Embedded sensor systems for health - providing the tools in future healthcare.

PubMed

Lindén, Maria; Björkman, Mats

2014-01-01

Wearable, embedded sensor systems for health applications are foreseen to be enablers in the future healthcare. They will provide ubiquitous monitoring of multiple parameters without restricting the person to stay at home or in the hospital. By following trend changes in the health status, early deteriorations will be detected and treatment can start earlier. Also health prevention will be supported. Such future healthcare requires technology development, including miniaturized sensors, smart textiles and wireless communication. The tremendous amount of data generated by these systems calls for both signal processing and decision support to guarantee the quality of data and avoid overflow of information. Safe and secure communications have to protect the integrity of the persons monitored.

Difference of motor overflow depending on the impaired or unimpaired hand in stroke patients.

PubMed

Kim, Yushin; Kim, Woo-Sub; Shim, Jae Kun; Suh, Dong Won; Kim, TaeYeong; Yoon, BumChul

2015-02-01

The aim of this study was to investigate the patterns of contralateral motor overflow (i.e. mirror movement) between the homologous body parts on the right and left side, in stroke patients during single-finger and multi-finger maximum force production tasks. Forty subjects, including stroke (n=20) and normal subjects (n=20), participated in this study. The stroke subjects maximally pressed force sensors with their fingers in a flexed position using a single (index, middle, ring, or little) or all fingers (all 4 fingers) using the impaired (IH) or unimpaired (UIH) hand, while the non-patient subjects used their right hands for the same tasks. The maximal voluntary forces in the ipsilateral and unintended pressing forces of each contralateral finger were recorded during the tasks. The magnitude of motor overflow to the contralateral side was calculated using the index of contralateral independence (CI). During the single finger tasks, the finger CI was significantly decreased in the UIH (91%) compared with that in the IH (99%) or normal hands (99%). Likewise, the multiple finger tasks showed that the CI was significantly lower in the UIH (84%) compared with that in the IH (96%) or normal hands (99%). However, the maximal forces were significantly lower in the IH relative to those in the UIH and normal hands. These data demonstrate that stroke patients have greater motor overflow from the UIH to the IH. Copyright © 2014 Elsevier B.V. All rights reserved.

A software-based sensor for combined sewer overflows.

PubMed

Leonhardt, G; Fach, S; Engelhard, C; Kinzel, H; Rauch, W

2012-01-01

A new methodology for online estimation of excess flow from combined sewer overflow (CSO) structures based on simulation models is presented. If sufficient flow and water level data from the sewer system is available, no rainfall data are needed to run the model. An inverse rainfall-runoff model was developed to simulate net rainfall based on flow and water level data. Excess flow at all CSO structures in a catchment can then be simulated with a rainfall-runoff model. The method is applied to a case study and results show that the inverse rainfall-runoff model can be used instead of missing rain gauges. Online operation is ensured by software providing an interface to the SCADA-system of the operator and controlling the model. A water quality model could be included to simulate also pollutant concentrations in the excess flow.

Channel overflows of the Pōhue Bay flow, Mauna Loa, Hawai'i: examples of the contrast between surface and interior lava

NASA Astrophysics Data System (ADS)

Jurado-Chichay, Zinzuni; Rowland, Scott K.

1995-04-01

A number of overflows from a large lava channel and tube system on the southwest rift zone of Mauna Loa were studied. Initial overflows were very low viscosity gas-rich pāhoehoe evidenced by flow-unit aspect ratios and vesicle sizes and contents. Calculated volumetric flow-rates in the channel range between 80 and 890 m3/s, and those of the overflows between 35 and 110 m3/s. After traveling tens to hundreds of meters the tops of these sheet-like overflows were disrupted into a surface composed of clinker and pāhoehoe fragments. After these 'a'ā overflows came to rest, lava from the interiors was able to break out on to the surface as pāhoehoe. The surface structure of a lava flow records the interaction between the differential shear rate (usually correlated with the volumetric flow-rate) and viscosity-induced resistance to flow. However, the interior of a flow, being better insulated, may react differently or record a later set of emplacement conditions. Clefts of toothpaste lava occurring within fields of clinker on proximal-type 'a'ā flows also record different shear rates during different times of flow emplacement. The interplay between viscosity and shear rate determines the final morphological lava type, and although no specific portion of lava ever makes a transition from 'a'ā back to pāhoehoe, parts of a flow can appear to do so.

Low latency counter event indication

DOEpatents

Gara, Alan G [Mount Kisco, NY; Salapura, Valentina [Chappaqua, NY

2008-09-16

A hybrid counter array device for counting events with interrupt indication includes a first counter portion comprising N counter devices, each for counting signals representing event occurrences and providing a first count value representing lower order bits. An overflow bit device associated with each respective counter device is additionally set in response to an overflow condition. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits. An operatively coupled control device monitors each associated overflow bit device and initiates incrementing a second count value stored at a corresponding memory location in response to a respective overflow bit being set. The incremented second count value is compared to an interrupt threshold value stored in a threshold register, and, when the second counter value is equal to the interrupt threshold value, a corresponding "interrupt arm" bit is set to enable a fast interrupt indication. On a subsequent roll-over of the lower bits of that counter, the interrupt will be fired.

Low latency counter event indication

DOEpatents

Gara, Alan G.; Salapura, Valentina

2010-08-24

A hybrid counter array device for counting events with interrupt indication includes a first counter portion comprising N counter devices, each for counting signals representing event occurrences and providing a first count value representing lower order bits. An overflow bit device associated with each respective counter device is additionally set in response to an overflow condition. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits. An operatively coupled control device monitors each associated overflow bit device and initiates incrementing a second count value stored at a corresponding memory location in response to a respective overflow bit being set. The incremented second count value is compared to an interrupt threshold value stored in a threshold register, and, when the second counter value is equal to the interrupt threshold value, a corresponding "interrupt arm" bit is set to enable a fast interrupt indication. On a subsequent roll-over of the lower bits of that counter, the interrupt will be fired.

A simulation of rainfall infiltration based on two-phase flow

NASA Astrophysics Data System (ADS)

Wang, Jun; Xi, Niannian; Liu, Gang; Hao, Shuang

2016-04-01

Rainfall infiltration in slope usually is one of major reasons cause landslide, which involves multiphase flow coupling with soil, water and gas. In order to study the mechanism of landslide caused by rainfall infiltration, a simulation of rainfall infiltration of DaPing slope, which locates in the Three Gorges Region of China, is presented based on the numerical solution of governing equations of two-phase flow in this paper. The results of this research suggest that there are two sections can be divided in the surface of slope, one is inflow area and the other is overflow area, according to where it is infiltration and discharge. The general inflow area is on the upside of slope, while the overflow area is on the underside. The middle section of slope is on a fluctuant position between inflow and overflow area, which is dramatically affected by the water content inside of slope. Moreover, the average rate of infiltration is more stable in both inflow and overflow area, whose numerical value is depend on the geometry and transmission characteristics of slope. And the factors of rainfall characteristics, surface flow and temperature have little effect on them. Furthermore, in the inflow area, when rainfall intensity is higher than infiltration the rain on the surface of slope will run off, otherwise water and gas will completely infiltrate through soil. The situation is different in the overflow area whose overland flow condition is depended on whether it is saturated or not inside of slope. When it is saturated in the slope, there is no infiltration in the overflow area. But when it is unsaturated, the infiltration intensity will equal to rainfall intensity. In a summary, the difference from inflow and overflow area is the evidence that the landslide may likely to happen on the slope of overflow area when it comes to a rainfall. It is disadvantageous for slope stability when transmitting the pressure of saturated water weight at the top of slope through the pore gas to groundwater, the groundwater pressure will increased sharply.

Combined sewer overflows to surface waters detected by the anthropogenic marker caffeine.

PubMed

Buerge, Ignaz J; Poiger, Thomas; Müller, Markus D; Buser, Hans-Rudolf

2006-07-01

Continuous progress in wastewater treatment technology and the growing number of households connected to wastewater treatment plants (WWTPs) have generally resulted in decreased environmental loading of many pollutants. Nonetheless, further reduction of pollutant inputs is required to improve the quality of surface waters in densely populated areas. In this context, the relative contribution of combined sewer overflows as sources of wastewater-derived contaminants has attracted more and more attention, but the quantitative importance of these overflows has barely been investigated. In this study, caffeine was successfully used as a chemical marker to estimate the fraction of sewer overflows in the catchment area of lake Greifensee, Switzerland. Caffeine is a ubiquitous compound in raw, domestic wastewater with typical per capita loads of approximately 16 mg person(-1) d(-1). In WWTPs of the Greifensee region, caffeine is largely eliminated (>99%), resulting in much smaller loads of < or = 0.15 mg person(-1) d(-1) in treated wastewater. However, in receiving streams as in the inflows to Greifensee, caffeine loads (0.1-1.6 mg person(-1) d(-1)) were higher than those in WWTP effluents, indicating additional sources. As the loads in the streams correlated with precipitation during sampling, it was concluded that combined sewer overflows were the most likely source of caffeine. Using a mass balance approach, it was possible to determine the fraction of wastewater (in dry weather equivalents) discharged untreated to the receiving streams (up to 10%, annual mean, approximately 2-3%). The concept of caffeine as a marker for combined sewer overflows was then applied to estimate phosphorus inputs to Greifensee with untreated and treated wastewater (approximately 1.5 and 2.0 t P y(-1), respectively), which corresponded well with P inputs determined in a separate study based on hydraulic considerations. For compounds with high elimination in WWTPs such as phosphorus (96-98% in the Greifensee area), inputs from combined sewer overflows are thus of similar magnitude as inputs from treated wastewater. The study demonstrated that caffeine is a suitable marker for untreated wastewater (from combined sewer overflows, direct discharges, etc.), but its sensitivity depends on regional conditions and decreases with decreasing elimination efficiency in WWTPs.

Optimise inlet condition and design parameters of a new sewer overflow screening device using numerical model.

PubMed

Aziz, M A; Imteaz, M A; Huda, Nazmul; Naser, J

2014-01-01

After heavy rainfall, sewer overflow spills to receiving water bodies cause serious concern for the environment, aesthetics and public health. To overcome these problems this study investigated a new self-cleansing sewer overflow screening device. The device has a sewer overflow chamber, a rectangular tank and a slotted ogee weir to capture the gross pollutants. To design an efficient screening device a numerical computational fluid dynamic (CFD) model was used. A plausibility check of the CFD model was done using a one-dimensional analytical model. Results showed that an inlet parallel to the weir ensured better self-cleansing than an inlet perpendicular to the weir. Perforations should be at the bottom of the weir to get increased velocity and shear stress to create a favourable self-cleaning effect of the screening device. Increasing inlet length from 0.3 to 1.5 m reduced wave reflection up to 10%, which increased flow uniformity downstream and improved self-cleansing effect. The orientation of the ogee weir with the rectangular tank was found most uniform with a 1:3 (horizontal:vertical) slope. These results will help to maximise functional efficiency of the new sewer overflow screening device. Otherwise it would be too expensive to alter after installation and at times difficult to customise accordingly to existing urban drainage systems.

Moving Stormwater Infrastructure from Real-time Control to Smart Systems

NASA Astrophysics Data System (ADS)

Wadzuk, B.; Bryant, S.; Lewellyn, C.; Zaremba, G.; Traver, R.

2017-12-01

Urban areas, especially combined sewer communities, are using green infrastructure (GI) systems (e.g. rain gardens, green roofs) to mitigate stormwater runoff volume, rate, and quality issues. Most municipal guidance and regulation limits these systems to static, passive designs that neither fully utilize the active hydrology of a GI system during and after a rainfall event, nor enable dynamic operational control. Real-time control (RTC) applied to GI is emerging, and under ideal model conditions has shown improved performance (i.e., greater volumes managed while minimizing downstream impact). There are a few RTC pilot field projects with promising results, such as on a cistern - green roof system there were only 30 overflow events out of 126 rain events and at a rain garden - cistern system only 1 of 81 events resulted in overflow. However, RTC does not get to a fully dynamic system as the initiation and consequent action is preset and static. In stormwater RTC systems, the initiation is typically a rain forecast or a sensor reading. At a rain garden - cistern system, a cistern that fills when raining is hard set to pump water to the rain garden 24 hours after the predicted rain ends. There have been instances where there is rain occurring or only a minimal amount of dry time for the rain garden to reestablish capacity for the pumped stored water. There is also no mechanism to automatically change the pump initiation time based on season or ambient conditions. A cistern - green roof system that uses stored water in an upstream cistern for green roof irrigation is initiated on a set soil moisture reading or a set irrigation volume daily. The soil moisture reading was rarely reached, so irrigation was often not initiated and the set daily irrigation volume did not vary over season. Moving from RTC to a smart system uses longer term and/or historical data to inform decisions beyond what a short-term forecast or real-time sensor can provide to give more context and flexibility in the initiation - consequent action logic. The use of the Standardized Precipitation Evapotranspiration Index as a back-cast and forecast tool to calculate an appropriate irrigation volume based on what rainfall is pending and whether the system is in drought state is used and discussed to move the GI systems into smart control.

Detention storage volume for combined sewer overflow into a river.

PubMed

Temprano, J; Tejero, I

2002-06-01

This article discusses the storage volume needed in a combined sewer system tank in order to preserve the water quality. There are a lot of design criteria which do not take into account the conditions of the receiving water, and as a result are inappropriate. A model was used to simulate the performance of a theoretical combined sewer system where a tank was located downstream. Results were obtained from the overflows produced by the rain recorded in Santander (Spain) for 11 years, with several combinations of storage volume and treatment capacity in the wastewater treatment plant. Quality criteria were also proposed for faecal coliforms, BOD, and total nitrogen to evaluate the effects from the overflows in the river water quality. Equations have been obtained which relate the number of overflows, the storage volume and the treatment plant capacity. The bacteriological pollution, quantified by means of faecal coliforms, was the analytical parameter which produced the most adverse effects in the river, so that more storage volume is needed (45 to 180 m3 ha(-1) net) than with other simulated pollutants (5 to 50 m3 ha(-1) net for BOD, and less than 4 m3 ha(-1) net for the total nitrogen). The increase in the treatment plant's capacity, from two to three times the flow in dry weather, reduces the impact on the river water in a more effective way, allowing a reduction of up to 65% in the number of overflows rather than increasing the storage volume.

Nuclear reactor overflow line

DOEpatents

Severson, Wayne J.

1976-01-01

The overflow line for the reactor vessel of a liquid-metal-cooled nuclear reactor includes means for establishing and maintaining a continuous bleed flow of coolant amounting to 5 to 10% of the total coolant flow through the overflow line to prevent thermal shock to the overflow line when the reactor is restarted following a trip. Preferably a tube is disposed concentrically just inside the overflow line extending from a point just inside the reactor vessel to an overflow tank and a suction line is provided opening into the body of liquid metal in the reactor vessel and into the annulus between the overflow line and the inner tube.

Quantifying excessive mirror overflow in children with attention-deficit/hyperactivity disorder

PubMed Central

MacNeil, L.K.; Xavier, P.; Garvey, M.A.; Gilbert, D.L.; Ranta, M.E.; Denckla, M.B.

2011-01-01

Objectives: Qualitative observations have revealed that children with attention-deficit/hyperactivity disorder (ADHD) show increased overflow movements, a motor sign thought to reflect impaired inhibitory control. The goal of this study was to develop and implement methods for quantifying excessive mirror overflow movements in children with ADHD. Methods: Fifty right-handed children aged 8.2–13.3 years, 25 with ADHD (12 girls) and 25 typically developing (TD) control children (10 girls), performed a sequential finger-tapping task, completing both left-handed (LHFS) and right-handed finger sequencing (RHFS). Phasic overflow of the index and ring fingers was assessed in 34 children with video recording, and total overflow in 48 children was measured by calculating the total angular displacement of the index and ring fingers with electrogoniometer recordings. Results: Phasic overflow and total overflow across both hands were greater in children with ADHD than in TD children, particularly during LHFS. Separate gender analyses revealed that boys, but not girls, with ADHD showed significantly more total phasic overflow and total overflow than did their gender-matched control children. Conclusions: The quantitative overflow measures used in this study support past qualitative findings that motor overflow persists to a greater degree in children with ADHD than in age-matched TD peers. The quantitative findings further suggest that persistence of mirror overflow is more prominent during task execution of the nondominant hand and reveal gender-based differences in developmental neural systems critical to motor control. These quantitative measures will assist future physiologic investigation of the brain basis of motor control in ADHD. PMID:21321336

A Study on the Fundamental Mechanism and the Evolutionary Driving Forces behind Aerobic Fermentation in Yeast

PubMed Central

Hagman, Arne; Piškur, Jure

2015-01-01

Baker’s yeast Saccharomyces cerevisiae rapidly converts sugars to ethanol and carbon dioxide at both anaerobic and aerobic conditions. The later phenomenon is called Crabtree effect and has been described in two forms, long-term and short-term effect. We have previously studied under fully controlled aerobic conditions forty yeast species for their central carbon metabolism and the presence of long-term Crabtree effect. We have also studied ten steady-state yeast cultures, pulsed them with glucose, and followed the central carbon metabolism and the appearance of ethanol at dynamic conditions. In this paper we analyzed those wet laboratory data to elucidate possible mechanisms that determine the fate of glucose in different yeast species that cover approximately 250 million years of evolutionary history. We determine overflow metabolism to be the fundamental mechanism behind both long- and short-term Crabtree effect, which originated approximately 125–150 million years ago in the Saccharomyces lineage. The “invention” of overflow metabolism was the first step in the evolution of aerobic fermentation in yeast. It provides a general strategy to increase energy production rates, which we show is positively correlated to growth. The “invention” of overflow has also simultaneously enabled rapid glucose consumption in yeast, which is a trait that could have been selected for, to “starve” competitors in nature. We also show that glucose repression of respiration is confined mainly among S. cerevisiae and closely related species that diverged after the whole genome duplication event, less than 100 million years ago. Thus, glucose repression of respiration was apparently “invented” as a second step to further increase overflow and ethanol production, to inhibit growth of other microbes. The driving force behind the initial evolutionary steps was most likely competition with other microbes to faster consume and convert sugar into biomass, in niches that were semi-anaerobic. PMID:25617754

A study on the fundamental mechanism and the evolutionary driving forces behind aerobic fermentation in yeast.

PubMed

Hagman, Arne; Piškur, Jure

2015-01-01

Baker's yeast Saccharomyces cerevisiae rapidly converts sugars to ethanol and carbon dioxide at both anaerobic and aerobic conditions. The later phenomenon is called Crabtree effect and has been described in two forms, long-term and short-term effect. We have previously studied under fully controlled aerobic conditions forty yeast species for their central carbon metabolism and the presence of long-term Crabtree effect. We have also studied ten steady-state yeast cultures, pulsed them with glucose, and followed the central carbon metabolism and the appearance of ethanol at dynamic conditions. In this paper we analyzed those wet laboratory data to elucidate possible mechanisms that determine the fate of glucose in different yeast species that cover approximately 250 million years of evolutionary history. We determine overflow metabolism to be the fundamental mechanism behind both long- and short-term Crabtree effect, which originated approximately 125-150 million years ago in the Saccharomyces lineage. The "invention" of overflow metabolism was the first step in the evolution of aerobic fermentation in yeast. It provides a general strategy to increase energy production rates, which we show is positively correlated to growth. The "invention" of overflow has also simultaneously enabled rapid glucose consumption in yeast, which is a trait that could have been selected for, to "starve" competitors in nature. We also show that glucose repression of respiration is confined mainly among S. cerevisiae and closely related species that diverged after the whole genome duplication event, less than 100 million years ago. Thus, glucose repression of respiration was apparently "invented" as a second step to further increase overflow and ethanol production, to inhibit growth of other microbes. The driving force behind the initial evolutionary steps was most likely competition with other microbes to faster consume and convert sugar into biomass, in niches that were semi-anaerobic.

46 CFR 153.408 - Tank overflow control.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Tank overflow control. 153.408 Section 153.408 Shipping... Systems § 153.408 Tank overflow control. (a) When table 1 references this section, a cargo containment... the tank (automatic shutdown system). (b) The high level alarm and the cargo overflow alarm or...

76 FR 13572 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

.... Specifically, it addresses the following flooding sources: Left Bank Overflow Main Stem Skagit River, Left Bank Overflow Main Stem Skagit River/South Fork Skagit River, Left Bank Overflow North Fork Skagit River, Main Stem Skagit River, North Fork Skagit River, Overflow from the Main Stem Skagit River between the North...

--No Title--

Science.gov Websites

;height:auto;overflow:hidden}.poc_table .top_row{background-color:#eee;height:auto;overflow:hidden}.poc_table ;background-color:#FFF;height:auto;overflow:hidden;border-top:1px solid #ccc}.poc_table .main_row .name :200px;padding:5px;height:auto;overflow:hidden}.tli_grey_box{background-color:#eaeaea;text-align:center

On the Other Hand: Overflow Movements of Infants’ Hands and Legs During Unimanual Object Exploration

PubMed Central

Soska, Kasey C.; Galeon, Margaret A.; Adolph, Karen E.

2011-01-01

Motor overflow is extraneous movement in a limb not involved in a motor action. Typically, overflow is observed in people with neurological impairments and in healthy children and adults during strenuous and attention-demanding tasks. In the current study, we found that young infants produce vast amounts of motor overflow, corroborating claims of symmetry being the default state of the motor system. While manipulating an object with one hand, all 27 of the typically-developing 4.5- to 7.5-month-old infants who we observed displayed overflow movements of the free hand (on 4/5 of unimanual actions). Mirror-image movements of the hands occurred on 1/8 of unimanual actions, and the hands and legs moved in synchrony on 1/3 of unimanual acts. Motor overflow was less frequent when infants were in a sitting posture and when infants watched their acting hand, suggesting that upright posture and visual examination may help to alleviate overflow and break obligatory symmetry in healthy infants. PMID:22487940

Modeling the effect of bus stops on capacity of curb lane

NASA Astrophysics Data System (ADS)

Luo, Qingyu; Zheng, Tianyao; Wu, Wenjing; Jia, Hongfei; Li, Jin

With the increase of buses and bus lines, a negative effect on road section capacity is made by the prolonged delay and queuing time at bus stops. However, existing methods of measuring the negative effect pay little attention to different bus stop types in the curb lanes. This paper uses Gap theory and Queuing theory to build models for effect-time and potential capacity in different conditions, including curbside bus stops, bus bays with overflow and bus bays without overflow. In order to make the effect-time models accurate and reliable, two types of probabilities are introduced. One is the probability that the dwell time is less than the headway of curb lane at curbside bus stops; the other is the overflow probability at bus bays. Based on the fundamental road capacity model and effect-time models, potential capacity models of curb lane are designed. The new models are calibrated by the survey data from Changchun City, and verified by the simulation software of VISSIM. Furthermore, with different arrival rates of vehicles, the setting conditions of bus stops are researched. Results show that the potential capacity models have high precision. They can offer a reference for recognizing the effect of bus stops on the capacity of curb lane, which can provide a basis for planning, design and management of urban roads and bus stops.

Flow dependence of forearm noradrenaline overflow, as assessed during mental stress and sodium nitroprusside infusion.

PubMed

Lindqvist, M; Melcher, A; Hjemdahl, P

1999-01-01

To evaluate the influence of blood flow on measurements of regional sympathetic nerve activity by radiotracer methodology ([3H]noradrenaline). Ten healthy men were studied under two conditions of elevated forearm blood flow: mental stress (Stroop colour word conflict test) and an intra-arterial infusion of sodium nitroprusside. Arterial blood pressure was measured invasively and forearm blood flow with strain-gauge plethysmography. Arterial and venous plasma adrenaline and noradrenaline were measured with high-performance liquid chromatography, and regional and total noradrenaline spillover were calculated. During mental stress, mean arterial pressure increased by 17%, heart rate by 16 beats/min, forearm blood flow by 117%, while forearm vascular resistance decreased by 44% (P < 0.001 for all). Sodium nitroprusside increased forearm blood flow dose-dependently, but elicited only minor effects on systemic haemodynamics. Mental stress increased arterial plasma noradrenaline by 52% (P < 0.001), and total body noradrenaline spillover by 75% (P < 0.001). During sodium nitroprusside infusion, arterial plasma noradrenaline increased only slightly and total body noradrenaline spillover was unaffected Forearm noradrenaline overflow increased from 5.4 +/- 0.9 to 16.9 +/- 2.6 pmol/min per I (P < 0.001) during mental stress and from 6.6 +/- 0.8 to 16.9 +/- 3.7 pmol/min per I (P < 0.001) during the second dose-step of sodium nitroprusside infusion. By intra-individual comparisons of forearm noradrenaline overflow increases during mental stress and during sodium nitroprusside infusion, with similar forearm blood flow increases, the flow dependence of forearm noradrenaline overflow was estimated. During mental stress, about 60% (median value, range 29-112%) of the increase in forearm noradrenaline overflow was attributed to the increase in forearm blood flow, whereas 40% was considered to reflect increased sympathetic nerve activity. There seems to be a considerable flow dependence of the regional overflow of noradrenaline, that is, a component of simple wash-out of noradrenaline from the forearm tissues during vasodilation. However, the present results still indicate that sympathetic nerve activity in the forearm is increased during mental stress, justifying the radiotracer technique for semiquantitative measurements, also during vasodilation.

Navier-Stokes and Comprehensive Analysis Performance Predictions of the NREL Phase VI Experiment

NASA Technical Reports Server (NTRS)

Duque, Earl P. N.; Burklund, Michael D.; Johnson, Wayne

2003-01-01

A vortex lattice code, CAMRAD II, and a Reynolds-Averaged Navier-Stoke code, OVERFLOW-D2, were used to predict the aerodynamic performance of a two-bladed horizontal axis wind turbine. All computations were compared with experimental data that was collected at the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Computations were performed for both axial as well as yawed operating conditions. Various stall delay models and dynamics stall models were used by the CAMRAD II code. Comparisons between the experimental data and computed aerodynamic loads show that the OVERFLOW-D2 code can accurately predict the power and spanwise loading of a wind turbine rotor.

A neuromorphic model of motor overflow in focal hand dystonia due to correlated sensory input

NASA Astrophysics Data System (ADS)

Sohn, Won Joon; Niu, Chuanxin M.; Sanger, Terence D.

2016-10-01

Objective. Motor overflow is a common and frustrating symptom of dystonia, manifested as unintentional muscle contraction that occurs during an intended voluntary movement. Although it is suspected that motor overflow is due to cortical disorganization in some types of dystonia (e.g. focal hand dystonia), it remains elusive which mechanisms could initiate and, more importantly, perpetuate motor overflow. We hypothesize that distinct motor elements have low risk of motor overflow if their sensory inputs remain statistically independent. But when provided with correlated sensory inputs, pre-existing crosstalk among sensory projections will grow under spike-timing-dependent-plasticity (STDP) and eventually produce irreversible motor overflow. Approach. We emulated a simplified neuromuscular system comprising two anatomically distinct digital muscles innervated by two layers of spiking neurons with STDP. The synaptic connections between layers included crosstalk connections. The input neurons received either independent or correlated sensory drive during 4 days of continuous excitation. The emulation is critically enabled and accelerated by our neuromorphic hardware created in previous work. Main results. When driven by correlated sensory inputs, the crosstalk synapses gained weight and produced prominent motor overflow; the growth of crosstalk synapses resulted in enlarged sensory representation reflecting cortical reorganization. The overflow failed to recede when the inputs resumed their original uncorrelated statistics. In the control group, no motor overflow was observed. Significance. Although our model is a highly simplified and limited representation of the human sensorimotor system, it allows us to explain how correlated sensory input to anatomically distinct muscles is by itself sufficient to cause persistent and irreversible motor overflow. Further studies are needed to locate the source of correlation in sensory input.

A Bayesian network model to assess the public health risk associated with wet weather sewer overflows discharging into waterways.

PubMed

Goulding, R; Jayasuriya, N; Horan, E

2012-10-15

Overflows from sanitary sewers during wet weather, which occur when the hydraulic capacity of the sewer system is exceeded, are considered a potential threat to the ecological and public health of the waterways which receive these overflows. As a result, water retailers in Australia and internationally commit significant resources to manage and abate sewer overflows. However, whilst some studies have contributed to an increased understanding of the impacts and risks associated with these events, they are relatively few in number and there still is a general lack of knowledge in this area. A Bayesian network model to assess the public health risk associated with wet weather sewer overflows is presented in this paper. The Bayesian network approach is shown to provide significant benefits in the assessment of public health risks associated with wet weather sewer overflows. In particular, the ability for the model to account for the uncertainty inherent in sewer overflow events and subsequent impacts through the use of probabilities is a valuable function. In addition, the paper highlights the benefits of the probabilistic inference function of the Bayesian network in prioritising management options to minimise public health risks associated with sewer overflows. Copyright © 2012. Published by Elsevier Ltd.

Modeling climate change impacts on combined sewer overflow using synthetic precipitation time series.

PubMed

Bendel, David; Beck, Ferdinand; Dittmer, Ulrich

2013-01-01

In the presented study climate change impacts on combined sewer overflows (CSOs) in Baden-Wuerttemberg, Southern Germany, were assessed based on continuous long-term rainfall-runoff simulations. As input data, synthetic rainfall time series were used. The applied precipitation generator NiedSim-Klima accounts for climate change effects on precipitation patterns. Time series for the past (1961-1990) and future (2041-2050) were generated for various locations. Comparing the simulated CSO activity of both periods we observe significantly higher overflow frequencies for the future. Changes in overflow volume and overflow duration depend on the type of overflow structure. Both values will increase at simple CSO structures that merely divide the flow, whereas they will decrease when the CSO structure is combined with a storage tank. However, there is a wide variation between the results of different precipitation time series (representative for different locations).

Characteristics of the overflow pollution of storm drains with inappropriate sewage entry.

PubMed

Yin, Hailong; Lu, Yi; Xu, Zuxin; Li, Huaizheng; Schwegler, Benedict R

2017-02-01

To probe the overflow pollution of separate storm drains with inappropriate sewage entries, in terms of the relationship between sewage entries and the corresponding dry-weather and wet-weather overflow, the monitoring activities were conducted in a storm drainage system in the Shanghai downtown area (374 ha). In this study site, samples from inappropriately entered dry-weather sewage and the overflow due to storm pumps operation on dry-weather and wet-weather days were collected and then monitored for six water quality constituents. It was found that overflow concentrations of dry-weather period could be higher than those of wet-weather period; under wet-weather period, the overflow concentrations of storm drains were close to or even higher than that of combined sewers. Relatively strong first flush mostly occurred under heavy rain that satisfied critical rainfall amount, maximum rainfall intensity, and maximum pumping discharge, while almost no first flush effect or only weak first flush effect was found for the other rainfall events. Such phenomenon was attributed to lower in-line pipe storage as compared to that of the combined sewers, and serious sediment accumulation within the storm pipes due to sewage entry. For this kind of system, treating a continuous overflow rate is a better strategy than treating the maximum amount of early part of the overflow. Correcting the key inappropriate sewage entries into storm drains should also be focused.

Tidal reversal and flow velocities using temperature and specific conductance in a small wetland creek

NASA Astrophysics Data System (ADS)

Eaton, Timothy T.

2016-11-01

Characterizing flow dynamics in very small tidal creeks is complicated and not well suited to methods developed for upland streams or coastal estuaries, due to low flows, bidirectionality and shallow waters. Simple instrumentation enables thermal and salinity signals to be used to observe flow directions and estimate velocities in these settings. Using multiple inexpensive sensors over 500 m along a tidally influenced wetland creek, I demonstrate how advection of temperature and specific conductance pulses reveal flood and ebb tides and the temporary reversal of flow by warmer, estuarine water from the receiving embayment. The sequential rise of temperature upstream was most evident under hot and dry conditions, after daily peak air temperatures of 25 °C or above, and was subdued or disrupted under cooler or rainy conditions in summertime. Changes in specific conductance at successive sites upstream were less susceptible to environmental influences and confirm tidal flood velocity of between 0.07 and 0.37 m/s. The tidally-induced flow reversal suggests that periodic high tide conditions can interfere with rapid dispersal of pollution discharges, such as from the combined sewer overflow (CSO) located upstream of the studied creek reach. This low-cost approach of temperature and specific conductance sensing in vegetated coastal wetlands where access, precise elevation control and creek discharge measurements are difficult, provides a simple way of tracking water masses when sufficient contrast exists between water sources.

MANAGEMENT AND CONTROL OF COMBINED SEWER OVERFLOWS

EPA Science Inventory

The paper gives a basic overview of the U.S. government's involvements in developing countermeasures for the abatement of combined sewer overflow pollution. batement or prevention of pollution stormwater runoff and combined sewer overflows is one of the most challenging areas in ...

FLOCCULATION-FLOTATION AIDS FOR TREATMENT OF COMBINED SEWER OVERFLOWS

EPA Science Inventory

The objectives of this study were to investigate the flocculation/flotation characteristics of combined sewer overflow through laboratory and field testing. The concept involves the introduction of chemicals and buoyant flotation aids into the overflow and the subsequent cofloccu...

COMBINED-SEWER OVERFLOW CONTROL AND TREATMENT

EPA Science Inventory

Combined-sewer overflow (CSO), along with sanitary-sewer overflow and stormwater are significant contributors of contamination to surface waters. During a rain event, the flow in a combined sewer system may exceed the capacity of the intercepting sewer leading to the wastewater t...

Validation of OVERFLOW for Supersonic Retropropulsion

NASA Technical Reports Server (NTRS)

Schauerhamer, Guy

2012-01-01

The goal is to softly land high mass vehicles (10s of metric tons) on Mars. Supersonic Retropropulsion (SRP) is a potential method of deceleration. Current method of supersonic parachutes does not scale past 1 metric ton. CFD is of increasing importance since flight and experimental data at these conditions is difficult to obtain. CFD must first be validated at these conditions.

Characteristics of the Nordic Seas overflows in a set of Norwegian Earth System Model experiments

NASA Astrophysics Data System (ADS)

Guo, Chuncheng; Ilicak, Mehmet; Bentsen, Mats; Fer, Ilker

2016-08-01

Global ocean models with an isopycnic vertical coordinate are advantageous in representing overflows, as they do not suffer from topography-induced spurious numerical mixing commonly seen in geopotential coordinate models. In this paper, we present a quantitative diagnosis of the Nordic Seas overflows in four configurations of the Norwegian Earth System Model (NorESM) family that features an isopycnic ocean model. For intercomparison, two coupled ocean-sea ice and two fully coupled (atmosphere-land-ocean-sea ice) experiments are considered. Each pair consists of a (non-eddying) 1° and a (eddy-permitting) 1/4° horizontal resolution ocean model. In all experiments, overflow waters remain dense and descend to the deep basins, entraining ambient water en route. Results from the 1/4° pair show similar behavior in the overflows, whereas the 1° pair show distinct differences, including temperature/salinity properties, volume transport (Q), and large scale features such as the strength of the Atlantic Meridional Overturning Circulation (AMOC). The volume transport of the overflows and degree of entrainment are underestimated in the 1° experiments, whereas in the 1/4° experiments, there is a two-fold downstream increase in Q, which matches observations well. In contrast to the 1/4° experiments, the coarse 1° experiments do not capture the inclined isopycnals of the overflows or the western boundary current off the Flemish Cap. In all experiments, the pathway of the Iceland-Scotland Overflow Water is misrepresented: a major fraction of the overflow proceeds southward into the West European Basin, instead of turning westward into the Irminger Sea. This discrepancy is attributed to excessive production of Labrador Sea Water in the model. The mean state and variability of the Nordic Seas overflows have significant consequences on the response of the AMOC, hence their correct representations are of vital importance in global ocean and climate modelling.

Measuring Flow Reductions in a Combined Sewer System using Green Infrastructure - abstract

EPA Science Inventory

In 2009, the Louisville and Jefferson County Metropolitan Sewer District (MSD) submitted an Integrated Overflow Abatement Plan (IOAP) addressing combined sewer overflows (CSOs) and sanitary sewer overflows. Many of the solutions involve gray infrastructure, such as large, end-of...

Development of Software Sensors for Determining Total Phosphorus and Total Nitrogen in Waters

PubMed Central

Lee, Eunhyoung; Han, Sanghoon; Kim, Hyunook

2013-01-01

Total nitrogen (TN) and total phosphorus (TP) concentrations are important parameters to assess the quality of water bodies and are used as criteria to regulate the water quality of the effluent from a wastewater treatment plant (WWTP) in Korea. Therefore, continuous monitoring of TN and TP using in situ instruments is conducted nationwide in Korea. However, most in situ instruments in the market are expensive and require a time-consuming sample pretreatment step, which hinders the widespread use of in situ TN and TP monitoring. In this study, therefore, software sensors based on multiple-regression with a few easily in situ measurable water quality parameters were applied to estimate the TN and TP concentrations in a stream, a lake, combined sewer overflows (CSOs), and WWTP effluent. In general, the developed software sensors predicted TN and TP concentrations of the WWTP effluent and CSOs reasonably well. However, they showed relatively lower predictability for TN and TP concentrations of stream and lake waters, possibly because the water quality of stream and lake waters is more variable than that of WWTP effluent or CSOs. PMID:23307350

Investigation of vinegar production using a novel shaken repeated batch culture system.

PubMed

Schlepütz, Tino; Büchs, Jochen

2013-01-01

Nowadays, bioprocesses are developed or optimized on small scale. Also, vinegar industry is motivated to reinvestigate the established repeated batch fermentation process. As yet, there is no small-scale culture system for optimizing fermentation conditions for repeated batch bioprocesses. Thus, the aim of this study is to propose a new shaken culture system for parallel repeated batch vinegar fermentation. A new operation mode - the flushing repeated batch - was developed. Parallel repeated batch vinegar production could be established in shaken overflow vessels in a completely automated operation with only one pump per vessel. This flushing repeated batch was first theoretically investigated and then empirically tested. The ethanol concentration was online monitored during repeated batch fermentation by semiconductor gas sensors. It was shown that the switch from one ethanol substrate quality to different ethanol substrate qualities resulted in prolonged lag phases and durations of the first batches. In the subsequent batches the length of the fermentations decreased considerably. This decrease in the respective lag phases indicates an adaptation of the acetic acid bacteria mixed culture to the specific ethanol substrate quality. Consequently, flushing repeated batch fermentations on small scale are valuable for screening fermentation conditions and, thereby, improving industrial-scale bioprocesses such as vinegar production in terms of process robustness, stability, and productivity. Copyright © 2013 American Institute of Chemical Engineers.

Focused Field Investigations for Sewer Condition Assessment with EPA SSOAP Toolbox

EPA Science Inventory

The Nation’s sanitary sewer infrastructure is aging, and is currently one of the top national water program priorities. The U.S. Environmental Protection Agency (EPA) developed the Sanitary Sewer Overflow Analysis and Planning (SSOAP) Toolbox to assist communities in developing ...

A model to simulate the haemodynamic effects of right heart pulsatile flow after modified Fontan procedure.

PubMed

Tamaki, S; Kawazoe, K; Yagihara, T; Abe, T

1992-02-01

The effect of pulsatile pulmonary flow after the modified Fontan procedure was examined in a model that simulated the right heart. An inlet overflow tank (preload), axial pulsatile pump, Wind-Kessel model (afterload), and an outlet overflow tank were connected in series. The standard conditions were flow 2.00 l/min with 12 mm Hg preload pressure, 3.0 Wood units resistance, and an outlet overflow tank pressure at 6 mm Hg. The pump rate was set at 80 beats/min. The simulated pulmonary arterial pressure and pulmonary flow waves produced by this model closely resembled those obtained from patients who had undergone the modified Fontan procedure. All variables except the preload were fixed and changes in pulmonary flow were examined at preload pressures of 8, 12, 15, and 17 mm Hg. As the peak pulmonary arterial pressure increased so did pulmonary flow, until it was greater than during the non-pulsatile state. Because the afterload of this model was fixed, this result suggests that there was a concomitant decrease in resistance. This model indicates that pulsatile pulmonary blood flow is likely to have a beneficial effect on the pulmonary circulation after the modified Fontan procedure.

Comparison of conventional rule based flow control with control processes based on fuzzy logic in a combined sewer system.

PubMed

Klepiszewski, K; Schmitt, T G

2002-01-01

While conventional rule based, real time flow control of sewer systems is in common use, control systems based on fuzzy logic have been used only rarely, but successfully. The intention of this study is to compare a conventional rule based control of a combined sewer system with a fuzzy logic control by using hydrodynamic simulation. The objective of both control strategies is to reduce the combined sewer overflow volume by an optimization of the utilized storage capacities of four combined sewer overflow tanks. The control systems affect the outflow of four combined sewer overflow tanks depending on the water levels inside the structures. Both systems use an identical rule base. The developed control systems are tested and optimized for a single storm event which affects heterogeneously hydraulic load conditions and local discharge. Finally the efficiencies of the two different control systems are compared for two more storm events. The results indicate that the conventional rule based control and the fuzzy control similarly reach the objective of the control strategy. In spite of the higher expense to design the fuzzy control system its use provides no advantages in this case.

Long-term observing system for the oceanic regime of Filchner-Ronne Ice Shelf, Antarctica

NASA Astrophysics Data System (ADS)

Østerhus, Svein; Schröder, Michael; Hellmer, Hartmunt; Darelius, Elin; Nicholls, Keith; Makinson, Keith

2014-05-01

Long term observations of the flow of dense waters from their area of formation to the abyss of the World Ocean, and the return flow of warm waters, are central to climate research. For the Weddell Sea an important component of such a system entails monitoring the formation of High Salinity Shelf Water (HSSW) on the continental shelf north of Ronne Ice Front, the transformation to Ice Shelf Water (ISW) beneath the floating Filchner-Ronne ice shelf, and the flux of ISW overflowing the shelf break to the deep Weddell Sea. Equally important is the return flow of warm water toward the Filchner-Ronne Ice Shelf system. AWI, BAS and UNI/UIB operate a number of monitoring stations in the southern Weddell Sea. The systems build upon techniques and methods developed over several decades and have a proven record of high data return. Here we present plans for extending, integrating and operating the existing long term observatories to increase our knowledge of the natural variability of the ocean-ice shelf system, and to allow early identification of possible changes of regional or global importance. The S2 observatory at the Filchner sill was established in 1977 and continues to deliver the longest existing marine time series from Antarctica. As a key site for monitoring the ISW overflow S2 is a part of the global net of monitoring sites under CLIVAR Southern Ocean Observing System (SOOS) and OceanSITES. The existing S2 observatory consists of a sub-surface mooring carrying sensors for current velocity, temperature, salinity and dissolved oxygen measurements. Observations at the Filchner sill also show a seasonal inflow of relatively warm water that is able to reach Filchner Ice Front. New model results indicate that this flow of water might increase in the future and we have deployed a number of instrumented moorings in the Filchner Depression to estimate the heat flux towards the ice shelf. In 1999 we established Site 5 on Ronne Ice Shelf using a hot-water drill to access the 402 m of water underlying the 763-m thick ice. Results from the multiyear time series show the sensitivity of the sub-ice shelf circulation to changes in conditions over the continental shelf and highlight the importance of monitoring the ice shelf cavity. We will reoccupy Site 5 in the 2014/15 season to deploy a suite of observing systems for long time monitoring of the circulation below Ronne Ice Shelf. The systems will consist of sub-ice shelf oceanographic moorings instrumented with high quality sensors. They will transmit in real-time and are designed to operate for more than 10 years. In 2015/16 we will extend the observing network by deploying observatories on Filchner Ice Shelf. The Filchner-Ronne Ice Shelf and S2 observatories will provide the first ever concurrent observations from the ice-shelf cavity where ISW is formed, and the sill where it starts its descent towards the deep Weddell Sea, and will provide a unique dataset allowing us to link processes and variability within the cavity directly to overflow properties and deep water formation.

COVERT: A Framework for Finding Buffer Overflows in C Programs via Software Verification

DTIC Science & Technology

2010-08-01

is greater than the allocated size of B. In the case of a type-safe language or a language with runtime bounds checking (such as Java), an overflow...leads either to a (compile-time) type error or a (runtime) exception. In such languages , a buffer overflow can lead to a denial of service attack (i.e...of current and legacy software is written in unsafe languages (such as C or C++) that allow buffers to be overflowed with impunity. For reasons such as

Overflow Simulations using MPAS-Ocean in Idealized and Realistic Domains

NASA Astrophysics Data System (ADS)

Reckinger, S.; Petersen, M. R.; Reckinger, S. J.

2016-02-01

MPAS-Ocean is used to simulate an idealized, density-driven overflow using the dynamics of overflow mixing and entrainment (DOME) setup. Numerical simulations are benchmarked against other models, including the MITgcm's z-coordinate model and HIM's isopycnal coordinate model. A full parameter study is presented that looks at how sensitive overflow simulations are to vertical grid type, resolution, and viscosity. Horizontal resolutions with 50 km grid cells are under-resolved and produce poor results, regardless of other parameter settings. Vertical grids ranging in thickness from 15 m to 120 m were tested. A horizontal resolution of 10 km and a vertical resolution of 60 m are sufficient to resolve the mesoscale dynamics of the DOME configuration, which mimics real-world overflow parameters. Mixing and final buoyancy are least sensitive to horizontal viscosity, but strongly sensitive to vertical viscosity. This suggests that vertical viscosity could be adjusted in overflow water formation regions to influence mixing and product water characteristics. Also, the study shows that sigma coordinates produce much less mixing than z-type coordinates, resulting in heavier plumes that go further down slope. Sigma coordinates are less sensitive to changes in resolution but as sensitive to vertical viscosity compared to z-coordinates. Additionally, preliminary measurements of overflow diagnostics on global simulations using a realistic oceanic domain are presented.

Fast Tracking Data to Informed Decisions: An Advanced Information System to Improve Environmental Understanding and Management (Invited)

NASA Astrophysics Data System (ADS)

Minsker, B. S.; Myers, J.; Liu, Y.; Bajcsy, P.

2010-12-01

Emerging sensing and information technology are rapidly creating a new paradigm for environmental research and management, in which data from multiple sensors and information sources can guide real-time adaptive observation and decision making. This talk will provide an overview of emerging cyberinfrastructure and three case studies that illustrate their potential: combined sewer overflows in Chicago, hypoxia in Corpus Christi Bay, Texas, and sustainable agriculture in Illinois. An advanced information system for real-time decision making and visual geospatial analytics will be presented as an example of cyberinfrastructure that enables easier implementation of numerous real-time applications.

Focused Field Investigations for Sewer Condition Assessment with EPA SSOAP Toolbox - slides

EPA Science Inventory

The Nation’s sanitary sewer infrastructure is aging, and is currently one of the top national water program priorities. The U.S. Environmental Protection Agency (EPA) developed the Sanitary Sewer Overflow Analysis and Planning (SSOAP) Toolbox to assist communities in developing S...

Muscarinic inhibition of [3H]-noradrenaline release on rabbit iris in vitro: effects of stimulation conditions on intrinsic activity of methacholine and pilocarpine.

PubMed Central

Bognar, I. T.; Pallas, S.; Fuder, H.; Muscholl, E.

1988-01-01

1. Rabbit isolated irides were loaded with [3H]-noradrenaline and superfused with Tyrode solution. The inhibition by the muscarinic agonists (+/-)-methacholine and pilocarpine of the [3H]-noradrenaline overflow into the superfusate evoked by field stimulation (pulses of 1 ms duration, 75 mA) was measured as an index of activation of presynaptic muscarinic receptors. 2. The fractional rate of release per pulse during the first stimulation period (S1) was low with 360 pulses at 3 Hz, intermediate with 360 pulses at 10 Hz and high with 1200 pulses at 10 Hz. Upon repetitive stimulation (7 periods at 20 min intervals), the fractional rates of release per pulse during S7 no longer differed, suggesting a 'long-term' regulation of [3H]-noradrenaline release depending on the stimulation conditions. 3. The evoked [3H]-noradrenaline overflow was depressed by (+/-)-methacholine in a concentration-dependent manner. The EC50 ranged from 0.29 to 0.42 microM. Methacholine nearly abolished the transmitter release evoked at 3 Hz but reduced that induced at 10 Hz by only 50%. Under the latter condition the methacholine concentration-inhibition curve was bell-shaped and no muscarinic inhibition was observed in the presence of methacholine 30 microM. After washout of methacholine the evoked [3H]-noradrenaline release was temporarily enhanced. 4. Atropine 0.1 microM enhanced the [3H]-noradrenaline overflow (evoked by stimulation with 360 or 1200 pulses at 10 Hz), probably antagonizing a presynaptic inhibition by endogenous acetylcholine. The inhibition by methacholine was competitively antagonized by atropine 0.1 microM (apparent -log KB = 8.5-9.0). 5. Depending on the concentration, pilocarpine reduced the [3H]-noradrenaline overflow evoked by 360 pulses at 3 Hz up to 63%. However, at 10 Hz stimulation frequency the compound was inactive as an agonist but competitively antagonized the presynaptic inhibition induced by methacholine. The KB under the latter condition (0.95 microM) was very close to the EC50 value determined at 3 Hz (0.85 microM). 6. The results demonstrate a muscarinic inhibition of noradrenaline release from the rabbit isolated iris. The activation by pilocarpine of the presynaptic receptors provides an alternative explanation for the miosis induced in the rabbit in vivo, which might be the result of a decreased sympathetic tone in the iris dilator muscle. PMID:3052680

High level radioactive waste vitrification process equipment component testing

NASA Astrophysics Data System (ADS)

Siemens, D. H.; Health, W. C.; Larson, D. E.; Craig, S. N.; Berger, D. N.; Goles, R. W.

1985-04-01

Remote operability and maintainability of vitrification equipment were assessment under shielded cell conditions. The equipment tested will be applied to immobilize high level and transuranic liquid waste slurries that resulted from plutonium production for defense weapons. Equipment tested included: a turntable for handling waste canisters under the melter; a removable discharge cone in the melter overflow section; a thermocouple jumper that extends into a shielded cell; remote instrument and electrical connectors; remote, mechanical, and heat transfer aspects of the melter glass overflow section; a reamer to clean out plugged nozzles in the melter top; a closed circuit camera to view the melter interior; and a device to retrieve samples of the glass product. A test was also conduucted to evaluate liquid metals for use in a liquid metal sealing system.

46 CFR 153.408 - Tank overflow control.

Code of Federal Regulations, 2010 CFR

2010-10-01

... automatic shutdown system must: (1) Be independent of one-another; and (2) Operate on loss of power. (c) The... lettering as specified for the warning sign in § 153.955. (e) A tank overflow alarm must be audible and... loading is controlled on the tankship. (f) The automatic shutdown system or tank overflow alarm must be...

46 CFR 153.408 - Tank overflow control.

Code of Federal Regulations, 2011 CFR

2011-10-01

... automatic shutdown system must: (1) Be independent of one-another; and (2) Operate on loss of power. (c) The... lettering as specified for the warning sign in § 153.955. (e) A tank overflow alarm must be audible and... loading is controlled on the tankship. (f) The automatic shutdown system or tank overflow alarm must be...

Cost Comparison of Conventional Gray Combined Sewer Overflow Control Infrastructure versus a Green/Gray Combination

EPA Science Inventory

This paper outlines a life-cycle cost analysis comparing a green (rain gardens) and gray (tunnels) infrastructure combination to a gray-only option to control combined sewer overflow in the Turkey Creek Combined Sewer Overflow Basin, in Kansas City, MO. The plan area of this Bas...

MICROORGANISM DIE-OFF RATES UNDER VARIOUS CONDITIONS

EPA Science Inventory

New York-New Jersey (NY-NJ) Harbor Estuary Program is charged to undertake an assessment of New York City Combined Sewer Overflow (NYC CSO) model for use in developing Total Maximum Daily Loads (TMDLs) which are scheduled for submission to EPA Region 2 by May 2006. A TMDL is def...

EPA SSOAP Toolbox Application for Condition and Capacity Assessment of Wastewater Collection Systems - Paper

EPA Science Inventory

The nation’s sanitary sewer infrastructure is aging, with some sewers dating back more than 100 years. Nationwide, there are more than 19,500 municipal sanitary-sewer collection systems serving an estimated 150 million people and about 40,000 sanitary sewer overflow (SSO) events ...

EPA SSOAP Toolbox Application for Condition and Capacity Assessment of Wastewater Collection Systems

EPA Science Inventory

The Nation’s sanitary sewer infrastructure is aging, with some sewers dating back over 100 years. Nationwide, there are more than 19,500 municipal sanitary-sewer collection systems serving an estimated 150 million people and about 40,000 sanitary sewer overflow (SSO) events per ...

STRUCTURAL CAPABILITIES OF NO-DIG MANHOLE REHABILITATION (WE&RF Report INFR1R12)

EPA Science Inventory

Failure of a manhole may have catastrophic consequences such as a sinkhole. At a minimum, wastewater flow will be blocked and flow upstream of the manhole will backup, causing a sanitary sewer overflow (SSO). Accordingly, the structural condition of a manhole is an important perf...

Advances in Sewer Condition and Capacity Assessment – Development and Applications of EPA SSOAP Toolbox

EPA Science Inventory

In the United States, sanitary sewer infrastructure is aging, with some sewers dating back over 100 years. Nationwide, there are more than 19,500 municipal sanitary-sewer collection systems serving an estimated 150 million people and about 40,000 sanitary sewer overflow (SSO) ev...

U.S. EPA Issues Technical Guides and Computer Tools for Sewer Condition and Capacity Assessment

EPA Science Inventory

The nation's sanitary sewer infrastructure is aging, with some sewers more than100 years old. Nationwide, there are more than 19,500 municipal sanitary-sewer collection systems serving an estimated 150 million people and about 40,000 sanitary sewer overflow (SSO) events per year...

Focused Field Investigations for Sewer Condition Assessment with EPA SSOAP Toolbox - abstract

EPA Science Inventory

The Nation’s sanitary sewer infrastructure is aging, and it is currently one of the top national water program priorities, and is one of the top priorities of the U.S. Conference of Mayors. The U.S. Environmental Protection Agency developed the Sanitary Sewer Overflow Analysis a...

Focused Field Investigations for Sewer Condition Assessment with EPA SSOAP Toolbox

EPA Science Inventory

The Nation’s sanitary sewer infrastructure is aging, and it is currently one of the top national water program priorities, and is one of the top priorities of the U.S. Conference of Mayors. The U.S. Environmental Protection Agency (EPA) developed the Sanitary Sewer Overflow Anal...

Finger muscle control in children with dystonia.

PubMed

Young, Scott J; van Doornik, Johan; Sanger, Terence D

2011-06-01

Childhood dystonia is a disorder that involves inappropriate muscle activation during attempts at voluntary movement. Few studies have investigated the muscle activity associated with dystonia in children, and none have done so in the hands. In this study, we measured surface electromyographic activity in four intrinsic hand muscles while participants attempted to perform an isometric tracking task using one of the muscles. Children with dystonia had greater tracking error with the task-related muscle and greater overflow to non-task muscles. Both tracking error and overflow correlated with the Barry-Albright Dystonia scale of the respective upper limb. Overflow also decreased when participants received visual feedback of non-task muscle activity. We conclude that two of the motor deficits in childhood dystonia--motor overflow and difficulties in actively controlling muscles--can be seen in the surface electromyographic activity of individual muscles during an isometric task. As expected from results in adults, overflow is an important feature of childhood dystonia. However, overflow may be at least partially dependent on an individual's level of awareness of their muscle activity. Most importantly, poor single-muscle tracking shows that children with dystonia have deficits of individual muscle control in addition to overflow or co-contraction. These results provide the first quantitative measures of the muscle activity associated with hand dystonia in children, and they suggest possible directions for control of dystonic symptoms. Copyright © 2011 Movement Disorder Society.

Finger Muscle Control in Children with Dystonia

PubMed Central

Young, Scott J.; van Doornik, Johan; Sanger, Terence D.

2010-01-01

Childhood dystonia is a disorder that involves inappropriate muscle activation during attempts at voluntary movement. Few studies have investigated the muscle activity associated with dystonia in children, and none have done so in the hands. In this study, we measured surface electromyographic activity in four intrinsic hand muscles while participants attempted to perform an isometric tracking task using one of the muscles. Children with dystonia had greater tracking error with the task-related muscle and greater overflow to non-task muscles. Both tracking error and overflow correlated with the Barry-Albright Dystonia scale of the respective upper limb. Overflow also decreased when participants received visual feedback of non-task muscle activity. We conclude that two of the motor deficits in childhood dystonia—motor overflow and difficulties in actively controlling muscles—can be seen in the surface electromyographic activity of individual muscles during an isometric task. As expected from results in adults, overflow is an important feature of childhood dystonia. However, overflow may be at least partially dependent on an individual’s level of awareness of their muscle activity. Most importantly, poor single-muscle tracking shows that children with dystonia have deficits of individual muscle control in addition to overflow or co-contraction. These results provide the first quantitative measures of the muscle activity associated with hand dystonia in children, and they suggest possible directions for control of dystonic symptoms. PMID:21449015

A Developmental Study of the Influence of Task Characteristics on Motor Overflow

ERIC Educational Resources Information Center

Addamo, Patricia K.; Farrow, Maree; Hoy, Kate E.; Bradshaw, John L.; Georgiou-Karistianis, Nellie

2009-01-01

Motor overflow refers to involuntary movement or muscle activity that may coincide with voluntary movement. This study examined factors influencing motor overflow in 17 children (8-11 years), and 17 adults (18-35 years). Participants performed a finger pressing task by exerting either 33% or 66% of their maximal force output using their dominant…

A maximum contraction and substantial quantities of tritium can be obtained from tetraethylammonium-treated [3H]-noradrenaline preloaded, rat vas deferens in response to a single electrical shock.

PubMed Central

Wakade, A. R.

1980-01-01

1 In the normal and phenoxybenzamine-treated vasa deferentia of the rat the overflow of tritium after preloading with [3H]-noradrenaline increased with the increase in frequency of transmural stimulation. Phenozybenzamine enhanced overflow by 5 to 7 fold. 2 After tetraethylammonium (TEA, 10 mM), fractional tritium overflow at 5 Hz increased from a control value of 2.8 to 53 X 10(-4), and at 0.5 Hz it reached 154 X 10(-4). Enhancement of overflow was inversely related to the frequency of stimulation. 3 Contractor responses of the vas deferens induced by transmural stimulation were markedly potentiated, both in amplitude and duration, by 10 mM TEA. The contraction developed in the presence of 10 mM TEA at 0.5 Hz was comparable to that obtained at 10 Hz in normal Krebs solution. 4 In the presence of 5 mM TEA, contractions of the vas deferens caused by exogenous noradrenaline were potentiated about 5 fold. 5 The overflow and contractor response induced by 45 mM K were enhanced about 5 fold in 10 mM TEA-Krebs solution. Facilitation of K-induced overflow by TEA was reduced over 50% by tetrodotoxin (TTX, 1 microM). 6 Delivery of a single shock (1.0 ms duration) to 10 mM TEA-treated vas deferens resulted in a 63% increase in tritium overflow over background overflow. The fractional overflow amounted to almost 720 X 10(-4) after a single shock, as compared to 154 X 10(-4) obtained at 0.5 Hz. 7 The vas deferens treated with 10 mM TEA and stimulated by a single shock developed a contraction which was greater in amplitude and duration than that seen in normal tissue at 10 Hz. 8 Five second serial samples collected from superfused 10 mM TEA-treated vas deferens contained maximum quantities of radioactivity in the first 5 s after a single shock. In subsequent samples, radioactivity gradually declined, and reached prestimulation level after about 25 s. 9 The fractional overflow caused by stimulation at 0.1 Hz in 10 mM TEA-treated tissue progressively increased as external Ca was gradually raised from 0.83 to 10 mM. 10 The mechanism of action of TEA in enhancing the overflow of sympathetic transmitter, particularly in response to a single shock, is discussed in relation to Ca. PMID:7052336

High-resolution marine flood modelling coupling overflow and overtopping processes: framing the hazard based on historical and statistical approaches

NASA Astrophysics Data System (ADS)

Nicolae Lerma, Alexandre; Bulteau, Thomas; Elineau, Sylvain; Paris, François; Durand, Paul; Anselme, Brice; Pedreros, Rodrigo

2018-01-01

A modelling chain was implemented in order to propose a realistic appraisal of the risk in coastal areas affected by overflowing as well as overtopping processes. Simulations are performed through a nested downscaling strategy from regional to local scale at high spatial resolution with explicit buildings, urban structures such as sea front walls and hydraulic structures liable to affect the propagation of water in urban areas. Validation of the model performance is based on hard and soft available data analysis and conversion of qualitative to quantitative information to reconstruct the area affected by flooding and the succession of events during two recent storms. Two joint probability approaches (joint exceedance contour and environmental contour) are used to define 100-year offshore conditions scenarios and to investigate the flood response to each scenario in terms of (1) maximum spatial extent of flooded areas, (2) volumes of water propagation inland and (3) water level in flooded areas. Scenarios of sea level rise are also considered in order to evaluate the potential hazard evolution. Our simulations show that for a maximising 100-year hazard scenario, for the municipality as a whole, 38 % of the affected zones are prone to overflow flooding and 62 % to flooding by propagation of overtopping water volume along the seafront. Results also reveal that for the two kinds of statistic scenarios a difference of about 5 % in the forcing conditions (water level, wave height and period) can produce significant differences in terms of flooding like +13.5 % of water volumes propagating inland or +11.3 % of affected surfaces. In some areas, flood response appears to be very sensitive to the chosen scenario with differences of 0.3 to 0.5 m in water level. The developed approach enables one to frame the 100-year hazard and to characterize spatially the robustness or the uncertainty over the results. Considering a 100-year scenario with mean sea level rise (0.6 m), hazard characteristics are dramatically changed with an evolution of the overtopping / overflowing process ratio and an increase of a factor 4.84 in volumes of water propagating inland and 3.47 in flooded surfaces.

Apparatus for controlling coolant level in a liquid-metal-cooled nuclear reactor

DOEpatents

Jones, Robert D.

1978-01-01

A liquid-metal-cooled fast-breeder reactor which has a thermal liner spaced inwardly of the pressure vessel and includes means for passing bypass coolant through the annulus between the thermal liner and the pressure vessel to insulate the pressure vessel from hot outlet coolant includes control ports in the thermal liner a short distance below the normal operating coolant level in the reactor and an overflow nozzle in the pressure vessel below the control ports connected to an overflow line including a portion at an elevation such that overflow coolant flow is established when the coolant level in the reactor is above the top of the coolant ports. When no makeup coolant is added, bypass flow is inwardly through the control ports and there is no overflow; when makeup coolant is being added, coolant flow through the overflow line will maintain the coolant level.

Improved Secret Image Sharing Scheme in Embedding Capacity without Underflow and Overflow.

PubMed

Pang, Liaojun; Miao, Deyu; Li, Huixian; Wang, Qiong

2015-01-01

Computational secret image sharing (CSIS) is an effective way to protect a secret image during its transmission and storage, and thus it has attracted lots of attentions since its appearance. Nowadays, it has become a hot topic for researchers to improve the embedding capacity and eliminate the underflow and overflow situations, which is embarrassing and difficult to deal with. The scheme, which has the highest embedding capacity among the existing schemes, has the underflow and overflow problems. Although the underflow and overflow situations have been well dealt with by different methods, the embedding capacities of these methods are reduced more or less. Motivated by these concerns, we propose a novel scheme, in which we take the differential coding, Huffman coding, and data converting to compress the secret image before embedding it to further improve the embedding capacity, and the pixel mapping matrix embedding method with a newly designed matrix is used to embed secret image data into the cover image to avoid the underflow and overflow situations. Experiment results show that our scheme can improve the embedding capacity further and eliminate the underflow and overflow situations at the same time.

Improved Secret Image Sharing Scheme in Embedding Capacity without Underflow and Overflow

PubMed Central

Pang, Liaojun; Miao, Deyu; Li, Huixian; Wang, Qiong

2015-01-01

Computational secret image sharing (CSIS) is an effective way to protect a secret image during its transmission and storage, and thus it has attracted lots of attentions since its appearance. Nowadays, it has become a hot topic for researchers to improve the embedding capacity and eliminate the underflow and overflow situations, which is embarrassing and difficult to deal with. The scheme, which has the highest embedding capacity among the existing schemes, has the underflow and overflow problems. Although the underflow and overflow situations have been well dealt with by different methods, the embedding capacities of these methods are reduced more or less. Motivated by these concerns, we propose a novel scheme, in which we take the differential coding, Huffman coding, and data converting to compress the secret image before embedding it to further improve the embedding capacity, and the pixel mapping matrix embedding method with a newly designed matrix is used to embed secret image data into the cover image to avoid the underflow and overflow situations. Experiment results show that our scheme can improve the embedding capacity further and eliminate the underflow and overflow situations at the same time. PMID:26351657

Observed and modelled stability of overflow across the Greenland-Scotland ridge.

