Reduction of carbon content in waste-tire combustion ashes by bio-thermal treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, C.C.; Lee, W.J.; Shih, S.I.

2009-07-01

Application of bio-catalyst (NOE-7F) in thermal treatment can adequately dispose dark-black fly ashes from co-combustion of both waste tires and coal. After thermal treatment of fly ashes by adding 10% NOE-7F, the carbon contents reduced by 37.6% and the weight losses increased by 405%, compared with the fly ashes without mixing with NOE-7F. The combustion behaviors of wasted tires combustion fly ashes with NOE-7F were also investigated by both thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The results verify that NOE-7F has positive effects on the combustion of residual carbon and toxic polycyclic aromatic hydrocarbons (PAHs) enhance the energymore » release and reduce the toxicity during the process of thermal treatment. Furthermore, using NOE-7F to dispose high-carbon content fly ashes did improve the compressive strength of fly ashes and concrete mixtures. Therefore, NOE-7F is a promising additive which could decrease treatment cost of high-carbon content fly ashes and reduce the amount of survival toxic PAHs.« less

Removal of introduced inorganic content from chipped forest residues via air classification

DOE PAGES

Lacey, Jeffrey A.; Aston, John E.; Westover, Tyler L.; ...

2015-08-04

Inorganic content in biomass decreases the efficiency of conversion processes, especially thermochemical conversions. The combined concentrations of specific ash forming elements are the primary attributes that cause pine residues to be considered a degraded energy conversion feedstock, as compared to clean pine. Air classification is a potentially effective and economical tool to isolate high inorganic content biomass fractions away from primary feedstock sources to reduce their ash content. In this work, loblolly pine forest residues were air classified into 10 fractions whose ash content and composition were measured. Ash concentrations were highest in the lightest fractions (5.8–8.5 wt%), and inmore » a heavy fraction of the fines (8.9–15.1 wt%). The removal of fractions with high inorganic content resulted in a substantial reduction in the ash content of the remaining biomass in forest thinnings (1.69–1.07 wt%) and logging residues (1.09–0.68 wt%). These high inorganic content fractions from both forest residue types represented less than 7.0 wt% of the total biomass, yet they contained greater than 40% of the ash content by mass. Elemental analysis of the air classified fractions revealed the lightest fractions were comprised of high concentrations of soil elements (silicon, aluminum, iron, sodium, and titanium). However, the elements of biological origin including calcium, potassium, magnesium, sulfur, manganese, and phosphorous were evenly distributed throughout all air classified fractions, making them more difficult to isolate into fractions with high mineral concentrations. Under the conditions reported in this study, an economic analysis revealed air classification could be used for ash removal for as little as $2.23 per ton of product biomass. As a result, this study suggests air classification is a potentially attractive technology for the removal of introduced soil minerals from pine forest residues.« less

21 CFR 168.122 - Lactose.

Code of Federal Regulations, 2010 CFR

2010-04-01

.../m), calculated on a dry basis. (2) The sulfated ash content is not more than 0.3 percent, m/m... action to final action. (3) Sulfated ash content, section 31.014, “Ash of Sugars and Sirups,” Final Action, Sulfated Ash, 14th Ed. (1984), p. 575. (4) pH, section 14.022, “pH of Flour, Potentiometric...

21 CFR 168.122 - Lactose.

Code of Federal Regulations, 2011 CFR

2011-04-01

.../m), calculated on a dry basis. (2) The sulfated ash content is not more than 0.3 percent, m/m... action to final action. (3) Sulfated ash content, section 31.014, “Ash of Sugars and Sirups,” Final Action, Sulfated Ash, 14th Ed. (1984), p. 575. (4) pH, section 14.022, “pH of Flour, Potentiometric...

Geohydrologic data from test hole USW UZ-7, Yucca Mountain area, Nye County, Nevada

USGS Publications Warehouse

Kume, Jack; Hammermeister, D.P.

1990-01-01

This report contains a description of the methods used in drilling and coring of the test-hole USW UZ-7, a description of the methods used in collecting, handling, and testing of test-hole samples; Lithologic information from the test hole; and water-content, water-potential, bulk-density, grain-density, porosity, and tritium data for the test hole. Test-hole USW UZ-7 was drilled and cored to a total depth of 62.94 m. The drilling was done using air as a drilling fluid to minimize disturbance to the water content of cores, drill-bit cuttings, and borehole wall-rock. Beginning at the land surface, the unsaturated-zone rock that was penetrated consisted of alluvium; welded and partially to nonwelded ash-flow tuff; bedded and reworked ash-fall tuff; nonwelded ash-flow tuff; and welded ash-flow tuff. Values of gravimetric water content and water potential of alluvium were intermediate between the extreme values in welded and nonwelded units of tuff. Gravimetric water content was largest in bedded and nonwelded ash-fall tuffs and was smallest in welded ash-flow tuff. Values of water potential were more negative in densely welded ash-flow tuffs and were less negative in bedded and nonwelded ash-fall tuffs. Bulk density was largest in densely welded ash-flow tuffs and smallest in nonwelded and bedded ash-fall tuffs. Grain density was uniform but was slightly larger in nonwelded and bedded ash-fall tuffs than in welded ash-flow tuffs. Porosity trends were opposite to bulk-density trends. Tritium content in alluvium was smallest near the alluvium-bedrock contact, markedly increased in the middle of the deposit, and decreased in the near-surface zone of the deposit. (Author 's abstract)

Combined disc pelletisation and thermal treatment of MSWI fly ash.

PubMed

Huber, Florian; Herzel, Hannes; Adam, Christian; Mallow, Ole; Blasenbauer, Dominik; Fellner, Johann

2018-03-01

An environmentally friendly and cost efficient way for the management of municipal solid waste incineration (MSWI) fly ash represents its thermal co-treatment together with combustible waste. However, the safe introduction and storage of MSWI fly ash in the waste bunker is challenging and associated with severe problems (e.g. dust emissions, generation of undefined lumps and heat in case of moistened MSWI fly ash). Therefore, the aim of this study is to investigate the suitability of pelletisation as a pretreatment of MSWI fly ash. In particular, MSWI fly ash was characterised after sampling, pelletisation and thermal treatment and the transfer of constituents to secondary fly ash and flue gas was investigated. For this purpose, MSWI fly ash pellets with a water content of about 0.15 kg/kg and a diameter of about 8 mm have been produced by disc pelletiser and treated in an electrically heated pilot-scale rotary kiln at different temperatures, ranging from 450 °C to 1050 °C. The total contents of selected elements in the MSWI fly ash before and after thermal treatment and in the generated secondary fly ash have been analysed in order to understand the fate of each element. Furthermore, leachable contents of selected elements and total content of persistent organic pollutants of the thermally treated MSWI fly ash were determined. Due to the low total content of Hg (0.7 mg/kg) and the low leachate content of Pb (<0.36 mg/kg), even at the lowest treatment temperature of 450 °C, thermally treated MSWI fly ash pellets can be classified as non-hazardous waste. However, temperatures of at least 650 °C are necessary to decrease the toxic equivalency of PCDD/F and DL-PCB. The removal of toxic heavy metals like Cd and Pb is significantly improved at temperatures of 850 °C, 950 °C or even 1050 °C. The observed metal removal led to relatively high contents of e.g. Cu (up to 11,000 mg/kg), Pb (up to 91,000 mg/kg) and Zn (up to 21,000 mg/kg) in the secondary fly ash. This metal enriched secondary fly ash might represent a potential raw material for metal recovery (e.g. via acidic leaching). Due to the high content of total dissolved solids observed in the leachate of thermally treated MSWI fly ash pellets, a wet extraction procedure is suggested to enable its safe disposal at non-hazardous waste landfills. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optoelectronic system of online measurements of unburned carbon in coal fly ash

NASA Astrophysics Data System (ADS)

Golas, Janusz; Jankowski, Henryk; Niewczas, Bogdan; Piechna, Janusz; Skiba, Antoni; Szkutnik, Wojciech; Szkutnik, Zdzislaw P.; Wartak, Ryszarda; Worek, Cezary

2001-08-01

Carbon-in-ash level is an important consideration for combustion efficiency as well as ash marketing. The optoelectronic analyzing system for on-line determination and monitoring of the u burned carbon content of ash samples is presented. The apparatus operates on the principle that carbon content is proportional to the reflectance of IR light. Ash samples are collected iso kinetically from the flue gas duct and placed in a sample tube with a flat glass bottom. The same is then exposed to a light. The reflectance intensity is used by the system's computer to determine residual carbon content from correlation curves. The sample is then air purged back to the duct or to the attached sample canister to enable laboratory check analysis. The total cycle time takes between 5 and 10 minutes. Real time result of carbon content with accuracy 0.3-0.7 percent are reported and can be used for boiler controlling.

Ash content: its effect on combustion of corn plants

Treesearch

A. Broido; M. A. Nelson

1964-01-01

Two corn plant samples, one cut in the fall while green, the other after weathering over the winter, exhibited strikingly different combustion properties. The increased susceptibility to flaming combustion of the spring-harvested sample is attributable to its decreased ash content, and not directly to its moisture content.

Briquettes of rice husk, polyethylene terephthalate (PET), and dried leaves as implementation of wastes recycling

NASA Astrophysics Data System (ADS)

Hariyanto, Sucipto; Usman, Mohammad Nurdianfajar; Citrasari, Nita

2017-06-01

This research aim is to determine the best briquettes as implementation of wastes recycle based on scoring method, main component composition, compressive strength, caloric value, water content, vollatile content, and ash content, also the suitability with SNI 01-6235-2000. Main component that used are rice husk, 2mm and 6 mm PET, and dried leaves. Composition variation in this research are marked as K1, K2, K3, K4, and K5 with 2 mm PET plastic and K1, K2, K3, K4, and K5 with 6 mm PET plastic. The total weight of the briquettes is 100 g and divided into 90% main components and 10% tapioca as binder. The compressive strength, caloric value, water content, vollatile content, and ash content were tested according to ASTM D 5865-04, ASTM D 3173-03, ASTM D 3175-02, ASTM D 3174-02. The tested results were used to determine the best briquette by scoring method, and the chosen briquettes is K2 with 6 mm PET plastic. The composition is 70% rice husk, 20% 6 mm PET plastic, and 10% dried leaves with the compressive strength, caloric value, water content, vollatile content, and ash content value is 51,55 kg/cm2; 5123 kal/g; 3,049%; 31,823%, dan 12,869%. The suitable value that meet the criteria according to SNI 01-6235-2000 is compressive strength, caloric value, water content, and ash content.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burgess, R.M.; Perron, M.M.; Friedman, C.L.

Approaches for cleaning up contaminated sediments range from dredging to in situ treatment. In this study, we discuss the effects of amending reference and contaminated sediments with coal fly ash to reduce the bioavailability and toxicity of a field sediment contaminated with polycyclic aromatic hydrocarbons (PAHs). Six fly ashes and a coconut charcoal were evaluated in 7-d whole sediment toxicity tests with a marine amphipod (Ampelisca abdita) and mysid (Americamysis bahia). Fly ashes with high carbon content and the coconut charcoal showed proficiency at reducing toxicity. Some of the fly ashes demonstrated toxicity in the reference treatments. It is suspectedmore » that some of this toxicity is related to the presence of ammonia associated with fly ashes as a result of postoxidation treatment to reduce nitrous oxide emissions. Relatively simple methods exist to remove ammonia from fly ash before use, and fly ashes with low ammonia content are available. Fly ashes were also shown to effectively reduce overlying water concentrations of several PAHs. No evidence was seen of the release of the metals cadmium, copper, nickel, or lead from the fly ashes. A preliminary 28-d polychaete bioaccumulation study with one of the high-carbon fly ashes and a reference sediment was also performed. Although preliminary, no evidence was seen of adverse effects to worm growth or lipid content or of accumulation of PAHs or mercury from exposure to the fly ash. These data show fly ashes with high carbon content could represent viable remedial materials for reducing the bioavailability of organic contaminants in sediments.« less

On-line determination of the ash content in coal using industrial, natural gamma-ray equipment

NASA Astrophysics Data System (ADS)

Alvarez, M. C.; Dopico, M. T.

1995-12-01

This work presents phases of an investigation carried out in Spain to develop industrial natural-γ equipment to determine the ash content in coals. Initially the programme was on a laboratory scale and later tests were performed in a coal washing plant on a mixture of washed products. The results obtained are very satisfactory since the equipment permits the ash content to be determined with a mean error of 1.3% and a SD of 1.

Firing system modification to alter ash properties for reduction of deposition and slagging under low NOx firing conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, D.; Lewis, R.; Tobiasz, R.

1998-07-01

The composition and properties of ash formed during coal firing have a major impact on boiler performance. Higher ash content in the coal can mean higher costs associated with coal handling, transportation, ash removal and ash disposal along with higher costs due to the increased ash content's deleterious effects on pulverizing, combustion and heat transfer. ABB C-E Services, Inc. has conducted research what might be done to minimize the adverse effects of ash on boiler performance for many years. Recently, ABB C-E Services has studied the effects of firing system modifications on ash composition and properties and the effect thesemore » firing system modifications have on overall furnace performance. The subject of this paper is the impact of the installation of the CFS{trademark} yaw angles were varied and particle samples were collected at the waterwalls for the different yaw angles tested. These ash samples were analyzed for ash composition. The results showed that with a larger CFS{trademark} yaw angle (the air stream directed more towards the boiler walls) the base/acid ratio, iron content and sulfur content of the particle samples collected at the waterwall were reduced. This effect is due to several contributing factors: (1) an oxidizing environment produced by injecting more air toward the walls; and (2) an aerodynamic change which impacts the particle combustion time/temperature history.« less

Study on Strength Behavior of Organic Soil Stabilized with Fly Ash

PubMed Central

Molla, Md. Keramat Ali; Sarkar, Grytan

2017-01-01

The aim of this study is to investigate the effect of fly ash on the consistency, compactness, acidic properties, and strength of organic soil. The presence of organic content in the soil has detrimental impacts on the physical and strength behavior of soil. To investigate the effectiveness of fly ash in the stabilization of organic soil, two types of fly ashes (Type I and Type II) at different percentages were used. It is found that fly ash significantly reduces the plasticity index of the organic soil, whereas the liquid and plastic limits increase. The dry density of the fly ash-soil mixture increases significantly, while the water requirement reduces due to the addition of fly ash. The increase of dry density compromises higher strength. The increase of qu with the increase of fly ash content is mainly due to the pozzolanic reaction of fly ash, although the reduction in water content results from the addition of dry fly ash solid. Moreover, Type I fly ash contributes a higher value of qu compared to Type II fly ash. This is attributed to the characteristics of fly ash including CaO and CaO/SiO2 ratio. PMID:29085881

Enhanced Ethanol Production from De-Ashed Paper Sludge by Simultaneous Saccharification and Fermentation and Simultaneous Saccharification and Co-Fermentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, L.; Wang, W.; Pallapolu, V. R.

2011-11-01

A previous study demonstrated that paper sludges with high ash contents can be converted to ethanol by simultaneous saccharification and fermentation (SSF) or simultaneous saccharification and co-fermentation (SSCF). High ash content in the sludge, however, limited solid loading in the bioreactor, causing low product concentration. To overcome this problem, sludges were de-ashed before SSF and SSCF. Low ash content in sludges also increased the ethanol yield to the extent that the enzyme dosage required to achieve 70% yield in the fermentation process was reduced by 30%. High solid loading in SSF and SSCF decreased the ethanol yield. High agitation andmore » de-ashing of the sludges were able to restore the part of the yield loss caused by high solid loading. Substitution of the laboratory fermentation medium (peptone and yeast extract) with corn steep liquor did not bring about any adverse effects in the fermentation. Fed-batch operation of the SSCF and SSF using low-ash content sludges was effective in raising the ethanol concentration, achieving 47.8 g/L and 60.0 g/L, respectively.« less

EVALUATION OF THE EFFECTS OF COAL FLY ASH AMENDMENTS ON THE TOXICITY OF A CONTAMINATED MARINE SEDIMENT

PubMed Central

Burgess, Robert M.; Perron, Monique M.; Friedman, Carey L.; Suuberg, Eric M.; Pennell, Kelly G.; Cantwell, Mark G.; Pelletier, Marguerite C.; Ho, Kay T.; Serbst, Jonathan R.; Ryba, Stephan A.

2013-01-01

Approaches for cleaning-up contaminated sediments range from dredging to in situ treatment. In the present report, we discuss the effects of amending reference and contaminated sediments with coal fly ash to reduce the bioavailability and toxicity of a field sediment contaminated with polycyclic aromatic hydrocarbons (PAHs). Six fly ashes and a coconut charcoal were evaluated in 7 d whole sediment toxicity tests with a marine amphipod (Ampelisca abdita) and mysid (Americamysis bahia). Fly ashes with high carbon content and the coconut charcoal showed proficiency at reducing toxicity. Some of the fly ashes demonstrated toxicity in the reference treatments. It is suspected that some of this toxicity is related to the presence of ammonia associated with fly ashes as a result of post-oxidation treatment to reduce nitrous oxides emissions. Relatively simple methods exist to remove ammonia from fly ash prior to use and fly ashes with low ammonia content are available. Fly ashes were also shown to effectively reduce overlying water concentrations of several PAHs. There was no evidence of the release of the metals cadmium, copper, nickel or lead from the fly ashes. A preliminary 28 d polychaete bioaccumulation study with one of the high carbon fly ashes and a reference sediment was also performed. Although preliminary, there was no evidence of adverse effects to worm growth or lipid content, or the accumulation of PAHs or mercury from exposure to the fly ash. These data show fly ashes with high carbon contents may represent viable remedial materials for reducing the bioavailability of organic contaminants in sediments. PMID:18717615

Ash reduction strategies in corn stover facilitated by anatomical and size fractionation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lacey, Jeffrey A.; Emerson, Rachel M.; Thompson, David N.

There is growing interest internationally to produce fuels from renewable biomass resources. Inorganic components of biomass feedstocks, referred to collectively as ash, damage equipment and decrease yields in thermal conversion processes, and decrease feedstock value for biochemical conversion processes. Decreasing the ash content of feedstocks improves conversion efficiency and lowers process costs. Because physiological ash is unevenly distributed in the plant, mechanical processes can be used to separate fractions of the plant based on ash content. This study focuses on the ash separation that can be achieved by separating corn stover by particle size and anatomical fraction. Baled corn stovermore » was hand-separated into anatomical fractions, ground to <19.1 mm, and size separated using six sieves ranging from 9.5 to 0.150 mm. Size fractions were analyzed for total ash content and ash composition. Particle size distributions observed for the anatomical fractions varied considerably. Cob particles were primarily 2.0 mm or greater, while most of the sheath and husk particles were 2.0 mm and smaller. Particles of leaves greater than 0.6 mm contained the greatest amount of total ash, ranging from approximately 8 to 13% dry weight of the total original material, while the fractions with particles smaller than 0.6 mm contained less than 2% of the total ash of the original material. As a result, based on the overall ash content and the elemental ash, specific anatomical and size fractions can be separated to optimize the feedstocks being delivered to biofuels conversion processes and minimize the need for more expensive ash reduction treatments.« less

Ash reduction strategies in corn stover facilitated by anatomical and size fractionation

DOE PAGES

Lacey, Jeffrey A.; Emerson, Rachel M.; Thompson, David N.; ...

2016-04-22

There is growing interest internationally to produce fuels from renewable biomass resources. Inorganic components of biomass feedstocks, referred to collectively as ash, damage equipment and decrease yields in thermal conversion processes, and decrease feedstock value for biochemical conversion processes. Decreasing the ash content of feedstocks improves conversion efficiency and lowers process costs. Because physiological ash is unevenly distributed in the plant, mechanical processes can be used to separate fractions of the plant based on ash content. This study focuses on the ash separation that can be achieved by separating corn stover by particle size and anatomical fraction. Baled corn stovermore » was hand-separated into anatomical fractions, ground to <19.1 mm, and size separated using six sieves ranging from 9.5 to 0.150 mm. Size fractions were analyzed for total ash content and ash composition. Particle size distributions observed for the anatomical fractions varied considerably. Cob particles were primarily 2.0 mm or greater, while most of the sheath and husk particles were 2.0 mm and smaller. Particles of leaves greater than 0.6 mm contained the greatest amount of total ash, ranging from approximately 8 to 13% dry weight of the total original material, while the fractions with particles smaller than 0.6 mm contained less than 2% of the total ash of the original material. As a result, based on the overall ash content and the elemental ash, specific anatomical and size fractions can be separated to optimize the feedstocks being delivered to biofuels conversion processes and minimize the need for more expensive ash reduction treatments.« less

Finite element analysis on flexural behavior of high ductility of fiber reinforced concrete beam

NASA Astrophysics Data System (ADS)

Zhou, Mohan; Chi, Cuiping; Pei, Changchun

2017-03-01

In this paper, finite element software is used to simulate and analyze ECC beams. With the ratio of water-binder, fiber content and the content of fly ash as variables, the initial cracking moments, the yield moments, the initial cracking deflections, and the yield deflections of the ECC beams are studied. The results show that the lower the water-binder ratio is, the better the beam performance is; When the fiber content is 13kg/m3, the mechanical properties of the ECC beams are the lowest, and then strengthen; When the content of fly ash increase, the bending moment of the specimen beam becomes smaller and the deflection tends to increase, however the deflection of the fly ash decreases when the content of fly ash is higher than 1300kg/m3 in the initial cracking. According to the formula of ordinary concrete ultimate load capacity, the formula of yield capacity of ECC beam is deduced.

The combined effects of ionizing radiation and weightlessness on calcium and phosphorus content in the mineral fraction of the calcified tissues in the rat skeleton

NASA Technical Reports Server (NTRS)

Prokhonchukov, A. A.; Komissarova, N. A.; Kolesnik, A. G.; Novikov, L. L.

1980-01-01

Phosphorus and calcium content in the ash from skeletal bones (ribs, scapula, vertebra, and crus) of 30 rats exposed to ionizing radiation (800 rads) on the flight of the Kosmos 690 biosatellite was studied. A 10 percent decrease in ash content coefficient and 29 percent decrease in phosphorus content was found immediately after the flight, and a 9 percent decrease in phosphorus content persisted after 26 days of readaptation to terrestrial conditions.

Chemical composition and some trace element contents in coals and coal ash from Tamnava-Zapadno Polje Coal Field, Serbia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vukasinovic-Pesic, V.; Rajakovic, L.J.

2009-07-01

The chemical compositions and trace element contents (Zn, Cu, Co, Cr, Ni, Pb, Cd, As, B, Hg, Sr, Se, Be, Ba, Mn, Th, V, U) in coal and coal ash samples from Tamnava-Zapadno Polje coal field in Serbia were studied. The coal from this field belongs to lignite. This high volatility coal has high moisture and low S contents, moderate ash yield, and high calorific value. The coal ash is abundant in alumosilicates. Many trace elements such as Ni > Cd > Cr > B > As > Cu > Co > Pb > V > Zn > Mn inmore » the coal and Ni > Cr > As > B > Cu > Co = Pb > V > Zn > Mn in the coal ash are enriched in comparison with Clarke concentrations.« less

The effect of organic wheat flour by-products on sourdough performances assessed by a multi-criteria approach.

PubMed

Clément, Héliciane; Prost, Carole; Chiron, Hubert; Ducasse, Maren Bonnand; Della Valle, Guy; Courcoux, Philippe; Onno, Bernard

2018-04-01

In this study, we determined the effect of organic (i) flour ash content (1%-1.4%) and (ii) flour by-product addition (bran, shorts and germ) on sourdough performances. After five consecutive back-sloppings, sourdough was used for bread-making and its bread-related properties were assessed. No effect of flour composition factors (i & ii) on sourdough lactic acid bacteria and yeasts were highlighted. Nonetheless, they greatly altered lactic acid and acetic acid sourdough contents from 6.9 to 17.4 g/kg and from 0.9 to 2.2 g/kg, respectively. The flour ash content (i) had a significant and positive effect on sourdough acidity and CO 2 production. Bread made with sourdough with a high ash content had a significantly higher acidity and specific volume. These physicochemical differences between breads were perceived by sensory evaluation in a significant way. Sourdough supplemented (ii) with germ had higher lactic acid and carbon dioxide contents than sourdough supplemented with bran and shorts. Hence, flour composition, combining ash content and flour by-products, appears to be an effective factor to obtain a better control of sourdough performances. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization and partitioning of the char ash collected after the processing of pine wood chips in a pilot-scale gasification unit

Treesearch

Thomas L. Eberhardt; Hui Pan; Leslie H. Groom; Chi-Leung So

2011-01-01

Southern yellow pine wood chips were used as the feedstock for a pilot-scale gasification unit coupled with a 25 kW generator. The pulp-grade wood chips were relatively free of bark and low in ash content. Processing this feedstock yielded a black/sooty by-product that upon combustion in a muffle furnace resulted in an ash content of about 48%. The term "char ash...

Changes in kenaf properties and chemistry as a function of growing time

Treesearch

Roger M. Rowell; James S. Han

1999-01-01

Kenaf Tainung 1 cultivar was grown in Madison, WI in 1994. The ratio of core to bast fiber, total plant yield, protein, ash, fiber length, extractives, lignin, and sugar content were determined as a function of growing age. Ash, protein, extractives, L-arabinose, L-rhamnose, D-galactose, and D-mannose contents decreased while lignin, D-glucose and D-xylose content...

The impacts of biomass properties on pyrolysis yields, economic and environmental performance of the pyrolysis-bioenergy-biochar platform to carbon negative energy.

PubMed

Li, Wenqin; Dang, Qi; Brown, Robert C; Laird, David; Wright, Mark M

2017-10-01

This study evaluated the impact of biomass properties on the pyrolysis product yields, economic and environmental performance for the pyrolysis-biochar-bioenergy platform. We developed and applied a fast pyrolysis, feedstock-sensitive, regression-based chemical process model to 346 different feedstocks, which were grouped into five types: woody, stalk/cob/ear, grass/plant, organic residue/product and husk/shell/pit. The results show that biomass ash content of 0.3-7.7wt% increases biochar yield from 0.13 to 0.16kg/kg of biomass, and decreases biofuel yields from 87.3 to 40.7 gallons per tonne. Higher O/C ratio (0.88-1.12) in biomass decreases biochar yield and increases biofuel yields within the same ash content level. Higher ash content of biomass increases minimum fuel selling price (MFSP), while higher O/C ratio of biomass decreases MFSP within the same ash content level. The impact of ash and O/C ratio of biomass on GHG emissions are not consistent for all feedstocks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact of Collection Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

DOE Office of Scientific and Technical Information (OSTI.GOV)

William Smith; Jeffery Einerson; Kevin Kenney

2014-09-01

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment testedmore » included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg-1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.« less

Investigating Electrostatic Precipitator Design Parameters for Efficient Control of Particulate Matter in Thermal Power Plant: A Case Study

NASA Astrophysics Data System (ADS)

Rai, P.; Gautam, N.; Chandra, H.

2018-06-01

This work deals with the analysis and modification of operational parameters for meeting the emission standards, set by Central Pollution Control Board (CPCB)/State Pollution Control Board (SPCB) from time to time of electrostatic precipitator (ESP). The analysis is carried out by using standard chemical analysis supplemented by the relevant data collected from Korba East Phase (Ph)-III thermal power plant, under Chhattisgarh State Electricity Board (CSEB) operating at Korba, Chhattisgarh. Chemical analysis is used to predict the emission level for different parameters of ESP. The results reveal that for a constant outlet PM concentration and fly ash percentage, the total collection area decreases with the increase in migration velocity. For constant migration velocity and outlet PM concentration, the total collection area increases with the increase in the fly ash percent. For constant migration velocity and outlet e PM concentration, the total collection area increases with the ash content in the coal. i.e. from minimum ash to maximum ash. As far as the efficiency is concerned, it increases with the fly ash percent, ash content and the inlet dust concentration but decreases with the outlet PM concentration at constant migration velocity, fly ash and ash content.

Investigating Electrostatic Precipitator Design Parameters for Efficient Control of Particulate Matter in Thermal Power Plant: A Case Study

NASA Astrophysics Data System (ADS)

Rai, P.; Gautam, N.; Chandra, H.

2018-02-01

This work deals with the analysis and modification of operational parameters for meeting the emission standards, set by Central Pollution Control Board (CPCB)/State Pollution Control Board (SPCB) from time to time of electrostatic precipitator (ESP). The analysis is carried out by using standard chemical analysis supplemented by the relevant data collected from Korba East Phase (Ph)-III thermal power plant, under Chhattisgarh State Electricity Board (CSEB) operating at Korba, Chhattisgarh. Chemical analysis is used to predict the emission level for different parameters of ESP. The results reveal that for a constant outlet PM concentration and fly ash percentage, the total collection area decreases with the increase in migration velocity. For constant migration velocity and outlet PM concentration, the total collection area increases with the increase in the fly ash percent. For constant migration velocity and outlet e PM concentration, the total collection area increases with the ash content in the coal. i.e. from minimum ash to maximum ash. As far as the efficiency is concerned, it increases with the fly ash percent, ash content and the inlet dust concentration but decreases with the outlet PM concentration at constant migration velocity, fly ash and ash content.

Effect of lime and wood ash on the nixtamalization of maize and tortilla chemical and nutritional characteristics.

PubMed

Pappa, María Renée; de Palomo, Patricia Palacios; Bressani, Ricardo

2010-06-01

The objective of the study was to obtain information on the chemical composition, functional properties, sensory quality and protein value of tortillas made from the nixtamalization of maize using either lime or wood ashes. The Ca, K, Mg, Fe, and Zn content of lime and wood ashes showed lime to be high in Ca content while wood ash contained more K and about 71% of the Ca content of lime. Both contained relatively high levels of Mg, Fe and Zn, but more so in the wood ashes. The level of reagent for nixtamalization was set at 0.8% of the maize weight. All other processing conditions were kept constant. The pH of the cooking solution was 12.0 for lime and 10.9 for wood ash. The moisture content of maize at 60 min of cooking was 45.8% for both treatments, however after 12 h of soaking, moisture level was 51.0% for the lime treatment and only 46.8% for the ash treatment. Solids (2.4%) in the lime cooking liquor were higher than in the wood ash liquor (1.0%). Chemical composition changes were similar between treatments in masa and tortilla; however, both masa and tortillas absorbed relatively high levels of all minerals including Fe and Zn from the wood ash treatment. The different treatment influenced functional properties particularly hardness and color. Tortilla characteristics were also similar. Protein quality of both alkali cooked products was lower than that of raw corn, more so the product from the wood ash treatment. Although some differences were observed in the sensory studies, human subjects did not dislike the wood ash made tortillas.

Mercury retention by fly ashes from coal combustion: Influence of the unburned carbon content

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lopez-Anton, M.A.; Diaz-Somoano, M.; Martinez-Tarazona, M.R.

2007-01-31

The objective of this study was to evaluate the effect of unburned carbon particles present in fly ashes produced by coal combustion on mercury retention. To achieve this objective, the work was divided into two parts. The aim of the first part of the study was to estimate the amount of mercury captured by the fly ashes during combustion in power stations and the relationship of this retention to the unburned carbon content. The second part was a laboratory-scale study aimed at evaluating the retention of mercury concentrations greater than those produced in power stations by fly ashes of differentmore » characteristics and by unburned carbon particles. From the results obtained it can be inferred that the unburned carbon content is not the only variable that controls mercury capture in fly ashes. The textural characteristics of these unburned particles and of other components of fly ashes also influence retention.« less

The Effect of Ash and Inorganic Pigment Fill on the Atomic Oxygen Erosion of Polymers and Paints (ISMSE-12)

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Simmons, Julie C.; de Groh, Kim K.; Miller, Sharon K.

2012-01-01

Low atomic oxygen fluence (below 1x10(exp 20) atoms/sq cm) exposure of polymers and paints that have a small ash content and/or inorganic pigment fill does not cause a significant difference in erosion yield compared to unfilled (neat) polymers or paints. However, if the ash and/or inorganic pigment content is increased, the surface population of the inorganic content will begin to occupy a significant fraction of the surface area as the atomic oxygen exposure increases because the ash is not volatile and remains as a loosely attached surface layer. This results in a reduction of the flux of atomic oxygen reacting with the polymer and a reduction in the rate of erosion of the polymer remaining. This paper presents the results of ground laboratory and low Earth orbital (LEO) investigations to evaluate the fluence dependence of atomic oxygen erosion yields of polymers and paints having inorganic fill content.

Optimization of isolation of cellulose from orange peel using sodium hydroxide and chelating agents.

PubMed

Bicu, Ioan; Mustata, Fanica

2013-10-15

Response surface methodology was used to optimize cellulose recovery from orange peel using sodium hydroxide (NaOH) as isolation reagent, and to minimize its ash content using ethylenediaminetetraacetic acid (EDTA) as chelating agent. The independent variables were NaOH charge, EDTA charge and cooking time. Other two constant parameters were cooking temperature (98 °C) and liquid-to-solid ratio (7.5). The dependent variables were cellulose yield and ash content. A second-order polynomial model was used for plotting response surfaces and for determining optimum cooking conditions. The analysis of coefficient values for independent variables in the regression equation showed that NaOH and EDTA charges were major factors influencing the cellulose yield and ash content, respectively. Optimum conditions were defined by: NaOH charge 38.2%, EDTA charge 9.56%, and cooking time 317 min. The predicted cellulose yield was 24.06% and ash content 0.69%. A good agreement between the experimental values and the predicted was observed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Geotechnical properties of ash deposits near Hilo, Hawaii

USGS Publications Warehouse

Wieczorek, G.F.; Jibson, R.W.; Wilson, R.C.; Buchanan-Banks, J. M.

1982-01-01

Two holes were hand augered and sampled in ash deposits near Hilo, Hawaii. Color, water content and sensitivity of the ash were measured in the field. The ash alternated between reddish brown and dark reddish brown in color and had water contents as high as 392%. A downhole vane shear device measured sensitivities as high as 6.9. A series of laboratory tests including grain size distribution, Atterberg limits, X-ray diffraction analysis, total carbon determination, vane shear, direct shear and triaxial tests were performed to determine the composition and geotechnical properties of the ash. The ash is very fine grained, highly plastic and composed mostly of gibbsite and amorphous material presumably allophane. The ash has a high angle of internal friction ranging from 40-43? and is classified as medium to very sensitive. A series of different ash layers was distinguished on the basis of plasticity and other geotechnical properties. Sensitivity may be due to a metastable fabric, cementation, leaching, high organic content, and thixotropy. The sensitivity of the volcanic ash deposits near Hilo is consistent with documented slope instability during earthquakes in Hawaii. The high angles of internal friction and cementation permit very steep slopes under static conditions. However, because of high sensitivity of the ash, these slopes are particularly susceptible to seismically-induced landsliding.

Energy properties of solid fossil fuels and solid biofuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holubcik, Michal, E-mail: michal.holubcik@fstroj.uniza.sk; Jandacka, Jozef, E-mail: jozef.jandacka@fstroj.uniza.sk; Kolkova, Zuzana, E-mail: zuzana.kolkova@rc.uniza.sk

The paper deals about the problematic of energy properties of solid biofuels in comparison with solid fossil fuels. Biofuels are alternative to fossil fuels and their properties are very similar. During the experiments were done in detail experiments to obtain various properties of spruce wood pellets and wheat straw pellets like biofuels in comparison with brown coal and black coal like fossil fuels. There were tested moisture content, volatile content, fixed carbon content, ash content, elementary analysis (C, H, N, S content) and ash fusion temperatures. The results show that biofuels have some advantages and also disadvantages in comparison withmore » solid fossil fuels.« less

[Effects of stabilization treatment on migration and transformation of heavy metals in mineral waste residues].

PubMed

Zhao, Shu-Hua; Chen, Zhi-Liang; Zhang, Tai-Ping; Pan, Wei-Bin; Peng, Xiao-Chun; Che, Rong; Ou, Ying-Juan; Lei, Guo-Jian; Zhou, Ding

2014-04-01

Different forms of heavy metals in soil will produce different environmental effects, and will directly influence the toxicity, migration and bioavailability of heavy metals. This study used lime, fly ash, dried sludge, peanut shells as stabilizers in the treatment of heavy metals in mineral waste residues. Morphological analyses of heavy metal, leaching experiments, potted plant experiments were carried out to analyze the migration and transformation of heavy metals. The results showed that after adding stabilizers, the pH of the acidic mineral waste residues increased to more than neutral, and the organic matter content increased significantly. The main existing forms of As, Pb, and Zn in the mineral waste residues were the residual. The contents of exchangeable and organic matter-bound As decreased by 65.6% and 87.7% respectively after adding fly ash, dried sludge and peanut shells. Adding lime, fly ash and peanut shells promoted the transformation of As from the Fe-Mn oxide-bound to the carbonate-bound, and adding lime and fly ash promoted the transformation of Pb and Zn from the exchangeable, Fe-Mn oxide-bound, organic matter-bound to the residual. After the early stage of the stabilization treatment, the contents of As, Pb and Zn in the leachate had varying degrees of decline, and adding peanut shells could reduce the contents of As, Pb and Zn in the leachate further. Among them, the content of As decreased most significantly after treatment with fly ash, dried sludge and peanut shells, with a decline of 57.4%. After treatment with lime, fly ash and peanut shells, the content of Zn decreased most significantly, by 24.9%. The addition of stabilizers was advantageous to the germination and growth of plants. The combination of fly ash, dried sludge and peanut shell produced the best effect, and the Vetiveria zizanioides germination rate reached 76% in the treated wasted mineral residues.

Ash Analysis

NASA Astrophysics Data System (ADS)

Marshall, Maurice R.

Ash refers to the inorganic residue remaining after either ignition or complete oxidation of organic matter in a foodstuff. A basic knowledge of the characteristics of various ashing procedures and types of equipment is essential to ensure reliable results. Two major types of ashing are used: dry ashing, primarily for proximate composition and for some types of specific mineral analyses; wet ashing (oxidation), as a preparation for the analysis of certain minerals. Microwave systems now are available for both dry and wet ashing, to speed the processes. Most dry samples (i.e., whole grain, cereals, dried vegetables) need no preparation, while fresh vegetables need to be dried prior to ashing. High-fat products such as meats may need to be dried and fat extracted before ashing. The ash content of foods can be expressed on either a wet weight (as is) or on a dry weight basis. For general and food-specific information on measuring ash content, see references (1-11).

Proximate composition of several fish from Jatigede Reservoir in Sumedang district, West Java

NASA Astrophysics Data System (ADS)

Herawati, T.; Yustiati, A.; Nurhayati, A.; Mustikawati, R.

2018-04-01

The aim of research is to determine the nutritional contents of fishes in the Jatigede Reservoir, the research uses survey method from November 2016 to October 2017. Sample collecting is done in the Wado district and Jatigede district. Samples are identified by its species and the nutritional contents are determined. The analyzed parameter includes water content, ash content, crude fiber content, protein content, fat content and carbohydrate content. Research shows that the nutritional contents of 13 species of fish vary. The water contents ranges between 67.50 % to 77.75 %, the highest percentage found in Chana striata. Ash contents ranges between 1.25 % to 4.87 %, the highest percentage found in Rasbora argyrotaenia, Crude fiber percentage cannot be found. Protein ranges between 14.43% to 21.93 %, the highest percentage found in Chanos chanos, Fat ranges 0.72 % to 6.86 %, the highest percentage found in Hampala macrolepidota. Carbohydrate ranges between 0.12 % to 2.64 %, the highest percentage found in Osteochillus vittatus.

Valorization of MSWI bottom ash for biogas desulfurization: Influence of biogas water content.

PubMed

Fontseré Obis, Marta; Germain, Patrick; Troesch, Olivier; Spillemaecker, Michel; Benbelkacem, Hassen

2017-02-01

In this study an alternative valorization of Municipal Solid Waste Incineration (MSWI) Bottom Ash (BA) for H 2 S elimination from landfill biogas was evaluated. Emphasis was given to the influence of water content in biogas on H 2 S removal efficiency by BA. A small-scale pilot was developed and implemented in a landfill site located in France. A new biogas analyzer was used and allowed real-time continuous measurement of CH 4 , CO 2 , O 2 , H 2 S and H 2 O in raw and treated biogas. The H 2 S removal efficiency of bottom ash was evaluated for different inlet biogas humidities: from 4 to 24g water /m 3 . The biogas water content was found to greatly affect bottom ash efficiency regarding H 2 S removal. With humid inlet biogas the H 2 S removal was almost 3 times higher than with a dry inlet biogas. Best removal capacity obtained was 56gH 2 S/kgdryBA. A humid inlet biogas allows to conserve the bottom ash moisture content for a maximum H 2 S retention. Copyright © 2016 Elsevier Ltd. All rights reserved.

EFFECTS OF IRON CONTENT IN COAL COMBUSTION FLY ASHES ON SPECIATION OF MERCURY

EPA Science Inventory

The paper discusses the effects of iron content in coal combustion fly ashes on speciation of mercury. (NOTE: The chemical form of mercury species in combustion flue gases is an important influence on the control of mercury emissions from coal combustion). The study focused on th...

Correlation of concentration of modified cassava flour for banana fritter flour using simple linear regression

NASA Astrophysics Data System (ADS)

Herminiati, A.; Rahman, T.; Turmala, E.; Fitriany, C. G.

2017-12-01

The purpose of this study was to determine the correlation of different concentrations of modified cassava flour that was processed for banana fritter flour. The research method consists of two stages: (1) to determine the different types of flour: cassava flour, modified cassava flour-A (using the method of the lactid acid bacteria), and modified cassava flour-B (using the method of the autoclaving cooling cycle), then conducted on organoleptic test and physicochemical analysis; (2) to determine the correlation of concentration of modified cassava flour for banana fritter flour, by design was used simple linear regression. The factors were used different concentrations of modified cassava flour-B (y1) 40%, (y2) 50%, and (y3) 60%. The response in the study includes physical analysis (whiteness of flour, water holding capacity-WHC, oil holding capacity-OHC), chemical analysis (moisture content, ash content, crude fiber content, starch content), and organoleptic (color, aroma, taste, texture). The results showed that the type of flour selected from the organoleptic test was modified cassava flour-B. Analysis results of modified cassava flour-B component containing whiteness of flour 60.42%; WHC 41.17%; OHC 21.15%; moisture content 4.4%; ash content 1.75%; crude fiber content 1.86%; starch content 67.31%. The different concentrations of modified cassava flour-B with the results of the analysis provides correlation to the whiteness of flour, WHC, OHC, moisture content, ash content, crude fiber content, and starch content. The different concentrations of modified cassava flour-B does not affect the color, aroma, taste, and texture.

Reburning Characteristics of Residual Carbon in Fly Ash from CFB Boilers

NASA Astrophysics Data System (ADS)

Zhang, S. H.; Luo, H. H.; Chen, H. P.; Yang, H. P.; Wang, X. H.

The content of residual carbon in fly ash of CFB boilers is a litter high especially when low-grade coal, such as lean coal, anthracite coal, gangue, etc. is in service, which greatly influences the efficiency of boilers and fly ash further disposal. Reburn of fly ash through collection, recirculation in CFB furnace or external combustor is a possibly effective strategy to decrease the carbon content, mainly depending on the residual carbon reactivity. In this work, the combustion properties of residual carbon in fly ash and corresponding original coal from large commercial CFB boilers (Kaifeng (440t/h), and Fenyi (410t/h), all in china) are comparably investigated through experiments. The residual carbon involved was firstly extracted and enriched from fly ash by means of floating elutriation to mitigate the influence of ash and minerals on the combustion behavior of residual carbon. Then, the combustion characteristic of two residual carbons and the original coal particles was analyzed with thermogravimetric analyzer (TGA, STA409C from Nestch, Germany). It was observed that the ignition temperature of the residual carbon is much higher than that of original coal sample, and the combustion reactivity of residual carbon is not only dependent on the original coal property, but also the operating conditions. The influence of oxygen content and heating rate was also studied in TGA. The O2 concentration is set as 20%, 30%, 40% and 70% respectively in O2/N2 gas mixture with the flow rate of 100ml/min. It was found that higher oxygen content is favor for decreasing ignition temperature, accelerating the combustion rate of residual carbon. And about 40% of oxygen concentration is experimentally suggested as an optimal value when oxygen-enriched combustion is put into practice for decreasing residual carbon content of fly ash in CFB boilers.

Potential of phosphorus recovery from sewage sludge and manure ash by thermochemical treatment.

PubMed

Havukainen, Jouni; Nguyen, Mai Thanh; Hermann, Ludwig; Horttanainen, Mika; Mikkilä, Mirja; Deviatkin, Ivan; Linnanen, Lassi

2016-03-01

All life forms require phosphorus (P), which has no substitute in food production. The risk of phosphorus loss from soil and limited P rock reserves has led to the development of recycling P from industrial residues. This study investigates the potential of phosphorus recovery from sewage sludge and manure ash by thermochemical treatment (ASH DEC) in Finland. An ASH DEC plant could receive 46-76 kt/a of sewage sludge ash to produce 51-85 kt/a of a P-rich product with a P2O5 content of 13-18%, while 320-750 kt/a of manure ash could be supplied to produce 350-830 kt/a of a P-rich product with a P content of 4-5%. The P2O5 potential in the total P-rich product from the ASH DEC process using sewage sludge and manure ash is estimated to be 25-47 kt/a, which is significantly more than the P fertilizer demand in Finland's agricultural industries. The energy efficiency of integrated incineration and the ASH DEC process is more dependent on the total solid content and the subsequent need for mechanical dewatering and thermal drying than on the energy required by the ASH DEC process. According to the results of this study, the treated sewage sludge and manure ash using the ASH DEC process represent significant potential phosphorus sources for P fertilizer production. Copyright © 2016 Elsevier Ltd. All rights reserved.

MINERAL AND BIOCHEMICAL ANALYSIS OF VARIOUS PARTS OF CISSUS QUADRANGULARIS LINN

PubMed Central

Udayakumar, R.; Sundaran, M.; Krishna, Raghuram

2004-01-01

Ash, minerals and biochemical contents were determined in various parts of root, stem and leaf of Cissus quadrangularis. The maximum ash content was observed in the root. The maximum concentration of carbohydrate and protein in the root and phosphorus, iron, calcium and lipids in the stem were observed. PMID:22557157

Ozone and sulfur dioxide effects on tall fescue. II. Alteration of quality constituents. [Festuca arundinacea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flagler, R.B.; Youngner, V.B.

A greenhouse study was conducted to determine whether ozone (O/sub 3/) and sulfur dioxide (SO/sub 2/) might alter forage quality parameters of tall fescue (Festuca arundinacea Schreb. Alta). Plants were exposed weekly to four O/sub 3/ treatments, 0, 0.10, 0.20, and 0.30 ..mu..L L/sup -1/; with or without 0.10 ..mu..L L/sup -1/ SO/sub 2/, 6 h d/sup -1/ for 12 weeks. Ozone had a much greater impact on forage quality than did SO/sub 2/. Ozone increased protein content on a g kg/sup -1/ basis and decreased protein on a weight per plant basis. Ozone reduced crude fat, crude fiber, andmore » total nonstructural carbohydrate contents of the forage. Crude ash content increased due to O/sub 3/ exposure. On a weight per plant basis, O/sub 3/ decreased the forage concentration of Ca, Mg, and P. Ozone increased Ca concentration of herbage. Sulfur dioxide increased ash content of the forage. Phosphorus concentration and weight per plant of Mg and P were all reduced by SO/sub 2/ Significant pollutant interactions occurred for crude fiber, crude ash, total Mg, and total P contents of forage. While treatments resulted in some apparent increases in forage quality, these were at the expense of yield. The most adverse effects on forage quality were an increase in ash content which resulted from an interaction of SO/sub 2/ with O/sub 3/, and a reduction in soluble carbohydrate content of shoots due to O/sub 3/.« less

The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

NASA Astrophysics Data System (ADS)

Saputra, Asep Handaya; Putri, Rizky Anggreini

2017-05-01

Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

Growth and elemental accumulation of plants grown in acidic soil amended with coal fly ash-sewage sludge co-compost

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, J.W.C.; Selvam, A.

2009-10-15

A greenhouse experiment was conducted to evaluate the growth and heavy-metal accumulation of Brassica chinensis and Agropyron elongatum in 10 and 25% ash-sludge co-compost (ASC)-amended loamy acidic soil (pH 4.51) at two different application rates: 20% and 40% (v/v). Soil pH increased, whereas electrical conductivity decreased with the amendment of ASC to soil. Bioavailable Cu, Zn, and Mn contents of ASC-amended soil decreased, whereas Ni, Pb, and B contents increased. Concentrations of bioavailable Cu, Zn, and Mn in sludge compost (SC)-amended soils were 5.57, 20.8, and 8.19 mg kg{sup -1}, respectively. These concentrations were significantly lower than those in soilmore » receiving an application rate of 20 or 25% ASC as 2.64, 8.48, and 5.26 mg kg(-1), respectively. Heavy metals and B contents of the composting mass significantly increased with an increase in ASC application rate from 20 to 40% (6.2 to 16.6 mg kg{sup -1} for 10% ASC- and 9.4 to 18.6 mg kg{sup -1} for 25% ASC-amended soil. However, when the ash content in co-compost increased from 10 to 25% during composting, bioavailable heavy-metal contents decreased. However, B contents increased with an increase in ash content. Addition of co-composts increased the dry-weight yield of the plants, and this increase was more obvious as the ash amendment rate in the co-composts and the ASC application rate increased. In case of B. chinensis, the biomass of 2.84 g/plant for 40% application of 25% ASC was significantly higher than SC (0.352 g/plant), which was 40% application of 10% ASC (0.434 g/plant) treatments. However, in A. elongatum, the differences between biomass of plants grown with 10% (1.34-1.94 g/ plant) and 25% ASC (2.12-2.21 g/plant) were not significantly different. ASC was favorable in increasing the growth of B. chinensis and A. elongatum. The optimal ash amendment to the sludge composting and ASC application rates were at 25 and 20%, respectively.« less

Prewashing enhances the liquid hot water pretreatment efficiency of waste wheat straw with high free ash content.

PubMed

Huang, Chen; Wu, Xinxing; Huang, Yang; Lai, Chenhuan; Li, Xin; Yong, Qiang

2016-11-01

The effect of prewashing process prior to the liquid hot water (LHW) pretreatment of high free ash content waste wheat straw (WWS) was investigated. It was found that prewashing process decreased the ash content of WWS greatly, from 29.48% to 9.82%. This contributed to the lower pH value of prehydrolyzate and higher xylan removal in the following LHW pretreatment. More importantly, the prewashing process effectively increased the cellulose enzymatic hydrolysis efficiency of pretreated WWS, from 53.04% to 84.15%. The acid buffering capacity (ABC) and cation exchange capacity (CEC) of raw and prewashed WWS were examined. The majority of free ash removal from WWS by prewashing resulted in the decrease of the ABC of the WWS from 211.74 to 61.81mmol/pH-kg, and potentially enhancing the efficiency of the follow-up LHW pretreatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fractionation and Mobility of Thallium in Volcanic Ashes after Eruption of Eyjafjallajökull (2010) in Iceland.

PubMed

Karbowska, Bozena; Zembrzuski, Wlodzimierz

2016-07-01

Volcanic ash contains thallium (Tl), which is highly toxic to the biosphere. The aim of this study was to determine the Tl concentration in fractions of volcanic ash samples originating from the Eyjafjallajökull volcano. A sequential extraction scheme allowed for a study of element migration in the environment. Differential pulse anodic stripping voltammetry using a flow measuring system was selected as the analytical method to determine Tl content. The highest average content of Tl in volcanic ash was determined in the fraction entrapped in the aluminosilicate matrix (0.329 µg g(-1)), followed by the oxidizable fraction (0.173 µg g(-1)). The lowest content of Tl was found in the water soluble fraction (0.001 µg g(-1)); however, this fraction is important due to the fact that Tl redistribution among all the fractions occurs through the aqueous phase.

Composition and trace element content of coal in Taiwan

USGS Publications Warehouse

Tsai, L.-Y.; Chen, C.-F.; Finkelman, R.B.

2005-01-01

To investigate the trace element contents of local coal, four coal samples were collected from operating mines in NW Taiwan. Detailed petrographic and chemical characterization analyses were then conducted. Analytical results indicate that (1) the samples were high volatile bituminous coal in rank with ash content ranging from 4.2 to 14.4% and with moisture content ranging from 2.7 to 4.6%; (2) the macerals were mostly composed of vitrinite with vitrinite reflectance less than 0.8%; (3) the sample of Wukeng mine has the highest Fe2O3 (29.5%), TI (54.8 ppm), Zn (140 ppm), and As (697 ppm) contents in ash and Hg (2.3 ppm) in the coal. If used properly, these coals should not present health hazards.

High-volume fly ash concrete.

DOT National Transportation Integrated Search

2013-06-01

The objective of the proposed study is to design, test, and evaluate high-volume fly ash concrete mixtures. Traditional specifications : limit the amount of fly ash to 40% or less cement replacement. This program attempts to increase the ash content ...

The design of control system of livestock feeding processing

NASA Astrophysics Data System (ADS)

Sihombing, Juna; Napitupulu, Humala L.; Hidayati, Juliza

2018-03-01

PT. XYZ is a company that produces animal feed. One type of animal feed produced is 105 ISA P. In carrying out its production process, PT. XYZ faces the problem of rejected feed amounts during 2014 to June 2015 due to the amount of animal feed that exceeds the standard feed quality of 13% of moisture content and 3% for ash content. Therefore, the researchers analyzed the relationship between factors affecting the quality and extent of damage by using regression and correlation and determine the optimum value of each processing process. Analysis results found that variables affecting product quality are mixing time, steam conditioning temperature and cooling time. The most dominant variable affecting the product moisture content is mixing time with the correlation coefficient of (0.7959) and the most dominant variable affecting the ash content of the product during the processing is mixing time with the correlation coefficient of (0.8541). The design of the proposed product processing control is to run the product processing process with mixing time 235 seconds, steam conditioning temperature 87 0C and cooling time 192 seconds. Product quality 105 ISA P obtained by using this design is with 12.16% moisture content and ash content of 2.59%.

[Effects of Chinese prickly ash orchard on soil organic carbon mineralization and labile organic carbon in karst rocky desertification region of Guizhou province].

