Investigation of Conditions of Titanium Carbonization - IV

NASA Technical Reports Server (NTRS)

Meerson, G. A.; Lipkes, Y. M.

1949-01-01

In a previous paper, results are presented of accurate investigations of the processes of titanium carbonization and the succeeding titanium carbide decarbonization as related to the phenomenon of the graphitization of soot by heating at a constant temperature in atmospheres of pure hydrogen and carbon monoxide. These tests showed that the processes of titanium carbonization-decarbonization in an atmosphere of pure gases without nitrogen proceed in the same direction as the analogous processes under the conditions of the production furnace. In this case, however, the presence of admixtures of nitrogen changes the quantitative results of the decarbonization process. Thermodynamic computations confirming the results of previous tests conducted at atmospheric pressure and additional tests of titanium carbonization at lowered pressures are presented herein.

Screening tests for Chlamydia trachomatis or Neisseria gonorrhoeae using the cobas 4800 PCR system do not require a second test to confirm: an audit of patients issued with equivocal results at a sexual health clinic in the Northwest of England, U.K.

PubMed

Hopkins, Mark J; Smith, Godfrey; Hart, Ian J; Alloba, Fath

2012-11-01

To assess the clinical utility of supplementary PCRs following a positive cobas 4800 CT/NG PCR screening test result. Laboratory reports, for Chlamydia trachomatis or Neisseria gonorrhoeae, issued to genitourinary medicine patients between April 2010 and April 2011 were reviewed retrospectively. Positive reports were routinely confirmed by supplementary PCRs and N gonorrhoeae culture. Clinical records of patients with unconfirmed positive (equivocal) reports were retrieved to determine if the infection was confirmed by a second sample obtained at patient recall and the impact of this process on antibiotic management. Over 15 000 patients were tested during the study period. The prevalence of chlamydia and gonorrhoea was 972 (5.75%) and 76 (0.50%), respectively. A further 78 chlamydia and 2 gonorrhoea equivocal reports were issued. Only 56 (72%) patients with an equivocal chlamydia report returned to the clinic, and of these, only 41 (73%) gave a second sample to retest. Positive predictive value (PPV) of the PCR screening test was calculated at 98.0% and 97.5% for detection of chlamydia infection from urine and rectal swabs, respectively. Most patients accepted antibiotic treatment before their infection status had been confirmed. Prevalence of gonorrhoea infection was low but the PPV of the screening PCR in urine specimens remained high (98.75%). Equivocal reports introduce delays to patient management, while the risk of unnecessary antibiotic therapy appears acceptable to most patients. The cobas 4800 CT/NG PCR screening assay can achieve UK testing standards (PPV >90%) for chlamydia, and low prevalence gonorrhoea in urine without supplementary tests. A patient-led confirmation algorithm is proposed.

No Face-Like Processing for Objects-of-Expertise in Three Behavioural Tasks

ERIC Educational Resources Information Center

Robbins, Rachel; McKone, Elinor

2007-01-01

In the debate between expertise and domain-specific explanations of "special" processing for faces, a common belief is that behavioural studies support the expertise hypothesis. The present article refutes this view, via a combination of new data and review. We tested dog experts with confirmed good individuation of exemplars of their…

Study and Test to Confirm Automobile Drivetrain Components to Improve Fuel Economy : Volume 2. The Drivetrain Design Process With an Automatic Transmission

DOT National Transportation Integrated Search

1979-05-01

This report presents the key thought processes that are used by the drivetrain designer in matching an engine to a given vehicle with specific performance goals in mind. This report provides those uninitiated in this aspect of automotive design valua...

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design

PubMed Central

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-01-01

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. PMID:25583870

Quantitative assessment of hit detection and confirmation in single and duplicate high-throughput screenings.

PubMed

Wu, Zhijin; Liu, Dongmei; Sui, Yunxia

2008-02-01

The process of identifying active targets (hits) in high-throughput screening (HTS) usually involves 2 steps: first, removing or adjusting for systematic variation in the measurement process so that extreme values represent strong biological activity instead of systematic biases such as plate effect or edge effect and, second, choosing a meaningful cutoff on the calculated statistic to declare positive compounds. Both false-positive and false-negative errors are inevitable in this process. Common control or estimation of error rates is often based on an assumption of normal distribution of the noise. The error rates in hit detection, especially false-negative rates, are hard to verify because in most assays, only compounds selected in primary screening are followed up in confirmation experiments. In this article, the authors take advantage of a quantitative HTS experiment in which all compounds are tested 42 times over a wide range of 14 concentrations so true positives can be found through a dose-response curve. Using the activity status defined by dose curve, the authors analyzed the effect of various data-processing procedures on the sensitivity and specificity of hit detection, the control of error rate, and hit confirmation. A new summary score is proposed and demonstrated to perform well in hit detection and useful in confirmation rate estimation. In general, adjusting for positional effects is beneficial, but a robust test can prevent overadjustment. Error rates estimated based on normal assumption do not agree with actual error rates, for the tails of noise distribution deviate from normal distribution. However, false discovery rate based on empirically estimated null distribution is very close to observed false discovery proportion.

Use of polymerase chain reaction technique to confirm VecTest screening results in Plasmodium falciparum and Plasmodium vivax VK 210 laboratory-infected Anopheles stephensi mosquitoes.

PubMed

Santos-Ciminera, Patricia D; Acheé, Nicole L; Quinnan, Gerald V; Roberts, Donald R

2004-09-01

We evaluated polymerase chain reaction (PCR) to confirm immunoassays for malaria parasites in mosquito pools after a failure to detect malaria with PCR during an outbreak in which pools tested positive using VecTest and enzyme-linked immunosorbent assay (ELISA). We combined VecTest, ELISA, and PCR to detect Plasmodium falciparum and Plasmodium vivax VK 210. Each mosquito pool, prepared in triplicate, consisted of 1 exposed Anopheles stephensi and up to 9 unfed mosquitoes. The results of VecTest and ELISA were concordant. DNA from a subset of the pools, 1 representative of each ratio of infected to uninfected mosquitoes, was extracted and used as template in PCR. All P. vivax pools were PCR positive but some needed additional processing for removal of apparent inhibitors before positive results were obtained. One of the pools selected for P. falciparum was negative by PCR, probably because of losses or contamination during DNA extraction; 2 remaining pools at this ratio were PCR positive. Testing pools by VecTest, ELISA, and PCR is feasible, and PCR is useful for confirmation of immunoassays. An additional step might be needed to remove potential inhibitors from pools prior to PCR.

Tank 241-AY-101 Privatization Push Mode Core Sampling and Analysis Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

TEMPLETON, A.M.

2000-01-12

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AY-101. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AY-101 required to satisfy Data Quality Objectives For RPP Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO) (Nguyen 1999a), Data Quality Objectives For TWRS Privatization Phase I : Confirm Tank T Is An Appropriate Feed Source For Low-Activity Waste Feed Batch X (LAW DQO) (Nguyen 1999b), Low Activitymore » Waste and High-Level Waste Feed Data Quality Objectives (L and H DQO) (Patello et al. 1999), and Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO) (Bloom 1996). Special instructions regarding support to the LAW and HLW DQOs are provided by Baldwin (1999). Push mode core samples will be obtained from risers 15G and 150 to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples; composite the liquids and solids; perform chemical analyses on composite and segment samples; archive half-segment samples; and provide subsamples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AY-101 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plans and are not within the scope of this SAP.« less

Tank 241-AY-101 Privatization Push Mode Core Sampling and Analysis Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

TEMPLETON, A.M.

2000-05-19

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AY-101. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AY-101 required to satisfy ''Data Quality Objectives For RPP Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO)' (Nguyen 1999a), ''Data Quality Objectives For TWRS Privatization Phase I: Confirm Tank T Is An Appropriate Feed Source For Low-Activity Waste Feed Butch X (LAW DQO) (Nguyen 1999b)'', ''Low Activity Wastemore » and High-Level Waste Feed Data Quality Objectives (L&H DQO)'' (Patello et al. 1999), and ''Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO)'' (Bloom 1996). Special instructions regarding support to the LAW and HLW DQOs are provided by Baldwin (1999). Push mode core samples will be obtained from risers 15G and 150 to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples; composite the liquids and solids; perform chemical analyses on composite and segment samples; archive half-segment samples; and provide sub-samples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AY-101 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plans and are not within the scope of this SAP.« less

A Statistics-Based Cracking Criterion of Resin-Bonded Silica Sand for Casting Process Simulation

NASA Astrophysics Data System (ADS)

Wang, Huimin; Lu, Yan; Ripplinger, Keith; Detwiler, Duane; Luo, Alan A.

2017-02-01

Cracking of sand molds/cores can result in many casting defects such as veining. A robust cracking criterion is needed in casting process simulation for predicting/controlling such defects. A cracking probability map, relating to fracture stress and effective volume, was proposed for resin-bonded silica sand based on Weibull statistics. Three-point bending test results of sand samples were used to generate the cracking map and set up a safety line for cracking criterion. Tensile test results confirmed the accuracy of the safety line for cracking prediction. A laboratory casting experiment was designed and carried out to predict cracking of a cup mold during aluminum casting. The stress-strain behavior and the effective volume of the cup molds were calculated using a finite element analysis code ProCAST®. Furthermore, an energy dispersive spectroscopy fractographic examination of the sand samples confirmed the binder cracking in resin-bonded silica sand.

Laboratory Processes for Confirmation of Lymphogranuloma Venereum Infection During a 2015 Investigation of a Cluster of Cases in the United States.

PubMed

Kersh, Ellen N; Pillay, Allan; de Voux, Alex; Chen, Cheng

2017-11-01

In September 2015, the Centers for Disease Control and Prevention were notified of a suspected outbreak investigation of lymphogranuloma venereum (LGV) cases by the Michigan Department of Health and Human Services. The Centers for Disease Control and Prevention offered support with a laboratory-developed polymerase chain reaction test for LGV. This note describes the laboratory workflow and procedures used for the laboratory confirmation of LGV infection.

Concept study of a hydrogen containment process during nuclear thermal engine ground testing

NASA Astrophysics Data System (ADS)

Wang, Ten-See; Stewart, Eric T.; Canabal, Francisco

A new hydrogen containment process was proposed for ground testing of a nuclear thermal engine. It utilizes two thermophysical steps to contain the hydrogen exhaust. First, the decomposition of hydrogen through oxygen-rich combustion at higher temperature; second, the recombination of remaining hydrogen with radicals at low temperature. This is achieved with two unit operations: an oxygen-rich burner and a tubular heat exchanger. A computational fluid dynamics methodology was used to analyze the entire process on a three-dimensional domain. The computed flammability at the exit of the heat exchanger was less than the lower flammability limit, confirming the hydrogen containment capability of the proposed process.

Evaluation of Critical Bandwidth Using Digitally Processed Speech.

DTIC Science & Technology

1982-05-12

observed after re- peating the two tests on persons with confirmed cases of sensorineural hearing impairment. Again, the plotted speech discrimination...quantifying the critical bandwidth of persons on a cli- nical or pre-employment level. The complex portion of the test design (the computer generation of...34super" normal hearing indi- viduals (i.e., those persons with narrower-than-normal cri- tical bands). This ability of the test shows promise as a valuable

55th Annual Fuze Conference

DTIC Science & Technology

2011-05-26

concrete plate and compact soil Confirmation: Complete Success both tests The TDD functioned as programmed; traces show entry and exit from each...concrete target and difference in deceleration levels between concrete and soil configuration The final exit & fire signals were generated as planned...Technical Data Package • Determine Process Capability • FMEA Manufacturing • Determine process capability • Cp = ( USL -LSL)/(6*Sigma) • Cpl

Teaching Grammar through Task-Based Language Teaching to Young EFL Learners

ERIC Educational Resources Information Center

Yildiz, Mustafa; Senel, Mufit

2017-01-01

The present study investigates the effects of Task-Based Language Teaching on students' grammar knowledge in the field of teaching grammar. It has been studied with 32 students from 8th grade during a two-and-a-half-month process. Throughout this process, students firstly are applied a pre-test to examine their level and to confirm whether there…

A false sense of security? Can tiered approach be trusted to accurately classify immunogenicity samples?

PubMed

Jaki, Thomas; Allacher, Peter; Horling, Frank

2016-09-05

Detecting and characterizing of anti-drug antibodies (ADA) against a protein therapeutic are crucially important to monitor the unwanted immune response. Usually a multi-tiered approach that initially rapidly screens for positive samples that are subsequently confirmed in a separate assay is employed for testing of patient samples for ADA activity. In this manuscript we evaluate the ability of different methods used to classify subject with screening and competition based confirmatory assays. We find that for the overall performance of the multi-stage process the method used for confirmation is most important where a t-test is best when differences are moderate to large. Moreover we find that, when differences between positive and negative samples are not sufficiently large, using a competition based confirmation step does yield poor classification of positive samples. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Executive functioning and processing speed in age-related differences in memory: contribution of a coding task.

PubMed

Baudouin, Alexia; Clarys, David; Vanneste, Sandrine; Isingrini, Michel

2009-12-01

The aim of the present study was to examine executive dysfunctioning and decreased processing speed as potential mediators of age-related differences in episodic memory. We compared the performances of young and elderly adults in a free-recall task. Participants were also given tests to measure executive functions and perceptual processing speed and a coding task (the Digit Symbol Substitution Test, DSST). More precisely, we tested the hypothesis that executive functions would mediate the age-related differences observed in the free-recall task better than perceptual speed. We also tested the assumption that a coding task, assumed to involve both executive processes and perceptual speed, would be the best mediator of age-related differences in memory. Findings first confirmed that the DSST combines executive processes and perceptual speed. Secondly, they showed that executive functions are a significant mediator of age-related differences in memory, and that DSST performance is the best predictor.

Change in Soil Porosity under Load

NASA Astrophysics Data System (ADS)

Dyba, V. P.; Skibin, E. G.

2017-11-01

The theoretical basis for the process of soil compaction under various loading paths is considered in the article, the theoretical assumptions are compared with the results of the tests of clay soil on a stabilometer. The variant of the critical state model of the sealing plastic-rigid environment is also considered the strength characteristics of which depend on the porosity coefficient. The loading surface is determined by the results of compression and stabilometrical tests. In order to clarify the results of this task, it is necessary to carry out stabilometric tests under conditions of simple loading, i.e. where the vertical pressure would be proportional to the compression pressure σ3 = kσ1. Within the study the attempts were made to confirm the model given in the beginning of the article by laboratory tests. After the analysis of the results, the provided theoretical assumptions were confirmed.

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design.

PubMed

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-02-28

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Supply Chain Collaboration: Information Sharing in a Tactical Operating Environment

DTIC Science & Technology

2013-06-01

architecture, there are four tiers: Client (Web Application Clients ), Presentation (Web-Server), Processing (Application-Server), Data (Database...organization in each period. This data will be collected to analyze. i) Analyses and Validation: We will do a statistics test in this data, Pareto ...notes, outstanding deliveries, and inventory. i) Analyses and Validation: We will do a statistics test in this data, Pareto analyses and confirmation

A multi-process model of self-regulation: influences of mindfulness, integrative self-knowledge and self-control in Iran.

PubMed

Ghorbani, Nima; Watson, P J; Farhadi, Mehran; Chen, Zhuo

2014-04-01

Self-regulation presumably rests upon multiple processes that include an awareness of ongoing self-experience, enduring self-knowledge and self-control. The present investigation tested this multi-process model using the Five-Facet Mindfulness Questionnaire (FFMQ) and the Integrative Self-Knowledge and Brief Self-Control Scales. Using a sample of 1162 Iranian university students, we confirmed the five-factor structure of the FFMQ in Iran and documented its factorial invariance across males and females. Self-regulatory variables correlated negatively with Perceived Stress, Depression, and Anxiety and positively with Self-Esteem and Satisfaction with Life. Partial mediation effects confirmed that self-regulatory measures ameliorated the disturbing effects of Perceived Stress. Integrative Self-Knowledge and Self-Control interacted to partially mediate the association of Perceived Stress with lower levels of Satisfaction with Life. Integrative Self-Knowledge, alone or in interaction with Self-Control, was the only self-regulation variable to display the expected mediation of Perceived Stress associations with all other measures. Self-Control failed to be implicated in self-regulation only in the mediation of Anxiety. These data confirmed the need to further examine this multi-process model of self-regulation. © 2014 International Union of Psychological Science.

Object Processing in Visual Perception and Action in Children and Adults

ERIC Educational Resources Information Center

Schum, Nina; Franz, Volker H.; Jovanovic, Bianca; Schwarzer, Gudrun

2012-01-01

We investigated whether 6- and 7-year-olds and 9- and 10-year-olds, as well as adults, process object dimensions independent of or in interaction with one another in a perception and action task by adapting Ganel and Goodale's method for testing adults ("Nature", 2003, Vol. 426, pp. 664-667). In addition, we aimed to confirm Ganel and Goodale's…

Psychophysical and Neural Correlates of Auditory Attraction and Aversion

NASA Astrophysics Data System (ADS)

Patten, Kristopher Jakob

This study explores the psychophysical and neural processes associated with the perception of sounds as either pleasant or aversive. The underlying psychophysical theory is based on auditory scene analysis, the process through which listeners parse auditory signals into individual acoustic sources. The first experiment tests and confirms that a self-rated pleasantness continuum reliably exists for 20 various stimuli (r = .48). In addition, the pleasantness continuum correlated with the physical acoustic characteristics of consonance/dissonance (r = .78), which can facilitate auditory parsing processes. The second experiment uses an fMRI block design to test blood oxygen level dependent (BOLD) changes elicited by a subset of 5 exemplar stimuli chosen from Experiment 1 that are evenly distributed over the pleasantness continuum. Specifically, it tests and confirms that the pleasantness continuum produces systematic changes in brain activity for unpleasant acoustic stimuli beyond what occurs with pleasant auditory stimuli. Results revealed that the combination of two positively and two negatively valenced experimental sounds compared to one neutral baseline control elicited BOLD increases in the primary auditory cortex, specifically the bilateral superior temporal gyrus, and left dorsomedial prefrontal cortex; the latter being consistent with a frontal decision-making process common in identification tasks. The negatively-valenced stimuli yielded additional BOLD increases in the left insula, which typically indicates processing of visceral emotions. The positively-valenced stimuli did not yield any significant BOLD activation, consistent with consonant, harmonic stimuli being the prototypical acoustic pattern of auditory objects that is optimal for auditory scene analysis. Both the psychophysical findings of Experiment 1 and the neural processing findings of Experiment 2 support that consonance is an important dimension of sound that is processed in a manner that aids auditory parsing and functional representation of acoustic objects and was found to be a principal feature of pleasing auditory stimuli.

Laser beam heat method reported

NASA Astrophysics Data System (ADS)

Tsuchiya, Hachiro; Goto, Hidekazu

1988-07-01

An outline of research involving the processing method utilizing laser-induced thermochemistry was presented, with the CO2 laser processing of ceramics in CF4 gas used as a practical processing example. It has become clear that it will be possible to conduct laser proccessing of ceramics with high efficiency and high precision by utilizing the thermochemical processes, but it is not believed that the present method is the best one and it is not clear that it can be applied to commercial processing. It is thought that the processing characteristics of this method will be greatly changed by the combination of the atmospheric gas and the material, and it is important to conduct tests on various combinations. However, it is believed that the improvement and development will become possible by theoretically confirming the basic process of the processing, especially of the the thermochemical process between the solid surface and the atmospheric gas molecule. Actually, it is believed that the thermochemical process on the solid surface is quite complicated. For example, it was confirmed that when thermochemical processing the Si monocrystal in the CF4 gas, the processing speed would change by at least 10 times through changing the gas pressure and the mixing O2 gas density. However, conversely speaking, it is believed that the fact that this method is complicated, with many unexplained points and room for research, conceals the possibility of its being applied to various fields, and also, in this sense, the quantitative confirmation of its basic process in an important problem to be solved in the future.

Validation study and routine control monitoring of moist heat sterilization procedures.

PubMed

Shintani, Hideharu

2012-06-01

The proposed approach to validation of steam sterilization in autoclaves follows the basic life cycle concepts applicable to all validation programs. Understand the function of sterilization process, develop and understand the cycles to carry out the process, and define a suitable test or series of tests to confirm that the function of the process is suitably ensured by the structure provided. Sterilization of product and components and parts that come in direct contact with sterilized product is the most critical of pharmaceutical processes. Consequently, this process requires a most rigorous and detailed approach to validation. An understanding of the process requires a basic understanding of microbial death, the parameters that facilitate that death, the accepted definition of sterility, and the relationship between the definition and sterilization parameters. Autoclaves and support systems need to be designed, installed, and qualified in a manner that ensures their continued reliability. Lastly, the test program must be complete and definitive. In this paper, in addition to validation study, documentation of IQ, OQ and PQ concretely were described.

Development and operation of innovative scum to biodiesel pilot-system for the treatment of floatable wastewater scum.

PubMed

Anderson, Erik; Addy, Min; Chen, Paul; Ruan, Roger

2018-02-01

A novel process was developed for the biorefining of floatable wastewater scum and other waste oils from water treatment facilities into biodiesel and other value-added bio-products. To test the scalability and commercial potential of the technology, a 7000 l/year pilot-scale system was designed and built. Scum from a wastewater treatment facility, located in St. Paul, Mn, was collected and converted into methyl esters (biodiesel) according to the process chemistry. All of the incoming and outgoing process streams were sampled, tested, weighed and recorded to calculate both the process efficiency and product quality. Data from the pilot-scale system operation was compared to laboratory results and the theoretically expected values for each individual unit operation. The biodiesel was tested using a third party laboratory and confirmed it met all of the US EPA's test requirements for commercial-grade biodiesel. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimising diagnosis of viraemic hepatitis C infection: the development of a target product profile.

PubMed

Ivanova Reipold, Elena; Easterbrook, Philippa; Trianni, Alessandra; Panneer, Nivedha; Krakower, Douglas; Ongarello, Stefano; Roberts, Teri; Miller, Veronica; Denkinger, Claudia

2017-11-01

The current low access to virological testing to confirm chronic viraemic HCV infection in low- and middle-income countries (LMIC) is limiting the rollout of hepatitis C (HCV) care. Existing tests are complex, costly and require sophisticated laboratory infrastructure. Diagnostic manufacturers need guidance on the optimal characteristics a virological test needs to have to ensure the greatest impact on HCV diagnosis and treatment in LMIC. Our objective was to develop a target product profile (TPP) for diagnosis of HCV viraemia using a global stakeholder consensus-based approach. Based on the standardised process established to develop consensus-based TPPs, we followed five key steps. (i) Identifying key potential global stakeholders for consultation and input into the TPP development process. (ii) Informal priority-setting exercise with key experts to identify the needs that should be the highest priority for the TPP development; (iii) Defining the key TPP domains (scope, performance and operational characteristics and price). (iv) Delphi-like process with larger group of key stakeholder to facilitate feedback on the key TPP criteria and consensus building based on pre-defined consensus criteria. (v) A final consensus-gathering meeting for discussions around disputed criteria. A complementary values and preferences survey helped to assess trade-offs between different key characteristics. The following key attributes for the TPP for a test to confirm HCV viraemic infection were identified: The scope defined is for both HCV detection as well as confirmation of cure. The timeline of development for tests envisioned in the TPP is 5 years. The test should be developed for use by health-care workers or laboratory technicians with limited training in countries with a medium to high prevalence of HCV (1.5-3.5% and >3.5%) and in high-risk populations in low prevalence settings (<1.5%). A clinical sensitivity at a minimum of 90% is considered sufficient (analytical sensitivity of the equivalent of 3000 IU/ml), particularly if the test increases access to testing through an affordable price, increase ease-of-use and feasibility on capillary blood. Polyvalency would be optimal (i.e. ability to test for HIV and others). The only characteristic that full agreement could not be achieved on was the price for a virological test. Discussants felt that to reach the optimal target price substantial trade-offs had to be made (e.g. in regards to sensitivity and integration). The TPP and V&P survey results define the need for an easy-to-use, low cost test to increase access to diagnosis and linkage to care in LMIC.

InSight Lander Solar Array Test

NASA Image and Video Library

2018-01-23

While in the landed configuration for the last time before arriving on Mars, NASA's InSight lander was commanded to deploy its solar arrays to test and verify the exact process that it will use on the surface of the Red Planet. During the test on Jan. 23, 2018 from the Lockheed Martin clean room in Littleton, Colorado, engineers and technicians evaluated that the solar arrays fully deployed and conducted an illumination test to confirm that the solar cells were collecting power. A video is available at https://photojournal.jpl.nasa.gov/catalog/PIA22200

InSight Lander Solar Array Test

NASA Image and Video Library

2018-01-23

While in the landed configuration for the last time before arriving on Mars, NASA's InSight lander was commanded to deploy its solar arrays to test and verify the exact process that it will use on the surface of the Red Planet. During the test on Jan. 23, 2018 from the Lockheed Martin clean room in Littleton, Colorado, engineers and technicians evaluated that the solar arrays fully deployed and conducted an illumination test to confirm that the solar cells were collecting power. A video is available at https://photojournal.jpl.nasa.gov/catalog/PIA22203

InSight Lander Solar Array Test

NASA Image and Video Library

2018-01-23

While in the landed configuration for the last time before arriving on Mars, NASA's InSight lander was commanded to deploy its solar arrays to test and verify the exact process that it will use on the surface of the Red Planet. During the test on Jan. 23, 2018 from the Lockheed Martin clean room in Littleton, Colorado, engineers and technicians evaluated that the solar arrays fully deployed and conducted an illumination test to confirm that the solar cells were collecting power. A video is available at https://photojournal.jpl.nasa.gov/catalog/PIA22202

InSight Lander Solar Array Test

NASA Image and Video Library

2018-01-23

While in the landed configuration for the last time before arriving on Mars, NASA's InSight lander was commanded to deploy its solar arrays to test and verify the exact process that it will use on the surface of the Red Planet. During the test on Jan. 23, 2018 from the Lockheed Martin clean room in Littleton, Colorado, engineers and technicians evaluated that the solar arrays fully deployed and conducted an illumination test to confirm that the solar cells were collecting power. A video is available at https://photojournal.jpl.nasa.gov/catalog/PIA22201

InSight Lander Solar Array Test

NASA Image and Video Library

2018-01-23

While in the landed configuration for the last time before arriving on Mars, NASA's InSight lander was commanded to deploy its solar arrays to test and verify the exact process that it will use on the surface of the Red Planet. During the test on Jan. 23, 2018 from the Lockheed Martin clean room in Littleton, Colorado, engineers and technicians evaluated that the solar arrays fully deployed and conducted an illumination test to confirm that the solar cells were collecting power. A video is available at https://photojournal.jpl.nasa.gov/catalog/PIA22204

Human-rated Safety Certification of a High Voltage Robonaut Lithium-ion Battery

NASA Technical Reports Server (NTRS)

Jeevarajan, Judith; Yayathi, S.; Johnson, M.; Waligora, T.; Verdeyen, W.

2013-01-01

NASA's rigorous certification process is being followed for the R2 high voltage battery program for use of R2 on International Space Station (ISS). Rigorous development testing at appropriate levels to credible off-nominal conditions and review of test data led to design improvements for safety at the virtual cell, cartridge and battery levels. Tests were carried out at all levels to confirm that both hardware and software controls work. Stringent flight acceptance testing of the flight battery will be completed before launch for mission use on ISS.

Analysis of the release process of phenylpropanolamine hydrochloride from ethylcellulose matrix granules III. Effects of the dissolution condition on the release process.

PubMed

Fukui, Atsuko; Fujii, Ryuta; Yonezawa, Yorinobu; Sunada, Hisakazu

2006-08-01

In the pharmaceutical preparation of a controlled release drug, it is very important and necessary to understand the entire release properties. As the first step, the dissolution test under various conditions is selected for the in vitro test, and usually the results are analyzed following Drug Approval and Licensing Procedures. In this test, 3 time points for each release ratio, such as 0.2-0.4, 0.4-0.6, and over 0.7, respectively, should be selected in advance. These are analyzed as to whether their values are inside or outside the prescribed aims at each time point. This method is very simple and useful but the details of the release properties can not be clarified or confirmed. The validity of the dissolution test in analysis using a combination of the square-root time law and cube-root law equations to understand all the drug release properties was confirmed by comparing the simulated value with that measured in the previous papers. Dissolution tests under various conditions affecting drug release properties in the human body were then examined, and the results were analyzed by both methods to identify their strengths and weaknesses. Hereafter, the control of pharmaceutical preparation, the manufacturing process, and understanding the drug release properties will be more efficient. It is considered that analysis using the combination of the square-root time law and cube-root law equations is very useful and efficient. The accuracy of predicting drug release properties in the human body was improved and clarified.

[The heuristics of reaching a diagnosis].

PubMed

Wainstein, Eduardo

2009-12-01

Making a diagnosis in medicine is a complex process in which many cognitive and psychological issues are involved. After the first encounter with the patient, an unconscious process ensues to suspect the presence of a particular disease. Usually, complementary tests are requested to confirm the clinical suspicion. The interpretation of requested tests can be biased by the clinical diagnosis that was considered in the first encounter with the patient. The awareness of these sources of error is essential in the interpretation of the findings that will eventually lead to a final diagnosis. This article discusses some aspects of the heuristics involved in the adjudication of priory probabilities and provides a brief review of current concepts of the reasoning process.

BASIC BIOCHEMICAL AND CLINICAL ASPECTS OF NONINVASIVE TESTS HELIC.

PubMed

Dmitrienko, M A; Dmitrienko, V S; Kornienko, E A; Parolova, N I; Colomina, E O; Aronov, E B

Biochemical process that lay in the core of non-invasive detection of Helico ho cter pylod with the help of HELIC Ammonia breath test, manufactured by AMA Co Ltd., St.Petersburg, is shown. Patents from various countries, describing ammonia as H.pyiori diagnostic marker, are reviewed. Approaches for evaluation of efficacy of the test-system are analyzed, validation and verification data is provided. High diagnostic characteristics are confirmed by the results of comparative studies on patients of different age groups, reaching 97% sensitivity and 96% specificity.

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Pensinger, Stuart J.; Pickering, Karen D.

2012-01-01

The Brine Residual In-Containment (BRIC) concept is being developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management designs typically used in spacecraft systems. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches currently envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other early observations from testing are reported.

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Pensinger, Stuart; Pickering, Karen D.

2011-01-01

The Brine Residual In-Containment (BRIC) concept was developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying for these solutions. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management in spacecraft brine dewatering system designs. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other observations from testing are reported.

Sanger Confirmation Is Required to Achieve Optimal Sensitivity and Specificity in Next-Generation Sequencing Panel Testing.

PubMed

Mu, Wenbo; Lu, Hsiao-Mei; Chen, Jefferey; Li, Shuwei; Elliott, Aaron M

2016-11-01

Next-generation sequencing (NGS) has rapidly replaced Sanger sequencing as the method of choice for diagnostic gene-panel testing. For hereditary-cancer testing, the technical sensitivity and specificity of the assay are paramount as clinicians use results to make important clinical management and treatment decisions. There is significant debate within the diagnostics community regarding the necessity of confirming NGS variant calls by Sanger sequencing, considering that numerous laboratories report having 100% specificity from the NGS data alone. Here we report our results from 20,000 hereditary-cancer NGS panels spanning 47 genes, in which all 7845 nonpolymorphic variants were Sanger- sequenced. Of these, 98.7% were concordant between NGS and Sanger sequencing and 1.3% were identified as NGS false-positives, located mainly in complex genomic regions (A/T-rich regions, G/C-rich regions, homopolymer stretches, and pseudogene regions). Simulating a false-positive rate of zero by adjusting the variant-calling quality-score thresholds decreased the sensitivity of the assay from 100% to 97.8%, resulting in the missed detection of 176 Sanger-confirmed variants, the majority in complex genomic regions (n = 114) and mosaic mutations (n = 7). The data illustrate the importance of setting quality thresholds for panel testing only after thousands of samples have been processed and the necessity of Sanger confirmation of NGS variants to maintain the highest possible sensitivity. Copyright © 2016 American Society for Investigative Pathology and the Association for Molecular Pathology. Published by Elsevier Inc. All rights reserved.

Incremental Feeding High-Pressure Sliding for Grain Refinement of Large-Scale Sheets: Application to Inconel 718

NASA Astrophysics Data System (ADS)

Takizawa, Yoichi; Sumikawa, Kosei; Watanabe, Kyohei; Masuda, Takahiro; Yumoto, Manabu; Kanai, Yuta; Otagiri, Yoshiharu; Horita, Zenji

2018-03-01

This study updates a process of high-pressure sliding (HPS) recently developed as a severe plastic deformation process under high pressure for grain refinement of sheet samples. The updated version, which we call the incremental feeding HPS (IF-HPS), consists of sliding for SPD and feeding for upsizing the SPD-processed area so that, without increasing the capacity of processing facility, it is possible to cover a much larger area with an SPD-processed ultrafine-grained structure with a grain size of 120 nm. For the IF-HPS processing, anvils with flat surfaces but without grooves are used in an unconstrained condition, and the feeding distance is set equal to the deformed width. A Ni-based superalloy (Inconel 718) is processed by the IF-HPS under 4 GPa at room temperature, and it is possible to obtain an SPD-processed sheet with dimensions of approximately 100 × 100 × 1 mm3. Strain distribution and evolution were examined by hardness measurement and simulation using a finite element method. Tensile tests were conducted using tensile specimens extracted from the IF-HPS-processed sheet. Advent of high strain rate superplasticity with the total elongation of more than 400 pct was confirmed by pulling the tensile specimens with an initial strain rate of 2.0 × 10-2 s-1 at a temperature as low as 1073 K. The formability of the IF-HPS-processed sheet was confirmed by successful cup forming. It was also confirmed that the restoration after the superplastic deformation was feasible by subjecting to conventional heat treatment used for Inconel 718.

Design, evaluation, and fabrication of low-cost composite blades for intermediate-size wind turbines

NASA Technical Reports Server (NTRS)

Weingart, O.

1981-01-01

Low cost approaches for production of 60 ft long glass fiber/resin composite rotor blades for the MOD-OA wind turbine were identified and evaluated. The most cost-effective configuration was selected for detailed design. Subelement and subscale specimens were fabricated for testing to confirm physical and mechanical properties of the composite blade materials, to develop and evaluate blade fabrication techniques and processes, and to confirm the structural adequacy of the root end joint. Full-scale blade tooling was constructed and a partial blade for tool and process tryout was built. Then two full scale blades were fabricated and delivered to NASA-LeRC for installation on a MOD-OA wind turbine at Clayton, New Mexico for operational testing. Each blade was 60 ft. long with 4.5 ft. chord at root end and 2575 lbs weight including metal hub adapter. The selected blade configuration was a three cell design constructed using a resin impregnated glass fiber tape winding process that allows rapid wrapping of primarily axially oriented fibers onto a tapered mandrel, with tapered wall thickness. The ring winder/transverse filament tape process combination was used for the first time on this program to produce entire rotor blade structures. This approach permitted the complete blade to be wound on stationary mandrels, an improvement which alleviated some of the tooling and process problems encountered on previous composite blade programs.

High friction interactive aircraft tire-runway systems

NASA Technical Reports Server (NTRS)

Clark, S. K.

1974-01-01

The principle of utilizing geometric interaction between runway asperities and tire pattern design is discussed, and a theoretical basis is presented for substantial enhancement of frictional effects by this process. Test data confirming this is given. First order analytical expressions are given for the increased friction coefficients and for the engagement distances required. High speed friction data on a 7.00 x 8 aircraft tire is presented confirming this. Example design geometries are shown for the tire tread groove pattern, and designs and materials are discussed for the asperity grid and its attachment system.

Effect of normal aging and of Alzheimer's disease on, episodic memory.

PubMed

Le Moal, S; Reymann, J M; Thomas, V; Cattenoz, C; Lieury, A; Allain, H

1997-01-01

Performances of 12 patients with Alzheimer's disease (AD), 15 healthy elderly subjects and 20 young healthy volunteers were compared on two episodic memory tests. The first, a learning test of semantically related words, enabled an assessment of the effect of semantic relationships on word learning by controlling the encoding and retrieval processes. The second, a dual coding test, is about the assessment of automatic processes operating during drawings encoding. The results obtained demonstrated quantitative and qualitative differences between the population. Manifestations of episodic memory deficit in AD patients were shown not only by lower performance scores than in elderly controls, but also by the lack of any effect of semantic cues and the production of a large number of extra-list intrusions. Automatic processes underlying dual coding appear to be spared in AD, although more time is needed to process information than in young or elderly subjects. These findings confirm former data and emphasize the preservation of certain memory processes (dual coding) in AD which could be used in future therapeutic approaches.

Molecular detection of Staphylococcus aureus resistant to temperature in milk and its products

NASA Astrophysics Data System (ADS)

Sutejo, Stephani Valentina Harda; Amarantini, Charis; Budiarso, Tri Yahya

2017-11-01

Contamination of Staphylococcus aureus on milk can cause intoxication and infection by Staphylococcal enterotoxin. It has nuc gene, coding thermonuclease enzyme (TNase) that is responsible for nature of resistance in the heating process. This study was conducted to identify nuc gene of as S. aureus isolated from milk and its products like ultra-high temperature, sterile milk, sweetened condensed milk, formula milk, café/milk street traders and fresh milk. Biochemical identification was conducted by using carbohydrate fermentation tests and confirmed by API Staph. Molecular confirmation by amplification of nuc gene using PCR. Based on the results of confirmation using API Staph, all isolates were confirmed as S. aureus with index determinant percentage of 97%. An amplicon product of 270 bp was gained in all isolates. It is concluded that isolate of S. aureus has nuc gene.

Hot-melt extrusion as a continuous manufacturing process to form ternary cyclodextrin inclusion complexes.

PubMed

Thiry, Justine; Krier, Fabrice; Ratwatte, Shenelka; Thomassin, Jean-Michel; Jerome, Christine; Evrard, Brigitte

2017-01-01

The aim of this study was to evaluate hot-melt extrusion (HME) as a continuous process to form cyclodextrin (CD) inclusion complexes in order to increase the solubility and dissolution rate of itraconazole (ITZ), a class II model drug molecule of the Biopharmaceutics Classification System. Different CD derivatives were tested in a 1:1 (CD:ITZ) molar ratio to obtain CD ternary inclusion complexes in the presence of a polymer, namely Soluplus ® (SOL). The CD used in this series of experiments were β-cyclodextrin (βCD), hydroxypropyl-β-cyclodextrin (HPβCD) with degrees of substitution of 0.63 and 0.87, randomly methylated β-cyclodextrin (Rameb ® ), sulfobutylether-β-cyclodextrin (Captisol ® ) and methyl-β-cyclodextrin (Crysmeb ® ). Rheology testing and mini extrusion using a conical twin screw mini extruder were performed to test the processability of the different CD mixtures since CD are not thermoplastic. This allowed Captisol ® and Crysmeb ® to be discarded from the study due to their high impact on the viscosity of the SOL/ITZ mixture. The remaining CD were processed by HME in an 18mm twin screw extruder. Saturation concentration measurements confirmed the enhancement of solubility of ITZ for the four CD formulations. Biphasic dissolution tests indicated that all four formulations had faster release profiles compared to the SOL/ITZ solid dispersion. Formulations of HPβCD 0.63 and Rameb ® even reached 95% of ITZ released in both phases after 1h. The formulations were characterized using thermal differential scanning calorimetry and attenuated total reflectance infra-red analysis. These analyses confirmed that the increased release profile was due to the formation of ternary inclusion complexes. Copyright © 2016 Elsevier B.V. All rights reserved.

Huntington's disease in Greece: the experience of 14 years.

PubMed

Panas, M; Karadima, G; Vassos, E; Kalfakis, N; Kladi, A; Christodoulou, K; Vassilopoulos, D

2011-12-01

A large scale genetic and epidemiological study of Huntington's disease (HD) was carried out in Greece from January 1995 to December 2008. Diagnostic testing was carried out in 461 symptomatic individuals, while 256 were tested for presymptomatic purposes. The diagnosis of HD with a CAG expansion ≥ 36 was confirmed in 278 symptomatic individuals. The prevalence of HD in Greece was estimated at approximately 2.5 to 5.4:100,000, while the mean minimum incidence was estimated at 2.2 to 4.4 per million per year. The molecular diagnosis of HD was confirmed in the majority of patients (84.4%) sent for confirmation. The false-positive cases 15.6% were characterized by the absence of a family history of HD and the presence of an atypical clinical picture. The uptake of predictive testing for HD was 8.6%. A prenatal test was requested in six pregnancies. The findings of our study do not differ significantly from those of similar studies from other European countries despite the relative genetic isolation of Greece. Of interest is the identification of clusters of HD in Greece. The presence or absence of a family history of HD should be interpreted cautiously, during the diagnostic process. © 2010 John Wiley & Sons A/S.

Utilizing Secondary Agricultural Education Programs to Deliver Evidence-Based Grain Safety Training for Young and Beginning Workers.

PubMed

Cheng, Yuan-Hsin; Field, William E; Tormoehlen, Roger L; French, Brian F

2017-01-01

Purdue University's Agricultural Safety and Health Program (PUASHP) has collaborated with secondary agricultural education programs, including FFA Chapters, for over 70 years to deliver and promote agricultural safety and health programming. With support from a U.S. Department of Labor Susan Harwood Program grant, PUASHP utilized a Developing a Curriculum (DACUM) process to develop, implement, and evaluate an evidence-based curriculum for use with young and beginning workers, ages 16-20, exposed to hazards associated with grain storage and handling. The primary audience was students enrolled in secondary agricultural education programs. A review of the literature identified a gap in educational resources that specifically addresses this target population. The curriculum developed was based on fatality and injury incident data mined from Purdue's Agricultural Confined Space Incident Database and input from a panel of experts. The process identified 27 learning outcomes and finalized a pool of test questions, supported by empirical evidence and confirmed by a panel of experts. An alignment process was then completed with the current national standards for secondary agricultural education programs. Seventy-two youth, ages 16-20, enrolled in secondary-school agricultural education programs, and a smaller group of post-secondary students under the age of 21 interested in working in the grain industry pilot tested the curriculum. Based on student and instructor feedback, the curriculum was refined and submitted to OSHA for approval as part of OSHA's online training resources. The curriculum was delivered to 3,665 students, ages 16-20. A total of 346 pre- and post-tests were analyzed, and the results used to confirm content validity and assess knowledge gain. Findings led to additional modifications to curriculum content, affirmed knowledge gain, and confirmed appropriateness for use with secondary agricultural education programs. The curriculum has been promoted nationally and made available for free download from www.agconfinedspaces.org . Findings further confirmed the value of delivering safety programming through established programs such as secondary agricultural education programs and FFA Chapters serving youth.

Occupational asthma due to polyethylene shrink wrapping (paper wrapper's asthma).

PubMed Central

Gannon, P F; Burge, P S; Benfield, G F

1992-01-01

Occupational asthma due to the pyrolysis products of polyvinyl chloride (PVC) produced by shrink wrapping processes has previously been reported. The first case of occupational asthma in a shrink wrap worker using a different plastic, polyethylene, is reported; the association was confirmed by specific bronchial provocation testing. PMID:1440477

Bioremediation process on Brazil shoreline. Laboratory experiments.

PubMed

Rosa, Anabela P; Triguis, Jorge A

2007-11-01

Bioremediation technique can be considered a promising alternative to clean oil spills using microbial processes to reduce the concentration and/or the toxicity of pollutants. To understand the importance of this work we must know that there is only little research performed to date using bioremediation techniques to clean oil spills in tropical countries. So, the main objective of this work is to analyze the behavior of a laboratory's bioremediation test using nutrients on coastal sediments. The bioremediation process is followed through geochemical analysis during the tests. This organic material is analyzed by medium pressure liquid chromatography (MPLC), gas chromatography/flame ionization detection (GC/FID) and gas chromatography/ mass spectrometry. By microbial counting, the number of total bacteria and degrading bacteria is determined during the experiments, in order to confirm the effectiveness of the bioremediation process. The seawater obtained throughout the bioremediation process is analyzed for nutrients grade (phosphate and ammonium ions) and also for its toxicity (Microtox tests) due the presence of hydrocarbons and fertilizer. The results from the geochemical analyses of the oil show a relative decrease in the saturated hydrocarbon fraction that is compensated by a relative enrichment on polar compounds. It's confirmed by the fingerprint evaluation where it is possible to see a complete reduction of the normal alkanes followed by isoprenoids. Seawater analysis done by toxicity and nutrients analysis, such as microbial counting (total and degrading bacteria), confirm the fertilizer effectiveness during the bioremediation process. Results from simulating test using NPK, a low-price plant fertilizer, suggest that it's able to stimulate the degradation process. Results from medium pressure liquid chromatography (MPLC), done at two different depths (surface and subsurface), show different behavior during the biodegradation process where the later is seen to be more susceptible to microbial attack. Data from bioremediation unit shows a bigger reduction of the saturated fraction, followed by some smaller reduction of aromatic fractions, compensated by a relative increase from polar compounds (NSO). n-C17/pristane, n-C18/ fitane and pristane/fitane rates show constant values for the unity control, different from bioremediation samples which have a significant reduction, especially on subsurface areas, where a strong fall in the rates, seen to be reduced to zero over twenty days, had occurred during the first ten days. However, sample surfaces are reduced to zero in thirty days of experiments, proving that biodegradation is better on subsurfaces. Gaseous chromatography/mass spectrometry (CG/MS) analysis shows constant values to cyclic biomarker rates and aromatic compounds, suggesting that the biodegradation process is not strong enough to reduce these composites. Microbial analysis shows a reduction on heterotrophic (total bacteria) number from control unit, probably because the bacteria uses the spill oil like carbon source and energy. However, the number increases on bioremediation unit, because it uses NPK like a biostimulator. The hydrocarbonoclastic number isn't enough on the first moment, but it's detected after 30 days and quantified in all units, showing big values especially in bioremediation. Toxicity tests confirm that NPK fertilizer does not intoxicate the shoreline during the application of the bioremediation technique. Some nutrient concentration shows high values of ammonium and phosphate per bioremediation unit, reducing by the end of the experiment. Results reached the goal, finding a proper nutrient (NPK fertilizer) to stimulate the biodegradation process, growing bacteria responsible for reducing impact-contaminated coast ambient by oil spills. Chemical analysis of oil shows a reduction in the saturated fraction with a relative enrichment in polar composites (NSO) and the aromatic fraction from oil remaining constant. Subsurface samples show more biodegradation than surface samples, probably because the first one has higher humidity. Linear alcanes are more biodegraded than isoprenoids, confirming the biodegradation susceptibility order. Saturated cyclic biomarkers and aromatic compounds show constant behavior maybe because the nutrients or time was not enough for microorganismic attack. Fertilizer does not demonstrate any toxic effects in local biota so that it does not compromise the technique applicability and the environment is not saturated by nutrients during the simulation, especially since the coastal environment is an open system affected daily by tides. Therefore, bioremediation tests can be classified as moderate, reaching level 5 in the classification scale by Peters & Moldowan (1993). The use of marine environment by the petroleum industry on exploration, production and transportation operation, transform this oil to become the most important pollutant in the oceans. Bioremediation is an important technique used to clean spilled oil impacting on shorelines, accelerating the biodegradation process by using fertilizer growing the microorganisms responsible for decontaminating the environment. We recommend confirming the efficiency of NPK nutrient used on bioremediation simulating experiments on beaches, while monitoring the chemical changes long-term. NPK fertilizer can be used to stimulate the biodegradation process on shoreline impacted by spilled oil.

Digital Fly-By-Wire Flight Control Validation Experience

NASA Technical Reports Server (NTRS)

Szalai, K. J.; Jarvis, C. R.; Krier, G. E.; Megna, V. A.; Brock, L. D.; Odonnell, R. N.

1978-01-01

The experience gained in digital fly-by-wire technology through a flight test program being conducted by the NASA Dryden Flight Research Center in an F-8C aircraft is described. The system requirements are outlined, along with the requirements for flight qualification. The system is described, including the hardware components, the aircraft installation, and the system operation. The flight qualification experience is emphasized. The qualification process included the theoretical validation of the basic design, laboratory testing of the hardware and software elements, systems level testing, and flight testing. The most productive testing was performed on an iron bird aircraft, which used the actual electronic and hydraulic hardware and a simulation of the F-8 characteristics to provide the flight environment. The iron bird was used for sensor and system redundancy management testing, failure modes and effects testing, and stress testing in many cases with the pilot in the loop. The flight test program confirmed the quality of the validation process by achieving 50 flights without a known undetected failure and with no false alarms.

[Practical guidelines for genetic testing in cardiovascular diseases].

PubMed

Reinhard, W; Trenkwalder, T; Schunkert, H

2017-08-01

In the last decade, genetic testing for cardiovascular disorders has become more and more relevant. Progress in molecular genetics has led to new opportunities for diagnostics, improved risk prediction and could lead to novel therapeutic approaches. Genetic diagnostic testing is relevant for both confirming a diagnosis as well as deciding on therapeutic consequences, if applicable. Furthermore, predictive testing in family members for specific cardiovascular diseases is now a standard procedure in holistic patient management. The process of genetic testing as well as documentation requirements and discussion of test results with patients are subject to legal regulations. These regulations might be confusing for clinical practitioners/cardiologists. The aim of this article is to provide a clinical framework for genetic testing. First, we explain the legal and ethical background. Second, we illustrate the process of genetic testing step by step and present updates on remuneration. Finally, we discuss the significance of genetic testing and specific disease indications in cardiology.

Aspects of the tribological behaviour of powders recycled from rapid steel treated sub-zero

NASA Astrophysics Data System (ADS)

Radu, S.; Ciobanu, M.

2017-02-01

The recycling of high-alloyed steels represents a significant opportunity in Powder Metallurgy as it permits the use of raw materials with relatively low prices compared to the conventional methods. Recycling can be achieved by two methods: from spraying debris resulted from worn cutting tools and processes obtained from processing chip drilling and re-sharpening of tools. The research aims to confirm that wastes from rapid steels can become, by the successive processing, metal powders that can thereafter be used for cutting tools of lathe type removable plate. After pressing and sintering the recycling powder, cylindrical samples were obtained that were subsequently applied a subcritical annealing. Wear tests conducted on a tribometer type TRB-01-02541 confirmed that their wear resistance is superior to the same samples that were sintered, hardened and tempered in oil. This paper was accepted for publication in Proceedings after double peer reviewing process but was not presented at the Conference ROTRIB’16.

Load Testing of GFRP Composite U-Shape Footbridge

NASA Astrophysics Data System (ADS)

Pyrzowski, Łukasz; Miśkiewicz, Mikołaj; Chróścielewski, Jacek; Wilde, Krzysztof

2017-10-01

The paper presents the scope of load tests carried out on an innovative shell composite footbridge. The tested footbridge was manufactured in one production cycle and has no components made from materials other than GFRP laminates and PET foam. The load tests, performed on a 14-m long structure, were the final stage of a research program in the Fobridge project carried out in cooperation with: Gdańsk University of Technology (leader), Military University of Technology in Warsaw, and ROMA Co. Ltd.; and co-financed by NCBR. The aim of the tests was to confirm whether the complex U-shape sandwich structure behaves correctly. The design and technological processes involved in constructing this innovative footbridge required the solving of many problems: absence of standards for design of composite footbridges, lack of standardized material data, lack of guidelines for calculation and evaluation of material strength, and no guidelines for infusion of large, thick sandwich elements. Obtaining answers during the design process demanded extensive experimental tests, development of material models, validation of models, updating parameters and extensive numerical parametric studies. The technological aspects of infusion were tested in numerous trials involving the selection of material parameters and control of the infusion parameters. All scientific validation tests were successfully completed and market assessment showed that the proposed product has potential applications; it can be used for overcoming obstacles in rural areas and cities, as well as in regions affected by natural disasters. Load testing included static and dynamic tests. During the former, the span was examined at 117 independent measurement points. The footbridge was loaded with concrete slabs in different configurations. Their total weight ranged from 140 kN up to 202 kN. The applied load at the most heavily loaded structural points caused an effect from 89% to 120%, compared to the load specified by standards (5 kN/m2). Dynamic tests included standard actions (walking, running, synchronous jumps) as well as aggressive tests, all designed to confirm the usability of the footbridge. The performed trials allowed the identification of the modal and damping parameters of the structure. The designated first natural frequency with a value of 7.8 Hz confirmed the correctness of the U-shape cross-section design due to its significant structural rigidity.

Advanced thermionic energy conversion

NASA Technical Reports Server (NTRS)

Britt, E. J.; Fitzpatrick, G. D.; Hansen, L. K.; Rasor, N. S.

1974-01-01

Basic analytical and experimental exploration was conducted on several types of advanced thermionic energy converters, and preliminary analysis was performed on systems utilizing advanced converter performance. The Pt--Nb cylindrical diode which exhibited a suppressed arc drop, as described in the preceding report, was reassembled and the existence of the postulated hydrid mode of operation was tentatively confirmed. Initial data obtained on ignited and unignited triode operation in the demountable cesium vapor system essentially confirmed the design principles developed in earlier work, with a few exceptions. Three specific advanced converter concepts were selected as candidates for concentrated basic study and for practical evaluation in fixed-configuration converters. Test vehicles and test stands for these converters and a unique controlled-atmosphere station for converter assembly and processing were designed, and procurement was initiated.

Hypersensitivity reactions to metal implants: laboratory options.

PubMed

Carossino, Anna Maria; Carulli, Christian; Ciuffi, Simone; Carossino, Roberto; Zappoli Thyrion, Giorgia Donata; Zonefrati, Roberto; Innocenti, Massimo; Brandi, Maria Luisa

2016-11-23

All implant compounds undergo an electrochemical process when in contact with biological fluids, as well as mechanical corrosion due to abrasive wear, with production of metal debris that may inhibit repair processes. None of the commonly-used methods can diagnose implant allergies when used singly, therefore a panel of tests should be performed on allergic patients as pre-operative screening, or when a postoperative metal sensitisation is suspected. We analysed patients with painful prostheses and subjects prone to allergies using the Patch Test in comparison with the Lymphocyte Transformation Test. Cytokine production was evaluated to identify prognostic markers for early diagnosis of aseptic loosening. Metal debris endocytosis and cytoskeletal rearrangement was visualised by confocal microscopy. Our results demonstrate that the Lymphocyte Transformation Test can identify patients who have a predisposition to develop allergic reactions and can confirm the diagnosis of hypersensitivity in patients with painful prostheses. The prevalence of a Th2-cytokine pattern may be used to identify predisposition to the development of allergic diseases, while the selective presence of osteoclastogenic cytokines may be used as predictor of a negative outcome in patients with painful prosthesis. The hypothesis of the prognostic value of these cytokines as early markers of aseptic loosening is attractive, but its confirmation would require extensive testing. The Lymphocyte Transformation Test is the most suitable method for testing systemic allergies. We suggest that the combined use of the Patch Test and the Lymphocyte Transformation Test, associated with cytokine detection in selected patients, could provide a useful tool for preventive evaluation of immune reactivity in patients undergoing primary joint replacement surgery, and for clinical monitoring of the possible onset of a metal sensitization in patients with implanted devices.

The role of responsibility and fear of guilt in hypothesis-testing.

PubMed

Mancini, Francesco; Gangemi, Amelia

2006-12-01

Recent theories argue that both perceived responsibility and fear of guilt increase obsessive-like behaviours. We propose that hypothesis-testing might account for this effect. Both perceived responsibility and fear of guilt would influence subjects' hypothesis-testing, by inducing a prudential style. This style implies focusing on and confirming the worst hypothesis, and reiterating the testing process. In our experiment, we manipulated the responsibility and fear of guilt of 236 normal volunteers who executed a deductive task. The results show that perceived responsibility is the main factor that influenced individuals' hypothesis-testing. Fear of guilt has however a significant additive effect. Guilt-fearing participants preferred to carry on with the diagnostic process, even when faced with initial favourable evidence, whereas participants in the responsibility condition only did so when confronted with an unfavourable evidence. Implications for the understanding of obsessive-compulsive disorder (OCD) are discussed.

Testing the Structure of Hydrological Models using Genetic Programming

NASA Astrophysics Data System (ADS)

Selle, B.; Muttil, N.

2009-04-01

Genetic Programming is able to systematically explore many alternative model structures of different complexity from available input and response data. We hypothesised that genetic programming can be used to test the structure hydrological models and to identify dominant processes in hydrological systems. To test this, genetic programming was used to analyse a data set from a lysimeter experiment in southeastern Australia. The lysimeter experiment was conducted to quantify the deep percolation response under surface irrigated pasture to different soil types, water table depths and water ponding times during surface irrigation. Using genetic programming, a simple model of deep percolation was consistently evolved in multiple model runs. This simple and interpretable model confirmed the dominant process contributing to deep percolation represented in a conceptual model that was published earlier. Thus, this study shows that genetic programming can be used to evaluate the structure of hydrological models and to gain insight about the dominant processes in hydrological systems.

Machining of Aircraft Titanium with Abrasive-Waterjets for Fatigue Critical Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, H. T.; Hovanski, Yuri; Dahl, Michael E.

2010-10-04

Laboratory tests were conducted to determine the fatigue performance of AWJ-machined aircraft titanium. Dog-bone specimens machined with AWJs were prepared and tested with and without sanding and dry-grit blasting with Al2O3 as secondary processes. The secondary processes were applied to remove the visual appearance of AWJ-generated striations and to clean up the garnet embedment. The fatigue performance of AWJ-machined specimens was compared with baseline specimens machined with CNC milling. Fatigue test results not only confirmed the findings of the aluminum dog-bone specimens but also further enhance the fatigue performance. In addition, titanium is known to be notoriously difficult to cutmore » with contact tools while AWJs cut it 34% faster than stainless steel. AWJ cutting and dry-grit blasting are shown to be a preferred combination for processing aircraft titanium that is fatigue critical.« less

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR BENCH-SCALE REFORMER TREATABILITY STUDIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2011-02-11

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Bench-Scale Reforming testing. The type, quantity, and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluidized bed steam reformer. A determination of the adequacy of the fluidized bed steam reformer process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the fluidized bed steam reformer process is to select archived waste samples from the 222-S Laboratory that will be used in a bench scale tests. Analyses of the selected samples will be required to confirm the samples meet the shipping requirements and for comparison to the bench scale reformer (BSR) test sample selection requirements.« less

The occurrence, transmission, virulence and antibiotic resistance of Listeria monocytogenes in fish processing plant.

PubMed

Skowron, Krzysztof; Kwiecińska-Piróg, Joanna; Grudlewska, Katarzyna; Świeca, Agnieszka; Paluszak, Zbigniew; Bauza-Kaszewska, Justyna; Wałecka-Zacharska, Ewa; Gospodarek-Komkowska, Eugenia

2018-06-13

The aim of this research was to investigate the occurrence of Listeria monocytogenes in fish and fish processing plant and to determine their transmission, virulence and antibiotic resistance. L. monocytogenes was isolated according to the ISO 11290-1. The identification of L. monocytogenes was confirmed by multiplex PCR method. Genetic similarity of L. monocytogenes strains was determined with the Pulsed-Filed Gene Electrophoresis (PFGE) method. The multiplex PCR was used for identification of L. monocytogenes serogroups and detection of selected virulence genes (actA, fbpA, hlyA, iap, inlA, inlB, mpl, plcA, plcB, prfA). The L. monocytogens isolates susceptibility to penicillin, ampicillin, meropenem, erythromycin, trimethoprim/sulfamethoxazole was evaluated with disc diffusion method according to EUCAST v. 7.1. The presence of 237 L. monocytogenes isolates (before genetic similarity assessment) in 614 examined samples was confirmed. After strain differentiation by PFGE techniques the presence of 161 genetically different strains were confirmed. The genetic similarity of the examined isolates suggested that the source of the L. monocytogenes strains were fishes originating from farms. All tested strains possessed all detected virulence genes. Among examined strains, the most (26, 38.6%) belonged to the group 1/2a-3a. The most of tested strains were resistant to erythromycin (47.1%) and trimethoprim/sulfamethoxazole (47.1%). Copyright © 2018. Published by Elsevier B.V.

Understanding the Process of Stereotype Threat: A Review of Mediational Variables and New Performance Goal Directions

ERIC Educational Resources Information Center

Smith, Jessi L.

2004-01-01

Stereotype threat is a situational experience in which an individual feels vulnerable and pressured by the possibility of confirming or being judged by a stereotype. This threatening experience leads to performance decrements, even among highly skilled individuals. This article chronicles empirically tested mechanisms for how stereotype threat…

Key Lessons for the Design and Integration of Virtual Environments in Secondary Science.

ERIC Educational Resources Information Center

Crosier, Joanna K.; Cobb, Sue; Wilson, John R.

2002-01-01

Discusses a three-year research project in which a virtual environment to teach radioactivity in secondary schools in the United Kingdom was developed and tested. Emphasizes the importance of involving teachers through the development process and confirms the importance of school-based evaluation studies in the development and evaluation of…

Analysis of the release process of phenylpropanolamine hydrochloride from ethylcellulose matrix granules IV.(1)) Evaluation of the controlled release properties for in vivo and in vitro release systems.

PubMed

Fukui, Atsuko; Fujii, Ryuta; Yonezawa, Yorinobu; Sunada, Hisakazu

2007-11-01

In the pharmaceutical preparation of a controlled release drug, it is very important and necessary to understand the release properties. The dissolution test is a very important and useful method for understanding and predicting drug-release properties. It was readily confirmed in the previous paper that the release process could be assessed quantitatively by a combination of the square-root time law and cube-root law equations for ethylcellulose (EC) matrix granules of phenylpropanolamine hydrochloride (PPA). In this paper EC layered granules were used in addition to EC matrix. The relationship between release property and the concentration of PPA in plasma after administration using beagle dogs were examined. Then it was confirmed that the correlativity for EC layered granules and EC matrix were similar each other. Therefore, it was considered that the dissolution test is useful for prediction of changes in concentration of PPA in the blood with time. And it was suggested that EC layered granules were suitable as a controlled release system as well as EC matrix.

Examining the causes of memory strength variability: Recollection, attention failure, or encoding variability?

PubMed Central

Koen, Joshua D.; Aly, Mariam; Wang, Wei-Chun; Yonelinas, Andrew P.

2013-01-01

A prominent finding in recognition memory is that studied items are associated with more variability in memory strength than new items. Here, we test three competing theories for why this occurs - the encoding variability, attention failure, and recollection accounts. Distinguishing amongst these theories is critical because each provides a fundamentally different account of the processes underlying recognition memory. The encoding variability and attention failure accounts propose that old item variance will be unaffected by retrieval manipulations because the processes producing this effect are ascribed to encoding. The recollection account predicts that both encoding and retrieval manipulations that preferentially affect recollection will affect memory variability. These contrasting predictions were tested by examining the effect of response speeding (Experiment 1), dividing attention at retrieval (Experiment 2), context reinstatement (Experiment 3), and increased test delay (Experiment 4) on recognition performance. The results of all four experiments confirmed the predictions of the recollection account, and were inconsistent with the encoding variability account. The evidence supporting the attention failure account was mixed, with two of the four experiments confirming the account and two disconfirming the account. These results indicate that encoding variability and attention failure are insufficient accounts of memory variance, and provide support for the recollection account. Several alternative theoretical accounts of the results are also considered. PMID:23834057

Motivating learning, performance, and persistence: the synergistic effects of intrinsic goal contents and autonomy-supportive contexts.

PubMed

Vansteenkiste, Maarten; Simons, Joke; Lens, Willy; Sheldon, Kennon M; Deci, Edward L

2004-08-01

Three field experiments with high school and college students tested the self-determination theory hypotheses that intrinsic (vs. extrinsic) goals and autonomy-supportive (vs. controlling) learning climates would improve students' learning, performance, and persistence. The learning of text material or physical exercises was framed in terms of intrinsic (community, personal growth, health) versus extrinsic (money, image) goals, which were presented in an autonomy-supportive versus controlling manner. Analyses of variance confirmed that both experimentally manipulated variables yielded main effects on depth of processing, test performance, and persistence (all ps <.001), and an interaction resulted in synergistically high deep processing and test performance (but not persistence) when both intrinsic goals and autonomy support were present. Effects were significantly mediated by autonomous motivation.

Testing of Raman spectroscopy method for assessment of skin implants

NASA Astrophysics Data System (ADS)

Timchenko, E. V.; Timchenko, P. E.; Volova, L. T.; Pershutkina, S. V.; Shalkovskaya, P. Y.

2016-11-01

Results of studies of testing of Raman spectroscopy (RS) method for assessment of skin implants are presented. As objects of study were used samples of rat's skin material. The main spectral differences of implants using various types of their processing appear at wavenumbers 1062 cm-1, 1645 cm-1, 1553 cm-1, 851 cm-1, 863 cm-1, 814 cm-1 and 1410 cm-1. Optical coefficients for assessment of skin implants were introduced. The research results are confirmed by morphological analysis.

A Comprehensive Pitting Study of High Velocity Oxygen Fuel Inconel 625 Coating by Using Electrochemical Testing Techniques

NASA Astrophysics Data System (ADS)

Niaz, Akbar; Khan, Sajid Ullah

2016-01-01

In the present work, Inconel 625 was coated on a mild steel substrate using a high velocity oxygen fuel coating process. The pitting propensity of the coating was tested by using open circuit potential versus time, potentiodynamic polarization, electrochemical potentiokinetic reactivation, and scanning electrochemical microscopy. The pitting propensity of the coating was compared with bulk Inconel 625 alloy. The results confirmed that there were regions of different electrochemical activities on the coating which have caused pitting corrosion.

Use of immuno assays during the development of a Hemophilus influenzae type b vaccine for technology transfer to emerging vaccine manufacturers.

PubMed

Hamidi, Ahd; Kreeftenberg, Hans

2014-01-01

Quality control of Hemophilus Influenzae type b (Hib) conjugate vaccines is mainly dependent on physicochemical methods. Overcoming sample matrix interference when using physicochemical tests is very challenging, these tests are therefore only used to test purified samples of polysaccharide, protein, bulk conjugate, and final product. For successful development of a Hib conjugate vaccine, several ELISA (enzyme-linked immunosorbent assay) methods were needed as an additional tool to enable testing of in process (IP) samples. In this paper, three of the ELISA's that have been very valuable during the process development, implementation and scaling up are highlighted. The PRP-ELISA, was a very efficient tool in testing in process (IP) samples generated during the development of the cultivation and purification process of the Hib-polysaccharide. The antigenicity ELISA, was used to confirm the covalent linkage of PRP and TTd in the conjugate. The anti-PRP IgG ELISA was developed as part of the immunogenicity test, used to demonstrate the ability of the Hib conjugate vaccine to elicit a T-cell dependent immune response in mice. ELISA methods are relatively cheap and easy to implement and therefore very useful during the development of polysaccharide conjugate vaccines.

Quiet Clean Short-haul Experimental Engine (QCSEE). Composite fan frame subsystem test report

NASA Technical Reports Server (NTRS)

Stotler, C. L., Jr.; Bowden, J. H.

1977-01-01

The element and subcomponent testing conducted to verify the composite fan frame design of two experimental high bypass geared turbofan engines and propulsion systems for short haul passenger aircraft is described. Emphasis is placed on the propulsion technology required for future externally blown flap aircraft with engines located both under the wing and over the wing, including technology in composite structures and digital engine controls. The element tests confirmed that the processes used in the frame design would produce the predicted mechanical properties. The subcomponent tests verified that the detail structural components of the frame had adequate structural integrity.

Highly soluble [1]benzothieno[3,2-b]benzothiophene (BTBT) derivatives for high-performance, solution-processed organic field-effect transistors.

PubMed

Ebata, Hideaki; Izawa, Takafumi; Miyazaki, Eigo; Takimiya, Kazuo; Ikeda, Masaaki; Kuwabara, Hirokazu; Yui, Tatsuto

2007-12-26

2,7-Dialkyl[1]benzothieno[3,2-b]benzothiophenes were tested as solution-processible molecular semiconductors. Thin films of the organic semiconductors deposited on Si/SiO2 substrates by spin coating have well-ordered structures as confirmed by XRD analysis. Evaluations of the devices under ambient conditions showed typical p-channel FET responses with the field-effect mobility higher than 1.0 cm2 V-1 s-1 and Ion/Ioff of approximately 10(7).

A Positive Generation Effect on Memory for Auditory Context

PubMed Central

Overman, Amy A.; Richard, Alison G.; Stephens, Joseph D. W.

