Effect of docosahexaenoic acid and ascorbate on peroxidation of retinal membranes of ODS rats.

PubMed

Wang, Jin-Ye; Sekine, Seiji; Saito, Morio

2003-04-01

Mutant male osteogenic disorder Shionogi (ODS) rats, unable to synthesize ascorbic acid, were fed diets containing a high content of docosahexaenoic acid (DHA) and different amounts of ascorbic acid, to study the effect of DHA on peroxidative susceptibility of the retina and possible antioxidant action of ascorbic acid. ODS rats were fed from 7 weeks of age with diets containing high DHA (6.4% of total energy). A control group received a diet high in linoleic acid. The diets also contained varying amounts of ascorbic acid. Fatty acid compositions and phospholipid hydroperoxides in rod outer segment (ROS) membranes, and retinal ascorbic acid were analyzed. DHA in ROS membranes was significantly increased in rats fed high DHA, compared with the linoleic acid diet. Levels of phospholipid hydroperoxides in the DHA-fed rats were significantly higher than the linoleic acid-fed rats. Ascorbic acid supplementation did not suppress the phospholipid hydroperoxide levels after a high DHA diet, even when the supplement increased the content of retinal ascorbic acid. In conclusion, high DHA feeding induced a marked increase of phospholipid hydroperoxides in ROS membranes of ODS rats. Supplementation of ascorbic acid did not reverse this increase.

Grape juice, berries and walnuts affect brain aging and behavior

USDA-ARS?s Scientific Manuscript database

Numerous studies have indicated that individuals consuming a diet containing high amounts of fruits and vegetables exhibit fewer age-related diseases such as Alzheimer Disease (AD). A recent report has indicated that individuals who consumed a diet containing 2.5 servings of fruit and vegetables/day...

Whole Grains Contribute Only a Small Proportion of Dietary Fiber to the U.S. Diet.

PubMed

Kranz, Sibylle; Dodd, Kevin W; Juan, Wen Yen; Johnson, LuAnn K; Jahns, Lisa

2017-02-17

Dietary fiber (DF), found in whole fruits, vegetables, and whole grains (WG), is considered a nutrient of concern in the US diet and increased consumption is recommended. The present study was designed to highlight this critical importance of the difference between WG, high-fiber WG, and sources of fiber that are not from WG. The study is based on the two-day diets reported consumed by the nationally representative sample of Americans participating in What We Eat In America, the dietary component of the National Health and Nutrition Examination Survey from 2003-2010. Foods consumed were classified into tertiles of DF and WG and the contribution of fiber by differing levels of WG content were examined. Foods containing high amounts of WG and DF only contributed about 7% of total fiber intake. Overall, grain-based foods contributed 54.5% of all DF consumed. Approximately 39% of DF came from grain foods that contained no WG, rather these foods contained refined grains, which contain only small amounts of DF but are consumed in large quantities. All WG-containing foods combined contributed a total of 15.3% of DF in the American diet. Thus, public health messaging needs to be changed to specifically encourage consumption of WG foods with high levels of DF to address both recommendations.

[A new method for determining the body composition with the aid of a displacement balance and low-pressure volumetric analysis (author's transl)].

PubMed

Schmid, P; Schlick, W; Irsigler, K

1976-01-09

A new method for determination of the specific weight of the gas-free human body is presented. Volume measurement is facilitated by extremely precise scales, by means of which a well-defined amount of water which was removed from a "patient container" is weighed. After the test subject has entered the container and is standing up to the neck in water, the container is closed. The combined gas volume consisting of the subject's lung volume, his intestinal gas and the air around his head is measured by lowering the pressure by an exactly-defined amount. This is done by opening a valve at the bottom of the container, which results in the outflow of a certain amount of water, the volume of which corresponds to the volume expansion inside the container. The gas volume prior to expansion can then be calculated by application of the gas laws. The advantages of this measuring device are its relatively small size, the high precision and the fact that the procedure is not unpleasant for the subject, as the head is not submerged under water.

Fresh from the Ornamental Garden: Hips of Selected Rose Cultivars Rich in Phytonutrients.

PubMed

Cunja, Vlasta; Mikulic-Petkovsek, Maja; Weber, Nika; Jakopic, Jerneja; Zupan, Anka; Veberic, Robert; Stampar, Franci; Schmitzer, Valentina

2016-02-01

Morphological parameters (size, weight, color), the content of sugars, organic acids, lycopene, β-carotene, and phenolics were determined in hips of Rosa canina (RCA), Rosa sweginzowii (RSW), Rosa rugosa (RUG), and selected ornamental Rosa cultivars Fru Dagmar Hastrup (FDH), Repandia (REP), Veilchenblau (RVB), Aloha (RAL), Bonica (BON), and Golden Gate (RGG). Although traditionally used RCA hips contained the highest amount of cyanidin-3-glucoside (83 μg/g DW) and were the reddest (h° = 17.5), they did not stand out in other analyzed parameters. RGG climber had the biggest hips (8.86 g), which also contained highest sugar levels (50.9 g/100 g DW). RAL stood out as the cultivar rich in organic acids (33.9 g/100 g DW), mainly because of high quinic acid content (17.6 g/100g DW). FDH and RSW hips were characterized by particularly high ascorbic acid levels (4325 mg/100 g DW and 4711 mg/100 g DW). Other ornamental cultivars contained low amounts of ascorbic acid compared to the analyzed species. The phenolic profile was species/cultivars-specific. The greatest diversity of phenolic compounds was detected in RUG and FDH hips (55 and 54 different tentatively identified compounds with HPLC/MS). Flavanols represented the main phenolic class in most of the investigated species/cultivars and RGG hips contained the highest amount of catechin and proanthocyandin derivatives (15855 μg/g DW). Altogether RAL hips contained the highest quantity of phenolics (44746 μg/g DW) mainly due to high levels of hydrolysable tannins compared to other species/cultivars. Although small, hips of BON and REP were most abundant regarding β-carotene and lycopene content, respectively. © 2016 Institute of Food Technologists®

High Throughput Experimental Materials Database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakutayev, Andriy; Perkins, John; Schwarting, Marcus

The mission of the High Throughput Experimental Materials Database (HTEM DB) is to enable discovery of new materials with useful properties by releasing large amounts of high-quality experimental data to public. The HTEM DB contains information about materials obtained from high-throughput experiments at the National Renewable Energy Laboratory (NREL).

[Nutrition and bone health. Soybean and soy foods, and bone health].

PubMed

Kubota, Megumi; Shimizu, Hirotoshi

2009-10-01

Soybean and various types of soy products, such as natto, tofu, miso, and soy sauce, have long been consumed in Japan. Soybean, a rich source of plant proteins, contains a relatively high amount of calcium as well as being an important source of isoflavones, a group of substances whose chemical structure is similar to that of estrogen. Natto, fermented soybeans, contains vitamin K, which is involved in the activation of osteocalcin. For bone health and osteoporosis prevention in Japanese, it is thus beneficial to consume adequate amounts of soybean and soy products on a daily basis.

A geologic assessment of potential lunar ores

NASA Technical Reports Server (NTRS)

Mckay, D. S.; Williams, R. J.

1979-01-01

Although bulk lunar soil is not a suitable feedstock for extracting metals, certain minerals such as anorthite and ilmenite can be separated and concentrated. These minerals can be considered as potential ores of aluminum, silicon, titanium, andiron. A separation and metal extraction plant could also extract large amounts of oxygen and perhaps hydrogen from these minerals. Anorthie containing 19 percent aluminum and 20 percent silicon can be concentrated from some highland soils where it is present in amounts up to 60 percent. Ilmenite containing 32 percent titanium and 37 percent iron can be concentrated from some mare soils where it is present in amounts up to 10 percent. The ideal mining site would be located at the boundary between a high-titanium mare and a high-aluminum highlands. Such area may exist around the rims of some eastern maria, particularly Tranquilitatis. A location on Earth with raw materials as described above would be considered an economically valuable ore deposit if conventional terrestrial resources were not available.

The Effects of a Nutrient-Enriched Bar on Host Defense Mechanisms and Immunogenicity of Hepatitis A Vaccine During US Army Ranger Training

DTIC Science & Technology

2000-02-01

from casein and soy and carbohydrates from honey, maltodextrin, and high fructose corn syrup . The treatment bar contained fructooligosaccharide (an...nutritional deprivation and immune dysregulation as measured by a high rate of skin DTH anergy among trainees (58). However, even with severe energy...same amount of energy was included in the placebo bar to prevent any confounding factors. The bars contained similar proteins ( high biologic value

Ziegler-Natta Catalyst Based on MgCl₂/Clay/ID/TiCl₄ for the Synthesis of Spherical Particles of Polypropylene Nanocomposites.

PubMed

Cardoso, Renata da Silva; Oliveira, Jaqueline da Silva; Ramis, Luciana Bortolin; Marques, Maria de Fátima V

2018-07-01

In the present work, we have designed MgCl2/clay/internal donor (ID)/TiCl4 based bisupported Ziegler-Natta catalysts containing varying amounts of organoclay (montmorillonite) in order to synthesize spherical particles of polypropylene/clay nanocomposites (PCN). The organoclay was introduced into the catalyst support formulation and PCN was obtained using the in situ polymerization technique. Decreasing the reaction time, it was possible to obtain nanocomposites with high concentrations of clay (masterbatches). Micrographs of SEM confirmed the spherical morphology of the catalysts. In addition, XRD patterns show that the active sites for polymerization were inserted in the clay galleries. The catalytic performance was evaluated in slurry propylene polymerization using triethylaluminium as cocatalyst and silane as external electron donor at 70 °C, 4 bar, and different reaction times. The PCNs obtained containing different clay amounts were characterized by X-ray diffraction, thermal analyses, transmission electronic microscopy, and extractables in heptane. The results revealed that the synthesized PP/clay particles were also spherical showing that the morphological control is possible even using catalysts containing high amounts of clay. The PCN presented high degradation temperature (459 °C). The XRD peak related to the clay interlamellar distance has shifted to lower angles, and TEM images confirmed the formation of exfoliated/intercalated clay on the PP matrix and absence of microparticles of clay.

Mitigation of oxidative stress and inflammatory signaling by fruit and walnut polyphenols: implications for cognitive aging

USDA-ARS?s Scientific Manuscript database

Numerous epidemiological studies have indicated that individuals who consume a diet containing high amounts of fruits and vegetables exhibit fewer age-related diseases such as Alzheimer Disease (AD). A recent report has indicated that individuals who consumed a diet containing 2.5 servings of fruit ...

Ruminal fermentation of anti-methanogenic nitrate- and nitro-containing forages in vitro

USDA-ARS?s Scientific Manuscript database

Nitrate, 3-nitro-1-propionic acid (NPA), and 3-nitro-1-propanol (NPOH) can accumulate in forages and be poisonous to animals if fed at high enough amounts. These chemicals are also recognized as potent anti-methanogenic compounds, but plants naturally containing these chemicals have been studied li...

In vitro corrosion behaviour and microhardness of high-copper amalgams with platinum and indium.

PubMed

Ilikli, B G; Aydin, A; Işimer, A; Alpaslan, G

1999-02-01

Samples prepared from Luxalloy, GS-80, Permite-C and Logic and polished after 24 h by traditional methods were stored in polypropylene tubes containing phosphate-buffered saline solutions (pH 3.5 and 6.5) and distilled water. The amounts of mercury, silver, tin, copper, zinc, platinum and indium in the test solutions were determined at the first, second, eighth, 52nd and 78th week by atomic absorption spectrometry. At the end of the eighth week the amalgam samples were removed from solutions and evaluated by Rockwell Super Scial Microhardness tester. Statistically significant low amounts of metal ions were measured for Permite-C containing indium and Logic containing platinum. The microhardness test results showed that there were statistically significant increases in the microhardness of Permite-C and Logic. As a result it was shown that the amalgam samples were affected from corrosion conditions to different degrees. Sample of the Logic group that was stored in distilled water, showed smoother surface properties than other amalgam samples containing high copper. However, it was observed that samples of Permite-C group had the smoothest surface properties.

Histoplasmosis

MedlinePlus

... by the fungus. Soil that contains bird or bat droppings may have larger amounts of this fungus. ... by reducing exposure to dust in chicken coops, bat caves, and other high-risk locations. Wear masks ...

Ingestion of onion soup high in quercetin inhibits platelet aggregation and essential components of the collagen-stimulated platelet activation pathway in man: a pilot study.

PubMed

Hubbard, Gary P; Wolffram, Siegfried; de Vos, Ric; Bovy, Arnaud; Gibbins, Jonathan M; Lovegrove, Julie A

2006-09-01

Epidemiological data suggest that those who consume a diet rich in quercetin-containing foods may have a reduced risk of CVD. Furthermore, in vitro and ex vivo studies have observed the inhibition of collagen-induced platelet activation by quercetin. The aim of the present study was to investigate the possible inhibitory effects of quercetin ingestion from a dietary source on collagen-stimulated platelet aggregation and signalling. A double-blind randomised cross-over pilot study was undertaken. Subjects ingested a soup containing either a high or a low amount of quercetin. Plasma quercetin concentrations and platelet aggregation and signalling were assessed after soup ingestion. The high-quercetin soup contained 69 mg total quercetin compared with the low-quercetin soup containing 5 mg total quercetin. Plasma quercetin concentrations were significantly higher after high-quercetin soup ingestion than after low-quercetin soup ingestion and peaked at 2.59 (sem 0.42) mumol/l. Collagen-stimulated (0.5 mug/ml) platelet aggregation was inhibited after ingestion of the high-quercetin soup in a time-dependent manner. Collagen-stimulated tyrosine phosphorylation of a key component of the collagen-signalling pathway via glycoprotein VI, Syk, was significantly inhibited by ingestion of the high-quercetin soup. The inhibition of Syk tyrosine phosphorylation was correlated with the area under the curve for the high-quercetin plasma profile. In conclusion, the ingestion of quercetin from a dietary source of onion soup could inhibit some aspects of collagen-stimulated platelet aggregation and signalling ex vivo. This further substantiates the epidemiological data suggesting that those who preferentially consume high amounts of quercetin-containing foods have a reduced risk of thrombosis and potential CVD risk.

How much sugar is hidden in drinks marketed to children? A survey of fruit juices, juice drinks and smoothies

PubMed Central

Boulton, Jane; Hashem, Kawther M; Jenner, Katharine H; Lloyd-Williams, Ffion; Bromley, Helen; Capewell, Simon

2016-01-01

Objective To investigate the amount of sugars in fruit juices, juice drinks and smoothies (FJJDS) marketed to children. Design We surveyed the sugars content (per 100 ml and standardised 200 ml portion) of all FJJDS sold by seven major UK supermarkets (supermarket own and branded products). Only products specifically marketed towards children were included. We excluded sports drinks, iced teas, sugar-sweetened carbonated drinks and cordials as being not specifically marketed towards children. Results We identified 203 fruit juices (n=21), juice drinks (n=158) and smoothies (n=24) marketed to children. Sugars content ranged from 0 to 16 g/100 ml. The mean sugars content was 7.0 g/100 ml, but among the 100% fruit juice category, it was 10.7 g/100 ml. Smoothies (13.0 g/100 ml) contained the highest amounts of sugars and juice drinks (5.6 g/100 ml) contained the lowest amount. 117 of the 203 FJJDS surveyed would receive a Food Standards Agency ‘red’ colour-coded label for sugars per standardised 200 ml serving. Only 63 FJJDS would receive a ‘green’ colour-coded label. 85 products contained at least 19 g of sugars—a child's entire maximum daily amount of sugars. 57 products contained sugar (sucrose), 65 contained non-caloric sweeteners and five contained both. Seven products contained glucose-fructose syrup. Conclusions The sugars content in FJJDS marketed to children in the UK is unacceptably high. Manufacturers must stop adding unnecessary sugars and calories to their FJJDS. PMID:27009146

How much sugar is hidden in drinks marketed to children? A survey of fruit juices, juice drinks and smoothies.

PubMed

Boulton, Jane; Hashem, Kawther M; Jenner, Katharine H; Lloyd-Williams, Ffion; Bromley, Helen; Capewell, Simon

2016-03-23

To investigate the amount of sugars in fruit juices, juice drinks and smoothies (FJJDS) marketed to children. We surveyed the sugars content (per 100 ml and standardised 200 ml portion) of all FJJDS sold by seven major UK supermarkets (supermarket own and branded products). Only products specifically marketed towards children were included. We excluded sports drinks, iced teas, sugar-sweetened carbonated drinks and cordials as being not specifically marketed towards children. We identified 203 fruit juices (n=21), juice drinks (n=158) and smoothies (n=24) marketed to children. Sugars content ranged from 0 to 16 g/100 ml. The mean sugars content was 7.0 g/100 ml, but among the 100% fruit juice category, it was 10.7 g/100 ml. Smoothies (13.0 g/100 ml) contained the highest amounts of sugars and juice drinks (5.6 g/100 ml) contained the lowest amount. 117 of the 203 FJJDS surveyed would receive a Food Standards Agency 'red' colour-coded label for sugars per standardised 200 ml serving. Only 63 FJJDS would receive a 'green' colour-coded label. 85 products contained at least 19 g of sugars-a child's entire maximum daily amount of sugars. 57 products contained sugar (sucrose), 65 contained non-caloric sweeteners and five contained both. Seven products contained glucose-fructose syrup. The sugars content in FJJDS marketed to children in the UK is unacceptably high. Manufacturers must stop adding unnecessary sugars and calories to their FJJDS. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Vitamin B12-Containing Plant Food Sources for Vegetarians

PubMed Central

Watanabe, Fumio; Yabuta, Yukinori; Bito, Tomohiro; Teng, Fei

2014-01-01

The usual dietary sources of Vitamin B12 are animal-derived foods, although a few plant-based foods contain substantial amounts of Vitamin B12. To prevent Vitamin B12 deficiency in high-risk populations such as vegetarians, it is necessary to identify plant-derived foods that contain high levels of Vitamin B12. A survey of naturally occurring plant-derived food sources with high Vitamin B12 contents suggested that dried purple laver (nori) is the most suitable Vitamin B12 source presently available for vegetarians. Furthermore, dried purple laver also contains high levels of other nutrients that are lacking in vegetarian diets, such as iron and n-3 polyunsaturated fatty acids. Dried purple laver is a natural plant product and it is suitable for most people in various vegetarian groups. PMID:24803097

Transformation of 5-O-caffeoylquinic acid in blueberries during high-temperature processing.

PubMed

Dawidowicz, Andrzej L; Typek, Rafal

2014-11-12

Chlorogenic acid (CQA), an ester of caffeic with quinic acid, is a natural compound found in a wide array of plants. Although coffee beans are most frequently mentioned as plant products remarkably rich in CQAs, their significant amounts can also be found in many berries, for example, blueberries. This paper shows and discusses the thermal stability of the main CQA representative, that is, 5-O-caffeoylquinic acid (5-CQA), during high-temperature processing of blueberries (as in the production of blueberry foods) in systems containing sucrose in low and high concentration. It has been found that up to 11 components (5-CQA derivatives and its reaction product with water) can be formed from 5-CQA during the processing of blueberries. Their formation speed depends on the sucrose concentration in the processed system, which has been confirmed in the artificial system composed of 5-CQA water solution containing different amounts of the sugar.

Hydroisomerization of n-Hexane Using Acidified Metal-Organic Framework and Platinum Nanoparticles.

PubMed

Sabyrov, Kairat; Jiang, Juncong; Yaghi, Omar M; Somorjai, Gabor A

2017-09-13

Exceptionally high surface area and ordered nanopores of a metal-organic framework (MOF) are exploited to encapsulate and homogeneously disperse a considerable amount of phosphotungstic acid (PTA). When combined with platinum nanoparticles positioned on the external surface of the MOF, the construct shows a high catalytic activity for hydroisomerization of n-hexane, a reaction requiring hydrogenation/dehydrogenation and moderate to strong Brønsted acid sites. Characterization of the catalytic activity and acidic sites as a function of PTA loading demonstrates that both the concentration and strength of acidic sites are highest for the catalyst with the largest amount of PTA. The MOF construct containing 60% PTA by weight produces isoalkanes with 100% selectivity and 9-fold increased mass activity as compared to a more traditional aluminosilicate catalyst, further demonstrating the capacity of the MOF to contain a high concentration of active sites necessary for the isomerization reaction.

29 CFR 1910.1030 - Bloodborne pathogens.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated representative. Engineering controls means controls (e.g., sharps disposal containers, self...-volume or high concentration production of HIV or HBV. Regulated Waste means liquid or semi-liquid blood... research-laboratory-scale amounts of HIV or HBV. Research laboratories may produce high concentrations of...

Whole Grains Contribute Only a Small Proportion of Dietary Fiber to the U.S. Diet

PubMed Central

Kranz, Sibylle; Dodd, Kevin W.; Juan, Wen Yen; Johnson, LuAnn K.; Jahns, Lisa

2017-01-01

Dietary fiber (DF), found in whole fruits, vegetables, and whole grains (WG), is considered a nutrient of concern in the US diet and increased consumption is recommended. The present study was designed to highlight this critical importance of the difference between WG, high-fiber WG, and sources of fiber that are not from WG. The study is based on the two-day diets reported consumed by the nationally representative sample of Americans participating in What We Eat In America, the dietary component of the National Health and Nutrition Examination Survey from 2003–2010. Foods consumed were classified into tertiles of DF and WG and the contribution of fiber by differing levels of WG content were examined. Foods containing high amounts of WG and DF only contributed about 7% of total fiber intake. Overall, grain-based foods contributed 54.5% of all DF consumed. Approximately 39% of DF came from grain foods that contained no WG, rather these foods contained refined grains, which contain only small amounts of DF but are consumed in large quantities. All WG-containing foods combined contributed a total of 15.3% of DF in the American diet. Thus, public health messaging needs to be changed to specifically encourage consumption of WG foods with high levels of DF to address both recommendations. PMID:28218657

Identification and HPLC quantitation of the sulfides and dialk(en)yl thiosulfinates in commercial garlic products.

PubMed

Lawson, L D; Wang, Z J; Hughes, B G

1991-08-01

The content of dialk(en)yl thiosulfinates, including allicin, and their degradation products has been determined by high performance liquid chromatography (HPLC), using the respective determined extinction coefficients, for a number of commercially available garlic products. Quantitation has been achieved for the thiosulfinates; diallyl, methyl allyl, and diethyl mono-, di-, tri-, tetra-, penta-, and hexasulfides; the vinyldithiins; and (E)- and (Z)-ajoene. The thiosulfinates were found to be released only from garlic cloves and garlic powder products. The vinyldithiins and ajoenes were found only in products containing garlic macerated in vegetable oil. The diallyl, methyl allyl, and dimethyl sulfide series were the exclusive constituents found in products containing the oil of steam-distilled garlic. Typical steam-distilled garlic oil products contained about the same amount of total sulfur compounds as total thiosulfinates released from freshly homogenized garlic cloves; however, oil-macerated products contained only 20% of that amount, while garlic powder products varied from 0 to 100%. Products containing garlic powder suspended in a a gel or garlic aged in aqueous alcohol did not contain detectable amounts of these non-ionic sulfur compounds. A comparison of several brands of each type of garlic product revealed a large range in content (4-fold for oil-macerates and 33-fold for steam-distilled garlic oils), indicating the importance of analysis before garlic products are used for clinical investigations or commercial distribution.

Simplified Production of Organic Compounds Containing High Enantiomer Excesses

NASA Technical Reports Server (NTRS)

Cooper, George W. (Inventor)

2015-01-01

The present invention is directed to a method for making an enantiomeric organic compound having a high amount of enantiomer excesses including the steps of a) providing an aqueous solution including an initial reactant and a catalyst; and b) subjecting said aqueous solution simultaneously to a magnetic field and photolysis radiation such that said photolysis radiation produces light rays that run substantially parallel or anti-parallel to the magnetic field passing through said aqueous solution, wherein said catalyst reacts with said initial reactant to form the enantiomeric organic compound having a high amount of enantiomer excesses.

Y2O3:Eu phosphor particles prepared by spray pyrolysis from a solution containing citric acid and polyethylene glycol

NASA Astrophysics Data System (ADS)

Roh, H. S.; Kang, Y. C.; Park, H. D.; Park, S. B.

Y2O3:Eu phosphor particles were prepared by large-scale spray pyrolysis. The morphological control of Y2O3:Eu particles in spray pyrolysis was attempted by adding polymeric precursors to the spray solution. The effect of composition and amount of polymeric precursors on the morphology, crystallinity and photoluminescence characteristics of Y2O3:Eu particles was investigated. Particles prepared from a solution containing polyethylene glycol (PEG) with an average molecular weight of 200 had a hollow structure, while those prepared from solutions containing adequate amounts of citric acid (CA) and PEG had a spherical shape, filled morphology and clean surfaces after post-treatment at high temperature. Y2O3:Eu particles prepared from an aqueous solution with no polymeric precursors had a hollow structure and rough surfaces after post-treatment. The phosphor particles prepared from solutions with inadequate amounts of CA and/or PEG also had hollow and/or fragmented structures. The particles prepared from the solution containing 0.3 M CA and 0.3 M PEG had the highest photoluminescence emission intensity, which was 56% higher than that of the particles prepared from aqueous solution without polymeric precursors.

Looking for High Quality Accreditation in Higher Education in Colombia

ERIC Educational Resources Information Center

Pérez Gama, Jesús Alfonso; Vega Vega, Anselmo

2017-01-01

We look for the High Quality Accreditation of tertiary education in two ways: one, involving large amount of information, including issues such as self-assessment, high quality, statistics, indicators, surveys, and field work (process engineering), during several periods of time; and the second, in relation to the information contained there about…

NMR of samples containing metal foils.

PubMed

Xiong, J; Lock, H; Tao, T; Keeler, C; Maciel, G E

1999-07-01

By using spool configurations of a sample containing aluminum foil, in which the axis of the spool is collinear with the RF coil axis, one can obtain high-quality 13C NMR spectra of static samples of organic material attached to the aluminum foil. By combining such a spool configuration (or, alternatively, analogous samples containing equivalent amounts of fine aluminum powder) with the magic-angle hopping (MAH) technique, one can achieve a high degree of isotropic averaging of the 13C spectrum. This opens to NMR techniques the study of a variety of samples containing macroscopic pieces of metal foils, e.g., thin films deposited on metal foils and electrochemical systems with species adsorbed on metal-foil electrodes.

Effects of pressure and temperature on sintering of Cr-doped Al2O3 by pulsed electric current sintering process

NASA Astrophysics Data System (ADS)

Dang, K. Q.; Nanko, M.

2011-03-01

The aluminium oxide crystal, Al2O3, which contains a small amount of chromium, Cr, is called ruby. Pulsed electric current sintering (PECS) was applied to sinter ruby polycrystals. Cr2O3-Al2O3 powder mixture prepared by drying an aqueous slurry containing amounts of Al2O3 and Cr(NO3)3 was consolidated by PECS process. The PECS process was performed in vacuum at sintering temperature raging from 1100 to 1300°C with heating rate of 2 K/min under applied uniaxial pressure varied from 40 to 100 MPa. This study found that highly densified and transparent Cr-doped Al2O3 can be obtained by the PECS process with the high applied pressure at sintering temperature of 1200°C.

Safety assessment of a natural tomato oleoresin containing high amounts of Z-isomers of lycopene prepared with supercritical carbon dioxide.

PubMed

Honda, Masaki; Higashiura, Takuma; Fukaya, Tetsuya

2017-02-01

Z-isomers of lycopene, which are abundantly present in processed tomato products, are more bioavailable than (all-E)-lycopene found predominantly in raw tomatoes. Despite extensive studies on the bioavailability and biological activities of Z-isomers of lycopene, detailed studies on their safety and toxicology are limited. The geno-, acute and subacute toxicities of tomato oleoresin that contained high amounts of lycopene Z-isomers (10.9% lycopene with 66.3% Z-isomer content) and had been prepared with supercritical carbon dioxide were investigated. The oleoresin was non-mutagenic in the Ames test with and without metabolic activation (S9 mix). The medial lethal dose (LD 50 ) of the oleoresin in rats, as determined by a single-dose oral test, was more than 5000 mg kg body weight -1 (bw) [361 mg (Z)-lycopene kg bw -1 ]. In the 4-week repeated-dose oral toxicity test, rats were administered oleoresin at 4500 mg kg -1 day -1 [325 mg (Z)-lycopene kg bw -1 day -1 ]. There were no clinically significant changes with respect to vital signs, physical examination outcomes and laboratory test values during the test period. Based on our findings and as supported by its long history of consumption, tomato oleoresin that contains high amounts of Z-isomers of lycopene prepared with supercritical carbon dioxide can be considered as safe for human consumption. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Sorption Isotherm of Southern Yellow Pine-High Density Polyethylene Composites.

PubMed

Liu, Feihong; Han, Guangping; Cheng, Wanli; Wu, Qinglin

2015-01-20

Temperature and relative humidity (RH) are two major external factors, which affect equilibrium moisture content (EMC) of wood-plastic composites (WPCs). In this study, the effect of different durability treatments on sorption and desorption isotherms of southern yellow pine (SYP)-high density polyethylene (HDPE) composites was investigated. All samples were equilibriumed at 20 °C and various RHs including 16%, 33%, 45%, 66%, 75%, 85%, 93%, and100%. EMCs obtained from desorption and absorption for different WPC samples were compared with Nelson's sorption isotherm model predictions using the same temperature and humidity conditions. The results indicated that the amount of moisture absorbed increased with the increases in RH at 20 °C. All samples showed sorption hysteresis at a fixed RH. Small difference between EMC data of WPC samples containing different amount of ultraviolet (UV) stabilizers were observed. Similar results were observed among the samples containing different amount of zinc borate (ZB). The experimental data of EMCs at various RHs fit to the Nelson's sorption isotherm model well. The Nelson's model can be used to predicate EMCs of WPCs under different RH environmental conditions.

Sorption Isotherm of Southern Yellow Pine—High Density Polyethylene Composites

PubMed Central

Liu, Feihong; Han, Guangping; Cheng, Wanli; Wu, Qinglin

2015-01-01

Temperature and relative humidity (RH) are two major external factors, which affect equilibrium moisture content (EMC) of wood-plastic composites (WPCs). In this study, the effect of different durability treatments on sorption and desorption isotherms of southern yellow pine (SYP)-high density polyethylene (HDPE) composites was investigated. All samples were equilibriumed at 20 °C and various RHs including 16%, 33%, 45%, 66%, 75%, 85%, 93%, and100%. EMCs obtained from desorption and absorption for different WPC samples were compared with Nelson’s sorption isotherm model predictions using the same temperature and humidity conditions. The results indicated that the amount of moisture absorbed increased with the increases in RH at 20 °C. All samples showed sorption hysteresis at a fixed RH. Small difference between EMC data of WPC samples containing different amount of ultraviolet (UV) stabilizers were observed. Similar results were observed among the samples containing different amount of zinc borate (ZB). The experimental data of EMCs at various RHs fit to the Nelson’s sorption isotherm model well. The Nelson’s model can be used to predicate EMCs of WPCs under different RH environmental conditions. PMID:28787943

Collection of Pyrethroids in Water and Sediment Matrices: Development and Validation of a Standard Operating Procedure

USGS Publications Warehouse

Hladik, Michelle; Orlando, James L.; Kuivila, Kathryn

2009-01-01

Loss of pyrethroid insecticides onto surfaces during sample collection can confound the interpretation of analytical and toxicity test results. Sample collection devices, container materials, and water matrix composition have a significant influence on the association of pyrethroids to container walls, which can be as high as 50 percent. Any sample collection method involving transfer through multiple containers or pieces of equipment increases the potential for pyrethroid loss. This loose 'surface-association' with container walls can be reversed through agitation. When sampling water matrices with pumps or autosamplers, no pyrethroids were lost as long as the water was moving continuously through the system. When collecting water matrices in containers, the material with the least amount of pyrethroid sorption is as follows: glass less than (<) plastic less than (<) Teflon. Additionally, pyrethroids were easier to re-suspend from the glass container walls. Since the amount of surface-association is proportional to the ratio of volume-to-contact-area of the sample, taking larger-volume field samples (greater than 3 liters) reduced pyrethroid losses to less than 10 percent. The amount of surface-association cannot be predicted easily because of the dependence on water matrix composition; samples with higher dissolved organic carbon or suspended-sediment concentrations were observed to have lower percent loss. Sediment samples were not affected by glass-container sorption (the only containers tested). Standardized sample-collection protocols are critical to yield accurate pyrethroid concentrations for assessment of potential effects, and have been summarized in an accompanying standard operating procedure.

Choline and Inositol Distribution in Algae and Fungi1

PubMed Central

Ikawa, Miyoshi; Borowski, Paul T.; Chakravarti, Ashima

1968-01-01

Inositol and choline were present in varying amounts among the species of Rhodophyta, Phaeophyta, Chlorophyta, and Euglenophyta examined. However, in the two members of the order Fucales (division Phaeophyta) examined, no detectable amounts of choline were found. In contrast, the species of Cyanophyta examined contained no detectable amounts of either choline or inositol. All species of the fungal classes Phycomyceteae, Ascomyceteae, and Basidiomyceteae collected contained both inositol and choline in varying amounts. The red, brown, and blue-green algae usually contained much less inositol and choline than do plant and animals sources, but the fungi and the algae Chlorella and Euglena contained amounts comparable to those present in plant sources. PMID:5647522

Sewage treatment method

DOEpatents

Fassbender, Alex G.

1995-01-01

The invention greatly reduces the amount of ammonia in sewage plant effluent. The process of the invention has three main steps. The first step is dewatering without first digesting, thereby producing a first ammonia-containing stream having a low concentration of ammonia, and a second solids-containing stream. The second step is sending the second solids-containing stream through a means for separating the solids from the liquid and producing an aqueous stream containing a high concentration of ammonia. The third step is removal of ammonia from the aqueous stream using a hydrothermal process.

URANIUM COMPOSITIONS

DOEpatents

Allen, N.P.; Grogan, J.D.

1959-05-12

This patent relates to high purity uranium alloys characterized by improved stability to thermal cycling and low thermal neutron absorption. The high purity uranium alloy contains less than 0.1 per cent by weight in total amount of any ore or more of the elements such as aluminum, silicon, phosphorous, tin, lead, bismuth, niobium, and zinc.

Leaching of diethylhexyl phthalate from polyvinyl chloride bags into intravenous etoposide solution.

PubMed

Demoré, B; Vigneron, J; Perrin, A; Hoffman, M A; Hoffman, M

2002-04-01

To compare the release of diethylhexyl phthalate (DEHP) from polyvinyl chloride (PVC) bags from four different manufacturers into intravenous etoposide solutions. Etoposide solutions, 0.4 mg/mL, containing the vehicle polysorbate 80 were prepared in 5% dextrose or 0.9% sodium chloride injection PVC bags and stored at room temperature for 24 h. DEHP content was analysed by high-performance liquid chromatography. Substantial amounts of DEHP (up to 20 microg/mL at room temperature) leached into the etoposide solutions. However, no significant differences were found in the amounts of DEHP leached into the etoposide infusion solutions prepared using either 5% dextrose or 0.9% sodium chloride injection and stored in the four different containers. To minimize patient exposure o DEHP, etoposide solutions should ideally be stored in a glass or polyolefin container.

Tumor promotion by dietary fat in azoxymethane-induced colon carcinogenesis in female F344 rats: influence of amount and source of dietary fat.

PubMed

Reddy, B S; Maeura, Y

1984-03-01

The promoting effect of dietary corn oil (CO), safflower oil (SO), olive oil (OO), coconut oil (CC), and medium-chain triglycerides (MCT) on azoxymethane (AOM)-induced colon tumors was studied in female F344 rats. The animals were fed low-fat diets containing 5% CO, 5% SO, or 5% OO 2 weeks before, during, and 1 week after sc injection of 20 mg AOM/kg body weight. One week after the AOM treatment, groups of animals were transferred to high-fat diets containing 23.52% CO, 23.52% SO, 23.52% OO, and 23.52% CC, or 5.88% CO + 17.64% MCT; the remaining animals were continued on 5% fat diets. All animals were fed these diets until the termination of the experiment. Body weights and intakes of calories, protein, and micronutrients were comparable among the various dietary groups. The incidence of colon tumors was increased in rats fed diets containing high-CO and high-SO compared to those fed low-CO and low-SO diets, whereas the diets containing high OO, CC, or MCT had no promoting effect on colon tumor incidence. There was a significant increase in the excretion of fecal deoxycholic acid, lithocholic acid, and 12-ketolithocholic acid in animals fed the high-CO and high-SO diets and no difference in these secondary bile acids excretion in animals fed the high-OO and high-CC diets compared to those animals fed their respective 5% fat diets. This study thus indicates that not only the amount of dietary fat but also the fatty acid composition (type) of fat are important factors in the determination of the promoting effect in colon carcinogenesis.

Impact of composting strategies on the degradation of nonylphenol in sewage sludge.

PubMed

Zheng, Guodi; Chen, Tongbin; Yu, Jie; Gao, Ding; Shen, Yujun; Niu, Mingjie; Liu, Hongtao

2015-12-01

Nonylphenol can be present in sewage sludge, and this can limit the use of the sewage sludge to amend soil. Composting is one of the most efficient and economical methods of making sewage sludge stable and harmless. The nonylphenol degradation rates during composting with added bulking agents and with aeration applied were studied. Three organic bulking agents (sawdust, corn stalk, and mushroom residue) were added to sewage sludge, and the effects of the bulking agents used and the amount added on nonylphenol degradation were determined. The highest apparent nonylphenol degradation rate (71.6%) was found for sewage sludge containing 20% mushroom residue. The lowest apparent nonylphenol degradation rate (22.5%) was found for sewage sludge containing 20% sawdust. The temperature of the composting pile of sewage sludge containing 20% sawdust became too high for nonylphenol to be efficiently degraded, and the apparent nonylphenol degradation rate was lower than was found for sewage sludge containing 10% sawdust. Increasing the ventilating time from 5 to 15 min increased the apparent nonylphenol degradation rate from 19.7 to 41.6%. Using appropriate aerobic conditions facilitates the degradation of nonylphenol in sewage sludge, decreasing the risks posed by sewage sludge applied to land. Adding too much of a bulking agent can decrease the amount of the nonylphenol degraded. Increasing the ventilating time and the amount of air supplied can increase the amount of nonylphenol degraded even if doing so causes the composting pile temperature to remain low.

Evidence for komatiite-type lavas on Mars from Phobos ISM data and other observations

NASA Technical Reports Server (NTRS)

Reyes, David P.; Christensen, Philip R.

1994-01-01

Data from the Phobos 2 Imaging Spectrometer for Mars (ISM), compiled by Mustard et al. (1993), and other observations support the existence of komatiitic lavas on Mars. Mustard et al. (1993) determined from ISM data that the composition of the low-albedo materials covering the Syrtis Major plateau originally consisted of augite-bearing basalt containing both augite and pigeonite, with no appreciable amount of olivine. This description is consistent with a komatiitic basalt. Komatiite is significant for the Earth because it contains a high amount of MgO, implying generation under unique circumstances compared to more typical basaltic compositions and may be similarly important for Mars.

Production and characterization of a functional Iranian white brined cheese by replacement of dairy fat with vegetable oils.

PubMed

Achachlouei, B Fathi; Hesari, J; Damirchi, S Azadmard; Peighambardoust, Sh; Esmaiili, M; Alijani, S

2013-10-01

Full-fat cheese usually contains high amounts of saturated fatty acids and cholesterol, which may have negative health effects. In this study, full-fat white brined cheese, as a control sample, and experimental cheeses with olive and canola oils (T1, white brined cheese containing 50% canola oil, T2, white brined cheese containing 50% olive oil, T3, white brined cheese containing 100% canola oil and T4, white brined cheese containing 100% olive oil) were prepared from bovine milk. Physicochemical properties, lipolysis, proteolysis patterns and sensorial properties in the prepared samples were determined during 80 days of storage at 20-day intervals. Cheese incorporating vegetable oils showed lower amounts of saturated fatty acids and higher amounts of unsaturated fatty acids compared with the full-fat cheese (control) samples. Moisture, pH, lipolysis value, as assessed by the acid-degree value, and proteolysis values (pH 4.6 SN/TN% and NPN/TN%) significantly (p < 0.05) were increased in all samples, whereas total titrable acidity decreased during 40 days of ripening but then increased slightly. Sensory properties of white brined cheese incorporating with vegetable oils were different from those of full-fat cheese samples. White brined cheese containing olive and canola oils (100% fat substitution) received better sensory scores compared to other samples. The results showed that it is possible to replace dairy fat with olive and canola oils, which can lead to produce a new healthy and functional white brined cheese.

EDTA-insoluble, calcium-binding proteoglycan in bovine bone

NASA Technical Reports Server (NTRS)

Hashimoto, Y.; Lester, G. E.; Caterson, B.; Yamauchi, M.

1995-01-01

A calcium ion precipitable, trypsin-generated proteoglycan fragment has been isolated from the demineralized, EDTA-insoluble matrices of bone. The demineralized matrix was completely digested with trypsin, increasing concentrations of CaCl2 were added to the supernatant, and the resulting precipitates were analyzed. The amount of precipitate gradually increased with higher concentrations of calcium and was reversibly solubilized by EDTA. After molecular sieve and anion exchange chromatography, a proteoglycan-containing peak was obtained. Immunochemical analysis showed that this peak contained chondroitin 4-sulfate and possibly keratan sulfate. Amino acid analysis showed that this proteoglycan contained high amounts of aspartic acid/asparagine (Asx), serine (Ser), glutamic acid/glutamine (Glx), proline (Pro), and glycine (Gly); however, it contained little leucine (Leu) which suggests that it is not a member of the leucine-rich small proteoglycan family. In addition, significant amounts of phosphoserine (P-Ser) and hydroxyproline (Hyp) were identified in hydrolysates of this fraction. A single band (M(r) 59 kDa) was obtained on SDS-PAGE that stained with Stains-all but not with Coomassie Brilliant Blue R-250. If bone powder was trypsinized prior to demineralization, this proteoglycan-containing fraction was not liberated. Collectively, these results indicate that a proteoglycan occurs in the demineralized matrix that is precipitated with CaCl2 and is closely associated with both mineral and collagen matrices. Such a molecule might facilitate the structural network for the induction of mineralization in bone.

Comparison of oligosaccharides in milk specimens from humans and twelve other species.

PubMed

Warren, C D; Chaturvedi, P; Newburg, A R; Oftedal, O T; Tilden, C D; Newburg, D S

2001-01-01

Human milk contains large amounts of many oligosaccharides, most of which are fucosylated; several inhibit pathogenic bacteria, viruses, and toxins that cause disease in humans. Although bovine milk is known to have much less and many fewer types of oligosaccharides, no studies heretofore have indicated whether the amount or complexity of human milk oligosaccharides is unique to our species. Toward this end, a comparison was made of the major individual oligosaccharides in milk specimens from a variety of species, including the great apes. The neutral compounds, which represent the bulk of oligosaccharides in human milk, were isolated, perbenzoylated, resolved by high performance liquid chromatography (HPLC), and detected at 229nm. Ambiguous structures were determined by mass spectrometry. All milk specimens contained lactose, although levels were quite low in bear and kangaroo milk. The types of oligosaccharides in milk specimens from the primates resembled those of human milk, but the amounts, especially of the larger molecules, were markedly lower. The relative amounts of oligosaccharides in the bonobo changed over the course of lactation, as they do in humans. Marine mammals generally had few oligosaccharides in their milk other than 2'-fucosyllactose. Grizzly and black bear milk specimens contained a wide range of oligosaccharides, many of which had novel, fucosylated structures. Milk specimens from humans, bears, and marsupials had the greatest quantity of, and the most complex, neutral oligosaccharides. Although human milk contained more oligosaccharide than did milk specimens from the other species studied, the presence of appreciable amounts of complex oligosaccharides was not unique to humans. This finding suggests that in animal milk specimens, as in human milk, neutral fucosylated oligosaccharides potentially offer protection from pathogens to offspring with immature immune systems.

Fabrication and textural characterization of nanoporous carbon electrodes embedded with CuO nanoparticles for supercapacitors.

PubMed

Prasad, Kumaresa P S; Dhawale, Dattatray S; Sivakumar, Thiripuranthagan; Aldeyab, Salem S; Zaidi, Javaid S M; Ariga, Katsuhiko; Vinu, Ajayan

2011-08-01

We introduce a novel strategy of fabricating nanoporous carbons loaded with different amounts of CuO nanoparticles via a hard templating approach, using copper-containing mesoporous silica as the template and sucrose as the carbon source. The nature and dispersion of the CuO nanoparticles on the surface of the nanoporous carbons were investigated by x-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM) and high-resolution transmission electron microscopy (HRTEM). XRD results reveal that nanoporous carbons with embedded CuO nanoparticles exhibit a well-ordered mesoporous structure, whereas the nitrogen adsorption measurements indicate the presence of excellent textural characteristics such as high surface area, large pore volume and uniform pore size distribution. The amount of CuO nanoparticles in the nanochannels of the nanoporous carbon could be controlled by simply varying the Si/Cu molar ratio of the mesoporous silica template. Morphological characterization by SEM and TEM reveals that high-quality CuO nanoparticles are distributed homogeneously within the nanoporous carbon framework. The supercapacitance behavior of the CuO-loaded nanoporous carbons was investigated. The material with a small amount of CuO in the mesochannels and high surface area affords a maximum specific capacitance of 300 F g -1 at a 20 mV s -1 scan rate in an aqueous electrolyte solution. A supercapacitor containing the CuO-loaded nanoporous carbon is highly stable and exhibits a long cycle life with 91% specific capacitance retained after 1000 cycles.

Fabrication and textural characterization of nanoporous carbon electrodes embedded with CuO nanoparticles for supercapacitors

NASA Astrophysics Data System (ADS)

Prasad, Kumaresa P. S.; Dhawale, Dattatray S.; Sivakumar, Thiripuranthagan; Aldeyab, Salem S.; Zaidi, Javaid S. M.; Ariga, Katsuhiko; Vinu, Ajayan

2011-08-01

We introduce a novel strategy of fabricating nanoporous carbons loaded with different amounts of CuO nanoparticles via a hard templating approach, using copper-containing mesoporous silica as the template and sucrose as the carbon source. The nature and dispersion of the CuO nanoparticles on the surface of the nanoporous carbons were investigated by x-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM) and high-resolution transmission electron microscopy (HRTEM). XRD results reveal that nanoporous carbons with embedded CuO nanoparticles exhibit a well-ordered mesoporous structure, whereas the nitrogen adsorption measurements indicate the presence of excellent textural characteristics such as high surface area, large pore volume and uniform pore size distribution. The amount of CuO nanoparticles in the nanochannels of the nanoporous carbon could be controlled by simply varying the Si/Cu molar ratio of the mesoporous silica template. Morphological characterization by SEM and TEM reveals that high-quality CuO nanoparticles are distributed homogeneously within the nanoporous carbon framework. The supercapacitance behavior of the CuO-loaded nanoporous carbons was investigated. The material with a small amount of CuO in the mesochannels and high surface area affords a maximum specific capacitance of 300 F g-1 at a 20 mV s-1 scan rate in an aqueous electrolyte solution. A supercapacitor containing the CuO-loaded nanoporous carbon is highly stable and exhibits a long cycle life with 91% specific capacitance retained after 1000 cycles.

Fabrication and textural characterization of nanoporous carbon electrodes embedded with CuO nanoparticles for supercapacitors

PubMed Central

Prasad, Kumaresa P S; Dhawale, Dattatray S; Sivakumar, Thiripuranthagan; Aldeyab, Salem S; Zaidi, Javaid S M; Ariga, Katsuhiko; Vinu, Ajayan

2011-01-01

We introduce a novel strategy of fabricating nanoporous carbons loaded with different amounts of CuO nanoparticles via a hard templating approach, using copper-containing mesoporous silica as the template and sucrose as the carbon source. The nature and dispersion of the CuO nanoparticles on the surface of the nanoporous carbons were investigated by x-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM) and high-resolution transmission electron microscopy (HRTEM). XRD results reveal that nanoporous carbons with embedded CuO nanoparticles exhibit a well-ordered mesoporous structure, whereas the nitrogen adsorption measurements indicate the presence of excellent textural characteristics such as high surface area, large pore volume and uniform pore size distribution. The amount of CuO nanoparticles in the nanochannels of the nanoporous carbon could be controlled by simply varying the Si/Cu molar ratio of the mesoporous silica template. Morphological characterization by SEM and TEM reveals that high-quality CuO nanoparticles are distributed homogeneously within the nanoporous carbon framework. The supercapacitance behavior of the CuO-loaded nanoporous carbons was investigated. The material with a small amount of CuO in the mesochannels and high surface area affords a maximum specific capacitance of 300 F g-1 at a 20 mV s-1 scan rate in an aqueous electrolyte solution. A supercapacitor containing the CuO-loaded nanoporous carbon is highly stable and exhibits a long cycle life with 91% specific capacitance retained after 1000 cycles. PMID:27877410

Polynuclear aromatic hydrocarbons for fullerene synthesis in flames

DOEpatents

Alford, J. Michael; Diener, Michael D.

2006-12-19

This invention provides improved methods for combustion synthesis of carbon nanomaterials, including fullerenes, employing multiple-ring aromatic hydrocarbon fuels selected for high carbon conversion to extractable fullerenes. The multiple-ring aromatic hydrocarbon fuels include those that contain polynuclear aromatic hydrocarbons. More specifically, multiple-ring aromatic hydrocarbon fuels contain a substantial amount of indene, methylnapthalenes or mixtures thereof. Coal tar and petroleum distillate fractions provide low cost hydrocarbon fuels containing polynuclear aromatic hydrocarbons, including without limitation, indene, methylnapthalenes or mixtures thereof.

Cancer Chemoprevention by Citrus Pulp and Juices Containing High Amounts of β-Cryptoxanthin and Hesperidin

PubMed Central

Tanaka, Takuji; Tanaka, Takahiro; Tanaka, Mayu; Kuno, Toshiya

2012-01-01

β-Cryptoxanthin, a carotenoid, and hesperidin, a flavonoid, possess inhibitory effects on carcinogenesis in several tissues. We recently have prepared a pulp (CHRP) and citrus juices (MJ2 and MJ5) from a satsuma mandarin (Citrus unshiu Mar.) juice (MJ). They contain high amounts of β-cryptoxanthin and hesperidin. We have demonstrated that CHRP and/or MJs inhibit chemically induced rat colon, rat tongue, and mouse lung tumorigenesis. Gavage with CHRP resulted in an increase of activities of detoxifying enzymes in the liver, colon, and tongue rats'. CHRP and MJs were also able to suppress the expression of proinflammatory cytokines and inflammatory enzymes in the target tissues. This paper describes the findings of our in vivo preclinical experiments to develop a strategy for cancer chemoprevention of colon, tongue, and lung neoplasms by use of CHRP and MJs. PMID:22174562

Sol-gel silica-based nanocomposites containing a high PEG amount: Chemical characterization and study of biological properties

NASA Astrophysics Data System (ADS)

Catauro, Michelina; Bollino, Flavia; Gloria, Antonio

2016-05-01

The objective of the present study was to synthesize and to characterize Silica/polyethylene glycol (SiO2/PEG) organic-inorganic hybrid materials containing a high polymer amount (60 and 70 wt%) for biomedical applications. Scanning electron microscopy (SEM) showed that the samples are homogeneous on the nanometer scale, confirming that they are nanocomposites. Fourier transform infrared spectroscopy (FT-IR) proved that the materials are class I hybrids because the two phases (SiO2 and PEG) interact by hydrogen bonds. To evaluate the possibility of using them in the biomedical field, the bioactivity and biocompatibility of the synthesized hybrids have been ascertained. The formation of a hydroxyapatite layer was observed on the hybrid surface by SEM/EDX and FTIR after soaking in simulated body fluid (SBF). Moreover, their biocompatibility was assessed by performing WST-8 cytotoxicity assay in vitro.

Method for preparing corrosion-resistant ceramic shapes

DOEpatents

Arons, R.M.; Dusek, J.T.

1979-12-07

Ceramic shapes having impermeable tungsten coatings can be used for containing highly corrosive molten alloys and salts. The shapes are prepared by coating damp green ceramic shapes containing a small amount of yttria with a tungsten coating slip which has been adjusted to match the shrinkage rate of the green ceramic and which will fire to a theoretical density of at least 80% to provide an impermeable coating.

Method for preparing corrosion-resistant ceramic shapes

DOEpatents

Arons, Richard M.; Dusek, Joseph T.

1983-09-13

Ceramic shapes having impermeable tungsten coatings can be used for containing highly corrosive molten alloys and salts. The shapes are prepared by coating damp green ceramic shapes containing a small amount of yttria with a tungsten coating slip which has been adjusted to match the shrinkage rate of the green ceramic and which will fire to a theoretical density of at least 80% to provide a impermeable coating.

Chromium liquid waste inertization in an inorganic alkali activated matrix: leaching and NMR multinuclear approach.

PubMed

Ponzoni, Chiara; Lancellotti, Isabella; Barbieri, Luisa; Spinella, Alberto; Saladino, Maria Luisa; Martino, Delia Chillura; Caponetti, Eugenio; Armetta, Francesco; Leonelli, Cristina

2015-04-09

A class of inorganic binders, also known as geopolymers, can be obtained by alkali activation of aluminosilicate powders at room temperature. The process is affected by many parameters (curing time, curing temperature, relative humidity etc.) and leads to a resistant matrix usable for inertization of hazardous waste. In this study an industrial liquid waste containing a high amount of chromium (≈ 2.3 wt%) in the form of metalorganic salts is inertized into a metakaolin based geopolymer matrix. One of the innovative aspects is the exploitation of the water contained in the waste for the geopolymerization process. This avoided any drying treatment, a common step in the management of liquid hazardous waste. The evolution of the process--from the precursor dissolution to the final geopolymer matrix hardening--of different geopolymers containing a waste amount ranging from 3 to 20%wt and their capability to inertize chromium cations were studied by: i) the leaching tests, according to the EN 12,457 regulation, at different curing times (15, 28, 90 and 540 days) monitoring releases of chromium ions (Cr(III) and Cr(VI)) and the cations constituting the aluminosilicate matrix (Na, Si, Al); ii) the humidity variation for different curing times (15 and 540 days); iii) SEM characterization at different curing times (28 and 540 days); iv) the trend of the solution conductivity and pH during the leaching test; v) the characterization of the short-range ordering in terms of TOT bonds (where T is Al or Si) by (29)Si and (27)Al solid state magic-angle spinning nuclear magnetic resonance (ss MAS NMR) for geopolymers containing high amounts of waste (10-20%wt). The results show the formation of a stable matrix after only 15 days independently on the waste amount introduced; the longer curing times increase the matrices stabilities and their ability to immobilize chromium cations. The maximum amount of waste that can be inertized is around 10 wt% after a curing time of 28 days. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of flax addition on the flavor profile and acceptability of bagels.

PubMed

Aliani, Michel; Ryland, Donna; Pierce, Grant N

2012-01-01

Bakery products containing flaxseed, a rich source of alpha linolenic acid (ALA), may provide health benefits. However, the effect of adding flaxseed, especially in the high amounts required for use as the food supplement in clinical trials (23% by weight of the raw ingredients), may affect the flavor characteristics and consumer acceptability. Sensory attributes of bagels containing 30 g of milled flaxseed were evaluated by a 9 member trained panel using a descriptive test and by 89 participants using a consumer test. Grain/flax aroma and flavor were significantly higher for the flax bagels compared to the nonflax bagels. The cinnamon raisin bagel had significantly lower grain/flax aroma and flavor and significantly higher sweet aroma and taste compared to the plain and sunflower sesame types. Older consumers rated the appearance, color, and flavor of the bagels significantly higher than the younger consumers possibly leading to higher compliance in clinical studies for this age group. Bagels with flax showed a significantly lower mean value for flavor acceptability, overall acceptability, and frequency of eating compared to bagels without flax. Appearance, color, and texture acceptability showed no significant differences. The cinnamon raisin bagel had significantly higher flavor acceptance compared to sunflower sesame and plain bagels. In conclusion, for bagels containing 6 g ALA in the form of milled flaxseed, cinnamon raisin appears to be a promising flavoring alternative for ALA fortification for use in clinical trials or as part of the daily diet. Consumers are seeking functional foods that contain omega-3 fatty acids. Bagels made with 23% milled flaxseed (approximately 2 times the amount in regular flax baked products) provided 6 g ALA, an amount high enough to test the efficacy of ALA in human subjects without causing gastrointestinal distress. This study showed that flaxseed aroma and flavor were detected in fortified compared to nonfortified bagels but bagels with this high flaxseed amount were still acceptable with the addition of cinnamon raisin flavoring. Commercial bakeries can use these results to formulate healthy, tasty, and convenient products. © 2011 Institute of Food Technologists®

Studies of cellulose surfaces by titration and ESCA

NASA Astrophysics Data System (ADS)

Stenius, Per; Laine, Janne

1994-01-01

The surface properties of unbleached kraft pulp fibers of varying lignin content prepared by digestion with different amounts of excess alkali have been investigated using polyelectrolyte titration, potentiometric titration and ESCA. The surfaces contain two different acidic groups that dissociate completely above pH 7.5, one with pK ≈ 3.6 and one with pK ≈ 5.7. The amount of the latter group correlates directly with the amount of lignin in the pulp. The ESCA analysis indicates that the relative amount of carboxylic groups and alkyl carbon in the surface decreases as the lignin content decreases and also that material with high alkyl carbon content is enriched in the outermost surface of the cellulose. Thus, a combination of ESCA analysis and high-precision titrations is able to yield a very detailed picture of the effect of digestion conditions on surface properties of cellulose fibers of direct relevance to paper properties.

An efficient and rapid transgenic pollen screening and detection method using flow cytometry.

PubMed

Moon, Hong S; Eda, Shigetoshi; Saxton, Arnold M; Ow, David W; Stewart, C Neal

2011-01-01

Assaying for transgenic pollen, a major vector of transgene flow, provides valuable information and essential data for the study of gene flow and assessing the effectiveness of transgene containment. Most studies have employed microscopic screening methods or progeny analyses to estimate the frequency of transgenic pollen. However, these methods are time-consuming and laborious when large numbers of pollen grains must be analyzed to look for rare transgenic pollen grains. Thus, there is an urgent need for the development of a simple, rapid, and high throughput analysis method for transgenic pollen analysis. In this study, our objective was to determine the accuracy of using flow cytometry technology for transgenic pollen quantification in practical application where transgenic pollen is not frequent. A suspension of non-transgenic tobacco pollen was spiked with a known amount of verified transgenic tobacco pollen synthesizing low or high amounts of green fluorescent protein (GFP). The flow cytometric method detected approximately 75% and 100% of pollen grains synthesizing low and high amounts of GFP, respectively. The method is rapid, as it is able to count 5000 pollen grains per minute-long run. Our data indicate that this flow cytometric method is useful to study gene flow and assessment of transgene containment.

A Model for Investigating Predictive Validity at Highly Selective Institutions.

ERIC Educational Resources Information Center

Gross, Alan L.; And Others

A statistical model for investigating predictive validity at highly selective institutions is described. When the selection ratio is small, one must typically deal with a data set containing relatively large amounts of missing data on both criterion and predictor variables. Standard statistical approaches are based on the strong assumption that…

Electrodeless discharge lamp is easily started, has high stability

NASA Technical Reports Server (NTRS)

Bell, W. E.; Bloom, A. L.

1966-01-01

Electrodeless discharge borosilicate glass lamp is used in various high-resolution optical systems. It is partially charged with krypton, contains small amounts of rubidium, and is enclosed in a hermetically sealed envelope that maintains the lamp at an optimum temperature during discharge. The lamp is quickly started by its excitation coil.

Matrix Transformation in Boron Containing High-Temperature Co-Re-Cr Alloys

NASA Astrophysics Data System (ADS)

Strunz, Pavel; Mukherji, Debashis; Beran, Přemysl; Gilles, Ralph; Karge, Lukas; Hofmann, Michael; Hoelzel, Markus; Rösler, Joachim; Farkas, Gergely

2018-03-01

An addition of boron largely increases the ductility in polycrystalline high-temperature Co-Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ɛ (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr2Re3 type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co-17Re-23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ɛ to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co-17Re-23Cr-1.2Ta-2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0-1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.

Viscoplasticity of simulated high-level radioactive waste glass containing platinum group metal particles

NASA Astrophysics Data System (ADS)

Uruga, Kazuyoshi; Usami, Tsuyoshi; Tsukada, Takeshi; Komamine, Satoshi; Ochi, Eiji

2014-09-01

The shear rate dependency of the viscosity of three simulated high-level radioactive waste glasses containing 0, 1.2 and 4.5 wt% platinum group metals (PGMs) was examined at a temperature range of 1173-1473 K by a rotating viscometer. Shear stress when the shear rate equals zero, i.e. yield stress, was also measured by capillary method. The viscosity of the glass containing no PGM was shear rate-independent Newtonian fluid. On the other hand, the apparent viscosity of the glasses containing PGMs increased with decreasing shear rate, and nonzero amount of yield stresses were detected from both glasses. The viscosity and yield stress of the glass containing 4.5 wt% PGMs was roughly one to two orders of magnitude greater than the glass containing 1.2 wt% PGMs. These viscoplastic properties were numerically expressed by Casson equation.

Ceramic heat exchanger

DOEpatents

LaHaye, Paul G.; Rahman, Faress H.; Lebeau, Thomas P. E.; Severin, Barbara K.

1998-01-01

A tube containment system. The tube containment system does not significantly reduce heat transfer through the tube wall. The contained tube is internally pressurized, and is formed from a ceramic material having high strength, high thermal conductivity, and good thermal shock resistance. The tube containment system includes at least one ceramic fiber braid material disposed about the internally pressurized tube. The material is disposed about the tube in a predetermined axial spacing arrangement. The ceramic fiber braid is present in an amount sufficient to contain the tube if the tube becomes fractured. The tube containment system can also include a plurality of ceramic ring-shaped structures, in contact with the outer surface of the tube, and positioned between the tube and the ceramic fiber braid material, and/or at least one transducer positioned within tube for reducing the internal volume and, therefore, the energy of any shrapnel resulting from a tube fracture.

Ceramic heat exchanger

DOEpatents

LaHaye, P.G.; Rahman, F.H.; Lebeau, T.P.; Severin, B.K.

1998-06-16

A tube containment system is disclosed. The tube containment system does not significantly reduce heat transfer through the tube wall. The contained tube is internally pressurized, and is formed from a ceramic material having high strength, high thermal conductivity, and good thermal shock resistance. The tube containment system includes at least one ceramic fiber braid material disposed about the internally pressurized tube. The material is disposed about the tube in a predetermined axial spacing arrangement. The ceramic fiber braid is present in an amount sufficient to contain the tube if the tube becomes fractured. The tube containment system can also include a plurality of ceramic ring-shaped structures, in contact with the outer surface of the tube, and positioned between the tube and the ceramic fiber braid material, and/or at least one transducer positioned within tube for reducing the internal volume and, therefore, the energy of any shrapnel resulting from a tube fracture. 6 figs.

Comparison and optimization of detection methods for noroviruses in frozen strawberries containing different amounts of RT-PCR inhibitors.

PubMed

Bartsch, Christina; Szabo, Kathrin; Dinh-Thanh, Mai; Schrader, Christina; Trojnar, Eva; Johne, Reimar

2016-12-01

Frozen berries have been repeatedly identified as vehicles for norovirus (NoV) transmission causing large gastroenteritis outbreaks. However, virus detection in berries is often hampered by the presence of RT-PCR-inhibiting substances. Here, several virus extraction methods for subsequent real-time RT-PCR-based NoV-RNA detection in strawberries were compared and optimized. NoV recovery rates (RRs) between 0.21 ± 0.13% and 10.29 ± 6.03% were found when five different artificially contaminated strawberry batches were analyzed by the ISO/TS15216-2 method indicating the presence of different amounts of RT-PCR inhibitors. A comparison of five different virus extraction methods using artificially contaminated strawberries containing high amounts of RT-PCR inhibitors revealed the best NoV RRs for the ISO/TS15216 method. Further improvement of NoV RRs from 2.83 ± 2.92% to 15.28 ± 9.73% was achieved by the additional use of Sephacryl(®)-based columns for RNA purification. Testing of 22 frozen strawberry samples from a batch involved in a gastroenteritis outbreak resulted in 5 vs. 13 NoV GI-positive and in 9 vs. 20 NoV GII-positive samples using the original ISO/TS15216 method vs. the extended protocol, respectively. It can be concluded that the inclusion of an additional RNA purification step can increase NoV detection by the ISO/TS15216-2 method in frozen berries containing high amounts of RT-PCR inhibitors. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Destruction of Navy Hazardous Wastes by Supercritical Water Oxidation

DTIC Science & Technology

1994-08-01

cleaning and derusting (nitrite and citric acid solutions), electroplating ( acids and metal bearing solutions), electronics and refrigeration... acid forming chemical species or that contain a large amount of dissolved solids present a challenge to current SCWO •-chnology. Approved for public...Waste streams that contain a large amount of mineral- acid forming chemical species or that contain a large amount of dissolved solids present a challenge

Hollow microspheres of silica glass and method of manufacture

DOEpatents

Downs, Raymond L.; Miller, Wayne J.