PubMed

Olsen, Steffen M; Hansen, Bogi; Quadfasel, Detlef; Østerhus, Svein

2008-09-25

Across the Greenland-Scotland ridge there is a continuous flow of cold dense water, termed 'overflow', from the Nordic seas to the Atlantic Ocean. This is a main contributor to the production of North Atlantic Deep Water that feeds the lower limb of the Atlantic meridional overturning circulation, which has been predicted to weaken as a consequence of climate change. The two main overflow branches pass the Denmark Strait and the Faroe Bank channel. Here we combine results from direct current measurements in the Faroe Bank channel for 1995-2005 with an ensemble hindcast experiment for 1948-2005 using an ocean general circulation model. For the overlapping period we find a convincing agreement between model simulations and observations on monthly to interannual timescales. Both observations and model data show no significant trend in volume transport. In addition, for the whole 1948-2005 period, the model indicates no persistent trend in the Faroe Bank channel overflow or in the total overflow transport, in agreement with the few available historical observations. Deepening isopycnals in the Norwegian Sea have tended to decrease the pressure difference across the Greenland-Scotland ridge, but this has been compensated for by the effect of changes in sea level. In contrast with earlier studies, we therefore conclude that the Faroe Bank channel overflow, and also the total overflow, did not decrease consistently from 1950 to 2005, although the model does show a weakening total Atlantic meridional overturning circulation as a result of changes south of the Greenland-Scotland ridge.

Holocene multidecadal- to millennial-scale variations in Iceland-Scotland overflow and their relationship to climate

NASA Astrophysics Data System (ADS)

Mjell, Tor Lien; Ninnemann, Ulysses S.; Eldevik, Tor; Kleiven, Helga Kikki F.

2015-05-01

The Nordic Seas overflows are an important part of the Atlantic thermohaline circulation. While there is growing evidence that the overflow of dense water changed on orbital time scales during the Holocene, less is known about the variability on shorter time scales beyond the instrumental record. Here we reconstruct the relative changes in flow strength of Iceland-Scotland Overflow Water (ISOW), the eastern branch of the overflows, on multidecadal-millennial time scales. The reconstruction is based on mean sortable silt (SS>¯) from a sediment core on the Gardar Drift (60°19'N, 23°58'W, 2081 m). Our SS>¯ record reveals that the main variance in ISOW vigor occurred on millennial time scales (1-2 kyr) with particularly prominent fluctuations after 8 kyr. Superimposed on the millennial variability, there were multidecadal-centennial flow speed fluctuations during the early Holocene (10-9 kyr) and one prominent minimum at 0.9 kyr. We find a broad agreement between reconstructed ISOW and regional North Atlantic climate, where a strong (weak) ISOW is generally associated with warm (cold) climate. We further identify the possible contribution of anomalous heat and freshwater forcing, respectively, related to reconstructed overflow variability. We infer that ocean poleward heat transport can explain the relationship between regional climate and ISOW during the middle to late Holocene, whereas freshwater input provides a possible explanation for the reduced overflow during early Holocene (8-10 kyr).

Duration and Frequency Analysis of Lowland Flooding in Western Murfreesboro, Rutherford County, Tennessee, 1998-2000

USGS Publications Warehouse

Law, George S.

2002-01-01

Periodic flooding occurs at lowlands and sinkholes in and adjacent to the flood plain of the West Fork Stones River in the western part of Murfreesboro, Tennessee. Flooding in this area commonly occurs during the winter months from December through March. The maximum water level that flood waters will reach in a lowland or sinkhole is controlled by the elevation of the land surrounding the site or the overflow outlet. Maximum water levels, independent of overflow from the river, were estimated to be reached in lowlands and sinkholes in the study area every 1 to 4 years. Minor overflow from the West Fork Stones River (less than 1 foot in depth) into the study area has been estimated to occur every 10 to 20 years. Moderate overflow from the river (1 to 2 feet in depth) occurs on average every 20 to 50 years, while major river overflow (in excess of 2 feet in depth) can be expected every 50 years. Rainfall information for the area, and streamflow and water-level measurements from the West Fork Stones River, lowlands, sinkholes, caves, and wells in the study area were used to develop a flood-prone area map, independent of overflow from the river, for the study area. Water-level duration and frequency relations, independent of overflow from the river, were estimated for several lowlands, sinkholes, and wells in the study area. These relations are used to characterize flooding in lowland areas of western Murfreesboro, Rutherford County, Tennessee.

Prediction of Business Jet Airloads Using The Overflow Navier-Stokes Code

NASA Technical Reports Server (NTRS)

Bounajem, Elias; Buning, Pieter G.

2001-01-01

The objective of this work is to evaluate the application of Navier-Stokes computational fluid dynamics technology, for the purpose of predicting off-design condition airloads on a business jet configuration in the transonic regime. The NASA Navier-Stokes flow solver OVERFLOW with Chimera overset grid capability, availability of several numerical schemes and convergence acceleration techniques was selected for this work. A set of scripts which have been compiled to reduce the time required for the grid generation process are described. Several turbulence models are evaluated in the presence of separated flow regions on the wing. Computed results are compared to available wind tunnel data for two Mach numbers and a range of angles-of-attack. Comparisons of wing surface pressure from numerical simulation and wind tunnel measurements show good agreement up to fairly high angles-of-attack.

Reducing pathogens in combined sewer overflows using ozonation or UV irradiation.

PubMed

Tondera, Katharina; Klaer, Kassandra; Gebhardt, Jens; Wingender, Jost; Koch, Christoph; Horstkott, Marina; Strathmann, Martin; Jurzik, Lars; Hamza, Ibrahim Ahmed; Pinnekamp, Johannes

2015-11-01

Fecal contamination of water resources is a major public health concern in densely populated areas since these water bodies are used for drinking water production or recreational purposes. A main source of this contamination originates from combined sewer overflows (CSOs) in regions with combined sewer systems. Thus, the treatment of CSO discharges is urgent. In this study, we explored whether ozonation or UV irradiation can efficiently reduce pathogenic bacteria, viruses, and protozoan parasites in CSOs. Experiments were carried out in parallel settings at the outflow of a stormwater settling tank in the Ruhr area, Germany. The results showed that both techniques reduce most hygienically relevant bacteria, parasites and viruses. Under the conditions tested, ozonation yielded lower outflow values for the majority of the tested parameters. Copyright © 2015 Elsevier GmbH. All rights reserved.

A robust color signal processing with wide dynamic range WRGB CMOS image sensor

NASA Astrophysics Data System (ADS)

Kawada, Shun; Kuroda, Rihito; Sugawa, Shigetoshi

2011-01-01

We have developed a robust color reproduction methodology by a simple calculation with a new color matrix using the formerly developed wide dynamic range WRGB lateral overflow integration capacitor (LOFIC) CMOS image sensor. The image sensor was fabricated through a 0.18 μm CMOS technology and has a 45 degrees oblique pixel array, the 4.2 μm effective pixel pitch and the W pixels. A W pixel was formed by replacing one of the two G pixels in the Bayer RGB color filter. The W pixel has a high sensitivity through the visible light waveband. An emerald green and yellow (EGY) signal is generated from the difference between the W signal and the sum of RGB signals. This EGY signal mainly includes emerald green and yellow lights. These colors are difficult to be reproduced accurately by the conventional simple linear matrix because their wave lengths are in the valleys of the spectral sensitivity characteristics of the RGB pixels. A new linear matrix based on the EGY-RGB signal was developed. Using this simple matrix, a highly accurate color processing with a large margin to the sensitivity fluctuation and noise has been achieved.

Production of 2-Hydroxyisobutyric Acid from Methanol by Methylobacterium extorquens AM1 Expressing (R)-3-Hydroxybutyryl Coenzyme A-Isomerizing Enzymes

PubMed Central

Rohde, Maria-Teresa; Tischer, Sylvi; Harms, Hauke

2016-01-01

ABSTRACT The biotechnological production of the methyl methacrylate precursor 2-hydroxyisobutyric acid (2-HIBA) via bacterial poly-3-hydroxybutyrate (PHB) overflow metabolism requires suitable (R)-3-hydroxybutyryl coenzyme A (CoA)-specific coenzyme B12-dependent mutases (RCM). Here, we characterized a predicted mutase from Bacillus massiliosenegalensis JC6 as a mesophilic RCM closely related to the thermophilic enzyme previously identified in Kyrpidia tusciae DSM 2912 (M.-T. Weichler et al., Appl Environ Microbiol 81:4564–4572, 2015, https://doi.org/10.1128/AEM.00716-15). Using both RCM variants, 2-HIBA production from methanol was studied in fed-batch bioreactor experiments with recombinant Methylobacterium extorquens AM1. After complete nitrogen consumption, the concomitant formation of PHB and 2-HIBA was achieved, indicating that both sets of RCM genes were successfully expressed. However, although identical vector systems and incubation conditions were chosen, the metabolic activity of the variant bearing the RCM genes from strain DSM 2912 was severely inhibited, likely due to the negative effects caused by heterologous expression. In contrast, the biomass yield of the variant expressing the JC6 genes was close to the wild-type performance, and 2-HIBA titers of 2.1 g liter−1 could be demonstrated. In this case, up to 24% of the substrate channeled into overflow metabolism was converted to the mutase product, and maximal combined 2-HIBA plus PHB yields from methanol of 0.11 g g−1 were achieved. Reverse transcription-quantitative PCR analysis revealed that metabolic genes, such as methanol dehydrogenase and acetoacetyl-CoA reductase genes, are strongly downregulated after exponential growth, which currently prevents a prolonged overflow phase, thus preventing higher product yields with strain AM1. IMPORTANCE In this study, we genetically modified a methylotrophic bacterium in order to channel intermediates of its overflow metabolism to the C4 carboxylic acid 2-hydroxyisobutyric acid, a precursor of acrylic glass. This has implications for biotechnology, as it shows that reduced C1 substrates, such as methanol and formic acid, can be alternative feedstocks for producing today's commodities. We found that product titers and yields depend more on host physiology than on the activity of the introduced heterologous function modifying the overflow metabolism. In addition, we show that the fitness of recombinant strains substantially varies when they express orthologous genes from different origins. Further studies are needed to extend the overflow production phase in methylotrophic microorganisms for the implementation of biotechnological processes. PMID:27836853

A technique for fast and accurate measurement of hand volumes using Archimedes' principle.

PubMed

Hughes, S; Lau, J

2008-03-01

A new technique for measuring hand volumes using Archimedes principle is described. The technique involves the immersion of a hand in a water container placed on an electronic balance. The volume is given by the change in weight divided by the density of water. This technique was compared with the more conventional technique of immersing an object in a container with an overflow spout and collecting and weighing the volume of overflow water. The hand volume of two subjects was measured. Hand volumes were 494 +/- 6 ml and 312 +/- 7 ml for the immersion method and 476 +/- 14 ml and 302 +/- 8 ml for the overflow method for the two subjects respectively. Using plastic test objects, the mean difference between the actual and measured volume was -0.3% and 2.0% for the immersion and overflow techniques respectively. This study shows that hand volumes can be obtained more quickly than the overflow method. The technique could find an application in clinics where frequent hand volumes are required.

Distinct enantiomeric signals of ibuprofen and naproxen in treated wastewater and sewer overflow.

PubMed

Khan, Stuart J; Wang, Lili; Hashim, Nor H; McDonald, James A

2014-11-01

Ibuprofen and naproxen are commonly used members of a class of pharmaceuticals known as 2-arylpropionic acids (2-APAs). Both are chiral chemicals and can exist as either of two (R)- and (S)-enantiomers. Enantioselective analyses of effluents from municipal wastewater treatment plants (WWTPs) and from untreated sewage overflow reveal distinctly different enantiomeric fractions for both pharmaceuticals. The (S)-enantiomers of both were dominant in untreated sewage overflow, but the relative proportions of the (R)-enantiomers were shown to be increased in WWTP effluents. (R)-naproxen was below method detection limits (<1 ng.L(-1)) in sewage overflow, but measurable at higher concentrations in WWTP effluents. Accordingly, enantiomeric fractions (EF) for naproxen were consistently 1.0 in sewage overflow, but ranged from 0.7–0.9 in WWTP effluents. Ibuprofen EF ranged from 0.6–0.8 in sewage overflow and receiving waters, and was 0.5 in two WWTP effluents. Strong evidence is provided to indicate that chiral inversion of (S)-2-APAs to produce (R)-2-APAs may occur during wastewater treatment processes. It is concluded that this characterization of the enantiomeric fractions for ibuprofen and naproxen in particular effluents could facilitate the distinction of treated and untreated sources of pharmaceutical contamination in surface waters.

Variability of the Denmark Strait overflow: Moored time series from 1996-2011

NASA Astrophysics Data System (ADS)

Jochumsen, Kerstin; Quadfasel, Detlef; Valdimarsson, Heã°Inn; Jónsson, SteingríMur

2012-12-01

The Denmark Strait overflow provides about half of the total dense water overflow from the Nordic Seas into the North Atlantic Ocean. The velocity of the overflow has been monitored in the Strait with two moored Acoustic Doppler Current Profilers since 1996 with several interruptions due to mooring losses or instrument failure. So far, overflow transports were only calculated when data from both moorings were available. In this work, we introduce a linear model to fill gaps in the time series when data from only one instrument is available. The mean overflow transport is 3.4 Sv and exhibits a variance of 2.0 Sv2. No significant trend was detected in the time series. The highest variability in the transport is associated with the passage of mesoscale eddies with time scales of 2-10 days (associated with a variance of 1.5 Sv2). Seasonal variability is weak and explains less than 5% of the variance in all time series, which is in contrast to the strong seasonal cycle found in high resolution model simulations. Interannual variability is on the order of 10% of the mean. A relation to atmospheric forcing such as the local wind stress curl, as well as to larger scale phenomena, e.g. the North Atlantic Oscillation, is not detected. Since 2005 data from moored temperature, conductivity and pressure recorders have been available as well, monitoring the hydrographic variability at the bottom of Denmark Strait. In recent years the temperature time series of the Denmark Strait overflow revealed a cooling, while the salinity stayed nearly constant.

MK-801 protection against methamphetamine-induced striatal dopamine terminal injury is associated with attenuated dopamine overflow.

PubMed

Weihmuller, F B; O'Dell, S J; Marshall, J F

1992-06-01

Repeated administrations of methamphetamine (m-AMPH) produce high extracellular levels of dopamine (DA) and subsequent striatal DA terminal damage. Pharmacological blockade of N-methyl-D-aspartate (NMDA) receptors has been shown previously to prevent m-AMPH-induced striatal DA terminal injury, but the mechanism for this protection is unclear. In the present study, in vivo microdialysis was used to determine the effects of blockade of NMDA receptors with the noncompetitive antagonist MK-801 on m-AMPH-induced striatal DA overflow. Four injections of MK-801 (0.5 mg/kg, ip) alone did not significantly change extracellular striatal DA concentrations from pretreatment values. Four treatments with m-AMPH (4.0 mg/kg, sc at 2-hr intervals) increased striatal DA overflow, and the overflow was particularly extensive following the fourth injection. This m-AMPH regimen produced a 40% reduction in striatal DA tissue content 1 week later. Treatment with MK-801 15 min before each of the four m-AMPH injections or prior to only the last two m-AMPH administrations attenuated the m-AMPH-induced increase in striatal DA overflow and protected completely against striatal DA depletions. Other MK-801 treatment regimens less effectively reduced the m-AMPH-induced striatal DA efflux and were ineffective in protecting against striatal DA depletions. Linear regression analysis indicated that cumulative DA overflow was strongly predictive (r = -.68) of striatal DA tissue levels measured one week later. These findings suggest that the extensive DA overflow seen during a neurotoxic regimen of m-AMPH is a crucial component of the subsequent neurotoxicity.(ABSTRACT TRUNCATED AT 250 WORDS)

Orion Launch Abort Vehicle Separation Analysis Using OVERFLOW

NASA Technical Reports Server (NTRS)

Booth, Tom

2010-01-01

This slide presentation reviews the use of OVERFLOW, a flow solver, to analyze the effect of separation for a launch abort vehicle (i.e., Orion capsule) if required. Included in the presentation are views of the geometry, and the Overset grids, listing of the assumptions, the general run strategy, inputs into the Overflow solver, the required computational resources, the results of the convergence study. Charts and graphics are presented to show the results.

Effects of combined-sewer overflows and urban runoff on the water quality of Fall Creek, Indianapolis, Indiana

USGS Publications Warehouse

Martin, Jeffrey D.

1995-01-01

Concentrations of dissolved oxygen measured at the station in the middle of the combined-sewer overflows were less than the Indiana minimum ambient water-quality standard of 4.0 milligrams per liter during all storms. Concentrations of ammonia, oxygen demand, copper, lead, zinc, and fecal coliform bacteria at the stations downstream from the combined-sewer overflows were much higher in storm runoff than in base flow. Increased concentrations of oxygen demand in runoff probably were caused by combined-sewer overflows, urban runoff, and the resuspension of organic material deposited on the streambed. Some of the increased concentrations of lead, zinc, and probably copper can be attributed to the discharge and resuspension of filter backwash

Climate and hydrology of the last interglaciation (MIS 5) in Owens Basin, California: Isotopic and geochemical evidence from core OL-92

USGS Publications Warehouse

Li, H.-C.; Bischoff, J.L.; Ku, T.-L.; Zhu, Z.-Y.

2004-01-01

??18O, ??13C, total organic carbon, total inorganic carbon, and acid-leachable Li, Mg and Sr concentrations on 443 samples from 32 to 83 m depth in Owens Lake core OL-92 were analyzed to study the climatic and hydrological conditions between 60 and 155 ka with a resolution of ???200 a. The multi-proxy data show that Owens Lake overflowed during wet/cold conditions of marine isotope stages (MIS) 4, 5b and 6, and was closed during the dry/warm conditions of MIS 5a, c and e. The lake partially overflowed during MIS 5d. Our age model places the MIS 4/5 boundary at ca 72.5 ka and the MIS 5/6 boundary (Termination II) at ca 140 ka, agreeing with the Devils Hole chronology. The diametrical precipitation intensities between the Great Basin (cold/wet) and eastern China (cold/dry) on Milankovitch time scales imply a climatic teleconnection across the Pacific. It also probably reflects the effect of high-latitude ice sheets on the southward shifts of both the summer monsoon frontal zone in eastern Asia and the polar jet stream in western North America during glacial periods. ?? 2003 Elsevier Ltd. All rights reserved.

Removal of acetaminophen and naproxen by combined coagulation and adsorption using biochar: influence of combined sewer overflow components.

PubMed

Jung, Chanil; Oh, Jeill; Yoon, Yeomin

2015-07-01

The combined coagulation and adsorption of targeted acetaminophen and naproxen using activated biochar and aluminum sulfate were studied under various synthetic "combined sewer overflow" (CSO) conditions. The biochar demonstrated better adsorption performance for both acetaminophen and naproxen (removal, 94.1 and 97.7%, respectively) than that of commercially available powdered activated carbon (removal, 81.6 and 94.1%, respectively) due to superior carbonaceous structure and surface properties examined by nuclear magnetic resonance analysis. The adsorption of naproxen was more favorable, occupying active adsorption sites on the adsorbents by naproxen due to its higher adsorption affinity compared to acetaminophen. Three classified CSO components (i.e., representing hydrophobic organics, hydrophilic organics, and inorganics) played different roles in the adsorption of both adsorbates, resulted in inhibition by humic acid complexation or metal ligands and negative electrostatic repulsion under adsorption and coagulation combined system. Adsorption alone with biochar was determined to be the most effective adsorptive condition for the removal of both acetaminophen and naproxen under various CSO conditions, while both coagulation alone and combined adsorption and coagulation failed to remove the acetaminophen and naproxen adequately due to an increase in ionic strength in the presence of spiked aluminum species derived from the coagulant.

Teaching in the Land of Happiness: The Canada-Bhutan Connection

ERIC Educational Resources Information Center

Scott, Kristen

2011-01-01

Classrooms in Bhutan overflow with eager students; however, the teacher supply is often not enough to meet demand. The Bhutan Canada Foundation (BCF) is a Canadian charity working with the Ministry of Education in Bhutan, providing Canadian teachers to remote areas, where they work for a local salary and live in basic conditions The feature of…

Simulation of Jet Noise with OVERFLOW CFD Code and Kirchhoff Surface Integral

NASA Technical Reports Server (NTRS)

Kandula, M.; Caimi, R.; Voska, N. (Technical Monitor)

2002-01-01

An acoustic prediction capability for supersonic axisymmetric jets was developed on the basis of OVERFLOW Navier-Stokes CFD (Computational Fluid Dynamics) code of NASA Langley Research Center. Reynolds-averaged turbulent stresses in the flow field are modeled with the aid of Spalart-Allmaras one-equation turbulence model. Appropriate acoustic and outflow boundary conditions were implemented to compute time-dependent acoustic pressure in the nonlinear source-field. Based on the specification of acoustic pressure, its temporal and normal derivatives on the Kirchhoff surface, the near-field and the far-field sound pressure levels are computed via Kirchhoff surface integral, with the Kirchhoff surface chosen to enclose the nonlinear sound source region described by the CFD code. The methods are validated by a comparison of the predictions of sound pressure levels with the available data for an axisymmetric turbulent supersonic (Mach 2) perfectly expanded jet.

Simulation of Supersonic Jet Noise with the Adaptation of Overflow CFD Code and Kirchhoff Surface Integral

NASA Technical Reports Server (NTRS)

Kandula, Max; Caimi, Raoul; Steinrock, T. (Technical Monitor)

2001-01-01

An acoustic prediction capability for supersonic axisymmetric jets was developed on the basis of OVERFLOW Navier-Stokes CFD (Computational Fluid Dynamics) code of NASA Langley Research Center. Reynolds-averaged turbulent stresses in the flow field are modeled with the aid of Spalart-Allmaras one-equation turbulence model. Appropriate acoustic and outflow boundary conditions were implemented to compute time-dependent acoustic pressure in the nonlinear source-field. Based on the specification of acoustic pressure, its temporal and normal derivatives on the Kirchhoff surface, the near-field and the far-field sound pressure levels are computed via Kirchhoff surface integral, with the Kirchhoff surface chosen to enclose the nonlinear sound source region described by the CFD code. The methods are validated by a comparison of the predictions of sound pressure levels with the available data for an axisymmetric turbulent supersonic (Mach 2) perfectly expanded jet.

Iceland-Scotland Overflow Water transport variability through the Charlie-Gibbs Fracture Zone and the impact of the North Atlantic Current

NASA Astrophysics Data System (ADS)

Bower, Amy; Furey, Heather

2017-09-01

The Charlie-Gibbs Fracture Zone (CGFZ), a deep and wide gap in the Mid-Atlantic Ridge near 52°N, is a gateway between the eastern and western subpolar regions for the Atlantic Meridional Overturning Circulation (AMOC). In 2010-2012, an eight-mooring array of current meters and temperature/salinity sensors was installed across the CGFZ between 500 m and the sea floor to measure the mean transport of westward-flowing Iceland-Scotland Overflow Water (ISOW) and investigate the impact of the eastward-flowing North Atlantic Current (NAC) on ISOW transport variability. The 22 month record mean ISOW transport through the CGFZ, -1.7 ± 0.5 Sv (95% confidence interval), is 30% lower than the previously published estimate based on 13 months of current-only measurements, -2.4 ± 1.2 Sv. The latter mean estimate may have been biased high due to the lack of continuous salinity measurements, although the two estimates are not statistically different due to strong mesoscale variability in both data sets. Empirical Orthogonal Function analysis and maps of satellite-derived absolute dynamic topography show that weak westward ISOW transport events and eastward reversals are caused by northward meanders of the NAC, with its deep-reaching eastward velocities. These results add to growing evidence that a significant fraction of ISOW exits the Iceland Basin by routes other than the CGFZ.

Industrial Application of Valuable Materials Generated from PLK Rock-A Bauxite Mining Waste

NASA Astrophysics Data System (ADS)

Swain, Ranjita; Routray, Sunita; Mohapatra, Abhisek; Ranjan Patra, Biswa

2018-03-01

PLK rock classified in to two products after a selective grinding to a particular size fraction. PLK rocks ground to below 45-micron size which is followed by a classifier i.e. hydrocyclone. The ground product classified in to different sizes of apex and vortex finder. The pressure gauge was attached for the measurement of the pressure. The production of fines is also increasing with increase in the vortex finder diameter. In order to increase in the feed capacity of the hydrocyclone, the vortex finder 11.1 mm diameter and the spigot diameter 8.0 mm has been considered as the best optimum condition for recovery of fines from PLK rock sample. The overflow sample contains 5.39% iron oxide (Fe2O3) with 0.97% of TiO2 and underflow sample contains 1.87% Fe2O3 with 2.39% of TiO2. The cut point or separation size of overflow sample is 25 μm. The efficiency of separation, or the so-called imperfection I, is at 6 μm size. In this study, the iron oxide content in underflow sample is less than 2% which is suitable for making of refractory application. The overflow sample is very fine which can also be a raw material for ceramic industry as well as a cosmetic product.

Valve for controlling solids flow

DOEpatents

Staiger, M. Daniel

1985-01-01

A valve for controlling the flow of solids comprises a vessel having an overflow point, an inlet line for discharging solids into the vessel positioned within the vessel such that the inlet line's discharge point is lower than the vessel's overflow point, and apparatus for introducing a fluidizing fluid into the vessel. The fluidizing fluid fluidizes the solids within the vessel so that they overflow at the vessel's overflow point. For the removal of nuclear waste product the vessel may be placed within a sealed container having a bottom connected transport line for transporting the solids to storage or other sites. The rate of solids flow is controlled by the flow rate of the fluidizing fluid and by V-notch weirs of different sizes spaced about the top of the vessel.

Valve for controlling solids flow

DOEpatents

Staiger, M.D.

1982-09-29

A valve for controlling the flow of solids comprises a vessel having an overflow point, an inlet line for discharging solids into the vessel positioned within the vessel such that the inlet line's discharge point is lower than the vessel's overflow point, and means for introducing a fluidizing fluid into the vessel. The fluidizing fluid fluidizes the solids within the vessel so that they overflow at the vessel's overflow point. For the removal of nuclear waste product the vessel may be placed within a sealed container having a bottom connected transport line for transporting the solids to storage or other sites. The rate of solids flow is controlled by the flow rate of the fluidizing fluid and by V-notch weirs of different sizes spaced about the top of the vessel.

Flu Widget

MedlinePlus

... 0" width="300" title="Flu I.Q. Widget" style="overflow: hidden;"> Flu ... 0" width="280" title="CDC Flu Vaccine Finder" style="overflow: hidden;"> FluView Widget < ...

Characterizing the scientific potential of satellite sensors. [San Francisco, California

NASA Technical Reports Server (NTRS)

1984-01-01

Eleven thematic mapper (TM) radiometric calibration programs were tested and evaluated in support of the task to characterize the potential of LANDSAT TM digital imagery for scientific investigations in the Earth sciences and terrestrial physics. Three software errors related to integer overflow, divide by zero, and nonexist file group were found and solved. Raw, calibrated, and corrected image groups that were created and stored on the Barker2 disk are enumerated. Black and white pixel print files were created for various subscenes of a San Francisco scene (ID 40392-18152). The development of linear regression software is discussed. The output of the software and its function are described. Future work in TM radiometric calibration, image processing, and software development is outlined.

Drag Prediction for the DLR-F6 Wing/Body and DPW Wing using CFL3D and OVERFLOW Overset Mesh

NASA Technical Reports Server (NTRS)

Sclanfani, Anthony J.; Vassberg, John C.; Harrison, Neal A.; DeHaan, Mark A.; Rumsey, Christopher L.; Rivers, S. Melissa; Morrison, Joseph H.

2007-01-01

A series of overset grids was generated in response to the 3rd AIAA CFD Drag Prediction Workshop (DPW-III) which preceded the 25th Applied Aerodynamics Conference in June 2006. DPW-III focused on accurate drag prediction for wing/body and wing-alone configurations. The grid series built for each configuration consists of a coarse, medium, fine, and extra-fine mesh. The medium mesh is first constructed using the current state of best practices for overset grid generation. The medium mesh is then coarsened and enhanced by applying a factor of 1.5 to each (I,J,K) dimension. The resulting set of parametrically equivalent grids increase in size by a factor of roughly 3.5 from one level to the next denser level. CFD simulations were performed on the overset grids using two different RANS flow solvers: CFL3D and OVERFLOW. The results were post-processed using Richardson extrapolation to approximate grid converged values of lift, drag, pitching moment, and angle-of-attack at the design condition. This technique appears to work well if the solution does not contain large regions of separated flow (similar to that seen n the DLR-F6 results) and appropriate grid densities are selected. The extra-fine grid data helped to establish asymptotic grid convergence for both the OVERFLOW FX2B wing/body results and the OVERFLOW DPW-W1/W2 wing-alone results. More CFL3D data is needed to establish grid convergence trends. The medium grid was utilized beyond the grid convergence study by running each configuration at several angles-of-attack so drag polars and lift/pitching moment curves could be evaluated. The alpha sweep results are used to compare data across configurations as well as across flow solvers. With the exception of the wing/body drag polar, the two codes compare well qualitatively showing consistent incremental trends and similar wing pressure comparisons.

Variability in form and growth of sediment waves on turbidite channel levees

USGS Publications Warehouse

Normark, W.R.; Piper, D.J.W.; Posamentier, H.; Pirmez, C.; Migeon, S.

2002-01-01

Fine-grained sediment waves have been observed in many modern turbidite systems, generally restricted to the overbank depositional element. Sediment waves developed on six submarine fan systems are compared using high-resolution seismic-reflection profiles, sediment core samples (including ODP drilling), multibeam bathymetry, 3D seismic-reflection imaging (including examples of burried features), and direct measurements of turbidity currents that overflow their channels. These submarine fan examples extend over more than three orders of magnitude in physical scale. The presence or absence of sediment waves is not simply a matter of either the size of the turbidite channel-levee systems or the dominant initiation process for the turbidity currents that overflow the channels to form the wave fields. Both sediment-core data and seismic-reflection profiles document the upslope migration of the wave forms, with thicker and coarser beds deposited on the up-current flank of the waves. Some wave fields are orthogonal to channel trend and were initiated by large flows whose direction was controlled by upflow morphology, whereas fields subparallel to channel levees resulted from local spillover. In highly meandering systems, sediment waves may mimic meander planform. Larger sediment waves form on channel-levee systems with thicker overflow of turbidity currents, but available data indicate that sediment waves can be maintaned during conditions of relatively thin overflow. Coarser-grained units in sediment waves are typically laminated and thin-bedded sand as much as several centimetres thick, but sand beds as thick as several tens of centimetres have been documented from both modern and buried systems. Current production of hydrocarbons from sediment-wave deposits suggests that it is important to develop criteria for recognising this overbank element in outcrop exposures and borehole data, where the wavelength of typical waves (several kilometres) generally exceeds outcrop scales and wave heights, which are reduced as a result of consolidation during burial, may be too subtle to recognise. Crown Copyright ?? 2002 Published by Elsevier Science B.V. All rights reserved.

Quantitative and qualitative assessment of the impact of climate change on a combined sewer overflow and its receiving water body.

PubMed

Bi, Eustache Gooré; Monette, Frédéric; Gachon, Philippe; Gaspéri, Johnny; Perrodin, Yves

2015-08-01

Projections from the Canadian Regional Climate Model (CRCM) for the southern part of the province of Québec, Canada, suggest an increase in extreme precipitation events for the 2050 horizon (2041-2070). The main goal of this study consisted in a quantitative and qualitative assessment of the impact of the 20 % increase in rainfall intensity that led, in the summer of 2013, to overflows in the "Rolland-Therrien" combined sewer system in the city of Longueuil, Canada. The PCSWMM 2013 model was used to assess the sensitivity of this overflow under current (2013) and future (2050) climate conditions. The simulated quantitative variables (peak flow, Q(CSO), and volume discharged, VD) served as the basis for deriving ecotoxicological risk indices and event fluxes (EFs) transported to the St. Lawrence (SL) River. Results highlighted 15 to 500% increases in VD and 13 to 148% increases in Q(CSO) by 2050 (compared to 2013), based on eight rainfall events measured from May to October. These results show that (i) the relationships between precipitation and combined sewer overflow variables are not linear and (ii) the design criteria for current hydraulic infrastructure must be revised to account for the impact of climate change (CC) arising from changes in precipitation regimes. EFs discharged into the SL River will be 2.24 times larger in the future than they are now (2013) due to large VDs resulting from CC. This will, in turn, lead to excessive inputs of total suspended solids (TSSs) and tracers for numerous urban pollutants (organic matter and nutrients, metals) into the receiving water body. Ecotoxicological risk indices will increase by more than 100% by 2050 compared to 2013. Given that substantial VDs are at play, and although CC scenarios have many sources of uncertainty, strategies to adapt this drainage network to the effects of CC will have to be developed.

36 CFR 261.77 - Prohibitions in Region 8, Southern Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Ford, Sandy Ford, Highway 76, Woodall Shoals, or Overflow Bridge or unless authorized under special use... Bridge, Earl's Ford, Sandy Ford, Highway 76, Woodall Shoals, or Overflow Bridge or unless authorized...

Wintertime re-ventilation of the East Greenland Current's Atlantic-origin Overflow Water in the western Iceland Sea

NASA Astrophysics Data System (ADS)

Våge, Kjetil; Håvik, Lisbeth; Papritz, Lukas; Spall, Michael; Moore, Kent

2017-04-01

The Deep Western Boundary Current constitutes the lower limb of the Atlantic Meridional Overturning Circulation, and, as such, is a crucial component of the Earth's climate system. The largest and densest contribution to the current stems from the overflow plume that passes through Denmark Strait. A main source of Denmark Strait Overflow Water (DSOW) is the East Greenland Current (EGC). The DSOW transported by the EGC originates from the Atlantic inflow into the Nordic Seas. This is then transformed into Atlantic-origin Overflow Water while progressing northward through the eastern part of the Nordic Seas. Here we show, using measurements from autonomous gliders deployed from fall 2015 to spring 2016, that the Atlantic-origin Overflow Water transported toward Denmark Strait by the EGC was re-ventilated while transiting the western Iceland Sea in winter. In summer, this region is characterized by an upper layer of cold, fresh Polar Surface Water that is thought to prevent convection. But in fall and winter this fresh water mass is diverted toward the Greenland shelf by enhanced northerly winds, which results in a water column that is preconditioned for convection. Severe heat loss from the ocean to the atmosphere offshore of the ice edge subsequently causes the formation of deep mixed layers. This further transforms the Atlantic-origin Overflow Water and impacts the properties of the DSOW, and hence the deepest and densest component of the lower limb of the Atlantic Meridional Overturning Circulation.

Currents and Mixing in the San Lorenzo Overflow, Northern Gulf of California

NASA Astrophysics Data System (ADS)

Rosas-Villegas, Froylán.; López, Manuel; Candela, Julio

2018-02-01

The main properties of the San Lorenzo (SL) overflow are studied, using data from two nonsimultaneous ADCP moorings (located at the sill, and 5 km downstream), as well as CTD and LADCP profiles. Strong tidal currents at the sill modulate the overflow, which is not shut down during the neaps. At the downstream site, the largest flood currents are associated with colder water advected from the sill, flowing downslope, and creating an asymmetry in the semidiurnal tidal cycle. The overflow introduces a significant fortnightly harmonic at the downstream site, and delays the M2 tidal currents for more than an hour with respect to the currents at the sill. The overflow mixes with the overlying water by entrainment during its supercritical stage, reaching near-bottom velocities as high as 1.5 ms-1 and an estimated mean transport of 0.11 Sv; almost twice that estimated at the sill for the same period of the year. Estimated Froude numbers during spring tides suggest the development of an internal hydraulic jump. After relaxation of the maximum downstream currents, high-frequency temperature fluctuations, likely linked to upstream traveling waves, are consistently observed. Direct estimations of the turbulent dissipation rates were used to compute diapycnal diffusivity (Kρ) profiles. Mean estimates of Kρ, as high as 5.5 × 10-2 m2s-1, show that shear at the interface is the most significant source of cross-isopycnal mixing along the SL overflow during ebb tides.

A study of overflow simulations using MPAS-Ocean: Vertical grids, resolution, and viscosity

NASA Astrophysics Data System (ADS)

Reckinger, Shanon M.; Petersen, Mark R.; Reckinger, Scott J.

2015-12-01

MPAS-Ocean is used to simulate an idealized, density-driven overflow using the dynamics of overflow mixing and entrainment (DOME) setup. Numerical simulations are carried out using three of the vertical coordinate types available in MPAS-Ocean, including z-star with partial bottom cells, z-star with full cells, and sigma coordinates. The results are first benchmarked against other models, including the MITgcm's z-coordinate model and HIM's isopycnal coordinate model, which are used to set the base case used for this work. A full parameter study is presented that looks at how sensitive overflow simulations are to vertical grid type, resolution, and viscosity. Horizontal resolutions with 50 km grid cells are under-resolved and produce poor results, regardless of other parameter settings. Vertical grids ranging in thickness from 15 m to 120 m were tested. A horizontal resolution of 10 km and a vertical resolution of 60 m are sufficient to resolve the mesoscale dynamics of the DOME configuration, which mimics real-world overflow parameters. Mixing and final buoyancy are least sensitive to horizontal viscosity, but strongly sensitive to vertical viscosity. This suggests that vertical viscosity could be adjusted in overflow water formation regions to influence mixing and product water characteristics. Lastly, the study shows that sigma coordinates produce much less mixing than z-type coordinates, resulting in heavier plumes that go further down slope. Sigma coordinates are less sensitive to changes in resolution but as sensitive to vertical viscosity compared to z-coordinates.

Advanced Concepts Research Initiative

EPA Science Inventory

This initiative is investigating various approaches to controlling and treating wet-weather flow (WWF) discharges in the urban watershed. WWF, including combined sewer overflow (CSO), sanitary sewer overflow (SSO) and stormwater discharges are leading causes of receiving water q...

A Screening Assessment of the Potential Impacts of Climate ...

EPA Pesticide Factsheets

EPA announced the availability of the report, A Screening Assessment of the Potential Impacts of Climate Change on Combined Sewer Overflow (CSO) Mitigation in the Great Lakes and New England Regions. This report is a screening-level assessment of the potential implications climate change has had on combined sewer overflow (CSO) mitigation in the Great Lakes and New England Regions. This report describes the potential scope and magnitude of climate change impacts on combined sewer overflow (CSOs) mitigation efforts in the Great Lakes Region and New England Region.

PX Andromedae and the SW Sextantis phenomenon

NASA Technical Reports Server (NTRS)

Hellier, Coel; Robinson, E. L.

1994-01-01

We show that the emission-line peculiarities of PX And and other SW Sex stars can be explained by an accretion stream which overflows the initial impact with the accretion disk and continues to a later reimpact. The overflowing stream is seen projected against a brighter disk and produces the 'phase 0.5 absorption' features. Emission from the reimpact site produces the high-velocity line wings which alternate from red to blue on the orbital cycle. We conclude that substantial disk overflow is the property distinguishing SW Sex stars from other cataclysmic variables.

Incision of Licus Vallis, Mars, From Multiple Lake Overflow Floods

NASA Astrophysics Data System (ADS)

Goudge, Timothy A.; Fassett, Caleb I.

2018-02-01

Licus Vallis is a large valley (>350 km long, >2 km wide, and >150 m deep) that heads at the outlet breach of an 30 km diameter impact crater. We present observations of the geomorphology and topography of this paleolake outlet valley and associated tributary valleys to constrain the history of incision of the Licus Vallis system. Licus Vallis has an abrupt increase in gradient by a factor of approximately 4 along its longitudinal profile, and a knickpoint that drops 200 m over a reach of 2 km approximately 12 km downstream from the valley head. We also describe a set of paired terraces within Licus Vallis, which are continuous for tens of kilometers and define an interior valley >2 km in width. We interpret the geomorphology of Licus Vallis as recording at least two discrete, major episodes of valley incision, both driven by lake overflow floods. The main portion of Licus Vallis formed by overflow flooding from a large ( 103-104 km2) lake contained in an intercrater basin. Subsequently, overflow flooding from a lake within the 30 km diameter impact crater reactivated Licus Vallis, forming a major knickpoint at the valley head and establishing the upstream section of the valley at a lower slope. Farther down the valley, this flood event incised an interior valley bounded by paired terraces. Regional tributary valleys that feed Licus Vallis also have prominent knickpoints, which have retreated farthest for downstream valleys. We conclude that these knickpoints record successive waves of incision that swept up Licus Vallis during lake overflow flooding, with erosion in the main trunk of the valley (from overflow floods) significantly outpacing erosion in the tributary valleys (from regional surface runoff). These observations of Licus Vallis illustrate how lake overflow floods may have provided an important control on the pace of landscape evolution on Mars.

USEPA CAPSTONE REPORT: DISINFECTION

EPA Science Inventory

Wet-weather flow (WWF), including combined-sewer overflow (CSO), sanitary-sewer overflow, and stormwater (SW) is a significant contributor of microbial contamination to surface water and ground water. Contamination with human-origin fecal coliform (FC) is of great concern for san...

VERIFICATION OF HIGH-RATE DISINFECTION TECHNOLOGIES FOR WET-WEATHER FLOWS

EPA Science Inventory

This paper describes the critical components of the USEPA's Environmental Technology Verification Program for two specific technologies categories: ultraviolet disinfection technologies for treating combined sewer overflow (CSO) and sanitary sewer overflow (SSO), and; induction m...

OPTIMIZATION OF COMBINED SEWER OVERFLOW CONTROL SYSTEMS

EPA Science Inventory

The highly variable and intermittent pollutant concentrations and flowrates associated with wet-weather events in combined sewersheds necessitates the use of storage-treatment systems to control pollution.An optimized combined-sewer-overflow (CSO) control system requires a manage...

MANAGEMENT OF COMBINED SEWER OVERFLOW: RESEARCH PROGRAM CAPSTONE

EPA Science Inventory

Combined-sewer overflow (CSO) is a mixture of urban storm drainage, municipal-industrial wastewater, and subterranean infiltration. Untreated discharges of CSOs have caused substantial pollution impacts on the quality of receiving-water bodies. Problem constituents include visi...

MANAGEMENT OF COMBINED SEWER OVERFLOW RESEARCH PROGRAM CAPSTONE

EPA Science Inventory

Combined-sewer overflow (CSO) is a mixture of urban storm drainage, municipal-industrial wastewater, and subterranean infiltration. Untreated discharges of CSOs have caused substantial pollution impacts on the quality of receiving-water bodies. Problem constituents include ...

Numerical simulation of overflow at vertical weirs using a hybrid level set/VOF method

NASA Astrophysics Data System (ADS)

Lv, Xin; Zou, Qingping; Reeve, Dominic

2011-10-01

This paper presents the applications of a newly developed free surface flow model to the practical, while challenging overflow problems for weirs. Since the model takes advantage of the strengths of both the level set and volume of fluid methods and solves the Navier-Stokes equations on an unstructured mesh, it is capable of resolving the time evolution of very complex vortical motions, air entrainment and pressure variations due to violent deformations following overflow of the weir crest. In the present study, two different types of vertical weir, namely broad-crested and sharp-crested, are considered for validation purposes. The calculated overflow parameters such as pressure head distributions, velocity distributions, and water surface profiles are compared against experimental data as well as numerical results available in literature. A very good quantitative agreement has been obtained. The numerical model, thus, offers a good alternative to traditional experimental methods in the study of weir problems.

Cathodal transcranial direct current stimulation in children with dystonia: a pilot open-label trial.

PubMed

Young, Scott J; Bertucco, Matteo; Sheehan-Stross, Rebecca; Sanger, Terence D

2013-10-01

Studies suggest that dystonia is associated with increased motor cortex excitability. Cathodal transcranial direct current stimulation can temporarily reduce motor cortex excitability. To test whether stimulation of the motor cortex can reduce dystonic symptoms in children, we measured tracking performance and muscle overflow using an electromyogram tracking task before and after stimulation. Of 10 participants, 3 showed a significant reduction in overflow, and a fourth showed a significant reduction in tracking error. Overflow decreased more when the hand contralateral to the cathode performed the task than when the hand ipsilateral to the cathode performed the task. Averaged over all participants, the results did not reach statistical significance. These results suggest that cathodal stimulation may allow a subset of children to control muscles or reduce involuntary overflow activity. Further testing is needed to confirm these results in a blinded trial and identify the subset of children who are likely to respond.

Excessive motor overflow reveals abnormal inter-hemispheric connectivity in Friedreich ataxia.

PubMed

Low, Sze-Cheen; Corben, Louise A; Delatycki, Martin B; Ternes, Anne-Marie; Addamo, Patricia K; Georgiou-Karistianis, Nellie

2013-07-01

This study sought to characterise force variability and motor overflow in 12 individuals with Friedreich ataxia (FRDA) and 12 age- and gender-matched controls. Participants performed a finger-pressing task by exerting 30 and 70 % of their maximum finger force using the index finger of the right and left hand. Control of force production was measured as force variability, while any involuntary movements occurring on the finger of the other, passive hand, was measured as motor overflow. Significantly greater force variability in individuals with FRDA compared with controls is indicative of cortico-cerebellar disruption affecting motor control. Meanwhile, significantly greater motor overflow in this group provides the first evidence of possible abnormal inter-hemispheric activity that may be attributable to asymmetrical neuronal loss in the dentate nucleus. Overall, this study demonstrated a differential engagement in the underlying default processes of the motor system in FRDA.

Hand digit control in children: motor overflow in multi-finger pressing force vector space during maximum voluntary force production.

PubMed

Shim, Jae Kun; Karol, Sohit; Hsu, Jeffrey; de Oliveira, Marcio Alves

2008-04-01

The aim of this study was to investigate the contralateral motor overflow in children during single-finger and multi-finger maximum force production tasks. Forty-five right handed children, 5-11 years of age produced maximum isometric pressing force in flexion or extension with single fingers or all four fingers of their right hand. The forces produced by individual fingers of the right and left hands were recorded and analyzed in four-dimensional finger force vector space. The results showed that increases in task (right) hand finger forces were linearly associated with non-task (left) hand finger forces. The ratio of the non-task hand finger force magnitude to the corresponding task hand finger force magnitude, termed motor overflow magnitude (MOM), was greater in extension than flexion. The index finger flexion task showed the smallest MOM values. The similarity between the directions of task hand and non-task hand finger force vectors in four-dimensional finger force vector space, termed motor overflow direction (MOD), was the greatest for index and smallest for little finger tasks. MOM of a four-finger task was greater than the sum of MOMs of single-finger tasks, and this phenomenon was termed motor overflow surplus. Contrary to previous studies, no single-finger or four-finger tasks showed significant changes of MOM or MOD with the age of children. We conclude that the contralateral motor overflow in children during finger maximum force production tasks is dependent upon the task fingers and the magnitude and direction of task finger forces.

UV Disinfection of Wastewater and Combined Sewer Overflows.

PubMed

Gibson, John; Drake, Jennifer; Karney, Bryan

2017-01-01

Municipal wastewater contains bacteria, viruses, and other pathogens that adversely affect the environment, human health, and economic activity. One way to mitigate these effects is a final disinfection step using ultraviolet light (UVL). The advantages of UVL disinfection, when compared to the more traditional chlorine, include no chlorinated by-products, no chemical residual, and relatively compact size. The design of most UV reactors is complex. It involves lamp selection, power supply design, optics, and hydraulics. In general, medium pressure lamps are more compact, powerful, and emit over a wider range of light than the more traditional low pressure lamps. Low pressure lamps, however, may be electrically more efficient. In UV disinfection, the fraction of surviving organisms (e.g. E. coli) will decrease exponentially with increasing UV dose. However, the level of disinfection that can be achieved is often limited by particle-associated organisms. Efforts to remove or reduce the effects of wastewater particles will often improve UV disinfection effectiveness. Regrowth, photoreactivation, or dark repair after UV exposure are sometimes cited as disadvantages of UV disinfection. Research is continuing in this area, however there is little evidence that human pathogens can photoreactivate in environmental conditions, at doses used in wastewater treatment. The UV disinfection of combined sewer overflows, a form of wet weather pollution, is challenging and remains largely at the research phase. Pre-treatment of combined sewer overflows (CSOs) with a cationic polymer to induce fast settling, and a low dose of alum to increase UV transmittance, has shown promise at the bench scale.

Emerging Contaminants in Wet-Weather Flow: Characterization and Treatability

EPA Science Inventory

An extensive literature review was conducted on the presence and magnitude of emerging contaminants (ECs) in wet-weather flow (WWF) including separate stormwater, combined sewer overflow (CSO), and sanitary sewer overflow (SSO). Although little information exists for stormwater ...

URBAN RUNOFF POLLUTION CONTROL - STATE-OF-THE-ART

EPA Science Inventory

Combined sewer overflows are major sources of water pollution problems, but even discharges of stormwater alone can seriously affect water quality. Current approaches involve control of overflows, treatment, and combinations of the two. Control may involve maximizing treatment wi...

VERIFICATION OF HIGH-RATE DISINFECTION TECHNOLOGIES FOR WET-WEATHER FLOW APPLICATIONS

EPA Science Inventory

This paper describes the critical components of the USEPA's Environmental Technology Verification Program for two specific technologies categories: ultraviolet disinfection technologies for treating combined sewer overflow (CSO) and sanitary sewer overflow (SSO), and; and mechani...

2. PLANK WALKWAY ATOP PIPE, ALSO SHOWING OVERFLOW CONTROL BOX ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. PLANK WALKWAY ATOP PIPE, ALSO SHOWING OVERFLOW CONTROL BOX AT JUNCTION OF PIPE WITH CONCRETE CHANNEL TO FISH SCREEN. VIEW TO NORTHEAST. - Santa Ana River Hydroelectric System, Pipeline to Fish Screen, Redlands, San Bernardino County, CA

Implementation of Premixed Equilibrium Chemistry Capability in OVERFLOW

NASA Technical Reports Server (NTRS)

Olsen, M. E.; Liu, Y.; Vinokur, M.; Olsen, T.

2003-01-01

An implementation of premixed equilibrium chemistry has been completed for the OVERFLOW code, a chimera capable, complex geometry flow code widely used to predict transonic flowfields. The implementation builds on the computational efficiency and geometric generality of the solver.

Implementation of Premixed Equilibrium Chemistry Capability in OVERFLOW

NASA Technical Reports Server (NTRS)

Olsen, Mike E.; Liu, Yen; Vinokur, M.; Olsen, Tom

2004-01-01

An implementation of premixed equilibrium chemistry has been completed for the OVERFLOW code, a chimera capable, complex geometry flow code widely used to predict transonic flowfields. The implementation builds on the computational efficiency and geometric generality of the solver.

HIGH-RATE DISINFECTION TECHNIQUES FOR COMBIND SEWER OVERFLOW

EPA Science Inventory

This paper presents high-rate disinfection technologies for combined sewer overflow (CSO). The high-rate disinfection technologies of interest are: chlorination/dechlorination, ultraviolet light irradiation (UV), chlorine dioxide (ClO2 ), ozone (O3), peracetic acid (CH3COOOH )...

76 FR 63954 - Notice of Lodging of Consent Decree Under the Clean Water Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-14

... overflows and correcting the effluent limitation violations. The City will comply with a mutually agreed... report on the status of any overflows from the Combined Sewer System (``CSS'') and their duration and...

GOES-R: Satellite Insight

NASA Technical Reports Server (NTRS)

Fitzpatrick, Austin J.; Leon, Nancy J.; Novati, Alexander; Lincoln, Laura K.; Fisher, Diane K.

2012-01-01

GOES-R: Satellite Insight seeks to bring awareness of the GOES-R (Geostationary Operational Environmental Satellite -- R Series) satellite currently in development to an audience of all ages on the emerging medium of mobile games. The iPhone app (Satellite Insight) was created for the GOES-R Program. The app describes in simple terms the types of data products that can be produced from GOES-R measurements. The game is easy to learn, yet challenging for all audiences. It includes educational content and a path to further information about GOESR, its technology, and the benefits of the data it collects. The game features action-puzzle game play in which the player must prevent an overflow of data by matching falling blocks that represent different types of GOES-R data. The game adds more different types of data blocks over time, as long as the player can prevent a data overflow condition. Points are awarded for matches, and players can compete with themselves to beat their highest score.

Glycogen Synthesis and Metabolite Overflow Contribute to Energy Balancing in Cyanobacteria

DOE PAGES

Cano, Melissa A.; Holland, Steven C.; Artier, Juliana; ...

2018-04-17

Understanding how living cells manage high-energy metabolites such as ATP and NADPH is essential for understanding energy transformations in the biosphere. Using light as the energy input, we find that energy charge (ratio of ATP over ADP+ATP) in the cyanobacterium Synechocystis sp. PCC 6803 varies in different growth stages, with a peak upon entry into the rapid growth phase, as well as a positive correlation with light intensity. In contrast, a mutant that can no longer synthesize the main carbon storage compound glycogen showed higher energy charge. The overflow of organic acids in this mutant under nitrogen depletion could alsomore » be triggered under high light in nitrogen-replete conditions, with an energy input level dependency. Lastly, these findings suggest that energy charge in cyanobacteria is tightly linked to growth and carbon partition and that energy management is of key significance for their application as photosynthetic carbon dioxide-assimilating cell factories.« less

Glycogen Synthesis and Metabolite Overflow Contribute to Energy Balancing in Cyanobacteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cano, Melissa A.; Holland, Steven C.; Artier, Juliana

Understanding how living cells manage high-energy metabolites such as ATP and NADPH is essential for understanding energy transformations in the biosphere. Using light as the energy input, we find that energy charge (ratio of ATP over ADP+ATP) in the cyanobacterium Synechocystis sp. PCC 6803 varies in different growth stages, with a peak upon entry into the rapid growth phase, as well as a positive correlation with light intensity. In contrast, a mutant that can no longer synthesize the main carbon storage compound glycogen showed higher energy charge. The overflow of organic acids in this mutant under nitrogen depletion could alsomore » be triggered under high light in nitrogen-replete conditions, with an energy input level dependency. Lastly, these findings suggest that energy charge in cyanobacteria is tightly linked to growth and carbon partition and that energy management is of key significance for their application as photosynthetic carbon dioxide-assimilating cell factories.« less

Comparing peracetic acid and hypochlorite for disinfection of combined sewer overflows: Effects of suspended-solids and pH.

PubMed

McFadden, M; Loconsole, J; Schockling, A J; Nerenberg, R; Pavissich, J P

2017-12-01

Peracetic acid (PAA) is an alternative disinfectant that may be effective for combined sewer overflow (CSO) disinfection, but little is known about the effect of particle size on PAA disinfection efficiency. In this work, PAA and hypochlorite were compared as disinfectants, with a focus on the effect of wastewater particles. Inactivation experiments were conducted on suspended cultures of Escherichia coli and wastewater suspended solids. Tested size fractions included particle diameters <10μm, <100μm, and raw wastewater. Chlorine disinfection efficiency decreased with increasing solids size. However, solids size had little effect on PAA disinfection. The PAA disinfection efficiency decreased at pH values above 7.5. Live/dead staining revealed that PAA disinfection leaves most cells in a viable but non-culturable condition. Fourier transform infrared spectroscopy (FTIR) analyses suggests that PAA and hypochlorite may inactivate E. coli bacteria by similar mechanisms. Copyright © 2017 Elsevier B.V. All rights reserved.

Euler technology assessment for preliminary aircraft design employing OVERFLOW code with multiblock structured-grid method

NASA Technical Reports Server (NTRS)

Treiber, David A.; Muilenburg, Dennis A.

1995-01-01

The viability of applying a state-of-the-art Euler code to calculate the aerodynamic forces and moments through maximum lift coefficient for a generic sharp-edge configuration is assessed. The OVERFLOW code, a method employing overset (Chimera) grids, was used to conduct mesh refinement studies, a wind-tunnel wall sensitivity study, and a 22-run computational matrix of flow conditions, including sideslip runs and geometry variations. The subject configuration was a generic wing-body-tail geometry with chined forebody, swept wing leading-edge, and deflected part-span leading-edge flap. The analysis showed that the Euler method is adequate for capturing some of the non-linear aerodynamic effects resulting from leading-edge and forebody vortices produced at high angle-of-attack through C(sub Lmax). Computed forces and moments, as well as surface pressures, match well enough useful preliminary design information to be extracted. Vortex burst effects and vortex interactions with the configuration are also investigated.

Glycogen Synthesis and Metabolite Overflow Contribute to Energy Balancing in Cyanobacteria.

PubMed

Cano, Melissa; Holland, Steven C; Artier, Juliana; Burnap, Rob L; Ghirardi, Maria; Morgan, John A; Yu, Jianping

2018-04-17

Understanding how living cells manage high-energy metabolites such as ATP and NADPH is essential for understanding energy transformations in the biosphere. Using light as the energy input, we find that energy charge (ratio of ATP over ADP+ATP) in the cyanobacterium Synechocystis sp. PCC 6803 varies in different growth stages, with a peak upon entry into the rapid growth phase, as well as a positive correlation with light intensity. In contrast, a mutant that can no longer synthesize the main carbon storage compound glycogen showed higher energy charge. The overflow of organic acids in this mutant under nitrogen depletion could also be triggered under high light in nitrogen-replete conditions, with an energy input level dependency. These findings suggest that energy charge in cyanobacteria is tightly linked to growth and carbon partition and that energy management is of key significance for their application as photosynthetic carbon dioxide-assimilating cell factories. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Assessing the Hydraulic Criticality of Deep Ocean Overflows

NASA Astrophysics Data System (ADS)

Pratt, L. J.; Helfrich, K. R.

2004-12-01

Two methods for assessing the hydraulic criticality of a modelled or observed deep overflow are discussed. The methods should be of use in determining the position of the control section, which is needed to establish the transport relation helpful for long-term monitoring from upstream. Both approaches are based on a multiple streamtube idealization in which the observed flow at a particular section is divided up into subsections (streamtubes). There are no restrictions on the bottom topography or potential vorticity distribution. The first criteria involves evauation of a generalized Jacobian condition based on the conservation laws for each streamtube; the second involves direct calculation of the long-wave phase speeds. We also comment on the significance of the local Froude number F of the flow and argue that F must pass through unity across a section of hydraulic control. These criteria are applied to some numerically modelled flows and are used in the companion presentation (Girton, et al.) to evaluate the hydraulic criticality of the Faroe Bank Channel.

SANITARY-SEWER OVERFLOW CONTROL STRATEGY

EPA Science Inventory

This paper presents a strategy for the abatement of pollution from storm-generated sanitary-sewer overflows (SSO). Because of the great lengths of sanitary-sewer systems and their associated vast number of house-service laterals or building connections, it is often less expensive...

SSOAP Toolbox Enhancements and Case Study

EPA Science Inventory

Recognizing the need for tools to support the development of sanitary sewer overflow (SSO) control plans, in October 2009 the U.S. Environmental Protection Agency (EPA) released the first version of the Sanitary Sewer Overflow Analysis and Planning (SSOAP) Toolbox. This first ve...

Conservative Overset Grids for Overflow For The Sonic Wave Atmospheric Propagation Project

NASA Technical Reports Server (NTRS)

Onufer, Jeff T.; Cummings, Russell M.

1999-01-01

Methods are presented that can be used to make multiple, overset grids communicate in a conservative manner. The methods are developed for use with the Chimera overset method using the PEGSUS code and the OVERFLOW solver.

USEPA CAPSTONE REPORT: CONTROL AND TREATMENT

EPA Science Inventory

Combined-sewer overflows (CSOs), sanitary-sewer overflows and stormwater (SW) are significant contributors of contamination to surface waters. During a rain event, the flow in a combined sewer system may exceed the capacity of the intercepting sewer leading to the wastewater trea...

OVERVIEW OF EPA'S WET-WEATHER FLOW RESEARCH PROGRAM

EPA Science Inventory

Surface waters receive three types of urban wet-weather flow discharges: combined-sewer overflow (CSO), stormwater, and sanitary-sewer overflow (SSO); all are principally untreated discharges that occur during storm-flow events. WWFs have proven to generate a substantial amount o...

41. VIEW FROM END OF FLUME, LOOKING WEST, SHOWING OVERFLOW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. VIEW FROM END OF FLUME, LOOKING WEST, SHOWING OVERFLOW CHUTE ON RIGHT (PARALLEL TO FLUME), RESERVOIR EMBANKMENT IN BACKGROUND, AND HOOKS ON END OF RAILING FOR SPILLBOARDS - Electron Hydroelectric Project, Along Puyallup River, Electron, Pierce County, WA

USING VISUAL PLUMES PREDICTIONS TO MODULATE COMBINED SEWER OVERFLOW (CSO) RATES

EPA Science Inventory

High concentrations of pathogens and toxic residues in creeks and rivers can pose risks to human health and ecological systems. Combined Sewer Overflows (CSOs) discharging into these watercourses often contribute significantly to elevating pollutant concentrations during wet weat...

Notification: Review of Atlanta Combined Sewer Overflow Consent Decree

EPA Pesticide Factsheets

Project #OPE-FY17-0014, March 30, 2017. The EPA OIG plans to begin a review of EPA Region 4’s oversight of the Atlanta combined sewer overflow consent decree. For more information, please click on the link above.

Urban Runoff and Combined Sewer Overflow.

ERIC Educational Resources Information Center

Field, Richard; Gardner, Bradford B.

1978-01-01

Presents a literature review of wastewater treatment, covering publications of 1976-77. This review includes areas such as: (1) urban runoff quality and quantity; (2) urban hydrology; (3) management practices; and (4) combined sewer overflows. A list of 140 references is also presented. (HM)

High-Rate Disinfection Techniques for Combined Sewer Overflow (Proceedings Paper)

EPA Science Inventory

This paper presents high-rate disinfection technologies for combined sewer overflow (CSO). The high-rate disinfection technologies of interest are: chlorination/dechlorination, ultraviolet light irradiation (UV), chlorine dioxide (ClO2 ), ozone (O3), peracetic acid (CH3COOOH ), a...

Stage Separation CFD Tool Development and Evaluation

NASA Technical Reports Server (NTRS)

Droege, Alan; Gomez, Reynaldo; Wang, Ten-See

2002-01-01

This viewgraph presentation evaluates CFD (Computational Fluid Dynamics) tools for solving stage separation problems. The demonstration and validation of the tools is for a second generation RLV (Reusable Launch Vehicle) stage separation. The flow solvers are: Cart3D; Overflow/Overflow-D; Unic.

CONTROL STRATEGY FOR STORM-GENERATED SANITARY-SEWER OVERFLOWS

EPA Science Inventory

This paper presents a strategy for the abatement of pollution from storm-generated sanitary-sewer overflows (SSO). Because of the great lengths of sanitary sewer systems, it is often less expensive to use alterantives to sewerline rehabilitation for infiltration/inflow (I/I) and ...

CONTROL STRATEGY FOR STORM-GENERATED SANITARY-SEWER OVERFLOWS

EPA Science Inventory

This paper presents a strategy for the abatement of pollution from storm-generated sanitary-sewer overflows (SSO). Because of the great lengths of sanitary-sewer systems and their associated vast number of house-service laterals or building connections, it is often less expensiv...

Report: Atlanta Is Largely in Compliance with Its Combined Sewer Overflow Consent Decree, but Has Not Yet Met All Requirements

EPA Pesticide Factsheets

Report #18-P-0206, May 30, 2018. Decreases in sewage overflows from Atlanta's wastewater treatment facilities and sewage transmission pipes reduce the risk of city residents being exposed to pathogens.

Sanitary Sewer Overflow Analysis and Planning (SSOAP) Toolbox

EPA Science Inventory

Rainfall-derived infiltration and inflow (RDII) into sanitary sewer systems has long been recognized as a source of operating problems in sewerage systems. RDII is the main cause of sanitary sewer overflows (SSOs) to basements, streets, or nearby receiving waters and can also ...

Implementation of Finite Rate Chemistry Capability in OVERFLOW

NASA Technical Reports Server (NTRS)

Olsen, M. E.; Venkateswaran, S.; Prabhu, D. K.

2004-01-01

An implementation of both finite rate and equilibrium chemistry have been completed for the OVERFLOW code, a chimera capable, complex geometry flow code widely used to predict transonic flow fields. The implementation builds on the computational efficiency and geometric generality of the solver.

Control Strategy for Storm-Generated Sanitary Sewer Overflows

EPA Science Inventory

This presentation covers a strategy for the abatement of pollution from sanitary-sewer overflows (SSO). Because of the great lengths of sanitary sewer systems, it is often less expensive to use alternatives to sewerline rehabilitation for infiltration/inflow (I/I) and associated ...

SEWER SEDIMENT AND CONTROL: A MANAGEMENT PRACTICES REFERENCES GUIDE

EPA Science Inventory

Sewer-solids sediment is one of major sources of pollutants in urban wet-weather flow (WWF) discharges that include combined-sewer overflow (CSO), separate sanitary-sewer overflow (SSO), and stormwater runoff. During low-flow, dry-weather periods, sanitary wastewater solids depo...

CHALLENGES OF COMBINED SEWER OVERFLOW DISINFECTION BY ULTRAVIOLET LIGHT IRRADIATION

EPA Science Inventory

This article examines the performance and effectiveness of ultraviolet (UV) light irradiation for disinfection of combined sewer overflow (CSO). Due to the negative impact of conventional water disinfectants on aquatic life, new agents (e.g., UV light) are being investigated for ...