PubMed

Zhang, Wen-Juan; Liao, Hong-Kai; Long, Jian; Li, Juan; Liu, Ling-Fei

2015-03-01

Taking 5-year-old Chinese prickly ash orchard (PO-5), 17-year-old Chinese prickly ash orchard (PO- 17), 30-year-old Chinese prickly ash orchard (PO-30) and the forest land (FL, about 60 years) in typical demonstration area of desertification control test in southwestern Guizhou as our research objects, the aim of this study using a batch incubation experiment was to research the mineralization characteristics of soil organic carbon and changes of the labile soil organic carbon contents at different depths (0-15 cm, 15-30 cm, and 30-50 cm). The results showed that: the cumulative mineralization amounts of soil organic carbon were in the order of 30-year-old Chinese prickly ash orchard, the forest land, 5-year-old Chinese prickly ash orchard and 17-year-old Chinese prickly ash orchard at corresponding depth. Distribution ratios of CO2-C cumulative mineralization amount to SOC contents were higher in Chinese prickly ash orchards than in forest land at each depth. Cultivation of Chinese prickly ash in long-term enhanced the mineralization of soil organic carbon, and decreased the stability of soil organic carbon. Readily oxidized carbon and particulate organic carbon in forest land soils were significantly more than those in Chinese prickly ash orchards at each depth (P < 0.05). With the increasing times of cultivation of Chinese prickly ash, the contents of readily oxidized carbon and particulate organic carbon first increased and then declined at 0-15 cm and 15-30 cm depth, respectively, but an opposite trend was found at 30-50 cm depth. At 0-15 cm and 15-30 cm, cultivation of Chinese prickly ash could be good for improving the contents of labile soil organic carbon in short term, but it was not conducive in long-term. In this study, we found that cultivation of Chinese prickly ash was beneficial for the accumulation of labile organic carbon at the 30-50 cm depth.

Nutritional attributes of ash (Fraxinus spp.) outer bark and phloem and their relationships to resistance against the emerald ash borer.

PubMed

Hill, Amy L; Whitehill, Justin G A; Opiyo, Stephen O; Phelan, P Larry; Bonello, Pierluigi

2012-12-01

The emerald ash borer (Agrilus planipennis Fairmaire, EAB) is an alien, invasive wood-boring insect that is responsible for killing millions of ash trees since its discovery in North America in 2002. All North American ash species (Fraxinus spp.) that EAB has encountered have shown various degrees of susceptibility, while Manchurian ash (Fraxinus mandshurica Ruprecht), which shares a co-evolutionary history with this insect, is resistant. Recent studies have looked into constitutive resistance mechanisms in Manchurian ash, concentrating on the secondary phloem, which is the feeding substrate for the insect. In addition to specialized metabolism and defense-related components, primary metabolites and nutritional summaries can also be important to understand the feeding behavior of insect herbivores. Here, we have compared the nutritional characteristics (water content, total protein, free amino acids, total soluble sugars and starch, percent carbon and nitrogen, and macro- and micronutrients) of outer bark and phloem from black, green, white and Manchurian ash to determine their relevance to resistance or susceptibility to EAB. Water content and concentrations of Al, Ba, Cu, Fe, K, Li, tryptophan and an unknown compound were found to separate black and Manchurian ash from green and white ash in a principal component analysis (PCA), confirming their phylogenetic placements into two distinct clades. The traits that distinguished Manchurian ash from black ash in the PCA were water content and concentrations of total soluble sugars, histidine, lysine, methionine, ornithine, proline, sarcosine, tyramine, tyrosol, Al, Fe, K, Na, V and an unknown compound. However, only proline, tyramine and tyrosol were significantly different, and higher, in Manchurian ash than in black ash.

Characterizations of Deposited Ash During Co-Firing of White Pine and Lignite in Fluidized Bed Combustor

NASA Astrophysics Data System (ADS)

Shao, Yuanyuan; Zhu, Jesse; Preto, Fernando; Tourigny, Guy; Wang, Jinsheng; Badour, Chadi; Li, Hanning; Xu, Chunbao Charles

Characterizations of ash deposits from co-firing/co-combusting of a woody biomass (i.e., white pine) and lignite coal were investigated in a fluidized-bed combustor using a custom designed air-cooled probe installed in the freeboard region of the reactor. Ash deposition behaviors on a heat transfer surface were comprehensively investigated and discussed under different conditions including fuel type, fuel blending ratios (20-80% biomass on a thermal basis), and moisture contents. For the combustion of 100% lignite, the compositions of the deposited ash were very similar to those of the fuel ash, while in the combustion of 100% white pine pellets or sawdust the deposited ash contained a much lower contents of CaO, SO3, K2O and P2O5 compared with the fuel ash, but the deposited ash was enriched with SiO2, Al2O3 and MgO. A small addition of white pine (20% on a heat input basis) to the coal led to the highest ash deposition rates likely due to the strong interaction of the CaO and MgO (from the biomass ash) with the alumina and silica (from the lignite ash) during the co-combustion process, evidenced by the detection of high concentrations of calcium/magnesium sulfates, aluminates and silicates in the ash deposits. Interestingly, co-firing of white pine pellets and lignite at a 50% blending ratio led to the lowest ash deposition rates. Ash deposition rates in combustion of fuels as received with a higher moisture content was found to be much lower than those of oven-dried fuels.

Experimental and statistical determination of indicator parameters for the evaluation of fly ash and boiler ash PCDD/PCDF concentration from municipal solid waste incinerators.

PubMed

Streibel, T; Nordsieck, H; Neuer-Etscheidt, K; Schnelle-Kreis, J; Zimmermann, R

2007-04-01

On-line detectable indicator parameters in the flue gas of municipal solid waste incinerators (MSWI) such as chlorinated benzenes (PCBz) are well known surrogate compounds for gas-phase PCDD/PCDF concentration. In the here presented work derivation of indicators is broadened to the detection of fly and boiler ash fractions with increased PCDD/PCDF content. Subsequently these fractions could be subject to further treatment such as recirculation in the combustion chamber to destroy their PCDD/PCDF and other organic pollutants' content. Aim of this work was to detect suitable on-line detectable indicator parameters in the gas phase, which are well correlated to PCDD/PCDF concentration in the solid residues. For this, solid residues and gas-phase samples were taken at three MSWI plants in Bavaria. Analysis of the ash content from different plants yielded a broad variation range of PCDD/PCDF concentrations especially after disturbed combustion conditions. Even during normal operation conditions significantly increased PCDD/PCDF concentrations may occur after unanticipated disturbances. Statistical evaluation of gas phase and ash measurements was carried out by means of principal component analysis, uni- and multivariate correlation analysis. Surprisingly, well known indicators for gas-phase PCDD/PCDF concentration such as polychlorinated benzenes and phenols proved to be insufficiently correlated to PCDD/PCDF content of the solid residues. Moreover, no single parameter alone was found appropriate to describe the PCDD/PCDF content of fly and boiler ashes. On the other hand, multivariate fitting of three or four parameters yielded convenient correlation coefficients of at least r=0.8 for every investigated case. Thereby, comprehension of plant operation parameters such as temperatures and air flow alongside concentrations of inorganic compounds in the gas phase (HCl, CO, SO2, NOx) gave the best results. However, the suitable set of parameters suited best for estimation of PCDD/PCDF concentration in solid residues has to be derived anew for each individual plant and type of ash.

The optimum content of rubber ash in concrete: flexural strength

NASA Astrophysics Data System (ADS)

Senin, M. S.; Shahidan, S.; Shamsuddin, S. M.; Ariffin, S. F. A.; Othman, N. H.; Rahman, R.; Khalid, F. S.; Nazri, F. M.

2017-11-01

Discarded scrap tyres have become one of the major environmental problems nowadays. Several studies have been carried out to reuse waste tires as an additive or sand replacement in concrete with appropriate percentages of tire rubber, called as rubberized concrete to solve this problem. The main objectives of this study are to investigate the flexural strength performance of concrete when adding the rubber ash and also to analyse the optimum content of rubber ash in concrete prisms. The performance total of 30 number of concrete prisms in size of 100mm x 100mm x 500 mm were investigated, by partially replacement of rubber ash with percentage of 0%, 3%, 5%, 7% and 9% from the volume of the sand. The flexural strength is increased when percentage of rubber ash is added 3% from control concrete prism, RA 0 for both concrete prism age, 7 days and 28 days with value 1.21% and 0.976% respectively. However, for RA 5, RA 7 and RA 9, the flexural strength was decreased compared to the control for both age, 7 days and 28 days. In conclusion, 3% is the optimum content of rubber ash in concrete prism for both concrete age

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of flymore » ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature.« less

Experimental study on durability improvement of fly ash concrete with durability improving admixture.

PubMed

Quan, Hong-zhu; Kasami, Hideo

2014-01-01

In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete, the compressive strength of fly ash concrete can be improved by 10%-20%, and the drying shrinkage is reduced by 60%. Carbonation resistance of concrete is roughly proportional to water-cement ratio regardless of water-binder ratio and fly ash replacement ratio. For the specimens cured in air for 2 weeks, the freezing-thawing resistance is improved. In addition, by making use of durability improving admixture, it is easier to control the air content and make fly ash concrete into nonair-entraining one. The quality of fly ash concrete is thereby optimized.

Supply of avocado starch (Persea americana mill) as bioplastic material

NASA Astrophysics Data System (ADS)

Ginting, M. H. S.; Hasibuan, R.; Lubis, M.; Alanjani, F.; Winoto, F. A.; Siregar, R. C.

2018-02-01

The purpose of this study was to determine the effect of time precipitation of avocado slurry seed to yield of starch. Starch analysis included starch content, moisture content, amylose content, amylopectin content, ash content, protein content, fat content, Fourier transform infra red analysis and rapid visco analyzer. Supply of starch from avocado seeds was used by extraction method. Every one hundred grams of avocado slurry was precipitated by gravity with variations for 4 hours, 8 hours, 12 hours, 16 hours, 20 hours and 24 hours. The Starch yield was washed, and dried using oven at 70°C for 30 minutes. Starch yield was the highest as 24.20 gram at 24 hours. The result of starch characterization was 73.62%, water content 16.6%, amylose 0.07%, amylopectin 73.55%, ash content 0.23%, protein content 2.16%, fat content 1.09%. Rapid visco analyzer obtained at 91.33°C of gelatinization temperature. Scanning electron microscopy analyzes obtained 20 μm oval-shaped starch granules. Fourier Transform Infra Red analysis of starch obtained the peak spectrum of O-H group of alcohols, C-H alkanes and C-O ether.

Ash Tree Leaf Litter (Fraxinus excelsior L.) Breakdown in Two Different Biotopes and Streams

NASA Astrophysics Data System (ADS)

Fleituch, Tadeusz; Leichtfried, Maria

2004-11-01

Coarse (0.5 mm) and fine (0.1 mm) mesh size bag methodology was used for comparing the breakdown of ash tree leaves (Fraxinus excelsior L.) in two biotopes (dry - terrestrial and wet - overflown stream zones) in two low order streams (the Oberer Seebach (OSB), Lower Austria and the Brzezowka stream (BRZ), Beskidy Mountains, southern Poland). In total, 96 bags were exposed in autumn 2000. Ash-free dry mass (AFDM) ranged in dry zones of both streams from 94-62% (OSB) and 85-53% (BRZ) respectively. The decomposition process was faster in wet zones: 96-33% (OSB) and 56-11% (B) during the study period. Significant differences in ash breakdown and its chemical content between studied streams were found. Total organic carbon (TOC) and total nitrogen content (TN) of AFDM of litter showed increased differences with experiment duration between zones and between two bag types for both streams. The strongest increase of TOC and TN content (100% on average initial content) for bag types, zones, and streams was observed in the first two weeks of the experiment. These results confirm the importance of chemical compounds for microbiological processes (biofilms) in different ecosystem biotopes. (

Toxic metals distribution in different components of Pakistani and imported cigarettes by electrothermal atomic absorption spectrometer.

PubMed

Kazi, T G; Jalbani, N; Arain, M B; Jamali, M K; Afridi, H I; Sarfraz, R A; Shah, A Q

2009-04-15

It was extensively investigated that a significant flux of toxic metals, along with other toxins, reaches the lungs through smoking. In present study toxic metals (TMs) (Al, Cd, Ni and Pb) were determined in different components of Pakistani local branded and imported cigarettes, including filler tobacco (FT), filter (before and after normal smoking by a single volunteer) and ash by electrothermal atomic absorption spectrometer (ETAAS). Microwave-assisted digestion method was employed. The validity and accuracy of methodology were checked by using certified sample of Virginia tobacco leaves (ICHTJ-cta-VTL-2). The percentages (%) of TMs in different components of cigarette were calculated with respect to their total contents in FT of all branded cigarettes before smoking, while smoke concentration has been calculated by subtracting the filter and ash contents from the filler tobacco content of each branded cigarette. The highest percentage (%) of Al was observed in ash of all cigarettes, with range 97.3-99.0%, while in the case of Cd, a reverse behaviour was observed, as a range of 15.0-31.3% of total contents were left in the ash of all branded cigarettes understudy.

Differential characteristics in the chemical composition of bananas from Tenerife (Canary Islands) and Ecuador.

PubMed

Forster, Markus Paul; Rodríguez Rodríguez, Elena; Díaz Romero, Carlos

2002-12-18

The contents of moisture, protein, ash, ascorbic acid, glucose, fructose, total sugars, and total and insoluble fiber were determined in cultivars of bananas (Gran Enana and Pequeña Enana) harvested in Tenerife and in bananas (Gran Enana) from Ecuador. The chemical compositions in the bananas from Tenerife and from Ecuador were clearly different. The cultivar did not influence the chemical composition, except for insoluble fiber content. Variations of the chemical composition were observed in the bananas from Tenerife according to cultivation method (greenhouse and outdoors), farming style (conventional and organic), and region of production (north and south). A highly significant (r = 0.995) correlation between glucose and fructose was observed. Correlations of ash and protein contents tend to separate the banana samples according to origin. A higher content of protein, ash, and ascorbic acid was observed as the length of the banana decreased. Applying factor analysis, the bananas from Ecuador were well separated from the bananas produced in Tenerife. An almost total differentiation (91.7%) between bananas from Tenerife and bananas from Ecuador was obtained by selecting protein, ash, and ascorbic acid content and applying stepwise discriminant analysis. By selecting the bananas Pequeña Enana and using discriminant analysis, a clear separation of the samples according to the region of production and farming style was observed.

Properties of Controlled Low Strength Material with Circulating Fluidized Bed Combustion Ash and Recycled Aggregates

PubMed Central

Weng, Tsai-Lung; Cheng, An; Chao, Sao-Jeng; Hsu, Hui-Mi

2018-01-01

This study aims to investigate the effect of adding circulating fluidized bed combustion (CFBC) ash, desulfurization slag, air-cooled blast-furnace slag and coal bottom ash to the controlled low-strength material (CLSM). Test methods include slump flow test, ball drop test, water soluble chloride ion content measurement, compressive strength and length change measurement. The results show that (1) the use of CFBC hydration ash with desulfurization slag of slump flow is the best, and the use of CFBC hydration ash with coal bottom ash and slump flow is the worst; (2) CFBC hydration ash with desulfurization slag and chloride ion content is the highest; (3) 24 h ball drop test (diameter ≤ 76 mm), and test results are 70 mm to 76 mm; (4) CFBC hydration ash with desulfurization slag and compression strength is the highest, with the coal bottom ash being the lowest; increase of CFBC hydration ash can reduce compressive strength; and (5) the water-quenched blast furnace slag and CFBC hydration ash would expand, which results in length changes of CLSM specimens. PMID:29724055

Elemental analyses of pine bark and wood in an environmental study.

PubMed

Saarela, K-E; Harju, L; Rajander, J; Lill, J-O; Heselius, S-J; Lindroos, A; Mattsson, K

2005-05-01

Bark and wood samples were taken from the same individuals of Scots pine (Pinus sylvestris L.) from a polluted area close to a Cu-Ni smelter in Harjavalta and from some relatively unpolluted areas in western Finland. The samples were analysed by thick-target particle induced X-ray emission (PIXE) after preconcentration by dry ashing at 550 degrees C. The elemental contents of pine bark and wood were compared to study the impact of heavy metal pollution on pine trees. By comparison of the elemental contents in ashes of bark and wood, a normalisation was obtained. For the relatively clean areas, the ratios of the concentration in bark ash to the concentration in wood ash for different elements were close to 1. This means that the ashes of Scots Pine wood and bark have quite similar elemental composition. For the samples from the polluted area the mean concentration ratios for some heavy metals were elevated (13-28), reflecting the effect of direct atmospheric contamination. The metal contents in the ashes of pine bark and wood were also compared to recommendations for ashes to be recycled back to the forest environment. Bark from areas close to emission sources of heavy metal pollution should be considered with caution if aiming at recycling the ash. Burning of bark fuel of pine grown within 6 km of the Cu-Ni smelter is shown to generate ashes with high levels of Cu, Ni as well as Cd, As and Pb.

Alkali content of fly ash : measuring and testing strategies for compliance.

DOT National Transportation Integrated Search

2015-04-01

Sodium and potassium are the common alkalis present in fly ash. Excessive amounts of fly ash alkalis can cause efflorescence : problems in concrete products and raise concern about the effectiveness of the fly ash to mitigate alkali-silica reaction (...

In-situ biogas upgrading during anaerobic digestion of food waste amended with walnut shell biochar at bench scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linville, Jessica L.; Shen, Yanwen; Ignacio-de Leon, Patricia A.

Here, a modified version of an in-situ CO 2 removal process was applied during AD of food waste with two types of walnut shell biochar (WSB) at bench-scale under batch operating mode. Compared to the coarse WSB, the fine WSB has a higher ash content (43 vs. 36 wt%) and higher concentrations of calcium (31 vs. 19 wt% of ash), magnesium (8.4 vs. 5.6 wt% of ash) and sodium (23.4 vs. 0.3 wt% of ash), but a lower potassium concentration (0.2 vs. 40% wt% of ash). The 0.96 - 3.83 g biochar (g VS added) -1 fine WSB amended digestersmore » produced biogas with 77.5-98.1% CH 4 content by removing 40-96% of the CO 2 compared to the control digesters at mesophilic and thermophilic temperature conditions. In a direct comparison at 1.83 g biochar (g VS added) -1, the fine WSB amended digesters (85.7% CH 4 content and 61% CO 2 removal) outperformed the coarse WSB amended digesters (78.9% CH 4 content and 51% CO 2 removal). Biochar addition also increased alkalinity as CaCO3 from 2,800 mg L -1 in the control digesters to 4,800-6,800 mg L -1 providing process stability for food waste AD.« less

In-situ biogas upgrading during anaerobic digestion of food waste amended with walnut shell biochar at bench scale.

PubMed

Linville, Jessica L; Shen, Yanwen; Ignacio-de Leon, Patricia A; Schoene, Robin P; Urgun-Demirtas, Meltem

2017-06-01

A modified version of an in-situ CO 2 removal process was applied during anaerobic digestion of food waste with two types of walnut shell biochar at bench scale under batch operating mode. Compared with the coarse walnut shell biochar, the fine walnut shell biochar has a higher ash content (43 vs. 36 wt%) and higher concentrations of calcium (31 vs. 19 wt% of ash), magnesium (8.4 vs. 5.6 wt% of ash) and sodium (23.4 vs. 0.3 wt% of ash), but a lower potassium concentration (0.2 vs. 40% wt% of ash). The 0.96-3.83 g biochar (g VS added ) -1 fine walnut shell biochar amended digesters produced biogas with 77.5%-98.1% CH 4 content by removing 40%-96% of the CO 2 compared with the control digesters at mesophilic and thermophilic temperature conditions. In a direct comparison at 1.83 g biochar (g VS added ) -1 , the fine walnut shell biochar amended digesters (85.7% CH 4 content and 61% CO 2 removal) outperformed the coarse walnut shell biochar amended digesters (78.9% CH 4 content and 51% CO 2 removal). Biochar addition also increased alkalinity as CaCO 3 from 2800 mg L -1 in the control digesters to 4800-6800 mg L -1 , providing process stability for food waste anaerobic digestion.

In-situ biogas upgrading during anaerobic digestion of food waste amended with walnut shell biochar at bench scale

DOE PAGES

Linville, Jessica L.; Shen, Yanwen; Ignacio-de Leon, Patricia A.; ...

2017-05-10

Here, a modified version of an in-situ CO 2 removal process was applied during AD of food waste with two types of walnut shell biochar (WSB) at bench-scale under batch operating mode. Compared to the coarse WSB, the fine WSB has a higher ash content (43 vs. 36 wt%) and higher concentrations of calcium (31 vs. 19 wt% of ash), magnesium (8.4 vs. 5.6 wt% of ash) and sodium (23.4 vs. 0.3 wt% of ash), but a lower potassium concentration (0.2 vs. 40% wt% of ash). The 0.96 - 3.83 g biochar (g VS added) -1 fine WSB amended digestersmore » produced biogas with 77.5-98.1% CH 4 content by removing 40-96% of the CO 2 compared to the control digesters at mesophilic and thermophilic temperature conditions. In a direct comparison at 1.83 g biochar (g VS added) -1, the fine WSB amended digesters (85.7% CH 4 content and 61% CO 2 removal) outperformed the coarse WSB amended digesters (78.9% CH 4 content and 51% CO 2 removal). Biochar addition also increased alkalinity as CaCO3 from 2,800 mg L -1 in the control digesters to 4,800-6,800 mg L -1 providing process stability for food waste AD.« less

Chemical composition, mineral content and amino acid and lipid profiles in bones from various fish species.

PubMed

Toppe, Jogeir; Albrektsen, Sissel; Hope, Britt; Aksnes, Anders

2007-03-01

The chemical composition, content of minerals and the profiles of amino acids and fatty acids were analyzed in fish bones from eight different species of fish. Fish bones varied significantly in chemical composition. The main difference was lipid content ranging from 23 g/kg in cod (Gadus morhua) to 509 g/kg in mackerel (Scomber scombrus). In general fatty fish species showed higher lipid levels in the bones compared to lean fish species. Similarly, lower levels of protein and ash were observed in bones from fatty fish species. Protein levels differed from 363 g/kg lipid free dry matter (dm) to 568 g/kg lipid free dm with a concomitant inverse difference in ash content. Ash to protein ratio differed from 0.78 to 1.71 with the lowest level in fish that naturally have highest swimming and physical activity. Saithe (Pollachius virens) and salmon (Salmo salar) were found to be significantly different in the levels of lipid, protein and ash, and ash/protein ratio in the bones. Only small differences were observed in the level of amino acids although species specific differences were observed. The levels of Ca and P in lipid free fish bones were about the same in all species analyzed. Fatty acid profile differed in relation to total lipid levels in the fish bones, but some minor differences between fish species were observed.

Effect of chitosan coatings enriched with cinnamon oil on proximate composition of rainbow trout fillets

NASA Astrophysics Data System (ADS)

Yıldız, Pınar Oǧuzhan

2017-04-01

The effects of chitosan coating enriched with cinnamon oil on proximate composition of rainbow trout (Oncorhynchus mykiss) during storage at 4°C was investigated. The treatments included the following: C1 (control samples), C2 (chitosan coating) and C3 (chitosan + 1 % [v/w] cinnamon EO added). The control and the coated fish samples were analysed for chemical (moisture, protein, lipid and ash) composition. The mean of moisture, protein, lipid and ash in the control samples (C1) were 70.3%, 20.1%, 2.6% and 1.2%, in coated samples (C2) 69.70%, 24.21%, 2.4% and 2.2% and coated+cinnamon oil samples (C3) 69.70%, 25.05%, 2.5% and 2.2%, respectively. Moisture and lipid contents in control groups were higher than other groups, but protein and ash contents were lower. Significant increases (p<0.05) in protein content were observed between samples, which subsequently decreased the moisture content of these samples.

The influence of HCl concentration and demineralization temperature of Atrina pectinata shells on quality of chitin

NASA Astrophysics Data System (ADS)

Nugroho, Intan Lazuardi; Pursetyo, Kustiawan Tri; Masithah, Endang Dewi

2017-02-01

Atrina pectinata is one of shells species widely consumed by people, which means the high consumption will generate the availability of shells in the environment as waste. Chitin can be produced from the shells. Shells contain quite high minerals that it should be demineralized to reduce the mineral content from the shells. This study aimed to determine the effect of HCl concentration and temperature affect chitin characteristics as the result of demineralization process from pen shells. The method based on two steps, there were demineralization and deproteination. This study used Completely Randomized Design (CRD) with two factors, including HCl concentration (2N, 4N, and 6N) and temperature (33°C and 60°C) which consists six combination treatments and three replications. Data was analyzed by using Analysis of Variance (ANOVA) and followed by Duncan's Multiple Range Test. The results showed that interaction of HCl concentration and temperature has significant effect (p<0.05) to ash content of chitin. The use concentration of 6N and 33°C produced the lowest ash content. Characteristics chitin resulted from the treatment of 6N and 33°C produced ash content 25.33% ± 6.82, moisture content 3.67% ± 1.10, yield 0.72% ± 0.12 and protein content 5.86%.

Utilization of western coal fly ash in construction of highways in the Midwest

DOT National Transportation Integrated Search

2000-03-01

Coal burning utilities in the Midwest are increasingly using sub-bituminous coal from Wyoming. These utilities typically produce fly ash, which, because of its high calcium oxide content, may be classified as Class C fly ash. These ashes are characte...

Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

PubMed

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

2017-06-01

In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Effect of the harvest season on the composition of raw and fermented cotyledons of 2 varieties of cacao and shell fractions].

PubMed

de Dios Alvarado, J; Villacís, F E; Zamora, G F

1983-06-01

A study was carried out wherein during the period August 1979 to January 1980, samples of raw and fermented cacao were analyzed monthly. These included two varieties: Arriba, taken from a farm in "Quevedo", and the EET-19, grown in "Pichilingüe" by the Instituto Nacional de Investigaciones Agropecuarias (INIAP). Taking the ear of cacao as a basis, the weight of its main parts was determined. The proximal composition was established in the cotyledons, with significant statistical differences in regard to moisture, protein, and ether extract content according to the month of harvest. As to the fermentation process, differences in moisture, ether extract and ash content were detected; differences in the ether extract and ash content were found between the two varieties. The fat extracted from the cotyledons presented different iodine, saponification and acidity index values between the raw and fermented samples, but none were determined between the varieties; as far as the month of harvest is concerned, differences in the acidity index were observed. The percentage composition of the main fatty acids is reported (palmitic, stearic, oleic, and linoleic acids). In order to suggest possible industrial ways of utilizing the cacao shell by-product which is discarded by the shelling machine, the chemical characteristics of five fractions were determined based on the functioning of the shelling machine. The moisture, protein, ether extract, ash, crude fiber, theobromine, and caffeine contents varied among the fractions, and it was dependent on the broken "nibs" content. Differences in the protein, ether extract, and ash content, according to the months of production, were found. Obviously, the high fat content in fractions A (fine dust) and B (fine ground), which varied from 30 to 11 g/100 g, merits its extraction; the remainder meal has a valuable protein and alkaloid content. The chemical characteristics of the fat extracted from the shell of two fractions were similar to the fat extracted from the cotyledons.

The effect of habitat geology on calcium intake and calcium status of wild rodents.

PubMed

Shore, R F; Balment, R J; Yalden, D W

1991-12-01

Calcium is essential for normal physiological function, reproduction and growth in mammals but its distribution in the natural environment is heterogeneous. Spatial variation in calcium soil content is especially marked in the Peak District, United Kingdom, where both calcium-rich limestone and calcium-poor gritstone rock types occur. Wood mice Apodemus sylvaticus (L) and bank voles Clethrionomys glareolus (Schreber 1780) from limestone areas had significantly higher calcium concentrations in stomach contents and in faeces compared with their counterparts from gritstone areas. Calcium status was assessed from serum calcium concentration, femur weight, ash content of the body, calcium concentration in the femur and body ash. There was no significant difference in serum calcium concentration, femur calcium concentration and body ash calcium concentration between animals from the limestone and the gritstone. However, on the limestone, bank voles, but not wood mice, had significantly heavier femora and a greater proportion of ash in the body compared with their gritstone counterparts.

Synthesis of geopolymer composites from a mixture of ferronickel slag and fly ash

NASA Astrophysics Data System (ADS)

Liu, Yun; Zhang, Kang; Feng, Enjuan; Zhao, Hongyi; Liu, Futian

2017-03-01

The synthesis of geopolymers using ferronickel slag and fly ash under alkaline activation was studied. In order to study the effects of different fly ash content on the mechanical properties of the geopolymers produced, the compressive strength of samples was tested at 3, 7, 28 days. The results showed that when the fly ash content was 40%, the compressive strength reached the highest (110.32MPa) at 28 days. XRD analysis showed that the ferronickel slag geopolymers had amorphous aluminosilicate phase formation, indicating that the hydration reaction occurred. FTIR analysis showed the reaction of the geopolymers generated at Si-O-T (Si, Al) and Al-O-Si three-dimensional network. In SEM images, the structure of the geopolymers with 40% fly ash was more compact and cohesive.

[Analysis of commercial grades of Schisandrae Sphenantherae Fructus based on schisantherin].

PubMed

Wang, Zhen-Heng; Jin, Ling; Ma, Yi; Cui, Zhi-Jia; Li, Qian; Huang, De-Dong

2017-10-01

Schisandrae Sphenantherae Fructus, from different producing areas, were collected and divided into three grades. The moisture content and total ash were determined on the basis of the pharmacopoeia method, and schisantherin was determined by UPLC. The study is aimed to find the commercial specifications and grades of Schisandrae Sphenantherae Fructus based on schisantherin content. The results showed that the content of water, total ash and schisantherin of Schisandrae Sphenantherae Fructus from different producing areas qualified. There was no significant difference between different grades of schisandrin content, but the second-class were the highest, first-class and third-class were lower. It means that schisandrin content is not positive correlation to commercial grade. The study will be helpful to the production, management and clinical practice of Schisandrae Sphenantherae Fructus. Copyright© by the Chinese Pharmaceutical Association.

Gypsum treated fly ash as a liner for waste disposal facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivapullaiah, Puvvadi V., E-mail: siva@civil.iisc.ernet.in; Baig, M. Arif Ali, E-mail: reach2arif@gmail.com

2011-02-15

Fly ash has potential application in the construction of base liners for waste containment facilities. While most of the fly ashes improve in the strength with curing, the ranges of permeabilities they attain may often not meet the basic requirement of a liner material. An attempt has been made in the present context to reduce the hydraulic conductivity by adding lime content up to 10% to two selected samples of class F fly ashes. The use of gypsum, which is known to accelerate the unconfined compressive strength by increasing the lime reactivity, has been investigated in further improving the hydraulicmore » conductivity. Hydraulic conductivities of the compacted specimens have been determined in the laboratory using the falling head method. It has been observed that the addition of gypsum reduces the hydraulic conductivity of the lime treated fly ashes. The reduction in the hydraulic conductivity of the samples containing gypsum is significantly more for samples with high amounts of lime contents (as high as 1000 times) than those fly ashes with lower amounts of lime. However there is a relatively more increase in the strengths of the samples with the inclusion of gypsum to the fly ashes at lower lime contents. This is due to the fact that excess lime added to fly ash is not effectively converted into pozzolanic compounds. Even the presence of gypsum is observed not to activate these reactions with excess lime. On the other hand the higher amount of lime in the presence of sulphate is observed to produce more cementitious compounds which block the pores in the fly ash. The consequent reduction in the hydraulic conductivity of fly ash would be beneficial in reducing the leachability of trace elements present in the fly ash when used as a base liner.« less

Physical, chemical and sensory properties of brownies substituted with sweet potato flour (Ipomoea batatas L.) with addition of black cumin oil (Nigella sativa L.)

NASA Astrophysics Data System (ADS)

Ligarnasari, I. P.; Anam, C.; Sanjaya, A. P.

2018-01-01

Effect of addition black cumin oil on the physical (hardness) characteristics, chemical (water, ash, fat, protein, carbohydrate, antioxidant IC50, total phenol and active component) characteristics and sensory (flavor, taste, texture, overall) characteristics of brownies substituted sweet potato flour were investigated. Substituted brownies was added with 0.05%, 0.10%, 0.15%, 0.20% and 0.25% of nigella sativa oil. The result showed that water content, ash, protein, fat, total phenol were increased and carbohydrate, antioxidant IC50 was decreased by the addition of nigella sativa oil. Due to the sensory characteristics, panelist gave the high score for substituted brownies which was added 0.05% nigella sativa oil. The result showed that the best formula of substituted brownies which was added 0.05% of nigella sativa oil had 24.89% water content, 1.19% ash content, 7.54% protein content, 37.79% fat content, 53.06% carbohydrate contain, 1043.6 ppm IC50 antioxidant and 0.22% total phenol. The active component on the brownies using GCMS identification were palmitic acid, oleic acid, lauric acid, theobromine and vitamin E.

Evaluation of coalbed gas potential of the Seelyville Coal Member, Indiana, USA

USGS Publications Warehouse

Drobniak, A.; Mastalerz, Maria; Rupp, J.; Eaton, N.

2004-01-01

The Seelyville Coal Member of the Linton Formation in Indiana potentially contains 0.03 trillion m3 (1.1 TCF) of coalbed gas. The gas content determined by canister desorption technique ranges from 0.5 to 5.7 cm3/g on dry ash free basis (15.4 to 182.2 scf/ton). The controls on gas content distribution are complex, and cannot be explained by the coal rank alone. Ash content and the lithology of the overlying strata, among other factors, may influence this distribution. ?? 2004 Elsevier B.V. All rights reserved.

Mercury in coals and fly ashes from Republika and Bobov dol thermoelectric power plants

USGS Publications Warehouse

Kostova, I.; Vassileva, C.; Hower, J.; Mastalerz, Maria; Vassilev, S.; Nikolova, N.

2011-01-01

Feed coal and y ash samples were collected at Republika and Bobov Dol thermoelectric power plants (TPPs). The y ashes (FAs) were collected fromthree rows of the hot-side electrostatic precipitators (ESPs) array. Each sam- ple was wet-screened at 100, 200, 325 and 500 mesh. The coals and y ashes were characterized with regard to their petrological and chemical composition (including mercury content) and to their surface area properties. The calculated enrichment factor (EF) shows that the Hg concentrations in the bulk coal samples from Republika and Bobov Dol TPPs are 2.19 and 1.41, respectively. In some coal size fractions the EF can be up to 4 times higher than the Clarke value. The calculated EF for fly ashes shows that the Hg concentrations in the bulk samples studied are lower (between 0.03 and 0.32) than the Clarke value. The most enriched in Hg are the fly ashes from the 3rd ESP row of Republika TPP. The Hg distribution in bulk FAs taken from dierent rows of the electrostatic precipitators of both TPPs studied shows well established tendency of gradual increase in the Hg content from the 1st to the 2nd and 3rd ESP rows. The correlation between Hg content and surface area, mesopore and micropore volume of y ashes was also done in the present investigation.

Quantifying the Impact of Feedstock Quality on the Design of Bioenergy Supply Chain Networks

DOE PAGES

Castillo-Villar, Krystel; Minor-Popocatl, Hertwin; Webb, Erin

2016-03-01

Logging residues, which refer to the unused portions of trees cut during logging, are important sources of biomass for the emerging biofuel industry and are critical feedstocks for the first-type biofuel facilities (e.g., corn-ethanol facilities). Logging residues are under-utilized sources of biomass for energetic purposes. To support the scaling-up of the bioenergy industry, it is essential to design cost-effective biofuel supply chains that not only minimize costs, but also consider the biomass quality characteristics. The biomass quality is heavily dependent upon the moisture and the ash contents. Ignoring the biomass quality characteristics and its intrinsic costs may yield substantial economicmore » losses that will only be discovered after operations at a biorefinery have begun. Here this paper proposes a novel bioenergy supply chain network design model that minimizes operational costs and includes the biomass quality-related costs. The proposed model is unique in the sense that it supports decisions where quality is not unrealistically assumed to be perfect. The effectiveness of the proposed methodology is proven by assessing a case study in the state of Tennessee, USA. The results demonstrate that the ash and moisture contents of logging residues affect the performance of the supply chain (in monetary terms). Higher-than-target moisture and ash contents incur in additional quality-related costs. The quality-related costs in the optimal solution (with final ash content of 1% and final moisture of 50%) account for 27% of overall supply chain cost. In conclusion, based on the numeral experimentation, the total supply chain cost increased 7%, on average, for each additional percent in the final ash content.« less

Quantifying the Impact of Feedstock Quality on the Design of Bioenergy Supply Chain Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castillo-Villar, Krystel; Minor-Popocatl, Hertwin; Webb, Erin

Logging residues, which refer to the unused portions of trees cut during logging, are important sources of biomass for the emerging biofuel industry and are critical feedstocks for the first-type biofuel facilities (e.g., corn-ethanol facilities). Logging residues are under-utilized sources of biomass for energetic purposes. To support the scaling-up of the bioenergy industry, it is essential to design cost-effective biofuel supply chains that not only minimize costs, but also consider the biomass quality characteristics. The biomass quality is heavily dependent upon the moisture and the ash contents. Ignoring the biomass quality characteristics and its intrinsic costs may yield substantial economicmore » losses that will only be discovered after operations at a biorefinery have begun. Here this paper proposes a novel bioenergy supply chain network design model that minimizes operational costs and includes the biomass quality-related costs. The proposed model is unique in the sense that it supports decisions where quality is not unrealistically assumed to be perfect. The effectiveness of the proposed methodology is proven by assessing a case study in the state of Tennessee, USA. The results demonstrate that the ash and moisture contents of logging residues affect the performance of the supply chain (in monetary terms). Higher-than-target moisture and ash contents incur in additional quality-related costs. The quality-related costs in the optimal solution (with final ash content of 1% and final moisture of 50%) account for 27% of overall supply chain cost. In conclusion, based on the numeral experimentation, the total supply chain cost increased 7%, on average, for each additional percent in the final ash content.« less

Radiological and material characterization of high volume fly ash concrete.

PubMed

Ignjatović, I; Sas, Z; Dragaš, J; Somlai, J; Kovács, T

2017-03-01

The main goal of research presented in this paper was the material and radiological characterization of high volume fly ash concrete (HVFAC) in terms of determination of natural radionuclide content and radon emanation and exhalation coefficients. All concrete samples were made with a fly ash content between 50% and 70% of the total amount of cementitious materials from one coal burning power plant in Serbia. Physical (fresh and hardened concrete density) and mechanical properties (compressive strength, splitting tensile strength and modulus of elasticity) of concrete were tested. The radionuclide content ( 226 Ra, 232 Th and 40 K) and radon massic exhalation of HVFAC samples were determined using gamma spectrometry. Determination of massic exhalation rates of HVFAC and its components using radon accumulation chamber techniques combined with a radon monitor was performed. The results show a beneficial effect of pozzolanic activity since the increase in fly ash content resulted in an increase in compressive strength of HVFAC by approximately 20% for the same mass of cement used in the mixtures. On the basis of the obtained radionuclide content of concrete components the I -indices of different HVFAC samples were calculated and compared with measured values (0.27-0.32), which were significantly below the recommended 1.0 index value. The prediction was relatively close to the measured values as the ratio between the calculated and measured I-index ranged between 0.89 and 1.14. Collected results of mechanical and radiological properties and performed calculations clearly prove that all 10 designed concretes with a certain type of fly ash are suitable for structural and non-structural applications both from a material and radiological point of view. Copyright © 2016 Elsevier Ltd. All rights reserved.

Deashing macroalgae biomass by pulsed electric field treatment.

PubMed

Robin, Arthur; Sack, Martin; Israel, Alvaro; Frey, Wolfgang; Müller, Georg; Golberg, Alexander

2018-05-01

Among all biomass constituents, the ashes are major hurdles for biomass processing. Ashes currently have low market value and can make a non-negligible fraction of the biomass dry weight significantly impacting its further processing by degrading equipment, lowering process yield, inhibiting reactions and decreasing products qualities. However, most of the current treatments for deashing biomass are of poor efficiency or industrial relevance. This work is the first report on the use of Pulsed Electric Field (PEF) to enhance deashing of biomass from a high ash content green marine macroalga, Ulva sp., using hydraulic pressing. By inducing cell permeabilization of the fresh biomass, PEF was able to enhance the ash extraction from 18.4% (non-treated control) to 37.4% of the total ash content in average, significantly enhancing the extraction of five of the major ash elements (K, Mg, Na, P and S) compared to pressing alone. Copyright © 2018 Elsevier Ltd. All rights reserved.

Geotechnical characterization of some Indian fly ashes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, S.K.; Yudhbir

2005-10-01

This paper reports the findings of experimental studies with regard to some common engineering properties (e.g., grain size, specific gravity, compaction characteristics, and unconfined compression strength) of both low and high calcium fly ashes, to evaluate their suitability as embankment materials and reclamation fills. In addition, morphology, chemistry, and mineralogy of fly ashes are studied using scanning electron microscope, electron dispersive x-ray analyzer, x-ray diffractometer, and infrared absorption spectroscopy. In high calcium fly ash, mineralogical and chemical differences are observed for particles, {gt}75 {mu} m and the particles of {lt} 45 {mu} m size. The mode and duration of curingmore » significantly affect the strength and stress-strain behavior of fly ashes. The geotechnical properties of fly ash are governed by factors like lime content (CaO), iron content (Fe{sub 2}O{sub 3}) and loss on ignition. The distinct difference between self-hardening and pozzolanic reactivity has been emphasized.« less

The durability of concrete containing a high-level of fly ash or a ternary blend of supplementary cementing materials

NASA Astrophysics Data System (ADS)

Gilbert, Christine M.

The research for this study was conducted in two distinct phases as follows: Phase 1: The objective was to determine the effect of fly ash on the carbonation of concrete. The specimens made for this phase of the study were larger in size than those normally used in carbonation studies and were are meant to more accurately reflect real field conditions. The results from early age carbonation testing indicate that the larger size specimens do not have a measured depth of carbonation as great as that of the smaller specimens typically used in carbonation studies at the same age and under the same conditions. Phase 2: The objective was to evaluate the performance of ternary concrete mixes containing a ternary cement blend consisting of Portland cement, slag and Type C fly ash. It was found that concrete mixtures containing the fly ash with the lower calcium (CaO) content (in binary or ternary blends) provided superior durability performance and resistance to ASR compared to that of the fly ash with the higher CaO content. Ternary blends (regardless of the CaO content of the fly ash) provided better overall durability performance than binary blends of cementing materials or the control.

Characterization and modes of occurrence of elements in feed coal and fly ash; an integrated approach

USGS Publications Warehouse

Brownfield, M.E.

2002-01-01

Despite certain environmental concerns, coal is likely to remain an important component of the United States energy supply, partly because it is the most abundant domestically available fossil fuel. One of the concerns about coal combustion for electricity production is the potential release of elements from coal and coal combustion products (CCPs) - fly ash - to the environment. This concern prompted the need for accurate, reliable, and comprehensive information on the contents and modes of occurrence of selected elements in power-plant feed coal and fly ash. The U.S. Geological Survey (USGS) is collaborating with several electric utilities to determine the chemical and mineralogical properties of feed coal and fly ash. Our first study analyzed coal and fly ash from a Kentucky power plant, which uses many different bituminous coals from the Appalachian and Illinois Basins. Sulfur content of these feed coals rangedfrom 2.5 to 3.5 percent. The second study analyzed coal and fly ash from an Indiana power plant, which uses subbituminous coal from the Powder River Basin (fig. 1). Sulfur content of this feed coal ranged from 0.23 to 0.47 percent. A summary of important aspects of our approach and results are presented in this report. 

JV Task 107- Pilot-Scale Emission Control Technology Testing for Constellation Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael Jones; Brandon Pavlish; Stephen Sollom

2007-06-30

An Indonesian, Colombian, and Russian coal were tested in the Energy & Environmental Research Center's combustion test facility for their performance and an evaluation of mercury release and capture with selected additives in both electrostatic precipitator and baghouse configurations. Sorbents included the carbon-based materials NORIT DARCO Hg, Sorbent Technologies B-PAC and B-PAC LC, STI Rejects provided by Constellation Energy, and Envergex e-Sorb, along with ChemMod's high-temperature additive. Each coal was evaluated over several days and compared. Ash-fouling tests were conducted, and mercury levels were monitored using continuous mercury monitors (CMMs). The Ontario Hydro mercury sampling method was also utilized. Themore » Indonesian coal had the lowest ash content, lowest sulfur content, and lowest energy content of the three coals tested. The Colombian coal had the highest mercury content and did contain a significant level of selenium which can interfere with the ability of a CMM to monitor mercury in the gas stream. All sorbents displayed very favorable results. In most cases, mercury removal greater than 86% could be obtained. The Indonesian coal displayed the best mercury removal with sorbent addition. A maximum removal of 97% was measured with this coal using Envergex's carbon-based sorbent at a rate of 4 lb/Macf across an electrostatic precipitator. The high ash and selenium content of the Colombian coal caused it to be a problematic fuel, and ash plugging of the test furnace was a real concern. Problems with the baghouse module led to limited testing. Results indicated that native capture across the baghouse for each coal type was significant enough not to warrant sorbent addition necessary. The fouling potential was the lowest for the Indonesian coal. Low sulfur content contributes to the poor potential for fouling, as witnessed by the lack of deposits during testing. The Russian and Colombian coals had a much higher potential for fouling primarily because of their high ash contents, but the potential was highest for the Colombian coal. Of the three coals tested, the Colombian would be the least desirable.« less

Removal of chloride from MSWI fly ash.

PubMed

Chen, Wei-Sheng; Chang, Fang-Chih; Shen, Yun-Hwei; Tsai, Min-Shing; Ko, Chun-Han

2012-10-30

The high levels of alkali chloride and soluble metal salts present in MSWI fly ash is worth noting for their impact on the environment. In addition, the recycling or reuse of fly ash has become an issue because of limited landfill space. The chloride content in fly ash limits its application as basis for construction materials. Water-soluble chlorides such as potassium chloride (KCl), sodium chloride (NaCl), and calcium chloride hydrate (CaCl(2) · 2H(2)O) in fly ash are easily washed away. However, calcium chloride hydroxide (Ca(OH)Cl) might not be easy to leach away at room temperature. The roasting and washing-flushing processes were applied to remove chloride content in this study. Additionally, air and CO(2) were introduced into the washing process to neutralize the hazardous nature of chlorides. In comparison with the water flushing process, the roasting process is more efficient in reducing the process of solid-liquid separation and drying for the reuse of Cl-removed fly ash particles. In several roasting experiments, the removal of chloride content from fly ash at 1050°C for 3h showed the best results (83% chloride removal efficiency). At a solid to liquid ratio of 1:10 the water-flushing process can almost totally remove water-soluble chloride (97% chloride removal efficiency). Analyses of mineralogical change also prove the efficiency of the fly ash roasting and washing mechanisms for chloride removal. Copyright © 2012 Elsevier B.V. All rights reserved.

Mechanism of unintentionally produced persistent organic pollutant formation in iron ore sintering.

PubMed

Sun, Yifei; Liu, Lina; Fu, Xin; Zhu, Tianle; Buekens, Alfons; Yang, Xiaoyi; Wang, Qiang

2016-04-05

Effects of temperature, carbon content and copper additive on formation of chlorobenzenes (CBzs) and polychlorinated biphenyls (PCBs) in iron ore sintering were investigated. By heating simulated fly ash (SFA) at a temperature range of 250-500°C, the yield of both CBzs and PCBs presented two peaks of 637ng/g-fly ash at 350°C and 1.5×10(5)ng/g-fly ash at 450°C for CBzs, and 74ng/g-fly ash at 300°C and 53ng/g-fly ash at 500°C. Additionally, in the thermal treatment of real fly ash (RFA), yield of PCBs displayed two peak values at 350°C and 500°C, however, yield of CBzs showed only one peak at 400°C. In the thermal treatment of SFA with a carbon content range of 0-20wt% at 300°C, both CBzs and PCBs obtained the maximum productions of 883ng/g-fly ash for CBzs and 127ng/g-fly ash for PCBs at a 5wt% carbon content. Copper additives also affected chlorinated aromatic formation. The catalytic activity of different copper additives followed the orders: CuCl2∙2H2O>Cu2O>Cu>CuSO4>CuO for CBzs, and CuCl2∙2H2O>Cu2O>CuO>Cu>CuSO4 for PCBs. Copyright © 2015 Elsevier B.V. All rights reserved.

Selenium content and oxidation states in fly ashes from western U.S. coals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V; Quinn, Thomas R

2003-08-01

A selective extraction scheme was developed for the determination of the oxidation states of Se species in coal ashes. As compared to HF dissolution, extractions with 70% HC1O4 mobilized 90 to 100% of all compound and redox forms of Se from four of the five fly ashes. Extractions with 16M HNO3 did not mobilize all forms of Se as effectively as perchloric acid. Both oxidized forms of Se (IV and VI) were completely mobilized by 12M HCl extraction. Deionized-distilled water was not an effective extractant for mobilizing all compound forms of Se(IV) from fly ashes. Extraction data (70% HClO4, 16Mmore » HNO3, 12M HCl, DI water) indicated that the solid:solution ratio is a critical factor in Se extractability from fly ashes. Maximum extractions in all cases were obtained only with very high (1:500) solid:solution ratios. Extraction times from 1.5 to 25 hours did not significantly change Se extractability with any of the extractants except with 12M HCl, which required a minimum reaction time of 48 hours to attain maximum Se extractability. Reaction times shorter than the critical time and low solid:solution ratios significantly affected Se extractability from these fly ashes. Measurements of Se content and redox state in particle size and density fractions five western United States coal ashes indicated that typically, the Se content increased with decreasing particle size.. However, no consistent trend in Se concentration between the light and heavy density fractions of <2.7-m size fraction was observed. Selenium redox state data indicated that only Se(0) and Se(IV) forms were present in these five coal ashes. The presence of Se(IV) is significant since it is much more easily mobilized than the elemental form. Examination of fly ashes by the proposed scheme to determine Se redox species could permit better estimation of the Se content of plants grown on fly ash amended soils.« less

Experimental Study on Durability Improvement of Fly Ash Concrete with Durability Improving Admixture

PubMed Central

Quan, Hong-zhu; Kasami, Hideo

2014-01-01

In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete, the compressive strength of fly ash concrete can be improved by 10%–20%, and the drying shrinkage is reduced by 60%. Carbonation resistance of concrete is roughly proportional to water-cement ratio regardless of water-binder ratio and fly ash replacement ratio. For the specimens cured in air for 2 weeks, the freezing-thawing resistance is improved. In addition, by making use of durability improving admixture, it is easier to control the air content and make fly ash concrete into nonair-entraining one. The quality of fly ash concrete is thereby optimized. PMID:25013870

Effect of water content on the water repellency for hydrophobized sands

NASA Astrophysics Data System (ADS)

Subedi, S.; Kawamoto, K.; Kuroda, T.; Moldrup, P.; Komatsu, T.

2011-12-01

Alternative earthen covers such as capillary barriers (CBs) and evapotranspirative covers are recognized as useful technical and low-cost solutions for limiting water infiltration and controlling seepage flow at solid waste landfills in semi-arid and arid regions. However, their application to the landfills at wet regions seems to be matter of concern due to loss of their impending capability under high precipitation. One of the possible techniques to enhance the impermeable properties of CBs is to alter soil grain surfaces to be water-repellent by mixing/coating hydrophobic agents (HAs). In order to examine a potential use of model sands hydrophobized with locally available and environmental-friendly HAs such as oleic acid (OA) and stearic acid (SA) for hydrophobic CBs. In the present study, we first characterized the effect of water content on the degree of water repellency (WR) for hydrophobized sands and volcanic ash soil at different depth. Secondly, the time dependency of the contact angle in hydrophobized sands and volcanic ash soils at different water content was evaluated. Further, the effects of hydrophobic organic matter contents on the WR of hydrophobized sands were investigated by horizontal infiltration test. We investigated the degree of WR as functions of volumetric water content (θ) of a volcanic ash soil samples from different depth and water adjusted hydrophobized sand samples with different ratio of HAs by using sessile drop method (SDM). The initial contact angle (αi) measured from SDM decreased gradually with increasing water content in OA and SA coated samples. Measured αi values for volcanic ash soils increased with increasing water content and reached a peak values of 111.7o at θ= 0.325 cm3 cm-3, where-after αi gradually decreased. Each test sample exhibited sharp decrease in contact angle with time at higher water content. Sorptivity values for oleic acid coated samples decreased with increasing HA content and reached the minimum value of 0.068 cm s-1/2 at 1 g HA kg-1 sand, and then gradually increased.

Spectroscopic studies of fly ash-based geopolymers

NASA Astrophysics Data System (ADS)

Rożek, Piotr; Król, Magdalena; Mozgawa, Włodzimierz

2018-06-01

In the present work fly-ash based geopolymers with different contents of alkali-activator and water were prepared. Alkali-activation was conducted with sodium hydroxide (NaOH) at the SiO2/Na2O molar ratio of 3, 4, and 5. Water content was at the ratio of 30, 40, and 50 wt% in respect to the weight of the fly ash. Structural and microstructural characterization (FT-IR spectroscopy, 29Si and 27Al MAS NMR, X-ray diffraction, SEM) of the specimens as well as compressive strength and apparent density measurements were carried out. The obtained geopolymers are mainly amorphous due to the presence of disordered aluminosilicate phases. However, hydroxysodalite have been identified as a crystalline product of geopolymerization. The major band in the mid-infrared spectra (at about 1000 cm-1) is related to Sisbnd O(Si,Al) asymmetric stretching vibrations and is an indicator of the geopolymeric network formation. Several component bands in this region can be noticed after the decomposition process. Decomposition of band at 1450 cm-1 (vibrations of Csbnd O bonds in bicarbonate group) has been also conducted. Higher NaOH content favors carbonation, inasmuch as the intensity of the band then increases. Both water and alkaline activator contents have an influence on compressive strength and microstructure of the obtained fly-ash based geopolymers.

Influence of Cements Containing Calcareous Fly Ash as a Main Component Properties of Fresh Cement Mixtures

NASA Astrophysics Data System (ADS)

Gołaszewski, Jacek; Kostrzanowska-Siedlarz, Aleksandra; Ponikiewski, Tomasz; Miera, Patrycja

2017-10-01

The main goal of presented research was to examine usability of cements containing calcareous fly ash (W) from technological point of view. In the paper the results of tests concerning the influence of CEM II and CEM IV cements containing fly ash (W) on rheological properties, air content, setting times and plastic shrinkage of mortars are presented and discussed. Moreover, compatibility of plasticizers with cements containing fly ash (W) was also studied. Additionally, setting time and hydration heat of cements containing calcareous fly ash (W) were determined. In a broader aspect, the research contributes to promulgation of the possibility of using calcareous fly ash (W) in cement and concrete technology, what greatly benefits the environment protection (utilization of waste fly ash). Calcareous fly ash can be used successfully as the main component of cement. Cements produced by blending with processed fly ash or cements produced by interginding are characterized by acceptable technological properties. In respect to CEM I cements, cements containing calcareous fly ash worsen workability, decrease air content, delay setting time of mixtures. Cements with calcareous fly ash show good compatibility with plasticizers.

