developing new controlled release matrix tablets. There is a profound lack of studies in this field and none of the published ones deal with the compaction of the newly introduced HPMC grades specifically designed for direct compression (DC). The objective behind this study was the evaluation of flow and compaction properties of six different grades of HPMC substitution type 2208 polymers, including two second generation directly compressible grades from Dow Chemical Company (K100LV, K15M, K4M CR, K4M DC, K100M CR and K100M DC). Flow properties were determined using flow time and Carr index. Compaction properties were quantified using "out-of-die" Heckel and modified Walker models as well as tensile strength profile and elastic recovery. We used statistical approach to analyze the results. Due to larger, rounder and smoother particles both DC grades showed distinctly better flow properties compared to their non-DC counterparts. Overall, K15M showed the best compaction properties, closely followed by K100LV. K100M grades showed superior compaction properties over K4M grades. The new, second generation DC grades had poorer compaction properties, however, they exhibited better flow properties on the other hand. Considering all compaction results, the Heckel model gave better description of compressibility compared to the Walker model, so it may be preferred in case of studying HPMC polymers and other similar materials.

Spectral dependence of backscattering coefficient of mixed phase clouds over West Africa measured with two-wavelength Raman polarization lidar: Features attributed to ice-crystals corner reflection

NASA Astrophysics Data System (ADS)

Veselovskii, I.; Goloub, P.; Podvin, T.; Tanre, D.; Ansmann, A.; Korenskiy, M.; Borovoi, A.; Hu, Q.; Whiteman, D. N.

2017-11-01

The existing models predict that corner reflection (CR) of laser radiation by simple ice crystals of perfect shape, such as hexagonal columns or plates, can provide a significant contribution to the ice cloud backscattering. However in real clouds the CR effect may be suppressed due to crystal deformation and surface roughness. In contrast to the extinction coefficient, which is spectrally independent, consideration of diffraction associated with CR results in a spectral dependence of the backscattering coefficient. Thus measuring the spectral dependence of the cloud backscattering coefficient, the contribution of CR can be identified. The paper presents the results of profiling of backscattering coefficient (β) and particle depolarization ratio (δ) of ice and mixed-phase clouds over West Africa by means of a two-wavelength polarization Mie-Raman lidar operated at 355 nm and 532 nm during the SHADOW field campaign. The lidar observations were performed at a slant angle of 43 degree off zenith, thus CR from both randomly oriented crystals and oriented plates could be analyzed. For the most of the observations the cloud backscatter color ratio β355/β532 was close to 1.0, and no spectral features that might indicate the presence of CR of randomly oriented crystals were revealed. Still, in two measurement sessions we observed an increase of backscatter color ratio to a value of nearly 1.3 simultaneously with a decrease of the spectral depolarization ratio δ355/δ532 ratio from 1.0 to 0.8 inside the layers containing precipitating ice crystals. We attribute these changes in optical properties to corner reflections by horizontally oriented ice plates.

Structural and Visible-Near Infrared Optical Properties of Cr-Doped TiO2 for Colored Cool Pigments

NASA Astrophysics Data System (ADS)

Yuan, Le; Weng, Xiaolong; Zhou, Ming; Zhang, Qingyong; Deng, Longjiang

2017-11-01

Chromium-doped TiO2 pigments were synthesized via a solid-state reaction method and studied with X-ray diffraction, SEM, XPS, and UV-VIS-NIR reflectance spectroscopy. The incorporation of Cr3+ accelerates the transition from the anatase phase to the rutile phase and compresses the crystal lattice. Moreover, the particle morphology, energy gap, and reflectance spectrum of Cr-doped TiO2 pigments is affected by the crystal structure and doping concentration. For the rutile samples, some of the Cr3+ ions are oxidized to Cr4+ after sintering at a high temperature, which leads to a strong near-infrared absorption band due to the 3A2 → 3 T1 electric dipole-allowed transitions of Cr4+. And the decrease of the band gap causes an obvious redshift of the optical absorption edges as the doping concentration increases. Thus, the VIS and near-infrared average reflectance of the rutile Ti1 - x Cr x O2 sample decrease by 60.2 and 58%, respectively, when the Cr content increases to x = 0.0375. Meanwhile, the color changes to black brown. However, for the anatase Ti1 - x Cr x O2 pigments, only the VIS reflection spectrum is inhibited by forming some characteristic visible light absorption peaks of Cr3+. The morphology, band gap, and NIR reflectance are not significantly affected. Finally, a Cr-doped anatase TiO2 pigment with a brownish-yellow color and 90% near-infrared reflectance can be obtained.

Implications of Fast Reactor Transuranic Conversion Ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven J. Piet; Edward A. Hoffman; Samuel E. Bays

2010-11-01

Theoretically, the transuranic conversion ratio (CR), i.e. the transuranic production divided by transuranic destruction, in a fast reactor can range from near zero to about 1.9, which is the average neutron yield from Pu239 minus 1. In practice, the possible range will be somewhat less. We have studied the implications of transuranic conversion ratio of 0.0 to 1.7 using the fresh and discharge fuel compositions calculated elsewhere. The corresponding fissile breeding ratio ranges from 0.2 to 1.6. The cases below CR=1 (“burners”) do not have blankets; the cases above CR=1 (“breeders”) have breeding blankets. The burnup was allowed to floatmore » while holding the maximum fluence to the cladding constant. We graph the fuel burnup and composition change. As a function of transuranic conversion ratio, we calculate and graph the heat, gamma, and neutron emission of fresh fuel; whether the material is “attractive” for direct weapon use using published criteria; the uranium utilization and rate of consumption of natural uranium; and the long-term radiotoxicity after fuel discharge. For context, other cases and analyses are included, primarily once-through light water reactor (LWR) uranium oxide fuel at 51 MWth-day/kg-iHM burnup (UOX-51). For CR<1, the heat, gamma, and neutron emission increase as material is recycled. The uranium utilization is at or below 1%, just as it is in thermal reactors as both types of reactors require continuing fissile support. For CR>1, heat, gamma, and neutron emission decrease with recycling. The uranium utilization exceeds 1%, especially as all the transuranic elements are recycled. exceeds 1%, especially as all the transuranic elements are recycled. At the system equilibrium, heat and gamma vary by somewhat over an order of magnitude as a function of CR. Isotopes that dominate heat and gamma emission are scattered throughout the actinide chain, so the modest impact of CR is unsurprising. Neutron emitters are preferentially found among the higher actinides, so the neutron emission varies much stronger with CR, about three orders of magnitude.« less

An Image Processing Technique for Achieving Lossy Compression of Data at Ratios in Excess of 100:1

DTIC Science & Technology

1992-11-01

5 Lempel , Ziv , Welch (LZW) Compression ............... 7 Lossless Compression Tests Results ................. 9 Exact...since IBM holds the patent for this technique. Lempel , Ziv , Welch (LZW) Compression The LZW compression is related to two compression techniques known as... compression , using the input stream as data . This step is possible because the compression algorithm always outputs the phrase and character components of a

Basic life support with four different compression/ventilation ratios in a pig model: the need for ventilation.

PubMed

Kill, Clemens; Torossian, Alexander; Freisburger, Christian; Dworok, Sebastian; Massmann, Martin; Nohl, Thorsten; Henning, Ronald; Wallot, Pascal; Gockel, Andreas; Steinfeldt, Thorsten; Graf, Jürgen; Eberhart, Leopold; Wulf, Hinnerk

2009-09-01

During cardiac arrest the paramount goal of basic life support (BLS) is the oxygenation of vital organs. Current recommendations are to combine chest compressions with ventilation in a fixed ratio of 30:2; however the optimum compression/ventilation ratio is still debatable. In our study we compared four different compression/ventilation ratios and documented their effects on the return of spontaneous circulation (ROSC), gas exchange, cerebral tissue oxygenation and haemodynamics in a pig model. Study was performed on 32 pigs under general anaesthesia with endotracheal intubation. Arterial and central venous lines were inserted. For continuous cerebral tissue oxygenation a Licox PtiO(2) probe was implanted. After 3 min of cardiac arrest (ventricular fibrillation) animals were randomized to a compression/ventilation-ratio 30:2, 100:5, 100:2 or compressions-only. Subsequently 10 min BLS, Advanced Life Support (ALS) was performed (100%O(2), 3 defibrillations, 1mg adrenaline i.v.). Data were analyzed with 2-factorial ANOVA. ROSC was achieved in 4/8 (30:2), 5/8 (100:5), 2/8 (100:2) and 0/8 (compr-only) pigs. During BLS, PaCO(2) increased to 55 mm Hg (30:2), 68 mm Hg (100:5; p=0.0001), 66 mm Hg (100:2; p=0.002) and 72 mm Hg (compr-only; p<0.0001). PaO(2) decreased to 58 mmg (30:2), 40 mm Hg (100:5; p=0.15), 43 mm Hg (100:2; p=0.04) and 26 mm Hg (compr-only; p<0.0001). PtiO(2) baseline values were 12.7, 12.0, 11.1 and 10.0 mm Hg and decreased to 8.1 mm Hg (30:2), 4.1 mm Hg (100:5; p=0.08), 4.3 mm Hg (100:2; p=0.04), and 4.5 mm Hg (compr-only; p=0.69). During BLS, a compression/ventilation-ratio of 100:5 seems to be equivalent to 30:2, while ratios of 100:2 or compressions-only detoriate peripheral arterial oxygenation and reduce the chance for ROSC.

A database for assessment of effect of lossy compression on digital mammograms

NASA Astrophysics Data System (ADS)

Wang, Jiheng; Sahiner, Berkman; Petrick, Nicholas; Pezeshk, Aria

2018-03-01

With widespread use of screening digital mammography, efficient storage of the vast amounts of data has become a challenge. While lossless image compression causes no risk to the interpretation of the data, it does not allow for high compression rates. Lossy compression and the associated higher compression ratios are therefore more desirable. The U.S. Food and Drug Administration (FDA) currently interprets the Mammography Quality Standards Act as prohibiting lossy compression of digital mammograms for primary image interpretation, image retention, or transfer to the patient or her designated recipient. Previous work has used reader studies to determine proper usage criteria for evaluating lossy image compression in mammography, and utilized different measures and metrics to characterize medical image quality. The drawback of such studies is that they rely on a threshold on compression ratio as the fundamental criterion for preserving the quality of images. However, compression ratio is not a useful indicator of image quality. On the other hand, many objective image quality metrics (IQMs) have shown excellent performance for natural image content for consumer electronic applications. In this paper, we create a new synthetic mammogram database with several unique features. We compare and characterize the impact of image compression on several clinically relevant image attributes such as perceived contrast and mass appearance for different kinds of masses. We plan to use this database to develop a new objective IQM for measuring the quality of compressed mammographic images to help determine the allowed maximum compression for different kinds of breasts and masses in terms of visual and diagnostic quality.

Parametric study on the compressive strength geopolymer paving block

NASA Astrophysics Data System (ADS)

Aman; Awaluddin, A.; Ahmad, A.; Olivia, M.

2018-04-01

This paper reported about the investigated of sodium hidroxida concentration, effect of ratio liquid to solid (L/S), temperature and time on the compressive strength of geopolymer paving block using fly ash and fine aggregate as base material and combination of sodium hidroxida and sodium silicate as alkaline activator and the ratio of Na2SiO3/NaOH was 2 and fly ash to aggregate of 1: 3. The experiments were conducted with variation of the sodium hidroxida concentration of (10-16 M) liquid to solid (L/S) 0.1- 0.7 ratio, curing temperature 30-100 °C and curing time (7-28 day). The main evaluation techniques in this experimental were Compressive strength, X-ray diffraction (XRD),and Scaning Electron Microscope (SEM). The result showed that the compressive strength of Geopolymer Paving block has increased with an increasing of concentration, liquid to solid ratio, curing temperature and curing time.

Image quality enhancement in low-light-level ghost imaging using modified compressive sensing method

NASA Astrophysics Data System (ADS)

Shi, Xiaohui; Huang, Xianwei; Nan, Suqin; Li, Hengxing; Bai, Yanfeng; Fu, Xiquan

2018-04-01

Detector noise has a significantly negative impact on ghost imaging at low light levels, especially for existing recovery algorithm. Based on the characteristics of the additive detector noise, a method named modified compressive sensing ghost imaging is proposed to reduce the background imposed by the randomly distributed detector noise at signal path. Experimental results show that, with an appropriate choice of threshold value, modified compressive sensing ghost imaging algorithm can dramatically enhance the contrast-to-noise ratio of the object reconstruction significantly compared with traditional ghost imaging and compressive sensing ghost imaging methods. The relationship between the contrast-to-noise ratio of the reconstruction image and the intensity ratio (namely, the average signal intensity to average noise intensity ratio) for the three reconstruction algorithms are also discussed. This noise suppression imaging technique will have great applications in remote-sensing and security areas.

Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

NASA Astrophysics Data System (ADS)

Opara, Hyginus E.; Eziefula, Uchechi G.; Eziefula, Bennett I.

2018-03-01

This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghosh, B.B.

The object of the study reported in this paper was to investigate the possibility of using the blend of kerosene with petrol in a gasoline engines, without much losses in performance. The authors carried out experiments on a four-stroke cycle Briggs and Stratton S. I. Engine using five blends of kerosene with petrol at a compression ratios 5.3 and 7.47 to 1 with and without surge chambers, at a constant engine speed of 1500 rev/min with the following conclusions: 1. At part-load and the lower compression ratio the brake thermal efficiency is improved with percentage increase of kerosene but atmore » the higher compression ratio it is improved only upto 50% kerosene blend with petrol. 2. The knock-free maximum bhp is reduced with (a) the percentage increase of kerosene, (b) the increase of compression ratio. 3. Use of a surge chamber increase the knock-free maximum bhp, and reduces the brake thermal efficiency.« less

An Open-Label Exploratory Study with Memantine: Correlation between Proton Magnetic Resonance Spectroscopy and Cognition in Patients with Mild to Moderate Alzheimer's Disease

PubMed Central

Gordon, Marc L.; Kingsley, Peter B.; Goldberg, Terry E.; Koppel, Jeremy; Christen, Erica; Keehlisen, Lynda; Kohn, Nina; Davies, Peter

2012-01-01

Aim To characterize progression of Alzheimer's disease (AD) using proton magnetic resonance spectroscopy (1H MRS). Methods Eleven subjects with mild to moderate AD underwent neurocognitive testing and single-voxel 1H MRS from the precuneus and posterior cingulate region at baseline, after 24 weeks of monotherapy with a cholinesterase inhibitor, and after another 24 weeks of combination therapy with open-label memantine and a cholinesterase inhibitor. Baseline metabolites [N-acetylaspartate (NAA), myo-inositol (mI), choline (Cho), and creatine (Cr)] and their ratios in AD subjects were compared with those of an age-matched control group of 28 cognitively normal subjects. Results AD subjects had significantly higher mI/Cr and lower NAA, NAA/Cr, NAA/Cho, and NAA/mI. Baseline Alzheimer's Disease Cooperative Study Activities of Daily Living (ADCS-ADL) scores significantly correlated with NAA/Cr, mI/Cr, and NAA/mI. There was an increase in mI and a decrease in NAA/mI, but no significant change in other metabolites or ratios, or neurocognitive measures, when memantine was added to a cholinesterase inhibitor. Conclusion Metabolite ratios significantly differed between AD and control subjects. Baseline metabolite ratios correlated with function (ADCS-ADL). There was an increase in mI and a decrease in NAA/mI, but no changes in other metabolites, ratios, or cognitive measures, when memantine was added to a cholinesterase inhibitor. PMID:22962555

Coupled double-distribution-function lattice Boltzmann method for the compressible Navier-Stokes equations.

PubMed

Li, Q; He, Y L; Wang, Y; Tao, W Q

2007-11-01

A coupled double-distribution-function lattice Boltzmann method is developed for the compressible Navier-Stokes equations. Different from existing thermal lattice Boltzmann methods, this method can recover the compressible Navier-Stokes equations with a flexible specific-heat ratio and Prandtl number. In the method, a density distribution function based on a multispeed lattice is used to recover the compressible continuity and momentum equations, while the compressible energy equation is recovered by an energy distribution function. The energy distribution function is then coupled to the density distribution function via the thermal equation of state. In order to obtain an adjustable specific-heat ratio, a constant related to the specific-heat ratio is introduced into the equilibrium energy distribution function. Two different coupled double-distribution-function lattice Boltzmann models are also proposed in the paper. Numerical simulations are performed for the Riemann problem, the double-Mach-reflection problem, and the Couette flow with a range of specific-heat ratios and Prandtl numbers. The numerical results are found to be in excellent agreement with analytical and/or other solutions.

Monitoring creatine and phosphocreatine by (13)C MR spectroscopic imaging during and after (13)C4 creatine loading: a feasibility study.

PubMed

Janssen, Barbara H; Lassche, Saskia; Hopman, Maria T; Wevers, Ron A; van Engelen, Baziel G M; Heerschap, Arend

2016-08-01

Creatine (Cr) supplementation to enhance muscle performance shows variable responses among individuals and different muscles. Direct monitoring of the supplied Cr in muscles would address these differences. In this feasibility study, we introduce in vivo 3D (13)C MR spectroscopic imaging (MRSI) of the leg with oral ingestion of (13)C4-creatine to observe simultaneously Cr and phosphocreatine (PCr) for assessing Cr uptake, turnover, and the ratio PCr over total Cr (TCr) in individual muscles. (13)C MRSI was performed of five muscles in the posterior thigh in seven subjects (two males and two females of ~20 years, one 82-year-old male, and two neuromuscular patients) with a (1)H/(13)C coil in a 3T MR system before, during and after intake of 15 % (13)C4-enriched Cr. Subjects ingested 20 g Cr/day for 4 days in four 5 g doses at equal time intervals. The PCr/TCr did not vary significantly during supplementation and was similar for all subjects and investigated muscles (average 0.71 ± 0.07), except for the adductor magnus (0.64 ± 0.03). The average Cr turnover rate, assessed in male muscles, was 2.1 ± 0.7 %/day. The linear uptake rates of Cr were variable between muscles, although not significantly different. This assessment was possible in all investigated muscles of young male volunteers, but less so in muscles of the other subjects due to lower signal-to-noise ratio. Improvements for future studies are discussed. In vivo (13)C MRSI after (13)C-Cr ingestion is demonstrated for longitudinal studies of Cr uptake, turnover, and PCr/TCr ratios of individual muscles in one exam.

Radiographic Risk Factors for Contralateral Rupture in Dogs with Unilateral Cranial Cruciate Ligament Rupture

PubMed Central

Chuang, Connie; Ramaker, Megan A.; Kaur, Sirjaut; Csomos, Rebecca A.; Kroner, Kevin T.; Bleedorn, Jason A.; Schaefer, Susan L.; Muir, Peter

2014-01-01

Background Complete cranial cruciate ligament rupture (CR) is a common cause of pelvic limb lameness in dogs. Dogs with unilateral CR often develop contralateral CR over time. Although radiographic signs of contralateral stifle joint osteoarthritis (OA) influence risk of subsequent contralateral CR, this risk has not been studied in detail. Methodology/Principal Findings We conducted a retrospective longitudinal cohort study of client-owned dogs with unilateral CR to determine how severity of radiographic stifle synovial effusion and osteophytosis influence risk of contralateral CR over time. Detailed survival analysis was performed for a cohort of 85 dogs after case filtering of an initial sample population of 513 dogs. This population was stratified based on radiographic severity of synovial effusion (graded on a scale of 0, 1, and 2) and severity of osteophytosis (graded on a scale of 0, 1, 2, and 3) of both index and contralateral stifle joints using a reproducible scoring method. Severity of osteophytosis in the index and contralateral stifles was significantly correlated. Rupture of the contralateral cranial cruciate ligament was significantly influenced by radiographic OA in both the index and contralateral stifles at diagnosis. Odds ratio for development of contralateral CR in dogs with severe contralateral radiographic stifle effusion was 13.4 at one year after diagnosis and 11.4 at two years. Odds ratio for development of contralateral CR in dogs with severe contralateral osteophytosis was 9.9 at one year after diagnosis. These odds ratios were associated with decreased time to contralateral CR. Breed, age, body weight, gender, and tibial plateau angle did not significantly influence time to contralateral CR. Conclusion Subsequent contralateral CR is significantly influenced by severity of radiographic stifle effusion and osteophytosis in the contralateral stifle, suggesting that synovitis and arthritic joint degeneration are significant factors in the disease mechanism underlying the arthropathy. PMID:25254499

Increased N-Acetylaspartate/creatine ratio in the medial prefrontal cortex among unmedicated obsessive-compulsive disorder patients.

PubMed

Fan, Qing; Tan, Ling; You, Chao; Wang, Jijun; Ross, Colin A; Wang, Xuemei; Zhang, Tianhong; Li, Jianqi; Chen, Kemin; Xiao, Zeping

2010-10-01

Changes in the fronto-striato-thalamo-cortical-circuit loop have been suggested in the pathogenesis of obsessive-compulsive disorder (OCD), and have been studied using (1)H magnetic resonance spectroscopy ((1)H MRS) with interesting findings. However, whether neural metabolites are abnormal in the medial prefrontal cortex in patients with OCD is unknown. The purpose of the present study was to investigate neural metabolites in this brain region in a sample of patients with OCD. Subjects were 21 unmedicated OCD patients, including 10 who were drug-naïve, and 19 healthy controls. Single-voxel (1)H MRS was used to study the medial prefrontal cortex for each subject. Levels of N-acetylaspartate (NAA), choline-containing compounds and myoinositol were measured in terms of their ratios with creatine (Cr). The NAA/Cr ratio was significantly higher among OCD patients than among healthy controls (F = 4.76, P = 0.037). However, it did not correlate with patients' symptoms or with their illness durations. The NAA/Cr ratio also did not differ between drug-naïve and previously medicated patients. No significant group differences were found between OCD patients and normal controls for the choline-containing compounds/Cr or myoinositol/Cr ratios. In addition, a significant correlation between the NAA/Cr ratio and trait anxiety scores on the State-Trait Anxiety Inventory was found among the controls (r = 0.639, P = 0.010). The N-Acetylaspartate level relative to creatine in the medial prefrontal cortex was increased among unmedicated OCD patients. This cannot be attributed to the effect of medications. The possible significance of this finding in the pathophysiology of OCD is discussed. © 2010 Shanghai Mental Health Center, Shanghai Jiao Tong University School of Medicine. Psychiatry and Clinical Neurosciences © 2010 Japanese Society of Psychiatry and Neurology.

X-Ray Absorption Near Edge Structure And Extended X-Ray Absorption Fine Structure Analysis of Standards And Biological Samples Containing Mixed Oxidation States of Chromium(III) And Chromium(VI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parsons, J.G.; Dokken, K.; Peralta-Videa, J.R.

For the first time a method has been developed for the extended X-ray absorption fine structure (EXAFS) data analyses of biological samples containing multiple oxidation states of chromium. In this study, the first shell coordination and interatomic distances based on the data analysis of known standards of potassium chromate (Cr(VI)) and chromium nitrate hexahydrate (Cr(III)) were investigated. The standards examined were mixtures of the following molar ratios of Cr(VI):Cr(III), 0:1, 0.25:0.75, 0.5:0.5, 0.75:0.25, and 1:0. It was determined from the calibration data that the fitting error associated with linear combination X-ray absorption near edge structure (LC-XANES) fittings was approximately {+-}10%more » of the total fitting. The peak height of the Cr(VI) pre-edge feature after normalization of the X-ray absorption (XAS) spectra was used to prepare a calibration curve. The EXAFS fittings of the standards were also investigated and fittings to lechuguilla biomass samples laden with different ratios of Cr(III) and Cr(VI) were performed as well. An excellent agreement between the XANES data and the data presented in the EXAFS spectra was observed. The EXFAS data also presented mean coordination numbers directly related to the ratios of the different chromium oxidation states in the sample. The chromium oxygen interactions had two different bond lengths at approximately 1.68 and 1.98 {angstrom} for the Cr(VI) and Cr(III) in the sample, respectively.« less

Pilot scale treatment of chromite ore processing residue using sodium sulfide in single reduction and coupled reduction/stabilization processes.

PubMed

Velasco, Antonio; Ramírez, Martha; Hernández, Sergio; Schmidt, Winfried; Revah, Sergio

2012-03-15

Single Cr(VI) reduction and coupled reduction/stabilization (R/S) processes were evaluated at pilot scale to determine their effectiveness to treat chromite ore processing residue (COPR). Sodium sulfide was used as the reducing agent and cement, gypsum and lime were tested as the stabilizing agents. The pilot experiments were performed in a helical ribbon blender mixer with batches of 250 kg of COPR and mixing time up to 30 min. Na2S/Cr(VI) mass ratios of 4.6, 5.7 and 6.8 were evaluated in the single reduction process to treat COPR with Cr(VI) concentration of ≈4.2 g/kg. The R/S process was tested with a Na2S/Cr(VI) mass ratio of 5.7 and including stabilizing agents not exceeding 5% (w/w(COPR)), to treat COPR with a Cr(VI) content of ≈5.1g/kg. The single reduction process with a ratio of 6.8, reached Cr(VI) reduction efficiencies up to 97.6% in the first days, however these values decreased to around 93% after 380 days of storage. At this point the total Cr level was around 12.5 mg/L. Cr(VI) removal efficiencies exceeding 96.5% were reached and maintained during 380 days when the coupled R/S process was evaluated. Total Cr levels lower than 5 mg/l were attained at the initials days in all R/S batch tested, however after 380 days, concentrations below the regulatory limit were only found with gypsum (2%) as single agent and with a blend of cement (4%) and lime (1%). These results indicated that the coupled R/S process is an excellent alternative to stabilize COPR. Copyright © 2011 Elsevier B.V. All rights reserved.

High-speed and high-ratio referential genome compression.

PubMed

Liu, Yuansheng; Peng, Hui; Wong, Limsoon; Li, Jinyan

2017-11-01

The rapidly increasing number of genomes generated by high-throughput sequencing platforms and assembly algorithms is accompanied by problems in data storage, compression and communication. Traditional compression algorithms are unable to meet the demand of high compression ratio due to the intrinsic challenging features of DNA sequences such as small alphabet size, frequent repeats and palindromes. Reference-based lossless compression, by which only the differences between two similar genomes are stored, is a promising approach with high compression ratio. We present a high-performance referential genome compression algorithm named HiRGC. It is based on a 2-bit encoding scheme and an advanced greedy-matching search on a hash table. We compare the performance of HiRGC with four state-of-the-art compression methods on a benchmark dataset of eight human genomes. HiRGC takes <30 min to compress about 21 gigabytes of each set of the seven target genomes into 96-260 megabytes, achieving compression ratios of 217 to 82 times. This performance is at least 1.9 times better than the best competing algorithm on its best case. Our compression speed is also at least 2.9 times faster. HiRGC is stable and robust to deal with different reference genomes. In contrast, the competing methods' performance varies widely on different reference genomes. More experiments on 100 human genomes from the 1000 Genome Project and on genomes of several other species again demonstrate that HiRGC's performance is consistently excellent. The C ++ and Java source codes of our algorithm are freely available for academic and non-commercial use. They can be downloaded from https://github.com/yuansliu/HiRGC. jinyan.li@uts.edu.au. Supplementary data are available at Bioinformatics online. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

A Synthetic Calcite Standard for Determination of Relative Mn/Cr Sensitivity Factor

NASA Astrophysics Data System (ADS)

Fujiya, W.; Ichimura, K.; Takahata, N.; Sugiura, N.; Sano, Y.

2009-12-01

Primitive chondrites which suffered from aqueous alteration often contain carbonates such as calcites, dolomites and breunnerites. 53Mn-53Cr decay system (half-life: 3.7 Myr) is applicable to dating their precipitation and many authors have measured their Mn-Cr ages using the SIMS. However, the relative Mn/Cr sensitivity factor: RSF (measured Mn+/Cr+ ratio divided by the true ratio) is not well established due to the absence of suitable standards, therefore the ages have systematic uncertainties. We prepared a synthetic Mn and Cr bearing calcite to evaluate the Mn/Cr RSF. Here we report the technical details of preparation for the standard and its Mn/Cr RSF. We also measured the Mn/Cr RSF of San Carlos olivine which is often assumed to be the same as that of a carbonate, and compared it with that of our synthetic calcite. The Cr-bearing calcite was produced in a N2 filled closed system by the reaction Ca2+ + CO32- = CaCO3 in an aqueous solution. The reaction proceeded by continuous addition of ammonium carbonate vapor to the solution. The crystal size of the calcite was ~300 μm. A small amount of hydrazine was added to the solution in order to keep chromous ion from oxidation. Mn and Cr concentrations in the calcite grains were determined by the SEM-EDS. A weak, defocused beam was used due to prevent electron beam damage. In a spherical grain, radial zoning of Mn and Cr concentrations occur and they decrease towards the periphery. At the center of the grains, Mn and Cr concentrations are ~0.5 atomic % and the values of the Mn/Cr ratios are relatively constant. The Mn/Cr RSF was determined with the CAMECA NanoSIMS 50 at Ocean Research Institute of Univ. of Tokyo. A primary O- beam of ~1 nA and 5 μm diameter was used. 43Ca+, 52Cr+, 53Cr+ and 55Mn+ ions were analyzed in a combined peak-jumping/multi-detection mode. The total measurement time was typically ~20 minutes. The measurements were started after presputtering of 15 minutes. The mass resolution power was ~3500, sufficient to resolve all relevant isobaric interferences. Several points near the center of calcite grains with constant Mn and Cr concentrations were measured. As for San Carlos olivine, a primary beam was rastered over 20 x 20 μm2 areas. Signals of all ions decreased with time during the measurements. The 55Mn/52Cr RSF also decreased with time. Initially it was ~0.7-0.8, and approached to a nearly constant value of ~0.5-0.6 after ~20 minutes. 53Cr+/52Cr+ isotopic ratio was 0.1105 ± 0.0002 (1σ), not dependent on time and space. This value corresponds to ~-26 permil fractionation from the reference value. On the other hand, the RSF of San Carlos olivine was found to be ~0.9, consistent with previous studies. The RSF of our calcite is significantly lower than the values used in previous studies and the RSF of San Carlos olivine measured in this study. This implies that Mn-Cr ages for carbonates obtained in previous studies may have systematic biases (~3 Myr).

CoGI: Towards Compressing Genomes as an Image.

PubMed

Xie, Xiaojing; Zhou, Shuigeng; Guan, Jihong

2015-01-01

Genomic science is now facing an explosive increase of data thanks to the fast development of sequencing technology. This situation poses serious challenges to genomic data storage and transferring. It is desirable to compress data to reduce storage and transferring cost, and thus to boost data distribution and utilization efficiency. Up to now, a number of algorithms / tools have been developed for compressing genomic sequences. Unlike the existing algorithms, most of which treat genomes as one-dimensional text strings and compress them based on dictionaries or probability models, this paper proposes a novel approach called CoGI (the abbreviation of Compressing Genomes as an Image) for genome compression, which transforms the genomic sequences to a two-dimensional binary image (or bitmap), then applies a rectangular partition coding algorithm to compress the binary image. CoGI can be used as either a reference-based compressor or a reference-free compressor. For the former, we develop two entropy-based algorithms to select a proper reference genome. Performance evaluation is conducted on various genomes. Experimental results show that the reference-based CoGI significantly outperforms two state-of-the-art reference-based genome compressors GReEn and RLZ-opt in both compression ratio and compression efficiency. It also achieves comparable compression ratio but two orders of magnitude higher compression efficiency in comparison with XM--one state-of-the-art reference-free genome compressor. Furthermore, our approach performs much better than Gzip--a general-purpose and widely-used compressor, in both compression speed and compression ratio. So, CoGI can serve as an effective and practical genome compressor. The source code and other related documents of CoGI are available at: http://admis.fudan.edu.cn/projects/cogi.htm.

Optimization of on-line hydrogen stable isotope ratio measurements of halogen- and sulfur-bearing organic compounds using elemental analyzer–chromium/high-temperature conversion isotope ratio mass spectrometry (EA-Cr/HTC-IRMS)

USGS Publications Warehouse

Gehre, Matthias; Renpenning, Julian; Geilmann, Heike; Qi, Haiping; Coplen, Tyler B.; Kümmel, Steffen; Ivdra, Natalija; Brand, Willi A.; Schimmelmann, Arndt

2017-01-01

Conclusions: The optimized EA-Cr/HTC reactor design can be implemented in existing analytical equipment using commercially available material and is universally applicable for both heteroelement-bearing and heteroelement-free organic-compound classes. The sensitivity and simplicity of the on-line EA-Cr/HTC-IRMS technique provide a much needed tool for routine hydrogen-isotope source tracing of organic contaminants in the environment. Copyright © 2016 John Wiley & Sons, Ltd.

The Preparation of Porous Sol-Gel Silica with Metal Organic Framework MIL-101(Cr) by Microwave-Assisted Hydrothermal Method for Adsorption Chillers.

PubMed

Uma, Kasimayan; Pan, Guan-Ting; Yang, Thomas C-K

2017-06-02

Abst r act: Metal organic framework (MOF) of MIL-101(Cr)-Silica (SiO₂) composites with highly mesoporous and uniform dispersions were synthesized by a microwave-assisted hydrothermal method followed by the sol-gel technique. Water vapor adsorption experiments were conducted on the MIL-101(Cr)-SiO₂ composites for industrial adsorption chiller applications. The effects of MIL-101(Cr)-SiO₂ mixing ratios (ranging from 0% to 52%), the surface area and amount of Lewis and Brønsted sites were comprehensively determined through water vapor adsorption experiments and the adsorption mechanism is also explained. The BET and Langmuir results indicate that the adsorption isotherms associated with the various MIL-101(Cr)-SiO₂ ratios demonstrated Type I and IV adsorption behavior, due to the mesoporous structure of the MIL-101(Cr)-SiO₂. It was observed that the increase in the amount of Lewis and Brønsted sites on the MIL-101(Cr)-SiO₂ composites significantly improves the water vapor adsorption efficiency, for greater stability during the water vapor adsorption experiments.

The effect of cosmic-ray acceleration on supernova blast wave dynamics

NASA Astrophysics Data System (ADS)

Pais, M.; Pfrommer, C.; Ehlert, K.; Pakmor, R.

2018-05-01

Non-relativistic shocks accelerate ions to highly relativistic energies provided that the orientation of the magnetic field is closely aligned with the shock normal (quasi-parallel shock configuration). In contrast, quasi-perpendicular shocks do not efficiently accelerate ions. We model this obliquity-dependent acceleration process in a spherically expanding blast wave setup with the moving-mesh code AREPO for different magnetic field morphologies, ranging from homogeneous to turbulent configurations. A Sedov-Taylor explosion in a homogeneous magnetic field generates an oblate ellipsoidal shock surface due to the slower propagating blast wave in the direction of the magnetic field. This is because of the efficient cosmic ray (CR) production in the quasi-parallel polar cap regions, which softens the equation of state and increases the compressibility of the post-shock gas. We find that the solution remains self-similar because the ellipticity of the propagating blast wave stays constant in time. This enables us to derive an effective ratio of specific heats for a composite of thermal gas and CRs as a function of the maximum acceleration efficiency. We finally discuss the behavior of supernova remnants expanding into a turbulent magnetic field with varying coherence lengths. For a maximum CR acceleration efficiency of about 15 per cent at quasi-parallel shocks (as suggested by kinetic plasma simulations), we find an average efficiency of about 5 per cent, independent of the assumed magnetic coherence length.

Observer detection of image degradation caused by irreversible data compression processes

NASA Astrophysics Data System (ADS)

Chen, Ji; Flynn, Michael J.; Gross, Barry; Spizarny, David

1991-05-01

Irreversible data compression methods have been proposed to reduce the data storage and communication requirements of digital imaging systems. In general, the error produced by compression increases as an algorithm''s compression ratio is increased. We have studied the relationship between compression ratios and the detection of induced error using radiologic observers. The nature of the errors was characterized by calculating the power spectrum of the difference image. In contrast with studies designed to test whether detected errors alter diagnostic decisions, this study was designed to test whether observers could detect the induced error. A paired-film observer study was designed to test whether induced errors were detected. The study was conducted with chest radiographs selected and ranked for subtle evidence of interstitial disease, pulmonary nodules, or pneumothoraces. Images were digitized at 86 microns (4K X 5K) and 2K X 2K regions were extracted. A full-frame discrete cosine transform method was used to compress images at ratios varying between 6:1 and 60:1. The decompressed images were reprinted next to the original images in a randomized order with a laser film printer. The use of a film digitizer and a film printer which can reproduce all of the contrast and detail in the original radiograph makes the results of this study insensitive to instrument performance and primarily dependent on radiographic image quality. The results of this study define conditions for which errors associated with irreversible compression cannot be detected by radiologic observers. The results indicate that an observer can detect the errors introduced by this compression algorithm for compression ratios of 10:1 (1.2 bits/pixel) or higher.

[Treatment of wastewater containing Cr(VI) by LDH synthesizing in situ].

PubMed

Chen, Tian-hu; Feng, You-liang; Xu, Hui-fang; Peng, Shu-chuan; Huang, Chuan-hui; Tang, Shu-pei

2004-03-01

The objective of this work was to investigate the efficiency and factors impacting of removal Cr(VI) from wastewater by layer double hydroxide synthesizing in situ. Principle of the method may be described as follow: Mg2+ and Al3+ hydrolysis and forms Mg/Al-LDH by adding Mg2+, Al3+ and NaOH into wastewater containing Cr(VI), Cr(VI) anions are selectively intercalated into interlayer of LDH to balance positive structural charge. While Mg2+ and Al3+ co-precipitates and forms LDH, the Cr(VI) in wastewater is removal by settle of LDH synthesizing in situ, which are confirmed by analysis of X-ray diffraction on settle and chemical analysis on aqueous. The results indicate that factors of impacting on efficiency of removal Cr(VI) include in amount of adding Mg2+ and Al3+, Mg/Al ratio, pH and concentration of Cr(VI) in wastewater. The maximal removal efficiency of Cr(VI) can be reached when pH values are between 8.5 and 9, and Mg/Al ratios are between 1:1 and 2:1, meanwhile, Mg and Al added can be taken good use of. This technology has present extraordinary efficiency of wastewater treatment.

A new approach of objective quality evaluation on JPEG2000 lossy-compressed lung cancer CT images

NASA Astrophysics Data System (ADS)

Cai, Weihua; Tan, Yongqiang; Zhang, Jianguo

2007-03-01

Image compression has been used to increase the communication efficiency and storage capacity. JPEG 2000 compression, based on the wavelet transformation, has its advantages comparing to other compression methods, such as ROI coding, error resilience, adaptive binary arithmetic coding and embedded bit-stream. However it is still difficult to find an objective method to evaluate the image quality of lossy-compressed medical images so far. In this paper, we present an approach to evaluate the image quality by using a computer aided diagnosis (CAD) system. We selected 77 cases of CT images, bearing benign and malignant lung nodules with confirmed pathology, from our clinical Picture Archiving and Communication System (PACS). We have developed a prototype of CAD system to classify these images into benign ones and malignant ones, the performance of which was evaluated by the receiver operator characteristics (ROC) curves. We first used JPEG 2000 to compress these cases of images with different compression ratio from lossless to lossy, and used the CAD system to classify the cases with different compressed ratio, then compared the ROC curves from the CAD classification results. Support vector machine (SVM) and neural networks (NN) were used to classify the malignancy of input nodules. In each approach, we found that the area under ROC (AUC) decreases with the increment of compression ratio with small fluctuations.

Origin of texture development in orthorhombic uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zecevic, Miroslav; Knezevic, Marko; Beyerlein, Irene Jane

We study texture evolution of alpha-uranium (α-U) during plane strain compression and uniaxial compression to high strains at different temperatures. We combine a multiscale polycrystal constitutive model and detailed analysis of texture data to uncover the slip and twinning modes responsible for the formation of individual texture components. The analysis indicates that during plane strain compression, floor slip (001)[100] results in the formation of two pronounced {001}{001} texture peaks tilted 10–15° away from the normal toward the rolling direction. During both high-temperature (573 K) through-thickness compression and plane strain compression, the active slip modes are floor slip (001)[100] and chimneymore » slip 1/2{110} <11¯0> with slightly different ratios. {130} <31¯0> deformation twinning is profuse during rolling and in-plane compression and decreases with increasing temperature, but is not as active for through-thickness compression. Lastly, we comment on some similarities between rolling textures of α-U, which has a c/a ratio of 1.734, and those that develop in hexagonal close packed metals with similarly high c/a ratios like Zn (1.856) and Cd (1.885) and are dominated by basal slip.« less

Origin of texture development in orthorhombic uranium

DOE PAGES

Zecevic, Miroslav; Knezevic, Marko; Beyerlein, Irene Jane; ...

