Flood-inundation maps and updated components for a flood-warning system or the City of Marietta, Ohio and selected communities along the Lower Muskingum River and Ohio River

USGS Publications Warehouse

Whitehead, Matthew T.; Ostheimer, Chad J.

2014-01-01

Flood profiles for selected reaches were prepared by calibrating steady-state step-backwater models to selected streamgage rating curves. The step-backwater models were used to determine water-surface-elevation profiles for up to 12 flood stages at a streamgage with corresponding stream-flows ranging from approximately the 10- to 0.2-percent chance annual-exceedance probabilities for each of the 3 streamgages that correspond to the flood-inundation maps. Additional hydraulic modeling was used to account for the effects of backwater from the Ohio River on water levels in the Muskingum River. The computed longitudinal profiles of flood levels were used with a Geographic Information System digital elevation model (derived from light detection and ranging) to delineate flood-inundation areas. Digital maps showing flood-inundation areas overlain on digital orthophotographs were prepared for the selected floods.

Fifty-year flood-inundation maps for Tocoa, Honduras

USGS Publications Warehouse

Kresch, David L.; Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of the 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the municipality of Tocoa that would be inundated by a 50-year flood of Rio Tocoa. Geographic Information System (GIS) coverages of the flood inundation are available on a computer in the municipality of Tocoa as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the flood inundation in much more detail than is possible using the maps in this report. Water-surface elevations for an estimated 50-year-flood on Rio Tocoa at Tocoa were estimated using HEC-RAS, a one-dimensional, steady-flow, step-backwater computer program. The channel and floodplain cross sections used in HEC-RAS were developed from an airborne light-detection-and-ranging (LIDAR) topographic survey of the area and a ground survey at one bridge. There are no nearby long-term stream-gaging stations on Rio Tocoa; therefore, the 50-year-flood discharge for Rio Tocoa, 552 cubic meters per second, was estimated using a regression equation that relates the 50-year-flood discharge to drainage area and mean annual precipitation. The drainage area and mean annual precipitation estimated for Rio Tocoa at Tocoa are 204 square kilometers and 1,987 millimeters, respectively. It was assumed that a portion of the 50-year flood, 200 cubic meters per second, would escape the main channel and flow down a side channel before re-entering the main channel again near the lower end of the study area.

Assessing Landslide Mobility Using GIS: Application to Kosrae, Micronesia

NASA Astrophysics Data System (ADS)

Reid, M. E.; Brien, D. L.; Godt, J.; Schmitt, R. G.; Harp, E. L.

2015-12-01

Deadly landslides are often mobile landslides, as exemplified by the disastrous landslide that occurred near Oso, Washington in 2014 killing 43. Despite this association, many landslide susceptibility maps do not identify runout areas. We developed a simple, GIS-based method for identifying areas potentially overrun by mobile slides and debris flows. Our method links three processes within a DEM landscape: landslide initiation, transport, and debris-flow inundation (from very mobile slides). Given spatially distributed shear strengths, we first identify initiation areas using an infinite-slope stability analysis. We then delineate transport zones, or regions of potential entrainment and/or deposition, using a height/length runout envelope. Finally, where these transport zones intersect the channel network, we start debris-flow inundation zones. The extent of inundation is computed using the USGS model Laharz, modified to include many debris-flow locations throughout a DEM. Potential debris-flow volumes are computed from upslope initiation areas and typical slide thicknesses. We applied this approach to the main island of Kosrae State, Federated States of Micronesia (FSM). In 2002, typhoon Chata'an triggered numerous landslides on the neighboring islands of Chuuk State, FSM, resulting in 43 fatalities. Using an infinite-slope stability model calibrated to the Chuuk event, we identified potential landslide initiation areas on Kosrae. We then delineated potential transport zones using a 20º runout envelope, based on runout observations from Chuuk. Potential debris-flow inundation zones were then determined using Laharz. Field inspections on Kosrae revealed that our resulting susceptibility map correctly classified areas covered by previous debris-flow deposits and did not include areas covered by fluvial deposits. Our map has the advantage of providing a visual tool to portray initiation, transport, and runout zones from mobile landslides.

a Novel Methodology for Developing Inundation Maps Under Climate Change Scenarios Using One-Dimensional Model

NASA Astrophysics Data System (ADS)

Vu, M. T.; Liong, S. Y.; Raghavan, V. S.; Liew, S. C.

2011-07-01

Climate change is expected to cause increases in extreme climatic events such as heavy rainstorms and rising tidal level. Heavy rainstorms are known to be serious causes of flooding problems in big cities. Thus, high density residential and commercial areas along the rivers are facing risks of being flooded. For that reason, inundated area determination is now being considered as one of the most important areas of research focus in flood forecasting. In such a context, this paper presents the development of a floodmap in determining flood-prone areas and its volumes. The areas and volumes of flood are computed by the inundated level using the existing digital elevation model (DEM) of a hypothetical catchment chosen for study. The study focuses on the application of Flood Early Warning System (Delft — FEWS, Deltares), which is designated to work with the SOBEK (Delft) to simulate the extent of stormwater on the ground surface. The results from FEWS consist of time-series of inundation maps in Image file format (PNG) and ASCII format, which are subsequently imported to ArcGIS for further calculations. In addition, FEWS results provide options to export the video clip of water spreading out over the catchment. Consequently, inundated area and volume will be determined by the water level on the ground. Final floodmap is displayed in colors created by ArcGIS. Various flood map results corresponding to climate change scenarios will be displayed in the main part of the paper.

Extent of areal inundation of riverine wetlands along Cypress Creek and the Peace, Alafia, North Prong Alafia, and South Prong Alafia Rivers, west-central Florida

USGS Publications Warehouse

Lewelling, B.R.

2003-01-01

Riverine and palustrine system wetlands are a major ecological component of river basins in west-central Florida. Healthy wetlands are dependent upon the frequency and duration of periodic flooding or inundation. This report assesses the extent, area, depth, frequency, and duration of periodic flooding and the effects of potential surface-water withdrawals on the wetlands along Cypress Creek and the Peace, Alafia, North Prong Alafia, and South Prong Alafia Rivers. Results of the study were derived from step-backwater analysis performed at each of the rivers using the U.S. Army Corps of Engineers Hydrologic Engineering Center-River Analysis System (HEC-RAS) one-dimensional model. The step-backwater analysis was performed using selected daily mean discharges at the 10th, 50th, 70th, 80th, 90th, 98th, 99.5th, and 99.9th percentiles to compute extent of areal inundation, area of inundation, and hydraulic depth to assess the net reduction of areal inundation if 10 percent of the total river flow were diverted for potential withdrawals. The extent of areal inundation is determined by cross-sectional topography and the degree to which the channel is incised. Areal inundation occurs along the broad, low relief of the Cypress Creek floodplain during all selected discharge percentiles. However, areal inundation of the Peace and Alafia Rivers floodplains, which generally have deeply incised channels, occurs at or above discharges at the 80th percentile. The greatest area of inundation along the three rivers generally occurs between the 90th and 98th percentile discharges. The decrease in inundated area resulting from a potential 10-percent withdrawal in discharge ranged as follows: Cypress Creek, 22 to 395 acres (1.7 to 8.4 percent); Peace River, 17 to 1,900 acres (2.1 to 13.6 percent); Alafia River, 1 to 90 acres (1 to 19.6 percent); North Prong Alafia River, 1 to 46 acres (0.7 to 23.4 percent); and South Prong Alafia River, 1 to 75 acres (1.5 to 13.4 percent).

Fifty-year flood-inundation maps for Tegucigalpa, Honduras

USGS Publications Warehouse

Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of the 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the municipality of Tegucigalpa that would be inundated by a 50-year flood of Rio Choluteca, Rio Grande, Rio Guacerique, and Rio Chiquito. Geographic Information System (GIS) coverages of the flood inundation are available on a computer in the municipality of Tegucigalpa as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the flood inundation in much more detail than is possible using the maps in this report. Water-surface elevations for an estimated 50-year-flood on Rio Choluteca, Rio Grande, Rio Guacerique, and Rio Chiquito at Tegucigalpa were determined using HEC-RAS, a one-dimensional, steady-flow, step-backwater computer program. The channel and floodplain cross sections used in HEC-RAS were developed from an airborne light-detection-and-ranging (LIDAR) topographic survey of the area and ground surveys at bridges. There are no nearby long-term stream-gaging stations; therefore, the 50-year-flood discharges were estimated using a regression equation that relates the 50-year-flood discharge to drainage area and mean annual precipitation. The estimated 50-year-flood discharge is 922 cubic meters per second at Rio Choluteca at downstream end of the study area boundary, 663 cubic meters per second at the mouth of the Rio Grande, 475 cubic meters per second at the mouth of the Rio Guacerique, and 254 cubic meters per second at the mouth of the Rio Chiquito.

Regional early flood warning system: design and implementation

NASA Astrophysics Data System (ADS)

Chang, L. C.; Yang, S. N.; Kuo, C. L.; Wang, Y. F.

2017-12-01

This study proposes a prototype of the regional early flood inundation warning system in Tainan City, Taiwan. The AI technology is used to forecast multi-step-ahead regional flood inundation maps during storm events. The computing time is only few seconds that leads to real-time regional flood inundation forecasting. A database is built to organize data and information for building real-time forecasting models, maintaining the relations of forecasted points, and displaying forecasted results, while real-time data acquisition is another key task where the model requires immediately accessing rain gauge information to provide forecast services. All programs related database are constructed in Microsoft SQL Server by using Visual C# to extracting real-time hydrological data, managing data, storing the forecasted data and providing the information to the visual map-based display. The regional early flood inundation warning system use the up-to-date Web technologies driven by the database and real-time data acquisition to display the on-line forecasting flood inundation depths in the study area. The friendly interface includes on-line sequentially showing inundation area by Google Map, maximum inundation depth and its location, and providing KMZ file download of the results which can be watched on Google Earth. The developed system can provide all the relevant information and on-line forecast results that helps city authorities to make decisions during typhoon events and make actions to mitigate the losses.

Development of a flood-warning network and flood-inundation mapping for the Blanchard River in Ottawa, Ohio

USGS Publications Warehouse

Whitehead, Matthew T.

2011-01-01

Digital flood-inundation maps of the Blanchard River in Ottawa, Ohio, were created by the U.S. Geological Survey (USGS) in cooperation with the U.S. Department of Agriculture, Natural Resources Conservation Service and the Village of Ottawa, Ohio. The maps, which correspond to water levels (stages) at the USGS streamgage at Ottawa (USGS streamgage site number 04189260), were provided to the National Weather Service (NWS) for incorporation into a Web-based flood-warning Network that can be used in conjunction with NWS flood-forecast data to show areas of predicted flood inundation associated with forecasted flood-peak stages. Flood profiles were computed by means of a step-backwater model calibrated to recent field measurements of streamflow. The step-backwater model was then used to determine water-surface-elevation profiles for 12 flood stages with corresponding streamflows ranging from less than the 2-year and up to nearly the 500-year recurrence-interval flood. The computed flood profiles were used in combination with digital elevation data to delineate flood-inundation areas. Maps of the Village of Ottawa showing flood-inundation areas overlain on digital orthophotographs are presented for the selected floods. As part of this flood-warning network, the USGS upgraded one streamgage and added two new streamgages, one on the Blanchard River and one on Riley Creek, which is tributary to the Blanchard River. The streamgage sites were equipped with both satellite and telephone telemetry. The telephone telemetry provides dual functionality, allowing village officials and the public to monitor current stage conditions and enabling the streamgage to call village officials with automated warnings regarding flood stage and/or predetermined rates of stage increase. Data from the streamgages serve as a flood warning that emergency management personnel can use in conjunction with the flood-inundation maps by to determine a course of action when flooding is imminent.

Fifty-year flood-inundation maps for Choluteca, Honduras

USGS Publications Warehouse

Kresch, David L.; Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the municipality of Choluteca that would be inundated by 50-year floods on Rio Choluteca and Rio Iztoca. Geographic Information System (GIS) coverages of the flood inundation are available on a computer in the municipality of Choluteca as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the flood inundation in much more detail than is possible using the maps in this report. Water-surface elevations for 50-year-floods on Rio Choluteca and Rio Iztoca at Choluteca were estimated using HEC-RAS, a one-dimensional, steady-flow, step-backwater computer program. The channel and floodplain cross sections used in HEC-RAS were developed from an airborne light-detection-and-ranging (LIDAR) topographic survey of the area. The estimated 50-year-flood discharge for Rio Choluteca at Choluteca is 4,620 cubic meters per second, which is the drainage-area-adjusted weighted-average of two independently estimated 50-year-flood discharges for the gaging station Rio Choluteca en Puente Choluteca. One discharge, 4,913 cubic meters per second, was estimated from a frequency analysis of the 17 years of peak discharge record for the gage, and the other, 2,650 cubic meters per second, was estimated from a regression equation that relates the 50-year-flood discharge to drainage area and mean annual precipitation. The weighted-average of the two discharges at the gage is 4,530 cubic meters per second. The 50-year-flood discharge for the study area reach of Rio Choluteca was estimated by multiplying the weighted discharge at the gage by the ratio of the drainage areas upstream from the two locations. The 50-year-flood discharge for Rio Iztoca, which was estimated from the regression equation, is 430 cubic meters per second.

Estimated flood-inundation maps for Cowskin Creek in western Wichita, Kansas

USGS Publications Warehouse

Studley, Seth E.

2003-01-01

The October 31, 1998, flood on Cowskin Creek in western Wichita, Kansas, caused millions of dollars in damages. Emergency management personnel and flood mitigation teams had difficulty in efficiently identifying areas affected by the flooding, and no warning was given to residents because flood-inundation information was not available. To provide detailed information about future flooding on Cowskin Creek, high-resolution estimated flood-inundation maps were developed using geographic information system technology and advanced hydraulic analysis. Two-foot-interval land-surface elevation data from a 1996 flood insurance study were used to create a three-dimensional topographic representation of the study area for hydraulic analysis. The data computed from the hydraulic analyses were converted into geographic information system format with software from the U.S. Army Corps of Engineers' Hydrologic Engineering Center. The results were overlaid on the three-dimensional topographic representation of the study area to produce maps of estimated flood-inundation areas and estimated depths of water in the inundated areas for 1-foot increments on the basis of stream stage at an index streamflow-gaging station. A Web site (http://ks.water.usgs.gov/Kansas/cowskin.floodwatch) was developed to provide the public with information pertaining to flooding in the study area. The Web site shows graphs of the real-time streamflow data for U.S. Geological Survey gaging stations in the area and monitors the National Weather Service Arkansas-Red Basin River Forecast Center for Cowskin Creek flood-forecast information. When a flood is forecast for the Cowskin Creek Basin, an estimated flood-inundation map is displayed for the stream stage closest to the National Weather Service's forecasted peak stage. Users of the Web site are able to view the estimated flood-inundation maps for selected stages at any time and to access information about this report and about flooding in general. Flood recovery teams also have the ability to view the estimated flood-inundation map pertaining to the most recent flood. The availability of these maps and the ability to monitor the real-time stream stage through the U.S. Geological Survey Web site provide emergency management personnel and residents with information that is critical for evacuation and rescue efforts in the event of a flood as well as for post-flood recovery efforts.

Fifty-year flood-inundation maps for Comayagua, Hondura

USGS Publications Warehouse

Kresch, David L.; Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of the 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the municipality of Comayagua that would be inundated by 50-year floods on Rio Humuya and Rio Majada. Geographic Information System (GIS) coverages of the flood inundation are available on a computer in the municipality of Comayagua as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the flood inundation in much more detail than is possible using the maps in this report. Water-surface elevations for 50-year-floods on Rio Humuya and Rio Majada at Comayagua were estimated using HEC-RAS, a one-dimensional, steady-flow, step-backwater computer program. The channel and floodplain cross sections used in HEC-RAS were developed from an airborne light-detection-and-ranging (LIDAR) topographic survey of the area. The 50-year-flood discharge for Rio Humuya at Comayagua, 1,400 cubic meters per second, was estimated using a regression equation that relates the 50-year-flood discharge to drainage area and mean annual precipitation. The reasonableness of the regression discharge was evaluated by comparing it with drainage-area-adjusted 50-year-flood discharges estimated for three long-term Rio Humuya stream-gaging stations. The drainage-area-adjusted 50-year-flood discharges estimated from the gage records ranged from 946 to 1,365 cubic meters per second. Because the regression equation discharge agrees closely with the high end of the range of discharges estimated from the gaging-station records, it was used for the hydraulic modeling to ensure that the resulting 50-year-flood water-surface elevations would not be underestimated. The 50-year-flood discharge for Rio Majada at Comayagua (230 cubic meters per second) was estimated using the regression equation because there are no long-term gaging-stations on this river from which to estimate the discharge.

Development of flood profiles and flood-inundation maps for the Village of Killbuck, Ohio

USGS Publications Warehouse

Ostheimer, Chad J.

2013-01-01

Digital flood-inundation maps for a reach of Killbuck Creek near the Village of Killbuck, Ohio, were created by the U.S. Geological Survey (USGS), in cooperation with Holmes County, Ohio. The inundation maps depict estimates of the areal extent of flooding corresponding to water levels (stages) at the USGS streamgage Killbuck Creek near Killbuck (03139000) and were completed as part of an update to Federal Emergency Management Agency Flood-Insurance Study. The maps were provided to the National Weather Service (NWS) for incorporation into a Web-based flood-warning system that can be used in conjunction with NWS flood-forecast data to show areas of predicted flood inundation associated with forecasted flood-peak stages. The digital maps also have been submitted for inclusion in the data libraries of the USGS interactive Flood Inundation Mapper. Data from the streamgage can be used by emergency-management personnel, in conjunction with the flood-inundation maps, to help determine a course of action when flooding is imminent. Flood profiles for selected reaches were prepared by calibrating a steady-state step-backwater model to an established streamgage rating curve. The step-backwater model then was used to determine water-surface-elevation profiles for 10 flood stages at the streamgage with corresponding streamflows ranging from approximately the 50- to 0.2-percent annual exceedance probabilities. The computed flood profiles were used in combination with digital elevation data to delineate flood-inundation areas.

Fifty-year flood-inundation maps for La Lima, Honduras

USGS Publications Warehouse

Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of the 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the municipality of La Lima that would be inundated by Rio Chamelecon with a discharge of 500 cubic meters per second, the approximate capacity of the river channel through the city of La Lima. The 50-year flood (2,400 cubic meters per second), the original design flow to be mapped, would inundate the entire area surveyed for this municipality. Because water-surface elevations of the 50-year flood could not be mapped properly without substantially expanding the area of the survey, the available data were used instead to estimate the channel capacity of Rio Chamelecon in La Lima by trial-and-error runs of different flows in a numerical model and to estimate the increase in height of levees needed to contain flows of 1,000 and 2,400 cubic meters per second. Geographic Information System (GIS) coverages of the flood inundation are available on a computer in the municipality of La Lima as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the flood inundation in much more detail than is possible using the maps in this report. Water-surface elevations for various discharges on Rio Chamelecon at La Lima were determined using HEC-RAS, a one-dimensional, steady-flow, step-backwater computer program. The channel and floodplain cross sections used in HEC-RAS were developed from an airborne light-detection-and-ranging (LIDAR) topographic survey of the area and ground surveys at three bridges. Top-of-levee or top-of-channel-bank elevations and locations at the cross sections were critical to estimating the channel capacity of Rio Chamelecon. These elevations and locations are provided along with the water-surface elevations for the 500-cubic-meter-per-second flow of Rio Chamelecon. Also, water-surface elevations of the 1,000 and 2,400 cubic-meter-per-second flows are provided, assuming that the existing levees are raised to contained the flows.

A Pilot Tsunami Inundation Forecast System for Australia

NASA Astrophysics Data System (ADS)

Allen, Stewart C. R.; Greenslade, Diana J. M.

2016-12-01

The Joint Australian Tsunami Warning Centre (JATWC) provides a tsunami warning service for Australia. Warnings are currently issued according to a technique that does not include explicit modelling at the coastline, including any potential coastal inundation. This paper investigates the feasibility of developing and implementing tsunami inundation modelling as part of the JATWC warning system. An inundation model was developed for a site in Southeast Australia, on the basis of the availability of bathymetric and topographic data and observations of past tsunamis. The model was forced using data from T2, the operational deep-water tsunami scenario database currently used for generating warnings. The model was evaluated not only for its accuracy but also for its computational speed, particularly with respect to operational applications. Limitations of the proposed forecast processes in the Australian context and areas requiring future improvement are discussed.

Estimation of a Stopping Criterion for Geophysical Granular Flows Based on Numerical Experimentation

NASA Astrophysics Data System (ADS)

Yu, B.; Dalbey, K.; Bursik, M.; Patra, A.; Pitman, E. B.

2004-12-01

Inundation area may be the most important factor for mitigation of natural hazards related to avalanches, debris flows, landslides and pyroclastic flows. Run-out distance is the key parameter for inundation because the front deposits define the leading edge of inundation. To define the run-out distance, it is necessary to know when a flow stops. Numerical experiments are presented for determining a stopping criterion and exploring the suitability of a Savage-Hutter granular model for computing inundation areas of granular flows. The TITAN2D model was employed to run numerical experiments based on the Savage-Hutter theory. A potentially reasonable stopping criterion was found as a function of dimensionless average velocity, aspect ratio of pile, internal friction angle, bed friction angle and bed slope in the flow direction. Slumping piles on a horizontal surface and geophysical flows over complex topography were simulated. Several mountainous areas, including Colima volcano (MX), Casita (Nic.), Little Tahoma Peak (WA, USA) and the San Bernardino Mountains (CA, USA) were used to simulate geophysical flows. Volcanic block and ash flows, debris avalanches and debris flows occurred in these areas and caused varying degrees of damage. The areas have complex topography, including locally steep open slopes, sinuous channels, and combinations of these. With different topography and physical scaling, slumping piles and geophysical flows have a somewhat different dependence of dimensionless stopping velocity on power-law constants associated with aspect ratio of pile, internal friction angle, bed friction angle and bed slope in the flow direction. Visual comparison of the details of the inundation area obtained from the TITAN2D model with models that contain some form of viscous dissipation point out weaknesses in the model that are not evident by investigation of the stopping criterion alone.

Dynamic models of an earthquake and tsunami offshore Ventura, California

USGS Publications Warehouse

Kenny J. Ryan,; Geist, Eric L.; Barall, Michael; David D. Oglesby,

2015-01-01

The Ventura basin in Southern California includes coastal dip-slip faults that can likely produce earthquakes of magnitude 7 or greater and significant local tsunamis. We construct a 3-D dynamic rupture model of an earthquake on the Pitas Point and Lower Red Mountain faults to model low-frequency ground motion and the resulting tsunami, with a goal of elucidating the seismic and tsunami hazard in this area. Our model results in an average stress drop of 6 MPa, an average fault slip of 7.4 m, and a moment magnitude of 7.7, consistent with regional paleoseismic data. Our corresponding tsunami model uses final seafloor displacement from the rupture model as initial conditions to compute local propagation and inundation, resulting in large peak tsunami amplitudes northward and eastward due to site and path effects. Modeled inundation in the Ventura area is significantly greater than that indicated by state of California's current reference inundation line.

Informatics and computational method for inundation and land use study in Arctic Sea eastern Siberia, Russia

NASA Astrophysics Data System (ADS)

Boori, Mukesh Singh; Choudhary, Komal; Kupriyanov, Alexander; Sugimoto, Atsuko

2016-11-01

Eastern Siberia, Russia is physically and socio-economically vulnerable to accelerated Arctic sea level rise due to low topography, high ecological value, harsh climatic conditions, erosion and flooding of coastal area and destruction of harbor constructions and natural coastal hazards. A 1 to 10m inundation land loss scenarios for surface water and sea level rise (SLR) were developed using digital elevation models of study site topography through remote sensing and GIS techniques by ASTER GDEM and Landsat OLI data. Results indicate that 10.82% (8072.70km2) and 29.73% (22181.19km2) of the area will be lost by flooding at minimum and maximum inundation levels, respectively. The most severely impacted sectors are expected to be the vegetation, wetland and the natural ecosystem. Improved understanding of the extent and response of SLR will help in preparing for mitigation and adaptation.

Flood-inundation maps for the West Branch Delaware River, Delhi, New York, 2012

USGS Publications Warehouse

Coon, William F.; Breaker, Brian K.

2012-01-01

Digital flood-inundation maps for a 5-mile reach of the West Branch Delaware River through the Village and part of the Town of Delhi, New York, were created by the U.S. Geological Survey (USGS) in cooperation with the Village of Delhi, the Delaware County Soil and Water Conservation District, and the Delaware County Planning Department. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the Federal Flood Inundation Mapper Web site at http://wim.usgs.gov/FIMI/FloodInundationMapper.html, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) referenced to the USGS streamgage at West Branch Delaware River upstream from Delhi, N.Y. (station number 01421900). In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model that had been used to produce the flood insurance rate maps for the most recent flood insurance study for the Town and Village of Delhi. This hydraulic model was used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 7 ft or near bankfull to 16 ft, which exceeds the stages that correspond to both the estimated 0.2-percent annual-exceedance-probability flood (500-year recurrence interval flood) and the maximum recorded peak flow. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model, which was derived from Light Detection and Ranging (LiDAR) data with a 1.2-ft (0.61-ft root mean squared error) vertical accuracy and 3.3-ft (1-meter) horizontal resolution, to delineate the area flooded at each water level. A map that was produced using this method to delineate the inundated area for the flood that occurred on August 28, 2011, agreed well with highwater marks that had been located in the field using a global positioning system. The availability of the 10 flood-inundation maps on the USGS Flood Inundation Mapping Science Web site, along with Internet information regarding current stage from the USGS streamgage, will provide emergency management personnel and residents with information that is critical for flood-response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

A Parallel, Multi-Scale Watershed-Hydrologic-Inundation Model with Adaptively Switching Mesh for Capturing Flooding and Lake Dynamics

NASA Astrophysics Data System (ADS)

Ji, X.; Shen, C.

2017-12-01

Flood inundation presents substantial societal hazards and also changes biogeochemistry for systems like the Amazon. It is often expensive to simulate high-resolution flood inundation and propagation in a long-term watershed-scale model. Due to the Courant-Friedrichs-Lewy (CFL) restriction, high resolution and large local flow velocity both demand prohibitively small time steps even for parallel codes. Here we develop a parallel surface-subsurface process-based model enhanced by multi-resolution meshes that are adaptively switched on or off. The high-resolution overland flow meshes are enabled only when the flood wave invades to floodplains. This model applies semi-implicit, semi-Lagrangian (SISL) scheme in solving dynamic wave equations, and with the assistant of the multi-mesh method, it also adaptively chooses the dynamic wave equation only in the area of deep inundation. Therefore, the model achieves a balance between accuracy and computational cost.

Evaluation of airborne lidar elevation surfaces for propagation of coastal inundation: the importance of hydrologic connectivity

USGS Publications Warehouse

Poppenga, Sandra K.; Worstell, Bruce B.

2015-01-01

Detailed information about coastal inundation is vital to understanding dynamic and populated areas that are impacted by storm surge and flooding. To understand these natural hazard risks, lidar elevation surfaces are frequently used to model inundation in coastal areas. A single-value surface method is sometimes used to inundate areas in lidar elevation surfaces that are below a specified elevation value. However, such an approach does not take into consideration hydrologic connectivity between elevation grids cells resulting in inland areas that should be hydrologically connected to the ocean, but are not. Because inland areas that should drain to the ocean are hydrologically disconnected by raised features in a lidar elevation surface, simply raising the water level to propagate coastal inundation will lead to inundation uncertainties. We took advantage of this problem to identify hydrologically disconnected inland areas to point out that they should be considered for coastal inundation, and that a lidar-based hydrologic surface should be developed with hydrologic connectivity prior to inundation analysis. The process of achieving hydrologic connectivity with hydrologic-enforcement is not new, however, the application of hydrologically-enforced lidar elevation surfaces for improved coastal inundation mapping as approached in this research is innovative. In this article, we propagated a high-resolution lidar elevation surface in coastal Staten Island, New York to demonstrate that inland areas lacking hydrologic connectivity to the ocean could potentially be included in inundation delineations. For inland areas that were hydrologically disconnected, we evaluated if drainage to the ocean was evident, and calculated an area exceeding 11 ha (~0.11 km2) that could be considered in inundation delineations. We also assessed land cover for each inland area to determine the type of physical surfaces that would be potentially impacted if the inland areas were considered as part of a coastal inundation. A visual analysis indicated that developed, medium intensity and palustrine forested wetland land cover types would be impacted for those locations. This article demonstrates that hydrologic connectivity is an important factor to consider when inundating a lidar elevation surface. This information is needed for inundation monitoring and management in sensitive coastal regions.

Study on the flood simulation techniques for estimation of health risk in Dhaka city, Bangladesh

NASA Astrophysics Data System (ADS)

Hashimoto, M.; Suetsugi, T.; Sunada, K.; ICRE

2011-12-01

Although some studies have been carried out on the spread of infectious disease with the flooding, the relation between flooding and the infectious expansion has not been clarified yet. The improvement of the calculation precision of inundation and its relation with the infectious disease, surveyed epidemiologically, are therefore investigated in a case study in Dhaka city, Bangladesh. The inundation was computed using a flood simulation model that is numerical 2D-model. The "sensitivity to inundation" of hydraulic factors such as drainage channel, dike, and the building occupied ratio was examined because of the lack of digital data set related to flood simulation. Each element in the flood simulation model was incorporated progressively and results were compared with the calculation result as inspection materials by the inundation classification from the existing study (Mollah et al., 2007). The results show that the influences by ''dyke'' and "drainage channel" factors are remarkable to water level near each facility. The inundation level and duration have influence on wide areas when "building occupied ratio" is also considered. The correlation between maximum inundation depth and health risk (DALY, Mortality, Morbidity) was found, but the validation of the inundation model for this case has not been performed yet. The flood simulation model needs to be validated by observed inundation depth. The drainage facilities such as sewer network or the pumping system will be also considered in the further research to improve the precision of the inundation model.

Laharz_py: GIS tools for automated mapping of lahar inundation hazard zones

USGS Publications Warehouse

Schilling, Steve P.

2014-01-01

Laharz_py is written in the Python programming language as a suite of tools for use in ArcMap Geographic Information System (GIS). Primarily, Laharz_py is a computational model that uses statistical descriptions of areas inundated by past mass-flow events to forecast areas likely to be inundated by hypothetical future events. The forecasts use physically motivated and statistically calibrated power-law equations that each has a form A = cV2/3, relating mass-flow volume (V) to planimetric or cross-sectional areas (A) inundated by an average flow as it descends a given drainage. Calibration of the equations utilizes logarithmic transformation and linear regression to determine the best-fit values of c. The software uses values of V, an algorithm for idenitifying mass-flow source locations, and digital elevation models of topography to portray forecast hazard zones for lahars, debris flows, or rock avalanches on maps. Laharz_py offers two methods to construct areas of potential inundation for lahars: (1) Selection of a range of plausible V values results in a set of nested hazard zones showing areas likely to be inundated by a range of hypothetical flows; and (2) The user selects a single volume and a confidence interval for the prediction. In either case, Laharz_py calculates the mean expected A and B value from each user-selected value of V. However, for the second case, a single value of V yields two additional results representing the upper and lower values of the confidence interval of prediction. Calculation of these two bounding predictions require the statistically calibrated prediction equations, a user-specified level of confidence, and t-distribution statistics to calculate the standard error of regression, standard error of the mean, and standard error of prediction. The portrayal of results from these two methods on maps compares the range of inundation areas due to prediction uncertainties with uncertainties in selection of V values. The Open-File Report document contains an explanation of how to install and use the software. The Laharz_py software includes an example data set for Mount Rainier, Washington. The second part of the documentation describes how to use all of the Laharz_py tools in an example dataset at Mount Rainier, Washington.

Real-time Tsunami Inundation Prediction Using High Performance Computers

NASA Astrophysics Data System (ADS)

Oishi, Y.; Imamura, F.; Sugawara, D.

2014-12-01

Recently off-shore tsunami observation stations based on cabled ocean bottom pressure gauges are actively being deployed especially in Japan. These cabled systems are designed to provide real-time tsunami data before tsunamis reach coastlines for disaster mitigation purposes. To receive real benefits of these observations, real-time analysis techniques to make an effective use of these data are necessary. A representative study was made by Tsushima et al. (2009) that proposed a method to provide instant tsunami source prediction based on achieving tsunami waveform data. As time passes, the prediction is improved by using updated waveform data. After a tsunami source is predicted, tsunami waveforms are synthesized from pre-computed tsunami Green functions of linear long wave equations. Tsushima et al. (2014) updated the method by combining the tsunami waveform inversion with an instant inversion of coseismic crustal deformation and improved the prediction accuracy and speed in the early stages. For disaster mitigation purposes, real-time predictions of tsunami inundation are also important. In this study, we discuss the possibility of real-time tsunami inundation predictions, which require faster-than-real-time tsunami inundation simulation in addition to instant tsunami source analysis. Although the computational amount is large to solve non-linear shallow water equations for inundation predictions, it has become executable through the recent developments of high performance computing technologies. We conducted parallel computations of tsunami inundation and achieved 6.0 TFLOPS by using 19,000 CPU cores. We employed a leap-frog finite difference method with nested staggered grids of which resolution range from 405 m to 5 m. The resolution ratio of each nested domain was 1/3. Total number of grid points were 13 million, and the time step was 0.1 seconds. Tsunami sources of 2011 Tohoku-oki earthquake were tested. The inundation prediction up to 2 hours after the earthquake occurs took about 2 minutes, which would be sufficient for a practical tsunami inundation predictions. In the presentation, the computational performance of our faster-than-real-time tsunami inundation model will be shown, and preferable tsunami wave source analysis for an accurate inundation prediction will also be discussed.

Flood-inundation maps for the Susquehanna River near Harrisburg, Pennsylvania, 2013

USGS Publications Warehouse

Roland, Mark A.; Underwood, Stacey M.; Thomas, Craig M.; Miller, Jason F.; Pratt, Benjamin A.; Hogan, Laurie G.; Wnek, Patricia A.

2014-01-01

A series of 28 digital flood-inundation maps was developed for an approximate 25-mile reach of the Susquehanna River in the vicinity of Harrisburg, Pennsylvania. The study was selected by the U.S. Army Corps of Engineers (USACE) national Silver Jackets program, which supports interagency teams at the state level to coordinate and collaborate on flood-risk management. This study to produce flood-inundation maps was the result of a collaborative effort between the USACE, National Weather Service (NWS), Susquehanna River Basin Commission (SRBC), The Harrisburg Authority, and the U.S. Geological Survey (USGS). These maps are accessible through Web-mapping applications associated with the NWS, SRBC, and USGS. The maps can be used in conjunction with the real-time stage data from the USGS streamgage 01570500, Susquehanna River at Harrisburg, Pa., and NWS flood-stage forecasts to help guide the general public in taking individual safety precautions and will provide local municipal officials with a tool to efficiently manage emergency flood operations and flood mitigation efforts. The maps were developed using the USACE HEC–RAS and HEC–GeoRAS programs to compute water-surface profiles and to delineate estimated flood-inundation areas for selected stream stages. The maps show estimated flood-inundation areas overlaid on high-resolution, georeferenced, aerial photographs of the study area for stream stages at 1-foot intervals between 11 feet and 37 feet (which include NWS flood categories Action, Flood, Moderate, and Major) and the June 24, 1972, peak-of-record flood event at a stage of 33.27 feet at the Susquehanna River at Harrisburg, Pa., streamgage.

Dynamic inundation mapping of Hurricane Harvey flooding in the Houston metro area using hyper-resolution modeling and quantitative image reanalysis

NASA Astrophysics Data System (ADS)

Noh, S. J.; Lee, J. H.; Lee, S.; Zhang, Y.; Seo, D. J.

2017-12-01

Hurricane Harvey was one of the most extreme weather events in Texas history and left significant damages in the Houston and adjoining coastal areas. To understand better the relative impact to urban flooding of extreme amount and spatial extent of rainfall, unique geography, land use and storm surge, high-resolution water modeling is necessary such that natural and man-made components are fully resolved. In this presentation, we reconstruct spatiotemporal evolution of inundation during Hurricane Harvey using hyper-resolution modeling and quantitative image reanalysis. The two-dimensional urban flood model used is based on dynamic wave approximation and 10 m-resolution terrain data, and is forced by the radar-based multisensor quantitative precipitation estimates. The model domain includes Buffalo, Brays, Greens and White Oak Bayous in Houston. The model is simulated using hybrid parallel computing. To evaluate dynamic inundation mapping, we combine various qualitative crowdsourced images and video footages with LiDAR-based terrain data.

Validation of 2D flood models with insurance claims

NASA Astrophysics Data System (ADS)

Zischg, Andreas Paul; Mosimann, Markus; Bernet, Daniel Benjamin; Röthlisberger, Veronika

2018-02-01

Flood impact modelling requires reliable models for the simulation of flood processes. In recent years, flood inundation models have been remarkably improved and widely used for flood hazard simulation, flood exposure and loss analyses. In this study, we validate a 2D inundation model for the purpose of flood exposure analysis at the river reach scale. We validate the BASEMENT simulation model with insurance claims using conventional validation metrics. The flood model is established on the basis of available topographic data in a high spatial resolution for four test cases. The validation metrics were calculated with two different datasets; a dataset of event documentations reporting flooded areas and a dataset of insurance claims. The model fit relating to insurance claims is in three out of four test cases slightly lower than the model fit computed on the basis of the observed inundation areas. This comparison between two independent validation data sets suggests that validation metrics using insurance claims can be compared to conventional validation data, such as the flooded area. However, a validation on the basis of insurance claims might be more conservative in cases where model errors are more pronounced in areas with a high density of values at risk.

Flood inundation extent mapping based on block compressed tracing

NASA Astrophysics Data System (ADS)

Shen, Dingtao; Rui, Yikang; Wang, Jiechen; Zhang, Yu; Cheng, Liang

2015-07-01

Flood inundation extent, depth, and duration are important factors affecting flood hazard evaluation. At present, flood inundation analysis is based mainly on a seeded region-growing algorithm, which is an inefficient process because it requires excessive recursive computations and it is incapable of processing massive datasets. To address this problem, we propose a block compressed tracing algorithm for mapping the flood inundation extent, which reads the DEM data in blocks before transferring them to raster compression storage. This allows a smaller computer memory to process a larger amount of data, which solves the problem of the regular seeded region-growing algorithm. In addition, the use of a raster boundary tracing technique allows the algorithm to avoid the time-consuming computations required by the seeded region-growing. Finally, we conduct a comparative evaluation in the Chin-sha River basin, results show that the proposed method solves the problem of flood inundation extent mapping based on massive DEM datasets with higher computational efficiency than the original method, which makes it suitable for practical applications.

Linking flood peak, flood volume and inundation extent: a DEM-based approach

NASA Astrophysics Data System (ADS)

Rebolho, Cédric; Furusho-Percot, Carina; Blaquière, Simon; Brettschneider, Marco; Andréassian, Vazken

2017-04-01

Traditionally, flood inundation maps are computed based on the Shallow Water Equations (SWE) in one or two dimensions, with various simplifications that have proved to give good results. However, the complexity of the SWEs often requires a numerical resolution which can need long computing time, as well as detailed cross section data: this often results in restricting these models to rather small areas abundant with high quality data. This, along with the necessity for fast inundation mapping, are the reason why rapid inundation models are being designed, working for (almost) any river with a minimum amount of data and, above all, easily available data. Our model tries to follow this path by using a 100m DEM over France from which are extracted a drainage network and the associated drainage areas. It is based on two pre-existing methods: (1) SHYREG (Arnaud et al.,2013), a regionalized approach used to calculate the 2-year and 10-year flood quantiles (used as approximated bankfull flow and maximum discharge, respectively) for each river pixel of the DEM (below a 10 000 km2 drainage area) and (2) SOCOSE (Mailhol,1980), which gives, amongst other things, an empirical formula of a characteristic flood duration (for each pixel) based on catchment area, average precipitation and temperature. An overflow volume for each river pixel is extracted from a triangular shaped synthetic hydrograph designed with SHYREG quantiles and SOCOSE flood duration. The volume is then spread from downstream to upstream one river pixel at a time. When the entire hydrographic network is processed, the model stops and generates a map of potential inundation area associated with the 10-year flood quantile. Our model can also be calibrated using past-events inundation maps by adjusting two parameters, one which modifies the overflow duration, and the other, equivalent to a minimum drainage area for river pixels to be flooded. Thus, in calibration on a sample of 42 basins, the first draft of the model showed a 0.51 median Fit (intersection of simulated and observed areas divided by the union of the two, Bates and De Roo, 2000) and a 0.74 maximum. Obviously, this approach is quite rough, and would require testing on events of homogeneous return periods (which is not the case for now). The next steps in the test and the development of our method include the use of the AIGA distributed model to simulate past-events hydrographs, the search for a new way to automatically approach bankfull flow and the integration of the results in our model to build dynamic maps of the flood. References Arnaud, P., Eglin, Y., Janet, B., and Payrastre, O. (2013). Notice utilisateur : bases de données SHYREG-Débit. Méthode - Performances - Limites. Bates, P. D. and De Roo, A. P. J. (2000). A simple raster-based model for flood inundation simulation. Journal of Hydrology, 236(1-2):54-77. Mailhol, J. (1980). Pour une approche plus réaliste du temps caractéristique de crues des bassins versants. In Actes du Colloque d'Oxford, volume 129, pages 229-237, Oxford. IAHS-AISH.

Assessing Nebraska playa wetland inundation status during 1985-2015 using Landsat data and Google Earth Engine.

PubMed

Tang, Zhenghong; Li, Yao; Gu, Yue; Jiang, Weiguo; Xue, Yuan; Hu, Qiao; LaGrange, Ted; Bishop, Andy; Drahota, Jeff; Li, Ruopu

2016-12-01

Playa wetlands in Nebraska provide globally important habitats for migratory waterfowl. Inundation condition is an important indicator of playa wetland functionality. However, there is a lack of long-term continuous monitoring records for playa wetlands. The objective of this study was to determine a suitable index for Landsat images to map the playa inundation status in March and April during 1985-2015. Four types of spectral indices-negative normalized vegetation index, Normalized Difference Water Index (NDWI), modified NDWI, and Tasseled Cap Wetness-Greenness Difference (TCWGD)-were evaluated to detect playa inundation conditions from Landsat images. The results indicate that the TCWGD is the most suitable index for distinguishing playa inundation status. By using Landsat images and Google Earth Engine, we mapped the spring inundation condition of Nebraska playas during 1985-2015. The results show that the total inundated areas were 176.79 km 2 in spring migratory season, representing 18.92% of the total area of playa wetlands. There were 9898 wetlands inundated at least once in either March or April during the past 30 years, representing 29.41% of a total of 33,659 historical wetlands. After comparing the historical hydric soil footprints and the inundated areas, the results indicate that the hydrological conditions of the majority of playas in Nebraska have changed. The inundated wetlands are candidates for protection and/or partial restoration, and the un-inundated wetlands need more attention for wetland restoration. Wetlands in areas enrolled in conservation easements had a significantly high level of playa inundation status than non-conserved wetlands during spring migratory seasons in the past decades.These conservation easements only count for 4.29% of the total footprint areas, but they have contributed 20.82% of the inundation areas in Nebraska during the past 30 years.

Inundation and Fire Shape the Structure of Riparian Forests in the Pantanal, Brazil

PubMed Central

Arruda, Wellinton de Sá; Oldeland, Jens; Paranhos Filho, Antonio Conceição; Pott, Arnildo; Cunha, Nicolay L.; Ishii, Iria Hiromi; Damasceno-Junior, Geraldo Alves

2016-01-01

Inundation and fire can affect the structure of riparian vegetation in wetlands. Our aim was to verify if there are differences in richness, abundance, basal area, composition and topographic preference of woody species in riparian forests related to the fire history, flooding duration, or the interaction between both. The study was conducted in the riparian forests of the Paraguay River some of which were burned three times between 2001 and 2011. We sampled trees with a girth of at least 5 cm at breast height in 150 5 × 10 m plots (79 burned and 71 unburned). We also measured height of the flood mark and estimated the flooding duration of each plot. We performed Generalized Linear Mixed Models to verify differences in richness, basal area, and abundance of individuals associated to interaction of fire and inundation. We used an analysis of similarity (ANOSIM) and indicator species analysis to identify differences in composition of species and the association with burned and unburned area according to different levels of inundation. Finally, we used a hierarchical set of Generalized Linear Models (GLM), the so-called HOF models, to analyse each species’ specific response to inundation based on topography and to determine their preferred optimal topographic position for both burned as well as unburned areas. Richness was positively associated with elevation only in burned areas while abundance was negatively influenced by inundation only in burned areas. Basal area was negatively associated with time of inundation independent of fire history. There were 15 species which were significant indicators for at least one combination of the studied factors. We found nine species in burned areas and 15 in unburned areas, with response curves in HOF models along the inundation gradient. From these, five species shifted their optimal position along the inundation gradient in burned areas. The interaction of fire and inundation did not appear to affect the basal area, but it did affect the richness, number of individuals, success of some species, and seemed to shape the boundary of these forests as shown by the difference in the positioning of these species along the inundation gradient. PMID:27280879

Inundation and Fire Shape the Structure of Riparian Forests in the Pantanal, Brazil.

PubMed

Arruda, Wellinton de Sá; Oldeland, Jens; Paranhos Filho, Antonio Conceição; Pott, Arnildo; Cunha, Nicolay L; Ishii, Iria Hiromi; Damasceno-Junior, Geraldo Alves

2016-01-01

Inundation and fire can affect the structure of riparian vegetation in wetlands. Our aim was to verify if there are differences in richness, abundance, basal area, composition and topographic preference of woody species in riparian forests related to the fire history, flooding duration, or the interaction between both. The study was conducted in the riparian forests of the Paraguay River some of which were burned three times between 2001 and 2011. We sampled trees with a girth of at least 5 cm at breast height in 150 5 × 10 m plots (79 burned and 71 unburned). We also measured height of the flood mark and estimated the flooding duration of each plot. We performed Generalized Linear Mixed Models to verify differences in richness, basal area, and abundance of individuals associated to interaction of fire and inundation. We used an analysis of similarity (ANOSIM) and indicator species analysis to identify differences in composition of species and the association with burned and unburned area according to different levels of inundation. Finally, we used a hierarchical set of Generalized Linear Models (GLM), the so-called HOF models, to analyse each species' specific response to inundation based on topography and to determine their preferred optimal topographic position for both burned as well as unburned areas. Richness was positively associated with elevation only in burned areas while abundance was negatively influenced by inundation only in burned areas. Basal area was negatively associated with time of inundation independent of fire history. There were 15 species which were significant indicators for at least one combination of the studied factors. We found nine species in burned areas and 15 in unburned areas, with response curves in HOF models along the inundation gradient. From these, five species shifted their optimal position along the inundation gradient in burned areas. The interaction of fire and inundation did not appear to affect the basal area, but it did affect the richness, number of individuals, success of some species, and seemed to shape the boundary of these forests as shown by the difference in the positioning of these species along the inundation gradient.

The hydrogeology of the military inundation at the 1914-1918 Yser front (Belgium)

NASA Astrophysics Data System (ADS)

Vandenbohede, Alexander

2016-03-01

Protection against flooding by the sea, drainage of rainwater and integrated management of groundwater and surface-water resources are key issues in low-lying coastal areas. However, under exceptional circumstances, knowledge to keep coastal areas dry and habitable can be used otherwise. Inundation for military purposes is such an example. The hydrogeology of the inundation at the Yser River, Belgium, during the Great War is studied. The inundation started in October 1914 to stop the German advance and lasted until 1918. A water balance and groundwater model are combined to derive the water balance before and during the inundation and to study the impact on the groundwater system. It is concluded that a number of hydrogeological factors contributed to the effectiveness of the inundation. Most importantly, the low-permeability subsoil facilitated loss of inundation water mainly by evaporation. Further, the normal water management strategy of the area (aimed at evacuating excess water towards the sea) was reversed to keep water between the opposing armies. However, the duration of the inundation meant a reorganization of the drainage of areas not inundated; truly an exercise in integrated water management.

The probability of lava inundation at the proposed and existing Kulani prison sites

USGS Publications Warehouse

Kauahikaua, J.P.; Trusdell, F.A.; Heliker, C.C.

1998-01-01

The State of Hawai`i has proposed building a 2,300-bed medium-security prison about 10 km downslope from the existing Kulani medium-security correctional facility. The proposed and existing facilities lie on the northeast rift zone of Mauna Loa, which last erupted in 1984 in this same general area. We use the best available geologic mapping and dating with GIS software to estimate the average recurrence interval between lava flows that inundate these sites. Three different methods are used to adjust the number of flows exposed at the surface for those flows that are buried to allow a better representation of the recurrence interval. Probabilities are then computed, based on these recurrence intervals, assuming that the data match a Poisson distribution. The probability of lava inundation for the existing prison site is estimated to be 11- 12% in the next 50 years. The probability of lava inundation for the proposed sites B and C are 2- 3% and 1-2%, respectively, in the same period. The probabilities are based on estimated recurrence intervals for lava flows, which are approximately proportional to the area considered. The probability of having to evacuate the prison is certainly higher than the probability of lava entering the site. Maximum warning times between eruption and lava inundation of a site are estimated to be 24 hours for the existing prison site and 72 hours for proposed sites B and C. Evacuation plans should take these times into consideration.

Objective rapid delineation of areas at risk from block-and-ash pyroclastic flows and surges

USGS Publications Warehouse

Widiwijayanti, C.; Voight, B.; Hidayat, D.; Schilling, S.P.

2009-01-01

Assessments of pyroclastic flow (PF) hazards are commonly based on mapping of PF and surge deposits and estimations of inundation limits, and/or computer models of varying degrees of sophistication. In volcanic crises a PF hazard map may be sorely needed, but limited time, exposures, or safety aspects may preclude fieldwork, and insufficient time or baseline data may be available for reliable dynamic simulations. We have developed a statistically constrained simulation model for block-and-ash type PFs to estimate potential areas of inundation by adapting methodology from Iverson et al. (Geol Soc America Bull 110:972-984, (1998) for lahars. The predictive equations for block-and-ash PFs are calibrated with data from several volcanoes and given by A = (0.05 to 0.1) V2/3, B = (35 to 40) V2/3, where A is cross-sectional area of inundation, B is planimetric area and V is deposit volume. The proportionality coefficients were obtained from regression analyses and comparison of simulations to mapped deposits. The method embeds the predictive equations in a GIS program coupled with DEM topography, using the LAHARZ program of Schilling (1998). Although the method is objective and reproducible, any PF hazard zone so computed should be considered as an approximate guide only, due to uncertainties on the coefficients applicable to individual PFs, the authenticity of DEM details, and the volume of future collapses. The statistical uncertainty of the predictive equations, which imply a factor of two or more in predicting A or B for a specified V, is superposed on the uncertainty of forecasting V for the next PF to descend a particular valley. Multiple inundation zones, produced by simulations using a selected range of volumes, partly accommodate these uncertainties. The resulting maps show graphically that PF inundation potentials are highest nearest volcano sources and along valley thalwegs, and diminish with distance from source and lateral distance from thalweg. The model does not explicitly consider dynamic behavior, which can be important. Ash-cloud surge impact limits must be extended beyond PF hazard zones and we provide several approaches to do this. The method has been used to supply PF and surge hazard maps in two crises: Merapi 2006; and Montserrat 2006-2007. ?? Springer-Verlag 2008.

Probabilistically modeling lava flows with MOLASSES

NASA Astrophysics Data System (ADS)

Richardson, J. A.; Connor, L.; Connor, C.; Gallant, E.

2017-12-01

Modeling lava flows through Cellular Automata methods enables a computationally inexpensive means to quickly forecast lava flow paths and ultimate areal extents. We have developed a lava flow simulator, MOLASSES, that forecasts lava flow inundation over an elevation model from a point source eruption. This modular code can be implemented in a deterministic fashion with given user inputs that will produce a single lava flow simulation. MOLASSES can also be implemented in a probabilistic fashion where given user inputs define parameter distributions that are randomly sampled to create many lava flow simulations. This probabilistic approach enables uncertainty in input data to be expressed in the model results and MOLASSES outputs a probability map of inundation instead of a determined lava flow extent. Since the code is comparatively fast, we use it probabilistically to investigate where potential vents are located that may impact specific sites and areas, as well as the unconditional probability of lava flow inundation of sites or areas from any vent. We have validated the MOLASSES code to community-defined benchmark tests and to the real world lava flows at Tolbachik (2012-2013) and Pico do Fogo (2014-2015). To determine the efficacy of the MOLASSES simulator at accurately and precisely mimicking the inundation area of real flows, we report goodness of fit using both model sensitivity and the Positive Predictive Value, the latter of which is a Bayesian posterior statistic. Model sensitivity is often used in evaluating lava flow simulators, as it describes how much of the lava flow was successfully modeled by the simulation. We argue that the positive predictive value is equally important in determining how good a simulator is, as it describes the percentage of the simulation space that was actually inundated by lava.

Flood-inundation maps for the Iroquois River at Rensselaer, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.; Bunch, Aubrey R.

2013-01-01

Digital flood-inundation maps for a 4.0-mile reach of the Iroquois River at Rensselaer, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 05522500, Iroquois River at Rensselaer, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at (http://waterdata.usgs.gov/in/nwis/uv?site_no=05522500). In addition, the National Weather Service (NWS) forecasts flood hydrographs at the Rensselaer streamgage. That forecasted peak-stage information, also available on the Internet (http://water.weather.gov/ahps/), may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the Iroquois River reach by means of a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current (June 27, 2012) stage-discharge relations at USGS streamgage 05522500, Iroquois River at Rensselaer, Ind., and high-water marks from the flood of July 2003. The calibrated hydraulic model was then used to determine nine water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage at Rensselaer, Ind., and forecasted stream stages from the NWS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The assessment of Urban Storm Inundation

NASA Astrophysics Data System (ADS)

Setyandito, Oki; Wijayanti, Yureana; Alwan, Muhammad; Chayati, Cholilul; Meilani

2017-12-01

A Sustainable and integrated plan in order to solve urban storm inundation problem, is an urgent issue in Indonesia. A reliable and complete datasets of urban storm inundation area in Indonesia should become its basis to give clear description of inundation area for formulating the best solution. In this study, Statistics Indonesia data in thirty three provinces were assessed during 2000 until 2012 providing data series of urban flood area, flood frequency and land cover changes. Drainage system condition in big cities should be well understood to ensure its infrastructure condition and performance. If inundation occurred, it can be concluded that there is drainage system problem. Inundation data is also important for drainage system design process in the future. The study result is provided estimation of urban storm inundation area based on calculation of Statistics Indonesia data. Moreover, this study is preceded by analyzing and reviewing the capacity of existing drainage channel, using case study of Mataram, West Nusa Tenggara. Rainfall data was obtained from three rainfall stations surround Mataram City. The storm water quantity was calculated using three different approaches as follows: 1) Rational Method; 2) Summation of existing inundation and surface run off discharge; 3) Discharge calculation from existing channel dimensions. After that, the result of these approaches was compared. The storm water quantity gap was concluded as quantity of inundation. The result shows that 36% of drainage channel in Brenyok Kanan River sub system could not accommodate the storm water runoff in this area, which causing inundation. The redesign of drainage channel using design discharge from Rational Method approach should be performed. Within area with the lowest level topography, a construction of detention or storage pond is essential to prevent inundation in this area. Furthermore, the benefits and drawbacks of the statistics database are discussed. Recommendations include utilizing more refined urban land use typologies that can better represent physical alteration of hydrological pathways

Estimation of sediments in urban drainage areas and relation analysis between sediments and inundation risk using GIS.

PubMed

Moojong, Park; Hwandon, Jun; Minchul, Shin

2008-01-01

Sediments entering the sewer in urban areas reduce the conveyance in sewer pipes, which increases inundation risk. To estimate sediment yields, individual landuse areas in each sub-basin should be obtained. However, because of the complex nature of an urban area, this is almost impossible to obtain manually. Thus, a methodology to obtain individual landuse areas for each sub-basin has been suggested for estimating sediment yields. Using GIS, an urban area is divided into sub-basins with respect to the sewer layout, with the area of individual landuse estimated for each sub-basin. The sediment yield per unit area for each sub-basin is then calculated. The suggested method was applied to the GunJa basin in Seoul. For a relation analysis between sediments and inundation risk, sub-basins were ordered by the sediment yields per unit area and compared with historical inundation areas. From this analysis, sub-basins with higher order were found to match the historical inundation areas. Copyright IWA Publishing 2008.

Fifty-Year Flood-Inundation Maps for Santa Rosa de Aguan, Honduras

USGS Publications Warehouse

Mastin, Mark C.; Olsen, T.D.

2002-01-01

After the devastating floods caused by Hurricane Mitch in 1998, maps of the areas and depths of the 50-year-flood inundation at 15 municipalities in Honduras were prepared as a tool for agencies involved in reconstruction and planning. This report, which is one in a series of 15, presents maps of areas in the coastal municipality of Santa Rosa de Aguan that are prone to oceanic storm-surge flooding and wave action. The 50-year flood on the Rio Aguan (4,270 cubic meters per second), would inundate most of the area surveyed for this municipality and beyond. Therefore a detailed numerical hydraulic model was not developed for this municipality as it was for the others. The 50-year storm surge would likely produce higher water levels than the 50-year flood on the river during normal astronomical tides. The elevation of the 50-year storm surge was estimated to be 4.35 meters above normal sea level, based on hurricane probabilities and published storm-surge elevations associated with various hurricane categories. Flood-inundation maps, including areas of wave-action hazard and a color-shaded elevation map, were created from the available data and the estimated 50-year storm tide. Geographic Information System (GIS) coverages of the hazard areas are available on a computer in the municipality of Santa Rosa de Aguan as part of the Municipal GIS project and on the Internet at the Flood Hazard Mapping Data Web page (http://mitchnts1.cr.usgs.gov/projects/floodhazard.html). These coverages allow users to view the maps in much more detail than is possible using the maps in this report.

An expanded model: flood-inundation maps for the Leaf River at Hattiesburg, Mississippi, 2013

USGS Publications Warehouse

Storm, John B.

2014-01-01

Digital flood-inundation maps for a 6.8-mile reach of the Leaf River at Hattiesburg, Mississippi (Miss.), were created by the U.S. Geological Survey (USGS) in cooperation with the City of Hattiesburg, City of Petal, Forrest County, Mississippi Emergency Management Agency, Mississippi Department of Homeland Security, and the Emergency Management District. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Leaf River at Hattiesburg, Miss. (station no. 02473000). Current conditions for estimating near-real-time areas of inundation by use of USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relations at the Leaf River at Hattiesburg, Miss. streamgage (02473000) and documented high-water marks from recent and historical floods. The hydraulic model was then used to determine 13 water-surface profiles for flood stages at 1.0-foot intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM, derived from light detection and ranging (lidar) data having a 0.6-foot vertical and 9.84-foot horizontal resolution) in order to delineate the area flooded at each water level. Development of the estimated flood inundation maps as described in this report update previously published inundation estimates by including reaches of the Bouie and Leaf Rivers above their confluence. The availability of these maps along with Internet information regarding current stage from USGS streamgages and forecasted stream stages from the NWS provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post flood recovery efforts.

Systematic flood modelling to support flood-proof urban design

NASA Astrophysics Data System (ADS)

Bruwier, Martin; Mustafa, Ahmed; Aliaga, Daniel; Archambeau, Pierre; Erpicum, Sébastien; Nishida, Gen; Zhang, Xiaowei; Pirotton, Michel; Teller, Jacques; Dewals, Benjamin

2017-04-01

Urban flood risk is influenced by many factors such as hydro-meteorological drivers, existing drainage systems as well as vulnerability of population and assets. The urban fabric itself has also a complex influence on inundation flows. In this research, we performed a systematic analysis on how various characteristics of urban patterns control inundation flow within the urban area and upstream of it. An urban generator tool was used to generate over 2,250 synthetic urban networks of 1 km2. This tool is based on the procedural modelling presented by Parish and Müller (2001) which was adapted to generate a broader variety of urban networks. Nine input parameters were used to control the urban geometry. Three of them define the average length, orientation and curvature of the streets. Two orthogonal major roads, for which the width constitutes the fourth input parameter, work as constraints to generate the urban network. The width of secondary streets is given by the fifth input parameter. Each parcel generated by the street network based on a parcel mean area parameter can be either a park or a building parcel depending on the park ratio parameter. Three setback parameters constraint the exact location of the building whithin a building parcel. For each of synthetic urban network, detailed two-dimensional inundation maps were computed with a hydraulic model. The computational efficiency was enhanced by means of a porosity model. This enables the use of a coarser computational grid , while preserving information on the detailed geometry of the urban network (Sanders et al. 2008). These porosity parameters reflect not only the void fraction, which influences the storage capacity of the urban area, but also the influence of buildings on flow conveyance (dynamic effects). A sensitivity analysis was performed based on the inundation maps to highlight the respective impact of each input parameter characteristizing the urban networks. The findings of the study pinpoint which properties of urban networks have a major influence on urban inundation flow, enabling better informed flood-proof urban design. References: Parish, Y. I. H., Muller, P. 2001. Procedural modeling of cities. SIGGRAPH, pp. 301—308. Sanders, B.F., Schubert, J.E., Gallegos, H.A., 2008. Integral formulation of shallow-water equations with anisotropic porosity for urban flood modeling. Journal of Hydrology 362, 19-38. Acknowledgements: The research was funded through the ARC grant for Concerted Research Actions, financed by the Wallonia-Brussels Federation.

Flood evolution assessment and monitoring using hydrological modelling techniques: analysis of the inundation areas at a regional scale

NASA Astrophysics Data System (ADS)

Podhoranyi, M.; Kuchar, S.; Portero, A.

2016-08-01

The primary objective of this study is to present techniques that cover usage of a hydrodynamic model as the main tool for monitoring and assessment of flood events while focusing on modelling of inundation areas. We analyzed the 2010 flood event (14th May - 20th May) that occurred in the Moravian-Silesian region (Czech Republic). Under investigation were four main catchments: Opava, Odra, Olše and Ostravice. Four hydrodynamic models were created and implemented into the Floreon+ platform in order to map inundation areas that arose during the flood event. In order to study the dynamics of the water, we applied an unsteady flow simulation for the entire area (HEC-RAS 4.1). The inundation areas were monitored, evaluated and recorded semi-automatically by means of the Floreon+ platform. We focused on information about the extent and presence of the flood areas. The modeled flooded areas were verified by comparing them with real data from different sources (official reports, aerial photos and hydrological networks). The study confirmed that hydrodynamic modeling is a very useful tool for mapping and monitoring of inundation areas. Overall, our models detected 48 inundation areas during the 2010 flood event.

Calibrating a Rainfall-Runoff and Routing Model for the Continental United States

NASA Astrophysics Data System (ADS)

Jankowfsky, S.; Li, S.; Assteerawatt, A.; Tillmanns, S.; Hilberts, A.

2014-12-01

Catastrophe risk models are widely used in the insurance industry to estimate the cost of risk. The models consist of hazard models linked to vulnerability and financial loss models. In flood risk models, the hazard model generates inundation maps. In order to develop country wide inundation maps for different return periods a rainfall-runoff and routing model is run using stochastic rainfall data. The simulated discharge and runoff is then input to a two dimensional inundation model, which produces the flood maps. In order to get realistic flood maps, the rainfall-runoff and routing models have to be calibrated with observed discharge data. The rainfall-runoff model applied here is a semi-distributed model based on the Topmodel (Beven and Kirkby, 1979) approach which includes additional snowmelt and evapotranspiration models. The routing model is based on the Muskingum-Cunge (Cunge, 1969) approach and includes the simulation of lakes and reservoirs using the linear reservoir approach. Both models were calibrated using the multiobjective NSGA-II (Deb et al., 2002) genetic algorithm with NLDAS forcing data and around 4500 USGS discharge gauges for the period from 1979-2013. Additional gauges having no data after 1979 were calibrated using CPC rainfall data. The model performed well in wetter regions and shows the difficulty of simulating areas with sinks such as karstic areas or dry areas. Beven, K., Kirkby, M., 1979. A physically based, variable contributing area model of basin hydrology. Hydrol. Sci. Bull. 24 (1), 43-69. Cunge, J.A., 1969. On the subject of a flood propagation computation method (Muskingum method), J. Hydr. Research, 7(2), 205-230. Deb, K., Pratap, A., Agarwal, S., Meyarivan, T., 2002. A fast and elitist multiobjective genetic algorithm: NSGA-II, IEEE Transactions on evolutionary computation, 6(2), 182-197.

LiDAR-Derived Flood-Inundation Maps for Real-Time Flood-Mapping Applications, Tar River Basin, North Carolina

USGS Publications Warehouse

Bales, Jerad D.; Wagner, Chad R.; Tighe, Kirsten C.; Terziotti, Silvia

2007-01-01

Flood-inundation maps were created for selected streamgage sites in the North Carolina Tar River basin. Light detection and ranging (LiDAR) data with a vertical accuracy of about 20 centimeters, provided by the Floodplain Mapping Information System of the North Carolina Floodplain Mapping Program, were processed to produce topographic data for the inundation maps. Bare-earth mass point LiDAR data were reprocessed into a digital elevation model with regularly spaced 1.5-meter by 1.5-meter cells. A tool was developed as part of this project to connect flow paths, or streams, that were inappropriately disconnected in the digital elevation model by such features as a bridge or road crossing. The Hydraulic Engineering Center-River Analysis System (HEC-RAS) model, developed by the U.S. Army Corps of Engineers, was used for hydraulic modeling at each of the study sites. Eleven individual hydraulic models were developed for the Tar River basin sites. Seven models were developed for reaches with a single gage, and four models were developed for reaches of the Tar River main stem that receive flow from major gaged tributaries, or reaches in which multiple gages were near one another. Combined, the Tar River hydraulic models included 272 kilometers of streams in the basin, including about 162 kilometers on the Tar River main stem. The hydraulic models were calibrated to the most current stage-discharge relations at 11 long-term streamgages where rating curves were available. Medium- to high-flow discharge measurements were made at some of the sites without rating curves, and high-water marks from Hurricanes Fran and Floyd were available for high-stage calibration. Simulated rating curves matched measured curves over the full range of flows. Differences between measured and simulated water levels for a specified flow were no more than 0.44 meter and typically were less. The calibrated models were used to generate a set of water-surface profiles for each of the 11 modeled reaches at 0.305-meter increments for water levels ranging from bankfull to approximately the highest recorded water level at the downstream-most gage in each modeled reach. Inundated areas were identified by subtracting the water-surface elevation in each 1.5-meter by 1.5-meter grid cell from the land-surface elevation in the cell through an automated routine that was developed to identify all inundated cells hydraulically connected to the cell at the downstream-most gage in the model domain. Inundation maps showing transportation networks and orthoimagery were prepared for display on the Internet. These maps also are linked to the U.S. Geological Survey North Carolina Water Science Center real-time streamflow website. Hence, a user can determine the near real-time stage and water-surface elevation at a U.S. Geological Survey streamgage site in the Tar River basin and link directly to the flood-inundation maps for a depiction of the estimated inundated area at the current water level. Although the flood-inundation maps represent distinct boundaries of inundated areas, some uncertainties are associated with these maps. These are uncertainties in the topographic data for the hydraulic model computational grid and inundation maps, effective friction values (Manning's n), model-validation data, and forecast hydrographs, if used. The Tar River flood-inundation maps were developed by using a steady-flow hydraulic model. This assumption clearly has less of an effect on inundation maps produced for low flows than for high flows when it typically takes more time to inundate areas. A flood in which water levels peak and fall slowly most likely will result in more inundation than a similar flood in which water levels peak and fall quickly. Limitations associated with the steady-flow assumption for hydraulic modeling vary from site to site. The one-dimensional modeling approach used in this study resulted in good agreement between measurements and simulations. T

Fusion of real-time simulation, sensing, and geo-informatics in assessing tsunami impact

NASA Astrophysics Data System (ADS)

Koshimura, S.; Inoue, T.; Hino, R.; Ohta, Y.; Kobayashi, H.; Musa, A.; Murashima, Y.; Gokon, H.

2015-12-01

Bringing together state-of-the-art high-performance computing, remote sensing and spatial information sciences, we establish a method of real-time tsunami inundation forecasting, damage estimation and mapping to enhance disaster response. Right after a major (near field) earthquake is triggered, we perform a real-time tsunami inundation forecasting with use of high-performance computing platform (Koshimura et al., 2014). Using Tohoku University's vector supercomputer, we accomplished "10-10-10 challenge", to complete tsunami source determination in 10 minutes, tsunami inundation modeling in 10 minutes with 10 m grid resolution. Given the maximum flow depth distribution, we perform quantitative estimation of exposed population using census data and mobile phone data, and the numbers of potential death and damaged structures by applying tsunami fragility curve. After the potential tsunami-affected areas are estimated, the analysis gets focused and moves on to the "detection" phase using remote sensing. Recent advances of remote sensing technologies expand capabilities of detecting spatial extent of tsunami affected area and structural damage. Especially, a semi-automated method to estimate building damage in tsunami affected areas is developed using pre- and post-event high-resolution SAR (Synthetic Aperture Radar) data. The method is verified through the case studies in the 2011 Tohoku and other potential tsunami scenarios, and the prototype system development is now underway in Kochi prefecture, one of at-risk coastal city against Nankai trough earthquake. In the trial operation, we verify the capability of the method as a new tsunami early warning and response system for stakeholders and responders.

Flood Inundation Mapping and Management using RISAT-1 derived Flood Inundation Areas, Cartosat-1 DEM and a River Flow Model

NASA Astrophysics Data System (ADS)

Kuldeep, K.; Garg, P. K.; Garg, R. D.

2017-12-01

The frequent occurrence of repeated flood events in many regions of the world causing damage to human life and property has augmented the need for effective flood risk management. Microwave satellite data is becoming an indispensable asset for monitoring of many environmental and climatic applications as numerous space-borne synthetic aperture radar (SAR) sensors are offering the data with high spatial resolutions and multi-polarization capabilities. The implementation and execution of Flood mapping, monitoring and management applications has become easier with the availability of SAR data which has obvious advantages over optical data due to its all weather, day and night capabilities. In this study, the exploitation of the SAR dataset for hydraulic modelling and disaster management has been highlighted using feature extraction techniques for water area identification and water level extraction within the floodplain. The availability of high precision digital elevation model generated from the Cartosat-1 stereo pairs has enhanced the capability of retrieving the water depth maps by incorporating the SAR derived flood extent maps. This paper illustrates the flood event on June 2013 in Yamuna River, Haryana, India. The water surface profile computed by combining the topographic data with the RISAT-1 data accurately reflects the true water line. Water levels that were computed by carrying out the modelling using hydraulic model in HECRAS also suggest that the water surface profiles provided by the combined use of topographic data and SAR accurately reflect the true water line. The proposed approach has also been found better in extraction of inundation within vegetated areas.

Flood-inundation maps for the East Fork White River at Shoals, Indiana

USGS Publications Warehouse

Boldt, Justin A.

2016-05-06

Digital flood-inundation maps for a 5.9-mile reach of the East Fork White River at Shoals, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the East Fork White River at Shoals, Ind. (USGS station number 03373500). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS AHPS site SHLI3). NWS AHPS forecast peak stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.Flood profiles were computed for the East Fork White River reach by means of a one-dimensional, step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the current stage-discharge relation (USGS rating no. 43.0) at USGS streamgage 03373500, East Fork White River at Shoals, Ind. The calibrated hydraulic model was then used to compute 26 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from approximately bankfull (10 ft) to the highest stage of the current stage-discharge rating curve (35 ft). The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM), derived from light detection and ranging (lidar) data, to delineate the area flooded at each water level. The areal extent of the 24-ft flood-inundation map was verified with photographs from a flood event on July 20, 2015.The availability of these maps, along with information on the Internet regarding current stage from the USGS streamgage at East Fork White River at Shoals, Ind., and forecasted stream stages from the NWS AHPS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Comparison of physical and semi-empirical hydraulic models for flood inundation mapping

NASA Astrophysics Data System (ADS)

Tavakoly, A. A.; Afshari, S.; Omranian, E.; Feng, D.; Rajib, A.; Snow, A.; Cohen, S.; Merwade, V.; Fekete, B. M.; Sharif, H. O.; Beighley, E.

2016-12-01

Various hydraulic/GIS-based tools can be used for illustrating spatial extent of flooding for first-responders, policy makers and the general public. The objective of this study is to compare four flood inundation modeling tools: HEC-RAS-2D, Gridded Surface Subsurface Hydrologic Analysis (GSSHA), AutoRoute and Height Above the Nearest Drainage (HAND). There is a trade-off among accuracy, workability and computational demand in detailed, physics-based flood inundation models (e.g. HEC-RAS-2D and GSSHA) in contrast with semi-empirical, topography-based, computationally less expensive approaches (e.g. AutoRoute and HAND). The motivation for this study is to evaluate this trade-off and offer guidance to potential large-scale application in an operational prediction system. The models were assessed and contrasted via comparability analysis (e.g. overlapping statistics) by using three case studies in the states of Alabama, Texas, and West Virginia. The sensitivity and accuracy of physical and semi-eimpirical models in producing inundation extent were evaluated for the following attributes: geophysical characteristics (e.g. high topographic variability vs. flat natural terrain, urbanized vs. rural zones, effect of surface roughness paratermer value), influence of hydraulic structures such as dams and levees compared to unobstructed flow condition, accuracy in large vs. small study domain, effect of spatial resolution in topographic data (e.g. 10m National Elevation Dataset vs. 0.3m LiDAR). Preliminary results suggest that semi-empericial models tend to underestimate in a flat, urbanized area with controlled/managed river channel around 40% of the inundation extent compared to the physical models, regardless of topographic resolution. However, in places where there are topographic undulations, semi-empericial models attain relatively higher level of accuracy than they do in flat non-urbanized terrain.

Development of a hydraulic model and flood-inundation maps for the Wabash River near the Interstate 64 Bridge near Grayville, Illinois

USGS Publications Warehouse

Boldt, Justin A.

2018-01-16

A two-dimensional hydraulic model and digital flood‑inundation maps were developed for a 30-mile reach of the Wabash River near the Interstate 64 Bridge near Grayville, Illinois. The flood-inundation maps, which can be accessed through the U.S. Geological Survey (USGS) Flood Inundation Mapping Science web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Wabash River at Mount Carmel, Ill (USGS station number 03377500). Near-real-time stages at this streamgage may be obtained on the internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS AHPS site MCRI2). The NWS AHPS forecasts peak stage information that may be used with the maps developed in this study to show predicted areas of flood inundation.Flood elevations were computed for the Wabash River reach by means of a two-dimensional, finite-volume numerical modeling application for river hydraulics. The hydraulic model was calibrated by using global positioning system measurements of water-surface elevation and the current stage-discharge relation at both USGS streamgage 03377500, Wabash River at Mount Carmel, Ill., and USGS streamgage 03378500, Wabash River at New Harmony, Indiana. The calibrated hydraulic model was then used to compute 27 water-surface elevations for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from less than the action stage (9 ft) to the highest stage (35 ft) of the current stage-discharge rating curve. The simulated water‑surface elevations were then combined with a geographic information system digital elevation model, derived from light detection and ranging data, to delineate the area flooded at each water level.The availability of these maps, along with information on the internet regarding current stage from the USGS streamgage at Mount Carmel, Ill., and forecasted stream stages from the NWS AHPS, provides emergency management personnel and residents with information that is critical for flood-response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Flood-inundation maps for the Saddle River in Ho-Ho-Kus Borough, the Village of Ridgewood, and Paramus Borough, New Jersey, 2013

USGS Publications Warehouse

Watson, Kara M.; Niemoczynski, Michal J.

2014-01-01

Digital flood-inundation maps for a 5.4-mile reach of the Saddle River in New Jersey from Hollywood Avenue in Ho-Ho-Kus Borough downstream through the Village of Ridgewood and Paramus Borough to the confluence with Hohokus Brook in the Village of Ridgewood were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection (NJDEP). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Saddle River at Ridgewood, New Jersey (station 01390500). Current conditions for estimating near real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/nwis/uv?site_no=01390500 or at the National Weather Services (NWS) Advanced Hydrologic Prediction Service (AHPS) at http://water.weather.gov/ahps2/hydrograph.php?wfo=okx&gage=rwdn4. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation (March 11, 2011) at the USGS streamgage 01390500, Saddle River at Ridgewood, New Jersey. The hydraulic model was then used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum, North American Vertical Datum of 1988 (NAVD 88), and ranging from 5 ft, the NWS “action and minor flood stage”, to 14 ft, which is the maximum extent of the stage-discharge rating and 0.6 ft higher than the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system 3-meter (9.84-ft) digital elevation model derived from Light Detection and Ranging (lidar) data in order to delineate the area flooded at each water level. The availability of these maps along with information on the Internet regarding current stage from the USGS streamgage provides emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures as well as for post-flood recovery efforts.

Flood-inundation maps for the Wabash River at Terre Haute, Indiana

USGS Publications Warehouse

Lombard, Pamela J.

2013-01-01

Digital flood-inundation maps for a 6.3-mi reach of the Wabash River from 0.1 mi downstream of the Interstate 70 bridge to 1.1 miles upstream of the Route 63 bridge, Terre Haute, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to select water levels (stages) at the USGS streamgage Wabash River at Terre Haute (station number 03341500). Current conditions at the USGS streamgage may be obtained on the Internet from the USGS National Water Information System (http://waterdata.usgs.gov/in/nwis/uv/?site_no=03341500&agency_cd=USGS&p"). In addition, the same data are provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps//). Within this system, the NWS forecasts flood hydrographs for the Wabash River at Terre Haute that may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the Wabash River at the Terre Haute streamgage. The hydraulic model was then used to compute 22 water-surface profiles for flood stages at 1-ft interval referenced to the streamgage datum and ranging from bank-full to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data having a 0.37-ft vertical accuracy and a 1.02-ft horizontal accuracy) to delineate the area flooded at each water level. The availability of these maps along with Internet information regarding the current stage from the USGS streamgage and forecasted stream stages from the NWS can provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post flood recovery efforts.

Flood-inundation maps for the Elkhart River at Goshen, Indiana

USGS Publications Warehouse

Strauch, Kellan R.

2013-01-01

The U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs, created digital flood-inundation maps for an 8.3-mile reach of the Elkhart River at Goshen, Indiana, extending from downstream of the Goshen Dam to downstream from County Road 17. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to nine selected water levels (stages) at the USGS streamgage at Elkhart River at Goshen (station number 04100500). Current conditions for the USGS streamgages in Indiana may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, stream stage data have been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the Elkhart River at Goshen streamgage. The hydraulic model was then used to compute nine water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from approximately bankfull (5 ft) to greater than the highest recorded water level (13 ft). The simulated water-surface profiles were then combined with a geographic information system (GIS) digital-elevation model (DEM), derived from Light Detection and Ranging (LiDAR) data having a 0.37-ft vertical accuracy and 3.9-ft horizontal resolution in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for postflood recovery efforts.

Influence of urban pattern on inundation flow in floodplains of lowland rivers.

PubMed

Bruwier, M; Mustafa, A; Aliaga, D G; Archambeau, P; Erpicum, S; Nishida, G; Zhang, X; Pirotton, M; Teller, J; Dewals, B

2018-05-01

The objective of this paper is to investigate the respective influence of various urban pattern characteristics on inundation flow. A set of 2000 synthetic urban patterns were generated using an urban procedural model providing locations and shapes of streets and buildings over a square domain of 1×1km 2 . Steady two-dimensional hydraulic computations were performed over the 2000 urban patterns with identical hydraulic boundary conditions. To run such a large amount of simulations, the computational efficiency of the hydraulic model was improved by using an anisotropic porosity model. This model computes on relatively coarse computational cells, but preserves information from the detailed topographic data through porosity parameters. Relationships between urban characteristics and the computed inundation water depths have been based on multiple linear regressions. Finally, a simple mechanistic model based on two district-scale porosity parameters, combining several urban characteristics, is shown to capture satisfactorily the influence of urban characteristics on inundation water depths. The findings of this study give guidelines for more flood-resilient urban planning. Copyright © 2017 Elsevier B.V. All rights reserved.

Flood-inundation maps for the Wabash River at Lafayette, Indiana

USGS Publications Warehouse

Kim, Moon H.

2018-05-10

Digital flood-inundation maps for an approximately 4.8-mile reach of the Wabash River at Lafayette, Indiana (Ind.) were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03335500, Wabash River at Lafayette, Ind. Current streamflow conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the internet at https://waterdata.usgs.gov/in/nwis/uv?site_no=03335500. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood-warning system (https://water.weather.gov/ahps/). The NWS AHPS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the Wabash River at Lafayette, Ind. NWS AHPS-forecast peak-stage information may be used with the maps developed in this study to show predicted areas of flood inundation.For this study, flood profiles were computed for the Wabash River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03335500, Wabash River at Lafayette, Ind., and high-water marks from the flood of July 2003 (U.S. Army Corps of Engineers [USACE], 2007). The calibrated hydraulic model was then used to determine 23 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system digital elevation model derived from light detection and ranging to delineate the area flooded at each water level. The availability of these maps, along with internet information regarding current stage from the USGS streamgage 03335500, Wabash River at Lafayette, Ind., and forecasted high-flow stages from the NWS AHPS, will provide emergency management personnel and residents with information that is critical for flood-response activities such as evacuations and road closures, and for postflood recovery efforts.

Flood-inundation maps for the North Branch Elkhart River at Cosperville, Indiana

USGS Publications Warehouse

Kim, Moon H.; Johnson, Esther M.

2014-01-01

Digital flood-inundation maps for a reach of the North Branch Elkhart River at Cosperville, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers, Detroit District. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 04100222, North Branch Elkhart River at Cosperville, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/uv?site_no=04100222. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS AHPS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the North Branch Elkhart River at Cosperville, Ind. NWS AHPS-forecast peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the North Branch Elkhart River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 04100222, North Branch Elkhart River at Cosperville, Ind., and preliminary high-water marks from the flood of March 1982. The calibrated hydraulic model was then used to determine four water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM, derived from Light Detection and Ranging [LiDAR]) in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage 04100222, North Branch Elkhart River at Cosperville, Ind., and forecast stream stages from the NWS AHPS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the East Fork White River near Bedford, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for an 1.8-mile reach of the East Fork White River near Bedford, Indiana (Ind.) were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selectedwater levels (stages) at USGS streamgage 03371500, East Fork White River near Bedford, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/uv?site_no=03371500. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages, including the East Fork White River near Bedford, Ind. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the East Fork White River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03371500, East Fork White River near Bedford, Ind., and documented high-water marks from the flood of June 2008. The calibrated hydraulic model was then used to determine 20 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM, derived from Light Detection and Ranging (LiDAR) data having a 0.593-foot vertical accuracy) in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage near Bedford, Ind., and forecasted stream stages from the NWS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for postflood recovery eforts.

Development of flood-inundation maps for the Mississippi River in Saint Paul, Minnesota

USGS Publications Warehouse

Czuba, Christiana R.; Fallon, James D.; Lewis, Corby R.; Cooper, Diane F.

2014-01-01

Digital flood-inundation maps for a 6.3-mile reach of the Mississippi River in Saint Paul, Minnesota, were developed through a multi-agency effort by the U.S. Geological Survey in cooperation with the U.S. Army Corps of Engineers and in collaboration with the National Weather Service. The inundation maps, which can be accessed through the U.S. Geological Survey Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the National Weather Service Advanced Hydrologic Prediction Service site at http://water.weather.gov/ahps/inundation.php, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey streamgage at the Mississippi River at Saint Paul (05331000). The National Weather Service forecasted peak-stage information at the streamgage may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the Mississippi River by means of a one-dimensional step-backwater model. The hydraulic model was calibrated using the most recent stage-discharge relation at the Robert Street location (rating curve number 38.0) of the Mississippi River at Saint Paul (streamgage 05331000), as well as an approximate water-surface elevation-discharge relation at the Mississippi River at South Saint Paul (U.S. Army Corps of Engineers streamgage SSPM5). The model also was verified against observed high-water marks from the recent 2011 flood event and the water-surface profile from existing flood insurance studies. The hydraulic model was then used to determine 25 water-surface profiles for flood stages at 1-foot intervals ranging from approximately bankfull stage to greater than the highest recorded stage at streamgage 05331000. The simulated water-surface profiles were then combined with a geographic information system digital elevation model, derived from high-resolution topography data, to delineate potential areas flooded and to determine the water depths within the inundated areas for each stage at streamgage 05331000. The availability of these maps along with information regarding current stage at the U.S. Geological Survey streamgage and forecasted stages from the National Weather Service provides enhanced flood warning and visualization of the potential effects of a forecasted flood for the city of Saint Paul and its residents. The maps also can aid in emergency management planning and response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Tsunami inundation after the Great East Japan Earthquake and mortality of affected communities.

PubMed

Ishiguro, A; Yano, E

2015-10-01

To examine the relationship between mortality rate and tsunami inundation after the Great East Japan Earthquake (GEJE) in 2011. Cross-sectional study. One hundred and fifty-five town or village sections in Ishinomaki, Myagi Prefecture, were included in this study. Three areas in the city were classified by characteristic landforms: plains area (n = 114), ria coastal area (n = 27) and Kitakami riverside (n = 14). The correlation coefficient between tsunami inundation depth and mortality rate was calculated for each area, and the differences between the areas were examined. Furthermore, multivariate analyses adjusted for the characteristics of the sections were conducted using census data taken before the GEJE. An association was found between inundation depth and mortality rate for Ishinomaki as a whole (r = 0.65, P < 0.001), Kitakami riverside (r = 0.85, P < 0.001) and the plains area (r = 0.75, P < 0.001) in separate analyses. However, no association was detected between inundation depth and mortality rate for the ria coastal area (r = 0.14, P = 0.47). The ria coastal area has good accessibility to the hills and tight bonding between members of the community. These factors seemed to play crucial roles in the lower mortality rate in this area despite the deep inundation. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Tsunami Inundation Mapping for the Upper East Coast of the United States

NASA Astrophysics Data System (ADS)

Tehranirad, B.; Kirby, J. T., Jr.; Callahan, J. A.; Shi, F.; Banihashemi, S.; Grilli, S. T.; Grilli, A. R.; Tajalli Bakhsh, T. S.; O'Reilly, C.

2014-12-01

We describe the modeling of tsunami inundation for the Upper US East Coast (USEC) from Ocean City, MD up to Nantucket, MA. and the development of inundation maps for use in emergency management and hazard analysis. Seven tsunami sources were used as initial conditions in order to develop inundation maps based on a Probable Maximum Tsunami approach. Of the seven, two coseismic sources were used; the first being a large earthquake in the Puerto Rico Trench, in the well-known Caribbean Subduction Zone, and the second, an earthquake close to the Azores Gibraltar plate boundary known as the source of the biggest tsunami recorded in the North Atlantic Basin. In addition, four Submarine Mass Failure (SMF) sources located at different locations on the edge of the shelf break were simulated. Finally, the Cumbre Vieja Volcanic (CVV) collapse, located in the Canary Islands, was studied. For this presentation, we discuss modeling results for nearshore tsunami propagation and onshore inundation. A fully nonlinear Boussinesq model (FUNWAVE-TVD) is used to capture the characteristics of tsunami propagation, both nearshore and inland. In addition to the inundation line as the main result of this work, other tsunami quantities such as inundation depth and maximum velocities will be discussed for the whole USEC area. Moreover, a discussion of most vulnerable areas to a possible tsunami in the USEC will be provided. For example, during the inundation simulation process, it was observed that coastal environments with barrier islands are among the hot spots to be significantly impacted by a tsunami. As a result, areas like western Long Island, NY and Atlantic City, NJ are some of the locations that will get extremely affected in case of a tsunami occurrence in the Atlantic Ocean. Finally, the differences between various tsunami sources modeled here will be presented. Although inundation lines for different sources usually follow a similar pattern, there are clear distinctions between the inundation depth and other tsunami features in different areas. Figure below shows the inundation depth for surrounding area of the Ocean City, MD. Figure (a) and (b) are the envelope inundation depth for SMF and coseismic sources. Figure (C) shows the inundation depth for CVV source, which clearly has the largest magnitude amongst the sources studied for this work.

A satellite and model based flood inundation climatology of Australia

NASA Astrophysics Data System (ADS)

Schumann, G.; Andreadis, K.; Castillo, C. J.

2013-12-01

To date there is no coherent and consistent database on observed or simulated flood event inundation and magnitude at large scales (continental to global). The only compiled data set showing a consistent history of flood inundation area and extent at a near global scale is provided by the MODIS-based Dartmouth Flood Observatory. However, MODIS satellite imagery is only available from 2000 and is hampered by a number of issues associated with flood mapping using optical images (e.g. classification algorithms, cloud cover, vegetation). Here, we present for the first time a proof-of-concept study in which we employ a computationally efficient 2-D hydrodynamic model (LISFLOOD-FP) complemented with a sub-grid channel formulation to generate a complete flood inundation climatology of the past 40 years (1973-2012) for the entire Australian continent. The model was built completely from freely available SRTM-derived data, including channel widths, bank heights and floodplain topography, which was corrected for vegetation canopy height using a global ICESat canopy dataset. Channel hydraulics were resolved using actual channel data and bathymetry was estimated within the model using hydraulic geometry. On the floodplain, the model simulated the flow paths and inundation variables at a 1 km resolution. The developed model was run over a period of 40 years and a floodplain inundation climatology was generated and compared to satellite flood event observations. Our proof-of-concept study demonstrates that this type of model can reliably simulate past flood events with reasonable accuracies both in time and space. The Australian model was forced with both observed flow climatology and VIC-simulated flows in order to assess the feasibility of a model-based flood inundation climatology at the global scale.

Leveraging North Carolina's QL2 Lidar to Quantify Sensitivity of National Water Model Derived Flood Inundation Extent to DEM Resolution

NASA Astrophysics Data System (ADS)

Lovette, J. P.; Lenhardt, W. C.; Blanton, B.; Duncan, J. M.; Stillwell, L.

2017-12-01

The National Water Model (NWM) has provided a novel framework for near real time flood inundation mapping across CONUS at a 10m resolution. In many regions, this spatial scale is quickly being surpassed through the collection of high resolution lidar (1 - 3m). As one of the leading states in data collection for flood inundation mapping, North Carolina is currently improving their previously available 20 ft statewide elevation product to a Quality Level 2 (QL2) product with a nominal point spacing of 0.7 meters. This QL2 elevation product increases the ground points by roughly ten times over the previous statewide lidar product, and by over 250 times when compared to the 10m NED elevation grid. When combining these new lidar data with the discharge estimates from the NWM, we can further improve statewide flood inundation maps and predictions of at-risk areas. In the context of flood risk management, these improved predictions with higher resolution elevation models consistently represent an improvement on coarser products. Additionally, the QL2 lidar also includes coarse land cover classification data for each point return, opening the possibility for expanding analysis beyond the use of only digital elevation models (e.g. improving estimates of surface roughness, identifying anthropogenic features in floodplains, characterizing riparian zones, etc.). Using the NWM Height Above Nearest Drainage approach, we compare flood inundation extents derived from multiple lidar-derived grid resolutions to assess the tradeoff between precision and computational load in North Carolina's coastal river basins. The elevation data distributed through the state's new lidar collection program provide spatial resolutions ranging from 5-50 feet, with most inland areas also including a 3 ft product. Data storage increases by almost two orders of magnitude across this range, as does processing load. In order to further assess the validity of the higher resolution elevation products on flood inundation, we examine the NWM outputs from Hurricane Matthew, which devastated southeastern North Carolina in October 2016. When compared with numerous surveyed high water marks across the coastal plain, this assessment provides insight on the impacts of grid resolution on flood inundation extent.

Flood-inundation maps for a nine-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois

USGS Publications Warehouse

Murphy, Elizabeth A.; Soong, David T.; Sharpe, Jennifer B.

2012-01-01

Digital flood-inundation maps for a 9-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Lake County Stormwater Management Commission and the Villages of Lincolnshire and Riverwoods. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Des Plaines River at Lincolnshire, Illinois (station no. 05528100). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05528100. In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. The NWS forecasted peak-stage information, also shown on the Des Plaines River at Lincolnshire inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine seven water-surface profiles for flood stages at roughly 1-ft intervals referenced to the streamgage datum and ranging from the 50- to 0.2-percent annual exceedance probability flows. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the DuPage River from Plainfield to Shorewood, Illinois, 2013

USGS Publications Warehouse

Murphy, Elizabeth A.; Sharpe, Jennifer B.

2013-01-01

Digital flood-inundation maps for a 15.5-mi reach of the DuPage River from Plainfield to Shorewood, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Will County Stormwater Management Planning Committee. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights or stages) at the USGS streamgage at DuPage River at Shorewood, Illinois (sta. no. 05540500). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05540500. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. The NWS-forecasted peak-stage information, also shown on the DuPage River at Shorewood inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine nine water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from NWS Action stage of 6 ft to the historic crest of 14.0 ft. The simulated water-surface profiles were then combined with a Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Sources of uncertainty in flood inundation maps

USGS Publications Warehouse

Bales, J.D.; Wagner, C.R.

2009-01-01

Flood inundation maps typically have been used to depict inundated areas for floods having specific exceedance levels. The uncertainty associated with the inundation boundaries is seldom quantified, in part, because all of the sources of uncertainty are not recognized and because data available to quantify uncertainty seldom are available. Sources of uncertainty discussed in this paper include hydrologic data used for hydraulic model development and validation, topographic data, and the hydraulic model. The assumption of steady flow, which typically is made to produce inundation maps, has less of an effect on predicted inundation at lower flows than for higher flows because more time typically is required to inundate areas at high flows than at low flows. Difficulties with establishing reasonable cross sections that do not intersect and that represent water-surface slopes in tributaries contribute additional uncertainties in the hydraulic modelling. As a result, uncertainty in the flood inundation polygons simulated with a one-dimensional model increases with distance from the main channel.

New Maximum Tsunami Inundation Maps for Use by Local Emergency Planners in the State of California, USA

NASA Astrophysics Data System (ADS)

Wilson, R. I.; Barberopoulou, A.; Miller, K. M.; Goltz, J. D.; Synolakis, C. E.