2016-01-01

Self-generation of information during memory encoding has large positive effects on subsequent memory for items, but mixed effects on memory for contextual information associated with items. A processing account of generation effects on context memory (Mulligan, 2004; Mulligan, Lozito, & Rosner, 2006) proposes that these effects depend on whether the generation task causes any shift in processing of the type of context features for which memory is being tested. Mulligan and colleagues have used this account to predict various negative effects of generation on context memory, but the account also predicts positive generation effects under certain circumstances. The present experiment provided a critical test of the processing account by examining how generation affected memory for auditory rather than visual context. Based on the processing account, we predicted that generation of rhyme words should enhance processing of auditory information associated with the words (i.e., voice gender) whereas generation of antonym words should have no effect. These predictions were confirmed, providing support to the processing account. PMID:27696145

Web-Based Honorarium Confirmation System Prototype

NASA Astrophysics Data System (ADS)

Wisswani, N. W.; Catur Bawa, I. G. N. B.

2018-01-01

Improving services in academic environment can be applied by regulating salary payment process for all employees. As a form of control to maintain financial transparency, employees should have information concerning salary payment process. Currently, notification process of committee honorarium will be accepted by the employees in a manual manner. The salary will be received by the employee bank account and to know its details, they should go to the accounting unit to find out further information. Though there are some employees entering the accounting unit, they still find difficulty to obtain information about detailed honor information that they received in their accounts. This can be caused by many data collected and to be managed. Based on this issue, this research will design a prototype of web-based system for accounting unit system in order to provide detailed financial transaction confirmation to employee bank accounts that have been informed through mobile banking system. This prototype will be developed with Waterfall method through testing on final users after it is developed through PHP program with MySQL as DBMS

Implementation of an Outer Can Welding System for Savannah River Site FB-Line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howard, S.R.

2003-03-27

This paper details three phases of testing to confirm use of a Gas Tungsten Arc (GTA) system for closure welding the 3013 outer container used for stabilization/storage of plutonium metals and oxides. The outer container/lid closure joint was originally designed for laser welding, but for this application, the gas tungsten arc (GTA) welding process has been adapted. The testing progressed in three phases: (1) system checkout to evaluate system components for operational readiness, (2) troubleshooting to evaluate high weld failure rates and develop corrective techniques, and (3) pre-installation acceptance testing.

Investigation of a regulatory agency enquiry into potential porcine circovirus type 1 contamination of the human rotavirus vaccine, Rotarix: approach and outcome.

PubMed

Dubin, Gary; Toussaint, Jean-François; Cassart, Jean-Pol; Howe, Barbara; Boyce, Donna; Friedland, Leonard; Abu-Elyazeed, Remon; Poncelet, Sylviane; Han, Htay Htay; Debrus, Serge

2013-11-01

In January 2010, porcine circovirus type 1 (PCV1) DNA was unexpectedly detected in the oral live-attenuated human rotavirus vaccine, Rotarix (GlaxoSmithKline [GSK] Vaccines) by an academic research team investigating a novel, highly sensitive analysis not routinely used for adventitious agent screening. GSK rapidly initiated an investigation to confirm the source, nature and amount of PCV1 in the vaccine manufacturing process and to assess potential clinical implications of this finding. The investigation also considered the manufacturer's inactivated poliovirus (IPV)-containing vaccines, since poliovirus vaccine strains are propagated using the same cell line as the rotavirus vaccine strain. Results confirmed the presence of PCV1 DNA and low levels of PCV1 viral particles at all stages of the Rotarix manufacturing process. PCV type 2 DNA was not detected at any stage. When tested in human cell lines, productive PCV1 infection was not observed. There was no immunological or clinical evidence of PCV1 infection in infants who had received Rotarix in clinical trials. PCV1 DNA was not detected in the IPV-containing vaccine manufacturing process beyond the purification stage. Retrospective testing confirmed the presence of PCV1 DNA in Rotarix since the initial stages of its development and in vaccine lots used in clinical studies conducted pre- and post-licensure. The acceptable safety profile observed in clinical trials of Rotarix therefore reflects exposure to PCV1 DNA. The investigation into the presence of PCV1 in Rotarix could serve as a model for risk assessment in the event of new technologies identifying adventitious agents in the manufacturing of other vaccines and biological products.

Investigation of a regulatory agency enquiry into potential porcine circovirus type 1 contamination of the human rotavirus vaccine, Rotarix™

PubMed Central

Dubin, Gary; Toussaint, Jean-François; Cassart, Jean-Pol; Howe, Barbara; Boyce, Donna; Friedland, Leonard; Abu-Elyazeed, Remon; Poncelet, Sylviane; Han, Htay Htay; Debrus, Serge

2013-01-01

In January 2010, porcine circovirus type 1 (PCV1) DNA was unexpectedly detected in the oral live-attenuated human rotavirus vaccine, Rotarix™ (GlaxoSmithKline [GSK] Vaccines) by an academic research team investigating a novel, highly sensitive analysis not routinely used for adventitious agent screening. GSK rapidly initiated an investigation to confirm the source, nature and amount of PCV1 in the vaccine manufacturing process and to assess potential clinical implications of this finding. The investigation also considered the manufacturer’s inactivated poliovirus (IPV)-containing vaccines, since poliovirus vaccine strains are propagated using the same cell line as the rotavirus vaccine strain. Results confirmed the presence of PCV1 DNA and low levels of PCV1 viral particles at all stages of the Rotarix™ manufacturing process. PCV type 2 DNA was not detected at any stage. When tested in human cell lines, productive PCV1 infection was not observed. There was no immunological or clinical evidence of PCV1 infection in infants who had received Rotarix™ in clinical trials. PCV1 DNA was not detected in the IPV-containing vaccine manufacturing process beyond the purification stage. Retrospective testing confirmed the presence of PCV1 DNA in Rotarix™ since the initial stages of its development and in vaccine lots used in clinical studies conducted pre- and post-licensure. The acceptable safety profile observed in clinical trials of Rotarix™ therefore reflects exposure to PCV1 DNA. The investigation into the presence of PCV1 in Rotarix™ could serve as a model for risk assessment in the event of new technologies identifying adventitious agents in the manufacturing of other vaccines and biological products. PMID:24056737

Involvement of hippocampal NMDA receptors in encoding and consolidation, but not retrieval, processes of spontaneous object location memory in rats.

PubMed

Yamada, Kazuo; Arai, Misaki; Suenaga, Toshiko; Ichitani, Yukio

2017-07-28

The hippocampus is thought to be involved in object location recognition memory, yet the contribution of hippocampal NMDA receptors to the memory processes, such as encoding, retention and retrieval, is unknown. First, we confirmed that hippocampal infusion of a competitive NMDA receptor antagonist, AP5 (2-amino-5-phosphonopentanoic acid, 20-40nmol), impaired performance of spontaneous object location recognition test but not that of novel object recognition test in Wistar rats. Next, the effects of hippocampal AP5 treatment on each process of object location recognition memory were examined with three different injection times using a 120min delay-interposed test: 15min before the sample phase (Time I), immediately after the sample phase (Time II), and 15min before the test phase (Time III). The blockade of hippocampal NMDA receptors before and immediately after the sample phase, but not before the test phase, markedly impaired performance of object location recognition test, suggesting that hippocampal NMDA receptors play an important role in encoding and consolidation/retention, but not retrieval, of spontaneous object location memory. Copyright © 2017 Elsevier B.V. All rights reserved.

Auditory Middle Latency Response and Phonological Awareness in Students with Learning Disabilities

PubMed Central

Romero, Ana Carla Leite; Funayama, Carolina Araújo Rodrigues; Capellini, Simone Aparecida; Frizzo, Ana Claudia Figueiredo

2015-01-01

Introduction Behavioral tests of auditory processing have been applied in schools and highlight the association between phonological awareness abilities and auditory processing, confirming that low performance on phonological awareness tests may be due to low performance on auditory processing tests. Objective To characterize the auditory middle latency response and the phonological awareness tests and to investigate correlations between responses in a group of children with learning disorders. Methods The study included 25 students with learning disabilities. Phonological awareness and auditory middle latency response were tested with electrodes placed on the left and right hemispheres. The correlation between the measurements was performed using the Spearman rank correlation coefficient. Results There is some correlation between the tests, especially between the Pa component and syllabic awareness, where moderate negative correlation is observed. Conclusion In this study, when phonological awareness subtests were performed, specifically phonemic awareness, the students showed a low score for the age group, although for the objective examination, prolonged Pa latency in the contralateral via was observed. Negative weak to moderate correlation for Pa wave latency was observed, as was positive weak correlation for Na-Pa amplitude. PMID:26491479

Psychometric evaluation of the Swedish adaptation of the Inventory for Assessing the Process of Cultural Competence Among Healthcare Professionals--Revised (IAPCC-R).

PubMed

Olt, Helen; Jirwe, Maria; Gustavsson, Petter; Emami, Azita

2010-01-01

The purpose of this study was to describe the translation, adaption, and psychometric evaluation process in relation to validity and reliability of the Swedish version of the instrument, Inventory for Assessing The Process of Cultural Competence Among Healthcare Professionals-Revised (IAPCC-R) following the translation, adaptation, and psychometric evaluation process. Validity tests were conducted on the response processes (N = 15), the content (N = 7), and the internal structure of the instrument (N = 334). Reliability (alpha = .65 for the total scale varying between -.01 and .65 for the different subscales) was evaluated in terms of internal consistency. Results indicated weak validity and reliability though it is difficult to conclude whether this is related to adaptation issues or the original construction.The testing of the response process identified problems in relation to respondents' conceptualization of cultural competence. The test of the content identified a weak correspondence between the items and the underlying model. In addition, a confirmatory factor analysis did not confirm the proposed structure of the instrument. This study concludes that this instrument is not valid and reliable for use with a Swedish population of practicing nurses or nursing students.

Validation of the Vanderbilt Holistic Face Processing Test.

PubMed

Wang, Chao-Chih; Ross, David A; Gauthier, Isabel; Richler, Jennifer J

2016-01-01

The Vanderbilt Holistic Face Processing Test (VHPT-F) is a new measure of holistic face processing with better psychometric properties relative to prior measures developed for group studies (Richler et al., 2014). In fields where psychologists study individual differences, validation studies are commonplace and the concurrent validity of a new measure is established by comparing it to an older measure with established validity. We follow this approach and test whether the VHPT-F measures the same construct as the composite task, which is group-based measure at the center of the large literature on holistic face processing. In Experiment 1, we found a significant correlation between holistic processing measured in the VHPT-F and the composite task. Although this correlation was small, it was comparable to the correlation between holistic processing measured in the composite task with the same faces, but different target parts (top or bottom), which represents a reasonable upper limit for correlations between the composite task and another measure of holistic processing. These results confirm the validity of the VHPT-F by demonstrating shared variance with another measure of holistic processing based on the same operational definition. These results were replicated in Experiment 2, but only when the demographic profile of our sample matched that of Experiment 1.

Validation of the Vanderbilt Holistic Face Processing Test

PubMed Central

Wang, Chao-Chih; Ross, David A.; Gauthier, Isabel; Richler, Jennifer J.

2016-01-01

The Vanderbilt Holistic Face Processing Test (VHPT-F) is a new measure of holistic face processing with better psychometric properties relative to prior measures developed for group studies (Richler et al., 2014). In fields where psychologists study individual differences, validation studies are commonplace and the concurrent validity of a new measure is established by comparing it to an older measure with established validity. We follow this approach and test whether the VHPT-F measures the same construct as the composite task, which is group-based measure at the center of the large literature on holistic face processing. In Experiment 1, we found a significant correlation between holistic processing measured in the VHPT-F and the composite task. Although this correlation was small, it was comparable to the correlation between holistic processing measured in the composite task with the same faces, but different target parts (top or bottom), which represents a reasonable upper limit for correlations between the composite task and another measure of holistic processing. These results confirm the validity of the VHPT-F by demonstrating shared variance with another measure of holistic processing based on the same operational definition. These results were replicated in Experiment 2, but only when the demographic profile of our sample matched that of Experiment 1. PMID:27933014

Perceived time slows during fleeting fun or fear.

PubMed

Corke, Mike; Bell, Jason; Goodhew, Stephanie C; Smithson, Michael; Edwards, Mark

2018-02-01

Previous psychophysical studies at durations greater than 1000 ms have confirmed the anecdotal reports of an increase in the perceived duration of both positively and negatively valenced emotive stimuli; however, the results of studies at durations less than 1000 ms have been inconsistent. This study further investigated the effect of valence on the perception of durations less than 1000 ms. We used both positively and negatively valenced stimuli in order to compare their effects on the distortion of duration, and we tested multiple data points within the sub-one-second range. We found an increase in the perceived duration of both positively and negatively valenced emotional stimuli at all data points. This is consistent with studies at durations longer than 1000 ms and also with models of temporal processing. We also confirmed that Weber fractions, within the range tested, followed the generalized form of Weber's law.

Spatial and temporal distribution of rabies in northern Tanzania in the period of 1993-2002.

PubMed

Swai, E S; Moshy, W E; Kaaya, J E; Mtui, P F

2010-01-01

A retrospective study was carried out to investigate the occurrence and distribution patterns of rabies cases in northern Tanzania. Data on laboratory confirmed brain samples and associated case reports submitted to the Arusha Veterinary Investigation Centre, for a period of ten years (1993-2002) was retrieved and reviewed. A total of 98 suspected rabies brain specimens from different animal species and geographical areas were submitted and processed during the period under review. Rabies was confirmed using Fluorescent Antibody Technique test. Of the 98 brain specimens processed, 65 (66.3%) were confirmed to be rabies cases. Canine rabies accounted for 73.8% of the cases and was diagnosed in dogs (43), jackals (4) and hyenas (1). Rabies in wildlife accounted for 5 out of 48 canine confirmed cases. Most of the cases were from Arusha Municipality (20) followed by Arumeru (19), Ngorongoro (9) and Moshi (8) districts. Rabies positive cases in other animal species were in the following order of frequencies: bovine (9 out of 11); feline (5 out of 10); equine (1 out of 2); caprine (2 out of 2). One porcine brain specimen was rabies negative. The high proportion of rabies positive cases confirmed suggests the level of their endemicity in the northern regions of Tanzania. Moreover, the findings highlights the need for sustained surveillance and institution of control measures among dog population and awareness creation particularly among general public and children whom are at high risk of contracting rabies because of their close contact with dogs.

16 CFR 1633.5 - Prototype pooling and confirmation testing requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Prototype pooling and confirmation testing... Prototype pooling and confirmation testing requirements. (a) Prototype pooling. One or more manufacturers may rely on a qualified prototype produced by another manufacturer or prototype developer provided...

Machining of Aircraft Titanium with Abrasive-Waterjets for Fatigue Critical Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, H. T.; Hovanski, Yuri; Dahl, Michael E.

2012-02-01

Laboratory tests were conducted to determine the fatigue performance of abrasive-waterjet- (AWJ-) machined aircraft titanium. Dog-bone specimens machined with AWJs were prepared and tested with and without sanding and dry-grit blasting with Al2O3 as secondary processes. The secondary processes were applied to remove the visual appearance of AWJ-generated striations and to clean up the garnet embedment. The fatigue performance of AWJ-machined specimens was compared with baseline specimens machined with CNC milling. Fatigue test results of the titanium specimens not only confirmed our previous findings in aluminum dog-bone specimens but in comparison also further enhanced the fatigue performance of the titanium.more » In addition, titanium is known to be difficult to cut, particularly for thick parts, however AWJs cut the material 34% faster han stainless steel. AWJ cutting and dry-grit blasting are shown to be a preferred ombination for processing aircraft titanium that is fatigue critical.« less

Noise model for low-frequency through-the-Earth communication

NASA Astrophysics Data System (ADS)

Raab, Frederick H.

2010-12-01

Analysis and simulation of through-the-Earth communication links and signal processing techniques require a more complete noise model than is needed for the analysis of conventional communication systems. This paper presents a multicomponent noise model that includes impulsive characteristics, direction-of-arrival characteristics, and effects of local geology. The noise model is derived from theoretical considerations and confirmed by field tests.

An investigation on die crack detection using Temperature Sensitive Parameter for high speed LED mass production

NASA Astrophysics Data System (ADS)

Annaniah, Luruthudass; Devarajan, Mutharasu; San, Teoh Kok

To ensure the highest quality & long-term reliability of LED components it is necessary to examine LED dice that have sustained mechanical damage during the manufacturing process. This paper has demonstrated that detection of die crack in mass manufactured LEDs can be achieved by measuring Temperature Sensitive Parameters (TSPs) during final testing. A newly-designed apparatus and microcontroller was used for this investigation in order to achieve the millisecond switching time needed for detecting thermal transient effects and at the same time meet the expected speed for mass manufacturing. Evaluations conducted at lab scale shows that thermal transient behaviour of cracked die is significantly different than that of an undamaged die. Having an established test limits to differentiate cracked dice, large volume tests in a production environment were used to confirm the effectiveness of this test method. Failure Bin Analysis (FBA) of this high volume experiment confirmed that all the cracked die LEDs were detected and the undamaged LEDs passed this test without over-rejection. The work verifies that tests based on TSP are effective in identifying die cracks and it is believed that the method could be extended to other types of rejects that have thermal transient signatures such as die delamination.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, workers confirm the Multi-Purpose Logistics Module Donatello is safely in place on a work stand. Previously housed in the Operations and Checkout Building, Donatello was brought into the SSPF for routine testing. This is the first time all three MPLMs (Donatello, Raffaello and Leonardo) are in the SSPF. The MPLMs were built by the Italian Space Agency, to serve as reusable logistics carriers and the primary delivery system to resupply and return station cargo requiring a pressurized environment. The third MPLM, Raffaello, is scheduled to fly on Space Shuttle Atlantis on mission STS-114.

NASA Image and Video Library

2004-02-13

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, workers confirm the Multi-Purpose Logistics Module Donatello is safely in place on a work stand. Previously housed in the Operations and Checkout Building, Donatello was brought into the SSPF for routine testing. This is the first time all three MPLMs (Donatello, Raffaello and Leonardo) are in the SSPF. The MPLMs were built by the Italian Space Agency, to serve as reusable logistics carriers and the primary delivery system to resupply and return station cargo requiring a pressurized environment. The third MPLM, Raffaello, is scheduled to fly on Space Shuttle Atlantis on mission STS-114.

Hypothermic general cold adaptation induced by local cold acclimation.

PubMed

Savourey, G; Barnavol, B; Caravel, J P; Feuerstein, C; Bittel, J H

1996-01-01

To study relationships between local cold adaptation of the lower limbs and general cold adaptation, eight subjects were submitted both to a cold foot test (CFT, 5 degrees C water immersion, 5 min) and to a whole-body standard cold air test (SCAT, 1 degree C, 2 h, nude at rest) before and after a local cold acclimation (LCA) of the lower limbs effected by repeated cold water immersions. The LCA induced a local cold adaptation confirmed by higher skin temperatures of the lower limbs during CFT and a hypothermic insulative general cold adaptation (decreased rectal temperature and mean skin temperature P < 0.05) without a change either in metabolic heat production or in lower limb skin temperatures during SCAT after LCA. It was concluded that local cold adaptation was related to the habituation process confirmed by decreased plasma concentrations of noradrenaline (NA) during LCA (P < 0.05). However, the hypothermic insulative general cold adaptation was unrelated either to local cold adaptation or to the habituation process, because an increased NA during SCAT after LCA (P < 0.05) was observed but was rather related to a "T3 polar syndrome" occurring during LCA.

Screening of trace elements in hair of the female population with different types of cancers in Wielkopolska region of Poland.

PubMed

Czerny, Bogusław; Krupka, Krzysztof; Ożarowski, Marcin; Seremak-Mrozikiewicz, Agnieszka

2014-01-01

Cancer constitutes a major health problem worldwide. Thus, search for reliable and practical markers of the disease process remains the key issue of the diagnostic process. The study aims at linking the trace element status of an organism, assessed by hair analysis, with the occurrence of cancer diseases. Hair samples were collected from 299 patients with cancer diseases confirmed by a histopathological test and from 100 controls. Cancer patients were divided into three groups, depending on cancer type: hormone-dependent cancer, cancer of the alimentary tract, and cancer with high glycolytic activity. Mineral element analysis of hair was performed using an atomic emission spectrophotometer with inductively coupled plasma (ICP-OES) and inductively coupled plasma mass spectrometry (ICP-MS). Statistically significantly lower concentrations of selenium, zinc, copper, germanium and boron, iron, and magnesium were observed in the three groups of cancer patients. Disturbance in the axis glucose-insulin and changes in concentrations of heavy metals and toxic elements were also noted. It seems safe to conclude that our results confirmed usefulness of hair element analysis in screening tests for the assessment of the biomarker of various cancer diseases in a female population.

Confirming nasogastric tube placement: Is the colorimeter as sensitive and specific as X-ray? A diagnostic accuracy study.

PubMed

Mordiffi, Siti Zubaidah; Goh, Mien Li; Phua, Jason; Chan, Yiong-Huak

2016-09-01

The effect of delivering enteral nutrition or medications via a nasogastric tube that is inadvertently located in the tracheobronchial tract can cause respiratory complications. Although radiographic examination is accepted as the gold standard for confirming the position of patients' enteral tubes, it is costly, involves risks of radiation, and is not failsafe. Studies using carbon dioxide sensors to detect inadvertent nasogastric tube placements have been conducted in intensive care settings. However, none involved patients in general wards. The objective of this study was to ascertain the diagnostic measure of colorimeter, with radiographic examination as the reference standard, to confirm the location of nasogastric tubes in patients. A prospective observational study of a diagnostic test. This study was conducted in the general wards of an approximately 1100-bed acute care tertiary hospital of an Academic Medical Center in Singapore. Adult patients with nasogastric tubes admitted to the general wards were recruited into the study. The colorimeter was attached to the nasogastric tube to detect for the presence of carbon dioxide, suggestive of a tracheobronchial placement. The exact location of the nasogastric tube was subsequently confirmed by a radiographic examination. A total of 192 tests were undertaken. The colorimeter detected carbon dioxide in 29 tested nasogastric tubes, of which radiographic examination confirmed that four tubes were located in the tracheobronchial tract. The colorimeter failed to detect carbon dioxide in one nasogastric tube that was located in the tracheobronchial tract, thus, demonstrating a sensitivity of 0.80 [95% CI (0.376, 0.964)]. The colorimeter detected absence of carbon dioxide in 163 tested nasogastric tubes in which radiographic examination confirmed 160 gastrointestinal and one tracheobronchial placements, demonstrating a specificity of 0.865 [95% CI (0.808, 0.907)]. The colorimeter detected one tracheobronchial nasogastric tube placement that the radiographic examination was misinterpreted. The study found that the use of the colorimeter in the general ward setting was not 100% sensitive or specific in ascertaining the location of a nasogastric tube as previously reported by many studies undertaken in intensive care settings. This is the first study on the use of a colorimeter to confirm the placement of a nasogastric tube in adult patients in the general ward setting. More research on the use of a colorimeter in the general ward setting and its potential use in certain processes for confirming the placement of a nasogastric tube is warranted. Copyright © 2016 Elsevier Ltd. All rights reserved.

MICROBIAL CONTAMINATION OF STREET VENDED FOODS FROM A UNIVERSITY CAMPUS IN BANGLADESH.

PubMed

Islam, Sufia; Nasrin, Nishat; Rizwan, Farhana; Nahar, Lutfun; Bhowmik, Adity; Esha, Sayma Afrin; Talukder, Kaisar Ali; Akter, Mahmuda; Roy, Ajoy; Ahmed, Muniruddin

2015-05-01

The microbiological quality of street vended food samples from Dhaka, Bangladesh was evaluated. The objective of the study was to identify the presence of common pathogens (Escherichia coli, Shigella spp, Salmonella and Vibrio spp) and to describe the molecular characterization of E coli, a commonly found pathogen in various street foods. Fifty food samples were collected from fixed and mobile vendors from two sampling locations (Mohakhali and Aftabnagar) in Dhaka city, Bangladesh. The tested samples included deep fried and fried snacks; quick lunch items; pickles; fruit chutney; baked items; spicy, sour and hot snacks etc: Juices, tamarind water and plain drinking water were also tested. Sterile polythene bags were used for collecting 200 g of each category of samples. They were tested for the presence of microorganisms following conventional microbiological processes. Biochemical tests followed by serology were done for the confirmation of Shigella and Salmonella. Serological reaction was carried out for confirmation of Vibrio spp. DNA was isolated for the molecular characterization to detect the pathogenic E. coli by polymerase chain reaction (PCR). Out of 50 food samples, six (12%) were confirmed to contain different species of E. coli and Shigella. Molecular characterization of E. coli revealed that three samples were contaminated with enteroaggregative E. coli (EAEC) and one was contaminated with enterotoxigenic E. coli (ETEC). Shigellaflexneri X variant was detected in one food item and Shigella flexneri 2a was found in drinking water. All these enteric pathogens could be the potential cause for foodborne illnesses.

Low visual information-processing speed and attention are predictors of fatigue in elementary and junior high school students

PubMed Central

2011-01-01

Background Fatigue is a common complaint among elementary and junior high school students, and is known to be associated with reduced academic performance. Recently, we demonstrated that fatigue was correlated with decreased cognitive function in these students. However, no studies have identified cognitive predictors of fatigue. Therefore, we attempted to determine independent cognitive predictors of fatigue in these students. Methods We performed a prospective cohort study. One hundred and forty-two elementary and junior high school students without fatigue participated. They completed a variety of paper-and-pencil tests, including list learning and list recall tests, kana pick-out test, semantic fluency test, figure copying test, digit span forward test, and symbol digit modalities test. The participants also completed computerized cognitive tests (tasks A to E on the modified advanced trail making test). These cognitive tests were used to evaluate motor- and information-processing speed, immediate and delayed memory function, auditory and visual attention, divided and switching attention, retrieval of learned material, and spatial construction. One year after the tests, a questionnaire about fatigue (Japanese version of the Chalder Fatigue Scale) was administered to all the participants. Results After the follow-up period, we confirmed 40 cases of fatigue among 118 students. In multivariate logistic regression analyses adjusted for grades and gender, poorer performance on visual information-processing speed and attention tasks was associated with increased risk of fatigue. Conclusions Reduced visual information-processing speed and poor attention are independent predictors of fatigue in elementary and junior high school students. PMID:21672212

Low visual information-processing speed and attention are predictors of fatigue in elementary and junior high school students.

PubMed

Mizuno, Kei; Tanaka, Masaaki; Fukuda, Sanae; Yamano, Emi; Shigihara, Yoshihito; Imai-Matsumura, Kyoko; Watanabe, Yasuyoshi

2011-06-14

Fatigue is a common complaint among elementary and junior high school students, and is known to be associated with reduced academic performance. Recently, we demonstrated that fatigue was correlated with decreased cognitive function in these students. However, no studies have identified cognitive predictors of fatigue. Therefore, we attempted to determine independent cognitive predictors of fatigue in these students. We performed a prospective cohort study. One hundred and forty-two elementary and junior high school students without fatigue participated. They completed a variety of paper-and-pencil tests, including list learning and list recall tests, kana pick-out test, semantic fluency test, figure copying test, digit span forward test, and symbol digit modalities test. The participants also completed computerized cognitive tests (tasks A to E on the modified advanced trail making test). These cognitive tests were used to evaluate motor- and information-processing speed, immediate and delayed memory function, auditory and visual attention, divided and switching attention, retrieval of learned material, and spatial construction. One year after the tests, a questionnaire about fatigue (Japanese version of the Chalder Fatigue Scale) was administered to all the participants. After the follow-up period, we confirmed 40 cases of fatigue among 118 students. In multivariate logistic regression analyses adjusted for grades and gender, poorer performance on visual information-processing speed and attention tasks was associated with increased risk of fatigue. Reduced visual information-processing speed and poor attention are independent predictors of fatigue in elementary and junior high school students. © 2011 Mizuno et al; licensee BioMed Central Ltd.

Examining the causes of memory strength variability: recollection, attention failure, or encoding variability?

PubMed

Koen, Joshua D; Aly, Mariam; Wang, Wei-Chun; Yonelinas, Andrew P

2013-11-01

A prominent finding in recognition memory is that studied items are associated with more variability in memory strength than new items. Here, we test 3 competing theories for why this occurs-the encoding variability, attention failure, and recollection accounts. Distinguishing among these theories is critical because each provides a fundamentally different account of the processes underlying recognition memory. The encoding variability and attention failure accounts propose that old item variance will be unaffected by retrieval manipulations because the processes producing this effect are ascribed to encoding. The recollection account predicts that both encoding and retrieval manipulations that preferentially affect recollection will affect memory variability. These contrasting predictions were tested by examining the effect of response speeding (Experiment 1), dividing attention at retrieval (Experiment 2), context reinstatement (Experiment 3), and increased test delay (Experiment 4) on recognition performance. The results of all 4 experiments confirm the predictions of the recollection account and are inconsistent with the encoding variability account. The evidence supporting the attention failure account is mixed, with 2 of the 4 experiments confirming the account and 2 disconfirming the account. These results indicate that encoding variability and attention failure are insufficient accounts of memory variance and provide support for the recollection account. Several alternative theoretical accounts of the results are also considered. PsycINFO Database Record (c) 2013 APA, all rights reserved.

About-face on face recognition ability and holistic processing

PubMed Central

Richler, Jennifer J.; Floyd, R. Jackie; Gauthier, Isabel

2015-01-01

Previous work found a small but significant relationship between holistic processing measured with the composite task and face recognition ability measured by the Cambridge Face Memory Test (CFMT; Duchaine & Nakayama, 2006). Surprisingly, recent work using a different measure of holistic processing (Vanderbilt Holistic Face Processing Test [VHPT-F]; Richler, Floyd, & Gauthier, 2014) and a larger sample found no evidence for such a relationship. In Experiment 1 we replicate this unexpected result, finding no relationship between holistic processing (VHPT-F) and face recognition ability (CFMT). A key difference between the VHPT-F and other holistic processing measures is that unique face parts are used on each trial in the VHPT-F, unlike in other tasks where a small set of face parts repeat across the experiment. In Experiment 2, we test the hypothesis that correlations between the CFMT and holistic processing tasks are driven by stimulus repetition that allows for learning during the composite task. Consistent with our predictions, CFMT performance was correlated with holistic processing in the composite task when a small set of face parts repeated over trials, but not when face parts did not repeat. A meta-analysis confirms that relationships between the CFMT and holistic processing depend on stimulus repetition. These results raise important questions about what is being measured by the CFMT, and challenge current assumptions about why faces are processed holistically. PMID:26223027

About-face on face recognition ability and holistic processing.

PubMed

Richler, Jennifer J; Floyd, R Jackie; Gauthier, Isabel

2015-01-01

Previous work found a small but significant relationship between holistic processing measured with the composite task and face recognition ability measured by the Cambridge Face Memory Test (CFMT; Duchaine & Nakayama, 2006). Surprisingly, recent work using a different measure of holistic processing (Vanderbilt Holistic Face Processing Test [VHPT-F]; Richler, Floyd, & Gauthier, 2014) and a larger sample found no evidence for such a relationship. In Experiment 1 we replicate this unexpected result, finding no relationship between holistic processing (VHPT-F) and face recognition ability (CFMT). A key difference between the VHPT-F and other holistic processing measures is that unique face parts are used on each trial in the VHPT-F, unlike in other tasks where a small set of face parts repeat across the experiment. In Experiment 2, we test the hypothesis that correlations between the CFMT and holistic processing tasks are driven by stimulus repetition that allows for learning during the composite task. Consistent with our predictions, CFMT performance was correlated with holistic processing in the composite task when a small set of face parts repeated over trials, but not when face parts did not repeat. A meta-analysis confirms that relationships between the CFMT and holistic processing depend on stimulus repetition. These results raise important questions about what is being measured by the CFMT, and challenge current assumptions about why faces are processed holistically.

Evidence for Trait Related Theory of Mind Impairment in First Episode Psychosis Patients and Its Relationship with Processing Speed: A 3 Year Follow-up Study.

PubMed

Ayesa-Arriola, Rosa; Setién-Suero, Esther; Neergaard, Karl D; Ferro, Adele; Fatjó-Vilas, Mar; Ríos-Lago, Marcos; Otero, Soraya; Rodríguez-Sánchez, Jose M; Crespo-Facorro, Benedicto

2016-01-01

This study aimed to confirm whether first-episode psychosis patients present a stable trait impairment in theory of mind (ToM) and to examine the potential relationship between ToM and clinical symptomatology and neurocognition. Patients with a first episode of psychosis (N = 160) and healthy controls (N = 159) were assessed with an extensive neuropsychological test battery, which included a mental state decoding task known as "The Reading the Mind in the Eyes" (Eyes test), at baseline and reassessed after 1 and 3 years. The clinical group performed below healthy controls on the Eyes test while not showing test-retest differences between baseline and follow-up administrations. Analyses revealed age, education and premorbid IQ as potential moderators. Poorer performance on the Eyes test was not linked to clinical symptomatology but was associated with greater neurocognitive deficit, particularly related to processing speed. The persistence of ToM deficits in patients suggests that there are trait related metalizing impairments in first episode psychosis. This study shows the influence of processing speed and moderator variables on efficient ToM.

Evidence for Trait Related Theory of Mind Impairment in First Episode Psychosis Patients and Its Relationship with Processing Speed: A 3 Year Follow-up Study

PubMed Central

Ayesa-Arriola, Rosa; Setién-Suero, Esther; Neergaard, Karl D.; Ferro, Adele; Fatjó-Vilas, Mar; Ríos-Lago, Marcos; Otero, Soraya; Rodríguez-Sánchez, Jose M.; Crespo-Facorro, Benedicto

2016-01-01

This study aimed to confirm whether first-episode psychosis patients present a stable trait impairment in theory of mind (ToM) and to examine the potential relationship between ToM and clinical symptomatology and neurocognition. Patients with a first episode of psychosis (N = 160) and healthy controls (N = 159) were assessed with an extensive neuropsychological test battery, which included a mental state decoding task known as “The Reading the Mind in the Eyes” (Eyes test), at baseline and reassessed after 1 and 3 years. The clinical group performed below healthy controls on the Eyes test while not showing test-retest differences between baseline and follow-up administrations. Analyses revealed age, education and premorbid IQ as potential moderators. Poorer performance on the Eyes test was not linked to clinical symptomatology but was associated with greater neurocognitive deficit, particularly related to processing speed. The persistence of ToM deficits in patients suggests that there are trait related metalizing impairments in first episode psychosis. This study shows the influence of processing speed and moderator variables on efficient ToM. PMID:27199826

A study on recovery of uranium in the anode basket residues delivered from the pyrochemical process of used nuclear fuel

NASA Astrophysics Data System (ADS)

Eun, H. C.; Kim, T. J.; Jang, J. H.; Kim, G. Y.; Park, S. B.; Yoon, D. S.; Kim, S. H.; Paek, S. W.; Lee, S. J.

2018-04-01

In this study, the chlorination of uranium oxide (UO2) using ammonium chloride and zirconium as chemical agents was conducted to recover the uranium in the anode basket residues from the pyrochemical process of used nuclear fuel. The chlorination of UO2 was predicted using thermodynamic equilibrium calculations. The experimental conditions for the chlorination were determined using a chlorination test with cerium oxide (CeO2). In the chlorination test, it was confirmed that UO2 was chlorinated into UCl3 at 320 °C, some UO2 remained without changes in the chemical form, and ZrO2, Zr2O, and ZrCl2 were generated as byproducts.

Cognitive and neuropathologic correlates of Stroop Color-Word Test performance in Alzheimer's disease.

PubMed

Bondi, Mark W; Serody, Adam B; Chan, Agnes S; Eberson-Shumate, Sonja C; Delis, Dean C; Hansen, Lawrence A; Salmon, David P

2002-07-01

The Stroop Color-Word Test (SCWT; C. Golden, 1978) was examined in 59 patients with probable Alzheimer's disease (AD) and in 51 demographically comparable normal control (NC) participants. AD patients produced significantly larger Stroop interference effects than NC participants, and level of dementia severity significantly influenced SCWT performance. Principal-components analyses demonstrated a dissociation in the factor structure of the Stroop trials between NC participants and AD patients, suggesting that disruption of semantic knowledge and speeded verbal processing in AD may be a major contributor to impairment on the incongruent trial. Results of clinicopathologic correlations in an autopsy-confirmed AD subgroup further suggest the invocation of a broad network of integrated cortical regions and executive and language processes underlying successful SCWT performance.

Measuring the Processes of Change From the Transtheoretical Model for Physical Activity and Exercise in Overweight and Obese Adults.

PubMed

Romain, Ahmed Jerôme; Bernard, Paquito; Hokayem, Marie; Gernigon, Christophe; Avignon, Antoine

2016-03-01

This study aimed to test three factorial structures conceptualizing the processes of change (POC) from the transtheoretical model and to examine the relationships between the POC and stages of change (SOC) among overweight and obese adults. Cross-sectional study. This study was conducted at the University Hospital of Montpellier, France. A sample of 289 overweight or obese participants (199 women) was enrolled in the study. Participants completed the POC and SOC questionnaires during a 5-day hospitalization for weight management. Structural equation modeling was used to compare the different factorial structures. The unweighted least-squares method was used to identify the best-fit indices for the five fully correlated model (goodness-of-fit statistic = .96; adjusted goodness-of-fit statistic = .95; standardized root mean residual = .062; normed-fit index = .95; parsimonious normed-fit index = .83; parsimonious goodness-of-fit statistic = .78). The multivariate analysis of variance was significant (p < .001). A post hoc test showed that individuals in advanced SOC used more of both experiential and behavioral POC than those in preaction stages, with effect sizes ranging from .06 to .29. This study supports the validity of the factorial structure of POC concerning physical activity and confirms the assumption that, in this context, people with excess weight use both experiential and behavioral processes. These preliminary results should be confirmed in a longitudinal study. © The Author(s) 2016.

Design and Assessment of Online, Interactive Tutorials That Teach Science Process Skills.

PubMed

Kramer, Maxwell; Olson, Dalay; Walker, J D

2018-06-01

Explicit emphasis on teaching science process skills leads to both gains in the skills themselves and, strikingly, deeper understanding of content. Here, we created and tested a series of online, interactive tutorials with the goal of helping undergraduate students develop science process skills. We designed the tutorials in accordance with evidence-based multimedia design principles and student feedback from usability testing. We then tested the efficacy of the tutorials in an introductory undergraduate biology class. On the basis of a multivariate ordinary least-squares regression model, students who received the tutorials are predicted to score 0.82 points higher on a 15-point science process skill assessment than their peers who received traditional textbook instruction on the same topic. This moderate but significant impact indicates that well-designed online tutorials can be more effective than traditional ways of teaching science process skills to undergraduate students. We also found trends that suggest the tutorials are especially effective for nonnative English-speaking students. However, due to a limited sample size, we were unable to confirm that these trends occurred due to more than just variation in the student group sampled.

Design and Manufacturing of Composite Tower Structure for Wind Turbine Equipment

NASA Astrophysics Data System (ADS)

Park, Hyunbum

2018-02-01

This study proposes the composite tower design process for large wind turbine equipment. In this work, structural design of tower and analysis using finite element method was performed. After structural design, prototype blade manufacturing and test was performed. The used material is a glass fiber and epoxy resin composite. And also, sand was used in the middle part. The optimized structural design and analysis was performed. The parameter for optimized structural design is weight reduction and safety of structure. Finally, structure of tower will be confirmed by structural test.

Rational development of solid dispersions via hot-melt extrusion using screening, material characterization, and numeric simulation tools.

PubMed

Zecevic, Damir E; Wagner, Karl G

2013-07-01

Effective and predictive small-scale selection tools are inevitable during the development of a solubility enhanced drug product. For hot-melt extrusion, this selection process can start with a microscale performance evaluation on a hot-stage microscope (HSM). A batch size of 400 mg can provide sufficient materials to assess the drug product attributes such as solid-state properties, solubility enhancement, and physical stability as well as process related attributes such as processing temperature in a twin-screw extruder (TSE). Prototype formulations will then be fed into a 5 mm TSE (~1-2 g) to confirm performance from the HSM under additional shear stress. Small stress stability testing might be performed with these samples or a larger batch (20-40 g) made by 9 or 12 mm TSE. Simultaneously, numeric process simulations are performed using process data as well as rheological and thermal properties of the formulations. Further scale up work to 16 and 18 mm TSE confirmed and refined the simulation model. Thus, at the end of the laboratory-scale development, not only the clinical trial supply could be manufactured, but also one can form a sound risk assessment to support further scale up even without decades of process experience. Copyright © 2013 Wiley Periodicals, Inc.

Comparing Tests for Diabetes and Prediabetes: A Quick Reference Guide

MedlinePlus

... Urinary Tract Imaging Urodynamic Testing Virtual Colonoscopy Diabetes & Prediabetes Tests This fact sheet compares the following tests: ... test Confirming Diagnosis of Type 2 Diabetes and Prediabetes Diagnosis must be confirmed unless symptoms are present. ...

Retrospective study of urinalysis for dl-amphetamine and dl-methamphetamine analysis under current Department of Defense guidelines.

PubMed

Shippee, R L; Kippenberger, D J

2000-09-01

Under current Department of Defense (DOD) directive, the laboratories certified to conduct urinalyis testing in support of the DOD Drug Deterrence Program are required to conduct dl-isomer analysis on all specimens that confirm at a concentration greater than 500 ng/mL methamphetamine (METH). Although the same cutoff concentration is required for amphetamine (AMP) reporting, there is no requirement for dl-isomer analysis of AMP-positive specimens. Of the 894,823 specimens screened by the Army Drug Testing Laboratory at Ft. Meade, MD during a 19-month period, 339 confirmed positive for METH. From this positive population, seven specimens failed to confirm at or above the DOD cutoff of > 20% d-isomer. One of the seven specimens contained 534 ng/mL l-AMP and was reported positive for AMP. Although 100% of the AMP was the l-isomer, under current DOD directive, this information was not passed along to the Medical Review Officers (MRO) to assist them during the interview process. Although this situation appears to be a rare event, consideration should be given to requiring dl-isomer analysis of AMP-positive specimens and forwarding this information to the MRO.

Bovine tuberculosis in Northern Ireland: quantification of the population disease-level effect from cattle leaving herds detected as a source of infection.

PubMed

Doyle, L P; Courcier, E A; Gordon, A W; O'Hagan, M J H; Stegeman, J A; Menzies, F D

2017-12-01

Determination of the proportion of bovine tuberculosis (bTB) breakdowns attributed to a herd purchasing infected animals has not been previously quantified using data from the Animal and Public Health Information System (APHIS) database in Northern Ireland. We used a case-control study design to account for the infection process occurring in the disclosing bTB breakdown herds. Cases (N = 6926) were cattle moving to a future confirmed bTB breakdown where they would disclose as a confirmed bTB reactor or a Lesion at Routine Slaughter (LRS). Controls (N = 303 499) were cattle moving to a future confirmed bTB breakdown where they did not become a bTB reactor or LRS. Our study showed that the cattle leaving herds which disclosed bTB within 450 days had an increased odds of becoming a confirmed bTB reactor or LRS compared with the cattle which left herds that remained free for 450 days (odds ratio (OR) = 2·09: 95% CI 1·96-2·22). Of the 12 060 confirmed bTB breakdowns included in our study (2007-2015 inclusive), 31% (95% CI 29·8-31·5) contained a confirmed bTB reactor(s) or LRS(s) at the disclosing test which entered the herd within the previous 450 days. After controlling for the infection process occurring in the disclosing bTB breakdown herd, our study showed that 6·4% (95% CI 5·9-6·8) of bTB breakdowns in Northern Ireland were directly attributable to the movement of infected animals.

Cochlin-tomoprotein (CTP) detection test identified perilymph leakage preoperatively in revision stapes surgery.

PubMed

Kataoka, Yuko; Ikezono, Tetsuo; Fukushima, Kunihiro; Yuen, Koji; Maeda, Yukihide; Sugaya, Akiko; Nishizaki, Kazunori

2013-08-01

Perilymphatic fistula (PLF) is defined as an abnormal leakage between perilymph from the labyrinth to the middle ear. Symptoms include hearing loss, tinnitus, and vertigo. The standard mode of PLF detection is intraoperative visualization of perilymph leakage and fistula, which ostensibly confirms the existence of PLF. Other possible methods of diagnosis include confirmation of pneumolabyrinth via diagnostic imaging. Recently, a cochlin-tomoprotein (CTP) detection test has been developed that allows definitive diagnosis of PLF-related hearing loss. We report the case of a 45-year-old man who presented with right-sided tinnitus, hearing loss, and dizziness 30 years after stapes surgery. Middle ear lavage was performed after myringotomy. A preoperative diagnosis of PLF was reached using the CTP detection test. Intraoperative observations included a necrotic long process of the incus, displaced wire piston, and fibrous tissue in the oval window. Perilymph leakage was not evident. The oval window was closed with fascia, and vertigo disappeared within 2 weeks postoperatively. When PLF is suspected after stapes surgery, the CTP detection test can be a useful, highly sensitive, and less invasive method for preoperative diagnosis. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

In-pile test results of U-silicide or U-nitride coated U-7Mo particle dispersion fuel in Al

NASA Astrophysics Data System (ADS)

Kim, Yeon Soo; Park, J. M.; Lee, K. H.; Yoo, B. O.; Ryu, H. J.; Ye, B.

2014-11-01

U-silicide or U-nitride coated U-Mo particle dispersion fuel in Al (U-Mo/Al) was in-pile tested to examine the effectiveness of the coating as a diffusion barrier between the U-7Mo fuel kernels and Al matrix. This paper reports the PIE data and analyses focusing on the effectiveness of the coating in terms of interaction layer (IL) growth and general fuel performance. The U-silicide coating showed considerable success, but it also provided evidence for additional improvement for coating process. The U-nitride coated specimen showed largely inefficient results in reducing IL growth. From the test, important observations were also made that can be utilized to improve U-Mo/Al fuel performance. The heating process for coating turned out to be beneficial to suppress fuel swelling. The use of larger fuel particles confirmed favorable effects on fuel performance.

Test Generation Algorithm for Fault Detection of Analog Circuits Based on Extreme Learning Machine

PubMed Central

Zhou, Jingyu; Tian, Shulin; Yang, Chenglin; Ren, Xuelong

2014-01-01

This paper proposes a novel test generation algorithm based on extreme learning machine (ELM), and such algorithm is cost-effective and low-risk for analog device under test (DUT). This method uses test patterns derived from the test generation algorithm to stimulate DUT, and then samples output responses of the DUT for fault classification and detection. The novel ELM-based test generation algorithm proposed in this paper contains mainly three aspects of innovation. Firstly, this algorithm saves time efficiently by classifying response space with ELM. Secondly, this algorithm can avoid reduced test precision efficiently in case of reduction of the number of impulse-response samples. Thirdly, a new process of test signal generator and a test structure in test generation algorithm are presented, and both of them are very simple. Finally, the abovementioned improvement and functioning are confirmed in experiments. PMID:25610458

The effects of attention on perceptual implicit memory.

PubMed

Rajaram, S; Srinivas, K; Travers, S

2001-10-01

Reports on the effects of dividing attention at study on subsequent perceptual priming suggest that perceptual priming is generally unaffected by attentional manipulations as long as word identity is processed. We tested this hypothesis in three experiments by using the implicit word fragment completion and word stem completion tasks. Division of attention was instantiated with the Stroop task in order to ensure the processing of word identity even when the participant's attention was directed to a stimulus attribute other than the word itself. Under these conditions, we found that even though perceptual priming was significant, it was significantly reduced in magnitude. A stem cued recall test in Experiment 2 confirmed a more deleterious effect of divided attention on explicit memory. Taken together, our findings delineate the relative contributions of perceptual analysis and attentional processes in mediating perceptual priming on two ubiquitously used tasks of word fragment completion and word stem completion.

Constraints on transportation of reagents, reference materials and samples, difficulties and possible solutions: a user's perspective.

PubMed

Blanchard, P C

2006-01-01

The air transportation of infectious materials is regulated by international air transport associations and based on United Nations Model regulations which have become more practical in addressing animal disease agents. However, individual countries' import and interstate requirements determine what materials can be imported and transported, and this approval process can be long, resulting in delays in organism confirmation, use of international OIE and other reference laboratories, and acquisition of reference materials, proficiency test panels, and reagents for performing necessary testing. Delays can be prevented for permits that are required for the routine work performed by a laboratory through the use of comprehensive and annually renewed permits. This process, however, does not address new and exotic agents where time is critical to an effective emergency response. This paper suggests actions by both the OIE and regulatory authorities which can assist in streamlining and expediting the permit process.

Tungsten Contact and Line Resistance Reduction with Advanced Pulsed Nucleation Layer and Low Resistivity Tungsten Treatment

NASA Astrophysics Data System (ADS)

Chandrashekar, Anand; Chen, Feng; Lin, Jasmine; Humayun, Raashina; Wongsenakhum, Panya; Chang, Sean; Danek, Michal; Itou, Takamasa; Nakayama, Tomoo; Kariya, Atsushi; Kawaguchi, Masazumi; Hizume, Shunichi

2010-09-01

This paper describes electrical testing results of new tungsten chemical vapor deposition (CVD-W) process concepts that were developed to address the W contact and bitline scaling issues on 55 nm node devices. Contact resistance (Rc) measurements in complementary metal oxide semiconductor (CMOS) devices indicate that the new CVD-W process for sub-32 nm and beyond - consisting of an advanced pulsed nucleation layer (PNL) combined with low resistivity tungsten (LRW) initiation - produces a 20-30% drop in Rc for diffused NiSi contacts. From cross-sectional bright field and dark field transmission electron microscopy (TEM) analysis, such Rc improvement can be attributed to improved plugfill and larger in-feature W grain size with the advanced PNL+LRW process. More experiments that measured contact resistance for different feature sizes point to favorable Rc scaling with the advanced PNL+LRW process. Finally, 40% improvement in line resistance was observed with this process as tested on 55 nm embedded dynamic random access memory (DRAM) devices, confirming that the advanced PNL+LRW process can be an effective metallization solution for sub-32 nm devices.

Pharmaceutical quality by design: product and process development, understanding, and control.

PubMed

Yu, Lawrence X

2008-04-01

The purpose of this paper is to discuss the pharmaceutical Quality by Design (QbD) and describe how it can be used to ensure pharmaceutical quality. The QbD was described and some of its elements identified. Process parameters and quality attributes were identified for each unit operation during manufacture of solid oral dosage forms. The use of QbD was contrasted with the evaluation of product quality by testing alone. The QbD is a systemic approach to pharmaceutical development. It means designing and developing formulations and manufacturing processes to ensure predefined product quality. Some of the QbD elements include: Defining target product quality profile; Designing product and manufacturing processes; Identifying critical quality attributes, process parameters, and sources of variability; Controlling manufacturing processes to produce consistent quality over time. Using QbD, pharmaceutical quality is assured by understanding and controlling formulation and manufacturing variables. Product testing confirms the product quality. Implementation of QbD will enable transformation of the chemistry, manufacturing, and controls (CMC) review of abbreviated new drug applications (ANDAs) into a science-based pharmaceutical quality assessment.

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

RASMUSSEN, J.H.

1999-08-02

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AZ-102 required to satisfy the Data Quality Objectives For TWRS Privatization Phase I: Confirm Tank TIS An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO) (Nguyen 1999a), Data Quality Objectives For TWRS Privatization Phase 1: Confirm Tank TIS An Appropriate Feed Source For Low-Activity Waste Feed Batch X (LAW DQO) (Nguyen 1999b), Low Activity Waste andmore » High Level Waste Feed Data Quality Objectives (L&H DQO) (Patello et al. 1999) and Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO) (Bloom 1996). The Tank Characterization Technical Sampling Basis document (Brown et al. 1998) indicates that these issues, except the Equipment DQO apply to tank 241-AZ-102 for this sampling event. The Equipment DQO is applied for shear strength measurements of the solids segments only. Poppiti (1999) requires additional americium-241 analyses of the sludge segments. Brown et al. (1998) also identify safety screening, regulatory issues and provision of samples to the Privatization Contractor(s) as applicable issues for this tank. However, these issues will not be addressed via this sampling event. Reynolds et al. (1999) concluded that information from previous sampling events was sufficient to satisfy the safety screening requirements for tank 241 -AZ-102. Push mode core samples will be obtained from risers 15C and 24A to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples, composite the liquids and solids, perform chemical analyses, and provide subsamples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AZ-102 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plan.« less

49 CFR 40.95 - What are the adulterant cutoff concentrations for initial and confirmation tests?

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the cutoff concentrations for the initial and confirmation adulterant testing as...

49 CFR 40.95 - What are the adulterant cutoff concentrations for initial and confirmation tests?

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the cutoff concentrations for the initial and confirmation adulterant testing as...

49 CFR 40.95 - What are the adulterant cutoff concentrations for initial and confirmation tests?

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the cutoff concentrations for the initial and confirmation adulterant testing as...

49 CFR 40.95 - What are the adulterant cutoff concentrations for initial and confirmation tests?

Code of Federal Regulations, 2014 CFR

2014-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the cutoff concentrations for the initial and confirmation adulterant testing as...

49 CFR 40.95 - What are the adulterant cutoff concentrations for initial and confirmation tests?

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the cutoff concentrations for the initial and confirmation adulterant testing as...

Translating research into licensed vaccines and validated and licensed diagnostic tests.

PubMed

Hill, R E; Foley, P L; Clough, N E; Ludemann, L R; Murtle, D C

2013-01-01

The USDA Center for Veterinary Biologics (CVB) has the regulatory authority to issue licenses and permits that allow the marketing of pure, safe, potent, and effective veterinary biological products. Under the standard licensing or permitting process, a manufacturer develops, characterizes, and evaluates a product prior to licensure. The CVB evaluates the submitted information, inspects the manufacturing facilities and methods of production and testing, and confirms key product test results through independent testing. This complete and comprehensive evaluation may not be possible during the emergence of a new animal disease or in response to an introduction of a significant transboundary animal disease agent. Processes are in place in the US that allow for more rapid availability of veterinary products in an emerging or emergency animal health situation. But, it can be advantageous to attain preapproval of products prior to their anticipated need. In this article, issues associated with obtaining approval for use of a biological product under emerging or emergency conditions are discussed.

The Extended Language Network: A Meta-Analysis of Neuroimaging Studies on Text Comprehension

PubMed Central

Ferstl, Evelyn C.; Neumann, Jane; Bogler, Carsten; von Cramon, D. Yves

2010-01-01

Language processing in context requires more than merely comprehending words and sentences. Important subprocesses are inferences for bridging successive utterances, the use of background knowledge and discourse context, and pragmatic interpretations. The functional neuroanatomy of these text comprehension processes has only recently been investigated. Although there is evidence for right-hemisphere contributions, reviews have implicated the left lateral prefrontal cortex, left temporal regions beyond Wernicke’s area, and the left dorso-medial prefrontal cortex (dmPFC) for text comprehension. To objectively confirm this extended language network and to evaluate the respective contribution of right hemisphere regions, meta-analyses of 23 neuroimaging studies are reported here. The analyses used replicator dynamics based on activation likelihood estimates. Independent of the baseline, the anterior temporal lobes (aTL) were active bilaterally. In addition, processing of coherent compared with incoherent text engaged the dmPFC and the posterior cingulate cortex. Right hemisphere activations were seen most notably in the analysis of contrasts testing specific subprocesses, such as metaphor comprehension. These results suggest task dependent contributions for the lateral PFC and the right hemisphere. Most importantly, they confirm the role of the aTL and the fronto-medial cortex for language processing in context. PMID:17557297

Cognitive bias in action: evidence for a reciprocal relation between confirmation bias and fear in children.

PubMed

Remmerswaal, Danielle; Huijding, Jorg; Bouwmeester, Samantha; Brouwer, Marlies; Muris, Peter

2014-03-01

Some cognitive models propose that information processing biases and fear are reciprocally related. This idea has never been formally tested. Therefore, this study investigated the existence of a vicious circle by which confirmation bias and fear exacerbate each other. One-hundred-and-seventy-one school children (8-13 years) were first provided with threatening, ambiguous, or positive information about an unknown animal. Then they completed a computerized information search task during which they could collect additional (negative, positive, or neutral) information about the novel animal. Because fear levels were repeatedly assessed during the task, it was possible to examine the reciprocal relationship between confirmation bias and fear. A reciprocal relation of mutual reinforcement was found between confirmation bias and fear over the course of the experiment: increases in fear predicted subsequent increases in the search for negative information, and increases in the search for negative information further enhanced fear on a later point-in-time. In addition, the initial information given about the animals successfully induced diverging fear levels in the children, and determined their first inclination to search for additional information. As this study employed a community sample of primary school children, future research should test whether these results can be generalized to clinically anxious youth. These findings provide first support for the notion that fearful individuals may become trapped in a vicious circle in which fear and a fear-related confirmation bias mutually strengthen each other, thereby maintaining the anxiety pathology. Copyright © 2013 Elsevier Ltd. All rights reserved.

Titanium honeycomb acoustic lining structural and thermal test report. [for acoustic tailpipe for JT8D engine

NASA Technical Reports Server (NTRS)

Joynes, D.; Balut, J. P.

1974-01-01

The results are presented of static, fatigue and thermal testing of titanium honeycomb acoustic panels representing the acoustic tailpipe for the Pratt and Whitney Aircraft JT8D Refan engine which is being studied for use on the Boeing 727-200 airplane. Test specimens represented the engine and tailpipe flange joints, the rail to which the thrust reverser is attached and shear specimens of the tailpipe honeycomb. Specimens were made in four different batches with variations in configuration, materials and processes in each. Static strength of all test specimens exceeded the design ultimate load requirements. Fatigue test results confirmed that aluminum brazed titanium, as used in the Refan tailpipe design, meets the fatigue durability objectives. Quality of welding was found to be critical to life, with substandard welding failing prematurely, whereas welding within the process specification exceeded the panel skin life. Initial fatigue testing used short grip length bolts which failed prematurely. These were replaced with longer bolts and subsequent testing demonstrated the required life. Thermal tests indicate that perforated skin acoustic honeycomb has approximately twice the heat transfer of solid skin honeycomb.

[Dyslexia as a disfunction in successive processing].

PubMed

Pérez-Alvarez, F; Timoneda-Gallart, C

We present a study on reading and writing difficulties after normal instruction during a year. Verifying if these patients showed a specific pattern of PASS (Planning, Attention, Sequential and Simultaneous) cognitive processing; if so, it allows us a rapid diagnosis and a useful cognitive remediation according to the PASS theory of intelligence. Thirty patients were selected from neuropediatric patients because of learning disability. They were selected according to their performance on several tests of phonological aware and a test of writing to discover errors in spelling. Patients with verbal language problems, as in dysphasia, and patients with learning difficulty not determined by reading or writing were ruled out. A control group of 300 scholars was used. The translated DN:CAS battery was administered to the study group and the control group for assessing the PASS cognitive processing. Statistical factorial analysis of the control group was performed as a validity confirmation to discriminate the four PASS cognitive processes. Cluster analysis of the study group was performed to discriminate its homogeneity. Differences between means were tested with the t-Student. The four PASS cognitive processes were identified in the control group. The study group scored less than minus 1 SD in successive processing, the rest of the processes being clearly higher than minus 1 SD, and the mean of study group was inferior to control group (p = 0.001). A kind of dyslexia may be defined by disfunction in PASS successive processing.

Histochemical stains as promising means for the laser histochemical surgery of a number of pathologies

NASA Astrophysics Data System (ADS)

Piruzyan, L. A.; Mikhailovskiy, Ye. M.; Piruzyan, A. L.

1999-12-01

The directions of laboratory and clinical studies oriented to experimental confirmation of the priority concept of `laser histochemical surgery' are presented. The goal of the studies is reproduction on experimental model of a number of pathologies (in vivo and in vitro) of the `sensitization to laser radiation by staining' effect. Testing of the histochemical stains as sensitizers to laser irradiation of their `address substrates', i.e. vitally stained intracellular structures which participate in the pathologic processes evolution is under planning. The processes include: (a) metabolic disorders in the brain cells, i.e. disseminated sclerosis; (b) generalized metabolic disorders- -mucopolysaccharidosis and collagenosises (periarteritis nodosa, rheumatism, rheumatoid arthritis, sclerodermia); (3) metabolic disorders in individual organs--vessel atherosclerosis, hypercholesterolemia, myocardial infarction, cardiosclerosis, caries and parodontosis. The conditions of the studies are detailed in the recommendations along the positions: (1) disease name; (2) disease characteristics: (a) pathomorphologic, (b) biochemical; (3) stains revealing the disease signs and recommended for testing; (4) `address substrates' of the stains that are targets for laser radiation; (5) lasers recommended for the testing after the cells staining in vivo in the corresponding pathology; (6) experimental models of the pathologies suggested for the testing; (7) criteria of the stain efficiency as target sensitizer to the laser light (criteria of the `laser sensitization by staining' efficiency). Possible perspectives for the experimental clinical medicine are indicated of common histochemical stains and lasers use and of practice introduction of the `laser histochemical surgery' in the case the described concept is confirmed in experiments and clinically.

Characterization and taste-masking evaluation of acetaminophen granules: comparison between different preparation methods in a high-shear mixer.

PubMed

Albertini, Beatrice; Cavallari, Cristina; Passerini, Nadia; Voinovich, Dario; González-Rodríguez, Marisa L; Magarotto, Lorenzo; Rodriguez, Lorenzo

2004-02-01

The aim of this study was to prepare and to investigate acetaminophen taste-masked granules obtained in a high-shear mixer using three different wet granulation methods (method A: water granulation, method B: granulation with a polyvinylpyrrolidone (PVP) binding solution and method C: steam granulation). The studied formulation was: acetaminophen 15%, alpha-lactose monohydrate 30%, cornstarch 45%, polyvinylpyrrolidone K30 5% and orange flavour 5% (w/w). In vitro dissolution studies, performed at pH 6.8, showed that steam granules enabled the lower dissolution rate in comparison to the water and binding solution granules; these results were then confirmed by their lower surface reactivity (D(R)) during the dissolution process. Moreover, the results of the gustatory sensation test performed by six volunteers confirmed the taste-masking effects of the granules, especially steam granules (P<0.001). Morphological, fractal and porosity analysis were then performed to explain the dissolution profiles and the results of the gustatory sensation test. Scanning electron microscopy (SEM) analysis revealed the smoother and the more regular surface of steam granules with respect to the samples obtained using methods A and B; these results were also confirmed by their lower fractal dimension (D(s)) and porosity values. Finally, differential scanning calorimetry (DSC) results showed a shift of the melting point of the drug, which was due to the simple mixing of the components and not to the granulation processes. In conclusion, the steam granulation technique resulted a suitable method to comply the purpose of this work, without modifying the availability of the drug.

How product trial changes quality perception of four new processed beef products.

PubMed

Saeed, Faiza; Grunert, Klaus G; Therkildsen, Margrethe

2013-01-01

The purpose of this paper is the quantitative analysis of the change in quality perception of four new processed beef products from pre to post trial phases. Based on the Total Food Quality Model, differences in pre and post-trial phases were measured using repeated measures technique for cue evaluation, quality evaluation and purchase motive fulfillment. For two of the tested products, trial resulted in a decline of the evaluation of cues, quality and purchase motive fulfillment compared to pre-trial expectations. For these products, positive expectations were created by giving information about ingredients and ways of processing, which were not confirmed during trial. For the other two products, evaluations on key sensory dimensions based on trial exceeded expectations, whereas the other evaluations remained unchanged. Several demographic factors influenced the pattern of results, notably age and gender, which may be due to underlying differences in previous experience. The study gives useful insights for testing of new processed meat products before market introduction. Copyright © 2012 Elsevier Ltd. All rights reserved.

The use of ambulatory blood pressure monitoring to confirm a diagnosis of high blood pressure by primary-care physicians in Oregon.

PubMed

Carter, Brittany U; Kaylor, Mary Beth

2016-04-01

Hypertension is the most commonly diagnosed medical condition in the USA. Unfortunately, patients are misdiagnosed in primary care because of inaccurate office-based blood pressure measurements. Several US healthcare organizations currently recommend confirming an office-based hypertension diagnosis with ambulatory blood pressure monitoring to avoid overtreatment; however, its use for the purpose of confirming an office-based hypertension diagnosis is relatively unknown. This descriptive study surveyed 143 primary-care physicians in Oregon with regard to their current use of ambulatory blood pressure monitoring. Nineteen percent of the physicians reported that they would use ambulatory blood pressure monitoring to confirm an office-based hypertension diagnosis, although over half had never ordered it. The most frequent indication for ordering ambulatory blood pressure monitoring was to investigate suspected white-coat hypertension (37.3%). In addition, many of the practices did not own an ambulatory blood pressure monitoring device (79.7%) and, therefore, had to refer patients to other clinics or departments for testing. Many primary-care physicians will need to change their current clinical practice to align with the shift toward a confirmation process for office-based hypertension diagnoses to improve population health.

Pharmaceutical identifier confirmation via DART-TOF.

PubMed

Easter, Jacob L; Steiner, Robert R

2014-07-01

Pharmaceutical analysis comprises a large amount of the casework in forensic controlled substances laboratories. In order to reduce the time of analysis for pharmaceuticals, a Direct Analysis in Real Time ion source coupled with an accurate mass time-of-flight (DART-TOF) mass spectrometer was used to confirm identity. DART-TOF spectral data for pharmaceutical samples were analyzed and evaluated by comparison to standard spectra. Identical mass pharmaceuticals were differentiated using collision induced dissociation fragmentation, present/absent ions, and abundance comparison box plots; principal component analysis (PCA) and linear discriminant analysis (LDA) were used for differentiation of identical mass mixed drug spectra. Mass assignment reproducibility and robustness tests were performed on the DART-TOF spectra. Impacts on the forensic science community include a decrease in analysis time over the traditional gas chromatograph/mass spectrometry (GC/MS) confirmations, better laboratory efficiency, and simpler sample preparation. Using physical identifiers and the DART-TOF to confirm pharmaceutical identity will eliminate the use of GC/MS and effectively reduce analysis time while still complying with accepted analysis protocols. This will prove helpful in laboratories with large backlogs and will simplify the confirmation process. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Development, validation and implementation of a quadruplex real-time PCR assay for identification of potentially toxigenic corynebacteria.

PubMed

De Zoysa, Aruni; Efstratiou, Androulla; Mann, Ginder; Harrison, Timothy G; Fry, Norman K

2016-12-01

Toxigenic corynebacteria are uncommon in the UK; however, laboratory confirmation by the national reference laboratory can inform public health action according to national guidelines. Standard phenotypic tests for identification and toxin expression of isolates can take from ≥24 to ≥48 h from receipt. To decrease the time to result, a real-time PCR (qPCR) assay was developed for confirmation of both identification of Corynebacterium diphtheriae and Corynebacterium ulcerans/Corynebacterium pseudotuberculosis and detection of the diphtheria toxin gene. Target genes were the RNA polymerase β-subunit-encoding gene (rpoB) and A-subunit of the diphtheria toxin gene (tox). Green fluorescent protein DNA (gfp) was used as an internal process control. qPCR results were obtained within 3 to 4 h after receipt of isolate. The assay was validated according to published guidelines and demonstrated high diagnostic sensitivity (100 %), high specificity (98-100 %) and positive and negative predictive values of 91 to 100 % and 100 %, respectively, compared to both block-based PCR and the Elek test, together with a greatly reduced time from isolate receipt to reporting. Limitations of the qPCR assay were the inability to distinguish between C. ulcerans and C. pseudotuberculosis and that the presence of the toxin gene as demonstrated by qPCR may not always predict toxin expression. Thus, confirmation of expression of diphtheria toxin is always sought using the phenotypic Elek test. The new qPCR assay was formally introduced as the front-line test for putative toxigenic corynebacteria to inform public health action in England and Wales on 1 April 2014.

Missed opportunities: refusal to confirm reactive rapid HIV tests in the emergency department.

PubMed

Ganguli, Ishani; Collins, Jamie E; Reichmann, William M; Losina, Elena; Katz, Jeffrey N; Arbelaez, Christian; Donnell-Fink, Laurel A; Walensky, Rochelle P

2013-01-01

HIV infection remains a major US public health concern. While HIV-infected individuals now benefit from earlier diagnosis and improved treatment options, progress is tempered by large numbers of newly diagnosed patients who are lost to follow-up prior to disease confirmation and linkage to care. In the randomized, controlled USHER trial, we offered rapid HIV tests to patients presenting to a Boston, MA emergency department. Separate written informed consent was required for confirmatory testing. In a secondary analysis, we compared participants with reactive results who did and did not complete confirmatory testing to identify factors associated with refusal to complete the confirmation protocol. Thirteen of 62 (21.0%, 95% CI (11.7%, 33.2%)) participants with reactive rapid HIV tests refused confirmation; women, younger participants, African Americans, and those with fewer HIV risks, with lower income, and without primary care doctors were more likely to refuse. We projected that up to four true HIV cases were lost at the confirmation stage. These findings underscore the need to better understand the factors associated with refusal to confirm reactive HIV testing and to identify interventions that will facilitate confirmatory testing and linkage to care among these populations. ClinicalTrials.gov NCT00502944; NCT01258582.