2016-04-09

We study texture evolution of alpha-uranium (α-U) during plane strain compression and uniaxial compression to high strains at different temperatures. We combine a multiscale polycrystal constitutive model and detailed analysis of texture data to uncover the slip and twinning modes responsible for the formation of individual texture components. The analysis indicates that during plane strain compression, floor slip (001)[100] results in the formation of two pronounced {001}{001} texture peaks tilted 10–15° away from the normal toward the rolling direction. During both high-temperature (573 K) through-thickness compression and plane strain compression, the active slip modes are floor slip (001)[100] and chimneymore » slip 1/2{110} <11¯0> with slightly different ratios. {130} <31¯0> deformation twinning is profuse during rolling and in-plane compression and decreases with increasing temperature, but is not as active for through-thickness compression. Lastly, we comment on some similarities between rolling textures of α-U, which has a c/a ratio of 1.734, and those that develop in hexagonal close packed metals with similarly high c/a ratios like Zn (1.856) and Cd (1.885) and are dominated by basal slip.« less

Supernova Driving. II. Compressive Ratio in Molecular-cloud Turbulence

NASA Astrophysics Data System (ADS)

Pan, Liubin; Padoan, Paolo; Haugbølle, Troels; Nordlund, Åke

2016-07-01

The compressibility of molecular cloud (MC) turbulence plays a crucial role in star formation models, because it controls the amplitude and distribution of density fluctuations. The relation between the compressive ratio (the ratio of powers in compressive and solenoidal motions) and the statistics of turbulence has been previously studied systematically only in idealized simulations with random external forces. In this work, we analyze a simulation of large-scale turbulence (250 pc) driven by supernova (SN) explosions that has been shown to yield realistic MC properties. We demonstrate that SN driving results in MC turbulence with a broad lognormal distribution of the compressive ratio, with a mean value ≈0.3, lower than the equilibrium value of ≈0.5 found in the inertial range of isothermal simulations with random solenoidal driving. We also find that the compressibility of the turbulence is not noticeably affected by gravity, nor are the mean cloud radial (expansion or contraction) and solid-body rotation velocities. Furthermore, the clouds follow a general relation between the rms density and the rms Mach number similar to that of supersonic isothermal turbulence, though with a large scatter, and their average gas density probability density function is described well by a lognormal distribution, with the addition of a high-density power-law tail when self-gravity is included.

Effect of angle-ply orientation on compression strength of composite laminates

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeTeresa, S J; Hoppel, C P

1999-03-01

An experimental program was initiated to investigate the effect of angle-ply orientations on the compressive strength (X{sub 1C}) of 0{degree} plies in fiber reinforced composite laminates. Graphite fiber-reinforced epoxy test coupons with the generic architecture [0{sub 2}/{+-}{theta}] (where {theta} varied between 0{degree} and 90{degree}) and for the quasi-isotropic architecture were evaluated. The effective compressive strength of the 0{degree} plies varied considerably. The results were related to the Poisson's ratios of the laminates with high Poisson's ratios leading to high transverse tensile strains in the test coupons and lower than expected strengths. Specimens with the [O{sub 2}/{+-}30] architecture had both themore » highest Poisson's ratio and the lowest calculated ply-level compression strength for the 0{degree} plies. This work has implications in the selection of composite failure criterion for compression performance, design of test coupons for acceptance testing, and the selection of laminate architectures for optimum combinations of compressive and shear behavior. Two commonly used composite failure criteria, the maximum stress and the Tsai-Wu, predict significantly different laminate strengths depending on the Poisson's ratio of the laminate. This implies that the biaxial stress state in the laminate needs to be carefully considered before backing out unidirectional properties.« less

Urinary Uric Acid/Creatinine Ratio - A Marker For Perinatal Asphyxia

PubMed Central

Patel, Kinjal Prahaladbhai; Makadia, Mayur Goradhanbhai; Patel, Vishwal Indravardan; Nilayangode, Haridas Neelakandan

2017-01-01

Background Perinatal hypoxia is one of the leading causes of perinatal mortality in developing countries. Both apgar score and arterial blood pH predict the neonatal mortality in asphyxia. Apgar score alone does not predict neurologic outcome and as it is influenced by various factors. This study was conducted to evaluate the utility and sensitivity of urinary uric acid to creatinine ratio (UA/Cr ratio) in asphyxia diagnosis, compared to invasive Arterial Blood Gas (ABG) analysis. Aim To assess the urinary uric acid/creatinine ratio as an additional marker for perinatal asphyxia compared with ABG analysis in apgar score monitoring. Materials and Methods The present case control study was conducted at a teaching hospital in Central Gujarat. Data of 40 healthy newborns and 40 asphyxiated newborns were collected. In absence of regional estimates, a sample of size 39 was required to attain a power of 80% at 5% alpha (type I error) considering a moderate effect size of 0.65. (UA/Cr) ratio was measured from the spot urine sample collected during 24-72 hours of birth. Statistical analysis was performed by Independent t-test, Pearson’s correlation coefficient (r) and Receiver Operating Characteristic (ROC) plots. Results The mean (UA/Cr ratio) (2.75±0.18 vs 1.78±0.23) is significantly higher in asphyxiated group than in the control group (p<0.0001). Urinary UA/Cr ratio had negative correlation with blood pH (r= -0.27, p=0.18), which was not significant (p>0.05). Urinary UA/Cr ratio with criterion of >2.3 had 100% sensitivity, 100% specificity with AUC of 1 (p<0.0001) had a better predictive value. Conclusions Apgar score is usually reduced in neonates with congenital anomalies and premature neonates. Hence, it is preferable that the clinical diagnosis of asphyxia by apgar scores be supported by other investigations so that early decision can be taken about the level of care the baby needs. pH, lactates and base deficits change with establishment of respiration following resuscitation. However, pH, lactate, base deficit estimations are invasive and need rapid estimations. Non-invasive urinary UA/Cr ratio may be an answer to these issues as it easy, economical and equally efficient. PMID:28274014

Component optimization of dairy manure vermicompost, straw, and peat in seedling compressed substrates using simplex-centroid design.

PubMed

Yang, Longyuan; Cao, Hongliang; Yuan, Qiaoxia; Luoa, Shuai; Liu, Zhigang

2018-03-01

Vermicomposting is a promising method to disposal dairy manures, and the dairy manure vermicompost (DMV) to replace expensive peat is of high value in the application of seedling compressed substrates. In this research, three main components: DMV, straw, and peat, are conducted in the compressed substrates, and the effect of individual components and the corresponding optimal ratio for the seedling production are significant. To address these issues, the simplex-centroid experimental mixture design is employed, and the cucumber seedling experiment is conducted to evaluate the compressed substrates. Results demonstrated that the mechanical strength and physicochemical properties of compressed substrates for cucumber seedling can be well satisfied with suitable mixture ratio of the components. Moreover, DMV, straw, and peat) could be determined at 0.5917:0.1608:0.2475 when the weight coefficients of the three parameters (shoot length, root dry weight, and aboveground dry weight) were 1:1:1. For different purpose, the optimum ratio can be little changed on the basis of different weight coefficients. Compressed substrate is lump and has certain mechanical strength, produced by application of mechanical pressure to the seedling substrates. It will not harm seedlings when bedding out the seedlings, since the compressed substrate and seedling are bedded out together. However, there is no one using the vermicompost and agricultural waste components of compressed substrate for vegetable seedling production before. Thus, it is important to understand the effect of individual components to seedling production, and to determine the optimal ratio of components.

Toward an image compression algorithm for the high-resolution electronic still camera

NASA Technical Reports Server (NTRS)

Nerheim, Rosalee

1989-01-01

Taking pictures with a camera that uses a digital recording medium instead of film has the advantage of recording and transmitting images without the use of a darkroom or a courier. However, high-resolution images contain an enormous amount of information and strain data-storage systems. Image compression will allow multiple images to be stored in the High-Resolution Electronic Still Camera. The camera is under development at Johnson Space Center. Fidelity of the reproduced image and compression speed are of tantamount importance. Lossless compression algorithms are fast and faithfully reproduce the image, but their compression ratios will be unacceptably low due to noise in the front end of the camera. Future efforts will include exploring methods that will reduce the noise in the image and increase the compression ratio.

Strengthening of Fe3Al Aluminides by One or Two Solute Elements

NASA Astrophysics Data System (ADS)

Kratochvíl, Petr; Daniš, Stanislav; Minárik, Peter; Pešička, Josef; Král, Robert

2017-09-01

The compressive yield stress of Fe-26Al with additives Ti (0.5 to 4 at. pct), Cr (0.5 to 8 at. pct), Mo (0.5 to 4 at. pct), and V (0.5 to 8 at. pct) at 1073 K (800 °C) has been determined. The effect of the concentration of diverse solutes on the yield stress at 1073 K (800 °C) was compared, and the additivity of the effects of solutes was tested. The effects in iron aluminides with two solutes (V and Ti, Ti and Cr, V and Cr) are compared with those of a single solute V, Ti, and Cr. It is found that the additivity of yield stress increments is valid only for lower solute concentrations. When the amount of the solute atoms increases, the yield stress increment is substantially higher than the sum of the yield stress increments of single solutes. This behavior is related to the high-temperature order in iron aluminides.

Anomalous Buckling Characteristics of Laminated Metal-Matrix Composite Plates with Central Square Holes

NASA Technical Reports Server (NTRS)

Ko, William L.

1998-01-01

Compressive buckling analysis was performed on metal-matrix composite (MMC) plates with central square holes. The MMC plates have varying aspect ratios and hole sizes and are supported under different boundary conditions. The finite-element structural analysis method was used to study the effects of plate boundary conditions, plate aspect ratio, hole size, and the composite stacking sequence on the compressive buckling strengths of the perforated MMC plates. Studies show that by increasing the hole sizes, compressive buckling strengths of the perforated MMC plates could be considerably increased under certain boundary conditions and aspect ratios ("anomalous" buckling behavior); and that the plate buckling mode could be symmetrical or antisymmetrical, depending on the plate boundary conditions, aspect ratio, and the hole size. For same-sized plates with same-sized holes, the compressive buckling strengths of the perforated MMC plates with [90/0/0/90]2 lamination could be as much as 10 percent higher or lower than those of the [45/- 45/- 45/45]2 laminations, depending on the plate boundary conditions, plate aspect ratios, and the hole size. Clamping the plate edges induces far stronger "anomalous" buckling behavior (enhancing compressive buckling strengths at increasing hole sizes) of the perforated MMC plates than simply supporting the plate edges.

Temperature-dependent phase-specific deformation mechanisms in a directionally solidified NiAl-Cr(Mo) lamellar composite

DOE PAGES

Yu, Dunji; An, Ke; Chen, Xu; ...

2015-10-09

Phase-specific thermal expansion and mechanical deformation behaviors of a directionally solidified NiAl–Cr(Mo) lamellar in situ composite were investigated by using real-time in situ neutron diffraction during compression at elevated temperatures up to 800 °C. Tensile and compressive thermal residual stresses were found to exist in the NiAl phase and Crss (solid solution) phase, respectively. Then, based on the evolution of lattice spacings and phase stresses, the phase-specific deformation behavior was analyzed qualitatively and quantitatively. Moreover, estimates of phase stresses were derived by Hooke's law on the basis of a simple method for the determination of stress-free lattice spacing in inmore » situ composites. During compressive loading, the NiAl phase yields earlier than the Crss phase. The Crss phase carries much higher stress than the NiAl phase, and displays consistent strain hardening at all temperatures. The NiAl phase exhibits strain hardening at relatively low temperatures and softening at high temperatures. During unloading, the NiAl phase yields in tension whereas the Crss phase unloads elastically. Additionally, post-test microstructural observations show phase-through cracks at room temperature, micro cracks along phase interfaces at 600 °C and intact lamellae kinks at 800 °C, which is due to the increasing deformability of both phases as temperature rises.« less

Foamed concrete containing rice husk ash as sand replacement: an experimental study on compressive strength

NASA Astrophysics Data System (ADS)

Rum, R. H. M.; Jaini, Z. M.; Boon, K. H.; Khairaddin, S. A. A.; Rahman, N. A.

2017-11-01

This study presents the utilization of rice husk ash (RHA) as sand replacement in foamed concrete. The study focuses on the effect of RHA on the compressive strength of foamed concrete. RHA contains high pozzolanic material that reacts with cementitious to enhance the strength and durability of foamed concrete. RHA also acts as filler causing the foamed concrete to become denser while retaining its unique low density. A total 243 cube specimens was prepared for the compression test. Two sets of mix design were employed at water-cement (W/C) ratio of 0.55, 0.60 and cement-sand ratio of 0.50, 0.33. The results revealed that the presence of RHA as sand replacement resulted in an increase in the compressive strength of foamed concrete. Moreover, 30% to 40% RHA was the optimum content level, contributing to the compressive strength of 18.1 MPa to 22.4 MPa. The W/C ratio and superplasticiser dosage play small roles in improving workability. In contrast, density governs the compressive strength of foamed concrete.

Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

NASA Technical Reports Server (NTRS)

Atchison, C S; Miller, James A

1942-01-01

Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

Proton MR spectroscopy in predicting the increase of perfusion MR imaging for WHO grade II gliomas.

PubMed

Guillevin, Remy; Menuel, Carole; Abud, Lucas; Costalat, Robert; Capelle, Laurent; Hoang-Xuan, Khê; Habas, Christophe; Chiras, Jacques; Vallée, Jean-Noel

2012-03-01

To investigate the correlation between the metabolite ratios obtained from proton magnetic resonance (MR) spectroscopy and those obtained from MR perfusion parameters (relative cerebral blood volume [rCBV]) in a cohort of low-grade glioma (LGG). Patients underwent prospectively conventional MR, proton magnetic resonance spectroscopy ((1) HMRS), and perfusion-weighted images (PWI). Statistical analyses were performed to determine the correlative and independent predictive factors of rCBVmax and the metabolite ratio thresholds with optimum sensitivity and specificity. Thirty-one patients were included in this study. Linear correlations were observed between the metabolic ratios (lactate [Lac]/creatine [Cr], choline [Cho]/N-acetyl-aspartate [NAA], free-lipids/Cr) and rCBVmax (P < 0.05). These metabolic ratios were determined to be independent predictive factors of rCBVmax (P = 0.027, 0.011 and 0.032, respectively). According to the receiver operating characteristic curves, the cutoff values of the metabolic ratios to discriminate between the two populations of rCBVmax (<1.7 versus = 1.7) were 1.72, 1.54, and 1.40, respectively, with a sensitivity = 75% and a specificity >95% for Lac/Cr. This study demonstrated consistent correlations between the data from (1) HMRS and PWI. The Lac/Cr ratio predicts regional hemodynamic changes, which are themselves a useful biomarker of clinical prognosis in patients with LGG. As such, this ratio may provide a new parameter for making improved clinical decisions. Copyright © 2011 Wiley-Liss, Inc.

Urine epidermal growth factor, monocyte chemoattractant protein-1 or their ratio as predictors of complete remission in primary glomerulonephritis.

PubMed

Chanrat, Eakkapat; Worawichawong, Supanat; Radinahamed, Piyanuch; Sathirapongsasuti, Nuankanya; Nongnuch, Arkom; Assanatham, Montira; Udomsubpayakul, Umaporn; Kitiyakara, Chagriya

2018-04-01

The balance of several cytokines likely influences the resolution of glomerulonephritis. Monocyte chemoattractant protein-1(MCP-1) is a chemokine that promotes renal inflammation whereas epidermal growth factor (EGF) stimulates protective responses. Previously, high urine MCP-1(MCP-1) and low urine EGF (EGF) levels were found to be associated with tubulointerstitial fibrosis, but there is limited information on the value of these mediators as predictors of therapeutic responses or long term outcome in primary glomerulonephritis. To determine the performance of urine EGF, MCP-1 or their ratio at baseline as biomarkers to predict complete remission, and the relationship of these mediators with subsequent renal function 24 months later in primary glomerulonephritis. This is a prospective study of patients with biopsy-proven primary glomerulonephritis. Baseline urine samples were collected at biopsy before therapy. MCP-1 and EGF were analyzed by enzyme-linked immunosorbent assays and expressed as a ratio to urine creatinine (ng/mgCr) or as EGF/MCP-1 ratio (ng/ng). Proteinuria and estimated glomerular filtration rate (eGRF) were monitored after therapy. Complete remission (CR) was defined as proteinuria ≤ 0.3 g/gCr. Median follow-up was 20 months. Of all patients (n = 74), 38 patients (51.4%) subsequently achieved CR. Baseline urine EGF and EGF/MCP-1 levels were significantly higher in CR compared to Not CR. By contrast, MCP-1 was not different. High EGF (EGF > 75 ng/mgCr) was a significant predictor (OR 2.28) for CR by multivariate analysis after adjusting for proteinuria, blood pressure, baseline eGFR. In patients who completed 24 months follow-up (n = 43), baseline EGF correlated inversely with proteinuria and positively with eGFR at 24 months. High urine EGF level is a promising biomarker of CR. Baseline EGF levels correlated with kidney function at 2 years. EGF/MCP-1 was not superior to EGF alone. Further studies are necessary to determine the role of urine EGF as a guide to therapy in primary GN. Copyright © 2018 Elsevier Ltd. All rights reserved.

The influence of high fat diets with different ketogenic ratios on the hippocampal accumulation of creatine - FTIR microspectroscopy study

NASA Astrophysics Data System (ADS)

Skoczen, A.; Setkowicz, Z.; Janeczko, K.; Sandt, Ch.; Borondics, F.; Chwiej, J.

2017-09-01

The main purpose of this study was the determination and comparison of anomalies in creatine (Cr) accumulation occurring within CA3 and DG areas of hippocampal formation as a result of two high-fat, carbohydrate-restricted ketogenic diets (KD) with different ketogenic ratio (KR). To reach this goal, Fourier transformed infrared microspectroscopy with synchrotron radiation source (SRFTIR microspectroscopy) was applied for chemical mapping of creatine absorption bands, occurring around 1304, 1398 and 2800 cm- 1. The samples were taken from three groups of experimental animals: control group (N) fed with standard laboratory diet, KD1 and KD2 groups fed with high-fat diets with KR 5:1 and 9:1 respectively. Additionally, the possible influence on the phosphocreatine (PhCr, the high energetic form of creatine) content was evaluated by comparative analysis of chemical maps obtained for creatine and for compounds containing phosphate groups which manifest in the spectra at the wavenumbers of around 1240 and 1080 cm- 1. Our results showed that KD2 strongly modifies the frequency of Cr inclusions in both analyzed hippocampal areas. Statistical analysis, performed with Mann-Whitney U test revealed increased accumulation of Cr within CA3 and DG areas of KD2 fed rats compared to both normal rats and KD1 experimental group. Moreover, KD2 diet may modify the frequency of PhCr deposits as well as the PhCr to Cr ratio.

Increased myo-inositol level in dorsolateral prefrontal cortex in migraine patients with major depression.

PubMed

Lirng, Jiing-Feng; Chen, Hung-Chieh; Fuh, Jong-Ling; Tsai, Chia-Fen; Liang, Jen-Feng; Wang, Shuu-Jiun

2015-07-01

Although the comorbidity between migraine and major depressive disorder (MDD) has been recognized, the pathophysiology remains unclear. The dorsolateral prefrontal cortex (DLPFC) is a well-known neural substrate for MDD. We investigated the relationship between brain metabolites in DLPFC and comorbid MDD in migraine patients. We recruited migraine patients from a tertiary headache clinic. A board-certified psychiatrist conducted a structured interview for MDD diagnosis. The severity of depression was evaluated by the Beck Depression Inventory (BDI). Thirty migraine patients (five men, 25 women; mean age: 40.4 ± 12.4 years) completed the study, and 16 of them were diagnosed with MDD. All patients underwent a magnetic resonance spectroscopy (MRS) examination focusing on bilateral DLPFC. The ratios of N-acetylaspartate (NAA), choline (Cho), and myo-inositol (mI) to total creatine (tCr) were compared between migraine patients with and without MDD, and were correlated with BDI scores. Relative to patients without MDD, migraine patients with MDD had higher mI/tCr ratios in the bilateral DLPFC (p = 0.02, left; p = 0.02, right, Mann-Whitney U test). The mI/tCr ratios in the right DLPFC were positively correlated with BDI scores (r = 0.52, p = 0.003). The NAA/tCr and Cho/tCr ratios did not differ between migraine patients with and without MDD. Increased mI/tCr within the DLPFC might be associated with the presence of MDD in migraine patients. © International Headache Society 2014.

A New Method to Produce Ni-Cr Ferroalloy Used for Stainless Steel Production

NASA Astrophysics Data System (ADS)

Chen, Pei-Xian; Chu, Shao-Jun; Zhang, Guo-Hua

2016-08-01

A new electrosilicothermic method has been proposed in the present paper to produce Ni-Cr ferroalloy, which can be used for the production of 300 series stainless steel. Based on this new process, the Ni-Si ferroalloy is first produced as the intermediate alloy, and then the desiliconization process of Ni-Si ferroalloy melt with chromium concentrate is carried out to generate Ni-Cr ferroalloy. The silicon content in the Ni-Si ferroalloy produced in the submerged arc furnace should be more than 15 mass% (for the propose of reducing dephosphorization), in order to make sure the phosphorus content in the subsequently produced Ni-Cr ferroalloy is less than 0.03 mass%. A high utilization ratio of Si and a high recovery ratio of Cr can be obtained after the desiliconization reaction between Ni-Si ferroalloy and chromium concentrate in the electric arc furnace (EAF)-shaking ladle (SL) process.

High-Strength Ultra-Fine-Grained Hypereutectic Al-Si-Fe-X (X = Cr, Mn) Alloys Prepared by Short-Term Mechanical Alloying and Spark Plasma Sintering.

PubMed

Průša, Filip; Bláhová, Markéta; Vojtěch, Dalibor; Kučera, Vojtěch; Bernatiková, Adriana; Kubatík, Tomáš František; Michalcová, Alena

2016-11-30

In this work, Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn (wt %) alloys were prepared by a combination of short-term mechanical alloying and spark plasma sintering. The microstructure was composed of homogeneously dispersed intermetallic particles forming composite-like structures. X-ray diffraction analysis and TEM + EDS analysis determined that the α-Al along with α-Al 15 (Fe,Cr)₃Si₂ or α-Al 15 (Fe,Mn)₃Si₂ phases were present, with dimensions below 130 nm. The highest hardness of 380 ± 7 HV5 was observed for the Al-20Si-10Fe-6Mn alloy, exceeding the hardness of the reference as-cast Al-12Si-1Cu-1 Mg-1Ni alloy (121 ± 2 HV5) by nearly a factor of three. Both of the prepared alloys showed exceptional thermal stability with the hardness remaining almost the same even after 100 h of annealing at 400 °C. Additionally, the compressive strengths of the Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn alloys reached 869 MPa and 887 MPa, respectively, and had virtually the same values of 870 MPa and 865 MPa, respectively, even after 100 h of annealing. More importantly, the alloys showed an increase in ductility at 400 °C, reaching several tens of percent. Thus, both of the investigated alloys showed better mechanical properties, including superior hardness, compressive strength and thermal stability, as compared to the reference Al-10Si-1Cu-1Mg-1Ni alloy, which softened remarkably, reducing its hardness by almost 50% to 63 ± 8 HV5.

High-Strength Ultra-Fine-Grained Hypereutectic Al-Si-Fe-X (X = Cr, Mn) Alloys Prepared by Short-Term Mechanical Alloying and Spark Plasma Sintering

PubMed Central

Průša, Filip; Bláhová, Markéta; Vojtěch, Dalibor; Kučera, Vojtěch; Bernatiková, Adriana; Kubatík, Tomáš František; Michalcová, Alena

2016-01-01

In this work, Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn (wt %) alloys were prepared by a combination of short-term mechanical alloying and spark plasma sintering. The microstructure was composed of homogeneously dispersed intermetallic particles forming composite-like structures. X-ray diffraction analysis and TEM + EDS analysis determined that the α-Al along with α-Al15(Fe,Cr)3Si2 or α-Al15(Fe,Mn)3Si2 phases were present, with dimensions below 130 nm. The highest hardness of 380 ± 7 HV5 was observed for the Al-20Si-10Fe-6Mn alloy, exceeding the hardness of the reference as-cast Al-12Si-1Cu-1 Mg-1Ni alloy (121 ± 2 HV5) by nearly a factor of three. Both of the prepared alloys showed exceptional thermal stability with the hardness remaining almost the same even after 100 h of annealing at 400 °C. Additionally, the compressive strengths of the Al-20Si-10Fe-6Cr and Al-20Si-10Fe-6Mn alloys reached 869 MPa and 887 MPa, respectively, and had virtually the same values of 870 MPa and 865 MPa, respectively, even after 100 h of annealing. More importantly, the alloys showed an increase in ductility at 400 °C, reaching several tens of percent. Thus, both of the investigated alloys showed better mechanical properties, including superior hardness, compressive strength and thermal stability, as compared to the reference Al-10Si-1Cu-1Mg-1Ni alloy, which softened remarkably, reducing its hardness by almost 50% to 63 ± 8 HV5. PMID:28774094

Risk Stratification of Acute Kidney Injury Using the Blood Urea Nitrogen/Creatinine Ratio in Patients With Acute Decompensated Heart Failure.

PubMed

Takaya, Yoichi; Yoshihara, Fumiki; Yokoyama, Hiroyuki; Kanzaki, Hideaki; Kitakaze, Masafumi; Goto, Yoichi; Anzai, Toshihisa; Yasuda, Satoshi; Ogawa, Hisao; Kawano, Yuhei

2015-01-01

Risk stratification of acute kidney injury (AKI) is important for acute decompensated heart failure (ADHF). The aim of this study was to determine whether clinical markers, such as the blood urea nitrogen/creatinine ratio (BUN/Cr) or BUN or creatinine values alone, stratify the risk of AKI for mortality. In all, 371 consecutive ADHF patients were enrolled in the study. AKI was defined as serum creatinine ≥0.3 mg/dl or a 1.5-fold increase in serum creatinine levels within 48 h. During ADHF therapy, AKI occurred in 99 patients; 55 patients died during the 12-month follow-up period. Grouping patients according to AKI and a median BUN/Cr at admission of 22.1 (non-AKI+low BUN/Cr, non-AKI+high BUN/Cr, AKI+low BUN/Cr, and AKI+high BUN/Cr groups) revealed higher mortality in the AKI+high BUN/Cr group (log-rank test, P<0.001). Cox's proportional hazard analysis revealed an association between AKI+high BUN/Cr and mortality, whereas the association with AKI+low BUN/Cr did not reach statistical significance. When patients were grouped according to AKI and median BUN or creatinine values at admission, AKI was associated with mortality, regardless of BUN or creatinine. The combination of AKI and elevated BUN/Cr, but not BUN or creatinine individually, is linked with an increased risk of mortality in ADHF patients, suggesting that the BUN/Cr is useful for risk stratification of AKI.

Fabrication and characterization of He-charged ODS-FeCrNi films deposited by a radio-frequency plasma magnetron sputtering technique

NASA Astrophysics Data System (ADS)

Song, Liang; Wang, Xianping; Wang, Le; Zhang, Ying; Liu, Wang; Jiang, Weibing; Zhang, Tao; Fang, Qianfeng; Liu, Changsong

2017-04-01

He-charged oxide dispersion strengthened (ODS) FeCrNi films were prepared by a radio-frequency (RF) plasma magnetron sputtering method in a He and Ar mixed atmosphere at 150 °C. As a comparison, He-charged FeCrNi films were also fabricated at the same conditions through direct current (DC) plasma magnetron sputtering. The doping of He atoms and Y2O3 in the FeCrNi films was realized by the high backscattered rate of He ions and Y2O3/FeCrNi composite target sputtering method, respectively. Inductive coupled plasma (ICP) and x-ray photoelectron spectroscopy (XPS) analysis confirmed the existence of Y2O3 in FeCrNi films, and Y2O3 content hardly changed with sputtering He/Ar ratio. Cross-sectional scanning electron microscopy (SEM) shows that the FeCrNi films were composed of dense columnar nanocrystallines and the thickness of the films was obviously dependent on He/Ar ratio. Nanoindentation measurements revealed that the FeCrNi films fabricated through DC/RF plasma magnetron sputtering methods exhibited similar hardness values at each He/Ar ratio, while the dispersion of Y2O3 apparently increased the hardness of the films. Elastic recoil detection (ERD) showed that DC/RF magnetron sputtered FeCrNi films contained similar He amounts (˜17 at.%). Compared with the minimal change of He level with depth in DC-sputtered films, the He amount decreases gradually in depth in the RF-sputtered films. The Y2O3-doped FeCrNi films were shown to exhibit much smaller amounts of He owing to the lower backscattering possibility of Y2O3 and the inhibition effect of nano-sized Y2O3 particles on the He element.

The Effect of Compression Ratio on Knock Limits of High-Performance Fuels in a CFR Engine II : Blends of 2,2,3-Trimethylpentane with 28-R

NASA Technical Reports Server (NTRS)

Tower, Leonard K

1945-01-01

The knock-limited performance of blends of 0,50; and 100 percent by volume of 2,2,3-trimethylpentane in 28-R fuel determined with a modified F-4 engine at three sets of conditions varying from severe to mild at each of three compression ratios (6.0, 8.0, and 10.0). A comparison of the knock-limited performance of 2,2,3-trimethylpentane with that of triptane (2,2,3-trimethylbutane) is included. The knock-Limited performance of 2,2,3-trimethylpontane was usually more sensitive to either compression ratio or inlet-air temperature than 28-R fuel, but the ratio of the knock-limited indicated mean effective pressure of a given blend containing 2,2,3-trimethypentane and 28-R to the indicated mean effective pressure of 28-R alone was not greatly affected by compression ratio if the engine operating conditions were mild. Although 2,2,3-trimethylpentane in general had a lower knock-limited performance than triptane, the characteristics of the two fuels were somewhat similar.

Compressed/reconstructed test images for CRAF/Cassini

NASA Technical Reports Server (NTRS)

Dolinar, S.; Cheung, K.-M.; Onyszchuk, I.; Pollara, F.; Arnold, S.

1991-01-01

A set of compressed, then reconstructed, test images submitted to the Comet Rendezvous Asteroid Flyby (CRAF)/Cassini project is presented as part of its evaluation of near lossless high compression algorithms for representing image data. A total of seven test image files were provided by the project. The seven test images were compressed, then reconstructed with high quality (root mean square error of approximately one or two gray levels on an 8 bit gray scale), using discrete cosine transforms or Hadamard transforms and efficient entropy coders. The resulting compression ratios varied from about 2:1 to about 10:1, depending on the activity or randomness in the source image. This was accomplished without any special effort to optimize the quantizer or to introduce special postprocessing to filter the reconstruction errors. A more complete set of measurements, showing the relative performance of the compression algorithms over a wide range of compression ratios and reconstruction errors, shows that additional compression is possible at a small sacrifice in fidelity.

Near-lossless multichannel EEG compression based on matrix and tensor decompositions.

PubMed

Dauwels, Justin; Srinivasan, K; Reddy, M Ramasubba; Cichocki, Andrzej

2013-05-01

A novel near-lossless compression algorithm for multichannel electroencephalogram (MC-EEG) is proposed based on matrix/tensor decomposition models. MC-EEG is represented in suitable multiway (multidimensional) forms to efficiently exploit temporal and spatial correlations simultaneously. Several matrix/tensor decomposition models are analyzed in view of efficient decorrelation of the multiway forms of MC-EEG. A compression algorithm is built based on the principle of “lossy plus residual coding,” consisting of a matrix/tensor decomposition-based coder in the lossy layer followed by arithmetic coding in the residual layer. This approach guarantees a specifiable maximum absolute error between original and reconstructed signals. The compression algorithm is applied to three different scalp EEG datasets and an intracranial EEG dataset, each with different sampling rate and resolution. The proposed algorithm achieves attractive compression ratios compared to compressing individual channels separately. For similar compression ratios, the proposed algorithm achieves nearly fivefold lower average error compared to a similar wavelet-based volumetric MC-EEG compression algorithm.

Marine and freshwater concentration ratios (CR(wo-water)): review of Japanese data.

PubMed

Tagami, K; Uchida, S

2013-12-01

The water-to-organism (whole body) concentration ratio (CR(wo-water)), which is defined as the ratio of the concentration of a radionuclide in the biota (Bq kg(-1) fresh weight) to that in water (Bq L(-1)), has been used in mathematical models for environmental radiation protection. In the present paper, published global fallout (90)Sr, (137)Cs, (106)Ru, (144)Ce and (239+240)Pu activity concentration data and stable element concentration data for Na, K, Ca, Mg, Fe, Cu and Mn for organisms living in freshwater or seawater areas in Japan were collated. The data suitable for obtaining CR(wo-water) values were identified. CR(wo-water) values of (137)Cs were similar for pelagic fish, benthic fish and whitebait (immature, small fish) with respective geometric means of 30 (range: 4.4-69), 32 (range: 15-54) and 33 (range: 13-84). The calculated CR(wo-water) values of the other radionuclides and stable elements were generally similar to other previously reported values; with the exception that those for Ce were lower for marine biota and those of Cu were higher for freshwater fish. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparison of GRCop-84 to Other High Thermal Conductive Cu Alloys

NASA Technical Reports Server (NTRS)

deGroh, Henry C., III; Ellis, David L.; Loewenthal, William S.

2007-01-01

The mechanical properties of five copper alloys (GRCop-84, AMZIRC, GlidCop Al-15, Cu-1Cr-0.1Zr, Cu-0.9Cr) competing in high temperature, high heat flux applications such as rocket nozzles, were compared. Tensile, creep, thermal expansion, and compression tests are presented. Tests were done on as-received material, and on material which received a simulated brazing heat treatment at 935 C. The 935 C heat treatment weakened AMZIRC, Cu-1Cr-0.1Zr, and Cu-0.9Cr, and the strength of as-received AMZIRC dropped precipitously as test temperatures exceeded 500 C. The properties of GlidCop Al-15 and GRCop-84 were not significantly affected by the 935 C heat treatment. Thus GRCop-84 is better than AMZIRC, Cu-1Cr-0.1Zr, and Cu-0.9Cr at temperatures greater than 500 C. Ductility was lowest in GlidCop Al-15 and Cu-0.9Cr. The creep properties of GRCop-84 were superior to those of brazed AMZIRC, Cu-1Cr-0.1Zr, and Cu-0.9Cr. At equivalent rupture life and stress, GRCop-84 had a 150 C temperature advantage over brazed AMZIRC; for equivalent rupture life and temperature GRCop-84 was two times stronger. The advantages of GRCop-84 over GlidCop Al-15 associated with ease of processing were confirmed by GlidCop s marginal ductility. In the post brazed condition, GRCop-84 was found to be superior to the other alloys due to its greater strength and creep resistance (compared to AMZIRC, Cu-1Cr-0.1Zr, and Cu-0.9Cr) and ductility (compared to GlidCop Al-15)

Optimal Compression Methods for Floating-point Format Images

NASA Technical Reports Server (NTRS)

Pence, W. D.; White, R. L.; Seaman, R.

2009-01-01

We report on the results of a comparison study of different techniques for compressing FITS images that have floating-point (real*4) pixel values. Standard file compression methods like GZIP are generally ineffective in this case (with compression ratios only in the range 1.2 - 1.6), so instead we use a technique of converting the floating-point values into quantized scaled integers which are compressed using the Rice algorithm. The compressed data stream is stored in FITS format using the tiled-image compression convention. This is technically a lossy compression method, since the pixel values are not exactly reproduced, however all the significant photometric and astrometric information content of the image can be preserved while still achieving file compression ratios in the range of 4 to 8. We also show that introducing dithering, or randomization, when assigning the quantized pixel-values can significantly improve the photometric and astrometric precision in the stellar images in the compressed file without adding additional noise. We quantify our results by comparing the stellar magnitudes and positions as measured in the original uncompressed image to those derived from the same image after applying successively greater amounts of compression.

Effects on the Physical and Mechanical Properties of Porous Concrete for Plant Growth of Blast Furnace Slag, Natural Jute Fiber, and Styrene Butadiene Latex Using a Dry Mixing Manufacturing Process.

PubMed

Kim, Hwang-Hee; Kim, Chun-Soo; Jeon, Ji-Hong; Park, Chan-Gi

2016-01-29

To evaluate the effects of industrial by-products materials on the performance of porous concrete for plant growth, this study investigated the physical, strength, and freeze/thaw resistances of porous concrete for plant growth, prepared by replacing cement with blast furnace slag powder at 60% by weight, and replacing natural stone aggregates with coarse blast furnace slag aggregates at rates of 0%, 20%, 40%, 60% and 100% by weight. In addition, the effects of adding natural jute fiber and styrene butadiene ( SB) latex to these concrete mixtures were evaluated. The void ratio, compressive strength, and freeze/thaw resistance of the samples were measured. With increasing replacement rate of blast furnace aggregates, addition of latex, and mixing of natural jute fiber the void ratio of the concrete was increased. Compressive strength decreased as the replacement rate of blast-furnace slag aggregates increased. The compressive strength decreased after 100 freeze/thaw cycles, regardless of the replacement rate of blast furnace slag aggregates or of the addition of natural jute fiber and latex. The addition of natural jute fiber and latex decreased the compressive strength after 100 freeze/thaw cycles. The test results indicate that the control mixture satisfied the target compressive strength of 10 MPa and the target void ratio of 25% at replacement rates of 0% and 20% for blast furnace aggregates, and that the mixtures containing latex satisfied the criteria up to an aggregate replacement rate of 60%. However, the mixtures containing natural jute fiber did not satisfy these criteria. The relationship between void ratio and residual compressive strength after 100 freeze/thaw cycles indicates that the control mixture and the mixtures containing jute fiber at aggregate replacement rates of 20% and 40% satisfied the target void ratio of 25% and the target residual compressive strength of over 80% after 100 freeze/thaw cycles. The mixtures containing latex and aggregate replacement rates up to 60% satisfied the target void ratio and compressive strength.

Effects on the Physical and Mechanical Properties of Porous Concrete for Plant Growth of Blast Furnace Slag, Natural Jute Fiber, and Styrene Butadiene Latex Using a Dry Mixing Manufacturing Process

PubMed Central

Kim, Hwang-Hee; Kim, Chun-Soo; Jeon, Ji-Hong; Park, Chan-Gi

2016-01-01

To evaluate the effects of industrial by-products materials on the performance of porous concrete for plant growth, this study investigated the physical, strength, and freeze/thaw resistances of porous concrete for plant growth, prepared by replacing cement with blast furnace slag powder at 60% by weight, and replacing natural stone aggregates with coarse blast furnace slag aggregates at rates of 0%, 20%, 40%, 60% and 100% by weight. In addition, the effects of adding natural jute fiber and styrene butadiene (SB) latex to these concrete mixtures were evaluated. The void ratio, compressive strength, and freeze/thaw resistance of the samples were measured. With increasing replacement rate of blast furnace aggregates, addition of latex, and mixing of natural jute fiber the void ratio of the concrete was increased. Compressive strength decreased as the replacement rate of blast-furnace slag aggregates increased. The compressive strength decreased after 100 freeze/thaw cycles, regardless of the replacement rate of blast furnace slag aggregates or of the addition of natural jute fiber and latex. The addition of natural jute fiber and latex decreased the compressive strength after 100 freeze/thaw cycles. The test results indicate that the control mixture satisfied the target compressive strength of 10 MPa and the target void ratio of 25% at replacement rates of 0% and 20% for blast furnace aggregates, and that the mixtures containing latex satisfied the criteria up to an aggregate replacement rate of 60%. However, the mixtures containing natural jute fiber did not satisfy these criteria. The relationship between void ratio and residual compressive strength after 100 freeze/thaw cycles indicates that the control mixture and the mixtures containing jute fiber at aggregate replacement rates of 20% and 40% satisfied the target void ratio of 25% and the target residual compressive strength of over 80% after 100 freeze/thaw cycles. The mixtures containing latex and aggregate replacement rates up to 60% satisfied the target void ratio and compressive strength. PMID:28787883

Residual Stresses in a NiCrY-Coated Powder Metallurgy Disk Superalloy

NASA Technical Reports Server (NTRS)

Gabb, Timothy P.; Rogers, Richard B.; Nesbitt, James A.; Puleo, Bernadette J.; Miller, Robert A.; Telesman, Ignacy; Draper, Susan L.; Locci, Ivan E.

2017-01-01

Protective ductile coatings will be necessary to mitigate oxidation and corrosion attack on superalloy disks exposed to increasing operating temperatures in some turbine engine environments. However, such coatings must be resistant to harmful surface cracking during service. The objective of this study was to investigate how residual stresses evolve in such coatings. Cylindrical gage fatigue specimens of powder metallurgy-processed disk superalloy LSHR were coated with a NiCrY coating, shot peened, and then subjected to fatigue in air at room and high temperatures. The effects of shot peening and fatigue cycling on average residual stresses and other aspects of the coating were assessed. Shot peening did induce beneficial compressive residual stresses in the coating and substrate. However, these stresses became more tensile in the coating with subsequent heating and contributed to cracking of the coating in long intervals of cycling at 760 C. Substantial compressive residual stresses remained in the substrate adjacent to the coating, sufficient to suppress fatigue cracking. The coating continued to protect the substrate from hot corrosion pitting, even after fatigue cracks initiated in the coating.

The Microstructural Evolution and Special Flow Behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr During Isothermal Compression at a Low Strain Rate

NASA Astrophysics Data System (ADS)

Sun, J. Z.; Li, M. Q.; Li, H.

2017-09-01

The microstructural evolution and special flow behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr during isothermal compression at a strain rate of 0.0001 s-1 were investigated. The dislocation climbs in elongated α grains resulted in the formation of low-angle boundaries that transform into high-angle boundaries with greater deformation, and the elongated α grains subsequently separated into homogenous globular α grains with the penetration of the β phase. The simultaneous occurrence of discontinuous dynamic recrystallization and continuous dynamic recrystallization in the primary β grains resulted in a trimode grain distribution. The β grains surrounded by dislocations presented an equilateral-hexagonal morphology, which suggests that grain boundary sliding through dislocation climbs was the main deformation mechanism. The true stress-strain curves for 1073 and 1113 K abnormally intersect at a strain of 0.35, related to the α → β phase transformation and distinct growth of the β grain size.

Anomaly in the dynamic strength of austenitic stainless steel 12Cr19Ni10Ti under shock wave loading

NASA Astrophysics Data System (ADS)

Garkushin, G. V.; Kanel, G. I.; Razorenov, S. V.; Savinykh, A. S.