Study of morphology, chemical, and amino acid composition of red deer meat.

PubMed

Okuskhanova, Eleonora; Assenova, Bahytkul; Rebezov, Maksim; Amirkhanov, Kumarbek; Yessimbekov, Zhanibek; Smolnikova, Farida; Nurgazezova, Almagul; Nurymkhan, Gulnur; Stuart, Marilyne

2017-06-01

The aim of this study was to evaluate red deer (maral) meat quality based on chemical composition, pH, water-binding capacity (WBC), and amino acid content. Maral meat surface morphology measurements were obtained by scanning electron microscopy. Active acidity (pH) was determined by potentiometry. Samples were analyzed for WBC by exudation of moisture to a filter paper by the application of pressure. Chemical composition (moisture, protein, fat, and ash fractions) was obtained by drying at 150°C and by extraction, using ethylic ether, and ashing at 500-600°C. The amino acid composition was obtained by liquid chromatography. Maral meat, with a pH of 5.85 and an average moisture content of 76.82%, was found to be low in fat (2.26%). Its protein content was 18.71% while its ash content was 2.21%. The amino acid composition showed that lysine (9.85 g/100 g), threonine (5.38 g/100 g), and valine (5.84 g/100 g) predominated in maral meat, while phenylalanine (4.08 g/100 g), methionine (3.29 g/100 g), and tryptophan (0.94 g/100 g) were relatively low in maral meat compared to other meats. The average WBC was found to be 65.82% and WBC was found to inversely correlate with moisture content. Low-fat content, high mineral content, and balanced amino-acid composition qualify maral meat as a worthy dietary and functional food.

Study of morphology, chemical, and amino acid composition of red deer meat

PubMed Central

Okuskhanova, Eleonora; Assenova, Bahytkul; Rebezov, Maksim; Amirkhanov, Kumarbek; Yessimbekov, Zhanibek; Smolnikova, Farida; Nurgazezova, Almagul; Nurymkhan, Gulnur; Stuart, Marilyne

2017-01-01

Aim: The aim of this study was to evaluate red deer (maral) meat quality based on chemical composition, pH, water-binding capacity (WBC), and amino acid content. Materials and Methods: Maral meat surface morphology measurements were obtained by scanning electron microscopy. Active acidity (pH) was determined by potentiometry. Samples were analyzed for WBC by exudation of moisture to a filter paper by the application of pressure. Chemical composition (moisture, protein, fat, and ash fractions) was obtained by drying at 150°C and by extraction, using ethylic ether, and ashing at 500-600°C. The amino acid composition was obtained by liquid chromatography. Results: Maral meat, with a pH of 5.85 and an average moisture content of 76.82%, was found to be low in fat (2.26%). Its protein content was 18.71% while its ash content was 2.21%. The amino acid composition showed that lysine (9.85 g/100 g), threonine (5.38 g/100 g), and valine (5.84 g/100 g) predominated in maral meat, while phenylalanine (4.08 g/100 g), methionine (3.29 g/100 g), and tryptophan (0.94 g/100 g) were relatively low in maral meat compared to other meats. The average WBC was found to be 65.82% and WBC was found to inversely correlate with moisture content. Conclusion: Low-fat content, high mineral content, and balanced amino-acid composition qualify maral meat as a worthy dietary and functional food. PMID:28717313

Selenium in fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutenmann, W.H.; Bache, C.A.; Youngs, W.D.

1976-03-05

Selenium, at concentrations exceeding 200 parts per million (ppM) (dry weight), has been found in white sweet clover voluntarily growing on beds of fly ash in central New York State. Guinea pigs fed such clover concentrated selenium in their tissues. The contents of the honey stomachs of bees foraging on this seleniferous clover contained negligible selenium. Mature vegetables cultured on 10 percent (by weight) fly ash-amended soil absorbed up to 1 ppM of selenium. Fly ashes from 21 states contained total selenium contents ranging from 1.2 to 16.5 ppM. Cabbage grown on soil containing 10 percent (by weight) of thesemore » fly ashes absorbed selenium (up to 3.7 ppM) in direct proportion (correlation coefficient r = .89) to the selenium concentration in the respective fly ash. Water, aquatic weeds, algae, dragonfly nymphs, polliwogs, and tissues of bullheads and muskrats from a fly ash-contaminated pond contained concentrations of selenium markedly elevated over those of controls.« less

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

PubMed

Saqib, Naeem; Bäckström, Mattias

2014-12-01

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

Leachate concentrations from water leach and column leach tests on fly ash-stabilized soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bin-Shafique, S.; Benson, C.H.; Edil, T.B.

2006-01-15

Batch water leaching tests (WLTs) and column leaching tests (CLTs) were conducted on coal-combustion fly ashes, soil, and soil-fly ash mixtures to characterize leaching of Cd, Cr, Se, and Ag. The concentrations of these metals were also measured in the field at two sites where soft fine-grained soils were mechanically stabilized with fly ash. Concentrations in leachate from the WLTs on soil-fly ash mixtures are different from those on fly ash alone and cannot be accurately estimated based on linear dilution calculations using concentrations from WLTs on fly ash alone. The concentration varies nonlinearly with fly ash content due tomore » the variation in pH with fly ash content. Leachate concentrations are low when the pH of the leachate or the cation exchange capacity (CEC) of the soil is high. Initial concentrations from CLTs are higher than concentrations from WLTs due to differences in solid-liquid ratio, pH, and solid-liquid contact. However, both exhibit similar trends with fly ash content, leachate pH, and soil properties. Scaling factors can be applied to WLT concentrations (50 for Ag and Cd, 10 for Cr and Se) to estimate initial concentrations for CLTs. Concentrations in leachate collected from the field sites were generally similar or slightly lower than concentrations measured in CLTs on the same materials. Thus, CLTs appear to provide a good indication of conditions that occur in the field provided that the test conditions mimic the field conditions. In addition, initial concentrations in the field can be conservatively estimated from WLT concentrations using the aforementioned scaling factors provided that the pH of the infiltrating water is near neutral.« less

Hemp (Cannabis sativa L.) as an Environmentally Friendly Energyplant

NASA Astrophysics Data System (ADS)

Poisa, Liena; Adamovics, Aleksandrs

2010-01-01

Hemp is suitable as a renewable energy resource. The aim of this study was to clarify local hemp's (Cannabis sativa L.) possibilities for energy use. Arsenic (As), cadmium (Cd), lead (Pb) and titanium (Ti) presence in hemp was determined using an inductively coupled plasma optical emission spectrometer Optima 2100 DV. If there were increased N fertilizer rates, there were increased hemp `Pūriņi' seeds and shive yield increases, but the oil content was reduced. Arsenic content was higher in the shives than in the stems with fibre. The ash content depends on non-organic substances which the plants absorb during the vegetation season. The lignin content depends on several factors: plant parts, and the N fertilizer rate. The unexplored factors have a great effect on the ash and lignin content. Hemp is suitable for cultivation and for bio-energy production in the agro-climatic conditions in Latvia.

Potential of solid waste utilization as source of refuse derived fuel (RDF) energy (case study at temporary solid waste disposal site in West Jakarta)

NASA Astrophysics Data System (ADS)

Indrawati, D.; Lindu, M.; Denita, P.

2018-01-01

This study aims to measure the volume of solid waste generated as well asits density, composition, and characteristics, to analyze the potential of waste in TPS to become RDF materials and to analyze the best composition mixture of RDF materials. The results show that the average of solid waste generation in TPS reaches 40.80 m3/day, with the largest percentage of its share is the organic waste component of 77.9%, while the smallest amount of its share is metal and rubber of 0.1%. The average water content and ash content of solid waste at the TPS is 27.7% and 6.4% respectively, while the average calorific potential value is 728.71 kcal/kg. The results of solid waste characteristics comparison at three TPS indicate thatTPS Tanjung Duren has the greatest waste potential to be processed into RDF materials with a calorific value of 893.73 kcal/kg, water content level of 24.6%, andlow ash content of 6.11%. This research has also shown that the best composition for RDF composite materials is rubber, wood, and textile mixtureexposed to outdoor drying conditions because it produced low water content and low ash content of 10.8% and 9.6%, thus optimizedthe calorific value of 4,372.896 kcal/kg.

Basic characteristics of leachate produced by various washing processes for MSWI ashes in Taiwan.

PubMed

Yang, Renbo; Liao, Wing-Ping; Wu, Pin-Han

2012-08-15

Approximately 19.2% of Taiwan's municipal solid waste (MSW) that passes through incineration disposal is converted into ashes (including bottom ash and fly ash). Although bottom ash can pass nearly all of the standards of the toxicity characteristic leaching procedure (TCLP), its high chloride content makes its reuse limited; it generally cannot be used as a fine aggregate material in concrete applications. This research examined washing four types of bottom ash (BA) and fly ash (FA) with water to reduce their chloride content. The optimal water intensity for washing pretreated bottom ash was found to be 7-8L of water per kg of bottom ash, and the optimal water intensity for washing untreated fly ash was found to be 20-25 L of water per kg of fly ash. Based on regression analyses of the chloride concentrations of the leachates and their electrical conductivity (EC) values, each MSW incineration plant has its own ash characteristics as well as a specific regression line in bottom or fly ash leachate. Clearly, it is possible to monitor the EC values of the leachates online by estimation from regression equations to determine the chloride concentrations in the leachates. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Optimization of an organic yogurt based on sensorial, nutritional, and functional perspectives.

PubMed

Karnopp, Ariadne Roberto; Oliveira, Katherine Guimarães; de Andrade, Eriel Forville; Postingher, Bruna Mara; Granato, Daniel

2017-10-15

The effects of purple grape juice (PGJ), grape skin flour (GSF), and oligofructose (OLI) on proximate composition, total phenolic content (TPC), antioxidant activity (AA), sensory, physicochemical, and textural properties of yogurts were analyzed using response surface methodology. Multiple regression models were proposed and results showed that PGJ increased the viscosity, AA, and TPC, while GSF increased the ash and total fiber contents of yogurts. GSF and OLI increased the hardness and consistency. A simultaneous optimization was performed to maximize TPC, ash and fibers contents, and sensory acceptance: a yogurt containing 1.7% GSF and 8.0% PGJ had a high fiber (5.60±0.13%) and ash (0.76±0.02%) contents, TPC (28.32±2.10mg GAE/100g), AA toward DPPH (57.85±1.36mg AAE/100g), and total reducing capacity (28.86±5.19mg QE/100g). The optimized yogurt had 79% acceptability index, indicating the use of PGJ and GSF is a feasible alternative to increase the functional properties of yogurts. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Influence of shenxu gutong capsule on femoral inorganic elements content and ash weight in rats].

PubMed

Chen, X; Wei, J; Chen, Y

1998-02-01

To explore the mechanism of Shenxu Gutong Capsule (SXGTC) in treating postmenopausal osteoporosis. Using ovariectomized rats as the model of postmenopausal osteoporosis, the effect of SXGTC on inorganic element content of femur and femoral ash weight of the model rats were surveyed. Animals were divided into model group, SXGTC high dose group, SXGTC low dose group, positive control group (treated with Gushukang) and normal control group. The medication began at one week after operation and lasting for 120 days. The contents of inorganic elements, including Ca, P, Mg, Zn, Cu and Mn in the three medicated groups were higher than those of the model group (P < 0.01). The effect of SXGTC was dose dependent. The difference between the SXGTC groups and the positive control group was insignificant. The femoral ash weight of the SXGTC high dose group and the positive control group was significantly higher than that of the model group (P < 0.01). SXGTC could antagonize the rat's bony change caused by ovariectomy to increase the inorganic contents in bone, which may, in grneral, lead to a bone-strengthening effect.

Stability and broad-sense heritaibility of mineral content in potato: copper and sulfur

USDA-ARS?s Scientific Manuscript database

Potato breeding lines and varieties in two separate trials were evaluated for copper and sulfur content by wet ashing and Inductively Coupled Argon Plasma Emission Spectrophotometer analysis. Stability and broad-sense heritability were determined. Copper contents ranged among genotypes between 2.0...

Mineral content of the honey produced in Zulia state, Venezuela.

PubMed

Sulbarán de Ferrer, Betzabé; Ojeda de Rodríguez, Graciela; Peña, Jorge; Martínez, Janeth; Morán, María

2004-09-01

The mineral content of the honey produced in five zones of the Zulia state, Venezuela, during dry and rainy seasons was determined. The analyzed elements were: sodium, potassium (by emission spectroscopy), calcium, magnesium, copper, iron, manganese (by atomic absorption spectroscopy), phosphorus (phosphate ions, by colorimetric method), and ash content of raw honey samples directly collected from different beekeepers. The mean values for Na, K, Ca, Mg, Cu, Fe, Mn, and P were 353+84; 1774+138; 237+66; 52+24; 0.76+0.43; 13.5+10.23; 0.92+0.42 and 1642+323 mg/kg respectively. The mean ash content was 0.431+0.15%. Potassium was the most abundant of the elements determined. This results confirm that Zulian honey can be considered a good source of minerals.

The development of a new method to detect the adulteration of commercial aloe gel powders.

PubMed

Kim, K H; Lee, J G; Kim, D G; Kim, M K; Park, J H; Shin, Y G; Lee, S K; Jo, T H; Oh, S T

1998-10-01

Simple and accurate methods to detect the adulteration of commercial aloe gel powder were developed. Crude polysaccharide in aloe gel powder was isolated by precipitating with excess ethyl alcohol and total hexose in isolated polysaccharide was determined by Dubois assay. After hydrolysis of non-dialysable polysaccharides, resultant free sugar was determined by gas chromatography for sugar recognition and ash contents was considered simultaneously. In some products, the content of ash was very low while the content of total hexose was very high. And polysaccharides of these products revealed typical dextran pattern, therefore, these products could be identified that adulterated with commercial maltodextrin. The content of maltodextrin in adulterated product was determined by HPLC and TLC analysis which could be adopted as a part of a certification process.

Heavy metals and PCDD/Fs in solid waste incinerator fly ash in Zhejiang province, China: chemical and bio-analytical characterization.

PubMed

Yao, Jun; Li, Wenbing; Xia, Fangfang; Zheng, Yuange; Fang, Chengran; Shen, Dongsheng

2012-06-01

Fly ash samples were taken from solid waste incinerators with different feeding waste, furnace type, and air pollution control device in six cities of Zhejiang province. The solid waste incinerators there constitute one fifth of incinerators in China. Heavy metals and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were analyzed in the fly ash. Moreover, the fly ash samples were extracted by toxicity characteristic leaching procedure (TCLP). The biotoxicity of the leachate was evaluated by Chlorella pyrenoidosa. High variation and contents were found for both the heavy metals and PCDD/Fs. The contents of Zn, Cu, As, Pb, Cd, Cr, Ni, and Hg in the fly ash samples varied from 300 to 32,100, 62.1-1175, 1.1-57, 61.6-620, 0.4-223, 16.6-4380, 1.2-94.7, and 0.03-1.4 μg g(-1) dw, respectively. The total contents of 17 PCDD/Fs varied from 0.1128 to 127.7939 μg g(-1) dw, and the 2,3,7,8-TeCDD toxic equivalents (TEQ) of PCDD/Fs ranged from 0.009 to 6.177 μg g(-1) dw. PCDF congeners were the main contributor to the TEQ. The leachate of the fly ash showed biotoxicity to C. pyrenoidosa. A significant correlation was found between the Cd and EC(50) values. Further research is required to investigate the environmental impact of the various pollutants in the fly ash.

Removal of chloride from fly ash produced in hazardous waste incineration by leaching and displacement washing in a vertical filter press.

PubMed

Kinnarinen, Teemu; Huhtanen, Mikko; Penttilä, Mika; Häkkinen, Antti

2013-02-01

Fly ash is generated in large quantities by waste incineration processes. Chloride is commonly present in the fly ash produced by the incineration of hazardous materials, such as polyvinylchloride plastic. Major difficulties related to the disposal and handling of fly ash include the high concentration of easily leachable chlorides, heavy metals and toxic compounds. In order to avoid adverse environmental effects from the disposal of fly ash, the content of soluble chlorides must be reduced. One of the most effective options for chloride removal is leaching and displacement washing in a filter press. The primary aim of this study was to obtain efficient removal of chloride from fly ash by utilizing a leaching and displacement washing process, carried out in a filter press. The secondary objective was to obtain high filtration capacities and low filter cake moisture contents. The slurry was prepared by mixing fly ash with water at an ash:water ratio of 1:2 and filtered to separate the solids from the liquid. After solid-liquid separation, most of the dissolved residual chloride was removed from the filter cake by washing the cake with fresh water in the second stage of separation. It was possible to remove up to 98% of the total chloride and to obtain sufficient filtration capacities. The residual moisture content of the filter cakes varied from 22 to 35 wt%, which meant that the cakes could be disposed of in landfill, or possibly utilized as a construction material.

Relationship between textural properties, fly ash carbons, and Hg capture in fly ashes derived from the combustion of anthracitic pulverized feed blends

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isabel Surez-Ruiz; Jose B. Parra

2007-08-15

In this work, the textural properties of a series of whole anthracitic-derived fly ashes sampled in eight hoppers from the electrostatic precipitators and their sized fractions (from {gt}150 to {lt}25 {mu}m) are investigated. Data from N{sub 2} adsorption isotherms at 77 K, helium density, and mercury porosimetry have contributed to establish a relationship between the Brunauer-Emmett-Teller (BET) surface areas, VTOT, porosity, carbon content (the type of fly ash carbons), and Hg retention in these fly ashes. The unburned carbons in these ashes are macroporous materials, and they are different from the carbons in fly ashes from classes C and Fmore » (the latter derived from the combustion of bituminous coals) and show different textural properties. These ashes represent the end member of the fly ash classes C and F with respect to certain textural properties. Although the BET surface area and VTOT values for the studied samples are the lowest reported, they increase with the increase in carbon content, anisotropic carbon content, and particle size of the ashes. Thus, a positive relationship between all these parameters and Hg capture by the coarser ash fractions was found. The finest fraction of carbons ({lt}25 {mu}m) represented an exception. Although it makes a significant contribution to the total carbon of the whole fly ashes and shows relatively higher surface areas and VTOT values, its Hg concentration was found to be the lowest. This suggests that the type of unburned carbons in the finest fraction and/or other adsorption mechanisms may play a role in Hg concentration. Because the textural properties of anisotropic carbons depend on their subtype and on their origin, the need for its differentiation has been evidenced. 54 refs., 8 figs., 3 tabs.« less

Radioactivity of coals and ash and slag wastes at coal-fired thermal power plants

NASA Astrophysics Data System (ADS)

Krylov, D. A.; Sidorova, G. P.

2013-04-01

This paper presents an analysis of published data on the content of radioactive nuclides in coals originating from various coal deposits, and in ash and slag wastes produced at coal-fired thermal power plants, as well as in fly ash emitted from thermal power plants into the atmosphere. Problems related to the use of coals with an elevated content of natural radionuclides (NRNs) and methods of their solution implemented at the Urtuyskoe coalfield are dealt with. Data on the analysis of Transbaikal coals for the NRN content, as well as weighted mean content of uranium and thorium in coals from the Siberian Region, are given. In order to reduce irradiation of plant personnel and the population of the areas where coal producers and coal-fired thermal power plants are located, it is necessary to organize very careful control of the NRN content in both coals and products of their combustion that are released into the environment. To solve the problem related to the control of radioactivity, the centralized approach and creation of a proper normative base are needed. Experience gained in developing the Urtuyskoe coalfield shows that it is possible to create an efficient system of coal quality control with respect to the radiation hygiene factor and provide protection of the environment and health of the population.

40 CFR 98.68 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.../metric tons Al) Individual facility records. Sa: sulfur content in baked anode (percent weight) 2.0. Asha: ash content in baked anode (percent weight) 0.4. CO2 Emissions from Sderberg Cells (VSS and HSS) MP... content in green anodes (metric tons) 0.005 × GA. BA: annual baked anode production (metric tons...

Soil quality in a cropland soil treated with wood ash containing charcoal

NASA Astrophysics Data System (ADS)

Omil, Beatriz; Balboa, Miguel A.; Fonturbel, M. Teresa; Gartzia-Bengoetxea, Nahia; Arias-González, Ander; Vega, Jose A.; Merino, Agustin

2014-05-01

The strategy of the European Union "Europe 2020" states that by 2020, 20% of final energy consumption must come from renewables. In this scenario, there is an increasing use of biomass utilization for energy production. Indeed, it is expected that the production of wood-ash will increase in coming years. Wood ash, a mixture of ash and charcoal, generated as a by-product of biomass combustion in power plants, can be applied to soil to improve the soil quality and crop production. Since the residue contains significant content of charcoal, the application of mixed wood ash may also improve the SOM content and soil quality in the long term, in soils degraded as a consequence of intensive management. The objective of this study was asses the changes in SOM quality and soil properties in a degraded soils treated with wood ash containing charcoal. The study was carried out in a field devoted to cereal crops during the last decades. The soil was acidic (pH 4.5) with a low SOC content (3 %) and fine texture. The experiment was based on a randomised block design with four replicates. Each block included the following four treatments: Control, 16 Mg fly wood ash ha-1, 16 Mg mixed wood ash ha-1 (16 Mg) and 32 Mg mixed wood ash ha-1 (32 Mg). The application was carried out once. The ash used in the study was obtained from a thermal power plant and was mainly derived from the combustion of Pinus radiata bark and branches. The wood ash is highly alkaline (pH= 10), contains 10 % of highly condensed black carbon (atomic H/C ratio < 0.5 and T50 en DSC= 500 ºC). The evolution of SOM properties were monitored over three years by solid state 13C CPMAS NMR and Differential Scanning Calorimetry (DSC). These techniques were applied in bulk samples and aggregates of different sizes. The changes in microbial activity were studied by analysis of microbial biomass C and basal respiration. The soil bacterial community was studied by the Biolog method. Several physical properties, such soil aggregate distribution, hydraulic conductivity and available water contente were also determined. Three years after applications the SOM content increased lightly in the treatment receiving more than 16 Mg ha-1 of wood ash. SOM in the treated soils displayed a higher degree of aromaticity than in the untreated soils, indicating a gain in more stable SOM compounds probably as a consequence of the charcoal application. However, both methods also revealed increases in labile C compounds, probably due to the carbohydrates added through root system. Microbial biomass-C and soil respiration increased significantly. The treatments also led to increases in the functional diversity indices. The amended soils showed greater utilization of substrates and the ability of soil bacteria to utilize different C resources was also greatly altered. The application of mixed wood ash did not lead to any difference in MWD, which was around 6 mm in all cases. The application of 16 Mg fly wood ash ha-1 increased significantly the hydraulic conductivity (4.07 cmh-1) when compared with in control plots (1.3 cmh-1) and mixed ash plots (1.52 and 2.45 cmh-1, 16 Mg and 32 Mg respectively). However, air-filled porosity was not higher in 16 Mg fly ash plots. AWC was not improved by wood ash application.

From in-situ coal to fly ash: A study of coal mines and power plants from Indiana

USGS Publications Warehouse

Mastalerz, Maria; Hower, J.C.; Drobniak, A.; Mardon, S.M.; Lis, G.

2004-01-01

This paper presents data on the properties of coal and fly ash from two coal mines and two power plants that burn single-source coal from two mines in Indiana. One mine is in the low-sulfur (5%) Springfield Coal Member of the Petersburg Formation (Pennsylvanian). Both seams have comparable ash contents (???11%). Coals sampled at the mines (both raw and washed fractions) were analyzed for proximate/ultimate/sulfur forms/heating value, major oxides, trace elements and petrographic composition. The properties of fly ash from these coals reflect the properties of the feed coal, as well as local combustion and post-combustion conditions. Sulfur and spinel content, and As, Pb and Zn concentrations of the fly ash are the parameters that most closely reflect the properties of the source coal. ?? 2004 Elsevier B.V. All rights reserved.

Development of a standard operating procedure for analysis of ammonia concentrations in coal fly ash.

DOT National Transportation Integrated Search

2015-04-01

Research was performed to support the development and recommendation of a standard operating : procedure (SOP) for analyzing the ammonia content in fly ash intended for use in concrete. A review : of existing ash producers found that several differen...

Leaching characteristics of fly ash from thermal power plants of Soma and Tuncbilek, Turkey.

PubMed

Baba, Alper; Kaya, Abidin

2004-02-01

Use of lignite in power generation has led to increasing environmental problems associated not only with gaseous emissions but also with the disposal of ash residues. In particular, use of low quality coal with high ash content results in huge quantities of fly ash to be disposed of. The main problem related to fly ash disposal is the heavy metal content of the residue. In this regard, experimental results of numerous studies indicate that toxic trace metals may leach when fly ash contacts water. In this study, fly ash samples obtained from thermal power plants, namely Soma and Tunçbilek, located at the west part of Turkey, were subjected to toxicity tests such as European Committee for standardization (CEN) and toxicity characteristic leaching (TCLP) procedures of the U.S. Environmental Protection Agency (U.S. EPA). The geochemical composition of the tested ash samples from the power plant show variations depending on the coal burned in the plants. Furthermore, the CEN and TCLP extraction results showed variations such that the ash samples were classified as 'toxic waste' based on TCLP result whereas they were classified as 'non-toxic' wastes based on CEN results, indicating test results are pH dependent.

Characterization of ash melting behaviour at high temperatures under conditions simulating combustible solid waste gasification.

PubMed

Niu, Miaomiao; Dong, Qing; Huang, Yaji; Jin, Baosheng; Wang, Hongyan; Gu, Haiming

2018-05-01

To achieve high-temperature gasification-melting of combustible solid waste, ash melting behaviour under conditions simulating high-temperature gasification were studied. Raw ash (RA) and gasified ash (GA) were prepared respectively by waste ashing and fluidized bed gasification. Results of microstructure and composition of the two-ash indicated that GA showed a more porous structure and higher content of alkali and alkali earth metals among metallic elements. Higher temperature promoted GA melting and could reach a complete flowing state at about 1250°C. The order of melting rate of GA under different atmospheres was reducing condition > inert condition > oxidizing condition, which might be related to different existing forms of iron during melting and different flux content with atmosphere. Compared to RA, GA showed lower melting activity at the same condition due to the existence of an unconverted carbon and hollow structure. The melting temperature for sufficient melting and separation of GA should be at least 1250°C in this work.

Speciation of Cr and its leachability in coal by-products from spanish coal combustion plants.

PubMed

López-Antón, M Antonia; Díaz-Somoano, Mercedes; Cuesta, Aida Fuente; Riesco, Aida Rubio; Martínez-Tarazona, M Rosa

2008-06-01

This study evaluates the behaviour of total Cr and Cr (VI) during coal combustion in two Spanish power stations. The content and distribution of Cr in the feed coal and combustion wastes was determined and the Cr contents were normalized using enrichment factor indexes. The speciation of Cr in the fly ash fractions from the different hoppers of the electrostatic precipitators was established and the possibility that the Cr (VI) might lixiviate when ashes are disposed of at landfill sites was assessed. Differences in the distribution and behavior of Cr in the two power stations were observed. According to European directive 1999/31/CEE, soluble Cr(VI) in the fly ashes studied would be unlikely to pose an environmental or health risk when the ash is disposed of.

Characterization of ash in algae and other materials by determination of wet acid indigestible ash and microscopic examination

USDA-ARS?s Scientific Manuscript database

Algae are known for high ash content. It is important to properly characterize their ash for value added utilization of algae as food, feed, and feedstock for biofuels. In this study, 12 algae of different sources were measured for proximate composition and mineral profile. Results showed that the r...

Study of Polyolefines Waste Thermo-Destruction in Large Laboratory and in Industrial Installations

DTIC Science & Technology

2014-12-15

coke ”–waste after thermo-destruction carried out on the module No 2 showed an content to 46.1% of ash [20]. This ash content indicates a very large... coke (post-production waste) from the wastes thermo-destruction on 2 modules of vertical modular installation for thermo-destruction of used polymer...of receivedwaste water, the quantity of received coke , the quantity of gaseous product in periods of carrying out installation work before (first

Genetic parameters for body weight, carcass chemical composition and yield in a broiler-layer cross developed for QTL mapping

PubMed Central

Nunes, Beatriz do Nascimento; Ramos, Salvador Boccaletti; Savegnago, Rodrigo Pelicioni; Ledur, Mônica Corrêa; Nones, Kátia; Klein, Claudete Hara; Munari, Danísio Prado

2011-01-01

The objective of this study was to estimate genetic and phenotypic correlations of body weight at 6 weeks of age (BW6), as well as final carcass yield, and moisture, protein, fat and ash contents, using data from 3,422 F2 chickens originated from reciprocal cross between a broiler and a layer line. Variance components were estimated by the REML method, using animal models for evaluating random additive genetic and fixed contemporary group (sex, hatch and genetic group) effects. The heritability estimates (h2) for BW6, carcass yield and percentage of carcass moisture were 0.31 ± 0.07, 0.20 ± 0.05 and 0.33 ± 0.07, respectively. The h2 for the percentages of protein, fat and ash on a dry matter basis were 0.48 ± 0.09, 0.55 ± 0.10 and 0.36 ± 0.08, respectively. BW6 had a positive genetic correlation with fat percentage in the carcass, but a negative one with protein and ash contents. Carcass yield, thus, appears to have only low genetic association with carcass composition traits. The genetic correlations observed between traits, measured on a dry matter basis, indicated that selection for carcass protein content may favor higher ash content and a lower percentage of carcass fat. PMID:21931515

Comparison of leaching characteristics of heavy metals from bottom and fly ashes in Korea and Japan.

PubMed

Shim, Young-Sook; Rhee, Seung-Whee; Lee, Woo-Keun

2005-01-01

The objective of this research was to compare the leaching characteristics of heavy metals such as cadmium, chromium, copper, nickel, lead, etc., in Korean and Japanese municipal solid waste incineration (MSWI) ash. The rate of leaching of heavy metal was measured by KSLT and JTL-13, and the amount of heavy metals leached was compared with the metal content in each waste component. Finally, bio-availability testing was performed to assess the risks associated with heavy metals leached from bottom ash and fly ash. From the results, the value of neutralization ability in Japanese fly ash was four times higher than that in Korean fly ash. The reason was the difference in the content of Ca(OH)(2) in fly ash. The amount of lead leached exceeded the regulatory level in both Japanese and Korean fly ash. The rate of leaching was relatively low in ash with a pH in the range of 6-10. The bio-availability test in fly ash demonstrated that the amount of heavy metals leached was Pb>Cd>Cr, but the order was changed to Pb>Cr>Cd in the bottom ash. The leaching concentration of lead exceeded the Japanese risk level in all fly ashes from the two countries, but the leaching concentration of cadmium exceeded the regulatory level in Korean fly ash only.

Quality and generation rate of solid residues in the boiler of a waste-to-energy plant.

PubMed

Allegrini, E; Boldrin, A; Jansson, S; Lundtorp, K; Fruergaard Astrup, T

2014-04-15

The Danish waste management system relies significantly on waste-to-energy (WtE) plants. The ash produced at the energy recovery section (boiler ash) is classified as hazardous waste, and is commonly mixed with fly ash and air pollution control residues before disposal. In this study, a detailed characterization of boiler ash from a Danish grate-based mass burn type WtE was performed, to evaluate the potential for improving ash management. Samples were collected at 10 different points along the boiler's convective part, and analysed for grain size distribution, content of inorganic elements, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD and PCDF), and leaching of metals. For all samples, PCDD and PCDF levels were below regulatory limits, while high pH values and leaching of e.g. Cl were critical. No significant differences were found between boiler ash from individual sections of the boiler, in terms of total content and leaching, indicating that separate management of individual ash fractions may not provide significant benefits. Copyright © 2014 Elsevier B.V. All rights reserved.

Elemental characterization of Mt. Sinabung volcanic ash, Indonesia by Neutron Activation Analysis

NASA Astrophysics Data System (ADS)

Kusmartini, I.; Syahfitri, W. Y. N.; Kurniawati, S.; Lestiani, D. D.; Santoso, M.

2017-06-01

Mount Sinabung is a volcano located in North Sumatera, Indonesia which has been recorded not erupted since 1600. However in 2013 it has been erupted and cause of black thick smog, rain sand and volcanic ash. Volcanic ash containing trace elements material that can be utilized in various applications but still has potential danger of heavy metals. In order to obtain an elemental composition data of volcanic ash, the characterization of volcanic ash were carried out using Neutron Activation Analysis. The volcanic ash was taken from Mt. Sinabung eruption. Samples were irradiated at the rabbit system in the reactor G.A Siwabessy facilities with neutron flux ˜ 1013 n.cm-2.s-1 and then counted using HPGe detector. Method validation was carried out by SRM NIST Coal Fly Ash 1633b and NIST 2711a Montana II Soil with recovery values were in the range of 96-108% and 95-106% respectively. The results showed that major elements; Al, Na, Ca and Fe, concentrations were 8.7, 1.05, 2.98 and 7.44 %, respectively, minor elements K, Mg, Mn, Ti, V and Zn were 0.87%, 0.78%, 0.18%, 0.62%, 197.13 ppm and 109.35 ppm, respectively, heavy metals; As, Cr, Co and Sb, contents were 4.48, 11.75, 17.13 and 0.35 ppm, respectively while rare earth elements such as Ce, Eu, La, Nd, Sm, Yb were 45.33, 1.22, 19.63, 20.34, 3.86, and 2.57 ppm respectively. The results of the elemental contents of volcanic ash that has been obtained can be used as the scientific based data for volcanic material utilization by considering the economic potential of elements contained and also the danger of the heavy metals content.

The analysis of mechanical properties of non autoclaved aerated concrete with the substitution of fly ash and bottom ash

NASA Astrophysics Data System (ADS)

Karolina, R.; Muhammad, F.

2018-02-01

Based on PP. No.85 of 1999 on the management of hazardous and toxic (B3), fly ash and bottom ash wastes are categorized into B3 waste because there are heavy metal oxide contents that can pollute the environment. One form of environmental rescue that can be applied is to utilize waste fly ash and bottom ash in the manufacture of concrete. In this research, fly ash and bottom ash waste are used as substitution of cement and fine aggregate to make lightweight concrete. The purpose of this research is to know the mechanical properties of non-autoclaved aerated lightweight concrete (NAAC) with FA and BA substitution to cement and fine aggregate which is expected to improve the quality of concrete. The NAAC lightweight concrete in this study is divided into 4 categories: normal NAAC lightweight concrete, NAAC lightweight NAAC substituted concrete with FA, NAAC lightweight concrete substituted with BA, and NAAC combined light weight from FA and BA with variations of 10%, 20% And 30%. The test specimen used in cylindrical shape, which was tested at the age of 28 days, amounted to 90 pieces and consisted of 10 variations. Each variation amounted to 9 samples. Based on the test results with FA and BA substitutions of 10%, 20%, and 30%, the highest compressive strength was achieved in samples with FA 30% of 12.687 MPa, maximum tensile strength achieved in samples with FA 30% of 1,540 MPa, The highest absorption was achieved in normal NAAC of 5.66%. Based on the weight of the contents of all samples, samples can be categorized in lightweight concrete, since the weight of the contents is less than 1900 kg / m3.

Restoration of fly ash dump through biological interventions.

PubMed

Juwarkar, Asha A; Jambhulkar, Hemlata P

2008-04-01

Field experiment on 10 ha area of fly ash dump was conducted to restore and revegetate it using biological interventions, which involves use of organic amendment, selection of suitable plant species along with specialized nitrogen fixing strains of biofertilizer. The results of the study indicated that amendment with farm yard manure at 50 t/ha improved the physical properties of fly ash such as maximum water holding capacity from 40.0 to 62.42% while porosity improved from 56.78 to 58.45%. The nitrogen content was increased by 4.5 times due to addition of nitrogen fixing strains of Bradyrhizobium and Azotobacter species, while phosphate content was increased by 10.0 times due to addition of VAM, which helps in phosphate immobilization. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in fly ash improved to 7.1 x 10(7), 9.2 x 10(7) CFU/g and 35 VAM spores/10 g of fly ash, respectively. Inoculation of biofertilizer and application of FYM helped in reducing the toxicity of heavy metals such as cadmium, copper, nickel and lead which were reduced by 25, 46, 48 and 47%, respectively, due to the increased organic matter content in the fly ash which complexes the heavy metals thereby decreasing the toxicity of metals. Amendment of fly ash with FYM and biofertilizer helped in profuse root development showing 15 times higher growth in Dendrocalamus strictus plant as compared to the control. Thus amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant.

Low temperature circulating fluidized bed gasification and co-gasification of municipal sewage sludge. Part 2: Evaluation of ash materials as phosphorus fertilizer.

PubMed

Thomsen, Tobias Pape; Hauggaard-Nielsen, Henrik; Gøbel, Benny; Stoholm, Peder; Ahrenfeldt, Jesper; Henriksen, Ulrik B; Müller-Stöver, Dorette Sophie

2017-08-01

The study is part 2 of 2 in an investigation of gasification and co-gasification of municipal sewage sludge in low temperature gasifiers. In this work, solid residuals from thermal gasification and co-gasification of municipal sewage sludge were investigated for their potential use as fertilizer. Ashes from five different low temperature circulating fluidized bed (LT-CFB) gasification campaigns including two mono-sludge campaigns, two sludge/straw mixed fuels campaigns and a straw reference campaign were compared. Experiments were conducted on two different LT-CFBs with thermal capacities of 100kW and 6MW, respectively. The assessment included: (i) Elemental composition and recovery of key elements and heavy metals; (ii) content of total carbon (C) and total nitrogen (N); (iii) pH; (iv) water extractability of phosphorus after incubation in soil; and (v) plant phosphorus response measured in a pot experiment with the most promising ash material. Co-gasification of straw and sludge in LT-CFB gasifiers produced ashes with a high content of recalcitrant C, phosphorus (P) and potassium (K), a low content of heavy metals (especially cadmium) and an improved plant P availability compared to the mono-sludge ashes, thereby showing the best fertilizer qualities among all assessed materials. It was also found that bottom ashes from the char reactor contained even less heavy metals than cyclone ashes. It is concluded that LT-CFB gasification and co-gasification is a highly effective way to purify and sanitize sewage sludge for subsequent use in agricultural systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of a standard operating procedure for analysis of ammonia concentrations in coal fly ash : [summary].

DOT National Transportation Integrated Search

2015-04-01

Fly ash produced when pulverized coal is burned in electrical generators can be used as a : concrete additive with many benefits. However, fly ash can have a high ammonia content, : which is released when used in concrete, potentially exposing worker...

Influence Of Trace Metal Distribution On Its Leachability From Coal Fly Ash

EPA Science Inventory

The risks associated with the reuse of coal fly ash in natural environmental settings in terms of their mobility and ecotoxicological significance is largely determined by: (1) the physicochemical conditions the fly ash is placed under; (2) the total leachable metal content in fl...

Moisture content and nutrition as selection forces for emerald ash borer larval feeding behaviour

Treesearch

Yigen Chen; Tina Ciaramitaro; Therese M. Poland

2011-01-01

The exotic phloem-feeding emerald ash borer (EAB), Agrilus planipennis, has killed tens of millions of North American ash trees (Fraxinus) since its first detection in the U.S.A. in 2002. Ash trees are killed by larval feeding in the cambial region, which disrupts translocation of photosynthates and nutrients. We observed that EAB...

Improvement of the in vitro digestible iron and zinc content of okra (Hibiscus esculentus L.) sauce widely consumed in Sahelian Africa.

PubMed

Avallone, Sylvie; Bohuon, Philippe; Hemery, Youna; Treche, Serge

2007-03-01

The effects of the formulation (okra, fish, soumbala, extract of wood ash) and cooking time of okra sauce on total iron and zinc content and on their in vitro digestibility were evaluated following a Doehlert uniform shell design with 5 factors and 33 trials. Cooking time had no significant effect on in vitro digestible iron and zinc content, whereas formulation did. Each ingredient had a specific effect. Extract of wood ash, which is a source of soluble and digestible iron and zinc, is a good way of increasing the digestible mineral content of the dish. Okra, the main ingredient in this sauce, has a negative effect and should be added in moderate quantities (< 37.7% of the DM of the sauce). An optimization using the desirability function allows us to identify the optimal recipe that enabled the quantity of digestible iron to be doubled and the quantity of digestible zinc to be increased by one third. This recipe calls for a mixture of 37.7% okra, 26.3% dried fish, 18.5% soumbala, and 3.7% extract of wood ash cooked for 25 min.

Calcium, potassium, and sodium content of forest floor arthropods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reichle, D.E.; Shanks, M.H.; Crossley, D.A. Jr.

1969-01-01

Whole-body nutrient composition of calcium, potassium, and sodium is documented for 37 species of forest floor arthropods. Sodium concentrations averaging 4.6 mg Na/g ash-free dry weight, and potassium concentrations averaging 6.2 mg K/g ash-free dry weight were relatively consistent within and among major taxonomic categories. Calcium content varied from 0.3 to 509.8 mg Ca/g ash-free dry weight, with highest values associated with Diplopoda and related species possessing highly calcified exoskeletons. Within-species variation in chemical composition often exceeded seasonal fluctuations, although several species exhibited significant temporal changes in whole-body nutrient composition of calcium, potassium, and sodium. 9 references, 3 tables.

A pilot-scale study of wet torrefaction treatment for upgrading palm oil empty fruit bunches as clean solid fuel

NASA Astrophysics Data System (ADS)

Gusman, M. H.; Sastroredjo, P. N. E.; Prawisudha, P.; Hardianto, T.; Pasek, A. D.

2017-05-01

Less utilized empty fruit bunch (EFB) is seldom used as solid biofuel due to its high alkali content that potentially cause ash deposit called slagging and fouling. This phenomenon could harm biomass-fired power plant equipment. Some pre-treatment of EFB is needed to reduce EFB ash deposit potential. The effect of wet torrefaction pre-treatment in laboratory scale was successfully proven in decreasing slagging and fouling potential while increasing EFB calorific value that could fulfill clean solid fuel criteria. This research focuses on wet torrefaction process that conducted on a pilot scale with the capacity of 250 liters. It was found that wet torrefaction process can improve the product’s calorific value up to 9.41% while reduce its ash content down to 1.01% comparing to the raw EFB. The reduction of ash content also leads to the reduction of slagging and fouling tendency that presents in terms of alkali index. Alkali index is a quantitative method that can be calculated after obtaining metal oxides fraction on solid fuel. Metal oxides could be obtained by using energy dispersive x-ray spectroscopy.

Ternary Blends of High Aluminate Cement, Fly ash and Blast-furnace slag for Sewerage Lining Mortar

NASA Astrophysics Data System (ADS)

Chao, L. C.; Kuo, C. P.

2018-01-01

High aluminate cement (HAC), fly ash (FA) and blast-furnace slag (BFS) have been treated sustainable materials for the use of cement products for wastewater infrastructure due to their capabilities of corrosion resistance. The purpose of this study is to optimize a ternary blend of above mentioned materials for a special type of mortar for sewerage lining. By the using of Taguchi method, four control parameters including water/cementitious material ratio, mix water content, fly ash content and blast-furnace slag content were considered in nine trial mix designs in this study. By evaluating target properties including (1) maximization of compressive strength, (2) maximization of electricity resistance and (3) minimization of water absorption rate, the best possible levels for each control parameter were determined and the optimal mix proportions were verified. Through the implementation of the study, a practical and completed idea for designing corrosion resistive mortar comprising HAC, FA and BSF is provided.

Assessment of the PCDD/F fate from MSWI residue used in road construction in France.

PubMed

Badreddine, R; François, D

2009-01-01

MSWI fly ash is susceptible to contain high amount of polychlorinated dibenzo-dioxins and polychlorinated dibenzo-furans. However, the use of MSWI residue for road construction started in France at a period when MSWI Bottom Ash and MSWI fly ash were not separated. From four old road sites, MSWI residue, road soils, reference soils and geo-textiles were sampled and their PCDD/F contents were analyzed. MSWI residue show a great heterogeneity but also high amounts of PCDD/F (14-2960 ng I-TEQ kg(-1)dm). Soils underlying the road show less heterogeneity and PCDD/F contents between 0.57 and 7.23 ng I-TEQ kg(-1)dm, lower than ordinary soils. Moreover, the specific analysis of the 17 toxic PCDD/F congeners (notably the 2,3,7,8-TetraCDD) indicates the very low harmfulness of road soils. The study also allows to assert the relation between the MSWI residue particle size and the PCDD/F content.

Low-rank coal oil agglomeration

DOEpatents

Knudson, Curtis L.; Timpe, Ronald C.

1991-01-01

A low-rank coal oil agglomeration process. High mineral content, a high ash content subbituminous coals are effectively agglomerated with a bridging oil which is partially water soluble and capable of entering the pore structure, and usually coal derived.

Effect of different cooking methods on proximate and mineral composition of striped snakehead fish (Channa striatus, Bloch).

PubMed

Marimuthu, K; Thilaga, M; Kathiresan, S; Xavier, R; Mas, R H M H

2012-06-01

The effects of different cooking methods (boiling, baking, frying and grilling) on proximate and mineral composition of snakehead fish were investigated. The mean content of moisture, protein, fat and ash of raw fish was found to be 77.2 ± 2.39, 13.9 ± 2.89, 5.9 ± 0.45 and 0.77 ± 0.12% respectively. The changes in the amount of protein and fat were found to be significantly higher in frying and grilling fish. The ash content increased significantly whereas that of the minerals (Na, K, Ca, Mg, Fe, Zn and Mn) was not affected in all cooking methods. Increased in Cu contents and decreased in P contents were observed in all cooking methods except grilling. In the present study, the grilling method of cooking is found to be the best for healthy eating.

Intra- and inter-unit variation in fly ash petrography and mercury adsorption: Examples from a western Kentucky power station

USGS Publications Warehouse

Hower, J.C.; Finkelman, R.B.; Rathbone, R.F.; Goodman, J.

2000-01-01

Fly ash was collected from eight mechanical and 10 baghouse hoppers at each of the twin 150-MW wall-fired units in a western Kentucky power station. The fuel burned at that time was a blend of many low-sulfur, high-volatile bituminous Central Appalachian coals. The baghouse ash showed less variation between units than the mechanical hoppers. The mechanical fly ash, coarser than the baghouse ash, showed significant differences in the amount of total carbon and in the ratio of isotropic coke to both total carbon and total coke - the latter excluding inertinite and other unburned, uncoked coal. There was no significant variation in proportions of inorganic fly ash constituents. The inter-unit differences in the amount and forms of mechanical fly ash carbon appear to be related to differences in pulverizer efficiency, leading to greater amounts of coarse coal, therefore unburned carbon, in one of the units. Mercury capture is a function of both the total carbon content and the gas temperature at the point of fly ash separation, mercury content increasing with an increase in carbon for a specific collection system. Mercury adsorption on fly ash carbon increases at lower flue-gas temperatures. Baghouse fly ash, collected at a lower temperature than the higher-carbon mechanically separated fly ash, contains a significantly greater amount of Hg.

The correlationship between the metabolizable energy content, chemical composition and color score in different sources of corn DDGS.

PubMed

Jie, Yong-Z; Zhang, Jian-Y; Zhao, Li-H; Ma, Qiu-G; Ji, Cheng

2013-09-25

This study was conducted to evaluate the apparent metabolizable energy (AME) and true metabolizable energy (TME) contents in 30 sources of corn distillers dried grains with solubles (DDGS) in adult roosters, and establish the prediction equations to estimate the AME and TME value based on its chemical composition and color score. Twenty-eight sources of corn DDGS made from several processing plants in 11 provinces of China and others imported from the United States. DDGS were analyzed for their metabolizable energy (ME) contents, measured for color score and chemical composition (crude protein, crude fat, ash, neutral detergent fiber, acid detergent fiber), to predict the equation of ME in DDGS. A precision-fed rooster assay was used, each DDGS sample was tube fed (50 g) to adult roosters. The experiment was conducted as a randomized incomplete block design with 3 periods. Ninety-five adult roosters were used in each period, with 90 being fed the DDGS samples and 5 being fasted to estimate basal endogenous energy losses. Results showed that the AME ranged from 5.93 to 12.19 MJ/kg, TME ranged from 7.28 to 13.54 MJ/kg. Correlations were found between ME and ash content (-0.64, P < 0.01) and between ME and yellowness score (0.39, P < 0.05) of the DDGS samples. Furthermore, the best-fit regression equation for AME content of DDGS based on chemical composition and color score was AME = 6.57111 + 0.51475 GE - 0.10003 NDF + 0.13380 ADF + 0.07057 fat - 0.57029 ash - 0.02437 L (R2 = 0.70). The best-fit regression equation for TME content of DDGS was TME = 7.92283 + 0.51475 GE - 0.10003 NDF + 0.13380 ADF + 0.07057 fat - 0.57029 ash - 0.02437 L (R2 = 0.70). This experiment suggested that measuring the chemical composition and color score of a corn DDGS sample may provide a quality parameter for identifying corn DDGS sources energy digestibility and metabolizable energy content.

Development and freeze-thaw durability of high flyash-content concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sajadi, J.

1987-01-01

Objectives were to investigate the effects on concrete strength, drying shrinkage, freeze-thaw durability, and air-void system parameters of replacing various amounts of portland cement with different types of fly ash and to compare selected characteristics of such fly-ash concretes and fly-ash concretes containing a high-range water-reducing admixture to those of a control mixture. It was concluded that concrete mixtures with 90-day compressive strengths equal to the control could be produced when large amounts of cement were replaced by fly ash. In addition, when the high-range water-reducing admixtures was employed, very large amounts of cement could be replaced by fly ashmore » to yield mixtures whose compressive strengths were equal to or greater than the strengths of the control mix at all ages. The maximum amount of cement that could be replaced for equal-strength mixtures depended upon the nature of the fly ash. Drying shrinkage of plain fly-ash concretes and fly-ash concretes containing the high-range water-reducing admixture were similar to those of the control mix. The optimum fly-ash content in a concrete is comparable in strength and durability to a conventional (control) concrete was influenced by the chemical and physical characteristics of the fly ash.« less

Morphological and biochemical changes in Azadirachta indica from coal combustion fly ash dumping site from a thermal power plant in Delhi, India.

PubMed

Qadir, Sami Ullah; Raja, Vaseem; Siddiqui, Weqar A

2016-07-01

The foliar and biochemical traits of Azadirachta indica A. Juss from fly ash (FA) dumping site in Badarpur thermal power plant (BTPP) New Delhi, India was studied. Three different experimental sites were selected at different distances from the thermal power plant. Ambient suspended particulate matter (SPM) and plant responses such as leaf pigments (chlorophyll a, chlorophyll b, and carotenoids), total chlorophyll, net photosynthetic rate, stomatal index (SI), stomatal conductance (SC), intercellular carbon dioxide concentration [CO2]i, net photosynthetic rate (NPR), nitrogen, nitrate, nitrate reductase activity, proline, protein, reducing sugar and sulphur content were measured. Considerable reduction in pigments (chlorophyll a, chlorophyll b and carotenoids), and total chlorophyll was observed at fly ash dumping site. Fly ash stress revealed the inhibitory effect on Nitrate reductase activity (NRA), Nitrate, soluble protein, and reducing sugar content, whereas stimulatory effect was found for the stomatal index, nitrogen, proline, antioxidants and sulphur content in the leaves. Under fly ash stress, stomatal conductance was low, leading to declining in photosynthetic rate and increase in the internal CO2 concentration of leaf. Single leaf area (SLA), leaf length and leaf width also showed a declining trend from control to the polluted site. Antioxidant enzymes increased in leaves reflecting stress and extenuation of reactive oxygen species (ROS). Copyright © 2016 Elsevier Inc. All rights reserved.

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials.

PubMed

Yilmaz, Arin; Degirmenci, Nurhayat

2009-05-01

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.

Kinetic modeling of the formation and growth of inorganic nano-particles during pulverized coal char combustion in O 2/N 2 and O 2/CO 2 atmospheres

DOE PAGES

Shaddix, Christopher R.; Niu, Yanqing; Hui, Shi'en; ...

2016-08-01

In this formation of nano-particles during coal char combustion, the vaporization of inorganic components in char and the subsequent homogeneous particle nucleation, heterogeneous condensation, coagulation, and coalescence play decisive roles. Furthermore, conventional measurements cannot provide detailed information on the dynamics of nano-particle formation and evolution, In this study, a sophisticated intrinsic char kinetics model that considers ash effects (including ash film formation, ash dilution, and ash vaporization acting in tandem), both oxidation and gasification by CO 2 and H 2O, homogeneous particle nucleation, heterogeneous vapor condensation, coagulation, and and coalescence mechanisms is developed and used to compare the temporal evolutionmore » of the number and size of nano-particles during coal char particle combustion as a function of char particle size, ash content, and oxygen content in O 2/N 2 and O 2/CO 2 atmospheres .« less

Kinetic modeling of the formation and growth of inorganic nano-particles during pulverized coal char combustion in O 2/N 2 and O 2/CO 2 atmospheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaddix, Christopher R.; Niu, Yanqing; Hui, Shi'en

In this formation of nano-particles during coal char combustion, the vaporization of inorganic components in char and the subsequent homogeneous particle nucleation, heterogeneous condensation, coagulation, and coalescence play decisive roles. Furthermore, conventional measurements cannot provide detailed information on the dynamics of nano-particle formation and evolution, In this study, a sophisticated intrinsic char kinetics model that considers ash effects (including ash film formation, ash dilution, and ash vaporization acting in tandem), both oxidation and gasification by CO 2 and H 2O, homogeneous particle nucleation, heterogeneous vapor condensation, coagulation, and and coalescence mechanisms is developed and used to compare the temporal evolutionmore » of the number and size of nano-particles during coal char particle combustion as a function of char particle size, ash content, and oxygen content in O 2/N 2 and O 2/CO 2 atmospheres .« less

Investigation of air-entraining admixture dosage in fly ash concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ley, M.T.; Harris, N.J.; Folliard, K.J.