The role of simultaneous and successive processing in EFL reading.

PubMed

Filickova, Marta; Kovalcikova, Iveta; Ropovik, Ivan

2016-10-01

This study examines the relationship between simultaneous and successive processing (the Planning, Attention, Simultaneous and Successive processing [PASS] theory processes) and reading skills in English as a foreign language (EFL). A group of 81 children were administered two batteries of tests. One was used to measure EFL reading skills, while the other one assessed simultaneous and successive processing. We hypothesised (a) cognitive processes to predict reading ability, as well as (b) the presence of a significant relationship between (c) simultaneous processing and reading comprehension and (d) successive processing and letter and word decoding. The findings confirmed that the anticipated relationships between these domains exist and are of moderate effect size. The research has helped to contribute to the understanding of how simultaneous and successive processing can affect EFL reading skills both on the level of basic word and letter decoding and reading comprehension. © 2015 International Union of Psychological Science.

Psychoacoustic processing of test signals

NASA Astrophysics Data System (ADS)

Kadlec, Frantisek

2003-10-01

For the quantitative evaluation of electroacoustic system properties and for psychoacoustic testing it is possible to utilize harmonic signals with fixed frequency, sweeping signals, random signals or their combination. This contribution deals with the design of various test signals with emphasis on audible perception. During the digital generation of signals, some additional undesirable frequency components and noise are produced, which are dependent on signal amplitude and sampling frequency. A mathematical analysis describes the origin of this distortion. By proper selection of signal frequency and amplitude it is possible to minimize those undesirable components. An additional step is to minimize the audible perception of this signal distortion by the application of additional noise (dither). For signals intended for listening tests a dither with triangular or Gaussian probability density function was found to be most effective. Signals modified this way may be further improved by the application of noise shaping, which transposes those undesirable products into frequency regions where they are perceived less, according to psychoacoustic principles. The efficiency of individual processing steps was confirmed both by measurements and by listening tests. [Work supported by the Czech Science Foundation.

Optics-Only Calibration of a Neural-Net Based Optical NDE Method for Structural Health Monitoring

NASA Technical Reports Server (NTRS)

Decker, Arthur J.

2004-01-01

A calibration process is presented that uses optical measurements alone to calibrate a neural-net based NDE method. The method itself detects small changes in the vibration mode shapes of structures. The optics-only calibration process confirms previous work that the sensitivity to vibration-amplitude changes can be as small as 10 nanometers. A more practical value in an NDE service laboratory is shown to be 50 nanometers. Both model-generated and experimental calibrations are demonstrated using two implementations of the calibration technique. The implementations are based on previously published demonstrations of the NDE method and an alternative calibration procedure that depends on comparing neural-net and point sensor measurements. The optics-only calibration method, unlike the alternative method, does not require modifications of the structure being tested or the creation of calibration objects. The calibration process can be used to test improvements in the NDE process and to develop a vibration-mode-independence of damagedetection sensitivity. The calibration effort was intended to support NASA s objective to promote safety in the operations of ground test facilities or aviation safety, in general, by allowing the detection of the gradual onset of structural changes and damage.

Defence Test and Evaluation Roadmap

DTIC Science & Technology

2008-01-01

T&E can be employed to prove, demonstrate or assess the ability of proposed and existing capability systems, new or upgraded, to satisfy specified...t&e T&E is a process to obtain information to support the objective assessment of a Capability System with known confidence, and to confirm whether...for the ADF is a ‘balanced, networked, and deployable force, staffed by dedicated and professional people, that operates within a culture of

The inclusion of ADA-SCID in expanded newborn screening by tandem mass spectrometry.

PubMed

la Marca, Giancarlo; Giocaliere, Elisa; Malvagia, Sabrina; Funghini, Silvia; Ombrone, Daniela; Della Bona, Maria Luisa; Canessa, Clementina; Lippi, Francesca; Romano, Francesca; Guerrini, Renzo; Resti, Massimo; Azzari, Chiara

2014-01-01

Severe combined immunodeficiency due to adenosine-deaminase defect (ADA-SCID) is usually deadly in childhood because of severe recurrent infections. When clinical diagnosis is done, permanent damages due to infections or metabolite accumulation are often present. Gene therapy, bone marrow transplantation or enzyme replacement therapy may be effective if started early. The aim of this study was to set-up a robust method suitable for screening with a minimized preparation process and with inexpensive running costs, for diagnosing ADA-SCID by tandem mass spectrometry. ADA-SCID satisfies all the criteria for inclusion in a newborn screening program. We describe a protocol revised to incorporate adenosine and 2-deoxyadenosine testing into an expanded newborn screening program. We assessed the effectiveness of this approach testing dried blood spots from 4 genetically confirmed early-onset and 5 delayed-onset ADA-SCID patients. Reference values were established on 50,000 healthy newborns (deoxyadenosine <0.09μmol/L, adenosine <1.61μmol/L). We also developed a second tier test to distinguish true positives from false positives and improve the positive predictive value of an initial abnormal result. In the first 18 months, the pilot project has identified a newborn with a genetically confirmed defect in adenosine deaminase (ADA) gene. The results show that the method having great simplicity, low cost and low process preparations can be fully applicable to a mass screening program. Copyright © 2013 Elsevier B.V. All rights reserved.

Cleaning, disinfection and sterilization of surface prion contamination.

PubMed

McDonnell, G; Dehen, C; Perrin, A; Thomas, V; Igel-Egalon, A; Burke, P A; Deslys, J P; Comoy, E

2013-12-01

Prion contamination is a risk during device reprocessing, being difficult to remove and inactivate. Little is known of the combined effects of cleaning, disinfection and sterilization during a typical reprocessing cycle in clinical practice. To investigate the combination of cleaning, disinfection and/or sterilization on reducing the risk of surface prion contamination. In vivo test methods were used to study the impact of cleaning alone and cleaning combined with thermal disinfection and high- or low-temperature sterilization processes. A standardized test method, based on contamination of stainless steel wires with high titres of scrapie-infected brain homogenates, was used to determine infectivity reduction. Traditional chemical methods of surface decontamination against prions were confirmed to be effective, but extended steam sterilization was more variable. Steam sterilization alone reduced the risk of prion contamination under normal or extended exposure conditions, but did show significant variation. Thermal disinfection had no impact in these studies. Cleaning with certain defined formulations in combination with steam sterilization can be an effective prion decontamination process, in particular with alkaline formulations. Low-temperature, gaseous hydrogen peroxide sterilization was also confirmed to reduce infectivity in the presence and absence of cleaning. Prion decontamination is affected by the full reprocessing cycle used on contaminated surfaces. The correct use of defined cleaning, disinfection and sterilization methods as tested in this report in the scrapie infectivity assay can provide a standard precaution against prion contamination. Copyright © 2013 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Solution processed aluminum paper for flexible electronics.

PubMed

Lee, Hye Moon; Lee, Ha Beom; Jung, Dae Soo; Yun, Jung-Yeul; Ko, Seung Hwan; Park, Seung Bin

2012-09-11

As an alternative to vacuum deposition, preparation of highly conductive papers with aluminum (Al) features is successfully achieved by the solution process consisting of Al precursor ink (AlH(3){O(C(4)H(9))(2)}) and low temperature stamping process performed at 110 °C without any serious hydroxylation and oxidation problems. Al features formed on several kinds of paper substrates (calendar, magazine, and inkjet printing paper substrates) are less than ~60 nm thick, and their electrical conductivities were found to be as good as thermally evaporated Al film or even better (≤2 Ω/□). Strong adhesion of Al features to paper substrates and their excellent flexibility are also experimentally confirmed by TEM observation and mechanical tests, such as tape and bending tests. The solution processed Al features on paper substrates show different electrical and mechanical performance depending on the paper type, and inkjet printing paper is found to be the best substrate with high and stable electrical and mechanical properties. The Al conductive papers produced by the solution process may be applicable in disposal paper electronics.

Immunoreactivity of Biochemically Purified Amandin from Thermally Processed Almonds (Prunus dulcis L.).

PubMed

Zaffran, Valerie D; Sathe, Shridhar K

2018-06-15

Almond seeds were subjected to select thermal processing and amandin was purified from processed and unprocessed (control) seeds using cryoprecipitation. Amandin immunoreactivity was assessed using two murine monoclonal antibodies (mAbs)-4C10 and 4F10 detecting human IgE-relevant conformational and linear epitopes, respectively. Overall amandin immunoreactivity following thermal treatment ranged from 64.9% to 277.8% (4C10) and 81.3% to 270.3% (4F10). Except for autoclaving (121 °C, 15 psi, 30 min) and roasting (160 °C, 30 min), the tested processing conditions resulted in increased immunoreactivity as determined by mAbs 4C10 and 4F10-based enzyme-linked immunosorbent assays (ELISAs). A significant, yet not complete, reduction in immunoreactivity was caused by autoclaving (121 °C, 15 psi, 30 min) and roasting (160 °C, 30 min). Western- and dot-blot immunoassays corroborated the ELISA results, confirming amandin thermal stability. The tested immunoassays indicated amandin to be stable, regardless of the targeted epitope and the processing method that whole almond seeds were subjected to. © 2018 Institute of Food Technologists®.

Understanding first law of thermodynamics through activities

NASA Astrophysics Data System (ADS)

Pathare, Shirish; Huli, Saurabhee; Ladage, Savita; Pradhan, H. C.

2018-03-01

The first law of thermodynamics involves several types of energies and many studies have shown that students lack awareness of them. They have difficulties in applying the law to different thermodynamic processes. These observations were confirmed in our pilot studies, carried out with students from undergraduate colleges across the whole of India. We, then, decided to develop an activity-based module to address students’ conceptual difficulties in this area. In particular, we took up the cases of both adiabatic and isothermal compression of an ideal gas. We tested, through a two-group pre and post test design, the effectiveness of the module.

Proposal of quality indicators for cardiac rehabilitation after acute coronary syndrome in Japan: a modified Delphi method and practice test.

PubMed

Ohtera, Shosuke; Kanazawa, Natsuko; Ozasa, Neiko; Ueshima, Kenji; Nakayama, Takeo

2017-01-27

Cardiac rehabilitation is underused and its quality in practice is unclear. A quality indicator is a measurable element of clinical practice performance. This study aimed to propose a set of quality indicators for cardiac rehabilitation following an acute coronary event in the Japanese population and conduct a small-size practice test to confirm feasibility and applicability of the indicators in real-world clinical practice. This study used a modified Delphi technique (the RAND/UCLA appropriateness method), a consensus method which involves an evidence review, a face-to-face multidisciplinary panel meeting and repeated anonymous rating. Evidence to be reviewed included clinical practice guidelines available in English or Japanese and existing quality indicators. Performance of each indicator was assessed retrospectively using medical records at a university hospital in Japan. 10 professionals in cardiac rehabilitation for the consensus panel. In the literature review, 23 clinical practice guidelines and 16 existing indicators were identified to generate potential indicators. Through the consensus-building process, a total of 30 indicators were assessed and finally 13 indicators were accepted. The practice test (n=39) revealed that 74% of patients underwent cardiac rehabilitation. Median performance of process measures was 93% (IQR 46-100%). 'Communication with the doctor who referred the patient to cardiac rehabilitation' and 'continuous participation in cardiac rehabilitation' had low performance (32% and 38%, respectively). A modified Delphi technique identified a comprehensive set of quality indicators for cardiac rehabilitation. The single-site, small-size practice test confirmed that most of the proposed indicators were measurable in real-world clinical practice. However, some clinical processes which are not covered by national health insurance in Japan had low performance. Further studies will be needed to clarify and improve the quality of care in cardiac rehabilitation. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Processing postmortem specimens with C18-carboxypropylbetaine and analysis by PCR to develop an antemortem test for Mycobacterium avium infections in ducks.

PubMed

Thornton, C G; Cranfield, M R; MacLellan, K M; Brink, T L; Strandberg, J D; Carlin, E A; Torrelles, J B; Maslow, J N; Hasson, J L; Heyl, D M; Sarro, S J; Chatterjee, D; Passen, S

1999-03-01

Mycobacterium avium is the causative agent of the avian mycobacteriosis commonly known as avian tuberculosis (ATB). This infection causes disseminated disease, is difficult to diagnose, and is of serious concern because it causes significant mortality in birds. A new method was developed for processing specimens for an antemortem screening test for ATB. This novel method uses the zwitterionic detergent C18-carboxypropylbetaine (CB-18). Blood, bone marrow, bursa, and fecal specimens from 28 ducks and swabs of 20 lesions were processed with CB-18 for analysis by smear, culture, and polymerase chain reaction (PCR). Postmortem examination confirmed nine of these birds as either positive or highly suspect for disseminated disease. The sensitivities of smear, culture, and PCR, relative to postmortem analysis and independent of specimen type, were 44.4%, 88.9%, and 100%, respectively, and the specificities were 84.2%, 57.9%, and 15.8%, respectively. Reductions in specificity were due primarily to results among fecal specimens. However, these results were clustered among a subset of birds, suggesting that these tests actually identified birds in early stages of the disease. Restriction fragment length polymorphism mapping identified one strain of M. avium (serotype 1) that was isolated from lesions, bursa, bone marrow, blood, and feces of all but three of the culture-positive birds. In birds with confirmed disease, blood had the lowest sensitivity and the highest specificity by all diagnostic methods. Swabs of lesions provided the highest sensitivity by smear and culture (33.3% and 77.8%, respectively), whereas fecal specimens had the highest sensitivity by PCR (77.8%). The results of this study indicate that processing fecal specimens with CB-18, followed by PCR analysis, may provide a valuable first step for monitoring the presence of ATB in birds.

Revealing the synergetic effects in Ni nanoparticle-carbon nanotube hybrids by scanning transmission X-ray microscopy and their application in the hydrolysis of ammonia borane

NASA Astrophysics Data System (ADS)

Zhao, Guanqi; Zhong, Jun; Wang, Jian; Sham, Tsun-Kong; Sun, Xuhui; Lee, Shuit-Tong

2015-05-01

The hybrids of carbon nanotubes (CNTs) and the supported Ni nanoparticles (NPs) have been studied by scanning transmission X-ray microscopy (STXM) and tested by the hydrolysis reaction of ammonia borane (AB, NH3BH3). Data clearly showed the existence of a strong interaction between Ni NPs and thin CNTs (C-O-Ni bonds), which favored the tunable (buffer) electronic structure of Ni NPs facilitating the catalytic process. The hydrolysis process of AB confirmed the hypothesis that the hybrids with a strong interfacial interaction would show superior catalytic performance, while the hybrids with a weak interfacial interaction show poor performance. Our results provide a wealth of detailed information regarding the electronic structure of the NP-CNT hybrids and provide guidance towards the rational design of high-performance catalysts for energy applications.The hybrids of carbon nanotubes (CNTs) and the supported Ni nanoparticles (NPs) have been studied by scanning transmission X-ray microscopy (STXM) and tested by the hydrolysis reaction of ammonia borane (AB, NH3BH3). Data clearly showed the existence of a strong interaction between Ni NPs and thin CNTs (C-O-Ni bonds), which favored the tunable (buffer) electronic structure of Ni NPs facilitating the catalytic process. The hydrolysis process of AB confirmed the hypothesis that the hybrids with a strong interfacial interaction would show superior catalytic performance, while the hybrids with a weak interfacial interaction show poor performance. Our results provide a wealth of detailed information regarding the electronic structure of the NP-CNT hybrids and provide guidance towards the rational design of high-performance catalysts for energy applications. Electronic supplementary information (ESI) available: Magnified TEM images, high resolution TEM images and the particle size distributions of the samples, the STXM results of a thick tube at different positions, XPS results, stability test. See DOI: 10.1039/c5nr01168j

Highly reliable oxide VCSELs for datacom applications

NASA Astrophysics Data System (ADS)

Aeby, Ian; Collins, Doug; Gibson, Brian; Helms, Christopher J.; Hou, Hong Q.; Lou, Wenlin; Bossert, David J.; Wang, Charlie X.

2003-06-01

In this paper we describe the processes and procedures that have been developed to ensure high reliability for Emcore"s 850 nm oxide confined GaAs VCSELs. Evidence from on-going accelerated life testing and other reliability studies that confirm that this process yields reliable products will be discussed. We will present data and analysis techniques used to determine the activation energy and acceleration factors for the dominant wear-out failure mechanisms for our devices as well as our estimated MTTF of greater than 2 million use hours. We conclude with a summary of internal verification and field return rate validation data.

Nonword repetition in lexical decision: support for two opposing processes.

PubMed

Wagenmakers, Eric-Jan; Zeelenberg, René; Steyvers, Mark; Shiffrin, Richard; Raaijmakers, Jeroen

2004-10-01

We tested and confirmed the hypothesis that the prior presentation of nonwords in lexical decision is the net result of two opposing processes: (1) a relatively fast inhibitory process based on global familiarity; and (2) a relatively slow facilitatory process based on the retrieval of specific episodic information. In three studies, we manipulated speed-stress to influence the balance between the two processes. Experiment 1 showed item-specific improvement for repeated nonwords in a standard "respond-when-ready" lexical decision task. Experiment 2 used a 400-ms deadline procedure and showed performance for nonwords to be unaffected by up to four prior presentations. In Experiment 3 we used a signal-to-respond procedure with variable time intervals and found negative repetition priming for repeated nonwords. These results can be accounted for by dual-process models of lexical decision.

Observations and simulations of specularly reflected He++ at Earth's quasiperpendicular bow shock

NASA Astrophysics Data System (ADS)

Broll, J. M.; Fuselier, S. A.; Trattner, K. J.; Anderson, B. J.; Burch, J. L.; Giles, B. L.

2016-12-01

Specular reflection of protons at Earth's quasiperpendicular bow shock is an important process for supercritical shock dissipation. Previous studies have found evidence of He++ specular reflection from reduced particle distributions downstream from the shock, but confirmation of the process for heavier ions in the shock foot was not possible due to time resolution constraints. We present He++ distributions, observed by MMS in a quasiperpendicular bow shock crossing, that are consistent with specularly reflected He++. We also investigate the He++ dynamics with test-particle simulations in a simulated shock based on this crossing and we conduct wave analysis to determine what processes lead to separate gyrotropization timescales for the transmitted and reflected populations.

Setting appropriate pass or fail cut-off criteria for tests to reflect real life listening difficulties in children with suspected auditory processing disorder.

PubMed

Ahmmed, Ansar U; Ahmmed, Afsara A

2016-05-01

This paper explores the pass or fail cut-off criteria, the number of test fails, and the nature of tests that are most appropriate in predicting listening difficulties (LiD) in children with suspected APD (SusAPD). One hundred and nine English-speaking children (67 males, 42 females) aged between 6 and 11 years with SusAPD were assessed. The Children's Auditory Performance Scale (CHAPS) scores 2 SD below the mean were taken as markers of LiD in different listening conditions. Binary logistic regression analyses were carried out to evaluate the cut-off criterion (2 SD or 1.5 SD or 1 SD below the mean) of failing at least two tests, from the SCAN-C and IMAP test batteries, which significantly predicted LiD. Analyses were also carried out to assess if the group of auditory processing (AP) or cognitive or combination of AP plus cognitive tests were significant in predicting LiD. Receiver Operative Characteristic (ROC) curves were also explored to evaluate how the sensitivity and specificity in confirming LiD varied with the number of test fails. Filtered Words, Competing Words, Competing Sentences, VCV in ICRA noise, Digit Span, Sight Word Reading and the Cued Auditory Attention tests correlated with one or more of the CHAPS domains. Failing at least two of these tests 1.5 SD below the mean significantly predicted (p<.05) CHAPS Ideal scores 2 SD below the mean, and failing at least two of the tests 1 SD below the mean significantly predicted (p<.05) CHAPS Memory and CHAPS Attention scores 2 SD below the mean. The combination of AP plus cognitive tests had significantly higher ability to predict CHAPS Ideal, Memory and Attention scores, compared to the group of AP or cognitive tests separately. ROC curves showed that failing at least two of the tests was associated with the best sensitivity and specificity in predicting LiD. Of the different CHAPS domains only the CHAPS Ideal, Memory and Attention correlated with the APD tests. Failing at least two APD tests from a combination of AP and cognitive tests 1 SD and 1.5 SD below the mean, but not 2 SD, is more appropriate in confirming LiD. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abraham, TJ

A testing facility (Cold Test Loop) was constructed and operated to demonstrate the efficacy of the Accelerated Waste Retrieval (AWR) Project's planned sluicing approach to the remediation of Silos 1 and 2 at the Fernald Environmental Management Project near Cincinnati, Ohio. The two silos contain almost 10,000 tons of radium-bearing low-level waste, which consists primarily of solids of raffinates from processing performed on ores from the Democratic Republic of Congo (commonly referred to as ''Belgium Congo ores'') for the recovery of uranium. These silos are 80 ft in diameter, 36 ft high to the center of the dome, and 26.75more » ft to the top of the vertical side walls. The test facility contained two test systems, each designed for a specific purpose. The first system, the Integrated Test Loop (ITL), a near-full-scale plant including the actual equipment to be installed at the Fernald Site, was designed to demonstrate the sluicing operation and confirm the selection of a slurry pump, the optimal sluicing nozzle operation, and the preliminary design material balance. The second system, the Component Test Loop (CTL), was designed to evaluate many of the key individual components of the waste retrieval system over an extended run. The major results of the initial testing performed during July and August 2002 confirmed that the AWR approach to sluicing was feasible. The ITL testing confirmed the following: (1) The selected slurry pump (Hazleton 3-20 type SHW) performed well and is suitable for AWR application. However, the pump's motor should be upgraded to a 200-hp model and be driven by a 150-hp variable-frequency drive (VFD). A 200-hp VFD is not much more expensive and would allow the pump to operate at full speed. (2) The best nozzle performance was achieved by using 15/16-in. nozzles operated alternately. This configuration appeared to most effectively mine the surrogate. (3) The Solartron densitometer, which was tested as an alternative mass flow measurement device, did not operate effectively. Consequently, it is not suitable for application to the AWR process. (4) Initially, the spray ring (operated at approximately 2300 psi) and the nozzles provided by the pump vendor did not perform acceptably. The nozzles were replaced with a more robust model, and the performance was then acceptable. (5) The average solids concentration achieved in the slurry before Bentogrout addition was approximately 16% by weight. The solids concentration of the slurry after Bentogrout addition ranged from 26% to approximately 40%. The slurry pump and ITL system performed well at every concentration. No line plugging or other problems were noted. The results of the CTL runs and later ITL testing are summarized in an appendix to this report.« less

9 CFR 149.6 - Slaughter facilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... result based on an ELISA method and is confirmed positive by further testing using the digestion method... decertified. (C) If a test sample yields a positive test result based on an ELISA method, but is not confirmed...

9 CFR 149.6 - Slaughter facilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

... result based on an ELISA method and is confirmed positive by further testing using the digestion method... decertified. (C) If a test sample yields a positive test result based on an ELISA method, but is not confirmed...

9 CFR 149.6 - Slaughter facilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... result based on an ELISA method and is confirmed positive by further testing using the digestion method... decertified. (C) If a test sample yields a positive test result based on an ELISA method, but is not confirmed...

9 CFR 149.6 - Slaughter facilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

... result based on an ELISA method and is confirmed positive by further testing using the digestion method... decertified. (C) If a test sample yields a positive test result based on an ELISA method, but is not confirmed...

9 CFR 149.6 - Slaughter facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... result based on an ELISA method and is confirmed positive by further testing using the digestion method... decertified. (C) If a test sample yields a positive test result based on an ELISA method, but is not confirmed...

ESGE-ESGENA technical specification for process validation and routine testing of endoscope reprocessing in washer-disinfectors according to EN ISO 15883, parts 1, 4, and ISO/TS 15883-5.

PubMed

Beilenhoff, Ulrike; Biering, Holger; Blum, Reinhard; Brljak, Jadranka; Cimbro, Monica; Dumonceau, Jean-Marc; Hassan, Cesare; Jung, Michael; Neumann, Christiane; Pietsch, Michael; Pineau, Lionel; Ponchon, Thierry; Rejchrt, Stanislav; Rey, Jean-François; Schmidt, Verona; Tillett, Jayne; van Hooft, Jeanin

2017-12-01

1 Prerequisites. The clinical service provider should obtain confirmation from the endoscope washer-disinfector (EWD) manufacturer that all endoscopes intended to be used can be reprocessed in the EWD. 2 Installation qualification. This can be performed by different parties but national guidelines should define who has the responsibilities, taking into account legal requirements. 3 Operational qualification. This should include parametric tests to verify that the EWD is working according to its specifications. 4 Performance qualification. Testing of cleaning performance, microbiological testing of routinely used endoscopes, and the quality of the final rinse water should be considered in all local guidelines. The extent of these tests depends on local requirements. According to the results of type testing performed during EWD development, other parameters can be tested if local regulatory authorities accept this. Chemical residues on endoscope surfaces should be searched for, if acceptable test methods are available. 5 Routine inspections. National guidelines should consider both technical and performance criteria. Individual risk analyses performed in the validation and requalification processes are helpful for defining appropriate test frequencies for routine inspections. © Georg Thieme Verlag KG Stuttgart · New York.

The Superorbital Expansion Tube concept, experiment and analysis

NASA Technical Reports Server (NTRS)

Neely, A. J.; Morgan, R. G.

1995-01-01

In response to the need for ground testing facilities for super orbital re-entry research, a small scale facility has been set up at the University of Queensland to demonstrate the superorbital expansion tube concept. This unique device is a free piston driven, triple diaphragm, impulse shock facility which uses the enthalpy multiplication mechanism of the unsteady expansion process and the addition of a secondary shock driver to further heat the driver gas. The pilot facility has been operated to produce quasi-steady test flows in air with shock velocities in excess of 13 km/s and with a usable test flow duration of the order of 15 micro sec. an experimental condition produced in the facility with total enthalpy of 108 MJ/kg and a total pressure of 335 MPa is reported. A simple analytical flow model which accounts for non-ideal rupture of the light tertiary diaphragm and the resulting entropy increase in the test gas is discussed. It is shown that equilibrium calculations more accurately model the unsteady expansion process than calculations assuming frozen chemistry. This is because the high enthalpy flows produced in the facility can only be achieved if the chemical energy stored in the test flow during shock heating of the test gas is partially returned to the flow during the process of unsteady expansion. Measurements of heat transfer rates to a flat plate demonstrate the usability of test flow for aerothermodynamic testing and comparison of these rates with empirical calculations confirms the usable accuracy of the flow model.

Innovative application of the moisture analyzer for determination of dry mass content of processed cheese

NASA Astrophysics Data System (ADS)

Kowalska, Małgorzata; Janas, Sławomir; Woźniak, Magdalena

2018-04-01

The aim of this work was the presentation of an alternative method of determination of the total dry mass content in processed cheese. The authors claim that the presented method can be used in industry's quality control laboratories for routine testing and for quick in-process control. For the test purposes both reference method of determination of dry mass in processed cheese and moisture analyzer method were used. The tests were carried out for three different kinds of processed cheese. In accordance with the reference method, the sample was placed on a layer of silica sand and dried at the temperature of 102 °C for about 4 h. The moisture analyzer test required method validation, with regard to drying temperature range and mass of the analyzed sample. Optimum drying temperature of 110 °C was determined experimentally. For Hochland cream processed cheese sample, the total dry mass content, obtained using the reference method, was 38.92%, whereas using the moisture analyzer method, it was 38.74%. An average analysis time in case of the moisture analyzer method was 9 min. For the sample of processed cheese with tomatoes, the reference method result was 40.37%, and the alternative method result was 40.67%. For the sample of cream processed cheese with garlic the reference method gave value of 36.88%, and the alternative method, of 37.02%. An average time of those determinations was 16 min. Obtained results confirmed that use of moisture analyzer is effective. Compliant values of dry mass content were obtained for both of the used methods. According to the authors, the fact that the measurement took incomparably less time for moisture analyzer method, is a key criterion of in-process control and final quality control method selection.

Using the National Assessment of Educational Progress To Confirm State Test Results. A Report of the Ad Hoc Committee on Confirming Test Results.

ERIC Educational Resources Information Center

National Assessment Governing Board, Washington, DC.

The National Assessment Governing Board has recognized the need to study associated policy and technical issues to ensure that the National Assessment of Educational Progress (NAEP) is ready to do the best job possible if called on to confirm the results of state achievement testing under the No Child Left Behind Act. This report describes the…

Examination of a size-change test for photovoltaic encapsulation materials

NASA Astrophysics Data System (ADS)

Miller, David C.; Gu, Xiaohong; Ji, Liang; Kelly, George; Nickel, Nichole; Norum, Paul; Shioda, Tsuyoshi; Tamizhmani, Govindasamy; Wohlgemuth, John H.

2012-10-01

We examine a proposed test standard that can be used to evaluate the maximum representative change in linear dimensions of sheet encapsulation products for photovoltaic modules (resulting from their thermal processing). The proposed protocol is part of a series of material-level tests being developed within Working Group 2 of the Technical Committee 82 of the International Electrotechnical Commission. The characterization tests are being developed to aid module design (by identifying the essential characteristics that should be communicated on a datasheet), quality control (via internal material acceptance and process control), and failure analysis. Discovery and interlaboratory experiments were used to select particular parameters for the size-change test. The choice of a sand substrate and aluminum carrier is explored relative to other options. The temperature uniformity of +/-5°C for the substrate was confirmed using thermography. Considerations related to the heating device (hot-plate or oven) are explored. The time duration of 5 minutes was identified from the time-series photographic characterization of material specimens (EVA, ionomer, PVB, TPO, and TPU). The test procedure was revised to account for observed effects of size and edges. The interlaboratory study identified typical size-change characteristics, and also verified the absolute reproducibility of +/-5% between laboratories.

A test to verify the biocompatibility of a method for plant culture in a microgravity environment

NASA Technical Reports Server (NTRS)

Brown, A. H.; Chapman, D. K.

1984-01-01

We report a pioneering attempt to use the NASA Shuttle Orbiter Middeck locker facility to acquire data on plant growth in near weightlessness. The information was needed to confirm the suitability of a plant culture system to be used in an experiment scheduled for the first Spacelab mission. The test was designed to measure germination and early seedling growth in a series of soil mixtures covering a range of water contents. Empirical determination of growth dependence on moisture content was required because both in theory and from Soviet flight experience it seemed possible that the dependence function in near weightlessness could be critically different from what we had measured on Earth. Such a difference could invalidate the future test in Spacelab 1 of gravity dependence of the differential growth process, circumnutation. After two failed attempts sufficient measurements were obtained from the third Shuttle Orbiter flight test to confirm the biocompatibility of the plant culture system--viz. soil moisture content variations had the same effect in near weightlessness as at 1 g. A number of supplemental observations about middeck locker conditions in Shuttle flight are presented. These may prove helpful to would-be experimenters who will plan to take advantage of future Shuttle flight opportunities for biological research.

Orion Ground Test Article Water Impact Tests: Photogrammetric Evaluation of Impact Conditions

NASA Technical Reports Server (NTRS)

Vassilakos, Gregory J.; Mark, Stephen D.

2018-01-01

The Ground Test Article (GTA) is an early production version of the Orion Crew Module (CM). The structural design of the Orion CM is being developed based on LS-DYNA water landing simulations. As part of the process of confirming the accuracy of LS-DYNA water landing simulations, the GTA water impact test series was conducted at NASA Langley Research Center (LaRC) to gather data for comparison with simulations. The simulation of the GTA water impact tests requires the accurate determination of the impact conditions. To accomplish this, the GTA was outfitted with an array of photogrammetry targets. The photogrammetry system utilizes images from two cameras with a specialized tracking software to determine time histories for the 3-D coordinates of each target. The impact conditions can then be determined from the target location data.

Provocation testing to assist craniomandibular pain diagnosis.

PubMed

DuPont, John S; Brown, Christopher E

2010-04-01

Patients with TMD often present with complex pain symptoms, which can make it difficult to reach a diagnosis. Usually palpation of the masticatory muscles and TM joints, range of motion testing and imaging are used in the diagnostic process. Sometimes it is necessary to evaluate the jaw moving muscles from a functional prospective because they cannot be palpated due to inaccessibility or because they have other structures that are more superficial to them. In these instances, provocation testing can be a helpful adjunct in providing some insight into what is occurring in the area being tested and localizing a suspected source of pain. Anesthesia blocking can be used to confirm any positive findings. This article explores several provocation tests that can be used to evaluate conditions of the masticatory musculature, the TM joints and the stylomandibular ligament.

Acetification of rice wine by Acetobacter aceti using loofa sponge in a low-cost reciprocating shaker.

PubMed

Krusong, W; Tantratian, S

2014-11-01

To maximize acetification rate (ETA) by adsorption of acetic acid bacteria (AAB) on loofa sponge matrices (LSM). AAB were adsorbed on LSM, and the optimal shaking rate was determined for maximized AAB growth and oxygen availability. Results confirm that the 1 Hz reciprocating shaking rate with 40% working volume (liquid volume 24 l, tank volume 60 l) achieved a high oxygen transfer coefficient (k(L)a). The highest ETA was obtained at 50% (w:v) LSM-AAB:culture medium at 30 ± 2°C (P ≤ 0·05). To test process consistency, nine sequential acetification cycles were run using LSM-AAB and comparing it with no LSM. The highest ETA (1·701-2·401 g l(-1) d(-1)) was with LSM-AAB and was associated with the highest biomass of AAB, confirmed by SEM images. Results confirm that LSM-AAB works well as an inert substrate for AAB. High oxygenation was maintained by a reciprocating shaker. Both shaking and LSM were important in increasing ETA. High cell biomass in LSM-AAB provides good conditions for higher ETAs of quick acetification under adequate oxygen transfer by reciprocating shaker. It is a sustainable process for small-scale vinegar production system requiring minimal set-up cost. © 2014 The Society for Applied Microbiology.

A Positive Generation Effect on Memory for Auditory Context.

PubMed

Overman, Amy A; Richard, Alison G; Stephens, Joseph D W

2017-06-01

Self-generation of information during memory encoding has large positive effects on subsequent memory for items, but mixed effects on memory for contextual information associated with items. A processing account of generation effects on context memory (Mulligan in Journal of Experimental Psychology: Learning, Memory, and Cognition, 30(4), 838-855, 2004; Mulligan, Lozito, & Rosner in Journal of Experimental Psychology: Learning, Memory, and Cognition, 32(4), 836-846, 2006) proposes that these effects depend on whether the generation task causes any shift in processing of the type of context features for which memory is being tested. Mulligan and colleagues have used this account to predict various negative effects of generation on context memory, but the account also predicts positive generation effects under certain circumstances. The present experiment provided a critical test of the processing account by examining how generation affected memory for auditory rather than visual context. Based on the processing account, we predicted that generation of rhyme words should enhance processing of auditory information associated with the words (i.e., voice gender), whereas generation of antonym words should have no effect. These predictions were confirmed, providing support to the processing account.

Testing a self-determination theory intervention for motivating tobacco cessation: supporting autonomy and competence in a clinical trial.

PubMed

Williams, Geoffrey C; McGregor, Holly A; Sharp, Daryl; Levesque, Chantal; Kouides, Ruth W; Ryan, Richard M; Deci, Edward L

2006-01-01

A longitudinal randomized trial tested the self-determination theory (SDT) intervention and process model of health behavior change for tobacco cessation (N = 1006). Adult smokers were recruited for a study of smokers' health and were assigned to intensive treatment or community care. Participants were relatively poor and undereducated. Intervention patients perceived greater autonomy support and reported greater autonomous and competence motivations than did control patients. They also reported greater medication use and significantly greater abstinence. Structural equation modeling analyses confirmed the SDT process model in which perceived autonomy support led to increases in autonomous and competence motivations, which in turn led to greater cessation. The causal role of autonomy support in the internalization of autonomous motivation, perceived competence, and smoking cessation was supported. Copyright 2006 APA, all rights reserved.

Qualification of an evaluated butterfly-packaged DFB laser designed for space applications

NASA Astrophysics Data System (ADS)

Tornow, S.; Stier, C.; Buettner, T.; Laurent, T.; Kneier, M.; Bru, J.; Lien, Y.

2017-11-01

An extended qualification program has proven the quality of a previously evaluated semiconductor laser diode, which is intended to be used in a subsystem for the GAIA mission. We report on results of several reliability tests performed in subgroups. The requirements of the procurement specification with respect to reliability and desired manufacturing processes were confirmed. This is an example for successful collaboration between component supplier, system integrator and payload responsible party.

The Whole Is More than the Sum of Its Parts--Audiovisual Processing of Phonemes Investigated with ERPs

ERIC Educational Resources Information Center

Hessler, Dorte; Jonkers, Roel; Stowe, Laurie; Bastiaanse, Roelien

2013-01-01

In the current ERP study, an active oddball task was carried out, testing pure tones and auditory, visual and audiovisual syllables. For pure tones, an MMN, an N2b, and a P3 were found, confirming traditional findings. Auditory syllables evoked an N2 and a P3. We found that the amplitude of the P3 depended on the distance between standard and…

Controls in new construction reactors-factory testing of the non-safety portion of the Lungmen nuclear power plant distributed control system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Y. S.; Dick, J. W.; Tetirick, C. W.

2006-07-01

The construction permit for Taipower's Lungmen Nuclear Units 1 and 2, two ABWR plants, was issued on March 17, 1999[1], The construction of these units is progressing actively at site. The digital I and C system supplied by GE, which is designated as the Distributed Control and Information System (DCIS) in this project, is being implemented primarily at one vendor facility. In order to ensure the reliability, safety and availability of the DCIS, it is required to comprehensively test the whole DCIS in factory. This article describes the test requirements and acceptance criteria for functional testing of the Non-Safety Distributedmore » Control and Information system (DCIS) for Taiwan Power's Lungmen Units 1 and 2 GE selected Invensys as the equipment supplier for this Non-Safety portion of DCIS. The DCIS system of the Lungmen Units is a physically distributed control system. Field transmitters are connected to hard I/O terminal inputs on the Invensys I/A system. Once the signal is digitized on FBMs (Field Bus Modules) in Remote Multiplexing Units (RMUs), the signal is passed into an integrated control software environment. Control is based on the concept of compounds and blocks where each compound is a logical collection of blocks that performs a control function. Each point identified by control compound and block can be individually used throughout the DCIS system by referencing its unique name. In the Lungmen Project control logic and HSI (Human System Interface) requirements are divided into individual process systems called MPLs (Master Parts List). Higher-level Plant Computer System (PCS) algorithms access control compounds and blocks in these MPLs to develop functions. The test requirements and acceptance criteria for the DCIS system of the Lungmen Project are divided into three general categories (see 1,2,3 below) of verification, which in turn are divided into several specific tests: 1. DCIS System Physical Checks a) RMU Test - To confirm that the hard I/O database is installed on the DCIS and is physically addressed correctly. Test process is injecting a signal at each DCIS hard I/O terminal boundary and verifying correct receipt on the DCIS. b) DCIS Network Stress Test - Confirms system viability under extreme high load conditions beyond the plant could ever experience. Load conditions include alarm showers on the DCIS system to emulate plant upsets. c) System Hardware Configuration Test - These are typical checks of the DCIS system hardware including fault reporting, redundancy, and normal computer functions. d) Performance Test - Test confirms high level hardware and system capability attributes such as control system time response, 'cold start' reboots, and processor loading e) Electromagnetic compatibility tests - To verify the electromagnetic viability of the system and individual components 2. Implementation of Plant Systems and Systems Integration a) MPL Logic Tests -To confirm control functions implemented to system logic performs as expected, and that parameters are passed correctly between system control schemes. b) Data Link (Gateway) Tests- To verify third party interfaces to the DCIS. c) Plant Computer System (PCS) Logic Tests- Tests to verify that higher-level PCS logic is correctly implemented, performs as expected, and parameters are passed correctly between PCS sub-systems and MPL systems. Included the PCS sub-systems, Safety Parameter Display System, Historian, Alarms, Maintenance monitoring etc. 3. Unique Third Party Interfacing and Integration into the DCIS The set of controls for Automatic Power Regulation, Feedwater, and Recirculation Flow are specific in that these systems are implemented on third party Triple Modular Redundant (TMR) hardware, which was connected to the DCIS and are tested via full simulation. The TMR system is supplied by GE Control Solutions on the Mark Vie platform. (authors)« less

Optical performance of random anti-reflection structured surfaces (rARSS) on spherical lenses

NASA Astrophysics Data System (ADS)

Taylor, Courtney D.

Random anti-reflection structured surfaces (rARSS) have been reported to improve transmittance of optical-grade fused silica planar substrates to values greater than 99%. These textures are fabricated directly on the substrates using reactive-ion/inductively-coupled plasma etching (RIE/ICP) techniques, and often result in transmitted spectra with no measurable interference effects (fringes) for a wide range of wavelengths. The RIE/ICP processes used in the fabrication process to etch the rARSS is anisotropic and thus well suited for planar components. The improvement in spectral transmission has been found to be independent of optical incidence angles for values from 0° to +/-30°. Qualifying and quantifying the rARSS performance on curved substrates, such as convex lenses, is required to optimize the fabrication of the desired AR effect on optical-power elements. In this work, rARSS was fabricated on fused silica plano-convex (PCX) and plano-concave (PCV) lenses using a planar-substrate optimized RIE process to maximize optical transmission in the range from 500 to 1100 nm. An additional set of lenses were etched in a non-optimized ICP process to provide additional comparisons. Results are presented from optical transmission and beam propagation tests (optimized lenses only) of rARSS lenses for both TE and TM incident polarizations at a wavelength of 633 nm and over a 70° full field of view in both singlet and doublet configurations. These results suggest optimization of the fabrication process is not required, mainly due to the wide angle-of-incidence AR tolerance performance of the rARSS lenses. Non-optimized recipe lenses showed low transmission enhancement, and confirmed the need to optimized etch recipes prior to process transfer of PCX/PCV lenses. Beam propagation tests indicated no major beam degradation through the optimized lens elements. Scanning electron microscopy (SEM) images confirmed different structure between optimized and non-optimized samples. SEM images also indicated isotropically-oriented surface structures on both types of lenses.

Quality of care for patients with diabetes mellitus type 2 in ‘model practices’ in Slovenia – first results

PubMed Central

Mlakar, Mitja

2016-01-01

Abstract Background A new organisation at the primary level, called model practices, introduces a 0.5 full-time equivalent nurse practitioner as a regular member of the team. Nurse practitioners are in charge of registers of chronic patients, and implement an active approach into medical care. Selected quality indicators define the quality of management. The majority of studies confirm the effectiveness of the extended team in the quality of care, which is similar or improved when compared to care performed by the physician alone. The aim of the study is to compare the quality of management of patients with diabetes mellitus type 2 before and after the introduction of model practices. Methods A cohort retrospective study was based on medical records from three practices. Process quality indicators, such as regularity of HbA1c measurement, blood pressure measurement, foot exam, referral to eye exam, performance of yearly laboratory tests and HbA1c level before and after the introduction of model practices were compared. Results The final sample consisted of 132 patients, whose diabetes care was exclusively performed at the primary care level. The process of care has significantly improved after the delivery of model practices. The most outstanding is the increase of foot exam and HbA1c testing. We could not prove better glycaemic control (p>0.1). Nevertheless, the proposed benchmark for the suggested quality process and outcome indicators were mostly exceeded in this cohort. Conclusion The introduction of a nurse into the team improves the process quality of care. Benchmarks for quality indicators are obtainable. Better outcomes of care need further confirmation. PMID:27703537

Quality of care for patients with diabetes mellitus type 2 in 'model practices' in Slovenia - first results.

PubMed

Petek, Davorina; Mlakar, Mitja

2016-09-01

A new organisation at the primary level, called model practices, introduces a 0.5 full-time equivalent nurse practitioner as a regular member of the team. Nurse practitioners are in charge of registers of chronic patients, and implement an active approach into medical care. Selected quality indicators define the quality of management. The majority of studies confirm the effectiveness of the extended team in the quality of care, which is similar or improved when compared to care performed by the physician alone. The aim of the study is to compare the quality of management of patients with diabetes mellitus type 2 before and after the introduction of model practices. A cohort retrospective study was based on medical records from three practices. Process quality indicators, such as regularity of HbA1c measurement, blood pressure measurement, foot exam, referral to eye exam, performance of yearly laboratory tests and HbA1c level before and after the introduction of model practices were compared. The final sample consisted of 132 patients, whose diabetes care was exclusively performed at the primary care level. The process of care has significantly improved after the delivery of model practices. The most outstanding is the increase of foot exam and HbA1c testing. We could not prove better glycaemic control (p>0.1). Nevertheless, the proposed benchmark for the suggested quality process and outcome indicators were mostly exceeded in this cohort. The introduction of a nurse into the team improves the process quality of care. Benchmarks for quality indicators are obtainable. Better outcomes of care need further confirmation.

Psychological and Physiological Processes in Figure-Tracing Abilities Measured Using a Tablet Computer: A Study with 7 and 9 Years Old Children

PubMed Central

Giammarco, Enrico; Di Sano, Sergio; Aureli, Tiziana; Cerratti, Paola; Fanò-Illic, Giorgio; Pietrangelo, Tiziana

2016-01-01

The present study investigated the use of a tablet computer to assess figure-tracing skills and their relationships with psychological (visual–perceptual processes, cognitive processes, handwriting skills) and physiological (body mass index, isometric strength of arms) parameters with school-children of second (7–8-year-olds) and fourth (9–10-year-olds) grades. We were also interested in gender differences. The task required tracing of geometric figures on a template, shown on a tablet screen in light gray, for the segments that make up the target figure, one at a time. This figure-tracing tablet test allows acquisition and automated analysis of four parameters: number of strokes (pen lift) for each segment; oscillations of lines drawn with respect to reference lines; pressure of pen on tablet; and average speed of tracing. The results show a trade-off between speed and quality for the tablet parameters, with higher speed associated with more oscillations with respect to the reference lines, and lower number of strokes for each segment, in both male and female children. The involvement of visual–motor integration on the ability to reduce the oscillations in this tablet test was only seen for the male children, while both the male and female children showed a relationship between oscillations and more general/abstract visual–spatial processes. These data confirm the role of visual–motor processes in this figure-tracing tablet test only for male children, while more general visual–spatial processes influence the performance in the tablet test for both sexes. We conclude that the test proposed is useful to screen for grapho-motor difficulties. PMID:27803678

Credentialing of radiotherapy centres in Australasia for TROG 09.02 (Chisel), a Phase III clinical trial on stereotactic ablative body radiotherapy of early stage lung cancer.

PubMed

Kron, Tomas; Chesson, Brent; Hardcastle, Nicholas; Crain, Melissa; Clements, Natalie; Burns, Mark; Ball, David

2018-05-01

A randomised clinical trial comparing stereotactic ablative body radiotherapy (SABR) with conventional radiotherapy for early stage lung cancer has been conducted in Australia and New Zealand under the auspices of the TransTasman Radiation Oncology Group (NCT01014130). We report on the technical credentialing program as prerequisite for centres joining the trial. Participating centres were asked to develop treatment plans for two test cases to assess their ability to create plans according to protocol. Dose delivery in the presence of inhomogeneity and motion was assessed during a site visit using a phantom with moving inserts. Site visits for the trial were conducted in 16 Australian and 3 New Zealand radiotherapy facilities. The tests with low density inhomogeneities confirmed shortcomings of the AAA algorithm for dose calculation. Dose was assessed for a typical treatment delivery including at least one non-coplanar beam in a stationary and moving phantom. This end-to-end test confirmed that all participating centres were able to deliver stereotactic ablative body radiotherapy with the required accuracy while the planning study demonstrated that they were able to produce acceptable plans for both test cases. The credentialing process documented that participating centres were able to deliver dose as required in the trial protocol. It also gave an opportunity to provide education about the trial and discuss technical issues such as four-dimensional CT, small field dosimetry and patient immobilisation with staff in participating centres. Advances in knowledge: Credentialing is an important quality assurance tool for radiotherapy trials using advanced technology. In addition to confirming technical competence, it provides an opportunity for education and discussion about the trial.

Evaluation of high-efficiency gas-liquid contactors for natural gas processing. Second semiannual technical progress report, April 1, 1993--September 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-12-01

The objective of this proposed program is to evaluate the potential of rotating gas-liquid contactors for natural gas processing by expanding the currently available database. This expansion will focus on application of this technology to environments representative of those typically encountered in natural gas processing plants. Operational and reliability concerns will be addressed while generating pertinent engineering data relating to the mass-transfer process. Work to be performed this reporting period are: complete all negotiations and processing of agreements; complete assembly, modifications, shakedown, and conduct fluid dynamic studies using the plastic rotary contactor unit; confirmation of project test matrix; and locate,more » and transport an amine plant and dehydration plant. Accomplishment for this period are presented.« less

An optimal method for phosphorylation of rare earth chlorides in LiCl-KCl eutectic based waste salt

NASA Astrophysics Data System (ADS)

Eun, H. C.; Kim, J. H.; Cho, Y. Z.; Choi, J. H.; Lee, T. K.; Park, H. S.; Park, G. I.

2013-11-01

A study on an optimal method for the phosphorylation of rare earth chlorides in LiCl-KCl eutectic waste salt generated the pyrochemical process of spent nuclear fuel was performed. A reactor with a pitched four blade impeller was designed to create a homogeneous mixing zone in LiCl-KCl eutectic salt. A phosphorylation test of NdCl3 in the salt was carried out by changing the operation conditions (operation temperature, stirring rate, agent injection amount). Based on the results of the test, a proper operation condition (450 °C, 300 rpm, 1 eq. of phosphorylation agent) for over a 0.99 conversion ratio of NdCl3 to NdPO4 was determined. Under this condition, multi-component rare earth (La, Ce, Pr, Nd, Sm, Eu, Gd, Y) chlorides were effectively converted into phosphate forms. It was confirmed that the existing regeneration process of LiCl-KCl eutectic waste salt can be greatly improved and simplified through these phosphorylation test results.

Leaching of biocides used in façade coatings under laboratory test conditions.

PubMed

Schoknecht, Ute; Gruycheva, Jana; Mathies, Helena; Bergmann, Hannelore; Burkhardt, Michael

2009-12-15

The European Biocidal Products Directive 98/8/EC requires a risk assessment concerning possible effects of active ingredients on the environment. Biocides can be leached from treated materials exposed to outdoor use. These emissions have to be estimated and evaluated during the authorization procedure. Different immersion and irrigation tests were performed to investigate leaching of biocides from façade coatings. Several marketed formulations of textured coatings and paints spiked with a mixture of commonly used active ingredients (OIT, DCOIT, IPBC, carbendazim, isoproturon, diuron, terbutryn, and Irgarol 1051) were investigated. The emission process can be described by time-dependent functions that depend on the test conditions. The results of all test procedures confirm that leachability is related to water solubility and n-octanol-water partition coefficient of the active ingredients and that leaching of biocides from façade coatings is mainly a diffusion controlled process. Other factors like the composition of the product, availability and transport of water, concentration of active ingredients in the coatings, as well as UV-exposure of the coatings influence biocide emissions.

Development and validation of the trait and state versions of the Post-Event Processing Inventory.

PubMed

Blackie, Rebecca A; Kocovski, Nancy L

2017-03-01

Post-event processing (PEP) refers to negative and prolonged rumination following anxiety-provoking social situations. Although there are scales to assess PEP, they are situation-specific, some targeting only public-speaking situations. Furthermore, there are no trait measures to assess the tendency to engage in PEP. The purpose of this research was to create a new measure of PEP, the Post-Event Processing Inventory (PEPI), which can be employed following all types of social situations and includes both trait and state forms. Over two studies (study 1, N = 220; study 2, N = 199), we explored and confirmed the factor structure of the scale with student samples. For each form of the scale, we found and confirmed that a higher-order, general PEP factor could be inferred from three sub-domains (intensity, frequency, and self-judgment). We also found preliminary evidence for the convergent, concurrent, discriminant/divergent, incremental, and predictive validity for each version of the scale. Both forms of the scale demonstrated excellent internal consistency and the trait form had excellent two-week test-retest reliability. Given the utility and versatility of the scale, the PEPI may provide a useful alternative to existing measures of PEP and rumination.

Optimization and Surface Modification of Al-6351 Alloy Using SiC-Cu Green Compact Electrode by Electro Discharge Coating Process

NASA Astrophysics Data System (ADS)

Chakraborty, Sujoy; Kar, Siddhartha; Dey, Vidyut; Ghosh, Subrata Kumar

2017-06-01

This paper introduces the surface modification of Al-6351 alloy by green compact SiC-Cu electrode using electro-discharge coating (EDC) process. A Taguchi L-16 orthogonal array is employed to investigate the process by varying tool parameters like composition and compaction load and electro-discharge machining (EDM) parameters like pulse-on time and peak current. Material deposition rate (MDR), tool wear rate (TWR) and surface roughness (SR) are measured on the coated specimens. An optimum condition is achieved by formulating overall evaluation criteria (OEC), which combines multi-objective task into a single index. The signal-to-noise (S/N) ratio, and the analysis of variance (ANOVA) is employed to investigate the effect of relevant process parameters. A confirmation test is conducted based on optimal process parameters and experimental results are provided to illustrate the effectiveness of this approach. The modified surface is characterized by optical microscope and X-ray diffraction (XRD) analysis. XRD analysis of the deposited layer confirmed the transfer of tool materials to the work surface and formation of inter-metallic phases. The micro-hardness of the resulting composite layer is also measured which is 1.5-3 times more than work material’s one and highest layer thickness (LT) of 83.644μm has been successfully achieved.

Certification of windshear performance with RTCA class D radomes

NASA Technical Reports Server (NTRS)

Mathews, Bruce D.; Miller, Fran; Rittenhouse, Kirk; Barnett, Lee; Rowe, William

1994-01-01

Superposition testing of detection range performance forms a digital signal for input into a simulation of signal and data processing equipment and algorithms to be employed in a sensor system for advanced warning of hazardous windshear. For suitable pulse-Doppler radar, recording of the digital data at the input to the digital signal processor furnishes a realistic operational scenario and environmentally responsive clutter signal including all sidelobe clutter, ground moving target indications (GMTI), and large signal spurious due to mainbeam clutter and/or RFI respective of the urban airport clutter and aircraft scenarios (approach and landing antenna pointing). For linear radar system processes, a signal at the same point in the process from a hazard phenomena may be calculated from models of the scattering phenomena, for example, as represented in fine 3 dimensional reflectivity and velocity grid structures. Superposition testing furnishes a competing signal environment for detection and warning time performance confirmation of phenomena uncontrollable in a natural environment.

Lightening the load: perceptual load impairs visual detection in typical adults but not in autism.

PubMed

Remington, Anna M; Swettenham, John G; Lavie, Nilli

2012-05-01

Autism spectrum disorder (ASD) research portrays a mixed picture of attentional abilities with demonstrations of enhancements (e.g., superior visual search) and deficits (e.g., higher distractibility). Here we test a potential resolution derived from the Load Theory of Attention (e.g., Lavie, 2005). In Load Theory, distractor processing depends on the perceptual load of the task and as such can only be eliminated under high load that engages full capacity. We hypothesize that ASD involves enhanced perceptual capacity, leading to the superior performance and increased distractor processing previously reported. Using a signal-detection paradigm, we test this directly and demonstrate that, under higher levels of load, perceptual sensitivity was reduced in typical adults but not in adults with ASD. These findings confirm our hypothesis and offer a promising solution to the previous discrepancies by suggesting that increased distractor processing in ASD results not from a filtering deficit but from enhanced perceptual capacity.

Q Fever Outbreak among Workers at a Waste-Sorting Plant

PubMed Central

Alonso, Eva; Lopez-Etxaniz, Idoia; Hurtado, Ana; Liendo, Paloma; Urbaneja, Felix; Aspiritxaga, Inmaculada; Olaizola, Jose Ignacio; Piñero, Alvaro; Arrazola, Iñaki; Barandika, Jesús F.; Hernáez, Silvia; Muniozguren, Nerea; García- Pérez, Ana L.

2015-01-01

An outbreak of Q fever occurred in February–April 2014 among workers at a waste-sorting plant in Bilbao (Spain). The outbreak affected 58.5% of investigated employees, 47.2% as confirmed cases (PCR and/or serology) and 11.3% as probable cases (symptoms without laboratory confirmation). Only employees who had no-access to the waste processing areas of the plant were not affected and incidence of infection was significantly higher among workers not using respiratory protection masks. Detection by qPCR of Coxiella burnetii in dust collected from surfaces of the plant facilities confirmed exposure of workers inside the plant. Animal remains sporadically detected among the residues received for waste-sorting were the most probable source of infection. After cleaning and disinfection, all environmental samples tested negative. Personal protection measures were reinforced and made compulsory for the staff and actions were taken to raise farmers’ awareness of the biological risk of discharging animal carcasses as urban waste. PMID:26398249

Germline mosaicism of PHOX2B mutation accounts for familial recurrence of congenital central hypoventilation syndrome (CCHS).

PubMed

Rand, Casey M; Yu, Min; Jennings, Lawrence J; Panesar, Kelvin; Berry-Kravis, Elizabeth M; Zhou, Lili; Weese-Mayer, Debra E

2012-09-01

Congenital central hypoventilation syndrome (CCHS), a rare disorder characterized by alveolar hypoventilation and autonomic dysregulation, is caused by mutations in the PHOX2B gene. Most mutations occur de novo, but recent evidence suggests that up to 25% are inherited from asymptomatic parents with somatic mosaicism for these mutations. However, to date, germline mosaicism has not been reported. This report describes a family with recurrence of PHOX2B mutation-confirmed CCHS due to germline mosaicism. The first occurrence was a baby girl, noted on day 2 of life to have multiple episodes of apnea, bradycardia, and cyanosis while breathing room air. PHOX2B gene testing confirmed the diagnosis of CCHS with a heterozygous polyalanine repeat expansion mutation (PARM); genotype 20/27 (normal 20/20). Both parents tested negative for this mutation using fragment analysis (limit of detection<1%). Upon subsequent pregnancy [paternity confirmed using short tandem repeat (STR) analysis], amniocentesis testing identified the PHOX2B 20/27 genotype, confirmed with repeat testing. Elective abortion was performed at 21.5 weeks gestation. Testing of abortus tissue confirmed amniocentesis testing. The PHOX2B 20/27 expansion was not observed in a paternal sperm sample. This case represents the first reported family with recurrence of PHOX2B mutation-confirmed CCHS without detection of a parental carrier state or mosaicism, confirming the previously hypothesized possibility of germline mosaicism for PHOX2B mutations. This is an important finding for genetic counseling of CCHS families, suggesting that even if somatic mosaicism is not detected in parental samples, there is still reason for careful genetic counseling and consideration of prenatal testing during subsequent pregnancies. Copyright © 2012 Wiley Periodicals, Inc.

Analysis of current driving capability of pentacene TFTs for OLEDs

NASA Astrophysics Data System (ADS)

Ryu, Gi Seong; Byun, Hyun Sook; Xu, Yong Xian; Pyo, Kyung Soo; Choe, Ki Beom; Song, Chung Kun

2005-01-01

The flexible display and the application of Roll-To-Roll process is difficult because high temperature process of a-Si;H TFT and poly-Si TFT limited the use of plastic substrate. We proposed AMOLED using Pentacene TFT (OTFT) to fabricate flexible display. The first stage for OTFT application to OLED, we analyzed OTFT as driving device of OLED. The process performed on glass and plastic (PET) substrate that is coated ITO and PVP is used for gate insulator. The field effect mobility of the fabricated OTFT is 0.1~0.3cm2/V"sec and Ion/Ioff current ratio is 103~105. OLED is fabricated with two stories structure of TPD and Alq3, and we can observe the light at 5V by the naked eye. The wavelength of observed lights is 530nm ~550nm. We can confirm the driving of OLED due to OTFT using Test panel and observe OLED control by gate voltage of OTFT. Also, we verify designed structure and process, and make a demonstration fabricating 64 by 64 backplane based on Test panel.

Advanced oxidation of commercial herbicides mixture: experimental design and phytotoxicity evaluation.

PubMed

López, Alejandro; Coll, Andrea; Lescano, Maia; Zalazar, Cristina

2017-05-05

In this work, the suitability of the UV/H 2 O 2 process for commercial herbicides mixture degradation was studied. Glyphosate, the herbicide most widely used in the world, was mixed with other herbicides that have residual activity as 2,4-D and atrazine. Modeling of the process response related to specific operating conditions like initial pH and initial H 2 O 2 to total organic carbon molar ratio was assessed by the response surface methodology (RSM). Results have shown that second-order polynomial regression model could well describe and predict the system behavior within the tested experimental region. It also correctly explained the variability in the experimental data. Experimental values were in good agreement with the modeled ones confirming the significance of the model and highlighting the success of RSM for UV/H 2 O 2 process modeling. Phytotoxicity evolution throughout the photolytic degradation process was checked through germination tests indicating that the phytotoxicity of the herbicides mixture was significantly reduced after the treatment. The end point for the treatment at the operating conditions for maximum TOC conversion was also identified.

An approach to the patient with late-onset cerebellar ataxia.

PubMed

Fogel, Brent L; Perlman, Susan

2006-11-01

An 83-year-old man presented with hypertension, hyperlipidemia, and a previous basal cell carcinoma, having developed progressive worsening of his balance and difficulty walking at the age of 78 years. He was initially diagnosed with stroke, but MRI revealed only isolated cerebellar atrophy. The patient then underwent multiple evaluations for an underlying paraneoplastic process, all of which were negative, but his symptoms progressed and he remained undiagnosed for several years. Neurological examination, laboratory blood tests, MRI, and directed genetic testing. Five years after becoming symptomatic, the patient was re-evaluated for a possible genetic ataxia syndrome, which was subsequently confirmed by gene testing as spinocerebellar ataxia type 6 (SCA6). Symptomatic medical treatment and physical, occupational, and speech therapy.

Quantitation of Staphylococcus aureus in Seawater Using CHROMagar™ SA

PubMed Central

Pombo, David; Hui, Jennifer; Kurano, Michelle; Bankowski, Matthew J; Seifried, Steven E

2010-01-01

A microbiological algorithm has been developed to analyze beach water samples for the determination of viable colony forming units (CFU) of Staphylococcus aureus (S. aureus). Membrane filtration enumeration of S. aureus from recreational beach waters using the chromogenic media CHROMagar™SA alone yields a positive predictive value (PPV) of 70%. Presumptive CHROMagar™SA colonies were confirmed as S. aureus by 24-hour tube coagulase test. Combined, these two tests yield a PPV of 100%. This algorithm enables accurate quantitation of S. aureus in seawater in 72 hours and could support risk-prediction processes for recreational waters. A more rapid protocol, utilizing a 4-hour tube coagulase confirmatory test, enables a 48-hour turnaround time with a modest false negative rate of less than 10%. PMID:20222490

Discordant HIV Test Results: Implications on Perinatal and Haemotransfusion Screening for HIV Infection, Cape Coast, Ghana.

PubMed

Tetteh, Ato Kwamena; Agyarko, Edward

2017-01-01

Screening results of 488 pregnant women aged 15-44 years whose blood samples had been tested on-site, using First Response® HIV 1/2, and confirmed with INNO-LIA™ HIV I/II Score were used. Of this total, 178 were reactive (HIV I, 154; HIV II, 2; and HIV I and HIV II, 22). Of the 154 HIV I-reactive samples, 104 were confirmed to be HIV I-positive and 2 were confirmed to be HIV II-positive, while 48 were confirmed to be negative [false positive rate = 17.44% (13.56-21.32)]. The two HIV II samples submitted were confirmed to be negative with the confirmatory test. For the 22 HIV I and HIV II samples, 7 were confirmed to be HIV I-positive and 1 was confirmed to be HIV I- and HIV II-positive, while 14 were confirmed to be negative. Of the 310 nonreactive samples, 6 were confirmed to be HIV I-positive and 1 was confirmed to be HIV II-positive [false negative rate = 5.79% (1.63-8.38)], while 303 were negative. False negative outcomes will remain unconfirmed, with no management options for the client. False negative rate of 5.79% requires attention, as its resultant implications on control of HIV/AIDS could be dire.

Literature review for oxalate oxidation processes and plutonium oxalate solubility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nash, C. A.

2015-10-01

A literature review of oxalate oxidation processes finds that manganese(II)-catalyzed nitric acid oxidation of oxalate in precipitate filtrate is a viable and well-documented process. The process has been operated on the large scale at Savannah River in the past, including oxidation of 20 tons of oxalic acid in F-Canyon. Research data under a variety of conditions show the process to be robust. This process is recommended for oxalate destruction in H-Canyon in the upcoming program to produce feed for the MOX facility. Prevention of plutonium oxalate precipitation in filtrate can be achieved by concentrated nitric acid/ferric nitrate sequestration of oxalate.more » Organic complexants do not appear practical to sequester plutonium. Testing is proposed to confirm the literature and calculation findings of this review at projected operating conditions for the upcoming campaign.« less

75 FR 57200 - National Poultry Improvement Plan and Auxiliary Provisions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-20

... (ELISA) test to confirm the positive results of other serological tests. We are proposing to remove the ELISA test from this list. The ELISA test is a screening assay and should not be used to confirm... status is negative for Mycoplasma. We would amend this paragraph to include the ELISA and the official...

Culture confirmation of tuberculosis cases in Birmingham, UK.

PubMed

Hayer, Kalbir S; Sitch, Alice J; Dedicoat, Martin; Wood, Annette L

2013-10-01

The proportion of culture-confirmed tuberculosis (TB) cases in Birmingham had gradually decreased to less than 65% in 2008. Reasons for this were unclear, therefore this study assessed diagnostic methods used for confirming TB and reviewed factors involved in positive culture. A cross-sectional study was carried out. A list of notified TB cases for Birmingham in those aged 16 y and over in 2009 was collated. Where no positive culture was recorded, further data were collected from hospital databases and case notes. Of 449 TB cases, 419 (93%) had samples taken for culture testing. Of all cases, 309 (69%) were confirmed by culture testing; of those receiving culture testing, 73% were confirmed. Pulmonary TB was identified as a predictor of positive culture in both the unadjusted and adjusted analyses: odds ratio (OR) 2.05, 95% confidence interval (CI) 1.32-3.19, and OR 2.32, 95% CI 1.29-4.17, respectively. Gender, age, ethnicity, UK born, and treatment delay were not significantly associated with positive culture. Of 140 cases not confirmed by culture, 129 (92%) had their diagnosis supported by at least one other test. The vast majority of TB cases had microbiological specimens taken to help confirm the disease. Furthermore, culture confirmation rates in Birmingham were meeting national targets in 2009. However culture confirmation rates were significantly lower in extrapulmonary TB, therefore further work is suggested in this group. The role of other investigations (e.g. interferon-gamma release assay (IGRA), Mantoux) is unclear. Further collaboration between clinicians, histopathologists, and microbiologists is advised to ensure samples are sent appropriately and culture confirmation is optimized.

Space Shuttle Main Engine Low Pressure Oxidizer Turbo-Pump Inducer Dynamic Environment Characterization through Water Model and Hot-Fire Testing

NASA Technical Reports Server (NTRS)

Arellano, Patrick; Patton, Marc; Schwartz, Alan; Stanton, David

2006-01-01

The Low Pressure Oxidizer Turbopump (LPOTP) inducer on the Block II configuration Space Shuttle Main Engine (SSME) experienced blade leading edge ripples during hot firing. This undesirable condition led to a minor redesign of the inducer blades. This resulted in the need to evaluate the performance and the dynamic environment of the redesign, relative to the current configuration, as part of the design acceptance process. Sub-scale water model tests of the two inducer configurations were performed, with emphasis on the dynamic environment due to cavitation induced vibrations. Water model tests were performed over a wide range of inlet flow coefficient and pressure conditions, representative of the scaled operating envelope of the Block II SSME, both in flight and in ground hot-fire tests, including all power levels. The water test hardware, facility set-up, type and placement of instrumentation, the scope of the test program, specific test objectives, data evaluation process and water test results that characterize and compare the two SSME LPOTP inducers are discussed. In addition, dynamic characteristics of the two water models were compared to hot fire data from specially instrumented ground tests. In general, good agreement between the water model and hot fire data was found, which confirms the value of water model testing for dynamic characterization of rocket engine turbomachinery.