1982-01-01

A method of manufacturing gel powder suitable for use as a starting material in the manufacture of hollow glass microspheres having a high concentration of silica. The powder is manufactured from a gel containing boron in the amount of about 1% to 20% (oxide equivalent mole percent), alkali metals, specifically potassium and sodium, in an amount exceeding 8% total, and the remainder silicon. Preferably, the ratio of potassium to sodium is greater than 1.5.

Capsicum chinensis L. growth and nutraceutical properties are enhanced by biostimulants in a long-term period: chemical and metabolomic approaches

PubMed Central

Ertani, Andrea; Pizzeghello, Diego; Francioso, Ornella; Sambo, Paolo; Sanchez-Cortes, Santiago; Nardi, Serenella

2014-01-01

Two biostimulants, one derived from alfalfa plants (AH) and the other obtained from red grape (RG), were chemically characterized using enzyme linked immuno-sorbent assays, Fourier transform infrared (FT-IR) and Raman spectroscopies. Two doses (50 and 100 mL L−1 for RG, and 25 and 50 mL L−1 for AH) of biostimulants were applied to Capsicum chinensis L. plants cultivated in pots inside a tunnel. The experimental design consisted of the factorial combination of treatment (no biostimulant, plus AH, plus RG) at three doses (zero, low, and high) and two time-course applications (at the second and fourth week after transplantation) and the effects were recorded at flowering and maturity. Both biostimulants contained different amounts of indoleacetic acid and isopentenyladenosine; the AH spectra exhibited amino acid functional groups in the peptidic structure, while the RG spectra showed the presence of polyphenols, such as resveratrol. These results revealed that at flowering, RG and AH increased the weights of fresh leaves and fruits and the number of green fruits, whereas at maturity, the biostimulants most affected the fresh weight and number of red fruits. At flowering, the leaves of the treated plants contained high amounts of epicatechin, ascorbic acid, quercetin, and dihydrocapsaicin. At maturity, the leaves of the treated plants exhibited elevated amounts of fructose, glucose, chlorogenic, and ferulic acids. Moreover, green fruits exhibited a high content of chlorogenic acid, p-hydroxybenzoic acid, p-coumaric acid and antioxidant activity, while both AH- and RG-treated red fruits were highly endowed in capsaicin. The 1H high-resolution magic-angle spinning (HRMAS)-nuclear magnetic resonance (NMR) spectra of red fruits revealed that both products induced a high amount of NADP+, whereas RG also increased glucose, fumarate, ascorbate, thymidine and high molecular weight species. Our results suggested that AH and RG promoted plant growth and the production of secondary metabolites, such as phenols. PMID:25136346

Emission FTIR analyses of thin microscopic patches of jet fuel residue deposited on heated metal surface

NASA Technical Reports Server (NTRS)

Lauer, J. L.; Vogel, P.

1984-01-01

Deposits laid down in patches on metal strips in a high pressure/high temperature fuel system simulator operated with aerated fuel at varying flow rates were analyzed by emission FTIR in terms of functional groups. Significant differences were found in the spectra and amounts of deposits derived from fuels to which small concentrations of oxygen-, nitrogen-, or sulfur-containing heterocyclics or metal naphthenates were added. The spectra of deposits generated on strips by heating fuels and air in a closed container were very different from those of the flowing fluid deposits. One such closed-container dodecane deposit on silver gave a strong surface-enhanced Raman spectrum.

Occurrence of sarmentosin and other hydroxynitrile glucosides in Parnassius (papilionidae) butterflies and their food plants.

PubMed

Bjarnholt, Nanna; Nakonieczny, Mirosław; Kędziorski, Andrzej; Debinski, Diane M; Matter, Stephen F; Olsen, Carl Erik; Zagrobelny, Mika

2012-05-01

Sequestration of plant secondary metabolites is a widespread phenomenon among aposematic insects. Sarmentosin is an unsaturated γ-hydroxynitrile glucoside known from plants and some Lepidoptera. It is structurally and biosynthetically closely related to cyanogenic glucosides, which are commonly sequestered from food plants and/or de novo synthesized by lepidopteran species. Sarmentosin was found previously in Parnassius (Papilionidae) butterflies, but it was not known how the occurrence was related to food plants or whether Parnassius species could biosynthesize the compound. Here, we report on the occurrence of sarmentosin and related compounds in four different Parnassius species belonging to two different clades, as well as their known and suspected food plants. There were dramatic differences between the two clades, with P. apollo and P. smintheus from the Apollo group containing high amounts of sarmentosin, and P. clodius and P. mnemosyne from the Mnemosyne group containing low or no detectable amounts. This was reflected in the larval food plants; P. apollo and P. smintheus larvae feed on Sedum species (Crassulaceae), which all contained considerable amounts of sarmentosin, while the known food plants of the two other species, Dicentra and Corydalis (Fumariaceae), had no detectable levels of sarmentosin. All insects and plants containing sarmentosin also contained other biosynthetically related hydroxynitrile glucosides in patterns previously reported for plants, but not for insects. Not all findings could be explained by sequestration alone and we therefore hypothesize that Parnassius species are able to de novo synthesize sarmentosin.

Dehulling of Cuphea PSR23 Seeds to Reduce Color of the Extracted Oil

USDA-ARS?s Scientific Manuscript database

Oil extracted from the seeds Cuphea PSR23, a semi-domesticated, high-capric acid hybrid from C. viscosissima x C. lanceolata, by screw-pressing contained 200-360 ppm of chlorophyll. A high amount of bleaching clay was needed during refining to remove the chlorophyll in the oil. In this paper, dehu...

Structural features and complement-fixing activity of pectin from three Brassica oleracea varieties: white cabbage, kale, and red kale.

PubMed

Samuelsen, Anne Berit; Westereng, Bjørge; Yousif, Osman; Holtekjølen, Ann Katrin; Michaelsen, Terje E; Knutsen, Svein H

2007-02-01

Leaves of different cabbage species are used both as food and as wound healing remedies in traditional medicine. This supposed wound healing activity might be connected to presence of immunomodulating water soluble polysaccharides. To study this, three different cabbage varieties, white cabbage (W), kale (K), and red kale (RK), were pretreated with 80% ethanol and then extracted with water at 50 degrees C and 100 degrees C for isolation of polysaccharide-containing fractions. The fractions were analyzed for monosaccharide composition, glycosidic linkages, Mw distribution, protein content, and phenolic compounds and then tested for complement-fixing activity. All fractions contained pectin type polysaccharides with linkages corresponding to homogalacturonan and hairy regions. Those extracted at 50 degrees C contained higher amounts of neutral side chains and were more active in the complement-fixation test than those extracted at 100 degrees C. The fractions can be ranged by decreasing activity: K-50 > RK-50 > W-50 approximately = K-100 > RK100 approximately = W-100. Studies on structure-activity relationships (SAR) employing multivariate statistical analysis strongly suggest that the magnitude of the measured activity is influenced by the content of certain side chains in the polymers. High activity correlates to large neutral side chains with high amounts of (1-->6)- and (1-->3,6)-linked Gal and low amounts of (1-->4)-linked GalA but not on molecular weight distribution of the polymers.

Revaluation of stockpile amount of PFOS-containing aqueous film-forming foam in Japan: gaps and pitfalls in the stockpile survey.

PubMed

Zushi, Yasuyuki; Yamamoto, Atsushi; Tsunemi, Kiyotaka; Masunaga, Shigeki

2017-03-01

Stockpiles of perfluoro-octane sulfonic acid (PFOS) containing aqueous film-forming foam (AFFF) have the potential to be emitted by leaching, spills, and during use in fire response and other processes. Several studies have discussed the high levels of stockpiled PFOS-containing AFFF and the risk they pose to the environment; however, there are large gaps in the amounts in Japan compared with other countries. For example, 300 tons are stockpiled in Canada, 2200-2600 tons in Switzerland, 1400 tons in Norway, and 19,000 tons in Japan from their reports for publication. The gap is considered to be a result of lack of surveys of several important sources. In this study, we revaluated the stockpile of AFFF in Japan to verify the reported value and identify the source of this gap based on information available in peer-reviewed papers, governmental reports, and business reports. The major reason for the gap between Japan and other countries was considered to be the survey of stockpiles in car-parking facilities, which accounted for 46.7% of the total amounts in Japan, but were not considered in other countries. These stockpiles indicate a high potential for accidental leaching or spilling of the AFFF by careless storage. Therefore, it is recommended that continual surveys of the AFFF stockpile in car-parking facilities be conducted in the rest of the world.

Application of high-performance liquid chromatography for research of salicin in bark of different varieties of Salix.

PubMed

Kenstaviciene, Palmyra; Nenortiene, Palma; Kiliuviene, Guoda; Zevzikovas, Andrejus; Lukosius, Audronis; Kazlauskiene, Daiva

2009-01-01

Willow (Salix L.) species are widely spread in Lithuanian natural dendroflora. Willow bark contains active substances known for anti-inflammatory properties and is known as a phytotherapeutic precursor of aspirin. Bark extracts are components of analgesic and antirheumatic preparations. Therapeutic effectiveness is associated with salicin (2-(hydroxymethyl)phenyl-beta-D-glucopyranoside), which turns into salicylic acid. Increasing attention to natural preparations gives primary importance to research of plants. This study focused on 12 willow taxa and employed routine pharmacopoeia methods. High-performance liquid chromatography method was applied for the analysis of bark extractions. The investigation revealed that not all willow species accumulated a therapeutically sufficient amount of salicin. Bark samples were investigated after 1- and 2-year growth in autumn and spring. Salicin content ranged from 0.08 to 12.6%. Higher contents of active materials were determined in autumn and in 2-year-old willows. Certain willow taxa (Salix alba L., Salix mollissima L., Salix triandra L., Salix viminalis "Americana", Salix dasyclados L.) possessed extremely low salicin amounts. In the second year, analysis covered 32 willow species. Results indicated striking differences in salicin amounts (from 0.04% in Salix viminalis "Americana" to 12.06% in Salix acutifolia). Willow species, plant age, and season should be considered when collecting medicinal plant material. The amount of salicylates in 2-year-old willow bark collected in autumn exceeded by 25% that in 1-year-old willow bark collected in spring. Bark of some analyzed willow species contained the amount of salicylates too low for using as anti-inflammatory or antipyretic remedy.

Sorbitol, Rubus fruit, and misconception

USDA-ARS?s Scientific Manuscript database

It is unclear how the misunderstanding that Rubus fruits (e.g., blackberries, raspberries) are high in sugar alcohol began, or when it started circulating in the United States. In reality, they contain little sugar alcohol. Numerous research groups have reported zero detectable amounts of sugar alco...

Lightweight concrete with enhanced neutron shielding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brindza, Paul Daniel; Metzger, Bert Clayton

A lightweight concrete containing polyethylene terephthalate in an amount of 20% by total volume. The concrete is enriched with hydrogen and is therefore highly effective at thermalizing neutrons. The concrete can be used independently or as a component of an advanced neutron radiation shielding system.

The efficacy of sugar labeling formats: Implications for labeling policy.

PubMed

Vanderlee, Lana; White, Christine M; Bordes, Isabelle; Hobin, Erin P; Hammond, David

2015-12-01

To examine knowledge of sugar recommendations and test the efficacy of formats for labeling total and added sugar on pre-packaged foods. Online surveys were conducted among 2008 Canadians aged 16-24. Participants were asked to identify recommended limits for total and added sugar consumption. In Experiment 1, participants were randomized to one of six labeling conditions with varying information for total sugar for a high- or low-sugar product and were asked to identify the relative amount of total sugar in the product. In Experiment 2, participants were randomized to one of three labels with different added sugar formats and were asked if the product contained added sugar and the relative amount of added sugar. Few young people correctly identified recommendations for total sugar (5%) or added sugar (7%). In Experiment 1, those who were shown percent daily value information were more likely to correctly identify the relative amount of total sugar (P < 0.05). In Experiment 2, those shown added sugar information were more likely to correctly identify that the product contained added sugar and the relative amount of added sugar in the product (P < 0.05). Improved labeling may improve consumer understanding of the amount of sugars in food products. © 2015 The Obesity Society.

Ammonia Detection

NASA Technical Reports Server (NTRS)

Ward, William Douglas (Inventor)

2014-01-01

The different advantageous embodiments provide for identifying gas leakage in a platform. A processor unit identifies a rate of the gas of the substance leaking from a container in a first compartment for a platform. The processor unit also identifies an amount of gas that has leaked from the container at a selected time based on the rate of the gas of the substance leaking from the container and a total time. The processor unit identifies an amount of the gas of the substance present in a number of compartments associated with the first compartment using the amount of gas leaked from the container in the first compartment and a pressure for each compartment in the number of compartments. The processor unit determines whether the amount of gas in at least one of the first compartment and the number of compartments is outside of a desired amount for the gas.

Deep learning as a tool to distinguish between high orbital angular momentum optical modes

NASA Astrophysics Data System (ADS)

Knutson, E. M.; Lohani, Sanjaya; Danaci, Onur; Huver, Sean D.; Glasser, Ryan T.

2016-09-01

The generation of light containing large degrees of orbital angular momentum (OAM) has recently been demon- strated in both the classical and quantum regimes. Since there is no fundamental limit to how many quanta of OAM a single photon can carry, optical states with an arbitrarily high difference in this quantum number may, in principle, be entangled. This opens the door to investigations into high-dimensional entanglement shared between states in superpositions of nonzero OAM. Additionally, making use of non-zero OAM states can allow for a dramatic increase in the amount of information carried by a single photon, thus increasing the information capacity of a communication channel. In practice, however, it is difficult to differentiate between states with high OAM numbers with high precision. Here we investigate the ability of deep neural networks to differentiate between states that contain large values of OAM. We show that such networks may be used to differentiate be- tween nearby OAM states that contain realistic amounts of noise, with OAM values of up to 100. Additionally, we examine how the classification accuracy scales with the signal-to-noise ratio of images that are used to train the network, as well as those being tested. Finally, we demonstrate the simultaneous classification of < 100 OAM states with greater than 70 % accuracy. We intend to verify our system with experimentally-produced classi- cal OAM states, as well as investigate possibilities that would allow this technique to work in the few-photon quantum regime.

An Examination of Binder Systems and Their Influences on Burn Rates of High-Nitrogen Containing Formulations

DTIC Science & Technology

2011-01-01

sought-after to advance existing HHS technology. Currently existing HHS candle formulations contain significant amounts of potassium perchlorate...Defense spends tens of billions of dollars annually on per- chlorate remediation efforts. Therefore, efforts to elimi- nate perchlorate from military...develop per- chlorate -free formulations of the M126A1 red star para- chute. To maximize the performance of these formula- tions, KClO4 was replaced

Chemical Reactions and Properties of Organosilicon Compounds Related to New Materials.

DTIC Science & Technology

1985-10-31

out. The compound behaves like an olefin in some reactions, for in- stance addition of hydrogen halides or chlorine: C1 2 HCI Mes 2 SiCl-SiClMes2...polymers have been synthesized which contain some silicon atoms bonded to hydrogen . These become crosslinked when mixed with substances containing several...and highly efficient catalysts, very small amounts are required in this process. Moreover, photocatalysis using polysilanes produces polymers with

Selenium content of game meat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medeiros, L.C.; Belden, R.P.

Selenium (Se) content of elk, deer, bison and beef were measured and compared. Samples were obtained from animals grazed on soil known to contain high, but variable amounts of Se. Beef were feedlot grazed and elk, deer, and bison were from captive or semi-captive herds. Selenium content was determined by graphite furnace after high pressure wet microwave digestion of samples. Deer and bison contained more Se than elk or beef. On a dry weight basis, deer contained more Se than bison. Game species contained more Se than beef. Within samples from male elk and deer and elk and bison ofmore » both genders, there were interactions between specie and muscle effects. Muscle and gender did not significantly influence Se content. The animals from which these samples were taken were supplemented with feeds grown on high Se containing soils, which was reflected in all values. Se values were twofold higher than those previously reported for meat. Those consuming large quantities of game from areas with high Se soil may need to monitor Se intake to avoid consuming excessive quantities.« less

The use of electrochemistry for the synthesis of 17 alpha-hydroxyprogesterone by a fusion protein containing P450c17.

PubMed

Estabrook, R W; Shet, M S; Faulkner, K; Fisher, C W

1996-11-01

A method has been developed for the commercial application of the unique oxygen chemistry catalyzed by various cytochrome P450s. This is illustrated here for the synthesis of hydroxylated steroids. This method requires the preparation of large amounts of enzymatically functional P450 proteins that can serve as catalysts and a technique for providing electrons at an economically acceptable cost. To generate large amounts of enzymatically active recombinant P450s we have engineered the cDNAs for various P450s, including bovine adrenal P450c17, by linking them to a modified cDNA for rat NADPH-P450 reductase and placing them in the plasmid pCWori+. Transformation of E. coli results in the high level expression of an enzymatically active protein that can be easily purified by affinity chromatography. Incubation of the purified enzyme with steroid in a reaction vessel containing a platinum electrode and a Ag/AgCl electrode couple poised at -650 mV, together with the electromotively active redox mediator, cobalt sepulchrate, results in the 17 alpha-hydroxylation of progesterone at rates as high as 25 nmoles of progesterone hydroxylated/min/nmole of P450. Thus, high concentrations of hydroxylated steroids can be produced with incubation conditions of hours duration without the use of costly NADPH. Similar experiments have been carried out for the generation of the 6 beta-hydroxylation product of testosterone (using a fusion protein containing human P450 3A4). It is apparent that this method is applicable to many other P450 catalyzed reactions for the synthesis of large amounts of hydroxylated steroid metabolites. The electrochemical system is also applicable to drug discovery studies for the characterization of drug metabolites.

Identification, occurrence and activity of quinazoline alkaloids in Peganum harmala.

PubMed

Herraiz, Tomás; Guillén, Hugo; Arán, Vicente J; Salgado, Antonio

2017-05-01

Peganum harmala L. is a medicinal plant from the Mediterranean region and Asia currently used for recreative psychoactive purposes (Ayahuasca analogue), and increasingly involved in toxic cases. Its psychopharmacological and toxicological properties are attributed to quinazoline and β-carboline alkaloids. In this work three major quinazoline alkaloids were isolated from P. harmala extracts and characterized as peganine (vasicine), deoxypeganine (deoxyvasicine) and a novel compound identified by HPLC-DAD-MS and NMR as peganine β-d-glucopyranosyl-(1 → 6)-β-d-glucopyranoside (peganine glycoside). Peganine appeared in flowers and leaves in high levels; high amounts of deoxypeganine and peganine were found in immature and green fruits whereas peganine and peganine glycoside accumulated in high amount in dry seeds reaching up to 1 and 3.9% (w/w), respectively. Roots and stems contained low amount of quinazolines. Seeds extracts containing both quinazoline and β-carboline alkaloids potently inhibited human monoamine oxidase (MAO)-A. However, quinazoline alkaloids did not contribute to MAO inhibition that was due to β-carbolines, suggesting that MAO-related psychoactive or toxic actions do not arise from quinazolines. Quinazoline alkaloids were poor radical scavengers in the ABTS assay whereas seed extracts had good activity. Quinazoline alkaloids are known to exert bronchodilator and abortifacient actions, and could contribute to such effects reported in P. harmala. Copyright © 2017 Elsevier Ltd. All rights reserved.

Multi-block analysis coupled with GC-FID and ATR-MIR for the evaluation of thermal degradation in vegetable oils.

PubMed

Rampazzo, Valéria; Ribeiro, Leomara Floriano; Santos, Poliana Macedo; Ferreira, Maresa Custódio Molinari; Bona, Evandro; Maciel, Giselle Maria; Haminiuk, Charles Windson Isidoro

2018-04-01

The effect of heating in twenty-four different oil samples was evaluated via iodine value (IV), gas chromatography (GC) and mid-infrared (MIR) analyses. Common components and specific weights analysis (CCSWA) was applied to distribute the samples according to their most relevant characteristics, thereby revealing the influence of heating on composition. Instrumental analysis indicated a high amount of beneficial fatty acids, such as alpha-linolenic acid, in less exploited oils such as chia oil. This oil can present nutritional damage when subjected to high temperatures and is thus less recommended for frying. Conversely, oils containing high amounts of linoleic acid, such as almond and nut oils, as well as those containing equivalent amounts of alpha-linolenic and linoleic acids, such as golden flaxseed and flaxseed oils, displayed greater resistance to temperature. The 3008/cm band exhibited greater intensity in oils with a higher degree of unsaturation, such as chia and linseed oils, a phenomenon mainly influenced by the presence of linoleic and alpha-linolenic fatty acids. After heating, there was a decrease in the intensity of this band. The main parameter discriminating the tested oil samples based on CCSWA was the degree of unsaturation. Overall, the employed statistical method was effective in analyzing the data obtained via the applied techniques, revealing the influence of each assessed parameter. Copyright © 2018 Elsevier B.V. All rights reserved.

Headspace concentrations of explosive vapors in containers designed for canine testing and training: theory, experiment, and canine trials.

PubMed

Lotspeich, Erica; Kitts, Kelley; Goodpaster, John

2012-07-10

It is a common misconception that the amount of explosive is the chief contributor to the quantity of vapor that is available to trained canines. In fact, this quantity (known as odor availability) depends not only on the amount of explosive material, but also the container volume, explosive vapor pressure and temperature. In order to better understand odor availability, headspace experiments were conducted and the results were compared to theory. The vapor-phase concentrations of three liquid explosives (nitromethane, nitroethane and nitropropane) were predicted using the Ideal Gas Law for containers of various volumes that are in use for canine testing. These predictions were verified through experiments that varied the amount of sample, the container size, and the temperature. These results demonstrated that the amount of sample that is needed to saturate different sized containers is small, predictable and agrees well with theory. In general, and as expected, once the headspace of a container is saturated, any subsequent increase in sample volume will not result in the release of more vapors. The ability of canines to recognize and alert to differing amounts of nitromethane has also been studied. In particular, it was found that the response of trained canines is independent of the amount of nitromethane present, provided it is a sufficient quantity to saturate the container in which it is held. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Boron/Carbon/Silicon/Nitrogen Ceramics And Precursors

NASA Technical Reports Server (NTRS)

Riccitiello, Salvatore; Hsu, Ming TA; Chen, Timothy S.

1996-01-01

Ceramics containing various amounts of boron, carbon, silicon, and nitrogen made from variety of polymeric precursors. Synthesized in high yield from readily available and relatively inexpensive starting materials. Stable at room temperature; when polymerized, converted to ceramics in high yield. Ceramics resist oxidation and other forms of degradation at high temperatures; used in bulk to form objects or to infiltrate other ceramics to obtain composites having greater resistance to oxidation and high temperatures.

The effect of carbon distribution on deformation and cracking of Ni-16Cr-9Fe-C alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hertzberg, J.L.; Was, G.S.

1995-12-31

Constant extension rate tensile (CERT) tests and constant load tensile (CLT) tests were conducted on controlled purity Ni-16Cr-9Fe-C alloys. The amount and form of carbon were varied in order to investigate the roles of carbon in solution and as intergranular (IG) carbides in the deformation and IG cracking behavior in 360 C argon and primary water environments. Results show that the strength, ductility and creep resistance of these alloys are increased with carbon present in solid solution, while IG cracking on the fracture surface is suppressed. Alloys containing carbon in the form of IG carbides, however, exhibit reduced strength andmore » ductility relative to carbon in solution, while maintaining high IG cracking resistance with respect to carbon-free alloys. CERT results of commercial alloy 600 and controlled purity, carbon containing alloys yield comparable failure strains and IG cracking amounts. CLT comparisons with creep tests of alloy 600 suggest that alloys containing IG carbides are more susceptible to creep than those containing all carbon in solid solution.« less

W-containing oxide layers obtained on aluminum and titanium by PEO as catalysts in thiophene oxidation

NASA Astrophysics Data System (ADS)

Rudnev, V. S.; Lukiyanchuk, I. V.; Vasilyeva, M. S.; Morozova, V. P.; Zelikman, V. M.; Tarkhanova, I. G.

2017-11-01

W-containing oxide layers fabricated on titanium and aluminum alloys by Plasma electrolytic oxidation (PEO) have been tested in the reaction of the peroxide oxidation of thiophene. Samples with two types of coatings have been investigated. Coatings I contained tungsten oxide in the matrix and on the surface of amorphous silica-titania or silica-alumina layers, while coatings II comprised crystalline WO3 and/or Al2(WO4)3. Aluminum-supported catalyst containing a smallest amount of transition metals in the form of tungsten oxides and manganese oxides in low oxidation levels showed high activity and stability.

Keepers of the Hematite

NASA Technical Reports Server (NTRS)

2004-01-01

This figure shows spectra taken by the Mars Exploration Rover Opportunity's Moessbauer spectrometer at various spots in 'Eagle Crater.' From top to bottom, the spectra represent soil measurements taken from the center of the crater and out to the rim. The top spectrum taken on sol 56 near the center of the crater shows a basaltic mineral composition and only minor amounts of hematite. Basalts are volcanic minerals and hematite is an iron-bearing mineral often formed in water. Moving closer to the rim, the spectra show increasing amounts of hematite with the 'Punaluu' site containing the highest amounts seen to date on Mars. Only minor basaltic components are seen in this sample.

The corresponding microscopic image of Punaluu shows a high density of 'blueberries,' indicating that these sphere-like grains are responsible for the observed high levels of hematite.

Performance improvement of PEFC modules with cell containing low amount of platinum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyake, Y.; Kadowaki, M.; Hamada, A.

1996-12-31

Cell components of the PEFC module were studied to improve the module performance. The cell performance in a high air utilization region was improved by selecting an air channel design of the separator in which high air flow speed was obtained. Optimization of Teflon{reg_sign} amount on the cathode backing carbon paper also contributed the cell performance. Modifications of the gas channel design and the backing carbon paper were carried out in a 200 cm{sup 2} x 20-cell module and 36-cell module. Dependence of air utilization on module performance was remarkably improved and power density of more than 0.3 W/cm{sup 2}more » was achieved in spite of the platinum amount in the cells was decreased to 1.1 Mg/cm{sup 2}.« less

Oil recovery method utilizing glyceryl ether sulfonates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naylor, C.G.

1984-03-13

Petroleum may be recovered from petroleum containing formations having high salinity and/or high temperature by injecting into the formation an aqueous fluid containing an effective amount of a surface active agent characterized by the formula: R-O-(A-O)N-(CH2-CH(-CH2-O-CH2-CH2-SO3X)-O)M-H wherein R is an alkyl or alkylaryl radical, AO is an alkylene oxide radical, n is an integer of from 1 to 50, m is an integer from 1 to 10 and X is a sodium, potassium or ammonium cation.

Molecular and Genetic Investigation of Tau in Chronic Traumatic Encephalopthy

DTIC Science & Technology

2016-10-01

Very wide blood vessels, but no gliosis, macrophages, or tangles. 6 Controls Heavy retraction around vessels and high amounts of cell shrinkage...neocortical pyramidal neuron. (B) This neuron contains a mature intracellular tangle. (C) In the white matter, scattered small granular retraction balls

Geoenvironmental impacts of using high carbon fly ash in structural fill applications.

DOT National Transportation Integrated Search

2013-03-01

Fly ash produced by power plants in the United States occasionally contains significant amounts of unburned carbon due to the : use of the increased prevalence of low nitrogen-oxide and sulphur-oxide burners in recent years. This ash cannot be reused...

Oxidation resistant filler metals for direct brazing of structural ceramics

DOEpatents

Moorhead, Arthur J.

1986-01-01

A method of joining ceramics and metals to themselves and to one another is described using essentially pure trinickel aluminide and trinickel aluminide containing small amounts of carbon. This method produces strong joints that can withstand high service temperatures and oxidizing environments.

Identification of high-mannose and multiantennary complex-type N-linked glycans containing alpha-galactose epitopes from Nurse shark IgM heavy chain.

PubMed

Harvey, David J; Crispin, Max; Moffatt, Beryl E; Smith, Sylvia L; Sim, Robert B; Rudd, Pauline M; Dwek, Raymond A

2009-11-01

MALDI-TOF mass spectrometry, negative ion nano-electrospray MS/MS and exoglycosidase digestion were used to identify 36 N-linked glycans from 19S IgM heavy chain derived from the nurse shark (Ginglymostoma cirratum). The major glycan was the high-mannose compound, Man(6)GlcNAc(2) accompanied by small amounts of Man(5)GlcNAc(2), Man(7)GlcNAc(2) and Man(8)GlcNAc(2). Bi- and tri-antennary (isomer with a branched 3-antenna) complex-type glycans were also abundant, most contained a bisecting GlcNAc residue (beta1-->4-linked to the central mannose) and with varying numbers of alpha-galactose residues capping the antennae. Small amounts of monosialylated glycans were also found. This appears to be the first comprehensive study of glycosylation in this species of animal. The glycosylation pattern has implications for the mechanism of activation of the complement system by nurse shark IgM.

Sicklepod (Senna obtusifolia) seed processing and potential utilization.

PubMed

Harry-O'kuru, Rogers E; Wu, Y Victor; Evangelista, Roque; Vaughn, Steven F; Rayford, Warren; Wilson, Richard F

2005-06-15

Sicklepod (Senna obtusifolia) is a leguminous plant that infests soybean fields in the southeastern United States. Its seeds contain a variety of toxic, highly colored compounds, mainly anthraquinones together with a small amount of fat. These compounds contaminate and lower the quality of soybean oil when inadequately cleaned soybean seed from this area is processed. The sorting of sicklepod seed from a soybean harvest is an additional economic burden on the farmer beyond the cost of proper disposal of the weed seed to avoid worsening field infestation. Fortunately, sicklepod seed also contains substantial amounts of carbohydrates and proteins. These edible components when freed from anthraquinones have a market in pet food as well as potential in human foods because of the high galactomannan ratio of the polysaccharides. Sicklepod seed was dehulled, and the ground endosperm was defatted, followed by sequential solvent extraction of the defatted seed meal to isolate the anthraquinones, carbohydrates, and protein components into their respective classes. Each class of isolate was spectroscopically identified.

Cellulose triacetate, thin film dielectric capacitor

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

1995-01-01

Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

Cellulose triacetate, thin film dielectric capacitor

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

1993-01-01

Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

A resistant predator and its toxic prey: persistence of newt toxin leads to poisonous (not venomous) snakes.

PubMed

Williams, Becky L; Brodie, Edmund D; Brodie, Edmund D

2004-10-01

The common garter snake (Thamnophis sirtalis) preys upon the rough-skinned newt (Taricha granulosa), which contains the neurotoxin tetrodotoxin (TTX) in the skin. TTX is toxic, large quantities are present in a newt, and highly resistant snakes have the ability to ingest multiple newts; subsequently snakes harbor significant amounts of active toxin in their own tissues after consuming a newt. Snakes harbor TTX in the liver for 1 mo or more after consuming just one newt, and at least 7 wk after consuming a diet of newts. Three weeks after eating one newt, snakes contained an average of 42 microg of TTX in the liver. This amount could severely incapacitate or kill avian predators, and mammalian predators may be negatively affected as well.

High Temperature Solid Lubricant Coating for High Temperature Wear Applications

NASA Technical Reports Server (NTRS)

DellaCorte, Christopher (Inventor); Edmonds, Brian J (Inventor)

2014-01-01

A self-lubricating, friction and wear reducing composite useful over a wide temperature range is described herein. The composite includes metal bonded chromium oxide dispersed in a metal binder having a substantial amount of nickel. The composite contains a fluoride of at least one Group I, Group II, or rare earth metal, and optionally a low temperature lubricant metal.

Detection of tiny amounts of fissile materials in large-sized containers with radioactive waste

NASA Astrophysics Data System (ADS)

Batyaev, V. F.; Skliarov, S. V.

2018-01-01

The paper is devoted to non-destructive control of tiny amounts of fissile materials in large-sized containers filled with radioactive waste (RAW). The aim of this work is to model an active neutron interrogation facility for detection of fissile ma-terials inside NZK type containers with RAW and determine the minimal detectable mass of U-235 as a function of various param-eters: matrix type, nonuniformity of container filling, neutron gen-erator parameters (flux, pulse frequency, pulse duration), meas-urement time. As a result the dependence of minimal detectable mass on fissile materials location inside container is shown. Nonu-niformity of the thermal neutron flux inside a container is the main reason of the space-heterogeneity of minimal detectable mass in-side a large-sized container. Our experiments with tiny amounts of uranium-235 (<1 g) confirm the detection of fissile materials in NZK containers by using active neutron interrogation technique.

Occurrence of tetrodotoxin-binding high molecular weight substances in the body fluid of shore crab (Hemigrapsus sanguineus).

PubMed

Shiomi, K; Yamaguchi, S; Kikuchi, T; Yamamori, K; Matsui, T

1992-12-01

The shore crab (Hemigrapsus sanguineus) is highly resistant to tetrodotoxin (TTX) although it contains no detectable amount of TTX (less than 5 MU/g, where 1 MU is defined as the amount of TTX killing a 20 g mouse in 30 min). Its body fluid was examined for neutralizing effects against the lethal activity of TTX. When the mixture of the body fluid and TTX was injected i.p. into mice, the lethal activity of TTX was significantly reduced; 1 ml of the body fluid was evaluated to neutralize 3.6-4.0 MU of TTX. Higher neutralizing activity (7.2-12.5 MU/ml of the body fluid) was exhibited by i.v. administration of the body fluid into mice before or after i.p. challenge of TTX. The lethal effect of paralytic shellfish poisons was not counteracted by the body fluid. Analysis by gel filtration on Sepharose 6B revealed that the body fluid contained TTX-binding high mol. wt substances (> 2,000,000) responsible for the neutralizing activity of the body fluid against TTX, which accounts for the high resistibility of the crab to TTX. When the crude toxin extracted from the liver of puffer (Takifugu niphobles) was mixed with the body fluid and chromatographed on Sepharose 6B, almost pure TTX was obtained from the fractions containing the TTX-binding high mol. wt substances, suggesting that the TTX-binding high mol. wt substances could be useful in purification of TTX from biological samples.

Dual-phase Cr-Ta alloys for structural applications

DOEpatents

Liu, Chain T.; Brady, Michael P.; Zhu, Jiahong; Tortorelli, Peter F.

2001-01-01

Dual phase alloys of chromium containing 2 to 11 atomic percent tantalum with minor amounts of Mo, Cr, Ti, Y, La, Cr, Si and Ge are disclosed. These alloys contain two phases including Laves phase and Cr-rich solid solution in either eutectic structures or dispersed Laves phase particles in the Cr-rich solid solution matrix. The alloys have superior mechanical properties at high temperature and good oxidation resistance when heated to above 1000.degree. C. in air.

Two-dimensional high-performance liquid chromatographic determination of day-night variation of D-alanine in mammals and factors controlling the circadian changes.

PubMed

Karakawa, Sachise; Miyoshi, Yurika; Konno, Ryuichi; Koyanagi, Satoru; Mita, Masashi; Ohdo, Shigehiro; Hamase, Kenji

2013-10-01

D-Alanine (D-Ala) is one of the naturally occurring D-amino acids in mammals, and its amount is known to have characteristic circadian changes. It is a candidate for a novel physiologically active substance and/or a biomarker, and the regulation mechanisms of the intrinsic amounts of D-Ala are expected to be clarified. In the present study, the effects of the possible factors controlling the D-Ala amounts, e.g., diet, D-amino acid oxidase (DAO) and intestinal bacteria, on the day-night changes in the intrinsic D-Ala amounts have been investigated using a highly sensitive and selective two-dimensional high-performance liquid chromatographic system combining a reversed-phase column and an enantioselective column. The circadian rhythm was not changed under fasting conditions. In the mice lacking D-amino acid oxidase activity (ddY/DAO(-) mice), clear day-night changes were still observed, suggesting that the factors controlling the D-Ala rhythm were not their food and DAO activity. On the other hand, in the germ-free mice, quite low amounts of D-Ala were detected compared with those in the control mice, indicating that the main origin of D-Ala in the mice is intestinal bacteria. Because the D-Ala amounts in the digesta containing intestinal bacteria did not show the day-night changes, the controlling factor of the circadian changes of the D-Ala amount was suggested to be the intestinal absorption.

Maternal educational level and preschool children's consumption of high-calorie snacks and sugar-containing beverages: mediation by the family food environment.

PubMed

Wijtzes, Anne I; Jansen, Wilma; Jansen, Pauline W; Jaddoe, Vincent W V; Hofman, Albert; Raat, Hein

2013-11-01

To examine the associations between maternal educational level and preschoolers' consumption of high-calorie snacks and sugar-containing beverages, and to assess the mediating effects of variables relating to the family food environment. We analyzed data from 2814 native Dutch preschoolers enrolled in a birth cohort study in Rotterdam (the Netherlands), between 2002 and 2006. Logistic regression models were used to calculate odds ratios of snacking ≥ 2 times/day and consuming sugar-containing beverages ≥ 3 glasses/day for children of mothers with low, mid-low, and mid-high educational levels (reference group: high educational level), before and after adjustment for mediators. Children of low and mid-low educated mothers were significantly more likely to consume excessive amounts of high-calorie snacks and sugar-containing beverages compared with children of high educated mothers, with the highest odds in children of low educated mothers (OR: 2.44; 95% CI: 1.84, 3.23 and OR: 2.46; 95% CI: 1.87, 3.24 respectively). Parental feeding practices, parental consumption of sugar-containing beverages, and children's television time partly explained these associations. Maternal educational level is inversely related to preschoolers' consumption of high-calorie snacks and sugar-containing beverages. Targeting the family food environment may be an effective way of reducing educational inequalities in children's unhealthy dietary behaviors. © 2013.

The (Nutrition Education) Gospel According to NDC.

ERIC Educational Resources Information Center

Kilburn, Eric

1978-01-01

Discusses the flaws in nutrition education as presented by the National Dairy Council (NDC). Those discussed include the presentation of diets that contain high amounts of sugar and cholesterol and the failure to connect diet to heart disease. Suggests ways of monitoring these materials in the schools. (MA)

Biodiesel production by two-stage transesterification with ethanol by washing with neutral water and water saturated with carbon dioxide.

PubMed

Mendow, G; Veizaga, N S; Sánchez, B S; Querini, C A

2012-08-01

Industrial production of ethyl esters is impeded by difficulties in purifying the product due to high amounts of soap formed during transesterification. A simple biodiesel wash process was developed that allows successful purification of samples containing high amounts of soap. The key step was a first washing with neutral water, which removed the soaps without increasing the acidity or affecting the process yield. Afterward, the biodiesel was washed with water saturated with CO(2), a mild acid that neutralized the remaining soaps and extracted impurities. The acidity, free-glycerine, methanol and soaps concentrations were reduced to very low levels with high efficiency, and using non-corrosive acids. Independently of the initial acidity, it was possible to obtain biodiesel within EN14214 specifications. The process included the recovery of soaps by hydrolysis and esterification, making it possible to obtain the theoretical maximum amount of biodiesel. Copyright © 2012 Elsevier Ltd. All rights reserved.

Solid-State NMR Investigation of Bio-chars Produced from Biomass Components and Whole Biomasses

DOE PAGES

Ben, Haoxi; Hao, Naijia; Liu, Qian; ...

2017-08-24

Bio-char is a by-product from thermochemical treatment of biomass and has been identified as an energy condensed product with a comparable heating value as commercial coal. However, the combustion of such solid product as an energy resource is only a preliminary application. It is highly possible to convert bio-char, which always has a condensed aromatic and porous structure to various high-value products. The investigations of the structures and formation pathways for the bio-char are very important to any future applications. In this study, six different biomass components, including cellulose, lignin, and tannin, and three whole biomasses—pine wood, pine residue, andmore » pine bark—have been used to produce bio-char at 400, 500, and 600 °C. Solid-state NMR and FT-IR have been employed in this study to characterize the structures for the bio-chars. The results indicated that the bio-chars produced from lignin contained some methoxyl groups, and the bio-chars produced from tannin contained significantly higher amount of phenolic hydroxyl groups. Compared to the bio-chars produced from pine wood and residue, the bio-chars produced from pine bark contained more aromatic C–O bonds, and aliphatic C–O and C–C bonds, which may be due to the significantly higher amount of lignin and tannin in the pine bark. Furthermore, the elevated amounts of aromatic C–O and aliphatic C–O and C–C bonds in the bio-chars from pine bark appeared to be completely decomposed at 600 °C.« less

Solid-State NMR Investigation of Bio-chars Produced from Biomass Components and Whole Biomasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben, Haoxi; Hao, Naijia; Liu, Qian

Bio-char is a by-product from thermochemical treatment of biomass and has been identified as an energy condensed product with a comparable heating value as commercial coal. However, the combustion of such solid product as an energy resource is only a preliminary application. It is highly possible to convert bio-char, which always has a condensed aromatic and porous structure to various high-value products. The investigations of the structures and formation pathways for the bio-char are very important to any future applications. In this study, six different biomass components, including cellulose, lignin, and tannin, and three whole biomasses—pine wood, pine residue, andmore » pine bark—have been used to produce bio-char at 400, 500, and 600 °C. Solid-state NMR and FT-IR have been employed in this study to characterize the structures for the bio-chars. The results indicated that the bio-chars produced from lignin contained some methoxyl groups, and the bio-chars produced from tannin contained significantly higher amount of phenolic hydroxyl groups. Compared to the bio-chars produced from pine wood and residue, the bio-chars produced from pine bark contained more aromatic C–O bonds, and aliphatic C–O and C–C bonds, which may be due to the significantly higher amount of lignin and tannin in the pine bark. Furthermore, the elevated amounts of aromatic C–O and aliphatic C–O and C–C bonds in the bio-chars from pine bark appeared to be completely decomposed at 600 °C.« less

Graphite intercalation compound with iodine as the major intercalate

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh; Kucera, Donald

1994-01-01

Halogenated graphite CBr(x)I(y) (I less than y/x less than 10) was made by exposing graphite materials to either pure Br2 or an I2/Br2/HBr mixture to initiate the reaction, and then to iodine vapor containing a small amount of Br2/HBr/IBr to complete the intercalation reaction. Wetting of the graphite materials by the I2/Br2/HBr mixture is needed to start the reaction, and a small amount of Br2/HBr/IBr is needed to complete the charge transfer between iodine and carbon. The interplanar spacings for the graphite materials need to be in the 3.35 to 3.41 A range. The X-ray diffraction data obtained from the halogenated HOPG indicate that the distance between the two carbon layers containing intercalate is 7.25 A. Electrical resistivity of the fiber product is from 3 to 6.5 times the pristine value, The presence of a small amount of isoprene rubber in the reaction significantly increased the iodine-to-bromine ratio in the product. In this reaction, rubber is known to generate HBr and to slowly remove bromine from the vapor. The halogenation generally caused a 22 percent to 25 percent weight increase. The halogens were found uniformly distributed in the product interior. However, although the surface contains very little iodine, it has high concentrations of bromine and oxygen. It is believed that the high concentrations of bromine and oxygen in this surface cause the halogenated fiber to be more resistant to structural damage during subsequent fluorination to fabricate graphite fluoride fibers.

Public water supplies in western Texas

USGS Publications Warehouse

Broadhurst, W.L.; Sundstrom, R.W.; Weaver, D.E.

1951-01-01

This report gives a summarized description of the public water supplies in a region comprising 81 counties of western Texas and lying generally west of the hundredth meridian. It is the fourth and last of this series of reports concerning the public water supplies of the State. It gives the available data for each of 142 communities, as follows: The population of the community; the name of the official from whom the information was obtained; the ownership of the waterworks, whether private or municipal; the source of supply, whether ground water or surface water; the amount of water consumed; the facilities for storage; the number of customers served; the character of the chemical and sanitary treatment of the water, if any; and the chemical analyses of the water. Where ground water is used the following also are given. Records of wells, including drillers' logs; character of the pumping equipment; and yield of the wells and water-level records where they are available. Of the 142 public supplies, 133 are obtained from ground water, 5 from surface water, and 4 from a combination of both. The total amount of water . used for public supply in the region averages about 78,000,000 gallons a day. Of this about 61,000,000 gallons a day is ground water and about 17,000,000 gallons a day is surface water. The ground-water resources of the region from which public water supplies are drawn are in rocks that range in age from Permian to Quaternary. The Ogallala formation of Tertiary age (Pliocene), which covers about 35,000 square miles of the High Plains in Texas, is the most important ground-water reservoir in the region. The formation furnishes water for 78 public supplies and for irrigating about 1,000,000 acres of land. The amount of water used for irrigating amounted to about 1,000,000 acre-feet in 1948. The Trinity and Fredericksburg groups of Lower Cretaceous age supply ground water in the western part of the Edwards Plateau, which constitutes an area of more than 22,000 square miles. These formations furnish small to large supplies to 20 municipalities. Sands of the Dockum group of Triassic refurnish meager to moderate supplies of water for 10 municipalities in areas east of the southern part of the High Plains and in the northern Pecos Valley in Texas. Local alluvial, bolson, or volcanic deposits furnish ground water in small to large amounts in scattered localities in the remainder of the region. The Permian rocks are of little importance as a source of ground water for public supply, owing to the highly mineralized water in them. The results of the chemical analyses of 206 samples of water obtained from the public supplies of the region are given in this report. The analyses are reported in parts per million and in equivalents per million for those ions entering into ionic balance. Of the samples analyzed 57 percent contained silica in excess of 20 parts per million; about 9 percent contained iron in excess of 0.3 part per million; 78 percent had hardness in excess of 200 parts per million; about 18 percent contained sulfate in excess of 250 parts per million; 10 percent contained chloride in excess of 250 parts per million; 3 percent contained nitrate in excess of 20 parts per million; 37 percent contained fluoride in excess of 2 parts per million; and 12 percent contained dissolved solids in excess of 1,000 parts per million.

Evaluation of nutraceutical and antinutritional properties in barnyard and finger millet varieties grown in Himalayan region.

PubMed

Panwar, Priyankar; Dubey, Ashutosh; Verma, A K

2016-06-01

Five elite varieties of barnyard (Echinochloa frumentacea) and finger (Eleusine coracana) growing at northwestern Himalaya were investigated for nutraceutical and antinutritional properties. Barnyard millet contained higher amount of crude fiber, total dietary fiber, tryptophan content, total carotenoids, α-tocopherol compared to the finger millet whereas the finger millet contains higher amount of methionine and ascorbic acid as compared to the barnyard millet. The secondary metabolites of biological functions were analyzed and found that barnyard millet contained the higher amount of polyphenols, tannins and ortho-dihydroxy phenol content compared to finger millet. Among antinutitional compounds barnyard millet contained lower phytic acid content compare to finger millet whereas no significant difference in trypsin inhibition activity of barnyard millet and finger millet varieties were found. Barnyard millet contained higher acid phosphatase, α-galactosidase and α-amylase inhibitor activity compared to finger millet. Finger millet seeds contained about 10-13 folds higher calcium content and double amount of manganese content in comparison to barnyard millet seeds. Present study suggests that barnyard millet varieties studied under present investigation were found nutritionally superior compared to finger millet varieties.

Simultaneous Determination of Pyridoxine and Riboflavin in Energy Drinks by High-Performance Liquid Chromatography with Fluorescence Detection

ERIC Educational Resources Information Center

Martí-Andre´s, P.; Escuder-Gilabert, L.; Martín-Biosca, Y.; Sagrado, S.; Medina-Herna´ndez, M.J.

2015-01-01

Energy drinks, as familiar consumer products, have been widely used in laboratory courses to help promote student interest, as well as to connect lecture concepts with laboratory work. Energy drinks contain B vitamins: pyridoxine (vitamin B6) and riboflavin (vitamin B2) of which amounts are high enough to be of concern. In this work, a fast and…

Evaluation of the Botanical Authenticity and Phytochemical Profile of Black Cohosh Products by High-Performance Liquid Chromatography with Selected Ion Monitoring Liquid Chromatography–Mass Spectrometry

PubMed Central

Jiang, Bei; Kronenberg, Fredi; Nuntanakorn, Paiboon; Qiu, Ming-Hua; Kennelly, Edward J.

2011-01-01

Black cohosh (Actaea racemosa L., syn. Cimicifuga racemosa L.) has become increasingly popular as a dietary supplement in the United States for the treatment of symptoms related to menopause, but the botanical authenticity of most products containing black cohosh has not been evaluated, nor is manufacturing highly regulated in the United States. In this study, 11 black cohosh products were analyzed for triterpene glycosides, phenolic constituents, and formononetin by high-performance liquid chromatography–photodiode array detection and a new selected ion monitoring liquid chromatography–mass spectrometry method. Three of the 11 products were found to contain the marker compound cimifugin and not cimiracemoside C, thereby indicating that these plants contain Asian Actaea instead of black cohosh. One product contained both black cohosh and an Asian Actaea species. For the products containing only black cohosh, there was significant product-to-product variability in the amounts of the selected triterpene glycosides and phenolic constituents, and as expected, no formononetin was detected. PMID:16637680

Separation of thorium ions from wolframite and scandium concentrates using graphene oxide.

PubMed

Jankovský, Ondřej; Sedmidubský, David; Šimek, Petr; Klímová, Kateřina; Bouša, Daniel; Boothroyd, Chris; Macková, Anna; Sofer, Zdeněk

2015-10-14

The separation of rare metals from the ores and commercially available compounds is an important issue due to the need of their high purity in advanced materials and devices. Important examples of two highly important elements that co-exist in the ores are scandium and thorium. Scandium containing ores and consequently also commercially available scandium compounds often contain traces of thorium which is very difficult to separate. We used graphene oxide for the selective sorption of thorium ions from scandium and thorium mixtures originating from the mined ores as well as from commercially available scandium salts. Our results showed that graphene oxide has an extreme affinity towards thorium ions. After the sorption process the graphene oxide contained over 20 wt% of thorium while the amount of scandium sorbed on GO was very low. This phenomenon of high sorption selectivity of graphene oxide can be applied in industry for the purification of various chemicals containing scandium and for separation of thorium containing mixtures. Alternatively, this methodology can be used for preconcentration of thorium from low-grade ores and its further use in the new generation of nuclear reactors.

Mixing and compaction recommendations for warm mix asphalt (WMA) with recycled asphalt shingles (RAS) : final report.

DOT National Transportation Integrated Search

2017-05-01

The use of recycled asphalt shingles (RAS) is an attractive option for asphalt mixture producers due to the : high amount of recycled asphalt binder available in RAS. By weight, RAS contains 10 to 25% asphalt by total : weight of the shingle. The asp...

Impact of acid precipitation on freshwater ecosystems on Norway

Treesearch

Richard F. Wright; Torstein Dale; Egil T. Gjessing; George R. Hendrey; Arne Henriksen; Merete Johannessen; Ivar P. Muniz

1976-01-01

Extensive studies of precipitation chemistry during the last 20 years have clearly shown that highly polluted precipitation falls over large areas of Scandinavia, and that this pollution is increasing in severity and geographical extent. Precipitation in southern Norway, Sweden, and Finland contains large amounts of H+, SO4...

Ionization monitor with improved ultra-high megohm resistor

DOEpatents

Burgess, Edward T.

1988-11-05

An ionization monitor measures extremely small currents using a resistor containing a beta emitter to generate ion-pairs which are collected as current when the device is used as a feedback resistor in an electrometer circuit. By varying the amount of beta emitter, the resistance of the resistor may be varied.

High-oleic ready-to-use therapeutic food maintains docosahexaenoic acid status in severe malnutrition

USDA-ARS?s Scientific Manuscript database

Ready-to-use therapeutic food (RUTF) is the preferred treatment for uncomplicated severe acute malnutrition. It contains large amounts of linoleic acid and little a-linolenic acid, which may reduce the availability of docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) to the recovering child...

Engineering the production of conjugated fatty acids in Arabidopsis thaliana leaves

USDA-ARS?s Scientific Manuscript database

The seeds of many non-domesticated plant species synthesize oils containing high amounts of a single unusual fatty acid, many of which have potential usage in industry. Despite the identification of enzymes for unusual oxidized fatty acid synthesis, the production of these fatty acids in engineered ...

Effect of tomato extract supplementation against high-fat diet-induced hepatic lesions

USDA-ARS?s Scientific Manuscript database

Higher intake of tomatoes or tomato-based products has been associated with lower risk for liver cancer. In this study, we investigated the effects of supplementing tomato extract (TE), which contains mainly lycopene (LY) and less amounts of its precursors, phytoene (PT) and phytofluene (PTF) agains...

Self-contained microfluidic systems: a review.

PubMed

Boyd-Moss, Mitchell; Baratchi, Sara; Di Venere, Martina; Khoshmanesh, Khashayar

2016-08-16

Microfluidic systems enable rapid diagnosis, screening and monitoring of diseases and health conditions using small amounts of biological samples and reagents. Despite these remarkable features, conventional microfluidic systems rely on bulky expensive external equipment, which hinders their utility as powerful analysis tools outside of research laboratories. 'Self-contained' microfluidic systems, which contain all necessary components to facilitate a complete assay, have been developed to address this limitation. In this review, we provide an in-depth overview of self-contained microfluidic systems. We categorise these systems based on their operating mechanisms into three major groups: passive, hand-powered and active. Several examples are provided to discuss the structure, capabilities and shortcomings of each group. In particular, we discuss the self-contained microfluidic systems enabled by active mechanisms, due to their unique capability for running multi-step and highly controllable diagnostic assays. Integration of self-contained microfluidic systems with the image acquisition and processing capabilities of smartphones, especially those equipped with accessory optical components, enables highly sensitive and quantitative assays, which are discussed. Finally, the future trends and possible solutions to expand the versatility of self-contained, stand-alone microfluidic platforms are outlined.

Compositional variations for alpha-galactosides in different species of leguminosae, brassicaceae, and barley: a chemotaxonomic study based on chemometrics and high-performance capillary electrophoresis.

PubMed

Andersen, Keld Ejdrup; Bjergegaard, Charlotte; Møller, Peter; Sørensen, Jens Christian; Sørensen, Hilmer

2005-07-13

The contents of raffinose family oligosaccharides (RFO) and sucrose in Brassica, Lupinus, Pisum, and Hordeum species were investigated by chemometric principal component analysis (PCA). Hordeum samples contained sucrose and raffinose, and Brassica samples all contained sucrose, raffinose, and stachyose. In addition to these, the Pisum samples contained verbascose and the Lupinus samples also contained ajugose. High stachyose and low ajugose contents were found in Lupinus albus in contrast to Lupinus angustifolius, having low stachyose and high ajugose contents. Lupinus luteus had average stachyose and ajugose contents, whereas large amounts of verbascose were accumulated in these seeds. Lupinus mutabilis had high stachyose and low ajugose contents, similar to the composition in L. albus but showing higher raffinose content. The Brassica samples also showed compositional RFO variations within the species, and subgroup formations were discovered within the investigated Brassica napus varieties. PCA results indicated compositional variations between the investigated genera and within the various species of value as chemotaxonomic defined parameters and as tools in evaluations of authenticity/falsifications when RFO-containing plants are used as, for example, feed and food additives.

Method for pretreating lignocellulosic biomass

DOEpatents

Kuzhiyil, Najeeb M.; Brown, Robert C.; Dalluge, Dustin Lee

2015-08-18

The present invention relates to a method for pretreating lignocellulosic biomass containing alkali and/or alkaline earth metal (AAEM). The method comprises providing a lignocellulosic biomass containing AAEM; determining the amount of the AAEM present in the lignocellulosic biomass; identifying, based on said determining, the amount of a mineral acid sufficient to completely convert the AAEM in the lignocellulosic biomass to thermally-stable, catalytically-inert salts; and treating the lignocellulosic biomass with the identified amount of the mineral acid, wherein the treated lignocellulosic biomass contains thermally-stable, catalytically inert AAEM salts.

GDP: A new source for shallow high-resolution seismic exploration

NASA Astrophysics Data System (ADS)

Rashed, Mohamed A.

2009-06-01

Gas-Driven Piston (GDP) is a new source for shallow seismic exploration. This source works by igniting a small amount of gas inside a closed chamber connected to a vertical steel cylinder. The gas explosion drives a steel piston, mounted inside the cylinder, downward so that the piston's thick head hits a steel base at the end of the cylinder generating a strong shock wave into the ground. Experimental field tests conducted near Ismailia, Egypt, prove that the portable, inexpensive and environmentally benign GDP generates stronger seismic waves than the sledgehammer that is commonly used in shallow seismic exploration. Tests also show that GDP is a highly repeatable and controllable and that its seismic waves contain a good amount of high frequencies which makes the GDP an excellent source for shallow seismic exploration.

Pelletizing lignite

DOEpatents

Goksel, Mehmet A.

1983-11-01

Lignite is formed into high strength pellets having a calorific value of at least 9,500 Btu/lb by blending a sufficient amount of an aqueous base bituminous emulsion with finely-divided raw lignite containing its inherent moisture to form a moistened green mixture containing at least 3 weight % of the bituminous material, based on the total dry weight of the solids, pelletizing the green mixture into discrete green pellets of a predetermined average diameter and drying the green pellets to a predetermined moisture content, preferrably no less than about 5 weight %. Lignite char and mixture of raw lignite and lignite char can be formed into high strength pellets in the same general manner.

Identifying Ca2+-Binding Sites in Proteins by Liquid Chromatography-Mass Spectrometry Using Ca2+-Directed Dissociations

PubMed Central

Jamalian, Azadeh; Sneekes, Evert-Jan; Wienk, Hans; Dekker, Lennard J. M.; Ruttink, Paul J. A.; Ursem, Mario; Luider, Theo M.; Burgers, Peter C.

2014-01-01

Here we describe a new method to identify calcium-binding sites in proteins using high-resolution liquid chromatography-mass spectrometry in concert with calcium-directed collision-induced dissociations. Our method does not require any modifications to the liquid chromatography-mass spectrometry apparatus, uses standard digestion protocols, and can be applied to existing high-resolution MS data files. In contrast to NMR, our method is applicable to very small amounts of complex protein mixtures (femtomole level). Calcium-bound peptides can be identified using three criteria: (1) the calculated exact mass of the calcium containing peptide; (2) specific dissociations of the calcium-containing peptide from threonine and serine residues; and (3) the very similar retention times of the calcium-containing peptide and the free peptide. PMID:25023127

Phenolic composition of the edible parts (flesh and skin) of Bordô grape (Vitis labrusca) using HPLC-DAD-ESI-MS/MS.

PubMed

Lago-Vanzela, Ellen Silva; Da-Silva, Roberto; Gomes, Eleni; García-Romero, Esteban; Hermosín-Gutiérrez, Isidro

2011-12-28

The aim of this study was the detailed characterization of the phenolic composition and the determination of the antioxidant activity of the Bordô grape (Vitis labrusca) cultivated in South Brazil. The edible parts of Bordô grapes (flesh and skin) contained 1130 mg/kg of total phenolic compounds (as gallic acid), mainly located in the skins. Anthocyanin content in the skins was high, largely as 3,5-diglucosides (1359 mg/kg, as malvidin 3,5-diglucoside). Total flavonols accounted for 154 μmol/kg, mainly located in the skins and with myricetin 3-glucoside as the principal flavonol in both grape parts. Very low amounts of flavan-3-ol monomers and dimers and low amounts of polymeric proanthocyanidins, with a composition similar to that reported for V. vinifera grape varieties, were found in Bordô grape skins. Hydroxycinnamic acid derivatives mainly derived from caffeic acid and were found in the skins in high amounts, ten times higher than in the flesh (total amount: 483 μmol/kg). Finally, the Bordô grape cultivar can be considered a high resveratrol producer (10.91 mg/kg) and also exhibited a high value of total antioxidant capacity (37.6 ± 1.0 mmol/kg, as Trolox).

Short-term nutritional strategies before slaughter are effective in modulating the final pH and color of broiler breast meat.

PubMed

Guardia, Sarah; Lessire, Michel; Corniaux, Alain; Métayer-Coustard, Sonia; Mercerand, Frédéric; Tesseraud, Sophie; Bouvarel, Isabelle; Berri, Cécile

2014-07-01

The poultry meat industry is faced with various quality issues related to variations in the ultimate pH of breast meat. The aim of this study was to evaluate the possibility to control breast ultimate pH by distributing finishing diets varying in amino acid (AA) and energy content for a short period before slaughter. Experimental diets were distributed to PM3 broilers on the last 3 d before slaughter (36 d of age). They consisted of a control (C) diet (3,150 kcal/kg; 200 g/kg of CP; 10.0 g/kg of true digestible Lys) with adequate amounts of AA other than Lys, 6 diets isocaloric to the control diet including 3 Lys-deficient (8.0 g/kg) diets with an adequate (Lys-/AA), low (Lys-/AA-), or high (Lys-/AA+) amount of other essential AA calculated in relation to Lys, and 3 Lys-rich (12.0 g/kg) diets with an adequate (Lys+/AA), low (Lys+/AA-), or high (Lys+/AA+) amount of other essential AA calculated in relation to Lys, and 2 diets isoproteic to C with a high (3,300 kcal/kg, E+) or low (3,000 kcal/kg, E-) energy content. Broiler feed consumption and growth performance were slightly affected by AA and energy content during the finishing period. Feed intake (33-36 d) was lower with the Lys+/AA+ and E+, and FCR between 24 and 36 d was higher with the Lys-/AA- and E- than with the C diet. Body weight at d 36 was lower in Lys-/AA-, Lys+/AA+, and E+ than in C, whereas the breast meat yield and abdominal fatness were not affected by diet. Lower pH values were observed in broilers fed Lys-deficient diets containing a high amount of other AA (Lys-/AA+) than in broilers fed diets containing low (AA-) or adequate (AA) amounts of other AA. This study shows that it is possible to alter the pH of breast meat by changing AA profile over a short period before slaughter, with limited impact on broiler growth and carcass composition. © 2014 Poultry Science Association Inc.

Mercury methylation in mine wastes collected from abandoned mercury mines in the USA

USGS Publications Warehouse

Gray, J.E.; Hines, M.E.; Biester, H.; Lasorsa, B.K.; ,

2003-01-01

Speciation and transformation of Hg was studied in mine wastes collected from abandoned Hg mines at McDermitt, Nevada, and Terlingua, Texas, to evaluate formation of methyl-Hg, which is highly toxic. In these mine wastes, we measured total Hg and methyl-Hg contents, identified various Hg compounds using a pyrolysis technique, and determined rates of Hg methylation and methyl-Hg demethylation using isotopic-tracer methods. Mine wastes contain total Hg contents as high as 14000 ??g/g and methyl-Hg concentrations as high as 88 ng/g. Mine wastes were found to contain variable amounts of cinnabar, metacinnabar, Hg salts, Hg0, and Hg0 and Hg2+ sorbed onto matrix particulates. Samples with Hg0 and matrix-sorbed Hg generally contained significant methyl-Hg contents. Similarly, samples containing Hg0 compounds generally produced significant Hg methylation rates, as much as 26%/day. Samples containing mostly cinnabar showed little or no Hg methylation. Mine wastes with high methyl-Hg contents generally showed low methyl-Hg demethylation, suggesting that Hg methylation was dominant. Methyl-Hg demethylation was by both oxidative and microbial pathways. The correspondence of mine wastes containing Hg0 compounds and measured Hg methylation suggests that Hg0 oxidizes to Hg2+, which is subsequently bioavailable for microbial Hg methylation.

Composition and molecular weight distribution of carob germ protein fractions.

PubMed

Smith, Brennan M; Bean, Scott R; Schober, Tilman J; Tilley, Michael; Herald, Thomas J; Aramouni, Fadi

2010-07-14

Biochemical properties of carob germ proteins were analyzed using a combination of selective extraction, reversed-phase high-performance liquid chromatography (RP-HPLC), size exclusion chromatography (SEC) coupled with multiangle laser light scattering (SEC-MALS), and electrophoretic analysis. Using a modified Osborne extraction procedure, carob germ flour proteins were found to contain approximately 32% albumin and globulin and approximately 68% glutelin with no prolamins detected. The albumin and globulin fraction was found to contain low amounts of disulfide-bonded polymers with relatively low M(w) ranging up to 5 x 10(6) Da. The glutelin fraction, however, was found to contain large amounts of high molecular weight disulfide-bonded polymers with M(w) up to 8 x 10(7) Da. When extracted under nonreducing conditions and divided into soluble and insoluble proteins as typically done for wheat gluten, carob germ proteins were found to be almost entirely ( approximately 95%) in the soluble fraction with only ( approximately 5%) in the insoluble fraction. As in wheat, SEC-MALS analysis showed that the insoluble proteins had a greater M(w) than the soluble proteins and ranged up to 8 x 10(7) Da. The lower M(w) distribution of the polymeric proteins of carob germ flour may account for differences in functionality between wheat and carob germ flour.

What's in your Douglas-fir bark?

Treesearch

M. Gabriela Buamscha; James E. Altland

2008-01-01

Douglas-fir bark is a common waste product of forest industry, and has potential use as a substrate in container nurseries. Douglas-fir bark (DFB) is strongly acidic and contains amounts of phosphorus, potassium, iron, copper and manganese within or above the levels recommended for growing container crops. As the pH of DFB decreases, electrical conductivity and amounts...

Synthesis and Compatibility of Ionic Liquid Containing Rod-Coil Polyimide Gel Electrolytes with Lithium Metal Electrodes

NASA Technical Reports Server (NTRS)

Tigelaar, Dean M.; Palker, Allyson E.; Meador, Mary Ann B.; Bennett, William R.