2017-07-01

Measurement results for the shock wave compression profiles of 12Cr19Ni10Ti steel and its dynamic strength in the strain rate range 105-106 s-1 are presented. The protracted viscous character of the spall fracture is revealed. With the previously obtained data taken into account, the measurement results are described by a polynomial relation, which can be used to construct the fracture kinetics. On the lower boundary of the range, the resistance to spall fracture is close to the value of the true strength of the material under standard low-rate strain conditions; on the upper boundary, the spall strength is more than twice greater than this quantity. An increase in the temperature results in a decrease in both the dynamic limit of elasticity and the spall fracture strength of steel. The most interesting result is the anomaly in the dependence of the spall fracture strength on the duration of the shock wave compression pulse, which is related to the formation of deformation martensite near the growing discontinuities.

Clinical utility of wavelet compression for resolution-enhanced chest radiography

NASA Astrophysics Data System (ADS)

Andriole, Katherine P.; Hovanes, Michael E.; Rowberg, Alan H.

2000-05-01

This study evaluates the usefulness of wavelet compression for resolution-enhanced storage phosphor chest radiographs in the detection of subtle interstitial disease, pneumothorax and other abnormalities. A wavelet compression technique, MrSIDTM (LizardTech, Inc., Seattle, WA), is implemented which compresses the images from their original 2,000 by 2,000 (2K) matrix size, and then decompresses the image data for display at optimal resolution by matching the spatial frequency characteristics of image objects using a 4,000- square matrix. The 2K-matrix computed radiography (CR) chest images are magnified to a 4K-matrix using wavelet series expansion. The magnified images are compared with the original uncompressed 2K radiographs and with two-times magnification of the original images. Preliminary results show radiologist preference for MrSIDTM wavelet-based magnification over magnification of original data, and suggest that the compressed/decompressed images may provide an enhancement to the original. Data collection for clinical trials of 100 chest radiographs including subtle interstitial abnormalities and/or subtle pneumothoraces and normal cases, are in progress. Three experienced thoracic radiologists will view images side-by- side on calibrated softcopy workstations under controlled viewing conditions, and rank order preference tests will be performed. This technique combines image compression with image enhancement, and suggests that compressed/decompressed images can actually improve the originals.

The effect of epileptic seizures on proton MRS visible neurochemical concentrations.

PubMed

Simister, Robert J; McLean, Mary A; Salmenpera, Tuuli M; Barker, Gareth J; Duncan, John S

2008-09-01

To investigate post-ictal changes in cerebral metabolites. We performed a longitudinal quantitative proton magnetic resonance spectroscopy (MRS) study in 10 patients with epilepsy and 10 control subjects. The patients were studied on two occasions: immediately following a seizure, and on a second occasion at least 7h after the most recent seizure. Each study measured N-acetyl aspartate plus N-acetyl aspartyl glutamate (NAAt), Creatine plus phosphocreatine (Cr), Choline containing compounds (Cho) and glutamate plus glutamine (GLX) concentrations using a short-echo time sequence (TE=30ms), and NAAt, Cr and lactate using a second sequence with longer echo time (TE=144ms). The control group was studied on two occasions using the same sequences. No inter-scan differences were observed for the control group. NAAt and NAAt/Cr levels were lower in the patient group at both measured TEs but did not change significantly between studies. The ratio of Cr at TE 144ms to TE 30ms (Cr(144)/Cr(30)) and GLX/Cr were higher and Cho lower in the post-ictal scan compared to the inter-ictal study. Change in Cr(144)/Cr(30) and NAAt(144)/Cr(144) correlated with the post-ictal interval. Lactate measurement at longer TE was not informative. Proton MRS is sensitive to metabolite changes following epileptic seizures within the immediate post-ictal period. The ratio Cr(144)/Cr(30) is the most sensitive measure of metabolic disturbance and is highest in the post-ictal period but appears to normalise within 2h of the most recent seizure.

Elastic Modulus Measurement of ORNL ATF FeCrAl Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Zachary T.; Terrani, Kurt A.; Yamamoto, Yukinori

2015-10-01

Elastic modulus and Poisson’s ratio for a number of wrought FeCrAl alloys, intended for accident tolerant fuel cladding application, are determined via resonant ultrasonic spectroscopy. The results are reported as a function of temperature from room temperature to 850°C. The wrought alloys were in the fully annealed and unirradiated state. The elastic modulus for the wrought FeCrAl alloys is at least twice that of Zr-based alloys over the temperature range of this study. The Poisson’s ratio of the alloys was 0.28 on average and increased very slightly with increasing temperature.

Serum and urinary thioredoxin concentrations are associated with severity of children hydronephrosis.

PubMed

Xu, Zhe-Ming; Li, Min-Ju; Tao, Chang

2017-03-01

Ureteropelvic junction obstruction (UPJO) is the most common cause of hydronephrosis in children. This study was to assess the relationship between serum thioredoxin (S-Trx) and urinary thioredoxin (U-Trx) concentrations and severity of children hydronephrosis caused by UPJO. This study included 156 hydronephrosis children with unilateral UPJO and 80 healthy children. S-Trx and U-Trx concentrations were measured using enzyme-linked immunosorbent assay. U-Trx/creatinine (cr) ratio was calculated. S-Trx and U-Trx concentrations and U-Trx/cr ratio were significantly higher in hydronephrosis children than in healthy children. They were significantly correlated with split renal function, anterior-posterior diameter and Society for Fetal Urology classification, as well as were independently related to the split renal function <39.2%, anterior-posterior diameter>30mm and Society for Fetal Urology grade IV. Under receiver operating characteristic curves, U-Trx/cr ratio showed the higher predictive value compared to S-Trx and U-Trx concentrations. Increased S-Trx and U-Trx concentrations, especially U-Trx/cr ratio, are closely associated with the severity of children hydronephrosis, substantializing Trx as a promising biomarker for the progression of children hydronephrosis. Copyright © 2017 Elsevier B.V. All rights reserved.

The new American Heart Association cardiopulmonary resuscitation guidelines: should children and adults have to share?

PubMed

Sherman, Mindy

2007-06-01

The latest American Heart Association guidelines for pediatric cardiopulmonary resuscitation (CPR) were published in December 2005. Changes from the 2000 guidelines were directed toward simplifying CPR. Infants, children, and adults now share the same recommendation for the initial compression:ventilation ratio. This is a significant change for pediatricians trained in the importance of a respiratory etiology of pediatric cardiopulmonary arrest. The present review will focus on the rationale behind these guideline changes. The new guidelines for single rescuer CPR include a compression:ventilation ratio of 30: 2 for both adult and pediatric victims. The impetus for this recommendation is based on recent appreciation for the deleterious effects of hyperventilation as well as an attempt to increase bystander delivery of CPR. The physiologic results of hyperventilation are discussed. The new pediatric basic life support guideline changes are underscored. Research representing the spectrum of opinions on the optimal compression:ventilation ratio, including compression-only CPR, is presented. Although based primarily on adult, animal, and computational models, the new compression:ventilation ratio, recommended for both initial pediatric and adult CPR, is a reasonable recommendation. The simplified CPR guidelines released in 2005 will hopefully contribute to improved bystander delivery of CPR and improved outcome.

Digitized hand-wrist radiographs: comparison of subjective and software-derived image quality at various compression ratios.

PubMed

McCord, Layne K; Scarfe, William C; Naylor, Rachel H; Scheetz, James P; Silveira, Anibal; Gillespie, Kevin R

2007-05-01

The objectives of this study were to compare the effect of JPEG 2000 compression of hand-wrist radiographs on observer image quality qualitative assessment and to compare with a software-derived quantitative image quality index. Fifteen hand-wrist radiographs were digitized and saved as TIFF and JPEG 2000 images at 4 levels of compression (20:1, 40:1, 60:1, and 80:1). The images, including rereads, were viewed by 13 orthodontic residents who determined the image quality rating on a scale of 1 to 5. A quantitative analysis was also performed by using a readily available software based on the human visual system (Image Quality Measure Computer Program, version 6.2, Mitre, Bedford, Mass). ANOVA was used to determine the optimal compression level (P < or =.05). When we compared subjective indexes, JPEG compression greater than 60:1 significantly reduced image quality. When we used quantitative indexes, the JPEG 2000 images had lower quality at all compression ratios compared with the original TIFF images. There was excellent correlation (R2 >0.92) between qualitative and quantitative indexes. Image Quality Measure indexes are more sensitive than subjective image quality assessments in quantifying image degradation with compression. There is potential for this software-based quantitative method in determining the optimal compression ratio for any image without the use of subjective raters.

Physiological, physical and behavioural changes in dogs (Canis familiaris) when kennelled: testing the validity of stress parameters.

PubMed

Part, C E; Kiddie, J L; Hayes, W A; Mills, D S; Neville, R F; Morton, D B; Collins, L M

2014-06-22

Domestic dogs (Canis familiaris) housed in kennelling establishments are considered at risk of suffering poor welfare. Previous research supporting this hypothesis has typically used cortisol:creatinine ratios (C/Cr) to measure acute and chronic stress in kennelled dogs. However, the value of C/Cr as a welfare indicator has been questioned. This study aimed to test the validity of a range of physiological, physical and behavioural welfare indicators and to establish baseline values reflecting good dog welfare. Measurements were taken from 29 privately-owned dogs (14 males, 15 females), ranging in age and breed, in their own home and in a boarding kennel environment, following a within-subjects, counterbalanced design. Pairwise comparisons revealed that C/Cr and vanillylmandelic acid:creatinine ratios (VMA/Cr) were higher in the kennel than home environment (P=0.003; P=0.01, respectively) and were not associated with differences in movement/exercise between environments. Dogs' surface temperature was lower in kennels (P=0.001) and was not associated with ambient temperature. No association with age, or effects of kennel establishment, kennelling experience, sex or source were found. Dogs were generally more active in kennels, but showed considerable individual variability. C/Cr and 5-HIAA:creatinine ratios (5-HIAA/Cr) were negatively correlated with lip licking in kennels. Baseline values for each parameter are presented. The emotional valence of responses was ambiguous and no definitive evidence was found to suggest that dogs were negatively stressed by kennelling. It was concluded that C/Cr and, particularly, VMA/Cr and surface temperature provide robust indicators of psychological arousal in dogs, while spontaneous behaviour might be better used to facilitate interpretation of physiological and physical data on an individual level. Copyright © 2014 Elsevier Inc. All rights reserved.

Fast quantification of proton magnetic resonance spectroscopic imaging with artificial neural networks

NASA Astrophysics Data System (ADS)

Bhat, Himanshu; Sajja, Balasrinivasa Rao; Narayana, Ponnada A.

2006-11-01

Accurate quantification of the MRSI-observed regional distribution of metabolites involves relatively long processing times. This is particularly true in dealing with large amount of data that is typically acquired in multi-center clinical studies. To significantly shorten the processing time, an artificial neural network (ANN)-based approach was explored for quantifying the phase corrected (as opposed to magnitude) spectra. Specifically, in these studies radial basis function neural network (RBFNN) was used. This method was tested on simulated and normal human brain data acquired at 3T. The N-acetyl aspartate (NAA)/creatine (Cr), choline (Cho)/Cr, glutamate + glutamine (Glx)/Cr, and myo-inositol (mI)/Cr ratios in normal subjects were compared with the line fitting (LF) technique and jMRUI-AMARES analysis, and published values. The average NAA/Cr, Cho/Cr, Glx/Cr and mI/Cr ratios in normal controls were found to be 1.58 ± 0.13, 0.9 ± 0.08, 0.7 ± 0.17 and 0.42 ± 0.07, respectively. The corresponding ratios using the LF and jMRUI-AMARES methods were 1.6 ± 0.11, 0.95 ± 0.08, 0.78 ± 0.18, 0.49 ± 0.1 and 1.61 ± 0.15, 0.78 ± 0.07, 0.61 ± 0.18, 0.42 ± 0.13, respectively. These results agree with those published in literature. Bland-Altman analysis indicated an excellent agreement and minimal bias between the results obtained with RBFNN and other methods. The computational time for the current method was 15 s compared to approximately 10 min for the LF-based analysis.

Effect of the patient education - Learning and Coping strategies - in cardiac rehabilitation on return to work at one year: a randomised controlled trial show (LC-REHAB).

PubMed

Bitsch, Birgitte Laier; Nielsen, Claus Vinther; Stapelfeldt, Christina Malmose; Lynggaard, Vibeke

2018-05-21

Personal resources are identified as important for the ability to return to work (RTW) for patients with ischaemic heart disease (IHD) or heart failure (HF) undergoing cardiac rehabilitation (CR). The patient education 'Learning and Coping' (LC) addresses personal resources through a pedagogical approach. This trial aimed to assess effect of adding LC strategies in CR compared to standard CR measured on RTW status at one-year follow-up after CR. In an open parallel randomised controlled trial, patients with IHD or HF were block-randomised in a 1:1 ratio to the LC arm (LC plus CR) or the control arm (CR alone) across three Danish hospital units. Eligible patients were aged 18 to ≤60 and had not left the labour market. The intervention was developed from an inductive pedagogical approach consisting of individual interviews and group based teaching by health professionals with experienced patients as co-educators. The control arm consisted of deductive teaching (standard CR). RTW status was derived from the Danish Register for Evaluation of Marginalisation (DREAM). Blinding was not possible. The effect was evaluated by logistic regression analysis and reported as crude and adjusted odds ratios (OR) with 95% confidence interval (CI). The population for the present analysis was N = 244 (LC arm: n = 119 versus control arm: n = 125). No difference in RTW status was found at one year across arms (LC arm: 64.7% versus control arm: 68.8%, adjusted odds ratio OR: 0.76, 95% CI: 0.43-1.31). Addition of LC strategies in CR showed no improvement in RTW at one year follow-up. www.clinicaltrials.gov identifier NCT01668394. First Posted: August 20, 2012.

A Lossless hybrid wavelet-fractal compression for welding radiographic images.

PubMed

Mekhalfa, Faiza; Avanaki, Mohammad R N; Berkani, Daoud

2016-01-01

In this work a lossless wavelet-fractal image coder is proposed. The process starts by compressing and decompressing the original image using wavelet transformation and fractal coding algorithm. The decompressed image is removed from the original one to obtain a residual image which is coded by using Huffman algorithm. Simulation results show that with the proposed scheme, we achieve an infinite peak signal to noise ratio (PSNR) with higher compression ratio compared to typical lossless method. Moreover, the use of wavelet transform speeds up the fractal compression algorithm by reducing the size of the domain pool. The compression results of several welding radiographic images using the proposed scheme are evaluated quantitatively and compared with the results of Huffman coding algorithm.

An image assessment study of image acceptability of the Galileo low gain antenna mission

NASA Technical Reports Server (NTRS)

Chuang, S. L.; Haines, R. F.; Grant, T.; Gold, Yaron; Cheung, Kar-Ming

1994-01-01

This paper describes a study conducted by NASA Ames Research Center (ARC) in collaboration with the Jet Propulsion Laboratory (JPL), Pasadena, California on the image acceptability of the Galileo Low Gain Antenna mission. The primary objective of the study is to determine the impact of the Integer Cosine Transform (ICT) compression algorithm on Galilean images of atmospheric bodies, moons, asteroids and Jupiter's rings. The approach involved fifteen volunteer subjects representing twelve institutions involved with the Galileo Solid State Imaging (SSI) experiment. Four different experiment specific quantization tables (q-table) and various compression stepsizes (q-factor) to achieve different compression ratios were used. It then determined the acceptability of the compressed monochromatic astronomical images as evaluated by Galileo SSI mission scientists. Fourteen different images were evaluated. Each observer viewed two versions of the same image side by side on a high resolution monitor, each was compressed using a different quantization stepsize. They were requested to select which image had the highest overall quality to support them in carrying out their visual evaluations of image content. Then they rated both images using a scale from one to five on its judged degree of usefulness. Up to four pre-selected types of images were presented with and without noise to each subject based upon results of a previously administered survey of their image preferences. Fourteen different images in seven image groups were studied. The results showed that: (1) acceptable compression ratios vary widely with the type of images; (2) noisy images detract greatly from image acceptability and acceptable compression ratios; and (3) atmospheric images of Jupiter seem to have higher compression ratios of 4 to 5 times that of some clear surface satellite images.

Inductively coupled plasma mass spectrometry with a twin quadrupole instrument using laser ablation sample introduction and monodisperse dried microparticulate injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, Lloyd A.

1996-10-17

The focus of this dissertation is the use of a twin quadrupole inductively coupled plasma mass spectrometer (ICP-MS) for the simultaneous detection of two m/z values. The twin quadrupole ICP-MS is used with laser ablation sample introduction in both the steady state (10 Hz) and single pulse modes. Steady state signals are highly correlated and the majority of flicker noise cancels when the ratio is calculated. Using a copper sample, the isotope ratio 63Cu +/ 65Cu + is measured with a relative standard deviation (RSD) of 0.26%. Transient signals for single laser pulses are also obtained. Copper isotope ratio measurementsmore » for several laser pulses are measured with an RSD of 0.85%. Laser ablation (LA) is used with steel samples to assess the ability of the twin quadrupole ICP-MS to eliminate flicker noise of minor components of steel samples. Isotopic and internal standard ratios are measured in the first part of this work. The isotope ratio 52Cr +/ 53Cr + (Cr present at 1.31 %) can be measured with an RSD of 0.06 % to 0.1 %. For internal standard elements, RSDs improve from 1.9 % in the Cr + signal to 0.12% for the ratio of 51V + to 52Cr +. In the second part of this work, one mass spectrometer is scanned while the second channel measures an individual m/z value. When the ratio of these two signals is calculated, the peak shapes in the mass spectrum are improved significantly. Pulses of analyte and matrix ions from individual drops are measured simultaneously using the twin quadrupole ICP-MS with monodisperse dried microparticulate injection (MDMI). At modest Pb concentrations (500 ppm), a shoulder on the leading edge of the Li + signal becomes apparent. Space charge effects are consistent with the disturbances seen.« less

[Comparison among three translucency parameters].

PubMed

Fang, Xiong; Hui, Xia

2017-06-01

This study aims to compare the three commonly used translucency parameters in prosthodontics: transmittance (T), contrast ratio (CR), and translucency parameter (TP). Six platelet specimens were composed of Vita enamel and dental porcelain. The initial thickness was 1.2 mm. The specimens were gradually ground to 1.0, 0.8, 0.6, 0.4, and 0.2 mm. T, color parameters, and reflection were measured by a spectrocolorimeter for each corresponding thickness. T, CR and TP were calculated and compared. TP increased, whereas CR decreased, with decreasing thickness. Moreover, 
T increased with decreasing thickness, and exponential relationships were found. Two-way ANOVA showed statistical significance between T and thickness, except between T and the 1.2 mm and 1.0 mm enamel porcelain groups. No difference was found among the coefficient variations (CV) of T, CR and TP. Curve fitting indicated the existence of exponential relationships between T and CR and between T and TP. The values for goodness of fit with statistical significance were 0.951 and 0.939, respectively (P<0.05). Under the experimental conditions, T, TP and CR achieved the same CV. T and TP, as well as T and CR, were found with exponential relationships. The value of CR and TP could not represent the translucency precisely, especially when comparing the changing ratios.

Ocular biometric parameters among 3-year-old Chinese children: testability, distribution and association with anthropometric parameters

PubMed Central

Huang, Dan; Chen, Xuejuan; Gong, Qi; Yuan, Chaoqun; Ding, Hui; Bai, Jing; Zhu, Hui; Fu, Zhujun; Yu, Rongbin; Liu, Hu

2016-01-01

This survey was conducted to determine the testability, distribution and associations of ocular biometric parameters in Chinese preschool children. Ocular biometric examinations, including the axial length (AL) and corneal radius of curvature (CR), were conducted on 1,688 3-year-old subjects by using an IOLMaster in August 2015. Anthropometric parameters, including height and weight, were measured according to a standardized protocol, and body mass index (BMI) was calculated. The testability was 93.7% for the AL and 78.6% for the CR overall, and both measures improved with age. Girls performed slightly better in AL measurements (P = 0.08), and the difference in CR was statistically significant (P < 0.05). The AL distribution was normal in girls (P = 0.12), whereas it was not in boys (P < 0.05). For CR1, all subgroups presented normal distributions (P = 0.16 for boys; P = 0.20 for girls), but the distribution varied when the subgroups were combined (P < 0.05). CR2 presented a normal distribution (P = 0.11), whereas the AL/CR ratio was abnormal (P < 0.001). Boys exhibited a significantly longer AL, a greater CR and a greater AL/CR ratio than girls (all P < 0.001). PMID:27384307

Contrast volume to creatinine clearance ratio for the prediction of contrast-induced nephropathy in patients undergoing coronary angiography or percutaneous intervention.

PubMed

Barbieri, Lucia; Verdoia, Monica; Marino, Paolo; Suryapranata, Harry; De Luca, Giuseppe

2016-06-01

Contrast-induced nephropathy is a common complication of procedures that are likely to use contrast media. The identification of high-risk patients and preventive optimal hydration are key measures to reduce the incidence of contrast-induced nephropathy. The aim of this study was to evaluate the role of the contrast volume to creatinine clearance ratio (V/CrCl) in the prediction of contrast-induced nephropathy after coronary angiography or percutaneous coronary intervention. Our population consisted of 2308 consecutive patients undergoing coronary angiography and/or percutaneous coronary intervention. The risk of contrast-induced nephropathy was evaluated across quartiles of the V/CrCl. Receiver operating characteristic curves were used to identify the best predictive value. Contrast-induced nephropathy was defined as an absolute increase of 0.5 mg/dL or a relative increase of >25% in creatinine levels 24-48 hours after the procedure. The total incidence of contrast-induced nephropathy was 12.2% and was significantly higher in the fourth quartile (first quartile 8.8%, second quartile 8.9%, third quartile 11.6% and fourth quartile 19.4%; P < 0.001). Using receiver operating characteristic curves we identified V/CrCl ≥ 6.15 as the best discriminant value for the prediction of contrast-induced nephropathy, which occurred in 25.1% of patients with V/CrCl ≥ 6.15 versus 9.7% in patients with V/CrCl < 6.15. These results were also confirmed at multivariate analysis after correction for all baseline confounders (adjusted odds ratio (AOR) (95% confidence interval (CI)) 1.81 (1.19-2.76); P = 0.005). The association between V/CrCl > 6.15 and an increased risk of contrast-induced nephropathy was confirmed among diabetic (11% vs. 27.7%; p P < 0.001) and non-diabetic patients (8.9% vs. 23%; Pp < 0.001), also after correction for all baseline confounders. This is one of the largest studies evaluating the association between the V/CrCl ratio and the risk of contrast-induced nephropathy in patients undergoing coronary angiography or percutaneous coronary intervention. We found that a V/CrCl ratio >6.15 was independently associated with an increased risk of contrast-induced nephropathy. © The European Society of Cardiology 2015.

SUPERNOVA DRIVING. II. COMPRESSIVE RATIO IN MOLECULAR-CLOUD TURBULENCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Liubin; Padoan, Paolo; Haugbølle, Troels

2016-07-01

The compressibility of molecular cloud (MC) turbulence plays a crucial role in star formation models, because it controls the amplitude and distribution of density fluctuations. The relation between the compressive ratio (the ratio of powers in compressive and solenoidal motions) and the statistics of turbulence has been previously studied systematically only in idealized simulations with random external forces. In this work, we analyze a simulation of large-scale turbulence (250 pc) driven by supernova (SN) explosions that has been shown to yield realistic MC properties. We demonstrate that SN driving results in MC turbulence with a broad lognormal distribution of themore » compressive ratio, with a mean value ≈0.3, lower than the equilibrium value of ≈0.5 found in the inertial range of isothermal simulations with random solenoidal driving. We also find that the compressibility of the turbulence is not noticeably affected by gravity, nor are the mean cloud radial (expansion or contraction) and solid-body rotation velocities. Furthermore, the clouds follow a general relation between the rms density and the rms Mach number similar to that of supersonic isothermal turbulence, though with a large scatter, and their average gas density probability density function is described well by a lognormal distribution, with the addition of a high-density power-law tail when self-gravity is included.« less

Long-term Brain Tissue Monitoring after Semi-brain Irradiation in Rats Using Proton Magnetic Resonance Spectroscopy: A Preliminary Study In vivo

PubMed Central

Chen, Hong; Cheng, Yu-Shu; Zhou, Zheng-Rong

2017-01-01

Background: In head and neck neoplasm survivors treated with brain irradiation, metabolic alterations would occur in the radiation-induced injury area. The mechanism of these metabolic alterations has not been fully understood, while the alternations could be sensitively detected by proton (1H) nuclear magnetic resonance spectroscopy (MRS). In this study, we investigated the metabolic characteristics of radiation-induced brain injury through a long-term follow-up after radiation treatment using MRS in vivo. Methods: A total of 12 adult Sprague-Dawley rats received a single dose of 30 Gy radiation treatment to semi-brain (field size: 1.0 cm × 2.0 cm; anterior limit: binocular posterior inner canthus connection; posterior limit: external acoustic meatus connection; internal limit: sagittal suture). Conventional magnetic resonance imaging and single-voxel 1H-MRS were performed at different time points (in month 0 before irradiation as well as in the 1st, 3rd, 5th, 7th, and 9th months after irradiation) to investigate the alternations in irradiation field. N-acetylaspartate/choline (NAA/Cho), NAA/creatinine (Cr), and Cho/Cr ratios were measured in the bilateral hippocampus and quantitatively analyzed with a repeated-measures mixed-effects model and multiple comparison test. Results: Significant changes in the ratios of NAA/Cho (F = 57.37, Pg < 0.001), NAA/Cr (F = 54.49, Pg < 0.001), and Cho/Cr (F = 9.78, Pg = 0.005) between the hippocampus region of the irradiated semi-brain and the contralateral semi-brain were observed. There were significant differences in NAA/Cho (F = 9.17, Pt < 0.001) and NAA/Cr (F = 13.04, Pt < 0.001) ratios over time. The tendency of NAA/Cr to change with time showed no significant difference between the irradiated and contralateral sides. Nevertheless, there were significant differences in the Cho/Cr ratio between these two sides. Conclusions: MRS can sensitively detect metabolic alternations. Significant changes of metabolites ratio in the first few months after radiation treatment reflect the metabolic disturbance in the acute and early-delayed stages of radiation-induced brain injuries. PMID:28397726

JPEG vs. JPEG 2000: an objective comparison of image encoding quality

NASA Astrophysics Data System (ADS)

Ebrahimi, Farzad; Chamik, Matthieu; Winkler, Stefan

2004-11-01

This paper describes an objective comparison of the image quality of different encoders. Our approach is based on estimating the visual impact of compression artifacts on perceived quality. We present a tool that measures these artifacts in an image and uses them to compute a prediction of the Mean Opinion Score (MOS) obtained in subjective experiments. We show that the MOS predictions by our proposed tool are a better indicator of perceived image quality than PSNR, especially for highly compressed images. For the encoder comparison, we compress a set of 29 test images with two JPEG encoders (Adobe Photoshop and IrfanView) and three JPEG2000 encoders (JasPer, Kakadu, and IrfanView) at various compression ratios. We compute blockiness, blur, and MOS predictions as well as PSNR of the compressed images. Our results show that the IrfanView JPEG encoder produces consistently better images than the Adobe Photoshop JPEG encoder at the same data rate. The differences between the JPEG2000 encoders in our test are less pronounced; JasPer comes out as the best codec, closely followed by IrfanView and Kakadu. Comparing the JPEG- and JPEG2000-encoding quality of IrfanView, we find that JPEG has a slight edge at low compression ratios, while JPEG2000 is the clear winner at medium and high compression ratios.

Regularized spherical polar fourier diffusion MRI with optimal dictionary learning.

PubMed

Cheng, Jian; Jiang, Tianzi; Deriche, Rachid; Shen, Dinggang; Yap, Pew-Thian

2013-01-01

Compressed Sensing (CS) takes advantage of signal sparsity or compressibility and allows superb signal reconstruction from relatively few measurements. Based on CS theory, a suitable dictionary for sparse representation of the signal is required. In diffusion MRI (dMRI), CS methods proposed for reconstruction of diffusion-weighted signal and the Ensemble Average Propagator (EAP) utilize two kinds of Dictionary Learning (DL) methods: 1) Discrete Representation DL (DR-DL), and 2) Continuous Representation DL (CR-DL). DR-DL is susceptible to numerical inaccuracy owing to interpolation and regridding errors in a discretized q-space. In this paper, we propose a novel CR-DL approach, called Dictionary Learning - Spherical Polar Fourier Imaging (DL-SPFI) for effective compressed-sensing reconstruction of the q-space diffusion-weighted signal and the EAP. In DL-SPFI, a dictionary that sparsifies the signal is learned from the space of continuous Gaussian diffusion signals. The learned dictionary is then adaptively applied to different voxels using a weighted LASSO framework for robust signal reconstruction. Compared with the start-of-the-art CR-DL and DR-DL methods proposed by Merlet et al. and Bilgic et al., respectively, our work offers the following advantages. First, the learned dictionary is proved to be optimal for Gaussian diffusion signals. Second, to our knowledge, this is the first work to learn a voxel-adaptive dictionary. The importance of the adaptive dictionary in EAP reconstruction will be demonstrated theoretically and empirically. Third, optimization in DL-SPFI is only performed in a small subspace resided by the SPF coefficients, as opposed to the q-space approach utilized by Merlet et al. We experimentally evaluated DL-SPFI with respect to L1-norm regularized SPFI (L1-SPFI), which uses the original SPF basis, and the DR-DL method proposed by Bilgic et al. The experiment results on synthetic and real data indicate that the learned dictionary produces sparser coefficients than the original SPF basis and results in significantly lower reconstruction error than Bilgic et al.'s method.

The Preparation of Porous Sol-Gel Silica with Metal Organic Framework MIL-101(Cr) by Microwave-Assisted Hydrothermal Method for Adsorption Chillers

PubMed Central

Uma, Kasimayan; Pan, Guan-Ting; Yang, Thomas C.-K.

2017-01-01

Metal organic framework (MOF) of MIL-101(Cr)-Silica (SiO2) composites with highly mesoporous and uniform dispersions were synthesized by a microwave-assisted hydrothermal method followed by the sol-gel technique. Water vapor adsorption experiments were conducted on the MIL-101(Cr)-SiO2 composites for industrial adsorption chiller applications. The effects of MIL-101(Cr)-SiO2 mixing ratios (ranging from 0% to 52%), the surface area and amount of Lewis and Brønsted sites were comprehensively determined through water vapor adsorption experiments and the adsorption mechanism is also explained. The BET and Langmuir results indicate that the adsorption isotherms associated with the various MIL-101(Cr)-SiO2 ratios demonstrated Type I and IV adsorption behavior, due to the mesoporous structure of the MIL-101(Cr)-SiO2. It was observed that the increase in the amount of Lewis and Brønsted sites on the MIL-101(Cr)-SiO2 composites significantly improves the water vapor adsorption efficiency, for greater stability during the water vapor adsorption experiments. PMID:28772969

A safer disposal of hazardous phosphate coating sludge by formation of an amorphous calcium phosphate matrix.

PubMed

Navarro-Blasco, I; Duran, A; Pérez-Nicolás, M; Fernández, J M; Sirera, R; Alvarez, J I

2015-08-15

Phosphate coating hazardous wastes originated from the automotive industry were efficiently encapsulated by an acid-base reaction between phosphates present in the sludge and calcium aluminate cement, yielding very inert and stable monolithic blocks of amorphous calcium phosphate (ACP). Two different compositions of industrial sludge were characterized and loaded in ratios ranging from 10 to 50 wt.%. Setting times and compressive strengths were recorded to establish the feasibility of this method to achieve a good handling and a safe landfilling of these samples. Short solidification periods were found and leaching tests showed an excellent retention for toxic metals (Zn, Ni, Cu, Cr and Mn) and for organic matter. Retentions over 99.9% for Zn and Mn were observed even for loadings as high as 50 wt.% of the wastes. The formation of ACP phase of low porosity and high stability accounted for the effective immobilization of the hazardous components of the wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessment of ferrous chloride and Portland cement for the remediation of chromite ore processing residue.

PubMed

Jagupilla, Santhi C; Wazne, Mahmoud; Moon, Deok Hyun

2015-10-01

Chromite Ore Processing Residue (COPR) is an industrial waste containing up to 7% chromium (Cr) including up to 5% hexavalent chromium [Cr(VI)]. The remediation of COPR has been challenging due to the slow release of Cr(VI) from a clinker like material and thereby the incomplete detoxification of Cr(VI) by chemical reagents. The use of sulfur based reagents such as ferrous sulfate and calcium polysulfide to detoxify Cr(VI) has exasperated the swell potential of COPR upon treatment. This study investigated the use of ferrous chloride alone and in combination with Portland cement to address the detoxification of Cr(VI) in COPR and the potential swell of COPR. Chromium regulatory tests, X-ray powder diffraction (XRPD) analyses and X-ray absorption near edge structure (XANES) analyses were used to assess the treatment results. The treatment results indicated that Cr(VI) concentrations for the acid pretreated micronized COPR as measured by XANES analyses were below the New Jersey Department of Environmental Protection (NJDEP) standard of 20 mg kg(-1). The Toxicity characteristic leaching procedure (TCLP) Cr concentrations for all acid pretreated samples also were reduced below the TCLP regulatory limit of 5 mg L(-1). Moreover, the TCLP Cr concentration for the acid pretreated COPR with particle size ⩽0.010 mm were less than the universal treatment standard (UTS) of 0.6 mg L(-1). The treatment appears to have destabilized all COPR potential swell causing minerals. The unconfined compressive strength (UCS) for the treated samples increased significantly upon treatment with Portland cement. Copyright © 2015 Elsevier Ltd. All rights reserved.

Rapid-Rate Compression Testing of Sheet Materials at High Temperatures

NASA Technical Reports Server (NTRS)

Bernett, E. C.; Gerberich, W. W.

1961-01-01

This Report describes the test equipment that was developed and the procedures that were used to evaluate structural sheet-material compression properties at preselected constant strain rates and/or loads. Electrical self-resistance was used to achieve a rapid heating rate of 200 F/sec. Four materials were tested at maximum temperatures which ranged from 600 F for the aluminum alloy to 2000 F for the Ni-Cr-Co iron-base alloy. Tests at 0.1, 0.001, and 0.00001 in./in./sec showed that strain rate has a major effect on the measured strength, especially at the high temperatures. The tests, under conditions of constant temperature and constant compression stress, showed that creep deformation can be a critical factor even when the time involved is on the order of a few seconds or less. The theoretical and practical aspects of rapid-rate compression testing are presented, and suggestions are made regarding possible modifications of the equipment which would improve the over-all capabilities.

Size Distribution and Estimated Respiratory Deposition of Total Chromium, Hexavalent Chromium, Manganese, and Nickel in Gas Metal Arc Welding Fume Aerosols

PubMed Central

Cena, Lorenzo G.; Chisholm, William P.; Keane, Michael J.; Cumpston, Amy; Chen, Bean T.

2016-01-01

A laboratory study was conducted to determine the mass of total Cr, Cr(VI), Mn, and Ni in 15 size fractions for mild and stainless steel gas-metal arc welding (GMAW) fumes. Samples were collected using a nano multi orifice uniform deposition impactor (MOUDI) with polyvinyl chloride filters on each stage. The filters were analyzed by inductively coupled plasma mass spectrometry (ICP-MS) and ion chromatography. Limits of detection (LODs) and quantitation (LOQs) were experimentally calculated and percent recoveries were measured from spiked metals in solution and dry, certified welding-fume reference material. The fraction of Cr(VI) in total Cr was estimated by calculating the ratio of Cr(VI) to total Cr mass for each particle size range. Expected, regional deposition of each metal was estimated according to respiratory-deposition models. The weight percent (standard deviation) of Mn in mild steel fumes was 9.2% (6.8%). For stainless steel fumes, the weight percentages were 8.4% (5.4%) for total Cr, 12.2% (6.5%) for Mn, 2.1% (1.5%) for Ni and 0.5% (0.4%) for Cr(VI). All metals presented a fraction between 0.04 and 0.6 μm. Total Cr and Ni presented an additional fraction <0.03 μm. On average 6% of the Cr was found in the Cr(VI) valence state. There was no statistical difference between the smallest and largest mean Cr(VI) to total Cr mass ratio (p-value D 0.19), hence our analysis does not show that particle size affects the contribution of Cr(VI) to total Cr. The predicted total respiratory deposition for the metal particles was ∼25%. The sites of principal deposition were the head airways (7–10%) and the alveolar region (11–14%). Estimated Cr(VI) deposition was highest in the alveolar region (14%). PMID:26848207

Size Distribution and Estimated Respiratory Deposition of Total Chromium, Hexavalent Chromium, Manganese, and Nickel in Gas Metal Arc Welding Fume Aerosols.

PubMed

Cena, Lorenzo G; Chisholm, William P; Keane, Michael J; Cumpston, Amy; Chen, Bean T

A laboratory study was conducted to determine the mass of total Cr, Cr(VI), Mn, and Ni in 15 size fractions for mild and stainless steel gas-metal arc welding (GMAW) fumes. Samples were collected using a nano multi orifice uniform deposition impactor (MOUDI) with polyvinyl chloride filters on each stage. The filters were analyzed by inductively coupled plasma mass spectrometry (ICP-MS) and ion chromatography. Limits of detection (LODs) and quantitation (LOQs) were experimentally calculated and percent recoveries were measured from spiked metals in solution and dry, certified welding-fume reference material. The fraction of Cr(VI) in total Cr was estimated by calculating the ratio of Cr(VI) to total Cr mass for each particle size range. Expected, regional deposition of each metal was estimated according to respiratory-deposition models. The weight percent (standard deviation) of Mn in mild steel fumes was 9.2% (6.8%). For stainless steel fumes, the weight percentages were 8.4% (5.4%) for total Cr, 12.2% (6.5%) for Mn, 2.1% (1.5%) for Ni and 0.5% (0.4%) for Cr(VI). All metals presented a fraction between 0.04 and 0.6 μ m. Total Cr and Ni presented an additional fraction <0.03 μ m. On average 6% of the Cr was found in the Cr(VI) valence state. There was no statistical difference between the smallest and largest mean Cr(VI) to total Cr mass ratio ( p -value D 0.19), hence our analysis does not show that particle size affects the contribution of Cr(VI) to total Cr. The predicted total respiratory deposition for the metal particles was ∼25%. The sites of principal deposition were the head airways (7-10%) and the alveolar region (11-14%). Estimated Cr(VI) deposition was highest in the alveolar region (14%).

Differences in the direction of change of cerebral function parameters are evident over three years in HIV-infected individuals electively commencing initial cART.

PubMed

Winston, Alan; Puls, Rebekah; Kerr, Stephen J; Duncombe, Chris; Li, Patrick; Gill, John M; Ramautarsing, Reshmie; Taylor-Robinson, Simon D; Emery, Sean; Cooper, David A

2015-01-01

Changes in cerebral metabolite ratios (CMR) measured on 1H-MRS and changes in cognitive function (CF) are described in subjects commencing combination antiretroviral therapy (cART), although the dynamics of such changes are poorly understood. Neuroasymptomatic, HIV-infected subjects electively commencing cART were eligible. CMR were assessed in three anatomical voxels and CF assessed at baseline, week 48 and week 144. Overall differences in absolute change in CMRs and CF parameters between 0-48 and 48-144 weeks were assessed. Twenty-two subjects completed study procedures. Plasma HIV-RNA was <50 copies/mL in all at week 48 and in all, but two subjects at week 144. In general, between weeks 0-48 a rise in N-acetyl-aspartate(NAA)/Creatine(Cr) ratio and a decline in myo-Inositol(mI)/Cr ratio were observed. Between weeks 48-144, small rises in NAA/Cr ratio were observed in two anatomical voxels, whereas a rise in mI/Cr ratio was observed in all anatomical locations (0.31 (0.66) and -0.27 (1.35) between weeks 0-48 and 0.13 (0.91) and 1.13 (1.71) between weeks 48-144 for absolute changes in NAA/Cr and mI/Cr (SD) in frontal-grey voxel, respectively). Global CF score improved between weeks 0-48 and then declined between weeks 48-144 (0.63 (1.16) and -0.63 (0.1.41) for mean absolute change (SD) between weeks 0-48 and weeks 48-144, respectively). The direction of change of cerebral function parameters differs over time in HIV-infected subjects commencing cART, highlighting the need for long-term follow-up in such studies. The changes we have observed between weeks 48-144 may represent the initial development of cerebral toxicities from cART.

Regulation of organic nucleic acids and serum biochemistry parameters by dietary chromium picolinate supplementation in swine model.

PubMed

Jiajun, Yang; Aiyun, Han; Shanshan, Zheng; Minhong, Zhang

2011-04-01

The relationships between chromium and metabolism are sophisticated. Organic nucleic acids and serum biochemistry parameters are affected by dietary chromium levels. The objective of this work was to study the effect of chromium picolinate (CrPic) supplementation on total DNA and RNA contents, the ratio of RNA/DNA in muscle and in pancreatic tissue, the level of insulin receptor (IR) mRNA and some serum biochemistry parameters in a porcine model. Young animals (48) were assigned randomly into three groups of 16 piglets, fed with three different dietary levels of Cr (common basal feedstuff alone or supplemented with CrPic at a dose of 1.61 μg/g or 3.22 μg/g, which corresponds to 0.2 μg/g and 0.4 μg/g Cr). After 80 days, the animals were sacrificed and skeletal muscle and pancreatic tissues were analyzed to detect differences caused by different levels of dietary Cr. The total content of RNA in muscle was increased significantly (P<0.05) in the CrPic supplemented groups. There was no significant difference between groups in the concentrations of total RNA in the pancreas or DNA in the muscle and pancreatic tissues. The RNA/DNA ratio in pancreas showed no significant change but the ratio was increased significantly (P<0.05) in muscle. There was a slight increase of the mRNA level of IR but there was no significant difference between groups. The content of serum cholesterol and insulin were reduced significantly (P<0.05) in the CrPic-supplemented groups and the content of high-density lipoprotein cholesterol (HDLC) was increased significantly (P<0.05) as the CrPic dose increased. There was a slight (non-significant) reduction of the concentrations of serum triglyceride and low-density lipoprotein cholesterol (LDLC) in the CrPic supplementation groups. Supplementary CrPic caused no significant change of muscular mRNA level of IR in healthy animals. An increased content of RNA in muscle, improved cholesterol metabolism and improved insulin sensitivity were found in these CrPic-treated groups in the porcine model. Copyright © 2011 Elsevier GmbH. All rights reserved.