Double Blind Test For Bio-Stimulation Effects On Pain Relief By Diode Laser

NASA Astrophysics Data System (ADS)

Saeki, Norio; Sembokuya, Iwajiro; Arakawa, Kazuo; Fujimasa, Iwao; Mabuchi, Kunihiko; Abe, Yuusuke; Atsumi, Kazuhiko

1989-09-01

The bio-stimulation effect of semiconductor laser on therapeutic pain relief was investigated by conducting a double blind test performed on more than one hundred patient subjects suffering from various neualgia. A compact laser therapeutic equipment with two laser probes each having 60 mW power was developed and utilized for the experiment. Each probe was driven by either the active or the dummy source selected randomly, and its results were stored in the memory for statistical processing. The therapeutic treatments including active and dummy treatments were performed on 102 subjects. The pain relief effects were confirmed for 85.5% of the subjects.

Development of ECT/UT inspection system for bottom mounted instrumentation nozzle of PWR reactor vessels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, H.; Fukui, S.; Iwahashi, Y.

1994-12-31

The development of inspection technique and tool for Bottom Mounted Instrument (BMI) nozzle of PWR plant was performed for countermeasure of leakage accident at incore instrument nozzle of Hamaoka-1 (BWR). MHI achieved the following development, of which object was PWR Plant R/V: (1) development of ECT/UT Multi-sensored Probe; (2) development of Inspection System (3) development of Data Processing System. The Inspection System had been functionally tested using full scale mock-up. As the result of the functional test, this system was confirmed to be very effective, and assumed to be hopeful for the actual application on site.

Forecasting volatility with neural regression: a contribution to model adequacy.

PubMed

Refenes, A N; Holt, W T

2001-01-01

Neural nets' usefulness for forecasting is limited by problems of overfitting and the lack of rigorous procedures for model identification, selection and adequacy testing. This paper describes a methodology for neural model misspecification testing. We introduce a generalization of the Durbin-Watson statistic for neural regression and discuss the general issues of misspecification testing using residual analysis. We derive a generalized influence matrix for neural estimators which enables us to evaluate the distribution of the statistic. We deploy Monte Carlo simulation to compare the power of the test for neural and linear regressors. While residual testing is not a sufficient condition for model adequacy, it is nevertheless a necessary condition to demonstrate that the model is a good approximation to the data generating process, particularly as neural-network estimation procedures are susceptible to partial convergence. The work is also an important step toward developing rigorous procedures for neural model identification, selection and adequacy testing which have started to appear in the literature. We demonstrate its applicability in the nontrivial problem of forecasting implied volatility innovations using high-frequency stock index options. Each step of the model building process is validated using statistical tests to verify variable significance and model adequacy with the results confirming the presence of nonlinear relationships in implied volatility innovations.

Confirming and denying in co-construction processes: a case study of an adult with cerebral palsy and two familiar partners.

PubMed

Hörmeyer, Ina; Renner, Gregor

2013-09-01

For individuals with complex communication needs, one of the most frequent communicative strategies is the co-construction of meaning with familiar partners. This preliminary single-case study gives insight into a special sequential pattern of co-construction processes - the search sequence - particularly in relation to the processes of confirming and denying meanings proposed by familiar interaction partners. Five different conversations between an adult with cerebral palsy and complex communication needs and two familiar co-participants were videotaped and analyzed using the methodology of conversation analysis (CA). The study revealed that confirmations and denials are not simply two alternative actions, but that several possibilities to realize confirmations and denials exist that differ in their frequency and that have different consequences for the sequential context. This study of confirmations and denials demonstrates that co-construction processes are more complex than have previously been documented.

Evaluation of Petrifilm Lactic Acid Bacteria Plates for Counting Lactic Acid Bacteria in Food.

PubMed

Kanagawa, Satomi; Ohshima, Chihiro; Takahashi, Hajime; Burenqiqige; Kikuchi, Misato; Sato, Fumina; Nakamura, Ayaka; Mohamed, Shimaa M; Kuda, Takashi; Kimura, Bon

2018-06-01

Although lactic acid bacteria (LAB) are used widely as starter cultures in the production of fermented foods, they are also responsible for food decay and deterioration. The undesirable growth of LAB in food causes spoilage, discoloration, and slime formation. Because of these adverse effects, food companies test for the presence of LAB in production areas and processed foods and consistently monitor the behavior of these bacteria. The 3M Petrifilm LAB Count Plates have recently been launched as a time-saving and simple-to-use plate designed for detecting and quantifying LAB. This study compares the abilities of Petrifilm LAB Count Plates and the de Man Rogosa Sharpe (MRS) agar medium to determine the LAB count in a variety of foods and swab samples collected from a food production area. Bacterial strains isolated from Petrifilm LAB Count Plates were identified by 16S rDNA sequence analysis to confirm the specificity of these plates for LAB. The results showed no significant difference in bacterial counts measured by using Petrifilm LAB Count Plates and MRS medium. Furthermore, all colonies growing on Petrifilm LAB Count Plates were confirmed to be LAB, while yeast colonies also formed in MRS medium. Petrifilm LAB Count Plates eliminated the plate preparation and plate inoculation steps, and the cultures could be started as soon as a diluted food sample was available. Food companies are required to establish quality controls and perform tests to check the quality of food products; the use of Petrifilm LAB Count Plates can simplify this testing process for food companies.

Cognitive bias in back pain patients attending osteopathy: testing the enmeshment model in reference to future thinking.

PubMed

Read, Jessica; Pincus, Tamar

2004-12-01

Depressive symptoms are common in chronic pain. Previous research has found differences in information-processing biases in depressed pain patients and depressed people without pain. The schema enmeshment model of pain (SEMP) has been proposed to explain chronic pain patients' information-processing biases. Negative future thinking is common in depression but has not been explored in relation to chronic pain and information-processing models. The study aimed to test the SEMP with reference to future thinking. An information-processing paradigm compared endorsement and recall bias between depressed and non-depressed chronic low back pain patients and control participants. Twenty-five depressed and 35 non-depressed chronic low back pain patients and 25 control participants (student osteopaths) were recruited from an osteopathy practice. Participants were asked to endorse positive and negative ill-health, depression-related, and neutral (control) adjectives, encoded in reference to either current or future time-frame. Incidental recall of the adjectives was then tested. While the expected hypothesis of a recall bias by depressed pain patients towards ill-health stimuli in the current condition was confirmed, the recall bias was not present in the future condition. Additionally, patterns of endorsement and recall bias differed. Results extend understanding of future thinking in chronic pain within the context of the SEMP.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washiya, Tadahiro; Komaki, Jun; Funasaka, Hideyuki

Japan Atomic Energy Agency (JAEA) has been developing the new aqueous reprocessing system named 'NEXT' (New Extraction system for TRU recovery)1-2, which provides many advantages as waste volume reduction, cost savings by advanced components and simplification of process operation. Advanced head-end systems in the 'NEXT' process consist of fuel disassembly system, fuel shearing system and continuous dissolver system. We developed reliable fuel disassembly system with innovative procedure, and short-length shearing system and continuous dissolver system can be provided highly concentrated dissolution to adapt to the uranium crystallization process. We have carried out experimental studies, and fabrication of engineering-scale test devicesmore » to confirm the systems performance. In this paper, research and development of advanced head-end systems are described. (authors)« less

16 CFR 1633.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... confirmation test on the mattress set it manufactures. (r) Confirmation test means a pre-market test conducted... included; examples are convertible sofa bed mattresses, corner group mattresses, day bed mattresses, roll...) This term includes any one, or any combination of the following: replacing the ticking or batting...

16 CFR 1633.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... confirmation test on the mattress set it manufactures. (r) Confirmation test means a pre-market test conducted... included; examples are convertible sofa bed mattresses, corner group mattresses, day bed mattresses, roll...) This term includes any one, or any combination of the following: replacing the ticking or batting...

16 CFR 1633.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... confirmation test on the mattress set it manufactures. (r) Confirmation test means a pre-market test conducted... included; examples are convertible sofa bed mattresses, corner group mattresses, day bed mattresses, roll...) This term includes any one, or any combination of the following: replacing the ticking or batting...

16 CFR 1633.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... confirmation test on the mattress set it manufactures. (r) Confirmation test means a pre-market test conducted... included; examples are convertible sofa bed mattresses, corner group mattresses, day bed mattresses, roll...) This term includes any one, or any combination of the following: replacing the ticking or batting...

16 CFR § 1633.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... confirmation test on the mattress set it manufactures. (r) Confirmation test means a pre-market test conducted... included; examples are convertible sofa bed mattresses, corner group mattresses, day bed mattresses, roll...) This term includes any one, or any combination of the following: replacing the ticking or batting...

The trigger card system for the MAJORANA DEMONSTRATOR

NASA Astrophysics Data System (ADS)

Thompson, William; Anderson, John; Howe, Mark; Meijer, Sam; Wilkerson, John; Majorana Collaboration

2014-09-01

The aim of the MAJORANA DEMONSTRATOR is to demonstrate the feasibility of providing low enough background levels to search for neutrinoless double-beta decay (0 νββ) in an array of germanium detectors enriched to 87% in 76Ge. Currently, it is unknown if this decay process occurs; however, observation of such a decay process would show that lepton number is violated, confirm that neutrinos are Majorana particles, and yield information on the absolute mass scale of the neutrino. With current experimental results indicating a half-life greater than 2 x 1025 years for this decay, the minimization of background events is of critical importance. Utilizing time correlation, coincidence testing is able to reject multi-detector events that may otherwise be mistaken for 0 νββ when viewed independently. Here, we present both the hardware and software of the trigger card system, which provides a common clock to all digitizers and the muon veto system, thereby enabling the rejection of background events through coincidence testing. Current experimental results demonstrate the accuracy of the distributed clock to be within two clock pulses (20 ns) across all system components. A test system is used to validate the data acquisition system. The aim of the MAJORANA DEMONSTRATOR is to demonstrate the feasibility of providing low enough background levels to search for neutrinoless double-beta decay (0 νββ) in an array of germanium detectors enriched to 87% in 76Ge. Currently, it is unknown if this decay process occurs; however, observation of such a decay process would show that lepton number is violated, confirm that neutrinos are Majorana particles, and yield information on the absolute mass scale of the neutrino. With current experimental results indicating a half-life greater than 2 x 1025 years for this decay, the minimization of background events is of critical importance. Utilizing time correlation, coincidence testing is able to reject multi-detector events that may otherwise be mistaken for 0 νββ when viewed independently. Here, we present both the hardware and software of the trigger card system, which provides a common clock to all digitizers and the muon veto system, thereby enabling the rejection of background events through coincidence testing. Current experimental results demonstrate the accuracy of the distributed clock to be within two clock pulses (20 ns) across all system components. A test system is used to validate the data acquisition system. We acknowledge support from the Office of Nuclear Physics in the DOE Office of Science, the Particle Astrophysics and REU Programs of the NSF, and the Sanford Underground Research Laboratory.

Recovery Act. Direct Confirmation of Commercial Geothermal Resources in Colorado Using Remote Sensing and On-Site Exploration, Testing, and Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foley, Paul; Skeehan, Kirsten; Smith, Jerome

Report on the confirmation of Commercial Geothermal Resources in Colorado describing the on site testing and analysis to confirm remote sensing identified potential resources. A series of thermal gradient wells were drilled in the Pagosa Springs region and the data collected is analyzed within.

Synthesis and characterization of graphene quantum dots-silver nanocomposites

NASA Astrophysics Data System (ADS)

Vandana, M.; Ashokkumar, S. P.; Vijeth, H.; Niranjana, M.; Yesappa, L.; Devendrappa, H.

2018-04-01

A facile microwave assisted hydrothermal method is used to synthesise glucose derived water soluble crystalline graphene quantum dots (GQDs) andcitrate reduction method was used to synthesized silver nanoparticles (SNPs). The formation of graphene quantum dots-silver nanocomposites (GSC) was synthesized through a simple refluxing process and characterised using Fourier Transform Infrared (FT-IR) to study the chemical interaction, Surface morphology using FESEM, Optical properties were studied using UV-Visible spectroscopy. The absorption band shows at 249, 306 and 447 nm confirms the formation of GQDs and GSC. The electrochemical performance of GSC tested to determine the oxidation/reduction processes by cyclic voltammetry and linear sweep voltammetry.

Characterization of failure processes in tungsten copper composites under fatigue loading conditions

NASA Technical Reports Server (NTRS)

Kim, Yong-Suk; Verrilli, Michael J.; Gabb, Timothy P.

1989-01-01

A fractographic and metallographic investigation was performed on specimens of a tungsten fiber reinforced copper matrix composite (9 vol percent), which had experienced fatigue failures at elevated temperatures. Major failure modes and possible failure mechanisms, with an emphasis placed on characterizing fatigue damage accumulation, were determined. Metallography of specimens fatigued under isothermal cyclic loading suggested that fatigue damage initiates in the matrix. Cracks nucleated within the copper matrix at grain boundaries, and they propagated through cavity coalescence. The growing cracks subsequently interacted with the reinforcing tungsten fibers, producing a localized ductile fiber failure. Examinations of interrupted tests before final failure confirmed the suggested fatigue damage processes.

Time reversibility of intracranial human EEG recordings in mesial temporal lobe epilepsy

NASA Astrophysics Data System (ADS)

van der Heyden, M. J.; Diks, C.; Pijn, J. P. M.; Velis, D. N.

1996-02-01

Intracranial electroencephalograms from patients suffering from mesial temporal lobe epilepsy were tested for time reversibility. If the recorded time series is irreversible, the input of the recording system cannot be a realisation of a linear Gaussian random process. We confirmed experimentally that the measurement equipment did not introduce irreversibility in the recorded output when the input was a realisation of a linear Gaussian random process. In general, the non-seizure recordings are reversible, whereas the seizure recordings are irreversible. These results suggest that time reversibility is a useful property for the characterisation of human intracranial EEG recordings in mesial temporal lobe epilepsy.

Separating and stabilizing phosphate from high-level radioactive waste: process development and spectroscopic monitoring.

PubMed

Lumetta, Gregg J; Braley, Jenifer C; Peterson, James M; Bryan, Samuel A; Levitskaia, Tatiana G

2012-06-05

Removing phosphate from alkaline high-level waste sludges at the Department of Energy's Hanford Site in Washington State is necessary to increase the waste loading in the borosilicate glass waste form that will be used to immobilize the highly radioactive fraction of these wastes. We are developing a process which first leaches phosphate from the high-level waste solids with aqueous sodium hydroxide, and then isolates the phosphate by precipitation with calcium oxide. Tests with actual tank waste confirmed that this process is an effective method of phosphate removal from the sludge and offers an additional option for managing the phosphorus in the Hanford tank waste solids. The presence of vibrationally active species, such as nitrate and phosphate ions, in the tank waste processing streams makes the phosphate removal process an ideal candidate for monitoring by Raman or infrared spectroscopic means. As a proof-of-principle demonstration, Raman and Fourier transform infrared (FTIR) spectra were acquired for all phases during a test of the process with actual tank waste. Quantitative determination of phosphate, nitrate, and sulfate in the liquid phases was achieved by Raman spectroscopy, demonstrating the applicability of Raman spectroscopy for the monitoring of these species in the tank waste process streams.

Linear landmark extraction in SAR images with application to augmented integrity aero-navigation: an overview to a novel processing chain

NASA Astrophysics Data System (ADS)

Fabbrini, L.; Messina, M.; Greco, M.; Pinelli, G.

2011-10-01

In the context of augmented integrity Inertial Navigation System (INS), recent technological developments have been focusing on landmark extraction from high-resolution synthetic aperture radar (SAR) images in order to retrieve aircraft position and attitude. The article puts forward a processing chain that can automatically detect linear landmarks on highresolution synthetic aperture radar (SAR) images and can be successfully exploited also in the context of augmented integrity INS. The processing chain uses constant false alarm rate (CFAR) edge detectors as the first step of the whole processing procedure. Our studies confirm that the ratio of averages (RoA) edge detector detects object boundaries more effectively than Student T-test and Wilcoxon-Mann-Whitney (WMW) test. Nevertheless, all these statistical edge detectors are sensitive to violation of the assumptions which underlie their theory. In addition to presenting a solution to the previous problem, we put forward a new post-processing algorithm useful to remove the main false alarms, to select the most probable edge position, to reconstruct broken edges and finally to vectorize them. SAR images from the "MSTAR clutter" dataset were used to prove the effectiveness of the proposed algorithms.

Advanced oxidation-based treatment of furniture industry wastewater.

PubMed

Tichonovas, Martynas; Krugly, Edvinas; Grybauskas, Arturas; Jankūnaitė, Dalia; Račys, Viktoras; Martuzevičius, Dainius

2017-07-16

The paper presents a study on the treatment of the furniture industry wastewater in a bench scale advanced oxidation reactor. The researched technology utilized a simultaneous application of ozone, ultraviolet radiation and surface-immobilized TiO 2 nanoparticle catalyst. Various combinations of processes were tested, including photolysis, photocatalysis, ozonation, catalytic ozonation, photolytic ozonation and photocatalytic ozonation were tested against the efficiency of degradation. The efficiency of the processes was primarily characterized by the total organic carbon (TOC) analysis, indicating the remaining organic material in the wastewater after the treatment, while the toxicity changes in wastewater were researched by Daphnia magna toxicity tests. Photocatalytic ozonation was confirmed as the most effective combination of processes (99.3% of TOC reduction during 180 min of treatment), also being the most energy efficient (4.49-7.83 MJ/g). Photocatalytic ozonation and photolytic ozonation remained efficient across a wide range of pH (3-9), but the pH was an important factor in photocatalysis. The toxicity of wastewater depended on the duration of the treatment: half treated water was highly toxic, while fully treated water did not possess any toxicity. Our results indicate that photocatalytic ozonation has a high potential for the upscaling and application in industrial settings.

Sputtered protective coatings for die casting dies

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Nieh, C.-Y.; Wallace, J. F.

1981-01-01

Three experimental research designs investigating candidate materials and processes involved in protective die surface coating procedures by sputter deposition, using ion beam technologies, are discussed. Various pre-test results show that none of the coatings remained completely intact for 15,000 test cycles. The longest lifetime was observed for coatings such as tungsten, platinum, and molybdenum which reduced thermal fatigue, but exhibited oxidation and suppressed crack initiation only as long as the coating did not fracture. Final test results confirmed earlier findings and coatings with Pt and W proved to be the candidate materials to be used on a die surface to increase die life. In the W-coated specimens, which remained intact on the surface after thermal fatigue testing, no oxidation was found under the coating, although a few cracks formed on the surface where the coating broke down. Further research is planned.

Obtaining of granular fertilizers based on ashes from combustion of waste residues and ground bones using phosphorous solubilization by bacteria Bacillus megaterium.

PubMed

Rolewicz, M; Rusek, P; Borowik, K

2018-06-15

The article presents research results on obtaining phosphorus granulated fertilizers on the basis of microbiologically activated sewage sludge ashes, ground bones and dried blood from meat industry. Granulation tests were carried out using a laboratory pan granulator as well as on an experimental pilot plant. The aim of the studies was to select the proper composition of the mixture of raw materials and binding agents to obtain granulated fertilizers from waste materials such as MSSA and MBM and bacteria lyophilisate. Obtained fertilizer samples were subjected to physical tests (granulation tests etc.) and quality assessment. The tests confirmed that it was possible to produce granulated phosphate fertilizers using the Bacillus megaterium for solubilization of phosphorus in a simple process. Copyright © 2017 Elsevier Ltd. All rights reserved.

HAS AN IMPORTANT TEST BEEN OVERLOOKED?: CLOSURE FLEXIBILITY IN SCHIZOPHRENIA

PubMed Central

Butler, Pamela D.; Schechter, Isaac; Revheim, Nadine; Silipo, Gail; Javitt, Daniel C.

2010-01-01

Deficits in visual processing are now recognized as a core feature of schizophrenia. In the 1940’s, Louis Thurstone developed a series of tests designed to evaluate specific aspects of visual perceptual processing including the Closure Flexibility Test (CFT), which was designed to measure “the ability to hold a configuration in mind despite distraction.” The present study evaluated patients’ performance on this task and its relationship to other tests of neuropsychological function, particularly to a measure of sustained visual attention. Thirty-nine patients with schizophrenia or schizoaffective disorder and 40 controls participated. The CFT was administered both in its original form (10 min) and also in a briefer form (3 min) in which only a portion of stimuli were given. Patients showed highly significant large effect size deficits on both the original (d=1.6) and brief (d=1.2) CFT. Between-group deficits in performance survived covariation for IQ. In addition, the CFT score was significantly related to performance on the MATRICS measure of attention/vigilance, the Continuous Performance Test-Identical Pairs version (CPT-IP). This correlation remained significant even after controlling for non-specific intercorrelations among neurocognitive measures. Results confirm the severity of early visual processing deficits in schizophrenia. In addition, the CFT is a brief, easy to administer alphabet-independent, paper-and-pencil test with established psychometric properties that may be useful as an index of the sustained visual attention construct in schizophrenia. PMID:20110157

CMOS serial link for fully duplexed data communication

NASA Astrophysics Data System (ADS)

Lee, Kyeongho; Kim, Sungjoon; Ahn, Gijung; Jeong, Deog-Kyoon

1995-04-01

This paper describes a CMOS serial link allowing fully duplexed 500 Mbaud serial data communication. The CMOS serial link is a robust and low-cost solution to high data rate requirements. A central charge pump PLL for generating multiphase clocks for oversampling is shared by several serial link channels. Fully duplexed serial data communication is realized in the bidirectional bridge by separating incoming data from the mixed signal on the cable end. The digital PLL accomplishes process-independent data recovery by using a low-ratio oversampling, a majority voting, and a parallel data recovery scheme. Mostly, digital approach could extend its bandwidth further with scaled CMOS technology. A single channel serial link and a charge pump PLL are integrated in a test chip using 1.2 micron CMOS process technology. The test chip confirms upto 500 Mbaud unidirectional mode operation and 320 Mbaud fully duplexed mode operation with pseudo random data patterns.

Detailed results of ASTP experiment MA-011. [biological processing facility in space

NASA Technical Reports Server (NTRS)

Seaman, G. V. F.; Allen, R. E.; Barlow, G. H.; Bier, M.

1976-01-01

This experiment was developed in order to conduct engineering and operational tests of electrokinetic equipment in a micro-gravity environment. The experimental hardware in general functioned as planned and electrophoretic separations were obtained in space. The results indicated the development of satisfactory sample collection, return, and preservation techniques. The application of a near-zero zeta potential interior wall coating to the experimental columns, confirmation of biocompatibility of all appropriate hardware components, and use of a sterile operating environment provided a significant step forward in the development of a biological processing facility in space. A separation of a test of aldehyde-fixed rabbit, human, and horse red blood cells was obtained. Human kidney cells were separated into several components and viable cells returned to earth. The isotachophoretic separation of red cells was also demonstrated. Problems associated with the hardware led to a lack of success in the attempt to separate subpopulations of human lymphocytes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Shuyu; Yu, Shifeng; Siedler, Michael

This study presented a power compensated MEMS differential scanning calorimeter (DSC) for protein stability characterization. In this microfabricated sensor, PDMS (Polydimethylsiloxane) and polyimide were used to construct the adiabatic chamber (1 μL) and temperature sensitive vanadium oxide was used as the thermistor material. A power compensation system was implemented to maintain the sample and reference at the same temperature. The resolution study and step response characterization indicated the high sensitivity (6 V/W) and low noise level (60 μk) of the device. The test with IgG1 antibody (mAb1) samples showed clear phase transitions and the data was confirmed to be reasonablemore » by comparing it with the results of commercial DSC’s test. Finally, this device used ~1uL sample amount and could complete the scanning process in 4 min, significantly increasing the throughput of the bimolecular thermodynamics study like drug formulation process.« less

A power compensated differential scanning calorimeter for protein stability characterization

DOE PAGES

Wang, Shuyu; Yu, Shifeng; Siedler, Michael; ...

2017-10-07

This study presented a power compensated MEMS differential scanning calorimeter (DSC) for protein stability characterization. In this microfabricated sensor, PDMS (Polydimethylsiloxane) and polyimide were used to construct the adiabatic chamber (1 μL) and temperature sensitive vanadium oxide was used as the thermistor material. A power compensation system was implemented to maintain the sample and reference at the same temperature. The resolution study and step response characterization indicated the high sensitivity (6 V/W) and low noise level (60 μk) of the device. The test with IgG1 antibody (mAb1) samples showed clear phase transitions and the data was confirmed to be reasonablemore » by comparing it with the results of commercial DSC’s test. Finally, this device used ~1uL sample amount and could complete the scanning process in 4 min, significantly increasing the throughput of the bimolecular thermodynamics study like drug formulation process.« less

Thermal stability of poly(3-hydroxybutyrate)/vegetable fiber composites

NASA Astrophysics Data System (ADS)

Cipriano, Pâmela Bento; de Sá, Mayelli Dantas; Andrade, André L. Simões; de Carvalho, Laura Hecker; Canedo, Eduardo Luis

2015-05-01

The present work deals with the thermal stability during and after processing of composites of poly(3-hydroxybutyrate) (PHB) - a fully biodegradable semi-crystalline thermoplastic obtained from renewable resources through low-impact biotechnological process, biocompatible and non-toxic - and vegetable fiber from the fruit (coconut) of babassu palm tree. PHB/babassu composites with 0, 5, 10 and 20% w/w load were prepared in a laboratory internal mixer. Two fractions of the mesocarp of babassu with different particle sizes were compounded with PHB and test specimens molded by compression. The effect of loading level and processing conditions on torque, temperature and mechanical energy dissipation were studied using a new engineering model. It was found that PHB degrades during processing at temperatures slightly above the melting point. To minimize thermal degradation stabilizer and chain extender additives were incorporated, with mixed results. These findings were confirmed by the dependence of the melt flow rate on the processing temperature.

VIDAS Listeria species Xpress (LSX).

PubMed

Johnson, Ronald; Mills, John

2013-01-01

The AOAC GovVal study compared the VIDAS Listeria species Xpress (LSX) to the Health Products and Food Branch MFHPB-30 reference method for detection of Listeria on stainless steel. The LSX method utilizes a novel and proprietary enrichment media, Listeria Xpress broth, enabling detection of Listeria species in environmental samples with the automated VIDAS in a minimum of 26 h. The LSX method also includes the use of the chromogenic media, chromID Ottaviani Agosti Agar (OAA) and chromID Lmono for confirmation of LSX presumptive results. In previous AOAC validation studies comparing VIDAS LSX to the U.S. Food and Drug Administration's Bacteriological Analytical Manual (FDA-BAM) and the U.S. Department of Agriculture-Food Safety and Inspection Service (USDA-FSIS) reference methods, the LSX method was approved as AOAC Official Method 2010.02 for the detection of Listeria species in dairy products, vegetables, seafood, raw meats and poultry, and processed meats and poultry, and as AOAC Performance Tested Method 100501 in a variety of foods and on environmental surfaces. The GovVal comparative study included 20 replicate test portions each at two contamination levels for stainless steel where fractionally positive results (5-15 positive results/20 replicate portions tested) were obtained by at least one method at one level. Five uncontaminated controls were included. In the stainless steel artificially contaminated surface study, there were 25 confirmed positives by the VIDAS LSX assay and 22 confirmed positives by the standard culture methods. Chi-square analysis indicated no statistical differences between the VIDAS LSX method and the MFHPB-30 standard methods at the 5% level of significance. Confirmation of presumptive LSX results with the chromogenic OAA and Lmono media was shown to be equivalent to the appropriate reference method agars. The data in this study demonstrate that the VIDAS LSX method is an acceptable alternative method to the MFHPB-30 standard culture method for the detection of Listeria species on stainless steel.

Thermomechanical simulations and experimental validation for high speed incremental forming

NASA Astrophysics Data System (ADS)

Ambrogio, Giuseppina; Gagliardi, Francesco; Filice, Luigino; Romero, Natalia

2016-10-01

Incremental sheet forming (ISF) consists in deforming only a small region of the workspace through a punch driven by a NC machine. The drawback of this process is its slowness. In this study, a high speed variant has been investigated from both numerical and experimental points of view. The aim has been the design of a FEM model able to perform the material behavior during the high speed process by defining a thermomechanical model. An experimental campaign has been performed by a CNC lathe with high speed to test process feasibility. The first results have shown how the material presents the same performance than in conventional speed ISF and, in some cases, better material behavior due to the temperature increment. An accurate numerical simulation has been performed to investigate the material behavior during the high speed process confirming substantially experimental evidence.

Detection of Listeria monocytogenes in pork and beef using the VIDAS® LMO2 automated enzyme linked immunoassay method.

PubMed

Meyer, Cornelia; Fredriksson-Ahomaa, Maria; Sperner, Brigitte; Märtlbauer, Erwin

2011-07-01

Listeria (L.) monocytogenes, a foodborne pathogen, is known to be a possible contaminant of foods during production and processing. Samples (n=985) of raw meat and by-products obtained from beef and pork were first screened by the VIDAS system for the presence of Listeria spp., followed by testing for the presence of L. monocytogenes. Positive L. monocytogenes results were confirmed by plating on selective agars: 14% of the samples were positive for Listeria and 4% tested positive for L. monocytogenes, of which 3% were confirmed on selective agars. In by-products (17%) the contamination with listeriae was higher than in meat cuts (10%). Only samples strongly positive for Listeria spp. by VIDAS were positive for L. monocytogenes. Overall, the prevalence of L. monocytogenes in beef and pork samples was rather low in comparison to most previous studies. The VIDAS system was shown to be a suitable method for screening out Listeria-negative samples; the main advantage being a markedly reduced assay time. Copyright © 2011 Elsevier Ltd. All rights reserved.

Anaphylactic shock following castor bean contact: a case report.

PubMed

Coattrenec, Y; Jaques, D; Jandus, P; Harr, T; Spoerl, D

2017-01-01

The castor bean plant, Ricinus communis , is known to have allergenic and toxic properties. Castor bean allergy has been described mainly as an occupational inhalation allergy in laboratory workers, in persons working in oil processing mills or in agricultural industry. So far, only one case of anaphylactic reaction due to castor bean sensitization confirmed by specific IgE has been described in literature. A 30-year-old woman presented to the emergency room with severe angioedema followed by urticaria, hypotension and tachycardia. She recovered after treatment with antihistamines, corticosteroids, nebulized adrenaline and intravenous fluids. Food induced anaphylaxis was excluded by allergological investigations. After repeated thorough history, the patient mentioned having bitten into a castor bean just before the reaction. Cutaneous test (prick-to-prick) and specific IgE for castor bean were highly positive. We report the second case of a severe anaphylactic reaction to castor beans, confirmed by IgE testing, reported in the literature. It underlines the importance of a meticulous history in allergology and highlights the fact, that castor beans may cause potentially fatal anaphylaxis.

Perovskite-nitrogen-doped carbon nanotube composite as bifunctional catalysts for rechargeable lithium-air batteries.

PubMed

Park, Hey Woong; Lee, Dong Un; Park, Moon Gyu; Ahmed, Raihan; Seo, Min Ho; Nazar, Linda F; Chen, Zhongwei

2015-03-01

Developing an effective bifunctional catalyst is a significant issue, as rechargeable metal-air batteries are very attractive for future energy systems. In this study, a facile one-pot process is introduced to prepare an advanced bifunctional catalyst (op-LN) incorporating nitrogen-doped carbon nanotubes (NCNTs) into perovskite La0.5 Sr0.5 Co0.8 Fe0.2 O3 nanoparticles (LSCF-NPs). Confirmed by half-cell testing, op-LN exhibits synergistic effects of LSCF-NP and NCNT with excellent bifunctionality for both the oxygen reduction reaction and the oxygen evolution reaction. Furthermore, op-LN exhibits comparable performances in these reactions to Pt/C and Ir/C, respectively, which highlights its potential for use as a commercially viable bifunctional catalyst. Moreover, the results obtained by testing op-LN in a practical Li-air battery demonstrate improved and complementary charge/discharge performance compared to those of LSCF-NP and NCNT, and this confirms that simply prepared op-LN is a promising candidate as a highly effective bifunctional catalyst for rechargeable metal-air batteries. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Phenotype-genotype discordance in congenital malformations with communication disorders resembling trisomy 18 (Edwards syndrome)

PubMed Central

Pruszewicz, Antoni; Wiskirska-Woźnica, Bożena; Wojnowski, Waldemar; Czerniejewska, Hanna; Jackowska, Joanna; Jarmuż, Małgorzata; Szyfter, Krzysztof; Leszczyńska, Małgorzata

2014-01-01

Patient: Female, 6 Final Diagnosis: Phenotype-genotype discordance in congenital malformations with communication disorders resembling trisomy 18 (Edwards syndrome) Symptoms: — Medication: — Clinical Procedure: — Specialty: Otolaryngology Objective: Congenital defects Background: Communication process disorders are very frequent in rare cases of chromosomal aberrations (deletions, insertions, and trisomies) such as Down syndrome (trisomy 21), Turner syndrome, Edwards syndrome (trisomy 18), or Patau syndrome (trisomy 13). Sometimes phenotype may delusively correspond to the characteristic features of a given syndrome, but genotype tests do not confirm its presence. Case Report: We present the case of a 6-year-old girl admitted to the Clinic of Phoniatrics and Audiology for the assessment of communication in the course of congenital malformations with phenotype characteristic for trisomy 18 (Edwards syndrome). Immediately upon birth, dysmorphic changes suggesting trisomy 18 (Edwards syndrome) were observed, but trisomy 18 was excluded after karyotype test results were normal (46, XX). Conclusions: Disturbed articulation was diagnosed: deformed linguo-dental and palatal sounds, interdental realization with flat tongue of the /s/, /z/, /c/, /dz/, /ś/, /ź/, /ć/, /dz/ sounds (sigmatismus interdentalis). Hearing loss was confirmed. PMID:24478819

49 CFR 655.61 - Action when an employee has a verified positive drug test result or has a confirmed alcohol test...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Action when an employee has a verified positive drug test result or has a confirmed alcohol test result of 0.04 or greater, or refuses to submit to a test. 655.61 Section 655.61 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

49 CFR 655.61 - Action when an employee has a verified positive drug test result or has a confirmed alcohol test...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Action when an employee has a verified positive drug test result or has a confirmed alcohol test result of 0.04 or greater, or refuses to submit to a test. 655.61 Section 655.61 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

49 CFR 655.61 - Action when an employee has a verified positive drug test result or has a confirmed alcohol test...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Action when an employee has a verified positive drug test result or has a confirmed alcohol test result of 0.04 or greater, or refuses to submit to a test. 655.61 Section 655.61 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

49 CFR 655.61 - Action when an employee has a verified positive drug test result or has a confirmed alcohol test...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Action when an employee has a verified positive drug test result or has a confirmed alcohol test result of 0.04 or greater, or refuses to submit to a test. 655.61 Section 655.61 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

49 CFR 655.61 - Action when an employee has a verified positive drug test result or has a confirmed alcohol test...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Action when an employee has a verified positive drug test result or has a confirmed alcohol test result of 0.04 or greater, or refuses to submit to a test. 655.61 Section 655.61 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF...

Application of Titration-Based Screening for the Rapid Pilot Testing of High-Throughput Assays.

PubMed

Zhang, Ji-Hu; Kang, Zhao B; Ardayfio, Ophelia; Ho, Pei-i; Smith, Thomas; Wallace, Iain; Bowes, Scott; Hill, W Adam; Auld, Douglas S

2014-06-01

Pilot testing of an assay intended for high-throughput screening (HTS) with small compound sets is a necessary but often time-consuming step in the validation of an assay protocol. When the initial testing concentration is less than optimal, this can involve iterative testing at different concentrations to further evaluate the pilot outcome, which can be even more time-consuming. Quantitative HTS (qHTS) enables flexible and rapid collection of assay performance statistics, hits at different concentrations, and concentration-response curves in a single experiment. Here we describe the qHTS process for pilot testing in which eight-point concentration-response curves are produced using an interplate asymmetric dilution protocol in which the first four concentrations are used to represent the range of typical HTS screening concentrations and the last four concentrations are added for robust curve fitting to determine potency/efficacy values. We also describe how these data can be analyzed to predict the frequency of false-positives, false-negatives, hit rates, and confirmation rates for the HTS process as a function of screening concentration. By taking into account the compound pharmacology, this pilot-testing paradigm enables rapid assessment of the assay performance and choosing the optimal concentration for the large-scale HTS in one experiment. © 2013 Society for Laboratory Automation and Screening.

Application of YAG Laser TIG Arc Hybrid Welding to Thin AZ31B Magnesium Alloy Sheet

NASA Astrophysics Data System (ADS)

Kim, Taewon; Kim, Jongcheol; Hasegawa, Yu; Suga, Yasuo

A magnesium alloy is said to be an ecological material with high ability of recycling and lightweight property. Especially, magnesium alloys are in great demand on account of outstanding material property as a structural material. Under these circumstances, research and development of welding process to join magnesium alloy plates are of great significance for wide industrial application of magnesium. In order to use it as a structure material, the welding technology is very important. TIG arc welding process is the most ordinary process to weld magnesium alloy plates. However, since the heat source by the arc welding process affects the magnesium alloy plates, HAZ of welded joint becomes wide and large distortion often occurs. On the other hand, a laser welding process that has small diameter of heat source seems to be one of the possible means to weld magnesium alloy in view of the qualitative improvement. However, the low boiling point of magnesium generates some weld defects, including porosity and solidification cracking. Furthermore, precise edge preparation is very important in butt-welding by the laser welding process, due to the small laser beam diameter. Laser/arc hybrid welding process that combines the laser beam and the arc is an effective welding process in which these two heat sources influence and assist each other. Using the hybrid welding, a synegistic effect is achievable and the disadvantages of the respective processes can be compensated. In this study, YAG laser/TIG arc hybrid welding of thin magnesium alloy (AZ31B) sheets was investigated. First of all, the effect of the irradiation point and the focal position of laser beam on the quality of a weld were discussed in hybrid welding. Then, it was confirmed that a sound weld bead with sufficient penetration is obtained using appropriate welding conditions. Furthermore, it was made clear that the heat absorption efficiency is improved with the hybrid welding process. Finally, the tensile tests of welded joints were performed, and it was confirmed that they have sufficient mechanical properties. As a result of this study, it is confirmed that, if the appropriate welding conditions are selected, sound welded joints of AZ31B magnesium alloy are obtainable by the YAG laser/TIG arc hybrid welding process.

Leaching behaviour of hazardous waste under the impact of different ambient conditions.

PubMed

Pecorini, Isabella; Baldi, Francesco; Bacchi, Donata; Carnevale, Ennio Antonio; Corti, Andrea

2017-05-01

The overall objective of this study is to provide an improved basis for the assessment of the leaching behaviour of waste marked as hazardous partly stabilised (European waste catalogue code 19 03 04 ∗ ). Four samples of hazardous partly stabilised waste were subjected to two leaching tests: up-flow column tests and batch equilibrium tests. The research was carried out in two directions: the first aims at comparing the results of the two experimental setups while the second aims at assessing the impact of different ambient conditions on the leaching behaviour of waste. Concerning this latter objective the effect of mesophilic temperature, mechanical constraints and acid environment were tested through column percolation tests. Results showed no significant differences between batch and column leaching test outcomes when comparing average concentrations calculated at a liquid to solid ratio of 10:1 l kg -1  TS. Among the tested ambient conditions, the presence of an acid environment (pH=4.5) accelerated the leaching process resulting in a higher cumulative released quantity measured on the majority of the investigated polluting substances. On the contrary, the effect of temperature and mechanical constraints seemed to not affect the process showing final contents even lower than values found for the standard test. This result was furthermore confirmed by the application of the principal component analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of a pericardial acellular matrix biomaterial: biochemical and mechanical effects of cell extraction.

PubMed

Courtman, D W; Pereira, C A; Kashef, V; McComb, D; Lee, J M; Wilson, G J

1994-06-01

There is evidence to suggest that the cellular components of homografts and bioprosthetic xenografts may contribute to calcification or immunogenic reactions. A four-step detergent and enzymatic extraction process has been developed to remove cellular components from bovine pericardial tissue. The process results in an acellular matrix material consisting primarily of elastin, insoluble collagen, and tightly bound glycosaminoglycans. Light and electron microscopy confirmed that nearly all cellular constituents are removed without ultrastructural evidence of damage to fibrous components. Collagen denaturation temperatures remained unaltered. Biochemical analysis confirmed the retention of collagen and elastin and some differential extraction of glycosaminoglycans. Low strain rate fracture testing and high strain rate viscoelastic characterization showed that, with the exception of slightly increased stress relaxation, the mechanical properties of the fresh tissue were preserved in the pericardial acellular matrix. Crosslinking of the material in glutaraldehyde or poly(glycidyl ether) produced mechanical changes consistent with the same treatments of fresh tissue. The pericardial acellular matrix is a promising approach to the production of biomaterials for heart valve or cardiovascular patching applications.

[Extraction method suitable for detection of unheated crustaceans including cephalothorax by ELISA].

PubMed

Shibahara, Yusuke; Yamada, Itta; Uesaka, Yoshihiko; Uneo, Noriko; Abe, Akihisa; Ohashi, Eiji; Shiomi, Kazuo

2009-08-01

When unheated whole samples of crustaceans (shrimp, prawn and crab) were analyzed with our ELISA kit (FA test EIA-Crustacean 'Nissui') using anti-tropomyosin antibodies, a remarkable reduction in reactivity was recognized. This reduction in activity was found to be due to the digestion of tropomyosin during the extraction process by proteases contained in cephalothorax. To avoid the digestion of tropomyosin by proteases, we developed an extraction method (heating method) suitable for the detection of tropomyosin in unheated crustaceans including cephalothorax. Experiments with unheated whole samples of various species of crustaceans confirmed that the heating method greatly improved the low reactivity in the standard method; the heating method gave extraction efficiencies of as high as 93-107%. Various processed crustaceans with cephalothorax, such as dry products (unheated or weakly heated products) and pickles in soy sauce (unheated products), that showed low reactivity with the standard method were confirmed to give superior results with the heating method. These results indicated that the developed heating method is suitable for detecting unheated crustaceans with cephalothorax by means of the ELISA kit.

Mantle Cell Hyperplasia of Peripheral Lymph Nodes as Initial Manifestation of Sickle Cell Disease.

PubMed

Monabbati, Ahmad; Noori, Sadat; Safaei, Akbar; Ramzi, Mani; Eghbali, Seyedsajjad; Adib, Ali

2016-01-01

Sickle cell disease (SCD) is a well known hemoglobinopathy with usual manifestations including anemia, hyperbilirubinemia, and vasoocclusive complications. Despite presence of mild splenomegaly in early phase of the disease, lymphadenopathy is not an often finding of SCD. We introduce an undiagnosed case of SCD who presented in third decade of his life with multiple cervical lymphadenopathies and mild splenomegaly persistent for about five years. Histopathologic examination of the resected lymph nodes showed expansion of the mantle cell layers of secondary follicles as well as several monomorphic mantle cell nodules. To rule out possibility of a malignant process involving lymph nodes, an immunohistochemical panel was ordered which was in favor of benign mantle cell hyperplasia. Immunoglobulin gene rearrangement study showed no clonal bands and confirmed benign nature of the process. Respecting mild abnormalities on Complete Blood Count, peripheral blood smear was reviewed revealing some typical sickle red blood cells as well as rare nucleated red blood cells. Solubility test for hemoglobin (HB) S was positive. Hemoglobin electrophoresis confirmed diagnosis of homozygous HbS disease.

DESTRUCTION OF TETRAPHENYLBORATE IN TANK 48H USING WET AIR OXIDATION BATCH BENCH SCALE AUTOCLAVE TESTING WITH ACTUAL RADIOACTIVE TANK 48H WASTE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adu-Wusu, K; Paul Burket, P

2009-03-31

Wet Air Oxidation (WAO) is one of the two technologies being considered for the destruction of Tetraphenylborate (TPB) in Tank 48H. Batch bench-scale autoclave testing with radioactive (actual) Tank 48H waste is among the tests required in the WAO Technology Maturation Plan. The goal of the autoclave testing is to validate that the simulant being used for extensive WAO vendor testing adequately represents the Tank 48H waste. The test objective was to demonstrate comparable test results when running simulated waste and real waste under similar test conditions. Specifically: (1) Confirm the TPB destruction efficiency and rate (same reaction times) obtainedmore » from comparable simulant tests, (2) Determine the destruction efficiency of other organics including biphenyl, (3) Identify and quantify the reaction byproducts, and (4) Determine off-gas composition. Batch bench-scale stirred autoclave tests were conducted with simulated and actual Tank 48H wastes at SRNL. Experimental conditions were chosen based on continuous-flow pilot-scale simulant testing performed at Siemens Water Technologies Corporation (SWT) in Rothschild, Wisconsin. The following items were demonstrated as a result of this testing. (1) Tetraphenylborate was destroyed to below detection limits during the 1-hour reaction time at 280 C. Destruction efficiency of TPB was > 99.997%. (2) Other organics (TPB associated compounds), except biphenyl, were destroyed to below their respective detection limits. Biphenyl was partially destroyed in the process, mainly due to its propensity to reside in the vapor phase during the WAO reaction. Biphenyl is expected to be removed in the gas phase during the actual process, which is a continuous-flow system. (3) Reaction byproducts, remnants of MST, and the PUREX sludge, were characterized in this work. Radioactive species, such as Pu, Sr-90 and Cs-137 were quantified in the filtrate and slurry samples. Notably, Cs-137, boron and potassium were shown as soluble as a result of the WAO reaction. (4) Off-gas composition was measured in the resulting gas phase from the reaction. Benzene and hydrogen were formed during the reaction, but they were reasonably low in the off-gas at 0.096 and 0.0063 vol% respectively. Considering the consistency in replicating similar test results with simulated waste and Tank 48H waste under similar test conditions, the results confirm the validity of the simulant for other WAO test conditions.« less

Memory in pregnancy and post-partum: Item specific and relational encoding processes in recall and recognition.

PubMed

Spataro, Pietro; Saraulli, Daniele; Oriolo, Debora; Costanzi, Marco; Zanetti, Humberto; Cestari, Vincenzo; Rossi-Arnaud, Clelia

2016-08-01

It has been recently proposed that pregnant women would perform memory tasks by focusing more on item-specific processes and less on relational processing, compared to post-partum women (Mickes, Wixted, Shapiro & Scarff, ). The present cross-sectional study tested this hypothesis by directly manipulating the type of encoding employed in the study phase. Pregnant, post-partum and control women either rated the pleasantness of word meaning (which induced item-specific elaboration) or named the semantic category to which they belonged (which induced relational elaboration). Memory for the encoded words was later tested in free recall (which emphasizes relational processing) and in recognition (which emphasizes item-specific processing). In line with Mickes et al.'s () conclusions, pregnant women in the item-specific condition performed worse than post-partum women in the relational condition in free recall, but not in recognition. However, compared to the other two groups, pregnant women also exhibited lower recognition accuracy in the item-specific condition. Overall, these results confirm that pregnant women rely on relational encoding less than post-partum women, but additionally suggest that the former group might use item-specific processes less efficiently than post-partum and control women. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

Risks of beryllium disease related to work processes at a metal, alloy, and oxide production plant.

PubMed

Kreiss, K; Mroz, M M; Zhen, B; Wiedemann, H; Barna, B

1997-08-01

To describe relative hazards in sectors of the beryllium industry, risk factors of beryllium disease and sensitisation related to work process were sought in a beryllium manufacturing plant producing pure metal, oxide, alloys, and ceramics. All 646 active employees were interviewed; beryllium sensitisation was ascertained with the beryllium lymphocyte proliferation blood test on 627 employees; clinical evaluation and bronchoscopy were offered to people with abnormal test results; and industrial hygiene measurements related to work processes taken in 1984-93 were reviewed. 59 employees (9.4%) had abnormal blood tests, 47 of whom underwent bronchoscopy. 24 new cases of beryllium disease were identified, resulting in a beryllium disease prevalence of 4.6%, including five known cases (29/632). Employees who had worked in ceramics had the highest prevalence of beryllium disease (9.0%). Employees in the pebble plant (producing beryllium metal) who had been employed after 1983 also had increased risk, with a prevalence of beryllium disease of 6.4%, compared with 1.3% of other workers hired in the same period, and a prevalence of abnormal blood tests of 19.2%. Logistic regression modelling confirmed these two risk factors for beryllium disease related to work processes and the dependence on time of the risk at the pebble plant. The pebble plant was not associated with the highest gravimetric industrial hygiene measurements available since 1984. Further characterisation of exposures in beryllium metal production may be important to understanding how beryllium exposures confer high contemporary risk of beryllium disease.

Paint removal using wheat starch blast media

NASA Astrophysics Data System (ADS)

Foster, Terry; Oestreich, John

1993-03-01

A review of the Wheat Starch Blasting technology is presented. Laboratory evaluations covering Almen Arc testing on bare 2024-T3 aluminum and magnesium, as well as crack detection on 7075-T6 bare aluminum, are discussed. Comparisons with Type V plastic media show lower residual stresses are achieved on aluminum and magnesium with wheat starch media. Dry blasting effects on the detection of cracks confirms better crack visibility with wheat starch media versus Type V or Type II plastic media. Testing of wheat starch media in several composite test programs, including fiberglass, Kevlar, and graphite-epoxy composites, showed no fiber damage. Process developments and production experience at the first U.S. aircraft stripping facility are also reviewed. Corporate and regional aircraft are being stripped in this three nozzle dry blast hanger.

Development of the performance confirmation program at YUCCA mountain, nevada

USGS Publications Warehouse

LeCain, G.D.; Barr, D.; Weaver, D.; Snell, R.; Goodin, S.W.; Hansen, F.D.

2006-01-01

The Yucca Mountain Performance Confirmation program consists of tests, monitoring activities, experiments, and analyses to evaluate the adequacy of assumptions, data, and analyses that form the basis of the conceptual and numerical models of flow and transport associated with a proposed radioactive waste repository at Yucca Mountain, Nevada. The Performance Confirmation program uses an eight-stage risk-informed, performance-based approach. Selection of the Performance Confirmation activities for inclusion in the Performance Confirmation program was done using a risk-informed performance-based decision analysis. The result of this analysis was a Performance Confirmation base portfolio that consists of 20 activities. The 20 Performance Confirmation activities include geologic, hydrologie, and construction/engineering testing. Some of the activities began during site characterization, and others will begin during construction, or post emplacement, and continue until repository closure.

Syphilis screening in the Blood Transfusion Service: a report of four years' experience with the Treponema pallidum haemagglutination assay and the subsequent development of a rapid "spin" method.

PubMed Central

Puckett, A; Pratt, G

1987-01-01

A comparison of cardiolipin and a modified Treponema pallidum haemagglutination assay (TPHA) method over a four year period confirmed the superior sensitivity and specificity of TPHA. In 86,495 new donor sera 19 (0.02%) confirmed positive results were detected by TPHA, 10 of which did not react by the cardiolipin test. In 150,789 antenatal samples 49 confirmed positive results were found by TPHA, 30 of which did not react by cardiolipin. No cardiolipin positive, TPHA negative samples were confirmed as positive by the absorbed fluorescence treponemal antibody test, and overall 78% of cardiolipin reactions gave false biological positive results. Cardiolipin tests were continued only because of their speed. A further modification ("spin") of the TPHA has now been developed which is rapid, sensitive, and inexpensive, and in testing 21,807 sera, gave results equivalent to those of the previous "settle" method. Serious consideration should be given to dispensing with cardiolipin tests. PMID:3320095

Validating the Construct of Coercion in Family Routines: Expanding the Unit of Analysis in Behavioral Assessment with Families of Children with Developmental Disabilities

PubMed Central

Lucyshyn, Joseph M.; Irvin, Larry K.; Blumberg, E. Richard; Laverty, Robelyn; Horner, Robert H.; Sprague, Jeffrey R.

2015-01-01

We conducted an observational study of parent-child interaction in home activity settings (routines) of families raising young children with developmental disabilities and problem behavior. Our aim was to empirically investigate the construct validity of coercion in typical but unsuccessful family routines. The long-term goal was to develop an expanded ecological unit of analysis that may contribute to sustainable behavioral family intervention. Ten children with autism and/or mental retardation and their families participated. Videotaped observations were conducted in typical but unsuccessful home routines. Parent-child interaction in routines was coded in real time and sequential analyses were conducted to test hypotheses about coercive processes. Following observation, families were interviewed about the social validity of the construct. Results confirmed the presence of statistically significant, attention-driven coercive processes in routines in which parents were occupied with non-child centered tasks. Results partially confirmed the presence of escape-driven coercive processes in routines in which parent demands are common. Additional analysis revealed an alternative pattern with greater magnitude. Family perspectives suggested the social validity of the construct. Results are discussed in terms of preliminary, partial evidence for coercive processes in routines of families of children with developmental disabilities. Implications for behavioral assessment and intervention design are discussed. PMID:26321883

Y-TZP ceramic processing from coprecipitated powders: a comparative study with three commercial dental ceramics.

PubMed

Lazar, Dolores R R; Bottino, Marco C; Ozcan, Mutlu; Valandro, Luiz Felipe; Amaral, Regina; Ussui, Valter; Bressiani, Ana H A

2008-12-01

(1) To synthesize 3mol% yttria-stabilized zirconia (3Y-TZP) powders via coprecipitation route, (2) to obtain zirconia ceramic specimens, analyze surface characteristics, and mechanical properties, and (3) to compare the processed material with three reinforced dental ceramics. A coprecipitation route was used to synthesize a 3mol% yttria-stabilized zirconia ceramic processed by uniaxial compaction and pressureless sintering. Commercially available alumina or alumina/zirconia ceramics, namely Procera AllCeram (PA), In-Ceram Zirconia Block (CAZ) and In-Ceram Zirconia (IZ) were chosen for comparison. All specimens (6mmx5mmx5mm) were polished and ultrasonically cleaned. Qualitative phase analysis was performed by XRD and apparent densities were measured on the basis of Archimedes principle. Ceramics were also characterized using SEM, TEM and EDS. The hardness measurements were made employing Vickers hardness test. Fracture toughness (K(IC)) was calculated. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey's test (alpha=0.05). ANOVA revealed that the Vickers hardness (p<0.0001) and fracture toughness (p<0.0001) were affected by the ceramic materials composition. It was confirmed that the PA ceramic was constituted of a rhombohedral alumina matrix, so-called alpha-alumina. Both CAZ and IZ ceramics presented tetragonal zirconia and alpha-alumina mixture of phases. The SEM/EDS analysis confirmed the presence of aluminum in PA ceramic. In the IZ and CAZ ceramics aluminum, zirconium and cerium in grains involved by a second phase containing aluminum, silicon and lanthanum were identified. PA showed significantly higher mean Vickers hardness values (H(V)) (18.4+/-0.5GPa) compared to vitreous CAZ (10.3+/-0.2GPa) and IZ (10.6+/-0.4GPa) ceramics. Experimental Y-TZP showed significantly lower results than that of the other monophased ceramic (PA) (p<0.05) but it showed significantly higher fracture toughness (6.0+/-0.2MPam(1/2)) values when compared to the other tested ceramics (p<0.05). The coprecipitation method used to synthesize zirconia powders and the adopted ceramic processing conditions led to ceramics with mechanical properties comparable to commercially available reinforced ceramic materials.

Testing the predictive power of the transtheoretical model of behavior change applied to dietary fat intake

PubMed Central

Wright, Julie A.; Velicer, Wayne F.; Prochaska, James O.

2009-01-01

This study evaluated how well predictions from the transtheoretical model (TTM) generalized from smoking to diet. Longitudinal data were used from a randomized control trial on reducing dietary fat consumption in adults (n =1207) recruited from primary care practices. Predictive power was evaluated by making a priori predictions of the magnitude of change expected in the TTM constructs of temptation, pros and cons, and 10 processes of change when an individual transitions between the stages of change. Generalizability was evaluated by testing predictions based on smoking data. Three sets of predictions were made for each stage: Precontemplation (PC), Contemplation (C) and Preparation (PR) based on stage transition categories of no progress, progress and regression determined by stage at baseline versus stage at the 12-month follow-up. Univariate analysis of variance between stage transition groups was used to calculate the effect size [omega squared (ω2)]. For diet predictions based on diet data, there was a high degree of confirmation: 92%, 95% and 92% for PC, C and PR, respectively. For diet predictions based on smoking data, 77%, 79% and 85% were confirmed, respectively, suggesting a moderate degree of generalizability. This study revised effect size estimates for future theory testing on the TTM applied to dietary fat. PMID:18400785

Biological characterization of a novel in vitro cell irradiator

PubMed Central

Fowler, Tyler L.; Fisher, Michael M.; Bailey, Alison M.; Bednarz, Bryan P.

2017-01-01

To evaluate the overall robustness of a novel cellular irradiator we performed a series of well-characterized, dose-responsive assays to assess the consequences of DNA damage. We used a previously described novel irradiation system and a traditional 137Cs source to irradiate a cell line. The generation of reactive oxygen species was assessed using chloromethyl-H2DCFDA dye, the induction of DNA DSBs was observed using the comet assay, and the initiation of DNA break repair was assessed through γH2AX image cytometry. A high correlation between physical absorbed dose and biologic dose was seen for the production of intracellular reactive oxygen species, physical DNA double strand breaks, and modulation of the cellular double stand break pathway. The results compared favorably to irradiation with a traditional 137Cs source. The rapid, straightforward tests described form a reasonable approach for biologic characterization of novel irradiators. These additional testing metrics go beyond standard physics testing such as Monte Carlo simulation and thermo-luminescent dosimeter evaluation to confirm that a novel irradiator can produce the desired dose effects in vitro. Further, assessment of these biological metrics confirms that the physical handling of the cells during the irradiation process results in biologic effects that scale appropriately with dose. PMID:29232400

[The Scope, Quality and Safety Requirements of Drug Abuse Testing].

PubMed

Küme, Tuncay; Karakükcü, Çiğdem; Pınar, Aslı; Coşkunol, Hakan

2017-01-01

The aim of this review is to inform about the scopes and requirements of drug abuse testing. Drug abuse testing is one of the tools for determination of drug use. It must fulfill the quality and safety requirements in judgmental legal and administrative decisions. Drug abuse testing must fulfill some requirements like selection of the appropriate test matrix, appropriate screening test panel, sampling in detection window, patient consent, identification of the donor, appropriate collection site, sample collection with observation, identification and control of the sample, specimen custody chain in preanalytical phase; analysis in authorized laboratories, specimen validity tests, reliable testing METHODS, strict quality control, two-step analysis in analytical phase; storage of the split specimen, confirmation of the split specimen in the objection, result custody chain, appropriate cut-off concentration, the appropriate interpretation of the result in postanalytical phase. The workflow and analytical processes of drug abuse testing are explained in last regulation of the Department of Medical Laboratory Services, Ministry of Health in Turkey. The clinical physicians have to know and apply the quality and safety requirements in drug abuse testing according to last regulations in Turkey.

3-D loaded scaffolds obtained by supercritical CO2 assisted process

NASA Astrophysics Data System (ADS)

Cardea, S.; Reverchon, E.

2014-08-01

In this work, a supercritical CO2 (SC-CO2) drying process for the formation of 3-D PVDF-HFP loaded scaffolds was tested. Experiments at pressures ranging between 150 and 250 bar and at temperatures ranging between 35 and 55°C were performed. The PVDF-HFP- acetone-ethanol solution at 15% w/w polymer was selected as the base case. The drug (amoxicillin) concentration was varied from 20 to 30% w/w with respect to PVDF-HFP. SC- CO2 drying process was confirmed to be a valid alternative to generate loaded structures; indeed, scaffolds characterized by nanometric networks (with mean pore diameter of about 300 nm) with a homogeneous drug distribution were obtained. Drug controlled release experiments were also performed and a quasi-zero order release kinetic was observed.

AMO Teledioptric System for age-related macular degeneration

NASA Astrophysics Data System (ADS)

Chou, Jim-Son; Ting, Albert C.

1994-05-01

A 2.5 X magnification system consisting of a two-zone intraocular implant and a spectacle was developed, tested, and clinically tried by fifty patients with cataract ad age-related macular degeneration. Optical bench testing results and clinical data confirmed that the field of view of the system was 2.6 times wider than an equivalent external telescope. The study also demonstrated that the implant itself was clinically equivalent to a standard monofocal intraocular lens for cataract. The clinical study indicated that higher magnification without compromising the compactness and optical quality was needed as the disease progressed. Also, a sound vision rehabilitation process is important to provide patients the full benefits of the system.

Research on HOPE communication and data processing equipment

NASA Astrophysics Data System (ADS)

Yamamoto, Satoru; Kikuchi, Toshio

1992-08-01

An overview of the research on heat-resisting antenna is presented. Candidate heat-resisting antennas which were selected as the result of review on seven kinds of antenna are the antennas of micro strip, cavity, and horn types. Heat resistance characteristics of electric power supplying section (connectors) of heat-resisting antenna were studied. Heat cycling test and heat shock tests were conducted on the subject plugs and it was confirmed that they can be usable at - 80 C to + 200 C against - 65 C to + 125 C for the existing plugs. Fundamental electric data such as antenna pattern were acquired mating trial produced components simulating electric characteristics of heat-resisting antenna and trial-produced ceramic tiles.

Generalized sensitivity analysis of the minimal model of the intravenous glucose tolerance test.

PubMed

Munir, Mohammad

2018-06-01

Generalized sensitivity functions characterize the sensitivity of the parameter estimates with respect to the nominal parameters. We observe from the generalized sensitivity analysis of the minimal model of the intravenous glucose tolerance test that the measurements of insulin, 62 min after the administration of the glucose bolus into the experimental subject's body, possess no information about the parameter estimates. The glucose measurements possess the information about the parameter estimates up to three hours. These observations have been verified by the parameter estimation of the minimal model. The standard errors of the estimates and crude Monte Carlo process also confirm this observation. Copyright © 2018 Elsevier Inc. All rights reserved.

Maturity-onset diabetes of the young (MODY): how many cases are we missing?

PubMed

Shields, B M; Hicks, S; Shepherd, M H; Colclough, K; Hattersley, A T; Ellard, S

2010-12-01

Maturity-onset diabetes of the young is frequently misdiagnosed as type 1 or type 2 diabetes. A correct diagnosis of MODY is important for determining treatment, but can only be confirmed by molecular genetic testing. We aimed to compare the regional distribution of confirmed MODY cases in the UK and to estimate the minimum prevalence. UK referrals for genetic testing in 2,072 probands and 1,280 relatives between 1996 and 2009 were examined by region, country and test result. Referral rate and prevalence were calculated using UK Census 2001 figures. MODY was confirmed in 1,177 (35%) patients, with HNF1A (52%) and GCK mutations (32%) being most frequent in probands confirmed with MODY. There was considerable regional variation in proband referral rates (from <20 per million in Wales and Northern Ireland to >50 per million for South West England and Scotland) and patients diagnosed with MODY (5.3 per million in Northern Ireland, 48.9 per million in South West England). Referral rates and confirmed cases were highly correlated (r = 0.96, p < 0.0001). The minimum prevalence of MODY was estimated to be 108 cases per million. Assuming this minimal prevalence throughout the UK then >80% of MODY is not diagnosed by molecular testing. The marked regional variation in the prevalence of confirmed MODY directly results from differences in referral rates. This could reflect variation in awareness of MODY or unequal access to genetic testing. Increased referral for diagnostic testing is required if the majority of MODY patients are to have the genetic diagnosis necessary for optimal treatment.

Magnetically aligned nanodomains: application in high-performance ion conductive membranes.

PubMed

Hasani-Sadrabadi, Mohammad Mahdi; Majedi, Fatemeh Sadat; Coullerez, Géraldine; Dashtimoghadam, Erfan; VanDersarl, Jules John; Bertsch, Arnaud; Moaddel, Homayoun; Jacob, Karl I; Renaud, Philippe

2014-05-28

Polyelectrolyte-coated magnetic nanoparticles were prepared by decorating the surface of superparamagnetic iron oxide nanoparticles (SPIONs) with crosslinked chitosan oligopolysaccharide (CS). These positively charged particles (CS-SPIONs) were then added to a negatively charged polymer (Nafion), and cast into membranes under an applied magnetic field. TEM and SAXS measurements confirmed this process created aligned, cylindrical nanodomains in the membranes. This was also indirectly confirmed by proton conductivity values. The strong electrostatic interaction between chitosan and Nafion prevented oxygen permeability and water evaporation at elevated temperatures through the proton conductive channels. The resultant proton exchange membranes showed lower conduction dependency to relative humidity, which is highly desirable for hydrogen fuel cells. The fuel cell performance tests were performed on the designed polyelectrolyte membrane by hydrogen-oxygen single cells at elevated temperature (120 °C) and low relative humidity.

Addressing case specific biogas plant tasks: industry oriented methane yields derived from 5L Automatic Methane Potential Test Systems in batch or semi-continuous tests using realistic inocula, substrate particle sizes and organic loading.

PubMed

Kolbl, Sabina; Paloczi, Attila; Panjan, Jože; Stres, Blaž

2014-02-01

The primary aim of the study was to develop and validate an in-house upscale of Automatic Methane Potential Test System II for studying real-time inocula and real-scale substrates in batch, codigestion and enzyme enhanced hydrolysis experiments, in addition to semi-continuous operation of the developed equipment and experiments testing inoculum functional quality. The successful upscale to 5L enabled comparison of different process configurations in shorter preparation times with acceptable accuracy and high-through put intended for industrial decision making. The adoption of the same scales, equipment and methodologies in batch and semi-continuous tests mirroring those at full scale biogas plants resulted in matching methane yields between the two laboratory tests and full-scale, confirming thus the increased decision making value of the approach for industrial operations. Copyright © 2013 Elsevier Ltd. All rights reserved.

The 3 faces of clinical reasoning: Epistemological explorations of disparate error reduction strategies.

PubMed

Monteiro, Sandra; Norman, Geoff; Sherbino, Jonathan

2018-06-01

There is general consensus that clinical reasoning involves 2 stages: a rapid stage where 1 or more diagnostic hypotheses are advanced and a slower stage where these hypotheses are tested or confirmed. The rapid hypothesis generation stage is considered inaccessible for analysis or observation. Consequently, recent research on clinical reasoning has focused specifically on improving the accuracy of the slower, hypothesis confirmation stage. Three perspectives have developed in this line of research, and each proposes different error reduction strategies for clinical reasoning. This paper considers these 3 perspectives and examines the underlying assumptions. Additionally, this paper reviews the evidence, or lack of, behind each class of error reduction strategies. The first perspective takes an epidemiological stance, appealing to the benefits of incorporating population data and evidence-based medicine in every day clinical reasoning. The second builds on the heuristic and bias research programme, appealing to a special class of dual process reasoning models that theorizes a rapid error prone cognitive process for problem solving with a slower more logical cognitive process capable of correcting those errors. Finally, the third perspective borrows from an exemplar model of categorization that explicitly relates clinical knowledge and experience to diagnostic accuracy. © 2018 John Wiley & Sons, Ltd.

Candida antarctica Lipase B Immobilized onto Chitin Conjugated with POSS® Compounds: Useful Tool for Rapeseed Oil Conversion

PubMed Central

Zdarta, Jakub; Wysokowski, Marcin; Norman, Małgorzata; Kołodziejczak-Radzimska, Agnieszka; Moszyński, Dariusz; Maciejewski, Hieronim; Ehrlich, Hermann; Jesionowski, Teofil

2016-01-01

A new method is proposed for the production of a novel chitin-polyhedral oligomeric silsesquioxanes (POSS) enzyme support. Analysis by such techniques as X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy confirmed the effective functionalization of the chitin surface. The resulting hybrid carriers were used in the process of immobilization of the lipase type b from Candida antarctica (CALB). Fourier transform infrared spectroscopy (FTIR) confirmed the effective immobilization of the enzyme. The tests of the catalytic activity showed that the resulting support-biocatalyst systems remain hydrolytically active (retention of the hydrolytic activity up to 87% for the chitin + Methacryl POSS® cage mixture (MPOSS) + CALB after 24 h of the immobilization), as well as represents good thermal and operational stability, and retain over 80% of its activity in a wide range of temperatures (30–60 °C) and pH (6–9). Chitin-POSS-lipase systems were used in the transesterification processes of rapeseed oil at various reaction conditions. Produced systems allowed the total conversion of the oil to fatty acid methyl esters (FAME) and glycerol after 24 h of the process at pH 10 and a temperature 40 °C, while the Methacryl POSS® cage mixture (MPOSS) was used as a chitin-modifying agent. PMID:27657054

Corrosion Resistance of Laser Clads of Inconel 625 and Metco 41C

NASA Astrophysics Data System (ADS)

Němeček, Stanislav; Fidler, Lukáš; Fišerová, Pavla

The present paper explores the impact of laser cladding parameters on the corrosion behaviour of the resulting surface. Powders of Inconel 625 and austenitic Metco 41C steel were deposited on steel substrate. It was confirmed that the level of dilution has profound impact on the corrosion resistance and that dilution has to be minimized. However, the chemical composition of the cladding is altered even in the course of the cladding process, a fact which is related to the increase in the substrate temperature. The cladding process was optimized to achieve maximum corrosion resistance. The results were verified and validated using microscopic observation, chemical analysis and corrosion testing.