2008-12-01

A consortium of tsunami hydrodynamic modelers, geologic hazard mapping specialists, and emergency planning managers is producing maximum tsunami inundation maps for California, covering most residential and transient populated areas along the state's coastline. The new tsunami inundation maps will be an upgrade from the existing maps for the state, improving on the resolution, accuracy, and coverage of the maximum anticipated tsunami inundation line. Thirty-five separate map areas covering nearly one-half of California's coastline were selected for tsunami modeling using the MOST (Method of Splitting Tsunami) model. From preliminary evaluations of nearly fifty local and distant tsunami source scenarios, those with the maximum expected hazard for a particular area were input to MOST. The MOST model was run with a near-shore bathymetric grid resolution varying from three arc-seconds (90m) to one arc-second (30m), depending on availability. Maximum tsunami "flow depth" and inundation layers were created by combining all modeled scenarios for each area. A method was developed to better define the location of the maximum inland penetration line using higher resolution digital onshore topographic data from interferometric radar sources. The final inundation line for each map area was validated using a combination of digital stereo photography and fieldwork. Further verification of the final inundation line will include ongoing evaluation of tsunami sources (seismic and submarine landslide) as well as comparison to the location of recorded paleotsunami deposits. Local governmental agencies can use these new maximum tsunami inundation lines to assist in the development of their evacuation routes and emergency response plans.

Inundation Mapping for Heterogeneous Land Covers with Synthetic Aperture Radar and Auxiliary Data

NASA Astrophysics Data System (ADS)

Aristizabal, F.; Judge, J.

2017-12-01

Synthetic Aperture Radar (SAR) has been widely used to detect surface water inundation and provides an advantage over multi-spectral instruments due to cloud penetration and higher spatial resolutions. However, detecting inundation for densely vegetated and urban areas with SAR remains a challenge due to corner reflection and diffuse scattering. Additionally, flat urban surfaces such as roads exhibit similar backscatter coefficients as urban surface water. Differences between inundated and non-inundated backscatter over vegetated land covers of static spatial domains have been demonstrated in previous studies. However, these backscatter differences are sensitive to changes in water depth, soil moisture, SAR sensor parameters, terrain, and vegetation properties. These factors tend to make accurate inundation mapping of heterogeneous regions across varying spatial and temporal extents difficult with exclusive use of SAR. This study investigates the utility of auxiliary data specifically high-resolution (10m) terrain information in conjunction with SAR (10m) for detecting inundated areas. Digital elevation models provide an absolute elevation which could enhance inundation mapping given a limited study extent with similar topography. To counter this limitation, a hydrologically relevant terrain index is proposed known as the Height Above Nearest Drainage (HAND) which normalizes topography to the local relative elevation of the nearest point along the relevant drainage line. HAND has been used for assisting remote sensing inundation mapping in the pre-processing stage as a terrain correction tool and as a post-processing mask that eliminates areas of low inundation risk. While the latter technique is useful for reduction of commission errors, it does not employ HAND for reducing omission errors that can occur from dense vegetation, spectral noise, and urban features. Sentinel-1 dual-pol SAR as well as auxiliary HAND will be used as predictors by various supervised and unsupervised classification algorithms. The October 2016 record flood caused by Hurricane Matthew along the Neuse River in North Carolina will be used as a study area. For validation, locally inundated areas will be derived from observed river stages and high water marks furnished by the U.S. Geological Survey.

Flood-inundation maps for a 9.1-mile reach of the Coast Fork Willamette River near Creswell and Goshen, Lane County, Oregon

USGS Publications Warehouse

Hess, Glen W.; Haluska, Tana L.

2016-04-13

Digital flood-inundation maps for a 9.1-mile reach of the Coast Fork Willamette River near Creswell and Goshen, Oregon, were developed by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers (USACE). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected stages at the USGS streamgage at Coast Fork Willamette River near Goshen, Oregon (14157500), at State Highway 58. Current stage at the streamgage for estimating near-real-time areas of inundation may be obtained at http://waterdata.usgs.gov/or/nwis/uv/?site_no=14157500&PARAmeter_cd=00065,00060. In addition, the National Weather Service (NWS) forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.In this study, areas of inundation were provided by USACE. The inundated areas were developed from flood profiles simulated by a one-dimensional unsteady step‑backwater hydraulic model. The profiles were checked by the USACE using documented high-water marks from a January 2006 flood. The model was compared and quality assured using several other methods. The hydraulic model was then used to determine eight water-surface profiles at various flood stages referenced to the streamgage datum and ranging from 11.8 to 19.8 ft, approximately 2.6 ft above the highest recorded stage at the streamgage (17.17 ft) since 1950. The intervals between stages are variable and based on annual exceedance probability discharges, some of which approximate NWS action stages.The areas of inundation and water depth grids provided to USGS by USACE were used to create interactive flood‑inundation maps. The availability of these maps with current stage from USGS streamgage and forecasted stream stages from the NWS provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures as well as for post flood recovery efforts.

Global-scale analysis of satellite-derived time series of naturally inundated areas as a basis for floodplain modeling

NASA Astrophysics Data System (ADS)

Adam, L.; Döll, P.; Prigent, C.; Papa, F.

2010-08-01

Floodplains play an important role in the terrestrial water cycle and are very important for biodiversity. Therefore, an improved representation of the dynamics of floodplain water flows and storage in global hydrological and land surface models is required. To support model validation, we combined monthly time series of satellite-derived inundation areas (Papa et al., 2010) with data on irrigated rice areas (Portmann et al., 2010). In this way, we obtained global-scale time series of naturally inundated areas (NIA), with monthly values of inundation extent during 1993-2004 and a spatial resolution of 0.5°. For most grid cells (0.5°×0.5°), the mean annual maximum of NIA agrees well with the static open water extent of the Global Lakes and Wetlands database (GLWD) (Lehner and Döll, 2004), but in 16% of the cells NIA is larger than GLWD. In some regions, like Northwestern Europe, NIA clearly overestimates inundated areas, probably because of confounding very wet soils with inundated areas. In other areas, such as South Asia, it is likely that NIA can help to enhance GLWD. NIA data will be very useful for developing and validating a floodplain modeling algorithm for the global hydrological model WGHM. For example, we found that monthly NIAs correlate with observed river discharges.

Ensemble projection of the sea level rise impact on storm surge and inundation at the coast of Bangladesh

NASA Astrophysics Data System (ADS)

Jisan, Mansur Ali; Bao, Shaowu; Pietrafesa, Leonard J.

2018-01-01

The hydrodynamic model Delft3D is used to study the impact of sea level rise (SLR) on storm surge and inundation in the coastal region of Bangladesh. To study the present-day inundation scenario, the tracks of two known tropical cyclones (TC) were used: Aila (Category 1; 2009) and Sidr (Category 5; 2007). Model results were validated with the available observations. Future inundation scenarios were generated by using the strength of TC Sidr, TC Aila and an ensemble of historical TC tracks but incorporating the effect of SLR. Since future change in storm surge inundation under SLR impact is a probabilistic incident, a probable range of future change in the inundated area was calculated by taking into consideration the uncertainties associated with TC tracks, intensities and landfall timing. The model outputs showed that the inundated area for TC Sidr, which was calculated as 1860 km2, would become 31 % larger than the present-day scenario if a SLR of 0.26 m occurred during the mid-21st-century climate scenario. Similarly to that, an increasing trend was found for the end-21st-century climate scenario. It was found that with a SLR of 0.54 m, the inundated area would become 53 % larger than the present-day case. Along with the inundation area, the impact of SLR was examined for changes in future storm surge level. A significant increase of 14 % was found in storm surge level for the case of TC Sidr at Barisal station if a SLR of 0.26 m occurred in the mid-21st century. Similarly to that, an increase of 29 % was found at storm surge level with a SLR of 0.54 m in this location for the end-21st-century climate scenario. Ensemble projections based on uncertainties of future TC events also showed that, for a change of 0.54 m in SLR, the inundated area would range between 3500 and 3750 km2, whereas for present-day SLR simulations it was found within the range of 1000-1250 km2. These results revealed that even if the future TCs remain at the same strength as at present, the projected changes in SLR will generate more severe threats in terms of surge height and the extent of the inundated area.

Comparison and Computational Performance of Tsunami-HySEA and MOST Models for the LANTEX 2013 scenario

NASA Astrophysics Data System (ADS)

González-Vida, Jose M.; Macías, Jorge; Mercado, Aurelio; Ortega, Sergio; Castro, Manuel J.

2017-04-01

Tsunami-HySEA model is used to simulate the Caribbean LANTEX 2013 scenario (LANTEX is the acronym for Large AtlaNtic Tsunami EXercise, which is carried out annually). The numerical simulation of the propagation and inundation phases, is performed with both models but using different mesh resolutions and nested meshes. Some comparisons with the MOST tsunami model available at the University of Puerto Rico (UPR) are made. Both models compare well for propagating tsunami waves in open sea, producing very similar results. In near-shore shallow waters, Tsunami-HySEA should be compared with the inundation version of MOST, since the propagation version of MOST is limited to deeper waters. Regarding the inundation phase, a 1 arc-sec (approximately 30 m) resolution mesh covering all of Puerto Rico, is used, and a three-level nested meshes technique implemented. In the inundation phase, larger differences between model results are observed. Nevertheless, the most striking difference resides in computational time; Tsunami-HySEA is coded using the advantages of GPU architecture, and can produce a 4 h simulation in a 60 arcsec resolution grid for the whole Caribbean Sea in less than 4 min with a single general-purpose GPU and as fast as 11 s with 32 general-purpose GPUs. In the inundation stage with nested meshes, approximately 8 hours of wall clock time is needed for a 2-h simulation in a single GPU (versus more than 2 days for the MOST inundation, running three different parts of the island—West, Center, East—at the same time due to memory limitations in MOST). When domain decomposition techniques are finally implemented by breaking up the computational domain into sub-domains and assigning a GPU to each sub-domain (multi-GPU Tsunami-HySEA version), we show that the wall clock time significantly decreases, allowing high-resolution inundation modelling in very short computational times, reducing, for example, if eight GPUs are used, the wall clock time to around 1 hour. Besides, these computational times are obtained using general-purpose GPU hardware.

Flood-inundation maps for the Flatrock River at Columbus, Indiana, 2012

USGS Publications Warehouse

Coon, William F.

2013-01-01

Digital flood-inundation maps for a 5-mile reach of the Flatrock River on the western side of Columbus, Indiana, from County Road 400N to the river mouth at the confluence with Driftwood River, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ and the Federal Flood Inundation Mapper Web site at http://wim.usgs.gov/FIMI/FloodInundationMapper.html, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Flatrock River at Columbus (station number 03363900). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service, which also presents the USGS data, at http:/water.weather.gov/ahps/. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation at the Flatrock River streamgage, high-water marks that were surveyed following the flood of June 7, 2008, and water-surface profiles from the current flood-insurance study for the City of Columbus. The hydraulic model was then used to compute 12 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 9 ft or near bankfull to 20 ft, which exceeds the stages that correspond to both the estimated 0.2-percent annual exceedance probability flood (500-year recurrence interval flood) and the maximum recorded peak flow. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from Light Detection and Ranging (LiDAR) data having a 0.37 ft vertical accuracy and 3.9 ft horizontal resolution) to delineate the area flooded at each water level. The availability of these maps on the USGS Federal Flood Inundation Mapper Web site, along with Internet information regarding current stage from the USGS streamgage, will provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation map library for the Licking River and South Fork Licking River near Falmouth, Kentucky

USGS Publications Warehouse

Lant, Jeremiah G.

2016-09-19

Digital flood inundation maps for a 17-mile reach of Licking River and 4-mile reach of South Fork Licking River near Falmouth, Kentucky, were created by the U.S. Geological Survey (USGS) in cooperation with Pendleton County and the U.S. Army Corps of Engineers–Louisville District. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://wim.usgs.gov/FIMI/FloodInundationMapper.html, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Licking River at Catawba, Ky., (station 03253500) and the USGS streamgage on the South Fork Licking River at Hayes, Ky., (station 03253000). Current conditions (2015) for the USGS streamgages may be obtained online at the USGS National Water Information System site (http://waterdata.usgs.gov/nwis). In addition, the streamgage information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The flood hydrograph forecasts provided by the NWS are usually collocated with USGS streamgages. The forecasted peak-stage information, also available on the NWS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.In this study, flood profiles were computed for the Licking River reach and South Fork Licking River reach by using a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current (2015) stage-discharge relations for the Licking River at Catawba, Ky., and the South Fork Licking River at Hayes, Ky., USGS streamgages. The calibrated model was then used to calculate 60 water-surface profiles for a sequence of flood stages, at 2-foot intervals, referenced to the streamgage datum and ranging from an elevation near bankfull to the elevation associated with a major flood that occurred in the region in 1997. To delineate the flooded area at each interval flood stage, the simulated water-surface profiles were combined with a digital elevation model of the study area by using geographic information system software.The availability of these flood inundation maps for Falmouth, Ky., along with online information regarding current stages from the USGS streamgages and forecasted stages from the NWS, provides emergency management personnel and local residents with information that is critical for flood response activities such as evacuations, road closures, and post-flood recovery efforts.

Flood-inundation maps for Suwanee Creek from the confluence of Ivy Creek to the Noblin Ridge Drive bridge, Gwinnett County, Georgia

USGS Publications Warehouse

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 6.9-mile reach of Suwanee Creek, from the confluence of Ivy Creek to the Noblin Ridge Drive bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with Gwinnett County, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Suwanee Creek at Suwanee, Georgia (02334885). Current stage at this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Suwanee Creek at Suwanee (02334885), available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers HEC-RAS software for Suwanee Creek and was used to compute flood profiles for a 6.9-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Suwanee Creek at Suwanee streamgage (02334885). The hydraulic model was then used to determine 19 water-surface profiles for flood stages at the Suwanee Creek streamgage at 0.5-foot intervals referenced to the streamgage. The profiles ranged from just above bankfull stage (7.0 feet) to approximately 1.7 feet above the highest recorded water level at the streamgage (16.0 feet). The simulated water-surface profiles were then combined with a geographic information system digital elevation model - derived from light detection and ranging (LiDAR) data having a 5.0-foot horizontal resolution - to delineate the area flooded for each 0.5-foot increment of stream stage. The availability of these maps, when combined with real-time stage information from USGS streamgages and forecasted stream stage from the NWS, provides emergency management personnel and residents with critical information during flood-response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Modeling Surface Water Dynamics in the Amazon Basin Using Mosart-Inundation-v1.0: Impacts of Geomorphological Parameters and River Flow Representation

NASA Technical Reports Server (NTRS)

Luo, Xiangyu; Li, Hong-Yi; Leung, Ruby; Tesfa, Teklu K.; Getirana, Augusto; Papa, Fabrice; Hess, Laura L.

2017-01-01

Surface water dynamics play an important role in water, energy and carbon cycles of the Amazon Basin. A macro-scale inundation scheme was integrated with a surface-water transport model and the extended model was applied in this vast basin. We addressed the challenges of improving basin-wide geomorphological parameters and river flow representation for 15 large-scale applications. Vegetation-caused biases embedded in the HydroSHEDS DEM data were alleviated by using a vegetation height map of about 1-km resolution and a land cover dataset of about 90-m resolution. The average elevation deduction from the DEM correction was about 13.2 m for the entire basin. Basin-wide empirical formulae for channel cross-sectional geometry were adjusted based on local information for the major portion of the basin, which could significantly reduce the cross-sectional area for the channels of some subregions. The Manning roughness coefficient of the channel 20 varied with the channel depth to reflect the general rule that the relative importance of riverbed resistance in river flow declined with the increase of river size. The entire basin was discretized into 5395 subbasins (with an average area of 1091.7 km2), which were used as computation units. The model was driven by runoff estimates of 14 years (1994 2007) generated by the ISBA land surface model. The simulated results were evaluated against in situ streamflow records, and remotely sensed Envisat altimetry data and GIEMS inundation data. The hydrographs were reproduced fairly well for the majority of 25 13 major stream gauges. For the 11 subbasins containing or close to 11 of the 13 gauges, the timing of river stage fluctuations was captured; for most of the 11 subbasins, the magnitude of river stage fluctuations was represented well. The inundation estimates were comparable to the GIEMS observations. Sensitivity analyses demonstrated that refining floodplain topography, channel morphology and Manning roughness coefficients, as well as accounting for backwater effects could evidently affect local and upstream inundation, which consequently affected flood waves and inundation of the downstream 30 area. It was also shown that the river stage was sensitive to local channel morphology and Manning roughness coefficients, as well as backwater effects. The understanding obtained in this study could be helpful to improving modeling of surface hydrology in basins with evident inundation, especially at regional or larger scales.

Flood-inundation maps for an 8.9-mile reach of the South Fork Little River at Hopkinsville, Kentucky

USGS Publications Warehouse

Lant, Jeremiah G.

2013-01-01

Digital flood-inundation maps for an 8.9-mile reach of South Fork Little River at Hopkinsville, Kentucky, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Hopkinsville Community Development Services. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at South Fork Little River at Highway 68 By-Pass at Hopkinsville, Kentucky (station no. 03437495). Current conditions for the USGS streamgage may be obtained online at the USGS National Water Information System site (http://waterdata.usgs.gov/nwis/inventory?agency_code=USGS&site_no=03437495). In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. The forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the South Fork Little River reach by using HEC-RAS, a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current (2012) stage-discharge relation at the South Fork Little River at Highway 68 By-Pass at Hopkinsville, Kentucky, streamgage and measurements collected during recent flood events. The calibrated model was then used to calculate 13 water-surface profiles for a sequence of flood stages, most at 1-foot intervals, referenced to the streamgage datum and ranging from a stage near bank full to the estimated elevation of the 1.0-percent annual exceedance probability flood at the streamgage. To delineate the flooded area at each interval flood stage, the simulated water-surface profiles were combined with a Digital Elevation Model (DEM) of the study area by using Geographic Information System (GIS) software. The DEM consisted of bare-earth elevations within the study area and was derived from a Light Detection And Ranging (LiDAR) dataset having a 3.28-foot horizontal resolution. These flood-inundation maps, along with online information regarding current stages from USGS streamgage and forecasted stages from the NWS, provide emergency management and local residents with critical information for flood response activities such as evacuations, road closures, and post-flood recovery efforts.

Vulnerability of the Nile Delta coastal areas to inundation by sea level rise.

PubMed

Hassaan, M A; Abdrabo, M A

2013-08-01

Sea level changes are typically caused by several natural phenomena, including ocean thermal expansion, glacial melt from Greenland and Antarctica. Global average sea level is expected to rise, through the twenty-first century, according to the IPCC projections by between 0.18 and 0.59 cm. Such a rise in sea level will significantly impact coastal area of the Nile Delta, consisting generally of lowland and is densely populated areas and accommodates significant proportion of Egypt's economic activities and built-up areas. The Nile Delta has been examined in several previous studies, which worked under various hypothetical sea level rise (SLR) scenarios and provided different estimates of areas susceptible to inundation due to SLR. The paper intends, in this respect, to identify areas, as well as land use/land cover, susceptible to inundation by SLR based upon most recent scenarios of SLR, by the year 2100 using GIS. The results indicate that about 22.49, 42.18, and 49.22 % of the total area of coastal governorates of the Nile Delta would be susceptible to inundation under different scenarios of SLR. Also, it was found that 15.56 % of the total areas of the Nile Delta that would be vulnerable to inundation due to land subsidence only, even in the absence of any rise in sea level. Moreover, it was found that a considerable proportion of these areas (ranging between 32.32 and 53.66 %) are currently either wetland or undeveloped areas. Furthermore, natural and/or man-made structures, such as the banks of the International Coastal Highway, were found to provide unintended protection to some of these areas. This suggests that the inundation impact of SLR on the Nile Delta is less than previously reported.

Relationship between the Prediction Accuracy of Tsunami Inundation and Relative Distribution of Tsunami Source and Observation Arrays: A Case Study in Tokyo Bay

NASA Astrophysics Data System (ADS)

Takagawa, T.

2017-12-01

A rapid and precise tsunami forecast based on offshore monitoring is getting attention to reduce human losses due to devastating tsunami inundation. We developed a forecast method based on the combination of hierarchical Bayesian inversion with pre-computed database and rapid post-computing of tsunami inundation. The method was applied to Tokyo bay to evaluate the efficiency of observation arrays against three tsunamigenic earthquakes. One is a scenario earthquake at Nankai trough and the other two are historic ones of Genroku in 1703 and Enpo in 1677. In general, rich observation array near the tsunami source has an advantage in both accuracy and rapidness of tsunami forecast. To examine the effect of observation time length we used four types of data with the lengths of 5, 10, 20 and 45 minutes after the earthquake occurrences. Prediction accuracy of tsunami inundation was evaluated by the simulated tsunami inundation areas around Tokyo bay due to target earthquakes. The shortest time length of accurate prediction varied with target earthquakes. Here, accurate prediction means the simulated values fall within the 95% credible intervals of prediction. In Enpo earthquake case, 5-minutes observation is enough for accurate prediction for Tokyo bay, but 10-minutes and 45-minutes are needed in the case of Nankai trough and Genroku, respectively. The difference of the shortest time length for accurate prediction shows the strong relationship with the relative distance from the tsunami source and observation arrays. In the Enpo case, offshore tsunami observation points are densely distributed even in the source region. So, accurate prediction can be rapidly achieved within 5 minutes. This precise prediction is useful for early warnings. Even in the worst case of Genroku, where less observation points are available near the source, accurate prediction can be obtained within 45 minutes. This information can be useful to figure out the outline of the hazard in an early stage of reaction.

Probabilistic Risk Analysis of Run-up and Inundation in Hawaii due to Distant Tsunamis

NASA Astrophysics Data System (ADS)

Gica, E.; Teng, M. H.; Liu, P. L.

2004-12-01

Risk assessment of natural hazards usually includes two aspects, namely, the probability of the natural hazard occurrence and the degree of damage caused by the natural hazard. Our current study is focused on the first aspect, i.e., the development and evaluation of a methodology that can predict the probability of coastal inundation due to distant tsunamis in the Pacific Basin. The calculation of the probability of tsunami inundation could be a simple statistical problem if a sufficiently long record of field data on inundation was available. Unfortunately, such field data are very limited in the Pacific Basin due to the reason that field measurement of inundation requires the physical presence of surveyors on site. In some areas, no field measurements were ever conducted in the past. Fortunately, there are more complete and reliable historical data on earthquakes in the Pacific Basin partly because earthquakes can be measured remotely. There are also numerical simulation models such as the Cornell COMCOT model that can predict tsunami generation by an earthquake, propagation in the open ocean, and inundation onto a coastal land. Our objective is to develop a methodology that can link the probability of earthquakes in the Pacific Basin with the inundation probability in a coastal area. The probabilistic methodology applied here involves the following steps: first, the Pacific Rim is divided into blocks of potential earthquake sources based on the past earthquake record and fault information. Then the COMCOT model is used to predict the inundation at a distant coastal area due to a tsunami generated by an earthquake of a particular magnitude in each source block. This simulation generates a response relationship between the coastal inundation and an earthquake of a particular magnitude and location. Since the earthquake statistics is known for each block, by summing the probability of all earthquakes in the Pacific Rim, the probability of the inundation in a coastal area can be determined through the response relationship. Although the idea of the statistical methodology applied here is not new, this study is the first to apply it to study the probability of inundation caused by earthquake-generated distant tsunamis in the Pacific Basin. As a case study, the methodology is applied to predict the tsunami inundation risk in Hilo Bay in Hawaii. Since relatively more field data on tsunami inundation are available for Hilo Bay, this case study can help to evaluate the applicability of the methodology for predicting tsunami inundation risk in the Pacific Basin. Detailed results will be presented at the AGU meeting.

Automated inundation monitoring using TerraSAR-X multitemporal imagery

NASA Astrophysics Data System (ADS)

Gebhardt, S.; Huth, J.; Wehrmann, T.; Schettler, I.; Künzer, C.; Schmidt, M.; Dech, S.

2009-04-01

The Mekong Delta in Vietnam offers natural resources for several million inhabitants. However, a strong population increase, changing climatic conditions and regulatory measures at the upper reaches of the Mekong lead to severe changes in the Delta. Extreme flood events occur more frequently, drinking water availability is increasingly limited, soils show signs of salinization or acidification, species and complete habitats diminish. During the Monsoon season the river regularly overflows its banks in the lower Mekong area, usually with beneficial effects. However, extreme flood events occur more frequently causing extensive damage, on the average once every 6 to 10 years river flood levels exceed the critical beneficial level X-band SAR data are well suited for deriving inundated surface areas. The TerraSAR-X sensor with its different scanning modi allows for the derivation of spatial and temporal high resolved inundation masks. The paper presents an automated procedure for deriving inundated areas from TerraSAR-X Scansar and Stripmap image data. Within the framework of the German-Vietnamese WISDOM project, focussing the Mekong Delta region in Vietnam, images have been acquired covering the flood season from June 2008 to November 2008. Based on these images a time series of the so called watermask showing inundated areas have been derived. The product is required as intermediate to (i) calibrate 2d inundation model scenarios, (ii) estimate the extent of affected areas, and (iii) analyze the scope of prior crisis. The image processing approach is based on the assumption that water surfaces are forward scattering the radar signal resulting in low backscatter signals to the sensor. It uses multiple grey level thresholds and image morphological operations. The approach is robust in terms of automation, accuracy, robustness, and processing time. The resulting watermasks show the seasonal flooding pattern with inundations starting in July, having their peak at the end of September, and lower down until December in 2008. The results are a valuable input for monitoring and understanding the seasonal regional flood patterns for calibrating 2d inundation models, as also for generating value added products in combination with agricultural land use and socio-economic data for further separation of inundated and irrigated areas.

Detection of Flood Inundation Information of the Kinu River Flooding in 2015 by Social Media

NASA Astrophysics Data System (ADS)

Shi, Y.; Sayama, T.; Takara, K. T.

2016-12-01

On September 10th, 2015, due to Kanto Tohoku heavy rainfall in Japan, an overtopping occurred from the Kinu River around 6:00. At the same day, levee breach occurred at the downstream area near Joso city in Ibaraki Prefecture, Japan. This flood disaster caused two people dead, several people injured, and enormous damages on houses and infrastructures in the city. In order to mitigate such flood disasters with large inundations, it is important to identify flood-affected areas on real-time basis. The real-time flood hazard map, which is our ultimate goal of the study, provides information on location of inundated areas during a flood. However, the technology has not been achieved yet mainly due to the difficulty in identifying the flood extent on real time. With the advantage of efficiency and wide coverage, social media, such as Twitter, appears as a good data source for collecting real-time flood information. However, there are some concerns on social media information, including the trustworthiness, and the amount of useful information in the case tweets from flood affected areas. This study collected tweet regarding the Kinu River flooding and investigated how many people in affected area posted tweets on the flooding and how the detected information is useful for the eventual goal on the real-time flood hazard mapping. The tweets were collected by three ways: advanced search on twitter web page; DISAster-information ANAlyzer system; and Twitter Application Programming Interfaces. As a result, 109 disaster relevant tweets were collected. Out of the 109 tweets, 32% of the total tweets are posted at real-time, 43% of total tweets are posted with photos and 46 tweets are related to the inundation information. 46% of the inundation related tweets were able to identify locations. In order to investigate the reliability of tweet post, the location identified tweets were marked on map to compare with the real inundation extent that measured by the Geospatial Information Authority of Japan (GSI) by helicopter on September 10, 2015. The result shows a good agreement between the actual inundation information and tweet post. Moreover, the tweet posts show an appropriate change of inundation extent. In addition, tweet posts show some additional inundated areas not reported by GSI, but confirmed the inundation after the disaster.

Ground Truthing Hurricane Nate to Validate Bathtub Models of Inundation of Coastal Harrison County, MS.

NASA Astrophysics Data System (ADS)

Thibault, C. H.

2017-12-01

Simple bathtub inundation models were developed using a digital elevation model of coastal Harrison County, MS to determine the extent of flooding for a variety of storm surge scenarios including estimated storm surges associated with Hurricane Nate, the fourth Atlantic Hurricane to make landfall on a United States coastline in 2017. High water mark data were collected immediately following the Hurricane Nate landfall near Biloxi in Harrison County, MS and were used to validate the low lying inundation contours. The models were then used to quantify the total area of land inundation between one-meter contours. The models show a bimodal pattern of inundation with the greatest amount of inundation occurring between the lower lying 1m-2m and 2m-3m contours characterized by low gradient wetlands, beaches, and roads and the higher positioned 6m-7m and 7m-8m contours characterized by developed areas.

The Use of LIDAR and Volunteered Geographic Information to Map Flood Extents and Inundation

NASA Astrophysics Data System (ADS)

McDougall, K.; Temple-Watts, P.

2012-07-01

Floods are one of the most destructive natural disasters that threaten communities and properties. In recent decades, flooding has claimed more lives, destroyed more houses and ruined more agricultural land than any other natural hazard. The accurate prediction of the areas of inundation from flooding is critical to saving lives and property, but relies heavily on accurate digital elevation and hydrologic models. The 2011 Brisbane floods provided a unique opportunity to capture high resolution digital aerial imagery as the floods neared their peak, allowing the capture of areas of inundation over the various city suburbs. This high quality imagery, together with accurate LiDAR data over the area and publically available volunteered geographic imagery through repositories such as Flickr, enabled the reconstruction of flood extents and the assessment of both area and depth of inundation for the assessment of damage. In this study, approximately 20 images of flood damaged properties were utilised to identify the peak of the flood. Accurate position and height values were determined through the use of RTK GPS and conventional survey methods. This information was then utilised in conjunction with river gauge information to generate a digital flood surface. The LiDAR generated DEM was then intersected with the flood surface to reconstruct the area of inundation. The model determined areas of inundation were then compared to the mapped flood extent from the high resolution digital imagery to assess the accuracy of the process. The paper concludes that accurate flood extent prediction or mapping is possible through this method, although its accuracy is dependent on the number and location of sampled points. The utilisation of LiDAR generated DEMs and DSMs can also provide an excellent mechanism to estimate depths of inundation and hence flood damage

Projections of tsunami inundation area coupled with impacts of sea level rise in Banda Aceh, Indonesia

NASA Astrophysics Data System (ADS)

Tursina, Syamsidik, Kato, Shigeru

2017-10-01

In a long term, sea level rise is anticipated to give devastating effects on Banda Aceh, as one of the coastal cities in the northern tip of Sumatra. The growth of the population and buildings in the city has come to the stage where the coastal area is vulnerable to any coastal hazard. Some public facilities and settlements have been constructed and keep expanding in the future. According to TOPEX/POSEIDON satellite images, 7 mm/year the sea level has been risen between 1992 and 2015 in this area. It is estimated that in the next 100 years, there will be 700 mm additional sea level rise which will give a setback more over to a rather flat area around the coast. This research is aim at investigating the influence of sea level rise toward the tsunami inundation on the land area particularly the impacts on Banda Aceh city. Cornell Multigrid Coupled Tsunami Model (COMCOT) simulation numerically generated tsunami propagation. Topography and bathymetry data were collected from GEBCO and updated with the available nautical chart (DISHIDROS, JICA, and field measurements). Geological movement of the underwater fault was generated using Piatanesi and Lorito of 9.15 Mw 2004 multi-fault scenario. The inundation area produced by COMCOT revealed that the inundation area was expanded to several hundred meters from the shoreline. To investigate the impacts of tsunami wave on Banda Aceh, the inundation area were digitized and analyzed with Quantum GIS spatial tools. The Quantum GIS analyzed inundations area affected by the projected tsunami. It will give a new tsunami-prone coastal area map induced by sea level rise in 100 years.

Flood-Inundation Maps of Selected Areas Affected by the Flood of October 2015 in Central and Coastal South Carolina

USGS Publications Warehouse

Musser, Jonathan W.; Watson, Kara M.; Painter, Jaime A.; Gotvald, Anthony J.

2016-02-22

Heavy rainfall occurred across South Carolina during October 1–5, 2015, as a result of an upper atmospheric low-pressure system that funneled tropical moisture from Hurricane Joaquin into the State. The storm caused major flooding in the central and coastal parts of South Carolina. Almost 27 inches of rain fell near Mount Pleasant in Charleston County during this period. U.S. Geological Survey (USGS) streamgages recorded peaks of record at 17 locations, and 15 other locations had peaks that ranked in the top 5 for the period of record. During the October 2015 flood event, USGS personnel made about 140 streamflow measurements at 86 locations to verify, update, or extend existing rating curves (which are used to compute streamflow from monitored river stage). Immediately after the storm event, USGS personnel documented 602 high-water marks, noting the location and height of the water above land surface. Later in October, 50 additional high-water marks were documented near bridges for South Carolina Department of Transportation. Using a subset of these high-water marks, 20 flood-inundation maps of 12 communities were created. Digital datasets of the inundation area, modeling boundary, and water depth rasters are all available for download.

The Development of High-speed Full-function Storm Surge Model and the Case Study of 2013 Typhoon Haiyan

NASA Astrophysics Data System (ADS)

Tsai, Y. L.; Wu, T. R.; Lin, C. Y.; Chuang, M. H.; Lin, C. W.

2016-02-01

An ideal storm surge operational model should feature as: 1. Large computational domain which covers the complete typhoon life cycle. 2. Supporting both parametric and atmospheric models. 3. Capable of calculating inundation area for risk assessment. 4. Tides are included for accurate inundation simulation. Literature review shows that not many operational models reach the goals for the fast calculation, and most of the models have limited functions. In this paper, a well-developed COMCOT (COrnell Multi-grid Coupled of Tsunami Model) tsunami model is chosen as the kernel to establish a storm surge model which solves the nonlinear shallow water equations on both spherical and Cartesian coordinates directly. The complete evolution of storm surge including large-scale propagation and small-scale offshore run-up can be simulated by nested-grid scheme. The global tide model TPXO 7.2 established by Oregon State University is coupled to provide astronomical boundary conditions. The atmospheric model named WRF (Weather Research and Forecasting Model) is also coupled to provide metrological fields. The high-efficiency thin-film method is adopted to evaluate the storm surge inundation. Our in-house model has been optimized by OpenMp (Open Multi-Processing) with the performance which is 10 times faster than the original version and makes it an early-warning storm surge model. In this study, the thorough simulation of 2013 Typhoon Haiyan is performed. The detailed results will be presented in Oceanic Science Meeting of 2016 in terms of surge propagation and high-resolution inundation areas.

Source of the 1730 Chilean earthquake from historical records: Implications for the future tsunami hazard on the coast of Metropolitan Chile

NASA Astrophysics Data System (ADS)

Carvajal, M.; Cisternas, M.; Catalán, P. A.

2017-05-01

Historical records of an earthquake that occurred in 1730 affecting Metropolitan Chile provide essential clues on the source characteristics for the future earthquakes in the region. The earthquake and tsunami of 1730 have been recognized as the largest to occur in Metropolitan Chile since the beginning of written history. The earthquake destroyed buildings along >1000 km of the coast and produced a large tsunami that caused damage as far as Japan. Here its source characteristics are inferred by comparing local tsunami inundations computed from hypothetical earthquakes with varying magnitude and depth, with those inferred from historical observations. It is found that a 600-800 km long rupture involving average slip amounts of 10-14 m (Mw 9.1-9.3) best explains the observed tsunami heights and inundations. This large earthquake magnitude is supported by the 1730 tsunami heights inferred in Japan. The inundation results combined with local uplift reports suggest a southward increase of the slip depth along the rupture zone of the 1730 earthquake. While shallow slip on the area to the north of the 2010 earthquake rupture zone is required to explain the reported inundation, only deeper slip at this area can explain the coastal uplift reports. Since the later earthquakes of the region involved little or no slip at shallow depths, the near-future earthquakes on Metropolitan Chile could release the shallow slip accumulated since 1730 and thus lead to strong tsunami excitation. Moderate shaking from a shallow earthquake could delay tsunami evacuation for the most populated coastal region of Chile.

Airborne Imaging in the Yukon River Basin to Characterize SWOT Mission Phenomenology

NASA Astrophysics Data System (ADS)

Moller, D.; Pavelsky, T.; Arvesen, J. C.

2015-12-01

Remote sensing offers intriguing tools to track Arctic hydrology, but current techniques are largely limited to tracking either inundation or water surface elevation only. For the first time, the proposed Surface Water Ocean Topography (SWOT) satellite mission will provide regular, simultaneous observations of inundation extent and water level from space. SWOT is unique and distinct from precursor altimetry missions in some notable regards: 1) 100km+ of swath will provide complete ocean coverage, 2) in addition to the ocean product, land surface water will be mapped for storage measurement and discharge estimation and 3) Ka-band single-pass interferometry will produce the height measurements introducing a new measurement technique. This new approach introduces additional algorithmic, characterization and calibration/validation needs for which the Ka-band SWOT Phenomenology Airborne Radar (KaSPAR) was developed. In May 2015, AirSWOT (comprised of KaSPAR and a color infrared (CIR) high resolution aerial camera) was part of an intensive field campaign including observations of inundation extent and water level and in situ hydrologic measurements in two rivers and 20 lakes within the Yukon River Basin, Alaska. One goal is to explore the fundamental phenomenology of the SWOT measurement. This includes assessment of the effects of vegetation layover and attenuation, wind roughening and classification. Further KaSPAR-derived inundation extent will to be validated using a combination of ground surveys and coregistered CIR imagery. Ultimately, by combining measurements of changing inundation extent and water level between two collection dates, it will be possible to validate lake water storage variations against storage changes computed from in situ water levels and inundation area derived from AirSWOT. Our paper summarizes the campaign, the airborne and in situ measurements and presents some initial KaSPAR and CIR imagery from the Yukon flats region.

Estimation of human damage and economic loss of buildings for the worst-credible scenario of tsunami inundation in the city of Augusta, Italy

NASA Astrophysics Data System (ADS)

Pagnoni, Gianluca; Tinti, Stefano

2017-04-01

The city of Augusta is located in the southern part of the eastern coast of Sicily. Italian tsunami catalogue and paleo-tsunami surveys indicate that at least 7 events of tsunami affected the bay of Augusta in the last 4,000 years, two of which are associated with earthquakes (1169 and 1693) that destroyed the city. For these reasons Augusta has been chosen in the project ASTARTE as a test site for the study of issues related to tsunami hazard and risk. In last two years we studied hazard through the approach of the worst-case credible scenario and carried out vulnerability and damage analysis for buildings. In this work, we integrate that research, and estimate the damage to people and the economic loss of buildings due to structural damage. As regards inundation, we assume both uniform inundation levels (bath-tub hypothesis) and inundation data resulting from the worst-case scenario elaborated for the area by Armigliato et al. (2015). Human damage is calculated in three steps using the method introduced by Pagnoni et al. (2016) following the work by Terrier et al. (2012) and by Koshimura et al. (2009). First, we use census data to estimate the number of people present in each residential building affected by inundation; second, based on water column depth and building type, we evaluate the level of damage to people; third, we provide an estimate of fatalities. The economic loss is computed for two types of buildings (residential and trade-industrial) by using data on inundation and data from the real estate market. This study was funded by the EU Project ASTARTE - "Assessment, STrategy And Risk Reduction for Tsunamis in Europe", Grant 603839, 7th FP (ENV.2013.6.4-3)

A numerical study on hurricane-induced storm surge and inundation in Charleston Harbor, South Carolina

NASA Astrophysics Data System (ADS)

Peng, Machuan; Xie, Lian; Pietrafesa, Leonard J.

2006-08-01

A storm surge and inundation model is configured in Charleston Harbor and its adjacent coastal region to study the harbor's response to hurricanes. The hydrodynamic component of the modeling system is based on the Princeton Ocean Model, and a scheme with multiple inundation speed options is imbedded in the model for the inundation calculation. Historic observations (Hurricane Hugo and its related storm surge and inundation) in the Charleston Harbor region indicate that among three possible inundation speeds in the model, taking Ct (gd)1/2 (Ct is a terrain-related parameter) as the inundation speed is the best choice. Choosing a different inundation speed in the model has effects not only on inundation area but also on storm surge height. A nesting technique is necessary for the model system to capture the mesoscale feature of a hurricane and meanwhile to maintain a higher horizontal resolution in the harbor region, where details of the storm surge and inundation are required. Hurricane-induced storm surge and inundation are very sensitive to storm tracks. Twelve hurricanes with different tracks are simulated to investigate how Charleston Harbor might respond to tracks that are parallel or perpendicular to the coastline or landfall at Charleston at different angles. Experiments show that large differences of storm surge and inundation may have occurred if Hurricane Hugo had approached Charleston Harbor with a slightly different angle. A hurricane's central pressure, radius of maximum wind, and translation speed have their own complicated effects on surge and inundation when the hurricane approaches the coast on different tracks. Systematic experiments are performed in order to illustrate how each of such factors, or a combination of them, may affect the storm surge height and inundation area in the Charleston Harbor region. Finally, suggestions are given on how this numerical model system may be used for hurricane-induced storm surge and inundation forecasting.

A method to estimate expected fatalities and economic loss of buildings in an urban environment as a step toward tsunami risk assessment: an application to the city of Siracusa, Italy.

NASA Astrophysics Data System (ADS)

Pagnoni, Gianluca; Accorsi, Eleonora; Tinti, Stefano

2016-04-01

Siracusa, an important city of the south-east Sicily, is located in an area highly exposed to the danger of tsunami, local and remote. Among the many events that affected this area those with a major effect are the AD 365 tsunami generated by an earthquake in the Western Hellenic Arc, the event of 11 January 1693, following an earthquake in the area of Augusta, and the tsunami of 28 December 1908 generated in the Messina strait. The aim of this study is to evaluate the number of exposed people and of fatalities as well as the type of damage to constructions and the associated loss of economic value in case of a tsunami, based on a simple tsunami scenario, i.e. on assuming a uniform inundation level of 5 m. This figure is considered appropriate for this preliminary tsunami loss analysis since it is compatible with historical tsunami observations and is also supported by recent tsunami hazard studies carried out for this area (Armigliato et al., 2015). The main physical tsunami parameter used in computations is the water column, which is merely the difference between the assumed inundation level and the topographic altitude. We use numerical geo-referenced 1:2000 maps providing a database of constructions in the area of Siracusa together with data from national and local statistical institutions to make estimates on the number and type of buildings and on the number of people that may be found in the inundation area in different periods of the year, discriminating between residents and tourists. Using a variant of the Terrier et al. (2012) table and tsunami mortality curves proposed by Koshimura et al. (2009) we are able to estimate expected fatalities with tsunami inundation reaching at most the first floor of buildings. We calculate economic loss by taking into account both residential buildings and commercial-industrial structures and data from the real estate market. This study is funded by the EU Project ASTARTE - "Assessment, STrategy And Risk Reduction for Tsunamis in Europe", Grant 603839, 7th FP (ENV.2013.6.4-3)

Flood-inundation maps for the White River at Newberry, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.; Kim, Moon H.; Menke, Chad D.

2012-01-01

Digital flood-inundation maps for a 4.9-mile reach of the White River at Newberry, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at USGS streamgage 03360500, White River at Newberry, Ind. Current conditions at the USGS streamgage may be obtained on the Internet (http://waterdata.usgs.gov/in/nwis/uv?site_no=03360500). The National Weather Service (NWS) forecasts flood hydrographs at the Newberry streamgage. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the White River reach by means of a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current stage-discharge relation at USGS streamgage 03360500, White River at Newberry, Ind., and high-water marks from a flood in June 2008.The calibrated hydraulic model was then used to determine 22 water-surface profiles for flood stages a1-foot intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage at Newberry, Ind., and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post-flood recovery efforts.

Developing flood-inundation maps for Johnson Creek, Portland, Oregon

USGS Publications Warehouse

Stonewall, Adam J.; Beal, Benjamin A.

2017-04-14

Digital flood-inundation maps were created for a 12.9‑mile reach of Johnson Creek by the U.S. Geological Survey (USGS). The flood-inundation maps depict estimates of water depth and areal extent of flooding from the mouth of Johnson Creek to just upstream of Southeast 174th Avenue in Portland, Oregon. Each flood-inundation map is based on a specific water level and associated streamflow at the USGS streamgage, Johnson Creek at Sycamore, Oregon (14211500), which is located near the upstream boundary of the maps. The maps produced by the USGS, and the forecasted flood hydrographs produced by National Weather Service River Forecast Center can be accessed through the USGS Flood Inundation Mapper Web site (http://wimcloud.usgs.gov/apps/FIM/FloodInundationMapper.html).Water-surface elevations were computed for Johnson Creek using a combined one-dimensional and two‑dimensional unsteady hydraulic flow model. The model was calibrated using data collected from the flood of December 2015 (including the calculated streamflows at two USGS streamgages on Johnson Creek) and validated with data from the flood of January 2009. Results were typically within 0.6 foot (ft) of recorded or measured water-surface elevations from the December 2015 flood, and within 0.8 ft from the January 2009 flood. Output from the hydraulic model was used to create eight flood inundation maps ranging in stage from 9 to 16 ft. Boundary condition hydrographs were identical in shape to those from the December 2015 flood event, but were scaled up or down to produce the amount of streamflow corresponding to a specific water-surface elevation at the Sycamore streamgage (14211500). Sensitivity analyses using other hydrograph shapes, and a version of the model in which the peak flow is maintained for an extended period of time, showed minimal variation, except for overbank areas near the Foster Floodplain Natural Area.Simulated water-surface profiles were combined with light detection and ranging (lidar) data collected in 2014 to delineate water-surface extents for each of the eight modeled stages. The availability of flood-inundation maps in conjunction with real-time data from the USGS streamgages along Johnson Creek and forecasted hydrographs from the National Weather Service Northwest River Forecast Center will provide residents of the watershed and emergency management personnel with valuable information that may aid in flood response, including potential evacuations, road closures, and mitigation efforts. In addition, these maps may be used for post-flood recovery efforts.

Parallel simulation of tsunami inundation on a large-scale supercomputer

NASA Astrophysics Data System (ADS)

Oishi, Y.; Imamura, F.; Sugawara, D.

2013-12-01

An accurate prediction of tsunami inundation is important for disaster mitigation purposes. One approach is to approximate the tsunami wave source through an instant inversion analysis using real-time observation data (e.g., Tsushima et al., 2009) and then use the resulting wave source data in an instant tsunami inundation simulation. However, a bottleneck of this approach is the large computational cost of the non-linear inundation simulation and the computational power of recent massively parallel supercomputers is helpful to enable faster than real-time execution of a tsunami inundation simulation. Parallel computers have become approximately 1000 times faster in 10 years (www.top500.org), and so it is expected that very fast parallel computers will be more and more prevalent in the near future. Therefore, it is important to investigate how to efficiently conduct a tsunami simulation on parallel computers. In this study, we are targeting very fast tsunami inundation simulations on the K computer, currently the fastest Japanese supercomputer, which has a theoretical peak performance of 11.2 PFLOPS. One computing node of the K computer consists of 1 CPU with 8 cores that share memory, and the nodes are connected through a high-performance torus-mesh network. The K computer is designed for distributed-memory parallel computation, so we have developed a parallel tsunami model. Our model is based on TUNAMI-N2 model of Tohoku University, which is based on a leap-frog finite difference method. A grid nesting scheme is employed to apply high-resolution grids only at the coastal regions. To balance the computation load of each CPU in the parallelization, CPUs are first allocated to each nested layer in proportion to the number of grid points of the nested layer. Using CPUs allocated to each layer, 1-D domain decomposition is performed on each layer. In the parallel computation, three types of communication are necessary: (1) communication to adjacent neighbours for the finite difference calculation, (2) communication between adjacent layers for the calculations to connect each layer, and (3) global communication to obtain the time step which satisfies the CFL condition in the whole domain. A preliminary test on the K computer showed the parallel efficiency on 1024 cores was 57% relative to 64 cores. We estimate that the parallel efficiency will be considerably improved by applying a 2-D domain decomposition instead of the present 1-D domain decomposition in future work. The present parallel tsunami model was applied to the 2011 Great Tohoku tsunami. The coarsest resolution layer covers a 758 km × 1155 km region with a 405 m grid spacing. A nesting of five layers was used with the resolution ratio of 1/3 between nested layers. The finest resolution region has 5 m resolution and covers most of the coastal region of Sendai city. To complete 2 hours of simulation time, the serial (non-parallel) computation took approximately 4 days on a workstation. To complete the same simulation on 1024 cores of the K computer, it took 45 minutes which is more than two times faster than real-time. This presentation discusses the updated parallel computational performance and the efficient use of the K computer when considering the characteristics of the tsunami inundation simulation model in relation to the characteristics and capabilities of the K computer.

Tsunami simulation method initiated from waveforms observed by ocean bottom pressure sensors for real-time tsunami forecast; Applied for 2011 Tohoku Tsunami

NASA Astrophysics Data System (ADS)

Tanioka, Yuichiro

2017-04-01

After tsunami disaster due to the 2011 Tohoku-oki great earthquake, improvement of the tsunami forecast has been an urgent issue in Japan. National Institute of Disaster Prevention is installing a cable network system of earthquake and tsunami observation (S-NET) at the ocean bottom along the Japan and Kurile trench. This cable system includes 125 pressure sensors (tsunami meters) which are separated by 30 km. Along the Nankai trough, JAMSTEC already installed and operated the cable network system of seismometers and pressure sensors (DONET and DONET2). Those systems are the most dense observation network systems on top of source areas of great underthrust earthquakes in the world. Real-time tsunami forecast has depended on estimation of earthquake parameters, such as epicenter, depth, and magnitude of earthquakes. Recently, tsunami forecast method has been developed using the estimation of tsunami source from tsunami waveforms observed at the ocean bottom pressure sensors. However, when we have many pressure sensors separated by 30km on top of the source area, we do not need to estimate the tsunami source or earthquake source to compute tsunami. Instead, we can initiate a tsunami simulation from those dense tsunami observed data. Observed tsunami height differences with a time interval at the ocean bottom pressure sensors separated by 30 km were used to estimate tsunami height distribution at a particular time. In our new method, tsunami numerical simulation was initiated from those estimated tsunami height distribution. In this paper, the above method is improved and applied for the tsunami generated by the 2011 Tohoku-oki great earthquake. Tsunami source model of the 2011 Tohoku-oki great earthquake estimated using observed tsunami waveforms, coseimic deformation observed by GPS and ocean bottom sensors by Gusman et al. (2012) is used in this study. The ocean surface deformation is computed from the source model and used as an initial condition of tsunami simulation. By assuming that this computed tsunami is a real tsunami and observed at ocean bottom sensors, new tsunami simulation is carried out using the above method. The station distribution (each station is separated by 15 min., about 30 km) observed tsunami waveforms which were actually computed from the source model. Tsunami height distributions are estimated from the above method at 40, 80, and 120 seconds after the origin time of the earthquake. The Near-field Tsunami Inundation forecast method (Gusman et al. 2014) was used to estimate the tsunami inundation along the Sanriku coast. The result shows that the observed tsunami inundation was well explained by those estimated inundation. This also shows that it takes about 10 minutes to estimate the tsunami inundation from the origin time of the earthquake. This new method developed in this paper is very effective for a real-time tsunami forecast.

A software tool for rapid flood inundation mapping

USGS Publications Warehouse

Verdin, James; Verdin, Kristine; Mathis, Melissa L.; Magadzire, Tamuka; Kabuchanga, Eric; Woodbury, Mark; Gadain, Hussein

2016-06-02

The GIS Flood Tool (GFT) was developed by the U.S. Geological Survey with support from the U.S. Agency for International Development’s Office of U.S. Foreign Disaster Assistance to provide a means for production of reconnaissance-level flood inundation mapping for data-sparse and resource-limited areas of the world. The GFT has also attracted interest as a tool for rapid assessment flood inundation mapping for the Flood Inundation Mapping Program of the U.S. Geological Survey. The GFT can fill an important gap for communities that lack flood inundation mapping by providing a first-estimate of inundation zones, pending availability of resources to complete an engineering study. The tool can also help identify priority areas for application of scarce flood inundation mapping resources. The technical basis of the GFT is an application of the Manning equation for steady flow in an open channel, operating on specially processed digital elevation data. The GFT is implemented as a software extension in ArcGIS. Output maps from the GFT were validated at 11 sites with inundation maps produced previously by the Flood Inundation Mapping Program using standard one-dimensional hydraulic modeling techniques. In 80 percent of the cases, the GFT inundation patterns matched 75 percent or more of the one-dimensional hydraulic model inundation patterns. Lower rates of pattern agreement were seen at sites with low relief and subtle surface water divides. Although the GFT is simple to use, it should be applied with the oversight or review of a qualified hydraulic engineer who understands the simplifying assumptions of the approach.

Evaluation of low impact development approach for mitigating flood inundation at a watershed scale in China.

PubMed

Hu, Maochuan; Sayama, Takahiro; Zhang, Xingqi; Tanaka, Kenji; Takara, Kaoru; Yang, Hong

2017-05-15

Low impact development (LID) has attracted growing attention as an important approach for urban flood mitigation. Most studies evaluating LID performance for mitigating floods focus on the changes of peak flow and runoff volume. This paper assessed the performance of LID practices for mitigating flood inundation hazards as retrofitting technologies in an urbanized watershed in Nanjing, China. The findings indicate that LID practices are effective for flood inundation mitigation at the watershed scale, and especially for reducing inundated areas with a high flood hazard risk. Various scenarios of LID implementation levels can reduce total inundated areas by 2%-17% and areas with a high flood hazard level by 6%-80%. Permeable pavement shows better performance than rainwater harvesting against mitigating urban waterlogging. The most efficient scenario is combined rainwater harvesting on rooftops with a cistern capacity of 78.5 mm and permeable pavement installed on 75% of non-busy roads and other impervious surfaces. Inundation modeling is an effective approach to obtaining the information necessary to guide decision-making for designing LID practices at watershed scales. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hurricane Matthew (2016) and its Storm Surge Inundation under Global Warming Scenarios: Application of an Interactively Coupled Atmosphere-Ocean Model

NASA Astrophysics Data System (ADS)

Jisan, M. A.; Bao, S.; Pietrafesa, L.; Pullen, J.

2017-12-01

An interactively coupled atmosphere-ocean model was used to investigate the impacts of future ocean warming, both at the surface and the layers below, on the track and intensity of a hurricane and its associated storm surge and inundation. The category-5 hurricane Matthew (2016), which made landfall on the South Carolina coast of the United States, was used for the case study. Future ocean temperature changes and sea level rise (SLR) were estimated based on the projection of Inter-Governmental Panel on Climate Change (IPCC)'s Representative Concentration Pathway scenarios RCP 2.6 and RCP 8.5. After being validated with the present-day observational data, the model was applied to simulate the changes in track, intensity, storm surge and inundation that Hurricane Matthew would cause under future climate change scenarios. It was found that a significant increase in hurricane intensity, storm surge water level, and inundation area for Hurricane Matthew under future ocean warming and SLR scenarios. For example, under the RCP 8.5 scenario, the maximum wind speed would increase by 17 knots (14.2%), the minimum sea level pressure would decrease by 26 hPa (2.85%), and the inundated area would increase by 401 km2 (123%). By including the effect of SLR for the middle-21st-century scenario, the inundated area will further increase by up to 49.6%. The increase in the hurricane intensity and the inundated area was also found for the RCP 2.6 scenario. The response of sea surface temperature was analyzed to investigate the change in intensity. A comparison was made between the impacts when only the sea surface warming is considered versus when both the sea surface and the underneath layers are considered. These results showed that even without the effect of SLR, the storm surge level and the inundated area would be higher due to the increased hurricane intensity under the influence of the future warmer ocean temperature. The coupled effect of ocean warming and SLR would cause the hurricane-induced storm surge and inundation to be amplified. The relative importance of the ocean warming versus the SLR was evaluated. Keywords: Hurricane Matthew, Global Warming, Coupled Atmosphere-Ocean Model, Air-Sea interactions, Storm Surge, Inundation

Hurricane Harvey Riverine Flooding: Part 1 - Reconstruction of Hurricane Harvey Flooding for Harris County, TX using a GPU-accelerated 2D flood model for post-flood hazard analysis

NASA Astrophysics Data System (ADS)

Kalyanapu, A. J.; Dullo, T. T.; Gangrade, S.; Kao, S. C.; Marshall, R.; Islam, S. R.; Ghafoor, S. K.

2017-12-01

Hurricane Harvey that made landfall in the southern Texas this August is one of the most destructive hurricanes during the 2017 hurricane season. During its active period, many areas in coastal Texas region received more than 40 inches of rain. This downpour caused significant flooding resulting in about 77 casualties, displacing more than 30,000 people, inundating hundreds of thousands homes and is currently estimated to have caused more than $70 billion in direct damage. One of the significantly affected areas is Harris County where the city of Houston, TX is located. Covering over two HUC-8 drainage basins ( 2702 mi2), this county experienced more than 80% of its annual average rainfall during this event. This study presents an effort to reconstruct flooding caused by extreme rainfall due to Hurricane Harvey in Harris County, Texas. This computationally intensive task was performed at a 30-m spatial resolution using a rapid flood model called Flood2D-GPU, a graphics processing unit (GPU) accelerated model, on Oak Ridge National Laboratory's (ORNL) Titan Supercomputer. For this task, the hourly rainfall estimates from the National Center for Environmental Prediction Stage IV Quantitative Precipitation Estimate were fed into the Variable Infiltration Capacity (VIC) hydrologic model and Routing Application for Parallel computation of Discharge (RAPID) routing model to estimate flow hydrographs at 69 locations for Flood2D-GPU simulation. Preliminary results of the simulation including flood inundation extents, maps of flood depths and inundation duration will be presented. Future efforts will focus on calibrating and validating the simulation results and assessing the flood damage for better understanding the impacts made by Hurricane Harvey.

Sub-pixel flood inundation mapping from multispectral remotely sensed images based on discrete particle swarm optimization

NASA Astrophysics Data System (ADS)

Li, Linyi; Chen, Yun; Yu, Xin; Liu, Rui; Huang, Chang

2015-03-01

The study of flood inundation is significant to human life and social economy. Remote sensing technology has provided an effective way to study the spatial and temporal characteristics of inundation. Remotely sensed images with high temporal resolutions are widely used in mapping inundation. However, mixed pixels do exist due to their relatively low spatial resolutions. One of the most popular approaches to resolve this issue is sub-pixel mapping. In this paper, a novel discrete particle swarm optimization (DPSO) based sub-pixel flood inundation mapping (DPSO-SFIM) method is proposed to achieve an improved accuracy in mapping inundation at a sub-pixel scale. The evaluation criterion for sub-pixel inundation mapping is formulated. The DPSO-SFIM algorithm is developed, including particle discrete encoding, fitness function designing and swarm search strategy. The accuracy of DPSO-SFIM in mapping inundation at a sub-pixel scale was evaluated using Landsat ETM + images from study areas in Australia and China. The results show that DPSO-SFIM consistently outperformed the four traditional SFIM methods in these study areas. A sensitivity analysis of DPSO-SFIM was also carried out to evaluate its performances. It is hoped that the results of this study will enhance the application of medium-low spatial resolution images in inundation detection and mapping, and thereby support the ecological and environmental studies of river basins.

Evaluation of Dynamic Coastal Response to Sea-level Rise Modifies Inundation Likelihood

NASA Technical Reports Server (NTRS)

Lentz, Erika E.; Thieler, E. Robert; Plant, Nathaniel G.; Stippa, Sawyer R.; Horton, Radley M.; Gesch, Dean B.

2016-01-01

Sea-level rise (SLR) poses a range of threats to natural and built environments, making assessments of SLR-induced hazards essential for informed decision making. We develop a probabilistic model that evaluates the likelihood that an area will inundate (flood) or dynamically respond (adapt) to SLR. The broad-area applicability of the approach is demonstrated by producing 30x30m resolution predictions for more than 38,000 sq km of diverse coastal landscape in the northeastern United States. Probabilistic SLR projections, coastal elevation and vertical land movement are used to estimate likely future inundation levels. Then, conditioned on future inundation levels and the current land-cover type, we evaluate the likelihood of dynamic response versus inundation. We find that nearly 70% of this coastal landscape has some capacity to respond dynamically to SLR, and we show that inundation models over-predict land likely to submerge. This approach is well suited to guiding coastal resource management decisions that weigh future SLR impacts and uncertainty against ecological targets and economic constraints.

Flood inundation map library, Fort Kent, Maine

USGS Publications Warehouse

Lombard, Pamela J.

2012-01-01

Severe flooding occurred in northern Maine from April 28 to May 1, 2008, and damage was extensive in the town of Fort Kent (Lombard, 2010). Aroostook County was declared a Federal disaster area on May 9, 2008. The extent of flooding on both the Fish and St. John Rivers during this event showed that the current Federal Emergency Management Agency (FEMA) Flood Insurance Study (FIS) and Flood Insurance Rate Map (FIRM) (Federal Emergency Management Agency, 1979) were out of date. The U.S. Geological Survey (USGS) conducted a study to develop a flood inundation map library showing the areas and depths for a range of flood stages from bankfull to the flood of record for Fort Kent to complement an updated FIS (Federal Emergency Management Agency, in press). Hydrologic analyses that support the maps include computer models with and without the levee and with various depths of backwater on the Fish River. This fact sheet describes the methods used to develop the maps and describes how the maps can be accessed.

Global climate change and local land subsidence exacerbate inundation risk to the San Francisco Bay Area

PubMed Central

Shirzaei, Manoochehr; Bürgmann, Roland

2018-01-01

The current global projections of future sea level rise are the basis for developing inundation hazard maps. However, contributions from spatially variable coastal subsidence have generally not been considered in these projections. We use synthetic aperture radar interferometric measurements and global navigation satellite system data to show subsidence rates of less than 2 mm/year along most of the coastal areas along San Francisco Bay. However, rates exceed 10 mm/year in some areas underlain by compacting artificial landfill and Holocene mud deposits. The maps estimating 100-year inundation hazards solely based on the projection of sea level rise from various emission scenarios underestimate the area at risk of flooding by 3.7 to 90.9%, compared with revised maps that account for the contribution of local land subsidence. Given ongoing land subsidence, we project that an area of 125 to 429 km2 will be vulnerable to inundation, as opposed to 51 to 413 km2 considering sea level rise alone. PMID:29536042

An evaluation of onshore digital elevation models for tsunami inundation modelling

NASA Astrophysics Data System (ADS)

Griffin, J.; Latief, H.; Kongko, W.; Harig, S.; Horspool, N.; Hanung, R.; Rojali, A.; Maher, N.; Fountain, L.; Fuchs, A.; Hossen, J.; Upi, S.; Dewanto, S. E.; Cummins, P. R.

2012-12-01

Tsunami inundation models provide fundamental information about coastal areas that may be inundated in the event of a tsunami along with additional parameters such as flow depth and velocity. This can inform disaster management activities including evacuation planning, impact and risk assessment and coastal engineering. A fundamental input to tsunami inundation models is adigital elevation model (DEM). Onshore DEMs vary widely in resolution, accuracy, availability and cost. A proper assessment of how the accuracy and resolution of DEMs translates into uncertainties in modelled inundation is needed to ensure results are appropriately interpreted and used. This assessment can in turn informdata acquisition strategies depending on the purpose of the inundation model. For example, lower accuracy elevation data may give inundation results that are sufficiently accurate to plan a community's evacuation route but not sufficient to inform engineering of a vertical evacuation shelters. A sensitivity study is undertaken to assess the utility of different available onshore digital elevation models for tsunami inundation modelling. We compare airborne interferometric synthetic aperture radar (IFSAR), ASTER and SRTM against high resolution (<1 m horizontal resolution, < 0.15 m vertical accuracy) LiDAR or stereo-camera data in three Indonesian locations with different coastal morphologies (Padang, West Sumatra; Palu, Central Sulawesi; and Maumere, Flores), using three different computational codes (ANUGA, TUNAMI-N3 and TsunAWI). Tsunami inundation extents modelled with IFSAR are comparable with those modelled with the high resolution datasets and with historical tsunami run-up data. Large vertical errors (> 10 m) and poor resolution of the coastline in the ASTER and SRTM elevation models cause modelled inundation to be much less compared with models using better data and with observations. Therefore we recommend that ASTER and SRTM should not be used for modelling tsunami inundation in order to determine tsunami extent or any other measure of onshore tsunami hazard. We suggest that for certain disaster management applications where the important factor is the extent of inundation, such as evacuation planning, airborne IFSAR provides a good compromise between cost and accuracy; however the representation of flow parameters such as depth and velocity is not sufficient to inform detailed engineering of structures. Differences in modelled inundation extent between digital terrain models (DTM) and digital surface models (DSM) for LiDAR, high resolution stereo-camera and airborne IFSAR data are greater than differences between the data types. The presence of trees and buildings as solid elevation in the DSM leads to underestimated inundation extents compared with observations, while removal of these features in the DTM causes more extensive inundation. Further work is needed to resolve whether DTM or DSM should be used and, in particular for DTM, how and at what spatial scale roughness should be parameterized to appropriately account for the presence of buildings and vegetation. We also test model mesh resolutions up to 0.8 m but find that there are only negligible changes in inundation extent between 0.8 and 25 m mesh resolution, even using the highest resolution elevation data.

Development of a flood-warning system and flood-inundation mapping in Licking County, Ohio

USGS Publications Warehouse

Ostheimer, Chad J.

2012-01-01

Digital flood-inundation maps for selected reaches of South Fork Licking River, Raccoon Creek, North Fork Licking River, and the Licking River in Licking County, Ohio, were created by the U.S. Geological Survey (USGS), in cooperation with the Ohio Department of Transportation; U.S. Department of Transportation, Federal Highway Administration; Muskingum Watershed Conservancy District; U.S. Department of Agriculture, Natural Resources Conservation Service; and the City of Newark and Village of Granville, Ohio. The inundation maps depict estimates of the areal extent of flooding corresponding to water levels (stages) at the following USGS streamgages: South Fork Licking River at Heath, Ohio (03145173); Raccoon Creek below Wilson Street at Newark, Ohio (03145534); North Fork Licking River at East Main Street at Newark, Ohio (03146402); and Licking River near Newark, Ohio (03146500). The maps were provided to the National Weather Service (NWS) for incorporation into a Web-based flood-warning system that can be used in conjunction with NWS flood-forecast data to show areas of predicted flood inundation associated with forecasted flood-peak stages. As part of the flood-warning streamflow network, the USGS re-installed one streamgage on North Fork Licking River, and added three new streamgages, one each on North Fork Licking River, South Fork Licking River, and Raccoon Creek. Additionally, the USGS upgraded a lake-level gage on Buckeye Lake. Data from the streamgages and lake-level gage can be used by emergency-management personnel, in conjunction with the flood-inundation maps, to help determine a course of action when flooding is imminent. Flood profiles for selected reaches were prepared by calibrating steady-state step-backwater models to selected, established streamgage rating curves. The step-backwater models then were used to determine water-surface-elevation profiles for up to 10 flood stages at a streamgage with corresponding streamflows ranging from approximately the 50 to 0.2-percent chance annual-exceedance probabilities for each of the 4 streamgages that correspond to the flood-inundation maps. The computed flood profiles were used in combination with digital elevation data to delineate flood-inundation areas. Maps of Licking County showing flood-inundation areas overlain on digital orthophotographs are presented for the selected floods. The USGS also developed an unsteady-flow model for a reach of South Fork Licking River for use by the NWS to enhance their ability to provide advanced flood warning in the region north of Buckeye Lake, Ohio. The unsteady-flow model was calibrated based on data from four flooding events that occurred from June 2008 to December 2011. Model calibration was approximate due to the fact that there were unmeasured inflows to the river that were not able to be considered during the calibration. Information on unmeasured inflow derived from NWS hydrologic models and additional flood-event data could enable the NWS to further refine the unsteady-flow model.

Estimates of future inundation of salt marshes in response to sea-level rise in and around Acadia National Park, Maine

USGS Publications Warehouse

Nielsen, Martha G.; Dudley, Robert W.

2013-01-01

Salt marshes are ecosystems that provide many important ecological functions in the Gulf of Maine. The U.S. Geological Survey investigated salt marshes in and around Acadia National Park from Penobscot Bay to the Schoodic Peninsula to map the potential for landward migration of marshes using a static inundation model of a sea-level rise scenario of 60 centimeters (cm; 2 feet). The resulting inundation contours can be used by resource managers to proactively adapt to sea-level rise by identifying and targeting low-lying coastal areas adjacent to salt marshes for conservation or further investigation, and to identify risks to infrastructure in the coastal zone. For this study, the mapping of static inundation was based on digital elevation models derived from light detection and ranging (LiDAR) topographic data collected in October 2010. Land-surveyed control points were used to evaluate the accuracy of the LiDAR data in the study area, yielding a root mean square error of 11.3 cm. An independent accuracy assessment of the LiDAR data specific to salt-marsh land surfaces indicated a root mean square error of 13.3 cm and 95-percent confidence interval of ± 26.0 cm. LiDAR-derived digital elevation models and digital color aerial photography, taken during low tide conditions in 2008, with a pixel resolution of 0.5 meters, were used to identify the highest elevation of the land surface at each salt marsh in the study area. Inundation contours for 60-cm of sea-level rise were delineated above the highest marsh elevation for each marsh. Confidence interval contours (95-percent,± 26.0 cm) were delineated above and below the 60-cm inundation contours, and artificial structures, such as roads and bridges, that may present barriers to salt-marsh migration were mapped. This study delineated 114 salt marshes totaling 340 hectares (ha), ranging in size from 0.11 ha (marshes less than 0.2 ha were mapped only if they were on Acadia National Park property) to 52 ha, with a median size of 1.0 ha. Inundation contours were mapped at 110 salt marshes. Approximately 350 ha of low-lying upland areas adjacent to these marshes will be inundated with 60 cm of sea-level rise. Many of these areas are currently freshwater wetlands. There are potential barriers to marsh migration at 27 of the 114 marshes. Although only 23 percent of the salt marshes in the study are on ANP property, about half of the upland areas that will be inundated are within ANP; most of the predicted inundated uplands (approximately 170 ha) include freshwater wetlands in the Northeast Creek and Bass Harbor Marsh areas. Most of the salt marshes analyzed do not have a significant amount of upland area available for migration. Seventy-five percent of the salt marshes have 20 meters or less of adjacent upland that would be inundated along most of their edges. All inundation contours, salt marsh locations, potential barriers, and survey data are stored in geospatial files for use in a geographic information system and are a part of this report.

Flood inundation maps for the Wabash and Eel Rivers at Logansport, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for an 8.3-mile reach of the Wabash River and a 7.6-mile reach of the Eel River at Logansport, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage Wabash River at Logansport, Ind. (sta. no. 03329000) and USGS streamgage Eel River near Logansport, Ind. (sta. no. 03328500). Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgages 03329000, Wabash River at Logansport, Ind., and 03328500, Eel River near Logansport, Ind. The calibrated hydraulic model was then used to determine five water-surface profiles for flood stage at 1-foot intervals referenced to the Wabash River streamgage datum, and four water-surface profiles for flood stages at 1-foot intervals referenced to the Eel River streamgage datum. The stages range from bankfull to approximately the highest stages that have occurred since 1967 when three flood control dams were built upstream of Logansport, Ind. The simulated water-surface profiles were then combined with a geographic information system (GIS) digital elevation model (DEM, derived from Light Detection and Ranging [lidar] data having a 0.37-foot vertical accuracy and 3.9-foot horizontal resolution) in order to delineate the area flooded at each stage. The availability of these maps, along with information available on the Internet regarding current stages from the USGS streamgages at Logansport, Ind., and forecasted stream stages from the NWS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post flood recovery efforts.

Flood-inundation maps for the Saddle River from Upper Saddle River Borough to Saddle River Borough, New Jersey, 2013

USGS Publications Warehouse

Watson, Kara M.; Hoppe, Heidi L.

2013-01-01

Digital flood-inundation maps for a 4.1-mile reach of the Saddle River from 0.6 miles downstream from the New Jersey-New York State boundary in Upper Saddle River Borough to 0.2 miles downstream from the East Allendale Road bridge in Saddle River Borough, New Jersey, were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection (NJDEP). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at the USGS streamgage 01390450, Saddle River at Upper Saddle River, New Jersey. Current conditions for estimating near real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/nwis/uv?site_no=01390450. The National Weather Service (NWS) forecasts flood hydrographs at many places that are often collocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relations (in effect March 2013) at USGS streamgage 01390450, Saddle River at Upper Saddle River, New Jersey, and documented high-water marks from recent floods. The hydraulic model was then used to determine eight water-surface profiles for flood stages at 0.5-foot (ft) intervals referenced to the streamgage datum, North American Vertical Datum of 1988 (NAVD 88), and ranging from bankfull, 0.5 ft below NWS Action Stage, to the upper extent of the stage-discharge rating which is approximately 1 ft higher than the highest recorded water level at the streamgage. Action Stage is the stage which when reached by a rising stream the NWS or a partner needs to take some type of mitigation action in preparation for possible significant hydrologic activity. The simulated water-surface profiles were then combined with a geographic information system 3-meter (9.84 ft) digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The availability of these maps along with real-time streamflow data and information regarding current stage from USGS streamgages and forecasted stream stages from the NWS provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the Saddle River from Rochelle Park to Lodi, New Jersey, 2012

USGS Publications Warehouse

Hoppe, Heidi L.; Watson, Kara M.

2012-01-01

Digital flood-inundation maps for a 2.75-mile reach of the Saddle River from 0.2 mile upstream from the Interstate 80 bridge in Rochelle Park to 1.5 miles downstream from the U.S. Route 46 bridge in Lodi, New Jersey, were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection (NJDEP). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Saddle River at Lodi, New Jersey (station 01391500). Current conditions for estimating near real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/nwis/uv?site_no=01391500. The National Weather Service (NWS) forecasts flood hydrographs at many places that are often collocated with USGS streamgages. NWS-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at the Saddle River at Lodi, New Jersey streamgage and documented high-water marks from recent floods. The hydraulic model was then used to determine 11 water-surface profiles for flood stages at the Saddle River streamgage at 1-ft intervals referenced to the streamgage datum, North American Vertical Datum of 1988 (NAVD 88), and ranging from bankfull, 0.5 ft below NWS Action Stage, to the extent of the stage-discharge rating, which is approximately 1 ft higher than the highest recorded water level at the streamgage. Action Stage is the stage which when reached by a rising stream the NWS or a partner needs to take some type of mitigation action in preparation for possible significant hydrologic activity. The simulated water-surface profiles were then combined with a geographic information system 3-meter (9.84-ft) digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the Patoka River in and near Jasper, southwestern Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2018-01-23

Digital flood-inundation maps for a 9.5-mile reach of the Patoka River in and near the city of Jasper, southwestern Indiana (Ind.), from the streamgage near County Road North 175 East, downstream to State Road 162, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage Patoka River at Jasper, Ind. (station number 03375500). The Patoka streamgage is located at the upstream end of the 9.5-mile river reach. Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, although flood forecasts and stages for action and minor, moderate, and major flood stages are not currently (2017) available at this site (JPRI3).Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at the Patoka River at Jasper, Ind., streamgage and the documented high-water marks from the flood of April 30, 2017. The calibrated hydraulic model was then used to compute five water-surface profiles for flood stages referenced to the streamgage datum ranging from 15 feet (ft), or near bankfull, to 19 ft. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging [lidar] data having a 0.98 ft vertical accuracy and 4.9 ft horizontal resolution) to delineate the area flooded at each water level.The availability of these flood-inundation maps, along with real-time stage from the USGS streamgage at the Patoka River at Jasper, Ind., will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for postflood recovery efforts.

Real-time determination of the worst tsunami scenario based on Earthquake Early Warning

NASA Astrophysics Data System (ADS)

Furuya, Takashi; Koshimura, Shunichi; Hino, Ryota; Ohta, Yusaku; Inoue, Takuya

2016-04-01

In recent years, real-time tsunami inundation forecasting has been developed with the advances of dense seismic monitoring, GPS Earth observation, offshore tsunami observation networks, and high-performance computing infrastructure (Koshimura et al., 2014). Several uncertainties are involved in tsunami inundation modeling and it is believed that tsunami generation model is one of the great uncertain sources. Uncertain tsunami source model has risk to underestimate tsunami height, extent of inundation zone, and damage. Tsunami source inversion using observed seismic, geodetic and tsunami data is the most effective to avoid underestimation of tsunami, but needs to expect more time to acquire the observed data and this limitation makes difficult to terminate real-time tsunami inundation forecasting within sufficient time. Not waiting for the precise tsunami observation information, but from disaster management point of view, we aim to determine the worst tsunami source scenario, for the use of real-time tsunami inundation forecasting and mapping, using the seismic information of Earthquake Early Warning (EEW) that can be obtained immediately after the event triggered. After an earthquake occurs, JMA's EEW estimates magnitude and hypocenter. With the constraints of earthquake magnitude, hypocenter and scaling law, we determine possible multi tsunami source scenarios and start searching the worst one by the superposition of pre-computed tsunami Green's functions, i.e. time series of tsunami height at offshore points corresponding to 2-dimensional Gaussian unit source, e.g. Tsushima et al., 2014. Scenario analysis of our method consists of following 2 steps. (1) Searching the worst scenario range by calculating 90 scenarios with various strike and fault-position. From maximum tsunami height of 90 scenarios, we determine a narrower strike range which causes high tsunami height in the area of concern. (2) Calculating 900 scenarios that have different strike, dip, length, width, depth and fault-position. Note that strike is limited with the range obtained from 90 scenarios calculation. From 900 scenarios, we determine the worst tsunami scenarios from disaster management point of view, such as the one with shortest travel time and the highest water level. The method was applied to a hypothetical-earthquake, and verified if it can effectively search the worst tsunami source scenario in real-time, to be used as an input of real-time tsunami inundation forecasting.

Flood-inundation maps for the Withlacoochee River From Skipper Bridge Road to St. Augustine Road, within the City of Valdosta, Georgia, and Lowndes County, Georgia

USGS Publications Warehouse

Musser, Jonathan W.

2018-01-31

Digital flood-inundation maps for a 12.6-mile reach of the Withlacoochee River from Skipper Bridge Road to St. Augustine Road (Georgia State Route 133) were developed to depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey (USGS) streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483). Real-time stage information from this streamgage can be used with these maps to estimate near real-time areas of inundation. The forecasted peak-stage information for the USGS streamgage at Withlacoochee River at Skipper Bridge Road, near Bemiss, Ga. (023177483), can be used in conjunction with the maps developed for this study to show predicted areas of flood inundation.A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers Hydrologic Engineer-ing Center’s River Analysis System (HEC–RAS) software for the Withlacoochee River and was used to compute flood profiles for a 12.6-mile reach of the Withlacoochee River. The hydraulic model was then used to simulate 23 water-surface profiles at 1.0-foot (ft) intervals at the Withlacoochee River near the Bemiss streamgage. The profiles ranged from the National Weather Service action stage of 10.7 ft, which is 131.0 ft above the North American Vertical Datum of 1988 (NAVD 88), to a stage of 32.7 ft, which is 153.0 ft above NAVD 88. The simulated water-surface profiles were then combined with a geographic information system digital elevation model—derived from light detection and ranging (lidar) data having a 4.0-ft horizontal resolution—to delineate the area flooded at each 1.0-ft interval of stream stage.

Constructing river stage-discharge rating curves using remotely sensed river cross-sectional inundation areas and river bathymetry

NASA Astrophysics Data System (ADS)

Pan, Feifei; Wang, Cheng; Xi, Xiaohuan

2016-09-01

Remote sensing from satellites and airborne platforms provides valuable data for monitoring and gauging river discharge. One effective approach first estimates river stage from satellite-measured inundation area based on the inundation area-river stage relationship (IARSR), and then the estimated river stage is used to compute river discharge based on the stage-discharge rating (SDR) curve. However, this approach is difficult to implement because of a lack of data for constructing the SDR curves. This study proposes a new method to construct the SDR curves using remotely sensed river cross-sectional inundation areas and river bathymetry. The proposed method was tested over a river reach between two USGS gauging stations, i.e., Kingston Mines (KM) and Copperas Creek (CC) along the Illinois River. First a polygon over each of two cross sections was defined. A complete IARSR curve was constructed inside each polygon using digital elevation model (DEM) and river bathymetric data. The constructed IARSR curves were then used to estimate 47 river water surface elevations at each cross section based on 47 river inundation areas estimated from Landsat TM images collected during 1994-2002. The estimated water surface elevations were substituted into an objective function formed by the Bernoulli equation of gradually varied open channel flow. A nonlinear global optimization scheme was applied to solve the Manning's coefficient through minimizing the objective function value. Finally the SDR curve was constructed at the KM site using the solved Manning's coefficient, channel cross sectional geometry and the Manning's equation, and employed to estimate river discharges. The root mean square error (RMSE) in the estimated river discharges against the USGS measured river discharges is 112.4 m3/s. To consider the variation of the Manning's coefficient in the vertical direction, this study also suggested a power-law function to describe the vertical decline of the Manning's coefficient with the water level from the channel bed lowest elevation to the bank-full level. The constructed SDR curve with the vertical variation of the Manning's coefficient reduced the RMSE in the estimated river discharges to 83.9 m3/s. These results indicate that the method developed and tested in this study is effective and robust, and has the potential for improving our ability of remote sensing of river discharge and providing data for water resources management, global water cycle study, and flood forecasting and prevention.

Flood Inundation Modelling in the Kuantan River Basin using 1D-2D Flood Modeller coupled with ASTER-GDEM

NASA Astrophysics Data System (ADS)

Ng, Z. F.; Gisen, J. I.; Akbari, A.

2018-03-01

Topography dataset is an important input in performing flood inundation modelling. However, it is always difficult to obtain high resolution topography that provide accurate elevation information. Fortunately, there are some open source topography datasets available with reasonable resolution such as SRTM and ASTER-GDEM. In Malaysia particularly in Kuantan, the modelling research on the floodplain area is still lacking. This research aims to: a) to investigate the suitability of ASTER-GDEM to be applied in the 1D-2D flood inundation modelling for the Kuantan River Basin; b) to generate flood inundation map for Kuantan river basin. The topography dataset used in this study is ASTER-GDEM to generate physical characteristics of watershed in the basin. It is used to perform rainfall runoff modelling for hydrological studies and to delineate flood inundation area in the Flood Modeller. The results obtained have shown that a 30m resolution ASTER-GDEM is applicable as an input for the 1D-2D flood modelling. The simulated water level in 2013 has NSE of 0.644 and RSME of 1.259. As a conclusion, ASTER-GDEM can be used as one alternative topography datasets for flood inundation modelling. However, the flood level obtained from the hydraulic modelling shows low accuracy at flat urban areas.

Effect of uncertainty in Digital Surface Models on the boundary of inundated areas

NASA Astrophysics Data System (ADS)

Nalbantis, I.; Papageorgaki, I.; Sioras, P.; Ioannidis, Ch.

2012-04-01

The planning, design and operation of flood damage reduction works or non-structural measures require the construction of maps that indicate zones to be potentially inundated during floods. Referring to floods due to heavy rainfall, the common procedure for flood mapping consists of the following five computational steps: (1) Frequency analysis of extreme rainfall; (2) construction of design hyetographs for various return periods; (3) construction of the related direct runoff hydrographs; (4) routing of these hydrographs through the hydrographic network; (5) mapping of the inundated area that corresponds to the temporally maximum depth for each location in the flood plain. Steps 3 through 5 require the use of spatial information which can be easily obtained from a Digital Surface Model (DSM). The DSM contains grid-based elevations of the ground or overlying objects that influence the propagation of flood waves. In this work, the SCS-CN method is used in step 3 in combination with a synthetic Unit Hydrograph based on the SCS dimensionless Unit Hydrograph. In step 4, the full one-dimensional Saint Venant equations for non-uniform unsteady flow on fixed bed are used, which are numerically solved. The impact of uncertainty in the DSM on the inundated area boundary is investigated. For this the Monte Carlo simulation method is employed to produce a large number of erroneous DSMs through introducing errors in elevation with a standard deviation equal to σ. These DSMs are then used for delineating potentially flooded areas. The standard deviation of the distance (from the riverbed axis) of the boundary of these areas, herein denoted as σF, is used as the measure of the resulting uncertainty. The link between σ and σF is examined for a spectrum of large return periods (100 to 10000). A computer experiment was set up based on data from two drainage basins. The first basin is located in East Attica and is drained by a branch of the Erasinos Torrent named the South-East Kalyvia Torrent; it extends over an area of about 17 square kilometres. The second basin is that of the Kerynitis River in north-western Peloponnesus; it covers an area of 89 square kilometres. In each one of the two basins hydrographs at the outlet of the upper part of the basin are estimated with the aid of hydrological modelling, while, for the lower part hydraulic routing is employed. The South-East Kalyvia basin is hilly, whereas the Kerynitis Basin shows high ground slopes in its upper part and low slopes in the lower part. Graphs of σ vs. σF and maps showing the mean position μF of the boundary of flooded area along with limits of this boundary that reflect positions μF±2σF help visualize the impact of the uncertainty in DSM. To acquire a better feeling of the effect of DSM uncertainty, results are compared to those obtained from uncertain rainfall depths of the design hyetographs.

Flood-inundation maps for the Yellow River at Plymouth, Indiana

USGS Publications Warehouse

Menke, Chad D.; Bunch, Aubrey R.; Kim, Moon H.

2016-11-16

Digital flood-inundation maps for a 4.9-mile reach of the Yellow River at Plymouth, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 05516500, Yellow River at Plymouth, Ind. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/uv?site_no=05516500. In addition, information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http:/water.weather.gov/ahps/). The NWS AHPS forecasts flood hydrographs at many sites that are often collocated with USGS streamgages, including the Yellow River at Plymouth, Ind. NWS AHPS-forecast peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas of flood and forecasts of flood hydrographs at this site.For this study, flood profiles were computed for the Yellow River reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the current stage-discharge relations at the Yellow River streamgage, in combination with the flood-insurance study for Marshall County (issued in 2011). The calibrated hydraulic model was then used to determine eight water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the highest stage of the current stage-discharge rating curve. The 1-percent annual exceedance probability flood profile elevation (flood elevation with recurrence intervals within 100 years) is within the calibrated water-surface elevations for comparison. The simulated water-surface profiles were then used with a geographic information system (GIS) digital elevation model (DEM, derived from Light Detection and Ranging [lidar]) in order to delineate the area flooded at each water level.The availability of these maps, along with Internet information regarding current stage from the USGS streamgage 05516500, Yellow River at Plymouth, Ind., and forecast stream stages from the NWS AHPS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Flood-inundation maps for a 6.5-mile reach of the Kentucky River at Frankfort, Kentucky

USGS Publications Warehouse

Lant, Jeremiah G.

2013-01-01

Digital flood-inundation maps for a 6.5-mile reach of Kentucky River at Frankfort, Kentucky, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Frankfort Office of Emergency Management. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage Kentucky River at Lock 4 at Frankfort, Kentucky (station no. 03287500). Current conditions for the USGS streamgage may be obtained online at the USGS National Water Information System site (http://waterdata.usgs.gov/nwis/inventory?agency_code=USGS&site_no=03287500). In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated at USGS streamgages. The forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the Kentucky River reach by using HEC–RAS, a one-dimensional step-backwater model developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated by using the most current (2013) stage-discharge relation for the Kentucky River at Lock 4 at Frankfort, Kentucky, in combination with streamgage and high-water-mark measurements collected for a flood event in May 2010. The calibrated model was then used to calculate 26 water-surface profiles for a sequence of flood stages, at 1-foot intervals, referenced to the streamgage datum and ranging from a stage near bankfull to the elevation that breached the levees protecting the City of Frankfort. To delineate the flooded area at each interval flood stage, the simulated water-surface profiles were combined with a digital elevation model (DEM) of the study area by using geographic information system software. The DEM consisted of bare-earth elevations within the study area and was derived from a Light Detection And Ranging (LiDAR) dataset having a 5.0-foot horizontal resolution and an accuracy of 0.229 foot. The availability of these maps, along with Internet information regarding current stages from USGS streamgages and forecasted stages from the NWS, provides emergency management personnel and local residents with critical information for flood response activities such as evacuations, road closures, and postflood recovery efforts.

Vulnerability assessment of the impact of sea-level rise and flooding on the Moroccan coast: The case of the Mediterranean eastern zone

NASA Astrophysics Data System (ADS)

Snoussi, Maria; Ouchani, Tachfine; Niazi, Saïda

2008-04-01

The eastern part of the Mediterranean coast of Morocco is physically and socio-economically vulnerable to accelerated sea-level rise, due to its low topography and its high ecological and touristic value. Assessment of the potential land loss by inundation has been based on empirical approaches using a minimum inundation level of 2 m and a maximum inundation level of 7 m, where scenarios for future sea-level rise range from 200 to 860 mm, with a 'best estimate' of 490 mm. The socio-economic impacts have been based on two possible alternative futures: (1) a 'worst-case' scenario, obtained by combining the 'economic development first' scenario with the maximum inundation level; and (2) a 'best-case' scenario, by combining the 'sustainability first' scenario with the minimum inundation level. Inundation analysis, based on Geographical Information Systems and a modelling approach to erosion, has identified both locations and the socioeconomic sectors that are most at risk to accelerated sea-level rise. Results indicate that 24% and 59% of the area will be lost by flooding at minimum and maximum inundation levels, respectively. The most severely impacted sectors are expected to be the residential and recreational areas, agricultural land, and the natural ecosystem. Shoreline erosion will affect 50% and 70% of the total area in 2050 and 2100, respectively. Potential strategies to ameliorate the impact of seawater inundation include: wetland preservation; beach nourishment at tourist resorts; and the afforestation of dunes. As this coast is planned to become one of the most developed tourist resorts in Morocco by 2010, measures such as building regulation, urban growth planning and development of an Integrated Coastal Zone Management Plan, are recommended for the region.

Evaluation of dynamic coastal response to sea-level rise modifies inundation likelihood

USGS Publications Warehouse

Lentz, Erika E.; Thieler, E. Robert; Plant, Nathaniel G.; Stippa, Sawyer R.; Horton, Radley M.; Gesch, Dean B.

2016-01-01

Sea-level rise (SLR) poses a range of threats to natural and built environments1, 2, making assessments of SLR-induced hazards essential for informed decision making3. We develop a probabilistic model that evaluates the likelihood that an area will inundate (flood) or dynamically respond (adapt) to SLR. The broad-area applicability of the approach is demonstrated by producing 30 × 30 m resolution predictions for more than 38,000 km2 of diverse coastal landscape in the northeastern United States. Probabilistic SLR projections, coastal elevation and vertical land movement are used to estimate likely future inundation levels. Then, conditioned on future inundation levels and the current land-cover type, we evaluate the likelihood of dynamic response versus inundation. We find that nearly 70% of this coastal landscape has some capacity to respond dynamically to SLR, and we show that inundation models over-predict land likely to submerge. This approach is well suited to guiding coastal resource management decisions that weigh future SLR impacts and uncertainty against ecological targets and economic constraints.

Flood-inundation maps for North Fork Salt Creek at Nashville, Indiana

USGS Publications Warehouse

Martin, Zachary W.

2017-11-13

Digital flood-inundation maps for a 3.2-mile reach of North Fork Salt Creek at Nashville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding that correspond to selected water levels (stages) at the North Fork Salt Creek at Nashville, Ind., streamgage (USGS station number 03371650). Real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also shows observed USGS stages at the same site as the USGS streamgage (NWS site NFSI3).Flood profiles were computed for the stream reach by means of a one-dimensional, step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current (2015) stage-discharge rating at the USGS streamgage 03371650, North Fork Salt Creek at Nashville, Ind. The hydraulic model was then used to compute 12 water-surface profiles for flood stages at 1-foot (ft) intervals, except for the highest profile of 22.9 ft, referenced to the streamgage datum ranging from 12.0 ft (the NWS “action stage”) to 22.9 ft, which is the highest stage of the current (2015) USGS stage-discharge rating curve and 1.9 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability of these maps, along with information regarding current stage from the USGS streamgage, will provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for postflood recovery efforts.

Computational Design Tool for Bridge Hydrodynamic Loading in Inundated Flows of Midwest Rivers

DOT National Transportation Integrated Search

2009-12-01

The hydraulic forces experienced by an inundated bridge deck have great importance in the design of bridges. The proper estimation of loading exerted by the flow on the structure is important for design plans and is pertinent for evaluating its vulne...

High Resolution Hurricane Storm Surge and Inundation Modeling (Invited)

NASA Astrophysics Data System (ADS)

Luettich, R.; Westerink, J. J.

2010-12-01

Coastal counties are home to nearly 60% of the U.S. population and industry that accounts for over 16 million jobs and 10% of the U.S. annual gross domestic product. However, these areas are susceptible to some of the most destructive forces in nature, including tsunamis, floods, and severe storm-related hazards. Since 1900, tropical cyclones making landfall on the US Gulf of Mexico Coast have caused more than 9,000 deaths; nearly 2,000 deaths have occurred during the past half century. Tropical cyclone-related adjusted, annualized losses in the US have risen from 1.3 billion from 1949-1989, to 10.1 billion from 1990-1995, and $35.8 billion per year for the period 2001-2005. The risk associated with living and doing business in the coastal areas that are most susceptible to tropical cyclones is exacerbated by rising sea level and changes in the characteristics of severe storms associated with global climate change. In the five years since hurricane Katrina devastated the northern Gulf of Mexico Coast, considerable progress has been made in the development and utilization of high resolution coupled storm surge and wave models. Recent progress will be presented with the ADCIRC + SWAN storm surge and wave models. These tightly coupled models use a common unstructured grid in the horizontal that is capable of covering large areas while also providing high resolution (i.e., base resolution down to 20m plus smaller subgrid scale features such as sea walls and levees) in areas that are subject to surge and inundation. Hydrodynamic friction and overland winds are adjusted to account for local land cover. The models scale extremely well on modern high performance computers allowing rapid turnaround on large numbers of compute cores. The models have been adopted for FEMA National Flood Insurance Program studies, hurricane protection system design and risk analysis, and quasi-operational forecast systems for several regions of the country. They are also being evaluated as part of a NOAA IOOS national storm surge/inundation model test bed program.

High resolution tsunami modelling for the evaluation of potential risk areas in Setúbal (Portugal)

NASA Astrophysics Data System (ADS)

Ribeiro, J.; Silva, A.; Leitão, P.

2011-08-01

The use of high resolution hydrodynamic modelling to simulate the potential effects of tsunami events can provide relevant information about the most probable inundation areas. Moreover, the consideration of complementary data such as the type of buildings, location of priority equipment, type of roads, enables mapping of the most vulnerable zones, computing of the expected damage on man-made structures, constrain of the definition of rescue areas and escape routes, adaptation of emergency plans and proper evaluation of the vulnerability associated with different areas and/or equipment. Such an approach was used to evaluate the specific risks associated with a potential occurrence of a tsunami event in the region of Setúbal (Portugal), which was one of the areas most seriously affected by the 1755 tsunami. In order to perform an evaluation of the hazard associated with the occurrence of a similar event, high resolution wave propagation simulations were performed considering different potential earthquake sources with different magnitudes. Based on these simulations, detailed inundation maps associated with the different events were produced. These results were combined with the available information on the vulnerability of the local infrastructures (building types, roads and streets characteristics, priority buildings) in order to impose restrictions in the production of high-scale potential damage maps, escape routes and emergency routes maps.

Flood-inundation maps for the West Branch Susquehanna River near the Boroughs of Lewisburg and Milton, Pennsylvania

USGS Publications Warehouse

Roland, Mark A.; Hoffman, Scott A.