Detecting the spatial chirp signals by fractional Fourier lens with transformation materials

NASA Astrophysics Data System (ADS)

Chen, J.; Hu, J.

2018-02-01

Fractional Fourier transform (FrFT) is the general form of the Fourier transform and is an important tool in signal processing. As one typical application of FrFT, detecting the chirp rate (CR, or known as the rate of frequency change) of a chirp signal is important in many optical measurements. The optical FrFT that based on graded index lens fails to detect the high CR chirp because the short wave propagation distance of the impulse in the lens will weaken the paraxial approximation condition. With the help of transformation optics, the improved FrFT lens is proposed to adjust the high CR as well as the impulse location of the given input chirp signal. The designed transformation materials can implement the effect of space compression, making the input chirp signal is equivalent to have lower CR, therefore the system can satisfy the paraxial approximation better. As a result, this lens can improve the detection precision for the high CR. The numerical simulations verified the design. The proposed device may have both theoretical and practical values, and the design demonstrates the ability and flexibility of TO in spatial signal processing.

Study by the Prandtl-Glauert method of compressibility effects and critical Mach number for ellipsoids of various aspect ratios and thickness ratios

NASA Technical Reports Server (NTRS)

Hess, Robert V; Gardner, Clifford S

1947-01-01

By using the Prandtl-Glauert method that is valid for three-dimensional flow problems, the value of the maximum incremental velocity for compressible flow about thin ellipsoids at zero angle of attack is calculated as a function of the Mach number for various aspect ratios and thickness ratios. The critical Mach numbers of the various ellipsoids are also determined. The results indicate an increase in critical Mach number with decrease in aspect ratio which is large enough to explain experimental results on low-aspect-ratio wings at zero lift.

First-principles study on the structure, elastic properties, hardness and electronic structure of TMB4 (TM=Cr, Re, Ru and Os) compounds

NASA Astrophysics Data System (ADS)

Pan, Y.; Zheng, W. T.; Guan, W. M.; Zhang, K. H.; Fan, X. F.

2013-11-01

The structural formation, elastic properties, hardness and electronic structure of TMB4 (TM=Cr, Re, Ru and Os) compounds are investigated using first-principles approach. The value of C22 for these compounds is almost two times bigger than the C11 and C33. The intrinsic hardness, shear modulus and Young's modulus are calculated to be in a sequence of CrB4>ReB4>RuB4>OsB4, and the Poisson's ratio and B/G ratio of TMB4 follow the order of CrB4

[Effect of anshen jielu recipe in intervening cerebral metabolism in rats with generalized anxiety disorder using magnetic resonance spectroscopy].

PubMed

Tang, Qi-sheng; Li, Ning; Luo, Bin

2011-01-01

To study the metabolic change in brain of rats with generalized anxiety disorder (GAD) and the intervention effect with Anshen Jielu Recipe (AJR) on it. Eight rats selected from 32 Wistar rats as normal group, the others were established as GAD model by using uncertainty empty water bottles method. Then the GAD rats were randomly divided into the model group (saline, by gastrogavage), the control group [buspirone hydrochloride, 2.0 mg/(kg x d), by gastrogavage], the treatment group [AJR, 12.5 g/(kg x d), by gastrogavage], 8 in each group, all were treated for 7 days. The concentration of cerebral metabolites, including N-acetyl aspartate (NAA), choline (Cho), creatine (Cr) and glutamate (Glu), in bilateral prefrontal cortex and hippocampus were measured using high-field strong super-conductivity (7.0T) animal MRI; and the ratio of NAA/Cr, Cho/Cr and Glu/Cr were calculated. The effect of AJR intervention was evaluated by changes of MRI before and after rats being treated with AJR for 7 days. Rats with GAD showed lowered ratios of NAA/Cr and Cho/Cr, and elevated Glu/Cr ratio in the right prefrontal cortex than those in normal rats. After AJR intervention, the abnormal changes in the three indices were restored to certain extents. AJR has apparent antianxiety effect in rats with GAD, with the effect initiation faster than that in the control group. Its mechanism is probably correlated with the regulation of abnormal metabolism in the brain.

Compound-specific carbon, nitrogen, and hydrogen isotopic ratios for amino acids in CM and CR chondrites and their use in evaluating potential formation pathways

NASA Astrophysics Data System (ADS)

Elsila, Jamie E.; Charnley, Steven B.; Burton, Aaron S.; Glavin, Daniel P.; Dworkin, Jason P.

2012-09-01

Stable hydrogen, carbon, and nitrogen isotopic ratios (δD, δ13C, and δ15N) of organic compounds can reveal information about their origin and formation pathways. Several formation mechanisms and environments have been postulated for the amino acids detected in carbonaceous chondrites. As each proposed mechanism utilizes different precursor molecules, the isotopic signatures of the resulting amino acids may indicate the most likely of these pathways. We have applied gas chromatography with mass spectrometry and combustion isotope ratio mass spectrometry to measure the compound-specific C, N, and H stable isotopic ratios of amino acids from seven CM and CR carbonaceous chondrites: CM1/2 Allan Hills (ALH) 83100, CM2 Murchison, CM2 Lewis Cliff (LEW) 90500, CM2 Lonewolf Nunataks (LON) 94101, CR2 Graves Nunataks (GRA) 95229, CR2 Elephant Moraine (EET) 92042, and CR3 Queen Alexandra Range (QUE) 99177. We compare the isotopic compositions of amino acids in these meteorites with predictions of expected isotopic enrichments from potential formation pathways. We observe trends of decreasing δ13C and increasing δD with increasing carbon number in the α-H, α-NH2 amino acids that correspond to predictions made for formation via Strecker-cyanohydrin synthesis. We also observe light δ13C signatures for β-alanine, which may indicate either formation via Michael addition or via a pathway that forms primarily small, straight-chain, amine-terminal amino acids (n-ω-amino acids). Higher deuterium enrichments are observed in α-methyl amino acids, indicating formation of these amino acids or their precursors in cold interstellar or nebular environments. Finally, individual amino acids are more enriched in deuterium in CR chondrites than in CM chondrites, reflecting different parent-body chemistry.

Postictal in situ MRS brain lactate in the rat kindling model.

PubMed

Maton, B M; Najm, I M; Wang, Y; Lüders, H O; Ng, T C

1999-12-10

To determine the temporal and spatial extent of the lactate (Lact) changes as correlated with seizure characteristics and EEG changes in the rat kindling model. Prior studies using MRS have detected cerebral Lact postictally in animal models of seizures and in patients with intractable focal epilepsy. We performed MRS in sham control rats (n = 4) and in rats stimulated in the right hippocampus at two different stages of the kindling and at three time points after the seizures: <2 hours (n = 8 and 5, stage 0 and stage 5), 2 to 3 hours (n = 5 and 6), and >3 hours (n = 4 and 2). Lact/creatine (Cr) and N-acetylaspartate (NAA)/Cr ratios were measured in six contiguous voxels (three left, three right) covering the hippocampi, anterior and posterior regions, and compared with EEG and ictal behavior. Lact/Cr ratios were measured at a very low level in the sham control rats and in the >3-hour group. In the <2-hour group, Lact/Cr increase was higher in stage-5 rats as compared with stage-0 rats (p = 0.001, unpaired t-test) and sham control rats when all the voxels were considered. Lact/Cr ratios were higher in the stimulated area as compared with all other brain areas in stage-0 rats (p = 0.05, paired t-test) but not in the stage-5 rats. Similar results with more inter-animal variability were measured in the 2- to 3-hour group. NAA/Cr ratios increased significantly after stage-0 kindling in the stimulated hippocampus but not after stage-5 kindling. Postictal Lact increase as assayed by MRS correlates with EEG and behavioral seizures and suggests that it would be an additional noninvasive technique for seizure localization during the presurgical evaluation of patients with intractable focal epilepsy.

Stiffness and Poisson ratio in longitudinal compression of fiber yarns in meso-FE modelling of composite reinforcement forming

NASA Astrophysics Data System (ADS)

Wang, D.; Naouar, N.; Vidal-Salle, E.; Boisse, P.

2018-05-01

In meso-scale finite element modeling, the yarns of the reinforcement are considered to be solids made of a continuous material in contact with their neighbors. The present paper consider the mechanical behavior of these yarns that can happen for some loadings of the reinforcement. The yarns present a specific mechanical behavior when under longitudinal compression because they are made up of a large number of fibers, Local buckling of the fibers causes the compressive stiffness of the continuous material representing the yarn to be much weaker than when under tension. In addition, longitudinal compression causes an important transverse expansion. It is shown that the transverse expansion can be depicted by a Poisson ratio that remained roughly constant when the yarn length and the compression strain varied. Buckling of the fibers significantly increases the transverse dimensions of the yarn which leads to a large Poisson ratio (up to 12 for a yarn analyzed in the present study). Meso-scale finite element simulations of reinforcements with binder yarns submitted to longitudinal compression showed that these improvements led to results in good agreement with micro-CT analyses.

Decreased Urinary Sodium-to-urinary Creatinine Ratio Identifies Sodium Depletion in Pediatric Acute Gastroenteritis.

PubMed

Heinz-Erian, P; Akdar, Z; Haerter, B; Waldegger, S; Giner, T; Scholl-Bürgi, S; Mueller, T

2016-01-01

In acute gastroenteritis (AG) fecal losses may cause depletion of sodium (NaD) which may not be recognized because of normal plasma Na (pNa) concentrations. We studied the incidence of this state of normonatremic sodium depletion (NNaD) and the suitability of the urinary Na/urinary creatinine ratio (uNa/uCr) for diagnosing NNaD. 16 AG- and 16 healthy control children aged 0.8-15.0 years. Prospective cross sectional pilot study. Measurements of Na, K and creatinine in plasma (p) and urine (u). Calculation of uNa/uCr Ratio, fractional excretion of Na (FENa) and uNa/uK ratio as the hitherto best known parameters of prerenal Na depletion, respectively. pNa concentrations were normal in 15/16 AG patients (93.8%) with only one subnormal value of 133 mmol/L, and a mean value of 137.9±2.3 mmol/L not different from the normal control group (139.4±2.2 mmol/L). Also, mean uNa concentrations and uNa/uK ratios did not differ between both groups. However, uNa/uCr ratios were below normal in 13/16 AG children (81.3%) but normal in all healthy controls with a significantly lower mean value in the AG group (12.6±8.8 vs. 31.2±8.3 mmol/mmol; p<0.0001). Similarly, 14/16 AG patients (87.5%) had a decreased FENa<0.5% with a mean FENa value significantly lower than in controls (0.36±0.28% vs. 0.95±0.26%, p<0.0001). The good agreement between FENa and uNa/uCr results was also reflected by a high correlation coefficient of r=0.9333. The majority of AG patients was found to have NNaD as determined by uNa/uCr and FENa. Calculation of uNa/uCr may be useful for diagnosing NNaD in AG. © Georg Thieme Verlag KG Stuttgart · New York.

Research on the compressive strength of basic magnesium salts and cyanide slag solidified body

NASA Astrophysics Data System (ADS)

Tu, Yubo; Han, Peiwei; Ye, Shufeng; Wei, Lianqi; Zhang, Xiaomeng; Fu, Guoyan; Yu, Bo

2018-02-01

The solidification of cyanide slag by using basic magnesium salts could reduce pollution and protect the environment. Experiments were carried out to investigate the effects of age, mixing amount of cyanide slag, water cement ratio and molar ratio of MgO to MgSO4 on the compressive strength of basic magnesium salts and cyanide slag solidified body in the present paper. It was found that compressive strength of solidified body increased with the increase of age, and decreased with the increase of mixing amount of cyanide slag and water cement ratio. The molar ratio of MgO to MgSO4 should be controlled in the range from 9 to 11 when the mixing amount of cyanide slag was larger than 80 mass%.

Chronic intermittent but not constant hypoxia decreases NAA/Cr ratios in neonatal mouse hippocampus and thalamus.

PubMed

Douglas, Robert M; Miyasaka, Naoyuki; Takahashi, Kan; Latuszek-Barrantes, Adrianna; Haddad, Gabriel G; Hetherington, Hoby P

2007-03-01

Chronic constant hypoxia (CCH) and chronic intermittent hypoxia (CIH) are known to have deleterious effects on the central nervous system. Because of the difference in the pattern of hypoxic exposure, it is possible that the pathological outcome would vary. The N-acetyl aspartate/creatine (NAA/Cr) ratio is a reliable marker of neuronal integrity, and this can be noninvasively measured by proton nuclear magnetic resonance spectroscopy. P2 CD1 mouse pups with their dams were exposed to either CCH, where the Fi(O(2)) was maintained at 11% continuously or to CIH, where the Fi(O(2)) was varied between 21 and 11% every 4 min. P30 mice exposed to intermittent hypoxia for 4 wk demonstrated a significant decrease in the NAA/Cr ratio in the hippocampus and thalamus, which was reversed by a subsequent exposure to 4 wk of normoxia. Meanwhile, mice exposed to 4 wk of constant hypoxia did not demonstrate any differences in their NAA/Cr ratios from controls in these brain regions. These results indicate that an intermittent pattern of hypoxic exposure may have a more adverse effect on neuronal function and integrity than a continuous one. The reversal of NAA/Cr levels to baseline during the return to normoxia indicates that therapeutic strategies targeted at alleviating the intermittent hypoxic stress in diseases, such as obstructive sleep apnea, have the potential for inducing significant neurocognitive recovery in these patients.

Higher visceral fat is associated with lower cerebral N-acetyl-aspartate ratios in middle-aged adults.

PubMed

Kaur, Sonya; Birdsill, Alex C; Steward, Kayla; Pasha, Evan; Kruzliak, Peter; Tanaka, Hirofumi; Haley, Andreana P

2017-06-01

Excessive adipose tissue, particularly with a central distribution, consists of visceral fat, which is metabolically active and could impinge upon central nervous system functioning. The aim of the current study was to examine levels of visceral adiposity in relation to key cerebral metabolite ratios localized in the occipitoparietal grey matter. Seventy-three adults, aged between 40 and 60 years, underwent structural magnetic resonance imaging and single voxel 1 H Magnetic Resonance Spectroscopy ( 1 H MRS). Visceral fat was assessed using Dual Energy X Ray Absorptiometry (DXA). Individuals with higher visceral fat mass and volume had significantly lower ratios of N-acetyl-aspartate to total creatine (phosphocreatine + creatine, PCr + Cr) (NAA/PCr + Cr) (β = -0.29, p = 0.03, β = -0.28, p = 0.04). They also had significantly higher ratios of myo-inositol to total creatine (mI/PCr + Cr ) (β = 0.36, p = 0.01, β = 0.36, p = 0.01). Visceral fat mass and volume were not significantly related to ratios of glutamate to total creatine (Glu/PCr + Cr). While future studies are necessary, these results indicate central adiposity is associated with metabolic changes that could impinge upon the central nervous system in middle age.

[Clinical Significance of Urinary Microalbumin to Creatinine Ratio in Physical Examinations].

PubMed

Guo, Qin; Luo, Wei; Yin, Dai-shu; Jia, Cheng-yao

2016-01-01

To-determine the association between urinary microalbumin to creatinine ratio (mALB/Cr) and metabolic indicators in people undergoing physical examinations. A total of 4 184 people who took physical examinations in West China Hospital, Sichuan University from November 2013 to October 2014 participated in this study. We measured their body mass index (BMI), systolic blood pressure (SBP), diastolic blood pressure (DBP), waistline, hipline, Waist-to-hip ratio (WHR), urinary mALB/Cr, serum glucose (GLU), total cholesterol (TC), triglyceride (TG) , high density lipoprotein cholesterol (HDL-C), low density lipoprotein cholesterol (LDL-C), blood urea nitrogen (BUN), serum creatinine (SCr) , uric acid (UA), cystatin C (Cys-C), glomerular filtration rate (eGFR) and homocysteine (Hcy). (1) The participants had a median (interquartile range) mALB/Cr of 5.7 (3.1-11.8) mg/g: 5.4 (3.0-11.3) mg/g for males and 6.3 (3.6-13.2) mg/g for females (P < 0.05). (2) About 10.95% participants (10.96% for males and 10.90% for females) had a mALB/Cr ≥ 30 mg/g. (3) mALB/Cr increased with age. (4) BMI, SBP, DBP, waistline, WHR, GLU, HDL-C, TG, SCr, BUN, UA, eGFR and Cys-C were associated the distribution of participants (P < 0.05) across the three groups of mALB/Cr: normal (< 30 mg/g), microalbuminuria (30-300 mg/g) , and proteinuria (> 300 mg/g). (5) Logistic regression demonstrated that age, SBP, WHR, GLU, TG and eGFR were significant predictors of albuminuria. A high level of abnormal/positive mALB/Cr was found in people undergoing physical examinations. Increased age, SBP, WHR, GLU, TG and decreased eGFR are major risk factors of abnormal mALB/Cr. mALB/Cr should be monitored, especially in the elderly and those with high-metabolic-syndrome.

Compression Ratio and Catalyst Aging Effects on Aqueous Ethanol Ignition (Year 2): Part 1. Compression Ratio Effects on Aqueous Ethanol Ignition

DOT National Transportation Integrated Search

2009-09-01

The lean burning of water ethanol blends has the potential to reduce NOx, CO, and HC emissions while reducing the ethanol fermentation production cost of distillation and dehydration. The torch style ignition produced by the catalytic igniter allows ...

Compression Ratio Ion Mobility Programming (CRIMP) Accumulation and Compression of Billions of Ions for Ion Mobility-Mass Spectrometry Using Traveling Waves in Structures for Lossless Ion Manipulations (SLIM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Liulin; Garimella, Sandilya V. B.; Hamid, Ahmed M.

We report on the implementation of a traveling wave (TW) based compression ratio ion mobility programming (CRIMP) approach within Structures for Lossless Ion Manipulations (SLIM) that enables both greatly enlarged trapped ion charge capacities and also their subsequent efficient compression for use in ion mobility (IM) separations. Ion accumulation is conducted in a long serpentine path TW SLIM region after which CRIMP allows the large ion populations to be ‘squeezed’. The compression process occurs at an interface between two SLIM regions, one operating conventionally and the second having an intermittently pausing or ‘stuttering’ TW, allowing the contents of multiple binsmore » of ions from the first region to be merged into a single bin in the second region. In this initial work stationary voltages in the second region were used to block ions from exiting the first (trapping) region, and the resumption of TWs in the second region allows ions to exit, and the population to also be compressed if CRIMP is applied. In our initial evaluation we show that the number of charges trapped for a 40 s accumulation period was ~5×109, more than two orders of magnitude greater than the previously reported charge capacity using an ion funnel trap. We also show that over 1×109 ions can be accumulated with high efficiency in the present device, and that the extent of subsequent compression is only limited by the space charge capacity of the trapping region. Lower compression ratios allow increased IM peak heights without significant loss of signal, while excessively large compression ratios can lead to ion losses and other artifacts. Importantly, we show that extended ion accumulation in conjunction with CRIMP and multiple passes provides the basis for a highly desirable combination of ultra-high sensitivity and ultra-high resolution IM separations using SLIM.« less

Intelligent bandwidth compression

NASA Astrophysics Data System (ADS)

Tseng, D. Y.; Bullock, B. L.; Olin, K. E.; Kandt, R. K.; Olsen, J. D.

1980-02-01

The feasibility of a 1000:1 bandwidth compression ratio for image transmission has been demonstrated using image-analysis algorithms and a rule-based controller. Such a high compression ratio was achieved by first analyzing scene content using auto-cueing and feature-extraction algorithms, and then transmitting only the pertinent information consistent with mission requirements. A rule-based controller directs the flow of analysis and performs priority allocations on the extracted scene content. The reconstructed bandwidth-compressed image consists of an edge map of the scene background, with primary and secondary target windows embedded in the edge map. The bandwidth-compressed images are updated at a basic rate of 1 frame per second, with the high-priority target window updated at 7.5 frames per second. The scene-analysis algorithms used in this system together with the adaptive priority controller are described. Results of simulated 1000:1 bandwidth-compressed images are presented.

Transformation of Mixed Contaminants of Trichloroethylene and Chromium using Polymer Modified and Unmodified KMnO4 Particles in Soil and Water Treatment

NASA Astrophysics Data System (ADS)

Ighere, Jude

Industrialization over the last century has positively impacted many aspects of our lives but at a cost. Soil and groundwater in thousands of sites are rendered contaminated due to detrimental storage and disposal practices thereby posing threat to sources of safe drinking water. In this research, the extent and kinetics of degradation of trichloroethylene (TCE) as a single contaminant in soil and water were investigated. Also, the reductive transformation of toxic hexavalent chromium, Cr (VI) to non-toxic trivalent, Cr (III) form was performed both in soil and aqueous system. The synergistic and antagonistic effect of associated with co-existing (TCE) and Cr (VI) was explored by simultaneous remediation in the same system. The extent and kinetics of trichloroethylene degradation by KMnO4 was mainly controlled by the molar ratio of KMnO4 to TCE. At molar ratios of 2:1 (stochiometric), 5:1, 10:1 of KMnO4 to TCE, 62.5%, 100%, and 100% of TCE were oxidized respectively in aqueous media. For different TCE concentrations below the solubility limit, the results were similar. In soil systems, the duration required for equilibrium degradation was longer with 62.8%, 96% and 100% conversions in a 3-day monitoring period. Under extreme pH conditions of 2.8 (acidic) and 12 (alkaline) in a stochiometric molar ratio, 63.75% and 59.75% yield was achieved in a 3-hour time to equilibrium. The reductive transformation of Cr (VI) to Cr (III) using ferrous ion (Fe2+) was a very fast reaction. The fast reduction reaction rate was accompanied by rapid precipitations of ferric ion and Cr (III). These precipitates ultimately quench or slow down the reaction. Under strong alkaline conditions, the degradation was slightly more effective. However, pH variation does not largely impact the overall extent of reaction at equilibrium. In soil, conversions of 73% and 91.9% were obtained at molar ratios of 1:10 and 1:15 of Cr (VI) to Fe(II) respectively in a 3-hour period. Since Cr (VI) is highly soluble in water, it does not form complexes strongly with soil organic matter. The result indicated that TCE oxidation by KMnO4 was not impacted by the presence of Cr (VI), but the reduction of Cr (VI) by ferrous ion was influenced greatly by the presence of TCE. The release profile for polymer modified KMnO4 in aqueous media indicated that the release efficiency was inversely proportional to the mass ratio of KMnO4 to PMMA particles. Application of encapsulated matrix in mixed contaminant treatment yielded 81% Cr (VI) reduction and 88% TCE oxidation by ferrous ion and modified permanganate respectively. PMMA improved interaction of KMnO4 particles with target contaminant (TCE) but with a low oxidant release rate.

Intelligent bandwith compression

NASA Astrophysics Data System (ADS)

Tseng, D. Y.; Bullock, B. L.; Olin, K. E.; Kandt, R. K.; Olsen, J. D.

1980-02-01

The feasibility of a 1000:1 bandwidth compression ratio for image transmission has been demonstrated using image-analysis algorithms and a rule-based controller. Such a high compression ratio was achieved by first analyzing scene content using auto-cueing and feature-extraction algorithms, and then transmitting only the pertinent information consistent with mission requirements. A rule-based controller directs the flow of analysis and performs priority allocations on the extracted scene content. The reconstructed bandwidth-compressed image consists of an edge map of the scene background, with primary and secondary target windows embedded in the edge map. The bandwidth-compressed images are updated at a basic rate of 1 frame per second, with the high-priority target window updated at 7.5 frames per second. The scene-analysis algorithms used in this system together with the adaptive priority controller are described. Results of simulated 1000:1 band width-compressed images are presented. A video tape simulation of the Intelligent Bandwidth Compression system has been produced using a sequence of video input from the data base.

Artificial Neural Network-Based Three-dimensional Continuous Response Relationship Construction of 3Cr20Ni10W2 Heat-Resisting Alloy and Its Application in Finite Element Simulation

NASA Astrophysics Data System (ADS)

Li, Le; Wang, Li-yong

2018-04-01

The application of accurate constitutive relationship in finite element simulation would significantly contribute to accurate simulation results, which plays a critical role in process design and optimization. In this investigation, the true stress-strain data of 3Cr20Ni10W2 heat-resisting alloy were obtained from a series of isothermal compression tests conducted in a wide temperature range of 1203-1403 K and strain rate range of 0.01-10 s-1 on a Gleeble 1500 testing machine. Then the constitutive relationship was modeled by an optimally constructed and well-trained back-propagation artificial neural network (BP-ANN). The evaluation of the BP-ANN model revealed that it has admirable performance in characterizing and predicting the flow behaviors of 3Cr20Ni10W2 heat-resisting alloy. Meanwhile, a comparison between improved Arrhenius-type constitutive equation and BP-ANN model shows that the latter has higher accuracy. Consequently, the developed BP-ANN model was used to predict abundant stress-strain data beyond the limited experimental conditions and construct the three-dimensional continuous response relationship for temperature, strain rate, strain, and stress. Finally, the three-dimensional continuous response relationship was applied to the numerical simulation of isothermal compression tests. The results show that such constitutive relationship can significantly promote the accuracy improvement of numerical simulation for hot forming processes.

Effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures

Treesearch

Andy W.C. Lee; Zhongli Hong; Douglas R. Phillips; Chung-Yun Hse

1987-01-01

This study investigated the effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures made from six wood species: southern pine, white oak, southern red oak, yellow-poplar, sweetgum, and hickory. Cement/wood ratios varied from 13/1 to 4/1. Wood storage conditions consisted of air-...

Improving transmission efficiency of large sequence alignment/map (SAM) files.

PubMed

Sakib, Muhammad Nazmus; Tang, Jijun; Zheng, W Jim; Huang, Chin-Tser

2011-01-01

Research in bioinformatics primarily involves collection and analysis of a large volume of genomic data. Naturally, it demands efficient storage and transfer of this huge amount of data. In recent years, some research has been done to find efficient compression algorithms to reduce the size of various sequencing data. One way to improve the transmission time of large files is to apply a maximum lossless compression on them. In this paper, we present SAMZIP, a specialized encoding scheme, for sequence alignment data in SAM (Sequence Alignment/Map) format, which improves the compression ratio of existing compression tools available. In order to achieve this, we exploit the prior knowledge of the file format and specifications. Our experimental results show that our encoding scheme improves compression ratio, thereby reducing overall transmission time significantly.

Turbulence intensity and spatial integral scale during compression and expansion strokes in a four-cycle reciprocating engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ikegami, M.; Shioji, M.; Nishimoto, K.

1987-01-01

A laser homodyne technique is applied to measure turbulence intensities and spatial scales during compression and expansion strokes in a non-fired engine. By using this technique, relative fluid motion in a turbulent flow is detected directly without cyclic variation biases caused by fluctuation in the main flow. Experiments are performed at different engine speeds, compression ratios, and induction swirl ratios. In no-swirl cases the turbulence field near the compression end is almost uniform, whereas in swirled cases both the turbulence intensity and the scale near the cylinder axis are higher than those in the periphery. In addition, based on themore » measured results, the k-epsilon two-equation turbulence model under the influence of compression is discussed.« less

The BCC/B2 morphologies in Al xNiCoFeCr high-entropy alloys

DOE PAGES

Ma, Yue; Jiang, Beibei; Li, Chunling; ...

2017-02-15

Here, the present work primarily investigates the morphological evolution of the body-centered-cubic (BCC)/B2 phases in Al xNiCoFeCr high-entropy alloys (HEAs) with increasing Al content. It is found that the BCC/B2 coherent morphology is closely related to the lattice misfit between these two phases, which is sensitive to Al. There are two types of microscopic BCC/B2 morphologies in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The mechanical properties,more » including the compressive yielding strength and microhardness of the Al xNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).« less

Extrusion-mixing compared with hand-mixing of polyether impression materials?

PubMed

McMahon, Caroline; Kinsella, Daniel; Fleming, Garry J P

2010-12-01

The hypotheses tested were two-fold (a) whether altering the base:catalyst ratio influences working time, elastic recovery and strain in compression properties of a hand-mixed polyether impression material and (b) whether an extrusion-mixed polyether impression material would have a significant advantage over a hand-mixed polyether impression material mixed to the optimum base:catalyst ratio. The polyether was hand-mixed at the optimum (manufacturers recommended) base:catalyst ratios (7:1) and further groups were made by increasing or decreasing the catalyst length by 25%. Additionally specimens were also made from an extrusion-mixed polyether impression material and compared with the optimum hand-mixed base:catalyst ratio. A penetrometer assembly was used to measure the working time (n=5). Five cylindrical specimens for each hand-mixed and extrusion mixed group investigated were employed for elastic recovery and strain in compression testing. Hand-mixing polyether impression materials with 25% more catalyst than that recommended significantly decreased the working time while hand-mixing with 25% less catalyst than that recommended significantly increased the strain in compression. The extrusion-mixed polyether impression material provided similar working time, elastic recovery and strain in compression to the hand-mixed polyether mixed at the optimum base:catalyst ratio.

Mathematical Model Relating Uniaxial Compressive Behavior of Manufactured Sand Mortar to MIP-Derived Pore Structure Parameters

PubMed Central

Tian, Zhenghong; Bu, Jingwu

2014-01-01

The uniaxial compression response of manufactured sand mortars proportioned using different water-cement ratio and sand-cement ratio is examined. Pore structure parameters such as porosity, threshold diameter, mean diameter, and total amounts of macropores, as well as shape and size of micropores are quantified by using mercury intrusion porosimetry (MIP) technique. Test results indicate that strains at peak stress and compressive strength decreased with the increasing sand-cement ratio due to insufficient binders to wrap up entire sand. A compression stress-strain model of normal concrete extending to predict the stress-strain relationships of manufactured sand mortar is verified and agreed well with experimental data. Furthermore, the stress-strain model constant is found to be influenced by threshold diameter, mean diameter, shape, and size of micropores. A mathematical model relating stress-strain model constants to the relevant pore structure parameters of manufactured sand mortar is developed. PMID:25133257

Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1993-01-01

Combined inplane compressive and shear buckling analysis was conducted on flat rectangular sandwich panels using the Raleigh-Ritz minimum energy method with a consideration of transverse shear effect of the sandwich core. The sandwich panels were fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that slightly slender (along unidirectional compressive loading axis) rectangular sandwich panels have the most desirable stiffness-to-weight ratios for aerospace structural applications; the degradation of buckling strength of sandwich panels with rising temperature is faster in shear than in compression; and the fiber orientation of the face sheets for optimum combined-load buckling strength of sandwich panels is a strong function of both loading condition and panel aspect ratio. Under the same specific weight and panel aspect ratio, a sandwich panel with metal matrix composite face sheets has much higher buckling strength than one having monolithic face sheets.

A Study on Homogeneous Charge Compression Ignition Gasoline Engines

NASA Astrophysics Data System (ADS)

Kaneko, Makoto; Morikawa, Koji; Itoh, Jin; Saishu, Youhei

A new engine concept consisting of HCCI combustion for low and midrange loads and spark ignition combustion for high loads was introduced. The timing of the intake valve closing was adjusted to alter the negative valve overlap and effective compression ratio to provide suitable HCCI conditions. The effect of mixture formation on auto-ignition was also investigated using a direct injection engine. As a result, HCCI combustion was achieved with a relatively low compression ratio when the intake air was heated by internal EGR. The resulting combustion was at a high thermal efficiency, comparable to that of modern diesel engines, and produced almost no NOx emissions or smoke. The mixture stratification increased the local A/F concentration, resulting in higher reactivity. A wide range of combustible A/F ratios was used to control the compression ignition timing. Photographs showed that the flame filled the entire chamber during combustion, reducing both emissions and fuel consumption.

Mathematical model relating uniaxial compressive behavior of manufactured sand mortar to MIP-derived pore structure parameters.

PubMed

Tian, Zhenghong; Bu, Jingwu

2014-01-01

The uniaxial compression response of manufactured sand mortars proportioned using different water-cement ratio and sand-cement ratio is examined. Pore structure parameters such as porosity, threshold diameter, mean diameter, and total amounts of macropores, as well as shape and size of micropores are quantified by using mercury intrusion porosimetry (MIP) technique. Test results indicate that strains at peak stress and compressive strength decreased with the increasing sand-cement ratio due to insufficient binders to wrap up entire sand. A compression stress-strain model of normal concrete extending to predict the stress-strain relationships of manufactured sand mortar is verified and agreed well with experimental data. Furthermore, the stress-strain model constant is found to be influenced by threshold diameter, mean diameter, shape, and size of micropores. A mathematical model relating stress-strain model constants to the relevant pore structure parameters of manufactured sand mortar is developed.

Shear Performance of Horizontal Joints in Short Precast Concrete Columns with Sleeve Grouted Connections under Cyclic Loading

PubMed Central

Liu, Bingyu; Chen, Jiang; Zhang, Yiping

2016-01-01

In this study, two short precast concrete columns and two cast-in-situ concrete columns were tested under cyclic loads. It was shown that the sleeve grouted connection was equivalent to the cast-in-situ connections for short columns when the axial compression ratio was 0.6. In order to determine the influence of the axial compression ratio and the shear-span ratio on the shear capacity of the horizontal joint, a FE model was established and verified. The analysis showed that the axial compression ratio is advantageous to the joint and the shear capacity of the horizontal joint increases with increase of the shear-span ratio. Based on the results, the methods used to estimate the shear capacity of horizontal joints in the Chinese Specification and the Japanese Guidelines are discussed and it was found that both overestimated the shear capacity of the horizontal joint. In addition, the Chinese Specification failed to consider the influence of the shear-span ratio. PMID:27861493

Magnetic resonance spectroscopy in mild cognitive impairment: systematic review and meta-analysis.

PubMed

Tumati, Shankar; Martens, Sander; Aleman, André

2013-12-01

Research using proton magnetic resonance spectroscopy (MRS) can potentially elucidate metabolite changes representing early degeneration in Mild Cognitive Impairment (MCI), an early stage of dementia. We integrated the published literature using meta-analysis to identify patterns of metabolite changes in MCI. 29 MRS studies (with a total of 607 MCI patients and 862 healthy controls) were classified according to brain regions. Hedges' g was used as effect size in a random effects model. N-Acetyl Aspartate (NAA) measures were consistently reduced in posterior cingulate (PC), hippocampus, and the paratrigonal white matter (PWM). Creatine (Cr) concentration was reduced in the hippocampus and PWM. Choline (Cho) concentration was reduced in the hippocampus while Cho/Cr ratio was raised in the PC. Myo-inositol (mI) concentration was raised in the PC and mI/Cr ratio was raised in the hippocampus. NAA/mI ratio was reduced in the PC. NAA may be the most reliable marker of brain dysfunction in MCI though mI, Cho, and Cr may also contribute towards this. Copyright © 2013 Elsevier Ltd. All rights reserved.

High-precision QEC values of superallowed 0+ → 0+β-emitters 46Cr, 50Fe and 54Ni

NASA Astrophysics Data System (ADS)

Zhang, P.; Xu, X.; Shuai, P.; Chen, R. J.; Yan, X. L.; Zhang, Y. H.; Wang, M.; Litvinov, Yu. A.; Blaum, K.; Xu, H. S.; Bao, T.; Chen, X. C.; Chen, H.; Fu, C. Y.; He, J. J.; Kubono, S.; Lam, Y. H.; Liu, D. W.; Mao, R. S.; Ma, X. W.; Sun, M. Z.; Tu, X. L.; Xing, Y. M.; Yang, J. C.; Yuan, Y. J.; Zeng, Q.; Zhou, X.; Zhou, X. H.; Zhan, W. L.; Litvinov, S.; Audi, G.; Uesaka, T.; Yamaguchi, Y.; Yamaguchi, T.; Ozawa, A.; Sun, B. H.; Sun, Y.; Xu, F. R.

2017-04-01

Short-lived 46Cr, 50Fe and 54Ni were studied by isochronous mass spectrometry at the HIRFL-CSR facility in Lanzhou. The measured precision mass excesses (ME) of 46Cr, 50Fe and 54Ni are - 29471 (11) keV, - 34477 (6) keV and - 39278 (4) keV, respectively. The superallowed 0+ →0+β-decay Q values were derived to be QEC (46Cr) = 7604 (11) keV, QEC (50Fe) = 8150 (6) keV and QEC (54Ni) = 8731 (4) keV. The values for 50Fe and 54Ni are by one order of magnitude more precise than the adopted literature values. By combining the existing half-lives and branching ratios, we obtained the corrected Ft values to be Ft (50Fe) = 3103 (70) s and Ft (54Ni) = 3076 (50) s. The main contribution to the Ft uncertainties is now due to β-decay branching ratios, still, more high-precision measurements of the half-lives, the masses, and especially the branching ratios are needed in order to satisfy the requirements for a stringent CVC test.

Synthesis of Bi nanowire networks and their superior photocatalytic activity for Cr(vi) reduction.

PubMed

Zhao, Jin; Han, Qiaofeng; Zhu, Junwu; Wu, Xiaodong; Wang, Xin

2014-09-07

Interconnected Bi nanowire networks were synthesized for the first time via a solvothermal route by using ethylene glycol (EG) as both a solvent and a reducing agent, and citric acid (CA) as a stabilizing agent at a molar ratio of CA/Bi(3+) = 5. Among various reaction conditions including the temperature, reaction time and precursor concentration, the molar ratio of CA/Bi(3+) was the dominant experimental parameter to influence the morphology and structures of the Bi crystals. Highly dispersed Bi microspheres and network-like Bi thick wires were obtained if the molar ratio of CA/Bi(3+) was changed to 2.5 and 10, respectively. As compared to other additives including trisodium citrate, cetyltrimethylammonium bromide (CTAB) and oxalic acid, good solubility of CA in EG together with its coordination effect played a crucial role in the formation of network-like Bi nanowires. The Bi nanowire networks exhibited excellent photocatalytic performance for Cr(vi) reduction. Cr(vi) was completely reduced to less toxic Cr(iii) after 8 min and 55 min of UV and visible-light irradiation, respectively.

Pressure effects on structural, electronic, elastic and lattice dynamical properties of XSi2 (X = Cr, Mo, W) from first principles

NASA Astrophysics Data System (ADS)

Zhu, Haiyan; Shi, Liwei; Li, Shuaiqi; Zhang, Shaobo; Xia, Wangsuo

2018-04-01

First-principles calculations have been performed to study the structure, elastic and lattice dynamical properties of C40 XSi2 (X=Cr, Mo, W) under hydrostatic pressure. The obtained structural parameters are in line with existing experimental and theoretical data. The evolutions of fundamental bandgap energies, elastic moduli, IR absorption spectra with pressure have been investigated in detail. Our results indicate that the energy gaps of XSi2 (X=Cr, Mo, W) show different trends as the pressure increases. Larger BH/GH ratio and Poisson’s ratio are achieved with pressure, suggesting an improved ductility for XSi2 (X=Cr, Mo, W). Moreover, a large elastic anisotropy under pressure is exhibited in Young’s anisotropic factors. The infrared-active phonon frequencies exhibit substantial blueshifts under pressure.

Single voxel magnetic resonance spectroscopy at 3 Tesla in a memory disorders clinic: early right hippocampal NAA/Cr loss in mildly impaired subjects.

PubMed

Caserta, Maria T; Ragin, Ann; Hermida, Adriana P; Ahrens, R John; Wise, Leon

2008-11-30

In this study, we use magnetic resonance spectroscopy (MRS) at 3 Tesla to measure N-acetyl aspartate (NAA), myo-inositol (mI) and choline (Cho) to creatine (Cr) ratios in R (right) and L (left) hippocampi (H) in 8 mildly memory impaired (MMI), 6 probable Alzheimer's Disease (PRAD), and 17 control subjects. NAA/Cr was significantly reduced in the RH in the MMI group and bilaterally in the PRAD group vs. controls. No other metabolite differences were noted between the three groups. Five MMI subjects have converted to PRAD in follow-up. These findings suggest that RH NAA/Cr ratios measured at 3 Tesla may be a sensitive marker of future progression to dementia in a clinically defined population with isolated memory complaints.

Microstructure and corrosion behaviour in biological environments of the new forged low-Ni Co-Cr-Mo alloys.

PubMed

Hiromoto, Sachiko; Onodera, Emi; Chiba, Akihiko; Asami, Katsuhiko; Hanawa, Takao

2005-08-01

Corrosion behaviour and microstructure of developed low-Ni Co-29Cr-(6, 8)Mo (mass%) alloys and a conventional Co-29Cr-6Mo-1Ni alloy (ASTM F75-92) were investigated in saline solution (saline), Hanks' solution (Hanks), and cell culture medium (E-MEM + FBS). The forging ratios of the Co-29Cr-6Mo alloy were 50% and 88% and that of the Co-29Cr-8Mo alloy was 88%. Ni content in the air-formed surface oxide film of the low-Ni alloys was under the detection limit of XPS. The passive current densities of the low-Ni alloys were of the same order of magnitude as that of the ASTM alloy in all the solutions. The passive current densities of all the alloys did not significantly change with the inorganic ions and the biomolecules. The anodic current densities in the secondary passive region of the low-Ni alloys were lower than that of the ASTM alloy in the E-MEM + FBS. Consequently, the low-Ni alloys are expected to show as high corrosion resistance as the ASTM alloy. On the other hand, the passive current density of the Co-29Cr-6Mo alloy with a forging ratio of 50% was slightly lower than that with a forging ratio of 88% in the saline. The refining of grains by further forging causes the increase in the passive current density of the low-Ni alloy.