Biofilms associated with poultry processing equipment.

PubMed

Lindsay, D; Geornaras, I; von Holy, A

1996-01-01

Aerobic and Gram-negative bacteria were enumerated on non-metallic surfaces and stainless steel test pieces attached to equipment surfaces by swabbing and a mechanical dislodging procedure, respectively, in a South African grade B poultry processing plant. Changes in bacterial numbers were also monitored over time on metal test pieces. The highest bacterial counts were obtained from non-metallic surfaces such as rubber fingered pluckers and plastic defeathering curtains which exceeded the highest counts found on the metal surfaces by at least 1 log CFU cm-2. Gram-negative bacterial counts on all non-metallic surface types were at least 2 log CFU cm-2 lower than corresponding aerobic plate counts. On metal surfaces, the highest microbial numbers were obtained after 14 days exposure, with aerobic plate counts ranging from 3.57 log CFU cm-2 to 5.13 log CFU cm-2, and Gram-negative counts from 0.70 log CFU cm-2 to 3.31 log CFU cm-2. Scanning electron microscopy confirmed the presence of bacterial cells on non-metallic and metallic surfaces associated with poultry processing. Rubber 'fingers', plastic curtains, conveyor belt material and stainless steel test surfaces placed on the scald tank overflow and several chutes revealed extensive and often confluent bacterial biofilms. Extracellular polymeric substances, but few bacterial cells were visible on test pieces placed on evisceration equipment, spinchiller blades and the spinchiller outlet.

Testing of an advanced thermochemical conversion reactor system

NASA Astrophysics Data System (ADS)

1990-01-01

This report presents the results of work conducted by MTCI to verify and confirm experimentally the ability of the MTCI gasification process to effectively generate a high-quality, medium-Btu gas from a wider variety of feedstock and waste than that attainable in air-blown, direct gasification systems. The system's overall simplicity, due to the compact nature of the pulse combustor, and the high heat transfer rates attainable within the pulsating flow resonance tubes, provide a decided and near-term potential economic advantage for the MTCI indirect gasification system. The primary objective was the design, construction, and testing of a Process Design Verification System for an indirectly heated, thermochemical fluid-bed reactor and a pulse combustor an an integrated system that can process alternative renewable sources of energy such as biomass, black liquor, municipal solid waste and waste hydrocarbons, including heavy oils into a useful product gas. The test objectives for the biomass portion of this program were to establish definitive performance data on biomass feedstocks covering a wide range of feedstock qualities and characteristics. The test objectives for the black liquor portion of this program were to verify the operation of the indirect gasifier on commercial black liquor containing 65 percent solids at several temperature levels and to characterize the bed carbon content, bed solids particle size and sulfur distribution as a function of gasification conditions.

Field Calibration of Wind Direction Sensor to the True North and Its Application to the Daegwanryung Wind Turbine Test Sites

PubMed Central

Lee, Jeong Wan

2008-01-01

This paper proposes a field calibration technique for aligning a wind direction sensor to the true north. The proposed technique uses the synchronized measurements of captured images by a camera, and the output voltage of a wind direction sensor. The true wind direction was evaluated through image processing techniques using the captured picture of the sensor with the least square sense. Then, the evaluated true value was compared with the measured output voltage of the sensor. This technique solves the discordance problem of the wind direction sensor in the process of installing meteorological mast. For this proposed technique, some uncertainty analyses are presented and the calibration accuracy is discussed. Finally, the proposed technique was applied to the real meteorological mast at the Daegwanryung test site, and the statistical analysis of the experimental testing estimated the values of stable misalignment and uncertainty level. In a strict sense, it is confirmed that the error range of the misalignment from the exact north could be expected to decrease within the credibility level. PMID:27873957

Fiber-optically sensorized composite wing

NASA Astrophysics Data System (ADS)

Costa, Joannes M.; Black, Richard J.; Moslehi, Behzad; Oblea, Levy; Patel, Rona; Sotoudeh, Vahid; Abouzeida, Essam; Quinones, Vladimir; Gowayed, Yasser; Soobramaney, Paul; Flowers, George

2014-04-01

Electromagnetic interference (EMI) immune and light-weight, fiber-optic sensor based Structural Health Monitoring (SHM) will find increasing application in aerospace structures ranging from aircraft wings to jet engine vanes. Intelligent Fiber Optic Systems Corporation (IFOS) has been developing multi-functional fiber Bragg grating (FBG) sensor systems including parallel processing FBG interrogators combined with advanced signal processing for SHM, structural state sensing and load monitoring applications. This paper reports work with Auburn University on embedding and testing FBG sensor arrays in a quarter scale model of a T38 composite wing. The wing was designed and manufactured using fabric reinforced polymer matrix composites. FBG sensors were embedded under the top layer of the composite. Their positions were chosen based on strain maps determined by finite element analysis. Static and dynamic testing confirmed expected response from the FBGs. The demonstrated technology has the potential to be further developed into an autonomous onboard system to perform load monitoring, SHM and Non-Destructive Evaluation (NDE) of composite aerospace structures (wings and rotorcraft blades). This platform technology could also be applied to flight testing of morphing and aero-elastic control surfaces.

Estimating psycho-physiological state of a human by speech analysis

NASA Astrophysics Data System (ADS)

Ronzhin, A. L.

2005-05-01

Adverse effects of intoxication, fatigue and boredom could degrade performance of highly trained operators of complex technical systems with potentially catastrophic consequences. Existing physiological fitness for duty tests are time consuming, costly, invasive, and highly unpopular. Known non-physiological tests constitute a secondary task and interfere with the busy workload of the tested operator. Various attempts to assess the current status of the operator by processing of "normal operational data" often lead to excessive amount of computations, poorly justified metrics, and ambiguity of results. At the same time, speech analysis presents a natural, non-invasive approach based upon well-established efficient data processing. In addition, it supports both behavioral and physiological biometric. This paper presents an approach facilitating robust speech analysis/understanding process in spite of natural speech variability and background noise. Automatic speech recognition is suggested as a technique for the detection of changes in the psycho-physiological state of a human that typically manifest themselves by changes of characteristics of voice tract and semantic-syntactic connectivity of conversation. Preliminary tests have confirmed that the statistically significant correlation between the error rate of automatic speech recognition and the extent of alcohol intoxication does exist. In addition, the obtained data allowed exploring some interesting correlations and establishing some quantitative models. It is proposed to utilize this approach as a part of fitness for duty test and compare its efficiency with analyses of iris, face geometry, thermography and other popular non-invasive biometric techniques.

Soft sensor for real-time cement fineness estimation.

PubMed

Stanišić, Darko; Jorgovanović, Nikola; Popov, Nikola; Čongradac, Velimir

2015-03-01

This paper describes the design and implementation of soft sensors to estimate cement fineness. Soft sensors are mathematical models that use available data to provide real-time information on process variables when the information, for whatever reason, is not available by direct measurement. In this application, soft sensors are used to provide information on process variable normally provided by off-line laboratory tests performed at large time intervals. Cement fineness is one of the crucial parameters that define the quality of produced cement. Providing real-time information on cement fineness using soft sensors can overcome limitations and problems that originate from a lack of information between two laboratory tests. The model inputs were selected from candidate process variables using an information theoretic approach. Models based on multi-layer perceptrons were developed, and their ability to estimate cement fineness of laboratory samples was analyzed. Models that had the best performance, and capacity to adopt changes in the cement grinding circuit were selected to implement soft sensors. Soft sensors were tested using data from a continuous cement production to demonstrate their use in real-time fineness estimation. Their performance was highly satisfactory, and the sensors proved to be capable of providing valuable information on cement grinding circuit performance. After successful off-line tests, soft sensors were implemented and installed in the control room of a cement factory. Results on the site confirm results obtained by tests conducted during soft sensor development. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Tracing the contamination origin of coliform bacteria in two small food-processing factories.

PubMed

Tominaga, Tatsuya; Sekine, Masahiro; Oyaizu, Hiroshi

2008-09-01

The objective of this study was to trace contamination sources of coliform bacteria by comparing the types of coliforms between food samples and the processing environments in two small food-processing factories (factories A and B). Fermentation tests of five sugars enabled the successful classification of 16 representative type strains into eight distinct groups. The grouping procedure was then applied to comparison of the coliform flora between food products and various locations in their processing environments. The consistency between each food and the tested locations was evaluated using the Jaccard index. The air conditioner and refrigeration room floor in factory A showed an index of 1.00, while the shaping machine in factory B showed an index of 0.98, indicating that these locations could be contamination sources. The validity of our results was confirmed by randomly amplified polymorphic DNA, which showed 100% matched profiles between the air conditioner and the food in factory A, and highly matched profiles between the machine and the food in factory B. This method for comparing the coliform flora between food and environments has the potential to be a reliable tracing tool for various food industries.

Processing capacity under perceptual and cognitive load: a closer look at load theory.

PubMed

Fitousi, Daniel; Wenger, Michael J

2011-06-01

Variations in perceptual and cognitive demands (load) play a major role in determining the efficiency of selective attention. According to load theory (Lavie, Hirst, Fockert, & Viding, 2004) these factors (a) improve or hamper selectivity by altering the way resources (e.g., processing capacity) are allocated, and (b) tap resources rather than data limitations (Norman & Bobrow, 1975). Here we provide an extensive and rigorous set of tests of these assumptions. Predictions regarding changes in processing capacity are tested using the hazard function of the response time (RT) distribution (Townsend & Ashby, 1978; Wenger & Gibson, 2004). The assumption that load taps resource rather than data limitations is examined using measures of sensitivity and bias drawn from signal detection theory (Swets, 1964). All analyses were performed at two levels: the individual and the aggregate. Hypotheses regarding changes in processing capacity were confirmed at the level of the aggregate. Hypotheses regarding resource and data limitations were not completely supported at either level of analysis. And in all of the analyses, we observed substantial individual differences. In sum, the results suggest a need to expand the theoretical vocabulary of load theory, rather than a need to discard it.

Long-term trihexyphenidyl exposure alters neuroimmune response and inflammation in aging rat: relevance to age and Alzheimer's disease.

PubMed

Huang, Yuqi; Zhao, Zhe; Wei, Xiaoli; Zheng, Yong; Yu, Jianqiang; Zheng, Jianquan; Wang, Liyun

2016-07-01

Clinical studies have shown an association between long-term anticholinergic (AC) drug exposure and Alzheimer's disease (AD) pathogenesis, which has been primarily investigated in Parkinson's disease (PD). However, long-term AC exposure as a risk factor for developing neurodegenerative disorders and the exact mechanisms and potential for disease progression remain unclear. Here, we have addressed the issue using trihexyphenidyl (THP), a commonly used AC drug in PD patients, to determine if THP can accelerate AD-like neurodegenerative progression and study potential mechanisms involved. Male Sprague-Dawley rats (SD) were intraperitoneally injected with THP (0.3 and 1.0 mg/kg) or normal saline (NS) for 7 months. Alterations in cognitive and behavioral performance were assessed using the Morris water maze (MWM) and open field tests. After behavior tests, whole genome oligo microarrays, quantitative real-time reverse transcription-polymerase chain reaction (qRT-PCR), immunohistochemistry, and immunofluorescence-confocal were used to investigate the global mechanisms underlying THP-induced neuropathology with aging. Compared with NS controls, the MWM test results showed that THP-treated rats exhibited significantly extended mean latencies during the initial 3 months of testing; however, this behavioral deficit was restored between the fourth and sixth month of MWM testing. The same tendencies were confirmed by MWM probe and open field tests. Gene microarray analysis identified 68 (47 %) upregulated and 176 (53 %) downregulated genes in the "THP-aging" vs. "NS-aging" group. The most significant populations of genes downregulated by THP were the immune response-, antigen processing and presentation-, and major histocompatibility complex (MHC)-related genes, as validated by qRT-PCR. The decreased expression of MHC class I in THP-treated aging brains was confirmed by confocal analysis. Notably, long-term THP treatment primed hippocampal and cortical microglia to undergo an inflammatory phenotypic switch, causing microgliosis and microglia activation, which were positively accompanied by pathological misfolded tau lesions. Our findings suggest that immune response and neuroinflammation represent a pivotal mechanism in THP-induced AD-like neuropathology processes with long-term exposure to AC drugs.

Recognition memory span in autopsy-confirmed Dementia with Lewy Bodies and Alzheimer's Disease.

PubMed

Salmon, David P; Heindel, William C; Hamilton, Joanne M; Vincent Filoteo, J; Cidambi, Varun; Hansen, Lawrence A; Masliah, Eliezer; Galasko, Douglas

2015-08-01

Evidence from patients with amnesia suggests that recognition memory span tasks engage both long-term memory (i.e., secondary memory) processes mediated by the diencephalic-medial temporal lobe memory system and working memory processes mediated by fronto-striatal systems. Thus, the recognition memory span task may be particularly effective for detecting memory deficits in disorders that disrupt both memory systems. The presence of unique pathology in fronto-striatal circuits in Dementia with Lewy Bodies (DLB) compared to AD suggests that performance on the recognition memory span task might be differentially affected in the two disorders even though they have quantitatively similar deficits in secondary memory. In the present study, patients with autopsy-confirmed DLB or AD, and Normal Control (NC) participants, were tested on separate recognition memory span tasks that required them to retain increasing amounts of verbal, spatial, or visual object (i.e., faces) information across trials. Results showed that recognition memory spans for verbal and spatial stimuli, but not face stimuli, were lower in patients with DLB than in those with AD, and more impaired relative to NC performance. This was despite similar deficits in the two patient groups on independent measures of secondary memory such as the total number of words recalled from long-term storage on the Buschke Selective Reminding Test. The disproportionate vulnerability of recognition memory span task performance in DLB compared to AD may be due to greater fronto-striatal involvement in DLB and a corresponding decrement in cooperative interaction between working memory and secondary memory processes. Assessment of recognition memory span may contribute to the ability to distinguish between DLB and AD relatively early in the course of disease. Copyright © 2015 Elsevier Ltd. All rights reserved.

Recognition Memory Span in Autopsy-Confirmed Dementia with Lewy Bodies and Alzheimer’s Disease

PubMed Central

Salmon, David P.; Heindel, William C.; Hamilton, Joanne M.; Filoteo, J. Vincent; Cidambi, Varun; Hansen, Lawrence A.; Masliah, Eliezer; Galasko, Douglas

2016-01-01

Evidence from patients with amnesia suggests that recognition memory span tasks engage both long-term memory (i.e., secondary memory) processes mediated by the diencephalic-medial temporal lobe memory system and working memory processes mediated by fronto-striatal systems. Thus, the recognition memory span task may be particularly effective for detecting memory deficits in disorders that disrupt both memory systems. The presence of unique pathology in fronto-striatal circuits in Dementia with Lewy Bodies (DLB) compared to AD suggests that performance on the recognition memory span task might be differentially affected in the two disorders even though they have quantitatively similar deficits in secondary memory. In the present study, patients with autopsy-confirmed DLB or AD, and normal control (NC) participants, were tested on separate recognition memory span tasks that required them to retain increasing amounts of verbal, spatial, or visual object (i.e., faces) information across trials. Results showed that recognition memory spans for verbal and spatial stimuli, but not face stimuli, were lower in patients with DLB than in those with AD, and more impaired relative to NC performance. This was despite similar deficits in the two patient groups on independent measures of secondary memory such as the total number of words recalled from Long-Term Storage on the Buschke Selective Reminding Test. The disproportionate vulnerability of recognition memory span task performance in DLB compared to AD may be due to greater fronto-striatal involvement in DLB and a corresponding decrement in cooperative interaction between working memory and secondary memory processes. Assessment of recognition memory span may contribute to the ability to distinguish between DLB and AD relatively early in the course of disease. PMID:26184443

49 CFR 40.253 - What are the procedures for conducting an alcohol confirmation test?

Code of Federal Regulations, 2010 CFR

2010-10-01

... confirmation test and show the reading to the employee. (1) If the reading is 0.00, the test may proceed. If the reading is greater than 0.00, you must conduct another air blank. (2) If the reading on the second air blank is 0.00, the test may proceed. If the reading is greater than 0.00, you must take the EBT...

49 CFR 40.253 - What are the procedures for conducting an alcohol confirmation test?

Code of Federal Regulations, 2011 CFR

2011-10-01

... confirmation test and show the reading to the employee. (1) If the reading is 0.00, the test may proceed. If the reading is greater than 0.00, you must conduct another air blank. (2) If the reading on the second air blank is 0.00, the test may proceed. If the reading is greater than 0.00, you must take the EBT...

Phyto-synthesis of silver nanoscale particles using Morinda citrifolia L. and its inhibitory activity against human pathogens.

PubMed

Sathishkumar, Gnanasekar; Gobinath, Chandrakasan; Karpagam, Karuppiah; Hemamalini, Vedagiri; Premkumar, Kumpati; Sivaramakrishnan, Sivaperumal

2012-06-15

Leaf extract of Morinda citrifolia L. was assessed for the synthesis of silver nanoscale particles under different temperature and reaction time. Synthesized nanoscale (MCAgNPs) particles were confirmed by analysing the excitation of surface plasmon resonance (SPR) using UV-visible spectrophotometer at 420 nm. Further SEM, HRTEM analysis confirmed the range of particle size between 10 and 60 nm and SEAD pattern authorizes the face centered cubic (fcc) crystalline nature of the MCAgNPs. Fourier transform infrared spectrum (FTIR) of synthesized MCAgNPs confirms the presence of high amount of phenolic compounds in the plant extract which may possibly influence the reduction process and stabilization of nanoparticles. Further, inhibitory activity of MCAgNPs and plant extract were tested against human pathogens like Eschericia coli, Pseudomonas aeroginosa, Klebsiella pneumoniae, Enterobacter aerogenes, Bacillus cereus and Enterococci sp. The results indicated that the MCAgNPs showed moderate inhibitory actions against human pathogens than crude plant extract, demonstrating its antimicrobial value against pathogenic diseases. Copyright © 2012 Elsevier B.V. All rights reserved.

Modelling social interaction as perceptual crossing: an investigation into the dynamics of the interaction process

NASA Astrophysics Data System (ADS)

Froese, Tom; Di Paolo, Ezequiel A.

2010-03-01

This paper continues efforts to establish a mutually informative dialogue between psychology and evolutionary robotics in order to investigate the dynamics of social interaction. We replicate a recent simulation model of a minimalist experiment in perceptual crossing and confirm the results with significantly simpler artificial agents. A series of psycho-physical tests of their behaviour informs a hypothetical circuit model of their internal operation. However, a detailed study of the actual internal dynamics reveals this circuit model to be unfounded, thereby offering a tale of caution for those hypothesising about sub-personal processes in terms of behavioural observations. In particular, it is shown that the behaviour of the agents largely emerges out of the interaction process itself rather than being an individual achievement alone. We also extend the original simulation model in two novel directions in order to test further the extent to which perceptual crossing between agents can self-organise in a robust manner. These modelling results suggest new hypotheses that can become the basis for further psychological experiments.

Evaporation behavior of lithium, potassium, uranium and rare earth chlorides in pyroprocessing

NASA Astrophysics Data System (ADS)

Jang, Junhyuk; Kim, Tackjin; Park, Sungbin; Kim, Gha-Young; Kim, Sihyoung; Lee, Sungjai

2017-12-01

The evaporation behaviors of Li, K, U, and rare earth (RE) chlorides were examined for the cathode process in pyroprocessing. The evaporation temperatures of the chlorides were evaluated in vacuum by measuring the weight decrease. In addition, an evaporation test up to 1473 K of the cathode process using a surrogate mixture of uranium and chlorides was conducted. It was found that LiCl evaporated more readily than the other chlorides. The weight of LiCl was rapidly decreased at temperatures above 981 K, while that of KCl was decreased above 1035 K, indicating the evaporation. UCl3 evaporated at temperatures above 1103 K. RE chlorides showed a similar evaporation behavior, evaporating first at 1158 K then rapidly evaporating at temperatures above 1230 K. Thus, the order of evaporation with increasing temperature was found to be LiCl < KCl < UCl3 < RE chlorides, with different RE chlorides evaporating at similar temperature. The surrogate test confirmed the observed evaporation trend of the chlorides during the cathode process, and revealed that the contamination of uranium remains by the back-reaction of RE chlorides is negligible.

Development of a neutron measurement system in unified non-destructive assay for the PRIDE facility

NASA Astrophysics Data System (ADS)

Seo, Hee; Park, Se-Hwan; Won, Byung-Hee; Ahn, Seong-Kyu; Shin, Hee-Sung; Na, Sang-Ho; Song, Dae-Yong; Kim, Ho-Dong; Lee, Seung Kyu

2013-12-01

The Korea Atomic Energy Research Institute (KAERI) has made an effort to develop pyroprocessing technology to resolve an on-going problem in Korea, i.e., the management of spent nuclear fuels. To this end, a test-bed facility for pyroprocessing, called PRIDE (PyRoprocessing Integrated inactive DEmonstration facility), is being constructed at KAERI. The main objective of PRIDE is to evaluate the performance of the unit processes, remote operation, maintenance, and proliferation resistance. In addition, integrating all unit processes into a one-step process is also one of the main goals. PRIDE can also provide a good opportunity to test safeguards instrumentations for a pyroprocessing facility such as nuclear material accounting devices, surveillance systems, radiation monitoring systems, and process monitoring systems. In the present study, a non-destructive assay (NDA) system for the testing of nuclear material accountancy of PRIDE was designed by integrating three different NDA techniques, i.e., neutron, gamma-ray, and mass measurements. The developed neutron detection module consists of 56 3He tubes and 16 AMPTEK A111 signal processing circuits. The amplifiers were matched in terms of the gain and showed good uniformity after a gain-matching procedure (%RSD=0.37%). The axial and the radial efficiency distributions within the cavity were then measured using a 252Cf neutron source and were compared with the MCNPX calculation results. The measured efficiency distributions showed excellent agreement with the calculations, which confirmed the accuracy of the MCNPX model of the system.

Laboratory medicine handoff gaps experienced by primary care practices: A report from the shared networks of collaborative ambulatory practices and partners (SNOCAP).

PubMed

West, David R; James, Katherine A; Fernald, Douglas H; Zelie, Claire; Smith, Maxwell L; Raab, Stephen S

2014-01-01

The majority of errors in laboratory medicine testing are thought to occur in the pre- and postanalytic testing phases, and a large proportion of these errors are secondary to failed handoffs. Because most laboratory tests originate in ambulatory primary care, understanding the gaps in handoff processes within and between laboratories and practices is imperative for patient safety. Therefore, the purpose of this study was to understand, based on information from primary care practice personnel, the perceived gaps in laboratory processes as a precursor to initiating process improvement activities. A survey was used to assess perceptions of clinicians, staff, and management personnel of gaps in handoffs between primary care practices and laboratories working in 21 Colorado primary care practices. Data were analyzed to determine statistically significant associations between categorical variables. In addition, qualitative analysis of responses to open-ended survey questions was conducted. Primary care practices consistently reported challenges and a desire/need to improve their efforts to systematically track laboratory test status, confirm receipt of laboratory results, and report results to patients. Automated tracking systems existed in roughly 61% of practices, and all but one of those had electronic health record-based tracking systems in place. One fourth of these electronic health record-enabled practices expressed sufficient mistrust in these systems to warrant the concurrent operation of an article-based tracking system as backup. Practices also reported 12 different procedures used to notify patients of test results, varying by test result type. The results highlight the lack of standardization and definition of roles in handoffs in primary care laboratory practices for test ordering, monitoring, and receiving and reporting test results. Results also identify high-priority gaps in processes and the perceptions by practice personnel that practice improvement in these areas is needed. Commonalities in these areas warrant the development and support of tools for use in primary care settings. © Copyright 2014 by the American Board of Family Medicine.

Ensemble analyses improve signatures of tumour hypoxia and reveal inter-platform differences

PubMed Central

2014-01-01

Background The reproducibility of transcriptomic biomarkers across datasets remains poor, limiting clinical application. We and others have suggested that this is in-part caused by differential error-structure between datasets, and their incomplete removal by pre-processing algorithms. Methods To test this hypothesis, we systematically assessed the effects of pre-processing on biomarker classification using 24 different pre-processing methods and 15 distinct signatures of tumour hypoxia in 10 datasets (2,143 patients). Results We confirm strong pre-processing effects for all datasets and signatures, and find that these differ between microarray versions. Importantly, exploiting different pre-processing techniques in an ensemble technique improved classification for a majority of signatures. Conclusions Assessing biomarkers using an ensemble of pre-processing techniques shows clear value across multiple diseases, datasets and biomarkers. Importantly, ensemble classification improves biomarkers with initially good results but does not result in spuriously improved performance for poor biomarkers. While further research is required, this approach has the potential to become a standard for transcriptomic biomarkers. PMID:24902696

Does Temporal Integration of Face Parts Reflect Holistic Processing?

PubMed Central

Cheung, Olivia S.; Richler, Jennifer J.; Phillips, W. Stewart; Gauthier, Isabel

2011-01-01

We examined whether temporal integration of face parts reflects holistic processing or response interference. Participants learned to name two faces “Fred” and two “Bob”. At test, top and bottom halves of different faces formed composites and were presented briefly separated in time. Replicating prior findings (Singer & Sheinberg, 2006), naming of the target halves for aligned composites was slowed when the irrelevant halves were from faces with a different name compared to that from the original face. However, no interference was observed when the irrelevant halves had identical names as the target halves but came from different learned faces, arguing against a true holistic effect. Instead, response interference was obtained when the target halves briefly preceded the irrelevant halves. Experiment 2 confirmed a double-dissociation between holistic processing vs. response interference for intact faces vs. temporally separated face halves, suggesting that simultaneous presentation of facial information is critical for holistic processing. PMID:21327378

Description and testing of the Geo Data Portal: Data integration framework and Web processing services for environmental science collaboration

USGS Publications Warehouse

Blodgett, David L.; Booth, Nathaniel L.; Kunicki, Thomas C.; Walker, Jordan I.; Viger, Roland J.

2011-01-01

Interest in sharing interdisciplinary environmental modeling results and related data is increasing among scientists. The U.S. Geological Survey Geo Data Portal project enables data sharing by assembling open-standard Web services into an integrated data retrieval and analysis Web application design methodology that streamlines time-consuming and resource-intensive data management tasks. Data-serving Web services allow Web-based processing services to access Internet-available data sources. The Web processing services developed for the project create commonly needed derivatives of data in numerous formats. Coordinate reference system manipulation and spatial statistics calculation components implemented for the Web processing services were confirmed using ArcGIS 9.3.1, a geographic information science software package. Outcomes of the Geo Data Portal project support the rapid development of user interfaces for accessing and manipulating environmental data.

Diatom-sedimentation feedback generates a self-organized geomorphic landscape on intertidal mudflats (Invited)

NASA Astrophysics Data System (ADS)

van de Koppel, J.; Weerman, E.; Herman, P.

2010-12-01

During spring, intertidal flats can exhibit strikingly regular spatial patterns of diatom-covered hummocks alternating with almost bare, water-filled hollows. We hypothesize that 1) the formation of this geomorphic landscape is caused by a strong interaction between benthic diatoms and sediment dynamics, inducing spatial self-organization, and 2) that self-organization affects ecosystem functioning by increasing the net average sedimentation on the tidal flat. We present a combined empirical and mathematical study to test the first hypothesis. We determined how the sediment erosion threshold varied with diatom cover and elevation. Our results were incorporated into a mathematical model to investigate whether the proposed mechanism could explain the formation of the observed patterns. Our mathematical model confirmed that the interaction between sedimentation, diatom growth and water redistribution could induce the formation of regular patterns on the intertidal mudflat. The model predicts that areas exhibiting spatially-self-organized patterns have increased sediment accretion and diatom biomass compared with areas lacking spatial patterns. We tested this prediction by following the sediment elevation during the season on both patterned and unpatterned parts of the mudflat. The results of our study confirmed our model prediction, as more sediment was found to accumulate in patterned parts of the mudflat, revealing how self-organization affected the functioning of mudflat ecosystems. Our study on intertidal mudflats provides a simple but clear-cut example of how the interaction between biological and geomorphological processes, through the process of self-organization, induces a self-organized geomorphic landscape.

Observation of tendon repair in animal model using second-harmonic-generation microscopy

NASA Astrophysics Data System (ADS)

Hase, Eiji; Minamikawa, Takeo; Sato, Katsuya; Takahashi, Mitsuhiko; Yasui, Takashi

2016-03-01

Tendon rupture is a trauma difficult to recover the condition before injury. In previous researches, tensile test and staining method have been widely used to elucidate the mechanism of the repair process from the viewpoints of the mechanical property and the histological findings. However, since both methods are destructive and invasive, it is difficult to obtain both of them for the same sample. If both the mechanical property and the histological findings can be obtained from the same sample, one may obtain new findings regarding mechanisms of tendon repairing process. In this paper, we used second-harmonic-generation (SHG) microscopy, showing high selectivity and good image contrast to collagen molecules as well as high spatial resolution, optical three-dimensional sectioning, deep penetration, and without additional staining. Since SHG light intensity sensitively reflects the structural maturity of collagen molecule and its aggregates, it will be a good indicator for the repairing degree of the ruptured tendon. From comparison of SHG images between the 4-weeks-repaired tendon and the sound tendon in the animal model, we confirmed that SHG light intensity of the repaired tendon was significantly lower than that of the sound tendon, indicating that the collagen structure in the repaired tendon is still immature. Furthermore, we performed both SHG imaging and the tensile test for the same sample, and confirmed a correlation between them. This result shows a potential of SHG light for an indicator of the histological and mechanical recovery of the ruptured tendon.

Biocompatibility of hydroxyapatite scaffolds processed by lithography-based additive manufacturing.

PubMed

Tesavibul, Passakorn; Chantaweroad, Surapol; Laohaprapanon, Apinya; Channasanon, Somruethai; Uppanan, Paweena; Tanodekaew, Siriporn; Chalermkarnnon, Prasert; Sitthiseripratip, Kriskrai

2015-01-01

The fabrication of hydroxyapatite scaffolds for bone tissue engineering applications by using lithography-based additive manufacturing techniques has been introduced due to the abilities to control porous structures with suitable resolutions. In this research, the use of hydroxyapatite cellular structures, which are processed by lithography-based additive manufacturing machine, as a bone tissue engineering scaffold was investigated. The utilization of digital light processing system for additive manufacturing machine in laboratory scale was performed in order to fabricate the hydroxyapatite scaffold, of which biocompatibilities were eventually evaluated by direct contact and cell-culturing tests. In addition, the density and compressive strength of the scaffolds were also characterized. The results show that the hydroxyapatite scaffold at 77% of porosity with 91% of theoretical density and 0.36 MPa of the compressive strength are able to be processed. In comparison with a conventionally sintered hydroxyapatite, the scaffold did not present any cytotoxic signs while the viability of cells at 95.1% was reported. After 14 days of cell-culturing tests, the scaffold was able to be attached by pre-osteoblasts (MC3T3-E1) leading to cell proliferation and differentiation. The hydroxyapatite scaffold for bone tissue engineering was able to be processed by the lithography-based additive manufacturing machine while the biocompatibilities were also confirmed.

Study on Pot Forming of Induction Heater Type Rice Cookers by Forging Cast Process

NASA Astrophysics Data System (ADS)

Ohnishi, Masayuki; Yamaguchi, Mitsugi; Ohashi, Osamu

This paper describes a study result on pot fabrication by the forging cast process of stainless steel with aluminum. Rice cooked with the new bowl-shaped pot for the induction heater type rice cookers is better tasting than rice cooked with the conventional cylindrical one, due to the achievement of better heat conduction and convection. The conventional pot is made of the clad sheet, consisting of stainless steel and aluminum. However, it is rather difficult to form a bowl shape from the clad sheet, primarily due to the problem of a material spring back. The fabrication of a new type of a pot was made possible by means of the adoption of a forging cast process instead of the clad sheet. In this process, iron powder is inserted between stainless steel and aluminum in order to alleviate the large difference on the coefficient of expansion between each material. It was made clear that the application of two kinds of iron particle, namely 10 μm size powder on the stainless steel side and 44 μm on the aluminum side, enables the joints to become strong enough. The joint strength of the new pot by this fabrication process was confirmed by the tests of the shear strength and the fatigue tests together with the stress analysis.

The value of losartan suppression test in the confirmatory diagnosis of primary aldosteronism in patients over 50 years old.

PubMed

Kuo, Chin-Chi; Balakrishnan, Poojitha; Hsein, Yenh-Chen; Wu, Vin-Cent; Chueh, Shih-Chieh Jeff; Chen, Yung-Ming; Wu, Kwan-Dun; Wang, Ming-Jiuh

2015-09-01

The diagnosis of primary aldosteronism (PA) among the older-aged population has posed a crucial challenge. Among patients over 50 years old, this trial assessed comparability of the performance of two PA diagnostic tests: losartan and captopril suppression tests. A post-hoc subgroup analysis from a prospective cohort was conducted by the TAIPAI (Taiwan Primary Aldosteronism Investigation) group between July 2003 and July 2006. Of the 160 patients in the cohort, 60 patients over 50 years old received captopril and losartan tests to confirm PA. Among the 60 patients over 50 years old, 31 patients had PA confirmed by standardized protocol. The area under the receiver-operating characteristic (ROC) curve for post-captopril aldosterone was significantly less than that for post-losartan plasma aldosterone concentration (PAC) (0.87 vs 0.94, p=0.02). Using the aldosterone-renin ratio (ARR)>35 with PAC>10 ng/dl, the specificity was 82.76% vs 93.1% and the sensitivity was 77.42% vs 87.10% for the captopril and losartan tests, respectively. The equivalence between the two tests were confirmed by the exact McNemar's test (p=1.0). The losartan test showed comparable accuracy to confirm PA. Verification of this "elderly-friendly" confirmatory test will be the first step to prepare a specific diagnostic model of PA for the older-aged population. © The Author(s) 2014.

The Value of Losartan Suppression Test in the Confirmatory Diagnosis of Primary Aldosteronism in Patients Over 50 Years Old

PubMed Central

Kuo, Chin-Chi; Balakrishnan, Poojitha; Hsein, Yenh-Chen; Wu, Vin-Cent; Chueh, Shih-Chieh Jeff; Chen, Yung-Ming; Wu, Kwan-Dun; Wang, Ming-Jiuh

2013-01-01

Objective The diagnosis of primary aldosteronism (PA) among the older-aged population has posed a crucial challenge. Among patients over 50 years old, this trial assessed comparability of the performance of two PA diagnostic tests: losartan and captoril suppression tests. Methods A post-hoc subgroup analysis from a prospective cohort was conducted by TAIPAI (Taiwan Primary Aldosteornism Investigation) group between July 2003 and July 2006. Of the 160 patients in the cohort, 60 patients over 50 years received captopril and losartan tests to confirm PA. Results Among the 60 patients over 50 years old, 31 patients had PA confirmed by standardized protocol. The area under the receiver-operating characteristic (ROC) curve of the post-captopril aldosterone was significantly less than that of the post-losartan plasma aldosterone concentration (0.87 vs. 0.94, p = 0.02). Using ARR>35 with PAC>10 ng/dL, the specificity was 82.76% vs. 93.1% and the sensitivity was 77.42% vs. 87.10% for the captopril and losartan tests, respectively. The equivalence between the two tests were confirmed by exact McNemar test (p= 1.0). Conclusion The losartan test showed comparable accuracy to confirm PA. Verification of this “elderly-friendly” confirmatory test will be the first step to prepare the specific diagnostic model of PA for older-aged population. PMID:25031295

Auditory Temporal Processing Deficits in Chronic Stroke: A Comparison of Brain Damage Lateralization Effect.

PubMed

Jafari, Zahra; Esmaili, Mahdiye; Delbari, Ahmad; Mehrpour, Masoud; Mohajerani, Majid H

2016-06-01

There have been a few reports about the effects of chronic stroke on auditory temporal processing abilities and no reports regarding the effects of brain damage lateralization on these abilities. Our study was performed on 2 groups of chronic stroke patients to compare the effects of hemispheric lateralization of brain damage and of age on auditory temporal processing. Seventy persons with normal hearing, including 25 normal controls, 25 stroke patients with damage to the right brain, and 20 stroke patients with damage to the left brain, without aphasia and with an age range of 31-71 years were studied. A gap-in-noise (GIN) test and a duration pattern test (DPT) were conducted for each participant. Significant differences were found between the 3 groups for GIN threshold, overall GIN percent score, and DPT percent score in both ears (P ≤ .001). For all stroke patients, performance in both GIN and DPT was poorer in the ear contralateral to the damaged hemisphere, which was significant in DPT and in 2 measures of GIN (P ≤ .046). Advanced age had a negative relationship with temporal processing abilities for all 3 groups. In cases of confirmed left- or right-side stroke involving auditory cerebrum damage, poorer auditory temporal processing is associated with the ear contralateral to the damaged cerebral hemisphere. Replication of our results and the use of GIN and DPT tests for the early diagnosis of auditory processing deficits and for monitoring the effects of aural rehabilitation interventions are recommended. Copyright © 2016 National Stroke Association. Published by Elsevier Inc. All rights reserved.

Contributions to ultrasound monitoring of the process of milk curdling.

PubMed

Jiménez, Antonio; Rufo, Montaña; Paniagua, Jesús M; Crespo, Abel T; Guerrero, M Patricia; Riballo, M José

2017-04-01

Ultrasound evaluation permits the state of milk being curdled to be determined quickly and cheaply, thus satisfying the demands faced by today's dairy product producers. This paper describes the non-invasive ultrasonic method of in situ monitoring the changing physical properties of milk during the renneting process. The basic objectives of the study were, on the one hand, to confirm the usefulness of conventional non-destructive ultrasonic testing (time-of-flight and attenuation of the ultrasound waves) in monitoring the process in the case of ewe's milk, and, on the other, to include other ultrasound parameters which have not previously been considered in studies on this topic, in particular, parameters provided by the Fast Fourier Transform technique. The experimental study was carried out in a dairy industry environment on four 52-l samples of raw milk in which were immersed 500kHz ultrasound transducers. Other physicochemical parameters of the raw milk (pH, dry matter, protein, Gerber fat test, and lactose) were measured, as also were the pH and temperature of the curdled samples simultaneously with the ultrasound tests. Another contribution of this study is the linear correlation analysis of the aforementioned ultrasound parameters and the physicochemical properties of the curdled milk. Copyright © 2017 Elsevier B.V. All rights reserved.

Robot-Assisted Fracture Surgery: Surgical Requirements and System Design.

PubMed

Georgilas, Ioannis; Dagnino, Giulio; Tarassoli, Payam; Atkins, Roger; Dogramadzi, Sanja

2018-03-09

The design of medical devices is a complex and crucial process to ensure patient safety. It has been shown that improperly designed devices lead to errors and associated accidents and costs. A key element for a successful design is incorporating the views of the primary and secondary stakeholders early in the development process. They provide insights into current practice and point out specific issues with the current processes and equipment in use. This work presents how information from a user-study conducted in the early stages of the RAFS (Robot Assisted Fracture Surgery) project informed the subsequent development and testing of the system. The user needs were captured using qualitative methods and converted to operational, functional, and non-functional requirements based on the methods derived from product design and development. This work presents how the requirements inform a new workflow for intra-articular joint fracture reduction using a robotic system. It is also shown how the various elements of the system are developed to explicitly address one or more of the requirements identified, and how intermediate verification tests are conducted to ensure conformity. Finally, a validation test in the form of a cadaveric trial confirms the ability of the designed system to satisfy the aims set by the original research question and the needs of the users.

Confirming expectations in asymmetric and symmetric social hypothesis testing.

PubMed

Rusconi, Patrice; Sacchi, Simona; Toscano, Armando; Cherubini, Paolo

2012-01-01

This article examines individuals' expectations in a social hypothesis testing task. Participants selected questions from a list to investigate the presence of personality traits in a target individual. They also identified the responses that they expected to receive and the likelihood of the expected responses. The results of two studies indicated that when people asked questions inquiring about the hypothesized traits that did not entail strong a priori beliefs, they expected to find evidence confirming the hypothesis under investigation. These confirming expectations were more pronounced for symmetric questions, in which the diagnosticity and frequency of the expected evidence did not conflict. When the search for information was asymmetric, confirming expectations were diminished, likely as a consequence of either the rareness or low diagnosticity of the hypothesis-confirming outcome. We also discuss the implications of these findings for confirmation bias.

Towards Risk-Based Test Protocols: Estimating the Contribution of Intensive Testing to the UK Bovine Tuberculosis Problem

PubMed Central

van Dijk, Jan

2013-01-01

Eradicating disease from livestock populations involves the balancing act of removing sufficient numbers of diseased animals without removing too many healthy individuals in the process. As ever more tests for bovine tuberculosis (BTB) are carried out on the UK cattle herd, and each positive herd test triggers more testing, the question arises whether ‘false positive’ results contribute significantly to the measured BTB prevalence. Here, this question is explored using simple probabilistic models of test behaviour. When the screening test is applied to the average UK herd, the estimated proportion of test-associated false positive new outbreaks is highly sensitive to small fluctuations in screening test specificity. Estimations of this parameter should be updated as a priority. Once outbreaks have been confirmed in screening-test positive herds, the following rounds of intensive testing with more sensitive, albeit less specific, tests are highly likely to remove large numbers of false positive animals from herds. Despite this, it is unlikely that significantly more truly infected animals are removed. BTB test protocols should become based on quantified risk in order to prevent the needless slaughter of large numbers of healthy animals. PMID:23717517

Microscopic or occult hematuria, when reflex testing is not good laboratory practice.

PubMed

Froom, Paul; Barak, Mira

2010-01-01

Consensus opinion suggests that hematuria found by dipstick and not confirmed on microscopic examination (<2 erythrocytes per high power field) signifies a false-positive reagent strip test result. Standard practice is to repeat the dipstick test several days later and if still positive to confirm by microscopic examination. If discordant results are obtained, experts recommend reflex testing for urinary myoglobin and hemoglobin concentrations. The question is whether or not this approach represents good laboratory practice. These recommendations are not evidence based. We conclude that the reference range for red blood cells on the reagent strip should be increased to 25x10(6) cells/L for young men, and 50x10(6) cells/L for the rest of the adult population, ranges consistent with flow cytometry reports. Confirmation reflex testing using tests that have inferior sensitivity, precision and probably accuracy is not recommended.

49 CFR 40.129 - What are the MRO's functions in reviewing laboratory confirmed non-negative drug test results?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 1 2013-10-01 2013-10-01 false What are the MRO's functions in reviewing laboratory confirmed non-negative drug test results? 40.129 Section 40.129 Transportation Office of the Secretary of Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Medical Review Officers and the Verification Proces...

Observed heavy precipitation increase confirms theory and early model

NASA Astrophysics Data System (ADS)

Fischer, E. M.; Knutti, R.

2016-12-01

Environmental phenomena are often first observed, and then explained or simulated quantitatively. The complexity and diversity of processes, the range of scales involved, and the lack of first principles to describe many processes make it challenging to predict conditions beyond the ones observed. Here we use the intensification of heavy precipitation as a counterexample, where seemingly complex and potentially computationally intractable processes to first order manifest themselves in simple ways: the intensification of heavy precipitation is now emerging in the observed record across many regions of the world, confirming both theory and a variety of model predictions made decades ago, before robust evidence arose from observations. We here compare heavy precipitation changes over Europe and the contiguous United States across station series and gridded observations, theoretical considerations and multi-model ensembles of GCMs and RCMs. We demonstrate that the observed heavy precipitation intensification aggregated over large areas agrees remarkably well with Clausius-Clapeyron scaling. The observed changes in heavy precipitation are consistent yet somewhat larger than predicted by very coarse resolution GCMs in the 1980s and simulated by the newest generation of GCMs and RCMs. For instance the number of days with very heavy precipitation over Europe has increased by about 45% in observations (years 1981-2013 compared to 1951-1980) and by about 25% in the model average in both GCMs and RCMs, although with substantial spread across models and locations. As the anthropogenic climate signal strengthens, there will be more opportunities to test climate predictions for other variables against observations and across a hierarchy of different models and theoretical concepts. *Fischer, E.M., and R. Knutti, 2016, Observed heavy precipitation increase confirms theory and early models, Nature Climate Change, in press.

Oxide ceramic femoral heads contribute to the oxidation of polyethylene liners in artificial hip joints.

PubMed

Pezzotti, Giuseppe; Zhu, Wenliang; Sugano, Nobuhiko; Marin, Elia; Yamamoto, Kengo; Nishiike, Naomichi; Hori, Tsubasa; Rondinella, Alfredo; McEntire, Bryan J; Bock, Ryan; Sonny Bal, B

2018-06-01

Experimental evidence demonstrates that a loss of stoichiometry at the surface of oxide bioceramic femoral heads enhances the oxidation rate of polyethylene acetabular liners in artificial hip joints. Contradicting the common notion that ceramics are bioinert, three independent experiments confirmed substantial chemical interactions between the ceramic femoral heads and their polyethylene counterparts. The experiments reported herein included hydrothermal tests, frictional tests, and hip-simulator experiments. It was discovered that oxide and non-oxide femoral heads differently affected the oxidation processes at the surface of the polyethylene liners, all other testing parameters being equal. Analytical data from X-ray photoelectron (XPS), cathodoluminescence (CL), Fourier-transform infrared (FTIR), and Raman spectroscopies unequivocally and consistently showed that the oxidation rate of polyethylene liners was greater when coupled with oxide as opposed to non-oxide ceramic heads. XPS analyses of O-Al-O bond fractions at the surface of a zirconia-toughened alumina (ZTA) short-term (20 months in vivo) femoral heads retrieval showed a ~50% reduction in favor of oxygen vacancy O-Al-V O and hydroxylated Al-O-H bonds. Off-stoichiometry drifts were confirmed in vitro under both static and dynamic conditions. They triggered oxidation and tangibly affected an advanced highly cross-linked sequentially irradiated and annealed ultra-high molecular weight polyethylene (UHMWPE) liner (increase in oxidation index up to ΔOI~1.2 after 5 × 10 5 cycles under dynamic swing conditions). Second-generation UHMWPE liners infused with vitamin E were also affected by the free flow of oxygen from the oxide femoral heads, although to a lesser extent. The fundamental findings of this study, which were also confirmed on retrievals, call for revised standards in material design and testing. Adopting these new criteria will provide an improved understanding of the importance of off-stoichiometry at the head/liner interface and may lead to significant extensions in artificial joint lifetimes. Copyright © 2018 Elsevier Ltd. All rights reserved.

Repetition priming with Japanese Kana scripts in word-fragment completion.

PubMed

Komatsu, S; Naito, M

1992-03-01

Manipulating two types of Japanese Kana script, Katakana and Hiragana, we examined the effects of a script change between study and test on later word-fragment completion. Throughout three experiments, materials were composed of foreign loan nouns normally written in Katakana, but not in Hiragana, according to approved usage in Japanese. Experiment 1 demonstrated the reliable size of cross-script priming between Katakana and Hiragana. In Experiment 2, cross-modal priming was substantial when modality of presentation was changed from auditory to visual. In Experiment 3, generating a target word from its definition induced priming comparable in size to that in the prior reading condition. These results have been confirmed in the Hiragana test, as well as in the Katakana test, thereby suggesting that some conceptual and modality-independent processes may also mediate repetition priming.

Application of the BAX for screening/genus Listeria polymerase chain reaction system for monitoring Listeria species in cold-smoked fish and in the smoked fish processing environment.

PubMed

Norton, D M; McCamey, M; Boor, K J; Wiedmann, M

2000-03-01

The cold-smoked fish industry was used as a model for the development of a system for monitoring Listeria spp. in foods and in the food processing environment. A total of 214 samples including raw fish, fish during the cold-smoking process, finished product, and environmental samples were collected from three processing facilities over two visits to each facility. Samples were screened for Listeria spp. using the BAX for Screening/genus Listeria polymerase chain reaction system (PCR) and by culture. Listeria spp., confirmed by the API Listeria test strip or by a PCR assay targeting the L. monocytogenes hlyA gene, were isolated from a total of 89 (41.6%) samples. Of these, 80 samples also tested positive for Listeria spp. using the BAX system. Specifically, 42 (55.3%) environmental samples (n = 76), 11 (25.6%) raw materials samples (n = 43), 20 (35.1%) samples from fish in various stages of processing (n = 57), and 7 (18.4%) finished product samples (n = 38) tested positive for Listeria spp. using the BAX system. Five (4.0%) of the 125 culture-negative samples yielded BAX system-positive results. Listeria isolates from each of nine culture-positive/BAX system-negative samples yielded a positive reaction when tested in pure culture by the BAX system, suggesting that our false-negative results were likely due to the presence of low Listeria numbers in the initial enrichment as opposed to nonreacting isolates. The employment of alternative enrichment protocols, such as the two-step enrichment recommended by the manufacturer, may increase the sensitivity of the assay.

Romer Labs RapidChek®Listeria monocytogenes Test System for the Detection of L. monocytogenes on Selected Foods and Environmental Surfaces.

PubMed

Juck, Gregory; Gonzalez, Verapaz; Allen, Ann-Christine Olsson; Sutzko, Meredith; Seward, Kody; Muldoon, Mark T

2018-04-27

The Romer Labs RapidChek ® Listeria monocytogenes test system (Performance Tested Method ℠ 011805) was validated against the U.S. Department of Agriculture-Food Safety and Inspection Service Microbiology Laboratory Guidebook (USDA-FSIS/MLG), U.S. Food and Drug Association Bacteriological Analytical Manual (FDA/BAM), and AOAC Official Methods of Analysis ℠ (AOAC/OMA) cultural reference methods for the detection of L. monocytogenes on selected foods including hot dogs, frozen cooked breaded chicken, frozen cooked shrimp, cured ham, and ice cream, and environmental surfaces including stainless steel and plastic in an unpaired study design. The RapidChek method uses a proprietary enrichment media system, a 44-48 h enrichment at 30 ± 1°C, and detects L. monocytogenes on an immunochromatographic lateral flow device within 10 min. Different L. monocytogenes strains were used to spike each of the matrixes. Samples were confirmed based on the reference method confirmations and an alternate confirmation method. A total of 140 low-level spiked samples were tested by the RapidChek method after enrichment for 44-48 h in parallel with the cultural reference method. There were 88 RapidChek presumptive positives. One of the presumptive positives was not confirmed culturally. Additionally, one of the culturally confirmed samples did not exhibit a presumptive positive. No difference between the alternate confirmation method and reference confirmation method was observed. The respective cultural reference methods (USDA-FSIS/MLG, FDA/BAM, and AOAC/OMA) produced a total of 63 confirmed positive results. Nonspiked samples from all foods were reported as negative for L. monocytogenes by all methods. Probability of detection analysis demonstrated no significant differences in the number of positive samples detected by the RapidChek method and the respective cultural reference method.

SLURRY MIX EVAPORATOR BATCH ACCEPTABILITY AND TEST CASES OF THE PRODUCT COMPOSITION CONTROL SYSTEM WITH THORIUM AS A REPORTABLE ELEMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.

2010-10-07

The Defense Waste Processing Facility (DWPF), which is operated by Savannah River Remediation, LLC (SRR), has recently begun processing Sludge Batch 6 (SB6) by combining it with Frit 418 at a nominal waste loading (WL) of 36%. A unique feature of the SB6/Frit 418 glass system, as compared to the previous glass systems processed in DWPF, is that thorium will be a reportable element (i.e., concentrations of elemental thorium in the final glass product greater than 0.5 weight percent (wt%)) for the resulting wasteform. Several activities were initiated based upon this unique aspect of SB6. One of these was anmore » investigation into the impact of thorium on the models utilized in DWPF's Product Composition and Control System (PCCS). While the PCCS is described in more detail below, for now note that it is utilized by Waste Solidification Engineering (WSE) to evaluate the acceptability of each batch of material in the Slurry Mix Evaporator (SME) before this material is passed on to the melter. The evaluation employs models that predict properties associated with processability and product quality from the composition of vitrified samples of the SME material. The investigation of the impact of thorium on these models was conducted by Peeler and Edwards [1] and led to a recommendation that DWPF can process the SB6/Frit 418 glass system with ThO{sub 2} concentrations up to 1.8 wt% in glass. Questions also arose regarding the handling of thorium in the SME batch acceptability process as documented by Brown, Postles, and Edwards [2]. Specifically, that document is the technical bases of PCCS, and while Peeler and Edwards confirmed the reliability of the models, there is a need to confirm that the current implementation of DWPF's PCCS appropriately handles thorium as a reportable element. Realization of this need led to a Technical Task Request (TTR) prepared by Bricker [3] that identified some specific SME-related activities that the Savannah River National Laboratory (SRNL) was requested to conduct. SRNL issued a Task Technical and Quality Assurance (TT&QA) plan [4] in response to the SRR request. The conclusions provided in this report are that no changes need to be made to the SME acceptability process (i.e., no modifications to WSRC-TR-95-00364, Revision 5, are needed) and no changes need to be made to the Product Composition Control System (PCCS) itself (i.e. the spreadsheet utilized by Waste Solidification Engineering (WSE) for acceptability decisions does not require modification) in response to thorium becoming a reportable element for DWPF operations. In addition, the inputs and results for the two test cases requested by WSE for use in confirming the successful activation of thorium as a reportable element for DWPF operations during the processing of SB6 are presented in this report.« less

Implementation of the evidence review on best practice for confirming the correct placement of nasogastric tube in patients in an acute care hospital.

PubMed

Tho, Poh Chi; Mordiffi, Siti; Ang, Emily; Chen, Helen

2011-03-01

Nasogastric (NG) tube is a device passed through the gastrointestinal tract of patients for the purpose of feeding, gastric decompression and medication administration. However, a small risk involved in the process is that the tube may be misplaced into the trachea during insertion or may get displaced at a later stage, leading to disastrous results. Recent adverse incidences arising out of the misplacement of NG tube raised concerns among the nursing and medical community and the Patient Safety Officer of the hospital. The Evidence Based Nursing Unit, in collaboration with some of the key nursing leaders in nursing administration, was tasked to explore and institute the current best practice in confirming the correct placement of NG tube. The aim of this project was to institute the best practice to confirm the correct placement of NG tube in patients in an acute care hospital setting. The project comprised of a few stages. The first stage involved reviewing the existing recommendations and guidelines on the methods for checking correct NG tube placement. The second stage involved incorporation of the change of practice into the clinical setting. The final stage was to monitor and evaluate the impact of the new practice on the patients, nurses and other healthcare professionals. Evidence search from guidelines and journals supported the test that used pH indicator instead of the litmus test. There is no evidence that supports the method of auscultation and bubbling to confirm correct NG tube placement in the absence of aspirate. Radiology remains the 'gold standard' for checking correct NG tube placement. The revised method of NG tube placement and workflow was incorporated in the revised Standard Operating Procedures. A total of 17 roadshows were conducted to create awareness regarding the new method amongst the nurses, and the implementation of the revised method and workflow was commenced on 3 November 2008. The initial audit conducted 1 month after the practice change was implemented reported 26 (50%) observations of NG tube feeding in 26 audit wards. The key areas of practice change in feeding when tube placement was confirmed (84.6%) and proper testing of aspirate (76.9%) showed good compliance. The implementation of the change in the practice of confirming the correct placement of the NG tube in patients requires good coordination and a multidisciplinary team approach. © 2011 The Authors. International Journal of Evidence-Based Healthcare © 2011 The Joanna Briggs Institute.

Pathways from Autism Spectrum Disorder (ASD) Diagnosis to Genetic Testing

PubMed Central

Barton, Krysta S.; Tabor, Holly K.; Starks, Helene; Garrison, Nanibaa’ A.; Laurino, Mercy; Burke, Wylie

2017-01-01

Purpose This study examines challenges faced by families and health providers related to genetic testing for autism spectrum disorder (ASD). Methods This qualitative study of 14 parents and 15 health providers identified an unstandardized three-step process for families who pursue ASD genetic testing. Results Step 1 is the clinical diagnosis of ASD, confirmed by providers practicing alone or in a team. Step 2 is the offer of genetic testing to find an etiology. For those offered testing, step 3 involves the parents’ decision whether to pursue testing. Despite professional guidelines and recommendations, interviews describe considerable variability in approaches to genetic testing for ASD, a lack of consensus among providers, and questions about clinical utility. Many families in our study were unaware of the option for genetic testing; testing decisions by parents appear to be influenced by both provider recommendations and insurance coverage. Conclusion Consideration of genetic testing for ASD should take into account different views about the clinical utility of testing and variability in insurance coverage. Ideally, policy makers from the range of clinical specialties involved in ASD care should revisit policies to clarify the purpose of genetic testing for ASD and promote consensus about its appropriate use. PMID:29048417

Use of a smart phone based thermo camera for skin prick allergy testing: a feasibility study (Conference Presentation)

NASA Astrophysics Data System (ADS)

Barla, Lindi; Verdaasdonk, Rudolf M.; Rustemeyer, Thomas; Klaessens, John; van der Veen, Albert

2016-02-01

Allergy testing is usually performed by exposing the skin to small quantities of potential allergens on the inner forearm and scratching the protective epidermis to increase exposure. After 15 minutes the dermatologist performs a visual check for swelling and erythema which is subjective and difficult for e.g. dark skin types. A small smart phone based thermo camera (FLIR One) was used to obtain quantitative images in a feasibility study of 17 patients Directly after allergen exposure on the forearm, thermal images were captured at 30 seconds interval and processed to a time lapse movie over 15 minutes. Considering the 'subjective' reading of the dermatologist as golden standard, in 11/17 pts (65%) the evaluation of dermatologist was confirmed by the thermo camera including 5 of 6 patients without allergic response. In 7 patients thermo showed additional spots. Of the 342 sites tested, the dermatologist detected 47 allergies of which 28 (60%) were confirmed by thermo imaging while thermo imaging showed 12 additional spots. The method can be improved with user dedicated acquisition software and better registration between normal and thermal images. The lymphatic reaction seems to shift from the original puncture site. The interpretation of the thermal images is still subjective since collecting quantitative data is difficult due to motion patient during 15 minutes. Although not yet conclusive, thermal imaging shows to be promising to improve the sensitivity and selectivity of allergy testing using a smart phone based camera.

Certification testing as an acute naturalistic stressor for disaster dog handlers.

PubMed

Lit, L; Boehm, D; Marzke, S; Schweitzer, J; Oberbauer, A M

2010-09-01

USA Federal Disaster Canine Teams, consisting of a handler and a dog, are essential for locating survivors following a disaster. Certification, required by the Federal Emergency Management Agency Urban Search and Rescue organization, requires two successful mock searches. Confirmation of the certification testing process as an acute stressor might offer further opportunities to consider stress effects on handlers and dogs in a controlled environment. This study used a pretest-posttest design to evaluate relationships between salivary hormone concentrations (cortisol and testosterone) and subjective stress ratings in handlers and controls, handler assessments of stress in their dogs, and posttest temperature and pulse rate in dogs. Posttest, both subjective stress ratings and salivary cortisol concentration were higher in handlers than controls with both correlated to handlers' assessment of stress in their dogs. Handlers' posttest salivary cortisol concentration was associated with posttest dog pulse and temperature. Posttest cortisol concentration was lower in handlers who were successfully certified compared with those who failed, and was also lower in handlers whose primary occupation was "firefighter". Salivary testosterone concentrations increased from pretest to posttest in handlers but decreased in controls, and higher posttest handler testosterone concentration was negatively associated with posttest dog pulse rate. These findings confirm certification testing as an acute stressor, suggest a relationship between stress and performance moderated by occupation, and demonstrate an interaction between handler stress and dog physiological responses. This certification testing offers a controlled environment for targeted evaluation of effects of an acute naturalistic stressor on disaster dog handlers and dogs.

Double Aneuploidy Detected by Cell-Free DNA Testing and Confirmed by Fetal Tissue Analysis.

PubMed

Echague, Charlene G; Petersen, Scott M

2016-06-01

Double aneuploidies account for 0.21-2.8% of spontaneous abortions resulting from chromosomal abnormalities. Rarely, cell-free DNA testing detects multiple aneuploidies; however, to discern among maternal, placental, and fetal origin, further evaluation is required. A 49-year-old woman, gravida 5 para 0, underwent cell-free DNA testing at 11 4/7 weeks of gestation, which revealed a fetus that was high risk for trisomies 18 and 21. On ultrasonography at 14 weeks of gestation, she was diagnosed with a missed abortion and underwent surgical management. Fetal and placental tissues were sent for analysis and were positive for trisomies 18 and 21, confirming the results of cell-free DNA testing. Our case highlights the ability of cell-free DNA testing to recognize a double aneuploidy confirmed by fetal tissue analysis.

Raw milk consumption and health.

PubMed

Vranješ, Anka Popović; Popović, Milka; Jevtić, Marija

2015-01-01

Contrary to the safe practices of milk pasteurization or sterilization, which effectively reduce foodborne outbreaks incidence associated with raw milk and dairy products use, outbreaks caused by such products continue to occur. Despite this fact, a worldwide movement advocating for the rights of raw milk and cheese selling and consumption, due to their specific nutritive characteristics, has strengthened significantly in recent years. Traditional agricultural manufacturers from Serbia still sell products related to thermally unprocessed milk, such as cottage cheese and raw cream. In AP Vojvodina during the period of 1981-2010 a total of 179 foodborne outbreaks were reported, where the incriminated cause of the outbreak were milk or diary. In 126 (70.39%) outbreaks, totaling 2276 sick individuals and one casualty, it was confirmed that the incriminated food was from the group of dairy products. In 48 instances (26.82%), bacteriological tests confirmed that milk and dairy products were excluded as the outbreak causes, while in another 5 (2.79%) outbreaks, microbiological analysis of food failed to confirm any relation to the actual epidemiological instances. In some cases, bacteriological testing of incriminated foods was not possible. In the cases of outbreaks associated with the consumption of milk and dairy products, traditional raw milk products were cited as being used. Consumption of unpasteurized milk and cheese represents public health threat. National and international rules ensuring use of safe products for human consumption have to set rules of trade of thermally processed milk and products on the market.

The Hamburg Selection Procedure for Dental Students – Introduction of the HAM-Nat as subject-specific test for study aptitude

PubMed Central

Kothe, Christian; Hissbach, Johanna; Hampe, Wolfgang

2013-01-01

Introduction: The present study examines the question whether the selection of dental students should be based solely on average school-leaving grades (GPA) or whether it could be improved by using a subject-specific aptitude test. Methods: The HAM-Nat Natural Sciences Test was piloted with freshmen during their first study week in 2006 and 2007. In 2009 and 2010 it was used in the dental student selection process. The sample size in the regression models varies between 32 and 55 students. Results: Used as a supplement to the German GPA, the HAM-Nat test explained up to 12% of the variance in preclinical examination performance. We confirmed the prognostic validity of GPA reported in earlier studies in some, but not all of the individual preclinical examination results. Conclusion: The HAM-Nat test is a reliable selection tool for dental students. Use of the HAM-Nat yielded a significant improvement in prediction of preclinical academic success in dentistry. PMID:24282449

Occupational asthma induced by cephalosporins.

PubMed

Sastre, J; Quirce, S; Novalbos, A; Lluch-Bernal, M; Bombín, C; Umpiérrez, A

1999-05-01

A 20-yr-old pharmaceutical worker who developed attacks of shortness of breath and wheezing 9 months after beginning work on a process in which cefadroxil powder was bottled or encapsulated will be described. Skin test with cefaxodril was negative. Baseline spirometry and methacholine inhalation test were normal. A controlled bronchial challenge test was carried out in a closed-circuit system with assessment of respirable dust concentration. Exposure to cefadroxil powder at a mean concentration of 10 mg x m(-3) for 10 min elicited an isolated immediate asthmatic response, but no response was observed to control challenge with lactose. Single-blind oral challenge test with amoxicillin up to 500 mg was well tolerated, whereas the oral challenge with cephalexin (25 mg) elicited an immediate asthmatic response. This patient had developed occupational asthma caused by inhalation of cefadroxil as confirmed by specific inhalation test. Since she tolerated oral amoxicillin, a synthetic penicillin with the side-chain identical to that of cefadroxil, it seems that she may be sensitized to the dihydrothiazine ring of cephalosporins.

Spring 2013 Graduate Engineering Internship Summary

NASA Technical Reports Server (NTRS)

Ehrlich, Joshua

2013-01-01

In the spring of 2013, I participated in the National Aeronautics and Space Administration (NASA) Pathways Intern Employment Program at the Kennedy Space Center (KSC) in Florida. This was my final internship opportunity with NASA, a third consecutive extension from a summer 2012 internship. Since the start of my tenure here at KSC, I have gained an invaluable depth of engineering knowledge and extensive hands-on experience. These opportunities have granted me the ability to enhance my systems engineering approach in the field of payload design and testing as well as develop a strong foundation in the area of composite fabrication and testing for repair design on space vehicle structures. As a systems engineer, I supported the systems engineering and integration team with final acceptance testing of the Vegetable Production System, commonly referred to as Veggie. Verification and validation (V and V) of Veggie was carried out prior to qualification testing of the payload, which incorporated the process of confirming the system's design requirements dependent on one or more validation methods: inspection, analysis, demonstration, and testing.

[Usefulness of the fruit fly for assessment of mutagenicity of benzene, acetaldehyde and formaldehyde].

PubMed

Krogulski, A

1994-01-01

Among the contaminants of water, soil and air the number of mutagenic and carcinogenic substances is increasing. For the assessment of health risk connected with the simple and cheap methods are necessary which could detected and measure the mutagenicity of these substances. The widely used tests using prokaryotes give negative results in the tests of certain substances which are carcinogenic in mammals. In the case of benzene and acetaldehyde Ames test gives false negative results, and in the case of formaldehyde the results are equivocal. An advantage of fruit fly Drosophila melanogaster used for this purpose is that its cell structures, enzymes and metabolic processes are similar to those of mammals. For the demonstration of mutagenicity of benzene, acetaldehyde and formaldehyde the test of somatic mutation and recombination SMART was carried out in these flies. The results confirmed the usefulness of the SMART test for the demonstration of the mutagenicity of contaminants in the environment.

A short term quality control tool for biodegradable microspheres.

PubMed

D'Souza, Susan; Faraj, Jabar A; Dorati, Rossella; DeLuca, Patrick P

2014-06-01

Accelerated in vitro release testing methodology has been developed as an indicator of product performance to be used as a discriminatory quality control (QC) technique for the release of clinical and commercial batches of biodegradable microspheres. While product performance of biodegradable microspheres can be verified by in vivo and/or in vitro experiments, such evaluation can be particularly challenging because of slow polymer degradation, resulting in extended study times, labor, and expense. Three batches of Leuprolide poly(lactic-co-glycolic acid) (PLGA) microspheres having varying morphology (process variants having different particle size and specific surface area) were manufactured by the solvent extraction/evaporation technique. Tests involving in vitro release, polymer degradation and hydration of the microspheres were performed on the three batches at 55°C. In vitro peptide release at 55°C was analyzed using a previously derived modification of the Weibull function termed the modified Weibull equation (MWE). Experimental observations and data analysis confirm excellent reproducibility studies within and between batches of the microsphere formulations demonstrating the predictability of the accelerated experiments at 55°C. The accelerated test method was also successfully able to distinguish the in vitro product performance between the three batches having varying morphology (process variants), indicating that it is a suitable QC tool to discriminate product or process variants in clinical or commercial batches of microspheres. Additionally, data analysis utilized the MWE to further quantify the differences obtained from the accelerated in vitro product performance test between process variants, thereby enhancing the discriminatory power of the accelerated methodology at 55°C.

Dilution testing using rapid diagnostic tests in a HIV diagnostic algorithm: a novel alternative for confirmation testing in resource limited settings.