2008-01-01

A highly cross-linked polyimide-polyethylene oxide copolymer has been synthesized that is capable of holding large volumes of liquid component, simultaneously maintaining good dimensional stability. An amine end capped oligomer was made that was imidized in solution, followed by reaction with a triisocyanate in the presence of desired additives at ambient temperature. Polymer films are able to hold over 4 times their weight in room temperature ionic liquid RTIL or carbonate solvent. Electrolytes were studied that contained varying amounts of RTIL, lithium trifluoromethanesulfonimide LiTFSi, and alumina nanoparticles. Electrochemical stability of these electrolytes with lithium metal electrodes was studied by galvanic cycling and impedance spectroscopy. Improved cycling stability and decreased interfacial resistance were observed when increasing amounts of RTIL and LiTFSi were added. The addition of small amounts of alumina further decreased interfacial resistance by nearly an order of magnitude. During the course of the study, cycling stability increased from less than 3 to greater than 1000 h at 60 C and 0.25 mA/cm2 current density.

Method for determining asphaltene stability of a hydrocarbon-containing material

DOEpatents

Schabron, John F; Rovani, Jr., Joseph F

2013-02-05

A method for determining asphaltene stability in a hydrocarbon-containing material having solvated asphaltenes therein is disclosed. In at least one embodiment, it involves the steps of: (a) precipitating an amount of the asphaltenes from a liquid sample of the hydrocarbon-containing material with an alkane mobile phase solvent in a column; (b) dissolving a first amount and a second amount of the precipitated asphaltenes by changing the alkane mobile phase solvent to a final mobile phase solvent having a solubility parameter that is higher than the alkane mobile phase solvent; (c) monitoring the concentration of eluted fractions from the column; (d) creating a solubility profile of the dissolved asphaltenes in the hydrocarbon-containing material; and (e) determining one or more asphaltene stability parameters of the hydrocarbon-containing material.

Identification and Characterization of a High Efficiency Aniline Resistance and Degrading Bacterium MC-01.

PubMed

Yang, Liu; Ying, Chen; Fang, Ni; Zhong, Yao; Zhao-Xiang, Zhong; Yun, Sun

2017-05-01

Biodegradation is one of the important methods for the treatment of industrial wastewater containing aniline. In this paper, a degrading bacterium named MC-01, which could survive in high concentration aniline wastewater, was screened from industrial wastewater containing aniline and sludge. MC-01 was preliminarily identified as Ochrobactrum sp. based on the amplified 16S rDNA gene sequence and Biolog system identification. MC-01 was highly resistant to aniline. After 24-h culture under aniline concentration of 6500 mg/L, the amount of bacterium survived still remained 0.05 × 10 6  CFU/mL. Experiments showed that there was no coupling expression between the growth of MC-01 and aniline degradation. The optimum growth conditions in LB culture were pH 6.0, 30 °C of temperature, and 4% of incubation amount, respectively. And the optimum conditions of aniline degradation of MC-01 were pH 7.0, 45 °C of temperature, and 3.0% of salt concentration, respectively. The degradation rate of MC-01 (48 h) in different aniline concentrations (200~1600 mg/L) was stable under the optimum conditions, which could reach more than 75%.

Analytical method for measuring cosmogenic 35S in natural waters

DOE PAGES

Uriostegui, Stephanie H.; Bibby, Richard K.; Esser, Bradley K.; ...

2015-05-18

Here, cosmogenic sulfur-35 in water as dissolved sulfate ( 35SO 4) has successfully been used as an intrinsic hydrologic tracer in low-SO 4, high-elevation basins. Its application in environmental waters containing high SO 4 concentrations has been limited because only small amounts of SO 4 can be analyzed using current liquid scintillation counting (LSC) techniques. We present a new analytical method for analyzing large amounts of BaSO 4 for 35S. We quantify efficiency gains when suspending BaSO 4 precipitate in Inta-Gel Plus cocktail, purify BaSO 4 precipitate to remove dissolved organic matter, mitigate interference of radium-226 and its daughter productsmore » by selection of high purity barium chloride, and optimize LSC counting parameters for 35S determination in larger masses of BaSO 4. Using this improved procedure, we achieved counting efficiencies that are comparable to published LSC techniques despite a 10-fold increase in the SO 4 sample load. 35SO 4 was successfully measured in high SO 4 surface waters and groundwaters containing low ratios of 35S activity to SO 4 mass demonstrating that this new analytical method expands the analytical range of 35SO 4 and broadens the utility of 35SO 4 as an intrinsic tracer in hydrologic settings.« less

A systematic review of high-oleic vegetable oil substitutions for other fats and oils on cardiovascular disease risk factors: implications for novel high-oleic soybean oils.

PubMed

Huth, Peter J; Fulgoni, Victor L; Larson, Brian T

2015-11-01

High-oleic acid soybean oil (H-OSBO) is a trait-enhanced vegetable oil containing >70% oleic acid. Developed as an alternative for trans-FA (TFA)-containing vegetable oils, H-OSBO is predicted to replace large amounts of soybean oil in the US diet. However, there is little evidence concerning the effects of H-OSBO on coronary heart disease (CHD)(6) risk factors and CHD risk. We examined and quantified the effects of substituting high-oleic acid (HO) oils for fats and oils rich in saturated FAs (SFAs), TFAs, or n-6 (ω-6) polyunsaturated FAs (PUFAs) on blood lipids in controlled clinical trials. Searches of online databases through June 2014 were used to select studies that defined subject characteristics; described control and intervention diets; substituted HO oils compositionally similar to H-OSBO (i.e., ≥70% oleic acid) for equivalent amounts of oils high in SFAs, TFAs, or n-6 PUFAs for ≥3 wk; and reported changes in blood lipids. Studies that replaced saturated fats or oils with HO oils showed significant reductions in total cholesterol (TC), LDL cholesterol, and apolipoprotein B (apoB) (P < 0.05; mean percentage of change: -8.0%, -10.9%, -7.9%, respectively), whereas most showed no changes in HDL cholesterol, triglycerides (TGs), the ratio of TC to HDL cholesterol (TC:HDL cholesterol), and apolipoprotein A-1 (apoA-1). Replacing TFA-containing oil sources with HO oils showed significant reductions in TC, LDL cholesterol, apoB, TGs, TC:HDL cholesterol and increased HDL cholesterol and apoA-1 (mean percentage of change: -5.7%, -9.2%, -7.3%, -11.7%, -12.1%, 5.6%, 3.7%, respectively; P < 0.05). In most studies that replaced oils high in n-6 PUFAs with equivalent amounts of HO oils, TC, LDL cholesterol, TGs, HDL cholesterol, apoA-1, and TC:HDL cholesterol did not change. These findings suggest that replacing fats and oils high in SFAs or TFAs with either H-OSBO or oils high in n-6 PUFAs would have favorable and comparable effects on plasma lipid risk factors and overall CHD risk. © 2015 American Society for Nutrition.

Study on Treatment of acidic and highly concentrated fluoride waste water using calcium oxide-calcium chloride

NASA Astrophysics Data System (ADS)

Ren, T.; Gao, X. R.; Zheng, T.; Wang, P.

2016-08-01

There are problems with treating acidic waste water containing high concentration fluorine by chemical precipitation, including the low sludge setting velocity and the high difficulty of reaching the criterion. In Heilongjiang province, a graphite factory producing high-purity graphite generates acidic waste water with a high concentration of fluorine. In this paper, the effect of removals on the concentration of fluoride with the combined treatment of calcium oxide and calcium chloride were discussed with regard to acid waste water. The study improved the sludge characteristics by using polyacrylamide (PAM) and polymeric aluminum chloride (PAC). The effect of different coagulants on sludge was evaluated by the sludge settlement ratio (SV), sludge volume index (SVI) and sludge moisture content. The results showed that the optimal combination for 100 ml waste water was calcium oxide addition amount of 14 g, a calcium chloride addition amount of 2.5 g, a PAM addition amount of 350 mg/L, and the effluent fluoride concentration was below 6 mg/L. PAM significantly improved the sludge settling velocity. The sludge settlement ratio reduced from 87.6% to 60%. The process for wastewater treatment was easily operated and involved low expenditure.

Orodispersible tablets containing taste-masked solid lipid pellets with metformin hydrochloride: Influence of process parameters on tablet properties.

PubMed

Petrovick, Gustavo Freire; Kleinebudde, Peter; Breitkreutz, Jörg

2018-01-01

Compaction of multiparticulates into tablets, particularly into orodispersible tablets (ODTs), is challenging. The compression of pellets, made by solid lipid extrusion/spheronization processes, presents peculiar difficulties since solid lipids usually soften or melt at relatively low temperature ranges and due to applied mechanical forces. Until now, there are no reports in literature about the development of ODTs based on solid lipid pellets. To investigate the feasibility of producing such tablets, a design of experiment (DoE) approach was performed to elucidate the influence of compression force and amount of two co-processed excipients (Ludiflash ® and Parteck ® ODT) on properties of the tablets (friability, tensile strength, and disintegration time). ODTs (15 mm, flat-faced) with solid lipid pellets (250-1000 µm in diameter) containing 500 mg of metformin HCl, presenting immediate drug release profile and taste-masked properties, were targeted. During compression, a strong lamination of the tablets containing Parteck ® ODT was observed. This phenomenon was prominently observed when high compression forces (≥5 kN) and high excipient amounts (≥40%; w/w) were used. On the other hand, the DoE focused on tablets with Ludiflash ® showed better results regarding the production of ODTs. A positive influence of the compression force on the tensile strength and disintegration time of the tablets, regarding specifications of the Ph. Eur., was observed. The increase in the amount of this excipient resulted in fast disintegrating tablets, however, a negative influence on the tensile strength was noticed. After optimization of the parameters and formulation, based on the DoE results and considering the Ph. Eur. specifications for tablets, ODTs based on lipid pellets containing metformin HCl presenting immediate release profile (85% drug release in less than 30 min) and taste-masked properties (determined by an electronic tongue) were successfully obtained. Copyright © 2017 Elsevier B.V. All rights reserved.

75 FR 50791 - Bureau of Political-Military Affairs: Directorate of Defense Trade Controls; Notifications to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-17

... services in the amount of $50,000,000 or more. The transaction contained in the attached certification... technical data, and defense services in the amount of $50,000,000 or more. The transaction contained in the... $100,000,000 or more. The transaction contained in the attached certification involves the export of...

Dietary docosahexaenoic acid and trans-10, cis-12-conjugated linoleic acid alter oxylipins profiles in mouse adipose tissue

USDA-ARS?s Scientific Manuscript database

Diets containing high amounts of n-3 polyunsaturated fatty acids (PUFA) decrease inflammation and the incidence of chronic diseases including cardiovascular disease and nonalcoholic fatty liver disease while trans-fatty acids (TFA) intake increases the incidence of these conditions. Some n-3 PUFA-a...

Hydrolysis of soybean protein improves iron bioavailability

USDA-ARS?s Scientific Manuscript database

Iron is an important trace metal element in human body. Iron deficiency affects human health, especially pregnant women and children. Soybean protein is a popular food in Asia and can contain a high amount of iron (145.70±0.74 ug/g); however, it is usually reported as an inhibitor of iron absorption...

Productivity of nonindustrial private forests in western Washington: alternative futures.

Treesearch

Ralph J. Alig; Darius M. Adams

1995-01-01

Nonindustrial private timberlands in western Washington have high productive potential and contribute harvest amounts somewhat more than proportional to their area. Of all private ownerships they are influenced the most by land use shifts and are affected in important ways by forest practice regulations. About 1 million acres of nonindustrial private timberland contain...

77 FR 34149 - Heavy-Duty Highway Program: Revisions for Emergency Vehicles and SCR Maintenance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-08

... soot. Since this burning can involve extra heat and/or oxygen or oxygen- containing compounds, this... fuel consumption. This loss in performance may be noticed by the vehicle operator in terms of poor... excessive amounts of trapped PM begin to oxidize at high temperatures (i.e., DPF regeneration temperatures...

Utilization of SNP, SSR, and biochemical data to evaluate genetic and phenotypic diversity in the U.S. peanut germplasm collection.

USDA-ARS?s Scientific Manuscript database

Peanuts (Arachis hypogaea L.) are nutritious because their seeds typically contain high amounts of oil, protein, phytochemicals such as resveratrol, and antioxidants such as tocopherol and folic acid; therefore, they are an important oil seed crop worldwide. The genetic diversity and population stru...

Effects of nitro-treatment on Salmonella, E. coli and nitrogen metabolism during composting of poultry litter

USDA-ARS?s Scientific Manuscript database

Poultry litter contains appreciable amounts of uric acid which makes it a good crude protein supplement for ruminants whose gut microbes transform the nitrogen in uric acid into high quality microbial protein. However, poultry litter must be treated to kill bacterial pathogens before feeding. Pres...

Parent Evaluations of Traditional and Consumer-Focused School Psychoeducational Reports

ERIC Educational Resources Information Center

Hite, John F.

2017-01-01

Completion of pyschoeducational reports account for a significant amount of school psychologists' time. The report findings are often used to make high stakes educational decisions about the child. Parents are one of the main consumers of psychoeducational reports and expected to use the information contained in them to participate in making…

Assessment of oil content and fatty acid composition variability in two economically important Hibiscus species.

USDA-ARS?s Scientific Manuscript database

The Hibiscus genus encompasses more than 300 species, but kenaf (H. cannabinus L.) and roselle (H. sabdariffa L.) are the two most economically important species within the genus. Seeds from these two Hibiscus species contain a relatively high amount of oil with two unusual fatty acids: dihydrosterc...

Dietary exposure to aluminium of urban residents from cities in South China.

PubMed

Jiang, Qi; Wang, Jing; Li, Min; Liang, Xuxia; Dai, Guangwei; Hu, Zhikun; Wen, Jian; Huang, Qiong; Zhang, Yonghui

2013-01-01

A dietary survey was conducted over three consecutive days by using 24-hour dietary recall in the Pearl River Delta of South China to investigate the dietary consumption status. A total of 1702 food samples, 22 food groups, were collected, and aluminium concentrations of foods were determined by using ICP-MS. Weekly dietary exposure to aluminium of the average urban residents of South China was estimated to be 1.5 mg kg⁻¹ body weight, which amounted to 76% of the provisional tolerable weekly intake. Wheat-made products (53.5%) contributed most to the dietary exposure, followed by vegetables (12.2%). The high-level consumers' weekly exposure to aluminium was 11.1 mg kg⁻¹ body weight, which amounted to 407% of the provisional tolerable weekly intake. The results indicated that the general urban residents in South China might be safe from aluminium exposure, but the high-level consumers might be at some risk of aluminium exposure. The foods contributing to aluminium exposure were processed food with aluminium-containing food additives. It is necessary to take effective measures to control the overuse of aluminium-containing food additives.

Tuning the Functional Properties of Bitter Vetch (Vicia ervilia) Protein Films Grafted with Spermidine

PubMed Central

Roviello, Valentina; Sabbah, Mohammed

2017-01-01

Bitter vetch protein films containing positively charged spermidine, alone or with low amounts of glycerol, showed high tensile strength that progressively decreased by increasing the plasticizer concentration. Accordingly, lower film elongation at break and higher Young’s module values were detected in the presence of the polyamine without or with small amounts of glycerol. These data suggest that spermidine not only acts as a plasticizer itself by ionically interacting with proteins, but that it also facilitates glycerol-dependent reduction of the intermolecular forces along the protein chains, consequently improving the film flexibility and extensibility. Thus, spermidine may be considered not only as a primary, but also as a secondary plasticizer because of its ability to enhance glycerol plasticizing performance. Such double behavior of the polyamine was confirmed by the film permeability tests, since spermidine increased the barrier properties to gases and water vapor, while glycerol emphasized this effect at low concentrations but led to its marked reversal at high concentrations. Film microscopic images also substantiated these findings, showing more compact, cohesive, and homogeneous matrices in all spermidine-containing films. PMID:29292733

(GaIn)(NAs) growth using di-tertiary-butyl-arsano-amine (DTBAA)

NASA Astrophysics Data System (ADS)

Sterzer, E.; Ringler, B.; Nattermann, L.; Beyer, A.; von Hänisch, C.; Stolz, W.; Volz, K.

2017-06-01

III/V semiconductors containing small amounts of Nitrogen (N) are very interesting for a variety of optoelectronic applications. Unfortunately, the conventionally used N precursor 1,1-dimethylhydrazine (UDMHy) has an extremely low N incorporation efficiency in GaAs when grown using metal organic vapor phase epitaxy. Alloying Ga(NAs) with Indium (In) even leads to an exponential reduction of N incorporation. The huge amount of UDMHy in turn changes drastically the growth conditions. Furthermore, the application of this material is still hampered by the large carbon incorporation, most probably originating from the metal organic precursors. Hence, novel precursors for dilute nitride growth are needed. This paper will show (GaIn)(NAs) growth studies with the novel precursor di-tertiary-butyl-arsano-amine in combination with tri-ethyl-gallium and tri-methyl-indium. We show an extremely high N incorporation efficiency in the In containing (GaIn)(NAs). The (GaIn)(NAs) samples investigated in this study have been examined using high resolution X-Ray diffraction, room temperature photoluminescence and atomic force microscope measurements as well as secondary ion mass spectrometry.

Determination of purine contents in different parts of pork and beef by high performance liquid chromatography.

PubMed

Rong, Shengzhong; Zou, Lina; Zhang, Yannan; Zhang, Guangteng; Li, Xiaoxia; Li, Miaojing; Yang, Fenghua; Li, Chunmei; He, Yingjuan; Guan, Hongjun; Guo, Yupeng; Wang, Dong; Cui, Xinyu; Ye, Hongting; Liu, Fenghai; Pan, Hongzhi; Yang, Yuexin

2015-03-01

Determination of adenine, hypoxanthine, guanine and xanthine in different parts of pork and beef using high performance liquid chromatography was described. Chromatographic separation was carried out on Waters Atlantis T3 column (4.6 mm × 250 mm × 5 μm) with column temperature at 30 °C. The mobile phase contained 99% 10.0 mmol/L ammonium formate solution at pH 3.6 and 1.0% methanol. Chromatography was achieved at a flow rate of 1.0 mL/min and detection wavelength at 254 nm. The results indicated that total purine amounts in pork rump and beef sirloin were higher than those in other parts (P<0.05). The principal purine bases were hypoxanthine and adenine, and hypoxanthine content was the most highest in all samples (P<0.05). As pork rump and beef sirloin contain considerable amounts of total purine and uricogenic purine base, we suggest that excess consumption of them be avoid, whereas pork loin chop and beef rib eye are more suitable for a low-purine diet. Copyright © 2014 Elsevier Ltd. All rights reserved.

Graphite intercalation compound with iodine as the major intercalant

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh; Kucera, Donald

1992-01-01

Halogenated CBr(sub x)I(sub y) (1 less than y/x less than 10) was made by exposing graphite materials with interplanar spacing in the 3.35 to 3.41 A range to either pure Br2 or an I2-Br2 mixture, and then to iodine vapor containing a small amount of Br2. The electrical resistivity of this product is from 3 to 6.5 times the pristine value. The presence of a small amount of isoprene rubber in the reaction significantly increased the iodine to bromine ratio in the product. In this reaction, rubber is known to generate HBr and to slowly remove bromine from the vapor. The halogenation generally caused a 22 to 25 percent weight increase. The halogens were found uniformly distributed in the product interior. However, although the surface contains very little iodine, it has high concentrations of bromine and oxygen. It is believed that the high concentrations of bromine and oxygen in this surface cause the halogenated fiber to be more resistant to fluorine attack during subsequent fluorination to fabricate graphite fluoride fibers.

Oil-water separation property of polymer-contained wastewater from polymer-flooding oilfields in Bohai Bay, China.

PubMed

Chen, Hua-xing; Tang, Hong-ming; Duan, Ming; Liu, Yi-gang; Liu, Min; Zhao, Feng

2015-01-01

In this study, the effects of gravitational settling time, temperature, speed and time of centrifugation, flocculant type and dosage, bubble size and gas amount were investigated. The results show that the simple increase in settling time and temperature is of no use for oil-water separation of the three wastewater samples. As far as oil-water separation efficiency is concerned, increasing centrifugal speed and centrifugal time is highly effective for L sample, and has a certain effect on J sample, but is not valid for S sample. The flocculants are highly effective for S and L samples, and the oil-water separation efficiency increases with an increase in the concentration of inorganic cationic flocculants. There exist critical reagent concentrations for the organic cationic and the nonionic flocculants, wherein a higher or lower concentration of flocculant would cause a decrease in the treatment efficiency. Flotation is an effective approach for oil-water separation of polymer-contained wastewater from the three oilfields. The oil-water separation efficiency can be enhanced by increasing floatation agent concentration, flotation time and gas amount, and by decreasing bubble size.

A Highly Sensitive Assay Using Synthetic Blood Containing Test Microbes for Evaluation of the Penetration Resistance of Protective Clothing Material under Applied Pressure.

PubMed

Shimasaki, Noriko; Hara, Masayuki; Kikuno, Ritsuko; Shinohara, Katsuaki

2016-01-01

To prevent nosocomial infections caused by even either Ebola virus or methicillin-resistant Staphylococcus aureus (MRSA), healthcare workers must wear the appropriate protective clothing which can inhibit contact transmission of these pathogens. Therefore, it is necessary to evaluate the performance of protective clothing for penetration resistance against infectious agents. In Japan, some standard methods were established to evaluate the penetration resistance of protective clothing fabric materials under applied pressure. However, these methods only roughly classified the penetration resistance of fabrics, and the detection sensitivity of the methods and the penetration amount with respect to the relationship between blood and the pathogen have not been studied in detail. Moreover, no standard method using bacteria for evaluation is known. Here, to evaluate penetration resistance of protective clothing materials under applied pressure, the detection sensitivity and the leak amount were investigated by using synthetic blood containing bacteriophage phi-X174 or S. aureus. And the volume of leaked synthetic blood and the amount of test microbe penetration were simultaneously quantified. Our results showed that the penetration detection sensitivity achieved using a test microbial culture was higher than that achieved using synthetic blood at invisible leak level pressures. This finding suggested that there is a potential risk of pathogen penetration even when visual leak of contaminated blood through the protective clothing was not observed. Moreover, at visible leak level pressures, it was found that the amount of test microbe penetration varied at least ten-fold among protective clothing materials classified into the same class of penetration resistance. Analysis of the penetration amount revealed a significant correlation between the volume of penetrated synthetic blood and the amount of test microbe penetration, indicating that the leaked volume of synthetic blood could be considered as a latent indicator for infection risk, that the amount of exposure to contaminated blood corresponds to the risk of infection. Our study helped us ascertain, with high sensitivity, the differences among fabric materials with respect to their protective performance, which may facilitate effective selection of protective clothing depending on the risk assessment.

A technique for estimating seed production of common moist soil plants

USGS Publications Warehouse

Laubhan, Murray K.

1992-01-01

Seeds of native herbaceous vegetation adapted to germination in hydric soils (i.e., moist-soil plants) provide waterfowl with nutritional resources including essential amino acids, vitamins, and minerals that occur only in small amounts or are absent in other foods. These elements are essential for waterfowl to successfully complete aspects of the annual cycle such as molt and reproduction. Moist-soil vegetation also has the advantages of consistent production of foods across years with varying water availability, low management costs, high tolerance to diverse environmental conditions, and low deterioration rates of seeds after flooding. The amount of seed produced differs among plant species and varies annually depending on environmental conditions and management practices. Further, many moist-soil impoundments contain diverse vegetation, and seed production by a particular plant species usually is not uniform across an entire unit. Consequently, estimating total seed production within an impoundment is extremely difficult. The chemical composition of seeds also varies among plant species. For example, beggartick seeds contain high amounts of protein but only an intermediate amount of minerals. In contrast, barnyardgrass is a good source of minerals but is low in protein. Because of these differences, it is necessary to know the amount of seed produced by each plant species if the nutritional resources provided in an impoundment are to be estimated. The following technique for estimating seed production takes into account the variation resulting from different environmental conditions and management practices as well as differences in the amount of seed produced by various plant species. The technique was developed to provide resource managers with the ability to make quick and reliable estimates of seed production. Although on-site information must be collected, the amount of field time required is small (i.e., about 1 min per sample); sampling normally is accomplished on an area within a few days. Estimates of seed production derived with this technique are used, in combination with other available information, to determine the potential number of waterfowl use-days available and to evaluate the effects of various management strategies on a particular site.

Evaluation of octyl p-methoxycinnamate included in liposomes and cyclodextrins in anti-solar preparations: preparations, characterizations and in vitro penetration studies

PubMed Central

de Souza de Bustamante Monteiro, Mariana Sato; Ozzetti, Rafael Antonio; Vergnanini, André Luiz; de Brito-Gitirana, Lycia; Volpato, Nadia Maria; de Freitas, Zaida Maria Faria; Ricci-Júnior, Eduardo; dos Santos, Elisabete Pereira

2012-01-01

Purpose Awareness of the harmful effects of ultraviolet radiation has led to the increasing use of sunscreens, thus, the development of safe and effective antisolar preparations is important. The inclusion of sunscreen molecules in different release systems, like liposomes (lipo) and cyclodextrins (CD) is therefore required. Methods The in vivo sun protection factor (SPF), water resistance, and in vitro transdermal penetration test of octyl p-methoxycinnamate (OMC) in different dispersions, such as OMC encapsulated in liposomes (lipo/OMC), OMC encapsulated in β-cyclodextrins (β-CD/OMC), OMC encapsulated in both release systems (lipo/OMC and β-CD/OMC), and an OMC-free formulation were determined. Results Although the formulation containing only the lipo/OMC system revealed high value of in vivo SPF (11.0 ± 1.3) and water resistance (SPF = 10.3 ± 2.2), the formulation containing both release systems (lipo/OMC + β-cyclodextrin/OMC) showed the best result in the in vivo SPF test (11.6 ± 1.6). In the penetration test, the formulation containing the lipo/OMC system had better performance, since a high amount of OMC in the epidermis (18.04 ± 1.17 μg) and a low amount of OMC in the dermis (9.4 ± 2.36 μg) were observed. These results suggest that liposomes interact with the cells of the stratum corneum, promoting retention of OMC in this layer. Conclusion According to our study, the lipo/OMC system is the most advantageous release system, due to its ability to both increase the amount of OMC in the epidermis and decrease the risk of percutaneous absorption. PMID:22787399

Relative Composition of Fibrous Connective and Fatty/Glandular Tissue in Connective Tissue Grafts Depends on the Harvesting Technique but not the Donor Site of the Hard Palate.

PubMed

Bertl, Kristina; Pifl, Markus; Hirtler, Lena; Rendl, Barbara; Nürnberger, Sylvia; Stavropoulos, Andreas; Ulm, Christian

2015-12-01

Whether the composition of palatal connective tissue grafts (CTGs) varies depending on donor site or harvesting technique in terms of relative amounts of fibrous connective tissue (CT) and fatty/glandular tissue (FGT) is currently unknown and is histologically assessed in the present study. In 10 fresh human cadavers, tissue samples were harvested in the anterior and posterior palate and in areas close to (marginal) and distant from (apical) the mucosal margin. Mucosal thickness, lamina propria thickness (defined as the extent of subepithelial portion of the biopsy containing ≤25% or ≤50% FGT), and proportions of CT and FGT were semi-automatically estimated for the entire mucosa and for CTGs virtually harvested by split-flap (SF) preparation minimum 1 mm deep or after deepithelialization (DE). Palatal mucosal thickness, ranging from 2.35 to 6.89 mm, and histologic composition showed high interindividual variability. Lamina propria thickness (P >0.21) and proportions of CT (P = 0.48) and FGT (P = 0.15) did not differ significantly among the donor sites (anterior, posterior, marginal, apical). However, thicker palatal tissue was associated with higher FGT content (P <0.01) and thinner lamina propria (P ≤0.03). Independent of the donor site, DE-harvested CTG contained a significantly higher proportion of CT and a lower proportion of FGT than an SF-harvested CTG (P <0.04). Despite high interindividual variability in terms of relative tissue composition in the hard palate, DE-harvested CTG contains much larger amounts of CT and much lower amounts of FGT than SF-harvested CTG, irrespective of the harvesting site.

Pharmacokinetics of [ 14C]-Benzo[a]pyrene (BaP) in humans: Impact of Co-Administration of smoked salmon and BaP dietary restriction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hummel, Jessica M.; Madeen, Erin P.; Siddens, Lisbeth K.

Benzo[a]pyrene (BaP), a polycyclic aromatic hydrocarbon (PAH), is a known human carcinogen. In non-smoking adults greater than 95% of BaP exposure is through diet. The carcinogenicity of BaP is utilized by the U.S. EPA to assess relative potency of complex PAH mixtures. PAH relative potency factors (RPFs, BaP=1) are determined from high dose animal data. Here we employed accelerator mass spectrometry (AMS) to determine pharmacokinetics of [ 14C]-BaP in humans following dosing with 46 ng (an order of magnitude lower than human dietary daily exposure and million-fold lower than animal cancer models). To assess the impact of co-administration of foodmore » with a complex PAH mixture, humans were dosed with 46 ng of [ 14C]-BaP with or without smoked salmon. Subjects were asked to avoid high BaP-containing diets and a 3-day dietary questionnaire given to assess dietary exposure prior to dosing and three days post-dosing with [ 14C]-BaP. Co-administration of smoked salmon, containing a complex mixture of PAHs with an RPF of 460 ng BaP eq, reduced and delayed absorption. Administration of canned commercial salmon, containing very low amounts of PAHs, showed the impacts on pharmacokinetics were not due to high amounts of PAHs but rather a food matrix effect.« less

Pharmacokinetics of [ 14C]-Benzo[a]pyrene (BaP) in humans: Impact of Co-Administration of smoked salmon and BaP dietary restriction

DOE PAGES

Hummel, Jessica M.; Madeen, Erin P.; Siddens, Lisbeth K.; ...

2018-03-01

Benzo[a]pyrene (BaP), a polycyclic aromatic hydrocarbon (PAH), is a known human carcinogen. In non-smoking adults greater than 95% of BaP exposure is through diet. The carcinogenicity of BaP is utilized by the U.S. EPA to assess relative potency of complex PAH mixtures. PAH relative potency factors (RPFs, BaP=1) are determined from high dose animal data. Here we employed accelerator mass spectrometry (AMS) to determine pharmacokinetics of [ 14C]-BaP in humans following dosing with 46 ng (an order of magnitude lower than human dietary daily exposure and million-fold lower than animal cancer models). To assess the impact of co-administration of foodmore » with a complex PAH mixture, humans were dosed with 46 ng of [ 14C]-BaP with or without smoked salmon. Subjects were asked to avoid high BaP-containing diets and a 3-day dietary questionnaire given to assess dietary exposure prior to dosing and three days post-dosing with [ 14C]-BaP. Co-administration of smoked salmon, containing a complex mixture of PAHs with an RPF of 460 ng BaP eq, reduced and delayed absorption. Administration of canned commercial salmon, containing very low amounts of PAHs, showed the impacts on pharmacokinetics were not due to high amounts of PAHs but rather a food matrix effect.« less

Stevia rebaudiana Bert. leaf extracts as a multifunctional source of natural antioxidants.

PubMed

Gaweł-Bęben, Katarzyna; Bujak, Tomasz; Nizioł-Łukaszewska, Zofia; Antosiewicz, Beata; Jakubczyk, Anna; Karaś, Monika; Rybczyńska, Kamila

2015-03-27

The aim of the presented study was to characterize the content and biological activity of extracts prepared from dried Stevia rebaudiana leaves with potential application in the food or cosmetic industry. Aqueous (A), ethanolic (E) and glycol-aqueous (GA) extracts were analyzed for the content of polyphenols and proteins, showing that the highest amount of phenols (15.50 mg/g) and flavonoids (3.85 mg/g) contained GA. All extracts contained significant amount of protein (69.40-374.67 mg/g). Between analyzed stevia extracts (HPLC) GA contained the highest amount of polyphenols, especially ferulic (5.50 mg/g) and rozmaric (4.95 mg/g) acids derivates. The highest antiradical activity against DPPH• and ABTS•+ was noted for GA and E (IC50 = 0.38 and 0.71 µg flavonoids/mL). The highest ability to chelate Fe2+ was observed for E (IC50 = 2.08 µg flavonoids/mL). Stevia extracts were also analyzed for their cytotoxicity and fibroblast irritation potential in vitro. E and GA were the most cytotoxic and irritating, probably due to the high content of biologically active phytochemicals. On the other hand, a extract was the most tolerable by the cells. To summarize, the presented study evaluated the potential application of A, E and GA stevia extracts as natural source of antioxidants in the food and cosmetic industry.

Simplified method for preparation of concentrated exoproteins produced by Staphylococcus aureus grown on surface of cellophane bag containing liquid medium.

PubMed

Ikigai, H; Seki, K; Nishihara, S; Masuda, S

1988-01-01

A simplified method for preparation of concentrated exoproteins including protein A and alpha-toxin produced by Staphylococcus aureus was successfully devised. The concentrated proteins were obtained by cultivating S. aureus organisms on the surface of a liquid medium-containing cellophane bag enclosed in a sterilized glass flask. With the same amount of medium, the total amount of proteins obtained by the method presented here was identical with that obtained by conventional liquid culture. The concentration of proteins obtained by the method, however, was high enough to observe their distinct bands stained on polyacrylamide gel electrophoresis. This method was considered quite useful not only for large-scale cultivation for the purification of staphylococcal proteins but also for small-scale study using the proteins. The precise description of the method was presented and its possible usefulness was discussed.

Evaluation and auger analysis of a zinc-dialkyl-dithiophosphate antiwear additive in several diester lubricants

NASA Technical Reports Server (NTRS)

Brainard, W. A.; Ferrante, J.

1979-01-01

The wear of pure iron in sliding contact with hardened M-2 tool steel was measured for a series of synthetic diester fluids, both with and without a zinc dialkyl dithiophosphate (ZDP) antiwear additive, as test lubricants. Selected wear scars were analyzed by an Auger emission spectroscopy (AES) depth profiling technique in order to assess the surface film elemental composition. The ZDP was an effective antiwear additive for all the diesters except dibutyl oxalate and dibutyl sebacate. The high wear measured for the additive-containing oxalate was related to corrosion; the higher wear measured for the additive-containing sebacate was due to an oxygen interaction. The AES of dibutyl sebacate surfaces run in dry air and in dry nitrogen showed large differences only in the amount of oxygen present. The AES of worn surfaces where the additive was effective showed no zinc, only a little phosphorus, and large amounts of sulfur.

Delivery of kinesin spindle protein targeting siRNA in solid lipid nanoparticles to cellular models of tumor vasculature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ying, Bo; Campbell, Robert B., E-mail: robert.campbell@mcphs.edu

2014-04-04

Highlights: • siRNA-lipid nanoparticles are solid particles not lipid bilayers with aqueous core. • High, but not low, PEG content can prevent nanoparticle encapsulation of siRNA. • PEG reduces cellular toxicity of cationic nanoparticles in vitro. • PEG reduces zeta potential while improving gene silencing of siRNA nanoparticles. • Kinesin spindle protein can be an effective target for tumor vascular targeting. - Abstract: The ideal siRNA delivery system should selectively deliver the construct to the target cell, avoid enzymatic degradation, and evade uptake by phagocytes. In the present study, we evaluated the importance of polyethylene glycol (PEG) on lipid-based carriermore » systems for encapsulating, and delivering, siRNA to tumor vessels using cellular models. Lipid nanoparticles containing different percentage of PEG were evaluated based on their physical chemical properties, density compared to water, siRNA encapsulation, toxicity, targeting efficiency and gene silencing in vitro. siRNA can be efficiently loaded into lipid nanoparticles (LNPs) when DOTAP is included in the formulation mixture. However, the total amount encapsulated decreased with increase in PEG content. In the presence of siRNA, the final formulations contained a mixed population of particles based on density. The major population which contains the majority of siRNA exhibited a density of 4% glucose, and the minor fraction associated with a decreased amount of siRNA had a density less than PBS. The inclusion of 10 mol% PEG resulted in a greater amount of siRNA associated with the minor fraction. Finally, when kinesin spindle protein (KSP) siRNA was encapsulated in lipid nanoparticles containing a modest amount of PEG, the proliferation of endothelial cells was inhibited due to the efficient knock down of KSP mRNA. The presence of siRNA resulted in the formation of solid lipid nanoparticles when prepared using the thin film and hydration method. LNPs with a relatively modest amount of PEG can sufficiently encapsulate siRNA, improve cellular uptake and the efficiency of gene silencing.« less

Distortion of three-unit implant frameworks during casting, soldering, and simulated porcelain firings.

PubMed

Zervas, P J; Papazoglou, E; Beck, F M; Carr, A B

1999-09-01

The aim of this study was to assess distortion inherent in casting, soldering, and simulated porcelain firings of screw-retained, implant-supported three-unit fixed partial dentures (FPDs). Ten wax patterns were fabricated on a die-stone cast containing two implants, 20 mm apart from center to center. Five specimens were cast in a high-palladium alloy, exposed to simulated porcelain firings, sectioned, and then soldered with low-fusing solder. Five specimens were cast, sectioned, soldered with high-fusing solder, and then exposed to simulated porcelain firings. For each specimen, two horizontal and six vertical distances between appropriately scribed reference points were measured with a traveling microscope. Comparisons were made among the various measurements taken after wax-pattern fabrication, casting, high- and low-fusing soldering, and each porcelain firing. Data were analyzed using a repeated-measures factorial ANOVA (alpha = 0.05). Significant difference was detected in the amount of horizontal distortion during casting (53 +/- 24 microns) and high-fusing soldering (-49 +/- 50 microns), as well as in the amount of horizontal distortion during high-fusing soldering (-49 +/- 50 microns) and low-fusing soldering (17 +/- 26 microns). However, no clinically significant difference was found in the amount of horizontal distortion during casting, low-fusing, and high-fusing soldering. The greatest amount of distortion during the simulated porcelain firings took place during the oxidizing cycle. Soldering did not improve the casting misfit of a three-unit implant-retained FPD model. Metal-ceramic implant frameworks should be oxidized before intraoral fit evaluation.

Very high-pressure orogenic garnet peridotites

PubMed Central

Liou, J. G.; Zhang, R. Y.; Ernst, W. G.

2007-01-01

Mantle-derived garnet peridotites are a minor component in many very high-pressure metamorphic terranes that formed during continental subduction and collision. Some of these mantle rocks contain trace amounts of zircon and micrometer-sized inclusions. The constituent minerals exhibit pre- and postsubduction microstructures, including polymorphic transformation and mineral exsolution. Experimental, mineralogical, petrochemical, and geochronological characterizations using novel techniques with high spatial, temporal, and energy resolutions are resulting in unexpected discoveries of new phases, providing better constraints on deep mantle processes. PMID:17519341

A multiresolution approach to iterative reconstruction algorithms in X-ray computed tomography.

PubMed

De Witte, Yoni; Vlassenbroeck, Jelle; Van Hoorebeke, Luc

2010-09-01

In computed tomography, the application of iterative reconstruction methods in practical situations is impeded by their high computational demands. Especially in high resolution X-ray computed tomography, where reconstruction volumes contain a high number of volume elements (several giga voxels), this computational burden prevents their actual breakthrough. Besides the large amount of calculations, iterative algorithms require the entire volume to be kept in memory during reconstruction, which quickly becomes cumbersome for large data sets. To overcome this obstacle, we present a novel multiresolution reconstruction, which greatly reduces the required amount of memory without significantly affecting the reconstructed image quality. It is shown that, combined with an efficient implementation on a graphical processing unit, the multiresolution approach enables the application of iterative algorithms in the reconstruction of large volumes at an acceptable speed using only limited resources.

[Studies on high temperature oxidation of noble metal alloys for dental use. (III) On high temperature oxidation resistance of noble metal alloys by adding small amounts of alloying elements. (author's transl)].

PubMed

Ohno, H

1976-11-01

The previous report pointed out the undesirable effects of high temperature oxidation on the casting. The influence of small separate additions of Zn, Mg, Si, Be and Al on the high temperature oxidation of the noble metal alloys was examined. These alloying elements were chosen because their oxide have a high electrical resistivity and they have much higher affinity for oxygen than Cu. The casting were oxidized at 700 degrees C for 1 hour in air. The results obtained were as follows: 1. The Cu oxides are not observed on the as-cast surface of noble metal alloys containing small amounts of Zn, Mg, Si, Be, and Al. The castings have gold- or silver-colored surface. 2. After heating of the unpolished and polished castings, the additions of Si, Be and Al are effective in preventing oxidation of Cu in the 18 carats gold alloys. Especially the golden surface is obtained by adding Be and Al. But there is no oxidation-resistance on the polished castings in the alloys containing Zn and Mg. 3. The zinc oxide film formed on the as-cast specimen is effective in preventing of oxidation Cu in 18 carats gold alloys. 4. It seems that the addition of Al is most available in dental application.

Method of forming a relatively stable slip of silicon metal particles and yttrium containing particles

DOEpatents

Dickie, Ray A.; Mangels, John A.

1984-01-01

The method concerns forming a relatively stable slip of silicon metal particles and yttrium containing particles. In one embodiment, a casting slip of silicon metal particles is formed in water. Particles of a yttrium containing sintering aid are added to the casting slip. The yttrium containing sintering aid is a compound which has at least some solubility in water to form Y.sup.+3 ions which have a high potential for totally flocculating the silicon metal particles into a semiporous solid. A small amount of a fluoride salt is added to the casting slip which contains the yttrium containing sintering aid. The fluoride salt is one which will produce fluoride anions when dissolved in water. The small amount of the fluoride anions produced are effective to suppress the flocculation of the silicon metal particles by the Y.sup.+3 ions so that all particles remain in suspension in the casting slip and the casting slip has both an increased shelf life and can be used to cast articles having a relatively thick cross-section. The pH of the casting slip is maintained in a range from 7.5 to 9. Preferably, the fluoride salt used is one which is based on a monovalent cation such as sodium or ammonia. The steps of adding the yttrium containing sintering aid and the fluoride salt may be interchanged if desired, and the salt may be added to a solution containing the sintering aid prior to addition of the silicon metal particles.

A Systematic Review of High-Oleic Vegetable Oil Substitutions for Other Fats and Oils on Cardiovascular Disease Risk Factors: Implications for Novel High-Oleic Soybean Oils12

PubMed Central

Huth, Peter J; Fulgoni, Victor L; Larson, Brian T

2015-01-01

High–oleic acid soybean oil (H-OSBO) is a trait-enhanced vegetable oil containing >70% oleic acid. Developed as an alternative for trans-FA (TFA)-containing vegetable oils, H-OSBO is predicted to replace large amounts of soybean oil in the US diet. However, there is little evidence concerning the effects of H-OSBO on coronary heart disease (CHD)6 risk factors and CHD risk. We examined and quantified the effects of substituting high-oleic acid (HO) oils for fats and oils rich in saturated FAs (SFAs), TFAs, or n–6 (ω-6) polyunsaturated FAs (PUFAs) on blood lipids in controlled clinical trials. Searches of online databases through June 2014 were used to select studies that defined subject characteristics; described control and intervention diets; substituted HO oils compositionally similar to H-OSBO (i.e., ≥70% oleic acid) for equivalent amounts of oils high in SFAs, TFAs, or n–6 PUFAs for ≥3 wk; and reported changes in blood lipids. Studies that replaced saturated fats or oils with HO oils showed significant reductions in total cholesterol (TC), LDL cholesterol, and apolipoprotein B (apoB) (P < 0.05; mean percentage of change: −8.0%, −10.9%, −7.9%, respectively), whereas most showed no changes in HDL cholesterol, triglycerides (TGs), the ratio of TC to HDL cholesterol (TC:HDL cholesterol), and apolipoprotein A-1 (apoA-1). Replacing TFA-containing oil sources with HO oils showed significant reductions in TC, LDL cholesterol, apoB, TGs, TC:HDL cholesterol and increased HDL cholesterol and apoA-1 (mean percentage of change: −5.7%, −9.2%, −7.3%, −11.7%, −12.1%, 5.6%, 3.7%, respectively; P < 0.05). In most studies that replaced oils high in n–6 PUFAs with equivalent amounts of HO oils, TC, LDL cholesterol, TGs, HDL cholesterol, apoA-1, and TC:HDL cholesterol did not change. These findings suggest that replacing fats and oils high in SFAs or TFAs with either H-OSBO or oils high in n–6 PUFAs would have favorable and comparable effects on plasma lipid risk factors and overall CHD risk. PMID:26567193

Semimicrodetermination of tantalum with selenous acid

USGS Publications Warehouse

Grimaldi, F.S.; Schnepfe, M.M.

1958-01-01

Tantalum is separated and determined gravimetrically by precipitation with selenous acid from a highly acidic solution containing oxalic and tartaric acids. The method is selective for the determination of up to 30 mg. of tantalum pentoxide, and tolerates relatively large amounts of scandium, yttrium, cerium, titanium, zirconium, thorium, vanadium, niobium, molybdenum, tungsten, uranium, iron, aluminum, gallium, tin, lead, antimony, and bismuth. The separation of tantalum from niobium and titanium is not strictly quantitative, and correction is made colorimetrically for the small amounts of niobium and titanium co-precipitating with the tantalum. The method was applied to the determination of tantalum in tantaloniobate ores.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weaver, G.T.; Kanna, P.K.; Beese, F.

A shallow slightly acid Terra fusca (Rendolls) soil derived from triassic limestone contains substantial amounts of sulfate. Under high sulfate input, low pH and high salt input this soil can further retain sulfate. Soil chemical data indicate that this soil contains exchangeable Al and H. This finding and the analysis of the equilibrium soil solutions from batch and percolation studies indicate that the retention of sulfate can be described by an equilibrium solid/solution phase of the type Al(OH)SO4 (aluminum hydroxy sulfate). Under similar experimental conditions of solution composition and concentration, Freundlich type adsorption/desorption isotherms and the general solute transport equationmore » can describe the retention and transport of sulfate in this soil.« less

Contribution of mesopores in MgO-templated mesoporous carbons to capacitance in non-aqueous electrolytes

NASA Astrophysics Data System (ADS)

Kado, Yuya; Soneda, Yasushi; Yoshizawa, Noriko

2015-02-01

MgO-templated mesoporous carbons were fabricated by annealing trimagnesium dicitrate nonahydrate at various temperatures from 700 to 1000 °C with subsequent acid leaching of MgO. The obtained carbons contained a large amount of mesopores. Performances of electric double-layer capacitors using these carbons were examined for propylene carbonate electrolyte containing 1 M tetraethylammonium tetrafluoroborate. The mesoporous carbons synthesized at higher temperatures showed better rate capabilities. AC impedance measurements indicated that high-temperature annealing of the carbon precursors and the presence of mesopores were important for high rate performance. In addition, the contribution of mesopores to capacitance was more significant at higher current densities of 30 A g-1.

Cesium titanium silicate and method of making

DOEpatents

Balmer, Mari L.

1997-01-01

The invention is the new material, a ternary compound of cesium, silica, and titania, together with a method of making the ternary compound, cesium titanium silicate pollucite. More specifically, the invention is Cs.sub.2 Ti.sub.2 Si.sub.4 O.sub.13 pollucite which is a new crystalline phase representing a novel class of Ti-containing zeolites. Compositions contain relatively high Cs.sub.2 O and TiO.sub.2 loadings and are durable glass and ceramic materials. The amount of TiO.sub.2 and Cs.sub.2 that can be incorporated into these glasses and crystalline ceramics far exceeds the limits set for the borosilicate high level waste glass.

Cesium titanium silicate and method of making

DOEpatents

Balmer, M.L.

1997-01-07

The invention is the new material, a ternary compound of cesium, silica, and titania, together with a method of making the ternary compound, cesium titanium silicate pollucite. More specifically, the invention is Cs{sub 2}Ti{sub 2}Si{sub 4}O{sub 13} pollucite which is a new crystalline phase representing a novel class of Ti-containing zeolites. Compositions contain relatively high Cs{sub 2}O and TiO{sub 2} loadings and are durable glass and ceramic materials. The amount of TiO{sub 2} and Cs{sub 2} that can be incorporated into these glasses and crystalline ceramics far exceeds the limits set for the borosilicate high level waste glass. 10 figs.

Preliminary Assessment/Site Inspection Health and Safety Plan, Granite Mountain RRS, Alaska

DTIC Science & Technology

1994-08-01

pain. apple cores. banana peels , lettuce, fish and game carcasses, etc.). Sealed beafproof contuiner: a container sealed to prevent the escap...acrylates, and alcohols . These substances are slightly to highly volatile and are moderately to highly flammable. Primary routes of entry into the body...with copious amounts of water for at least 15 minutes. Get emergency medical assistance. 3 Skin Contact: Flush thoroughly for at least 1S minutes& Wash

Migration of fluorochemical paper additives from food-contact paper into foods and food simulants.

PubMed

Begley, T H; Hsu, W; Noonan, G; Diachenko, G

2008-03-01

Fluorochemical-treated paper was tested to determine the amount of migration that occurs into foods and food-simulating liquids and the characteristics of the migration. Migration characteristics of fluorochemicals from paper were examined in Miglyol, butter, water, vinegar, water-ethanol solutions, emulsions and pure oil containing small amounts of emulsifiers. Additionally, microwave popcorn and chocolate spread were used to investigate migration. Results indicate that fluorochemicals paper additives do migrate to food during actual package use. For example, we found that microwave popcorn contained 3.2 fluorochemical mg kg(-1) popcorn after popping and butter contained 0.1 mg kg(-1) after 40 days at 4 degrees C. Tests also indicate that common food-simulating liquids for migration testing and package material evaluation might not provide an accurate indication of the amount of fluorochemical that actually migrates to food. Tests show that oil containing small amounts of an emulsifier can significantly enhance migration of a fluorochemical from paper.

Evaluation of spatial, radiometric and spectral thematic mapper performance for coastal studies

NASA Technical Reports Server (NTRS)

Klemas, V.

1983-01-01

Radiative transfer theory was used to model upwelling radiance for an orbiting sensor viewing an estuarine environment. Radiance was calculated in Tm bands 3,4, and 5 and MSS bands 4 and 5 for an optically shallow estuary of either clear or turbid water, and of three bottom types: vegetation, sand, or mud. A portion of a TM image of Chesapeake Bay was enhanced to obtain a quick look at what submerged features could be detected. The enhancements were compared with low altitude color aerial photography. The TM bands 1,2, and 3 were found to contain water and submerged features information. Band 1 contained a significant amount of noise and low contrast. Band 2 appeared to contain the most amount of bottom information. Band 3, while having the least amount of noise and best constrast, contained a lesser amount of bottom information because of increase water absorption. Several water signatures were identified which correlated with submerged vegetation shown in the aerial photography.

Geological and geochemical studies in the Wadi Bidah District, Kingdom of Saudi Arabia

USGS Publications Warehouse

Smith, C.W.; Waters, B.C.; Naqvi, M.; Worl, R.G.; Helaby, A.M.; Flanigan, V.J.; Sadek, H.S.; Samater, R.M.

1983-01-01

Geological and geochemical followup studies of airborne electromagnetic anomalies in the Wadi Bidah district, southwestern Saudi Arabia, did not reveal metals of economic grade. Investigation of an anomaly enclosing the Rabathan ancient mine disclosed tightly folded and sheared Proterozoic tuffaceous rocks interlayered mostly with chert, dolomite, carbonaceous rocks, and volcanic wacke including cherty iron-manganese formations slightly anomalous in copper and zinc. Three drill holes placed to test anomalies within these formations yielded negative results. Studies of a long, narrow anomaly north of the Rabathan area indicated a similar geological environment. This northern area also contains limited zones that are highly anomalous in copper and zinc and extensive zones that are slightly anomalous in those metals. Drilling was not undertaken in this area. The Bilajimah airborne electromagnetic anomaly west of Wadi Bidah coincides with a broad synclinorium of layered felsic turfs and gossans. Geochemical studies indicated slightly anomalous copper, zinc, and silver values in gossans within the anomaly area. Two drill holes intersected carbonaceous rock that contained approximately 15 percent pyrrhotite and traces of sphalerite and chalcopyrite. Two geophysically anomalous areas west of Wadi Bidah surround ancient mines at Mahawiyah and Khayal al Masna'ah. Results of geochemical sampling at these workings were positive. An airborne electromagnetic anomaly located in the Assifar area in the southwestern corner of the Wadi Bidah district is underlain principally by metasedimentary rocks that include large linear zones of cherty iron-manganese formation and a few gossans .containing secondary base metal minerals. Detailed mapping and sampling of the Mulhal ancient mine, located west of Wadi Bidah, revealed two types of polymetallic gossans : (1) stratiform deposits interlayered with ignimbrites and mafic volcanic rocks and (2) barite-bearing gossanous material in shear zones that grade into hydrothermally altered shear zones and extend beyond the mine area. The gossans and gossanous shear zones contain anomalous amounts of gold, silver, lead, copper, zinc, barium, and selenium. Two gossans west of Wadi Bidah were mapped and sampled in detail; both gossans are interlayered, with siliceous volcanic rocks. Although the gossan at Jabal Mohr covers a large area, it contains low amounts of precious and base metals. The gossan at Mulhal No. 2 contains moderate to high amounts of gold, silver, copper, lead, and zinc.

Dietary fructose but not starch is responsible for hyperlipidemia associated with copper deficiency in rats: effect of high-fat diet.

PubMed

Fields, M; Lewis, C G

1999-02-01

To test the hypothesis that copper deficiency in rats may be hyperlipidemic only when the diets consumed contain nutrients which contribute to blood lipids such as fructose and high fat. Weanling male Sprague Dawley rats were fed diets which contained either starch or fructose as their sole carbohydrate source. The diets were either inadequate (0.6 microg Cu/g) or adequate (6.0 microg Cu/g) in copper and contained either high (300 g/kg) or low (60 g/kg) fat. At the end of the 4th week the rats were killed. Livers were analyzed for copper content. Plasma was analyzed for cholesterol and triglyceride concentrations. High-fat diet did not increase blood lipids in rats fed a copper-deficient diet containing starch. In contrast, the combination of high-fat diet with fructose increased blood triglycerides and fructose with copper deficiency resulted in a significant increases in blood cholesterol. Hyperlipidemia of copper deficiency in rats is dependent on synergistic effects between dietary fructose and copper deficiency and fructose and amount of dietary fat. Hyperlipidemia does not develop if starch is the main source of dietary carbohydrate in a copper-deficient diet even if a high-fat diet is fed.

The origin, type and hydrocarbon generation potential of organic matter in a marine-continental transitional facies shale succession (Qaidam Basin, China).

PubMed

Wang, Guo-Cang; Sun, Min-Zhuo; Gao, Shu-Fang; Tang, Li

2018-04-26

This organic-rich shale was analyzed to determine the type, origin, maturity and depositional environment of the organic matter and to evaluate the hydrocarbon generation potential of the shale. This study is based on geochemical (total carbon content, Rock-Eval pyrolysis and the molecular composition of hydrocarbons) and whole-rock petrographic (maceral composition) analyses. The petrographic analyses show that the shale penetrated by the Chaiye 2 well contains large amounts of vitrinite and sapropelinite and that the organic matter within these rocks is type III and highly mature. The geochemical analyses show that these rocks are characterized by high total organic carbon contents and that the organic matter is derived from a mix of terrestrial and marine sources and highly mature. These geochemical characteristics are consistent with the results of the petrographic analyses. The large amounts of organic matter in the Carboniferous shale succession penetrated by the Chaiye 2 well may be due to good preservation under hypersaline lacustrine and anoxic marine conditions. Consequently, the studied shale possesses very good hydrocarbon generation potential because of the presence of large amounts of highly mature type III organic matter.

High pre-eruptive water contents preserved in lunar melt inclusions.

PubMed

Hauri, Erik H; Weinreich, Thomas; Saal, Alberto E; Rutherford, Malcolm C; Van Orman, James A

2011-07-08

The Moon has long been thought to be highly depleted in volatiles such as water, and indeed published direct measurements of water in lunar volcanic glasses have never exceeded 50 parts per million (ppm). Here, we report in situ measurements of water in lunar melt inclusions; these samples of primitive lunar magma, by virtue of being trapped within olivine crystals before volcanic eruption, did not experience posteruptive degassing. The lunar melt inclusions contain 615 to 1410 ppm water and high correlated amounts of fluorine (50 to 78 ppm), sulfur (612 to 877 ppm), and chlorine (1.5 to 3.0 ppm). These volatile contents are very similar to primitive terrestrial mid-ocean ridge basalts and indicate that some parts of the lunar interior contain as much water as Earth's upper mantle.

Structures and Fragmentation Mechanisms of the Ions of Ethanol by Triple Quadrupole Mass Spectrometry.

DTIC Science & Technology

1982-07-15

structural information contained in deuterated sp ies is readily obtainable. Eth 1 ions ty stdied tnc) Vde (CH3CHOH?’., [CH CHOHJ. (CH2COH]r-% [CH 2COF...high and low energy systems involves electronic 18 and vibrational 19 excitation respectively, the amount of energy thus deposited must be approximately

Gold (III) Chloride-Catalyzed 6-endo-trig Oxa-Michael Addition Reactions for Diastereoselective Synthesis of Fused Tetrahydropyranones

PubMed Central

Ciesielski, Jennifer; Lebœuf, David; Stern, Harry A.

2013-01-01

Alkynones were treated with boron trifluoride diethyl etherate to generate β-iodoallenolates, which underwent intramolecular aldol reactions to produce cycloalkenyl alcohols. Diastereoselective oxa-Michael ring closure could then be induced by treatment with a catalytic amount of gold(III) chloride, affording highly functionalized tetrahydropyran-containing ring systems. PMID:24032002

10 CFR 26.168 - Blind performance testing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... analyte and must be certified by immunoassay and confirmatory testing; (2) Drug positive. These samples must contain a measurable amount of the target drug or analyte in concentrations ranging between 150... performance test sample must contain a measurable amount of the target drug or analyte in concentrations...

10 CFR 26.168 - Blind performance testing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... analyte and must be certified by immunoassay and confirmatory testing; (2) Drug positive. These samples must contain a measurable amount of the target drug or analyte in concentrations ranging between 150... performance test sample must contain a measurable amount of the target drug or analyte in concentrations...

10 CFR 26.168 - Blind performance testing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... analyte and must be certified by immunoassay and confirmatory testing; (2) Drug positive. These samples must contain a measurable amount of the target drug or analyte in concentrations ranging between 150... performance test sample must contain a measurable amount of the target drug or analyte in concentrations...

10 CFR 26.168 - Blind performance testing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... analyte and must be certified by immunoassay and confirmatory testing; (2) Drug positive. These samples must contain a measurable amount of the target drug or analyte in concentrations ranging between 150... performance test sample must contain a measurable amount of the target drug or analyte in concentrations...

10 CFR 26.168 - Blind performance testing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... analyte and must be certified by immunoassay and confirmatory testing; (2) Drug positive. These samples must contain a measurable amount of the target drug or analyte in concentrations ranging between 150... performance test sample must contain a measurable amount of the target drug or analyte in concentrations...

Process and system for removing sulfur from sulfur-containing gaseous streams

DOEpatents

Basu, Arunabha; Meyer, Howard S.; Lynn, Scott; Leppin, Dennis; Wangerow, James R.

2012-08-14

A multi-stage UCSRP process and system for removal of sulfur from a gaseous stream in which the gaseous stream, which contains a first amount of H.sub.2S, is provided to a first stage UCSRP reactor vessel operating in an excess SO.sub.2 mode at a first amount of SO.sub.2, producing an effluent gas having a reduced amount of SO.sub.2, and in which the effluent gas is provided to a second stage UCSRP reactor vessel operating in an excess H.sub.2S mode, producing a product gas having an amount of H.sub.2S less than said first amount of H.sub.2S.

Development of high temperature nickel-base alloys for jet engine turbine bucket applications

NASA Technical Reports Server (NTRS)

Quigg, R. J.; Scheirer, S. T.

1965-01-01

A program has been initiated to develop a material with superior properties at elevated temperatures for utilization in turbine blade applications. A nickel-base superalloy can provide the necessary high temperature strength by using the maximum capability of the three available strengthening mechanisms - intermetallic gamma prime precipitation (Ni3Al), solid solution strengthening with refractory and precious metals, and stable carbide formations through the addition of strong carbide forming elements. A stress rupture test at 2000 deg F and 15,000 psi was formulated to approximate the desired properties. By adding varying amounts of refractory metals (Mo, W and Ta) it was possible to statistically analyze the effects of each in a basic superalloy composition containing fixed amounts of Co, Cr, C, B, Sr, and Ni at three separate levels of AL and Ta. Metallographic analysis correlated with the mechanical properties of the alloys; those with few strengthening phases were weak and ductile and those with excessive amounts of intermetallic phases present in undesirable morphologies were brittle.

Protective effect of Spirulina platensis enriched in phenolic compounds against hepatotoxicity induced by CCl4.

PubMed

Kepekçi, Remziye Aysun; Polat, Sait; Çelik, Ahmet; Bayat, Nuray; Saygideger, Saadet Demirörs

2013-12-01

Phenolic compounds make up the major secondary metabolites with high pharmaceutical potential. Microalgae were reported to contain low amounts of phenolic compounds. The present study aimed to investigate the hepatoprotective potential of biomass of Spirulina platensis enriched in phenolic compounds. The protective effects of the biomass of S. platensis with low amounts of phenolics (SP1) and with high amounts of phenolics (SP2) against CCl4-induced acute hepatotoxicity were evaluated in rats. The increased levels of ALT, AST and MDA along with decreased activities of SOD and CAT were significantly (p<0.01) ameliorated by SP2. Histological examinations revealed that SP2 was more potent than SP1 in protecting the liver from toxic injury of CCl4 and preserving the hepatocyte ultrastructure. The lesions including necrosis, lymphocyte infiltration, ballooning degeneration and hepatocyte injury as irregular lamellar organisation, dilations in endoplasmic reticulums and the presence of great number of cytoplasmic vacuolization were healed by SP2. Copyright © 2013 Elsevier Ltd. All rights reserved.

Quantification of organic solvents in aquatic toys and swimming learning devices and evaluation of their influence on the smell properties of the corresponding products.

PubMed

Wiedmer, Christoph; Buettner, Andrea

2018-04-01

Based on the observation that the characteristic odour of inflatable aquatic toys for children is predominantly caused by residues of hazardous organic solvents, the concentrations of cyclohexanone, isophorone and phenol were determined in a selection of 20 products obtained from online suppliers located in Germany. Analytes were extracted with dichloromethane after the addition of non-labelled internal standards, and the volatile fraction was isolated using solvent-assisted flavour evaporation (SAFE). Extracts were then concentrated by Vigreux distillation and analysed by means of gas chromatography with mass spectrometric detection (GC-MS). Furthermore, each sample was evaluated regarding its specific olfactory properties by an expert sensory panel. While some samples did not contain significant amounts of solvents, cyclohexanone concentrations above the lower limit of quantification (LLOQ) were determined in nine samples with six samples containing high concentrations ranging from about 1 to 7 g/kg cyclohexanone. Isophorone concentrations above the LLOQ were observed in eight samples. Thereby, six products contained between 0.3 and 1.6 g/kg isophorone and the remaining two samples contained even about 5 g/kg isophorone, each. Likewise, phenol concentrations exceeded the LLOQ in 14 cases, with four samples containing elevated amounts ranging from about 140 to 280 mg/kg phenol.

Poultry products enriched with nutricines have beneficial effects on human health.

PubMed

Kralik, Gordana; Kralik, Zlata

2017-02-01

The paper presents nutritive value of broiler meat and table eggs, as these animal products are used for human nutrition on a daily basis. In the Republic of Croatia, average consumption of poultry meat amounts to 18.3 kg and to 160 eggs per capita.The most quality parts of broiler carcass are breasts and drumsticks with thighs. Breast muscles contain 21-23% protein, 1.90-1.97% fat, 75.28-76.01% water and 0.74-0.77% collagen. Thigh muscles contain 4.70-6.05% fat, 19.03-19.93% protein and 0.91-1.13% collagen. White meat contains more potassium and magnesium and less zinc and iron than dark meat. In 100 g of edible egg part there is 12.5-13.5 g protein, 10.7-11.6 g fat and 1.0-1.1 g minerals. Caloric valueof eggs is 167 Kcal. Eggs contain high amount of essential amino acids, especially leucine, isoleucine, lysine, arginine, valine and phenylalanine. Furthermore, eggs contain many vitamins, especially A, D, E, K and B-complex, as well as various macroelements and microelements. Eggs and meat enriched with one or more functional ingredients - nutricines (polyunsaturated fatty acids n-3), eicosapentaenoic acid, docosahexaenoic acid, selenium and lutein) meet the criteria of functional food because of their added value and benefits for human health. Copyright© by the Medical Assotiation of Zenica-Doboj Canton.