The amount of air-entraining admixture (AEA) needed to achieve a target air content in fresh concrete can vary significantly with differences in the fly ash used in the concrete. The work presented in this paper evaluates the ability to predict the AEA dosage on the basis of tests on the fly ash alone. All results were compared with the dosage of AEA required to produce an air content of 6% in fresh concrete. Fly ash was sampled from six separate sources. For four of these sources, samples were obtained both before and after the introduction of 'low-NOx burners'. Lack ofmore » definitive data about the coal itself or the specifics of the burning processes prevents the ability to draw specific conclusions about the impact of low-NOx burners on AEA demand. Nevertheless, the data suggest that modification of the burning process to meet environmental quality standards may affect the fly ash-AEA interaction.« less

Development of the chemical and electrochemical coal cleaning process

NASA Astrophysics Data System (ADS)

Basilio, C. I.; Yoon, Roe-Hoan

The continuous testing of the Chemical and Electrochemical Coal Cleaning (CECC) was completed successfully using Middle Wyodak and Elkhorn No. 3 coal samples. The CECC unit was run under the optimum conditions established for these coal samples. For the Middle Wyodak coal, the ash content was reduced from 6.96 percent to as low 1.61 percent, corresponding to an ash rejection (by weight) of about 83 percent. The ash and sulfur contents of the Elkhorn No. 3 coal were reduced to as low as 1.8 percent and 0.9 percent. The average ash and sulfur rejections were calculated to be around 84 percent and 47 percent. The CECC continuous unit was used to treat -325 mesh Elkhorn No. 3 coal samples and gave ash and sulfur rejection values of as high as 77 percent and 66 percent. In these test, the clean -325 mesh coal particles were separated from the liberated mineral matter through microbubble column flotation, instead of wet-screening.

Optimal boiler control through real-time monitoring of unburned carbon in fly ash by laser-induced breakdown spectroscopy.

PubMed

Kurihara, Miki; Ikeda, Koji; Izawa, Yoshinori; Deguchi, Yoshihiro; Tarui, Hitoshi

2003-10-20

A laser-induced breakdown spectroscopy (LIBS) technique has been applied for detection of unburned carbon in fly ash, and an automated LIBS unit has been developed and applied in a 1000-MW pulverized-coal-fired power plant for real-time measurement, specifically of unburned carbon in fly ash. Good agreement was found between measurement results from the LIBS method and those from the conventional method (Japanese Industrial Standard 8815), with a standard deviation of 0.27%. This result confirms that the measurement of unburned carbon in fly ash by use of LIBS is sufficiently accurate for boiler control. Measurements taken by this apparatus were also integrated into a boiler-control system with the objective of achieving optimal and stable combustion. By control of the rotating speed of a mill rotary separator relative to measured unburned-carbon content, it has been demonstrated that boiler control is possible in an optimized manner by use of the value of the unburned-carbon content of fly ash.

Beneficial use of off-specification fly ashes to increase the shear strength and stiffness of expansive soil-rubber (ESR) mixtures.

DOT National Transportation Integrated Search

2011-07-01

The use of off-specification fly ashes to increase the shear strength and stiffness of an expansive soil-rubber (ESR) mixture is investigated systematically in this study. The off-specification fly ashes used include a high-sulfur content and a high-...

Arsenic and selenium capture by fly ashes at low temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Antonia Lopez-Anton; Mercedes Diaz-Somoano; D. Alan Spears

2006-06-15

Arsenic and selenium compounds may be emitted to the environment during coal conversion processes, although some compounds are retained in the fly ashes, in different proportions depending on the characteristics of the ashes and process conditions. The possibility of optimizing the conditions to achieve better trace element retention appears to be an attractive, economical option for reducing toxic emissions. This approach requires a good knowledge of fly ash characteristics and a thorough understanding of the capture mechanism involved in the retention. In this work the ability of two fly ashes, one produced in pulverized coal combustion and the other inmore » fluidized bed combustion, to retain arsenic and selenium compounds from the gas phase in coal combustion and coal gasification atmospheres was investigated. To explore the possible simultaneous retention of mercury, the influence of the unburned coal particle content was also evaluated. Retention capacities between 2 and 22 mg g{sup -1} were obtained under different conditions. The unburned coal particle content in the fly ash samples does not significantly modify retention capacities. 21 refs., 6 figs., 5 tabs.« less

Low-rank coal oil agglomeration

DOEpatents

Knudson, C.L.; Timpe, R.C.

1991-07-16

A low-rank coal oil agglomeration process is described. High mineral content, a high ash content subbituminous coals are effectively agglomerated with a bridging oil which is partially water soluble and capable of entering the pore structure, and is usually coal-derived.

Effect of processing on the biochemical contents of Acanthus montanus (Nees) T. Anderson (Acanthaceae) leaves.

PubMed

Igwe, Andrew; Eleazu, Chinedum

2018-03-01

The effect of processing on the biochemical contents of Acanthus montanus leaves was investigated. The moisture, crude protein, lipid, fiber, ash, and total carbohydrate contents of the raw vegetable were 59.15, 1.85, 2.32, 3.76, 2.04, and 34.65 g/100 g, respectively. The saponin, alkaloid, tannin, flavonoid, phenol, and anthocyanin contents of the raw vegetable were 5.35, 4.04, 1.10, 3.53, 2.87, and 1.27 g/100 g, respectively, while it contained 2.65 mg/100 g calcium, 1.14 mg/100 g magnesium, 7.66 mg/100 g potassium, 350.75 μg/g vitamin A, 50.87 mg/100 g vitamin C, and 0.25% titratable acidity. There were significant reductions ( p  < .05) in the protein, lipid, fiber, ash, saponin, alkaloid, tannin, phenol, anthocyanin, calcium, magnesium, potassium, vitamin A, vitamin C, and titratable acidity of the boiled or boiled + sun-dried A. montanus leaves; significant elevation of the moisture contents but significant reduction of the total carbohydrate contents of the boiled; and significant reduction of the moisture contents of the boiled + sun-dried vegetable compared with the raw. There were significant increases ( p  < .05) in the total carbohydrate contents of the boiled + sun-dried leaves; significant reductions ( p  < .05) in the moisture, saponin, alkaloid, and vitamins A and C contents of the sun-dried vegetable; and no significant differences ( p  > .05) in the lipid, calcium, potassium, and ash, but significant increases ( p  < .05) in the protein, crude fiber, total carbohydrates, tannins, flavonoids, phenols, anthocyanin, magnesium, and titratable acidity of the sun-dried vegetable when compared with the raw. Sun drying alone either retained or enhanced the release of some important bioactive compounds in A. montanus leaves. Furthermore, the reduced moisture content of the sun-dried vegetable together with its increased titratable acidity will make the sun-dried vegetable uninhabitable for microorganisms, thereby increasing its shelf life.

Effects of ashes from a Brazilian savanna wildfire on water, soil and biota: An ecotoxicological approach.

PubMed

Oliveira-Filho, Eduardo C; Brito, Darlan Q; Dias, Zelia M B; Guarieiro, Mayara S; Carvalho, Esther L; Fascineli, Maria L; Niva, Cintia C; Grisolia, Cesar K

2018-03-15

Wildfire is very common in Brazilian savannas, and its effects on water, soil and aquatic/soil organisms are poorly understood. In this study, we observed the effects of fire, especially of ashes, on surface soil and subsurface water in a typical Brazilian savanna (Cerrado sensu strictu) for one year. Soil analyses (pH, organic matter content, potential acidity, K, Ca, Mg and P) and subsurface water analyses (NO 3- , PO 4 3- Mg 2+ , Ca 2+ and K + ) were assessed. We evaluated the ecotoxicological effects of ashes on three different endpoints and species, in fish Danio rerio (embryonic development), aquatic snail Biomphalaria glabrata (reproduction) and a soil species Enchytraeus sp. (reproduction). We found a higher amount of exchangeable cations and organic matter content in short-term fire effects on soil, but the higher availability of nutrients did not affect the soil pH in field plots. The effects of ashes on soil and subsurface water did not persist for one-year post-fire, except for organic matter content in burned areas. No toxic effects were observed on hatching success and incidences of developmental abnormalities in D. rerio embryos. However, ash input had adverse effects on reproduction in snails and enchytraeids. We reported a statistically significant decrease in snail eggs exposed to the 50g.L -1 and 100g.L -1 of ashes after four weeks (p<0.05, Dunnett's test and Tukey test). Enchytraeus sp. reproduction was negatively influenced by the natural soil, which presents high acidity, and also when exposed directly to the ashes from burned area, suggesting that pH and other ash compounds may limit the growth of enchytraeids. More studies in burned areas are strongly encouraged, addressing the potential important routes of exposure to ashes in order to understand the impact of intense fires on soil and aquatic biota in tropical savannas. Copyright © 2017 Elsevier B.V. All rights reserved.

Application of air classification and formulation to manage feedstock cost, quality and availability for bioenergy

DOE PAGES

Thompson, Vicki S.; Lacey, Jeffrey A.; Hartley, Damon; ...

2016-04-22

Biomass such as agricultural residues, energy crops and yard waste has significant potential to be used as renewable feedstocks for production of fuels, chemicals and energy. However, in a given location, biomass availability, cost and quality can vary markedly. Strategies to manage these traits must be identified and implemented so that consistent low-cost and high-quality feedstocks can be delivered to biorefineries year round. In this study, we examine air classification as a method to mitigate high ash concentrations in corn stover, switchgrass, and grass clippings. Formulation techniques were then used to produce blends that met ash quality and biomass quantitymore » specifications at the lowest possible cost for biopower and biochemical conversion applications. It was found that air classification can separate the biomass into light fractions which contain concentrated amounts of elemental ash components introduced through soil contamination such as sodium, alumina, silica, iron and titania; and heavy fractions that are depleted in these components and have relatively lower total ash content. Light fractions of corn stover and grass clippings were found to be suitable for combustion applications since they had less propensity to slag than the whole biomass material. The remaining heavy fractions of corn stover or grass clippings could then be blended with switchgrass to produce blends that met the 5% total ash specifications suggested for biochemical conversions. However, ternary blends of the three feedstocks were not possible due to the high ash content of grass clippings. Lastly, it was determined that air classification by itself was not suitable to prepare these feedstocks for pyrolysis due to high ash content.« less

Application of air classification and formulation to manage feedstock cost, quality and availability for bioenergy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Vicki S.; Lacey, Jeffrey A.; Hartley, Damon

Biomass such as agricultural residues, energy crops and yard waste has significant potential to be used as renewable feedstocks for production of fuels, chemicals and energy. However, in a given location, biomass availability, cost and quality can vary markedly. Strategies to manage these traits must be identified and implemented so that consistent low-cost and high-quality feedstocks can be delivered to biorefineries year round. In this study, we examine air classification as a method to mitigate high ash concentrations in corn stover, switchgrass, and grass clippings. Formulation techniques were then used to produce blends that met ash quality and biomass quantitymore » specifications at the lowest possible cost for biopower and biochemical conversion applications. It was found that air classification can separate the biomass into light fractions which contain concentrated amounts of elemental ash components introduced through soil contamination such as sodium, alumina, silica, iron and titania; and heavy fractions that are depleted in these components and have relatively lower total ash content. Light fractions of corn stover and grass clippings were found to be suitable for combustion applications since they had less propensity to slag than the whole biomass material. The remaining heavy fractions of corn stover or grass clippings could then be blended with switchgrass to produce blends that met the 5% total ash specifications suggested for biochemical conversions. However, ternary blends of the three feedstocks were not possible due to the high ash content of grass clippings. Lastly, it was determined that air classification by itself was not suitable to prepare these feedstocks for pyrolysis due to high ash content.« less

Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility.

PubMed

Cao, Yan; Wang, Quan-Hai; Li, Jun; Cheng, Jen-Chieh; Chan, Chia-Chun; Cohron, Marten; Pan, Wei-Ping

2009-04-15

Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactorwas about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155 degrees C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155 degrees C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, attesting conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBr addition alone).

Combustion of horse manure for heat production.

PubMed

Lundgren, J; Pettersson, E

2009-06-01

The main objectives of this paper have been to evaluate the use of horse manure and wood-shavings as a fuel for heat production and to provide sets of data on the chemical composition, ash characteristics and ash forming elements of the fuel. Another objective has been to investigate the possibility to use the ash as fertiliser by analysing the heavy metal and nutrient contents. The results showed that the fuel is well suited for combustion for heat production causing low emissions of products of incomplete combustion. The emissions of NO(x) were however high due to the high content of fuel bound nitrogen. Emissions of CO and NO(x) were typically in the range of 30-150 mg/Nm(3) and 280-350 mg/Nm(3) at 10 vol% O(2), respectively. The analysis of the ash showed on sufficiently low concentration of heavy metals to allow recycling.

Bioprocessing of common beans in diets for tilapia: in vivo digestibility and antinutritional factors.

PubMed

Valdez-González, Francisco; Gutiérrez-Dorado, Roberto; Hernández-Llamas, Alfredo; García-Ulloa, Manuel; Sánchez-Magaña, Luís; Cuevas-Rodríguez, Breidy; Rodríguez-González, Hervey

2017-09-01

Bioprocessing of ingredients by solid-state fermentation is a low-cost technique for preparing diets. It is performed by adding microorganisms such as Rhizopus oligosporus to bean grains, achieving minimal degradation of nutrients and a significant improvement in digestibility. In particular, fermentation induces favorable changes in beans by reducing enzyme inhibitors, such as phytates and tannins. Fermentation significantly (P < 0.05) increased the protein content and digestibility of dry matter and protein compared with whole bean grains, and decreased the content of lipids, ash and phytic acid. Hardening did not have a significant (P > 0.05) effect on the chemical content of beans and digestibility of diets. The dehulled bean meal significantly (P < 0.05) increased protein and lipid content and digestibility of dry matter and protein of beans, and decreased fiber, ash and tannin content. The chemical content of beans and digestibility of ingredients compare favorably with those reported by other authors, indicating the benefits of fermentation and dehulling. We concluded that bean meal obtained from fermentation or dehulling represents a low-cost alternative for diets for tilapia. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Properties of different aged jicama (Pachyrhizus Erozus) plants

NASA Astrophysics Data System (ADS)

Nursandi, F.; Machmudi, M.; Santoso, U.; Indratmi, D.

2017-07-01

Jicama crop potential is very large, the tuber is used as a fresh fruit, ice mix fruit, salad, and can be made into flour, starch and inulin. The nutritional content of yam tubers depends on the age of the harvest, while farmers harvest jicama tubers at the age varying between 4-6 months. The research objective is to analyze the content of proximate fresh tubers and three kinds of flour (flour, starch and starch dregs) by harvesting different age plants. The study was conducted in Malang at a height of 560 m above sea level. Planting was done using plastic mulch with a spacing of 80 cm × 20 cm. Research using complete Randomized block Design with one factor harvesting consisting of 16, 18, 20 and 22 weeks after planting. Jicama tubers were harvested and analyzed the proximate for moisture, ash, fat, protein and carbohydrates in the fresh tubers, flour, starch and jicama flour dregs. The results showed that the late harvest resulted in moisture content, ash content, fiber and fat increase while the protein and carbohydrate decreased. The content of carbohydrates in the flour, starch and starch dregs was almost the same at different harvest time. The protein content of the flour is from 4.22 to 5.87%; while protein content of starch and protein content flour dregs is from 1.05 to 1.90% and 3.95 to 4.84%. Flour fiber content increased with increasing age of plants, while the fiber content of starch decreased but the dregs flour fiber content is almost the same

Proximate Composition Analysis.

PubMed

2016-01-01

The proximate composition of foods includes moisture, ash, lipid, protein and carbohydrate contents. These food components may be of interest in the food industry for product development, quality control (QC) or regulatory purposes. Analyses used may be rapid methods for QC or more accurate but time-consuming official methods. Sample collection and preparation must be considered carefully to ensure analysis of a homogeneous and representative sample, and to obtain accurate results. Estimation methods of moisture content, ash value, crude lipid, total carbohydrates, starch, total free amino acids and total proteins are put together in a lucid manner.

46 CFR 162.050-9 - Test report.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Relative density at 15 °C. (ii) Viscosity in centistokes at 37.8 °C. (iii) Flashpoint. (iv) Weight of ash content. (v) Weight of water content. (vi) Relative density at 15 °C. the of water used during testing and...

46 CFR 162.050-9 - Test report.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Relative density at 15 °C. (ii) Viscosity in centistokes at 37.8 °C. (iii) Flashpoint. (iv) Weight of ash content. (v) Weight of water content. (vi) Relative density at 15 °C. the of water used during testing and...

46 CFR 162.050-9 - Test report.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Relative density at 15 °C. (ii) Viscosity in centistokes at 37.8 °C. (iii) Flashpoint. (iv) Weight of ash content. (v) Weight of water content. (vi) Relative density at 15 °C. the of water used during testing and...

Development of a sintering process for recycling oil shale fly ash and municipal solid waste incineration bottom ash into glass ceramic composite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhikun; Zhang, Lei; Li, Aimin, E-mail: leeam@dlut.edu.cn

Highlights: • Glass ceramic composite is prepared from oil shale fly ash and MSWI bottom ash. • A novel method for the production of glass ceramic composite is presented. • It provides simple route and lower energy consumption in terms of recycling waste. • The vitrified slag can promote the sintering densification process of glass ceramic. • The performances of products decrease with the increase of oil shale fly ash content. - Abstract: Oil shale fly ash and municipal solid waste incineration bottom ash are industrial and municipal by-products that require further treatment before disposal to avoid polluting the environment.more » In the study, they were mixed and vitrified into the slag by the melt-quench process. The obtained vitrified slag was then mixed with various percentages of oil shale fly ash and converted into glass ceramic composites by the subsequent sintering process. Differential thermal analysis was used to study the thermal characteristics and determine the sintering temperatures. X-ray diffraction analysis was used to analyze the crystalline phase compositions. Sintering shrinkage, weight loss on ignition, density and compressive strength were tested to determine the optimum preparation condition and study the co-sintering mechanism of vitrified amorphous slag and oil shale fly ash. The results showed the product performances increased with the increase of sintering temperatures and the proportion of vitrified slag to oil shale fly ash. Glass ceramic composite (vitrified slag content of 80%, oil shale fly ash content of 20%, sintering temperature of 1000 °C and sintering time of 2 h) showed the properties of density of 1.92 ± 0.05 g/cm{sup 3}, weight loss on ignition of 6.14 ± 0.18%, sintering shrinkage of 22.06 ± 0.6% and compressive strength of 67 ± 14 MPa. The results indicated that it was a comparable waste-based material compared to previous researches. In particular, the energy consumption in the production process was reduced compared to conventional vitrification and sintering method. Chemical resistance and heavy metals leaching results of glass ceramic composites further confirmed the possibility of its engineering applications.« less

Nutrient content of some winter grouse foods

USGS Publications Warehouse

Treichler, R.R.; Stow, R.W.; Nelson, A.L.

1946-01-01

Seventeen preferred grouse foods were collected during the late winter and analyzed for nutrient content. The results include moisture, crude protein, ether extract, crude fiber, nitrogenfree extract, ash, calcium, phosphorus, and gross energy content expressed both on moisture free and fresh bases.....The preferred winter foods of grouse are characterized by a high content of dry substance and of nitrogen-free extract......On the basis of nutrient content, the foods examined are well qualified as sources of energy and other essential nutrients required for maintenance of grouse during the winter season.

Flexural toughness of steel fiber reinforced high performance concrete containing nano-SiO2 and fly ash.

PubMed

Zhang, Peng; Zhao, Ya-Nan; Li, Qing-Fu; Wang, Peng; Zhang, Tian-Hang

2014-01-01

This paper aims to clarify the effect of steel fiber on the flexural toughness of the high performance concrete containing fly ash and nano-SiO2. The flexural toughness was evaluated by two methods, which are based on ASTM C1018 and DBV-1998, respectively. By means of three-point bending method, the flexural toughness indices, variation coefficients of bearing capacity, deformation energy, and equivalent flexural strength of the specimen were measured, respectively, and the relational curves between the vertical load and the midspan deflection (P(V)-δ) were obtained. The results indicate that steel fiber has great effect on the flexural toughness parameters and relational curves (P(V)-δ) of the three-point bending beam specimen. When the content of steel fiber increases from 0.5% to 2%, the flexural toughness parameters increase gradually and the curves are becoming plumper and plumper with the increase of steel fiber content, respectively. However these flexural toughness parameters begin to decrease and the curves become thinner and thinner after the steel fiber content exceeds 2%. It seems that the contribution of steel fiber to the improvement of flexural toughness of the high performance concrete containing fly ash and nano-SiO2 is well performed only when the steel fiber content is less than 2%.

Susceptibility of volcanic ash-influenced soil in northern Idaho to mechanical compaction

Treesearch

Deborah S. Page-Dumroese

1993-01-01

Timber harvesting and mechanical site preparation can reduce site productivity if they excessively disturb or compact the soil. Volcanic ash-influenced soils with low undisturbed bulk densities and rock content are particularly susceptible. This study evaluates the effects of harvesting and site preparation on changes in the bulk density of ash-influenced forest soils...

Nutrient status of crop contents of rural scavenging local chickens in Tanzania.

PubMed

Mwalusanya, N A; Katule, A M; Mutayoba, S K; Minga, U M; Mtambo, M M A; Olsen, J E

2002-03-01

1. A total of 144 chickens purchased from peasants in Morogoro, Tanzania were slaughtered, their crops dissected and the contents analysed. The birds consisted of 48 chickens from each of three climatic zones (warm and wet, warm and dry, cool and wet). Seventy-two chickens were slaughtered in each season, that is short rainy and long rainy season. 2. Cereal grains, bran, green forages, insects/worms and kitchen food wastes were the main crop contents and their composition varied significantly with season and climate. 3. The overall mean chemical compositions (g/kg) of the crop contents were: 430.8 +/- 107.78 dry matter (DM), 104.4 +/- 43.47 crude protein (CP), 61.2 +/- 36.48 ether extract (EE), 58.2 +/- 26.29 crude fibre (CF), 125.4 +/- 58-27 ash, 6.3 +/- 5.19 calcium (Ca) and 3.6 +/- 2.41 phosphorus (P). 4. CP, EE, ash and P contents varied significantly (P<0.05) with season but contents of DM, CF and Ca were not significantly different. 5. CP content was significantly higher (P<0.05) in growers than in adults while the reverse was true for Ca content. Other variables did not differ significantly. 6. Significant differences (P<0.05) in chemical composition were observed among the zones in all parameters except for CP content. 7. The study showed that the chemical composition of feeds eaten by rural scavenging chickens was below the nutritional requirements and varied with season, climate and age of birds.

Differences in gasification behaviors and related properties between entrained gasifier fly ash and coal char

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jing Gu; Shiyong Wu; Youqing Wu

2008-11-15

In the study, two fly ash samples from Texaco gasifiers were compared to coal char and the physical and chemical properties and reactivity of samples were investigated by scanning electron microscopy (SEM), SEM-energy-dispersive spectrometry (EDS), X-ray diffraction (XRD), N{sub 2} and CO{sub 2} adsorption method, and isothermal thermogravimetric analysis. The main results were obtained. The carbon content of gasified fly ashes exhibited 31-37%, which was less than the carbon content of 58-59% in the feed coal. The fly ashes exhibited higher Brunauer-Emmett-Teller (BET) surface area, richer meso- and micropores, more disordered carbon crystalline structure, and better CO{sub 2} gasification reactivitymore » than coal char. Ashes in fly ashes occurred to agglomerate into larger spherical grains, while those in coal char do not agglomerate. The minerals in fly ashes, especial alkali and alkaline-earth metals, had a catalytic effect on gasification reactivity of fly ash carbon. In the low-temperature range, the gasification process of fly ashes is mainly in chemical control, while in the high-temperature range, it is mainly in gas diffusion control, which was similar to coal char. In addition, the carbon in fly ashes was partially gasified and activated by water vapor and exhibited higher BET surface area and better gasification activity. Consequently, the fact that these carbons in fly ashes from entrained flow gasifiers are reclaimed and reused will be considered to be feasible. 15 refs., 7 figs., 5 tabs.« less

Porosity, Mineralization, Tissue Type and Morphology Interactions at the Human Tibial Cortex

NASA Astrophysics Data System (ADS)

Hampson, Naomi A.

Prior research has shown a relationship between tibia robustness (ratio of cross-sectional area to bone length) and stress fracture risk, with less robust bones having a higher risk, which may indicate a compensatory increase in elastic modulus to increase bending strength. Previous studies of human tibiae have shown higher ash content in slender bones. In this study, the relationships between variations in volumetric porosity, ash content, tissue mineral density, secondary bone tissue, and cross sectional geometry, were investigated in order to better understand the tissue level adaptations that may occur in the establishment of cross-sectional properties. In this research, significant differences were found between porosity, ash content, and tissue type around the cortex between robust and slender bones, suggesting that there was a level of co-adaption occurring. Variation in porosity correlated with robustness, and explained large parts of the variation in tissue mineral density. The nonlinear relationship between porosity and ash content may support that slender bones compensate for poor geometry by increasing ash content through reduced remodeling, while robust individuals increase porosity to decrease mass, but only to a point. These results suggest that tissue level organization plays a compensatory role in the establishment of adult bone mass, and may contribute to differences in bone aging between different bone phenotypes. The results suggest that slender individuals have significantly less remodeled bone, however the proportion of remodeled bone was not uniform around the tibia. In the complex results of the study of 38% vs. 66% sites the distal site was subject to higher strains than the 66% site, indicating both local and global regulators may be affecting overall remodeling rates and need to be teased apart in future studies. This research has broad clinical implications on the diagnosis and treatment of fragility fractures. The relationships that were found between local variables and global geometry indicate that there was a fundamental difference between robust and slender bones, which affect the overall properties of the bone. This could allow for simple testing of bone geometry to predict an individual's fracture risk.

The measurement of unburned carbon in fly ash using infrared photoacoustics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waller, D.J.; Brown, R.C.

1995-12-31

Unburned carbon in fly ash yields valuable information on coal combustion efficiency in coal-fired boilers. The carbon content of fly ash is also an important parameters in the sale of fly ash for Portland cement. Unfortunately, a reliable and inexpensive instrument for measuring unburned carbon is not commercially available. The authors have developed an off-line instrument that detects carbon in fly ash via the photoacoustic effect. In this process, amplitude-modulated radiation is absorbed by a bulk sample of fly ash. The wavelength of the radiation is chosen such that mineral compounds and moisture in the fly ash are transparent tomore » the radiation but carbon is strongly absorbing. The modulated absorption generates a periodic pressure wave at the surface of the sample which propagates through the surrounding air as an acoustic wave. This wave is detected by a sensitive microphone, and is dependent on the carbon content of the sample. The resulting instrument has been used to measure fly ash carbon concentrations from less than 0.1% to nearly 7% by mass. The precision of these measurements is nominally within 4%, which is equivalent to the precision of the chemical analysis used to develop the calibration standards. The applicability of a theoretical model to the empirical results is discussed with respect to fly ash sample preparation.« less

Controlling formaldehyde emissions with boiler ash.

PubMed

Cowan, Jennifer; Abu-Daabes, Malyuba; Banerjee, Sujit

2005-07-01

Fluidized wood ash reduces formaldehyde in air from about 20 to <1 ppmv. Methanol is removed to a much lower extent. The efficiency of formaldehyde reduction increases with increasing moisture content of the ash. Sorption of formaldehyde to ash can be substantially accounted for by partitioning to the water contained in the ash followed by rate-controlling binding to the ash solids. Adsorption occurs at temperatures of up to 165 degrees C; oxidation predominates thereafter. It is proposed that formaldehyde could be stripped from an air stream in a fluidized bed containing ash, which could then be returned to a boiler to incinerate the formaldehyde.

Proximate nutrient analyses of four species of submerged aquatic vegetation consumed by Florida manatee (Trichechus manatus latirostris) compared to romaine lettuce (Lactuca sativa var. longifolia).

PubMed

Siegal-Willott, Jessica L; Harr, Kendal; Hayek, Lee-Ann C; Scott, Karen C; Gerlach, Trevor; Sirois, Paul; Reuter, Mike; Crewz, David W; Hill, Richard C

2010-12-01

Free-ranging Florida manatees (Trichechus manatus latirostris) consume a variety of sea grasses and algae. This study compared the dry matter (DM) content, proximate nutrients (crude protein [CP], ether-extracted crude fat [EE], nonfiber carbohydrate [NFC], and ash), and the calculated digestible energy (DE) of sea grasses (Thalassia testudinum, Halodule wrightii, and Syringodium filiforme) collected in spring, summer, and winter, and an alga (Chara sp.) with those of romaine lettuce (Lactuca sativa var. longifolia). Neutral-detergent fiber (NDF), acid-detergent fiber (ADF), and lignin (L) measured after ash-extraction were also compared. Results of statistical tests (C = 0.01) revealed DM content was higher in aquatic vegetation than in lettuce (P = 0.0001), but NDF and ADF were up to threefold greater, EE (P = 0.00001) and CP (P = 0.00001) were 2-9 times less, and NFC (P = 0.0001) was 2-6 times lower in sea grass than in lettuce, on a DM basis. Chara was lower in NDF, ADF, L, EE, CP, and NFC relative to lettuce on a DM basis. Ash content (DM basis) was higher (P = 0.0001), and DE was 2-6 times lower in aquatic vegetation than in lettuce. Sea grass rhizomes had lower L and higher ash contents (DM basis) than sea grass leaves. Based on the nutrient analyses, romaine lettuce and sea grasses are not equivalent forages, which suggests that the current diet of captive Florida manatees should be reassessed.

40 CFR Table F-2 to Subpart F of... - Default Data Sources for Parameters Used for CO2 Emissions

Code of Federal Regulations, 2014 CFR

2014-07-01

... metric ton Al (metric tons C/metric tons Al) Individual facility records. Sa: sulfur content in baked anode (percent weight) 2.0. Asha: ash content in baked anode (percent weight) 0.4. CO2 Emissions From... records. Hw: annual hydrogen content in green anodes (metric tons) 0.005 × GA. BA: annual baked anode...

40 CFR Table F-2 to Subpart F of... - Default Data Sources for Parameters Used for CO2 Emissions

Code of Federal Regulations, 2013 CFR

2013-07-01

... metric ton Al (metric tons C/metric tons Al) Individual facility records. Sa: sulfur content in baked anode (percent weight) 2.0. Asha: ash content in baked anode (percent weight) 0.4. CO2 Emissions From... records. Hw: annual hydrogen content in green anodes (metric tons) 0.005 × GA. BA: annual baked anode...

40 CFR Table F-2 to Subpart F of... - Default Data Sources for Parameters Used for CO2 Emissions

Code of Federal Regulations, 2012 CFR

2012-07-01

... metric ton Al (metric tons C/metric tons Al) Individual facility records. Sa: sulfur content in baked anode (percent weight) 2.0. Asha: ash content in baked anode (percent weight) 0.4. CO2 Emissions From... records. Hw: annual hydrogen content in green anodes (metric tons) 0.005 × GA. BA: annual baked anode...

40 CFR Table F-2 to Subpart F of... - Default Data Sources for Parameters Used for CO2 Emissions

Code of Federal Regulations, 2011 CFR

2011-07-01

... metric ton Al (metric tons C/metric tons Al) Individual facility records. Sa: sulfur content in baked anode (percent weight) 2.0. Asha: ash content in baked anode (percent weight) 0.4. CO2 Emissions From... records. Hw: annual hydrogen content in green anodes (metric tons) 0.005 × GA. BA: annual baked anode...

Effect of dietary protein and lipid levels on growth, nutrient utilization and whole-body composition of blue gourami, Trichogaster trichopterus fingerlings.

PubMed

Mohanta, K N; Subramanian, S; Korikanthimath, V S

2013-02-01

Nine semi-purified diets were prepared with three levels each of protein (300, 350 and 400 g/kg) and lipid (60, 80 and 100 g/kg) and fed ad libitum to Trichogaster trichopterus fingerlings (0.61 ± 0.03 g) in triplicate groups (10 fish/replicate) for 90 days to determine optimum dietary protein and lipid levels. Twenty-seven flow-through fibre-reinforced plastic tanks (200 l capacity each with 100 l of water) were used for rearing the fish. The dietary protein, lipid and their interactions had significant effects (p < 0.05) on weight gain, feed conversion ratio, specific growth rate, nutrient retention and digestibility, but not on hepato- and viscerosomatic indexes (p > 0.05). Dietary protein and the interaction of protein with lipid had significant effect (p < 0.05) on whole-body dry matter, lipid and energy contents, but not on protein and ash contents (p > 0.05). But, the dietary lipid had significant (p < 0.05) effect on whole-body dry matter, protein, lipid and energy contents except the ash contents (p > 0.05). For each level of dietary protein, the increase in dietary lipid resulted significant increase (p < 0.05) in whole-body lipid contents without affecting the protein and ash contents (p > 0.05). Based on better growth and dietary performances, the optimum dietary protein and lipid levels of blue gourami fingerling are 350 and 80 g/kg diet respectively. © 2011 Blackwell Verlag GmbH.

Ash characteristics and plant nutrients in some aquatic biomasses

NASA Astrophysics Data System (ADS)

Masto, Reginald; Pandit, Ankita; George, Joshy; Mukhopadhyay, Sangeeta; Selvi, Vetrivel; Ram, Lal

2016-04-01

Aquatic biomasses are explored as potential fuel source for direct combustion because of their faster growth and no land requirement. The energy density and the ash characteristics of the aquatic biomasses are to be evaluated for their suitability for energy extraction. In the study, four aquatic plant samples namely Eichornia crassipes, Hydrilla verticilleta, Lemna minor, Spirogyra spp were collected from a pond in Digwadih Campus of Central Institute of Mining and Fuel Research, Dhanbad. The biomasses were air dried, powdered and ashed at different temperatures. Volatile C was relatively lower in Spirogyra and Hydrilla (53 %) than Eichornia (62.6 %) or Lemna (59.7 %), whereas fixed C was higher for Eichornia and Lemna (about 10 %) and lower for Hydrilla (1 %). Ultimate analysis showed that the carbon content was in the order Eichornia > Lemna > Spirogyra > Hydrilla. The IR spectra of each raw biomass is compared to their respective ashes obtained at different temperatures (500-900°C). With increase in ashing temperature from 500-900°C there is gradual breakdown of the cellulosic structure hence, peaks around 2900-2800cm-1 caused by aliphatic C-H vibration tends to disappear slowly in ash. More number of peaks appears at lower wavenumbers in ashes of all the biomass samples indicating towards increased percentage of inorganic ion species. Considerable enrichment of SiO2 is validated with prominent peaks at 1100-900 cm-1 in all the ashes. Lemna and Spirogyra has a similar ash composition (Si > Al > Ca > K), whereas, Ca was higher in Hydrilla (Si > Ca > K > Al). Eichornia (Si > K > Ca > Al) has higher K and Ca than Al. SiO2 and Al2O3 were higher in Spirogyra, while SiO2 and CaO in Eichornia and Hydrilla. K first increased from 500-700/800⁰C, and then decreased from 800-900⁰C. Cl is lost slowly in ash from 500-700/800⁰C and then by a drastic reduction from 800-900⁰C. S is enhanced in ash at all temperatures although the change is quite small. Most of the Cl is released at 800 °C. The salgging tendencies based on both base: acid ratio and slagging factor, fouling probabilities based on fouling factors is in the order Hydrilla > Eichornia > Lemna > Spirogyra. Among the different heavy metals Zn, Pb, Cu, and Ni have concentration > 100 mg/kg; Cr and V content was > 50 mg/kg; Co, > 10 mg/kg. In general the heavy metal contents were higher in Spirogyra. Due to the volatile nature Cd and Pb decreases in ash with temperature and is lost continuously in flue gas. Plant nutrient content was relatively higher for Eichornia: K (8 - 12.8 %), P (5.7 - 7.3 %), Ca (9.2 - 10.8 %), Mg (2.8 - 3.6 %), S (1.9 - 2.9 %), Zn (0.033 - 0.045 %), Fe (3.3 - 4.7 %), Cu (0.009 - 0.013 %), Mn (0.8 -1.3%). Among the four biomasses we have studied, Eichornia could be a potential candidate for energy extraction in view of its C content and widespread availability in many parts of the globe, and fast multiplication associated with the eutrophication of water bodies.

Sulfidation treatment of molten incineration fly ashes with Na2S for zinc, lead and copper resource recovery.

PubMed

Kuchar, D; Fukuta, T; Onyango, M S; Matsuda, H

2007-04-01

The present study focuses on the conversion of heavy metals involved in molten incineration fly ashes to metal sulfides which could be thereafter separated by flotation. The sulfidation treatment was carried out for five molten incineration fly ashes (Fly ash-A to Fly ash-E) by contacting each fly ash with Na(2)S solution for a period of 10 min to 6h. The initial molar ratio of S(2-) to Me(2+) was adjusted to 1.20. The conversion of heavy metals to metal sulfides was evaluated by measuring the S(2-) residual concentrations using an ion selective electrode. The formation of metal sulfides was studied by XRD and SEM-EDS analyses. In the case of Fly ash-A to Fly ash-D, more than 79% of heavy metals of zinc, lead and copper was converted to metal sulfides within the contacting period of 0.5h owing to a fast conversion of metal chlorides to metal sulfides. By contrast, the conversion of about 35% was achieved for Fly ash-E within the same contacting period, which was attributed to a high content of metal oxides. Further, the S(2-) to Me(2+) molar ratio was reduced to 1.00 to minimize Na(2)S consumption and the conversions obtained within the contacting period of 0.5h varied from 76% for Fly ash-D to 91% for Fly ash-C. Finally, soluble salts such as NaCl and KCl were removed during the sulfidation treatment, which brought about a significant enrichment in metals content by a factor varying from 1.5 for Fly ash-D to 4.9 for Fly ash-A.

NASA EO-1 Spacecraft Images Chile Volcanic Eruption

NASA Image and Video Library

2011-06-17

On June 14, 2011, NASA Earth Observing-1 EO-1 spacecraft obtained this image showing ash-rich volcanic plume billowing out of the vent, punching through a low cloud layer. The plume grey color is a reflection of its ash content.

Recovery of gallium and vanadium from gasification fly ash.

PubMed

Font, Oriol; Querol, Xavier; Juan, Roberto; Casado, Raquel; Ruiz, Carmen R; López-Soler, Angel; Coca, Pilar; García Peña, Francisco

2007-01-31

The Puertollano Integrated Coal Gasification Combined Cycle (IGCC) Power Plant (Spain) fly ash is characterized by a relatively high content of Ga and V, which occurs mainly as Ga2O3 and as Ga3+ and V3+ substituting for Al3+ in the Al-Si fly ash glass matrix. Investigations focused on evaluating the potential recovery of Ga and V from these fly ashes. Several NaOH based extraction tests were performed on the IGCC fly ash, at different temperatures, NaOH/fly ash (NaOH/FA) ratios, NaOH concentrations and extraction times. The optimal Ga extraction conditions was determined as 25 degrees C, NaOH 0.7-1 M, NaOH/FA ratio of 5 L/kg and 6 h, attaining Ga extraction yields of 60-86%, equivalent to 197-275 mg of Ga/kg of fly ash. Re-circulation of leachates increased initial Ga concentrations (25-38 mg/L) to 188-215 mg/L, while reducing both content of impurities and NaOH consumption. Carbonation of concentrated Ga leachate demonstrated that 99% of the bulk Ga content in the leachate precipitates at pH 7.4. At pH 10.5 significant proportions of impurities, mainly Al (91%), co-precipitate while >98% of the bulk Ga remains in solution. A second carbonation of the remaining solution (at pH 7.5) recovers the 98.8% of the bulk Ga. Re-dissolution (at pH 0) of the precipitate increases Ga purity from 7 to 30%, this being a suitable Ga end product for further purification by electrolysis. This method produces higher recovery efficiency than currently applied for Ga on an industrial scale. In contrast, low V extraction yields (<64%) were obtained even when using extreme alkaline extraction conditions, which given the current marked price of this element, limits considerably the feasibility of V recovery from IGCC fly ash.

Characterization of coal fly ash components by laser-induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Ctvrtnickova, Tereza; Mateo, Mari-Paz; Yañez, Armando; Nicolas, Gines

2009-10-01

The high sensitivity of laser-induced breakdown spectroscopy (LIBS) for the detection of most of the fly ash components enables the analysis of these residues produced during the combustion of coal. Fly ash consists of oxides (SiO 2, Al 2O 3, Fe 2O 3, CaO…) and unburnt carbon which is the major determinant of combustion efficiency in coal fired boilers. For example, an excessive amount of residual carbon dispersed in the fly ash means a significant loss of energy (Styszko et al., 2004 [1]). Standard methods employed for the analysis of fly ash make not possible a control of boiler in real time. LIBS technique can significantly reduce the time of analysis, in some cases even an online detection can be performed. For this reason, some studies have been addressed in order to demonstrate the capability of the laser-induced breakdown spectroscopy technique for the detection of carbon content in high pressure conditions typical of thermal power plants (Noda et al., 2002 [2]) and for the monitoring of unburnt carbon for the boiler control in real time (Kurihara et al., 2003 [3]). In particular, the content of unburnt carbon is a valuable indicator for the control of fly ash quality and for the boiler combustion. Depending on this unburnt carbon content, fly ash can be disposed as an industrial waste or as a raw material for the production of concrete in the construction sector. In this study, analyses were performed on specimens of various forms of preparation. Pressed pellets were prepared with two different binders. Presented results concern the nature and amount of the binder used to pelletize the powder, and the laser-induced breakdown spectroscopy parameters and procedure required to draw calibration curves of elements from the fly ash. Analysis "on tape" was performed in order to establish the experimental conditions for the future "online analysis".

Cellulose, hemicelluloses, lignin and ash content of some organic materials and their suitability for use as paper pulp supplements.

PubMed

Ververis, C; Georghiou, K; Danielidis, D; Hatzinikolaou, D G; Santas, P; Santas, R; Corleti, V

2007-01-01

Freshwater algal biomass and orange and lemon peels were assessed as tissue paper pulp supplements. Cellulose and hemicellulose contents of algal biomass were 7.1% and 16.3%, respectively, whereas for citrus peels cellulose content ranged from 12.7% to 13.6% and hemicellulose from 5.3% to 6.1%. For all materials, lignin and ash content was 2% or lower, rendering them suitable for use as paper pulp supplements. The addition of algal biomass to paper pulp increased its mechanical strength significantly. However, brightness was adversely affected by chlorophyll. The addition of citrus peels in paper pulp had no effect on breaking length, increased bursting strength and decreased tearing resistance. Brightness was negatively affected at proportions of 10%, because citrus peel particles behave as coloured pigments. The cost of both materials is about 45% lower than that of conventional pulp, resulting in a 0.9-4.5% reduction in final paper price upon their addition to the pulp.

Blackberry wines mineral and heavy metal content determination after dry ashing: multivariate data analysis as a tool for fruit wine quality control.

PubMed

Amidžić Klarić, Daniela; Klarić, Ilija; Mornar, Ana; Velić, Darko; Velić, Natalija

2015-08-01

This study brings out the data on the content of 21 mineral and heavy metal in 15 blackberry wines made of conventionally and organically grown blackberries. The objective of this study was to classify the blackberry wine samples based on their mineral composition and the applied cultivation method of the starting raw material by using chemometric analysis. The metal content of Croatian blackberry wine samples was determined by AAS after dry ashing. The comparison between an organic and conventional group of investigated blackberry wines showed statistically significant difference in concentrations of Si and Li, where the organic group contained higher concentrations of these compounds. According to multivariate data analysis, the model based on the original metal content data set finally included seven original variables (K, Fe, Mn, Cu, Ba, Cd and Cr) and gave a satisfactory separation of two applied cultivation methods of the starting raw material.

Effect of adding acid solution on setting time and compressive strength of high calcium fly ash based geopolymer

NASA Astrophysics Data System (ADS)

Antoni, Herianto, Jason Ghorman; Anastasia, Evelin; Hardjito, Djwantoro

2017-09-01

Fly ash with high calcium oxide content when used as the base material in geopolymer concrete could cause flash setting or rapid hardening. However, it might increase the compressive strength of geopolymer concrete. This rapid hardening could cause problems if the geopolymer concrete is used on a large scale casting that requires a long setting time. CaO content can be indicated by pH values of the fly ash, while higher pH is correlated with the rapid setting time of fly ash-based geopolymer. This study investigates the addition of acid solution to reduce the initial pH of the fly ash and to prolong the setting time of the mixture. The acids used in this study are hydrochloric acid (HCl), sulfuric acid (H2 SO4), nitric acid (HNO3) and acetic acid (CH3 COOH). It was found that the addition of acid solution in fly ash was able to decrease the initial pH of fly ash, however, the initial setting time of geopolymer was not reduced. It was even faster than that of the control mixture. The acid type causes various influence, depending on the fly ash properties. In addition, the use of acid solution in fly ash reduces the compressive strength of geopolymer mortar. It is concluded that the addition of acid solution cannot prolong the rapid hardening of high calcium fly ash geopolymer, and it causes adverse effect on the compressive strength.

Comparison of Glass Powder and Fly Ash Effect on the Fresh Properties of Self-Compacting Mortars

NASA Astrophysics Data System (ADS)

Öznur Öz, Hatice; Erhan Yücel, Hasan; Güneş, Muhammet

2017-10-01

This study is aimed to determine effects of glass powder on fresh properties of self-compacting mortars. Self-compacting mortars incorporating glass powder (SCMGPs) were designed with a water/binder ratio of 0.40 and a total binder content of 550 kg/m3. At first, the control mixture was produced with 20% fly ash and % 80 cement of the total binder content without using the glass powder. Then, glass powder was used in the proportions 5%, 10%, 15% and 20% instead of fly ash in the mortars. Mini-slump flow and mini-v funnel tests experimentally investigated on SCMGPs to compare the effect of fly ash and glass powder. With increasing the amount of glass powder used in SCMGPs increased the amount of superplasticizer used to obtain the desired mini-slump flow diameter. So, the use of glass powder reduced the flow ability of SCMGPs in comparison to fly ash. Additionally, the compressive strength and flexural strength of the mortar mixtures were determined at the 28th day. The test results indicated that the mechanical characteristics of SCMGPs improved when the fly ash was replaced with glass powder in SCMGPs.

Procedural uncertainties of Proctor compaction tests applied on MSWI bottom ash.

PubMed

Izquierdo, Maria; Querol, Xavier; Vazquez, Enric

2011-02-28

MSWI bottom ash is a well-graded highly compactable material that can be used as a road material in unbound pavements. Achieving the compactness assumed in the design of the pavement is of primary concern to ensure long term structural stability. Regulations on road construction in a number of EU countries rely on standard tests originally developed for natural aggregates, which may not be appropriate to accurately assess MSWI bottom ash. This study is intended to assist in consistently assessing MSWI bottom ash compaction by means of the Proctor method. This test is routinely applied to address unbound road materials and suggests two methods. Compaction parameters show a marked procedural dependency due to the particle morphology and weak particle strength of ash. Re-compacting a single batch sample to determine Proctor curves is a common practise that turns out to overvalue optimum moisture contents and maximum dry densities. This could result in wet-side compactions not meeting stiffness requirements. Inaccurate moisture content measurements during testing may also induce erroneous determinations of compaction parameters. The role of a number of physical properties of MSWI bottom ash in compaction is also investigated. Copyright © 2011 Elsevier B.V. All rights reserved.

Utilization of fly ash as partial sand replacement in oil palm shell lightweight aggregate concrete

NASA Astrophysics Data System (ADS)

Nazrin Akmal, A. Z. Muhammad; Muthusamy, K.; Mat Yahaya, F.; Hanafi, H. Mohd; Nur Azzimah, Z.

2017-11-01

Realization on the increasing demand for river sand supply in construction sector has inspired the current research to find alternative material to reduce the use of natural sand in oil palm shell lightweight aggregate concrete (OPS LWAC) production. The existence of fly ash, a by-product generated from coal power plant, which pose negative impact to the environment when it is disposed as waste, were used in this research. The effect of fly ash content as partial sand replacement towards workability and compressive strength of OPS lightweight aggregate concrete were investigated. Four concrete mixes containing various percentage of fly ash that are 0%, 10%, 20% and 30% by weight of sand were used in the experimental work. All mixes were cast in form of cubes before subjected to water curing until the testing age. Compressive strength test were conducted at 1, 3, 7 and 28 days. The finding shows that the workability of the OPS LWAC decreases when more fly ash are used as sand replacement. It was found that adding of 10% fly ash as sand replacement content resulted in better compressive strength of OPS LWAC, which is higher than the control mix.

Effect of fly ash content towards Sulphate resistance of oil palm shell lightweight aggregate concrete

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Fadzil, M. Y.; Nazrin Akmal, A. Z. Muhammad; Ahmad, S. Wan; Nur Azzimah, Z.; Hanafi, H. Mohd; Mohamad Hafizuddin, R.

2018-04-01

Both oil palm shell (OPS) and fly ash are by-product generated from the industries. Disposal of these by-product as wastes cause negative impact to the environment. The use of both oil palm shell and fly ash in concrete is seen as an economical solution for making green and denser concrete. The primary aim of this research is to determine the effects of FA utilization as sand replacement in oil palm shell lightweight aggregate concrete (OPS LWAC) towards sulphate resistance. Five concrete mixes containing fly ash as sand replacement namely 0%, 10%, 20%, 30% and 40% were prepared in these experimental work. All mixes were cast in form of cubes before subjected to sulphate solution for the period of 5 months. It was found that addition of 10% fly ash as sand replacement content resulted in better sulphate resistance of OPS LWAC. The occurrence of pozzolanic reaction due to the presence of FA in concrete has consumed the vulnerable Calcium hydroxide to be secondary C-S-H gel making the concrete denser and more durable.

Proximate composition and energy density of some North Pacific forage fishes

USGS Publications Warehouse

van Pelt, Thomas I.; Piatt, John F.; Lance, Brian K.; Roby, Daniel D.

1997-01-01

Mature pelagic forage fish species (capelin, sand lance, squid) had greater lipid concentrations than juvenile age-classes of large demersal and pelagic fish species (walleye pollock, Pacific cod, Atka mackerel, greenling, prowfish, rockfish, sablefish). Myctophids preyed on by puffins have at least twice as much lipid per gram compared to mature capelin, sand lance and squid, and an order of magnitude greater lipid concentrations than juvenile forage fish. Energy density of forage fishes was positively correlated with lipid content, and negatively correlated with water, ash-free lean dry mass (mostly protein), and ash contents.

Physico-chemical analysis and antimicrobial potential of Apis dorsata, Apis mellifera and Ziziphus jujube honey samples from Pakistan

PubMed Central

Fahim, Hira; Dasti, Javid Iqbal; Ali, Ihsan; Ahmed, Safia; Nadeem, Muhammad

2014-01-01

Objective To evaluate physico-chemical properties and antimicrobial potential of indigenous honey samples against different reference strains including Escherichia coli ATCC 8739, Enterobacter aerogenes ATCC 13048, Pseudomonas aeroginosa ATCC 9027, Bacillus subtilis ATCC 6633, Staphylococcus aureus ATCC 25923, Salmonella typhi ATCC 14028, Klebsiella pneumonia ATCC 13883, Aspergillus niger ATCC 16404, Rhizopus oligosporus PCSIR1, Candida albicans ATCC 14053 and Candida utilis ATCC 9950. Methods By using standard methods samples were evaluated for their antimicrobial properties including additive effect of starch and non-peroxidase activity, antioxidative properties (phenol contents, flavonoid contents, 1,1-diphenyl-2-picrylhydrazyl radical scavenging activity). Prior to this evaluation, complete physico-chemical properties including pH, color, ash contents, protein contents, moisture contents, hydroxymethyl furfural contents, total sugar contents, reducing sugar and non-reducing sugar contents were analyzed. Results Relatively higher ash contents were found in the Siddar honey i.e. (0.590 0±0.033 6)% and small honey showed relatively higher protein contents i.e. (777.598±9.880) mg/kg. The moisture contents of tested honey samples ranged between 13.8%-16.6%, total sugar contents from 61.672%-72.420% and non-reducing sugar contents from 1.95%-3.93%. Presences of phenolic contents indicate higher antioxidant potential of these honey samples. All bacteria showed clear inhibition zones in response to tested honey samples whereas fungi and yeast showed inhibition at higher concentrations of these honey samples. For Escherichia coli, Bacillus subtilis, Salmonella typhi, Pseudomonas aeroginosa and Aspergillus niger, overall the small honey showed the higher activity than other honey samples. Conclusion Physico-chemical analysis of honey samples confirmed good quality of honey according to the standards set by European Union Commission and Codex Alimentarius Commission. Evaluation of these honey samples confirms antimicrobial potential of particular types of honeys indigenous to Pakistan. PMID:25183333

Environmental characterisation of sewage sludge/paper ash-based composites in relation to their possible use in civil engineering.

PubMed

Mladenovič, Ana; Hamler, Sandra; Zupančič, Nina

2017-01-01

The environmental acceptability of geotechnical composites made of treated municipal sewage sludge (SwS) and paper ash (PA) after two different curing periods has been investigated. The mineral composition of such composites, including their content of major oxides, is mainly influenced by the PA. The content of potentially toxic elements (PTEs) in the initial materials and in the composites varies considerably. In the SwS the Ba, Cd, Cr, Cu, Hg, Ni and Zn contents are above the legally permitted limits. The PTE content of PA are lower, but still somewhat above the permitted values for Ba and Cu. Mixing these two materials together resulted in a decrease in the PTE, but the Ba, Cu and Zn contents are still too high for agricultural application. However, leachates from composites that had been cured for 28 days are highly alkaline, and the As, Ba, Cd, Cr, Hg, Mo, Ni, Pb and Zn contents in them are well below the permitted values. The Cu contents (2.4 to 5.4 mg/kg) are above the permitted limit for inert material, but inside the range for non-hazardous material. In a leachate of composite which was prepared with fresh PA and a lower PA to SwS ratio, the Cu content was 1.4 mg/kg, since fresh PA is more reactive and therefore has a higher ability to immobilise Cu. Therefore, such mixtures can be utilised for covers and liners for sanitary landfills.

Switchgrass growth and effects on biomass accumulation, moisture content, and nutrient removal

USDA-ARS?s Scientific Manuscript database

Temporal patterns of plant growth, composition, and nutrient removal impact development of models for predicting optimal harvest times of switchgrass (Panicum virgatum L.) for bioenergy. Objectives were to characterize seasonal trends in yield, tissue moisture, ash content, leaf area index (LAI), in...

40 CFR 98.63 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... emissions from anode consumption during electrolysis and anode baking of prebake cells using either the.../metric tons Al). MP = Annual metal production (metric tons Al). Sa = Sulfur content in baked anode (percent weight). Asha = Ash content in baked anode (percent weight). 44/12 = Ratio of molecular weights...