Evaluating metabolites in patients with major depressive disorder who received mindfulness-based cognitive therapy and healthy controls using short echo MRSI at 7 Tesla.

PubMed

Li, Yan; Jakary, Angela; Gillung, Erin; Eisendrath, Stuart; Nelson, Sarah J; Mukherjee, Pratik; Luks, Tracy

2016-06-01

Our aim was to evaluate differences in metabolite levels between unmedicated patients with major depressive disorder (MDD) and healthy controls, to assess changes in metabolites in patients after they completed an 8-week course of mindfulness-based cognitive therapy (MBCT), and to exam the correlation between metabolites and depression severity. Sixteen patients with MDD and ten age- and gender-matched healthy controls were studied using 3D short echo-time (20 ms) magnetic resonance spectroscopic imaging (MRSI) at 7 Tesla. Relative metabolite ratios were estimated in five regions of interest corresponding to insula, anterior cingulate cortex (ACC), caudate, putamen, and thalamus. In all cases, MBCT reduced severity of depression. The ratio of total choline-containing compounds/total creatine (tCr) in the right caudate was significantly increased compared to that in healthy controls, while ratios of N-acetyl aspartate (NAA)/tCr in the left ACC, myo-inositol/tCr in the right insula, and glutathione/tCr in the left putamen were significantly decreased. At baseline, the severity of depression was negatively correlated with my-inositol/tCr in the left insula and putamen. The improvement in depression severity was significantly associated with changes in NAA/tCr in the left ACC. This study has successfully evaluated regional differences in metabolites for patients with MDD who received MBCT treatment and in controls using 7 Tesla MRSI.

Evaluation of the normal-to-diseased apparent diffusion coefficient ratio as an indicator of prostate cancer aggressiveness.

PubMed

Lebovici, Andrei; Sfrangeu, Silviu A; Feier, Diana; Caraiani, Cosmin; Lucan, Ciprian; Suciu, Mihai; Elec, Florin; Iacob, Gheorghita; Buruian, Mircea

2014-05-10

We tested the feasibility of a simple method for assessment of prostate cancer (PCa) aggressiveness using diffusion-weighted magnetic resonance imaging (MRI) to calculate apparent diffusion coefficient (ADC) ratios between prostate cancer and healthy prostatic tissue. The requirement for institutional review board approval was waived. A set of 20 standardized core transperineal saturation biopsy specimens served as the reference standard for placement of regions of interest on ADC maps in tumorous and normal prostatic tissue of 22 men with PCa (median Gleason score: 7; range, 6-9). A total of 128 positive sectors were included for evaluation. Two diagnostic ratios were computed between tumor ADCs and normal sector ADCs: the ADC peripheral ratio (the ratio between tumor ADC and normal peripheral zone tissue, ADC-PR), and the ADC central ratio (the ratio between tumor ADC and normal central zone tissue, ADC-CR). The performance of the two ratios in detecting high-risk tumor foci (Gleason 8 and 9) was assessed using the area under the receiver operating characteristic curve (AUC). Both ADC ratios presented significantly lower values in high-risk tumors (0.48 ± 0.13 for ADC-CR and 0.40 ± 0.09 for ADC-PR) compared with low-risk tumors (0.66 ± 0.17 for ADC-CR and 0.54 ± 0.09 for ADC-PR) (p < 0.001) and had better diagnostic performance (ADC-CR AUC = 0.77, sensitivity = 82.2%, specificity = 66.7% and ADC-PR AUC = 0.90, sensitivity = 93.7%, specificity = 80%) than stand-alone tumor ADCs (AUC of 0.75, sensitivity = 72.7%, specificity = 70.6%) for identifying high-risk lesions. The ADC ratio as an intrapatient-normalized diagnostic tool may be better in detecting high-grade lesions compared with analysis based on tumor ADCs alone, and may reduce the rate of biopsies.

Evaluation of the normal-to-diseased apparent diffusion coefficient ratio as an indicator of prostate cancer aggressiveness

PubMed Central

2014-01-01

Background We tested the feasibility of a simple method for assessment of prostate cancer (PCa) aggressiveness using diffusion-weighted magnetic resonance imaging (MRI) to calculate apparent diffusion coefficient (ADC) ratios between prostate cancer and healthy prostatic tissue. Methods The requirement for institutional review board approval was waived. A set of 20 standardized core transperineal saturation biopsy specimens served as the reference standard for placement of regions of interest on ADC maps in tumorous and normal prostatic tissue of 22 men with PCa (median Gleason score: 7; range, 6–9). A total of 128 positive sectors were included for evaluation. Two diagnostic ratios were computed between tumor ADCs and normal sector ADCs: the ADC peripheral ratio (the ratio between tumor ADC and normal peripheral zone tissue, ADC-PR), and the ADC central ratio (the ratio between tumor ADC and normal central zone tissue, ADC-CR). The performance of the two ratios in detecting high-risk tumor foci (Gleason 8 and 9) was assessed using the area under the receiver operating characteristic curve (AUC). Results Both ADC ratios presented significantly lower values in high-risk tumors (0.48 ± 0.13 for ADC-CR and 0.40 ± 0.09 for ADC-PR) compared with low-risk tumors (0.66 ± 0.17 for ADC-CR and 0.54 ± 0.09 for ADC-PR) (p < 0.001) and had better diagnostic performance (ADC-CR AUC = 0.77, sensitivity = 82.2%, specificity = 66.7% and ADC-PR AUC = 0.90, sensitivity = 93.7%, specificity = 80%) than stand-alone tumor ADCs (AUC of 0.75, sensitivity = 72.7%, specificity = 70.6%) for identifying high-risk lesions. Conclusions The ADC ratio as an intrapatient-normalized diagnostic tool may be better in detecting high-grade lesions compared with analysis based on tumor ADCs alone, and may reduce the rate of biopsies. PMID:24885552

Effects of hyperglycemia and effects of ketosis on cerebral perfusion, cerebral water distribution, and cerebral metabolism.

PubMed

Glaser, Nicole; Ngo, Catherine; Anderson, Steven; Yuen, Natalie; Trifu, Alexandra; O'Donnell, Martha

2012-07-01

Diabetic ketoacidosis (DKA) may cause brain injuries in children. The mechanisms responsible are difficult to elucidate because DKA involves multiple metabolic derangements. We aimed to determine the independent effects of hyperglycemia and ketosis on cerebral metabolism, blood flow, and water distribution. We used magnetic resonance spectroscopy to measure ratios of cerebral metabolites (ATP to inorganic phosphate [Pi], phosphocreatine [PCr] to Pi, N-acetyl aspartate [NAA] to creatine [Cr], and lactate to Cr) and diffusion-weighted imaging and perfusion-weighted imaging to assess cerebral water distribution (apparent diffusion coefficient [ADC] values) and cerebral blood flow (CBF) in three groups of juvenile rats (hyperglycemic, ketotic, and normal control). ATP-to-Pi ratio was reduced in both hyperglycemic and ketotic rats in comparison with controls. PCr-to-Pi ratio was reduced in the ketotic group, and there was a trend toward reduction in the hyperglycemic group. No significant differences were observed in NAA-to-Cr or lactate-to-Cr ratio. Cortical ADC was reduced in both groups (indicating brain cell swelling). Cortical CBF was also reduced in both groups. We conclude that both hyperglycemia and ketosis independently cause reductions in cerebral high-energy phosphates, CBF, and cortical ADC values. These effects may play a role in the pathophysiology of DKA-related brain injury.

Synthesis and Characterization of Allophane-Like as Chromium (Cr) Ion Adsorbent

NASA Astrophysics Data System (ADS)

Pranoto; Purnawan, C.; Husnina, A. N.

2018-03-01

The synthesis and characterization of allophane-like as chrom (Cr) ion adsorbent has been studied. The objectives of this study is to determine the characteristics of allophane-like and determine ratio of Al/Si, chromium solution pH, and contact time to get the best decreasing metal ion chrom (Cr) adsorption condition. The study was conducted with the ratio of Al/Si ratios 0.5; 0.75; 1.0; 1.25 and 1.5 from Tetraetyl Orthosilicate (TEOS) solution and Aluminium Nitrate Nonahydrate [Al(NO3)3.9H2O] in pH 3-4. The result of synthetic was characterized on functional groups and cristallinity. Experiment of adsorption ability using variation of Cr solution pH 3-7, contact time 30, 60, 90 and 120 minutes with batch method. The results by FTIR shows that functional groups-OH, the asymmetry groups O-Si-O or O-Al-O, relatively weak absorption which stronger then the presence of OH and bending vibration Si-O or Al-O on allophane-like. The best conditions of chromium metal adsorption with adsorbent allophane-like was obtained at pH 5, contact time 90 minutes, and the ratio Al/Si 1.5. Types of adsorption in this study follows Freundlich and Langmuir isotherm.

Effect of citric acid on material properties of ZnGa2O4:Cr3+ nanopowder prepared by sol-gel method

NASA Astrophysics Data System (ADS)

Hussen, Megersa K.; Dejene, Francis B.; Gonfa, Girma G.

2018-05-01

This paper reports the material properties of Cr3+ (1.0 mol%)-doped ZnGa2O4 nanopowders prepared by citric acid-assisted sol-gel method with metal cations (Zn + Ga) to citric (M:CA) molar ratios of (1:0.5, 1:1, 1:3 and 1:4). The X-ray diffraction (XRD) results show that the synthesized nanoparticles are cubic structured and concentration of citric acid did not affect the structure. The scanning electron microscope (SEM) shows that the increase of the M:CA molar ratio favors the formation of smaller nano particle of ZnGa2O4:Cr3+. The photoluminescence (PL) is found to be maximum for sample with M:CA ratio of 1:1. Further increase in citric acid leads to significant decrease in the PL intensity. Energy-dispersive X-ray spectroscopy (EDS) measurement confirms the presence of the Zn, Ga, O and Cr ions. Ultraviolet-visible (UV-Vis) spectrophotometer measurement shows an increase in reflectance in visible region and the energy band gap was found to decrease with an increase in citric acid molar ratio. The emission spectra, particle size and photoluminescence lifetimes are comparable with reports on bioimaging applications.

The Curious Case of High-energy Deuterons in Galactic Cosmic Rays

NASA Astrophysics Data System (ADS)

Tomassetti, Nicola; Feng, Jie

2017-02-01

A new analysis of cosmic ray (CR) data collected by the SOKOL experiment in space found that the deuteron-to-helium ratio at energies between 500 and 2000 GeV/nucleon takes the value d/He ˜ 1.5. As we will show, this result cannot be explained by standard models of secondary CR production in the interstellar medium and points to the existence of a high-energy source of CR deuterons. To account for the deuteron excess in CRs, we argue that the only viable solution is hadronic interaction processes of accelerated particles inside old supernova remnants (SNRs). From this mechanism, however, the B/C ratio is also expected to increase at energies above ˜50 of GeV/nucleon, in conflict with new precision data just released by the AMS-02 experiment. Hence, if this phenomenon is a real physical effect, hadronic production of CR deuterons must occur in SNRs characterized by low metal abundance. In such a scenario, the sources accelerating C-{N}-O nuclei are not the same as those accelerating helium or protons, so that the connection between d/He ratio and B/C ratio is broken, and the latter cannot be used to place constraints on the production of light isotopes or antiparticles.

The Characteristics and Generating Mechanism of Large Precipitates in Ti-Containing H13 Tool Steel

NASA Astrophysics Data System (ADS)

Xie, You; Cheng, Guoguang; Chen, Lie; Zhang, Yandong; Yan, Qingzhong

2017-02-01

The characteristics of large precipitates in H13 tool steel with 0.015wt% Ti were studied. The result shows that three types of phases larger than 1 μm exist in the as-cast ingot, that is, (Ti, V) (C, N) type phase, (V, Mo, Cr)C type phase and sulfide. (Ti, V) (C, N) type phase could be further classified as the homogeneous Ti-rich one and the Ti-V-rich one in which Ti/V ratio gradually changes. (V, Mo, Cr)C type phase contains the V-rich one and the Mo-Cr-rich one. The compositional characteristics in all of them have little relation with the cutting position or cooling rate. The precipitating process could be well described through calculation by Thermo-Calc software. During solidification, the primary phase (Ti, V)(C, N) first starts to precipitate in the form of Ti-rich carbonitride. With the development of solidification, the ratio of Ti decreases and that of V increases. Then the primary phase Ti-V-rich (Ti, V)(C, N) and V-rich (V, Mo, Cr)C appears successively. Mo-Cr-rich (V, Mo, Cr)C phase does not precipitate until the solidification process reaches to the end. Sulfide precipitates before (V, Mo, Cr)C type phase and it could act as the nucleus of (V, Mo, Cr)C.

Finite Element Simulation and X-Ray Microdiffraction Study of Strain Partitioning in a Layered Nanocomposite

DOE PAGES

Barabash, R. I.; Agarwal, V.; Koric, S.; ...

2016-01-01

Tmore » he depth-dependent strain partitioning across the interfaces in the growth direction of the NiAl/Cr(Mo) nanocomposite between the Cr and NiAl lamellae was directly measured experimentally and simulated using a finite element method (FEM). Depth-resolved X-ray microdiffraction demonstrated that in the as-grown state both Cr and NiAl lamellae grow along the 111 direction with the formation of as-grown distinct residual ~0.16% compressive strains for Cr lamellae and ~0.05% tensile strains for NiAl lamellae. hree-dimensional simulations were carried out using an implicit FEM. First simulation was designed to study residual strains in the composite due to cooling resulting in formation of crystals. Strains in the growth direction were computed and compared to those obtained from the microdiffraction experiments. Second simulation was conducted to understand the combined strains resulting from cooling and mechanical indentation of the composite. Numerical results in the growth direction of crystal were compared to experimental results confirming the experimentally observed trends.« less

Microscopy of Alloy Formation on Arc Plasma Sintered Oxide Dispersion Strengthen (ODS) Steel

NASA Astrophysics Data System (ADS)

Bandriyana, B.; Sujatno, A.; Salam, R.; Dimyati, A.; Untoro, P.

2017-07-01

The oxide dispersed strengthened (ODS) alloys steel developed as structure material for nuclear power plants (NPP) has good resistant against creep due to their unique microstructure. Microscopy investigation on the microstructure formation during alloying process especially at the early stages was carried out to study the correlation between structure and property of ODS alloys. This was possible thanks to the arc plasma sintering (APS) device which can simulate the time dependent alloying processes. The ODS sample with composition of 88 wt.% Fe and 12 wt.% Cr powder dispersed with 1 wt.% ZrO2 nano powder was mixed in a high energy milling, isostatic compressed to form sample coins and then alloyed in APS. The Scanning Electron Microscope (SEM) with X-ray Diffraction Spectroscopy (EDX) line scan and mapping was used to characterize the microstructure and elemental composition distribution of the samples. The alloying process with unification of each Fe and Cr phase continued by the alloying formation of Fe-Cr by inter-diffusion of both Fe and Cr and followed by the improvement of the mechanical properties of hardness.

Formulation and dissolution kinetics study of hydrophilic matrix tablets with tramadol hydrochloride and different co-processed dry binders.

PubMed

Komersová, Alena; Lochař, Václav; Myslíková, Kateřina; Mužíková, Jitka; Bartoš, Martin

2016-12-01

The aim of this study is to present the possibility of using of co-processed dry binders for formulation of matrix tablets with drug controlled release. Hydrophilic matrix tablets with tramadol hydrochloride, hypromellose and different co-processed dry binders were prepared by direct compression method. Hypromelloses Methocel™ K4M Premium CR or Methocel™ K100M Premium CR were used as controlled release agents and Prosolv® SMCC 90 or Disintequik™ MCC 25 were used as co-processed dry binders. Homogeneity of the tablets was evaluated using scanning electron microscopy and energy dispersive X-ray microanalysis. The release of tramadol hydrochloride from prepared formulations was studied by dissolution test method. The dissolution profiles obtained were evaluated by non-linear regression analysis, release rate constants and other kinetic parameters were determined. It was found that matrix tablets based on Prosolv® SMCC 90 and Methocel™ Premium CR cannot control the tramadol release effectively for >12h and tablets containing Disintequik™ MCC 25 and Methocel™ Premium CR >8h. Copyright © 2016 Elsevier B.V. All rights reserved.

Towards the damage evaluation using Gurson-Tvergaard-Needleman (GTN) model for hot forming processes

NASA Astrophysics Data System (ADS)

Imran, Muhammad; Bambach, Markus

2018-05-01

In the production of semi-finished metal products, hot forming is used to eliminate the pores and voids from the casting process under compressive stresses and to modify the microstructure for further processing. In the case of caliber and flat rolling processes, tensile stresses occur at certain roll gap ratios which promote pore formation on nonmetallic inclusion. The formation of new pores contributes to ductile damage and reduces the load carrying capacity of the material. In the literature, the damage nucleation and growth during the hot forming process are not comprehensively described. The aim of this study is to understand the damage initiation and growth mechanism during hot forming processes. Hot tensile tests are performed at different temperatures and strain rates for 16MnCrS5 steel. To investigate the influence of geometrical variations on the damage mechanism, specimens with different stress triaxiality ratios are used. Finite element simulations using the Gurson-Tvergaard-Needleman (GTN) damage model are performed to estimate the critical void fraction for the damage initiation and the evolution of the void volume fraction. The results showed that the GTN model underestimates the softening of the material due to the independence of the temperature and the strain rate.

Measuring the lactate-to-creatine ratio via 1H NMR spectroscopy can be used to noninvasively evaluate apoptosis in glioma cells after X-ray irradiation.

PubMed

Li, Hongxia; Cui, Yi; Li, Fuyan; Shi, Wenqi; Gao, Wenjing; Wang, Xiao; Zeng, Qingshi

2018-01-01

Radiotherapy is among the commonly applied treatment options for glioma, which is one of the most common types of primary brain tumor. To evaluate the effect of radiotherapy noninvasively, it is vital for oncologists to monitor the effects of X-ray irradiation on glioma cells. Preliminary research had showed that PKC-ι expression correlates with tumor cell apoptosis induced by X-ray irradiation. It is also believed that the lactate-to-creatine (Lac/Cr) ratio can be used as a biomarker to evaluate apoptosis in glioma cells after X-ray irradiation. In this study, we evaluated the relationships between the Lac/Cr ratio, apoptotic rate, and protein kinase C iota (PKC-ι) expression in glioma cells. Cells of the glioma cell lines C6 and U251 were randomly divided into 4 groups, with every group exposed to X-ray irradiation at 0, 1, 5, 10 and 15 Gy. Single cell gel electrophoresis (SCGE) was conducted to evaluate the DNA damage. Flow cytometry was performed to measure the cell cycle blockage and apoptotic rates. Western blot analysis was used to detect the phosphorylated PKC-ι (p-PKC-ι) level. 1 H NMR spectroscopy was employed to determine the Lac/Cr ratio. The DNA damage increased in a radiation dose-dependent manner ( p  < 0.05). With the increase in X-ray irradiation, the apoptotic rate also increased (C6, p  < 0.01; U251, p  < 0.05), and the p-PKC-ι level decreased (C6, p  < 0.01; U251, p  < 0.05). The p-PKC-ι level negatively correlated with apoptosis, whereas the Lac/Cr ratio positively correlated with the p-PKC-ι level. The Lac/Cr ratio decreases with an increase in X-ray irradiation and thus can be used as a biomarker to reflect the effects of X-ray irradiation in glioma cells.

Poisson's Ratio of a Hyperelastic Foam Under Quasi-static and Dynamic Loading

DOE PAGES

Sanborn, Brett; Song, Bo

2018-06-03

Poisson's ratio is a material constant representing compressibility of material volume. However, when soft, hyperelastic materials such as silicone foam are subjected to large deformation into densification, the Poisson's ratio may rather significantly change, which warrants careful consideration in modeling and simulation of impact/shock mitigation scenarios where foams are used as isolators. The evolution of Poisson's ratio of silicone foam materials has not yet been characterized, particularly under dynamic loading. In this study, radial and axial measurements of specimen strain are conducted simultaneously during quasi-static and dynamic compression tests to determine the Poisson's ratio of silicone foam. The Poisson's ratiomore » of silicone foam exhibited a transition from compressible to nearly incompressible at a threshold strain that coincided with the onset of densification in the material. Poisson's ratio as a function of engineering strain was different at quasi-static and dynamic rates. Here, the Poisson's ratio behavior is presented and can be used to improve constitutive modeling of silicone foams subjected to a broad range of mechanical loading.« less

Poisson's Ratio of a Hyperelastic Foam Under Quasi-static and Dynamic Loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanborn, Brett; Song, Bo

Poisson's ratio is a material constant representing compressibility of material volume. However, when soft, hyperelastic materials such as silicone foam are subjected to large deformation into densification, the Poisson's ratio may rather significantly change, which warrants careful consideration in modeling and simulation of impact/shock mitigation scenarios where foams are used as isolators. The evolution of Poisson's ratio of silicone foam materials has not yet been characterized, particularly under dynamic loading. In this study, radial and axial measurements of specimen strain are conducted simultaneously during quasi-static and dynamic compression tests to determine the Poisson's ratio of silicone foam. The Poisson's ratiomore » of silicone foam exhibited a transition from compressible to nearly incompressible at a threshold strain that coincided with the onset of densification in the material. Poisson's ratio as a function of engineering strain was different at quasi-static and dynamic rates. Here, the Poisson's ratio behavior is presented and can be used to improve constitutive modeling of silicone foams subjected to a broad range of mechanical loading.« less

Transition-metal alloying of γ'-Ni3Al : Effects on the ideal uniaxial compressive strength from first-principles calculations

NASA Astrophysics Data System (ADS)

Wen, Minru; Wang, Chong-Yu

2018-01-01

The addition of transition-metal (TM) elements into the γ' precipitate phase of a Ni-based single-crystal superalloy can significantly affect its mechanical properties, including the intrinsic mechanical property of compressive strength. Using first-principles density functional calculations, the effects of 3 d (Sc-Zn), 4 d (Y-Cd), and 5 d (Hf-Au) TM alloying elements on the ideal uniaxial compressive strength of γ'-Ni3Al were investigated. The stress-strain relationships of pure Ni3Al under [100], [110], and [111] compressive loads and the site occupancy behavior of TM elements in Ni3Al were previously studied using a total-energy method based on density functional theory. Our results showed that the capacity of TM elements for strengthening the ideal compressive strength was associated with the d -electron number. The alloying elements with half-filled d bands (i.e., Cr, Mo, W, Tc, and Re) manifested the greatest efficacy for improving the ideal strength of Ni3Al under a deformation along the weakest compressive direction. Furthermore, the charge redistribution of Ni3Al doped with 5 d elements were also analyzed to understand the strengthening mechanisms of TM elements in the γ'-Ni3Al phase.

Wavelet-based Encoding Scheme for Controlling Size of Compressed ECG Segments in Telecardiology Systems.

PubMed

Al-Busaidi, Asiya M; Khriji, Lazhar; Touati, Farid; Rasid, Mohd Fadlee; Mnaouer, Adel Ben

2017-09-12

One of the major issues in time-critical medical applications using wireless technology is the size of the payload packet, which is generally designed to be very small to improve the transmission process. Using small packets to transmit continuous ECG data is still costly. Thus, data compression is commonly used to reduce the huge amount of ECG data transmitted through telecardiology devices. In this paper, a new ECG compression scheme is introduced to ensure that the compressed ECG segments fit into the available limited payload packets, while maintaining a fixed CR to preserve the diagnostic information. The scheme automatically divides the ECG block into segments, while maintaining other compression parameters fixed. This scheme adopts discrete wavelet transform (DWT) method to decompose the ECG data, bit-field preserving (BFP) method to preserve the quality of the DWT coefficients, and a modified running-length encoding (RLE) scheme to encode the coefficients. The proposed dynamic compression scheme showed promising results with a percentage packet reduction (PR) of about 85.39% at low percentage root-mean square difference (PRD) values, less than 1%. ECG records from MIT-BIH Arrhythmia Database were used to test the proposed method. The simulation results showed promising performance that satisfies the needs of portable telecardiology systems, like the limited payload size and low power consumption.

Influence of trimethylsilane flow on the microstructure, mechanical and tribological properties of CrSiCN coatings in water lubrication

NASA Astrophysics Data System (ADS)

Wu, Zhiwei; Zhou, Fei; Wang, Qianzhi; Zhou, Zhifeng; Yan, Jiwang; Li, Lawrence Kwok-Yan

2015-11-01

CrSiCN coatings with different silicon and carbon contents were deposited on silicon wafers and 316L stainless steels using unbalanced magnetron sputtering via adjusting trimethylsilane (TMS) flow, and their microstructure and mechanical properties were characterized by X-ray diffraction (XRD), scanning electron microscopy(SEM), X-ray photoelectrons spectroscopy(XPS) and nano-indenter, respectively. The tribological properties of CrSiCN coatings sliding against SiC balls in water were investigated using ball-on-disk tribometer. The results showed that the CrSiCN coatings had fine composite microstructure consisting of nanocrystallites of Cr(C, N) crystal and amorphous phases such as a-Si3N4 and a-C(a-CNx). The typical columnar structures changed from fine cluster to coarse ones when the Si content was beyond 3.4 at.%. With an increase in the TMS flow, the hardness and Young's modulus of Corsican coatings all first increased, and then rapidly decreased, but the compressive stress in the coatings varied in the range of 2.8-4.8 GPa. When the TMS flow was 10 sccm, the CrSiCN coatings exhibited the highest hardness of 21.3 GPa and the lowest friction coefficient (0.11) and wear rate (8.4 × 10-8 mm3/N m). But when the TMS flow was beyond 15 sccm, the tribological properties of CrSiCN coatings in water became poor.

Development of an imaging-planning program for screen/film and computed radiography mammography for breasts with short chest wall to nipple distance.

PubMed

Dong, S L; Su, J L; Yeh, Y H; Chu, T C; Lin, Y C; Chuang, K S

2011-04-01

Imaging breasts with a short chest wall to nipple distance (CWND) using a traditional mammographic X-ray unit is a technical challenge for mammographers. The purpose of this study is the development of an imaging-planning program to assist in determination of imaging parameters of screen/film (SF) and computed radiography (CR) mammography for short CWND breasts. A traditional mammographic X-ray unit (Mammomat 3000, Siemens, Munich, Germany) was employed. The imaging-planning program was developed by combining the compressed breast thickness correction, the equivalent polymethylmethacrylate thickness assessment for breasts and the tube loading (mAs) measurement. Both phantom exposures and a total of 597 exposures were used for examining the imaging-planning program. Results of the phantom study show that the tube loading rapidly decreased with the CWND when the automatic exposure control (AEC) detector was not fully covered by the phantom. For patient exposures with the AEC fully covered by breast tissue, the average fractional tube loadings, defined as the ratio of the predicted mAs using the imaging-planning program and mAs of the mammogram, were 1.10 and 1.07 for SF and CR mammograms, respectively. The predicted mAs values were comparable to the mAs values, as determined by the AEC. By applying the imaging-planning program in clinical practice, the experiential dependence of the mammographer for determination of the imaging parameters for short CWND breasts is minimised.

Progressive low-bitrate digital color/monochrome image coding by neuro-fuzzy clustering

NASA Astrophysics Data System (ADS)

Mitra, Sunanda; Meadows, Steven

1997-10-01

Color image coding at low bit rates is an area of research that is just being addressed in recent literature since the problems of storage and transmission of color images are becoming more prominent in many applications. Current trends in image coding exploit the advantage of subband/wavelet decompositions in reducing the complexity in optimal scalar/vector quantizer (SQ/VQ) design. Compression ratios (CRs) of the order of 10:1 to 20:1 with high visual quality have been achieved by using vector quantization of subband decomposed color images in perceptually weighted color spaces. We report the performance of a recently developed adaptive vector quantizer, namely, AFLC-VQ for effective reduction in bit rates while maintaining high visual quality of reconstructed color as well as monochrome images. For 24 bit color images, excellent visual quality is maintained upto a bit rate reduction to approximately 0.48 bpp (for each color plane or monochrome 0.16 bpp, CR 50:1) by using the RGB color space. Further tuning of the AFLC-VQ, and addition of an entropy coder module after the VQ stage results in extremely low bit rates (CR 80:1) for good quality, reconstructed images. Our recent study also reveals that for similar visual quality, RGB color space requires less bits/pixel than either the YIQ, or HIS color space for storing the same information when entropy coding is applied. AFLC-VQ outperforms other standard VQ and adaptive SQ techniques in retaining visual fidelity at similar bit rate reduction.

The unique contribution of manual chest compression-vibrations to airflow during physiotherapy in sedated, fully ventilated children.

PubMed

Gregson, Rachael K; Shannon, Harriet; Stocks, Janet; Cole, Tim J; Peters, Mark J; Main, Eleanor

2012-03-01

This study aimed to quantify the specific effects of manual lung inflations with chest compression-vibrations, commonly used to assist airway clearance in ventilated patients. The hypothesis was that force applied during the compressions made a significant additional contribution to increases in peak expiratory flow and expiratory to inspiratory flow ratio over and above that resulting from accompanying increases in inflation volume. Prospective observational study. Cardiac and general pediatric intensive care. Sedated, fully ventilated children. Customized force-sensing mats and a commercial respiratory monitor recorded force and respiration during physiotherapy. Percentage changes in peak expiratory flow, peak expiratory to inspiratory flow ratios, inflation volume, and peak inflation pressure between baseline and manual inflations with and without compression-vibrations were calculated. Analysis of covariance determined the relative contribution of changes in pressure, volume, and force to influence changes in peak expiratory flow and peak expiratory to inspiratory flow ratio. Data from 105 children were analyzed (median age, 1.3 yrs; range, 1 wk to 15.9 yrs). Force during compressions ranged from 15 to 179 N (median, 46 N). Peak expiratory flow increased on average by 76% during compressions compared with baseline ventilation. Increases in peak expiratory flow were significantly related to increases in inflation volume, peak inflation pressure, and force with peak expiratory flow increasing by, on average, 4% for every 10% increase in inflation volume (p < .001), 5% for every 10% increase in peak inflation pressure (p = .005), and 3% for each 10 N of applied force (p < .001). By contrast, increase in peak expiratory to inspiratory flow ratio was only related to applied force with a 4% increase for each 10 N of force (p < .001). These results provide evidence of the unique contribution of compression forces in increasing peak expiratory flow and peak expiratory to inspiratory flow ratio bias over and above that related to accompanying changes from manual hyperinflations. Force generated during compression-vibrations was the single significant factor in multivariable analysis to explain the increases in expiratory flow bias. Such increases in the expiratory bias provide theoretically optimal physiological conditions for cephalad mucus movement in fully ventilated children.

A Visual Basic program for analyzing oedometer test results and evaluating intergranular void ratio

NASA Astrophysics Data System (ADS)

Monkul, M. Murat; Önal, Okan

2006-06-01

A visual basic program (POCI) is proposed and explained in order to analyze oedometer test results. Oedometer test results have vital importance from geotechnical point of view, since settlement requirements usually control the design of foundations. The software POCI is developed in order perform the necessary calculations for convential oedometer test. The change of global void ratio and stress-strain characteristics can be observed both numerically and graphically. It enables the users to calculate some parameters such as coefficient of consolidation, compression index, recompression index, and preconsolidation pressure depending on the type and stress history of the soil. Moreover, it adopts the concept of intergranular void ratio which may be important especially in the compression behavior of sandy soils. POCI shows the variation of intergranular void ratio and also enables the users to calculate granular compression index.

Free-piston engine

DOEpatents

Van Blarigan, Peter

2001-01-01

A combustion system which can utilize high compression ratios, short burn durations, and homogeneous fuel/air mixtures in conjunction with low equivalence ratios. In particular, a free-piston, two-stroke autoignition internal combustion engine including an electrical generator having a linear alternator with a double-ended free piston that oscillates inside a closed cylinder is provided. Fuel and air are introduced in a two-stroke cycle fashion on each end, where the cylinder charge is compressed to the point of autoignition without spark plugs. The piston is driven in an oscillating motion as combustion occurs successively on each end. This leads to rapid combustion at almost constant volume for any fuel/air equivalence ratio mixture at very high compression ratios. The engine is characterized by high thermal efficiency and low NO.sub.x emissions. The engine is particularly suited for generating electrical current in a hybrid automobile.

Engine Performance and Knock Rating of Fuels for High-output Aircraft Engines

NASA Technical Reports Server (NTRS)

Rothbrock, A M; Biermann, Arnold E

1938-01-01

Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained on a single-cylinder test engine with aircraft-engine fuels varying from a fuel of 87 octane number to one 100 octane number plus 1 ml of tetraethyl lead per gallon. The data were obtained on a 5-inch by 5.75-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.50 to 8.75. The inlet-air temperature was varied from 120 to 280 F. and the inlet-air pressure from 30 inches of mercury absolute to the highest permissible. The limiting factors for the increase in compression ratio and in inlet-air pressure was the occurrence of either audible or incipient knock. The data are correlated to show that, for any one fuel,there is a definite relationship between the limiting conditions of inlet-air temperature and density at any compression ratio. This relationship is dependent on the combustion-gas temperature and density relationship that causes knock. The report presents a suggested method of rating aircraft-engine fuels based on this relationship. It is concluded that aircraft-engine fuels cannot be satisfactorily rated by any single factor, such as octane number, highest useful compression ratio, or allowable boost pressure. The fuels should be rated by a curve that expresses the limitations of the fuel over a variety of engine conditions.

Hypothalamic damage in multiple sclerosis correlates with disease activity, disability, depression, and fatigue.

PubMed

Kantorová, E; Poláček, H; Bittšanský, M; Baranovičová, E; Hnilicová, P; Čierny, D; Sivák, Š; Nosáľ, V; Zeleňák, K; Kurča, E

2017-04-01

Disturbances in the hypothalamo-pituitary axis are supposed to modulate activity of multiple sclerosis (MS). We hypothesised that the extent of HYP damage may determine severity of MS and may be associated with the disease evolution. We suggested fatigue and depression may depend on the degree of damage of the area. 33 MS patients with relapsing-remitting and secondary progressive disease, and 24 age and sex-related healthy individuals (CON) underwent 1H-MR spectroscopy (1H-MRS) of the hypothalamus. Concentrations of glutamate + glutamin (Glx), cholin (Cho), myoinositol (mIns), N-acetyl aspartate (NAA) expressed as ratio with creatine (Cr) and NAA were correlated with markers of disease activity (RIO score), Multiple Sclerosis Severity Scale (MSSS), Depressive-Severity Status Scale and Simple Numerical Fatigue Scale. Cho/Cr and NAA/Cr ratios were decreased and Glx/NAA ratio increased in MS patients vs CON. Glx/NAA, Glx/Cr, and mIns/NAA were significantly higher in active (RIO 1-2) vs non-active MS patients (RIO 0). Glx/NAA and Glx/Cr correlated with MSSS and fatigue score, and Glx/Cr with depressive score of MS patients. In CON, relationships between Glx/Cr and age, and Glx/NAA and fatigue score were inverse. Our study provides the first evidence about significant hypothalamic alterations correlating with clinical outcomes of MS, using 1H-MRS. The combination of increased Glu or mIns with reduced NAA in HYP reflects whole-brain activity of MS. In addition, excess of Glu is linked to severe disease course, depressive mood and fatigue in MS patients, suggesting superiority of Glu over other metabolites in determining MS burden.

Antidepressant effect detected on proton magnetic resonance spectroscopy in drug-naïve female patients with first-episode major depression.

PubMed

Kaymak, Semra Ulusoy; Demir, Başaran; Oğuz, Kader Karli; Sentürk, Senem; Uluğ, Berna

2009-06-01

Recent neuroimaging studies support functional and structural alterations in the dorsolateral prefrontal cortex (DLPFC), particularly on the left side in patients with major depressive disorders (MDD). The aim of the present study was to examine the biochemical characteristics of left DLPFC as measured on proton ((1)H) magnetic resonance spectroscopy (MRS) in patients with drug-naïve first-episode MDD and a healthy control group. A second aim was to assess the effect of antidepressant treatment on the metabolites of DLPFC. Short-echo single-voxel (1)H-MRS was done for the left DLPFC in 17 female drug-free MDD patients (mean age +/- SD, 30.9 +/- 6.9 years) and 13 matched control subjects (mean age +/- SD, 29.1 +/- 6.2 years) and was repeated at 8 weeks following antidepressant treatment. Comparison of baseline values indicated that there were no significant differences in any of the metabolite ratios (N-acetyl aspartate/creatine [NAA/Cr], myoinositol [Ino]/Cr, and choline [Cho]/Cr) between patients and controls. Significant differences were detected between pre- and post-treatment Ino/Cr ratios (0.67 +/- 0.13, 0.58 +/- 0.22, P = 0.032, respectively), although there was no difference in NAA/Cr and Cho/Cr ratios. Although no significant metabolic alterations exist in female patients with drug-naïve first-episode MDD as evaluated on (1)H-MRS, an increase in Ino/Cr was observed following 8-week antidepressant treatment. These findings give rise to the possibility that non-neuronal cells, particularly glial cells that are probably damaged, play a role in the action of antidepressant treatment.

Effects of chromium and chromium + vitamin C combination on metabolic, oxidative, and fear responses of broilers transported under summer conditions

NASA Astrophysics Data System (ADS)

Perai, A. H.; Kermanshahi, H.; Moghaddam, H. Nassiri; Zarban, A.

2015-04-01

A total of 240 female broilers (42 days old) were randomly assigned to four groups with six replicates and fed either a basal diet (two control groups) or a basal diet supplemented with either 1,200 μg Cr+3 from chromium (Cr) methionine/kg (Cr group) or 1,200 μg Cr+3 from Cr methionine plus 800 mg vitamin C (Vit C)/kg of diet (Cr + Vit C group). After 7 days on the dietary treatment, all groups except one of the controls were transported for 3 h under the summer conditions. Performance parameters were not influenced by dietary treatments. The plasma concentrations of insulin, triiodothyronine, triglyceride, and the ratio of triiodothyronine/thyroxin were decreased and the ratio of glucose/insulin was increased due to transport process. Road transportation also increased the plasma concentrations of protein, cholesterol, aspartate aminotransferase, and creatine kinase and decreased the concentration of low-density lipoprotein cholesterol in the Cr + Vit C group. The pretransport concentrations of insulin and triiodothyronine were highest in the Cr + Vit C group. The concentration of phosphorous was lower in the Cr group than that in the other groups after transport. No significant effects of dietary treatments were observed on the other biochemical parameters. Transport increased malondialdehyde concentration in the control group and did not change plasma total antioxidant capacity and erythrocyte glutathione peroxidase activity. Either in combination or alone, Cr increased plasma total antioxidant capacity (before transport P ≤ 0.05, after transport P = 0.07) but did not affect the concentration of malondialdehyde and activity of glutathione peroxidase. The duration of tonic immobility (TI) was similar between nontransported control chicks and transported chicks without any supplements. Pretreatment with Cr + Vit C significantly reduced the duration of TI.

Extremely 54Cr- and 50Ti-rich Presolar Oxide Grains in a Primitive Meteorite: Formation in Rare Types of Supernovae and Implications for the Astrophysical Context of Solar System Birth

NASA Astrophysics Data System (ADS)

Nittler, Larry R.; O’D. Alexander, Conel M.; Liu, Nan; Wang, Jianhua

2018-04-01

We report the identification of 19 presolar oxide grains from the Orgueil CI meteorite with substantial enrichments in 54Cr, with 54Cr/52Cr ratios ranging from 1.2 to 56 times the solar value. The most enriched grains also exhibit enrichments at mass-50, most likely due in part to 50Ti, but close-to-normal or depleted 53Cr/52Cr ratios. There is a strong inverse relationship between 54Cr enrichment and grain size; the most extreme grains are all <80 nm in diameter. Comparison of the isotopic data with predictions of nucleosynthesis calculations indicate that these grains most likely originated in either rare, high-density Type Ia supernovae (SN Ia), or in electron-capture supernovae (ECSN), which may occur as the end stage of evolution for stars of mass 8–10 M ⊙. This is the first evidence for preserved presolar grains from either type of supernova. An ECSN origin is attractive, as these likely occur much more frequently than high-density SN Ia, and their evolutionary timescales (∼20 Myr) are comparable to those of molecular clouds. Self-pollution of the Sun’s parent cloud from an ECSN may explain the heterogeneous distribution of n-rich isotopic anomalies in planetary materials, including a recently reported dichotomy in Mo isotopes in the solar system. The stellar origins of three grains with solar 54Cr/52Cr, but anomalies in 50Cr or 53Cr, as well as of a grain enriched in 57Fe, are unclear.