EVALUATING INNOVATIVE STORMWATER TREATMENT TECHNOLOGIES UNDER THE ENVIRONMENTAL TECHNOLOGY VERIFICATION (ETV) PROGRAM

EPA Science Inventory

Assessing, controlling, and treating combined-sewer overflows (CSO), sanitary sewer overflows (SSO), and urban stormwater runoff have become priorities for communities. Improved and cost effective treatment technologies are needed to reduce the adverse impacts that wet weather f...

PERFORMANCE OF OZONE AS A DISINFECTANT FOR COMBINED SEWER OVERFLOW

EPA Science Inventory

Disinfection of combined sewer overflow (CSO) minimizes the amount of disease-causing microorganisms (pathogens) released into receiving waters. Currently, the primary disinfecting agent used in the US for wastewater treatment is chlorine (Cl2); however, Cl2 produces problems in ...

Endothelial dysfunction impairs vascular neurotransmission in tail arteries.

PubMed

Sousa, Joana B; Fresco, Paula; Diniz, Carmen

2015-01-01

The present study intends to clarify if endothelium dysfunction impairs vascular sympathetic neurotransmission. Electrically-evoked tritium overflow (100 pulses/5 Hz) was evaluated in arteries (intact and denuded) or exhibiting some degree of endothelium dysfunction (spontaneously hypertensive arteries), pre-incubated with [(3)H]-noradrenaline in the presence of enzymes (nitric oxide synthase (NOS); nicotinamide adenine dinucleotide phosphate (NADPH) oxidase; xanthine oxidase; cyclooxygenase; adenosine kinase) inhibitors and a nucleoside transporter inhibitor. Inhibition of endothelial nitric oxide synthase with L-NIO dihydrochloride reduced tritium overflow in intact arteries whereas inhibition of neuronal nitric oxide synthase with Nω-Propyl-L-arginine hydrochloride was devoid of effect showing that only endothelial nitric oxide synthase is involved in vascular sympathetic neuromodulation. Inhibition of enzymes involved in reactive oxygen species or prostaglandins production with apocynin and allopurinol or indomethacin, respectively, failed to alter tritium overflow. A facilitation or reduction of tritium overflow was observed in the presence of 8-cyclopentyl-1,3-dipropylxanthine (DPCPX) or of 5-iodotubericidin, respectively, but only in intact arteries. These effects can be ascribed to a tonic inhibitory effect mediated by A1 receptors. In denuded and hypertensive arteries, 7-(2-phenylethyl)-5-amino-2-(2-furyl)-pyrazolo-[4,3-e]-1,2,4-triazolo[1,5-c] pyrimidine (SCH 58261) reduced tritium overflow, suggesting the occurrence of a tonic activation of A2A receptors. When endogenous adenosine bioavailability was increased by the nucleoside transporter inhibitor, S-(4-Nitrobenzyl)-6-thioinosine, tritium overflow increased in intact, denuded and hypertensive arteries. Among the endothelium-derived substances studied that could alter vascular sympathetic transmission only adenosine/adenosine receptor mediated mechanisms were clearly impaired by endothelium injury/dysfunction. Copyright © 2014 Elsevier Ltd. All rights reserved.

Very large eddy simulation of the Red Sea overflow

NASA Astrophysics Data System (ADS)

Ilıcak, Mehmet; Özgökmen, Tamay M.; Peters, Hartmut; Baumert, Helmut Z.; Iskandarani, Mohamed

Mixing between overflows and ambient water masses is a critical problem of deep-water mass formation in the downwelling branch of the meridional overturning circulation of the ocean. Modeling approaches that have been tested so far rely either on algebraic parameterizations in hydrostatic ocean circulation models, or on large eddy simulations that resolve most of the mixing using nonhydrostatic models. In this study, we examine the performance of a set of turbulence closures, that have not been tested in comparison to observational data for overflows before. We employ the so-called very large eddy simulation (VLES) technique, which allows the use of k-ɛ models in nonhydrostatic models. This is done by applying a dynamic spatial filtering to the k-ɛ equations. To our knowledge, this is the first time that the VLES approach is adopted for an ocean modeling problem. The performance of k-ɛ and VLES models are evaluated by conducting numerical simulations of the Red Sea overflow and comparing them to observations from the Red Sea Outflow Experiment (REDSOX). The computations are constrained to one of the main channels transporting the overflow, which is narrow enough to permit the use of a two-dimensional (and nonhydrostatic) model. A large set of experiments are conducted using different closure models, Reynolds numbers and spatial resolutions. It is found that, when no turbulence closure is used, the basic structure of the overflow, consisting of a well-mixed bottom layer (BL) and entraining interfacial layer (IL), cannot be reproduced. The k-ɛ model leads to unrealistic thicknesses for both BL and IL, while VLES results in the most realistic reproduction of the REDSOX observations.

ULTRAVIOLET LIGHT DISINFECTION OF COMBINED SEWER OVERFLOW (NEW ORLEANS)

EPA Science Inventory

The objective of this state-of-the-art review is to examine the performance and effectiveness of ultraviolet (UV) light disinfection for combined sewer overflow (CSO) applications. Topics presented include the use of UV light as a disinfecting agent, its practical applications, d...

APPROACH TO "FURTHER-REASONABLE-PROGRESS" TO ATTAIN WATER QUALITY STANDARDS

EPA Science Inventory

Watershed managers in urban areas in the US are pursuing optimum strategies or plans for managing wastewater treatment plants, stormwater systems, sanitary sewer overflows (SSO) and combined sewer overflows (CSO). Often these strategies are based on an iterative process or a "fur...

APPROACH TO "FURTHER-REASONABLE-PROGRESS" TO ATTAIN WATER QUALITY STANDARDS

EPA Science Inventory

Watershed managers in urban areas in the US are pursuing optimum strategies or plans for managing wastewater treatment plants, stormwater systems, sanitary sewer overflows (SSO) and combined sewer overflows (CSO). Often thes strategies are based on an iterative process or a "furt...

Enforcement to Address Sewer Overflows | Eliminating ...

EPA Pesticide Factsheets

2017-04-10

EPA's compliance goal is to eliminate sanitary sewer overflows (SSOs) from municipal collection systems and to ensure that wastewater is being conveyed to treatment plants in accordance with the requirements of the Clean Water Act. To eliminate SSOs, EPA uses a mix of compliance and enforcement tools.

A Riccati model for Denmark Strait overflow variability

NASA Astrophysics Data System (ADS)

Käse, R. H.

2006-10-01

A controlled volume box model of the western basins of the Nordic Seas for water denser than 1027.8 kg m-3 is constructed, where accumulation in volume ($\\frac{dV}{dt) is driven by net imbalances between prescribed net inflow from the northern, eastern and top boundaries (Qs) and hydraulically limited outflow through the Denmark Strait. The resulting Riccati equation is solved analytically for filling and flushing experiments with constant Qs and numerically for stochastic forcing Qs(t). For small perturbations to Qs with white noise spectrum, the overflow response is red noise with a time scale between 5 and 15 years depending on the mean interface height and area. For Qs proportional to the NAO index, the overflow is positively correlated with the NAO. A 140 years integration reveals variations in the overflow between 2.5 Sv in the 1970s and a maximum of 4 Sv in the 1990s. Hydraulic transport calculations from hydrographic data north of Iceland show good agreement with the model hindcast.

Subterranean drilling and in situ treatment of wastes using a contamination control system and methods relating thereto

DOEpatents

Jessmore, James J.; Loomis, Guy G.; Pettet, Mark C.; Flyckt, Melissa C.

2004-09-28

Systems and methods relating to subterranean drilling while maintaining containment of any contaminants released during the drilling. A thrust block installed over a zone of interest provides an overflow space for retaining any contaminants and excess sealant returns. Negative air pressure may be maintained in the overflow space by a ventilation system. Access ports in the thrust block seal the overflow space from the surrounding environment with a membrane seal. A flexible sack seal in the access port may be connected to a drill shroud prior to drilling, providing containment during drilling after the drill bit penetrates the membrane seal. The drill shroud may be adapted to any industry standard drilling rig and includes a connection conduit for connecting to the flexible sack seal and a flexible enclosure surrounding the drill shaft and of a length to accommodate full extension thereof. Upon withdrawal, the sack seal may be closed off and separated, maintaining containment of the overflow space and the drill shroud.

Release inhibitory receptors activation favours the A2A-adenosine receptor-mediated facilitation of noradrenaline release in isolated rat tail artery

PubMed Central

Fresco, Paula; Diniz, Carmen; Queiroz, Glória; Gonçalves, Jorge

2002-01-01

Interactions between A2A-adenosine receptors and α2-, A1- and P2- release-inhibitory receptors, on the modulation of noradrenaline release were studied in isolated rat tail artery. Preparations were labelled with [3H]-noradrenaline, superfused with desipramine-containing medium, and stimulated electrically (100 pulses at 5 Hz or 20 pulses at 50 Hz).Blockade of α2-autoreceptors with yohimbine (1 μM) increased tritium overflow elicited by 100 pulses at 5 Hz but not by 20 pulses at 50 Hz.The selective A2A-receptor agonist 2-p-(2-carboxyethyl)phenethylamino-5′-N-ethylcarboxamidoadenosine (CGS 21680; 1 – 100 nM) enhanced tritium overflow elicited by 100 pulses at 5 Hz. Yohimbine prevented the effect of CGS 21680, which was restored by the A1-receptor agonist N6-cyclopentyladenosine (CPA; 100 nM) or by the P2-receptor agonist 2-methylthioadenosine triphosphate (2-MeSATP; 80 μM).CGS 21680 (100 nM) failed to increase tritium overflow elicited by 20 pulses at 50 Hz. The α2-adrenoceptor agonist 5-bromo-6-(2-imidazolin-2-ylamino)-quinoxaline (UK 14304; 30 nM), the A1-receptor agonist CPA (100 nM) or the P2-receptor agonist 2-MeSATP (80 μM) reduced tritium overflow. In the presence of these agonists CGS 21680 elicited a facilitation of tritium overflow.Blockade of potassium channels with tetraethylammonium (TEA; 5 mM) increased tritium overflow elicited by 100 pulses at 5 Hz to values similar to those obtained in the presence of yohimbine but did not prevent the effect of CGS 21680 (100 nM) on tritium overflow.It is concluded that, in isolated rat tail artery, the facilitation of noradrenaline release mediated by A2A-adenosine receptors is favoured by activation of release inhibitory receptors. PMID:12010771

Soil infiltration characteristics in the Tarim River floodplain

USDA-ARS?s Scientific Manuscript database

Overflow from rivers play an important role for ecological conservation in Tarim Basin, however, there was limited information on infiltration from overflow of the Tarim River. The objective of this study was to investigate steady infiltration rate for three types of land use (forest, shrub and bare...

DEVELOPMENT OF SANITARY SEWER OVERFLOW ANALYSIS AND PLANNING (SSOAP) TOOLBOX

EPA Science Inventory

Rainfall Derived Infiltration and Inflow (RDII) into sanitary sewer systems has long been recognized as a source of operating problems in sewerage systems. RDII is the main cause of sanitary sewer overflows (SSOs) to basements, streets, or nearby streams. RDII can also cause se...

SSOAP - A TOOLBOX FOR SANITARY SEWER OVERFLOW ANALYSIS AND PLANNING

EPA Science Inventory

Rainfall Derived Infiltration and Inflow (RDII) into sanitary sewer systems has long been recognized as a source of operating problems in sewerage systems. RDII is the main cause of sanitary sewer overflows (SSOs) to basements, streets, or nearby streams and can also cause serio...

SSOAP - A TOOLBOX FOR SANITARY SEWER OVERFLOW ANALYSIS AND PLANNING

EPA Science Inventory

Rainfall Derived Infiltration and Inflow (RDII) into sanitary sewer systems has long been recognized as a source of operating problems in sewerage systems. RDII is the main cause of sanitary sewer overflows (SSOs) to basements, streets, or nearby streams and can also cause seriou...

Drag Prediction for the DLR-F4 Wing/Body using OVERFLOW and CFL3D on an Overset Mesh

NASA Technical Reports Server (NTRS)

Vassberg, John C.; Buning, Pieter G.; Rumsey, Christopher L.

2002-01-01

This paper reviews the importance of numerical drag prediction in an aircraft design environment. A chronicle of collaborations between the authors and colleagues is discussed. This retrospective provides a road-map which illustrates some of the actions taken in the past seven years in pursuit of accurate drag prediction. The advances made possible through these collaborations have changed the manner in which business is conducted during the design of all-new aircraft. The subject of this study is the DLR-F4 wing/body transonic model. Specifically, the work conducted herein was in support of the 1st CFD Drag Prediction Workshop, which was held in conjunction with the 19th Applied Aerodynamics Conference in Anaheim, CA during June, 2001. Comprehensive sets of OVERFLOW simulations were independently performed by several users on a variety of computational platforms. CFL3D was used on a limited basis for additional comparison on the same overset mesh. Drag polars based on this database were constructed with a CFD-to-Test correction applied and compared with test data from three facilities. These comparisons show that the predicted drag polars fall inside the scatter band of the test data, at least for pre-buffet conditions. This places the corrected drag levels within 1% of the averaged experimental values. At the design point, the OVERFLOW and CFL3D drag predictions are within 1-2% of each other. In addition, drag-rise characteristics and a boundary of drag-divergence Mach number are presented.

40 CFR 35.2024 - Combined sewer overflows.

Code of Federal Regulations, 2010 CFR

2010-07-01

... project priority list, it addresses impaired uses in priority water quality areas which are due to the... must demonstrate to the Administrator that the water quality goals of the Act will not be achieved... priority water quality areas in marine bays and estuaries due to the impacts of combined sewer overflows...

76 FR 16722 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-25

..., Overflow Creek Tributary, Red Cut Slough, Red Cut Slough Tributary, Red Cut Slough Tributary 2, and Red Cut... flooding sources: Gum Creek Flooding Effects, Little Red River, Overflow Creek Tributary, Red Cut Slough, Red Cut Slough Tributary, Red Cut Slough Tributary 2, and Red Cut Slough Tributary A. In this notice...

COMPUTER MODEL ANALYSIS FOR MITIGATION PLANNING OF SANITARY-SEWER OVERFLOWS

EPA Science Inventory

Sanitary sewer overflows (SSOs) are generally difficult to witness or document as they usually occur during rain events when people are indoors or out of sight. To anser where and when an SSO may occur, it is necessary to know the flow conveyance capacity at various parts of the ...

A TOOLBOX FOR SANITARY SEWER OVERFLOW ANALYSIS AND PLANNING (SSOAP) AND APPLICATIONS

EPA Science Inventory

Rainfall Derived Infiltration and Inflow (RDII) into sanitary sewer systems has long been recognized as a source of operating problems in sewerage systems. RDII is the main cause of sanitary sewer overflows (SSOs) to basements, streets, or nearby streams and can also cause seriou...

21. Overflow pipe in filtration bed. Located at each corner ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. Overflow pipe in filtration bed. Located at each corner of the bed, the pipes drain off any excess water and maintain a limit on water depth. - Lake Whitney Water Filtration Plant, Filtration Plant, South side of Armory Street between Edgehill Road & Whitney Avenue, Hamden, New Haven County, CT

Demonstration of Green/Gray Infrastructure for Combined Sewer Overflow Control

EPA Science Inventory

This project is a major national demonstration of the integration of green and gray infrastructure for combined sewer overflow (CSO) control in a cost-effective and environmentally friendly manner. It will use Kansas City, MO, as a case example. The project will have a major in...

Sanitary Sewer Overflows and Association with Gastrointestinal Illness: A case crossover analysis of Massachusetts Data, 2006-2007

EPA Science Inventory

Sanitary sewer overflows (SSOs) occur when untreated sewage is discharged into water sources potentially causing contamination. SSOs are primarily caused by heavy rainfall, which is expected to become heavier and more episodic due to climate change. We conducted a case-crossover ...

Water quality in the Mahoning River and selected tributaries in Youngstown, Ohio

USGS Publications Warehouse

Stoeckel, Donald M.; Covert, S. Alex

2002-01-01

The lower reaches of the Mahoning River in Youngstown, Ohio, have been characterized by the Ohio Environmental Protection Agency (OEPA) as historically having poor water quality. Most wastewater-treatment plants (WWTPs) in the watershed did not provide secondary sewage treatment until the late 1980s. By the late 1990s, the Mahoning River still received sewer-overflow discharges from 101 locations within the city of Youngstown, Ohio. The Mahoning River in Youngstown and Mill Creek, a principal tributary to the Mahoning River in Youngstown, have not met biotic index criteria since the earliest published assessment by OEPA in 1980. Youngstown and the OEPA are working together toward the goal of meeting water-quality standards in the Mahoning River. The U.S. Geological Survey collected information to help both parties assess water quality in the area of Youngstown and to estimate bacteria and inorganic nitrogen contributions from sewer-overflow discharges to the Mahoning River. Two monitoring networks were established in the lower Mahoning River: the first to evaluate hydrology and microbiological and chemical water quality and the second to assess indices of fish and aquatic-macroinvertebrate-community health. Water samples and water-quality data were collected from May through October 1999 and 2000 to evaluate where, when, and for how long water quality was affected by sewer-overflow discharges. Water samples were collected during dry- and wet-weather flow, and biotic indices were assessed during the first year (1999). The second year of sample collection (2000) was directed toward evaluating changes in water quality during wet-weather flow, and specifically toward assessing the effect of sewer-overflow discharges on water quality in the monitoring network. Water-quality standards for Escherichia coli (E. coli) concentration and draft criteria for nitrate plus nitrite and total phosphorus were the regulations most commonly exceeded in the Mahoning River and Mill Creek sampling networks. E. coli concentrations increased during wet-weather flow and remained higher than dry-weather concentrations for 48 hours after peak flow. E. coli concentration criteria were more commonly exceeded during wet-weather flow than during dry-weather flow. Exceedances of nutrient-concentration criteria were not substantially more common during wet-weather flow. The fish and aquatic macroinvertebrate network included Mill Creek and its tributaries but did not include the main stem of the Mahoning River. Persistent exceedances of chemical water-quality standards in Mill Creek and the presence of nutrient concentrations in excess of draft criteria may have contributed to biotic index scores that on only one occasion met State criteria throughout the fish and aquatic macroinvertebrate sampling network. Monitored tributary streams did not contribute concentrations of E. coli, nitrate plus nitrite, or total phosphorus to the Mahoning River and Mill Creek that were higher than main-stem concentrations, but monitored WWTP and sewer-overflow discharges did contribute. Twenty-four hour load estimates of sewer-overflow discharge contributions during wet-weather flow indicated that sewer-overflow discharges contributed large loads of bacteria and inorganic nitrogen to the Mahoning River relative to the instream load. The sewer-overflow loads appeared to move as a slug of highly enriched water that passed through Youngstown on the rising limb of the storm hydrograph. The median estimated sewer-overflow load contribution of bacteria was greater than the estimated instream load by a factor of five or more; however, the median estimated sewer-overflow load of inorganic nitrogen was less than half of the estimated instream load. Sewer-overflow discharges contributed loads of E. coli and nutrients to the Mahoning River and Mill Creek at a point where the streams already did not meet State water-quality regulations. Improvement of water quality of

Clostridium thermocellum DSM 1313 transcriptional responses to redox perturbation

DOE PAGES

Sander, Kyle B.; Wilson, Charlotte M.; M. Rodriquez, Jr.; ...

2015-12-12

Clostridium thermocellum is a promising consolidated bioprocessing candidate organism capable of directly converting lignocellulosic biomass to ethanol. Current ethanol yields, productivities, and growth inhibitions are industrial deployment impediments for commodity fuel production by this bacterium. Redox imbalance under certain conditions and in engineered strains may contribute to incomplete substrate utilization and may direct fermentation products to undesirable overflow metabolites. As a result, towards a better understanding of redox metabolism in C. thermocellum, we established continuous growth conditions and analyzed global gene expression during addition of two stress chemicals (methyl viologen and hydrogen peroxide) which changed the fermentation redox potential.

Near-Body Grid Adaption for Overset Grids

NASA Technical Reports Server (NTRS)

Buning, Pieter G.; Pulliam, Thomas H.

2016-01-01

A solution adaption capability for curvilinear near-body grids has been implemented in the OVERFLOW overset grid computational fluid dynamics code. The approach follows closely that used for the Cartesian off-body grids, but inserts refined grids in the computational space of original near-body grids. Refined curvilinear grids are generated using parametric cubic interpolation, with one-sided biasing based on curvature and stretching ratio of the original grid. Sensor functions, grid marking, and solution interpolation tasks are implemented in the same fashion as for off-body grids. A goal-oriented procedure, based on largest error first, is included for controlling growth rate and maximum size of the adapted grid system. The adaption process is almost entirely parallelized using MPI, resulting in a capability suitable for viscous, moving body simulations. Two- and three-dimensional examples are presented.

--No Title--

Science.gov Websites

{margin:0;padding:0;border:0;outline:0;line-height:1.3;text-decoration:none;font-size:100%;list-style:none -state-disabled{cursor:default!important}.ui-icon{display:block;text-indent:-99999px;overflow:hidden -align:middle;text-align:center;overflow:visible}.ui-button,.ui-button:link,.ui-button:visited,.ui-button:hover

THE CHOICE OF REAL-TIME CONTROL STRATEGY FOR COMBINED SEWER OVERFLOW CONTROL

EPA Science Inventory

This paper focuses on the strategies used to operate a collection system in real-time control (RTC) in order to optimize use of system capacity and to reduce the cost of long-term combined sewer overflow (CSO) control. Three RTC strategies were developed and analyzed based on the...

Interim Significant Noncompliance Policy for Clean Water Act Violations Associated with CSOs, SSOs, CAFOs, and Storm Water Point Sources

EPA Pesticide Factsheets

This policy addresses significant noncompliance (SNC) violations associated with combined sewer overflows (CSOs), sanitary sewer overflows (SSOs), concentrated animal feeding operations (CAFOs), and storm water point source discharges covered by the National Pollutant Discharge Elimination System (NPDES) program under the Clean Water Act (CWA).

A Closer Look at Motor Overflow in Dyslexic Children.

ERIC Educational Resources Information Center

Parlow, S. E.

Unintentional movement "overflow" between the hands or "mirror movements" are common in young children, but are generally regarded as indicative of developmental delay in older children. This study was designed to investigate mirror movements in a sample of 23 very poor readers, ages 11-13, with learning disabilities, and in a…

Soil characteristics of the vadose zone in the flood plain of the Tarim River

USDA-ARS?s Scientific Manuscript database

Overflow from rivers plays an important role in ecological conservation. The desert-oasis ecotone in the Tarim River Basin of Northwest China, for example, relies upon overflow from the river to support a diversity of soil, vegetation, and wildlife. There is, however, limited information on soil tex...

7. SAND FILTERS, CANAL TO LEFT. CONCRETE OVERFLOW AREA TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. SAND FILTERS, CANAL TO LEFT. CONCRETE OVERFLOW AREA TO LEFT OF CANAL ORIGINALLY PLANNED AS A STORAGE LAKE. VIEW LOOKING DUE WEST OF HINDS COMPLEX IN BACKGROUND OF SAND FILTERS. - Hinds Pump Plant, East of Joshua Tree National Monument, 5 miles north of Route 10, Hayfield, Riverside County, CA

75 FR 32205 - Felsenthal National Wildlife Refuge, Ashley, Bradley, and Union Counties, AR; Overflow National...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R4-R-2010-N061; 40136-1265-0000-S3] Felsenthal National Wildlife Refuge, Ashley, Bradley, and Union Counties, AR; Overflow National Wildlife Refuge, Ashley County, AR AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of availability...

HIGH-RATE DISINFECTION OF COMBINED SEWER OVERFLOW USING CHLORINE DIOXIDE

EPA Science Inventory

This presentation is a state-of-the-art review of chlorine dioxide (ClO2) used for high-rate disinfection of combined sewer overflow (CSO). The review includes bench-, pilot-, and fullscale studies on the use of ClO2 as a disinfecting agent for a variety of wastewaters. Specific ...

The Mediterranean Overflow in the Gulf of Cadiz: A rugged journey

PubMed Central

Sánchez-Leal, Ricardo F.; Bellanco, María Jesús; Fernández-Salas, Luis Miguel; García-Lafuente, Jesús; Gasser-Rubinat, Marc; González-Pola, César; Hernández-Molina, Francisco J.; Pelegrí, Josep L.; Peliz, Alvaro; Relvas, Paulo; Roque, David; Ruiz-Villarreal, Manuel; Sammartino, Simone; Sánchez-Garrido, José Carlos

2017-01-01

The pathways and transformations of dense water overflows, which depend on small-scale interactions between flow dynamics and erosional-depositional processes, are a central piece in the ocean’s large-scale circulation. A novel, high-resolution current and hydrographic data set highlights the intricate pathway travelled by the saline Mediterranean Overflow as it enters the Atlantic. Interaction with the topography constraints its spreading. Over the initial 200 km west of the Gibraltar gateway, distinct channels separate the initial gravity current into several plunging branches depth-sorted by density. Shallow branches follow the upper slope and eventually detach as buoyant plumes. Deeper branches occupy mid slope channels and coalesce upon reaching a diapiric ridge. A still deeper branch, guided by a lower channel wall marked by transverse furrows, experiences small-scale overflows which travel downslope to settle at mid-depths. The Mediterranean salt flux into the Atlantic has implications for the buoyancy balance in the North Atlantic. Observations on how this flux enters at different depth levels are key to accurately measuring and understanding the role of Mediterranean Outflow in future climate scenarios. PMID:29152570

Atlantic Water transformation in the Nordic Seas and its influence on the export rate of the Overflow Waters

NASA Astrophysics Data System (ADS)

Garcia Quintana, Yarisbel; Wiesner, Pia; Hu, Xianmin; Myers, Paul

2017-04-01

The Nordic Seas (NS) are the main gateway between the Arctic and the Atlantic Oceans. The basin can be considered as the headwaters for the Meridional Overturning Circulation (MOC), for it is there that the Denmark Strait Overflow Water (DSOW) and the Iceland-Scotland Overflow Water (ISOW) acquire their properties. Their inflow into the North Atlantic Ocean occurs across the Greenland-Scotland ridge. Together with Labrador Sea Water, DSOW and ISOW are the main components of the North Atlantic Deep Water (NADW), which ventilates the lower limb of the Atlantic MOC. In spite recent studies exploring the export rate and later pathways of the overflows, the question about what drives them, remains. Here we explore the transformation of the Atlantic Water (AW) as it enters the NS through Denmark Strait, Iceland Faroe Ridge and Faroe Schotland Channel, as well as its pathways within the basin. To do so, we use an eddy-permitting ocean general circulation model run over the period 2002 to 2015. Two different approaches are used to track the AW transformation in the NS: the well-tested off-line Lagrangian tool ARIANE and on-line passive tracers. In both cases we use the same definition of AW to tag its inflow through the three entering sections. The overflows directly impact circulation and water properties in much of the deep Atlantic Ocean, thus a better understanding of the physical processes behind their variability is crucial a asset.

Occurrence of enrofloxacin in overflows from animal lot and residential sewage lagoons and a receiving-stream.

PubMed

Ikem, Abua; Lin, Chung-Ho; Broz, Bob; Kerley, Monty; Thi, Ho Le

2017-10-01

Enrofloxacin (ENRO), a fluoroquinolone, was quantified in overflows from an animal lot and residential sewage lagoons and in a receiving-stream (Gans Creek). The concentrations of ENRO in samples was determined by high-performance liquid chromatography - tandem mass spectrometry. In total, ninety samples including duplicates were analyzed during several monthly sampling campaigns. The samples collected represented the residential sewage lagoon overflow (RLO), animal lot lagoon overflow (ALLO), the combined overflows (RLO and ALLO), and Gans Creek (upstream, midstream and downstream positions). The frequency of detection of ENRO was 90% for RLO and 100% for both ALLO and Gans Creek. The highest concentration of ENRO (0.44 μg/L) was found in ALLO sample collected during high precipitation. ENRO levels found in RLO samples ranged from < LOQ to 259 ng/L and the highest value observed also coincided with high flow. The levels of ENRO found in Gans Creek ranged from 17-216 ng/L. A preliminary ecotoxicological assessment was conducted through calculation of the risk quotients (RQs) for organisms based on the ratio of the measured environmental concentrations in this study to the predicted-no-effect-concentrations (acute and chronic effect) data. From the RQs, high risks were observed for Microcystis aeruginosa (cyanobacteria; RQ = 4.4); Anabaena flosaquae (cyanobacteria; RQ = 1.3); and Lemna minor (aquatic vascular plant; RQ = 2.0). The long-term effects of mixtures of PHCs on Gans Creek watershed are probable.

Increased release of norepinephrine and dopamine from canine kidney during bilateral carotid occlusion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley, T.; Hjemdahl, P.; DiBona, G.F.

1987-02-01

The renal overflow of norepinephrine (NE) and dopamine (DA) to plasma from the innervated kidney was studied at rest and during sympathetic nervous system activation by bilateral carotid artery occlusion (BCO) in vagotomized dogs under barbiturate or barbiturate/nitrous oxide anesthesia. BCO elevated arterial pressure and the arterial plasma concentration of NE, DA, and epinephrine (Epi). Renal vascular resistance (renal arterial pressure kept constant) increased by 15 +/- 7% and the net renal venous outflows (renal veno-arterial concentration difference x renal plasma flow) of NE and DA were enhanced. To obtain more correct estimates of the renal contribution to the renalmore » venous catecholamine outflow, they corrected for the renal extraction of arterial catecholamines, assessed as the extractions of (/sup 3/H)NE, (/sup 3/H)DA, or endogenous Epi. The (/sup 3/H)NE corrected renal NE overflow to plasma increased from 144 +/- 40 to 243 +/- 64 pmol-min/sup -1/ during BCO, which, when compared with a previous study of the (/sup 3/H)NE corrected renal NE overflow to plasma evoked by electrical renal nerve stimulation, corresponds to a 40% increase in nerve impulse frequency from approx. 0.6 Hz. If the renal catecholamine extraction was not taken into account the effect of BCO was underestimated. The renal DA overflow to plasma was about one-fifth of the NE overflow both at rest and during BCO, indicating that there was no preferential activation of noradrenergic or putative dopaminergic nerves by BCO.« less

Toxicity and pollutant impact analysis in an urban river due to combined sewer overflows loads.

PubMed

Casadio, A; Maglionico, M; Bolognesi, A; Artina, S

2010-01-01

The Navile Channel (Bologna, Italy) is an ancient artificial water course derived from the Reno river. It is the main receiving water body for the urban catchment of Bologna sewer systems and also for the Waste Water Treatment Plant (WWTP) main outlet. The aim of this work is to evaluate the Combined Sewer Overflows (CSOs) impact on Navile Channel's water quality. In order to collect Navile flow and water quality data in both dry and wet weather conditions, two measuring and sampling stations were installed, right upstream and downstream the WWTP outflow. The study shows that even in case of low intensity rain events, CSOs have a significant effect on both water quantity and quality, spilling a considerable amount of pollutants into the Navile Channel and presenting also acute toxicity effects. The collected data shown a good correlations between the concentrations of TSS and of chemical compounds analyzed, suggesting that the most part of such substances is attached to suspended solids. Resulting toxicity values are fairly high in both measuring points and seem to confirm synergistic interactions between heavy metals.

Mechanisms of flow and water mass variability in Denmark Strait

NASA Astrophysics Data System (ADS)

Moritz, Martin; Jochumsen, Kerstin; Quadfasel, Detlef; Mashayekh Poul, Hossein; Käse, Rolf H.

2017-04-01

The dense water export through Denmark Strait contributes significantly to the lower limb of the Atlantic Meridional Overturning Circulation. Overflow water is transported southwestward not only in the deep channel of the Strait, but also within a thin bottom layer on the Greenland shelf. The flow on the shelf is mainly weak and barotropic, exhibiting many recirculations, but may eventually contribute to the overflow layer in the Irminger Basin by spilling events in the northern Irminger Basin. Especially the circulation around Dohrn Bank and the Kangerdlussuaq Trough contribute to the shelf-basin exchange. Moored observations show the overflow in Denmark Strait to be stable during the last 20 years (1996-2016). Nevertheless, flow variability was noticed on time scales of eddies and beyond, i.e. on weekly and interannual scales. Here, we use a combination of mooring data and shipboard hydrographic and current data to address the dominant modes of variability in the overflow, which are (i) eddies, (ii) barotropic pulsations of the plume, (iii) lateral shifts of the plume core position, and (iv) variations in vertical extension, i.e. varying overflow thickness. A principle component analysis is carried out and related to variations in sea surface height and wind stress, derived from satellite measurements. Furthermore, a test for topographic waves is performed. Shelf contributions to the overflow core in the Irminger Basin are identified from measurements of temperature and salinity, as well as velocity, which were obtained during recent cruises in the region. The flow and water mass pattern obtained from the observational data is compared to simulations in a high resolution regional model (ROMS), where tracer release experiments and float deployments were carried out. The modelling results allow a separation between different atmospheric forcing modes (NAO+ vs NAO- situations), which impact the water mass distribution and alter the dense water pathways on the Greenland shelf. Finally, the results are discussed with respect to other regional model studies on the circulation in the northern Irminger Basin.

Removal of nutrients from combined sewer overflows and lake water in a vertical-flow constructed wetland system.

PubMed

Gervin, L; Brix, H

2001-01-01

Lake Utterslev is situated in a densely built-up area of Copenhagen, and is heavily eutrophicated from combined sewer overflows. At the same time the lake suffers from lack of water. Therefore, a 5,000 m2 vertical flow wetland system was constructed in 1998 to reduce the phosphorus discharge from combined sewer overflows without reducing the water supply to the lake. During dry periods the constructed wetland is used to remove phosphorus from the lake water. The system is designed as a 90 m diameter circular bed with a bed depth of c. 2 m. The system is isolated from the surroundings by a polyethylene membrane. The bed medium consists of a mixture of gravel and crushed marble, which has a high binding capacity for phosphorus. The bed is located within the natural littoral zone of the lake and is planted with common reed (Phragmites australis). The constructed wetland is intermittently loaded with combined sewer overflow water or lake water and, after percolation through the bed medium, the water is collected in a network of drainage pipes at the bottom of the bed and pumped to the lake. The fully automated loading cycle results in alternating wet and dry periods. During the initial two years of operation, the phosphorus removal for combined sewer overflows has been consistently high (94-99% of inflow concentrations). When loaded with lake water, the phosphorus removal has been high during summer (71-97%) and lower during winter (53-75%) partly because of lower inlet concentrations. Effluent phosphorus concentrations are consistently low (0.03-0.04 mg/L). Ammonium nitrogen is nitrified in the constructed wetland, and total suspended solids and COD are generally reduced to concentrations below 5 mg/L and 25 mg/L, respectively. The study documents that a subsurface flow constructed wetland system can be designed and operated to effectively remove phosphorus and other pollutants from combined sewer overflows and eutrophicated lake water.

Improved Polyurethane Storage Tank Performance

DTIC Science & Technology

2014-06-30

condition occurred if water overflowed from the tank vent prior to reaching 45 gallons. A spline curve was drawn around the perimeter of each image so...estimated footprint and height envelope was added for spatial reference. A spline color code key was developed, so that the progression of the tanks...Table 4.5.3). A standard flat plate platen was used for the double butt seams and some closing seams by one fabricator. The other utilized a “Slinky

National Waterways Study. Waterway Science and Technology.

DTIC Science & Technology

1981-08-01

Revetments 278 VII-A Split Hull Type Trailing Suction Hopper Dredge 304 VII-B Drag Heads 306 VII-C Overflow Systems 307 VII-D Trailing Suction Hopper... head reversals are possible. Poor approach conditions currently exist at some locks which could have been mitigated if modern, improved design...of ti,.c that a navigable pass section can be used. Navigation dams must be designed to pass high flows and floods with minor swell head and without in

Sympathomimetic effects of MIBG: comparison with tyramine.

PubMed

Graefe, K H; Bossle, F; Wölfel, R; Burger, A; Souladaki, M; Bier, D; Dutschka, K; Farahati, J; Bönisch, H

1999-08-01

Because nothing is known about whether metaiodobenzylguanidine (MIBG) has tyramine-like actions, the sympathomimetic effects of MIBG were determined in the isolated rabbit heart and compared with those of tyramine. Spontaneously beating rabbit hearts were perfused with Tyrode's solution (Langendorff technique; 37 degrees C; 26 mL/min), and the heart rate as well as the norepinephrine and dopamine overflow into the perfusate was measured before and after doses of MIBG or tyramine (0.03-10 micromol) given as bolus injections (100 microL) into the aortic cannula. Km and Vmax values for the neuronal uptake (uptake1) of 125I-MIBG and 14C-tyramine were obtained in human neuroblastoma (SK-N-SH) cells. The Ki of MIBG for inhibition of the 3H-catecholamine uptake mediated by the vesicular monoamine transporter was determined in membrane vesicles obtained from bovine chromaffin granules and compared with the previously reported Ki value for tyramine determined under identical experimental conditions. By producing increases in heart rate and norepinephrine overflow, both compounds had dose-dependent sympathomimetic effects in the rabbit heart. MIBG was much less effective than tyramine in increasing heart rate (maximum effect 59 versus 156 beats/min) and norepinephrine overflow (maximum effect 35 versus 218 pmol/g). Tyramine also caused increases in dopamine overflow, whereas MIBG was a poor dopamine releaser. At a dose of 10 micromol, the increase in heart rate lasted more than 60 min after MIBG and about 20 min after tyramine injection. Accordingly, the norepinephrine overflow caused by 10 micromol MIBG and tyramine declined with half-lives of 57.8 and 2.2 min, respectively. The effects of both drugs were drastically reduced in hearts exposed to 2 micromol/L desipramine. The kinetic parameters characterizing the saturation of neuronal uptake by 125I-MIBG and 14C-tyramine were similar for the two compounds: Km values of MIBG and tyramine were 1.6 and 1.7 micromol/L, respectively, and Vmax values of MIBG and tyramine were 43 and 37 pmol/mg protein/min, respectively. However, in inhibiting the vesicular 3H-catecholamine uptake, MIBG was eight times less potent than tyramine. MIBG is much less effective than tyramine as an indirect sympathomimetic agent. This is probably a result of its relatively low affinity for the vesicular monoamine transporter and explains the relatively poor ability of the drug to mobilize norepinephrine stored in synaptic vesicles. The long duration of MIBG action results primarily from the drug not being metabolized by monoamine oxidase. The sympathomimetic effects of MIBG described here are not likely to come into play in patients given diagnostic or common therapeutic doses of radioiodinated MIBG.

Prospective Science Teachers' Subject-Matter Knowledge about Overflow Container

ERIC Educational Resources Information Center

Ültay, Eser

2016-01-01

The purpose of this study was to determine prospective science teachers' subject-matter knowledge (SMK) about overflow container. This study was carried out in the form of a case study in spring term of the academic year of 2013-2014 with seven sophomore prospective science teachers who were studying at Elementary Science Teaching Department in…

The Importance of Lake Overflow Floods for Early Martian Landscape Evolution: Insights From Licus Vallis

NASA Technical Reports Server (NTRS)

Goudge, T. A.; Fassett, C. I.

2017-01-01

Open-basin lake outlet valleys are incised when water breaches the basin-confining topography and overflows. Outlet valleys record this flooding event and provide insight into how the lake and surrounding terrain evolved over time. Here we present a study of the paleolake outlet Licus Vallis, a >350 km long, >2 km wide, >100 m deep valley that heads at the outlet breach of an approx.30 km diameter impact crater. Multiple geomorphic features of this valley system suggest it records a more complex evolution than formation from a single lake overflow flood. This provides unique insight into the paleohydrology of lakes on early Mars, as we can make inferences beyond the most recent phase of activity..

OVERFLOW-Interaction with Industry

NASA Technical Reports Server (NTRS)

Buning, Pieter G.; George, Michael W. (Technical Monitor)

1996-01-01

A Navier-Stokes flow solver, OVERFLOW, has been developed by researchers at NASA Ames Research Center to use overset (Chimera) grids to simulate the flow about complex aerodynamic shapes. Primary customers of the OVERFLOW flow solver and related software include McDonnell Douglas and Boeing, as well as the NASA Focused Programs for Advanced Subsonic Technology (AST) and High Speed Research (HSR). Code development has focused on customer issues, including improving code performance, ability to run on workstation clusters and the NAS SP2, and direct interaction with industry on accuracy assessment and validation. Significant interaction with NAS has produced a capability tailored to the Ames computing environment, and code contributions have come from a wide range of sources, both within and outside Ames.

Contributions of combined sewer overflows and treated effluents to the bacterial load released into a coastal area.

PubMed

Al Aukidy, M; Verlicchi, P

2017-12-31

The impact of combined sewer overflow (CSO) on the receiving water body is an issue of increasing concern, as it may lead to restrictions in the use and destination of the receiving body, such as bathing or recreational area closures, fish and shellfish consumption restrictions, and contamination of drinking water resources. Recent investigations have mainly referred to the occurrence and loads of suspended solids, organic compounds and, in some cases, micropollutants. Attempts have been made to find correlations between the discharged load and the size and characteristics of the catchment area, climate conditions, rainfall duration and intensity. This study refers to a touristic coastal area in the north-east of Italy, which is characterized by a combined sewer network including 5 CSO outfalls which, in the case of heavy rain events, directly discharge the exceeding water flow rate into channels which, after a short distance, reach the Adriatic Sea. The study analyzed: i) rainfall events during the summer period in 2014 which led to overflow in the different outfalls, ii) the inter- and intra-event variability with regard to E. coli, Enterococci and conductivity, and iii) the hydraulic and pollutant (E. coli and Enterococci) loads discharged by the local wastewater treatment plant and by all the CSO outfalls. Finally, it estimated the contribution of each source to the released hydraulic and pollutant loads into the receiving water body. Moreover, it was also found that the modest water volume discharged by all CSO outfalls (only 8% of the total volume discharged by the area) contains >90% of the microbial load. Copyright © 2017 Elsevier B.V. All rights reserved.

Modification of deep waters in Marguerite Bay, western Antarctic Peninsula, caused by topographic overflows

NASA Astrophysics Data System (ADS)

Venables, Hugh J.; Meredith, Michael P.; Brearley, J. Alexander

2017-05-01

Circumpolar Deep Water (CDW) intrudes from the mid-layers of the Antarctic Circumpolar Current onto the shelf of the western Antarctic Peninsula, providing a source of heat and nutrients to the regional ocean. It is well known that CDW is modified as it flows across the shelf, but the mechanisms responsible for this are not fully known. Here, data from underwater gliders with high spatial resolution are used to demonstrate the importance of detailed bathymetry in inducing multiple local mixing events. Clear evidence for overflows is observed in the glider data as water flows along a deep channel with multiple transverse ridges. The ridges block the densest waters, with overflowing water descending several hundred metres to fill subsequent basins. This vertical flow leads to entrainment of overlying colder and fresher water in localised mixing events. Initially this process leads to an increase in bottom temperatures due to the temperature maximum waters descending to greater depths. After several ridges, however, the mixing is sufficient to remove the temperature maximum completely and the entrainment of colder thermocline waters to depth reduces the bottom temperature, to approximately the same as in the source region of Marguerite Trough. Similarly, it is shown that deep waters of Palmer Deep are warmer than at the same depth at the shelf break. The exact details of the transformations observed are heavily dependent on the local bathymetry and water column structure, but glacially-carved troughs and shallow sills are a common feature of the bathymetry of polar shelves, and these types of processes may be a factor in determining the hydrographic conditions close to the coast across a wider area.

Balancing extensive ambition and a context overflowing with opportunities and demands: A grounded theory on stress and recovery among highly educated working young women entering male-dominated occupational areas

PubMed Central

Löve, Jesper; Hagberg, Mats; Dellve, Lotta

2011-01-01

Several factors underline the issue of stress-related health among young highly educated women. Major societal changes might provide more new challenges with considerably changed and expanded roles than were expected by earlier generations, especially among women. The quantity of young women with higher education has also increased threefold in Sweden in less than two decades and there are a growing number of young women that hereby break with traditional gender positions and enter new occupational areas traditionally dominated by men. The research questions in the present study were: “What is the main concern, regarding stress and recovery, among young highly educated working women breaking with traditional gender positions and entering male-dominated occupational areas?” and “How do they handle this concern?” We conducted open-ended interviews with 20 informants, aged 23-29 years. The results showed that the synergy between highly ambitious individuals and a context overflowing with opportunities and demands ended up in the informants’ constantly striving to find a balance in daily life (main concern). This concern refers to the respondents experiencing a constant overload of ambiguity and that they easily became entangled in a loop of stress and dysfunctional coping behavior, threatening the balance between stress and sufficient recovery. In order to handle this concern, the respondents used different strategies in balancing extensive ambition and a context overflowing with opportunities and demands (core category). This preliminary theoretical model deepens our understanding of how the increasing numbers of highly educated young women face complex living conditions endangering their possibility of maintaining health and work ability. PMID:21909337

Alternative Path Communication in Wide-Scale Cluster-Tree Wireless Sensor Networks Using Inactive Periods

PubMed Central

Leão, Erico; Montez, Carlos; Moraes, Ricardo; Portugal, Paulo; Vasques, Francisco

2017-01-01

The IEEE 802.15.4/ZigBee cluster-tree topology is a suitable technology to deploy wide-scale Wireless Sensor Networks (WSNs). These networks are usually designed to support convergecast traffic, where all communication paths go through the PAN (Personal Area Network) coordinator. Nevertheless, peer-to-peer communication relationships may be also required for different types of WSN applications. That is the typical case of sensor and actuator networks, where local control loops must be closed using a reduced number of communication hops. The use of communication schemes optimised just for the support of convergecast traffic may result in higher network congestion and in a potentially higher number of communication hops. Within this context, this paper proposes an Alternative-Route Definition (ARounD) communication scheme for WSNs. The underlying idea of ARounD is to setup alternative communication paths between specific source and destination nodes, avoiding congested cluster-tree paths. These alternative paths consider shorter inter-cluster paths, using a set of intermediate nodes to relay messages during their inactive periods in the cluster-tree network. Simulation results show that the ARounD communication scheme can significantly decrease the end-to-end communication delay, when compared to the use of standard cluster-tree communication schemes. Moreover, the ARounD communication scheme is able to reduce the network congestion around the PAN coordinator, enabling the reduction of the number of message drops due to queue overflows in the cluster-tree network. PMID:28481245

Alternative Path Communication in Wide-Scale Cluster-Tree Wireless Sensor Networks Using Inactive Periods.

PubMed

Leão, Erico; Montez, Carlos; Moraes, Ricardo; Portugal, Paulo; Vasques, Francisco

2017-05-06

The IEEE 802.15.4/ZigBee cluster-tree topology is a suitable technology to deploy wide-scale Wireless Sensor Networks (WSNs). These networks are usually designed to support convergecast traffic, where all communication paths go through the PAN (Personal Area Network) coordinator. Nevertheless, peer-to-peer communication relationships may be also required for different types of WSN applications. That is the typical case of sensor and actuator networks, where local control loops must be closed using a reduced number of communication hops. The use of communication schemes optimised just for the support of convergecast traffic may result in higher network congestion and in a potentially higher number of communication hops. Within this context, this paper proposes an Alternative-Route Definition (ARounD) communication scheme for WSNs. The underlying idea of ARounD is to setup alternative communication paths between specific source and destination nodes, avoiding congested cluster-tree paths. These alternative paths consider shorter inter-cluster paths, using a set of intermediate nodes to relay messages during their inactive periods in the cluster-tree network. Simulation results show that the ARounD communication scheme can significantly decrease the end-to-end communication delay, when compared to the use of standard cluster-tree communication schemes. Moreover, the ARounD communication scheme is able to reduce the network congestion around the PAN coordinator, enabling the reduction of the number of message drops due to queue overflows in the cluster-tree network.

Enhancement of noradrenaline release by angiotensin II and bradykinin in mouse atria: evidence for cross-talk between Gq/11 protein- and Gi/o protein-coupled receptors

PubMed Central

Cox, S L; Schelb, V; Trendelenburg, A U; Starke, K

2000-01-01

The interaction between α2-autoreceptors and receptors for angiotensin (AT1) and bradykinin (B2) was studied in mouse isolated atria. The preparations were labelled with [3H]-noradrenaline and then superfused with desipramine-containing medium and stimulated electrically. Angiotensin II (10−11–10−7 M), angiotensin III (10−10–10−6 M) and bradykinin (10−11–10−7 M) enhanced the evoked overflow of tritium when preparations were stimulated with conditions that led to marked α2-autoinhibition (120 pulses at 3 Hz), but not when stimulated with conditions that led to little α2-autoinhibition (20 pulses at 50 Hz). Blockade of α-adrenoceptors by phentolamine (1 or 10 μM) reduced or abolished the effect of angiotensin II and bradykinin on the overflow response to 120 pulses at 3 Hz. Addition of the δ-opioid agonist [D-Ser2]-leucine enkephalin-Thr (DSLET, 0.1 μM), or of neuropeptide Y (0.1 μM), together with phentolamine, restored the effect of angiotensin II and bradykinin. The β-adrenoceptor agonist terbutaline (10−9–10−4 M) enhanced the evoked overflow of tritium irrespective of the degree of autoinhibition. The experiments show that (i) a marked prejunctional facilitatory effect of angiotensin and bradykinin in mouse isolated atria requires prejunctional α2-autoinhibition; (ii) in the absence of α2-autoinhibition, activation of other prejunctional Gi/o protein-coupled reeptors, namely opioid and neuropeptide Y receptors, restores a marked effect of angiotensin II and bradykinin; and (iii) the facilitatory effect of terbutaline is not dependent upon the degree of α2-autoinhibition. The findings indicate that the major part of the release-enhancing effect elicited through prejunctional Gq/11 protein-coupled receptors is due to disruption of an ongoing, α2-autoreceptor-triggered Gi/o protein mediated inhibition. PMID:10725257

Removal of micropollutants, facultative pathogenic and antibiotic resistant bacteria in a full-scale retention soil filter receiving combined sewer overflow.

PubMed

Scheurer, Marco; Heß, Stefanie; Lüddeke, Frauke; Sacher, Frank; Güde, Hans; Löffler, Herbert; Gallert, Claudia

2015-01-01

Combined sewer systems collect surface runoff as well as wastewater of industrial and domestic origin. During periods of heavy rainfall the capacity of the sewer system is exceeded and the overflow is discharged into receiving waters without any treatment. Consequently, combined sewer overflow (CSO) is considered as a major source of water pollution. This study investigates the effectiveness of a retention soil filter (RSF) for the removal of micropollutants as well as facultative pathogenic and antibiotic resistant bacteria from CSO. The removal of organic group parameters like total organic carbon was excellent and the removal efficiency for micropollutants of the RSF and the wastewater treatment plant (WWTP), which treats wastewater of the same origin during dry and normal weather conditions, was comparable. Compounds of high environmental concern like estrogens or certain pharmaceuticals, e.g. diclofenac, were completely eliminated or removed to a high degree during RSF passage. RSF treatment also reduced the number of E. coli, enterococci and staphylococci by 2.7, 2.2 and 2.4 log-units (median values), respectively. Obviously, some Staphylococcus species can better adapt to the conditions of the RSF than others as a shift of the abundance of the different species was observed when comparing the diversity of staphylococci obtained from the RSF influent and effluent. RSF treatment also decreased the absolute number of antibiotic resistant bacteria. The percentage of antibiotic resistant E. coli and staphylococci isolates also decreased during passage of the RSF, whereas the percentage of resistant enterococci did not change. For E. coli ampicillin and for enterococci and staphylococci erythromycin determined the antibiotic resistance level. The results demonstrate that RSFs can be considered as an adequate treatment option for CSO. The performance for the removal of micropollutants is comparable with a medium sized WWTP with conventional activated sludge treatment. The number of facultative pathogenic and antibiotic resistant bacteria was considerably decreased during RSF passage. However, as RSF effluents still contained antibiotic resistance genes and traces of micropollutants; receiving waters may still be at risk from negative environmental impacts.

Modafinil evokes striatal [(3)H]dopamine release and alters the subjective properties of stimulants.

PubMed

Dopheide, Marsha M; Morgan, Russell E; Rodvelt, Kelli R; Schachtman, Todd R; Miller, Dennis K

2007-07-30

Modafinil is a mild psychostimulant used for the treatment of sleep and arousal-related disorders, and has been considered a pharmacotherapy for cocaine and amphetamine dependence; however, modafinil's mechanism of action is largely unclear. The present study investigated modafinil using drug discrimination and slice superfusion techniques. Rats were trained to discriminate cocaine (1.6 or 5 mg/kg) or amphetamine (0.3 mg/kg) from saline injection for food reinforcement. Modafinil (64-128 mg/kg) substituted partially for both cocaine doses and amphetamine. Pretreatment with a lower modafinil dose (32 mg/kg) augmented the discriminative stimulus properties of cocaine (1.6 mg/kg dose group) and amphetamine. In neurochemical experiments, modafinil (100-300 microM) evoked [(3)H]overflow from rat striatal slices preloaded with [(3)H]dopamine in a concentration-dependent manner; however, modafinil was less potent and efficacious than amphetamine and nicotine. The dopamine transporter inhibitor nomifensine (10 microM) blocked modafinil-evoked [(3)H]overflow, and concentrations of modafinil (<100 microM) that did not have intrinsic activity attenuated amphetamine (1 and 3 microM)-evoked [(3)H]overflow. Modafinil-evoked [(3)H]overflow was not altered by the nicotinic acetylcholine receptor antagonist mecamylamine, and modafinil did not alter nicotine-evoked [(3)H]overflow, indicating that nicotinic acetylcholine receptors likely are not important for modafinil's mechanism of action. The present results indicate that modafinil evokes dopamine release from striatal neurons and is a psychostimulant that is pharmacologically similar to, but much less potent and efficacious than, amphetamine.

Chronic nicotine exposure selectively activates a carrier-mediated release of endogenous glutamate and aspartate from rat hippocampal synaptosomes.

PubMed

Marchi, Mario; Zappettini, Stefania; Olivero, Guendalina; Pittaluga, Anna; Grilli, Massimo

2012-05-01

The effect of chronic nicotine treatment on the release of endogenous glutamate (GLU), aspartate (ASP) and GABA evoked in vitro by KCl, 4-aminopyridine (4AP) and nicotinic agonists in synaptosomes of rat hippocampus was investigated. Rats were chronically administered with nicotine bitartrate or saline vehicle each for 14 days using osmotic mini-pumps. Hippocampal synaptosomes were stimulated with KCl, 4AP, nicotine or with choline (Ch) and 5-iodo-A-85380 dihydrochloride (5IA85380). The GLU and ASP overflow evoked by Ch, nicotine, KCl and 4AP were increased in treated animals while the nicotine-evoked GABA overflow was reduced and that evoked by Ch, KCl and 4AP was unaffected. The 5IA85380-evoked overflow of the three aminoacids (AAs) was always reduced. The increase of ASP and GLU overflow evoked by KCl, 4AP or Ch was blocked by dl-threo-β-benzyloxyaspartic acid (dl-TBOA), a carrier transporter inhibitor, and by inhibitors of the Na(+)/Ca(2+) exchangers 2-[[4-[(4-nitrophenyl)methoxy]phenyl]methyl]-4-thiazolidinecarboxylic acid ethyl ester (SN-6) and 2-[2-[4-(4-nitrobenzyloxy)phenyl]ethyl]isothiourea mesylate (KB-R7943). In conclusion long-term nicotine treatment may selectively increase GLU and ASP overflow elicited by KCl, 4AP and Ch through the activation of a carrier-mediated release mechanism and completely abolished the stimulatory effects of α4β2 nAChRs which modulate the release of all the three AA. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Screening Assessment of the Potential Impacts of Climate Change on Combined Sewer Overflow (CSO) Mitigation in the Great Lakes and New England Regions (Final Report)

EPA Science Inventory

EPA announced the availability of the report, A Screening Assessment of the Potential Impacts of Climate Change on Combined Sewer Overflow (CSO) Mitigation in the Great Lakes and New England Regions. This report is a screening-level assessment of the potential implications...

--No Title--

Science.gov Websites

;background-color:#ddd;border-bottom:3px solid #aaa;padding:8px;margin-top:12px;height:auto;overflow:hidden }#how_use_car{clear:both;background-color:#ddd;border-bottom:3px solid #aaa;padding:8px;margin-top:20px ;height:auto;overflow:hidden}#results{clear:both;background-color:#ddd;border-bottom:3px solid #aaa;padding:8px

On the Nature of the Mesoscale Variability in Denmark Strait

NASA Astrophysics Data System (ADS)

Pickart, Robert; von Appen, Wilken; Mastropole, Dana; Valdimarsson, Hedinn; Vage, Kjetil; Jonsson, Steingriumur; Jochumsen, Kerstin; Girton, James

2017-04-01

The dense overflow through Denmark Strait is the largest contributor to the lower limb of the Atlantic Meridional Overturning Circulation. As such, it is important to understand the sources of water feeding the overflow and how the water negotiates the sill as it passes into the Irminger Sea. Here we use a large collection of shipboard hydrographic transects occupied across the strait, together with 6-years of mooring data from the sill, to investigate the water masses and mesoscale variability of the overflow water. Two dominant types of mesoscale features were identified, referred to as a "bolus" and a "pulse". The former is a large lens of weakly stratified water corresponding to a slight increase in along-strait velocity. The latter is a thin layer with greater stratification and strongly enhanced along-strait flow. The boluses, which are often noted in the historical literature, are associated with cyclonic circulation, while pulses, which have not been previously identified, are associated with anti-cyclonic circulation. Both features result in increased transport of overflow water. It is argued that these fluctuations at the sill trigger energetic variability downstream in the Deep Western Boundary Current.

Protective effect of agmatine on ischemia/reperfusion-induced renal injury in rats.

PubMed

Sugiura, Takahiro; Tsutsui, Hidenobu; Takaoka, Masanori; Kobuchi, Shuhei; Hayashi, Kentaro; Fujii, Toshihide; Matsumura, Yasuo

2008-03-01

Enhanced renal sympathetic nerve activity (RSNA) during ischemic period and the renal venous norepinephrine (NE) overflow after reperfusion play important roles in the development of ischemic/reperfusion (I/R)-induced acute renal failure (ARF) in rats. This study evaluated whether agmatine, which is known to reduce sympathetic nerve activity and NE overflow by electrical stimulation, would prevent the I/R-induced renal dysfunction. Ischemic ARF was induced by clamping the left renal artery and vein for 45 minutes followed by reperfusion 2 weeks after the contralateral nephrectomy. Intravenous (IV) injection of agmatine (100 and 300 micromol/kg) to ischemic ARF rats dose-dependently suppressed the enhanced RSNA and attenuated the I/R-induced renal dysfunction and histological damage. Intracerebroventricular (ICV) injection of agmatine (600 nmol/kg) to ischemic ARF rats suppressed the enhanced RSNA during the ischemic period and attenuated the I/R-induced renal injury. Furthermore, both IV and ICV injection of agmatine significantly suppressed the renal venous NE overflow after the reperfusion. These results indicate that agmatine prevents the development of I/R-induced renal injury, and the effect is accompanied by suppression of the enhanced RSNA during ischemic period and NE overflow from renal sympathetic nerve endings.

Locations of Combined Sewer Overflow Outfalls - US EPA Region 3

EPA Pesticide Factsheets

This data layer identifies the locations of Combined sewer overflow outfalls. Combined sewer systems are sewers that are designed to collect rainwater runoff, domestic sewage, and industrial wastewater in the same pipe. Most of the time, combined sewer systems transport all of their wastewater to a sewage treatment plant, where it is treated and then discharged to a water body. During periods of heavy rainfall or snowmelt, however, the wastewater volume in a combined sewer system can exceed the capacity of the sewer system or treatment plant. For this reason, combined sewer systems are designed to overflow occasionally and discharge excess untreated wastewater directly to nearby streams, rivers, or other water bodies. For further information visit: http://cfpub1.epa.gov/npdes/home.cfm?program_id=5

Cathodal transcranial direct current stimulation in children with dystonia: a sham-controlled study.

PubMed

Young, Scott J; Bertucco, Matteo; Sanger, Terence D

2014-02-01

Increased motor cortex excitability is a common finding in dystonia, and transcranial direct current stimulation can reduce motor cortex excitability. In an earlier study, we found that cathodal direct-current stimulation decreased motor overflow for some children with dystonia. To investigate this observation further, we performed a sham-controlled, double-blind, crossover study of 14 children with dystonia. We found a significant reduction in overflow following real stimulation, when participants performed the experimental task with the hand contralateral to the cathode. While these results suggest that cathodal stimulation may help some children to reduce involuntary overflow, the size of the effect is small. Further research will need to investigate ways to increase the magnitude of the effect of cathodal transcranial direct current stimulation.

Use long short-term memory to enhance Internet of Things for combined sewer overflow monitoring

NASA Astrophysics Data System (ADS)

Zhang, Duo; Lindholm, Geir; Ratnaweera, Harsha

2018-01-01

Combined sewer overflow causes severe water pollution, urban flooding and reduced treatment plant efficiency. Understanding the behavior of CSO structures is vital for urban flooding prevention and overflow control. Neural networks have been extensively applied in water resource related fields. In this study, we collect data from an Internet of Things monitoring CSO structure and build different neural network models for simulating and predicting the water level of the CSO structure. Through a comparison of four different neural networks, namely multilayer perceptron (MLP), wavelet neural network (WNN), long short-term memory (LSTM) and gated recurrent unit (GRU), the LSTM and GRU present superior capabilities for multi-step-ahead time series prediction. Furthermore, GRU achieves prediction performances similar to LSTM with a quicker learning curve.

Environmental Transport of Emerging Human-Pathogenic Cryptosporidium Species and Subtypes through Combined Sewer Overflow and Wastewater

PubMed Central

Huang, Chengchen; Hu, Yue; Wang, Lin; Wang, Yuanfei; Li, Na; Guo, Yaqiong; Xiao, Lihua

2017-01-01

ABSTRACT The environmental transport of Cryptosporidium spp. through combined sewer overflow (CSO) and the occurrence of several emerging human-pathogenic Cryptosporidium species in developing countries remain unclear. In this study, we collected 40 CSO samples and 40 raw wastewater samples from Shanghai, China, and examined them by PCR and DNA sequencing for Cryptosporidium species (targeting the small subunit rRNA gene) and Giardia duodenalis (targeting the triosephosphate isomerase, β-giardin, and glutamate dehydrogenase genes) and Enterocytozoon bieneusi (targeting the ribosomal internal transcribed spacer) genotypes. Human-pathogenic Cryptosporidium species were further subtyped by sequence analysis of the 60-kDa glycoprotein gene, with additional multilocus sequence typing on the emerging zoonotic pathogen Cryptosporidium ubiquitum. Cryptosporidium spp., G. duodenalis, and E. bieneusi were detected in 12 and 15, 33 and 32, and 37 and 40 CSO and wastewater samples, respectively, including 10 Cryptosporidium species, 3 G. duodenalis assemblages, and 8 E. bieneusi genotypes. In addition to Cryptosporidium hominis and Cryptosporidium parvum, two new pathogens identified in industrialized nations, C. ubiquitum and Cryptosporidium viatorum, were frequently detected. The two novel C. ubiquitum subtype families identified appeared to be genetic recombinants of known subtype families. Similarly, the dominant group 1 E. bieneusi genotypes and G. duodenalis subassemblage AII are known human pathogens. The similar distribution of human-pathogenic Cryptosporidium species and E. bieneusi and G. duodenalis genotypes between wastewater and CSO samples reaffirms that storm overflow is potentially a significant contamination source of pathogens in surface water. The frequent identification of C. ubiquitum and C. viatorum in urban wastewater suggests that these newly identified human pathogens may be endemic in China. IMPORTANCE Cryptosporidium spp., Giardia duodenalis, and Enterocytozoon bieneusi are major waterborne pathogens. Their transport into surface water through combined sewer overflow, which remains largely untreated in developing countries, has not been examined. In addition, the identification of these pathogens to genotypes and subtypes in urban storm overflow and wastewater is necessary for rapid and accurate assessment of pathogen transmission in humans and transport in the environment. Data from this study suggest that, like untreated urban wastewater, combined sewer overflow is commonly contaminated with human-pathogenic Cryptosporidium, G. duodenalis, and E. bieneusi genotypes and subtypes, and urban storm overflow potentially plays a significant role in the contamination of drinking source water and recreational water with human pathogens. They also indicate that Cryptosporidium ubiquitum and Cryptosporidium viatorum, two newly identified human pathogens, may be common in China, and genetic recombination can lead to the emergence of novel C. ubiquitum subtype families. PMID:28600310

Performance and Application of Parallel OVERFLOW Codes on Distributed and Shared Memory Platforms

NASA Technical Reports Server (NTRS)

Djomehri, M. Jahed; Rizk, Yehia M.