PubMed

Shanks, Leslie; Siddiqui, M Ruby; Abebe, Almaz; Piriou, Erwan; Pearce, Neil; Ariti, Cono; Masiga, Johnson; Muluneh, Libsework; Wazome, Joseph; Ritmeijer, Koert; Klarkowski, Derryck

2015-05-14

Current WHO testing guidelines for resource limited settings diagnose HIV on the basis of screening tests without a confirmation test due to cost constraints. This leads to a potential risk of false positive HIV diagnosis. In this paper, we evaluate the dilution test, a novel method for confirmation testing, which is simple, rapid, and low cost. The principle of the dilution test is to alter the sensitivity of a rapid diagnostic test (RDT) by dilution of the sample, in order to screen out the cross reacting antibodies responsible for falsely positive RDT results. Participants were recruited from two testing centres in Ethiopia where a tiebreaker algorithm using 3 different RDTs in series is used to diagnose HIV. All samples positive on the initial screening RDT and every 10th negative sample underwent testing with the gold standard and dilution test. Dilution testing was performed using Determine™ rapid diagnostic test at 6 different dilutions. Results were compared to the gold standard of Western Blot; where Western Blot was indeterminate, PCR testing determined the final result. 2895 samples were recruited to the study. 247 were positive for a prevalence of 8.5 % (247/2895). A total of 495 samples underwent dilution testing. The RDT diagnostic algorithm misclassified 18 samples as positive. Dilution at the level of 1/160 was able to correctly identify all these 18 false positives, but at a cost of a single false negative result (sensitivity 99.6 %, 95 % CI 97.8-100; specificity 100 %, 95 % CI: 98.5-100). Concordance between the gold standard and the 1/160 dilution strength was 99.8 %. This study provides proof of concept for a new, low cost method of confirming HIV diagnosis in resource-limited settings. It has potential for use as a supplementary test in a confirmatory algorithm, whereby double positive RDT results undergo dilution testing, with positive results confirming HIV infection. Negative results require nucleic acid testing to rule out false negative results due to seroconversion or misclassification by the lower sensitivity dilution test. Further research is needed to determine if these results can be replicated in other settings. ClinicalTrials.gov, NCT01716299 .

The effects of valence and arousal on the neural activity leading to subsequent memory.

PubMed

Mickley Steinmetz, Katherine R; Kensinger, Elizabeth A

2009-11-01

This study examined how valence and arousal affect the processes linked to subsequent memory for emotional information. While undergoing an fMRI scan, participants viewed neutral pictures and emotional pictures varying by valence and arousal. After the scan, participants performed a recognition test. Subsequent memory for negative or high arousal information was associated with occipital and temporal activity, whereas memory for positive or low arousal information was associated with frontal activity. Regression analyses confirmed that for negative or high arousal items, temporal lobe activity was the strongest predictor of later memory whereas for positive or low arousal items, frontal activity corresponded most strongly with later memory. These results suggest that the types of encoding processes relating to memory (e.g., sensory vs. elaborative processing) can differ based on the affective qualities of emotional information.

The effects of valence and arousal on the neural activity leading to subsequent memory

PubMed Central

Mickley Steinmetz, Katherine R.; Kensinger, Elizabeth A.

2010-01-01

This study examined how valence and arousal affect the processes linked to subsequent memory for emotional information. While undergoing an fMRI scan, participants viewed neutral pictures and emotional pictures varying by valence and arousal. After the scan, participants performed a recognition test. Subsequent memory for negative or high arousal information was associated with occipital and temporal activity, while memory for positive or low arousal information was associated with frontal activity. Regression analyses confirmed that for negative or high arousal items, temporal lobe activity was the strongest predictor of later memory whereas for positive or low arousal items, frontal activity corresponded most strongly with later memory. These results suggest that the types of encoding processes relating to memory (e.g., sensory vs. elaborative processing) can differ based on the affective qualities of emotional information. PMID:19674398

The influence of schizotypal traits on attention under high perceptual load.

PubMed

Stotesbury, Hanne; Gaigg, Sebastian B; Kirhan, Saim; Haenschel, Corinna

2018-03-01

Schizophrenia Spectrum Disorders (SSD) are known to be characterised by abnormalities in attentional processes, but there are inconsistencies in the literature that remain unresolved. This article considers whether perceptual resource limitations play a role in moderating attentional abnormalities in SSD. According to perceptual load theory, perceptual resource limitations can lead to attenuated or superior performance on dual-task paradigms depending on whether participants are required to process, or attempt to ignore, secondary stimuli. If SSD is associated with perceptual resource limitations, and if it represents the extreme end of an otherwise normally distributed neuropsychological phenotype, schizotypal traits in the general population should lead to disproportionate performance costs on dual-task paradigms as a function of the perceptual task demands. To test this prediction, schizotypal traits were quantified via the Schizotypal Personality Questionnaire (SPQ) in 74 healthy volunteers, who also completed a dual-task signal detection paradigm that required participants to detect central and peripheral stimuli across conditions that varied in the overall number of stimuli presented. The results confirmed decreasing performance as the perceptual load of the task increased. More importantly, significant correlations between SPQ scores and task performance confirmed that increased schizotypal traits, particularly in the cognitive-perceptual domain, are associated with greater performance decrements under increasing perceptual load. These results confirm that attentional difficulties associated with SSD extend sub-clinically into the general population and suggest that cognitive-perceptual schizotypal traits may represent a risk factor for difficulties in the regulation of attention under increasing perceptual load.

3-(Bromomethyl)-2-chloro-4-(methylsulfonyl)- benzoic acid: a new cause of sensitiser induced occupational asthma, rhinitis and urticaria.

PubMed

Suojalehto, Hille; Karvala, Kirsi; Ahonen, Saana; Ylinen, Katriina; Airaksinen, Liisa; Suuronen, Katri; Suomela, Sari; Lindström, Irmeli

2018-04-01

3-(Bromomethyl)-2-chloro-4-(methylsulfonyl)-benzoic acid (BCMBA) has not previously been identified as a respiratory sensitiser. We detected two cases who presented respiratory and urticaria symptoms related to BCMBA and had positive skin prick tests to the agent. Subsequently, we conducted outbreak investigations at the BCMBA-producing factory and performed clinical examinations to confirm occupational diseases. The outbreak investigations included observations of work processes, assessment of exposure, a medical survey with a questionnaire and skin prick tests with 0.5% BCMBA water solution on 85 exposed workers and 9 unexposed workers. We used specific inhalation or nasal challenge and open skin application test to investigate BCMBA-related occupational asthma, rhinitis and contact urticaria. We identified nine workers with respiratory and/or skin symptoms and positive skin prick tests to BCMBA in a chemical factory. A survey among chemical factory workers indicated a BCMBA-related sensitisation rate of 8% among all exposed workers; the rate was highest (25%) among production workers in the production hall. Sensitisation was detected only in workers with the estimated highest exposure levels. Six cases of occupational asthma, rhinitis and/or contact urticaria caused by BCMBA were confirmed with challenge tests. Asthma-provoking doses in specific inhalation challenges were very low (0.03% or 0.3% BCMBA in lactose). We identified a new low molecular weight agent causing occupational asthma, rhinitis and contact urticaria. A typical clinical picture of allergic diseases and positive skin prick tests suggest underlying IgE-mediated disease mechanisms. Stringent exposure control measures are needed in order to prevent BCMBA-related diseases. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Optimization and stabilization of gold nanoparticles by using herbal plant extract with microwave heating

NASA Astrophysics Data System (ADS)

Yasmin, Akbar; Ramesh, Kumaraswamy; Rajeshkumar, Shanmugam

2014-04-01

In this study, we have synthesized the gold nanoparticles by using Hibiscus rosa-sinensis, a medicinal plant. The gold nanoparticles were synthesized rapidly by the involvement of microwave heating. By changing of plant extract concentration, gold solution concentration, microwave heating time and power of microwave heating the optimized condition was identified. The surface Plasmon resonance found at 520 nm confirmed the gold nanoparticles synthesis. The spherical sized nanoparticles in the size range of 16-30 nm were confirmed by Transmission Electron Microscope (TEM). The stability of the nanoparticles is very well proved in the invitro stability tests. The biochemical like alkaloids and flavonoids play a vital role in the nanoparticles synthesis was identified using the Fourier Transform Infrared Spectroscopy (FTIR). Combining the phytochemical and microwave heating, the rapid synthesis of gold nanoparticles is the novel process for the medically applicable gold nanoparticles production.

Analysis of Square Cup Deep-Drawing Test of Pure Titanium

NASA Astrophysics Data System (ADS)

Ogawa, Takaki; Ma, Ninshu; Ueyama, Minoru; Harada, Yasunori

2016-08-01

The prediction of formability of titunium is more difficult than steels since its strong anisotropy. If computer simulation can estimate the formability of titanium, we can select the optimal forming conditions. The purpose of this study was to acquire knowledge for the formability prediction by the computer simulation of the square cup deep-drawing of pure titanium. In this paper, the results of FEM analsis of pure titanium were compared with the experimental results to examine the analysis validity. We analyzed the formability of deepdrawing square cup of titanium by the FEM using solid elements. Compared the analysis results with the experimental results such as the forming shape, the punch load, and the thickness, the validity was confirmed. Further, through analyzing the change of the thickness around the forming corner, it was confirmed that the thickness increased to its maximum value during forming process at the stroke of 35mm more than the maximum stroke.

Exploring Selective Exposure and Confirmation Bias as Processes Underlying Employee Work Happiness: An Intervention Study.

PubMed

Williams, Paige; Kern, Margaret L; Waters, Lea

2016-01-01

Employee psychological capital (PsyCap), perceptions of organizational virtue (OV), and work happiness have been shown to be associated within and over time. This study examines selective exposure and confirmation bias as potential processes underlying PsyCap, OV, and work happiness associations. As part of a quasi-experimental study design, school staff (N = 69) completed surveys at three time points. After the first assessment, some staff (n = 51) completed a positive psychology training intervention. Results of descriptive statistics, correlation, and regression analyses on the intervention group provide some support for selective exposure and confirmation bias as explanatory mechanisms. In focusing on the processes through which employee attitudes may influence work happiness this study advances theoretical understanding, specifically of selective exposure and confirmation bias in a field study context.

Laser fabrication of Ag-HA nanocomposites on Ti6Al4V implant for enhancing bioactivity and antibacterial capability.

PubMed

Liu, Xiangmei; Man, H C

2017-01-01

For titanium alloy implants, both surface bioactivity and antibacterial infection are the two critical factors in determining the success of clinical implantation of these metallic implants. In the present work, a novel nanocomposite layer of nano-silver-containing hydroxyapatite (Ag-HA) was prepared on the surface of biomedical Ti6Al4V by laser processing. Analysis using SEM, EDS and XRD shows the formation of an Ag-HA layer of about 200μm fusion bonded to the substrate. Mineralization tests in simulated body fluid (SBF) showed that laser fabricated Ag-HA nanocomposite layer favors the deposition of apatite on the surface of the implants. Antibacterial tests confirmed that all Ag-HA nanocomposite layers can kill bacteria while a higher Ag content would lower the cytocompatibility of these coatings. Cell viability decreases when the Ag content reaches 5% in these coatings, due to the larger amount of Ag leached out, as confirmed by ion release evaluation. Our results reveal that laser fabricated Ag-HA nanocomposite coatings containing 2% Ag show both excellent cytocompatibility and antibacterial capability. Copyright © 2016 Elsevier B.V. All rights reserved.

Thermograpic study of upper extremities in patients with cerebral palsy

NASA Astrophysics Data System (ADS)

Lampe, R.; Kawelke, S.; Mitternacht, J.; Turova, V.; Blumenstein, T.; Alves-Pinto, A.

2015-03-01

Trophic disorders like reduced skin blood circulation are well-known epiphenomenon of cerebral palsy (CP). They can influence quality of life and can lead to skin damages and, as a consequence, to decubitus. Therefore, it is important to analyse temperature regulation in patients with CP. Thermal imaging camera FLIR BCAM SD was used to study the dependency of skin blood circulation in upper extremities of patients with CP on hand dominance, hand force and hand volume. The hand force was evaluated using a conventional dynamometer. The hand volume was measured with a volumeter. A cold stress test for hands was applied in 22 patients with CP and 6 healthy subjects. The warming up process after the test was recorded with the thermal camera. It was confirmed that the hands of patients warm up slower comparing to healthy persons. The patients' working hands warm up faster than non-working ones. A slight correlation was established between the hand grip force of the working hands and their warm up time. No correlation was found between the warming up time and the volume of the hand. The results confirm our assumption that there is a connection of peripheral blood circulation to upper limb motor functions.

Different slopes of a mountain can determine the structure of ferns and lycophytes communities in a tropical forest of Brazil.

PubMed

Nettesheim, Felipe C; Damasceno, Elaine R; Sylvestre, Lana S

2014-03-01

A community of Ferns and Lycophytes was investigated by comparing the occurrence of species on different slopes of a paleoisland in Southeastern Brazil. Our goal was to evaluate the hypothesis that slopes with different geographic orientations determine a differentiation of Atlantic Forest ferns and lycophytes community. We recorded these plants at slopes turned towards the continent and at slopes turned towards the open sea. Analysis consisted of a preliminary assessment on fern beta diversity, a Non Metric Multidimensional Scaling (NMDS) and a Student t-test to confirm if sites sampling units ordination was different at each axis. We further used the Pearson coefficient to relate fern species to the differentiation pattern and again Student's t-test to determine if richness, plant cover and abundance varied between the two sites. There was a relatively low number of shared species between the two sites and ferns and lycophytes community variation was confirmed. Some species were detected as indicators of the community variation but we were unable to detect richness, plant cover or abundance differences. Despite the evidence of this variation between the slopes, further works are needed to evaluate which processes are contributing to determine this pattern.

Cross-script and within-script priming in alcoholic Korsakoff patients.

PubMed

Komatsu, Shin-Ichi; Mimura, Masaru; Kato, Motoichiro; Kashima, Haruo

2003-04-01

In two experiments, alcoholic Korsakoff patients and control subjects studied a list of Japanese nouns written in either Hiragana or Kanji script. Word-fragment completion and recognition tests were then administered in Hiragana. When the writing script was changed between study and test phases, repetition priming in word-fragment completion was significantly attenuated but was still reliable against baseline performance. This was confirmed for both Korsakoff patients and control subjects. In contrast, the script change had little effect on recognition memory, which was severely impaired in Korsakoff patients. The results suggest that repetition priming is mediated by two different implicit processes, one that is script-specific and the other that is assumed to operate at a more abstract level.

Investigation of nitrogen transport in active screen plasma nitriding processes - Uphill diffusion effect

NASA Astrophysics Data System (ADS)

Jasinski, J. J.; Fraczek, T.; Kurpaska, L.; Lubas, M.; Sitarz, M.

2018-07-01

The paper presents a structure of a nitrided layer formed with active screen plasma nitriding (ASPN) technique, which is a modification of plasma nitriding. The model investigated material was Fe Armco. The nitriding processes were carried out at 773 K for 6 h and 150 Pa. The main objective of this study was to confirm nitrogen migration effect and its influence on the nitride layer formation in different area of the layer interfaces (ε/ε+γ‧/γ‧). The results of the tests were evaluated using scanning electron microscopy (SEM, SEM/EBSD), transmission electron microscopy - electron energy loss spectroscopy (TEM-EFTEM), secondary ion mass spectroscopy (SIMS) and Wavelength Dispersive X-Ray Spectrometry (WDS). The analysis of the results suggests that the structures of the nitrided layers and nitrides morphology differ for various parameters and are dependent on the surface layer saturation mechanism for each of the temperatures and process parameters. New approaches in diffusion of nitrogen and carbon atoms and optimizing process were also analyzed. Nitrogen and also carbon transport in the sublayer was observed by several effects i.e. uphill diffusion effect which confirmed migration of the atoms in diffusive layer towards top surface (ε/ε+γ‧ interface) and stress change effect in the nitrogen saturation area of the (Fe(C,N)+γ‧) layer. Results showed in the paper might be used both for optimization of ASPN processes, modeling of nitrided layers formation mechanism and for controlling the nitrided layers morphology when nitriding different Fe based materials.

Physicochemical properties of film-coated melt-extruded pellets.

PubMed

Young, Chistopher R; Crowley, Michael; Dietzsch, Caroline; McGinity, James W

2007-02-01

The purpose of this study was to investigate the physicochemical properties of poly(ethylene oxide) (PEO) and guaifenesin containing beads prepared by a melt-extrusion process and film-coated with a methacrylic acid copolymer. Solubility parameter calculations, thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), modulated differential scanning calorimetry (MDSC), X-ray powder diffraction (XRPD) and high performance liquid chromatography (HPLC) were used to determine drug/polymer miscibility and/or the thermal processibility of the systems. Powder blends of guaifenesin, PEO and functional excipients were processed using a melt-extrusion and spheronization technique and then film-coated in a fluidized bed apparatus. Solubility parameter calculations were used to predict miscibility between PEO and guaifenesin, and miscibility was confirmed by SEM and observation of a single melting point for extruded drug/polymer blends during MDSC investigations. The drug was stable following melt-extrusion as determined by TGA and HPLC; however, drug release rate from pellets decreased upon storage in sealed HDPE containers with silica desiccants at 40 degrees C/75% RH. The weight loss on drying, porosity and tortuosity determinations were not influenced by storage. Recrystallization of guaifenesin and PEO was confirmed by SEM and XRPD. Additionally, the pellets exhibited a change in adhesion behaviour during dissolution testing. The addition of ethylcellulose to the extruded powder blend decreased and stabilized the drug release rate from the thermally processed pellets. The current study also demonstrated film-coating to be an efficient process for providing melt-extruded beads with pH-dependent drug release properties that were stable upon storage at accelerated conditions.

Bench-scale research in biomass liquefaction in support of the Albany, Oregon experimental facility

NASA Astrophysics Data System (ADS)

Elliott, D. C.

1981-03-01

The liquefaction of solid materials (wood, newsprint, animal manure) by beating to produce useful liquid fuels was investigated. Highlights of work performed include: (1) catalyst mechanism studies; (2) analytical reports on TR8 and TR9 product oils; (3) liquid chromatography/mass spectroscopy analysis of wood oil; (4) batch conversion tests on bottom material; (5) vapor pressure studies; and (6) product evaluation. It was confirmed that the key process parameters and the effects of varying operating conditions are in support of biomass liquefaction.

Education technology with continuous real time monitoring of the current functional and emotional students' states

NASA Astrophysics Data System (ADS)

Alyushin, M. V.; Kolobashkina, L. V.

2017-01-01

The education technology with continuous monitoring of the current functional and emotional students' states is suggested. The application of this technology allows one to increase the effectiveness of practice through informed planning of the training load. For monitoring the current functional and emotional students' states non-contact remote technologies of person bioparameters registration are encouraged to use. These technologies are based on recording and processing in real time the main person bioparameters in a purely passive mode. Experimental testing of this technology has confirmed its effectiveness.

The transfer of technology to measure skin burn depth in humans

NASA Technical Reports Server (NTRS)

Yost, William T.; Cantrell, John H.

1991-01-01

Discussed here is the use of ultrasonic techniques originally used to locate cracks in metal structues to measure burn wound depth in humans. Acoustic impedance, performance tests, and the theoretical model are discussed. Measurements of skin burns on anesthetized pigs made with the the ultrasonic instrumentation were in agreement with diagnoses made by a physician, and subsequently confirmed by the healing process. Researchers felt that the concept proved useful in a clinical setting and that the instrument and concept were ready to extend to the manufacturer.

The role of retrieval mode and retrieval orientation in retrieval practice: insights from comparing recognition memory testing formats and restudying.

PubMed

Gao, Chuanji; Rosburg, Timm; Hou, Mingzhu; Li, Bingbing; Xiao, Xin; Guo, Chunyan

2016-12-01

The effectiveness of retrieval practice for aiding long-term memory, referred to as the testing effect, has been widely demonstrated. However, the specific neurocognitive mechanisms underlying this phenomenon remain unclear. In the present study, we sought to explore the role of pre-retrieval processes at initial testing on later recognition performance by using event-related potentials (ERPs). Subjects studied two lists of words (Chinese characters) and then performed a recognition task or a source memory task, or restudied the word lists. At the end of the experiment, subjects received a final recognition test based on the remember-know paradigm. Behaviorally, initial testing (active retrieval) enhanced memory retention relative to restudying (passive retrieval). The retrieval mode at initial testing was indexed by more positive-going ERPs for unstudied items in the active-retrieval tasks than in passive retrieval from 300 to 900 ms. Follow-up analyses showed that the magnitude of the early ERP retrieval mode effect (300-500 ms) was predictive of the behavioral testing effect later on. In addition, the ERPs for correctly rejected new items during initial testing differed between the two active-retrieval tasks from 500 to 900 ms, and this ERP retrieval orientation effect predicted differential behavioral testing gains between the two active-retrieval conditions. Our findings confirm that initial testing promotes later retrieval relative to restudying, and they further suggest that adopting pre-retrieval processing in the forms of retrieval mode and retrieval orientation might contribute to these memory enhancements.

A Flight Test of the Strapdown Airborne Gravimeter SGA-WZ in Greenland

PubMed Central

Zhao, Lei; Forsberg, René; Wu, Meiping; Olesen, Arne Vestergaard; Zhang, Kaidong; Cao, Juliang

2015-01-01

An airborne gravimeter is one of the most important tools for gravity data collection over large areas with mGal accuracy and a spatial resolution of several kilometers. In August 2012, a flight test was carried out to determine the feasibility and to assess the accuracy of the new Chinese SGA-WZ strapdown airborne gravimeter in Greenland, in an area with good gravity coverage from earlier marine and airborne surveys. An overview of this new system SGA-WZ is given, including system design, sensor performance and data processing. The processing of the SGA-WZ includes a 160 s length finite impulse response filter, corresponding to a spatial resolution of 6 km. For the primary repeated line, a mean r.m.s. deviation of the differences was less than 1.5 mGal, with the error estimate confirmed from ground truth data. This implies that the SGA-WZ could meet standard geophysical survey requirements at the 1 mGal level. PMID:26057039

The Effect of Constant and Pulsed Current Gas Tungsten Arc Welding on Joint Properties of 2205 Duplex Stainless Steel to 316L Austenitic Stainless Steel

NASA Astrophysics Data System (ADS)

Neissi, R.; Shamanian, M.; Hajihashemi, M.

2016-05-01

In this study, dissimilar 316L austenitic stainless steel/2205 duplex stainless steel (DSS) joints were fabricated by constant and pulsed current gas tungsten arc welding process using ER2209 DSS as a filler metal. Microstructures and joint properties were characterized using optical and electron scanning microscopy, tensile, Charpy V-notch impact and micro-hardness tests, and cyclic polarization measurements. Microstructural observations confirmed the presence of chromium nitride and delta ferrite in the heat-affected zone of DSS and 316L, respectively. In addition, there was some deviation in the austenite/ferrite ratio of the surface welding pass in comparison to the root welding pass. Besides having lower pitting potential, welded joints produced by constant current gas tungsten arc welding process, consisted of some brittle sigma phase precipitates, which resulted in some impact energy reduction. The tensile tests showed high tensile strength for the weld joints in which all the specimens were broken in 316L base metal.

New procyanidin B3-human salivary protein complexes by mass spectrometry. Effect of salivary protein profile, tannin concentration, and time stability.

PubMed

Perez-Gregorio, Maria Rosa; Mateus, Nuno; De Freitas, Victor

2014-10-15

Several factors could influence the tannin-protein interaction such as the human salivary protein profile, the tannin tested, and the tannin/protein ratio. The goal of this study aims to study the effect of different salivas (A, B, and C) and different tannin concentrations (0.5 and 1 mg/mL) on the interaction process as well as the complex's stability over time. This study is focused on the identification of new procyanidin B3-human salivary protein complexes. Thus, 48 major B3-human salivary protein aggregates were identified regardless of the saliva and tannin concentration tested. A higher number of aggregates was found at lower tannin concentration. Moreover, the number of protein moieties involved in the aggregation process was higher when the tannin concentration was also higher. The selectivity of the different groups of proteins to bind tannin was also confirmed. It was also verified that the B3-human salivary protein complexes formed evolved over time.

Cognitive Bias in Systems Verification

NASA Technical Reports Server (NTRS)

Larson, Steve

2012-01-01

Working definition of cognitive bias: Patterns by which information is sought and interpreted that can lead to systematic errors in decisions. Cognitive bias is used in diverse fields: Economics, Politics, Intelligence, Marketing, to name a few. Attempts to ground cognitive science in physical characteristics of the cognitive apparatus exceed our knowledge. Studies based on correlations; strict cause and effect is difficult to pinpoint. Effects cited in the paper and discussed here have been replicated many times over, and appear sound. Many biases have been described, but it is still unclear whether they are all distinct. There may only be a handful of fundamental biases, which manifest in various ways. Bias can effect system verification in many ways . Overconfidence -> Questionable decisions to deploy. Availability -> Inability to conceive critical tests. Representativeness -> Overinterpretation of results. Positive Test Strategies -> Confirmation bias. Debiasing at individual level very difficult. The potential effect of bias on the verification process can be managed, but not eliminated. Worth considering at key points in the process.

Separation of actinides from irradiated An-Zr based fuel by electrorefining on solid aluminium cathodes in molten LiCl-KCl

NASA Astrophysics Data System (ADS)

Souček, P.; Murakami, T.; Claux, B.; Meier, R.; Malmbeck, R.; Tsukada, T.; Glatz, J.-P.

2015-04-01

An electrorefining process for metallic spent nuclear fuel treatment is being investigated in ITU. Solid aluminium cathodes are used for homogeneous recovery of all actinides within the process carried out in molten LiCl-KCl eutectic salt at a temperature of 500 °C. As the selectivity, efficiency and performance of solid Al has been already shown using un-irradiated An-Zr alloy based test fuels, the present work was focused on laboratory-scale demonstration of the process using irradiated METAPHIX-1 fuel composed of U67-Pu19-Zr10-MA2-RE2 (wt.%, MA = Np, Am, Cm, RE = Nd, Ce, Gd, Y). Different electrorefining techniques, conditions and cathode geometries were used during the experiment yielding evaluation of separation factors, kinetic parameters of actinide-aluminium alloy formation, process efficiency and macro-structure characterisation of the deposits. The results confirmed an excellent separation and very high efficiency of the electrorefining process using solid Al cathodes.

Syntactic and semantic restrictions on morphological recomposition: MEG evidence from Greek.

PubMed

Neophytou, K; Manouilidou, C; Stockall, L; Marantz, A

2018-05-16

Complex morphological processing has been extensively studied in the past decades. However, most of this work has either focused on only certain steps involved in this process, or it has been conducted on a few languages, like English. The purpose of the present study is to investigate the spatiotemporal cortical processing profile of the distinct steps previously reported in the literature, from decomposition to re-composition of morphologically complex items, in a relatively understudied language, Greek. Using magnetoencephalography, we confirm the role of the fusiform gyrus in early, form-based morphological decomposition, we relate the syntactic licensing of stem-suffix combinations to the ventral visual processing stream, somewhat independent from lexical access for the stem, and we further elucidate the role of orbitofrontal regions in semantic composition. Thus, the current study offers the most comprehensive test to date of visual morphological processing and additional, crosslinguistic validation of the steps involved in it. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Optimization of Gas Metal Arc Welding Process Parameters

NASA Astrophysics Data System (ADS)

Kumar, Amit; Khurana, M. K.; Yadav, Pradeep K.

2016-09-01

This study presents the application of Taguchi method combined with grey relational analysis to optimize the process parameters of gas metal arc welding (GMAW) of AISI 1020 carbon steels for multiple quality characteristics (bead width, bead height, weld penetration and heat affected zone). An orthogonal array of L9 has been implemented to fabrication of joints. The experiments have been conducted according to the combination of voltage (V), current (A) and welding speed (Ws). The results revealed that the welding speed is most significant process parameter. By analyzing the grey relational grades, optimal parameters are obtained and significant factors are known using ANOVA analysis. The welding parameters such as speed, welding current and voltage have been optimized for material AISI 1020 using GMAW process. To fortify the robustness of experimental design, a confirmation test was performed at selected optimal process parameter setting. Observations from this method may be useful for automotive sub-assemblies, shipbuilding and vessel fabricators and operators to obtain optimal welding conditions.

Two-phase anaerobic digestion within a solid waste/wastewater integrated management system

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Gioannis, G.; Diaz, L.F.; Muntoni, A.

2008-07-01

A two-phase, wet anaerobic digestion process was tested at laboratory scale using mechanically pre-treated municipal solid waste (MSW) as the substrate. The proposed process scheme differs from others due to the integration of the MSW and wastewater treatment cycles, which makes it possible to avoid the recirculation of process effluent. The results obtained show that the supplying of facultative biomass, drawn from the wastewater aeration tank, to the solid waste acidogenic reactor allows an improvement of the performance of the first phase of the process which is positively reflected on the second one. The proposed process performed successfully, adopting mesophilicmore » conditions and a relatively short hydraulic retention time in the methanogenic reactor, as well as high values of organic loading rate. Significant VS removal efficiency and biogas production were achieved. Moreover, the methanogenic reactor quickly reached optimal conditions for a stable methanogenic phase. Studies conducted elsewhere also confirm the feasibility of integrating the treatment of the organic fraction of MSW with that of wastewater.« less

A novel method about detecting missing holes on the motor carling

NASA Astrophysics Data System (ADS)

Xu, Hongsheng; Tan, Hao; Li, Guirong

2018-03-01

After a deep analysis on how to use an image processing system to detect the missing holes on the motor carling, we design the whole system combined with the actual production conditions of the motor carling. Afterwards we explain the whole system's hardware and software in detail. We introduce the general functions for the system's hardware and software. Analyzed these general functions, we discuss the modules of the system's hardware and software and the theory to design these modules in detail. The measurement to confirm the area to image processing, edge detection, randomized Hough transform to circle detecting is explained in detail. Finally, the system result tested in the laboratory and in the factory is given out.

Inverted bulk-heterojunction solar cell with cross-linked hole-blocking layer

PubMed Central

Udum, Yasemin; Denk, Patrick; Adam, Getachew; Apaydin, Dogukan H.; Nevosad, Andreas; Teichert, Christian; S. White, Matthew.; S. Sariciftci, Niyazi.; Scharber, Markus C.

2014-01-01

We have developed a hole-blocking layer for bulk-heterojunction solar cells based on cross-linked polyethylenimine (PEI). We tested five different ether-based cross-linkers and found that all of them give comparable solar cell efficiencies. The initial idea that a cross-linked layer is more solvent resistant compared to a pristine PEI layer could not be confirmed. With and without cross-linking, the PEI layer sticks very well to the surface of the indium–tin–oxide electrode and cannot be removed by solvents used to process PEI or common organic semiconductors. The cross-linked PEI hole-blocking layer functions for multiple donor–acceptor blends. We found that using cross-linkers improves the reproducibility of the device fabrication process. PMID:24817837

What to do after nutrient removal?

PubMed

van der Graaf, J H

2001-01-01

In the Netherlands, interest in advanced treatment is increasing now that almost all wastewater treatment plants apply full biological treatment and nutrient removal. The resulting effluents have an excellent quality which can be improved further by applying advanced treatment processes like flocculating filtration, membrane filtration, UV or activated carbon, and others. The treated effluent can be re-used for various purposes, as process water, household water, urban water, for groundwater suppletion and drinking water. Nowadays many applications are investigated. In order to confirm the applicability pilot test investigations are done at various WWTPs. The results are promising; the cost estimations show increasing prospects. This will finally lead to the maturity of the advanced treatment. It will certainly contribute to a more sustainable water cycle.

Processing and characterization of unidirectional thermoplastic nanocomposites

NASA Astrophysics Data System (ADS)

Narasimhan, Kameshwaran

The manufacture of continuous fibre-reinforced thermoplastic nanocomposites is discussed for the case of E-Glass reinforced polypropylene (PP) matrix and for E-Glass reinforced Polyamide-6 (Nylon-6), with and without dispersed nanoclay (montmorillonite) platelets. The E-Glass/PP nanocomposite was manufactured using pultrusion, whereas the E-Glass/Nylon-6 nanocomposite was manufactured using compression molding. Mechanical characterization of nanocomposites were performed and compared with traditional microcomposites. Compressive as well as shear strength of nanocomposites was improved by improving the yield strength of the surrounding matrix through the dispersion of nanoclay. Significant improvements were achieved in compressive strength and shear strength with relatively low nanoclay loadings. Initially, polypropylene with and without nanoclay were melt intercalated using a single-screw extruder and the pultruded nanocomposite was fabricated using extruded pre-impregnated (pre-preg) tapes. Compression tests were performed as mandated by ASTM guidelines. SEM and TEM characterization revealed presence of nanoclay in an intercalated and partially exfoliated morphology. Mechanical tests confirmed significant improvements in compressive strength (˜122% at 10% nanoclay loading) and shear strength (˜60% at 3% nanoclay loading) in modified pultruded E-Glass/PP nanocomposites in comparison with baseline properties. Uniaxial tensile tests showed a small increase in tensile strength (˜3.4%) with 3% nanoclay loading. Subsequently, E-Glass/Nylon-6 nanocomposite panels were manufactured by compression molding. Compression tests were performed according to IITRI guidelines, whereas short beam shear and uni-axial tensile tests were performed according to ASTM standards. Mechanical tests confirmed strength enhancement with nanoclay addition, with a significant improvement in compressive strength (50% at 4% nanoclay loading) and shear strength (˜36% at 4% nanoclay loading) when compared with the baseline E-Glass/Nylon-6. Uni-axial tensile tests resulted in a small increase in tensile strength (˜3.2%) with 4% nanoclay loading. Also, hygrothermal aging (50°C and 100% RH) of baseline and nanoclay modified (4%) E-Glass/Nylon-6 was studied. It was observed that the moisture diffusion process followed Fickian diffusion. E-Glass/Nylon-6 modified with 4% nanoclay loading showed improved barrier performance with a significant reduction (˜30%) in moisture uptake compared to baseline E-Glass/Nylon-6 composites. Significant improvement in mechanical properties was also observed in hygrothermally aged nanocomposite specimens when compared with the aged baseline composite.

Using cognitive pre-testing methods in the development of a new evidenced-based pressure ulcer risk assessment instrument.

PubMed

Coleman, S; Nixon, J; Keen, J; Muir, D; Wilson, L; McGinnis, E; Stubbs, N; Dealey, C; Nelson, E A

2016-11-16

Variation in development methods of Pressure Ulcer Risk Assessment Instruments has led to inconsistent inclusion of risk factors and concerns about content validity. A new evidenced-based Risk Assessment Instrument, the Pressure Ulcer Risk Primary Or Secondary Evaluation Tool - PURPOSE-T was developed as part of a National Institute for Health Research (NIHR) funded Pressure Ulcer Research Programme (PURPOSE: RP-PG-0407-10056). This paper reports the pre-test phase to assess and improve PURPOSE-T acceptability, usability and confirm content validity. A descriptive study incorporating cognitive pre-testing methods and integration of service user views was undertaken over 3 cycles comprising PURPOSE-T training, a focus group and one-to-one think-aloud interviews. Clinical nurses from 2 acute and 2 community NHS Trusts, were grouped according to job role. Focus group participants used 3 vignettes to complete PURPOSE-T assessments and then participated in the focus group. Think-aloud participants were interviewed during their completion of PURPOSE-T. After each pre-test cycle analysis was undertaken and adjustment/improvements made to PURPOSE-T in an iterative process. This incorporated the use of descriptive statistics for data completeness and decision rule compliance and directed content analysis for interview and focus group data. Data were collected April 2012-June 2012. Thirty-four nurses participated in 3 pre-test cycles. Data from 3 focus groups, 12 think-aloud interviews incorporating 101 PURPOSE-T assessments led to changes to improve instrument content and design, flow and format, decision support and item-specific wording. Acceptability and usability were demonstrated by improved data completion and appropriate risk pathway allocation. The pre-test also confirmed content validity with clinical nurses. The pre-test was an important step in the development of the preliminary PURPOSE-T and the methods used may have wider instrument development application. PURPOSE-T proposes a new approach to pressure ulcer risk assessment, incorporating a screening stage, the inclusion of skin status to distinguish between those who require primary prevention and those who require secondary prevention/treatment and the use of colour to support pathway allocation and decision making. Further clinical evaluation is planned to assess the reliability and validity of PURPOSE-T and it's impact on care processes and patient outcomes.

[EC5-Space Suit Assembly Team- Internship

NASA Technical Reports Server (NTRS)

Maicke, Andrew

2016-01-01

There were three main projects in this internship. The first pertained to the Bearing Dust Cycle Test, in particular automating the test to allow for easier administration. The second concerned modifying the communication system setup in the Z2 suit, where speakers and mics were adjusted to allow for more space in the helmet. And finally, the last project concerned the tensile strength testing of fabrics deemed as candidates for space suit materials and desired to be sent off for radiation testing. The major duties here are split up between the major projects detailed above. For the Bearing Dust Cycle Test, the first objective was to find a way to automate administration of the test, as the previous version was long and tedious to perform. In order to do this, it was necessary to introduce additional electronics and perform programming to control the automation. Once this was done, it would be necessary to update documents concerning the test setup, procedure, and potential hazards. Finally, I was tasked with running tests using the new system to confirm system performance. For the Z2 communication system modifications, it was necessary to investigate alternative speakers and microphones which may have better performance than those currently used in the suit. Further, new speaker and microphone positions needed to be identified to keep them out of the way of the suit user. Once this was done, appropriate hardware (such as speaker or microphone cases and holders) could be prototyped and fabricated. For the suit material strength testing, the first task was to gather and document various test fabrics to identify the best suit material candidates. Then, it was needed to prepare samples for testing to establish baseline measurements and specify a testing procedure. Once the data was fully collected, additional test samples would be prepared and sent off-site to undergo irradiation before being tested again to observe changes in strength performance. For the Bearing Dust Cycle Test, automation was achieved through use of a servo motor and code written in LabVIEW. With this a small electrical servo controller was constructed and added to the system. For the Z2 communication modifications speaker cases were developed and printed, and new speakers and mics were selected. This allowed us to move the speakers and mics to locations to remain out of the suit users way. For the suit material strength testing, five material candidates were identified and test samples were created. These samples underwent testing, and baseline test results were gathered, though these results are currently being investigated for accuracy. The main process efficiency developed during the course of this internship comes from automation of the Bearing Dust Cycle Test. In particular, many hours of human involvement and precise operation are replaced with a simple motor setup. Thus it is no longer required to man the test, saving valuable employee time. This internship has confirmed a few things for me, namely that I both want to work as an engineer for an aerospace firm and that in particular I want to work for the Johnson Space Center. I am also confirmed in my desire to work with electronics, though I was surprised to enjoy prototyping 3D CAD design as much as I did. Therefore, I will make an effort to build my skills in this area so that I can continue to design mechanical models. In fact, I found the process of hands-on prototyping to be perhaps the most fun aspect of my time working here. This internship has also furthered my excitement for continual education, and I will hopefully be pursuing a masters in my field in the near future.

Biotechnology Conference: Diagnostics 󈨛 Held in Cambridge, England on 10 and 11 December 1987.

DTIC Science & Technology

1988-05-25

settings. 1 -hour culture confirmation test for herpes (ColorGene DNA hybridization test for HSV confirmation). This test NEW AMPEROMETRIC BIOSENSORS...I Thin Layer Technology: Monolayers to Multi Thin Films ................. 1 Single-Step Immunoassay Systems...if this thin-layer pr•ccss~is probe technolh,,y. and biosensors. The aim of the con- demonstrated in Figure 1 . which shows the disposition of ference

The effects of mandatory HACCP implementation on microbiological indicators of process hygiene in meat processing and retail establishments in Serbia.

PubMed

Tomasevic, Igor; Kuzmanović, Jelena; Anđelković, Aleksandra; Saračević, Miroslava; Stojanović, Marija M; Djekic, Ilija

2016-04-01

A total of 48,246 microbiological test results were collected from 130 meat processing plants and 220 meat retail facilities over a seven year period: 41 months before and 43 months after HACCP implementation. Our results confirm a strong positive effect of mandatory HACCP implementation on process hygiene indicators in meat establishments. Significant reductions were observed in the number of hygiene indicator organisms on all types of surfaces examined and types of meat establishments investigated. The improvement of process hygiene was articulated as aerobic colony count reduction of at least 1.0 log10 CFU/cm(2) for food contact surfaces and over 2 log10 CFU/cm(2) for cooling facilities (refrigerators, freezers and other meat cooling devices). Meat handlers' hands hygiene was least positively affected. The period after mandatory HACCP implementation was also marked by a steady decline of positive Enterobacteriaceae and Staphylococcus samples. Process hygiene advances for meat processing plants and meat retail facilities were similar. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance criteria and quality indicators for the post-analytical phase.

PubMed

Sciacovelli, Laura; Aita, Ada; Padoan, Andrea; Pelloso, Michela; Antonelli, Giorgia; Piva, Elisa; Chiozza, Maria Laura; Plebani, Mario

2016-07-01

Quality indicators (QIs) used as performance measurements are an effective tool in accurately estimating quality, identifying problems that may need to be addressed, and monitoring the processes over time. In Laboratory Medicine, QIs should cover all steps of the testing process, as error studies have confirmed that most errors occur in the pre- and post-analytical phase of testing. Aim of the present study is to provide preliminary results on QIs and related performance criteria in the post-analytical phase. This work was conducted according to a previously described study design based on the voluntary participation of clinical laboratories in the project on QIs of the Working Group "Laboratory Errors and Patient Safety" (WG-LEPS) of the International Federation of Clinical Chemistry and Laboratory Medicine (IFCC). Overall, data collected highlighted an improvement or stability in performances over time for all reported indicators thus demonstrating that the use of QIs is effective in the quality improvement strategy. Moreover, QIs data are an important source for defining the state-of-the-art concerning the error rate in the total testing process. The definition of performance specifications based on the state-of-the-art, as suggested by consensus documents, is a valuable benchmark point in evaluating the performance of each laboratory. Laboratory tests play a relevant role in the monitoring and evaluation of the efficacy of patient outcome thus assisting clinicians in decision-making. Laboratory performance evaluation is therefore crucial to providing patients with safe, effective and efficient care.

Evaluation of HIV testing algorithms in Ethiopia: the role of the tie-breaker algorithm and weakly reacting test lines in contributing to a high rate of false positive HIV diagnoses.

PubMed

Shanks, Leslie; Siddiqui, M Ruby; Kliescikova, Jarmila; Pearce, Neil; Ariti, Cono; Muluneh, Libsework; Pirou, Erwan; Ritmeijer, Koert; Masiga, Johnson; Abebe, Almaz

2015-02-03

In Ethiopia a tiebreaker algorithm using 3 rapid diagnostic tests (RDTs) in series is used to diagnose HIV. Discordant results between the first 2 RDTs are resolved by a third 'tiebreaker' RDT. Médecins Sans Frontières uses an alternate serial algorithm of 2 RDTs followed by a confirmation test for all double positive RDT results. The primary objective was to compare the performance of the tiebreaker algorithm with a serial algorithm, and to evaluate the addition of a confirmation test to both algorithms. A secondary objective looked at the positive predictive value (PPV) of weakly reactive test lines. The study was conducted in two HIV testing sites in Ethiopia. Study participants were recruited sequentially until 200 positive samples were reached. Each sample was re-tested in the laboratory on the 3 RDTs and on a simple to use confirmation test, the Orgenics Immunocomb Combfirm® (OIC). The gold standard test was the Western Blot, with indeterminate results resolved by PCR testing. 2620 subjects were included with a HIV prevalence of 7.7%. Each of the 3 RDTs had an individual specificity of at least 99%. The serial algorithm with 2 RDTs had a single false positive result (1 out of 204) to give a PPV of 99.5% (95% CI 97.3%-100%). The tiebreaker algorithm resulted in 16 false positive results (PPV 92.7%, 95% CI: 88.4%-95.8%). Adding the OIC confirmation test to either algorithm eliminated the false positives. All the false positives had at least one weakly reactive test line in the algorithm. The PPV of weakly reacting RDTs was significantly lower than those with strongly positive test lines. The risk of false positive HIV diagnosis in a tiebreaker algorithm is significant. We recommend abandoning the tie-breaker algorithm in favour of WHO recommended serial or parallel algorithms, interpreting weakly reactive test lines as indeterminate results requiring further testing except in the setting of blood transfusion, and most importantly, adding a confirmation test to the RDT algorithm. It is now time to focus research efforts on how best to translate this knowledge into practice at the field level. Clinical Trial registration #: NCT01716299.

Development and characterization of decellularized human nasoseptal cartilage matrix for use in tissue engineering.

PubMed

Graham, M Elise; Gratzer, Paul F; Bezuhly, Michael; Hong, Paul

2016-10-01

Reconstruction of cartilage defects in the head and neck can require harvesting of autologous cartilage grafts, which can be associated with donor site morbidity. To overcome this limitation, tissue-engineering approaches may be used to generate cartilage grafts. The objective of this study was to decellularize and characterize human nasoseptal cartilage with the aim of generating a biological scaffold for cartilage tissue engineering. Laboratory study using nasoseptal cartilage. Remnant human nasoseptal cartilage specimens were collected and subjected to a novel decellularization treatment. The decellularization process involved several cycles of enzymatic detergent treatments. For characterization, decellularized and fresh (control) specimens underwent histological, biochemical, and mechanical analyses. Scanning electron microscopy and biocompatibility assay were also performed. The decellularization process had minimal effect on glycosaminoglycan content of the cartilage extracellular matrix. Deoxyribonucleic acid (DNA) analysis revealed the near-complete removal of genomic DNA from decellularized tissues. The effectiveness of the decellularization process was also confirmed on histological and scanning electron microscopic analyses. Mechanical testing results showed that the structural integrity of the decellularized tissue was maintained, and biocompatibility was confirmed. Overall, the current decellularization treatment resulted in significant reduction of genetic/cellular material with preservation of the underlying extracellular matrix structure. This decellularized material may serve as a potential scaffold for cartilage tissue engineering. N/A. Laryngoscope, 126:2226-2231, 2016. © 2016 The American Laryngological, Rhinological and Otological Society, Inc.

Production of thick uniform-coating films containing rectorite on nanofibers through the use of an automated coating machine.

PubMed

Wu, Yang; Li, Xueyong; Shi, Xiaowen; Zhan, Yingfei; Tu, Hu; Du, Yumin; Deng, Hongbing; Jiang, Linbin

2017-01-01

When an efficient automated coating machine is used to process layer-by-layer (LBL) deposited nanofibrous mats, it causes an obvious planar effect on the surface of the mats, which can be eliminated through ultimate immersion. During this process, chitosan (CS) - rectorite (REC) intercalated composite films are built on the surface of cellulose acetate (CA) nanofibrous mats by a coating machine. Then, the immersion process is utilized to allow positively charged CS or CS-REC intercalated composites to uniformly assemble on the surface of negatively charged CA nanofibers. An investigation into the morphology of the resultant scaffolds confirms that the uniquely small pore size, high specific surface area and typically three-dimensional (3D) structure of nanofibrous mats remain present. The results of Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) indicate that it is feasible to assemble nanofibrous mats using a coating machine. The intercalated structure of CS-REC is confirmed by the results of small-angle X-ray diffraction (SAXRD) and wide-angle X-ray diffraction (WAXRD). The results of the cell experiment and antibacterial test demonstrate that the addition of REC not only has little impact on the cytocompatibility of the mats but also enhances their ability to inhibit bacteria. Copyright © 2016 Elsevier B.V. All rights reserved.

Low-frequency pitch perception in children with cochlear implants in comparison to normal hearing peers.

PubMed

Dincer D'Alessandro, Hilal; Filipo, Roberto; Ballantyne, Deborah; Attanasio, Giuseppe; Bosco, Ersilia; Nicastri, Maria; Mancini, Patrizia

2015-11-01

The aim of the present study was to investigate the application of two new pitch perception tests in children with cochlear implants (CI) and to compare CI outcomes to normal hearing (NH) children, as well as investigating the effect of chronological age on performance. The tests were believed to be linked to the availability of Temporal Fine Structure (TFS) cues. 20 profoundly deaf children with CI (5-17 years) and 31 NH peers participated in the study. Harmonic Intonation (HI) and Disharmonic Intonation (DI) tests were used to measure low-frequency pitch perception. HI/DI outcomes were found poorer in children with CI. CI and NH groups showed a statistically significant difference (p < 0.001). HI scores were better than those of DI test (p < 0.001). Chronological age had a significant effect on DI performance in NH group (p < 0.05); children under the age of 8.5 years showed larger inter-subject-variability; however, the majority of NH children showed outcomes that were considered normal at adult-level. For the DI test, bimodal listeners had better performance than when listening with CI alone. HI/DI tests were applicable as clinical tools in the pediatric population. The majority of CI users showed abnormal outcomes on both tests confirming poor TFS processing in the hearing-impaired population. Findings indicated that the DI test provided more differential low-frequency pitch perception outcomes in that it reflected phase locking and TFS processing capacities of the ear, whereas HI test provided information of its place coding capacity as well.

Challenges in Interpretation of Diagnostic Test Results in a Mumps Outbreak in a Highly Vaccinated Population.

PubMed

Trotz-Williams, L A; Mercer, N J; Paphitis, K; Walters, J M; Wallace, D; Kristjanson, E; Gubbay, J; Mazzulli, T

2017-02-01

In spite of a greatly reduced incidence rate due to vaccination, mumps outbreaks continue to occur in several areas of the world, sometimes in vaccinated populations. This article describes an outbreak in a highly vaccinated population in southwestern Ontario, Canada, and the challenges encountered in interpreting the results of diagnostic tests used in the outbreak. During the outbreak, patients were interviewed and classified according to the outbreak case definition, and specimens were collected for diagnostic testing according to Ontario guidelines. Twenty-seven individuals were classified as confirmed cases (n = 19) or suspect cases (n = 8) according to the case definition, only 9 of which were laboratory-confirmed cases: 7 confirmed by reverse transcriptase PCR (RT-PCR) and 2 by IgM serology. All 19 confirmed cases represented patients who were associated with secondary schools in the local area and had been vaccinated against mumps with one (n = 2) or two (n = 17) doses of the measles-mumps-rubella (MMR) vaccine. This is the first published report of an outbreak of mumps in Ontario in which all confirmed cases had been vaccinated against the disease. It highlights the limitations of and difficulties in interpreting current mumps diagnostic tests when used in vaccinated individuals. Copyright © 2017 American Society for Microbiology.

Challenges in Interpretation of Diagnostic Test Results in a Mumps Outbreak in a Highly Vaccinated Population

PubMed Central

Mercer, N. J.; Paphitis, K.; Walters, J. M.; Wallace, D.; Kristjanson, E.; Gubbay, J.; Mazzulli, T.

2016-01-01

ABSTRACT In spite of a greatly reduced incidence rate due to vaccination, mumps outbreaks continue to occur in several areas of the world, sometimes in vaccinated populations. This article describes an outbreak in a highly vaccinated population in southwestern Ontario, Canada, and the challenges encountered in interpreting the results of diagnostic tests used in the outbreak. During the outbreak, patients were interviewed and classified according to the outbreak case definition, and specimens were collected for diagnostic testing according to Ontario guidelines. Twenty-seven individuals were classified as confirmed cases (n = 19) or suspect cases (n = 8) according to the case definition, only 9 of which were laboratory-confirmed cases: 7 confirmed by reverse transcriptase PCR (RT-PCR) and 2 by IgM serology. All 19 confirmed cases represented patients who were associated with secondary schools in the local area and had been vaccinated against mumps with one (n = 2) or two (n = 17) doses of the measles-mumps-rubella (MMR) vaccine. This is the first published report of an outbreak of mumps in Ontario in which all confirmed cases had been vaccinated against the disease. It highlights the limitations of and difficulties in interpreting current mumps diagnostic tests when used in vaccinated individuals. PMID:28003216

Final Report - Melt Rate Enhancement for High Aluminum HLW Glass Formulation, VSL-08R1360-1, Rev. 0, dated 12/19/08

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, Albert A.; Pegg, I. L.; Chaudhuri, M.

2013-11-13

The principal objective of the work reported here was to develop and identify HLW glass compositions that maximize waste processing rates for the aluminum limted waste composition specified by ORP while maintaining high waste loadings and acceptable glass properties. This was accomplished through a combination of crucible-scale tests, confirmation tests on the DM100 melter system, and demonstration at pilot scale (DM1200). The DM100-BL unit was selected for these tests since it was used previously with the HLW waste streams evaluated in this study, was used for tests on HLW glass compositions to support subsequent tests on the HLW Pilot Melter,more » conduct tests to determine the effect of various glass properties (viscosity and conductivity) and oxide concentrations on glass production rates with HLW feed streams, and to assess the volatility of cesium and technetium during the vitrification of an HLW AZ-102 composition. The same melter was selected for the present tests in order to maintain comparisons between the previously collected data. These tests provide information on melter processing characteristics and off-gas data, including formation of secondary phases and partitioning. Once DM100 tests were completed, one of the compositions was selected for further testing on the DM1200; the DM1200 system has been used for processing a variety of simulated Hanford waste streams. Tests on the larger melter provide processing data at one third of the scale of the actual WTP HLW melter and, therefore, provide a more accurate and reliable assessment of production rates and potential processing issues. The work focused on maximizing waste processing rates for high aluminum HLW compositions. In view of the diversity of forms of aluminum in the Hanford tanks, tests were also conducted on the DM100 to determine the effect of changes in the form of aluminum on feed properties and production rate. In addition, the work evaluated the effect on production rate of modest increases in melter operating temperature. Glass composition development was based on one of the HLW waste compositions specified by ORP that has a high concentration of aluminum. Small-scale tests were used to provide an initial screening of various glass formulations with respect to melt rates; more definitive screening was provided by the subsequent DM100 tests. Glass properties evaluated included: viscosity, electrical conductivity, crystallinity, gross glass phase separation and the 7- day Product Consistency Test (ASTM-1285). Glass property limits were based upon the reference properties for the WTP HLW melter. However, the WTP crystallinity limit (< 1 vol% at 950oC) was relaxed slightly as a waste loading constraint for the crucible melts.« less

Exploring Selective Exposure and Confirmation Bias as Processes Underlying Employee Work Happiness: An Intervention Study

PubMed Central

Williams, Paige; Kern, Margaret L.; Waters, Lea

2016-01-01

Employee psychological capital (PsyCap), perceptions of organizational virtue (OV), and work happiness have been shown to be associated within and over time. This study examines selective exposure and confirmation bias as potential processes underlying PsyCap, OV, and work happiness associations. As part of a quasi-experimental study design, school staff (N = 69) completed surveys at three time points. After the first assessment, some staff (n = 51) completed a positive psychology training intervention. Results of descriptive statistics, correlation, and regression analyses on the intervention group provide some support for selective exposure and confirmation bias as explanatory mechanisms. In focusing on the processes through which employee attitudes may influence work happiness this study advances theoretical understanding, specifically of selective exposure and confirmation bias in a field study context. PMID:27378978

Assessment of the Efficiency of Consolidation Treatment through Injections of Expanding Resins by Geotechnical Tests and 3D Electrical Resistivity Tomography

PubMed Central

2015-01-01

The design and execution of consolidation treatment of settled foundations by means of injection of polyurethane expanding resins require a proper investigation of the state of the foundation soil, in order to better identify anomalies responsible for the instability. To monitor the injection process, a procedure has been developed, which involves, in combination with traditional geotechnical tests, the application of a noninvasive, geophysical technique based on the electrical resistivity, which is strongly sensitive to presence of water or voids. Three-dimensional electrical resistivity tomography is a useful tool to produce effective 3D images of the foundation soils before, during, and after the injections. The achieved information allows designing the consolidation scheme and monitoring its effects on the treated volumes in real time. To better understand the complex processes induced by the treatment and to learn how variations of resistivity accompany increase of stiffness, an experiment was carried out in a full-scale test site. Injections of polyurethane expanding resin were performed as in real worksite conditions. Results confirm that the experimented approach by means of 3D resistivity imaging allows a reliable procedure of consolidation, and geotechnical tests demonstrate the increase of mechanical stiffness. PMID:26167521

In vivo antinociceptive and anti-inflammatory activities of dried and fermented processed virgin coconut oil.

PubMed

Zakaria, Z A; Somchit, M N; Mat Jais, A M; Teh, L K; Salleh, M Z; Long, K

2011-01-01

The present study was carried out to investigate the antinociceptive and anti-inflammatory activities of virgin coconut oil (VCO) produced by the Malaysian Agriculture Research and Development Institute (MARDI) using various in vivo models. Two types of VCOs, produced via standard drying (VCOA) and fermentation (VCOB) processes were used in this study. Both VCOA and VCOB were serially diluted using 1% Tween 80 to concentrations (v/v) of 10, 50 and 100%. Antinociceptive and anti- inflammatory activities of both VCOs were examined using various in vivo model systems. The antinociceptive activity of the VCOs were compared to those of 1% Tween 80 (used as a negative control), morphine (5 mg/kg) and/or acetylsalicylic acid (100 mg/kg). Both VCOA and VCOB exhibited significant (p < 0.05) dose-dependent antinociceptive activity in the acetic acid-induced writhing test. Both VCOs also exerted significant (p < 0.05) antinociceptive activity in both phases of the formalin and hot-plate tests. Interestingly, the VCOs exhibited anti-inflammatory activity in an acute (carrageenan-induced paw edema test), but not in a chronic (cotton-pellet-induced granuloma test) model of inflammation. The MARDI-produced VCOs possessed antinociceptive and anti-inflammatory activities. Further studies are needed to confirm these observations. Copyright © 2011 S. Karger AG, Basel.

Opioids in oral fluid of Spanish drivers.

PubMed

Herrera-Gómez, Francisco; García-Mingo, Mercedes; Colás, Mónica; González-Luque, Juan Carlos; Álvarez, F Javier

2018-06-01

Driving under the influence of certain drugs is not allowed, and roadside drug testing is being considered an important tool for deterring driving under the influence of them. This study aimed to assess the presence and concentration of opioids, as well as their combined use with other drugs (laboratory confirmation after the on-road screening) in Spanish drivers between 2011 and 2016. In Spain, mandatory roadside breath alcohol and oral fluid drug testing (screening) are carried out by the Traffic Police using Dräger Alcotest ® 6810 device, and Dräger DrugTest ® 5000, DrugWipe ® , or Alere™ DDS ® 2 Mobile Test System. For positive cases in the period covered, 65,244, confirmation analysis and quantification using chromatographic techniques were performed. Opioids were confirmed in 8.6% of positive cases, being 7.2% positives to 6-acetylmorphine (6-AM), 6.5% to morphine, 5.4% to codeine, and 4.1% to methadone. The majority of the confirmed tests for morphine (96.5%), codeine (88.4%) and methadone (81.9) were also positive for 6-AM. The presence of other drugs, particularly cocaine and cannabis, was very common. Concentration values reached important levels. Positive results for morphine (0.1%), codeine (0.6%) or methadone (0.4%) alone were very infrequent. Drivers with a confirmed positive roadside test for morphine, codeine, and methadone had also consumed heroin and/or other illicit drugs, such as cocaine and/or THC, and at relevant concentrations. Improving interventions to combat the problem of driving under the influence of driving-impairing substances is a priority. Copyright © 2018 Elsevier B.V. All rights reserved.

Depletion of nucleus accumbens dopamine leads to impaired reward and aversion processing in mice: Relevance to motivation pathologies.

PubMed

Bergamini, Giorgio; Sigrist, Hannes; Ferger, Boris; Singewald, Nicolas; Seifritz, Erich; Pryce, Christopher R

2016-10-01

Dopamine (DA) neurotransmission, particularly the ventral tegmental area-nucleus accumbens (VTA-NAcc) projection, underlies reward and aversion processing, and deficient DA function could underlie motivational impairments in psychiatric disorders. 6-hydroxydopamine (6-OHDA) injection is an established method for chronic DA depletion, principally applied in rat to study NAcc DA regulation of reward motivation. Given the increasing focus on studying environmental and genetic regulation of DA function in mouse models, it is important to establish the effects of 6-OHDA DA depletion in mice, in terms of reward and aversion processing. This mouse study investigated effects of 6-OHDA-induced NAcc DA depletion using the operant behavioural test battery of progressive ratio schedule (PRS), learned non-reward (LNR), learned helplessness (LH), treadmill, and in addition Pavlovian fear conditioning. 6-OHDA NAcc DA depletion, confirmed by ex vivo HPLC-ED, reduced operant responding: for gustatory reward under effortful conditions in the PRS test; to a stimulus recently associated with gustatory non-reward in the LNR test; to escape footshock recently experienced as uncontrollable in the LH test; and to avoid footshock by physical effort in the treadmill test. Evidence for specificity of effects to NAcc DA was provided by lack of effect of medial prefrontal cortex DA depletion in the LNR and LH tests. These findings add significantly to the evidence that NAcc DA is a major regulator of behavioural responding, particularly at the motivational level, to both reward and aversion. They demonstrate the suitability of mouse models for translational study of causation and reversal of pathophysiological DA function underlying motivation psychopathologies. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solid oxide membrane (SOM) process for ytterbium and silicon production from their oxides

NASA Astrophysics Data System (ADS)

Jiang, Yihong

The Solid oxide membrane (SOM) electrolysis is an innovative green technology that produces technologically important metals directly from their respective oxides. A yttria-stabilized zirconia (YSZ) tube, closed at one end is employed to separate the molten salt containing dissolved metal oxides from the anode inside the YSZ tube. When the applied electric potential between the cathode in the molten salt and the anode exceeds the dissociation potential of the desired metal oxides, oxygen ions in the molten salt migrate through the YSZ membrane and are oxidized at the anode while the dissolved metal cations in the flux are reduced to the desired metal at the cathode. Compared with existing metal production processes, the SOM process has many advantages such as one unit operation, less energy consumption, lower capital costs and zero carbon emission. Successful implementation of the SOM electrolysis process would provide a way to mitigate the negative environmental impact of the metal industry. Successful demonstration of producing ytterbium (Yb) and silicon (Si) directly from their respective oxides utilizing the SOM electrolysis process is presented in this dissertation. During the SOM electrolysis process, Yb2O3 was reduced to Yb metal on an inert cathode. The melting point of the supporting electrolyte (LiF-YbF3-Yb2O3) was determined by differential thermal analysis (DTA). Static stability testing confirmed that the YSZ tube was stable with the flux at operating temperature. Yb metal deposit on the cathode was confirmed by scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS). During the SOM electrolysis process for silicon production, a fluoride based flux based on BaF2, MgF2, and YF3 was engineered to serve as the liquid electrolyte for dissolving silicon dioxide. YSZ tube was used to separate the molten salt from an anode current collector in the liquid silver. Liquid tin was chosen as cathode to dissolve the reduced silicon during SOM electrolysis. After electrolysis, upon cooling, silicon crystals precipitated out from the Si-Sn liquid alloy. The presence of high-purity silicon crystals in the liquid tin cathode was confirmed by SEM/EDS. The fluoride based flux was also optimized to improve YSZ membrane stability for long-term use.

Prevalence of human immunodeficiency virus type 1 p24 antigen in U.S. blood donors--an assessment of the efficacy of testing in donor screening. The HIV-Antigen Study Group.

PubMed

Alter, H J; Epstein, J S; Swenson, S G; VanRaden, M J; Ward, J W; Kaslow, R A; Menitove, J E; Klein, H G; Sandler, S G; Sayers, M H

1990-11-08

We performed a multicenter study in 1989 to determine whether screening whole-blood donors for human immunodeficiency virus type 1 (HIV-1) p24 antigen would improve transfusion safety by identifying carriers of the virus who are seronegative for HIV-1 antibody. More than 500,000 donations were tested at 13 U.S. blood centers with test kits from two manufacturers. Units found repeatedly reactive were retested in a central laboratory; if the results were positive, they were confirmed by a neutralization assay. A subgroup of units was also tested for HIV-1 by the polymerase chain reaction. Selected donors confirmed or not confirmed as having p24 antigen were contacted for follow-up interviews to identify risk factors and undergo retesting for HIV-1 markers. Positive tests for p24 antigen were confirmed by neutralization in five donors (0.001 percent of all donations tested), all of whom were also positive for HIV-1 antibody and HIV-1 by polymerase chain reaction. Three of the antigen-positive donors had other markers of infectious disease that would have resulted in the exclusion of their blood; two had risk factors for HIV-1 that should have led to self-exclusion. Of 220 blood units with repeatedly reactive p24 antigen whose presence could not be confirmed by neutralization (0.04 percent of the donations studied), none were positive for HIV-1 antibody, HIV-1 by polymerase chain reaction (120 units tested), or virus culture (76 units tested)--attesting to the specificity of confirmatory neutralization. The finding that no donation studied was positive for p24 antigen and negative for HIV-1 antibody suggests that screening donors for p24 antigen with tests of the current level of sensitivity would not add substantially to the safety of the U.S. blood supply.

Impairment of retinal increment thresholds in Huntington's disease.

PubMed

Paulus, W; Schwarz, G; Werner, A; Lange, H; Bayer, A; Hofschuster, M; Müller, N; Zrenner, E

1993-10-01

We have investigated detection thresholds for a foveal blue test light using a Maxwellian view system in 61 normal subjects, 19 patients with Huntington's chorea, 14 patients with Tourette's syndrome, and 20 patients with schizophrenia. Ten measurements were made: The blue test light (1 degree diameter, 500 msec duration) was presented either superimposed on a yellow adaptation field (5 degree diameter) or 500 msec after switching off this field (transient tritanopia effect). In both cases five different background intensities were presented. The only abnormality found was in patients with Huntington's chorea. During adaptation these patients' thresholds are significantly higher than normal (p < 0.005). No change was found in the transient tritanopia effect. Huntington's disease causes degeneration of several different transmitter systems in the brain. Increment threshold testing allows for noninvasive investigation of patients and confirms the involvement of the retina in the degenerative process in Huntington's chorea.

Aft Skirt Electrical Umbilical (ASEU) and Vehicle Support Post (

NASA Image and Video Library

2016-12-09

A view from underneath one of the vertical support posts for NASA's Space Launch System rocket. Two after skirt electrical umbilicals (ASEUs) and the first of the vertical support post were transported by flatbed truck from the Launch Equipment Test Facility to the Mobile Launcher Yard as NASA's Kennedy Space Center in Florida. The ASEUs and the VSP underwent a series of tests to confirm they are functioning properly and ready to support the SLS for launch. The ASEUs will connect to the SLS rocket at the bottom outer edge of each booster and provide electrical power and data connections to the rocket until it lifts off from the launch pad. The eight VSPs will support the load of the solid rocket boosters, with four posts for each of the boosters. The center’s Engineering Directorate and the Ground Systems Development and Operations Program are overseeing processing and testing of the umbilicals.

Aft Skirt Electrical Umbilical (ASEU) and Vehicle Support Post (

NASA Image and Video Library

2016-12-09

Construction workers assist as a crane is used to lower a vertical support post for NASA's Space Launch System (SLS) onto a platform at the Mobile Launcher Yard at NASA's Kennedy Space Center in Florida. Two ASEUs and the first of the vertical support posts underwent a series of tests at the Launch Equipment Test Facility to confirm they are functioning properly and ready to support the SLS for launch. The ASEUs will connect to the SLS rocket at the bottom outer edge of each booster and provide electrical power and data connections to the rocket until it lifts off from the launch pad. The eight VSPs will support the load of the solid rocket boosters, with four posts for each of the boosters. The center’s Engineering Directorate and the Ground Systems Development and Operations Program are overseeing processing and testing of the umbilicals.

FY2000 FRED Test Report - Final Report on the Crossflow Filter Optimization with 5.6M Sodium Salt Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M.R.

2001-04-04

The Filtration Research Engineering Demonstration (FRED) at the University of South Carolina ran a test campaign to confirm the utility of crossflow filtration for use with the MST sorption as a strontium-actinide removal technology that is expected to be coupled with the ion exchange and solvent extraction process alternatives. FRED has a Mott Metallurgical 7 tube filter with individual tubes 10 ft long and 3/4 inch o.d. having a nominal pore size of 0.5 microns. The blend sludge consisted of a 50/50 wt percent mixture of sludge simulants of SRS Tank 40H and Tank 8F simulated sludges previously manufactured atmore » FRED. Monosodium Titanate (MST) was blended with the 50/50 sludge mixture in a proportion of 0.9167 MST-to-Sludge ratio to provide the solids loadings analyzed in this test.« less

An Investigation of the Cryogenic Freezing of Water in Non-Metallic Pipelines

NASA Astrophysics Data System (ADS)

Martin, C. I.; Richardson, R. N.; Bowen, R. J.

2004-06-01

Pipe freezing is increasingly used in a range of industries to solve otherwise intractable pipe line maintenance and servicing problems. This paper presents the interim results from an experimental study on deliberate freezing of polymeric pipelines. Previous and contemporary works are reviewed. The object of the current research is to confirm the feasibility of ice plug formation within a polymeric pipe as a method of isolation. Tests have been conducted on a range of polymeric pipes of various sizes. The results reported here all relate to freezing of horizontal pipelines. In each case the process of plug formation was photographed, the frozen plug pressure tested and the pipe inspected for signs of damage resulting from the freeze procedure. The time to freeze was recorded and various temperatures logged. These tests have demonstrated that despite the poor thermal and mechanical properties of the polymers, freezing offers a viable alternative method of isolation in polymeric pipelines.