Microstructure and property of diamond-like carbon films with Al and Cr co-doping deposited using a hybrid beams system

NASA Astrophysics Data System (ADS)

Dai, Wei; Liu, Jingmao; Geng, Dongsen; Guo, Peng; Zheng, Jun; Wang, Qimin

2016-12-01

DLC films with weak carbide former Al and carbide former Cr co-doping (Al:Cr-DLC) were deposited by a hybrid beams system comprising an anode-layer linear ion beam source (LIS) and high power impulse magnetron sputtering using a gas mixture of C2H2 and Ar as the precursor. The doped Al and Cr contents were controlled via adjusting the C2H2 fraction in the gas mixture. The composition, microstructure, compressive stress, mechanical properties and tribological behaviors of the Al:Cr-DLC films were researched carefully using X-ray photoelectron spectroscopy, transmission electron microscopy, Raman spectroscopy, stress-tester, nanoindentation and ball-on-plate tribometer as function of the C2H2 fraction. The results show that the Al and Cr contents in the films increased continuously as the C2H2 fraction decreased. The doped Cr atoms preferred to bond with the carbon while the Al atoms mainly existed in metallic state. Structure modulation with alternate multilayer consisted of Al-poor DLC layer and Al-rich DLC layer was found in the films. Those periodic Al-rich DLC layers can effectively release the residual stress of the films. On the other hand, the formation of the carbide component due to Cr incorporation can help to increase the film hardness. Accordingly, the residual stress of the DLC films can be reduced without sacrificing the film hardness though co-doping Al and Cr atoms. Furthermore, it was found that the periodic Al-rich layer can greatly improve the elastic resilience of the DLC films and thus decreases the film friction coefficient and wear rate significantly. However, the existence of the carbide component would cause abrasive wear and thus deteriorate the wear performance of the films.

Outer planet Pioneer imaging communications system study. [data compression

NASA Technical Reports Server (NTRS)

1974-01-01

The effects of different types of imaging data compression on the elements of the Pioneer end-to-end data system were studied for three imaging transmission methods. These were: no data compression, moderate data compression, and the advanced imaging communications system. It is concluded that: (1) the value of data compression is inversely related to the downlink telemetry bit rate; (2) the rolling characteristics of the spacecraft limit the selection of data compression ratios; and (3) data compression might be used to perform acceptable outer planet mission at reduced downlink telemetry bit rates.

The Urinary Uric Acid/Creatinine Ratio is An Adjuvant Marker for Perinatal Asphyxia.

PubMed

Bhongir, Aparna Varma; Yakama, Akhil Varma Venkata; Saha, Subhajit; Radia, Sejal B; Pabbati, Jayalakshmi

2015-09-01

To assess the urinary uric acid/creatinine ratio (UA/Cr) in relation to Apgar score and cord blood gas analysis in identification of perinatal asphyxia and to define the cutoff values. case control study. The newborns admitted in the department of pediatrics and NICU of Mediciti Institute of Medical Science, Ghanpur, Medchal mandal, Telangana from May-July 2011 were enrolled. The study was conducted on 31 (18 males, 13 females) controls and 18 (12males, 6 females) asphyxiated neonates. 5ml of arterial cord blood of newborn collected at the time of birth and spot urine samples were collected within 24-72 hours of life. Cord blood gas analysis were done immediately and Urinary uric acid was measured by modified Uricase method, urinary creatinine by modified kinetic Jaffe's reaction. The mean urinary uric acid and creatinine ratio (2.58± 0.48 vs 1.89 ± 0.59) is significantly higher in Asphyxiated group than in the control group. The umbilical cord blood pH had significant positive correlation with 1 st minute Apgar score (r= 0.41, p=0.003), 5 th minute Apgar (r= 0.44, p=0.002), while urinary UA/Cr ratio had significant negative correlation with cord blood pH (r= -0.63, p=0.002). Urinary UA/Cr ratio with criterion of >2.43 had 80% sensitivity, 87.5% specificity with AUC of 0.84 (p=0.003) had a better predictive value. Urinary UA/Cr ratio is easy, non-invasive, painless and economical adjuvant parameter with better predictive value for diagnosing perinatal asphyxia with simple diagnostic equipment.

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

NASA Astrophysics Data System (ADS)

Nagaraju, S.; Vasantharaja, P.; Brahadees, G.; Vasudevan, M.; Mahadevan, S.

2017-12-01

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

Microstructures and Mechanical Properties of Two-Phase Alloys Based on NbCr(2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cady, C.M.; Chen, K.C.; Kotula, P.G.

A two-phase, Nb-Cr-Ti alloy (bee+ C15 Laves phase) has been developed using several alloy design methodologies. In effort to understand processing-microstructure-property relationships, diffment processing routes were employed. The resulting microstructure and mechanical properties are discussed and compared. Plasma arc-melted samples served to establish baseline, . . . as-cast properties. In addition, a novel processing technique, involving decomposition of a supersaturated and metastable precursor phase during hot isostatic pressing (HIP), was used to produce a refined, equilibrium two-phase microstructure. Quasi-static compression tests as a ~ function of temperature were performed on both alloy types. Different deformation mechanisms were encountered based uponmore » temperature and microstructure.« less

Single crystal plastic behavior of a single-phase, face-center-cubic-structured, equiatomic FeNiCrCo alloy

DOE PAGES

Wu, Zhenggang; Gao, Y. F.; Bei, Hongbin

2015-07-25

To understand the fundamental deformation mechanisms of compositionally complex alloys, single crystals of a multi-component equiatomic FeNiCoCr alloy with face-centered cubic (FCC) structure were grown for mechanical studies. Similarly to typical FCC pure metals, slip trace analyses indicate that dislocation slips take place on (1 1 1) planes along [11¯0] directions. The critical resolved shear stress (CRSS) obeys the Schmid law at both 77 and 293 K, and tension–compression asymmetry is not observed. Although this material slips in a normal FCC manner both at 293 and 77 K, compared to typical FCC metals the CRSS’s strong temperature dependence is abnormal.

Evaluation of Microstructure and Mechanical Properties of Nano-Y2O3-Dispersed Ferritic Alloy Synthesized by Mechanical Alloying and Consolidated by High-Pressure Sintering

NASA Astrophysics Data System (ADS)

Karak, Swapan Kumar; Dutta Majumdar, J.; Witczak, Zbigniew; Lojkowski, Witold; Ciupiński, Łukasz; Kurzydłowski, K. J.; Manna, Indranil

2013-06-01

In this study, an attempt has been made to synthesize 1.0 wt pct nano-Y2O3-dispersed ferritic alloys with nominal compositions: 83.0 Fe-13.5 Cr-2.0 Al-0.5 Ti (alloy A), 79.0 Fe-17.5 Cr-2.0 Al-0.5 Ti (alloy B), 75.0 Fe-21.5 Cr-2.0 Al-0.5 Ti (alloy C), and 71.0 Fe-25.5 Cr-2.0 Al-0.5 Ti (alloy D) steels (all in wt pct) by solid-state mechanical alloying route and consolidation the milled powder by high-pressure sintering at 873 K, 1073 K, and 1273 K (600°C, 800°C, and 1000°C) using 8 GPa uniaxial pressure for 3 minutes. Subsequently, an extensive effort has been undertaken to characterize the microstructural and phase evolution by X-ray diffraction, scanning and transmission electron microscopy, and energy dispersive spectroscopy. Mechanical properties including hardness, compressive strength, Young's modulus, and fracture toughness were determined using micro/nano-indentation unit and universal testing machine. The present ferritic alloys record extraordinary levels of compressive strength (from 1150 to 2550 MPa), Young's modulus (from 200 to 240 GPa), indentation fracture toughness (from 3.6 to 15.4 MPa√m), and hardness (from13.5 to 18.5 GPa) and measure up to 1.5 through 2 times greater strength but with a lower density (~7.4 Mg/m3) than other oxide dispersion-strengthened ferritic steels (<1200 MPa) or tungsten-based alloys (<2200 MPa). Besides superior mechanical strength, the novelty of these alloys lies in the unique microstructure comprising uniform distribution of either nanometric (~10 nm) oxide (Y2Ti2O7/Y2TiO5 or un-reacted Y2O3) or intermetallic (Fe11TiY and Al9.22Cr2.78Y) particles' ferritic matrix useful for grain boundary pinning and creep resistance.

Ignition and combustion: Low compression ratio, high output diesel

NASA Technical Reports Server (NTRS)

1981-01-01

The feasibility of converting a spark ignition aircraft engine GTSI0-520 to compression ignition without increasing the peak combustion pressure of 1100 lbs/sq.in. was determined. The final contemplated utilized intake air heating at idle and light load and a compression ratio of about 10:1 with a small amount of fumigation (the addition of about 15% fuel into the combustion air before the cylinder). The engine used was a modification of a Continental-Teledyne gasoline engine cylinder from the GTSI0-520 supercharged aircraft engine.

The Effect of Fuel Composition, Compression Pressure, and Fuel-Air Ratio on the Compression-Ignition Characteristics of Several Fuels

DTIC Science & Technology

1948-03-01

to this arbitrary value as ntandard. The compression time was maintained unifcum by uElng a ccnstent . driving ~ essure of 500 pounds per squ=e inch...ir ratio,0.066 (chemlo~ correct); initial~ essure , 14.7 lb/sq in. abs.; intt Ml temperature, 609° F abs~ Ignitiondelay Compres- Compres- sion...chemically correct); initial ~ essure , 14.7 lb/sq in. abso; fimal pressures 379 lb/sq in. abs.; initial temperatume~ 6090 F abs.; final temperature, 1340° F abs

Altered chemical metabolites in the amygdala-hippocampus region contribute to autistic symptoms of autism spectrum disorders.

PubMed

Endo, Taro; Shioiri, Toshiki; Kitamura, Hideaki; Kimura, Teruo; Endo, Sumio; Masuzawa, Naio; Someya, Toshiyuki

2007-11-01

Although several previous studies have been conducted, the neural basis of autism spectrum disorder (ASD) is poorly understood. The objective of the present study was to determine whether individuals with ASD have altered brain chemical metabolites and whether such alterations are related to their autistic symptoms. N-acetylaspartate (NAA)/creatine (Cr) and choline/Cr ratios in the right medial temporal lobe (MTL), medial prefrontal cortex, and cerebellar vermis were measured in 38 individuals with ASD (mean age = 12.9 years), including 12 with autism, 15 with Asperger's Disorder, and 11 with pervasive developmental disorder not otherwise specified (PDD-NOS), and 16 matched healthy control subjects (mean age = 11.5 years) with proton magnetic resonance spectroscopy. Autistic symptoms were assessed by the Childhood Autistic Rating Scale-Tokyo Version. There was a significant group difference for NAA/Cr ratio in the right MTL between the autism, Asperger's Disorder, PDD-NOS, and control groups (p < .001), and the autism group had a significantly lower NAA/Cr ratio compared with the PDD-NOS (p < .001) and control (p < .001) groups. In the ASD group, there was a significant negative correlation between NAA/Cr ratio in the right MTL and their Childhood Autistic Rating Scale-Tokyo Version total scores (r = -.44, p = .01) and subscales of emotional response (r = -.38, p = .02) and listening response (r = -.54, p = .001). The results of the present study suggest that subjects with ASD have abnormalities of neural integrity in the amygdala-hippocampus region that are related to their severity and social impairments.

GABA Levels Are Decreased After Stroke and GABA Changes During Rehabilitation Correlate With Motor Improvement

PubMed Central

Blicher, Jakob Udby; Near, Jamie; Næss-Schmidt, Erhard; Stagg, Charlotte J.; Johansen-Berg, Heidi; Nielsen, Jørgen Feldbæk; Østergaard, Leif; Ho, Yi-Ching Lynn

2017-01-01

Background and Objective γ-Aminobutyric acid (GABA) is the dominant inhibitory neurotransmitter in the brain and is important in motor learning. We aimed to measure GABA content in primary motor cortex poststroke (using GABA-edited magnetic resonance spectroscopy [MRS]) and in relation to motor recovery during 2 weeks of constraint-induced movement therapy (CIMT). Methods Twenty-one patients (3-12 months poststroke) and 20 healthy subjects were recruited. Magnetic resonance imaging structural T1 and GABA-edited MRS were performed at baseline and after CIMT, and once in healthy subjects. GABA:creatine (GABA:Cr) ratio was measured by GABA-edited MRS. Motor function was measured using Wolf Motor Function Test (WMFT). Results Baseline comparison between stroke patients (n = 19) and healthy subjects showed a significantly lower GABA:Cr ratio in stroke patients (P < .001) even after correcting for gray matter content in the voxel (P < .01) and when expressing GABA relative to N-acetylaspartic acid (NAA; P = .03). After 2 weeks of CIMT patients improved significantly on WMFT, but no consistent change across the group was observed for the GABA:Cr ratio (n = 17). However, the extent of improvement on WMFT correlated significantly with the magnitude of GABA:Cr changes (P < .01), with decreases in GABA:Cr ratio being associated with better improvements in motor function. Conclusions In patients 3 to 12 months poststroke, GABA levels are lower in the primary motor cortex than in healthy subjects. The observed association between GABA and recovery warrants further studies on the potential use of GABA MRS as a biomarker in poststroke recovery. PMID:25055837

Mn-Cr isotopic systematics of Chainpur chondrules and bulk ordinary chondrites

NASA Technical Reports Server (NTRS)

Nyquist, L.; Lindstrom, D.; Wiesmann, H.; Bansal, B.; Shih, C.-Y.; Mittlefehldt, D.; Martinez, R.; Wentworth, S.

1994-01-01

We report on ongoing study of the Mn-Cr systematics of individual Chainpur (LL3.4) chondrules and compare the results to those for bulk ordinary chondrites. Twenty-eight chondrules were surveyed for abundances of Mn, Cr, Na, Fe, Sc, Hf, Ir, and Zn by INAA. Twelve were chosen for SEM/EDX and high-precision Cr-isotopic studies on the basis of LL-chondrite-normalized Mn(LL), Sc(LL), (Mn/Fe)(LL), and (Sc/Fe)(LL) as well as their Mn/Cr ratios. Classification into textural types follows from SEM/EDX examination of interior surfaces.

Effect of first-line endocrine therapy in patients with hormone-sensitive advanced breast cancer: a network meta-analysis.

PubMed

Zhang, Tingting; Feng, Fubin; Zhao, Wenge; Tian, Jinhui; Yao, Yan; Zhou, Chao; Dong, Shengjie; Wang, Congcong; Zang, Chuanxin; Lv, Qingliang; Sun, Changgang

2018-01-01

Endocrine therapy is the cornerstone treatment for patients with hormone receptor-positive advanced breast cancer. We aimed to assess the effectiveness of various first-line endocrine monotherapies or combinations to determine the optimal sequence in a network meta-analysis. We searched PubMed, EMBASE, and the Cochrane Library for randomized controlled trials (RCTs) from inception up to November 21, 2017. We included only RCTs that assessed the effectiveness of the following treatments as a monotherapy or in combination as the first-line treatment: tamoxifen, anastrozole, letrozole, exemestane, fulvestrant, palbociclib, and ribociclib. The results were presented with pooled odds ratio or hazard ratio (HR), and 95% credible interval (CrI). The primary outcomes were objective response rate (ORR) and progression-free survival/time to progression. A total of 16 eligible articles (14 RCTs) involving 6,602 patients treated with 10 different first-line endocrine therapies were assessed in our network meta-analysis. Palbociclib plus letrozole was superior to anastrozole, letrozole, exemestane, fulvestrant 500 mg, and anastrozole plus fulvestrant (loading dose) (HR=0.44, 95% CrI: 0.33-0.58; HR=0.56, 95% CrI: 0.45-0.68; HR=0.45, 95% CrI: 0.32-0.61; HR=0.58, 95% CrI: 0.42-0.81; HR=0.50, 95% CrI: 0.37-0.68; respectively). However, there is no significant advantage compared with ribociclib plus letrozole (HR=1.00, 95% CrI: 0.72-1.39). In terms of ORR, ribociclib plus letrozole is more effective than palbociclib plus letrozole (odds ratio=1.30, 95% CrI: 0.83-2.02). Palbociclib plus letrozole and ribociclib plus letrozole might be the optimal first-line endocrine therapeutic choices for hormone receptor-positive/human epidermal growth factor receptor 2-negative advanced breast cancer due to a longer progression-free survival/time to progression and a more efficacious ORR.

Screening for X-linked creatine transporter (SLC6A8) deficiency via simultaneous determination of urinary creatine to creatinine ratio by tandem mass-spectrometry.

PubMed

Mercimek-Mahmutoglu, Saadet; Muehl, Adolf; Salomons, Gajja S; Neophytou, Birgit; Moeslinger, Dorothea; Struys, Eduard; Bodamer, Olaf A; Jakobs, Cornelis; Stockler-Ipsiroglu, Sylvia

2009-04-01

High urinary creatine to creatinine ratio (U-CrCrtR) is a potential diagnostic marker of X-linked creatine transporter (SLC6A8) deficiency. We developed a tandem mass-spectrometry method to simultaneously determine urinary creatine and creatinine in 975 individuals (0-18 years). U-CrCrtR increased up to 8 years and decreased thereafter. U-CrCrtR was 2.29 and 2.12 (99th percentile: 1.87) in two males with subsequently confirmed SLC6A8 mutations. The frequency of SLC6A8 deficiency was 2.3% in 157 males at risk.

Lack of effect of oral choline supplement on the concentrations of choline metabolites in human brain.

PubMed

Tan, J; Bluml, S; Hoang, T; Dubowitz, D; Mevenkamp, G; Ross, B

1998-06-01

Recent reports suggest that oral choline supplement may alter the cerebral choline/creatine (Cho/Cr) ratio and might be used to treat neurodegenerative disorders of cholinergic transmission. Using both 1H and 31P MRS, we reexamined the Cho/Cr ratio and quantified cerebral choline and its major constituents: phosphoethanolamine (PE), phosphorylcholine (PC), glycerophosphorylethanolamine (GPE), and glycerophosphorylcholine (GPC). In the four brain locations examined, no significant increases in Cho/Cr, [Cho], or in its major constituents were found in response to an oral challenge of 50 mg/kg of choline bitartrate. Oral choline did not significantly affect human cerebral metabolism in the short term.

The influence of texture on the reversible elastocaloric effect of a polycrystalline Ni50Mn32In16Cr2 alloy

NASA Astrophysics Data System (ADS)

Hernández-Navarro, Fernando; Camarillo-Garcia, Juan-Pablo; Aguilar-Ortiz, Christian-Omar; Flores-Zúñiga, Horacio; Ríos, David; González, José-Gonzalo; Álvarez-Alonso, Pablo

2018-04-01

We have studied the correlation between the elastocaloric effect and the crystallographic direction where a uniaxial stress is applied in a textured polycrystalline Ni-Mn-In-Cr ferromagnetic shape memory alloy; this alloy displays martensitic transformation around room temperature and presents an L21 cubic structure in the austenite phase. The texture in the material was induced by simple arc melting synthesis; using inverse pole figures, a favored grain growth was shown in the direction [001] perpendicular to the cooled surface. The elastocaloric effect was determined by direct measurements of the adiabatic temperature change (ΔTadme), while compressive stress was applied and released; hereby, it has been shown that it is possible to exploit the columnar growth texture in order to obtain a large and reversible elastocaloric effect. The reversible elastocaloric response was measured between 280 and 310 K by applying moderate stresses of 50, 75, and 100 MPa in the [001], [111], and [011] directions. A strong interrelation was found in the cyclic ΔTadme values of -3.9, -2.0, and -1.3 K after unloading a compressive stress of 100 MPa applied mainly in the [001], [111], and [011] directions, respectively.

Visibility of wavelet quantization noise

NASA Technical Reports Server (NTRS)

Watson, A. B.; Yang, G. Y.; Solomon, J. A.; Villasenor, J.

1997-01-01

The discrete wavelet transform (DWT) decomposes an image into bands that vary in spatial frequency and orientation. It is widely used for image compression. Measures of the visibility of DWT quantization errors are required to achieve optimal compression. Uniform quantization of a single band of coefficients results in an artifact that we call DWT uniform quantization noise; it is the sum of a lattice of random amplitude basis functions of the corresponding DWT synthesis filter. We measured visual detection thresholds for samples of DWT uniform quantization noise in Y, Cb, and Cr color channels. The spatial frequency of a wavelet is r 2-lambda, where r is display visual resolution in pixels/degree, and lambda is the wavelet level. Thresholds increase rapidly with wavelet spatial frequency. Thresholds also increase from Y to Cr to Cb, and with orientation from lowpass to horizontal/vertical to diagonal. We construct a mathematical model for DWT noise detection thresholds that is a function of level, orientation, and display visual resolution. This allows calculation of a "perceptually lossless" quantization matrix for which all errors are in theory below the visual threshold. The model may also be used as the basis for adaptive quantization schemes.

Microstructure and mechanical properties of zirconium doped NiAl/Cr(Mo) hypoeutectic alloy prepared by injection casting

NASA Astrophysics Data System (ADS)

Sheng, L. Y.; Du, B. N.; Guo, J. T.

2017-01-01

NiAl based materials has been considered as most potential candidate of turbine blade, due to its excellent high-temperature properties. However the bad room-temperature properties handicap its application. In the present paper, the zirconium doped NiAl/Cr(Mo) hypoeutectic alloy is fabricated by conventional casting and injection casting technology to improve its room-temperature properties. The microstructure and compressive properties at different temperatures of the conventionally-cast and injection-cast were investigated. The results exhibit that the conventionally-cast alloy comprises coarse primary NiAl phase and eutectic cell, which is dotted with irregular Ni2AlZr Heusler phase. Compared with the conventionally-cast alloy, the injection-cast alloy possesses refined the primary NiAl, eutectic cell and eutectic lamella. In addition, the Ni2AlZr Heusler phase become smaller and distribute uniformly. Moreover, the injection casting decrease the area fraction of primary NiAl phase at the cell interior or cell boundaries. The compressive ductility and yield strength of the injection-cast alloy at room temperature increase by about 100% and 35% over those of conventionally-cast alloy, which should be ascribed to the microstructure optimization.

The role of thermal shock in cyclic oxidation

NASA Technical Reports Server (NTRS)

Lowell, C. E.; Deadmore, D. L.

1978-01-01

The effect of thermal shock on the spalling of oxides from the surfaces of several commercial alloys was determined. The average cooling rate was varied from approximately 240 C per second to less than 1.0 C per second during cyclic oxidation tests in air. The tests consisted of one hundred cycles of one hour at the maximum temperature (1100 or 1200 C). The alloys were HOS-875, TD-Ni, TD-NiCrAl, IN-601, IN-702, and B-1900 plus Hf. All of these alloys exhibited partial spalling within the oxide rather than total oxide loss down to bare metal. Thermal shock resulted in deformation of the metal which in turn resulted, in most cases, in changing the oxide failure mode from compressive to tensile. Tensile failures were characterized by cracking of the oxide and little loss, while compressive failures were characterized by explosive loss of platelets of oxide. This behavior was confirmed by examination of mechanically stressed oxide scales. The thermally shocked oxides spalled less than the slow cooled samples with the exception of TD-NiCrAl. This material failed in a brittle manner rather than by plastic deformation.

Stereo sequence transmission via conventional transmission channel

NASA Astrophysics Data System (ADS)

Lee, Ho-Keun; Kim, Chul-Hwan; Han, Kyu-Phil; Ha, Yeong-Ho

2003-05-01

This paper proposes a new stereo sequence transmission technique using digital watermarking for compatibility with conventional 2D digital TV. We, generally, compress and transmit image sequence using temporal-spatial redundancy between stereo images. It is difficult for users with conventional digital TV to watch the transmitted 3D image sequence because many 3D image compression methods are different. To solve such a problem, in this paper, we perceive the concealment of new information of digital watermarking and conceal information of the other stereo image into three channels of the reference image. The main target of the technique presented is to let the people who have conventional DTV watch stereo movies at the same time. This goal is reached by considering the response of human eyes to color information and by using digital watermarking. To hide right images into left images effectively, bit-change in 3 color channels and disparity estimation according to the value of estimated disparity are performed. The proposed method assigns the displacement information of right image to each channel of YCbCr on DCT domain. Each LSB bit on YCbCr channels is changed according to the bits of disparity information. The performance of the presented methods is confirmed by several computer experiments.

Modeling constitutive behavior of a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel under hot compression using artificial neural network

NASA Astrophysics Data System (ADS)

Mandal, Sumantra

2006-11-01

ABSTRACT In this paper, an artificial neural network (ANN) model has been suggested to predict the constitutive flow behavior of a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel under hot deformation. Hot compression tests in the temperature range 850°C- 1250°C and strain rate range 10-3-102 s-1 were carried out. These tests provided the required data for training the neural network and for subsequent testing. The inputs of the neural network are strain, log strain rate and temperature while flow stress is obtained as output. A three layer feed-forward network with ten neurons in a single hidden layer and back-propagation learning algorithm has been employed. A very good correlation between experimental and predicted result has been obtained. The effect of temperature and strain rate on flow behavior has been simulated employing the ANN model. The results have been found to be consistent with the metallurgical trend. Finally, a monte carlo analiysis has been carried out to find out the noise sensitivity of the developed model.

Hot deformation characteristics of as-cast high-Cr ultra-super-critical rotor steel with columnar grains

NASA Astrophysics Data System (ADS)

Ding, Zong-ye; Hu, Qiao-dan; Zeng, Long; Li, Jian-guo

2016-11-01

Isothermal hot compression tests of as-cast high-Cr ultra-super-critical (USC) rotor steel with columnar grains perpendicular to the compression direction were carried out in the temperature range from 950 to 1250°C at strain rates ranging from 0.001 to 1 s-1. The softening mechanism was dynamic recovery (DRV) at 950°C and the strain rate of 1 s-1, whereas it was dynamic recrystallization (DRX) under the other conditions. A modified constitutive equation based on the Arrhenius model with strain compensation reasonably predicted the flow stress under various deformation conditions, and the activation energy was calculated to be 643.92 kJ•mol-1. The critical stresses of dynamic recrystallization under different conditions were determined from the work-hardening rate ( θ)-flow stress ( σ) and -∂ θ/∂ σ-σ curves. The optimum processing parameters via analysis of the processing map and the softening mechanism were determined to be a deformation temperature range from 1100 to 1200°C and a strain-rate range from 0.001 to 0.08 s-1, with a power dissipation efficiency η greater than 31%.

The role of bulk viscosity on the decay of compressible, homogeneous, isotropic turbulence

NASA Astrophysics Data System (ADS)

Johnsen, Eric; Pan, Shaowu

2016-11-01

The practice of neglecting bulk viscosity in studies of compressible turbulence is widespread. While exact for monatomic gases and unlikely to strongly affect the dynamics of fluids whose bulk-to-shear viscosity ratio is small and/or of weakly compressible turbulence, this assumption is not justifiable for compressible, turbulent flows of gases whose bulk viscosity is orders of magnitude larger than their shear viscosities (e.g., CO2). To understand the mechanisms by which bulk viscosity and the associated phenomena affect compressible turbulence, we conduct DNS of freely decaying compressible, homogeneous, isotropic turbulence for ratios of bulk-to-shear viscosity ranging from 0-1000. Our simulations demonstrate that bulk viscosity increases the decay rate of turbulent kinetic energy; while enstrophy exhibits little sensitivity to bulk viscosity, dilatation is reduced by an order of magnitude within the two eddy turnover time. Via a Helmholtz decomposition of the flow, we determined that bulk viscosity damps the dilatational velocity and reduces dilatational-solenoidal exchanges, as well as pressure-dilatation coupling. In short, bulk viscosity renders compressible turbulence incompressible by reducing energy transfer between translational and internal modes.

JPEG2000 still image coding quality.

PubMed

Chen, Tzong-Jer; Lin, Sheng-Chieh; Lin, You-Chen; Cheng, Ren-Gui; Lin, Li-Hui; Wu, Wei

2013-10-01

This work demonstrates the image qualities between two popular JPEG2000 programs. Two medical image compression algorithms are both coded using JPEG2000, but they are different regarding the interface, convenience, speed of computation, and their characteristic options influenced by the encoder, quantization, tiling, etc. The differences in image quality and compression ratio are also affected by the modality and compression algorithm implementation. Do they provide the same quality? The qualities of compressed medical images from two image compression programs named Apollo and JJ2000 were evaluated extensively using objective metrics. These algorithms were applied to three medical image modalities at various compression ratios ranging from 10:1 to 100:1. Following that, the quality of the reconstructed images was evaluated using five objective metrics. The Spearman rank correlation coefficients were measured under every metric in the two programs. We found that JJ2000 and Apollo exhibited indistinguishable image quality for all images evaluated using the above five metrics (r > 0.98, p < 0.001). It can be concluded that the image quality of the JJ2000 and Apollo algorithms is statistically equivalent for medical image compression.

[Lossless ECG compression algorithm with anti- electromagnetic interference].

PubMed

Guan, Shu-An

2005-03-01

Based on the study of ECG signal features, a new lossless ECG compression algorithm is put forward here. We apply second-order difference operation with anti- electromagnetic interference to original ECG signals and then, compress the result by the escape-based coding model. In spite of serious 50Hz-interference, the algorithm is still capable of obtaining a high compression ratio.

Highly Efficient Compression Algorithms for Multichannel EEG.

PubMed

Shaw, Laxmi; Rahman, Daleef; Routray, Aurobinda

2018-05-01

The difficulty associated with processing and understanding the high dimensionality of electroencephalogram (EEG) data requires developing efficient and robust compression algorithms. In this paper, different lossless compression techniques of single and multichannel EEG data, including Huffman coding, arithmetic coding, Markov predictor, linear predictor, context-based error modeling, multivariate autoregression (MVAR), and a low complexity bivariate model have been examined and their performances have been compared. Furthermore, a high compression algorithm named general MVAR and a modified context-based error modeling for multichannel EEG have been proposed. The resulting compression algorithm produces a higher relative compression ratio of 70.64% on average compared with the existing methods, and in some cases, it goes up to 83.06%. The proposed methods are designed to compress a large amount of multichannel EEG data efficiently so that the data storage and transmission bandwidth can be effectively used. These methods have been validated using several experimental multichannel EEG recordings of different subjects and publicly available standard databases. The satisfactory parametric measures of these methods, namely percent-root-mean square distortion, peak signal-to-noise ratio, root-mean-square error, and cross correlation, show their superiority over the state-of-the-art compression methods.

Visually lossless compression of digital hologram sequences

NASA Astrophysics Data System (ADS)

Darakis, Emmanouil; Kowiel, Marcin; Näsänen, Risto; Naughton, Thomas J.

2010-01-01

Digital hologram sequences have great potential for the recording of 3D scenes of moving macroscopic objects as their numerical reconstruction can yield a range of perspective views of the scene. Digital holograms inherently have large information content and lossless coding of holographic data is rather inefficient due to the speckled nature of the interference fringes they contain. Lossy coding of still holograms and hologram sequences has shown promising results. By definition, lossy compression introduces errors in the reconstruction. In all of the previous studies, numerical metrics were used to measure the compression error and through it, the coding quality. Digital hologram reconstructions are highly speckled and the speckle pattern is very sensitive to data changes. Hence, numerical quality metrics can be misleading. For example, for low compression ratios, a numerically significant coding error can have visually negligible effects. Yet, in several cases, it is of high interest to know how much lossy compression can be achieved, while maintaining the reconstruction quality at visually lossless levels. Using an experimental threshold estimation method, the staircase algorithm, we determined the highest compression ratio that was not perceptible to human observers for objects compressed with Dirac and MPEG-4 compression methods. This level of compression can be regarded as the point below which compression is perceptually lossless although physically the compression is lossy. It was found that up to 4 to 7.5 fold compression can be obtained with the above methods without any perceptible change in the appearance of video sequences.

Normalized stiffness ratios for mechanical characterization of isotropic acoustic foams.

PubMed

Sahraoui, Sohbi; Brouard, Bruno; Benyahia, Lazhar; Parmentier, Damien; Geslain, Alan

2013-12-01

This paper presents a method for the mechanical characterization of isotropic foams at low frequency. The objective of this study is to determine the Young's modulus, the Poisson's ratio, and the loss factor of commercially available foam plates. The method is applied on porous samples having square and circular sections. The main idea of this work is to perform quasi-static compression tests of a single foam sample followed by two juxtaposed samples having the same dimensions. The load and displacement measurements lead to a direct extraction of the elastic constants by means of normalized stiffness and normalized stiffness ratio which depend on Poisson's ratio and shape factor. The normalized stiffness is calculated by the finite element method for different Poisson ratios. The no-slip boundary conditions imposed by the loading rigid plates create interfaces with a complex strain distribution. Beforehand, compression tests were performed by means of a standard tensile machine in order to determine the appropriate pre-compression rate for quasi-static tests.

YZ (Y = V, Cr; Z = Al, Ga) under pressure: a DFT study

NASA Astrophysics Data System (ADS)

Seema, K.; Kumar, Ranjan

2014-09-01

The structural, electronic and magnetic properties of Co-based Heusler compounds Co2YZ (Y = V, Cr; Z = Al, Ga) under pressure are studied using first principles density functional theory. The calculations are performed within generalized gradient approximation. The total magnetic moment decreases slightly on compression. Under application of external pressure, the valence band and conduction band are shifted downward which leads to the modification of electronic structure. There exists an indirect band gap along Г- X for all the alloys studied. Co2CrAl shows half-metallic nature up to 85 GPa. After this pressure transition from true half-metallic behavior to nearly half-metallic behavior is observed and at 90 GPa it shows metallic behavior. Co2CrGa shows nearly half-metallic behavior at ambient pressure, but true half-metallic behavior is observed as pressure is increased to 100 GPa. For Co2VGa, true half-metallic to nearly half-metallic transition is observed at 40 GPa and around 100 GPa, Co2VGa shows metallic behavior. For Co2VAl, true half-metallic behavior is not observed at ambient as well as higher pressures. The half metal-to-metal transition in Co2VAl and Co2CrAl is accompanied by quenching of magnetic moment.

Easy Fabrication of Highly Thermal-Stable Cellulose Nanocrystals Using Cr(NO3)3 Catalytic Hydrolysis System: A Feasibility Study from Macro- to Nano-Dimensions

PubMed Central

Chen, You Wei; Tan, Thean Heng; Lee, Hwei Voon; Abd Hamid, Sharifah Bee

2017-01-01

This study reported on the feasibility and practicability of Cr(NO3)3 hydrolysis to isolate cellulose nanocrystals (CNCCr(NO3)3) from native cellulosic feedstock. The physicochemical properties of CNCCr(NO3)3 were compared with nanocellulose isolated using sulfuric acid hydrolysis (CNCH2SO4). In optimum hydrolysis conditions, 80 °C, 1.5 h, 0.8 M Cr(NO3)3 metal salt and solid–liquid ratio of 1:30, the CNCCr(NO3)3 exhibited a network-like long fibrous structure with the aspect ratio of 15.7, while the CNCH2SO4 showed rice-shape structure with an aspect ratio of 3.5. Additionally, Cr(NO3)3-treated CNC rendered a higher crystallinity (86.5% ± 0.3%) with high yield (83.6% ± 0.6%) as compared to the H2SO4-treated CNC (81.4% ± 0.1% and 54.7% ± 0.3%, respectively). Furthermore, better thermal stability of CNCCr(NO3)3 (344 °C) compared to CNCH2SO4 (273 °C) rendered a high potential for nanocomposite application. This comparable effectiveness of Cr(NO3)3 metal salt provides milder hydrolysis conditions for highly selective depolymerization of cellulosic fiber into value-added cellulose nanomaterial, or useful chemicals and fuels in the future. PMID:28772403

Magnetic resonance spectroscopy findings in photosensitive idiopathic generalized epilepsy.

PubMed

Aydin-Ozemir, Zeynep; Terzibasioglu, Ege; Altindag, Ebru; Sencer, Serra; Baykan, Betul

2010-01-01

Studies investigating the pathophysiology of epileptic photosensitivity indicate variable involvement of particular brain regions. Our aim was to identify metabolic differences between photosensitive idiopathic generalized epilepsy (IGE) patients and nonphotosensitive IGE patients and normal healthy subjects by using Magnetic Resonance Spectroscopy (MRS). Fourteen patients diagnosed with photosensitive IGE were investigated. The control groups consisted of 14 age- and sex-matched healthy volunteers and 14 IGE patients without photosensitivity. MRS measurements of N-acetylaspartate (NAA), choline-containing compounds (Cho), creatine (Cr) were performed in the frontal and occipital cortex and the thalamus bilaterally using a stimulated echo acquisition mode (STEAM) technique with a voxel size of 20 x 20 x 20 mm. The values of the patients with IGE were compared with those of the normal controls and within subgroups according to the clinical variables by appropriate statistical tests. Photosensitive IGE patients showed significantly decreased concentrations of NAA in the right frontal lobe and left thalamus, decreased NAA/Cr ratio in left thalamus and significantly increased concentrations of Cho/Cr ratio in the right frontal lobe and NAA/Cr in the left occipital lobe when compared to normal controls. Furthermore, left occipital NAA concentration increased and left thalamus NAA/Cr ratios were decreased from the IGE patients without photosensitivity but without reaching statistical significance. Our results support previous MR studies suggesting an asymmetrical neuronal dysfunction in favor of the dominant occipital cortex and thalamus in photosensitive IGE patients.

Distribution of 26Al in the CR chondrite chondrule-forming region of the protoplanetary disk

NASA Astrophysics Data System (ADS)

Schrader, Devin L.; Nagashima, Kazuhide; Krot, Alexander N.; Ogliore, Ryan C.; Yin, Qing-Zhu; Amelin, Yuri; Stirling, Claudine H.; Kaltenbach, Angela

2017-03-01

We report on the mineralogy, petrography, and in situ measured oxygen- and magnesium-isotope compositions of eight porphyritic chondrules (seven FeO-poor and one FeO-rich) from the Renazzo-like carbonaceous (CR) chondrites Graves Nunataks 95229, Grosvenor Mountains 03116, Pecora Escarpment 91082, and Queen Alexandra Range 99177, which experienced minor aqueous alteration and very mild thermal metamorphism. We find no evidence that these processes modified the oxygen- or Al-Mg isotope systematics of chondrules in these meteorites. Olivine, low-Ca pyroxene, and plagioclase within an individual chondrule have similar O-isotope compositions, suggesting crystallization from isotopically uniform melts. The only exceptions are relict grains in two of the chondrules; these grains are 16O-enriched relative to phenocrysts of the host chondrules. Only the FeO-rich chondrule shows a resolvable excesses of 26Mg, corresponding to an inferred initial 26Al/27Al ratio [(26Al/27Al)0] of (2.5 ± 1.6) × 10-6 (±2SE). Combining these results with the previously reported Al-Mg isotope systematics of CR chondrules (Nagashima et al., 2014, Geochem. J. 48, 561), 7 of 22 chondrules (32%) measured show resolvable excesses of 26Mg; the presence of excess 26Mg does not correlate with the FeO content of chondrule silicates. In contrast, virtually all chondrules in weakly metamorphosed (petrologic type 3.0-3.1) unequilibrated ordinary chondrites (UOCs), Ornans-like carbonaceous (CO) chondrites, and the ungrouped carbonaceous chondrite Acfer 094 show resolvable excesses of 26Mg. The inferred (26Al/27Al)0 in CR chondrules with resolvable excesses of 26Mg range from (1.0 ± 0.4) × 10-6 to (6.3 ± 0.9) × 10-6, which is typically lower than (26Al/27Al)0 in the majority of chondrules from UOCs, COs, and Acfer 094. Based on the inferred (26Al/27Al)0, three populations of CR chondrules are recognized; the population characterized by low (26Al/27Al)0 (<3 × 10-6) is dominant. There are no noticeable trends with major and minor element or O-isotope compositions between these populations. The weighted mean (26Al/27Al)0 of 22 CR chondrules measured is (1.8 ± 0.3) × 10-6. An apparent agreement between the 26Al-26Mg ages (using weighted mean value) and the revised (using 238U/235U ratio for bulk CR chondrites of 137.7789 ± 0.0085) 207Pb-206Pb age of a set of chondrules from CR chondrites (Amelin et al., 2002, Science297, 1678) is consistent with the initial 26Al/27Al ratio in the CR chondrite chondrule-forming region at the canonical level (∼5.2 × 10-5), allowing the use of 26Al-26Mg systematics as a chronometer for CR chondrules. To prove chronological significance of 26Al for CR chondrules, measurements of Al-Mg and U-Pb isotope systematics on individual chondrules are required. The presence of several generations among CR chondrules indicates some chondrules that accreted into the CR chondrite parent asteroid avoided melting by later chondrule-forming events, suggesting chondrule-forming processes may have occurred on relatively limited spatial scales. Accretion of the CR chondrite parent body occurred at >4.0-0.3+0.5 Ma after the formation of CAIs with the canonical 26Al/27Al ratio, although rapid accretion after formation of the major population of CR chondrules is not required by our data.

Experimental study on microstructure characters of foamed lightweight soil

NASA Astrophysics Data System (ADS)

Qiu, Youqiang; Li, Yongliang; Li, Meixia; Liu, Yaofu; Zhang, Liujun

2018-01-01

In order to verify the microstructure of foamed lightweight soil and its characters of compressive strength, four foamed lightweight soil samples with different water-soild ratio were selected and the microstructure characters of these samples were scanned by electron microscope. At the same time, the characters of compressive strength of foamed lightweight soil were analyzed from the microstructure. The study results show that the water-soild ratio has a prominent effect on the microstructure and compressive strength of foamed lightweight soil, with the decrease of water-solid ratio, the amount and the perforation of pores would be reduced significantly, thus eventually forming a denser and fuller interior structure. Besides, the denser microstructure and solider pore-pore wall is benefit to greatly increase mechanical intensity of foamed lightweight soil. In addition, there are very few acicular ettringite crystals in the interior of foamed lightweight soil, its number is also reduced with the decrease in water-soild ratio.

3D spatially encoded and accelerated TE-averaged echo planar spectroscopic imaging in healthy human brain.