1999-01-01

The presentation discusses recent studies on the performance of the two parallel versions of the aerodynamics CFD code, OVERFLOW_MPI and _MLP. Developed at NASA Ames, the serial version, OVERFLOW, is a multidimensional Navier-Stokes flow solver based on overset (Chimera) grid technology. The code has recently been parallelized in two ways. One is based on the explicit message-passing interface (MPI) across processors and uses the _MPI communication package. This approach is primarily suited for distributed memory systems and workstation clusters. The second, termed the multi-level parallel (MLP) method, is simple and uses shared memory for all communications. The _MLP code is suitable on distributed-shared memory systems. For both methods, the message passing takes place across the processors or processes at the advancement of each time step. This procedure is, in effect, the Chimera boundary conditions update, which is done in an explicit "Jacobi" style. In contrast, the update in the serial code is done in more of the "Gauss-Sidel" fashion. The programming efforts for the _MPI code is more complicated than for the _MLP code; the former requires modification of the outer and some inner shells of the serial code, whereas the latter focuses only on the outer shell of the code. The _MPI version offers a great deal of flexibility in distributing grid zones across a specified number of processors in order to achieve load balancing. The approach is capable of partitioning zones across multiple processors or sending each zone and/or cluster of several zones into a single processor. The message passing across the processors consists of Chimera boundary and/or an overlap of "halo" boundary points for each partitioned zone. The MLP version is a new coarse-grain parallel concept at the zonal and intra-zonal levels. A grouping strategy is used to distribute zones into several groups forming sub-processes which will run in parallel. The total volume of grid points in each group are approximately balanced. A proper number of threads are initially allocated to each group, and in subsequent iterations during the run-time, the number of threads are adjusted to achieve load balancing across the processes. Each process exploits the multitasking directives already established in Overflow.

Using Agent-Based Modeling to Enhance System-Level Real-time Control of Urban Stormwater Systems

NASA Astrophysics Data System (ADS)

Rimer, S.; Mullapudi, A. M.; Kerkez, B.

2017-12-01

The ability to reduce combined-sewer overflow (CSO) events is an issue that challenges over 800 U.S. municipalities. When the volume of a combined sewer system or wastewater treatment plant is exceeded, untreated wastewater then overflows (a CSO event) into nearby streams, rivers, or other water bodies causing localized urban flooding and pollution. The likelihood and impact of CSO events has only exacerbated due to urbanization, population growth, climate change, aging infrastructure, and system complexity. Thus, there is an urgent need for urban areas to manage CSO events. Traditionally, mitigating CSO events has been carried out via time-intensive and expensive structural interventions such as retention basins or sewer separation, which are able to reduce CSO events, but are costly, arduous, and only provide a fixed solution to a dynamic problem. Real-time control (RTC) of urban drainage systems using sensor and actuator networks has served as an inexpensive and versatile alternative to traditional CSO intervention. In particular, retrofitting individual stormwater elements for sensing and automated active distributed control has been shown to significantly reduce the volume of discharge during CSO events, with some RTC models demonstrating a reduction upwards of 90% when compared to traditional passive systems. As more stormwater elements become retrofitted for RTC, system-level RTC across complete watersheds is an attainable possibility. However, when considering the diverse set of control needs of each of these individual stormwater elements, such system-level RTC becomes a far more complex problem. To address such diverse control needs, agent-based modeling is employed such that each individual stormwater element is treated as an autonomous agent with a diverse decision making capabilities. We present preliminary results and limitations of utilizing the agent-based modeling computational framework for the system-level control of diverse, interacting stormwater elements.

Superframe Duration Allocation Schemes to Improve the Throughput of Cluster-Tree Wireless Sensor Networks

PubMed Central

Leão, Erico; Montez, Carlos; Moraes, Ricardo; Portugal, Paulo; Vasques, Francisco

2017-01-01

The use of Wireless Sensor Network (WSN) technologies is an attractive option to support wide-scale monitoring applications, such as the ones that can be found in precision agriculture, environmental monitoring and industrial automation. The IEEE 802.15.4/ZigBee cluster-tree topology is a suitable topology to build wide-scale WSNs. Despite some of its known advantages, including timing synchronisation and duty-cycle operation, cluster-tree networks may suffer from severe network congestion problems due to the convergecast pattern of its communication traffic. Therefore, the careful adjustment of transmission opportunities (superframe durations) allocated to the cluster-heads is an important research issue. This paper proposes a set of proportional Superframe Duration Allocation (SDA) schemes, based on well-defined protocol and timing models, and on the message load imposed by child nodes (Load-SDA scheme), or by number of descendant nodes (Nodes-SDA scheme) of each cluster-head. The underlying reasoning is to adequately allocate transmission opportunities (superframe durations) and parametrize buffer sizes, in order to improve the network throughput and avoid typical problems, such as: network congestion, high end-to-end communication delays and discarded messages due to buffer overflows. Simulation assessments show how proposed allocation schemes may clearly improve the operation of wide-scale cluster-tree networks. PMID:28134822

Determinants of quality, latency, and amount of Stack Overflow answers about recent Android APIs

PubMed Central

Filkov, Vladimir

2018-01-01

Stack Overflow is a popular crowdsourced question and answer website for programming-related issues. It is an invaluable resource for software developers; on average, questions posted there get answered in minutes to an hour. Questions about well established topics, e.g., the coercion operator in C++, or the difference between canonical and class names in Java, get asked often in one form or another, and answered very quickly. On the other hand, questions on previously unseen or niche topics take a while to get a good answer. This is particularly the case with questions about current updates to or the introduction of new application programming interfaces (APIs). In a hyper-competitive online market, getting good answers to current programming questions sooner could increase the chances of an app getting released and used. So, can developers anyhow, e.g., hasten the speed to good answers to questions about new APIs? Here, we empirically study Stack Overflow questions pertaining to new Android APIs and their associated answers. We contrast the interest in these questions, their answer quality, and timeliness of their answers to questions about old APIs. We find that Stack Overflow answerers in general prioritize with respect to currentness: questions about new APIs do get more answers, but good quality answers take longer. We also find that incentives in terms of question bounties, if used appropriately, can significantly shorten the time and increase answer quality. Interestingly, no operationalization of bounty amount shows significance in our models. In practice, our findings confirm the value of bounties in enhancing expert participation. In addition, they show that the Stack Overflow style of crowdsourcing, for all its glory in providing answers about established programming knowledge, is less effective with new API questions. PMID:29547620

In vivo microdialysis of noradrenaline overflow: effects of alpha-adrenoceptor agonists and antagonists measured by cumulative concentration-response curves.

PubMed Central

van Veldhuizen, M. J.; Feenstra, M. G.; Heinsbroek, R. P.; Boer, G. J.

1993-01-01

1. The purpose of the present study was to compare the effects of several alpha-adrenoceptor agonists and antagonists on cerebral cortical overflow of endogenous noradrenaline (NA) in freely moving rats. One or two days after the implantation of transcerebral dialysis tubes in the frontoparietal cortex, extracellular NA levels were monitored on-line with high performance liquid chromatography and electrochemical detection. The drugs were applied locally via the dialysis membrane, and effects on NA overflow were determined in cumulative concentration-response curves. 2. The average basal cortical NA overflow of all experiments was 0.25 pg min-1. The alpha 2-adrenoceptor agonists caused a concentration-dependent decrease in NA levels. UK-14,304 was the most potent and B-HT 933 the least potent agonist. The maximal decrease in NA overflow was to 10-15% of control levels after UK-14,304 or moxonidine, to 30% after clonidine and to 50% after B-HT 933 administration. Continuous activation of the presynaptic alpha 2-adrenoceptor with 10(-6) M UK-14,304 caused a decrease in NA levels to 40-50% of basal levels. This decrease was reached within 1 h and remained stable for the entire 3 h measurement period. The alpha 1-adrenoceptor agonists, phenylephrine and methoxamine, induced an increase in NA levels to 225% and 300%, respectively, at a concentration of 10(-3) M. 3. Local application of alpha 2-adrenoceptor antagonists caused an increase in NA levels, with idazoxan being more potent than piperoxan. Yohimbine did not cause any significant change. 4. All drugs used in these in vivo experiments had in vitro recoveries across the dialysis membrane between 10 and 20%.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:8102934

Acetate scavenging activity in Escherichia coli: interplay of acetyl-CoA synthetase and the PEP-glyoxylate cycle in chemostat cultures.

PubMed

Renilla, Sergio; Bernal, Vicente; Fuhrer, Tobias; Castaño-Cerezo, Sara; Pastor, José M; Iborra, José L; Sauer, Uwe; Cánovas, Manuel

2012-03-01

Impairment of acetate production in Escherichia coli is crucial for the performance of many biotechnological processes. Aerobic production of acetate (or acetate overflow) results from changes in the expression of central metabolism genes. Acetyl-CoA synthetase scavenges extracellular acetate in glucose-limited cultures. Once converted to acetyl-CoA, it can be catabolized by the tricarboxylic acid cycle or the glyoxylate pathway. In this work, we assessed the significance of these pathways on acetate overflow during glucose excess and limitation. Gene expression, enzyme activities, and metabolic fluxes were studied in E. coli knock-out mutants related to the glyoxylate pathway operon and its regulators. The relevance of post-translational regulation by AceK-mediated phosphorylation of isocitrate dehydrogenase for pathway functionality was underlined. In chemostat cultures performed at increasing dilution rates, acetate overflow occurs when growing over a threshold glucose uptake rate. This threshold was not affected in a glyoxylate-pathway-deficient strain (lacking isocitrate lyase, the first enzyme of the pathway), indicating that it is not relevant for acetate overflow. In carbon-limited chemostat cultures, gluconeogenesis (maeB, sfcA, and pck), the glyoxylate operon and, especially, acetyl-CoA synthetase are upregulated. A mutant in acs (encoding acetyl-CoA synthetase) produced acetate at all dilution rates. This work demonstrates that, in E. coli, acetate production occurs at all dilution rates and that overflow is the result of unbalanced synthesis and scavenging activities. The over-expression of acetyl-CoA synthetase by cAMP-CRP-dependent induction limits this phenomenon in cultures consuming glucose at low rate, ensuring the recycling of the acetyl-CoA and acetyl-phosphate pools, although establishing an energy-dissipating substrate cycle.

Determinants of quality, latency, and amount of Stack Overflow answers about recent Android APIs.

PubMed

Kavaler, David; Filkov, Vladimir

2018-01-01

Stack Overflow is a popular crowdsourced question and answer website for programming-related issues. It is an invaluable resource for software developers; on average, questions posted there get answered in minutes to an hour. Questions about well established topics, e.g., the coercion operator in C++, or the difference between canonical and class names in Java, get asked often in one form or another, and answered very quickly. On the other hand, questions on previously unseen or niche topics take a while to get a good answer. This is particularly the case with questions about current updates to or the introduction of new application programming interfaces (APIs). In a hyper-competitive online market, getting good answers to current programming questions sooner could increase the chances of an app getting released and used. So, can developers anyhow, e.g., hasten the speed to good answers to questions about new APIs? Here, we empirically study Stack Overflow questions pertaining to new Android APIs and their associated answers. We contrast the interest in these questions, their answer quality, and timeliness of their answers to questions about old APIs. We find that Stack Overflow answerers in general prioritize with respect to currentness: questions about new APIs do get more answers, but good quality answers take longer. We also find that incentives in terms of question bounties, if used appropriately, can significantly shorten the time and increase answer quality. Interestingly, no operationalization of bounty amount shows significance in our models. In practice, our findings confirm the value of bounties in enhancing expert participation. In addition, they show that the Stack Overflow style of crowdsourcing, for all its glory in providing answers about established programming knowledge, is less effective with new API questions.

Increased formate overflow is a hallmark of oxidative cancer.

PubMed

Meiser, Johannes; Schuster, Anne; Pietzke, Matthias; Vande Voorde, Johan; Athineos, Dimitris; Oizel, Kristell; Burgos-Barragan, Guillermo; Wit, Niek; Dhayade, Sandeep; Morton, Jennifer P; Dornier, Emmanuel; Sumpton, David; Mackay, Gillian M; Blyth, Karen; Patel, Ketan J; Niclou, Simone P; Vazquez, Alexei

2018-04-10

Formate overflow coupled to mitochondrial oxidative metabolism\\ has been observed in cancer cell lines, but whether that takes place in the tumor microenvironment is not known. Here we report the observation of serine catabolism to formate in normal murine tissues, with a relative rate correlating with serine levels and the tissue oxidative state. Yet, serine catabolism to formate is increased in the transformed tissue of in vivo models of intestinal adenomas and mammary carcinomas. The increased serine catabolism to formate is associated with increased serum formate levels. Finally, we show that inhibition of formate production by genetic interference reduces cancer cell invasion and this phenotype can be rescued by exogenous formate. We conclude that increased formate overflow is a hallmark of oxidative cancers and that high formate levels promote invasion via a yet unknown mechanism.

Competitive resource allocation to metabolic pathways contributes to overflow metabolisms and emergent properties in cross-feeding microbial consortia.

PubMed

Carlson, Ross P; Beck, Ashley E; Phalak, Poonam; Fields, Matthew W; Gedeon, Tomas; Hanley, Luke; Harcombe, William R; Henson, Michael A; Heys, Jeffrey J

2018-04-17

Resource scarcity is a common stress in nature and has a major impact on microbial physiology. This review highlights microbial acclimations to resource scarcity, focusing on resource investment strategies for chemoheterotrophs from the molecular level to the pathway level. Competitive resource allocation strategies often lead to a phenotype known as overflow metabolism; the resulting overflow byproducts can stabilize cooperative interactions in microbial communities and can lead to cross-feeding consortia. These consortia can exhibit emergent properties such as enhanced resource usage and biomass productivity. The literature distilled here draws parallels between in silico and laboratory studies and ties them together with ecological theories to better understand microbial stress responses and mutualistic consortia functioning. © 2018 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

Laminar Heating Validation of the OVERFLOW Code

NASA Technical Reports Server (NTRS)

Lillard, Randolph P.; Dries, Kevin M.

2005-01-01

OVERFLOW, a structured finite difference code, was applied to the solution of hypersonic laminar flow over several configurations assuming perfect gas chemistry. By testing OVERFLOW's capabilities over several configurations encompassing a variety of flow physics a validated laminar heating was produced. Configurations tested were a flat plate at 0 degrees incidence, a sphere, a compression ramp, and the X-38 re-entry vehicle. This variety of test cases shows the ability of the code to predict boundary layer flow, stagnation heating, laminar separation with re-attachment heating, and complex flow over a three-dimensional body. In addition, grid resolutions studies were done to give recommendations for the correct number of off-body points to be applied to generic problems and for wall-spacing values to capture heat transfer and skin friction. Numerical results show good comparison to the test data for all the configurations.

OVERFLOW Validation for Predicting Plume Impingement of Underexpanded Axisymmetric Jets onto Angled Flat Plates

NASA Technical Reports Server (NTRS)

Lee, Henry C.; Klopfer, Goetz

2011-01-01

This report documents how OVERFLOW, a computational fluid dynamics code, predicts plume impingement of underexpanded axisymmetric jets onto both perpendicular and inclined flat plates. The effects of the plume impinging on a range of plate inclinations varying from 90deg to 30deg are investigated and compared to the experimental results in Reference 1 and 2. The flow fields are extremely complex due to the interaction between the shock waves from the free jet and those deflected by the plate. Additionally, complex mixing effects create very intricate structures in the flow. The experimental data is very limited, so these validation studies will focus only on cold plume impingement on flat and inclined plates. This validation study will help quantify the error in the OVERFLOW simulation when applied to stage separation scenarios.

Hydrologic Analysis and Two-Dimensional Simulation of Flow at State Highway 17 crossing the Gasconade River near Waynesville, Missouri

USGS Publications Warehouse

Huizinga, Richard J.

2008-01-01

In cooperation with the Missouri Department of Transportation, the U.S. Geological Survey determined hydrologic and hydraulic parameters for the Gasconade River at the site of a proposed bridge replacement and highway realignment of State Highway 17 near Waynesville, Missouri. Information from a discontinued streamflow-gaging station on the Gasconade River near Waynesville was used to determine streamflow statistics for analysis of the 25-, 50-, 100-, and 500-year floods at the site. Analysis of the streamflow-gaging stations on the Gasconade River upstream and downstream from Waynesville indicate that flood peaks attenuate between the upstream gaging station near Hazelgreen and the Waynesville gaging station, such that the peak discharge observed on the Gasconade River near Waynesville will be equal to or only slightly greater (7 percent or less) than that observed near Hazelgreen. A flood event occurred on the Gasconade River in March 2008, and a flood measurement was obtained near the peak at State Highway 17. The elevation of high-water marks from that event indicated it was the highest measured flood on record with a measured discharge of 95,400 cubic feet per second, and a water-surface elevation of 766.18 feet near the location of the Waynesville gaging station. The measurements obtained for the March flood resulted in a shift of the original stage-discharge relation for the Waynesville gaging station, and the streamflow statistics were modified based on the new data. A two-dimensional hydrodynamic flow model was used to simulate flow conditions on the Gasconade River in the vicinity of State Highway 17. A model was developed that represents existing (2008) conditions on State Highway 17 (the 'model of existing conditions'), and was calibrated to the floods of March 20, 2008, December 4, 1982, and April 14, 1945. Modifications were made to the model of existing conditions to create a model that represents conditions along the same reach of the Gasconade River with preliminary proposed replacement bridges and realignment of State Highway 17 (the 'model of proposed conditions'). The models of existing and proposed conditions were used to simulate the 25-, 50-, 100-, and 500-year recurrence floods, as well as the March 20, 2008 flood. Results from the model of proposed conditions show that the proposed replacement structures and realignment of State Highway 17 will result in additional backwater upstream from State Highway 17 ranging from approximately 0.18 foot for the 25-year flood to 0.32 foot for the 500-year flood. Velocity magnitudes in the proposed overflow structures were greater than in the existing structures [by as much as 4.9 feet per second in the left (west) overflow structure for the 500-year flood], and shallow, high-velocity flow occurs at the upstream edges of the abutments of the proposed overflow structures in the 100- and 500-year floods where flow overtops parts of the existing road embankment that will be left in place in the proposed scenario. Velocity magnitude in the main channel of the model of proposed conditions increased by a maximum of 1.2 feet per second over the model of existing conditions, with the maximum occurring approximately 1,500 feet downstream from existing main channel structure J-802.

Implementation of Preconditioned Dual-Time Procedures in OVERFLOW

NASA Technical Reports Server (NTRS)

Pandya, Shishir A.; Venkateswaran, Sankaran; Pulliam, Thomas H.; Kwak, Dochan (Technical Monitor)

2003-01-01

Preconditioning methods have become the method of choice for the solution of flowfields involving the simultaneous presence of low Mach and transonic regions. It is well known that these methods are important for insuring accurate numerical discretization as well as convergence efficiency over various operating conditions such as low Mach number, low Reynolds number and high Strouhal numbers. For unsteady problems, the preconditioning is introduced within a dual-time framework wherein the physical time-derivatives are used to march the unsteady equations and the preconditioned time-derivatives are used for purposes of numerical discretization and iterative solution. In this paper, we describe the implementation of the preconditioned dual-time methodology in the OVERFLOW code. To demonstrate the performance of the method, we employ both simple and practical unsteady flowfields, including vortex propagation in a low Mach number flow, flowfield of an impulsively started plate (Stokes' first problem) arid a cylindrical jet in a low Mach number crossflow with ground effect. All the results demonstrate that the preconditioning algorithm is responsible for improvements to both numerical accuracy and convergence efficiency and, thereby, enables low Mach number unsteady computations to be performed at a fraction of the cost of traditional time-marching methods.

Overflow control valve

DOEpatents

Hundal, Rolv; Kessinger, Boyd A.; Parlak, Edward A.

1984-07-24

An overflow control valve for use in a liquid sodium coolant pump tank which valve can be extended to create a seal with the pump tank wall or retracted to break the seal thereby accommodating valve removal. An actuating shaft which controls valve disc position also has cams which bear on roller surfaces to force retraction of a sliding cylinder against spring tension to retract the cylinder from sealing contact with the pump tank.

Performance of OVERFLOW-D Applications based on Hybrid and MPI Paradigms on IBM Power4 System

NASA Technical Reports Server (NTRS)

Djomehri, M. Jahed; Biegel, Bryan (Technical Monitor)

2002-01-01

This report briefly discusses our preliminary performance experiments with parallel versions of OVERFLOW-D applications. These applications are based on MPI and hybrid paradigms on the IBM Power4 system here at the NAS Division. This work is part of an effort to determine the suitability of the system and its parallel libraries (MPI/OpenMP) for specific scientific computing objectives.

Climate impacts of parameterized Nordic Sea overflows

NASA Astrophysics Data System (ADS)

Danabasoglu, Gokhan; Large, William G.; Briegleb, Bruce P.

2010-11-01

A new overflow parameterization (OFP) of density-driven flows through ocean ridges via narrow, unresolved channels has been developed and implemented in the ocean component of the Community Climate System Model version 4. It represents exchanges from the Nordic Seas and the Antarctic shelves, associated entrainment, and subsequent injection of overflow product waters into the abyssal basins. We investigate the effects of the parameterized Denmark Strait (DS) and Faroe Bank Channel (FBC) overflows on the ocean circulation, showing their impacts on the Atlantic Meridional Overturning Circulation and the North Atlantic climate. The OFP is based on the Marginal Sea Boundary Condition scheme of Price and Yang (1998), but there are significant differences that are described in detail. Two uncoupled (ocean-only) and two fully coupled simulations are analyzed. Each pair consists of one case with the OFP and a control case without this parameterization. In both uncoupled and coupled experiments, the parameterized DS and FBC source volume transports are within the range of observed estimates. The entrainment volume transports remain lower than observational estimates, leading to lower than observed product volume transports. Due to low entrainment, the product and source water properties are too similar. The DS and FBC overflow temperature and salinity properties are in better agreement with observations in the uncoupled case than in the coupled simulation, likely reflecting surface flux differences. The most significant impact of the OFP is the improved North Atlantic Deep Water penetration depth, leading to a much better comparison with the observational data and significantly reducing the chronic, shallow penetration depth bias in level coordinate models. This improvement is due to the deeper penetration of the southward flowing Deep Western Boundary Current. In comparison with control experiments without the OFP, the abyssal ventilation rates increase in the North Atlantic. In the uncoupled simulation with the OFP, the warm bias of the control simulation in the deep North Atlantic is substantially reduced along with salinity bias reductions in the northern North Atlantic. There are similar but more modest bias reductions in the deep temperature and salinity distributions especially in the northern North Atlantic in the coupled OFP case. In coupled simulations, there are noticeable impacts of the OFP on climate. The sea surface temperatures (SSTs) are warmer by more than 5°C off the North American coast and by more than 1°C in the Nordic Sea with the OFP. The surface heat fluxes mostly act to diminish these SST changes. There are related changes in the sea level pressure, leading to about 15% weaker westerly wind stress in the northern North Atlantic. In response to the warmer Nordic Sea SSTs, there are reductions in the sea ice extent, improving comparisons with observations. Although the OFP cases improve many aspects of the simulations compared to observations, some significant biases remain, more in coupled than in uncoupled simulations.

Biological assessment and streambed-sediment chemistry of streams in the Indianapolis metropolitan area, Indiana, 2003–2008

USGS Publications Warehouse

Voelker, David C.

2012-01-01

During 2003–2008, the U.S. Geological Survey sampled 13 sites in the Indianapolis metropolitan area in Indiana for benthic invertebrates, fish communities, and streambed-sediment chemistry. Data from seven White River sites and six tributary sites complement surface-water chemistry data collected by the Indianapolis Department of Public Works. The information is being used to assess changes in water quality in conjunction with the City's programs to reduce combined sewer overflows and other point and nonpoint sources of pollution in the Indianapolis area. During the study, 233 benthic-invertebrate taxa were identified from which the Ephemeroptera, Plecoptera, and Trichoptera (EPT) Index, the Hilsenhoff Biotic Index (HBI), and the Invertebrate Community Index (ICI) were calculated. EPT index scores ranged from 2 to 16 on the White River and from 2 to 17 on the tributaries. EPT index scores indicate that these pollution-intolerant taxa are more prevalent upstream from and away from the combined-sewer areas of Indianapolis. HBI scores from sites on the White River ranged from 4.67 (good) to 9.55 (very poor), whereas on the tributaries, scores ranged from 4.21 (very good) to 8.14 (poor). Lower HBI scores suggest that less organic pollution was present and, like the EPT scores, indicate better conditions where combined-sewer overflows (CSOs) are not present. Similarly, ICI scores indicated better conditions upstream from the CSO outfalls on the White River. White River scores ranged from 12 to 46, where higher ICI scores indicate better conditions in the benthic-invertebrate community. ICI scores at the tributary sites ranged from 12 to 52, with the highest scores on streams without CSOs.

Late Pliocene-Early Pleistocene oscillations in Mediterranean Overflow water: a new perspective from the Iberian Margin

NASA Astrophysics Data System (ADS)

Alonso-Garcia, M.; Salgueiro, E.; Rodrigues, T.; Alvarez Zarikian, C. A.; Kuhnert, H.; Roehl, U.; Voelker, A. H. L.; Sierro, F. J.; Abrantes, F. F. G.

2016-12-01

During the Late Pliocene to the Early Pleistocene the Earth experienced a transition from the warm Pliocene climate, with high greenhouse gases concentrations, to a colder climate with significant expansion of ice-sheets in the Northern Hemisphere and alternation between glacial and interglacial periods. Several hypotheses have been put forward to explain this climate transition, and recently, the enhancement of the Mediterranean Overflow Water (MOW) was suggested to have played a major role since it contributes high salinity water to the North Atlantic. Sedimentary records from the last glacial cycle and modelling experiments evidenced this link and suggested that the MOW injection of salty water to intermediate depths may have enhanced the upper branch of NADW, which ultimately reinvigorated the whole Atlantic Meridional overturning circulation. Here we present sedimentological and paleontological data from Site U1391 (37° N; 9° W; 1085 m water depth), recovered on the Southwest Iberian Margin during the Integrated Ocean Drilling Program (IODP) Expedition 339. This site is located in a plastered drift in the path of the MOW and offers high sedimentation rates to perform high resolution studies of past climatic and oceanographic conditions. In this study, we combined XRF geochemical data (from X-ray fluorescence core scanning) with grain-size, benthic foraminifer δ18O and δ13C, and ostracod records to reconstruct deep water circulation and climatic conditions during the Plio-Pleistocene transition. The high-resolution record of the XRF analysis indicates a switch in the response of MOW to climate changes across this transition. Early Pleistocene glacial-interglacial cycles show a stronger coupling between MOW oscillations (as indicated by the Zr/Al ratio) and sea surface temperature conditions (as indicated by the Ca/Ti ratio).

National Scale Rainfall Map Based on Linearly Interpolated Data from Automated Weather Stations and Rain Gauges

NASA Astrophysics Data System (ADS)

Alconis, Jenalyn; Eco, Rodrigo; Mahar Francisco Lagmay, Alfredo; Lester Saddi, Ivan; Mongaya, Candeze; Figueroa, Kathleen Gay

2014-05-01

In response to the slew of disasters that devastates the Philippines on a regular basis, the national government put in place a program to address this problem. The Nationwide Operational Assessment of Hazards, or Project NOAH, consolidates the diverse scientific research being done and pushes the knowledge gained to the forefront of disaster risk reduction and management. Current activities of the project include installing rain gauges and water level sensors, conducting LIDAR surveys of critical river basins, geo-hazard mapping, and running information education campaigns. Approximately 700 automated weather stations and rain gauges installed in strategic locations in the Philippines hold the groundwork for the rainfall visualization system in the Project NOAH web portal at http://noah.dost.gov.ph. The system uses near real-time data from these stations installed in critical river basins. The sensors record the amount of rainfall in a particular area as point data updated every 10 to 15 minutes. The sensor sends the data to a central server either via GSM network or satellite data transfer for redundancy. The web portal displays the sensors as a placemarks layer on a map. When a placemark is clicked, it displays a graph of the rainfall data for the past 24 hours. The rainfall data is harvested by batch determined by a one-hour time frame. The program uses linear interpolation as the methodology implemented to visually represent a near real-time rainfall map. The algorithm allows very fast processing which is essential in near real-time systems. As more sensors are installed, precision is improved. This visualized dataset enables users to quickly discern where heavy rainfall is concentrated. It has proven invaluable on numerous occasions, such as last August 2013 when intense to torrential rains brought about by the enhanced Southwest Monsoon caused massive flooding in Metro Manila. Coupled with observations from Doppler imagery and water level sensors along the Marikina River, the local officials used this information and determined that the river would overflow in a few hours. It gave them a critical lead time to evacuate residents along the floodplain and no casualties were reported after the event.

Differential Diagnosis and Treatment of Impaired Bladder Emptying

PubMed Central

Yoshimura, Naoki; Chancellor, Michael B

2004-01-01

Although much attention is paid to urinary incontinence, the condition of incomplete bladder emptying is becoming more common with the aging of the US population and the widespread use of anticholinergic drugs to treat overactive bladder. This disorder can often be silent until end-stage presentation of overflow incontinence. In this article, we review the pathophysiologic conditions of the bladder and urethra that can cause impaired bladder emptying and discuss how to evaluate and screen the patient with a bladder that does not empty. In addition, we provide an overview of treatment options available for impaired bladder emptying and consider the research that is under way to find the best therapies for the failing bladder. PMID:16985851

Recent Developments in OVERGRID, OVERFLOW-2 and Chimera Grid Tools Scripts

NASA Technical Reports Server (NTRS)

Chan, William M.

2004-01-01

OVERGRID and OVERFLOW-2 feature easy to use multiple-body dynamics. The new features of OVERGRID include a preliminary chemistry interface, standard atmosphere and mass properties calculators, a simple unsteady solution viewer, and a debris tracking interface. Script library development in Chimera Grid Tools has applications in turbopump grid generation. This viewgraph presentation profiles multiple component dynamics, validation test cases for a sphere, cylinder, and oscillating airfoil, and debris analysis.

An Investigation into the Nature of Non-Voiding Contractions Resulting from Detrusor Hyperreflexia in Neurogenic Bladders Following Spinal Cord Injury

DTIC Science & Technology

2013-10-01

voiding contractions (NVC) during normal bladder filling. These NVC are responsible for incontinence episodes, bladder and bladder neck damage, as...eliminated, however, voiding occurred by a combination of augmented overflow incontinence (NVC-driven and a vesicosomatic reflex of the hindquarters...spinal micturition reflex, but rather an augmented overflow incontinence with a locomotor component (High amplitude pressure swings in bottom trace

A Pre-Emptive Horizontal Channel Borrowing and Vertical Traffic Overflowing Channel Allocation Scheme for Overlay Networks

NASA Astrophysics Data System (ADS)

Zhao, Fang-Ming; Jiang, Ling-Ge; He, Chen

In this paper, a channel allocation scheme is studied for overlay wireless networks to optimize connection-level QoS. The contributions of our work are threefold. First, a channel allocation strategy using both horizontal channel borrowing and vertical traffic overflowing (HCBVTO) is presented and analyzed. When all the channels in a given macrocell are used, high-mobility real-time handoff requests can borrow channels from adjacent homogeneous cells. In case that the borrowing requests fail, handoff requests may also be overflowed to heterogeneous cells, if possible. Second, high-mobility real-time service is prioritized by allowing it to preempt channels currently used by other services. And third, to meet the high QoS requirements of some services and increase the utilization of radio resources, certain services can be transformed between real-time services and non-real-time services as necessary. Simulation results demonstrate that the proposed schemes can improve system performance.

Wafer-level Cu-Sn micro-joints with high mechanical strength and low Sn overflow

NASA Astrophysics Data System (ADS)

Duan, Ani; Luu, Thi-Thuy; Wang, Kaiying; Aasmundtveit, Knut; Hoivik, Nils

2015-09-01

In this paper, we report wafer-level bonding using solid-liquid inter-diffusion (SLID) processes for fabricating micro-joints Cu-Sn at low temperature (270 °C). The evolution of multilayer Cu/Sn to micro-joint alloys has been characterized by optical microscopy and mechanical die-shear testing. The Cu-Sn joints with line width from 80 to 200 μm prove to be reliable packaging materials for bonding vacuum micro-cavities with controllable Sn overflow, as well as high mechanical strength (>70 MPa). A thermodynamic model has been performed to further understand the formation of Cu-Sn intermetallic alloys. There are two important findings for this work: 1) Using a two-step temperature profile may significantly reduce the amount of Sn overflow; 2) for packaging, a bond frame width greater than 80 μm will result in high yield.

Efficiency of a turbidity-based, real-time control strategy applied to a retention tank: a simulation study.

PubMed

Lacour, C; Joannis, C; Schuetze, M; Chebbo, G

2011-01-01

This paper compares several real-time control (RTC) strategies for a generic configuration consisting of a storage tank with two overflow facilities. Two of the strategies only make use of flow rate data, while the third also introduces turbidity data in order to exercise dynamic control between two overflow locations. The efficiency of each strategy is compared over a wide range of system setups, described by two parameters. This assessment is performed by simulating the application of control strategies to actual measurements time series recorded on two sites. Adding turbidity measurements into an RTC strategy leads to a significant reduction in the annual overflow pollutant load. The pollutant spills spared by such a control strategy strongly depend on the site and on the flow rate based strategy considered as a reference. With the datasets used in this study, values ranging from 5 to 50% were obtained.

On buffer overflow duration in a finite-capacity queueing system with multiple vacation policy

NASA Astrophysics Data System (ADS)

Kempa, Wojciech M.

2017-12-01

A finite-buffer queueing system with Poisson arrivals and generally distributed processing times, operating under multiple vacation policy, is considered. Each time when the system becomes empty, the service station takes successive independent and identically distributed vacation periods, until, at the completion epoch of one of them, at least one job waiting for service is detected in the buffer. Applying analytical approach based on the idea of embedded Markov chain, integral equations and linear algebra, the compact-form representation for the cumulative distribution function (CDF for short) of the first buffer overflow duration is found. Hence, the formula for the CDF of next such periods is obtained. Moreover, probability distributions of the number of job losses in successive buffer overflow periods are found. The considered queueing system can be efficienly applied in modelling energy saving mechanisms in wireless network communication.

[Study on the characteristics of combined sewer overflow from the high density residential area in Shanghai].

PubMed

Li, He; Li, Tian

2006-08-01

The urban non-point pollution has become main pollution resource of urban water bodies of Shanghai. Character of combined sewer overflow from watershed SA in Shanghai was studied, and the correlation of influence factors to the EMCs of overflows was discussed. It is found that the EMCs of COD, BOD, SS, NH3-N, TN, TP are 614 mg/L, 208.5 mg/L, 684 mg/L, 17.6 mg/L, 29.8 mg/L, 3.0 mg/L respectively, and the values obtained herein are much higher than the documented data from other countries. From the probability plot of the EMCs, it is found that the BOD has the best fitness for lognormal distribution; and correlation between the EMCs of COD, SS and the ratio of antecedent dry weather time to rain duration is quite good.

Human brain somatostatin release from isolated cortical nerve endings and its modulation through GABAB receptors.

PubMed Central

Bonanno, G.; Gemignani, A.; Schmid, G.; Severi, P.; Cavazzani, P.; Raiteri, M.

1996-01-01

1. The release of somatostatin-like immunoreactivity (SRIF-LI) in the human brain was studied in synaptosomal preparations from fresh neocortical specimens obtained from patients undergoing neurosurgery to remove deeply sited tumours. 2. The basal outflow of SRIF-LI from superfused synaptosomes was increased about 3 fold during exposure to a depolarizing medium containing 15 mM KCl. The K(+)-evoked overflow of SRIF-LI was almost totally dependent on the presence of Ca2+ in the superfusion medium. 3. The GABAB receptor agonist, (-)-baclofen (0.3 - 100 microM), inhibited the overflow of SRIF-LI in a concentration-dependent manner (EC50 = 1.84 +/- 0.20 microM; maximal effect: about 50%). The novel GABAB receptor ligand, 3-aminopropyl(difluoromethyl)phosphinic acid (CGP 47656) mimicked (-)-baclofen in inhibiting the SRIF-LI overflow (EC50 = 3.06 +/- 0.52 microM; maximal effect: about 50%), whereas the GABAA receptor agonist, muscimol, was ineffective up to 100 microM. 4. The inhibition by 10 microM (-)-baclofen of the K(+)-evoked SRIF-LI overflow was concentration-dependently prevented by two selective GABAB receptor antagonists, 3-amino-propyl (diethoxymethyl)-phosphinic acid (CGP 35348) (IC50 = 24.40 +/- 2.52 microM) and [3-[[(3,4-dichlorophenyl) methyl]amino]propyl] (diethoxymethyl) phosphinic acid (CGP 52432) (IC50 = 0.06 +/- 0.005 microM). 5. The inhibition of SRIF-LI overflow caused by 10 microM CGP 47656 was abolished by 1 microM CGP 52432. 6. When human synaptosomes were labelled with [3H]-GABA and depolarized in superfusion with 15 mM KCl, the inhibition by 10 microM (-)-baclofen of the depolarization-evoked [3H]-GABA overflow was largely prevented by 10 microM CGP 47656 which therefore behaved as an autoreceptor antagonist. 7. In conclusion: (a) the characteristics of SRIF-LI release from synaptosomal preparations of human neocortex are compatible with a neuronal origin; (b) the nerve terminals releasing the neuropeptide possess inhibitory receptors of the GABAB type; (c) these receptors differ pharmacologically from the GABAB autoreceptors present on human neocortex nerve terminals since the latter have been shown to be CGP 35348-insensitive but can be blocked by CGP 47656. PMID:8832070

The Impact of Biochar on Bioretention Nitrogen Removal and Hydrologic Performance

NASA Astrophysics Data System (ADS)

Tian, J.; Jin, J.; Chiu, P.; Guo, M.; Imhoff, P. T.

2016-12-01

Poor nitrate removal and substantial land occupation are two factors that limit the application of bioretention facilities. Biochar was evaluated in this study as an amendment of bioretention media to enhance nitrogen removal from runoff as well as improve hydrologic performance. Two pilot-scale bioretention cells (91 cm dia., 1.2 m deep) were constructed in parallel, and both contained 20 cm saturation zone with coarse sand, 76 cm vadose zone with treatment medium, and 5 cm of triple-shredded wood mulch from bottom to top. Treatment medium in the control cell was a mixture of 88% sand, 8% clay, and 4% sawdust by mass, while the biochar cell amended 4% commercial biochar pyrolyzed from Southern Yellow Pine at 550°. Both cells were instrumented with soil moisture sensors, soil potential sensors and temperature sensors. A field infiltration test was conducted in each cell using a tension disc infiltrometer directly on the treatment media to obtain soil hydraulic parameters, then three 24-36-hour tracer tests containing bromide and nitrate pollutant were conducted over a five-month period. Influent, effluent and pore water were continuously sampled for bromide and nitrogen analysis during these tests. In addition, hydrologic performance of the two cells under various conditions of rainfall recurrence interval and duration were simulated using HYDRUS-1D after verification with tracer test data. Results showed that the biochar cell reduced NO3-N concentrations by 30.6-84.7%, while the control cell only reduced NO3-N by -6-43.5%, depending on the storm. Biochar amendment slightly increased the average pH of the vadose zone from 6.3 to 7.3, decreased the average dissolve oxygen content by 43%, and decreased the average oxidation-reduction potential from 22 mV to -115 mV, which contributed to the enhanced nitrate removal. Biochar-amended medium increased saturated hydraulic conductivity by 1.5 times, and increased cell residence time and water retention by 12.6% and 15% respectively during the tracer tests. For a 1-yr interval and 24-hr duration storm simulation, the biochar-amended cell could reduce overflow by 78%, extend the delay of the peak flow by two times and decrease the peak outflow rate by 35%, compared to the control cell.

Physical modeling of transverse drainage mechanisms

NASA Astrophysics Data System (ADS)

Douglass, J. C.; Schmeeckle, M. W.

2005-12-01

Streams that incise across bedrock highlands such as anticlines, upwarps, cuestas, or horsts are termed transverse drainages. Their relevance today involves such diverse matters as highway and dam construction decisions, location of wildlife corridors, better-informed sediment budgets, and detailed studies into developmental histories of late Cenozoic landscapes. The transient conditions responsible for transverse drainage incision have been extensively studied on a case-by-case basis, and the dominate mechanisms proposed include: antecedence, superimposition, overflow, and piracy. Modeling efforts have been limited to antecedence, and such the specific erosional conditions required for transverse drainage incision, with respect to the individual mechanisms, remains poorly understood. In this study, fifteen experiments attempted to simulate the four mechanisms and constructed on a 9.15 m long, 2.1 m wide, and 0.45 m deep stream table. Experiments lasted between 50 and 220 minutes. The stream table was filled with seven tons of sediment consisting of a silt and clay (30%) and a fine to coarse sand (70%) mixture. The physical models highlighted the importance of downstream aggradation with regard to antecedent incision versus possible defeat and diversion. The overflow experiments indicate that retreating knickpoints across a basin outlet produce a high probability of downstream flooding when associated with a deep lake. Misters used in a couple of experiments illustrate a potential complication with regard to headward erosion driven piracy. Relatively level asymmetrically sloped ridges allow for the drainage divide across the ridge to retreat from headward erosion, but hindered when the ridge's apex undulates or when symmetrically sloped. Although these physical models cannot strictly simulate natural transverse drainages, the observed processes, their development over time, and resultant landforms roughly emulate their natural counterparts. Proposed originally from an extensive literature search, most of the criteria that indicate the expected evidence associated with each mechanism following transverse drainage incision were replicated for antecedence, overflow, and piracy. Two superimposition experiments failed to replicate the mechanism and test the associated criteria. Following experimentation, the criteria were applied in a cursory fashion to twenty randomly selected sites in the southwestern USA. Development of first order hypotheses were ranked on a confidence scale tied to individual criterion noted in the field, literature, and DEMs for each site. The results indicate a possible link between the dominant tectonic regime and the proposed mechanisms; and highlight the importance of short-lived fluvial instabilities in relation to understanding long-term drainage development.

Hole transport in c-plane InGaN-based green laser diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Yang; Liu, Jianping, E-mail: jpliu2010@sinano.ac.cn; Tian, Aiqin

2016-08-29

Hole transport in c-plane InGaN-based green laser diodes (LDs) has been investigated by both simulations and experiments. It is found that holes can overflow from the green double quantum wells (DQWs) at high current density, which reduces carrier injection efficiency of c-plane InGaN-based green LDs. A heavily silicon-doped layer right below the green DQWs can effectively suppress hole overflow from the green DQWs.

Modelling total suspended solids, E. coli and carbamazepine, a tracer of wastewater contamination from combined sewer overflows

NASA Astrophysics Data System (ADS)

Pongmala, Khemngeun; Autixier, Laurène; Madoux-Humery, Anne-Sophie; Fuamba, Musandji; Galarneau, Martine; Sauvé, Sébastien; Prévost, Michèle; Dorner, Sarah

2015-12-01

Urban source water protection requires knowledge of sources of fecal contamination upstream of drinking water intakes. Combined and sanitary sewer overflows (CSOs and SSOs) are primary sources of microbiological contamination and wastewater micropollutants (WWMPs) in urban water supplies. To quantify the impact of sewer overflows, predictive simulation models are required and have not been widely applied for microbial contaminants such as fecal indicator bacteria and pathogens in urban drainage networks. The objective of this study was to apply a simulation model to estimate the dynamics of three contaminants in sewer overflows - total suspended solids, Escherichia coli (E. coli) and carbamazepine, a WWMP. A mixed combined and pseudo-sanitary drainage network in Québec, Canada was studied and modelled for a total of 7 events for which water quality data were available. Model results were significantly correlated with field water quality data. The model confirmed that the contributions of E. coli from runoff and sewer deposits were minor and their dominant source was from sewage. In contrast, the main sources of total suspended solids were stormwater runoff and sewer resuspension. Given that it is not present in stormwater, carbamazepine was found to be a useful stable tracer of sewage contributions to total contaminant loads and also provided an indication of the fraction of total suspended solids originating from sewer deposits because of its similar response to increasing flowrates.

Generally applicable fed-batch culture concept based on the detection of metabolic state by on-line balancing.

PubMed

Jobé, Anna Marya; Herwig, Christoph; Surzyn, Martin; Walker, Bernhard; Marison, Ian; von Stockar, Urs

2003-06-20

In many microorganisms, flux limitations in oxidative metabolism lead to the formation of overflow metabolites even under fully aerobic conditions. This can be avoided if the specific growth rate is controlled at a low enough value. This is usually accomplished by controlling the substrate feeding profile in a fed-batch process. The present work proposes a control concept which is based on the on-line detection of metabolic state by on-line calculation of mass and elemental balances. The advantages of this method are: 1) the check of measurement consistency based on all of the available measurements, 2) the minimum requirement of a priori knowledge of metabolism, and 3) the exclusive use of simple and established on-line techniques which do not require direct measurement of the metabolite in question. The control concept has been linked to a simple adaptive controller and applied to fed-batch cultures of S. cerevisiae and E. coli, organisms which express different overflow metabolites, ethanol and acetic acid, respectively. Oxidative and oxidoreductive states of S. cerevisiae and E. coli cultures were detected with high precision. As demonstrated by the formation of acetic acid in E. coli cultures, metabolic states could be correctly distinguished for systems for which traditional methods, such as respiratory quotient (RQ), are insensitive. Hence, it could be shown that the control concept allowed avoidance of overflow metabolite formation and operation at maximum oxidative biomass productivity and oxidative conversion of substrate into biomass. Based on mass and elemental balances, the proposed method additionally provides a richness of additional information, such as yield coefficients and estimation of concentrations and specific conversion rates. These data certainly help the operator to additionally evaluate the state of the process on-line. Copyright 2003 Wiley Periodicals, Inc. Biotechnol Bioeng 82: 627-639, 2003.

Evaluating rain gardens as a method to reduce the impact of sewer overflows in sources of drinking water.

PubMed

Autixier, Laurène; Mailhot, Alain; Bolduc, Samuel; Madoux-Humery, Anne-Sophie; Galarneau, Martine; Prévost, Michèle; Dorner, Sarah

2014-11-15

The implications of climate change and changing precipitation patterns need to be investigated to evaluate mitigation measures for source water protection. Potential solutions need first to be evaluated under present climate conditions to determine their utility as climate change adaptation strategies. An urban drainage network receiving both stormwater and wastewater was studied to evaluate potential solutions to reduce the impact of combined sewer overflows (CSOs) in a drinking water source. A detailed hydraulic model was applied to the drainage basin to model the implementation of best management practices at a drainage basin scale. The model was calibrated and validated with field data of CSO flows for seven events from a survey conducted in 2009 and 2010. Rain gardens were evaluated for their reduction of volumes of water entering the drainage network and of CSOs. Scenarios with different levels of implementation were considered and evaluated. Of the total impervious area within the basin directly connected to the sewer system, a maximum of 21% could be alternately directed towards rain gardens. The runoff reductions for the entire catchment ranged from 12.7% to 19.4% depending on the event considered. The maximum discharged volume reduction ranged from 13% to 62% and the maximum peak flow rate reduction ranged from 7% to 56%. Of concern is that in-sewer sediment resuspension is an important process to consider with regard to the efficacy of best management practices aimed at reducing extreme loads and concentrations. Rain gardens were less effective for large events, which are of greater importance for drinking water sources. These practices could increase peak instantaneous loads as a result of greater in-sewer resuspension during large events. Multiple interventions would be required to achieve the objectives of reducing the number, total volumes and peak contaminant loads of overflows upstream of drinking water intakes. Copyright © 2014 Elsevier B.V. All rights reserved.

Performance of the OVERFLOW-MLP and LAURA-MLP CFD Codes on the NASA Ames 512 CPU Origin System

NASA Technical Reports Server (NTRS)

Taft, James R.

2000-01-01

The shared memory Multi-Level Parallelism (MLP) technique, developed last year at NASA Ames has been very successful in dramatically improving the performance of important NASA CFD codes. This new and very simple parallel programming technique was first inserted into the OVERFLOW production CFD code in FY 1998. The OVERFLOW-MLP code's parallel performance scaled linearly to 256 CPUs on the NASA Ames 256 CPU Origin 2000 system (steger). Overall performance exceeded 20.1 GFLOP/s, or about 4.5x the performance of a dedicated 16 CPU C90 system. All of this was achieved without any major modification to the original vector based code. The OVERFLOW-MLP code is now in production on the inhouse Origin systems as well as being used offsite at commercial aerospace companies. Partially as a result of this work, NASA Ames has purchased a new 512 CPU Origin 2000 system to further test the limits of parallel performance for NASA codes of interest. This paper presents the performance obtained from the latest optimization efforts on this machine for the LAURA-MLP and OVERFLOW-MLP codes. The Langley Aerothermodynamics Upwind Relaxation Algorithm (LAURA) code is a key simulation tool in the development of the next generation shuttle, interplanetary reentry vehicles, and nearly all "X" plane development. This code sustains about 4-5 GFLOP/s on a dedicated 16 CPU C90. At this rate, expected workloads would require over 100 C90 CPU years of computing over the next few calendar years. It is not feasible to expect that this would be affordable or available to the user community. Dramatic performance gains on cheaper systems are needed. This code is expected to be perhaps the largest consumer of NASA Ames compute cycles per run in the coming year.The OVERFLOW CFD code is extensively used in the government and commercial aerospace communities to evaluate new aircraft designs. It is one of the largest consumers of NASA supercomputing cycles and large simulations of highly resolved full aircraft are routinely undertaken. Typical large problems might require 100s of Cray C90 CPU hours to complete. The dramatic performance gains with the 256 CPU steger system are exciting. Obtaining results in hours instead of months is revolutionizing the way in which aircraft manufacturers are looking at future aircraft simulation work. Figure 2 below is a current state of the art plot of OVERFLOW-MLP performance on the 512 CPU Lomax system. As can be seen, the chart indicates that OVERFLOW-MLP continues to scale linearly with CPU count up to 512 CPUs on a large 35 million point full aircraft RANS simulation. At this point performance is such that a fully converged simulation of 2500 time steps is completed in less than 2 hours of elapsed time. Further work over the next few weeks will improve the performance of this code even further.The LAURA code has been converted to the MLP format as well. This code is currently being optimized for the 512 CPU system. Performance statistics indicate that the goal of 100 GFLOP/s will be achieved by year's end. This amounts to 20x the 16 CPU C90 result and strongly demonstrates the viability of the new parallel systems rapidly solving very large simulations in a production environment.

Purinoceptor modulation of noradrenaline release in rat tail artery: tonic modulation mediated by inhibitory P2Y- and facilitatory A2A-purinoceptors.

PubMed Central

Gonçalves, J.; Queiroz, G.

1996-01-01

1. The effects of analogues of adenosine and ATP on noradrenaline release elicited by electrical stimulation (5 Hz, 2700 pulses) were studied in superfused preparations of rat tail artery. The effects of purinoceptor antagonists, of adenosine deaminase and of adenosine uptake blockade were also examined. Noradrenaline was measured by h.p.l.c. electrochemical detection. 2. The A1-adenosine receptor agonist, N6-cyclopentyladenosine (CPA; 0.1-100 nM) reduced, whereas the A2A-receptor agonist 2-p-(2-carboxyethyl)phenethylamino-5'-N-ethylcarboxamidoadenosine (CGS 21680; 3-30 nM) increased evoked noradrenaline overflow. These effects were antagonized by the A1-adenosine receptor antagonist, 8-cyclopentyl-1,3-dipropylxanthine (DPCPX; 20 nM) and the A2-adenosine receptor antagonist, 3,7-dimethyl-1-propargylxanthine (DMPX; 100 nM), respectively. The P2Y-purinoceptor agonist, 2-methylthio-ATP (1-100 microM) reduced noradrenaline overflow, an effect prevented by the P2-purinoceptor antagonist, cibacron blue 3GA (100 microM) and suramin (100 microM). 3. Adenosine deaminase (2 u ml-1), DMPX (100 nM) and inhibition of adenosine uptake with S-(p-nitrobenzyl)-6-thioinosine (NBTI; 50 nM) decreased evoked noradrenaline overflow. DPCPX alone did not change noradrenaline overflow but prevented the inhibition caused by NBTI. The P2Y-purinoceptor antagonist, cibacron blue 3GA (100 microM) increased evoked noradrenaline overflow as did suramin, a non-selective P2-antagonist. 4. It is concluded that, in rat tail artery, inhibitory (A1 and P2Y) and facilitatory (A2A) purinoceptors are present and modulate noradrenaline release evoked by electrical stimulation. Endogenous purines tonically modulate noradrenaline release through activation of inhibitory P2Y and facilitatory A2A purinoceptors, whereas a tonic activation of inhibitory A1 purinoceptors seems to be prevented by adenosine uptake. PMID:8825357

A vision-based tool for the control of hydraulic structures in sewer systems

NASA Astrophysics Data System (ADS)

Nguyen, L.; Sage, D.; Kayal, S.; Jeanbourquin, D.; Rossi, L.

2009-04-01

During rain events, the total amount of the wastewater/storm-water mixture cannot be treated in the wastewater treatment plant; the overflowed water goes directly into the environment (lakes, rivers, streams) via devices called combined sewers overflows (CSOs). This water is untreated and is recognized as an important source of pollution. In most cases, the quantity of overflowed water is unknown due to high hydraulic turbulences during rain events; this quantity is often significant. For this reason, the monitoring of the water flow and the water level is of crucial environmental importance. Robust monitoring of sewer systems is a challenging task to achieve. Indeed, the environment inside sewers systems is inherently harsh and hostile: constant humidity of 100%, fast and large water level changes, corrosive atmosphere, presence of gas, difficult access, solid debris inside the flow. A flow monitoring based on traditional probes placed inside the water (such as Doppler flow meter) is difficult to conduct because of the solid material transported by the flow. Probes placed outside the flow such as ultrasonic water level probes are often used; however the measurement is generally done on only one particular point. Experience has shown that the water level in CSOs during rain events is far from being constant due to hydraulic turbulences. Thus, such probes output uncertain information. Moreover, a check of the data reliability is impossible to achieve. The HydroPix system proposes a novel approach to the monitoring of sewers based on video images, without contact with the water flow. The goal of this system is to provide a monitoring tool for wastewater system managers (end-users). The hardware was chosen in order to suit the harsh conditions of sewers system: Cameras are 100% waterproof and corrosion-resistant; Infra-red LED illumination systems are used (waterproof, low power consumption); A waterproof case contains the registration and communication system. The monitoring software has the following requirements: visual analysis of particular hydraulic behavior, automatic vision-based flow measurements, automatic alarm system for particular events (overflows, risk of flooding, etc), database for data management (images, events, measurements, etc.), ability to be controlled remotely. The software is implemented in modular server/client architecture under LabVIEW development system. We have conducted conclusive in situ tests in various sewers configurations (CSOs, storm-water sewerage, WWTP); they have shown the ability of the HydroPix to perform accurate monitoring of hydraulic structures. Visual information demonstrated a better understanding of the flow behavior in complex and difficult environment.

Effects of extreme rainfall events on the distribution of selected emerging contaminants in surface and groundwater: The Guadalete River basin (SW, Spain).

PubMed

Corada-Fernández, Carmen; Candela, Lucila; Torres-Fuentes, Nivis; Pintado-Herrera, Marina G; Paniw, Maria; González-Mazo, Eduardo

2017-12-15

This study is focused on the Guadalete River basin (SW, Spain), where extreme weather conditions have become common, with and alternation between periods of drought and extreme rainfall events. Combined sewer overflows (CSOs) occur when heavy rainfall events exceed the capacity of the wastewater treatment plants (WWTP), as well as pollution episodes in parts of the basin due to uncontrolled sewage spills and the use of reclaimed water and sludge from the local WWTP. The sampling was carried out along two seasons and three campaigns during dry (March 2007) and extreme rainfall (April and December 2010) in the Guadalete River, alluvial aquifer and Jerez de la Frontera aquifer. Results showed minimum concentrations for synthetic surfactants in groundwater (<37.4μg·L -1 ) during the first campaign (dry weather conditions), whereas groundwater contaminants increased in December 2010 as the heavy rainfall caused the river to overflow. In surface water, surfactant concentrations showed similar trends to groundwater observations. In addition to surfactants, pharmaceuticals and personal care products (PPCPs) were analyzed in the third campaign, 22 of which were detected in surface waters. Two fragrances (OTNE and galaxolide) and one analgesic/anti-inflammatory (ibuprofen) were the most abundant PPCPs (up to 6540, 2748 and 1747ng·L -1 , respectively). Regarding groundwater, most PPCPs were detected in Jerez de la Frontera aquifer, where a synthetic fragrance (OTNE) was predominant (up to 1285ng·L -1 ). Copyright © 2017 Elsevier B.V. All rights reserved.

Exposure to conditions of uncertainty promotes the pursuit of amphetamine.

PubMed

Mascia, Paola; Neugebauer, Nichole M; Brown, Jason; Bubula, Nancy; Nesbitt, Kathryn M; Kennedy, Robert T; Vezina, Paul

2018-05-22

Prior exposure to abused drugs leads to long-lasting neuroadaptations culminating in excessive drug intake. Given the comorbidity between substance use and gambling disorders, surprisingly little is known about the effects of exposure to reinforcement contingencies experienced during games of chance. As it is a central feature of these games, we characterized the effects of exposure to uncertainty on biochemical and behavioral effects normally observed in rats exposed to amphetamine. Rats in different groups were trained to nose-poke for saccharin under certain [fixed-ratio (FR)] or uncertain conditions [variable-ratio (VR)] for 55 1-h sessions. Ratios were escalated on successive sessions and rats maintained on the last ratio (FR/VR 20) for 20-25 days. Two to three weeks later, rats were tested for their locomotor or nucleus accumbens dopamine (NAcc DA) response to amphetamine or self-administration of the drug using a lever press operant. NAcc DA overflow was also assessed in additional rats during the saccharin sessions. Rats exposed to uncertainty subsequently showed a higher locomotor and NAcc DA response to amphetamine and self-administered more drug infusions relative to rats exposed to predictable reinforcement. NAcc DA levels during the saccharin sessions tracked the variance of the scheduled ratios (a measure of uncertainty). VR rats showed escalating DA overflow with increasing ratios. Exposure to uncertainty triggered neuroadaptations similar to those produced by exposure to abused drugs. As these were produced in drug naive rats both during and after exposure to uncertainty, they provide a novel common pathway to drug and behavioral addictions.

Real-Time Distributed Embedded Oscillator Operating Frequency Monitoring

NASA Technical Reports Server (NTRS)

Pollock, Julie; Oliver, Brett; Brickner, Christopher

2012-01-01

A document discusses the utilization of embedded clocks inside of operating network data links as an auxiliary clock source to satisfy local oscillator monitoring requirements. Modem network interfaces, typically serial network links, often contain embedded clocking information of very tight precision to recover data from the link. This embedded clocking data can be utilized by the receiving device to monitor the local oscillator for tolerance to required specifications, often important in high-integrity fault-tolerant applications. A device can utilize a received embedded clock to determine if the local or the remote device is out of tolerance by using a single link. The local device can determine if it is failing, assuming a single fault model, with two or more active links. Network fabric components, containing many operational links, can potentially determine faulty remote or local devices in the presence of multiple faults. Two methods of implementation are described. In one method, a recovered clock can be directly used to monitor the local clock as a direct replacement of an external local oscillator. This scheme is consistent with a general clock monitoring function whereby clock sources are clocking two counters and compared over a fixed interval of time. In another method, overflow/underflow conditions can be used to detect clock relationships for monitoring. These network interfaces often provide clock compensation circuitry to allow data to be transferred from the received (network) clock domain to the internal clock domain. This circuit could be modified to detect overflow/underflow conditions of the buffering required and report a fast or slow receive clock, respectively.

Levels of Antioxidant Activity and Fluoride Content in Coffee Infusions of Arabica, Robusta and Green Coffee Beans in According to their Brewing Methods.

PubMed

Wolska, J; Janda, Katarzyna; Jakubczyk, K; Szymkowiak, M; Chlubek, D; Gutowska, I

2017-10-01

Coffee is a rich source of dietary antioxidants, and this property links with the fact that coffee is one of the world's most popular beverages. Moreover, it is a source of macro- and microelements, including fluoride. The aim of this work was to determine antioxidant activity of coffee beverages and fluoride content depending on different coffee species and conditions of brewing. Three species of coffee, arabica, robusta and green coffee beans obtained from retail stores in Szczecin (Poland) were analyzed. Five different techniques of preparing drink were used: simple infusion, french press, espresso maker, overflow espresso and Turkish coffee. Antioxidant potential of coffee beverages was investigated spectrophotometrically by DPPH method. Fluoride concentrations were measured by potentiometric method with a fluoride ion-selective electrode. Statistical analysis was performed using Stat Soft Statistica 12.5. Antioxidant activity of infusions was high (71.97-83.21% inhibition of DPPH) depending on coffee species and beverage preparing method. It has been shown that the method of brewing arabica coffee and green coffee significantly affects the antioxidant potential of infusions. The fluoride concentration in the coffee infusions changed depending, both, on the species and conditions of brewing, too (0.013-0.502 mg/L). Methods of brewing didn't make a difference to the antioxidant potential of robusta coffee, which had also the lowest level of fluoride among studied species. Except overflow espresso, the fluoride content was the highest in beverages from green coffee. The highest fluoride content was found in Turkish coffee from green coffee beans.

Data Collision Prevention with Overflow Hashing Technique in Closed Hash Searching Process

NASA Astrophysics Data System (ADS)

Rahim, Robbi; Nurjamiyah; Rafika Dewi, Arie

2017-12-01

Hash search is a method that can be used for various search processes such as search engines, sorting, machine learning, neural network and so on, in the search process the possibility of collision data can happen and to prevent the occurrence of collision can be done in several ways one of them is to use Overflow technique, the use of this technique perform with varying length of data and this technique can prevent the occurrence of data collisions.

Rapidly solidified titanium alloys by melt overflow

NASA Technical Reports Server (NTRS)

Gaspar, Thomas A.; Bruce, Thomas J., Jr.; Hackman, Lloyd E.; Brasmer, Susan E.; Dantzig, Jonathan A.; Baeslack, William A., III

1989-01-01

A pilot plant scale furnace was designed and constructed for casting titanium alloy strips. The furnace combines plasma arc skull melting techniques with melt overflow rapid solidification technology. A mathematical model of the melting and casting process was developed. The furnace cast strip of a suitable length and width for use with honeycomb structures. Titanium alloys Ti-6Al-4V and Ti-14Al-21 Nb were successfully cast into strips. The strips were evaluated by optical metallography, microhardness measurements, chemical analysis, and cold rolling.

Dynamics of rain-induced pollutographs of solubles in sewers.

PubMed

Rutsch, M; Müller, I; Krebs, P

2005-01-01

When looking at acute receiving water impacts due to combined sewer overflows the characteristics of the background diurnal sewage flux variation may influence the peak loads from combined sewer overflows (CSO) and wastewater treatment plant (WWTP) effluent significantly. In this paper, effects on the dynamic compounds transported in the sewer, on CSO discharges and WWTP loading are evaluated by means of hydrodynamic simulations. The simulations are based on different scenarios for diurnal dry-weather flow variations induced by different infiltration rates.

Developing and Evaluating Prototype of Waste Volume Monitoring Using Internet of Things

NASA Astrophysics Data System (ADS)

Fathhan Arief, Mohamad; Lumban Gaol, Ford

2017-06-01

In Indonesia, especially Jakarta have a lot of garbage strewn that can be an eyesore and also cause pollution that can carry diseases. Garbage strewn can cause many things, one of her dues is bins are overflowing due to the full so it can not accommodate the waste dumped from other people. Thus, the author created a new method for waste disposal more systematic. In creating new method requires a technology to supports, then the author makes a prototype for waste volume monitoring. By using the internet of things prototype of waste volume monitoring may give notification to the sanitary agency that waste in the trash bin needs to be disposal. In this study, conducted the design and manufactured of prototype waste volume monitoring using LinkItONE board based by Arduino and an ultrasonic sensor for appliance senses. Once the prototype is completed, evaluation in order to determine whether the prototype will function properly. The result showed that the expected function of a prototype waste volume monitoring can work well.

Priority substances in combined sewer overflows: case study of the Paris sewer network.

PubMed

Gasperi, J; Garnaud, S; Rocher, V; Moilleron, R

2011-01-01

This study was undertaken to supply data on both priority pollutant (PP) occurrence and concentrations in combined sewer overflows (CSOs). A single rain event was studied on 13 sites within the Paris sewer network. For each sample, a total of 66 substances, including metals, polycyclic aromatic hydrocarbons (PAHs), pesticides, organotins, volatile organic compounds, chlorobenzenes, phthalates and alkylphenols were analyzed. Of the 66 compounds analyzed in all, 40 PPs including 12 priority hazardous substances were detected in CSOs. As expected, most metals were present in all samples, reflecting their ubiquitous nature. Chlorobenzenes and most pesticides were never quantified above the limit of quantification, while the majority of the other organic pollutants, except DEHP (median concentration: 22 μg.l(-1)), were found to lie in the μg.l(-1) range. For the particular rain event studied, the pollutant loads discharged by CSOs were evaluated and then compared to pollutant loads conveyed by the Seine River. Under the hydraulic conditions considered and according to the estimations performed, this comparison suggests that CSOs are potentially significant local source of metals, PAHs and DEHP. Depending on the substance, the ratio between the CSO and Seine River loads varied from 0.5 to 26, underscoring the important local impact of CSOs at the scale of this storm for most pollutants.