2014-01-01

Digital flood-inundation maps for an approximate 8-mile reach of the West Branch Susquehanna River from approximately 2 miles downstream from the Borough of Lewisburg, extending upstream to approximately 1 mile upstream from the Borough of Milton, Pennsylvania, were created by the U.S. Geological Survey (USGS) in cooperation with the Susquehanna River Basin Commission (SRBC). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict the estimated areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa. In addition, the information has been provided to the Susquehanna River Basin Commission (SRBC) for incorporation into their Susquehanna Inundation Map Viewer (SIMV) flood warning system (http://maps.srbc.net/simv/). The National Weather Service (NWS) forecasted peak-stage information (http://water.weather.gov/ahps) for USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa., may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. Calibration of the model was achieved using the most current stage-discharge relations (rating number 11.1) at USGS streamgage 01553500, West Branch Susquehanna River at Lewisburg, Pa., a documented water-surface profile from the December 2, 2010, flood, and recorded peak stage data. The hydraulic model was then used to determine 26 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum ranging from 14 feet (ft) to 39 ft. Modeled flood stages, as defined by NWS, include Action Stage, 14 ft; Flood Stage, 18 ft; Moderate Flood Stage, 23 ft; and Major Flood Stage, 28 ft. Geographic information system (GIS) technology was then used to combine the simulated water-surface profiles with a digital elevation model (DEM) derived from light detection and ranging (lidar) data to delineate the area flooded at each water level. The availability of these maps, along with World Wide Web information regarding current stage from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

LIDAR vs. GEODAS land elevation data in hurricane induced inundation modelling

NASA Astrophysics Data System (ADS)

Peng, M.; Pietrafesa, L. J.; Bao, S.; Liu, H.; Xia, M.; Yan, T.

2007-04-01

LIDAR (Light Detection and Ranging) and GEODAS (GEOphysical DAta System) are respectively taken as the land elevation data for a 3-D storm surge and inundation model to investigate the subsequent inundation differences. Hilton Head, South Carolina, and Croatan-Albemarle-Pamlico Estuary System (CAPES), North Carolina, are the two investigated regions. Significant inundation differences with LIDAR versus GEODAS are found in both regions. The modeled inundation area with GEODAS is larger than with LIDAR. For Category 2-3 hypothetical hurricanes, the maximum inundation difference in Hilton Head region is 67%, while the difference in the CAPES is 156%. Generally, vertical precision difference of the two databases is the major reason for the inundation difference. Recently constructed man-made structures, not included in the GEODAS, but included in the LIDAR data sets may be another contributing reason.

Scenario based approach for multiple source Tsunami Hazard assessment for Sines, Portugal

NASA Astrophysics Data System (ADS)

Wronna, M.; Omira, R.; Baptista, M. A.

2015-08-01

In this paper, we present a scenario-based approach for tsunami hazard assessment for the city and harbour of Sines - Portugal, one of the test-sites of project ASTARTE. Sines holds one of the most important deep-water ports which contains oil-bearing, petrochemical, liquid bulk, coal and container terminals. The port and its industrial infrastructures are facing the ocean southwest towards the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, we selected a total of six scenarios to assess the tsunami impact at the test site. The tsunami simulations are computed using NSWING a Non-linear Shallow Water Model With Nested Grids. In this study, the static effect of tides is analysed for three different tidal stages MLLW (mean lower low water), MSL (mean sea level) and MHHW (mean higher high water). For each scenario, inundation is described by maximum values of wave height, flow depth, drawback, runup and inundation distance. Synthetic waveforms are computed at virtual tide gauges at specific locations outside and inside the harbour. The final results describe the impact at Sines test site considering the single scenarios at mean sea level, the aggregate scenario and the influence of the tide on the aggregate scenario. The results confirm the composite of Horseshoe and Marques Pombal fault as the worst case scenario. It governs the aggregate scenario with about 60 % and inundates an area of 3.5 km2.

Tsunami vulnerability assessment mapping for the west coast of Peninsular Malaysia using a geographical information system (GIS)

NASA Astrophysics Data System (ADS)

Najihah, R.; Effendi, D. M.; Hairunnisa, M. A.; Masiri, K.

2014-02-01

The catastrophic Indian Ocean tsunami of 26 December 2004 raised a number of questions for scientist and politicians on how to deal with the tsunami risk and assessment in coastal regions. This paper discusses the challenges in tsunami vulnerability assessment and presents the result of tsunami disaster mapping and vulnerability assessment study for West Coast of Peninsular Malaysia. The spatial analysis was carried out using Geographical Information System (GIS) technology to demarcate spatially the tsunami affected village's boundary and suitable disaster management program can be quickly and easily developed. In combination with other thematic maps such as road maps, rail maps, school maps, and topographic map sheets it was possible to plan the accessibility and shelter to the affected people. The tsunami vulnerability map was used to identify the vulnerability of villages/village population to tsunami. In the tsunami vulnerability map, the intensity of the tsunami was classified as hazard zones based on the inundation level in meter (contour). The approach produced a tsunami vulnerability assessment map consists of considering scenarios of plausible extreme, tsunami-generating events, computing the tsunami inundation levels caused by different events and scenarios and estimating the possible range of casualties for computing inundation levels. The study provides an interactive means to identify the tsunami affected areas after the disaster and mapping the tsunami vulnerable village before for planning purpose were the essential exercises for managing future disasters.

Coupling high-resolution hydraulic and hydrologic models for flash flood forecasting and inundation mapping in urban areas - A case study for the City of Fort Worth

NASA Astrophysics Data System (ADS)

Nazari, B.; Seo, D.; Cannon, A.

2013-12-01

With many diverse features such as channels, pipes, culverts, buildings, etc., hydraulic modeling in urban areas for inundation mapping poses significant challenges. Identifying the practical extent of the details to be modeled in order to obtain sufficiently accurate results in a timely manner for effective emergency management is one of them. In this study we assess the tradeoffs between model complexity vs. information content for decision making in applying high-resolution hydrologic and hydraulic models for real-time flash flood forecasting and inundation mapping in urban areas. In a large urban area such as the Dallas-Fort Worth Metroplex (DFW), there exists very large spatial variability in imperviousness depending on the area of interest. As such, one may expect significant sensitivity of hydraulic model results to the resolution and accuracy of hydrologic models. In this work, we present the initial results from coupling of high-resolution hydrologic and hydraulic models for two 'hot spots' within the City of Fort Worth for real-time inundation mapping.

A New Approach to Monitoring Coastal Marshes for Persistent Flooding

NASA Astrophysics Data System (ADS)

Kalcic, M. T.; Underwood, L. W.; Fletcher, R. M.

2012-12-01

Many areas in coastal Louisiana are below sea level and protected from flooding by a system of natural and man-made levees. Flooding is common when the levees are overtopped by storm surge or rising rivers. Many levees in this region are further stressed by erosion and subsidence. The floodwaters can become constricted by levees and trapped, causing prolonged inundation. Vegetative communities in coastal regions, from fresh swamp forest to saline marsh, can be negatively affected by inundation and changes in salinity. As saltwater persists, it can have a toxic effect upon marsh vegetation causing die off and conversion to open water types, destroying valuable species habitats. The length of time the water persists and the average annual salinity are important variables in modeling habitat switching (cover type change). Marsh type habitat switching affects fish, shellfish, and wildlife inhabitants, and can affect the regional ecosystem and economy. There are numerous restoration and revitalization projects underway in the coastal region, and their effects on the entire ecosystem need to be understood. For these reasons, monitoring persistent saltwater intrusion and inundation is important. For this study, persistent flooding in Louisiana coastal marshes was mapped using MODIS (Moderate Resolution Imaging Spectroradiometer) time series of a Normalized Difference Water Index (NDWI). The time series data were derived for 2000 through 2009, including flooding due to Hurricane Rita in 2005 and Hurricane Ike in 2008. Using the NDWI, duration and extent of flooding can be inferred. The Time Series Product Tool (TSPT), developed at NASA SSC, is a suite of software developed in MATLAB® that enables improved-quality time series images to be computed using advanced temporal processing techniques. This software has been used to compute time series for monitoring temporal changes in environmental phenomena, (e.g. NDVI times series from MODIS), and was modified and used to compute the NDWI indices and also the Normalized Difference Soil Index (NDSI). Coastwide Reference Monitoring System (CRMS) water levels from various hydrologic monitoring stations and aerial photography were used to optimize thresholds for MODIS-derived time series of NDWI and to validate resulting flood maps. In most of the profiles produced for post-hurricane assessment, the increase in the NDWI index (from storm surge) is accompanied by a decrease in the vegetation index (NDVI) and then a period of declining water. The NDSI index represents non-green or dead vegetation and increases after the hurricane's destruction of the marsh vegetation. Behavior of these indices over time is indicative of which areas remain flooded, which areas recover to their former levels of vegetative vigor, and which areas are stressed or in transition. Tracking these indices over time shows the recovery rate of vegetation and the relative behavior to inundation persistence. The results from this study demonstrated that identification of persistent marsh flooding, utilizing the tools developed in this study, provided an approximate 70-80 percent accuracy rate when compared to the actual days flooded at the CRMS stations.

A New Approach to Monitoring Coastal Marshes for Persistent Flooding

NASA Technical Reports Server (NTRS)

Kalcic, M. T.; Undersood, Lauren W.; Fletcher, Rose

2012-01-01

Many areas in coastal Louisiana are below sea level and protected from flooding by a system of natural and man-made levees. Flooding is common when the levees are overtopped by storm surge or rising rivers. Many levees in this region are further stressed by erosion and subsidence. The floodwaters can become constricted by levees and trapped, causing prolonged inundation. Vegetative communities in coastal regions, from fresh swamp forest to saline marsh, can be negatively affected by inundation and changes in salinity. As saltwater persists, it can have a toxic effect upon marsh vegetation causing die off and conversion to open water types, destroying valuable species habitats. The length of time the water persists and the average annual salinity are important variables in modeling habitat switching (cover type change). Marsh type habitat switching affects fish, shellfish, and wildlife inhabitants, and can affect the regional ecosystem and economy. There are numerous restoration and revitalization projects underway in the coastal region, and their effects on the entire ecosystem need to be understood. For these reasons, monitoring persistent saltwater intrusion and inundation is important. For this study, persistent flooding in Louisiana coastal marshes was mapped using MODIS (Moderate Resolution Imaging Spectroradiometer) time series of a Normalized Difference Water Index (NDWI). The time series data were derived for 2000 through 2009, including flooding due to Hurricane Rita in 2005 and Hurricane Ike in 2008. Using the NDWI, duration and extent of flooding can be inferred. The Time Series Product Tool (TSPT), developed at NASA SSC, is a suite of software developed in MATLAB(R) that enables improved-quality time series images to be computed using advanced temporal processing techniques. This software has been used to compute time series for monitoring temporal changes in environmental phenomena, (e.g. NDVI times series from MODIS), and was modified and used to compute the NDWI indices and also the Normalized Difference Soil Index (NDSI). Coastwide Reference Monitoring System (CRMS) water levels from various hydrologic monitoring stations and aerial photography were used to optimize thresholds for MODIS-derived time series of NDWI and to validate resulting flood maps. In most of the profiles produced for post-hurricane assessment, the increase in the NDWI index (from storm surge) is accompanied by a decrease in the vegetation index (NDVI) and then a period of declining water. The NDSI index represents non-green or dead vegetation and increases after the hurricane s destruction of the marsh vegetation. Behavior of these indices over time is indicative of which areas remain flooded, which areas recover to their former levels of vegetative vigor, and which areas are stressed or in transition. Tracking these indices over time shows the recovery rate of vegetation and the relative behavior to inundation persistence. The results from this study demonstrated that identification of persistent marsh flooding, utilizing the tools developed in this study, provided an approximate 70-80 percent accuracy rate when compared to the actual days flooded at the CRMS stations.

Probabilistic Mapping of Storm-induced Coastal Inundation for Climate Change Adaptation

NASA Astrophysics Data System (ADS)

Li, N.; Yamazaki, Y.; Roeber, V.; Cheung, K. F.; Chock, G.

2016-02-01

Global warming is posing an imminent threat to coastal communities worldwide. Under the IPCC RCP8.5 scenario, we utilize hurricane events downscaled from a CMIP5 global climate model using the stochastic-deterministic method of Emanuel (2013, Proc. Nat. Acad. Sci.) in a pilot study to develop an inundation map with projected sea-level rise for the urban Honolulu coast. The downscaling is performed for a 20-year period from 2081 to 2100 to capture the ENSO, which strongly influences the hurricane activity in the Pacific. A total of 50 simulations provide a quasi-stationary dataset of 1000 years for probabilistic analysis of the flood hazards toward the end of the century. We utilize the meta-model Hakou, which is based on precomputed hurricane scenarios using ADCIRC, SWAN, and a 1D Boussinesq model (Kennedy et al., 2012, Ocean Modelling), to estimate the annual maximum inundation along the project coastline at the present sea level. Screening of the preliminary results identifies the most severe three events for detailed inundation modeling using the package of Li et al. (2014, Ocean Modelling) at the projected sea level. For each event, the third generation spectral model WAVEWATCH III of Tolman (2008, Ocean Modelling) provides the hurricane waves and the circulation model NEOWAVE of Yamazaki et al. (2009, 2011, Int. J. Num. Meth. Fluids) computes the surge using a system of telescopic nested grids from the open ocean to the project coastline. The output defines the boundary conditions and initial still-water elevation for computation of phase-resolving surf-zone and inundation processes using the 2D Boussinesq model of Roeber and Cheung (2012, Coastal Engineering). Each computed inundation event corresponds to an annual maximum, and with 1000 years of data, has an occurrence probability of 0.1% in a given year. Barring the tail of the distribution, aggregation of the three computed events allow delineation of the inundation zone with annual exceedance probability equal to or greater than 0.2% (equivalent to a 500-year return period). An immediate application is to assess the inventory of buildings and structures in Honolulu that would be exposed to increased flood risks due to climate change and identify potential revisions to the building code as part of the adaptation process.

Tidal inundation (“Rob”) investigation using time series of high resolution satellite image data and from institu measurements along northern coast of Java (Pantura)

NASA Astrophysics Data System (ADS)

Andreas, Heri; Usriyah; Zainal Abidin, Hasanuddin; Anggreni Sarsito, Dina

2017-06-01

Tidal inundation (in Javanese they call it “Rob”) is now becoming a well known phenomenon along northern coast of Java Indonesia (Pantura). The occurrence of tidal inundation was recognized at least in the early 2000 and even earlier. In the recent years the tidal inundation comes not only at a high tide but even at the regular tide in some area across Pantura. In fact in location such as Pondok Bali, north of Blanakan, north of Pekalongan, north of Semarang and north west of Demak, seems those areas are sinking to the sea through times. Sea level rise and land subsidence are considered as main factors deriving the occurrence of this tidal inundation. We were using time series of high resolution satellite image data and insitu data measurements to mapping the tidal inundation along northern coast of Java. All available data from google data satellite archives (year 2000- recent years) and any available sources being analyze together with field surveys tagging and also from media information. As a result we can see the tidal inundation are taking place in Tanggerang, Jakarta, Bekasi, Cilamaya, Pondok Bali, Blanakan, Indramayu, Cirebon, Brebes, Tegal, Pemalang, Pekalongan, Kendal, Semarang, Demak, Gresik, Surabaya, Sidoarjo and Pasuruan.

Flood-inundation maps for the Driftwood River and Sugar Creek near Edinburgh, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.; Kim, Moon H.; Menke, Chad D.

2012-01-01

Digital flood-inundation maps for an 11.2 mile reach of the Driftwood River and a 5.2 mile reach of Sugar Creek, both near Edinburgh, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Camp Atterbury Joint Maneuver Training Center, Edinburgh, Indiana. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. Current conditions at the USGS streamgage in Indiana may be obtained on the Internet at http://waterdata.usgs.gov/in/nwis/current/?type=flow. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system at http://water.weather.gov/ahps/. The NWS forecasts flood hydrographs at many places that are often collocated at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. For this study, flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. The hydraulic model was then used to determine elevations throughout the study reaches for nine water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from bankfull to nearly the highest recorded water level at the USGS streamgage 03363000 Driftwood River near Edinburgh, Ind. The simulated water-surface profiles were then combined with a geospatial digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The availability of these maps along with real-time information available online regarding current stage from USGS streamgages and forecasted stream stages from the NWS provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post flood recovery efforts.

Flood-inundation maps for the East Fork White River at Columbus, Indiana

USGS Publications Warehouse

Lombard, Pamela J.

2013-01-01

Digital flood-inundation maps for a 5.4-mile reach of the East Fork White River at Columbus, Indiana, from where the Flatrock and Driftwood Rivers combine to make up East Fork White River to just upstream of the confluence of Clifty Creek with the East Fork White River, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at USGS streamgage 03364000, East Fork White River at Columbus, Indiana. Current conditions at the USGS streamgage may be obtained on the Internet from the USGS National Water Information System (http://waterdata.usgs.gov/in/nwis/uv/?site_no=03364000&agency_cd=USGS&). The National Weather Service (NWS) forecasts flood hydrographs for the East Fork White River at Columbus, Indiana at their Advanced Hydrologic Prediction Service (AHPS) flood warning system Website (http://water.weather.gov/ahps/), that may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at USGS streamgage 03364000, East Fork White River at Columbus, Indiana. The calibrated hydraulic model was then used to determine 15 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data), having a 0.37-ft vertical accuracy and a 1.02 ft horizontal accuracy), in order to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage at Columbus, Indiana, and forecasted stream stages from the NWS will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post-flood recovery efforts.

Flood profiles for lower Brooker Creek, west-central Florida

USGS Publications Warehouse

Murphy, W.R.

1978-01-01

Flood heights are computed for a range of recurrence intervals for a 12.6 mile reach of Brooker Creek, beginning at the mouth at Lake Tarpon. A Geological Survey step-backwater computer program, E431, was used in these analyses using: (1) Stream and valley cross-section geometry and roughness data; (2) Recurrence interval flood-peak discharges; (3) Recurrence interval starting elevations; (4) Gaging station stage-discharge relations. Flood heights may be plotted versus distance above stream mouth and connected to construct flood profiles. They may also be used to indicate areas of inundation on detailed topographic maps.

Computational Fluid Dynamic Analysis of Hydrodynamic forces on inundated bridge decks

NASA Astrophysics Data System (ADS)

Afzal, Bushra; Guo, Junke; Kerenyi, Kornel

2010-11-01

The hydraulic forces experienced by an inundated bridge deck have great importance in the design of bridges. Flood flows or hurricane add significant hydrodynamic loading on bridges, possibly resulting in failure of the bridge superstructures. The objective of the study is to establish validated computational practice to address research needs of the transportation community via computational fluid dynamic simulations. The reduced scale experiments conducted at Turner-Fairbank Highway Research Center establish the foundations of validated computational practices to address the research needs of the transportation community. Three bridge deck prototypes were used: a typical six-girder highway bridge deck, a three-girder deck, and a streamlined deck designed to better withstand the hydraulic forces. Results of the study showed that the streamlined deck significantly reduces drag, lift, and moment coefficient in comparison to the other bridge deck types. The CFD results matched the experimental data in terms of the relationship between inundation ratio and force measured at the bridge. The results of the present research will provide a tool for designing new bridges and retrofitting old ones.

Evaluation of Floodplain Modifications to Reduce the Effect of Floods Using a Two-Dimensional Hydrodynamic Model of the Flint River at Albany, Georgia

USGS Publications Warehouse

Musser, Jonathan W.

2008-01-01

Potential flow characteristics of future flooding along a 4.8-mile reach of the Flint River in Albany, Georgia, were simulated using recent digital-elevation-model data and the U.S. Geological Survey finite-element surface-water modeling system for two-dimensional flow in the horizontal plane (FESWMS-2DH). The model was run at four water-surface altitudes at the Flint River at Albany streamgage (02352500): 181.5-foot (ft) altitude with a flow of 61,100 cubic feet per second (ft3/s), 184.5-ft altitude with a flow of 75,400 ft3/s, 187.5-ft altitude with a flow of 91,700 ft3/s, and 192.5-ft altitude with a flow of 123,000 ft3/s. The model was run to measure changes in inundated areas and water-surface altitudes for eight scenarios of possible modifications to the 4.8-mile reach on the Flint River. The eight scenarios include removing a human-made peninsula located downstream from Oglethorpe Boulevard, increasing the opening under the Oakridge Drive bridge, adding culverts to the east Oakridge Drive bridge approach, adding culverts to the east and west Oakridge Drive bridge approaches, adding an overflow across the oxbow north of Oakridge Drive, making the overflow into a channel, removing the Oakridge Drive bridge, and adding a combination of an oxbow overflow and culverts on both Oakridge Drive bridge approaches. The modeled inundation and water-surface altitude changes were mapped for use in evaluating the river modifications. The most effective scenario at reducing inundated area was the combination scenario. At the 187.5-ft altitude, the inundated area decreased from 4.24 square miles to 4.00 square miles. The remove-peninsula scenario was the least effective with a reduction in inundated area of less than 0.01 square miles. In all scenarios, the inundated area reduction increased with water-surface altitude, peaking at the 187.5-ft altitude. The inundated area reduction then decreased at the gage altitude of 192.5 ft.

The effect of wave current interactions on the storm surge and inundation in Charleston Harbor during Hurricane Hugo 1989

NASA Astrophysics Data System (ADS)

Xie, Lian; Liu, Huiqing; Peng, Machuan

The effects of wave-current interactions on the storm surge and inundation induced by Hurricane Hugo in and around the Charleston Harbor and its adjacent coastal regions are examined by using a three-dimensional (3-D) wave-current coupled modeling system. The 3-D storm surge and inundation modeling component of the coupled system is based on the Princeton ocean model (POM), whereas the wave modeling component is based on the third-generation wave model, simulating waves nearshore (SWAN). The results indicate that the effects of wave-induced surface, bottom, and radiation stresses can separately or in combination produce significant changes in storm surge and inundation. The effects of waves vary spatially. In some areas, the contribution of waves to peak storm surge during Hurricane Hugo reached as high as 0.76 m which led to substantial changes in the inundation and drying areas simulated by the storm surge model.

Scenario-based projections of future urban inundation within a coupled hydrodynamic model framework: A case study in Dongguan City, China

NASA Astrophysics Data System (ADS)

Wu, Xushu; Wang, Zhaoli; Guo, Shenglian; Liao, Weilin; Zeng, Zhaoyang; Chen, Xiaohong

2017-04-01

One major threat to cities at present is the increased inundation hazards owing to changes in climate and accelerated human activity. Future evolution of urban inundation is still an unsolved issue, given large uncertainties in future environmental conditions within urbanized areas. Developing model techniques and urban inundation projections are essential for inundation management. In this paper, we proposed a 2D hydrodynamic inundation model by coupling SWMM and LISFLOOD-FP models, and revealed how future urban inundation would evolve for different storms, sea level rise and subsidence scenarios based on the developed model. The Shiqiao Creek District (SCD) in Dongguan City was used as the case study. The model ability was validated against the June 13th, 2008 inundation event, which occurred in SCD, and proved capable of simulating dynamic urban inundation. Scenario analyses revealed a high degree of consistency in the inundation patterns among different storms, with larger magnitudes corresponding to greater return periods. Inundations across SCD generally vary as a function of storm intensity, but for lowlands or regions without drainage facilities inundations tend to aggravate over time. In riverfronts, inundations would exacerbate with sea level rise or subsidence; however, the inland inundations are seemingly insensitive to both factors. For the combined scenario of 100-yr storm, 0.5 m subsidence and 0.7 m sea level rise, the riverside inundations would occur much in advance, whilst catastrophic inundations sweep across SCD. Furthermore, the optimal low-impact development found for this case study includes 0.2 km2 of permeable pavements, 0.1 km2 of rain barrels and 0.7 km2 of green roofs.

Simulation of Rio Grande floodplain inundation Using FLO-2D

Treesearch

J. S. O' Brien; W. T. Fullerton

1999-01-01

Spring floodplain inundation is important to the natural functions of the Rio Grande bosque biological community including cottonwood tree germination and recruitment. To predict floodplain inundation, a two-dimensional flood routing model FLO-2D will be applied to various reaches of the Rio Grande. FLO-2D will assess overbank flooding in terms of the area of...

Flood-inundation maps for Sweetwater Creek from above the confluence of Powder Springs Creek to the Interstate 20 bridge, Cobb and Douglas Counties, Georgia

USGS Publications Warehouse

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 10.5-mile reach of Sweetwater Creek, from about 1,800 feet above the confluence of Powder Springs Creek to about 160 feet below the Interstate 20 bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with Cobb County, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Sweetwater Creek near Austell, Georgia (02337000). Current stage at this USGS streamgage may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Sweetwater Creek near Austell (02337000), which is available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers Hydrologic Engineering Centers River Analysis System (HEC–RAS) software for Sweetwater Creek and was used to compute flood profiles for a 10.5-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Sweetwater Creek near Austell streamgage (02337000), as well as high-water marks collected during annual peak-flow events in 1982 and 2009. The hydraulic model was then used to determine 21 water-surface profiles for flood stages at the Sweetwater Creek streamgage at 1-foot intervals referenced to the streamgage datum and ranging from just above bankfull stage (12.0 feet) to approximately 1.2 feet above the highest recorded water level at the streamgage (32.0 feet). The simulated water-surface profiles were then combined with a geographic information system digital elevation model—derived from contour data (8-foot horizontal resolution), in Cobb County, and USGS National Elevation Dataset (31-foot horizontal resolution), in Douglas County—to delineate the area flooded for each 1-foot increment of stream stage. The availability of these maps, when combined with real-time information regarding current stage from USGS streamgages and forecasted stream stages from the NWS, provides emergency management personnel and residents with critical information during flood-response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Can Atmospheric Reanalysis Data Sets Be Used to Reproduce Flooding Over Large Scales?

NASA Astrophysics Data System (ADS)

Andreadis, Konstantinos M.; Schumann, Guy J.-P.; Stampoulis, Dimitrios; Bates, Paul D.; Brakenridge, G. Robert; Kettner, Albert J.

2017-10-01

Floods are costly to global economies and can be exceptionally lethal. The ability to produce consistent flood hazard maps over large areas could provide a significant contribution to reducing such losses, as the lack of knowledge concerning flood risk is a major factor in the transformation of river floods into flood disasters. In order to accurately reproduce flooding in river channels and floodplains, high spatial resolution hydrodynamic models are needed. Despite being computationally expensive, recent advances have made their continental to global implementation feasible, although inputs for long-term simulations may require the use of reanalysis meteorological products especially in data-poor regions. We employ a coupled hydrologic/hydrodynamic model cascade forced by the 20CRv2 reanalysis data set and evaluate its ability to reproduce flood inundation area and volume for Australia during the 1973-2012 period. Ensemble simulations using the reanalysis data were performed to account for uncertainty in the meteorology and compared with a validated benchmark simulation. Results show that the reanalysis ensemble capture the inundated areas and volumes relatively well, with correlations for the ensemble mean of 0.82 and 0.85 for area and volume, respectively, although the meteorological ensemble spread propagates in large uncertainty of the simulated flood characteristics.

Flood-inundation maps for the Big Blue River at Shelbyville, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2017-02-13

Digital flood-inundation maps for a 4.1-mile reach of the Big Blue River at Shelbyville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The floodinundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at https://water. usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Big Blue River at Shelbyville, Ind. (station number 03361500). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata. usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at https://water.weather.gov/ ahps/, which also forecasts flood hydrographs at this site (SBVI3). Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at the Big Blue River at Shelbyville, Ind., streamgage. The calibrated hydraulic model was then used to compute 12 water-surface profiles for flood stages referenced to the streamgage datum and ranging from 9.0 feet, or near bankfull, to 19.4 feet, the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging [lidar] data having a 0.98-foot vertical accuracy and 4.9-foot horizontal resolution) to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage at the Big Blue River at Shelbyville, Ind., and forecasted stream stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post-flood recovery efforts.

Modeling and simulation of storm surge on Staten Island to understand inundation mitigation strategies

USGS Publications Warehouse

Kress, Michael E.; Benimoff, Alan I.; Fritz, William J.; Thatcher, Cindy A.; Blanton, Brian O.; Dzedzits, Eugene

2016-01-01

Hurricane Sandy made landfall on October 29, 2012, near Brigantine, New Jersey, and had a transformative impact on Staten Island and the New York Metropolitan area. Of the 43 New York City fatalities, 23 occurred on Staten Island. The borough, with a population of approximately 500,000, experienced some of the most devastating impacts of the storm. Since Hurricane Sandy, protective dunes have been constructed on the southeast shore of Staten Island. ADCIRC+SWAN model simulations run on The City University of New York's Cray XE6M, housed at the College of Staten Island, using updated topographic data show that the coast of Staten Island is still susceptible to tidal surge similar to those generated by Hurricane Sandy. Sandy hindcast simulations of storm surges focusing on Staten Island are in good agreement with observed storm tide measurements. Model results calculated from fine-scaled and coarse-scaled computational grids demonstrate that finer grids better resolve small differences in the topography of critical hydraulic control structures, which affect storm surge inundation levels. The storm surge simulations, based on post-storm topography obtained from high-resolution lidar, provide much-needed information to understand Staten Island's changing vulnerability to storm surge inundation. The results of fine-scale storm surge simulations can be used to inform efforts to improve resiliency to future storms. For example, protective barriers contain planned gaps in the dunes to provide for beach access that may inadvertently increase the vulnerability of the area.

The Shoreline Management Tool - an ArcMap tool for analyzing water depth, inundated area, volume, and selected habitats, with an example for the lower Wood River Valley, Oregon

USGS Publications Warehouse

Snyder, Daniel T.; Haluska, Tana L.; Respini-Irwin, Darius

2013-01-01

The Shoreline Management Tool is a geographic information system (GIS) based program developed to assist water- and land-resource managers in assessing the benefits and effects of changes in surface-water stage on water depth, inundated area, and water volume. Additionally, the Shoreline Management Tool can be used to identify aquatic or terrestrial habitat areas where conditions may be suitable for specific plants or animals as defined by user-specified criteria including water depth, land-surface slope, and land-surface aspect. The tool can also be used to delineate areas for use in determining a variety of hydrologic budget components such as surface-water storage, precipitation, runoff, or evapotranspiration. The Shoreline Management Tool consists of two parts, a graphical user interface for use with Esri™ ArcMap™ GIS software to interact with the user to define scenarios and map results, and a spreadsheet in Microsoft® Excel® developed to display tables and graphs of the results. The graphical user interface allows the user to define a scenario consisting of an inundation level (stage), land areas (parcels), and habitats (areas meeting user-specified conditions) based on water depth, slope, and aspect criteria. The tool uses data consisting of land-surface elevation, tables of stage/volume and stage/area, and delineated parcel boundaries to produce maps (data layers) of inundated areas and areas that meet the habitat criteria. The tool can be run in a Single-Time Scenario mode or in a Time-Series Scenario mode, which uses an input file of dates and associated stages. The spreadsheet part of the tool uses a macro to process the results from the graphical user interface to create tables and graphs of inundated water volume, inundated area, dry area, and mean water depth for each land parcel based on the user-specified stage. The macro also creates tables and graphs of the area, perimeter, and number of polygons comprising the user-specified habitat areas within each parcel. The Shoreline Management Tool is highly transferable, using easily generated or readily available data. The capabilities of the tool are demonstrated using data from the lower Wood River Valley adjacent to Upper Klamath and Agency Lakes in southern Oregon.

Potential Inundation due to Rising Sea Levels in the San Francisco Bay Region

USGS Publications Warehouse

Knowles, Noah

2009-01-01

An increase in the rate of sea level rise is one of the primary impacts of projected global climate change. To assess potential inundation associated with a continued acceleration of sea level rise, the highest resolution elevation data available were assembled from various sources and mosaicked to cover the land surfaces of the San Francisco Bay region. Next, to quantify high water levels throughout the bay, a hydrodynamic model of the San Francisco Estuary was driven by a projection of hourly water levels at the Presidio. This projection was based on a combination of climate model outputs and empirical models and incorporates astronomical, storm surge, El Niño, and long-term sea level rise influences. Based on the resulting data, maps of areas vulnerable to inundation were produced, corresponding to specific amounts of sea level rise and recurrence intervals. These maps portray areas where inundation will likely be an increasing concern. In the North Bay, wetland survival and developed fill areas are at risk. In Central and South bays, a key feature is the bay-ward periphery of developed areas that would be newly vulnerable to inundation. Nearly all municipalities adjacent to South Bay face this risk to some degree. For the Bay as a whole, as early as 2050 under this scenario, the one-year peak event nearly equals the 100-year peak event in 2000. Maps of vulnerable areas are presented and some implications discussed.

A Spatially Based Area–Time Inundation Index Model Developed to Assess Habitat Opportunity in Tidal–Fluvial Wetlands and Restoration Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, Andre M.; Diefenderfer, Heida L.; Ward, Duane L.

The hydrodynamics of tidal wetland areas in the lower Columbia River floodplain and estuary directly affect habitat opportunity for endangered salmonid fishes. Physical and biological structures and functions in the system are directly affected by inundation patterns influenced by tidal cycles, hydropower operations, river discharge, upriver water withdrawals, climate, and physical barriers such as dikes, culverts, and tide gates. Ongoing ecosystem restoration efforts are intended to increase the opportunity for salmon to access beneficial habitats by hydrologically reconnecting main-stem river channels and diked areas within the historical floodplain. To address the need to evaluate habitat opportunity, a geographic information system-basedmore » Area-Time Inundation Index Model (ATIIM) was developed. The ATIIM integrates in situ or modeled hourly water-surface elevation (WSE) data and advanced terrain processing of high-resolution elevation data. The ATIIM uses a spatially based wetted-area algorithm to determine site average bankfull elevation, two- and three-dimensional inundation extent, and other site metrics. Hydrological process metrics such as inundation frequency, duration, maximum area, and maximum frequency area can inform evaluation of proposed restoration sites; e.g., determine trade-offs between WSE and habitat opportunity, contrast alternative restoration designs, predict impacts of altered flow regimes, and estimate nutrient and biomass fluxes. In an adaptive management framework, this model can be used to provide standardized site comparisons and effectiveness monitoring of changes in the developmental trajectories of restoration sites. Results are presented for 11 wetlands representative of tidal marshes, tidal forested wetlands, and restoration sites.« less

Elevation-Based Sea-Level Rise Vulnerability Assessment of Mindanao, Philippines: are Freely-Available 30-M Dems Good Enough?

NASA Astrophysics Data System (ADS)

Santillan, J. R.; Makinano-Santillan, M.

2017-09-01

We assessed the vertical accuracies and uncertainties of three freely-available global DEMs as inputs to elevation-based sea-level rise vulnerability assessment of Mindanao, Philippines - an area where above average SLR of 14.7 mm/year was recently found. These DEMs are the Shuttle Radar Topography Mission (SRTM) DEM, ASTER Global DEM (GDEM Version 2), and ALOS World 3D-30 (AW3D30). Using 2,076 ground control points, we computed each DEM's vertical accuracies and uncertainties, and from these we determined the smallest increment of sea-level rise (SLRImin) that should be considered when using the DEMs for SLR impact assessment, as well as the Minimum Planning Timeline (TLmin) for an elevation-based SLR assessment. Results of vertical accuracy assessment revealed Root Mean Square Errors of 9.80 m for ASTER GDEM V2, 5.16 m for SRTM DEM, and 4.32 m for AW3D30. Vertical uncertainties in terms of the Linear Error at 95 % Confidence (LE95) were found to be as follows: 19.21 m for ASTER GDEM V2, 10.12 m for SRTM DEM, and 8.47 m for AW3D30. From these, we found that ASTER GDEM2 is suitable to model SLR increments of at least 38.41 m and it will take 2,613 years for the cumulative water level increase of 14.7 mm/year to reach the minimum SLR increment afforded by this DEM. For the SRTM DEM, SLRImin and TLmin were computed as 20.24 m and 1,377 years, respectively. For the AW3D30, SLRImin and TLmin were computed as 16.92 m and 1,151 years, respectively. These results suggest that the readily available global DEMs' suitability for mapping coastal inundations due to SLR in our study area is limited by their low vertical accuracies and high uncertainties. All the three DEMs do not have the necessary accuracy and minimum uncertainties that will make them suitable for mapping inundations of Mindanao at smaller increments of SLR (e.g., SLR ≤ 5 m). Hence, users who apply any of these DEMs for SLR impact assessment at SLRIs lower than the DEM's SLRImin must be cautious in reporting the areas of SLR vulnerable zones. Reporting the inundated areas as a range instead of a singular value for a given SLR scenario can highlight the inherent accuracy and uncertainty of the DEM used in the assessment.

Variations in City Exposure and Sensitivity to Tsunami Hazards in Oregon

USGS Publications Warehouse

Wood, Nathan

2007-01-01

Evidence of past events and modeling of potential future events suggest that tsunamis are significant threats to Oregon coastal communities. Although a potential tsunami-inundation zone from a Cascadia Subduction Zone earthquake has been delineated, what is in this area and how communities have chosen to develop within it have not been documented. A vulnerability assessment using geographic-information-system tools was conducted to describe tsunami-prone landscapes on the Oregon coast and to document city variations in developed land, human populations, economic assets, and critical facilities relative to the tsunami-inundation zone. Results indicate that the Oregon tsunami-inundation zone contains approximately 22,201 residents (four percent of the total population in the seven coastal counties), 14,857 employees (six percent of the total labor force), and 53,714 day-use visitors on average every day to coastal Oregon State Parks within the tsunami-inundation zone. The tsunami-inundation zone also contains 1,829 businesses that generate approximately $1.9 billion in annual sales volume (seven and five percent of study-area totals, respectively) and tax parcels with a combined total value of $8.2 billion (12 percent of the study-area total). Although occupancy values are not known for each facility, the tsunami-inundation zone also contains numerous dependent-population facilities (for example, adult-residential-care facilities, child-day-care facilities, and schools), public venues (for example, religious organizations and libraries), and critical facilities (for example, police stations). Racial diversity of residents in the tsunami-inundation zone is low, with 96 percent identifying themselves as White, either alone or in combination with one or more race. Twenty-two percent of the residents in the tsunami-inundation zone are over 65 years in age, 36 percent of the residents live on unincorporated county lands, and 37 percent of the households are renter occupied. The employee population in the tsunami-inundation zone is largely in accommodation and food services, retail trade, manufacturing, and arts and entertainment sectors. Results indicate that vulnerability, described here by exposure (the amount of assets in tsunami-prone areas) and sensitivity (the relative percentage of assets in tsunami-prone areas) varies considerably among 26 incorporated cities in Oregon. City exposure and sensitivity to tsunami hazards is highest in the northern portion of the coast. The City of Seaside in Clatsop County has the highest exposure, the highest sensitivity, and the highest combined relative exposure and sensitivity to tsunamis. Results also indicate that the amount of city assets in tsunami-prone areas is weakly related to the amount of a community's land in this zone; the percentage of a city's assets, however, is strongly related to the percentage of its land that is in the tsunami-prone areas. This report will further the dialogue on societal risk to tsunami hazards in Oregon and help identify future preparedness, mitigation, response, and recovery planning needs within coastal cities and economic sectors of the state of Oregon.

Rapid inundation estimates at harbor scale using tsunami wave heights offshore simulation and coastal amplification laws

NASA Astrophysics Data System (ADS)

Gailler, A.; Loevenbruck, A.; Hebert, H.

2013-12-01

Numerical tsunami propagation and inundation models are well developed and have now reached an impressive level of accuracy, especially in locations such as harbors where the tsunami waves are mostly amplified. In the framework of tsunami warning under real-time operational conditions, the main obstacle for the routine use of such numerical simulations remains the slowness of the numerical computation, which is strengthened when detailed grids are required for the precise modeling of the coastline response of an individual harbor. Thus only tsunami offshore propagation modeling tools using a single sparse bathymetric computation grid are presently included within the French Tsunami Warning Center (CENALT), providing rapid estimation of tsunami warning at western Mediterranean and NE Atlantic basins scale. We present here a preliminary work that performs quick estimates of the inundation at individual harbors from these high sea forecasting tsunami simulations. The method involves an empirical correction based on theoretical amplification laws (either Green's or Synolakis laws). The main limitation is that its application to a given coastal area would require a large database of previous observations, in order to define the empirical parameters of the correction equation. As no such data (i.e., historical tide gage records of significant tsunamis) are available for the western Mediterranean and NE Atlantic basins, we use a set of synthetic mareograms, calculated for both fake and well-known historical tsunamigenic earthquakes in the area. This synthetic dataset is obtained through accurate numerical tsunami propagation and inundation modeling by using several nested bathymetric grids of increasingly fine resolution close to the shores (down to a grid cell size of 3m in some Mediterranean harbors). Non linear shallow water tsunami modeling performed on a single 2' coarse bathymetric grid are compared to the values given by time-consuming nested grids simulations (and observation when available), in order to check to which extent the simple approach based on the amplification laws can explain the data. The idea is to fit tsunami data with numerical modeling carried out without any refined coastal bathymetry/topography. To this end several parameters are discussed, namely the bathymetric depth to which model results must be extrapolated (using the Green's law), or the mean bathymetric slope to consider near the studied coast (when using the Synolakis law).

Rapid inundation estimates using coastal amplification laws in the western Mediterranean basin

NASA Astrophysics Data System (ADS)

Gailler, Audrey; Loevenbruck, Anne; Hébert, Hélène

2014-05-01

Numerical tsunami propagation and inundation models are well developed and have now reached an impressive level of accuracy, especially in locations such as harbors where the tsunami waves are mostly amplified. In the framework of tsunami warning under real-time operational conditions, the main obstacle for the routine use of such numerical simulations remains the slowness of the numerical computation, which is strengthened when detailed grids are required for the precise modeling of the coastline response of an individual harbor. Thus only tsunami offshore propagation modeling tools using a single sparse bathymetric computation grid are presently included within the French Tsunami Warning Center (CENALT), providing rapid estimation of tsunami warning at western Mediterranean and NE Atlantic basins scale. We present here a preliminary work that performs quick estimates of the inundation at individual harbors from these high sea forecasting tsunami simulations. The method involves an empirical correction based on theoretical amplification laws (either Green's or Synolakis laws). The main limitation is that its application to a given coastal area would require a large database of previous observations, in order to define the empirical parameters of the correction equation. As no such data (i.e., historical tide gage records of significant tsunamis) are available for the western Mediterranean and NE Atlantic basins, we use a set of synthetic mareograms, calculated for both fake events and well-known historical tsunamigenic earthquakes in the area. This synthetic dataset is obtained through accurate numerical tsunami propagation and inundation modeling by using several nested bathymetric grids of increasingly fine resolution close to the shores (down to a grid cell size of 3m in some Mediterranean harbors). Non linear shallow water tsunami modeling performed on a single 2' coarse bathymetric grid are compared to the values given by time-consuming nested grids simulations (and observation when available), in order to check to which extent the simple approach based on the amplification laws can explain the data. The idea is to fit tsunami data with numerical modeling carried out without any refined coastal bathymetry/topography. To this end several parameters are discussed, namely the bathymetric depth to which model results must be extrapolated (using the Green's law), or the mean bathymetric slope to consider near the studied coast (when using the Synolakis law).

Estimation of Damaged Areas due to the 2010 Chile Earthquake and Tsunami Using SAR Imagery of Alos/palsar

NASA Astrophysics Data System (ADS)

Made, Pertiwi Jaya Ni; Miura, Fusanori; Besse Rimba, A.

2016-06-01

A large-scale earthquake and tsunami affect thousands of people and cause serious damages worldwide every year. Quick observation of the disaster damage is extremely important for planning effective rescue operations. In the past, acquiring damage information was limited to only field surveys or using aerial photographs. In the last decade, space-borne images were used in many disaster researches, such as tsunami damage detection. In this study, SAR data of ALOS/PALSAR satellite images were used to estimate tsunami damage in the form of inundation areas in Talcahuano, the area near the epicentre of the 2010 Chile earthquake. The image processing consisted of three stages, i.e. pre-processing, analysis processing, and post-processing. It was conducted using multi-temporal images before and after the disaster. In the analysis processing, inundation areas were extracted through the masking processing. It consisted of water masking using a high-resolution optical image of ALOS/AVNIR-2 and elevation masking which built upon the inundation height using DEM image of ASTER-GDEM. The area result was 8.77 Km2. It showed a good result and corresponded to the inundation map of Talcahuano. Future study in another area is needed in order to strengthen the estimation processing method.

Hurricanes Harvey and Irma - High-Resolution Flood Mapping and Monitoring from Sentinel SAR with the Depolarization Reduction Algorithm for Global Observations of InundatioN (DRAGON)

NASA Astrophysics Data System (ADS)

Nghiem, S. V.; Brakenridge, G. R.; Nguyen, D. T.

2017-12-01

Hurricane Harvey inflicted historical catastrophic flooding across extensive regions around Houston and southeast Texas after making landfall on 25 August 2017. The Federal Emergency Management Agency (FEMA) requested urgent supports for flood mapping and monitoring in an emergency response to the extreme flood situation. An innovative satellite remote sensing method, called the Depolarization Reduction Algorithm for Global Observations of inundatioN (DRAGON), has been developed and implemented for use with Sentinel synthetic aperture radar (SAR) satellite data at a resolution of 10 meters to identify, map, and monitor inundation including pre-existing water bodies and newly flooded areas. Results from this new method are hydrologically consistent and have been verified with known surface waters (e.g., coastal ocean, rivers, lakes, reservoirs, etc.), with clear-sky high-resolution WorldView images (where waves can be seen on surface water in inundated areas within a small spatial coverage), and with other flood maps from the consortium of Global Flood Partnership derived from multiple satellite datasets (including clear-sky Landsat and MODIS at lower resolutions). Figure 1 is a high-resolution (4K UHD) image of a composite inundation map for the region around Rosharon (in Brazoria County, south of Houston, Texas). This composite inundation map reveals extensive flooding on 29 August 2017 (four days after Hurricane Harvey made landfall), and the inundation was still persistent in most of the west and south of Rosharon one week later (5 September 2017) while flooding was reduced in the east of Rosharon. Hurricane Irma brought flooding to a number of areas in Florida. As of 10 September 2017, Sentinel SAR flood maps reveal inundation in the Florida Panhandle and over lowland surfaces on several islands in the Florida Keys. However, Sentinel SAR results indicate that flooding along the Florida coast was not extreme despite Irma was a Category-5 hurricane that might have inflicted a potentially strong storm surge. DRAGON flood mapping products over various regions in Texas and in Florida were provided to FEMA. Figure 1. Composite inundation map derived from Sentinel SAR data for the region around Rosharon on 9/5/2017 (orange), inundation on 8/29/2017 (yellow), and pre-existing surface waters on 8/5/2017 (blue).

Application of a distributed hydrological model to the design of a road inundation warning system for flash flood prone areas

NASA Astrophysics Data System (ADS)

Versini, P.-A.; Gaume, E.; Andrieu, H.

2010-04-01

This paper presents an initial prototype of a distributed hydrological model used to map possible road inundations in a region frequently exposed to severe flash floods: the Gard region (South of France). The prototype has been tested in a pseudo real-time mode on five recent flash flood events for which actual road inundations have been inventoried. The results are promising: close to 100% probability of detection of actual inundations, inundations detected before they were reported by the road management field teams with a false alarm ratios not exceeding 30%. This specific case study differs from the standard applications of rainfall-runoff models to produce flood forecasts, focussed on a single or a limited number of gauged river cross sections. It illustrates that, despite their lack of accuracy, hydro-meteorological forecasts based on rainfall-runoff models, especially distributed models, contain valuable information for flood event management. The possible consequences of landslides, debris flows and local erosion processes, sometimes associated with flash floods, were not considered at this stage of development of the prototype. They are limited in the Gard region but should be taken into account in future developments of the approach to implement it efficiently in other areas more exposed to these phenomena such as the Alpine area.

Comparison between flood prone areas' geomorphic features in the Abruzzo region

NASA Astrophysics Data System (ADS)

Orlando, D.; Giglioni, M.; Magnaldi, S.

2017-07-01

Flood risk maps are one of the main non-structural measures for risk mitigation, but, as the risk knowledge degree is directly proportional to the community interest and financial capability, many sites are devoid of flood inundation areas studies. Recently many authors have investigated the capability of flood prone areas individuation with geomorphological DIGITAL ELEVATION MODEL(DEM) based approaches. These approaches highlight the role of geomorphic features derived from DEM, in this case slope, curvature, elevation, and topographic wetness index, to preliminary inundated areas' identification, without using hydraulic simulations. The present studies aim to analyze the geomorphic features of different hazard levels that lie under the identified inundated areas that have been carried out by the Abruzzo Region Basin Authority. The Aterno-Pescara and Foro river basins have been investigated. The results show that the characteristics of the flooded areas can be clearly distinguished from those of the entire basin,however, the difficultly of geomorphic features in individuatingthe areas of different hazard classifications is obvious.

Rapid inundation estimates at harbor scale using tsunami wave heights offshore simulation and Green's law approach

NASA Astrophysics Data System (ADS)

Gailler, Audrey; Hébert, Hélène; Loevenbruck, Anne

2013-04-01

Improvements in the availability of sea-level observations and advances in numerical modeling techniques are increasing the potential for tsunami warnings to be based on numerical model forecasts. Numerical tsunami propagation and inundation models are well developed and have now reached an impressive level of accuracy, especially in locations such as harbors where the tsunami waves are mostly amplified. In the framework of tsunami warning under real-time operational conditions, the main obstacle for the routine use of such numerical simulations remains the slowness of the numerical computation, which is strengthened when detailed grids are required for the precise modeling of the coastline response on the scale of an individual harbor. In fact, when facing the problem of the interaction of the tsunami wavefield with a shoreline, any numerical simulation must be performed over an increasingly fine grid, which in turn mandates a reduced time step, and the use of a fully non-linear code. Such calculations become then prohibitively time-consuming, which is clearly unacceptable in the framework of real-time warning. Thus only tsunami offshore propagation modeling tools using a single sparse bathymetric computation grid are presently included within the French Tsunami Warning Center (CENALT), providing rapid estimation of tsunami wave heights in high seas, and tsunami warning maps at western Mediterranean and NE Atlantic basins scale. We present here a preliminary work that performs quick estimates of the inundation at individual harbors from these deep wave heights simulations. The method involves an empirical correction relation derived from Green's law, expressing conservation of wave energy flux to extend the gridded wave field into the harbor with respect to the nearby deep-water grid node. The main limitation of this method is that its application to a given coastal area would require a large database of previous observations, in order to define the empirical parameters of the correction equation. As no such data (i.e., historical tide gage records of significant tsunamis) are available for the western Mediterranean and NE Atlantic basins, a set of synthetic mareograms is calculated for both fake and well-known historical tsunamigenic earthquakes in the area. This synthetic dataset is obtained through accurate numerical tsunami propagation and inundation modeling by using several nested bathymetric grids characterized by a coarse resolution over deep water regions and an increasingly fine resolution close to the shores (down to a grid cell size of 3m in some Mediterranean harbors). This synthetic dataset is then used to approximate the empirical parameters of the correction equation. Results of inundation estimates in several french Mediterranean harbors obtained with the fast "Green's law - derived" method are presented and compared with values given by time-consuming nested grids simulations.

Analysis of floods, including the tropical storm Irene inundation, of the Ottauquechee River in Woodstock, Bridgewater, and Killington and of Reservoir Brook in Bridgewater and Plymouth, Vermont

USGS Publications Warehouse

Flynn, Robert H.

2014-01-01

In addition to the two digital flood inundation maps, flood profiles were created that depict the study reach flood elevation of tropical storm Irene of August 2011 and the 10-, 2-, 1-, and 0.2-percent AEP floods, also known as the 10-, 50-, 100-, and 500-year floods, respectively. The 10-, 2-, 1-, and 0.2-percent AEP flood discharges were determined using annual peak flow data from the USGS Ottauquechee River near West Bridgewater, Vt. streamgage (station 01150900). Flood profiles were computed for the Ottauquechee River and Reservoir Brook by means of a one-dimensional step-backwater model. The model was calibrated using documented high-water marks of the peak of the tropical storm Irene flood of August 2011 as well as stage discharge data as determined for USGS Ottauquechee River near West Bridgewater, Vt. streamgage (station 01150900). The simulated water-surface profiles were combined with a digital elevation model within a geographic information system to delineate the areas flooded during tropical storm Irene and for the 1-percent AEP water-surface profile. The digital elevation model data were derived from light detection and ranging (lidar) data obtained for a 3,281-foot (1,000-meter) corridor along the Ottauquechee River study reach and were augmented with 33-foot (10- meter) contour interval data in the modeled flood-inundation areas outside the lidar corridor. The 33-foot (10-meter) contour interval USGS 15-minute quadrangle topographic digital raster graphics map used to augment lidar data was produced at a scale of 1:24,000. The digital flood inundation maps and flood profiles along with information regarding current stage from USGS streamgages on the Internet provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for Cedar Creek at 18th Street at Auburn, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2018-02-27

Digital flood-inundation maps for a 1.9-mile reach of Cedar Creek at Auburn, Indiana (Ind.), from the First Street bridge, downstream to the streamgage at 18th Street, then ending approximately 1,100 feet (ft) downstream of the Baltimore and Ohio railroad, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on Cedar Creek at 18th Street at Auburn, Ind. (station number 04179520). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, although forecasts of flood hydrographs are not available at this site (ABBI3).Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relation at the Cedar Creek at 18th Street at Auburn, Ind. streamgage and the documented high-water marks from the flood of March 11, 2009. The calibrated hydraulic model was then used to compute seven water-surface profiles for flood stages referenced to the streamgage datum and ranging from 7 ft, or near bankfull, to 13 ft, in 1-foot increments. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging [lidar] data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each water level.The availability of these maps, along with internet information regarding current stage from the USGS streamgage at Cedar Creek at 18th Street at Auburn, Ind., and stream information from the National Weather Service, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for postflood recovery efforts.

Flood-inundation maps for the White River at Noblesville, Indiana

USGS Publications Warehouse

Martin, Zachary W.

2017-11-02

Digital flood-inundation maps for a 7.5-mile reach of the White River at Noblesville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the White River at Noblesville, Ind., streamgage (USGS station number 03349000). Real-time stages at this streamgage may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at the same site as the USGS streamgage (NWS site NBLI3).Flood profiles were computed for the stream reach by means of a one-dimensional, step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current (2016) stage-discharge rating at the USGS streamgage 03349000, White River at Noblesville, Ind., and documented high-water marks from the floods of September 4, 2003, and May 6, 2017. The hydraulic model was then used to compute 15 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum ranging from 10.0 ft (the NWS “action stage”) to 24.0 ft, which is the highest stage interval of the current (2016) USGS stage-discharge rating curve and 2 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability of these maps, along with internet information regarding current stage from the USGS streamgage and forecasted high-flow stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, as well as for postflood recovery efforts.

Flood inundation maps for the Wabash River at New Harmony, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.

2016-10-11

Digital flood-inundation maps for a 3.68-mile reach of the Wabash River extending 1.77 miles upstream and 1.91 miles downstream from streamgage 03378500 at New Harmony, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Wabash River at New Harmony, Ind. (station 03378500). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NHRI3).Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at the Wabash River at New Harmony, Ind., streamgage and the documented high-water marks from the flood of April 27–28, 2013. The calibrated hydraulic model was then used to compute 17 water-surface profiles for flood stages at approximately 1-foot intervals referenced to the streamgage datum and ranging from 10.0 feet, or near bankfull, to 25.4 feet, the highest stage of the stage-discharge rating curve used in the model. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging (lidar) data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) to delineate the area flooded at each water level.The availability of these maps along with Internet information regarding current stage from the USGS streamgage at Wabash River at New Harmony, Ind., and forecasted stream stages from the NWS will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the St. Joseph River at Elkhart, Indiana

USGS Publications Warehouse

Martin, Zachary W.

2017-02-01

Digital flood-inundation maps for a 6.6-mile reach of the St. Joseph River at Elkhart, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 04101000, St. Joseph River at Elkhart, Ind. Real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at https://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS site EKMI3).Flood profiles were computed for the stream reach by means of a one-dimensional, step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current stage-discharge rating at the USGS streamgage 04101000, St. Joseph River at Elkhart, Ind., and the documented high-water marks from the flood of March 1982. The hydraulic model was then used to compute six water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum ranging from 23.0 ft (the NWS “action stage”) to 28.0 ft, which is the highest stage interval of the current USGS stage-discharge rating curve and 1 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging [lidar] data having a 0.49-ft root mean squared error and 4.9-ft horizontal resolution, resampled to a 10-ft grid) to delineate the area flooded at each stage.The availability of these maps, along with Internet information regarding current stage from the USGS streamgage and forecasted high-flow stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-Inundation Maps for Sugar Creek at Crawfordsville, Indiana

USGS Publications Warehouse

Martin, Zachary W.

2016-06-06

Digital flood-inundation maps for a 6.5-mile reach of Sugar Creek at Crawfordsville, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind. Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (NWS site CRWI3).Flood profiles were computed for the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind., reach by means of a one-dimensional step-backwater hydraulic modeling software developed by the U.S. Army Corps of Engineers. The hydraulic model was calibrated using the current stage-discharge rating at the USGS streamgage 03339500, Sugar Creek at Crawfordsville, Ind., and high-water marks from the flood of April 19, 2013, which reached a stage of 15.3 feet. The hydraulic model was then used to compute 13 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum ranging from 4.0 ft (the NWS “action stage”) to 16.0 ft, which is the highest stage interval of the current USGS stage-discharge rating curve and 2 ft higher than the NWS “major flood stage.” The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging [lidar]) data having a 0.49-ft root mean squared error and 4.9-ft horizontal resolution) to delineate the area flooded at each stage.The availability of these maps, along with Internet information regarding current stage from the USGS streamgage and forecasted high-flow stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Flood-inundation maps for the Mississinewa River at Marion, Indiana, 2013

USGS Publications Warehouse

Coon, William F.

2014-01-01

Digital flood-inundation maps for a 9-mile (mi) reach of the Mississinewa River from 0.75 mi upstream from the Pennsylvania Street bridge in Marion, Indiana, to 0.2 mi downstream from State Route 15 were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The flood inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Mississinewa River at Marion (station number 03326500). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the current stage-discharge relation at the Mississinewa River streamgage, in combination with water-surface profiles from historic floods and from the current (2002) flood-insurance study for Grant County, Indiana. The hydraulic model was then used to compute seven water-surface profiles for flood stages at 1-fo (ft) intervals referenced to the streamgage datum and ranging from 10 ft, which is near bankfull, to 16 ft, which is between the water levels associated with the estimated 10- and 2-percent annual exceedance probability floods (floods with recurrence interval between 10 and 50 years) and equals the “major flood stage” as defined by the NWS. The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model (derived from light detection and ranging (lidar) data having a 0.98 ft vertical accuracy and 4.9 ft horizontal resolution) to delineate the area flooded at each water level. The availability of these maps, along with Internet information regarding current stage from the USGS streamgage and forecasted high-flow stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Simulating the arrangement of subsystem to reduce inundation in the drainage system of Pepelegi housing area Sidoarjo

NASA Astrophysics Data System (ADS)

Brouwer, Steven; Wardoyo, Wasis; Lasminto, Umboro

2017-06-01

Pepelegi Indah Resident is a place which is frequently inundated by floodwater. This condition happened since the drainage system was designed with inappropriate waterflow method. The concern of this research was to figure out alternatives by managing the floodwater from the disposal drainage system. The existing information showed the area would be inundated if rainfall occurred for 2-3 hours. Half of Pepelegi Indah Resident would be inundated and subsidence time of flood on vulnerable time was 5-24 hours. To reduce the floodwater, some scenarios or simulations were carried out among others the management of tertiary drainage, the pool accommodation, and the provision of pumps at the enable point. From the simulation, the researcher should choose the best scenario which worked and optimally reduce the flooding. Based on the simulation results, the best scenario is the pool accommodation with new pumps at the primary channel.

Performance Comparison of NAMI DANCE and FLOW-3D® Models in Tsunami Propagation, Inundation and Currents using NTHMP Benchmark Problems

NASA Astrophysics Data System (ADS)

Velioglu Sogut, Deniz; Yalciner, Ahmet Cevdet

2018-06-01

Field observations provide valuable data regarding nearshore tsunami impact, yet only in inundation areas where tsunami waves have already flooded. Therefore, tsunami modeling is essential to understand tsunami behavior and prepare for tsunami inundation. It is necessary that all numerical models used in tsunami emergency planning be subject to benchmark tests for validation and verification. This study focuses on two numerical codes, NAMI DANCE and FLOW-3D®, for validation and performance comparison. NAMI DANCE is an in-house tsunami numerical model developed by the Ocean Engineering Research Center of Middle East Technical University, Turkey and Laboratory of Special Research Bureau for Automation of Marine Research, Russia. FLOW-3D® is a general purpose computational fluid dynamics software, which was developed by scientists who pioneered in the design of the Volume-of-Fluid technique. The codes are validated and their performances are compared via analytical, experimental and field benchmark problems, which are documented in the ``Proceedings and Results of the 2011 National Tsunami Hazard Mitigation Program (NTHMP) Model Benchmarking Workshop'' and the ``Proceedings and Results of the NTHMP 2015 Tsunami Current Modeling Workshop". The variations between the numerical solutions of these two models are evaluated through statistical error analysis.

Flood-inundation maps for the Saluda River from Old Easley Bridge Road to Saluda Lake Dam near Greenville, South Carolina

USGS Publications Warehouse

Benedict, Stephen T.; Caldwell, Andral W.; Clark, Jimmy M.

2013-01-01

Digital flood-inundation maps for a 3.95-mile reach of the Saluda River from approximately 815 feet downstream from Old Easley Bridge Road to approximately 150 feet downstream from Saluda Lake Dam near Greenville, South Carolina, were developed by the U.S. Geological Survey (USGS). The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Saluda River near Greenville, South Carolina (station 02162500). Current conditions at the USGS streamgage may be obtained through the National Water Information System Web site at http://waterdata.usgs.gov/sc/nwis/uv/?site_no=02162500&PARAmeter_cd=00065,00060,00062. The National Weather Service (NWS) forecasts flood hydrographs at many places that are often collocated with USGS streamgages. Forecasted peak-stage information is available on the Internet at the NWS Advanced Hydrologic Prediction Service (AHPS) flood-warning system Web site (http://water.weather.gov/ahps/) and may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation.In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-streamflow relations at USGS streamgage station 02162500, Saluda River near Greenville, South Carolina. The hydraulic model was then used to determine water-surface profiles for flood stages at 1.0-foot intervals referenced to the streamgage datum and ranging from approximately bankfull to 2 feet higher than the highest recorded water level at the streamgage. The simulated water-surface profiles were then exported to a geographic information system, ArcGIS, and combined with a digital elevation model (derived from Light Detection and Ranging [LiDAR] data with a 0.6-foot vertical Root Mean Square Error [RMSE] and a 3.0-foot horizontal RMSE), using HEC-GeoRAS tools in order to delineate the area flooded at each water level. The availability of these maps, along with real-time stage data from the USGS streamgage station 02162500 and forecasted stream stages from the NWS, can provide emergency management personnel and residents with information that is critical during flood-response and flood-recovery activities, such as evacuations, road closures, and disaster declarations.

Development of Flood Inundation Libraries using Historical Satellite Data and DEM for Part of Godavari Basin: An Approach Towards Better Flood Management

NASA Astrophysics Data System (ADS)

Bhatt, C. M.; Rao, G. S.; Patro, B.

2014-12-01

Conventional method of identifying areas to be inundated for issuing flood alert require inputs like discharge data, fine resolution digital elevation model (DEM), software for modelling and technically trained manpower to interpret the results meaningfully. Due to poor availability of these inputs, including good network of historical hydrological observations and limitation of time, quick flood early warning becomes a difficult task. Presently, based on the daily river water level and forecasted water level for major river systems in India, flood alerts are provided which are non-spatial in nature and does not help in understanding the inundation (spatial dimension) which may be caused at various water levels. In the present paper a concept for developing a series of flood-inundation map libraries two approaches are adopted one by correlating inundation extent derived from historical satellite data analysis with the corresponding water level recorded by the gauge station and the other simulation of inundation using digital elevation model (DEM's) is demonstrated for a part of Godavari Basin. The approach explained can be one of quick and cost-effective method for building a library of flood inundation extents, which can be utilized during flood disaster for alerting population and taking the relief and rescue operations. This layer can be visualized from a spatial dimension together with other spatial information like administrative boundaries, transport network, land use and land cover, digital elevation data and satellite images for better understanding and visualization of areas to be inundated spatially on free web based earth visualization portals like ISRO's Bhuvan portal (http://bhuvan.nrsc.gov.in). This can help decision makers in taking quick appropriate measures for warning, planning relief and rescue operations for the population to get affected under that river stage.

Integrating Physical and Topographic Information Into a Fuzzy Scheme to Map Flooded Area by SAR.

PubMed

Pierdicca, Nazzareno; Chini, Marco; Pulvirenti, Luca; Macina, Flavia

2008-07-10

A flood mapping procedure based on a fuzzy sets theory has been developed. The method is based on the integration of Synthetic Aperture Radar (SAR) measurements with additional data on the inundated area, such as a land cover map and a digital elevation model (DEM). The information on land cover has allowed us to account for both specular reflection, typical of open water, and double bounce backscattering, typical of forested and urban areas. DEM has been exploited to include simple hydraulic considerations on the dependence of inundation probability on surface characteristics. Contextual information has been taken into account too. The proposed algorithm has been tested on a flood occurred in Italy on November 1994. A pair of ERS-1 images, collected before and after (three days later) the flood, has been used. The results have been compared with the data provided by a ground survey carried out when the flood reached its maximum extension. Despite the temporal mismatch between the survey and the post-inundation SAR image, the comparison has yielded encouraging results, with the 87% of the pixels correctly classified as inundated.

Hurricane Katrina

Atmospheric Science Data Center

2014-05-15

... camera. Such a display causes water bodies and inundated soil to appear in blue and purple hues, and highly vegetated areas to appear ... MISR's oblique cameras, indicating the presence of inundated soil throughout the floodplain. Note that clouds appear in a different spot for ...

Development of Probabilistic Flood Inundation Mapping For Flooding Induced by Dam Failure

NASA Astrophysics Data System (ADS)

Tsai, C.; Yeh, J. J. J.

2017-12-01

A primary function of flood inundation mapping is to forecast flood hazards and assess potential losses. However, uncertainties limit the reliability of inundation hazard assessments. Major sources of uncertainty should be taken into consideration by an optimal flood management strategy. This study focuses on the 20km reach downstream of the Shihmen Reservoir in Taiwan. A dam failure induced flood herein provides the upstream boundary conditions of flood routing. The two major sources of uncertainty that are considered in the hydraulic model and the flood inundation mapping herein are uncertainties in the dam break model and uncertainty of the roughness coefficient. The perturbance moment method is applied to a dam break model and the hydro system model to develop probabilistic flood inundation mapping. Various numbers of uncertain variables can be considered in these models and the variability of outputs can be quantified. The probabilistic flood inundation mapping for dam break induced floods can be developed with consideration of the variability of output using a commonly used HEC-RAS model. Different probabilistic flood inundation mappings are discussed and compared. Probabilistic flood inundation mappings are hoped to provide new physical insights in support of the evaluation of concerning reservoir flooded areas.

Flood-Inundation Maps for a 1.6-Mile Reach of Salt Creek, Wood Dale, Illinois

USGS Publications Warehouse

Soong, David T.; Murphy, Elizabeth A.; Sharpe, Jennifer B.

2012-01-01

Digital flood-inundation maps for a 1.6-mile reach of Salt Creek from upstream of the Chicago, Milwaukee, St. Paul & Pacific Railroad to Elizabeth Drive, Wood Dale, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the DuPage County Stormwater Management Division. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage on Salt Creek at Wood Dale, Illinois (station number 05531175). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05531175. In this study, flood profiles were computed for the stream reach by means of a one-dimensional unsteady flow Full EQuations (FEQ) model. The unsteady flow model was verified by comparing the rating curve output for a September 2008 flood event to discharge measurements collected at the Salt Creek at Wood Dale gage. The hydraulic model was then used to determine 14 water-surface profiles for gage heights at 0.5-ft intervals referenced to the streamgage datum and ranging from less than bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) Digital Elevation Model (DEM) (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The areal extent of the inundation was verified with high-water marks from a flood in July 2010 with a peak gage height of 14.08 ft recorded at the Salt Creek at Wood Dale gage. The availability of these maps along with Internet information regarding current gage height from USGS streamgages provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post-flood recovery efforts.

Flood-inundation maps for Peachtree Creek from the Norfolk Southern Railway bridge to the Moores Mill Road NW bridge, Atlanta, Georgia

USGS Publications Warehouse

Musser, Jonathan W.

2012-01-01

Digital flood-inundation maps for a 5.5-mile reach of the Peachtree Creek from the Norfolk Southern Railway bridge to the Moores Mill Road NW bridge, were developed by the U.S. Geological Survey (USGS) in cooperation with the City of Atlanta, Georgia. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Peachtree Creek at Atlanta, Georgia (02336300) and the USGS streamgage at Chattahoochee River at Georgia 280, near Atlanta, Georgia (02336490). Current water level (stage) at these USGS streamgages may be obtained at http://waterdata.usgs.gov/ and can be used in conjunction with these maps to estimate near real-time areas of inundation. The National Weather Service (NWS) is incorporating results from this study into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http:/water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that commonly are collocated at USGS streamgages. The forecasted peak-stage information for the USGS streamgage at Peachtree Creek, which is available through the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. A one-dimensional step-backwater model was developed using the U.S. Army Corps of Engineers HEC–RAS software for a 6.5-mile reach of Peachtree Creek and was used to compute flood profiles for a 5.5-mile reach of the creek. The model was calibrated using the most current stage-discharge relations at the Peachtree Creek at Atlanta, Georgia, streamgage (02336300), and the Chattahoochee River at Georgia 280, near Atlanta, Georgia, streamgage (02336490) as well as high water marks collected during the 2010 annual peak flow event. The hydraulic model was then used to determine 50 water-surface profiles. The profiles are for 10 flood stages at the Peachtree Creek streamgage at 1-foot intervals referenced to the streamgage datum and ranging from just above bankfull stage (15.0 feet) to approximately the highest recorded water level at the streamgage (24.0 feet). At each stage on Peachtree Creek, five stages at the Chattahoochee River streamgage, from 26.4 feet to 38.4 feet in 3-foot intervals, were used to determine backwater effects. The simulated water-surface profiles were then combined with a geographic information system digital elevation model—derived from Light Detection and Ranging (LiDAR) data having a 0.3-foot vertical and 16.4-foot horizontal resolution—to delineate the area flooded for each 1-foot increment of stream stage. The availability of these maps, when combined with real-time information regarding current stage from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with critical information during flood response activities, such as evacuations and road closures as well as for postflood-recovery efforts.

Does Morphological Adjustment During Tsunami Inundation Increase Levels of Hazard?

NASA Astrophysics Data System (ADS)

Tehranirad, B.; Kirby, J. T., Jr.; Shi, F.; Grilli, S. T.

2016-12-01

Previous inundation mapping results for the US East Coast have shown that barrier islands would be among the most impacted areas during a possible tsunami. Many of these barriers are home to large population centers such as Atlantic City, NJ and Ocean City, MD. A tsunami can significantly change coastal morphology. Post-tsunami surveys have shown that large amounts of sediment can be moved in bays and estuaries by tsunami action, especially over coastal dunes. During tsunami inundation, large amounts of sediment have been eroded from sandy coasts and deposited further onshore. In some cases, sand dunes have been completely eroded by a tsunami, with the eroded sediment being deposited either onshore behind the dunes, or offshore during the rundown process. Given the potential for tsunamis to change coastal morphology, it is necessary to consider whether barrier island morphology change during inundation, if accounted for, would increase the assessment of tsunami hazard identified in the development of inundation and evacuation maps. In this presentation, we will show the results of our recent study on the morphological response of barrier islands during possible tsunamis that threaten the US East Coast. For this purpose, we have coupled the Boussinesq model FUNWAVE-TVD with a depth-averaged advection-diffusion sediment transport model and a morphology module to capture bed evolution under tsunami conditions. The model is verified in comparison to laboratory observations and to observed erosion/deposition patterns in Crescent City, CA harbor during the 2011 Tohoku-oki tsunami. We then use the model to study the effect of morphology change on predicted inundation limits for two barrier islands: the undeveloped Assateague Island, and the developed Ocean City, MD, using the tsunami sources utilized in previous hazard analysis. Our results suggest that significant bathymetric changes could be expected on a barrier island during tsunami inundation, leading to large increases in inundation areas for some of the events, particularly for smaller events where inundation without progressive dune breaching is minor.

GLOFRIM v1.0 - A globally applicable computational framework for integrated hydrological-hydrodynamic modelling

NASA Astrophysics Data System (ADS)

Hoch, Jannis M.; Neal, Jeffrey C.; Baart, Fedor; van Beek, Rens; Winsemius, Hessel C.; Bates, Paul D.; Bierkens, Marc F. P.

2017-10-01

We here present GLOFRIM, a globally applicable computational framework for integrated hydrological-hydrodynamic modelling. GLOFRIM facilitates spatially explicit coupling of hydrodynamic and hydrologic models and caters for an ensemble of models to be coupled. It currently encompasses the global hydrological model PCR-GLOBWB as well as the hydrodynamic models Delft3D Flexible Mesh (DFM; solving the full shallow-water equations and allowing for spatially flexible meshing) and LISFLOOD-FP (LFP; solving the local inertia equations and running on regular grids). The main advantages of the framework are its open and free access, its global applicability, its versatility, and its extensibility with other hydrological or hydrodynamic models. Before applying GLOFRIM to an actual test case, we benchmarked both DFM and LFP for a synthetic test case. Results show that for sub-critical flow conditions, discharge response to the same input signal is near-identical for both models, which agrees with previous studies. We subsequently applied the framework to the Amazon River basin to not only test the framework thoroughly, but also to perform a first-ever benchmark of flexible and regular grids on a large-scale. Both DFM and LFP produce comparable results in terms of simulated discharge with LFP exhibiting slightly higher accuracy as expressed by a Kling-Gupta efficiency of 0.82 compared to 0.76 for DFM. However, benchmarking inundation extent between DFM and LFP over the entire study area, a critical success index of 0.46 was obtained, indicating that the models disagree as often as they agree. Differences between models in both simulated discharge and inundation extent are to a large extent attributable to the gridding techniques employed. In fact, the results show that both the numerical scheme of the inundation model and the gridding technique can contribute to deviations in simulated inundation extent as we control for model forcing and boundary conditions. This study shows that the presented computational framework is robust and widely applicable. GLOFRIM is designed as open access and easily extendable, and thus we hope that other large-scale hydrological and hydrodynamic models will be added. Eventually, more locally relevant processes would be captured and more robust model inter-comparison, benchmarking, and ensemble simulations of flood hazard on a large scale would be allowed for.

Spatial and temporal controls of atoll island inundation: implications for urbanized atolls in the Marshall Islands.

NASA Astrophysics Data System (ADS)

Ford, M.; Becker, J. M.; Merrifield, M. A.

2012-12-01

Atoll islands are highly vulnerable to a range of inundation hazards. The impacts of such hazards are expected to be magnified as a result of continued sea-level rise. Both recent and historic inundation events provide unique insights into the requisite conditions necessary to initiate island inundation. A number of recent and historic inundation events are presented in order to examine the oceanographic and meteorological conditions driving inundation of a densely populated, urbanized atoll in the central Pacific. Analysis of inundation events suggests that a number of key drivers contribute to the spatial and temporal extent of island inundation, with unique degrees of predictability and resultant impact signatures apparent on island geomorphology and local anthropogenic activities. Results indicate three distinct drivers of inundation hazards exist. Firstly, tropical storms and typhoons elevate sea level through inverse barometric setup, wind setup and a range of wave driven processes and have caused considerable impact on atolls within the Marshall Islands. Secondly, super-elevated sea level conditions resulting from the combination of seasonal high tides and quasi-cyclical La Nina conditions drive inundation of low-lying lagoon facing coastal areas. Thirdly, long period swell conditions, typically generated by distant storms, can elevate reef-flat water levels through wave setup and infragravity wave oscillations. Such wave conditions can over wash the ocean-facing island ridge, often inundating large sections of the island. Reef-flat wave conditions are tidally modulated, with inundation events typically occurring around high tide. However, the two most recent destructive swell-driven inundation events have occurred while tide levels were significantly lower than spring tide levels, suggesting high water levels are not a necessary prerequisite for wave-driven inundation. The different modes of inundation are discussed and grounded within recent and historic inundation events, as well as results of a lengthy reef flat wave observation dataset from Kwajalein and Majuro Atolls in the Republic of the Marshall Islands. Future impacts of continued sea-level rise are considered on each mode of island inundation and the implications for local response discussed within the context of urbanised atoll islands.

Building regional early flood warning systems by AI techniques

NASA Astrophysics Data System (ADS)

Chang, F. J.; Chang, L. C.; Amin, M. Z. B. M.

2017-12-01

Building early flood warning system is essential for the protection of the residents against flood hazards and make actions to mitigate the losses. This study implements AI technology for forecasting multi-step-ahead regional flood inundation maps during storm events. The methodology includes three major schemes: (1) configuring the self-organizing map (SOM) to categorize a large number of regional inundation maps into a meaningful topology; (2) building dynamic neural networks to forecast multi-step-ahead average inundated depths (AID); and (3) adjusting the weights of the selected neuron in the constructed SOM based on the forecasted AID to obtain real-time regional inundation maps. The proposed models are trained, and tested based on a large number of inundation data sets collected in regions with the most frequent and serious flooding in the river basin. The results appear that the SOM topological relationships between individual neurons and their neighbouring neurons are visible and clearly distinguishable, and the hybrid model can continuously provide multistep-ahead visible regional inundation maps with high resolution during storm events, which have relatively small RMSE values and high R2 as compared with numerical simulation data sets. The computing time is only few seconds, and thereby leads to real-time regional flood inundation forecasting and make early flood inundation warning system. We demonstrate that the proposed hybrid ANN-based model has a robust and reliable predictive ability and can be used for early warning to mitigate flood disasters.

Influence of changes in wetland inundation extent on net fluxes of carbon dioxide and methane in northern high latitudes from 1993 to 2004

USGS Publications Warehouse

Zhuang, Qianlai; Zhu, Xudong; He, Yujie; Prigent, Catherine; Melillo, Jerry M.; McGuire, A. David; Prinn, Ronald G.; Kicklighter, David W.

2015-01-01

Estimates of the seasonal and interannual exchanges of carbon dioxide (CO2) and methane (CH4) between land ecosystems north of 45°N and the atmosphere are poorly constrained, in part, because of uncertainty in the temporal variability of water-inundated land area. Here we apply a process-based biogeochemistry model to evaluate how interannual changes in wetland inundation extent might have influenced the overall carbon dynamics of the region during the time period 1993–2004. We find that consideration by our model of these interannual variations between 1993 and 2004, on average, results in regional estimates of net methane sources of 67.8 ± 6.2 Tg CH4 yr−1, which is intermediate to model estimates that use two static inundation extent datasets (51.3 ± 2.6 and 73.0 ± 3.6 Tg CH4 yr−1). In contrast, consideration of interannual changes of wetland inundation extent result in regional estimates of the net CO2 sink of −1.28 ± 0.03 Pg C yr−1 with a persistent wetland carbon sink from −0.38 to −0.41 Pg C yr−1 and a upland sink from −0.82 to −0.98 Pg C yr−1. Taken together, despite the large methane emissions from wetlands, the region is a consistent greenhouse gas sink per global warming potential (GWP) calculations irrespective of the type of wetland datasets being used. However, the use of satellite-detected wetland inundation extent estimates a smaller regional GWP sink than that estimated using static wetland datasets. Our sensitivity analysis indicates that if wetland inundation extent increases or decreases by 10% in each wetland grid cell, the regional source of methane increases 13% or decreases 12%, respectively. In contrast, the regional CO2 sink responds with only 7–9% changes to the changes in wetland inundation extent. Seasonally, the inundated area changes result in higher summer CH4 emissions, but lower summer CO2 sinks, leading to lower summer negative greenhouse gas forcing. Our analysis further indicates that wetlands play a disproportionally important role in affecting regional greenhouse gas budgets given that they only occupy approximately 10% of the total land area in the region.

Tsunami hazard map in eastern Bali

NASA Astrophysics Data System (ADS)

Afif, Haunan; Cipta, Athanasius

2015-04-01

Bali is a popular tourist destination both for Indonesian and foreign visitors. However, Bali is located close to the collision zone between the Indo-Australian Plate and Eurasian Plate in the south and back-arc thrust off the northern coast of Bali resulted Bali prone to earthquake and tsunami. Tsunami hazard map is needed for better understanding of hazard level in a particular area and tsunami modeling is one of the most reliable techniques to produce hazard map. Tsunami modeling conducted using TUNAMI N2 and set for two tsunami sources scenarios which are subduction zone in the south of Bali and back thrust in the north of Bali. Tsunami hazard zone is divided into 3 zones, the first is a high hazard zones with inundation height of more than 3m. The second is a moderate hazard zone with inundation height 1 to 3m and the third is a low tsunami hazard zones with tsunami inundation heights less than 1m. Those 2 scenarios showed southern region has a greater potential of tsunami impact than the northern areas. This is obviously shown in the distribution of the inundated area in the south of Bali including the island of Nusa Penida, Nusa Lembongan and Nusa Ceningan is wider than in the northern coast of Bali although the northern region of the Nusa Penida Island more inundated due to the coastal topography.

Tsunami hazard map in eastern Bali

DOE Office of Scientific and Technical Information (OSTI.GOV)

Afif, Haunan, E-mail: afif@vsi.esdm.go.id; Cipta, Athanasius; Australian National University, Canberra

Bali is a popular tourist destination both for Indonesian and foreign visitors. However, Bali is located close to the collision zone between the Indo-Australian Plate and Eurasian Plate in the south and back-arc thrust off the northern coast of Bali resulted Bali prone to earthquake and tsunami. Tsunami hazard map is needed for better understanding of hazard level in a particular area and tsunami modeling is one of the most reliable techniques to produce hazard map. Tsunami modeling conducted using TUNAMI N2 and set for two tsunami sources scenarios which are subduction zone in the south of Bali and backmore » thrust in the north of Bali. Tsunami hazard zone is divided into 3 zones, the first is a high hazard zones with inundation height of more than 3m. The second is a moderate hazard zone with inundation height 1 to 3m and the third is a low tsunami hazard zones with tsunami inundation heights less than 1m. Those 2 scenarios showed southern region has a greater potential of tsunami impact than the northern areas. This is obviously shown in the distribution of the inundated area in the south of Bali including the island of Nusa Penida, Nusa Lembongan and Nusa Ceningan is wider than in the northern coast of Bali although the northern region of the Nusa Penida Island more inundated due to the coastal topography.« less

Elevation uncertainty in coastal inundation hazard assessments

USGS Publications Warehouse

Gesch, Dean B.; Cheval, Sorin

2012-01-01

Coastal inundation has been identified as an important natural hazard that affects densely populated and built-up areas (Subcommittee on Disaster Reduction, 2008). Inundation, or coastal flooding, can result from various physical processes, including storm surges, tsunamis, intense precipitation events, and extreme high tides. Such events cause quickly rising water levels. When rapidly rising water levels overwhelm flood defenses, especially in heavily populated areas, the potential of the hazard is realized and a natural disaster results. Two noteworthy recent examples of such natural disasters resulting from coastal inundation are the Hurricane Katrina storm surge in 2005 along the Gulf of Mexico coast in the United States, and the tsunami in northern Japan in 2011. Longer term, slowly varying processes such as land subsidence (Committee on Floodplain Mapping Technologies, 2007) and sea-level rise also can result in coastal inundation, although such conditions do not have the rapid water level rise associated with other flooding events. Geospatial data are a critical resource for conducting assessments of the potential impacts of coastal inundation, and geospatial representations of the topography in the form of elevation measurements are a primary source of information for identifying the natural and human components of the landscape that are at risk. Recently, the quantity and quality of elevation data available for the coastal zone have increased markedly, and this availability facilitates more detailed and comprehensive hazard impact assessments.

Estuarine Response to River Flow and Sea-Level Rise under Future Climate Change and Human Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Zhaoqing; Wang, Taiping; Voisin, Nathalie

Understanding the response of river flow and estuarine hydrodynamics to climate change, land-use/land-cover change (LULC), and sea-level rise is essential to managing water resources and stress on living organisms under these changing conditions. This paper presents a modeling study using a watershed hydrology model and an estuarine hydrodynamic model, in a one-way coupling, to investigate the estuarine hydrodynamic response to sea-level rise and change in river flow due to the effect of future climate and LULC changes in the Snohomish River estuary, Washington, USA. A set of hydrodynamic variables, including salinity intrusion points, average water depth, and salinity of themore » inundated area, were used to quantify the estuarine response to river flow and sea-level rise. Model results suggest that salinity intrusion points in the Snohomish River estuary and the average salinity of the inundated areas are a nonlinear function of river flow, although the average water depth in the inundated area is approximately linear with river flow. Future climate changes will shift salinity intrusion points further upstream under low flow conditions and further downstream under high flow conditions. In contrast, under the future LULC change scenario, the salinity intrusion point will shift downstream under both low and high flow conditions, compared to present conditions. The model results also suggest that the average water depth in the inundated areas increases linearly with sea-level rise but at a slower rate, and the average salinity in the inundated areas increases linearly with sea-level rise; however, the response of salinity intrusion points in the river to sea-level rise is strongly nonlinear.« less

USACE Extreme Sea Levels Advice on Guidance on Procedures to Evaluate and Adapt to Changes in Mean and Extreme Sea Levels.

DTIC Science & Technology

2014-09-09

influences of changes in extreme sea levels as they affect the four mission areas of USACE: storm damage reduction, flood risk mitigation, ecosystems...winds and surface pressure can occur on the scale of the inundation area under investigation, cyclonic climatologies and more sophisticated inundation...Federal and State agencies (particularly the Bureau of Meteorology) providing forecast data (e.g. DIPNR, 2005, Appendix N). In more developed areas of

Variations in Community Exposure and Sensitivity to Tsunami Hazards on the Open-Ocean and Strait of Juan de Fuca Coasts of Washington

USGS Publications Warehouse

Wood, Nathan; Soulard, Christopher

2008-01-01

Evidence of past events and modeling of potential future events suggest that tsunamis are significant threats to communities on the open-ocean and Strait of Juan de Fuca coasts of Washington. Although potential tsunami-inundation zones from a Cascadia Subduction Zone (CSZ) earthquake have been delineated, the amount and type of human development in tsunami-prone areas have not been documented. A vulnerability assessment using geographic-information-system tools was conducted to document variations in developed land, human populations, economic assets, and critical facilities relative to CSZ-related tsunami-inundation zones among communities on the open-ocean and Strait of Juan de Fuca coasts of Washington (including Clallam, Jefferson, Grays Harbor, and Pacific Counties). The tsunami-inundation zone in these counties contains 42,972 residents (24 percent of the total study-area population), 24,934 employees (33 percent of the total labor force), and 17,029 daily visitors to coastal Washington State Parks. The tsunami-inundation zone also contains 2,908 businesses that generate $4.6 billion in annual sales volume (31 and 40 percent of study-area totals, respectively) and tax parcels with a combined total value of $4.5 billion (25 percent of the study-area total). Although occupancy values are not known for each site, the tsunami-inundation zone also contains numerous dependent-population facilities (for example, schools and child-day-care centers), public venues (for example, religious organizations), and critical facilities (for example, police stations and public-work facilities). Racial diversity of residents in tsunami-prone areas is low?89 percent of residents are White and 8 percent are American Indian or Alaska Native. Nineteen percent of the residents in the tsunami-inundation zone are over 65 years in age, 30 percent of the residents live on unincorporated county lands, and 35 percent of the households are renter occupied. Employees in the tsunami-inundation zone are largely in businesses related to health care and social assistance, accommodation and food services, and retail trade, reflecting businesses that cater to a growing retiree and tourist population. Community vulnerability, described here by exposure (the amount of assets in tsunami-prone areas) and sensitivity (the relative percentage of assets in tsunami-prone areas) varies among 13 incorporated cities, 7 Indian reservations, and 4 counties. The City of Aberdeen has the highest relative community exposure to tsunamis, whereas the City of Long Beach has the highest relative community sensitivity. Levels of community exposure and sensitivity to tsunamis are found to be related to the amount and percentage, respectively, of a community?s land that is in a tsunami-inundation zone. This report will further the dialogue on societal risk to tsunami hazards in Washington and help risk managers to determine where additional risk-reduction strategies may be needed.

SLR-induced temporal and spatial changes in hotspots to storms along the Catalan coast

NASA Astrophysics Data System (ADS)

Jiménez, Jose A.; Sanuy, Marc; Valdemoro, Herminia

2017-04-01

Coastal hotspots to storms can be simply defined as locations where the magnitude of the storm-induced risk is significantly higher than neighbouring areas for a given probability of occurrence. Their distribution along the coast depends on the magnitude of storm-induced hazards and on the coastal resilient capacity. Increasing damages observed in our coasts during the last decades have driven the need to include specific chapters on risk management in ICZM plans. In this context, the identification of hotspots is one of the first points to be considered. This permits to better allocate resources for risk management by concentrating efforts in specific locations. Within this context, we have identified hotspots along the Catalan coast (Spanish Mediterranean) to storm-induced erosion and inundation hazards. This has been done by using the methodology developed within the RISCKIT EU project where storm-induced hazards (erosion and inundation) are characterised in probabilistic terms by using simple inundation and erosion models as a function of water level and wave climates and local coastal morphology. The final result was a set of inundation and erosion hotspots along the coast under current conditions for selected probabilities of occurrences, P. For low return periods, Tr, few hotspots appear and they represent coastal locations frequently affected by the corresponding hazard. On the other, for high Tr, a larger number (and of larger extension) of hotspots appear, that although less frequently affected, they are subjected to a larger impact. Although this is valuable information for coastal managers, it is only valid for making decisions for a short time horizon or under steady conditions. However, since the proper time scale for coastal planning is in the order of several decades, it is not likely that conditions will remain steady. Thus, although most of existing predictions of climate-induce changes in storminess in the Mediterranean indicate the absence of any significant increasing trend, this does not imply that storm-induced coastal hazards will not change. Thus, SLR will induce a series of long-term changes in coastal areas that although not directly affecting storminess will modify the coastal resilient capacity and, thus, changing coastal storm risks. To provide long-term predictions of hotspot, we have assessed the long-term SLR influence on erosion and inundation risks. To do this, an equilibrium-based approach has been adopted in which background SLR-induced shoreline retreat and beach vertical response are assessed for different SLR scenarios. Obtained values are used to predict future coastal morphology and to compute the resilient capacity for each beach at any time horizon. With this information, future erosion and inundation risks and corresponding new spatial distributions of coastal hotspots are calculated for selected probabilities. Obtained results show a significant increase in hotspots along the coast, with most of the changes concentrated in areas with small accommodation space and dominated by mild slope shorefaces. The extension of the new hotspots seems to indicate than unless land planning is considered as a tool for risk reduction, massive protection need to be implemented in certain areas.

A wetting and drying scheme for ROMS

USGS Publications Warehouse

Warner, John C.; Defne, Zafer; Haas, Kevin; Arango, Hernan G.

2013-01-01

The processes of wetting and drying have many important physical and biological impacts on shallow water systems. Inundation and dewatering effects on coastal mud flats and beaches occur on various time scales ranging from storm surge, periodic rise and fall of the tide, to infragravity wave motions. To correctly simulate these physical processes with a numerical model requires the capability of the computational cells to become inundated and dewatered. In this paper, we describe a method for wetting and drying based on an approach consistent with a cell-face blocking algorithm. The method allows water to always flow into any cell, but prevents outflow from a cell when the total depth in that cell is less than a user defined critical value. We describe the method, the implementation into the three-dimensional Regional Oceanographic Modeling System (ROMS), and exhibit the new capability under three scenarios: an analytical expression for shallow water flows, a dam break test case, and a realistic application to part of a wetland area along the Georgia Coast, USA.

Environmental modeling in data-sparse regions: Mozambique demonstrator case

NASA Astrophysics Data System (ADS)

Schumann, G.; Niebuhr, E.; Rashid, K.; Escobar, V. M.; Andreadis, K.; Njoku, E. G.; Neal, J. C.; Voisin, N.; Pappenberger, F.; Phanthuwongpakdee, N.; Bates, P. D.; Chao, Y.; Moller, D.; Paron, P.

2014-12-01

Long time-series computations of seasonal and flood event inundation volumes from archived forecast rainfall events for the Lower Zambezi basin (Mozambique), using a coupled hydrology-hydrodynamic model, are correlated and regressed with satellite soil moisture observations and NWP rainfall forecasts as predictors for inundation volumes. This dynamic library of volume predictions can then be re-projected onto the topography to generate the corresponding floodplain and wetland inundation dynamics, including periods of flood and low flows. Especially for data-poor regions, the application potential of such a library of data is invaluable as the modeling chain is greatly simplified and readily available. The library is flexible, portable and transitional. Furthermore, deriving environmental indicators from this dynamic look-up catalogue would be relatively straightforward. Application fields are various and here we present conceptually a few that we plan to research in more detail and on some of which we already collaborate with other scientists and international institutions, though at the moment largely on an unfunded basis. The primary application is to implement an early warning system for flood inundation relief operations and flood inundation mitigation and resilience. Having this flood inundation warning system set up adequately would also allow looking into long-term predictions of crop productivity and consequently food security. Another potentially high-impact application is to relate flood inundation dynamics to disease modeling for public health monitoring and prediction, in particular focusing on Malaria. Last but not least, the dynamic inundation library we are building can be validated and complemented with advanced airborne radar imagery of flooding and inundated wetlands to study changes in wetland ecology and biodiversity with unprecedented detail in data-poor regions, in this case in particular the important wetlands of the Zambezi Delta.

Forecasting inundation from debris flows that grow during travel, with application to the Oregon Coast Range, USA

USGS Publications Warehouse

Reid, Mark E.; Coe, Jeffrey A.; Brien, Dianne

2016-01-01

Many debris flows increase in volume as they travel downstream, enhancing their mobility and hazard. Volumetric growth can result from diverse physical processes, such as channel sediment entrainment, stream bank collapse, adjacent landsliding, hillslope erosion and rilling, and coalescence of multiple debris flows; incorporating these varied phenomena into physics-based debris-flow models is challenging. As an alternative, we embedded effects of debris-flow growth into an empirical/statistical approach to forecast potential inundation areas within digital landscapes in a GIS framework. Our approach used an empirical debris-growth function to account for the effects of growth phenomena. We applied this methodology to a debris-flow-prone area in the Oregon Coast Range, USA, where detailed mapping revealed areas of erosion and deposition along paths of debris flows that occurred during a large storm in 1996. Erosion was predominant in stream channels with slopes > 5°. Using pre- and post-event aerial photography, we derived upslope contributing area and channel-length growth factors. Our method reproduced the observed inundation patterns produced by individual debris flows; it also generated reproducible, objective potential inundation maps for entire drainage networks. These maps better matched observations than those using previous methods that focus on proximal or distal regions of a drainage network.