PubMed

Iqbal, Zohaib; Wilson, Neil E; Thomas, M Albert

2016-03-01

Several different pathologies, including many neurodegenerative disorders, affect the energy metabolism of the brain. Glutamate, a neurotransmitter in the brain, can be used as a biomarker to monitor these metabolic processes. One method that is capable of quantifying glutamate concentration reliably in several regions of the brain is TE-averaged (1) H spectroscopic imaging. However, this type of method requires the acquisition of multiple TE lines, resulting in long scan durations. The goal of this experiment was to use non-uniform sampling, compressed sensing reconstruction and an echo planar readout gradient to reduce the scan time by a factor of eight to acquire TE-averaged spectra in three spatial dimensions. Simulation of glutamate and glutamine showed that the 2.2-2.4 ppm spectral region contained 95% glutamate signal using the TE-averaged method. Peak integration of this spectral range and home-developed, prior-knowledge-based fitting were used for quantitation. Gray matter brain phantom measurements were acquired on a Siemens 3 T Trio scanner. Non-uniform sampling was applied retrospectively to these phantom measurements and quantitative results of glutamate with respect to creatine 3.0 (Glu/Cr) ratios showed a coefficient of variance of 16% for peak integration and 9% for peak fitting using eight-fold acceleration. In vivo scans of the human brain were acquired as well and five different brain regions were quantified using the prior-knowledge-based algorithm. Glu/Cr ratios from these regions agreed with previously reported results in the literature. The method described here, called accelerated TE-averaged echo planar spectroscopic imaging (TEA-EPSI), is a significant methodological advancement and may be a useful tool for categorizing glutamate changes in pathologies where affected brain regions are not known a priori. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Compressive Sensing of Foot Gait Signals and Its Application for the Estimation of Clinically Relevant Time Series.

PubMed

Pant, Jeevan K; Krishnan, Sridhar

2016-07-01

A new signal reconstruction algorithm for compressive sensing based on the minimization of a pseudonorm which promotes block-sparse structure on the first-order difference of the signal is proposed. Involved optimization is carried out by using a sequential version of Fletcher-Reeves' conjugate-gradient algorithm, and the line search is based on Banach's fixed-point theorem. The algorithm is suitable for the reconstruction of foot gait signals which admit block-sparse structure on the first-order difference. An additional algorithm for the estimation of stride-interval, swing-interval, and stance-interval time series from the reconstructed foot gait signals is also proposed. This algorithm is based on finding zero crossing indices of the foot gait signal and using the resulting indices for the computation of time series. Extensive simulation results demonstrate that the proposed signal reconstruction algorithm yields improved signal-to-noise ratio and requires significantly reduced computational effort relative to several competing algorithms over a wide range of compression ratio. For a compression ratio in the range from 88% to 94%, the proposed algorithm is found to offer improved accuracy for the estimation of clinically relevant time-series parameters, namely, the mean value, variance, and spectral index of stride-interval, stance-interval, and swing-interval time series, relative to its nearest competitor algorithm. The improvement in performance for compression ratio as high as 94% indicates that the proposed algorithms would be useful for designing compressive sensing-based systems for long-term telemonitoring of human gait signals.

Non-linear properties of metallic cellular materials with a negative Poisson's ratio

NASA Technical Reports Server (NTRS)

Choi, J. B.; Lakes, R. S.

1992-01-01

Negative Poisson's ratio copper foam was prepared and characterized experimentally. The transformation into re-entrant foam was accomplished by applying sequential permanent compressions above the yield point to achieve a triaxial compression. The Poisson's ratio of the re-entrant foam depended on strain and attained a relative minimum at strains near zero. Poisson's ratio as small as -0.8 was achieved. The strain dependence of properties occurred over a narrower range of strain than in the polymer foams studied earlier. Annealing of the foam resulted in a slightly greater magnitude of negative Poisson's ratio and greater toughness at the expense of a decrease in the Young's modulus.

A Lossless Multichannel Bio-Signal Compression Based on Low-Complexity Joint Coding Scheme for Portable Medical Devices

PubMed Central

Kim, Dong-Sun; Kwon, Jin-San

2014-01-01

Research on real-time health systems have received great attention during recent years and the needs of high-quality personal multichannel medical signal compression for personal medical product applications are increasing. The international MPEG-4 audio lossless coding (ALS) standard supports a joint channel-coding scheme for improving compression performance of multichannel signals and it is very efficient compression method for multi-channel biosignals. However, the computational complexity of such a multichannel coding scheme is significantly greater than that of other lossless audio encoders. In this paper, we present a multichannel hardware encoder based on a low-complexity joint-coding technique and shared multiplier scheme for portable devices. A joint-coding decision method and a reference channel selection scheme are modified for a low-complexity joint coder. The proposed joint coding decision method determines the optimized joint-coding operation based on the relationship between the cross correlation of residual signals and the compression ratio. The reference channel selection is designed to select a channel for the entropy coding of the joint coding. The hardware encoder operates at a 40 MHz clock frequency and supports two-channel parallel encoding for the multichannel monitoring system. Experimental results show that the compression ratio increases by 0.06%, whereas the computational complexity decreases by 20.72% compared to the MPEG-4 ALS reference software encoder. In addition, the compression ratio increases by about 11.92%, compared to the single channel based bio-signal lossless data compressor. PMID:25237900

Optimal Compressed Sensing and Reconstruction of Unstructured Mesh Datasets

DOE PAGES

Salloum, Maher; Fabian, Nathan D.; Hensinger, David M.; ...

2017-08-09

Exascale computing promises quantities of data too large to efficiently store and transfer across networks in order to be able to analyze and visualize the results. We investigate compressed sensing (CS) as an in situ method to reduce the size of the data as it is being generated during a large-scale simulation. CS works by sampling the data on the computational cluster within an alternative function space such as wavelet bases and then reconstructing back to the original space on visualization platforms. While much work has gone into exploring CS on structured datasets, such as image data, we investigate itsmore » usefulness for point clouds such as unstructured mesh datasets often found in finite element simulations. We sample using a technique that exhibits low coherence with tree wavelets found to be suitable for point clouds. We reconstruct using the stagewise orthogonal matching pursuit algorithm that we improved to facilitate automated use in batch jobs. We analyze the achievable compression ratios and the quality and accuracy of reconstructed results at each compression ratio. In the considered case studies, we are able to achieve compression ratios up to two orders of magnitude with reasonable reconstruction accuracy and minimal visual deterioration in the data. Finally, our results suggest that, compared to other compression techniques, CS is attractive in cases where the compression overhead has to be minimized and where the reconstruction cost is not a significant concern.« less

Significant Axial Elongation with Minimal Change in Refraction in 3- to 6-Year-Old Chinese Preschoolers: The Shenzhen Kindergarten Eye Study.

PubMed

Guo, Xinxing; Fu, Min; Ding, Xiaohu; Morgan, Ian G; Zeng, Yangfa; He, Mingguang

2017-12-01

To document the distribution of ocular biometry and to evaluate its associations with refraction in a group of Chinese preschoolers. Population-based cross-sectional study. A total of 1133 preschoolers 3 to 6 years of age from 8 representative kindergartens. Biometric measurements including axial length (AL), anterior chamber depth (ACD), and corneal radius of curvature (CR) were obtained from partial-coherence laser interferometry (IOL Master; Carl Zeiss Meditec, Oberkochen, Germany) before cycloplegia. Lens power (LP) and AL-to-CR ratio were calculated. Cycloplegic refraction (3 drops of 1% cyclopentolate) was measured using an autorefractor (KR8800; Topcon Corp., Tokyo, Japan), and spherical equivalent refraction (SER) was calculated. Biometric and refractive parameters were assessed as a function of age and gender. Multiple regression analysis was performed to explore the associations between refraction and ocular biometry. Ocular biometric distributions and their relationships to refraction. Among the 1127 children (99.5%) with successful cycloplegic refraction, mean SER was 1.37±0.63 diopters (D). Prevalence of myopia increased from 0% at 3 years of age to 3.7% (95% confidence interval, 1.0%-6.5%) at 6 years of age. Biometric parameters followed Gaussian distributions with means of 22.39±0.68 mm for AL, 7.79±0.25 mm for CR, and 24.61±1.42 D for calculated LP; and non-Gaussian distributions with means of 3.34±0.24 mm for ACD and 2.88±0.06 for AL-to-CR ratio. Axial length, ACD, and AL-to-CR ratio increased from 3 to 6 years of age, CR remained stable, whereas LP declined. Overall, SER declined slightly. For the SER variance, AL explained 18.6% and AL-to-CR ratio explained 39.8%, whereas AL, CR, and LP accounted for 80.0% after adjusting for age and gender. Young Chinese children are predominantly mildly hyperopic, with a low prevalence of myopia by the age of 6 years. An increase of 1 mm in AL was associated with only 0.45 D of myopic change. Decreases in LP reduce the myopic shifts that normally would be associated with increases in AL, and thus play a key role in refractive development in this age group. Copyright © 2017 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Nature of the impactor at the K/T boundary: clues from Os, W and Cr isotopes.

NASA Astrophysics Data System (ADS)

Quitté, G.; Robin, E.; Capmas, F.; Levasseur, S.; Rocchia, R.; Birck, J. L.; Allègre, C. J.

2003-04-01

We measured the isotope composition of Os, W and Cr in K/T boundary sediments of three marine sites (Stevns Klint, Caravaca and Bidart) to determine the nature of the bolid that impacted the Earth 65 Myrs ago. We also analysed Ni-rich cosmic spinels, because they are thought to keep the signature of the impactor. The low REE content in spinels precludes indeed the hypothesis of a mixing with more than 10% of terrestrial material. The Os and W enrichment at the K/T boundary could be explained by a scavenging of chalcophile elements at the time of sulfide precipitation. The 187Os/186Os ratio of the K/T sediments is higher than the ratio of any kind of meteorites. On top of a possible mixing with surrounding sediments, we suggest that the boundary contained more Re in the past (lost since that time by alteration and oxidation) and that the Os isotope ratio is in fact disturbed. On each of the three sites, the boundary itself does not present any tungsten isotopic anomaly. The most likely interpretation is that the extraterrestrial material is diluted enough into the sediments so that the isotopic signature has been erased. Spinels show a small deficit of (0.34±0.9) ɛ in 182W. The large error bar precludes any clear conclusion whether or not a meteoritic signature is really present. If the spinels really carry an extraterrestrial signature as expected, their W composition is in favour of an ordinary chondrite. All K/T samples (sediments and spinels) are apparently depleted in 53Cr by about 0.5 ɛ (after renormalization of 54Cr to the terrestrial value) whereas ordinary chondrites display an excess of about 0.5 ɛ. Among meteorites, only carbonaceous chondrites present a negative value for the 53Cr/52Cr ratio relative to the terrestrial value. As more than 90% of the Cr present in spinels is of extraterrestrial origin, the Cr isotopes unambiguously show that the K/T impactor was a carbonaceous chondrite. These isotopic results also confirm the extraterrestrial origin of spinels. The W isotope composition of the spinels does not fully agree with the conclusion of a carbonaceous chondrite, but a refined measurement is required to discuss this discrepancy in more details.

Finite element analysis of residual stress in cold expanded plate with different thickness and expansion ratio

NASA Astrophysics Data System (ADS)

Arifin Shariffudin, Kamarul; Karuppanan, Saravanan; Patil, Santosh S.

2017-10-01

Cold expansion of fastener/rivet holes is a common way to generate beneficial compressive residual stress around the fastener hole. In this study, cold expansion process was simulated by finite-element method in order to determine the residual stress field around two cold expanded holes by varying the plate thickness and expansion ratio of the hole. The model was developed in ANSYS and assigned to aluminium alloy 7475-T61 material model. The results showed that the residual stress become more compressive as the plate thickness is increased up to t/d = 2.6 and decreased for further level of thickness. In addition, the residual stress at the edge of the hole become more compressive as the expansion ratio is increased up to 4.5% and decreased for further level of expansion. This study also found that the residual stresses near the entrance and the exit face of the plate are less compressive than the residual stresses on the mid-thickness of the plate.

Effect of Si Content on Oxide Formation on Surface of Molten Fe-Cr-C Alloy Bath During Oxygen Top Blowing

NASA Astrophysics Data System (ADS)

Mihara, Ryosuke; Gao, Xu; Kim, Sun-joong; Ueda, Shigeru; Shibata, Hiroyuki; Seok, Min Oh; Kitamura, Shin-ya

2018-02-01

Using a direct observation experimental method, the oxide formation behavior on the surface of Fe-Cr-5 mass pct C-Si alloy baths during decarburization by a top-blown Ar-O2 mixture was studied. The effects of the initial Si and Cr content of the alloy, temperature, and oxygen feed ratio on oxide formation were investigated. The results showed that, for alloys without Si, oxide particles, unstable oxide films, and stable oxide films formed sequentially. The presence of Si in the alloy changed the formation behavior of stable oxide film, and increased the crucial C content when stable oxide film started to form. Increasing the temperature, decreasing the initial Cr content, and increasing the ratio of the diluting gas decreased the critical C content at which a stable oxide film started to form. In addition, the P CO and a_{{{Cr}2 {O}3 }} values at which oxides started to form were estimated using Hilty's equation and the equilibrium relation to understand the formation conditions and the role of each parameter in oxide formation.

3D Simulations of NIF Wetted Foam Experiments to Understand the Transition from 2D to 3D Implosion Behavior

NASA Astrophysics Data System (ADS)

Haines, Brian; Olson, Richard; Yi, Austin; Zylstra, Alex; Peterson, Robert; Bradley, Paul; Shah, Rahul; Wilson, Doug; Kline, John; Leeper, Ramon; Batha, Steve

2017-10-01

The high convergence ratio (CR) of layered Inertial Confinement Fusion capsule implosions contribute to high performance in 1D simulations yet make them more susceptible to hydrodynamic instabilities, contributing to the development of 3D flows. The wetted foam platform is an approach to hot spot ignition to achieve low-to-moderate convergence ratios in layered implosions on the NIF unobtainable using an ice layer. Detailed high-resolution modeling of these experiments in 2D and 3D, including all known asymmetries, demonstrates that 2D hydrodynamics explain capsule performance at CR 12 but become less suitable as the CR increases. Mechanisms for this behavior and detailed comparisons of simulations to experiments on NIF will be presented. To evaluate the tradeoff between increased instability and improved 1D performance, we present a full-scale wetted foam capsule design with 17

Immobilization of radioactive and hazardous wastes in a developed sulfur polymer cement (SPC) matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagdy, M.; Azim, Abdel; El-Gammal, Belal

Available in abstract form only. Full text of publication follows: A process has been developed for the immobilization Cs, Sr, Ce, Pb, and Cr in forms that is non-dispersible and could be safely immobilized. The simulated radioactive wastes of Cs, Sr, and Ce, and the hazardous wastes of Cr, and Pb were immobilized in the stable form of sulfur polymer cement (SPC). In this process, the contaminants (in a single form) were added to the sulfur mixture of sulfur and aromatic /or aliphatic hydrocarbons that used as polymerizing agents for sulfur (95% S, and 5% organic polymer by weight). Durabilitymore » of the fabricated SPC matrices was assessed in terms of their water of immersion, porosity, and compressive strength. The water immersion, and open porosity were found to be less than 2.5% for all the prepared matrices, whereas the compressive strength was in the range between 62.4 and 142.3 Kg.cm{sup -2}, depending on the composition of the prepared matrix. The prepared SPC matrices that characterized by X-ray diffraction (XRD) showed that the different added contaminants were stabilized during the solidification process during their reaction with sulfur and the organic polymer to form the corresponding metal sulfides. Toxicity Characteristic Leaching Procedure (TCLP), and the IAEA standard method have assessed the leachability of the prepared waste matrices. The TCLP results showed that most the concentration of the contaminants released were under their detection limit. The leach index for the investigated metals from the prepared SPC matrices was in the range of 9-11. The order of release of the investigated metals was Sr>Cs>Pb>Cr>Ce for the aliphatic polymer, and Sr>Cr>Pb>Cs>Ce for the aromatic one. The results obtained revealed a high performance for the prepared SPC matrices, as they are of low cost effect, highly available materials, and possessed good mechanical and leaching properties. Key Words: SPC/ Matrices/ Immobilization/ Wastes/ Leachability. (authors)« less

Microstructure and hot corrosion behavior of the Ni-based superalloy GH202 treated by laser shock processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Jiangdong

The effects of laser shock processing on microstructure, the residual stress, and hot corrosion behavior of the Ni-based superalloy GH202 were investigated. The microstructures of GH202 before and after laser shock processing (LSP) were characterized by electron backscattered diffraction (EBSD) and transmission electron microscope (TEM). A large number of crystal defects (twins, dislocation arrays, and high dense tangles) were generated on the surface of GH202 treated with LSP. The cross-sectional compressive residual stress and micro-hardness of specimens treated by LSP were improved significantly. The corrosion kinetics of GH202 with or without LSP treatment at 800 °C and 900 °C weremore » investigated. Analysis by X-ray diffraction (XRD) revealed that the corrosion products mainly consist of Cr{sub 2}O{sub 3}, TiO{sub 2}, Al{sub 2}O{sub 3}, NiO, CrS, Ni{sub 3}S{sub 2}, and Na{sub 2}CrO{sub 4}. The surface and cross-section morphologies were observed by scanning electron microscope (SEM) combined with energy dispersive spectroscopy (EDS). The results confirmed that the crystal defects induced by LSP promotes the creation of diffusion paths for elements (Cr, Al, and Ti), allowing the formation of tiny homogeneous oxidation films in a very short time. Additionally, the spallation of oxidation film on the treated specimens was alleviated significantly. Overall, the hot corrosion resistance of Ni-based GH202 induced by LSP was improved in Na{sub 2}SO{sub 4} and NaCl molten salt from 800 °C to 900 °C. - Highlights: • Microstructure changes of GH202 before and after LSP were observed by EBSD and TEM. • The hardness and residual compressive stress after LSP were significantly increased. • The increased diffusion paths for elements helped to form oxidation films quickly. • Hot corrosion resistance of GH202 after LSP was significantly improved.« less

Long-term osseointegration of 3D printed CoCr constructs with an interconnected open-pore architecture prepared by electron beam melting.

PubMed

Shah, Furqan A; Omar, Omar; Suska, Felicia; Snis, Anders; Matic, Aleksandar; Emanuelsson, Lena; Norlindh, Birgitta; Lausmaa, Jukka; Thomsen, Peter; Palmquist, Anders

2016-05-01

In orthopaedic surgery, cobalt chromium (CoCr) based alloys are used extensively for their high strength and wear properties, but with concerns over stress shielding and bone resorption due to the high stiffness of CoCr. The structural stiffness, principally related to the bulk and the elastic modulus of the material, may be lowered by appropriate design modifications, to reduce the stiffness mismatch between metal/alloy implants and the adjacent bone. Here, 3D printed CoCr and Ti6Al4V implants of similar macro-geometry and interconnected open-pore architecture prepared by electron beam melting (EBM) were evaluated following 26week implantation in adult sheep femora. Despite higher total bone-implant contact for Ti6Al4V (39±4%) than CoCr (27±4%), bone formation patterns were similar, e.g., densification around the implant, and gradual ingrowth into the porous network, with more bone in the outer half (periphery) than the inner half (centre). Raman spectroscopy revealed no major differences in mineral crystallinity, the apatite-to-collagen ratio, or the carbonate-to-phosphate ratio. Energy dispersive X-ray spectroscopy showed similar Ca/P ratio of the interfacial tissue adjacent to both materials. Osteocytes made direct contact with CoCr and Ti6Al4V. While osteocyte density and distribution in the new-formed bone were largely similar for the two alloys, higher osteocyte density was observed at the periphery of the porous network for CoCr, attributable to slower remodelling and a different biomechanical environment. The results demonstrate the possibility to achieve bone ingrowth into open-pore CoCr constructs, and attest to the potential for fabricating customised osseointegrated CoCr implants for load-bearing applications. Although cobalt chromium (CoCr) based alloys are used extensively in orthopaedic surgery, stress shielding due to the high stiffness of CoCr is of concern. To reduce the stiffness mismatch between CoCr and bone, CoCr and Ti6Al4V implants having an interconnected open-pore architecture were prepared by electron beam melting (EBM). After six months of submerged healing in sheep, both alloys showed similar patterns of bone formation, with densification around the implant and gradual ingrowth into the porous network. The molecular and elemental composition of the interfacial tissue was similar for both alloys. Osteocytes made direct contact with both alloys, with similar overall osteocyte density and distribution. The work attests to the potential for achieving osseointegration of EBM manufactured porous CoCr implants. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Performance of a Space-Based Wavelet Compressor for Plasma Count Data on the MMS Fast Plasma Investigation

NASA Technical Reports Server (NTRS)

Barrie, A. C.; Smith, S. E.; Dorelli, J. C.; Gershman, D. J.; Yeh, P.; Schiff, C.; Avanov, L. A.

2017-01-01

Data compression has been a staple of imaging instruments for years. Recently, plasma measurements have utilized compression with relatively low compression ratios. The Fast Plasma Investigation (FPI) on board the Magnetospheric Multiscale (MMS) mission generates data roughly 100 times faster than previous plasma instruments, requiring a higher compression ratio to fit within the telemetry allocation. This study investigates the performance of a space-based compression standard employing a Discrete Wavelet Transform and a Bit Plane Encoder (DWT/BPE) in compressing FPI plasma count data. Data from the first 6 months of FPI operation are analyzed to explore the error modes evident in the data and how to adapt to them. While approximately half of the Dual Electron Spectrometer (DES) maps had some level of loss, it was found that there is little effect on the plasma moments and that errors present in individual sky maps are typically minor. The majority of Dual Ion Spectrometer burst sky maps compressed in a lossless fashion, with no error introduced during compression. Because of induced compression error, the size limit for DES burst images has been increased for Phase 1B. Additionally, it was found that the floating point compression mode yielded better results when images have significant compression error, leading to floating point mode being used for the fast survey mode of operation for Phase 1B. Despite the suggested tweaks, it was found that wavelet-based compression, and a DWT/BPE algorithm in particular, is highly suitable to data compression for plasma measurement instruments and can be recommended for future missions.

Navy Electroplating Pollution Control Technology Assessment Manual.

DTIC Science & Technology

1984-02-01

quality. Dummying of chromium baths is used in the special case where high cathode-to-anode 5ea ratio has resulted in build up of trivalent chromium (Cr...Dummying with a high anode -to-cat hode area ratio can be 6used to reoxidize the trivalent to hexavalent chromium (Cr ).Proper scheduling of work can...unit processes: * Chromium reduction (if needed) of segregated chromium waste streams to reduce the chromium from its hexavalent form to the trivalent

Effects of MC-Type Carbide Forming and Graphitizing Elements on Thermal Fatigue Behavior of Indefinite Chilled Cast Iron Rolls

NASA Astrophysics Data System (ADS)

Ahiale, Godwin Kwame; Choi, Won-Doo; Suh, Yongchan; Lee, Young-Kook; Oh, Yong-Jun

2015-11-01

The thermal fatigue behavior of indefinite chilled cast iron rolls with various V+Nb contents and Si/Cr ratios was evaluated. Increasing the ratio of Si/Cr prolonged the life of the rolls by reducing brittle cementites. Higher V+Nb addition also increased the life through the formation of carbides that refined and toughened the martensite matrix and reduced the thermal expansion mismatch in the microstructure.

High-precision Q EC values of superallowed 0 + → 0 + β-emitters 46Cr, 50Fe and 54Ni

DOE PAGES

Zhang, P.; Xu, X.; Shuai, P.; ...

2017-01-23

Short-lived 46Cr, 50Fe and 54Ni were studied by isochronous mass spectrometry at the HIRFL-CSR facility in Lanzhou. The measured precision mass excesses (ME) of 46Cr, 50Fe and 54Ni are -29471(11) keV, -34477(6) keV and -39278(4) keV, respectively. The superallowed 0 +→0+β-decay Q values were derived to be Q EC( 46Cr) =7604(11) keV, Q EC( 50Fe) =8150(6) keV and Q EC( 54Ni) =8731(4) keV. The values for 50Fe and 54Ni are by one order of magnitude more precise than the adopted literature values. By combining the existing half-lives and branching ratios, we obtained the corrected ℱt values to be ℱt(more » 50Fe) =3103(70) s and ℱt( 54Ni) =3076(50) s. The main contribution to the ℱt uncertainties is now due to β-decay branching ratios, still, more high-precision measurements of the half-lives, the masses, and especially the branching ratios are needed in order to satisfy the requirements for a stringent CVC test.« less

High-precision Q EC values of superallowed 0 + → 0 + β-emitters 46Cr, 50Fe and 54Ni

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, P.; Xu, X.; Shuai, P.

Short-lived 46Cr, 50Fe and 54Ni were studied by isochronous mass spectrometry at the HIRFL-CSR facility in Lanzhou. The measured precision mass excesses (ME) of 46Cr, 50Fe and 54Ni are -29471(11) keV, -34477(6) keV and -39278(4) keV, respectively. The superallowed 0 +→0+β-decay Q values were derived to be Q EC( 46Cr) =7604(11) keV, Q EC( 50Fe) =8150(6) keV and Q EC( 54Ni) =8731(4) keV. The values for 50Fe and 54Ni are by one order of magnitude more precise than the adopted literature values. By combining the existing half-lives and branching ratios, we obtained the corrected ℱt values to be ℱt(more » 50Fe) =3103(70) s and ℱt( 54Ni) =3076(50) s. The main contribution to the ℱt uncertainties is now due to β-decay branching ratios, still, more high-precision measurements of the half-lives, the masses, and especially the branching ratios are needed in order to satisfy the requirements for a stringent CVC test.« less

Estimation of excess energies and activity coefficients for the penternary Ni-Cr-Co-Al-Mo system and its subsystems

NASA Astrophysics Data System (ADS)

Dogan, A.; Arslan, H.; Dogan, T.

2015-06-01

Using different prediction methods, such as the General Solution Model of Kohler and Muggianu, the excess energy and activities of molybdenum for the sections of the phase diagram for the penternary Ni-Cr-Co-Al-Mo system with mole ratios xNi/ xMo = 1, xCr/ xMo = 1, xCo/ xMo = 1, and xAl/ xMo = r = 0.5 and 1, were thermodynamically investigated at a temperature of 2000 K, whereas the excess energy and activities of Bi for the section corresponding to the ternary Bi-Ga-Sb system with mole ratio xGa/ xSb = 1/9 were thermodynamically investigated at a temperature of 1073 K. In the case of r = 0.5 and 1 in the alloys Ni-Cr-Co-Al-Mo, a positive deviation in the activity coefficient was revealed, as molybdenum content increased. Moreover, in the calculations performed in Chou's GSM model, the obtained values for excess Gibbs energies are negative in the whole concentration range of bismuth at 1073 K and exhibit the minimum of about -2.2 kJ/mol at the mole ratio xGa/ xSb = 1/9 in the alloy Bi-Ga-Sb.

Optical diagnostics with radiation trapping effect in low density and low temperature helium plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Wonwook, E-mail: wwlee@kaeri.re.kr; Kwon, Duck-Hee; Park, Kyungdeuk

2016-06-15

Low density (n{sub e} < 10{sup 11 }cm{sup −3}) and low temperature (T{sub e} < 10 eV) helium plasma was generated by hot filament discharge. Electron temperature and density of neutral helium plasma were measured by Langmuir probe and were determined by line intensity ratio method using optical emission spectroscopy with population modelings. Simple corona model and collisional-radiative (CR) model without consideration for radiation trapping effect are applied. In addition, CR model taking into account the radiation trapping effect (RTE) is adopted. The change of single line intensity ratio as a function of electron temperature and density were investigated when the RTE is included and excluded.more » The changes of multi line intensity ratios as a function of electron temperature were scanned for various radiative-excitation rate coefficients from the ground state and the helium gas pressures related with the RTE. Our CR modeling with RTE results in fairly better agreement of the spectroscopic diagnostics for the plasma temperature or density with the Langmuir probe measurements for various helium gas pressures than corona modeling and CR modeling without RTE.« less

An optimally evolved connective ratio of neural networks that maximizes the occurrence of synchronized bursting behavior

PubMed Central

2012-01-01

Background Synchronized bursting activity (SBA) is a remarkable dynamical behavior in both ex vivo and in vivo neural networks. Investigations of the underlying structural characteristics associated with SBA are crucial to understanding the system-level regulatory mechanism of neural network behaviors. Results In this study, artificial pulsed neural networks were established using spike response models to capture fundamental dynamics of large scale ex vivo cortical networks. Network simulations with synaptic parameter perturbations showed the following two findings. (i) In a network with an excitatory ratio (ER) of 80-90%, its connective ratio (CR) was within a range of 10-30% when the occurrence of SBA reached the highest expectation. This result was consistent with the experimental observation in ex vivo neuronal networks, which were reported to possess a matured inhibitory synaptic ratio of 10-20% and a CR of 10-30%. (ii) No SBA occurred when a network does not contain any all-positive-interaction feedback loop (APFL) motif. In a neural network containing APFLs, the number of APFLs presented an optimal range corresponding to the maximal occurrence of SBA, which was very similar to the optimal CR. Conclusions In a neural network, the evolutionarily selected CR (10-30%) optimizes the occurrence of SBA, and APFL serves a pivotal network motif required to maximize the occurrence of SBA. PMID:22462685

The relationship between Vickers microhardness and compressive strength of functional surface geopolymers

NASA Astrophysics Data System (ADS)

Subaer, Ekaputri, Januari Jaya; Fansuri, Hamzah; Abdullah, Mustafa Al Bakri

2017-09-01

An experimental study to investigate the relationship between Vickers microhardness and compressive strength of geopolymers made from metakaolin has been conducted. Samples were prepared by using metakaolin activated with a sodium silicate solution at a different ratio of Si to Al and Na to Al and cured at 70°C for one hour. The resulting geopolymers were stored in an open air for 28 days before conducting any measurement. Bulk density and apparent porosity of the samples were measured by using Archimedes's method. Vickers microhardness measurements were performed on a polished surface of geopolymers with a load ranging from 0.3 - 1.0 kg. The topographic of indented samples were examined by using scanning electron microscopy (SEM). Compressive strength of the resulting geopolymers was measured on the cylindrical samples with a ratio of height to the diameter was 2:1. The results showed that the molar ratios of geopolymers compositions play important roles in the magnitude of bulk density, porosity, Vickers's microhardness as well as the compressive strength. The porosity reduced exponentially the magnitude of the strength of geopolymers. It was found that the relationship between Vickers microhardness and compressive strength was linear.

Universal data compression

NASA Astrophysics Data System (ADS)

Lindsay, R. A.; Cox, B. V.

Universal and adaptive data compression techniques have the capability to globally compress all types of data without loss of information but have the disadvantage of complexity and computation speed. Advances in hardware speed and the reduction of computational costs have made universal data compression feasible. Implementations of the Adaptive Huffman and Lempel-Ziv compression algorithms are evaluated for performance. Compression ratios versus run times for different size data files are graphically presented and discussed in the paper. Required adjustments needed for optimum performance of the algorithms relative to theoretical achievable limits will be outlined.

An Optimal Seed Based Compression Algorithm for DNA Sequences

PubMed Central

Gopalakrishnan, Gopakumar; Karunakaran, Muralikrishnan

2016-01-01

This paper proposes a seed based lossless compression algorithm to compress a DNA sequence which uses a substitution method that is similar to the LempelZiv compression scheme. The proposed method exploits the repetition structures that are inherent in DNA sequences by creating an offline dictionary which contains all such repeats along with the details of mismatches. By ensuring that only promising mismatches are allowed, the method achieves a compression ratio that is at par or better than the existing lossless DNA sequence compression algorithms. PMID:27555868

Lossless compression of otoneurological eye movement signals.

PubMed

Tossavainen, Timo; Juhola, Martti

2002-12-01

We studied the performance of several lossless compression algorithms on eye movement signals recorded in otoneurological balance and other physiological laboratories. Despite the wide use of these signals their compression has not been studied prior to our research. The compression methods were based on the common model of using a predictor to decorrelate the input and using an entropy coder to encode the residual. We found that these eye movement signals recorded at 400 Hz and with 13 bit amplitude resolution could losslessly be compressed with a compression ratio of about 2.7.

Predicting the outcome of grade II glioma treated with temozolomide using proton magnetic resonance spectroscopy.

PubMed

Guillevin, R; Menuel, C; Taillibert, S; Capelle, L; Costalat, R; Abud, L; Habas, C; De Marco, G; Hoang-Xuan, K; Chiras, J; Vallée, J-N

2011-06-07

This study was designed to evaluate proton magnetic resonance spectroscopy ((1)H-MRS) for monitoring the WHO grade II glioma (low-grade glioma (LGG)) treated with temozolomide (TMZ). This prospective study included adult patients with progressive LGG that was confirmed by magnetic resonance imaging (MRI). Temozolomide was administered at every 28 days. Response to TMZ was evaluated by monthly MRI examinations that included MRI with volumetric calculations and (1)H-MRS for assessing Cho/Cr and Cho/NAA ratios. Univariate, multivariate and receiver-operating characteristic statistical analyses were performed on the results. A total of 21 LGGs from 31 patients were included in the study, and followed for at least n=14 months during treatment. A total of 18 (86%) patients experienced a decrease in tumour volume with a greater decrease of metabolic ratios. Subsequently, five (28%) of these tumours resumed growth despite the continuation of TMZ administration with an earlier increase of metabolic ratios of 2 months. Three (14%) patients did not show any volume or metabolic change. The evolutions of the metabolic ratios, mean(Cho/Cr)(n) and mean(Cho/NAA)(n), were significantly correlated over time (Spearman ρ=+0.95) and followed a logarithmic regression (P>0.001). The evolutions over time of metabolic ratios, mean(Cho/Cr)(n) and mean(Cho/NAA)(n), were significantly correlated with the evolution of the mean relative decrease of tumour volume, mean(ΔV(n)/V(o)), according to a linear regression (P<0.001) in the 'response/no relapse' patient group, and with the evolution of the mean tumour volume (meanV(n)), according to an exponential regression (P<0.001) in the 'response/relapse' patient group. The mean relative decrease of metabolic ratio, mean(Δ(Cho/Cr)(n)/(Cho/Cr)(o)), at n=3 months was predictive of tumour response over the 14 months of follow-up. The mean relative change between metabolic ratios, mean((Cho/NAA)(n)-(Cho/Cr)(n))/(Cho/NAA)(n), at n=4 months was predictive of tumour relapse with a significant cutoff of 0.046, a sensitivity of 60% and a specificity of 100% (P=0.004). The (1)H-MRS profile changes more widely and rapidly than tumour volume during the response and relapse phases, and represents an early predictive factor of outcome over 14 months of follow-up. Thus, (1)H-MRS may be a promising, non-invasive tool for predicting and monitoring the clinical response to TMZ.

Predicting the outcome of grade II glioma treated with temozolomide using proton magnetic resonance spectroscopy

PubMed Central

Guillevin, R; Menuel, C; Taillibert, S; Capelle, L; Costalat, R; Abud, L; Habas, C; De Marco, G; Hoang-Xuan, K; Chiras, J; Vallée, J-N

2011-01-01

Background: This study was designed to evaluate proton magnetic resonance spectroscopy (1H-MRS) for monitoring the WHO grade II glioma (low-grade glioma (LGG)) treated with temozolomide (TMZ). Methods: This prospective study included adult patients with progressive LGG that was confirmed by magnetic resonance imaging (MRI). Temozolomide was administered at every 28 days. Response to TMZ was evaluated by monthly MRI examinations that included MRI with volumetric calculations and 1H-MRS for assessing Cho/Cr and Cho/NAA ratios. Univariate, multivariate and receiver-operating characteristic statistical analyses were performed on the results. Results: A total of 21 LGGs from 31 patients were included in the study, and followed for at least n=14 months during treatment. A total of 18 (86%) patients experienced a decrease in tumour volume with a greater decrease of metabolic ratios. Subsequently, five (28%) of these tumours resumed growth despite the continuation of TMZ administration with an earlier increase of metabolic ratios of 2 months. Three (14%) patients did not show any volume or metabolic change. The evolutions of the metabolic ratios, mean(Cho/Cr)n and mean(Cho/NAA)n, were significantly correlated over time (Spearman ρ=+0.95) and followed a logarithmic regression (P>0.001). The evolutions over time of metabolic ratios, mean(Cho/Cr)n and mean(Cho/NAA)n, were significantly correlated with the evolution of the mean relative decrease of tumour volume, mean(ΔVn/Vo), according to a linear regression (P<0.001) in the ‘response/no relapse' patient group, and with the evolution of the mean tumour volume (meanVn), according to an exponential regression (P<0.001) in the ‘response/relapse' patient group. The mean relative decrease of metabolic ratio, mean(Δ(Cho/Cr)n/(Cho/Cr)o), at n=3 months was predictive of tumour response over the 14 months of follow-up. The mean relative change between metabolic ratios, mean((Cho/NAA)n−(Cho/Cr)n)/(Cho/NAA)n, at n=4 months was predictive of tumour relapse with a significant cutoff of 0.046, a sensitivity of 60% and a specificity of 100% (P=0.004). Conclusions: The 1H-MRS profile changes more widely and rapidly than tumour volume during the response and relapse phases, and represents an early predictive factor of outcome over 14 months of follow-up. Thus, 1H-MRS may be a promising, non-invasive tool for predicting and monitoring the clinical response to TMZ. PMID:21610707

Application of a protocol for magnetic resonance spectroscopy of adrenal glands: an experiment with over 100 cases.

PubMed

Melo, Homero José de Farias E; Goldman, Suzan M; Szejnfeld, Jacob; Faria, Juliano F; Huayllas, Martha K P; Andreoni, Cássio; Kater, Cláudio E

2014-01-01

To evaluate a protocol for two-dimensional (2D) hydrogen proton (1H) magnetic resonance spectroscopy (MRS) (Siemens Medical Systems; Erlangen, Germany) in the detection of adrenal nodules and differentiation between benign and malignant masses (adenomas, pheochromocytomas, carcinomas and metastases). A total of 118 patients (36 men; 82 women) (mean age: 57.3 ± 13.3 years) presenting with 138 adrenal nodules/masses were prospectively assessed. A multivoxel system was utilized with a 2D point-resolved spectroscopy/chemical shift imaging sequence. The following ratios were calculated: choline (Cho)/creatine (Cr), 4.0-4.3/Cr, lipid (Lip)/Cr, Cho/Lip and lactate (Lac)/Cr. 2D-1H-MRS was successful in 123 (89.13%) lesions. Sensitivity and specificity values observed for the ratios and cutoff points were the following: Cho/Cr ≥ 1.2, 100% sensitivity, 98.2% specificity (differences between adenomas/pheochromocytomas and carcinomas/ metastases); 4.0-4.3 ppm/Cr ≥ 1.5, 92.3% sensitivity, 96.9% specificity (differences between carcinomas/pheochromocytomas and adenomas/metastases); Lac/Cr ≤ -7.449, 90.9% sensitivity and 77.8% specificity (differences between pheochromocytomas and carcinomas/adenomas). Information provided by 2D-1H-MRS were effective and allowed for the differentiation between adrenal masses and nodules in most cases of lesions with > 1.0 cm in diameter.

The effects of convergence ratio on the implosion behavior of DT layered inertial confinement fusion capsules

DOE PAGES

Haines, Brian M.; Yi, S. A.; Olson, R. E.; ...

2017-07-10

The wetted foam capsule design for inertial confinement fusion capsules, which includes a foam layer wetted with deuterium-tritium liquid, enables layered capsule implosions with a wide range of hot-spot convergence ratios (CR) on the National Ignition Facility. In this paper, we present a full-scale wetted foam capsule design that demonstrates high gain in one-dimensional simulations. In these simulations, increasing the convergence ratio leads to an improved capsule yield due to higher hot-spot temperatures and increased fuel areal density. High-resolution two-dimensional simulations of this design are presented with detailed and well resolved models for the capsule fill tube, support tent, surfacemore » roughness, and predicted asymmetries in the x-ray drive. Our modeling of these asymmetries is validated by comparisons with available experimental data. In 2D simulations of the full-scale wetted foam capsule design, jetting caused by the fill tube is prevented by the expansion of the tungsten-doped shell layer due to preheat. While the impacts of surface roughness and predicted asymmetries in the x-ray drive are enhanced by convergence effects, likely underpredicted in 2D at high CR, simulations predict that the capsule is robust to these features. Nevertheless, the design is highly susceptible to the effects of the capsule support tent, which negates all of the one-dimensional benefits of increasing the convergence ratio. Indeed, when the support tent is included in simulations, the yield decreases as the convergence ratio is increased for CR > 20. Finally and nevertheless, the results suggest that the full-scale wetted foam design has the potential to outperform ice layer capsules given currently achievable levels of asymmetries when fielded at low convergence ratios (CR < 20).« less

The Urinary Uric Acid/Creatinine Ratio is An Adjuvant Marker for Perinatal Asphyxia

PubMed Central

Bhongir, Aparna Varma; Yakama, Akhil Varma Venkata; Saha, Subhajit; Radia, Sejal B.; Pabbati, Jayalakshmi

2015-01-01

Objective To assess the urinary uric acid/creatinine ratio (UA/Cr) in relation to Apgar score and cord blood gas analysis in identification of perinatal asphyxia and to define the cutoff values. Design case control study. Setting The newborns admitted in the department of pediatrics and NICU of Mediciti Institute of Medical Science, Ghanpur, Medchal mandal, Telangana from May-July 2011 were enrolled. Participants/patients The study was conducted on 31 (18 males, 13 females) controls and 18 (12males, 6 females) asphyxiated neonates. Outcome Measure(s) 5ml of arterial cord blood of newborn collected at the time of birth and spot urine samples were collected within 24-72 hours of life. Cord blood gas analysis were done immediately and Urinary uric acid was measured by modified Uricase method, urinary creatinine by modified kinetic Jaffe's reaction. Results The mean urinary uric acid and creatinine ratio (2.58± 0.48 vs 1.89 ± 0.59) is significantly higher in Asphyxiated group than in the control group. The umbilical cord blood pH had significant positive correlation with 1st minute Apgar score (r= 0.41, p=0.003), 5th minute Apgar (r= 0.44, p=0.002), while urinary UA/Cr ratio had significant negative correlation with cord blood pH (r= -0.63, p=0.002). Urinary UA/Cr ratio with criterion of >2.43 had 80% sensitivity, 87.5% specificity with AUC of 0.84 (p=0.003) had a better predictive value. Conclusions Urinary UA/Cr ratio is easy, non-invasive, painless and economical adjuvant parameter with better predictive value for diagnosing perinatal asphyxia with simple diagnostic equipment. PMID:26998526

The effects of convergence ratio on the implosion behavior of DT layered inertial confinement fusion capsules

NASA Astrophysics Data System (ADS)

Haines, Brian M.; Yi, S. A.; Olson, R. E.; Khan, S. F.; Kyrala, G. A.; Zylstra, A. B.; Bradley, P. A.; Peterson, R. R.; Kline, J. L.; Leeper, R. J.; Shah, R. C.