NASA-DoD Lower Process Temperature Lead-Free Solder Project Overview

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2014-01-01

This project is a follow-on effort to the Joint Council on Aging AircraftJoint Group on Pollution Prevention (JCAAJG-PP) Pb-free Solder Project and NASA-DoD Lead-Free Electronics Project which were the first projects to test the reliability of Pb-free solder joints against the requirements of the aerospace and military community. This effort would continue to build on the results from the JCAAJG-PP Lead-Free Solder Project and NASA-DoD Lead-Free Electronics Project while focusing on a particular failure mechanism currently plaguing Pb-free assemblies, pad cratering.The NASA-DoD Lead-Free Electronics Project confirmed that pad cratering is one of the dominant failure modes that occur in various board level reliability tests, especially under dynamic loading. Pad Cratering is a latent defect that may occur during assembly, rework, and post assembly handling and testing.

Measurements of thermal conductivity and the coefficient of thermal expansion for polysilicon thin films by using double-clamped beams

NASA Astrophysics Data System (ADS)

Liu, Haiyun; Wang, Lei

2018-01-01

In this paper, a test structure for simultaneously determining thermal conductivity and the coefficient of thermal expansion (CTE) of polysilicon thin film is proposed. The test structure consists of two double-clamped beams with different lengths. A theoretical model for extracting thermal conductivity and CTE based on electrothermal analysis and resonance frequency approach is developed. Both flat and buckled beams are considered in the theoretical model. The model is confirmed by finite element software ANSYS. The test structures are fabricated by surface micromachined fabrication process. Experiments are carried out in our atmosphere. Thermal conductivity and CTE of polysilicon thin film are obtained to be (29.96  ±  0.92) W · m · K-1 and (2.65  ±  0.03)  ×  10-6 K-1, respectively, with temperature ranging from 300-400 K.

Development of the Global Measles Laboratory Network.

PubMed

Featherstone, David; Brown, David; Sanders, Ray

2003-05-15

The routine reporting of suspected measles cases and laboratory testing of samples from these cases is the backbone of measles surveillance. The Global Measles Laboratory Network (GMLN) has developed standards for laboratory confirmation of measles and provides training resources for staff of network laboratories, reference materials and expertise for the development and quality control of testing procedures, and accurate information for the Measles Mortality Reduction and Regional Elimination Initiative. The GMLN was developed along the lines of the successful Global Polio Laboratory Network, and much of the polio laboratory infrastructure was utilized for measles. The GMLN has developed as countries focus on measles control activities following successful eradication of polio. Currently more than 100 laboratories are part of the global network and follow standardized testing and reporting procedures. A comprehensive laboratory accreditation process will be introduced in 2002 with six quality assurance and performance indicators.

Cold crucible induction melter test for crystalline ceramic waste form fabrication: A feasibility assessment

DOE PAGES

Amoroso, Jake W.; Marra, James; Dandeneau, Christopher S.; ...

2017-01-18

The first scaled proof-of-principle cold crucible induction melter (CCIM) test to process a multiphase ceramic waste form from a simulated combined (Cs/Sr, lanthanide and transition metal fission products) commercial used nuclear fuel waste stream was recently conducted in the United States. X-ray diffraction, 2-D X-ray absorption near edge structure (XANES), electron microscopy, inductively coupled plasma-atomic emission spectroscopy (and inductively coupled plasma-mass spectroscopy for Cs), and product consistency tests were used to characterize the fabricated CCIM material. Characterization analyses confirmed that a crystalline ceramic with a desirable phase assemblage was produced from a melt using a CCIM. We identified primary hollandite,more » pyrochlore/zirconolite, and perovskite phases in addition to minor phases rich in Fe, Al, or Cs. The material produced in the CCIM was chemically homogeneous and displayed a uniform phase assemblage with acceptable aqueous chemical durability.« less

On the Mineral and Vegetal Oils Used as Electroinsulation in Transformers

NASA Astrophysics Data System (ADS)

Şerban, Mariana; Sângeorzan, Livia; Helerea, Elena

Due to the relatively large availability and reduced price, the mineral transformer oils are widely used as electrical insulating liquids. However, mineral oil drastically degrades over time in service. New efforts were made to improve mineral oils characteristics, and other types of liquids like vegetal oils are proposed. This paper deals with new comparative tests on mineral and vegetal oils using as indicator the electric strength. The samples of non-additive mineral oil type TR 30 and vegetal oils of rape, sunflower and corn have been tested with increasing voltage of 60 Hz using different electrodes. The obtained data have been statistical processed. The analyze shows different average values of electrical strength for the different type of sample. New method of testing through electrical breakdown is proposed. Experimental data confirms that it is possible to use as electroinsulation organic vegetal oils in power transformers.

Development of scale deposit inhibition technology using turbine water-cooled nozzle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saito, S.; Sakanashi, H.; Suzuki, T.

1995-12-31

The scale deposition onto turbines in geothermal power stations is usually regarded as unavoidable whereas this is one of the most serious concerns which can affect the interval of periodical inspections. In common practice, scale is removed manually and mechanically during periodical inspections of power stations, but there are some cases of geothermal power stations where scale is removed from the turbines without stopping turbines by practicing the turbine washing operation. The jointly developed technology by Tohoku Electric Power Co., Ltd. and Mitsubishi Heavy Industries, Ltd. in the present work, is a technique capable preventing scale deposition and precipitation bymore » water-cooling the turbine first stage nozzle subjected to the highest deposition of scale and its effect has been confirmed through its model in the field test. This paper presents these test processes and the test results.« less

CONORBIT: constrained optimization by radial basis function interpolation in trust regions

DOE PAGES

Regis, Rommel G.; Wild, Stefan M.

2016-09-26

Here, this paper presents CONORBIT (CONstrained Optimization by Radial Basis function Interpolation in Trust regions), a derivative-free algorithm for constrained black-box optimization where the objective and constraint functions are computationally expensive. CONORBIT employs a trust-region framework that uses interpolating radial basis function (RBF) models for the objective and constraint functions, and is an extension of the ORBIT algorithm. It uses a small margin for the RBF constraint models to facilitate the generation of feasible iterates, and extensive numerical tests confirm that such a margin is helpful in improving performance. CONORBIT is compared with other algorithms on 27 test problems, amore » chemical process optimization problem, and an automotive application. Numerical results show that CONORBIT performs better than COBYLA, a sequential penalty derivative-free method, an augmented Lagrangian method, a direct search method, and another RBF-based algorithm on the test problems and on the automotive application.« less

4D-SFM Photogrammetry for Monitoring Sediment Dynamics in a Debris-Flow Catchment: Software Testing and Results Comparison

NASA Astrophysics Data System (ADS)

Cucchiaro, S.; Maset, E.; Fusiello, A.; Cazorzi, F.

2018-05-01

In recent years, the combination of Structure-from-Motion (SfM) algorithms and UAV-based aerial images has revolutionised 3D topographic surveys for natural environment monitoring, offering low-cost, fast and high quality data acquisition and processing. A continuous monitoring of the morphological changes through multi-temporal (4D) SfM surveys allows, e.g., to analyse the torrent dynamic also in complex topography environment like debris-flow catchments, provided that appropriate tools and procedures are employed in the data processing steps. In this work we test two different software packages (3DF Zephyr Aerial and Agisoft Photoscan) on a dataset composed of both UAV and terrestrial images acquired on a debris-flow reach (Moscardo torrent - North-eastern Italian Alps). Unlike other papers in the literature, we evaluate the results not only on the raw point clouds generated by the Structure-from- Motion and Multi-View Stereo algorithms, but also on the Digital Terrain Models (DTMs) created after post-processing. Outcomes show differences between the DTMs that can be considered irrelevant for the geomorphological phenomena under analysis. This study confirms that SfM photogrammetry can be a valuable tool for monitoring sediment dynamics, but accurate point cloud post-processing is required to reliably localize geomorphological changes.

Taguchi experimental design to determine the taste quality characteristic of candied carrot

NASA Astrophysics Data System (ADS)

Ekawati, Y.; Hapsari, A. A.

2018-03-01

Robust parameter design is used to design product that is robust to noise factors so the product’s performance fits the target and delivers a better quality. In the process of designing and developing the innovative product of candied carrot, robust parameter design is carried out using Taguchi Method. The method is used to determine an optimal quality design. The optimal quality design is based on the process and the composition of product ingredients that are in accordance with consumer needs and requirements. According to the identification of consumer needs from the previous research, quality dimensions that need to be assessed are the taste and texture of the product. The quality dimension assessed in this research is limited to the taste dimension. Organoleptic testing is used for this assessment, specifically hedonic testing that makes assessment based on consumer preferences. The data processing uses mean and signal to noise ratio calculation and optimal level setting to determine the optimal process/composition of product ingredients. The optimal value is analyzed using confirmation experiments to prove that proposed product match consumer needs and requirements. The result of this research is identification of factors that affect the product taste and the optimal quality of product according to Taguchi Method.

10 CFR 26.103 - Determining a confirmed positive test result for alcohol.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Determining a confirmed positive test result for alcohol. 26.103 Section 26.103 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting... fitness indicates that the donor is fit to safely and competently perform his or her duties. ...

10 CFR 26.103 - Determining a confirmed positive test result for alcohol.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Determining a confirmed positive test result for alcohol. 26.103 Section 26.103 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting... fitness indicates that the donor is fit to safely and competently perform his or her duties. ...

10 CFR 26.103 - Determining a confirmed positive test result for alcohol.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Determining a confirmed positive test result for alcohol. 26.103 Section 26.103 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting... fitness indicates that the donor is fit to safely and competently perform his or her duties. ...

10 CFR 26.103 - Determining a confirmed positive test result for alcohol.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Determining a confirmed positive test result for alcohol. 26.103 Section 26.103 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting... fitness indicates that the donor is fit to safely and competently perform his or her duties. ...

10 CFR 26.103 - Determining a confirmed positive test result for alcohol.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Determining a confirmed positive test result for alcohol. 26.103 Section 26.103 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting... fitness indicates that the donor is fit to safely and competently perform his or her duties. ...

Characterization of curing behavior of UV-curable LSR for LED embedded injection mold

NASA Astrophysics Data System (ADS)

Tae, Joon-Sung; Yim, Kyung-Gyu; Rhee, Byung-Ohk; Kwak, Jae B.

2016-11-01

For many applications, liquid silicone rubber (LSR) injection molding is widely used for their great design flexibility and high productivity. In particular, a sealing part for a mobile device such as smartphone and watch has been produced by injection molding. While thermally curable LSR causes deformation problem due to a high mold temperature, UV-curable LSR can be molded at room temperature, which has advantages for over-molding with inserts of temperature-sensitive materials. Ultraviolet light-emitting diodes (UV LEDs) have advantages such as a longer service life, a lower heat dissipation, and smaller size to equip into the mold than conventional halogen or mercury UV lamps. In this work, rheological behavior of UV-curable LSR during curing process was analyzed by UV LEDs available in the market. UV-LEDs of various wave lengths and intensities were tested. The steady shear test was applied to find the starting time of curing and the SAOS was applied to find the ending time of curing to estimate processing time. In addition, the hardness change with irradiation energy was compared with the rheological data to confirm the reliability of the rheological test.

Anti-mycobacterial activity of marine fungus-derived 4-deoxybostrycin and nigrosporin.

PubMed

Wang, Cong; Wang, Juan; Huang, Yuhong; Chen, Hong; Li, Yan; Zhong, Lili; Chen, Yi; Chen, Shengping; Wang, Jun; Kang, Juling; Peng, Yi; Yang, Bin; Lin, Yongcheng; She, Zhigang; Lai, Xiaomin

2013-01-29

4-Deoxybostrycin is a natural anthraquinone compound isolated from the Mangrove endophytic fungus Nigrospora sp. collected from the South China Sea. Nigrosporin is the deoxy-derivative of 4-deoxybostrycin. They were tested against mycobacteria, especially Mycobacterium tuberculosis. In the Kirby-Bauer disk diffusion susceptibility test, they both had inhibition zone sizes of over 25 mm. The results of the absolute concentration susceptibility test suggested that they had inhibitory effects against mycobacteria. Moreover, 4-deoxybostrycin exhibited good inhibition which was even better than that of first line anti-tuberculosis (TB) drugs against some clinical multidrug-resistant (MDR) M. tuberculosis strains. The gene expression profile of M. tuberculosis H37Rv after treatment with 4-deoxybostrycin was compared with untreated bacteria. One hundred and nineteen out of 3,875 genes were significantly different in M. tuberculosis exposed to 4-deoxybostrycin from control. There were 46 functionally known genes which are involved in metabolism, information storage and processing and cellular processes. The differential expressions of six genes were further confirmed by quantitative real-time polymerase chain reaction (qRT-PCR). The present study provides a useful experiment basis for exploitation of correlative new drugs against TB and for finding out new targets of anti-mycobacterial therapy.

Quantitative characterization of the interfacial adhesion of Ni thin film on steel substrate: A compression-induced buckling delamination test

NASA Astrophysics Data System (ADS)

Zhu, W.; Zhou, Y. C.; Guo, J. W.; Yang, L.; Lu, C.

2015-01-01

A compression-induced buckling delamination test is employed to quantitatively characterize the interfacial adhesion of Ni thin film on steel substrate. It is shown that buckles initiate from edge flaws and surface morphologies exhibit symmetric, half-penny shapes. Taking the elastoplasticity of film and substrate into account, a three-dimensional finite element model for an edge flaw with the finite size is established to simulate the evolution of energy release rates and phase angles in the process of interfacial buckling-driven delamination. The results show that delamination propagates along both the straight side and curved front. The mode II delamination plays a dominant role in the process with a straight side whilst the curved front experiences almost the pure mode I. Based on the results of finite element analysis, a numerical model is developed to evaluate the interfacial energy release rate, which is in the range of 250-315 J/m2 with the corresponding phase angle from -41° to -66°. These results are in agreement with the available values determined by other testing methods, which confirms the effectiveness of the numerical model.

Development of compact fuel processor for 2 kW class residential PEMFCs

NASA Astrophysics Data System (ADS)

Seo, Yu Taek; Seo, Dong Joo; Jeong, Jin Hyeok; Yoon, Wang Lai

Korea Institute of Energy Research (KIER) has been developing a novel fuel processing system to provide hydrogen rich gas to residential polymer electrolyte membrane fuel cells (PEMFCs) cogeneration system. For the effective design of a compact hydrogen production system, the unit processes of steam reforming, high and low temperature water gas shift, steam generator and internal heat exchangers are thermally and physically integrated into a packaged hardware system. Several prototypes are under development and the prototype I fuel processor showed thermal efficiency of 73% as a HHV basis with methane conversion of 81%. Recently tested prototype II has been shown the improved performance of thermal efficiency of 76% with methane conversion of 83%. In both prototypes, two-stage PrOx reactors reduce CO concentration less than 10 ppm, which is the prerequisite CO limit condition of product gas for the PEMFCs stack. After confirming the initial performance of prototype I fuel processor, it is coupled with PEMFC single cell to test the durability and demonstrated that the fuel processor is operated for 3 days successfully without any failure of fuel cell voltage. Prototype II fuel processor also showed stable performance during the durability test.

Medicinal Plants from Northeastern Brazil against Alzheimer's Disease

PubMed Central

Ribeiro, Alan Bezerra; Alves, Daniela Ribeiro; Rodrigues, Ana Livya Moreira; dos Santos, Leonardo Hunaldo; de Menezes, Jane Eire Silva Alencar

2017-01-01

Alzheimer's disease (AD) has been linked with oxidative stress, acetylcholine deficiency in the brain, and inflammatory processes. In the northeast region of Brazil, various plants are used to treat several diseases associated with these processes; then an antioxidant test was performed with those plants in a previous work and twelve species with higher antioxidant activity were selected for AChE inhibition evaluation. The phenolic compounds content was determined by Folin–Ciocalteu test and flavonoid content with AlCl3 reagent using UV-visible spectrophotometry. The antioxidant activity was assessed analyzing the inhibitory activity against 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2-azinobis-3-ethylbenzothiazoline-6-sulfonate (ABTS) and by the β-carotene/linoleic acid system and acetylcholinesterase inhibition using qualitative and quantitative tests. The combination of better acetylcholinesterase inhibitory and antioxidant activities pointed out six species, in descending order, as the best potential sources of therapeutic agents against AD: Hancornia speciosa > Myracrodruon urundeuva > Copaifera langsdorffii > Stryphnodendron coriaceum > Psidium guajava > Mangifera indica. Besides, the phenolic compounds in the species probably contribute to these activities. However, further pharmacological studies to assess the specific applications of these plants against AD are required to confirm these results. PMID:28316633

Investigational Testing for Zika Virus among U.S. Blood Donors.

PubMed

Saá, Paula; Proctor, Melanie; Foster, Gregory; Krysztof, David; Winton, Colleen; Linnen, Jeffrey M; Gao, Kui; Brodsky, Jaye P; Limberger, Ronald J; Dodd, Roger Y; Stramer, Susan L

2018-05-10

Because of the potential severe clinical consequences of Zika virus (ZIKV) infection, the large numbers of asymptomatic travelers returning from ZIKV-active areas, the detection of ZIKV nucleic acid in blood, and reports of transmission of ZIKV through transfusion, in 2016 the Food and Drug Administration released recommendations for individual-unit nucleic acid testing to minimize the risk of transmission of ZIKV through blood transfusions. The American Red Cross implemented investigational screening of donated blood for ZIKV RNA by means of transcription-mediated amplification (TMA). Confirmatory testing of reactive donations involved repeat TMA, TMA testing in exploratory minipools, real-time reverse-transcriptase polymerase chain reaction, IgM serologic testing, and red-cell TMA. Viral loads in plasma and red cells were estimated by means of end-point TMA. The costs of interdicting a donation that was confirmed to be positive were calculated for the 15-month period between June 2016 and September 2017. Of the 4,325,889 donations that were screened, 393,713 (9%) were initially tested in 24,611 minipools, and no reactive donations were found. Of the 3,932,176 donations that were subsequently tested individually, 160 were initially reactive and 9 were confirmed positive (a 1:480,654 confirmed-positive rate overall; positive predictive value, 5.6%; specificity, 99.997%). Six (67%) of the confirmed-positive donations were reactive on repeat TMA, of which 4 were IgM-negative; of these 4, all 3 that could be tested were reactive on minipool TMA. Two confirmed-positive donors had infections that had been transmitted locally (in Florida), 6 had traveled to ZIKV-active areas, and 1 had received an experimental ZIKV vaccine. ZIKV RNA levels in red cells ranged from 40 to 800,000 copies per milliliter and were detected up to 154 days after donation, as compared with 80 days of detection in plasma at levels of 12 to 20,000 copies per milliliter. On the basis of industry-reported costs of testing and the yield of the tests in our study, the cost of identifying 8 mosquito-borne ZIKV infections through individual-unit nucleic acid testing was $5.3 million per ZIKV RNA-positive donation. Screening of U.S. blood donations for ZIKV by individual-donation TMA was costly and had a low yield. Among the 9 confirmed ZIKV-positive donations, only 4 were IgM-negative; of these donations, all 3 that were tested were reactive on minipool TMA. (Funded by the American Red Cross and Grifols Diagnostic Solutions.).

Episodic memory impairment in Addison's disease: results from a telephonic cognitive assessment.

PubMed

Henry, Michelle; Thomas, Kevin G F; Ross, Ian L

2014-06-01

Patients with Addison's disease frequently self-report memory and attention difficulties, even when on standard replacement therapy. However, few published studies examine, using objective measures and assessing across multiple domains, the cognitive functioning of Addison's disease patients relative to healthy controls. The primary aim of this study was to investigate whether the previously reported subjective cognitive deficits in Addison's disease are confirmed by objective measures. Conducting comprehensive neuropsychological assessments of patients with relatively rare clinical disorders, such as Addison's disease, is challenging because access to those patients is often limited, and because their medical condition might prevent extended testing sessions. Brief telephonic cognitive assessments are a useful tool in such circumstances. Hence, we administered the Brief Test of Adult Cognition by Telephone to 27 Addison's disease patients and 27 matched healthy controls. The instrument provides objective assessment of episodic memory, working memory, executive functioning, reasoning, and speed of processing. Statistical analyses confirmed that, as expected, patients performed significantly more poorly than controls on the episodic memory subtest. There were, however, no significant between-group differences on the attention, executive functioning, reasoning, and speed of processing subtests. Furthermore, patients with a longer duration of illness performed more poorly across all domains of cognition. We conclude that, for Addison's disease patients, previously reported subjective cognitive deficits are matched by objective impairment, but only in the domain of episodic memory. Future research might investigate (a) whether these memory deficits are material-specific (i.e., whether non-verbal memory is also affected), and (b) the neurobiological mechanisms underlying these deficits.

Lupus anticoagulant: a multicenter study for a standardized and harmonized reporting.

PubMed

Poz, Alessandra; Pradella, Paola; Azzarini, Gabriella; Santarossa, Liliana; Bardin, Cristina; Zardo, Lorena; Giacomello, Roberta

2016-03-01

Laboratory assessment of Lupus anticoagulant (LAC) is very challenging because of inter and intralaboratory variability, which makes it difficult to standardize and harmonize results expression. Five hospital laboratories in North-eastern Italy shared their efforts and their experience in a cross-laboratory study, conducting the diagnostic process as homogeneously as possible and providing a better interpretation for LAC positivity. Hundred normal samples from healthy subjects (20 from each center) were processed to confirm negative upper limits and calculate positivity cutoffs of LAC integrated assays, that is dilute Russell's viper venom time (dRVVT) and silica clotting time (SCT). Moreover, 311 samples previously diagnosed by the laboratories as positive for LAC were analyzed to characterize different positivity levels for each assay. As far as the analysis of healthy subjects is concerned, negative upper limits are set at 1.17 and 1.19 for dRVVT and SCT screen ratio, respectively. Positivity cutoffs are set at 1.20 for dRVVT and 1.23 for SCT, expressed as Test Ratio calculated on screen and confirm integrated tests. Positive results for each integrated assay are subsequently divided into three subgroups: weak, moderate and strong; the results obtained are presented as a score proposal that can provide LAC interpretation. The combined use of both dRVVT and SCT assays and the definition of different positivity levels may lead to clearer, more objective LAC reporting. An interpretative table for LAC-proposed score provides LAC-positive results and it is now adopted by all centers involved in the study.

Column Testing and 1D Reactive Transport Modeling to Evaluate Uranium Plume Persistence Processes

NASA Astrophysics Data System (ADS)

Johnson, R. H.; Morrison, S.; Morris, S.; Tigar, A.; Dam, W. L.; Dayvault, J.

2015-12-01

At many U.S. Department of Energy Office of Legacy Management sites, 100 year natural flushing was selected as a remedial option for groundwater uranium plumes. However, current data indicate that natural flushing is not occurring as quickly as expected and solid-phase and aqueous uranium concentrations are persistent. At the Grand Junction, Colorado office site, column testing was completed on core collected below an area where uranium mill tailings have been removed. The total uranium concentration in this core was 13.2 mg/kg and the column was flushed with laboratory-created water with no uranium and chemistry similar to the nearby Gunnison River. The core was flushed for a total of 91 pore volumes producing a maximum effluent uranium concentration of 6,110 μg/L at 2.1 pore volumes and a minimum uranium concentration of 36.2 μg/L at the final pore volume. These results indicate complex geochemical reactions at small pore volumes and a long tailing affect at greater pore volumes. Stop flow data indicate the occurrence of non-equilibrium processes that create uranium concentration rebound. These data confirm the potential for plume persistence, which is occurring at the field scale. 1D reactive transport modeling was completed using PHREEQC (geochemical model) and calibrated to the column test data manually and using PEST (inverse modeling calibration routine). Processes of sorption, dual porosity with diffusion, mineral dissolution, dispersion, and cation exchange were evaluated separately and in combination. The calibration results indicate that sorption and dual porosity are major processes in explaining the column test data. These processes are also supported by fission track photographs that show solid-phase uranium residing in less mobile pore spaces. These procedures provide valuable information on plume persistence and secondary source processes that may be used to better inform and evaluate remedial strategies, including natural flushing.

A Role of DLPFC in the Learning Process of Human Mate Copying

PubMed Central

Zhuang, Jin-Ying; Xie, Jiajia; Hu, Die; Fan, Mingxia; Zheng, Li

2016-01-01

In the current study, we conducted a behavioral experiment to test the mate coping effect and a functional magnetic resonance imaging (fMRI) experiment to test the neural basis involved in the social learning process of mate copying. In the behavioral experiment, participants were asked to rate the attractiveness of isolated opposite-sex (potential mates) facial photographs, then shown the targets associating with a neutral-faced model with textual cues indicating the models’ attitude (interested vs. not-interested) toward the potential mates, and then asked to re-evaluate the potential mates’ attractiveness. Using a similar procedure as the behavioral experiment, participants were scanned while observing the compound images in the fMRI experiment. The mate copying effect was confirmed in the behavioral experiment –greater increase in attractiveness ratings was observed for opposite-sex photographs in the interested than in the not-interested condition. The fMRI results showed that the dorsolateral prefrontal gyrus (DLPFC) was significantly active in the comparison of interested > not-interested condition, suggesting that a cognitive integration and selection function may be involved when participants process information from conditions related to mate copying. PMID:27148151

Can pore-clogging by ash explain post-fire runoff?

USGS Publications Warehouse

Stoof, Cathelijne R.; Gevaert, Anouk I.; Baver, Christine; Hassanpour, Bahareh; Morales, Veronica L.; Zhang, Wei; Martin, Deborah; Giri, Shree K.; Steenhuis, Tammo S.

2016-01-01

Ash plays an important role in controlling runoff and erosion processes after wildfire and has frequently been hypothesised to clog soil pores and reduce infiltration. Yet evidence for clogging is incomplete, as research has focussed on identifying the presence of ash in soil; the actual flow processes remain unknown. We conducted laboratory infiltration experiments coupled with microscope observations in pure sands, saturated hydraulic conductivity analysis, and interaction energy calculations, to test whether ash can clog pores (i.e. block pores such that infiltration is hampered and ponding occurs). Although results confirmed previous observations of ash washing into pores, clogging was not observed in the pure sands tested, nor were conditions found for which this does occur. Clogging by means of strong attachment of ash to sand was deemed unlikely given the negative surface charge of the two materials. Ponding due to washing in of ash was also considered improbable given the high saturated conductivity of pure ash and ash–sand mixtures. This first mechanistic step towards analysing ash transport and attachment processes in field soils therefore suggests that pore clogging by ash is unlikely to occur in sands. Discussion is provided on other mechanisms by which ash can affect post-fire hydrology.

[Vaccine for human immunodeficiency virus (HIV)--relevance of these days].

PubMed

Laiskonis, Alvydas; Pukenyte, Evelina

2005-01-01

Since 1980 more than 25 million people have died from acquired immunodeficiency syndrome (AIDS), which results from infection with human immunodeficiency virus (HIV). Number of new cases increases very threateningly. One and the most effective method to stop the progress of epidemic is the development of the vaccine for HIV. There is the presentation of the first stage of the vaccine for HIV testing (structure, methodology), which is now on trial in St. Pierre hospital, Brussels University. HIV characteristics which inflame the process of the vaccine development, historical facts and facts about vaccines on trial in these days are reviewed in this article. More than 10,000 volunteers have been participating in various clinical trials since 1987. The development of the vaccine is a very difficult, long-terming (about 8-10 years) and costly process. The process of the vaccine testing is very difficult in developing countries where the infection spreads the most rapidly. Available data confirm that the vaccine must be multi-componential, inducing cellular, humoral immunity against various subtypes of HIV. The vaccine cannot protect fully but the changes of the natural infection course could decrease virulence, distance the stage of AIDS, and retard the spread of the epidemic.

Fluidized bed gasification of industrial solid recovered fuels.

PubMed

Arena, Umberto; Di Gregorio, Fabrizio

2016-04-01

The study evaluates the technical feasibility of the fluidized bed gasification of three solid recovered fuels (SRFs), obtained as co-products of a recycling process. The SRFs were pelletized and fed to a pilot scale bubbling fluidized bed reactor, operated in gasification and co-gasification mode. The tests were carried out under conditions of thermal and chemical steady state, with a bed of olivine particles and at different values of equivalence ratio. The results provide a complete syngas characterization, in terms of its heating value and composition (including tars, particulates, and acid/basic pollutants) and of the chemical and physical characterization of bed material and entrained fines collected at the cyclone outlet. The feasibility of the fluidized bed gasification process of the different SRFs was evaluated with the support of a material and substance flow analysis, and a feedstock energy analysis. The results confirm the flexibility of fluidized bed reactor, which makes it one of the preferable technologies for the gasification of different kind of wastes, even in co-gasification mode. The fluidized bed gasification process of the tested SRFs appears technically feasible, yielding a syngas of valuable quality for energy applications in an appropriate plant configuration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

NASA Astrophysics Data System (ADS)

Chen, Fuh-Kuo; Chang, Chih-Kun

2005-08-01

In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures.

New Insights into the Role of Pb-BHA Complexes in the Flotation of Tungsten Minerals

NASA Astrophysics Data System (ADS)

Yue, Tong; Han, Haisheng; Hu, Yuehua; Sun, Wei; Li, Xiaodong; Liu, Runqing; Gao, Zhiyong; Wang, Li; Chen, Pan; Zhang, Chenyang; Tian, Mengjie

2017-11-01

Lead ions (lead nitrate) were introduced to modify the surface properties of tungsten minerals, effectively improving the floatability, with benzohydroxamic acid (BHA) serving as the collector. Flotation tests indicated that Pb-BHA complexes were the active species responsible for flotation of the tungsten minerals. The developed Pb-BHA complexes and the novel flotation process effectively increased the recovery of scheelite and wolframite, simplified the technological process, and led to reduced costs. Fourier transform infrared spectra data showed the presence of adsorbed Pb-BHA complexes on the surface of the minerals. The characteristic peaks of BHA shifted by a considerable extent, indicating that chemical adsorption plays an important role in the flotation process. Zeta potential results confirmed physical adsorption of the positively charged Pb-BHA complexes on the mineral surfaces. The synergistic effect between chemical and physical adsorption facilitated the maximum flotation recovery of scheelite and wolframite.

Robot-based additive manufacturing for flexible die-modelling in incremental sheet forming

NASA Astrophysics Data System (ADS)

Rieger, Michael; Störkle, Denis Daniel; Thyssen, Lars; Kuhlenkötter, Bernd

2017-10-01

The paper describes the application concept of additive manufactured dies to support the robot-based incremental sheet metal forming process (`Roboforming') for the production of sheet metal components in small batch sizes. Compared to the dieless kinematic-based generation of a shape by means of two cooperating industrial robots, the supporting robot models a die on the back of the metal sheet by using the robot-based fused layer manufacturing process (FLM). This tool chain is software-defined and preserves the high geometrical form flexibility of Roboforming while flexibly generating support structures adapted to the final part's geometry. Test series serve to confirm the feasibility of the concept by investigating the process challenges of the adhesion to the sheet surface and the general stability as well as the influence on the geometric accuracy compared to the well-known forming strategies.

Pushed aside: Parentheticals, Memory and Processing

PubMed Central

Dillon, Brian; Clifton, Charles; Frazier, Lyn

2014-01-01

In the current work, we test the hypothesis that ‘at-issue’ and 'not-at-issue' content (Potts, 2005) are processed semi-independently. In a written rating study comparing restrictive relative clauses and parentheticals in interrogatives and declaratives, we observe a significantly larger length penalty for restrictive relative clauses than for parentheticals. This difference cannot be attributed to differences in how listeners allocate attention across a sentence: a second study confirms that readers are equally sensitive to agreement violations in at-issue and not-at-issue content. A third rating experiment showed that the results do not depend on the restrictive relative clause intervening on the subject-verb dependency. A final experiment showed that the observed effects obtain with definite determiners and demonstratives alike. Taken jointly the results suggest that the parenthetical structures are processed independently of their embedding utterance, which in turn suggests that syntactic memory may be more differentiated than is typically assumed. PMID:24812639

[Assessment of a rapid diagnostic test and portable fluorescent microscopy for malaria diagnosis in Cotonou (Bénin)].

PubMed

Ogouyèmi-Hounto, A; Kinde-Gazard, D; Keke, C; Gonçalves, E; Alapini, N; Adjovi, F; Adisso, L; Bossou, C; Denon, Y V; Massougbodji, A

2013-02-01

The aim of the study was to determine the accuracy of a rapid diagnostic test (SD Bioline Malaria Ag P.f/ Pan®) and fluorescent microscopy (CyScope®) in confirming presumptive malaria diagnosis in Cotonou. Thick blood smear was used as the reference technique for comparison. Testing was conducted on persons between the ages of 6 months and 70 years at two hospitals from June to October 2010. If malaria was suspected in the sample by the nurse based on clinical findings and sent to laboratory for confirmation, one thick smear, one rapid diagnostic test and one slide for the fluorescent microscopy were performed. All tests were read in hospital laboratories involved with the quality control of thick blood smear in the parasitology laboratory of National University Hospital of Cotonou. A total of 354 patients with clinical diagnosis of malaria were included. Malaria prevalence determined by thick smear, rapid diagnostic test and fluorescent microscopy was 22.8%, 25.4%, and 25.1% respectively. The sensitivity, specificity, positive and negative predictive values compared to the thick smears were 96.3, 95.6, 86.7, and 98.9% for rapid diagnostic test; and 97.5, 96.7, 89.8, and 99.27% for fluorescent microscopy. With these performances, these tests meet acceptability standards recommended by WHO for rapid tests (sensitivity > 95%). These two methods have advantages for the confirmation of malaria diagnosis in peripheral health structures that lack the resources to conduct diagnosis confirmation by the thick blood smear.

Development of a new test for the easy characterization of the adhesion at the interface of bilayer tablets: proof-of-concept study by experimental design.

PubMed

Busignies, Virginie; Mazel, Vincent; Diarra, Harona; Tchoreloff, Pierre

2014-12-30

Although, adhesion at the interface of bilayer tablets is critical for their design it is difficult to characterize this adhesion between layers. In view of this, a new test with an easy implementation was proposed for the characterization of the interface of bilayer tablets. This work is presented as a proof-of-concept study to investigate the reliability of this new test with regard to the effects of some critical process parameters (e.g., compaction pressure applied on each layer) and material attributes (e.g., elasticity of the layered materials) on the interfacial adhesion of bilayer tablets. This was investigated using a design of experiment approach and the results obtained were in good accordance with those obtained with other tests and thus, confirms the potential of such a method for the measurement of the interfacial adhesion of bilayer tablets. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of desmopressin (DDAVP) on memory impairment following electroconvulsive therapy (ECT).

PubMed

Abdollahian, Ebrahim; Sargolzaee, Mohammad R; Hajzade, Moosareza; Mohebbi, Mohammad D; Javanbakht, Arash

2004-06-01

Memory impairment is a common adverse effect of electroconvulsive therapy (ECT). Studies on animals and humans suggest that vasopressin improves the cognitive function, and positive effects of desmopressin on memory and learning have been reported. This research was performed for evaluation of the effects of desmopressin in the prevention of memory impairment following ECT. This randomized, double-blind controlled clinical trial with placebo administration was performed on 50 patients with psychiatric disorders who were candidates for ECT. Subjects in the case group received 60 µm of intranasal desmopressin daily (in three doses of 20 µm). For the control group 0.9% saline solution was administered in the same way. Memory function was evaluated using Wechsler's Memory Scale three times a week (the first time before the start of ECT and the second and third times after the third and sixth sessions, respectively). Results were analyzed by t-test and Paired t-test. The mean age of patients was 29 years (range 20-40). During the course of ECT, patients in the control group demonstrated a meaningful decrease in memory scores (from a base score of 80.15-75.45 in the second test and 72.60 in the third test). Despite this, a meaningful increase in memory scores was observed during the treatment with desmopressin in the case group (from a base score of 73.27-75.70 and 79.13 in the second and the third tests, respectively). There was a meaningful difference between the two groups (P < 0.0001). This study confirms the protective effect of desmopressin against memory impairment. The results confirm that memory impairment is a common side-effect of ECT and suggest that desmopressin may prevent ECT-induced memory impairment by its effects on memory and the learning process.

Development of analysis technique to predict the material behavior of blowing agent

NASA Astrophysics Data System (ADS)

Hwang, Ji Hoon; Lee, Seonggi; Hwang, So Young; Kim, Naksoo

2014-11-01

In order to numerically simulate the foaming behavior of mastic sealer containing the blowing agent, a foaming and driving force model are needed which incorporate the foaming characteristics. Also, the elastic stress model is required to represent the material behavior of co-existing phase of liquid state and the cured polymer. It is important to determine the thermal properties such as thermal conductivity and specific heat because foaming behavior is heavily influenced by temperature change. In this study, three models are proposed to explain the foaming process and material behavior during and after the process. To obtain the material parameters in each model, following experiments and the numerical simulations are performed: thermal test, simple shear test and foaming test. The error functions are defined as differences between the experimental measurements and the numerical simulation results, and then the parameters are determined by minimizing the error functions. To ensure the validity of the obtained parameters, the confirmation simulation for each model is conducted by applying the determined parameters. The cross-verification is performed by measuring the foaming/shrinkage force. The results of cross-verification tended to follow the experimental results. Interestingly, it was possible to estimate the micro-deformation occurring in automobile roof surface by applying the proposed model to oven process analysis. The application of developed analysis technique will contribute to the design with minimized micro-deformation.

Failure to Confirm the Macrophage Electrophoretic Mobility Test in Cancer

PubMed Central

Forrester, J. A.; Dando, P. M.; Smith, W. J.; Turberville, C.

1977-01-01

A series of patients with a variety of histopathologically confirmed cancers have been examined using the MOD-MEM test as described by Pritchard et al. (1973). Despite the closest possible adherence to the experimental protocols recommended by these authors, no positive reactions to the test were observed in this series: neither were we able to demonstrate the release of a “macrophage-slowing factor” by a panel of normal donors when challenged with tubercle PPD. We conclude that the test has no present application to the diagnosis of cancer.

Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test.

PubMed

Pszczola, Marek; Jaczewski, Mariusz; Rys, Dawid; Jaskula, Piotr; Szydlowski, Cezary

2018-01-10

Low-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from -20 °C to +10 °C in order to evaluate the low-temperature performance of asphalt mixtures. Both validation of the method and its utilization for the assessment of eight types of wearing courses commonly used in Poland were described. The performed test indicated that the source of bitumen and its production process (and not necessarily only bitumen penetration) had a significant impact on the low-temperature performance of the asphalt mixtures, comparable to the impact of binder modification (neat, polymer-modified, highly modified) and the aggregate skeleton used in the mixture (Stone Mastic Asphalt (SMA) vs. Asphalt Concrete (AC)). Obtained Bending Beam Creep test results were compared with the BBR bitumen test. Regression analysis confirmed that performing solely bitumen tests is insufficient for comprehensive low-temperature performance analysis.

Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test

PubMed Central

Rys, Dawid; Jaskula, Piotr; Szydlowski, Cezary

2018-01-01

Low-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20 °C to +10 °C in order to evaluate the low-temperature performance of asphalt mixtures. Both validation of the method and its utilization for the assessment of eight types of wearing courses commonly used in Poland were described. The performed test indicated that the source of bitumen and its production process (and not necessarily only bitumen penetration) had a significant impact on the low-temperature performance of the asphalt mixtures, comparable to the impact of binder modification (neat, polymer-modified, highly modified) and the aggregate skeleton used in the mixture (Stone Mastic Asphalt (SMA) vs. Asphalt Concrete (AC)). Obtained Bending Beam Creep test results were compared with the BBR bitumen test. Regression analysis confirmed that performing solely bitumen tests is insufficient for comprehensive low-temperature performance analysis. PMID:29320443

Incentive memory: evidence the basolateral amygdala encodes and the insular cortex retrieves outcome values to guide choice between goal-directed actions.

PubMed

Parkes, Shauna L; Balleine, Bernard W

2013-05-15

Choice between goal-directed actions is determined by the relative value of their consequences. Such values are encoded during incentive learning and later retrieved to guide performance. Although the basolateral amygdala (BLA) and the gustatory region of insular cortex (IC) have been implicated in these processes, their relative contribution is still a matter of debate. Here we assessed whether these structures interact during incentive learning and retrieval to guide choice. In these experiments, rats were trained on two actions for distinct outcomes after which one of the two outcomes was devalued by specific satiety immediately before a choice extinction test. We first confirmed that, relative to appropriate controls, outcome devaluation recruited both the BLA and IC based on activation of the immediate early gene Arc; however, we found that infusion of the NMDAr antagonist ifenprodil into the BLA only abolished outcome devaluation when given before devaluation. In contrast, ifenprodil infusion into the IC was effective whether made before devaluation or test. We hypothesized that the BLA encodes and the IC retrieves incentive value for choice and, to test this, developed a novel sequential disconnection procedure. Blocking NMDAr activation unilaterally in the BLA before devaluation and then contralaterally in the IC before test abolished selective devaluation. In contrast, reversing the order of these infusions left devaluation intact. These results confirm that the BLA and IC form a circuit mediating the encoding and retrieval of outcome values, with the BLA encoding and the IC retrieving such values to guide choice.

SP-100 lithium thaw design, analysis, and testing

NASA Astrophysics Data System (ADS)

Choe, Hwang; Schrag, Michael R.; Koonce, David R.; Gamble, Robert E.; Halfen, Frank J.; Kirpich, Aaron S.

1993-01-01

The thaw design has been established for the 100 kWe SP-100 Space Reactor Power System. System thaw/startup analysis has confirmed that all system thaw requirements are met, and that rethaw and restart can be easily accomplished with this design. In addition, a series of lithium thaw characterization tests has been performed, confirming key design assumptions.

Application of the Capilia TB assay for culture confirmation of Mycobacterium tuberculosis complex isolates.

PubMed

Hillemann, D; Rüsch-Gerdes, S; Richter, E

2005-12-01

The usefulness of a low-tech rapid test for culture confirmation of Mycobacterium tuberculosis complex, Capilia TB, was tested on 172 mycobacteria-positive clinical samples. The overall sensitivity and specificity were 92.4% and 100%, respectively. In three of nine false-negative isolates a mutation in the mpb64 gene could be detected.

Discordant human T-lymphotropic virus screening with Western blot confirmation: evaluation of the dual-test algorithm for US blood donations.

PubMed

Stramer, Susan L; Townsend, Rebecca L; Foster, Gregory A; Johnson, Ramona; Weixlmann, Barbara; Dodd, Roger Y

2018-03-01

Human T-lymphotropic virus (HTLV) blood donation screening has used a dual-testing algorithm beginning with either a chemiluminescent immunoassay or enzyme-linked immunosorbent screening assay (ELISA). Before the availability of a licensed HTLV supplemental assay, repeat-reactive (RR) samples on a first assay (Assay 1) were retested with a second screening assay (Assay 2). Donors with RR results by Assay 2 were deferred from blood donation and further tested using an unlicensed supplemental test to confirm reactivity while nonreactive (NR) donors remained eligible for donation until RR on a subsequent donation. This "dual-test" algorithm was replaced in May 2016 with the requirement that all RRs by Assay 1 be further tested by a licensed HTLV supplemental test (Western blot [WB]). In this study, we have requalified the dual-test algorithm using the available licensed HTLV WB. We tested 100 randomly selected HTLV RRs on screening Assay 1 (Abbott PRISM chemiluminescent immunoassay) but NR on screening Assay 2 (Avioq ELISA) by a Food and Drug Administration-licensed WB (MP Biomedicals) to ensure that no confirmed positives were among those that were RR by Assay 1 but NR by Assay 2. Of the 100 samples evaluated, 79 of 100 were WB seronegative, 21 of 100 indeterminate, and 0 of 100 seropositive. Of the 79 of 100 seronegative specimens, 73 of 79 did not express any bands on WB. We demonstrated that none of the 100 samples RR on Assay 1 but NR on Assay 2 were confirmed positive. This algorithm prevents such donors from requiring further testing and from being deferred. © 2018 AABB.

Study of EPDM/PP polymeric blends: mechanical behavior and effects of compatibilization

NASA Astrophysics Data System (ADS)

Bouchart, Vanessa; Bhatnagar, N.; Brieu, Mathias; Ghosh, A. K.; Kondo, Djimedo

2008-09-01

A blend of Ethylene Propylene Diene Monomer (EPDM) rubber reinforced by polypropylene (PP) particles has been processed and its hyperelastic behavior has been characterized under cyclic uni-axial tensile tests. The experimental results show a significant effect of the fraction of polypropylene particles (10%, 25% and 30% by weight). Moreover, from another series of tests conducted on materials containing compatibilizers at different mass concentration, it is observed that the introduction of a compatibilizer increases the rigidity of the blends and affects notably their macroscopic behavior. These observations are interpreted as a consequence of the modification at microlevel of adherence between particles and matrix phases. The use of a nonlinear micromechanical model allows us to confirm this interpretation. To cite this article: V. Bouchart et al., C. R. Mecanique 336 (2008).

Actual curriculum development practices instrument: Testing for factorial validity

NASA Astrophysics Data System (ADS)

Foi, Liew Yon; Bakar, Kamariah Abu; Hamzah, Mohd Sahandri Gani; Alwi, Nor Hayati

2014-09-01

The Actual Curriculum Development Practices Instrument (ACDP-I) was developed and the factorial validity of the ACDP-I was tested (n = 107) using exploratory factor analysis procedures in the earlier work of [1]. Despite the ACDP-I appears to be content and construct valid instrument with very high internal reliability qualities for using in Malaysia, the accumulated evidences are still needed to provide a sound scientific basis for the proposed score interpretations. Therefore, the present study addresses this concern by utilising the confirmatory factor analysis to further confirm the theoretical structure of the variable Actual Curriculum Development Practices (ACDP) and enrich the psychometrical properties of ACDP-I. Results of this study have practical implication to both researchers and educators whose concerns focus on teachers' classroom practices and the instrument development and validation process.

Materialists on Facebook: the self-regulatory role of social comparisons and the objectification of Facebook friends.

PubMed

Ozimek, Phillip; Baer, Fiona; Förster, Jens

2017-11-01

In this study, we examine chronic materialism as a possible motive for Facebook usage. We test an explanatory mediation model predicting that materialists use Facebook more frequently, because they compare themselves to others, they objectify and instrumentalize others, and they accumulate friends. For this, we conducted two online surveys ( N 1 = 242, N 2 = 289) assessing demographic variables, Facebook use, social comparison, materialism, objectification and instrumentalization. Results confirm the predicted mediation model. Our findings suggest that Facebook can be used as a means to an end in a way of self-regulatory processes, like satisfying of materialistic goals. The findings are the first evidence for our Social Online Self-regulation Theory (SOS-T), which contains numerous predictions that can be tested in the future.

[Epidemiologic-anamnestic study of stomach cancer in relation to nutrition].

PubMed

Jarebinski, M; Adanja, B; Vlajinac, H; Sipetić, S; Pekmezović, T; Pantović, V

1994-01-01

Correlation between the disease and nutritional habits was evaluated in this epidemiologic-anamnestic study. It included 80 patients with the confirmed diagnosis of stomach cancer and the same number of controls selected from five hospitals in Belgrade. Both groups were matched by the sex, age and living place. McNemar's test was used for testing differences in exposure to the hypothetic factors. Based on the analysis of various food intake frequency it could be concluded that nutrition of patients with stomach cancer was, in comparison with the one taken by the control group, poorer in animal proteins, vegetables and citrus fruits, and rich in cereals processed in the form of various pastas and sweets, delicatessen, canned food as well as fruit rich in unsaturated fatty acids (nuts).

A quinoline-based fluorometric and colorimetric dual-modal pH probe and its application in bioimaging

NASA Astrophysics Data System (ADS)

Zhu, Qin; Li, Zhao; Mu, Lan; Zeng, Xi; Redshaw, Carl; Wei, Gang

2018-01-01

The compound (E)-8-hydroxyl-2-[(E)-2-(2, 4-dihydroxyphenyl)vinyl]-quinoline (1) has been developed as a fluorometric and colorimetric dual-modal probe for pH detection in solution and in vivo. Remarkable changes in the fluorescence intensity with large Stokes shifts and colorimetric responses were observed as a function of pH. The sensing mechanisms involving protonation and deprotonation processes over the acidic and alkaline pH ranges were confirmed by 1H NMR and IR spectroscopic analysis. Furthermore, the application of probe 1 for the imaging of live PC3 cells was successfully achieved. Test strips based on probe 1 were fabricated, and were found to act as a convenient and efficient pH test kits.

Testing the Merger Paradigm: X-ray Observations of Radio-Selected Sub-Galactic-Scale Binary AGNs

NASA Astrophysics Data System (ADS)

Fu, Hai

2016-09-01

Interactions play an important role in galaxy evolution. Strong gas inflows are expected in the process of gas-rich mergers, which may fuel intense black hole accretion and star formation. Sub-galactic-scale binary/dual AGNs thus offer elegant laboratories to study the merger-driven co-evolution phase. However, previous samples of kpc-scale binaries are small and heterogeneous. We have identified a flux-limited sample of kpc-scale binary AGNs uniformly from a wide-area high-resolution radio survey conducted by the VLA. Here we propose Chandra X-ray characterization of a subset of four radio-confirmed binary AGNs at z 0.1. Our goal is to compare their X-ray properties with those of matched control samples to test the merger-driven co-evolution paradigm.

Incorporation of Tin on copper clad laminate to increase the interface adhesion for signal loss reduction of high-frequency PCB lamination

NASA Astrophysics Data System (ADS)

Wang, Chong; Wen, Na; Zhou, Guoyun; Wang, Shouxu; He, Wei; Su, Xinhong; Hu, Yongsuan

2017-11-01

A novel method of improving the adhesion between copper and prepreg in high frequency PCB was proposed and studied in this work. This process which aimed to decrease the IEP (isoelectric point) of the copper to obtain higher adhesion, was achieved by depositing a thin tin layer with lower IEP on copper. It was characterized by scanning electron microscopy (SEM), 3D microscope, peel strength test, X-Ray thickness test, grazing incidence X-ray diffraction (GXRD), X-ray photoelectron spectroscopy (XPS), Agilent vector network analyzer (VNA), which confirmed its excellent adhesion performance and outstanding electrical properties in high-frequency signal transmission compared with traditional brown oxide method. Moreover, the mechanism of achieving high adhesion for this method was also investigated.

[Radionuclide evaluation of the mucociliary function of the mucosa of the nasal cavity in chronic lung diseases].

PubMed

Kasatkin, Iu N; Kaganov, S Iu; Vyrenkova, N Iu; Kramer, E F; Rozinova, N N

1987-02-01

The authors presented their first experience of radionuclide assessment of the nasal mucosal transport (NMT) in 39 patients with chronic bronchopulmonary pathology (14 adults and 25 children) to detect patients among them with suspected syndrome of primary ciliary dyskinesia (SPCD). In 18 patients the test was positive excluding SPCD as a cause of a chronic inflammatory pulmonary process. In 21 patients NMT was absent, 2 of these patients had Kartagener's triad serving as a kind of model confirming the data on NMT. The authors proposed the method as a screening test due to its non-invasiveness and simplicity in patients with chronic inflammatory pulmonary diseases in order to detect among them patients with suspected SPCD for further examination using invasive methods.

Strategies for Maximizing Successful Drug Substance Technology Transfer Using Engineering, Shake-Down, and Wet Test Runs.

PubMed

Abraham, Sushil; Bain, David; Bowers, John; Larivee, Victor; Leira, Francisco; Xie, Jasmina

2015-01-01

The technology transfer of biological products is a complex process requiring control of multiple unit operations and parameters to ensure product quality and process performance. To achieve product commercialization, the technology transfer sending unit must successfully transfer knowledge about both the product and the process to the receiving unit. A key strategy for maximizing successful scale-up and transfer efforts is the effective use of engineering and shake-down runs to confirm operational performance and product quality prior to embarking on good manufacturing practice runs such as process performance qualification runs. We consider key factors to consider in making the decision to perform shake-down or engineering runs. We also present industry benchmarking results of how engineering runs are used in drug substance technology transfers alongside the main themes and best practices that have emerged. Our goal is to provide companies with a framework for ensuring the "right first time" technology transfers with effective deployment of resources within increasingly aggressive timeline constraints. © PDA, Inc. 2015.

Fabrication of high quality carbonaceous coating on Cu nanoparticle using poly(vinyl pyrrolidone) and its application for oxidation prevention

NASA Astrophysics Data System (ADS)

Pyo, Youngjun; Choi, Dahyun; Son, Yeon-Ho; Kang, Suhee; Yoon, Eric H.; Jung, Seung-Boo; Kim, Yongil; Sunyong Lee, Caroline

2016-05-01

A novel method of carbonaceous coating on the surface of copper particles was developed through a chemical vapor deposition (CVD) process to prevent the oxidation of copper nanoparticles (CNPs). The types of poly(vinyl pyrrolidone) (PVP) used were K-12 (M W 3,500) and K-30 (M W 45,000). The amounts of PVP used ranged from 10 to 50 wt %. Additionally, processing temperatures of 900 and 875 °C were tested and compared. The optimum CVD process conditions for the carbonaceous coating were as follows: 875 °C processing temperature, 50 wt % K12 PVP solution, and gas conditions of \\text{Ar}:\\text{H}2 = 1:1. The resistivity change in the fabricated copper pattern was confirmed that the initial resistivity value of the ink with a mixing ratio of carbonaceous-coated CNPs to 1-octanethiol-coated CNPs of 4:6 (w/w) maintained its initial resistivity value of 2.93 × 10-7 Ω·m for more than 210 days.

The use of the Novosol process for the treatment of polluted marine sediment.

PubMed

Zoubeir, Lafhaj; Adeline, Saliceto; Laurent, Cohen Solal; Yoann, Coudray; Truc, Huynh Trung; Benoît, Le Guen; Federico, Anguoni

2007-09-30

The work presented in this article concerns polluted marine sediments. The article is divided into three parts. The first part discusses existing industrial procedures of treatment. The second part introduces the Novosol((R)) process, which was used for the treatment of polluted marine sediments. This process is based on the stabilization of heavy metals in the solid matrix by phosphatation and the destruction of organic matter by calcination. Finally, after a comparison had been made between environmental results obtained on both polluted marine sediments and inert ones, treated sediments were introduced in the production of clay bricks. The results obtained show that the Novosol process leads to the immobilization of most heavy metals and can be considered as an efficient tool for the stabilisation of polluted marine sediment. Thus, the results of physical and mechanical tests as compressive strength and water absorption indicate that performances obtained were comparable to standard brick values. These results confirm that, once treated, polluted sediments can be recycled.

Cognitive spare capacity: evaluation data and its association with comprehension of dynamic conversations

PubMed Central

Keidser, Gitte; Best, Virginia; Freeston, Katrina; Boyce, Alexandra

2015-01-01

It is well-established that communication involves the working memory system, which becomes increasingly engaged in understanding speech as the input signal degrades. The more resources allocated to recovering a degraded input signal, the fewer resources, referred to as cognitive spare capacity (CSC), remain for higher-level processing of speech. Using simulated natural listening environments, the aims of this paper were to (1) evaluate an English version of a recently introduced auditory test to measure CSC that targets the updating process of the executive function, (2) investigate if the test predicts speech comprehension better than the reading span test (RST) commonly used to measure working memory capacity, and (3) determine if the test is sensitive to increasing the number of attended locations during listening. In Experiment I, the CSC test was presented using a male and a female talker, in quiet and in spatially separated babble- and cafeteria-noises, in an audio-only and in an audio-visual mode. Data collected on 21 listeners with normal and impaired hearing confirmed that the English version of the CSC test is sensitive to population group, noise condition, and clarity of speech, but not presentation modality. In Experiment II, performance by 27 normal-hearing listeners on a novel speech comprehension test presented in noise was significantly associated with working memory capacity, but not with CSC. Moreover, this group showed no significant difference in CSC as the number of talker locations in the test increased. There was no consistent association between the CSC test and the RST. It is recommended that future studies investigate the psychometric properties of the CSC test, and examine its sensitivity to the complexity of the listening environment in participants with both normal and impaired hearing. PMID:25999904

Application of off-line image processing for optimization in chest computed radiography using a low cost system.

PubMed

Muhogora, Wilbroad E; Msaki, Peter; Padovani, Renato

2015-03-08

 The objective of this study was to improve the visibility of anatomical details by applying off-line postimage processing in chest computed radiography (CR). Four spatial domain-based external image processing techniques were developed by using MATLAB software version 7.0.0.19920 (R14) and image processing tools. The developed techniques were implemented to sample images and their visual appearances confirmed by two consultant radiologists to be clinically adequate. The techniques were then applied to 200 chest clinical images and randomized with other 100 images previously processed online. These 300 images were presented to three experienced radiologists for image quality assessment using standard quality criteria. The mean and ranges of the average scores for three radiologists were characterized for each of the developed technique and imaging system. The Mann-Whitney U-test was used to test the difference of details visibility between the images processed using each of the developed techniques and the corresponding images processed using default algorithms. The results show that the visibility of anatomical features improved significantly (0.005 ≤ p ≤ 0.02) with combinations of intensity values adjustment and/or spatial linear filtering techniques for images acquired using 60 ≤ kVp ≤ 70. However, there was no improvement for images acquired using 102 ≤ kVp ≤ 107 (0.127 ≤ p ≤ 0.48). In conclusion, the use of external image processing for optimization can be effective in chest CR, but should be implemented in consultations with the radiologists.

Application of off‐line image processing for optimization in chest computed radiography using a low cost system

PubMed Central

Msaki, Peter; Padovani, Renato

2015-01-01

The objective of this study was to improve the visibility of anatomical details by applying off‐line postimage processing in chest computed radiography (CR). Four spatial domain‐based external image processing techniques were developed by using MATLAB software version 7.0.0.19920 (R14) and image processing tools. The developed techniques were implemented to sample images and their visual appearances confirmed by two consultant radiologists to be clinically adequate. The techniques were then applied to 200 chest clinical images and randomized with other 100 images previously processed online. These 300 images were presented to three experienced radiologists for image quality assessment using standard quality criteria. The mean and ranges of the average scores for three radiologists were characterized for each of the developed technique and imaging system. The Mann‐Whitney U‐test was used to test the difference of details visibility between the images processed using each of the developed techniques and the corresponding images processed using default algorithms. The results show that the visibility of anatomical features improved significantly (0.005≤p≤0.02) with combinations of intensity values adjustment and/or spatial linear filtering techniques for images acquired using 60≤kVp≤70. However, there was no improvement for images acquired using 102≤kVp≤107 (0.127≤p≤0.48). In conclusion, the use of external image processing for optimization can be effective in chest CR, but should be implemented in consultations with the radiologists. PACS number: 87.59.−e, 87.59.−B, 87.59.−bd PMID:26103165

Geocoding uncertainty analysis for the automated processing of Sentinel-1 data using Sentinel-1 Toolbox software

NASA Astrophysics Data System (ADS)

Dostálová, Alena; Naeimi, Vahid; Wagner, Wolfgang; Elefante, Stefano; Cao, Senmao; Persson, Henrik

2016-10-01

One of the major advantages of the Sentinel-1 data is its capability to provide very high spatio-temporal coverage allowing the mapping of large areas as well as creation of dense time-series of the Sentinel-1 acquisitions. The SGRT software developed at TU Wien aims at automated processing of Sentinel-1 data for global and regional products. The first step of the processing consists of the Sentinel-1 data geocoding with the help of S1TBX software and their resampling to a common grid. These resampled images serve as an input for the product derivation. Thus, it is very important to select the most reliable processing settings and assess the geocoding uncertainty for both backscatter and projected local incidence angle images. Within this study, selection of Sentinel-1 acquisitions over 3 test areas in Europe were processed manually in the S1TBX software, testing multiple software versions, processing settings and digital elevation models (DEM) and the accuracy of the resulting geocoded images were assessed. Secondly, all available Sentinel-1 data over the areas were processed using selected settings and detailed quality check was performed. Overall, strong influence of the used DEM on the geocoding quality was confirmed with differences up to 80 meters in areas with higher terrain variations. In flat areas, the geocoding accuracy of backscatter images was overall good, with observed shifts between 0 and 30m. Larger systematic shifts were identified in case of projected local incidence angle images. These results encourage the automated processing of large volumes of Sentinel-1 data.

Sensitivity and specificity of a urinary screening test used in an emergency setting to detect abnormal first trimester pregnancies.

PubMed

Teixeira, João L G; Rabaioli, Paola; Savaris, Ricardo F

2015-01-01

To evaluate the performance of a commercial urinary test to screen for abnormal first trimester pregnancies in women presenting to an emergency room. In this prospective observational cohort, women with a confirmed first trimester pregnancy (gestational age <12 weeks) provided a urine sample for diagnosing the viability of their gestation. Pregnancy viability and location testing were confirmed by ultrasound and/or laparoscopy. From 815 eligible patients for the study, 12 were excluded for not having a confirmed pregnancy (n = 6) or were lost to follow-up (n = 6). A total of 803 patients underwent testing and completed follow-up. The pretest probability of an abnormal pregnancy was 44% (9% for ectopic pregnancy and 35% for miscarriage). The test had the following parameters to identify an abnormal first-trimester pregnancy (sensitivity, 13%; 95% confidence interval [CI], 10-17; specificity, 82%; 95% CI, 78-86; positive predictive value, 36; 95% CI, 28-46; negative predictive value, 54; 95% CI, 50-58; accuracy, 47%; positive likelihood ratio, 0.74; 95% CI, 0.53-1.03; negative likelihood ratio, 1.06; 95% CI, 1-1.12). The reproducibility of the test in our study was high (kappa index between readers, 0.89; 95% CI, 0.77-1). In our emergency setting, we were not able to confirm that the commercial test is adequate to detect or exclude an abnormal first-trimester pregnancy. Copyright © 2015 Elsevier Inc. All rights reserved.

Myositis-specific autoantibodies are specific for myositis compared to genetic muscle disease.

PubMed

Mammen, Andrew L; Casciola-Rosen, Livia; Christopher-Stine, Lisa; Lloyd, Thomas E; Wagner, Kathryn R

2015-12-01

To determine the specificity of myositis-specific autoantibodies (MSAs) for autoimmune myopathy compared with inherited muscle diseases. Serum samples from 47 patients with genetically confirmed inherited muscle diseases were screened for the most common MSAs, including those recognizing TIF1γ, NXP2, Mi2, MDA5, Jo1, SRP, and HMGCR. We compared these results with the findings in a cohort of patients with dermatomyositis (DM) previously screened for anti-TIF1γ, -NXP2, -Mi2, -MDA5, and -Jo1. Overall, the presence of anti-TIF1γ, -NXP2, -Mi2, -MDA5, or -Jo1 was 96% specific and 67% sensitive for DM compared to patients with genetic muscle diseases. No patients with inherited muscle disease had anti-SRP or anti-HMGCR autoantibodies. Only 2 patients with genetic muscle disease had a MSA. One patient with anti-Mi2 autoantibodies had both genetically confirmed facioscapulohumeral dystrophy and dermatomyositis based on a typical skin rash and partial response to immunosuppressive medications. A second patient with anti-Jo-1 autoantibodies had both genetically defined limb-girdle muscular dystrophy type 2A (i.e., calpainopathy) and a systemic autoimmune process based on biopsy-confirmed lupus nephritis, sicca symptoms, and anti-Ro52 autoantibodies. The MSAs tested for in this study are highly specific for autoimmune muscle disease and are rarely, if ever, found in patients who only have genetic muscle disease. In patients with genetic muscle disease, the presence of a MSA should suggest the possibility of a coexisting autoimmune process.

Myositis-specific autoantibodies are specific for myositis compared to genetic muscle disease

PubMed Central

Casciola-Rosen, Livia; Christopher-Stine, Lisa; Lloyd, Thomas E.; Wagner, Kathryn R.

2015-01-01

Objective: To determine the specificity of myositis-specific autoantibodies (MSAs) for autoimmune myopathy compared with inherited muscle diseases. Methods: Serum samples from 47 patients with genetically confirmed inherited muscle diseases were screened for the most common MSAs, including those recognizing TIF1γ, NXP2, Mi2, MDA5, Jo1, SRP, and HMGCR. We compared these results with the findings in a cohort of patients with dermatomyositis (DM) previously screened for anti-TIF1γ, -NXP2, -Mi2, -MDA5, and -Jo1. Results: Overall, the presence of anti-TIF1γ, -NXP2, -Mi2, -MDA5, or -Jo1 was 96% specific and 67% sensitive for DM compared to patients with genetic muscle diseases. No patients with inherited muscle disease had anti-SRP or anti-HMGCR autoantibodies. Only 2 patients with genetic muscle disease had a MSA. One patient with anti-Mi2 autoantibodies had both genetically confirmed facioscapulohumeral dystrophy and dermatomyositis based on a typical skin rash and partial response to immunosuppressive medications. A second patient with anti-Jo-1 autoantibodies had both genetically defined limb-girdle muscular dystrophy type 2A (i.e., calpainopathy) and a systemic autoimmune process based on biopsy-confirmed lupus nephritis, sicca symptoms, and anti-Ro52 autoantibodies. Conclusions: The MSAs tested for in this study are highly specific for autoimmune muscle disease and are rarely, if ever, found in patients who only have genetic muscle disease. In patients with genetic muscle disease, the presence of a MSA should suggest the possibility of a coexisting autoimmune process. PMID:26668818

Sweat electrolytes test

MedlinePlus

... test is used to confirm these results. Normal Results Normal results include: A sweat chloride test result ... edema) can affect the test results. What Abnormal Results Mean An abnormal test may mean that the ...

Serotonin depletion induces pessimistic-like behavior in a cognitive bias paradigm in pigs.

PubMed

Stracke, Jenny; Otten, Winfried; Tuchscherer, Armin; Puppe, Birger; Düpjan, Sandra

2017-05-15

Cognitive and affective processes are highly interrelated. This has implications for neuropsychiatric disorders such as major depressive disorder in humans but also for the welfare of non-human animals. The brain serotonergic system might play a key role in mediating the relationship between cognitive functions and affective regulation. The aim of our study was to examine the influence of serotonin depletion on the affective state and cognitive processing in pigs, an important farm animal species but also a potential model species for biomedical research in humans. For this purpose, we modified a serotonin depletion model using para-chlorophenylalanine (pCPA) to decrease serotonin levels in brain areas involved in cognitive and affective processing (part 1). The consequences of serotonin depletion were then measured in two behavioral tests (part 2): the spatial judgement task (SJT), providing information about the effects of the affective state on cognitive processing, and the open field/novel object (OFNO) test, which measures behavioral reactions to novelty that are assumed to reflect affective state. In part 1, 40 pigs were treated with either pCPA or saline for six consecutive days. Serotonin levels were assessed in seven different brain regions 4, 5, 6, 11 and 13days after the first injection. Serotonin was significantly depleted in all analyzed brain regions up to 13days after the first application. In part 2, the pCPA model was applied to 48 animals in behavioral testing. Behavioral tests, the OFNO test and the SJT, were conducted both before and after pCPA/saline injections. While results from the OFNO tests were inconclusive, an effect of treatment as well as an effect of the phase (before and after treatment) was observed in the SJT. Animals treated with pCPA showed more pessimistic-like behavior, suggesting a more negative affective state due to serotonin depletion. Thus, our results confirm that the serotonergic system is a key player in cognitive-emotional processing. Hence, the serotonin depletion model and the spatial judgement task can increase our understanding of the basic mechanisms underlying both human neuropsychiatric disorders and animal welfare. Copyright © 2017 Elsevier Inc. All rights reserved.

Ceria modified activated carbon: an efficient arsenic removal adsorbent for drinking water purification

NASA Astrophysics Data System (ADS)

Sawana, Radha; Somasundar, Yogesh; Iyer, Venkatesh Shankar; Baruwati, Babita

2017-06-01

Ceria (CeO2) coated powdered activated carbon was synthesized by a single step chemical process and demonstrated to be a highly efficient adsorbent for the removal of both As(III) and As(V) from water without any pre-oxidation process. The formation of CeO2 on the surface of powdered activated carbon was confirmed by X-ray diffraction, Raman spectroscopy and X-ray photoelectron spectroscopy. The percentage of Ce in the adsorbent was confirmed to be 3.5 % by ICP-OES. The maximum removal capacity for As(III) and As(V) was found to be 10.3 and 12.2 mg/g, respectively. These values are comparable to most of the commercially available adsorbents. 80 % of the removal process was completed within 15 min of contact time in a batch process. More than 95 % removal of both As(III) and As(V) was achieved within an hour. The efficiency of removal was not affected by change in pH (5-9), salinity, hardness, organic (1-4 ppm of humic acid) and inorganic anions (sulphate, nitrate, chloride, bicarbonate and fluoride) excluding phosphate. Presence of 100 ppm phosphate reduced the removal significantly from 90 to 18 %. The equilibrium adsorption pattern of both As(III) and As(V) fitted well with the Freundlich model with R 2 values 0.99 and 0.97, respectively. The material shows reusability greater than three times in a batch process (arsenic concentration reduced below 10 ppb from 330 ppb) and a life of at least 100 L in a column study with 80 g material when tested under natural hard water (TDS 1000 ppm, pH 7.8, hardness 600 ppm as CaCO3) spiked with 330 ppb of arsenic.