40 CFR 98.63 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... emissions from anode consumption during electrolysis and anode baking of prebake cells using either the.../metric tons Al). MP = Annual metal production (metric tons Al). Sa = Sulfur content in baked anode (percent weight). Asha = Ash content in baked anode (percent weight). 44/12 = Ratio of molecular weights...

40 CFR 98.63 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... emissions from anode consumption during electrolysis and anode baking of prebake cells using either the.../metric tons Al). MP = Annual metal production (metric tons Al). Sa = Sulfur content in baked anode (percent weight). Asha = Ash content in baked anode (percent weight). 44/12 = Ratio of molecular weights...

40 CFR 98.63 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... emissions from anode consumption during electrolysis and anode baking of prebake cells using either the.../metric tons Al). MP = Annual metal production (metric tons Al). Sa = Sulfur content in baked anode (percent weight). Asha = Ash content in baked anode (percent weight). 44/12 = Ratio of molecular weights...

Effect of soaking in water and rumen digeta solutions on metabolizable energy content and chemical composition of barley seeds for use in poultry diet.

PubMed

Tabatabee, S N; Sadeghi, G H; Tabeidian, S A

2007-03-15

An experiment was carried out to evaluate the effect of soaking in water and different rumen digesta solutions on nutritional value of dry barley seeds. Treatments were included distilled water as control and rumen digesta that diluted with distilled water to obtain 20, 40 and 60% digesta solutions. Solutions have added to 10 kg of barley seed samples to achieve final 30% moisture content. After 21 days the chemical composition and energy content of barley seed were determined. Gross energy of barley seeds did not affected by different experimental treatments. Use of 20% rumen digesta solution resulted to a significant (p<0.01) increase in AME and AMEn content of barley seeds. Barley seed that treated with 40% of rumen digesta solution had highest TME and TMEn content and its different from seeds that treated with 60 and 100% rumen digesta solutions was significant (p<0.05). The chemical composition such as dry matter, crud protein, crude fat, crud fiber, ash and NFE were found to be similar and there was no significant difference. However, soaking in rumen digesta solutions increased crud protein, ether extract, crude fiber and ash content of barley seeds numerically.

Mechanical and Durability Properties of Fly Ash Based Concrete Exposed to Marine Environment

NASA Astrophysics Data System (ADS)

Kagadgar, Sarfaraz Ahmed; Saha, Suman; Rajasekaran, C.

2017-06-01

Efforts over the past few years for improving the performance of concrete suggest that cement replacement with mineral admixtures can enhance the strength and durability of concrete. Feasibility of producing good quality concrete by using alccofine and fly ash replacements is investigated and also the potential benefits from their incorporation were looked into. In this study, an attempt has been made to assess the performance of concrete in severe marine conditions exposed upto a period of 150 days. This work investigates the influence of alccofine and fly ash as partial replacement of cement in various percentages (Alccofine - 5% replacement to cement content) and (fly ash - 0%, 15%, 30%, 50% & 60% to total cementitious content) on mechanical and durability properties (Permit ion permeability test and corrosion current density) of concrete. Usage of alccofine and high quantity of fly ash as additional cementitious materials in concrete has resulted in higher workability of concrete. Inclusion of alccofine shows an early strength gaining property whereas fly ash results in gaining strength at later stage. Concrete mixes containing 5% alccofine with 15% fly ash replacement reported greater compressive strength than the other concrete mixes cured in both curing conditions. Durability test conducted at 56 and 150 days indicated that concrete containing higher percentages of fly ash resulted in lower permeability as well lesser corrosion density.

Proximate content of wild and cultured eel (Anguilla bicolor) in different part of body

NASA Astrophysics Data System (ADS)

Wijayanti, I.; Susilo, E. S.

2018-02-01

Proximate content in fish varies depends on intrinsic and extrinsic factors. Intrinsic factors include species, sexual maturity, size and body parts. Extrinsic factors include habitat, season and type of food (diet). This study aimed to know the effect of fish body parts (intrinsic factor) on proximate levels in wild and cultured eel (extrinsic). The experimental design used factorial completely randomized design with two factors 2x3. The first factor is the habitat of eel (wild and cultured) and the second factor is the part of the body (head, body and tail) with five replications. The result of statistical analysis showed that there was interaction between fish habitat and body part on moisture, protein, ash and carbohydrate content (P <0.05), but no interaction on fat content and energy (P> 0.05). The highest water content (67.02%) was found in head of wild and the lowest one (59.44%) in the tail of wild eel; The highest protein content (18.09%) was found in the body of cultured eel and the lowest one (15.72%) was in the body of wild eel; The highest ash content (3.73%) was the head of wild eel and the lowest (1.32%) was in the body of cultured eel; The highest carbohydrate (3.73%) was found in the head of cultured eel and the lowest one (0.16%) was in the body of cultured. The wild eel had higher fat content and energy than cultured one, while the fat content and energy in body and tail were higher than in head.

Identification of potential concerns associated with FDOT use of ammoniated coal fly ash.

DOT National Transportation Integrated Search

2012-12-01

The objectives of this project include a careful examination of the issues surrounding high ammonia content in cement due to the use of ammoniated fly ash. The researchers will gather information from published material and consider policies and prac...

Belite cement clinker from coal fly ash of high Ca content. Optimization of synthesis parameters.

PubMed

Guerrero, A; Goñi, S; Campillo, I; Moragues, A

2004-06-01

The optimization of parameters of synthesis of belite cement clinker from coal fly ash of high Ca content is presented in this paper. The synthesis process is based on the hydrothermal-calcination-route of the fly ash without extra additions. The hydrothermal treatment was carried out in demineralized water and a 1 M NaOH solution for 4 h at the temperatures of 100 degrees C, 150 degrees C, and 200 degrees C. The precursors obtained during the hydrothermal treatmentwere heated at temperatures of 700 degrees C, 800 degrees C, 900 degrees C, and 1000 degrees C. The changes of fly ash composition after the different treatments were characterized by X-ray diffraction (XRD), FT infrared (FTIR) spectroscopy, surface area (BET-N2), and thermal analyses. From the results obtained we concluded that the optimum temperature of the hydrothermal treatment was 200 degrees C, and the optimum temperature for obtaining the belite cement clinker was 800 degrees C.

Flexural Toughness of Steel Fiber Reinforced High Performance Concrete Containing Nano-SiO2 and Fly Ash

PubMed Central

Zhao, Ya-Nan; Li, Qing-Fu; Wang, Peng; Zhang, Tian-Hang

2014-01-01

This paper aims to clarify the effect of steel fiber on the flexural toughness of the high performance concrete containing fly ash and nano-SiO2. The flexural toughness was evaluated by two methods, which are based on ASTM C1018 and DBV-1998, respectively. By means of three-point bending method, the flexural toughness indices, variation coefficients of bearing capacity, deformation energy, and equivalent flexural strength of the specimen were measured, respectively, and the relational curves between the vertical load and the midspan deflection (P V-δ) were obtained. The results indicate that steel fiber has great effect on the flexural toughness parameters and relational curves (P V-δ) of the three-point bending beam specimen. When the content of steel fiber increases from 0.5% to 2%, the flexural toughness parameters increase gradually and the curves are becoming plumper and plumper with the increase of steel fiber content, respectively. However these flexural toughness parameters begin to decrease and the curves become thinner and thinner after the steel fiber content exceeds 2%. It seems that the contribution of steel fiber to the improvement of flexural toughness of the high performance concrete containing fly ash and nano-SiO2 is well performed only when the steel fiber content is less than 2%. PMID:24883395

[Effects of sulphur compounds on the volatile characteristics of heavy metals in fly ash from the MSW and sewage sludge co-combustion plant during the disposal process with higher temperature].

PubMed

Liu, Jing-Yong; Sun, Shui-Yu

2012-11-01

Fly ash sample was collected from a MSW co-combustion with sewage sludge plant and the volatilization of heavy metals Pb, Cd, Cu and Zn was investigated before and after the water washing of fly ash, meanwhile, the influence of adding different sulphur compounds (S, NaS, Na2 SO3, Na2 SO4) on the volatilization of heavy metals was studied. The results showed that the contents of Zn, Pb and Mn were high, the Ni content was low and the Cd content reached 29.4 mg x kg(1). The contents of Pb, Cu, Zn increased, while that of Cd reduced in the fly ash after water washing. TG-DTG curves of fly ash showed highest weight loss in ranges of 579-732 degrees C and 949-1 200 degrees C, with 690 degrees C and 1 154 degrees C as the inflection point temperatures. The volatilization of different heavy metals showed great difference in the volatilization rate, following the order of Pb > Cd > Zn > Cu, in which the volatilization rate of Pb was more than 80% and that of Cu was less than 30%. After water washing, the volatilization of different heavy metals showed great difference in the volatilization rate, with the order of Zn > Pb > Cd > Cu, in which the volatilization rate of Zn was more than 20%. With the pretreatment of adding Na2 SO3 and Na2 SO4, the evaporation rates of heavy metals (Cu, Pb, Zn, Cd) were significantly decreased. After adding S, the evaporation rate of Zn was reduced, whereas the addition of Na2S reduced the evaporation rates of Cd and Zn. The evaporation rates of the four heavy metals were all reduced after adding Na2S in the washed fly ash. The evaporation rates of Cu and Zn were reduced with addition of S and Na2SO3 and the evaporation rate of Cd was reduced by adding the four sulfides. The results can provide a basis for the harmless disposal and maximized resource utilization and recycling of fly ash.

Effects of application of mill-generated primary sludge and boiler ash on loblolly pine survival and growth

Treesearch

Emily J. Goodwin; Andrew M. Burrow

2006-01-01

Use of Kraft primary sludge and boiler ash in forest production systems holds promise as a cost-effective alternative to landfilling. From a soil quality perspective, particularly in coarse-textured sandy soils, increases in organic matter content from inputs of sludge/ash may improve soil chemical, biological, and physical properties. The objective of this study was...

Characterization of Residential Scale Biofuel Boilers and Fuels

NASA Astrophysics Data System (ADS)

Chandrasekaran, Sriraam R.

The objectives of this study were to: 1) characterize commercially available wood pellets and wood chips for basic properties such as calorific, ash, moisture contents; 2) analyze elements and ions and other possible contamination during the pellet manufacturing processes; 3) characterize the chemical and thermo-chemical property of grass pellets for their combustion potential; 4) characterize the emissions from 6 different residential scale boiler/furnace appliances burning grass and wood pellets; 5) characterize the emitted particulate matter for toxic and marker species with respect to combustion appliance and combustion conditions; and 6) determine the effects of the biomass fuel properties of 5 different grass pellets on particulate and gaseous emissions from a single type of boiler. The results from characterization of wood pellets and chips indicated that the wood pellet samples generally meet the quality standards. However, there are some samples that would fail the ash content requirements. Only the German standards have extensive trace element limits. Most of the samples would meet these standards, but some samples failed to meet these standards based on their lead, arsenic, cadmium, and copper concentrations. It is likely that inclusion of extraneous materials such as painted or pressure treated lumber led to the observed high concentrations. Given increasing use of pellets and chips as a renewable fuel, standards for the elemental composition of commercial wood pellets and chips are needed in United States to avoid the inclusion of extraneous materials. Such standards would reduce the environmental impact of toxic species that would be released when the wood is burned. Grass pellets were characterized for chemical and thermochemical properties. Switch grass pellets were studied for it thermal degradation process under inert and oxidizing atmosphere using TGA. The thermal degradation of grass pellet measured the activation energy and pre-exponential factors for switch grass decomposition. Two major losses occurred due to volatilization of cellulose, hemicelluloses, and lignin and burning or slow oxidation of residual char. The parameters were high for oxidative environment indicating high temperature sensitivity of the charcoal formation reaction. There was a substantial effect of heating rate on the mass loss and mass loss rate. The TG curve shifted to higher temperature ranges on increasing the heating rate. In both pyrolyzing and oxidizing conditions, average combustion and devolatlization rates increased. Emissions measurements and efficiency estimation were conducted on six commercially available residential scale appliances that utilize different technologies including direct combustion, gasification, lambda control, or fixed air flow rates that were designed to burn low ash wood (less than 1%). The grass has high ash and chlorine content producing more PM and chlorinated hydrocarbons including dioxins and furans. The results also indicated that the air supply and geometry of the furnace, and the type of furnace are also major influencing factors that affect the pollutant formation. To determine the effect of fuel properties on emissions formation, gaseous and particulate characterization was conducted of six fuels that include five different grass pellets types with ash content ranging from 3% to 13% and a premium wood pellet with ash content 0.6% on a boiler. Emissions from grass pellets were found to be higher than wood pellets and the PM; SO2 and NOx emissions were strongly related to the fuel properties such as ash content, sulfur and nitrogen content, respectively. CO emissions that indicate the completeness of reactions were higher for grass pellets and were strongly correlated to PAHs emissions. The PCDD/F emission was clearly a function of chlorine content of the fuel. A strong correlation existed between levoglucosan and PM2.5 concentrations indicated that levoglucosan is also a molecular marker for grass pellet combustion. All of the emissions were found to be higher for grass pellets when compared to the wood pellets and are higher at high loads than at low loads. These results show that the grass pellets cannot be used as a fuel in current generation wood pellet systems. It will be necessary to design systems that effectively deal with the higher ash and chlorine content if grass pellets are to be a significant fuel for home heating. (Abstract shortened by UMI.)

Effect of industrial and domestic ash from biomass combustion, and spent coffee grounds, on soil fertility and plant growth: experiments at field conditions.

PubMed

Ribeiro, João Peres; Vicente, Estela Domingos; Gomes, Ana Paula; Nunes, Maria Isabel; Alves, Célia; Tarelho, Luís A C

2017-06-01

An experimental study was conducted at field conditions in order to evaluate the effect of application of ash from biomass combustion on some soil fertility characteristics and plant growth. Application of 7.5 Mg ha -1 industrial fly ash (IA), domestic ash (DA), and a 50:50 mix of domestic ash (DA) and spent coffee grounds (SCG) was made in different soil parcels. Lolium perenne seeds were sown and the grown biomass was harvested and quantified after 60 days. Soil samples from each parcel were also collected after that period and characterized. Both soil and grown biomass samples were analyzed for Ca, Mg, Na, K, P, Fe, Mn, Zn, and Al contents. Soil pH was determined before and after amendment. All applications rose significantly soil pH. Domestic ash, whether combined with coffee grounds or not, proved to be efficient at supplying available macronutrients Ca, Mg, K, and P to the soil and also reducing availability of Al (more than industrial ash). However, it inhibited plant growth, even more when combined with spent coffee grounds. As regards to elemental abundance in plant tissue, both domestic ash treatments reduced Ca and enhanced Al contents, unlike industrial ash, which proved less harmful for the load applied in the soil. Hence, it was possible to conclude that application load should be a limiting factor for this management option for the studied materials.

Application of Response Surface Methodology to Study the Effects of Brisket Fat, Soy Protein Isolate, and Cornstarch on Nutritional and Textural Properties of Rabbit Sausages.

PubMed

Wambui, Joseph M; Karuri, Edward G; Wanyoike, Margaret M M

2017-01-01

The effects of brisket fat, soy protein isolate, and cornstarch on chemical and textural properties of rabbit sausages were studied using surface response methodology. Sausage samples were prepared using a five-level three-variable Central Composite Rotatable Design with 16 combinations, including two replicates of the center point, carried out in random order. The level of brisket fat (BF), soy protein isolate (SPI), and cornstarch (CS) in the sausage formulation ranged within 8.3-16.7%, 0.7-2.3%, and 1.3-4.7%, respectively. Increasing BF decreased moisture and ash contents but increased protein and fat contents of the sausages ( p < 0.05). Increasing SPI increased moisture content but decreased ash and carbohydrate contents of the sausages ( p < 0.05). Increasing CS increased carbohydrate content ( p < 0.05). Increasing BF increased hardness, adhesiveness, cohesiveness, and chewiness but decreased springiness ( p < 0.05). SPI addition increased springiness but decreased adhesiveness, cohesiveness, and chewiness ( p < 0.05). In conclusion, varying the levels of BF and SPI had a more significant effect on chemical and textural properties of rabbit sausages than CS.

Potency of bio-charcoal briquette from leather cassava tubers and industrial sludge

NASA Astrophysics Data System (ADS)

Citrasari, Nita; Pinatih, Tety A.; Kuncoro, Eko P.; Soegianto, Agoes; Salamun, Irawan, Bambang

2017-06-01

The purpose of this study was to determine the quality of the bio-charcoal briquette with materials from leather cassava tubers and sludge of wastewater treatment plant. The first, bio-charcoal briquette analized stability test and compressive strength. Then, bio-charcoal briquette with best value analyzed for parameter including moisture content, ash content, calorific content, and burned test. The result briquette quality based on compressive strength for bio-charcoal briquettes carbonated water content between 3.8%-4.5% and non-carbonated bio-charcoal briquettes between 5.2%-7.6%. Bio-charcoal carbonation briquette ash content was between 5.30%-7.40% and non-carbonated bio-charcoal briquettes was between 6.86%-7.46%. Bio-charcoal carbonation levels briquettes heated between 578.2 calories/g-1837.7 calories/g and non carbonatedbio-charcoal briquettes between 858.1 calories/g-891.1 calories/g. Carbonated bio-charcoal burned test was between 48-63 minutes and non-carbonated bio-charcoal was between 22-42 minutes. Emissions resulted from the bio-charcoal briquettes for carbonated and non carbonated composition according to the government regulations ESDM No. 047 of 2006 which, at 128 mg/Nm3 and 139 mg/Nm3.

Application of Response Surface Methodology to Study the Effects of Brisket Fat, Soy Protein Isolate, and Cornstarch on Nutritional and Textural Properties of Rabbit Sausages

PubMed Central

Karuri, Edward G.; Wanyoike, Margaret M. M.

2017-01-01

The effects of brisket fat, soy protein isolate, and cornstarch on chemical and textural properties of rabbit sausages were studied using surface response methodology. Sausage samples were prepared using a five-level three-variable Central Composite Rotatable Design with 16 combinations, including two replicates of the center point, carried out in random order. The level of brisket fat (BF), soy protein isolate (SPI), and cornstarch (CS) in the sausage formulation ranged within 8.3–16.7%, 0.7–2.3%, and 1.3–4.7%, respectively. Increasing BF decreased moisture and ash contents but increased protein and fat contents of the sausages (p < 0.05). Increasing SPI increased moisture content but decreased ash and carbohydrate contents of the sausages (p < 0.05). Increasing CS increased carbohydrate content (p < 0.05). Increasing BF increased hardness, adhesiveness, cohesiveness, and chewiness but decreased springiness (p < 0.05). SPI addition increased springiness but decreased adhesiveness, cohesiveness, and chewiness (p < 0.05). In conclusion, varying the levels of BF and SPI had a more significant effect on chemical and textural properties of rabbit sausages than CS. PMID:28706941

Genetic and agronomic assessment of cob traits in corn under low and normal nitrogen management conditions

USDA-ARS?s Scientific Manuscript database

With rising energy demands and costs for fossil fuels, alternative energy from renewable sources such as maize cobs will become competitive. Maize cobs have beneficial characteristics for utilization as feedstock including compact tissue, high cellulose content, and low ash and nitrogen content. Nit...

40 CFR 98.63 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... baking of prebake cells using either the procedures in paragraph (d) of this section or the procedures in.../metric tons Al). MP = Annual metal production (metric tons Al). Sa = Sulfur content in baked anode (percent weight). Asha = Ash content in baked anode (percent weight). 44/12 = Ratio of molecular weights...

Biochar Properties Influencing Greenhouse Gas Emissions in Tropical Soils Differing in Texture and Mineralogy.

PubMed

Butnan, Somchai; Deenik, Jonathan L; Toomsan, Banyong; Antal, Michael J; Vityakon, Patma

2016-09-01

The ability of biochar applications to alter greenhouse gases (GHGs) (CO, CH, and NO) has been attracting research interest. However, inconsistent published results necessitate further exploration of potential influencing factors, including biochar properties, biochar rates, soil textures and mineralogy, and their interactions. Two short-term laboratory incubations were conducted to evaluate the effects of different biochars: a biochar with low ash (2.4%) and high-volatile matter (VM) (35.8%) contents produced under low-temperature (350°C) traditional kiln and a biochar with high ash (3.9%) and low-VM (14.7%) contents produced with a high-temperature (800°C) Flash Carbonization reactor and different biochar rates (0, 2, and 4% w/w) on the GHG emissions in a loamy-sand Ultisol and a silty-clay-loam Oxisol. In the coarse-textured, low-buffer Ultisol, cumulative CO and CH emissions increased with increasing VM content of biochars; however, CO emission sharply decreased at 83 μg VM g soil. In the fine-textured, high-buffer Oxisol, there were significant positive effects of VM content on cumulative CO emission without suppression effects. Regarding cumulative NO emission, there were significant positive effects in the Mn-rich Oxisol. Ash-induced increases in soil pH had negative effects on all studied GHG emissions. Possible mechanisms include the roles biochar VM played as microbial substrates, a source of toxic compounds and complexing agents reducing the toxicity of soil aluminum and manganese, and the role of biochar ash in increasing soil pH affecting GHG emissions in these two contrasting soils. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Reduction of PCDDs/PCDFs in MSWI fly ash using microwave peroxide oxidation in H2SO4/HNO3 solution.

PubMed

Chang, Yu-Min; Dai, Wen-Chien; Tsai, Kao-Shen; Chen, Shiao-Shing; Chen, Jyh-Herng; Kao, Jimmy C M

2013-05-01

Microwave peroxide oxidation (MPO) is an energy-efficient and low GHG emission technology to destroy the hazardous organic compounds in solid waste. The objective of this paper is to explore the reduction feasibility of PCDDs/Fs in MSWI fly ash using the MPO in H2SO4/HNO3 solution. Nearly all PCDDs/Fs, 99% in the original fly ash, can be reduced in 120min at the temperature of 150°C using the MPO treatment. It was also found that a change occurred in the content distribution profiles of 17 major PCDD/F congeners before and after MPO treatment. This provides the potential to reduce the actual PCDDs/Fs content more than I-TEQ contents of PCDDs/Fs. The percentile distribution profile has a tendency of higher chlorinated PCDDs/Fs moving to the lower ones. It concludes that a significant reduction efficiency of I-TEQ toxicity was achieved and showed sufficient reduction of toxic level to lower than 1.0ngI-TEQ(gdw)(-1). The treatment temperature would be a critical factor facilitating the dissolution because higher temperature leads more inorganic salt (parts of fly ash) dissolution. Some problems caused by the MPO method are also delineated in this paper. Copyright © 2013 Elsevier Ltd. All rights reserved.

From fly ash waste slurry to functional adsorbent for valuable rare earth ion separation: An ingenious combination process involving modification, dewatering and grafting.

PubMed

Zhou, Qi; Luo, Tiantian; Yang, Heng; Liang, Cheng; Jing, Luru; Luo, Wenjun

2018-03-01

Acid extracting aluminum from fly ash would produce pestilent secondary fly ash slurry with strong acidity, high content of Cl - and residual Al 3+ that is difficult to be further used. In order to achieve the zero emission, a potential integrated treatment process for reutilization was proposed in this paper. By intelligent use of residual Al 3+ in sludge as catalyst, hydrophobic modification of solid particle was taken with fatty acid via a heterogeneous esterification at normal temperature. Due to the solvophobic force, moisture content of its filter cake was 36.46%, which reduced 11.14% compared with the unmodified one, hydrophobicity scale can achieve 100% with modifier accounting for only 0.8% of solid content and the Cl - concentrations decreased from 20 to 0.102 g/L in wash liquor, thus greatly saving water for washing and energy for drying. Subsequently, based on the appearance of hydrocarbon chains on particle surface, a high-efficiency ultraviolet-induced grafting polymerization was implemented to fabricate density polyacrylic acid decorated fly ash particles from the surface "CH" sites, the resultant composite was proved to efficiently separate valuable rare-earth Gd 3+ from wastewater with outstanding adsorption and regeneration performance, hence bringing high added-value utilization for these hazardous waste. Copyright © 2017 Elsevier Inc. All rights reserved.

Man-made vitreous fiber produced from incinerator ash using the thermal plasma technique and application as reinforcement in concrete.

PubMed

Yang, Sheng-Fu; Wang, To-Mai; Lee, Wen-Cheng; Sun, Kin-Seng; Tzeng, Chin-Ching

2010-10-15

This study proposes using thermal plasma technology to treat municipal solid waste incinerator ashes. A feasible fiberization method was developed and applied to produce man-made vitreous fiber (MMVF) from plasma vitrified slag. MMVF were obtained through directly blending the oxide melt stream with high velocity compressed air. The basic technological characteristics of MMVF, including morphology, diameter, shot content, length and chemical resistance, are described in this work. Laboratory experiments were conducted on the fiber-reinforced concrete. The effects of fibrous content on compressive strength and flexural strength are presented. The experimental results showed the proper additive of MMVF in concrete can enhance its mechanical properties. MMVF products produced from incinerator ashes treated with the thermal plasma technique have great potential for reinforcement in concrete. 2010 Elsevier B.V. All rights reserved.

Study of PCDD/Fs distribution in fly ash, ash deposits, and bottom ash from a medical waste incinerator in China.

PubMed

Du, Yingzhe; Jin, Yuqi; Lu, Shengyong; Peng, Zheng; Li, Xiaodong; Yan, Jianhua

2013-02-01

Over the past decades in China, the number of medical waste incinerators (MWIs) has been rising rapidly, causing emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). In this study, samples of fly ash, ash deposits, and bottom ash from typical MWIs were analyzed for PCDD/Fs and their distribution characteristics. Results showed international toxic equivalent (I-TEQ) values in the range of 6.9-67 ng I-TEQ/g in fly ash and ash deposits, whereas the concentration in bottom ash was extremely low (only 1.33 pg I-TEQ/g), yet the generation of PCDD/Fs was mostly de novo synthesis in fly ash and ash deposits according to the ratio of PCDFs to PCDDs; the major distribution differences of PCDD/Fs in fly ash was manifested by the content of toxic furan 2,3,7,8-TCDF but other toxic PCDD/Fs showed similar distribution. Other findings are that 2,3,4,7,8-PeCDF had the most contribution to TEQ concentration, and that the most abundant toxic furan congener is 1,2,3,4,6,7,8-HpCDF. Correlation analysis showed that there was no significant correlation between PCDD/Fs concentration and several other physical and chemical parameters. This paper is of interest because it presents the emission performances of PCDD/Fs in ash from medical waste incineration in China. PCDD/F contents in fly ash and ash deposits vary between 6.9 and 67.3 ng I-TEQ/g. However, the concentration in bottom ash was extremely low (only 1.33 x 10(-3) ng I-TEQ/g). The fingerprints of PCDD/Fs in fly ash are almost similar, except for 2,3,7,8-TCDF. There is no marked correlation between PCDD/Fs and other physicochemical properties.

Recycling of Sustainable Co-Firing Fly Ashes as an Alkali Activator for GGBS in Blended Cements

PubMed Central

Wu, Yann-Hwang; Huang, Ran; Tsai, Chia-Jung; Lin, Wei-Ting

2015-01-01

This study investigates the feasibility of co-firing fly ashes from different boilers, circulating fluidized beds (CFB) or stokers as a sustainable material in alkali activators for ground granulated blast-furnace slag (GGBS). The mixture ratio of GGBS and co-firing fly ashes is 1:1 by weight. The results indicate that only CF fly ash of CFB boilers can effectively stimulate the potential characteristics of GGBS and provide strength as an alkali activator. CF fly ash consists of CaO3 (48.5%), SiO2 (21.1%), Al2O3 (13.8%), SO3 (10.06%), Fe2O3 (2.25%) and others (4.29%). SA fly ash consists of Al2O3 (19.7%), SiO2 (36.3%), Fe2O3 (28.4%) and others (15.6%). SB fly ash consists of Al2O3 (15%), SiO2 (25.4%), Zn (20.6%), SO3 (10.9%), Fe2O3 (8.78%) and others (19.32%). The mixtures of SA fly ash and SB fly ash with GGBS, respectively, were damaged in the compressive strength test during seven days of curing. However, the built up strength of the CF fly ash and GGBS mixture can only be maintained for 7–14 days, and the compressive strength achieves 70% of that of a controlled group (cement in hardening cement paste). The strength of blended CF fly ash and GGBS started to decrease after 28 days, and the phenomenon of ettrigite was investigated due to the high levels of sulfur content. The CaO content in sustainable co-firing fly ashes must be higher than a certain percentage in reacting GGBS to ensure the strength of blended cements. PMID:28787970

Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan Cao; Quan-Hai Wang; Jun Li

2009-04-15

Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gasmore » inside the reactor was about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155{sup o}C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155{sup o}C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, at testing conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBR addition alone). 25 refs., 5 figs., 1 tab.« less

The utilization of microbes as a fermentation agent to reduce saponin in Trembesi leaves (Sammanea saman)

NASA Astrophysics Data System (ADS)

Sariri, A. K.; Mulyono, A. M. W.; Tari, A. I. N.

2018-03-01

This objective of this research was to observe the utilization of microbes as a fermentation agent of trembesi leaves that can increase the quality of trembesi leaves as ruminants feed. Before fermentation, trembesi leaves were divided into three treatments. They were control = non-agentic in fermentation, D-An = the addition of Aspergillus niger as fermentation agent, and D-Lp = the addition of Lactobacillus plantarum as fermentation agent. Each treatment experienced five repetitions. The experimental design used a randomized direct pattern group design. The analysis included proximate analysis consisting of water content, crude protein content, crude fiber content, lipid content, mineral content (ash) and saponin content after fermentation. It could be concluded that the utilization of Aspergillus niger and Lactobacillus plantarum in fermentation could decrease saponin content and could increase the nutrient content of trembesi leaves by increasing crude protein content otherwise by decreasing crude fiber content of trembesi leaves.

Hydrologic conditions controlling runoff generation immediately after wildfire

USGS Publications Warehouse

Ebel, Brian A.; Moody, John A.; Martin, Deborah A.

2012-01-01

We investigated the control of postwildfire runoff by physical and hydraulic properties of soil, hydrologic states, and an ash layer immediately following wildfire. The field site is within the area burned by the 2010 Fourmile Canyon Fire in Colorado, USA. Physical and hydraulic property characterization included ash thickness, particle size distribution, hydraulic conductivity, and soil water retention curves. Soil water content and matric potential were measured indirectly at several depths below the soil surface to document hydrologic states underneath the ash layer in the unsaturated zone, whereas precipitation and surface runoff were measured directly. Measurements of soil water content showed that almost no water infiltrated below the ash layer into the near-surface soil in the burned site at the storm time scale (i.e., minutes to hours). Runoff generation processes were controlled by and highly sensitive to ash thickness and ash hydraulic properties. The ash layer stored from 97% to 99% of rainfall, which was critical for reducing runoff amounts. The hydrologic response to two rain storms with different rainfall amounts, rainfall intensity, and durations, only ten days apart, indicated that runoff generation was predominantly by the saturation-excess mechanism perched at the ash-soil interface during the first storm and predominantly by the infiltration-excess mechanism at the ash surface during the second storm. Contributing area was not static for the two storms and was 4% (saturation excess) to 68% (infiltration excess) of the catchment area. Our results showed the importance of including hydrologic conditions and hydraulic properties of the ash layer in postwildfire runoff generation models.

Hydrodesulfurization and hydrodenitrogenation catalysts obtained from coal mineral matter

DOEpatents

Liu, Kindtoken H. D.; Hamrin, Jr., Charles E.

1982-01-01

A hydrotreating catalyst is prepared from coal mineral matter obtained by low temperature ashing coals of relatively low bassanite content by the steps of: (a) depositing on the low temperature ash 0.25-3 grams of an iron or nickel salt in water per gram of ash and drying a resulting slurry; (b) crushing and sizing a resulting solid; and (c) heating the thus-sized solid powder in hydrogen.

Porosity of Self-Compacting Concrete (SCC) incorporating high volume fly ash

NASA Astrophysics Data System (ADS)

Kristiawan, S. A.; Sunarmasto; Murti, G. Y.

2017-02-01

Degradation of concrete could be triggered by the presence of aggressive agents from the environment into the body of concrete. The penetration of these agents is influenced by the pore characteristics of the concrete. Incorporating a pozzolanic material such as fly ash could modify the pore characteristic of the concrete. This research aims to investigate the influence of incorporating fly ash at high volume level on the porosity of Self-Compacting Concrete (SCC). Laboratory investigations were carried out following the ASTM C642 for measuring density and volume of permeable pores (voids) of the SCC with varying fly ash contents (50-70% by weight of total binder). In addition, a measurement of permeable voids by saturation method was carried out to obtain an additional volume of voids that could not be measured by the immersion and boiling method of ASTM C642. The results show that the influence of fly ash content on the porosity appears to be dependent on age of SCC. At age less than 56 d, fly ash tends to cause an increase of voids but at 90 d of age it reduces the pores. The additional pores that can be penetrated by vacuum saturation method counts about 50% of the total voids.

Comparative Physicochemical Evaluation of Kharekhasak (Tribulus terrestris Linn.) Before and After Mudabbar Process

PubMed Central

Tauheed, Abdullah; Hamiduddin; Khanam, Salma; Ali, Mohd Akhtar; Zaigham, Mohammad

2017-01-01

Background and Objectives: Mudabbar/Tadbeere advia is referred to the processes performed on the drugs to detoxify, purify, and enhance therapeutic action and to reduce its doses before making the formulations in Unani medicine. It improves quality of drugs either by optimizing its desirable characteristics or minimizing the undesirable ones; it makes drug effective, safe, and specific. There is a need of comparative evaluation to understand its significance. Tadbeer of Kharekhasak (KK) khurd (Tribulus terrestris Linn. fruit) is described by Rabban Al-Tabari in Firdausul Hikmat, Akbar Arzani in Qarabadeene Qadri, etc., during the compounding of aphrodisiac formulations. Mudabbar Kharekhasak (MKK) used in Safoofe Kharekhasak mentioned in Al-Qarabadeene was evaluated in this work. Methods: Mudabbar/Tadbeer process was carried out by blending fresh KK. Juice with powdered dry KK and drying it under the sun. Juice used for process is thrice the weight of dry KK powder. The KK before and after the process was evaluated using physicochemical tests: powder characterization, extractive value, alcohol and water soluble matter, ash value, loss on drying (LOD) at 105°C, pH, high-performance thin layer chromatography (HPTLC) fingerprinting, and diosgenin content. Results: Powder characterizations were set in. Increase in successive and nonsuccessive extractive values in various solvents, water/alcohol-soluble content, total ash, acid-insoluble ash, water-soluble ash, and sulfated ash of MKK was noted in comparison with KK. Decrease in LOD at 105°C and pH of MKK powder was observed. HPTLC fingerprinting data were developed for the identification and evaluation. Quantification of diosgenin content increased to 432.1 g/g in MKK as compared to 144.5 g/g in KK, suggesting significant increase in saponin content. Conclusion: Data obtained clearly indicated changes in MKK validating the classical Mudabbar process, probably to enhance/modify the action of drug. Standards for crude and MKK were established for future reference. SUMMARY Mudabbar process on Tribulus terrestris Linn (KK) havebeen validated.Physicochemical data for Mudabbar and non mudabbar Kharekhasak (KK) powder have been set in.Diosgenin content was increased significantly in mudabbar KK. Abbreviations Used: KK: Kharekhasak, TT: Tribulus terrestris, MKK: mudabbar Kharekhasak, SK: Safoofe Kharekhasak, LOD: loss of weight on drying, HPTLC: High performance thin layer chromatography, BSS: British standard sieve, μl: microliter, SEM: Standard error of mean, nm: nanometer, g: gram. PMID:29263633

Comparative Physicochemical Evaluation of Kharekhasak (Tribulus terrestris Linn.) Before and After Mudabbar Process.

PubMed

Tauheed, Abdullah; Hamiduddin; Khanam, Salma; Ali, Mohd Akhtar; Zaigham, Mohammad

2017-01-01

Mudabbar/ Tadbeere advia is referred to the processes performed on the drugs to detoxify, purify, and enhance therapeutic action and to reduce its doses before making the formulations in Unani medicine. It improves quality of drugs either by optimizing its desirable characteristics or minimizing the undesirable ones; it makes drug effective, safe, and specific. There is a need of comparative evaluation to understand its significance. Tadbeer of Kharekhasak (KK) khurd ( Tribulus terrestris Linn. fruit) is described by Rabban Al-Tabari in Firdausul Hikmat, Akbar Arzani in Qarabadeene Qadri, etc., during the compounding of aphrodisiac formulations. Mudabbar Kharekhasak (MKK) used in Safoofe Kharekhasak mentioned in Al-Qarabadeene was evaluated in this work. Mudabbar/Tadbeer process was carried out by blending fresh KK. Juice with powdered dry KK and drying it under the sun. Juice used for process is thrice the weight of dry KK powder. The KK before and after the process was evaluated using physicochemical tests: powder characterization, extractive value, alcohol and water soluble matter, ash value, loss on drying (LOD) at 105°C, pH, high-performance thin layer chromatography (HPTLC) fingerprinting, and diosgenin content. Powder characterizations were set in. Increase in successive and nonsuccessive extractive values in various solvents, water/alcohol-soluble content, total ash, acid-insoluble ash, water-soluble ash, and sulfated ash of MKK was noted in comparison with KK. Decrease in LOD at 105°C and pH of MKK powder was observed. HPTLC fingerprinting data were developed for the identification and evaluation. Quantification of diosgenin content increased to 432.1 g/g in MKK as compared to 144.5 g/g in KK, suggesting significant increase in saponin content. Data obtained clearly indicated changes in MKK validating the classical Mudabbar process, probably to enhance/modify the action of drug. Standards for crude and MKK were established for future reference. Mudabbar process on Tribulus terrestris Linn (KK) havebeen validated.Physicochemical data for Mudabbar and non mudabbar Kharekhasak (KK) powder have been set in.Diosgenin content was increased significantly in mudabbar KK. Abbreviations Used: KK: Kharekhasak, TT: Tribulus terrestris , MKK: mudabbar Kharekhasak, SK: Safoofe Kharekhasak , LOD: loss of weight on drying, HPTLC: High performance thin layer chromatography, BSS: British standard sieve, μl: microliter, SEM: Standard error of mean, nm: nanometer, g: gram.

Hydraulic conductivity of fly ash-sewage sludge mixes for use in landfill cover liners.

PubMed

Herrmann, Inga; Svensson, Malin; Ecke, Holger; Kumpiene, Jurate; Maurice, Christian; Andreas, Lale; Lagerkvist, Anders

2009-08-01

Secondary materials could help meeting the increasing demand of landfill cover liner materials. In this study, the effect of compaction energy, water content, ash ratio, freezing, drying and biological activity on the hydraulic conductivity of two fly ash-sewage sludge mixes was investigated using a 2(7-1) fractional factorial design. The aim was to identify the factors that influence hydraulic conductivity, to quantify their effects and to assess how a sufficiently low hydraulic conductivity can be achieved. The factors compaction energy and drying, as well as the factor interactions material x ash ratio and ash ratio x compaction energy affected hydraulic conductivity significantly (alpha=0.05). Freezing on five freeze-thaw cycles did not affect hydraulic conductivity. Water content affected hydraulic conductivity only initially. The hydraulic conductivity data were modelled using multiple linear regression. The derived models were reliable as indicated by R(adjusted)(2) values between 0.75 and 0.86. Independent on the ash ratio and the material, hydraulic conductivity was predicted to be between 1.7 x 10(-11)m s(-1) and 8.9 x 10(-10)m s(-1) if the compaction energy was 2.4 J cm(-3), the ash ratio between 20% and 75% and drying did not occur. Thus, the investigated materials met the limit value for non-hazardous waste landfills of 10(-9)m s(-1).

[Volatile ashes and their biological effect. 2. Fibrogenic effect of volatile ashes].

PubMed

Woźniak, H; Wiecek, E; Lao, I; Wojtczak, J

1989-01-01

In experiments on white Wistar rats fibrogenic effects of 6 samples of fly-ashes collected from electric precipitators in power engineering plants have been evaluated. The coal came from different national deposits. All the ashes have been found to contain: quartz and mullite, 3 ashes contained additionally orthoclase, whereas 1, apart from quartz and mullite, contained kaolinite; naturally radioactive elements (Ra226, K40, Th228) and trace elements (As, Ba, Be, Cd, Ce, Cu, Fe, Pa, Mo, Ni, Pb, Se, U Zu). Experimental pneumoconiosis was induced through intratracheal administration of single doses of 50 mg of dust; the experiment was carried out at 3 time intervals of 3, 6 and 9 months. The fibrogenic activity was evaluated both qualitatively (histopathological methods) and quantitatively (lung weight, hydroxyproline content in lungs, dust elimination from lungs); control groups consisted of animals which obtained NaCl solution and quartz sands. Fly-ashes were found to exhibit different fibrogenic effects, yet, their fibrogenic activity was weaker, compared to quartz sands. No clear correlation was found between fibrogenic effects of ashes and test physico-chemical properties, such as the content of SiO2, trace elements or naturally radioactive elements. Analysis of occupational diseases (for the period section): (1979-1983) demonstrated occupational diseases of dust-related aetiology among power engineering workers, pneumoconioses, constituting 7.8% of 127 cases of occupational diseases.

21 CFR 137.220 - Durum flour.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 1.5 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash, moisture, and granulation are determined by the methods prescribed in § 137.105(c). ...

21 CFR 137.220 - Durum flour.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 1.5 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash, moisture, and granulation are determined by the methods prescribed in § 137.105(c). ...

21 CFR 137.220 - Durum flour.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 1.5 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash, moisture, and granulation are determined by the methods prescribed in § 137.105(c). ...

21 CFR 137.220 - Durum flour.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 1.5 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash, moisture, and granulation are determined by the methods prescribed in § 137.105(c). ...

21 CFR 137.220 - Durum flour.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 1.5 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash, moisture, and granulation are determined by the methods prescribed in § 137.105(c). ...

[Supplementation of wheat flour with chickpea (Cicer arietinum) flour. I. Preparation of flours and their properties for bread making].

PubMed

Figuerola, F E; Estévez, A M; Castillo, E

1987-06-01

The feasibility of adding chick-pea flour substituting part of wheat flour in yeast-leavened bread-making in order to increase the protein value, was studied. A 70% extraction chick-pea flour of commercial granulometry (150 mu) was prepared. Wheat flours of 74% and 78% extraction were then blended with 5%, 10% and 15% of chick-pea flour. Every flour and blend were subsequently analyzed to determine protein, ash, fiber, fat and maltose content, as well as sedimentation, farinogram and bread-making. Addition of chick-pea flour increased protein, fiber, ash and fat content in the blends, not causing a severe effect on quality, even at the 15% level of substitution. Blends showed an increase in maltose content, W value and bread specific volume. Furthermore, breads prepared were of good quality even without the use of maturing agents.

Water, moisture and ash content of mechanically cleaned greige cotton, naturally colored brown cotton, flax and rayon

USDA-ARS?s Scientific Manuscript database

This exploratory research evaluated the Karl Fischer Titration reference method (KFT, ASTM D7785) to accurately measure water content of mechanically cleaned greige cotton, a naturally colored brown cotton, flax and rayon at moisture equilibrium. Each sample was analyzed by KFT, standard oven dryin...

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO2 Contents at 650 °C

NASA Astrophysics Data System (ADS)

Lu, Jintao; Yang, Zhen; Li, Yan; Huang, Jinyang; Zhou, Yongli; Zhao, Xinbao; Yuan, Yong

2018-05-01

The corrosion behaviors of Super304H and HR3C used for USC boiler applications were investigated in simulated coal ash/gas environments with 0.1 and 1.5% of SO2 at 650 °C for 500 h. The results indicated that the increase in SO2 accelerated the corrosion rate and the spalling tendency of the corrosion layer in both tested alloys. Fe2O3, Cr2O3 and FeCr2O4 main peaks were revealed by XRD on Super304H, but on HR3C only the Cr2O3 peak showed a high intensity. The SO2 content did not affect the corrosion product composition of any of the alloys, but accelerated the inner sulfidation and the spallation on Super304H. No obvious internal sulfidation was observed on HR3C in either SO2 content. Based on the experimental results, the alloy corrosion mechanism and the influence of sulfur content on the corrosion process were discussed.

Manufacture of dissolving pulps from cornstalk by novel method coupling steam explosion and mechanical carding fractionation.

PubMed

Wang, Ning; Chen, Hong-Zhang

2013-07-01

In order to solve the inhomogeneity of cornstalk as fiber material to manufacture dissolving pulp, a novel method of steam explosion coupling mechanical carding was put forward to fractionate cornstalk long fiber for the production of cornstalk dissolving pulp. The fractionated long fiber had homogeneous structure and low hemicellulose and ash content. The fiber cell content was up to 85% in area, and the hemicellulose and ash content was 8.34% and 1.10% respectively. The α-cellulose content of cornstalk dissolving pulps was up to 93.10-97.10%, the viscosity was 14.37-23.96 mPas, and the yields of cornstalk dissolving pulps were from 10.11% to 12.44%. In addition, the fractionated short fiber was to be hydrolyzed by enzyme to build sugar platform. The constructed method of steam explosion coupling mechanical carding achieved the fractionation of cornstalk into long fiber and short fiber cleanly and effectively, and provided a new way for cornstalk integrated refinery. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparison of mass balance, energy consumption and cost of composting facilities for different types of organic waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Huijun; Matsuto, Toshihiko, E-mail: matsuto@eng.hokudai.ac.jp

2011-03-15

Mass balance, energy consumption and cost are basic pieces of information necessary for selecting a waste management technology. In this study, composting facilities that treat different types of organic waste were studied by questionnaire survey and via a chemical analysis of material collected at the facilities. The mass balance was calculated on a dry weight basis because the moisture content of organic waste was very high. Even though the ratio of bulking material to total input varied in the range 0-65% on a dry basis, the carbon and ash content, carbon/nitrogen ratio, heavy metal content and inorganic nutrients in themore » compost were clearly influenced by the different characteristics of the input waste. The use of bulking material was not correlated with ash or elemental content in the compost. The operating costs were categorised into two groups. There was some economy of scale for wages and maintenance cost, but the costs for electricity and fuel were proportional to the amount of waste. Differences in operating costs can be explained by differences in the process characteristics.« less

Effects of diet on titratable acid-base excretion in grasshoppers.

PubMed

Frazier, M R; Harrison, J F; Behmer, S T

2000-01-01

Despite the potential for diet to affect organismal acid-base status, especially in herbivores, little is known about the effects of diet on acid-base loading and excretion. We tested the effects of diet on acid-base loading and excretion in grasshoppers by (a) comparing the fecal acid-base content of 15 grasshopper species collected from the field and (b) comparing fecal acid-base excretion rates of Schistocerca americana grasshoppers fed vegetable diets that differed in their ashed and raw acid-base contents. The field experiments indicated that grass-feeding species excrete fairly neutral fecal pellets, while forb/mixed-feeding species vary widely in their fecal acid-base contents. In the laboratory experiment, acid-base excretion rates were positively correlated with dietary ashed base intake rates but were not correlated with the acid-base content of raw, unashed diet or feeding rate. These experiments suggest that some diets could strongly challenge the acid-base homeostasis of herbivores; in some grasshoppers, dietary acid-base loads could produce certainly lethal 1-unit changes in average body pH within 6 h if they were not excreted.

Characterisation of agroindustrial solid residues as biofuels and potential application in thermochemical processes.

PubMed

Virmond, Elaine; De Sena, Rennio F; Albrecht, Waldir; Althoff, Christine A; Moreira, Regina F P M; José, Humberto J

2012-10-01

In the present work, selected agroindustrial solid residues from Brazil - biosolids from meat processing wastewater treatment and mixture of sawdust with these biosolids; residues from apple and orange juice industries; sugarcane bagasse; açaí kernels (Euterpe oleracea) and rice husk - were characterised as solid fuels and an evaluation of their properties, including proximate and ultimate composition, energy content, thermal behaviour, composition and fusibility of the ashes was performed. The lower heating value of the biomasses ranged from 14.31 MJkg(-1) to 29.14 MJkg(-1), on a dry and ash free basis (daf), all presenting high volatile matter content, varying between 70.57 wt.% and 85.36 wt.% (daf) what improves the thermochemical conversion of the solids. The fouling and slagging tendency of the ashes was predicted based on the fuel ash composition and on the ash fusibility correlations proposed in the literature, which is important to the project and operation of biomass conversion systems. The potential for application of the Brazilian agroindustrial solid residues studied as alternative energy sources in thermochemical processes has been identified, especially concerning direct combustion for steam generation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Ash content, carbon and C/N ratio in paricá in function of NPK fertilization.

PubMed

Vieira, Cristiane R; Weber, Oscarlina L S; Scaramuzza, José Fernando

2018-01-01

Fertilization in areas of forest plantations is needed to supplement plants´ nutritional needs until harvest. An experiment was performed to check the influence of fertilization on levels of ash, carbon and C/N relation in Schizolobium amazonicum. Soil liming was performed and fertilization occurred after 15 days of incubation. S. amazonicum seedlings were produced and submitted to fertilization with N, P and K: N = 0, 40, 80 and 120 kg ha-1; P2O5 = 0, 50, 100 and 200 kg ha-1; K2O = 0, 50, 100 and 200 kg ha-1. The plants were measured after 180 days. The seedlings of 20 treatments with the highest increase in height and diameter were transplanted to the field. Soil was fertilized and limestone was spread; seedlings were distributed into randomized blocks, with six replications. After 12 months, the plants were removed to determine ash, organic carbon, C/N relation contents. The ashes were submitted to digestion to determine nutrient concentrations. Fertilization influenced the levels of ash and organic carbon and C/N relation in S. amazonicum. Results indicate that the species has a potential for energy production.

Iron solubility related to particle sulfur content in source emission and ambient fine particles.

PubMed

Oakes, M; Ingall, E D; Lai, B; Shafer, M M; Hays, M D; Liu, Z G; Russell, A G; Weber, R J

2012-06-19

The chemical factors influencing iron solubility (soluble iron/total iron) were investigated in source emission (e.g., biomass burning, coal fly ash, mineral dust, and mobile exhaust) and ambient (Atlanta, GA) fine particles (PM2.5). Chemical properties (speciation and mixing state) of iron-containing particles were characterized using X-ray absorption near edge structure (XANES) spectroscopy and micro-X-ray fluorescence measurements. Bulk iron solubility (soluble iron/total iron) of the samples was quantified by leaching experiments. Major differences were observed in iron solubility in source emission samples, ranging from low solubility (<1%, mineral dust and coal fly ash) up to 75% (mobile exhaust and biomass burning emissions). Differences in iron solubility did not correspond to silicon content or Fe(II) content. However, source emission and ambient samples with high iron solubility corresponded to the sulfur content observed in single particles. A similar correspondence between bulk iron solubility and bulk sulfate content in a series of Atlanta PM2.5 fine particle samples (N = 358) further supported this trend. In addition, results of linear combination fitting experiments show the presence of iron sulfates in several high iron solubility source emission and ambient PM2.5 samples. These results suggest that the sulfate content (related to the presence of iron sulfates and/or acid-processing mechanisms by H(2)SO(4)) of iron-containing particles is an important proxy for iron solubility.

Synergistic dye adsorption by biochar from co-pyrolysis of spent mushroom substrate and Saccharina japonica.

PubMed

Sewu, Divine Damertey; Boakye, Patrick; Jung, Hwansoo; Woo, Seung Han

2017-11-01

The potential of activating terrestrial biomass (spent mushroom substrate, SMS) with ash-laden marine biomass [kelp seaweed, KE] via co-pyrolysis in the field of adsorption was first investigated. KE biochar (KBC), SMS biochar (SMSBC), biochar (SK10BC) from 10%-KE added SMS, and biochar (ESBC) from KE-extract added SMS were used for the adsorption of cationic dye crystal violet (CV). ESBC had highest fixed carbon content (70.60%) and biochar yield (31.6%). SK10BC exhibited high ash content, abundant functional groups, coarser surface morphology and Langmuir maximum adsorptive capacity (610.1mg/g), which is 2.2 times higher than that of SMSBC (282.9mg/g). Biochar activated by a small amount of high ash-containing biomass such as seaweed via co-pyrolysis can serve as viable alternative adsorbent for cationic dye removal. Copyright © 2017 Elsevier Ltd. All rights reserved.

Variations in Compressive Strength of Geopolymer due to the CaO Added Fly Ash

NASA Astrophysics Data System (ADS)

Zhao, Yuqing; Koumoto, Tatsuya; Kondo, Fumiyoshi

Recently, geopolymer has been a noteworthy material which can be used as a replacement for portland cement. The mechanical characteristics and consistency of the geopolymer are strongly affected by its chemical components of fly ash. The variations in compressive strength of geopolymer due to the CaO added fly ash were investigated in this paper. The compressive strengths of geopolymer were increased with an increase in the curing period, and the characteristics changed from the one of plastic soil material to brittle material such as concrete, regardless of CaO content. Also, the results of compressive strength and modulus of deformation showed their maximum value in the case of 8-10% CaO content. From this result, the maximum characteristics of the strengths were assumed to be exerted in case which the water draining process of geopolymer was balanced with the water absorbing process of additional CaO.

Finite element beam flexural properties of cement composites of fiber reinforced PVA

NASA Astrophysics Data System (ADS)

Yang, Chengzhi; Pei, Changchun

2018-05-01

In this paper, the initial cracking state and the mid span bending moment and deflection of ECC beam under different PVA fiber and fly ash mixing rate are studied by finite element simulation analysis. The results show that the bending moment of the ECC beam increases with the increase of the PVA fiber content, and the deflection decreases. When the ratio of PVA fiber is 1.5%, the middle bending moment is the largest and the deflection is the least. With the increase of fly ash content, the mid span bending moment of ECC beam increases first and then decreases. When the fly ash ratio is 60%, the middle bending moment is the largest and the deflection is the least. Through the study, the formula for calculating the flexural capacity of the cross section suitable for ECC beams is derived.

Effect of low level of dietary aflatoxins on baladi rabbits.