Validation of Forested Inundation Extent Revealed by L-Band Polarimetric and Interferometric SAR Data

NASA Technical Reports Server (NTRS)

Chapman, Bruce; Celi, Jorge; Hamilton, Steve; McDonald, Kyle

2013-01-01

UAVSAR, NASA's airborne Synthetic Aperture Radar (SAR), conducted an extended observational campaign in Central and South America in March 2013, primarily related to volcanic deformations along the Andean Mountain Range but also including a large number of flights studying other scientific phenomena. During this campaign, the L-Band SAR collected data over the Napo River in Ecuador. The objectives of this experiment were to acquire polarimetric and interferometric L-Band SAR data over an inundated tropical forest in Ecuador simultaneously with on-the-ground field work ascertaining the extent of inundation, and to then derive from this data a quantitative estimate for the error in the SAR-derived inundation extent. In this paper, we will first describe the processing and preliminary analysis of the SAR data. The polarimetric SAR data will be classified by land cover and inundation state. The interferometric SAR data will be used to identify those areas where change in inundation extent occurred, and to measure the change in water level between two observations separated by a week. Second, we will describe the collection of the field estimates of inundation, and have preliminary comparisons of inundation extent measured in the field field versus that estimated from the SAR data.

The impact of onsite wastewater disposal systems on groundwater in areas inundated by Hurricane Sandy in New York and New Jersey.

PubMed

Fisher, Irene J; Phillips, Patrick J; Colella, Kaitlyn M; Fisher, Shawn C; Tagliaferri, Tristen; Foreman, William T; Furlong, Edward T

2016-06-30

Coastal onsite wastewater disposal systems (OWDS) were inundated by Hurricane Sandy's storm tide. This study compares the shallow groundwater quality (nutrients, pharmaceuticals, and hormones) downgradient of OWDS before and after Hurricane Sandy, where available, and establishes a baseline for wastewater influence on groundwater in coastal communities inundated by Hurricane Sandy. Nutrients and contaminants of emerging concern (CECs) were detected in shallow groundwater downgradient of OWDS in two settings along the New Jersey and New York coastlines: 1) a single, centralized OWDS in a park; and 2) multiple OWDS (cesspools) in low-density residential and mixed-use/medium density residential areas. The most frequently detected pharmaceuticals were lidocaine (40%), carbamazepine (36%), and fexofenadine, bupropion, desvenlafaxine, meprobamate, and tramadol (24-32%). Increases in the number and total concentration of pharmaceuticals after Hurricane Sandy may reflect other factors (seasonality, usage) besides inundation, and demonstrate the importance of analyzing for a wide variety of CECs in regional studies. Published by Elsevier Ltd.

The impact of onsite wastewater disposal systems on groundwater in areas inundated by Hurricane Sandy in New York and New Jersey

USGS Publications Warehouse

Fisher, Irene; Phillips, Patrick J.; Colella, Kaitlyn; Fisher, Shawn C.; Tagliaferri, Tristen N.; Foreman, William T.; Furlong, Edward T.

2016-01-01

Coastal onsite wastewater disposal systems (OWDS) were inundated by Hurricane Sandy's storm tide. This study compares the shallow groundwater quality (nutrients, pharmaceuticals, and hormones) downgradient of OWDS before and after Hurricane Sandy, where available, and establishes a baseline for wastewater influence on groundwater in coastal communities inundated by Hurricane Sandy. Nutrients and contaminants of emerging concern (CECs) were detected in shallow groundwater downgradient of OWDS in two settings along the New Jersey and New York coastlines: 1) a single, centralized OWDS in a park; and 2) multiple OWDS (cesspools) in low-density residential and mixed-use/medium density residential areas. The most frequently detected pharmaceuticals were lidocaine (40%), carbamazepine (36%), and fexofenadine, bupropion, desvenlafaxine, meprobamate, and tramadol (24–32%). Increases in the number and total concentration of pharmaceuticals after Hurricane Sandy may reflect other factors (seasonality, usage) besides inundation, and demonstrate the importance of analyzing for a wide variety of CECs in regional studies.

Incorporating Tsunami Projections to Sea Level Rise Vulnerability Assessments -A Case Study for Midway Atoll-

NASA Astrophysics Data System (ADS)

Gica, E.; Reynolds, M.

2012-12-01

Recent global models predict a rise of approximately one meter in global sea level by 2100, with potentially larger increases in areas of the Pacific Ocean. If current climate change trends continue, low-lying islands across the globe may become inundated over the next century, placing island biodiversity at risk. Adding to the risk of inundation due to sea level rise is the occurrence of cyclones and tsunamis. This combined trend will affect the low-lying islands of the Northwestern Hawaiian Islands and it is therefore important to assess its impact since these islands are critical habitats to many endangered endemic species and support the largest tropical seabird rookery in the world. The 11 March 2011 Tohoku (Mw=8.8) earthquake-tsunami affected the habitat of many endangered endemic species in Midway Atoll National Wildlife Refuge because all three islands (Sand, Eastern and Spit) were inundated by tsunami waves. At present sea level, some tsunamis from certain source regions would not affect Midway Atoll. For example, the previous earthquake-tsunamis such as the 15 November 2006 Kuril (Mw=8.1) and 13 February 2007 Kuril (Mw=7.9) were not significant enough to affect Midway Atoll. But at higher sea levels, tsunamis with similar characteristics could pose a threat to such terrestrial habitats and wildlife. To visualize projected impacts to vegetation composition, wildlife habitat, and wildlife populations, we explored and analyzed inundation vulnerability for a range of possible sea level rise and tsunami scenarios at Midway Atoll National Wildlife Refuge. Studying the combined threat of tsunamis and sea level rise can provide more accurate and comprehensive assessments of the vulnerability of the unique natural resources on low-lying islands. A passive sea level rise model was used to determine how much inundation will occur at different sea level rise values for the three islands of Midway Atoll and each scenario was coupled with NOAA Center for Tsunami Research's tsunami forecasting tool. The tsunami forecasting tool was used to generate tsunami scenarios from different source regions and served as boundary conditions for inundation models to project the coastal impact at Midway Atoll. Underlying the tsunami forecast tool is a database of pre-computed tsunami propagation runs for discrete sections of the earth's subduction zones that are the principal locus of tsunami-generating activity. The new LiDAR topographic data, which is the first high resolution elevation data for three individual islands of Midway Atoll, was used for both the passive sea level rise model and inundation model for Midway Atoll. Results of the study will indicate how the combined climate change and tsunami occurrence will affect Midway Atoll and can therefore be used for early climate change adaptation and mitigation planning, especially for vulnerable species and areas of the Atoll.

Modeling Storm-Induced Inundation on the Yukon-Kuskokwim Delta for Present and Future Climates

NASA Astrophysics Data System (ADS)

Ravens, T. M.; Allen, J.

2012-12-01

The Yukon-Kuskokwim (YK) Delta is a large delta on the west coast of Alaska and one of the few remaining deltas that is largely free of anthropogenic impacts. The delta hosts a wide-range of nesting birds including the endangered Spectacled Eider. The delta plain, with an elevation of about 2 m (m.s.l.) - and an average tidal range of 2.7 m - is subject to frequent inundation by storm surges originating from the adjacent Bering Sea. Here, we report on our efforts to validate a storm-surge modeling system consisting of a course-grid ADCIRC model covering the Bering and Chukchi Seas and a Delft3D fine-grid model of the southern YK Delta. The storm surge models are validated based on measured water levels from 2007-2010 and using satellite observations of inundation due to large storms in 2005 and 2006. About 10 storms over the past 30 years are modeled. Based on model output, we computed a spatially distributed inundation index which is a time-integral of water level throughout the fine-grid model domain from individual storms and from the 30 year period. In order to examine the change in inundation in future climates, the models of the 30 year period were re-run assuming a 1 and 2 meter sea level rise. The impact of climate change on inundation frequency and intensity - using the inundation index - is reported. Future work will relate the present and projected inundation index to ecological parameters such as bird-nest concentration and vegetation type.

Integrating Physical and Topographic Information Into a Fuzzy Scheme to Map Flooded Area by SAR

PubMed Central

Pierdicca, Nazzareno; Chini, Marco; Pulvirenti, Luca; Macina, Flavia

2008-01-01

A flood mapping procedure based on a fuzzy sets theory has been developed. The method is based on the integration of Synthetic Aperture Radar (SAR) measurements with additional data on the inundated area, such as a land cover map and a digital elevation model (DEM). The information on land cover has allowed us to account for both specular reflection, typical of open water, and double bounce backscattering, typical of forested and urban areas. DEM has been exploited to include simple hydraulic considerations on the dependence of inundation probability on surface characteristics. Contextual information has been taken into account too. The proposed algorithm has been tested on a flood occurred in Italy on November 1994. A pair of ERS-1 images, collected before and after (three days later) the flood, has been used. The results have been compared with the data provided by a ground survey carried out when the flood reached its maximum extension. Despite the temporal mismatch between the survey and the post-inundation SAR image, the comparison has yielded encouraging results, with the 87% of the pixels correctly classified as inundated. PMID:27879928

Deterministic approach for multiple-source tsunami hazard assessment for Sines, Portugal

NASA Astrophysics Data System (ADS)

Wronna, M.; Omira, R.; Baptista, M. A.

2015-11-01

In this paper, we present a deterministic approach to tsunami hazard assessment for the city and harbour of Sines, Portugal, one of the test sites of project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe). Sines has one of the most important deep-water ports, which has oil-bearing, petrochemical, liquid-bulk, coal, and container terminals. The port and its industrial infrastructures face the ocean southwest towards the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, we selected a total of six scenarios to assess the tsunami impact at the test site. The tsunami simulations are computed using NSWING, a Non-linear Shallow Water model wIth Nested Grids. In this study, the static effect of tides is analysed for three different tidal stages: MLLW (mean lower low water), MSL (mean sea level), and MHHW (mean higher high water). For each scenario, the tsunami hazard is described by maximum values of wave height, flow depth, drawback, maximum inundation area and run-up. Synthetic waveforms are computed at virtual tide gauges at specific locations outside and inside the harbour. The final results describe the impact at the Sines test site considering the single scenarios at mean sea level, the aggregate scenario, and the influence of the tide on the aggregate scenario. The results confirm the composite source of Horseshoe and Marques de Pombal faults as the worst-case scenario, with wave heights of over 10 m, which reach the coast approximately 22 min after the rupture. It dominates the aggregate scenario by about 60 % of the impact area at the test site, considering maximum wave height and maximum flow depth. The HSMPF scenario inundates a total area of 3.5 km2.

Hydraulic and hydrologic aspects of flood-plain planning

USGS Publications Warehouse

Wiitala, S.W.; Jetter, K.R.; Sommerville, Alan J.

1961-01-01

The valid incentives compelling occupation of the flood plain, up to and eve n into the stream channel, undoubtedly have contributed greatly to the development of the country. But the result has been a heritage of flood disaster, suffering, and enormous costs. Flood destruction awakened a consciousness toward reduction and elimination of flood hazards, originally manifested in the protection of existing developments. More recently, increased knowledge of the problem has shown the impracticability of permitting development that requires costly flood protect/on. The idea of flood zoning, or flood-plain planning, has received greater impetus as a result of this realization. This study shows how hydraulic and hydrologic data concerning the flood regimen of a stream can be used in appraising its flood potential and the risk inherent in occupation of its flood plain. The approach involves the study of flood magnitudes as recorded or computed; flood frequencies based1 on experience shown by many years of gaging-station record; use of existing or computed stagedischarge relations and flood profiles; and, where required, the preparation of flood-zone maps to show the areas inundated by floods of several magnitudes and frequencies. The planner can delineate areas subject to inundation by floods o* specific recurrence intervals for three conditions: (a) for the immediate vicinity of a gaging station; (b) for a gaged stream at a considerable distance from a gaging station; and (c) for an ungaged stream. The average depth for a flood of specific frequency can be estimated on the basis of simple measurements of area of drainage basin, width of channel, and slope of streambed. This simplified approach should be useful in the initial stages of flood-plain planning. Brief discussions are included on various types of flood hazards, the effects of urbanization on flood runoff, and zoning considerations.

A Study on Active Disaster Management System for Standardized Emergency Action Plan using BIM and Flood Damage Estimation Techniques

NASA Astrophysics Data System (ADS)

Jeong, C.; Om, J.; Hwang, J.; Joo, K.; Heo, J.

2013-12-01

In recent, the frequency of extreme flood has been increasing due to climate change and global warming. Highly flood damages are mainly caused by the collapse of flood control structures such as dam and dike. In order to reduce these disasters, the disaster management system (DMS) through flood forecasting, inundation mapping, EAP (Emergency Action Plan) has been studied. The estimation of inundation damage and practical EAP are especially crucial to the DMS. However, it is difficult to predict inundation and take a proper action through DMS in real emergency situation because several techniques for inundation damage estimation are not integrated and EAP is supplied in the form of a document in Korea. In this study, the integrated simulation system including rainfall frequency analysis, rainfall-runoff modeling, inundation prediction, surface runoff analysis, and inland flood analysis was developed. Using this system coupled with standard GIS data, inundation damage can be estimated comprehensively and automatically. The standard EAP based on BIM (Building Information Modeling) was also established in this system. It is, therefore, expected that the inundation damages through this study over the entire area including buildings can be predicted and managed.

Characterization of Inundated Wetlands with Microwave Remote Sensing: Cross-Product Comparison for Uncertainty Assessment in Tropical Wetlands

NASA Astrophysics Data System (ADS)

McDonald, K. C.; Jensen, K.; Alvarez, J.; Azarderakhsh, M.; Schroeder, R.; Podest, E.; Chapman, B. D.; Zimmermann, R.

2015-12-01

We have been assembling a global-scale Earth System Data Record (ESDR) of natural Inundated Wetlands to facilitate investigations on their role in climate, biogeochemistry, hydrology, and biodiversity. The ESDR comprises (1) Fine-resolution (100 meter) maps, delineating wetland extent, vegetation type, and seasonal inundation dynamics for regional to continental-scale areas, and (2) global coarse-resolution (~25 km), multi-temporal mappings of inundated area fraction (Fw) across multiple years. During March 2013, the NASA/JPL L-band polarimetric airborne imaging radar, UAVSAR, conducted airborne studies over regions of South America including portions of the western Amazon basin. We collected UAVSAR datasets over regions of the Amazon basin during that time to support systematic analyses of error sources related to the Inundated Wetlands ESDR. UAVSAR datasets were collected over Pacaya Samiria, Peru, Madre de Dios, Peru, and the Napo River in Ecuador. We derive landcover classifications from the UAVSAR datasets emphasizing wetlands regions, identifying regions of open water and inundated vegetation. We compare the UAVSAR-based datasets with those comprising the ESDR to assess uncertainty associated with the high resolution and the coarse resolution ESDR components. Our goal is to create an enhanced ESDR of inundated wetlands with statistically robust uncertainty estimates. The ESDR documentation will include a detailed breakdown of error sources and associated uncertainties within the data record. This work was carried out in part within the framework of the ALOS Kyoto & Carbon Initiative. PALSAR data were provided by JAXA/EORC and the Alaska Satellite Facility. Portions of this work were conducted at the Jet Propulsion Laboratory, California Institute of Technology under contract to the National Aeronautics and Space Administration.

In situ genetic differentiation in a Hispaniolan lizard (Ameiva chrysolaema): a multilocus perspective.

PubMed

Gifford, Matthew E; Larson, Allan

2008-10-01

A previous phylogeographic study of mitochondrial haplotypes for the Hispaniolan lizard Ameiva chrysolaema revealed deep genetic structure associated with seawater inundation during the late Pliocene/early Pleistocene and evidence of subsequent population expansion into formerly inundated areas. We revisit hypotheses generated by our previous study using increased geographic sampling of populations and analysis of three nuclear markers (alpha-enolase intron 8, alpha-cardiac-actin intron 4, and beta-actin intron 3) in addition to mitochondrial haplotypes (ND2). Large genetic discontinuities correspond spatially and temporally with historical barriers to gene flow (sea inundations). NCPA cross-validation analysis and Bayesian multilocus analyses of divergence times (IMa and MCMCcoal) reveal two separate episodes of fragmentation associated with Pliocene and Pleistocene sea inundations, separating the species into historically separate Northern, East-Central, West-Central, and Southern population lineages. Multilocus Bayesian analysis using IMa indicates asymmetrical migration from the East-Central to the West-Central populations following secondary contact, consistent with expectations from the more pervasive sea inundation in the western region. The West-Central lineage has a genetic signature of population growth consistent with the expectation of geographic expansion into formerly inundated areas. Within each lineage, significant spatial genetic structure indicates isolation by distance at comparable temporal scales. This study adds to the growing body of evidence that vicariant speciation may be the prevailing source of lineage accumulation on oceanic islands. Thus, prior theories of island biogeography generally underestimate the role and temporal scale of intra-island vicariant processes.

Development of an Impact-Oriented Quantitative Coastal Inundation forecasting and early warning system with social and economic assessment

NASA Astrophysics Data System (ADS)

Fakhruddin, S. H. M.; Babel, Mukand S.; Kawasaki, Akiyuki

2014-05-01

Coastal inundations are an increasing threat to the lives and livelihoods of people living in low-lying, highly-populated coastal areas. According to a World Bank Report in 2005, at least 2.6 million people may have drowned due to coastal inundation, particularly caused by storm surges, over the last 200 years. Forecasting and prediction of natural events, such as tropical and extra-tropical cyclones, inland flooding, and severe winter weather, provide critical guidance to emergency managers and decision-makers from the local to the national level, with the goal of minimizing both human and economic losses. This guidance is used to facilitate evacuation route planning, post-disaster response and resource deployment, and critical infrastructure protection and securing, and it must be available within a time window in which decision makers can take appropriate action. Recognizing this extreme vulnerability of coastal areas to inundation/flooding, and with a view to improve safety-related services for the community, research should strongly enhance today's forecasting, prediction and early warning capabilities in order to improve the assessment of coastal vulnerability and risks and develop adequate prevention, mitigation and preparedness measures. This paper tries to develop an impact-oriented quantitative coastal inundation forecasting and early warning system with social and economic assessment to address the challenges faced by coastal communities to enhance their safety and to support sustainable development, through the improvement of coastal inundation forecasting and warning systems.

Historical and potential future impacts of extreme hydrological events on the Amazonian floodplain hydrology and inundation dynamics

NASA Astrophysics Data System (ADS)

Macedo, M.; Panday, P. K.; Coe, M. T.; Lefebvre, P.; Castello, L.

2015-12-01

The Amazonian floodplains and wetlands cover one fifth of the basin and are highly productive promoting diverse biological communities and sustaining human populations with fisheries. Seasonal inundation of the floodplains fluctuates in response to drought or extreme rainfall as observed in the recent droughts of 2005 and 2010 where river levels dropped to among the lowest recorded. We model and evaluate the historical (1940-2010) and projected future (2010-2100) impacts of droughts and floods on the floodplain hydrology and inundation dynamics in the central Amazon using the Integrated Biosphere Simulator (IBIS) and the Terrestrial Hydrology Model and Biogeochemistry (THMB). Simulated discharge correlates well with observed discharges for tributaries originating in Brazil but underestimates basins draining regions in the non-Brazilian Amazon (Solimões, Japuŕa, Madeira, and Negro) by greater than 30%. A volume bias-correction from the simulated and observed runoff was used to correct the input precipitation across the major tributaries of the Amazon basin that drain the Andes. Simulated hydrological parameters (discharge, inundated area and river height) using corrected precipitation has a strong correlation with field measured discharge at gauging stations, surface water extent data (Global Inundation Extent from Multi-Satellites (GIEMS) and NASA Earth System Data Records (ESDRs) for inundation), and satellite radar altimetry (TOPEX/POSEIDON altimeter data for 1992-1998 and ENVISAT data for 2002-2010). We also used an ensemble of model outputs participating in the IPCC AR5 to drive two sets of simulations with and without carbon dioxide fertilization for the 2006-2100 period, and evaluated the potential scale and variability of future changes in discharge and inundation dynamics due to the influences of climate change and vegetation response to carbon dioxide fertilization. Preliminary modeled results for future scenarios using Representative Concentration Pathways (RCP) 4.5 indicate decreases in projected discharge and extent of inundated area on the mainstem Amazon by the late 21st century owing to influences of future climate change only.

Utilising social media contents for flood inundation mapping

NASA Astrophysics Data System (ADS)

Schröter, Kai; Dransch, Doris; Fohringer, Joachim; Kreibich, Heidi

2016-04-01

Data about the hazard and its consequences are scarce and not readily available during and shortly after a disaster. An information source which should be explored in a more efficient way is eyewitness accounts via social media. This research presents a methodology that leverages social media content to support rapid inundation mapping, including inundation extent and water depth in the case of floods. It uses quantitative data that are estimated from photos extracted from social media posts and their integration with established data. Due to the rapid availability of these posts compared to traditional data sources such as remote sensing data, areas affected by a flood, for example, can be determined quickly. Key challenges are to filter the large number of posts to a manageable amount of potentially useful inundation-related information, and to interpret and integrate the posts into mapping procedures in a timely manner. We present a methodology and a tool ("PostDistiller") to filter geo-located posts from social media services which include links to photos and to further explore this spatial distributed contextualized in situ information for inundation mapping. The June 2013 flood in Dresden is used as an application case study in which we evaluate the utilization of this approach and compare the resulting spatial flood patterns and inundation depths to 'traditional' data sources and mapping approaches like water level observations and remote sensing flood masks. The outcomes of the application case are encouraging. Strengths of the proposed procedure are that information for the estimation of inundation depth is rapidly available, particularly in urban areas where it is of high interest and of great value because alternative information sources like remote sensing data analysis do not perform very well. The uncertainty of derived inundation depth data and the uncontrollable availability of the information sources are major threats to the utility of the approach.

Study of characteristic of tsunami base on the coastal morphology in north Donggala, Central Sulawesi

NASA Astrophysics Data System (ADS)

Rahmadaningsi, W. S. N.; Assegaf, A. H.; Setyonegoro, W.; Paharuddin

2018-03-01

The northern arm of Sulawesi potentials to generate earthquake and Tsunami due to the existence of subduction zone in sulawesi sea. It makes the North Donggala as an area with active seismicity. One of the earthquake and Tsunami events occurred is the earthquake and tsunami of Toli-Toli 1996 (M 7.9) causing 9 people are killed and severe damage in Tonggolobibi, Siboang, and Balukang. This earthquake induced tsunami runup of 3.4 m and inundated as far as 400 meters. The aims of this study is to predict runup and inundation area using numerical model and to find out the characteristics of Tsunami wave on straight, bay and cape shape coastal morphology and slopes of coastal. The data in this research consist of are the Etopo2 bathymetry data in data obtained from NOAA (National Oceanic and Atmospheric Administration), Toli-toli’s main earthquakes focal mechanism data 1st January1996 from GCMT (Global Centroid Moment Tensor), the data gained from the SRTM (Shuttle Radar Topography Mission) data 30 m and land cover data in 1996 from Ministry of environment and forestry . Single fault model is used to predict the high of tsunami run-up and to inundation area along Donggala coastal area. Its reviewed by morphology of coastal area that higher run up shows occurs at coastline type like bay have higher run up compare to area with cape and straight coastline. The result shows that the slopes have negative or contras correlation with Tsunami runup and its inundation area.

Early pictures of global climate change impact to the coastal area (North West of Demak Central Java Indonesia)

NASA Astrophysics Data System (ADS)

Andreas, Heri; Pradipta, Dhota; Abidin, Hasanuddin Z.; Sarsito, Dina A.

2017-07-01

In the last several decades we have been realized for the Global Climate Change situation. Some indicators are worldwide increasing temperature, decreasing volume of ice in Antarctica, and the sea level rise. Relating to the decreased of ice volume and the sea level rise, this situation has been predicted to endanger the living at the coastal area in the future. Prediction models have shown some coastal cities area would suffer flood by tidal inundation and even permanent flooding. Coincidently, today in the North West of Demak District Central Java Indonesia we literally can see the early picture of Global Climate Change impact to the coastal areas as mention. The occurrence of tidal inundation in this area was recognized at least in the early 2000 and even earlier, and in the recent years the tidal inundation comes not only at a high tide but even at the regular tide, and in fact some of this area are obviously sinking to the sea through times. This early picture is truly showing a disaster. Adaptation has been made in facing the disaster such as increasing the house and infrastructures, and built dyke. We have been done some investigations to this area by field observations (mapping the flooded area, interviewing people and seeing the adaptations, conduct GPS measurement to see deformation, etc.), gather information from digital media and also using remotely time series of high resolution satellite image data to mapping the tidal inundation in this area. We noted people increased their house and the local goverment elevated the road and the bridge, etc. regulary over less decade periode. Our conclusions said that the adaptation only made temporaly since the sea level keep rising worsening by the land subsidence significantly.

Seismic probabilistic tsunami hazard: from regional to local analysis and use of geological and historical observations

NASA Astrophysics Data System (ADS)

Tonini, R.; Lorito, S.; Orefice, S.; Graziani, L.; Brizuela, B.; Smedile, A.; Volpe, M.; Romano, F.; De Martini, P. M.; Maramai, A.; Selva, J.; Piatanesi, A.; Pantosti, D.

2016-12-01

Site-specific probabilistic tsunami hazard analyses demand very high computational efforts that are often reduced by introducing approximations on tsunami sources and/or tsunami modeling. On one hand, the large variability of source parameters implies the definition of a huge number of potential tsunami scenarios, whose omission could easily lead to important bias in the analysis. On the other hand, detailed inundation maps computed by tsunami numerical simulations require very long running time. When tsunami effects are calculated at regional scale, a common practice is to propagate tsunami waves in deep waters (up to 50-100 m depth) neglecting non-linear effects and using coarse bathymetric meshes. Then, maximum wave heights on the coast are empirically extrapolated, saving a significant amount of computational time. However, moving to local scale, such assumptions drop out and tsunami modeling would require much greater computational resources. In this work, we perform a local Seismic Probabilistic Tsunami Hazard Analysis (SPTHA) for the 50 km long coastal segment between Augusta and Siracusa, a touristic and commercial area placed along the South-Eastern Sicily coast, Italy. The procedure consists in using the outcomes of a regional SPTHA as input for a two-step filtering method to select and substantially reduce the number of scenarios contributing to the specific target area. These selected scenarios are modeled using high resolution topo-bathymetry for producing detailed inundation maps. Results are presented as probabilistic hazard curves and maps, with the goal of analyze, compare and highlight the different results provided by regional and local hazard assessments. Moreover, the analysis is enriched by the use of local observed tsunami data, both geological and historical. Indeed, tsunami data-sets available for the selected target areas are particularly rich with respect to the scarce and heterogeneous data-sets usually available elsewhere. Therefore, they can represent valuable benchmarks for testing and strengthening the results of such kind of studies. The work is funded by the Italian Flagship Project RITMARE, the two EC FP7 projects ASTARTE (Grant agreement 603839) and STREST (Grant agreement 603389), and the INGV-DPC Agreement.

Development and validation of a two-dimensional fast-response flood estimation model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judi, David R; Mcpherson, Timothy N; Burian, Steven J

2009-01-01

A finite difference formulation of the shallow water equations using an upwind differencing method was developed maintaining computational efficiency and accuracy such that it can be used as a fast-response flood estimation tool. The model was validated using both laboratory controlled experiments and an actual dam breach. Through the laboratory experiments, the model was shown to give good estimations of depth and velocity when compared to the measured data, as well as when compared to a more complex two-dimensional model. Additionally, the model was compared to high water mark data obtained from the failure of the Taum Sauk dam. Themore » simulated inundation extent agreed well with the observed extent, with the most notable differences resulting from the inability to model sediment transport. The results of these validation studies complex two-dimensional model. Additionally, the model was compared to high water mark data obtained from the failure of the Taum Sauk dam. The simulated inundation extent agreed well with the observed extent, with the most notable differences resulting from the inability to model sediment transport. The results of these validation studies show that a relatively numerical scheme used to solve the complete shallow water equations can be used to accurately estimate flood inundation. Future work will focus on further reducing the computation time needed to provide flood inundation estimates for fast-response analyses. This will be accomplished through the efficient use of multi-core, multi-processor computers coupled with an efficient domain-tracking algorithm, as well as an understanding of the impacts of grid resolution on model results.« less

Risk of inundation to coastal wetlands and soil organic carbon and organic nitrogen accounting in Louisiana, USA.

PubMed

Zhong, Biao; Xu, Y Jun

2011-10-01

Exceeding 1.2 million acres (4856 km(2)) since the 1930s, coastal wetland loss has been the most threatening environmental problem in Louisiana, United States. This study utilized high-resolution LiDAR (Light Detection and Ranging) and DEM (Digital Elevation Model) data sets to assess the risk of potential wetland loss due to future sea level rises, their spatial distribution, and the associated loss of soil organic carbon (SOC) and organic nitrogen (SON) estimated from the State Soil Geographic (STATSGO) Database and National Wetlands Inventory (NWI) digital data. Potential inundation areas were divided into five elevation scales: < 0 cm, 0-50 cm, 50-100 cm, 100-150 cm, and 150-200 cm above mean sea level. The study found that southeastern Louisiana on the Mississippi River Delta, specifically the Pontchartrain and Barataria Basins, are most vulnerable to sea-level rise induced inundation. Accordingly, approximately 42,264,600 t of SOC and 2,817,640 t of SON would be inundated by 2050 using an average wetland SOC density (203 t per hectare) for the inundation areas between 0 and 50 cm. The estimated annual SOC and SON loss from Louisiana's coast is 17% of annual organic carbon and 6-8% of annual organic nitrogen inputs from the Mississippi River.

Flood-inundation maps for the Leaf River at Hattiesburg, Mississippi

USGS Publications Warehouse

Storm, John B.

2012-01-01

Digital flood-inundation maps for a 1.7-mile reach of the Leaf River were developed by the U.S. Geological Survey (USGS) in cooperation with the City of Hattiesburg, City of Petal, Forrest County, Mississippi Emergency Management Agency, Mississippi Department of Homeland Security, and the Emergency Management District. The Leaf River study reach extends from just upstream of the U.S. Highway 11 crossing to just downstream of East Hardy/South Main Street and separates the cities of Hattiesburg and Petal, Mississippi. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water-surface elevations (stages) at the USGS streamgage at Leaf River at Hattiesburg, Mississippi (02473000). Current conditions at the USGS streamgage may be obtained through the National Water Information System Web site at http://waterdata.usgs.gov/ms/nwis/uv/?site_no=02473000&PARAmeter_cd=00065,00060. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood-warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often collocated at USGS streamgages. The forecasted peak-stage information, available on the AHPS Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at the Leaf River at Hattiesburg, Mississippi, streamgage and documented high-water marks from recent and historical floods. The hydraulic model was then used to determine 13 water-surface profiles for flood stages at 1.0-foot intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water-surface elevation at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model [derived from Light Detection and Ranging (LiDAR) data having a 0.6-foot vertical accuracy and 9.84-foot horizontal resolution] in order to delineate the area flooded at each 1-foot increment of stream stage. The availability of these maps, when combined with real-time stage information from USGS streamgages and forecasted stream stage from the NWS, provides emergency management personnel and residents with critical information during flood-response activities, such as evacuations and road closures, as well as for post-flood recovery efforts.

Chronic Inundation along the US Coastline: Where, When and How to Respond

NASA Astrophysics Data System (ADS)

Caldas, A.; Dahl, K. A.; Spanger-Siegfried, E.; Udvardy, S.

2017-12-01

The Union of Concerned Scientists conducted an analysis of exposure to chronic inundation along the US coastline, using three localized sea level rise projections—Highest, Intermediate-High and Intermediate-Low—drawn from the 2014 National Climate Assessment. Chronic inundation is defined as flooding of 10 percent or more of usable land area at least 26 times per year. The goal of the analysis was to identify not only which communities would face this type of disruptive inundation, but also when, and over how much of their area. By having a timeframe and different scenarios, communities can prepare according to the time they have, and their tolerance for risk. We also used the Social Vulnerability Index (SoVI) at the Census tract level to identify which of these communities might be differentially impacted because of socioeconomic factors. We found that, by 2035, 170 communities will be facing chronic inundation. That number jumps to between 490 and 670 by the end of the century, depending on the scenario. Under the two higher scenarios, more than half of communities facing chronic inundation by 2035 contain tracts with high socioeconomic vulnerability today. Using the Intermediate-Low scenario as a proxy for sea level rise were the long-term temperature goals outlined in the Paris Climate Agreement were met, we found that up to 380 communities could avoid chronic inundation this century. The results are accessible within an interactive online tool, which zooms in to street level, therefore providing specific information that communities, city planners, and elected officials need to plan and prepare. Preparatory measures could include defending against the sea, accommodating and learning to live with water, or retreating from areas that are too hard to live in anymore. Each of these measures has challenges, and communities will need to adopt a portfolio of actions to prepare and protect themselves. Depending on their inundation response time, communities might differ in the emphasis they place on different types of actions. Socioeconomically vulnerable communities will also need more resources and targeted policies in order to prepare for the impacts of sea level rise. Finally, we strongly advocate for emissions reductions on a global scale to reduce the pace of sea level rise.

Dam-breach analysis and flood-inundation mapping for Lakes Ellsworth and Lawtonka near Lawton, Oklahoma

USGS Publications Warehouse

Rendon, Samuel H.; Ashworth, Chad E.; Smith, S. Jerrod

2012-01-01

Dams provide beneficial functions such as flood control, recreation, and reliable water supplies, but they also entail risk: dam breaches and resultant floods can cause substantial property damage and loss of life. The State of Oklahoma requires each owner of a high-hazard dam, which the Federal Emergency Management Agency defines as dams for which failure or misoperation probably will cause loss of human life, to develop an emergency action plan specific to that dam. Components of an emergency action plan are to simulate a flood resulting from a possible dam breach and map the resulting downstream flood-inundation areas. The resulting flood-inundation maps can provide valuable information to city officials, emergency managers, and local residents for planning the emergency response if a dam breach occurs. Accurate topographic data are vital for developing flood-inundation maps. This report presents results of a cooperative study by the city of Lawton, Oklahoma, and the U.S. Geological Survey (USGS) to model dam-breach scenarios at Lakes Ellsworth and Lawtonka near Lawton and to map the potential flood-inundation areas of such dam breaches. To assist the city of Lawton with completion of the emergency action plans for Lakes Ellsworth and Lawtonka Dams, the USGS collected light detection and ranging (lidar) data that were used to develop a high-resolution digital elevation model and a 1-foot contour elevation map for the flood plains downstream from Lakes Ellsworth and Lawtonka. This digital elevation model and field measurements, streamflow-gaging station data (USGS streamflow-gaging station 07311000, East Cache Creek near Walters, Okla.), and hydraulic values were used as inputs for the dynamic (unsteady-flow) model, Hydrologic Engineering Center's River Analysis System (HEC-RAS). The modeled flood elevations were exported to a geographic information system to produce flood-inundation maps. Water-surface profiles were developed for a 75-percent probable maximum flood scenario and a sunny-day dam-breach scenario, as well as for maximum flood-inundation elevations and flood-wave arrival times for selected bridge crossings. Some areas of concern near the city of Lawton, if a dam breach occurs at Lakes Ellsworth or Lawtonka, include water treatment plants, wastewater treatment plants, recreational areas, and community-services offices.

Community exposure to tsunami hazards in California

USGS Publications Warehouse

Wood, Nathan J.; Ratliff, Jamie; Peters, Jeff

2013-01-01

Evidence of past events and modeling of potential events suggest that tsunamis are significant threats to low-lying communities on the California coast. To reduce potential impacts of future tsunamis, officials need to understand how communities are vulnerable to tsunamis and where targeted outreach, preparedness, and mitigation efforts may be warranted. Although a maximum tsunami-inundation zone based on multiple sources has been developed for the California coast, the populations and businesses in this zone have not been documented in a comprehensive way. To support tsunami preparedness and risk-reduction planning in California, this study documents the variations among coastal communities in the amounts, types, and percentages of developed land, human populations, and businesses in the maximum tsunami-inundation zone. The tsunami-inundation zone includes land in 94 incorporated cities, 83 unincorporated communities, and 20 counties on the California coast. According to 2010 U.S. Census Bureau data, this tsunami-inundation zone contains 267,347 residents (1 percent of the 20-county resident population), of which 13 percent identify themselves as Hispanic or Latino, 14 percent identify themselves as Asian, 16 percent are more than 65 years in age, 12 percent live in unincorporated areas, and 51 percent of the households are renter occupied. Demographic attributes related to age, race, ethnicity, and household status of residents in tsunami-prone areas demonstrate substantial range among communities that exceed these regional averages. The tsunami-inundation zone in several communities also has high numbers of residents in institutionalized and noninstitutionalized group quarters (for example, correctional facilities and military housing, respectively). Communities with relatively high values in the various demographic categories are identified throughout the report. The tsunami-inundation zone contains significant nonresidential populations based on 2011 economic data from Infogroup (2011), including 168,565 employees (2 percent of the 20-county labor force) at 15,335 businesses that generate approximately $30 billion in annual sales. Although the regional percentage of at-risk employees is low, certain communities, such as Belvedere, Alameda, and Crescent City, have high percentages of their local workforce in the tsunami-inundation zone. Employees in the tsunami-inundation zone are primarily in businesses associated with tourism (for example, accommodations, food services, and retail trade) and shipping (for example, transportation and warehousing, manufacturing, and wholesale trade), although the dominance of these sectors varies substantially among the 94 cities. Although the number of occupants is not known for each site, the tsunami-inundation zone contains numerous dependent-population facilities, such as schools and child daycare centers, which may have individuals with limited mobility. The tsunami-inundation zone includes a substantial number of facilities that provide community services, such as banks, religious organizations, and grocery stores, where local residents may be unaware of evacuation procedures if previous awareness efforts focused on home preparedness. There are also numerous recreational areas in the tsunami-inundation zone, such as amusement parks, marinas, city and county beaches, and State and national parks, which attract visitors who may not be aware of tsunami hazards or evacuation procedures. During peak summer months, estimated daily attendance at city and county beaches can be approximately six times larger than the total number of residents in the tsunami-inundation zone. Community exposure to tsunamis in California varies considerably—some communities may experience great losses that reflect only a small part of their community and others may experience relatively small losses that devastate them. Among 94 incorporated communities and the remaining unincorporated areas of the 20 coastal counties, the communities of Alameda, Oakland, Long Beach, Los Angeles, Huntington Beach, and San Diego have the highest number of people and businesses in the tsunami-inundation zone. The communities of Belvedere, Alameda, Crescent City, Emeryville, Seal Beach, and Sausalito have the highest percentages of people and businesses in this zone. On the basis of a composite index, the cities of Alameda, Belvedere, Crescent City, Emeryville, Oakland, and Long Beach have the highest combinations of the number and percentage of people and businesses in tsunami-prone areas.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khangaonkar, Tarang P.; Breithaupt, Stephen A.; Kristanovich, Felix C.

A hydrodynamic and hydrologic modeling analysis was conducted to evaluate the feasibility of restoring natural estuarine functions and tidal marine wetlands habitat in the Chinook River estuary, located near the mouth of the Columbia River in Washington. The reduction in salmonid populations is attributable primarily to the construction of a Highway 101 overpass across the mouth of the Chinook River in the early 1920s with a tide gate under the overpass. This construction, which was designed to eliminate tidal action in the estuary, has impeded the upstream passage of salmonids. The goal of the Chinook River Restoration Project is tomore » restore tidal functions through the estuary, by removing the tide gate at the mouth of the river, filling drainage ditches, restoring tidal swales, and reforesting riparian areas. The hydrologic model (HEC-HMS) was used to compute Chinook River and tributary inflows for use as input to the hydrodynamic model at the project area boundary. The hydrodynamic model (RMA-10) was used to generate information on water levels, velocities, salinity, and inundation during both normal tides and 100-year storm conditions under existing conditions and under the restoration alternatives. The RMA-10 model was extended well upstream of the normal tidal flats into the watershed domain to correctly simulate flooding and drainage with tidal effects included, using the wetting and drying schemes. The major conclusion of the hydrologic and hydrodynamic modeling study was that restoration of the tidal functions in the Chinook River estuary would be feasible through opening or removal of the tide gate. Implementation of the preferred alternative (removal of the tide gate, restoration of the channel under Hwy 101 to a 200-foot width, and construction of an internal levee inside the project area) would provide the required restorations benefits (inundation, habitat, velocities, and salinity penetration, etc.) and meet flood protection requirements. The alternative design included design of storage such that relatively little difference in the drainage or inundation upstream of Chinook River Valley Road would occur as a result of the proposed restoration activities.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khangaonkar, Tarang P.; Breithaupt, Stephen A.; Kristanovich, Felix C.

A hydrodynamic and hydrologic modeling analysis was conducted to evaluate the feasibility of restoring natural estuarine functions and tidal marine wetlands habitat in the Chinook River estuary, located near the mouth of the Columbia River in Washington. The reduction in salmonid populations is attributable primarily to the construction of a Highway 101 overpass across the mouth of the Chinook River in the early 1920s with a tide gate under the overpass. This construction, which was designed to eliminate tidal action in the estuary, has impeded the upstream passage of salmonids. The goal of the Chinook River Restoration Project is tomore » restore tidal functions through the estuary, by removing the tide gate at the mouth of the river, filling drainage ditches, restoring tidal swales, and reforesting riparian areas. The hydrologic model (HEC-HMS) was used to compute Chinook River and tributary inflows for use as input to the hydrodynamic model at the project area boundary. The hydrodynamic model (RMA-10) was used to generate information on water levels, velocities, salinity, and inundation during both normal tides and 100-year storm conditions under existing conditions and under the restoration alternatives. The RMA-10 model was extended well upstream of the normal tidal flats into the watershed domain to correctly simulate flooding anddrainage with tidal effects included, using the wetting and drying schemes. The major conclusion of the hydrologic and hydrodynamic modeling study was that restoration of the tidal functions in the Chinook River estuary would be feasible through opening or removal of the tide gate. Implementation of the preferred alternative (removal of the tide gate, restoration of the channel under Hwy 101 to a 200-foot width, and construction of an internal levee inside the project area) would provide the required restorations benefits (inundation, habitat, velocities, and salinity penetration, etc.) and meet flood protection requirements. The alternative design included design of storage such that relatively little difference in the drainage or inundation upstream of Chinook River Valley Road would occur as a result of the proposed restoration activities.« less

SPATIAL-TEMPORAL DISTRIBUTION OF WATERBORNE INFECTIOUS DISEASE RISK USING THE HYDRAULIC MODEL AND OUTPATIENT DATA

NASA Astrophysics Data System (ADS)

Amano, Ayako; Sakuma, Taisuke; Kazama, So

This study evaluated waterborne infectious diseases risk and incidence rate around Phonm Penh in Cambodia. We use the hydraulic flood simulation, coliform bacterium diffusion model, dose-response model and outpatient data for quantitative analysis. The results obtained are as follows; 1. The incidence (incidence rate) of diarrhea as water borne diseases risk is 0.14 million people (9%) in the inundation area. 2. The residents in the inundation area are exposed up to 4 times as high risk as daily mean calculated by the integrated model combined in the regional scale. 3.The infectious disease risk due to floods and inundation indicated is effective as an element to explain the risk. The scenario explains 34% number of patient estimated by the outpatient data.

Tsunami run-up and inundation along the coast of Sabah and Sarawak, Malaysia due to a potential Brunei submarine mass failure.

PubMed

Tan, Wai Kiat; Teh, Su Yean; Koh, Hock Lye

2017-07-01

Submarine landslides, also known as submarine mass failures (SMFs), are major natural marine disasters that could critically damage coastal facilities such as nuclear power plants and oil and gas platforms. It is therefore essential to investigate submarine landslides for potential tsunami hazard assessment. Three-dimensional seismic data from offshore Brunei have revealed a giant seabed mass deposited by a previous SMF. The submarine mass extends over 120 km from the continental slope of the Baram Canyon at 200 m water depth to the deep basin floor of the Northwest Borneo Trough. A suite of in-house two-dimensional depth-averaged tsunami simulation model TUNA (Tsunami-tracking Utilities and Application) is developed to assess the vulnerability of coastal communities in Sabah and Sarawak subject to potential SMF tsunami. The submarine slide is modeled as a rigid body moving along a planar slope with the center of mass motion parallel to the planar slope and subject to external forces due to added mass, gravity, and dissipation. The nonlinear shallow water equations are utilized to simulate tsunami propagation from deepwater up to the shallow offshore areas. A wetting-drying algorithm is used when a tsunami wave reaches the shoreline to compute run up of tsunami along the shoreline. Run-up wave height and inundation maps are provided for seven densely populated locations in Sabah and Sarawak to highlight potential risks at each location, subject to two scenarios of slide slopes: 2° and 4°. The first wave may arrive at Kudat as early as 0.4 h after the SMF, giving local communities little time to evacuate. Over a small area, maximum inundated depths reaching 20.3 m at Kudat, 26.1 m at Kota Kinabalu, and 15.5 m at Miri are projected, while the maximum inundation distance of 4.86 km is expected at Miri due to its low-lying coast. In view of the vulnerability of some locations to the SMF tsunami, it is important to develop and implement community resilience program to reduce the potential damage that could be inflicted by SMF tsunamis.

Modelling the ability of source control measures to reduce inundation risk in a community-scale urban drainage system

NASA Astrophysics Data System (ADS)

Mei, Chao; Liu, Jiahong; Wang, Hao; Shao, Weiwei; Xia, Lin; Xiang, Chenyao; Zhou, Jinjun

2018-06-01

Urban inundation is a serious challenge that increasingly confronts the residents of many cities, as well as policymakers, in the context of rapid urbanization and climate change worldwide. In recent years, source control measures (SCMs) such as green roofs, permeable pavements, rain gardens, and vegetative swales have been implemented to address flood inundation in urban settings, and proven to be cost-effective and sustainable. In order to investigate the ability of SCMs on reducing inundation in a community-scale urban drainage system, a dynamic rainfall-runoff model of a community-scale urban drainage system was developed based on SWMM. SCMs implementing scenarios were modelled under six design rainstorm events with return period ranging from 2 to 100 years, and inundation risks of the drainage system were evaluated before and after the proposed implementation of SCMs, with a risk-evaluation method based on SWMM and analytic hierarchy process (AHP). Results show that, SCMs implementation resulting in significantly reduction of hydrological indexes that related to inundation risks, range of reduction rates of average flow, peak flow, and total flooded volume of the drainage system were 28.1-72.1, 19.0-69.2, and 33.9-56.0 %, respectively, under six rainfall events with return periods ranging from 2 to 100 years. Corresponding, the inundation risks of the drainage system were significantly reduced after SCMs implementation, the risk values falling below 0.2 when the rainfall return period was less than 10 years. Simulation results confirm the effectiveness of SCMs on mitigating inundation, and quantified the potential of SCMs on reducing inundation risks in the urban drainage system, which provided scientific references for implementing SCMs for inundation control of the study area.

Flood-inundation maps for the Peckman River in the Townships of Verona, Cedar Grove, and Little Falls, and the Borough of Woodland Park, New Jersey, 2014

USGS Publications Warehouse

Niemoczynski, Michal J.; Watson, Kara M.

2016-10-19

Digital flood-inundation maps for an approximate 7.5-mile reach of the Peckman River in New Jersey, which extends from Verona Lake Dam in the Township of Verona downstream through the Township of Cedar Grove and the Township of Little Falls to the confluence with the Passaic River in the Borough of Woodland Park, were created by the U.S. Geological Survey (USGS) in cooperation with the New Jersey Department of Environmental Protection. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the probable areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Peckman River at Ozone Avenue at Verona, New Jersey (station number 01389534). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/.Flood profiles were simulated for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relations at USGS streamgages on the Peckman River at Ozone Avenue at Verona, New Jersey (station number 01389534) and the Peckman River at Little Falls, New Jersey (station number 01389550). The hydraulic model was then used to compute eight water-surface profiles for flood stages at 0.5-foot (ft) intervals ranging from 3.0 ft or near bankfull to 6.5 ft, which is approximately the highest recorded water level during the period of record (1979–2014) at USGS streamgage 01389534, Peckman River at Ozone Avenue at Verona, New Jersey. The simulated water-surface profiles were then combined with a geographic information system digital elevation model derived from light detection and ranging (lidar) data to delineate the area flooded at each water level.The availability of these maps along with Internet information regarding current stage from the USGS streamgage provides emergency management personnel and residents with information, such as estimates of inundation extents, based on water stage, that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Prediction of Tsunami Inundation in the City of Lisbon (portugal)

NASA Astrophysics Data System (ADS)

Baptista, M.; Miranda, J.; Omira, R.; Catalao Fernandes, J.

2010-12-01

Lisbon city is located inside the estuary of Tagus river, 20 km away from the Atlantic ocean. The city suffered great damage from tsunamis and its downtown was flooded at least twice in 1531 and 1755. Since the installation of the tide-gage network, in the area, three tsunamis caused by submarine earthquakes, were recorded in November 1941, February 1969 and May 1975. The most destructive tsunamis listed along Tagus Estuary are the 26th January 1531, a local tsunami event restricted to the Tagus Estuary, and the well known 1st November 1755 transoceanic event, both following highly destructive earthquakes, which deeply affected Lisbon. The economic losses due to the impact of the 1755 tsunami in one of Europe’s 18t century main harbor and commercial fleets were enormous. Since then the Tagus estuary suffered strong morphologic changes manly due to dredging works, construction of commercial and industrial facilities and recreational docks, some of them already projected to preserve Lisbon. In this study we present preliminary inundation maps for the Tagus estuary area in the Lisbon County, for conditions similar to the 1755 tsunami event, but using present day bathymetric and topographic maps. Inundation modelling is made using non linear shallow water theory and the numerical code is based upon COMCOT code. Nested grids resolutions used in this study are 800 m, 200 m and 50 m, respectively. The inundation is discussed in terms of flow depth, run up height, maximum inundation area and current flow velocity. The effects of estuary modifications on tsunami propagation are also investigated.

Development of Real-time Tsunami Inundation Forecast Using Ocean Bottom Tsunami Networks along the Japan Trench

NASA Astrophysics Data System (ADS)

Aoi, S.; Yamamoto, N.; Suzuki, W.; Hirata, K.; Nakamura, H.; Kunugi, T.; Kubo, T.; Maeda, T.

2015-12-01

In the 2011 Tohoku earthquake, in which huge tsunami claimed a great deal of lives, the initial tsunami forecast based on hypocenter information estimated using seismic data on land were greatly underestimated. From this lesson, NIED is now constructing S-net (Seafloor Observation Network for Earthquakes and Tsunamis along the Japan Trench) which consists of 150 ocean bottom observatories with seismometers and pressure gauges (tsunamimeters) linked by fiber optic cables. To take full advantage of S-net, we develop a new methodology of real-time tsunami inundation forecast using ocean bottom observation data and construct a prototype system that implements the developed forecasting method for the Pacific coast of Chiba prefecture (Sotobo area). We employ a database-based approach because inundation is a strongly non-linear phenomenon and its calculation costs are rather heavy. We prepare tsunami scenario bank in advance, by constructing the possible tsunami sources, and calculating the tsunami waveforms at S-net stations, coastal tsunami heights and tsunami inundation on land. To calculate the inundation for target Sotobo area, we construct the 10-m-mesh precise elevation model with coastal structures. Based on the sensitivities analyses, we construct the tsunami scenario bank that efficiently covers possible tsunami scenarios affecting the Sotobo area. A real-time forecast is carried out by selecting several possible scenarios which can well explain real-time tsunami data observed at S-net from tsunami scenario bank. An advantage of our method is that tsunami inundations are estimated directly from the actual tsunami data without any source information, which may have large estimation errors. In addition to the forecast system, we develop Web services, APIs, and smartphone applications and brush them up through social experiments to provide the real-time tsunami observation and forecast information in easy way to understand toward urging people to evacuate.

Flood regime and leaf fall determine soil inorganic nitrogen dynamics in semiarid riparian forests.

PubMed

Shah, J J Follstad; Dahm, C N

2008-04-01

Flow regulation has reduced the exchange of water, energy, and materials between rivers and floodplains, caused declines in native plant populations, and advanced the spread of nonnative plants. Naturalized flow regimes are regarded as a means to restore degraded riparian areas. We examined the effects of flood regime (short [SIFI] vs. long [LIFI] inter-flood interval) on plant community and soil inorganic nitrogen (N) dynamics in riparian forests dominated by native Populus deltoides var. wislizenii Eckenwalder (Rio Grande cottonwood) and nonnative Tamarix chinensis Lour. (salt cedar) along the regulated middle Rio Grande of New Mexico. The frequency of inundation (every 2-3 years) at SIFI sites better reflected inundation patterns prior to the closure of an upstream dam relative to the frequency of inundation at LIFI sites (> or =10 years). Riparian inundation at SIFI sites varied from 7 to 45 days during the study period (April 2001-July 2004). SIFI vs. LIFI sites had higher soil moisture but greater groundwater table elevation fluctuation in response to flooding and drought. Rates of net N mineralization were consistently higher at LIFI vs. SIFI sites, and soil inorganic N concentrations were greatest at sites with elevated leaf-litter production. Sites with stable depth to ground water (approximately 1.5 m) supported the greatest leaf-litter production. Reduced leaf production at P. deltoides SIFI sites was attributed to drought-induced recession of ground water and prolonged inundation. We recommend that natural resource managers and restoration practitioners (1) utilize naturalized flows that help maintain riparian groundwater elevations between 1 and 3 m in reaches with mature P. deltoides or where P. deltoides revegetation is desired, (2) identify areas that naturally undergo long periods of inundation and consider restoring these areas to seasonal wetlands, and (3) use native xeric-adapted riparian plants to revegetate LIFI and SIFI sites where groundwater elevations commonly drop below 3 m.

A framework for probabilistic pluvial flood nowcasting for urban areas

NASA Astrophysics Data System (ADS)

Ntegeka, Victor; Murla, Damian; Wang, Lipen; Foresti, Loris; Reyniers, Maarten; Delobbe, Laurent; Van Herk, Kristine; Van Ootegem, Luc; Willems, Patrick

2016-04-01

Pluvial flood nowcasting is gaining ground not least because of the advancements in rainfall forecasting schemes. Short-term forecasts and applications have benefited from the availability of such forecasts with high resolution in space (~1km) and time (~5min). In this regard, it is vital to evaluate the potential of nowcasting products for urban inundation applications. One of the most advanced Quantitative Precipitation Forecasting (QPF) techniques is the Short-Term Ensemble Prediction System, which was originally co-developed by the UK Met Office and Australian Bureau of Meteorology. The scheme was further tuned to better estimate extreme and moderate events for the Belgian area (STEPS-BE). Against this backdrop, a probabilistic framework has been developed that consists of: (1) rainfall nowcasts; (2) sewer hydraulic model; (3) flood damage estimation; and (4) urban inundation risk mapping. STEPS-BE forecasts are provided at high resolution (1km/5min) with 20 ensemble members with a lead time of up to 2 hours using a 4 C-band radar composite as input. Forecasts' verification was performed over the cities of Leuven and Ghent and biases were found to be small. The hydraulic model consists of the 1D sewer network and an innovative 'nested' 2D surface model to model 2D urban surface inundations at high resolution. The surface components are categorized into three groups and each group is modelled using triangular meshes at different resolutions; these include streets (3.75 - 15 m2), high flood hazard areas (12.5 - 50 m2) and low flood hazard areas (75 - 300 m2). Functions describing urban flood damage and social consequences were empirically derived based on questionnaires to people in the region that were recently affected by sewer floods. Probabilistic urban flood risk maps were prepared based on spatial interpolation techniques of flood inundation. The method has been implemented and tested for the villages Oostakker and Sint-Amandsberg, which are part of the larger city of Gent, Belgium. After each of the different above-mentioned components were evaluated, they were combined and tested for recent historical flood events. The rainfall nowcasting, hydraulic sewer and 2D inundation modelling and socio-economical flood risk results each could be partly evaluated: the rainfall nowcasting results based on radar data and rain gauges; the hydraulic sewer model results based on water level and discharge data at pumping stations; the 2D inundation modelling results based on limited data on some recent flood locations and inundation depths; the results for the socio-economical flood consequences of the most extreme events based on claims in the database of the national disaster agency. Different methods for visualization of the probabilistic inundation results are proposed and tested.

New insights of tsunami hazard from the 2011 Tohoku-oki event

USGS Publications Warehouse

Goto, K.; Chague-Goff, C.; Fujino, S.; Goff, J.; Jaffe, B.; Nishimura, Y.; Richmond, B.; Sugawara, D.; Szczucinski, W.; Tappin, D.R.; Witter, R.C.; Yulianto, E.

2011-01-01

We report initial results from our recent field survey documenting the inundation and resultant deposits of the 2011 Tohoku-oki tsunami from Sendai Plain, Japan. The tsunami inundated up to 4.5. km inland but the > 0.5 cm-thick sand deposit extended only 2.8. km (62% of the inundation distance). The deposit however continued as a mud layer to the inundation limit. The mud deposit contained high concentrations of water-leachable chloride and we conclude that geochemical markers and microfossil data may prove to be useful in identifying the maximum inundation limit of paleotsunamis that could extend well beyond any preserved sand layer. Our newly acquired data on the 2011 event suggest that previous estimates of paleotsunamis (e.g. 869 AD J??gan earthquake and tsunami) in this area have probably been underestimated. If the 2011 and 869 AD events are indeed comparable, the risk from these natural hazards in Japan is much greater than previously recognized. ?? 2011 Elsevier B.V.

Characterization of peak streamflows and flood inundation at selected areas in North Carolina following Hurricane Matthew, October 2016

USGS Publications Warehouse

Musser, Jonathan W.; Watson, Kara M.; Gotvald, Anthony J.

2017-05-05

The passage of Hurricane Matthew through central and eastern North Carolina during October 7–9, 2016, brought heavy rainfall, which resulted in major flooding. More than 15 inches of rain was recorded in some areas. More than 600 roads were closed, including Interstates 95 and 40, and nearly 99,000 structures were affected by floodwaters. Immediately following the flooding, the U.S. Geological Survey documented 267 high-water marks, of which 254 were surveyed. North Carolina Emergency Management documented and surveyed 353 high-water marks. Using a subset of these highwater marks, six flood-inundation maps were created for hard-hit communities. Digital datasets of the inundation areas, study reach boundary, and water-depth rasters are available for download. In addition, peak gage-height data, peak streamflow data, and annual exceedance probabilities (in percent) were determined for 24 U.S. Geological Survey streamgages located near the heavily flooded communities.

GLOFRIM - A globally applicable framework for integrated hydrologic-hydrodynamic inundation modelling

NASA Astrophysics Data System (ADS)

Hoch, J. M.; Neal, J. C.; Baart, F.; Van Beek, L. P.; Winsemius, H.; Bates, P. D.; Bierkens, M. F.

2017-12-01

Currently, many approaches to provide detailed flood hazard and risk estimates are built upon specific hydrologic or hydrodynamic model routines. By applying these routines in stand-alone mode important processes can however not accurately be described. For instance, global hydrologic models run at coarse spatial resolution, not supporting the detailed simulation of flood hazard. Hydrodynamic models excel in the computations of open water flow dynamics, but dependent on specific runoff or observed discharge as input. In most cases hydrodynamic models are forced at the boundaries and thus cannot account for water sources within the model domain, limiting the simulation of inundation dynamics to reaches fed by upstream boundaries. Recently, Hoch et al. (HESS, 2017) coupled PCR-GLOBWB (PCR) with the hydrodynamic model Delft3D Flexible Mesh (DFM). By means of the Basic Model Interface both models were connected on a cell-by-cell basis, allowing for spatially explicit coupling. Model results showed that discharge simulations can profit from model coupling compared to stand-alone runs. As model results of a coupled simulation depend on the quality of the models, it would be worthwhile to allow a suite of models to be coupled. To facilitate this, we present GLOFRIM, a globally applicable framework for integrated hydrologic-hydrodynamic inundation modelling. In the current version coupling between PCR and both DFM and LISFLOOD-FP (LFP) can be established (Hoch et al., GMDD, 2017). First results show that differences between both hydrodynamic models are present in the timing of peak discharge which is most likely due to differences in channel-floodplain interactions and bathymetry processing. Having benchmarked inundation extent, LFP and DFM agree for around half of the inundated area which is attributable to variations in grid size. Results also indicate that, despite using identical boundary conditions and forcing, the schematization itself as well as internal processes can still greatly influence results. In general, the application of GLOFRIM brings several advantages. For example, with PCR being a global model, it is possible to reduce the dependency of observation data for discharge boundaries, and benchmarking of hydrodynamic models is greatly facilitated by employing identical hydrologic forcing.

Analysis of Compound Water Hazard in Coastal Urbanized Areas under the Future Climate

NASA Astrophysics Data System (ADS)

Shibuo, Y.; Taniguchi, K.; Sanuki, H.; Yoshimura, K.; Lee, S.; Tajima, Y.; Koike, T.; Furumai, H.; Sato, S.

2017-12-01

Several studies indicate the increased frequency and magnitude of heavy rainfalls as well as the sea level rise under the future climate, which implies that coastal low-lying urbanized areas may experience increased risk against flooding. In such areas, where river discharge, tidal fluctuation, and city drainage networks altogether influence urban inundation, it is necessary to consider their potential interference to understand the effect of compound water hazard. For instance, pump stations cannot pump out storm water when the river water level is high, and in the meantime the river water level shall increase when it receives pumped water from cities. At the further downstream, as the tidal fluctuation regulates the water levels in the river, it will also affect the functionality of pump stations and possible inundation from rivers. In this study, we estimate compound water hazard in the coastal low-lying urbanized areas of the Tsurumi river basin under the future climate. We developed the seamlessly integrated river, sewerage, and coastal hydraulic model that can simulate river water levels, water flow in sewerage network, and inundation from the rivers and/or the coast to address the potential interference issue. As a forcing, the pseudo global warming method, which applies the changes in GCM anomaly to re-analysis data, is employed to produce ensemble typhoons to drive the seamlessly integrated model. The results show that heavy rainfalls caused by the observed typhoon generally become stronger under the pseudo global climate condition. It also suggests that the coastal low-lying areas become extensively inundated if the onset of river flooding and storm surge coincides.

A heterogeneous and parallel computing framework for high-resolution hydrodynamic simulations

NASA Astrophysics Data System (ADS)

Smith, Luke; Liang, Qiuhua

2015-04-01

Shock-capturing hydrodynamic models are now widely applied in the context of flood risk assessment and forecasting, accurately capturing the behaviour of surface water over ground and within rivers. Such models are generally explicit in their numerical basis, and can be computationally expensive; this has prohibited full use of high-resolution topographic data for complex urban environments, now easily obtainable through airborne altimetric surveys (LiDAR). As processor clock speed advances have stagnated in recent years, further computational performance gains are largely dependent on the use of parallel processing. Heterogeneous computing architectures (e.g. graphics processing units or compute accelerator cards) provide a cost-effective means of achieving high throughput in cases where the same calculation is performed with a large input dataset. In recent years this technique has been applied successfully for flood risk mapping, such as within the national surface water flood risk assessment for the United Kingdom. We present a flexible software framework for hydrodynamic simulations across multiple processors of different architectures, within multiple computer systems, enabled using OpenCL and Message Passing Interface (MPI) libraries. A finite-volume Godunov-type scheme is implemented using the HLLC approach to solving the Riemann problem, with optional extension to second-order accuracy in space and time using the MUSCL-Hancock approach. The framework is successfully applied on personal computers and a small cluster to provide considerable improvements in performance. The most significant performance gains were achieved across two servers, each containing four NVIDIA GPUs, with a mix of K20, M2075 and C2050 devices. Advantages are found with respect to decreased parametric sensitivity, and thus in reducing uncertainty, for a major fluvial flood within a large catchment during 2005 in Carlisle, England. Simulations for the three-day event could be performed on a 2m grid within a few hours. In the context of a rapid pluvial flood event in Newcastle upon Tyne during 2012, the technique allows simulation of inundation for a 31km2 of the city centre in less than an hour on a 2m grid; however, further grid refinement is required to fully capture important smaller flow pathways. Good agreement between the model and observed inundation is achieved for a variety of dam failure, slow fluvial inundation, rapid pluvial inundation, and defence breach scenarios in the UK.

Changes in community-level riparian plant traits over inundation gradients, Colorado River, Grand Canyon

USGS Publications Warehouse

McCoy-Sulentic, Miles; Kolb, Thomas; Merritt, David; Palmquist, Emily C.; Ralston, Barbara E.; Sarr, Daniel; Shafroth, Patrick B.

2017-01-01

Comparisons of community-level functional traits across environmental gradients have potential for identifying links among plant characteristics, adaptations to stress and disturbance, and community assembly. We investigated community-level variation in specific leaf area (SLA), plant mature height, seed mass, stem specific gravity (SSG), relative cover of C4 species, and total plant cover over hydrologic zones and gradients in years 2013 and 2014 in the riparian plant community along the Colorado River in the Grand Canyon. Vegetation cover was lowest in the frequently inundated active channel zone, indicating constraints on plant establishment and production by flood disturbance and anaerobic stress. Changes in trait values over hydrologic zones and inundation gradients indicate that frequently inundated plots exhibit a community-level ruderal strategy with adaptation to submergence (high SLA and low SSG, height, seed mass, C4 relative cover), whereas less frequently inundated plots exhibit adaptation to drought and infrequent flood disturbance (low SLA and high SSG, height, seed mass, C4 relative cover). Variation in traits not associated with inundation suggests niche differentiation and multiple modes of community assembly. The results enhance understanding of future responses of riparian communities of the Grand Canyon to anticipated drying and changes in hydrologic regime.

Automated quantification of surface water inundation in wetlands using optical satellite imagery

USGS Publications Warehouse

DeVries, Ben; Huang, Chengquan; Lang, Megan W.; Jones, John W.; Huang, Wenli; Creed, Irena F.; Carroll, Mark L.

2017-01-01

We present a fully automated and scalable algorithm for quantifying surface water inundation in wetlands. Requiring no external training data, our algorithm estimates sub-pixel water fraction (SWF) over large areas and long time periods using Landsat data. We tested our SWF algorithm over three wetland sites across North America, including the Prairie Pothole Region, the Delmarva Peninsula and the Everglades, representing a gradient of inundation and vegetation conditions. We estimated SWF at 30-m resolution with accuracies ranging from a normalized root-mean-square-error of 0.11 to 0.19 when compared with various high-resolution ground and airborne datasets. SWF estimates were more sensitive to subtle inundated features compared to previously published surface water datasets, accurately depicting water bodies, large heterogeneously inundated surfaces, narrow water courses and canopy-covered water features. Despite this enhanced sensitivity, several sources of errors affected SWF estimates, including emergent or floating vegetation and forest canopies, shadows from topographic features, urban structures and unmasked clouds. The automated algorithm described in this article allows for the production of high temporal resolution wetland inundation data products to support a broad range of applications.

Effect of Nearshore Islands on Tsunami Inundation in Shadow Zones

NASA Astrophysics Data System (ADS)

Goertz, J.; Kaihatu, J. M.; Kalligeris, N.; Lynett, P. J.; Synolakis, C.

2017-12-01

Field surveys performed in the wake of the 2010 Mentawai tsunami event have described the belief of local residents that offshore islands serve as possible tsunami sheltering mechanisms, reducing the corresponding inundation on beaches behind the islands, despite the fact that deduced inundation from debris lines show this to be in fact untrue (Hill et al. 2012). Recent numerical model studies (Stefanakis et al. 2014) have shown that inundation levels on beaches behind conical islands are indeed higher than they are on open coastlines. While work has been done on tsunami amplification on the lee side of islands (Briggs et al. 1995), no work has been done concerning tsunami inundation on beach areas behind the islands. A series of experiments to address this were conducted in the Directional Wave Basin (DWB) at the O.H. Hinsdale Wave Research Laboratory at Oregon State University in summer 2016. A series of four sheet metal islands (two with a full conical section, two truncated at the water line) were placed at varying distances from the toe of a 1/10 sloping beach. Incident wave conditions consisting of solitary waves and full-stroke "dam break" waves were run over the islands. Free surface elevations, velocities, and beach runup were measured, with the intent of determining relationships between the wave condition, the island geometry and distance from the beach, and the tsunami characteristics. A series of runup measurements from a particular set of experiments can be seen in Figure 1. Based on these preliminary analyses, it was determined that: A) inundation was always amplified behind the island relative to areas outside this shadow zone; and B) inundation was generally highest with the island closest to the beach, except in the case where the tsunami wave broke prior to reaching the island. In this latter scenario, the inundation behind the island increased with island distance from the beach. The development of relationships between the inundation levels, island geometry and distance, and wave conditions will be described. References: Briggs, M.J., et al. (1995), Pure Appl. Geophys., 144, 569-593. Hill, E.M., et al. (2012), J. Geophys. Res. - Sol. Ea., 117, B06402. Stefanakis, T.,et al. (2014), Proc. R. Soc. A, DOI: 10.1098/rspa.2014.0575.

Development of an Interactive Shoreline Management Tool for the Lower Wood River Valley, Oregon - Phase I: Stage-Volume and Stage-Area Relations

USGS Publications Warehouse

Haluska, Tana L.; Snyder, Daniel T.

2007-01-01

This report presents the parcel and inundation area geographic information system (GIS) layers for various surface-water stages. It also presents data tables containing the water stage, inundation area, and water volume relations developed from analysis of detailed land surface elevation derived from Light Detection and Ranging (LiDAR) data recently collected for the Wood River Valley at the northern margin of Agency Lake in Klamath County, Oregon. Former shoreline wetlands that have been cut off from Upper Klamath and Agency Lakes by dikes might in the future be reconnected to Upper Klamath and Agency Lakes by breaching the dikes. Issues of interest associated with restoring wetlands in this way include the area that will be inundated, the volume of water that may be stored, the change in wetland habitat, and the variation in these characteristics as surface-water stage is changed. Products from this analysis can assist water managers in assessing the effect of breaching dikes and changing surface-water stage. The study area is in the approximate former northern margins of Upper Klamath and Agency Lakes in the Wood River Valley.

Ohio River backwater flood-inundation maps for the Saline and Wabash Rivers in southern Illinois

USGS Publications Warehouse

Murphy, Elizabeth A.; Sharpe, Jennifer B.; Soong, David T.

2012-01-01

Digital flood-inundation maps for the Saline and Wabash Rivers referenced to elevations on the Ohio River in southern Illinois were created by the U.S. Geological Survey (USGS). The inundation maps, accessible through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Ohio River at Old Shawneetown, Illinois-Kentucky (station number 03381700). Current gage height and flow conditions at this USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?03381700. In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. That NWS forecasted peak-stage information, also shown on the Ohio River at Old Shawneetown inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, eight water-surface elevations were mapped at 5-foot (ft) intervals referenced to the streamgage datum ranging from just above the NWS Action Stage (31 ft) to above the maximum historical gage height (66 ft). The elevations of the water surfaces were compared to a Digital Elevation Model (DEM) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage heights from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Testing the skill of numerical hydraulic modeling to simulate spatiotemporal flooding patterns in the Logone floodplain, Cameroon

NASA Astrophysics Data System (ADS)

Fernández, Alfonso; Najafi, Mohammad Reza; Durand, Michael; Mark, Bryan G.; Moritz, Mark; Jung, Hahn Chul; Neal, Jeffrey; Shastry, Apoorva; Laborde, Sarah; Phang, Sui Chian; Hamilton, Ian M.; Xiao, Ningchuan

2016-08-01

Recent innovations in hydraulic modeling have enabled global simulation of rivers, including simulation of their coupled wetlands and floodplains. Accurate simulations of floodplains using these approaches may imply tremendous advances in global hydrologic studies and in biogeochemical cycling. One such innovation is to explicitly treat sub-grid channels within two-dimensional models, given only remotely sensed data in areas with limited data availability. However, predicting inundated area in floodplains using a sub-grid model has not been rigorously validated. In this study, we applied the LISFLOOD-FP hydraulic model using a sub-grid channel parameterization to simulate inundation dynamics on the Logone River floodplain, in northern Cameroon, from 2001 to 2007. Our goal was to determine whether floodplain dynamics could be simulated with sufficient accuracy to understand human and natural contributions to current and future inundation patterns. Model inputs in this data-sparse region include in situ river discharge, satellite-derived rainfall, and the shuttle radar topography mission (SRTM) floodplain elevation. We found that the model accurately simulated total floodplain inundation, with a Pearson correlation coefficient greater than 0.9, and RMSE less than 700 km2, compared to peak inundation greater than 6000 km2. Predicted discharge downstream of the floodplain matched measurements (Nash-Sutcliffe efficiency of 0.81), and indicated that net flow from the channel to the floodplain was modeled accurately. However, the spatial pattern of inundation was not well simulated, apparently due to uncertainties in SRTM elevations. We evaluated model results at 250, 500 and 1000-m spatial resolutions, and found that results are insensitive to spatial resolution. We also compared the model output against results from a run of LISFLOOD-FP in which the sub-grid channel parameterization was disabled, finding that the sub-grid parameterization simulated more realistic dynamics. These results suggest that analysis of global inundation is feasible using a sub-grid model, but that spatial patterns at sub-kilometer resolutions still need to be adequately predicted.

Flood-inundation maps for the Tippecanoe River near Delphi, Indiana

USGS Publications Warehouse

Menke, Chad D.; Bunch, Aubrey R.; Kim, Moon H.

2013-01-01

Digital flood-inundation maps for an 11-mile reach of the Tippecanoe River that extends from County Road W725N to State Road 18 below Oakdale Dam, Indiana (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at USGS streamgage 03333050, Tippecanoe River near Delphi, Ind. Current conditions at the USGS streamgages in Indiana may be obtained online at http://waterdata.usgs.gov/in/nwis/current/?type=flow. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, water-surface profiles were simulated for the stream reach by means of a hydraulic one-dimensional step-backwater model. The model was calibrated by using the most current stage-discharge relation at USGS streamgage 03333050, Tippecanoe River near Delphi, Ind., and USGS streamgage 03332605, Tippecanoe River below Oakdale Dam, Ind. The hydraulic model was then used to simulate 13 water-surface profiles for flood stages at 1-foot intervals reference to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. A flood inundation map was generated for each water-surface profile stage (13 maps in all) so that, for any given flood stage, users will be able to view the estimated area of inundation. The availability of these maps, along with current stage from USGS streamgages and forecasted stream stages from the NWS, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The morphological development of newly inundated intertidal areas: the mechanisms driving the early evolution of an estuarine environment designed and constructed by humans

NASA Astrophysics Data System (ADS)

Dale, Jonathan; Burgess, Heidi; Cundy, Andrew

2017-04-01

Intertidal saltmarsh and mudflat habitats are of global importance due to the ecosystem, economic and cultural services they provide. These services include wildlife habitat provision and species diversity, immobilisation of pollutants and protection from coastal flooding. Saltmarsh and mudflat environments are, however, being lost and degraded due to erosion caused by rising sea levels and increased storminess. These losses are exacerbated by anthropogenic influences including land reclamation, increased coastal development and the construction of coastal flood defences which prevent the landwards migration of saltmarsh and mudflat environments, resulting in coastal squeeze. To compensate for saltmarsh and mudflat losses areas of the coastal hinterland are being inundated by breaching defences and constructing new defences inland, thus extending or constructing new estuarine environments; a processes known as de-embankment or managed realignment. Morphological engineering and landscaping within managed realignment sites prior to site inundation varies depending on the aims of the scheme. However, there is a shortage of data on the morphological evolution within these sites post site inundation impeding the ability of coastal engineers to effectively design and construct future sites. To date there has been a focus on the colonisation of marine macro fauna and flora within newly inundated managed realignment sites, which can be relatively rapid and easily quantified. Little is known of the morphological evolution in response to altered sedimentary processes, its driving mechanisms and therefore the success and ecological sustainability of these sites. This study evaluates the post-inundation morphological development of the largest open coast managed realignment site in Europe, at Medmerry on the south coast of the United Kingdom. Inundated in September 2013, the Medmerry Managed Realignment Site consists of a mosaic of former agricultural land and areas of lower elevation excavated during site construction, drained by a series of natural and engineered channels. Results indicate different rates and patterns of sedimentation and resulting morphology across the site. Near the breach continuous sedimentation of > 15cm over a 1 year period was measured, compared to rhythmic periods of accretion and erosion inland. These variations have been related to site design, former land-use and different sediment sources. The evolution of developing creek networks, formed by pluvial action and sediment "piping", are controlled by unconformities found in the sub-surface sediment related to Holocene site evolution. Analysis of the sedimentary processes and subsequent morphological development of these areas provides a new insight into coastal and estuarine evolution in an anthropogenically designed and constructed estuarine environment.

Challenges and opportunities to improve understanding on wetland ecosystem and function at the local catchment scale: data fusion, data-model integration, and prediction uncertainty.

NASA Astrophysics Data System (ADS)

Yeo, I. Y.

2016-12-01

Wetlands are valuable landscape features that provide important ecosystem functions and services. The ecosystem processes in wetlands are highly dependent on the hydrology. However, hydroperiod (i.e., change dynamics in inundation extent) is highly variable spatially and temporarily, and extremely difficult to predict owing to the complexity in hydrological processes within wetlands and its interaction with surrounding areas. This study reports the challenges and progress in assessing the catchment scale benefits of wetlands to regulate hydrological regime and water quality improvement in agricultural watershed. A process-based watershed model, Soil and Water Assessment Tool (SWAT) was improved to simulate the cumulative impacts of wetlands on downstream. Newly developed remote sensing products from LiDAR intensity and time series Landsat records, which show the inter-annual changes in fraction inundation, were utilized to describe the change status of inundated areas within forested wetlands, develop spatially varying wetland parameters, and evaluate the predicted inundated areas at the landscape level. We outline the challenges on developing the time series inundation mapping products at a high spatial and temporal resolution and reconciling the catchment scale model with the moderate remote sensing products. We then highlight the importance of integrating spatialized information to model calibration and evaluation to address the issues of equi-finality and prediction uncertainty. This integrated approach was applied to the upper region of Choptank River Watershed, the agricultural watershed in the Coastal Plain of Chesapeake Bay Watershed (in US). In the Mid- Atlantic US, the provision of pollution regulation services provided by wetlands has been emphasized due to declining water quality within the Chesapeake Bay and watersheds, and the preservation and restoration of wetlands has become the top priority to manage nonpoint source water pollution.

Keeping it simple: Monitoring flood extent in large data-poor wetlands using MODIS SWIR data

NASA Astrophysics Data System (ADS)

Wolski, Piotr; Murray-Hudson, Mike; Thito, Kgalalelo; Cassidy, Lin

2017-05-01

Characterising inundation conditions for flood-pulsed wetlands is a critical first step towards assessment of flood risk as well as towards understanding hydrological dynamics that underlay their ecology and functioning. In this paper, we develop a series of inundation maps for the Okavango Delta, Botswana, based on the thresholding of the SWIR band (b7) MODIS MCD43A4 product. We show that in the Okavango Delta, SWIR is superior to other spectral bands or derived indices, and illustrate an innovative way of defining the spectral threshold used to separate inundated from dry land. The threshold is determined dynamically for each scene based on reflectances of training areas capturing end-members of the inundation spectrum. The method provides a very good accuracy and is suitable for automated processing.

Short-Term Summer Inundation as a Measure to Counteract Acidification in Rich Fens

PubMed Central

Mettrop, Ivan S.; Cusell, Casper; Kooijman, Annemieke M.; Lamers, Leon P. M.

2015-01-01

In regions with intensive agriculture, water level fluctuation in wetlands has generally become constricted within narrow limits. Water authorities are, however, considering the re-establishment of fluctuating water levels as a management tool in biodiverse, base-rich fens (‘rich fens’). This includes temporary inundation with surface water from ditches, which may play an important role in counteracting acidification in order to conserve and restore biodiversity. Inundation may result in an increased acid neutralizing capacity (ANC) for two reasons: infiltration of base-rich inundation water into peat soils, and microbial alkalinity generation under anaerobic conditions. The main objectives of this study were to test whether short-term (2 weeks) summer inundation is more effective than short-term winter inundation to restore the ANC in the upper 10 cm of non-floating peat soils, and to explain potential differences. Large-scale field experiments were conducted for five years in base-rich fens and Sphagnum-dominated poor fens. Winter inundation did not result in increased porewater ANC, because infiltration was inhibited in the waterlogged peat and evapotranspiration rates were relatively low. Also, low temperatures limit microbial alkalinity generation. In summer, however, when temperature and evapotranspiration rates are higher, inundation resulted in increased porewater Ca and HCO3 - concentrations, but only in areas with characteristic rich fen bryophytes. This increase was not only due to stronger infiltration into the soil, but also to higher microbial alkalinity generation under anaerobic conditions. In contrast, porewater ANC did not increase in Sphagnum-plots as a result of the ability of Sphagnum spp. to acidify their environment. In both rich and poor fens, flooding-induced P-mobilization remained sufficiently low to safeguard P-limited vegetation. NO3 - and NH4 + dynamics showed no considerable changes either. In conclusion, short-term summer inundation with base-rich and nutrient-poor surface water is considered beneficial in the management of non-floating rich fens, and much more effective than winter inundation. PMID:26637121

Predicting Near Real-Time Inundation Occurrence from Complimentary Satellite Microwave Brightness Temperature Observations

NASA Astrophysics Data System (ADS)

Fisher, C. K.; Pan, M.; Wood, E. F.

2017-12-01

Throughout the world, there is an increasing need for new methods and data that can aid decision makers, emergency responders and scientists in the monitoring of flood events as they happen. In many regions, it is possible to examine the extent of historical and real-time inundation occurrence from visible and infrared imagery provided by sensors such as MODIS or the Landsat TM; however, this is not possible in regions that are densely vegetated or are under persistent cloud cover. In addition, there is often a temporal mismatch between the sampling of a particular sensor and a given flood event, leading to limited observations in near real-time. As a result, there is a need for alternative methods that take full advantage of complimentary remotely sensed data sources, such as available microwave brightness temperature observations (e.g., SMAP, SMOS, AMSR2, AMSR-E, and GMI), to aid in the estimation of global flooding. The objective of this work was to develop a high-resolution mapping of inundated areas derived from multiple satellite microwave sensor observations with a daily temporal resolution. This system consists of first retrieving water fractions from complimentary microwave sensors (AMSR-2 and SMAP) which may spatially and temporally overlap in the region of interest. Using additional information in a Random Forest classifier, including high resolution topography and multiple datasets of inundated area (both historical and empirical), the resulting retrievals are spatially downscaled to derive estimates of the extent of inundation at a scale relevant to management and flood response activities ( 90m or better) instead of the relatively coarse resolution water fractions, which are limited by the microwave sensor footprints ( 5-50km). Here we present the training and validation of this method for the 2015 floods that occurred in Houston, Texas. Comparing the predicted inundation against historical occurrence maps derived from the Landsat TM record and MODIS imagery, we find good agreement for most areas and are able to provide a daily mapping given the increased temporal coverage. These results illustrate the feasibility of a near real-time inundation prediction system driven by multi-sensor satellite microwave observations, which can be extended to provide a daily estimate of global flooding.

Flood-inundation maps for the St. Marys River at Fort Wayne, Indiana

USGS Publications Warehouse

Menke, Chad D.; Kim, Moon H.; Fowler, Kathleen K.

2012-01-01

Digital flood-inundation maps for a 9-mile reach of the St. Marys River that extends from South Anthony Boulevard to Main Street at Fort Wayne, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the City of Fort Wayne. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site, depict estimates of the areal extent of flooding corresponding to selected water levels (stages) at the USGS streamgage 04182000 St. Marys River near Fort Wayne, Ind. Current conditions at the USGS streamgages in Indiana may be obtained from the National Water Information System: Web Interface. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system. The NWS forecasts flood hydrographs at many places that are often collocated at USGS streamgages. That forecasted peak-stage information, also available on the Internet, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, water-surface profiles were simulated for the stream reach by means of a hydraulic one-dimensional step-backwater model. The model was calibrated using the most current stage-discharge relation at the USGS streamgage 04182000 St. Marys River near Fort Wayne, Ind. The hydraulic model was then used to simulate 11 water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. A flood inundation map was generated for each water-surface profile stage (11 maps in all) so that for any given flood stage users will be able to view the estimated area of inundation. The availability of these maps along with current stage from USGS streamgages and forecasted stream stages from the NWS provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post flood recovery efforts.

Inundative release of Aphthona spp. flea beetles (Coleoptera: Chrysomlidae) as a biological "herbicide" on leafy spurge in riparian areas

Treesearch

R.A. Progar; G. Markin; J. Milan; T. Barbouletos; M.J. Rinella

2010-01-01

Inundative releases of beneficial insects are frequently used to suppress pest insects but not commonly attempted as a method of weed biological control because of the difficulty in obtaining the required large numbers of insects. The successful establishment of a flea beetle complex, mixed Aphthona lacertosa (Rosenhauer) and Aphthona...

Scenario Based Approach for Multiple Source Tsunami Hazard Assessment for Sines, Portugal

NASA Astrophysics Data System (ADS)

Wronna, Martin; Omira, Rachid; Baptista, Maria Ana

2015-04-01

In this paper, we present a scenario-based approach for tsunami hazard assessment for the city and harbour of Sines, Portugal one the test-sites of project ASTARTE. Sines holds one of the most important deep-water ports which contains oil-bearing, petrochemical, liquid bulk, coal and container terminals. The port and its industrial infrastructures are facing the ocean to the southwest facing the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, a total of five scenarios were selected to assess tsunami impact at the test site. These scenarios correspond to the worst-case credible scenario approach based upon the largest events of the historical and paleo tsunami catalogues. The tsunami simulations from the source area towards the coast is carried out using NSWING a Non-linear Shallow Water Model With Nested Grids. The code solves the non-linear shallow water equations using the discretization and explicit leap-frog finite difference scheme, in a Cartesian or Spherical frame. The initial sea surface displacement is assumed to be equal to the sea bottom deformation that is computed by Okada equations. Both uniform and non-uniform slip conditions are used. The presented results correspond to the models using non-uniform slip conditions. In this study, the static effect of tides is analysed for three different tidal stages MLLW (mean lower low water) MSL (mean sea level) and MHHW (mean higher high water). For each scenario, inundation is described by maximum values of wave height, flow depth, drawdown, run-up and inundation distance. Synthetic waveforms are computed at virtual tide gages at specific locations outside and inside the harbour. The final results consist of Aggregate Scenario Maps presented for the different inundation parameters. This work is funded by ASTARTE - Assessment, Strategy And Risk Reduction for Tsunamis in Europe - FP7-ENV2013 6.4-3, Grant 603839

Use of map analysis to elucidate flooding in an Australian Riparian River Red Gum Forest

NASA Astrophysics Data System (ADS)

Bren, L. J.; O'Neill, I. C.; Gibbs, N. L.

1988-07-01

Red gum (Eucalyptus camaldulensis) forests occur on extensive floodplains along the river Murray in Australia. This type of forest is unusual because of its high quality in a semiarid area, the absence of woody species other than red gum, and its survival on a deep, intractable, swelling clay soil of depths exceeding 20 m. This soil probably acts as an aquiclude. The forests require flooding to thrive and regenerate. For many years there has been speculation that irrigation regulation of the river was reducing forest flooding. A grid cell analysis of flood maps of areas flooded over a period of 22 years showed that vegetation communities and forest site quality were statistically related to the flood frequencies of sites. The percentage of forest inundated was dependent on the peak daily flow during the period of inundation. A historical analysis of the estimated percentage of forest inundated showed a substantial influence of river regulation on both timing and extent of inundation. Estimates of historical floodings showed that the environment is one that changes rapidly from wetland to dry land. Although not without limitations, the analysis produced information not available from other sources.

Study on the water related disaster risks using the future socio-economic scenario in Asia

NASA Astrophysics Data System (ADS)

Kiguchi, M.; Hatono, M.; Ikeuchi, H.; Nakamura, S.; Hirabayashi, Y.; Kanae, S.; Oki, T.

2014-12-01

In this study, flood risks in the present and the end of the 21st century in Asia are estimated using a future socio-economic scenario. Using the runoff data of 7 GCMs (RCP 8.5) of CMIP5, the river discharge, inundation area, and inundation depth are calculated for the assessment of flood risk. Finally, the flood risk is estimated using a function of damage. The flood frequency in the end of the 21st century in Asia tends to increase. Inundation area in Japan, Taiwan, and Kyrgyz is almost unchanged. At the same time, that in Sri Lanka, Bangladesh, Laos, and Myanmar reached about 1.4-1.6 times compared to present. Damage cost is largely influenced by economic growth, however, we show that it is important that we distinguish the influence of climate change from economic development and evaluate it when we think about an adaptation.

Environmental drivers of denitrification rates and denitrifying gene abundances in channels and riparian areas

NASA Astrophysics Data System (ADS)

Tomasek, Abigail; Kozarek, Jessica L.; Hondzo, Miki; Lurndahl, Nicole; Sadowsky, Michael J.; Wang, Ping; Staley, Christopher

2017-08-01

Intensive agriculture in the Midwestern United States contributes to excess nitrogen in surface water and groundwater, negatively affecting human health and aquatic ecosystems. Complete denitrification removes reactive nitrogen from aquatic environments and releases inert dinitrogen gas. We examined denitrification rates and the abundances of denitrifying genes and total bacteria at three sites in an agricultural watershed and in an experimental stream in Minnesota. Sampling was conducted along transects with a gradient from always inundated (in-channel), to periodically inundated, to noninundated conditions to determine how denitrification rates and gene abundances varied from channels to riparian areas with different inundation histories. Results indicate a coupling between environmental parameters, gene abundances, and denitrification rates at the in-channel locations, and limited to no coupling at the periodically inundated and noninundated locations, respectively. Nutrient-amended potential denitrification rates for the in-channel locations were significantly correlated (α = 0.05) with five of six measured denitrifying gene abundances, whereas the periodically inundated and noninundated locations were each only significantly correlated with the abundance of one denitrifying gene. These results suggest that DNA-based analysis of denitrifying gene abundances alone cannot predict functional responses (denitrification potential), especially in studies with varying hydrologic regimes. A scaling analysis was performed to develop a predictive functional relationship relating environmental parameters to denitrification rates for in-channel locations. This method could be applied to other geographic and climatic regions to predict the occurrence of denitrification hot spots.

Interactive Mapping of Inundation Metrics Using Cloud Computing for Improved Floodplain Conservation and Management

NASA Astrophysics Data System (ADS)

Bulliner, E. A., IV; Lindner, G. A.; Bouska, K.; Paukert, C.; Jacobson, R. B.

2017-12-01

Within large-river ecosystems, floodplains serve a variety of important ecological functions. A recent survey of 80 managers of floodplain conservation lands along the Upper and Middle Mississippi and Lower Missouri Rivers in the central United States found that the most critical information needed to improve floodplain management centered on metrics for characterizing depth, extent, frequency, duration, and timing of inundation. These metrics can be delivered to managers efficiently through cloud-based interactive maps. To calculate these metrics, we interpolated an existing one-dimensional hydraulic model for the Lower Missouri River, which simulated water surface elevations at cross sections spaced (<1 km) to sufficiently characterize water surface profiles along an approximately 800 km stretch upstream from the confluence with the Mississippi River over an 80-year record at a daily time step. To translate these water surface elevations to inundation depths, we subtracted a merged terrain model consisting of floodplain LIDAR and bathymetric surveys of the river channel. This approach resulted in a 29000+ day time series of inundation depths across the floodplain using grid cells with 30 m spatial resolution. Initially, we used these data on a local workstation to calculate a suite of nine spatially distributed inundation metrics for the entire model domain. These metrics are calculated on a per pixel basis and encompass a variety of temporal criteria generally relevant to flora and fauna of interest to floodplain managers, including, for example, the average number of days inundated per year within a growing season. Using a local workstation, calculating these metrics for the entire model domain requires several hours. However, for the needs of individual floodplain managers working at site scales, these metrics may be too general and inflexible. Instead of creating a priori a suite of inundation metrics able to satisfy all user needs, we present the usage of Google's cloud-based Earth Engine API to allow users to define and query their own inundation metrics from our dataset and produce maps nearly instantaneously. This approach allows users to select the time periods and inundation depths germane to managing local species, potentially facilitating conservation of floodplain ecosystems.

Using NOAA AVHRR data to assess flood damage in China.

PubMed

Wang, Quan; Watanabe, Masataka; Hayashi, Seiji; Murakami, Shogo

2003-03-01

The article used two NOAA-14 Advanced Very High Resolution Radiometer (AVHRR) datasets to assess flood damage in the middle and lower reaches of China's Changjiang River (Yangtze River) in 1998. As the AVHRR is an optical sensor, it cannot penetrate the clouds that frequently cover the land during the flood season, and this technology is greatly limited in flood monitoring. However the widely used normalized difference vegetation index (NDVI) can be used to monitor flooding, since water has a much lower NDVI value than other surface features. Though many factors other than flooding (e.g. atmospheric conditions, different sun-target-satellite angles, and cloud) can change NDVI values, inundated areas can be distinguished from other types of ground cover by changes in the NDVI value before and after the flood after eliminating the effects of other factors on NDVI. AVHRR data from 26 May and 22 August, 1998 were selected to represent the ground conditions before and after flooding. After accurate geometric correction by collecting GCPs, and atmospheric and angular corrections by using the 6S code, NDVI values for both days and their differences were calculated for cloud-free pixels. The difference in the NDVI values between these two times, together with the NDVI values and a land-use map, were used to identify inundated areas and to assess the area lost to the flood. The results show a total of 358,867 ha, with 207,556 ha of cultivated fields (paddy and non-irrigated field) inundated during the flood of 1998 in the middle and lower reaches of the Changjiang River Catchment; comparing with the reported total of 321,000 and 197,000 ha, respectively. The discrimination accuracy of this method was tested by comparing the results from two nearly simultaneous sets of remote-sensing data (NOAA's AVHRR data from 10 September, 1998, and JERS-1 synthetic aperture radar (SAR) data from 11 September, 1998, with a lag of about 18.5 hr) over a representative flooded region in the study area. The results showed that 67.26% of the total area identified as inundated using the NOAA data was also identified as inundated using the SAR data.