Hydraulic modeling of flow impact on bridge structures: a case study on Citarum bridge

NASA Astrophysics Data System (ADS)

Siregar, R. I.

2018-02-01

Flood waves because of the rapid catchment response to high intense rainfall, breaches of flood defenses may induce huge impact forces on structures, causing structural damage or even failures. Overflowing stream that passes over the bridge, it means to discharge flood water level is smaller than the capacity of the river flow. In this study, the researches present the methodological approach of flood modeling on bridge structures. The amount of force that obtained because of the hydrostatic pressure received by the bridge at the time of the flood caused the bridge structure disrupted. This paper presents simulation of flow impact on bridge structures with some event flood conditions. Estimating the hydrostatic pressure developed new model components, to quantify the flow impact on structures. Flow parameters applied the model for analyzing, such as discharge, velocity, and water level or head that effect of bridge structures. The simulation will illustrate the capability of bridge structures with some event flood river and observe the behavior of the flow that occurred during the flood. Hydraulic flood modeling use HEC-RAS for simulation. This modeling will describe the impact on bridge structures. Based on the above modelling resulted, in 2008 has flood effect more than other years on the Citarum Bridge, because its flow overflow on the bridge.

Combined Sewer Overflows as a Source of Hormones to Surface Water

NASA Astrophysics Data System (ADS)

Phillips, P.; Chalmers, A.; Gray, J. L.; Foreman, W.; Kolpin, D. W.; Wall, G.; Esposito, K.

2009-12-01

Some sources of hormones to surface water, such as wastewater-treatment-plant (WWTP) effluent, have been well documented, but other sources, particularly wet-weather discharges from combined-sewer-overflows (CSOs), are not well characterized. Flow-weighted composite samples of secondarily treated WWTP effluent and untreated sewage discharges from WWTP inflows and CSO discharges were collected during 12 storms and 6 non-storm conditions from November 2007-December 2008 at the main Burlington Vermont WWTP. Concentrations of many androgens and estrogens were highest in samples from untreated sewage, and lower in samples from treated sewage. For example, concentrations of estriol in CSO samples ranged from 5 to over 100 ng/L (nanograms per liter), but were generally less than 1 ng/L in treated sewage. Many androgens were detected in CSO discharge samples in concentrations ranging from 1 to over 1000 ng/L, but were not detected above 1 ng/L in treated samples. For many of the hormones, including androgens and estriol, CSO discharges comprised over half of the total load discharged by the WWTP, even though annual CSO discharge is less than 10% of the treated plant discharge. These results indicate that untreated discharges during CSO events can be a major source of some hormones and other wastewater compounds to the environment.

Effectiveness of combined sewer overflow treatment for dissolved oxygen improvement in the Chicago waterways.

PubMed

Alp, E; Melching, C S; Zhang, H; Lanyon, R

2007-01-01

An Use Attainability Analysis (UAA) has been initiated to evaluate what water-quality standards can be achieved in the Chicago Waterway System (CWS). There are nearly 200 combined sewer overflow (CSO) locations discharging to the CWS by gravity. Three CSO pumping stations also drain approximately 140 km2. Because of the dynamic nature of the CWS the DUFLOW model that is capable of simulating hydraulics and water-quality processes under unsteady-flow conditions was used to evaluate the effectiveness of water-quality improvement techniques identified by the UAA including CSO treatment. Several CSO treatment levels were applied at gravity flow CSOs to evaluate improvement in dissolved oxygen (DO). The results show that pollutant removal at CSOs improves DO to a certain degree, but it still was not sufficient to bring DO concentrations to 5 mg/L or higher for 90% of the time during wet weather at most locations on the CWS. Flow from the pumping stations results in substantial stress on DO since a huge amount of un-treated water with a high pollution load is discharged into the CWS in a short period of time at a certain location. The simulation results indicate that CSO treatment does not effectively improve DO during wet-weather periods on the CWS.

Modeling the Hydrologic Effects of Large-Scale Green Infrastructure Projects with GIS

NASA Astrophysics Data System (ADS)

Bado, R. A.; Fekete, B. M.; Khanbilvardi, R.

2015-12-01

Impervious surfaces in urban areas generate excess runoff, which in turn causes flooding, combined sewer overflows, and degradation of adjacent surface waters. Municipal environmental protection agencies have shown a growing interest in mitigating these effects with 'green' infrastructure practices that partially restore the perviousness and water holding capacity of urban centers. Assessment of the performance of current and future green infrastructure projects is hindered by the lack of adequate hydrological modeling tools; conventional techniques fail to account for the complex flow pathways of urban environments, and detailed analyses are difficult to prepare for the very large domains in which green infrastructure projects are implemented. Currently, no standard toolset exists that can rapidly and conveniently predict runoff, consequent inundations, and sewer overflows at a city-wide scale. We demonstrate how streamlined modeling techniques can be used with open-source GIS software to efficiently model runoff in large urban catchments. Hydraulic parameters and flow paths through city blocks, roadways, and sewer drains are automatically generated from GIS layers, and ultimately urban flow simulations can be executed for a variety of rainfall conditions. With this methodology, users can understand the implications of large-scale land use changes and green/gray storm water retention systems on hydraulic loading, peak flow rates, and runoff volumes.

Computing Flows Using Chimera and Unstructured Grids

NASA Technical Reports Server (NTRS)

Liou, Meng-Sing; Zheng, Yao

2006-01-01

DRAGONFLOW is a computer program that solves the Navier-Stokes equations of flows in complexly shaped three-dimensional regions discretized by use of a direct replacement of arbitrary grid overlapping by nonstructured (DRAGON) grid. A DRAGON grid (see figure) is a combination of a chimera grid (a composite of structured subgrids) and a collection of unstructured subgrids. DRAGONFLOW incorporates modified versions of two prior Navier-Stokes-equation-solving programs: OVERFLOW, which is designed to solve on chimera grids; and USM3D, which is used to solve on unstructured grids. A master module controls the invocation of individual modules in the libraries. At each time step of a simulated flow, DRAGONFLOW is invoked on the chimera portion of the DRAGON grid in alternation with USM3D, which is invoked on the unstructured subgrids of the DRAGON grid. The USM3D and OVERFLOW modules then immediately exchange their solutions and other data. As a result, USM3D and OVERFLOW are coupled seamlessly.

Using seismic reflection data to reveal high-resolution structure and pathway of the upper Western Boundary Undercurrent core at Eirik Drift

NASA Astrophysics Data System (ADS)

Müller-Michaelis, Antje; Uenzelmann-Neben, Gabriele

2015-12-01

The method of seismic oceanography was applied to identify fine structure and pathways of the Western Boundary Undercurrent (WBUC) at Eirik Drift, 200 km south of Greenland. Three high-velocity cores of the WBUC were distinguished: a deep core in depths >2600 m which carries Denmark Strait Overflow Water, an upper core in depths between ~1900 and 3000 m transporting Iceland-Scotland Overflow Water, and a split-off of this upper core, which crosses the main crest of Eirik Drift at depths between ~1900 and 2400 m. For the upper WBUC core a detailed analysis of the structure was conducted. The WBUC core has as a domed structure, which changes in style, width and height above seafloor along the lines of the changing topography. We proved not only the influence of the topography on pathway and structure of the WBUC core but also that this information cannot be gained by measuring the overflow waters with discrete CTD stations.

Accretion disks around black holes

NASA Technical Reports Server (NTRS)

Abramowicz, M. A.

1994-01-01

The physics of accretion flow very close to a black hole is dominated by several general relativistic effects. It cannot be described by the standard Shakura Sunyaev model or by its relativistic version developed by Novikov and Thome. The most important of these effects is a dynamical mass loss from the inner edge of the disk (Roche lobe overflow). The relativistic Roche lobe overflow induces a strong advective cooling, which is sufficient to stabilize local, axially symmetric thermal and viscous modes. It also stabilizes the non-axially-symmetric global modes discovered by Papaloizou and Pringle. The Roche lobe overflow, however, destabilizes sufficiently self-gravitating accretion disks with respect to a catastrophic runaway of mass due to minute changes of the gravitational field induced by the changes in the mass and angular momentum of the central black hole. One of the two acoustic modes may become trapped near the inner edge of the disk. All these effects, absent in the standard model, have dramatic implications for time-dependent behavior of the accretion disks around black holes.

Construction dynamics of a lava channel

NASA Astrophysics Data System (ADS)

Harris, Andrew J. L.; Favalli, Massimiliano; Mazzarini, Francesco; Hamilton, Christopher W.

2009-05-01

We use a kinematic GPS and laser range finder survey of a 200 m-long section of the Muliwai a Pele lava channel (Mauna Ulu, Kilauea) to examine the construction processes and flow dynamics responsible for the channel-levee structure. The levees comprise three packages. The basal package comprises an 80-150 m wide 'a'a flow in which a ˜2 m deep and ˜11 m wide channel became centred. This is capped by a second package of thin (<45 cm thick) sheets of pahoehoe extending no more than 50 m from the channel. The upper-most package comprises localised 'a'a overflows. The channel itself contains two blockages located 130 m apart and composed of levee chunks veneered with overflow lava. The channel was emplaced over 50 h, spanning 30 May-2 June, 1974, with the flow front arriving at our section (4.4 km from the vent) 8 h after the eruption began. The basal 'a'a flow thickness yields effusion rates of 35 m3 s-1 for the opening phase, with the initial flow advancing across the mapped section at ˜10 m/min. Short-lived overflows of fluid pahoehoe then built the levee cap, increasing the apparent channel depth to 4.8 m. There were at least six pulses at 90-420 m3 s-1, causing overflow of limited extent lasting no more than 5 min. Brim-full flow conditions were thus extremely short-lived. During a dominant period of below-bank flow, flow depth was ˜2 m with an effusion rate of ˜35 m3 s-1, consistent with the mean output rate (obtained from the total flow bulk volume) of 23-54 m3 s-1. During pulses, levee chunks were plucked and floated down channel to form blockages. In a final low effusion rate phase, lava ponded behind the lower blockage to form a syn-channel pond that fed 'a'a overflow. After the end of the eruption the roofed-over pond continued to drain through the lower blockage, causing the roof to founder. Drainage emplaced inflated flows on the channel floor below the lower blockage for a further ˜10 h. The complex processes involved in levee-channel construction of this short-lived case show that care must be taken when using channel dimensions to infer flow dynamics. In our case, the full channel depth is not exposed. Instead the channel floor morphology reflects late stage pond filling and drainage rather than true channel-contained flow. Components of the compound levee relate to different flow regimes operating at different times during the eruption and associated with different effusion rates, flow dynamics and time scales. For example, although high effusion rate, brim-full flow was maintained for a small fraction of the channel lifetime, it emplaced a pile of pahoehoe overflow units that account for 60% of the total levee height. We show how time-varying volume flux is an important parameter in controlling channel construction dynamics. Because the complex history of lava delivery to a channel system is recorded by the final channel morphology, time-varying flow dynamics can be determined from the channel morphology. Developing methods for quantifying detailed flux histories for effusive events from the evidence in outcrop is therefore highly valuable. We here achieve this by using high-resolution spatial data for a channel system at Kilauea. This study not only indicates those physical and dynamic characteristics that are typical for basaltic lava flows on Hawaiian volcanoes, but also a methodology that can be widely applied to effusive basaltic eruptions.

Drag Prediction for the NASA CRM Wing-Body-Tail Using CFL3D and OVERFLOW on an Overset Mesh

NASA Technical Reports Server (NTRS)

Sclafani, Anthony J.; DeHaan, Mark A.; Vassberg, John C.; Rumsey, Christopher L.; Pulliam, Thomas H.

2010-01-01

In response to the fourth AIAA CFD Drag Prediction Workshop (DPW-IV), the NASA Common Research Model (CRM) wing-body and wing-body-tail configurations are analyzed using the Reynolds-averaged Navier-Stokes (RANS) flow solvers CFL3D and OVERFLOW. Two families of structured, overset grids are built for DPW-IV. Grid Family 1 (GF1) consists of a coarse (7.2 million), medium (16.9 million), fine (56.5 million), and extra-fine (189.4 million) mesh. Grid Family 2 (GF2) is an extension of the first and includes a superfine (714.2 million) and an ultra-fine (2.4 billion) mesh. The medium grid anchors both families with an established build process for accurate cruise drag prediction studies. This base mesh is coarsened and enhanced to form a set of parametrically equivalent grids that increase in size by a factor of roughly 3.4 from one level to the next denser level. Both CFL3D and OVERFLOW are run on GF1 using a consistent numerical approach. Additional OVERFLOW runs are made to study effects of differencing scheme and turbulence model on GF1 and to obtain results for GF2. All CFD results are post-processed using Richardson extrapolation, and approximate grid-converged values of drag are compared. The medium grid is also used to compute a trimmed drag polar for both codes.

Project CARE: reducing wet weather overflows to improve beach water quality. Council Action in Respect of the Environment.

PubMed

Heijs, J; Wilkinson, D; Couriel, E

2002-01-01

The people who live in North Shore City (New Zealand) consider the beaches as their greatest asset. Following public outcry on frequent beach pollution caused by wet weather sewer overflows, Project CARE commenced in 1998 to plan the improvements to the city's separated wastewater and stormwater systems to protect the streams and beaches, particularly from a public health perspective. The investigation included building hydrological and hydraulic models to represent the wastewater and stormwater systems and a receiving waters model to simulate the impacts on the beaches. These models were later used to explore options for improvement. It was found that North Shore City has a very leaky wastewater system that is under capacity. The resulting wet weather overflows (12 per year on average) are the most important contributor to the problem although stormwater pollution alone is big enough to cause problems (at a smaller magnitude). A cost optimisation model (iterative process using performance/cost relationships) was then used to assist in identifying the optimal set of improvement works (storage, repair and increased capacity, wastewater treatment plant) to meet different performance targets and to cater for growth up to the year 2050. Cost Benefit analyses, looking at improvements in system performance and water quality, show diminishing returns for performance levels better than 2 overflows per year. The total costs that meet this target are estimated at almost NZ$300M (US$135M).

Preventive mechanisms of agmatine against ischemic acute kidney injury in rats.

PubMed

Sugiura, Takahiro; Kobuchi, Shuhei; Tsutsui, Hidenobu; Takaoka, Masanori; Fujii, Toshihide; Hayashi, Kentaro; Matsumura, Yasuo

2009-01-28

The excitation of renal sympathetic nervous system plays an important role in the development of ischemic acute kidney injury in rats. Recently, we found that agmatine, an adrenaline alpha(2)/imidazoline I(1)-receptor agonist, has preventive effects on ischemic acute kidney injury by suppressing the enhanced renal sympathetic nerve activity during renal ischemia and by decreasing the renal venous norepinephrine overflow after reperfusion. In the present study, we investigated preventive mechanisms of agmatine against ischemic acute kidney injury in rats. Ischemic acute kidney injury was induced by clamping the left renal artery and vein for 45 min followed by reperfusion, 2 weeks after the contralateral nephrectomy. Pretreatment with efaroxan (30 mumol/kg, i.v.), an alpha(2)/I(1)-receptor antagonist, abolished the suppressive effects of agmatine on the enhanced renal sympathetic nerve activity during renal ischemia and on the elevated norepinephrine overflow after reperfusion, and eliminated the preventing effects of agmatine on the ischemia/reperfusion-induced renal dysfunction and histological damage. On the other hand, pretreatment with yohimbine (6 mumol/kg, i.v.), an alpha(2)-receptor antagonist, eliminated the preventing effects of agmatine on the ischemia/reperfusion-induced renal injury and norepinephrine overflow, without affecting the lowering effect of agmatine on renal sympathetic nerve activity. These results indicate that agmatine prevents the ischemic renal injury by sympathoinhibitory effect probably via I(1) receptors in central nervous system and by suppressing the norepinephrine overflow through alpha(2) or I(1) receptors on sympathetic nerve endings.

Identification of in-sewer sources of organic solids contributing to combined sewer overflows.

PubMed

Ahyerre, M; Chebbo, G

2002-09-01

Previous research has shown that combined sewer systems are the main source of particle and organic pollution during rainfall events contributing to combined sewer overflow. The aim of this article is to identify in an urban catchment area called "Le Marais", in the center of Paris, the types of sediments that are eroded and contribute to the pollution of combined sewer overflow. Three sediment types are considered: granular material found in the inverts of pipes, organic biofilms and organic sediment at the water bed interface, identified as an immobile layer in the "Le Marais" catchment area. The method used consist, firstly, of sampling and assessing the organic pollutant loads and metallic loads of the particles in each type of sediment. Then, the mass of each type of sediment is assessed. The mass and the characteristics of each type of sediment is finally compared to the mass and characteristics of the particles eroded in the catchment area, estimated by mass balances, in order to find the source of eroded particles. The only identified type of deposit that can contribute to combined sewer overflows is the organic layer. Indeed, the solids of this layer have mean and metallic loads that are of the same order of magnitude as the eroded particles. Moreover, the mass of the organic layer considered over different time scales is of the same order of magnitude as the eroded masses during rainfall events and an erosion experiment showed that the organic layer is actually eroded.

Method and apparatus of assessing down-hole drilling conditions

DOEpatents

Hall, David R [Provo, UT; Pixton, David S [Lehl, UT; Johnson, Monte L [Orem, UT; Bartholomew, David B [Springville, UT; Fox, Joe [Spanish Fork, UT

2007-04-24

A method and apparatus for use in assessing down-hole drilling conditions are disclosed. The apparatus includes a drill string, a plurality of sensors, a computing device, and a down-hole network. The sensors are distributed along the length of the drill string and are capable of sensing localized down-hole conditions while drilling. The computing device is coupled to at least one sensor of the plurality of sensors. The data is transmitted from the sensors to the computing device over the down-hole network. The computing device analyzes data output by the sensors and representative of the sensed localized conditions to assess the down-hole drilling conditions. The method includes sensing localized drilling conditions at a plurality of points distributed along the length of a drill string during drilling operations; transmitting data representative of the sensed localized conditions to a predetermined location; and analyzing the transmitted data to assess the down-hole drilling conditions.

Molecular Foundry Workshop draws overflow crowd to BerkeleyLab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, Art

2002-11-27

Nanoscale science and technology is now one of the top research priorities in the United States. With this background, it is no surprise that an overflow crowd or more than 350 registrants filled two auditoriums to hear about and contribute ideas for the new Molecular Foundry during a two-day workshop at the Lawrence Berkeley National Laboratory (Berkeley Lab). Scheduled to open for business at Berkeley Labin early 2006, the Molecular Foundry is one of three Nanoscale Science Research Centers (NSRCs) put forward for funding by the DOE's Office of Basic Energy Sciences (BES).

Concepts, characterization, and modeling of MEMS microswitches with gold contacts in MUMPs

NASA Astrophysics Data System (ADS)

Lafontan, Xavier; Dufaza, Christian; Robert, Michel; Pressecq, Francis; Perez, Guy

2001-04-01

This paper demonstrates that RF MEMS micro-switches can be realized with a low cost MEMS technology such as MUMPs. Two different switches are proposed, namely the hinged beam switch and the gold overflowing switch. Their concepts, design and characterization are described in details. On-resistance as low as 5 - 6 (Omega) for the gold overflowing switch and 2 - 3 (Omega) for the hinged beam switch have been measured. Finally, experimental measurements showed that force and electrical current had strong influences on the overall electrical contact.

Detached Eddy Simulation of the UH-60 Rotor Wake Using Adaptive Mesh Refinement

NASA Technical Reports Server (NTRS)

Chaderjian, Neal M.; Ahmad, Jasim U.

2012-01-01

Time-dependent Navier-Stokes flow simulations have been carried out for a UH-60 rotor with simplified hub in forward flight and hover flight conditions. Flexible rotor blades and flight trim conditions are modeled and established by loosely coupling the OVERFLOW Computational Fluid Dynamics (CFD) code with the CAMRAD II helicopter comprehensive code. High order spatial differences, Adaptive Mesh Refinement (AMR), and Detached Eddy Simulation (DES) are used to obtain highly resolved vortex wakes, where the largest turbulent structures are captured. Special attention is directed towards ensuring the dual time accuracy is within the asymptotic range, and verifying the loose coupling convergence process using AMR. The AMR/DES simulation produced vortical worms for forward flight and hover conditions, similar to previous results obtained for the TRAM rotor in hover. AMR proved to be an efficient means to capture a rotor wake without a priori knowledge of the wake shape.

Haptic seat for fuel economy feedback

DOEpatents

Bobbitt, III, John Thomas

2016-08-30

A process of providing driver fuel economy feedback is disclosed in which vehicle sensors provide for haptic feedback on fuel usage. Such sensors may include one or more of a speed sensors, global position satellite units, vehicle pitch/roll angle sensors, suspension displacement sensors, longitudinal accelerometer sensors, throttle position in sensors, steering angle sensors, break pressure sensors, and lateral accelerometer sensors. Sensors used singlely or collectively can provide enhanced feedback as to various environmental conditions and operating conditions such that a more accurate assessment of fuel economy information can be provided to the driver.

Invertebrates as indicators for chemical stress in sewage-influenced stream systems: toxic and endocrine effects in gammarids and reactions at the community level in two tributaries of Lake Constance, Schussen and Argen.

PubMed

Peschke, Katharina; Geburzi, Jonas; Köhler, Heinz-R; Wurm, Karl; Triebskorn, Rita

2014-08-01

The present study investigates the impact of releases from waste water treatment plants and storm water overflow basins on gammarids and other macrozoobenthos. The study relates to a recent upgrading of a waste water treatment plant (Langwiese) at the Schussen river, an important tributary to Lake Constance. Samples were taken at different sites at the Schussen river upstream and downstream of a storm water overflow basin and the waste water treatment plant Langwiese and, in parallel, at the Argen river, a less polluted reference stream. We assessed the influence of water quality on the distribution of macrozoobenthos and on the health of gammarid populations by a variety of ecotoxicological methods including biomarkers prior to the expansion of the waste water treatment plant. Through histopathological studies, the impact of parasites on host tissue health was evaluated. Analyses of heat shock protein (hsp70) levels allowed us to draw conclusions about the proteotoxicity-related stress status of the organisms. Furthermore, gammarid populations from all sites were investigated in respect to sex ratio, parasitism rate, and fecundity. Macrozoobenthos community integrity was determined by means of the saprobic index and the abundance as well as by the number of taxa. In gammarids, the sex ratio was significantly shifted towards females, fecundity was significantly decreased, and the hsp70 level was significantly increased downstream of the waste water treatment plant Langwiese, compared to the upstream sampling site. Similarly, these effects could be detected downstream of three small storm water overflow basins. In the macrozoobenthos communities, the abundance of taxa, the number of taxa, the number of ephemeroptera, plecoptera, and trichoptera taxa (EPT-taxa), and the number of sensitive taxa decreased downstream of the storm water overflow basin Mariatal as well as downstream of the waste water treatment plant Langwiese. Our study showed, that waste water treatment plants and storm water overflow basins affected macroinvertebrate communities and the health of gammarids. Copyright © 2014 Elsevier Inc. All rights reserved.

Uranium series isotopes concentration in sediments at San Marcos and Luis L. Leon reservoirs, Chihuahua, Mexico

NASA Astrophysics Data System (ADS)

Méndez-García, C.; Renteria-Villalobos, M.; García-Tenorio, R.; Montero-Cabrera, M. E.

2014-07-01

Spatial and temporal distribution of the radioisotopes concentrations were determined in sediments near the surface and core samples extracted from two reservoirs located in an arid region close to Chihuahua City, Mexico. At San Marcos reservoir one core was studied, while from Luis L. Leon reservoir one core from the entrance and another one close to the wall were investigated. 232Th-series, 238U-series, 40K and 137Cs activity concentrations (AC, Bq kg-1) were determined by gamma spectrometry with a high purity Ge detector. 238U and 234U ACs were obtained by liquid scintillation and alpha spectrometry with a surface barrier detector. Dating of core sediments was performed applying CRS method to 210Pb activities. Results were verified by 137Cs AC. Resulting activity concentrations were compared among corresponding surface and core sediments. High 238U-series AC values were found in sediments from San Marcos reservoir, because this site is located close to the Victorino uranium deposit. Low AC values found in Luis L. Leon reservoir suggest that the uranium present in the source of the Sacramento - Chuviscar Rivers is not transported up to the Conchos River. Activity ratios (AR) 234U/overflow="scroll">238U and 238U/overflow="scroll">226Ra in sediments have values between 0.9-1.2, showing a behavior close to radioactive equilibrium in the entire basin. 232Th/overflow="scroll">238U, 228Ra/overflow="scroll">226Ra ARs are witnesses of the different geological origin of sediments from San Marcos and Luis L. Leon reservoirs.

Climate change impacts on the duration and frequency of combined sewer overflows

NASA Astrophysics Data System (ADS)

Fortier, C.; Mailhot, A.

2012-12-01

Combined sewer overflows (CSO) occur when large rainwater inflow from heavy precipitation exceeds the capacity of urban combined sewage systems. Many American and European cities with old sewage systems see their water quality significantly deteriorate during such events. In the long term, changes in the rainfall regime due to climate change may lead to more severe and more frequent CSO episodes and thus compel cities to review their global water management. The overall objective of this study is to investigate how climate change will impact CSO frequency and duration. Data from rain gauges located nearby 30 overflow outfalls, in southern Quebec, Canada, were used to identify rain events leading to overflows, using CSO monitored data from May to October during the period 2007-2009. For each site, occurrence and duration of CSO events were recorded and linked to a rainfall event. Many rain events features can be used to predict CSO events, such as total depth, duration, average intensity and peak intensity. Results based on Pearson product-moment correlation coefficients and multiple regression analysis show that CSO occurrence is best predicted by total rainfall. A methodology is proposed to calculate the CSO probability of occurrence and duration for each site of interest using rainfall series as input data. Monte Carlo method is then used to estimate CSO frequency. To evaluate the climate change impact on CSO, these relationships are used with simulated data from the Canadian Regional Climate Model to compare the distribution of annual number of CSO events over the 1960-1990 period and the 2070-2100 period.

SLUDGE PARTICLE SEPAPATION EFFICIENCIES DURING SETTLER TANK RETRIEVAL INTO SCS-CON-230

DOE Office of Scientific and Technical Information (OSTI.GOV)

DEARING JI; EPSTEIN M; PLYS MG

2009-07-16

The purpose of this document is to release, into the Hanford Document Control System, FA1/0991, Sludge Particle Separation Efficiencies for the Rectangular SCS-CON-230 Container, by M. Epstein and M. G. Plys, Fauske & Associates, LLC, June 2009. The Sludge Treatment Project (STP) will retrieve sludge from the 105-K West Integrated Water Treatment System (IWTS) Settler Tanks and transfer it to container SCS-CON-230 using the Settler Tank Retrieval System (STRS). The sludge will enter the container through two distributors. The container will have a filtration system that is designed to minimize the overflow of sludge fines from the container to themore » basin. FAI/09-91 was performed to quantify the effect of the STRS on sludge distribution inside of and overflow out of SCS-CON-230. Selected results of the analysis and a system description are discussed. The principal result of the analysis is that the STRS filtration system reduces the overflow of sludge from SCS-CON-230 to the basin by roughly a factor of 10. Some turbidity can be expected in the center bay where the container is located. The exact amount of overflow and subsequent turbidity is dependent on the density of the sludge (which will vary with location in the Settler Tanks) and the thermal gradient between the SCS-CON-230 and the basin. Attachment A presents the full analytical results. These results are applicable specifically to SCS-CON-230 and the STRS filtration system's expected operating duty cycles.« less

Allocation to carbon storage pools in Norway spruce saplings under drought and low CO2.

PubMed

Hartmann, Henrik; McDowell, Nate G; Trumbore, Susan

2015-03-01

Non-structural carbohydrates (NSCs) are critical to maintain plant metabolism under stressful environmental conditions, but we do not fully understand how NSC allocation and utilization from storage varies with stress. While it has become established that storage allocation is unlikely to be a mere overflow process, very little empirical evidence has been produced to support this view, at least not for trees. Here we present the results of an intensively monitored experimental manipulation of whole-tree carbon (C) balance (young Picea abies (L.) H Karst.) using reduced atmospheric [CO2] and drought to reduce C sources. We measured specific C storage pools (glucose, fructose, sucrose, starch) over 21 weeks and converted concentration measurement into fluxes into and out of the storage pool. Continuous labeling ((13)C) allowed us to track C allocation to biomass and non-structural C pools. Net C fluxes into the storage pool occurred mainly when the C balance was positive. Storage pools increased during periods of positive C gain and were reduced under negative C gain. (13)C data showed that C was allocated to storage pools independent of the net flux and even under severe C limitation. Allocation to below-ground tissues was strongest in control trees followed by trees experiencing drought followed by those grown under low [CO2]. Our data suggest that NSC storage has, under the conditions of our experimental manipulation (e.g., strong progressive drought, no above-ground growth), a high allocation priority and cannot be considered an overflow process. While these results also suggest active storage allocation, definitive proof of active plant control of storage in woody plants requires studies involving molecular tools. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Reduction of bacteria and somatic coliphages in constructed wetlands for the treatment of combined sewer overflow (retention soil filters).

PubMed

Ruppelt, Jan P; Tondera, Katharina; Schreiber, Christiane; Kistemann, Thomas; Pinnekamp, Johannes

2018-05-01

Combined sewer overflows (CSOs) introduce numerous pathogens from fecal contamination, such as bacteria and viruses, into surface waters, thus endangering human health. In Germany, retention soil filters (RSFs) treat CSOs at sensitive discharge points and can contribute to reducing these hygienically relevant microorganisms. In this study, we evaluated the extent of how dry period, series connection and filter layer thickness influence the reduction efficiency of RSFs for Escherichia coli (E. coli), intestinal enterococci (I. E.) and somatic coliphages. To accomplish this, we had four pilot scale RSFs built on a test field at the wastewater treatment plant Aachen-Soers. While two filters were replicates, the other two filters were installed in a series connection. Moreover, one filter had a thinner filtration layer than the other three. Between April 2015 and December 2016, the RSFs were loaded in 37 trials with pre-conditioned CSO after dry periods ranging from 4 to 40 days. During 17 trials, samples for microbial analysis were taken and analyzed. The series connection of two filters showed that the removal increases when two systems with a filter layer of the same height are operated in series. Since the microorganisms are exposed twice to the environmental conditions on the filter surface and in the upper filter layers, there is a greater chance for abiotic adsorption increase. The same effect could be shown when filters with different depths were compared: the removal efficiency increases as filter thickness increases. This study provides new evidence that regardless of seasonal effects and dry period, RSFs can improve hygienic situation significantly. Copyright © 2018 Elsevier GmbH. All rights reserved.

THE QUASI-ROCHE LOBE OVERFLOW STATE IN THE EVOLUTION OF CLOSE BINARY SYSTEMS CONTAINING A RADIO PULSAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benvenuto, O. G.; De Vito, M. A.; Horvath, J. E., E-mail: adevito@fcaglp.unlp.edu.ar, E-mail: foton@iag.usp.br

We study the evolution of close binary systems formed by a normal (solar composition), intermediate-mass-donor star together with a neutron star. We consider models including irradiation feedback and evaporation. These nonstandard ingredients deeply modify the mass-transfer stages of these binaries. While models that neglect irradiation feedback undergo continuous, long-standing mass-transfer episodes, models including these effects suffer a number of cycles of mass transfer and detachment. During mass transfer, the systems should reveal themselves as low-mass X-ray binaries (LMXBs), whereas when they are detached they behave as binary radio pulsars. We show that at these stages irradiated models are in amore » Roche lobe overflow (RLOF) state or in a quasi-RLOF state. Quasi-RLOF stars have radii slightly smaller than their Roche lobes. Remarkably, these conditions are attained for an orbital period as well as donor mass values in the range corresponding to a family of binary radio pulsars known as ''redbacks''. Thus, redback companions should be quasi-RLOF stars. We show that the characteristics of the redback system PSR J1723-2837 are accounted for by these models. In each mass-transfer cycle these systems should switch from LMXB to binary radio pulsar states with a timescale of approximately one million years. However, there is recent and fast growing evidence of systems switching on far shorter, human timescales. This should be related to instabilities in the accretion disk surrounding the neutron star and/or radio ejection, still to be included in the model having the quasi-RLOF state as a general condition.« less

Automated inundation monitoring using TerraSAR-X multitemporal imagery

NASA Astrophysics Data System (ADS)

Gebhardt, S.; Huth, J.; Wehrmann, T.; Schettler, I.; Künzer, C.; Schmidt, M.; Dech, S.

2009-04-01

The Mekong Delta in Vietnam offers natural resources for several million inhabitants. However, a strong population increase, changing climatic conditions and regulatory measures at the upper reaches of the Mekong lead to severe changes in the Delta. Extreme flood events occur more frequently, drinking water availability is increasingly limited, soils show signs of salinization or acidification, species and complete habitats diminish. During the Monsoon season the river regularly overflows its banks in the lower Mekong area, usually with beneficial effects. However, extreme flood events occur more frequently causing extensive damage, on the average once every 6 to 10 years river flood levels exceed the critical beneficial level X-band SAR data are well suited for deriving inundated surface areas. The TerraSAR-X sensor with its different scanning modi allows for the derivation of spatial and temporal high resolved inundation masks. The paper presents an automated procedure for deriving inundated areas from TerraSAR-X Scansar and Stripmap image data. Within the framework of the German-Vietnamese WISDOM project, focussing the Mekong Delta region in Vietnam, images have been acquired covering the flood season from June 2008 to November 2008. Based on these images a time series of the so called watermask showing inundated areas have been derived. The product is required as intermediate to (i) calibrate 2d inundation model scenarios, (ii) estimate the extent of affected areas, and (iii) analyze the scope of prior crisis. The image processing approach is based on the assumption that water surfaces are forward scattering the radar signal resulting in low backscatter signals to the sensor. It uses multiple grey level thresholds and image morphological operations. The approach is robust in terms of automation, accuracy, robustness, and processing time. The resulting watermasks show the seasonal flooding pattern with inundations starting in July, having their peak at the end of September, and lower down until December in 2008. The results are a valuable input for monitoring and understanding the seasonal regional flood patterns for calibrating 2d inundation models, as also for generating value added products in combination with agricultural land use and socio-economic data for further separation of inundated and irrigated areas.

Assessment of spill flow emissions on the basis of measured precipitation and waste water data

NASA Astrophysics Data System (ADS)

Hochedlinger, Martin; Gruber, Günter; Kainz, Harald

2005-09-01

Combined sewer overflows (CSOs) are substantial contributors to the total emissions into surface water bodies. The emitted pollution results from dry-weather waste water loads, surface runoff pollution and from the remobilisation of sewer deposits and sewer slime during storm events. One possibility to estimate overflow loads is a calculation with load quantification models. Input data for these models are pollution concentrations, e.g. Total Chemical Oxygen Demand (COD tot), Total Suspended Solids (TSS) or Soluble Chemical Oxygen Demand (COD sol), rainfall series and flow measurements for model calibration and validation. It is important for the result of overflow loads to model with reliable input data, otherwise this inevitably leads to bad results. In this paper the correction of precipitation measurements and the sewer online-measurements are presented to satisfy the load quantification model requirements already described. The main focus is on tipping bucket gauge measurements and their corrections. The results evidence the importance of their corrections due the effects on load quantification modelling and show the difference between corrected and not corrected data of storm events with high rain intensities.

Water Quality of Combined Sewer Overflows, Stormwater, and Streams, Omaha, Nebraska, 2006-07

USGS Publications Warehouse

Vogel, Jason R.; Frankforter, Jill D.; Rus, David L.; Hobza, Christopher M.; Moser, Matthew T.

2009-01-01

The U.S. Geological Survey, in cooperation with the City of Omaha, investigated the water quality of combined sewer overflows, stormwater, and streams in the Omaha, Nebraska, area by collecting and analyzing 1,175 water samples from August 2006 through October 2007. The study area included the drainage area of Papillion Creek at Capeheart Road near Bellevue, Nebraska, which encompasses the tributary drainages of the Big and Little Papillion Creeks and Cole Creek, along with the Missouri River reach that is adjacent to Omaha. Of the 101 constituents analyzed during the study, 100 were detected in at least 1 sample during the study. Spatial and seasonal comparisons were completed for environmental samples. Measured concentrations in stream samples were compared to water-quality criteria for pollutants of concern. Finally, the mass loads of water-quality constituents in the combined sewer overflow discharges, stormwater outfalls, and streams were computed and compared. The results of the study indicate that combined sewer overflow and stormwater discharges are affecting the water quality of the streams in the Omaha area. At the Papillion Creek Basin sites, Escherichia coli densities were greater than 126 units per 100 milliliters in 99 percent of the samples (212 of 213 samples analyzed for Escherichia coli) collected during the recreational-use season from May through September (in 2006 and 2007). Escherichia coli densities in 76 percent of Missouri River samples (39 of 51 samples) were greater than 126 units per 100 milliliters in samples collected from May through September (in 2006 and 2007). None of the constituents with human health criteria for consumption of water, fish, and other aquatic organisms were detected at levels greater than the criteria in any of the samples collected during this study. Total phosphorus concentrations in water samples collected in the Papillion Creek Basin were in excess of the U.S. Environmental Protection Agency's proposed criterion in all but four stream samples (266 of 270). Similarly, only 2 of 84 Missouri River samples had total phosphorus concentrations less than the proposed criterion. The proposed total nitrogen criterion for the Corn Belt and Northern Great Plains ecoregion was surpassed in 80 percent of the water samples collected from the stream sites. Samples with total nitrogen concentrations greater than the proposed criterion were most common at Papillion Creek and Big Papillion Creek sites, where the proposed criterion was surpassed in 90 and 96 percent of the samples collected, respectively. Elevated concentrations of total nitrogen were less common at the Missouri River sites, with 33 percent of the samples analyzed having concentrations that surpassed the proposed nutrient criterion for total nitrogen. The three constituents with measured concentrations greater than their respective health-based screening levels were nickel, zinc, and dichlorvos. Differences in water quality during the beginning, middle, and end of the combined sewer overflow discharge and the stream hydrograph rise, peak, and recession were investigated. Concentrations from the ending part of the combined sewer overflow hydrograph were significantly different than those from the beginning and middle parts for 3 and 11 constituents, respectively. No constituents were significantly different between the beginning and middle parts of the combined sewer overflow discharge hydrograph. For the stream site upstream from combined sewer overflow outfalls on Cole Creek, the constituents with geometric mean values for the hydrograph rise that were at least twice those for the values of the peak and recession were specific conductance, magnesium, nitrite, N,N-diethyl-meta-toluamide (DEET), methyl salicylate, p-cresol, and Escherichia coli. Similarly, the constituents where the hydrograph peak was at least twice that for the rise and recession at the upstream Cole Creek site were total suspended solids, silver, an

Density currents in the Chicago River: Characterization, effects on water quality, and potential sources

USGS Publications Warehouse

Jackson, P. Ryan; Garcia, Carlos M.; Oberg, Kevin A.; Johnson, Kevin K.; Garcia, Marcelo H.

2008-01-01

Bidirectional flows in a river system can occur under stratified flow conditions and in addition to creating significant errors in discharge estimates, the upstream propagating currents are capable of transporting contaminants and affecting water quality. Detailed field observations of bidirectional flows were made in the Chicago River in Chicago, Illinois in the winter of 2005-06. Using multiple acoustic Doppler current profilers simultaneously with a water-quality profiler, the formation of upstream propagating density currents within the Chicago River both as an underflow and an overflow was observed on three occasions. Density differences driving the flow primarily arise from salinity differences between intersecting branches of the Chicago River, whereas water temperature is secondary in the creation of these currents. Deicing salts appear to be the primary source of salinity in the North Branch of the Chicago River, entering the waterway through direct runoff and effluent from a wastewater-treatment plant in a large metropolitan area primarily served by combined sewers. Water-quality assessments of the Chicago River may underestimate (or overestimate) the impairment of the river because standard water-quality monitoring practices do not account for density-driven underflows (or overflows). Chloride concentrations near the riverbed can significantly exceed concentrations at the river surface during underflows indicating that full-depth parameter profiles are necessary for accurate water-quality assessments in urban environments where application of deicing salt is common.

The fate of recently fixed carbon after drought release: towards unravelling C storage regulation in Tilia platyphyllos and Pinus sylvestris.

PubMed

Galiano, Lucía; Timofeeva, Galina; Saurer, Matthias; Siegwolf, Rolf; Martínez-Vilalta, Jordi; Hommel, Robert; Gessler, Arthur

2017-09-01

Carbon reserves are important for maintaining tree function during and after stress. Increasing tree mortality driven by drought globally has renewed the interest in how plants regulate allocation of recently fixed C to reserve formation. Three-year-old seedlings of two species (Tilia platyphyllos and Pinus sylvestris) were exposed to two intensities of experimental drought during ~10 weeks, and 13 C pulse labelling was subsequently applied with rewetting. Tracking the 13 C label across different organs and C compounds (soluble sugars, starch, myo-inositol, lipids and cellulose), together with the monitoring of gas exchange and C mass balances over time, allowed for the identification of variations in C allocation priorities and tree C balances that are associated with drought effects and subsequent drought release. The results demonstrate that soluble sugars accumulated in P. sylvestris under drought conditions independently of growth trends; thus, non-structural carbohydrates (NSC) formation cannot be simply considered a passive overflow process in this species. Once drought ceased, C allocation to storage was still prioritized at the expense of growth, which suggested the presence of 'drought memory effects', possibly to ensure future growth and survival. On the contrary, NSC and growth dynamics in T. platyphyllos were consistent with a passive (overflow) view of NSC formation. © 2017 John Wiley & Sons Ltd.

Probabilistic modelling of overflow, surcharge and flooding in urban drainage using the first-order reliability method and parameterization of local rain series.

PubMed

Thorndahl, S; Willems, P

2008-01-01

Failure of urban drainage systems may occur due to surcharge or flooding at specific manholes in the system, or due to overflows from combined sewer systems to receiving waters. To quantify the probability or return period of failure, standard approaches make use of the simulation of design storms or long historical rainfall series in a hydrodynamic model of the urban drainage system. In this paper, an alternative probabilistic method is investigated: the first-order reliability method (FORM). To apply this method, a long rainfall time series was divided in rainstorms (rain events), and each rainstorm conceptualized to a synthetic rainfall hyetograph by a Gaussian shape with the parameters rainstorm depth, duration and peak intensity. Probability distributions were calibrated for these three parameters and used on the basis of the failure probability estimation, together with a hydrodynamic simulation model to determine the failure conditions for each set of parameters. The method takes into account the uncertainties involved in the rainstorm parameterization. Comparison is made between the failure probability results of the FORM method, the standard method using long-term simulations and alternative methods based on random sampling (Monte Carlo direct sampling and importance sampling). It is concluded that without crucial influence on the modelling accuracy, the FORM is very applicable as an alternative to traditional long-term simulations of urban drainage systems.

Efficient bulk-loading of gridfiles

NASA Technical Reports Server (NTRS)

Leutenegger, Scott T.; Nicol, David M.

1994-01-01

This paper considers the problem of bulk-loading large data sets for the gridfile multiattribute indexing technique. We propose a rectilinear partitioning algorithm that heuristically seeks to minimize the size of the gridfile needed to ensure no bucket overflows. Empirical studies on both synthetic data sets and on data sets drawn from computational fluid dynamics applications demonstrate that our algorithm is very efficient, and is able to handle large data sets. In addition, we present an algorithm for bulk-loading data sets too large to fit in main memory. Utilizing a sort of the entire data set it creates a gridfile without incurring any overflows.

Performance of the Widely-Used CFD Code OVERFLOW on the Pleides Supercomputer

NASA Technical Reports Server (NTRS)

Guruswamy, Guru P.

2017-01-01

Computational performance studies were made for NASA's widely used Computational Fluid Dynamics code OVERFLOW on the Pleiades Supercomputer. Two test cases were considered: a full launch vehicle with a grid of 286 million points and a full rotorcraft model with a grid of 614 million points. Computations using up to 8000 cores were run on Sandy Bridge and Ivy Bridge nodes. Performance was monitored using times reported in the day files from the Portable Batch System utility. Results for two grid topologies are presented and compared in detail. Observations and suggestions for future work are made.

Geometric scaling of artificial hair sensors for flow measurement under different conditions

NASA Astrophysics Data System (ADS)

Su, Weihua; Reich, Gregory W.

2017-03-01

Artificial hair sensors (AHSs) have been developed for prediction of the local flow speed and aerodynamic force around an airfoil and subsequent application in vibration control of the airfoil. Usually, a specific sensor design is only sensitive to the flow speeds within its operating flow measurement region. This paper aims at expanding this flow measurement concept of using AHSs to different flow speed conditions by properly sizing the parameters of the sensors, including the dimensions of the artificial hair, capillary, and carbon nanotubes (CNTs) that make up the sensor design, based on a baseline sensor design and its working flow condition. In doing so, the glass fiber hair is modeled as a cantilever beam with an elastic foundation, subject to the distributed aerodynamic drag over the length of the hair. Hair length and diameter, capillary depth, and CNT height are scaled by keeping the maximum compressive strain of the CNTs constant for different sensors under different speed conditions. Numerical studies will demonstrate the feasibility of the geometric scaling methodology by designing AHSs for aircraft with different dimensions and flight conditions, starting from the same baseline sensor. Finally, the operating bandwidth of the scaled sensors are explored.

Runoff production from intercrater plains on Mars

NASA Astrophysics Data System (ADS)

Irwin, R. P., III; Matsubara, Y.; Cawley, J. C.

2016-12-01

Ancient fluvial paleochannels and paleolakes constrain the hydrology of a wetter epoch in the early history of Mars. The cross-sectional dimensions of fluvial channels scale with discharge, watershed topography is generally well preserved, and adjustments can be made for gravity. These factors have supported conservative estimates of runoff production during event floods more than 3.5 billion years ago. Assuming weak channel banks, such that discharge is low per unit channel width, event floods in smaller watersheds had estimated runoff production of 1 cm/day. Highland surfaces generated runoff inefficiently, such that channel width increases with only the 0.3 power of watershed area. Inefficient runoff production on Mars is also suggested by new landscape evolution modeling. In long-term simulations that accurately reproduce the present landscape, forming and degrading all of the Middle and Late Noachian impact craters in selected study areas, inefficient runoff production is needed to degrade craters without intensely dissecting intercrater surfaces. The model shows that discharge generally cannot increase at more than the 0.3 power of watershed area. Paleolakes provide useful constraints on paleohydrology over intermediate timescales of years to millennia. Most local highland basins were never integrated into regional drainage systems, but some have both a contributing valley network and an outlet valley, indicating that they overflowed. Paleolake overflows require a medium-term water supply that exceeds losses to evaporation. Reasonable evaporation of 0.1 to 1 m/yr and watersheds that are mostly >10 times the area of overflowed paleolakes suggest runoff production of <0.1 m per year. Event floods were both moderate and rare during peak fluvial conditions on Mars. Over the bulk of the Middle and Late Noachian Epochs, the loss of small craters, scarp retreat, and basin infilling suggest less intense fluvial activity along with weathering, impact gardening, and lesser aeolian erosion. Low drainage density is an obvious explanation for inefficient runoff production, but it may be the consequence of moderate rainfall or snowmelt, as well as incision of valley networks over a finite timescale.

Position Sensor with Integrated Signal-Conditioning Electronics on a Printed Wiring Board

NASA Technical Reports Server (NTRS)

Alhorn, Dean C. (Inventor); Howard, David E. (Inventor); Smith, Dennis A. (Inventor)

2001-01-01

A position sensor, such as a rotary position sensor, includes the signal-conditioning electronics in the housing. The signal-conditioning electronics are disposed on a printed wiring board, which is assembled with another printed wiring board including the sensor windings to provide a sub-assembly. A mu-metal shield is interposed between the printed wiring boards to prevent magnetic interference. The sub-assembly is disposed in the sensor housing adjacent to an inductor board which turns on a shaft. The inductor board emanates an internally or externally generated excitation signal that induces a signal in the sensor windings. The induced signal represents the rotary position of the inductor board relative to the sensor winding board.

Sensing Challenges for Controls and PHM in the Hostile Operating Conditions of Modern Turbine Engine (Postprint)

DTIC Science & Technology

2008-07-01

SUBJECT TERMS Gas turbine, sensors, Hostile Operating Conditions, FADEC , High Temperature Regimes for Sensors, Sensor Needs, Turbine Engine...Authority Digital Engine Control ( FADEC ). The frequency and bandwidth capability of sensors for engine control are drastically different for each sensor...metering valve assembly is responsive to electrical signals generated by the FADEC in response to sensors that measure turbine speed, pressure

Continuous glucose monitoring--a study of the Enlite sensor during hypo- and hyperbaric conditions.

PubMed

Adolfsson, Peter; Örnhagen, Hans; Eriksson, Bengt M; Cooper, Ken; Jendle, Johan

2012-06-01

The performance and accuracy of the Enlite(™) (Medtronic, Inc., Northridge, CA) sensor may be affected by microbubble formation at the electrode surface during hypo- and hyperbaric conditions. The effects of acute pressure changes and of prewetting of sensors were investigated. On Day 1, 24 sensors were inserted on the right side of the abdomen and back in one healthy individual; 12 were prewetted with saline solution, and 12 were inserted dry. On Day 2, this procedure was repeated on the left side. All sensors were attached to an iPro continuous glucose monitoring (CGM) recorder. Hypobaric and hyperbaric tests were conducted in a pressure chamber, with each test lasting 105 min. Plasma glucose values were obtained at 5-min intervals with a HemoCue(®) (Ängelholm, Sweden) model 201 glucose analyzer for comparison with sensor glucose values. Ninety percent of the CGM systems operated during the tests. The mean absolute relative difference was lower during hyperbaric than hypobaric conditions (6.7% vs. 14.9%, P<0.001). Sensor sensitivity was slightly decreased (P<0.05) during hypobaric but not during hyperbaric conditions. Clarke Error Grid Analysis showed that 100% of the values were found in the A+B region. No differences were found between prewetted and dry sensors. The Enlite sensor performed adequately during acute pressure changes and was more accurate during hyperbaric than hypobaric conditions. Prewetting the sensors did not improve accuracy. Further studies on type 1 diabetes subjects are needed under various pressure conditions.

Improving the production of acetyl-CoA-derived chemicals in Escherichia coli BL21(DE3) through iclR and arcA deletion.

PubMed

Liu, Min; Ding, Yamei; Chen, Hailin; Zhao, Zhe; Liu, Huizhou; Xian, Mo; Zhao, Guang

2017-01-07

Acetyl-CoA-derived chemicals are suitable for multiple applications in many industries. The bio-production of these chemicals has become imperative owing to the economic and environmental problems. However, acetate overflow is the major drawback for acetyl-CoA-derived chemicals production. Approaches for overcoming acetate overflow may be beneficial for the production of acetyl-CoA-derived chemicals. In this study, a transcriptional regulator iclR was knocked out in E.coli BL21(DE3) to overcome acetate overflow and improve the chemicals production. Two important acetyl-CoA-derived chemicals, phloroglucinol (PG) and 3-hydroxypropionate (3HP) were used to evaluate it. It is revealed that knockout of iclR significantly increased expressions of aceBAK operon. The cell yields and glucose utilization efficiencies were higher than those of control strains. The acetate concentrations were decreased by more than 50% and the productions of PG and 3HP were increased more than twice in iclR mutants. The effects of iclR knockout on cell physiology, cell metabolism and production of acetyl-CoA-derived chemicals were similar to those of arcA knockout in our previous study. However, the arcA-iclR double mutants couldn't gain higher productions of PG and 3HP. The mechanisms are unclear and needed to be resolved in future. Knockout of iclR significantly increased gene expression of aceBAK operon and concomitantly activated glyoxylate pathway. This genetic modification may be a good way to overcome acetate overflow, and improve the production of a wide range of acetyl-CoA-derived chemicals.

Hidden overflow pathway to L-phenylalanine in Pseudomonas aeruginosa.

PubMed Central

Fiske, M J; Whitaker, R J; Jensen, R A

1983-01-01

Pseudomonas aeruginosa is representative of a large group of pseudomonad bacteria that possess coexisting alternative pathways to L-phenylalanine (as well as to L-tyrosine). These multiple flow routes to aromatic end products apparently account for the inordinate resistance of P. aeruginosa to end product analogs. Manipulation of carbon source nutrition produced a physiological state of sensitivity to p-fluorophenylalanine and m-fluorophenylalanine, each a specific antimetabolite of L-phenylalanine. Analog-resistant mutants obtained fell into two classes. One type lacked feedback sensitivity of prephenate dehydratase and was the most dramatic excretor of L-phenylalanine. The presence of L-tyrosine curbed phenylalanine excretion to one-third, a finding explained by potent early-pathway regulation of 3-deoxy-D-arabinoheptulosonate 7-phosphate (DAHP) synthase-Tyr (a DAHP synthase subject to allosteric inhibition by L-tyrosine). The second class of regulatory mutants possessed a completely feedback-resistant DAHP synthase-Tyr, the major species (greater than 90%) of two isozymes. Deregulation of DAHP synthase-Tyr resulted in the escape of most chorismate molecules produced into an unregulated overflow route consisting of chorismate mutase (monofunctional), prephenate aminotransferase, and arogenate dehydratase. In the wild type the operation of the overflow pathway is restrained by factors that restrict early-pathway flux. These factors include the highly potent feedback control of DAHP synthase isozymes by end products as well as the strikingly variable abilities of different carbon source nutrients to supply the aromatic pathway with beginning substrates. Even in the wild type, where all allosteric regulation in intact, some phenylalanine overflow was found on glucose-based medium, but not on fructose-based medium. This carbon source-dependent difference was much more exaggerated in each class of regulatory mutants. PMID:6132913

Differences in glance behavior between drivers using a rearview camera, parking sensor system, both technologies, or no technology during low-speed parking maneuvers.

PubMed

Kidd, David G; McCartt, Anne T

2016-02-01

This study characterized the use of various fields of view during low-speed parking maneuvers by drivers with a rearview camera, a sensor system, a camera and sensor system combined, or neither technology. Participants performed four different low-speed parking maneuvers five times. Glances to different fields of view the second time through the four maneuvers were coded along with the glance locations at the onset of the audible warning from the sensor system and immediately after the warning for participants in the sensor and camera-plus-sensor conditions. Overall, the results suggest that information from cameras and/or sensor systems is used in place of mirrors and shoulder glances. Participants with a camera, sensor system, or both technologies looked over their shoulders significantly less than participants without technology. Participants with cameras (camera and camera-plus-sensor conditions) used their mirrors significantly less compared with participants without cameras (no-technology and sensor conditions). Participants in the camera-plus-sensor condition looked at the center console/camera display for a smaller percentage of the time during the low-speed maneuvers than participants in the camera condition and glanced more frequently to the center console/camera display immediately after the warning from the sensor system compared with the frequency of glances to this location at warning onset. Although this increase was not statistically significant, the pattern suggests that participants in the camera-plus-sensor condition may have used the warning as a cue to look at the camera display. The observed differences in glance behavior between study groups were illustrated by relating it to the visibility of a 12-15-month-old child-size object. These findings provide evidence that drivers adapt their glance behavior during low-speed parking maneuvers following extended use of rearview cameras and parking sensors, and suggest that other technologies which augment the driving task may do the same. Copyright © 2015 Elsevier Ltd. All rights reserved.

Smart sensor technology for advanced launch vehicles

NASA Astrophysics Data System (ADS)

Schoess, Jeff

1989-07-01

Next-generation advanced launch vehicles will require improved use of sensor data and the management of multisensor resources to achieve automated preflight checkout, prelaunch readiness assessment and vehicle inflight condition monitoring. Smart sensor technology is a key component in meeting these needs. This paper describes the development of a smart sensor-based condition monitoring system concept referred to as the Distributed Sensor Architecture. A significant event and anomaly detection scheme that provides real-time condition assessment and fault diagnosis of advanced launch system rocket engines is described. The design and flight test of a smart autonomous sensor for Space Shuttle structural integrity health monitoring is presented.

Verification of Reproduction Simulation of the 2011 Great East Japan Tsunami Using Time-Stamp Data

NASA Astrophysics Data System (ADS)

Honma, Motohiro; Ushiyama, Motoyuki

2014-05-01

In the 2011 off the pacific coast of Tohoku earthquake tsunami, the significant damage and loss of lives were caused by large tsunami in the pacific coastal areas of the northern Japan. It is important to understand the situation of tsunami inundation in detail in order to establish the effective measures of disaster prevention. In this study, we calculated the detailed tsunami inundation simulation of Rikuzentakata city and verified the simulation results using not only the static observed data such as inundation area and tsunami height estimated by traces but also time stamp data which were recorded to digital camera etc. We calculated the tsunami simulation by non-linear long-wave theory using the staggered grid and leap flog scheme. We used Fujii and Satake (2011)'s model ver.4.2 as the tsunami source. The inundation model of Rikuzentakata city was constructed by fine ground level data of 10m mesh. In this simulation, the shore and river banks were set in boundary of calculation mesh. At that time, we have calculated two patterns of simulation, one condition is that a bank doesn't collapse even if tsunami overflows on it, another condition is that a bank collapses if tsunami overflows on it and its discharge exceeds the threshold. We can use the inundation area data, which was obtained by Geospatial Information Authority of Japan (GSI), and height data of tsunami trace, which were obtained by the 2011 Tohoku Earthquake Joint Survey (TTJS) group, as "static" verification data. Comparing the inundation area of simulation result with its observation by GSI, both areas are matched very well. And then, correlation coefficient between tsunami height data resulted from simulation and observed by TTJS is 0.756. In order to verify tsunami arrival time, we used the time stamp data which were recorded to digital camera etc. by citizens. Ushiyama and Yokomaku (2012) collected these tsunami stamp data and estimated the arrival time in Rikuzentakata city. We compared the arrival time resulted from tsunami simulation with estimated by Ushiyama and Yokomaku (2012) for some major points. The arrival time is earlier 2-4 minutes in the condition that a bank collapses when tsunami overflows and its discharge exceeds 0.05m2/s at each mesh boundary than in the condition that a bank doesn't collapse. And, on the whole the arrival time estimated from time stamp data is in accord with the result which were calculated in the condition that a bank collapse. We could verify reproducibility about not only the final tsunami inundation situation but also the temporal change of tsunami inundation situation by using the time stamp data. Acknowledgement In this study, we used tsunami trace data obtained by The 2011 Tohoku Earthquake Tsunami Joint Survey (TTJS) Group. Reference 1) Fujii and Satake: Tsunami Source of the Off Tohoku-Pacific Earthquake on March 11, 2011, http://iisee.kenken.go.jp/staff/fujii/OffTohokuPacific2011/tsunami_ja_ver4.2and4.6.html, 2011. 2) Ushiyama and Yokomaku: Estimation of situation in Rikuzentakata city just before tsunami attack based on time stamp data, J.JSNDS31-1, pp.47-58, 2012.

Dynamic Simulation of a Periodic 10 K Sorption Cryocooler

NASA Technical Reports Server (NTRS)

Bhandari, P.; Rodriguez, J.; Bard, S.; Wade, L.

1994-01-01

A transient thermal simulation model has been developed to simulate the dynamic performance of a multiple-stage 10 K sorption cryocooler for spacecraft sensor cooling applications that require periodic quick-cooldown (under 2 minutes) , negligible vibration, low power consumption, and long life (5 to 10 years). The model was specifically designed to represent the Brilliant Eyes Ten-Kelvin Sorption Cryocooler Experiment (BETSCE), but it can be adapted to represent other sorption cryocooler systems as well. The model simulates the heat transfer, mass transfer, and thermodynamic processes in the cryostat and the sorbent beds for the entire refrigeration cycle, and includes the transient effects of variable hydrogen supply pressures due to expansion and overflow of hydrogen during the cooldown operation. The paper describes model limitations and simplifying assumptions, with estimates of errors induced by them, and presents comparisons of performance predictions with ground experiments. An important benefit of the model is its ability to predict performance sensitivities to variations of key design and operational parameters. The insights thus obtained are expected to lead to higher efficiencies and lower weights for future designs.

Fiber optic voice/data network

NASA Technical Reports Server (NTRS)

Bergman, Larry A. (Inventor)

1989-01-01

An asynchronous, high-speed, fiber optic local area network originally developed for tactical environments with additional benefits for other environments such as spacecraft, and the like. The network supports ordinary data packet traffic simultaneously with synchronous T1 voice traffic over a common token ring channel; however, the techniques and apparatus of this invention can be applied to any deterministic class of packet data networks, including multitier backbones, that must transport stream data (e.g., video, SAR, sensors) as well as data. A voice interface module parses, buffers, and resynchronizes the voice data to the packet network employing elastic buffers on both the sending and receiving ends. Voice call setup and switching functions are performed external to the network with ordinary PABX equipment. Clock information is passed across network boundaries in a token passing ring by preceeding the token with an idle period of non-transmission which allows the token to be used to re-establish a clock synchronized to the data. Provision is made to monitor and compensate the elastic receiving buffers so as to prevent them from overflowing or going empty.

Groundwater infiltration, surface water inflow and sewerage exfiltration considering hydrodynamic conditions in sewer systems.

PubMed

Karpf, Christian; Hoeft, Stefan; Scheffer, Claudia; Fuchs, Lothar; Krebs, Peter

2011-01-01

Sewer systems are closely interlinked with groundwater and surface water. Due to leaks and regular openings in the sewer system (e.g. combined sewer overflow structures with sometimes reverse pressure conditions), groundwater infiltration and surface water inflow as well as exfiltration of sewage take place and cannot be avoided. In the paper a new hydrodynamic sewer network modelling approach will be presented, which includes--besides precipitation--hydrographs of groundwater and surface water as essential boundary conditions. The concept of the modelling approach and the models to describe the infiltration, inflow and exfiltration fluxes are described. The model application to the sewerage system of the City of Dresden during a flood event with complex conditions shows that the processes of infiltration, exfiltration and surface water inflows can be described with a higher reliability and accuracy, showing that surface water inflow causes a pronounced system reaction. Further, according to the simulation results, a high sensitivity of exfiltration rates on the in-sewer water levels and a relatively low influence of the dynamic conditions on the infiltration rates were found.

Noncontact Monitoring of Respiration by Dynamic Air-Pressure Sensor.

PubMed

Takarada, Tohru; Asada, Tetsunosuke; Sumi, Yoshihisa; Higuchi, Yoshinori

2015-01-01

We have previously reported that a dynamic air-pressure sensor system allows respiratory status to be visually monitored for patients in minimally clothed condition. The dynamic air-pressure sensor measures vital information using changes in air pressure. To utilize this device in the field, we must clarify the influence of clothing conditions on measurement. The present study evaluated use of the dynamic air-pressure sensor system as a respiratory monitor that can reliably detect change in breathing patterns irrespective of clothing. Twelve healthy volunteers reclined on a dental chair positioned horizontally with the sensor pad for measuring air-pressure signals corresponding to respiration placed on the seat back of the dental chair in the central lumbar region. Respiratory measurements were taken under 2 conditions: (a) thinly clothed (subject lying directly on the sensor pad); and (b) thickly clothed (subject lying on the sensor pad covered with a pressure-reducing sheet). Air-pressure signals were recorded and time integration values for air pressure during each expiration were calculated. This information was compared with expiratory tidal volume measured simultaneously by a respirometer connected to the subject via face mask. The dynamic air-pressure sensor was able to receive the signal corresponding to respiration regardless of clothing conditions. A strong correlation was identified between expiratory tidal volume and time integration values for air pressure during each expiration for all subjects under both clothing conditions (0.840-0.988 for the thinly clothed condition and 0.867-0.992 for the thickly clothed condition). These results show that the dynamic air-pressure sensor is useful for monitoring respiratory physiology irrespective of clothing.

Mesoscale mixing of the Denmark Strait Overflow in the Irminger Basin

NASA Astrophysics Data System (ADS)

Koszalka, Inga M.; Haine, Thomas W. N.; Magaldi, Marcello G.

2017-04-01

The Denmark Strait Overflow (DSO) is a major export route for dense waters from the Nordic Seas forming the lower limb of the Atlantic Meridional Overturning Circulation, an important element of the climate system. Mixing processes along the DSO pathway influence its volume transport and properties contributing to the variability of the deep overturning circulation. They are poorly sampled by observations, however, which hinders development of a proper DSO representation in global circulation models. We employ a high resolution regional ocean model of the Irminger Basin to quantify impact of the mesoscale flows on DSO mixing focusing on geographical localization and the time-modulation of water property changes. The model reproduces the observed bulk warming of the DSO plume 100-200 km downstream of the Denmark Strait sill. It also reveals that mesoscale variability of the overflow ('DSO-eddies', of 20-30 km extent and a time scale of 2-5 day) modulates water property changes and turbulent mixing, diagnosed with the vertical shear of horizontal velocity and the eddy heat flux divergence. The space-time localization of the DSO mixing and warming and the role of coherent mesoscale structures should be explored by turbulence measurements and factored into the coarse circulation models.