Estimates of Ethanol Exposure in Children from Food not Labeled as Alcohol-Containing

PubMed Central

Gorgus, Eva; Hittinger, Maike; Schrenk, Dieter

2016-01-01

Abstract Ethanol is widely used in herbal medicines, e.g., for children. Furthermore, alcohol is a constituent of fermented food such as bread or yogurt and “non-fermented” food such as fruit juices. At the same time, exposure to very low levels of ethanol in children is discussed as possibly having adverse effects on psychomotoric functions. Here, we have analyzed alcohol levels in different food products from the German market. It was found that orange, apple and grape juice contain substantial amounts of ethanol (up to 0.77 g/L). Furthermore, certain packed bakery products such as burger rolls or sweet milk rolls contained more than 1.2 g ethanol/100 g. We designed a scenario for average ethanol exposure by a 6-year-old child. Consumption data for the “categories” bananas, bread and bakery products and apple juice were derived from US and German surveys. An average daily exposure of 10.3 mg ethanol/kg body weight (b.w.) was estimated. If a high (acute) consumption level was assumed for one of the “categories,” exposure rose to 12.5–23.3 mg/kg b.w. This amount is almost 2-fold (average) or up to 4-fold (high) higher than the lowest exposure from herbal medicines (6 mg/kg b.w.) suggested to require warning hints for the use in children. PMID:27405361

Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants.

PubMed

Adrados, A; De Marco, I; Lopez-Urionabarrenechea, A; Caballero, B M; Laresgoiti, M F

2013-01-01

In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm(3) reactor, swept with 1 L min(-1) N(2), at 500°C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33-40 MJ kg(-1)). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO(2); their HHV is in the range of 18-46 MJ kg(-1). The amount of COCO(2) increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char. Copyright © 2012 Elsevier Ltd. All rights reserved.

Stabilization of red blood cells by the plasticizer, diethylhexylphthalate.

PubMed

Horowitz, B; Stryker, M H; Waldman, A A; Woods, K R; Gass, J D; Drago, J

1985-01-01

The red blood cells of blood stored in containers made of polyvinylchloride (PVC) film are osmotically more stable and lose on average about 1/3 less hemoglobin than when blood is stored in another plastic [poly-(ethylene-co-ethyl acrylate); EEA]. The stability of uniform volumes of stored red blood cells varies directly with PVC surface area, whereas changes in EEA surface area have comparatively little or no effect. PVC contains high concentrations of the plasticizer, diethylhexylphthalate (DEHP), known to migrate into blood and to have a high potential for toxicity. To determine if DEHP could be the red cell stabilizing agent in PVC, whole blood was stored in containers made from EEA into which was incorporated varying amounts of DEHP. Incorporation of DEHP into EEA significantly reduced erythrocyte osmotic fragility (p = 0.01). The degree of reduced fragility correlated with the level of DEHP in the cell phase implicating DEHP in PVC containers as the stabilizing agent for red cells.

Comparison between the Amount of Environmental Change and the Amount of Transcriptome Change

PubMed Central

Ogata, Norichika; Kozaki, Toshinori; Yokoyama, Takeshi; Hata, Tamako; Iwabuchi, Kikuo

2015-01-01

Cells must coordinate adjustments in genome expression to accommodate changes in their environment. We hypothesized that the amount of transcriptome change is proportional to the amount of environmental change. To capture the effects of environmental changes on the transcriptome, we compared transcriptome diversities (defined as the Shannon entropy of frequency distribution) of silkworm fat-body tissues cultured with several concentrations of phenobarbital. Although there was no proportional relationship, we did identify a drug concentration “tipping point” between 0.25 and 1.0 mM. Cells cultured in media containing lower drug concentrations than the tipping point showed uniformly high transcriptome diversities, while those cultured at higher drug concentrations than the tipping point showed uniformly low transcriptome diversities. The plasticity of transcriptome diversity was corroborated by cultivations of fat bodies in MGM-450 insect medium without phenobarbital and in 0.25 mM phenobarbital-supplemented MGM-450 insect medium after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital, followed by cultivation for 10 hours in 1.0 mM phenobarbital-supplemented MGM-450 insect medium). Interestingly, the transcriptome diversities of cells cultured in media containing 0.25 mM phenobarbital after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital, followed by cultivation for 10 hours in 1.0 mM phenobarbital-supplemented MGM-450 insect medium) were different from cells cultured in media containing 0.25 mM phenobarbital after previous cultivation (cultivation for 80 hours in MGM-450 insect medium without phenobarbital). This hysteretic phenomenon of transcriptome diversities indicates multi-stability of the genome expression system. Cellular memories were recorded in genome expression networks as in DNA/histone modifications. PMID:26657512

Chemical and mineralogical analysis of devonian black-shale samples from Martin County, Kentucky; Carroll and Washington counties, Ohio; Wise County, Virginia; and Overton County, Tennessee, U.S.A.

USGS Publications Warehouse

Leventhal, J.S.; Hosterman, J.W.

1982-01-01

Core samples of Devonian shales from five localities in the Appalachian basin have been analyzed chemically and mineralogically. The amounts of major elements are similar; however, the minor constituents, organic C, S, phosphate and carbonate show ten-fold variations in amounts. Trace elements Mo, Ni, Cu, V, Co, U, Zn, Hg, As and Mn show variations in amounts that can be related to the minor constituents. All samples contain major amounts of quartz, illite, two types of mixed-layer clays, and chlorite in differing quantities. Pyrite, calcite, feldspar and kaolinite are also present in many samples in minor amounts. Dolomite, apatite, gypsum, barite, biotite and marcasite are present in a few samples in trace amounts. Trace elements listed above are strongly controlled by organic C with the exception of Mn which is associated with carbonate minerals. Amounts of organic C generally range from 3 to 6%, and S is in the range of 2-5%. Amounts of trace elements show the following general ranges in ppm (parts per million): Co, 20-40; Cu, 40-70; U, 10-40; As, 20-40; V, 150-300; Ni, 80-150; high values are as much as twice these values. The organic C was probably the concentrating agent, and the organic C and sulfide S together created an environment that immobilized and preserved these trace elements. Closely spaced samples showing an abrupt transition in color also show changes in organic C, S and trace-element contents. Several associations exist between mineral and chemical content. Pyrite and marcasite are the only minerals found to contain sulfide-S. In general, the illite-chlorite mixed-layer clay mineral shows covariation with organic C if calcite is not present. The enriched trace elements are not related to the clay types, although the clay and organic matter are intimately associated as the bulk fabric of the rock. ?? 1982.

High temperature desulfurization of synthesis gas

DOEpatents

Najjar, Mitri S.; Robin, Allen M.

1989-01-01

The hot process gas stream from the partial oxidation of sulfur-containing heavy liquid hydrocarbonaceous fuel and/or sulfur-containing solid carbonaceous fuel comprising gaseous mixtures of H.sub.2 +CO, sulfur-containing gases, entrained particulate carbon, and molten slag is passed through the unobstructed central passage of a radiant cooler where the temperature is reduced to a temperature in the range of about 1800.degree. F. to 1200.degree. F. From about 0 to 95 wt. % of the molten slag and/or entrained material may be removed from the hot process gas stream prior to the radiant cooler with substantially no reduction in temperature of the process gas stream. In the radiant cooler, after substantially all of the molten slag has solidified, the sulfur-containing gases are contacted with a calcium-containing material to produce calcium sulfide. A partially cooled stream of synthesis gas, reducing gas, or fuel gas containing entrained calcium sulfide particulate matter, particulate carbon, and solidified slag leaves the radiant cooler containing a greatly reduced amount of sulfur-containing gases.

9 CFR 317.361 - Nutrient content claims for the sodium content.

Code of Federal Regulations, 2010 CFR

2010-01-01

... dehydrated products that must be reconstituted before typical consumption with water or a diluent containing... before typical consumption with water or a diluent containing an insignificant amount, as defined in... insignificant amount of sodium”; and (iii) If the product meets these conditions without the benefit of special...

Identification and characterization of calcium transporter gene family in finger millet in relation to grain calcium content.

PubMed

Singh, Uma M; Metwal, Mamta; Singh, Manoj; Taj, Gohar; Kumar, Anil

2015-07-15

Calcium (Ca) is an essential mineral for proper growth and development of plants as well as animals. In plants including cereals, calcium is deposited in seed during its development which is mediated by specialized Ca transporters. Common cereal seeds contain very low amounts of Ca while the finger millet (Eleusine coracana) contains exceptionally high amounts of Ca in seed. In order to understand the role of Ca transporters in grain Ca accumulation, developing seed transcriptome of two finger millet genotypes (GP-1, low Ca and GP-45 high Ca) differing in seed Ca content was sequenced using Illumina paired-end sequencing technology and members of Ca transporter gene family were identified. Out of 109,218 and 120,130 contigs, 86 and 81 contigs encoding Ca transporters were identified in GP-1 and GP-45, respectively. After removal of redundant sequences, a total of 19 sequences were confirmed as Ca transporter genes, which includes 11 Ca(2+) ATPases, 07 Ca(2+)/cation exchangers and 01 Ca(2+) channel. The differential expressions of all genes were analyzed from transcriptome data and it was observed that 9 and 3 genes were highly expressed in GP-45 and GP-1 genotypes respectively. Validation of transcriptome expression data of selected Ca transporter genes was performed on different stages of developing spikes of both genotypes grown under different concentrations of exogenous Ca. In both genotypes, significant correlation was observed between the expression of these genes, especially EcCaX3, and on the amount of Ca accumulated in seed. The positive correlation of seed mass with the amount of Ca concentration was also observed. The efficient Ca transport property and responsiveness of EcCAX3 towards exogenous Ca could be utilized in future biofortification program. Copyright © 2015 Elsevier B.V. All rights reserved.

An Efficient Method for the Isolation of Highly Purified RNA from Seeds for Use in Quantitative Transcriptome Analysis.

PubMed

Kanai, Masatake; Mano, Shoji; Nishimura, Mikio

2017-01-11

Plant seeds accumulate large amounts of storage reserves comprising biodegradable organic matter. Humans rely on seed storage reserves for food and as industrial materials. Gene expression profiles are powerful tools for investigating metabolic regulation in plant cells. Therefore, detailed, accurate gene expression profiles during seed development are required for crop breeding. Acquiring highly purified RNA is essential for producing these profiles. Efficient methods are needed to isolate highly purified RNA from seeds. Here, we describe a method for isolating RNA from seeds containing large amounts of oils, proteins, and polyphenols, which have inhibitory effects on high-purity RNA isolation. Our method enables highly purified RNA to be obtained from seeds without the use of phenol, chloroform, or additional processes for RNA purification. This method is applicable to Arabidopsis, rapeseed, and soybean seeds. Our method will be useful for monitoring the expression patterns of low level transcripts in developing and mature seeds.

Increased brain uptake of targeted nanoparticles by adding an acid-cleavable linkage between transferrin and the nanoparticle core.

PubMed

Clark, Andrew J; Davis, Mark E

2015-10-06

Most therapeutic agents are excluded from entering the central nervous system by the blood-brain barrier (BBB). Receptor mediated transcytosis (RMT) is a common mechanism used by proteins, including transferrin (Tf), to traverse the BBB. Here, we prepared Tf-containing, 80-nm gold nanoparticles with an acid-cleavable linkage between the Tf and the nanoparticle core to facilitate nanoparticle RMT across the BBB. These nanoparticles are designed to bind to Tf receptors (TfRs) with high avidity on the blood side of the BBB, but separate from their multidentate Tf-TfR interactions upon acidification during the transcytosis process to allow release of the nanoparticle into the brain. These targeted nanoparticles show increased ability to cross an in vitro model of the BBB and, most important, enter the brain parenchyma of mice in greater amounts in vivo after systemic administration compared with similar high-avidity nanoparticles containing noncleavable Tf. In addition, we investigated this design with nanoparticles containing high-affinity antibodies (Abs) to TfR. With the Abs, the addition of the acid-cleavable linkage provided no improvement to in vivo brain uptake for Ab-containing nanoparticles, and overall brain uptake was decreased for all Ab-containing nanoparticles compared with Tf-containing ones. These results are consistent with recent reports of high-affinity anti-TfR Abs trafficking to the lysosome within BBB endothelium. In contrast, high-avidity, Tf-containing nanoparticles with the acid-cleavable linkage avoid major endothelium retention by shedding surface Tf during their transcytosis.

Comparative Corrosion Behavior of Two Palladium Containing Titanium Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lian, T; Yashiki, T; Nakayama, T

2006-02-05

The ASTM standard B 265 provides the requirements for the chemical composition of titanium (Ti) alloys. It is planned to use corrosion resistant and high strength titanium alloys to fabricate the drip shield at the proposed Yucca Mountain Repository. Titanium grade (Gr) 7 (R52400) and other Ti alloys are currently being characterized for this application. Ti Gr 7 contains 0.15% Palladium (Pd) to increase its corrosion performance. In this article we report results on the comparative short term corrosion behavior of Ti Gr 7 and a Ruthenium (Ru) containing alloy (Ti Gr 33). Ti Gr 33 also contains a smallmore » amount of Pd. Limited electrochemical testing such as polarization resistance and cyclic potentiodynamic curves showed that both alloys have a similar corrosion behavior in the tested environments.« less

COMPARATIVE CORROSION BEHAVIOR OF TWO PALLADIUM CONTAINING TITANIUM ALLOYS

DOE Office of Scientific and Technical Information (OSTI.GOV)

T. Lian, T. Yashiki, T. Nakayama, T. Nakanishi, R. B. Rebak

2006-07-23

The ASTM standard B 265 provides the requirements for the chemical composition of titanium (Ti) alloys. It is planned to use corrosion resistant and high strength titanium alloys to fabricate the drip shield at the proposed Yucca Mountain Repository. Titanium grade (Gr) 7 (R52400) and other Ti alloys are currently being characterized for this application. Ti Gr 7 contains 0.15% Palladium (Pd) to increase its corrosion performance. In this article we report results on the comparative short term corrosion behavior of Ti Gr 7 and a Ruthenium (Ru) containing alloy (Ti Gr 33). Ti Gr 33 also contains a smallmore » amount of Pd. Limited electrochemical testing such as polarization resistance and cyclic potentiodynamic curves showed that both alloys have a similar corrosion behavior in the tested environments.« less

Experimental quantum computing without entanglement.

PubMed

Lanyon, B P; Barbieri, M; Almeida, M P; White, A G

2008-11-14

Deterministic quantum computation with one pure qubit (DQC1) is an efficient model of computation that uses highly mixed states. Unlike pure-state models, its power is not derived from the generation of a large amount of entanglement. Instead it has been proposed that other nonclassical correlations are responsible for the computational speedup, and that these can be captured by the quantum discord. In this Letter we implement DQC1 in an all-optical architecture, and experimentally observe the generated correlations. We find no entanglement, but large amounts of quantum discord-except in three cases where an efficient classical simulation is always possible. Our results show that even fully separable, highly mixed, states can contain intrinsically quantum mechanical correlations and that these could offer a valuable resource for quantum information technologies.

Duplex sampling apparatus and method

DOEpatents

Brown, Paul E.; Lloyd, Robert

1992-01-01

An improved apparatus is provided for sampling a gaseous mixture and for measuring mixture components. The apparatus includes two sampling containers connected in series serving as a duplex sampling apparatus. The apparatus is adapted to independently determine the amounts of condensable and noncondensable gases in admixture from a single sample. More specifically, a first container includes a first port capable of selectively connecting to and disconnecting from a sample source and a second port capable of selectively connecting to and disconnecting from a second container. A second container also includes a first port capable of selectively connecting to and disconnecting from the second port of the first container and a second port capable of either selectively connecting to and disconnecting from a differential pressure source. By cooling a mixture sample in the first container, the condensable vapors form a liquid, leaving noncondensable gases either as free gases or dissolved in the liquid. The condensed liquid is heated to drive out dissolved noncondensable gases, and all the noncondensable gases are transferred to the second container. Then the first and second containers are separated from one another in order to separately determine the amount of noncondensable gases and the amount of condensable gases in the sample.

Separation of mouse testis cells on a Celsep (TM) apparatus and their usefulness as a source of high molecular weight DNA or RNA

NASA Technical Reports Server (NTRS)

Wolgemuth, D. J.; Gizang-Ginsberg, E.; Engelmyer, E.; Gavin, B. J.; Ponzetto, C.

1985-01-01

The use of a self-contained unit-gravity cell separation apparatus for separation of populations of mouse testicular cells is described. The apparatus, a Celsep (TM), maximizes the unit area over which sedimentation occurs, reduces the amount of separation medium employed, and is quite reproducible. Cells thus isolated have been good sources for isolation of DNA, and notably, high molecular weight RNA.

Absence of TGF-β Receptor Activation by Highly Purified hCG Preparations.

PubMed

Koistinen, Hannu; Hautala, Laura; Koli, Katri; Stenman, Ulf-Håkan

2015-12-01

Recently, several LH/human chorionic gonadotropin (hCG) receptor-independent activities for hCG have been described, including activation of the TGF-β receptor (TGFβR) by hyperglycosylated hCG and stimulation of trophoblast invasion. Because the hCG concentrations used in these studies have been rather high, reflecting physiological hCG levels in pregnancy, even a minor contamination with growth factors, which act at very low concentrations, may be significant. Several commercial hCG preparations have been found to contain significant amounts of epidermal growth factor (EGF), which we also confirmed here. Furthermore, we found that some hCG preparations also contain significant amounts of TGF-β1. These hCG preparations were able to activate ERK1/2 in JEG-3 choriocarcinoma cells or TGFβR in mink lung epithelial cells transfected with a reporter gene for TGFβR activation. No such activation was found with highly purified hCG or its free β-subunit (hCGβ), irrespective of whether they were hyperglycosylated or not. Taken together, our results suggest that the growth factor contaminations in the hCG preparations can cause activation of TGFβR and, at least in JEG-3 cells, MAPK signaling. This highlights the importance to carefully control for potential contaminations and that highly purified hCG preparations have to be used for biological studies.

Absence of TGF-β Receptor Activation by Highly Purified hCG Preparations

PubMed Central

Hautala, Laura; Koli, Katri; Stenman, Ulf-Håkan

2015-01-01

Recently, several LH/human chorionic gonadotropin (hCG) receptor-independent activities for hCG have been described, including activation of the TGF-β receptor (TGFβR) by hyperglycosylated hCG and stimulation of trophoblast invasion. Because the hCG concentrations used in these studies have been rather high, reflecting physiological hCG levels in pregnancy, even a minor contamination with growth factors, which act at very low concentrations, may be significant. Several commercial hCG preparations have been found to contain significant amounts of epidermal growth factor (EGF), which we also confirmed here. Furthermore, we found that some hCG preparations also contain significant amounts of TGF-β1. These hCG preparations were able to activate ERK1/2 in JEG-3 choriocarcinoma cells or TGFβR in mink lung epithelial cells transfected with a reporter gene for TGFβR activation. No such activation was found with highly purified hCG or its free β-subunit (hCGβ), irrespective of whether they were hyperglycosylated or not. Taken together, our results suggest that the growth factor contaminations in the hCG preparations can cause activation of TGFβR and, at least in JEG-3 cells, MAPK signaling. This highlights the importance to carefully control for potential contaminations and that highly purified hCG preparations have to be used for biological studies. PMID:26495869

Weathering the storm: how lodgepole pine trees survive mountain pine beetle outbreaks.

PubMed

Erbilgin, Nadir; Cale, Jonathan A; Hussain, Altaf; Ishangulyyeva, Guncha; Klutsch, Jennifer G; Najar, Ahmed; Zhao, Shiyang

2017-06-01

Recent mountain pine beetle outbreaks in western North America killed millions of lodgepole pine trees, leaving few survivors. However, the mechanism underlying the ability of trees to survive bark beetle outbreaks is unknown, but likely involve phytochemicals such as monoterpenes and fatty acids that can drive beetle aggregation and colonization on their hosts. Thus, we conducted a field survey of beetle-resistant lodgepole pine (Pinus contorta) trees to retrospectively deduce whether these phytochemicals underlie their survival by comparing their chemistry to that of non-attacked trees in the same stands. We also compared beetle attack characteristics between resistant and beetle-killed trees. Beetle-killed trees had more beetle attacks and longer ovipositional galleries than resistant trees, which also lacked the larval establishment found in beetle-killed trees. Resistant trees contained high amounts of toxic and attraction-inhibitive compounds and low amounts of pheromone-precursor and synergist compounds. During beetle host aggregation and colonization, these compounds likely served three critical roles in tree survival. First, low amounts of pheromone-precursor (α-pinene) and synergist (mycrene, terpinolene) compounds reduced or prevented beetles from attracting conspecifics to residual trees. Second, high amounts of 4-allyanisole further inhibited beetle attraction to its pheromone. Finally, high amounts of toxic limonene, 3-carene, 4-allyanisole, α-linolenic acid, and linoleic acid inhibited beetle gallery establishment and oviposition. We conclude that the variation of chemotypic expression of local plant populations can have profound ecological consequences including survival during insect outbreaks.

Determination of selected neurotoxic insecticides in small amounts of animal tissue utilizing a newly constructed mini-extractor.

PubMed

Seifertová, Marta; Čechová, Eliška; Llansola, Marta; Felipo, Vicente; Vykoukalová, Martina; Kočan, Anton

2017-10-01

We developed a simple analytical method for the simultaneous determination of representatives of various groups of neurotoxic insecticides (carbaryl, chlorpyrifos, cypermethrin, and α-endosulfan and β-endosulfan and their metabolite endosulfan sulfate) in limited amounts of animal tissues containing different amounts of lipids. Selected tissues (rodent fat, liver, and brain) were extracted in a special in-house-designed mini-extractor constructed on the basis of the Soxhlet and Twisselmann extractors. A dried tissue sample placed in a small cartridge was extracted, while the nascent extract was simultaneously filtered through a layer of sodium sulfate. The extraction was followed by combined clean-up, including gel permeation chromatography (in case of high lipid content), ultrasonication, and solid-phase extraction chromatography using C 18 on silica and aluminum oxide. Gas chromatography coupled with high-resolution mass spectrometry was used for analyte separation, detection, and quantification. Average recoveries for individual insecticides ranged from 82 to 111%. Expanded measurement uncertainties were generally lower than 35%. The developed method was successfully applied to rat tissue samples obtained from an animal model dealing with insecticide exposure during brain development. This method may also be applied to the analytical treatment of small amounts of various types of animal and human tissue samples. A significant advantage achieved using this method is high sample throughput due to the simultaneous treatment of many samples. Graphical abstract Optimized workflow for the determination of selected insecticides in small amounts of animal tissue including newly developed mini-extractor.

The Draft Genome Sequence of a Novel High-Efficient Butanol-Producing Bacterium Clostridium Diolis Strain WST.

PubMed

Chen, Chaoyang; Sun, Chongran; Wu, Yi-Rui

2018-03-21

A wild-type solventogenic strain Clostridium diolis WST, isolated from mangrove sediments, was characterized to produce high amount of butanol and acetone with negligible level of ethanol and acids from glucose via a unique acetone-butanol (AB) fermentation pathway. Through the genomic sequencing, the assembled draft genome of strain WST is calculated to be 5.85 Mb with a GC content of 29.69% and contains 5263 genes that contribute to the annotation of 5049 protein-coding sequences. Within these annotated genes, the butanol dehydrogenase gene (bdh) was determined to be in a higher amount from strain WST compared to other Clostridial strains, which is positively related to its high-efficient production of butanol. Therefore, we present a draft genome sequence analysis of strain WST in this article that should facilitate to further understand the solventogenic mechanism of this special microorganism.

Organ-specific distribution of phenolic compounds in bilberry (Vaccinium myrtillus) and 'northblue' blueberry (Vaccinium corymbosum x V. angustifolium).

PubMed

Riihinen, Kaisu; Jaakola, Laura; Kärenlampi, Sirpa; Hohtola, Anja

2008-09-01

Blueberries and bilberries are recognized as some of the best sources of flavonoids, especially anthocyanins. The contents of flavonoids (anthocyanins, proanthocyanidins, flavonols) and hydroxycinnamic acids in the flower, fruit skin and pulp, leaf and rhizome of bilberry and the blueberry cultivar 'Northblue' were analyzed using high-performance liquid chromatography combined with diode-array detection. The most striking difference in the fruits was the predominance of hydroxycinnamic acids in blueberry, whereas in bilberry the anthocyanin content was much higher, particularly in the pulp. Differences in flavonoid contents of fruits were already apparent at the flower stage. Bilberry and blueberry leaves both contained high amounts of proanthocyanidins, flavonols and hydroxycinnamic acids. Blueberry rhizomes accumulated high amounts of hydroxycinnamic acids. All plant parts of bilberry and blueberry are potential sources of phenolic compounds for use either as dietary botanicals or by the pharmaceutical industry. Copyright © 2008 Elsevier Ltd. All rights reserved.

Application of alkyne-TCNQ addition reaction to polymerization.

PubMed

Washino, Yusuke; Michinobu, Tsuyoshi

2011-04-19

The polymerization using a high-yielding addition reaction between electron-rich alkynes and 7,7,8,8-tetracyanoquinodimethane (TCNQ) derivatives is described. The bifunctional monomer containing two TCNQ moieties and the counter comonomer bearing two dialkylaniline (DAA)-substituted alkynes are reacted in 1,2-dichloroethane under mild heating conditions. At the high monomer concentrations, high molecular weight linear polymers are obtained, while the reaction at the low monomer concentrations produces a significant amount of the cyclic compounds. A clear relationship between the monomer concentration and the cyclic compound amount is demonstrated. The obtained polymers feature a sufficient thermal stability with the decomposition temperature exceeding 300  °C as well as strong charge-transfer (CT) bands and redox activities ascribed to the produced donor-acceptor moieties. These features are also used to optimize the polymerization conditions and to estimate the chemical structures. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Geology and ground-water resources of Hays County, Texas

USGS Publications Warehouse

DeCook, Kenneth James

1963-01-01

Ground water from wells in the Pearsall formation generally contains less than 500 parts per million of dissolved solids. Water from the Glen Rose limestone in some places contains more than 500 parts per million of sulfate and more than 1,000 parts per million of dissolved solids; locally it is high in nitrate also. Except in the southeastern part of the county, water from the Edwards limestone is commonly very hard but is otherwise of good quality for most uses. Analyses of two water samples from the Austin chalk indicate a high content of bicarbonate. Water from the Taylor marl and from Quaternary sediments generally is hard, and locally it contains excessive nitrate. Most wells in Hays County are used for domestic and stock supplies. About 20 wells, most of them in the Edwards limestone, yield water in relatively large amounts for industrial use, irrigation, or public supplies.

A Stable Polymer Burnable Poison Material With Special Attributes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tulenko, James S.; Baney, Ronald H.; Pressley, Linda

2002-07-01

The University of Florida (UF) is carrying out basic research on a new class of thermally stable boron containing materials which appear to have special properties that will greatly enhance the performance of Burnable Poison Rod Assemblies (BPRA) and also Spent Fuel Containers (SFC). This new material ('Carborane') has the special properties of containing a tailored amount of boron, an extremely high hydrogen content, and being extremely stable to high temperatures. 'Carborane' reduces the water displacement penalty by 59% by the hydrogen present in the 'Carborane'. In addition to increasing safety margins, a cost benefit of approximately $500,000 per two-yearmore » cycle is projected from reduced enrichments, resulting from the use of this burnable poison material, making it no longer necessary to offset the water displacement reactivity penalty. This research program is supported by a Department of Energy NEER grant. (authors)« less

Anthocyanin and Carotenoid Contents in Different Cultivars of Chrysanthemum (Dendranthema grandiflorum Ramat.) Flower.

PubMed

Park, Chang Ha; Chae, Soo Cheon; Park, Soo-Yun; Kim, Jae Kwang; Kim, Yong Joo; Chung, Sun Ok; Arasu, Mariadhas Valan; Al-Dhabi, Naif Abdullah; Park, Sang Un

2015-06-15

The flowers of twenty-three cultivars of Dendranthema grandiflorum Ramat. were investigated to determine anthocyanin and carotenoid levels and to confirm the effects of the pigments on the flower colors using high-performance liquid chromatography (HPLC) and electrospray ionization-mass spectrometry (ESI-MS). The cultivars contained the anthocyanins cyanidin 3-glucoside (C3g) and cyanidin 3-(3"-malonoyl) glucoside (C3mg) and the following carotenoids: lutein, zeaxanthin, β-cryptoxanthin, 13-cis-β-carotene, α-carotene, trans-β-carotene, and 9-cis-β-carotene. The cultivar "Magic" showed the greatest accumulation of total and individual anthocyanins, including C3g and C3gm. On the other hand, the highest level of lutein and zeaxanthin was noted in the cultivar "Il Weol". The cultivar "Anastasia" contained the highest amount of carotenoids such as trans-β-carotene, 9-cis-β-carotene, and 13-cis-β-carotene. The highest accumulation of β-cryptoxanthin and α-carotene was noted in the cultivar "Anastasia" and "Il Weol". Our results suggested that 'Magic", "Angel" and "Relance' had high amounts of anthocyanins and showed a wide range of red and purple colors in their petals, whereas "Il Weol', "Popcorn Ball' and "Anastasia" produced higher carotenoid contents and displayed yellow or green petal colors. Interestingly, "Green Pang Pang", which contained a high level of anthocyanins and a medium level of carotenoids, showed the deep green colored petals. "Kastelli", had high level of carotenoids as well as a medium level of anthocyanins and showed orange and red colored petals. It was concluded that each pigment is responsible for the petal's colors and the compositions of the pigments affect their flower colors and that the cultivars could be a good source for pharmaceutical, floriculture, and pigment industries.

Mice deficient in mitochondrial glycerol-3-phosphate acyltransferase-1 have diminished myocardial triacylglycerol accumulation during lipogenic diet and altered phospholipid fatty acid composition

PubMed Central

Lewin, Tal M.; de Jong, Hendrik; Schwerbrock, Nicole J. M.; Hammond, Linda E.; Watkins, Steven M.; Combs, Terry P.; Coleman, Rosalind A.

2008-01-01

Glycerol-3-phosphate acyltransferase-1 (GPAT1), which is located on the outer mitochondrial membrane comprises up to 30% of total GPAT activity in the heart. It is one of at least four mammalian GPAT isoforms known to catalyze the initial, committed, and rate limiting step of glycerolipid synthesis. Because excess triacylglycerol (TAG) accumulates in cardiomyocytes in obesity and type 2 diabetes, we determined whether lack of GPAT1 would alter the synthesis of heart TAG and phospholipids after a 2-week high sucrose diet or a 3-month high fat diet. Even in the absence of hypertriglyceridemia, TAG increased 2-fold with both diets in hearts from wildtype mice. In contrast, hearts from Gpat1−/− mice contained 20–80% less TAG than the wildtype controls. In addition, hearts from Gpat1−/− mice fed the high-sucrose diet incorporate 60% less [14C]palmitate into heart TAG as compared to wildtype mice. Because GPAT1 prefers 16:0-CoA to other long chain acyl-CoA substrates, we determined the fatty acid composition of heart phospholipids. Compared to wildtype littermate controls, hearts from Gpat1−/− mice contained a lower amount of 16:0 in phosphatidylcholine, phosphatidylethanolamine, and phosphatidylserine/phosphatidylinositol and significantly more C20:4n6. Phosphatidylcholine and phosphatidylethanolamine from Gpat1−/− hearts also contained higher amounts of 18:0 and 18:1. Although at least three other GPAT isoforms are expressed in the heart, our data suggest that GPAT1 contributes significantly to cardiomyocyte TAG synthesis during lipogenic or high fat diets and influences the incorporation of 20:4n6 into heart phospholipids. PMID:18522808

Characterization of feed coal and coal combustion products from power plants in Indiana and Kentucky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brownfield, M.E.; Affolter, R.H.; Cathcart, J.D.

1999-07-01

The US Geological Survey, Kentucky Geological Survey, and the University of Kentucky Center for Applied Energy Research are collaborating with Indiana and Kentucky utilities to determine the physical and chemical properties of feed coal and coal combustion products (CCP) from three coal-fired power plants. These three plants are designated as Units K1, K2, and I1 and burn high-, moderate-, and low-sulfur coals, respectively. Over 200 samples of feed coal and CCP were analyzed by various chemical and mineralogical methods to determine mode of occurrence and distribution of trace elements in the CCP. Generally, feed coals from all 3 Units containmore » mostly well-crystallized kaolinite and quartz. Comparatively, Unit K1 feed coals have higher amounts of carbonates, pyrite and sphalerite. Unit K2 feed coals contain higher kaolinite and illite/muscovite when compared to Unit K1 coals. Unit I1 feed coals contain beta-form quartz and alumino-phosphates with minor amounts of calcite, micas, anatase, and zircon when compared to K1 and K2 feed coals. Mineralogy of feed coals indicate that the coal sources for Units K1 and K2 are highly variable, with Unit K1 displaying the greatest mineralogic variability; Unit I1 feed coal however, displayed little mineralogic variation supporting a single source. Similarly, element contents of Units K1 and K2 feed coals show more variability than those of Unit I1. Fly ash samples from Units K1 and K2 consist mostly of glass, mullite, quartz, and spines group minerals. Minor amounts of illite/muscovite, sulfates, hematite, and corundum are also present. Spinel group minerals identified include magnetite, franklinite, magnesioferrite, trevorite, jacobisite, and zincochromite. Scanning Electron Microscope analysis reveals that most of the spinel minerals are dendritic intergrowths within aluminum silicate glass. Unit I1 fly ash samples contain glass, quartz, perovskite, lime, gehlenite, and apatite with minor amounts of periclase, anhydrite, carbonates, pyroxenes, and spinels. The abundant Ca mineral phases in the Unit I1 fly ashes are attributed to the presence of carbonate, clay and phosphate minerals in the coal.« less

Seasonal changes in minor membrane phospholipid classes, sterols and tocopherols in overwintering insect, Pyrrhocoris apterus.

PubMed

Koštál, Vladimír; Urban, Tomáš; Rimnáčová, Lucie; Berková, Petra; Simek, Petr

2013-09-01

Ectotherm animals including insects are known to undergo seasonal restructuring of the cell membranes in order to keep their functionality and/or protect their structural integrity at low body temperatures. Studies on insects so far focused either on fatty acids or on composition of molecular species in major phospholipid classes. Here we extend the scope of analysis and bring results on seasonal changes in minor phospholipid classes, lysophospholipids (LPLs), free fatty acids, phytosterols and tocopherols in heteropteran insect, Pyrrhocoris apterus. We found that muscle tissue contains unusually high amounts of LPLs. Muscle and fat body tissues also contain high amounts of β-sitosterol and campesterol, two phytosterols derived from plant food, while only small amounts of cholesterol are present. In addition, two isomers (γ and δ) of tocopherol (vitamin E) are present in quantities comparable to, or even higher than phytosterols in both tissues. Distinct seasonal patterns of sterol and tocopherol concentrations were observed showing a minimum in reproductively active bugs in summer and a maximum in diapausing, cold-acclimated bugs in winter. Possible adaptive meanings of such changes are discussed including: preventing the unregulated transition of membrane lipids from functional liquid crystalline phase to non-functional gel phase; decreasing the rates of ion/solute leakage; silencing the activities of membrane bound enzymes and receptors; and counteracting the higher risk of oxidative damage to PUFA in winter membranes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Toxic metals in WEEE: characterization and substance flow analysis in waste treatment processes.

PubMed

Oguchi, Masahiro; Sakanakura, Hirofumi; Terazono, Atsushi

2013-10-01

Waste electrical and electronic equipment (WEEE) has received extensive attention as a secondary source of metals. Because WEEE also contains toxic substances such as heavy metals, appropriate management of these substances is important in the recycling and treatment of WEEE. As a basis for discussion toward better management of WEEE, this study characterizes various types of WEEE in terms of toxic metal contents. The fate of various metals contained in WEEE, including toxic metals, was also investigated in actual waste treatment processes. Cathode-ray tube televisions showed the highest concentration and the largest total amount of toxic metals such as Ba, Pb, and Sb, so appropriate recycling and disposal of these televisions would greatly contribute to better management of toxic metals in WEEE. A future challenge is the management of toxic metals in mid-sized items such as audio/visual and ICT equipment because even though the concentrations were not high in these items, the total amount of toxic metals contained in them is not negligible. In the case of Japan, such mid-sized WEEE items as well as small electronic items are subject to municipal solid waste treatment. A case study showed that a landfill was the main destination of toxic metals contained in those items in the current treatment systems. The case study also showed that changes in the flows of toxic metals will occur when treatment processes are modified to emphasize resource recovery. Because the flow changes might lead to an increase in the amount of toxic metals released to the environment, the flows of toxic metals and the materials targeted for resource recovery should be considered simultaneously. Copyright © 2012 Elsevier B.V. All rights reserved.

Anaerobic Coculture of Microalgae with Thermosipho globiformans and Methanocaldococcus jannaschii at 68°C Enhances Generation of n-Alkane-Rich Biofuels after Pyrolysis

PubMed Central

Matsuyama, Shigeru; Igarashi, Kensuke; Utsumi, Motoo; Shiraiwa, Yoshihiro; Kuwabara, Tomohiko

2013-01-01

We tested different alga-bacterium-archaeon consortia to investigate the production of oil-like mixtures, expecting that n-alkane-rich biofuels might be synthesized after pyrolysis. Thermosipho globiformans and Methanocaldococcus jannaschii were cocultured at 68°C with microalgae for 9 days under two anaerobic conditions, followed by pyrolysis at 300°C for 4 days. Arthrospira platensis (Cyanobacteria), Dunaliella tertiolecta (Chlorophyta), Emiliania huxleyi (Haptophyta), and Euglena gracilis (Euglenophyta) served as microalgal raw materials. D. tertiolecta, E. huxleyi, and E. gracilis cocultured with the bacterium and archaeon inhibited their growth and CH4 production. E. huxleyi had the strongest inhibitory effect. Biofuel generation was enhanced by reducing impurities containing alkanenitriles during pyrolysis. The composition and amounts of n-alkanes produced by pyrolysis were closely related to the lipid contents and composition of the microalgae. Pyrolysis of A. platensis and D. tertiolecta containing mainly phospholipids and glycolipids generated short-carbon-chain n-alkanes (n-tridecane to n-nonadecane) and considerable amounts of isoprenoids. E. gracilis also produced mainly short n-alkanes. In contrast, E. huxleyi containing long-chain (31 and 33 carbon atoms) alkenes and very long-chain (37 to 39 carbon atoms) alkenones, in addition to phospholipids and glycolipids, generated a high yield of n-alkanes of various lengths (n-tridecane to n-pentatriacontane). The gas chromatography-mass spectrometry (GC-MS) profiles of these n-alkanes were similar to those of native petroleum crude oils despite containing a considerable amount of n-hentriacontane. The ratio of phytane to n-octadecane was also similar to that of native crude oils. PMID:23183975

Growth performance, haematological traits, meat variables, and effects of treadmill and transport stress in veal calves supplied different amounts of iron.

PubMed

Lindt, F; Blum, J W

1994-06-01

Effects of serum iron (Fe), haematological variables and on blood lactate levels before and after treadmill exercise or transport to the slaughterhouse, on meat traits, and on growth performance of feeding milk replacer (MR), planned to contain 10, 20, 30, 40, 50 or 80 mg Fe/kg, were studied in veal calves. If supplied less than 50 mg Fe/kg MR, calves developed hypoferraemia and anaemia, the degree of which was dependent on Fe intake. Serum Fe concentration, saturation of transferrin with Fe and the degree of anaemia in calves fed 20 or 10 mg Fe/kg MR were nearly identical. Serum Fe concentration and haematological traits barely changed in calves fed 50 mg Fe/kg MR during the growth trail, but serum Fe concentration increased when MR contained 80 mg Fe/kg in calves fed 50 or more Fe/kg MR. Growth performance was smaller in calves fed 10 mg Fe/kg MR than in those fed greater amounts of Fe/kg MR. Carcass taxation was inversely related to Fe intake. In conclusion, MR containing only 10 mg Fe/kg caused marked anaemia and reduced growth performance. Feeding MR with only 20 mg Fe/kg is not necessarily sufficient to prevent development of severe anaemia. Feeding MR with 50 mg Fe/kg would seem to be physiologically the most appropriate amount of Fe for veal calves, but was too high for acceptable carcass taxation.

7 CFR 252.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Donated food value return system means a system used by a processor or distributor to reduce the price of... issued to a distributor in an amount equal to the NCP contract value of donated foods contained in an end... recipient agency in an amount equal to the NCP contract value of donated foods contained in an end product...

33 CFR 158.210 - Ports and terminals loading crude oil.

Code of Federal Regulations, 2010 CFR

2010-07-01

...); (b) Bilge water containing oily mixtures in the amount of 10 metric tons (11 short tons) or 2 metric...) Ballast water containing oily mixtures in the amount of 30% of the deadweight tonnage of the largest of... Criteria for Reception Facilities: Oily Mixtures § 158.210 Ports and terminals loading crude oil. The...

33 CFR 158.210 - Ports and terminals loading crude oil.

Code of Federal Regulations, 2013 CFR

2013-07-01

...); (b) Bilge water containing oily mixtures in the amount of 10 metric tons (11 short tons) or 2 metric...) Ballast water containing oily mixtures in the amount of 30% of the deadweight tonnage of the largest of... Criteria for Reception Facilities: Oily Mixtures § 158.210 Ports and terminals loading crude oil. The...

33 CFR 158.210 - Ports and terminals loading crude oil.

Code of Federal Regulations, 2011 CFR

2011-07-01

...); (b) Bilge water containing oily mixtures in the amount of 10 metric tons (11 short tons) or 2 metric...) Ballast water containing oily mixtures in the amount of 30% of the deadweight tonnage of the largest of... Criteria for Reception Facilities: Oily Mixtures § 158.210 Ports and terminals loading crude oil. The...

33 CFR 158.210 - Ports and terminals loading crude oil.

Code of Federal Regulations, 2014 CFR

2014-07-01

...); (b) Bilge water containing oily mixtures in the amount of 10 metric tons (11 short tons) or 2 metric...) Ballast water containing oily mixtures in the amount of 30% of the deadweight tonnage of the largest of... Criteria for Reception Facilities: Oily Mixtures § 158.210 Ports and terminals loading crude oil. The...

33 CFR 158.210 - Ports and terminals loading crude oil.

Code of Federal Regulations, 2012 CFR

2012-07-01

...); (b) Bilge water containing oily mixtures in the amount of 10 metric tons (11 short tons) or 2 metric...) Ballast water containing oily mixtures in the amount of 30% of the deadweight tonnage of the largest of... Criteria for Reception Facilities: Oily Mixtures § 158.210 Ports and terminals loading crude oil. The...

14 CFR 232.2 - Answers to applications for review.

Code of Federal Regulations, 2010 CFR

2010-01-01

... expected actual density of mail which will be tendered to the carrier if the order in question is upheld... order in question is upheld; (5) The volume (including density of mail, amount and types of containers... (including density of mail, amount and types of containers) of mail historically carried on the flight or...

PLUTONIUM ALLOYS CONTAINING CONTROLLED AMOUNTS OF PLUTONIUM ALLOTROPES OBTAINED BY APPLICATION OF HIGH PRESSURES

DOEpatents

Elliott, R.O.; Gschneidner, K.A. Jr.

1962-07-10

A method of making stabilized plutonium alloys which are free of voids and cracks and have a controlled amount of plutonium allotropes is described. The steps include adding at least 4.5 at.% of hafnium, indium, or erbium to the melted plutonium metal, homogenizing the resulting alloy at a temperature of 450 deg C, cooling to room temperature, and subjecting the alloy to a pressure which produces a rapid increase in density with a negligible increase in pressure. The pressure required to cause this rapid change in density or transformation ranges from about 800 to 2400 atmospheres, and is dependent on the alloying element. (AEC)

Experimental evaluation of atmospheric effects on radiometric measurements using the EREP of Skylab. [Salton Sea and Great Salt Lake

NASA Technical Reports Server (NTRS)

Chang, D. T. (Principal Investigator); Isaacs, R. G.

1975-01-01

The author has identified the following significant results. Test sites were located near the Great Salt Lake and the Salton Sea. Calculations were performed for a set of atmospheric models corresponding to the test sites, in addition to standard models for summer and winter midlatitude atmospheres with respective integrated water vapor amount of 2.4 g/sq cm and 0.9 g/sq cm. Each atmosphere was found to contain an average amount of continental aerosol. Computations were valid for high solar elevation angles. Atmospheric attenuation quantities were computed in addition to simulated EREP S192 radiances.

[Fast food promotes weight gain].

PubMed

Stender, Steen; Dyerberg, Jørn; Astrup, Arne V

2007-05-07

The total amounts of fat in a fast food menu consisting of French fries and fried Chicken Nuggets from McDonald's and KFC, respectively, bought in 35 different countries vary from 41 to 71 gram. In most countries the menu contained unacceptably high amounts of industrially-produced trans fat which contributes to an increased risk of ischaemic heart disease, weight gain, abdominal fat accumulation and type 2 diabetes. The quality of the ingredients in fast food ought to be better and the size of the portions smaller and less energy-dense so that frequent fast food meals do not increase the risk of obesity and diseases among customers.

Constraining 17O and 27Al NMR spectra of high-pressure crystals and glasses: New data for jadeite, pyrope, grossular, and mullite

USGS Publications Warehouse

Kelsey, K.E.; Stebbins, J.F.; Du, L.-S.; Hankins, B.

2007-01-01

The 17O NMR spectra of glasses quenched from melts at high pressure are often difficult to interpret due to overlapping peaks and lack of crystalline model compounds. High-pressure aluminosilicate glasses often contain significant amounts of [5]Al and [6]Al, thus these high-pressure glasses must contain oxygen bonded to high-coordinated aluminum. The 17O NMR parameters for the minerals jadeite, pyrope, grossular, and mullite are presented to assist interpretation of glass spectra and to help test quantum chemical calculations. The 17O NMR parameters for jadeite and grossular support previous peak assignments of oxygen bonded to Si and high-coordinated Al in high-pressure glasses as well as quantum chemical calculations. The oxygen tricluster in mullite is very similar to the previously observed tricluster in grossite (CaAl4 O7) and suspected triclusters in glasses. We also present 27Al NMR spectra for pyrope, grossular, and mullite.

Reactor and method for hydrocracking carbonaceous material

DOEpatents

Duncan, Dennis A.; Beeson, Justin L.; Oberle, R. Donald; Dirksen, Henry A.

1980-01-01

Solid, carbonaceous material is cracked in the presence of hydrogen or other reducing gas to provide aliphatic and aromatic hydrocarbons of lower molecular weight for gaseous and liquid fuels. The carbonaceous material, such as coal, is entrained as finely divided particles in a flow of reducing gas and preheated to near the decomposition temperature of the high molecular weight polymers. Within the reactor, small quantities of oxygen containing gas are injected at a plurality of discrete points to burn corresponding amounts of the hydrogen or other fuel and elevate the mixture to high temperatures sufficient to decompose the high molecular weight, carbonaceous solids. Turbulent mixing at each injection point rapidly quenches the material to a more moderate bulk temperature. Additional quenching after the final injection point can be performed by direct contact with quench gas or oil. The reactions are carried out in the presence of a hydrogen-containing reducing gas at moderate to high pressure which stabilizes the products.

Microstructure and mechanical properties of rapidly solidified B2-type Zr–Co alloys containing a second phase of Zr2Co

NASA Astrophysics Data System (ADS)

Li, Peiyou

2018-04-01

Microstructure and mechanical properties of B2-type Zr–Co alloys containing a second phase (Zr2Co) were investigated. Results show that the as-cast Zr52Co48, Zr54Co46, and Zr56Co44 alloys are composed of a eutectic structure of B2 and Zr2Co phases. Relative amounts of Zr2Co phases increase with an increase in Zr content. Zr54Co46 exhibits high yield strength, high Vickers hardness, good ductility, and high toughness values, and thus, Zr54Co46 can be considered to be a novel engineering material. The increase in strength and decrease in plastic strain of the alloys are mainly attributed to the increase in high strength of the brittle Zr2Co phase and to grain refining of the B2 matrix phase.

Lightweight sheet molding compound (SMC) composites containing cellulose nanocrystals

Treesearch

Amir Asadi; Mark Miller; Arjun V. Singh; Robert J. Moon; Kyriaki Kalaitzidou

2017-01-01

A scalable technique was introduced to produce high volume lightweight composites using sheet molding compound (SMC) manufacturing method by replacing 10 wt% glass fibers (GF) with a small amount of cellulose nanocrystals (CNC). The incorporation of 1 and 1.5 wt% CNC by dispersing in the epoxy matrix of short GF/epoxy SMC composites with 25 wt% GF content (25GF/CNC-...

40 CFR Appendix A to Part 191 - Table for Subpart B

Code of Federal Regulations, 2010 CFR

2010-07-01

... amount of spent nuclear fuel containing 1,000 metric tons of heavy metal (MTHM) exposed to a burnup between 25,000 megawatt-days per metric ton of heavy metal (MWd/MTHM) and 40,000 MWd/MTHM; (b) The high... heavy metal in the reactor fuel that created the waste, or to determine the average burnup that the fuel...

40 CFR Appendix A to Part 191 - Table for Subpart B

Code of Federal Regulations, 2013 CFR

2013-07-01

... amount of spent nuclear fuel containing 1,000 metric tons of heavy metal (MTHM) exposed to a burnup between 25,000 megawatt-days per metric ton of heavy metal (MWd/MTHM) and 40,000 MWd/MTHM; (b) The high... heavy metal in the reactor fuel that created the waste, or to determine the average burnup that the fuel...

40 CFR Appendix A to Part 191 - Table for Subpart B

Code of Federal Regulations, 2012 CFR

2012-07-01

... amount of spent nuclear fuel containing 1,000 metric tons of heavy metal (MTHM) exposed to a burnup between 25,000 megawatt-days per metric ton of heavy metal (MWd/MTHM) and 40,000 MWd/MTHM; (b) The high... heavy metal in the reactor fuel that created the waste, or to determine the average burnup that the fuel...

40 CFR Appendix A to Part 191 - Table for Subpart B

Code of Federal Regulations, 2014 CFR

2014-07-01

... amount of spent nuclear fuel containing 1,000 metric tons of heavy metal (MTHM) exposed to a burnup between 25,000 megawatt-days per metric ton of heavy metal (MWd/MTHM) and 40,000 MWd/MTHM; (b) The high... heavy metal in the reactor fuel that created the waste, or to determine the average burnup that the fuel...

40 CFR Appendix A to Part 191 - Table for Subpart B

Code of Federal Regulations, 2011 CFR

2011-07-01

... amount of spent nuclear fuel containing 1,000 metric tons of heavy metal (MTHM) exposed to a burnup between 25,000 megawatt-days per metric ton of heavy metal (MWd/MTHM) and 40,000 MWd/MTHM; (b) The high... heavy metal in the reactor fuel that created the waste, or to determine the average burnup that the fuel...

Reconnaissance for uranium in asphalt-bearing rocks in the western states

USGS Publications Warehouse

Hail, William James

1955-01-01

Evaluation of field data indicates that naturally occurring asphalts with a relatively high uranium content probably originated in, or migrated through, rocks that contain more than average amounts of uranium. It is believed that some of the uranium was present as an original constituent of the oil but that some uranium may have been introduced during migration of the oil.

Spatial allocation of market and nonmarket values in wildland fire management: A case study

Treesearch

John W. Benoit; Armando González-Cabán; Francis M. Fujioka; Shyh-Chin Chen; José J. Sanchez

2013-01-01

We developed a methodology to evaluate the efficacy of fuel treatments by estimating their costs and potential costs/losses with and without treatments in the San Jacinto Ranger District of the San Bernardino National Forest, California. This district is a typical southern California forest complex containing a large amount of high-valued real estate. We chose four...

Oil, fatty acid, flavonoid, and resveratrol content variability in FAD2A functional SNP genotypes in the U.S. peanut mini-core collection

USDA-ARS?s Scientific Manuscript database

Peanut seeds contain high amounts of oil and protein as well as some useful bioactive phytochemicals which can contribute to human health. The U.S. peanut mini-core collection is an important genetic resource for improving seed quality and developing new cultivars. Variability of seed chemical compo...

Method to synthesize and produce thin films by spray pyrolysis

DOEpatents

Squillante, Michael R.

1982-06-22

Forming a film by spraying onto a heated substrate an atomized solution containing the appropriate salt of a constituent element of the film and a highly soluble (i.e., greater than 1 M) organic acid in sufficient amount to reduce the oxidation state of at least one solute element of the spray solution after contacting the heated substrate.

Structure Prediction and Analysis of DNA Transposon and LINE Retrotransposon Proteins*

PubMed Central

Abrusán, György; Zhang, Yang; Szilágyi, András

2013-01-01

Despite the considerable amount of research on transposable elements, no large-scale structural analyses of the TE proteome have been performed so far. We predicted the structures of hundreds of proteins from a representative set of DNA and LINE transposable elements and used the obtained structural data to provide the first general structural characterization of TE proteins and to estimate the frequency of TE domestication and horizontal transfer events. We show that 1) ORF1 and Gag proteins of retrotransposons contain high amounts of structural disorder; thus, despite their very low conservation, the presence of disordered regions and probably their chaperone function is conserved. 2) The distribution of SCOP classes in DNA transposons and LINEs indicates that the proteins of DNA transposons are more ancient, containing folds that already existed when the first cellular organisms appeared. 3) DNA transposon proteins have lower contact order than randomly selected reference proteins, indicating rapid folding, most likely to avoid protein aggregation. 4) Structure-based searches for TE homologs indicate that the overall frequency of TE domestication events is low, whereas we found a relatively high number of cases where horizontal transfer, frequently involving parasites, is the most likely explanation for the observed homology. PMID:23530042

Determination of four different purines and their content change in seafood by high-performance liquid chromatography.

PubMed

Qu, Xin; Sui, Jianxin; Mi, Nasha; Lin, Hong

2017-01-01

Seafood is regarded as a high-purine food that may induce gout, which has attracted extensive attention concerning its safety. Therefore, the aim of this study was to develop a simple and reliable method to determine the purine content in seafood and its change during storage to offer consumers healthy diet information. Chromatographic separation was carried out using Waters Atlantis dC 18 column, and potassium phosphate monobasic solution (0.02 mol L -1 , pH 3.6) as a mobile phase. The average recovery yields of four purines were 91.5-105.0%, and relative standard deviation values were around 1.8-6.5%. Shrimp and snail contained higher amounts of purine than fish and bivalves; the livers and skins of fish contained higher amounts of purine than muscles; and the main purine varied depending on the type of seafood. Also, purine content of seafood changed during storage. The purine content of seafood differed depending on species, body part and degree of freshness, which could recommend consumers a healthy diet, especially for people with hyperuricemia and gout. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Molecular species composition of plant cardiolipin determined by liquid chromatography mass spectrometry

PubMed Central

Zhou, Yonghong; Peisker, Helga

2016-01-01

Cardiolipin (CL), an anionic phospholipid of the inner mitochondrial membrane, provides essential functions for stabilizing respiratory complexes and is involved in mitochondrial morphogenesis and programmed cell death in animals. The role of CL and its metabolism in plants are less well understood. The measurement of CL in plants, including its molecular species composition, is hampered by the fact that CL is of extremely low abundance, and that plants contain large amounts of interfering compounds including galactolipids, neutral lipids, and pigments. We used solid phase extraction by anion exchange chromatography to purify CL from crude plant lipid extracts. LC/MS was used to determine the content and molecular species composition of CL. Thus, up to 23 different molecular species of CL were detected in different plant species, including Arabidopsis, mung bean, spinach, barley, and tobacco. Similar to animals, plant CL is dominated by highly unsaturated species, mostly containing linoleic and linolenic acid. During phosphate deprivation or exposure to an extended dark period, the amount of CL decreased in Arabidopsis, accompanied with an increased degree in unsaturation. The mechanism of CL remodeling during stress, and the function of highly unsaturated CL molecular species, remains to be defined. PMID:27179363

Metal-silicate interaction in quenched shock-induced melt of the Tenham L6-chondrite

NASA Astrophysics Data System (ADS)

Leroux, Hugues; Doukhan, Jean-Claude; Guyot, François

2000-07-01

The metal-silicate microstructures in the shock-induced melt pockets of the Tenham (L6) chondrite have been investigated by analytical transmission electron microscopy. The melt areas, formed under high-pressure, high-temperature dynamic shock conditions, consist of spherical Fe-Ni metal/iron sulfide globules embedded in a silicate glass matrix, showing that the melt was quenched at high cooling rate. The Fe-Ni fraction in the globules is two-phase, composed of a bcc phase (˜5 wt% Ni) and an fcc phase (˜49 wt% Ni), indicating that fractional crystallisation of the metal occurred during the fast cooling. The metal fraction also contains appreciable amounts of non-siderophile elements (mostly Si, Mg and O) suggesting that these elements were trapped in the metal, either as alloying components or as tiny silicate or oxide inclusions. In the iron sulfide fraction, the Na content is high (>3 wt%), suggesting chalcophile behaviour for Na during the shock event. The composition of the silicate glass reflects non-equilibrium melting of several silicate phases (olivine, pyroxene and plagioclase). Moreover, the FeO content is high compared to the FeO contents of the unmelted silicates. Some Fe redistribution took place between metal and silicate liquids during the shock event. The silicate glass also contains tiny iron sulfide precipitates which most probably originated by exsolution during quench, suggesting that the molten silicate retained significant amounts of S, dissolved at high temperature and high pressure. Based on these observations, we suggest that non-equilibrium phenomena may be important in determining the compositions of metal and silicate reservoirs during their differentiation.

Significant Enrichment of Polyunsaturated Fatty Acids (PUFAs) in the Lipids Extracted by Supercritical CO2 from the Livers of Australian Rock Lobsters (Jasus edwardsii).

PubMed

Nguyen, Trung T; Zhang, Wei; Barber, Andrew R; Su, Peng; He, Shan

2015-05-13

Australian rock lobster (Jasus edwardsii) liver contains approximately 24.3% (w/w) lipids, which can contain a high amount of polyunsaturated fatty acids (PUFAs). However, this material has been found to be contaminated with arsenic (240 mg/kg) and cadmium (8 mg/kg). The high level of contaminants in the raw material and the large amount of PUFAs in the lipids prove a significant challenge in the extraction of high-quality lipids from this byproduct by conventional methods. Supercritical carbon dioxide (SC-CO2) extraction is a highly promising technology for lipid extraction with advantages including low contamination and low oxidation. The technique was optimized to achieve nearly 94% extraction of lipids relative to conventional Soxhlet extraction in Australian rock lobster liver at conditions of 35 MPa and 50 °C for 4 h. The extracted lipids are significantly enriched in PUFAs at 31.3% of total lipids, 4 times higher than those in the lipids recovered by Soxhlet extraction (7.8%). Specifically, the concentrations of docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) in SC-CO2 extraction are 7 times higher than those obtained by Soxhlet extraction. Moreover, very small amounts of toxic heavy metals such as lead (Pb), arsenic (As), mercury (Hg), and cadmium (Cd) were detected in the SC-CO2-extracted lipids, 0.5-27 times lower than those in the Soxhlet-extracted lipids, which are 40-200 times lower than the regulatory limit maximum values. The low levels of contaminants and the high proportion of PUFAs (dominated by DHA and EPA) found in the SC-CO2-extracted lipids from Australian rock lobster liver suggest that the material could potentially be used as a valuable source of essential fatty acids for human consumption.

The maximum water storage capacities in nominally anhydrous minerals in the mantle transition zone and lower mantle

NASA Astrophysics Data System (ADS)

Inoue, T.; Yurimoto, H.

2012-12-01

Water is the most important volatile component in the Earth, and affects the physicochemical properties of mantle minerals, e.g. density, elastic property, electrical conductivity, thermal conductivity, rheological property, melting temperature, melt composition, element partitioning, etc. So many high pressure experiments have been conducted so far to determine the effect of water on mantle minerals. To clarify the maximum water storage capacity in nominally anhydrous mantle minerals in the mantle transition zone and lower mantle is an important issue to discuss the possibility of the existence of water reservoir in the Earth mantle. So we have been clarifying the maximum water storage capacity in mantle minerals using MA-8 type (KAWAI-type) high pressure apparatus and SIMS (secondary ion mass spectroscopy). Upper mantle mineral, olivine can contain ~0.9 wt% H2O in the condition just above 410 km discontinuity in maximum (e.g. Chen et al., 2002; Smyth et al., 2006). On the other hand, mantle transition zone mineral, wadsleyite and ringwoodite can contain significant amount (about 2-3 wt.%) of H2O (e.g. Inoue et al., 1995, 1998, 2010; Kawamoto et al., 1996; Ohtani et al., 2000). But the lower mantle mineral, perovskite can not contain significant amount of H2O, less than ~0.1 wt% (e.g. Murakami et al., 2002; Inoue et al., 2010). In addition, garnet and stishovite also can not contain significant amount of H2O (e.g. Katayama et al., 2003; Mookherjee and Karato, 2010; Litasov et al., 2007). On the other hand, the water storage capacities of mantle minerals are supposed to be significantly coupled with Al by a substitution with Mg2+, Si4+ or Mg2+ + Si4+, because Al3+ is the trivalent cation, and H+ is the monovalent cation. To clarify the degree of the substitution, the water contents and the chemical compositions of Al-bearing minerals in the mantle transition zone and the lower mantle were also determined in the Al-bearing systems with H2O. We will introduce the recent results on the maximum water storage capacities in nominally anhydrous minerals in the mantle transition zone and lower mantle from the high pressure experimental point of view.

Uranyl peroxide enhanced nuclear fuel corrosion in seawater.

PubMed

Armstrong, Christopher R; Nyman, May; Shvareva, Tatiana; Sigmon, Ginger E; Burns, Peter C; Navrotsky, Alexandra

2012-02-07

The Fukushima-Daiichi nuclear accident brought together compromised irradiated fuel and large amounts of seawater in a high radiation field. Based on newly acquired thermochemical data for a series of uranyl peroxide compounds containing charge-balancing alkali cations, here we show that nanoscale cage clusters containing as many as 60 uranyl ions, bonded through peroxide and hydroxide bridges, are likely to form in solution or as precipitates under such conditions. These species will enhance the corrosion of the damaged fuel and, being thermodynamically stable and kinetically persistent in the absence of peroxide, they can potentially transport uranium over long distances.

High voltage capability electrical coils insulated with materials containing SF.sub.6 gas

DOEpatents

Lanoue, Thomas J.; Zeise, Clarence L.; Wagenaar, Loren; Westervelt, Dean C.

1988-01-01

A coil is made having a plurality of layers of adjacent metal conductor windings subject to voltage stress, where the windings have insulation therebetween containing a small number of minute disposed throughout its cross-section, where the voids are voids filled with SF.sub.6 gas to substitute for air or other gaseous materials in from about 60% to about 95% of the cross-sectional void volume in the insulation, thus incorporating an amount of SF.sub.6 gas in the cross-section of the insulation effective to substantially increase corona inception voltages.

Uranyl peroxide enhanced nuclear fuel corrosion in seawater

PubMed Central

Armstrong, Christopher R.; Nyman, May; Shvareva, Tatiana; Sigmon, Ginger E.; Burns, Peter C.; Navrotsky, Alexandra

2012-01-01

The Fukushima-Daiichi nuclear accident brought together compromised irradiated fuel and large amounts of seawater in a high radiation field. Based on newly acquired thermochemical data for a series of uranyl peroxide compounds containing charge-balancing alkali cations, here we show that nanoscale cage clusters containing as many as 60 uranyl ions, bonded through peroxide and hydroxide bridges, are likely to form in solution or as precipitates under such conditions. These species will enhance the corrosion of the damaged fuel and, being thermodynamically stable and kinetically persistent in the absence of peroxide, they can potentially transport uranium over long distances. PMID:22308442

Optimization of the Water Volume in the Buckets of Pico Hydro Overshot Waterwheel by Analytical Method

NASA Astrophysics Data System (ADS)

Budiarso; Adanta, Dendy; Warjito; Siswantara, A. I.; Saputra, Pradhana; Dianofitra, Reza

2018-03-01

Rapid economic and population growth in Indonesia lead to increased energy consumption, including electricity needs. Pico hydro is considered as the right solution because the cost of investment and operational cost are fairly low. Additionally, Indonesia has many remote areas with high hydro-energy potential. The overshot waterwheel is one of technology that is suitable to be applied in remote areas due to ease of operation and maintenance. This study attempts to optimize bucket dimensions with the available conditions. In addition, the optimization also has a good impact on the amount of generated power because all available energy is utilized maximally. Analytical method is used to evaluate the volume of water contained in bucket overshot waterwheel. In general, there are two stages performed. First, calculation of the volume of water contained in each active bucket is done. If the amount total of water contained is less than the available discharge in active bucket, recalculation at the width of the wheel is done. Second, calculation of the torque of each active bucket is done to determine the power output. As the result, the mechanical power generated from the waterwheel is 305 Watts with the efficiency value of 28%.

Lipid and carotenoid synthesis by Rhodosporidium diobovatum, grown on glucose versus glycerol, and its biodiesel properties.