Coastal inundation risk assessment due to subsidence and sea level rise in a Mediterranean alluvial plain (Volturno coastal plain - southern Italy)

NASA Astrophysics Data System (ADS)

Ciro Aucelli, Pietro Patrizio; Di Paola, Gianluigi; Incontri, Pietro; Rizzo, Angela; Vilardo, Giuseppe; Benassai, Guido; Buonocore, Berardino; Pappone, Gerardo

2017-11-01

Interdisciplinary studies of the last years highlight that the Italian coasts are significantly subject to retreat and to inundation by sea ingression due to natural and anthropic causes. In this study, the effects of future relative sea level have been evaluated for the Volturno River Plain, one of the widest coastal plain in southern Italy. The plain is characterized by high economical and ecological value, for the presence of farm activities, tourist structures and wetland protected zones. The study area is potentially prone to coastal flooding due to its very low topography and because it is affected by a severe subsidence, which emphasize the local effect of sea level rise due to the ongoing climate changes. In accordance with the guidelines of the MEDFLOOD project, the areas prone to inundation in the years 2065 and 2100 have been evaluated by comparing the future topographical information and expected relative sea level scenarios. The local Vertical Ground Displacements have been derived by PS-InSAR processing data whilst the mean values of the scenarios RCP 2.6 and RCP 8.5 provided by the IPCC (2014) have been used as future sea level projections in 2065 and 2100. The PS-InSar data elaboration shows that the area affected by subsidence corresponds to 35% of the Volturno plain and that the annual rate of the phenomenon ranges between -1 and -25 mm/yr. The inundation analysis, based on the classification of the areas in four hazard classes, indicates that in 2065 the zones located below the sea level will increase approximately of 50% respect to the present conditions, while between 2065 and 2100 the increase can be at least of 60% (IPCC, RCP 8.5 scenarios). Considering the socio-economical and ecological exposure, evaluated following the EUROSION project guidelines, the coastal flooding risk maps have been produced. Almost 8.2 km2 and 14.4 km2 of the investigated area has to be considered subject to very high marine inundation risk in 2065 and 2100, respectively.

Modeling a Glacial Lake Outburst Flood Process Chain: The Case of Lake Palcacocha and Huaraz, Peru

NASA Astrophysics Data System (ADS)

Chisolm, Rachel; Somos-Valenzuela, Marcelo; Rivas Gomez, Denny; McKinney, Daene C.; Portocarrero Rodriguez, Cesar

2016-04-01

One of the consequences of recent glacier recession in the Cordillera Blanca, Peru, is the risk of Glacial Lake Outburst Floods (GLOFs) from lakes that have formed at the base of retreating glaciers. GLOFs are often triggered by avalanches falling into glacial lakes, initiating a chain of processes that may culminate in significant inundation and destruction downstream. This paper presents simulations of all of the processes involved in a potential GLOF originating from Lake Palcacocha, the source of a previously catastrophic GLOF on December 13, 1941, 1800 people in the city of Huaraz, Peru. The chain of processes simulated here includes: (1) avalanches above the lake; (2) lake dynamics resulting from the avalanche impact, including wave generation, propagation, and run-up across lakes; (3) terminal moraine overtopping and dynamic moraine erosion simulations to determine the possibility of breaching; (4) flood propagation along downstream valleys; and (5) inundation of populated areas. The results of each process feed into simulations of subsequent processes in the chain, finally resulting in estimates of inundation in the city of Huaraz. The results of the inundation simulations were converted into flood intensity and hazard maps (based on an intensity-likelihood matrix) that may be useful for city planning and regulation. Three avalanche events with volumes ranging from 0.5-3 x 106 m3 were simulated, and two scenarios of 15 m and 30 m lake lowering were simulated to assess the potential of mitigating the hazard level in Huaraz. For all three avalanche events, three-dimensional hydrodynamic models show large waves generated in the lake from the impact resulting in overtopping of the damming-moraine. Despite very high discharge rates (up to 63.4 x 103 m3/s), the erosion from the overtopping wave did not result in failure of the damming-moraine when simulated with a hydro-morphodynamic model using excessively conservative soil characteristics that provide very little erosion resistance. With the current lake level, all three avalanche events result in inundation in Huaraz, and the resulting hazard map shows a total affected area of 2.01 km2, most of which is in the high-hazard category. Lowering the lake has the potential to reduce the affected area by up to 35% resulting in a smaller portion of the inundated area in the high-hazard category.

Nowcasting, forecasting and hindcasting Harvey and Irma inundation in near-real time using a continental 2D hydrodynamic model

NASA Astrophysics Data System (ADS)

Sampson, C. C.; Wing, O.; Quinn, N.; Smith, A.; Neal, J. C.; Schumann, G.; Bates, P.

2017-12-01

During an ongoing natural disaster data are required on: (1) the current situation (nowcast); (2) its likely immediate evolution (forecast); and (3) a consistent view post-event of what actually happened (hindcast or reanalysis). We describe methods used to achieve all three tasks for flood inundation during the Harvey and Irma events using a continental scale 2D hydrodynamic model (Wing et al., 2017). The model solves the local inertial form of the Shallow Water equations over a regular grid of 1 arcsecond ( 30m). Terrain data are taken from the USGS National Elevation Dataset with known flood defences represented using the U.S. Army Corps of Engineers National Levee Dataset. Channels are treated as sub-grid scale features using the HydroSHEDS global hydrography data set. The model is driven using river flows, rainfall and coastal water levels. It simulates river flooding in basins > 50 km2, and fluvial and coastal flooding everywhere. Previous wide area validation tests show this model to be capable of matching FEMA maps and USGS local models built with bespoke data with hit rates of 86% and 92% respectively (Wing et al., 2017). Boundary conditions were taken from NOAA QPS data to produce nowcast and forecast simulations in near real time, before updating with NOAA observations to produce the hindcast. During the event simulation results were supplied to major insurers and multi-nationals who used them to estimate their likely capital exposure and to mitigate flood damage to their infrastructure whilst the event was underway. Simulations were validated against modelled flood footprints computed by FEMA and USACE, and composite satellite imagery produced by the Dartmouth Flood Observatory. For the Harvey event, hit rates ranged from 60-84% against these data sources, but a lack of metadata meant it was difficult to perform like-for-like comparisons. The satellite data also appeared to miss known flooding in urban areas that was picked up in the models. Despite these limitations, the validation was able to pick our areas, notably along the Colorado River near Houston, where our model under-performed and identify areas for future development. The study shows that high resolution near real-time inundation predictions over very large areas during complex events with multiple flood drivers are now a reality.

Dam-breach analysis and flood-inundation mapping for selected dams in Oklahoma City, Oklahoma, and near Atoka, Oklahoma

USGS Publications Warehouse

Shivers, Molly J.; Smith, S. Jerrod; Grout, Trevor S.; Lewis, Jason M.

2015-01-01

Digital-elevation models, field survey measurements, hydraulic data, and hydrologic data (U.S. Geological Survey streamflow-gaging stations North Canadian River below Lake Overholser near Oklahoma City, Okla. [07241000], and North Canadian River at Britton Road at Oklahoma City, Okla. [07241520]), were used as inputs for the one-dimensional dynamic (unsteady-flow) models using Hydrologic Engineering Centers River Analysis System (HEC–RAS) software. The modeled flood elevations were exported to a geographic information system to produce flood-inundation maps. Water-surface profiles were developed for a 75-percent probable maximum flood dam-breach scenario and a sunny-day dam-breach scenario, as well as for maximum flood-inundation elevations and flood-wave arrival times at selected bridge crossings. Points of interest such as community-services offices, recreational areas, water-treatment plants, and wastewater-treatment plants were identified on the flood-inundation maps.

The use of cartographic modeling to assess the impacts of coastal flooding: a case study of Port Said Governorate, Egypt.

PubMed

Abou Samra, Rasha M

2017-09-01

Low-set coastal areas are expected to aggravate inundation on account of sea level rise (SLR). The present study is planned to appraise the impacts of coastal flooding in Port Said city, Egypt by using remote sensing, GIS, and cartographic modeling techniques. To accomplish this scope, Landsat 8-OLI image dated 2016 and SRTM 1Arc-Second Digital Elevation Model (DEM) data were used. Landsat image was classified into seven land use and land cover (LULC) classes by using remote sensing and GIS's software. Different inundation scenarios 1.0, 2.0, and 3.0-m coastal elevation were used to figure the influence of SLR on the study area. Estimation of potential losses under SLR was made by overlaying the expected scenarios on land use. The inundation areas under the expected SLR scenarios of 1.0, 2.0, and 3.0 m were estimated at 827.49, 1072.67, and 1179.41 km 2 , respectively. In conclusion, this study demonstrated that expected coastal flooding scenarios will lead up to serious impacts on LULC classes and coastal features in the study area.

Two-Dimensional Flood-Inundation Model of the Flint River at Albany, Georgia

USGS Publications Warehouse

Musser, Jonathan W.; Dyar, Thomas R.

2007-01-01

Potential flow characteristics of future flooding along a 4.8-mile reach of the Flint River in Albany, Georgia, were simulated using recent digital-elevation-model data and the U.S. Geological Survey finite-element surface-water modeling system for two-dimensional flow in the horizontal plane (FESWMS-2DH). Simulated inundated areas, in 1-foot (ft) increments, were created for water-surface altitudes at the Flint River at Albany streamgage (02352500) from 192.5-ft altitude with a flow of 123,000 cubic feet per second (ft3/s) to 179.5-ft altitude with a flow of 52,500 ft3/s. The model was calibrated to match actual floods during July 1994 and March 2005 and Federal Emergency Management Administration floodplain maps. Continuity checks of selected stream profiles indicate the area near the Oakridge Drive bridge had lower velocities than other areas of the Flint River, which contributed to a rise in the flood-surface profile. The modeled inundated areas were mapped onto monochrome orthophoto imagery for use in planning for future floods. As part of a cooperative effort, the U.S. Geological Survey, the City of Albany, and Dougherty County, Georgia, conducted this study.

Inundative release of Aphthona spp. flea beetles (Coleoptera: Chrysomelidae) as a biological "herbicide" on leafy spurge in riparian areas

Treesearch

R. A. Progar; G. Markin; J. Milan; T. Barbouletos; M. J. Rinella

2010-01-01

Inundative releases of beneficial insects are frequently used to suppress pest insects but not commonly attempted as a method of weed biological control because of the difficulty in obtaining the required large numbers of insects. The successful establishment of a flea beetle complex, mixed Aphthona lacertosa (Rosenhauer) and Aphthona nigriscutus Foundras (87 and 13%,...

Inundative release of Aphthona spp. flea beetles (Coleoptera: Chrysomelidae) as a biological "herbicide" on leafy spurge (Euphorbia esula) in riparian areas

Treesearch

R. A. Progar; G. P. Markin; J. Milan; T. Barbouletos; M. J. Rinella

2013-01-01

Inundative releases of beneficial insects are frequently used to suppress pest insects, but not commonly attempted as a method of weed biological control because of the difficulty in obtaining the required large numbers of insects. The successful establishment of a flea beetle complex, mixed Aphthona lacertosa Rosenhauer and A. nigriscutus Foudras (87% and 13%,...

A first large-scale flood inundation forecasting model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schumann, Guy J-P; Neal, Jeffrey C.; Voisin, Nathalie

2013-11-04

At present continental to global scale flood forecasting focusses on predicting at a point discharge, with little attention to the detail and accuracy of local scale inundation predictions. Yet, inundation is actually the variable of interest and all flood impacts are inherently local in nature. This paper proposes a first large scale flood inundation ensemble forecasting model that uses best available data and modeling approaches in data scarce areas and at continental scales. The model was built for the Lower Zambezi River in southeast Africa to demonstrate current flood inundation forecasting capabilities in large data-scarce regions. The inundation model domainmore » has a surface area of approximately 170k km2. ECMWF meteorological data were used to force the VIC (Variable Infiltration Capacity) macro-scale hydrological model which simulated and routed daily flows to the input boundary locations of the 2-D hydrodynamic model. Efficient hydrodynamic modeling over large areas still requires model grid resolutions that are typically larger than the width of many river channels that play a key a role in flood wave propagation. We therefore employed a novel sub-grid channel scheme to describe the river network in detail whilst at the same time representing the floodplain at an appropriate and efficient scale. The modeling system was first calibrated using water levels on the main channel from the ICESat (Ice, Cloud, and land Elevation Satellite) laser altimeter and then applied to predict the February 2007 Mozambique floods. Model evaluation showed that simulated flood edge cells were within a distance of about 1 km (one model resolution) compared to an observed flood edge of the event. Our study highlights that physically plausible parameter values and satisfactory performance can be achieved at spatial scales ranging from tens to several hundreds of thousands of km2 and at model grid resolutions up to several km2. However, initial model test runs in forecast mode revealed that it is crucial to account for basin-wide hydrological response time when assessing lead time performances notwithstanding structural limitations in the hydrological model and possibly large inaccuracies in precipitation data.« less

Identification of erosional and inundation hazard zones in Ken-Betwa river linking area, India, using remote sensing and GIS.

PubMed

Avtar, Ram; Singh, Chander Kumar; Shashtri, Satayanarayan; Mukherjee, Saumitra

2011-11-01

Ken-Betwa river link is one of the pilot projects of the Inter Linking of Rivers program of Government of India in Bundelkhand Region. It will connect the Ken and Betwa rivers through a system of dams, reservoirs, and canals to provide storage for excess rainfall during the monsoon season and avoid floods. The main objective of this study is to identify erosional and inundation prone zones of Ken-Betwa river linking site in India using remote sensing and geographic information system tools. In this study, Landsat Thematic Mapper data of year 2005, digital elevation model from the Shuttle Radar Topographic Mission, and other ancillary data were analyzed to create various thematic maps viz. geomorphology, land use/land cover, NDVI, geology, soil, drainage density, elevation, slope, and rainfall. The integrated thematic maps were used for hazard zonation. This is based on categorizing the different hydrological and geomorphological processes influencing the inundation and erosion intensity. Result shows that the southern part of the study area which lies in Panna district of Madhya Pradesh, India, is more vulnerable than the other areas.

Characteristics of peak streamflows and extent of inundation in areas of West Virginia and southwestern Virginia affected by flooding, June 2016

USGS Publications Warehouse

Austin, Samuel H.; Watson, Kara M.; Lotspeich, R. Russell; Cauller, Stephen J.; White , Jeremy S.; Wicklein, Shaun M.

2017-11-17

Heavy rainfall occurred across central and southern West Virginia in June 2016 as a result of repeated rounds of torrential thunderstorms. The storms caused major flooding and flash flooding in central and southern West Virginia with Kanawha, Fayette, Nicholas, and Greenbrier Counties among the hardest hit. Over the duration of the storms, from 8 to 9.37 inches of rain was reported in areas in Greenbrier County. Peak streamflows were the highest on record at 7 locations, and streamflows at 18 locations ranked in the top five for the period of record at U.S. Geological Survey streamflow-gaging stations used in this study. Following the storms, U.S. Geological Survey hydrographers identified and documented 422 high-water marks in West Virginia, noting location and height of the water above land surface. Many of these high-water marks were used to create flood-inundation maps for selected communities of West Virginia that experienced flooding in June 2016. Digital datasets of the inundation areas, mapping boundaries, and water depth rasters are available online.

Simulated tsunami inundation for a range of Cascadia megathrust earthquake scenarios at Bandon, Oregon, USA

USGS Publications Warehouse

Witter, Robert C.; Zhang, Yinglong J.; Wang, Kelin; Priest, George R.; Goldfinger, Chris; Stimely, Laura; English, John T.; Ferro, Paul A.

2013-01-01

Characterizations of tsunami hazards along the Cascadia subduction zone hinge on uncertainties in megathrust rupture models used for simulating tsunami inundation. To explore these uncertainties, we constructed 15 megathrust earthquake scenarios using rupture models that supply the initial conditions for tsunami simulations at Bandon, Oregon. Tsunami inundation varies with the amount and distribution of fault slip assigned to rupture models, including models where slip is partitioned to a splay fault in the accretionary wedge and models that vary the updip limit of slip on a buried fault. Constraints on fault slip come from onshore and offshore paleoseismological evidence. We rank each rupture model using a logic tree that evaluates a model’s consistency with geological and geophysical data. The scenarios provide inputs to a hydrodynamic model, SELFE, used to simulate tsunami generation, propagation, and inundation on unstructured grids with <5–15 m resolution in coastal areas. Tsunami simulations delineate the likelihood that Cascadia tsunamis will exceed mapped inundation lines. Maximum wave elevations at the shoreline varied from ∼4 m to 25 m for earthquakes with 9–44 m slip and Mw 8.7–9.2. Simulated tsunami inundation agrees with sparse deposits left by the A.D. 1700 and older tsunamis. Tsunami simulations for large (22–30 m slip) and medium (14–19 m slip) splay fault scenarios encompass 80%–95% of all inundation scenarios and provide reasonable guidelines for land-use planning and coastal development. The maximum tsunami inundation simulated for the greatest splay fault scenario (36–44 m slip) can help to guide development of local tsunami evacuation zones.

Method for estimating potential wetland extent by utilizing streamflow statistics and flood-inundation mapping techniques: Pilot study for land along the Wabash River near Terre Haute, Indiana

USGS Publications Warehouse

Kim, Moon H.; Ritz, Christian T.; Arvin, Donald V.

2012-01-01

Potential wetland extents were estimated for a 14-mile reach of the Wabash River near Terre Haute, Indiana. This pilot study was completed by the U.S. Geological Survey in cooperation with the U.S. Department of Agriculture, Natural Resources Conservation Service (NRCS). The study showed that potential wetland extents can be estimated by analyzing streamflow statistics with the available streamgage data, calculating the approximate water-surface elevation along the river, and generating maps by use of flood-inundation mapping techniques. Planning successful restorations for Wetland Reserve Program (WRP) easements requires a determination of areas that show evidence of being in a zone prone to sustained or frequent flooding. Zone determinations of this type are used by WRP planners to define the actively inundated area and make decisions on restoration-practice installation. According to WRP planning guidelines, a site needs to show evidence of being in an "inundation zone" that is prone to sustained or frequent flooding for a period of 7 consecutive days at least once every 2 years on average in order to meet the planning criteria for determining a wetland for a restoration in agricultural land. By calculating the annual highest 7-consecutive-day mean discharge with a 2-year recurrence interval (7MQ2) at a streamgage on the basis of available streamflow data, one can determine the water-surface elevation corresponding to the calculated flow that defines the estimated inundation zone along the river. By using the estimated water-surface elevation ("inundation elevation") along the river, an approximate extent of potential wetland for a restoration in agricultural land can be mapped. As part of the pilot study, a set of maps representing the estimated potential wetland extents was generated in a geographic information system (GIS) application by combining (1) a digital water-surface plane representing the surface of inundation elevation that sloped in the downstream direction of flow and (2) land-surface elevation data. These map products from the pilot study will aid the NRCS and its partners with the onsite inundation-zone verification in agricultural land for a potential restoration and will assist in determining at what elevation to plant hardwood trees for increased survivability on ground above frequently flooded terraces.

The Cumberland River Flood of 2010 and Corps Reservoir Operations

NASA Astrophysics Data System (ADS)

Charley, W.; Hanbali, F.; Rohrbach, B.

2010-12-01

On Saturday, May 1, 2010, heavy rain began falling in the Cumberland River Valley and continued through the following day. 13.5 inches was measured at Nashville, an unprecedented amount that doubled the previous 2-day record, and exceeded the May monthly total record of 11 inches. Elsewhere in the valley, amounts of over 19 inches were measured. The frequency of this storm was estimated to exceed the one-thousand year event. This historic rainfall brought large scale flooding to the Cumberland-Ohio-Tennessee River Valleys, and caused over 2 billion dollars in damages, despite the numerous flood control projects in the area, including eight U.S. Army Corps of Engineers projects. The vast majority of rainfall occurred in drainage areas that are uncontrolled by Corps flood control projects, which lead to the wide area flooding. However, preliminary analysis indicates that operations of the Corps projects reduced the Cumberland River flood crest in Nashville by approximately five feet. With funding from the American Recovery and Reinvestment Act (ARRA) of 2009, hydrologic, hydraulic and reservoir simulation models have just been completed for the Cumberland-Ohio-Tennessee River Valleys. These models are being implemented in the Corps Water Management System (CWMS), a comprehensive data acquisition and hydrologic modeling system for short-term decision support of water control operations in real time. The CWMS modeling component uses observed rainfall and forecasted rainfall to compute forecasts of river flows into and downstream of reservoirs, using HEC-HMS. Simulation of reservoir operations, utilizing either the HEC-ResSim or CADSWES RiverWare program, uses these flow scenarios to provide operational decision information for the engineer. The river hydraulics program, HEC-RAS, computes river stages and water surface profiles for these scenarios. An inundation boundary and depth map of water in the flood plain can be calculated from the HEC-RAS results using ArcInfo. The economic impacts of the different inundation depths are computed by HEC-FIA. The user-configurable sequence of modeling software allows engineers to evaluate operational decisions for reservoirs and other control structures, and view and compare hydraulic and economic impacts for various “what if?” scenarios. This paper reviews the Cumberland River May 2010 event, the impact of Corps reservoirs and reservoir operations and the expected future benefits and effects of the ARRA funded models and CWMS on future events for this area.

Tracking four-decade inundation changes with multi-temporal satellite images in China's largest freshwater lake

NASA Astrophysics Data System (ADS)

Wu, Guiping

2017-04-01

Poyang Lake is the largest freshwater lake in China. The lake has undergone remarkable spatio-temporal changes in both short- and long-term scales since 1970s, resulting in significant hydrological, ecological and economic consequences. Remote sensing techniques have advantages for large-scale studies, by offering images at different spatial and spectral resolutions. However, due to technical difficulties, no single satellite sensor can meet the needs for high spatio-temporal resolution required for such monitoring. In this study, using Landsat Thematic Mapper (TM) and Moderate Resolution Imaging Spectroradiometer (MODIS) images collected between 1973 and 2012, we documented and investigated the short- and long-term characteristics of lake inundation based on Normalized Difference Water Index (NDWI). First, we presented a novel downscaling method based on the NDWI statistical regression algorithm to generate small-scale resolution inundation map (30m) from coarse MODIS data (500m). The downscaling is a linear calibration of the NDWI index from MODIS imagery to Landsat imagery, which is based on the assumption that the relationships between fine resolution and coarse resolution are invariable. Second, Tupu analysis method was further performed to explore the spatial-temporal distribution and changing processes of lake inundation based on downscaling inundation maps. Then, a defined water variation rate (WVR) and inundation frequency (IF) indicator was used to reveal seasonal water surface submersion/exposure processes of lake expansion and shrinkage in different zones. Finally, mathematical statistics methods were utilized to explore the possible driving mechanisms of the revealed change patterns with meteorological data and hydrological data. The results show that, there is a high correlation (mean absolute error of 3.95% and an R2 of 0.97) between the MODIS- and Landsat-derived water surface areas in Poyang Lake. Over the past 40 years, a declining trend to a certain extent for the Poyang Lake's area could be detected. The lake surface displayed comparatively low values ( 2000 km2) in wet periods of 1980, 2006, 2009 and 2011, corresponding to severe hydrological droughts in the lake. In addition, the water surface variation in Poyang Lake had a typical seasonal behavior. It mostly followed a unimodal cycle with area peaks appeared in the wet season. The earliest beginning of the inundation cycle was emerged in 2000 and the latest in 2006. In general, the change of lake area is a synthetic result of climate change, land-cover change and construction of dykes. Our findings should be valuable to a comprehensive understanding of Poyang Lake's decadal and seasonal variation, which is critical for flood/drought prevention, land use planning and lake ecological conservation.

Spatial-Temporal dynamics of surface water flooding and consequences for emergency services accessibility

NASA Astrophysics Data System (ADS)

Pattison, Ian; Green, Daniel; Yu, Dapeng; Bosher, Lee; Wilby, Rob; Yang, Lili; Ryley, Tim

2016-04-01

Urban areas are increasingly susceptible to surface water flooding, with more intense precipitation and intensification of land development. Flooding has both direct impacts i.e. locations inundated with water, and indirect impacts i.e. transport networks, utility e.g. electricity/water services etc. The direct areas flooded evolve in space through the event, and are predicted by standard inundation models. However, the wider indirect impacts and the spatial-temporal patterns are less constrained and it is these that are needed to manage the impacts in real-time. This paper focusses on the Category One responders of the Fire and Rescue and Ambulance Services in the City of Leicester, East Midlands, UK. Leicester is ranked 16th out of 4215 settlements at risk of surface water flooding in the UK based upon the population at risk (15,200 people) (DEFRA, 2009). The analysis undertaken involved overlaying the flood extent with the Integrated Transport Network (ITN) data within a GIS framework. Then a simple transport routing algorithm was used to predict the travel time from specific nodes representing ambulance or fire stations to different parts of the city. Flood magnitudes with 1:20, 1:100 and 1:1000 return periods have been investigated. Under a scenario of no flooding, 100% of the city is accessible by the six fire stations in the city. However, in the 1 in 20 year surface water flood event the peak inundation results in 66.5% being accessible in the 10 minute permitted time and 6% is totally inaccessible. This falls to 40% and 13% respectively for the 1 in 100 year event. Maps show the area of the city that are accessible by two or more stations within the permitted response time, which shows these areas are the most resilient to surface water flooding. However, it isn't just the peak water depths at every location which impacts accessibility within the city but the spatial-temporal patterns of the inundation. The areas within the 10 minute response time expand and contract through the event as the inundated area makes roads in different parts of the city inaccessible through the event. These maps also allow key access roads to be identified. Key stakeholders, within the City of Leicester, have highlighted the potential benefit of such dynamic accessibility maps for their multi-agency planning and response for surface water flooding.

Floods on White Rock Creek above White Rock Lake at Dallas, Texas

USGS Publications Warehouse

Gilbert, Clarence R.

1963-01-01

The White Rock Creek watershed within the city limits of Dallas , Texas, presents problems not unique in the rapid residential and industrial development encountered by many cities throughout the United States. The advantages of full development of the existing area within a city before expanding city boundaries, are related to both economics and civic pride. The expansion of city boundaries usually results in higher per capital costs for the operation of city governments. Certainly no responsible city official would oppose reasonable development of watersheds and flood plains and thus sacrifice an increase in tax revenue. Within the words "reasonable development" lies the problem faced by these officials. They are aware that the natural function of a stream channel, and its associated flood plain is to carry away excess water in time of flood. They are also aware that failure to recognize this has often led to haphazard development on flood plains with a consequent increase in flood damages. In the absence of factual data defining the risk involved in occupying flood plains, stringent corrective and preventative measures must be taken to regulate man's activities on flood plains to a point beyond normal precaution. Flood-flow characteristics in the reach of White Rock Creek that lies between the northern city boundary of Dallas and Northwest Highway (Loop 12) at the upper end of White Rock Lake, are presented in this report. Hydrologic data shown include history and magnitude of floods, flood profiles, outlines of areas inundated by three floods, and estimates of mean velocities of flow at selected points. Approximate areas inundated by floods of April 1942 and July 1962 along White Rock Creek and by the flood of October 1962 along Cottonwood Creek, Floyd Branch, and Jackson Branch, are delineated on maps. Greater floods have undoubtedly occurred in the past but no attempt is made to show their probable overflow limits because basic data on such floods could not be obtained. Depths of inundation can be estimated from the information shown. Elevations shown are in feet above mean sea level, datum of 1929. The data and computations supporting the results given herein are in the files of the Geological Survey in Austin, Texas.

Study of flood defense structural measures priorities using Compromise Programming technique

NASA Astrophysics Data System (ADS)

Lim, D.; Jeong, S.

2017-12-01

Recent climate change of global warming has led to the frequent occurrence of heavy regional rainfalls. As such, inundation vulnerability increases in urban areas with high population density due to the low runoff carrying capacity. This study selects a sample area (Janghang-eup, the Republic of Korea), which is one of the most vulnerable areas to flooding, analyzing the urban flood runoff model (XP-SWMM) and using the MCDM (Multi-Criteria Decision Making) technique to establish flood protection structural measures. To this end, we compare the alternatives and choose the optimal flood defense measure: our model is utilized with three flood prevention structural measures; (i) drainage pipe construction; (ii) water detention; and (iii) flood pumping station. Dividing the target area into three small basins, we propose flood evaluations for an inundation decrease by studying the flooded area, the maximum inundation depth, the damaged residential area, and the construction cost. In addition, Compromise Programming determines the priority of the alternatives. As a consequent, this study suggests flood pumping station for Zone 1 and drainage pipe construction for Zone 2 and Zone 3, respectively, as the optimal flood defense alternative. Keywords : MCDM; Compromise Programming; Urban Flood Prevention; This research was supported by a grant [MPSS-DP-2013-62] through the Disaster and Safety Management Institute funded by Ministry of Public Safety and Security of Korean government.

Validation and Performance Comparison of Numerical Codes for Tsunami Inundation

NASA Astrophysics Data System (ADS)

Velioglu, D.; Kian, R.; Yalciner, A. C.; Zaytsev, A.

2015-12-01

In inundation zones, tsunami motion turns from wave motion to flow of water. Modelling of this phenomenon is a complex problem since there are many parameters affecting the tsunami flow. In this respect, the performance of numerical codes that analyze tsunami inundation patterns becomes important. The computation of water surface elevation is not sufficient for proper analysis of tsunami behaviour in shallow water zones and on land and hence for the development of mitigation strategies. Velocity and velocity patterns are also crucial parameters and have to be computed at the highest accuracy. There are numerous numerical codes to be used for simulating tsunami inundation. In this study, FLOW 3D and NAMI DANCE codes are selected for validation and performance comparison. Flow 3D simulates linear and nonlinear propagating surface waves as well as long waves by solving three-dimensional Navier-Stokes (3D-NS) equations. FLOW 3D is used specificaly for flood problems. NAMI DANCE uses finite difference computational method to solve linear and nonlinear forms of shallow water equations (NSWE) in long wave problems, specifically tsunamis. In this study, these codes are validated and their performances are compared using two benchmark problems which are discussed in 2015 National Tsunami Hazard Mitigation Program (NTHMP) Annual meeting in Portland, USA. One of the problems is an experiment of a single long-period wave propagating up a piecewise linear slope and onto a small-scale model of the town of Seaside, Oregon. Other benchmark problem is an experiment of a single solitary wave propagating up a triangular shaped shelf with an island feature located at the offshore point of the shelf. The computed water surface elevation and velocity data are compared with the measured data. The comparisons showed that both codes are in fairly good agreement with each other and benchmark data. All results are presented with discussions and comparisons. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement No 603839 (Project ASTARTE - Assessment, Strategy and Risk Reduction for Tsunamis in Europe)

Verification of Reproduction Simulation of the 2011 Great East Japan Tsunami Using Time-Stamp Data

NASA Astrophysics Data System (ADS)

Honma, Motohiro; Ushiyama, Motoyuki

2014-05-01

In the 2011 off the pacific coast of Tohoku earthquake tsunami, the significant damage and loss of lives were caused by large tsunami in the pacific coastal areas of the northern Japan. It is important to understand the situation of tsunami inundation in detail in order to establish the effective measures of disaster prevention. In this study, we calculated the detailed tsunami inundation simulation of Rikuzentakata city and verified the simulation results using not only the static observed data such as inundation area and tsunami height estimated by traces but also time stamp data which were recorded to digital camera etc. We calculated the tsunami simulation by non-linear long-wave theory using the staggered grid and leap flog scheme. We used Fujii and Satake (2011)'s model ver.4.2 as the tsunami source. The inundation model of Rikuzentakata city was constructed by fine ground level data of 10m mesh. In this simulation, the shore and river banks were set in boundary of calculation mesh. At that time, we have calculated two patterns of simulation, one condition is that a bank doesn't collapse even if tsunami overflows on it, another condition is that a bank collapses if tsunami overflows on it and its discharge exceeds the threshold. We can use the inundation area data, which was obtained by Geospatial Information Authority of Japan (GSI), and height data of tsunami trace, which were obtained by the 2011 Tohoku Earthquake Joint Survey (TTJS) group, as "static" verification data. Comparing the inundation area of simulation result with its observation by GSI, both areas are matched very well. And then, correlation coefficient between tsunami height data resulted from simulation and observed by TTJS is 0.756. In order to verify tsunami arrival time, we used the time stamp data which were recorded to digital camera etc. by citizens. Ushiyama and Yokomaku (2012) collected these tsunami stamp data and estimated the arrival time in Rikuzentakata city. We compared the arrival time resulted from tsunami simulation with estimated by Ushiyama and Yokomaku (2012) for some major points. The arrival time is earlier 2-4 minutes in the condition that a bank collapses when tsunami overflows and its discharge exceeds 0.05m2/s at each mesh boundary than in the condition that a bank doesn't collapse. And, on the whole the arrival time estimated from time stamp data is in accord with the result which were calculated in the condition that a bank collapse. We could verify reproducibility about not only the final tsunami inundation situation but also the temporal change of tsunami inundation situation by using the time stamp data. Acknowledgement In this study, we used tsunami trace data obtained by The 2011 Tohoku Earthquake Tsunami Joint Survey (TTJS) Group. Reference 1) Fujii and Satake: Tsunami Source of the Off Tohoku-Pacific Earthquake on March 11, 2011, http://iisee.kenken.go.jp/staff/fujii/OffTohokuPacific2011/tsunami_ja_ver4.2and4.6.html, 2011. 2) Ushiyama and Yokomaku: Estimation of situation in Rikuzentakata city just before tsunami attack based on time stamp data, J.JSNDS31-1, pp.47-58, 2012.

Comparing National Water Model Inundation Predictions with Hydrodynamic Modeling

NASA Astrophysics Data System (ADS)

Egbert, R. J.; Shastry, A.; Aristizabal, F.; Luo, C.

2017-12-01

The National Water Model (NWM) simulates the hydrologic cycle and produces streamflow forecasts, runoff, and other variables for 2.7 million reaches along the National Hydrography Dataset for the continental United States. NWM applies Muskingum-Cunge channel routing which is based on the continuity equation. However, the momentum equation also needs to be considered to obtain better estimates of streamflow and stage in rivers especially for applications such as flood inundation mapping. Simulation Program for River NeTworks (SPRNT) is a fully dynamic model for large scale river networks that solves the full nonlinear Saint-Venant equations for 1D flow and stage height in river channel networks with non-uniform bathymetry. For the current work, the steady-state version of the SPRNT model was leveraged. An evaluation on SPRNT's and NWM's abilities to predict inundation was conducted for the record flood of Hurricane Matthew in October 2016 along the Neuse River in North Carolina. This event was known to have been influenced by backwater effects from the Hurricane's storm surge. Retrospective NWM discharge predictions were converted to stage using synthetic rating curves. The stages from both models were utilized to produce flood inundation maps using the Height Above Nearest Drainage (HAND) method which uses the local relative heights to provide a spatial representation of inundation depths. In order to validate the inundation produced by the models, Sentinel-1A synthetic aperture radar data in the VV and VH polarizations along with auxiliary data was used to produce a reference inundation map. A preliminary, binary comparison of the inundation maps to the reference, limited to the five HUC-12 areas of Goldsboro, NC, yielded that the flood inundation accuracies for NWM and SPRNT were 74.68% and 78.37%, respectively. The differences for all the relevant test statistics including accuracy, true positive rate, true negative rate, and positive predictive value were found to be statistically significant. Further research will include a larger segment of the Neuse River to make more confident conclusions on how SPRNT can improve on NWM predictions. An interactive Tethys web application was developed to display and compare the inundation maps.

Social media as an information source for rapid flood inundation mapping

NASA Astrophysics Data System (ADS)

Fohringer, J.; Dransch, D.; Kreibich, H.; Schröter, K.

2015-12-01

During and shortly after a disaster, data about the hazard and its consequences are scarce and not readily available. Information provided by eyewitnesses via social media is a valuable information source, which should be explored in a~more effective way. This research proposes a methodology that leverages social media content to support rapid inundation mapping, including inundation extent and water depth in the case of floods. The novelty of this approach is the utilization of quantitative data that are derived from photos from eyewitnesses extracted from social media posts and their integration with established data. Due to the rapid availability of these posts compared to traditional data sources such as remote sensing data, areas affected by a flood, for example, can be determined quickly. The challenge is to filter the large number of posts to a manageable amount of potentially useful inundation-related information, as well as to interpret and integrate the posts into mapping procedures in a timely manner. To support rapid inundation mapping we propose a methodology and develop "PostDistiller", a tool to filter geolocated posts from social media services which include links to photos. This spatial distributed contextualized in situ information is further explored manually. In an application case study during the June 2013 flood in central Europe we evaluate the utilization of this approach to infer spatial flood patterns and inundation depths in the city of Dresden.

Social media as an information source for rapid flood inundation mapping

NASA Astrophysics Data System (ADS)

Fohringer, J.; Dransch, D.; Kreibich, H.; Schröter, K.

2015-07-01

During and shortly after a disaster data about the hazard and its consequences are scarce and not readily available. Information provided by eye-witnesses via social media are a valuable information source, which should be explored in a more effective way. This research proposes a methodology that leverages social media content to support rapid inundation mapping, including inundation extent and water depth in case of floods. The novelty of this approach is the utilization of quantitative data that are derived from photos from eye-witnesses extracted from social media posts and its integration with established data. Due to the rapid availability of these posts compared to traditional data sources such as remote sensing data, for example areas affected by a flood can be determined quickly. The challenge is to filter the large number of posts to a manageable amount of potentially useful inundation-related information as well as their timely interpretation and integration in mapping procedures. To support rapid inundation mapping we propose a methodology and develop a tool to filter geo-located posts from social media services which include links to photos. This spatial distributed contextualized in-situ information is further explored manually. In an application case study during the June 2013 flood in central Europe we evaluate the utilization of this approach to infer spatial flood patterns and inundation depths in the city of Dresden.

Inundation and salinity impacts to above- and belowground productivity in Spartina patens and Spartina alterniflora in the Mississippi River Deltaic Plain: implications for using river diversions as restoration tools

USGS Publications Warehouse

Snedden, Gregg A.; Cretini, Kari Foster; Patton, Brett

2015-01-01

Inundation and salinity directly affect plant productivity and processes that regulate vertical accretion in coastal wetlands, and are expected to increase as sea level continues to rise. In the Mississippi River deltaic plain, river diversions, which are being implemented as ecosystem restoration tools, can also strongly increase inundation in coastal wetlands. We used an in situ mesocosm approach to examine how varying salinity (two levels) and inundation rates (six levels) influenced end-of-season above- and belowground biomass of Spartina patens and Spartina alterniflora during the growing season (March–October) in 2011. Above- and belowground biomass was highest in both species at higher elevations when inundation was minimal, and decreased exponentially with decreased elevation and increased flood duration. This negative biomass response to flooding was more pronounced in S. patens than in S. alterniflora, and S. patens also showed stronger biomass reductions at higher salinities. This salinity effect was absent for belowground biomass in S. alterniflora. These findings suggest that even subtle increases in sea level may lead to substantial reductions in productivity and organic accretion, and also illustrate the importance of considering the inundation tolerance of co-dominant species in receiving areas when utilizing river diversions for delta restoration.

Flood-inundation maps for the Wabash River at Memorial Bridge at Vincennes, Indiana

USGS Publications Warehouse

Fowler, Kathleen K.; Menke, Chad D.

2017-08-23

Digital flood-inundation maps for a 10.2-mile reach of the Wabash River from Sevenmile Island to 3.7 mile downstream of Memorial Bridge (officially known as Lincoln Memorial Bridge) at Vincennes, Indiana, were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03343010, Wabash River at Memorial Bridge at Vincennes, Ind. Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site.For this study, flood profiles were computed for the Wabash River reach by means of a one-dimensional stepbackwater model. The hydraulic model was calibrated by using the most current stage-discharge relations at USGS streamgage 03343010, Wabash River at Memorial Bridge at Vincennes, Ind., and preliminary high-water marks from a high-water event on April 27, 2013. The calibrated hydraulic model was then used to determine 19 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 10 feet (ft) or near bankfull to 28 ft, the highest stage of the current stage-discharge rating curve. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) digital elevation model (DEM, derived from Light Detection and Ranging [lidar] data having a 0.98-ft vertical accuracy and 4.9-ft horizontal resolution) in order to delineate the area flooded at each water level.The availability of these maps—along with Internet information regarding current stage from the USGS streamgage 03343010, and forecast stream stages from the NWS AHPS—provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

EXPERIMENTAL STUDIES ON DIFFICULTY OF EVACUATION FROM UNDERGROUND SPACES UNDER INUNDATED SITUATIONS USING REAL SCALE MODELS

NASA Astrophysics Data System (ADS)

Baba, Yasuyuki; Ishigaki, Taisuke; Toda, Keiichi; Nakagawa, Hajime

Many urbanized cities in Japan are located in alluvial plains, and the vulnerability of urbanized areas to flood disaster is highlighted by flood attacks due to heavy rain fall or typhoons. Underground spaces located in the urbanized area are flood-prone areas, and the intrusion of flood watar into underground space inflicted severe damages on urban functions and infrastructures. In a similar way, low-lying areas like "bowl-shaped" depression and underpasses under highway and railroad bridges are also prone to floods. The underpasses are common sites of accidents of submerged vehicles, and severe damage including human damage occasionally occurs under flooding conditions. To reduce the damage due to inundation in underground space, needless to say, early evacuation is one of the most important countermeasures. This paper shows some experimental results of evacuation tests from underground spaces under inundated situations. The difficulities of the evacuation from underground space has been investigated by using real scale models (door, staircase and vehicle), and the limit for safety evacuation is discussed. From the results, it is found that water depth of 0.3 - 0.4m would be a critical situation for the evacuation from underground space through staircases and door and that 0.7 - 0.8m deep on the ground would be also a critical situation for safety evacuation though the doors of the vehicle. These criteria have some possibility to vary according to different inundated situations, and they are also influenced by the individual variation like the difference of physical strength. This means that these criteria requires cautious stance to use although they show a sort of an index of the limitation for saftty evacuation from underground space.

Impact of Flooding on Land Use/ Land Cover Transformation in Wular Lake and its Environs, Kashmir Valley, India Using Geoinformatics

NASA Astrophysics Data System (ADS)

Ahmad, T.; Pandey, A. C.; Kumar, A.

2017-11-01

Wular lake, located at an elevation of 1520 m above sea level in Kashmir valley, India. In the present study, the immediate and long term impact of flood (2014) over the Wular lake environs was analyzed by using satellite images and employing supervised classification technique in GIS environment. The LULC classification was performed on the images of 25th August 2014 (pre flood) and 13th September 2015 (post flood) and was compared, which indicated marked decrease in terrestrial vegetation (23.7 %), agriculture (43.7 %) and water bodies (39.9 %). Overlaying analysis was performed with pre and post flood classified images with reference to the satellite image of 10th September 2014(during flood) which indicated total area inundated during flood was 88.77 km2. With the pre-flood situation, the aquatic vegetation of 34.06 km2, 13.89 km2 of agriculture land and terrestrial vegetation of 3.13 km2 was inundated. In the post flood situation, it was also came into focus that more than the half of the area under water bodies was converted into sand deposits (22.76 km2) due to anomalous increase in siltation. The overlay analysis on post flood classified image indicated that aquatic vegetation followed by agriculture and sand deposits lie within the flood inundated area. Further spatial analysis was performed within the flood inundated area (88.77 km2) with pre and post classified image to understand the situation before and after the flood and to calculate the changes. These land use-land cover transformations signifies the ill effect of flooding on the biodiversity of Wular Lake.

Assessing downstream flood impacts due to a potential GLOF from Imja Lake in Nepal

NASA Astrophysics Data System (ADS)

Somos-Valenzuela, M. A.; McKinney, D. C.; Byers, A. C.; Rounce, D. R.; Portocarrero, C.; Lamsal, D.

2014-11-01

Glacial-dominated areas pose unique challenges to downstream communities in adapting to recent and continuing global climate change, including increased threats of glacial lake outburst floods (GLOFs) that can increase risk due to flooding of downstream communities and cause substantial impacts on regional social, environmental and economic systems. The Imja glacial lake in Nepal, with potential to generate a GLOF, was studied using a two-dimensional debris flow inundation model in order to evaluate the effectiveness of proposed measures to reduce possible flooding impacts to downstream communities by lowering the lake level. The results indicate that only minor flood impact reduction is achieved in the downstream community of Dingboche with modest (~3 m) lake lowering. Lowering the lake by 10 m shows a significant reduction in inundated area. However, lowering the lake by 20 m almost eliminates all flood impact at Dingboche. Further downstream at Phakding, the impact of the GLOF is significant and similar reductions in inundation are likely as a result of lake lowering.

The HEC RAS model of regulated stream for purposes of flood risk reduction

NASA Astrophysics Data System (ADS)

Fijko, Rastislav; Zeleňáková, Martina

2016-06-01

The work highlights the modeling of water flow in open channels using 1D mathematical model HEC-RAS in the area of interest Lopuchov village in eastern Slovakia. We created a digital model from a geodetic survey, which was used to show the area of inundation in ArcGIS software. We point out the modeling methodology with emphasis to collection of the data and their relevance for determination of boundary conditions in 3D model of the study area in GIS platform. The BIM objects can be exported to the defined model of the area. The obtained results were used for simulation of flooding. The results give to us clearly and distinctly defined areas of inundation, which we used in the processing of Cost benefit analysis. We used the developed model for stating the potential damages in flood vulnerable areas.

The use of the LANDSAT data collection system and imagery in reservoir management and operation. [Maine, Vermont, New Hamphire, Canada, St. John River, Beech Ridge, Merrimack River, and Franklin Falls

NASA Technical Reports Server (NTRS)

Cooper, S. (Principal Investigator); Buckelew, T. D.; Mckim, H. L.; Merry, C. J.

1977-01-01

The author has identified the following significant results. An increase in the data collection system's (DCS) ability to function in the flood control mission with no additional manpower was demonstrated during the storms which struck New England during April and May of 1975 and August 1976. It was found that for this watershed, creditable flood hydrographs could be generated from DCS data. It was concluded that an ideal DCS for reservoir regulation would draw features from LANDSAT and GOES. MSS grayscale computer printout and a USGS topographic map were compared, yielding an optimum computer classification map of the wetland areas of the Merrimack River estuary. A classification accuracy of 75% was obtained for the wetlands unit, taking into account the misclassified and the unclassified pixels. The MSS band 7 grayscale printouts of the Franklin Falls reservoir showed good agreement to USGS topographic maps in total area of water depicted at the low water reservoir stage and at the maximum inundation level. Preliminary analysis of the LANDSAT digital data using the GISS computer algorithms showed that the radiance of snow cover/vegetation varied from approximately 20 mW/sq cm sr in nonvegetated areas to less than 4 mW/sq cm sr for densely covered forested area.

Numerical tool for tsunami risk assessment in the southern coast of Dominican Republic

NASA Astrophysics Data System (ADS)

Macias Sanchez, J.; Llorente Isidro, M.; Ortega, S.; Gonzalez Vida, J. M., Sr.; Castro, M. J.

2016-12-01

The southern coast of Dominican Republic is a very populated region, with several important cities including Santo Domingo, its capital. Important activities are rooted in the southern coast including tourism, industry, commercial ports, and, energy facilities, among others. According to historical reports, it has been impacted by big earthquakes accompanied by tsunamis as in Azua in 1751 and recently Pedernales in 2010, but their sources are not clearly identified. The aim of the present work is to develop a numerical tool to simulate the impact in the southern coast of the Dominican Republic of tsunamis generated in the Caribbean Sea. This tool, based on the Tsunami-HySEA model from EDANYA group (University of Malaga, Spain), could be used in the framework of a Tsunami Early Warning Systems due the very short computing times when only propagation is computed or it could be used to assess inundation impact, computing inundation with a initial 5 meter resolution. Numerical results corresponding to three theoretical sources are used to test the numerical tool.

Computational technique and performance of Transient Inundation Model for Rivers--2 Dimensional (TRIM2RD) : a depth-averaged two-dimensional flow model

USGS Publications Warehouse

Fulford, Janice M.

2003-01-01

A numerical computer model, Transient Inundation Model for Rivers -- 2 Dimensional (TrimR2D), that solves the two-dimensional depth-averaged flow equations is documented and discussed. The model uses a semi-implicit, semi-Lagrangian finite-difference method. It is a variant of the Trim model and has been used successfully in estuarine environments such as San Francisco Bay. The abilities of the model are documented for three scenarios: uniform depth flows, laboratory dam-break flows, and large-scale riverine flows. The model can start computations from a ?dry? bed and converge to accurate solutions. Inflows are expressed as source terms, which limits the use of the model to sufficiently long reaches where the flow reaches equilibrium with the channel. The data sets used by the investigation demonstrate that the model accurately propagates flood waves through long river reaches and simulates dam breaks with abrupt water-surface changes.

Hydrologic indicators of hot spots and hot moments of mercury methylation potential along river corridors

USGS Publications Warehouse

Singer, Michael B.; Harrison, Lee R.; Donovan, Patrick M.; Blum, Joel D.; Marvin-DiPasquale, Mark C.

2016-01-01

The biogeochemical cycling of metals and other contaminants in river-floodplain corridors is controlled by microbial activity responding to dynamic redox conditions. Riverine flooding thus has the potential to affect speciation of redox-sensitive metals such as mercury (Hg). Therefore, inundation history over a period of decades potentially holds information on past production of bioavailable Hg. We investigate this within a Northern California river system with a legacy of landscape-scale 19th century hydraulic gold mining. We combine hydraulic modeling, Hg measurements in sediment and biota, and first-order calculations of mercury transformation to assess the potential role of river floodplains in producing monomethylmercury (MMHg), a neurotoxin which accumulates in local and migratory food webs. We identify frequently inundated floodplain areas, as well as floodplain areas inundated for long periods. We quantify the probability of MMHg production potential (MPP) associated with hydrology in each sector of the river system as a function of the spatial patterns of overbank inundation and drainage, which affect long-term redox history of contaminated sediments. Our findings identify river floodplains as periodic, temporary, yet potentially important, loci of biogeochemical transformation in which contaminants may undergo change during limited periods of the hydrologic record. We suggest that inundation is an important driver of MPP in river corridors and that the entire flow history must be analyzed retrospectively in terms of inundation magnitude and frequency in order to accurately assess biogeochemical risks, rather than merely highlighting the largest floods or low-flow periods. MMHg bioaccumulation within the aquatic food web in this system may pose a major risk to humans and waterfowl that eat migratory salmonids, which are being encouraged to come up these rivers to spawn. There is a long-term pattern of MPP under the current flow regime that is likely to be accentuated by increasingly common large floods with extended duration.

Hydrologic indicators of hot spots and hot moments of mercury methylation potential along river corridors.

PubMed

Singer, Michael Bliss; Harrison, Lee R; Donovan, Patrick M; Blum, Joel D; Marvin-DiPasquale, Mark

2016-10-15

The biogeochemical cycling of metals and other contaminants in river-floodplain corridors is controlled by microbial activity responding to dynamic redox conditions. Riverine flooding thus has the potential to affect speciation of redox-sensitive metals such as mercury (Hg). Therefore, inundation history over a period of decades potentially holds information on past production of bioavailable Hg. We investigate this within a Northern California river system with a legacy of landscape-scale 19th century hydraulic gold mining. We combine hydraulic modeling, Hg measurements in sediment and biota, and first-order calculations of mercury transformation to assess the potential role of river floodplains in producing monomethylmercury (MMHg), a neurotoxin which accumulates in local and migratory food webs. We identify frequently inundated floodplain areas, as well as floodplain areas inundated for long periods. We quantify the probability of MMHg production potential (MPP) associated with hydrology in each sector of the river system as a function of the spatial patterns of overbank inundation and drainage, which affect long-term redox history of contaminated sediments. Our findings identify river floodplains as periodic, temporary, yet potentially important, loci of biogeochemical transformation in which contaminants may undergo change during limited periods of the hydrologic record. We suggest that inundation is an important driver of MPP in river corridors and that the entire flow history must be analyzed retrospectively in terms of inundation magnitude and frequency in order to accurately assess biogeochemical risks, rather than merely highlighting the largest floods or low-flow periods. MMHg bioaccumulation within the aquatic food web in this system may pose a major risk to humans and waterfowl that eat migratory salmonids, which are being encouraged to come up these rivers to spawn. There is a long-term pattern of MPP under the current flow regime that is likely to be accentuated by increasingly common large floods with extended duration. Copyright © 2016 Elsevier B.V. All rights reserved.

Development of Inundation Map for Bantayan Island, Cebu Using Delft3D-Flow Storm Surge Simulations of Typhoon Haiyan

NASA Astrophysics Data System (ADS)

Cuadra, Camille; Suarez, John Kenneth; Biton, Nophi Ian; Cabacaba, Krichi May; Lapidez, John Phillip; Santiago, Joy; Mahar Francisco Lagmay, Alfredo; Malano, Vicente

2014-05-01

On average, 20 typhoons enter the Philippine area of responsibility annually, making it vulnerable to different storm hazards. Apart from the frequency of tropical cyclones, the archipelagic nature of the country makes it particularly prone to storm surges. On 08 November 2013, Haiyan, a Category 5 Typhoon with maximum one-minute sustained wind speed of 315 kph, hit the central region of the Philippines. In its path, the howler devastated Bantayan Island, a popular tourist destination. The island is located north of Cebu City, the second largest metropolis of the Philippines in terms of populace. Having been directly hit by Typhoon Haiyan, Bantayan Island was severely damaged by strong winds and storm surges, with more than 11,000 houses totally destroyed while 5,000 more suffered minor damage. The adverse impacts of possible future storm surge events in the island can only be mitigated if hazard maps that depict inundation of the coastal areas of Bantayan are generated. To create such maps, Delft3D-Flow, a hydrodynamic model was used to simulate storm surges. These simulations were made over a 10-m per pixel resolution Digital Elevation Model (DEM) and the General Bathymetric Chart of the Oceans (GEBCO) bathymetry. The results of the coastal inundation model for Typhoon Haiyan's storm surges were validated using data collected from field work and local government reports. The hydrodynamic model of Bantayan was then calibrated using the field data and further simulations were made with varying typhoon tracks. This was done to generate scenarios on the farthest possible inland incursion of storm surges. The output of the study is a detailed storm surge inundation map that depicts safe zones for development of infrastructure near coastal areas and for construction of coastal protection structures. The storm surge inundation map can also be used as basis for disaster preparedness plans of coastal communities threatened by approaching typhoons.

44 CFR 64.3 - Flood Insurance Maps.

Code of Federal Regulations, 2012 CFR

2012-10-01

... tidal floods (coastal high hazard area) V1-30, VE Area of special flood hazards, with water surface elevations determined and with velocity, that is inundated by tidal floods (coastal high hazard area) V0 Area..., but possible, mudslide hazards E Area of special flood-related erosion hazards. Areas identified as...

44 CFR 64.3 - Flood Insurance Maps.

Code of Federal Regulations, 2013 CFR

2013-10-01

... tidal floods (coastal high hazard area) V1-30, VE Area of special flood hazards, with water surface elevations determined and with velocity, that is inundated by tidal floods (coastal high hazard area) V0 Area..., but possible, mudslide hazards E Area of special flood-related erosion hazards. Areas identified as...

44 CFR 64.3 - Flood Insurance Maps.

Code of Federal Regulations, 2014 CFR

2014-10-01

... tidal floods (coastal high hazard area) V1-30, VE Area of special flood hazards, with water surface elevations determined and with velocity, that is inundated by tidal floods (coastal high hazard area) V0 Area..., but possible, mudslide hazards E Area of special flood-related erosion hazards. Areas identified as...

Vulnerability of National Park Service beaches to inundation during a direct hurricane landfall: Fire Island National Seashore

USGS Publications Warehouse

Stockdon, Hilary F.; Thompson, David M.

2007-01-01

Waves and storm surge associated with strong tropical storms are part of the natural process of barrier-island evolution and can cause extensive morphologic changes in coastal parks, leading to reduced visitor accessibility and enjoyment. Even at Fire Island National Seashore, a barrier-island coastal park in New York where extratropical storms (northeasters) dominate storm activity, the beaches are vulnerable to the powerful, sand-moving forces of hurricanes. The vulnerability of park beaches to inundation, and associated extreme coastal change, during a direct hurricane landfall can be assessed by comparing the elevations of storm-induced mean-water levels (storm surge) to the elevations of the crest of the sand dune that defines the beach system. Maps detailing the inundation potential for Category 1-4 hurricanes can be used by park managers to determine the relative vulnerability of various barrier-island parks and to assess which areas of a particular park are more susceptible to inundation and extreme coastal changes.

Modeling a glacial lake outburst flood process chain: the case of Lake Palcacocha and Huaraz, Peru

NASA Astrophysics Data System (ADS)

Somos-Valenzuela, Marcelo A.; Chisolm, Rachel E.; Rivas, Denny S.; Portocarrero, Cesar; McKinney, Daene C.

2016-07-01

One of the consequences of recent glacier recession in the Cordillera Blanca, Peru, is the risk of glacial lake outburst floods (GLOFs) from lakes that have formed at the base of retreating glaciers. GLOFs are often triggered by avalanches falling into glacial lakes, initiating a chain of processes that may culminate in significant inundation and destruction downstream. This paper presents simulations of all of the processes involved in a potential GLOF originating from Lake Palcacocha, the source of a previously catastrophic GLOF on 13 December 1941, killing about 1800 people in the city of Huaraz, Peru. The chain of processes simulated here includes (1) avalanches above the lake; (2) lake dynamics resulting from the avalanche impact, including wave generation, propagation, and run-up across lakes; (3) terminal moraine overtopping and dynamic moraine erosion simulations to determine the possibility of breaching; (4) flood propagation along downstream valleys; and (5) inundation of populated areas. The results of each process feed into simulations of subsequent processes in the chain, finally resulting in estimates of inundation in the city of Huaraz. The results of the inundation simulations were converted into flood intensity and preliminary hazard maps (based on an intensity-likelihood matrix) that may be useful for city planning and regulation. Three avalanche events with volumes ranging from 0.5 to 3 × 106 m3 were simulated, and two scenarios of 15 and 30 m lake lowering were simulated to assess the potential of mitigating the hazard level in Huaraz. For all three avalanche events, three-dimensional hydrodynamic models show large waves generated in the lake from the impact resulting in overtopping of the damming moraine. Despite very high discharge rates (up to 63.4 × 103 m3 s-1), the erosion from the overtopping wave did not result in failure of the damming moraine when simulated with a hydro-morphodynamic model using excessively conservative soil characteristics that provide very little erosion resistance. With the current lake level, all three avalanche events result in inundation in Huaraz due to wave overtopping, and the resulting preliminary hazard map shows a total affected area of 2.01 km2, most of which is in the high hazard category. Lowering the lake has the potential to reduce the affected area by up to 35 %, resulting in a smaller portion of the inundated area in the high hazard category.

A Tank Bromeliad Favors Spider Presence in a Neotropical Inundated Forest.

PubMed

Hénaut, Yann; Corbara, Bruno; Pélozuelo, Laurent; Azémar, Frédéric; Céréghino, Régis; Herault, Bruno; Dejean, Alain

2014-01-01

Tank bromeliads are good models for understanding how climate change may affect biotic associations. We studied the relationships between spiders, the epiphytic tank bromeliad, Aechmea bracteata, and its associated ants in an inundated forest in Quintana Roo, Mexico, during a drought period while, exceptionally, this forest was dry and then during the flooding that followed. We compared spider abundance and diversity between 'Aechmea-areas' and 'control-areas' of the same surface area. We recorded six spider families: the Dipluridae, Ctenidae, Salticidae, Araneidae, Tetragnathidae and Linyphiidae among which the funnel-web tarantula, Ischnothele caudata, the only Dipluridae noted, was the most abundant. During the drought period, the spiders were more numerous in the Aechmea-areas than in the control-areas, but they were not obligatorily associated with the Aechmea. During the subsequent flooding, the spiders were concentrated in the A. bracteata patches, particularly those sheltering an ant colony. Also, a kind of specificity existed between certain spider taxa and ant species, but varied between the drought period and subsequent flooding. We conclude that climatic events modulate the relationship between A. bracteata patches and their associated fauna. Tank bromeliads, previously considered only for their ecological importance in supplying food and water during drought, may also be considered refuges for spiders during flooding. More generally, tank bromeliads have an important role in preserving non-specialized fauna in inundated forests.

Assimilation of flood extent data with 2D flood inundation models for localised intense rainfall events

NASA Astrophysics Data System (ADS)

Neal, J. C.; Wood, M.; Bermúdez, M.; Hostache, R.; Freer, J. E.; Bates, P. D.; Coxon, G.

2017-12-01

Remote sensing of flood inundation extent has long been a potential source of data for constraining and correcting simulations of floodplain inundation. Hydrodynamic models and the computing resources to run them have developed to the extent that simulation of flood inundation in two-dimensional space is now feasible over large river basins in near real-time. However, despite substantial evidence that there is useful information content within inundation extent data, even from low resolution SAR such as that gathered by Envisat ASAR in wide swath mode, making use of the information in a data assimilation system has proved difficult. He we review recent applications of the Ensemble Kalman Filter (EnKF) and Particle Filter for assimilating SAR data, with a focus on the River Severn UK and compare these with complementary research that has looked at the internal error sources and boundary condition errors using detailed terrestrial data that is not available in most locations. Previous applications of the EnKF to this reach have focused on upstream boundary conditions as the source of flow error, however this description of errors was too simplistic for the simulation of summer flood events where localised intense rainfall can be substantial. Therefore, we evaluate the introduction of uncertain lateral inflows to the ensemble. A further limitation of the existing EnKF based methods is the need to convert flood extent to water surface elevations by intersecting the shoreline location with a high quality digital elevation model (e.g. LiDAR). To simplify this data processing step, we evaluate a method to directly assimilate inundation extent as a EnKF model state rather than assimilating water heights, potentially allowing the scheme to be used where high-quality terrain data are sparse.

Towards a High-Resolution Global Inundation Delineation Dataset

NASA Astrophysics Data System (ADS)

Fluet-Chouinard, E.; Lehner, B.

2011-12-01

Although their importance for biodiversity, flow regulation and ecosystem service provision is widely recognized, wetlands and temporarily inundated landscapes remain poorly mapped globally because of their inherent elusive nature. Inventorying of wetland resources has been identified in international agreements as an essential component of appropriate conservation efforts and management initiatives of these threatened ecosystems. However, despite recent advances in remote sensing surface water monitoring, current inventories of surface water variations remain incomplete at the regional-to-global scale due to methodological limitations restricting truly global application. Remote sensing wetland applications such as SAR L-band are particularly constrained by image availability and heterogeneity of acquisition dates, while coarse resolution passive microwave and multi-sensor methods cannot discriminate distinct surface water bodies. As a result, the most popular global wetland dataset remains to this day the Global Lake & Wetland Database (Lehner and Doll, 2004) a spatially inconsistent database assembled from various existing data sources. The approach taken in this project circumvents the limitations of current global wetland monitoring methods by combining globally available topographic and hydrographic data to downscale coarse resolution global inundation data (Prigent et al., 2007) and thus create a superior inundation delineation map product. The developed procedure downscales inundation data from the coarse resolution (~27km) of current passive microwave sensors to the finer spatial resolution (~500m) of the topographic and hydrographic layers of HydroSHEDS' data suite (Lehner et al., 2006), while retaining the high temporal resolution of the multi-sensor inundation dataset. From the downscaling process emerges new information on the specific location of inundation, but also on its frequency and duration. The downscaling algorithm employs a decision tree classifier trained on regional remote sensing wetland maps, to derive inundation probability followed by a seeded region growing segmentation process to redistribute the inundated area at the finer resolution. Assessment of the algorithm's performance is accomplished by evaluating the level of agreement between its outputted downscaled inundation maps and existing regional remote sensing inundation delineation. Upon completion, this project's will offer a dynamic globally seamless inundation map at an unprecedented spatial and temporal scale, which will provide the baseline inventory long requested by the research community, and will open the door to a wide array of possible conservation and hydrological modeling applications which were until now data-restricted. Literature Lehner, B., K. Verdin, and A. Jarvis. 2008. New global hydrography derived from spaceborne elevation data. Eos 89, no. 10. Lehner, B, and P Doll. 2004. Development and validation of a global database of lakes, reservoirs and wetlands. Journal of Hydrology 296, no. 1-4: 1-22. Prigent, C., F. Papa, F. Aires, W. B. Rossow, and E. Matthews. 2007. Global inundation dynamics inferred from multiple satellite observations, 1993-2000. Journal of Geophysical Research 112, no. D12: 1-13.

Urban sprawl and flooding in southern California

USGS Publications Warehouse

Rantz, S.E.

1970-01-01

The floods of January 1969 in south-coastal California provide a timely example of the effect of urban sprawl on flood damage. Despite recordbreaking, or near recordbreaking, stream discharges, damage was minimal in the older developed areas that are protected against inundation and debris damage by carefully planned flood-control facilities, including debris basins and flood-conveyance channels. By contrast, heavy damage occurred in areas of more recent urban sprawl, where the hazards of inundation and debris or landslide damage have not been taken into consideration, and where the improvement and development of drainage or flood-control facilities have not kept pace with expanding urbanization.

Assessment of the spatial extent and height of flooding in Lake Champlain during May 2011, using satellite remote sensing and ground-based information

USGS Publications Warehouse

Bjerklie, David M.; Trombley, Thomas J.; Olson, Scott A.

2014-01-01

Landsat 5 and moderate resolution imaging spectro-radiometer satellite imagery were used to map the area of inundation of Lake Champlain, which forms part of the border between New York and Vermont, during May 2011. During this month, the lake’s water levels were record high values not observed in the previous 150 years. Lake inundation area determined from the satellite imagery is correlated with lake stage measured at three U.S. Geological Survey lake level gages to provide estimates of lake area at different lake levels (stage/area rating) and also compared with the levels of the high-water marks (HWMs) located on the Vermont side of the lake. The rating developed from the imagery shows a somewhat different relation than a similar stage/area rating developed from a medium-resolution digital elevation model (DEM) of the region. According to the rating derived from the imagery, the lake surface area during the peak lake level increased by about 17 percent above the average or “normal” lake level. By using a comparable rating developed from the DEM, the increase above average is estimated to be about 12 percent. The northern part of the lake (north of Burlington) showed the largest amount of flooding. Based on intersecting the inundation maps with the medium-resolution DEM, lake levels were not uniform around the lake. This is also evident from the lake level gage measurements and HWMs. The gage data indicate differences up to 0.5 feet between the northern and southern end of the lake. Additionally, the gage data show day-to-day and intradaily variation of the same range (0.5 foot). The high-water mark observations show differences up to 2 feet around the lake, with the highest level generally along the south- and west-facing shorelines. The data suggest that during most of May 2011, water levels were slightly higher and less variable in the northern part of the lake. These phenomena may be caused by wind effects as well as proximity to major river inputs to the lake. The inundation areas generated from the imagery generally coincide with flood mapping as estimated by the Federal Emergency Management Agency (FEMA) and shown on its digital flood insurance rate maps. Where areas in the flood inundation map derived from the imagery and the FEMA estimated flooded areas differ substantially, this difference may be due to differences between the flood magnitude at the time of the image and the assumed flood condition used for the FEMA modeling and mapping, wind/storage effects not accounted for by the FEMA modeling, and the resolution of the image compared to the DEM used in the FEMA mapping.

Assessment of the effects of multiple extreme floods on flow and transport processes under competing flood protection and environmental management strategies.

PubMed

Tu, Tongbi; Carr, Kara J; Ercan, Ali; Trinh, Toan; Kavvas, M Levent; Nosacka, John

2017-12-31

Extreme floods are regarded as one of the most catastrophic natural hazards and can result in significant morphological changes induced by pronounced sediment erosion and deposition processes over the landscape. However, the effects of extreme floods of different return intervals on the floodplain and river channel morphological evolution with the associated sediment transport processes are not well explored. Furthermore, different basin management action plans, such as engineering structure modifications, may also greatly affect the flood inundation, sediment transport, solute transport and morphological processes within extreme flood events. In this study, a coupled two-dimensional hydrodynamic, sediment transport and morphological model is applied to evaluate the impact of different river and basin management strategies on the flood inundation, sediment transport dynamics and morphological changes within extreme flood events of different magnitudes. The 10-year, 50-year, 100-year and 200-year floods are evaluated for the Lower Cache Creek system in California under existing condition and a potential future modification scenario. Modeling results showed that select locations of flood inundation within the study area tend to experience larger inundation depth and more sediment is likely to be trapped in the study area under potential modification scenario. The proposed two dimensional flow and sediment transport modeling approach implemented with a variety of inflow conditions can provide guidance to decision-makers when considering implementation of potential modification plans, especially as they relate to competing management strategies of large water bodies, such as the modeling area in this study. Copyright © 2017 Elsevier B.V. All rights reserved.

Flood-inundation maps for the Meramec River at Valley Park and at Fenton, Missouri, 2017

USGS Publications Warehouse

Dietsch, Benjamin J.; Sappington, Jacob N.

2017-09-29

Two sets of digital flood-inundation map libraries that spanned a combined 16.7-mile reach of the Meramec River that extends upstream from Valley Park, Missouri, to downstream from Fenton, Mo., were created by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army Corps of Engineers, St. Louis Metropolitan Sewer District, Missouri Department of Transportation, Missouri American Water, and Federal Emergency Management Agency Region 7. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at https://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the cooperative USGS streamgages on the Meramec River at Valley Park, Mo., (USGS station number 07019130) and the Meramec River at Fenton, Mo. (USGS station number 07019210). Near-real-time stage data at these streamgages may be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/nwis or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at these sites (listed as NWS sites vllm7 and fnnm7, respectively).Flood profiles were computed for the stream reaches by means of a calibrated one-dimensional step-backwater hydraulic model. The model was calibrated using a stage-discharge relation at the Meramec River near Eureka streamgage (USGS station number 07019000) and documented high-water marks from the flood of December 2015 through January 2016.The calibrated hydraulic model was used to compute two sets of water-surface profiles: one set for the streamgage at Valley Park, Mo. (USGS station number 07019130), and one set for the USGS streamgage on the Meramec River at Fenton, Mo. (USGS station number 07019210). The water-surface profiles were produced for stages at 1-foot (ft) intervals referenced to the datum from each streamgage and ranging from the NWS action stage, or near bankfull discharge, to the stage corresponding to the estimated 0.2-percent annual exceedance probability (500-year recurrence interval) flood, as determined at the Eureka streamgage (USGS station number 07019000). The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging data having a 0.28-ft vertical accuracy and 3.28-ft horizontal resolution) to delineate the area flooded at each flood stage (water level).The availability of these maps, along with internet information regarding current stage from the USGS streamgages and forecasted high-flow stages from the NWS, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures and for postflood recovery efforts.

Assessment of the Relationship between Andean Ice Core Precipitation Indicators and Amazon River Discharge

NASA Astrophysics Data System (ADS)

Johnson, N.; Alsdorf, D.; Thompson, L.; Mosley-Thompson, E.; Melack, J.

2006-12-01

Prior to the last 100 years, there is a significant lack of hydrologic knowledge for the Amazon Basin. A 100- year record of discharge from the city of Manaus, located at the confluence of the Solimoes and Negro rivers, is the most complete record for the basin. Inundated wetlands play a key role in carbon out-gassing to the atmosphere whereas discharge from the Amazon River contributes about 20% of the total freshwater flux delivered to the world's oceans. As discharge (Q) and inundation are directly related to precipitation, we are developing a method to extend our understanding of Q and inundation into the 19^{th} century. Using proxy data preserved in Andean glaciers and ice caps and recovered from ice cores, annually resolved histories of δ^{18)O and mass accumulation are available. The latter is a proxy for local precipitation amount whereas δ18O is influenced by continental scale processes (i.e., evaporation, convection) as well as by temperature and hence, by varying climate regimes. We have correlated the accumulation and δ18O records from Core 1 drilled on the Quelccaya ice-cap in the southern Andes of Peru with the Manaus discharge data. As ice core annual layers correspond to the thermal year (in Peru, July to June of the following year) and the discharge records are kept daily (January to December), we averaged 365 days of Q data seeking the optimal correlation for each start and end date. The best statistical relationship between δ18O and Q (r = -0.41, p = < 0.001) is attained when Q is averaged from March 16 to March 15 of the following year. We also correlated 23 years of ENSO events, which are linked to both Amazon River discharge and ice core δ18O (r = -0.60, p = < 0.001). These linear relationships are used to create Amazon discharge for the 20^{th} century and to extrapolate Q into the 19^{th} century. Previously developed relationships between Q and mainstem inundated area are then used to estimate inundated area along the main Amazon channel for the past 200 years. The ice core-derived estimate of inundated area for the past 100 years compares well with the previous and more straightforward estimates based on discharge and remote sensing data.

Open-Source Digital Elevation Model (DEMs) Evaluation with GPS and LiDAR Data

NASA Astrophysics Data System (ADS)

Khalid, N. F.; Din, A. H. M.; Omar, K. M.; Khanan, M. F. A.; Omar, A. H.; Hamid, A. I. A.; Pa'suya, M. F.

2016-09-01

Advanced Spaceborne Thermal Emission and Reflection Radiometer-Global Digital Elevation Model (ASTER GDEM), Shuttle Radar Topography Mission (SRTM), and Global Multi-resolution Terrain Elevation Data 2010 (GMTED2010) are freely available Digital Elevation Model (DEM) datasets for environmental modeling and studies. The quality of spatial resolution and vertical accuracy of the DEM data source has a great influence particularly on the accuracy specifically for inundation mapping. Most of the coastal inundation risk studies used the publicly available DEM to estimated the coastal inundation and associated damaged especially to human population based on the increment of sea level. In this study, the comparison between ground truth data from Global Positioning System (GPS) observation and DEM is done to evaluate the accuracy of each DEM. The vertical accuracy of SRTM shows better result against ASTER and GMTED10 with an RMSE of 6.054 m. On top of the accuracy, the correlation of DEM is identified with the high determination of coefficient of 0.912 for SRTM. For coastal zone area, DEMs based on airborne light detection and ranging (LiDAR) dataset was used as ground truth data relating to terrain height. In this case, the LiDAR DEM is compared against the new SRTM DEM after applying the scale factor. From the findings, the accuracy of the new DEM model from SRTM can be improved by applying scale factor. The result clearly shows that the value of RMSE exhibit slightly different when it reached 0.503 m. Hence, this new model is the most suitable and meets the accuracy requirement for coastal inundation risk assessment using open source data. The suitability of these datasets for further analysis on coastal management studies is vital to assess the potentially vulnerable areas caused by coastal inundation.

Integrating Radarsat-2, Lidar, and Worldview-3 Imagery to maximize detection of forested inundation extent in the Delmarva Peninsula, USA

USGS Publications Warehouse

Vanderhoof, Melanie; Distler, Hayley; Mendiola, Di Ana; Lang, Megan

2017-01-01

Natural variability in surface-water extent and associated characteristics presents a challenge to gathering timely, accurate information, particularly in environments that are dominated by small and/or forested wetlands. This study mapped inundation extent across the Upper Choptank River Watershed on the Delmarva Peninsula, occurring within both Maryland and Delaware. We integrated six quad-polarized Radarsat-2 images, Worldview-3 imagery, and an enhanced topographic wetness index in a random forest model. Output maps were filtered using light detection and ranging (lidar)-derived depressions to maximize the accuracy of forested inundation extent. Overall accuracy within the integrated and filtered model was 94.3%, with 5.5% and 6.0% errors of omission and commission for inundation, respectively. Accuracy of inundation maps obtained using Radarsat-2 alone were likely detrimentally affected by less than ideal angles of incidence and recent precipitation, but were likely improved by targeting the period between snowmelt and leaf-out for imagery collection. Across the six Radarsat-2 dates, filtering inundation outputs by lidar-derived depressions slightly elevated errors of omission for water (+1.0%), but decreased errors of commission (−7.8%), resulting in an average increase of 5.4% in overall accuracy. Depressions were derived from lidar datasets collected under both dry and average wetness conditions. Although antecedent wetness conditions influenced the abundance and total area mapped as depression, the two versions of the depression datasets showed a similar ability to reduce error in the inundation maps. Accurate mapping of surface water is critical to predicting and monitoring the effect of human-induced change and interannual variability on water quantity and quality.

Accessibility assessment of Houston's roadway network during Harvey through integration of observed flood impacts and hydrologic modeling

NASA Astrophysics Data System (ADS)

Gidaris, I.; Gori, A.; Panakkal, P.; Padgett, J.; Bedient, P. B.

2017-12-01

The record-breaking rainfall produced over the Houston region by Hurricane Harvey resulted in catastrophic and unprecedented impacts on the region's infrastructure. Notably, Houston's transportation network was crippled, with almost every major highway flooded during the five-day event. Entire neighborhoods and subdivisions were inundated, rendering them completely inaccessible to rescue crews and emergency services. Harvey has tragically highlighted the vulnerability of major thoroughfares, as well as neighborhood roads, to severe inundation during extreme precipitation events. Furthermore, it has emphasized the need for detailed accessibility characterization of road networks under extreme event scenarios in order to determine which areas of the city are most vulnerable. This analysis assesses and tracks the accessibility of Houston's major highways during Harvey's evolution by utilizing road flood/closure data from the Texas DOT. In the absence of flooded/closure data for local roads, a hybrid approach is adopted that utilizes a physics-based hydrologic model to produce high-resolution inundation estimates for selected urban watersheds in the Houston area. In particular, hydrologic output in the form of inundation depths is used to estimate the operability of local roads. Ultimately, integration of hydrologic-based estimation of road conditions with observed data from DOT supports a network accessibility analysis of selected urban neighborhoods. This accessibility analysis can identify operable routes for emergency response (rescue crews, medical services, etc.) during the storm event.

Habitability at the frontlines of sea level rise: a spatiotemporal analysis of settlements and coastal inundation in eight global sea level rise hotspots between 1990 and 2015

NASA Astrophysics Data System (ADS)

Rose, S. A.; Wrathall, D.

2017-12-01

Over the coming centuries and millennia, sea level rise will greatly redistribute global human population through displacement and migration. Sudden, large-scale displacement is extremely disruptive to society both for migrants and host communities, and there is a great scientific and policy need to anticipate where, when and how this could happen around sea level rise. We can meet these needs by examining how long-term coastal inundation of settlements has already occurred. Using two global geospatial data sets, the Global Human Settlement Layer and the Global Surface Water Layer, we examine the global spatial concentration of settlement inundation that occurred between 1990 and 2015. We focus on the eight sea level rise hotspots identified in Clark et al (2016), which include Bangladesh, Mekong Delta, Indonesia, Japan, Nile Delta, Philippines, and the US Mid-Atlantic and Gulf of Mexico, and examine areas of convergence between settlement loss density and negative population change. This analysis reveals specific areas of concern within vulnerable countries, and forms the basis for focused investigations of the long-term impact of coastal inundation on various migration systems. This analysis shows us how long-term sets of satellite derived data on human population can help anticipate how sea level rise will alter future patterns of human settlement and migration into the 21st century and beyond.

Impact of Sea Level Rise on Storm Surge and Inundation in the Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Veeramony, J.

2016-12-01

Assessing the impact of climate change on surge and inundation due to tropical cyclones is important for coastal adaptation as well as mitigation efforts. Changes in global climate increase vulnerability of coastal environments to the threat posed by severe storms in a number of ways. Both the intensity of future storms as well as the return periods of more severe storms are expected to increase signficantly. Increasing mean sea levels lead to more areas being inundated due to storm surge and bring the threat of inundation further inland. Rainfall associated with severe storms are also expected to increase substantially, which will add to the intensity of inland flooding and coastal inundation. In this study, we will examine the effects of sea level rise and increasing rainfall intensity using Hurricane Ike as the baseline. The Delft3D modeling system will be set up in nested mode, with the outermost nest covering the Gulf of Mexico. The system will be run in a coupled mode, modeling both waves and the hydrodynamics. The baseline simulation will use the atmospheric forcing which consists of the NOAA H*Wind (Powell et all 1998) for the core hurricane characteristics blended with reanalyzed background winds to create a smooth wind field. The rainfall estimates are obtained from TRMM. From this baseline, a set of simulations will be performed to show the impact of sea level rise and increased rainfall activity on flooding and inundation along theTexas-Lousiana coast.

Predicting sea-level rise vulnerability of terrestrial habitat and wildlife of the Northwestern Hawaiian Islands

USGS Publications Warehouse

Reynolds, Michelle H.; Berkowitz, Paul; Courtot, Karen N.; Krause, Crystal M.; Reynolds, Michelle H.; Berkowitz, Paul; Courtot, Karen N.; Krause, Crystal M.

2012-01-01

If current climate change trends continue, rising sea levels may inundate low-lying islands across the globe, placing island biodiversity at risk. Recent models predict a rise of approximately one meter (1 m) in global sea level by 2100, with larger increases possible in areas of the Pacific Ocean. Pacific Islands are unique ecosystems home to many endangered endemic plant and animal species. The Northwestern Hawaiian Islands (NWHI), which extend 1,930 kilometers (km) beyond the main Hawaiian Islands, are a World Heritage Site and part of the Papahanaumokuakea Marine National Monument. These NWHI support the largest tropical seabird rookery in the world, providing breeding habitat for 21 species of seabirds, 4 endemic land bird species and essential foraging, breeding, or haul-out habitat for other resident and migratory wildlife. In recent years, concern has grown about the increasing vulnerability of the NWHI and their wildlife populations to changing climatic patterns, particularly the uncertainty associated with potential impacts from global sea-level rise (SLR) and storms. In response to the need by managers to adapt future resource protection strategies to climate change variability and dynamic island ecosystems, we have synthesized and down scaled analyses for this important region. This report describes a 2-year study of a remote northwestern Pacific atoll ecosystem and identifies wildlife and habitat vulnerable to rising sea levels and changing climate conditions. A lack of high-resolution topographic data for low-lying islands of the NWHI had previously precluded an extensive quantitative model of the potential impacts of SLR on wildlife habitat. The first chapter (chapter 1) describes the vegetation and topography of 20 islands of Papahanaumokuakea Marine National Monument, the distribution and status of wildlife populations, and the predicted impacts for a range of SLR scenarios. Furthermore, this chapter explores the potential effects of SLR on wildlife breeding habitats for each island. The subsequent chapter (chapter 2) details a study of the Laysan Island ecosystem, describing a quantitative model that incorporates SLR, storm wave, and rising groundwater inundation. Wildlife, storm, and oceanographic data allowed for an assessment of the phenological and spatial vulnerability of Laysan Island's breeding bird species to SLR and storms. Using remote sensing and geospatial techniques, we estimated topography, classified vegetation, modeled SLR, and evaluated a range of climate change scenarios. On the basis of high-resolution airborne data collected during 2010-11 (root-mean-squared error = 0.05-0.18 m), we estimated the maximum elevation of 20 individual islands extending from Kure Atoll to French Frigate Shoals (range: 1.8-39.7 m) and computed the mean elevation (1.7 m, standard deviation 1.1 m) across all low-lying islands. We also analyzed general climate models to describe rainfall and temperature scenarios expected to influence adaptation of some plants and animals for this region. Outcomes for the NWHI predicted an increase in temperature of 1.8-2.6 degrees Celsius (°C) and an annual decrease in precipitation of 24.7-76.3 millimeters (mm) across the NWHI by 2100. Our models of passive SLR (excluding wave-driven effects, erosion, and accretion) showed that approximately 4 percent of the total land area in the NWHI will be lost with scenarios of +1.0 m of SLR and 26 percent will be lost with +2.0 m of SLR. Some atolls are especially vulnerable to SLR. For example, at Pearl and Hermes Atoll our analysis indicated substantial habitat losses with 43 percent of the land area inundated at +1.0 m SLR and 92 percent inundated at +2.0 m SLR. Across the NWHI, seven islands will be completely submerged with +2.0 m SLR. The limited global ranges of some tropical nesting birds make them particularly vulnerable to climate change impacts in the NWHI. Climate change scenarios and potential SLR impacts presented here emphasize the need for early climate change adaptation and mitigation planning, especially for species with limited breeding distributions and/or ranges restricted primarily to the low-lying NWHI: Cyperus pennatiformis var. bryanii, Black-footed Albatross (Phoebastria nigripes), Laysan Albatross (P. immutabilis), Bonin Petrel (Pterodroma hypoleuca), Gray-backed Tern (Onychoprion lunatus), Laysan Teal (Anas laysanensis), Laysan Finch (Telespiza cantans), and Hawaiian monk seal (Monachus schauinslandi). Furthermore, SLR scenarios that include the effects of wave dynamics and groundwater rise may indicate amplified vulnerability to climate change driven habitat loss on low-lying islands. In chapter 2, we incorporated the combined effects of SLR, dynamic wave-driven inundation, and rising groundwater in a quantitative study specifically for the Laysan Island ecosystem. This is the first hydrodynamic model to simulate the combined impacts of SLR and wave-driven inundation in the NWHI. We developed a high-resolution digital elevation model (mean vertical accuracy of 0.32 m) for the island. Then using recent satellite imagery, geospatial models, and historical oceanographic, storm, and biological data we estimated potential inundation extent, habitat loss, and wildlife population impacts for a range of potential SLR scenarios (0.00, +0.50, +1.00, +1.50, and +2.00 m) that may occur over the next century. Additionally, we estimated the carrying capacity of Laysan Island for five species based on the available population monitoring data and described how potential losses in nesting habitat could influence population dynamics for Black-footed Albatross, Laysan Albatross, Red-footed Booby (Sula sula), Laysan Teal, and Laysan Finch. For some other seabird populations (Masked Booby, S. dactylatra; Brown Booby, S. leucogaster; Great Frigatebird, Fregata minor; and Sooty Tern, Onychoprion fuscata), we used recent colony distribution data, land cover maps, and nesting behavior to estimate potential losses of nesting habitat from SLR and wave-driven inundation. We observed far greater potential impacts of SLR to wildlife with the dynamic wave-driven modeling approach than with the passive modeling approach. Depending on SLR scenario and coastal orientation, during storms under a +2.00 m SLR scenario, the wave-driven inundation model predicted three times more inundation than the passive model (17.2 percent of total terrestrial area versus 4.6 percent, respectively). Large-wave events generally added 1 m of water height to passive inundation surfaces, therefore our dynamic models (during storm events) forecasted comparable inundation extents earlier than passive models. Although wave-driven water levels were highest in the northwest quadrant of Laysan Island, the greatest extent of inundation occurred in the southeast where coastal dunes less than 3 m above mean sea level provide little protection from wave-driven inundation. When wave-driven inundation was included in the SLR model for Laysan Island greater nesting habitat loss and potential impacts on wildlife population dynamics were predicted. The consequences of habitat loss due to SLR may be worse for species with colonies in the wave-exposed coastal zones (for example, Black-footed Albatross) and for populations already near the island's carrying capacity (for example, Laysan Teal). Species whose peak incubation and chick-rearing periods coincide with seasonally high wave heights also will be increasingly vulnerable, especially those species nesting on the ground in areas vulnerable to inundation, such as Gray-backed Tern and Black-footed Albatross. Other species that have space for population growth, or are not restricted to a narrow range of habitat types on Laysan (for instance, Sooty Terns), may be less sensitive to habitat loss from SLR over the next century. Our assessments of inundation risk, habitat loss, and wildlife species vulnerability synthesize current knowledge about individual islands and contribute to a broader understanding of the impacts of inundation from SLR and storm-induced waves. Yet, most NWHI and their bird populations lack monitoring data to evaluate adaptations to and impacts of climate change. Exceptions include some data sets from long-term monitoring of wildlife populations, tides, or weather at French Frigate Shoals, Laysan Island, and Midway Atoll. These data sets are potentially valuable baselines, which could be informative for adaptive learning (integrating management and science) to predict, adapt, and mitigate the effects of climate change on NWHI wildlife in the future. This study provides the first quantitative vulnerability assessment for all of the low-lying NWHI, and results identify biological communities, locales, and resident endangered species of Papahanaumokuakea Marine National Monument expected to be at risk from SLR. This report is also intended as a reference for managers and conservation planners, a tool to identify and potentially reduce uncertainty, and a starting place for developing climate change monitoring priorities and future scientific studies.

Mobility statistics and automated hazard mapping for debris flows and rock avalanches

USGS Publications Warehouse

Griswold, Julia P.; Iverson, Richard M.

2008-01-01

Power-law equations that are physically motivated and statistically tested and calibrated provide a basis for forecasting areas likely to be inundated by debris flows, rock avalanches, and lahars with diverse volumes. The equations A=α1V2/3 and B=α2V2/3 are based on the postulate that the maximum valley cross-sectional area (A) and total valley planimetric area (B) likely to be inundated by a flow depend only on its volume (V) and the topography of the flow path. Testing of these equations involves determining whether or not they fit data for documented flows satisfactorily, and calibration entails determining best-fit values of the coefficients α1 and α2 for debris flows, rock avalanches, and lahars. This report describes statistical testing and calibration of the equations by using field data compiled from many sources, and it describes application of the equations to delineation of debris-flow hazard zones. Statistical results show that for each type of flow (debris flows, rock avalanches, and lahars), the dependence of A and B on V is described well by power laws with exponents equal to 2/3. This value of the exponent produces fits that are effectively indistinguishable from the best fits obtained by using adjustable power-law exponents. Statistically calibrated values of the coefficients α1 and α2 provide scale-invariant indices of the relative mobilities of rock avalanches (α1 = 0.2, α2 = 20), nonvolcanic debris flows (α1 = 0.1, α2 = 20), and lahars (α1 = 0.05, α2 = 200). These values show, for example, that a lahar of specified volume can be expected to inundate a planimetric area ten times larger than that inundated by a rock avalanche or nonvolcanic debris flow of the same volume. The utility of the calibrated debris-flow inundation equations A=0.1V2/3 and B=20V2/3 is demonstrated by using them within the GIS program LAHARZ to delineate nested hazard zones for future debris flows in an area bordering the Umpqua River in the south-central Oregon Coast Range. This application requires use of high-resolution topographic data derived form LIDAR surveys, knowledge of local geology to specify a suitable range of prospective debris-flow volumes, and development and use of a new algorithm for identification of prospective debris-flow source areas in finely dissected terrain.

Comparison of 2D numerical models for river flood hazard assessment: simulation of the Secchia River flood in January, 2014

NASA Astrophysics Data System (ADS)

Shustikova, Iuliia; Domeneghetti, Alessio; Neal, Jeffrey; Bates, Paul; Castellarin, Attilio

2017-04-01

Hydrodynamic modeling of inundation events still brings a large array of uncertainties. This effect is especially evident in the models run for geographically large areas. Recent studies suggest using fully two-dimensional (2D) models with high resolution in order to avoid uncertainties and limitations coming from the incorrect interpretation of flood dynamics and an unrealistic reproduction of the terrain topography. This, however, affects the computational efficiency increasing the running time and hardware demands. Concerning this point, our study evaluates and compares numerical models of different complexity by testing them on a flood event that occurred in the basin of the Secchia River, Northern Italy, on 19th January, 2014. The event was characterized by a levee breach and consequent flooding of over 75 km2 of the plain behind the dike within 48 hours causing population displacement, one death and economic losses in excess of 400 million Euro. We test the well-established TELEMAC 2D, and LISFLOOD-FP codes, together with the recently launched HEC-RAS 5.0.3 (2D model), all models are implemented using different grid size (2-200 m) based on the 1 m digital elevation model resolution. TELEMAC is a fully 2D hydrodynamic model which is based on the finite-element or finite-volume approach. Whereas HEC-RAS 5.0.3 and LISFLOOD-FP are both coupled 1D-2D models. All models are calibrated against observed inundation extent and maximum water depths, which are retrieved from remotely sensed data and field survey reports. Our study quantitatively compares the three modeling strategies highlighting differences in terms of the ease of implementation, accuracy of representation of hydraulic processes within floodplains and computational efficiency. Additionally, we look into the different grid resolutions in terms of the results accuracy and computation time. Our study is a preliminary assessment that focuses on smaller areas in order to identify potential modeling schemes that would be efficient for simulating flooding scenarios for large and very large floodplains. This research aims at contributing to the reduction of uncertainties and limitations in hazard and risk assessment.

Reconstruction of the effects of the 2004 Sumatra tsunami on the peculiar morphology of the Seychelles Islands: an application to the island of Praslin

NASA Astrophysics Data System (ADS)

Tonini, R.; Tinti, S.; Pagnoni, G.; Gallazzi, S. C.; Armigliato, A.

2009-12-01

The Seychelles archipelago is located 1600 km east to the African coasts, in front of Kenya. The 26 December 2004 Sumatra tsunami hit these islands killing two people and causing huge damage to structures and facilities. The impact was more moderate than it could be, because the highest waves arrived during the lowest tide cycle. The difference between low and high tide is about 1.4 meters and this situation limited substantially the inundation inland. The maximun observed runups were no greater than 4 meters above sea level. All the Seychelles islands lie on a very shallow platform. This platform differentiates from the surrounding sea bottom with a rapid change of the bathymetry that leads the ocean depth from 2 km to 70-80 m over a very short horizontal distance. This peculiar morphology of the bathymetry has very interesting effects on the tsunami propagation. In facts the platform is capable of modifying significantly the tsunami signal with respect to the surrounding open sea. The main island of the archipelago is Mahé. Here the tsunami was recorded by the Pointe La Rue station that is located at the end of the international airport in the east side of the island. Praslin is the second largest island of the group of the Seychelles Archipelago and it was chosen as benchmark for testing numerical models by the research teams involved in the framework of the EU-funded SCHEMA (Scenarios for Hazard-induced Emergencies Management) project. The Tsunami Research Team of the Bologna University, Italy, is partner in the project and here it presents the results obtained for Praslin, computing the inundation maps for the 2004 case, basing on the source model proposed by PMEL/NOAA (M=9.3, average slip 18 m, L=700 km, W=100-150 km). Here we present the results concerning the propagation and inundation in the island of Praslin that have been computed by means of the UBO-TSUFD code developed and maintained by the Tsunami Research Team of the University of Bologna. The code solves both linear and non-linear shallow water equations with a leap-frog algorithm over staggered nested grids. The high resolution bathymetry and topography in Praslin island area were provided by the GSC Geosciences Consultant (Bagneux, France), coordinator of SCHEMA. The first goal of the study is trying to reproduce the signal recorded at the Pointe La Rue station in order to test the reliability of the numerical code. Moreover, the effects of the 2004 Sumatra tsunami on the island of Praslin are shown, providing detailed inundation maps and maximum elevation and velocity fields computed with a spatial resolution of 8 meters. Finally, an analysis of the effects of the Seychelles platform on the tsunami is shown and discussed.