2017-07-01

The wetted foam capsule design for inertial confinement fusion capsules, which includes a foam layer wetted with deuterium-tritium liquid, enables layered capsule implosions with a wide range of hot-spot convergence ratios (CR) on the National Ignition Facility. We present a full-scale wetted foam capsule design that demonstrates high gain in one-dimensional simulations. In these simulations, increasing the convergence ratio leads to an improved capsule yield due to higher hot-spot temperatures and increased fuel areal density. High-resolution two-dimensional simulations of this design are presented with detailed and well resolved models for the capsule fill tube, support tent, surface roughness, and predicted asymmetries in the x-ray drive. Our modeling of these asymmetries is validated by comparisons with available experimental data. In 2D simulations of the full-scale wetted foam capsule design, jetting caused by the fill tube is prevented by the expansion of the tungsten-doped shell layer due to preheat. While the impacts of surface roughness and predicted asymmetries in the x-ray drive are enhanced by convergence effects, likely underpredicted in 2D at high CR, simulations predict that the capsule is robust to these features. Nevertheless, the design is highly susceptible to the effects of the capsule support tent, which negates all of the one-dimensional benefits of increasing the convergence ratio. Indeed, when the support tent is included in simulations, the yield decreases as the convergence ratio is increased for CR > 20. Nevertheless, the results suggest that the full-scale wetted foam design has the potential to outperform ice layer capsules given currently achievable levels of asymmetries when fielded at low convergence ratios (CR < 20).

Selective hierarchical patterning of silicon nanostructures via soft nanostencil lithography

NASA Astrophysics Data System (ADS)

Du, Ke; Ding, Junjun; Wathuthanthri, Ishan; Choi, Chang-Hwan

2017-11-01

It is challenging to hierarchically pattern high-aspect-ratio nanostructures on microstructures using conventional lithographic techniques, where photoresist (PR) film is not able to uniformly cover on the microstructures as the aspect ratio increases. Such non-uniformity causes poor definition of nanopatterns over the microstructures. Nanostencil lithography can provide an alternative means to hierarchically construct nanostructures on microstructures via direct deposition or plasma etching through a free-standing nanoporous membrane. In this work, we demonstrate the multiscale hierarchical fabrication of high-aspect-ratio nanostructures on microstructures of silicon using a free-standing nanostencil, which is a nanoporous membrane consisting of metal (Cr), PR, and anti-reflective coating. The nanostencil membrane is used as a deposition mask to define Cr nanodot patterns on the predefined silicon microstructures. Then, deep reactive ion etching is used to hierarchically create nanostructures on the microstructures using the Cr nanodots as an etch mask. With simple modification of the main fabrication processes, high-aspect-ratio nanopillars are selectively defined only on top of the microstructures, on bottom, or on both top and bottom.

Electron-capture Isotopes Could Constrain Cosmic-Ray Propagation Models

NASA Astrophysics Data System (ADS)

Benyamin, David; Shaviv, Nir J.; Piran, Tsvi

2017-12-01

Electron capture (EC) isotopes are known to provide constraints on the low-energy behavior of cosmic rays (CRs), such as reacceleration. Here, we study the EC isotopes within the framework of the dynamic spiral-arms CR propagation model in which most of the CR sources reside in the galactic spiral arms. The model was previously used to explain the B/C and sub-Fe/Fe ratios. We show that the known inconsistency between the 49Ti/49V and 51V/51Cr ratios remains also in the spiral-arms model. On the other hand, unlike the general wisdom that says the isotope ratios depend primarily on reacceleration, we find here that the ratio also depends on the halo size (Z h) and, in spiral-arms models, also on the time since the last spiral-arm passage ({τ }{arm}). Namely, EC isotopes can, in principle, provide interesting constraints on the diffusion geometry. However, with the present uncertainties in the lab measurements of both the electron attachment rate and the fragmentation cross sections, no meaningful constraint can be placed.

Selective hierarchical patterning of silicon nanostructures via soft nanostencil lithography.

PubMed

Du, Ke; Ding, Junjun; Wathuthanthri, Ishan; Choi, Chang-Hwan

2017-11-17

It is challenging to hierarchically pattern high-aspect-ratio nanostructures on microstructures using conventional lithographic techniques, where photoresist (PR) film is not able to uniformly cover on the microstructures as the aspect ratio increases. Such non-uniformity causes poor definition of nanopatterns over the microstructures. Nanostencil lithography can provide an alternative means to hierarchically construct nanostructures on microstructures via direct deposition or plasma etching through a free-standing nanoporous membrane. In this work, we demonstrate the multiscale hierarchical fabrication of high-aspect-ratio nanostructures on microstructures of silicon using a free-standing nanostencil, which is a nanoporous membrane consisting of metal (Cr), PR, and anti-reflective coating. The nanostencil membrane is used as a deposition mask to define Cr nanodot patterns on the predefined silicon microstructures. Then, deep reactive ion etching is used to hierarchically create nanostructures on the microstructures using the Cr nanodots as an etch mask. With simple modification of the main fabrication processes, high-aspect-ratio nanopillars are selectively defined only on top of the microstructures, on bottom, or on both top and bottom.

The use of ZFP lossy floating point data compression in tornado-resolving thunderstorm simulations

NASA Astrophysics Data System (ADS)

Orf, L.

2017-12-01

In the field of atmospheric science, numerical models are used to produce forecasts of weather and climate and serve as virtual laboratories for scientists studying atmospheric phenomena. In both operational and research arenas, atmospheric simulations exploiting modern supercomputing hardware can produce a tremendous amount of data. During model execution, the transfer of floating point data from memory to the file system is often a significant bottleneck where I/O can dominate wallclock time. One way to reduce the I/O footprint is to compress the floating point data, which reduces amount of data saved to the file system. In this presentation we introduce LOFS, a file system developed specifically for use in three-dimensional numerical weather models that are run on massively parallel supercomputers. LOFS utilizes the core (in-memory buffered) HDF5 driver and includes compression options including ZFP, a lossy floating point data compression algorithm. ZFP offers several mechanisms for specifying the amount of lossy compression to be applied to floating point data, including the ability to specify the maximum absolute error allowed in each compressed 3D array. We explore different maximum error tolerances in a tornado-resolving supercell thunderstorm simulation for model variables including cloud and precipitation, temperature, wind velocity and vorticity magnitude. We find that average compression ratios exceeding 20:1 in scientifically interesting regions of the simulation domain produce visually identical results to uncompressed data in visualizations and plots. Since LOFS splits the model domain across many files, compression ratios for a given error tolerance can be compared across different locations within the model domain. We find that regions of high spatial variability (which tend to be where scientifically interesting things are occurring) show the lowest compression ratios, whereas regions of the domain with little spatial variability compress extremely well. We observe that the overhead for compressing data with ZFP is low, and that compressing data in memory reduces the amount of memory overhead needed to store the virtual files before they are flushed to disk.

Optimum mix for fly ash geopolymer binder based on workability and compressive strength

NASA Astrophysics Data System (ADS)

Arafa, S. A.; Ali, A. Z. M.; Awal, A. S. M. A.; Loon, L. Y.

2018-04-01

The request of concrete is increasing every day for sustaining the necessity of development of structure. The production of OPC not only consumes big amount of natural resources and energy, but also emit significant quantity of CO2 to the atmosphere. Therefore, it is necessary to find alternatives like Geopolymer to make the concrete environment friendly. Geopolymer is an inorganic alumino-silicate compound, produced from fly ash. This paper describes the experimental work conducted by casting 40 geopolymer paste mixes, and was cured at 80°C for 24 h to evaluate the effect of various parameters affecting the workability and compressive strength. Alkaline solution to fly ash ratio and sodium hydroxide (NaOH) concentration were chosen as the key parameters of strength and workability. Laboratory investigation with different percentage of sodium hydroxide concentration and different alkaline liquid to fly ash ratio reveals that the optimum ratios are 10 M, AL/FA=0.5. It has generally been found that the workability decreased and the compressive strength increased with an increase in the concentration of sodium hydroxide solution. However, workability was increased and the compressive strength was decreased with the increase in the ratio of fly ash to alkaline solution.

Effect of small addition of Cr on stability of retained austenite in high carbon steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hossain, Rumana; Pahlevani, Farshid, E-mail: f.pah

High carbon steels with dual phase structures of martensite and austenite have considerable potential for industrial application in high abrasion environments due to their hardness, strength and relatively low cost. To design cost effective high carbon steels with superior properties, it is crucial to identify the effect of Chromium (Cr) on the stability of retained austenite (RA) and to fully understand its effect on solid-state phase transition. This study addresses this important knowledge gap. Using standard compression tests on bulk material, quantitative X-ray diffraction analysis, nano-indentation on individual austenitic grains, transmission electron microscopy and electron backscatter diffraction–based orientation microscopy techniques,more » the authors investigated the effect of Cr on the microstructure, transformation behaviour and mechanical stability of retained austenite in high carbon steel, with varying Cr contents. The results revealed that increasing the Cr %, altered the morphology of the RA and increased its stability, consequently, increasing the critical pressure for martensitic transformation. This study has critically addressed the elastoplastic behaviour of retained austenite – and provides a deep understanding of the effect of small additions of Cr on the metastable austenite of high carbon steel from the macro- to nano-level. Consequently, it paves the way for new applications for high carbon low alloy steels. - Highlights: • Effect of small addition of Cr on metastable austenite of high carbon steel from the macro- to nano-level • A multi-scale study of elastoplastic behaviour of retained austenite in high carbon steel • The mechanical stability of retained austenite during plastic deformation increased with increasing Cr content • Effect of grain boundary misorientation angle on hardness of individual retained austenite grains in high carbon steel.« less

Light-weight reference-based compression of FASTQ data.

PubMed

Zhang, Yongpeng; Li, Linsen; Yang, Yanli; Yang, Xiao; He, Shan; Zhu, Zexuan

2015-06-09

The exponential growth of next generation sequencing (NGS) data has posed big challenges to data storage, management and archive. Data compression is one of the effective solutions, where reference-based compression strategies can typically achieve superior compression ratios compared to the ones not relying on any reference. This paper presents a lossless light-weight reference-based compression algorithm namely LW-FQZip to compress FASTQ data. The three components of any given input, i.e., metadata, short reads and quality score strings, are first parsed into three data streams in which the redundancy information are identified and eliminated independently. Particularly, well-designed incremental and run-length-limited encoding schemes are utilized to compress the metadata and quality score streams, respectively. To handle the short reads, LW-FQZip uses a novel light-weight mapping model to fast map them against external reference sequence(s) and produce concise alignment results for storage. The three processed data streams are then packed together with some general purpose compression algorithms like LZMA. LW-FQZip was evaluated on eight real-world NGS data sets and achieved compression ratios in the range of 0.111-0.201. This is comparable or superior to other state-of-the-art lossless NGS data compression algorithms. LW-FQZip is a program that enables efficient lossless FASTQ data compression. It contributes to the state of art applications for NGS data storage and transmission. LW-FQZip is freely available online at: http://csse.szu.edu.cn/staff/zhuzx/LWFQZip.

Relationship between weight of rescuer and quality of chest compression during cardiopulmonary resuscitation

PubMed Central

2014-01-01

Background According to the guidelines for cardiopulmonary resuscitation (CPR), the rotation time for chest compression should be about 2 min. The quality of chest compressions is related to the physical fitness of the rescuer, but this was not considered when determining rotation time. The present study aimed to clarify associations between body weight and the quality of chest compression and physical fatigue during CPR performed by 18 registered nurses (10 male and 8 female) assigned to light and heavy groups according to the average weight for each sex in Japan. Methods Five-minute chest compressions were then performed on a manikin that was placed on the floor. Measurement parameters were compression depth, heart rate, oxygen uptake, integrated electromyography signals, and rating of perceived exertion. Compression depth was evaluated according to the ratio (%) of adequate compressions (at least 5 cm deep). Results The ratio of adequate compressions decreased significantly over time in the light group. Values for heart rate, oxygen uptake, muscle activity defined as integrated electromyography signals, and rating of perceived exertion were significantly higher for the light group than for the heavy group. Conclusion Chest compression caused increased fatigue among the light group, which consequently resulted in a gradual fall in the quality of chest compression. These results suggested that individuals with a lower body weight should rotate at 1-min intervals to maintain high quality CPR and thus improve the survival rates and neurological outcomes of victims of cardiac arrest. PMID:24957919

Contributors to chromium isotope variation of meteorites

NASA Astrophysics Data System (ADS)

Qin, Liping; Alexander, Conel M. O.'D.; Carlson, Richard W.; Horan, Mary F.; Yokoyama, Tetsuya

2010-02-01

We report the results of a comprehensive, high precision survey of the Cr isotopic compositions of primitive chondrites, along with some differentiated meteorites. To ensure complete dissolution of our samples, they were first fused with lithium borate-tetraborate at 1050-1000 °C. Relative to the NIST Cr standard SRM 3112a, carbonaceous chondrites exhibit excesses in 54Cr/ 52Cr from 0.4 to 1.6 ɛ (1 ɛ = 1 part in 10,000), and ordinary chondrites display a common 54Cr/ 52Cr deficit of ˜0.4 ɛ. Analyses of acid-digestion residues of chondrites show that carbonaceous and ordinary chondrites share a common 54Cr-enriched carrier, which is characterized by a large excess in 54Cr/ 52Cr (up to 200 ɛ) associated with a very small deficit in 53Cr/ 52Cr (<2 ɛ). We did not find 54Cr anomalies in either bulk enstatite chondrites or in leachates of their acid-digestion residues. This either requires that the enstatite chondrite parent bodies did not incorporate the 54Cr anomaly carrier phase during their accretion, or the phase was destroyed by parent body metamorphism. Chromium in the terrestrial rocks and lunar samples analyzed here show no deviation from the NIST SRM 3112a Cr standard. The eucrite and Martian meteorites studied exhibit small deficits in 54Cr/ 52Cr. The 54Cr/ 52Cr variations among different meteorite classes suggest that there was a spatial and/or temporal heterogeneity in the distribution of a 54Cr-rich component in the inner Solar System. We confirm the correlated excesses in 54Cr/ 52Cr and 53Cr/ 52Cr for bulk carbonaceous chondrites, but the new data yield a steeper slope (˜6.6) than that reported in Shukolyukov and Lugmair (2006). The correlated excesses may affect the use of the Mn-Cr chronometer in carbonaceous chondrites. We could not confirm the bulk carbonaceous chondrite Mn-Cr isochron reported by Shukolyukov and Lugmair (2006) and Moynier et al. (2007), mostly because we find much smaller total variations in ɛ53Cr (˜0.2). All bulk chondrites have small ɛ53Cr excesses (up to 0.3) relative to the Earth, most likely reflecting the sub-chondritic Mn/Cr ratio of the Earth. The ɛ53Cr variations in chondrites do seem to grossly correlate with Mn/Cr and yield an initial Solar System 53Mn/ 55Mn value of 5.4(±2.4) × 10 -6, corresponding to an absolute age of 4566.4 (±2.2) Ma. Nuclear interactions with cosmic rays result in coupled excesses in ɛ54Cr and ɛ53Cr with a ˜4:1 ratio in phases with high Fe/Cr. These are most dramatically demonstrated in the iron meteorite Carbo, showing excesses in ɛ54Cr of up to 140 ɛ. These new results show that the Mn-Cr chronometer should be used with caution in samples/minerals with high Fe/Cr and long cosmic ray exposure ages.

Effects of external magnetic field and out-of-plane strain on magneto-optical Kerr spectra in CrI3 monolayer.

PubMed

Guo, Guanxing; Bi, Gang; Cai, Chunfeng; Wu, Huizhen

2018-07-18

Magnetic semiconductors based on two-dimensional (2D) crystals have attracted attention owing to their intrinsic ferromagnetism and have potential for spintronic devices. Here, full-potential linearized augmented plane wave plus local orbitals method is used to explore the structural, electronic, magnetic, and magneto-optical properties of CrI 3 monolayer. Our first-principles calculations show that CrI 3 monolayer is a ferromagnetic indirect semiconductor with spin-up and spin-down band gaps of 1.23 and 1.90 eV, respectively, and a magnetic moment of 2.93 [Formula: see text] per Cr atom. Based on the macroscopic linear response theory, we systematically study the influences of external magnetic field and out-of-plane strain on the magneto-optical Kerr effect spectra in CrI 3 monolayer. The Kerr rotation of CrI 3 monolayer at 1.96 eV photon energy is [Formula: see text], which is consistent with the recent experiments. We find that the Kerr rotation reaches its maximum when the external magnetic field is perpendicular to CrI 3 plane, while it is almost zero on turning the magnetic field in the plane. This result as well as the sizable magnetocrystalline anisotropy energy (MAE) of 0.79 meV verifies that CrI 3 monolayer has a strong magnetic anisotropy with an out-of-plane easy axis. Further, applying out-of-plane compressive and tensile strain upon CrI 3 monolayer, we observe a redshift of the Kerr rotation spectra with the increase of the strain and the peak values of the Kerr rotation increase correspondingly. The rich electronic and magnetic properties, especially the magneto-optical spectra, render CrI 3 monolayer a promising 2D magnetic material for applications from sensing to data storage.

Longitudinal changes in corneal curvature and its relationship to axial length in the Correction of Myopia Evaluation Trial (COMET) cohort.

PubMed

Scheiman, Mitchell; Gwiazda, Jane; Zhang, Qinghua; Deng, Li; Fern, Karen; Manny, Ruth E; Weissberg, Erik; Hyman, Leslie

2016-01-01

To describe longitudinal changes in corneal curvature (CC) and axial length (AL) over 14 years, and to explore the relationship between AL and CC, and the axial length/corneal radius (AL/CR) ratio. In total 469, 6 to <12-year-old, children were enrolled in COMET. Measurements of refractive error, CC (D), CR (mm), and ocular component dimensions including AL were gathered annually. Linear mixed models were used to evaluate longitudinal changes adjusting for covariates (gender, ethnicity, lens type, baseline age and baseline refraction). The Pearson correlation coefficient between AL and CC was computed at each visit. There was a slight but significant (p<0.0001) flattening in CC over 14 years. At all visits females had significantly steeper CC than males (overall difference=0.53 D, p<0.0001). Caucasians had the steepest CC, and Hispanics the flattest (p=0.001). The correlation between AL and CC was -0.70 (p<0.0001) at baseline (mean age=9.3 years) and decreased to -0.53 (p<0.0001) at the 14-year visit (mean age=24.1 years). The average AL/CR ratio was 3.15 at baseline and increased to 3.31 at the 14-year visit. The correlation between the magnitude of myopia and AL/CR ratio was significantly higher (p<0.0001) at each visit than the correlation between myopia and AL alone. Differences in average corneal curvature by age, gender, and ethnicity observed in early childhood remain consistent as myopia progresses and stabilizes. This study also demonstrates increases in the AL/CR ratio as myopia progresses and then stabilizes, supporting observations from previous cross-sectional data. Copyright © 2015 Spanish General Council of Optometry. Published by Elsevier Espana. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salloum, Maher; Fabian, Nathan D.; Hensinger, David M.

Exascale computing promises quantities of data too large to efficiently store and transfer across networks in order to be able to analyze and visualize the results. We investigate compressed sensing (CS) as an in situ method to reduce the size of the data as it is being generated during a large-scale simulation. CS works by sampling the data on the computational cluster within an alternative function space such as wavelet bases and then reconstructing back to the original space on visualization platforms. While much work has gone into exploring CS on structured datasets, such as image data, we investigate itsmore » usefulness for point clouds such as unstructured mesh datasets often found in finite element simulations. We sample using a technique that exhibits low coherence with tree wavelets found to be suitable for point clouds. We reconstruct using the stagewise orthogonal matching pursuit algorithm that we improved to facilitate automated use in batch jobs. We analyze the achievable compression ratios and the quality and accuracy of reconstructed results at each compression ratio. In the considered case studies, we are able to achieve compression ratios up to two orders of magnitude with reasonable reconstruction accuracy and minimal visual deterioration in the data. Finally, our results suggest that, compared to other compression techniques, CS is attractive in cases where the compression overhead has to be minimized and where the reconstruction cost is not a significant concern.« less

Morphology and stability in a half-metallic ferromagnetic CrO 2 compound of nanoparticles synthesized via a polymer precursor

NASA Astrophysics Data System (ADS)

Biswas, S.; Ram, S.

2004-11-01

Nanoparticles of stable CrO2 of a half-metallic ferromagnet are synthesized with a novel chemical method involving a Cr4+-polymer composite precursor. A single phase CrO2 of D4h 14 : P42 / mnm tetragonal crystal structure (lattice parameters a = 0.4250 and c = 0.3190 nm) lies after firing the precursor at 350 °C for 1 h in air. Microstructure reveals single domain CrO2 particles of thin platelets (aspect ratio ∼1) of average 50 nm diameter and 35 nm thickness. In air, unless heating at temperatures above 500 °C, no due CrO2 → Cr2O3 phase transformation encounters. The results are presented in terms of X-ray diffraction and thermal or thermogravimetric analysis of precursor and derived CrO2 powder.

Mid-IR soliton compression in silicon optical fibers and fiber tapers.

PubMed

Peacock, Anna C

2012-03-01

Numerical simulations are used to investigate soliton compression in silicon core optical fibers at 2.3 μm in the mid-infrared waveguide regime. Compression in both standard silicon fibers and fiber tapers is compared to establish the relative compression ratios for a range of input pulse conditions. The results show that tapered fibers can be used to obtain higher levels of compression for moderate soliton orders and thus lower input powers. © 2012 Optical Society of America

Sequential neural text compression.

PubMed

Schmidhuber, J; Heil, S

1996-01-01

The purpose of this paper is to show that neural networks may be promising tools for data compression without loss of information. We combine predictive neural nets and statistical coding techniques to compress text files. We apply our methods to certain short newspaper articles and obtain compression ratios exceeding those of the widely used Lempel-Ziv algorithms (which build the basis of the UNIX functions "compress" and "gzip"). The main disadvantage of our methods is that they are about three orders of magnitude slower than standard methods.

The effect of lossy image compression on image classification

NASA Technical Reports Server (NTRS)

Paola, Justin D.; Schowengerdt, Robert A.

1995-01-01

We have classified four different images, under various levels of JPEG compression, using the following classification algorithms: minimum-distance, maximum-likelihood, and neural network. The training site accuracy and percent difference from the original classification were tabulated for each image compression level, with maximum-likelihood showing the poorest results. In general, as compression ratio increased, the classification retained its overall appearance, but much of the pixel-to-pixel detail was eliminated. We also examined the effect of compression on spatial pattern detection using a neural network.

Robust QRS detection for HRV estimation from compressively sensed ECG measurements for remote health-monitoring systems.

PubMed

Pant, Jeevan K; Krishnan, Sridhar

2018-03-15

To present a new compressive sensing (CS)-based method for the acquisition of ECG signals and for robust estimation of heart-rate variability (HRV) parameters from compressively sensed measurements with high compression ratio. CS is used in the biosensor to compress the ECG signal. Estimation of the locations of QRS segments is carried out by applying two algorithms on the compressed measurements. The first algorithm reconstructs the ECG signal by enforcing a block-sparse structure on the first-order difference of the signal, so the transient QRS segments are significantly emphasized on the first-order difference of the signal. Multiple block-divisions of the signals are carried out with various block lengths, and multiple reconstructed signals are combined to enhance the robustness of the localization of the QRS segments. The second algorithm removes errors in the locations of QRS segments by applying low-pass filtering and morphological operations. The proposed CS-based method is found to be effective for the reconstruction of ECG signals by enforcing transient QRS structures on the first-order difference of the signal. It is demonstrated to be robust not only to high compression ratio but also to various artefacts present in ECG signals acquired by using on-body wireless sensors. HRV parameters computed by using the QRS locations estimated from the signals reconstructed with a compression ratio as high as 90% are comparable with that computed by using QRS locations estimated by using the Pan-Tompkins algorithm. The proposed method is useful for the realization of long-term HRV monitoring systems by using CS-based low-power wireless on-body biosensors.

Fast and accurate face recognition based on image compression

NASA Astrophysics Data System (ADS)

Zheng, Yufeng; Blasch, Erik

2017-05-01

Image compression is desired for many image-related applications especially for network-based applications with bandwidth and storage constraints. The face recognition community typical reports concentrate on the maximal compression rate that would not decrease the recognition accuracy. In general, the wavelet-based face recognition methods such as EBGM (elastic bunch graph matching) and FPB (face pattern byte) are of high performance but run slowly due to their high computation demands. The PCA (Principal Component Analysis) and LDA (Linear Discriminant Analysis) algorithms run fast but perform poorly in face recognition. In this paper, we propose a novel face recognition method based on standard image compression algorithm, which is termed as compression-based (CPB) face recognition. First, all gallery images are compressed by the selected compression algorithm. Second, a mixed image is formed with the probe and gallery images and then compressed. Third, a composite compression ratio (CCR) is computed with three compression ratios calculated from: probe, gallery and mixed images. Finally, the CCR values are compared and the largest CCR corresponds to the matched face. The time cost of each face matching is about the time of compressing the mixed face image. We tested the proposed CPB method on the "ASUMSS face database" (visible and thermal images) from 105 subjects. The face recognition accuracy with visible images is 94.76% when using JPEG compression. On the same face dataset, the accuracy of FPB algorithm was reported as 91.43%. The JPEG-compressionbased (JPEG-CPB) face recognition is standard and fast, which may be integrated into a real-time imaging device.

Microstructures, mechanical properties, and degradation behaviors of heat-treated Mg-Sr alloys as potential biodegradable implant materials.

PubMed

Wang, Yuxiang; Tie, Di; Guan, Renguo; Wang, Ning; Shang, Yingqiu; Cui, Tong; Li, Junqiao

2018-01-01

In previous studies, Mg-Sr alloys exhibited great biocompatibility with regard to test animals, and enhanced peri-implant bone formation. The objective of the present study was to investigate the effects of heat treatments on the mechanical and corrosion properties of Mg-Sr alloys. Various heat-treated Mg-xSr (x = 0.5, 1, and 2wt%, nominal composition) alloys were prepared using homogenization and aging treatments. Mechanical tests were performed at room temperature on the as-cast, homogenized, and peak-aged alloys. As the Sr content increased, the volume fraction of Mg 17 Sr 2 phases within the as-cast alloys increased; in addition, the mechanical strength of the alloys initially increased and subsequently decreased, while the ductility decreased. Following the homogenization treatment, the mechanical strength of the alloys decreased, and the ductility increased. Nano-sized Mg 17 Sr 2 phases were re-precipitated during the aging treatment. The age-hardening response at 160°C was enhanced as the Sr content increased. Following the aging treatment, there was an increase in the mechanical strength of the alloys; however, there was a slight reduction in the ductility. Immersion tests were conducted at 37°C for 360h, using Hank's buffered salt solution (HBSS), to study the degradation behavior of the alloys. As the Sr content of the Mg-Sr alloys increased, the corrosion rate (CR) increased owing to the galvanic effect. The homogenization treatment consequently reduced the CR dramatically, and the aging treatment had a slight effect on the CR. The peak-aged Mg-1Sr (wt%) alloy exhibited the best combination of properties. The tensile yield strength (TYS), ultimate tensile strength (UTS), elongation, compressive yield strength (CYS), ultimate compressive strength (UCS), compressibility, and CR of the as-cast Mg-1Sr (wt%) alloy were 56.0MPa, 92.67MPa, 1.27%, 171.4MPa, 243.6MPa, 22.3%, and 1.76mm/year, respectively. The respective results obtained for the peak-aged Mg-1Sr (wt%) alloys were 69.7MPa, 135.6MPa, 3.22%, 183.1MPa, 273.6MPa, 27.6%, and 1.33mm/year. Following immersion in HBSS, the primary corrosion products of the peak-aged Mg-1Sr (wt%) alloy were Mg(OH) 2 , MgO, MgCO 3 , Mg 3 (PO 4 ) 2 , MgHPO 4 , and Mg(H 2 PO 4 ) 2 , which enhanced the corrosion resistance by forming a composite corrosion film. Copyright © 2017 Elsevier Ltd. All rights reserved.

Longitudinal cerebral metabolic changes in pig-tailed macaques infected with the neurovirulent virus SIVsmmFGb

PubMed Central

Li, Chun-Xia; Zhang, Xiaodong; Komery, Amelia; Li, Yingxia; Mao, Hui; Herndon, James G; Novembre, Francis J

2014-01-01

Longitudinal cerebral metabolite changes in pig-tailed macaques inoculated with the simian immunodeficiency virus SIVsmmFGb were evaluated with in vivo proton MRS at 3T. Blood sample collection, and MRS were carried out before and 2, 4, 8, 12, 16, 20 and 24 weeks after SIV inoculation. Significant reduction of N-acetylaspartate (NAA)/creatine (Cr) and Choline (Cho)/Cr ratios in prefrontal grey matter (PGM) and glutamate/glutamine (Glx)/Cr ratios in striatum, and increase of myo-inositol (mI)/Cr in striatum were observed during acute SIV infection. The metabolite alterations during the SIVsmmFGb infection are largely in agreement with previous findings in other non-human primate models and HIV patients. Also, NAA/Cr in PGM and striatum and Glx/Cr in striatum are negatively correlated with the percentage of CD8+ T cells after the SIV infection, suggesting the interaction between brain metabolite and immune dysfunction. The present study complements previous studies by describing the time course of alterations of brain metabolites during SIVsmmFGb infection. The findings further demonstrate the efficacy of the SIVsmmFGb-infected macaque as a model to characterize central nervous system infection using novel neuroimaging approaches and also as a tool for exploration of novel and advanced neuroimaging techniques in HIV/AIDS studies. PMID:25377443

Dramatic Improvement on Catalyst Loadings and Molar Ratios of Coupling Partners for Ni/Cr-Mediated Coupling Reactions: Heterobimetallic Catalysts

PubMed Central

Liu, Xiang; Henderson, James A.; Sasaki, Takeo; Kishi, Yoshito

2009-01-01

Two new ligands 1a,b have been reported. Upon treatment with one equivalent of NiCl2·(MeOCH2)2, 1a,b give the corresponding Ni-complexes. X-ray analysis of 1a·NiCl2 has established that the NiCl2 is selectively coordinated to the phenanthroline nitrogens. Ni/Cr-heterobimetallic catalysts 1a,b·CrCl2/NiCl2, prepared from 1a,b·NiCl2, have been shown to behave exceptionally well for the catalytic asymmetric Ni/Cr-mediated couplings, with the highlights including: (1) 1~2 mol % catalysts are sufficient to complete the coupling, (2) only a negligible amount of the dimers, by-products formed through the alkenyl Ni-species, is observed, (3) the coupling completes even with a 1:1 molar ratio of the coupling partners, and (4) the asymmetric induction is practically identical with that obtained in the coupling with the Cr-catalyst prepared from (S)-sulfonamide 2a,b. Using 4 additional aldehydes, a scope of the new Ni/Cr-heterobimetallic catalysts is briefly studied. Applicability of new catalysts to polyfunctional substrates has been demonstrated, with use of two C-C bond-formations chosen from the halichondrin/E7389 synthesis as examples. PMID:19874019

Longitudinal cerebral metabolic changes in pig-tailed macaques infected with the neurovirulent virus SIVsmmFGb.

PubMed

Li, Chun-Xia; Zhang, Xiaodong; Komery, Amelia; Li, Yingxia; Mao, Hui; Herndon, James G; Novembre, Francis J

2014-12-01

Longitudinal cerebral metabolite changes in pig-tailed macaques inoculated with the simian immunodeficiency virus SIVsmmFGb were evaluated with in vivo proton MRS at 3 T. Blood sample collection, and MRS were carried out before and 2, 4, 8, 12, 16, 20, and 24 weeks after SIV inoculation. Significant reduction of N-acetylaspartate (NAA)/creatine (Cr) and choline (Cho)/Cr ratios in prefrontal gray matter (PGM) and glutamate/glutamine(Glx)/Cr ratio in striatum, and increase of myo-inositol (mI)/Cr in striatum were observed during acute SIV infection. The metabolite alterations during the SIVsmmFGb infection are largely in agreement with previous findings in other non-human primate models and HIV patients. Also, NAA/Cr in PGM and striatum and Glx/Cr in striatum are negatively correlated with the percentage of CD8+ T cells after the SIV infection, suggesting the interaction between brain metabolite and immune dysfunction. The present study complements previous studies by describing the time course of alterations of brain metabolites during SIVsmmFGb infection. The findings further demonstrate the efficacy of the SIVsmmFGb-infected macaque as a model to characterize central nervous system infection using novel neuroimaging approaches and also as a tool for exploration of novel and advanced neuroimaging techniques in HIV/AIDS studies.

Isotopic, Chemical and Mineralogical Investigation's of Extraterrestrial Materials

NASA Technical Reports Server (NTRS)

Lugmair, G. W.

2003-01-01

During the grant period we have concentrated on the following main topics: 1. Enstatite meteorites and original heterogeneity of Mn-53 distribution in the solar nebula. We have completed our studies of the enstatite chondrites. 2. Processes of planetary differentiation. We have completed our study of silicate clasts from the mesosiderite Vaca Muerta and found that the global Mn/Cr fractionation event that established mantle source reservoirs on the parent body of the Vaca Muerta silicate clasts occurred approx. 2 Ma after a similar event on the howardite-eucrite-diogenite (HED) parent body. 3. Carbonaceous chondrites. Much effort has been devoted during the last three years to the investigation of this important class of meteorites. 4. Early solar system timescales. Based on the studies of the Mn-53 - Cr-53 isotope system in various meteorites and using results obtained with other isotope chronometers we constructed an absolute time-scale for events in the early solar system. 5.Unusual meteorites. We have studied the anomalous pallasite Eagle Station. 6. The chromium isotopic composition as a tracer for extraterrestrial material on Earth. Based on the observed difference in the Cr-53/Cr-52 ratios between Earth and the other solar system objects we developed a method for detecting cosmic materials on Earth using the Cr-53/Cr-52 ratio as a tracer.

Evaluation of the microstructure, secondary dendrite arm spacing, and mechanical properties of Al-Si alloy castings made in sand and Fe-Cr slag molds

NASA Astrophysics Data System (ADS)

Narasimha Murthy, I.; Babu Rao, J.

2017-07-01

The microstructure and mechanical properties of as-cast A356 (Al-Si) alloy castings were investigated. A356 alloy was cast into three different molds composed of sand, ferrochrome (Fe-Cr) slag, and a mixture of sand and Fe-Cr. A sodium silicate-CO2 process was used to make the necessary molds. Cylindrical-shaped castings were prepared. Cast products with no porosity and a good surface finish were achieved in all of the molds. These castings were evaluated for their metallography, secondary dendrite arm spacing (SDAS), and mechanical properties, including hardness, compression, tensile, and impact properties. Furthermore, the tensile and impact samples were analyzed by fractography. The results show that faster heat transfer in the Fe-Cr slag molds than in either the silica sand or mixed molds led to lower SDAS values with a refined microstructure in the products cast in Fe-Cr slag molds. Consistent and enhanced mechanical properties were observed in the slag mold products than in the castings obtained from either sand or mixed molds. The fracture surface of the slag mold castings shows a dimple fracture morphology with a transgranular fracture nature. However, the fracture surfaces of the sand mold castings display brittle fracture. In conclusion, products cast in Fe-Cr slag molds exhibit an improved surface finish and enhanced mechanical properties compared to those of products cast in sand and mixed molds.

Variable convergence liquid layer implosions on the National Ignition Facility

NASA Astrophysics Data System (ADS)

Zylstra, A. B.; Yi, S. A.; Haines, B. M.; Olson, R. E.; Leeper, R. J.; Braun, T.; Biener, J.; Kline, J. L.; Batha, S. H.; Berzak Hopkins, L.; Bhandarkar, S.; Bradley, P. A.; Crippen, J.; Farrell, M.; Fittinghoff, D.; Herrmann, H. W.; Huang, H.; Khan, S.; Kong, C.; Kozioziemski, B. J.; Kyrala, G. A.; Ma, T.; Meezan, N. B.; Merrill, F.; Nikroo, A.; Peterson, R. R.; Rice, N.; Sater, J. D.; Shah, R. C.; Stadermann, M.; Volegov, P.; Walters, C.; Wilson, D. C.

2018-05-01

Liquid layer implosions using the "wetted foam" technique, where the liquid fuel is wicked into a supporting foam, have been recently conducted on the National Ignition Facility for the first time [Olson et al., Phys. Rev. Lett. 117, 245001 (2016)]. We report on a series of wetted foam implosions where the convergence ratio was varied between 12 and 20. Reduced nuclear performance is observed as convergence ratio increases. 2-D radiation-hydrodynamics simulations accurately capture the performance at convergence ratios (CR) ˜ 12, but we observe a significant discrepancy at CR ˜ 20. This may be due to suppressed hot-spot formation or an anomalous energy loss mechanism.

Multiple episodes of partial melting, depletion, metasomatism and enrichment processes recorded in the heterogeneous upper mantle sequence of the Neotethyan Eldivan ophiolite, Turkey

NASA Astrophysics Data System (ADS)

Uysal, Ibrahim; Ersoy, E. Yalçın; Dilek, Yildirim; Kapsiotis, Argyrios; Sarıfakıoğlu, Ender

2016-03-01

The Eldivan ophiolite along the Izmir-Ankara-Erzincan suture zone in north-central Anatolia represents a remnant of the Neotethyan oceanic lithosphere. Its upper mantle peridotites include three lithologically and compositionally distinct units: clinopyroxene (cpx)-harzburgite and lherzolite (Group-1), depleted harzburgite (Group-2), and dunite (Group-3). Relics of primary olivine and pyroxene occur in the less refractory harzburgites, and fresh chromian spinel (Cr-spinel) is ubiquitous in all peridotites. The Eldivan peridotites reflect a petrogenetic history evolving from relatively fertile (lherzolite and cpx-harzburgite) toward more depleted (dunite) compositions through time, as indicated by (i) a progressive decrease in the modal cpx distribution, (ii) a progressive increase in the Cr#s [Cr / (Cr + Al)] of Cr-spinel (0.15-0.78), and (iii) an increased depletion in the whole-rock abundances of some magmaphile major oxides (Al2O3, CaO, SiO2 and TiO2) and incompatible trace elements (Zn, Sc, V and Y). The primitive mantle-normalized REE patterns of the Group-1 and some of the Group-2 peridotites display LREE depletions. Higher YbN and lower SmN/YbN ratios of these rocks are compatible with their formation after relatively low degrees (9-25%) of open-system dynamic melting (OSDM) of a Depleted Mid-ocean ridge Mantle (DMM) source, which was then fluxed with small volumes of oceanic mantle-derived melt [fluxing ratio (β): 0.7-1.2%]. Accessory Cr-spinel compositions (Cr# = 015-0.53) of these rocks are consistent with their origin as residual peridotites beneath a mid-ocean ridge axis. Part of the Group-2 harzburgites exhibit lower YbN and higher SmN/YbN ratios, LREE-enriched REE patterns, and higher Cr-spinel Cr#s ranging between 0.54 and 0.61. Trace element compositions of these peridotites can be modeled by approximately 15% OSDM of a previously 17% depleted DMM, which was then fluxed (β: 0.4%) with subduction-influenced melt. The Group-3 dunite samples contain Cr-spinel with elevated Cr#s (0.73-0.78) and low-TiO2 contents (< 0.13 wt.%), implying higher degrees of melting (21-24%) of an already depleted DMM that was triggered by infiltration of low-Ti boninite melt with fluxing rates of 0.4-4.0%. The existence of interstitial, idiomorphic Cr-spinel (high Cr# and low Ti) in the Group-3 dunites is consistent with this interpretation. The occurrence of both MOR- and SSZ-type peridotites in the Eldivan ophiolite suggests that its heterogeneous upper mantle was produced as a result of different partial melting and melt-rock reaction processes in different tectonic settings within the Neotethyan realm.

Research on the hot deformation behavior of a Fe-Ni-Cr alloy (800H) at temperatures above 1000 °C

NASA Astrophysics Data System (ADS)

Cao, Yu; Di, Hongshuang

2015-10-01

Considering the pinning effect of fine carbides on grain boundaries, hot compression tests were performed above the dissolution temperature of Cr23C6 to investigate the hot deformation behavior of a Fe-Ni-Cr alloy (800H). The results show that the single peak stress associated with dynamic recrystalization (DRX) became more distinct at higher temperature and lower strain rate. The process of DRX was thoroughly stimulated when deformed above 1000 °C. Constitutive equations for hot deformation were established by regression analysis of conventional hyperbolic sine equation. The relationships between Zener-Hollomon parameter (Z) and the characteristic points of flow curves were established using the power law relation. Furthermore, kernel average misorientation (KAM) and grain orientation spread (GOS) were used to map the distribution of local misorientation and estimate the fraction of DRX, respectively. The critical strain and peak strain were used to predict the kinetics of DRX with the Avrami-type equation.