PubMed

Nasirian, Nima; Mirzaie, Maryam; Cicek, Nazim; Levin, David B

2018-04-01

Relationships between lipid and carotenoid synthesis by Rhodosporidium diobovatum were investigated for cell cultures in nitrogen-limited medium (GMY) containing equimolar amounts of carbon of glucose or glycerol. The cultures were also supplemented with additional substrate at 120 h postinoculation (pi) and during a fed-batch experiment. Growth of R. diobovatum on glucose resulted in higher yields of triacyglycerides (TAGs) and carotenoid than when grown on glycerol, even though the cultures contained equimolar amounts of carbon. After the addition of fresh substrate at 120 h pi, total carotenoid concentrations were significantly different from the concentrations measured at 120 h pi in both glucose and glycerol cultures, with no concomitant increase in lipid concentrations, suggesting that carotenoid synthesis is linked to exponential-phase growth, while lipid synthesis is linked to stationary phase. We also compared the calculated properties of biodiesel that could be made with TAGs derived from R. diobovatum with properties of biodiesel made from TAGs of other oleaginous yeasts, microalgae, vegetable oils, and animal fats. This study shows that R. diobovatum can be an effective strain for production of neutral lipids containing high percentages of oleic acid, palmitic acid, and linoleic acid, as well as carotenoids.

Heterogeneity in friction strength of an active fault by incorporation of fragments of the surrounding host rock

NASA Astrophysics Data System (ADS)

Kato, Naoki; Hirono, Tetsuro

2016-07-01

To understand the correlation between the mesoscale structure and the frictional strength of an active fault, we performed a field investigation of the Atera fault at Tase, central Japan, and made laboratory-based determinations of its mineral assemblages and friction coefficients. The fault zone contains a light gray fault gouge, a brown fault gouge, and a black fault breccia. Samples of the two gouges contained large amounts of clay minerals such as smectite and had low friction coefficients of approximately 0.2-0.4 under the condition of 0.01 m s-1 slip velocity and 0.5-2.5 MP confining pressure, whereas the breccia contained large amounts of angular quartz and feldspar and had a friction coefficient of 0.7 under the same condition. Because the fault breccia closely resembles the granitic rock of the hangingwall in composition, texture, and friction coefficient, we interpret the breccia as having originated from this protolith. If the mechanical incorporation of wall rocks of high friction coefficient into fault zones is widespread at the mesoscale, it causes the heterogeneity in friction strength of fault zones and might contribute to the evolution of fault-zone architectures.

Luster measurements of lips treated with lipstick formulations.

PubMed

Yadav, Santosh; Issa, Nevine; Streuli, David; McMullen, Roger; Fares, Hani

2011-01-01

In this study, digital photography in combination with image analysis was used to measure the luster of several lipstick formulations containing varying amounts and types of polymers. A weighed amount of lipstick was applied to a mannequin's lips and the mannequin was illuminated by a uniform beam of a white light source. Digital images of the mannequin were captured with a high-resolution camera and the images were analyzed using image analysis software. Luster analysis was performed using Stamm (L(Stamm)) and Reich-Robbins (L(R-R)) luster parameters. Statistical analysis was performed on each luster parameter (L(Stamm) and L(R-R)), peak height, and peak width. Peak heights for lipstick formulation containing 11% and 5% VP/eicosene copolymer were statistically different from those of the control. The L(Stamm) and L(R-R) parameters for the treatment containing 11% VP/eicosene copolymer were statistically different from these of the control. Based on the results obtained in this study, we are able to determine whether a polymer is a good pigment dispersant and contributes to visually detected shine of a lipstick upon application. The methodology presented in this paper could serve as a tool for investigators to screen their ingredients for shine in lipstick formulations.

Antioxidant activity of rye bread enriched with milled buckwheat groats fractions.

PubMed

Żmijewski, Mirosław; Sokół-Łętowska, Anna; Pejcz, Ewa; Orzeł, Dagmara

2015-01-01

Buckwheat, despite its broad nutritional benefits, is still not widely appreciated grain. It contains a protein with preferred amino acid composition and it is a valuable source of micronutrients and vitamins of the B group and vitamin E. Moreover, buckwheat groats have a high amount of polyphenols, including flavonoids and flavones. Eating rye bread is beneficial due to its high content of dietary fiber, phenolic acids and characteristic taste and aroma. Therefore, the use of rye flour and buckwheat mill products for bread may allow obtaining a product of high nutritional value and flavor. The aim of the study was to evaluate the influence of buckwheat products addition and baking process on the antioxidant properties of rye-buckwheat blends and breads. Experimental material was rye flour type 580 and buckwheat flour, wholegrain flour and bran obtained by grinding buckwheat groats. Buckwheat products share was 20 and 35%. The control was the rye flour. In the rye-buckwheat blends and bread loaves, the contents of selected flavonoids by HPLC method, total polyphenols content by Folin-Ciocalteu method and the antioxidant activity by the DPPH˙ radical scavenging method were determined. Buckwheat bran was significantly richer in total polyphenols, rutin, quercetin, orientin and isoorientin than other buckwheat products and rye flour. Bread after baking contained similar amount of total polyphenols and quercetin and have a comparable ability to scavenge 1,1-diphenyl-2-picrylhydrazyl radicals (DPPH˙) than the corresponding blends. Baking process negatively affected the amount of rutin, orientin and isoorientin. The use of buckwheat bran as a replacement for wheat flour in bread significantly increases its nutritional value. The process of baking unequally affects the content of particular groups of antioxidant compounds.

Application of rotatable central composite design in the preparation and optimization of poly(lactic-co-glycolic acid) nanoparticles for controlled delivery of paclitaxel.

PubMed

Kollipara, Sivacharan; Bende, Girish; Movva, Snehalatha; Saha, Ranendra

2010-11-01

Polymeric carrier systems of paclitaxel (PCT) offer advantages over only available formulation Taxol® in terms of enhancing therapeutic efficacy and eliminating adverse effects. The objective of the present study was to prepare poly (lactic-co-glycolic acid) nanoparticles containing PCT using emulsion solvent evaporation technique. Critical factors involved in the processing method were identified and optimized by scientific, efficient rotatable central composite design aiming at low mean particle size and high entrapment efficiency. Twenty different experiments were designed and each formulation was evaluated for mean particle size and entrapment efficiency. The optimized formulation was evaluated for in vitro drug release, and absorption characteristics were studied using in situ rat intestinal permeability study. Amount of polymer and duration of ultrasonication were found to have significant effect on mean particle size and entrapment efficiency. First-order interactions of amount of miglyol with amount of polymer were significant in case of mean particle size, whereas second-order interactions of polymer were significant in mean particle size and entrapment efficiency. The developed quadratic model showed high correlation (R(2) > 0.85) between predicted response and studied factors. The optimized formulation had low mean particle size (231.68 nm) and high entrapment efficiency (95.18%) with 4.88% drug content. The optimized formulation showed controlled release of PCT for more than 72 hours. In situ absorption study showed faster and enhanced extent of absorption of PCT from nanoparticles compared to pure drug. The poly (lactic-co-glycolic acid) nanoparticles containing PCT may be of clinical importance in enhancing its oral bioavailability.

A moderate dose of red wine, but not de-alcoholized red wine increases coronary flow reserve.

PubMed

Kiviniemi, Tuomas O; Saraste, Antti; Toikka, Jyri O; Saraste, Markku; Raitakari, Olli T; Pärkkä, Jussi P; Lehtimäki, Terho; Hartiala, Jaakko J; Viikari, Jorma; Koskenvuo, Juha W

2007-12-01

Red wine consumption is associated with reduced cardiovascular disease mortality. Its cardioprotective properties may be partly related to its ability to improve endothelial function. The purpose of this randomized controlled cross-over study was to determine whether moderate doses of red wine and de-alcoholized red wine improve coronary flow velocity reserve (CFR). Using transthoracic Doppler echocardiography, 176 CFR measurements were made in 22 healthy men before and after ingestion of a moderate (4.0+/-0.4 dl) and an escalating high dose (total amount 8.1+/-0.9 dl) of alcohol-containing red wine and de-alcoholized red wine, which contained similar amounts of phenolic substances. The difference in plasma antioxidant capacity was determined by colorimetric assay kit. Red wine increased CFR from 3.8+/-1.4 to 4.5+/-1.4 (p<0.01) and 4.0+/-1.2 (p=NS) after moderate and high doses, respectively; whereas de-alcoholized red wine had no significant effects on CFR (4.0+/-0.7, 4.3+/-1.3 and 4.5+/-1.4, respectively). Plasma antioxidant capacity increased significantly after high dose of red wine (27.5+/-14.7%, p<0.001), but not after de-alcoholized red wine (0.5+/-10.5%, p=NS) despite similar amounts of phenolic substances. Differences between CFR and plasma antioxidant capacities before and after drinking had no significant association. A moderate dose of red wine, but not de-alcoholized red wine increases CFR. The increase of CFR is probably mediated by other than direct antioxidant properties of polyphenols, because the simultaneous increase of CFR and plasma antioxidant capacity were not associated.

Mechanosynthesis of A Ferritic ODS (Oxide Dispersion Strengthened) Steel Containing 14% Chromium and Its Characterization

NASA Astrophysics Data System (ADS)

Rivai, A. K.; Dimyati, A.; Adi, W. A.

2017-05-01

One of the advanced materials for application at high temperatures which is aggressively developed in the world is ODS (Oxide Dispersion strengthened) steel. ODS ferritic steels are one of the candidate materials for future nuclear reactors in the world (Generation IV reactors) because it is able to be used in the reactor above 600 °C. ODS ferritic steels have also been developed for the interconnect material of SOFC (Solid Oxide Fuel Cell) which will be exposed to about 800 °C of temperature. The steel is strengthened by dispersing homogeneously of oxide particles (ceramic) in nano-meter sized in the matrix of the steel. Synthesis of a ferritic ODS steel by dispersion of nano-particles of yttrium oxide (yttria: Y2O3) as the dispersion particles, and containing high-chromium i.e. 14% has been conducted. Synthesis of the ODS steels was done mechanically (mechanosynthesis) using HEM (High Energy ball Milling) technique for 40 and 100 hours. The resulted samples were characterized using SEM-EDS (Scanning Electron Microscope-Energy Dispersive Spectroscope), and XRD (X-ray diffraction) to analyze the microstructure characteristics. The results showed that the crystal grains of the sample with 100 hours milling time was much smaller than the sample with 40 hours milling time, and some amount of alloy was formed during the milling process even for 40 hours milling time. Furthermore, the structure analysis revealed that some amount of iron atom substituted by a slight amount of chromium atom as a solid solution. The quantitative analysis showed that the phase mostly consisted of FeCr solid-solution with the structure was BCC (body-centered cubic).

Inhalation of expiratory droplets in aircraft cabins.

PubMed

Gupta, J K; Lin, C-H; Chen, Q

2011-08-01

Airliner cabins have high occupant density and long exposure time, so the risk of airborne infection transmission could be high if one or more passengers are infected with an airborne infectious disease. The droplets exhaled by an infected passenger may contain infectious agents. This study developed a method to predict the amount of expiratory droplets inhaled by the passengers in an airliner cabin for any flight duration. The spatial and temporal distribution of expiratory droplets for the first 3 min after the exhalation from the index passenger was obtained using the computational fluid dynamics simulations. The perfectly mixed model was used for beyond 3 min after the exhalation. For multiple exhalations, the droplet concentration in a zone can be obtained by adding the droplet concentrations for all the exhalations until the current time with a time shift via the superposition method. These methods were used to determine the amount of droplets inhaled by the susceptible passengers over a 4-h flight under three common scenarios. The method, if coupled with information on the viability and the amount of infectious agent in the droplet, can aid in evaluating the infection risk. The distribution of the infectious agents contained in the expiratory droplets of an infected occupant in an indoor environment is transient and non-uniform. The risk of infection can thus vary with time and space. The investigations developed methods to predict the spatial and temporal distribution of expiratory droplets, and the inhalation of these droplets in an aircraft cabin. The methods can be used in other indoor environments to assess the relative risk of infection in different zones, and suitable measures to control the spread of infection can be adopted. Appropriate treatment can be implemented for the zone identified as high-risk zones. © 2011 John Wiley & Sons A/S.

Advanced Ultrasonic Measurement Methodology for Non-Invasive Interrogation and Identification of Fluids in Sealed Containers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tucker, Brian J.; Diaz, Aaron A.; Eckenrode, Brian A.

2006-03-16

The Hazardous Materials Response Unit (HMRU) and the Counterterrorism and Forensic Science Research Unit (CTFSRU), Laboratory Division, Federal Bureau of Investigation (FBI) have been mandated to develop and establish a wide range of unprecedented capabilities for providing scientific and technical forensic services to investigations involving hazardous chemical, biological, and radiological materials, including extremely dangerous chemical and biological warfare agents. Pacific Northwest National Laboratory (PNNL) has developed a portable, hand-held, hazardous materials acoustic inspection device (HAZAID) that provides noninvasive container interrogation and material identification capabilities using nondestructive ultrasonic velocity and attenuation measurements. Due to the wide variety of fluids as wellmore » as container sizes and materials, the need for high measurement sensitivity and advanced ultrasonic measurement techniques were identified. The HAZAID prototype was developed using a versatile electronics platform, advanced ultrasonic wave propagation methods, and advanced signal processing techniques. This paper primarily focuses on the ultrasonic measurement methods and signal processing techniques incorporated into the HAZAID prototype. High bandwidth ultrasonic transducers combined with the advanced pulse compression technique allowed researchers to 1) impart large amounts of energy, 2) obtain high signal-to-noise ratios, and 3) obtain accurate and consistent time-of-flight (TOF) measurements through a variety of highly attenuative containers and fluid media. Results of this feasibility study demonstrated that the HAZAID experimental measurement technique also provided information regarding container properties, which will be utilized in future container-independent measurements of hidden liquids.« less

High-Temperature Insulating Gap Filler

NASA Technical Reports Server (NTRS)

Toombs, Gordon R.; Oyoung, Kevin K.; Stevens, Everett G.

1991-01-01

New inorganic, ceramic filler for gaps between refractory ceramic tiles offers high resistance to heat and erosion. Consists of ceramic-fiber fabric precoated with silica and further coated with silica containing small amount of silicon carbide powder to increase thermal emittance. Developed as replacement for organic filler used on thermal-protection system of Space Shuttle. Promises to serve for many missions and to reduce cost and delay of refurbishing aerospace craft. Used as sealing material in furnaces or as heat shield for sensitive components in automobiles, aircraft, and home appliances.

Strength Characteristics of Resorbable Osteoconductive Ceramics Based on Diphosphates of Calcium and Alkali Metals

NASA Astrophysics Data System (ADS)

Putlayev, V. I.; Evdokimov, P. V.; Garshev, A. V.; Prosvirin, D. V.; Klimashina, E. S.; Safronova, T. V.; Ivanov, V. K.

2014-02-01

An investigation into the strength characteristics of ceramics based on diphosphates Ca(3- x)М2 x (PO4)2 ( x = 0-1 and М = Na, K) provides evidence of composition strengthening in the range х = 0.6-0.8 containing the greatest amount of the supercooled high-temperature modification α-СаМРО4. The method of high-temperature x-ray diffractometry is used to examine thermal expansion of rhenanite phases of СаМРО4.

High temperature sorbents for oxygen

NASA Technical Reports Server (NTRS)

Sharma, Pramod K. (Inventor)

1994-01-01

A sorbent capable of removing trace amounts of oxygen (ppt) from a gas stream at a high temperature above 200 C comprising a porous alumina silicate support, such as zeolite, containing from 1 to 10 percent by weight of ion exchanged transition metal, such as copper or cobalt ions, and 0.05 to 1.0 percent by weight of an activator selected from a platinum group metal such as platinum is described. The activation temperature, oxygen sorption, and reducibility are all improved by the presence of the platinum activator.

Method for preparing high purity vanadium

DOEpatents

Schmidt, Frederick; Carlson, O. Norman

1986-09-09

A method for preparing high purity vanadium having a low silicon content has been developed. Vanadium pentoxide is reduced with a stoichiometric, or slightly deficient amount of aluminum to produce a vanadium-aluminum alloy containing an excess of oxygen. Silicon is removed by electron-beam melting the alloy under oxidizing conditions to promote the formation of SiO which is volatile at elevated temperatures. Excess oxygen is removed by heating the alloy in the presence of calcium metal to form calcium oxide.

Method for preparing high purity vanadium

DOEpatents

Schmidt, F.; Carlson, O.N.

1984-05-16

A method for preparing high purity vanadium having a low silicon content has been developed. Vanadium pentoxide is reduced with a stoichiometric, or slightly deficient amount of aluminum to produce a vanadium-aluminum alloy containing an excess of oxygen. Silicon is removed by electron-beam melting the alloy under oxidizing conditions to promote the formation of SiO which is volatile at elevated temperatures. Excess oxygen is removed by heating the alloy in the presence of calcium metal to form calcium oxide.

48 CFR 970.5215-1 - Total available fee: Base fee amount and performance fee amount.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., Profit, and Other Incentives—Facility Management Contracts” if contained in the contract. (d) Performance... fee amount and performance fee amount. 970.5215-1 Section 970.5215-1 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY SUPPLEMENTARY REGULATIONS DOE MANAGEMENT AND OPERATING CONTRACTS...

Ethylenediamine-N,N′-Disuccinic Acid (EDDS)—Enhanced Flushing Optimization for Contaminated Agricultural Soil Remediation and Assessment of Prospective Cu and Zn Transport

PubMed Central

Ferraro, Alberto; Fabbricino, Massimiliano; La Marca, Agostino; Panico, Antonio; Spasiano, Danilo; Tognacchini, Alice; Pirozzi, Francesco

2018-01-01

This paper presents the results of an experimental study aimed at investigating the effect of operative parameters on the efficiency of a soil flushing process, conducted on real contaminated soil containing high amounts of Cu and Zn. Soil flushing tests were carried out with Ethylenediamine-N,N′-disuccinic acid (EDDS) as a flushing agent due to its high biodegradability and environmentally friendly characteristics. Process parameters such as Empty-Bed Contact Time (EBCT) and EDDS solution molarity were varied from 21–33 h and from 0.36–3.6 mM, respectively. Effects on the mobility of cations such as Fe and Mn were also investigated. Results showed that very high performances can be obtained at [EDDS] = 3.6 mM and EBCT = 33 h. In these conditions, in fact, the amount of removed Cu was 53%, and the amount of removed Zn was 46%. Metal distribution at different depths from the top surface revealed that Cu has higher mobility than Zn. The process results were strongly dependent on the exchange of metals due to the different stability constants of the EDDS complexes. Finally, results from a comparative study showed that soil washing treatment reached the same removal efficiency of the flushing process in a shorter time but required a larger amount of the EDDS solution. PMID:29562649

Ethylenediamine-N,N'-Disuccinic Acid (EDDS)-Enhanced Flushing Optimization for Contaminated Agricultural Soil Remediation and Assessment of Prospective Cu and Zn Transport.

PubMed

Race, Marco; Ferraro, Alberto; Fabbricino, Massimiliano; La Marca, Agostino; Panico, Antonio; Spasiano, Danilo; Tognacchini, Alice; Pirozzi, Francesco

2018-03-18

This paper presents the results of an experimental study aimed at investigating the effect of operative parameters on the efficiency of a soil flushing process, conducted on real contaminated soil containing high amounts of Cu and Zn. Soil flushing tests were carried out with Ethylenediamine- N , N '-disuccinic acid (EDDS) as a flushing agent due to its high biodegradability and environmentally friendly characteristics. Process parameters such as Empty-Bed Contact Time (EBCT) and EDDS solution molarity were varied from 21-33 h and from 0.36-3.6 mM, respectively. Effects on the mobility of cations such as Fe and Mn were also investigated. Results showed that very high performances can be obtained at [EDDS] = 3.6 mM and EBCT = 33 h. In these conditions, in fact, the amount of removed Cu was 53%, and the amount of removed Zn was 46%. Metal distribution at different depths from the top surface revealed that Cu has higher mobility than Zn. The process results were strongly dependent on the exchange of metals due to the different stability constants of the EDDS complexes. Finally, results from a comparative study showed that soil washing treatment reached the same removal efficiency of the flushing process in a shorter time but required a larger amount of the EDDS solution.

Production of highly tritiated water for tritium exposure studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muirhead, C.; Pilatzke, K.; Tripple, A.

2015-03-15

Tritium Facility staff at Chalk River Laboratories (CRL) have successfully prepared highly tritiated water for use in radiation resistance of PEM (Proton Exchange Membrane-based)electrolyser membrane. The goal of System A was to convert a known amount of elemental tritium (HT) into tritiated water vapour using a copper(II) oxide bed, and to condense the tritiated water vapour into a known amount of chilled heavy water (D{sub 2}O). The conversion and capture of tritium using this system is close to 100%. The goal of System B was to transfer tritiated water from the containment vessel to an exposure vessel (experiment) in amore » controlled and safe manner. System B is based on the pushing of D{sub 2}0 with low-pressure argon carrier gas to a calibrated volume and then to the exposure vessel. A method for delivering a known and controlled amount of tritiated water has been successfully demonstrated at CRL. Using both systems Tritium Facility staff have made and distributed highly tritiated water in a safe and controlled manner. This paper focuses on how the tritiated water was produced and dispensed to the experiment.« less

Nuclear fuel element

DOEpatents

Zocher, Roy W.

1991-01-01

A nuclear fuel element and a method of manufacturing the element. The fuel element is comprised of a metal primary container and a fuel pellet which is located inside it and which is often fragmented. The primary container is subjected to elevated pressure and temperature to deform the container such that the container conforms to the fuel pellet, that is, such that the container is in substantial contact with the surface of the pellet. This conformance eliminates clearances which permit rubbing together of fuel pellet fragments and rubbing of fuel pellet fragments against the container, thus reducing the amount of dust inside the fuel container and the amount of dust which may escape in the event of container breach. Also, as a result of the inventive method, fuel pellet fragments tend to adhere to one another to form a coherent non-fragmented mass; this reduces the tendency of a fragment to pierce the container in the event of impact.

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2001-01-01

A process for producing polycrystalline silicon carbide by heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

NASA Technical Reports Server (NTRS)

Barnard, Thomas Duncan (Inventor); Lipowitz, Jonathan (Inventor); Nguyen, Kimmai Thi (Inventor)

2000-01-01

A process for producing polycrystalline silicon carbide includes heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Estimation of yohimbine base in complex mixtures by quantitative HPTLC application.

PubMed

Adel-Kader, Maged Saad; Alwahebi, Naif Wahebi Hamadan; Alam, Prawez

2017-01-01

The indole alkaloid Yohimbine has been used for over two centuries in the treatment of erectly dysfunction. Several formulations containing yohimbine salts, yohimbe bark power or extract are marketed worldwide. Determination of the amount of yohimbine in such formulation is a challenging task due to their complex nature. Extraction followed by acid-base purification resulted in a relatively pure alkaloids containing fractions. The exact amounts of yohimbine free base in different formulations were determined by densitometric HPTLC validated methods using silica gel TLC plates. Standard curve for yohimbine was generated using yohimbine hydrochloride subjected to the same acid-base treatment as the used samples. All formulations found to contain yohimbine though some with less concentration than the labeled amount.

Biodegradation of indole at high concentration by persolvent fermentation with Pseudomonas sp. ST-200.

PubMed

Doukyu, N; Aono, R

1997-05-01

Pseudomonas sp. strain ST-200 grew on indole as a sole carbon source. The minimal inhibitory concentration of indole was 0.3 mg/ml for ST-200. However, ST-200 grew in a persolvent fermentation system containing a large amount of indole (a medium containing 20% by vol. diphenylmethane and 4 mg/ml indole), because most of the indole was partitioned in the organic solvent layer. When the organism was grown in the medium containing indole at 1 mg/ml in the presence of diphenylmethane, more than 98% of the indole was consumed after 48h. Isatic acid (0.4 mg/ml) and isatin (0.03 mg/ml) were produced as the metabolites in the aqueous medium layer.

Requirement of Phosphoinositides Containing Stearic Acid To Control Cell Polarity.

PubMed

Doignon, François; Laquel, Patricia; Testet, Eric; Tuphile, Karine; Fouillen, Laetitia; Bessoule, Jean-Jacques

2015-12-28

Phosphoinositides (PIPs) are present in very small amounts but are essential for cell signaling, morphogenesis, and polarity. By mass spectrometry, we demonstrated that some PIPs with stearic acyl chains were strongly disturbed in a psi1Δ Saccharomyces cerevisiae yeast strain deficient in the specific incorporation of a stearoyl chain at the sn-1 position of phosphatidylinositol. The absence of PIPs containing stearic acid induced disturbances in intracellular trafficking, although the total amount of PIPs was not diminished. Changes in PIPs also induced alterations in the budding pattern and defects in actin cytoskeleton organization (cables and patches). Moreover, when the PSI1 gene was impaired, a high proportion of cells with bipolar cortical actin patches that occurred concomitantly with the bipolar localization of Cdc42p was specifically found among diploid cells. This bipolar cortical actin phenotype, never previously described, was also detected in a bud9Δ/bud9Δ strain. Very interestingly, overexpression of PSI1 reversed this phenotype. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Changes of parameters during composting of bio-waste collected over four seasons.

PubMed

Hanc, Ales; Ochecova, Pavla; Vasak, Filip

2017-07-01

This study investigated the evolution of several main parameters during the composting of separately collected household bio-waste originating from urban settlements (U-bio-waste) and family houses (F-bio-waste) from four climate seasons. When comparing both types of composts, U-bio-waste compost contained a higher amount of nutrients, however F-bio-waste compost was characterized by greater yield, greater availability of phosphorus and magnesium, and faster stability. In terms of seasons, compost from bio-waste collected in spring contained the highest amount of nutrients, reflecting the high content of nutrients in plant feedstock. Dissolved organic carbon and pH in U- and F-bio-waste compost, respectively, frequently showed close relationships with other parameters. The seasonal variations of most of the parameters in the composts were found to be lower compared to the variations observed in the feedstocks. The greatest seasonal variation was found in nitrate nitrogen, which is the reason for the more frequent analysis of this parameter.

Development of a novel microbial sensor with baker's yeast cells for monitoring temperature control during cold food chain.

PubMed

Kogure, H; Kawasaki, S; Nakajima, K; Sakai, N; Futase, K; Inatsu, Y; Bari, M L; Isshiki, K; Kawamoto, S

2005-01-01

A novel microbial sensor containing a commercial baker's yeast with a high freeze tolerance was developed for visibly detecting inappropriate temperature control of food. When the yeast cells fermented glucose, the resulting gas production triggered the microbial sensor. The biosensor was a simple, small bag containing a solution of yeast cells, yeast extract, glucose, and glycerol sealed up with multilayer transparent film with barriers against oxygen and humidity. Fine adjustment of gas productivity in the biosensor at low temperatures was achieved by changing either or both concentrations of glucose and yeast cells. Moreover, the amount of time that food was exposed to inappropriate temperatures could be deduced by the amount of gas produced in the biosensor. The biosensor was stable without any functional loss for up to 1 week in frozen storage. The biosensor could offer a useful tool for securing food safety by maintaining low-temperature control in every stage from farm to fork, including during transportation, in the store, and at home.

Biochemical and technological studies on the production of isolated guar protein.

PubMed

Khalil, M M

2001-02-01

Guar seeds contain 32% crude protein. Therefore, attempts were made to prepare protein isolates from guar seed flour (GSF) by extraction in different media (distilled water, salt solution, alkali solution alone or in combination) followed by a precipitation at acid pH. From the four technologies adopted, mixed salt-alkali solution was found to be the most satisfactory for extraction of protein from GSF. The highest amount of product was obtained in the mixed technology along with the highest amount of protein (87.5%). Protein isolates were also nutritionally evaluated following well-established rat bioassay procedures in a comparative study with casein as standard. The protein isolates are rich in lysine but poor in sulphur-containing amino acids such as methionine and cysteine. Protein isolates obtained by mixed salt-alkali solution showed high water and oil absorption as well as good emulsifying and foaming stability. The results indicate that protein isolates can be used as a supplementary source of protein in different food industries.

An interface for the direct coupling of small liquid samples to AMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ognibene, T. J.; Thomas, A. T.; Daley, P. F.

We describe the moving wire interface attached to the 1-MV AMS system at LLNL’s Center for Accelerator Mass Spectrometry for the analysis of nonvolatile liquid samples as either discrete drops or from the direct output of biochemical separatory instrumentation, such as high-performance liquid chromatography (HPLC). Discrete samples containing at least a few 10 s of nanograms of carbon and as little as 50 zmol 14C can be measured with a 3–5% precision in a few minutes. The dynamic range of our system spans approximately 3 orders in magnitude. Sample to sample memory is minimized by the use of fresh targetsmore » for each discrete sample or by minimizing the amount of carbon present in a peak generated by an HPLC containing a significant amount of 14C. As a result, liquid sample AMS provides a new technology to expand our biomedical AMS program by enabling the capability to measure low-level biochemicals in extremely small samples that would otherwise be inaccessible.« less

An interface for the direct coupling of small liquid samples to AMS

DOE PAGES

Ognibene, T. J.; Thomas, A. T.; Daley, P. F.; ...

2015-05-28

We describe the moving wire interface attached to the 1-MV AMS system at LLNL’s Center for Accelerator Mass Spectrometry for the analysis of nonvolatile liquid samples as either discrete drops or from the direct output of biochemical separatory instrumentation, such as high-performance liquid chromatography (HPLC). Discrete samples containing at least a few 10 s of nanograms of carbon and as little as 50 zmol 14C can be measured with a 3–5% precision in a few minutes. The dynamic range of our system spans approximately 3 orders in magnitude. Sample to sample memory is minimized by the use of fresh targetsmore » for each discrete sample or by minimizing the amount of carbon present in a peak generated by an HPLC containing a significant amount of 14C. As a result, liquid sample AMS provides a new technology to expand our biomedical AMS program by enabling the capability to measure low-level biochemicals in extremely small samples that would otherwise be inaccessible.« less

Converting citrus wastes into value-added products: Economic and environmently friendly approaches.

PubMed

Sharma, Kavita; Mahato, Neelima; Cho, Moo Hwan; Lee, Yong Rok

2017-02-01

Citrus fruits, including oranges, grapefruits, lemons, limes, tangerines, and mandarins, are among the most widely cultivated fruits around the globe. Its production is increasing every year due to rising consumer demand. Citrus-processing industries generate huge amounts of wastes every year, and citrus peel waste alone accounts for almost 50% of the wet fruit mass. Citrus waste is of immense economic value as it contains an abundance of various flavonoids, carotenoids, dietary fiber, sugars, polyphenols, essential oils, and ascorbic acid, as well as considerable amounts of some trace elements. Citrus waste also contains high levels of sugars suitable for fermentation for bioethanol production. However, compounds such as D-limonene must be removed for efficient bioethanol production. The aim of the present article was to review the latest advances in various popular methods of extraction for obtaining value-added products from citrus waste/byproducts and their potential utility as a source of various functional compounds. Copyright © 2016 Elsevier Inc. All rights reserved.

Phenolic profile and effect of growing area on Pistacia lentiscus seed oil.

PubMed

Mezni, Faten; Slama, Awatef; Ksouri, Riadh; Hamdaoui, Ghaith; Khouja, Mohamed Larbi; Khaldi, Abdelhamid

2018-08-15

In this investigation, we aimed to study, for the first time, the phenolic composition of Pistacia lentiscus seed oils from different growing areas. Extraction of the phenolic fraction from oils was done by methanol/water. Phenolic profiles were determined using chromatographic analysis by High Performance Liquid Chromatography (HPLC-DAD/MSD) and its quantification was done using an internal standard which is unidentified in the studied oil (syringic acid). Forty phenolic compounds were quantified and only eighteen of them were identified. The eight studied oils showed different phenolic profiles. The total phenols amount varied from 538.03 mg/kg oil in Jbel Masour oils to 4260.57 mg/kg oil in oils from Kef Erraai. The highest amount of secoiridoids was reached by Bouchoucha oil containing 366.71 mg/kg oil of Oleuropein aglycon. Oils from Kef Erraai locality contained the highest concentrations in flavonols (377.44 mg/kg oil) and in phenolic acids (2762.67 mg/kg oil). Copyright © 2018 Elsevier Ltd. All rights reserved.

Selective etching of TiN over TaN and vice versa in chlorine-containing plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Hyungjoo; Zhu Weiye; Liu Lei

2013-05-15

Selectivity of etching between physical vapor-deposited TiN and TaN was studied in chlorine-containing plasmas, under isotropic etching conditions. Etching rates for blanket films were measured in-situ using optical emission of the N{sub 2} (C{sup 3}{Pi}{sub u}{yields}B{sup 3}{Pi}{sub g}) bandhead at 337 nm to determine the etching time, and transmission electron microscopy to determine the starting film thickness. The etching selectivity in Cl{sub 2}/He or HCl/He plasmas was poor (<2:1). There was a window of very high selectivity of etching TiN over TaN by adding small amounts (<1%) of O{sub 2} in the Cl{sub 2}/He plasma. Reverse selectivity (10:1 of TaNmore » etching over TiN) was observed when adding small amounts of O{sub 2} to the HCl/He plasma. Results are explained on the basis of the volatility of plausible reaction products.« less

Calcium Chloride in Neonatal Parenteral Nutrition Solutions with and without Added Cysteine: Compatibility Studies Using Laser and Micro-Flow Imaging Methodology.

PubMed

Huston, Robert K; Christensen, J Mark; Alshahrani, Sultan M; Mohamed, Sumeia M; Clark, Sara M; Nason, Jeffrey A; Wu, Ying Xing

2015-01-01

Previous studies of compatibility of calcium chloride (CaCl2) and phosphates have not included particle counts in the range specified by the United States Pharmacopeia. Micro-flow imaging techniques have been shown to be comparable to light obscuration when determining particle count and size in pharmaceutical solutions. The purpose of this study was to do compatibility testing for parenteral nutrition (PN) solutions containing CaCl2 using dynamic light scattering and micro-flow imaging techniques. Solutions containing TrophAmine (Braun Medical Inc, Irvine, CA), CaCl2, and sodium phosphate (NaPhos) were compounded with and without cysteine. All solutions contained standard additives to neonatal PN solutions including dextrose, trace metals, and electrolytes. Control solutions contained no calcium or phosphate. Solutions were analyzed for particle size and particle count. Means of Z-average particle size and particle counts of controls were determined. Study solutions were compared to controls and United States Pharmacopeia (USP) Chapter 788 guidelines. The maximum amount of Phos that was compatible in solutions that contained at least 10 mmol/L of Ca in 2.5% amino acids (AA) was determined. Compatibility of these solutions was verified by performing analyses of 5 repeats of these solutions. Microscopic analyses of the repeats were also performed. Amounts of CaCl2 and NaPhos that were compatible in solutions containing 1.5%, 2%, 2.5%, and 3% AA were determined. The maximum amount of NaPhos that could be added to TrophAmine solutions of > = 2.5% AA containing at least 10 mmol/L of CaCl2 was 7.5 mmol/L. Adding 50 mg/dL of cysteine increased the amount of NaPhos that could be added to solutions containing 10 mmol/L of CaCl2 to 10 mmol/L. Calcium chloride can be added to neonatal PN solutions containing NaPhos in concentrations that can potentially provide an intravenous intake of adequate amounts of calcium and phosphorus.

Oil residue contamination of continental shelf sediments of the Gulf of Mexico.

PubMed

Harding, V; Camp, J; Morgan, L J; Gryko, J

2016-12-15

We have investigated the distribution of a heavy oil residue in the coastal sediments of the Gulf of Mexico. The amount of the contamination was determined by high-temperature pyrolysis coupled with the Gas Chromatography-Mass Spectrometry (GCMS) of air-dried sediments. The pyrolysis products contain straight-chain saturated and unsaturated hydrocarbons, such as dodecane and 1-dodecene, resulting in a very characteristic pattern of double peaks in the GCMS. Hydrocarbons containing 8 to 23 carbon atoms were detected in the pyrolysis products. Using thermal pyrolysis we have found that the sediment samples collected along Texas, Louisiana, and Mississippi shores contain no detectable traces of oil residue, but most of the samples collected along Alabama and Florida shores contain ~200ppm of heavy oil residue. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laser confocal microscope for analysis of 3013 inner container closure weld region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez-Rodriguez, M. J.

As part of the protocol to investigate the corrosion in the inner container closure weld region (ICCWR) a laser confocal microscope (LCM) was used to perform close visual examination of the surface and measurements of corrosion features on the surface. However, initial analysis of selected destructively evaluated (DE) containers using the LCM revealed several challenges for acquiring, processing and interpreting the data. These challenges include topography of the ICCWR sample, surface features, and the amount of surface area for collecting data at high magnification conditions. In FY17, the LCM parameters were investigated to identify the appropriate parameter values for datamore » acquisition and identification of regions of interest. Using these parameter values, selected DE containers were analyzed to determine the extent of the ICCWR to be examined.« less

Self-consolidating concretes containing waste PET bottles as sand replacement

NASA Astrophysics Data System (ADS)

Khalid, Faisal Sheikh; Azmi, Nurul Bazilah; Mazenan, Puteri Natasya; Shahidan, Shahiron; Othman, Nor hazurina; Guntor, Nickholas Anting Anak

2018-02-01

This study evaluates the effect of self-consolidating concrete (SCC) containing waste polyethylene terephthalate (PET) granules on the fresh, mechanical and water absorption properties. Fine aggregates were replaced from 0% to 8% by PET granules. The fresh properties of SCC containing PET granules were determined using slump flow and V-funnel flow time tests. The compressive and splitting tensile strength were evaluated. The results indicated that utilization of waste PET granules in production of SCC could be an effective way for recycling purpose. The maximum amount of PET replacement should be limited to 5%. Exceeding 5% of PET content may result in an increase of V-funnel flow time to overpass the limiting value, decrease in strength. The production of high performance SCC containing 5% PET granules satisfies all the requirements for SCC with satisfactory outputs.

Meta-analysis: Does garlic intake reduce risk of gastric cancer?

PubMed

Kodali, R T; Eslick, Guy D

2015-01-01

In the past 2 decades, various epidemiological studies investigated whether garlic can positively modify the risk of gastric cancer. Garlic contains numerous sulfide compounds, including diallyl trisulfide, which have anticarcinogenic properties. We conducted a meta-analysis to determine if garlic intake reduces the risk of gastric cancer. An electronic search of MEDLINE, PubMed, and EMBASE to June 2014 was completed. There were 14 case control studies, 2 randomized controlled studies, and 1 cohort study that fulfilled our inclusion criteria. We used a random effects model to calculate pooled odds ratios (OR) and 95% confidence intervals (CIs) for risk of gastric cancer with garlic consumption. Meta-analysis of a total of 8,621 cases and 14,889 controls was conducted. Significant variability in duration of garlic intake and reference categories for amount of intake was noted. High, low, and any garlic intake were all associated with reduced risk of gastric cancer. High intake had the most significant risk reduction, OR = 0.49 (95% CI: 0.38-0.62). Heterogeneity was low (I² = 30.85, P = 0.17). A more modest risk reduction was associated with low intake, OR = 0.75 (95% CI: 0.58-0.97). Half of the studies did not separate garlic intake into high or low amounts, intake was only noted as consumption vs. non-consumption. Any amount of consumption still showed a risk reduction similar to low intake, OR = 0.77 (95% CI: 0.60-1.00). Low and any amount of consumption showed moderate heterogeneity (58% and 45%, respectively). Garlic intake appears to be associated with reduced risk of gastric cancer. Further high quality studies are required to confirm this finding and to assess the amount of garlic that needs to be consumed for protective effect.

Novel Method for High-Throughput Full-Length IGHV-D-J Sequencing of the Immune Repertoire from Bulk B-Cells with Single-Cell Resolution.

PubMed

Vergani, Stefano; Korsunsky, Ilya; Mazzarello, Andrea Nicola; Ferrer, Gerardo; Chiorazzi, Nicholas; Bagnara, Davide

2017-01-01

Efficient and accurate high-throughput DNA sequencing of the adaptive immune receptor repertoire (AIRR) is necessary to study immune diversity in healthy subjects and disease-related conditions. The high complexity and diversity of the AIRR coupled with the limited amount of starting material, which can compromise identification of the full biological diversity makes such sequencing particularly challenging. AIRR sequencing protocols often fail to fully capture the sampled AIRR diversity, especially for samples containing restricted numbers of B lymphocytes. Here, we describe a library preparation method for immunoglobulin sequencing that results in an exhaustive full-length repertoire where virtually every sampled B-cell is sequenced. This maximizes the likelihood of identifying and quantifying the entire IGHV-D-J repertoire of a sample, including the detection of rearrangements present in only one cell in the starting population. The methodology establishes the importance of circumventing genetic material dilution in the preamplification phases and incorporates the use of certain described concepts: (1) balancing the starting material amount and depth of sequencing, (2) avoiding IGHV gene-specific amplification, and (3) using Unique Molecular Identifier. Together, this methodology is highly efficient, in particular for detecting rare rearrangements in the sampled population and when only a limited amount of starting material is available.

Caffeine Content in Popular Energy Drinks and Energy Shots.

PubMed

Attipoe, Selasi; Leggit, Jeffrey; Deuster, Patricia A

2016-09-01

The use of energy beverages is high among the general population and military personnel. Previous studies have reported discrepancies between the actual amount of caffeine in products and the amount of caffeine on stated labels. Thus, the purpose of this study was to examine the content of caffeine listed on the labels of various energy drinks and energy shots. Top-selling energy drinks (n = 9) and energy shots (n = 5) were purchased from retail stores. Three of each of the 14 products were purchased and analyzed for caffeine content by an independent laboratory. Of the 14 products tested, 5 did not provide caffeine amounts on their facts panel-of those, 3 listed caffeine as an ingredient and 2 listed caffeine as part of a proprietary blend. The remaining 9 (of 14) products stated the amounts of caffeine on their labels, all of which were within 15% of the amount indicated on the label. In this study, although the energy beverages that indicated the amount of caffeine it contained had values within ±15% of the amount listed on the label, a potentially acceptable range, this finding is not acceptable with regard to current labeling regulations, which require added ingredients to total 100%. Reprint & Copyright © 2016 Association of Military Surgeons of the U.S.

Estimates of Ethanol Exposure in Children from Food not Labeled as Alcohol-Containing.

PubMed

Gorgus, Eva; Hittinger, Maike; Schrenk, Dieter

2016-09-01

Ethanol is widely used in herbal medicines, e.g., for children. Furthermore, alcohol is a constituent of fermented food such as bread or yogurt and "non-fermented" food such as fruit juices. At the same time, exposure to very low levels of ethanol in children is discussed as possibly having adverse effects on psychomotoric functions. Here, we have analyzed alcohol levels in different food products from the German market. It was found that orange, apple and grape juice contain substantial amounts of ethanol (up to 0.77 g/L). Furthermore, certain packed bakery products such as burger rolls or sweet milk rolls contained more than 1.2 g ethanol/100 g. We designed a scenario for average ethanol exposure by a 6-year-old child. Consumption data for the "categories" bananas, bread and bakery products and apple juice were derived from US and German surveys. An average daily exposure of 10.3 mg ethanol/kg body weight (b.w.) was estimated. If a high (acute) consumption level was assumed for one of the "categories," exposure rose to 12.5-23.3 mg/kg b.w. This amount is almost 2-fold (average) or up to 4-fold (high) higher than the lowest exposure from herbal medicines (6 mg/kg b.w.) suggested to require warning hints for the use in children. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Efficacy and toxicity of formalin solutions containing paraformaldehyde for fish and egg treatments

USGS Publications Warehouse

Howe, G.E.; Marking, L.L.; Bills, T.D.; Schreier, Theresa M.

1995-01-01

Formalin used for fish and egg treatments at hatcheries often develops a white precipitate called paraformaldehyde when stored at low temperatures. This presents a problem for hatchery managers because most of the literature and treatment procedures claim that formalin containing paraformaldehyde is more toxic than pure formalin and is not safe for fish or egg treatments. Acute toxicity tests with rainbow trout (Oncorhynchus mykiss) and channel catfish (Ictalurus punctatus) showed that the toxicity of formalin solutions containing a moderate amount of fine paraformaldehyde was similar to that of pure formalin. In efficacy tests on fish eggs, the bottom fraction of a formalin solution containing paraformaldehyde and a sample from the clear top fraction were equally effective in controlling fungal infection on rainbow trout eggs and caused no treatment-related mortality. Chemical assays found on average a 3% difference in formaldehyde concentration between top and bottom fractions of a formalin solution containing paraformaldehyde. We recommend normal use of formalin solutions containing light to moderate amounts of fine paraformaldehyde. Allowing solutions to warm to room temperature may resolubilize moderate amounts of paraformaldehyde if the exposure to cold was not prolonged. If precipitation is heavier, clear top fractions can be decanted and used as normal because paraformaldehyde settles to the bottom of containers. Formalin solutions that have been exposed to freezing temperatures for long periods (more than 6 weeks) and have developed large amounts of paraformaldehyde solids should not be used and resolubilization by warming is not possible. Formation of paraformaldehyde in formalin solutions can be easily avoided by storing formalin at room temperature.

Complement activating properties of complexes containing rheumatoid factor in synovial fluids and sera from patients with rheumatoid arthritis.

PubMed Central

Elson, C J; Carter, S D; Cottrell, B J; Scott, D G; Bacon, P A; Wallington, T B

1985-01-01

The relationship between complexes containing rheumatoid factor and complexes activating complement was examined in synovial fluids and sera from patients with rheumatoid arthritis (RA). In each case this was performed by quantifying the amount of rheumatoid factor bound by solid phase Fab'2 anti-C3 and/or solid phase conglutinin. Both anti-C3 coated and conglutinin coated microtitre plates bound high levels of complexes containing rheumatoid factor from sera of RA patients with vasculitis. Unexpectedly, these complexes were detected in synovial fluids from only a minority of RA patients with synovitis. However, RA synovial fluids did contain other complexes as shown by the presence of complement consuming activity, C1q binding material and immunoglobulin attaching to conglutinin. It is considered that in RA synovial fluids the complexes containing RF and those activating complement are not necessarily the same whilst in vasculitic sera the complexes containing rheumatoid factor also activate complement. PMID:3978872

A Panel Analysis of Student Mathematics Achievement in the US in the 1990s: Does Increasing the Amount of Time in Learning Activities Affect Math Achievement?

ERIC Educational Resources Information Center

Aksoy, Tevfik; Link, Charles R.

2000-01-01

Uses panel estimation techniques to estimate econometric models of mathematics achievement determinants for a nationally representative sample of high-school students. Extra time spent on math homework increases test scores; an extra hour of TV viewing negatively affects scores. Longer math periods also help. (Contains 56 references.) (MLH)

Advances in corrosion testing of metals in contact with treated wood

Treesearch

Samuel Zelinka; D.S. Stone

2010-01-01

A January 2004 change in the regulation of wood preservatives used in the U.S.has increased the use of newer wood preservatives, such as alkaline copper quaternary (ACQ) and copper azole (CuAz). These preservatives contain high amounts of cupric ions, which may be reduced to copper metal at the expense of less noble steel and galvanized fasteners in the wood....

METAL COATING BATHS

DOEpatents

Robinson, J.W.

1958-08-26

A method is presented for restoring the effectiveness of bronze coating baths used for hot dip coating of uranium. Such baths, containing a high proportion of copper, lose their ability to wet uranium surfaces after a period of use. The ability of such a bath to wet uranium can be restored by adding a small amount of metallic aluminum to the bath, and skimming the resultant hard alloy from the surface.

Circumpolar assessment of permafrost C quality and its vulnerability over time using long-term incubation data

Treesearch

C. Schädel; E.A.G. Schuur; R. Bracho; B. Elberling; C. Knoblauch; H. Lee; Y. Luo; G. Shaver; M. Turetsky.

2014-01-01

High-latitude ecosystems store approximately 1700 Pg of soil carbon (C), which is twice as much C as is currently contained in the atmosphere. Permafrost thaw and subsequent microbial decomposition of permafrost organic matter could add large amounts of C to the atmosphere, thereby influencing the global C cycle. The rates at which C is being released from the...

Short chain nitrocompounds as a treatment of layer hen manure and litter; effects on in vitro survivability of Salmonella, generic E. coli, and nitrogen metabolism

USDA-ARS?s Scientific Manuscript database

Layer hen manure and litter contain appreciable amounts of uric acid, which makes these good crude protein sources for ruminants. Rumen microbial populations can upgrade the nitrogen in uric acid into high quality microbial protein of nutritional value to the host. Layer hen manure and litter can ...

Plasma levels of selenium-containing proteins in Inuit adults from Nunavik.

PubMed

Achouba, Adel; Dumas, Pierre; Ouellet, Nathalie; Lemire, Mélanie; Ayotte, Pierre

2016-11-01

Selenium (Se) is highly abundant in marine foods traditionally consumed by Inuit of Nunavik (Northern Quebec, Canada) and accordingly, their Se intake is among the highest in the world. However, little is known regarding the biological implications of this high Se status in this Arctic indigenous population. We used a method combining affinity chromatography and inductively coupled plasma-mass spectrometry with quantification by post-column isotope dilution to determine total Se levels and concentrations of Se-containing proteins in archived plasma samples of Inuit adults who participated to the 2004 Nunavik Inuit Health Survey (N = 852). Amounts of mercury (Hg) associated with Se-containing proteins were also quantified. Results show that glutathione peroxidase 3 (GPx3), selenoprotein P (SelP) and selenoalbumin (SeAlb) represented respectively 25%, 52% and 23% of total plasma Se concentrations. In addition, small amounts of Hg co-eluted with each Se-containing protein and up to 50% of plasma Hg was associated to SelP. Total plasma Se concentrations (median = 139 μg L− 1; interquartile range (IQR) = 22.7 μg L− 1) were markedly lower and less variable than whole blood Se concentration (median = 261 μg L− 1, IQR = 166 μg L− 1). A non linear relation was observed between whole blood Se and plasma Se levels, with plasma Se concentrations leveling off at approximately 200 μg L− 1, whereas 16% and 3% of individuals exhibited whole blood concentrations higher than 500 μg L− 1 and 1000 μg L− 1, respectively. In contrast, a linear relationship was previously reported in communities consuming Brazil nuts which are rich Se, mainly present as selenomethionine. This suggests that a different selenocompound, possibly selenoneine, is present in the Arctic marine food chain and accumulates in the blood cellular fraction of Inuit.

Assessment of hydrocarbon source rock potential of Polish bituminous coals and carbonaceous shales

USGS Publications Warehouse

Kotarba, M.J.; Clayton, J.L.; Rice, D.D.; Wagner, M.

2002-01-01

We analyzed 40 coal samples and 45 carbonaceous shale samples of varying thermal maturity (vitrinite reflectance 0.59% to 4.28%) from the Upper Carboniferous coal-bearing strata of the Upper Silesian, Lower Silesian, and Lublin basins, Poland, to evaluate their potential for generation and expulsion of gaseous and liquid hydrocarbons. We evaluated source rock potential based on Rock-Eval pyrolysis yield, elemental composition (atomic H/C and O/C), and solvent extraction yields of bitumen. An attempt was made to relate maceral composition to these source rock parameters and to composition of the organic matter and likely biological precursors. A few carbonaceous shale samples contain sufficient generation potential (pyrolysis assay and elemental composition) to be considered potential source rocks, although the extractable hydrocarbon and bitumen yields are lower than those reported in previous studies for effective Type III source rocks. Most samples analysed contain insufficient capacity for generation of hydrocarbons to reach thresholds required for expulsion (primary migration) to occur. In view of these findings, it is improbable that any of the coals or carbonaceous shales at the sites sampled in our study would be capable of expelling commercial amounts of oil. Inasmuch as a few samples contained sufficient generation capacity to be considered potential source rocks, it is possible that some locations or stratigraphic zones within the coals and shales could have favourable potential, but could not be clearly delimited with the number of samples analysed in our study. Because of their high heteroatomic content and high amount of asphaltenes, the bitumens contained in the coals are less capable of generating hydrocarbons even under optimal thermal conditions than their counterpart bitumens in the shales which have a lower heteroatomic content. Published by Elsevier Science B.V.

Colour and label evaluation of commercial pasteurised red juices and related drinks.

PubMed

Fallico, B; Arena, E; Chiappara, E; Ballistreri, G

2010-01-01

Despite growing demand by consumers for healthy beverages, artificial colours are still widely used. Levels of anthocyanins and artificial colours were determined by HPLC with UV-Vis detection in red orange juices and other red beverages (nectar, juice-based, health, carbonated and sports drinks). The contribution of pigments to the visible colour of the beverage was calculated. Red orange juice samples contained about 34 mg l(-1) of anthocyanins, which were responsible for about 92% of the visible colour. Red juice-based drinks, containing from 0% to 30% of red orange, berry, grape or pomegranate juices, had low levels of anthocyanins (about 7 mg l(-1)) and high levels of E129 (about 32 mg l(-1)), which were responsible for about 90.7% of the colour of these beverages. Red health drinks, enriched with vitamins and polyphenols, contained from 3% to 50% of red fruit juices. Also in this case the E129 levels were higher (about 22 mg l(-1)) than anthocyanins (about 9 mg l(-1)), and were responsible for the colour of the beverages (76.1%). High levels of artificial colours were found in red orange carbonated drinks, but in comparable amounts with those found in the other beverage samples, while anthocyanins were only present in trace amounts. Although all of the beverages claimed to contain red fruits on the labels, no correlation was found between the level of anthocyanins and the declared percentage of red fruits. These labels generally conformed with the requirements of the law, but food product labels can often be misleading to consumers about the real characteristics of the product.

Genotoxicity of mercury used in chromosome aberration tests.

PubMed

Akiyama, M; Oshima, H; Nakamura, M

2001-01-01

The purpose of this study was to investigate the genotoxic effects of Hg released from dental amalgams. The chromosome aberration test was conducted using original extracts and their diluted solutions of conventional type amalgam and high copper amalgam. The concentrations of Hg, Cu and Ag in the original extract of high copper amalgam were 17.64, 7.97 and 43.90 microM, respectively. Those in the original extract of conventional type amalgam were 20.63, 7.87 and 14.79 microM, respectively. 10 and 30 microM Hg(2+) were also used for comparison. The frequency of chromosome aberrations was below 5% with 0 microM Hg(2+) and with a triple dilution of high copper amalgam extract, containing 5.88 microM Hg, 14.63 microM Cu and 2.65 microM Ag. However, 9.5% of the cells showed chromosome aberrations with a quadruple dilution of conventional type amalgam, containing 5.15 microM Hg, 3.69 microM Cu and 1.96 microM Ag. The amount of Hg in the quadruple dilution of conventional type amalgam was less than that in the triple dilution of high copper amalgam extract and 10 microM Hg(2+). A concentration of 30 microM Hg(2+) caused 34.5% of the cells to show chromosome aberrations while with a two-thirds dilution of high copper amalgam extract, containing 11.76 microM Hg, 29.26 microM Cu and 5.31 microM Ag, 58.5% of the cells showed chromosome aberrations. A two-thirds dilution of high copper amalgam extract induced more chromosome aberrations than 30 microM Hg(2+), although the amount of Hg was less than 30 microM Hg(2+). A triple dilution of conventional type amalgam extract, original extracts of conventional type amalgam and high copper amalgam and 100 microM Hg(2+) were induced few metaphases. It was revealed that the conventional type amalgam induced chromosome aberrations with quadruple dilution where cell viability was about 80% and that the high copper amalgam induced a high level of chromosome aberrations with the two-thirds dilution. The effects of low level Hg on humans are not clear.

29 CFR 4.142 - Contracts in an indefinite amount.

Code of Federal Regulations, 2010 CFR

2010-07-01

... McNamara-O'Hara Service Contract Act Determining Amount of Contract § 4.142 Contracts in an indefinite amount. (a) Every contract subject to this Act which is indefinite in amount is required to contain the....), a case arising under the Walsh-Healey Public Contracts Act. Such a contract, which may be in the...

Combined alkaline hydrolysis and ultrasound-assisted extraction for the release of nonextractable phenolics from cauliflower (Brassica oleracea var. botrytis) waste.

PubMed

Gonzales, Gerard Bryan; Smagghe, Guy; Raes, Katleen; Van Camp, John

2014-04-16

Cauliflower waste contains high amounts phenolic compounds, but conventional solvent extraction misses high amounts of nonextractable phenolics (NEP), which may contribute more to the valorization of these waste streams. In this study, the NEP content and composition of cauliflower waste were investigated. The ability of alkaline hydrolysis, sonication, and their combination to release NEP was assessed. Alkaline hydrolysis with sonication was found to extract the highest NEP content (7.3 ± 0.17 mg gallic acid equivalents (GAE)/g dry waste), which was higher than the extractable fraction. The highest yield was obtained after treatment of 2 M NaOH at 60 °C for 30 min of sonication. Quantification and identification were done using U(H)PLC-DAD and U(H)PLC-ESI-MS(E). Kaempferol and quercetin glucosides along with several phenolic acids were found. The results of the study show that there are higher amounts of valuable health-promoting compounds from cauliflower waste than what is currently described in the literature.

Comparison of Sugars, Iridoid Glycosides and Amino Acids in Nectar and Phloem Sap of Maurandya barclayana, Lophospermum erubescens, and Brassica napus

PubMed Central

Lohaus, Gertrud; Schwerdtfeger, Michael

2014-01-01

Background Floral nectar contains sugars and amino acids to attract pollinators. In addition, nectar also contains different secondary compounds, but little is understood about their origin or function. Does nectar composition reflect phloem composition, or is nectar synthesized and/or modified in nectaries? Studies where both, the nectar as well as the phloem sap taken from the same plant species were analyzed in parallel are rare. Therefore, phloem sap and nectar from different plant species (Maurandya barclayana, Lophospermum erubescens, and Brassica napus) were compared. Methodology and Principal Findings Nectar was collected with microcapillary tubes and phloem sap with the laser-aphid-stylet technique. The nectar of all three plant species contained high amounts of sugars with different percentages of glucose, fructose, and sucrose, whereas phloem sap sugars consisted almost exclusively of sucrose. One possible reason for this could be the activity of invertases in the nectaries. The total concentration of amino acids was much lower in nectars than in phloem sap, indicating selective retention of nitrogenous solutes during nectar formation. Nectar amino acid concentrations were negatively correlated with the nectar volumes per flower of the different plant species. Both members of the tribe Antirrhineae (Plantaginaceae) M. barclayana and L. erubescens synthesized the iridoid glycoside antirrhinoside. High amounts of antirrhinoside were found in the phloem sap and lower amounts in the nectar of both plant species. Conclusions/Significance The parallel analyses of nectar and phloem sap have shown that all metabolites which were found in nectar were also detectable in phloem sap with the exception of hexoses. Otherwise, the composition of both aqueous solutions was not the same. The concentration of several metabolites was lower in nectar than in phloem sap indicating selective retention of some metabolites. Furthermore, the existence of antirrhinoside in nectar could be based on passive secretion from the phloem. PMID:24489951

Comparison of sugars, iridoid glycosides and amino acids in nectar and phloem sap of Maurandya barclayana, Lophospermum erubescens, and Brassica napus.

PubMed

Lohaus, Gertrud; Schwerdtfeger, Michael

2014-01-01

Floral nectar contains sugars and amino acids to attract pollinators. In addition, nectar also contains different secondary compounds, but little is understood about their origin or function. Does nectar composition reflect phloem composition, or is nectar synthesized and/or modified in nectaries? Studies where both, the nectar as well as the phloem sap taken from the same plant species were analyzed in parallel are rare. Therefore, phloem sap and nectar from different plant species (Maurandya barclayana, Lophospermum erubescens, and Brassica napus) were compared. Nectar was collected with microcapillary tubes and phloem sap with the laser-aphid-stylet technique. The nectar of all three plant species contained high amounts of sugars with different percentages of glucose, fructose, and sucrose, whereas phloem sap sugars consisted almost exclusively of sucrose. One possible reason for this could be the activity of invertases in the nectaries. The total concentration of amino acids was much lower in nectars than in phloem sap, indicating selective retention of nitrogenous solutes during nectar formation. Nectar amino acid concentrations were negatively correlated with the nectar volumes per flower of the different plant species. Both members of the tribe Antirrhineae (Plantaginaceae) M. barclayana and L. erubescens synthesized the iridoid glycoside antirrhinoside. High amounts of antirrhinoside were found in the phloem sap and lower amounts in the nectar of both plant species. The parallel analyses of nectar and phloem sap have shown that all metabolites which were found in nectar were also detectable in phloem sap with the exception of hexoses. Otherwise, the composition of both aqueous solutions was not the same. The concentration of several metabolites was lower in nectar than in phloem sap indicating selective retention of some metabolites. Furthermore, the existence of antirrhinoside in nectar could be based on passive secretion from the phloem.

Geochemical behavior of rare earth elements of the hydrothermal alterations within the Tepeoba porphyry Cu-Mo-Au deposits at Balikesir, NW Turkey

NASA Astrophysics Data System (ADS)

Doner, Zeynep; Abdelnasser, Amr; Kiran Yildirim, Demet; Kumral, Mustafa

2016-04-01

This work reports the geochemical characteristics and behavior of the rare earth elements (REE) of the hydrothermal alteration of the Tepeoba porphyry Cu-Mo-Au deposit located in the Anatolian tectonic belt at Biga peninsula (Locally Balikesir province), NW Turkey. The Cu-Mo-Au mineralization at this deposit hosted in the hornfels rocks and related to the silicic to intermediate intrusion of Eybek pluton. It locally formed with brecciated zones and quartz vein stockworks, as well as the brittle fracture zones associated with intense hydrothermal alteration. Three main alteration zones with gradual boundaries formed in the mine area in the hornfels rock that represents the host rock, along that contact the Eybek pluton; potassic, propylitic and phyllic alteration zones. The potassic alteration zone that formed at the center having high amount of Cu-sulfide minerals contains biotite, muscovite, and sericite with less amount of K-feldspar and associated with tourmalinization alteration. The propylitic alteration surrounds the potassic alteration having high amount of Mo and Au and contains chlorite, albite, epidote, calcite and pyrite. The phyllic alteration zone also surrounds the potassic alteration containing quartz, sericite and pyrite minerals. Based on the REE characteristics and content and when we correlate the Alteration index (AI) with the light REEs and heavy REEs of each alteration zone, it concluded that the light REEs decrease and heavy REEs increase during the alteration processes. The relationships between K2O index with Eu/Eu* and Sr/Sr* reveals a positive correlation in the potassic and phyllic alteration zones and a negative correlation in the propylitic alteration zone. This refers to the hydrothermal solution which is responsible for the studied porphyry deposits and associated potassic and phyllic alterations has a positive Eu and Sr anomaly as well as these elements were added to the altered rock from the hydrothermal solution. Keywords: Rare earth elements geochemistry; Tepeoba porphyry Cu-Mo-Au deposits; Balikesir; Turkey

Assessment of oil content and fatty acid composition variability in two economically important Hibiscus species.

PubMed

Wang, Ming Li; Morris, Brad; Tonnis, Brandon; Davis, Jerry; Pederson, Gary A

2012-07-04

The Hibiscus genus encompasses more than 300 species, but kenaf (Hibiscus cannabinus L.) and roselle (Hibiscus sabdariffa L.) are the two most economically important species within the genus. Seeds from these two Hibiscus species contain a relatively high amount of oil with two unusual fatty acids: dihydrosterculic and vernolic acids. The fatty acid composition in the oil can directly affect oil quality and its utilization. However, the variability in oil content and fatty acid composition for these two species is unclear. For these two species, 329 available accessions were acquired from the USDA germplasm collection. Their oil content and fatty acid composition were determined by nuclear magnetic resonance (NMR) and gas chromatography (GC), respectively. Using NMR and GC analyses, we found that Hibiscus seeds on average contained 18% oil and seed oil was composed of six major fatty acids (each >1%) and seven minor fatty acids (each <1%). Hibiscus cannabinus seeds contained significantly higher amounts of oil (18.14%), palmitic (20.75%), oleic (28.91%), vernolic acids (VA, 4.16%), and significantly lower amounts of stearic (3.96%), linoleic (39.49%), and dihydrosterculic acids (DHSA, 1.08%) than H. sabdariffa seeds (17.35%, 18.52%, 25.16%, 3.52%, 4.31%, 44.72%, and 1.57%, respectively). For edible oils, a higher oleic/linoleic (O/L) ratio and lower level of DHSA are preferred, and for industrial oils a high level of VA is preferred. Our results indicate that seeds from H. cannabinus may be of higher quality than H. sabdariffa seeds for these reasons. Significant variability in oil content and major fatty acids was also detected within both species. The variability in oil content and fatty acid composition revealed from this study will be useful for exploring seed utilization and developing new cultivars in these Hibiscus species.

Sodium, sugar, and fat content of complementary infant and toddler foods sold in the United States, 2015.