Towards a robust framework for Probabilistic Tsunami Hazard Assessment (PTHA) for local and regional tsunami in New Zealand

NASA Astrophysics Data System (ADS)

Mueller, Christof; Power, William; Fraser, Stuart; Wang, Xiaoming

2013-04-01

Probabilistic Tsunami Hazard Assessment (PTHA) is conceptually closely related to Probabilistic Seismic Hazard Assessment (PSHA). The main difference is that PTHA needs to simulate propagation of tsunami waves through the ocean and cannot rely on attenuation relationships, which makes PTHA computationally more expensive. The wave propagation process can be assumed to be linear as long as water depth is much larger than the wave amplitude of the tsunami. Beyond this limit a non-linear scheme has to be employed with significantly higher algorithmic run times. PTHA considering far-field tsunami sources typically uses unit source simulations, and relies on the linearity of the process by later scaling and combining the wave fields of individual simulations to represent the intended earthquake magnitude and rupture area. Probabilistic assessments are typically made for locations offshore but close to the coast. Inundation is calculated only for significantly contributing events (de-aggregation). For local and regional tsunami it has been demonstrated that earthquake rupture complexity has a significant effect on the tsunami amplitude distribution offshore and also on inundation. In this case PTHA has to take variable slip distributions and non-linearity into account. A unit source approach cannot easily be applied. Rupture complexity is seen as an aleatory uncertainty and can be incorporated directly into the rate calculation. We have developed a framework that manages the large number of simulations required for local PTHA. As an initial case study the effect of rupture complexity on tsunami inundation and the statistics of the distribution of wave heights have been investigated for plate-interface earthquakes in the Hawke's Bay region in New Zealand. Assessing the probability that water levels will be in excess of a certain threshold requires the calculation of empirical cumulative distribution functions (ECDF). We compare our results with traditional estimates for tsunami inundation simulations that do not consider rupture complexity. De-aggregation based on moment magnitude alone might not be appropriate, because the hazard posed by any individual event can be underestimated locally if rupture complexity is ignored.

4D Floodplain representation in hydrologic flood forecasting using WRFHydro modeling framework

NASA Astrophysics Data System (ADS)

Gangodagamage, C.; Li, Z.; Adams, T.; Ito, T.; Maitaria, K.; Islam, M.; Dhondia, J.

2015-12-01

Floods claim more lives and damage more property than any other category of natural disaster in the Continental U.S. A system that can demarcate local flood boundaries dynamically could help flood prone communities prepare for and even prevent from catastrophic flood events. Lateral distance from the centerline of the river to the right and left floodplains for the water levels coming out of the models at each grid location have not been properly integrated with the national hydrography dataset (NHDPlus). The NHDPlus dataset represents the stream network with feature classes such as rivers, tributaries, canals, lakes, ponds, dams, coastlines, and stream gages. The NHDPlus dataset consists of approximately 2.7 million river reaches defining how surface water drains to the ocean. These river reaches have upstream and downstream nodes and basic parameters such as flow direction, drainage area, reach slope etc. We modified an existing algorithm (Gangodagamage et al., 2007, 2011) to provide lateral distance from the centerline of the river to the right and left floodplains for the flows simulated by models. Previous work produced floodplain boundaries for static river stages (i.e. 3D metric: distance along the main stem, flow depth, lateral distance from river center line). Our new approach introduces the floodplain boundary for variable water levels with the fourth dimension, time. We use modeled flows from WRFHydro and demarcate the right and left lateral boundaries of inundation dynamically. This approach dynamically integrates with high resolution models (e.g., hourly and ~ 1 km spatial resolution) that are developed from recent advancements in high computational power with ground based measurements (e.g., Fluxnet), lateral inundation vectors (direction and spatial extent) derived from multi-temporal remote sensing data (e.g., LiDAR, WorldView 2, Landsat, ASTER, MODIS), and improved representations of the physical processes through multi-parameterizations. Our approach enhances the normalized (streams are at zero elevations) DEM derived upstream flow routing pathways for stream reaches for given water stages as more and more satellite data become available for various flood inundations. Validation of the inundation boundaries is performed using HEC-RAS hydrodynamic model results for selected streams.

Reduced Complexity Modelling of Urban Floodplain Inundation

NASA Astrophysics Data System (ADS)

McMillan, H. K.; Brasington, J.; Mihir, M.

2004-12-01

Significant recent advances in floodplain inundation modelling have been achieved by directly coupling 1d channel hydraulic models with a raster storage cell approximation for floodplain flows. The strengths of this reduced-complexity model structure derive from its explicit dependence on a digital elevation model (DEM) to parameterize flows through riparian areas, providing a computationally efficient algorithm to model heterogeneous floodplains. Previous applications of this framework have generally used mid-range grid scales (101-102 m), showing the capacity of the models to simulate long reaches (103-104 m). However, the increasing availability of precision DEMs derived from airborne laser altimetry (LIDAR) enables their use at very high spatial resolutions (100-101 m). This spatial scale offers the opportunity to incorporate the complexity of the built environment directly within the floodplain DEM and simulate urban flooding. This poster describes a series of experiments designed to explore model functionality at these reduced scales. Important questions are considered, raised by this new approach, about the reliability and representation of the floodplain topography and built environment, and the resultant sensitivity of inundation forecasts. The experiments apply a raster floodplain model to reconstruct a 1:100 year flood event on the River Granta in eastern England, which flooded 72 properties in the town of Linton in October 2001. The simulations use a nested-scale model to maintain efficiency. A 2km by 4km urban zone is represented by a high-resolution DEM derived from single-pulse LIDAR data supplied by the UK Environment Agency, together with surveyed data and aerial photography. Novel methods of processing the raw data to provide the individual structure detail required are investigated and compared. This is then embedded within a lower-resolution model application at the reach scale which provides boundary conditions based on recorded flood stage. The high resolution predictions on a scale commensurate with urban structures make possible a multi-criteria validation which combines verification of reach-scale characteristics such as downstream flow and inundation extent with internal validation of flood depth at individual sites.

Global hydrodynamic modelling of flood inundation in continental rivers: How can we achieve it?

NASA Astrophysics Data System (ADS)

Yamazaki, D.

2016-12-01

Global-scale modelling of river hydrodynamics is essential for understanding global hydrological cycle, and is also required in interdisciplinary research fields . Global river models have been developed continuously for more than two decades, but modelling river flow at a global scale is still a challenging topic because surface water movement in continental rivers is a multi-spatial-scale phenomena. We have to consider the basin-wide water balance (>1000km scale), while hydrodynamics in river channels and floodplains is regulated by much smaller-scale topography (<100m scale). For example, heavy precipitation in upstream regions may later cause flooding in farthest downstream reaches. In order to realistically simulate the timing and amplitude of flood wave propagation for a long distance, consideration of detailed local topography is unavoidable. I have developed the global hydrodynamic model CaMa-Flood to overcome this scale-discrepancy of continental river flow. The CaMa-Flood divides river basins into multiple "unit-catchments", and assumes the water level is uniform within each unit-catchment. One unit-catchment is assigned to each grid-box defined at the typical spatial resolution of global climate models (10 100 km scale). Adopting a uniform water level in a >10km river segment seems to be a big assumption, but it is actually a good approximation for hydrodynamic modelling of continental rivers. The number of grid points required for global hydrodynamic simulations is largely reduced by this "unit-catchment assumption". Alternative to calculating 2-dimensional floodplain flows as in regional flood models, the CaMa-Flood treats floodplain inundation in a unit-catchment as a sub-grid physics. The water level and inundated area in each unit-catchment are diagnosed from water volume using topography parameters derived from high-resolution digital elevation models. Thus, the CaMa-Flood is at least 1000 times computationally more efficient compared to regional flood inundation models while the reality of simulated flood dynamics is kept. I will explain in detail how the CaMa-Flood model has been constructed from high-resolution topography datasets, and how the model can be used for various interdisciplinary applications.

Topography-based analysis of Hurricane Katrina inundation of New Orleans: Chapter 3G in Science and the storms-the USGS response to the hurricanes of 2005

USGS Publications Warehouse

Gesch, Dean

2007-01-01

The ready availability of high-resolution, high-accuracy elevation data proved valuable for development of topographybased products to determine rough estimates of the inundation of New Orleans, La., from Hurricane Katrina. Because of its high level of spatial detail and vertical accuracy of elevation measurements, light detection and ranging (lidar) remote sensing is an excellent mapping technology for use in low-relief hurricane-prone coastal areas.

Assessing downstream flood impacts due to a potential GLOF from Imja Tsho in Nepal

NASA Astrophysics Data System (ADS)

Somos-Valenzuela, M. A.; McKinney, D. C.; Byers, A. C.; Rounce, D. R.; Portocarrero, C.; Lamsal, D.

2015-03-01

Glacial-dominated areas pose unique challenges to downstream communities in adapting to recent and continuing global climate change, including increased threats of glacial lake outburst floods (GLOFs) that can increase risk due to flooding of downstream communities and cause substantial impacts on regional social, environmental and economic systems. The Imja glacial lake (or Imja Tsho) in Nepal, which has the potential to generate a GLOF, was studied using a two-dimensional debris-flow inundation model in order to evaluate the effectiveness of proposed measures to reduce possible flooding impacts to downstream communities by lowering the lake level. The results indicate that only minor flood impact reduction is achieved in the downstream community of Dingboche with modest (~3 m) lake lowering. Lowering the lake by 10 m shows a significant reduction in inundated area. However, lowering the lake by 20 m almost eliminates all flood impact at Dingboche. Further downstream at Phakding, the impact of the GLOF is significant and similar reductions in inundation are likely as a result of lake lowering.

Water-surface elevations and channel characteristics for selected reaches of the Rogue River and Elk Creek, Jackson and Josephine Counties, Oregon

USGS Publications Warehouse

Harris, D.D.

1970-01-01

The central Rogue River valley, because of its mild climate, fertile soil, scenic attractions, and sport-fishery resource, has great potential for future population growth and industrial development. As the population grows and the area develops, zoning becomes necessary to assure the most beneficial use of the land, especially of the flood plains. To establish land-use zones on the flood plains, the area subject to inundation and elevation of floods must be considered. Areas flooded during the December 1964 flood and the approximate limits of the 1861 flood in Jackson and Josephine Counties are shown in two interim reports (Corps of Engineers, 1965); however, there are no published flood-elevation profiles to use as a basis for establishing meaningful land-use-zone boundaries or for delineating inundated areas of other floods.

Study on Development of 1D-2D Coupled Real-time Urban Inundation Prediction model

NASA Astrophysics Data System (ADS)

Lee, Seungsoo

2017-04-01

In recent years, we are suffering abnormal weather condition due to climate change around the world. Therefore, countermeasures for flood defense are urgent task. In this research, study on development of 1D-2D coupled real-time urban inundation prediction model using predicted precipitation data based on remote sensing technology is conducted. 1 dimensional (1D) sewerage system analysis model which was introduced by Lee et al. (2015) is used to simulate inlet and overflow phenomena by interacting with surface flown as well as flows in conduits. 2 dimensional (2D) grid mesh refinement method is applied to depict road networks for effective calculation time. 2D surface model is coupled with 1D sewerage analysis model in order to consider bi-directional flow between both. Also parallel computing method, OpenMP, is applied to reduce calculation time. The model is estimated by applying to 25 August 2014 extreme rainfall event which caused severe inundation damages in Busan, Korea. Oncheoncheon basin is selected for study basin and observed radar data are assumed as predicted rainfall data. The model shows acceptable calculation speed with accuracy. Therefore it is expected that the model can be used for real-time urban inundation forecasting system to minimize damages.

Delivering integrated HAZUS-MH flood loss analyses and flood inundation maps over the Web.

PubMed

Hearn, Paul P; Longenecker, Herbert E; Aguinaldo, John J; Rahav, Ami N

2013-01-01

Catastrophic flooding is responsible for more loss of life and damages to property than any other natural hazard. Recently developed flood inundation mapping technologies make it possible to view the extent and depth of flooding on the land surface over the Internet; however, by themselves these technologies are unable to provide estimates of losses to property and infrastructure. The Federal Emergency Management Agency's (FEMA's) HAZUS-MH software is extensively used to conduct flood loss analyses in the United States, providing a nationwide database of population and infrastructure at risk. Unfortunately, HAZUS-MH requires a dedicated Geographic Information System (GIS) workstation and a trained operator, and analyses are not adapted for convenient delivery over the Web. This article describes a cooperative effort by the US Geological Survey (USGS) and FEMA to make HAZUS-MH output GIS and Web compatible and to integrate these data with digital flood inundation maps in USGS's newly developed Inundation Mapping Web Portal. By running the computationally intensive HAZUS-MH flood analyses offline and converting the output to a Web-GIS compatible format, detailed estimates of flood losses can now be delivered to anyone with Internet access, thus dramatically increasing the availability of these forecasts to local emergency planners and first responders.

Delivering integrated HAZUS-MH flood loss analyses and flood inundation maps over the Web

USGS Publications Warehouse

Hearn,, Paul P.; Longenecker, Herbert E.; Aguinaldo, John J.; Rahav, Ami N.

2013-01-01

Catastrophic flooding is responsible for more loss of life and damages to property than any other natural hazard. Recently developed flood inundation mapping technologies make it possible to view the extent and depth of flooding on the land surface over the Internet; however, by themselves these technologies are unable to provide estimates of losses to property and infrastructure. The Federal Emergency Management Agency’s (FEMA's) HAZUS-MH software is extensively used to conduct flood loss analyses in the United States, providing a nationwide database of population and infrastructure at risk. Unfortunately, HAZUS-MH requires a dedicated Geographic Information System (GIS) workstation and a trained operator, and analyses are not adapted for convenient delivery over the Web. This article describes a cooperative effort by the US Geological Survey (USGS) and FEMA to make HAZUS-MH output GIS and Web compatible and to integrate these data with digital flood inundation maps in USGS’s newly developed Inundation Mapping Web Portal. By running the computationally intensive HAZUS-MH flood analyses offline and converting the output to a Web-GIS compatible format, detailed estimates of flood losses can now be delivered to anyone with Internet access, thus dramatically increasing the availability of these forecasts to local emergency planners and first responders.

Coupled 1-D sewer and street networks and 2-D flooding model to rapidly evaluate surface inundation

NASA Astrophysics Data System (ADS)

Kao, Hong-Ming; Hsu, Hao-Ming

2017-04-01

Flash floods have occurred frequently in the urban areas around the world and cause the infrastructure and people living to expose continuously in the high risk level of pluvial flooding. According to historical surveys, the major reasons of severe surface inundations in the urban areas can be attributed to heavy rainfall in the short time and/or drainage system failure. In order to obtain real-time flood forecasting with high accuracy and less uncertainty, an appropriate system for predicting floods is necessary. For the reason, this study coupled 1-D sewer and street networks and 2-D flooding model as an operational modelling system for rapidly evaluating surface inundation. The proposed system is constructed by three significant components: (1) all the rainfall-runoff of a sub-catchment collected via gullies is simulated by the RUNOFF module of the Storm Water Management Model (SWMM); (2) and directly drained to the 1-D sewer and street networks via manholes as inflow discharges to conduct flow routing by using the EXTRAN module of SWMM; (3) after the 1-D simulations, the surcharges from manholes are considered as point sources in 2-D overland flow simulations that are executed by the WASH123D model. It can thus be used for urban flood modelling that reflects the rainfall-runoff processes, and the dynamic flow interactions between the storm sewer system and the ground surface in urban areas. In the present study, we adopted the Huwei Science and Technology Park, located in the south-western part of Taiwan, as the demonstration area because of its high industrial values. The region has an area about 1 km2 with approximately 1 km in both length and width. It is as isolated urban drainage area in which there is a complete sewer system that collects the runoff and drains to the detention pond. Based on the simulated results, the proposed modelling system was found that the simulated floods fit to the survey records because the physical rainfall-runoff phenomena in urban environment were better reflected. Keywords: SWMM, WASH123D, surface inundation, real-time.

Development of a model to simulate groundwater inundation induced by sea-level rise and high tides in Honolulu, Hawaii.

PubMed

Habel, Shellie; Fletcher, Charles H; Rotzoll, Kolja; El-Kadi, Aly I

2017-05-01

Many of the world's largest cities face risk of sea-level rise (SLR) induced flooding owing to their limited elevations and proximities to the coastline. Within this century, global mean sea level is expected to reach magnitudes that will exceed the ground elevation of some built infrastructure. The concurrent rise of coastal groundwater will produce additional sources of inundation resulting from narrowing and loss of the vertical unsaturated subsurface space. This has implications for the dense network of buried and low-lying infrastructure that exists across urban coastal zones. Here, we describe a modeling approach that simulates narrowing of the unsaturated space and groundwater inundation (GWI) generated by SLR-induced lifting of coastal groundwater. The methodology combines terrain modeling, groundwater monitoring, estimation of tidal influence, and numerical groundwater-flow modeling to simulate future flood scenarios considering user-specified tide stages and magnitudes of SLR. We illustrate the value of the methodology by applying it to the heavily urbanized and low-lying Waikiki area of Honolulu, Hawaii. Results indicate that SLR of nearly 1 m generates GWI across 23% of the 13 km 2 study area, threatening $5 billion of taxable real estate and 48 km of roadway. Analysis of current conditions reveals that 86% of 259 active cesspool sites in the study area are likely inundated. This suggests that cesspool effluent is currently entering coastal groundwater, which not only leads to degradation of coastal environments, but also presents a future threat to public health as GWI would introduce effluent at the ground surface. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tohoku-Oki Earthquake Tsunami Runup and Inundation Data for Sites Around the Island of Hawaiʻi

USGS Publications Warehouse

Trusdell, Frank A.; Chadderton, Amy; Hinchliffe, Graham; Hara, Andrew; Patenge, Brent; Weber, Tom

2012-01-01

At 0546 U.t.c. March 11, 2011, a Mw 9.0 ("great") earthquake occurred near the northeast coast of Honshu Island, Japan, generating a large tsunami that devastated the east coast of Japan and impacted many far-flung coastal sites around the Pacific Basin. After the earthquake, the Pacific Tsunami Warning Center issued a tsunami alert for the State of Hawaii, followed by a tsunami-warning notice from the local State Civil Defense on March 10, 2011 (Japan is 19 hours ahead of Hawaii). After the waves passed the islands, U.S. Geological Survey (USGS) scientists from the Hawaiian Volcano Observatory (HVO) measured inundation (maximum inland distance of flooding), runup (elevation at maximum extent of inundation) and took photographs in coastal areas around the Island of Hawaiʻi. Although the damage in West Hawaiʻi is well documented, HVO's mapping revealed that East Hawaiʻi coastlines were also impacted by the tsunami. The intent of this report is to provide runup and inundation data for sites around the Island of Hawaiʻi.

Palm Swamp Wetland Ecosystems of the Upper Amazon: Characterizing their Distribution and Inundation State Using Multiple Resolution Microwave Remote Sensing

NASA Astrophysics Data System (ADS)

Podest, E.; McDonald, K. C.; Schröder, R.; Pinto, N.; Zimmermann, R.; Horna, V.

2011-12-01

Palm swamp wetlands are prevalent in the Amazon basin, including extensive regions in northern Peru. These ecosystems are characterized by constant surface inundation and moderate seasonal water level variation. The combination of constantly saturated soils, giving rise to low oxygen conditions, and warm temperatures year-round can lead to considerable methane release to the atmosphere. Because of the widespread occurrence and expected sensitivity of these ecosystems to climate change, knowledge of their spatial extent and inundation state is crucial for assessing the associated land-atmosphere carbon exchange. Precise spatio-temporal information on palm swamps is difficult to gather because of their remoteness and difficult accessibility. Spaceborne microwave remote sensing is an effective tool for characterizing these ecosystems since it is sensitive to surface water and vegetation structure and allows monitoring large inaccessible areas on a temporal basis regardless of atmospheric conditions or solar illumination. We are developing a remote sensing methodology using multiple resolution microwave remote sensing data to determine palm swamp distribution and inundation state over focus regions in the Amazon basin in northern Peru. For this purpose, two types of multi-temporal microwave data are used: 1) high-resolution (100 m) data from the Advanced Land Observing Satellite (ALOS) Phased Array L-Band Synthetic Aperture Radar (PALSAR) to derive maps of palm swamp extent and inundation from dual-polarization fine-beam and multi-temporal HH-polarized ScanSAR, and 2) coarse resolution (25 km) combined active and passive microwave data from QuikSCAT and AMSR-E to derive inundated area fraction on a weekly basis. We compare information content and accuracy of the coarse resolution products to the PALSAR-based datasets to ensure information harmonization. The synergistic combination of high and low resolution datasets will allow for characterization of palm swamps and assessment of their flooding status. This work has been undertaken partly within the framework of the JAXA ALOS Kyoto & Carbon Initiative. PALSAR data have been provided by JAXA/EORC. Portions of this work were carried out at the Jet Propulsion Laboratory, California Institute of Technology, under contract with the National Aeronautics and Space Administration.

Application of Spatial Neural Network Model for Optimal Operation of Urban Drainage System

NASA Astrophysics Data System (ADS)

KIM, B. J.; Lee, J. Y.; KIM, H. I.; Son, A. L.; Han, K. Y.

2017-12-01

The significance of real-time operation of drainage pump and warning system for inundation becomes recently increased in order to coping with runoff by high intensity precipitation such as localized heavy rain that frequently and suddenly happen. However existing operation of drainage pump station has been made a decision according to opinion of manager based on stage because of not expecting exact time that peak discharge occur in pump station. Therefore the scale of pump station has been excessively estimated. Although it is necessary to perform quick and accurate inundation in analysis downtown area due to huge property damage from flood and typhoon, previous studies contained risk deducting incorrect result that differs from actual result owing to the diffusion aspect of flow by effect on building and road. The purpose of this study is to develop the data driven model for the real-time operation of drainage pump station and two-dimensional inundation analysis that are improved the problems of the existing hydrology and hydrological model. Neuro-Fuzzy system for real time prediction about stage was developed by estimating the type and number of membership function. Based on forecasting stage, it was decided when pump machine begin to work and how much water scoop up by using penalizing genetic algorithm. It is practicable to forecast stage, optimize pump operation and simulate inundation analysis in real time through the methodologies suggested in this study. This study can greatly contribute to the establishment of disaster information map that prevent and mitigate inundation in urban drainage area. The applicability of the development model for the five drainage pump stations in the Mapo drainage area was verified. It is considered to be able to effectively manage urban drainage facilities in the development of these operating rules. Keywords : Urban flooding; Geo-ANFIS method; Optimal operation; Drainage system; AcknowlegementThis research was supported by a grant (17AWMP-B079625-04) from Water Management Research Program funded by Ministry of Land, Infrastructure and Transport of Korean government.

WRF-Chem simulations in the Amazon region during wet and dry season transitions: evaluation of methane models and wetland inundation maps

NASA Astrophysics Data System (ADS)

Beck, V.; Gerbig, C.; Koch, T.; Bela, M. M.; Longo, K. M.; Freitas, S. R.; Kaplan, J. O.; Prigent, C.; Bergamaschi, P.; Heimann, M.

2012-09-01

The Amazon region as a large source of methane (CH4) contributes significantly to the global annual CH4 budget. For the first time in the Amazon region, a forward and inverse modelling framework on regional scale for the purpose of assessing the CH4 budget of the Amazon region is implemented. Here, we present forward simulations of CH4 based on a modified version of the Weather Research and Forecasting model with chemistry that allows for passive tracer transport of CH4, carbon monoxide, and carbon dioxide (WRF-GHG), in combination with two different process-based bottom-up models of CH4 emissions from anaerobic microbial production in wetlands and additional datasets prescribing CH4 emissions from other sources such as biomass burning, termites, or other anthropogenic emissions. We compare WRF-GHG simulations on 10 km horizontal resolution to flask and continuous CH4 observations obtained during two airborne measurement campaigns within the Balanço Atmosférico Regional de Carbono na Amazônia (BARCA) project in November 2008 and May 2009. In addition, three different wetland inundation maps, prescribing the fraction of inundated area per grid cell, are evaluated. Our results indicate that the wetland inundation map with inundated area changing in time represents the observations best except for the northern part of the Amazon basin and the Manaus area. WRF-GHG was able to represent the observed CH4 mixing ratios best at days with less convective activity. After adjusting wetland emissions to match the averaged observed mixing ratios of flights with little convective activity, the monthly CH4 budget of the Amazon lowland region obtained from four different simulations ranges from 1.5 to 4.8 Tg for November 2008 and from 1.3 to 5.5 Tg for May 2009. This corresponds to an average CH4 flux of 9-31 mg m-2 d-1 for November 2008 and 8-36 mg m-2 d-1 for May 2009.

A multi-sensor data-driven methodology for all-sky passive microwave inundation retrieval

NASA Astrophysics Data System (ADS)

Takbiri, Zeinab; Ebtehaj, Ardeshir M.; Foufoula-Georgiou, Efi

2017-06-01

We present a multi-sensor Bayesian passive microwave retrieval algorithm for flood inundation mapping at high spatial and temporal resolutions. The algorithm takes advantage of observations from multiple sensors in optical, short-infrared, and microwave bands, thereby allowing for detection and mapping of the sub-pixel fraction of inundated areas under almost all-sky conditions. The method relies on a nearest-neighbor search and a modern sparsity-promoting inversion method that make use of an a priori dataset in the form of two joint dictionaries. These dictionaries contain almost overlapping observations by the Special Sensor Microwave Imager and Sounder (SSMIS) on board the Defense Meteorological Satellite Program (DMSP) F17 satellite and the Moderate Resolution Imaging Spectroradiometer (MODIS) on board the Aqua and Terra satellites. Evaluation of the retrieval algorithm over the Mekong Delta shows that it is capable of capturing to a good degree the inundation diurnal variability due to localized convective precipitation. At longer timescales, the results demonstrate consistency with the ground-based water level observations, denoting that the method is properly capturing inundation seasonal patterns in response to regional monsoonal rain. The calculated Euclidean distance, rank-correlation, and also copula quantile analysis demonstrate a good agreement between the outputs of the algorithm and the observed water levels at monthly and daily timescales. The current inundation products are at a resolution of 12.5 km and taken twice per day, but a higher resolution (order of 5 km and every 3 h) can be achieved using the same algorithm with the dictionary populated by the Global Precipitation Mission (GPM) Microwave Imager (GMI) products.

Measurement of stream channel habitat using sonar

USGS Publications Warehouse

Flug, Marshall; Seitz, Heather; Scott, John

1998-01-01

An efficient and low cost technique using a sonar system was evaluated for describing channel geometry and quantifying inundated area in a large river. The boat-mounted portable sonar equipment was used to record water depths and river width measurements for direct storage on a laptop computer. The field data collected from repeated traverses at a cross-section were evaluated to determine the precision of the system and field technique. Results from validation at two different sites showed average sample standard deviations (S.D.s) of 0.12 m for these complete cross-sections, with coefficient of variations of 10%. Validation using only the mid-channel river cross-section data yields an average sample S.D. of 0.05 m, with a coefficient of variation below 5%, at a stable and gauged river site using only measurements of water depths greater than 0.6 m. Accuracy of the sonar system was evaluated by comparison to traditionally surveyed transect data from a regularly gauged site. We observed an average mean squared deviation of 46.0 cm2, considering only that portion of the cross-section inundated by more than 0.6 m of water. Our procedure proved to be a reliable, accurate, safe, quick, and economic method to record river depths, discharges, bed conditions, and substratum composition necessary for stream habitat studies.

Physical and Economic Impacts of Sea-Level Rise and Low Probability Flooding Events on Coastal Communities

PubMed Central

Prime, Thomas; Brown, Jennifer M.; Plater, Andrew J.

2015-01-01

Conventionally flood mapping typically includes only a static water level (e.g. peak of a storm tide) in coastal flood inundation events. Additional factors become increasingly important when increased water-level thresholds are met during the combination of a storm tide and increased mean sea level. This research incorporates factors such as wave overtopping and river flow in a range of flood inundation scenarios of future sea-level projections for a UK case study of Fleetwood, northwest England. With increasing mean sea level it is shown that wave overtopping and river forcing have an important bearing on the cost of coastal flood events. The method presented converts inundation maps into monetary cost. This research demonstrates that under scenarios of joint extreme surge-wave-river events the cost of flooding can be increased by up to a factor of 8 compared with an increase in extent of up to a factor of 3 relative to “surge alone” event. This is due to different areas being exposed to different flood hazards and areas with common hazard where flood waters combine non-linearly. This shows that relying simply on flood extent and volume can under-predict the actual economic impact felt by a coastal community. Additionally, the scenario inundation depths have been presented as “brick course” maps, which represent a new way of interpreting flood maps. This is primarily aimed at stakeholders to increase levels of engagement within the coastal community. PMID:25710497

Typhoon Doksuri Flooding in 2017 - High-Resolution Inundation Mapping and Monitoring from Sentinel Satellite SAR Data

NASA Astrophysics Data System (ADS)

Nghiem, S. V.; Nguyen, D. T.

2017-12-01

In 2017, typhoons and hurricanes have inflicted catastrophic flooding across extensive regions in many countries on several continents, including Asia and North America. The U.S. Federal Emergency Management Agency (FEMA) requested urgent support for flood mapping and monitoring in an emergency response to the devastating flood situation. An innovative satellite remote sensing method, called the Depolarization Reduction Algorithm for Global Observations of inundatioN (DRAGON), has been developed and implemented for use with Sentinel synthetic aperture radar (SAR) satellite data at a resolution of 10 meters to identify, map, and monitor inundation including pre-existing water bodies and newly flooded areas. Because Sentinel SAR operates at C-band microwave frequency, it can be used for flood mapping regardless of could cover conditions typically associated with storms, and thus can provide immediate results without the need to wait for the clouds to clear out. In Southeast Asia, Typhoon Doksuri caused significant flooding across extensive regions in Vietnam and other countries in September 2017. Figure 1 presents the flood mapping result over a region around Hà Tĩnh (north central coast of Vietnam) showing flood inundated areas (in yellow) on 16 September 2017 together with pre-existing surface water (in blue) on 4 September 2017. This is just one example selected from a larger flood map covering an extensive region of about 250 km x 680 km all along the central coast of Vietnam.

Physical and economic impacts of sea-level rise and low probability flooding events on coastal communities.

PubMed

Prime, Thomas; Brown, Jennifer M; Plater, Andrew J

2015-01-01

Conventionally flood mapping typically includes only a static water level (e.g. peak of a storm tide) in coastal flood inundation events. Additional factors become increasingly important when increased water-level thresholds are met during the combination of a storm tide and increased mean sea level. This research incorporates factors such as wave overtopping and river flow in a range of flood inundation scenarios of future sea-level projections for a UK case study of Fleetwood, northwest England. With increasing mean sea level it is shown that wave overtopping and river forcing have an important bearing on the cost of coastal flood events. The method presented converts inundation maps into monetary cost. This research demonstrates that under scenarios of joint extreme surge-wave-river events the cost of flooding can be increased by up to a factor of 8 compared with an increase in extent of up to a factor of 3 relative to "surge alone" event. This is due to different areas being exposed to different flood hazards and areas with common hazard where flood waters combine non-linearly. This shows that relying simply on flood extent and volume can under-predict the actual economic impact felt by a coastal community. Additionally, the scenario inundation depths have been presented as "brick course" maps, which represent a new way of interpreting flood maps. This is primarily aimed at stakeholders to increase levels of engagement within the coastal community.

The SAFRR Tsunami Scenario: Improving Resilience for California from a Plausible M9 Earthquake near the Alaska Peninsula

NASA Astrophysics Data System (ADS)

Ross, S.; Jones, L.; Wilson, R. I.; Bahng, B.; Barberopoulou, A.; Borrero, J. C.; Brosnan, D.; Bwarie, J.; Geist, E. L.; Johnson, L.; Kirby, S. H.; Knight, W.; Long, K.; Lynett, P. J.; Miller, K.; Mortensen, C. E.; Nicolsky, D.; Oglesby, D. D.; Perry, S. C.; Plumlee, G. S.; Porter, K. A.; Real, C. R.; Ryan, K. J.; Suleimani, E.; Thio, H. K.; Titov, V.; Wein, A. M.; Whitmore, P.; Wood, N. J.

2013-12-01

The SAFRR Tsunami Scenario models a hypothetical but plausible tsunami, created by an Mw9.1 earthquake occurring offshore from the Alaskan peninsula, and its impacts on the California coast. We present the likely inundation areas, current velocities in key ports and harbors, physical damage and repair costs, economic consequences, environmental impacts, social vulnerability, emergency management, and policy implications for California associated with the tsunami scenario. The intended users are those who must make mitigation decisions before and rapid decisions during future tsunamis. Around a half million people would be present in the scenario's inundation area in residences, businesses, public venues, parks and beaches. Evacuation would likely be ordered for the State of California's maximum mapped tsunami inundation zone, evacuating an additional quarter million people from residences and businesses. Some island and peninsula communities would face particular evacuation challenges because of limited access options and short warning time, caused by the distance between Alaska and California. Evacuations may also be a challenge for certain dependent-care populations. One third of the boats in California's marinas could be damaged or sunk, costing at least 700 million in repairs to boats and docks, and potentially much more to address serious issues due to sediment transport and environmental contamination. Fires would likely start at many sites where fuel and petrochemicals are stored in ports and marinas. Tsunami surges and bores may travel several miles inland up coastal rivers. Debris clean-up and recovery of inundated and damaged areas will take days, months, or years depending on the severity of impacts and the available resources for recovery. The Ports of Los Angeles and Long Beach (POLA/LB) would be shut down for a miniμm of two days due to strong currents. Inundation of dry land in the ports would result in 100 million damages to cargo and additional downtime. The direct exposure of port trade value totals over 1.2 billion, while associated business interruption losses in the California economy could more than triple that value. Other estimated damages include 1.8 billion of property damage and 85 million for highway and railroad repairs. In total, we have estimated repair and replacement costs of almost 3 billion to California marinas, coastal properties and the POLA/LB. These damages could cause $6 billion of business interruption losses in the California economy, but that could be reduced by 80-90% with the implementation of business continuity or resilience strategies. This scenario provides the basis for improving preparedness, mitigation, and continuity planning for tsunamis, which can reduce damage and economic impacts and enhance recovery efforts. Two positive outcomes have already resulted from the SAFRR Tsunami Scenario. Emergency managers in areas where the scenario inundation exceeds the State's maximum inundation zone have been notified and evacuation plans have been updated appropriately. The State has also worked with NOAA's West Coast and Alaska Tsunami Warning Center to modify future message protocols to facilitate effective evacuations in California. While our specific results pertain to California, the lessons learned and our scenario approach can be applied to other regions.

Crowdsourced data for flood hydrology: Feedback from recent citizen science projects in Argentina, France and New Zealand

NASA Astrophysics Data System (ADS)

Le Coz, Jérôme; Patalano, Antoine; Collins, Daniel; Guillén, Nicolás Federico; García, Carlos Marcelo; Smart, Graeme M.; Bind, Jochen; Chiaverini, Antoine; Le Boursicaud, Raphaël; Dramais, Guillaume; Braud, Isabelle

2016-10-01

New communication and digital image technologies have enabled the public to produce large quantities of flood observations and share them through social media. In addition to flood incident reports, valuable hydraulic data such as the extent and depths of inundated areas and flow rate estimates can be computed using messages, photos and videos produced by citizens. Such crowdsourced data help improve the understanding and modelling of flood hazard. Since little feedback on similar initiatives is available, we introduce three recent citizen science projects which have been launched independently by research organisations to quantitatively document flood flows in catchments and urban areas of Argentina, France, and New Zealand. Key drivers for success appear to be: a clear and simple procedure, suitable tools for data collecting and processing, an efficient communication plan, the support of local stakeholders, and the public awareness of natural hazards.

Flooding in the middle Koyukuk River basin, Alaska, August 1994

USGS Publications Warehouse

Meyer, David F.

1995-01-01

During August 1994, a flood on the Koyukuk River, Alaska, inundated the villages of Allakaket and Alatna and parts of Hughes. Topographic maps of the inundated areas, showing peak water-surface elevations and depths of water, indicate that flooding ranged from 2 to more than 10 feet deep in Allakaket, from 8 to more than 10 feet deep in Alatna, and from 0 to more than 10 feet deep in Hughes. Severe damage to buildings occurred in Allakaket and Alatna; minor damage occurred in Hughes, although some homes were irreparably damaged by inundation. Between the mouth of the Kanuti River, about 10 miles downstream from Allakaket, to Hughes, the peak discharge was about 330,000 cubic feet per second. A flow of that magnitude at Hughes has an annual probability of occurrence of 1 percent.

Geovisualization in the HydroProg web map service

NASA Astrophysics Data System (ADS)

Spallek, Waldemar; Wieczorek, Malgorzata; Szymanowski, Mariusz; Niedzielski, Tomasz; Swierczynska, Malgorzata

2016-04-01

The HydroProg system, built at the University of Wroclaw (Poland) in frame of the research project no. 2011/01/D/ST10/04171 financed by the National Science Centre of Poland, has been designed for computing predictions of river stages in real time on a basis of multimodelling. This experimental system works on the upper Nysa Klodzka basin (SW Poland) above the gauge in the town of Bardo, with the catchment area of 1744 square kilometres. The system operates in association with the Local System for Flood Monitoring of Klodzko County (LSOP), and produces hydrograph prognoses as well as inundation predictions. For presenting the up-to-date predictions and their statistics in the online mode, the dedicated real-time web map service has been designed. Geovisualisation in the HydroProg map service concerns: interactive maps of study area, interactive spaghetti hydrograms of water level forecasts along with observed river stages, animated images of inundation. The LSOP network offers a high spatial and temporal resolution of observations, as the length of the sampling interval is equal to 15 minutes. The main environmental elements related to hydrological modelling are shown on the main map. This includes elevation data (hillshading and hypsometric tints), rivers and reservoirs as well as catchment boundaries. Furthermore, we added main towns, roads as well as political and administrative boundaries for better map understanding. The web map was designed as a multi-scale representation, with levels of detail and zooming according to scales: 1:100 000, 1:250 000 and 1:500 000. Observations of water level in LSOP are shown on interactive hydrographs for each gauge. Additionally, predictions and some of their statistical characteristics (like prediction errors and Nash-Sutcliffe efficiency) are shown for selected gauges. Finally, predictions of inundation are presented on animated maps which have been added for four experimental sites. The HydroProg system is a strictly scientific project, but the web map service has been designed for all web users. The main objective of the paper is to present the design process of the web map service, following the cartographic and graphic principles.

Potential effects of four Flaming Gorge Dam hydropower operational scenarios on the fishes of the Green River, Utah and Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hlohowskyj, I.; Hayse, J.W.

1995-09-01

Aerial videography and modeling were used to evaluate the impacts of four hydropower operational scenarios at Flaming Gorge Dam, Utah, on trout and native fishes in the Green River, Utah and Colorado. The four operational scenarios studied were year-round high fluctuations, seasonally adjusted high fluctuations, seasonally adjusted moderate fluctuations, and seasonally adjusted steady flows. Impacts on trout were evaluated by examining differences among scenarios in the areas of inundated substrates that serve as spawning and feeding habitat. All scenarios would provide at least 23 acres per mile of habitat for spawning and food production; seasonally adjusted operations would provide additionalmore » areas during periods of sustained high release. Seasonally adjusted high fluctuations would increase inundated areas by 12 to 26% for a short period in winter and spring, but food production and reproduction would not be expected to increase. Seasonally adjusted moderate fluctuations and steady flows would produce similar increases in area, but the longer period of inundation could also result in increased food production and provide additional spawning sites for trout. Impacts on native fishes were assessed by examining daily changes in backwater nursery areas. Compared with year-round high fluctuations, the daily changes in backwater area would decrease by about 47, 89, and 100% under the seasonally adjusted high fluctuation, moderate fluctuation, and steady flow scenarios, respectively. Similarly, daily stage fluctuations during the nursery period would decrease by 72, 89, and 100% under the seasonally adjusted high fluctuation, moderate fluctuation, and steady flow scenarios, respectively. These reductions in daily fluctuations in backwater area and stage would improve conditions in nursery habitats and could in turn improve recruitment and overwinter survival. Introduced fish species could also benefit from the seasonally adjusted operational scenarios.« less

Impact of hydrogeological factors on groundwater salinization due to ocean-surge inundation

NASA Astrophysics Data System (ADS)

Yang, Jie; Zhang, Huichen; Yu, Xuan; Graf, Thomas; Michael, Holly A.

2018-01-01

Ocean surges cause seawater inundation of coastal inland areas. Subsequently, seawater infiltrates into coastal aquifers and threatens the fresh groundwater resource. The severity of resulting salinization can be affected by hydrogeological factors including aquifer properties and hydrologic conditions, however, little research has been done to assess these effects. To understand the impacts of hydrogeological factors on groundwater salinization, we numerically simulated an ocean-surge inundation event on a two-dimensional conceptual coastal aquifer using a coupled surface-subsurface approach. We varied model permeability (including anisotropy), inland hydraulic gradient, and recharge rate. Three salinization-assessment indicators were developed, based on flushing time, depth of salt penetration, and a combination of the two, weighted flushing time, with which the impact of hydrogeological factors on groundwater vulnerability to salinization were quantitatively assessed. The vulnerability of coastal aquifers increases with increasing isotropic permeability. Low horizontal permeability (kx) and high vertical permeability (kz) lead to high aquifer vulnerability, and high kx and low kz lead to low aquifer vulnerability. Vulnerability decreases with increasing groundwater hydraulic gradient and increasing recharge rate. Additionally, coastal aquifers with a low recharge rate (R ≤ 300 mm yr-1) may be highly vulnerable to ocean-surge inundation. This study shows how the newly introduced indicators can be used to quantitatively assess coastal aquifer vulnerability. The results are important for global vulnerability assessment of coastal aquifers to ocean-surge inundation.

The simulation of Typhoon-induced coastal inundation in Busan, South Korea applying the downscaling technique

NASA Astrophysics Data System (ADS)

Jang, Dongmin; Park, Junghyun; Yuk, Jin-Hee; Joh, MinSu

2017-04-01

Due to typhoons, the south coastal cities including Busan in South Korea coastal are very vulnerable to a surge, wave and corresponding coastal inundation, and are affected every year. In 2016, South Korea suffered tremendous damage by typhoon 'Chaba', which was developed near east-north of Guam on Sep. 28 and had maximum 10-minute sustained wind speed of about 50 m/s, 1-minute sustained wind speed of 75 m/s and a minimum central pressure of 905 hpa. As 'Chaba', which is the strongest since typhoon 'Maemi' in 2003, hit South Korea on Oct. 5, it caused a massive economic and casualty damage to Ulsan, Gyeongju and Busan in South Korea. In particular, the damage of typhoon-induced coastal inundation in Busan, where many high-rise buildings and residential areas are concentrated near coast, was serious. The coastal inundation could be more affected by strong wind-induced wave than surge. In fact, it was observed that the surge height was about 1 m averagely and a significant wave height was about 8 m at coastal sea nearby Busan on Oct. 5 due to 'Chaba'. Even though the typhoon-induced surge elevated the sea level, the typhoon-induced long period wave with wave period of more than 15s could play more important role in the inundation. The present work simulated the coastal inundation induced by 'Chaba' in Busan, South Korea considering the effects of typhoon-induced surge and wave. For 'Chaba' hindcast, high resolution Weather Research and Forecasting model (WRF) was applied using a reanalysis data produced by NCEP (FNL 0.25 degree) on the boundary and initial conditions, and was validated by the observation of wind speed, direction and pressure. The typhoon-induced coastal inundation was simulated by an unstructured gird model, Finite Volume Community Ocean Model (FVCOM), which is fully current-wave coupled model. To simulate the wave-induced inundation, 1-way downscaling technique of multi domain was applied. Firstly, a mother's domain including Korean peninsula was simulated using wind and pressure produced by WRF to produce surge and wave. And then, the wave-induced inundation was simulated applying the surge height and wave height simulated by mother's model to the open boundary and initial condition of child's model which was ranged near Busan. Our simulated surge height is generally underestimated about 15 % due to the underestimation of surface pressure on WRF. However, since the effect of wave on inundation could be more significant than surge-induced forcing in this real system, our research could predict the typhoon-induced inundation by combining the surge and wave forcing in nested domain.

Sensitivity of Tsunami Waves and Coastal Inundation/Runup to Seabed Displacement Models: Application to the Cascadia Subduction zone

NASA Astrophysics Data System (ADS)

Jalali Farahani, R.; Fitzenz, D. D.; Nyst, M.

2015-12-01

Major components of tsunami hazard modeling include earthquake source characterization, seabed displacement, wave propagation, and coastal inundation/run-up. Accurate modeling of these components is essential to identify the disaster risk exposures effectively, which would be crucial for insurance industry as well as policy makers to have tsunami resistant design of structures and evacuation planning (FEMA, 2008). In this study, the sensitivity and variability of tsunami coastal inundation due to Cascadia megathrust subduction earthquake are studied by considering the different approaches for seabed displacement model. The first approach is the analytical expressions that were proposed by Okada (1985, 1992) for the surface displacements and strains of rectangular sources. The second approach was introduced by Meade (2006) who introduced analytical solutions for calculating displacements, strains, and stresses on triangular sources. In this study, the seabed displacement using triangular representation of geometrically complex fault surfaces is compared with the Okada rectangular representations for the Cascadia subduction zone. In the triangular dislocation algorithm, the displacement is calculated using superposition of two angular dislocations for each of the three triangle legs. The triangular elements could give a better and gap-free representation of the fault surfaces. In addition, the rectangular representation gives large unphysical vertical displacement along the shallow-depth fault edge that generates unrealistic short-wavelength waves. To study the impact of these two different algorithms on the final tsunami inundation, the initial tsunami wave as well as wave propagation and the coastal inundation are simulated. To model the propagation of tsunami waves and coastal inundation, 2D shallow water equations are modeled using the seabed displacement as the initial condition for the numerical model. Tsunami numerical simulation has been performed on high-resolution bathymetric/topographic computational grids to identify accurate tsunami impact and flooding limits for the west of USA.

75 FR 4057 - Exelon Generation Company, LLC; PPL Holtwood, LLC; Notice of Application for Amendment of License...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-26

... no project purpose and adding a shoreline buffer strip and a small area inundated by Conowingo Pond... Projects' Boundaries: (1) Exelon and PPL propose removing areas within their projects' boundaries that...

Flood elevations for the Soleduck River at Sol Duc Hot Springs, Clallam County, Washington

USGS Publications Warehouse

Nelson, L.M.

1983-01-01

Elevations and inundation areas of a 100-year flood of the Soleduck River, Washington, were determined by the U.S. Geological Survey for the area in the vicinity of the Sol Duc Hot Springs resort, a public facility in the Olympic National Park that under Federal law must be located beyond or protected from damage by a 100-year flood. Results show that most flooding could be eliminated by raising parts of an existing dike. In general, little flood damage is expected, except at the southern end of an undeveloped airstrip that could become inundated and hazardous due to flow from a tributary. The airstrip is above the 100-year flood of the Soleduck River.

Tsunami hazard assessment in the Hudson River Estuary based on dynamic tsunami-tide simulations

NASA Astrophysics Data System (ADS)

Shelby, Michael; Grilli, Stéphan T.; Grilli, Annette R.

2016-12-01

This work is part of a tsunami inundation mapping activity carried out along the US East Coast since 2010, under the auspice of the National Tsunami Hazard Mitigation program (NTHMP). The US East Coast features two main estuaries with significant tidal forcing, which are bordered by numerous critical facilities (power plants, major harbors,...) as well as densely built low-level areas: Chesapeake Bay and the Hudson River Estuary (HRE). HRE is the object of this work, with specific focus on assessing tsunami hazard in Manhattan, the Hudson and East River areas. In the NTHMP work, inundation maps are computed as envelopes of maximum surface elevation along the coast and inland, by simulating the impact of selected probable maximum tsunamis (PMT) in the Atlantic ocean margin and basin. At present, such simulations assume a static reference level near shore equal to the local mean high water (MHW) level. Here, instead we simulate maximum inundation in the HRE resulting from dynamic interactions between the incident PMTs and a tide, which is calibrated to achieve MHW at its maximum level. To identify conditions leading to maximum tsunami inundation, each PMT is simulated for four different phases of the tide and results are compared to those obtained for a static reference level. We first separately simulate the tide and the three PMTs that were found to be most significant for the HRE. These are caused by: (1) a flank collapse of the Cumbre Vieja Volcano (CVV) in the Canary Islands (with a 80 km3 volume representing the most likely extreme scenario); (2) an M9 coseismic source in the Puerto Rico Trench (PRT); and (3) a large submarine mass failure (SMF) in the Hudson River canyon of parameters similar to the 165 km3 historical Currituck slide, which is used as a local proxy for the maximum possible SMF. Simulations are performed with the nonlinear and dispersive long wave model FUNWAVE-TVD, in a series of nested grids of increasing resolution towards the coast, by one-way coupling. Four levels of nested grids are used, from a 1 arc-min spherical coordinate grid in the deep ocean down to a 39-m Cartesian grid in the HRE. Bottom friction coefficients in the finer grids are calibrated for the tide to achieve the local spatially averaged MHW level at high tide in the HRE. Combined tsunami-tide simulations are then performed for four phases of the tide corresponding to each tsunami arriving at Sandy Hook (NJ): 1.5 h ahead, concurrent with, 1.5 h after, and 3 h after the local high tide. These simulations are forced along the offshore boundary of the third-level grid by linearly superposing time series of surface elevation and horizontal currents of the calibrated tide and each tsunami wave train; this is done in deep enough water for a linear superposition to be accurate. Combined tsunami-tide simulations are then performed with FUNWAVE-TVD in this and the finest nested grids. Results show that, for the 3 PMTs, depending on the tide phase, the dynamic simulations lead to no or to a slightly increased inundation in the HRE (by up to 0.15 m depending on location), and to larger currents than for the simulations over a static level; the CRT SMF proxy tsunami is the PMT leading to maximum inundation in the HRE. For all tide phases, nonlinear interactions between tide and tsunami currents modify the elevation, current, and celerity of tsunami wave trains, mostly in the shallower water areas of the HRE where bottom friction dominates, as compared to a linear superposition of wave elevations and currents. We note that, while dynamic simulations predict a slight increase in inundation, this increase may be on the same order as, or even less than sources of uncertainty in the modeling of tsunami sources, such as their initial water elevation, and in bottom friction and bathymetry used in tsunami grids. Nevertheless, results in this paper provide insight into the magnitude and spatial variability of tsunami propagation and impact in the complex inland waterways surrounding New York City, and of their modification by dynamic tidal effects. We conclude that changes in inundation resulting from the inclusion of a dynamic tide in the specific case of the HRE, although of scientific interest, are not significant for tsunami hazard assessment and that the standard approach of specifying a static reference level equal to MHW is conservative. However, in other estuaries with similarly complex bathymetry/topography and stronger tidal currents, a simplified static approach might not be appropriate.

Simulating a 40-year flood event climatology of Australia with a view to ocean-land teleconnections

NASA Astrophysics Data System (ADS)

Schumann, Guy J.-P.; Andreadis, Konstantinos; Stampoulis, Dimitrios; Bates, Paul

2015-04-01

We develop, for the first time, a proof-of-concept version for a high-resolution global flood inundation model to generate a flood inundation climatology of the past 40 years (1973-2012) for the entire Australian continent at a native 1 km resolution. The objectives of our study includes (1) deriving an inundation climatology for a continent (Australia) as a demonstrator case to understand the requirements for expanding globally; (2) developing a test bed to assess the potential and value of current and future satellite missions (GRACE, SMAP, ICESat-2, AMSR-2, Sentinels and SWOT) in flood monitoring; and (3) answering science questions such as the linking of inundation to ocean circulation teleconnections. We employ the LISFLOOD-FP hydrodynamic model to generate a flood inundation climatology. The model will be built from freely available SRTM-derived data (channel widths, bank heights and floodplain topography corrected for vegetation canopy using ICESat canopy heights). Lakes and reservoirs are represented and channel hydraulics are resolved using actual channel data with bathymetry inferred from hydraulic geometry. Simulations are run with gauged flows and floodplain inundation climatology are compared to observations from GRACE, flood maps from Landsat, SAR, and MODIS. Simulations have been completed for the entire Australian continent. Additionally, changes in flood inundation have been correlated with indices related to global ocean circulation, such as the El Niño Southern Oscillation index. We will produce data layers on flood event climatology and other derived (default) products from the proposed model including channel and floodplain depths, flow direction, velocity vectors, floodplain water volume, shoreline extent and flooded area. These data layers will be in the form of simple vector and raster formats. Since outputs will be large in size we propose to upload them onto Google Earth under the GEE API license.

Satellite microwave detection of contrasting changes in surface inundation across pan-Arctic permafrost zones

NASA Astrophysics Data System (ADS)

Watts, J.; Kimball, J. S.; Jones, L. A.; Schroeder, R.; McDonald, K. C.

2012-12-01

Surface water inundation in the Arctic is concomitant with soil permafrost and strongly influences land-atmosphere water, energy and carbon (CO2, CH4) exchange, and plant community structure. We examine recent (2003-2010) surface water inundation patterns across the pan-Arctic (≥ 50 deg.N) and within major permafrost zones using satellite passive microwave remote sensing retrievals of fractional open water extent (Fw) derived from Advanced Microwave Scanning Radiometer for EOS (AMSR-E) 18.7 and 23.8 GHz brightness temperatures. The AMSR-E Fw retrievals are insensitive to atmosphere contamination and solar illumination effects, enabling daily Fw monitoring across the Arctic. The Fw retrievals are sensitive to sub-grid scale open water inundation area, including lakes and wetlands, within the relatively coarse (~25-km resolution) satellite footprint. A forward model error sensitivity analysis indicates that total Fw retrieval uncertainty is within ±4.1% (RMSE), and AMSR-E Fw compares favorably (0.71 < R2 < 0.84) with alternative static open water maps derived from finer scale (30-m to 250-m resolution) Landsat, MODIS and SRTM radar-based products. The Fw retrievals also show dynamic seasonal and annual variability in surface inundation that corresponds (0.71 < R < 0.87) with regional wet/dry cycles inferred from basin discharge records, including Yukon, Mackenzie, Ob, Yenisei, and Lena basins. A regional change analysis of the 8-yr AMSR-E record shows no significant trend in pan-Arctic wide Fw, and instead reveals contrasting inundation changes within permafrost zones. Widespread Fw wetting is observed within continuous (92% of grid cells with significant trend show wetting; p < 0.1) and discontinuous (82%) permafrost zones, while areas with sporadic/isolated permafrost show widespread (71%) Fw drying. These results are consistent with previous studies showing evidence of changes in regional surface hydrology influenced by permafrost degradation under recent climate warming. Changes in Fw may also be linked to shifts in regional precipitation patterns and a lengthening non-frozen season. Regional changes observed in the AMSR-E Fw record compliment finer-scale permafrost monitoring efforts and documented variability in surface inundation extent may help constrain pan-Arctic lake and wetland CO2, CH4 emission estimates. This work was supported under the Jet Propulsion Laboratory, California Institute of Technology under contract to the National Aeronautics and Space Administration, NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) programs.

Characterization of peak streamflows and flood inundation of selected areas in Louisiana from the August 2016 flood

USGS Publications Warehouse

Watson, Kara M.; Storm, John B.; Breaker, Brian K.; Rose, Claire E.

2017-02-06

Heavy rainfall occurred across Louisiana and southwestern Mississippi in August 2016 as a result of a slow-moving area of low pressure and a high amount of atmospheric moisture. The storm caused major flooding in the southern portions of Louisiana including areas surrounding Baton Rouge and Lafayette. Flooding occurred along the rivers such as the Amite, Comite, Tangipahoa, Tickfaw, Vermilion, and Mermentau Rivers. Over 31 inches of rain was reported in the city of Watson, 20 miles northeast of Baton Rouge, La., over the duration of the event. Streamflow-gaging stations operated by the U.S. Geological Survey (USGS) recorded peak streamflows of record at 10 locations, and 7 other locations experienced peak streamflows ranking in the top five for the duration of the period of record. In August 2016, USGS hydrographers made 50 discharge measurements at 21 locations on streams in Louisiana. Many of those discharge measurements were made for the purpose of verifying the accuracy of stage-streamflow relations at gaging stations operated by the USGS. Following the storm event, USGS hydrographers recovered and documented 590 high-water marks, noting location and height of the water above land surface. Many of these high-water marks were used to create 12 flood-inundation maps for selected communities of Louisiana that experienced flooding in August 2016. Digital datasets of the inundation area, modeling boundary, water depth rasters, and final map products are available online.

Implications of sea level rise scenarios on land use /land cover classes of the coastal zones of Cochin, India.

PubMed

Mani Murali, R; Dinesh Kumar, P K

2015-01-15

Physical responses of the coastal zones in the vicinity of Cochin, India due to sea level rise are investigated based on analysis of inundation scenarios. Quantification of potential habitat loss was made by merging the Land use/Land cover (LU/LC) prepared from the satellite imagery with the digital elevation model. Scenarios were generated for two different rates of sea level rise and responses of changes occurred were made to ascertain the vulnerability and loss in extent. LU/LC classes overlaid on 1 m and 2 m elevation showed that it was mostly covered by vegetation areas followed by water and urban zones. For the sea level rise scenarios of 1 m and 2 m, the total inundation zones were estimated to be 169.11 km(2) and 598.83 km(2) respectively using Geographic Information System (GIS). The losses of urban areas were estimated at 43 km(2) and 187 km(2) for the 1 m and 2 m sea level rise respectively which is alarming information for the most densely populated state of India. Quantitative comparison of other LU/LC classes showed significant changes under each of the inundation scenarios. The results obtained conclusively point that sea level rise scenarios will bring profound effects on the land use and land cover classes as well as on coastal landforms in the study region. Coastal inundation would leave ocean front and inland properties vulnerable. Increase in these water levels would alter the coastal drainage gradients. Reduction in these gradients would increase flooding attributable to rainstorms which could promote salt water intrusion into coastal aquifers and force water tables to rise. Changes in the coastal landforms associated with inundation generate concern in the background that the coastal region may continue to remain vulnerable in the coming decades due to population growth and development pressures. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development and Validation of Remote Sensing-Based Surface Inundation Products for Vector-Borne Disease Risk in East Africa

NASA Astrophysics Data System (ADS)

Jensen, K.; McDonald, K. C.; Ceccato, P.; Schroeder, R.; Podest, E.

2014-12-01

The potential impact of climate variability and change on the spread of infectious disease is of increasingly critical concern to public health. Newly-available remote sensing datasets may be combined with predictive modeling to develop new capabilities to mitigate risks of vector-borne diseases such as malaria, leishmaniasis, and rift valley fever. We have developed improved remote sensing-based products for monitoring water bodies and inundation dynamics that have potential utility for improving risk forecasts of vector-borne disease epidemics. These products include daily and seasonal surface inundation based on the global mappings of inundated area fraction derived at the 25-km scale from active and passive microwave instruments ERS, QuikSCAT, ASCAT, and SSM/I data - the Satellite Water Microwave Product Series (SWAMPS). Focusing on the East African region, we present validation of this product using multi-temporal classification of inundated areas in this region derived from high resolution PALSAR (100m) and Landsat (30m) observations. We assess historical occurrence of malaria in the east African country of Eritrea with respect to the time series SWAMPS datasets, and we aim to construct a framework for use of these new datasets to improve prediction of future malaria risk in this region. This work is supported through funding from the NASA Applied Sciences Program, the NASA Terrestrial Ecology Program, and the NASA Making Earth System Data Records for Use in Research Environments (MEaSUREs) Program. This study is also supported and monitored by National Oceanic and Atmospheric Administration (NOAA) under Grant - CREST Grant # NA11SEC4810004. The statements contained within the manuscript/research article are not the opinions of the funding agency or the U.S. government, but reflect the authors' opinions. This work was conducted in part under the framework of the ALOS Kyoto and Carbon Initiative. ALOS PALSAR data were provided by JAXA EORC.

A multi-scale ensemble-based framework for forecasting compound coastal-riverine flooding: The Hackensack-Passaic watershed and Newark Bay

NASA Astrophysics Data System (ADS)

Saleh, F.; Ramaswamy, V.; Wang, Y.; Georgas, N.; Blumberg, A.; Pullen, J.

2017-12-01

Estuarine regions can experience compound impacts from coastal storm surge and riverine flooding. The challenges in forecasting flooding in such areas are multi-faceted due to uncertainties associated with meteorological drivers and interactions between hydrological and coastal processes. The objective of this work is to evaluate how uncertainties from meteorological predictions propagate through an ensemble-based flood prediction framework and translate into uncertainties in simulated inundation extents. A multi-scale framework, consisting of hydrologic, coastal and hydrodynamic models, was used to simulate two extreme flood events at the confluence of the Passaic and Hackensack rivers and Newark Bay. The events were Hurricane Irene (2011), a combination of inland flooding and coastal storm surge, and Hurricane Sandy (2012) where coastal storm surge was the dominant component. The hydrodynamic component of the framework was first forced with measured streamflow and ocean water level data to establish baseline inundation extents with the best available forcing data. The coastal and hydrologic models were then forced with meteorological predictions from 21 ensemble members of the Global Ensemble Forecast System (GEFS) to retrospectively represent potential future conditions up to 96 hours prior to the events. Inundation extents produced by the hydrodynamic model, forced with the 95th percentile of the ensemble-based coastal and hydrologic boundary conditions, were in good agreement with baseline conditions for both events. The USGS reanalysis of Hurricane Sandy inundation extents was encapsulated between the 50th and 95th percentile of the forecasted inundation extents, and that of Hurricane Irene was similar but with caveats associated with data availability and reliability. This work highlights the importance of accounting for meteorological uncertainty to represent a range of possible future inundation extents at high resolution (∼m).

Flood-inundation maps for the Suncook River in Epsom, Pembroke, Allenstown, and Chichester, New Hampshire

USGS Publications Warehouse

Flynn, Robert H.; Johnston, Craig M.; Hays, Laura

2012-01-01

Digital flood-inundation maps for a 16.5-mile reach of the Suncook River in Epsom, Pembroke, Allenstown, and Chichester, N.H., from the confluence with the Merrimack River to U.S. Geological Survey (USGS) Suncook River streamgage 01089500 at Depot Road in North Chichester, N.H., were created by the USGS in cooperation with the New Hampshire Department of Homeland Security and Emergency Management. The inundation maps presented in this report depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Suncook River at North Chichester, N.H. (station 01089500). The current conditions at the USGS streamgage may be obtained on the Internet (http://waterdata.usgs.gov/nh/nwis/uv/?site_no=01089500&PARAmeter_cd=00065,00060). The National Weather Service forecasts flood hydrographs at many places that are often collocated with USGS streamgages. Forecasted peak-stage information is available on the Internet at the National Weather Service (NWS) Advanced Hydrologic Prediction Service (AHPS) flood-warning system site (http://water.weather.gov/ahps/) and may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. These maps along with real-time stream stage data from the USGS Suncook River streamgage (station 01089500) and forecasted stream stage from the NWS will provide emergency management personnel and residents with information that is critical for flood-response activities, such as evacuations, road closures, disaster declarations, and post-flood recovery. The maps, along with current stream-stage data from the USGS Suncook River streamgage and forecasted stream-stage data from the NWS, can be accessed at the USGS Flood Inundation Mapping Science Web site http://water.usgs.gov/osw/flood_inundation/.

Hypermediated Art Criticism

ERIC Educational Resources Information Center

Taylor, Pamela G.; Carpenter, B. Stephen, II

2007-01-01

Technological media catapults our perception into what Marshall McLuhan called "new transforming vision and awareness." As our lives become more and more immersed in such technologies as television, film, and interactive computers, we find ourselves inundated with a heightened sense of mindfulness--an aesthetic experience made possible through…

Process-based model with flood control measures towards more realistic global flood modeling

NASA Astrophysics Data System (ADS)

Tang, Q.; Zhang, X.; Wang, Y.; Mu, M.; Lv, A.; Li, Z.

2017-12-01

In the profoundly human-influenced era, the Anthropocene, increased amount of land was developed in flood plains and many flood control measures were implemented to protect people and infrastructures placed in the flood-prone areas. These human influences (for example, dams and dykes) have altered peak streamflow and flood risk, and are already an integral part of flood. However, most of the process-based flood models have yet to taken into account the human influences. In this study, we used a hydrological model together with an advanced hydrodynamic model to assess flood risk at the Baiyangdian catchment. The Baiyangdian Lake is the largest shallow freshwater lake in North China, and it was used as a flood storage area in the past. A new development hub for the Beijing-Tianjin-Hebei economic triangle, namely the Xiongan new area, was recently established in the flood-prone area around the lake. The shuttle radar topography mission (SRTM) digital elevation model (DEMs) was used to parameterize the hydrodynamic model simulation, and the inundation estimates were compared with published flood maps and observed inundation area during the extreme historical flood events. A simple scheme was carried out to consider the impacts of flood control measures, including the reservoirs in the headwaters and the dykes to be built. By comparing model simulations with and without the influences of flood control measures, we demonstrated the importance of human influences in altering the inundated area and depth under design flood conditions. Based on the SRTM DEM and dam and reservoir data in the Global Reservoir and Dam (GRanD) database, we further discuss the potential to develop a global flood model with human influences.

Mobility of pyroclastic flows and surges at the Soufriere Hills Volcano, Montserrat

USGS Publications Warehouse

Calder, E.S.; Cole, P.D.; Dade, W.B.; Druitt, T.H.; Hoblitt, R.P.; Huppert, H.E.; Ritchie, L.; Sparks, R.S.J.; Young, S.R.

1999-01-01

The Soufriere Hills Volcano on Montserrat has produced avalanche-like pyroclastic flows formed by collapse of the unstable lava dome or explosive activity. Pyroclastic flows associated with dome collapse generate overlying dilute surges which detach from and travel beyond their parent flows. The largest surges partially transform by rapid sedimentation into dense secondary pyroclastic flows that pose significant hazards to distal areas. Different kinds of pyroclastic density currents display contrasting mobilities indicated by ratios of total height of fall H, run-out distance L, area inundated A and volume transported V. Dome-collapse flow mobilities (characterised by either L/H or A/V 2/3) resemble those of terrestrial and extraterrestrial cold-rockfalls (Dade and Huppert, 1998). In contrast, fountain-fed pumice flows and fine-grained, secondary pyroclastic flows travel slower but, for comparable initial volumes and heights, can inundate greater areas.

Sri Lanka field survey after the December 2004 Indian Ocean tsunami

USGS Publications Warehouse

Goff, James; Liu, Philip L-F.; Higman, Bretwood; Morton, Robert; Jaffe, Bruce E.; Fernando, Haindra; Lynett, Patrick; Fritz, Hermann; Synolakis, Costas; Fernando, Starin

2006-01-01

An International Tsunami Survey Team (ITST) consisting of scientists from the United States, New Zealand, and Sri Lanka evaluated the impacts of the 26 December 2004 transoceanic tsunami in Sri Lanka two weeks after the event. Tsunami runup height, inundation distance, morphological changes, and sedimentary characteristics of deposits were recorded and analyzed along the southwest and east coasts of the country. Preliminary results show how local topography and bathymetry controlled the limits of inundation and associated damage to the infrastructure. The largest wave height of 8.71 m was recorded at Nonagama, while the greatest inundation distance of 390 m and runup height of 12.50 m was at Yala. At some sites, human alterations to the landscape increased the damage caused by the tsunami; this was particularly evident in areas of coral poaching and of sand dune removal.

iSPUW: integrated sensing and prediction of urban water for sustainable cities

NASA Astrophysics Data System (ADS)

Noh, S. J.; Nazari, B.; Habibi, H.; Norouzi, A.; Nabatian, M.; Seo, D. J.; Bartos, M. D.; Kerkez, B.; Lakshman, L.; Zink, M.; Lee, J.

2016-12-01

Many cities face tremendous water-related challenges in this Century of the City. Urban areas are particularly susceptible not only to excesses and shortages of water but also to impaired water quality. To addresses these challenges, we synergistically integrate advances in computing and cyber-infrastructure, environmental modeling, geoscience, and information science to develop integrative solutions for urban water challenges. In this presentation, we describe the various efforts that are currently ongoing in the Dallas-Fort Worth Metroplex (DFW) area for iSPUW: real-time high-resolution flash flood forecasting, inundation mapping for large urban areas, crowdsourcing of water observations in urban areas, real-time assimilation of crowdsourced observations for street and river flooding, integrated control of lawn irrigation and rainwater harvesting for water conservation and stormwater management, feature mining with causal discovery for flood prediction, and development of the Arlington Urban Hydroinformatics Testbed. Analyzed is the initial data of sensor network for water level and lawn monitoring, and cellphone applications for crowdsourcing flood reports. New data assimilation approaches to deal with categorical and continuous observations are also evaluated via synthetic experiments.

Pitfall Traps and Mini-Winkler Extractor as Complementary Methods to Sample Soil Coleoptera.

PubMed

Carneiro, A C; Batistella, D A; Battirola, L D; Marques, M I

2016-02-01

We compared abundance, species richness, and capture efficiency with pitfall traps and mini-Winkler extractors to examine their use as complementary methods for sampling soil Coleoptera during dry (2010) and high water seasons (2011) in three areas, including inundated and non-inundated regions, in the Pantanal of Poconé, Mato Grosso, Brazil. We paired treatments with two 10 × 10 m plots in inundated and non-inundated locations that were repeated three times in each location for a total of 18 plots. In each plot, we used nine pitfall traps and collected 2 m(2) of leaf litter and surface soil samples with mini-Winkler extractors. We collected a total of 4260 adult beetles comprising 36 families, 113 genera, and 505 species. Most were caught in pitfalls (69%) and the remainder in the mini-Winkler extractors (31%). Each method provided distinct information about the beetle community: 252 species were captured only in pitfall traps, 147 using only the mini-Winkler extractors, and these methods shared another 106 species. Pitfall and mini-Winkler contribute in different ways for the sampling of the soil beetle community, and so they should be considered complementary for a more thorough assessment of community diversity.

A Tank Bromeliad Favors Spider Presence in a Neotropical Inundated Forest

PubMed Central

Hénaut, Yann; Corbara, Bruno; Pélozuelo, Laurent; Azémar, Frédéric; Céréghino, Régis; Herault, Bruno; Dejean, Alain

2014-01-01

Tank bromeliads are good models for understanding how climate change may affect biotic associations. We studied the relationships between spiders, the epiphytic tank bromeliad, Aechmea bracteata, and its associated ants in an inundated forest in Quintana Roo, Mexico, during a drought period while, exceptionally, this forest was dry and then during the flooding that followed. We compared spider abundance and diversity between ‘Aechmea-areas’ and ‘control-areas’ of the same surface area. We recorded six spider families: the Dipluridae, Ctenidae, Salticidae, Araneidae, Tetragnathidae and Linyphiidae among which the funnel-web tarantula, Ischnothele caudata, the only Dipluridae noted, was the most abundant. During the drought period, the spiders were more numerous in the Aechmea-areas than in the control-areas, but they were not obligatorily associated with the Aechmea. During the subsequent flooding, the spiders were concentrated in the A. bracteata patches, particularly those sheltering an ant colony. Also, a kind of specificity existed between certain spider taxa and ant species, but varied between the drought period and subsequent flooding. We conclude that climatic events modulate the relationship between A. bracteata patches and their associated fauna. Tank bromeliads, previously considered only for their ecological importance in supplying food and water during drought, may also be considered refuges for spiders during flooding. More generally, tank bromeliads have an important role in preserving non-specialized fauna in inundated forests. PMID:25494055

Potential flood hazard assessment by integration of ALOS PALSAR and ASTER GDEM: a case study for the Hoa Chau commune, Hoa Vang district, in central Vietnam

NASA Astrophysics Data System (ADS)

Huong, Do Thi Viet; Nagasawa, Ryota

2014-01-01

The potential flood hazard was assessed for the Hoa Chau commune in central Vietnam in order to identify the high flood hazard zones for the decision makers who will execute future rural planning. A new approach for deriving the potential flood hazard based on integration of inundation and flow direction maps is described. Areas inundated in the historical flood event of 2007 were extracted from Advanced Land Observing Satellite (ALOS) phased array L-band synthetic aperture data radar (PALSAR) images, while flow direction characteristics were derived from the ASTER GDEM to extract the depressed surfaces. Past flood experience and the flow direction were then integrated to analyze and rank the potential flood hazard zones. The land use/cover map extracted from LANDSAT TM and flood depth point records from field surveys were utilized to check the possibility of susceptible inundated areas, extracting data from ALOS PALSAR and ranking the potential flood hazard. The estimation of potential flood hazard areas revealed that 17.43% and 17.36% of Hoa Chau had high and medium potential flood hazards, respectively. The flow direction and ALOS PALSAR data were effectively integrated for determining the potential flood hazard when hydrological and meteorological data were inadequate and remote sensing images taken during flood times were not available or were insufficient.

Assimilation of measurement data in hydrodynamic modeling

NASA Astrophysics Data System (ADS)

Karamuz, Emilia; Romanowicz, Renata J.

2016-04-01

This study focuses on developing methods to combine ground-based data from operational monitoring with data from satellite imaging to obtain a more accurate evaluation of flood inundation extents. The distributed flow model MIKE 11 was used to determine the flooding areas for a flood event with available satellite data. Model conditioning was based on the integrated use of data from remote measurement techniques and traditional data from gauging stations. Such conditioning of the model improves the quality of fit of the model results. The use of high resolution satellite images (from IKONOS, QuickBird e.t.c) and LiDAR Digital Elevation Model (DEM) allows information on water levels to be extended to practically any chosen cross-section of the tested section of the river. This approach allows for a better assessment of inundation extent, particularly in areas with a scarce network of gauging stations. We apply approximate Bayesian analysis to integrate the information on flood extent originating from different sources. The approach described above was applied to the Middle River Vistula reach, from the Zawichost to Warsaw gauging stations. For this part of the river the detailed geometry of the river bed and floodplain data were available. Finally, three selected sub-sections were analyzed with the most suitable satellite images of inundation area. ACKNOWLEDGEMENTS This research was supported by the Institute of Geophysics Polish Academy of Sciences through the Young Scientist Grant no. 3b/IGF PAN/2015.

Dynamic simulation and numerical analysis of hurricane storm surge under sea level rise with geomorphologic changes along the northern Gulf of Mexico

USGS Publications Warehouse

Bilskie, Matthew V.; Hagen, S.C.; Alizad, K.A.; Medeiros, S.C.; Passeri, Davina L.; Needham, H.F.; Cox, A.

2016-01-01

This work outlines a dynamic modeling framework to examine the effects of global climate change, and sea level rise (SLR) in particular, on tropical cyclone-driven storm surge inundation. The methodology, applied across the northern Gulf of Mexico, adapts a present day large-domain, high resolution, tide, wind-wave, and hurricane storm surge model to characterize the potential outlook of the coastal landscape under four SLR scenarios for the year 2100. The modifications include shoreline and barrier island morphology, marsh migration, and land use land cover change. Hydrodynamics of 10 historic hurricanes were simulated through each of the five model configurations (present day and four SLR scenarios). Under SLR, the total inundated land area increased by 87% and developed and agricultural lands by 138% and 189%, respectively. Peak surge increased by as much as 1 m above the applied SLR in some areas, and other regions were subject to a reduction in peak surge, with respect to the applied SLR, indicating a nonlinear response. Analysis of time-series water surface elevation suggests the interaction between SLR and storm surge is nonlinear in time; SLR increased the time of inundation and caused an earlier arrival of the peak surge, which cannot be addressed using a static (“bathtub”) modeling framework. This work supports the paradigm shift to using a dynamic modeling framework to examine the effects of global climate change on coastal inundation. The outcomes have broad implications and ultimately support a better holistic understanding of the coastal system and aid restoration and long-term coastal sustainability.

Flood Inundation Modelling in Data Sparse Deltas

NASA Astrophysics Data System (ADS)

Hawker, Laurence; Bates, Paul; Neal, Jeffrey

2017-04-01

An estimated 7% of global population currently live in deltas, and this number is increasing over time. This has resulted in numerous human induced impacts on deltas ranging from subsidence, upstream sediment trapping and coastal erosion amongst others. These threats have already impacted on flood dynamics in deltas and could intensify in line with human activities. However, the myriad of threats creates a large number of potential scenarios that need to be evaluated. Therefore, to assess the impacts of these scenarios, a pre-requisite is a flood inundation model that is both computationally efficient and flexible in its setup so it can be applied in data-sparse settings. An intermediate scale, which compromises between the computational speed of a global model and the detail of a case specific bespoke model, was chosen to achieve this. To this end, we have developed an intermediate scale flood inundation model at a resolution of 540m of the Mekong Delta, built with freely available data, using the LISFLOOD-FP hydrodynamic model. The purpose of this is to answer the following questions: 1) How much detail is required to accurately simulate flooding in the Mekong Delta? , 2) What characteristics of deltas are most important to include in flood inundation models? Models were run using a vegetation removed SRTM DEM and a hind-casting of tidal heights as a downstream boundary. Results indicate the importance of vegetation removal in the DEM for inundation extent and the sensitivity of water level to roughness coefficients. The propagation of the tidal signal was found to be sensitive to bathymetry, both within the river channel and offshore, yet data availability for this is poor, meaning the modeller has to be careful in his or her choice of bathymetry interpolation Supplementing global river channel data with more localised data demonstrated minor improvements in results suggesting detailed channel information is not always needed to produce good results. It is envisaged that this work will lead to current and future flood risk analysis of not only the Mekong Delta, but also other data sparse deltas owing to the model's utilisation of freely available data that has a global coverage. This will ultimately aid in the much-needed estimation of flood risk in deltaic settings.

Tsunami Impact in Morocco due to Most Credible Tsunami Scenarios in the Gulf of Cadiz.

NASA Astrophysics Data System (ADS)

Omira, R.; Baptista, M. A.; Miranda, J. M.; Toto, E. A.

2009-04-01

In the Gulf of Cadiz, the tsunami risk should be considered major due to the peculiar geological context close to the Nubia-Eurasia plate boundary and also to the high vulnerability of the coastlines in the region. The extensive occupation of coastal areas in the surrounding countries - Portugal, Spain and Morocco, the enormous influxes of tourists during high season and the large economic value of harbors and other coastal facilities increase considerably the vulnerability to tsunami impact. In order to establish the Most Credible Tsunami Scenarios we used the earthquake scenarios in the Gulf of Cadiz area. Each scenario has an associated typical fault/or faults and a set of fault parameters that are used as input to compute the sea bottom deformation using Okada's equations. Tsunami propagation uses COMCOT-LX, modified version of the COMCOT Cornnell University code. Maximum wave height (MWH) and tsunami energy direction are computed, for each tsunamigenic scenario for the north Atlantic coast of Morocco. Finally we selected the harbor of Casablanca for the production of inundation maps for Casablanca This research was funded by NEAREST and TRANSFER, 6FP-European Union.

Direct local building inundation depth determination in 3-D point clouds generated from user-generated flood images

NASA Astrophysics Data System (ADS)

Griesbaum, Luisa; Marx, Sabrina; Höfle, Bernhard

2017-07-01

In recent years, the number of people affected by flooding caused by extreme weather events has increased considerably. In order to provide support in disaster recovery or to develop mitigation plans, accurate flood information is necessary. Particularly pluvial urban floods, characterized by high temporal and spatial variations, are not well documented. This study proposes a new, low-cost approach to determining local flood elevation and inundation depth of buildings based on user-generated flood images. It first applies close-range digital photogrammetry to generate a geo-referenced 3-D point cloud. Second, based on estimated camera orientation parameters, the flood level captured in a single flood image is mapped to the previously derived point cloud. The local flood elevation and the building inundation depth can then be derived automatically from the point cloud. The proposed method is carried out once for each of 66 different flood images showing the same building façade. An overall accuracy of 0.05 m with an uncertainty of ±0.13 m for the derived flood elevation within the area of interest as well as an accuracy of 0.13 m ± 0.10 m for the determined building inundation depth is achieved. Our results demonstrate that the proposed method can provide reliable flood information on a local scale using user-generated flood images as input. The approach can thus allow inundation depth maps to be derived even in complex urban environments with relatively high accuracies.

Forecasting the impact of storm waves and sea-level rise on Midway Atoll and Laysan Island within the Papahānaumokuākea Marine National Monument—a comparison of passive versus dynamic inundation models

USGS Publications Warehouse

Storlazzi, Curt D.; Berkowitz, Paul; Reynolds, Michelle H.; Logan, Joshua B.

2013-01-01

Two inundation events in 2011 underscored the potential for elevated water levels to damage infrastructure and affect terrestrial ecosystems on the low-lying Northwestern Hawaiian Islands in the Papahānaumokuākea Marine National Monument. The goal of this study was to compare passive "bathtub" inundation models based on geographic information systems (GIS) to those that include dynamic water levels caused by wave-induced set-up and run-up for two end-member island morphologies: Midway, a classic atoll with islands on the shallow (2-8 m) atoll rim and a deep, central lagoon; and Laysan, which is characterized by a deep (20-30 m) atoll rim and an island at the center of the atoll. Vulnerability to elevated water levels was assessed using hindcast wind and wave data to drive coupled physics-based numerical wave, current, and water-level models for the atolls. The resulting model data were then used to compute run-up elevations using a parametric run-up equation under both present conditions and future sea-level-rise scenarios. In both geomorphologies, wave heights and wavelengths adjacent to the island shorelines increased more than three times and four times, respectively, with increasing values of sea-level rise, as more deep-water wave energy could propagate over the atoll rim and larger wind-driven waves could develop on the atoll. Although these increases in water depth resulted in decreased set-up along the islands’ shorelines, the larger wave heights and longer wavelengths due to sea-level rise increased the resulting wave-induced run-up. Run-up values were spatially heterogeneous and dependent on the direction of incident wave direction, bathymetry, and island configuration. Island inundation was modeled to increase substantially when wave-driven effects were included, suggesting that inundation and impacts to infrastructure and terrestrial habitats will occur at lower values of predicted sea-level rise, and thus sooner in the 21st century, than suggested by passive GIS-based "bathtub" inundation models. Lastly, observations and the modeling results suggest that classic atolls with islands on a shallow atoll rim are more susceptible to the combined effects of sea-level rise and wave-driven inundation than atolls characterized by a deep atoll rim.

Sea-level rise and coastal groundwater inundation and shoaling at select sites in California, USA

USGS Publications Warehouse

Hoover, Daniel J.; Odigie, Kingsley; Swarzenski, Peter W.; Barnard, Patrick

2017-01-01

Study regionThe study region spans coastal California, USA, and focuses on three primary sites: Arcata, Stinson Beach, and Malibu Lagoon.Study focus1 m and 2 m sea-level rise (SLR) projections were used to assess vulnerability to SLR-driven groundwater emergence and shoaling at select low-lying, coastal sites in California. Separate and combined inundation scenarios for SLR and groundwater emergence were developed using digital elevation models of study site topography and groundwater surfaces constructed from well data or published groundwater level contours.New hydrological insights for the regionSLR impacts are a serious concern in coastal California which has a long (∼1800 km) and populous coastline. Information on the possible importance of SLR-driven groundwater inundation in California is limited. In this study, the potential for SLR-driven groundwater inundation at three sites (Arcata, Stinson Beach, and Malibu Lagoon) was investigated under 1 m and 2 m SLR scenarios. These sites provide insight into the vulnerability of Northern California coastal plains, coastal developments built on beach sand or sand spits, and developed areas around coastal lagoons associated with seasonal streams and berms. Northern California coastal plains with abundant shallow groundwater likely will see significant and widespread groundwater emergence, while impacts along the much drier central and southern California coast may be less severe due to the absence of shallow groundwater in many areas. Vulnerability analysis is hampered by the lack of data on shallow coastal aquifers, which commonly are not studied because they are not suitable for domestic or agricultural use. Shallow saline aquifers may be present in many areas along coastal California, which would dramatically increase vulnerability to SLR-driven groundwater emergence and shoaling. Improved understanding of the extent and response of California coastal aquifers to SLR will help in preparing for mitigation and adaptation.

Hydrologic indicators of hot spots and hot moments of mercury methylation along river corridors

NASA Astrophysics Data System (ADS)

Singer, Michael; Harrison, Lee; Donovan, Patrick; Blum, Joel; Marvin-DiPasquale, Mark

2016-04-01

The biogeochemical cycling of metals and other contaminants river-floodplain corridors is controlled by microbial activity is often affected by dynamic redox conditions. Riverine flooding thus has the potential to affect speciation of redox-sensitive metals such as mercury (Hg). Therefore, flow history over a period of decades potentially holds information on past production of bioavailable Hg. We investigate this process within a Northern California river system that has a legacy of industrial-scale 19th century hydraulic gold mining. In the first known application of this methodology, we combine hydraulic modeling, measurements of Hg species in sediment and biota, and first-order calculations to assess the role of river floodplains in producing monomethylmercury (MMHg), which accumulates in local and migratory biota. We identify areas that represent 'hot spots' (frequently inundated areas of floodplains) and 'hot moments' (floodplain areas inundated for consecutive long periods). We show that the probability of MMHg production in each sector of the river system is dependent on the spatial patterns of overbank flow and drainage, which affect its long-term redox history. MMHg bioaccumulation within the aquatic food web may pose a major risk to humans and waterfowl that eat migratory salmonids, which are being encouraged to come up these rivers to spawn, and there appears to be no end to MMHg production under a regime of increasingly common large floods with extended duration. These findings identify river floodplains as periodic, temporary, yet important, loci of biogeochemical transformation in which contaminants may undergo change during limited periods of the historical hydrologic record. We suggest that inundation is the primary driver of MMHg production in river corridors and that the entire flow history must be analyzed in terms of magnitude and frequency of inundation in order to accurately assess biogeochemical risks, rather than merely highlighting the largest floods.

Effects of anthropogenic land-subsidence on inundation dynamics: the case study of Ravenna, Italy

NASA Astrophysics Data System (ADS)

Carisi, Francesca; Domeneghetti, Alessio; Castellarin, Attilio

2016-05-01

Can differential land-subsidence significantly alter river flooding dynamics, and thus flood risk in flood prone areas? Many studies show how the lowering of the coastal areas is closely related to an increase in the flood-hazard due to more important tidal flooding and see level rise. The literature on the relationship between differential land-subsidence and possible alterations to riverine flood-hazard of inland areas is still sparse, although several geographical areas characterized by significant land-subsidence rates during the last 50 years experienced intensification in both inundation magnitude and frequency. We investigate the possible impact of a significant differential ground lowering on flood hazard over a 77 km2 area around the city of Ravenna, in Italy. The rate of land-subsidence in the study area, naturally in the order of a few mm year-1, dramatically increased up to 110 mm year-1 after World War II, primarily due to groundwater pumping and gas production platforms. The result was a cumulative drop that locally exceeds 1.5 m. Using a recent digital elevation model (res. 5 m) and literature data on land-subsidence, we constructed a ground elevation model over the study area in 1897 and we characterized either the current and the historical DEM with or without road embankments and land-reclamation channels in their current configuration. We then considered these four different topographic models and a two-dimensional hydrodynamic model to simulate and compare the inundation dynamics associated with a levee failure scenario along embankment system of the river Montone, which flows eastward in the southern portion of the study area. For each topographic model, we quantified the flood hazard in terms of maximum water depth (h) and we compared the actual effects on flood-hazard dynamics of differential land-subsidence relative to those associated with other man-made topographic alterations, which resulted to be much more significant.

Geographic information systems supporting the solution of emergencies and their connection to self-actuated notification systems

NASA Astrophysics Data System (ADS)

Reil, Adam; Bureš, Luděk; Roub, Radek; Hejduk, Tomáš; Novák, Pavel

2015-04-01

Geographic information systems represent an important tool in supporting the operation and crisis management of Integrated Rescue System (IRS) branches. The technology of geographic information systems makes it possible to localize specific information directly in the concerned area. A basic pre-requisite for efficient IRS functioning is the identification of so-called critical points in the given territory. The next step is the identification of endangered persons and properties. In these issues, emphasis is put particularly on the time scale, which represents a key aspect of the crisis management. In case of flood danger, the Early Flood Warning Service would inform flood authorities responsible for warning the population, declaring flood activity degrees, IRS activation and organization. For their decision-making, the flood authorities need data on level heights, current discharge rates and inundation areas. The information about discharge rates and height levels can be obtained from the network of recording stream gauge stations operated by the Czech Hydrometeorological Institute. Inundation areas are plotted in the flood control plans of municipalities, which however contain default information about areas flooded at the N-year flood discharges Q5, Q20 and Q100. Because of large intervals, these three scenarios are insufficient for the crisis management of larger communities and towns. Therefore, a data store was suggested that would include maps showing flow rate fields and inundation areas for a finer scale of flood discharges at regular intervals. The scale should be based on the N-year flood discharges with a possibility of extension if required by flood authorities. The discharge interval size should be selected with regard to the dynamics of level height change in the given watercourse. The inundation areas will be then established by way of calculation using the MIKE 21C 2D hydrodynamic model. The novel approach was applied recently in the cadastral area of Lety on the Berounka River. Two sets of certified maps were created: (1) The map of endangered properties 1 - grid of depths, and (2) The map of endangered properties 2 - grid of flow rates. The maps were created from the discharge of 500 m3/s to 1460 m3/s at intervals of 60 m3/s. Two additional discharge values were 1500 m3/s and a calibration discharge of 990 m3/s. In total, thirty-eight maps were created the foundation of which was an orthophotograph map where endangered properties were plotted together with inundation areas. The next step will now be a specific proposal for data store version. The data store will be placed on the web interface where scenarios will be possible to display according to the selected discharge. At the same time, information will be available about the current discharge in the given watercourse. The web interface will be publicly accessible and will be connected to IRS. This study was supported from the Project VG20132015127 as a part of the Security Research conducted by the Ministry of the Interior of the Czech Republic. Keywords: IRS, MIKE 21C, flood

Global cost analysis on adaptation to sea level rise based on RCP/SSP scenarios

NASA Astrophysics Data System (ADS)

Kumano, N.; Tamura, M.; Yotsukuri, M.; Kuwahara, Y.; Yokoki, H.

2017-12-01

Low-lying areas are the most vulnerable to sea level rise (SLR) due to climate change in the future. In order to adapt to SLR, it is necessary to decide whether to retreat from vulnerable areas or to install dykes to protect them from inundation. Therefore, cost- analysis of adaptation using coastal dykes is one of the most essential issues in the context of climate change and its countermeasures. However, few studies have globally evaluated the future costs of adaptation in coastal areas. This study tries to globally analyze the cost of adaptation in coastal areas. First, global distributions of projected inundation impacts induced by SLR including astronomical high tide were assessed. Economic damage was estimated on the basis of the econometric relationship between past hydrological disasters, affected population, and per capita GDP using CRED's EM-DAT database. Second, the cost of adaptation was also determined using the cost database and future scenarios. The authors have built a cost database for installed coastal dykes worldwide and applied it to estimating the future cost of adaptation. The unit costs of dyke construction will increase with socio-economic scenario (SSP) such as per capita GDP. Length of vulnerable coastline is calculated by identifying inundation areas using ETOPO1. Future cost was obtained by multiplying the length of vulnerable coastline and the unit cost of dyke construction. Third, the effectiveness of dyke construction was estimated by comparing cases with and without adaptation.As a result, it was found that incremental adaptation cost is lower than economic damage in the cases of SSP1 and SSP3 under RCP scenario, while the cost of adaptation depends on the durability of the coastal dykes.

Trade-off Assessment of Simplified Routing Models for Short-Term Hydropower Reservoir Optimization

NASA Astrophysics Data System (ADS)

Issao Kuwajima, Julio; Schwanenberg, Dirk; Alvardo Montero, Rodolfo; Mainardi Fan, Fernando; Assis dos Reis, Alberto

2014-05-01

Short-term reservoir optimization, also referred to as model predictive control, integrates model-based forecasts and optimization algorithms to meet multiple management objectives such as water supply, navigation, hydroelectricity generation, environmental obligations and flood protection. It is a valuable decision support tool to handle water-stress conditions or flooding events, and supports decision makers to minimize their impact. If the reservoir management includes downstream control, for example for mitigation flood damages in inundation areas downstream of the operated dam, the flow routing between the dam and the downstream inundation area is of major importance. The unsteady open channel flow in river reaches can be described by the one-dimensional Saint-Venant equations. However, owing to the mathematical complexity of those equations, some simplifications may be required to speed up the computation within the optimization procedure. Another strategy to limit the model runtime is a schematization on a course computational grid. In particular the last measure can introduce significant numerical diffusion into the solution. This is a major drawback, in particular if the reservoir release has steep gradients which we often find in hydropower reservoirs. In this work, four different routing models are assessed concerning their implementation in the predictive control of the Três Marias Reservoir located at the Upper River São Francisco in Brazil: i) a fully dynamic model using the software package SOBEK; ii) a semi-distributed rainfall-runoff model with Muskingum-Cunge routing for the flow reaches of interest, the MGB-IPH (Modelo Hidrológico de Grandes Bacias - Instituto de Pesquisas Hidráulicas); iii) a reservoir routing approach; and iv) a diffusive wave model. The last two models are implemented in the RTC-Tool toolbox. The overall model accuracy between the simplified models in RTC-Tools (iii, iv) and the more sophisticated SOBEK model (i) are comparable, and a lower performance was assessed for the MGB model (ii). Whereas the SOBEK model is able to propagate sharp discharge gradient downstream, the diffusive wave model is damping these gradients significantly due to the course spatial schematization. In the reservoir routing model, which is also schematized on a course grid, we counteract this drawback by modeling parts of the river reach by advection. This results in an excellent ratio between model accuracy / robustness and computational effort making it the approach of choice from the predictive control perspective.

15 CFR 923.31 - Inland boundary.

Code of Federal Regulations, 2010 CFR

2010-01-01

... subject to regular inundation of tidal salt (or Great Lakes) waters which contain marsh flora typical of the region; (5) Beaches—The area affected by wave action directly from the sea. Examples are sandy... appropriate to define the coastal zone as including these watersheds. (2) Areas of tidal influence that extend...

15 CFR 923.31 - Inland boundary.

Code of Federal Regulations, 2014 CFR

2014-01-01

... subject to regular inundation of tidal salt (or Great Lakes) waters which contain marsh flora typical of the region; (5) Beaches—The area affected by wave action directly from the sea. Examples are sandy... appropriate to define the coastal zone as including these watersheds. (2) Areas of tidal influence that extend...

15 CFR 923.31 - Inland boundary.

Code of Federal Regulations, 2013 CFR

2013-01-01

... subject to regular inundation of tidal salt (or Great Lakes) waters which contain marsh flora typical of the region; (5) Beaches—The area affected by wave action directly from the sea. Examples are sandy... appropriate to define the coastal zone as including these watersheds. (2) Areas of tidal influence that extend...

15 CFR 923.31 - Inland boundary.

Code of Federal Regulations, 2012 CFR

2012-01-01

... subject to regular inundation of tidal salt (or Great Lakes) waters which contain marsh flora typical of the region; (5) Beaches—The area affected by wave action directly from the sea. Examples are sandy... appropriate to define the coastal zone as including these watersheds. (2) Areas of tidal influence that extend...

15 CFR 923.31 - Inland boundary.

Code of Federal Regulations, 2011 CFR

2011-01-01

... subject to regular inundation of tidal salt (or Great Lakes) waters which contain marsh flora typical of the region; (5) Beaches—The area affected by wave action directly from the sea. Examples are sandy... appropriate to define the coastal zone as including these watersheds. (2) Areas of tidal influence that extend...

Tsunami impact on SEVESO establishments: the case of Setubal municipality, Portugal.