PubMed

Abdelhamid, A M; el-Shawaf, I; el-Ayoty, S A; Ali, M M; Gamil, T

1990-01-01

Aflatoxins B1, B2, G1 & G2 were administered in a low concentration (100 ppb of each aflatoxin (AN] in a mash offered to Baladi rabbits. An other group of rabbits were fed on the same contaminated mash in addition to 0.25% charcoal (CC). The two groups were compared to control animals fed on AN-free mash. Inclusion of AN in the diet decreased feed and water consumption, body weight and survival rate. Charcoal improved somewhat feed and water consumption and growth rate than AN-group. However, CC-group affected digestibility of organic matter more than AN-group. Relative weights of liver, kidneys, heart and adrenal glands were significantly higher in AN and CC groups than the control group. Blood haemoglobin content, packed cell volume percentage and sedimentation rate were lower in AN group. Although there were an increase in each of serum, calcium, inorganic phosphorus, cholesterol, phospholipids and glutamic-pyruvic transaminase in AN group, yet the serum nitrogen and glutamic-oxalacetic transaminase were reduced. Charcoal had alleviated AN-effects concerning N, GPT and phospholipids. Chemical analysis revealed elevation of water, ash and silica contents of liver and water content of muscles from AN-animals. On the other hand, fat content, GOT and vitamin A in the liver as well as muscles ash were reduced. Addition of CC to the diet reduced AN-effects on liver fat, ash and silica but resulted in a rise of the water content of liver and muscles and liver GPT activity. Charcoal also resulted in a sharp decrease in vitamin A content of the liver. Aflatoxin treatments (in AN and CC groups) reduced bone ash, silica and magnesium as well as bone volume. Charcoal administration increased Ca-content of bones. Aflatoxin feeding (in AN group) resulted in a high residual percentage of AN in muscles, serum, liver, heart and kidneys with relationships of 51 :24 : 3 :2 : 1, respectively. Only 1.42% of the fed AN was excreted in the faeces. Charcoal usage had a good effect as it prevented AN to accumulate in the organs. Aflatoxin contaminated diets (in AN and CC groups) resulted in paralysis, disorder of fat deposition, discolouration and haemorrhages of some organs. Scanning electron microscopic examination revealed no ill effect on the surface structure of the small intestine due to either AN or AN + CC. Pathological examination showed that the main affected organs were liver, heart and spleen, respectively. The changes include hepatic round cell infiltration, irregularities of lobular plats, focal necrosis and periportal fibrosis.(ABSTRACT TRUNCATED AT 400 WORDS)

Chemical and physical properties of two-year short-rotation deciduous species. [Olea sp. , Populus deltoides, Platanus sp. , Alnus glutinosa, Paulownia tomentosa, Robina pseudoacacia, Acer saccharinum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C.S

1982-01-01

The following seven broadleaved species were tested: autumn olive (Olea sp.) eastern cottonwood (Populus deltoides), sycamore (Platanus species), black alder (Alnus glutinosa), royal paulownia (Paulownia tomentosa), black locust (Robina pseudoacacia) and silver maple (Acer saccharinum). The species and portions both significantly affected the chemical and the physical findings of the juvenile wood. The ages, which were tested in factorial combination with the species, also showed a significant effect on both the chemical and the physical properties of wood. All of the results indicated that both chemical and physical properties did vary with species, among the portions of the wood, andmore » according to the ages of the wood. From the portion standpoint, the bark had higher gross heat content, sulphur content, ash content and lignin content, and it was also higher in all three kinds of extractives contents. The wood portion was found to be rich in holocellulose, alpha-cellulose and pentosan. In considering the chemical and physical properties of juvenile wood among the species, eastern cottonwood was found to have the highest value for ash content and all of the three kinds of extractives content. Paulownia had the highest value for sulphur content. Black locust had highest gross heat content, holocellulose and alpha-cellulose contents. Silver maple had highest lignin content. Results from this study showed that these seven juvenile hardwood species can produce high biomass yields of fibre and energy when grown under intensive care in central and southern Illinois sites. The best species of these seven tested woods seem to be black locust, which could also serve as a raw material for the pulp and paper industry, as well as for a fuel for energy generation. However, further economic and energy efficiency analyses are needed before judging the feasibility of these short-rotation juvenile hardwood species.« less

Organic petrology of Paleocene Marcelina Formation coals, Paso Diablo mine, western Venezuela: Tectonic controls on coal type

USGS Publications Warehouse

Hackley, P.C.; Martinez, M.

2007-01-01

About 7??Mt of high volatile bituminous coal are produced annually from the four coal zones of the Upper Paleocene Marcelina Formation at the Paso Diablo open-pit mine of western Venezuela. As part of an ongoing coal quality study, we have characterized twenty-two coal channel samples from the mine using organic petrology techniques. Samples also were analyzed for proximate-ultimate parameters, forms of sulfur, free swelling index, ash fusion temperatures, and calorific value. Six of the samples represent incremental benches across the 12-13??m thick No. 4 bed, the stratigraphically lowest mined coal, which is also mined at the 10??km distant Mina Norte open-pit. Organic content of the No. 4 bed indicates an upward increase of woody vegetation and/or greater preservation of organic material throughout the life of the original mire(s). An upward increase in telovitrinite and corresponding decrease in detrovitrinite and inertinite illustrate this trend. In contrast, stratigraphically higher coal groups generally exhibit a 'dulling upward' trend. The generally high inertinite content, and low ash yield and sulfur content, suggest that the Paso Diablo coals were deposited in rain-fed raised mires, protected from clastic input and subjected to frequent oxidation and/or moisture stress. However, the two thinnest coal beds (both 0.7??m thick) are each characterized by lower inertinite and higher telovitrinite content relative to the rest of Paso Diablo coal beds, indicative of less well-established raised mire environments prior to drowning. Foreland basin Paleocene coals of western Venezuela, including the Paso Diablo deposit and time-correlative coal deposits of the Ta??chira and Me??rida Andes, are characterized by high inertinite and consistently lower ash and sulfur relative to Eocene and younger coals of the area. We interpret these age-delimited coal quality characteristics to be due to water availability as a function of the tectonic control of subsidence rate. It is postulated that slower subsidence rates dominated during the Paleocene while greater foreland basin subsidence rates during the Eocene-Miocene resulted from the loading of nappe thrust sheets as part of the main construction phases of the Andean orogen. South-southeastward advance and emplacement of the Lara nappes during the oblique transpressive collision of the Caribbean and South American tectonic plates in the Paleocene was further removed from the sites of peat deposition, resulting in slower subsidence rates. Slower subsidence in the Paleocene may have favored the growth of raised mires, generating higher inertinite concentrations through more frequent moisture stress. Consistently low ash yield and sulfur content would be due to the protection from clastic input in raised mires, in addition to the leaching of mineral matter by rainfall and the development of acidic conditions preventing fixation of sulfur. In contrast, peat mires of Eocene-Miocene age encountered rapid subsidence due to the proximity of nappe emplacement, resulting in lower inertinite content, higher and more variable sulfur content, and higher ash yield.

[Effects of different drying methods on processing performance and quality in bulbus of Tulipa edulis].

PubMed

Yang, Xiao-hua; Guo, Qiao-sheng; Zhu, Zai-biao; Chen, Jun; Miao, Yuan-yuan; Yang, Ying; Sun, Yuan

2015-10-01

Effects of different drying methods including sun drying, steamed, boiled, constant temperature drying (at 40, 50, 60 °C) on appearance, hardness, rehydration ratio, dry rate, moisture, total ash, extractive and polysaccharides contents were studied to provide the basis of standard processing method for Tulipa edulis bulbus. The results showed that the treatments of sun drying and 40 °C drying showed higher rehydration ratios, but lower dry rate, higher hardness, worse color, longer time and obvious distortion and shrinkage in comparison with other drying methods. The treatments of 60 °C constant temperature drying resulted in shorter drying time, lower water and higher polysaccharides content. Drying time is shorter and appearance quality is better in the treatment of steaming and boiling compared with other treatments, but the content of extractive and polysaccharides decreased significantly. The treatments of 50 °C constant temperature drying led to similar appearance quality of bulb to commercial bulb, and it resulted in lowest hardness and highest dry rate as well as higher rehydration ratio, extractive and polysaccharides content, moderate moisture and total ash contents among these treatments. Based on the results obtained, 50 °C constant temperature drying is the better way for the processing of T. edulis bulbus.

Proximate biochemical composition and caloric content calculated from elemental CHN analysis: a stoichiometric concept.

PubMed

Gnaiger, E; Bitterlich, G

1984-06-01

Carbohydrate, lipid, and protein compositions are stoichiometrically related to organic CHN (carbon, hydrogen, nitrogen) contents. Elemental CHN analyses of total biomass and ash, therefore, provide a basis for the calculation of proximate biochemical composition and bomb caloric value. The classical nitrogen to protein conversion factor (6.25) should be replaced by 5.8±0.13. A linear relation exists between the mass fraction of non-protein carbon and the carbohydrate and lipid content. Residual water in dry organic matter can be estimated with the additional information derived from hydrogen measurements.The stoichiometric CHN method and direct biochemical analysis agreed within 10% of ash-free dry biomass (for muscle, liver and fat tissue of silver carp; gut contents composed of detritus and algae; commercial fish food). The detrital material, however, had to be corrected for non-protein nitrogen.A linear relationship between bomb caloric value and organic carbon fractions was derived on the basis of thermodynamic and stoichiometric principles, in agreement with experimental data published for bacteria, algae, protozoa and invertebrates. The highly automatic stoichiometric CHN method for the separation of nutrient contents in biomass extends existing ecophysiological concepts for the construction of balanced carbon and nitrogen, as well as biochemical and energy budgets.

Ultrafiltration of thin stillage from conventional and e-mill dry grind processes.

PubMed

Arora, Amit; Dien, Bruce S; Belyea, Ronald L; Wang, Ping; Singh, Vijay; Tumbleson, M E; Rausch, Kent D

2011-05-01

We used ultrafiltration (UF) to evaluate membrane filtration characteristics of thin stillage and determine solids and nutrient compositions of filtered streams. To obtain thin stillage, corn was fermented using laboratory methods. UF experiments were conducted in batch mode under constant temperature and flow rate conditions. Two regenerated cellulose membranes (10 and 100 kDa molecular weight cutoffs) were evaluated with the objective of retaining solids as well as maximizing permeate flux. Optimum pressures for 10 and 100 kDa membranes were 207 and 69 kPa, respectively. Total solids, ash, and neutral detergent fiber contents of input TS streams of dry grind and E-Mill processes were similar; however, fat and protein contents were different (p < 0.05). Retentate obtained from conventional thin stillage fractionation had higher mean total solids contents (27.6% to 27.8%) compared to E-Mill (22.2% to 23.4%). Total solids in retentate streams were found similar to those from commercial evaporators used in industry (25% to 35% total solids). Fat contents of retentate streams ranged from 16.3% to 17.5% for the conventional process. A 2% increment in fat concentration was observed in the E-Mill retentate stream. Thin stillage ash content was reduced 60% in retentate streams.

Nutrition quality test of fermented waste vegetables by bioactivator local microorganisms (MOL) and effective microorganism (EM4)

NASA Astrophysics Data System (ADS)

Mirwandono, E.; Sitepu, M.; Wahyuni, T. H.; Hasnudi; Ginting, N.; Siregar, G. AW; Sembiring, I.

2018-02-01

Livestock feed mostly used waste which has low nutrition content and one way to improve feed content by fermentation. The objective of this study was to evaluate the effect of bioactifator types on fermented vegetables waste for animal feed.The research was conducted in Nutrition and Animal Feed Laboratory, Universitas Sumatera Utara from May until July 2016. The research was factorial completely randomized design of 3 x 3 with 3 replications. Factor I were bioactivator types which were control, local bioactivator and EM4 (Effective Microorganisms 4). Factor II were time of incubation 3, 5 and 7 days. Parameters were moisture content, ash, Nitrogen Free Extract (NFE) and Total Digestible Nutrient (TDN). The results showed that bioactivator types either local activator or EM4 has highly significantly different effect (P<0,01) on water content, NFE and TDN on vegetables waste while there was no different between local bioactifator with EM4 on all parameters. Time of incubation 7 days has highly significantly different effect (P<0,01) on NFE, TDN and significant different (P<0,05) on water content and ash. In conclusion local bioactifators could improve animal feed by fermenting vegetables waste and it is more available for livestockers.

Salt-soda sinter process for recovering aluminum from fly ash

DOEpatents

McDowell, William J.; Seeley, Forest G.

1981-01-01

A method for recovering aluminum values from fly ash comprises sintering the fly ash with a mixture of NaCl and Na.sub.2 CO.sub.3 to a temperature in the range 700.degree.-900.degree. C. for a period of time sufficient to convert greater than 90% of the aluminum content of the fly ash into an acid-soluble fraction and then contacting the thus-treated fraction with an aqueous solution of nitric or sulfuric acid to effect dissolution of aluminum and other metal values in said solution.

Salt-soda sinter process for recovering aluminum from fly ash

DOEpatents

McDowell, W.J.; Seeley, F.G.

A method for recovering aluminum values from fly ash comprises sintering the fly ash with a mixture of NaCl and Na/sub 2/CO/sub 3/ to a temperature in the range 700/sup 0/ to 900/sup 0/C for a period of time sufficient to convert greater than 90% of the aluminum content of the fly ash into an acidsoluble fraction and then contacting the thus-treated fraction with an aqueous solution of nitric or sulfuric acid to effect dissolution of aluminum and other metal values in said solution.

Trace element emissions from spontaneous combustion of gob piles in coal mines, Shanxi, China

USGS Publications Warehouse

Zhao, Y.; Zhang, Jiahua; Chou, C.-L.; Li, Y.; Wang, Z.; Ge, Y.; Zheng, C.

2008-01-01

The emissions of potentially hazardous trace elements from spontaneous combustion of gob piles from coal mining in Shanxi Province, China, have been studied. More than ninety samples of solid waste from gob piles in Shanxi were collected and the contents of twenty potentially hazardous trace elements (Be, F, V, Cr, Mn, Co, Ni, Cu, Zn, As, Se, Mo, Cd, Sn, Sb, Hg, Tl, Pb, Th, and U) in these samples were determined. Trace element contents in solid waste samples showed wide ranges. As compared with the upper continental crust, the solid waste samples are significantly enriched in Se (20x) and Tl (12x) and are moderately enriched in F, As, Mo, Sn, Sb, Hg, Th, and U (2-5x). The solid waste samples are depleted in V, Cr, Mn, Co, Ni, Cu, and Zn. The solid waste samples are enriched in F, V, Mn, Cr, Co, Ni, Cu, Zn, Sb, Th, and U as compared with the Shanxi coals. Most trace elements are higher in the clinker than in the unburnt solid waste except F, Sn, and Hg. Trace element abundances are related to the ash content and composition of the samples. The content of F is negatively correlated with the ash content, while Pb is positively correlated with the ash. The concentrations of As, Mn, Zn, and Cd are highly positively correlated with Fe2O3 in the solid waste. The As content increases with increasing sulfur content in the solid waste. The trace element emissions are calculated for mass balance. The emission factors of trace elements during the spontaneous combustion of the gobs are determined and the trace element concentrations in the flue gas from the spontaneous combustion of solid waste are calculated. More than a half of F, Se, Hg and Pb are released to the atmosphere during spontaneous combustion. Some trace element concentrations in flue gas are higher than the national emission standards. Thus, gob piles from coal mining pose a serious environmental problem. ?? 2007 Elsevier B.V. All rights reserved.

Quality Evaluation of Biscuits Supplemented with Alfalfa Seed Flour

PubMed Central

Ullah, Fahim; Ahmad, Sajjad; Wahab, Said; Zeb, Alam; Khan Khattak, Mansoor; Khan, Saleem; Kang, Min

2016-01-01

The effect of alfalfa seed flour supplementation on the quality characteristics of refined wheat flour-based biscuits was studied. The proximate composition of refined wheat flour and alfalfa seed flour was determined. Refined wheat flour contained 12.43% moisture, 11.52% crude protein, 1.61% crude fat, 0.71% crude fiber, 1.43% ash and 70.83% nitrogen free extract, while alfalfa seed flour contained 5.79%, 29.49%, 12.71%, 5.53%, 4.80% and 41.73% moisture, crude protein, crude fat, crude fiber, ash and nitrogen free extract correspondingly. Alfalfa seed flour at 5%, 10%, 15% and 20% supplementation levels was incorporated in refined wheat flour to produce composite flour. The biscuits prepared were subjected to quality evaluation. Physical analysis of biscuits disclosed that supplementation of alfalfa seed flour decreased the width from 47.25 to 42 mm and the spread factor from 62.7 to 53.12, while it increased the thickness from 7.53 to 8.10 mm. Supplementation of refined wheat flour–based biscuits with alfalfa seed flour at different inclusion levels significantly (p < 0.05) increased the crude protein content from 10.19% to 15.30%, the crude fiber content from 0.73% to 1.62%, the crude fat content from 17.46% to 21.59% and the ash content from 1.37% to 1.92%, whereas it decreased the moisture content from 3.57% to 3.26% and the nitrogen free extract from 66.90% to 59.32%. The effect of supplementation on the mineral contents of biscuits was also significant (p < 0.05). Potassium, magnesium, calcium, iron and zinc contents increased from 105.30, 14.65, 43.91, 3.74 and 0.94 to 145.00, 26.64, 79.60, 7.93 and 1.60 mg/100 g, respectively. Sensory evaluation revealed that the quality score of biscuits in terms of color, taste, texture and overall acceptability decreased with increased supplementation. The present research work confirmed that a maximum of 10% alfalfa seed flour supplementation in refined wheat flour could produce acceptable biscuits with an appropriate nutritional profile. PMID:28231168

The partitioning of heavy metals in incineration of sludges and waste in a bubbling fluidized bed 2. Interpretation of results with a conceptual model.

PubMed

Toledo, José M; Corella, José; Corella, Luis M

2005-11-11

This work addresses the behavior, fate and/or partitioning of six targeted (Cd, Pb, Cr, Cu, Zn and Ni) heavy metals (HMs) in the incineration of sludges and waste in a bubbling fluidized bed (BFB) of 15 cm i.d. and 5.2m high followed by a filter chamber operated at 750-760 degrees C with a commercial ceramic filter. This paper presents three different things: (1) an in depth review of the published work relating to the problem of partitioning of the HMs in BFBs, (2) some more experimental incineration tests regarding the influence of the temperature of the bed of the BFB and the effect of the chlorine content in the feedstock on the partitioning of the HMs, and (3) the modelling of the partitioning of the HMs in the exit flows: bottom ash, coarse fly ashes, fine fly ash and vapour phase. The partitioning of the HMs is governed by fluid dynamic principles together with the kinetics of the diffusion of the HMs inside the ash particles and the kinetics of the reactions between the HMs and the components of the matrix of the ash. Some thermodynamic predictions do not fit the results from the BFB incinerator well enough because equilibria are not reached in at least three exit ash flows: coarse fly ash, fine fly ash and submicron particles. The residence time of these ash particles in these type of incinerators is very short and most of the HMs have no time to diffuse out of the ash particle. Finally, an examination was made on how in the ceramic hot filter the partition coefficients for the HMs increased, mainly for Cd and Pb, when the Cl-content in the feedstock was increased.

In-plant testing of a novel coal cleaning circuit using advanced technologies. Final technical report, September 1, 1995--August 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Honaker, R.Q.; Reed, S.; Mohanty, M.K.

1997-05-01

A circuit comprised of advanced fine coal cleaning technologies was evaluated in an operating preparation plant to determine circuit performance and to compare the performance with current technologies used to treat -16 mesh fine coal. The circuit integrated a Floatex hydrosizer, a Falcon enhanced gravity concentrator and a Jameson flotation cell. A Packed-Column was used to provide additional reductions in the pyritic sulfur and ash contents by treatment of the Floatex-Falcon-Jameson circuit product. For a low sulfur Illinois No. 5 coal, the pyritic sulfur content was reduced from 0.67% to 0.34% at a combustible recovery of 93.2%. The ash contentmore » was decreased from 27.6% to 5.84%, which equates to an organic efficiency of 95% according to gravity-based washability data. The separation performance achieved on a high sulfur Illinois No. 5 coal resulted in the rejection of 72.7% of the pyritic sulfur and 82.3% of the ash-forming material at a recovery of 8 1 %. Subsequent pulverization of the cleaned product and retreatment in a Falcon concentrator and Packed-Column resulted in overall circuit ash and pyritic sulfur rejections of 89% and 93%, respectively, which yielded a pyritic sulfur content reduction from 2.43% to 0.30%. This separation reduced the sulfur dioxide emission rating of an Illinois No. 5 coal from 6.21 to 1.75 lbs SO{sub 2}/MBTU, which is Phase I compliance coal. A comparison of the results obtained from the Floatex-Falcon-Jameson circuit with those of the existing circuit revealed that the novel fine coal circuit provides 10% to 20% improvement in mass yield to the concentrate while rejecting greater amounts of ash and pyritic sulfur.« less

21 CFR 137.320 - Semolina.

Code of Federal Regulations, 2011 CFR

2011-04-01

... coat, or bran coat and germ, to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 0.92 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash and moisture are determined by the methods therefor referred to in...

21 CFR 137.320 - Semolina.

Code of Federal Regulations, 2014 CFR

2014-04-01

... coat, or bran coat and germ, to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 0.92 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash and moisture are determined by the methods therefor referred to in...

21 CFR 137.320 - Semolina.

Code of Federal Regulations, 2012 CFR

2012-04-01

... coat, or bran coat and germ, to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 0.92 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash and moisture are determined by the methods therefor referred to in...

21 CFR 137.320 - Semolina.

Code of Federal Regulations, 2010 CFR

2010-04-01

... coat, or bran coat and germ, to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 0.92 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash and moisture are determined by the methods therefor referred to in...

21 CFR 137.320 - Semolina.

Code of Federal Regulations, 2013 CFR

2013-04-01

... coat, or bran coat and germ, to such extent that the percent of ash therein, calculated to a moisture-free basis, is not more than 0.92 percent. Its moisture content is not more than 15 percent. (b) For the purpose of this section, ash and moisture are determined by the methods therefor referred to in...

Utilization of low-ash biochar to partially replace carbon black in SBR composites

USDA-ARS?s Scientific Manuscript database

A biochar made from woody waste feedstock with low ash content was blended with carbon black as filler for styrene-butadiene rubber. At 10% total filler concentration (w/w), composites made from 25 or 50% biochar showed improved tensile strength, elongation, and toughness compared to similar composi...

Coal fly ash as a resource for rare earth elements.

PubMed

Franus, Wojciech; Wiatros-Motyka, Małgorzata M; Wdowin, Magdalena

2015-06-01

Rare earth elements (REE) have been recognised as critical raw materials, crucial for many clean technologies. As the gap between their global demand and supply increases, the search for their alternative resources becomes more and more important, especially for the countries which depend highly on their import. Coal fly ash (CFA), which when not utilised is considered waste, has been regarded as the possible source of many elements, including REE. Due to the increase in the energy demand, CFA production is expected to grow, making research into the use of this material a necessity. As Poland is the second biggest coal consumer in the European Union, the authors have studied different coal fly ashes from ten Polish power plants for their rare earth element content. All the fly ashes have a broadly similar distribution of rear earth elements, with light REE being dominant. Most of the samples have REE content relatively high and according to Seredin and Dai (Int J Coal Geol 94: 67-93, 2012) classification can be considered promising REE raw materials.

National Coal Quality Inventory (NACQI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert Finkelman

2005-09-30

The U.S. Geological Survey (USGS) conducted the National Coal Quality Inventory (NaCQI) between 1999 and 2005 to address a need for quality information on coals that will be mined during the next 20-30 years. Collaboration between the USGS, State geological surveys, universities, coal burning utilities, and the coal mining industry plus funding support from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE) permitted collection and submittal of coal samples for analysis. The chemical data (proximate and ultimate analyses; major, minor and trace element concentrations) for 729 samples of raw or prepared coal, coal associated shale,more » and coal combustion products (fly ash, hopper ash, bottom ash and gypsum) from nine coal producing States are included. In addition, the project identified a new coal reference analytical standard, to be designated CWE-1 (West Elk Mine, Gunnison County, Colorado) that is a high-volatile-B or high-volatile-A bituminous coal with low contents of ash yield and sulfur, and very low, but detectable contents of chlorine, mercury and other trace elements.« less

Biometric studies on the bivalves Astarte elliptica, A. borealis and A. montagui in Kiel Bay (Western Baltic Sea)

NASA Astrophysics Data System (ADS)

Schaefer, R.; Trutschler, K.; Rumohr, H.

1985-09-01

The three Astarte species were studied in June 1983 at two sites in Kiel Bay, “Süderfahrt” and “Schleimünde”, at 20 m depth. Shell length to live wet weight correlations are given for all three species; for A. elliptica also shell-free dry weight, shell dry weight, ash-free dry weight of the soft body and ash-free dry weight of the shell are recorded as functions of the shell length. In the logarithmic length/weight regression analysis the coefficients of slope for A. elliptica and A. borealis are 3. For A. montagui, that coefficient is significantly greater than 3. Weight conversion factors, calculated for A. elliptica, revealed a mean weight composition of 31.5 % water in the mantle cavity and tissue water, 64.5 % shell ash, 2.1 % organic content of shell, 1.7 % organic content of the soft body and 0.4 % ash of the soft body. An isometric growth of shell length and shell breadth is confirmed for A. borealis, while A. montagui exhibits positive allometric shell growth and changes its shape during life.

Characteristics of and sorption to biochars derived from waste material

NASA Astrophysics Data System (ADS)

Sun, Huichao; Kah, Melanie; Sigmund, Gabriel; Hofmann, Thilo

2015-04-01

Biochars can exhibit a high sorption potential towards heavy metals and organic contaminants in various environmental matrices (e.g., water, soil). They have therefore been proposed for environmental remediation purposes to sequester contaminants. To date, most studies have focused on the physicochemical and sorption properties of mineral phases poor biochars, which are typically produced from plant residues. Only little knowledge is available for biochars derived from human and animal waste material, which are typically characterized by high mineral contents (e.g., sewage sludge, manure). Using human and animal waste as source material to produce biochars would support the development of attractive combined strategies for waste management and remediation. The potential impact of mineral phases on the physicochemical and sorption properties of biochars requires further studies so that the potential as sorbent material can be evaluated. With this purpose, different source material biochars were produced at 200°C, 350°C and 500°C, to yield a series of biochars representing a range of mineral content. The derived biochars from wood shavings (<1% ash), sewage sludge (50-70% ash) and pig manure (30-60% ash), as well as a commercial biochar derived from grain husks (40% ash), were extensively characterized (e.g., element composition, surface area, porosity, Fourier transform infrared spectroscopy). The contents of potentially toxic elements (i.e., heavy metals and polycyclic aromatic hydrocarbons) of all materials were within the guidelines values proposed by the International Biochar Initiative, indicating their suitability for environmental application. Single point sorption coefficients for the model sorbate pyrene were measured to investigate the effect of mineral content, feedstock, pyrolysis temperature, particle size fractions and acid demineralization on sorption behavior. Overall, sorption of pyrene was strong for all materials (4 < Log Kd < 6.5 L/kg). Sorption generally increased with increasing pyrolysis temperature but there was no effect of particle size on sorption affinity. For mineral phase rich biochars, sorption generally increased after acid demineralization. When considering all materials together, the sorbent aromaticity (hydrogen-carbon ratio) was the most important factor controlling sorption of pyrene. Overall, the study demonstrates that biochars derived from human and animal waste material and exhibiting high mineral contents have potential for remediation applications.

Palynology, petrography and geochemistry of the Sewickley coal bed (Monongahela Group, Late Pennsylvanian), Northern Appalachian Basin, USA

USGS Publications Warehouse

Eble, C.F.; Pierce, B.S.; Grady, W.C.

2003-01-01

Forty-two bench samples of the Sewickley coal bed were collected from seven localities in the northern Appalachian Basin and analyzed palynologically, petrographically, and geochemically. The Sewickley coal bed occurs in the middle of the Pittsburgh Formation (Monongahela Group) and is of Late Pennsylvanian age. Palynologically, it is dominated by spores of tree ferns. Tree fern spore taxa in the Sewickley include Punctatisporites minutus, Punctatosporites minutus, Laevigatosporites minimus, Spinosporites exiguus, Apiculatasporites saetiger, and Thymospora spp. In fact, Punctatisporites minutus was so abundant that it had to be removed from the standard counts and recorded separately (average 73.2%). Even when Punctatisporites minutus is removed from the counts, tree fern spores still dominate a majority of the assemblages, averaging 64.4%. Among the tree fern spores identified in the Sewickley coal, Thymospora exhibits temporal and spatial abundance variation. Thymospora usually increases in abundance from the base to the top of the bed. Thymospora is also more abundant in columns that are thick (>100 cm) and low in ash yield (< 12.0%, dry basis). Calamite spores (e.g. Calamospora spp., Laevigatosporites minor, and L. vulgaris) are the next most abundant plant group represented in the Sewickley coal, averaging 20%. Contributions from all other plant groups are minor in comparison. Petrographically, the Sewickley coal contains high percentages of vitrinite (average 82.3%, mineral matter-free (mmf)), with structured forms being more common than unstructured forms. In contrast, liptinite and inertinite macerals both occur in low percentages (average 7.7% and 10.0%, respectively). Geochemically, the Sewickley coal has a moderate ash yield (average 12.4%) and high total sulfur content (average 3.4%). Four localities contained a high ash or carbonaceous shale bench. These benches, which may be coeval, are strongly dominated by tree fern spores. Unlike the lower ash benches, they contain low percentages of vitrinite, which mainly occurs as unstructured vitrinite, and higher liptinite and inertinite contents. The accumulated data suggest that the Sewickley paleomire was probably a rheotrophic, planar mire that had a consistent water cover. This is supported by the high vitrinite contents, moderate ash yields, and high total sulfur contents. The high ash and carbonaceous shale benches probably represent either periods of dryness and substrate exposure, or flooding of the mire surface, the duration of which is unknown. ?? 2003 Elsevier B.V. All rights reserved.

Characterization of black carbon and organic contaminants in wood ash from different feedstocks and types of furnaces

NASA Astrophysics Data System (ADS)

Merino, Agustin; Rey-Salgueiro, Ledicia; Omil, Beatriz; Martinez-Carballo, Elena; Simal-Gandara, Jesus

2015-04-01

Due to their important concentration of nutrient and charcoal, wood ash from biomass power plants (WA) can be used as a fertilizer and organic amendment in intensively managed soils. Unlike biochar produced in under anoxic conditions, the nature of the organic compounds present in wood ash has been scarcely studied. Due to the incomplete combustion, wood ash may contain a wide range of organic compounds, from charred to highly condensed refractory biomass, which determines the possibilities of WA as an organic amendment. In addition, the possible environmental risk of this practice must be assessed by determining the content of water-soluble and insoluble organic contaminants. due to the incomplete combustion of organic matter, organic pollutants, such as Polycyclic Aromatic Hydrocarbons (PAHs), can be formed and can remain in the combustion residue. Also, the four alkyl benzene volatile organic compounds (benzene, toluene, ethylbenzene, and the ortho, para, and meta xylenes) can be formed, depending on certain conditions during combustion. For this study 15 biomass power stations in Spain were selected. In all of them the feedstock is pine or eucalyptus branches and bark. Nine of them were bottom wood ash generated from wood fires furnaces, obtained from grate-fired or water-tube boilers. Whereas four of them were fly ash, obtained in cyclone separators. The samples were collected following a common procedure to ensure the representiveness of the sampling. Bottom ash samples were fraccionated in three fractions: < 2mm, 2-5 mm and > 5mm. Each fraction was characterized for organic matter and BTEX, styrene and total petroleum hydrocarbons Polycyclic Aromatic Hydrocarbons. For each analyzes, three replicates were analyzed per sample. Mixes wood ash shows higher amounts of charred material than fly ash. The 13 C CPMAS NMR, DSC/TG and FTIR analysis showed the loss of carbohydrates and aliphatic constituents and revealed the formation of aromatic compounds. The atomic H/C ratios, NMR spectra, DSC and FTIR confirmed the presence of condensed structures, specially in the coarse particles. However, the different wood ash showed an important range of properties revealing the presence from charred material to charcoal containing condensed structures (H/C ratios lower than 0.6; aromaticity higher than 80 % and T50-DSC higher than 500 °C). Typical organic pollutants including those water-soluble such as BTEX plus styrene, but also those water-insoluble such as polycyclic aromatic hydrocarbons (PAHs), together with aliphatic hydrocarbons, were examined in the ash. Their contents were related to degree of combustion of the biomass, determined through the content and composition of the organic matter in the wood ash. The sum of BTEX plus styrene varied from non-detected to 30 mg/kg, and the total amounts of PAHs (total PAHs) ranged between non-detected and 422 µg/kg, not exceeding the regulated limits. This research provides basic information for the evaluation of the environmental risk and potential uses of WW incinerator bottom ash The results demonstrate the important variability in the charred material properties of the different power plants and size-particles. The organic compounds contents are also variable, but in all cases were levels of pollutants in all the samples were below the limits for both soil and industrial use (Environmental Protection Agency in the European Union and the USA.

Analysis of Phyllostachys pubescens bamboo residues for liquefaction: chemical components, infrared spectroscopy, and thermogravimetry

Treesearch

Jinqiu Qi; Chung-Yun Hse; Todd F. Shupe

2013-01-01

Residues of Phyllostachys pubescens bamboo obtained from central Louisiana, USA, were comprehensively investigated for use in liquefaction. The results showed that bamboo branches had the highest Klason lignin and ash content, about 26% and 2.75%, respectively. The epidermis layer sample had relatively higher carbohydrate content, while the wax layer sample had the...

Characterization of Arab medium crude fractions with emphasis on kinematic viscosity - temperature behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beg, S.A.; Amin, M.B.; Hussain, I.

1986-01-01

Characterization of Arab medium Crude Oil, has been carried out in terms of API gravity, debutanized crude gravity, total sulfur content, Reid vapour pressure ash content, heating value, salt content, viscosity SUS, vanadium content as V/sub 2/O/sub 5/, pour point and analysis of various metals. Further, six true boiling point (TBP) fractions (IBP-95/sup 0/C, 95-205/sup 0/C, 205-260/sup 0/C, 260-345/sup 0/C, 345-455/sup 0/C and 455/sup 0/C+) of this crude were characterized in terms of API gravity, total sulfur contents H/sub 2/S content, mercaptons content, molecular weight, elemental analyses for total carbon, hydrogen and nitrogen, analyses of various metals and paraffin, aromaticmore » and naphthene contents of lighter fractions. The kinematic viscosity-temperature data have been obtained for 95/sup 0/C+ TBP fractions for a wide range of temperatures.« less

Physicochemical Characteristics of Black Garlic after Different Thermal Processing Steps

PubMed Central

Kang, Ok-Ju

2016-01-01

This study investigated the physicochemical characteristics of black garlic (BG) after different thermal processing steps. Compared with fresh garlic (FG), the moisture content and pH in BG decreased significantly, while the ash content and browning intensity increased during thermal processing. The total mineral and the free sugar contents were significantly higher than that of the BG2 and BG4 samples, respectively. The free sugar content increased by 16-fold in the BG cloves compared with that of FG, while the amino acid content increased during the first stage of thermal processing, and subsequently decreased. The thiosulfinate content in all samples decreased to during thermal processing. The pyruvic acid content initially increased and then decreased during thermal processing. These results contribute to our understanding of the role of thermal processing in the quality formation of BG. PMID:28078257

Physical and Chemical Character of Fly Ash of Coal Fired Power Plant in Java

NASA Astrophysics Data System (ADS)

Triwulan; Priadana, K. A.; Ekaputri, J. J.; Bayuaji, R.

2017-11-01

Quality of fly ash is varying widely in the field, it depends on the combustion process and the quality of the basic ingredients, namely coal. It will affect the physical and mechanical properties of the concrete mixtures used. This study used 12 samples of fly ash. The physical and chemical properties and finesse modulus were analyzed. The fly ash was mixed with OPC (Ordinary Portland Cement) with the proportion of 20% fly ash and 80% OPC. The specimens were form with mortar dimension of 5cm x 5 cm. The test was affected by the correlation of fly ash fineness modulus to compressive strength, correlation density of fly ash to compressive strength, and correlation of carbon content to the compressive strength.

Proximate composition, nutritional attributes and mineral composition of Peperomia pellucida L. (Ketumpangan Air) grown in Malaysia.

PubMed

Ooi, Der-Jiun; Iqbal, Shahid; Ismail, Maznah

2012-09-17

This study presents the proximate and mineral composition of Peperomia pellucida L., an underexploited weed plant in Malaysia. Proximate analysis was performed using standard AOAC methods and mineral contents were determined using atomic absorption spectrometry. The results indicated Peperomia pellucida to be rich in crude protein, carbohydrate and total ash contents. The high amount of total ash (31.22%)suggests a high-value mineral composition comprising potassium, calcium and iron as the main elements. The present study inferred that Peperomia pellucida would serve as a good source of protein and energy as well as micronutrients in the form of a leafy vegetable for human consumption.

Size fractionation as a tool for separating charcoal of different fuel source and recalcitrance in the wildfire ash layer.

PubMed

Mastrolonardo, Giovanni; Hudspith, Victoria A; Francioso, Ornella; Rumpel, Cornelia; Montecchio, Daniela; Doerr, Stefan H; Certini, Giacomo

2017-10-01

Charcoal is a heterogeneous material exhibiting a diverse range of properties. This variability represents a serious challenge in studies that use the properties of natural charcoal for reconstructing wildfires history in terrestrial ecosystems. In this study, we tested the hypothesis that particle size is a sufficiently robust indicator for separating forest wildfire combustion products into fractions with distinct properties. For this purpose, we examined two different forest environments affected by contrasting wildfires in terms of severity: an eucalypt forest in Australia, which experienced an extremely severe wildfire, and a Mediterranean pine forest in Italy, which burned to moderate severity. We fractionated the ash/charcoal layers collected on the ground into four size fractions (>2, 2-1, 1-0.5, <0.5mm) and analysed them for mineral ash content, elemental composition, chemical structure (by IR spectroscopy), fuel source and charcoal reflectance (by reflected-light microscopy), and chemical/thermal recalcitrance (by chemical and thermal oxidation). At both sites, the finest fraction (<0.5mm) had, by far, the greatest mass. The C concentration and C/N ratio decreased with decreasing size fraction, while pH and the mineral ash content followed the opposite trend. The coarser fractions showed higher contribution of amorphous carbon and stronger recalcitrance. We also observed that certain fuel types were preferentially represented by particular size fractions. We conclude that the differences between ash/charcoal size fractions were most likely primarily imposed by fuel source and secondarily by burning conditions. Size fractionation can therefore serve as a valuable tool to characterise the forest wildfire combustion products, as each fraction displays a narrower range of properties than the whole sample. We propose the mineral ash content of the fractions as criterion for selecting the appropriate number of fractions to analyse. Copyright © 2016. Published by Elsevier B.V.

Development of a video-based slurry sensor for on-line ash analysis. Fifth quarterly technical progress report, October 1, 1995--December 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adel, G.T.; Luttrell, G.H.

Automatic control of fine coal cleaning circuits has traditionally been limited by the lack of sensors for on-line ash analysis. Although several nuclear-based analyzers are available, none have seen widespread acceptance. This is largely due to the fact that nuclear sensors are expensive and tend to be influenced by changes in seam type and pyrite content. Recently, researchers at VPI&SU have developed an optical sensor for phosphate analysis. The sensor uses image processing technology to analyze video images of phosphate ore. It is currently being used by PCS Phosphate for off-line analysis of dry flotation concentrate. The primary advantages ofmore » optical sensors over nuclear sensors are that hey are significantly cheaper, are not subject to measurement variations due to changes in high atomic number materials, are inherently safer and require no special radiation permitting. The purpose of this work is to apply the knowledge gained in the development of an optical phosphate analyzer to the development of an on-line ash analyzer for fine coal slurries. During the past quarter, the current prototype of the on-line optical ash analyzer was subjected to extensive testing at the Middlefork coal preparation plant. Initial work focused on obtaining correlations between ash content and mean gray level, while developmental work on the more comprehensive neural network calibration approach continued. Test work to date shows a promising trend in the correlation between ash content and mean gray level. Unfortunately, data scatter remains significant. Recent tests seem to eliminate variations in percent solids, particle size distribution, measurement angle and light setting as causes for the data scatter; however, equipment warm-up time and number of images taken per measurement appear to have a significant impact on the gray-level values obtained. 8 figs., 8 tabs.« less

Ameliorating Effects of Exogenously Applied Proline on Seed Composition, Seed Oil Quality and Oil Antioxidant Activity of Maize (Zea mays L.) under Drought Stress

PubMed Central

Ali, Qasim; Anwar, Farooq; Ashraf, Muhammad; Saari, Nazamid; Perveen, Rashida

2013-01-01

This study was carried out to appraise whether or not the exogenous application of a potential osmoprotectant, proline, could ameliorate the adverse effects of drought stress on maize seed and seed oil composition, as well as oil antioxidant activity. Water stress reduced the kernel sugar, oil, protein and moisture contents and most of the seed macro- and micro-elements analyzed in both maize cultivars but it increased the contents of seed fiber and ash. Water stress increased the oil oleic acid content with a subsequent decrease in the amount of linoleic acid, resulting in an increased oil oleic/linoleic ratio for both maize cultivars. However, no variation was observed in oil stearic and palmitic acids content due to water stress. A considerable drought induced an increase in seed oil α-, γ-, δ- and total tocopherols and flavonoids were observed in both maize cultivars. However, oil phenolic and carotenoid content as well as 1,1-diphenyl-2-picryl-hydrazyl (DPPH) free radical scavenging activity decreased. Foliar-applied proline significantly increased the content of seed sugar, oil, protein, moisture, fiber and ash in both maize cultivars under well irrigated and water deficit conditions. Furthermore, exogenous application of proline increased the oil oleic and linoleic acid contents. The concentrations of antioxidant compounds namely phenolics, carotenoids, flavonoids and tocopherols estimated in the seed oil increased due to foliar-applied proline under water deficit conditions that was positively correlated with the enhanced oil DPPH free radical scavenging activity. Moreover, the increase in the contents of these antioxidant compounds and oil antioxidant activity due to the foliar application of proline was noted to be more pronounced under water deficit conditions. PMID:23344043

Thermo-mechanical properties and microfabric of fly ash-stabilized gold tailings.

PubMed

Lee, Joon Kyu; Shang, Julie Q; Jeong, Sangseom

2014-07-15

This paper studies the changes in thermal conductivity, temperature, and unconfined compressive strength of gold tailings and fly ash mixtures during the curing period of 5 days. The microfabric of the cured mixtures was investigated with mercury intrusion porosimetry (MIP). The mixture samples were prepared at their maximum dry unit weight and optimum moisture content. Effect of adding fly ash to gold tailings (i.e., 0, 20, and 40% of the dry weight of tailings) was examined, and a comparison was made on samples prepared at the same fly ash content by replacing gold tailings with humic acid (i.e., gold tailings and humic acid ratios of 100:0, 90:10, and 80:20 by weight) or by varying pore fluid chemistry (i.e., water and salt solutions of 1M NaCl and CaCl2). The results show that the initial thermal conductivity of the samples is sensitive to the mixture proportion and a declination in the thermal conductivity is observed due to hydration of fly ash and evaporation. Inclusion of fly ash and salts into gold tailings improves the unconfined compressive strength but the presence of humic acid in samples leads to the decrease of the strength. MIP results reveal the pore structure changes associated with the packing states of the samples that reflect the influential factors considered. Copyright © 2014 Elsevier B.V. All rights reserved.

Potassic zeolites from Brazilian coal ash for use as a fertilizer in agriculture.

PubMed

Flores, Camila Gomes; Schneider, Helena; Marcilio, Nilson Romeu; Ferret, Lizete; Oliveira, João Carlos Pinto

2017-12-01

Brazilian coal has an ash content ranging from 30 to 50% by weight. Consequently, its use in coal-fired thermoelectric for power production generates a lot of waste. The construction sector is the largest consumer of coal ash, but it cannot absorb the entire amount generated. Thus, other applications for coal ash should be studied in aim to optimize the use of this industrial waste. This research had as focus to synthesize potassic zeolite from of the coal ash into on potassium fertilizer for the grown wheat plant. In this work, it was used a subbituminous coal from Mina do Leão (RS, Brazil) presenting 48.7% ash content on a dry basis. Concerning the synthesis of potassic zeolite, it was adopted the conventional method of hydrothermal treatment with potassium hydroxide. A schedule of experiments was conducted in order to define the optimum condition of zeolite synthesis that was then used an alkaline solution of 5M KOH with a reaction time of 24h at 150°C. According to this procedure, it was obtained a zeolite with a single crystalline phase, identified through X-ray diffraction as Merlinoite. Subsequently, it was performed a set of tests using potassic zeolite asa fertilizer for plants in a greenhouse. The synthesized potassic zeolite showed a good potential for its use as fertilizer in agriculture. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lauryl Amine as heavy metal collector of boiler ash from pulp and paper mill waste

NASA Astrophysics Data System (ADS)

Sembiring, M. P.; Kaban, J.; Bangun, N.; Saputra, E.

2018-04-01

Theincreasing of demand of pulp and paper products, will following with the growing the pulp and paper industryand generate significant mill waste. The total waste reached 1/3 of the amount raw materials used and ash boiler is the waste with the largest percentage of 52%. For that it takes effort to manage the existing waste. The boiler ash contained the chemical elements, it can be utilized such as fertilizer, because it also contains transition metals in form of heavy metal such as Cadmium (Cd), Cobalt (Co), Chrome (Cr), Cupprum (Cu), Ferrum (Fe), Nickel (Ni), and Zinc (Zn), the use of boiler ash must follow the threshold specified by the Government. Several studies have been undertaken to reduce and extract heavy metals from ash and sand of the boiler by using carbon dioxide as its ligand. Eelectrochemical method was used to remove and recovery of heavy metals from the incenerator. This study focused on removal of heavy metals using Lauryl Amine as collector and three solvents namely Dichloromethane, Ethanol and n-Hexane. The treatmentswas able to extract the heavy metal and generally reduce the heavy metal content of ash boiler pulp and paper mill waste. The combination treatment used toreduce the heavy metal content of 5 gram Lauryl Amine collector in Dichloromethane solvent for 4 hours process time.

Amelioration of soil PAH and heavy metals by combined application of fly ash and biochar

NASA Astrophysics Data System (ADS)

Masto, Reginald; George, Joshy; Ansari, Md; Ram, Lal

2016-04-01

Generation of electricity through coal combustion produces huge quantities of fly ash. Sustainable disposal and utilization of these fly ash is a major challenge. Fly ash along with other amendments like biochar could be used for amelioration of soil. In this study, fly ash and biochar were used together for amelioration of polycyclic aromatic hydrocarbon (PAH) contaminated soil. Field experiment was conducted to investigate the effects of fly ash and biochar on the amelioration of soil PAH, and the yield of Zea mays. The treatments were control, biochar (4 t/ha), fly ash (4 t/ha), ash + biochar ( 2 + 2 t/ha). Soil samples were collected after the harvest of maize crop and analysed for chemical and biological parameters. Thirteen PAHs were analysed in the postharvest soil samples. Soil PAHs were extracted in a microwave oven at 120 °C using hexane : acetone (1:1) mixture. The extracted solutions were concentrated, cleaned and the 13 PAHs [Acenaphthene (Ace), fluorene (Flr), phenanthrene (Phn), anthracene(Ant), pyrene(Pyr), benz(a)anthracene (BaA), chrysene (Chy), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene, benzo(g,h,i)perylene (BghiP), dibenzo(a,h)anthracene, and indeno(1,2,3-cd)pyrene)(Inp)] were analysed using GC-MS. The mean pH increased from 6.09 in control to 6.64 and 6.58 at biochar and fly ash treated soils, respectively. N content was not affected, whereas addition of biochar alone and in combination with fly ash, has significantly increased the soil organic carbon content. P content was almost double in combined (9.06 mg/kg) treatment as compared to control (4.32 mg/kg). The increase in K due to biochar was 118%, whereas char + ash increased soil K by 64%. Soil heavy metals were decreased: Zn (-48.4%), Ni (-41.4%), Co (-36.9%), Cu (-35.7%), Mn (-34.3%), Cd (-33.2%), and Pb (-30.4%). Soil dehydrogenase activity was significantly increased by ash and biochar treatments and the maximum activity was observed for the combined treatment. Peroxidase, phenol oxidase, and catalase activities were not affected by these treatments. Acid phosphatase activity decreased, whereas alkaline phosphatase activity increased due to biochar and fly ash treatment. Microbial biomass carbon increased significantly (P < 0.05) with biochar (+27.9%), fly ash (19.8%), and char + ash (+27.9%) applications. Maize grain yield was increased by biochar (+11.4%) and char + ash (+28.1%) treatments. The total PAH concentration decreased from 4191 μg/kg in control to 1930 μg/kg in fly ash; 1509 μg/kg in biochar and 1011 μg/kg in ash + char treatments. Among the different PAHs the concentration was higher for BkF, which decreased from 713 μg/kg in control to 139 - 315 μg/kg under different treatments. Overall, combined application of fly ash and biochar was found to be effective in amelioration of soil quality parameters and improving crop yield.

Relationship between Particle Size Distribution of Low-Rank Pulverized Coal and Power Plant Performance

DOE PAGES

Ganguli, Rajive; Bandopadhyay, Sukumar

2012-01-01

Tmore » he impact of particle size distribution (PSD) of pulverized, low rank high volatile content Alaska coal on combustion related power plant performance was studied in a series of field scale tests. Performance was gauged through efficiency (ratio of megawatt generated to energy consumed as coal), emissions (SO 2 , NO x , CO), and carbon content of ash (fly ash and bottom ash). he study revealed that the tested coal could be burned at a grind as coarse as 50% passing 76 microns, with no deleterious impact on power generation and emissions. he PSD’s tested in this study were in the range of 41 to 81 percent passing 76 microns. here was negligible correlation between PSD and the followings factors: efficiency, SO 2 , NO x , and CO. Additionally, two tests where stack mercury (Hg) data was collected, did not demonstrate any real difference in Hg emissions with PSD. he results from the field tests positively impacts pulverized coal power plants that burn low rank high volatile content coals (such as Powder River Basin coal). hese plants can potentially reduce in-plant load by grinding the coal less (without impacting plant performance on emissions and efficiency) and thereby, increasing their marketability.« less

Characterizations of milkfish (Chanos chanos) meatballs as effect of nanoencapsulation liquid smoke addition

NASA Astrophysics Data System (ADS)

Swastawati, Fronthea; Ambaryanto; Cahyono, Bambang; Wijayanti, Ima; Chilmawati, Diana

2018-02-01

Milkfish meatballs are one of the value-added product that is potential to be developed because this product is favored by consumers. The aims of this study were mainly to evaluate the effect of nano encapsulation liquid smoke addition to the properties of milkfish meatballs. The different concentration (0%, 1%, 3% and 5%) of nano encapsulation liquid smoke was treated into milkfish meatballs with three replications. Test parameters used include texture (hardness, deformation and gel strength); proximate (moisture, protein, fat, ash and carbohydrates content); sensory (organoleptic and hedonic). Parametric data were analysis using ANOVA and non-parametric parameters using Kruskal Wallis test. Analysis of variant shows that nanoencapsulation gave significant effect on the hardness, deformation, and gel strength; protein, lipid, ash and water content(P<0,05), but gave no significant effect on carbohydrate (P >0.05). The best texture characteristic was obtained by milkfish meatball added with 1% of nanoencapsulation liquid smoke indicated by the moisture water; protein; fat; ash and carbohydrate content: 66,35%; 12,69%; 6,75%; 2,42% and 5,93% respectively. The best organoleptic and hedonic value of milkfish meatballs was achieved by a panelist at the sample with the addition of 1% liquid smoke, but this sample found gave no significance different to control in terms of sensory valle.

Influence of moisture content and temperature on degree of carbonation and the effect on Cu and Cr leaching from incineration bottom ash.

PubMed

Lin, Wenlin Yvonne; Heng, Kim Soon; Sun, Xiaolong; Wang, Jing-Yuan

2015-09-01

This study investigated the influence of moisture content and temperature on the degree of carbonation of municipal solid waste (MSW) incineration bottom ash (IBA) from two different incineration plants in Singapore. The initial rate of carbonation was affected by the nominal moisture content used. Carbonation temperature seemed to play a part in changing the actual moisture content of IBA during carbonation, which in turn affected the degree of carbonation. Results showed that 2h of carbonation was sufficient for the samples to reach a relatively high degree of carbonation that was close to the degree of carbonation observed after 1week of carbonation. Both Cu and Cr leaching also showed significant reduction after only 2h of carbonation. Therefore, the optimum moisture content and temperature were selected based on 2h of carbonation. The optimum moisture content was 15% for both incineration plants while the optimum temperature was different for the two incineration plants, at 35°C and 50°C. The effect on Cu and Cr leaching from IBA after accelerated carbonation was evaluated as a function of carbonation time. Correlation coefficient, Pearson's R, was used to determine the dominant leaching mechanism. The reduction in Cu leaching was found to be contributed by both formation of carbonate mineral and reduction of DOC leaching. On the other hand, Cr leaching seemed to be dominantly controlled by pH. Copyright © 2015 Elsevier Ltd. All rights reserved.

Formulation and characterization of bread using coconut-pulp flour and wheat flour composite with addition of xanthan-gum

NASA Astrophysics Data System (ADS)

Erminawati; Sidik, W.; Listanti, R.; Zulfakar, H.

2018-01-01

Coconut-pulp flour is coconut flour made from by-product of coconut-milk based food products. The flour contains no gluten and high fibre, which can be considered as functional potential food. Bread made from composite-flour of coconut-pulp flour and wheat flour was studied for its physic-chemical and sensory characteristics. Addition of hydrocolloid, like xanthan-gum, was aimed to provide viscoelasticity for the dough which is essential for baked product. Composite-flour proportion used in this study was; 10CPF/90WF, 15CPF/85WF and 20CPF/80WF; and xanthan gum to total flour of 0,1% and 0,4%. Variable observed were; crumb-texture, crumb-colour, taste of coconut, preference and flavour; moisture, ash, fiber and soluble-protein contents. The research showed that addition of coconut-pulp flour in the composite-flour decreased specific volume value and increased the bread texture produced. It also increased the bread moisture-content, ash-content, fibre-content and soluble protein-content. Moreover, the xanthan-gum addition resulted in decreased specific-volume value and increased texture and fiber-content of the bread produced. Overall, the sensory characteristic of crumb colour, flavour and panellist preference revealed better than control bread made from wheat flour, however its crumb texture harder compare to control bread made from wheat flour. This study showed that coconut-pulp flour potential to be developed for production of functional food.