PubMed

Maalouf, Joyce; Cogswell, Mary E; Bates, Marlana; Yuan, Keming; Scanlon, Kelley S; Pehrsson, Pamela; Gunn, Janelle P; Merritt, Robert K

2017-06-01

Background: As part of a healthy diet, limiting intakes of excess sodium, added sugars, saturated fat, and trans fat has been recommended. The American Heart Association recommends that children aged <2 y should avoid added sugars. Objective: We sought to determine commercial complementary infant-toddler food categories that were of potential concern because of the sodium, added sugar, saturated fat, or trans fat content. Design: Nutrition label information (e.g., serving size, sodium, saturated fat, trans fat) for 1032 infant and toddler foods was collected from manufacturers' websites and stores from May to July 2015 for 24 brands, which accounted for >95% of infant-toddler food sales. The presence of added sugars was determined from the ingredient list. Reference amount customarily consumed (RACC) categories were used to group foods and standardize serving sizes. A high sodium content was evaluated on the basis of the Upper Intake Level for children aged 1-3 y and the number of potential servings per day ([i.e., 1500 mg/7 servings (>210 mg/RACC)], a sodium amount >200 mg/100 g, or a mean sodium density >1000 mg/1000 kcal. Results: In 2015, most commercial infant-only vegetables, fruit, dinners, and cereals were low in sodium, contained no saturated fat, and did not contain added sugars. On average, toddler meals contained 2233 mg Na/1000 kcal, and 84% of the meals had >210 mg Na/RACC (170 g), whereas 69% of infant-toddler savory snacks had >200 mg Na/100 g. More than 70% of toddler meals, cereal bars and breakfast pastries, and infant-toddler grain- or dairy-based desserts contained ≥1 sources of added sugar. Approximately 70% of toddler meals contained saturated fat (mean: 1.9 g/RACC), and no commercial infant-toddler foods contained trans fats. Conclusion: Most commercial toddler meals, cereal bars and breakfast pastries, and infant-toddler snacks and desserts have high sodium contents or contain added sugars, suggesting a need for continued public health efforts to support parents in choosing complementary foods for their infants and toddlers. © 2017 American Society for Nutrition.

CO2 mineral sequestration in oil-shale wastes from Estonian power production.

PubMed

Uibu, Mai; Uus, Mati; Kuusik, Rein

2009-02-01

In the Republic of Estonia, local low-grade carbonaceous fossil fuel--Estonian oil-shale--is used as a primary energy source. Combustion of oil-shale is characterized by a high specific carbon emission factor (CEF). In Estonia, the power sector is the largest CO(2) emitter and is also a source of huge amounts of waste ash. Oil-shale has been burned by pulverized firing (PF) since 1959 and in circulating fluidized-bed combustors (CFBCs) since 2004-2005. Depending on the combustion technology, the ash contains a total of up to 30% free Ca-Mg oxides. In consequence, some amount of emitted CO(2) is bound by alkaline transportation water and by the ash during hydraulic transportation and open-air deposition. The goal of this study was to investigate the possibility of improving the extent of CO(2) capture using additional chemical and technological means, in particular the treatment of aqueous ash suspensions with model flue gases containing 10-15% CO(2). The results indicated that both types of ash (PF and CFBC) could be used as sorbents for CO(2) mineral sequestration. The amount of CO(2) captured averaged 60-65% of the carbonaceous CO(2) and 10-11% of the total CO(2) emissions.

Heterodyne method for high specificity gas detection.

NASA Technical Reports Server (NTRS)

Dimeff, J.; Donaldson, R. W.; Gunter, W. D., Jr.; Jaynes, D. N.; Margozzi, A. P.; Deboo, G. J.; Mcclatchie, E. A.; Williams, K. G.

1971-01-01

This paper describes a new technique for measuring trace quantities of gases. The technique involves the use of a reference cell (containing a known amount of the gas being sought) and a sample cell (containing an unknown amount of the same gas) wherein the gas densities are modulated. Light passing through the two cells in sequence is modulated in intensity at the vibrational-rotational lines characteristic of the absorption spectrum for the gas of interest. Since the absorption process is nonlinear, modulating the two absorption cells at two different frequencies gives rise to a heterodyning effect, which in turn introduces sum and difference frequencies in the detected signal. Measuring the ratio of the difference frequency signal for example, to the signal introduced by the reference cell provides a normalized measure of the amount of the gas in the sample cell. The readings produced are thereby independent of source intensity, window transparency, and detector sensitivity. Experimental evaluation of the technique suggests that it should be applicable to a wide range of gases, that it should be able to reject spurious signals due to unwanted gases, and that it should be sensitive to concentrations of the order of 10 to the minus 8th power when used with a sample cell of only 20 cm length.

Evaluation of Crayfish Growth and Assimilation on Animal and Detrital Food Sources: Are Stable Isotopes Telling the Whole Story?

NASA Astrophysics Data System (ADS)

Warren, L. L.; Wotton, R. S.; Wharton, G.; Fortino, K.; Ulseth, A. J.; Hershey, A. E.

2005-05-01

Crayfish are the dominant omnivores of many ecosystems and have strong direct and indirect effects through predation and organic matter processing. Despite this, the importance of detritus for crayfish production is poorly understood. We conducted a laboratory experiment where we fed crayfish an ad. lib. diet of only detritus, only fish tissue, or a mixture the above. The crayfish grew more on a diet which contained meat but growth was highly correlated with the amount of food consumed. The least amount of food was consumed in the detritus treatment, an intermediate amount of food in the meat treatment, and the most food in the mix treatment, suggesting that consumption of detritus by crayfish is related to more than simply the abundance of detritus. Nonetheless, isotopic evidence indicated that the crayfish were not assimilating leaf C and N. Additionally, crayfish in the meat containing treatments never exceeded the del 15N signature of their source by the approximately 3 units expected following fractionation, despite coming to isotopic equilibrium with their source. These findings suggest that crayfish may fractionate C and N uniquely. This difference may have to do with gut microbial activity and may have implications for the interpretation crayfish isotopic signatures.

In vitro Studies of the Gain and Exchange of Calcium in Frog Skeletal Muscle

PubMed Central

Cosmos, Ethel; Harris, Eric J.

1961-01-01

(1) The Ca++, Na+, and K+ contents of frog sartorius muscles were found analytically after exposure to various media including some containing labeled Ca++. (2) During storage in media with 100 to 120 mM Na+ and 1 mM Ca++ both Na+ and Ca++ are gained while K+ is lost; there is a high correlation between Na+ and Ca++ gains. (3) When Ca++ gain occurs from a solution containing labeled Ca++ there is also some exchange of the original Ca++ with the labeled Ca++. The amount exchanged is considerably less (e.g. 50 per cent) than the total amount of labeled Ca++ taken up by the tissue. (4) When the external Na+ concentration is reduced to 30 mM the amount of labeled Ca++ taken up is increased. Part of the increase is attributable to a greater net gain and part to a greater degree of exchange. (5) It is pointed out that muscles which have been loaded in vitro with labeled Ca++ will not provide a valid measure of the exchangeability of the normal Ca++ content present at the time of dissection. (6) Comparison is made between results obtained using Sr89 and Ca45 as labels for the Ca++. Little, if any, difference is perceptible. PMID:13695749

75 FR 50793 - Bureau of Political-Military Affairs: Directorate of Defense Trade Controls; Notifications to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-17

... of $25,000,000 or more. The transaction contained in the attached certification involves the export... articles in the amount of $50,000,000 or more. The transaction contained in the attached certification... military equipment abroad and the export of firearms in the amount of $1,000,000 or more. The transaction...

Interaction between the effects of evaporation rate and amount of simulated rainfall on development of the free-living stages of Haemonchus contortus.

PubMed

O'Connor, Lauren J; Kahn, Lewis P; Walkden-Brown, Stephen W

2008-08-17

A factorial experiment (3 x 4 x 2 x 3) was conducted in programmable incubators to investigate interaction between the effects of rainfall amount, rainfall distribution and evaporation rate on development of Haemonchus contortus to L3. Sheep faeces containing H. contortus eggs were incubated on sterilised soil under variable temperatures typical of summer in the Northern Tablelands of NSW, Australia. Simulated rainfall was applied in 1 of 3 amounts (12, 24 or 32 mm) and 4 distributions (a single event on the day after deposition, or the same total amount split in 2, 3 or 4 equal events over 2, 3 or 4 days, respectively). Samples were incubated at either a Low or High rate of evaporation (Low: 2.1-3.4 mm/day and High: 3.8-6.1 mm/day), and faeces and soil were destructively sampled at 4, 7 and 14 days post-deposition. Recovery of L3 from the soil (extra-pellet L3) increased over time (up to 0.52% at day 14) and with each increment of rainfall (12 mm: <0.01%; 24 mm: 0.10%; 32 mm: 0.45%) but was reduced under the High evaporation rate (0.01%) compared with the Low evaporation rate (0.31%). All rainfall amounts yielded significantly different recoveries of L3 under Low evaporation rates but there was no difference between the 12 and 24 mm treatments under the High evaporation rate. The distribution of simulated rainfall did not significantly affect recovery of infective larvae. Faecal moisture content was positively associated with L3 recovery, as was the ratio of cumulative precipitation and cumulative evaporation (P/E), particularly when measured in the first 4 days post-deposition. The results show that evaporation rate plays a significant role in regulating the influence of rainfall amount on the success of L3 transmission.

Potential of Extracted Locusta Migratoria Protein Fractions as Value-Added Ingredients.

PubMed

Clarkson, Claudia; Mirosa, Miranda; Birch, John

2018-02-09

Although locusts can be sustainably produced and are nutrient rich, the thought of eating them can be hard to swallow for many consumers. This paper aims to investigate the nutritional composition of Locusta migratoria , including the properties of extracted locust protein, contributing to limited literature and product development opportunities for industry. Locusts sourced from Dunedin, New Zealand, contained a high amount of protein (50.79% dry weight) and fat (34.93%), which contained high amounts of omega-3 (15.64%), creating a desirably low omega-3/omega-6 ratio of 0.57. Three protein fractions including; insoluble locust fraction, soluble locust fraction, and a supernatant fraction were recovered following alkali isoelectric precipitation methodology. Initially, proteins were solubilised at pH 10 then precipitated out at the isoelectric point (pH 4). All fractions had significantly higher protein contents compared with the whole locust. The insoluble protein fraction represented 37.76% of the dry weight of protein recovered and was much lighter in colour and greener compared to other fractions. It also had the highest water and oil holding capacity of 5.17 mL/g and 7.31 mL/g, possibly due to larger particle size. The high supernatant yield (56.60%) and low soluble protein yield (9.83%) was unexpected and could be a result of experimental pH conditions chosen.

Wheat leaf lipids during heat stress: I. High day and night temperatures result in major lipid alterations.

PubMed

Narayanan, Sruthi; Tamura, Pamela J; Roth, Mary R; Prasad, P V Vara; Welti, Ruth

2016-04-01

Understanding how wheat (Triticum aestivum L.) plants under high temperature (HT) regulate lipid composition is critical to developing climate-resilient varieties. We measured 165 glycerolipids and sterol derivatives under optimum and high day and night temperatures in wheat leaves using electrospray ionization-tandem mass spectrometry. Levels of polar lipid fatty acyl chain unsaturation were lower in both heat-tolerant genotype Ventnor and susceptible genotype Karl 92 under HT, compared with optimum temperature. The lower unsaturation was predominantly because of lower levels of 18:3 acyl chains and higher levels of 18:1 and 16:0 acyl chains. Levels of 18:3-containing triacylglycerols increased threefold/more under HT, consistent with their possible role in sequestering fatty acids during membrane lipid remodelling. Phospholipids containing odd-numbered or oxidized acyl chains accumulated in leaves under HT. Sterol glycosides (SG) and 16:0-acylated sterol glycosides (ASG) were higher under HT than optimum temperatures. Ventnor had lower amounts of phospholipids with oxidized acyl chains under HT and higher amounts of SG and 16:0-ASG than Karl 92. Taken together, the data demonstrate that wheat leaf lipid composition is altered by HT, in which some lipids are particularly responsive to HT, and that two wheat genotypes, chosen for their differing physiological responses to HT, differ in lipid profile under HT. © 2015 John Wiley & Sons Ltd.

Wheat leaf lipids during heat stress: I. High day and night temperatures result in major lipid alterations

PubMed Central

Narayanan, Sruthi; Tamura, Pamela J.; Roth, Mary R.; Vara Prasad, P.V.; Welti, Ruth

2016-01-01

Understanding how wheat (Triticum aestivum L.) plants under high temperature (HT) regulate lipid composition is critical to developing climate-resilient varieties. We measured 165 glycerolipids and sterol derivatives under optimum and high day and night temperatures in wheat leaves using electrospray ionization-tandem mass spectrometry. Levels of polar lipid fatty acyl chain unsaturation were lower in both heat-tolerant genotype Ventnor and susceptible genotype Karl 92 under HT, compared to optimum temperature. The lower unsaturation was predominantly due to lower levels of 18:3 and higher levels of 18:1 and 16:0 acyl chains. Levels of 18:3-containing triacylglycerols increased 3-fold/more under HT, consistent with their possible role in sequestering fatty acids during membrane lipid remodeling. Phospholipids containing odd-numbered or oxidized acyl chains accumulated in leaves under HT. Sterol glycosides (SG) and 16:0-acylated sterol glycosides (ASG) were higher under HT than optimum temperatures. Ventnor had lower amounts of phospholipids with oxidized acyl chains under HT and higher amounts of SG and 16:0-ASG than Karl 92. Taken together, the data demonstrate that wheat leaf lipid composition is altered by HT, that some lipids are particularly responsive to HT, and that two wheat genotypes, chosen for their differing physiological responses to HT, differ in lipid profile under HT. PMID:26436679

Potential of Extracted Locusta Migratoria Protein Fractions as Value-Added Ingredients

PubMed Central

Birch, John

2018-01-01

Although locusts can be sustainably produced and are nutrient rich, the thought of eating them can be hard to swallow for many consumers. This paper aims to investigate the nutritional composition of Locusta migratoria, including the properties of extracted locust protein, contributing to limited literature and product development opportunities for industry. Locusts sourced from Dunedin, New Zealand, contained a high amount of protein (50.79% dry weight) and fat (34.93%), which contained high amounts of omega-3 (15.64%), creating a desirably low omega-3/omega-6 ratio of 0.57. Three protein fractions including; insoluble locust fraction, soluble locust fraction, and a supernatant fraction were recovered following alkali isoelectric precipitation methodology. Initially, proteins were solubilised at pH 10 then precipitated out at the isoelectric point (pH 4). All fractions had significantly higher protein contents compared with the whole locust. The insoluble protein fraction represented 37.76% of the dry weight of protein recovered and was much lighter in colour and greener compared to other fractions. It also had the highest water and oil holding capacity of 5.17 mL/g and 7.31 mL/g, possibly due to larger particle size. The high supernatant yield (56.60%) and low soluble protein yield (9.83%) was unexpected and could be a result of experimental pH conditions chosen. PMID:29425143

Method for removing metal vapor from gas streams

DOEpatents

Ahluwalia, R.K.; Im, K.H.

1996-04-02

A process for cleaning an inert gas contaminated with a metallic vapor, such as cadmium, involves withdrawing gas containing the metallic contaminant from a gas atmosphere of high purity argon; passing the gas containing the metallic contaminant to a mass transfer unit having a plurality of hot gas channels separated by a plurality of coolant gas channels; cooling the contaminated gas as it flows upward through the mass transfer unit to cause contaminated gas vapor to condense on the gas channel walls; regenerating the gas channels of the mass transfer unit; and, returning the cleaned gas to the gas atmosphere of high purity argon. The condensing of the contaminant-containing vapor occurs while suppressing contaminant particulate formation, and is promoted by providing a sufficient amount of surface area in the mass transfer unit to cause the vapor to condense and relieve supersaturation buildup such that contaminant particulates are not formed. Condensation of the contaminant is prevented on supply and return lines in which the contaminant containing gas is withdrawn and returned from and to the electrorefiner and mass transfer unit by heating and insulating the supply and return lines. 13 figs.

Method for removing metal vapor from gas streams

DOEpatents

Ahluwalia, R. K.; Im, K. H.

1996-01-01

A process for cleaning an inert gas contaminated with a metallic vapor, such as cadmium, involves withdrawing gas containing the metallic contaminant from a gas atmosphere of high purity argon; passing the gas containing the metallic contaminant to a mass transfer unit having a plurality of hot gas channels separated by a plurality of coolant gas channels; cooling the contaminated gas as it flows upward through the mass transfer unit to cause contaminated gas vapor to condense on the gas channel walls; regenerating the gas channels of the mass transfer unit; and, returning the cleaned gas to the gas atmosphere of high purity argon. The condensing of the contaminant-containing vapor occurs while suppressing contaminant particulate formation, and is promoted by providing a sufficient amount of surface area in the mass transfer unit to cause the vapor to condense and relieve supersaturation buildup such that contaminant particulates are not formed. Condensation of the contaminant is prevented on supply and return lines in which the contaminant containing gas is withdrawn and returned from and to the electrorefiner and mass transfer unit by heating and insulating the supply and return lines.

Formation of soft magnetic high entropy amorphous alloys composites containing in situ solid solution phase

NASA Astrophysics Data System (ADS)

Wei, Ran; Sun, Huan; Chen, Chen; Tao, Juan; Li, Fushan

2018-03-01

Fe-Co-Ni-Si-B high entropy amorphous alloys composites (HEAACs), which containing high entropy solid solution phase in amorphous matrix, show good soft magnetic properties and bending ductility even in optimal annealed state, were successfully developed by melt spinning method. The crystallization phase of the HEAACs is solid solution phase with body centered cubic (BCC) structure instead of brittle intermetallic phase. In addition, the BCC phase can transformed into face centered cubic (FCC) phase with temperature rise. Accordingly, Fe-Co-Ni-Si-B high entropy alloys (HEAs) with FCC structure and a small amount of BCC phase was prepared by copper mold casting method. The HEAs exhibit high yield strength (about 1200 MPa) and good plastic strain (about 18%). Meanwhile, soft magnetic characteristics of the HEAs are largely reserved from HEAACs. This work provides a new strategy to overcome the annealing induced brittleness of amorphous alloys and design new advanced materials with excellent comprehensive properties.

Light Moderates the Induction of Phosphoenolpyruvate Carboxylase by NaCl and Abscisic Acid in Mesembryanthemum crystallinum 1

PubMed Central

McElwain, Elizabeth F.; Bohnert, Hans J.; Thomas, John C.

1992-01-01

In Mesembryanthemum crystallinum, phosphoenolpyruvate carboxylase is synthesized de novo in response to osmotic stress, as part of the switch from C3-photosynthesis to Crassulacean acid metabolism. To better understand the environmental signals involved in this pathway, we have investigated the effects of light on the induced expression of phosphoenolpyruvate carboxylase mRNA and protein in response to stress by 400 millimolar NaCl or 10 micromolar abscisic acid in hydroponically grown plants. When plants were grown in high-intensity fluorescent or incandescent light (850 microeinsteins per square meter per second), NaCl and abscisic acid induced approximately an eightfold accumulation of phosphoenolpyruvate carboxylase mRNA when compared to untreated controls. Levels of phosphoenolpyruvate carboxylase protein were high in these abscisic acid- and NaCl-treated plants, and detectable in the unstressed control. Growth in high-intensity incandescent (red) light resulted in approximately twofold higher levels of phosphoenolpyruvate carboxylase mRNA in the untreated plants when compared to control plants grown in high-intensity fluorescent light. In low light (300 microeinsteins per square meter per second fluorescent), only NaCl induced mRNA levels significantly above the untreated controls. Low light grown abscisic acid- and NaCl-treated plants contained a small amount of phosphoenolpyruvate carboxylase protein, whereas the (untreated) control plants did not contain detectable amounts of phosphoenolpyruvate carboxylase. Environmental stimuli, such as light and osmotic stress, exert a combined effect on gene expression in this facultative halophyte. ImagesFigure 1Figure 2 PMID:16668999

MYRRHA: A multipurpose nuclear research facility

NASA Astrophysics Data System (ADS)

Baeten, P.; Schyns, M.; Fernandez, Rafaël; De Bruyn, Didier; Van den Eynde, Gert

2014-12-01

MYRRHA (Multi-purpose hYbrid Research Reactor for High-tech Applications) is a multipurpose research facility currently being developed at SCK•CEN. MYRRHA is based on the ADS (Accelerator Driven System) concept where a proton accelerator, a spallation target and a subcritical reactor are coupled. MYRRHA will demonstrate the ADS full concept by coupling these three components at a reasonable power level to allow operation feedback. As a flexible irradiation facility, the MYRRHA research facility will be able to work in both critical as subcritical modes. In this way, MYRRHA will allow fuel developments for innovative reactor systems, material developments for GEN IV and fusion reactors, and radioisotope production for medical and industrial applications. MYRRHA will be cooled by lead-bismuth eutectic and will play an important role in the development of the Pb-alloys technology needed for the LFR (Lead Fast Reactor) GEN IV concept. MYRRHA will also contribute to the study of partitioning and transmutation of high-level waste. Transmutation of minor actinides (MA) can be completed in an efficient way in fast neutron spectrum facilities, so both critical reactors and subcritical ADS are potential candidates as dedicated transmutation systems. However critical reactors heavily loaded with fuel containing large amounts of MA pose reactivity control problems, and thus safety problems. A subcritical ADS operates in a flexible and safe manner, even with a core loading containing a high amount of MA leading to a high transmutation rate. In this paper, the most recent developments in the design of the MYRRHA facility are presented.

Comparing the effects of sucrose and high-fructose corn syrup on lipid metabolism and the risk of cardiovascular disease in male rats.

PubMed

Sadowska, Joanna; Bruszkowska, Magda

2017-01-01

The objective of this study was to compare, in an animal model, the effect of different sugar types (sucrose vs. high-fructose corn syrup 55%) consumed as 10% by weight of the diet (11.6% of daily caloric intake) on the amount of food consumed, body weight, fatty tissue deposits, concentrations of selected lipids, and atherogenic indices of blood plasma. Material and method. The experiment was carried out on 30 5-month-old Wistar male rats, fed three differ- ent diets, containing, amongst other foods, (1) ground unrefined cereal grains, (2) sucrose, (3) high-fructose corn syrup. Results. Weight gains in animals on sucrose or high-fructose corn syrup diets were higher than those con- suming basic feed, but the effect was not associated with perivisceral fat accumulation. It has been found that all the atherogenic indices (Castelli’s Risk Index I, Castelli’s Risk Index II, Atherogenic Index of Plasma, Atherogenic Coefficient) were statistically significantly higher in animals on a high-fructose corn syrup diet compared to both the control group and those on a sucrose diet. Conclusion. The effect of the 55% high-fructose corn syrup on the tested parameters of lipid metabolism was not equivalent to that of sucrose. Using HFCS-55 instead of sucrose has an adverse effect on blood lipid parameters, while weight gains and peri-organ fat deposits are comparable. Moreover, the obtained results confirm that tested animals were susceptible to the adverse effects of sugars added to their diet, even in small amounts. This emphasises the need to precisely control the amount of added sugars in. nd. The objective of this study was to compare, in an animal model, the effect of different sugar types (sucrose vs. high-fructose corn syrup 55%) consumed as 10% by weight of the diet (11.6% of daily caloric intake) on the amount of food consumed, body weight, fatty tissue deposits, concentrations of selected lipids, and atherogenic indices of blood plasma. Material and method. The experiment was carried out on 30 5-month-old Wistar male rats, fed three differ- ent diets, containing, amongst other foods, (1) ground unrefined cereal grains, (2) sucrose, (3) high-fructose corn syrup. Weight gains in animals on sucrose or high-fructose corn syrup diets were higher than those con- suming basic feed, but the effect was not associated with perivisceral fat accumulation. It has been found that all the atherogenic indices (Castelli’s Risk Index I, Castelli’s Risk Index II, Atherogenic Index of Plasma, Atherogenic Coefficient) were statistically significantly higher in animals on a high-fructose corn syrup diet compared to both the control group and those on a sucrose diet. The effect of the 55% high-fructose corn syrup on the tested parameters of lipid metabolism was not equivalent to that of sucrose. Using HFCS-55 instead of sucrose has an adverse effect on blood lipid parameters, while weight gains and peri-organ fat deposits are comparable. Moreover, the obtained results confirm that tested animals were susceptible to the adverse effects of sugars added to their diet, even in small amounts. This emphasises the need to precisely control the amount of added sugars in the diet.

A rapid Orthopoxvirus purification protocol suitable for high-containment laboratories.

PubMed

Hughes, Laura; Wilkins, Kimberly; Goldsmith, Cynthia S; Smith, Scott; Hudson, Paul; Patel, Nishi; Karem, Kevin; Damon, Inger; Li, Yu; Olson, Victoria A; Satheshkumar, P S

2017-05-01

Virus purification in a high-containment setting provides unique challenges due to barrier precautions and operational safety approaches that are not necessary in lower biosafety level (BSL) 2 environments. The need for high risk group pathogen diagnostic assay development, anti-viral research, pathogenesis and vaccine efficacy research necessitates work in BSL-3 and BSL-4 labs with infectious agents. When this work is performed in accordance with BSL-4 practices, modifications are often required in standard protocols. Classical virus purification techniques are difficult to execute in a BSL-3 or BSL-4 laboratory because of the work practices used in these environments. Orthopoxviruses are a family of viruses that, in some cases, requires work in a high-containment laboratory and due to size do not lend themselves to simpler purification methods. Current CDC purification techniques of orthopoxviruses uses 1,1,2-trichlorotrifluoroethane, commonly known as Genetron ® . Genetron ® is a chlorofluorocarbon (CFC) that has been shown to be detrimental to the ozone and has been phased out and the limited amount of product makes it no longer a feasible option for poxvirus purification purposes. Here we demonstrate a new Orthopoxvirus purification method that is suitable for high-containment laboratories and produces virus that is not only comparable to previous purification methods, but improves on purity and yield. Published by Elsevier B.V.

Silica nanoparticles carrying boron-containing polymer brushes

NASA Astrophysics Data System (ADS)

Brozek, Eric M.; Mollard, Alexis H.; Zharov, Ilya

2014-05-01

A new class of surface-modified silica nanoparticles has been developed for potential applications in boron neutron capture therapy. Sub-50 nm silica particles were synthesized using a modified Stöber method and used in surface-initiated atom transfer radical polymerization of two biocompatible polymers, poly(2-(hydroxyethyl)methacrylate) and poly(2-(methacryloyloxy)ethyl succinate). The carboxylic acid and hydroxyl functionalities of the polymeric side chains were functionalized with carboranyl clusters in high yields. The resulting particles were characterized using DLS, TEM, solution 1H NMR, solid state 11B NMR and thermogravimetric analysis. The particles contain between 13 and 18 % of boron atoms by weight, which would provide a high amount of 10B nuclides for BNCT, while the polymer chains are suitable for further modification with cell targeting ligands.

Compositional stratigraphy of crustal material from near-infrared spectra

NASA Technical Reports Server (NTRS)

Pieters, Carle M.

1987-01-01

An Earth-based telescopic program to acquire near-infrared spectra of freshly exposed lunar material now contains data for 17 large impact craters with central peaks. Noritic, gabbroic, anorthositic and troctolitic rock types can be distinguished for areas within these large craters from characteristic absorptions in individual spectra of their walls and central peaks. Norites dominate the upper lunar crust while the deeper crustal zones also contain significant amounts of gabbros and anorthosites. Data for material associated with large craters indicate that not only is the lunar crust highly heterogeneous across the nearside, but that the compositional stratigraphy of the lunar crust is nonuniform. Crustal complexity should be expected for other planetary bodies, which should be studied using high spatial and spectral resolution data in and around large impact craters.

The Daily Consumption of Cola Can Determine Hypocalcemia: A Case Report of Postsurgical Hypoparathyroidism-Related Hypocalcemia Refractory to Supplemental Therapy with High Doses of Oral Calcium.

PubMed

Guarnotta, Valentina; Riela, Serena; Massaro, Marina; Bonventre, Sebastiano; Inviati, Angela; Ciresi, Alessandro; Pizzolanti, Giuseppe; Benvenga, Salvatore; Giordano, Carla

2017-01-01

The consumption of soft drinks is a crucial factor in determining persistent hypocalcemia. The aim of the study is to evaluate the biochemical mechanisms inducing hypocalcemia in a female patient with usual high consumption of cola drink and persistent hypocalcemia, who failed to respond to high doses of calcium and calcitriol supplementation. At baseline and after pentagastrin injection, gastric secretion (Gs) and duodenal secretion (Ds) samples were collected and calcium and total phosphorus (P tot ) concentrations were evaluated. At the same time, blood calcium, P tot , sodium, potassium, chloride, magnesium concentrations, and vitamin D were sampled. After intake of cola (1 L) over 180 min, Gs and Ds and blood were collected and characterized in order to analyze the amount of calcium and P tot or sodium, potassium, magnesium, and chloride ions, respectively. A strong pH decrease was observed after cola intake with an increase in phosphorus concentration. Consequently, a decrease in calcium concentration in Gs and Ds was observed. A decrease in calcium concentration was also observed in blood. In conclusion, we confirm that in patients with postsurgical hypoparathyroidism, the intake of large amounts of cola containing high amounts of phosphoric acid reduces calcium absorption efficiency despite the high doses of calcium therapy.

Erythrocyte haemolysate interacts with ATP-Fe to form a complex containing iron, ATP and 13 800 MW polypeptide.

PubMed

Weaver, J; Zhan, H; Pollack, S

1993-01-01

Iron first entering the reticulocyte is bound to ATP in the low MW cytosolic pool; some is also 'loosely bound' to haemoglobin, coeluting with haemoglobin from a molecular sieve column though not incorporated into haem. When haemolysate is mixed with ATP-Fe in vitro a similar high MW iron-containing complex is formed: the ATP-Fe interacts with a non-haemoglobin constituent of the haemolysate to form a high MW ATP-Fe complex in which the ratio of ATP:Fe (originally 6:1) is reversed, so that the complex contains more iron than ATP. The high MW ATP-Fe complex is formed even when ATP is in 150-fold molar excess and is formed without detectable hydrolysis of the ATP. The activity of haemolysate in forming the high MW ATP-Fe complex is not diminished by dialysis; all of the activity is recovered in the haemoglobin-containing fraction obtained from an Ultrogel AcA 44 column. The activity does not derive from haemoglobin since 85% of the activity is removed when haemoglobin is purified from haemolysate with DEAE-Sephadex. The chelatable iron pool of the cell probably includes both the high MW ATP-Fe complex and low MW ATP-Fe. Shunting of ATP-Fe to a high MW aggregate reduces the amount of iron present in the highly reactive low MW form and thus probably serves to limit the formation of cell damaging radicals.

Consumer understanding of calorie amounts and serving size: implications for nutritional labelling.

PubMed

Vanderlee, Lana; Goodman, Samantha; Sae Yang, Wiworn; Hammond, David

2012-07-18

Increased consumption of sugar-sweetened beverages has contributed to rising obesity levels. Under Canadian law, calories for pre-packaged foods and beverages are presented by serving size; however, serving sizes differ across products and even for the same product in different containers. This study examined consumer understanding of calorie amounts for government nutrition labels and industry labelling schemes. A national sample of 687 Canadian adults completed an online survey. Participants were randomized to view images of Coke® bottles that displayed different serving sizes and calorie amounts. Participants viewed either the regulated nutrition information on the "back" of containers, or the voluntary calorie symbols displayed on the "front" of Coke® products. Participants were asked to determine how many calories the bottle contained. Across all conditions, 54.2% of participants correctly identified the number of calories in the beverage. Participants who viewed government-mandated nutrition information were more likely to answer correctly (59.0%) than those who saw industry labelling (49.1%) (OR=5.3, 95% CI: 2.6-10.6). Only 11.8% who viewed the Coke® bottle with calorie amounts per serving correctly identified the calorie amount, compared to 91.8% who saw calorie amounts per container, regardless of whether information was presented in the Nutrition Facts Table or the front-of-pack symbol (OR=242.9, 95% CI: 112.1-526.2). Few individuals can use nutrition labels to correctly identify calorie content when presented per serving or using industry labelling schemes. The findings highlight the importance of revising labelling standards and indicate that industry labelling initiatives warrant greater scrutiny.

Anxiolytic-Like Actions of Fatty Acids Identified in Human Amniotic Fluid

PubMed Central

García-Ríos, Rosa Isela; Rodríguez-Landa, Juan Francisco; Contreras, Carlos M.

2013-01-01

Eight fatty acids (C12–C18) were previously identified in human amniotic fluid, colostrum, and milk in similar proportions but different amounts. Amniotic fluid is well known to be the natural environment for development in mammals. Interestingly, amniotic fluid and an artificial mixture of fatty acids contained in amniotic fluid produce similar anxiolytic-like actions in Wistar rats. We explored whether the lowest amount of fatty acids contained in amniotic fluid with respect to colostrum and milk produces such anxiolytic-like effects. Although a trend toward a dose-response effect was observed, only an amount of fatty acids that was similar to amniotic fluid fully mimicked the effect of diazepam (2 mg/kg, i.p.) in the defensive burying test, an action devoid of effects on locomotor activity and motor coordination. Our results confirm that the amount of fatty acids contained in amniotic fluid is sufficient to produce anxiolytic-like effects, suggesting similar actions during intrauterine development. PMID:23737729

Formation of Residual Gases from Source Materials in Closed Crystal Growth Systems

NASA Technical Reports Server (NTRS)

Palosz, W.; Rose, M. Franklin (Technical Monitor)

2001-01-01

Different, non-constituent cases are present in crystal growth systems and may affect processes like growth rate in PVT or voids formation and detached solidification in melt growth systems. The presence of the gas may be detrimental or advantageous depending on its amount and composition, and on the process in question. The presence of the cases, their amount and composition, can be caused and changed by diffusion through and desorption from the growth container material. We have investigated these phenomena for silica glass ampoules. We also found, that residual cases can be generated by the source materials: even very high purity commercial elements and compounds may contain trace amounts of impurities, particularly oxides. The oxides may have low volatilities themselves but their reaction with other species, particularly carbon and hydrogen, may produce volatile compounds like water or carbon oxides. The amount of the gas and its composition is dependent on the original purity of the material (oxide contaminants) and the heat treatment of the source prior to sealing. In many cases. particularly at temperatures below about 900 C and in well-outgassed ampoules, this mechanism dominates. The problem is of a particular importance in sealed systems where the amount and composition of the gas cannot be directly controlled. Therefore, a reasonable knowledge and understanding of the origin, composition, magnitude, and change with time of gases present in sealed ampoules may be important for a meaningful control and interpretation of crystal growth processes. We have investigated this phenomenon in more details for a number of elements and compounds, primarily for II-VI and IV-VI materials. Different source pre-treatment and annealing procedures were applied, and subsequent consecutive annealings and measurements were done to determine the origin and development of the gas in the systems.

Infected Atopic Dermatitis Lesions Contain Pharmacologic Amounts of Lipoteichoic Acid

PubMed Central

Travers, Jeffrey B.; Kozman, Amal; Mousdicas, Nico; Saha, Chandan; Landis, Megan; Al-Hassani, Mohammed; Yao, Weiguo; Yao, Yongxue; Hyatt, Ann-Marie; Sheehan, Michael P.; Haggstrom, Anita N.; Kaplan, Mark H.

2009-01-01

Background Bacterial infection with Staphylococcus aureus is a known trigger for worsening of atopic dermatitis (AD); the exact mechanisms by which bacterial infection worsens dermatitis are unknown. Objective We sought to characterize the amounts of the biologically active bacterial lipoprotein lipoteichoic acid (LTA) in infected AD lesions. Methods Eighty-nine children with clinically impetiginized lesions of AD were enrolled in this study. A lesion was graded clinically using the Eczema Area and Severity Index (EASI), and then wash fluid obtained from the lesion for quantitative bacterial culture, and measurement of LTA and cytokines. The staphylococcal isolate was tested for antibiotic susceptibilities. The patients were treated with a regimen that included topical corticosteroids and systemic antibiotics and the lesion was re-analyzed after two weeks. Results S. aureus was identified in 79 of 89 children enrolled in the study. The bacterial CFU correlated with the EASI lesional score (p = 0.04). LTA levels up to 9.8 μg/ml were measured in the wash fluid samples and the amounts correlated with the lesional EASI scores (p = 0.01) and S. aureus CFU (p < 0.001). Approximately 30% of clinically impetiginized AD lesions contained greater than 1 μg/ml LTA, amounts that exert effects on various cell types in vitro. Moreover, injection of skin tissue ex vivo with amounts of LTA found in AD lesions resulted in epidermal cytokine gene expression. Conclusions Pharmacologic levels of LTA are found in many infected atopic dermatitis lesions. Clinical Implications These findings suggest that staphylococcal LTA could be an important mediator of the increased skin inflammation associated with infected AD. Capsule Summary These studies demonstrate high levels of staphylococcal LTA are found on impetiginized AD lesions. Moreover, subjects harboring MRSA exhibited greater total body involvement of AD. PMID:19962742

Tin-Doped Inorganic Amorphous Films for Use as Transparent Monolithic Phosphors.

PubMed

Masai, Hirokazu; Miyata, Hiroki; Yamada, Yasuhiro; Okumura, Shun; Yanagida, Takayuki; Kanemitsu, Yoshihiko

2015-06-10

Although inorganic crystalline phosphors can exhibit high quantum efficiency, their use in phosphor films has been limited by a reliance on organic binders that have poor durability when exposed to high-power and/or high excitation energy light sources. To address this problem, Sn(2+)-doped transparent phosphate films measuring several micrometers in thickness have been successfully prepared through heat treatment and a subsequent single dip-coating process. The resulting monolithic inorganic amorphous film exhibited an internal quantum efficiency of over 60% and can potentially utilize transmitted light. Analysis of the film's emissivity revealed that its color can be tuned by changing the amount of Mn and Sn added to influence the energy transfer from Sn(2+) to Mn(2+). It is therefore concluded that amorphous films containing such emission centers can provide a novel and viable alternative to conventional amorphous films containing crystalline phosphors in light-emitting devices.

Tin-Doped Inorganic Amorphous Films for Use as Transparent Monolithic Phosphors

PubMed Central

Masai, Hirokazu; Miyata, Hiroki; Yamada, Yasuhiro; Okumura, Shun; Yanagida, Takayuki; Kanemitsu, Yoshihiko

2015-01-01

Although inorganic crystalline phosphors can exhibit high quantum efficiency, their use in phosphor films has been limited by a reliance on organic binders that have poor durability when exposed to high-power and/or high excitation energy light sources. To address this problem, Sn2+ -doped transparent phosphate films measuring several micrometers in thickness have been successfully prepared through heat treatment and a subsequent single dip-coating process. The resulting monolithic inorganic amorphous film exhibited an internal quantum efficiency of over 60% and can potentially utilize transmitted light. Analysis of the film’s emissivity revealed that its color can be tuned by changing the amount of Mn and Sn added to influence the energy transfer from Sn2+ to Mn2+. It is therefore concluded that amorphous films containing such emission centers can provide a novel and viable alternative to conventional amorphous films containing crystalline phosphors in light-emitting devices. PMID:26061744

High intensity discharge device containing oxytrihalides

DOEpatents

Lapatovich, Walter P.; Keeffe, William M.; Liebermann, Richard W.; Maya, Jakob

1987-01-01

A fill composition for a high intensity discharge device including mercury, niobium oxytrihalide, and a molecular stabilization agent is provided. The molar ratio of niobium oxytrihalide to the molecular stabilization agent in the fill is in the range of from about 5:1 to about 7.5:1. Niobium oxytrihalide is present in the fill in sufficient amount to produce, by dissociation in the discharge, atomic niobium, niobium oxide, NbO, and niobium dioxide, NbO.sub.2, with the molar ratio of niobium-containing vapor species to mercury in the fill being in the range of from about 0.01:1 to about 0.50:1; and mercury pressure of about 1 to about 50 atmospheres at lamp operating temperature. There is also provided a high intensity discharge device comprising a sealed light-transmissive arc tube; the arc tube including the above-described fill; and an energizing means for producing an electric discharge within the arc tube.

High intensity discharge device containing oxytrihalides

DOEpatents

Lapatovich, W.P.; Keeffe, W.M.; Liebermann, R.W.; Maya, J.

1987-06-09

A fill composition for a high intensity discharge device including mercury, niobium oxytrihalide, and a molecular stabilization agent is provided. The molar ratio of niobium oxytrihalide to the molecular stabilization agent in the fill is in the range of from about 5:1 to about 7.5:1. Niobium oxytrihalide is present in the fill in sufficient amount to produce, by dissociation in the discharge, atomic niobium, niobium oxide, NbO, and niobium dioxide, NbO[sub 2], with the molar ratio of niobium-containing vapor species to mercury in the fill being in the range of from about 0.01:1 to about 0.50:1; and mercury pressure of about 1 to about 50 atmospheres at lamp operating temperature. There is also provided a high intensity discharge device comprising a sealed light-transmissive arc tube; the arc tube including the above-described fill; and an energizing means for producing an electric discharge within the arc tube. 7 figs.

Influence of biochemical composition during hydrothermal liquefaction of algae on product yields and fuel properties.

PubMed

Shakya, Rajdeep; Adhikari, Sushil; Mahadevan, Ravishankar; Shanmugam, Saravanan R; Nam, Hyungseok; Hassan, El Barbary; Dempster, Thomas A

2017-11-01

Hydrothermal liquefaction (HTL) of nine algae species were performed at two reaction temperatures (280 and 320°C) to compare the effect of their biomass composition on product yields and properties. Results obtained after HTL indicate large variations in terms of bio-oil yields and its properties. The maximum bio-oil yield (66wt%) was obtained at 320°C with a high lipid containing algae Nannochloropsis. The higher heating value of bio-oils ranged from 31 to 36MJ/kg and around 50% of the bio-oils was in the vacuum gas oil range while high lipid containing algae Nannochloropsis contained a significant portion (33-42%) in the diesel range. A predictive relationship between bio-oil yields and biochemical compositions was developed and showed a broad agreement between predictive and experimental yields. The aqueous phases obtained had high amount of TOC (12-43g/L), COD (35-160g/L), TN (1-18g/L), ammonium (0.34-12g/L) and phosphate (0.7-12g/L). Copyright © 2017 Elsevier Ltd. All rights reserved.

Response of duckweed to various concentrations of selenite.

PubMed

Mechora, Špela; Stibilj, Vekoslava; Germ, Mateja

2015-02-01

The uptake of Se(IV) and its effects on the physiological and biochemical characteristics of duckweed (Lemna minor L.) have been studied. Duckweed plants were cultivated in controlled conditions for 7 weeks in different concentrations of Na selenite: 0.5, 1, 2, 5 (exposed 42 days) and 10 mg Se L(-1) (survived 7-21 days). The addition of 1 mg Se L(-1) did not negatively affect photochemical efficiency whilst respiratory potential increased in weeks 2-4 compared to control. The addition of 1 mg Se(IV) L(-1) increased the amount of chlorophyll a in weeks 3 and 4 and the amount of carotenoids in weeks 1, 3 and 5. Concentrations of 2 and 5 mg Se L(-1) negatively affected photochemical efficiency in weeks 3 and 4, and increased respiratory potential in comparison to the control in weeks 1-4, whilst beyond week 4, the respiratory potential decreased. Plants exposed to the highest concentration of Se(IV) had to be replaced twice during the experiment because they were dying. That was reflected in photochemical efficiency as well as in respiratory potential, which decreased in time. The content of Se in duckweed increased with the increasing concentration of Se: plants growing in 0.5 mg Se L(-1) contained 0.9 mg Se g(-1) DM and plants exposed to 5 mg Se L(-1) contained 5.8 mg Se g(-1) DM. The group of plants exposed to 10 mg Se L(-1) for 21 days contained 19.5 mg Se g(-1) DM. Our study revealed that duckweed absorbed high amount of Se(IV) from the water.

Effects of Shiitake Intake on Serum Lipids in Rats Fed Different High-Oil or High-Fat Diets.

PubMed

Asada, Norihiko; Kairiku, Rumi; Tobo, Mika; Ono, Akifumi

2018-04-27

Shiitake (Lentinula edodes) extract, eritadenine, has been shown to reduce cholesterol levels, and its hypocholesterolemic actions are involved in the metabolism of methionine. However, the mechanisms by which eritadenine affects cholesterol metabolism in animals fed a high-fat diet containing different sources of lipids have not yet been elucidated in detail. This study was conducted to investigate the effects of shiitake supplementation on serum lipid concentrations in rats fed a diet including a high amount of a plant oil (HO [high oil] and HOS [high oil with shiitake] groups), animal fat (HF [high fat] and HFS [high fat with shiitake] groups), or MCT- (medium-chain triglyceride-) rich plant oil (HM [high MCT] and HMS [high MCT with shiitake] groups). Rats in the HOS, HFS, and HMS groups were fed shiitake. When rats were fed a diet containing shiitake, serum triglyceride, cholesterol levels, and LCAT (lecithin-cholesterol acyltransferase) activities were lower in rats given MCT-rich plant oil than in those that consumed lard. The lipid type in the diet with shiitake also affected serum cholesterol levels and LCAT activities. The diet containing MCT-rich plant oil showed the greatest rates of decrease in all serum lipid profiles and LCAT activities. These results suggest that shiitake and MCT-rich plant oil work together to reduce lipid profiles and LCAT activity in serum.

A comparison of the physical, chemical, and biological properties of sludges from a complete-mix activated sludge reactor and a submerged membrane bioreactor.

PubMed

Merlo, Rion P; Trussell, R Shane; Hermanowicz, Slawomir W; Jenkins, David

2007-03-01

The properties of sludges from a pilot-scale submerged membrane bioreactor (SMBR) and two bench-scale complete-mix, activated sludge (CMAS) reactors treating municipal primary effluent were determined. Compared with the CMAS sludges, the SMBR sludge contained a higher amount of soluble microbial products (SMP) and colloidal material attributed to the use of a membrane for solid-liquid separation; a higher amount nocardioform bacteria, resulting from efficient foam trapping; and a lower amount of extracellular polymeric substances (EPS), possibly because there was no selective pressure for the sludge to settle. High aeration rates in both the CMAS and SMBR reactors produced sludges with higher numbers of smaller particles. Normalized capillary suction time values for the SMBR sludge were lower than for the CMAS sludges, possibly because of its lower EPS content.

Titanium Dioxide Nanoparticles in Food and Personal Care Products

PubMed Central

Weir, Alex; Westerhoff, Paul; Fabricius, Lars

2012-01-01

Titanium dioxide is a common additive in many food, personal care, and other consumer products used by people, which after use can enter the sewage system, and subsequently enter the environment as treated effluent discharged to surface waters or biosolids applied to agricultural land, incinerated wastes, or landfill solids. This study quantifies the amount of titanium in common food products, derives estimates of human exposure to dietary (nano-) TiO2, and discusses the impact of the nanoscale fraction of TiO2 entering the environment. The foods with the highest content of TiO2 included candies, sweets and chewing gums. Among personal care products, toothpastes and select sunscreens contained 1% to >10% titanium by weight. While some other crèmes contained titanium, despite being colored white, most shampoos, deodorants, and shaving creams contained the lowest levels of titanium (<0.01 μg/mg). For several high-consumption pharmaceuticals, the titanium content ranged from below the instrument detection limit (0.0001 μg Ti/mg) to a high of 0.014 μg Ti/mg. Electron microscopy and stability testing of food-grade TiO2 (E171) suggests that approximately 36% of the particles are less than 100 nm in at least one dimension and that it readily disperses in water as fairly stable colloids. However, filtration of water solubilized consumer products and personal care products indicated that less than 5% of the titanium was able to pass through 0.45 or 0.7 μm pores. Two white paints contained 110 μg Ti/mg while three sealants (i.e., prime coat paint) contained less titanium (25 to 40 μg Ti/mg). This research showed that while many white-colored products contained titanium, it was not a prerequisite. Although several of these product classes contained low amounts of titanium, their widespread use and disposal down the drain and eventually to WWTPs deserves attention. A Monte Carlo human exposure analysis to TiO2 through foods identified children as having the highest exposures because TiO2 content of sweets is higher than other food products, and that a typical exposure for a US adult may be on the order of 1 mg Ti per kilogram body weight per day. Thus, because of the millions of tons of titanium based white pigment used annually, testing should focus on food-grade TiO2 (E171) rather than that adopted in many environmental health and safety tests (i.e., P25), which is used in much lower amounts in products less likely to enter the environment (e.g., catalyst supports, photocatalytic coatings). PMID:22260395

Interface Analyses Between a Case-Hardened Ingot Casting Steel and Carbon-Containing and Carbon-Free Refractories

NASA Astrophysics Data System (ADS)

Fruhstorfer, Jens; Dudczig, Steffen; Rudolph, Martin; Schmidt, Gert; Brachhold, Nora; Schöttler, Leandro; Rafaja, David; Aneziris, Christos G.

2018-06-01

Corrosion tests of carbon-free and carbon-containing refractories were performed. The carbon-free crucibles corroded, whereas the carbon-containing crucibles were negligibly attacked. On them, inclusions were attached. This study investigates melt oxygen contents, interface properties, and steel compositions with their non-metallic inclusions in order to explore the inclusion formation and deposition mechanisms. The carbon-free crucibles were based on alumina, mullite, and zirconia- and titania-doped alumina (AZT). The carbon-containing (-C) ones were alumina-C and AZT-C. Furthermore, nanoscaled carbon and alumina additives (-n) were applied in an AZT-C-n material. In the crucibles, the case-hardened steel 17CrNiMo7-6 was remelted at 1580 °C. It was observed that the melt and steel oxygen contents were higher for the tests in the carbon-free crucibles. Into these crucibles, the deoxidizing alloying elements Mn and Si diffused. Reducing contents of deoxidizing elements resulted in higher steel oxygen levels and less inclusions, mainly of the inclusion group SiO2-core-MnS-shell (2.5 to 8 μ m). These developed from smaller SiO2 nuclei. The inclusion amount in the steel was highest after remelting in AZT-C-n for 30 minutes but decreased strongly with increasing remelting time (60 minutes) due to inclusions' deposition on the refractory surface. The Ti from the AZT and the nanoadditives supported inclusion growth and deposition. Other inclusion groups were alumina and calcium aluminate inclusions. Their contents were high after remelting in carbon- or AZT-containing crucibles but generally decreased during remelting. On the AZT-C-n crucible, a dense layer formed from vitreous compositions including Al, Ca, Mg, Si, and Ti. To summarize, for reducing forming inclusion amounts, mullite is recommended as refractory material. For capturing formed inclusions, AZT-C-n showed a high potential.

Separation of bismuth from gram amounts of thallium and silver by cation-exchange chromatography in nitric acid.

PubMed

Meintjies, E; Strelow, F W; Victor, A H

1987-04-01

Traces and small amounts of bismuth can be separated from gram amounts of thallium and silver by successively eluting these elements with 0.3M and 0.6M nitric acid from a column containing 13 ml (3 g) of AG50W-X4, a cation-exchanger (100-200 mesh particle size) with low cross-linking. Bismuth is retained and can be eluted with 0.2M hydrobromic acid containing 20% v/v acetone, leaving many other trace elements absorbed. Elution of thallium is quite sharp, but silver shows a small amount of tailing (less than 1 gmg/ml silver in the eluate) when gram amounts are present, between 20 and 80 mug of silver appearing in the bismuth fraction. Relevant elution curves and results for the analysis of synthetic mixtures containing between 50 mug and 10 mg of bismuth and up to more than 1 g of thallium and silver are presented, as well as results for bismuth in a sample of thallium metal and in Merck thallium(I) carbonate. As little as 0.01 ppm of bismuth can be determined when the separation is combined with electrothermal atomic-absorption spectrometry.

Silver-containing polymer composition used in spacecraft and semiconductor optoelectronics control systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivanov, A. A., E-mail: alexchemtsu@rambler.ru; Tuev, V. I., E-mail: tvi-retem@main.tusur.ru

2015-10-27

The copolymer of the vinyl chloride-maleic anhydride and silver nano- and microparticle (70 wt %) composition is offered as a conductive adhesive for fixing various chips on the dielectric substrate. The wiring volume resistivity is up to 3.1×10{sup −8} Ohm×m. The adhesive strength of the silver-containing polymer composition (70% of Ag) applied under a shear on the dielectric substrate is 106 N/mm{sup 2}. Adhesive layers obtained from these substances have a high thermal conductivity up to λ = 199.93 W/m×K that depends on the amount of Ag in the polymer composition.

Information retrieval from holographic interferograms: Fundamentals and problems

NASA Technical Reports Server (NTRS)

Vest, Charles M.

1987-01-01

Holographic interferograms can contain large amounts of information about flow and temperature fields. Their information content can be very high because they can be viewed from many different directions. This multidirectionality, and fringe localization add to the information contained in the fringe pattern if diffuse illumination is used. Additional information, and increased accuracy can be obtained through the use of dual reference wave holography to add reference fringes or to effect discrete phase shift or hetrodyne interferometry. Automated analysis of fringes is possible if interferograms are of simple structure and good quality. However, in practice a large number of practical problems can arise, so that a difficult image processing task results.

Ultrafine cementitious grout

DOEpatents

Ahrens, Ernst H.

1999-01-01

An ultrafine cementitious grout in three particle grades containing Portland cement, pumice as a pozzolanic material and superplasticizer in the amounts of about 30 wt. % to about 70 wt. % Portland cement; from about 30 wt. % to about 70 wt. % pumice containing at least 70% amorphous silicon dioxide; and from 1.2 wt. % to about 5.0 wt. % superplasticizer. The superplasticizer is dispersed in the mixing water prior to the addition of dry grout and the W/CM ratio is about 0.4 to 1/1. The grout has very high strength and very low permeability with good workability. The ultrafine particle sizes allow for sealing of microfractures below 10 .mu.m in width.

The effect of weld porosity on the cryogenic fatigue strength of ELI grade Ti-5Al-2.5Sn

NASA Technical Reports Server (NTRS)

Rogers, P. R.; Lambdin, R. C.; Fox, D. E.

1992-01-01

The effect of weld porosity on the fatigue strength of ELI grade Ti-5Al-2.5Sn at cryogenic temperature was determined. A series of high cycle fatigue (HCF) and tensile tests were performed at -320 F on specimens made from welded sheets of the material. All specimens were tested with weld beads intact and some amount of weld offset. Specimens containing porosity and control specimens containing no porosity were tested. Results indicate that for the weld configuration tested, the fatigue life of the material is not affected by the presence of spherical embedded pores.

Solid phase microextraction field kit

DOEpatents

Nunes, Peter J.; Andresen, Brian D.

2005-08-16

A field kit for the collection, isolation and concentration of trace amounts of high explosives (HE), biological weapons (BW) and chemical weapons (CW) residues in air, soil, vegetation, swipe, and liquid samples. The field kit includes a number of Solid Phase Microextraction (SPME) fiber and syringe assemblies in a hermetically sealed transportation container or tubes which includes a sampling port, a number of extra SPME fiber and syringe assemblies, the fiber and syringe assemblies including a protective cap for the fiber, and an extractor for the protective cap, along with other items including spare parts, protective glove, and an instruction manual, all located in an airtight container.

Nonflammable gel electrolyte containing alkyl phosphate for rechargeable lithium batteries

NASA Astrophysics Data System (ADS)

Yoshimoto, Nobuko; Niida, Yoshihiro; Egashira, Minato; Morita, Masayuki

A nonflammable polymeric gel electrolyte has been developed for rechargeable lithium battery systems. The gel film consists of poly(vinylidenefluoride- co-hexafluoropropylene) (PVdF-HFP) swollen with lithium hexafluorophosphate (LiPF 6) solution in ternary solvent containing trimethyl phosphate (TMP). High ionic conductivity of 6.2 mS cm -1 at 20 °C was obtained for the gel electrolyte consisting of 0.8 M LiPF 6/EC + DEC + TMP (55:25:20) with PVdF-HFP, which is comparable to that of the liquid electrolyte containing the same electrolytic salt. Addition of a small amount of vinylene carbonate (VC) in the gel electrolyte improved the rechargeability of a graphite electrode. The rechargeable capacity of the graphite in the gel containing VC was ca. 300 mAh g -1, which is almost the same as that in a conventional liquid electrolyte system.

Chemical and sensory evaluation of dark chocolate with addition of quinoa (Chenopodium quinoa Willd.).

PubMed

Schumacher, Andrea B; Brandelli, Adriano; Macedo, Fernanda C; Pieta, Luiza; Klug, Tâmmila V; de Jong, Erna V

2010-03-01

Quinoa (Chenopodium quinoa Willd) is a good source of vitamin E containing high quality protein. A dark chocolate with the addition of 12, 16 or 20% quinoa was developed. The protein concentration of the products increased as the percentage of quinoa increased. The product containing 20% quinoa showed only 9% increase in vitamin E, while the quantity of polyphenols decreased from 23.5 to 18 μmol pirocatechin/g. The amount of essential amino acids was improved in samples containing quinoa. Cysteine, tyrosine and methionine increased by 104, 72, 70%, respectively in chocolate containing 20% quinoa. The amino acid pattern was as per WHO standards, which was adequate to human needs. The chocolate with quinoa was approved by 92% of the sensory panel. All the samples showed an index of acceptance above 70%. Quinoa could be used at the levels evaluated in this study adding its potential health benefit to the dark chocolate.

33 CFR 158.220 - Ports and terminals loading more than 1,000 metric tons of oil other than crude oil or bunker oil.

Code of Federal Regulations, 2011 CFR

2011-07-01

... processing in the amount of 10 metric tons (11 short tons); (b) Bilge water containing oily mixtures in the... average, whichever quantity is greater; (c) Ballast water containing oily mixtures in the amount of 30% of... FACILITIES FOR OIL, NOXIOUS LIQUID SUBSTANCES, AND GARBAGE Criteria for Reception Facilities: Oily Mixtures...

33 CFR 158.220 - Ports and terminals loading more than 1,000 metric tons of oil other than crude oil or bunker oil.

Code of Federal Regulations, 2012 CFR

2012-07-01

... processing in the amount of 10 metric tons (11 short tons); (b) Bilge water containing oily mixtures in the... average, whichever quantity is greater; (c) Ballast water containing oily mixtures in the amount of 30% of... FACILITIES FOR OIL, NOXIOUS LIQUID SUBSTANCES, AND GARBAGE Criteria for Reception Facilities: Oily Mixtures...

33 CFR 158.220 - Ports and terminals loading more than 1,000 metric tons of oil other than crude oil or bunker oil.

Code of Federal Regulations, 2014 CFR

2014-07-01

... processing in the amount of 10 metric tons (11 short tons); (b) Bilge water containing oily mixtures in the... average, whichever quantity is greater; (c) Ballast water containing oily mixtures in the amount of 30% of... FACILITIES FOR OIL, NOXIOUS LIQUID SUBSTANCES, AND GARBAGE Criteria for Reception Facilities: Oily Mixtures...

33 CFR 158.220 - Ports and terminals loading more than 1,000 metric tons of oil other than crude oil or bunker oil.

Code of Federal Regulations, 2010 CFR

2010-07-01

... processing in the amount of 10 metric tons (11 short tons); (b) Bilge water containing oily mixtures in the... average, whichever quantity is greater; (c) Ballast water containing oily mixtures in the amount of 30% of... FACILITIES FOR OIL, NOXIOUS LIQUID SUBSTANCES, AND GARBAGE Criteria for Reception Facilities: Oily Mixtures...

33 CFR 158.220 - Ports and terminals loading more than 1,000 metric tons of oil other than crude oil or bunker oil.

Code of Federal Regulations, 2013 CFR

2013-07-01

... processing in the amount of 10 metric tons (11 short tons); (b) Bilge water containing oily mixtures in the... average, whichever quantity is greater; (c) Ballast water containing oily mixtures in the amount of 30% of... FACILITIES FOR OIL, NOXIOUS LIQUID SUBSTANCES, AND GARBAGE Criteria for Reception Facilities: Oily Mixtures...

Male-Specific Transfer and Fine Scale Spatial Differences of Newly Identified Cuticular Hydrocarbons and Triacylglycerides in a Drosophila Species Pair

PubMed Central

Yew, Joanne Y.; Dreisewerd, Klaus; de Oliveira, Cássia Cardoso; Etges, William J.

2011-01-01

We analyzed epicuticular hydrocarbon variation in geographically isolated populations of D. mojavensis cultured on different rearing substrates and a sibling species, D. arizonae, with ultraviolet laser desorption/ionization mass spectrometry (UV-LDI MS). Different body parts, i.e. legs, proboscis, and abdomens, of both species showed qualitatively similar hydrocarbon profiles consisting mainly of long-chain monoenes, dienes, trienes, and tetraenes. However, D. arizonae had higher amounts of most hydrocarbons than D. mojavensis and females of both species exhibited greater hydrocarbon amounts than males. Hydrocarbon profiles of D. mojavensis populations were significantly influenced by sex and rearing substrates, and differed between body parts. Lab food–reared flies had lower amounts of most hydrocarbons than flies reared on fermenting cactus substrates. We discovered 48 male- and species-specific hydrocarbons ranging in size from C22 to C50 in the male anogenital region of both species, most not described before. These included several oxygen-containing hydrocarbons in addition to high intensity signals corresponding to putative triacylglycerides, amounts of which were influenced by larval rearing substrates. Some of these compounds were transferred to female cuticles in high amounts during copulation. This is the first study showing that triacylglycerides may be a separate class of courtship-related signaling molecules in drosophilids. This study also extends the kind and number of epicuticular hydrocarbons in these species and emphasizes the role of larval ecology in influencing amounts of these compounds, many of which mediate courtship success within and between species. PMID:21369358

Allylic ionic liquid electrolyte-assisted electrochemical surface passivation of LiCoO2 for advanced, safe lithium-ion batteries.

PubMed

Mun, Junyoung; Yim, Taeeun; Park, Jang Hoon; Ryu, Ji Heon; Lee, Sang Young; Kim, Young Gyu; Oh, Seung M

2014-08-29

Room-temperature ionic liquid (RTIL) electrolytes have attracted much attention for use in advanced, safe lithium-ion batteries (LIB) owing to their nonvolatility, high conductivity, and great thermal stability. However, LIBs containing RTIL-electrolytes exhibit poor cyclability because electrochemical side reactions cause problematic surface failures of the cathode. Here, we demonstrate that a thin, homogeneous surface film, which is electrochemically generated on LiCoO2 from an RTIL-electrolyte containing an unsaturated substituent on the cation (1-allyl-1-methylpiperidinium bis(trifluoromethanesulfonyl)imide, AMPip-TFSI), can avert undesired side reactions. The derived surface film comprised of a high amount of organic species from the RTIL cations homogenously covered LiCoO2 with a <25 nm layer and helped suppress unfavorable thermal reactions as well as electrochemical side reactions. The superior performance of the cell containing the AMPip-TFSI electrolyte was further elucidated by surface, electrochemical, and thermal analyses.

Allylic ionic liquid electrolyte-assisted electrochemical surface passivation of LiCoO2 for advanced, safe lithium-ion batteries

NASA Astrophysics Data System (ADS)

Mun, Junyoung; Yim, Taeeun; Park, Jang Hoon; Ryu, Ji Heon; Lee, Sang Young; Kim, Young Gyu; Oh, Seung M.

2014-08-01

Room-temperature ionic liquid (RTIL) electrolytes have attracted much attention for use in advanced, safe lithium-ion batteries (LIB) owing to their nonvolatility, high conductivity, and great thermal stability. However, LIBs containing RTIL-electrolytes exhibit poor cyclability because electrochemical side reactions cause problematic surface failures of the cathode. Here, we demonstrate that a thin, homogeneous surface film, which is electrochemically generated on LiCoO2 from an RTIL-electrolyte containing an unsaturated substituent on the cation (1-allyl-1-methylpiperidinium bis(trifluoromethanesulfonyl)imide, AMPip-TFSI), can avert undesired side reactions. The derived surface film comprised of a high amount of organic species from the RTIL cations homogenously covered LiCoO2 with a <25 nm layer and helped suppress unfavorable thermal reactions as well as electrochemical side reactions. The superior performance of the cell containing the AMPip-TFSI electrolyte was further elucidated by surface, electrochemical, and thermal analyses.

Sorbitol, Rubus fruit, and misconception.

PubMed

Lee, Jungmin

2015-01-01

It is unclear how the misunderstanding that Rubus fruits (e.g., blackberries, raspberries) are high in sugar alcohol began, or when it started circulating in the United States. In reality, they contain little sugar alcohol. Numerous research groups have reported zero detectable amounts of sugar alcohol in fully ripe Rubus fruit, with the exception of three out of 82 Rubus fruit samples (cloudberry 0.01 g/100 g, red raspberry 0.03 g/100 g, and blackberry 4.8 g/100 g(∗); (∗)highly unusual as 73 other blackberry samples contained no detectable sorbitol). Past findings on simple carbohydrate composition of Rubus fruit, other commonly consumed Rosaceae fruit, and additional fruits (24 genera and species) are summarised. We are hopeful that this review will clarify Rosaceae fruit sugar alcohol concentrations and individual sugar composition; examples of non-Rosaceae fruit and prepared foods containing sugar alcohol are included for comparison. A brief summary of sugar alcohol and health will also be presented. Published by Elsevier Ltd.

Effect of chloride ion on corrosion behavior of SUS316L-grade stainless steel in nitric acid solutions containing seawater components under γ-ray irradiation

NASA Astrophysics Data System (ADS)

Sano, Y.; Ambai, H.; Takeuchi, M.; Iijima, S.; Uchida, N.