Recent Progress on the Parallel Implementation of Moving-Body Overset Grid Schemes

NASA Technical Reports Server (NTRS)

Wissink, Andrew; Allen, Edwin (Technical Monitor)

1998-01-01

Viscous calculations about geometrically complex bodies in which there is relative motion between component parts is one of the most computationally demanding problems facing CFD researchers today. This presentation documents results from the first two years of a CHSSI-funded effort within the U.S. Army AFDD to develop scalable dynamic overset grid methods for unsteady viscous calculations with moving-body problems. The first pan of the presentation will focus on results from OVERFLOW-D1, a parallelized moving-body overset grid scheme that employs traditional Chimera methodology. The two processes that dominate the cost of such problems are the flow solution on each component and the intergrid connectivity solution. Parallel implementations of the OVERFLOW flow solver and DCF3D connectivity software are coupled with a proposed two-part static-dynamic load balancing scheme and tested on the IBM SP and Cray T3E multi-processors. The second part of the presentation will cover some recent results from OVERFLOW-D2, a new flow solver that employs Cartesian grids with various levels of refinement, facilitating solution adaption. A study of the parallel performance of the scheme on large distributed- memory multiprocessor computer architectures will be reported.

Water quality deterioration at a karst spring (Gallusquelle, Germany) due to combined sewer overflow: evidence of bacterial and micro-pollutant contamination

NASA Astrophysics Data System (ADS)

Heinz, B.; Birk, S.; Liedl, R.; Geyer, T.; Straub, K. L.; Andresen, J.; Bester, K.; Kappler, A.

2009-04-01

The concurrent use of karst aquifers as drinking water resources and receptors of combined sewer overflow lacking appropriate pre-treatment may cause conflicts between drinking water supply and storm water management. A storm water tank (SWT) for combined wastewater is identified as the source of sporadic contamination of a karst spring (Gallusquelle, “Schwäbische Alb”, SW Germany) used for public water supply. Spring water quality was examined by routine and event sampling and by evaluating physicochemical and microbiological parameters. The total number of microbial colonies growing at 20°C and the number of Escherichia coli colonies rose to values up to four orders of magnitude higher than background, 2-5 days after overflow of the SWT. High concentrations of chloride, sodium, and total organic carbon (TOC) and high values of turbidity coincide with this increase. However, high bacterial contamination is also observed while turbidity and TOC are low. Several wastewater-related organic micro-pollutants such as chlorinated and non-chlorinated organophosphates were detected in the SWT and, depending on their K ow values and their biodegradability, in lower concentrations at the spring.

Reducing CSOs and giving the river back to the public: innovative combined sewer overflow control and riverbanks restoration of the St. Charles River in Quebec City.

PubMed

Fradet, Olivier; Pleau, Martin; Marcoux, Christiane

2011-01-01

After the construction of its wastewater treatment plants, the City of Quebec began to implement overflow control in wet weather to ultimately meet the effluent discharge objectives, i.e. no more than two overflows per summer season in the St. Lawrence River and no more than four in the St-Charles River. After several years of studies to determine which management strategies would best suit the purpose, and to propose optimum solutions, a first project to implement optimal and predictive management in real time, called "Pilot", came to life in 1999. Construction in phases soon followed and the work was completed in the fall of 2009. As a result, requirements with regard to environmental rejects were met in two sectors, namely the St-Charles River and the Jacques-Cartier Beach, and aquatic recreational activities could resume. Meanwhile, the City also worked at giving back access to the water courses to the public by developing sites at the Jacques-Cartier Beach and in the Bay of Beauport, and by rehabilitating the banks of the St-Charles River.

Technologies for Fire and Damage Control and Condition Based Maintenance

DTIC Science & Technology

2011-12-01

sheathing, thermal and acoustic insulation, furnishing, bedding, mattresses, flooring , and wood fibre (paper and cardboard) and plastic packaging...Condition Based Maintenance”. The project objective was to develop an improved understanding of how materials, sensors and sensor systems choices impact the...ultraviolet spectral sensors and an acoustic sensor. The system also has data fusion software that analyses the sensor input and determines if the input

Sensor Technology Baseline Study for Enabling Condition Based Maintenance Plus in Army Ground Vehicles

DTIC Science & Technology

2012-03-01

for enabling condition based maintenance plus in Army ground vehicles. The sensor study was driven from Failure Mode Effects Analysis ( FMEA ...of Tables Table 1. Sensor technology baseline study based on engine FMEA report. ...................................5 Table 2. Sensor technology...baseline study based on transmission FMEA report. .........................8 Table 3. Sensor technology baseline study based on alternator FMEA report

Evaporometer | A Wireless Mesh of Open-Source Rainfall/Evaporation Gauge and Sensor Suite for In Situ Near-Real-Time Environmental Data

NASA Astrophysics Data System (ADS)

Kwon, M.; Lopez Alcala, J. M.; DeBell, T. C.; Udell, C.; Selker, J. S.

2017-12-01

Access to in situ near real-time environmental sensor data in remote locations provides invaluable utility in the fields of agricultural and environmental sciences. For studies where data needs to be gathered frequently, it could be costly and dangerous to take numerous trips into the field to collect this information and to inspect multitudes of distributed devices to ensure proper operation. One solution is to develop remote sensors capable of transmitting data and status updates (like battery level) over long distances from unserviced locations to a receiver hub to be accessed in near real-time online. The Openly Published Environmental Sensing Lab at Oregon State University (OPEnS Lab) produced a low-cost Open Source environmental sensing station called the Evaporometer that collects data at precisely timed intervals including rainfall amount, rate of evaporation, temperature, humidity and light (IR and Visible spectra), while CO2 and other sensors are also being evaluated for inclusion. This project focuses on the development and deployment of the prototype Evaporometer in HJ Andrew's Experimental Forest located in Blue River Oregon. The Evaporometer was designed for efficiency and succeeds in systematically collecting environmental data in hard to reach places over long periods of time. A real time clock interrupt enables the device to enter and exit "sleep mode", allowing Evaporometers to remain in the field over long periods of time and controlling the how frequently data should be collected. A load cell measures the weight of collected water in a container. This container is tightly packed with a fiberglass wick, which draws water from the bottom to the surface for efficient evaporation. A siphon has been designed into the container to prevent any possible water overflow situations and lost collected rainfall. All data collection and transmission processes are handled by an Adafruit Feather development board equipped with a long range, low power wireless (LoRa) radio that sends encrypted data via 900MHz ISM band. This data can be transmitted up to 20km to a receiver hub with an internet connection, and uploaded directly to Google cloud storage or other online data services for convenience.

An Approach for Rapid Assessment of Seismic Hazards in Turkey by Continuous GPS Data

PubMed Central

Ozener, Haluk; Dogru, Asli; Unlutepe, Ahmet

2009-01-01

The Earth is being monitored every day by all kinds of sensors. This leads an overflow of data in all branches of science nowadays, especially in Earth Sciences. Data storage and data processing are the problems to be solved by current technologies, as well as by those accessing and analyzing these large data sources. Once solutions have been created for collecting, storing and accessing data, then the challenge becomes how to effectively share data, applications and processing resources across many locations. The Global Positioning System (GPS) sensors are being used as geodetic instruments to precisely detect crustal motion in the Earth's surface. Rapid access to data provided by GPS sensors is becoming increasingly important for deformation monitoring and rapid hazard assessments. Today, reliable and fast collection and distribution of data is a challenge and advances in Internet technologies have made it easier to provide the needed data. This study describes a system which will be able to generate strain maps using data from continuous GPS stations for seismic hazard analysis. Strain rates are a key factor in seismic hazard analyses. Turkey is a country prone to earthquakes with a long history of seismic hazards and disasters. This situation has resulted in the studies by Earth scientists that focus on Turkey in order to improve their understanding of the Earth's crust structure and seismic hazards. Nevertheless, the construction of models, data access and analysis are often not fast as expected, but the combination of Internet technologies with continuous GPS sensors can be a solution to overcome this problem. This system would have the potential to answer many important questions to assess seismic hazards such as how much stretching, squashing and shearing is taking place in different parts of Turkey, and how do velocities change from place to place? Seismic hazard estimation is the most effective way to reduce earthquake losses. It is clear that reliability of data and on-line services will support the preparation of strategies for disaster management and planning to cope with hazards. PMID:22389619

Advanced haptic sensor for measuring human skin conditions

NASA Astrophysics Data System (ADS)

Tsuchimi, Daisuke; Okuyama, Takeshi; Tanaka, Mami

2009-12-01

This paper is concerned with the development of a tactile sensor using PVDF (Polyvinylidene Fluoride) film as a sensory receptor of the sensor to evaluate softness, smoothness, and stickiness of human skin. Tactile sense is the most important sense in the sensation receptor of the human body along with eyesight, and we can examine skin condition quickly using these sense. But, its subjectivity and ambiguity make it difficult to quantify skin conditions. Therefore, development of measurement device which can evaluate skin conditions easily and objectively is demanded by dermatologists, cosmetic industries, and so on. In this paper, an advanced haptic sensor system that can measure multiple information of skin condition in various parts of human body is developed. The applications of the sensor system to evaluate softness, smoothness, and stickiness of skin are investigated through two experiments.

Advanced haptic sensor for measuring human skin conditions

NASA Astrophysics Data System (ADS)

Tsuchimi, Daisuke; Okuyama, Takeshi; Tanaka, Mami

2010-01-01

This paper is concerned with the development of a tactile sensor using PVDF (Polyvinylidene Fluoride) film as a sensory receptor of the sensor to evaluate softness, smoothness, and stickiness of human skin. Tactile sense is the most important sense in the sensation receptor of the human body along with eyesight, and we can examine skin condition quickly using these sense. But, its subjectivity and ambiguity make it difficult to quantify skin conditions. Therefore, development of measurement device which can evaluate skin conditions easily and objectively is demanded by dermatologists, cosmetic industries, and so on. In this paper, an advanced haptic sensor system that can measure multiple information of skin condition in various parts of human body is developed. The applications of the sensor system to evaluate softness, smoothness, and stickiness of skin are investigated through two experiments.

System and method for diagnosing EGR performance using NOx sensor

DOEpatents

Mazur, Christopher John

2003-12-23

A method and system for diagnosing a condition of an EGR valve used in an engine system. The EGR valve controls the portion exhaust gases produced by such engine system and fed back to an intake of such engine system. The engine system includes a NOx sensor for measuring NOx in such exhaust. The method includes: determining a time rate of change in NOx measured by the NOx sensor; comparing the determined time rate of change in the measured NOx with a predetermined expected time rate of change in measured NOx; and determining the condition of the EGR valve as a function of such comparison. The method also includes: determining from NOx measured by the NOx sensor and engine operating conditions indications of instances when samples of such measured NOx are greater than an expected maximum NOx level for such engine condition and less than an expected minimum NOx level for such engine condition; and determining the condition of the EGR valve as a function of a statistical analysis of such indications. The method includes determining whether the NOx sensor is faulty and wherein the EGR condition determining includes determining whether the NOx sensor is faulty.

Effective Sensor Selection and Data Anomaly Detection for Condition Monitoring of Aircraft Engines

PubMed Central

Liu, Liansheng; Liu, Datong; Zhang, Yujie; Peng, Yu

2016-01-01

In a complex system, condition monitoring (CM) can collect the system working status. The condition is mainly sensed by the pre-deployed sensors in/on the system. Most existing works study how to utilize the condition information to predict the upcoming anomalies, faults, or failures. There is also some research which focuses on the faults or anomalies of the sensing element (i.e., sensor) to enhance the system reliability. However, existing approaches ignore the correlation between sensor selecting strategy and data anomaly detection, which can also improve the system reliability. To address this issue, we study a new scheme which includes sensor selection strategy and data anomaly detection by utilizing information theory and Gaussian Process Regression (GPR). The sensors that are more appropriate for the system CM are first selected. Then, mutual information is utilized to weight the correlation among different sensors. The anomaly detection is carried out by using the correlation of sensor data. The sensor data sets that are utilized to carry out the evaluation are provided by National Aeronautics and Space Administration (NASA) Ames Research Center and have been used as Prognostics and Health Management (PHM) challenge data in 2008. By comparing the two different sensor selection strategies, the effectiveness of selection method on data anomaly detection is proved. PMID:27136561

Effective Sensor Selection and Data Anomaly Detection for Condition Monitoring of Aircraft Engines.

PubMed

Liu, Liansheng; Liu, Datong; Zhang, Yujie; Peng, Yu

2016-04-29

In a complex system, condition monitoring (CM) can collect the system working status. The condition is mainly sensed by the pre-deployed sensors in/on the system. Most existing works study how to utilize the condition information to predict the upcoming anomalies, faults, or failures. There is also some research which focuses on the faults or anomalies of the sensing element (i.e., sensor) to enhance the system reliability. However, existing approaches ignore the correlation between sensor selecting strategy and data anomaly detection, which can also improve the system reliability. To address this issue, we study a new scheme which includes sensor selection strategy and data anomaly detection by utilizing information theory and Gaussian Process Regression (GPR). The sensors that are more appropriate for the system CM are first selected. Then, mutual information is utilized to weight the correlation among different sensors. The anomaly detection is carried out by using the correlation of sensor data. The sensor data sets that are utilized to carry out the evaluation are provided by National Aeronautics and Space Administration (NASA) Ames Research Center and have been used as Prognostics and Health Management (PHM) challenge data in 2008. By comparing the two different sensor selection strategies, the effectiveness of selection method on data anomaly detection is proved.

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines

PubMed Central

Xu, Jingjing; Yang, Wei; Zhang, Linyuan; Han, Ruisong; Shao, Xiaotao

2015-01-01

In this paper, a wireless sensor network (WSN) technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA) to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI) arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD) algorithm with particle swarm optimization (PSO), namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER) performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization. PMID:26343660

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines.

PubMed

Xu, Jingjing; Yang, Wei; Zhang, Linyuan; Han, Ruisong; Shao, Xiaotao

2015-08-27

In this paper, a wireless sensor network (WSN) technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA) to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI) arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD) algorithm with particle swarm optimization (PSO), namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER) performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

Quantification of a contact stimulus by diapers

NASA Astrophysics Data System (ADS)

Nomata, Takuya; Okuyama, Takeshi; Teraoka, Hiromi; Murakami, Yasuo; Miyazawa, Kiyoshi; Tanaka, Mami

2010-01-01

This paper describes a development of a sensor system for measurement of a contact stimulus which diapers give to infants. A polyvinyliden fluoride (PVDF) film and a strain gauge are used as the sensor receptors. The PVDF is a kind of piezoelectric material. The sensor consists of a surface contact layer, a PVDF film, a strain gauge and an aluminum plate. First, in order to investigate the sensor performance, the sensor was located on a silicone plate and the upper part of the sensor was rubbed with an acrylic artificial finger. The finger enabled the measurement to carry out at a constant speed and force. Next, the sensor was attached on an infant dummy and the sensor outputs were measured under conditions with and without diapers. By comparison of the output under two different conditions, it was confirmed that there is a clearly difference between the two conditions. It was found that the developed sensor system has the possibility to quantify a contact stimulus which diapers give infants.

Quantification of a contact stimulus by diapers

NASA Astrophysics Data System (ADS)

Nomata, Takuya; Okuyama, Takeshi; Teraoka, Hiromi; Murakami, Yasuo; Miyazawa, Kiyoshi; Tanaka, Mami

2009-12-01

This paper describes a development of a sensor system for measurement of a contact stimulus which diapers give to infants. A polyvinyliden fluoride (PVDF) film and a strain gauge are used as the sensor receptors. The PVDF is a kind of piezoelectric material. The sensor consists of a surface contact layer, a PVDF film, a strain gauge and an aluminum plate. First, in order to investigate the sensor performance, the sensor was located on a silicone plate and the upper part of the sensor was rubbed with an acrylic artificial finger. The finger enabled the measurement to carry out at a constant speed and force. Next, the sensor was attached on an infant dummy and the sensor outputs were measured under conditions with and without diapers. By comparison of the output under two different conditions, it was confirmed that there is a clearly difference between the two conditions. It was found that the developed sensor system has the possibility to quantify a contact stimulus which diapers give infants.

Comparison of Three Soil Moisture Sensor Types Under Field Conditions Based on the Marena, Oklahoma, In Situ Sensor Testbed (MOISST)

NASA Astrophysics Data System (ADS)

Zhang, N.; Quiring, S. M.; Ochsner, T. E.

2017-12-01

Each soil moisture monitoring network commonly adopts different sensor technologies. This results in different measurement units, depths and impedes large-scale soil moisture applications that seek to integrate data from multiple networks. Therefore, a comprehensive comparison of different sensors to identify the best approach for integrating and homogenizing measurements from different sensors is required. This study compares three commonly used sensors, including Stevens Water Hydra Probes, Campbell Scientific CS616 TDR and CS 229-L heat dissipation sensors based on data from May 2010 to December 2012 from the Marena, Oklahoma, In Situ Sensor Testbed (MOISST). All sensors are installed at common depths of 5, 10, 20, 50, 100 cm. The results reveal that the differences between the three sensors tends to increase with depth. The CDF plots showed CS 229 is most sensitive to moisture variation in dry condition and most easily saturated in wet condition, followed by Hydra probe and CS616. Our results show that calculating percentiles is a good normalization method for standardizing measurements from different sensors. Our preliminary results demonstrate that CDF matching can be used to convert measurements from one sensor to another.

Harsh Environment Silicon Carbide Sensor Technology for Geothermal Instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pisano, Albert P.

2013-04-26

This project utilizes Silicon Carbide (SiC) materials platform to fabricate advanced sensors to be used as high-temperature downhole instrumentation for the DOE’s Geothermal Technologies Program on Enhanced Geothermal Systems. The scope of the proposed research is to 1) develop a SiC pressure sensor that can operate in harsh supercritical conditions, 2) develop a SiC temperature sensor that can operate in harsh supercritical conditions, 3) develop a bonding process for adhering SiC sensor die to well casing couplers, and 4) perform experimental exposure testing of sensor materials and the sensor devices.

Effects of rainfall events on the occurrence and detection efficiency of viruses in river water impacted by combined sewer overflows.

PubMed

Hata, Akihiko; Katayama, Hiroyuki; Kojima, Keisuke; Sano, Shoichi; Kasuga, Ikuro; Kitajima, Masaaki; Furumai, Hiroaki

2014-01-15

Rainfall events can introduce large amount of microbial contaminants including human enteric viruses into surface water by intermittent discharges from combined sewer overflows (CSOs). The present study aimed to investigate the effect of rainfall events on viral loads in surface waters impacted by CSO and the reliability of molecular methods for detection of enteric viruses. The reliability of virus detection in the samples was assessed by using process controls for virus concentration, nucleic acid extraction and reverse transcription (RT)-quantitative PCR (qPCR) steps, which allowed accurate estimation of virus detection efficiencies. Recovery efficiencies of poliovirus in river water samples collected during rainfall events (<10%) were lower than those during dry weather conditions (>10%). The log10-transformed virus concentration efficiency was negatively correlated with suspended solid concentration (r(2)=0.86) that increased significantly during rainfall events. Efficiencies of DNA extraction and qPCR steps determined with adenovirus type 5 and a primer sharing control, respectively, were lower in dry weather. However, no clear relationship was observed between organic water quality parameters and efficiencies of these two steps. Observed concentrations of indigenous enteric adenoviruses, GII-noroviruses, enteroviruses, and Aichi viruses increased during rainfall events even though the virus concentration efficiency was presumed to be lower than in dry weather. The present study highlights the importance of using appropriate process controls to evaluate accurately the concentration of water borne enteric viruses in natural waters impacted by wastewater discharge, stormwater, and CSOs. © 2013.

Evaluation of sensor arrays for engine oils using artificial oil alteration

NASA Astrophysics Data System (ADS)

Sen, Sedat; Schneidhofer, Christoph; Dörr, Nicole; Vellekoop, Michael J.

2011-06-01

With respect to varying operation conditions, only sensors directly installed in the engine can detect the current oil condition hence enabling to get the right time for the oil change. Usually, only one parameter is not sufficient to obtain reliable information about the current oil condition. For this reason, appropriate sensor principles were evaluated for the design of sensor arrays for the measurement of critical lubricant parameters. In this contribution, we report on the development of a sensor array for engine oils using laboratory analyses of used engine oils for the correlation with sensor signals. The sensor array comprises the measurement of conductivity, permittivity, viscosity and temperature as well as oil corrosiveness as a consequence of acidification of the lubricant. As a key method, rapid evaluation of the sensors was done by short term simulation of entire oil change intervals based on artificial oil alteration. Thereby, the compatibility of the sensor array to the lubricant and the oil deterioration during the artificial alteration process was observed by the sensors and confirmed by additional laboratory analyses of oil samples take.

Singularity-free extraction of a quaternion from a direction-cosine matrix. [for spacecraft control and guidance

NASA Technical Reports Server (NTRS)

Klumpp, A. R.

1976-01-01

A computer algorithm for extracting a quaternion from a direction-cosine matrix (DCM) is described. The quaternion provides a four-parameter representation of rotation, as against the nine-parameter representation afforded by a DCM. Commanded attitude in space shuttle steering is conveniently computed by DCM, while actual attitude is computed most compactly as a quaternion, as is attitude error. The unit length of the rotation quaternion, and interchangeable of a quaternion and its negative, are used to advantage in the extraction algorithm. Protection of the algorithm against square root failure and division overflow are considered. Necessary and sufficient conditions for handling the rotation vector element of largest magnitude are discussed

Category-theoretic models of algebraic computer systems

NASA Astrophysics Data System (ADS)

Kovalyov, S. P.

2016-01-01

A computer system is said to be algebraic if it contains nodes that implement unconventional computation paradigms based on universal algebra. A category-based approach to modeling such systems that provides a theoretical basis for mapping tasks to these systems' architecture is proposed. The construction of algebraic models of general-purpose computations involving conditional statements and overflow control is formally described by a reflector in an appropriate category of algebras. It is proved that this reflector takes the modulo ring whose operations are implemented in the conventional arithmetic processors to the Łukasiewicz logic matrix. Enrichments of the set of ring operations that form bases in the Łukasiewicz logic matrix are found.

Solids precipitation and polymerization of asphaltenes in coal-derived liquids

DOEpatents

Kydd, Paul H.

1984-01-01

The precipitation and removal of particulate solids from coal-derived liquids by adding a process-derived anti-solvent liquid fraction and continuing the precipitation process at a temperature above the melting point of the mixed liquids for sufficient time to allow the asphaltenes to polymerize and solids to settle at atmospheric pressure conditions. The resulting clarified light hydrocarbon overflow liquid contains less than about 0.02 W % ash and is suitable as turbine fuel or as boiler fuel for burning without particulate emission control equipment. An underflow liquid fraction containing less than about 0.1 W % solids along with low sulfur and nitrogen concentrations is suitable as a boiler fuel with emission control equipment.

The influence of biodegradability of sewer solids for the management of CSOs.

PubMed

Sakrabani, R; Ashley, R M; Vollertsen, J

2005-01-01

The re-suspension of sediments in combined sewers and the associated pollutants into the bulk water during wet weather flows can cause pollutants to be carried further downstream to receiving waters or discharged via Combined Sewer Overflows (CSO). A typical pollutograph shows the trend of released bulk pollutants with time but does not consider information on the biodegradability of these pollutants. A new prediction methodology based on Oxygen Utilisation Rate (respirometric method) and Erosionmeter (laboratory device replicating in-sewer erosion) experiments is proposed which is able to predict the trends in biodegradability during in-sewer sediment erosion in wet weather conditions. The proposed new prediction methodology is also based on COD fractionation techniques.

A context-specific latent inhibition effect in a human conditioned suppression task.

PubMed

Byron Nelson, James; del Carmen Sanjuan, Maria

2006-06-01

Three studies used a computer video game preparation to demonstrate latent inhibition in adult humans. In all studies participants fired torpedoes at a target spaceship by clicking the mouse. Conditioned stimuli (CSs) were presented in the form of coloured "sensors" at the bottom of the screen. Conditioning was conducted by pairing a sensor with an attack from the target spaceship. Participants learned to suppress their rate of mouse clicking in preparation for an attack. In Experiment 1 a total of 10 preexposures to the sensor CS, prior to conditioning, retarded acquisition of suppression. In Experiment 2 the effect of preexposure was shown to be context specific. Experiment 3 showed little generalization of the preexposure effect from one sensor CS to another. Experiment 3 also showed that preexposure did not make the sensor CS inhibitory. Comparisons with conditioned suppression procedures with animals and negative-priming procedures are briefly discussed.

Technology review: prototyping platforms for monitoring ambient conditions.

PubMed

Afolaranmi, Samuel Olaiya; Ramis Ferrer, Borja; Martinez Lastra, Jose Luis

2018-05-08

The monitoring of ambient conditions in indoor spaces is very essential owing to the amount of time spent indoors. Specifically, the monitoring of air quality is significant because contaminated air affects the health, comfort and productivity of occupants. This research work presents a technology review of prototyping platforms for monitoring ambient conditions in indoor spaces. It involves the research on sensors (for CO 2 , air quality and ambient conditions), IoT platforms, and novel and commercial prototyping platforms. The ultimate objective of this review is to enable the easy identification, selection and utilisation of the technologies best suited for monitoring ambient conditions in indoor spaces. Following the review, it is recommended to use metal oxide sensors, optical sensors and electrochemical sensors for IAQ monitoring (including NDIR sensors for CO 2 monitoring), Raspberry Pi for data processing, ZigBee and Wi-Fi for data communication, and ThingSpeak IoT platform for data storage, analysis and visualisation.

CFD Predictions for Transonic Performance of the ERA Hybrid Wing-Body Configuration

NASA Technical Reports Server (NTRS)

Deere, Karen A.; Luckring, James M.; McMillin, S. Naomi; Flamm, Jeffrey D.; Roman, Dino

2016-01-01

A computational study was performed for a Hybrid Wing Body configuration that was focused at transonic cruise performance conditions. In the absence of experimental data, two fully independent computational fluid dynamics analyses were conducted to add confidence to the estimated transonic performance predictions. The primary analysis was performed by Boeing with the structured overset-mesh code OVERFLOW. The secondary analysis was performed by NASA Langley Research Center with the unstructured-mesh code USM3D. Both analyses were performed at full-scale flight conditions and included three configurations customary to drag buildup and interference analysis: a powered complete configuration, the configuration with the nacelle/pylon removed, and the powered nacelle in isolation. The results in this paper are focused primarily on transonic performance up to cruise and through drag rise. Comparisons between the CFD results were very good despite some minor geometric differences in the two analyses.

A procedure for automating CFD simulations of an inlet-bleed problem

NASA Technical Reports Server (NTRS)

Chyu, Wei J.; Rimlinger, Mark J.; Shih, Tom I.-P.

1995-01-01

A procedure was developed to improve the turn-around time for computational fluid dynamics (CFD) simulations of an inlet-bleed problem involving oblique shock-wave/boundary-layer interactions on a flat plate with bleed into a plenum through one or more circular holes. This procedure is embodied in a preprocessor called AUTOMAT. With AUTOMAT, once data for the geometry and flow conditions have been specified (either interactively or via a namelist), it will automatically generate all input files needed to perform a three-dimensional Navier-Stokes simulation of the prescribed inlet-bleed problem by using the PEGASUS and OVERFLOW codes. The input files automatically generated by AUTOMAT include those for the grid system and those for the initial and boundary conditions. The grid systems automatically generated by AUTOMAT are multi-block structured grids of the overlapping type. Results obtained by using AUTOMAT are presented to illustrate its capability.

Fingerprint enhancement using a multispectral sensor

NASA Astrophysics Data System (ADS)

Rowe, Robert K.; Nixon, Kristin A.

2005-03-01

The level of performance of a biometric fingerprint sensor is critically dependent on the quality of the fingerprint images. One of the most common types of optical fingerprint sensors relies on the phenomenon of total internal reflectance (TIR) to generate an image. Under ideal conditions, a TIR fingerprint sensor can produce high-contrast fingerprint images with excellent feature definition. However, images produced by the same sensor under conditions that include dry skin, dirt on the skin, and marginal contact between the finger and the sensor, are likely to be severely degraded. This paper discusses the use of multispectral sensing as a means to collect additional images with new information about the fingerprint that can significantly augment the system performance under both normal and adverse sample conditions. In the context of this paper, "multispectral sensing" is used to broadly denote a collection of images taken under different illumination conditions: different polarizations, different illumination/detection configurations, as well as different wavelength illumination. Results from three small studies using an early-stage prototype of the multispectral-TIR (MTIR) sensor are presented along with results from the corresponding TIR data. The first experiment produced data from 9 people, 4 fingers from each person and 3 measurements per finger under "normal" conditions. The second experiment provided results from a study performed to test the relative performance of TIR and MTIR images when taken under extreme dry and dirty conditions. The third experiment examined the case where the area of contact between the finger and sensor is greatly reduced.

CFD Based Computations of Flexible Helicopter Blades for Stability Analysis

NASA Technical Reports Server (NTRS)

Guruswamy, Guru P.

2011-01-01

As a collaborative effort among government aerospace research laboratories an advanced version of a widely used computational fluid dynamics code, OVERFLOW, was recently released. This latest version includes additions to model flexible rotating multiple blades. In this paper, the OVERFLOW code is applied to improve the accuracy of airload computations from the linear lifting line theory that uses displacements from beam model. Data transfers required at every revolution are managed through a Unix based script that runs jobs on large super-cluster computers. Results are demonstrated for the 4-bladed UH-60A helicopter. Deviations of computed data from flight data are evaluated. Fourier analysis post-processing that is suitable for aeroelastic stability computations are performed.

OVERFLOW ROADLESS AREA, GEORGIA AND NORTH CAROLINA.

USGS Publications Warehouse

Koeppen, Robert P.; Davis, Michael P.

1984-01-01

The Overflow Roadless Area in the Blue Ridge Mountains of Georgia and North Carolina is underlain by complexly folded schist and gneiss of Proterozoic age. A mineral-resource survey found little likelihood for the occurrence of mineral or energy resources in the area. Minor isolated localities of mica pegmatite and amethyst gemstone occur in the area. Gneiss and schist suitable for rock aggregate are present in large quantities, but similar rocks abound outside the area. Natural gas may possibly be present at great depth beneath the overthrust of the Blue Ridge. Further seismic studies and exploratory drilling are needed to evaluate the natural gas potential of this part of the Eastern Overthrust Belt.

Fast Plasma Investigation for MMS: Simulation of the Burst Triggering System

NASA Technical Reports Server (NTRS)

Barrie, A. C.; Dorelli, J. C.; Winkert, G. E.; Lobell, J. V.; Holland, M. P.; Adrian, M. L.; Pollock, C. J.

2011-01-01

The Magnetospheric Multiscale (MMS) mission will study small-scale reconnection structures and their rapid motions from closely spaced platforms using instruments capable of high angular, energy, and time resolution measurements. To meet these requirements, the Fast Plasma Instrument (FPI) consists of eight (8) identical half top-hat electron sensors and eight (8) identical ion sensors and an Instrument Data Processing Unit (IDPU). The sensors (electron or ion) are grouped into pairs whose 6 degree x 180 degree fields-of-view (FOV) are set 90 degrees apart. Each sensor is equipped with electrostatic aperture steering to allow the sensor to scan a 45 degree x 180 degree fan about the its nominal viewing (0 deflection) direction. Each pair of sensors, known as the Dual Electron Spectrometer (DES) and the Dual Ion Spectrometer (DIS), occupies a quadrant on the MMS spacecraft and the combination of the eight electron/ion sensors, employing aperture steering, image the full-sky every 30-ms (electrons) and 150-ms (ions), respectively. To probe the diffusion regions of reconnection, the highest temporal/spatial resolution mode of FPI results in the DES complement of a given spacecraft generating 6.5-Mb (raised dot) per second of electron data while the DIS generates 1.1-Mb (raised dot) per second of ion data yielding an FPI total data rate of 6.6-Mb (raised dot) per second. The FPI electron/ion data is collected by the IDPU then transmitted to the Central Data Instrument Processor (CIDP) on the spacecraft for science interest ranking. Only data sequences that contain the greatest amount of temporal/spatial structure will be intelligently down-linked by the spacecraft. This requires a data ranking process known as the burst trigger system. The burst trigger system uses pseudo physical quantities to approximate the local plasma environments. As each pseudo quantity will have a different value, a set of two scaling factors is employed for each pseudo term. These pseudo quantities are then combined at the instrument, spacecraft, and observatory level leading to a final ranking of data based on expected scientific interest. Here, we present simulations of the fixed point burst trigger system for the FPI. A variety of data sets based on previous mission data as well as analytical formulations are tested. Comparisons of floating point calculations versus the fixed point hardware simulation are shown. Analysis of the potential sources of error from overflows, quantization, etc. are examined and mitigation methods are presented. Finally a series of calibration curves are presented, showing the expected error in pseudo quantities based solely on the scale parameters chosen and the expected data range. We conclude with a presentation of the current base-lined FPI burst trigger approach.

A Novel Concrete-Based Sensor for Detection of Ice and Water on Roads and Bridges

PubMed Central

Aljuboori, Mohammed

2017-01-01

Hundreds of people are killed or injured annually in the United States in accidents related to ice formation on roadways and bridge decks. In this paper, a novel embedded sensor system is proposed for the detection of black ice as well as wet, dry, and frozen pavement conditions on roads, runways, and bridges. The proposed sensor works by detecting changes in electrical resistance between two sets of stainless steel poles embedded in the concrete sensor to assess surface and near-surface conditions. A preliminary decision algorithm is developed that utilizes sensor outputs indicating resistance changes and surface temperature. The sensor consists of a 102-mm-diameter, 38-mm-high, concrete cylinder. Laboratory results indicate that the proposed sensor can effectively detect surface ice and wet conditions even in the presence of deicing chlorides and rubber residue. This sensor can further distinguish black ice from ice that may exist within concrete pores. PMID:29240710

Evaluation of Pressure Capacitive Sensors for Application in Grasping and Manipulation Analysis.

PubMed

Pessia, Paola; Cordella, Francesca; Schena, Emiliano; Davalli, Angelo; Sacchetti, Rinaldo; Zollo, Loredana

2017-12-08

The analysis of the human grasping and manipulation capabilities is paramount for investigating human sensory-motor control and developing prosthetic and robotic hands resembling the human ones. A viable solution to perform this analysis is to develop instrumented objects measuring the interaction forces with the hand. In this context, the performance of the sensors embedded in the objects is crucial. This paper focuses on the experimental characterization of a class of capacitive pressure sensors suitable for biomechanical analysis. The analysis was performed in three loading conditions (Distributed load, 9 Tips load, and Wave-shaped load, thanks to three different inter-elements) via a traction/compression testing machine. Sensor assessment was also carried out under human- like grasping condition by placing a silicon material with the same properties of prosthetic cosmetic gloves in between the sensor and the inter-element in order to simulate the human skin. Data show that the input-output relationship of the analyzed, sensor is strongly influenced by both the loading condition (i.e., type of inter-element) and the grasping condition (with or without the silicon material). This needs to be taken into account to avoid significant measurement error. To go over this hurdle, the sensors have to be calibrated under each specific condition in order to apply suitable corrections to the sensor output and significantly improve the measurement accuracy.

Evaluation of Pressure Capacitive Sensors for Application in Grasping and Manipulation Analysis

PubMed Central

Pessia, Paola; Cordella, Francesca; Davalli, Angelo; Sacchetti, Rinaldo; Zollo, Loredana

2017-01-01

The analysis of the human grasping and manipulation capabilities is paramount for investigating human sensory-motor control and developing prosthetic and robotic hands resembling the human ones. A viable solution to perform this analysis is to develop instrumented objects measuring the interaction forces with the hand. In this context, the performance of the sensors embedded in the objects is crucial. This paper focuses on the experimental characterization of a class of capacitive pressure sensors suitable for biomechanical analysis. The analysis was performed in three loading conditions (Distributed load, 9 Tips load, and Wave-shaped load, thanks to three different inter-elements) via a traction/compression testing machine. Sensor assessment was also carried out under human- like grasping condition by placing a silicon material with the same properties of prosthetic cosmetic gloves in between the sensor and the inter-element in order to simulate the human skin. Data show that the input–output relationship of the analyzed, sensor is strongly influenced by both the loading condition (i.e., type of inter-element) and the grasping condition (with or without the silicon material). This needs to be taken into account to avoid significant measurement error. To go over this hurdle, the sensors have to be calibrated under each specific condition in order to apply suitable corrections to the sensor output and significantly improve the measurement accuracy. PMID:29292717

Characterization of the effects of serotonin on the release of (/sup 3/H)dopamine from rat nucleus accumbens and striatal slices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nurse, B.; Russell, V.A.; Taljaard, J.J.

1988-05-01

The effect of serotonin agonists on the depolarization (K+)-induced, calcium-dependent, release of (/sup 3/H)dopamine (DA) from rat nucleus accumbens and striatal slices was investigated. Serotonin enhanced basal /sup 3/H overflow and reduced K+-induced release of (/sup 3/H)DA from nucleus accumbens slices. The effect of serotonin on basal /sup 3/H overflow was not altered by the serotonin antagonist, methysergide, or the serotonin re-uptake blocker, chlorimipramine, but was reversed by the DA re-uptake carrier inhibitors nomifensine and benztropine. With the effect on basal overflow blocked, serotonin did not modulate K+-induced release of (/sup 3/H)DA in the nucleus accumbens or striatum. The serotoninmore » agonists, quipazine (in the presence of nomifensine) and 5-methoxytryptamine, did not significantly affect K+-induced release of (/sup 3/H)DA in the nucleus accumbens. This study does not support suggestions that serotonin receptors inhibit the depolarization-induced release of dopamine in the nucleus accumbens or striatum of the rat brain. The present results do not preclude the possibility that serotonin may affect the mesolimbic reward system at a site which is post-synaptic to dopaminergic terminals in the nucleus accumbens.« less

Hydraulic characteristics of low-impact development practices in northeastern Ohio, 2008–2010

USGS Publications Warehouse

Darner, Robert A.; Dumouchelle, Denise H.

2011-01-01

Low-impact development (LID) is an approach to managing stormwater as near to its source as possible; this is accomplished by minimizing impervious surfaces and promoting more natural infiltration and evapotranspiration than is typically associated with developed areas. Two newly constructed LID sites in northeastern Ohio were studied to document their hydraulic characteristics. A roadside best-management practice (BMP) was constructed by replacing about 1,400 linear feet of existing ditches with a bioswale/rain garden BMP consisting of a grassed swale interspersed with rain-garden/overflow structures. The site was monitored in 2008, 2009, and 2010. Although some overflows occurred, numerous precipitation events exceeding the 0.75-inch design storm did not result in overflows. A second study site consists of an 8,200-square-foot parking lot made of a pervious pavers and a rain garden that receives runoff from the roof of a nearby commercial building. A comparison of data from 2009 and 2010 indicates that the median runoff volume in 2010 decreased relative to 2009. The centroid lag times (time difference between centroid of precipitation and centroid of flow) decreased in 2010, most likely due to more intense, shorter duration precipitation events and maturation of the rain garden. Additional data could help quantify the relation between meteorological variables and BMP efficiency.

OVERSMART Reporting Tool for Flow Computations Over Large Grid Systems

NASA Technical Reports Server (NTRS)

Kao, David L.; Chan, William M.

2012-01-01

Structured grid solvers such as NASA's OVERFLOW compressible Navier-Stokes flow solver can generate large data files that contain convergence histories for flow equation residuals, turbulence model equation residuals, component forces and moments, and component relative motion dynamics variables. Most of today's large-scale problems can extend to hundreds of grids, and over 100 million grid points. However, due to the lack of efficient tools, only a small fraction of information contained in these files is analyzed. OVERSMART (OVERFLOW Solution Monitoring And Reporting Tool) provides a comprehensive report of solution convergence of flow computations over large, complex grid systems. It produces a one-page executive summary of the behavior of flow equation residuals, turbulence model equation residuals, and component forces and moments. Under the automatic option, a matrix of commonly viewed plots such as residual histograms, composite residuals, sub-iteration bar graphs, and component forces and moments is automatically generated. Specific plots required by the user can also be prescribed via a command file or a graphical user interface. Output is directed to the user s computer screen and/or to an html file for archival purposes. The current implementation has been targeted for the OVERFLOW flow solver, which is used to obtain a flow solution on structured overset grids. The OVERSMART framework allows easy extension to other flow solvers.

Analyzing a 35-Year Hourly Data Record: Why So Difficult?

NASA Technical Reports Server (NTRS)

Lynnes, Chris

2014-01-01

At the Goddard Distributed Active Archive Center, we have recently added a 35-Year record of output data from the North American Land Assimilation System (NLDAS) to the Giovanni web-based analysis and visualization tool. Giovanni (Geospatial Interactive Online Visualization ANd aNalysis Infrastructure) offers a variety of data summarization and visualization to users that operate at the data center, obviating the need for users to download and read the data themselves for exploratory data analysis. However, the NLDAS data has proven surprisingly resistant to application of the summarization algorithms. Algorithms that were perfectly happy analyzing 15 years of daily satellite data encountered limitations both at the algorithm and system level for 35 years of hourly data. Failures arose, sometimes unexpectedly, from command line overflows, memory overflows, internal buffer overflows, and time-outs, among others. These serve as an early warning sign for the problems likely to be encountered by the general user community as they try to scale up to Big Data analytics. Indeed, it is likely that more users will seek to perform remote web-based analysis precisely to avoid the issues, or the need to reprogram around them. We will discuss approaches to mitigating the limitations and the implications for data systems serving the user communities that try to scale up their current techniques to analyze Big Data.

Sea-level rise impacts on the temporal and spatial variability of extreme water levels: A case study for St. Peter-Ording, Germany

NASA Astrophysics Data System (ADS)

Santamaria-Aguilar, S.; Arns, A.; Vafeidis, A. T.

2017-04-01

Both the temporal and spatial variability of storm surge water level (WL) curves are usually not taken into account in flood risk assessments as observational data are often scarce. In addition, sea-level rise (SLR) can further affect the variability of WLs. We analyze the temporal and spatial variability of the WL curve of 75 historical storm surge events that have been numerically simulated for St. Peter-Ording at the German North Sea coast, considering the effects induced by three SLR scenarios (RCP 4.5, RCP 8.5, and a RCP 8.5 high end scenario). We assess potential impacts of these scenarios on two parameters related to flooding: overflow volumes and fullness. Our results indicate that due to both the temporal and spatial variability of those events the resulting overflow volume can be two or even three times greater. We observe a steepening of the WL curve with an increase of the tidal range under the three SLR scenarios, although SLR induced effects are relatively higher for the RCP 4.5. The steepening of the WL curve with SLR produces a reduction of the fullness, but the changes in overflow volumes also depend on the magnitude of the storm surge event.

Dynamic gauge adjustment of high-resolution X-band radar data for convective rain storms: Model-based evaluation against measured combined sewer overflow

NASA Astrophysics Data System (ADS)

Borup, Morten; Grum, Morten; Linde, Jens Jørgen; Mikkelsen, Peter Steen

2016-08-01

Numerous studies have shown that radar rainfall estimates need to be adjusted against rain gauge measurements in order to be useful for hydrological modelling. In the current study we investigate if adjustment can improve radar rainfall estimates to the point where they can be used for modelling overflows from urban drainage systems, and we furthermore investigate the importance of the aggregation period of the adjustment scheme. This is done by continuously adjusting X-band radar data based on the previous 5-30 min of rain data recorded by multiple rain gauges and propagating the rainfall estimates through a hydraulic urban drainage model. The model is built entirely from physical data, without any calibration, to avoid bias towards any specific type of rainfall estimate. The performance is assessed by comparing measured and modelled water levels at a weir downstream of a highly impermeable, well defined, 64 ha urban catchment, for nine overflow generating rain events. The dynamically adjusted radar data perform best when the aggregation period is as small as 10-20 min, in which case it performs much better than static adjusted radar data and data from rain gauges situated 2-3 km away.

Mass-loss evolution of close-in exoplanets: Evaporation of hot Jupiters and the effect on population

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurokawa, H.; Nakamoto, T., E-mail: kurokawa@nagoya-u.jp

2014-03-01

During their evolution, short-period exoplanets may lose envelope mass through atmospheric escape owing to intense X-ray and extreme ultraviolet (XUV) radiation from their host stars. Roche-lobe overflow induced by orbital evolution or intense atmospheric escape can also contribute to mass loss. To study the effects of mass loss on inner planet populations, we calculate the evolution of hot Jupiters considering mass loss of their envelopes and thermal contraction. Mass loss is assumed to occur through XUV-driven atmospheric escape and the following Roche-lobe overflow. The runaway effect of mass loss results in a dichotomy of populations: hot Jupiters that retain theirmore » envelopes and super Earths whose envelopes are completely lost. Evolution primarily depends on the core masses of planets and only slightly on migration history. In hot Jupiters with small cores (≅ 10 Earth masses), runaway atmospheric escape followed by Roche-lobe overflow may create sub-Jupiter deserts, as observed in both mass and radius distributions of planetary populations. Comparing our results with formation scenarios and observed exoplanets populations, we propose that populations of closely orbiting exoplanets are formed by capturing planets at/inside the inner edges of protoplanetary disks and subsequent evaporation of sub-Jupiters.« less

Development of an In-Situ Decommissioning Sensor Network Test Bed for Structural Condition Monitoring - 12156

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeigler, Kristine E.; Ferguson, Blythe A.

2012-07-01

The Savannah River National Laboratory (SRNL) has established an In Situ Decommissioning (ISD) Sensor Network Test Bed, a unique, small scale, configurable environment, for the assessment of prospective sensors on actual ISD system material, at minimal cost. The Department of Energy (DOE) is presently implementing permanent entombment of contaminated, large nuclear structures via ISD. The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. Validation of ISD system performance models and verification of actual system conditions can be achieved through the development a system of sensors to monitor the materials andmore » condition of the structure. The ISD Sensor Network Test Bed has been designed and deployed to addresses the DOE-Environmental Management Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building at the Savannah River Site. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of groutable thermistors for temperature and moisture monitoring, strain gauges for crack growth monitoring, tilt-meters for settlement monitoring, and a communication system for data collection. Baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment. The Sensor Network Test Bed at SRNL uses COTS sensors on concrete blocks from the outer wall of the P Reactor Building to measure conditions expected to occur in ISD structures. Knowledge and lessons learned gained from installation, testing, and monitoring of the equipment will be applied to sensor installation in a meso-scale test bed at FIU and in future ISD structures. The initial data collected from the sensors installed on the P Reactor Building blocks define the baseline materials condition of the P Reactor ISD external concrete structure. Continued monitoring of the blocks will enable evaluation of the effects of aging on the P Reactor ISD structure. The collected data will support validation of the material degradation model and assessment of the condition of the ISD structure over time. The following are recommendations for continued development of the ISD Sensor Network Test Bed: - Establish a long-term monitoring program using the concrete blocks with existing sensor and/or additional sensors for trending the concrete materials and structural condition; - Continue development of a stand-alone test bed sensor system that is self-powered and provides wireless transmission of data to a user-accessible dashboard; - Develop and implement periodic NDE/DE characterization of the concrete blocks to provide verification and validation for the measurements obtained through the sensor system and concrete degradation model(s). (authors)« less

On the importance of telemetric temperature sensor location during intraperitoneal implantation in rats.

PubMed

Chapon, P A; Bulla, J; Gauthier, A; Moussay, S

2014-04-01

This study aims to assess the thermal homogeneity of the intraperitoneal (IP) cavity and the relevance of using a fixed telemetric temperature sensor at a given location in studying rodents. Ten rats were intraperitoneally implanted with three Jonah® capsules each; after assessing the accuracy and reliability of the sensors. Two capsules were attached, one to the right iliac fossa (RIF) and the other to the left hypochondrium (LH), and another was placed between the intestines but not attached (Free). In the ex vivo condition, the differences between sensors and reference values remained in the range of ±0.1. In the in vivo condition, each sensor enabled the observation of temperature patterns. However, sensor location affected mean and median temperature values while the rats were moving freely. Indeed, temperature data collected in the LH were 0.1 significantly higher than those collected in the RIF and temperature data collected in the LH were 0.11 significantly higher than those collected with the Free capsules. In in vivo conditions, intra-sensor variability of temperature data was not affected by sensor location. Taking into account sensor accuracy, similar intra-sensor variability, and mean differences observed between the three locations, the impact of sensor location within the IP cavity could be considered negligible. In in vivo conditions, temperature differences between locations regularly exceeded ±0.2 and reached up to 2.5. These extreme values could be explained by behavioral factors such as food or water intake. Finally, considering the good thermal homogeneity of the IP cavity and possible adverse consequences of sensor attachment, it seems better to let sensors range free within the cavity.

Health monitoring method for composite materials

DOEpatents

Watkins, Jr., Kenneth S.; Morris, Shelby J [Hampton, VA

2011-04-12

An in-situ method for monitoring the health of a composite component utilizes a condition sensor made of electrically conductive particles dispersed in a polymeric matrix. The sensor is bonded or otherwise formed on the matrix surface of the composite material. Age-related shrinkage of the sensor matrix results in a decrease in the resistivity of the condition sensor. Correlation of measured sensor resistivity with data from aged specimens allows indirect determination of mechanical damage and remaining age of the composite component.

Design of an Intelligent Front-End Signal Conditioning Circuit for IR Sensors

NASA Astrophysics Data System (ADS)

de Arcas, G.; Ruiz, M.; Lopez, J. M.; Gutierrez, R.; Villamayor, V.; Gomez, L.; Montojo, Mª. T.

2008-02-01

This paper presents the design of an intelligent front-end signal conditioning system for IR sensors. The system has been developed as an interface between a PbSe IR sensor matrix and a TMS320C67x digital signal processor. The system architecture ensures its scalability so it can be used for sensors with different matrix sizes. It includes an integrator based signal conditioning circuit, a data acquisition converter block, and a FPGA based advanced control block that permits including high level image preprocessing routines such as faulty pixel detection and sensor calibration in the signal conditioning front-end. During the design phase virtual instrumentation technologies proved to be a very valuable tool for prototyping when choosing the best A/D converter type for the application. Development time was significantly reduced due to the use of this technology.

Source Localization in Wireless Sensor Networks with Randomly Distributed Elements under Multipath Propagation Conditions

DTIC Science & Technology

2009-03-01

IN WIRELESS SENSOR NETWORKS WITH RANDOMLY DISTRIBUTED ELEMENTS UNDER MULTIPATH PROPAGATION CONDITIONS by Georgios Tsivgoulis March 2009...COVERED Engineer’s Thesis 4. TITLE Source Localization in Wireless Sensor Networks with Randomly Distributed Elements under Multipath Propagation...the non-line-of-sight information. 15. NUMBER OF PAGES 111 14. SUBJECT TERMS Wireless Sensor Network , Direction of Arrival, DOA, Random

--No Title--

Science.gov Websites

------ map -----------------------------------------------*/ .mapWrapper { margin:0 auto ; overflow: auto; } .mapWrapper img { float: left; padding-right: 5px; padding-top: 2px; } .mapWrapper ul

[Pollution Characteristics of Surface Runoff of Typical Town in Chongqing City].

PubMed

Wang, Long-tao; Duan, Bing-zheng; Zhao, Jian-wei; Hua, Yu-mei; Zhu, Duan-wei

2015-08-01

Six kinds of impermeable underlying surface, cement tile roof, asbestos roof, cement flat roof, residential concrete pavement, asphalt pavement of restaurants, asphalt pavement of oil depot, and a combined sewer overflow canal in the Jiansheng town of Dadukou district in Chongqing city were chosen as sample plots to study the characteristics of nutritional pollutants and heavy metals in town runoff. The research showed that the average mass concentrations of TSS, COD, TN, TP in road runoff were (1681.2 +/- 677.2), (1154.7 +/- 415.5), (12.07 +/- 2.72), (3.32 +/- 1.15) mgL(-1), respectively. These pollutants were higher than those in roof runoff which were (13.3 +/- 6.5), (100.4 +/- 24.8), (3.58 +/- 0.70), (0.10 +/- 0.02) mg x L(-1), respectively. TDN accounted for 62.60% +/- 34.38% of TN, and TDP accounted for 42.22% +/- 33.94% of TP in the runoff of impermeable underlying surface. Compared with the central urban runoff, town runoff in our study had higher mass concentrations of these pollutants. The mass concentrations of TSS, COD, TDN, TN, TDP and TP in the combined sewer overflow were (281.57 +/- 308.38), (231.21 +/- 42.95), (8.16 +/- 2.78), (10.60 +/- 3.94), (0.38 +/- 0.23) and (1.51 +/- 0.75) mg x L(-1), respectively. The average levels of heavy metals in this kind of runoff did not exceed the class VI level of the surface water environmental quality standard. Most pollutants in the combined sewer overflow had first flush. However, this phenomenon was very rare for TSS. There was a significant positive correlation between TSS and COD, TP in the combined sewer overflow. And this correlation was significant between NH4+ -N and TP, TDP, TN, TDP. However, a negative correlation existed between NO3- -N and all other indicators.

Valley formation by groundwater seepage, pressurized groundwater outbursts and crater-lake overflow in flume experiments with implications for Mars

NASA Astrophysics Data System (ADS)

Marra, Wouter A.; Braat, Lisanne; Baar, Anne W.; Kleinhans, Maarten G.

2014-04-01

Remains of fluvial valleys on Mars reveal the former presence of water on the surface. However, the source of water and the hydrological setting is not always clear, especially in types of valleys that are rare on Earth and where we have limited knowledge of the processes involved. We investigated three hydrological scenarios for valley formation on Mars: hydrostatic groundwater seepage, release of pressurized groundwater and crater-lake overflow. Using physical modeling in laboratory experiments and numerical hydrological modeling we quantitatively studied the morphological development and processes involved in channel formation that result from these different sources of water in unconsolidated sediment. Our results show that valleys emerging from seeping groundwater by headward erosion form relatively slowly as fluvial transport takes place in a channel much smaller than the valley. Pressurized groundwater release forms a characteristic source area at the channel head by fluidization processes. This head consist of a pit in case of superlithostatic pressure and may feature small radial channels and collapse features. Valleys emerging from a crater-lake overflow event develop quickly in a run-away process of rim erosion and discharge increase. The valley head at the crater outflow point has a converging fan shape, and the rapid incision of the rim leaves terraces and collapse features. Morphological elements observed in the experiments can help in identifying the formative processes on Mars, when considerations of experimental scaling and lithological characteristics of the martian surface are taken into account. These morphological features might reveal the associated hydrological settings and formative timescales of a valley. An estimate of formative timescale from sediment transport is best based on the final channel dimensions for groundwater seepage valleys and on the valley dimensions for pressurized groundwater release and crater-lake overflow valleys. Our experiments show that different sources of water form valleys of similar size in quite different timescales.

Natural Risks at the Bottom Side of Ameca River, in the State Limits of Jalisco and Nayarit, Mexico

NASA Astrophysics Data System (ADS)

Pinedo, K. G.; Maciel, R.; Pena, L. E.; García García, E. X.; Ramos Chavez, C.

2016-12-01

At world-wide level, the population centers are exposed to natural risks and more those that are located to borders of the rivers, where hydrometeorological and geologic phenomenon are conjugated, and even increased by the action of the man. From 1911 to 2015, the disasters registered in the world due to flood by river overflowing were 2 701, with 2 545 affected 224 110, of which 60 229 747 lost their homes and 4 449 031 deads, causing therefore an economic loss of approximately $549 052 761 dollars. The case of study is the low part of the Ameca River, the one of the main rivers of the states of Jalisco and Nayarit in the west zone of Mexico. It is interesting, since it have its mouth near the tourist area (with considerable affluence at national level), with infrastructure (airport and bridges) and towns of both referred states; as well because at the pass of the years, this river have had overflows affecting municipalities, bridges and loss of mangrove swamp. In order to determine the feasible impacts to happen with the overflow of the Ameca River, the aerial photographs of area of study and satellite images were analyzed (historical and present), likewise information of the river basin physical environment generated by INEGI with special emphasis in the low part of the river basin and a campaign of work field, to delimit the zones that have shown some affectation. The objective of this investigation is to contribute to the risk analysis of the adjacent localities to the river, with the purpose of diminishing the impact in the population. As preliminary results appear maps with boundaries of paleo-channels, which mark the zone of influence during overflows of the Ameca River, the towns which can be affected and the population exposed.

Analysis of random drop for gateway congestion control. M.S. Thesis

NASA Technical Reports Server (NTRS)

Hashem, Emam Salaheddin

1989-01-01

Lately, the growing demand on the Internet has prompted the need for more effective congestion control policies. Currently No Gateway Policy is used to relieve and signal congestion, which leads to unfair service to the individual users and a degradation of overall network performance. Network simulation was used to illustrate the character of Internet congestion and its causes. A newly proposed gateway congestion control policy, called Random Drop, was considered as a promising solution to the pressing problem. Random Drop relieves resource congestion upon buffer overflow by choosing a random packet from the service queue to be dropped. The random choice should result in a drop distribution proportional to the bandwidth distribution among all contending TCP connections, thus applying the necessary fairness. Nonetheless, the simulation experiments demonstrate several shortcomings with this policy. Because Random Drop is a congestion control policy, which is not applied until congestion has already occurred, it usually results in a high drop rate that hurts too many connections including well-behaved ones. Even though the number of packets dropped is different from one connection to another depending on the buffer utilization upon overflow, the TCP recovery overhead is high enough to neutralize these differences, causing unfair congestion penalties. Besides, the drop distribution itself is an inaccurate representation of the average bandwidth distribution, missing much important information about the bandwidth utilization between buffer overflow events. A modification of Random Drop to do congestion avoidance by applying the policy early was also proposed. Early Random Drop has the advantage of avoiding the high drop rate of buffer overflow. The early application of the policy removes the pressure of congestion relief and allows more accurate signaling of congestion. To be used effectively, algorithms for the dynamic adjustment of the parameters of Early Random Drop to suite the current network load must still be developed.

Neurochemical and behavioural interactions between ibogaine and nicotine in the rat.

PubMed Central

Benwell, M. E.; Holtom, P. E.; Moran, R. J.; Balfour, D. J.

1996-01-01

1. In vivo brain microdialysis has been employed to investigate the effects of ibogaine on nicotine-induced changes in dopamine overflow in the nucleus accumbens (NAc) of freely moving rats. The effects of the compound on locomotor responses to nicotine and behaviour in the elevated plus-maze were also examined. 2. No changes were observed in the dopamine overflow or the locomotor activity of the animals following the administration of ibogaine (40 mg kg-1, i.p.). However, ibogaine, administered 22 h earlier, significantly (P < 0.01) attenuated the increase in dopamine overflow but not the hyperlocomotion, evoked by nicotine. 3. In the elevated plus-maze test, significant reductions in the open:total runway entries in both saline-treated controls (P < 0.05) and nicotine-treated (P < 0.01) rats were obtained when the animals were tested 22 h after pretreatment with ibogaine (40 mg kg-1, i.p.). The total activity was significantly (P < 0.01) greater in the nicotine-treated rats but this response was not affected by ibogaine pretreatment. 4. Administration of ibogaine was associated with reductions in the tissue levels of 5-hydroxyindoleacetic acid (5-HIAA) in the NAc (P < 0.01) and striatum (P < 0.05) and an increase in the level of this metabolite in the medial prefrontal cortex (mPFC) (P < 0.01) while the levels of dopamine and 5-hydroxytryptamine (5-HT) in the mPFC were reduced (P < 0.05). The DOPAC/dopamine (P < 0.05) and 5-HIAA/5-HT (P < 0.01) ratios were significantly increased in the mPFC for at least 7 days after a single treatment with ibogaine. 5. Ibogaine attenuates the nicotine-induced increases in dopamine overflow in the NAc and may, therefore, inhibit the rewarding effects of this drug. However, the long lasting anxiogenesis induced by ibogaine warrant further investigation before its use could be recommended for smokers. PMID:8646423

PEDOT:PSS/QCM-based multimodal humidity and pressure sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muckley, Eric S.; Lynch, James; Kumar, Rajeev

A room-temperature multimodal sensor composed of PEDOT:PSS deposited on an AT-cut quartz crystalmicrobalance (QCM) crystal has been fabricated. The nonlinear resistive and frequency sensor responses aredeconvolved using an articial neural network (ANN), which allows the single sensor to function simultane-ously as a relative humidity (RH) sensor and a pressure sensor using only two electrodes. We demonstratethat the predictive ability of the sensor is highly inuenced by the data used to train the ANN. When trainingsets are tailored to resemble the operating conditions of the sensor, the sensor achieves an average resolutionof < 3% RH from 0-100% RH, even after Hmore » 2O saturation occurs on the surface. Our results indicate thatANNs show strong promise for improving the resolution of low cost gas sensors and for expanding the rangeof environmental conditions in which a given sensor can operate.« less

PEDOT:PSS/QCM-based multimodal humidity and pressure sensor

DOE PAGES

Muckley, Eric S.; Lynch, James; Kumar, Rajeev; ...

2016-05-11

A room-temperature multimodal sensor composed of PEDOT:PSS deposited on an AT-cut quartz crystalmicrobalance (QCM) crystal has been fabricated. The nonlinear resistive and frequency sensor responses aredeconvolved using an articial neural network (ANN), which allows the single sensor to function simultane-ously as a relative humidity (RH) sensor and a pressure sensor using only two electrodes. We demonstratethat the predictive ability of the sensor is highly inuenced by the data used to train the ANN. When trainingsets are tailored to resemble the operating conditions of the sensor, the sensor achieves an average resolutionof < 3% RH from 0-100% RH, even after Hmore » 2O saturation occurs on the surface. Our results indicate thatANNs show strong promise for improving the resolution of low cost gas sensors and for expanding the rangeof environmental conditions in which a given sensor can operate.« less

Comparison of the plenoptic sensor and the Shack-Hartmann sensor.

PubMed

Ko, Jonathan; Davis, Christopher C

2017-05-01

Adaptive optics has been successfully used for decades in the field of astronomy to correct for atmospheric turbulence. A well-developed example involves sensing the slightly distorted wavefronts with a Shack-Hartmann sensor and then correcting them with a phase conjugate device. While the Shack-Hartmann sensor has proven effective for astronomical purposes, it has been less successful for use in deep turbulence conditions often found in ground-to-ground-based optical systems. We have studied an alternative way to sense and correct distorted wavefronts using a plenoptic sensor. We review the design of the plenoptic sensor and directly compare it with the well-known Shack-Hartmann sensor. An experimental comparison of the plenoptic sensor and the Shack-Hartmann sensor is performed to highlight their differences in real-world atmospheric turbulence conditions.

A High-Temperature Piezoresistive Pressure Sensor with an Integrated Signal-Conditioning Circuit.

PubMed

Yao, Zong; Liang, Ting; Jia, Pinggang; Hong, Yingping; Qi, Lei; Lei, Cheng; Zhang, Bin; Xiong, Jijun

2016-06-18

This paper focuses on the design and fabrication of a high-temperature piezoresistive pressure sensor with an integrated signal-conditioning circuit, which consists of an encapsulated pressure-sensitive chip, a temperature compensation circuit and a signal-conditioning circuit. A silicon on insulation (SOI) material and a standard MEMS process are used in the pressure-sensitive chip fabrication, and high-temperature electronic components are adopted in the temperature-compensation and signal-conditioning circuits. The entire pressure sensor achieves a hermetic seal and can be operated long-term in the range of -50 °C to 220 °C. Unlike traditional pressure sensor output voltage ranges (in the dozens to hundreds of millivolts), the output voltage of this sensor is from 0 V to 5 V, which can significantly improve the signal-to-noise ratio and measurement accuracy in practical applications of long-term transmission based on experimental verification. Furthermore, because this flexible sensor's output voltage is adjustable, general follow-up pressure transmitter devices for voltage converters need not be used, which greatly reduces the cost of the test system. Thus, the proposed high-temperature piezoresistive pressure sensor with an integrated signal-conditioning circuit is expected to be highly applicable to pressure measurements in harsh environments.

TMI-2 - A Case Study for PWR Instrumentation Performance during a Severe Accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joy L. Rempe; Darrell L. Knudson

2013-03-01

The accident at the Three Mile Island Unit 2 (TMI-2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated in 2012 by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focussed upon a set of sensorsmore » that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this report. For each sensor, a description is provided with the measured data and conclusions related to the sensor’s survivability, and the basis for conclusions about its survivability. As noted within this document, several techniques were invoked in the TMI-2 post-accident evaluation program to assess sensor status, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this document provides recommendations related to the sensor survivability and data evaluation process that could be implemented in upcoming Fukushima Daiichi recovery efforts.« less

TMI-2 - A Case Study for PWR Instrumentation Performance during a Severe Accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joy L. Rempe; Darrell L. Knudson

2014-05-01

The accident at the Three Mile Island Unit 2 (TMI-2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated in 2012 by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focussed upon a set of sensorsmore » that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this report. For each sensor, a description is provided with the measured data and conclusions related to the sensor’s survivability, and the basis for conclusions about its survivability. As noted within this document, several techniques were invoked in the TMI-2 post-accident evaluation program to assess sensor status, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this document provides recommendations related to the sensor survivability and data evaluation process that could be implemented in upcoming Fukushima Daiichi recovery efforts.« less

High-frequency monitoring of water fluxes and nutrient loads to assess the effects of controlled drainage on water storage and nutrient transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rozemeijer, J. C.; Visser, A.; Borren, W.