A test of bone mobilization relative to reproductive demand: skeletal quality is improved in cannibalistic females with large litters.

PubMed

Hood, Wendy R

2012-01-01

In species with repeated bouts of reproduction, a female's ability to retain sufficient tissue for self-maintenance is essential to her survival and capacity for future reproduction. Loss of bone mineral content results in bone fragility and the possibility of reduced survival, so females should guard against the overuse of their bone mineral during reproduction. Given these constraints, I predicted that bone mobilization would increase with litter size in mice but plateau before maximum litter size was reached. To test this idea, I manipulated the litter sizes of house mice on the day of parturition to 3, 8, 13, and 18 offspring. At weaning, I euthanized the females and calculated whole-body and bone mineral composition. The total mineral content of females' femurs dropped as litter size increased to the average litter size for this strain of mouse (13) but surprisingly, femoral mineral content was higher for females assigned the largest litter sizes (18). Seven of the nine females assigned 18 young cannibalized some of their offspring. For females assigned to these larger litters, femoral ash content was not correlated with number of young consumed, suggesting that mineral recycling had little effect on final bone mineral content. However, nursing effort (accounting for young lost to cannibalism) was correlated with maternal femoral ash at weaning. These finding suggest that the high bone mineral content of females assigned the largest litters was associated with a reduction in endogenous mineral allocated to the litter.

Biomass ash reutilisation as an additive in the composting process of organic fraction of municipal solid waste.

PubMed

Asquer, Carla; Cappai, Giovanna; De Gioannis, Giorgia; Muntoni, Aldo; Piredda, Martina; Spiga, Daniela

2017-11-01

In this work the effects of selected types of biomass ash on the composting process and final product quality were studied by conducting a 96-day long experiment where the source separated organic fraction of municipal waste, mixed with wood prunings that served as bulking agent, was added with 0%, 2%, 4% and 8% wt/wt of biomass ash. The evolution over time of the main process parameters was observed, and the final composts were characterised. On the basis of the results, both the composting process and the quality of the final product were improved by ash addition. Enhanced volatile solids reduction and biological stability (up to 32% and 52%, respectively, as compared to the unamended product) were attained when ash was added, since ash favored the aerobic degradation by acting asa physical conditioner. In the final products, higher humification of organic matter (expressed in terms of the humification index, that was 2.25 times higher in the most-enriched compost than in the unamended one) and total Ca, K, Mg and P content were observed when ash was used. The latter aspect may influence the composts marketability positively, particularly with regards to potassium and phosphorus. The heavy metals content, that is regarded as the main environmental disadvantage when using ash asa composting additive, did not negatively affect the final composts quality. However, some other controversial effects of ash, related to the moisture and temperature values attained during the process, pH (8.8-9.2 as compared to 8.2 of the unamended compost) and electrical conductivity levels (up to 53% higher as compared to the unamended compost) in the final composts, were also observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phenolic acids as bioindicators of fly ash deposit revegetation.

PubMed

Djurdjević, L; Mitrović, M; Pavlović, P; Gajić, G; Kostić, O

2006-05-01

The floristic composition, the abundance, and the cover of pioneer plant species of spontaneously formed plant communities and the content of total phenolics and phenolic acids, as humus constituents, of an ash deposit after 7 years of recultivation were studied. The restoration of both the soil and the vegetation on the ash deposits of the "Nikola Tesla-A" thermoelectric power plant in Obrenovac (Serbia) is an extremely slow process. Unfavorable physical and chemical characteristics, the toxicity of fly ash, and extreme microclimatic conditions prevented the development of compact plant cover. The abundance and cover of plants increased from the central part of the deposit towards its edges (ranging from 1-80%). Festuca rubra L., Crepis setosa Hall., Erigeron canadensis L., Cirsium arvense (L.) Scop., Calamagrostis epigeios (L.) Roth., and Tamarix gallica L. were the most abundant species, thus giving the highest cover. Humus generated during the decomposition process of plant remains represents a completely new product absent in the ash as the starting material. The amount of total phenolics and phenolic acids (38.07-185.16 microg/g of total phenolics and 4.12-27.28 microg/g of phenolic acids) in fly ash increased from the center of the deposit towards its edges in correlation with the increase in plant abundance and cover. Ash samples contained high amounts of ferulic, vanillic, and p-coumaric acid, while the content of both p-hydroxybenzoic and syringic acid was relatively low. The presence of phenolic acids indicates the ongoing process of humus formation in the ash, in which the most abundant pioneer plants of spontaneously formed plant communities play the main role. Phenolic compounds can serve as reliable bioindicators in an assessment of the success of the recultivation process of thermoelectric power plants' ash deposits.

The treatment of some low-rank coals with carbon dioxide water: Effects on slurry-relevant properties: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slegeir, W.; Sanchez, J.; Coughlan, R.

1986-09-01

This project is concerned with the results of employing CO/sub 2//H/sub 2/O treatments on two low-rank coals. The coals employed in this project were North Dakota lignite from the Indianhead Mine and Utah subbituminous from the Sufco mine. This project is concerned with changes in slurry-relevant characteristics for these low-rank coals due to such treatments. These characteristics include equilibrium moisture, ash content and composition, grindability and slurry rheology. Batch CO/sub 2//water treatments on North Dakota Indianhead lignite afforded a reduction in coal-bound moisture, affording as much as a 35% decrease in equilibrium moisture content. The resulting treated lignite also provedmore » to be a ''cleaner'' coal, with a 30 to 35% reduction in ash content. For the Utah Sufco coal, no appreciable changes in equilibrium moisture were attained and the ash contents generally only slightly reduced Sufco. However, for the more severe treatment, alkaline and alkaline earth were lowered appreciably, with a commensurate increase in ash fusion temperature. For both coals, some improvements in grindability were realized under the most severe treatment conditions (80/sup 0/C, 1200 psi). The less severe conditions afforded little changes in grindability. Some measurements taken of the rheology of treated -200 mesh Indianhead coal slurries have shown non-Newtonian behavior. These slurries settled rapidly when concentrations greater than 50% were reached, hence viscosity measurements were difficult to obtain. Although the mechanism of CO/sub 2//H/sub 2/O action on coal is not clear, the results of this project are consistent with an ion-exchange process, whereby the basic components are exchanged with the hydronium ion of the CO/sub 2//H/sub 2/O mixture. Such ion exchange may lead to other changes in the coal matrix. 38 refs., 8 figs, 18 tabs.« less

Effect of Age and Caponization on Blood Parameters and Bone Development of Male Native Chickens in Taiwan

PubMed Central

Lin, Cheng-Yung; Hsu, Jenn-Chung; Wan, Tien-Chun

2012-01-01

An experiment was carried out to determine the effect of age and caponization on the development blood and bone characteristics development in male country chickens in Taiwan. A total of two hundred 8-wk-old LRI native chicken cockerels, Taishi meat No.13 from LRI-COA, were used as experimental animals. Cockerels were surgically caponized at 8 wks of age. Twelve birds in each group were bled and dressed from 8 wks to 35 wks of age at 1 to 5 wk intervals. The results indicated that the plasma testosterone concentration was significantly (p<0.05) lower in capons after 12 wks of age (caponized treatment after 4 wks) than that of the intact males. The relative tibia weight, bone breaking strength, cortical thickness, bone ash, bone calcium, bone phosphorus and bone magnesium contents were significantly (p<0.05) higher in intact males, while capons had higher (p<0.05) plasma ionized calcium, inorganic phosphorus and alkaline phosphatase concentration. The plasma testosterone concentration, relative tibia weight, tibia length, breaking strength, cortical thickness, bone ash, calcium, and phosphorus contents of intact males chickens increased significantly (p<0.05) with the advance of age. In addition, the relative tibia weight of capons peaked at 18 wks of age, and declined at 35 wks of age. The bone ash, calcium and phosphorus content increased most after 14 wks of age in male native chickens in Taiwan. Also, tibia length and cortical thickness peaked at 22 wks of age. However, the peak of bone strength was found at 26 wks of age. These findings support the assertion that androgens can directly influence bone composition fluxes in male chickens. Caponization caused a significant increase in bone loss at 4 wks post treatment, which reflected bone cell damage, and demonstrated reductions in the relative tibia weight, breaking strength, cortical thickness, bone ash, calcium, phosphorus and magnesium contents, and increases in plasma ionized calcium, inorganic phosphorus and alkaline phosphatase concentration. PMID:25049655

Effect of secondary fuels and combustor temperature on mercury speciation in pulverized fuel co-combustion: part 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shishir P. Sable; Wiebren de Jong; Ruud Meij

2007-08-15

The present work mainly involves bench scale studies to investigate partitioning of mercury in pulverized fuel co-combustion at 1000 and 1300{sup o}C. High volatile bituminous coal is used as a reference case and chicken manure, olive residue, and B quality (demolition) wood are used as secondary fuels with 10 and 20% thermal shares. The combustion experiments are carried out in an entrained flow reactor with a fuel input of 7-8 kWth. Elemental and total gaseous mercury concentrations in the flue gas of the reactor are measured on-line, and ash is analyzed for particulate mercury along with other elemental and surfacemore » properties. Animal waste like chicken manure behaves very differently from plant waste. The higher chlorine contents of chicken manure cause higher ionic mercury concentrations whereas even with high unburnt carbon, particulate mercury reduces with increase in the chicken manure share. This might be a problem due to coarse fuel particles, low surface area, and iron contents. B-wood and olive residue cofiring reduces the emission of total gaseous mercury and increases particulate mercury capture due to unburnt carbon formed, fine particles, and iron contents of the ash. Calcium in chicken manure does not show any effect on particulate or gaseous mercury. It is probably due to a higher calcium sulfation rate in the presence of high sulfur and chlorine contents. However, in plant waste cofiring, calcium may have reacted with chlorine to reduce ionic mercury to its elemental form. According to thermodynamic predictions, almost 50% of the total ash is melted to form slag at 1300{sup o}C in cofiring because of high calcium, iron, and potassium and hence mercury and other remaining metals are concentrated in small amounts of ash and show an increase at higher temperatures. No slag formation was predicted at 1000{sup o}C. 24 refs., 8 figs., 4 tabs.« less

Phosphorus utilization in finishing broiler chickens: effects of dietary calcium and microbial phytase.

PubMed

Rousseau, X; Létourneau-Montminy, M P; Même, N; Magnin, M; Nys, Y; Narcy, A

2012-11-01

A decrease in dietary P, especially in finishing broilers (21 to 38 d old), is a crucial issue in poultry production from an environmental and economic point of view. Nevertheless, P must be considered together with other dietary components such as Ca and microbial phytase. Different corn and soybean meal-based diets varying in Ca [low (LCa) 0.37, medium (MCa) 0.57, and high (HCa) 0.77%], and nonphytate P [nPP; low (LnPP) 0.18 and high (HnPP) 0.32%] content were tested with and without microbial phytase [0 or 500 phytase units (FTU)/kg]. Feed intake, BW gain, bone mineralization, and mineral retention were examined in 144 Ross PM3 broilers (22 to 38 d old) reared in individual cages. Growth performance was not significantly affected by the treatments. Nevertheless, a numerical decrease of ADG and ADFI was observed in HCa-LnPP and LCa-HnPP associated with an increase of feed conversion ratio. Decreased dietary Ca reduced tibia ash content (Ca, linear: P < 0.001; quadratic: P = 0.034) and tibia ash weight for the highest level of nPP (Ca × nPP; P = 0.035). In parallel, increasing dietary Ca reduced the flow of retained P (P = 0.022) but also tibia ash weight in LnPP diets (Ca × nPP; P = 0.035). The responses of the animals in terms of tibia ash content and P retention were improved by the addition of microbial phytase especially for the lowest P diets (nPP × phytase, P = 0.021 and P = 0.009; respectively). Phytase increased dry tibia weight, bone breaking strength, and tibia diameter in broilers fed the highest Ca diets (Ca × phytase; P < 0.05). We conclude that is possible to decrease P levels in finishing broilers, if the Ca content is appropriate. Nevertheless, decreasing the dietary P and Ca cannot allow a maximization of bone mineralization, but the optimal threshold remains to be determined.

Influence of moisture content of combusted wood on the thermal efficiency of a boiler

NASA Astrophysics Data System (ADS)

Dzurenda, Ladislav; Banski, Adrián

2017-03-01

In the paper the influence of moisture content of wood on the heat losses and thermal efficiency of a boiler is analysed. The moisture content of wood has a negative effect, especially on flue gas loss. The mathematical dependence of the thermal efficiency of a boiler is presented for the following boundary conditions: the moisture content of wood 10-60%, range of temperatures of emitted flue gases from the boiler into the atmosphere 120-200 C, the emissions meeting the emission standards: carbon monoxide 250 mgm-3, fly ash 50 mgm-3 and the heat power range 30-100%.

Process for converting coal into liquid fuel and metallurgical coke

DOEpatents

Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

1994-01-01

A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

Postharvest conservation of the tuberous roots of Pachyrhizus Ahipa (Wedd) Parodi.

PubMed

Mussury, Rosilda M; Scalon, Silvana P Q; Silva, Magaiver A; Silva, Tatiane F; Gomes, Hellen; Gassi, Rosimeire

2013-01-01

This paper aimed to evaluate the effects of storage periods on the conservation of Pachyrhizus ahipa roots at different temperatures and packaging materials. The roots were harvested, washed, packed in PVC, plastic bags, without wrappings (control) and stored in polystyrene trays in refrigerators, or cold chambers, or at room temperature. Total titratable acidity (TTA), total soluble solids (TSS), pH, as well as their ash, lipid, total carbohydrate and protein (dry basis) contents were analyzed. The lowest loss of root fresh weight was observed in the cold chamber and plastic bags. The TTA remained higher among roots stored in the cold chamber and in PVC packaging. The lowest TSS contents were observed for roots stored in the cold chamber, and these did not vary among the packing materials. The average carbohydrate content percentage for all treatments was 84.9%. The percentage of lipids was highest in roots stored at room temperature while protein and ash contents were highest in roots under refrigeration. The best storage conditions for roots are plastic bags packaging in a cold chamber, with the roots retaining appropriate quality for commercialization for up to 30 days.

Qualitative and Quantitative Assessment of Four Marketed Formulations of Brahmi

PubMed Central

Saini, Neeti; Mathur, Rajani; Agrawal, S. S.

2012-01-01

This study was conducted with the aim to compare two batches each of four popular commercial formulations of Bacopa monnieri (Brahmi), and report, if any, inter-batch variations. The formulations were procured from local market and analyzed for label specifications, uniformity of weight of capsule, identity, purity and strength parameters (total ash content test, acid insoluble ash content, water soluble extractive, alcohol soluble extractive, loss on drying). Bacoside A, one of the pharmacologically active saponin present in B. monnieri, was quantified in all the formulations using UV-spectrophotometer. In addition each formulation was assessed and compared for variation in biological activity using in vitro test for hemolytic activity using human erythrocytes. The results of the study show that there is a wide variation in the quality and content of herbal drugs marketed by different manufacturers. More importantly this study demonstrates that there exists a bigger challenge of batch-to-batch variation in the quality and content of herbal formulations of the same manufacturer. This challenge of providing standardized formulations is being faced by not any one manufacturing house but by all, and may be attributed firstly to, lack of stringent regulations and secondly to high variability in raw material quality. PMID:23204618

Qualitative and quantitative assessment of four marketed formulations of brahmi.

PubMed

Saini, Neeti; Mathur, Rajani; Agrawal, S S

2012-01-01

This study was conducted with the aim to compare two batches each of four popular commercial formulations of Bacopa monnieri (Brahmi), and report, if any, inter-batch variations. The formulations were procured from local market and analyzed for label specifications, uniformity of weight of capsule, identity, purity and strength parameters (total ash content test, acid insoluble ash content, water soluble extractive, alcohol soluble extractive, loss on drying). Bacoside A, one of the pharmacologically active saponin present in B. monnieri, was quantified in all the formulations using UV-spectrophotometer. In addition each formulation was assessed and compared for variation in biological activity using in vitro test for hemolytic activity using human erythrocytes. The results of the study show that there is a wide variation in the quality and content of herbal drugs marketed by different manufacturers. More importantly this study demonstrates that there exists a bigger challenge of batch-to-batch variation in the quality and content of herbal formulations of the same manufacturer. This challenge of providing standardized formulations is being faced by not any one manufacturing house but by all, and may be attributed firstly to, lack of stringent regulations and secondly to high variability in raw material quality.

Characterization of Korean solid recovered fuels (SRFs): an analysis and comparison of SRFs.

PubMed

Choi, Yeon-Seok; Han, Soyoung; Choi, Hang-Seok; Kim, Seock-Joon

2012-04-01

To date, Korea has used four species of solid recovered fuels (SRFs) which have been certified by the Environmental Ministry of Korea: refuse-derived fuel (RDF), refused plastic fuel (RPF), tyre-derived fuel (TDF), and wood chip fuel (WCF). These fuels have been used in many industrial boilers. In this study, seven regulatory properties associated with each of the four species: particle size, moisture and ash content, lower heating value (LHV), total chlorine, sulfur, and heavy metals content (Pb, As, Cd, Hg, Cr) were analysed. These properties are the main regulation criteria for the usage and transfer of SRFs in Korea. Different properties of each SRF were identified on the basis of data collected over the last 3 years in Korea, and the manufacturing process problem associated with the production of SRFs were considered. It was found that the high moisture content of SRFs (especially WCF) could directly lead to the low LHV of SRFs and that the poor screening and sorting of raw materials could cause defective SRF products with high ash or chlorine contents. The information obtained from this study could contribute to the manufacturing of SRF with good quality.

Contents and occurrence of cadmium in the coals from Guizhou province, China.

PubMed

Song, Dangyu; Wang, Mingshi; Zhang, Junying; Zheng, Chuguang

2008-10-01

Eleven raw coal samples were collected from Liuzhi, Suicheng, Zunyi, Xingren, Xingyi, and Anlong districts in Guizhou Province, Southwest China. The content of cadmium (Cd) in coal was determined using inductively coupled plasma mass-spectrometry (ICP-MS). Cd contents ranged from 0.146 to 2.74 ppm (whole coal basis), with an average of 1.09 ppm. In comparison with the arithmetic means of Cd in Chinese coal (0.25 ppm), this is much higher. In order to find its occurrence in coal, float-sink analysis and a coal flotation test by progressive release were conducted on two raw coal samples. The content of the Cd and ash yield of the flotation products were determined. The organic matter was removed by low-temperature ashing (LTA). X-ray diffraction (XRD) was used to differentiate the main, minor, and trace minerals in the LTA from different flotation subproducts. Quartz, kaolinite, pyrite, and calcite were found to dominate the mineral matters, with a proportion of anatase, muscovite, and illite. Then quantitative analysis of minerals in LTA was conducted using material analysis using diffraction (MAUD) based on the Rietveld refinement method. Results show that Cd has a strong association with kaolinite.

Determination of chemical properties in 'calçot' (Allium cepa L.) by near infrared spectroscopy and multivariate calibration.

PubMed

Sans, Silvia; Ferré, Joan; Boqué, Ricard; Sabaté, José; Casals, Joan; Simó, Joan

2018-10-01

'Calçots', the immature floral stems of second-year onion resprouts, are an economically important traditional crop in Catalonia (Spain). Classical approaches to evaluating the chemical properties of 'calçots' are time consuming and expensive; near-infrared spectroscopy (NIRS) may be faster and cheaper. We used NIRS to develop partial least square (PLS) models to predict dry matter, soluble solid content, titratable acidity, and ash content in cooked 'calçots'. To guarantee the robustness of the models, calibration samples were grown and analyzed in a first season (2014-15) and validation samples in a second season (2015-16). NIRS on puree spectra estimated dry matter and soluble solid content with excellent accuracy (R 2 pred  = 0.953, 0.985 and RPD = 4.571, 8.068, respectively). However, good estimation of titratable acidity and ash content required using ground dried puree spectra (R 2 pred  = 0.852, 0.820 and RPD = 2.590, 1.987, respectively). NIRS can be a helpful tool for 'calçots' breeding and quality control. Copyright © 2018 Elsevier Ltd. All rights reserved.

Leaching characteristics of rare metal elements and chlorine in fly ash from ash melting plants for metal recovery.

PubMed

Jung, Chang-Hwan; Osako, Masahiro

2009-05-01

In terms of resource recovery and environmental impact, melting furnace fly ash (MFA) is attracting much attention in Japan due to its high metal content. The study aims to obtain fundamental information on using a water extraction method not only to concentrate valuable rare metals but also to remove undesirable substances such as chlorine for their recovery from MFA. The composition and leaching characteristics of MFA was investigated. The results revealed that the metal content in MFA is nearly equal to raw ore quality. The content of Ag, In, Pd, Pb, and Zn is, in fact, higher than the content of raw ore. As for leaching behavior, Ag, Bi, In, Ga, Ge, Sb, Sn, and Te showed the lowest release at a neutral pH range. Pd was leached constantly regardless of pH, but its concentration was quite low. On the other hand, most of the Tl was easily leached, revealing that water extraction is not appropriate for Tl recovery from MFA. Major elements Cl, Ca, Na, and K, occupying about 70% of MFA, were mostly leached regardless of pH. Base metal elements Cu, Pb, and Zn showed minimum solubility at a neutral pH. The leaching ratio of target rare metal elements and base metal elements suggests that the optimal pH for water extraction is 8-10, at which the leaching concentration is minimized. The water extraction process removed most of the Cl, Ca, Na, and K, and the concentration of rare metals and base metals increased by four or five times.

Bleaching effects of massecuite on some properties of crystallized sugar beet and milk chocolate bars produced.

PubMed

Sadjadi, F Seyed; Honarvar, M; Kalbasi-Ashtari, A; Motaghian, P

2018-04-01

Four kinds of bleached, unbleached, second and third crystal sugars (BCS, UCS, SCS and TCS) were made from different massecuites in a sugar-beet factory, and their physiochemical (polarization, invert sugar, colorants, pH, ash and SO 2 ), microbiological and functional properties were measured. While the polarization of UCS, SCS and TCS were lower than BCS; their invert sucrose, colorants, pH and ash contents were significantly higher than BCS. The phenols and betaine of BCS, UCS, SCS, and TCS were 144, 401, 384 and 673 (mg/100 g); and 244, 791, 4662, and 6589 (mg/100 g); respectively. Whereas the phenol of milk chocolate bars (MCB) made with UCS, SCS, and TCS were only 10% higher than MCB completed with BCS; their betaine contents were substantially (up to 16 times) higher than the ones finished with BCS. Sensory evaluation showed that the MCB prepared with three sugars including UCS, SCS and TCS had significantly higher glossiness, brittleness, flavor and mouth feel than those made with BCS. The greater colorants, ash content and inverted sugars of UCS, SCS and TCS (in comparison with BCS) made considerable improvements in the glossiness, flavor and brittleness of MCB, respectively. BCS had 8 ppm of toxic sulfur; whereas, UCS, SCS and TCS had no detectable sulfur and significantly higher beneficial copper content than BCS. No pathogenic microorganism were detected in UCS, SCS, TCS or their subsequent MCB. Our results highly recommend using UCS, SCS and TCS instead of BCS in food products (such as MCB) due to their higher health benefits.

Proximate body composition and energy content of plaice ( Pleuronectes platessa) in relation to the condition factor

NASA Astrophysics Data System (ADS)

Costopoulos, C. G.; Fonds, M.

Length, wet weight, dry weight, and the content of lipid, ash and protein of young plaice were determined. The energy content of the fish was estimated by multiplying lipid and protein content by the commonly used calorific equivalents. The data were sorted from low to high condition factor of the fish and grouped according to condition factor (K = 100·W·L -3) into 8 condition groups. Mean values of percentage body composition and energy content were calculated for each condition group. Equations giving the best fit between condition factor and the parameters of body composition and energy content are presented. From the decrease in condition factor in fasting fish the relative losses of lipid and protein energy are calculated. The accuracy of equations for the calculation of energy content of plaice from condition factor is discussed.

[Predicting low NOx combustion property of a coal-fired boiler].

PubMed

Zhou, Hao; Mao, Jianbo; Chi, Zuohe; Jiang, Xiao; Wang, Zhenhua; Cen, Kefa

2002-03-01

More attention was paid to the low NOx combustion property of the high capacity tangential firing boiler, but the NOx emission and unburned carbon content in fly ash of coal burned boiler were complicated, they were affected by many factors, such as coal character, boiler's load, air distribution, boiler style, burner style, furnace temperature, excess air ratio, pulverized coal fineness and the uniformity of the air and coal distribution, etc. In this paper, the NOx emission property and unburned carbon content in fly ash of a 600 MW utility tangentially firing coal burned boiler was experimentally investigated, and taking advantage of the nonlinear dynamics characteristics and self-learning characteristics of artificial neural network, an artificial neural network model on low NOx combustion property of the high capacity boiler was developed and verified. The results illustrated that such a model can predicate the NOx emission concentration and unburned carbon content under various operating conditions, if combined with the optimization algorithm, the operator can find the best operation condition of the low NOx combustion.

Seasonal variation of chemical composition and biomethane production from the brown seaweed Ascophyllum nodosum.

PubMed

Tabassum, Muhammad Rizwan; Xia, Ao; Murphy, Jerry D

2016-09-01

Ascophyllum nodosum, an abundant Irish brown seaweed, shows significant seasonal variation in chemical composition and biogas production. The polyphenol content is shown to be a more important factor in biogas production than ash content. High polyphenol content in summer months adversely affected biogas production; suggesting two potential harvest dates, March and October. A. nodosum harvested in October showed a relatively low level of polyphenols (2% of TS) and ash (23% of volatile solids), and exhibited a specific methane yield of 215LCH4kgVS(-1), which was 44% of theoretical yield. The highest yield per wet weight of 47m(3)CH4t(-1) was achieved in October, which is 2.9 times higher than the lowest value (16m(3)CH4t(-1)), obtained in December. The gross energy yield of A. nodosum based on the optimal biogas production can achieve 116GJha(-1)yr(-1) in October. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Study on quality standards of decoction pieces of salt Alpinia].

PubMed

Li, Wenbing; Hu, Changjiang; Long, Lanyan; Huang, Qinwan; Xie, Xiuqiong

2010-12-01

To establish the quality criteria for decoction pieces of salt Alpinia. Decoction pieces of salt Alpinia were measured with moisture, total ash, acid-insoluble ash, water-extract and volatile oils according to the procedures recorded in the Chinese Pharmacopoeia 2010. The content of Nootkatone was determined by HPLC, and NaCl, by chloridion electrode method. We obtained results of total ash, acid-insoluble ash, water-extract and volatile oils of 10 batches of decoction pieces of salt Alpinia moisture; Meanwhile we set the HPLC and chloridion electrode method. This research established a fine quality standard for decoction pieces of salt Alpinia.

USSR Report, Engineering and Equipment

DTIC Science & Technology

1986-08-13

JlHHHpoM H racHTeJiex B JIHHHK Ha- THeTaHH« aa racHTe/iew (ycpeAKeHHCx1 3Ha" ;:’ HHO ) i. \\ TpyOa-racHTcnb 400 MM {puc~ 4) =2,5 MTIa...reliable operation of fly-ash collectors in the period between overhauls of boilers . The walls of the modernized fly-ash collectors, in spite of...capacity of boiler , t/h Reduced ash content of fuel, %/ /(MJ/kg) [Continued on following page] Mixture of Donetsk coal 608-612 1.3-1.45 18

Adding worms during composting of organic waste with red mud and fly ash reduces CO2 emissions and increases plant available nutrient contents.

PubMed

Barthod, J; Rumpel, C; Calabi-Floody, M; Mora, M-L; Bolan, N S; Dignac, M-F

2018-09-15

Alkaline industrial wastes such as red mud and fly ash are produced in large quantities. They may be recycled as bulking agent during composting and vermicomposting, converting organic waste into soil amendments or plant growth media. The aim of this study was to assess the microbial parameters, greenhouse gas emissions and nutrient availability during composting and vermicomposting of household waste with red mud and fly ash 15% (dry weight). CO 2 , CH 4 and N 2 O emissions were monitored during 6 months in controlled laboratory conditions and microbial biomass and phospholipid acids, N and P availability were analysed in the end-products. Higher CO 2 emissions were observed during vermicomposting compared to composting. These emissions were decreased by red mud addition, while fly ash had no effect. Nitrate (NO 3 -N) content of the end-products were more affected by worms than by alkaline materials, while higher ammonium (NH 4 -N) contents were recorded for composts than vermicomposts. Red mud vermicompost showed higher soluble P proportion than red mud compost, suggesting that worm presence can counterbalance P adsorption to the inorganic matrix. Final composts produced with red mud showed no harmful heavy metal concentrations. Adding worms during composting thus improved the product nutrient availability and did not increase metal toxicity. From a practical point of view, this study suggests that for carbon stabilisation and end-product quality, the addition of red mud during composting should be accompanied by worm addition to counterbalance negative effects on nutrient availability. Copyright © 2018. Published by Elsevier Ltd.

DEVELOPMENT, TESTING, AND DEMONSTRATION OF AN OPTIMAL FINE COAL CLEANING CIRCUIT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven R. Hadley; R. Mike Mishra; Michael Placha

1999-01-27

The objective of this project was to improve the efficiency of the fine coal froth flotation circuit in commercial coal preparation plants. The plant selected for this project, Cyprus Emerald Coal Preparation Plant, cleans 1200-1400 tph of Pittsburgh seam raw coal and uses conventional flotation cells to clean the minus 100-mesh size fraction. The amount of coal in this size fraction is approximately 80 tph with an average ash content of 35%. The project was carried out in two phases. In Phase I, four advanced flotation cells, i.e., a Jameson cell, an Outokumpu HG tank cell, an open column, andmore » a packed column cell, were subjected to bench-scale testing and demonstration. In Phase II, two of these flotation cells, the Jameson cell and the packed column, were subjected to in-plant, proof-of-concept (POC) pilot plant testing both individually and in two-stage combination in order to ascertain whether a two-stage circuit results in lower levelized production costs. The bench-scale results indicated that the Jameson cell and packed column cell would be amenable to the single- and two-stage flotation approach. POC tests using these cells determined that single-stage coal matter recovery (CMR) of 85% was possible with a product ash content of 5.5-7%. Two-stage operation resulted in a coal recovery of 90% with a clean coal ash content of 6-7.5%. This compares favorably with the plant flotation circuit recovery of 80% at a clean coal ash of 11%.« less

Influence of fungi associated with bananas on nutritional content during storage.

PubMed

Odebode, A C; Sanusi, J

1996-06-01

Botryodiplodia theobromae, Rhizopus oryzae, Aspergillus niger, A. flavus and Fusarium equiseti were found to be associated with the ripening of bananas and also caused rot during storage. Bananas stored in baskets with ash fire wood ripened 2-3 days earlier than bananas stored in fibre sacks and under constant light. The infected bananas showed a decrease in the quantity of total soluble sugars, protein, lipid, crude fibre, ash, ascorbic acid and mineral elements when compared with the control fruit. Paper chromatographic studies showed the presence of glucose, sucrose, fructose, maltose and raffinose in healthy control fruit, while only sucrose appeared during storage in bananas infected with B. theobromae. The total soluble sugar and crude protein contents increased during ripening.

Production of MHD fluid

DOEpatents

Lacey, James J.; Kurtzrock, Roy C.; Bienstock, Daniel

1976-08-24

A hot gaseous fluid of low ash content, suitable for use in open-cycle MHD (magnetohydrodynamic) power generation, is produced by means of a three-stage process comprising (1) partial combustion of a fossil fuel to produce a hot gaseous product comprising CO.sub.2 CO, and H.sub.2 O, (2) reformation of the gaseous product from stage (1) by means of a fluidized char bed, whereby CO.sub.2 and H.sub.2 O are converted to CO and H.sub.2, and (3) combustion of CO and H.sub.2 from stage (2) to produce a low ash-content fluid (flue gas) comprising CO.sub.2 and H.sub.2 O and having a temperature of about 4000.degree. to 5000.degree.F.

The micromechanics model analysis of the viscosity regulation of ultra-high strength concrete with low viscosity

NASA Astrophysics Data System (ADS)

Zhu, M.; Wang, F. G.; Wang, F. Z.; Liu, Y. P.

2017-02-01

The plastic viscosity of mortar and concrete with different binder content, sand ratio, water-binder ratio, microbead dosage and different class and dosage of fly ash were tested and calculated according tomicromechanics model proposed by A. Ghanbari and B.L. Karihaloo, The correlations between these parameters and fresh concrete workability were also investigated, which showed i. high consistence with the objective reality. When binder content, microbead dosage, fly ash dosage or the water-binder ratio was increased or sand ratio was reduced, the fresh concrete viscosity would decrease correspondingly. However their effects were not that same. The relationships between T50 a, V-funnel and inverted slump time with fresh concrete viscosity were established, respectively.

Formalized classification of moss litters in swampy spruce forests of intermontane depressions of Kuznetsk Alatau

NASA Astrophysics Data System (ADS)

Efremova, T. T.; Avrova, A. F.; Efremov, S. P.

2016-09-01

The approaches of multivariate statistics have been used for the numerical classification of morphogenetic types of moss litters in swampy spruce forests according to their physicochemical properties (the ash content, decomposition degree, bulk density, pH, mass, and thickness). Three clusters of moss litters— peat, peaty, and high-ash peaty—have been specified. The functions of classification for identification of new objects have been calculated and evaluated. The degree of decomposition and the ash content are the main classification parameters of litters, though all other characteristics are also statistically significant. The final prediction accuracy of the assignment of a litter to a particular cluster is 86%. Two leading factors participating in the clustering of litters have been determined. The first factor—the degree of transformation of plant remains (quality)—specifies 49% of the total variance, and the second factor—the accumulation rate (quantity)— specifies 26% of the total variance. The morphogenetic structure and physicochemical properties of the clusters of moss litters are characterized.

Self-cementitious properties of fly ashes from CFBC boilers co-firing coal and high-sulphur petroleum coke

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng Guanghong; Li Qin; Zhai Jianping

2007-06-15

Self-cementitious properties of fly ash from circulating fluidized bed combustion boiler co-firing coal and high-sulphur petroleum coke (CPFA) were investigated. CPFA was self-cementitious which was affected by its fineness and chemical compositions, especially the contents of SO{sub 3} and free lime (f-CaO). Higher contents of SO{sub 3} and f-CaO were beneficial to self-cementitious strength; the self-cementitious strength increases with a decrease of its 45 {mu}m sieve residue. The expansive ratio of CPFA hardened paste was high because of generation of ettringite (AFt), which was influenced by its water to binder ratio (W/A), curing style and grinding of the ash. Themore » paste cured in water had the highest expansive ratio, and grinding of CPFA was beneficial to its volume stability. The hydration products of CPFA detected by X-ray diffraction (XRD) and scanning electron microscopy (SEM) were portlandite, gypsum, AFt and hydrated calcium silicate (C-S-H)« less

Cristobalite in volcanic ash of the soufriere hills volcano, montserrat, british west indies

PubMed

Baxter; Bonadonna; Dupree; Hards; Kohn; Murphy; Nichols; Nicholson; Norton; Searl; Sparks; Vickers

1999-02-19

Crystalline silica (mostly cristobalite) was produced by vapor-phase crystallization and devitrification in the andesite lava dome of the Soufriere Hills volcano, Montserrat. The sub-10-micrometer fraction of ash generated by pyroclastic flows formed by lava dome collapse contains 10 to 24 weight percent crystalline silica, an enrichment of 2 to 5 relative to the magma caused by selective crushing of the groundmass. The sub-10-micrometer fraction of ash generated by explosive eruptions has much lower contents (3 to 6 percent) of crystalline silica. High levels of cristobalite in respirable ash raise concerns about adverse health effects of long-term human exposure to ash from lava dome eruptions.

Influence of within year treatments and between year environmental differences on peach leaf ash and carbon isotopic discrimination responses

USDA-ARS?s Scientific Manuscript database

Plant ash content is related to water use efficiency (WUE) (dry matter accumulation per unit of transpiration) and Delta 13C in a range of C3 species. In breeding programs, the genetic x environment interaction is measured with multiple locations and multiple years of evaluation but the genetic x e...

Effect of water washing on the thermal behavior of rice straw.

PubMed

Said, N; Bishara, T; García-Maraver, A; Zamorano, M

2013-11-01

Rice straw can be used as a renewable fuel for heat and power generation. It is a viable mean of replacing fossil fuels and preventing pollution caused by open burning, especially in the areas where this residual biomass is generated. Nevertheless, the thermal conversion of rice straw can cause some operating problems such as slag formation, which negatively affects thermal conversion systems. So, the main objective of this research is studying the combustion behavior of rice straw samples collected from various regions by applying thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). In addition, the thermal behavior of ashes from rice straw was also analyzed in order to detect their melting points, and ash sintering was detected at different temperatures within the range between 550 and 1000°C. Since washing rice straw with water could reduce the content of undesirable inorganic compounds related to the ash fusibility, samples of washed rice straw were analyzed under combustion conditions to investigate its differences regarding the thermal behavior of rice straw. The results showed that rice straw washing led to a significant improvement in its thermal behavior, since it reduced the ash contents and sintering formation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Can washing-pretreatment eliminate the health risk of municipal solid waste incineration fly ash reuse?

PubMed

Wang, Yao; Pan, Yun; Zhang, Lingen; Yue, Yang; Zhou, Jizhi; Xu, Yunfeng; Qian, Guangren

2015-01-01

Although the reuse of washing-pretreated MSWI fly ash bas been a hot topic, the associated risk is still an issue of great concern. The present study investigated the influence of washing-pretreatment on the total contents and bioaccessibility of heavy metals in MSWI fly ash. Furthermore, the study incorporated bioaccessibility adjustment into probabilistic risk assessment, to quantify the health risk from multi-pathway exposure to the concerned chemicals as a result of reusing washed MSWI fly ash. The results revealed that both water-washing and acid-washing process have resulted in the concentrated heavy metal content, and have reduced the bioaccessibility of heavy metals. Besides, the acid-washing process increased the cancer risk in most cases, while the effect of water-washing process was uncertain. However, both water-washing and acid-washing pretreatment could decrease the hazard index based on bioaccesilbility. Despite the uncertainties accompanying these procedures, the results indicated that, in this application scenario, only water-washing or acid-washing process cannot reduce the actual risk from all samples to acceptable level, especially for cancer risk. Copyright © 2014. Published by Elsevier Inc.

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

PubMed

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Development of a sintering process for recycling oil shale fly ash and municipal solid waste incineration bottom ash into glass ceramic composite.

PubMed

Zhang, Zhikun; Zhang, Lei; Li, Aimin

2015-04-01

Oil shale fly ash and municipal solid waste incineration bottom ash are industrial and municipal by-products that require further treatment before disposal to avoid polluting the environment. In the study, they were mixed and vitrified into the slag by the melt-quench process. The obtained vitrified slag was then mixed with various percentages of oil shale fly ash and converted into glass ceramic composites by the subsequent sintering process. Differential thermal analysis was used to study the thermal characteristics and determine the sintering temperatures. X-ray diffraction analysis was used to analyze the crystalline phase compositions. Sintering shrinkage, weight loss on ignition, density and compressive strength were tested to determine the optimum preparation condition and study the co-sintering mechanism of vitrified amorphous slag and oil shale fly ash. The results showed the product performances increased with the increase of sintering temperatures and the proportion of vitrified slag to oil shale fly ash. Glass ceramic composite (vitrified slag content of 80%, oil shale fly ash content of 20%, sintering temperature of 1000 °C and sintering time of 2h) showed the properties of density of 1.92 ± 0.05 g/cm(3), weight loss on ignition of 6.14 ± 0.18%, sintering shrinkage of 22.06 ± 0.6% and compressive strength of 67 ± 14 MPa. The results indicated that it was a comparable waste-based material compared to previous researches. In particular, the energy consumption in the production process was reduced compared to conventional vitrification and sintering method. Chemical resistance and heavy metals leaching results of glass ceramic composites further confirmed the possibility of its engineering applications. Copyright © 2015 Elsevier Ltd. All rights reserved.

Leaching characteristics of solid wastes from thermal power plants of western Turkey and comparison of toxicity methodologies.

PubMed

Baba, Alper; Kaya, Abidin

2004-11-01

Use of lignite in power generation has led to increasing environmental problems associated not only with gaseous emissions, but also with the disposal of ash residues. In particular, use of low quality coals with high ash content results in huge quantities of both fly and bottom ashes to be disposed of. A main problem related to coal ash disposal is the heavy metal content of the residue. In this regard, experimental results of numerous studies indicate that toxic trace metals may leach when fly and bottom ashes are in contact with water. In this study, fly and bottom ash samples obtained from thermal power plants, namely Yenikoy, Kemerkoy and Yatagan, located at the southwestern coast of Turkey, were subjected to toxicity tests such as the extraction (EP) and toxicity characteristic leaching (TCLP) procedures of the US Environmental Protection Agency (USEPA) and the so-called 'Method A' extraction procedure of the American Society of Testing and Material (ASTM). The geochemical composition of ash samples showed variations depending on the coal burned in the plants. Furthermore, the EP, TCLP and ASTM toxicity tests showed variations such that the ash samples were classified as 'toxic waste' based on EP and TCLP results whereas they were classified as 'non-toxic' based on ASTM results, indicating test results are pH dependent. When the extraction results were compared with the chemical composition of water samples obtained in the vicinity of the thermal power plants, it was found that the results obtained using the ASTM procedure cannot be used to predict subsurface contamination whereas the EP and TCLP procedures can be used.

Reference data set of volcanic ash physicochemical and optical properties

NASA Astrophysics Data System (ADS)

Vogel, A.; Diplas, S.; Durant, A. J.; Azar, A. S.; Sunding, M. F.; Rose, W. I.; Sytchkova, A.; Bonadonna, C.; Krüger, K.; Stohl, A.

2017-09-01

Uncertainty in the physicochemical and optical properties of volcanic ash particles creates errors in the detection and modeling of volcanic ash clouds and in quantification of their potential impacts. In this study, we provide a data set that describes the physicochemical and optical properties of a representative selection of volcanic ash samples from nine different volcanic eruptions covering a wide range of silica contents (50-80 wt % SiO2). We measured and calculated parameters describing the physical (size distribution, complex shape, and dense-rock equivalent mass density), chemical (bulk and surface composition), and optical (complex refractive index from ultraviolet to near-infrared wavelengths) properties of the volcanic ash and classified the samples according to their SiO2 and total alkali contents into the common igneous rock types basalt to rhyolite. We found that the mass density ranges between ρ = 2.49 and 2.98 g/cm3 for rhyolitic to basaltic ash types and that the particle shape varies with changing particle size (d < 100 μm). The complex refractive indices in the wavelength range between λ = 300 nm and 1500 nm depend systematically on the composition of the samples. The real part values vary from n = 1.38 to 1.66 depending on ash type and wavelength and the imaginary part values from k = 0.00027 to 0.00268. We place our results into the context of existing data and thus provide a comprehensive data set that can be used for future and historic eruptions, when only basic information about the magma type producing the ash is known.

Important properties of bamboo pellets to be used as commercial solid fuel in China

Treesearch

Zhijia Liu; Benhua Fei; Zehui Jiang; Zhiyong Cai; Xing' e Liu

2014-01-01

Bamboo is a type of biomass material and has great potential as a bioenergy resource of the future in China. Some properties of bamboo pellets, length, diameter, moisture content (MC), particle density, bulk density, durability, fine content, ash, gross calorific value, combustion rate and heat release rate, were determined and the effects of MC and particle size (PS)...

Low Dose Food Irradiation at Natick

DTIC Science & Technology

1977-06-01

bread, cakes, and cookies made with this irradiated flour have consistently received excellent ratings by taste panelists and other consumers at Natick...activity, titratable acidity, pH, ash, protein, and moisture content), dough and baking characteristics (bread scores, rheological and alpha-amylase...on the vitamin content in the irradiated flour or in the bread made from the 1 3See footnote 5 15 flour (Tables 10,11). Farinographs, dough

Estimates of soil ingestion by wildlife

USGS Publications Warehouse

Beyer, W.N.; Connor, E.E.; Gerould, S.

1994-01-01

Many wildlife species ingest soil while feeding, but ingestion rates are known for only a few species. Knowing ingestion rates may be important for studies of environmental contaminants. Wildlife may ingest soil deliberately, or incidentally, when they ingest soil-laden forage or animals that contain soil. We fed white-footed mice (Peromyscus leucopus) diets containing 0-15% soil to relate the dietary soil content to the acid-insoluble ash content of scat collected from the mice. The relation was described by an equation that required estimates of the percent acid-insoluble ash content of the diet, digestibility of the diet, and mineral content of soil. We collected scat from 28 wildlife species by capturing animals, searching appropriate habitats for scat, or removing material from the intestines of animals collected for other purposes. We measured the acid-insoluble ash content of the scat and estimated the soil content of the diets by using the soil-ingestion equation. Soil ingestion estimates should be considered only approximate because they depend on estimated rather than measured digestibility values and because animals collected from local populations at one time of the year may not represent the species as a whole. Sandpipers (Calidris spp.), which probe or peck for invertebrates in mud or shallow water, consumed sediments at a rate of 7-30% of their diets. Nine-banded armadillo (Dasypus novemcinctus, soil = 17% of diet), American woodcock (Scolopax minor, 10%), and raccoon (Procyon lotor, 9%) had high rates of soil ingestion, presumably because they ate soil organisms. Bison (Bison bison, 7%), black-tailed prairie dog (Cynomys ludovicianus, 8%), and Canada geese (Branta canadensis, 8%) consumed soil at the highest rates among the herbivores studied, and various browsers studied consumed little soil. Box turtle (Terrapene carolina, 4%), opossum (Didelphis virginiana, 5%), red fox (Vulpes vulpes, 3%), and wild turkey (Meleagris gallopavo, 9%) consumed soil at intermediate rates. Ingested soil may be the principal means of exposure to some environmental contaminants or the principal source of certain minerals. Soil-ingestion estimates may be required for risk assessments of wildlife inhabiting contaminated sites and for computing budgets of those nutrients associated mainly with soil.

Trace element geochemistry of altered volcanic ash layers (tonsteins) in late Permian coal-bearing formations of eastern Yunnan and western Guizhou Provinces, China

USGS Publications Warehouse

Zhou, Y.; Bohor, B.F.; Ren, Y.

2000-01-01

Trace element compositions were determined (by instrumental neutron activation analysis; INAA) in 30 samples of synsedimentary volcanic ash-derived tonsteins and detrital claystones from coal seams within the late Permian coal-bearing formation of eastern Yunnan and western Guizhou Provinces, China. The characteristics of trace-element geochemistry in the tonsteins can be distinguished from those of detrital claystones because of the former's unique volcanic-ash origin. The detrital claystones are characterized by their relatively high content of V, Ti, Sc, Cr, Co and Ni, relatively low content of Th and U, Th/U ratio, and small negative Eu anomaly (Eu/Eu* 0.63-0.93). Overall, these trace element characteristics are consistent with a mafic source similar to the composition of basalt rocks in the erosional region on the western edge of the study area. In contrast, the tonsteins are low in V, Ti, Sc, Cr, Co and Ni contents and have a high Th/U ratio with a distinct negative Eu anomaly (Eu/Eu* normally in the range of 0.2-0.4), consistent with a silicic magmatic source. Within the group of tonsteins, those from the lower section (P2.1) of the coal-bearing formation are relatively high in Ti, Zr, Hf, Nb, Ta and rare earth elements (REE), as compared to those from the middle and upper sections (P2.2+3). In trace-element discrimination diagrams (scatter plots) of Hf-Ta, Ti-Ta, Ti-V, Hf-Sc, Lu-Hf and Lu-Th, tonsteins from the P2.1 horizon always fall in isolated distribution areas, separate from the tonsteins of the P2.2+3 horizon. These results suggest that the source materials of tonsteins from the two separate horizons were probably derived from volcanic ash falls of two distinctly different natures. Based on a comparison of the concentrations and assemblages of trace elements between various magmatic rocks, the source materials of tonsteins from P2.1 horizon were mostly composed of calc-alkalic, silica-poor volcanic ash (similar to rhyodacitic magma), whereas those from P2.+3 were apparently more siliceous and K-rich (rhyolitic magma). Thus, tonsteins from the two different horizons are characterized by unique geochemical properties, which remain constant over a wide lateral extent. Integration of trace-elemental compositions with mineralogical and textural observations makes possible the establishment of tonstein stratigraphy, thus, facilitating more precise and reliable coal-seam correlations. (C) 2000 Elsevier Science B.V. All rights reserved.Trace element compositions were determined in 30 samples of synsedimentary volcanic ash-derived tonsteins and detrital claystones from coal seams within the late Permian coal-bearing formation of eastern Yunnan and western Guizhou Provinces, China. The characteristics of trace-element geochemistry in the tonsteins can be distinguished from those of detrital claystones because of the former's unique volcanic-ash origin. The detrital claystones are characterized by their relatively high content of V, Ti, Sc, CR, Co and Ni, relatively low content of Th and U, Th/U ratio, and small negative Eu anomaly.

Evaluation of dietary calcium level and source and phytase on growth performance, serum metabolites, and ileum mineral contents in broiler chicks fed adequate phosphorus diets from one to 28 days of age.

PubMed

Momeneh, T; Karimi, A; Sadeghi, G; Vaziry, A; Bedford, M R

2018-04-01

A total of 936 one-day-old broiler chicks (Ross 308) was used to evaluate the effects of dietary calcium (Ca) source (1.0 and 0.6% from Ca carbonate [CC], or 0.6% from Celtic sea minerals [CSM]) on broiler chick response to phytase supplementation (0, 500, or 2,500 FTU per kg of diet) in phosphorus (P) adequate diets. Birds were randomly assigned to 9 treatments, each replicated 8 times (4 repeats of male and 4 repeats of female birds; 13 birds per replicate) in a completely randomized design. Results showed that birds fed low Ca CC diets had significantly (P ≤ 0.05) lower body weight at 14 and 21 d; weight gain during 1 to 14 d; feed intake during 1 to 14 d and 1 to 28 d; and toe and tibia ash content, ileum ash, and Ca, and P contents at 28 days. Feed conversion ratio and feed intake between 21 and 28 d, and serum Ca, Fe, and alkaline phosphatase levels at 28 d of age were not affected by dietary Ca level. The negative influence of reducing the dietary Ca level on body weight and weight gain was less severe when CC was replaced with CSM, and birds fed the CSM diet had a significantly lower feed conversion ratio and higher tibia P content compared to CC. Phytase did not have a significant influence (P > 0.05) on most measured parameters, but significantly reduced ileum P and ash contents, especially at the higher level of 2,500 vs. 500 units of phytase per kg of diet. These results confirm that CSM has a valuable potential to improve feed conversion ratio, and that phytase was less effective in compensating for a significantly reduced dietary Ca level as it is for P.

Influence of phytase added to a vegetarian diet on bone metabolism in pregnant and lactating sows.

PubMed

Liesegang, A; Loch, L; Bürgi, E; Risteli, J

2005-01-01

The purpose of the study was to find out if the supplementation of phytase to a diet of gestating and lactating sows has any effects on performance and bone parameters of the animals. Forty primiparous gilts were assigned into four groups: group A with phytase [4.2 g total phosphorus (P)/kg (gestation) and 4.5 g total P/kg (lactation)], group B without phytase (with phytase supplementation in diet for rearing) and same P content as group A, group C without phytase and higher P contents [5.0 g total P/kg (gestation) and 5.5 g total P/kg (lactation)] and group D with the same diet as group B (no phytase during the rearing). A 6-phytase was used in this trial (750 FTU/kg diet). The four diets were fed during gestation and lactation. Faeces were collected to determine apparent digestibility of minerals. Blood samples were taken to analyse minerals and bone markers. After weaning the sows were slaughtered and the bones of one hind leg were prepared to measure bone mineral density (BMD) and bone mineral content (BMC) of the tibia. Bone ash and mineral content of the phalanx III were determined. Mean P concentrations in serum decreased during gestation and lactation. But there were no significant differences between the groups. Bone formation marker bone-specific alkaline phosphatase decreased at the beginning of lactation whereas bone resorption marker serum crosslaps increased. The BMD and BMC of the tibia were slightly higher in the groups fed higher concentrations of P and phytase. The ash and mineral contents of the phalanx were the highest for the group fed the highest concentration of P. The apparent digestibility of P increased during gestation mostly in group A (57%--> 69%). In conclusion, high P content and addition of phytase to the diet induced a slightly higher ash content of the bones. It is of high importance, that sows during gestation absorb enough P, to avoid lamenesses and sudden fractures. As not many studies with phytase have been performed during gestation and lactation in sows yet, we can recommend, that phytase as supplement can be used to keep P in the diet at a lower level without negative consequences for bone health.

Possibilities of municipal solid waste incinerator fly ash utilisation.

PubMed

Hartmann, Silvie; Koval, Lukáš; Škrobánková, Hana; Matýsek, Dalibor; Winter, Franz; Purgar, Amon

2015-08-01

Properties of the waste treatment residual fly ash generated from municipal solid waste incinerator fly ash were investigated in this study. Six different mortar blends with the addition of the municipal solid waste incinerator fly ash were evaluated. The Portland cement replacement levels of the municipal solid waste incinerator fly ash used were 25%, 30% and 50%. Both, raw and washed municipal solid waste incinerator fly ash samples were examined. According to the mineralogical composition measurements, a 22.6% increase in the pozzolanic/hydraulic properties was observed for the washed municipal solid waste incinerator fly ash sample. The maximum replacement level of 25% for the washed municipal solid waste incinerator fly ash in mortar blends was established in order to preserve the compressive strength properties. Moreover, the leaching characteristics of the crushed mortar blend was analysed in order to examine the immobilisation of its hazardous contents. © The Author(s) 2015.

The study of the burning possibilities of solid combustibles in the determined conditions for complete usage of caloric [energy] and ashes resulted

DOE Office of Scientific and Technical Information (OSTI.GOV)

Voina, N.I.; Barca, F.; Mogos, D.

1995-12-31

In modern combustors, 95--98% of the organic mass of a solid combustible is converted into caloric energy; 2--4% remain in the fly ash captured in electrofilters and hydraulically removed in most cases. The 2--4% unburned materials in fly ash, together with the water from being hydraulically transported, make it difficult for the use of the fly ash for metal extraction or as a binder in the materials industry. This work presents the research results of a study in which the burning process was modified to result in fly ash without carbon content and fly ash removal by dry capture. Laboratorymore » fluidized-bed combustion of lignite with and without addition of limestone for sulfur capture was used to generate ashes for further study. The ashes were studied for their use as binders and as a cement substitute.« less

Volcanic Ash fall Impact on Vegetation, Colima 2005

NASA Astrophysics Data System (ADS)

Garcia, M. G.; Martin, A.; Fonseca, R.; Nieto, A.; Radillo, R.; Armienta, M.