2017-09-01

Concerning the Fukushima Daiichi nuclear power plant accident, we investigated the effect of chloride ion on the corrosion behavior of SUS316L stainless steel, which is a typical material for the equipment used in reprocessing, in HNO3 solution containing seawater components, including under γ-ray irradiation condition. Electrochemical and immersion tests were carried out using a mixture of HNO3 and artificial seawater (ASW). In the HNO3 solution containing high amounts of ASW, the cathodic current densities increased and uniform corrosion progressed. This might be caused by strong oxidants, such as Cl2 and NOCl, generated in the reaction between HNO3 and Cl- ions. The corrosion rate decreased with the immersion time at low concentrations of HNO3, while it increased at high concentrations. Under γ-ray irradiation condition, the corrosion rate decreased due to the suppression of the cathodic reactions by the reaction between the above oxidants and HNO2 generated by radiolysis.

Research of stimulants and anabolic steroids in dietary supplements.

PubMed

Baume, N; Mahler, N; Kamber, M; Mangin, P; Saugy, M

2006-02-01

The purpose of this study was to analyze the composition of 103 dietary supplements bought on the internet. The supplements were dispatched in four different categories according to their announced contents [creatine, prohormones, "mental enhancers" and branched chain amino acids (BCAA)]. All the supplements were screened for the presence of stimulants and main anabolic steroids parent compounds. At the same time, the research was focused on the precursors and metabolites of testosterone and nandrolone. The study pointed out three products containing an anabolic steroid, metandienone, in a very high amount. The ingestion of such products induced a high quantity of metandienone metabolites in urines that would be considered as a positive antidoping test. The results have also shown that one creatine product and three "mental enhancers" contained traces of hormones or prohormones not claimed on the labels and 14 prohormone products contained substances other than those indicated by the manufacturer. The oral intake of the creatine product revealed the presence of the two main nandrolone metabolites (19-norandrosterone and 19-noretiocholanolone) in urine.

Allylic ionic liquid electrolyte-assisted electrochemical surface passivation of LiCoO2 for advanced, safe lithium-ion batteries

PubMed Central

Mun, Junyoung; Yim, Taeeun; Park, Jang Hoon; Ryu, Ji Heon; Lee, Sang Young; Kim, Young Gyu; Oh, Seung M.

2014-01-01

Room-temperature ionic liquid (RTIL) electrolytes have attracted much attention for use in advanced, safe lithium-ion batteries (LIB) owing to their nonvolatility, high conductivity, and great thermal stability. However, LIBs containing RTIL-electrolytes exhibit poor cyclability because electrochemical side reactions cause problematic surface failures of the cathode. Here, we demonstrate that a thin, homogeneous surface film, which is electrochemically generated on LiCoO2 from an RTIL-electrolyte containing an unsaturated substituent on the cation (1-allyl-1-methylpiperidinium bis(trifluoromethanesulfonyl)imide, AMPip-TFSI), can avert undesired side reactions. The derived surface film comprised of a high amount of organic species from the RTIL cations homogenously covered LiCoO2 with a <25 nm layer and helped suppress unfavorable thermal reactions as well as electrochemical side reactions. The superior performance of the cell containing the AMPip-TFSI electrolyte was further elucidated by surface, electrochemical, and thermal analyses. PMID:25168309

Fluoroacetate content of some species of the toxic Australian plant genus, Gastrolobium, and its environmental persistence.

PubMed

Twigg, L E; King, D R; Bowen, L H; Wright, G R; Eason, C T

1996-01-01

Gas chromatography confirmed the relatively high concentrations of fluoroacetate found in toxic Gastrolobiums, a genus of indigenous Australian plants. Fluoroacetate concentration in these plants ranged from 0.1 to 3875 micrograms/g (ppm) dry weight, with young leaves and flowers containing the highest concentrations. However, there was considerable intrastand variation between individual plants of at least two species with coefficients of variation ranging from 94% to 129%. Despite the high concentrations of fluoroacetate in many species, only one of nine soil samples collected from beneath these plants contained fluoroacetate. None of the 16 water samples collected from nearby streams and catchment dams contained fluoroacetate. This suggests that fluoroacetate does not persist in this environment. Fluoroacetate was also found in the genus Nemcia, and very low levels of fluoroacetate (ng/g) were detected in the foodstuffs, tea and guar gum. The latter indicates that other plant species may produce biologically insignificant amounts of fluoroacetate.

Antioxidant and cytoprotective activities of extracts prepared from fruit and vegetable wastes and by-products.

PubMed

Kabir, Faisal; Tow, Wei Wei; Hamauzu, Yasunori; Katayama, Shigeru; Tanaka, Sachi; Nakamura, Soichiro

2015-01-15

In this study, fruit and vegetable wastes and by-products were tested for polyphenol content and their antioxidant activity. The highest content of polyphenols as assessed by the Folin-Ciocalteu assay was the hot-water extract of grape seed, followed by the ethanol extract of buckwheat hull. The highest antioxidant activity measured by 2,2-diphenyl-1-picryl-hydrazyl (DPPH) assays was also detected in the hot-water extract of grape seed, followed by the ethanol extract of immature prune. Most of samples showed protective effects against oxidative stress induced by 2,2'-azobis-(2-amidinopropane) dihydrochloride (AAPH) peroxyl radical generator in African monkey kidney (MA 104) cells. Samples containing high amounts of phenolics (more than 30 mg ChAE/g) generally showed high antioxidant activity and a protective effect against AAPH-induced oxidative stress. This study demonstrates that fruit and vegetable wastes and by-products are good sources of high amounts of phenolics with antioxidant properties. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mineralization and Expression of Col1a1-3.6GFP Transgene in Primary Dental Pulp Culture

PubMed Central

Balic, Anamaria; Rodgers, Barbara; Mina, Mina

2008-01-01

We have examined and compared the effects of various differentiation-inducing media on mineralization, cell morphology and expression of pOBCol3.6GFP (3.6-GFP) in primary dental pulp cultures derived from 3.6-GFP transgenic mice. Our results show that media containing ascorbic acid only could not induce mineralization in primary dental pulp cultures. On the other hand, media containing ascorbic acid and β-glycerophosphate induced formation of mineralized matrix-containing dentin. The amount of mineralized matrix was increased by addition of dexamethasone. Cells treated with ascorbic acid and β-glycerophosphate were fibroblast like and cells treated with dexamethasone were cuboidal. In all culture conditions, high levels of 3.6-GFP were expressed in areas of mineralization PMID:18781059

Molecular cloning of a novel receptor tyrosine kinase, tif, highly expressed in human ovary and testis.

PubMed

Dai, W; Pan, H; Hassanain, H; Gupta, S L; Murphy, M J

1994-03-01

Using a combination of polymerase chain reaction and conventional cDNA library screening approaches, we have cloned and characterized a putative receptor tyrosine kinase termed tif. The extracellular domain of tif has an immunoglobulin-like loop and a fibronectin type III structure. The intracellular domain contains a tyrosine kinase domain. Compared with ryk, a ubiquitously expressed receptor tyrosine kinase, tif expression is tissue-specific with human ovary and testis containing the highest amount of tif mRNA. Many other tested human tissues such as heart, liver, pancreas and thymus do not contain detectable levels of tif mRNA. The molecular cloning and characterization of tif cDNA will facilitate the identification of a potential ligand(s) for the putative receptor and the study of its biological role.

Phytoconstituents and Nutritional Properties of the Fruits of Eleutherococcus divaricatus and Eleutherococcus sessiliflorus: A Study of Non-European Species Cultivated in Poland

PubMed Central

Verpoorte, Robert; Khan, Inamullah; Nowak, Renata

2017-01-01

Eleutherococcus fruits have been consumed in Russia and Asia throughout the centuries. Currently, there is an increasing interest in these products by the community of Western Europe. Many people suffer from micronutrient deficiencies, known as malnutrition, which consequently influences body condition. The aim of this study was to investigate pharmaconutrition, proximate, mineral, and fatty acid composition, total phenolics content, and total flavonoids content of Eleutherococcus divaricatus and Eleutherococcus sessiliflorus fruits cultivated in Poland. Eleutherococcus divaricatus and E. sessiliflorus contain a high amount of protein and fibres (16.70% and 12.28%; 61.41% and 45.63%, resp.). The fruits were generally high in K (21 g/kg) and low in sodium (0.001 g/kg). In terms of fatty acid composition, both species had a high amount of monounsaturated fatty acids (54.84–57.95%) and polyunsaturated fatty acids (36.22–37.0%). Using LC-ESI-MS/MS, protocatechuic acid has been identified as the most abundant compound, ranging from 260 to 810 μg/100 g DE. Among flavonoids, hyperoside was found to be in the highest amount (120–780 μg/100 g DE). Considering a rich chemical composition of the fruits, a better understanding of their health benefits is important in order to increase their utility and to enrich dietary sources of health promoting compounds. Because of a high amount of protein and a low calorific value, the fruits should be considered food for vegans or vegetarians. PMID:28182104

Petroleum Sludge as gypsum replacement in cement plants: Its Impact on Cement Strength

NASA Astrophysics Data System (ADS)

Benlamoudi, Ali; Kadir, Aeslina Abdul; Khodja, Mohamed

2017-08-01

Due to high cost of cement manufacturing and the huge amount of resources exhaustion, companies are trying to incorporate alternative raw materials or by-products into cement production so as to produce alternative sustainable cement. Petroleum sludge is a dangerous waste that poses serious imparts on soil and groundwater. Given that this sludge contains a high percentage of anhydrite (CaSO4), which is the main component of gypsum (CaSO4.2H2O), it may play the same gypsum role in strength development. In this research, a total replacement of gypsum (100%) has been substituted by petroleum sludge in cement production and has led to an increase of 28.8% in UCS values after 28 curing days. Nevertheless, the burning of this waste has emitted a considerable amount of carbon monoxide (CO) gas that needs to be carefully considered prior to use petroleum sludge within cement plants.

Reverse isotope dilution method for determining benzene and metabolites in tissues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bechtold, W.E.; Sabourin, P.J.; Henderson, R.F.

1988-07-01

A method utilizing reverse isotope dilution for the analysis of benzene and its organic soluble metabolites in tissues of rats and mice is presented. Tissues from rats and mice that had been exposed to radiolabeled benzene were extracted with ethyl acetate containing known, excess quantities of unlabeled benzene and metabolites. Butylated hydroxytoluene was added as an antioxidant. The ethyl acetate extracts were analyzed with semipreparative reversed-phase HPLC. Isolated peaks were collected and analyzed for radioactivity (by liquid scintillation spectrometry) and for mass (by UV absorption). The total amount of each compound present was calculated from the mass dilution of themore » radiolabeled isotope. This method has the advantages of high sensitivity, because of the high specific activity of benzene, and relative stability of the analyses, because of the addition of large amounts of unlabeled carrier analogue.« less

Oxidation Resistance of Alloys from Nb-Si-Cr System for High Temperature Applications

DTIC Science & Technology

2013-01-02

higher education for undergraduate students while prepare the graduate students for professional careers in research (at one of the ONR facilities...generate interest in students to pursue higher education for undergraduate students while prepare the graduate students for professional careers in...reduces the amount of primary a significantly but still contains a rather coarser eutectic like microconstituent. A NbßSi (3-1 silicide ) silicide phase

Superalloys with improved weldability for high temperature applications

DOEpatents

Seth, Brij B.; George, Easo P.; Babu, Sudarsanum S.; Goodwin, Gene M.; David, Stanislaus A.; Moyer, Carol E.

2001-01-01

A cast nickel-base superalloy component (10) is made having a composition containing small amounts of both boron and zirconium which are effective in combination to provide increased weldability, where such alloy is adapted for welding by weld (18) to a second superalloy piece, where the two pieces are firmly bonded together and have a Sigmajig transverse stress value (16) greater than 137.9 million Newtons per square meter.

Effect of chromium and phosphorus on the physical properties of iron and titanium-based amorphous metallic alloy films

NASA Technical Reports Server (NTRS)

Distefano, S.; Rameshan, R.; Fitzgerald, D. J.

1991-01-01

Amorphous iron and titanium-based alloys containing various amounts of chromium, phosphorus, and boron exhibit high corrosion resistance. Some physical properties of Fe and Ti-based metallic alloy films deposited on a glass substrate by a dc-magnetron sputtering technique are reported. The films were characterized using differential scanning calorimetry, stress analysis, SEM, XRD, SIMS, electron microprobe, and potentiodynamic polarization techniques.

Estimating carbon and nitrogen pools in a forest soil: Influence of soil bulk density methods and rock content

Treesearch

Martin F. Jurgensen; Deborah S. Page-Dumroese; Robert E. Brown; Joanne M. Tirocke; Chris A. Miller; James B. Pickens; Min Wang

2017-01-01

Soils with high rock content are common in many US forests, and contain large amounts of stored C. Accurate measurements of soil bulk density and rock content are critical for calculating and assessing changes in both C and nutrient pool size, but bulk density sampling methods have limitations and sources of variability. Therefore, we evaluated the use of small-...

Polymer Based Highly Parallel Nanoscopic Sensors for Rapid Detection of Chemical and Biological Threats

DTIC Science & Technology

2007-09-18

Xuliang Han, PI of Brewer Science, Inc. Subcontract Center for Applied Science & Engineering Missouri State University 901 South National Avenue...Science an effective post-growth purification procedure was developed to reduce the amount of impurities, and several characterization techniques were...CNTs) contain a wide range of impurities from the growth process. At Brewer Science an effective post-growth purification procedure was developed to

Attraction and electroantennogram responses of male Mediterranean fruit fly to volatile chemicals from Persea, Litchi and Ficus wood.

PubMed

Niogret, Jerome; Montgomery, Wayne S; Kendra, Paul E; Heath, Robert R; Epsky, Nancy D

2011-05-01

Trimedlure is the most effective male-targeted lure for the Mediterranean fruit fly, Ceratitis capitata (Wiedemann). A similar response is elicited by plant substances that contain α-copaene, a naturally-occurring sesquiterpene. α-Copaene is a complex, highly-volatile, widely-distributed plant compound, and male C. capitata respond to material from both hosts (e.g., Litchi chinensis) and non-hosts (e.g., Ficus benjamina) that contain α-copaene. Avocado, Persea americana, recently was found to contain varying amounts of α-copaene in the bark and underlying cambial tissue. Short-range attraction bioassays and electroantennography (EAG) were used to quantify responses of sterile male C. capitata to samples of rasped wood from four avocado genotypes, L. chinensis, and F. benjamina. Gas chromatography-mass spectral (GC-MS) analysis was used to identify and quantify the major sesquiterpenes. Attraction and EAG amplitude were correlated, with L. chinensis eliciting the highest and F. benjamina the lowest responses. Responses to the avocado genotypes were intermediate, but varied among the four types. GC-MS identified 13 sesquiterpenes, including α-copaene, from all samples. Amounts of α-copaene in volatile collections from samples (3 g) ranged from 11.8 μg in L. chinensis to 0.09 μg in F. benjamina, which correlated with short-range attraction and EAG response. α-Copaene ranged from 8.0 to 0.8 μg in the avocado genotypes, but attraction and EAG responses were not correlated with the amount of α-copaene. Differences in enantiomeric structure of the α-copaene in the different genotypes and/or presence of additional sesquiterpenes may be responsible for the variation in male response. EAG responses were correlated with the amount of several other sesquiterpenes including α-humulene, and this compound elicited a strong antennal response when tested alone.

Phytodegradation potential of bisphenolA from aqueous solution by Azolla Filiculoides

PubMed Central

2014-01-01

Many organic hazardous pollutants such as bisphenolA (BPA) which are toxic and not easily biodegradable can concerns for environmental pollution worldwide. The objective of this study was to examine whether Azolla Filiculoides is able to remove BPA from aqueous solutions. In this study, the Azolla with different biomass (0.3, 0.6, 0.9, 1.2 g) has been cultured in solution that was contained 5, 10, 25 and 50 ppm BPA. Samples were collected every 2 days from all of containers. The analytical determination of BPA was performed by using of DR4000 uv-visible at λmax = 276 nm. The results indicated that Azolla has high ability to remove BPA from aqueous solutions. The BPA removal was 60-90%. The removal efficiency is increasing with decreasing of BPA concentration and increasing of biomass amount and vice versa. The removal efficiency was more than 90% when BPA concentration was 5 ppm and amount of biomass was 0.9gr. It is concluded that Azolla able remove BPA by Phytodegradation from the aqueous solutions. Since conventional methods of BPA removal need to high cost and energy, phytoremediation by Azolla as a natural treatment system can decrease those issues and it can be a useful and beneficial method to removal of BPA. PMID:24693863

Phytodegradation potential of bisphenolA from aqueous solution by Azolla Filiculoides.

PubMed

Zazouli, Mohammad Ali; Mahdavi, Yousef; Bazrafshan, Edris; Balarak, Davoud

2014-01-01

Many organic hazardous pollutants such as bisphenolA (BPA) which are toxic and not easily biodegradable can concerns for environmental pollution worldwide. The objective of this study was to examine whether Azolla Filiculoides is able to remove BPA from aqueous solutions. In this study, the Azolla with different biomass (0.3, 0.6, 0.9, 1.2 g) has been cultured in solution that was contained 5, 10, 25 and 50 ppm BPA. Samples were collected every 2 days from all of containers. The analytical determination of BPA was performed by using of DR4000 uv-visible at λmax = 276 nm. The results indicated that Azolla has high ability to remove BPA from aqueous solutions. The BPA removal was 60-90%. The removal efficiency is increasing with decreasing of BPA concentration and increasing of biomass amount and vice versa. The removal efficiency was more than 90% when BPA concentration was 5 ppm and amount of biomass was 0.9gr. It is concluded that Azolla able remove BPA by Phytodegradation from the aqueous solutions. Since conventional methods of BPA removal need to high cost and energy, phytoremediation by Azolla as a natural treatment system can decrease those issues and it can be a useful and beneficial method to removal of BPA.

Adhesive Properties of Cured Phenylethynyl Containing Imides

NASA Technical Reports Server (NTRS)

Jensen, Brian J.; Chang, Alice C.

1997-01-01

Considerable attention has been directed towards acetylene terminated oligomers over the last 20 years' and recent work has focused on phenylethynyl terminated imide (PETI) oligomers. These reactive oligomers possess several features which make them attractive candidates for use as composite matrices and adhesives. The phenylethynyl group can be readily incorporated into many different functionalized oligomers. The reactive oligomers possess relatively low melt viscosities and thermally cure without the evolution of volatile by-products. Once cured, they typically display high glass transition temperatures (Tgs), excellent solvent resistance and high mechanical properties. new modified phenylethynyl-terminated imide (LaRC MPEI) oligomers were synthesized at various molecular weights utilizing a small amount of trifunctional amine. As long as the amount of triamine is relatively small, this approach produces a mixture of linear, star-shaped and branched polymer chains that has lower melt and solution viscosity than an equivalent molecular weight linear phenylethynyl terminated imide oligomers. The work reported herein involves the synthesis and characterization of a copolymer using this approach and the preparation of blends utilizing a phenylethynyl containing reactive plasticizer of lower molecular weight called LaRC LV-121. The chemistry and properties of this new MPEI as well as some blends of MPEI with LV-121, are presented and compared to the linear version, LARC-PETI-5.

Effect of different packaging materials containing poly-[2-(tert-butylamino) methylstyrene] on the growth of spoilage and pathogenic bacteria on fresh meat.

PubMed

Dohlen, S; Braun, C; Brodkorb, F; Fischer, B; Ilg, Y; Kalbfleisch, K; Lorenz, R; Kreyenschmidt, M; Kreyenschmidt, J

2017-09-18

The objective of this study was to investigate the effect of novel antimicrobial packaging materials containing poly-[2-(tertbutylamino) methylstyrene] (poly(TBAMS)) on the growth of typical spoilage and pathogenic bacteria present on meat. The antimicrobial activity of materials containing different poly(TBAMS) concentrations was determined by comparing the bacterial counts on reference and sample materials at different temperatures and times and in the presence of meat components. Storage tests with poultry fillets and veal cutlets were conducted with samples vacuum packaged in the reference foil and foil containing 10% poly(TBAMS). After specific time intervals, typical spoilage microorganisms, total viable count (TVC), sensory changes and pH value were analysed. The results of the different poly(TBAMS) containing packaging materials showed an increase of the antimicrobial activity with an increasing amount of poly(TBAMS) in the base polymer. A high antimicrobial activity against inoculum of spoilage and pathogenic organisms typical for meat products was detected of a multilayer foil containing 10% poly(TBAMS) in the inner layer after 24h at 7°C. Gram positive-bacteria were more sensitive to poly(TBAMS) foil than gram-negative bacteria. In storage tests however, over the entire storage, a significant effect of this poly(TBAMS) foil on microbial growth on chicken breast fillets and veal cutlets could not be identified. Poly(TBAMS) packaging materials showed very good antimicrobial properties against a wide range of bacteria. However, for a significant inhibition of microbial growth on fresh meat, a higher amount of poly(TBAMS) was necessary to prolong the shelf life of meat. Copyright © 2017 Elsevier B.V. All rights reserved.

High Temperature Sorbents for Oxygen

NASA Technical Reports Server (NTRS)

Sharma, Pramod K. (Inventor)

1996-01-01

A sorbent capable of removing trace amounts of oxygen (ppt) from a gas stream at a high temperature above 200 C is introduced. The sorbent comprises a porous alumina silicate support such as zeolite containing from 1 to 10 percent by weight of ion exchanged transition metal such as copper or cobalt ions and 0.05 to 1.0 percent by weight of an activator selected from a platinum group metal such as platinum. The activation temperature, oxygen sorption and reducibility are all improved by the presence of the platinum activator.

Image reconstruction of muon tomographic data using a density-based clustering method

NASA Astrophysics Data System (ADS)

Perry, Kimberly B.

Muons are subatomic particles capable of reaching the Earth's surface before decaying. When these particles collide with an object that has a high atomic number (Z), their path of travel changes substantially. Tracking muon movement through shielded containers can indicate what types of materials lie inside. This thesis proposes using a density-based clustering algorithm called OPTICS to perform image reconstructions using muon tomographic data. The results show that this method is capable of detecting high-Z materials quickly, and can also produce detailed reconstructions with large amounts of data.

Microbial solubilization of coals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, J.A.; Fredrickson, J.K.; Stewart, D.L.

1988-11-01

Microbial solubilization of coal may serve as a first step in a process to convert low-rank coals or coal-derived products to other fuels or products. For solubilization of coal to be an economically viable technology, a mechanistic understanding of the process is essential. Leonardite, a highly oxidized, low-rank coal, has been solubilized by the intact microorganism, cell-free filtrate, and cell-free enzyme of /ital Coriolus versicolor/. A spectrophotometric conversion assay was developed to quantify the amount of biosolubilized coal. In addition, a bituminous coal, Illinois No. 6, was solubilized by a species of /ital Penicillium/, but only after the coal hadmore » been preoxidized in air. Model compounds containing coal-related functionalities have been incubated with the leonardite-degrading fungus, its cell-free filtrate, and purified enzyme. The amount of degradation was determined by gas chromatography and the degradation products were identified by gas chromatography/mass spectrometry. We have also separated the cell-free filtrate of /ital C. versicolor/ into a <10,000 MW and >10,000 MW fraction by ultrafiltration techniques. Most of the coal biosolubilization activity is contained in the <10,000 MW fraction while the model compound degradation occurs in the >10,000 MW fraction. The >10,000 MW fraction appears to contain an enzyme with laccase-like activity. 10 refs., 8 figs., 5 tabs.« less

Bioactivity of Sodium Free Fluoride Containing Glasses and Glass-Ceramics

PubMed Central

Chen, Xiaojing; Chen, Xiaohui; Brauer, Delia S.; Wilson, Rory M.; Hill, Robert G.; Karpukhina, Natalia

2014-01-01

The bioactivity of a series of fluoride-containing sodium-free calcium and strontium phosphosilicate glasses has been tested in vitro. Glasses with high fluoride content were partially crystallised to apatite and other fluoride-containing phases. The bioactivity study was carried out in Tris and SBF buffers, and apatite formation was monitored by XRD, FTIR and solid state NMR. Ion release in solutions has been measured using ICP-OES and fluoride-ion selective electrode. The results show that glasses with low amounts of fluoride that were initially amorphous degraded rapidly in Tris buffer and formed apatite as early as 3 h after immersion. The apatite was identified as fluorapatite by 19F MAS-NMR after 6 h of immersion. Glass degradation and apatite formation was significantly slower in SBF solution compared to Tris. On immersion of the partially crystallised glasses, the fraction of apatite increased at 3 h compared to the amount of apatite prior to the treatment. Thus, partial crystallisation of the glasses has not affected bioactivity significantly. Fast dissolution of the amorphous phase was also indicated. There was no difference in kinetics between Tris and SBF studies when the glass was partially crystallised to apatite before immersion. Two different mechanisms of apatite formation for amorphous or partially crystallised glasses are discussed. PMID:28788139

[Origin of sennosides in health teas including Malva leaves].

PubMed

Kojima, T; Kishi, M; Sekita, S; Satake, M

2001-06-01

The aim of this study is to clarify whether sennosides are contained in the leaf of Malva verticillata L., and then to clarify the source of sennosides in health teas including malva leaves. The identification and determination of sennosides were performed with thin layer chromatography and high performance liquid chromatography. The leaf of Malva verticillata L. did not contain sennosides A or B and could be easily distinguished from senna leaf. Our previous report showed that sennosides are contained in weight-reducing herbal teas including malva leaves, and that senna leaf is a herbal component in some teas. Furthermore, in 10 samples of health tea including malva leaves that were bought last year, the smallest amount of sennosides was 6.1 mg/bag, and all health teas including malva leaves contained the leaf and midrib of senna. We suggest that sennosides A and B are not contained in the leaf of Malva verticillata L., and that the sennosides in health teas including malva leaves are not derived from malva leaf but from senna leaf.

Nitrogen fixation system of tungsten-resistant mutants of Azotobacter vinelandii.

PubMed Central

Riddle, G D; Simonson, J G; Hales, B J; Braymer, H D

1982-01-01

Mutants of Azotobacter vinelandii ATCC 12837 were isolated which could fix N2 in the presence of high tungsten concentrations. The most studied of these mutants (WD2) grew well in N-free modified Burk broth containing 10 mM W, whereas the wild type would not grow in this medium. WD2 would also grow in Burk N-free broth at about the same rate as the wild type. WD2 in broth containing W exhibited 22% of the whole cell acetylene reduction activity of the wild type in broth containing Mo and showed a lowered affinity for acetylene. Two-dimensional gel electrophoresis experiments showed that N2-fixing cells of WD2 from broth containing W or Mo did not produce significant amounts of component I of native nitrogenase protein. Electron spin resonance spectra of whole cells and cell-free extracts of WD2 from broth containing W lacked any trace of the g = 3.6 resonance associated with FeMoCo. Images PMID:6956567

Biotic and abiotic dynamics of a high solid-state anaerobic digestion box-type container system.

PubMed

Walter, Andreas; Probst, Maraike; Hinterberger, Stephan; Müller, Horst; Insam, Heribert

2016-03-01

A solid-state anaerobic digestion box-type container system for biomethane production was observed in 12 three-week batch fermentations. Reactor performance was monitored using physico-chemical analysis and the methanogenic community was identified using ANAEROCHIP-microarrays and quantitative PCR. A resilient community was found in all batches, despite variations in inoculum to substrate ratio, feedstock quality, and fluctuating reactor conditions. The consortia were dominated by mixotrophic Methanosarcina that were accompanied by hydrogenotrophic Methanobacterium, Methanoculleus, and Methanocorpusculum. The relationship between biotic and abiotic variables was investigated using bivariate correlation analysis and univariate analysis of variance. High amounts of biogas were produced in batches with high copy numbers of Methanosarcina. High copy numbers of Methanocorpusculum and extensive percolation, however, were found to negatively correlate with biogas production. Supporting these findings, a negative correlation was detected between Methanocorpusculum and Methanosarcina. Based on these results, this study suggests Methanosarcina as an indicator for well-functioning reactor performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

Novel anisole mixture and gasoline containing the same

DOEpatents

Singerman, Gary M.

1982-01-26

A novel anisole mixture containing anisole and a mixture of alkyl anisoles and liquid hydrocarbon fuels containing said novel anisole mixture in an amount sufficient to increase the octane number of said liquid fuel composition.

On the Role of High Amounts of Mn Element in CdS Structure

NASA Astrophysics Data System (ADS)

Gonullu, Meryem Polat; Kose, Salih

2017-03-01

CdS and MnS are technologically important semiconducting materials. In this work, due to the limited ability of these materials separately, a detailed characterization of the new samples formed by the combined use of them has been reported. CdS films, with the incorporation of Mn in a wide range of concentrations, have been produced by a low-cost Ultrasonic Spray Pyrolysis set-up. Spectroscopic Ellipsometry (SE) has been used to determine the thicknesses and optical constants ( n, k) of the samples. It has been determined that samples with high amounts of Mn have lower refractive index values. Absorbance spectra have shown additional band edges along with the one belonging to CdS, for samples with Mn concentrations higher than 50 pct. This has been attributed to a phase separation above this limit. Raman spectroscopy analysis which shows additional Raman peaks belonging to MnS phase also supports these findings. Depending on this phase separation, crystalline structure has been deteriorated. Surface properties of the samples have been investigated by SEM and AFM. Elemental analysis has been performed by EDS. Resistivity measurements performed by a four-probe set-up have shown that samples containing high amount of Mn have lower electrical resistivity values.

Fabrication of highly dense SiN4 ceramics without additives by high pressure sintering

NASA Technical Reports Server (NTRS)

Takatori, K.; Shimade, M.; Koizumi, M.

1984-01-01

Silicon nitride (Si3N4) is one of candidate materials for the engineering ceramics which is used at high temperatures. The mechanical strengths of hot pressed or sintered Si2N4 ceramics containing some amount of additives, however, are deteriorated at elevated temperatures. To improve the high temperature strength of Si3N4 ceramics, an attempt to consolidate Si3N4 without additives was made by high pressure sintering technique. Scanning electron micrographs of fracture surfaces of the sintered bodies showed the bodies had finely grained and fully self-bonded sintered bodies were 310N sq m at room temperature and 174N/sq m at 1200 C.

An analysis of antioxidants, organoleptics and hedonics with variations of boiling time in Jasmine tea and Jasmine root tea a study on Kaliprau, Pemalang

NASA Astrophysics Data System (ADS)

Arifan, Fahmi; Winarni, Sri; Handoyo, Gentur; Nurdiana, Asri; Nabila Rahma H, Afkar; Risdiyanti, Sri

2018-05-01

There are so many jasmine plantations without any preservation and post production in Kaliprau, Pemalang. The aims of this research are analyzing the amount of antioxidant and organoleptic-hedonic test. The measurement of antioxidant used in this research is using DPPH. The organoleptic and hedonic test on 25 respondents. Jasmines that been used on this research are the flower and the root part. Through the test, some results have been found from the jasmine tea’s sampling with the boiling time of 15 minutes and it contain antioxidant for about 55.0% and 74.84% for the jasmine root tea. Whereas for the boiling time of 30 minutes, it contained 54.00% of antioxidant for the jasmine tea and 84.00% of antioxidant in jasmine root tea. Jasmine tea and jasmine root tea contains flavonoids. Despite the large amount of antioxidant were found in jasmine tea and jasmine root tea (50-100%). There’s a decreasing of antioxidant amount found in the samples, along with the prolonged boiling time. 84% of tresponden like the scent, flavor, color and the texture of jasmine tea and jasmine root tea. These products are finally accepted by the people and have its large amount of antioxidant contain for the jasmine tea.

Assessment of two thermally treated drill mud wastes for landfill containment applications.

PubMed

Carignan, Marie-Pierre; Lake, Craig B; Menzies, Todd

2007-10-01

Offshore oil and gas drilling operations generate significant amounts of drill mud waste, some of which is transported onshore for subsequent thermal treatment (i.e. via thermal remediation). This treatment process results in a mineral waste by-product (referred to as thermally treated drill mud waste; TTDMW). Bentonites are originally present in many of the drill mud products and it is hypothesized that TTDMW can be utilized in landfill containment applications (i.e. cover or base liner). The objective of this paper is to examine the feasibility of this application by performing various physical and chemical tests on two TTDMW samples. It is shown that the two TTDMW samples contained relatively small amounts of clay-sized minerals although hydraulic conductivity values are found to be less than 10(-8) m/s. Organic carbon contents of the samples were approximately 2%. Mineralogy characterization of the samples confirmed varying amounts of smectite, however, peak friction angles for a TTDMW sample was greater than 36 degrees. Chemical characterization of the TTDMW samples show potential leaching of barium and small amounts of other heavy metals. Discussion is provided in the paper on suggestions to assist in overcoming regulatory issues associated with utilization of TTDMW in landfill containment applications.

[Changes in nutritional recommendations for a healthy population and their influence on a diabetic diet].

PubMed

Anděl, Michal; Brunerová, Ludmila; Dlouhý, Pavel; Polák, Jan; Gojda, Jan; Kraml, Pavel

Recently, thousands of papers brought knowledge about effects of nutrients on cellular level, in experimental animals and in human experiments on one side, the results of epidemiological studies on the other side have suggested the nutrients and foods for healthy diet and nutrients and foods, which should be consumed only in limited amount. Among foods, which should be avoided, those with higher content of trans-fatty acids. Their daily intake should not exceed 1 % of total energy intake. Similar should be limited saturated fatty acid, added sugar and salt. On the contrary, the intake of monounsaturated and polyunsaturated fatty acids in foods should be basic part of fat intake. In these conditions the amount of consumed fat could create up to 35 % of all daily energy intake. Beneficial carbohydrates are those with low glycemic index, i.e. whole grain and brown rice products and legumes. The intake of salt is necessary to limit fewer than 6 g per day and alcohol intake should not exceed 10 g per day in women and 20 g per day in men. The recommendation in last years do not limit cholesterol daily intake. The food of animal origin with high content of saturated fatty acids, i.e. meat and milk products parallel contains also cholesterol. On the other hand, the oils of vegetable origin mostly from tropical oils, which contents high amount of saturated fatty acids represents the risk? On the contrary eggs and shellfish contents high amount of cholesterol and very low amounts of saturated fatty acids. Therefore, there is no reason for their strict limitation in the diet. carbohydrate - diabetes - dietary recommendation - energy intake - fat - healthy diet - iron - cholesterol - protein.

High concentrations of fluoride and boron in drinking water wells in the Muenster region--results of a preliminary investigation.

PubMed

Queste, A; Lacombe, M; Hellmeier, W; Hillermann, F; Bortulussi, B; Kaup, M; Ott, K; Mathys, W

2001-03-01

In 1998, two cases of severe dental fluorosis in schoolchildren occurred in the Muenster region. These cases took place in one household, where fluoridated toothpaste, fluoridated salt, and fluoride tablets were consumed. Furthermore, the family used drinking water from its private well only. Analyses of the well water ordered by local health officials revealed very high amounts of fluoride, boron, and other electrolytes. This unusual combination of high amounts of fluoride and boron could also be found in the water of a great number of other private wells that are the only source for drinking water in this rural region of the Muensterland. Anthropogenic sources could be excluded. Because of this, the results of the water samples were collated to the specific geological situation in this area. In the Muenster region there are marl layers of the chalk era covered with quarternary sediments. The quarternary sediments are up to 10 to 20 metres thick and they usually conduct the groundwater. The marl contains high concentrations of fluoride and boron. In some places the groundwater has contact with these layers. To check the amount of fluoride and boron in the groundwater, indicator values were sought, which can give a hint of high contents of these trace elements. In this study the conductivity and acidity were identified as possible indicators of a high amount of fluoride and boron in the drinking water in this specific region. To work economically and efficiently, the drinking water should be checked for fluoride and boron on a regular basis only when these values are extraordinarily high. In the case of high concentrations, especially of fluoride, in the drinking water the persons concerned should be informed about their potential health risk, giving them the opportunity to optimise the total daily intake of fluoride.

Evidence for hydrous high-MgO melts in the Precambrian

NASA Astrophysics Data System (ADS)

Stone, William E.; Deloule, Etienne; Larson, Michelle S.; Lesher, C. Michael

1997-02-01

Prevailing petrogenetic models for Precambrian high-MgO melts such as komatiites invoke crystallization from nearly anhydrous melts (≪0.5% H2O) generated by partial melting of mantle peridotite at temperatures of (≤ 1900 °C and pressures of (18 GPa. However, ultramafic cumulate and gabbro zones of komatiitic and other high-MgO units in Precambrian greenstone belts contain vesicles and minor to major amounts (≤ 25%) of igneous amphibole. The textures (oikocrysts, rims on intercumulate pyroxene, and mineral inclusions within orthocumulate olivine) and the water-rich compositions (1.00% 2.50% H2O) of igneous amphiboles from the Archean Abitibi belt indicate crystallization in situ from significantly hydrous melts while the melt fraction was still as high as 40% 50%. Comparisons to experimental phase equilibria suggest that the residual melts from which the amphiboles crystallized contained 3% 4% H2O, and adjustments for fractional crystallization suggest that the initial melts may have contained as much as 2% H2O. H2O contents of this magnitude would require substantial revision of the nearly anhydrous models for Precambrian high-MgO melts, possibly permitting generation at lower temperatures and pressures, lowering their densities and viscosities, increasing their eruptibility, and enhancing the formation of spinifex textures.

Chitosan-aluminum monostearate composite sponge dressing containing asiaticoside for wound healing and angiogenesis promotion in chronic wound.

PubMed

Phaechamud, Thawatchai; Yodkhum, Kotchamon; Charoenteeraboon, Juree; Tabata, Yasuhiko

2015-05-01

There are many factors that delay healing in chronic wounds including lowering level of growth factors and increasing exudate level comprising high amount of tissue destructive enzymes. Asiaticoside possesses interesting wound healing and angiogenic activities that are employed to stimulate tissue regeneration in wound healing application. This study attempted to develop chitosan-aluminum monostearate (Alst) composite sponge containing asiaticoside for use as an absorbent medical dressing in chronic wound. N-methyl-2-pyrrolidone (NMP) was used to enhance homogeneity of asiaticoside in the polymer composite matrix. The sponge dressings were prepared by lyophilization and dehydrothermal treatment (DHT). Functional group interaction, crystallinity, and morphology of the prepared sponges were investigated using FT-IR, PXRD, and SEM, respectively. Physicochemical properties, porosity, hydrophilic/hydrophobic properties and mechanical property, were evaluated. Wound dressing properties, water vapor transmission rate (WVTR), fluid absorbency, oxygen permeation (OP), and bio-adhesive property, were investigated. In vitro asiaticoside release study was conducted using immersion method. Cytotoxicity was studied in normal human dermal fibroblast (NHDF) and normal human epidermal keratinocyte (NHEK). Angiogenic activity of asiaticoside was evaluated using chick-chorioallantoic membrane (CAM) assay. FT-IR and PXRD results revealed the amidation after DHT to enhance the crystallinity of the prepared sponges. The prepared sponges had high porosity comprising high Alst-loaded amount that exhibited more compact structure. Alst enhanced hydrophobicity therefore it reduced the fluid absorption and WVTR together with bio-adhesion of the prepared sponge dressings. Porosity of all sponges was more than 85% therefore resulting in their high OP. Enhancing hydrophobicity of the material by Alst and more homogeneity caused by NMP eventually retarded the asiaticoside release for 7 days. The sponge extractions were non-toxic to the cells moreover they promoted NHDF and NHEK cell proliferation. Asiaticoside and asiaticoside-contained dressings exhibited dose-dependent angiogenic activity in CAM model. Copyright © 2015 Elsevier B.V. All rights reserved.

Quantitative determination of fatty acids in marine fish and shellfish from warm water of Straits of Malacca for nutraceutical purposes.

PubMed

Abd Aziz, Nurnadia; Azlan, Azrina; Ismail, Amin; Mohd Alinafiah, Suryati; Razman, Muhammad Rizal

2013-01-01

This study was conducted to quantitatively determine the fatty acid contents of 20 species of marine fish and four species of shellfish from Straits of Malacca. Most samples contained fairly high amounts of polyunsaturated fatty acids (PUFAs), especially alpha-linolenic acid (ALA, C18:3 n3), eicosapentaenoic acid (EPA, C20:5 n3), and docosahexaenoic acid (DHA, C22:6 n3). Longtail shad, yellowstripe scad, and moonfish contained significantly higher (P < 0.05) amounts of eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and alpha-linolenic acid (ALA), respectively. Meanwhile, fringescale sardinella, malabar red snapper, black pomfret, Japanese threadfin bream, giant seaperch, and sixbar grouper showed considerably high content (537.2-944.1 mg/100 g wet sample) of desirable omega-3 fatty acids. The polyunsaturated-fatty-acids/saturated-fatty-acids (P/S) ratios for most samples were higher than that of Menhaden oil (P/S = 0.58), a recommended PUFA supplement which may help to lower blood pressure. Yellowstripe scad (highest DHA, ω - 3/ω - 6 = 6.4, P/S = 1.7), moonfish (highest ALA, ω - 3/ω - 6 = 1.9, P/S = 1.0), and longtail shad (highest EPA, ω - 3/ω - 6 = 0.8, P/S = 0.4) were the samples with an outstandingly desirable overall composition of fatty acids. Overall, the marine fish and shellfish from the area contained good composition of fatty acids which offer health benefits and may be used for nutraceutical purposes in the future.

Quantitative Determination of Fatty Acids in Marine Fish and Shellfish from Warm Water of Straits of Malacca for Nutraceutical Purposes

PubMed Central

Abd Aziz, Nurnadia; Azlan, Azrina; Ismail, Amin; Mohd Alinafiah, Suryati; Razman, Muhammad Rizal

2013-01-01

This study was conducted to quantitatively determine the fatty acid contents of 20 species of marine fish and four species of shellfish from Straits of Malacca. Most samples contained fairly high amounts of polyunsaturated fatty acids (PUFAs), especially alpha-linolenic acid (ALA, C18:3 n3), eicosapentaenoic acid (EPA, C20:5 n3), and docosahexaenoic acid (DHA, C22:6 n3). Longtail shad, yellowstripe scad, and moonfish contained significantly higher (P < 0.05) amounts of eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and alpha-linolenic acid (ALA), respectively. Meanwhile, fringescale sardinella, malabar red snapper, black pomfret, Japanese threadfin bream, giant seaperch, and sixbar grouper showed considerably high content (537.2–944.1 mg/100g wet sample) of desirable omega-3 fatty acids. The polyunsaturated-fatty-acids/saturated-fatty-acids (P/S) ratios for most samples were higher than that of Menhaden oil (P/S = 0.58), a recommended PUFA supplement which may help to lower blood pressure. Yellowstripe scad (highest DHA, ω − 3/ω − 6 = 6.4, P/S = 1.7), moonfish (highest ALA, ω − 3/ω − 6 = 1.9, P/S = 1.0), and longtail shad (highest EPA, ω − 3/ω − 6 = 0.8, P/S = 0.4) were the samples with an outstandingly desirable overall composition of fatty acids. Overall, the marine fish and shellfish from the area contained good composition of fatty acids which offer health benefits and may be used for nutraceutical purposes in the future. PMID:23509703

Mechanochemical pre-treatment for viable recycling of plastic waste containing haloorganics.

PubMed

Cagnetta, Giovanni; Zhang, Kunlun; Zhang, Qiwu; Huang, Jun; Yu, Gang

2018-05-01

Chemical recycling technologies are the most promising for a waste-to-energy/material recovery of plastic waste. However, 30% of such waste cannot be treated in this way due to the presence of halogenated organic compounds, which are often utilized as flame retardants. In fact, high quantities of hydrogen halides and dioxin would form. In order to enabling such huge amount of plastic waste as viable feedstock for recycling, an investigation on mechanochemical pre-treatment by high energy ball milling is carried out on polypropylene containing decabromodiphenyl ether. Results demonstrate that co-milling with zero valent iron and quartz sand ensures complete debromination and mineralization of the flame retardant. Furthermore, a comparative experiment demonstrates that the mechanochemical debromination kinetics is roughly proportional to the polymer-to-haloorganics mass ratio. Copyright © 2018 Elsevier Ltd. All rights reserved.

Processing of oats and the impact of processing operations on nutrition and health benefits.

PubMed

Decker, Eric A; Rose, Devin J; Stewart, Derek

2014-10-01

Oats are a uniquely nutritious food as they contain an excellent lipid profile and high amounts of soluble fibre. However, an oat kernel is largely non-digestible and thus must be utilised in milled form to reap its nutritional benefits. Milling is made up of numerous steps, the most important being dehulling to expose the digestible groat, heat processing to inactivate enzymes that cause rancidity, and cutting, rolling or grinding to convert the groat into a product that can be used directly in oatmeal or can be used as a food ingredient in products such as bread, ready-to-eat breakfast cereals and snack bars. Oats can also be processed into oat bran and fibre to obtain high-fibre-containing fractions that can be used in a variety of food products.

Pressure waves in liquid mercury target from pulsed heat loads and the possible way controlling their effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ni, L.; Skala, K.

1996-06-01

In ESS project liquid metals are selected as the main target for the pulsed spallation neutron source. Since the very high instantaneous energy is deposited on the heavy molten target in a very short period time, pressure waves are generated. They travel through the liquid and cause high stress in the container. Also, additional stress should be considered in the wall which is the result of direct heating of the target window. These dynamic processes were simulated with computational codes with the static response being analized first. The total resulting dynamic wall stress has been found to have exceeded themore » design stress for the selected container material. Adding a small amount of gas bubbles in the liquid could be a possible way to reduce the pressure waves.« less

42 CFR 405.817 - Principles for determining amount in controversy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Principles for determining amount in controversy... the Medicare Part B Program § 405.817 Principles for determining amount in controversy. (a) Individual... may assert that the aggregation principles contained in this subpart may be applied to determine the...

20 CFR Appendixes to Subpart C of... - Note

Code of Federal Regulations, 2010 CFR

2010-04-01

... The following appendices contain data that are needed in computing primary insurance amounts. Appendix... begin to use the new data in computing primary insurance amounts as soon as required by law, even before we periodically update these appendices. If the data you need to find your primary insurance amount...

Diets with no or low amounts of dietary fiber can reduce small intestinal ulcers induced by non-steroidal anti-inflammatory drugs in dogs.

PubMed

Satoh, H; Kondo, R; Shinoda, T; Idaka, S; Ishigami, K; Shiotani, S

2016-08-01

Recent progress in endoscopic techniques has revealed that non-steroidal anti-inflammatory drugs (NSAIDs) often cause ulcers in the small intestine in humans, but effective therapy is not available at present. In the present study, we investigated the effects of feeding condition and the amount of dietary fiber (DF) in the diet on the formation of gastrointestinal ulcers induced by NSAIDs in dogs. Several types of diets containing various percentages of DF were given to dogs. Indomethacin (1 or 3 mg/kg, p.o.), ketoprofen (2 mg/kg, s.c.), or fulnixin (1 mg/kg, s.c.) was administered once daily at 10 a.m. after a morning meal or without a morning meal (fasted condition) for 3 - 7 days. Gastrointestinal lesions were examined 24 h after the final dose of the drugs. When indomethacin (3 mg/kg) was administered after a morning meal (fed condition) for 7 days, it produced many lesions in the small intestine. However, when it was given in the fasted condition without the morning meal, the lesions were markedly decreased. All the NSAIDs given after feeding of regular dry food containing 6% DF once a day for 3 days produced many lesions in the small intestine. The lesions were decreased or increased in dogs given prescription diets containing low DF (1.1%) and high DF (15.4%), respectively. Furthermore, lesions were not observed in dogs given canned diet containing very low DF (< 0.1%), whereas lesions appeared again in dogs given canned diet supplemented with cellulose (3 or 10%) but not with pectin (10%). These results suggested that both feeding condition and insoluble DF, such as cellulose in the diet, play an important role in the formation of NSAID-induced small intestinal lesions, and that a diet with no or low amounts of DF may decrease gastrointestinal side-effects associated with the use of NSAIDs.

Mineralization of Basalts in the CO 2-H 2O-H 2S System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; McGrail, B. Peter; Owen, Antionette T.

2013-05-10

Basalt samples representing five different formations were immersed in water equilibrated with supercritical carbon dioxide containing 1% hydrogen sulfide (H2S) at reservoir conditions (100 bar, 90°C) for up to 3.5 years. Surface coatings in the form of pyrite and metal cation substituted carbonates were identified as reaction products associated with all five basalts. In some cases, high pressure tests contained excess H2S, which produced the most corroded basalts and largest amount of secondary products. In comparison, tests containing limited amounts of H2S appeared least reacted with significantly less concentrations of reaction products. In all cases, pyrite appeared to precede carbonation,more » and in some instances, was observed in the absence of carbonation such as in cracks, fractures, and within the porous glassy mesostasis. Armoring reactions from pyrite surface coatings observed in earlier shorter duration tests were found to be temporary with carbonate mineralization observed with all the basalts tested in these long duration experiments. Geochemical simulations conducted with the geochemical code EQ3/6 accurately predicted early pyrite precipitation followed by formation of carbonates. Reactivity with H2S was correlated with measured Fe(II)/Fe(III) ratios in the basalts with more facile pyrite formation occurring with basalts containing more Fe(III) phases. These experimental and modeling results confirm potential for long term sequestration of acid gas mixtures in continental flood basalt formations.« less

The three subtypes of atrial natriuretic peptide (ANP) receptors are expressed in the rat adrenal gland.

PubMed

Grandclément, B; Ronsin, B; Morel, G

1997-03-01

Atrial natriuretic peptide (ANP) actions are mediated by highly selective and specific receptors. Three subtypes have been characterized and cloned: ANP receptor-A (or GC-A), -B (or GC-B) and -C (the so-called clearance receptor). In rat adrenal gland, the mRNA for each subtype was detected using 35S-dUTP or digoxigenin-11-dUTP specific labeled probes, and in situ hybridization at light and electron microscopic levels respectively. The three subtypes were expressed the most abundantly in the zona glomerulosa. The amount of GC-A mRNA expression, quantified using macro-autoradiography and densitometry, was higher than the amounts of GC-B mRNA and ANPR-C mRNA both in zona glomerulosa and medullary of adrenal gland. At electron microscopic level, the three subtypes of ANPR were revealed in glomerulosa cells. A noticeable signal was also present in the medullary area, especially for GC-A mRNA, in adrenaline-containing chromaffin cells. No signal was detected in noradrenaline-containing chromaffin cells. The subcellular localization of the three mRNAs is similar: in the cytoplasmic matrix and in the euchromatin of the nucleus in each cell of glomerulosa, and in the same compartments of the adrenaline-containing chromaffin cells. These data indicate that the adrenal gland is an important target tissue for ANP action both in glomerulosa cells and adrenaline-containing chromaffin cells. The mRNA expression levels were different for each ANPR subtype.

Aluminum elution and precipitation in glass vials: effect of pH and buffer species.

PubMed

Ogawa, Toru; Miyajima, Makoto; Wakiyama, Naoki; Terada, Katsuhide

2015-02-01

Inorganic extractables from glass vials may cause particle formation in the drug solution. In this study, the ability of eluting Al ion from borosilicate glass vials, and tendencies of precipitation containing Al were investigated using various pHs of phosphate, citrate, acetate and histidine buffer. Through heating, all of the buffers showed that Si and Al were eluted from glass vials in ratios almost the same as the composition of borosilicate glass, and the amounts of Al and Si from various buffer solutions at pH 7 were in the following order: citrate > phosphate > acetate > histidine. In addition, during storage after heating, the Al concentration at certain pHs of phosphate and acetate buffer solution decreased, suggesting the formation of particles containing Al. In citrate buffer, Al did not decrease in spite of the high elution amount. Considering that the solubility profile of aluminum oxide and the Al eluting profile of borosilicate glass were different, it is speculated that Al ion may be forced to leach into the buffer solution according to Si elution on the surface of glass vials. When Al ions were added to the buffer solutions, phosphate, acetate and histidine buffer showed a decrease of Al concentration during storage at a neutral range of pHs, indicating the formation of particles containing Al. In conclusion, it is suggested that phosphate buffer solution has higher possibility of forming particles containing Al than other buffer solutions.

Effect of dietary fish oil supplements alone or in combination with sunflower and linseed oil on ruminal lipid metabolism and bacterial populations in lactating cows.

PubMed

Kairenius, P; Leskinen, H; Toivonen, V; Muetzel, S; Ahvenjärvi, S; Vanhatalo, A; Huhtanen, P; Wallace, R J; Shingfield, K J

2018-04-01

Fish oil (FO) alters ruminal biohydrogenation causing trans fatty acid (FA) intermediates to accumulate, but the effects of 18-carbon polyunsaturated FA supply on ruminal long-chain FA metabolism and microbial communities in cattle fed FO are not well established. Four cows fitted with rumen cannula were used in a 4 × 4 Latin square with 21-d experimental periods to evaluate the effects of FO alone or in combination with plant oils high in 18:2n-6 or 18:3n-3 on rumen microbial ecology and flow of FA at the omasum. Treatments comprised a basal grass silage-based diet containing no additional oil (control) or supplements of FO (200 g/d) or FO (200 g/d) plus 500 g/d of sunflower oil (SFO) or linseed oil (LFO). Flow of FA was determined using the omasal sampling technique. The relative abundance of key biohydrogenating bacteria was assessed by quantitative PCR on 16S rRNA genes in omasal digesta. Fish oil-supplemented treatments increased the amounts of trans-18:1, trans-18:2, and 20- to 22-carbon polyunsaturated FA escaping the rumen. Relative to the control, oil supplements had no effect on the amount of 18:0 leaving the rumen, but LFO decreased the flow of 18:0 at the omasum compared with SFO. Both SFO and LFO increased trans-18:1 relative to FO, whereas LFO resulted in the highest trans-18:2 and 20- to 22-carbon FA flow. Supplements of FO plus plant oils shifted biohydrogenation toward trans-10 18:1 formation. Compared with FO alone, the ruminal metabolism of 22:6n-3 in the rumen of lactating cows is more extensive on diets containing higher amounts of 18-carbon polyunsaturated FA. However, the biohydrogenation of 22:5n-3 was less extensive in LFO than SFO, but showed no difference between FO and diets containing plant oils. Ruminal outflow of 20:5n-3 was not altered when plant oils were added to FO. Alterations in the amount of intermediates at the omasum or ruminal biohydrogenation pathways were not accompanied by major changes in analyzed bacterial populations. In conclusion, dietary supplements of FO alone or in combination with plant oils increase the amount of biohydrogenation intermediates containing 1 or more trans double bonds escaping the rumen, which may have implications for host metabolism and the nutritional quality of ruminant foods. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Amino acid composition in determination of collagen origin and assessment of physical factors effects.

PubMed

Gauza-Włodarczyk, Marlena; Kubisz, Leszek; Włodarczyk, Dariusz

2017-11-01

The amino acid composition of collagen is a characteristic feature of this protein. Collagen, irrespective of its origin, contains 19 amino acids, including hydroxyproline which does not occur in other proteins. Its atypical amino acid composition is characterized by high content of proline and glycine, as well as the absence of cysteine. This paper shows the comparison of qualitative composition of amino acids of fish skin (FS) collagen, bovine Achilles tendon (BAT) collagen, and bone collagen. Results demonstrate that FS collagen as well as BAT collagen contains no cysteine and significantly different amount of hydroxyproline. In BAT collagen hydroxyproline content is 30% higher than hydroxyproline content of FS collagen. In bone collagen the amount of hydroxyproline is two times more than in FS collagen. Furthermore, it is shown that sensitivity to radiation of individual amino acids varies and depends on the absorbed dose of ionizing radiation. The changes observed in the amino acid composition become very intense for the doses of 500kGy and 1000kGy. Copyright © 2017 Elsevier B.V. All rights reserved.

Pollutant formation in the pyrolysis and combustion of materials combining biomass and e-waste.

PubMed

Soler, Aurora; Conesa, Juan A; Iñiguez, María E; Ortuño, Nuria

2018-05-01

Combustion and pyrolysis runs at 850°C were carried out in a laboratory scale horizontal reactor with different materials combining biomass and waste electrical and electronic equipment (WEEE). Analyses are presented of the carbon oxides, light hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), polychlorinated benzenes (ClBzs), polychlorinated phenols (ClPhs), polybrominated phenols (BrPhs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Results showed that gas emissions were mainly composed of CO and CO 2 ; the high level of CO found in the pyrolytic runs was easily transformed into CO 2 by reaction with oxygen. The total amount of light hydrocarbons emitted was higher in the samples containing WEEE, methane being the most abundant light hydrocarbon in all the runs. However, the presence of WEEE reduced the emission of PAHs which decreased with the increase of the oxygen. The total amount of BrPhs increased in the decomposition of the samples containing WEEE, reaching its maximum in pyrolysis runs. Emission of PCDD/Fs was enhanced in pyrolytic conditions and easily decreased in the presence of oxygen. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of processing on the release profiles of matrix systems containing 5-aminosalicylic acid.

PubMed

Korbely, Anita; Kelemen, András; Kása, Péter; Pintye-Hódi, Klára

2012-12-01

The aim of this study was to investigate the influence of different processing methods on the profiles of 5-aminosalicylic acid dissolution from controlled-release matrix systems based on Eudragit® RL and Eudragit® RS water-insoluble polymers. The pure polymers and their mixtures were studied as matrix formers using different processing methods, i.e., direct compression, wet granulation of the active ingredient with the addition of polymer(s) to the external phase, wet granulation with water, and wet granulation with aqueous dispersions. In comparison with the directly compressed tablets, tablets made by wet granulation with water demonstrated a 6-19% increase in final drug dissolution, whereas when polymers were applied in the external phase during compression, a 0-13% decrease was observed in the amount of drug released. Wet granulation with aqueous polymer dispersions delayed the release of the drug; this was especially marked (a 54-56% decrease in drug release) in compositions, which contained a high amount of Eudragit RL 30D. The release profiles were mostly described by the Korsmeyer-Peppas model or the Hopfenberg model.

Novel surface modification of polymer-based separation media controlling separation selectivity, retentivity and generation of electroosmotic flow.

PubMed

Hosoya, Ken; Kubo, Takuya; Takahashi, Katsuo; Ikegami, Tohru; Tanaka, Nobuo

2002-12-06

Uniformly sized packing materials based on synthetic polymer particles for high-performance liquid chromatography (HPLC) and capillary electrochromatography (CEC) have been prepared from polymerization mixtures containing methacrylic acid (MAA) as a functional monomer and by using a novel surface modification method. This "dispersion method" affords effectively modified separation media. Both the amount of MAA utilized in the preparation and reaction time affect the selectivity of chromatographic separation in both the HPLC and the CEC mode and electroosmotic flow. This detailed study revealed that the dispersion method effectively modified internal surface of macroporous separation media and, based on the amount of MAA introduced, exclusion mechanism for the separation of certain solutes could be observed.

Proximate composition, fatty acid analysis and protein digestibility-corrected amino acid score of three Mediterranean cephalopods.

PubMed

Zlatanos, Spiros; Laskaridis, Kostas; Feist, Christian; Sagredos, Angelos

2006-10-01

Proximate composition, fatty acid analysis and protein digestibility-corrected amino acid score (PDCAAS) in three commercially important cephalopods of the Mediterranean sea (cuttlefish, octopus and squid) were determined. The results of the proximate analysis showed that these species had very high protein:fat ratios similar to lean beef. Docosahexaenoic, palmitic and eicosipentaenoic acid were the most abundant fatty acids among analyzed species. The amount of n-3 fatty acids was higher than that of saturated, monounsaturated and n-6 fatty acids. Despite the fact that cephalopods contain small amounts of fat they were found quite rich in n-3 fatty acids. Finally, PDCAAS indicated that these organisms had a very good protein quality.

Investigation of the demulsification of water-in-oil emulsions formed when crude oil or fuel oil is spilt on the sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, M.A.

The highly viscous water-in-oil emulsions, formed when crude or fuel oil is spilt at sea, are difficult to collect, and expensive to transport as they contain 50 to 80% water. Laboratory experiments have been carried out to determine the factors to be considered in the demulsification of these emulsions. The important factors were found to be the choice and amount of demulsifier, the temperature, and the time amount of mixing during the addition of the demulsifier. These preliminary findings will be used to develop large-scale demulsification systems for use at sea and on the beach, during collection of the emulsions.more » (Copyright (c) Crown Copyright 1980.)« less

Post-consumer contamination in high-density polyethylene (HDPE) milk bottles and the design of a bottle-to-bottle recycling process.

PubMed

Welle, F

2005-10-01

Six hundred conventional recycled HDPE flake samples, which were recollected and sorted in the UK, were screened for post-consumer contamination levels. Each analysed sample consisted of 40-50 individual flakes so that the amount of analysed individual containers was in the range 24,000-30,000 post-consumer milk bottles. Predominant contaminants in hot-washed flake samples were unsaturated oligomers, which can be also be found in virgin high-density polyethylene (HDPE) pellet samples used for milk bottle production. In addition, the flavour compound limonene, the degradation product of antioxidant additives di-tert-butylphenol and low amounts of saturated oligomers were found in higher concentrations in the post-consumer samples in comparison with virgin HDPE. However, the overall concentrations in post-consumer recycled samples were similar to or lower than concentration ranges in comparison with virgin HDPE. Contamination with other HDPE untypical compounds was rare and was in most cases related to non-milk bottles, which are <2.1% of the input material of the recycling process. The maximum concentration found in one sample of 1 g was estimated as 130 mg kg(-1), which corresponds to a contamination of 5200-6500 mg kg(-1) in the individual bottle. The recycling process investigated was based on an efficient sorting process, a hot-washing of the ground bottles, and a further deep-cleaning of the flakes with high temperatures and vacuum. Based on the fact that the contamination levels of post-consumer flake samples are similar to virgin HDPE and on the high cleaning efficiency of the super-clean recycling process especially for highly volatile compounds, the recycling process investigated is suitable for recycled post-consumer HDPE bottles for direct food-contact applications. However, hand-picking after automatically sorting is recommended to decrease the amount of non-milk bottles. The conclusions for suitability are valid, provided that the migration testing of recyclate contains milk bottles up to 100% and that both shelf-life testing and sensorial testing of the products are successful, which are topics of further investigations.

Contribution of water vapor pressure to pressurization of plutonium dioxide storage containers

NASA Astrophysics Data System (ADS)

Veirs, D. Kirk; Morris, John S.; Spearing, Dane R.

2000-07-01

Pressurization of long-term storage containers filled with materials meeting the US DOE storage standard is of concern.1,2 For example, temperatures within storage containers packaged according to the standard and contained in 9975 shipping packages that are stored in full view of the sun can reach internal temperatures of 250 °C.3 Twenty five grams of water (0.5 wt.%) at 250 °C in the storage container with no other material present would result in a pressure of 412 psia, which is limited by the amount of water. The pressure due to the water can be substantially reduced due to interactions with the stored material. Studies of the adsorption of water by PuO2 and surface interactions of water with PuO2 show that adsorption of 0.5 wt.% of water is feasible under many conditions and probable under high humidity conditions.4,5,6 However, no data are available on the vapor pressure of water over plutonium dioxide containing materials that have been exposed to water.

Variability in the composition of phenolic compounds in winter-dormant Salix pyrolifolia in relation to plant part and age.

PubMed

Lavola, Anu; Maukonen, Merja; Julkunen-Tiitto, Riitta

2018-06-12

The phenolic phytochemicals of winter-dormant Salix pyrolifolia were determined from the vegetative buds, and the bark and wood of different-aged twigs by HPLC-DAD and UHPLC-QTOF-MS analyses. All the plant parts were composed of salicylate glucosides and the other Salix-specific, simple phenolic glucosides as well as of phenolic acids, flavonoids and the high molecular-weight condensed tannins. The flavonoid composition was most diverse in buds and they also contained a large amount of chlorogenic acid (5-caffeoylquinic acid IUPAC), while salicylate glucosides and simple phenolic glucosides predominated in bark. The wooden interior part of the twigs contained fewer components and the lowest concentrations of compounds. Salicortin was the main compound in winter-dormant S. pyrolifolia (over 10% of bark biomass), but the concentrations of picein, salireposide, isosalipurposide, catechin and condensed tannins were also high. The flavonoid composition was highly naringenin- and quercetin-biassed. The composition of phytochemicals was organ-specific and remained relatively similar between different-aged trees. However, there were compound-specific fluctuations in the concentrations of phytochemicals with the age of the trees and within plant parts. Generally, the one-year-old plants differed from the older trees in their high concentration of condensed tannins in all the plant parts studied and in the highest concentration of isosalipurposide in bark, while the total amounts of salicylate glucosides in plant parts, and of naringenin glucosides in buds, tended to be highest in 20 year-old-trees. Copyright © 2018 Elsevier Ltd. All rights reserved.

APPROXIMATE ENZYMIC METHOD OF MICROANALYSIS FOR IDENTIFYING RESIDUAL AMOUNTS OF ORGANOPHOSPHORUS INSECTICIDES,

DTIC Science & Technology

plant extracts gradually increases. This is evidently explained by a conversion of the insecticide into a compound possessing high anticholinesterase activity . (Author)...possible to determine from 1 to 100 micrograms of insecticide per 1 ml. It was established that the anticholinesterase activity of chlorphos when...inherent anticholinesterase action, was developed. In order to realize this method a portable kit was constructed which contains a rack for the storage

Snacks for Toddlers

MedlinePlus

... them more likely to overeat. A word about juice. Juice — even 100% fruit juice — contains about the same amount of calories as soda. And juice drinks have excessive amounts of added sugar. Letting ...