Assessing Saudi medical students learning approach using the revised two-factor study process questionnaire.

PubMed

Shaik, Shaffi Ahamed; Almarzuqi, Ahmed; Almogheer, Rakan; Alharbi, Omar; Jalal, Abdulaziz; Alorainy, Majed

2017-08-17

To assess learning approaches of 1st, 2nd, and 3rd-year medical students by using revised two-factor study process questionnaire, and to assess reliability and validity of the questionnaire. This cross-sectional study was conducted at the College of Medicine, Riyadh, Saudi Arabia in 2014. The revised two-factor study process questionnaire (R-SPQ-2F) was completed by 610 medical students of both genders, from foundation (first year), central nervous system (second year), medicine and surgery (third year) courses. The study process was evaluated by computing mean scores of two research study approaches (deep & surface) using student's t-test and one-way analysis of variance. The internal consistency and construct validity of the questionnaire were assessed using Cronbach's α and factor analysis. The mean score of deep approach was significantly higher than the surface approach among participants(t (770) =7.83, p= 0.000) for the four courses. The mean scores of deep approach were significantly higher among participants with higher grade point average (F (2,768) =13.31, p=0.001) along with more number of study hours by participants (F (2,768) =20.08, p=0.001). The Cronbach's α-values of items at 0.70 indicate the good internal consistency of questionnaire used. Factor analysis confirms two factors (deep and surface approaches) of R-SPQ-2F. The deep approach to learning was the primary approach among 1st, 2nd and 3rd-year King Saud University medical students. This study confirms reliability and validity of the revised two-factor study process questionnaire. Medical educators could use the results of such studies to make required changes in the curriculum.

An experimental design approach to the preparation of pegylated polylactide-co-glicolide gentamicin loaded microparticles for local antibiotic delivery.

PubMed

Dorati, Rossella; DeTrizio, Antonella; Genta, Ida; Grisoli, Pietro; Merelli, Alessia; Tomasi, Corrado; Conti, Bice

2016-01-01

The present paper takes into account the DOE application to the preparation process of biodegradable microspheres for osteomyelitis local therapy. With this goal gentamicin loaded polylactide-co-glycolide-copolyethyleneglycol (PLGA-PEG) microspheres were prepared and investigated. Two preparation protocols (o/w and w/o/w) with different process conditions, and three PLGA-PEG block copolymers with different compositions of lactic and glycolic acids and PEG, were tested. A Design Of Experiment (DOE) screening design was applied as an approach to scale up manufacturing step. The results of DOE screening design confirmed that w/o/w technique, the presence of salt and the 15%w/v polymer concentration positively affected the EE% (72.1-97.5%), and span values of particle size distribution (1.03-1.23), while salt addition alone negatively affected the yield process. Process scale up resulted in a decrease of gentamicin EE% that can be attributed to the high volume of water used to remove PVA and NaCl residues. The results of in vitro gentamicin release study show prolonged gentamicin release up to three months from the microspheres prepared with salt addition in the dispersing phase; the behavior being consistent with their highly compact structure highlighted by scanning electron microscopy analysis. The prolonged release of gentamicin is maintained even after embedding the biodegradable microspheres into a thermosetting composite gel made of chitosan and acellular bovine bone matrix (Orthoss® granules), and the microbiologic evaluation demonstrated the efficacy of the gentamicin loaded microspheres on Escherichia coli. The collected results confirm the feasibility of the scale up of microsphere manufacturing process and the high potential of the microparticulate drug delivery system to be used for the local antibiotic delivery to bone.

Edge-illumination x-ray phase contrast imaging with Pt-based metallic glass masks

NASA Astrophysics Data System (ADS)

Saghamanesh, Somayeh; Aghamiri, Seyed Mahmoud-Reza; Olivo, Alessandro; Sadeghilarijani, Maryam; Kato, Hidemi; Kamali-Asl, Alireza; Yashiro, Wataru

2017-06-01

Edge-illumination x-ray phase contrast imaging (EI XPCI) is a non-interferometric phase-sensitive method where two absorption masks are employed. These masks are fabricated through a photolithography process followed by electroplating which is challenging in terms of yield as well as time- and cost-effectiveness. We report on the first implementation of EI XPCI with Pt-based metallic glass masks fabricated by an imprinting method. The new tested alloy exhibits good characteristics including high workability beside high x-ray attenuation. The fabrication process is easy and cheap, and can produce large-size masks for high x-ray energies within minutes. Imaging experiments show a good quality phase image, which confirms the potential of these masks to make the EI XPCI technique widely available and affordable.

Dissolution of Oxygen Precipitate Nuclei in n-Type CZ-Si Wafers to Improve Their Material Quality: Experimental Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sopori, Bhushan; Basnyat, Prakash; Devayajanam, Srinivas

2017-01-01

We present experimental results which show that oxygen-related precipitate nuclei (OPN) present in p-doped, n-type, Czochralski wafers can be dissolved using a flash-annealing process, yielding very high quality wafers for high-efficiency solar cells. Flash annealing consists of heating a wafer in an optical furnace to temperature between 1150 and 1250 degrees C for a short time. This process produces a large increase in the minority carrier lifetime (MCLT) and homogenizes each wafer. We have tested wafers from different axial locations of two ingots. All wafers reach nearly the same high value of MCLT. The OPN dissolution is confirmed by oxygenmore » analysis using Fourier transform infrared spectra and injection-level dependence of MCLT.« less

Cleaner production in the ammonia-soda industry: an ecological and economic study.

PubMed

Kasikowski, T; Buczkowski, R; Lemanowska, E

2004-12-01

Five methods to reduce the negative influence of soda ash factories on the natural environment are presented: 1. obtaining calcium-magnesium phosphates by treating the suspension from raw brine purification with orthophosphoric acid (H(3)PO(4)), 2. production of precipitated chalk from soda processing waste, 3. production of gypsum and semi-brine, 4. desulphurisation of fume gases from the factory power plant, 5. utilization of distiller waste. The tests, accomplished on a laboratory scale, showed the high efficiency of these methods. Economic analysis has proved that only four out of the five presented processes can have a positive financial effect on soda ash factories, as well as being well justified economically. The value of two of the innovations presented is confirmed by their implementation in factories.

Design of a smart ECG garment based on conductive textile electrode and flexible printed circuit board.

PubMed

Cai, Zhipeng; Luo, Kan; Liu, Chengyu; Li, Jianqing

2017-08-09

A smart electrocardiogram (ECG) garment system was designed for continuous, non-invasive and comfortable ECG monitoring, which mainly consists of four components: Conductive textile electrode, garment, flexible printed circuit board (FPCB)-based ECG processing module and android application program. Conductive textile electrode and FPCB-based ECG processing module (6.8 g, 55 mm × 53 mm × 5 mm) are identified as two key techniques to improve the system's comfort and flexibility. Preliminary experimental results verified that the textile electrodes with circle shape, 40 mm size in diameter, and 5 mm thickness sponge are best suited for the long-term ECG monitoring application. The tests on the whole system confirmed that the designed smart garment can obtain long-term ECG recordings with high signal quality.

Occupational Decision-Related Processes for Amotivated Adolescents: Confirmation of a Model

ERIC Educational Resources Information Center

Jung, Jae Yup; McCormick, John

2011-01-01

This study developed and (statistically) confirmed a new model of the occupational decision-related processes of adolescents, in terms of the extent to which they may be amotivated about choosing a future occupation. A theoretical framework guided the study. A questionnaire that had previously been administered to an Australian adolescent sample…

Infection with Pathogens Transmitted Commonly Through Food and the Effect of Increasing Use of Culture-Independent Diagnostic Tests on Surveillance--Foodborne Diseases Active Surveillance Network, 10 U.S. Sites, 2012-2015.

PubMed

Huang, Jennifer Y; Henao, Olga L; Griffin, Patricia M; Vugia, Duc J; Cronquist, Alicia B; Hurd, Sharon; Tobin-D'Angelo, Melissa; Ryan, Patricia; Smith, Kirk; Lathrop, Sarah; Zansky, Shelley; Cieslak, Paul R; Dunn, John; Holt, Kristin G; Wolpert, Beverly J; Patrick, Mary E

2016-04-15

To evaluate progress toward prevention of enteric and foodborne illnesses in the United States, the Foodborne Diseases Active Surveillance Network (FoodNet) monitors the incidence of laboratory-confirmed infections caused by nine pathogens transmitted commonly through food in 10 U.S. sites. This report summarizes preliminary 2015 data and describes trends since 2012. In 2015, FoodNet reported 20,107 confirmed cases (defined as culture-confirmed bacterial infections and laboratory-confirmed parasitic infections), 4,531 hospitalizations, and 77 deaths. FoodNet also received reports of 3,112 positive culture-independent diagnostic tests (CIDTs) without culture-confirmation, a number that has markedly increased since 2012. Diagnostic testing practices for enteric pathogens are rapidly moving away from culture-based methods. The continued shift from culture-based methods to CIDTs that do not produce the isolates needed to distinguish between strains and subtypes affects the interpretation of public health surveillance data and ability to monitor progress toward prevention efforts. Expanded case definitions and strategies for obtaining bacterial isolates are crucial during this transition period.

A challenge to lepton universality in B-meson decays

DOE PAGES

Ciezarek, Gregory; Franco Sevilla, Manuel; Hamilton, Brian; ...

2017-06-07

One of the key assumptions of the standard model of particle physics is that the interactions of the charged leptons, namely electrons, muons and taus, differ only because of their different masses. Whereas precision tests comparing processes involving electrons and muons have not revealed any definite violation of this assumption, recent studies of B-meson decays involving the higher-mass tau lepton have resulted in observations that challenge lepton universality at the level of four standard deviations. Here, a confirmation of these results would point to new particles or interactions, and could have profound implications for our understanding of particle physics.

Communication and Technology in Genetic Counseling for Familial Cancer

PubMed Central

Lynch, Henry T.; Snyder, Carrie; Stacey, Mark; Olson, Brooke; Peterson, Susan; Buxbaum, Sarah; Shaw, Trudy; Lynch, Patrick

2015-01-01

When a cancer predisposing germline mutation is detected in an index case, the presence of the underlying syndrome is confirmed and the potential for predictive testing of at-risk relatives is established. However, the reporting of a positive family history does not routinely lead to communication of information about risk to close, much less distant relatives. This review summarizes information technology utilized to address penetration or “reach” of knowledge of risk within extended families, including the use of telephone and video counseling to reach distant patients, and anticipate novel internet-based processes for communication between investigators and relatives. PMID:24355094

Salvaging and Conserving Water Damaged Photographic Materials

NASA Astrophysics Data System (ADS)

Suzuki, Ryuji

Degradation of water damaged photographic materials is discussed; the most vulnerable elements are gelatin layers and silver image. A simple and inexpensive chemical treatment is proposed, consisting of a bath containing a gelatin-protecting biocide and a silver image protecting agent. These ingredients were selected among those used in manufacturing of silver halide photographic emulsions or processing chemicals. Experiments confirmed that this treatment significantly reduced oxidative attacks to silver image and bacterial degradation of gelatin layers. The treated material was also stable under intense light fading test. Method of hardening gelatin to suppress swelling is also discussed.

Soil simulant sourcing for the ExoMars rover testbed

NASA Astrophysics Data System (ADS)

Gouache, Thibault P.; Patel, Nildeep; Brunskill, Christopher; Scott, Gregory P.; Saaj, Chakravarthini M.; Matthews, Marcus; Cui, Liang

2011-06-01

ExoMars is the European Space Agency (ESA) mission to Mars planned for launch in 2018, focusing on exobiology with the primary objective of searching for any traces of extant or extinct carbon-based micro-organisms. The on-surface mission is performed by a near-autonomous mobile robotic vehicle (also referred to as the rover) with a mission design life of 180 sols (Patel et al., 2010). In order to obtain useful data on the tractive performance of the ExoMars rover before flight, it is necessary to perform mobility tests on representative soil simulant materials producing a Martian terrain analogue under terrestrial laboratory conditions. Three individual types of regolith shown to be found extensively on the Martian surface were identified for replication using commercially available terrestrial materials, sourced from UK sites in order to ensure easy supply and reduce lead times for delivery. These materials (also referred to as the Engineering Soil (ES-x) simulants) are: a fine dust analogue (ES-1); a fine aeolian sand analogue (ES-2); and a coarse sand analogue (ES-3). Following a detailed analysis, three fine sand regolith types were identified from commercially available products. Each material was used in its off-the-shelf state, except for ES-2, where further processing methods were used to reduce the particle size range. These materials were tested to determine their physical characteristics, including the particle size distribution, particle density, particle shape (including angularity/sphericity) and moisture content. The results are analysed to allow comparative analysis with existing soil simulants and the published results regarding in situ analysis of Martian soil on previous NASA (National Aeronautics and Space Administration) missions. The findings have shown that in some cases material properties vary significantly from the specifications provided by material suppliers. This has confirmed the need for laboratory testing to determine the actual parameters to prove that standard geotechnical processes are indeed suitable. The outcomes have allowed the confirmation of each simulant material as suitable for replicating their respective regolith types.

Tension fracture of laminates for transport fuselage. Part 2: Large notches

NASA Technical Reports Server (NTRS)

Walker, Tom H.; Ilcewicz, Larry B.; Polland, D. R.; Poe, C. C., Jr.

1993-01-01

Tests were conducted on over 200 center-crack specimens to evaluate: (a) the tension-fracture performance of candidate materials and laminates for commercial fuselage applications; and (b) the accuracy of several failure criteria in predicting response. Crack lengths of up to 12 inches were considered. Other variables included fiber/matrix combination, layup, lamination manufacturing process, and intraply hybridization. Laminates fabricated using the automated tow-placement process provided significantly higher tension-fracture strengths than nominally identical tape laminates. This confirmed earlier findings for other layups, and possibly relates to a reduced stress concentration resulting from a larger scale of repeatable material inhomogeneity in the tow-placed laminates. Changes in material and layup result in a trade-off between small-notch and large-notch strengths. Toughened resins and 0 deg-dominate layups result in higher small-notch strengths but lower large-notch strengths than brittle resins, 90 deg and 45 deg dominated layups, and intraply S2-glass hybrid material forms. Test results indicate that strength-prediction methods that allow for a reduced order singularity of the crack-tip stress field are more successful at predicting failure over a range of notch sizes than those relying on the classical square-root singularity. The order of singularity required to accurately predict large-notch strength from small-notch data was affected by both material and layup. Measured crack-tip strain distributions were generally higher than those predicted using classical methods. Traditional methods of correcting for finite specimen width were found to be lacking, confirming earlier findings with other specimen geometries. Fracture tests of two stiffened panels, identical except for differing materials, with severed central stiffeners resulted in nearly identical damage progression and failure sequences. Strain-softening laws implemented within finite element models appear attractive to account for load redistribution in configured structure due to damage-induced crack tip softening

The prevalence of medial coronoid process disease is high in lame large breed dogs and quantitative radiographic assessments contribute to the diagnosis.

PubMed

Mostafa, Ayman; Nolte, Ingo; Wefstaedt, Patrick

2018-06-05

Medial coronoid process disease is a common leading cause of thoracic limb lameness in dogs. Computed tomography and arthroscopy are superior to radiography to diagnose medial coronoid process disease, however, radiography remains the most available diagnostic imaging modality in veterinary practice. Objectives of this retrospective observational study were to describe the prevalence of medial coronoid process disease in lame large breed dogs and apply a novel method for quantifying the radiographic changes associated with medial coronoid process and subtrochlear-ulnar region in Labrador and Golden Retrievers with confirmed medial coronoid process disease. Purebred Labrador and Golden Retrievers (n = 143, 206 elbows) without and with confirmed medial coronoid process disease were included. The prevalence of medial coronoid process disease in lame large breed dogs was calculated. Mediolateral and craniocaudal radiographs of elbows were analyzed to assess the medial coronoid process length and morphology, and subtrochlear-ulnar width. Mean grayscale value was calculated for radial and subtrochlear-ulnar zones. The prevalence of medial coronoid process disease was 20.8%. Labrador and Golden Retrievers were the most affected purebred dogs (29.6%). Elbows with confirmed medial coronoid process disease had short (P < 0.0001) and deformed (∼95%) medial coronoid process, with associated medial coronoid process osteophytosis (7.5%). Subtrochlear-ulnar sclerosis was evidenced in ∼96% of diseased elbows, with a significant increase (P < 0.0001) in subtrochlear-ulnar width and standardized grayscale value. Radial grayscale value did not differ between groups. Periarticular osteophytosis was identified in 51.4% of elbows with medial coronoid process disease. Medial coronoid process length and morphology, and subtrochlear-ulnar width and standardized grayscale value varied significantly in dogs with confirmed medial coronoid process disease compared to controls. Findings indicated that medial coronoid process disease has a high prevalence in lame large breed dogs and that quantitative radiographic assessments can contribute to the diagnosis. © 2018 American College of Veterinary Radiology.

Completion of evaluation of manufacturing processes for B/Al composites containing 0.2mm diameter boron fibers

NASA Technical Reports Server (NTRS)

Moore, T. J.; Moorhead, P. E.

1980-01-01

Four fabricators produced a total of 54 B/1100 Al, B/6061 Al, and B/2024 Al panels for evaluation. The 8 ply unidirectional, 45 to 50 volume percent, panels were made using 0.20 mm diameter boron fibers which were obtained from a single supplier. Hot press consolidation was carried out in vacuum except for one set of dry woven tape panels which were hot pressed in air. A single testing contractor conducted nondestructive inspection, metallography, fractography and mechanical property tests. The mechanical property tests included 21 and 260 C tensile tests and 21 C shear tests. Panel quality, as measured by nondestructive evaluation, was generally good as were the 21 C tensile properties. The panels hot pressed in air delaminated in the shear tests. Shear strength values were lower in these panels. But tensile strengths were not affected by the delaminations because of the relation between the tensile loading direction and the delaminations. Composite tensile strength was found to be proportional to the volume percent boron and the aluminum matrix rather than to the tape used or fabrication technique. Suitability of these composites for 260 C service was confirmed by tensile tests.

Mechanical Properties of Friction Stir Welds in A12195-T8

NASA Technical Reports Server (NTRS)

Kinchen, David G.; Li, Zhixian; Adams, Glynn P.

1999-01-01

An extensive study of the mechanical properties of friction stir welded Al-Li 2195 has been conducted by Lockheed Martin Michoud Space Systems under contract to NASA. The study was part of a development program in which weld parameters were defined for using FSW to assemble large-scale aluminum cryogenic tanks. In excess of 300 feet of 0.320 in. gage plate material was welded and tested. The tests include room temperature and cryogenic temperature tensile tests and surface crack tension (SCT) tests, nondestructive evaluation, metallurgical studies, and photostress analysis. The results of the testing demonstrated improved mechanical properties with FSW as compared to typical fusion welding processes. Increases in ultimate tensile strength, cryogenic enhancement and elongation were observed with the tensile test results. Increased fracture toughness was observed with the SCT results. Nondestructive evaluations were conducted on all welded Joints. No volumetric defects were indicated. Surface indications on the root side of the welds did not significantly affect weld strength. The results of the nondestructive evaluations were confirmed via metallurgical studies. Photostress analysis revealed strain concentrations in multi-pass and heat-repaired FSW's. Details of the tests and results are presented.

Retrieving self-vocalized information: An event-related potential (ERP) study on the effect of retrieval orientation.

PubMed

Rosburg, Timm; Johansson, Mikael; Sprondel, Volker; Mecklinger, Axel

2014-11-18

Retrieval orientation refers to a pre-retrieval process and conceptualizes the specific form of processing that is applied to a retrieval cue. In the current event-related potential (ERP) study, we sought to find evidence for an involvement of the auditory cortex when subjects attempt to retrieve vocalized information, and hypothesized that adopting retrieval orientation would be beneficial for retrieval accuracy. During study, participants saw object words that they subsequently vocalized or visually imagined. At test, participants had to identify object names of one study condition as targets and to reject object names of the second condition together with new items. Target category switched after half of the test trials. Behaviorally, participants responded less accurately and more slowly to targets of the vocalize condition than to targets of the imagine condition. ERPs to new items varied at a single left electrode (T7) between 500 and 800ms, indicating a moderate retrieval orientation effect in the subject group as a whole. However, whereas the effect was strongly pronounced in participants with high retrieval accuracy, it was absent in participants with low retrieval accuracy. A current source density (CSD) mapping of the retrieval orientation effect indicated a source over left temporal regions. Independently from retrieval accuracy, the ERP retrieval orientation effect was surprisingly also modulated by test order. Findings are suggestive for an involvement of the auditory cortex in retrieval attempts of vocalized information and confirm that adopting retrieval orientation is potentially beneficial for retrieval accuracy. The effects of test order on retrieval-related processes might reflect a stronger focus on the newness of items in the more difficult test condition when participants started with this condition. Copyright © 2014 Elsevier Inc. All rights reserved.

Performance of a Novel Algorithm Using Automated Digital Microscopy for Diagnosing Tuberculosis.

PubMed

Ismail, Nazir A; Omar, Shaheed V; Lewis, James J; Dowdy, David W; Dreyer, Andries W; van der Meulen, Hermina; Nconjana, George; Clark, David A; Churchyard, Gavin J

2015-06-15

TBDx automated microscopy is a novel technology that processes digital microscopic images to identify acid-fast bacilli (AFB). Use of TBDx as part of a diagnostic algorithm could improve the diagnosis of tuberculosis (TB), but its performance characteristics have not yet been formally tested. To evaluate the performance of the TBDx automated microscopy system in algorithms for diagnosis of TB. Prospective samples from patients with presumed TB were processed in parallel with conventional smear microscopy, TBDx microscopy, and liquid culture. All TBDx-positive specimens were also tested with the Xpert MTB/RIF (GXP) assay. We evaluated the sensitivity and specificity of two algorithms-(1) TBDx-GXP (TBDx with positive specimens tested by Xpert MTB/RIF) and (2) TBDx alone-against the gold standard liquid media culture. Of 1,210 samples, 1,009 were eligible for evaluation, of which 109 were culture positive for Mycobacterium tuberculosis. The TBDx system identified 70 specimens (68 culture positive) as having 10 or more putative AFB (high positive) and 207 (19 culture positive) as having 1-9 putative AFB (low positive). An algorithm in which "low-positive" results on TBDx were confirmed by GXP had 78% sensitivity (85 of 109) and 99.8% specificity (889 of 900), requiring 21% (207 of 1,009) specimens to be processed by GXP. As a stand-alone test, a "high-positive" result on TBDx had 62% sensitivity and 99.7% specificity. TBDx used in diagnostic algorithms with GXP provided reasonable sensitivity and high specificity for active TB while dramatically reducing the number GXP tests performed. As a stand-alone microscopy system, its performance was equivalent to that of a highly experienced TB microscopist.

Current status of syphilis in pregnant women in Japan.

PubMed

Suzuki, Shunji; Sekizawa, Akihiko; Tanaka, Masanobu; Okai, Takashi; Kinoshita, Katsuyuki; Kitamura, Tadaichi

2017-12-01

We examined the current status of syphilis-infected pregnant Japanese women, according to the results of syphilis screening and confirmation tests of women who gave birth in Japan between October, 2015 and March, 2016. We requested 2458 obstetrical facilities to provide information of syphilis screening tests and 78.1% of them responded. Considering the response rate and the rate of implementation of confirmation tests, the number of syphilis-infected pregnant Japanese women was estimated to be 250 (1/4022) per year.

Exploring the initial steps of the testing process: frequency and nature of pre-preanalytic errors.

PubMed

Carraro, Paolo; Zago, Tatiana; Plebani, Mario

2012-03-01

Few data are available on the nature of errors in the so-called pre-preanalytic phase, the initial steps of the testing process. We therefore sought to evaluate pre-preanalytic errors using a study design that enabled us to observe the initial procedures performed in the ward, from the physician's test request to the delivery of specimens in the clinical laboratory. After a 1-week direct observational phase designed to identify the operating procedures followed in 3 clinical wards, we recorded all nonconformities and errors occurring over a 6-month period. Overall, the study considered 8547 test requests, for which 15 917 blood sample tubes were collected and 52 982 tests undertaken. No significant differences in error rates were found between the observational phase and the overall study period, but underfilling of coagulation tubes was found to occur more frequently in the direct observational phase (P = 0.043). In the overall study period, the frequency of errors was found to be particularly high regarding order transmission [29 916 parts per million (ppm)] and hemolysed samples (2537 ppm). The frequency of patient misidentification was 352 ppm, and the most frequent nonconformities were test requests recorded in the diary without the patient's name and failure to check the patient's identity at the time of blood draw. The data collected in our study confirm the relative frequency of pre-preanalytic errors and underline the need to consensually prepare and adopt effective standard operating procedures in the initial steps of laboratory testing and to monitor compliance with these procedures over time.

Treatment of model solutions and wastewater containing selected hazardous metal ions using a chitin/lignin hybrid material as an effective sorbent.

PubMed

Bartczak, Przemysław; Klapiszewski, Łukasz; Wysokowski, Marcin; Majchrzak, Izabela; Czernicka, Weronika; Piasecki, Adam; Ehrlich, Hermann; Jesionowski, Teofil

2017-12-15

A chitin/lignin material with defined physicochemical and morphological properties was used as an effective adsorbent of environmentally toxic metals from model systems. Particularly significant is its use in the neutralization of real industrial wastes. The ions Ni 2+ , Cu 2+ , Zn 2+ and Pb 2+ were adsorbed on the functional sorbent, confirming the high sorption capacity of the newly obtained product, primarily due to the presence on its surface of numerous active functional groups from the component biopolymers. The kinetics of the process of ion adsorption from model solution were investigated, and the experimental data were found to fit significantly better to a type 1 pseudo-second-order kinetic model, as confirmed by the high correlation coefficient of 0.999 for adsorption of both nickel(II) copper(II) zinc(II) and lead(II) ions. The experimental data obtained on the basis of adsorption isotherms corresponded to the Langmuir model. The sorption capacity of the chitin/lignin material was measured at 70.41 mg(Ni 2+ )/g, 75.70 mg(Cu 2+ )/g, 82.41 mg(Zn 2+ )/g and 91.74 mg(Pb 2+ )/g. Analysis of thermodynamic parameters confirmed the endothermic nature of the process. It was also shown that nitric acid is a very effective desorbing (regenerating) agent, enabling the chitin/lignin material to be reused as an effective sorbent of metal ions. The sorption abilities of the chitin/lignin system with respect to particular metal ions can be ordered in the sequence Ni 2+

Next Generation Solvent (NGS): Development for Caustic-Side Solvent Extraction of Cesium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, Bruce A.; Birdwell, Jr, Joseph F.; Bonnesen, Peter V.

This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Interlaboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

Next Generation Solvent Development for Caustic-Side Solvent Extraction of Cesium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, Bruce A.; Birdwell, Joseph F.; Bonnesen, Peter V.

This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Inter laboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

Use of Fisheye Parrot Bebop 2 Images for 3d Modelling Using Commercial Photogrammetric Software

NASA Astrophysics Data System (ADS)

Pagliari, D.; Pinto, L.

2018-05-01

Fisheye camera installed on-board mass market UAS are becoming very popular and it is more and more frequent the use of such platforms for photogrammetric purposes. The interest of wide-angles images for 3D modelling is confirmed by the introduction of fisheye models in several commercial software packages. The paper exploits the different mathematical models implemented in the most famous commercial photogrammetric software packages, highlighting the different processing pipelines and analysing the achievable results in terms of checkpoint residuals, as well as the quality of the delivered 3D point clouds. A two-step approach based on the creation of undistorted images has been tested too. An experimental test has been carried out using a Parrot Bebop 2 UAS by performing a flight over an historical complex located near Piacenza (Northern Italy), which is characterized by the simultaneous presence of horizontal, vertical and oblique surfaces. Different flight configurations have been tested to evaluate the potentiality and possible drawbacks of the previously mentioned UAS platform. Results confirmed that the fisheye images acquired with the Parrot Bebop 2 are suitable for 3D modelling, ensuring accuracies of the photogrammetric blocks of the order of the GSD (about 0.05 m normal to the optic axis in case of a flight height equal to 35 m). The generated point clouds have been compared to a reference scan, acquired by means of a MS60 MultiStation, resulting in differences below 0.05 in all directions.

DNA damage in spermatozoa from infertile men with varicocele evaluated by sperm chromatin dispersion and DBD-FISH.

PubMed

Cortés-Gutiérrez, Elva I; Dávila-Rodríguez, Martha I; Fernández, José Luis; López-Fernández, Carmen; Aragón-Tovar, Anel R; Urbina-Bernal, Luis C; Gosálvez, Jaime

2016-01-01

Evaluation of DNA integrity is an important test, possessing greater diagnostic and prognostic significance for couples requiring assisted reproduction. In this study, we evaluate the levels of DNA damage in infertile patients with varicocele with respect to fertile males by the sperm chromatin dispersion (SCD) test. The presence of DNA breaks in spermatozoa was confirmed by DNA breakage detection-fluorescence in situ hybridization (DBD-FISH). In this study, the frequency of sperm cells with fragmented DNA was studied in a group of 20 infertile patients with varicocele and compared with 20 fertile males. The spermatozoa were processed to classify different levels of DNA fragmentation using the Halosperm(®) kit, an improved SCD test, and DBD-FISH. Patients with varicocele showed 25.54 ± 28.17 % of spermatozoa with fragmented DNA, significantly higher than those of the group of fertile subjects (11.54 ± 3.88 %). The proportion of degraded cells in total sperm cells with fragmented DNA was sixfold higher in the case of patients with varicocele. The presence of DNA breaks in spermatozoa was confirmed by DBD-FISH. 5-bp Classical satellite-2 regions showed greater sensitivity to damage or "breakage" than alphoid satellite regions. Our finding preliminary demonstrated an increase of DNA fragmentation associated to severe sperm damage, in infertile patients with varicocele with respect to fertile males. 5-bp Classical satellite-2 regions showed greater sensitivity to damage or "breakage" than alphoid satellite regions.

Analysis of anabolic steroids in human hair using LC-MS/MS.

PubMed

Deshmukh, Nawed; Hussain, Iltaf; Barker, James; Petroczi, Andrea; Naughton, Declan P

2010-10-01

New highly sensitive, specific, reliable, reproducible and robust LC-MS/MS methods were developed to detect the anabolic steroids, nandrolone and stanozolol, in human hair for the first time. Hair samples from 180 participants (108 males, 72 females, 62% athletes) were screened using ELISA which revealed 16 athletes as positive for stanozolol and 3 for nandrolone. Positive samples were confirmed on LC-MS/MS in selective reaction monitoring (SRM) mode. The assays for stanozolol and nandrolone showed good linearity in the range 1-400pg/mg and 5-400pg/mg, respectively. The methods were validated for LLOD, interday precision, intraday precision, specificity, extraction recovery and accuracy. The assays were capable of detecting 0.5pg stanozolol and 3.0pg nandrolone per mg of hair, when approximately 20mg of hair were processed. Analysis using LC-MS/MS confirmed 11 athletes' positive for stanozolol (5.0pg/mg to 86.3pg/mg) and 1 for nandrolone (14.0pg/mg) thus avoiding false results from ELISA screening. The results obtained demonstrate the application of these hair analysis methods to detect both steroids at low concentrations, hence reducing the amount of hair required significantly. The new methods complement urinalysis or blood testing and facilitate improved doping testing regimes. Hair analysis benefits from non-invasiveness, negligible risk of infection and facile sample storage and collection, whilst reducing risks of tampering and cross-contamination. Owing to the wide detection window, this approach may also offer an alternative approach for out-of-competition testing.

Development of a survey instrument to measure patient experience of integrated care.

PubMed

Walker, Kara Odom; Stewart, Anita L; Grumbach, Kevin

2016-06-01

Healthcare systems are working to move towards more integrated, patient-centered care. This study describes the development and testing of a multidimensional self-report measure of patients' experiences of integrated care. Random-digit-dial telephone survey in 2012 of 317 adults aged 40 years or older in the San Francisco region who had used healthcare at least twice in the past 12 months. One-time cross-sectional survey; psychometric evaluation to confirm dimensions and create multi-item scales. Survey data were analyzed using VARCLUS and confirmatory factor analysis and internal consistency reliability testing. Scales measuring five domains were confirmed: coordination within and between care teams, navigation (arranging appointments and visits), communication between specialist and primary care doctor, and communication between primary care doctor and specialist. Four of these demonstrated excellent internal consistency reliability. Mean scale scores indicated low levels of integration. These scales measuring integrated care capture meaningful domains of patients' experiences of health care. The low levels of care integration reported by patients in the study sample suggest that these types of measures should be considered in ongoing evaluations of health system performance and improvement. Further research should examine whether differences in patient experience of integrated care are associated with differences in the processes and outcomes of care received.

The contribution of p53 and Y chromosome long arm genes to regulation of apoptosis in mouse testis.

PubMed

Lech, Tomasz; Styrna, Józefa; Kotarska, Katarzyna

2018-03-01

Apoptosis of excessive or defective germ cells is a natural process occurring in mammalian testes. Tumour suppressor protein p53 is involved in this process both in developing and adult male gonads. Its contribution to testicular physiology is known to be modified by genetic background. The aim of this study was to evaluate the combined influence of the p53 and Y chromosome long arm genes on male germ cell apoptosis. Knockout of the transformation related protein 53 (Trp53) gene was introduced into congenic strains: B10.BR (intact Y chromosome) and B10.BR-Ydel (Y chromosome with a deletion in the long arm). The level of apoptosis in the testes of 19-day-old and 3-month-old male mice was determined using the terminal deoxynucleotidyl transferase-mediated deoxyuridine triphosphate in situ nick-end labelling (TUNEL) method. The study revealed that although p53 is involved in germ cell apoptosis in peripubertal testes, this process can also be mediated by p53-independent mechanisms. However, activation of p53-independent apoptotic pathways in the absence of the p53 protein requires engagement of the multicopy Yq genes and was not observed in gonads of B10.BR-Ydel-p53-/- males. The role of Yq genes in the regulation of testicular apoptosis seems to be restricted to the initial wave of spermatogenesis and is not evident in adult gonads. The study confirmed, instead, that p53 does participate in spontaneous apoptosis in mature testes.

Basal ganglia, thalamus and neocortical atrophy predicting slowed cognitive processing in multiple sclerosis.

PubMed

Batista, Sonia; Zivadinov, Robert; Hoogs, Marietta; Bergsland, Niels; Heininen-Brown, Mari; Dwyer, Michael G; Weinstock-Guttman, Bianca; Benedict, Ralph H B

2012-01-01

Information-processing speed (IPS) slowing is a primary cognitive deficit in multiple sclerosis (MS). Basal ganglia, thalamus and neocortex are thought to have a key role for efficient information-processing, yet the specific relative contribution of these structures for MS-related IPS impairment is poorly understood. To determine if basal ganglia and thalamus atrophy independently contribute to visual and auditory IPS impairment in MS, after controlling for the influence of neocortical volume, we enrolled 86 consecutive MS patients and 25 normal controls undergoing 3T brain MRI and neuropsychological testing. Using Sienax and FIRST software, neocortical and deep gray matter (DGM) volumes were calculated. Neuropsychological testing contributed measures of auditory and visual IPS using the Paced Auditory Serial Addition Test (PASAT) and the Symbol Digit Modalities Test (SDMT), respectively. MS patients exhibited significantly slower IPS relative to controls and showed reduction in neocortex, caudate, putamen, globus pallidus, thalamus and nucleus accumbens volume. SDMT and PASAT were significantly correlated with all DGM regions. These effects were mitigated by controlling for the effects of neocortical volume, but all DGM volumes remained significantly correlated with SDMT, putamen (r = 0.409, p < 0.001) and thalamus (r = 0.362, p < 0.001) having the strongest effects, whereas for PASAT, the correlation was significant for putamen (r = 0.313, p < 0.01) but not for thalamus. We confirm the significant role of thalamus atrophy in MS-related IPS slowing and find that putamen atrophy is also a significant contributor to this disorder. These DGM structures have independent, significant roles, after controlling for the influence of neocortex atrophy.

Orion flight test previewed on This Week @NASA - November 7, 2014

NASA Image and Video Library

2014-11-07

A NASA media briefing on Nov. 6 at Kennedy Space Center highlighted the fully assembled Orion spacecraft and details of its first test flight, scheduled for Dec. 4. The 4 and-a-half hour flight, called Exploration Flight Test-1, will send Orion 3,600 miles from Earth on a two-orbit flight to confirm its critical systems are ready for the challenges of eventually sending astronauts on deep space missions to an asteroid and Mars. Also, Delta IV Heavy wet dress test, Next ISS crew trains, Space agency leaders support ISS, Curiosity confirms orbital data and more!

Reliability of the cloned-enzyme donor immunoassay (CEDIA) for cocaine in human serum in the range between the detection limit and the cut-off.

PubMed

Schütz, Harald; Auch, Jürgen; Erdmann, Freidoon; Weiler, Günter; Verhoff, Marcel A

2006-01-01

Immunoassays are used worldwide for the rapid screening of drugs. Despite the fact that they are highly valuable tools for the testing of legal and illicit drugs, there is a non-negligable risk of false-positive and false-negative findings and many pitfalls must be taken into account when using these tests in an uncritical manner and without valid confirmation procedures. In order to check the correlation between cloned-enzyme donor immunoassay (CEDIA) readings and exact determined gas chromatography/mass spectrometry (GC/MS) values for benzoylecgonine, a total of 472 serum samples was measured with an immunoassay (CEDIA) as well as GC/MS. As a result, it was shown that in the lower area of concentration, up to approx. 300 ng equ. benzoylecgonine/ml, there is a semiquantitative useful correlation. With higher concentrations, the values shift more and more apart and many runaways are visible. Generally the use of tests for materials other than those declared is excluded from the manufacturer's warranty and is at the user's own risk, but the authors found that many immunochemical tests with a certification only for the use in urine are well suited to the screening of serum samples, and even low readings could be confirmed by GC/MS. With blood or serum as sample, it could be regularly observed that generally very small readings could not only be confirmed with mass spectrometry but could in most cases also be quantified. This was the key factor in determining the rate of confirmation in 495 cases. In total, an incredibly high reliability for the CEDIA cocaine test (via benzoylecgonine) was shown up to the area of detection (detection limit), far below the cut-off. These results confirm the extraordinary sensitivity and specificity of this test also for blood or serum as sample material to be tested.

Emotional Intelligence and Mismatching Expressive and Verbal Messages: A Contribution to Detection of Deception

PubMed Central

Wojciechowski, Jerzy; Stolarski, Maciej; Matthews, Gerald

2014-01-01

Processing facial emotion, especially mismatches between facial and verbal messages, is believed to be important in the detection of deception. For example, emotional leakage may accompany lying. Individuals with superior emotion perception abilities may then be more adept in detecting deception by identifying mismatch between facial and verbal messages. Two personal factors that may predict such abilities are female gender and high emotional intelligence (EI). However, evidence on the role of gender and EI in detection of deception is mixed. A key issue is that the facial processing skills required to detect deception may not be the same as those required to identify facial emotion. To test this possibility, we developed a novel facial processing task, the FDT (Face Decoding Test) that requires detection of inconsistencies between facial and verbal cues to emotion. We hypothesized that gender and ability EI would be related to performance when cues were inconsistent. We also hypothesized that gender effects would be mediated by EI, because women tend to score as more emotionally intelligent on ability tests. Data were collected from 210 participants. Analyses of the FDT suggested that EI was correlated with superior face decoding in all conditions. We also confirmed the expected gender difference, the superiority of high EI individuals, and the mediation hypothesis. Also, EI was more strongly associated with facial decoding performance in women than in men, implying there may be gender differences in strategies for processing affective cues. It is concluded that integration of emotional and cognitive cues may be a core attribute of EI that contributes to the detection of deception. PMID:24658500

Anaphylaxis to Gelofusine confirmed by in vitro basophil activation test: a case series.

PubMed

Apostolou, E; Deckert, K; Puy, R; Sandrini, A; de Leon, M P; Douglass, J A; Rolland, J M; O'hehir, R E

2006-03-01

The plasma expander Gelofusine (succinylated gelatin) is a recognised cause of peri-operative anaphylaxis. Current diagnosis of Gelofusine sensitivity is by skin testing, a procedure that itself carries a risk of allergic reaction. We evaluated the reliability of the in vitro basophil activation test as a diagnostic assay for Gelofusine sensitivity in subjects with a clinical history highly suggestive of Gelofusine allergy. Six patients with peri-operative anaphylaxis clinically attributed to Gelofusine were skin tested to confirm sensitivity. Control subjects included three healthy subjects and five subjects allergic to a neuromuscular blocking drug, all negative on Gelofusine skin testing. Whole blood basophil activation to Gelofusine was analysed by flow cytometry for CD63 surface expression. All of the Gelofusine sensitive patients and one of the control allergic subjects showed positive basophil activation to Gelofusine. In this series of subjects, the basophil activation test for Gelofusine allergy had a sensitivity of 100% and a specificity of 87.5%. Our findings suggest that basophil activation testing is a safe and reliable in vitro assay for prediction or confirmation of Gelofusine sensitivity in patients with high clinical suspicion of Gelofusine-induced anaphylaxis.

Corrugator activity confirms immediate negative affect in surprise

PubMed Central

Topolinski, Sascha; Strack, Fritz

2015-01-01

The emotion of surprise entails a complex of immediate responses, such as cognitive interruption, attention allocation to, and more systematic processing of the surprising stimulus. All these processes serve the ultimate function to increase processing depth and thus cognitively master the surprising stimulus. The present account introduces phasic negative affect as the underlying mechanism responsible for this switch in operating mode. Surprising stimuli are schema-discrepant and thus entail cognitive disfluency, which elicits immediate negative affect. This affect in turn works like a phasic cognitive tuning switching the current processing mode from more automatic and heuristic to more systematic and reflective processing. Directly testing the initial elicitation of negative affect by surprising events, the present experiment presented high and low surprising neutral trivia statements to N = 28 participants while assessing their spontaneous facial expressions via facial electromyography. High compared to low surprising trivia elicited higher corrugator activity, indicative of negative affect and mental effort, while leaving zygomaticus (positive affect) and frontalis (cultural surprise expression) activity unaffected. Future research shall investigate the mediating role of negative affect in eliciting surprise-related outcomes. PMID:25762956

Corrugator activity confirms immediate negative affect in surprise.

PubMed

Topolinski, Sascha; Strack, Fritz

2015-01-01

The emotion of surprise entails a complex of immediate responses, such as cognitive interruption, attention allocation to, and more systematic processing of the surprising stimulus. All these processes serve the ultimate function to increase processing depth and thus cognitively master the surprising stimulus. The present account introduces phasic negative affect as the underlying mechanism responsible for this switch in operating mode. Surprising stimuli are schema-discrepant and thus entail cognitive disfluency, which elicits immediate negative affect. This affect in turn works like a phasic cognitive tuning switching the current processing mode from more automatic and heuristic to more systematic and reflective processing. Directly testing the initial elicitation of negative affect by surprising events, the present experiment presented high and low surprising neutral trivia statements to N = 28 participants while assessing their spontaneous facial expressions via facial electromyography. High compared to low surprising trivia elicited higher corrugator activity, indicative of negative affect and mental effort, while leaving zygomaticus (positive affect) and frontalis (cultural surprise expression) activity unaffected. Future research shall investigate the mediating role of negative affect in eliciting surprise-related outcomes.

Associations of dietary patterns with bone mass, muscle strength and balance in a cohort of Australian middle-aged women.

PubMed

Wu, Feitong; Wills, Karen; Laslett, Laura L; Oldenburg, Brian; Jones, Graeme; Winzenberg, Tania

2017-10-01

Influences of dietary patterns on musculoskeletal health are poorly understood in middle-aged women. This cross-sectional analysis from a cohort of 347 women (aged 36-57 years) aimed to examine associations between dietary patterns and musculoskeletal health outcomes in middle-aged women. Diet was measured by the Cancer Council of Victoria FFQ. Total body bone mineral content (TB BMC), femoral neck and lumbar spine bone density (dual-energy X-ray absorptiometry), lower limbs muscle strength (LMS) and balance tests (timed up and go test, step test, functional reach test (FRT) and lateral reach test) were also measured. Exploratory factor analysis was used to identify dietary patterns and scores for each pattern generated using factor loadings with absolute values ≥0·20. Associations between food pattern scores and musculoskeletal outcomes were assessed using multivariable linear regression. Three dietary patterns were identified: 'Healthy' (high consumption of a plant-based diet - vegetables, legumes, fruit, tomatoes, nuts, snacks, garlic, whole grains and low intake of high-fat dairy products), 'high protein, high fat' (red meats, poultry, processed meats, potatoes, cruciferous and dark-yellow vegetables, fish, chips, spirits and high-fat dairy products) and 'Processed foods' (high intakes of meat pies, hamburgers, beer, sweets, fruit juice, processed meats, snacks, spirits, pizza and low intake of cruciferous vegetables). After adjustment for confounders, Healthy pattern was positively associated with LMS, whereas Processed foods pattern was inversely associated with TB BMC and FRT. The associations were not significant after accounting for multiple comparisons. There were no associations with any other outcomes. These results suggest that maintaining a healthy diet could contribute to bone acquisition, muscle strength and balance in adult life. However, while they provide some support for further investigating dietary strategies for prevention of age-related loss of muscle and deterioration in balance, the exploratory nature of the analyses means that confirmation in longitudinal studies and/or trials with pre-specified hypotheses is needed.

[Peracetic acid: alternative to the sterilization of bronchofibroscopes].

PubMed

Villate, J I; Barrón, J; Zalacaín, R; Urcelay, M I; Hernández, J M; Argumedo, M

1997-03-01

The Steris system for cold sterilization with peracetic acid was evaluated by effecting a series of contaminations of a fiberoptic bronchoscope (FB) with specimens of Pseudomonas aeruginosa, Acinetobacter baumanii and Mycobacterium kansasi. The FB was contaminated 24 times, 8 times by each microorganism, using specimens containing more than 10(8) cfu/ml. After fixing the secretions on the FB and washing it with enzyme soap, the BF was sterilized. Specimens were taken for culturing after contamination of the FB, after washing, immediately after sterilization and 1 hour after sterilization. No microorganism growth of any of the samples was detected either immediately after sterilization or one hour later. Microbiological data confirmed contamination of the FB after aspiration and fixation of the inoculate. Chemical and biological tests with B. stearothermophilus spores as specified by the manufacturer were correct in all cases: 24 contaminations and 52 processes of prior training. The efficacy of washing with enzyme soap before sterilization stands out. In 14 of the 24 samples, culture was negative after washing and in 7 the concentration of microorganisms was less than 500 cfu/ml, which confirms the need for appropriate washing before any disinfection or sterilization process is begun. In conclusion, the Steris system based on peracetic acid is an alternative to other systems for cold sterilization or high level disinfection.

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selvakumar, S., E-mail: lathaselvam1963@gmail.com

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization andmore » pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.« less

Insight into multiple-triggering effect in DTSCRs for ESD protection

NASA Astrophysics Data System (ADS)

Zhang, Lizhong; Wang, Yuan; Wang, Yize; He, Yandong

2017-07-01

The diode-triggered silicon-controlled rectifier (DTSCR) is widely used for electrostatic discharge (ESD) protection in advanced CMOS process owing to its advantages, such as design simplification, adjustable trigger/holding voltage, low parasitic capacitance. However, the multiple-triggering effect in the typical DTSCR device may cause undesirable larger overall trigger voltage, which results in a reduced ESD safe margin. In previous research, the major cause is attributed to the higher current level required in the intrinsic SCR. The related discussions indicate that it seems to result from the current division rule between the intrinsic and parasitic SCR formed in the triggering process. In this letter, inserting a large space into the trigger diodes is proposed to get a deeper insight into this issue. The triggering current is observed to be regularly reduced along with the increased space, which confirms that the current division is determined by the parasitic resistance distributed between the intrinsic and parasitic SCR paths. The theoretical analysis is well confirmed by device simulation and transmission line pulse (TLP) test results. The reduced overall trigger voltage is achieved in the modified DTSCR structures due to the comprehensive result of the parasitic resistance vs triggering current, which indicates a minimized multiple-triggering effect. Project supported by the Beijing Natural Science Foundation, China (No. 4162030).

The utilization of waste by-products for removing silicate from mineral processing wastewater via chemical precipitation.

PubMed

Kang, Jianhua; Sun, Wei; Hu, Yuehua; Gao, Zhiyong; Liu, Runqing; Zhang, Qingpeng; Liu, Hang; Meng, Xiangsong

2017-11-15

This study investigates an environmentally friendly technology that utilizes waste by-products (waste acid and waste alkali liquids) to treat mineral processing wastewater. Chemical precipitation is used to remove silicate from scheelite (CaWO 4 ) cleaning flotation wastewater and the waste by-products are used as a substitute for calcium chloride (CaCl 2 ). A series of laboratory experiments is conducted to explain the removal of silicate and the characterization and formation mechanism of calcium silicate. The results show that silicate removal reaches 90% when the Ca:Si molar ratio exceeds 1.0. The X-ray diffraction (XRD) results confirm the characterization and formation of calcium silicate. The pH is the key factor for silicate removal, and the formation of polysilicic acid with a reduction of pH can effectively improve the silicate removal and reduce the usage of calcium. The economic analysis shows that the treatment costs with waste acid (0.63 $/m 3 ) and waste alkali (1.54 $/m 3 ) are lower than that of calcium chloride (2.38 $/m 3 ). The efficient removal of silicate is confirmed by industrial testing at a plant. The results show that silicate removal reaches 85% in the recycled water from tailings dam. Copyright © 2017 Elsevier Ltd. All rights reserved.

Assessment of 48 Stock markets using adaptive multifractal approach

NASA Astrophysics Data System (ADS)

Ferreira, Paulo; Dionísio, Andreia; Movahed, S. M. S.

2017-11-01

In this paper, Stock market comovements are examined using cointegration, Granger causality tests and nonlinear approaches in context of mutual information and correlations. Since underlying data sets are affected by non-stationarities and trends, we also apply Adaptive Multifractal Detrended Fluctuation Analysis (AMF-DFA) and Adaptive Multifractal Detrended Cross-Correlation Analysis (AMF-DXA). We find only 170 pair of Stock markets cointegrated, and according to the Granger causality and mutual information, we realize that the strongest relations lies between emerging markets, and between emerging and frontier markets. According to scaling exponent given by AMF-DFA, h(q = 2) > 1, we find that all underlying data sets belong to non-stationary process. According to Efficient Market Hypothesis (EMH), only 8 markets are classified in uncorrelated processes at 2 σ confidence interval. 6 Stock markets belong to anti-correlated class and dominant part of markets has memory in corresponding daily index prices during January 1995 to February 2014. New-Zealand with H = 0 . 457 ± 0 . 004 and Jordan with H = 0 . 602 ± 0 . 006 are far from EMH. The nature of cross-correlation exponents based on AMF-DXA is almost multifractal for all pair of Stock markets. The empirical relation, Hxy ≤ [Hxx +Hyy ] / 2, is confirmed. Mentioned relation for q > 0 is also satisfied while for q < 0 there is a deviation from this relation confirming behavior of markets for small fluctuations is affected by contribution of major pair. For larger fluctuations, the cross-correlation contains information from both local (internal) and global (external) conditions. Width of singularity spectrum for auto-correlation and cross-correlation are Δαxx ∈ [ 0 . 304 , 0 . 905 ] and Δαxy ∈ [ 0 . 246 , 1 . 178 ] , respectively. The wide range of singularity spectrum for cross-correlation confirms that the bilateral relation between Stock markets is more complex. The value of σDCCA indicates that all pairs of stock market studied in this time interval belong to cross-correlated processes.

Biogenic amine profile in unripe Arabica coffee beans processed according to dry and wet methods.

PubMed

Dias, Eduardo C; Pereira, Rosemary G F A; Borém, Flávio M; Mendes, Eulália; de Lima, Renato R; Fernandes, José O; Casal, Susana

2012-04-25

Immature coffee fruit processing contributes to a high amount of defective beans, which determines a significant amount of low-quality coffee sold in the Brazilian internal market. Unripe bean processing was tested, taking the levels of bioactive amines as criteria for evaluating the extent of fermentation and establishing the differences between processing methods. The beans were processed by the dry method after being mechanically depulped immediately after harvest or after a 12 h resting period in a dry pile or immersed in water. Seven bioactive amines were quantified: putrescine, spermine, spermidine, serotonin, cadaverine, histamine, and tyramine, with global amounts ranging from 71.8 to 80.3 mg/kg. The levels of spermine and spermidine were lower in the unripe depulped coffee than in the natural coffee. The specific conditions of dry and wet processing also influenced cadaverine levels, and histamine was reduced in unripe depulped coffee. A resting period of 12 h does not induce significant alteration on the beans and can be improved if performed in water. These results confirm that peeling immature coffee can decrease fermentation processes while providing more uniform drying, thus reducing the number of defects and potentially increasing beverage quality.

A study of phase defect measurement on EUV mask by multiple detectors CD-SEM

NASA Astrophysics Data System (ADS)

Yonekura, Isao; Hakii, Hidemitsu; Morisaki, Shinya; Murakawa, Tsutomu; Shida, Soichi; Kuribara, Masayuki; Iwai, Toshimichi; Matsumoto, Jun; Nakamura, Takayuki

2013-06-01

We have studied MVM (Multi Vision Metrology) -SEM® E3630 to measure 3D shape of defects. The four detectors (Detector A, B, C and D) are independently set up in symmetry for the primary electron beam axis. Signal processing of four direction images enables not only 2D (width) measurement but also 3D (height) measurement. At last PMJ, we have investigated the relation between the E3630's signal of programmed defect on MoSi-HT and defect height measured by AFM (Atomic Force Microscope). It was confirmed that height of integral profile by this tool is correlated with AFM. It was tested that E3630 has capability of observing multilayer defect on EUV. We have investigated correlation with AFM of width and depth or height of multilayer defect. As the result of observing programmed defects, it was confirmed that measurement result by E3630 is well correlated with AFM. And the function of 3D view image enables to show nm order defect.

Catalytic Graphitization for Preparation of Porous Carbon Material Derived from Bamboo Precursor and Performance as Electrode of Electrical Double-Layer Capacitor

NASA Astrophysics Data System (ADS)

Tsubota, Toshiki; Maguchi, Yuta; Kamimura, Sunao; Ohno, Teruhisa; Yasuoka, Takehiro; Nishida, Haruo

2015-12-01

The combination of addition of Fe (as a catalyst for graphitization) and CO2 activation (a kind of gaseous activation) was applied to prepare a porous carbon material from bamboo powder (a waste product of superheated steam treatment). Regardless of the heat treatment temperature, many macropores were successfully formed after the heating process by removal of Fe compounds. A turbostratic carbon structure was generated in the Fe-added sample heated at 850°C. It was confirmed that the added Fe acted as a template for pore formation. Moreover, it was confirmed that the added Fe acted as a catalyst for graphitization. The resulting electrochemical performance as the electrode of an electrical double-layer capacitor, as demonstrated by cyclic voltammetry, electrochemical impedance spectroscopy, and charge-discharge testing, could be explained based on the graphitization and activation effects. Addition of Fe could affect the electrical properties of carbon material derived from bamboo.

Surface production dominating Cs-free H- ion source for high intensity and high energy proton accelerators

NASA Astrophysics Data System (ADS)

Ueno, Akira; Ikegami, Kiyoshi; Kondo, Yasuhiro

2004-05-01

A Cs-free negative hydrogen (H-) ion source driven by pulsed arc plasma with a LaB6 filament is being operated for the beam tests of the Japan Proton Accelerator Research Complex (J-PARC) linac. A peak H- current of 38 mA, which exceeds the requirement of the J-PARC first stage, is stably extracted from the ion source with a beam duty factor of 0.9% (360 μs×25 Hz) by principally optimizing the surface condition and shape of the plasma electrode. The sufficiently small emittance of the beam was confirmed by high transmission efficiency (around 90%) through the following 324 MHz 3 MeV J-PARC radio frequency quadrupole linac (M. Ikegami et al., Proc. 2003 Part. Accel. Conf. 2003, p. 1509). The process of the optimization, which confirms the validity of hypothesis that H- ions are produced by surface reaction on a Mo plasma electrode dominantly in the ion source, is presented.

Misdescription of packaged foods: a case study from the United Arab Emirates.

PubMed

Premanandh, J; Sabbagh, Aman; Maruthamuthu, M

2013-01-01

Food misdescription has become of paramount importance as consumers come into contact daily with a great variety of foods. The controversies surrounding genetically modified organism (GMO) labelling and malpractices in the food chain have forced regulatory authorities to authenticate food from production to consumption. This paper reports the results of a surveillance programme conducted in the United Arab Emirates (UAE) market to assess the status of food misdescription and authenticity. A DNA test was used to screen random samples of processed meat products bought from supermarkets in the UAE. A total of 246 samples were analysed from different geographical locations. The majority of samples showed a high standard of legal compliance, with over 95% confirmed for authenticity. However, 5% of samples were found to contain undeclared species. In conclusion, this study confirms the presence of undeclared food in the UAE market. Regular surveillance and monitoring programmes along with strict implementation of the Food and Adulteration Act may alleviate misdescription issues to a greater extent.

A sea cucumber-like BiOBr nanosheet/Zn2GeO4 nanorod heterostructure for enhanced visible light driven photocatalytic activity

NASA Astrophysics Data System (ADS)

Zhang, Zhiping; Ge, Xin; Zhang, Xueyu; Duan, Lianfeng; Li, Xuesong; Yang, Yue; Lü, Wei

2018-01-01

In present work, a two-step hydrothermal/solvothermal method was developed to fabricate sea cucumber-like p-n heterojunctions of p-BiOBr/n-Zn2GeO4. The BiOBr nanosheets were grafted onto the surface of Zn2GeO4 nanorods. BiOBr/Zn2GeO4 nanocomposites exhibit remarkable photocatalytic activity under visible-light irradiation, and photocatalytic activity was studied in the catalytic test of rhodamine B decolorization. The mechanism for improved photocatalytic activity is interpreted in terms of the formation of type II band alignment between BiOBr and Zn2GeO4, which is confirmed by UV-vis diffuse absorption and VB-XPS spectra. BiOBr nanosheet as an admirable electron transport medium provide desirable specific surface area for the nanocomposite and a suitable band gap for heterojunction structure. Furthermore, scavenger experiments confirmed that h+ and {{{{O}}}2}\\cdot - were the main oxygen active species in the decolorization process.

Performance of Poly(lactic acid) Surface Modified Films for Food Packaging Application

PubMed Central

Dalla Rosa, Marco; Iordanskii, Alexey L.

2017-01-01

Five Poly(lactic acid) (PLA) film samples were analyzed to study the gas barrier behavior, thermal stability and mechanical performance for food packaging application. O2, CO2, N2, N2O, and C2H4 pure gases; Air; and Modified Atmosphere (MA, 79% N2O/21% O2) were used to analyze the influence of the chemical structure, storage temperature and crystalline phase on the gas barrier behavior. The kinetic of the permeation process was investigated at different temperatures, ranging from 5 °C to 40 °C. Annealing thermal treatment on the samples led to the crystalline percentage, influencing especially the gas solubility process. Thermal properties such as Tg and χc, and mechanical properties such as tensile strength and modulus were remarkably improved with surface PLA modification. A more pronounced reinforcing effect was noted in the case of metallization, as well as improved gas barrier performance. Tensile testing and tensile cycling tests confirmed the rigidity of the films, with about a 20% loss of elasticity after 25 cycles loading. PMID:28773210

Patient satisfaction with a hospital-based neuropsychology service.

PubMed

Foran, Amie; Millar, Elisa; Dorstyn, Diana

2016-09-01

Objective The aim of the present study was to develop and pilot a measure of patient satisfaction that encompasses themes, activities, settings and interactions specific to the neuropsychological assessment process. Methods A focus group of out-patients (n=15) was surveyed to identify the factors commonly associated with a satisfactory neuropsychological experience. Responses informed a purposely designed 14-item patient satisfaction scale (α=0.88) that was completed by 66 hospital out-patients with mild to moderate cognitive impairment. Results Satisfaction with the neuropsychological assessment process was generally reported, with the testing phase (85%) rated significantly more favourably than the pre-assessment (79%) and feedback (70%) phases. Commentaries provided by 32 respondents identified interpersonal facilitators to a satisfactory neuropsychological assessment experience, but also dissatisfaction with physical aspects of the testing environment in addition to service availability. Conclusions The patient satisfaction scale can be used as a quality assurance tool to evaluate neuropsychological service delivery. Large-scale research is needed to confirm the scale's psychometric properties. Further research may also include a broader perspective on the consumers' experience of neuropsychological services.

Summary of JAYGO mixing and FSM-1 application of castable inhibitor and liner

NASA Technical Reports Server (NTRS)

Evans, Kurt B.

1990-01-01

Two JAYGO planetary mixers (12 and 42 gallon) are being qualified to mix STW5-3224 liner and STW5-3223 castable inhibitor. These mixers are an integral part of a mix process which allows for safe addition of the asbestos component. An essential part of the engineering evaluation (ETP-0347) of these mixers is the generation of static test fire data. Ultimately, these results will help confirm the adequacy of these mixers for production mixing of liner and inhibitor. (These data are not required for qualification of the Certification Test Plan CTP-0125). The details on the mixing, inhibiting, and sling-lining of JAYGO-mixed castable inhibitor and liner which were applied to the FSM-1 segments are presented. The objectives are the following: (1) to document processing events surrounding the JAYO mixing of castable inhibitor and liner, and the subsequent inhibiting and sling lining onto the FSM-1 segments; and (2) to substantiate the measured properties of these JAYGO-mixed materials (rheological and mechanical) and compare these properties to existing production database.

Validation of quantitative and qualitative methods for detecting allergenic ingredients in processed foods in Japan.

PubMed

Sakai, Shinobu; Adachi, Reiko; Akiyama, Hiroshi; Teshima, Reiko

2013-06-19

A labeling system for food allergenic ingredients was established in Japan in April 2002. To monitor the labeling, the Japanese government announced official methods for detecting allergens in processed foods in November 2002. The official methods consist of quantitative screening tests using enzyme-linked immunosorbent assays (ELISAs) and qualitative confirmation tests using Western blotting or polymerase chain reactions (PCR). In addition, the Japanese government designated 10 μg protein/g food (the corresponding allergenic ingredient soluble protein weight/food weight), determined by ELISA, as the labeling threshold. To standardize the official methods, the criteria for the validation protocol were described in the official guidelines. This paper, which was presented at the Advances in Food Allergen Detection Symposium, ACS National Meeting and Expo, San Diego, CA, Spring 2012, describes the validation protocol outlined in the official Japanese guidelines, the results of interlaboratory studies for the quantitative detection method (ELISA for crustacean proteins) and the qualitative detection method (PCR for shrimp and crab DNAs), and the reliability of the detection methods.

Design of an integrated fuel processor for residential PEMFCs applications

NASA Astrophysics Data System (ADS)

Seo, Yu Taek; Seo, Dong Joo; Jeong, Jin Hyeok; Yoon, Wang Lai

KIER has been developing a novel fuel processing system to provide hydrogen rich gas to residential PEMFCs system. For the effective design of a compact hydrogen production system, each unit process for steam reforming and water gas shift, has a steam generator and internal heat exchangers which are thermally and physically integrated into a single packaged hardware system. The newly designed fuel processor (prototype II) showed a thermal efficiency of 78% as a HHV basis with methane conversion of 89%. The preferential oxidation unit with two staged cascade reactors, reduces, the CO concentration to below 10 ppm without complicated temperature control hardware, which is the prerequisite CO limit for the PEMFC stack. After we achieve the initial performance of the fuel processor, partial load operation was carried out to test the performance and reliability of the fuel processor at various loads. The stability of the fuel processor was also demonstrated for three successive days with a stable composition of product gas and thermal efficiency. The CO concentration remained below 10 ppm during the test period and confirmed the stable performance of the two-stage PrOx reactors.

Testing of Co-Fermentation of Poultry Manure and Corn Silage

NASA Astrophysics Data System (ADS)

Jędrczak, Andrzej; Królik, Dariusz; Sądecka, Zofia; Myszograj, Sylwia; Suchowska-Kisielewicz, Monika; Bojarski, Jacek

2014-12-01

The development of the production of poultry meat is connected with an increase in the quantity of the manure. The chemical characteristics predisposes this waste to processing by methane fermentation method. This study investigated the influence of ammonia and volatile fat acids on mesophilic anaerobic digestion of poultry manure. The aim of the studies was: to determine the degree of biodegradation of the poultry manure as well as manure and corn silage mixed in various proportions in the process of mesophilic fermentation, to evaluate the impact of mineral nitrogen and volatile fat acids on the course of fermentation, and to establish optimum proportions of these types of waste. The tests confirmed the positive effect of co-fermentation of poultry manure with corn silage. The most favourable ratio for mixing the substrates is the equal percentage of their dry matter in the mixture. With such waste mixing proportions, the degree of degradation of organic substances contained in the manure amounted to 61.8% and was higher than in the mono-digestion of manure and corn silage.

Indications for laser therapy in diverse models of periodontitis

NASA Astrophysics Data System (ADS)

Kunin, Anatoly A.; Erina, Stanislava V.; Sokolova, Irina A.; Pankova, Svetlana N.; Ippolitov, Yu. A.; Lepechina, L. I.; Malinovskaya, L. A.; Chitrina, L. L.

1996-11-01

Parodontal diseases have an immunological pathogenic mechanism leading to various manifestations and can not be referred to as a common inflammation. The home and foreign research points at active and immunological reaction with the following distraction surrounding tissues of the tooth. Histochemical and biochemical examinations show metabolic disturbances of parodontal tissues. A total sample size of 604 people suffering from average height of chronic generalized parodontitis was examined in the survey. Immunological and histochemical tests were taken before and after a course of laser therapy with the use of helium-neon laser 'YAGODA', an inhibitory and stimulating dosage irradiations and anti-inflammatory dosage irradiations with infrared laser 'UZOR'. We selected a group of patients with the decreased local immunological status on the ground of immunological tests. Histochemical tests shaped the next group with the passive and active forms of parodontitis pathology. The tests data resulted in a method of laser therapy. The investigations confirm that the chronic generalized parodontitis has a shift in tissue immunity of the oral cavity and cell-bound metabolic disturbance of gum epithelium. It is expedient to use the anti-inflammatory dosage irradiations with infrared laser 'UZOR' to correct immunity, and in case of and active process to realize the DNA and RNA synthesis by means of increasing the irradiation with the apparatus 'YAGODA'. The irradiation decreases in case of a passive process.

Relationship between histopathological changes in post partum renal biopsies and renal function tests of African women with early onset pre-eclampsia.

PubMed

Khedun, S M; Naicker, T; Moodley, J

2000-05-01

To improve the diagnostic accuracy of concurrent renal disease in hypertension of pregnancy, biopsy evaluation is essential. In addition, establishing underlying renal disease is important for prognosis on future pregnancies. We therefore designed a study to determine the diagnostic yield of postpartum renal biopsy and the nature and frequency of complications associated with this procedure. Also, to determine relationships, if any, between renal function tests and ultrastructural and histopathological findings. Fifty renal biopsies were performed in the immediate postpartum period in black African women with early onset pre-eclampsia. Each biopsy specimen was placed in a separate container and coded so that sampling was unknown to the electron microscopist. Each biopsy specimen was divided into three parts, and processed and stained for light, fluorescent and transmission electron microscopy using conventional techniques. Renal tissue biopsies were adequate for diagnostic purposes in all cases. There were no complications in any of the 50 patients studied. Ultrastructural examination confirmed the light microscopy findings. In addition the ultrastructural findings showed intramembranous deposits, foot process fusion and mesangial deposits. In 16 patients with normal renal function tests; the biopsies evaluation from these patients showed ultrastructural changes. In the remaining 34 patients with abnormal renal function tests of varying severity; biopsy evaluation from these patients showed both ultrastructural and histopathological changes. Renal biopsy procedure is safe, and ultrastructural and histological findings obtained from postpartum renal biopsies are more informative than the routine renal function tests.