NASA Astrophysics Data System (ADS)

Fonseca, Nuno; Santos, Ângela; Luís Zêzere, José

2017-04-01

The seismic activity in Portugal mainland is low, being the largest event the one occurred on November 1, 1755, which generated a tsunami with devastating consequences along the seashore nationwide, namely in Lisbon and Setubal. Nowadays, Setubal municipality has seven working SEVESO establishments, five of the upper-tier category and two of the lower-tier. Therefore, it's of a great relevance to model, describe and understand the tsunami locally, to assess its direct and indirect consequences on the SEVESO establishments and its surroundings. Thus, in this study, we considered the 1755 Lisbon Tsunami as the worst-case scenario. The location and portrayal of the SEVESO establishments was attained from previous studies conducted by the authors for the Setubal's municipal government. The relevant information present on the Hazard Map of Mitrena Peninsula and the compulsory information to the public provided by the Seveso establishments operators were also considered. All the sensitive infrastructures potentially affected by the tsunami in each SEVESO establishment were identified, as well as its contents to help to determine the most likely major accident hazard associated. Whenever possible, a buffered zoning was fixed, based on the probable effects and its consequences. An inventory of transport routes, public and recreational sites, and residential areas nearby the affected SEVESO establishments was made, as well as a portrait of the neighboring population based on the latest national Census. Finally, an assessment of the exposed elements was accomplished. The tsunami numerical model results show that the tsunami inundates all the low ground areas, with an average inundation depth of less than 1.5 m at the SEVESO establishments. Furthermore, there are several waves over four hours after the earthquake, being the second one the highest. The numerical model results also show that the tsunami arrives at the first Seveso establishment about 35 minutes after the earthquake. It takes about 50 minutes for it to strike the other SEVESO establishments, located on the most eastern region of Setubal municipality. Only one facility is located on high ground and it's not affected by the tsunami, while five establishments are slightly affected, since only their docks are inundated, with mean inundation depths between 0.60 m and 1.42m. However, there is one SEVESO establishment that raises more concern due to the type of stored and manufactured substances. Its precinct is completely inundated, with a mean inundation depth of 0.81 m. The closest residential area from an affected zone of a SEVESO establishment is about 1500 m away. Moreover, the main road that runs along the shoreline and gives access to most SEVESO establishments located on the eastern region of Setubal is not affected by the tsunami but can be compromised by the major accidents triggered by it. The possible inundation of these establishments by a tsunami can trigger a chain of events with severe consequences, either for the environment as well as for humans. Therefore, a solid commitment is required between public authorities and industrial operators to mitigate whatever outcomes from a scenario like this one.

Flood-inundation maps for Indian Creek and Tomahawk Creek, Johnson County, Kansas, 2014

USGS Publications Warehouse

Peters, Arin J.; Studley, Seth E.

2016-01-25

Digital flood-inundation maps for a 6.4-mile upper reach of Indian Creek from College Boulevard to the confluence with Tomahawk Creek, a 3.9-mile reach of Tomahawk Creek from 127th Street to the confluence with Indian Creek, and a 1.9-mile lower reach of Indian Creek from the confluence with Tomahawk Creek to just beyond the Kansas/Missouri border at State Line Road in Johnson County, Kansas, were created by the U.S. Geological Survey in cooperation with the city of Overland Park, Kansas. The flood-inundation maps, which can be accessed through the U.S. Geological Survey Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the U.S. Geological Survey streamgages on Indian Creek at Overland Park, Kansas; Indian Creek at State Line Road, Leawood, Kansas; and Tomahawk Creek near Overland Park, Kansas. Near real time stages at these streamgages may be obtained on the Web from the U.S. Geological Survey National Water Information System at http://waterdata.usgs.gov/nwis or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at these sites.Flood profiles were computed for the stream reaches by means of a one-dimensional step-backwater model. The model was calibrated for each reach by using the most current stage-discharge relations at the streamgages. The hydraulic models were then used to determine 15 water-surface profiles for Indian Creek at Overland Park, Kansas; 17 water-surface profiles for Indian Creek at State Line Road, Leawood, Kansas; and 14 water-surface profiles for Tomahawk Creek near Overland Park, Kansas, for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from bankfull to the next interval above the 0.2-percent annual exceedance probability flood level (500-year recurrence interval). The simulated water-surface profiles were then combined in a geographic information system with a digital elevation model derived from light detection and ranging data (having a 0.429-foot vertical and 0.228-foot horizontal accuracy) to delineate the area flooded at each water level.The availability of these maps, along with Web information regarding current stage from the U.S. Geological Survey streamgages and forecasted high-flow stages from the National Weather Service, will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations, road closures, and postflood recovery efforts.

Hydrodynamics and inundation of a tidal saltmarsh in Kent County, Delaware

NASA Astrophysics Data System (ADS)

Pieterse, A.; Puleo, J. A.; McKenna, T. E.

2013-12-01

A 2-week field experiment was conducted in March and April 2013 in a tidal wetland in Kent County, Delaware. The study area was a tidal flat fed by a secondary channel of a small tributary of Delaware Bay. The goal of the field study was to investigate spatio-temporal variability in the hydrodynamics of the saltmarsh and tidal flat, over the period of one spring-neap tidal cycle. The experiment combined remotely-sensed imagery with high-frequency in-situ measurements. A tower with imagers (RGB, NIR, TIR) was deployed to quantify the spatial variations of inundation of the channels, flat and marsh. In-situ sensors that measured flow velocity, sediment concentration and water depth were deployed on the tidal flat and in the channels. At three locations, a Nortek Vectrino II - profiling velocimeter was deployed that measured a 30 mm velocity profile at 1 mm vertical increments at 100 Hz. These velocity profiles are used to compute turbulent kinetic energy, energy dissipation and stress profiles close to the bed. Preliminary results of the experiment show that peak velocities occur at the beginning of the rising and end of ebbing tide, when the water levels are low. At these instances, peaks in turbulence and bed stress also occur, which coincides with the largest sediment concentrations that were observed. During both rising and falling tide, flow velocities up to 0.4 m/s were observed in the main channel leading to the tidal flat. After these initial large flow velocities, the flat inundated very quickly, and flow velocities decreased. Furthermore, due to the large flow velocities, bed erosion often took place in the channel at the beginning of each high tide, while deposition occurred during ebbing tide, resulting in small net changes over the tidal cycle. The velocities in the channel relative to those on the adjacent flat were investigated. Furthermore, the relationship between near-bed turbulence and suspended sediment concentration and an analysis of the near-bed turbulence budget will be discussed.

Distribution of uncertainties at the municipality level for flood risk modelling along the river Meuse: implications for policy-making

NASA Astrophysics Data System (ADS)

Pirotton, Michel; Stilmant, Frédéric; Erpicum, Sébastien; Dewals, Benjamin; Archambeau, Pierre

2016-04-01

Flood risk modelling has been conducted for the whole course of the river Meuse in Belgium. Major cities, such as Liege (200,000 inh.) and Namur (110,000 inh.), are located in the floodplains of river Meuse. Particular attention has been paid to uncertainty analysis and its implications for decision-making. The modelling chain contains flood frequency analysis, detailed 2D hydraulic computations, damage modelling and risk calculation. The relative importance of each source of uncertainty to the overall results uncertainty has been estimated by considering several alternate options for each step of the analysis: different distributions were considered in the flood frequency analysis; the influence of modelling assumptions and boundary conditions (e.g., steady vs. unsteady) were taken into account for the hydraulic computation; two different landuse classifications and two sets of damage functions were used; the number of exceedance probabilities involved in the risk calculation (by integration of the risk-curves) was varied. In addition, the sensitivity of the results with respect to increases in flood discharges was assessed. The considered increases are consistent with a "wet" climate change scenario for the time horizons 2021-2050 and 2071-2100 (Detrembleur et al., 2015). The results of hazard computation differ significantly between the upper and lower parts of the course of river Meuse in Belgium. In the former, inundation extents grow gradually as the considered flood discharge is increased (i.e. the exceedance probability is reduced), while in the downstream part, protection structures (mainly concrete walls) prevent inundation for flood discharges corresponding to exceedance probabilities of 0.01 and above (in the present climate). For higher discharges, large inundation extents are obtained in the floodplains. The highest values of risk (mean annual damage) are obtained in the municipalities which undergo relatively frequent flooding (upper part of the river), as well as in those of the downstream part of the Meuse in which flow depths in the urbanized floodplains are particularly high when inundation occurs. This is the case of the city of Liege, as a result of a subsidence process following former mining activities. For a given climate scenario, the uncertainty ranges affecting flood risk estimates are significant; but not so much that the results for the different municipalities would overlap substantially. Therefore, these uncertainties do not hamper prioritization in terms of allocation of risk reduction measures at the municipality level. In the present climate, the uncertainties arising from flood frequency analysis have a negligible influence in the upper part of the river, while they have a considerable impact on risk modelling in the lower part, where a threshold effect was observed due to the flood protection structures (sudden transition from no inundation to massive flooding when a threshold discharge is exceeded). Varying the number of exceedance probabilities in the integration of the risk curve has different effects for different municipalities; but it does not change the ranking of the municipalities in terms of flood risk. For the other scenarios, damage estimation contributes most to the overall uncertainties. As shown by this study, the magnitude of the uncertainty and its main origin vary in space and in time. This emphasizes the paramount importance of conducting distributed uncertainty analyses. In the considered study area, prioritization of risk reduction means can be reliably performed despite the modelling uncertainties. Reference Detrembleur, S., Stilmant, F., Dewals, B., Erpicum, S., Archambeau, P., & Pirotton, M. (2015). Impacts of climate change on future flood damage on the river Meuse, with a distributed uncertainty analysis. Natural Hazards, 77(3), 1533-1549. Acknowledgement Part of this research was funded through the ARC grant for Concerted Research Actions, financed by the Wallonia-Brussels Federation. It was also supported by the NWE Interreg IVB Program.

Landsat classification of surface-water presence during multiple years to assess response of playa wetlands to climatic variability across the Great Plains Landscape Conservation Cooperative region

USGS Publications Warehouse

Manier, Daniel J.; Rover, Jennifer R.

2018-02-15

To improve understanding of the distribution of ecologically important, ephemeral wetland habitats across the Great Plains, the occurrence and distribution of surface water in playa wetland complexes were documented for four different years across the Great Plains Landscape Conservation Cooperative (GPLCC) region. This information is important because it informs land and wildlife managers about the timing and location of habitat availability. Data with an accurate timestamp that indicate the presence of water, the percent of the area inundated with water, and the spatial distribution of playa wetlands with water are needed for a host of resource inventory, monitoring, and research applications. For example, the distribution of inundated wetlands forms the spatial pattern of available habitat for resident shorebirds and water birds, stop-over habitats for migratory birds, connectivity and clustering of wetland habitats, and surface waters that recharge the Ogallala aquifer; there is considerable variability in the distribution of playa wetlands holding water through time. Documentation of these spatially and temporally intricate processes, here, provides data required to assess connections between inundation and multiple environmental drivers, such as climate, land use, soil, and topography. Climate drivers are understood to interact with land cover, land use and soil attributes in determining the amount of water that flows overland into playa wetlands. Results indicated significant spatial variability represented by differences in the percent of playas inundated among States within the GPLCC. Further, analysis-of-variance comparison of differences in inundation between years showed significant differences in all cases. Although some connections with seasonal moisture patterns may be observed, the complex spatial-temporal gradients of precipitation, temperature, soils, and land use need to be combined as covariates in multivariate models to effectively account for these patterns. We demonstrate the feasibility of using classification of Landsat satellite imagery to describe playa-wetland inundation across years and seasons. Evaluating classifications representing only 4 years of imagery, we found significant year-to-year and state-to-state differences in inundation rates.

Integration of coastal inundation modeling from storm tides to individual waves

NASA Astrophysics Data System (ADS)

Li, Ning; Roeber, Volker; Yamazaki, Yoshiki; Heitmann, Troy W.; Bai, Yefei; Cheung, Kwok Fai

2014-11-01

Modeling of storm-induced coastal inundation has primarily focused on the surge generated by atmospheric pressure and surface winds with phase-averaged effects of the waves as setup. Through an interoperable model package, we investigate the role of phase-resolving wave processes in simulation of coastal flood hazards. A spectral ocean wave model describes generation and propagation of storm waves from deep to intermediate water, while a non-hydrostatic storm-tide model has the option to couple with a spectral coastal wave model for computation of phase-averaged processes in a near-shore region. The ocean wave and storm-tide models can alternatively provide the wave spectrum and the surface elevation as the boundary and initial conditions for a nested Boussinesq model. Additional surface-gradient terms in the Boussinesq equations maintain the quasi-steady, non-uniform storm tide for modeling of phase-resolving surf and swash-zone processes as well as combined tide, surge, and wave inundation. The two nesting schemes are demonstrated through a case study of Hurricane Iniki, which made landfall on the Hawaiian Island of Kauai in 1992. With input from a parametric hurricane model and global reanalysis and tidal datasets, the two approaches produce comparable significant wave heights and phase-averaged surface elevations in the surf zone. The nesting of the Boussinesq model provides a seamless approach to augment the inundation due to the individual waves in matching the recorded debris line along the coast.

Water-Chemistry Evolution and Modeling of Radionuclide Sorption and Cation Exchange during Inundation of Frenchman Flat Playa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hershey, Ronald; Cablk, Mary; LeFebre, Karen

2013-08-01

Atmospheric tests and other experiments with nuclear materials were conducted on the Frenchman Flat playa at the Nevada National Security Site, Nye County, Nevada; residual radionuclides are known to exist in Frenchman Flat playa soils. Although the playa is typically dry, extended periods of winter precipitation or large single-event rainstorms can inundate the playa. When Frenchman Flat playa is inundated, residual radionuclides on the typically dry playa surface may become submerged, allowing water-soil interactions that could provide a mechanism for transport of radionuclides away from known areas of contamination. The potential for radionuclide transport by occasional inundation of the Frenchmanmore » Flat playa was examined using geographic information systems and satellite imagery to delineate the timing and areal extent of inundation; collecting water samples during inundation and analyzing them for chemical and isotopic content; characterizing suspended/precipitated materials and archived soil samples; modeling water-soil geochemical reactions; and modeling the mobility of select radionuclides under aqueous conditions. The physical transport of radionuclides by water was not evaluated in this study. Frenchman Flat playa was inundated with precipitation during two consecutive winters in 2009-2010 and 2010-2011. Inundation allowed for collection of multiple water samples through time as the areal extent of inundation changed and ultimately receded. During these two winters, precipitation records from a weather station in Frenchman Flat (Well 5b) provided information that was used in combination with geographic information systems, Landsat imagery, and image processing techniques to identify and quantify the areal extent of inundation. After inundation, water on the playa disappeared quickly, for example, between January 25, 2011 and February 10, 2011, a period of 16 days, 92 percent of the areal extent of inundation receded (2,062,800 m2). Water sampling provided valuable information about chemical processes occurring during inundation as the water disappeared. Important observations from water-chemistry analyses included: 1) total dissolved solids (TDS) and chloride ion (Cl-) concentrations were very low (TDS: < 200 mg/L and Cl-: < 3.0 mg/L, respectively) for all water samples regardless of time or areal extent; 2) all dissolved constituents were at concentrations well below what might be expected for evaporating shallow surface waters on a playa, even when 98 to 99 percent of the water had disappeared; 3) the amount of evaporation for the last water samples collected at the end of inundation, estimated with the stable isotopic ratios δ2H or δ18O, was approximately 60 percent; and 4) water samples analyzed by gamma spectroscopy did not show any man-made radioactivity; however, the short scanning time (24 hours) and relative chemical diluteness of the water samples (TDS ranged between 39 and 190 mg/L) may have contributed to none being detected. Additionally, any low-energy beta emitting radionuclides would not have been detected by gamma spectroscopy. From these observations, it was apparent that a significant portion of water on the playa did not evaporate, but rather infiltrated into the subsurface (approximately 40 percent). Consistent with this water chemistry-based conclusion is particle-size analysis of two archived Frenchman Flat playa soils samples, which showed low clay content in the near surface soil that also suggested infiltration. Infiltration of water from the playa during inundation into the subsurface does not necessarily imply that groundwater recharge is occurring, but it does provide a mechanism for moving residual radionuclides downward into the subsurface of Frenchman Flat playa. Water-mineral geochemical reactions were modeled so that changes in the water chemistry could be identified and the extent of reactions quantified. Geochemical modeling showed that evaporation; equilibrium with atmospheric carbon dioxide and calcite; dissolution of sodium chloride, gypsum, and composite volcanic glass; and precipitation of composite clay and quartz represented changes in water as it disappeared from the playa. This modeling provided an understanding of the water-soil geochemical environment, which was then used to evaluate the potential mobility of residual radionuclides into the playa soils by water. Because there is no information on the chemical forms of anthropogenic radionuclides in Frenchman Flat playa soil, it was assumed that soil radionuclides go into solution when the playa is inundated. In mobility modeling, a select group of radionuclides were allowed to sorb onto, or exchange with, playa soil minerals to evaluate the likelihood that the radionuclides would be removed from water during playa inundation. Radionuclide mobility modeling suggested that there would be minimal sorption or exchange of several important radionuclides (uranium, cesium, and technetium) with playa minerals such that they may be mobile in water when the playa is inundated and could infiltrate into the subsurface. Mobility modeling also showed that plutonium may be much less mobile because of sorption onto calcite, but the amount of reactive surface area of playa soil calcite is highly uncertain. Plutonium is also known to sorb onto colloidal particles suspended in water, suspended colloidal particles will move with the water, providing a mechanism to redistribute plutonium when Frenchman Flat playa is inundated. Water chemistry, stable isotopes, and geochemical modeling showed that residual radionuclides in Frenchman Flat playa soils could be mobilized in water when the playa is inundated with precipitation. Also, there is potential for these radionuclides to infiltrate into the subsurface with water. As a result of the information obtained both during this study and the conclusions drawn from it, additional data collection, investigation, and modeling are recommended. Specifically: sampling the playa soil to search for evidence of surface-water infiltration and the presence of radionuclides; developing a preliminary unsaturated flow and transport model to guide soil sampling; characterizing the chemical forms of radionuclides on the playa surface and any radionuclides that might have migrated into the subsurface; and, refining the unsaturated flow and transport model with data obtained from sampling and analysis of soil samples to guide any future sampling, development of remediation strategies, and defining risk-based boundaries for Frenchman Flat playa.« less

Living with floods - Household perception and satellite observations in the Barotse floodplain, Zambia

NASA Astrophysics Data System (ADS)

Cai, Xueliang; Haile, Alemseged Tamiru; Magidi, James; Mapedza, Everisto; Nhamo, Luxon

2017-08-01

The Barotse Floodplain, a designated Ramsar site, is home to thousands of indigenous people along with an extensive wetland ecosystem and food production system. Increasingly it is also a popular tourist destination with its annual Kuomboka festival which celebrates the relocation of the king and the Lozi people to higher ground before the onset of the flood season. This paper presents an integrated approach which cross validates and combines the floodplain residents' perceptions about recent floods with information on flood inundation levels derived from satellite observations. Local residents' surveys were conducted to assess farmers' perception on the flooding patterns and the impact on their livelihoods. Further, a series of flood inundation maps from 1989 to 2014 generated from remotely sensed Landsat imagery were used to assess the recent patterns of floods. Results show that the floodplain has a population of 33 thousand living in 10,849 small permeant or temporary buildings with a total cropland area of 4976 ha. The floodplain hydrology and flooding patterns have changed, confirmed by both surveys and satellite image analysis, due to catchment development and changing climate. The average annual inundated areas have increased from about 316 thousand ha in 1989-1998 to 488 thousand ha in 2005-2014. As a result the inundated cropland and houses increased from 9% to 6% in 1989 to 73% and 47% in 2014, respectively. The timing of the floods has also changed with both delaying and early onset happening more frequently. These changes cause increasing difficulties in flood forecast and preparation using indigenous knowledge, therefore creating greater damages to crops, livestock, and houses. Current floodplain management system is inadequate and new interventions are needed to help manage the floods at a systematic manner.

Scenario-based numerical modelling and the palaeo-historic record of tsunamis in Wallis and Futuna, Southwest Pacific

NASA Astrophysics Data System (ADS)

Lamarche, G.; Popinet, S.; Pelletier, B.; Mountjoy, J.; Goff, J.; Delaux, S.; Bind, J.

2015-08-01

We investigated the tsunami hazard in the remote French territory of Wallis and Futuna, Southwest Pacific, using the Gerris flow solver to produce numerical models of tsunami generation, propagation and inundation. Wallis consists of the inhabited volcanic island of Uvéa that is surrounded by a lagoon delimited by a barrier reef. Futuna and the island of Alofi form the Horn Archipelago located ca. 240 km east of Wallis. They are surrounded by a narrow fringing reef. Futuna and Alofi emerge from the North Fiji Transform Fault that marks the seismically active Pacific-Australia plate boundary. We generated 15 tsunami scenarios. For each, we calculated maximum wave elevation (MWE), inundation distance and expected time of arrival (ETA). The tsunami sources were local, regional and distant earthquake faults located along the Pacific Rim. In Wallis, the outer reef may experience 6.8 m-high MWE. Uvéa is protected by the barrier reef and the lagoon, but inundation depths of 2-3 m occur in several coastal areas. In Futuna, flow depths exceeding 2 m are modelled in several populated areas, and have been confirmed by a post-September 2009 South Pacific tsunami survey. The channel between the islands of Futuna and Alofi amplified the 2009 tsunami, which resulted in inundation distance of almost 100 m and MWE of 4.4 m. This first ever tsunami hazard modelling study of Wallis and Futuna compares well with palaeotsunamis recognised on both islands and observation of the impact of the 2009 South Pacific tsunami. The study provides evidence for the mitigating effect of barrier and fringing reefs from tsunamis.

Scenario-based numerical modelling and the palaeo-historic record of tsunamis in Wallis and Futuna, Southwest Pacific

NASA Astrophysics Data System (ADS)

Lamarche, G.; Popinet, S.; Pelletier, B.; Mountjoy, J.; Goff, J.; Delaux, S.; Bind, J.

2015-04-01

We investigated the tsunami hazard in the remote French territory of Wallis and Futuna, Southwest Pacific, using the Gerris flow solver to produce numerical models of tsunami generation, propagation and inundation. Wallis consists of the inhabited volcanic island of Uvéa that is surrounded by a lagoon delimited by a barrier reef. Futuna and the island of Alofi forms the Horn Archipelago located ca. 240 km east of Wallis. They are surrounded by a narrow fringing reef. Futuna and Alofi emerge from the North Fiji Transform Fault that marks the seismically active Pacific-Australia plate boundary. We generated fifteen tsunami scenarios. For each, we calculated maximum wave elevation (MWE), inundation distance, and Expected Time of Arrival (ETA). The tsunami sources were local, regional and distant earthquake faults located along the Pacific Rim. In Wallis, the outer reef may experience 6.8 m-high MWE. Uvéa is protected by the barrier reef and the lagoon, but inundation depths of 2-3 m occur in several coastal areas. In Futuna, flow depths exceeding 2 m are modelled in several populated areas, and have been confirmed by a post-September 2009 South Pacific tsunami survey. The channel between the islands of Futuna and Alofi amplified the 2009 tsunami, which resulted in inundation distance of almost 100 m and MWE of 4.4 m. This first-ever tsunami hazard modelling study of Wallis and Futuna compares well with palaeotsunamis recognised on both islands and observation of the impact of the 2009 South Pacific tsunami. The study provides evidence for the mitigating effect of barrier and fringing reefs from tsunamis.

The exposure of Sydney (Australia) to earthquake-generated tsunamis, storms and sea level rise: a probabilistic multi-hazard approach

PubMed Central

Dall'Osso, F.; Dominey-Howes, D.; Moore, C.; Summerhayes, S.; Withycombe, G.

2014-01-01

Approximately 85% of Australia's population live along the coastal fringe, an area with high exposure to extreme inundations such as tsunamis. However, to date, no Probabilistic Tsunami Hazard Assessments (PTHA) that include inundation have been published for Australia. This limits the development of appropriate risk reduction measures by decision and policy makers. We describe our PTHA undertaken for the Sydney metropolitan area. Using the NOAA NCTR model MOST (Method for Splitting Tsunamis), we simulate 36 earthquake-generated tsunamis with annual probabilities of 1:100, 1:1,000 and 1:10,000, occurring under present and future predicted sea level conditions. For each tsunami scenario we generate a high-resolution inundation map of the maximum water level and flow velocity, and we calculate the exposure of buildings and critical infrastructure. Results indicate that exposure to earthquake-generated tsunamis is relatively low for present events, but increases significantly with higher sea level conditions. The probabilistic approach allowed us to undertake a comparison with an existing storm surge hazard assessment. Interestingly, the exposure to all the simulated tsunamis is significantly lower than that for the 1:100 storm surge scenarios, under the same initial sea level conditions. The results have significant implications for multi-risk and emergency management in Sydney. PMID:25492514

The exposure of Sydney (Australia) to earthquake-generated tsunamis, storms and sea level rise: a probabilistic multi-hazard approach.

PubMed

Dall'Osso, F; Dominey-Howes, D; Moore, C; Summerhayes, S; Withycombe, G

2014-12-10

Approximately 85% of Australia's population live along the coastal fringe, an area with high exposure to extreme inundations such as tsunamis. However, to date, no Probabilistic Tsunami Hazard Assessments (PTHA) that include inundation have been published for Australia. This limits the development of appropriate risk reduction measures by decision and policy makers. We describe our PTHA undertaken for the Sydney metropolitan area. Using the NOAA NCTR model MOST (Method for Splitting Tsunamis), we simulate 36 earthquake-generated tsunamis with annual probabilities of 1:100, 1:1,000 and 1:10,000, occurring under present and future predicted sea level conditions. For each tsunami scenario we generate a high-resolution inundation map of the maximum water level and flow velocity, and we calculate the exposure of buildings and critical infrastructure. Results indicate that exposure to earthquake-generated tsunamis is relatively low for present events, but increases significantly with higher sea level conditions. The probabilistic approach allowed us to undertake a comparison with an existing storm surge hazard assessment. Interestingly, the exposure to all the simulated tsunamis is significantly lower than that for the 1:100 storm surge scenarios, under the same initial sea level conditions. The results have significant implications for multi-risk and emergency management in Sydney.

Distribution and sedimentary characteristics of tsunami deposits along the Cascadia margin of western North America

USGS Publications Warehouse

Peters, R.; Jaffe, B.; Gelfenbaum, G.

2007-01-01

Tsunami deposits have been found at more than 60 sites along the Cascadia margin of Western North America, and here we review and synthesize their distribution and sedimentary characteristics based on the published record. Cascadia tsunami deposits are best preserved, and most easily identified, in low-energy coastal environments such as tidal marshes, back-barrier marshes and coastal lakes where they occur as anomalous layers of sand within peat and mud. They extend up to a kilometer inland in open coastal settings and several kilometers up river valleys. They are distinguished from other sediments by a combination of sedimentary character and stratigraphic context. Recurrence intervals range from 300-1000??years with an average of 500-600??years. The tsunami deposits have been used to help evaluate and mitigate tsunami hazards in Cascadia. They show that the Cascadia subduction zone is prone to great earthquakes that generate large tsunamis. The inclusion of tsunami deposits on inundation maps, used in conjunction with results from inundation models, allows a more accurate assessment of areas subject to tsunami inundation. The application of sediment transport models can help estimate tsunami flow velocity and wave height, parameters which are necessary to help establish evacuation routes and plan development in tsunami prone areas. ?? 2007.

An evaluation of the application of treated sewage effluents in Las Tablas de Daimiel National Park, Central Spain

NASA Astrophysics Data System (ADS)

Navarro, Vicente; García, Beatriz; Sánchez, David; Asensio, Laura

2011-04-01

SummaryAt the present time there is not enough information available to develop a quantitative model on how inundation takes place in the 1490 ha area of Tablas de Daimiel National Park (Central Spain) located upstream of Morenillo Dam. Given that it is the most important area in the Park from an ecological standpoint, this is a major concern, as it has not been possible to assess the potential effectiveness of the interventions geared towards improving its current state. As a result, it is not feasible to simulate the hydrologic response to the application of treated sewage effluents, an initiative recently implemented by the Public Administration responsible for water management in the Guadiana River Basin, where the Park is located. To help solve this problem, a simplified model of the hydrologic behaviour of the system has been developed focusing on the characterisation of the main trends of the inundation process. Field data from 12 drying processes were used to identify the model parameters. Later, the evolution of the system was examined after the application of treated sewage effluents, assuming the hypothesis of a dry climate. The results show that the 10 Mm 3 of available effluents is sufficient to improve from 2 ha to 60 ha the inundation condition of the areas considered to be high-priority. This therefore demonstrates that, from a hydrologic point of view, it is highly advisable to use treated sewage effluents.

Applications of Remote Sensing for Studying Lateral Carbon Fluxes and Inundation Dynamics in Tidal Wetlands

NASA Astrophysics Data System (ADS)

Lamb, B. T.; Tzortziou, M.; McDonald, K. C.

2017-12-01

Wetlands play a key role in Earth's carbon cycle. However, wetland carbon cycling exhibits a high level of spatiotemporal dynamism, and thus, is not as well understood as carbon cycling in other ecosystems. In order to accurately characterize wetland carbon cycling and fluxes, wetland vegetation phenology, seasonal inundation dynamics, and tidal regimes must be understood as these factors influence carbon generation and transport. Here, we use radar remote sensing to map wetland properties in the Chesapeake Bay, the largest estuary in the United States with more than 1,500 square miles of tidal wetlands, across a range of tidal amplitudes, salinity regimes, and soil organic matter content levels. We have been using Sentinel-1 and ALOS PALSAR-1 radar measurements to characterize vegetation and seasonal inundation dynamics with the future goal of characterizing salinity gradients and tidal regimes. Differences in radar backscatter from various surface targets has been shown to effectively discriminate between dry soil, wet soil, vegetated areas, and open water. Radar polarization differences and ratios are particularly effective at distinguishing between vegetated and non-vegetated areas. Utilizing these principles, we have been characterizing wetland types using supervised classification techniques including: Random Forest, Maximum Likelihood, and Minimum Distance. The National Wetlands Inventory has been used as training and validation data. Ideally, the techniques we outline in this research will be applicable to the characterization of wetlands in coastal areas outside of Chesapeake Bay.

Redd dewatering effects on hatching and larval survival of the robust redhorse

USGS Publications Warehouse

Fisk, J. M.; Kwak, Thomas J.; Heise, R. J.; Sessions, F. W.

2013-01-01

Riverine habitats have been altered and fragmented from hydroelectric dams and change spatially and temporally with hydropower flow releases. Hydropeaking flow regimes for electrical power production inundate areas that create temporary suitable habitat for fish that may be rapidly drained. Robust redhorse Moxostoma robustum, an imperiled, rare fish species, uses such temporary habitats to spawn, but when power generation ceases, these areas are dewatered until the next pulse of water is released. We experimentally simulated the effects of dewatering periods on the survival of robust redhorse eggs and larvae in the laboratory. Robust redhorse eggs were placed in gravel in eyeing-hatching jars (three jars per treatment) and subjected to one of four dewatering periods (6, 12, 24 and 48 h), followed by 12 h of inundation for each treatment, and a control treatment was never dewatered. Egg desiccation was observed in some eggs in the 24- and 48-h treatments after one dewatering period. For all treatments except the control, the subsequent dewatering period after eggs hatched was lethal. Larval emergence for the control treatment was observed on day 5 post-hatching and continued until the end of the experiment (day 21). Larval survival was significantly different between the control and all dewatering treatments for individuals in the gravel. These findings support the need for hydropower facilities to set minimum flows to maintain inundation of spawning areas for robust redhorse and other species to reduce dewatering mortality.

Geological record of tsunami inundations in Pantano Morghella (south-eastern Sicily) both from near and far-field sources

NASA Astrophysics Data System (ADS)

Gerardi, F.; Smedile, A.; Pirrotta, C.; Barbano, M. S.; De Martini, P. M.; Pinzi, S.; Gueli, A. M.; Ristuccia, G. M.; Stella, G.; Troja, S. O.

2012-04-01

Analysis of tsunami deposits from the Pantano Morghella area provided geological evidence for two inundations occurred along the south-eastern Ionian coast of Sicily. Pantano Morghella is a large pond characterised by a fine-grained sedimentation indicating a low-energy depositional environment. Two anomalous yellow sandy layers found at different depths indicate the occurrence of high-energy marine inundations. We studied sedimentological and paleontological features of the anomalous deposits as well as their spatial distribution observing the following properties: different facies with respect to the local stratigraphic sequence; erosive bases, rip-up clasts and broken elements testifying violent deposition mechanisms; macro and micro fauna of marine environment; relatively constant thickness throughout most of the depositional zone with thinning at the distal end; large sand sheets that extend inland. These observations, jointly with their infrequency in the sedimentary record and the age indicating a fast deposition, provided strong evidence for tsunami inundations. Correlations between anomalous layers and historical tsunamis are supported by radiocarbon and OSL dating results. The younger deposit is likely due to the 1908 near-source tsunami, whereas the flooding of the oldest event is most likely associated with a far and large source, the Crete 365 AD earthquake.

The Mount Rainier Lahar Detection System

NASA Astrophysics Data System (ADS)

Lockhart, A. B.; Murray, T. L.

2003-12-01

To mitigate the risk of unheralded lahars from Mount Rainier, the U.S. Geological Survey, in cooperation with Pierce County, Washington, installed a lahar-detection system on the Puyallup and Carbon rivers that originate on Mount Rainier's western slopes. The system, installed in 1998, is designed to automatically detect the passage of lahars large enough to potentially affect populated areas downstream (approximate volume threshold 40 million cubic meters), while ignoring small lahars, earthquakes, extreme weather and floods. Along each river valley upstream, arrays of independent lahar-monitoring stations equipped with geophones and short tripwires telemeter data to a pair of redundant computer base stations located in and near Tacoma at existing public safety facilities that are staffed around the clock. Monitored data consist of ground-vibration levels, tripwire status, and transmissions at regular intervals. The base stations automatically evaluate these data to determine if a dangerous lahar is passing through the station array. The detection algorithm requires significant ground vibration to occur at those stations in the array that are above the anticipated level of inundation, while lower level `deadman' stations, inundated by the flow, experience tripwire breakage or are destroyed. Once a base station detects a lahar, it alerts staff who execute a call-down of public-safety officials and schools, initiating evacuation of areas potentially at risk. Because the system's risk-mitigation task imposes high standards of reliability on all components, it has been under test for several years. To date, the system has operated reliably and without false alarms, including during the nearby M6.8 Nisqually Earthquake on February 28, 2001. The system is being turned over to Pierce County, and activated as part of their lahar warning system.

Proximal lava drainage controls on basaltic fissure eruption dynamics

NASA Astrophysics Data System (ADS)

Jones, T. J.; Llewellin, E. W.; Houghton, B. F.; Brown, R. J.; Vye-Brown, C.

2017-11-01

Hawaiian basaltic eruptions commonly initiate as a fissure, producing fountains, spattering, and clastogenic lava flows. Most fissures rapidly localize to form a small number of eruptive vents, the location of which may influence the subsequent distribution of lava flows and associated hazards. We present results from a detailed field investigation of the proximal deposits of episode 1 of the 1969 fissure eruption of Mauna Ulu, Kīlauea, Hawai`i. Exceptional preservation of the deposits allows us to reconstruct vent-proximal lava drainage patterns and to assess the role that drainage played in constraining vent localization. Through detailed field mapping, including measurements of the height and internal depth of lava tree moulds, we reconstruct high-resolution topographic maps of the pre-eruption ground surface, the lava high-stand surface and the post-eruption ground surface. We calculate the difference in elevation between pairs of maps to estimate the lava inundation depth and lava drainage depth over the field area and along different segments of fissure. Aerial photographs collected during episode 1 of the eruption allow us to locate those parts of the fissure that are no longer exposed at the surface. By comparing with the inundation and drainage maps, we find that fissure segments that were inundated with lava to greater depths (typically 1-6 m) during the eruption later became foci of lava drainage back into the fissure (internal drain-back). We infer that, in these areas, lava ponding over the fissure suppressed discharge of magma, thereby favouring drain-back and stagnation. By contrast, segments with relatively shallow inundation (typically less than 1 m), such as where the fissure intersects pre-eruptive topographic highs, or where flow away from the vent (outflow) was efficient, are often associated with sub-circular vent geometries in the post-eruption ground surface. We infer that these parts of the fissure became localization points for ongoing magma ascent and discharge. We conclude that lava inundation and drainage processes in basaltic fissure eruptions can play an important role in controlling their localization and longevity.

What is missing? An operational inundation mapping framework by SAR data

NASA Astrophysics Data System (ADS)

Shen, X.; Anagnostou, E. N.; Zeng, Z.; Kettner, A.; Hong, Y.

2017-12-01

Compared to optical sensors, synthetic aperture radar (SAR) works all-day all-weather. In addition, its spatial resolution does not decrease with the height of the platform and is thus applicable to a range of important studies. However, existing studies did not address the operational demands of real-time inundation mapping. The direct proof is that no water body product exists for any SAR-based satellites. Then what is missing between science and products? Automation and quality. What makes it so difficult to develop an operational inundation mapping technique based on SAR data? Spectrum-wise, unlike optical water indices such as MNDWI, AWEI etc., where a relative constant threshold may apply across acquisition of images, regions and sensors, the threshold to separate water from non-water pixels in each SAR images has to be individually chosen. The optimization of the threshold is the first obstacle to the automation of the SAR data algorithm. Morphologically, the quality and reliability of the results have been compromised by over-detection caused by smooth surface and shadowing area, the noise-like speckle and under-detection caused by strong-scatter disturbance. In this study, we propose a three-step framework that addresses all aforementioned issues of operational inundation mapping by SAR data. The framework consists of 1) optimization of Wishart distribution parameters of single/dual/fully-polarized SAR data, 2) morphological removal of over-detection, and 3) machine-learning based removal of under-detection. The framework utilizes not only the SAR data, but also the synergy of digital elevation model (DEM), and optical sensor-based products of fine resolution, including the water probability map, land cover classification map (optional), and river width. The framework has been validated throughout multiple areas in different parts of the world using different satellite SAR data and globally available ancillary data products. Therefore, it has the potential to contribute as an operational inundation mapping algorithm to any SAR missions, such as SWOT, ALOS, Sentinel, etc. Selected results using ALOS/PALSAR-1 L-band dual polarized data around the Connecticut River is provided in the attached Figure.

Investigating Typhoon Induced River-Surge Interactions in the Tamsui Estuary, Taiwan.

NASA Astrophysics Data System (ADS)

Maskell; J. H.; Grieser, J.; Rodney, J.; Howe, N. J.

2016-02-01

It is increasingly important to understand the combined influence of the main drivers of coastal risk due to sea level rise and the potential increase in extreme weather events. An Asian Basin stochastic typhoon set was used to force a storm surge model of Taiwan to investigate the interaction between storm surge and high river discharges (50, 100 and 200 year return period discharges) in the Tamsui River. Taiwan is a mountainous country leading to the combined risk of surge and high river discharge occurring simultaneously in estuary regions. The typhoon tracks were selected using a Hurricane Surge Index (Kantha, 2006) and cross the northern tip of Taiwan with maximum sustained winds (Vmax) between 51 m/s and 75 m/s (Cat 3-5). Peak surge elevations in the Tamsui River range from 5.7 m to 10.3 m. The surge interacts with the river flow to induce changes in the water elevation between -8 m and 4 m depending on the surge elevation and river discharge and increases the inundated area in the range 37 km to 204 km. Significant positive interactions occur in the Tamsui Estuary (Fig. 1a) but do not have implications for increased inundation and occur at the start of the flood phase and the end of the ebb phase as previously shown in idealized test cases (Maskell et al., 2013). Current vectors in the estuary show that at the time leading up to high water the river outflow starts to become dominant in the mid-channel reducing maximum water levels by up to 10% in the combined surge and river solution. However, surge inhibits downstream propagation of the flood wave in the upper river channels increasing water levels by up to 2 m. The maximum inundated area (1330 km2) is caused by the combination of defence overflow due to the maximum surge (10.27 m) and increased river levels (RP100) in the upper channels leading to significant inundation either side of the Keelung River (Fig. 1b). The Erchung floodway is effective in diverting some of the flow (up to 10,443 m3/s) reducing inundation elsewhere in the river network.

Modelling land-atmosphere interactions in tropical African wetlands

NASA Astrophysics Data System (ADS)

Dadson, S.

2012-04-01

Wetlands interact with the climate system in two ways. First, the availability of water at the land surface introduces important feedbacks on climate via surface fluxes of energy and water [1]. Over wet surfaces, high daytime evaporation rates and suppressed sensible heat fluxes induce a shallower, moister planetary boundary layer, which affects atmospheric instability and favours the initiation of new storms [2]. Second, wetlands form a key link between the hydrological and carbon cycles, via anoxic degradation of organic matter to release methane (CH4). Wetlands are the largest, but least well quantified, single source of CH4, with recent emission estimates ranging from 105-278 Tg yr-1, ~75% of which comes from the tropics [3]. Although the emissions of methane from boreal wetlands and lakes are less than those from tropical wetlands [3], their size and remoteness pose significant challenges to the quantification of their feedbacks to regional and global climate. In this paper, I present a summary of recent work on modelling hydrological and biogeochemical aspects of wetland formation and the associated land-atmosphere feedbacks in African and boreal environments. We have added an overbank inundation model to the Joint UK Land Environment Simulator (JULES). Sub-grid topographic data were used to derive a two-parameter frequency distribution of inundated areas. Our predictions of inundated area are in good agreement with observed estimates of the extent of inundation obtained using satellite infrared and microwave remote sensing [4,5]. The model predicts significant evaporative losses from the inundated region accounting for doubling of the total land-atmosphere water flux during periods of greatest flooding. I also present new parameterisations of methane generation from wetlands. 1. Koster, R.D., et al., 2004, Science, 305(5687): 1138-40. 2. Taylor, C.M., 2010, Geophys. Res. Lett., 37: L05406. 3. US EPA, 2010, Methane and Nitrous Oxide Emissions From Natural Sources, Report EPA 430-R-10-001. 4. S.J. Dadson, et al., 2010, Journal of Geophysical Research, 115, D23114 5. F. Papa, et al., 2010, Journal of Geophysical Research, 115, D12111, doi:10.1029/2009JD012674.

Rapid Determination of Appropriate Source Models for Tsunami Early Warning using a Depth Dependent Rigidity Curve: Method and Numerical Tests

NASA Astrophysics Data System (ADS)

Tanioka, Y.; Miranda, G. J. A.; Gusman, A. R.

2017-12-01

Recently, tsunami early warning technique has been improved using tsunami waveforms observed at the ocean bottom pressure gauges such as NOAA DART system or DONET and S-NET systems in Japan. However, for tsunami early warning of near field tsunamis, it is essential to determine appropriate source models using seismological analysis before large tsunamis hit the coast, especially for tsunami earthquakes which generated significantly large tsunamis. In this paper, we develop a technique to determine appropriate source models from which appropriate tsunami inundation along the coast can be numerically computed The technique is tested for four large earthquakes, the 1992 Nicaragua tsunami earthquake (Mw7.7), the 2001 El Salvador earthquake (Mw7.7), the 2004 El Astillero earthquake (Mw7.0), and the 2012 El Salvador-Nicaragua earthquake (Mw7.3), which occurred off Central America. In this study, fault parameters were estimated from the W-phase inversion, then the fault length and width were determined from scaling relationships. At first, the slip amount was calculated from the seismic moment with a constant rigidity of 3.5 x 10**10N/m2. The tsunami numerical simulation was carried out and compared with the observed tsunami. For the 1992 Nicaragua tsunami earthquake, the computed tsunami was much smaller than the observed one. For the 2004 El Astillero earthquake, the computed tsunami was overestimated. In order to solve this problem, we constructed a depth dependent rigidity curve, similar to suggested by Bilek and Lay (1999). The curve with a central depth estimated by the W-phase inversion was used to calculate the slip amount of the fault model. Using those new slip amounts, tsunami numerical simulation was carried out again. Then, the observed tsunami heights, run-up heights, and inundation areas for the 1992 Nicaragua tsunami earthquake were well explained by the computed one. The other tsunamis from the other three earthquakes were also reasonably well explained by the computed ones. Therefore, our technique using a depth dependent rigidity curve is worked to estimate an appropriate fault model which reproduces tsunami heights near the coast in Central America. The technique may be worked in the other subduction zones by finding a depth dependent rigidity curve in that particular subduction zone.

Current & future vulnerability of sarasota county Florida to hurricane storm surge & sea level rise

USGS Publications Warehouse

Frazier, T.; Wood, N.; Yarnal, B.

2008-01-01

Coastal communities in portions of the United States are vulnerable to storm-surge inundation from hurricanes and this vulnerability will likely increase, given predicted rises in sea level from climate change and growing coastal development. In this paper, we provide an overview of research to determine current and future societal vulnerability to hurricane storm-surge inundation and to help public officials and planners integrate these scenarios into their long-range land use plans. Our case study is Sarasota County, Florida, where planners face the challenge of balancing increasing population growth and development with the desire to lower vulnerability to storm surge. Initial results indicate that a large proportion of Sarasota County's residential and employee populations are in areas prone to storm-surge inundation from a Category 5 hurricane. This hazard zone increases when accounting for potential sea-level-rise scenarios, thereby putting additional populations at risk. Subsequent project phases involve the development of future land use and vulnerability scenarios in collaboration with local officials. Copyright ASCE 2008.

Standards and Guidelines for Numerical Models for Tsunami Hazard Mitigation

NASA Astrophysics Data System (ADS)

Titov, V.; Gonzalez, F.; Kanoglu, U.; Yalciner, A.; Synolakis, C. E.

2006-12-01

An increased number of nations around the workd need to develop tsunami mitigation plans which invariably involve inundation maps for warning guidance and evacuation planning. There is the risk that inundation maps may be produced with older or untested methodology, as there are currently no standards for modeling tools. In the aftermath of the 2004 megatsunami, some models were used to model inundation for Cascadia events with results much larger than sediment records and existing state-of-the-art studies suggest leading to confusion among emergency management. Incorrectly assessing tsunami impact is hazardous, as recent events in 2006 in Tonga, Kythira, Greece and Central Java have suggested (Synolakis and Bernard, 2006). To calculate tsunami currents, forces and runup on coastal structures, and inundation of coastlines one must calculate the evolution of the tsunami wave from the deep ocean to its target site, numerically. No matter what the numerical model, validation (the process of ensuring that the model solves the parent equations of motion accurately) and verification (the process of ensuring that the model used represents geophysical reality appropriately) both are an essential. Validation ensures that the model performs well in a wide range of circumstances and is accomplished through comparison with analytical solutions. Verification ensures that the computational code performs well over a range of geophysical problems. A few analytic solutions have been validated themselves with laboratory data. Even fewer existing numerical models have been both validated with the analytical solutions and verified with both laboratory measurements and field measurements, thus establishing a gold standard for numerical codes for inundation mapping. While there is in principle no absolute certainty that a numerical code that has performed well in all the benchmark tests will also produce correct inundation predictions with any given source motions, validated codes reduce the level of uncertainty in their results to the uncertainty in the geophysical initial conditions. Further, when coupled with real--time free--field tsunami measurements from tsunameters, validated codes are the only choice for realistic forecasting of inundation; the consequences of failure are too ghastly to take chances with numerical procedures that have not been validated. We discuss a ten step process of benchmark tests for models used for inundation mapping. The associated methodology and algorithmes have to first be validated with analytical solutions, then verified with laboratory measurements and field data. The models need to be published in the scientific literature in peer-review journals indexed by ISI. While this process may appear onerous, it reflects our state of knowledge, and is the only defensible methodology when human lives are at stake. Synolakis, C.E., and Bernard, E.N, Tsunami science before and beyond Boxing Day 2004, Phil. Trans. R. Soc. A 364 1845, 2231--2263, 2005.

Nest inundation from sea-level rise threatens sea turtle population viability.

PubMed

Pike, David A; Roznik, Elizabeth A; Bell, Ian

2015-07-01

Contemporary sea-level rise will inundate coastal habitats with seawater more frequently, disrupting the life cycles of terrestrial fauna well before permanent habitat loss occurs. Sea turtles are reliant on low-lying coastal habitats worldwide for nesting, where eggs buried in the sand remain vulnerable to inundation until hatching. We show that saltwater inundation directly lowers the viability of green turtle eggs (Chelonia mydas) collected from the world's largest green turtle nesting rookery at Raine Island, Australia, which is undergoing enigmatic decline. Inundation for 1 or 3 h reduced egg viability by less than 10%, whereas inundation for 6 h reduced viability by approximately 30%. All embryonic developmental stages were vulnerable to mortality from saltwater inundation. Although the hatchlings that emerged from inundated eggs displayed normal physical and behavioural traits, hypoxia during incubation could influence other aspects of the physiology or behaviour of developing embryos, such as learning or spatial orientation. Saltwater inundation can directly lower hatching success, but it does not completely explain the consistently low rates of hatchling production observed on Raine Island. More frequent nest inundation associated with sea-level rise will increase variability in sea turtle hatching success spatially and temporally, due to direct and indirect impacts of saltwater inundation on developing embryos.

Nest inundation from sea-level rise threatens sea turtle population viability

PubMed Central

Pike, David A.; Roznik, Elizabeth A.; Bell, Ian

2015-01-01

Contemporary sea-level rise will inundate coastal habitats with seawater more frequently, disrupting the life cycles of terrestrial fauna well before permanent habitat loss occurs. Sea turtles are reliant on low-lying coastal habitats worldwide for nesting, where eggs buried in the sand remain vulnerable to inundation until hatching. We show that saltwater inundation directly lowers the viability of green turtle eggs (Chelonia mydas) collected from the world's largest green turtle nesting rookery at Raine Island, Australia, which is undergoing enigmatic decline. Inundation for 1 or 3 h reduced egg viability by less than 10%, whereas inundation for 6 h reduced viability by approximately 30%. All embryonic developmental stages were vulnerable to mortality from saltwater inundation. Although the hatchlings that emerged from inundated eggs displayed normal physical and behavioural traits, hypoxia during incubation could influence other aspects of the physiology or behaviour of developing embryos, such as learning or spatial orientation. Saltwater inundation can directly lower hatching success, but it does not completely explain the consistently low rates of hatchling production observed on Raine Island. More frequent nest inundation associated with sea-level rise will increase variability in sea turtle hatching success spatially and temporally, due to direct and indirect impacts of saltwater inundation on developing embryos. PMID:26587269

Flood on Big Fossil Creek at Haltom City near Fort Worth, Texas, in 1962

USGS Publications Warehouse

Montgomery, John H.; Ruggles, Frederick H.; Patterson, James Lee

1965-01-01

The approximate area inundated near Fort Worth, Texas, by Big Fossil Creek, during the flood of September 7, 1962, is shown on a topographic map to record the flood hazard in graphic form. Big Fossil Creek, which drains an area of 74.7 square miles, flows generally southeastward along the northeast edge of Fort Worth through Richland Hills and Haltom City, into West Fork Trinity River. The flood of September 7, 1962, the greatest in Richland Hills since at least 1900 was the result of a high rate of discharge from the area upstream from the confluence of Big Fossil Creek and Whites Branch. Greater floods are possible, but no attempt has been made to show their probable overflow limits. Future protective works may reduce the frequency of flooding in the area but will not necessarily eliminate flooding. Changes in culture such as new highways and bridges and changes in land use may influence the inundation pattern of future floods. Mapping of the West Fork Trinity River flood was beyond the scope of the Big Fossil Creek study, and is not shown.

Impact of Water Level on Carbon Sequestration at a Sub-tropical Peat Marsh

NASA Astrophysics Data System (ADS)

Sumner, D.; Hinkle, C.; Li, J.

2012-12-01

The impact of water level on sub-tropical peat marsh atmospheric/landscape carbon exchange was explored through eddy-covariance measurement of carbon dioxide and methane fluxes over a site at Blue Cypress Conservation Area in Florida. This site is vegetated with tall, dense sawgrass (Cladium jamaicense) and a thick accumulation of peat (over 3 m) suggesting a historically high primary productivity and carbon sequestration. Water managers are particularly interested in understanding how water-level controls can be directed to maintain topography through avoidance of excessive drought-induced oxidative losses of peat soil, as well as to minimize releases of greenhouse gases to the atmosphere. Comparison of net ecosystem productivity (NEP) during a wet year of continuous inundation and a drier year with a 9-month hydroperiod (NEP of 710 and 180 g C/m2/yr, respectively) suggests the positive impact of inundation on sequestration of carbon dioxide. These results are counter to previous research in short stature (1 m or less) sawgrass marshes in the Florida Everglades which indicate suppression of productivity during inundation. This seeming contradiction is probably best explained by the tall stature (over 2 m) of sawgrass at the study site in which inundation still does not cover a substantial fraction of the green leaves and the lower canopy is largely composed of brown and decaying leaves. Gross ecosystem productivity (GEP) was suppressed during the dry year (GEP = 1380 and 1030 g C/m2/yr for wet and dry years, respectively), probably as a consequence of canopy moisture stress. Respiration (R) was enhanced the year when water levels were farthest below land surface (R = 670 and 850 g C/m2/yr for wet and dry years, respectively) as a result of soil oxidation. GEP remained suppressed during the dry year even after re-flooding, probably because of relatively low photosynthetic leaf area that was the legacy of reduced canopy growth rates during the drought. Over a seven-month measurement period spanning a dry-to-inundated transition in the marsh, methane flux was negligible during non-inundated periods, but was substantial (averaging 80 g C/m2/yr) during wet periods. The results of this study suggest that water level is a critical control on atmospheric carbon exchanges at this peat marsh with implications for water management and strategic planning under potentially drier conditions that might occur in response to climate change.

Impact of Water Level on Carbon Sequestration at a Sub-tropical Peat Marsh

NASA Astrophysics Data System (ADS)

Sumner, D.; Hinkle, C.; Graham, S.; Li, J.

2013-12-01

The impact of water level on sub-tropical peat marsh atmospheric/landscape carbon exchange was explored through eddy-covariance measurement of carbon dioxide and methane fluxes over a site at Blue Cypress Conservation Area in Florida. This site is vegetated with tall, dense sawgrass (Cladium jamaicense) and a thick accumulation of peat (over 3 m) suggesting a historically high primary productivity and carbon sequestration. Water managers are particularly interested in understanding how water-level controls can be directed to maintain topography through avoidance of excessive drought-induced oxidative losses of peat soil, as well as to minimize releases of greenhouse gases to the atmosphere. Comparison of net ecosystem productivity (NEP) during a wet year of continuous inundation and a drier year with a 9-month hydroperiod (NEP of 710 and 180 g C/m2/yr, respectively) suggests the positive impact of inundation on sequestration of carbon dioxide. These results are counter to previous research in short stature (1 m or less) sawgrass marshes in the Florida Everglades which indicate suppression of productivity during inundation. This seeming contradiction is probably best explained by the tall stature (over 2 m) of sawgrass at the study site in which inundation still does not cover a substantial fraction of the green leaves and the lower canopy is largely composed of brown and decaying leaves. Gross ecosystem productivity (GEP) was suppressed during the dry year (GEP = 1380 and 1030 g C/m2/yr for wet and dry years, respectively), probably as a consequence of canopy moisture stress. Respiration (R) was enhanced the year when water levels were farthest below land surface (R = 670 and 850 g C/m2/yr for wet and dry years, respectively) as a result of soil oxidation. GEP remained suppressed during the dry year even after re-flooding, probably because of relatively low photosynthetic leaf area that was the legacy of reduced canopy growth rates during the drought. Over a seven-month measurement period spanning a dry-to-inundated transition in the marsh, methane flux was negligible during non-inundated periods, but was substantial (averaging 80 g C/m2/yr) during wet periods. The results of this study suggest that water level is a critical control on atmospheric carbon exchanges at this peat marsh with implications for water management and strategic planning under potentially drier conditions that might occur in response to climate change.

Environmental impact assessment of the 2011 Tohoku-oki tsunami on the Sendai Plain

NASA Astrophysics Data System (ADS)

Chagué-Goff, Catherine; Niedzielski, Przemyslaw; Wong, Henri K. Y.; Szczuciński, Witold; Sugawara, Daisuke; Goff, James

2012-12-01

Large areas of farmland in the Sendai Plain, Japan, were inundated by the 11 March 2011 Tohoku-oki tsunami and covered by a discontinuous 30-0.2 cm thick sediment layer consisting of sand and/or mud and generally thinning and fining inland. Two months after the tsunami, numerous rice paddy fields and depressions remained ponded with brackish or saline water. A series of field surveys in May, August and October 2011 were carried out north of Sendai airport, in order to assess the environmental impact of the tsunami. While evaporation had resulted in elevated conductivity in ponded water in May (up to 68.2 mS cm- 1), rainfall over the next five months led to dilution, although brackish water was still recorded in depressions and on paddy fields. Tsunami sediments, underlying soil and soil beyond the tsunami inundation limit were collected at 43 sites along and near a transect extending over 5 km inland, and analysed for grain size, organic content, water leachable ions, acid leachable metals and exchangeable metalloids. Water leachable anion and cation concentrations were elevated in sandy and muddy tsunami deposits and soils particularly in areas, where seawater had stagnated for a longer period of time after the tsunami, with up to 10.5% Cl, 6.6% Na, 2.8% SO4, 440 mg kg- 1 Br measured in surface sediments (< 0.5 cm depth). Vertical variations were also recorded, with higher concentrations often measured in the surface samples. A similar trend could be observed for some of the metalloids (As) and metals (Zn, Cu and Ni), although in general, maximum concentrations of metals and metalloids were not much higher than in soils not inundated by the tsunami and were within background levels for uncontaminated Japanese soils. The impact of saltwater inundation was documented in the chemistry of soils underlying tsunami sediments, which were affected by salt contamination down to ~ 15 cm depth, and soils not covered by tsunami deposits. The latter implies that the extent of tsunami inundation may successfully be determined using geochemical markers in absence of any sedimentological evidence. Water leachable ions mostly decreased over time, however, they remained high enough to impact on rice farming, which was completely halted in 2011. Although further work is required to assess the longer term impact of tsunami inundation, flushing of salt with freshwater, as well as the possible removal of sandy/muddy sediments and underlying soil are recommended to allow crop production to resume.

Flood boundaries and water-surface profile for the computed 100-year flood, Swift Creek at Afton, Wyoming, 1986

USGS Publications Warehouse

Rankl, James G.; Wallace, Joe C.

1989-01-01

Flood flows on Swift Creek near Afton, Wyoming, were analyzed. Peak discharge with an average recurrence interval of 100 years was computed and used to determine the flood boundaries and water surface profile in the study reach. The study was done in cooperation with Lincoln County and the Town of Afton to determine the extent of flooding in the Town of Afton from a 100-year flood on Swift Creek. The reach of Swift Creek considered in the analysis extends upstream from the culvert at Allred County Road No. 12-135 to the US Geological Survey streamflow-gaging station located in the Bridger National Forest , a distance of 3.2 miles. Boundaries of the 100-year flood are delineated on a map using the computed elevation of the flood at each cross section, survey data, and a 1983 aerial photograph. The computed water surface elevation for the 100-year flood was plotted at each cross section, then the lateral extent of the flood was transferred to the flood map. Boundaries between cross sections were sketched using information taken from the aerial photograph. Areas that are inundated, but not part of the active flow, are designated on the cross sections. (Lantz-PTT)

Development of Local Amplification Factors in the NEAM Region for Production of Regional Tsunami Hazard Maps

NASA Astrophysics Data System (ADS)

Harbitz, C. B.; Glimsdal, S.; Løvholt, F.; Orefice, S.; Romano, F.; Brizuela, B.; Lorito, S.; Hoechner, A.; Babeyko, A. Y.

2016-12-01

The standard way of estimating tsunami inundation is by applying numerical depth-averaged shallow-water run-up models. However, for a regional Probabilistic Tsunami Hazard Assessment (PTHA), applying such inundation models may be too time-consuming. A faster, yet less accurate procedure, is to relate the near-shore surface elevations at offshore points to maximum shoreline water levels by using a set of amplification factors based on the characteristics of the incident wave and the bathymetric slope. The surface elevation at the shoreline then acts as a rough approximation for the maximum inundation height or run-up height along the shoreline. An amplification-factor procedure based on a limited set of idealized broken shoreline segments has previously been applied to estimate the maximum inundation heights globally. Here, we present a study where this technique is developed further, by taking into account the local bathymetric profiles. We extract a large number of local bathymetric transects over a significant part of the North East Atlantic, the Mediterranean and connected seas (NEAM) region. For each bathymetric transect, we compute the wave amplification from an offshore control point to points close to the shoreline using a linear shallow-water model for waves of different period and polarity with a sinusoidal pulse wave as input. The amplification factors are then tabulated. We present maximum water levels from the amplification factor method, and compare these with results from conventional inundation models. Finally, we demonstrate how the amplification factor method can be convolved with PTHA results to provide regional tsunami hazard maps. This work has been supported by the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement 603839 (Project ASTARTE), and the TSUMAPS-NEAM Project (http://www.tsumapsneam.eu/), co-financed by the European Union Civil Protection Mechanism, Agreement Number: ECHO/SUB/2015/718568/PREV26.

Development of Local Amplification Factors in the NEAM Region for Production of Regional Tsunami Hazard Maps

NASA Astrophysics Data System (ADS)

Glimsdal, Sylfest; Løvholt, Finn; Bonnevie Harbitz, Carl; Orefice, Simone; Romano, Fabrizio; Brizuela, Beatriz; Lorito, Stefano; Hoechner, Andreas; Babeyko, Andrey

2017-04-01

The standard way of estimating tsunami inundation is by applying numerical depth-averaged shallow-water run-up models. However, for a regional Probabilistic Tsunami Hazard Assessment (PTHA), applying such inundation models may be too time-consuming. A faster, yet less accurate procedure, is to relate the near-shore surface elevations at offshore points to maximum shoreline water levels by using a set of amplification factors based on the characteristics of the incident wave and the bathymetric slope. The surface elevation at the shoreline then acts as a rough approximation for the maximum inundation height or run-up height along the shoreline. An amplification-factor procedure based on a limited set of idealized broken shoreline segments has previously been applied to estimate the maximum inundation heights globally. Here, we present a study where this technique is developed further, by taking into account the local bathymetric profiles. We extract a large number of local bathymetric transects over a significant part of the North East Atlantic, the Mediterranean and connected seas (NEAM region). For each bathymetric transect, we compute the wave amplification from an offshore control point to points close to the shoreline using a linear shallow-water model for waves of different period and polarity with a sinusoidal pulse wave as input. The amplification factors are then tabulated. We present maximum water levels from the amplification factor method, and compare these with results from conventional inundation models. Finally, we demonstrate how the amplification factor method can be convolved with PTHA results to provide regional tsunami hazard maps. This work has been supported by the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement 603839 (Project ASTARTE), and the TSUMAPS-NEAM Project (http://www.tsumapsneam.eu/), co-financed by the European Union Civil Protection Mechanism, Agreement Number: ECHO/SUB/2015/718568/PREV26.

Estimate Tsunami Flow Conditions and Large-Debris Tracks for the Design of Coastal Infrastructures along Coastlines of the U.S. Pacific Northwest

NASA Astrophysics Data System (ADS)

Wei, Y.; Thomas, S.; Zhou, H.; Arcas, D.; Titov, V. V.

2017-12-01

The increasing potential tsunami hazards pose great challenges for infrastructures along the coastlines of the U.S. Pacific Northwest. Tsunami impact at a coastal site is usually assessed from deterministic scenarios based on 10,000 years of geological records in the Cascadia Subduction Zone (CSZ). Aside from these deterministic methods, the new ASCE 7-16 tsunami provisions provide engineering design criteria of tsunami loads on buildings based on a probabilistic approach. This work develops a site-specific model near Newport, OR using high-resolution grids, and compute tsunami inundation depth and velocities at the study site resulted from credible probabilistic and deterministic earthquake sources in the Cascadia Subduction Zone. Three Cascadia scenarios, two deterministic scenarios, XXL1 and L1, and a 2,500-yr probabilistic scenario compliant with the new ASCE 7-16 standard, are simulated using combination of a depth-averaged shallow water model for offshore propagation and a Boussinesq-type model for onshore inundation. We speculate on the methods and procedure to obtain the 2,500-year probabilistic scenario for Newport that is compliant with the ASCE 7-16 tsunami provisions. We provide details of model results, particularly the inundation depth and flow speed for a new building, which will also be designated as a tsunami vertical evacuation shelter, at Newport, Oregon. We show that the ASCE 7-16 consistent hazards are between those obtained from deterministic L1 and XXL1 scenarios, and the greatest impact on the building may come from later waves. As a further step, we utilize the inundation model results to numerically compute tracks of large vessels in the vicinity of the building site and estimate if these vessels will impact on the building site during the extreme XXL1 and ASCE 7-16 hazard-consistent scenarios. Two-step study is carried out first to study tracks of massless particles and then large vessels with assigned mass considering drag force, inertial force, ship grounding and mooring. The simulation results show that none of the large vessels will impact on the building site in all tested scenarios.

Nuisance Flooding and Relative Sea-Level Rise: the Importance of Present-Day Land Motion.

PubMed

Karegar, Makan A; Dixon, Timothy H; Malservisi, Rocco; Kusche, Jürgen; Engelhart, Simon E

2017-09-11

Sea-level rise is beginning to cause increased inundation of many low-lying coastal areas. While most of Earth's coastal areas are at risk, areas that will be affected first are characterized by several additional factors. These include regional oceanographic and meteorological effects and/or land subsidence that cause relative sea level to rise faster than the global average. For catastrophic coastal flooding, when wind-driven storm surge inundates large areas, the relative contribution of sea-level rise to the frequency of these events is difficult to evaluate. For small scale "nuisance flooding," often associated with high tides, recent increases in frequency are more clearly linked to sea-level rise and global warming. While both types of flooding are likely to increase in the future, only nuisance flooding is an early indicator of areas that will eventually experience increased catastrophic flooding and land loss. Here we assess the frequency and location of nuisance flooding along the eastern seaboard of North America. We show that vertical land motion induced by recent anthropogenic activity and glacial isostatic adjustment are contributing factors for increased nuisance flooding. Our results have implications for flood susceptibility, forecasting and mitigation, including management of groundwater extraction from coastal aquifers.

Numerical Analysis of Flood modeling of upper Citarum River under Extreme Flood Condition

NASA Astrophysics Data System (ADS)

Siregar, R. I.

2018-02-01

This paper focuses on how to approach the numerical method and computation to analyse flood parameters. Water level and flood discharge are the flood parameters solved by numerical methods approach. Numerical method performed on this paper for unsteady flow conditions have strengths and weaknesses, among others easily applied to the following cases in which the boundary irregular flow. The study area is in upper Citarum Watershed, Bandung, West Java. This paper uses computation approach with Force2 programming and HEC-RAS to solve the flow problem in upper Citarum River, to investigate and forecast extreme flood condition. Numerical analysis based on extreme flood events that have occurred in the upper Citarum watershed. The result of water level parameter modeling and extreme flood discharge compared with measurement data to analyse validation. The inundation area about flood that happened in 2010 is about 75.26 square kilometres. Comparing two-method show that the FEM analysis with Force2 programs has the best approach to validation data with Nash Index is 0.84 and HEC-RAS that is 0.76 for water level. For discharge data Nash Index obtained the result analysis use Force2 is 0.80 and with use HEC-RAS is 0.79.

The Big Splash: Tsunami from Large Asteroid and Comet Impacts

NASA Astrophysics Data System (ADS)

Hills, J.; Goda, M.

Asteroid and comet impacts produce a large range of damage. Tsunami may produce most of the economic damage in large asteroid impacts. Large asteroid impacts produce worldwide darkness lasting several months that may kill more people by mass starvation, especially in developing countries, than would tsunami, but the dust should not severely affect economic infrastructure. The tsunami may even kill more people in developed countries with large coastal populations, such as the United States, than the starvation resulting from darkness. We have been determining which regions of Earth are most susceptible to asteroid tsunami by simulating the effect of a large asteroid impact into mid-ocean. We have modeled the effect of midAtlantic and midPacific impacts that produce craters 300 to 150 km in diameter. A KT-size impactor would cause the larger of these craters. We used a computer code that has successfully determined the runup and inundation from historical earthquake-generated tsunami. The code has been progressively improved to eliminate previous problems at the domain boundaries, so it now runs until the tsunami inundation is complete. We find that the larger of these two midAtlantic impacts would engulf the entire Florida Peninsula. The smaller one would inundate the eastern third of the peninsula while a tsunami passing through the Gulf of Cuba would inundate the West Coast of Florida. Impacts at three different sites in the Pacific show the great vulnerability of Tokyo and its surroundings to asteroid tsunami. Mainland Asia is relatively protected from asteroid tsunami. In Europe, the Iberian Peninsula and the Atlantic Providences of France are highly vulnerable to asteroid tsunami.

Quantifying the importance of spatial resolution and other factors through global sensitivity analysis of a flood inundation model

NASA Astrophysics Data System (ADS)

Thomas Steven Savage, James; Pianosi, Francesca; Bates, Paul; Freer, Jim; Wagener, Thorsten

2016-11-01

Where high-resolution topographic data are available, modelers are faced with the decision of whether it is better to spend computational resource on resolving topography at finer resolutions or on running more simulations to account for various uncertain input factors (e.g., model parameters). In this paper we apply global sensitivity analysis to explore how influential the choice of spatial resolution is when compared to uncertainties in the Manning's friction coefficient parameters, the inflow hydrograph, and those stemming from the coarsening of topographic data used to produce Digital Elevation Models (DEMs). We apply the hydraulic model LISFLOOD-FP to produce several temporally and spatially variable model outputs that represent different aspects of flood inundation processes, including flood extent, water depth, and time of inundation. We find that the most influential input factor for flood extent predictions changes during the flood event, starting with the inflow hydrograph during the rising limb before switching to the channel friction parameter during peak flood inundation, and finally to the floodplain friction parameter during the drying phase of the flood event. Spatial resolution and uncertainty introduced by resampling topographic data to coarser resolutions are much more important for water depth predictions, which are also sensitive to different input factors spatially and temporally. Our findings indicate that the sensitivity of LISFLOOD-FP predictions is more complex than previously thought. Consequently, the input factors that modelers should prioritize will differ depending on the model output assessed, and the location and time of when and where this output is most relevant.

Tsunami-induced boulder transport - combining physical experiments and numerical modelling

NASA Astrophysics Data System (ADS)

Oetjen, Jan; Engel, Max; May, Simon Matthias; Schüttrumpf, Holger; Brueckner, Helmut; Prasad Pudasaini, Shiva

2016-04-01

Coasts are crucial areas for living, economy, recreation, transportation, and various sectors of industry. Many of them are exposed to high-energy wave events. With regard to the ongoing population growth in low-elevation coastal areas, the urgent need for developing suitable management measures, especially for hazards like tsunamis, becomes obvious. These measures require supporting tools which allow an exact estimation of impact parameters like inundation height, inundation area, and wave energy. Focussing on tsunamis, geological archives can provide essential information on frequency and magnitude on a longer time scale in order to support coastal hazard management. While fine-grained deposits may quickly be altered after deposition, multi-ton coarse clasts (boulders) may represent an information source on past tsunami events with a much higher preservation potential. Applying numerical hydrodynamic coupled boulder transport models (BTM) is a commonly used approach to analyse characteristics (e.g. wave height, flow velocity) of the corresponding tsunami. Correct computations of tsunamis and the induced boulder transport can provide essential event-specific information, including wave heights, runup and direction. Although several valuable numerical models for tsunami-induced boulder transport exist (e. g. Goto et al., 2007; Imamura et al., 2008), some important basic aspects of both tsunami hydrodynamics and corresponding boulder transport have not yet been entirely understood. Therefore, our project aims at these questions in four crucial aspects of boulder transport by a tsunami: (i) influence of sediment load, (ii) influence of complex boulder shapes other than idealized rectangular shapes, (iii) momentum transfers between multiple boulders, and (iv) influence of non-uniform bathymetries and topographies both on tsunami and boulder. The investigation of these aspects in physical experiments and the correct implementation of an advanced model is an urgent need since they have been largely neglected. In order to tackle these gaps, we develop a novel BTM in two steps. First, scaled physical experiments are performed that determine the exact hydrodynamic processes within a tsunami during boulder transportations. Furthermore, the experiments are the basis for calibrating the numerical BTM. The BTM is based on the numerical two-phase mass flow model of Pudasaini (2012) that employs an advanced and unified high-resolution computational tool for mixtures consisting of the solid and fluid components and their interactions. This allows for the motion of the boulder while interacting with the particle-laden tsunami on the inundated coastal plane as a function of the total fluid and solid stresses. Our approach leads to fundamentally new insights in to the essential physical processes in BTM. Goto, K., Chavanich, S. A., Imamura, F., Kunthasap, P., Matsui, T., Minoura, K., Sugawara, D. and Yanagisawa, H.: Distribution, origin and transport process of boulders deposited by the 2004 Indian Ocean tsunami at Pakarang Cape, Thailand. Sediment. Geol., 202, 821-837, 2007. Imamura, F., Goto, K. and Ohkubo, S.: A numerical model of the transport of a boulder by tsunami. J. Geophys. Res. Oceans, 113, C01008, 2008. Pudasaini, S. P.: A general two-phase debris flow model. J. Geophys. Res. Earth Surf., 117, F03010, 2012.

Lahar hazard zones for eruption-generated lahars in the Lassen Volcanic Center, California

USGS Publications Warehouse

Robinson, Joel E.; Clynne, Michael A.

2012-01-01

Lahar deposits are found in drainages that head on or near Lassen Peak in northern California, demonstrating that these valleys are susceptible to future lahars. In general, lahars are uncommon in the Lassen region. Lassen Peak's lack of large perennial snowfields and glaciers limits its potential for lahar development, with the winter snowpack being the largest source of water for lahar generation. The most extensive lahar deposits are related to the May 1915 eruption of Lassen Peak, and evidence for pre-1915 lahars is sparse and spatially limited. The May 1915 eruption of Lassen Peak was a small-volume eruption that generated a snow and hot-rock avalanche, a pyroclastic flow, and two large and four smaller lahars. The two large lahars were generated on May 19 and 22 and inundated sections of Lost and Hat Creeks. We use 80 years of snow depth measurements from Lassen Peak to calculate average and maximum liquid water depths, 2.02 meters (m) and 3.90 m respectively, for the month of May as estimates of the 1915 lahars. These depths are multiplied by the areal extents of the eruptive deposits to calculate a water volume range, 7.05-13.6x106 cubic meters (m3). We assume the lahars were a 50/50 mix of water and sediment and double the water volumes to provide an estimate of the 1915 lahars, 13.2-19.8x106 m3. We use a representative volume of 15x106 m3 in the software program LAHARZ to calculate cross-sectional and planimetric areas for the 1915 lahars. The resultant lahar inundation zone reasonably portrays both of the May 1915 lahars. We use this same technique to calculate the potential for future lahars in basins that head on or near Lassen Peak. LAHARZ assumes that the total lahar volume does not change after leaving the potential energy, H/L, cone (the height of the edifice, H, down to the approximate break in slope at its base, L); therefore, all water available to initiate a lahar is contained inside this cone. Because snow is the primary source of water for lahar generation, we assume that the maximum historical water equivalent, 3.90 m, covers the entire basin area inside the H/L cone. The product of planimetric area of each basin inside the H/L and the maximum historical water equivalent yields the maximum water volume available to generate a lahar. We then double the water volumes to approximate maximum lahar volumes. The maximum lahar volumes and an understanding of the statistical uncertainties inherent to the LAHARZ calculations guided our selection of six hypothetical volumes, 1, 3, 10, 30, 60, and 90x106 m3, to delineate concentric lahar inundation zones. The lahar inundation zones extend, in general, tens of kilometers away from Lassen Peak. The small, more-frequent lahar inundation zones (1 and 3x106 m3) are, on average, 10 km long. The exceptions are the zones in Warner Creek and Mill Creek, which extend much further. All but one of the small, more-frequent lahar inundation zones reach outside of the Lassen Volcanic National Park boundary, and the zone in Mill Creek extends well past the park boundary. All of the medium, moderately frequent lahar inundation zones (10 and 30x106 m3) extend past the park boundary and could potentially impact the communities of Viola and Old Station and State Highways 36 and 44, both north and west of Lassen Peak. The approximately 27-km-long on average, large, less-frequent lahar inundation zones (60 and 90x106 m3) represent worst-case lahar scenarios that are unlikely to occur. Flood hazards continue downstream from the toes of the lahars, potentially affecting communities in the Sacramento River Valley.

Boreal Inundation Mapping with SMAP Radiometer Data for Methane Studies

NASA Astrophysics Data System (ADS)

Kim, Seungbum; Brisco, Brian; Poncos, Valentin

2017-04-01

Inundation and consequent anoxic condition induce methane release, which is one of the most potent greenhouse gases. Boreal regions contain large amounts of organic carbon, which is a potentially major methane emission source under climatic warming conditions. Boreal wetlands in particular are one of the largest sources of uncertainties in global methane budget. Wetland spatial extent together with the gas release rate remains highly unknown. Characterization of the existing inundation database is poor, because of the inundation under clouds and dense vegetation. In this work, the inundation extent is derived using brightness temperature data acquired by the L-band Soil Moisture Active Passive (SMAP) satellite, which offers the L-band capabilities to penetrate clouds and vegetation at 3-day revisit. The fidelity of the SMAP watermask is assessed as a first step in this investigation by comparing with the following data sets: 3-m resolution maps derived using Radarsat synthetic aperture radar (SAR) data in northern Canada and multi-sensor climatology over Siberia. Because Radarsat coverages are limited despite its high spatial resolution, at the time and location where Radarsats are not available, we also compare with 3-km resolution SMAP SAR data that are concurrent with the SMAP radiometer data globally until July 2015. Inundation extents were derived with Radarsat, SMAP SAR, and SMAP radiometer over the 60 km x 60km area at Peace Athabasca Delta (PAD), Canada on 6 days in spring and summer 2015. The SMAP SAR results match the locations of Radarsat waterbodies. However, the SMAP SAR underestimates the water extent, mainly over mixed pixels that have subpixel land presence. The threshold value (-3 dB) applied to the SMAP SAR was determined previously over the global domain. The threshold is dependent on the type of local landcover within a mixed pixel. Further analysis is needed to locally optimize the threshold. The SMAP radiometer water fraction over Peace Athabasca Delta varies from 0% to 25% spatially, which corresponds well with the waterbodies identified by Radarsat. To quantify the agreement, the SMAP radiometer data will be resampled to center itself within the study domain in the future. West Siberia is one of the areas of significant methane exchance but the current estimates of the exchange differ by several times depending on the methodology. The radiometer-based SMAP water extent shows the consistent seasonality compared with the climatology (Global Inundation Extent from Multi-Satellites, GIEMS). SMAP's water extent appears more realistic in winter than shown by GIEMS: even in winter there are unfrozen wetlands identified by SMAP, which is plausible considering that the southern boundary of West Siberia is at 50°N. The watermask produced with the global SMAP radiometer data will be applied to the bottom-up numerical model for methane release run at Purdue university, to experiment its impact on methane exchange.

Understanding the Hydrodynamics of a Coastal Wetland with an Integrated Distributed Model

NASA Astrophysics Data System (ADS)

Zhang, Y.; Li, W.; Sun, G.

2017-12-01

Coastal wetlands linking ocean and terrestrial landscape provide important ecosystem services including flood mitigation, fresh water supply, erosion control, carbon sequestration, and wildlife habitats. Wetland hydrology is the major driving force for wetland formation, structure, function, and ecosystem services. The dynamics of wetland hydrology and energy budget are strongly affected by frequent inundation and drying of wetland soil and vegetation due to tide, sea level rise (SLR) and climatic variability (change). However, the quantitative representation of how the energy budget and groundwater variation of coastal wetlands respond to frequent water level fluctuation is limited, especially at regional scales. This study developed a physically based distributed wetland hydrological model by integrating coastal processes and considering the inundation influence on energy budget and ET. Analysis using in situ measurements and satellite data for a coastal wetland in North Carolina confirm that the model sufficiently captures the wetland hydrologic behaviors. The validated model was then applied to examine the wetland hydrodynamics under a 30-year historical climate forcing (1985-2014) for the wetland region. The simulation reveals that 43% of the study area has inundation events, 63% of which has a frequency higher than 50% each year. The canopy evaporation and transpiration decline dramatically when the inundation level exceeds the canopy height. Additionally, inundation causes about 10% increase of the net shortwave radiation. This study also demonstrates that the critical wetland zones highly influenced by the coastal processes spans 300-800 m from the coastline. The model developed in the study offers a new tool for understanding the complex wetland hydrodynamics in response to natural and human-induced disturbances at landscape to regional scales.

[Characteristics of dissolved organic carbon release under inundation from typical grass plants in the water-level fluctuation zone of the Three Gorges Reservoir area].

PubMed

Tan, Qiu-Xia; Zhu, Boi; Hua, Ke-Ke

2013-08-01

The water-level fluctuation zone of the Three Gorges Reservoir (TGR) exposes in spring and summer, then, green plants especially herbaceous plants grow vigorously. In the late of September, water-level fluctuation zone of TGR goes to inundation. Meanwhile, annually accumulated biomass of plant will be submerged for decaying, resulting in organism decomposition and release a large amount of dissolved organic carbon (DOC). This may lead to negative impacts on water environment of TGR. The typical herbaceous plants from water-level fluctuation zone were collected and inundated in the laboratory for dynamic measurements of DOC concentration of overlying water. According to the determination, the DOC release rates and fluxes have been calculated. Results showed that the release process of DOC variation fitted in a parabolic curve. The peak DOC concentrations emerge averagely in the 15th day of inundation, indicating that DOC released quickly with organism decay of herbaceous plant. The release process of DOC could be described by the logarithm equation. There are significant differences between the concentration of DOC (the maximum DOC concentration is 486.88 mg x L(-1) +/- 35.97 mg x L(-1) for Centaurea picris, the minimum is 4.18 mg x L(-1) +/- 1.07 mg x L(-1) for Echinochloacrus galli) and the release amount of DOC (the maximum is 50.54 mg x g(-1) for Centaurea picris, the minimum is 6.51 mg x g(-1) for Polygonum hydropiper) due to different characteristics of plants, especially, the values of C/N of herbaceous plants. The cumulative DOC release quantities during the whole inundation period were significantly correlated with plants' C/N values in linear equations.

Chesapeake Inundation Prediction System (CIPS): A regional prototype for a national problem

USGS Publications Warehouse

Stamey, B.; Smith, W.; Carey, K.; Garbin, D.; Klein, F.; Wang, Hongfang; Shen, J.; Gong, W.; Cho, J.; Forrest, D.; Friedrichs, C.; Boicourt, W.; Li, M.; Koterba, M.; King, D.; Titlow, J.; Smith, E.; Siebers, A.; Billet, J.; Lee, J.; Manning, Douglas R.; Szatkowski, G.; Wilson, D.; Ahnert, P.; Ostrowski, J.

2007-01-01

Recent Hurricanes Katrina and Isabel, among others, not only demonstrated their immense destructive power, but also revealed the obvious, crucial need for improved storm surge forecasting and information delivery to save lives and property in future storms. Current operational methods and the storm surge and inundation products do not adequately meet requirements needed by Emergency Managers (EMs) at local, state, and federal levels to protect and inform our citizens. The Chesapeake Bay Inundation Prediction System (CIPS) is being developed to improve the accuracy, reliability, and capability of flooding forecasts for tropical cyclones and non-tropical wind systems such as nor'easters by modeling and visualizing expected on-land storm-surge inundation along the Chesapeake Bay and its tributaries. An initial prototype has been developed by a team of government, academic and industry partners through the Chesapeake Bay Observing System (CBOS) of the Mid-Atlantic Coastal Ocean Observing Regional Association (MACOORA) within the Integrated Ocean Observing System (IOOS). For demonstration purposes, this initial prototype was developed for the tidal Potomac River in the Washington, DC metropolitan area. The preliminary information from this prototype shows great potential as a mechanism by which NOAA National Weather Service (NWS) Forecast Offices (WFOs) can provide more specific and timely forecasts of likely inundation in individual localities from significant storm surge events. This prototype system has shown the potential to indicate flooding at the street level, at time intervals of an hour or less, and with vertical resolution of one foot or less. This information will significantly improve the ability of EMs and first responders to mitigate life and property loss and improve evacuation capabilities in individual communities. This paper provides an update and expansion of the initial prototype that was presented at the Oceans 2006 MTS/IEEE Conference in Boston, MA. ??2007 MTS.

Movement patterns of riparian small mammals during predictable floodplain inundation

USGS Publications Warehouse

Andersen, D.C.; Wilson, K.R.; Miller, M.S.; Falck, M.

2000-01-01

We monitored movements of small mammals resident on floodplains susceptible to spring floods to assess whether and how these animals respond to habitat inundation. The 2 floodplains were associated with 6th order river segments in a semiarid landscape; each was predictably inundated each year as snowmelt progressed in headwater areas of the Rocky Mountains. Data from live trapping, radiotelemetry, and microtopographic surveys indicated that Peromyscus maniculatus, Microtus montanus, and Dipodomys ordii showed different responses to inundation, but all reflected a common tendency to remain in the original home range until “forced” to leave. The reluctance of Dipodomys ordii to abandon the home burrow often resulted in death in situ, whereas individual P. maniculatus and M. montanus moved to nearby higher ground but not necessarily toward upland. This behavior could lead to occupancy of an island that disappeared as floodwaters rose. Peromyscus maniculatus climbed into sapling cottonwood, but the quality of such arboreal refuges was unclear. We found only weak support for the hypothesis that displacement was temporary; most floodplain residents, including P. maniculatus, disappeared over the flood period. No secondary effect from flooding on adjacent upland small-mammal assemblages was detected. Our data suggest populations of facultatively riparian, nonarboreal small mammals such as M. montanus and D. ordii generally experience habitat inundation as a catastrophy. Terrestrial species capable of using an arboreal refuge, such as P. maniculatus, face a more variable risk, determined in part by timing and duration of the flood event. River regulation can affect both sets of risks.

A Cultural Assessment of the Archeological Resources in the Keystone Lake Project Area, North-Central Oklahoma.

DTIC Science & Technology

1980-01-01

CHAPTER 1. INTRODUCTION...... ....... . . . .. .. .... by Bruce M. Moore PART I. BACKGROUND CHAPTER 2. ENVIRONMENTAL SETTING...Area Inundation Impacts .. .. .... 235 Environmental Matrices Variable. .. .. . . ..... 236 Reservoir Dynamics Variable. .. ... .. ...... 236rCultural...susceptibility to erosional processes. PART I. BACKGROUND a- I CHAPTER 2 ENVIRONMENTAL SETTING Keystone Lake was formed by impounding the Arkansas and Cimarron

Inundation, sedimentation, and subsidence creates goose habitat along the Arctic coast of Alaska

USGS Publications Warehouse

Tape, Ken D.; Flint, Paul L.; Meixell, Brandt W.; Gaglioti, Benjamin V.

2013-01-01

The Arctic Coastal Plain of Alaska is characterized by thermokarst lakes and drained lake basins, and the rate of coastal erosion has increased during the last half-century. Portions of the coast are <1 m above sea level for kilometers inland, and are underlain by ice-rich permafrost. Increased storm surges or terrestrial subsidence would therefore expand the area subject to marine inundation. Since 1976, the distribution of molting Black Brant (Branta bernicla nigricans) on the Arctic Coastal Plain has shifted from inland freshwater lakes to coastal marshes, such as those occupying the Smith River and Garry Creek estuaries. We hypothesized that the movement of geese from inland lakes was caused by an expansion of high quality goose forage in coastal areas. We examined the recent history of vegetation and geomorphological changes in coastal goose habitat by combining analysis of time series imagery between 1948 and 2010 with soil stratigraphy dated using bomb-curve radiocarbon. Time series of vertical imagery and in situ verification showed permafrost thaw and subsidence of polygonal tundra. Soil stratigraphy and dating within coastal estuaries showed that non-saline vegetation communities were buried by multiple sedimentation episodes between 1948 and 1995, accompanying a shift toward salt-tolerant vegetation. This sedimentation allowed high quality goose forage plants to expand, thus facilitating the shift in goose distribution. Declining sea ice and the increasing rate of terrestrial inundation, sedimentation, and subsidence in coastal estuaries of Alaska may portend a 'tipping point' whereby inland areas would be transformed into salt marshes.

Tsunami Waves Joint Inversion Using Tsunami Inundation, Tsunami Deposits Distribution and Marine-Terrestrial Sediment Signal in Tsunami Deposit

NASA Astrophysics Data System (ADS)

Tang, H.; WANG, J.

2017-12-01

Population living close to coastlines is increasing, which creates higher risks due to coastal hazards, such as the tsunami. However, the generation of a tsunami is not fully understood yet, especially for paleo-tsunami. Tsunami deposits are one of the concrete evidence in the geological record which we can apply for studying paleo-tsunami. The understanding of tsunami deposits has significantly improved over the last decades. There are many inversion models (e.g. TsuSedMod, TSUFLIND, and TSUFLIND-EnKF) to study the overland-flow characteristics based on tsunami deposits. However, none of them tries to reconstruct offshore tsunami wave characteristics (wave form, wave height, and length) based on tsunami deposits. Here we present a state-of-the-art inverse approach to reconstruct offshore tsunami wave based on the tsunami inundation data, the spatial distribution of tsunami deposits and Marine-terrestrial sediment signal in the tsunami deposits. Ensemble Kalman Filter (EnKF) Method is used for assimilating both sediment transport simulations and the field observation data. While more computationally expensive, the EnKF approach potentially provides more accurate reconstructions for tsunami waveform. In addition to the improvement of inversion results, the ensemble-based method can also quantify the uncertainties of the results. Meanwhile, joint inversion improves the resolution of tsunami waves compared with inversions using any single data type. The method will be tested by field survey data and gauge data from the 2011 Tohoku tsunami on Sendai plain area.

New Tsunami Inundation Maps for California

NASA Astrophysics Data System (ADS)

Barberopoulou, Aggeliki; Borrero, Jose; Uslu, Burak; Kanoglu, Utku; Synolakis, Costas

2010-05-01

California is the first US State to complete its tsunami inundation mapping. A new generation of tsunami inundation maps is now available for 17 coastal counties.. The new maps offer improved coverage for many areas, they are based on the most recent descriptions of potential tsunami farfield and nearfield sources and use the best available bathymetric and topographic data for modelling. The need for new tsunami maps for California became clear since Synolakis et al (1998) described how inundation projections derived with inundation models that fully calculate the wave evolution over dry land can be as high as twice the values predicted with earlier threshold models, for tsunamis originating from tectonic source. Since the 1998 Papua New Guinea tsunami when the hazard from offshore submarine landslides was better understood (Bardet et al, 2003), the State of California funded the development of the first generation of maps, based on local tectonic and landslide sources. Most of the hazard was dominated by offshore landslides, whose return period remains unknown but is believed to be higher than 1000 years for any given locale, at least in Southern California. The new generation of maps incorporates local and distant scenarios. The partnership between the Tsunami Research Center at USC, the California Emergency Management Agency and the California Seismic Safety Commission let the State to be the first among all US States to complete the maps. (Exceptions include the offshore islands and Newport Beach, where higher resolution maps are under way). The maps were produced with the lowest cost per mile of coastline, per resident or per map than all other States, because of the seamless integration of the USC and NOAA databases and the use of the MOST model. They are a significant improvement over earlier map generations. As part of a continuous improvement in response, mitigation and planning and community education, the California inundation maps can contribute in reducing tsunami risk. References -Bardet, JP et al (2003), Landslide tsunamis: Recent findings and research directions, Pure and Applied Geophysics, 160, (10-11), 1793-1809. -Eisner, R., Borrero, C., Synolakis, C.E. (2001) Inundation Maps for the State of California, International Tsunami Symposium, ITS 2001 Proceedings, NHTMP Review Paper #4, 67-81. -Synolakis, C.E., D. McCarthy, V.V. Titov, J.C. Borrero, (1998) Evaluating the Tsunami Risk in California, CALIFORNIA AND THE WORLD OCEAN '97, 1225-1236, Proceedings ASCE, ISBN: 0-7844-0297-3.

Two-dimensional simulation of the June 11, 2010, flood of the Little Missouri River at Albert Pike Recreational Area, Ouachita National Forest, Arkansas

USGS Publications Warehouse

Wagner, Daniel M.

2013-01-01

In the early morning hours of June 11, 2010, substantial flooding occurred at Albert Pike Recreation Area in the Ouachita National Forest of west-central Arkansas, killing 20 campers. The U.S. Forest Service needed information concerning the extent and depth of flood inundation, the water velocity, and flow paths throughout Albert Pike Recreation Area for the flood and for streamflows corresponding to annual exceedence probabilities of 1 and 2 percent. The two-dimensional flow model Fst2DH, part of the Federal Highway Administration’s Finite Element Surface-water Modeling System, and the graphical user interface Surface-water Modeling System (SMS) were used to perform a steady-state simulation of the flood in a 1.5-mile reach of the Little Missouri River at Albert Pike Recreation Area. Peak streamflows of the Little Missouri River and tributary Brier Creek served as inputs to the simulation, which was calibrated to the surveyed elevations of high-water marks left by the flood and then used to predict flooding that would result from streamflows corresponding to annual exceedence probabilities of 1 and 2 percent. The simulated extent of the June 11, 2010, flood matched the observed extent of flooding at Albert Pike Recreation Area. The mean depth of inundation in the camp areas was 8.5 feet in Area D, 7.4 feet in Area C, 3.8 feet in Areas A, B, and the Day Use Area, and 12.5 feet in Lowry’s Camp Albert Pike. The mean water velocity was 7.2 feet per second in Area D, 7.6 feet per second in Area C, 7.2 feet per second in Areas A, B, and the Day Use Area, and 7.6 feet per second in Lowry’s Camp Albert Pike. A sensitivity analysis indicated that varying the streamflow of the Little Missouri River had the greatest effect on simulated water-surface elevation, while varying the streamflow of tributary Brier Creek had the least effect. Simulated water-surface elevations were lower than those modeled by the U.S. Forest Service using the standard-step method, but the comparison between the two was favorable with a mean absolute difference of 0.58 feet in Area C and 0.32 feet in Area D. Results of a HEC-RAS model of the Little Missouri River watershed upstream from the U.S. Geological Survey streamflow-gaging station near Langley showed no difference in mean depth in the areas in common between the models, and a difference in mean velocity of only 0.5 foot per second. Predictions of flooding that would result from streamflows corresponding to annual exceedence probabilities of 1 and 2 percent indicated that the extent of inundation of the June 11, 2010, flood exceeded that of the 1 percent flood, and that for both the 1 and 2 percent floods, all of Areas C and D, and parts of Areas A, B, and the Day Use Area were inundated. Predicted water-surface elevations for the 1 and 2 percent floods were approximately 1 foot lower than those predicted by the U.S. Forest Service using a standard-step model.