Influence of dietary protein and excess methionine on choline needs for young bobwhite quail

USGS Publications Warehouse

Serafin, J.A.

1982-01-01

Experiments were conducted with young Bobwhite quail (Colinus virginianus) to investigate the effect of differing dietary protein levels and nondetrimental amounts of excess methionine on choline needs. Growth and feed consumption of quail fed an adequate (27.3%) protein purified diet supplemented with 2000 mg/kg of choline were unaffected by increasing the level of excess methionine to 1.75%; however, greater amounts (2.0%, 2.25%) of excess methionine depressed growth (P less than .01), reduced feed consumption (P less than .01), and decreased feed utilization (P less than .05). Quail fed a purified diet containing 13.85% protein and 515 mg/kg of choline grew poorly. Growth was unaffected by additional choline in this diet. Growth was suboptimal among quail fed purified diets containing adequate or high (41.55%) levels of protein in which choline was limiting; however, a high level of protein did not in itself affect performance. Growth was improved by supplemental choline in these diets. Growth of quail fed purified diets with up to 1.35% excess methionine which were limiting (531 mg/kg) in choline was less than that of groups fed 2000 mg/kg of added dietary choline (P less than .01); however, excess methionine did not significantly influence growth of quail fed choline-deficient diets. These experiments indicate that neither high dietary protein nor excess methionine, fed at non-growth-depressing levels, increases dietary choline needs for young Bobwhite quail.

High amount of dietary fiber not harmful but favorable for Crohn disease.

PubMed

Chiba, Mitsuro; Tsuji, Tsuyotoshi; Nakane, Kunio; Komatsu, Masafumi

2015-01-01

Current chronic diseases are a reflection of the westernized diet that features a decreased consumption of dietary fiber. Indigestible dietary fiber is metabolized by gut bacteria, including Faecalibacterium prausnitzii, to butyrate, which has a critical role in colonic homeostasis owing to a variety of functions. Dietary fiber intake has been significantly inversely associated with the risk of chronic diseases. Crohn disease (CD) is not an exception. However, even authors who reported the inverse association between dietary fiber and a risk of CD made no recommendation of dietary fiber intake to CD patients. Some correspondence was against advocating high fiber intake in CD. We initiated a semivegetarian diet (SVD), namely a lacto-ovo-vegetarian diet, for patients with inflammatory bowel disease. Our SVD contains 32.4 g of dietary fiber in 2000 kcal. There was no untoward effect of the SVD. The remission rate with combined infliximab and SVD for newly diagnosed CD patients was 100%. Maintenance of remission on SVD without scheduled maintenance therapy with biologic drugs was 92% at 2 years. These excellent short- and long-term results can be explained partly by SVD. The fecal bacterial count of F prausnitzii in patients with CD is significantly lower than in healthy controls. Diet reviews recommend plant-based diets to treat and to prevent a variety of chronic diseases. SVD belongs to plant-based diets that inevitably contain considerable amounts of dietary fiber. Our clinical experience and available data provide a rationale to recommend a high fiber intake to treat CD.

Noble Metal Arsenides and Gold Inclusions in Northwest Africa 8186

NASA Technical Reports Server (NTRS)

Srinivasan, P.; McCubbin, F. M.; Rahman, Z.; Keller, L. P.; Agee, C. B.

2016-01-01

CK carbonaceous chondrites are a highly thermally altered group of carbonaceous chondrites, experiencing temperatures ranging between approximately 576-867 degrees Centigrade. Additionally, the mineralogy of the CK chondrites record the highest overall oxygen fugacity of all chondrites, above the fayalite-magnetite-quartz (FMQ) buffer. Me-tallic Fe-Ni is extremely rare in CK chondrites, but magnetite and Fe,Ni sulfides are commonly observed. Noble metal-rich inclusions have previously been found in some magnetite and sulfide grains. These arsenides, tellurides, and sulfides, which contain varying amounts of Pt, Ru, Os, Te, As, Ir, and S, are thought to form either by condensation from a solar gas, or by exsolution during metamorphism on the chondritic parent body. Northwest Africa (NWA) 8186 is a highly metamorphosed CK chondrite. This meteorite is predominately composed of NiO-rich forsteritic olivine (Fo65), with lesser amounts of plagioclase (An52), augite (Fs11Wo49), magnetite (with exsolved titanomagnetite, hercynite, and titanohematite), monosulfide solid solution (with exsolved pentlandite), and the phosphate minerals Cl-apatite and merrillite. This meteorite contains coarse-grained, homogeneous silicates, and has 120-degree triple junctions between mineral phases, which indicates a high degree of thermal metamorphism. The presence of NiO-rich olivine, oxides phases all bearing Fe3 plus, and the absence of metal, are consistent with an oxygen fugacity above the FMQ buffer. We also observed noble metal-rich phases within sulfide grains in NWA 8186, which are the primary focus of the present study.

Noble Metal Arsenides and Gold Inclusions in Northwest Africa 8186

NASA Technical Reports Server (NTRS)

Srinivasan, P.; McCubbin, F. M.; Rahman, Z.; Keller, L. P.; Agee, C. B.

2016-01-01

CK carbonaceous chondrites are a highly thermally altered group of carbonaceous chondrites, experiencing temperatures ranging between approx.576-867 C. Additionally, the mineralogy of the CK chondrites record the highest overall oxygen fugacity of all chondrites, above the fayalite-magnetite-quartz (FMQ) buffer. Metallic Fe-Ni is extremely rare in CK chondrites, but magnetite and Fe,Ni sulfides are commonly observed. Noble metal-rich inclusions have previously been found in some magnetite and sulfide grains. These arsenides, tellurides, and sulfides, which contain varying amounts of Pt, Ru, Os, Te, As, Ir, and S, are thought to form either by condensation from a solar gas, or by exsolution during metamorphism on the chondritic parent body. Northwest Africa (NWA) 8186 is a highly metamorphosed CK chondrite. This meteorite is predominately composed of NiO-rich forsteritic olivine (Fo65), with lesser amounts of plagioclase (An52), augite (Fs11Wo49), magnetite (with exsolved titanomagnetite, hercynite, and titanohematite), monosulfide solid solution (with exsolved pentlandite), and the phosphate minerals Cl-apatite and merrillite. This meteorite contains coarse-grained, homogeneous silicates, and has 120deg triple junctions between mineral phases, which indicates a high degree of thermal metamorphism. The presence of NiO-rich olivine, oxides phases all bearing Fe3+, and the absence of metal, are consistent with an oxygen fugacity above the FMQ buffer. We also observed noble metal-rich phases within sulfide grains in NWA 8186, which are the primary focus of the present study.

Effect of Mn and Fe on the Formation of Fe- and Mn-Rich Intermetallics in Al-5Mg-Mn Alloys Solidified Under Near-Rapid Cooling.

PubMed

Liu, Yulin; Huang, Gaoren; Sun, Yimeng; Zhang, Li; Huang, Zhenwei; Wang, Jijie; Liu, Chunzhong

2016-01-29

Mn was an important alloying element used in Al-Mg-Mn alloys. However, it had to be limited to a low level (<1.0 wt %) to avoid the formation of coarse intermetallics. In order to take full advantage of the benefits of Mn, research was carried out to investigate the possibility of increasing the content of Mn by studying the effect of cooling rate on the formation of Fe- and Mn-rich intermetallics at different content levels of Mn and Fe. The results indicated that in Al-5Mg-Mn alloy with low Fe content (<0.1 wt %), intermetallic Al₆(Fe,Mn) was small in size and amount. With increasing Mn content, intermetallic Al₆(Fe,Mn) increased, but in limited amount. In high-Fe-containing Al-5Mg-Mn alloys (0.5 wt % Fe), intermetallic Al₆(Fe,Mn) became the dominant phase, even in the alloy with low Mn content (0.39 wt %). Cooling rate played a critical role in the refinement of the intermetallics. Under near-rapid cooling, intermetallic Al₆(Fe,Mn) was extremely refined. Even in the high Mn and/or high-Fe-containing alloys, it still demonstrated fine Chinese script structures. However, once the alloy composition passed beyond the eutectic point, the primary intermetallic Al₆(Fe,Mn) phase displayed extremely coarse platelet-like morphology. Increasing the content of Fe caused intermetallic Al₆(Fe,Mn) to become the primary phase at a lower Mn content.

A novel benzimidazole-functionalized 2-D COF material: synthesis and application as a selective solid-phase extractant for separation of uranium.

PubMed

Li, Juan; Yang, Xiaodan; Bai, Chiyao; Tian, Yin; Li, Bo; Zhang, Shuang; Yang, Xiaoyu; Ding, Songdong; Xia, Chuanqin; Tan, Xinyu; Ma, Lijian; Li, Shoujian

2015-01-01

A novel COF-based material (COF-COOH) containing large amounts of carboxylic groups was prepared for the first time by using a simple and effective one-step synthetic method, in which the cheap and commercially available raw materials, trimesoyl chloride and p-phenylenediamine, were used. The as-synthesized COF-COOH was modified with previously synthesized 2-(2,4-dihydroxyphenyl)-benzimidazole (HBI) by "grafting to" method, and a new solid-phase extractant (COF-HBI) with highly efficient sorption performance for uranium(VI) was consequently obtained. A series of characterizations demonstrated that COF-COOH and COF-HBI exhibited great thermostabilities and irradiation stabilities. Sorption behavior of the COF-based materials toward U(VI) was compared in simulated nuclear industrial effluent containing UO2(2+) and 11 undesired ions, and the UO2(2+) sorption amount of COF-HBI was 81 mg g(-1), accounting for approximately 58% of the total sorption amount, which was much higher than the sorption selectivity of COF-COOH to UO2(2+) (39%). Batch sorption experiment results indicated that the uranium(VI) sorption on COF-HBI was a pH dependent, rapid (sorption equilibrium was reached in 30 min), endothermic and spontaneous process. In the most favorable conditions, the equilibrium sorption capacity of the adsorbent for uranium could reach 211 mg g(-1). Copyright © 2014 Elsevier Inc. All rights reserved.

[The peroxidase content of human tears].

PubMed

Buchberger, W; Rieger, G

1989-01-01

The peroxidase-(POD)-thiocyanate-hydrogenperoxide-system is a well-known antibacterial system, which has been demonstrated to exist, for example, in milk and saliva. Earlier investigations by van Haeringen et al. established a POD level in human tears of 10(3) units/l, yet the thiocyanate concentration was only about 0.2 mmol/l. Therefore van Haeringen et al. excluded the existence of a POD-thiocyanate-hydrogenperoxide antibacterial system in human tears because of the insufficient amount of thiocyanate in the tears examined. Instead of thiocyanate halides such as J- can also complete the POD hydrogen peroxide system as electron donors. Sufficient amounts of iodide can be expected after the application of iodine-containing eye drops or after local treatment with iodine-containing brine, as done in Bad Hall in Austria. Therefore, the above mentioned antibacterial system may be of importance if the POD-level is high enough (greater than 250 units/l). We investigated 22 tear samples from healthy persons: the POD levels were below 20 units/l in 19 cases; in 3 cases the POD concentration was found to be between 20 and 50 units/l. Therefore, in normal human tear fluid, not only the amount of thiocyanate but also the concentration of POD is too low for effective antimicrobial activity of the peroxidase-thiocyanate-hydrogenperoxide system. It is so far not known whether this system is effective under pathological conditions.

Lyophilised wafers as vehicles for the topical release of chlorhexidine digluconate--release kinetics and efficacy against Pseudomonas aeruginosa.

PubMed

Labovitiadi, Olga; Lamb, Andrew J; Matthews, Kerr H

2012-12-15

There is a requirement to deliver accurate amounts of broad spectrum antimicrobial compounds locally to exuding wounds. Varying amounts of exudate complicates this process by limiting the residence and therefore efficacy of active substances. Minimum bactericidal concentrations (MBC) of antimicrobials are necessary to suppress infection and lessen the chances of resistant strains of potentially pathogenic bacteria from prevailing. Polysaccharide wafers can adhere to exudating wound beds, absorbing fluids and forming highly viscous gels that remain in situ for prolonged periods of time to release sustained amounts of antimicrobial. In this study, five different formulations were produced containing the antimicrobial, chlorhexidine digluconate (CHD). Absorption of simulated wound fluid, resultant rheological properties of gels and efficacy against plated cultures of Pseudomonas aeruginosa were measured and compared. CHD reduced the 'water uptake' of wafers by 11-50% (w/w) and decreased the rheological consistency of non-SA containing gels by 10-65%. Release studies indicated that karaya wafers gave the highest sustained release of CHD, >60 μg/mL in 24 h, well in excess of the MBC for P. aeruginosa. Release kinetics indicated an anomalous diffusion mechanism according to Korsmeyer-Peppas, with diffusion exponents varying from 0.31 to 0.41 for most wafers except xanthan (0.65). Copyright © 2012 Elsevier B.V. All rights reserved.

Comparative Toxicity of Selected Aviation Fuels as Measured by Insect Bioassay

DTIC Science & Technology

1982-07-01

structure in termites , ants, and bees can be used to contrast the toxicity of a compound. A comparative study of toxicity can also be made using a...and also serve as sex pheromones , kairomones, and defensive compounds. Cuticular hydrocarbons vary significantly in structure and amount by species...in flour beetles. Flour beetles contain hydrocarbons which function as sex pheromones and also contain a significant amount of 1-pentadecene which

Elemental speciation for chromium in chromium picolinate products

NASA Astrophysics Data System (ADS)

Ding, Hong; Olson, Lisa K.; Caruso, Joseph A.

1996-12-01

Chromium picolinate products have been examined for different forms of chromium, using chromatographic separation and inductively coupled plasma mass spectrometric detection. The brands we evaluated contained no detectable amount of elemental chromium(VI), the toxic form. Since chromium picolinate might have other chromium forms as impurities, different products may contain different forms of chromium species. Compared with ion-exchange, reversed-phase chromatography showed excellent chromium recovery based on the amount stated on the product label.

The National Shipbuilding Research Program. Shipyard Welding Emission Factor Development

DTIC Science & Technology

1999-09-01

percent composition in the rod/wire. Three specific HAPs of concern were identified: 1. Chrome and chromium compounds; 2. Nickel and nickel compounds...welding processes. These are: 1. Those rod/wires reported to be used in the largest amounts (> 10,000 pounds annually) did not contain chromium or...amounts ranging from less than 1,000 to greater than 10,000 pounds annually contained chromium and chromium compounds in concentrations ranging from

Chlorophyll a/b-binding proteins, pigment conversions, and early light-induced proteins in a chlorophyll b-less barley mutant.

PubMed Central

Król, M; Spangfort, M D; Huner, N P; Oquist, G; Gustafsson, P; Jansson, S

1995-01-01

Monospecific polyclonal antibodies have been raised against synthetic peptides derived from the primary sequences from different plant light-harvesting Chl a/b-binding (LHC) proteins. Together with other monospecific antibodies, these were used to quantify the levels of the 10 different LHC proteins in wild-type and chlorina f2 barley (Hordeum vulgare L.), grown under normal and intermittent light (ImL). Chlorina f2, grown under normal light, lacked Lhcb1 (type I LHC II) and Lhcb6 (CP24) and had reduced amounts of Lhcb2, Lhcb3 (types II and III LHC II), and Lhcb4 (CP 29). Chlorina f2 grown under ImL lacked all LHC proteins, whereas wild-type ImL plants contained Lhcb5 (CP 26) and a small amount of Lhcb2. The chlorina f2 ImL thylakoids were organized in large parallel arrays, but wild-type ImL thylakoids had appressed regions, indicating a possible role for Lhcb5 in grana stacking. Chlorina f2 grown under ImL contained considerable amounts of violaxanthin (2-3/reaction center), representing a pool of phototransformable xanthophyll cycle pigments not associated with LHC proteins. Chlorina f2 and the plants grown under ImL also contained early light-induced proteins (ELIPs) as monitored by western blotting. The levels of both ELIPs and xanthophyll cycle pigments increased during a 1 h of high light treatment, without accumulation of LHC proteins. These data are consistent with the hypothesis that ELIPs are pigment-binding proteins, and we suggest that ELIPs bind photoconvertible xanthophylls and replace "normal" LHC proteins under conditions of light stress. PMID:7748263

Gypsum treated fly ash as a liner for waste disposal facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivapullaiah, Puvvadi V., E-mail: siva@civil.iisc.ernet.in; Baig, M. Arif Ali, E-mail: reach2arif@gmail.com

2011-02-15

Fly ash has potential application in the construction of base liners for waste containment facilities. While most of the fly ashes improve in the strength with curing, the ranges of permeabilities they attain may often not meet the basic requirement of a liner material. An attempt has been made in the present context to reduce the hydraulic conductivity by adding lime content up to 10% to two selected samples of class F fly ashes. The use of gypsum, which is known to accelerate the unconfined compressive strength by increasing the lime reactivity, has been investigated in further improving the hydraulicmore » conductivity. Hydraulic conductivities of the compacted specimens have been determined in the laboratory using the falling head method. It has been observed that the addition of gypsum reduces the hydraulic conductivity of the lime treated fly ashes. The reduction in the hydraulic conductivity of the samples containing gypsum is significantly more for samples with high amounts of lime contents (as high as 1000 times) than those fly ashes with lower amounts of lime. However there is a relatively more increase in the strengths of the samples with the inclusion of gypsum to the fly ashes at lower lime contents. This is due to the fact that excess lime added to fly ash is not effectively converted into pozzolanic compounds. Even the presence of gypsum is observed not to activate these reactions with excess lime. On the other hand the higher amount of lime in the presence of sulphate is observed to produce more cementitious compounds which block the pores in the fly ash. The consequent reduction in the hydraulic conductivity of fly ash would be beneficial in reducing the leachability of trace elements present in the fly ash when used as a base liner.« less

Corrosion tests in Hawaiian geothermal fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larsen-Basse, J.; Lam, Kam-Fai

1984-01-01

Exposure tests were conductd in binary geothermal brine on the island of Hawaii. The steam which flashes from the high pressure, high temperature water as it is brought to ambient pressure contains substantial amounts of H{sub 2}S. In the absence of oxygen this steam is only moderately aggressive but in the aerated state it is highly aggressive to carbon steels and copper alloys. The liquid after flasing is intermediately aggressive. The Hawaiian fluid is unique in chemistry and corrosion behavior; its corrosiveness is relatively mild for a geothermal fluid falling close to the Iceland-type resources. 24 refs., 7 figs., 5more » tabs.« less

Platelets from patients with the Quebec platelet disorder contain and secrete abnormal amounts of urokinase-type plasminogen activator.

PubMed

Kahr, W H; Zheng, S; Sheth, P M; Pai, M; Cowie, A; Bouchard, M; Podor, T J; Rivard, G E; Hayward, C P

2001-07-15

The Quebec platelet disorder (QPD) is an autosomal dominant platelet disorder associated with delayed bleeding and alpha-granule protein degradation. The degradation of alpha-granule, but not plasma, fibrinogen in patients with the QPD led to the investigation of their platelets for a protease defect. Unlike normal platelets, QPD platelets contained large amounts of fibrinolytic serine proteases that had properties of plasminogen activators. Western blot analysis, zymography, and immunodepletion experiments indicated this was because QPD platelets contained large amounts of urokinase-type plasminogen activator (u-PA) within a secretory compartment. u-PA antigen was not increased in all QPD plasmas, whereas it was increased more than 100-fold in QPD platelets (P <.00009), which contained increased u-PA messenger RNA. Although QPD platelets contained 2-fold more plasminogen activator inhibitor 1 (PAI-1) (P <.0008) and 100-fold greater u-PA-PAI-1 complexes (P <.0002) than normal platelets, they contained excess u-PA activity, predominantly in the form of two chain (tcu-PA), which required additional PAI-1 for full inhibition. There was associated proteolysis of plasminogen in QPD platelets, to forms that comigrated with plasmin. When similar amounts of tcu-PA were incubated with normal platelet secretory proteins, many alpha-granule proteins were proteolyzed to forms that resembled degraded QPD platelet proteins. These data implicate u-PA in the pathogenesis of alpha-granule protein degradation in the QPD. Although patients with the QPD have normal to increased u-PA levels in their plasma, without evidence of systemic fibrinogenolysis, their increased platelet u-PA could contribute to bleeding by accelerating fibrinolysis within the hemostatic plug. QPD is the only inherited bleeding disorder in humans known to be associated with increased u-PA.

Preparation and magnetic properties of phthalocyanine-based carbon materials containing transition metals

NASA Astrophysics Data System (ADS)

Honda, Z.; Sato, S.; Hagiwara, M.; Kida, T.; Sakai, M.; Fukuda, T.; Kamata, N.

2016-07-01

A simple method for the preparation of bulk quantities of magnetic carbon materials, which contain uniformly dispersed transition metals (M = Fe, Co, Ni, and Cu) as the magnetic components, is presented. By using highly chlorinated metal phthalocyanine as the building block and potassium as the coupling reagent, phthalocyanine-based carbon materials (PBCMs) containing transition metals were obtained. Our experiments demonstrate the structure of these PBCMs consists of transition metals embedded in graphitic carbon that includes a square planar MN4 magnetic core and the Fe and Co-PBCM possess spontaneous magnetization at room temperature. In addition, carbon-coated transition metal particles were obtained by the Wurtz-type reaction with excess amount of potassium coupling agent. The large transition metal surface area and magnetization of these M-PBCMs are useful for spintronic and catalytic applications.

Thermally induced degradation of sulfur-containing aliphatic glucosinolates in broccoli sprouts (Brassica oleracea var. italica) and model systems.

PubMed

Hanschen, Franziska S; Platz, Stefanie; Mewis, Inga; Schreiner, Monika; Rohn, Sascha; Kroh, Lothar W

2012-03-07

Processing reduces the glucosinolate (GSL) content of plant food, among other aspects due to thermally induced degradation. Since there is little information about the thermal stability of GSL and formation of corresponding breakdown products, the thermally induced degradation of sulfur-containing aliphatic GSL was studied in broccoli sprouts and with isolated GSL in dry medium at different temperatures as well as in aqueous medium at different pH values. Desulfo-GSL have been analyzed with HPLC-DAD, while breakdown products were estimated using GC-FID. Whereas in the broccoli sprouts structural differences of the GSL with regard to thermal stability exist, the various isolated sulfur-containing aliphatic GSL degraded nearly equally and were in general more stable. In broccoli sprouts, methylsulfanylalkyl GSL were more susceptible to degradation at high temperatures, whereas methylsulfinylalkyl GSL were revealed to be more affected in aqueous medium under alkaline conditions. Besides small amounts of isothiocyanates, the main thermally induced breakdown products of sulfur-containing aliphatic GSL were nitriles. Although they were most rapidly formed at comparatively high temperatures under dry heat conditions, their highest concentrations were found after cooking in acidic medium, conditions being typical for domestic processing.

Design of an experiment for the production of a foamed tin sample

NASA Technical Reports Server (NTRS)

Wernimont, E.

1986-01-01

One of the major experiments in the GAS container is concerned with the experimental production of a foamed metal. A foamed metal is one that contains a significant amount of gas bubbles suspended in its solid volume. Purdue's GAS team proposes to do this with the help of a solid zinc carbonate that gives off carbon dioxide at high temperatures. Because of low energy requirements, the metal used for this experiment is tin. It is hoped that the use of near zero environment will keep the suspended bubbles more uniform than in an Earth based process, hence not depleting the physical strength of the material as greatly as is observed on Earth.

Overproduction and nucleotide sequence of the respiratory D-lactate dehydrogenase of Escherichia coli.

PubMed Central

Rule, G S; Pratt, E A; Chin, C C; Wold, F; Ho, C

1985-01-01

Recombinant DNA plasmids containing the gene for the membrane-bound D-lactate dehydrogenase (D-LDH) of Escherichia coli linked to the promoter PL from lambda were constructed. After induction, the levels of D-LDH were elevated 300-fold over that of the wild type and amounted to 35% of the total cellular protein. The nucleotide sequence of the D-LDH gene was determined and shown to agree with the amino acid composition and the amino-terminal sequence of the purified enzyme. Removal of the amino-terminal formyl-Met from D-LDH was not inhibited in cells which contained these high levels of D-LDH. Images PMID:3882663

Properties of probiotics and encapsulated probiotics in food.

PubMed

Ozyurt, V Hazal; Ötles, Semih

2014-01-01

Probiotics are microorganisms which confer health benefits upon application in sufficiently-high viable cell amounts. Probiotics are typically members of Lactobacillus and Bifidobacterium species commonly associated with human gastrointestinal tracts. In the recent past, there has been a rising interest in producing functional foods containing encapsulated probiotic bacteria. Recent studies have been reported using dairy products like cheese, yogurt and ice cream as food carrier, and non-dairy products like meat, fruits, cereals, chocolate, etc. However, the industrial sector contains only few encapsulated probiotic products. Probiotics have been developed by several companies in a capsule or a tablet form. The review compiles probiotics, encapsulation technology and cell life in the food matrices.

Triaxial X-Ray Diffraction Method and its Application to Monitor Residual Stress in Surface Layers after High-Feed Milling

NASA Astrophysics Data System (ADS)

Zaušková, Lucia; Czán, Andrej; Šajgalík, Michal; Pobijak, Jozef; Mikloš, Matej

2017-10-01

High-feed milling is a milling method characteristic with shallow depth of cut and high feed rate to maximize the amount of removed metal from a part, generating residual stresses in the surface and subsurface layers of the machined parts. The residual stress has a large influence on the functional properties of the components. The article is focused on the application of triaxial x-ray diffraction method to monitor residual stresses after high feed milling. Significance of triaxial measuring method is the capability of measuring in different angles so it is possible to acquire stress tensor containing normal and shear stress components.

Measurement and reduction of micro-bubble formation in high-viscosity fluids

NASA Astrophysics Data System (ADS)

Tom, Glenn; Liu, Wei

2012-03-01

Gases at high drive pressure can initially dissolve into the fluids used in lithography and other critical processes during the fabrication of integrated circuits. In the low pressure portion of the dispense train, the dissolved gases can revert to bubbles. These bubbles can: 1. Affect the compressibility of the working fluid and change the flow characteristics of the dispense heads which require frequent re-tuning of the coating tools. 2. Contribute to defect formation if the bubbles are trapped on the surface of the wafer. Photosensitive Polyimides (PI) have high viscosities (1000 to 20,000 cP). Because of the high viscosity, high-powered, expensive pumps are needed to effectively remove the fluid from its container. Suction from the pump filling cycle easily causes cavitation, which can create flow rate variability, and micro-bubble formation. It is a common practice to apply pressure to the PI resists to minimize cavitation in the pump. The trade-off to this practice is the entrainment (dissolution) of the drive gas into the resist and the risk of micro-bubbles forming later in the dispense train. In the current study, ATMI measured the effects of two methods of pressure dispense from the container on the amount of gas entrained in a viscous fluid: (1) indirect pressure dispense and (2) direct pressure dispense. The main analytical method employed to measure the amount of dissolved gases is a gas chromatograph (GC), which can measure the concentration of gases dissolved in a volatile fluid. It is not suitable to measure gases in low volatility fluids. The new test method developed, however, is capable of measuring dissolved gases in low volatility fluids.

Effects of Lycopene on the Initial State of Atherosclerosis in New Zealand White (NZW) Rabbits

PubMed Central

Lorenz, Mario; Fechner, Mandy; Kalkowski, Janine; Fröhlich, Kati; Trautmann, Anne; Böhm, Volker; Liebisch, Gerhard; Lehneis, Stefan; Schmitz, Gerd; Ludwig, Antje; Baumann, Gert; Stangl, Karl; Stangl, Verena

2012-01-01

Background Lycopene is the main carotenoid in tomatoes, where it is found in high concentrations. Strong epidemiological evidence suggests that lycopene may provide protection against cardiovascular diseases. We therefore studied the effects of lycopene on diet-induced increase in serum lipid levels and the initiation of atherosclerosis in New Zealand White (NZW) rabbits. Methodology/Principal Findings The animals, divided into four groups of 9 animals each, were fed either a standard diet, a high-cholesterol diet containing 0.5% cholesterol, a high-cholesterol diet containing placebo beadlets, or a high-cholesterol diet plus 5 mg/kg body weight/day of lycopene (in the form of lycopene beadlets), for a period of 4 weeks. We found significantly elevated lycopene plasma levels in the animal group treated with lycopene beadlets. Compared to the high-cholesterol and the placebo group, this was associated with a significant reduction of 50% in total cholesterol and LDL cholesterol serum levels in the lycopene group. The amount of cholesteryl ester in the aorta was significantly decreased by lycopene. However, we did not observe a significant decrease in the extent of aortic surface lipid accumulation in the lycopene group. In addition, no differences in the intima-media thickness among groups were observed. Endothelial-dependent and endothelial-independent vasodilation in isolated rabbit aortic and carotid rings did not differ among any of the animal groups. Conclusions Lycopene supplementation for 4 weeks increased lycopene plasma levels in the animals. Although we found strongly reduced total and LDL cholesterol serum levels as well as significantly lower amounts of cholesteryl ester in the aortae in the lycopene-treated group, no significant differences in initial lesions in the aortae were detected. PMID:22295112

42 CFR 405.740 - Principles for determining the amount in controversy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Principles for determining the amount in... Reconsiderations and Appeals Under Medicare Part A § 405.740 Principles for determining the amount in controversy... more appellants, the Secretary may assert that the aggregation principles contained in this subpart may...

26 CFR 1.263(a)-4 - Amounts paid to acquire or create intangibles.

Code of Federal Regulations, 2010 CFR

2010-04-01

...). (v) Creation of package design. Amounts paid to develop a package design are treated as amounts that...). For purposes of this section, the term package design means the specific graphic arrangement or design... design of a container with respect to its shape or function. (4) Coordination with other provisions of...

Effects of Varying Proportions of Glass on Reflectance Spectra of HED Polymict Breccias

NASA Technical Reports Server (NTRS)

Buchanan, P. C.; Reddy, V; LeCorre, L.; Cloutis, E. A.; Mann, P.; Le, L.

2014-01-01

Some meteorites contain significant amounts of glass, which, in most cases, probably results from impact processes on parent bodies.. Yamato 82202 is an example of one of the unequilibrated eucrites that contains significant proportions of impact glass distributed as veins throughout the meteorite. In other cases, fragments of glass are distributed throughout polymict breccias. For example, the polymict eucrite EET 87509 contains rare angular fragments of devitrified glass. Proportions of glass in most of these meteorites and in lithic clasts within these meteorites may vary locally from small amounts (less than one percent) to much larger amounts (subequal proportions of glass and mineral material). For example, some fragments within the South African polymict eucrite Macibini contain approximately 50% glass. The presence of these variable proportions of meteorite glass confirm the increased recognition that impact processes played an important role in the histories of asteroidal bodies. This study attempts to quantify the effects of a glass component on reflectance spectra by analyzing in the laboratory mixtures of varying proportions of a well-characterized HED polymict breccia and glass derived by melting a bulk sample of that breccia.

The dopant type and amount governs the electrochemical performance of graphene platforms for the antioxidant activity quantification

NASA Astrophysics Data System (ADS)

Hui, Kai Hwee; Ambrosi, Adriano; Sofer, Zdeněk; Pumera, Martin; Bonanni, Alessandra

2015-05-01

Graphene doped with heteroatoms can show new or improved properties as compared to the original undoped material. It has been reported that the type of heteroatoms and the doping conditions can have a strong influence on the electronic and electrochemical properties of the resulting material. Here, we wish to compare the electrochemical behavior of two n-type and two p-type doped graphenes, namely boron-doped graphenes and nitrogen-doped graphenes containing different amounts of heteroatoms. We show that the boron-doped graphene containing a higher amount of dopants provides the best electroanalytical performance in terms of calibration sensitivity, selectivity and linearity of response for the detection of gallic acid normally used as the standard probe for the quantification of antioxidant activity of food and beverages. Our findings demonstrate that the type and amount of heteroatoms used for the doping have a profound influence on the electrochemical detection of gallic acid rather than the structural properties of the materials such as amounts of defects, oxygen functionalities and surface area. This finding has a profound influence on the application of doped graphenes in the field of analytical chemistry.Graphene doped with heteroatoms can show new or improved properties as compared to the original undoped material. It has been reported that the type of heteroatoms and the doping conditions can have a strong influence on the electronic and electrochemical properties of the resulting material. Here, we wish to compare the electrochemical behavior of two n-type and two p-type doped graphenes, namely boron-doped graphenes and nitrogen-doped graphenes containing different amounts of heteroatoms. We show that the boron-doped graphene containing a higher amount of dopants provides the best electroanalytical performance in terms of calibration sensitivity, selectivity and linearity of response for the detection of gallic acid normally used as the standard probe for the quantification of antioxidant activity of food and beverages. Our findings demonstrate that the type and amount of heteroatoms used for the doping have a profound influence on the electrochemical detection of gallic acid rather than the structural properties of the materials such as amounts of defects, oxygen functionalities and surface area. This finding has a profound influence on the application of doped graphenes in the field of analytical chemistry. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr01045d

Naphthenic acids removal from high TDS produced water by persulfate mediated iron oxide functionalized catalytic membrane, and by nanofiltration.

PubMed

Aher, Ashish; Papp, Joseph; Colburn, Andrew; Wan, Hongyi; Hatakeyama, Evan; Prakash, Prakhar; Weaver, Ben; Bhattacharyya, Dibakar

2017-11-01

Oil industries generate large amounts of produced water containing organic contaminants, such as naphthenic acids (NA) and very high concentrations of inorganic salts. Recovery of potable water from produced water can be highly energy intensive is some cases due to its high salt concentration, and safe discharge is more suitable. Here, we explored catalytic properties of iron oxide (Fe x O y nanoparticles) functionalized membranes in oxidizing NA from water containing high concentrations of total dissolved solids (TDS) using persulfate as an oxidizing agent. Catalytic decomposition of persulfate by Fe x O y functionalized membranes followed pseudo-first order kinetics with an apparent activation energy of 18 Kcal/mol. Fe x O y functionalized membranes were capable of lowering the NA concentrations to less than discharge limits of 10 ppm at 40 °C. Oxidation state of iron during reaction was quantified. Membrane performance was investigated for extended period of time. A coupled process of advanced oxidation catalyzed by membrane and nanofiltration was also evaluated. Commercially available nanofiltration membranes were found capable of retaining NA from water containing high concentrations of dissolved salts. Commercial NF membranes, Dow NF270 (Dow), and NF8 (Nanostone) had NA rejection of 79% and 82%, respectively. Retentate for the nanofiltration was further treated with advanced oxidation catalyzed by Fe x O y functionalized membrane for removal of NA.

Tissue distribution of (/sup 14/C)methyl mercury in the lobster, Homarus americanus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guarino, A.M.; Anderson, J.B.; Pritchard, J.B.

1976-09-01

(/sup 14/C) Methyl mercury was administered to lobsters by three different routes: intravascular (iv) injection, ingestion, and absorption from the ambient water. After iv administration (0.1 mg/kg) (/sup 14/C) methyl mercury was rapidly removed from the plasma, followed by slow loss from the hepatopancreas and a strikingly persistent increase in the amount of radioactivity in the tail muscle. Most (80 to 90 percent) of the radioactivity in the hepatopancreas was shown by TLC methods to be the parent compound, and approximately 10 percent of this persisted for 6 days after injection. The half-life in this organ was found to bemore » 21 days. One month after iv treatment with methyl mercury, the only organs that contained more than 0.1 ppM of this xenobiotic were egg masses, male gonads, heart, brain, intestine, and tail muscle. The half-lives for disappearance from sexual organs were greater than 1 month. After ingestion of (/sup 14/C) methyl mercury (0.1 mg/kg) in food the hepatopancreas contained most of the administered dose at 6 days (68 percent), while the stomach (10 percent), tail muscle (8 percent), and carcass (15 percent) contained less. A unique distribution pattern emerged 6 days after exposure to (/sup 14/C) methyl mercury-containing ambient water (0.1 ppM). The tail muscle contained most (50 percent) of the absorbed dose, whereas the hepatopancreas and carcass containing only 23 and 10 percent, respectively. In view of the small molecular size and high liqid solubility of methyl mercury and the lipophilic properties of the chitin-protein exoskeleton of the lobster, it is likely that significant uptake directly from the water as well as storage of absorbed methyl mercury occurred in the tail region. Residue analysis on untreated lobsters indicated that the egg masses contained the largest amount of methyl mercury (0.1 ppM). The hepatopancreas and carcass (muscle) levels were less than 0.05 ppM.« less

Simultaneous effects of tocopheryl polyethylene glycol succinate (TPGS) on local hair growth promotion and systemic absorption of topically applied minoxidil in a mouse model.

PubMed

Chen, Chien-Ho; Sheu, Ming-Thau; Wu, An-Bang; Lin, Keng-Ping; Ho, Hsiu-O

2005-12-08

In this study, topical minoxidil solutions supplemented with TPGS in cosolvent systems of various compositions consisting of water, alcohol, and polyethylene glycol 400 were designed to evaluate the efficacy of promoting hair growth after topical application and the safety in terms of the amount of minoxidil absorbed through the skin into the circulation using C57BL/6J mice as a model. The commercial product of 2% Regaine) was used as the positive control. The role, which sulfotransferase activity plays in hair growth with treatment using minoxidil, was determined as well. The results revealed that the addition of 0.5% TPGS was able to enhance the proliferation of hair, but an increase in the amount of TPGS to 2% led to deterioration in the enhancement of hair growth. At the higher added amount (2.0%) of TPGS, the promotion of hair growth was slightly reduced for both cosolvent formulations F1 (100% water) and F3 (100% PEG 400), whereas it was reduced to a greater extent for the cosolvent formulations F8-F10. In comparison, the influences of cosolvent compositions with TPGS amounts of 0.0 and 2.0% on the promotion of hair growth were similar. On the contrary, variability in the promotion of hair growth by different solvent formulations was minimal when the added amount of TPGS was 0.5%. In general, a relationship between hair growth and sulfotransferase activities after topical application of 2% Regaine and minoxidil formulations containing various amounts of TPGS was not demonstrated. Plasma concentrations of minoxidil with 2% Regaine were found to be greater than those of 2% minoxidil in those cosolvent formulations containing various amounts of TPGS, while showing insignificant differences among those 10 cosolvent formulations with a fixed amount of TPGS. A tendency for the plasma concentration of minoxidil to increase after the topical administration of minoxidil formulations containing the higher amount of TPGS (2%) was noted.

Method of enhancing the electronic properties of an undoped and/or N-type hydrogenated amorphous silicon film

DOEpatents

Carlson, David E.

1980-01-01

The dark conductivity and photoconductivity of an N-type and/or undoped hydrogenated amorphous silicon layer fabricated by an AC or DC proximity glow discharge in silane can be increased through the incorporation of argon in an amount from 10 to about 90 percent by volume of the glow discharge atmosphere which contains a silicon-hydrogen containing compound in an amount of from about 90 to about 10 volume percent.

[Physical properties of resins for veneer crown. (Part 1) Bending strength of thermosetting methacrylic resins (author's transl)].

PubMed

Kashiwada, T

1979-01-01

The physical properties of thermosetting methacrylic resins contain a kind or more than two kinds of cross linking agents were investigated. Knoop hardness and bending strength after drying, water sorption and thermal cycling were listed in table 4 and 5. Hydrophilic resins absorbed water about 3 times as much as hydrophobic resins. The materials contain a small amount of hydrophobic cross linking agents in MMA indicate comparatively excellent properties after drying, water sorption and thermal cycling. Knoop hardness of resins generally reduced by water sorption, especially in the case of the resin contains a large amount of triethylene glycol dimethacrylate.

Determination of Total Soy Isoflavones in Dietary Supplements, Supplement Ingredients, and Soy Foods by High-Performance Liquid Chromatography with Ultraviolet Detection: Collaborative Study

PubMed Central

Collison, Mark W.

2008-01-01

An interlaboratory study was conducted to evaluate a method for determining total soy isoflavones in dietary supplements, dietary supplement ingredients, and soy foods. Isoflavones were extracted using aqueous acetonitrile containing a small amount of dimethylsulfoxide (DMSO) and all 12 of the naturally occuring isoflavones in soy were determined by high-performance liquid Chromatography (HPLC) with UV detection using apigenin as an internal standard. Fifteen samples (6 pairs of blind duplicates plus 3 additional samples) of soy isoflavone ingredients, soy isoflavone dietary supplements, soy flour, and soy protein products were successfully analyzed by 13 collaborating laboratories in 6 countries. For repeatability, the relative standard deviations (RSDr) ranged from 1.07 for samples containing over 400 mg/g total isoflavones to 3.31 for samples containing 0.87 mg/g total isoflavones, and for reproducibility the RSDR values ranged from 2.29 for samples containing over 400 mg/g total isoflavones to 9.36 for samples containing 0.87 mg/g total isoflavones. HorRat values ranged from 1.00 to 1.62 for all samples containing at least 0.8 mg/g total isoflavones. One sample, containing very low total isoflavones (<0.05 mg/g), gave RSDR values of 175 and a HorRat value of 17.6. This sample was deemed to be below the usable range of the method. The method provides accurate and precise results for analysis of soy isoflavones in dietary supplements and soy foods. PMID:18567292

Determination of total soy isoflavones in dietary supplements, supplement ingredients, and soy foods by high-performance liquid chromatography with ultraviolet detection: collaborative study.

PubMed

Collison, Mark W

2008-01-01

An interlaboratory study was conducted to evaluate a method for determining total soy isoflavones in dietary supplements, dietary supplement ingredients, and soy foods. Isoflavones were extracted using aqueous acetonitrile containing a small amount of dimethylsulfoxide (DMSO) and all 12 of the naturally occuring isoflavones in soy were determined by high-performance liquid chromatography (HPLC) with UV detection using apigenin as an internal standard. Fifteen samples (6 pairs of blind duplicates plus 3 additional samples) of soy isoflavone ingredients, soy isoflavone dietary supplements, soy flour, and soy protein products were successfully analyzed by 13 collaborating laboratories in 6 countries. For repeatability, the relative standard deviations (RSDr) ranged from 1.07 for samples containing over 400 mglg total isoflavones to 3.31 for samples containing 0.87 mg/g total isoflavones, and for reproducibility the RSDR values ranged from 2.29 for samples containing over 400 mg/g total isoflavones to 9.36 for samples containing 0.87 mg/g total isoflavones. HorRat values ranged from 1.00 to 1.62 for all samples containing at least 0.8 mg/g total isoflavones. One sample, containing very low total isoflavones (< 0.05 mg/g), gave RSDR values of 175 and a HorRat value of 17.6. This sample was deemed to be below the usable range of the method. The method provides accurate and precise results for analysis of soy isoflavones in dietary supplements and soy foods.

Kinetic Modeling of the Release of Ethylene Oxide from Sterilized Plastic Containers and its Interaction with Monoclonal Antibodies.

PubMed

Yu, Bryan Lei; Han, Jun; Hammond, Matthew; Wang, Xuemei; Zhang, Qingchun; Clausen, Andrew; Forster, Ronald; Eu, Mingda

Ethylene oxide (ETO) is commonly used to sterilize plastic containers, but the effects of residual amounts left after sterilization on protein therapeutics are still not well understood. Here we focus primarily on the factors that influence concentrations of ETO migrating from ETO-treated plastic containers into aqueous solution. A study was designed to investigate the kinetics of this process at various temperatures, and the kinetic data could be fit with a model based on a combination of Fickean diffusion and first-order chemical reaction (to account for observed hydrolysis of ETO). The diffusion and reaction rate constants thus obtained obey Arrhenius-like temperature dependence. These results indicate that for analytical methods involving extraction into water, measurements of residual ETO in a container must account for the effects of ETO hydrolysis. Further, the effects of salt concentration and pH of the fluid in the container on accumulated ETO levels were explored. Finally, interactions of ETO with anti-streptavidin (AntiSA) Immunoglobulin G1 (IgG1) and IgG2 antibodies were studied, with ETO adducts found on all methionine residues when incubated in solutions spiked with ETO at concentrations that could be reached (based on the kinetic studies) in ETO-treated plastic vials. Overall, the likelihood of observable ETO-protein modifications upon storage in ETO-sterilized containers will depend on a complex interplay of protein properties, formulation details, storage conditions, and amount of residual ETO initially in the container. Ethylene oxide (ETO) is commonly used to sterilize plastic containers, but the effects of residual amounts left after sterilization on protein therapeutics are still not well understood. Here we describe experiments exploring the factors that influence concentrations of ETO migrating from ETO-treated plastic containers into aqueous solution over time. Additionally, interactions of ETO with model antibodies were studied, with ETO adducts found on all methionine residues when incubated in solutions spiked with ETO at concentrations that could potentially be reached in ETO-treated plastic vials. Overall, the likelihood of observable ETO-protein modifications upon storage in ETO-sterilized containers will depend on a complex interplay of protein properties, formulation details, storage conditions, and amount of residual ETO initially in the container. © PDA, Inc. 2017.

Tabletted microspheres containing Cynara scolymus (var. Spinoso sardo) extract for the preparation of controlled release nutraceutical matrices.

PubMed

Gavini, E; Alamanni, M C; Cossu, M; Giunchedi, P

2005-08-01

Controlled release dosage forms based on tabletted microspheres containing fresh artichoke Cynara scolymus extract were performed for the oral administration of a nutritional supplement. Microspheres were prepared using a spray-drying technique; lactose or hypromellose have been chosen as excipients. Microspheres were characterized in terms of encapsulated extract content, size and morphology. Qualitative and quantitative composition of the extract before and after the spray process was determined. Compressed matrices (tablets) were prepared by direct compression of the spray-dried microspheres. In vitro release tests of microparticles and tablets prepared were carried out in both acidic and neutral media. Spray-drying is a good method to prepare microspheres containing the artichoke extract. The microspheres encapsulate an amount of extract close to the theoretical value. Particle size analyses indicate that the microparticles have dvs of approximately 6-7 microm. Electronic microscopy observations reveal that particles based on lactose have spherical shape and particles containing hypromellose are almost collapsed. The hydroalcoholic extract is stable to the microsphere production process: its polyphenolic composition (qualitative and quantitative) did not change after spraying. In vitro release studies show that microparticles characterized by a quick polyphenolic release both in acidic and neutral media due to the high water solubility of the carrier lactose. On the contrary, microspheres based hypromellose release only 20% of the loaded extract at pH 1.2 in 2 h and the total amount of polyphenols is released only after about further 6 h at pH 6.8. Matrices prepared tabletting lactose microspheres and hypromellose microparticles in the weight ratio 1:1 show a slow release rate, that lasts approximately 24 h. This one-a-day sustained release formulation containing Cynara scolymus extract could be proposed as a nutraceutical controlled release dosage form for oral administration.

Presence of nano-sized silica during in vitro digestion of foods containing silica as a food additive.

PubMed

Peters, Ruud; Kramer, Evelien; Oomen, Agnes G; Rivera, Zahira E Herrera; Oegema, Gerlof; Tromp, Peter C; Fokkink, Remco; Rietveld, Anton; Marvin, Hans J P; Weigel, Stefan; Peijnenburg, Ad A C M; Bouwmeester, Hans

2012-03-27

The presence, dissolution, agglomeration state, and release of materials in the nano-size range from food containing engineered nanoparticles during human digestion is a key question for the safety assessment of these materials. We used an in vitro model to mimic the human digestion. Food products subjected to in vitro digestion included (i) hot water, (ii) coffee with powdered creamer, (iii) instant soup, and (iv) pancake which either contained silica as the food additive E551, or to which a form of synthetic amorphous silica or 32 nm SiO(2) particles were added. The results showed that, in the mouth stage of the digestion, nano-sized silica particles with a size range of 5-50 and 50-500 nm were present in food products containing E551 or added synthetic amorphous silica. However, during the successive gastric digestion stage, this nano-sized silica was no longer present for the food matrices coffee and instant soup, while low amounts were found for pancakes. Additional experiments showed that the absence of nano-sized silica in the gastric stage can be contributed to an effect of low pH combined with high electrolyte concentrations in the gastric digestion stage. Large silica agglomerates are formed under these conditions as determined by DLS and SEM experiments and explained theoretically by the extended DLVO theory. Importantly, in the subsequent intestinal digestion stage, the nano-sized silica particles reappeared again, even in amounts higher than in the saliva (mouth) digestion stage. These findings suggest that, upon consumption of foods containing E551, the gut epithelium is most likely exposed to nano-sized silica. © 2012 American Chemical Society

[Determination of alpha-gliadin content in gluten-containing and gluten-free heated food].

PubMed

Meier, P; Windemann, H; Baumgartner, E

1984-05-01

The amount of alpha-gliadin and whole gliadin in bread dough after heating at temperatures of 50-100 degrees C was determined by ELISA. At temperatures above 80 degrees C the amount which could be found was greatly reduced. In pasta foods containing wheat (with a max. drying temperature of 75 degrees C) alpha-gliadin could be determined totally but in wheat bread (crust and crumb) only 0.5-40% of the content in the original flour was found. The results of an analysis of "gluten-free" pasta foods on the market and the amounts of alpha-gliadin found are discussed in relation to the recommendations of the Codex alimentarius (WHO).

Solid fuel volatilization to produce synthesis gas

DOEpatents

Schmidt, Lanny D.; Dauenhauer, Paul J.; Degenstein, Nick J.; Dreyer, Brandon J.; Colby, Joshua L.

2014-07-29

A method comprising contacting a carbon and hydrogen-containing solid fuel and a metal-based catalyst in the presence of oxygen to produce hydrogen gas and carbon monoxide gas, wherein the contacting occurs at a temperature sufficiently high to prevent char formation in an amount capable of stopping production of the hydrogen gas and the carbon monoxide gas is provided. In one embodiment, the metal-based catalyst comprises a rhodium-cerium catalyst. Embodiments further include a system for producing syngas. The systems and methods described herein provide shorter residence time and high selectivity for hydrogen and carbon monoxide.

Highly nitrogen-doped porous carbon derived from zeolitic imidazolate framework-8 for CO2 capture.

PubMed

Ma, Xiancheng; Li, Liqing; Chen, Ruofei; Wang, Chunhao; Li, Haoyang; Li, Hailong

2018-05-18

CO2 adsorption capacity of nitrogen-doped porous carbon depends to a large nitrogen doping levels and high surface area in previous studies. However, it seems difficult to incorporate large amounts of nitrogen while maintaining a high surface area and pore structure. Here we have reported porous carbon having a nitrogen content of up to 25.52% and specific surface area of 948 m2 g-1, which is prepared by pyrolyzing the nitrogen-containing zeolite imidazole framework-8 and urea composite at 650 °C under a nitrogen atmosphere. ZNC650 exhibits a superior CO2 uptake of 3.7 mmol g-1 at 25 ℃ and 1 bar. Experimental and theoretical results indicate that the nitrogen-containing functional groups can enhance CO2 uptake electrostatic interactions, Lewis acid-base interactions and hydrogen-bonding interactions, which are elucidated by density functional theory calculations. As CO2 adsorbent materials, these carbons have excellent adsorption capacity. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Retention of mercury by salmon

USGS Publications Warehouse

Amend, Donald F.

1970-01-01

Consuming fish that have been exposed repeatedly to mercury derivatives is a potential public health hazard because fish can accumulate and retain mercury in their tissues (Rucker, 1968). Concern has been expressed in the United States because mercurials have been used extensively in industry and as prophylactic and therapeutic agents in fish hatcheries. Rucker and Amend (1969) showed that yearling rainbow trout (Salmo gairdneri) and chinook salmon (Oncorhynchus tshawytscha) exposed to mercurials accumulated excessive amounts of mercury in many tissues. Further, Rucker and Amend (1969) concluded that wild fish that ate mercury-contaminated fish also could contain high mercury levels. Although mercury was eliminated from most tissues within several months, substantial levels remained in the kidney for more than 33 weeks after the last exposure. Since high levels of mercury can be retained in the kidney for an undetermined time, it is possible that returning adult salmon exposed to mercurials as juveniles could constitute a potential hazard to public health. The purpose of this study was to determine whether such fish contained high residual levels of mercury.

Microstructural characterization of low and high carbon CoCrMo alloy nanoparticles produced by mechanical milling

NASA Astrophysics Data System (ADS)

Simoes, T. A.; Goode, A. E.; Porter, A. E.; Ryan, M. P.; Milne, S. J.; Brown, A. P.; Brydson, R. M. D.

2014-06-01

CoCrMo alloys are utilised as the main material in hip prostheses. The link between this type of hip prosthesis and chronic pain remains unclear. Studies suggest that wear debris generated in-vivo may be related to post-operative complications such as inflammation. These alloys can contain different amounts of carbon, which improves the mechanical properties of the alloy. However, the formation of carbides could become sites that initiate corrosion, releasing ions and/or particles into the human body. This study analysed the mechanical milling of alloys containing both high and low carbon levels in relevant biological media, as an alternative route to generate wear debris. The results show that low carbon alloys produce significantly more nanoparticles than high carbon alloys. During the milling process, strain induces an fcc to hcp phase transformation. Evidence for cobalt and molybdenum dissolution in the presence of serum was confirmed by ICP-MS and TEM EDX techniques.

7 CFR 58.730 - Filling containers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Filling containers. 58.730 Section 58.730 Agriculture... Procedures § 58.730 Filling containers. Hot fluid cheese from the cookers may be held in hotwells or hoppers... shall effectively measure the desired amount of product into the pouch or container in a sanitary manner...

Water and coffee in beverage container during STS-9 flight

NASA Image and Video Library

1983-11-28

STS009-126-456 (28 Nov 1983) --- Water and coffee in beverage container during STS-9 flight. An extra amount of hydrogen in the H2O is believed to be the reason for the bubbling, distended effect in the container.

Absence of sugars in electrophoretically purified cytochrome b5 demonstrated by combined gas chromatography-mass spectrometry

PubMed Central

1981-01-01

The problem of determining small but significant amounts of carbohydrates, in purified proteins, has been studied using the membrane protein, cytochrome b5. A newly developed method that involves direct gas chromatography-mass spectrometry of sugars obtained by hydrolysis of proteins purified by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS PAGE) allows the identification and determination of small amounts of carbohydrates (e.g., 20 micrograms of glycoprotein containing a minimum of 0.1% monosaccharide), even in the presence of relatively high amounts of impurities. Application of this method to cytochrome b5 fragments obtained by tryptic digestion from rat liver microsomes and purified by combined gel filtration and ion exchange chromatography, followed by SDS PAGE, has consistently yielded values below 0.07 mol of the individual sugars and aminosugars per mole cytochrome b5. It is concluded that cytochrome b5, at least its trypsin-released major amino- terminal fragment, is not constitutively glycosylated. PMID:7251667

Application of Time-resolved PIV to Supersonic Hot Jets

NASA Technical Reports Server (NTRS)

Bridges, James; Wernet, Mark P.

2007-01-01

This presentation lays out the ground-breaking work at bringing high-speed (25kHz) particle image velocimetry (PIV) to bear on measurements of noise-producing turbulence in hot jets. The work is still in progress in that the tremendous amount of data obtained are still be analyzed, but the method has been validated and initial results of interest to jet noise modeling have been obtained. After a brief demonstration of the validation process used on the data, results are shown for hot jets at different temperatures and Mach numbers. Comparisons of first order statistics show the relative indifference of the turbulence to the presence of shocks and independence to jet temperature. What does come out is that when the shock-containing jets are in a screech mode the turbulence is highly elevated, showing the importance of removing screech phenomena from model-scale jets before applying findings to full-scale aircraft which typically do not contain shocks.

Polinsar Experiments of Multi-Mode X-Band Data Over South Area of China

NASA Astrophysics Data System (ADS)

Lu, L.; Yan, Q.; Duan, M.; Zhang, Y.

2012-08-01

This paper makes the polarimetric and polarimetric interferometric synthetic aperture radar (PolInSAR) experiments with the high-resolution X-band data acquired by Multi-mode airborne SAR system over an area around Linshui, south of China containing tropic vegetation and urban areas. Polarimetric analysis for typical tropic vegetations and man-made objects are presented, some polarimetric descriptors sensitive to vegetations and man-made objects are selected. Then, the PolInSAR information contained in the data is investigated, considering characteristics of the Multi-mode-XSAR dataset, a dual-baseline polarimetric interferometry method is proposed in this paper. The method both guarantees the high coherence on fully polarimetric data and combines the benefits of short and long baseline that helpful to the phase unwrapping and height sensitivity promotion. PolInSAR experiment results displayed demonstrates Multi-mode-XSAR datasets have intuitive capabilities for amount of application of land classification, objects detection and DSM mapping.

Glycerosomes: Use of hydrogenated soy phosphatidylcholine mixture and its effect on vesicle features and diclofenac skin penetration.

PubMed

Manca, Maria Letizia; Cencetti, Claudia; Matricardi, Pietro; Castangia, Ines; Zaru, Marco; Sales, Octavio Diez; Nacher, Amparo; Valenti, Donatella; Maccioni, Anna Maria; Fadda, Anna Maria; Manconi, Maria

2016-09-10

In this work, diclofenac was encapsulated, as sodium salt, in glycerosomes containing 10, 20 or 30% of glycerol in the water phase with the aim to ameliorate its topical efficacy. Taking into account previous findings, glycerosome formulation was modified, in terms of economic suitability, using a cheap and commercially available mixture of hydrogenated soy phosphatidylcholine (P90H). P90H glycerosomes were spherical and multilamellar; photon correlation spectroscopy showed that obtained vesicles were ∼131nm, slightly larger and more polydispersed than those made with dipalmitoylphosphatidylcholine (DPPC) but, surprisingly, they were able to ameliorate the local delivery of diclofenac, which was improved with respect to previous findings, in particular using glycerosomes containing high amount of glycerol (20 and 30%). Finally, this drug delivery system showed a high in vitro biocompatibility toward human keratinocytes. Copyright © 2016 Elsevier B.V. All rights reserved.

Phosphate glass useful in high power lasers

DOEpatents

Hayden, Joseph S.; Sapak, David L.; Ward, Julia M.

1990-01-01

A low- or no-silica phosphate glass useful as a laser medium and having a high thermal conductivity, K.sub.90.degree. C. >0.8 W/mK, and a low coefficient of thermal expansion, .alpha..sub.20.degree.-40.degree. C. <80.times.10.sup.-7 /.degree.C., consists essentially of (on a batch composition basis): the amounts of Li.sub.2 O and Na.sub.2 O providing an average alkali metal ionic radius sufficiently low whereby said glass has K.sub.90.degree. C. >0.8 W/mK and .alpha..sub.20.degree.-40.degree. C. <80.times.10.sup.-7 /.degree.C., and wherein, when the batch composition is melted in contact with a silica-containing surface, the final glass composition contains at most about 3.5 mole % of additional silica derived from such contact during melting. The Nd.sub.2 O.sub.3 can be replaced by other lasing species.

Recycling of solid waste rich in organic nitrogen from leather industry: mineral nutrition of rice plants.

PubMed

Nogueira, Francisco G E; Castro, Isabela A; Bastos, Ana R R; Souza, Guilherme A; de Carvalho, Janice G; Oliveira, Luiz C A

2011-02-28

The leather industry produces a large quantity of solid waste (wet blue leather), which contains a high amount of chromium. After its removal from wet blue leather, a solid collagenic material is recovered, containing high nitrogen levels, which can be used as a nitrogen source in agriculture. In order to take more advantage of the collagen, it was enriched with mineral P and K in order to produce NPK formulations. The objective was also to evaluate the efficiency of such formulations as a nutrient supply for rice plants in an Oxisoil, under greenhouse conditions. The application of PK enriched-collagen formulations resulted in N contents in the vegetative parts and grains of rice plants which were equivalent or superior to those obtained with urea and commercial NPK formulations. Copyright © 2010 Elsevier B.V. All rights reserved.

Modified Phenylethynyl Containing Imides for Secondary Bonding: Non-Autoclave, Low Temperature Processable Adhesives

NASA Technical Reports Server (NTRS)

Dezern, James F. (Technical Monitor); Chang, Alice C.

1999-01-01

As part of a program to develop structural adhesives for high performance aerospace applications, research continued on the development of modified phenylethynyl containing imides, LaRC(trademark)MPEIs. In previous reports, the polymer properties were controlled by varying the molecular weight, the amount of branching, and the phenylethynyl content and by blending with low molecular weight materials. This research involves changing the flexibility in the copolyimide backbone of the branched, phenylethynyl terminated adhesives. These adhesives exhibit excellent processability at pressures as low as 15 psi and temperatures as low as 288 C. The Ti/Ti lap shear specimens are processable in an autoclave or a temperature programmable oven under a vacuum bag at 288-300 C without external pressure. The cured polymers exhibit high mechanical properties and excellent solvent resistance. The chemistry and properties of these adhesives are presented.

Coffee and its waste repel gravid Aedes albopictus females and inhibit the development of their embryos.

PubMed

Satho, Tomomitsu; Dieng, Hamady; Ahmad, Muhammad Hishamuddin Itam; Ellias, Salbiah Binti; Hassan, Ahmad Abu; Abang, Fatimah; Ghani, Idris Abd; Miake, Fumio; Ahmad, Hamdan; Fukumitsu, Yuki; Zuharah, Wan Fatma; Majid, Abdul Hafiz Ab; Kassim, Nur Faeza Abu; Hashim, Nur Aida; Ajibola, Olaide Olawunmi; Al-Khayyat, Fatima Abdulla; Nolasco-Hipolito, Cirilo

2015-05-14

Dengue is a prevalent arboviral disease and the development of insecticide resistance among its vectors impedes endeavors to control it. Coffee is drunk by millions of people daily worldwide, which is associated with the discarding of large amounts of waste. Coffee and its waste contain large amounts of chemicals many of which are highly toxic and none of which have a history of resistance in mosquitoes. Once in solution, coffee is brownish in colour, resembling leaf infusion, which is highly attractive to gravid mosquitoes. To anticipate the environmental issues related to the increasing popularity of coffee as a drink, and also to combat insecticide resistance, we explored the deterrence potentials of coffee leachates against the ovipositing and embryonic stages of the dengue vector, Aedes albopictus. In a series of choice, no-choice, and embryo toxicity bioassays, we examined changes in the ovipositional behaviours and larval eclosion of Ae. albopictus in response to coffee extracts at different concentrations. Oviposition responses were extremely low when ovicups holding highly concentrated extract (HCE) of coffee were the only oviposition sites. Gravid females retained increased numbers of mature eggs until 5 days post-blood feeding. When provided an opportunity to oviposit in cups containing coffee extracts and with water, egg deposition occurred at lower rates in those containing coffee, and HCE cups were far less attractive to females than those containing water only. Females that successfully developed in a coffee environment preferentially oviposited in such cups when in competition with preferred oviposition sites (water cups), but this trait did not continue into the fourth generation. Larval eclosion occurred at lower rates among eggs that matured in a coffee environment, especially among those that were maintained on HCE-moistened substrates. The observations of the present study indicate a pronounced vulnerability of Ae. albopictus to the presence of coffee in its habitats during the early phases of its life cycle. The observations that coffee repels gravid females and inhibits larval eclosion provide novel possibilities in the search for novel oviposition deterrents and anti-larval eclosion agents against dengue vectors.

UNCOMPAHGRE PRIMITIVE AREA, COLORADO.

USGS Publications Warehouse

Luedke, R.G.; Sheridan, M.J.

1984-01-01

A mineral-resource study was made of that part of the Uncompahgre National Forest, Colorado constituting the officially designated primitive area. Because the primitive area and its southern border zone contained operating mines producing gold, silver, copper, lead, zinc, and minor amounts of a few other metals, and had been a part of a highly productive mining region, the area was concluded to have large segments of both probable and substantiated mineral-resource potential. No energy resources were identified in the study.

First results from the AMY detector at Tristan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imlay, R.

1987-08-01

Bhabha scattering and multi-hadronic e/sup +/e/sup -/ annihilation events have been observed in the AMY detector at ..sqrt..s = 500 GeV at the TRISTAN e/sup +/e/sup -/ storage ring. Here the authors report the results of a preliminary analysis of the properties of these events. Of particular note is one event that contains a high energy, isolated gamma ray together with a large amount of missing momentum that penetrates the fiducial volume of the detector.

NICKEL-BASE ALLOY

DOEpatents

Inouye, H.; Manly, W.D.; Roche, T.K.

1960-01-19

A nickel-base alloy was developed which is particularly useful for the containment of molten fluoride salts in reactors. The alloy is resistant to both salt corrosion and oxidation and may be used at temperatures as high as 1800 deg F. Basically, the alloy consists of 15 to 22 wt.% molybdenum, a small amount of carbon, and 6 to 8 wt.% chromium, the balance being nickel. Up to 4 wt.% of tungsten, tantalum, vanadium, or niobium may be added to strengthen the alloy.

Retrieval of constituent mixing ratios from limb thermal emission spectra

NASA Technical Reports Server (NTRS)

Shaffer, William A.; Kunde, Virgil G.; Conrath, Barney J.

1988-01-01

An onion-peeling iterative, least-squares relaxation method to retrieve mixing ratio profiles from limb thermal emission spectra is presented. The method has been tested on synthetic data, containing various amounts of added random noise for O3, HNO3, and N2O. The retrieval method is used to obtain O3 and HNO3 mixing ratio profiles from high-resolution thermal emission spectra. Results of the retrievals compare favorably with those obtained previously.