High nitrogen (N) and phosphorus (P) fluxes from upstream agriculture threaten aquatic ecosystems in surface waters and estuaries, especially in areas characterized by high agricultural N and P inputs and densely drained catchments like the Netherlands. Controlled drainage has been recognized as an effective option to optimize soil moisture conditions for agriculture and to reduce unnecessary losses of fresh water and nutrients. This is achieved by introducing control structures with adjustable overflow levels into subsurface tube drain systems. A small-scale (1 ha) field experiment was designed to investigate the hydrological and chemical changes after introducing controlled drainage. Precipitation rates andmore » the response of water tables and drain fluxes were measured in the periods before the introduction of controlled drainage (2007–2008) and after (2009–2011). For the N and P concentration measurements, auto-analyzers for continuous records were combined with passive samplers for time-averaged concentrations at individual drain outlets. The experimental setup enabled the quantification of changes in the water and solute balance after introducing controlled drainage. The results showed that introducing controlled drainage reduced the drain discharge and increased the groundwater storage in the field. To achieve this, the overflow levels have to be elevated in early spring, before the drain discharge stops due to dryer conditions and falling groundwater levels. The groundwater storage in the field would have been larger if the water levels in the adjacent ditch were controlled as well by an adjustable weir. The N concentrations and loads increased, which was largely related to elevated concentrations in one of the three monitored tube drains. The P loads via the tube drains reduced due to the reduction in discharge after introducing controlled drainage. Furthermore, this may be counteracted by the higher groundwater levels and the larger contribution of N- and P-rich shallow groundwater and overland flow to the surface water.« less

High-frequency monitoring of water fluxes and nutrient loads to assess the effects of controlled drainage on water storage and nutrient transport

DOE PAGES

Rozemeijer, J. C.; Visser, A.; Borren, W.; ...

2016-01-19

High nitrogen (N) and phosphorus (P) fluxes from upstream agriculture threaten aquatic ecosystems in surface waters and estuaries, especially in areas characterized by high agricultural N and P inputs and densely drained catchments like the Netherlands. Controlled drainage has been recognized as an effective option to optimize soil moisture conditions for agriculture and to reduce unnecessary losses of fresh water and nutrients. This is achieved by introducing control structures with adjustable overflow levels into subsurface tube drain systems. A small-scale (1 ha) field experiment was designed to investigate the hydrological and chemical changes after introducing controlled drainage. Precipitation rates andmore » the response of water tables and drain fluxes were measured in the periods before the introduction of controlled drainage (2007–2008) and after (2009–2011). For the N and P concentration measurements, auto-analyzers for continuous records were combined with passive samplers for time-averaged concentrations at individual drain outlets. The experimental setup enabled the quantification of changes in the water and solute balance after introducing controlled drainage. The results showed that introducing controlled drainage reduced the drain discharge and increased the groundwater storage in the field. To achieve this, the overflow levels have to be elevated in early spring, before the drain discharge stops due to dryer conditions and falling groundwater levels. The groundwater storage in the field would have been larger if the water levels in the adjacent ditch were controlled as well by an adjustable weir. The N concentrations and loads increased, which was largely related to elevated concentrations in one of the three monitored tube drains. The P loads via the tube drains reduced due to the reduction in discharge after introducing controlled drainage. Furthermore, this may be counteracted by the higher groundwater levels and the larger contribution of N- and P-rich shallow groundwater and overland flow to the surface water.« less

Determining the spill flow discharge of combined sewer overflows using rating curves based on computational fluid dynamics instead of the standard weir equation.

PubMed

Fach, S; Sitzenfrei, R; Rauch, W

2009-01-01

It is state of the art to evaluate and optimise sewer systems with urban drainage models. Since spill flow data is essential in the calibration process of conceptual models it is important to enhance the quality of such data. A wide spread approach is to calculate the spill flow volume by using standard weir equations together with measured water levels. However, these equations are only applicable to combined sewer overflow (CSO) structures, whose weir constructions correspond with the standard weir layout. The objective of this work is to outline an alternative approach to obtain spill flow discharge data based on measurements with a sonic depth finder. The idea is to determine the relation between water level and rate of spill flow by running a detailed 3D computational fluid dynamics (CFD) model. Two real world CSO structures have been chosen due to their complex structure, especially with respect to the weir construction. In a first step the simulation results were analysed to identify flow conditions for discrete steady states. It will be shown that the flow conditions in the CSO structure change after the spill flow pipe acts as a controlled outflow and therefore the spill flow discharge cannot be described with a standard weir equation. In a second step the CFD results will be used to derive rating curves which can be easily applied in everyday practice. Therefore the rating curves are developed on basis of the standard weir equation and the equation for orifice-type outlets. Because the intersection of both equations is not known, the coefficients of discharge are regressed from CFD simulation results. Furthermore, the regression of the CFD simulation results are compared with the one of the standard weir equation by using historic water levels and hydrographs generated with a hydrodynamic model. The uncertainties resulting of the wide spread use of the standard weir equation are demonstrated.

High-frequency monitoring of water fluxes and nutrient loads to assess the effects of controlled drainage on water storage and nutrient transport

NASA Astrophysics Data System (ADS)

Rozemeijer, J. C.; Visser, A.; Borren, W.; Winegram, M.; van der Velde, Y.; Klein, J.; Broers, H. P.

2016-01-01

High nitrogen (N) and phosphorus (P) fluxes from upstream agriculture threaten aquatic ecosystems in surface waters and estuaries, especially in areas characterized by high agricultural N and P inputs and densely drained catchments like the Netherlands. Controlled drainage has been recognized as an effective option to optimize soil moisture conditions for agriculture and to reduce unnecessary losses of fresh water and nutrients. This is achieved by introducing control structures with adjustable overflow levels into subsurface tube drain systems. A small-scale (1 ha) field experiment was designed to investigate the hydrological and chemical changes after introducing controlled drainage. Precipitation rates and the response of water tables and drain fluxes were measured in the periods before the introduction of controlled drainage (2007-2008) and after (2009-2011). For the N and P concentration measurements, auto-analyzers for continuous records were combined with passive samplers for time-averaged concentrations at individual drain outlets. The experimental setup enabled the quantification of changes in the water and solute balance after introducing controlled drainage. The results showed that introducing controlled drainage reduced the drain discharge and increased the groundwater storage in the field. To achieve this, the overflow levels have to be elevated in early spring, before the drain discharge stops due to dryer conditions and falling groundwater levels. The groundwater storage in the field would have been larger if the water levels in the adjacent ditch were controlled as well by an adjustable weir. The N concentrations and loads increased, which was largely related to elevated concentrations in one of the three monitored tube drains. The P loads via the tube drains reduced due to the reduction in discharge after introducing controlled drainage. However, this may be counteracted by the higher groundwater levels and the larger contribution of N- and P-rich shallow groundwater and overland flow to the surface water.

Impact Analysis of Temperature and Humidity Conditions on Electrochemical Sensor Response in Ambient Air Quality Monitoring

PubMed Central

Ning, Zhi; Ye, Sheng; Sun, Li; Yang, Fenhuan; Wong, Ka Chun; Westerdahl, Dane; Louie, Peter K. K.

2018-01-01

The increasing applications of low-cost air sensors promises more convenient and cost-effective systems for air monitoring in many places and under many conditions. However, the data quality from such systems has not been fully characterized and may not meet user expectations in research and regulatory uses, or for use in citizen science. In our study, electrochemical sensors (Alphasense B4 series) for carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and oxidants (Ox) were evaluated under controlled laboratory conditions to identify the influencing factors and quantify their relation with sensor outputs. Based on the laboratory tests, we developed different correction methods to compensate for the impact of ambient conditions. Further, the sensors were assembled into a monitoring system and tested in ambient conditions in Hong Kong side-by-side with regulatory reference monitors, and data from these tests were used to evaluate the performance of the models, to refine them, and validate their applicability in variable ambient conditions in the field. The more comprehensive correction models demonstrated enhanced performance when compared with uncorrected data. One over-arching observation of this study is that the low-cost sensors may promise excellent sensitivity and performance, but it is essential for users to understand and account for several key factors that may strongly affect the nature of sensor data. In this paper, we also evaluated factors of multi-month stability, temperature, and humidity, and considered the interaction of oxidant gases NO2 and ozone on a newly introduced oxidant sensor. PMID:29360749

Impact Analysis of Temperature and Humidity Conditions on Electrochemical Sensor Response in Ambient Air Quality Monitoring.

PubMed

Wei, Peng; Ning, Zhi; Ye, Sheng; Sun, Li; Yang, Fenhuan; Wong, Ka Chun; Westerdahl, Dane; Louie, Peter K K

2018-01-23

The increasing applications of low-cost air sensors promises more convenient and cost-effective systems for air monitoring in many places and under many conditions. However, the data quality from such systems has not been fully characterized and may not meet user expectations in research and regulatory uses, or for use in citizen science. In our study, electrochemical sensors (Alphasense B4 series) for carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO₂), and oxidants (O x ) were evaluated under controlled laboratory conditions to identify the influencing factors and quantify their relation with sensor outputs. Based on the laboratory tests, we developed different correction methods to compensate for the impact of ambient conditions. Further, the sensors were assembled into a monitoring system and tested in ambient conditions in Hong Kong side-by-side with regulatory reference monitors, and data from these tests were used to evaluate the performance of the models, to refine them, and validate their applicability in variable ambient conditions in the field. The more comprehensive correction models demonstrated enhanced performance when compared with uncorrected data. One over-arching observation of this study is that the low-cost sensors may promise excellent sensitivity and performance, but it is essential for users to understand and account for several key factors that may strongly affect the nature of sensor data. In this paper, we also evaluated factors of multi-month stability, temperature, and humidity, and considered the interaction of oxidant gases NO₂ and ozone on a newly introduced oxidant sensor.

Milwaukee Estuary AOC

EPA Pesticide Factsheets

The rivers in the Milwaukee estuary in Wisconsin drain into Lake Michigan. Wastewater treatment plants and combined sewer overflows contribute pollution which affects fish and wildlife and recreation.

Selected Micropollutants as Indicators in a Karst Catchment

NASA Astrophysics Data System (ADS)

Zirlewagen, Johannes; Schiperski, Ferry; Hillebrand, Olav; Nödler, Karsten; Licha, Tobias; Scheytt, Traugott

2015-04-01

High flow dynamics and variations in water quality are typical for karst springs and reflect the complex interaction of different flow and storage components within a karst system. Event-based monitoring of mobile micropollutants in spring water combined with information on their input is used (1) to quantify the impact of certain contamination scenarios on spring water quality and (2) to gain additional information on the intrinsic characteristics of a karst system. We employ the artificial sweeteners acesulfame and cyclamate as source specific indicators for sewage along with the herbicides atrazine and isoproturon for agriculture. The study site is the 45 km² rural catchment of the perennial karst spring Gallusquelle in SW-Germany (mean discharge: 0.5 m³/s). Overflow events of a stormwater detention basin (SDB, combined sewer system) are known to impact water quality. Most of the sewer system is situated in the SW of the catchment. Most agricultural land is found in the NE. Neither atrazine nor significant amounts of isoproturon were detected in wastewater. Concentrations and mass fluxes of acesulfame and cyclamate in wastewater were determined. The combined evaluation of the persistent compound acesulfame with the rather degradable cyclamate allows for the distinction of long and short transit times and thus slow and fast flow components. The same applies for atrazine (persistent) and isoproturon (degradable). In Germany, acesulfame was licensed in 1990, atrazine was banned shortly after, in 1991. During low flow conditions only atrazine (max. 4 ng/L) and acesulfame (max. 20 ng/L) were detected in spring water. After a recharge event without SDB overflow concentrations as well as mass fluxes of both compounds decreased, reflecting an increasing portion of event water in spring discharge. A breakthrough of isoproturon (max. 9 ng/L) indicated the arrival of water from croplands. After a recharge event accompanied by a SDB overflow cyclamate was detected at max. 28 ng/L. Simultaneously, acesulfame concentrations show superposition of background dilution (old component) and a breakthrough (fresh component, max. 22 ng/L). 1-D-transport-modelling of the cyclamate breakthrough revealed results that are in good agreement with the results of other studies. Analyses of micropollutants might become very sensitive tools in karst hydrogeology where natural background concentrations and signal dampening are limiting factors for conventional investigation methods.

Description and testing of three moisture sensors for measuring surface wetness on carbonate building stones

USGS Publications Warehouse

See, R.B.; Reddy, M.M.; Martin, R.G.

1987-01-01

Three sensors were tested on building stones exposed to conditions that produce deposition of moisture. A relative humidity probe, a gypsum collected circuit grid, and a limestone block resistor were tested as sensors for determining surface wetness. Sensors were tested under laboratory conditions of constant relative humidity and temperature and also under on-site conditions of variable relative humidity and temperature for 8 weeks at Newcomb, New York. Laboratory tests indicated that relative humidity alone did not cause sensors to become saturated. However, relative humidity did control the rate at which sensors dried after being saturated with distilled water. On-site testing of the relative humidity probe and the gypsum coated circuit grid indicated that they respond to a diurnal wetting and drying cycle; the limestone block resistor only responded to rainfall. (Author 's abstract)

Coastal flooding events on the French coast of the eastern English Channel: the result of a combination of meteorological, marine, and morphological factors

NASA Astrophysics Data System (ADS)

Letortu, P.; Costa, S.; Cantat, O.; Levoy, F.; Dauvin, J. C.; De Saint-Léger, E.

2012-04-01

On account of increasing inhabitation and development of coastal areas, the economical stakes are high for forecasting and prevention of coastal flooding risk. Because of its exposure to prevailing Westerlies, morphological, and topographic features, low coastal areas on the French coast of the eastern English Channel are particularly sensitive to this natural risk. This sensitivity, that has always characterized this study area, is becoming worrying to politicians and inhabitants. The study aim is to identify, from 1949 to 2010, the possible increase of frequency and intensity of these meteorological and marine events, and their characteristics for forecasting objectives. The chosen approach is made up of three elements: 1) An analysis of strong west wind over the last decades has been implemented from Meteo-France data of Dieppe, reliable regional meteorological station. Beyond multi-annual random fluctuations, we have noticed a decrease in frequency and intensity of strong winds traditionally involved in flooding events. 2) An analysis of past events has been carried out from many information sources to warrant the accuracy of statements and their exhaustiveness. Thanks to this database, the main results are: i) the absence of increasing trend about frequency and intensity of coastal flooding events; ii) the cartography of coastal flooding risk for each urbanized area; iii) the definition of wind and tide level thresholds (7 m/s and 8.49 m at Dieppe) above which there is flooding. 3) A characterization, on the synoptic scale, of meteorological conditions ending in flooding has been performed. In matching this piece of information with the past events inventory, we have identified: firstly the two major types of low pressure trajectories that generated overflowing, so the two main atmospheric circulations prone to flooding, and secondly the fundamental meteorological aspect of the high north-west pressure gradient (≥ 20 hPa from "Pointe du Raz" (France) to Cromer city (U.K.)) of these flooding events. Frequency of this particular pressure configuration in the English Channel does not highlight any significant trend during the last century. Beyond tide level and wind (speed, direction) thresholds, another factor explains coastal flooding events. This is the matter of atmospheric cold front during high tide, observable in 70 % of coastal flooding events in the eastern English Channel. Analysis of these coastal flooding events cannot be restricted to simple meteorological and marine conditions during overflowing by the sea. This work emphasizes the need for longer analysis period. It is important to encompass the possible beach "preparation time" (lowering of the beach profile) by meteorological and marine conditions for a few days or weeks before flooding event. This "preparation time" may be short: 48 hours of strong winds (> 8 m/s) may be sufficient to shape a beach profile prone to overflowing. Coastal flooding is the result of a combination of factors from various time and space scales, which goes over the simple combination of extreme sea-level and strong wind perpendicular to coast.

Minimized Bolus-Type Wireless Sensor Node with a Built-In Three-Axis Acceleration Meter for Monitoring a Cow’s Rumen Conditions

PubMed Central

Nogami, Hirofumi; Arai, Shozo; Okada, Hironao; Zhan, Lan; Itoh, Toshihiro

2017-01-01

Monitoring rumen conditions in cows is important because a dysfunctional rumen system may cause death. Sub-acute ruminal acidosis (SARA) is a typical disease in cows, and is characterized by repeated periods of low ruminal pH. SARA is regarded as a trigger for rumen atony, rumenitis, and abomasal displacement, which may cause death. In previous studies, rumen conditions were evaluated by wireless sensor nodes with pH measurement capability. The primary advantage of the pH sensor is its ability to continuously measure ruminal pH. However, these sensor nodes have short lifetimes since they are limited by the finite volume of the internal liquid of the reference electrode. Mimicking rumen atony, we attempt to evaluate the rumen condition using wireless sensor nodes with three-axis accelerometers. The theoretical life span of such sensor nodes depends mainly on the transmission frequency of acceleration data and the size of the battery, and the proposed sensor nodes are 30.0 mm in diameter and 70.0 mm in length and have a life span of over 600 days. Using the sensor nodes, we compare the rumen motility of the force transducer measurement with the three-axis accelerometer data. As a result, we can detect discriminative movement of rumen atony. PMID:28346374

Minimized Bolus-Type Wireless Sensor Node with a Built-In Three-Axis Acceleration Meter for Monitoring a Cow's Rumen Conditions.

PubMed

Nogami, Hirofumi; Arai, Shozo; Okada, Hironao; Zhan, Lan; Itoh, Toshihiro

2017-03-27

Monitoring rumen conditions in cows is important because a dysfunctional rumen system may cause death. Sub-acute ruminal acidosis (SARA) is a typical disease in cows, and is characterized by repeated periods of low ruminal pH. SARA is regarded as a trigger for rumen atony, rumenitis, and abomasal displacement, which may cause death. In previous studies, rumen conditions were evaluated by wireless sensor nodes with pH measurement capability. The primary advantage of the pH sensor is its ability to continuously measure ruminal pH. However, these sensor nodes have short lifetimes since they are limited by the finite volume of the internal liquid of the reference electrode. Mimicking rumen atony, we attempt to evaluate the rumen condition using wireless sensor nodes with three-axis accelerometers. The theoretical life span of such sensor nodes depends mainly on the transmission frequency of acceleration data and the size of the battery, and the proposed sensor nodes are 30.0 mm in diameter and 70.0 mm in length and have a life span of over 600 days. Using the sensor nodes, we compare the rumen motility of the force transducer measurement with the three-axis accelerometer data. As a result, we can detect discriminative movement of rumen atony.

Instrumentation Performance During the TMI-2 Accident

NASA Astrophysics Data System (ADS)

Rempe, Joy L.; Knudson, Darrell L.

2014-08-01

The accident at the Three Mile Island Unit 2 (TMI-2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. The loss of coolant and the hydrogen combustion that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focused upon a set of sensors that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this paper. As noted within this paper, several techniques were invoked in the TMI-2 post-accident program to evaluate sensor survivability status and data qualification, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this paper provides recommendations related to sensor survivability and the data evaluation process that could be implemented in upcoming Fukushima Daiichi recovery efforts.

40 CFR 1065.215 - Pressure transducers, temperature sensors, and dewpoint sensors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... sensors, and dewpoint sensors. 1065.215 Section 1065.215 Protection of Environment ENVIRONMENTAL... Measurement of Engine Parameters and Ambient Conditions § 1065.215 Pressure transducers, temperature sensors, and dewpoint sensors. (a) Application. Use instruments as specified in this section to measure...

A Tailored Ontology Supporting Sensor Implementation for the Maintenance of Industrial Machines.

PubMed

Maleki, Elaheh; Belkadi, Farouk; Ritou, Mathieu; Bernard, Alain

2017-09-08

The longtime productivity of an industrial machine is improved by condition-based maintenance strategies. To do this, the integration of sensors and other cyber-physical devices is necessary in order to capture and analyze a machine's condition through its lifespan. Thus, choosing the best sensor is a critical step to ensure the efficiency of the maintenance process. Indeed, considering the variety of sensors, and their features and performance, a formal classification of a sensor's domain knowledge is crucial. This classification facilitates the search for and reuse of solutions during the design of a new maintenance service. Following a Knowledge Management methodology, the paper proposes and develops a new sensor ontology that structures the domain knowledge, covering both theoretical and experimental sensor attributes. An industrial case study is conducted to validate the proposed ontology and to demonstrate its utility as a guideline to ease the search of suitable sensors. Based on the ontology, the final solution will be implemented in a shared repository connected to legacy CAD (computer-aided design) systems. The selection of the best sensor is, firstly, obtained by the matching of application requirements and sensor specifications (that are proposed by this sensor repository). Then, it is refined from the experimentation results. The achieved solution is recorded in the sensor repository for future reuse. As a result, the time and cost of the design process of new condition-based maintenance services is reduced.

Application of a High-Fidelity Icing Analysis Method to a Model-Scale Rotor in Forward Flight

NASA Technical Reports Server (NTRS)

Narducci, Robert; Orr, Stanley; Kreeger, Richard E.

2012-01-01

An icing analysis process involving the loose coupling of OVERFLOW-RCAS for rotor performance prediction and with LEWICE3D for thermal analysis and ice accretion is applied to a model-scale rotor for validation. The process offers high-fidelity rotor analysis for the noniced and iced rotor performance evaluation that accounts for the interaction of nonlinear aerodynamics with blade elastic deformations. Ice accumulation prediction also involves loosely coupled data exchanges between OVERFLOW and LEWICE3D to produce accurate ice shapes. Validation of the process uses data collected in the 1993 icing test involving Sikorsky's Powered Force Model. Non-iced and iced rotor performance predictions are compared to experimental measurements as are predicted ice shapes.

Hole injection and electron overflow improvement in InGaN/GaN light-emitting diodes by a tapered AlGaN electron blocking layer.

PubMed

Lin, Bing-Chen; Chen, Kuo-Ju; Wang, Chao-Hsun; Chiu, Ching-Hsueh; Lan, Yu-Pin; Lin, Chien-Chung; Lee, Po-Tsung; Shih, Min-Hsiung; Kuo, Yen-Kuang; Kuo, Hao-Chung

2014-01-13

A tapered AlGaN electron blocking layer with step-graded aluminum composition is analyzed in nitride-based blue light-emitting diode (LED) numerically and experimentally. The energy band diagrams, electrostatic fields, carrier concentration, electron current density profiles, and hole transmitting probability are investigated. The simulation results demonstrated that such tapered structure can effectively enhance the hole injection efficiency as well as the electron confinement. Consequently, the LED with a tapered EBL grown by metal-organic chemical vapor deposition exhibits reduced efficiency droop behavior of 29% as compared with 44% for original LED, which reflects the improvement in hole injection and electron overflow in our design.

Validation of High-Speed Turbulent Boundary Layer and Shock-Boundary Layer Interaction Computations with the OVERFLOW Code

NASA Technical Reports Server (NTRS)

Oliver, A. B.; Lillard, R. P.; Blaisdell, G. A.; Lyrintizis, A. S.

2006-01-01

The capability of the OVERFLOW code to accurately compute high-speed turbulent boundary layers and turbulent shock-boundary layer interactions is being evaluated. Configurations being investigated include a Mach 2.87 flat plate to compare experimental velocity profiles and boundary layer growth, a Mach 6 flat plate to compare experimental surface heat transfer,a direct numerical simulation (DNS) at Mach 2.25 for turbulent quantities, and several Mach 3 compression ramps to compare computations of shock-boundary layer interactions to experimental laser doppler velocimetry (LDV) data and hot-wire data. The present paper describes outlines the study and presents preliminary results for two of the flat plate cases and two small-angle compression corner test cases.

Overflow of a dipolar exciton trap at high magnetic fields

NASA Astrophysics Data System (ADS)

Dietl, Sebastian; Kowalik-Seidl, Katarzyna; Hammer, Lukas; Schuh, Dieter; Wegscheider, Werner; Holleitner, Alexander; Wurstbauer, Ursula

We study the photoluminescence of trapped dipolar excitons (IX) in coupled double GaAs quantum wells at low temperatures and high magnetic fields. A voltage-tunable electrode geometry controls the strength of the quantum confined Stark effect and defines the lateral trapping potential. Furthermore, it enhances the IX lifetime, enabling them to cool down to lattice temperature. We show that a magnetic field in Faraday configuration effectively prevents the escape of unbound photogenerated charge carriers from the trap area, thus increasing the density of dipolar excitons. For large magnetic fields, we observe an overflow of the IX trap and an effectively suppressed quantum confined Stark effect. We acknowledge financial support by the German Excellence Initiative via the Nanosystems Initiative Munich (NIM).

Device and method for automated separation of a sample of whole blood into aliquots

DOEpatents

Burtis, Carl A.; Johnson, Wayne F.

1989-01-01

A device and a method for automated processing and separation of an unmeasured sample of whole blood into multiple aliquots of plasma. Capillaries are radially oriented on a rotor, with the rotor defining a sample chamber, transfer channels, overflow chamber, overflow channel, vent channel, cell chambers, and processing chambers. A sample of whole blood is placed in the sample chamber, and when the rotor is rotated, the blood moves outward through the transfer channels to the processing chambers where the blood is centrifugally separated into a solid cellular component and a liquid plasma component. When the rotor speed is decreased, the plasma component backfills the capillaries resulting in uniform aliquots of plasma which may be used for subsequent analytical procedures.

Improving sediment transport measurements in the Erlenbach stream using a moving basket system

NASA Astrophysics Data System (ADS)

Rickenmann, Dieter; Turowski, Jens; Hegglin, Ramon; Fritschi, Bruno

2010-05-01

In the Erlenbach stream, a prealpine torrent in Switzerland, sediment transport has been monitored for more than 25 years. Sediment transporting flood events in the Erlenbach are typically of short duration with a rapid rise of discharge during summer thunderstorms, thus hampering on-site measurements. On average there are more than 20 bedload transport events per year. Near the confluence with the main valley river, there is a stream gauging station and a sediment retention basin with a capacity of about 2,000 m3. The basin is surveyed at regular intervals and after large flood events. In addition, sediment transport has been continuously monitored with a piezoelectric bedload impact sensor (PBIS) array since 1986. The sensor array is mounted flush with the surface of a check dam immediately upstream of the retention basin. The PBIS system was developed to continuously measure the intensity of bedload transport and its relation to stream discharge. To standardize the sensors, the piezoelectric crystals were replaced by geophones in 2000. The geophone measuring system has also been employed at a number of other streams. In 2008, the measuring system in the Erlenbach stream has been enhanced with an automatic system to obtain bedload samples. Movable, slot-type cubic metal baskets are mounted on a rail at the downstream wall of the large check dam above the retention basin. The metal baskets can be moved automatically and individually into the flow according to flow and bedload transport conditions (i.e. geophone recordings). The basket is stopped at the centerline of the approach flow channel of the overflow section to obtain a sediment sample during a limited time interval. The wire mesh of the basket has a spacing of 10 mm to sample all sediment particles coarser than this size (which is about the limiting grain size detected by the geophones). The weight increase due to the collected sediment is measured by weighing cells located in the basket supporting structure, and this information is used in combination with the geophone recordings to determine when to move a basket laterally away from the flow. The upgraded measuring system allows: (i) to obtain bedload samples over short sampling periods; (ii) to measure the grain size distribution of the transported material and its variation over time and with discharge; (iii) to obtain direct bedload measurements that can be used to improve the understanding of the geophone signal; and (iv) to improve the geophone calibration for the Erlenbach stream. We introduce the new measuring installations, discuss our experience from the first successful automatic sampling operations in summer 2009, and we present first results.

Deployment System and Method for Subsurface Launched Unmanned Aerial Vehicle

DTIC Science & Technology

2006-11-15

conditions exterior to the capsule are satisfactory for deployment. For example, weather gauges, accelerometers, tiltmeters and/or other sensors 30 can...the surface. [0009) Upon surfacing, or after a predetermined delay, and preferably at a time when sensors on and/or within the tube determine that... sensors for obtaining measurements of ambient conditions at least one of within and exterior to the capsule. The sensors can measure a depth of the

Description and testing of three moisture sensors for measuring surface wetness on carbonate building stones

USGS Publications Warehouse

See, R.B.; Reddy, M.M.; Martin, R.G.

1988-01-01

Three moisture sensors were tested as a means for determining the surface wetness on carbonate building stones exposed to conditions that produce deposition of moisture. A relative-humidity probe, a gypsum-coated circuit grid, and a limestone-block resistor were tested as sensors for determining surface wetness. Sensors were tested under laboratory conditions of constant relative humidity and temperature and also under on-site conditions of variable relative humidity and temperature for eight weeks at Newcomb, NY. Laboratory tests indicated that relative humidity alone did not cause sensors to become saturated with water. However, the rates of drying indicated by the sensors after an initial saturation were inversely related to the relative humidity. On-site testing of the relative-humidity probe and the gypsum-coated ciruit grid indicated that they respond to a diurnal wetting and drying cycle; the limestone-block resistor responded only to rainfall.

An LOD with improved breakdown voltage in full-frame CCD devices

NASA Astrophysics Data System (ADS)

Banghart, Edmund K.; Stevens, Eric G.; Doan, Hung Q.; Shepherd, John P.; Meisenzahl, Eric J.

2005-02-01

In full-frame image sensors, lateral overflow drain (LOD) structures are typically formed along the vertical CCD shift registers to provide a means for preventing charge blooming in the imager pixels. In a conventional LOD structure, the n-type LOD implant is made through the thin gate dielectric stack in the device active area and adjacent to the thick field oxidation that isolates the vertical CCD columns of the imager. In this paper, a novel LOD structure is described in which the n-type LOD impurities are placed directly under the field oxidation and are, therefore, electrically isolated from the gate electrodes. By reducing the electrical fields that cause breakdown at the silicon surface, this new structure permits a larger amount of n-type impurities to be implanted for the purpose of increasing the LOD conductivity. As a consequence of the improved conductance, the LOD width can be significantly reduced, enabling the design of higher resolution imaging arrays without sacrificing charge capacity in the pixels. Numerical simulations with MEDICI of the LOD leakage current are presented that identify the breakdown mechanism, while three-dimensional solutions to Poisson's equation are used to determine the charge capacity as a function of pixel dimension.

An Automatic Critical Care Urine Meter

PubMed Central

Otero, Abraham; Fernández, Roemi; Apalkov, Andrey; Armada, Manuel

2012-01-01

Nowadays patients admitted to critical care units have most of their physiological parameters measured automatically by sophisticated commercial monitoring devices. More often than not, these devices supervise whether the values of the parameters they measure lie within a pre-established range, and issue warning of deviations from this range by triggering alarms. The automation of measuring and supervising tasks not only discharges the healthcare staff of a considerable workload but also avoids human errors in these repetitive and monotonous tasks. Arguably, the most relevant physiological parameter that is still measured and supervised manually by critical care unit staff is urine output (UO). In this paper we present a patent-pending device that provides continuous and accurate measurements of patient's UO. The device uses capacitive sensors to take continuous measurements of the height of the column of liquid accumulated in two chambers that make up a plastic container. The first chamber, where the urine inputs, has a small volume. Once it has been filled it overflows into a second bigger chamber. The first chamber provides accurate UO measures of patients whose UO has to be closely supervised, while the second one avoids the need for frequent interventions by the nursing staff to empty the container. PMID:23201988

Calibration of a two-dimensional hydrodynamic model for parts of the Allegheny, Monongahela, and Ohio Rivers, Allegheny County, Pennsylvania

USGS Publications Warehouse

Fulton, John W.; Wagner, Chad R.

2014-01-01

The U.S. Geological Survey (USGS), in cooperation with the Allegheny County Sanitary Authority, developed a validated two-dimensional Resource Management Associates2 (RMA2) hydrodynamic model of parts of the Allegheny, Monongahela, and Ohio Rivers (Three Rivers) to help assess the effects of combined sewer overflows (CSOs) and sanitary sewer overflows (SSOs) on the rivers. The hydrodynamic model was used to drive a water-quality model of the study area that was capable of simulating the transport and fate of fecal-indicator bacteria and chemical constituents under open-water conditions. The study area includes 14 tributary streams and parts of the Three Rivers where they enter and exit Allegheny County, an area of approximately 730 square miles (mi2). The city of Pittsburgh is near the center of the county, where the Allegheny and Monongahela Rivers join to form the headwaters of the Ohio River. The Three Rivers are regulated by a series of fixed-crest dams, gated dams, and radial (tainter) gates and serve as the receiving waters for tributary streams, CSOs, and SSOs. The RMA2 model was separated into four individual segments on the basis of the U.S. Army Corps of Engineers navigational pools in the study area (Dashields; Emsworth; Allegheny River, Pool 2; and Braddock), which were calibrated individually using measured water-surface slope, velocity, and discharge during high- and low-flow conditions. The model calibration process included the comparison of water-surface elevations at five locations and velocity profiles at more than 80 cross sections in the study area. On the basis of the calibration and validation results that included water-surface elevations and velocities, the model is a representative simulation of the Three Rivers flow patterns for discharges ranging from 4,050 to 47,400 cubic feet per second (ft3/s) on the Allegheny River, 2,550 to 40,000 ft3/s on the Monongahela River, and 10,900 to 99,000 ft3/s on the Ohio River. The Monongahela River was characterized by unsteady conditions during low and high flows, which affected the calibration range. The simulated low-flow water-surface elevations typically were within 0.2 feet (ft) of measured values, whereas the simulated high-flow water-surface elevations were typically within 0.3 ft of the measured values. The mean error between simulated and measured velocities was less than 0.07 ft/s for low-flow conditions and less than 0.17 ft/s for high-flow conditions.

The Development of a Gas–Liquid Two-Phase Flow Sensor Applicable to CBM Wellbore Annulus

PubMed Central

Wu, Chuan; Wen, Guojun; Han, Lei; Wu, Xiaoming

2016-01-01

The measurement of wellbore annulus gas–liquid two-phase flow in CBM (coalbed methane) wells is of great significance for reasonably developing gas drainage and extraction processes, estimating CBM output, judging the operating conditions of CBM wells and analyzing stratum conditions. Hence, a specially designed sensor is urgently needed for real-time measurement of gas–liquid two-phase flow in CBM wellbore annulus. Existing flow sensors fail to meet the requirements of the operating conditions of CBM wellbore annulus due to such factors as an inapplicable measurement principle, larger size, poor sealability, high installation accuracy, and higher requirements for fluid media. Therefore, based on the principle of a target flowmeter, this paper designs a new two-phase flow sensor that can identify and automatically calibrate different flow patterns of two-phase flows. Upon the successful development of the new flow sensor, lab and field tests were carried out, and the results show that the newly designed sensor, with a measurement accuracy of ±2.5%, can adapt to the operating conditions of CBM wells and is reliable for long-term work. PMID:27869708

The Development of a Gas-Liquid Two-Phase Flow Sensor Applicable to CBM Wellbore Annulus.

PubMed

Wu, Chuan; Wen, Guojun; Han, Lei; Wu, Xiaoming

2016-11-18

The measurement of wellbore annulus gas-liquid two-phase flow in CBM (coalbed methane) wells is of great significance for reasonably developing gas drainage and extraction processes, estimating CBM output, judging the operating conditions of CBM wells and analyzing stratum conditions. Hence, a specially designed sensor is urgently needed for real-time measurement of gas-liquid two-phase flow in CBM wellbore annulus. Existing flow sensors fail to meet the requirements of the operating conditions of CBM wellbore annulus due to such factors as an inapplicable measurement principle, larger size, poor sealability, high installation accuracy, and higher requirements for fluid media. Therefore, based on the principle of a target flowmeter, this paper designs a new two-phase flow sensor that can identify and automatically calibrate different flow patterns of two-phase flows. Upon the successful development of the new flow sensor, lab and field tests were carried out, and the results show that the newly designed sensor, with a measurement accuracy of ±2.5%, can adapt to the operating conditions of CBM wells and is reliable for long-term work.

Characteristics of active spectral sensor for plant sensing

USDA-ARS?s Scientific Manuscript database

Plant stress has been estimated by spectral signature using both passive and active sensors. As optical sensors measure reflected light from a target, changes in illumination conditions critically affect sensor response. Active spectral sensors minimize the illumination effects by producing their ...

Active spectral sensor evaluation under varying conditions

USDA-ARS?s Scientific Manuscript database

Plant stress has been estimated by spectral signature using both passive and active sensors. As optical sensors measure reflected light from a target, changes in illumination characteristics critically affect sensor response. Active sensors are of benefit in minimizing uncontrolled illumination effe...

Gravimetric system using high-speed double switching valves for low liquid flow rates

NASA Astrophysics Data System (ADS)

Cheong, Kar-Hooi; Doihara, Ryouji; Shimada, Takashi; Terao, Yoshiya

2018-07-01

This paper presents a gravimetric system developed to perform the static weighing with flying-start-and-stop (SW-FSS) calibration method at low liquid flow rates using a pair of identical high-speed switching valves as a flow diverter. Features of the gravimetric system comprise three main components: a pair of switching valves that divert the working liquid between two symmetrical flow paths; a weighing vessel equipped with an overflow inner vessel and enclosed in a weighing chamber; and a liquid discharge mechanism comprising a discharge tube and a discharge pump, used with a multi-purpose bin. These are described with an explanation of the design considerations behind each feature. The overflow inner vessel is designed with a notch in its wall and is positioned so that it does not come into contact with the liquid surface of the accumulated liquid in the weighing vessel or the side wall of the weighing vessel to obtain a good repeatability of the interactive effects between the feeding tube and the submerging working liquid, thus ensuring a correct mass reading of the liquid collection. A performance test showed that, in terms of contribution to the overall uncertainty of the standard flow rate, the pair of switching valves is capable of performing SW-FSS satisfactorily with small relative timing errors within %. However, the mass loss due to evaporation is considered a major source of error of the gravimetric system, showing a maximum error of 0.011% under the most evaporative condition tested for the longest liquid collection time of the gravimetric system.

Ice Jams the Ob River

NASA Technical Reports Server (NTRS)

2007-01-01

Russia's Ob River flows from south to north, and each summer, it thaws in the same direction. The result is that an ice jam sits downstream from thawed portions of the river, which is laden with heavy runoff from melted snow. On June 29, 2007, the Moderate Resolution Imaging Spectroradiometer (MODIS) flying on NASA's Terra satellite captured this image of the almost completely thawed Ob River. The scene is typical for early summer. South of the ice jam, the Gulf of Ob is swollen with pent-up run-off, and upstream from that, the river is widened as well. Unable to carve through frozen land, the river has little choice but to overflow its banks. For a comparison of early summer and autumn conditions, see Flooding on the Ob River in the Earth Observatory's Natural Hazards section. Besides the annual overflow, this image captures other circumstances of early summer. Sea ice is retreating from the Kara Sea. A lingering line of snow cover snakes its way along the Ob River, to the west. And while the land is lush and green in the south, it appears barren and brown in the north. Near the mouth of the river and the Kara Sea, the land is cold-adapted tundra, with diminutive plants and a short growing season. Just as the ice plugging the river had yet to thaw in the Far North's short summer, the tundra had not yet to greened up either. In this image it still appears lifeless beige. NASA image courtesy Jeff Schmaltz, MODIS Rapid Response Team, Goddard Space Flight Center

Model Based Optimal Sensor Network Design for Condition Monitoring in an IGCC Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Rajeeva; Kumar, Aditya; Dai, Dan

2012-12-31

This report summarizes the achievements and final results of this program. The objective of this program is to develop a general model-based sensor network design methodology and tools to address key issues in the design of an optimal sensor network configuration: the type, location and number of sensors used in a network, for online condition monitoring. In particular, the focus in this work is to develop software tools for optimal sensor placement (OSP) and use these tools to design optimal sensor network configuration for online condition monitoring of gasifier refractory wear and radiant syngas cooler (RSC) fouling. The methodology developedmore » will be applicable to sensing system design for online condition monitoring for broad range of applications. The overall approach consists of (i) defining condition monitoring requirement in terms of OSP and mapping these requirements in mathematical terms for OSP algorithm, (ii) analyzing trade-off of alternate OSP algorithms, down selecting the most relevant ones and developing them for IGCC applications (iii) enhancing the gasifier and RSC models as required by OSP algorithms, (iv) applying the developed OSP algorithm to design the optimal sensor network required for the condition monitoring of an IGCC gasifier refractory and RSC fouling. Two key requirements for OSP for condition monitoring are desired precision for the monitoring variables (e.g. refractory wear) and reliability of the proposed sensor network in the presence of expected sensor failures. The OSP problem is naturally posed within a Kalman filtering approach as an integer programming problem where the key requirements of precision and reliability are imposed as constraints. The optimization is performed over the overall network cost. Based on extensive literature survey two formulations were identified as being relevant to OSP for condition monitoring; one based on LMI formulation and the other being standard INLP formulation. Various algorithms to solve these two formulations were developed and validated. For a given OSP problem the computation efficiency largely depends on the “size” of the problem. Initially a simplified 1-D gasifier model assuming axial and azimuthal symmetry was used to test out various OSP algorithms. Finally these algorithms were used to design the optimal sensor network for condition monitoring of IGCC gasifier refractory wear and RSC fouling. The sensors type and locations obtained as solution to the OSP problem were validated using model based sensing approach. The OSP algorithm has been developed in a modular form and has been packaged as a software tool for OSP design where a designer can explore various OSP design algorithm is a user friendly way. The OSP software tool is implemented in Matlab/Simulink© in-house. The tool also uses few optimization routines that are freely available on World Wide Web. In addition a modular Extended Kalman Filter (EKF) block has also been developed in Matlab/Simulink© which can be utilized for model based sensing of important process variables that are not directly measured through combining the online sensors with model based estimation once the hardware sensor and their locations has been finalized. The OSP algorithm details and the results of applying these algorithms to obtain optimal sensor location for condition monitoring of gasifier refractory wear and RSC fouling profile are summarized in this final report.« less

Sensor Web in Antarctica: Developing an Intelligent, Autonomous Platform for Locating Biological Flourishes in Cryogenic Environments

NASA Technical Reports Server (NTRS)

Delin, K. A.; Harvey, R. P.; Chabot, N. A.; Jackson, S. P.; Adams, Mike; Johnson, D. W.; Britton, J. T.

2003-01-01

The most rigorous tests of the ability to detect extant life will occur where biotic activity is limited by severe environmental conditions. Cryogenic environments are among the most severe-the energy and nutrients needed for biological activity are in short supply while the climate itself is actively destructive to biological mechanisms. In such settings biological activity is often limited to brief flourishes, occurring only when and where conditions are at their most favorable. The closer that typical regional conditions approach conditions that are actively hostile , the more widely distributed biological blooms will be in both time and space. On a spatial dimension of a few meters or a time dimension of a few days, biological activity becomes much more difficult to detect. One way to overcome this difficulty is to establish a Sensor Web that can monitor microclimates over appropriate scales of time and distance, allowing a continuous virtual presence for instant recognition of favorable conditions. A more sophisticated Sensor Web, incorporating metabolic sensors, can effectively meet the challenge to be in "the right place in the right time". This is particularly of value in planetary surface missions, where limited mobility and mission timelines require extremely efficient sample and data acquisition. Sensor Webs can be an effective way to fill the gap between broad scale orbital data collection and fine-scale surface lander science. We are in the process of developing an intelligent, distributed and autonomous Sensor Web that will allow us to monitor microclimate under severe cryogenic conditions, approaching those extant on the surface of Mars. Ultimately this Sensor Web will include the ability to detect and/or establish limits on extant microbiological activity through incorporation of novel metabolic gas sensors. Here we report the results of our first deployment of a Sensor Web prototype in a previously unexplored high altitude East Antarctic Plateau "micro-oasis" at the MacAlpine Hills, Law Glacier, Antarctica.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E; Svoboda, John M; West, Phillip B; Heath, Gail L; Scott, Clark L

2015-01-27

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E [Idaho Falls, ID; Svoboda, John M [Idaho Falls, ID; West, Phillip B [Idaho Falls, ID; Heath, Gail L [Iona, ID; Scott, Clark L [Idaho Falls, ID

2010-08-31

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Methods, apparatus, and systems for monitoring transmission systems

DOEpatents

Polk, Robert E; Svoboda, John M.; West, Phillip B.; Heath, Gail L.; Scott, Clark L.

2016-07-19

A sensing platform for monitoring a transmission system, and method therefor, may include a sensor that senses one or more conditions relating to a condition of the transmission system and/or the condition of an environment around the transmission system. A control system operatively associated with the sensor produces output data based on an output signal produced by the sensor. A transmitter operatively associated with the control system transmits the output data from the control system.

Fecal overflow often affects children with chronic constipation that appears after the age of 2 years.

PubMed

Kammacher Guerreiro, Mélissa; Bettinville, Aurore; Herzog, Denise

2014-08-01

Chronic functional constipation with or without encopresis is a common problem in the pediatric population, and the prevalence of encopresis may be underestimated. The aim of this study was to assess the prevalence and risk factors for overflow incontinence in patients with chronic constipation seen at a pediatric gastroenterology consultation. A retrospective study of 270 files of patients seen between 1997 and 2012 was conducted, and a classification according to Rome III criteria was done. Among 145 (53.7%) boys and 125 (46.2%) girls, 117 had overflow incontinence (43.3%) - 41 (35%) girls and 76 (65%) boys. The first symptoms of chronic constipation appeared at a median age of 30 and 33 months in encopretic and 16 and 12 months in nonencopretic girls and boys, respectively. The first specialized consultation took place after a median disease duration of 26.5 and 24 months in encopretic and 16 and 9 months in nonencopretic girls and boys, respectively. A history of stool retention and the presence of scybala at examination, but not of pain at defecation or anal fissure, were associated with encopresis. The onset of chronic constipation after the age of 2 years, a longer disease duration, male gender, and a history of stool retention were seen as risk factors for the development of encopresis in patients with chronic functional constipation. © The Author(s) 2014.

Quantification of Interbasin Transfers into the Addicks Reservoir during Hurricane Harvey

NASA Astrophysics Data System (ADS)

Sebastian, A.; Juan, A.; Gori, A.; Maulsby, F.; Bedient, P. B.

2017-12-01

Between August 25 and 30, Hurricane Harvey dropped unprecedented rainfall over southeast Texas causing widespread flooding in the City of Houston. Water levels in the Addicks and Barker reservoirs, built in the 1940s to protect downtown Houston, exceeded previous records by approximately 2 meters. Concerns regarding structural integrity of the dams and damage to neighbourhoods in within the reservoir pool resulted in controlled releases into Buffalo Bayou, flooding an estimated 4,000 additional structures downstream of the dams. In 2016, during the Tax Day it became apparent that overflows from Cypress Creek in northern Harris County substantially contribute to water levels in Addicks. Prior to this event, little was known about the hydrodynamics of this overflow area or about the additional stress placed on Addicks and Barker reservoirs due to the volume of overflow. However, this information is critical for determining flood risk in Addicks Watershed, and ultimately Buffalo Bayou. In this study, we utilize the recently developed HEC-RAS 2D model the interbasin transfer that occurs between Cypress Creek Watershed and Addicks Reservoir to quantify the volume and rate at which water from Cypress enters the reservoir during extreme events. Ultimately, the results of this study will help inform the official hydrologic models used by HCFCD to determine reservoir operation during future storm events and better inform residents living in or above the reservoir pool about their potential flood risk.

Studies of the inner shelf and coastal sedimentation environment of the Beaufort Sea from ERTS-1

NASA Technical Reports Server (NTRS)

Reimnitz, E. (Principal Investigator)

1972-01-01

The author has identified the following significant results. Field studies of the initiation of river flow onto the frozen Arctic Ocean were made by a group of scientists from May 15 to June 10, 1972. A time lapse camera mounted on a 40-ft. tower near the mouth of the Kaparuk River, west of Prudhoe Bay, provided a detailed 10-day record (24 hours a day) of flow direction and water level. It is believed that wind build-up, discharge variance of the river, and through-ice drainage rates are the prime factors influencing overflow onto the sea ice. Current meter, transmissometer, temperature, salinity, and thermoprobe data were collected from holes drilled in the shorefast ice from seal holes and from the river water overflow. Depth and a real distribution of the overflow water were monitored from the ice using snowmobiles, and from the air using helicopters and fixed-wing aircraft. Photographic records were made on 35mm KII, KX, Ektachrome IR, Plus X, and IR black and white film. A simple two camera frame permitted simultaneous exposures of two types of film. Preliminary comparisons of the IR and conventional films, both color and black and white, showed no advantage to using the infrared film. However, the low altitude photography taken during this study will be very helpful in the interpretation of ERTS-1 imagery.

Nuclear sensor signal processing circuit

DOEpatents

Kallenbach, Gene A [Bosque Farms, NM; Noda, Frank T [Albuquerque, NM; Mitchell, Dean J [Tijeras, NM; Etzkin, Joshua L [Albuquerque, NM

2007-02-20

An apparatus and method are disclosed for a compact and temperature-insensitive nuclear sensor that can be calibrated with a non-hazardous radioactive sample. The nuclear sensor includes a gamma ray sensor that generates tail pulses from radioactive samples. An analog conditioning circuit conditions the tail-pulse signals from the gamma ray sensor, and a tail-pulse simulator circuit generates a plurality of simulated tail-pulse signals. A computer system processes the tail pulses from the gamma ray sensor and the simulated tail pulses from the tail-pulse simulator circuit. The nuclear sensor is calibrated under the control of the computer. The offset is adjusted using the simulated tail pulses. Since the offset is set to zero or near zero, the sensor gain can be adjusted with a non-hazardous radioactive source such as, for example, naturally occurring radiation and potassium chloride.

A Sensor System for Detection of Hull Surface Defects

PubMed Central

Navarro, Pedro; Iborra, Andrés; Fernández, Carlos; Sánchez, Pedro; Suardíaz, Juan

2010-01-01

This paper presents a sensor system for detecting defects in ship hull surfaces. The sensor was developed to enable a robotic system to perform grit blasting operations on ship hulls. To achieve this, the proposed sensor system captures images with the help of a camera and processes them in real time using a new defect detection method based on thresholding techniques. What makes this method different is its efficiency in the automatic detection of defects from images recorded in variable lighting conditions. The sensor system was tested under real conditions at a Spanish shipyard, with excellent results. PMID:22163590

Optical fiber sensor of partial discharges in High Voltage DC experiments

NASA Astrophysics Data System (ADS)

Búa-Núñez, I.; Azcárraga-Ramos, C. G.; Posada-Román, J. E.; Garcia-Souto, J. A.

2014-05-01

A setup simulating High Voltage DC (HVDC) transformers barriers was developed to demonstrate the effectiveness of an optical fiber (OF) sensor in detecting partial discharges (PD) under these peculiar conditions. Different PD detection techniques were compared: electrical methods, and acoustic methods. Standard piezoelectric sensors (R15i-AST) and the above mentioned OF sensors were used for acoustic detection. The OF sensor was able to detect PD acoustically with a sensitivity better than the other detection methods. The multichannel instrumentation system was tested in real HVDC conditions with the aim of analyzing the behavior of the insulation (mineral oil/pressboard).

Wirelessly Interrogated Position or Displacement Sensors

NASA Technical Reports Server (NTRS)

Woodard, Stanley E.; Taylor, Bryant D.

2007-01-01

Two simple position or displacement sensors based on inductance-capacitance resonant circuits have been conceived. These sensors are both powered and interrogated without use of wires and without making contact with other objects. Instead, excitation and interrogation are accomplished by means of a magnetic-field-response recorder. Both of the present position or displacement sensors consist essentially of variable rectangular parallel-plate capacitors electrically connected in series with fixed inductors. Simple inductance-capacitance circuits of the type used in these sensors are inherently robust; their basic mode of operation does not depend on maintenance of specific environmental conditions. Hence, these sensors can be used under such harsh conditions as cryogenic temperatures, high pressures, and radioactivity.

Magnitude and frequency of flooding on the Myakka River, Southwest Florida

USGS Publications Warehouse

Hammett, K.M.; Turner, J.F.; Murphy, W.R.

1978-01-01

Increasing numbers of urban and agricultural developments are being located on waterfront property in the Myakka River flood plain in southwest Florida. Under natural conditions, a large depression, Tatum Sawgrass, was available as a flood storage area in the upper Myakka River basin. Construction of dikes across the lower part of Tatum Sawgrass has restricted use of the depression for temporary storage of Myakka River flood water overflow, and has resulted in increased flood-peak discharges and flood heights in downstream reaches of the Myakka River. The difference between natural and diked condition flood-peak discharges and flood heights is presented to illustrate the effects of the dikes. Flood-peak discharges, water-surface elevations and flood profiles also are provided for diked conditions. Analytical procedures used to evaluate diking effects are described in detail. The study reach includes Myakka River main stem upstream from U.S. Highway 41, near Myakka Shores in Sarasota County, to State Road 70 near Myakka City in Manatee County (including Tatum Sawgrass and Clay Gully), and Blackburn Canal from Venice By-Way to Myakka River. (Woodard-USGS)

Assessing the water quality response to an alternative sewage disposal strategy at bathing sites on the east coast of Ireland.

PubMed

Bedri, Zeinab; O'Sullivan, John J; Deering, Louise A; Demeter, Katalin; Masterson, Bartholomew; Meijer, Wim G; O'Hare, Gregory

2015-02-15

A three-dimensional model is used to assess the bathing water quality of Bray and Killiney bathing sites in Ireland following changes to the sewage management system. The model, firstly calibrated to hydrodynamic and water quality data from the period prior to the upgrade of the Wastewater Treatment Works (WwTW), was then used to simulate Escherichia coli (E. coli) distributions for discharge scenarios of the periods prior to and following the upgrade of the WwTW under dry and wet weather conditions. E. coli distributions under dry weather conditions demonstrate that the upgrade in the WwTW has remarkably improved the bathing water quality to a Blue Flag status. The new discharge strategy is expected to drastically reduce the rainfall-related incidents in which environmental limits of the Bathing Water Directive are breached. However, exceedances to these limits may still occur under wet weather conditions at Bray bathing site due to storm overflows that may still be discharged through two sea outfalls offshore of Bray bathing site. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Structure Design of Piezoelectric Poly(vinylidene Fluoride) (PVDF) Polymer-Based Sensor Patch for the Respiration Monitoring under Dynamic Walking Conditions.

PubMed

Lei, Kin-Fong; Hsieh, Yi-Zheng; Chiu, Yi-Yuan; Wu, Min-Hsien

2015-07-31

This study reports a piezoelectric poly(vinylidene fluoride) (PVDF) polymer-based sensor patch for respiration detections in dynamic walking condition. The working mechanism of respiration signal generation is based on the periodical deformations on a human chest wall during the respiratory movements, which in turn mechanically stretch the piezoelectric PVDF film to generate the corresponding electrical signals. In this study, the PVDF sensing film was completely encapsulated within the sensor patch forming a mass-spring-damper mechanical system to prevent the noises generated in a dynamic condition. To verify the design of sensor patch to prevent dynamic noises, experimental investigations were carried out. Results demonstrated the respiration signals generated and the respiratory rates measured by the proposed sensor patch were in line with the same measurements based on a commercial respiratory effort transducer both in a static (e.g., sitting) or dynamic (e.g., walking) condition. As a whole, this study has developed a PVDF-based sensor patch which is capable of monitoring respirations in a dynamic walking condition with high fidelity. Other distinctive features include its small size, light weight, ease of use, low cost, and portability. All these make it a promising sensing device to monitor respirations particularly in home care units.

A High-Temperature Piezoresistive Pressure Sensor with an Integrated Signal-Conditioning Circuit

PubMed Central

Yao, Zong; Liang, Ting; Jia, Pinggang; Hong, Yingping; Qi, Lei; Lei, Cheng; Zhang, Bin; Xiong, Jijun

2016-01-01

This paper focuses on the design and fabrication of a high-temperature piezoresistive pressure sensor with an integrated signal-conditioning circuit, which consists of an encapsulated pressure-sensitive chip, a temperature compensation circuit and a signal-conditioning circuit. A silicon on insulation (SOI) material and a standard MEMS process are used in the pressure-sensitive chip fabrication, and high-temperature electronic components are adopted in the temperature-compensation and signal-conditioning circuits. The entire pressure sensor achieves a hermetic seal and can be operated long-term in the range of −50 °C to 220 °C. Unlike traditional pressure sensor output voltage ranges (in the dozens to hundreds of millivolts), the output voltage of this sensor is from 0 V to 5 V, which can significantly improve the signal-to-noise ratio and measurement accuracy in practical applications of long-term transmission based on experimental verification. Furthermore, because this flexible sensor’s output voltage is adjustable, general follow-up pressure transmitter devices for voltage converters need not be used, which greatly reduces the cost of the test system. Thus, the proposed high-temperature piezoresistive pressure sensor with an integrated signal-conditioning circuit is expected to be highly applicable to pressure measurements in harsh environments. PMID:27322288

76 FR 45399 - Special Conditions: Cessna Aircraft Company, Model LC40-550FG, LC41-550FG, and LC42-550FG; AmSafe...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-29

... lap belt. The inflatable portion of the restraint system will rely on sensors to electronically... establishing these special conditions. The inflatable restraint system relies on sensors to electronically activate the inflator for deployment. These sensors could be susceptible to inadvertent activation, causing...

An investigation on wireless sensors for asset management and health monitoring of civil structures

NASA Astrophysics Data System (ADS)

Furkan, Mustafa; Mao, Qiang; Mazzotti, Matteo; DeVitis, John; Sumitro, S. Paul; Faridazar, Fred; Aktan, A. Emin; Moon, Franklin; Bartoli, Ivan

2016-04-01

Application of wireless sensors and sensor networks for Structural Health Monitoring has been investigated for a long time. Key limitations for practical use are energy requirements, connectivity, and integration with existing systems. Current sensors and sensor networks mainly rely on wired connectivity for communication and external power source for energy. This paper presents a suite of wireless sensors that are low-cost, maintenance free, rugged, and have long service life. The majority of the sensors considered were designed by transforming existing, proven, and robust wired sensors into wireless units. In this study, the wireless sensors were tested in laboratory conditions for calibration and evaluation along with wired sensors. The experimental results were also compared to theoretical results. The tests mostly show satisfactory performance of the wireless units. This work is part of a broader Federal Highway Administration sponsored project intended to ultimately validate a wireless sensing system on a real, operating structure to account for all the uncertainties, environmental conditions and operational variability that are encountered in the field.

Performance of an Advanced Stirling Convertor Based on Heat Flux Sensor Measurements

NASA Technical Reports Server (NTRS)

Wilson, Dcott D.

2012-01-01

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two highefficiency Advanced Stirling Convertors (ASCs), developed by Sunpower, Inc., and NASA Glenn Research Center. The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot-end and cold-end temperatures, and specified electrical power output for a given heat input. It is difficult to measure heat input to Stirling convertors due to the complex geometries of the hot components, temperature limits of sensor materials, and invasive integration of sensors. A thin-film heat flux sensor was used to directly measure heat input to an ASC. The effort succeeded in designing and fabricating unique sensors, which were integrated into a Stirling convertor ground test and exposed to test temperatures exceeding 700 C in air for 10,000 hr. Sensor measurements were used to calculate thermal efficiency for ASC-E (Engineering Unit) #1 and #4. The post-disassembly condition of the sensors is also discussed.

Performance of an Advanced Stirling Convertor Based on Heat Flux Sensor Measurements

NASA Technical Reports Server (NTRS)

Wilson, Scott D.

2012-01-01

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two high-efficiency Advanced Stirling Convertors (ASCs), developed by Sunpower, Inc., and NASA Glenn Research Center. The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot-end and cold-end temperatures, and specified electrical power output for a given heat input. It is difficult to measure heat input to Stirling convertors due to the complex geometries of the hot components, temperature limits of sensor materials, and invasive integration of sensors. A thin-film heat flux sensor was used to directly measure heat input to an ASC. The effort succeeded in designing and fabricating unique sensors, which were integrated into a Stirling convertor ground test and exposed to test temperatures exceeding 700 C in air for 10,000 hr. Sensor measurements were used to calculate thermal efficiency for ASC-E (Engineering Unit) #1 and #4. The post-disassembly condition of the sensors is also discussed.

Reconstruction of in-plane strain maps using hybrid dense sensor network composed of sensing skin

NASA Astrophysics Data System (ADS)

Downey, Austin; Laflamme, Simon; Ubertini, Filippo

2016-12-01

The authors have recently developed a soft-elastomeric capacitive (SEC)-based thin film sensor for monitoring strain on mesosurfaces. Arranged in a network configuration, the sensing system is analogous to a biological skin, where local strain can be monitored over a global area. Under plane stress conditions, the sensor output contains the additive measurement of the two principal strain components over the monitored surface. In applications where the evaluation of strain maps is useful, in structural health monitoring for instance, such signal must be decomposed into linear strain components along orthogonal directions. Previous work has led to an algorithm that enabled such decomposition by leveraging a dense sensor network configuration with the addition of assumed boundary conditions. Here, we significantly improve the algorithm’s accuracy by leveraging mature off-the-shelf solutions to create a hybrid dense sensor network (HDSN) to improve on the boundary condition assumptions. The system’s boundary conditions are enforced using unidirectional RSGs and assumed virtual sensors. Results from an extensive experimental investigation demonstrate the good performance of the proposed algorithm and its robustness with respect to sensors’ layout. Overall, the proposed algorithm is seen to effectively leverage the advantages of a hybrid dense network for application of the thin film sensor to reconstruct surface strain fields over large surfaces.

Inexpensive programmable clock for a 12-bit computer

NASA Technical Reports Server (NTRS)

Vrancik, J. E.

1972-01-01

An inexpensive programmable clock was built for a digital PDP-12 computer. The instruction list includes skip on flag; clear the flag, clear the clock, and stop the clock; and preset the counter with the contents of the accumulator and start the clock. The clock counts at a rate determined by an external oscillator and causes an interrupt and sets a flag when a 12-bit overflow occurs. An overflow can occur after 1 to 4096 counts. The clock can be built for a total parts cost of less than $100 including power supply and I/O connector. Slight modification can be made to permit its use on larger machines (16 bit, 24 bit, etc.) and logic level shifting can be made to make it compatible with any computer.

Subjectivity: A Case of Biological Individuation and an Adaptive Response to Informational Overflow

PubMed Central

Jonkisz, Jakub

2016-01-01

The article presents a perspective on the scientific explanation of the subjectivity of conscious experience. It proposes plausible answers for two empirically valid questions: the ‘how’ question concerning the developmental mechanisms of subjectivity, and the ‘why’ question concerning its function. Biological individuation, which is acquired in several different stages, serves as a provisional description of how subjective perspectives may have evolved. To the extent that an individuated informational space seems the most efficient way for a given organism to select biologically valuable information, subjectivity is deemed to constitute an adaptive response to informational overflow. One of the possible consequences of this view is that subjectivity might be (at least functionally) dissociated from consciousness, insofar as the former primarily facilitates selection, the latter action. PMID:27555835

Development of a Response Planner using the UCT Algorithm for Cyber Defense

DTIC Science & Technology

2013-03-01

writer2l, guess passwd r2l, imap r2l, ipsweep probe, land dos, loadmodule u2r, multihop r2l, neptune dos, nmap probe, perl u2r, phf r2l, pod dos, portsweep...2646 10 pod 201 11 back 956 12 guess passwd 53 Item Type Count 13 ftp write 8 14 multihop 7 15 rootkit 10 16 buffer overflow 30 17 imap 11 18...pod 0 0 0 87 6 11 0 0 64 33 0 0 0 0 k = back 908 0 0 0 0 0 0 0 0 0 47 0 1 0 l = guess passwd 0 0 0 42 3 0 1 0 0 0 0 5 1 0 m = buffer overflow 0 0 17

Real time control of a combined sewer system using radar-measured precipitation--results of the pilot study.

PubMed

Petruck, A; Holtmeier, E; Redder, A; Teichgräber, B

2003-01-01

Emschergenossenschaft and Lippeverband have developed a method to use radar-measured precipitation as an input for a real-time control of a combined sewer system containing several overflow structures. Two real-time control strategies have been developed and tested, one is solely volume-based, the other is volume and pollution-based. The system has been implemented in a pilot study in Gelsenkirchen, Germany. During the project the system was optimised and is now in constant operation. It was found, that the volume of combined sewage overflow could be reduced by 5 per cent per year. This was also found in simulations carried out in similar catchment areas. Most of the potential of improvement can already be achieved by local pollution-based control strategies.