Wetlands: Earth's Kidneys

EPA Science Inventory

Wetlands are unique, diverse, and productive habitats that emerge at the fringe of aquatic and upland land systems. The U.S. Environmental Protection Agency (EPA) defines wetlands as "areas that are regularly inundated by surface water or groundwater and characterized by a preva...

Depressional wetlands affect watershed hydrological, biogeochemical, and ecological functions.

PubMed

Evenson, Grey R; Golden, Heather E; Lane, Charles R; McLaughlin, Daniel L; D'Amico, Ellen

2018-06-01

Depressional wetlands of the extensive U.S. and Canadian Prairie Pothole Region afford numerous ecosystem processes that maintain healthy watershed functioning. However, these wetlands have been lost at a prodigious rate over past decades due to drainage for development, climate effects, and other causes. Options for management entities to protect the existing wetlands, and their functions, may focus on conserving wetlands based on spatial location vis-à-vis a floodplain or on size limitations (e.g., permitting smaller wetlands to be destroyed but not larger wetlands). Yet the effects of such management practices and the concomitant loss of depressional wetlands on watershed-scale hydrological, biogeochemical, and ecological functions are largely unknown. Using a hydrological model, we analyzed how different loss scenarios by wetland size and proximal location to the stream network affected watershed storage (i.e., inundation patterns and residence times), connectivity (i.e., streamflow contributing areas), and export (i.e., streamflow) in a large watershed in the Prairie Pothole Region of North Dakota, USA. Depressional wetlands store consequential amounts of precipitation and snowmelt. The loss of smaller depressional wetlands (<3.0 ha) substantially decreased landscape-scale inundation heterogeneity, total inundated area, and hydrological residence times. Larger wetlands act as hydrologic "gatekeepers," preventing surface runoff from reaching the stream network, and their modeled loss had a greater effect on streamflow due to changes in watershed connectivity and storage characteristics of larger wetlands. The wetland management scenario based on stream proximity (i.e., protecting wetlands 30 m and ~450 m from the stream) alone resulted in considerable landscape heterogeneity loss and decreased inundated area and residence times. With more snowmelt and precipitation available for runoff with wetland losses, contributing area increased across all loss scenarios. We additionally found that depressional wetlands attenuated peak flows; the probability of increased downstream flooding from wetland loss was also consistent across all loss scenarios. It is evident from this study that optimizing wetland management for one end goal (e.g., protection of large depressional wetlands for flood attenuation) over another (e.g., protecting of small depressional wetlands for biodiversity) may come at a cost for overall watershed hydrological, biogeochemical, and ecological resilience, functioning, and integrity. © 2018 by the Ecological Society of America.

Flood risk assessment through 1D/2D couple HEC-RAS hydrodynamic modeling- A case study of Surat City, Lower Tapi Basin, India

NASA Astrophysics Data System (ADS)

Patel, Dhruvesh; Ramirez, Jorge; Srivastava, Prashant; Bray, Michaela; Han, Dawei

2017-04-01

Surat, known as the diamond city of Gujart is situated 100 km downstream of Ukai dam and near the mouth of river Tapi and affected by the flood at every alternate year. The city experienced catastrophic floods in 1933, 1959, 1968, 1970, 1994, 1998 and 2006. It is estimated that a single flood event during August 6-12, 2006 in Surat and Hazira twin-city, caused heavy damages, resulted in the death of 300 people and property damage worth € 289 million. The peak discharge of 25768 m3 s-1 release from Ukai dam was responsible for the disastrous flood in Surat city. To identifylow lying areas prone to inundation and reduce the uncertainty in flood mitigation measures, HEC-RAS based 1D/2D Couple hydrodynamic modeling is carried out for Surat city. Release from the Ukai dam and tidal level of the sea are considered for upstream and downstream boundary condition. 299 surveyed cross-sections have been considered for 1D modeling, whereas a topographic map at 0.5 m contour interval was used to produce a 5 m grid and SRTM (30 & 90 m) grid has been considered for Suart and Lower Tapi Basin (LTB). Flow is simulated under unsteady conditions, calibrated for the year 1998 and validated for the year 2006. The simulated result shows that the 9th August 18.00 hr was the worst day for Surat city and maximum 75-77 % area was under inundation. Most of the flooded area experienced 0.25 m/s water velocity with the duration of 90 hr. Due to low velocity and high duration of the flood, a low lying area within the west zone and south-west zone of the city was badly affected by the flood, whereas the south zone and south-east zone was least. Simulated results show good correlation when compared with an observed flood level map. The simulated results will be helpful to improve the flood resilience strategy at Surat city and reduce the uncertainty for flood inundation mapping for future dam releases. The present case study shows the applicability of 1D/2D coupled hydrodynamic modeling for flood inundation mapping and can be applied for flood assessment at locations with similar geographical conditions.

Impacts of land cover changes on hurricane storm surge in the lower Chesapeake Bay

NASA Astrophysics Data System (ADS)

Denton, M.; Lawler, S.; Ferreira, C.

2013-12-01

The Chesapeake Bay is the largest estuary in the United States with more than 150 rivers draining into the bay's tidal wetlands. Coastal wetlands and vegetation play an important role in shaping the hydrodynamics of storm surge events by retaining water and slowing the propagation of storm surge. In this way coastal wetlands act as a natural barrier to inland flooding, particularly against less intense storms. Threats to wetlands come from both land development (residential or commercial/industrial) and sea level rise. The lower region of the Chesapeake Bay near its outlet is especially vulnerable to flooding from Atlantic storm surge brought in by hurricanes, tropical storms and nor'easters (e.g., hurricanes Isabel [2003] and Sandy [2012]). This region is also intensely developed with nearly 1.7 million residents within the greater Hampton Roads metropolitan area. Anthropogenic changes to land cover in the lower bay can directly impact basin drainage and storm surge propagation with impacts reaching beyond the immediate coastal zone to affect flooding in inland areas. While construction of seawall barriers around population centers may provide storm surge protection to a specifically defined area, these barriers deflect storm surge rather than attenuate it, underscoring the importance of wetlands. To analyze these impacts a framework was developed combining numerical simulations with a detailed hydrodynamic characterization of flow through coastal wetland areas. Storm surges were calculated using a hydrodynamic model (ADCIRC) coupled to a wave model (SWAN) forced by an asymmetric hurricane vortex model using the FEMA region 3 unstructured mesh (2.3 million nodes) under a High Performance Computing (HPC) environment. Multiple model simulations were performed using historical hurricanes data and hypothetical storms to compare the predicted storm surge inundation with various levels of wetland reduction and/or beach hardening. These data were combined and overlaid with a geospatial inventory of critical infrastructure assets to evaluate the potential for storm damage associated with each level of wetland reduction. This poster will present quantitative analyses of the benefits and losses regarding storm surge inundation and damage from land cover changes in the study region.

Hydrologic, soil, and vegetation gradients in remnant and constructed riparian wetlands in west-central Missouri, 2001-04

USGS Publications Warehouse

Heimann, David C.; Mettler-Cherry, Paige A.

2004-01-01

A study was conducted by the U.S. Geological Survey in cooperation with the Missouri Department of Conservation at the Four Rivers Conservation Area (west-central Missouri), between January 2001 and March 2004, to examine the relations between environmental factors (hydrology, soils, elevation, and landform type) and the spatial distribution of vegetation in remnant and constructed riparian wetlands. Vegetation characterization included species composition of ground, understory, and overstory layers in selected landforms of a remnant bottomland hardwood ecosystem, monitoring survival and growth of reforestation plots in leveed and partially leveed constructed wetlands, and determining gradients in colonization of herbaceous vegetation in a constructed wetland. Similar environmental factors accounted for variation in the distribution of ground, understory, and overstory vegetation in the remnant bottomland forest plots. The primary measured determining factors in the distribution of vegetation in the ground layer were elevation, soil texture (clay and silt content), flooding inundation duration, and ponding duration, while the distribution of vegetation in the understory layer was described by elevation, soil texture (clay, silt, and sand content), total flooding and ponding inundation duration, and distance from the Marmaton or Little Osage River. The primary measured determining factors in the distribution of overstory vegetation in Unit 1 were elevation, soil texture (clay, silt, and sand content), total flooding and ponding inundation duration, ponding duration, and to some extent, flooding inundation duration. Overall, the composition and structure of the remnant bottomland forest is indicative of a healthy, relatively undisturbed flood plain forest. Dominant species have a distribution of individuals that shows regeneration of these species with significant recruitment in the smaller size classes. The bottomland forest is an area whose overall hydrology has not been significantly altered; however, portions of the area have suffered from hydrologic alteration by a drainage ditch that is resulting in the displacement of swamp and marsh species by colonizing shrub and tree species. This area likely will continue to develop into an immature flood plain forest under the current (2004) hydrologic regime. Reforestation plots in constructed wetlands consisted of sampling survival and growth of multiple tree species (Quercus palustris, pin oak; Carya illinoiensis, pecan) established under several production methods and planted at multiple elevations. Comparison of survival between tree species and production types showed no significant differences for all comparisons. Survival was high for both species and all production types, with the highest mortality seen in the mounded root production method (RPM?) Quercus palustris (pin oak, 6.9 percent), while direct seeded Quercus palustris at middle elevation and bare root Quercus palustris seedlings at the low elevation plots had 100 percent survival. Measures of growth (diameter and height) were assessed among species, production types, and elevation by analyzing relative growth. The greatest rate of tree diameter (72.3 percent) and height (65.3 percent) growth was observed for direct seeded Quercus palustris trees planted at a middle elevation site. Natural colonized vegetation data were collected at multiple elevations within an abandoned cropland area of a constructed wetland. The primary measured determining factors in the distribution of herbaceous vegetation in this area were elevation, ponding duration, and soil texture. Richness, evenness, and diversity were all significantly greater in the highest elevation plots as a result of more recent disturbance in this area. While flood frequency and duration define the delivery mechanism for inundation on the flood plain, it is the duration of ponding and amount of 'topographic capture' of these floodwaters in fluvial lan

Using Multi-Scenario Tsunami Modelling Results combined with Probabilistic Analyses to provide Hazard Information for the South-WestCoast of Indonesia

NASA Astrophysics Data System (ADS)

Zosseder, K.; Post, J.; Steinmetz, T.; Wegscheider, S.; Strunz, G.

2009-04-01

Indonesia is located at one of the most active geological subduction zones in the world. Following the most recent seaquakes and their subsequent tsunamis in December 2004 and July 2006 it is expected that also in the near future tsunamis are likely to occur due to increased tectonic tensions leading to abrupt vertical seafloor alterations after a century of relative tectonic silence. To face this devastating threat tsunami hazard maps are very important as base for evacuation planning and mitigation strategies. In terms of a tsunami impact the hazard assessment is mostly covered by numerical modelling because the model results normally offer the most precise database for a hazard analysis as they include spatially distributed data and their influence to the hydraulic dynamics. Generally a model result gives a probability for the intensity distribution of a tsunami at the coast (or run up) and the spatial distribution of the maximum inundation area depending on the location and magnitude of the tsunami source used. The boundary condition of the source used for the model is mostly chosen by a worst case approach. Hence the location and magnitude which are likely to occur and which are assumed to generate the worst impact are used to predict the impact at a specific area. But for a tsunami hazard assessment covering a large coastal area, as it is demanded in the GITEWS (German Indonesian Tsunami Early Warning System) project in which the present work is embedded, this approach is not practicable because a lot of tsunami sources can cause an impact at the coast and must be considered. Thus a multi-scenario tsunami model approach is developed to provide a reliable hazard assessment covering large areas. For the Indonesian Early Warning System many tsunami scenarios were modelled by the Alfred Wegener Institute (AWI) at different probable tsunami sources and with different magnitudes along the Sunda Trench. Every modelled scenario delivers the spatial distribution of the inundation for a specific area, the wave height at coast at this area and the estimated times of arrival (ETAs) of the waves, caused by one tsunamigenic source with a specific magnitude. These parameters from the several scenarios can overlap each other along the coast and must be combined to get one comprehensive hazard assessment for all possible future tsunamis at the region under observation. The simplest way to derive the inundation probability along the coast using the multiscenario approach is to overlay all scenario inundation results and to determine how often a point on land will be significantly inundated from the various scenarios. But this does not take into account that the used tsunamigenic sources for the modeled scenarios have different likelihoods of causing a tsunami. Hence a statistical analysis of historical data and geophysical investigation results based on numerical modelling results is added to the hazard assessment, which clearly improves the significance of the hazard assessment. For this purpose the present method is developed and contains a complex logical combination of the diverse probabilities assessed like probability of occurrence for different earthquake magnitudes at different localities, probability of occurrence for a specific wave height at the coast and the probability for every point on land likely to get hit by a tsunami. The values are combined by a logical tree technique and quantified by statistical analysis of historical data and of the tsunami modelling results as mentioned before. This results in a tsunami inundation probability map covering the South West Coast of Indonesia which nevertheless shows a significant spatial diversity offering a good base for evacuation planning and mitigation strategies. Keywords: tsunami hazard assessment, tsunami modelling, probabilistic analysis, early warning

Land cover change impact on urban flood modeling (case study: Upper Citarum watershed)

NASA Astrophysics Data System (ADS)

Siregar, R. I.

2018-03-01

The upper Citarum River watershed utilizes remote sensing technology in Geographic Information System to provide information on land coverage by interpretation of objects in the image. Rivers that pass through urban areas will cause flooding problems causing disadvantages, and it disrupts community activities in the urban area. Increased development in a city is related to an increase in the number of population growth that added by increasing quality and quantity of life necessities. Improved urban lifestyle changes have an impact on land cover. The impact in over time will be difficult to control. This study aims to analyze the condition of flooding in urban areas caused by upper Citarum watershed land-use change in 2001 with the land cover change in 2010. This modeling analyzes with the help of HEC-RAS to describe flooded inundation urban areas. Land cover change in upper Citarum watershed is not very significant; it based on the results of data processing of land cover has the difference of area that changed is not enormous. Land cover changes for the floods increased dramatically to a flow coefficient for 2001 is 0.65 and in 2010 at 0.69. In 2001, the inundation area about 105,468 hectares and it were about 92,289 hectares in 2010.

Biogeochemical cycling at the aquatic-terrestrial interface is linked to parafluvial hyporheic zone inundation history

NASA Astrophysics Data System (ADS)

Goldman, Amy E.; Graham, Emily B.; Crump, Alex R.; Kennedy, David W.; Romero, Elvira B.; Anderson, Carolyn G.; Dana, Karl L.; Resch, Charles T.; Fredrickson, Jim K.; Stegen, James C.

2017-09-01

The parafluvial hyporheic zone combines the heightened biogeochemical and microbial interactions indicative of a hyporheic region with direct atmospheric/terrestrial inputs and the effects of wet-dry cycles. Therefore, understanding biogeochemical cycling and microbial interactions in this ecotone is fundamental to understanding biogeochemical cycling at the aquatic-terrestrial interface and to creating robust hydrobiogeochemical models of dynamic river corridors. We aimed to (i) characterize biogeochemical and microbial differences in the parafluvial hyporheic zone across a small spatial domain (6 lateral meters) that spans a breadth of inundation histories and (ii) examine how parafluvial hyporheic sediments respond to laboratory-simulated re-inundation. Surface sediment was collected at four elevations along transects perpendicular to flow of the Columbia River, eastern WA, USA. The sediments were inundated by the river 0, 13, 127, and 398 days prior to sampling. Spatial variation in environmental variables (organic matter, moisture, nitrate, glucose, % C, % N) and microbial communities (16S and internal transcribed spacer (ITS) rRNA gene sequencing, qPCR) were driven by differences in inundation history. Microbial respiration did not differ significantly across inundation histories prior to forced inundation in laboratory incubations. Forced inundation suppressed microbial respiration across all histories, but the degree of suppression was dramatically different between the sediments saturated and unsaturated at the time of sample collection, indicating a binary threshold response to re-inundation. We present a conceptual model in which irregular hydrologic fluctuations facilitate microbial communities adapted to local conditions and a relatively high flux of CO2. Upon rewetting, microbial communities are initially suppressed metabolically, which results in lower CO2 flux rates primarily due to suppression of fungal respiration. Following prolonged inundation, the microbial community adapts to saturation by shifting composition, and the CO2 flux rebounds to prior levels due to the subsequent change in respiration. Our results indicate that the time between inundation events can push the system into alternate states: we suggest (i) that, above some threshold of inundation interval, re-inundation suppresses respiration to a consistent, low rate and (ii) that, below some inundation interval, re-inundation has a minor effect on respiration. Extending reactive transport models to capture processes that govern such dynamics will provide more robust predictions of river corridor biogeochemical function under altered surface water flow regimes in both managed and natural watersheds.

Validation of tsunami inundation model TUNA-RP using OAR-PMEL-135 benchmark problem set

NASA Astrophysics Data System (ADS)

Koh, H. L.; Teh, S. Y.; Tan, W. K.; Kh'ng, X. Y.

2017-05-01

A standard set of benchmark problems, known as OAR-PMEL-135, is developed by the US National Tsunami Hazard Mitigation Program for tsunami inundation model validation. Any tsunami inundation model must be tested for its accuracy and capability using this standard set of benchmark problems before it can be gainfully used for inundation simulation. The authors have previously developed an in-house tsunami inundation model known as TUNA-RP. This inundation model solves the two-dimensional nonlinear shallow water equations coupled with a wet-dry moving boundary algorithm. This paper presents the validation of TUNA-RP against the solutions provided in the OAR-PMEL-135 benchmark problem set. This benchmark validation testing shows that TUNA-RP can indeed perform inundation simulation with accuracy consistent with that in the tested benchmark problem set.

Computerized Workstation for Tsunami Hazard Monitoring

NASA Astrophysics Data System (ADS)

Lavrentiev-Jr, Mikhail; Marchuk, Andrey; Romanenko, Alexey; Simonov, Konstantin; Titov, Vasiliy

2010-05-01

We present general structure and functionality of the proposed Computerized Workstation for Tsunami Hazard Monitoring (CWTHM). The tool allows interactive monitoring of hazard, tsunami risk assessment, and mitigation - at all stages, from the period of strong tsunamigenic earthquake preparation to inundation of the defended coastal areas. CWTHM is a software-hardware complex with a set of software applications, optimized to achieve best performance on hardware platforms in use. The complex is calibrated for selected tsunami source zone(s) and coastal zone(s) to be defended. The number of zones (both source and coastal) is determined, or restricted, by available hardware resources. The presented complex performs monitoring of selected tsunami source zone via the Internet. The authors developed original algorithms, which enable detection of the preparation zone of the strong underwater earthquake automatically. For the so-determined zone the event time, magnitude and spatial location of tsunami source are evaluated by means of energy of the seismic precursors (foreshocks) analysis. All the above parameters are updated after each foreshock. Once preparing event is detected, several scenarios are forecasted for wave amplitude parameters as well as the inundation zone. Estimations include the lowest and the highest wave amplitudes and the least and the most inundation zone. In addition to that, the most probable case is calculated. In case of multiple defended coastal zones, forecasts and estimates can be done in parallel. Each time the simulated model wave reaches deep ocean buoys or tidal gauge, expected values of wave parameters and inundation zones are updated with historical events information and pre-calculated scenarios. The Method of Splitting Tsunami (MOST) software package is used for mathematical simulation. The authors suggest code acceleration for deep water wave propagation. As a result, performance is 15 times faster compared to MOST, original version. Performance gain is achieved by compiler options, use of optimized libraries, and advantages of OpenMP parallel technology. Moreover, it is possible to achieve 100 times code acceleration by using modern Graphics Processing Units (GPU). Parallel evaluation of inundation zones for multiple coastal zones is also available. All computer codes can be easily assembled under MS Windows and Unix OS family. Although software is virtually platform independent, the most performance gain is achieved while using the recommended hardware components. When the seismic event occurs, all valuable parameters are updated with seismic data and wave propagation monitoring is enabled. As soon as the wave passes each deep ocean tsunameter, parameters of the initial displacement at source are updated from direct calculations based on original algorithms. For better source reconstruction, a combination of two methods is used: optimal unit source linear combination from preliminary calculated database and direct numerical inversion along the wave ray between real source and particular measurement buoys. Specific dissipation parameter along with the wave ray is also taken into account. During the entire wave propagation process the expected wave parameters and inundation zone(s) characteristics are updated with all available information. If recommended hardware components are used, monitoring results are available in real time. The suggested version of CWTHM has been tested by analyzing seismic precursors (foreshocks) and the measured tsunami waves at North Pacific for the Central Kuril's tsunamigenic earthquake of November 15, 2006.

40 CFR 230.43 - Vegetated shallows.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Special Aquatic Sites § 230.43 Vegetated shallows. (a) Vegetated shallows are permanently inundated areas that under normal circumstances support communities of rooted aquatic vegetation, such as turtle grass...) releasing chemicals that adversely affect plants and animals; (4) increasing turbidity levels, thereby...

The October 2015 flash-floods in south eastern France: hydrological analyses, inundation mapping and impact estimations

NASA Astrophysics Data System (ADS)

Payrastre, Olivier; Bourgin, François; Lebouc, Laurent; Le Bihan, Guillaume; Gaume, Eric

2017-04-01

The October 2015 flash-floods in south eastern France caused more than twenty fatalities, high damages and large economic losses in high density urban areas of the Mediterranean coast, including the cities of Mandelieu-La Napoule, Cannes and Antibes. Following a post event survey and preliminary analyses conducted within the framework of the Hymex project, we set up an entire simulation chain at the regional scale to better understand this outstanding event. Rainfall-runoff simulations, inundation mapping and a first estimation of the impacts are conducted following the approach developed and successfully applied for two large flash-flood events in two different French regions (Gard in 2002 and Var in 2010) by Le Bihan (2016). A distributed rainfall-runoff model applied at high resolution for the whole area - including numerous small ungauged basins - is used to feed a semi-automatic hydraulic approach (Cartino method) applied along the river network - including small tributaries. Estimation of the impacts is then performed based on the delineation of the flooded areas and geographic databases identifying buildings and population at risk.

A barrage of beetles: controlling leafy spurge through beetle inundation

Treesearch

Paul Meznarich; Rob Progar

2012-01-01

Leafy spurge is an invasive weed that has appeared along streams throughout much of the country. Riparian ecosystems are particularly sensitive areas that can be threatened by nonnative invasive species. These areas also can be damaged by herbicides commonly used in uplands to control invasive plants. In a collaborative effort by the U.S. Forest Service, Bureau of Land...

Simulated tsunami run-up amplification factors around Penang Island for preliminary risk assessment

NASA Astrophysics Data System (ADS)

Lim, Yong Hui; Kh'ng, Xin Yi; Teh, Su Yean; Koh, Hock Lye; Tan, Wai Kiat

2017-08-01

The mega-tsunami Andaman that struck Malaysia on 26 December 2004 affected 200 kilometers of northwest Peninsular Malaysia coastline from Perlis to Selangor. It is anticipated by the tsunami scientific community that the next mega-tsunami is due to occur any time soon. This rare catastrophic event has awakened the attention of Malaysian government to take appropriate risk reduction measures, including timely and orderly evacuation. To effectively evacuate ordinary citizens to a safe ground or a nearest designated emergency shelter, a well prepared evacuation route is essential with the estimated tsunami run-up heights and inundation distances on land clearly indicated on the evacuation map. The run-up heights and inundation distances are simulated by an in-house model 2-D TUNA-RP based upon credible scientific tsunami source scenarios derived from tectonic activity around the region. To provide a useful tool for estimating the run-up heights along the entire coast of Penang Island, we computed tsunami amplification factors based upon 2-D TUNA-RP model simulations in this paper. The inundation map and run-up amplification factors in six domains along the entire coastline of Penang Island are provided. The comparison between measured tsunami wave heights for the 2004 Andaman tsunami and TUNA-RP model simulated values demonstrates good agreement.

A New Method of Providing Communities With High-Resolution Maps of Present and Future Inundation Pathways: Two Examples From Massachusetts

NASA Astrophysics Data System (ADS)

Borrelli, M.; Mague, S. T.; Smith, T. L.

2015-12-01

A new method of mapping storm-tide (inundation) pathways and linking those data with tidal elevations in real-time for local managers is being developed. Separate, ongoing studies in two coastal towns in Massachusetts have demonstrated the strengths of this method. High-resolution lidar datasets are imported into 3D data visualization software and water levels are raised incrementally from the highest spring tide of the year to the storm of record +1 m. This range was identified to include 'nuisance flooding' as well as present and future inundation pathways not yet observed by local authorities caused by storms superimposed on projected sea level rise. Potential storm-tide pathways are identified using Lidar data but are then verified with extensive fieldwork using RTK-GPS instruments (tested vertical accuracy of 4.9 cm at 95%) to overcome the vertical uncertainty associated with Lidar data. The fieldwork serves two purposes, first is to field check the lidar data with the highest resolution instrument available and, second to verify and document the presence or absence of a storm-tide pathway. Having developed the map of storm tide pathways within a GIS environment referenced to a geodetic datum (NAVD88), a tide gauge or staff is installed in the town's harbor or other sheltered coastal area and the elevations of all storm tide pathways are then referenced to the local tidal datum. The benefit here is three-fold. First, local officials can use the high-resolution data set that is tied to a local tidal datum to autonomously monitor predicted storm surges and be prepared for inundation at sites prior to flooding. Second, storm-tide pathways that have heretofore never been inundated can be identified and steps can be taken to remove or minimize flooding hazards. Finally, identification of present and future storm tide pathways can be used to prioritize and budget proactive solutions in response to increases in chronic, nuisance and more frequent flooding associated with sea level rise and climate change. This method does not rely on costly numerical models that are often too coarsely gridded to be of use on a street-by-street basis. Lidar data are publicly available in many coastal areas and can be used with little training to new or already existing local or regional GIS staff.

Advanced Regional and Decadal Predictions of Coastal Inundation for the U.S. Atlantic and Gulf Coasts (Invited)

NASA Astrophysics Data System (ADS)

Horton, B.; Corbett, D. R.; Donnelly, J. P.; Kemp, A.; Lin, N.; Lindeman, K.; Mann, M. E.; Peltier, W. R.; Rahmstorf, S.

2013-12-01

Future inundation of the U.S. Atlantic and Gulf coasts will depend upon sea-level rise and the intensity and frequency of tropical cyclones, each of which will be affected by climate change. Through ongoing, collaborative research we are employing new interdisciplinary approaches to bring about a step change in the reliability of predictions of such inundation. The rate of sea level rise along the U.S. Atlantic and Gulf coasts increased throughout the 20th century. Whilst there is widespread agreement that it continue to accelerate during the 21st century, great uncertainty surrounds its magnitude and geographic variability. Key uncertainties include the role of continental ice sheets, mountain glaciers, and ocean density changes. Insufficient understanding of these complex physical processes precludes accurate prediction of sea-level rise. New approaches using semi-empirical models that relate instrumental records of climate and sea-level rise have projected up to 2 m of sea-level rise by AD 2100. But the time span of instrumental sea-level records is insufficient to adequately constrain the climate:sea-level relationship. We produced new, high-resolution proxy sea-level reconstructions to provide crucial additional constraints to such semi-empirical models. Our dataset spans the alternation between the 'Medieval Climate Anomaly' and 'Little Ice Age'. Before the models can provide appropriate data for coastal management and planning, they must be complemented with regional estimates of sea-level rise. Therefore, the proxy sea-level data has been collected from four study areas (Connecticut, New Jersey, North Carolina and Florida) to accommodate the required extent of regional variability. In the case of inundation arising from tropical cyclones, the historical and observational records are insufficient for predicting their nature and recurrence, because they are such extreme and rare events. Moreover, future storm surges will be superimposed on background sea-level rise. To overcome these problems, we coupled regional sea-level rise projections with hurricane simulations and storm surge models to map coastal inundation for the current climate and the best and worst case climate scenarios of the IPCC AR4. With agency, NGO, and business partners, we have integrated these findings into coastal policy initiatives, including the first ever adoption of sea level Adaptation Action Areas in a Florida city land use plan.

Evaluation of tsunami risk in Heraklion city, Crete, Greece, by using GIS methods

NASA Astrophysics Data System (ADS)

Triantafyllou, Ioanna; Fokaefs, Anna; Novikova, Tatyana; Papadopoulos, Gerasimos A.; Vaitis, Michalis

2016-04-01

The Hellenic Arc is the most active seismotectonic structure in the Mediterranean region. The island of Crete occupies the central segment of the arc which is characterized by high seismic and tsunami activity. Several tsunamis generated by large earthquakes, volcanic eruptions and landslides were reported that hit the capital city of Heraklion in the historical past. We focus our tsunami risk study in the northern coastal area of Crete (ca. 6 km in length and 1 km in maximum width) which includes the western part of the city of Heraklion and a large part of the neighboring municipality of Gazi. The evaluation of tsunami risk included calculations and mapping with QGIS of (1) cost for repairing buildings after tsunami damage, (2) population exposed to tsunami attack, (3) optimum routes and times for evacuation. To calculate the cost for building reparation after a tsunami attack we have determined the tsunami inundation zone in the study area after numerical simulations for extreme tsunami scenarios. The geographical distribution of buildings per building block, obtained from the 2011 census data of the Hellenic Statistical Authority (EL.STAT) and satellite data, was mapped. By applying the SCHEMA Damage Tool we assessed the building vulnerability to tsunamis according to the types of buildings and their expected damage from the hydrodynamic impact. A set of official cost rates varying with the building types and the damage levels, following standards set by the state after the strong damaging earthquakes in Greece in 2014, was applied to calculate the cost of rebuilding or repairing buildings damaged by the tsunami. In the investigation of the population exposed to tsunami inundation we have used the interpolation method to smooth out the population geographical distribution per building block within the inundation zone. Then, the population distribution was correlated with tsunami hydrodynamic parameters in the inundation zone. The last approach of tsunami risk assessment refers to the selection of optimal routes and times needed for evacuation from certain points within the inundation zone to a number of shelters outside the zone. The three different approaches were evaluated as for their overall contribution in the development of a plan for the tsunami risk mitigation. This research is a contribution to the EU-FP7 tsunami research project ASTARTE (Assessment, Strategy And Risk Reduction for Tsunamis in Europe), grant agreement no: 603839, 2013-10-30.

A mangrove forest map of China in 2015: Analysis of time series Landsat 7/8 and Sentinel-1A imagery in Google Earth Engine cloud computing platform

NASA Astrophysics Data System (ADS)

Chen, Bangqian; Xiao, Xiangming; Li, Xiangping; Pan, Lianghao; Doughty, Russell; Ma, Jun; Dong, Jinwei; Qin, Yuanwei; Zhao, Bin; Wu, Zhixiang; Sun, Rui; Lan, Guoyu; Xie, Guishui; Clinton, Nicholas; Giri, Chandra

2017-09-01

Due to rapid losses of mangrove forests caused by anthropogenic disturbances and climate change, accurate and contemporary maps of mangrove forests are needed to understand how mangrove ecosystems are changing and establish plans for sustainable management. In this study, a new classification algorithm was developed using the biophysical characteristics of mangrove forests in China. More specifically, these forests were mapped by identifying: (1) greenness, canopy coverage, and tidal inundation from time series Landsat data, and (2) elevation, slope, and intersection-with-sea criterion. The annual mean Normalized Difference Vegetation Index (NDVI) was found to be a key variable in determining the classification thresholds of greenness, canopy coverage, and tidal inundation of mangrove forests, which are greatly affected by tide dynamics. In addition, the integration of Sentinel-1A VH band and modified Normalized Difference Water Index (mNDWI) shows great potential in identifying yearlong tidal and fresh water bodies, which is related to mangrove forests. This algorithm was developed using 6 typical Regions of Interest (ROIs) as algorithm training and was run on the Google Earth Engine (GEE) cloud computing platform to process 1941 Landsat images (25 Path/Row) and 586 Sentinel-1A images circa 2015. The resultant mangrove forest map of China at 30 m spatial resolution has an overall/users/producer's accuracy greater than 95% when validated with ground reference data. In 2015, China's mangrove forests had a total area of 20,303 ha, about 92% of which was in the Guangxi Zhuang Autonomous Region, Guangdong, and Hainan Provinces. This study has demonstrated the potential of using the GEE platform, time series Landsat and Sentine-1A SAR images to identify and map mangrove forests along the coastal zones. The resultant mangrove forest maps are likely to be useful for the sustainable management and ecological assessments of mangrove forests in China.

Combined fluvial and pluvial urban flood hazard analysis: method development and application to Can Tho City, Mekong Delta, Vietnam

NASA Astrophysics Data System (ADS)

Apel, H.; Trepat, O. M.; Hung, N. N.; Chinh, D. T.; Merz, B.; Dung, N. V.

2015-08-01

Many urban areas experience both fluvial and pluvial floods, because locations next to rivers are preferred settlement areas, and the predominantly sealed urban surface prevents infiltration and facilitates surface inundation. The latter problem is enhanced in cities with insufficient or non-existent sewer systems. While there are a number of approaches to analyse either fluvial or pluvial flood hazard, studies of combined fluvial and pluvial flood hazard are hardly available. Thus this study aims at the analysis of fluvial and pluvial flood hazard individually, but also at developing a method for the analysis of combined pluvial and fluvial flood hazard. This combined fluvial-pluvial flood hazard analysis is performed taking Can Tho city, the largest city in the Vietnamese part of the Mekong Delta, as example. In this tropical environment the annual monsoon triggered floods of the Mekong River can coincide with heavy local convective precipitation events causing both fluvial and pluvial flooding at the same time. Fluvial flood hazard was estimated with a copula based bivariate extreme value statistic for the gauge Kratie at the upper boundary of the Mekong Delta and a large-scale hydrodynamic model of the Mekong Delta. This provided the boundaries for 2-dimensional hydrodynamic inundation simulation for Can Tho city. Pluvial hazard was estimated by a peak-over-threshold frequency estimation based on local rain gauge data, and a stochastic rain storm generator. Inundation was simulated by a 2-dimensional hydrodynamic model implemented on a Graphical Processor Unit (GPU) for time-efficient flood propagation modelling. All hazards - fluvial, pluvial and combined - were accompanied by an uncertainty estimation considering the natural variability of the flood events. This resulted in probabilistic flood hazard maps showing the maximum inundation depths for a selected set of probabilities of occurrence, with maps showing the expectation (median) and the uncertainty by percentile maps. The results are critically discussed and ways for their usage in flood risk management are outlined.

Measuring Sea Level Rise-Induced Shoreline Changes and Inundation in Real Time

NASA Astrophysics Data System (ADS)

Shilling, F.; Waetjen, D.; Grijalva, E.

2016-12-01

We describe a method to monitor shoreline inundation and changes in response to sea level rise (SLR) using a network of time-lapse cameras. We found for coastal tidal marshes that this method was sensitive to vertical changes in sea level of <1 cm, roughly equivalent to 1-2 years of sea level rise under the A1 scenario. SLR of >20 cm has occurred in the San Francisco Bay and other US coastal areas and is likely to rise by another 30-45 cm by mid-century, which will flood and erode many coastal ecosystems, highways, and urban areas. This rapid degree of rise means that it is imperative to co-plan for natural and built systems. Many public facilities are adjacent to shoreline ecosystems, which both protect infrastructure from wave and tide energy and are home to regulated species and habitats. Accurate and timely information about the actual extent of SLR impacts to shorelines will be critical during built-system adaptation. Currently, satellite-sourced imagery cannot provide the spatial or temporal resolution necessary to investigate fine-scale shoreline changes, leaving a gap between predictive models and knowing how, where and when these changes are occurring. The method described is feasible for near-term (1 to 10 years) to long-term application and can be used for measuring fine-resolution shoreline changes (<1 m2) in response to SLR and associated wave action inundation of marshes and infrastructure. We demonstrate the method with networks of cameras in 2 coastal states (CA and GA), using web-informatics and services to organize photographs that could be combined with related external data (e.g., gauged water levels) to create an information mashup. This information could be used to validate models predicting shoreline inundation and loss, inform SLR-adaptation planning, and to visualize SLR impacts to the public.

Use of individualistic streamflow-vegetation relations along the Fremont River, Utah, USA to assess impacts of flow alteration on wetland and riparian area

USGS Publications Warehouse

Auble, G.T.; Scott, M.L.; Friedman, J.M.

2005-01-01

We analyzed the transverse pattern of vegetation along a reach of the Fremont River in Capitol Reef National Park, Utah, USA using models that support both delineation of wetland extent and projection of the changes in wetland area resulting from upstream hydrologic alteration. We linked stage-discharge relations developed by a hydraulic model to a flow-duration curve derived from the flow history in order to calculate the inundation duration of 361 plots (0.5 × 2 m). Logistic regression was used to relate plant species occurrence in plots to inundation duration. A weighted average of the wetland indicator values of species was used to characterize plots as Aquatic, Wetland, Transitional, or Upland. Finally, we assessed how alterations in the flow duration curve would change the relative widths of these four zones. The wetland indicator values of species and the wetland prevalence index scores of plots were strongly correlated with inundation duration. Our results support the concept that plants classified as wetland species typically occur on sites inundated at least two weeks every two years. The portion of the riparian zone along the high-gradient study reach of the Fremont River that satisfied the vegetation criterion for a regulatory wetland was narrow (2 m wide). Both the unvegetated Aquatic zone (7.8 m) and the Transitional zone (8 m) were substantially wider. The Transitional zone included the maxima of several species and was, therefore, not merely a combination of elements of the Wetland and Upland zones. Multiplicative increases or decreases in streamflow regime produced a wetter, or drier, bottomland vegetation, respectively. Systematic reductions in flow variability reduced the width of both the Wetland and Transitional zones and increased the width of the Upland zone. Our approach is widely applicable to inform water management decisions involving changes in flow regime.

Air Force Information Management (IM): A 1990 Snapshot and 1995 Future Look at Air Force IM Needs and Preferred Education/Training Approaches

DTIC Science & Technology

1990-12-01

small powerful computers to businesses and homes on an international scale (29:74). Relatively low cost, high computing power , and ease of operation were...is performed. In large part, today’s AF IM professional has been inundated with powerful new technologies which were rapidly introduced and inserted...state that, "In a survey of five years of MIS research, we fouind the averane levels of statistical power to be relatively low (5:104). In their own

Will inundation and salinity levels associated with projected sea level rise reduce the survival, growth, and reproductive capacity of Sarcocornia pacifica (pickleweed)?

USGS Publications Warehouse

Woo, I.; Takekawa, John Y.

2012-01-01

In the San Francisco Bay Estuary, CA, USA, sea level rise (SLR) is projected to increase by 1.4 m during the next 90 years resulting in increased inundation and salt water intrusion up-estuary. Since inundation and salinity are critical factors that drive vegetation structure and composition in coastal wetlands, we asked whether inundation and salinity levels associated with SLR would reduce the survival, growth, and reproductive capacity of a dominant halophyte, Sarcocornia pacifica (pickleweed). We conducted a 4 × 4 factorial greenhouse experiment to examine the effects of a range of inundation periods (25, 50, 75, and 100%) and water salinities (0, 10, 20, 30 psu) on individual S. pacifica adults and seedlings. We found that inundation and salinity treatments affected the height of adults and seedlings combined. When examined separately, adult height was negatively affected by inundation ≥75%, while seedling height was affected by the interaction of both inundation and salinity. Adult belowground biomass was negatively affected by complete inundation. Seedling aboveground biomass decreased 46% at the highest salinity (30 psu) and belowground biomass decreased at salinities ≥20 psu. Adult flower production was not affected by treatments but was reduced by 38% at 30 psu salinity for seedlings. While adult survival was 99%, seedling survival was 56% with greatest mortality at low (25%) inundation, possibly because their roots were more susceptible to desiccation. Vegetation structure of the marsh platform comprised of S. pacifica adults will be susceptible to greater inundation rates associated with SLR. Our results suggest that adults may grow less tall, thus altering the vegetation structure and likely the tidal marsh wildlife that rely on these habitats.

Towards an integrated strategy for monitoring wetland inundation with virtual constellations of optical and radar satellites

NASA Astrophysics Data System (ADS)

DeVries, B.; Huang, W.; Huang, C.; Jones, J. W.; Lang, M. W.; Creed, I. F.; Carroll, M.

2017-12-01

The function of wetlandscapes in hydrological and biogeochemical cycles is largely governed by surface inundation, with small wetlands that experience periodic inundation playing a disproportionately large role in these processes. However, the spatial distribution and temporal dynamics of inundation in these wetland systems are still poorly understood, resulting in large uncertainties in global water, carbon and greenhouse gas budgets. Satellite imagery provides synoptic and repeat views of the Earth's surface and presents opportunities to fill this knowledge gap. Despite the proliferation of Earth Observation satellite missions in the past decade, no single satellite sensor can simultaneously provide the spatial and temporal detail needed to adequately characterize inundation in small, dynamic wetland systems. Surface water data products must therefore integrate observations from multiple satellite sensors in order to address this objective, requiring the development of improved and coordinated algorithms to generate consistent estimates of surface inundation. We present a suite of algorithms designed to detect surface inundation in wetlands using data from a virtual constellation of optical and radar sensors comprising the Landsat and Sentinel missions (DeVries et al., 2017). Both optical and radar algorithms were able to detect inundation in wetlands without the need for external training data, allowing for high-efficiency monitoring of wetland inundation at large spatial and temporal scales. Applying these algorithms across a gradient of wetlands in North America, preliminary findings suggest that while these fully automated algorithms can detect wetland inundation at higher spatial and temporal resolutions than currently available surface water data products, limitations specific to the satellite sensors and their acquisition strategies are responsible for uncertainties in inundation estimates. Further research is needed to investigate strategies for integrating optical and radar data from virtual constellations, with a focus on reducing uncertainties, maximizing spatial and temporal detail, and establishing consistent records of wetland inundation over time. The findings and conclusions in this article do not necessarily represent the views of the U.S. Government.

An Integrated Coastal Observation and Flood Warning System: Rapid Prototype Development

DTIC Science & Technology

2006-09-01

And Ranging (LIDAR) tiles describing the area of interest are critical to the accuracy of the associated graphical representations of the inundation...Elevation Dataset (NED) with 30-meter resolution for the upper Potomac area and USGS 0.3-meter resolution orthophotos for viewing when zoomed down...on the areas of interest. Using orthophotos is much easier than trying to recreate the landscape with point, line, and polygon features, and it

Biogeochemical cycling at the aquatic–terrestrial interface is linked to parafluvial hyporheic zone inundation history

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldman, Amy E.; Graham, Emily B.; Crump, Alex R.

The parafluvial hyporheic zone combines the heightened biogeochemical and microbial interactions indicative of a hyporheic region with direct atmospheric/terrestrial inputs and the effects of wet–dry cycles. Therefore, understanding biogeochemical cycling and microbial interactions in this ecotone is fundamental to understanding biogeochemical cycling at the aquatic–terrestrial interface and to creating robust hydrobiogeochemical models of dynamic river corridors. We aimed to (i) characterize biogeochemical and microbial differences in the parafluvial hyporheic zone across a small spatial domain (6 lateral meters) that spans a breadth of inundation histories and (ii) examine how parafluvial hyporheic sediments respond to laboratory-simulated re-inundation. Surface sediment was collected at fourmore » elevations along transects perpendicular to flow of the Columbia River, eastern WA, USA. The sediments were inundated by the river 0, 13, 127, and 398 days prior to sampling. Spatial variation in environmental variables (organic matter, moisture, nitrate, glucose, %C, %N) and microbial communities (16S and internal transcribed spacer (ITS) rRNA gene sequencing, qPCR) were driven by differences in inundation history. Microbial respiration did not differ significantly across inundation histories prior to forced inundation in laboratory incubations. Forced inundation suppressed microbial respiration across all histories, but the degree of suppression was dramatically different between the sediments saturated and unsaturated at the time of sample collection, indicating a binary threshold response to re-inundation. We present a conceptual model in which irregular hydrologic fluctuations facilitate microbial communities adapted to local conditions and a relatively high flux of CO 2. Upon rewetting, microbial communities are initially suppressed metabolically, which results in lower CO 2 flux rates primarily due to suppression of fungal respiration. Following prolonged inundation, the microbial community adapts to saturation by shifting composition, and the CO 2 flux rebounds to prior levels due to the subsequent change in respiration. Our results indicate that the time between inundation events can push the system into alternate states: we suggest (i) that, above some threshold of inundation interval, re-inundation suppresses respiration to a consistent, low rate and (ii) that, below some inundation interval, re-inundation has a minor effect on respiration. In conclusion, extending reactive transport models to capture processes that govern such dynamics will provide more robust predictions of river corridor biogeochemical function under altered surface water flow regimes in both managed and natural watersheds.« less

Biogeochemical cycling at the aquatic–terrestrial interface is linked to parafluvial hyporheic zone inundation history

DOE PAGES

Goldman, Amy E.; Graham, Emily B.; Crump, Alex R.; ...

2017-09-21

The parafluvial hyporheic zone combines the heightened biogeochemical and microbial interactions indicative of a hyporheic region with direct atmospheric/terrestrial inputs and the effects of wet–dry cycles. Therefore, understanding biogeochemical cycling and microbial interactions in this ecotone is fundamental to understanding biogeochemical cycling at the aquatic–terrestrial interface and to creating robust hydrobiogeochemical models of dynamic river corridors. We aimed to (i) characterize biogeochemical and microbial differences in the parafluvial hyporheic zone across a small spatial domain (6 lateral meters) that spans a breadth of inundation histories and (ii) examine how parafluvial hyporheic sediments respond to laboratory-simulated re-inundation. Surface sediment was collected at fourmore » elevations along transects perpendicular to flow of the Columbia River, eastern WA, USA. The sediments were inundated by the river 0, 13, 127, and 398 days prior to sampling. Spatial variation in environmental variables (organic matter, moisture, nitrate, glucose, %C, %N) and microbial communities (16S and internal transcribed spacer (ITS) rRNA gene sequencing, qPCR) were driven by differences in inundation history. Microbial respiration did not differ significantly across inundation histories prior to forced inundation in laboratory incubations. Forced inundation suppressed microbial respiration across all histories, but the degree of suppression was dramatically different between the sediments saturated and unsaturated at the time of sample collection, indicating a binary threshold response to re-inundation. We present a conceptual model in which irregular hydrologic fluctuations facilitate microbial communities adapted to local conditions and a relatively high flux of CO 2. Upon rewetting, microbial communities are initially suppressed metabolically, which results in lower CO 2 flux rates primarily due to suppression of fungal respiration. Following prolonged inundation, the microbial community adapts to saturation by shifting composition, and the CO 2 flux rebounds to prior levels due to the subsequent change in respiration. Our results indicate that the time between inundation events can push the system into alternate states: we suggest (i) that, above some threshold of inundation interval, re-inundation suppresses respiration to a consistent, low rate and (ii) that, below some inundation interval, re-inundation has a minor effect on respiration. In conclusion, extending reactive transport models to capture processes that govern such dynamics will provide more robust predictions of river corridor biogeochemical function under altered surface water flow regimes in both managed and natural watersheds.« less

Wetlands, Chapter 17

Treesearch

T.L. Greaver; L. Liu; R. Bobbink

2011-01-01

The U.S. Clean Water Act defines wetlands as "those areas that are inundated or saturated by surface or ground water at a frequency and duration sufficient to support, and that under normal circumstances do support, a prevalence of vegetation typically adapted for life in saturated soil conditions".

Local SPTHA through tsunami inundation simulations: a test case for two coastal critical infrastructures in the Mediterranean

NASA Astrophysics Data System (ADS)

Volpe, M.; Selva, J.; Tonini, R.; Romano, F.; Lorito, S.; Brizuela, B.; Argyroudis, S.; Salzano, E.; Piatanesi, A.

2016-12-01

Seismic Probabilistic Tsunami Hazard Analysis (SPTHA) is a methodology to assess the exceedance probability for different thresholds of tsunami hazard intensity, at a specific site or region in a given time period, due to a seismic source. A large amount of high-resolution inundation simulations is typically required for taking into account the full variability of potential seismic sources and their slip distributions. Starting from regional SPTHA offshore results, the computational cost can be reduced by considering for inundation calculations only a subset of `important' scenarios. We here use a method based on an event tree for the treatment of the seismic source aleatory variability; a cluster analysis on the offshore results to define the important sources; epistemic uncertainty treatment through an ensemble modeling approach. We consider two target sites in the Mediterranean (Milazzo, Italy, and Thessaloniki, Greece) where coastal (non nuclear) critical infrastructures (CIs) are located. After performing a regional SPTHA covering the whole Mediterranean, for each target site, few hundreds of representative scenarios are filtered out of all the potential seismic sources and the tsunami inundation is explicitly modeled, obtaining a site-specific SPTHA, with a complete characterization of the tsunami hazard in terms of flow depth and velocity time histories. Moreover, we also explore the variability of SPTHA at the target site accounting for coseismic deformation (i.e. uplift or subsidence) due to near field sources located in very shallow water. The results are suitable and will be applied for subsequent multi-hazard risk analysis for the CIs. These applications have been developed in the framework of the Italian Flagship Project RITMARE, EC FP7 ASTARTE (Grant agreement 603839) and STREST (Grant agreement 603389) projects, and of the INGV-DPC Agreement.

Evacuation planning for plausible worst case inundation scenarios in Honolulu, Hawaii.

PubMed

Kim, Karl; Pant, Pradip; Yamashita, Eric

2015-01-01

Honolulu is susceptible to coastal flooding hazards. Like other coastal cities, Honolulu&s long-term economic viability and sustainability depends on how well it can adapt to changes in the natural and built environment. While there is a disagreement over the magnitude and extent of localized impacts associated with climate change, it is widely accepted that by 2100 there will be at least a meter in sea level rise (SLR) and an increase in extreme weather events. Increased exposure and vulnerabilities associated with urbanization and location of human activities in coastal areas warrants serious consideration by planners and policy makers. This article has three objectives. First, flooding due to the combined effects of SLR and episodic hydro-meteorological and geophysical events in Honolulu are investigated and the risks to the community are quantified. Second, the risks and vulnerabilities of critical infrastructure and the surface transportation system are described. Third, using the travel demand software, travel distances and travel times for evacuation from inundated areas are modeled. Data from three inundation models were used. The first model simulated storm surge from a category 4 hurricane similar to Hurricane Iniki which devastated the island of Kauai in 1992. The second model estimates inundation based on five tsunamis that struck Hawaii. A 1-m increase in sea level was included in both the hurricane storm surge and tsunami flooding models. The third model used in this article generated a 500-year flood event due to riverine flooding. Using a uniform grid cell structure, the three inundation maps were used to assess the worst case flooding scenario. Based on the flood depths, the ruling hazard (hurricane, tsunami, or riverine flooding) for each grid cell was determined. The hazard layer was analyzed with socioeconomic data layers to determine the impact on vulnerable populations, economic activity, and critical infrastructure. The analysis focused both on evacuation needs and the critical elements of the infrastructure system that are needed to ensure effective response and recovery in the advent of flooding. This study shows that the coastal flooding will seriously affect the economy and employment. Extreme flooding events could affect 38 percent of the freeways, 44 percent of the highways, 69 percent of the arterial roads, and 40 percent of the local streets in the area examined. Approximately 80 percent of the economy and 76 percent of the total employment in the urban core of Honolulu is exposed to flooding. Evacuation modeling, shelter accessibility, and travel time to shelter analyses revealed that there is a significant shortage in sheltering options, as well as increases in travel times and distances as inundation depth increases. The findings are useful for evacuation and shelter planning for extreme coastal events, as well as for climate change adaptation planning in Honolulu. Recommendations for emergency responders as well as those interested in the integration of long-term SLR and low probability, high consequence coastal hazards are included. The study shows how to integrate travel demand modeling across multiple hazards and threats related to evacuating, sheltering, and disaster risk reduction.

Estimated post-flood effects through Sentinel and Landsat data to support civil protection

NASA Astrophysics Data System (ADS)

Cicala, Luca; Angelino, Cesario Vincenzo; Fiscante, Nicomino; Focareta, Mariano

2016-10-01

On October 15, 2015, a severe and devastating flood hit the region of Sannio, Southern Italy, and the city of Benevento. Benevento and the hilly area of Sannio, have already experienced similar disasters, but the natural disasters occurred in the past did not help to better cope with current ones. The flood in this almost unknown area of Campania reached its climax with the flooding of the Tammaro and Calore rivers. The extent of the damage to the region, businesses and people was very heavy. Benevento is the most affected area. Utilizing a combination of remote-sensing techniques, Geographic Information System (GIS) data, this project employed Sentinel-1/2 and Landsat 8 imagery taken before and during the floods to calculate total inundated area and delineate flood extent. This data was then used to assess pre-existing flood hazard maps of the area. The resulting maps and methodologies from this project were delivered to the local governments and organizations as they work to better understand this historic event and plan for recovery throughout the region. The main goal of this study is to map flood inundation using principally open, free and full data acquired by Sentinel and Landsat satellite platforms operated by European Space Agency (ESA) and the National Aeronautics and Space Administration (NASA) respectively.

The Limit of Inundation of the September 29, 2009, Tsunami on Tutuila, American Samoa

USGS Publications Warehouse

Jaffe, Bruce E.; Gelfenbaum, Guy; Buckley, Mark L.; Watt, Steve; Apotsos, Alex; Stevens, Andrew W.; Richmond, Bruce M.

2010-01-01

U.S. Geological Survey scientists investigated the coastal impacts of the September 29, 2009, South Pacific tsunami in Tutuila, American Samoa in October and November 2009, including mapping the alongshore variation in the limit of inundation. Knowing the inundation limit is useful for planning safer coastal development and evacuation routes for future tsunamis and for improving models of tsunami hazards. This report presents field data documenting the limit of inundation at 18 sites around Tutuila collected in the weeks following the tsunami using Differential GPS (DGPS). In total, 15,703 points along inundation lines were mapped. Estimates of DGPS error and uncertainty in interpretation of the inundation line are provided as electronic files that accompany this report.

Flood pulsing in the Sudd wetland: analysis of seasonal variations in 2 inundation and evapotranspiration in Southern Sudan

USGS Publications Warehouse

Senay, Gabriel B.; Rebelo, L-M.; McCartney, M.P.

2012-01-01

Located on the Bahr el Jebel in South Sudan, the Sudd is one of the largest floodplain wetlands in the world. Seasonal inundation drives the hydrologic, geomorphological, and ecological processes, and the annual flood pulse is essential to the functioning of the Sudd. Despite the importance of the flood pulse, various hydrological interventions are planned upstream of the Sudd to increase economic benefits and food security. These will not be without consequences, in particular for wetlands where the biological productivity, biodiversity, and human livelihoods are dependent on the flood pulse and both the costs and benefits need to be carefully evaluated. Many African countries still lack regional baseline information on the temporal extent, distribution, and characteristics of wetlands, making it hard to assess the consequences of development interventions. Because of political instability in Sudan and the inaccessible nature of the Sudd, recent measurements of flooding and seasonal dynamics are inadequate. Analyses of multitemporal and multisensor remote sensing datasets are presented in this paper, in order to investigate and characterize flood pulsing within the Sudd wetland over a 12-month period. Wetland area has been mapped along with dominant components of open water and flooded vegetation at five time periods over a single year. The total area of flooding (both rain and river fed) over the 12 months was 41 334 km2, with 9176 km2 of this constituting the permanent wetland. Mean annual total evaporation is shown to be higher and with narrower distribution of values from areas of open water (1718 mm) than from flooded vegetation (1641 mm). Although the exact figures require validation against ground-based measurements, the results highlight the relative differences in inundation patterns and evaporation across the Sudd.

Predictions of future ephemeral springtime waterbird stopover habitat availability under global change

USGS Publications Warehouse

Uden, Daniel R.; Allen, Craig R.; Bishop, Andrew A.; Grosse, Roger; Jorgensen, Christopher F.; LaGrange, Theodore G.; Stutheit, Randy G.; Vrtiska, Mark P.

2015-01-01

In the present period of rapid, worldwide change in climate and landuse (i.e., global change), successful biodiversity conservation warrants proactive management responses, especially for long-distance migratory species. However, the development and implementation of management strategies can be impeded by high levels of uncertainty and low levels of control over potentially impactful future events and their effects. Scenario planning and modeling are useful tools for expanding perspectives and informing decisions under these conditions. We coupled scenario planning and statistical modeling to explain and predict playa wetland inundation (i.e., presence/absence of water) and ponded area (i.e., extent of water) in the Rainwater Basin, an anthropogenically altered landscape that provides critical stopover habitat for migratory waterbirds. Inundation and ponded area models for total wetlands, those embedded in rowcrop fields, and those not embedded in rowcrop fields were trained and tested with wetland ponding data from 2004 and 2006–2009, and then used to make additional predictions under two alternative climate change scenarios for the year 2050, yielding a total of six predictive models and 18 prediction sets. Model performance ranged from moderate to good, with inundation models outperforming ponded area models, and models for non-rowcrop-embedded wetlands outperforming models for total wetlands and rowcrop-embedded wetlands. Model predictions indicate that if the temperature and precipitation changes assumed under our climate change scenarios occur, wetland stopover habitat availability in the Rainwater Basin could decrease in the future. The results of this and similar studies could be aggregated to increase knowledge about the potential spatial and temporal distributions of future stopover habitat along migration corridors, and to develop and prioritize multi-scale management actions aimed at mitigating the detrimental effects of global change on migratory waterbird populations.

Adaptation to floods in future climate: a practical approach

NASA Astrophysics Data System (ADS)

Doroszkiewicz, Joanna; Romanowicz, Renata; Radon, Radoslaw; Hisdal, Hege

2016-04-01

In this study some aspects of the application of the 1D hydraulic model are discussed with a focus on its suitability for flood adaptation under future climate conditions. The Biała Tarnowska catchment is used as a case study. A 1D hydraulic model is developed for the evaluation of inundation extent and risk maps in future climatic conditions. We analyse the following flood indices: (i) extent of inundation area; (ii) depth of water on flooded land; (iii) the flood wave duration; (iv) the volume of a flood wave over the threshold value. In this study we derive a model cross-section geometry following the results of primary research based on a 500-year flood inundation extent. We compare two methods of localisation of cross-sections from the point of view of their suitability to the derivation of the most precise inundation outlines. The aim is to specify embankment heights along the river channel that would protect the river valley in the most vulnerable locations under future climatic conditions. We present an experimental design for scenario analysis studies and uncertainty reduction options for future climate projections obtained from the EUROCORDEX project. Acknowledgements: This work was supported by the project CHIHE (Climate Change Impact on Hydrological Extremes), carried out in the Institute of Geophysics Polish Academy of Sciences, funded by Norway Grants (contract No. Pol-Nor/196243/80/2013). The hydro-meteorological observations were provided by the Institute of Meteorology and Water Management (IMGW), Poland.

Urban Infrastructure, Channel-Floodplain Morphology and Flood Flow Patterns

NASA Astrophysics Data System (ADS)

Miller, A. J.; Smith, J. A.; Nelson, C. B.

2006-12-01

The relationship between the channel and the floodplain in urban settings is heavily influenced by (1) altered watershed hydrologic response and frequency distribution of flows, (2) channel enlargement resulting from altered hydrology under conditions of limited sediment supply, (3) direct modification of channels and floodplains for purposes of erosion mitigation, flood protection, commercial development and creation of public amenities, (4) valley constrictions and flow obstructions associated with bridges, culverts, road embankments and other types of floodplain encroachment causing fragmentation or longitudinal segmentation of the riparian corridor. Field observation of inundation patterns associated with recurring floods in the Baltimore metropolitan area is used in combination with 2-dimensional hydraulic modeling to simulate patterns of floodplain inundation and to explore the relationships between magnitude and shape of the flood hydrograph, morphology of the urban channel-floodplain system, and the frequency and extent of floodplain inundation. Case studies include a July 2004 flood associated with a 300-year 2-hour rainfall in a small (14.2 km2) urban watershed, as well as several other events caused by summer thunderstorms with shorter recurrence intervals that generated an extraordinary flood response. The influence of urban infrastructure on flood inundation and flow patterns is expressed in terms of altered (and hysteretic) stage-discharge relationships, stepped flood profiles, rapid longitudinal attenuation of flood waves, and transient flow reversals at confluences and constrictions. Given the current level of interest in restoration measures these patterns merit consideration in planning future development and mitigation efforts.

Development of flood-inundation maps for the West Branch Susquehanna River near the Borough of Jersey Shore, Lycoming County, Pennsylvania

USGS Publications Warehouse

Roland, Mark A.; Hoffman, Scott A.

2011-01-01

Streamflow data, water-surface-elevation profiles derived from a Hydrologic Engineering Center River Analysis System hydraulic model, and geographical information system digital elevation models were used to develop a set of 18 flood-inundation maps for an approximately 5-mile reach of the West Branch Susquehanna River near the Borough of Jersey Shore, Pa. The inundation maps were created by the U.S. Geological Survey in cooperation with the Susquehanna River Basin Commission and Lycoming County as part of an ongoing effort by the National Oceanic and Atmospheric Administration's National Weather Service to focus on continued improvements to the flood forecasting and warning abilities in the Susquehanna River Basin and to modernize flood-forecasting methodologies. The maps, ranging from 23.0 to 40.0 feet in 1-foot increments, correspond to river stage at the U.S. Geological Survey streamgage 01549760 at Jersey Shore. The electronic files used to develop the maps were provided to the National Weather Service for incorporation into their Advanced Hydrologic Prediction Service website. The maps are displayed on this website, which serves as a web-based floodwarning system, and can be used to identify areas of predicted flood inundation associated with forecasted flood-peak stages. During times of flooding or predicted flooding, these maps can be used by emergency managers and the public to take proactive steps to protect life and reduce property damage caused by floods.

A simple inertial formulation of the shallow water equations for efficient two-dimensional flood inundation modelling

NASA Astrophysics Data System (ADS)

Bates, Paul D.; Horritt, Matthew S.; Fewtrell, Timothy J.

2010-06-01

SummaryThis paper describes the development of a new set of equations derived from 1D shallow water theory for use in 2D storage cell inundation models where flows in the x and y Cartesian directions are decoupled. The new equation set is designed to be solved explicitly at very low computational cost, and is here tested against a suite of four test cases of increasing complexity. In each case the predicted water depths compare favourably to analytical solutions or to simulation results from the diffusive storage cell code of Hunter et al. (2005). For the most complex test involving the fine spatial resolution simulation of flow in a topographically complex urban area the Root Mean Squared Difference between the new formulation and the model of Hunter et al. is ˜1 cm. However, unlike diffusive storage cell codes where the stable time step scales with (1/Δ x) 2, the new equation set developed here represents shallow water wave propagation and so the stability is controlled by the Courant-Freidrichs-Lewy condition such that the stable time step instead scales with 1/Δ x. This allows use of a stable time step that is 1-3 orders of magnitude greater for typical cell sizes than that possible with diffusive storage cell models and results in commensurate reductions in model run times. For the tests reported in this paper the maximum speed up achieved over a diffusive storage cell model was 1120×, although the actual value seen will depend on model resolution and water surface gradient. Solutions using the new equation set are shown to be grid-independent for the conditions considered and to have an intuitively correct sensitivity to friction, however small instabilities and increased errors on predicted depth were noted when Manning's n = 0.01. The new equations are likely to find widespread application in many types of flood inundation modelling and should provide a useful additional tool, alongside more established model formulations, for a variety of flood risk management studies.

Modeling spatiotemporal dynamics of global wetlands: comprehensive evaluation of a new sub-grid TOPMODEL parameterization and uncertainties

NASA Astrophysics Data System (ADS)

Zhang, Zhen; Zimmermann, Niklaus E.; Kaplan, Jed O.; Poulter, Benjamin

2016-03-01

Simulations of the spatiotemporal dynamics of wetlands are key to understanding the role of wetland biogeochemistry under past and future climate. Hydrologic inundation models, such as the TOPography-based hydrological model (TOPMODEL), are based on a fundamental parameter known as the compound topographic index (CTI) and offer a computationally cost-efficient approach to simulate wetland dynamics at global scales. However, there remains a large discrepancy in the implementations of TOPMODEL in land-surface models (LSMs) and thus their performance against observations. This study describes new improvements to TOPMODEL implementation and estimates of global wetland dynamics using the LPJ-wsl (Lund-Potsdam-Jena Wald Schnee und Landschaft version) Dynamic Global Vegetation Model (DGVM) and quantifies uncertainties by comparing three digital elevation model (DEM) products (HYDRO1k, GMTED, and HydroSHEDS) at different spatial resolution and accuracy on simulated inundation dynamics. In addition, we found that calibrating TOPMODEL with a benchmark wetland data set can help to successfully delineate the seasonal and interannual variation of wetlands, as well as improve the spatial distribution of wetlands to be consistent with inventories. The HydroSHEDS DEM, using a river-basin scheme for aggregating the CTI, shows the best accuracy for capturing the spatiotemporal dynamics of wetlands among the three DEM products. The estimate of global wetland potential/maximum is ˜ 10.3 Mkm2 (106 km2), with a mean annual maximum of ˜ 5.17 Mkm2 for 1980-2010. When integrated with wetland methane emission submodule, the uncertainty of global annual CH4 emissions from topography inputs is estimated to be 29.0 Tg yr-1. This study demonstrates the feasibility of TOPMODEL to capture spatial heterogeneity of inundation at a large scale and highlights the significance of correcting maximum wetland extent to improve modeling of interannual variations in wetland area. It additionally highlights the importance of an adequate investigation of topographic indices for simulating global wetlands and shows the opportunity to converge wetland estimates across LSMs by identifying the uncertainty associated with existing wetland products.

Remote Sensing for Hydrology: Surface Water Dynamics from Three Decades of Landsat Data

NASA Astrophysics Data System (ADS)

Tulbure, M. G.; Broich, M.; Kingsford, R.; Lucas, R.; Keith, D.

2014-12-01

Surface water is a vital resource affected by changes in climate and anthropogenic factors. Knowledge of surface water dynamics provides critical information for flood and drought management. Here we focused on the on the entire Murray-Darling Basin (MDB) of Australia, a large semi-arid region with scarce water resources, high hydroclimatic variability and competing water demands, impacted by climate change, altered flow regimes and land use changes. The MDB is also an area where substantial investment in environmental water allocation of large volumes of environmental flow was made. We used Landsat TM and ETM+ time series to synoptically map the dynamic of surface water extent with an internally consistent algorithm (Tulbure and Broich, 2013) over decades (1986-2011). We used a subset of Landsat path/rows for image training in both wet and dry years. Results show high interannual variability in number and size of flooded areas, with flooded areas during the Millennium Drought (until 2009) being substantially smaller than during the excessive 2010-2011 La Nina flooding. Flooding frequency in 2006, a very dry year was lower than in 2010, the La Nina year when extensive floods occurred. More developed areas of the basin showed different inter-annual patterns from natural areas of the basin. At Barmah-Millewa, the largest river red gum forest in the world, we also mapped flooded forest and tracked changes in NDVI. Higher NDVI values were found in areas more frequently flooded. Knowledge of the spatial and temporal dynamics of flooding and the response of riparian vegetation communities to flooding is important for management of floodplain wetlands and vegetation communities and for investigating effectiveness of environmental flows and flow regimes in the MDB. Existing maps of inundated areas are linked with river flow to quantify the relationship between river flow and inundated area in the MDB. Historic flood inundation extent mapped via remote sensing can be used to quantify spatially explicit changes in surface water dynamics and vegetation communities as outcomes of management scenarios in response to water management decisions. This methodology is globally applicable and relevant to areas prone to flooding with competing water demands and can be used for mapping water availability in data scarce regions.

Vulnerability of Northeastern U.S. Salt Marshes to Climatic and Anthropogenic Stressors

EPA Science Inventory

In the Northeastern U.S., salt marsh area is in decline. Habitat change analysis has revealed fragmentation, displacement of high marsh by low marsh species, and marsh drowning, while development of adjacent uplands limits upslope migration. Using inundation experiments, field s...

Vulnerability of Northeastern U.S. Salt Marshes to Climatic and Anthropogenic Stressors (AGU)

EPA Science Inventory

In the Northeastern U.S., salt marsh area is in decline. Habitat change analysis has revealed fragmentation, displacement of high marsh by low marsh species, and ecological drowning, while development of adjacent uplands limits upslope migration. Using inundation experiments, fi...

Development of a decision support system for tsunami evacuation: application to the Jiyang District of Sanya city in China

NASA Astrophysics Data System (ADS)

Hou, Jingming; Yuan, Ye; Wang, Peitao; Ren, Zhiyuan; Li, Xiaojuan

2017-03-01

Major tsunami disasters often cause great damage in the first few hours following an earthquake. The possible severity of such events requires preparations to prevent tsunami disasters or mitigate them. This paper is an attempt to develop a decision support system for rapid tsunami evacuation for local decision makers. Based on the numerical results database of tsunami disasters, this system can quickly obtain the tsunami inundation and travel time. Because numerical models are calculated in advance, this system can reduce decision-making time. Population distribution, as a vulnerability factor, was analyzed to identify areas of high risk for tsunami disasters. Combined with spatial data, this system can comprehensively analyze the dynamic and static evacuation process and identify problems that negatively impact evacuation, thus supporting the decision-making for tsunami evacuation in high-risk areas. When an earthquake and tsunami occur, this system can rapidly obtain the tsunami inundation and travel time and provide information to assist with tsunami evacuation operations.

Real-time tsunami inundation forecasting and damage mapping towards enhancing tsunami disaster resiliency

NASA Astrophysics Data System (ADS)

Koshimura, S.; Hino, R.; Ohta, Y.; Kobayashi, H.; Musa, A.; Murashima, Y.

2014-12-01

With use of modern computing power and advanced sensor networks, a project is underway to establish a new system of real-time tsunami inundation forecasting, damage estimation and mapping to enhance society's resilience in the aftermath of major tsunami disaster. The system consists of fusion of real-time crustal deformation monitoring/fault model estimation by Ohta et al. (2012), high-performance real-time tsunami propagation/inundation modeling with NEC's vector supercomputer SX-ACE, damage/loss estimation models (Koshimura et al., 2013), and geo-informatics. After a major (near field) earthquake is triggered, the first response of the system is to identify the tsunami source model by applying RAPiD Algorithm (Ohta et al., 2012) to observed RTK-GPS time series at GEONET sites in Japan. As performed in the data obtained during the 2011 Tohoku event, we assume less than 10 minutes as the acquisition time of the source model. Given the tsunami source, the system moves on to running tsunami propagation and inundation model which was optimized on the vector supercomputer SX-ACE to acquire the estimation of time series of tsunami at offshore/coastal tide gauges to determine tsunami travel and arrival time, extent of inundation zone, maximum flow depth distribution. The implemented tsunami numerical model is based on the non-linear shallow-water equations discretized by finite difference method. The merged bathymetry and topography grids are prepared with 10 m resolution to better estimate the tsunami inland penetration. Given the maximum flow depth distribution, the system performs GIS analysis to determine the numbers of exposed population and structures using census data, then estimates the numbers of potential death and damaged structures by applying tsunami fragility curve (Koshimura et al., 2013). Since the tsunami source model is determined, the model is supposed to complete the estimation within 10 minutes. The results are disseminated as mapping products to responders and stakeholders, e.g. national and regional municipalities, to be utilized for their emergency/response activities. In 2014, the system is verified through the case studies of 2011 Tohoku event and potential earthquake scenarios along Nankai Trough with regard to its capability and robustness.

Flood-hazard mapping in Honduras in response to Hurricane Mitch

USGS Publications Warehouse

Mastin, M.C.

2002-01-01

The devastation in Honduras due to flooding from Hurricane Mitch in 1998 prompted the U.S. Agency for International Development, through the U.S. Geological Survey, to develop a country-wide systematic approach of flood-hazard mapping and a demonstration of the method at selected sites as part of a reconstruction effort. The design discharge chosen for flood-hazard mapping was the flood with an average return interval of 50 years, and this selection was based on discussions with the U.S. Agency for International Development and the Honduran Public Works and Transportation Ministry. A regression equation for estimating the 50-year flood discharge using drainage area and annual precipitation as the explanatory variables was developed, based on data from 34 long-term gaging sites. This equation, which has a standard error of prediction of 71.3 percent, was used in a geographic information system to estimate the 50-year flood discharge at any location for any river in the country. The flood-hazard mapping method was demonstrated at 15 selected municipalities. High-resolution digital-elevation models of the floodplain were obtained using an airborne laser-terrain mapping system. Field verification of the digital elevation models showed that the digital-elevation models had mean absolute errors ranging from -0.57 to 0.14 meter in the vertical dimension. From these models, water-surface elevation cross sections were obtained and used in a numerical, one-dimensional, steady-flow stepbackwater model to estimate water-surface profiles corresponding to the 50-year flood discharge. From these water-surface profiles, maps of area and depth of inundation were created at the 13 of the 15 selected municipalities. At La Lima only, the area and depth of inundation of the channel capacity in the city was mapped. At Santa Rose de Aguan, no numerical model was created. The 50-year flood and the maps of area and depth of inundation are based on the estimated 50-year storm tide.

Coastal flooding hazard related to storms and coastal evolution in Valdelagrana spit (Cadiz Bay Natural Park, SW Spain)

NASA Astrophysics Data System (ADS)

Benavente, J.; Del Río, L.; Gracia, F. J.; Martínez-del-Pozo, J. A.

2006-06-01

Mapping of coastal inundation hazard related to storms requires the combination of multiple sources of information regarding meteorological, morphological and dynamic characteristics of both the area at risk and the studied phenomena. Variables such as beach slope, storm wave height or wind speed have traditionally been used, but detailed geomorphological features of the area as well as long-term shoreline evolution trends must also be taken into account in order to achieve more realistic results. This work presents an evaluation of storm flooding hazard in Valdelagrana spit and marshes (SW Spain), considering two types of storm that are characteristic of the area: a modal storm with 1 year of recurrence interval (maximum wave height of 3.3 m), and an extreme storm with 6-10 years of recurrence interval (maximum wave height of 10.6 m), both approaching the coast perpendicularly. After calculating theoretical storm surge elevation, a digital terrain model was made by adjusting topographic data to field work and detailed geomorphological analysis. A model of flooding extent was subsequently developed for each storm type, and then corrected according to the rates of shoreline change in the last decades, which were assessed by means of aerial photographs taking the dune toe as shoreline indicator. Results show that long-term coastline trend represents an important factor in the prediction of flooding extent, since shoreline retreat causes the deterioration of natural coastal defences as dune ridges, thus increasing coastal exposure to high-energy waves. This way, it has been stated that the lack of sedimentary supply plays an important role in spatial variability of inundation extent in Valdelagrana spit. Finally, a hazard map is presented, where calculated coastal retreat rates are employed in order to predict the areas that could be affected by future inundation events.

Quantifying Uncertainty in Flood Inundation Mapping Using Streamflow Ensembles and Multiple Hydraulic Modeling Techniques

NASA Astrophysics Data System (ADS)

Hosseiny, S. M. H.; Zarzar, C.; Gomez, M.; Siddique, R.; Smith, V.; Mejia, A.; Demir, I.

2016-12-01

The National Water Model (NWM) provides a platform for operationalize nationwide flood inundation forecasting and mapping. The ability to model flood inundation on a national scale will provide invaluable information to decision makers and local emergency officials. Often, forecast products use deterministic model output to provide a visual representation of a single inundation scenario, which is subject to uncertainty from various sources. While this provides a straightforward representation of the potential inundation, the inherent uncertainty associated with the model output should be considered to optimize this tool for decision making support. The goal of this study is to produce ensembles of future flood inundation conditions (i.e. extent, depth, and velocity) to spatially quantify and visually assess uncertainties associated with the predicted flood inundation maps. The setting for this study is located in a highly urbanized watershed along the Darby Creek in Pennsylvania. A forecasting framework coupling the NWM with multiple hydraulic models was developed to produce a suite ensembles of future flood inundation predictions. Time lagged ensembles from the NWM short range forecasts were used to account for uncertainty associated with the hydrologic forecasts. The forecasts from the NWM were input to iRIC and HEC-RAS two-dimensional software packages, from which water extent, depth, and flow velocity were output. Quantifying the agreement between output ensembles for each forecast grid provided the uncertainty metrics for predicted flood water inundation extent, depth, and flow velocity. For visualization, a series of flood maps that display flood extent, water depth, and flow velocity along with the underlying uncertainty associated with each of the forecasted variables were produced. The results from this study demonstrate the potential to incorporate and visualize model uncertainties in flood inundation maps in order to identify the high flood risk zones.

Eggshell structure in Caiman latirostris eggs improves embryo survival during nest inundation.

PubMed

Cedillo-Leal, César; Simoncini, Melina S; Leiva, Pamela M L; Larriera, Alejandro; Lang, Jeffrey W; Piña, Carlos I

2017-05-17

Egg inundation often results in poor hatching success in crocodylians. However, how tolerant eggs are to submergence, and/or how eggshell ultrastructure may affect embryo survival when inundated, are not well understood. In this study, our objective was to determine if embryo survival in Caiman latirostris is affected by eggshell surface roughness, when eggs are submerged under water. Tolerance to inundation was tested early (day 30) versus late (day 60) in development, using eight clutches (four per time treatments), subdivided into four groups: ( N = 9 per clutch per treatment; 9 × 4 = 36 eggs per group). 'Rough' eggshell represented the natural, unmodified eggshell surface structure. 'Smooth' eggshell surface structure was created by mechanically sanding the natural rough surface to remove surface columnar elements and secondary layer features, e.g. irregularities that result in 'roughness'. When inundated by submerging eggs under water for 10 h at day 30, 'smooth' eggshell structure resulted in more than twice as many dead embryos (16 versus 6, smooth versus rough; N = 36), and fewer than half as many healthy embryos (6 versus 13, smooth versus rough, respectively; N = 36). By contrast, at day 60, inundation resulted in very low hatching success, regardless of eggshell surface structure. Only two hatchlings survived the inundation, notably in the untreated group with intact, rough eggshells. Inundation produced a high rate of malformations (58% at day 30), but did not affect hatchling size. Our results indicate that eggshell roughness enhances embryo survival when eggs are inundated early in development, but not late in development. Apparently, the natural surface 'roughness' entraps air bubbles at the eggshell surface during inundation, thereby facilitating gas exchange through the eggshell even when the egg is submerged under water. © 2017 The Author(s).

Assessing the Impacts of Coastal Erosion, Passive Inundation, and Dynamic Wave Inundation under Higher Sea Level in Hawaii

NASA Astrophysics Data System (ADS)

Fletcher, C. H., II; Anderson, T. R.; Barbee, M.

2016-02-01

The Interagency Climate Adaptation Committee was created by the Hawaii Legislature and Act 83 to investigate community vulnerability to sea level rise (SLR) in Hawaii. To support the committee, we model: (1) coastal erosion; (2) wave inundation; and (3) passive flooding based on the IPCC RCP 8.5 model of SLR over the 21st Century. Erosion is estimated using a hybrid equilibrium profile model (Anderson et al., 2015) that combines historical rates of shoreline change with a Bruun-type model of beach profile adjustment to SLR. Results are mapped to GIS layers showing the 80th-percentile probability of potential shoreline change at years 2030, 2050, 2075, and 2100. Seasonal wave inundation is modeled using XBeach (Deltares) in non-hydrostatic mode. A seasonal high wave event (Ho=2.3 m, Tp=16 s, Dir=200° for the Ewa test site) is simulated at each heightened sea level (corresponding to the years previously mentioned); which accounts for changes in wave dynamics due to the change in water level over the reef platform. We use a bare earth topo/bathy digital elevation model derived from USACE 2013 LIDAR data surveys and multi-beam and side-scan sonar data from the Hawaii Mapping Research Group at the University of Hawaii. Waves are modeled along one-dimensional profiles spaced 20 m apart. From this, we develop a gridded product of water depth and velocity for use in a vulnerability analysis. Passive flooding due to SLR, the so-called "bath tub" method, is used as a proxy for groundwater inundation of low-lying coastal plains (where the majority of development in Hawaii takes place). Modeling results are used with other available data in the FEMA Hazus software to estimate exposure and loss of upland assets. Here, we present the three modeling products and a summary of the larger hazard assessment for the Ewa area on the Hawaiian Island of Oahu.

Mapping global surface water inundation dynamics using synergistic information from SMAP, AMSR2 and Landsat

NASA Astrophysics Data System (ADS)

Du, J.; Kimball, J. S.; Galantowicz, J. F.; Kim, S.; Chan, S.; Reichle, R. H.; Jones, L. A.; Watts, J. D.

2017-12-01

A method to monitor global land surface water (fw) inundation dynamics was developed by exploiting the enhanced fw sensitivity of L-band (1.4 GHz) passive microwave observations from the Soil Moisture Active Passive (SMAP) mission. The L-band fw (fwLBand) retrievals were derived using SMAP H-polarization brightness temperature (Tb) observations and predefined L-band reference microwave emissivities for water and land endmembers. Potential soil moisture and vegetation contributions to the microwave signal were represented from overlapping higher frequency Tb observations from AMSR2. The resulting fwLBand global record has high temporal sampling (1-3 days) and 36-km spatial resolution. The fwLBand annual averages corresponded favourably (R=0.84, p<0.001) with a 250-m resolution static global water map (MOD44W) aggregated at the same spatial scale, while capturing significant inundation variations worldwide. The monthly fwLBand averages also showed seasonal inundation changes consistent with river discharge records within six major US river basins. An uncertainty analysis indicated generally reliable fwLBand performance for major land cover areas and under low to moderate vegetation cover, but with lower accuracy for detecting water bodies covered by dense vegetation. Finer resolution (30-m) fwLBand results were obtained for three sub-regions in North America using an empirical downscaling approach and ancillary global Water Occurrence Dataset (WOD) derived from the historical Landsat record. The resulting 30-m fwLBand retrievals showed favourable classification accuracy for water (commission error 31.84%; omission error 28.08%) and land (commission error 0.82%; omission error 0.99%) and seasonal wet and dry periods when compared to independent water maps derived from Landsat-8 imagery. The new fwLBand algorithms and continuing SMAP and AMSR2 operations provide for near real-time, multi-scale monitoring of global surface water inundation dynamics, potentially benefiting hydrological monitoring, flood assessments, and global climate and carbon modeling.

40 CFR 230.43 - Vegetated shallows.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Vegetated shallows. 230.43 Section 230... Special Aquatic Sites § 230.43 Vegetated shallows. (a) Vegetated shallows are permanently inundated areas... reducing light penetration and hence photosynthesis; and (5) changing the capacity of a vegetated shallow...

40 CFR 257.3-1 - Floodplains.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Floodplains. 257.3-1 Section 257.3-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR... coastal waters, including flood-prone areas of offshore islands, which are inundated by the base flood. (3...

40 CFR 257.3-1 - Floodplains.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Floodplains. 257.3-1 Section 257.3-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR... coastal waters, including flood-prone areas of offshore islands, which are inundated by the base flood. (3...

40 CFR 257.3-1 - Floodplains.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 26 2013-07-01 2013-07-01 false Floodplains. 257.3-1 Section 257.3-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR... coastal waters, including flood-prone areas of offshore islands, which are inundated by the base flood. (3...

40 CFR 257.3-1 - Floodplains.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Floodplains. 257.3-1 Section 257.3-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR... coastal waters, including flood-prone areas of offshore islands, which are inundated by the base flood. (3...

40 CFR 257.3-1 - Floodplains.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Floodplains. 257.3-1 Section 257.3-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR... coastal waters, including flood-prone areas of offshore islands, which are inundated by the base flood. (3...

28 CFR 63.4 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.4... buildings, including mobile homes and gas or liquid storage tanks that are primarily above ground (as set by the NFIP). (s) Wetlands—“those areas that are inundated by surface or ground water with a frequency...

Determination of Flood Reduction Alternatives for Climate Change Adaptation in Gyeongancheon basin

NASA Astrophysics Data System (ADS)

Han, D.; Joo, H. J.; Jung, J.; Kim, H. S.

2017-12-01

Recently, the frequency of extreme rainfall event has increased due to the climate change and the impermeable area in an urban watershed has also increased due to the rapid urbanization. Therefore, the flood risk is increasing and we ought to prepare countermeasures for flood damage reduction. For the determination of appropriate measures or alternatives, firstly, this study estimated the frequency based rainfall considering the climate change according to the each target period(reference : 1971˜2010, Target period Ⅰ : 2011˜2040, Target period Ⅱ : 2041˜2070, Target period Ⅲ : 2071˜2100). Then the future flood discharge was computed by using HEC-HMS model. We set 5 sizes of drainage pumps and detention ponds respectively as the flood reduction alternatives and the flood level in the river was obtained by each alternative through HEC-RAS model. The flood inundation map was constructed using topographical data and flood water level in the river and the economic analysis was conducted for the flood damage reduction studies using Multi Dimensional Flood Damage Analysis (MD-FDA) tool. As a result of the effectiveness analysis of the flood reduction alternatives, the flood level by drainage pump was reduced by 0.06m up to 0.44m while it was reduced by 0.01m up to 1.86m in the case of the detention pond. The flooded area was shrunk by up to 32.64% from 0.3% and inundation depth was also dropped. As a result of a comparison of the Benefit/Cost ratio estimated by the economic analysis, a detention pond E in the target period Ⅰ and the pump D in the periods Ⅱ and Ⅲ were considered as the appropriate alternatives for the flood damage reduction under the climate change. AcknowledgementsThis research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Science, ICT & Future Planning(2017R1A2B3005695)

Is There Ecological Information in Optical Polarization Data?

NASA Technical Reports Server (NTRS)

Vanderbilt, Vern; Daughtry, Craig; Dahlgren, Robert

2015-01-01

Optical linear polarization? In remote sensing it's due to specular reflection. The first surface that incident light encounters - a smooth water surface or the waxy first surface of a leaf's cuticle, if it's even somewhat smooth (i.e. shiny) - will specularly reflect and linearly polarize the incident light. We provide three examples of the types of ecological information contained in remotely sensed optical linear polarization measurements. Remove the surface reflection to better see the interior. The linearly polarized light reflected by leaf surfaces contains no information about cellular pigments, metabolites, or water contained in the leaf interiors of a plant canopy, because it never enters the leaf interior to interact with them. Thus, for purposes of remotely sensing the leaf interiors of a plant canopy, the linearly polarized light should be subtracted from the total reflected light, because including it would add noise to the measurement. In particular 'minus specular' vegetation indices should allow improved monitoring of a plant canopy's physiological processes. Estimate plant development stage and yield. Wheat and sorghum grain heads, following emergence, rapidly extend upward and very quickly tower over nearby leaves, partially blocking our view of the sunlight reflected by those leaf surfaces. The resulting decrease in the amount of surface reflected and polarized sunlight, if monitored over time, potentially allows per-field estimates of the dates of the heading and flowering development stages to be interleaved with weather data in models, which is key to better estimating per-field grain yield. Similar polarization changes may occur in other grasses, such as oats, barley, corn and rice, each a crop so widely grown that it potentially affects climate at the regional scale. Wetlands Mapping. The sunlight specularly reflected by surface waters is blindingly bright, spectrally flat and polarized - all of which telegraphs that the ground area is inundated. Inundated soils exchange methane with the atmosphere; non-inundated soils, carbon dioxide. Aquatic plants growing through the water surface pipe the soil-produced methane via the stomata to the atmosphere, enhancing exchanges rates by factors of 10-20 compared to ebullition (bubbling) or diffusion through the water column to the atmosphere. Thus, mapping wetland areas into three community types - inundated areas with emergent vegetation, open water and uplands - provides potentially key information to water, carbon and energy budgets at landscape to global scales.

A first computational framework for integrated hydrologic-hydrodynamic inundation modelling

NASA Astrophysics Data System (ADS)

Hoch, Jannis; Baart, Fedor; Neal, Jeffrey; van Beek, Rens; Winsemius, Hessel; Bates, Paul; Bierkens, Marc

2017-04-01

To provide detailed flood hazard and risk estimates for current and future conditions, advanced modelling approaches are required. Currently, many approaches are however built upon specific hydrologic or hydrodynamic model routines. By applying these routines in stand-alone mode important processes cannot accurately be described. For instance, global hydrologic models (GHM) run at coarse spatial resolution which does not identify locally relevant flood hazard information. Moreover, hydrologic models generally focus on correct computations of water balances, but employ less sophisticated routing schemes such as the kinematic wave approximation. Hydrodynamic models, on the other side, excel in the computations of open water flow dynamics, but are highly dependent on specific runoff or observed discharge for their input. In most cases hydrodynamic models are forced by applying discharge at the boundaries and thus cannot account for water sources within the model domain. Thus, discharge and inundation dynamics at reaches not fed by upstream boundaries cannot be modelled. In a recent study, Hoch et al. (HESS, 2017) coupled the GHM PCR-GLOBWB with the hydrodynamic model Delft3D Flexible Mesh. A core element of this study was that both models were connected on a cell-by-cell basis which allows for direct hydrologic forcing within the hydrodynamic model domain. The means for such model coupling is the Basic Model Interface (BMI) which provides a set of functions to directly access model variables. Model results showed that discharge simulations can profit from model coupling as their accuracy is higher compared to stand-alone runs. Model results of a coupled simulation clearly depend on the quality of the individual models. Depending on purpose, location or simply the models at hand, it would be worthwhile to allow a wider range of models to be coupled. As a first step, we present a framework which allows coupling of PCR-GLOBWB to both Delft3D Flexible Mesh and LISFLOOD-FP. The coupling framework consists of a main script and a set of functions performing the actual model coupling as well as data processing. All that is required therefore are model schematizations of the models involved for the domain of interest. It is noteworthy that no adaptions to already existing schematizations have to be made. Within the framework, it is possible to distribute input volume from PCR-GLOBWB over the 2D hydrodynamic grid ("2D option"), or if available, directly into the 1D channels ("1D option"). Besides, it is possible to input the water volumes into the hydrodynamic models either as fluxes or states. With PCR-GLOBWB being a global model, it is possible to apply the coupling scheme anywhere, which reduces the dependency of observation data for discharge boundaries. Reducing this dependency is of particular benefit for areas where only a limited number of accurate measurements are available. First results of applying the coupling framework show that differences between both hydrodynamic models are mainly apparent in the timing of peak discharge when using the 1D option. Regarding inundation extent, applying LISFLOOD-FP with a regular grid outperforms the flexible mesh of Delft3D for those areas where a coarser spatial resolution is used in the flexible mesh. When using the 2D option, however, using Delft3D Flexible Mesh is more robust than LISFLOOD-FP due to the differences in the solver used in the models. With Delft3D Flexible Mesh solving the full Saint-Vernant equations, and LISFLOOD-FP solving the local inertial wave approximation which lacks the convective acceleration term, the framework hence allows for choosing the hydrodynamic parts based on the local characteristics of a chosen study area.

Hydraulic model and flood-inundation maps developed for the Pee Dee National Wildlife Refuge, North Carolina

USGS Publications Warehouse

Smith, Douglas G.; Wagner, Chad R.

2016-04-08

A series of digital flood-inundation maps were developed on the basis of the water-surface profiles produced by the model. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Program Web site at http://water.usgs.gov/osw/flood_inundation, depict estimates of the areal extent and depth of flooding corresponding to selected water levels at the USGS streamgage Pee Dee River at Pee Dee Refuge near Ansonville, N.C. These maps, when combined with real-time water-level information from USGS streamgages, provide managers with critical information to help plan flood-response activities and resource protection efforts.

Flood-inundation map and water-surface profiles for floods of selected recurrence intervals, Consumnes River and Deer Creek, Sacramento County, California

USGS Publications Warehouse

Guay, Joel R.; Harmon, Jerry G.; McPherson, Kelly R.

1998-01-01

The damage caused by the January 1997 floods along the Cosumnes River and Deer Creek generated new interest in planning and managing land use in the study area. The 1997 floodflow peak, the highest on record and considered to be a 150-year flood, caused levee failures at 24 locations. In order to provide a technical basis for floodplain management practices, the U.S. Goelogical Survey, in cooperation with the Federal Emergency Management Agency, completed a flood-inundation map of the Cosumnes River and Deer Creek drainage from Dillard Road bridge to State Highway 99. Flood frequency was estimated from streamflow records for the Cosumnes River at Michigan Bar and Deer Creek near Sloughhouse. Cross sections along a study reach, where the two rivers generally flow parallel to one another, were used with a step-backwater model (WSPRO) to estimate the water-surface profile for floods of selected recurrence intervals. A flood-inundation map was developed to show flood boundaries for the 100-year flood. Water-surface profiles were developed for the 5-, 10-, 50-, 100-, and 500-year floods.

Mapping hurricane rita inland storm tide

USGS Publications Warehouse

Berenbrock, C.; Mason, R.R.; Blanchard, S.F.

2009-01-01

Flood-inundation data are most useful for decision makers when presented in the context of maps of affected communities and (or) areas. But because the data are scarce and rarely cover the full extent of the flooding, interpolation and extrapolation of the information are needed. Many geographic information systems provide various interpolation tools, but these tools often ignore the effects of the topographic and hydraulic features that influence flooding. A barrier mapping method was developed to improve maps of storm tide produced by Hurricane Rita. Maps were developed for the maximum storm tide and at 3-h intervals from midnight (00:00 hours) through noon (12:00 hours) on 24 September 2005. The improved maps depict storm-tide elevations and the extent of flooding. The extent of storm-tide inundation from the improved maximum storm-tide map was compared with the extent of flood inundation from a map prepared by the Federal Emergency Management Agency (FEMA). The boundaries from these two maps generally compared quite well especially along the Calcasieu River. Also a cross-section profile that parallels the Louisiana coast was developed from the maximum storm-tide map and included FEMA high-water marks. ?? 2009 Blackwell Publishing Ltd.

Mapping Hurricane Rita inland storm tide

USGS Publications Warehouse

Berenbrock, Charles; Mason, Jr., Robert R.; Blanchard, Stephen F.; Simonovic, Slobodan P.

2009-01-01

Flood-inundation data are most useful for decision makers when presented in the context of maps of effected communities and (or) areas. But because the data are scarce and rarely cover the full extent of the flooding, interpolation and extrapolation of the information are needed. Many geographic information systems (GIS) provide various interpolation tools, but these tools often ignore the effects of the topographic and hydraulic features that influence flooding. A barrier mapping method was developed to improve maps of storm tide produced by Hurricane Rita. Maps were developed for the maximum storm tide and at 3-hour intervals from midnight (0000 hour) through noon (1200 hour) on September 24, 2005. The improved maps depict storm-tide elevations and the extent of flooding. The extent of storm-tide inundation from the improved maximum storm-tide map was compared to the extent of flood-inundation from a map prepared by the Federal Emergency Management Agency (FEMA). The boundaries from these two maps generally compared quite well especially along the Calcasieu River. Also a cross-section profile that parallels the Louisiana coast was developed from the maximum storm-tide map and included FEMA high-water marks.