Optimal Magnetic Sensor Vests for Cardiac Source Imaging

PubMed Central

Lau, Stephan; Petković, Bojana; Haueisen, Jens

2016-01-01

Magnetocardiography (MCG) non-invasively provides functional information about the heart. New room-temperature magnetic field sensors, specifically magnetoresistive and optically pumped magnetometers, have reached sensitivities in the ultra-low range of cardiac fields while allowing for free placement around the human torso. Our aim is to optimize positions and orientations of such magnetic sensors in a vest-like arrangement for robust reconstruction of the electric current distributions in the heart. We optimized a set of 32 sensors on the surface of a torso model with respect to a 13-dipole cardiac source model under noise-free conditions. The reconstruction robustness was estimated by the condition of the lead field matrix. Optimization improved the condition of the lead field matrix by approximately two orders of magnitude compared to a regular array at the front of the torso. Optimized setups exhibited distributions of sensors over the whole torso with denser sampling above the heart at the front and back of the torso. Sensors close to the heart were arranged predominantly tangential to the body surface. The optimized sensor setup could facilitate the definition of a standard for sensor placement in MCG and the development of a wearable MCG vest for clinical diagnostics. PMID:27231910

Hydraulic description of a flood event with optical remote sensors: a constructive constraint on modelling uncertainties

NASA Astrophysics Data System (ADS)

Battiston, Stéphanie; Allenbach, Bernard

2010-05-01

The exceptional characteristics of the December 2003 Rhône flood event (particularly high water flows, extent of the affected area, important damages especially in the region of Arles) make it be considered as a reference flood episode of this French river and a very well-known event. During the crisis, the International Charter "Space and Major Disasters" was triggered by the French Civil Protection for the rapid mapping of the flooding using Earth Observation imagery in order to facilitate crisis operations. As a result, more than 60 satellite images covering the flood were acquired over a 10 days period following the peak flow. Using the opportunity provided by this incomparable data coverage, the French Ministry of the Environment ordered a study on the evaluation of remote sensing's potential benefits for flood management. One of the questions asked by the risk managers was: what type of flood information can be provided by the different remote sensing platforms? Elements of response were delivered mainly in the form of a comprehensive compilation of maps and illustrations, displaying the main hydraulic elements (static ones as well as dynamic ones), initially listed and requested by hydrologists (more precisely, by a regional engineering society specialised in hydraulics and hydrology and in charge of a field campaign during the event), observed on different optical images of the flood event having affected the plain between Tarascon (upstream) and Arles (downstream). It is seen that a careful mapping of all flood traces visible on remote sensing event imagery - apparent water, moisture traces, breaches, overflows, stream directions, impermeable boundaries … - delivers a valuable vision of the flood's occurrence combining accuracy and comprehensiveness. In fact, optical imagery offers a detailed vision of the event : moisture traces complete flood traces extent; the observation of draw-off directions through waterproof barriers reveals hydraulic compartments; high resolution optical imagery allow the exhaustive inventory of breaches and overflows; turbidity variations and draw-off give information on stream directions. These facts are of primary interest to help in deriving a firm understanding of the flooding processes, but also comprise a powerful source for the necessary parameterization and/or calibration of hydraulic models. Thus the accuracy of flood extents derived from remote sensing data could, on the one hand, be valuable inputs to historical flood info-bases within overall risk-linked databases, and on the other hand, test the validity of hydrological modelling, while helping to lift equifinality uncertainties. These first investigations highlight that space imagery of events constitutes an unrivalled tool for flood disaster observation. This 2D record is complementary to all field measurements and the integration of "space derived flood products" is valuable for all stages of risk management. This potential of EO optical sensors for flood monitoring is also confirmed in a detailed analysis making a qualitative and quantitative evaluation of the results, confronting ten optical and radar remote sensing platforms with field observations.

COMSOL-Based Modeling and Simulation of SnO2/rGO Gas Sensor for Detection of NO2.

PubMed

Yaghouti Niyat, Farshad; Shahrokh Abadi, M H

2018-02-01

Despite SIESTA and COMSOL being increasingly used for the simulation of the sensing mechanism in the gas sensors, there are no modeling and simulation reports in literature for detection of NO 2 based rGO/SnO 2 sensors. In the present study, we model, simulate, and characterize an NO 2 based rGO/SnO 2 gas sensor using COMSOL by solving the Poisson's equations under associated boundary conditions of mass, heat and electrical transitions. To perform the simulation, we use an exposure model for presenting the required NO 2 , a heat transfer model to obtain a reaction temperature, and an electrical model to characterize the sensor's response in the presence of the gas. We characterize the sensor's response in the presence of different concentrations of NO 2 at different working temperatures and compare the results with the experimental data, reported by Zhang et al. The results from the simulated sensor show a good agreement with the real sensor with some inconsistencies due to differences between the practical conditions in the real chamber and applied conditions to the analytical equations. The results also show that the method can be used to define and predict the behavior of the rGO-based gas sensors before undergoing the fabrication process.

A novel textile characterisation approach using an embedded sensor system and segmented textile manipulation

NASA Astrophysics Data System (ADS)

Fial, Julian; Carosella, Stefan; Langheinz, Mario; Wiest, Patrick; Middendorf, Peter

2018-05-01

This paper investigates the application of sensors on carbon fibre textiles for the purpose of textile characterisation and draping process optimisation. The objective is to analyse a textile's condition during the draping operation and actively manipulate boundary conditions in order to create better preform qualities. Various realisations of textile integrated sensors are presented, focusing on the measurement of textile strain. Furthermore, a complex textile characterisation approach is presented where these sensors shall be implemented in.

Flexible DCP interface. [signal conditioning system for use with Kansas environmental sensors

NASA Technical Reports Server (NTRS)

Kanemasu, E. T. (Principal Investigator); Schimmelpfenning, H.

1974-01-01

The author has identified the following significant results. A user of an ERTS data collection system must supply the sensors and signal conditioning interface. The electronic interface must be compatible with the NASA-furnished data collection platform (DCP). A universal signal conditioning system for use with a wide range of environmental sensors is described. The interface is environmentally and electronically compatible with the DCP and has operated satisfactorily for a complete winter wheat growing season in Kansas.

QUANTIFICATION OF HEAT FLUX FROM A REACTING THERMITE SPRAY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eric Nixon; Michelle Pantoya

2009-07-01

Characterizing the combustion behaviors of energetic materials requires diagnostic tools that are often not readily or commercially available. For example, a jet of thermite spray provides a high temperature and pressure reaction that can also be highly corrosive and promote undesirable conditions for the survivability of any sensor. Developing a diagnostic to quantify heat flux from a thermite spray is the objective of this study. Quick response sensors such as thin film heat flux sensors can not survive the harsh conditions of the spray, but more rugged sensors lack the response time for the resolution desired. A sensor that willmore » allow for adequate response time while surviving the entire test duration was constructed. The sensor outputs interior temperatures of the probes at known locations and utilizes an inverse heat conduction code to calculate heat flux values. The details of this device are discussed and illustrated. Temperature and heat flux measurements of various thermite spray conditions are reported. Results indicate that this newly developed energetic material heat flux sensor provides quantitative data with good repeatability.« less

Impact of Temperature and UV Irradiation on Dynamics of NO2 Sensors Based on ZnO Nanostructures

PubMed Central

Pustelny, Tadeusz

2017-01-01

The main object of this study is the improvement of the dynamics of NO2 sensors based on ZnO nanostructures. Investigations presented in this paper showed that the combination of temperature and ultraviolet (UV) activation of the sensors can significantly decrease the sensor response and regeneration times. In comparison with the single activation method (elevated temperature or UV), these times for 1 ppm of NO2 decreased from about 10 min (or more) to less than 40 s. In addition, at the optimal conditions (200 °C and UV), sensors were very stable, were fully scalable (in the range on NO2 concentration of 1–20 ppm) and baseline drift was significantly reduced. Furthermore, in this paper, extensive studies of the influence of temperature and carrier gas (nitrogen and air) on NO2 sensing properties of the ZnO nanostructures were conducted. The NO2 sensing mechanisms of the sensors operating at elevated temperatures and under UV irradiation were also discussed. Our study showed that sensor responses to NO2 and response/regeneration times are comparable from sensor to sensor in air and nitrogen conditions, which suggests that the proposed simple technology connected with well-chosen operation conditions is repeatable. The estimated limit of detection of the sensors is within the level of ≈800 ppb in nitrogen and ≈700 ppb in air. PMID:29019924

A Tailored Ontology Supporting Sensor Implementation for the Maintenance of Industrial Machines

PubMed Central

Belkadi, Farouk; Bernard, Alain

2017-01-01

The longtime productivity of an industrial machine is improved by condition-based maintenance strategies. To do this, the integration of sensors and other cyber-physical devices is necessary in order to capture and analyze a machine’s condition through its lifespan. Thus, choosing the best sensor is a critical step to ensure the efficiency of the maintenance process. Indeed, considering the variety of sensors, and their features and performance, a formal classification of a sensor’s domain knowledge is crucial. This classification facilitates the search for and reuse of solutions during the design of a new maintenance service. Following a Knowledge Management methodology, the paper proposes and develops a new sensor ontology that structures the domain knowledge, covering both theoretical and experimental sensor attributes. An industrial case study is conducted to validate the proposed ontology and to demonstrate its utility as a guideline to ease the search of suitable sensors. Based on the ontology, the final solution will be implemented in a shared repository connected to legacy CAD (computer-aided design) systems. The selection of the best sensor is, firstly, obtained by the matching of application requirements and sensor specifications (that are proposed by this sensor repository). Then, it is refined from the experimentation results. The achieved solution is recorded in the sensor repository for future reuse. As a result, the time and cost of the design process of new condition-based maintenance services is reduced. PMID:28885592

2002 NPDES CSO Report to Congress

EPA Pesticide Factsheets

This report, delivered to Congress on January 29, 2002, identifies progress made in implementing and enforcing combined sewer overflow (CSO) controls prior to, and because of, the 1994 CSO control policy.

--No Title--

Science.gov Websites

.slide { position:relative; height:363px; width:858px; overflow:hidden; } .slideshow .description { box ; padding:16px; width:253px; height:331px; background-color:#393939; } .slideshow .description h2 { color

Research on the conductivity of a haptic sensor, especially with the sensor under extended condition

NASA Astrophysics Data System (ADS)

Zheng, Yaoyang; Shimada, Kunio

2008-11-01

The present paper describes the application of magnetic compound fluid (MCF) rubber as a haptic sensor for use as a material for robot sensors, artificial skin, and so on. MCF rubber is one of several new composite materials utilizing the MCF magnetic responsive fluid developed by Shimada. By applying MCF to silicon oil rubber, we can make MCF rubber highly sensitive to temperature and electric conduction. By mixing Cu and Ni particles in the silicon oil rubber and then applying a strong magnetic field, we can produce magnetic clusters at high density. The clusters form a network, as confirmed by optical observation. The MCF rubber with small deformations can act as an effective sensor. We report herein several experiments in which changes in the MCF rubber's resistance were observed when the rubber was compressed and a deformation was generated. We then made a trial haptic sensor using the MCF conductive rubber and performed many experiments to observe changes in the electrical resistance of the sensor. The experimental results showed that the proposed sensor made with MCF conductive rubber is useful for sensing small amounts of pressure or small deformations. Sometimes, however, the sensor rubber will be extended when we apply this sensor to the finger of the robot or an elbow. In these cases, it is necessary to understand the changes in sensor's conductivity. We therefore carried out some experiments to demonstrate how, under tensile conditions, the sensor's conductivity changes to a small value easier than the sensor in free condition. The results show that the sensors became more sensitive to the same pressure under extended conditions. In the present paper, we first describe the new type of functional fluid MCF rubber and a new composite material based on this MCF fluid. We then explain the production method for MCF conductive rubber and its conductive algorithm. Finally, we report our results regarding the MCF sensitivity when the MCF rubber was pulled. These experiments show an improvement in the sensitivity of the MCF rubber in the extended state.

Closed-loop adaptive optic comparison between a Shack-Hartmann and a distorted grating wavefront sensor

NASA Astrophysics Data System (ADS)

Harrison, Paul; Erry, Gavin R. G.; Otten, Leonard J.; Cuevas, Desirae M.; Weaver, Lawrence D.

2004-11-01

Earlier research reported a comparison of the wavefronts recorded simultaneously by a Shack-Hartmann and a Distorted Grating Wavefront Sensor (DGWFS). In this paper we present the results of a continuation of this earlier work where we have now closed an adaptive optics loop under simulated propagation conditions using the Advanced Concept Laboratory (ACL) at Lincoln Laboratory. For these measurements only one wavefront sensor controlled the deformable mirror at a time. To make direct comparisons between the sensors we took advantage of the ACL's ability to exactly replicate a time varying propagation simulation. Time varying and static comparisons of the two sensors controlling the ACL adaptive system under conditions that ranged from a benign path, D/r0 = 2, to a propagation condition with significant scintillation, D/r0 =9, will be shown using the corrected far field spot as a measure of performance. The paper includes a description of the DGWFS used for these tests and describes the procedure used to align and calibrate the sensor.

Closed-loop adaptive optic comparison between a Shack-Hartmann and a distorted-grating wavefront sensor

NASA Astrophysics Data System (ADS)

Harrison, Paul; Erry, Gavin R. G.; Otten, Leonard J., III; Cuevas, D. M.; Weaver, Lawrence D.

2004-02-01

Earlier research reported a comparison of the wavefronts recorded simultaneously by a Shack-Hartmann and a Distorted Grating Wavefront Sensor (DGWFS). In this paper we present the results of a continuation of this earlier work where we have now closed an adaptive optics loop under simulated propagation conditions using the Advanced Concept Laboratory (ACL) at Lincoln Laboratory. For these measurements only one wavefront sensor controlled the deformable mirror at a time. To make direct comparisons between the sensors we took advantage of the ACL"s ability to exactly replicate a time varying propagation simulation. Time varying and static comparisons of the two sensors controlling the ACL adaptive system under conditions that ranged from a benign path, D/r0 = 2, to a propagation condition with significant scintillation, D/r0 =9, will be shown using the corrected far field spot as a measure of performance. The paper includes a description of the DGWFS used for these tests and describes the procedure used to align and calibrate the sensor.

Evaluation of Candidate Millimeter Wave Sensors for Synthetic Vision

NASA Technical Reports Server (NTRS)

Alexander, Neal T.; Hudson, Brian H.; Echard, Jim D.

1994-01-01

The goal of the Synthetic Vision Technology Demonstration Program was to demonstrate and document the capabilities of current technologies to achieve safe aircraft landing, take off, and ground operation in very low visibility conditions. Two of the major thrusts of the program were (1) sensor evaluation in measured weather conditions on a tower overlooking an unused airfield and (2) flight testing of sensor and pilot performance via a prototype system. The presentation first briefly addresses the overall technology thrusts and goals of the program and provides a summary of MMW sensor tower-test and flight-test data collection efforts. Data analysis and calibration procedures for both the tower tests and flight tests are presented. The remainder of the presentation addresses the MMW sensor flight-test evaluation results, including the processing approach for determination of various performance metrics (e.g., contrast, sharpness, and variability). The variation of the very important contrast metric in adverse weather conditions is described. Design trade-off considerations for Synthetic Vision MMW sensors are presented.

The Study of Cross-layer Optimization for Wireless Rechargeable Sensor Networks Implemented in Coal Mines

PubMed Central

Ding, Xu; Shi, Lei; Han, Jianghong; Lu, Jingting

2016-01-01

Wireless sensor networks deployed in coal mines could help companies provide workers working in coal mines with more qualified working conditions. With the underground information collected by sensor nodes at hand, the underground working conditions could be evaluated more precisely. However, sensor nodes may tend to malfunction due to their limited energy supply. In this paper, we study the cross-layer optimization problem for wireless rechargeable sensor networks implemented in coal mines, of which the energy could be replenished through the newly-brewed wireless energy transfer technique. The main results of this article are two-fold: firstly, we obtain the optimal relay nodes’ placement according to the minimum overall energy consumption criterion through the Lagrange dual problem and KKT conditions; secondly, the optimal strategies for recharging locomotives and wireless sensor networks are acquired by solving a cross-layer optimization problem. The cyclic nature of these strategies is also manifested through simulations in this paper. PMID:26828500

The Study of Cross-layer Optimization for Wireless Rechargeable Sensor Networks Implemented in Coal Mines.

PubMed

Ding, Xu; Shi, Lei; Han, Jianghong; Lu, Jingting

2016-01-28

Wireless sensor networks deployed in coal mines could help companies provide workers working in coal mines with more qualified working conditions. With the underground information collected by sensor nodes at hand, the underground working conditions could be evaluated more precisely. However, sensor nodes may tend to malfunction due to their limited energy supply. In this paper, we study the cross-layer optimization problem for wireless rechargeable sensor networks implemented in coal mines, of which the energy could be replenished through the newly-brewed wireless energy transfer technique. The main results of this article are two-fold: firstly, we obtain the optimal relay nodes' placement according to the minimum overall energy consumption criterion through the Lagrange dual problem and KKT conditions; secondly, the optimal strategies for recharging locomotives and wireless sensor networks are acquired by solving a cross-layer optimization problem. The cyclic nature of these strategies is also manifested through simulations in this paper.

Digitally Programmable Analogue Circuits for Sensor Conditioning Systems

PubMed Central

Zatorre, Guillermo; Medrano, Nicolás; Sanz, María Teresa; Aldea, Concepción; Calvo, Belén; Celma, Santiago

2009-01-01

This work presents two current-mode integrated circuits designed for sensor signal preprocessing in embedded systems. The proposed circuits have been designed to provide good signal transfer and fulfill their function, while minimizing the load effects due to building complex conditioning architectures. The processing architecture based on the proposed building blocks can be reconfigured through digital programmability. Thus, sensor useful range can be expanded, changes in the sensor operation can be compensated for and furthermore, undesirable effects such as device mismatching and undesired physical magnitudes sensor sensibilities are reduced. The circuits were integrated using a 0.35 μm standard CMOS process. Experimental measurements, load effects and a study of two different tuning strategies are presented. From these results, system performance is tested in an application which entails extending the linear range of a magneto-resistive sensor. Circuit area, average power consumption and programmability features allow these circuits to be included in embedded sensing systems as a part of the analogue conditioning components. PMID:22412331

Inflight and Preflight Detection of Pitot Tube Anomalies

NASA Technical Reports Server (NTRS)

Mitchell, Darrell W.

2014-01-01

The health and integrity of aircraft sensors play a critical role in aviation safety. Inaccurate or false readings from these sensors can lead to improper decision making, resulting in serious and sometimes fatal consequences. This project demonstrated the feasibility of using advanced data analysis techniques to identify anomalies in Pitot tubes resulting from blockage such as icing, moisture, or foreign objects. The core technology used in this project is referred to as noise analysis because it relates sensors' response time to the dynamic component (noise) found in the signal of these same sensors. This analysis technique has used existing electrical signals of Pitot tube sensors that result from measured processes during inflight conditions and/or induced signals in preflight conditions to detect anomalies in the sensor readings. Analysis and Measurement Services Corporation (AMS Corp.) has routinely used this technology to determine the health of pressure transmitters in nuclear power plants. The application of this technology for the detection of aircraft anomalies is innovative. Instead of determining the health of process monitoring at a steady-state condition, this technology will be used to quickly inform the pilot when an air-speed indication becomes faulty under any flight condition as well as during preflight preparation.

Wireless sensor network for monitoring soil moisture and weather conditions

USDA-ARS?s Scientific Manuscript database

A wireless sensor network (WSN) was developed and deployed in three fields to monitor soil water status and collect weather data for irrigation scheduling. The WSN consists of soil-water sensors, weather sensors, wireless data loggers, and a wireless modem. Soil-water sensors were installed at three...

The digital compensation technology system for automotive pressure sensor

NASA Astrophysics Data System (ADS)

Guo, Bin; Li, Quanling; Lu, Yi; Luo, Zai

2011-05-01

Piezoresistive pressure sensor be made of semiconductor silicon based on Piezoresistive phenomenon, has many characteristics. But since the temperature effect of semiconductor, the performance of silicon sensor is also changed by temperature, and the pressure sensor without temperature drift can not be produced at present. This paper briefly describe the principles of sensors, the function of pressure sensor and the various types of compensation method, design the detailed digital compensation program for automotive pressure sensor. Simulation-Digital mixed signal conditioning is used in this dissertation, adopt signal conditioning chip MAX1452. AVR singlechip ATMEGA128 and other apparatus; fulfill the design of digital pressure sensor hardware circuit and singlechip hardware circuit; simultaneously design the singlechip software; Digital pressure sensor hardware circuit is used to implementing the correction and compensation of sensor; singlechip hardware circuit is used to implementing to controll the correction and compensation of pressure sensor; singlechip software is used to implementing to fulfill compensation arithmetic. In the end, it implement to measure the output of sensor, and contrast to the data of non-compensation, the outcome indicates that the compensation precision of compensated sensor output is obviously better than non-compensation sensor, not only improving the compensation precision but also increasing the stabilization of pressure sensor.

Reconfigurable Sensor Monitoring System

NASA Technical Reports Server (NTRS)

Alhorn, Dean C. (Inventor); Dutton, Kenneth R. (Inventor); Howard, David E. (Inventor); Smith, Dennis A. (Inventor)

2017-01-01

A reconfigurable sensor monitoring system includes software tunable filters, each of which is programmable to condition one type of analog signal. A processor coupled to the software tunable filters receives each type of analog signal so-conditioned.

In-Vitro Performance of the Enlite Sensor in Various Glucose Concentrations during Hypobaric and Hyperbaric Conditions

PubMed Central

Adolfsson, Peter; Örnhagen, Hans; Eriksson, Bengt M.; Gautham, Raghavendhar; Jendle, Johan

2012-01-01

Background There is a need for reliable methods of glucose measurement in different environmental conditions. The objective of this in vitro study was to evaluate the performance of the Enlite® Sensor when connected to either the iPro™ Continuous Glucose Monitor recording device or the Guardian® REAL-Time transmitting device, in hypobaric and hyperbaric conditions. Methods Sixteen sensors connected to eight iPro devices and eight Guardian REAL-Time devices were immersed in three beakers containing separate glucose concentrations: 52, 88, and 207 mg/dl (2.9, 4.9, and 11.3 mmol/liter). Two different pressure tests were conducted: a hypobaric test, corresponding to maximum 18000 ft/5500 m height, and a hyperbaric test, corresponding to maximum 100 ft/30 m depth. The linearity of the sensor signals in the different conditions was evaluated. Results The sensors worked continuously, and the sensor signals were collected without interruption at all pressures tested. When comparing the input signals for glucose (ISIGs) and the different glucose concentrations during altered pressure, linearity (R2) of 0.98 was found. During the hypobaric test, significant differences (p < .005) were seen when comparing the ISIGs during varying pressure at two of the glucose concentrations (52 and 207 mg/dl), whereas no difference was seen at the 88 mg/dl glucose concentration. During the hyperbaric test, no differences were found. Conclusions The Enlite Sensors connected to either the iPro or the Guardian REAL-Time device provided values continuously. In hyperbaric conditions, no significant differences were seen during changes in ambient pressure; however, during hypobaric conditions, the ISIG was significantly different in the low and high glucose concentrations. PMID:23294783

In-vitro performance of the Enlite Sensor in various glucose concentrations during hypobaric and hyperbaric conditions.

PubMed

Adolfsson, Peter; Ornhagen, Hans; Eriksson, Bengt M; Gautham, Raghavendhar; Jendle, Johan

2012-11-01

There is a need for reliable methods of glucose measurement in different environmental conditions. The objective of this in vitro study was to evaluate the performance of the Enlite® Sensor when connected to either the iPro™ Continuous Glucose Monitor recording device or the Guardian® REAL-Time transmitting device, in hypobaric and hyperbaric conditions. Sixteen sensors connected to eight iPro devices and eight Guardian REAL-Time devices were immersed in three beakers containing separate glucose concentrations: 52, 88, and 207 mg/dl (2.9, 4.9, and 11.3 mmol/liter). Two different pressure tests were conducted: a hypobaric test, corresponding to maximum 18000 ft/5500 m height, and a hyperbaric test, corresponding to maximum 100 ft/30 m depth. The linearity of the sensor signals in the different conditions was evaluated. The sensors worked continuously, and the sensor signals were collected without interruption at all pressures tested. When comparing the input signals for glucose (ISIGs) and the different glucose concentrations during altered pressure, linearity (R(2)) of 0.98 was found. During the hypobaric test, significant differences (p < .005) were seen when comparing the ISIGs during varying pressure at two of the glucose concentrations (52 and 207 mg/dl), whereas no difference was seen at the 88 mg/dl glucose concentration. During the hyperbaric test, no differences were found. The Enlite Sensors connected to either the iPro or the Guardian REAL-Time device provided values continuously. In hyperbaric conditions, no significant differences were seen during changes in ambient pressure; however, during hypobaric conditions, the ISIG was significantly different in the low and high glucose concentrations. © 2012 Diabetes Technology Society.

Understanding and Mapping Water Quality for Lawrence, MA

EPA Pesticide Factsheets

EPA has created new maps of the lower Merrimack River that provide an overview of historic water quality data (E. coli concentrations); flood zones, precipitation, and combined sewer overflows (CSOs).

78 FR 66754 - Center for Scientific Review; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-06

... Drive, Bethesda, MD 20892, (Virtual Meeting). Contact Person: Lynn E Luethke, Ph.D., Scientific Review... Scientific Review Special Emphasis Panel, Social Psychology, Personality and Interpersonal Processes Overflow...

DebuggingDemo v. 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaines, Sherry

Intentionally simple buggy code created for use in a debugging demonstration as part of recruiting tech talks. Code exemplifies a buffer overflow, leading to return address corruption. Code also demonstrates unused return value.

Distributions of pharmaceuticals in an urban estuary during both dry- and wet-weather conditions

USGS Publications Warehouse

Benotti, M.J.; Brownawell, Bruce J.

2007-01-01

Pharmaceuticals and selected major human metabolites are ubiquitous in Jamaica Bay, a wastewater-impacted estuary at concentrations in the low ng/L to low ??g/L range. Concentrations throughout the bay are often consistent with conservative behavior during dry-weather conditions, as evidenced by nearly linear concentration-salinity relationships. Deviation from conservative behavior is noted for some pharmaceuticals and attributed to microbial degradation. Caffeine, cotinine, nicotine, and paraxanthine were detected with the greatest analytical signal, although evidence is presented for in situ removal, especially for nicotine and caffeine. There is little evidence for significant removal of carbamazepine and sulfamethoxazole, suggesting they are more conservative and useful wastewater tracers. Immediately following heavy precipitation, which induced a combined sewer overflow (CSO) event, the concentrations of all compounds but acetaminophen and nicotine decreased or disappeared. This observation is consistent with a simple model illustrating the effect of precipitation has on pharmaceutical concentration in the wastewater stream, given the balance between dilution from rain and the bypass of treatment. ?? 2007 American Chemical Society.

Establishing Approaches to Modeling the Ares I-X and Ares I Roll Control System with Free-stream Interaction

NASA Technical Reports Server (NTRS)

Pao, S. Paul; Deere, Karen A.; Abdol-Hamid, Khales S.

2011-01-01

Approaches were established for modeling the roll control system and analyzing the jet interactions of the activated roll control system on Ares-type configurations using the USM3D Navier-Stokes solver. Components of the modeling approach for the roll control system include a choice of turbulence models, basis for computing a dynamic equivalence of the real gas rocket exhaust flow in terms of an ideal gas, and techniques to evaluate roll control system performance for wind tunnel and flight conditions. A simplified Ares I-X configuration was used during the development phase of the roll control system modeling approach. A limited set of Navier-Stokes solutions was obtained for the purposes of this investigation and highlights of the results are included in this paper. The USM3D solutions were compared to equivalent solutions at select flow conditions from a real gas Navier- Stokes solver (Loci-CHEM) and a structured overset grid Navier-Stokes solver (OVERFLOW).

Field performance of self-siphon sediment cleansing set for sediment removal in deep CSO chamber.

PubMed

Zhou, Yongchao; Zhang, Yiping; Tang, Ping

2013-01-01

This paper presents a study of the self-siphon sediment cleansing set (SSCS), a system designed to remove sediment from the deep combined sewer overflow (CSO) chamber during dry-weather periods. In order to get a better understanding of the sediment removal effectiveness and operational conditions of the SSCS system, we carried out a full-scale field study and comparison analysis on the sediment depth changes in the deep CSO chambers under the conditions with and without the SSCS. The field investigation results demonstrated that the SSCS drains the dry-weather flow that accumulated for 50-57 min from the sewer channel to the intercepting system in about 10 min. It is estimated that the bed shear stress in the CSO chamber and sewer channel is improved almost 25 times on average. The SSCS acts to remove the near bed solids with high pollution load efficiently. Moreover, it cleans up not only the new sediment layer but also part of the previously accumulated sediment.

Coordinated management of combined sewer overflows by means of environmental decision support systems.

PubMed

Murla, Damian; Gutierrez, Oriol; Martinez, Montse; Suñer, David; Malgrat, Pere; Poch, Manel

2016-04-15

During heavy rainfall, the capacity of sewer systems and wastewater treatment plants may be surcharged producing uncontrolled wastewater discharges and a depletion of the environmental quality. Therefore there is a need of advanced management tools to tackle with these complex problems. In this paper an environmental decision support system (EDSS), based on the integration of mathematical modeling and knowledge-based systems, has been developed for the coordinated management of urban wastewater systems (UWS) to control and minimize uncontrolled wastewater spills. Effectiveness of the EDSS has been tested in a specially designed virtual UWS, including two sewers systems, two WWTP and one river subjected to typical Mediterranean rain conditions. Results show that sewer systems, retention tanks and wastewater treatment plants improve their performance under wet weather conditions and that EDSS can be very effective tools to improve the management and prevent the system from possible uncontrolled wastewater discharges. Copyright © 2016 Elsevier B.V. All rights reserved.

The use of water marks mapping to understand flood overflow events inside karstic cavities: Cueva Fría and Cueva Rosa (Asturias, NW Spain)

NASA Astrophysics Data System (ADS)

González Lemos, Saúl; Stoll, Heather M.

2014-05-01

Several karst systems in Asturias (NW Spain) present evidence of fluvial deposits cemented in speleothems that may provide good chronology of past flood events inside the caves. This flood record is under research in two karstic caves of this region, Cueva Fría and Cueva Rosa, which have in common the presence of a perennial stream inside the cave and a low gradient of the cave passage. Immediately after a flood overflow event, water marks, foam and detritus are visible at different heights on the cave walls and correspond to heights of bottlenecks in overflow drainage through the cave passage. Flood events also deposit sand and gravel on terraces on the cave wall and move large volumes of sand in the cave bed. We have noted that detrital particles (like sand or silt particles) are preserved as inclusions inside the stalagmites and that their abundance inside coeval stalagmites decreases as altitude and distance from the perennial stream increase, supporting its fluvial affinity. However, not all the stalagmites that contain detrital particles are located close to the perennial streams. In this work, we have mapped the water marks preserved in the cave walls to reconstruct water levels associated to flood overflow events of different magnitude. We have found that water mark correlation along the cave passage is very useful to define the hydrological behaviour and flood model of the cave during these extreme events. The water mark mapping and correlation have been also useful to prove that during periods of high rainfall, the movement of the sand-bars inside the cave can cover partially or completely active stalagmites, facilitating the cementation process and trapping abundant detrital material inside the stalagmite carbonate. 14C and U/Th dating of the stalagmites can provide a chronology for the detrital rich layers, so that the abundance of fluvial material in the stalagmites can reveal periods of enhanced vs. reduced flooding in the cave over the past several thousand years (Holocene).

Biased thermohaline exchanges with the Arctic across the Iceland-Faroe Ridge in ocean climate models

NASA Astrophysics Data System (ADS)

Olsen, S. M.; Hansen, B.; Østerhus, S.; Quadfasel, D.; Valdimarsson, H.

2016-04-01

The northern limb of the Atlantic thermohaline circulation and its transport of heat and salt towards the Arctic strongly modulate the climate of the Northern Hemisphere. The presence of warm surface waters prevents ice formation in parts of the Arctic Mediterranean, and ocean heat is directly available for sea-ice melt, while salt transport may be critical for the stability of the exchanges. Through these mechanisms, ocean heat and salt transports play a disproportionally strong role in the climate system, and realistic simulation is a requisite for reliable climate projections. Across the Greenland-Scotland Ridge (GSR) this occurs in three well-defined branches where anomalies in the warm and saline Atlantic inflow across the shallow Iceland-Faroe Ridge (IFR) have been shown to be particularly difficult to simulate in global ocean models. This branch (IF-inflow) carries about 40 % of the total ocean heat transport into the Arctic Mediterranean and is well constrained by observation during the last 2 decades but associated with significant inter-annual fluctuations. The inconsistency between model results and observational data is here explained by the inability of coarse-resolution models to simulate the overflow across the IFR (IF-overflow), which feeds back onto the simulated IF-inflow. In effect, this is reduced in the model to reflect only the net exchange across the IFR. Observational evidence is presented for a substantial and persistent IF-overflow and mechanisms that qualitatively control its intensity. Through this, we explain the main discrepancies between observed and simulated exchange. Our findings rebuild confidence in modelled net exchange across the IFR, but reveal that compensation of model deficiencies here through other exchange branches is not effective. This implies that simulated ocean heat transport to the Arctic is biased low by more than 10 % and associated with a reduced level of variability, while the quality of the simulated salt transport becomes critically dependent on the link between IF-inflow and IF-overflow. These features likely affect sensitivity and stability of climate models to climate change and limit the predictive skill.

Modelling sewer sediment deposition, erosion, and transport processes to predict acute influent and reduce combined sewer overflows and CO(2) emissions.

PubMed

Mouri, Goro; Oki, Taikan

2010-01-01

Understanding of solids deposition, erosion, and transport processes in sewer systems has improved considerably in the past decade. This has provided guidance for controlling sewer solids and associated acute pollutants to protect the environment and improve the operation of wastewater systems. Although measures to decrease combined sewer overflow (CSO) events have reduced the amount of discharged pollution, overflows continue to occur during rainy weather in combined sewer systems. The solution lies in the amount of water allotted to various processes in an effluent treatment system, in impact evaluation of water quality and prediction technology, and in stressing the importance of developing a control technology. Extremely contaminated inflow has been a serious research subject, especially in connection with the influence of rainy weather on nitrogen and organic matter removal efficiency in wastewater treatment plants (WWTP). An intensive investigation of an extremely polluted inflow load to WWTP during rainy weather was conducted in the city of Matsuyama, the region used for the present research on total suspended solid (TSS) concentration. Since the inflow during rainy weather can be as much as 400 times that in dry weather, almost all sewers are unsettled and overflowing when a rain event is more than moderate. Another concern is the energy consumed by wastewater treatment; this problem has become important from the viewpoint of reducing CO(2) emissions and overall costs. Therefore, while establishing a prediction technology for the inflow water quality characteristics of a sewage disposal plant is an important priority, the development of a management/control method for an effluent treatment system that minimises energy consumption and CO(2) emissions due to water disposal is also a pressing research topic with regards to the quality of treated water. The procedure to improve water quality must make use of not only water quality and biotic criteria, but also modelling systems to enable the user to link the effect of changes in urban sewage systems with specific quality, energy consumption, CO(2) emission, and ecological improvements of the receiving water.

Water balance monitoring for two bioretention gardens in Omaha, Nebraska, 2011–14

USGS Publications Warehouse

Strauch, Kellan R.; Rus, David L.; Holm, Kent E.

2016-01-29

Bioretention gardens are used to help mitigate stormwater runoff in urban settings in an attempt to restore the hydrologic response of the developed land to a natural predevelopment response in which more water is infiltrated rather than routed directly to urban drainage networks. To better understand the performance of bioretention gardens in facilitating infiltration of stormwater in eastern Nebraska, the U.S. Geological Survey, in cooperation with the Douglas County Environmental Services and the Nebraska Environmental Trust, assessed the water balance of two bioretention gardens located in Omaha, Nebraska by monitoring the amount of stormwater entering and leaving the gardens. One garden is on the Douglas County Health Center campus, and the other garden is on the property of the Eastern Nebraska Office on Aging.For the Douglas County Health Center, bioretention garden performance was evaluated on the basis of volume reduction by comparing total inflow volume to total outflow volume. The bioretention garden reduced inflow volumes from a minimum of 33 percent to 100 percent (a complete reduction in inflow volume) depending on the size of the event. Although variable, the percent reduction of the inflow volume tended to decrease with increasing total event rainfall. To assess how well the garden reduces stormwater peak inflow rates, peak inflows were plotted against peak outflows measured at the bioretention garden. Only 39 of the 255 events had any overflow, indicating 100 percent peak reduction in the other events. Of those 39 events having overflow, the mean peak reduction was 63 percent.No overflow events were recorded at the bioretention garden at the Eastern Nebraska Office on Aging; therefore, data were not available for an event-based overflow analysis.Monitoring period summary of the water balance at both bio-retention gardens indicates that most of the stormwater in the bioretention gardens is stored in the subsurface.Evapotranspiration was attributed to a small percentage of the outputs on an annual basis (3 percent at Douglas County Health Center site and 5 percent at Eastern Nebraska Office onAging site), which indicates that vegetative water uptake is not a primary factor in the water budget.

79. VIEW OF SPILLWAY THAT AUTOMATICALLY REGULATES HEIGHT OF WATER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

79. VIEW OF SPILLWAY THAT AUTOMATICALLY REGULATES HEIGHT OF WATER IN RESERVOIR, 'BACKWATER OVERFLOW,' Print No. 233, April 1904 - Electron Hydroelectric Project, Along Puyallup River, Electron, Pierce County, WA

Sewage Overflow Community Right-to-Know Act

THOMAS, 111th Congress

Sen. Lautenberg, Frank R. [D-NJ

2009-04-30

Senate - 04/20/2010 Placed on Senate Legislative Calendar under General Orders. Calendar No. 355. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Material condition assessment with eddy current sensors

NASA Technical Reports Server (NTRS)

Goldfine, Neil J. (Inventor); Washabaugh, Andrew P. (Inventor); Sheiretov, Yanko K. (Inventor); Schlicker, Darrell E. (Inventor); Lyons, Robert J. (Inventor); Windoloski, Mark D. (Inventor); Craven, Christopher A. (Inventor); Tsukernik, Vladimir B. (Inventor); Grundy, David C. (Inventor)

2010-01-01

Eddy current sensors and sensor arrays are used for process quality and material condition assessment of conducting materials. In an embodiment, changes in spatially registered high resolution images taken before and after cold work processing reflect the quality of the process, such as intensity and coverage. These images also permit the suppression or removal of local outlier variations. Anisotropy in a material property, such as magnetic permeability or electrical conductivity, can be intentionally introduced and used to assess material condition resulting from an operation, such as a cold work or heat treatment. The anisotropy is determined by sensors that provide directional property measurements. The sensor directionality arises from constructs that use a linear conducting drive segment to impose the magnetic field in a test material. Maintaining the orientation of this drive segment, and associated sense elements, relative to a material edge provides enhanced sensitivity for crack detection at edges.

Laboratory Performance of Five Selected Soil Moisture Sensors Applying Factory and Own Calibration Equations for Two Soil Media of Different Bulk Density and Salinity Levels.

PubMed

Matula, Svatopluk; Báťková, Kamila; Legese, Wossenu Lemma

2016-11-15

Non-destructive soil water content determination is a fundamental component for many agricultural and environmental applications. The accuracy and costs of the sensors define the measurement scheme and the ability to fit the natural heterogeneous conditions. The aim of this study was to evaluate five commercially available and relatively cheap sensors usually grouped with impedance and FDR sensors. ThetaProbe ML2x (impedance) and ECH₂O EC-10, ECH₂O EC-20, ECH₂O EC-5, and ECH₂O TE (all FDR) were tested on silica sand and loess of defined characteristics under controlled laboratory conditions. The calibrations were carried out in nine consecutive soil water contents from dry to saturated conditions (pure water and saline water). The gravimetric method was used as a reference method for the statistical evaluation (ANOVA with significance level 0.05). Generally, the results showed that our own calibrations led to more accurate soil moisture estimates. Variance component analysis arranged the factors contributing to the total variation as follows: calibration (contributed 42%), sensor type (contributed 29%), material (contributed 18%), and dry bulk density (contributed 11%). All the tested sensors performed very well within the whole range of water content, especially the sensors ECH₂O EC-5 and ECH₂O TE, which also performed surprisingly well in saline conditions.

Laboratory Performance of Five Selected Soil Moisture Sensors Applying Factory and Own Calibration Equations for Two Soil Media of Different Bulk Density and Salinity Levels

PubMed Central

Matula, Svatopluk; Báťková, Kamila; Legese, Wossenu Lemma

2016-01-01

Non-destructive soil water content determination is a fundamental component for many agricultural and environmental applications. The accuracy and costs of the sensors define the measurement scheme and the ability to fit the natural heterogeneous conditions. The aim of this study was to evaluate five commercially available and relatively cheap sensors usually grouped with impedance and FDR sensors. ThetaProbe ML2x (impedance) and ECH2O EC-10, ECH2O EC-20, ECH2O EC-5, and ECH2O TE (all FDR) were tested on silica sand and loess of defined characteristics under controlled laboratory conditions. The calibrations were carried out in nine consecutive soil water contents from dry to saturated conditions (pure water and saline water). The gravimetric method was used as a reference method for the statistical evaluation (ANOVA with significance level 0.05). Generally, the results showed that our own calibrations led to more accurate soil moisture estimates. Variance component analysis arranged the factors contributing to the total variation as follows: calibration (contributed 42%), sensor type (contributed 29%), material (contributed 18%), and dry bulk density (contributed 11%). All the tested sensors performed very well within the whole range of water content, especially the sensors ECH2O EC-5 and ECH2O TE, which also performed surprisingly well in saline conditions. PMID:27854263

Enabling Smart Air Conditioning by Sensor Development: A Review

PubMed Central

Cheng, Chin-Chi; Lee, Dasheng

2016-01-01

The study investigates the development of sensors, in particular the use of thermo-fluidic sensors and occupancy detectors, to achieve smart operation of air conditioning systems. Smart operation refers to the operation of air conditioners by the reinforcement of interaction to achieve both thermal comfort and energy efficiency. Sensors related to thermal comfort include those of temperature, humidity, and pressure and wind velocity anemometers. Improvements in their performance in the past years have been studied by a literature survey. Traditional occupancy detection using passive infra-red (PIR) sensors and novel methodologies using smartphones and wearable sensors are both discussed. Referring to the case studies summarized in this study, air conditioning energy savings are evaluated quantitatively. Results show that energy savings of air conditioners before 2000 was 11%, and 30% after 2000 by the integration of thermo-fluidic sensors and occupancy detectors. By utilizing wearable sensing to detect the human motions, metabolic rates and related information, the energy savings can reach up to 46.3% and keep the minimum change of predicted mean vote (∆PMV→0), which means there is no compromise in thermal comfort. This enables smart air conditioning to compensate for the large variations from person to person in terms of physiological and psychological satisfaction, and find an optimal temperature for everyone in a given space. However, this tendency should be evidenced by more experimental results in the future. PMID:27916906

Atmospheric radiance interpolation for the modeling of hyperspectral data

NASA Astrophysics Data System (ADS)

Fuehrer, Perry; Healey, Glenn; Rauch, Brian; Slater, David; Ratkowski, Anthony

2008-04-01

The calibration of data from hyperspectral sensors to spectral radiance enables the use of physical models to predict measured spectra. Since environmental conditions are often unknown, material detection algorithms have emerged that utilize predicted spectra over ranges of environmental conditions. The predicted spectra are typically generated by a radiative transfer (RT) code such as MODTRAN TM. Such techniques require the specification of a set of environmental conditions. This is particularly challenging in the LWIR for which temperature and atmospheric constituent profiles are required as inputs for the RT codes. We have developed an automated method for generating environmental conditions to obtain a desired sampling of spectra in the sensor radiance domain. Our method provides a way of eliminating the usual problems encountered, because sensor radiance spectra depend nonlinearly on the environmental parameters, when model conditions are specified by a uniform sampling of environmental parameters. It uses an initial set of radiance vectors concatenated over a set of conditions to define the mapping from environmental conditions to sensor spectral radiance. This approach enables a given number of model conditions to span the space of desired radiance spectra and improves both the accuracy and efficiency of detection algorithms that rely upon use of predicted spectra.

Rack protection monitor

DOEpatents

Orr, Stanley G.

2000-01-01

A hardwired, fail-safe rack protection monitor utilizes electromechanical relays to respond to the detection by condition sensors of abnormal or alarm conditions (such as smoke, temperature, wind or water) that might adversely affect or damage equipment being protected. When the monitor is reset, the monitor is in a detection mode with first and second alarm relay coils energized. If one of the condition sensors detects an abnormal condition, the first alarm relay coil will be de-energized, but the second alarm relay coil will remain energized. This results in both a visual and an audible alarm being activated. If a second alarm condition is detected by another one of the condition sensors while the first condition sensor is still detecting the first alarm condition, both the first alarm relay coil and the second alarm relay coil will be de-energized. With both the first and second alarm relay coils de-energized, both a visual and an audible alarm will be activated. In addition, power to the protected equipment will be terminated and an alarm signal will be transmitted to an alarm central control. The monitor can be housed in a separate enclosure so as to provide an interface between a power supply for the protected equipment and the protected equipment.

Unraveling fabrication and calibration of wearable gas monitor for use under free-living conditions.

PubMed

Yue Deng; Cheng Chen; Tsow, Francis; Xiaojun Xian; Forzani, Erica

2016-08-01

Volatile organic compounds (VOC) are organic chemicals that have high vapor pressure at regular conditions. Some VOC could be dangerous to human health, therefore it is important to determine real-time indoor and outdoor personal exposures to VOC. To achieve this goal, our group has developed a wearable gas monitor with a complete sensor fabrication and calibration protocol for free-living conditions. Correction factors for calibrating the sensors, including sensitivity, aging effect, and temperature effect are implemented into a Quick Response Code (QR code), so that the pre-calibrated quartz tuning fork (QTF) sensor can be used with the wearable monitor under free-living conditions.

A suite of optical fibre sensors for structural condition monitoring

NASA Astrophysics Data System (ADS)

Sun, T.; Grattan, K. T. V.; Carlton, J.

2015-05-01

This paper is to review the research activities at City University London in the development of a range of fibre Bragg grating (FBG)-based sensors, including strain, temperature, relative humidity, vibration and acoustic sensors, with an aim to meet the increasing demands from industry for structural condition monitoring. As a result, arrays of optical fibre sensors have been instrumented into various types of structures, including concrete, limestone, marine propellers, pantograph and electrical motors, allowing for both static and dynamic monitoring and thus enhanced structural reliability and integrity.

Evaluation of Flexible Force Sensors for Pressure Monitoring in Treatment of Chronic Venous Disorders.

PubMed

Parmar, Suresh; Khodasevych, Iryna; Troynikov, Olga

2017-08-21

The recent use of graduated compression therapy for treatment of chronic venous disorders such as leg ulcers and oedema has led to considerable research interest in flexible and low-cost force sensors. Properly applied low pressure during compression therapy can substantially improve the treatment of chronic venous disorders. However, achievement of the recommended low pressure levels and its accurate determination in real-life conditions is still a challenge. Several thin and flexible force sensors, which can also function as pressure sensors, are commercially available, but their real-life sensing performance has not been evaluated. Moreover, no researchers have reported information on sensor performance during static and dynamic loading within the realistic test conditions required for compression therapy. This research investigated the sensing performance of five low-cost commercial pressure sensors on a human-leg-like test apparatus and presents quantitative results on the accuracy and drift behaviour of these sensors in both static and dynamic conditions required for compression therapy. Extensive experimental work on this new human-leg-like test setup demonstrated its utility for evaluating the sensors. Results showed variation in static and dynamic sensing performance, including accuracy and drift characteristics. Only one commercially available pressure sensor was found to reliably deliver accuracy of 95% and above for all three test pressure points of 30, 50 and 70 mmHg.

Evaluation of Flexible Force Sensors for Pressure Monitoring in Treatment of Chronic Venous Disorders

PubMed Central

Parmar, Suresh; Khodasevych, Iryna; Troynikov, Olga

2017-01-01

The recent use of graduated compression therapy for treatment of chronic venous disorders such as leg ulcers and oedema has led to considerable research interest in flexible and low-cost force sensors. Properly applied low pressure during compression therapy can substantially improve the treatment of chronic venous disorders. However, achievement of the recommended low pressure levels and its accurate determination in real-life conditions is still a challenge. Several thin and flexible force sensors, which can also function as pressure sensors, are commercially available, but their real-life sensing performance has not been evaluated. Moreover, no researchers have reported information on sensor performance during static and dynamic loading within the realistic test conditions required for compression therapy. This research investigated the sensing performance of five low-cost commercial pressure sensors on a human-leg-like test apparatus and presents quantitative results on the accuracy and drift behaviour of these sensors in both static and dynamic conditions required for compression therapy. Extensive experimental work on this new human-leg-like test setup demonstrated its utility for evaluating the sensors. Results showed variation in static and dynamic sensing performance, including accuracy and drift characteristics. Only one commercially available pressure sensor was found to reliably deliver accuracy of 95% and above for all three test pressure points of 30, 50 and 70 mmHg. PMID:28825672

Improving the satellite communication efficiency of the accumulative acknowledgement strategies

NASA Astrophysics Data System (ADS)

Duarte, Otto Carlos M. B.; de Lima, Heliomar Medeiros

The performances of two finite buffer error recovery strategies are analyzed. In both strategies the retransmission request decision between selective repeat and continuous retransmission is based on an imminent buffer overflow condition. These are accumulative acknowledgment schemes, but in the second strategy the selective-repeat control frame is uniquely an individual negative acknowledgment. The two strategies take advantage of the availability of a greater buffer capacity, making the most of the selective repeat, postponing the sending of a continuous retransmission request. Numerical results show a better performance very close to the ideal, but it does not integrally conform to the high-level data link control (HDLC) procedures. It is shown that these strategies are well suited for high-speed data transfer in the high-error-rate satellite environment.

End-to-End Flow Control for Visual-Haptic Communication under Bandwidth Change

NASA Astrophysics Data System (ADS)

Yashiro, Daisuke; Tian, Dapeng; Yakoh, Takahiro

This paper proposes an end-to-end flow controller for visual-haptic communication. A visual-haptic communication system transmits non-real-time packets, which contain large-size visual data, and real-time packets, which contain small-size haptic data. When the transmission rate of visual data exceeds the communication bandwidth, the visual-haptic communication system becomes unstable owing to buffer overflow. To solve this problem, an end-to-end flow controller is proposed. This controller determines the optimal transmission rate of visual data on the basis of the traffic conditions, which are estimated by the packets for haptic communication. Experimental results confirm that in the proposed method, a short packet-sending interval and a short delay are achieved under bandwidth change, and thus, high-precision visual-haptic communication is realized.

Petri net modelling of buffers in automated manufacturing systems.

PubMed

Zhou, M; Dicesare, F

1996-01-01

This paper presents Petri net models of buffers and a methodology by which buffers can be included in a system without introducing deadlocks or overflows. The context is automated manufacturing. The buffers and models are classified as random order or order preserved (first-in-first-out or last-in-first-out), single-input-single-output or multiple-input-multiple-output, part type and/or space distinguishable or indistinguishable, and bounded or safe. Theoretical results for the development of Petri net models which include buffer modules are developed. This theory provides the conditions under which the system properties of boundedness, liveness, and reversibility are preserved. The results are illustrated through two manufacturing system examples: a multiple machine and multiple buffer production line and an automatic storage and retrieval system in the context of flexible manufacturing.

Framing 100-year overflowing and overtopping marine submersion hazard resulting from the propagation of 100-year joint hydrodynamic conditions

NASA Astrophysics Data System (ADS)

Nicolae Lerma, A.; Bulteau, T.; Elineau, S.; Paris, F.; Pedreros, R.

2016-12-01

Marine submersion is an increasing concern for coastal cities as urban development reinforces their vulnerabilities while climate change is likely to foster the frequency and magnitude of submersions. Characterising the coastal flooding hazard is therefore of paramount importance to ensure the security of people living in such places and for coastal planning. A hazard is commonly defined as an adverse phenomenon, often represented by a magnitude of a variable of interest (e.g. flooded area), hereafter called response variable, associated with a probability of exceedance or, alternatively, a return period. Characterising the coastal flooding hazard consists in finding the correspondence between the magnitude and the return period. The difficulty lies in the fact that the assessment is usually performed using physical numerical models taking as inputs scenarios composed by multiple forcing conditions that are most of the time interdependent. Indeed, a time series of the response variable is usually not available so we have to deal instead with time series of forcing variables (e.g. water level, waves). Thus, the problem is twofold: on the one hand, the definition of scenarios is a multivariate matter; on the other hand, it is tricky and approximate to associate the resulting response, being the output of the physical numerical model, to the return period defined for the scenarios. In this study, we illustrate the problem on the district of Leucate, located in the French Mediterranean coast. A multivariate extreme value analysis of waves and water levels is performed offshore using a conditional extreme model, then two different methods are used to define and select 100-year scenarios of forcing variables: one based on joint exceedance probability contours, a method classically used in coastal risks studies, the other based on environmental contours, which are commonly used in the field of structure design engineering. We show that these two methods enable one to frame the true 100-year response variable. The selected scenarios are propagated to the shore through a high resolution flood modelling coupling overflowing and overtopping processes. Results in terms of inundated areas and inland water volumes are finally compared for the two methods, giving upper and lower bounds for the true response variables.

Parameter monitoring compensation system and method

DOEpatents

Barkman, William E.; Babelay, Edwin F.; DeMint, Paul D.; Hebble, Thomas L.; Igou, Richard E.; Williams, Richard R.; Klages, Edward J.; Rasnick, William H.

1995-01-01

A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along preprogrammed path during a machining operation utilizes sensors for gathering information at a preselected stage of a machining operation relating to an actual condition. The controller compares the actual condition to a condition which the program presumes to exist at the preselected stage and alters the program in accordance with detected variations between the actual condition and the assumed condition. Such conditions may be related to process parameters, such as a position, dimension or shape of the cutting tool or workpiece or an environmental temperature associated with the machining operation, and such sensors may be a contact or a non-contact type of sensor or a temperature transducer.

Tele-auscultation support system with mixed reality navigation.

PubMed

Hori, Kenta; Uchida, Yusuke; Kan, Tsukasa; Minami, Maya; Naito, Chisako; Kuroda, Tomohiro; Takahashi, Hideya; Ando, Masahiko; Kawamura, Takashi; Kume, Naoto; Okamoto, Kazuya; Takemura, Tadamasa; Yoshihara, Hiroyuki

2013-01-01

The aim of this research is to develop an information support system for tele-auscultation. In auscultation, a doctor requires to understand condition of applying a stethoscope, in addition to auscultatory sounds. The proposed system includes intuitive navigation system of stethoscope operation, in addition to conventional audio streaming system of auscultatory sounds and conventional video conferencing system for telecommunication. Mixed reality technology is applied for intuitive navigation of the stethoscope. Information, such as position, contact condition and breath, is overlaid on a view of the patient's chest. The contact condition of the stethoscope is measured by e-textile contact sensors. The breath is measured by a band type breath sensor. In a simulated tele-auscultation experiment, the stethoscope with the contact sensors and the breath sensor were evaluated. The results show that the presentation of the contact condition was not understandable enough for navigating the stethoscope handling. The time series of the breath phases was usable for the remote doctor to understand the breath condition of the patient.

GET REAL!

EPA Science Inventory

Combined sewer overflow (CSO) is a significant source of pollution in receiving waters. However, implementing a real-time control scheme operates automatic regulators more efficiently to maximize a collection system's storage, treatment, and transport capacities, reducing the vol...

Moving towards Total Water Management

EPA Science Inventory

The presentation will discuss the following topics: Stormwater Best Management Practice (BMP) Placement (SUSTAIN); Sanitary Sewer Overflow Toolbox (SSOAP); BMP and Low Impact Development (LID) Performance; Green/Grey Infrastructure for Stormwater; Combined Sewers and Reuse; Infra...

Time-Spectral Rotorcraft Simulations on Overset Grids

NASA Technical Reports Server (NTRS)

Leffell, Joshua I.; Murman, Scott M.; Pulliam, Thomas H.

2014-01-01

The Time-Spectral method is derived as a Fourier collocation scheme and applied to NASA's overset Reynolds-averaged Navier-Stokes (RANS) solver OVERFLOW. The paper outlines the Time-Spectral OVERFLOWimplementation. Successful low-speed laminar plunging NACA 0012 airfoil simulations demonstrate the capability of the Time-Spectral method to resolve the highly-vortical wakes typical of more expensive three-dimensional rotorcraft configurations. Dealiasing, in the form of spectral vanishing viscosity (SVV), facilitates the convergence of Time-Spectral calculations of high-frequency flows. Finally, simulations of the isolated V-22 Osprey tiltrotor for both hover and forward (edgewise) flight validate the three-dimensional Time-Spectral OVERFLOW implementation. The Time-Spectral hover simulation matches the time-accurate calculation using a single harmonic. Significantly more temporal modes and SVV are required to accurately compute the forward flight case because of its more active, high-frequency wake.

Addition of Improved Shock-Capturing Schemes to OVERFLOW 2.1

NASA Technical Reports Server (NTRS)

Burning, Pieter G.; Nichols, Robert H.; Tramel, Robert W.

2009-01-01

Existing approximate Riemann solvers do not perform well when the grid is not aligned with strong shocks in the flow field. Three new approximate Riemann algorithms are investigated to improve solution accuracy and stability in the vicinity of strong shocks. The new algorithms are compared to the existing upwind algorithms in OVERFLOW 2.1. The new algorithms use a multidimensional pressure gradient based switch to transition to a more numerically dissipative algorithm in the vicinity of strong shocks. One new algorithm also attempts to artificially thicken captured shocks in order to alleviate the errors in the solution introduced by "stair-stepping" of the shock resulting from the approximate Riemann solver. This algorithm performed well for all the example cases and produced results that were almost insensitive to the alignment of the grid and the shock.

Combined sewage overflows (CSO) are major urban breeding sites for Culex quinquefasciatus in Atlanta, Georgia.

PubMed

Calhoun, Lisa M; Avery, Melissa; Jones, Leeann; Gunarto, Karina; King, Raymond; Roberts, Jacquelin; Burkot, Thomas R

2007-09-01

A longitudinal study of mosquito ecology in Tanyard Creek, an urban stream in Atlanta, GA, that receives combined storm and waste water effluent from the Atlanta combined sewage overflow system, was undertaken in 2006. Culex quinquefasciatus was the dominant species found, but Culex restuans was also abundant during the spring with limited numbers of Culex nigripalpis and Anopheles punctipennis also collected. Significant differences in mosquito densities were found with greater densities associated with side pools of water and stagnant water. Mosquito numbers are regulated largely by flooding of the stream by effluent discharges exceeding 15 kgal/min. These floods are associated with significant immediate reductions, but not complete elimination, of mosquitoes from Tanyard Creek. Mosquito numbers rebound within 5-10 days after such floods and rapidly reach high densities.

Assessing combined sewer overflows with long lead time for better surface water management.

PubMed

Abdellatif, Mawada; Atherton, William; Alkhaddar, Rafid

2014-01-01

During high-intensity rainfall events, the capacity of combined sewer overflows (CSOs) can exceed resulting in discharge of untreated stormwater and wastewater directly into receiving rivers. These discharges can result in high concentrations of microbial pathogens, biochemical oxygen demand, suspended solids, and other pollutants in the receiving waters. The frequency and severity of the CSO discharge are strongly influenced by climatic factors governing the occurrence of urban stormwater runoff, particularly the amount and intensity of the rainfall. This study attempts to assess the impact of climate change (change in rainfall amount and frequency) on CSO under the high (A1FI) and low (B1) Special Report on Emissions Scenarios of the greenhouse concentration derived from three global circulation models in the north west of England at the end of the twenty-first century.

Evidence for ponding and catastrophic floods in central Valles Marineris, Mars

USGS Publications Warehouse

Harrison, K.P.; Chapman, M.G.

2008-01-01

The Valles Marineris canyon system of Mars is closely related to large flood channels, some of which emerge full born from chaotic terrain in canyon floors. Coprates Chasma, one of the largest Valles Marineris canyons, is connected at its west end to Melas Chasma and on its east end to chaotic terrain-filled Capri and Eos Chasmata. The area from central Melas to Eos Chasmata contains a 1500 km long and about 1 km deep depression in its floor. Despite the large volumes of groundwater that likely discharged from chaotic terrain in this depression, no evidence of related fluvial activity has thus far been reported. We present an analysis of the regional topography which, together with photogeologic interpretation of available imagery, suggests that ponding due to late Hesperian discharge of water possibly produced a lake (mean depth 842 m) spanning parts of the Valles Marineris depression (VMD). Overflow of this lake at its eastern end resulted in delivery of water to downstream chaos regions and outflow channels. Our ponding hypothesis is motivated primarily by the identification of scarp and terrace features which, despite a lateral spread of about 1500 km, have similar elevations. Furthermore, these elevations correspond to the maximum ponding elevation of the region (-3560 m). Simulated ponding in the VMD yields an overflow point at its eastern extremity, in Eos Chasma. The neighborhood of this overflow point contains clear indicators of fluvial erosion in a consistent east-west orientation. ?? 2008 Elsevier Inc.

Integrating gene and protein expression data with genome-scale metabolic networks to infer functional pathways.

PubMed

Pey, Jon; Valgepea, Kaspar; Rubio, Angel; Beasley, John E; Planes, Francisco J

2013-12-08

The study of cellular metabolism in the context of high-throughput -omics data has allowed us to decipher novel mechanisms of importance in biotechnology and health. To continue with this progress, it is essential to efficiently integrate experimental data into metabolic modeling. We present here an in-silico framework to infer relevant metabolic pathways for a particular phenotype under study based on its gene/protein expression data. This framework is based on the Carbon Flux Path (CFP) approach, a mixed-integer linear program that expands classical path finding techniques by considering additional biophysical constraints. In particular, the objective function of the CFP approach is amended to account for gene/protein expression data and influence obtained paths. This approach is termed integrative Carbon Flux Path (iCFP). We show that gene/protein expression data also influences the stoichiometric balancing of CFPs, which provides a more accurate picture of active metabolic pathways. This is illustrated in both a theoretical and real scenario. Finally, we apply this approach to find novel pathways relevant in the regulation of acetate overflow metabolism in Escherichia coli. As a result, several targets which could be relevant for better understanding of the phenomenon leading to impaired acetate overflow are proposed. A novel mathematical framework that determines functional pathways based on gene/protein expression data is presented and validated. We show that our approach is able to provide new insights into complex biological scenarios such as acetate overflow in Escherichia coli.

Identifiability of Additive Actuator and Sensor Faults by State Augmentation

NASA Technical Reports Server (NTRS)

Joshi, Suresh; Gonzalez, Oscar R.; Upchurch, Jason M.

2014-01-01

A class of fault detection and identification (FDI) methods for bias-type actuator and sensor faults is explored in detail from the point of view of fault identifiability. The methods use state augmentation along with banks of Kalman-Bucy filters for fault detection, fault pattern determination, and fault value estimation. A complete characterization of conditions for identifiability of bias-type actuator faults, sensor faults, and simultaneous actuator and sensor faults is presented. It is shown that FDI of simultaneous actuator and sensor faults is not possible using these methods when all sensors have unknown biases. The fault identifiability conditions are demonstrated via numerical examples. The analytical and numerical results indicate that caution must be exercised to ensure fault identifiability for different fault patterns when using such methods.

Broadband, Common-path, Interferometric Wavefront Sensor

NASA Technical Reports Server (NTRS)

Wallace, James Kent (Inventor)

2015-01-01

Hybrid sensors comprising Shack-Hartmann Wavefront Sensor (S-HWFS) and Zernike Wavefront Sensor (Z-WFS) capabilities are presented. The hybrid sensor includes a Z-WFS optically arranged in-line with a S-HWFS such that the combined wavefront sensor operates across a wide dynamic range and noise conditions. The Z-WFS may include the ability to introduce a dynamic phase shift in both transmissive and reflective modes.

Physical context management for a motor vehicle

DOEpatents

Dixon, Kevin R [Albuquerque, NM; Forsythe, James C [Sandia Park, NM; Lippitt, Carl E [Albuquerque, NM; Lippitt, legal representative, Lois Diane

2009-10-27

Computer software for and a method of enhancing safety for an operator of a motor vehicle comprising employing a plurality of sensors of vehicle and operator conditions, matching collective output from the sensors against a plurality of known dangerous conditions, and preventing certain activity of the operator if a known dangerous condition is detected.

High Temperature Dynamic Pressure Measurements Using Silicon Carbide Pressure Sensors

NASA Technical Reports Server (NTRS)

Okojie, Robert S.; Meredith, Roger D.; Chang, Clarence T.; Savrun, Ender

2014-01-01

Un-cooled, MEMS-based silicon carbide (SiC) static pressure sensors were used for the first time to measure pressure perturbations at temperatures as high as 600 C during laboratory characterization, and subsequently evaluated in a combustor rig operated under various engine conditions to extract the frequencies that are associated with thermoacoustic instabilities. One SiC sensor was placed directly in the flow stream of the combustor rig while a benchmark commercial water-cooled piezoceramic dynamic pressure transducer was co-located axially but kept some distance away from the hot flow stream. In the combustor rig test, the SiC sensor detected thermoacoustic instabilities across a range of engine operating conditions, amplitude magnitude as low as 0.5 psi at 585 C, in good agreement with the benchmark piezoceramic sensor. The SiC sensor experienced low signal to noise ratio at higher temperature, primarily due to the fact that it was a static sensor with low sensitivity.