2007-05-01

An ash sampling network was established arround Colima Volcano in 2005. Ash fall was sampled on the North, Northeast, East, Southeast, South, Southwest and West of the volcano. Samples were analyzed for ash components, geochemistry and leachates. Ash fall ocurred on April (12), May (10, 23), June (2, 6, 9, 10, 12, 14), July (27), September (27), October (23) and November (24). Most of the ash is made of andesitic dome-lithics but shows diferences in crystal, juvenile material and lithic content. In May, some samples contained grey and dark pumice (scoria). Texture varies from phi >4 to phi 0. Leachate concentration were low: SO4 (7.33-54.19) Cl- (2.29-4.97) and F- (0.16-0.37). During 2005, Colima Volcano's ash fall rotted some of the guava and peach fruits and had a drying effect on spearment and epazote plants. Even these small ash amounts could have hindered sugar cane and agave growth.

Clay Stabilization Using the Ash of Mount Sinabung in Terms of the Value of California Bearing Ratio (CBR)

NASA Astrophysics Data System (ADS)

Hastuty, I. P.; Roesyanto, R.; Napitupulu, S. M. A.

2018-02-01

Most areas in Indonesia consist of clay soils with high plasticity so that to meet technical requirements the soil needs improvement, which is known as soil stabilization.There are three ways of soil stabilization process, i.e. mechanical, physical and chemical. In this study, chemical stabilization was performed, that was by adding stabilizing agents to the soil. The stabilizing agent used was the ash of Mount Sinabung. Since 2010 until now, Sinabung Mountain is still experiencing eruption that produces a lot of volcanic ash and it inconveniences the environment. So, it is expected that this research will be able to optimize the utilization of Sinabung ash. The purpose of this study was to investigate the effect of the addition of Mount Sinabung ash to CBR (California Bearing Ratio) value, to determine the effect of the curing time of one day and fourteen days mixture on the CBR value, and to find the mixed content with effective curing time to produce the largest CBR value. Based on this study, the soil type CL (Clay - Low Plasticity) was obtained, based on the classification of USCS (Unified Soil Classification System) and categorized as A-6 (6) based on the classification of AASHTO (American Association of State Highway and Transportation officials) with the most effective mixed stabilizer material which was the variation of 10% Mount Sinabung ash with fourteen days of curing time. The CBR value resulted from the mixture of 10% Sinabung ash that was cured within fourteen days was 8.95%. By the increase of the content of the Sinabung ash, the CBR value always improved to the level of 10%, Sinabung ash then decreased and became constant at the mixture of higher volcanic ash mixture but remained above the CBR value of the original soil.

RARE EARTH ELEMENTS IN FLY ASHES AS POTENTIAL INDICATORS OF ANTHROPOGENIC SOIL CONTAMINATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V.

2003-08-01

Studies of rare earth element (REE) content of disposed fly ashes and their potential mobility were neglected for decades because these elements were believed to be environmentally benign. A number of recent studies have now shown that REE may pose a long-term risk to the biosphere. Therefore, there is a critical need to study the REE concentrations in fly ash and their potential mobilization and dispersal upon disposal in the environment. We analyzed the REE content of bulk, size fractionated, and density separated fractions of three fly ash samples derived from combustion of sub bituminous coals from the western Unitedmore » States and found that the concentrations of these elements in bulk ashes were within the range typical of fly ashes derived from coals from the North American continent. The concentrations of light rare earth elements (LREE) such as La, Ce, and Nd, however, tended towards the higher end of the concentration range whereas, the concentrations of middle rare earth elements (MREE) (Sm and Eu) and heavy rare earth elements (HREE) (Lu) were closer to the lower end of the observed range for North American fly ashes. The concentrations of REE did not show any significant enrichment with decreasing particle size, this is typical of nonvolatile lithophilic element behavior during the combustion process. The lithophilic nature of REE was also confirmed by their concentrations in heavy density fractions of these fly ashes being on average about two times more enriched than the concentrations in the light density fractions. Shale normalized average of REE concentrations of fly ashes and coals revealed significant positive anomalies for Eu and Dy. Because of these distinctive positive anomalies of Eu and Dy, we believe that fly ash contamination of soils can be fingerprinted and distinguished from other sources of anthropogenic REE inputs in to the environment.« less

Testing exposure of a jet engine to a dilute volcanic-ash cloud

NASA Astrophysics Data System (ADS)

Guffanti, M.; Mastin, L. G.; Schneider, D. J.; Holliday, C. R.; Murray, J. J.

2013-12-01

An experiment to test the effects of volcanic-ash ingestion by a jet engine is being planned for 2014 by a consortium of U.S. Government agencies and engine manufacturers, under the auspices of NASA's Vehicle Integrated Propulsion Research Program. The experiment, using a 757-type engine, will be an on-ground, on-wing test carried out at Edwards Air Force Base, California. The experiment will involve the use of advanced jet-engine sensor technology for detecting and diagnosing engine health. A primary test objective is to determine the effect on the engine of many hours of exposure to ash concentrations (1 and 10 mg/cu m) representative of ash clouds many 100's to >1000 km from a volcanic source, an aviation environment of great interest since the 2010 Eyjafjallajökull, Iceland, eruption. A natural volcanic ash will be used; candidate sources are being evaluated. Data from previous ash/aircraft encounters, as well as published airborne measurements of the Eyjafjallajökull ash cloud, suggest the ash used should be composed primarily of glassy particles of andesitic to rhyolitic composition (SiO2 of 57-77%), with some mineral crystals, and a few tens of microns in size. Collected ash will be commercially processed less than 63 microns in size with the expectation that the ash particles will be further pulverized to smaller sizes in the engine during the test. For a nominally planned 80 hour test at multiple ash-concentration levels, the test will require roughly 500 kg of processed (appropriately sized) ash to be introduced into the engine core. Although volcanic ash clouds commonly contain volcanic gases such as sulfur dioxide, testing will not include volcanic gas or aerosol interactions as these present complex processes beyond the scope of the planned experiment. The viscous behavior of ash particles in the engine is a key issue in the experiment. The small glassy ash particles are expected to soften in the engine's hot combustion chamber, then stick to cooler parts of the turbine. Composition (primarily silica content) and dissolved water content, both of which affect the softening temperature of silicate melts, will be taken into account when evaluating candidate ash sources, although the practicalities of collecting, shipping, and processing a substantial amount of ash are a major decision factor in source selection.

[Husk of Venezuelan cocoa as raw material of infusions].

PubMed

Sangronis, Elba; José Soto, María; Valero, Yolmar; Buscema, Ignacio

2014-06-01

In the cocoa bean industry, some by-products go underutilized. Some of these components could provide other innovative products, and such is the case with the husk of the cocoa bean. Previous studies have attributed the husk with a high antioxidant capacity, which added to its relative low cost, makes it an attractive ingredient for the production of infusions. However, prior to promoting it as such, its quality needs to be guaranteed. This study evaluated the chemical composition of the husk of cocoa, its microbiologic quality and other parameters in order to be considered raw material in the preparation of infusions. The cocoa was cultivated in two different states in Venezuela. Moisture, protein, fat, ash, carbohydrates, microbiologic quality and ochratoxin A as well antioxidant properties, content of foreign matter, insoluble ash in HCL and aqueous extract were evaluated in the husk of cocoa seeds. Applied methods were in compliance with national and international norms. Significant differences were determined between the samples through the ANOVA application. A low level in moisture content, but high in ash, along with a microbiologic quality that met the norm, and an absence of ochratoxin A were observed in the totality of the analyzed samples. Low levels of foreign matter, the high value of its aqueous extract and high phenolic compounds content with antioxidant activity allow for the recommendation of the husk of cocoa as raw material for the preparation of infusions.

Sources of biomass feedstock variability and the potential impact on biofuels production

DOE PAGES

Williams, C. Luke; Westover, Tyler L.; Emerson, Rachel M.; ...

2015-11-23

In this study, terrestrial lignocellulosic biomass has the potential to be a carbon neutral and domestic source of fuels and chemicals. However, the innate variability of biomass resources, such as herbaceous and woody materials, and the inconsistency within a single resource due to disparate growth and harvesting conditions, presents challenges for downstream processes which often require materials that are physically and chemically consistent. Intrinsic biomass characteristics, including moisture content, carbohydrate and ash compositions, bulk density, and particle size/shape distributions are highly variable and can impact the economics of transforming biomass into value-added products. For instance, ash content increases by anmore » order of magnitude between woody and herbaceous feedstocks (from ~0.5 to 5 %, respectively) while lignin content drops by a factor of two (from ~30 to 15 %, respectively). This increase in ash and reduction in lignin leads to biofuel conversion consequences, such as reduced pyrolysis oil yields for herbaceous products as compared to woody material. In this review, the sources of variability for key biomass characteristics are presented for multiple types of biomass. Additionally, this review investigates the major impacts of the variability in biomass composition on four conversion processes: fermentation, hydrothermal liquefaction, pyrolysis, and direct combustion. Finally, future research processes aimed at reducing the detrimental impacts of biomass variability on conversion to fuels and chemicals are proposed.« less

The Application of FT-IR Spectroscopy for Quality Control of Flours Obtained from Polish Producers

PubMed Central

Ceglińska, Alicja; Reder, Magdalena; Ciemniewska-Żytkiewicz, Hanna

2017-01-01

Samples of wheat, spelt, rye, and triticale flours produced by different Polish mills were studied by both classic chemical methods and FT-IR MIR spectroscopy. An attempt was made to statistically correlate FT-IR spectral data with reference data with regard to content of various components, for example, proteins, fats, ash, and fatty acids as well as properties such as moisture, falling number, and energetic value. This correlation resulted in calibrated and validated statistical models for versatile evaluation of unknown flour samples. The calibration data set was used to construct calibration models with use of the CSR and the PLS with the leave one-out, cross-validation techniques. The calibrated models were validated with a validation data set. The results obtained confirmed that application of statistical models based on MIR spectral data is a robust, accurate, precise, rapid, inexpensive, and convenient methodology for determination of flour characteristics, as well as for detection of content of selected flour ingredients. The obtained models' characteristics were as follows: R2 = 0.97, PRESS = 2.14; R2 = 0.96, PRESS = 0.69; R2 = 0.95, PRESS = 1.27; R2 = 0.94, PRESS = 0.76, for content of proteins, lipids, ash, and moisture level, respectively. Best results of CSR models were obtained for protein, ash, and crude fat (R2 = 0.86; 0.82; and 0.78, resp.). PMID:28243483

Effect of cooking on the proximate composition of seven accessions of Colocasia esculenta (L.) Schott tubers growing in South Africa.

PubMed

Lewu, Muinat N; Adebola, Patrick O; Afolayan, Anthony J

2009-01-01

Colocasia esculenta (L.) Schott (cocoyam) is cultivated mainly for its edible tubers. The effect of cooking the tubers on the proximate composition of seven accessions (UFCe1-UFCe7) of the crop growing in South Africa was investigated. When compared with the uncooked, the ash and crude fibre contents of the accessions significantly decreased after cooking. The moisture content, crude protein, crude lipid, carbohydrate and caloric contents increased with cooking in all the accessions, except UFCe1 and UFCe5 where the crude lipid content reduced. The results indicate that cooking enhanced the carbohydrate, energy and protein contents of the tubers. They further showed that the tubers could be used for allergic infants, old people and invalids since the fibre contents were still appreciably high despite the slight reduction after cooking the tubers.

Applicability of the mixture of bituminous coal and anthracite to conventional pulverized coal firing boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takano, Shin-Ichi; Kiga, Takashi; Miyamae, Shigehiro

1994-12-31

In some future, it is expected for Japanese power stations to be hard to get a high-grade coal like a bituminous coal. We conducted therefore pilot scale tests of pulverized blends of bituminous coal and anthracite using a 1.2MWt tunnel furnace in order to evaluate the applicability of the blends of bituminous coal and anthracite to conventional pulverized coal firing boilers. One kind of bituminous coal and two kinds of anthracite, one was of low ash content and another was of high ash content, were prepared for the test. Previously to pilot scale tests, coal properties and ash properties ofmore » the blends of bituminous coal and anthracite were analyzed to estimate the characteristics of combustion, ash deposition, and so on. In the test, we investigated the combustion efficiency, NOx emission, characteristics of ignition stability and grindability changing the blend rate of anthracite. Results of our study indicated that the critical restrictions on the blending rate of anthracite were unburnt carbon in fly ash and NOx emission as for coals tested. The acceptable limitation on blending rate of anthracite was 10 and 20%, respectively for two kinds of conventional pulverized coal fired boiler. Concerning to the grindability, it became worse with increasing the blending rate of anthracite from grindability test using a roller mill, while it became better estimating from HGI.« less

Osteoporotic-like effects of cadmium on bone mineral density and content in aged ovariectomized beagles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sacco-Gibson, N.; Abrams, J.; Chaudhry, S.

1992-12-31

Our purpose was to evaluate the effects of ovariectomy in conjunction with cadmium (Cd) exposure on bone. Aged female beagles with {sup 45}Ca-labeled skeletons ovariectomized and exposed to Cd. Successive vertebral scans by dual photon absorptiometry monitored changes in bone mineral density (BMD) in each dog with time. Results showed that ovariectomy or Cd exposure alone caused significant decreases in BMD; ovariectomy with Cd exposure caused the greatest decrease. Ovariectomy alone did not decrease BMD in the distal end or mid-shaft of the tibia while BMD of the distal tibia decreased significantly due to Cd exposure alone. Combination treatment resultedmore » in significant decreases in BMD of both tibial regions. At necropsy, tibiae, humeri, lumbar vertebrae and ribs were obtained for biochemical analysis. No group-to-group differences in bone weights (wet, dry, ash), in ash/dry ratios, or in long bone and vertebral Ca/dry or Ca/ash ratios were observed. Significantly higher total {sup 45}Ca content and {sup 45}Ca/dry and {sup 45}Ca/ash ratios were observed in long bones and vertebrae of OV- and OV+ groups. In contrast, intact ribs showed significantly decreased Ca/dry and Ca/ash ratios compared to the SO-group. Quartered ribs demonstrated regional responses to specific treatment; decreases in total Ca content were greatest in the mid-rib region ({minus}36 to {minus}46%). Results suggest that in the aged female beagle, bone mineral loss associated with estrogen depletion is not only related to bone type (trabecular versus cortical) but also to bone Ca pools. Our results also suggest that a regional heterogeneity of bone plays a role in responsiveness to ovariectomy and Cd exposure. These aspects suggest that Cd is an exogenous factor affecting bone mineral loss independently of estrogen depletion. However, estrogen depletion primes bone for responsiveness to Cd-induced bone mineral loss.« less

Environmental, physical and structural characterisation of geopolymer matrixes synthesised from coal (co-)combustion fly ashes.

PubMed

Alvarez-Ayuso, E; Querol, X; Plana, F; Alastuey, A; Moreno, N; Izquierdo, M; Font, O; Moreno, T; Diez, S; Vázquez, E; Barra, M

2008-06-15

The synthesis of geopolymer matrixes from coal (co-)combustion fly ashes as the sole source of silica and alumina has been studied in order to assess both their capacity to immobilise the potentially toxic elements contained in these coal (co-)combustion by-products and their suitability to be used as cement replacements. The geopolymerisation process has been performed using (5, 8 and 12 M) NaOH solutions as activation media and different curing time (6-48 h) and temperature (40-80 degrees C) conditions. Synthesised geopolymers have been characterised with regard to their leaching behaviour, following the DIN 38414-S4 [DIN 38414-S4, Determination of leachability by water (S4), group S: sludge and sediments. German standard methods for the examination of water, waste water and sludge. Institut für Normung, Berlin, 1984] and NEN 7375 [NEN 7375, Leaching characteristics of moulded or monolithic building and waste materials. Determination of leaching of inorganic components with the diffusion test. Netherlands Normalisation Institute, Delft, 2004] procedures, and to their structural stability by means of compressive strength measurements. In addition, geopolymer mineralogy, morphology and structure have been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR), respectively. It was found that synthesised geopolymer matrixes were only effective in the chemical immobilisation of a number of elements of environmental concern contained in fly ashes, reducing (especially for Ba), or maintaining their leachable contents after the geopolymerisation process, but not for those elements present as oxyanions. Physical entrapment does not seem either to contribute in an important way, in general, to the immobilisation of oxyanions. The structural stability of synthesised geopolymers was mainly dependent on the glass content of fly ashes, attaining at the optimal activation conditions (12 M NaOH, 48 h, 80 degrees C) compressive strength values about 60 MPa when the fly ash glass content was higher than 90%.

Development of clean coal and clean soil technologies using advanced agglomeration technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ignasiak, B.; Pawlak, W.; Szymocha, K.

1990-04-01

The specific objectives of the bituminous coal program were to explore and evaluate the application of advanced agglomeration technology for: (1)desulphurization of bituminous coals to sulphur content acceptable within the current EPA SO{sub 2} emission guidelines; (2) deashing of bituminous coals to ash content of less than 10 percent; and (3)increasing the calorific value of bituminous coals to above 13,000 Btu/lb. (VC)

Wood and bark moisture contents of small-diameter hardwoods growing on southern pine sites

Treesearch

F.G. Manwiller

1975-01-01

Ten 6-inch trees from throughout the South were sampled from each of 22 species, of which 11 were oaks. Ranking of species remained constant regardless of whether moisture contents were determined for the entire tree, the stem with bark, branches with bark, or stem- and branchwood without bark. For ashes and hickory, the range among these various components was 46 to...

Wood and bark moisture contents of small-diameter hardwoods growing on southern pine sites

Treesearch

Floyd G. Manwiller

1975-01-01

Ten 6-inch trees from throughout the south were sampled from each of 22 species, of which 11 were oaks. Ranking of species remained constant regardless of whether moisture contents were determined for the entire tree, the stem with bark, branches with bark, or stem- and branchwood without bark. For ashes and hickory, the range among these various components was 46 to...

Hydrogeochemical processes of wastewater leakage purification from a thermal power plant.

PubMed

Pavlov, Sergey Kh; Chudnenko, Konstantin V

2015-01-01

The hydrogeochemical conditions of a large flatland-type ash dump (Eastern Siberia, Russia) were studied. High-alkalinity sulphate water with high calcium content was found to infiltrate into the aquifer from the ash dump. The water was transformed into neutral bicarbonate solutions. Simulation of physicochemical interactions of the clarified water with ash, sandstone, and soil demonstrated that the composition of the resulting simulated solutions is similar to composition of the transformed clarified water leaking into the aquifer, and moving at various distances from their place of infiltration towards the discharge area.

Evaluation of the proximate quality of the combination of Tuna (Thunnus albacares) and white oyster mushroom (Pleurotus ostreatus) nuggets

NASA Astrophysics Data System (ADS)

Yufidasari, H. S.; Prihanto, A. A.; Nurdiani, R.; Jaziri, A. A.

2018-04-01

Nugget is a processed meat product which has great market demand but need variations to increase its nutritional content. Tuna is rich in omega-3 protein, vitamins, and minerals. White oyster mushrooms have high nutritional content which are about 23-33% protein, 36-68 % carbohydrates and 12-22 % amino acids. The purpose of this research is to evaluate the chemical quality of Tuna nugget (Thunnus albacores) with combination of white oyster mushroom (Pleurotus ostreatus). Complete Randomized Design (RAL) with parameters of Tuna and white oyster mushroom formulation, TJ1 (70 % Tuna: 30 % white oyster mushroom), TJ2 (50 % Tuna: 50 % white oyster mushroom), TJ3 (30 % Tuna: 70 % white oyster mushroom), and Control or K Treatment (100 % Tuna) is used. Results of Tuna nuggets with white oyster mushroom combination showed the highest value of water content in TJ3 50.14 %, protein K 19.6 %, fat TJ3 22.98 %, ash K 3.99 % and 2.47 % crude fiber. From these results, there is a need for further research on fat, ash and coarse fiber content that is used in the manufacture of fish nuggets combined with oyster mushrooms because it failed to meet Indonesian National Standard (SNI).

Physicochemical properties of chitooligosaccharide prepared by using chitosanase from Stenotrophomonas maltophilia KPU 2123

NASA Astrophysics Data System (ADS)

Fawzya, Y. N.; Rahmawati, A.; Patantis, G.

2018-03-01

Study on the physicochemical properties of chitooligosaccharide (COS) prepared by hydrolysis of chitosan using chitosanase from Stenotrophomonas maltophilia KPU 2123 has been carried out. Hydrolysis process was conducted by reacting the soluble chitosan with 8 U·g-1 chitosan of chitosanase for 0; 8; 16 and 24 h incubation and stopped by addition of 0.25 M NaOH until reached pH 7. The COS was obtained as supernatant after being centrifugation. The liquid COS were then freeze-dried and analyzed their physicochemical properties, which comprised yield, viscosity, moisture and ash content, the degree of deacetylation (DD), as well as lead (Pb), arsenic (As) content and analyses of COS by Thin Layer Chromatography (TLC). The optimum hydrolysis time was found to be 16 h with the COS viscosity was 8.50 ± 0.87 cPs. The high COS yield was related to high ash content, i.e. 251.70 ± 77.97 % and 50.45 ± 3.19 % (db), respectively. There was lead (Pb) and arsenic (As) metals detected, i.e. 4.4 ppm and 0.1 ppm, respectively. However, they still met the requirement of Pb and As content in a commercial COS referred. Based on the COS properties, desalination process should be applied in the preparation of COS by enzymatic method.

Fuel Characterization of Newly Discovered Nigerian Coals

NASA Astrophysics Data System (ADS)

Bevan Nyakuma, Bemgba; Oladokun, Olagoke; Jauro, Aliyu; Damian Nyakuma, Denen

2017-07-01

This study seeks to characterize and highlight the fuel properties, rank, and classification of coals from Ihioma (IHM) and Ogboligbo (OGB) in Imo and Kogi states of Nigeria, respectively. The fuel properties were examined based on ultimate, proximate, and bomb calorific analyses. The results indicated that IHM coal contains comparatively higher C and H but lower O, N, and S content than OGB. In addition, the nitrogen (N) and sulphur (S) content for both coal samples were above 0.7 wt.% and 1.5 wt.%, respectively, which indicates high potential for pollutant emissions. Furthermore, the coal proximate properties were below 5 wt.% for Moisture; Volatiles (70 wt.%); Fixed Carbon (45 wt.%) and Ash (2.5 wt.%) on average. IHM coal has an HHV of 19.40 MJ/kg whereas OGB is 15.55 MJ/kg. This is due to the low carbon (C), hydrogen (H) and high oxygen (O) content in OGB whereas IHM contains higher VM and HHV. Furthermore, OGB presents better handling, storage, and transport potential. Furthermore, OGB has a higher fuel ratio and value index due to lower moisture, ash content, and volatiles. Based on the ASTM D388 standard, the coals were classified as Lignite (Brown) Low-Rank Coals (LRCs) with potential for energy recovery.

Proximate composition and nutritional quality of deep sea growth sea cucumbers (Stichopus japonicus) from different origins.

PubMed

Gao, Yue; Li, Zhibo; Qi, Yanxia; Guo, Zhenyu; Lin, Yantong; Li, Wei; Hu, Yucai; Zhao, Qiancheng

2016-05-01

Deep sea growth sea cucumber (Stichopus japonicus) (DSG-SC) is considered a most nutritious and luxurious seafood in Asia. This study compared the proximate composition and nutritional quality of collagen, polysaccharides, amino acids (AAs) and fatty acids (FAs) in DSG-SCs from different origins. The contents of protein, ash, carbohydrate, fat, collagen, saturated fatty acids (SFAs), monounsaturated fatty acids (MUFAs), polyunsaturated fatty acids (PUFAs), total amino acids (TAAs), essential amino acids (EAAs), fucose and uronic acid differed among the origins. DSG-SC of Dalian origin had lower contents of ash, fat, uronic acid, TAAs and EAAs but higher contents of protein, collagen, PUFAs, eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA) and fucose compared with the other origins. DSG-SCs had a higher proportion of PUFAs and were richer in polysaccharides than other seafood. Glutamate and glycine were the dominant AAs, while leucine and threonine were the most abundant EAAs. DSG-SCs are a good source of collagen, polysaccharides (especially fucose), EAAs (especially leucine and threonine) and PUFAs (especially EPA and DHA). Dalian seems to be a promising origin to produce high-value sea cucumber with high PUFA, fucose, collagen and protein contents. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Proximate composition and mineral contents in the body wall of two species of sea cucumber from Oman Sea.

PubMed

Barzkar, Noora; Attaran Fariman, Gilan; Taheri, Ali

2017-08-01

The proximate composition and mineral contents of Stichopus horrens and Holothuria arenicola from Chabahar Bay were analyzed and investigated. During the present study, we aimed to demonstrate the nutritive value. The approximate percent composition of moisture, protein, fat, and ash were 92.8, 3.47, 0.4, and 3.33% in S. horrens and 93, 4.4, 0.6, and 2% in H. arenicola, respectively. Atomic absorption spectrophotometry of the ashes indicated the body wall of two species of sea cucumbers contained higher amounts of both macro minerals (92.5 mg/100 g Mg in S. horrens and 115 mg/100 g Mg in H. arenicola; 106.25 mg/100 g Ca in S. horrens and 83.25 mg/100 g Ca in H. arenicola) and trace elements (521.781 mg/100 g Fe in S. horrens; 60.354 mg/100 g Fe in H. arenicola, and 0.096 mg/100 g Zn in S. horrens; 0.04 mg/100 g Zn in H. arenicola). For both species, there were high content of protein and essential mineral. Also, they have low content of fat in the body wall of two species in the experiment.

A study of the effect of selected material properties on the ablation performance of artificial graphite

NASA Technical Reports Server (NTRS)

Maahs, H. G.

1972-01-01

Eighteen material properties were measured on 45 different, commercially available, artificial graphites. Ablation performance of these same graphites were also measured in a Mach 2 airstream at a stagnation pressure of 5.6 atm. Correlations were developed, where possible, between pairs of the material properties. Multiple regression equations were then formulated relating ablation performance to the various material properties, thus identifying those material properties having the strongest effect on ablation performance. These regression equations reveal that ablation performance in the present test environment depends primarily on maximum grain size, density, ash content, thermal conductivity, and mean pore radius. For optimization of ablation performance, grain size should be small, ash content low, density and thermal conductivity high, and mean pore radius large.

In vitro digestibility of banana starch cookies.

PubMed

Bello-Pérez, Luis A; Sáyago-Ayerdi, Sonia G; Méndez-Montealvo, Guadalupe; Tovar, Juscelino

2004-01-01

Banana starch was isolated and used for preparation of two types of cookies. Chemical composition and digestibility tests were carried out on banana starch and the food products, and these results were compared with corn starch. Ash, protein, and fat levels in banana starch were higher than in corn starch. The high ash amount in banana starch could be due to the potassium content present in this fruit. Proximal analysis was similar between products prepared with banana starch and those based on corn starch. The available starch content of the banana starch preparation was 60% (dmb). The cookies had lower available starch than the starches while banana starch had lower susceptibility to the in vitro alpha-amylolysis reaction. Banana starch and its products had higher resistant starch levels than those made with corn starch.

Genetic determinism of bone and mineral metabolism in meat-type chickens: A QTL mapping study.

PubMed

Mignon-Grasteau, Sandrine; Chantry-Darmon, Céline; Boscher, Marie-Yvonne; Sellier, Nadine; Chabault-Dhuit, Marie; Le Bihan-Duval, Elisabeth; Narcy, Agnès

2016-12-01

Skeletal integrity in meat-type chickens is affected by many factors including rapid growth rate, nutrition and genetics. To investigate the genetic basis of bone and mineral metabolism, a QTL detection study was conducted in an intercross between two lines of meat-type chickens divergently selected for their high (D +) or low (D -) digestive efficiency. Tibia size (length, diameter, volume) and ash content were determined at 3 weeks of age as well as phosphorus (P) retention and plasma concentration. Heritability of these traits and their genetic correlations with digestive efficiency were estimated. A QTL mapping study was performed using 3379 SNP markers. Tibia size, weight, ash content and breaking strength were highly heritable (0.42 to 0.61). Relative tibia diameter and volume as well as P retention were strongly and positively genetically correlated with digestive efficiency (0.57 to 0.80). A total of 35 QTL were identified (9 for tibia weight, 13 for tibia size, 5 for bone strength, 5 for bone mineralization, 2 for plasma P concentration and 1 for P retention). Six QTL were genome-wide significant, and 3 QTL for tibia relative volume, weight and ash weight on chromosome 6 were fixed, the positive allele coming from the D-line. For two QTL for ash content on chromosome 18 and relative tibia length on chromosome 26, the confidence intervals were small enough to identify potential candidate genes. These findings support the evidence of multiple genetic loci controlling bone and mineral metabolism. The identification of candidate genes may provide new perspectives in the understanding of bone regulation, even beyond avian species.

Chemical and biological characterization of organic matter during composting of municipal solid waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chefetz, B.; Yona Chen; Hadar, Y.

Composting of municipal solid waste (MSW) was studied in an attempt to elaborate transformations of organic matter (OM) during the process and define parameters for the degree of maturity of the product. Composting was performed in 1-m{sup 3} plastic boxes and the following parameters were measured in 13 samples during 132 d of composting: temperature, C/N ratio, ash content, humic substance contents, and fractions (humic acid, fulvic acid, and nonbumic fraction-HA, FA and NHF, respectively). Spectroscopic methods (CPMAS {sup 13}C-NMR, DRIFT) were used to study the chemical composition of the OM. A bioassay based on growth of cucumber (Cucumis satifusmore » L. cv. Dlila) plants was correlated to other parameters. The C/N ratio and ash content showed a typical high rate of change during the first 60 d and reached a plateau thereafter. The HA content increased to a maximum at 112 d, corresponding to the highest plant dry weight and highest 1650/1560 (cm{sup {minus}1}/cm{sup {minus}1}) peak ratios calculated from DRIFT spectra. {sup 13}C-NMR and DRIFT spectra of samples taken from the composting MSW during the process showed that the residual OM contained an increasing level of aromatic structures. Plant-growth bioassay, HA content, and the DRIFT spectra indicated that MSW compost described in this study, stabilized and achieved maturity after about 110 d. 31 refs., 8 figs., 2 tabs.« less

Spatial variation of peat soil properties in the oil-producing region of northeastern Sakhalin

NASA Astrophysics Data System (ADS)

Lipatov, D. N.; Shcheglov, A. I.; Manakhov, D. V.; Zavgorodnyaya, Yu. A.; Rozanova, M. S.; Brekhov, P. T.

2017-07-01

Morphology and properties of medium-deep oligotrophic peat, oligotrophic peat gley, pyrogenic oligotrophic peat gley, and peat gley soils on subshrub-cotton grass-sphagnum bogs and in swampy larch forests of northeastern Sakhalin have been studied. Variation in the thickness and reserves of litters in the studied bog and forest biogeocenoses has been analyzed. The profile distribution and spatial variability of moisture, density, ash, and pHKCl in separate groups of peat soils have been described. The content and spatial variability of petroleum hydrocarbons have been considered in relation to the accumulation of natural bitumoids by peat soils and the technogenic pressing in the oil-producing region. Variation of each parameter at different distances (10, 50, and 1000 m) has been estimated using a hierarchical sampling scheme. The spatial conjugation of soil parameters has been studied by factor analysis using the principal components method and Spearman correlation coefficients. Regression equations have been proposed to describe relationships of ash content with soil density and content of petroleum hydrocarbons in peat horizons.

Impact of torrefaction and low-temperature carbonization on the properties of biomass wastes from Arundo donax L. and Phoenix canariensis.

PubMed

Correia, Ricardo; Gonçalves, Margarida; Nobre, Catarina; Mendes, Benilde

2017-01-01

The impact of torrefaction and low-temperature carbonization on the properties of biomass wastes from Arundo donax L. and Phoenix canariensis was studied. Thermal treatments were performed at temperatures from 200°C to 350°C during 15 to 90min and temperature was the parameter that more influenced mass and energy yields as well as biochar composition. Torrefaction reduced moisture, volatile matter, O/C and H/C ratios of the biomass, while increasing heating value, ash content and fixed carbon. For torrefaction at 250°C or higher temperatures grindability of the biochars was significantly improved. The low volatile matter contents and high ash contents of these biochars restricts their use as solid fuels but they can be valorized otherwise. Raw biomasses and the biochars torrefied at 200°C could remove methylene blue from an aqueous solution, in fast adsorption test with a contact time of only 3s, with efficiencies higher than 50%. Copyright © 2016 Elsevier Ltd. All rights reserved.

Simulated Impacts of Emerald Ash Borer on Throughfall and Stemflow Inputs of Water and Nitrogen in Black Ash Wetlands in Northern Michigan

NASA Astrophysics Data System (ADS)

Pypker, T. G.; Davis, J.; Van Grinsven, M. J.; Bolton, N. W.; Shannon, J.; Kolka, R. K.; Nelson, J.; Wagenbrenner, J. W.

2014-12-01

Emerald ash borer (Agrilus planipennis Fairmaire (EAB)) is an invasive insect that effectively kills ash trees (genus: Fraxinus) greater than 2.5 cm in diameter, resulting in near-complete stand mortality within 3-4 years. Black ash wetlands occupy approximately 270,000 ha in Michigan, and have 40 to 90% of the basal area occupied by black ash (F. nigra Marshall); hence the loss of black ash may result in dramatic changes in the canopy hydrology and nutrient deposition. We assessed the impact of a simulated EAB invasion on throughfall and stemflow quantity and nitrogen (N) content in 9 uninfected black ash wetlands located in the Upper Peninsula of Michigan. Within the 9 stands, 3 stands were left untreated ('Control'), 3 stands had all the black ash trees manually girdled ('Girdled') and 3 had all the black ash trees felled by chainsaw ('Clearcut'). We measured the quantity and inorganic-N content of throughfall using an array of randomly placed collectors (n = 16 per site). Stemflow was monitored at 2 sites (n = 12 trees) on the 3 most common tree species (black ash, yellow birch (Betula alleghaniensis Britt.) and red maple (Acer rubra L.)). Preliminary results indicate that relative to the Control, average monthly throughfall was 25% and 1% greater in the Clearcut and Girdled sites, respectively. While the loss of the ash trees resulted in greater throughfall inputs in the Clearcut sites, water table heights did not significantly change as a result of the treatments. Stemflow from live black ash trees was lower than from the yellow birch and red maple trees. As a result, we predict stemflow will increase over time as species with smoother bark and less upright branching begin replacing the black ash. Hence, the change in tree species may result in a greater concentration of inorganic-N inputs to the base of the trees, thereby altering the distribution of inorganic-N inputs into the wetland. Our preliminary results show no significant change in the total inorganic-N deposition via throughfall. Despite the severity of the disturbance that resulted from the simulated EAB infestation, preliminary results suggest that that these wetlands may show some short-term resiliency to the impacts of ash mortality, resulting in relatively unchanged hydrologic and nutrient deposition regimes.

APC fly ashes stabilized with Portland cement for further development of road sub-base aggregates

NASA Astrophysics Data System (ADS)

Formosa, J.; Giro-Paloma, J.; Maldonado-Alameda, A.; Huete-Hernández, S.; Chimenos, J. M.

2017-10-01

Although waste-to-energy plants allow reducing the mass and volume of municipal solid waste (MSW) incinerated, an average around 30 % of the total content remains as bottom ash (BA) and air pollution control (APC) ashes at the end of combustion process. While weathered bottom ash (WBA) is considered a non-hazardous residue that can be revalorized as a secondary aggregate, APC fly ashes generated during the flue gas treatment are classified as hazardous waste and are handled in landfill disposal after stabilization, usually with Portland cement (OPC). However, taking into account the amount of APC residues produced and the disposing cost in landfill, their revalorization is an important issue that could be effectively addressed. As MSW can be incinerated producing bottom ashes (BA) or air pollutant control (APC) residues, the development of a mortar formulated with APC fly ash as secondary building material is a significant risk to the environment for their content of heavy metals. In this way, Design of Experiment (DoE) was used for the improvement of granular material (GM) formulation composed by APC and OPC for further uses as road sub-base aggregate. DoE analysis was successful in the modelling and optimization the formulation as function of the mechanical properties and APC amount. Consequently, an optimal mortar formulation (OMF) of around 50 wt.% APC and 50 wt.% OPC was considered. The OMF leachates and abrasion resistance have been analyzed. These results have demonstrated the viability of OMF as non-hazardous material feasible to be used as secondary aggregate. Moreover, it would be possible to consider the environmental assessment of a GM composed by ≈20 wt.% of OMF and ≈80 wt.% of WBA in order to improve mechanical properties and heavy metals stabilization.

Novel incineration technology integrated with drying, pyrolysis, gasification, and combustion of MSW and ashes vitrification.

PubMed

Liu, Yangsheng; Liu, Yushan

2005-05-15

The conventional mass burn systems for municipal solid waste (MSW) emit large amount of acidic gases and dioxins as well as heavy metals due to the large excess air ratio. Additionally, the final process residues, bottom ash with potential leachability of heavy metals and fly ash with high level of heavy metals and dioxins, also constitute a major environmental problem. To deal with these issues more effectively, a novel MSW incineration technology was developed in this study. MSW drying, pyrolysis, gasification, incineration, and ash vitrification were achieved as a spectrum of combustion by the same equipment (primary chamber) in one step. In practice, the primary chamber of this technology actually acted as both gasifier for organic matter and vitrifying reactor for ashes, and the combustion process was mainly completed in the secondary chamber. Experiments were carried outto examine its characteristics in an industrial MSW incineration plant, located in Taiyuan, with a capability of 100 tons per day (TPD). Results showed that (1) the pyrolysis, gasification, and vitrification processes in the primary chamber presented good behaviors resulting in effluent gases with high contents of combustibles (e.g., CO and CH4) and bottom ash with a low loss-on-ignition (L.o.l), low leachability of heavy metals, and low toxicity of cyanide and fluoride. The vitrified bottom ash was benign to its environment and required no further processing for its potential applications. (2) Low stack emissions of dioxins (0.076 ng of TEQ m(-3)), heavy metals (ranging from 0.013 to 0.033 mg m(-3)), and other air pollutants were achieved. This new technology could effectively dispose Chinese MSW with a low calorific value and high water content; additionally, it also had a low capital and operating costs compared with the imported systems.

Inorganic geochemistry of domed peat in Indonesia and its implication for the origin of mineral matter in coal

USGS Publications Warehouse

Neuzil, Sandra G.; Supardi,; Cecil, C. Blaine; Kane, Jean S.; Soedjono, Kadar

1993-01-01

The inorganic geochemistry of three domed ombrogenous peat deposits in Riau and West Kalimantan provinces, Indonesia, was investigated as a possible modern analogue for certain types of low-ash, low-sulfur coal. Mineral matter entering the deposits is apparently limited to small amounts from the allogenic sources of dryfall, rainfall, and diffusion from substrate pore water. In the low-ash peat in the interior of the deposits, a large portion of the mineral matter is authigenic and has been mobilized and stabilized by hydrological, chemical, and biological processes and conditions.Ash yield and sulfur content are low through most of the peat deposits and average 1.1% and 0.14%, respectively, on a moisture-free basis. Ash and sulfur contents only exceed 5% and 0.3%, respectively, near the base of the deposits, with maximum concentrations of 19.9% ash and 0.56% sulfur. Peat water in all three deposits has a low pH, about 4 units, and low dissolved cation concentration, averaging 14 ppm. Near the base, in the geographic interior of each peat deposit, pH is about two units higher and dissolved cation concentration averages 110 ppm. Relative concentrations of the inorganic constituents vary, resulting in chemical facies in the peat. In general, Si, Al, and Fe are the abundant inorganic constituents, although Mg, Ca, and Na dominate in the middle horizon in the geographic interior of coastal peat deposits.The composition of the three deposits reported in this paper indicates that domed ombrogenous peat deposits will result in low ash and sulfur coal, probably less than 10% ash and 1% sulfur, even if marine rocks are laterally and vertically adjacent to the coal.

Modernization of the International Volcanic Ash Website - a global resource for ashfall preparedness and impact guidance.

NASA Astrophysics Data System (ADS)

Wallace, K.; Leonard, G.; Stewart, C.; Wilson, T. M.; Randall, M.; Stovall, W. K.

2015-12-01

The internationally collaborative volcanic ash website (http://volcanoes.usgs.gov/ash/) has been an important global information resource for ashfall preparedness and impact guidance since 2004. Recent volcanic ashfalls with significant local, regional, and global impacts highlighted the need to improve the website to make it more accessible and pertinent to users worldwide. Recently, the Volcanic Ash Impacts Working Group (Cities and Volcanoes Commission of IAVCEI) redesigned and modernized the website. Improvements include 1) a database-driven back end, 2) reorganized menu navigation, 3) language translation, 4) increased downloadable content, 5) addition of ash-impact case studies, 7) expanded and updated references , 8) an image database, and 9) inclusion of cooperating organization's logos. The database-driven platform makes the website more dynamic and efficient to operate and update. New menus provide information about specific impact topics (buildings, transportation, power, health, agriculture, water and waste water, equipment and communications, clean up) and updated content has been added throughout all topics. A new "for scientists" menu includes information on ash collection and analysis. Website translation using Google translate will significantly increase user base. Printable resources (e.g. checklists, pamphlets, posters) provide information to people without Internet access. Ash impact studies are used to improve mitigation measures during future eruptions, and links to case studies will assist communities' preparation and response plans. The Case Studies menu is intended to be a living topic area, growing as new case studies are published. A database of all images from the website allows users to access larger resolution images and additional descriptive details. Logos clarify linkages among key contributors and assure users that the site is authoritative and science-based.

Relationships between waste physicochemical properties, microbial activity and vegetation at coal ash and sludge disposal sites.

PubMed

Woch, Marcin W; Radwańska, Magdalena; Stanek, Małgorzata; Łopata, Barbara; Stefanowicz, Anna M

2018-06-11

The aim of the study was to assess the relationships between vegetation, physicochemical and microbial properties of substrate at coal ash and sludge disposal sites. The study was performed on 32 plots classified into 7 categories: dried ash sedimentation ponds, dominated by a grass Calamagrostis epigejos (AH-Ce), with the admixture of Pinus sylvestris (AH-CePs) or Robinia pseudoacacia (AH-CeRp), dry ash landfill dominated by Betula pendula and Pinus sylvestris (AD-BpPs) or Salix viminalis (AD-Sv) and coal sludge pond with drier parts dominated by Tussilago farfara (CS-Tf) and the wetter ones by Cyperus flavescens (CS-Cf). Ash sites were covered with soil layer imported as a part of technical reclamation. Ash had relatively high concentrations of some alkali and alkaline earth metals, Mn and pH, while coal sludge had high water and C, S, P and K contents. Concentrations of heavy metals were lower than allowable limits in all substrate types. Microbial biomass and, particularly, enzymatic activity in ash and sludge were generally low. The only exception were CS-Tf plots characterized by the highest microbial biomass, presumably due to large deposits of organic matter that became available for aerobic microbial biomass when water level fell. The properties of ash and sludge adversely affected microbial biomass and enzymatic activity as indicated by significant negative correlations between the content of alkali/alkaline earth metals, heavy metals, and macronutrients with enzymatic activity and/or microbial biomass, as well as positive correlations of these parameters with metabolic quotient (qCO 2 ). Plant species richness and cover were relatively high, which may be partly associated with alleviating influence of soil covering the ash. The effect of the admixture of R. pseudoacacia or P. sylvestris to stands dominated by C. epigejos was smaller than expected. The former species increased NNH 4 , NNO 3 and arylsulfatase activity, while the latter reduced activity of the enzyme. Copyright © 2018 Elsevier B.V. All rights reserved.

Chemical and physical characteristics of coal and carbonaceous shale samples from the Salt Range coal field, Punjab Province, Pakistan

USGS Publications Warehouse

Warwick, Peter D.; Shakoor, T.; Javed, Shahid; Mashhadi, S.T.A.; Hussain, H.; Anwar, M.; Ghaznavi, M.I.

1990-01-01

Sixty coal and carbonaceous shale samples collected from the Paleocene Patala Formation in the Salt Range coal field, Punjab Province, Pakistan, were analyzed to examine the relationships between coal bed chemical and physical characteristics and depositional environments. Results of proximate and ultimate analyses, reported on an as received basis, indicate that coal beds have an average ash yield of 24.23 percent, average sulfur content of 5.32 percent, average pyritic sulfur content of 4.07 percent, and average calorific value of 8943 Btu (4972 kcal/kg). Thirty five coal samples, analyzed on a whole coal, dry basis for selected trace elements and oxides, have anomalously high average concentrations of Ti, at O.3& percent; Zr, at 382 ppm; and Se, at 11.4 ppm, compared to world wide averages for these elements in coal.Some positive correlation coefficients, significant at a 0.01 level, are those between total sulfur and As, pyritic sulfur and As, total sulfur and sample location, organic sulfur and Se, calorific value (Btu) and sample location, and coal bed thickness and Se. Calorific values -for the samples, calculated on a moist, mineral matter free basis, indicate that the apparent rank of the coal is high volatile C bituminous.Variations observed in the chemical and physical characteristics of the coal beds may be related to depositional environments. Total ash yields and concentrations of Se and organic sulfur increase toward more landward depositional environments and may be related to an increase of fluvial influence on peat deposition. Variations in pyritic sulfur concentrations may be related to post-peat pyrite filled burrows commonly observed in the upper part of the coal bed. The thickest coal beds that have the lowest ash content, and highest calorific values, formed from peats deposited in back barrier, tidal flat environments of the central and western parts of the coal field. The reasons for correlations between Se and coal bed thickness and Se and ash content are not clear and may be a product of averaging.

[Characterization of PAHs in fly ashes from coke production].

PubMed

Mu, Ling; Peng, Lin; Liu, Xiao-Feng; Bai, Hui-Ling; Zhang, Jian-Qiang

2013-03-01

In order to investigate the characteristics of polycyclic aromatic hydrocarbons (PAHs) in ashes from coking, PAHs in ashes from three coke production plants were analyzed with GC-MS, and the distribution characteristics of PAHs and potential toxicity risk were discussed. The sum of 16 EPA prior PAHs varied from 8.17 x 10(2) to 5.17 x 10(3) microg x g(-1). PAH contents from the coke oven (stamp charging) with the height of 3.2 m were two times higher than those from the one (top charging) with the height of 6.0 m, and PAHs in ashes from coal charging were significantly higher than those from coke pushing in the same plant. Four-ring and five-ring PAHs were the dominant species in ashes from coking and the sum of them accounted for more than 80.00% of total PAHs. Chrysene (Chr), benzo [a] anthracene (BaA) and benzo [b] fluoranthene (BbF) were abundant in all ash samples. The content of total BaP-based toxic equivalency (BaPeq) ranged from 1.64 x 10(2) to 9.57 x 10(2) microg x g(-1). From the carcinogenic point of view, besides benzo [a] pyrene (BaP), dibenz [a,h] anthracene (DbA) contributed most to the overall toxicity of PAHs, followed by BaA and BbF. BaPeq concentration from coal charging was 5.21-fold higher than that from coke pushing, indicating that different reuse ways should be considered based on their specific toxicity profiles of PAHs.

Physical and Chemical Properties of Bio-Oils From Microwave Pyrolysis of Corn Stover

NASA Astrophysics Data System (ADS)

Yu, Fei; Deng, Shaobo; Chen, Paul; Liu, Yuhuan; Wan, Yiqin; Olson, Andrew; Kittelson, David; Ruan, Roger

This study was aimed to understand the physical and chemical properties of pyrolytic bio-oils produced from microwave pyrolysis of corn stover regarding their potential use as gas turbine and home heating fuels. The ash content, solids content, pH, heating value, minerals, elemental ratio, moisture content, and viscosity of the bio-oils were determined. The water content was approx 15.2 wt%, solids content 0.22 wt%, alkali metal content 12 parts per million, dynamic viscosity 185 mPa·s at 40°C, and gross high heating value 17.5 MJ/kg for a typical bio-oil produced. Our aging tests showed that the viscosity and water content increased and phase separation occurred during the storage at different temperatures. Adding methanol and/or ethanol to the bio-oils reduced the viscosity and slowed down the increase in viscosity and water content during the storage. Blending of methanol or ethanol with the bio-oils may be a simple and cost-effective approach to making the pyrolytic bio-oils into a stable gas turbine or home heating fuels.

Physical and chemical properties of bio-oils from microwave pyrolysis of corn stover.

PubMed

Yu, Fei; Deng, Shaobo; Chen, Paul; Liu, Yuhuan; Wan, Yiqin; Olson, Andrew; Kittelson, David; Ruan, Roger

2007-04-01

This study was aimed to understand the physical and chemical properties of pyrolytic bio-oils produced from microwave pyrolysis of corn stover regarding their potential use as gas turbine and home heating fuels. The ash content, solids content, pH, heating value, minerals, elemental ratio, moisture content, and viscosity of the bio-oils were determined. The water content was approx 15.2 wt%, solids content 0.22 wt%, alkali metal content 12 parts per million, dynamic viscosity 185 mPa.s at 40 degrees C, and gross high heating value 17.5 MJ/kg for a typical bio-oil produced. Our aging tests showed that the viscosity and water content increased and phase separation occurred during the storage at different temperatures. Adding methanol and/or ethanol to the bio-oils reduced the viscosity and slowed down the increase in viscosity and water content during the storage. Blending of methanol or ethanol with the bio-oils may be a simple and cost-effective approach to making the pyrolytic bio-oils into a stable gas turbine or home heating fuels.

Aerosols from the soufriere eruption plume of 17 april 1979.

PubMed

Sedlacek, W A; Heiken, G; Zoller, W H; Germani, M S

1982-06-04

Aerosol samples collected from the 17 April 1979 eruption plume of Soufriere, St. Vincent, at altitudes between 1.8 and 5.5 kilometers were physically and chemically very similar to the ash that fell on the island. Higher altitude samples (7.3 and 9.5 kilometers) had a much lower ash content but comparable concentrations of sulfate, which were above the background concentration found at these altitudes.

Aerosols from the Soufriere eruption plume of 17 April 1979

NASA Technical Reports Server (NTRS)

Sedlacek, W. A.; Heiken, G.; Zoller, W. H.; Germani, M. S.

1982-01-01

Aerosol samples collected from the April 17, 1979 eruption plume of Soufriere, St. Vincent, at altitudes between 1.8 and 5.5 kilometers were physically and chemically very similar to the ash that fell on the island. Higher altitude samples (7.3 and 9.5 kilometers) had a much lower ash content but comparable concentrations of sulfate, which were above the background concentration found at these altitudes.

Results of the use of a system for continuous measurement of combustibles in the fly ash produced by burning of anthracite fines in a TPP-210A boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.A. Fil; L.V. Golyshev; I.S. Mysak

2002-11-15

Data on the use of RCA-2000 (Mark & Vedell, Denmark) stationary analyzers of the content of combustibles in fly ash for optimizing the furnace performance of a TPP-210A boiler and determining the effect of process switchings of the boiler equipment on the quality of the furnace performance are presented.

Effect of CO2 levels on nutrient content of lettuce and radish.

PubMed

McKeehen, J D; Smart, D J; Mackowiak, C L; Wheeler, R M; Nielsen, S S

1996-01-01

Atmospheric carbon-dioxide enrichment is known to affect the yield of lettuce and radish grown in controlled environments, but little is known about CO2 enrichment effects on the chemical composition of lettuce and radish. These crops are useful model systems for a Controlled Ecological Life-Support System (CELSS), largely because of their relatively short production cycles. Lettuce (Lactuca sativa L.) cultivar 'Waldmann's Green' and radish (Raphanus sativus L.) cultivar 'Giant White Globe' were grown both in the field and in controlled environments, where hydroponic nutrient solution, light, and temperature were regulated, and where CO2 levels were controlled at 400, 1000, 5000, or 10,000 ppm. Plants were harvested at maturity, dried, and analyzed for proximate composition (protein, fat, ash, and carbohydrate), total nitrogen (N), nitrate N, free sugars, starch, total dietary fiber, and minerals. Total N, protein N, nonprotein N (NPN), and nitrate N generally increased for radish roots and lettuce leaves when grown under growth chamber conditions compared to field conditions. The nitrate-N level of lettuce leaves, as a percentage of total NPN, decreased with increasing levels of CO2 enrichment. The ash content of radish roots and of radish and lettuce leaves decreased with increasing levels of CO2 enrichment. The levels of certain minerals differed between field- and chamber-grown materials, including changes in the calcium (Ca) and phosphorus (P) contents of radish and lettuce leaves, resulting in reduced Ca/P ratio for chamber-grown materials. The free-sugar contents were similar between the field and chamber-grown lettuce leaves, but total dietary fiber content was much higher in the field-grown plant material. The starch content of growth-chamber lettuce increased with CO2 level.

Effect of CO_2 levels on nutrient content of lettuce and radish

NASA Astrophysics Data System (ADS)

McKeehen, J. D.; Smart, D. J.; Mackowiak, C. L.; Wheeler, R. M.; Nielsen, S. S.

Atmospheric carbon-dioxide enrichment is known to affect the yield of lettuce and radish grown in controlled environments, but little is known about CO_2 enrichment effects on the chemical composition of lettuce and radish. These crops are useful model systems for a Controlled Ecological Life-Support System (CELSS), largely because of their relatively short production cycles. Lettuce (Lactuca sativa L.) cultivar `Waldmann's Green' and radish (Raphanus sativus L.) cultivar `Giant White Globe' were grown both in the field and in controlled environments, where hydroponic nutrient solution, light, and temperature were regulated, and where CO_2 levels were controlled at 400, 1000, 5000, or 10,000 ppm. Plants were harvested at maturity, dried, and analyzed for proximate composition (protein, fat, ash, and carbohydrate), total nitrogen (N), nitrate N, free sugars, starch, total dietary fiber, and minerals. Total N, protein N, nonprotein N (NPN), and nitrate N generally increased for radish roots and lettuce leaves when grown under growth chamber conditions compared to field conditions. The nitrate-N level of lettuce leaves, as a percentage of total NPN, decreased with increasing levels of CO_2 enrichment. The ash content of radish roots and of radish and lettuce leaves decreased with increasing levels of CO_2 enrichment. The levels of certain minerals differed between field- and chamber-grown materials, including changes in the calcium (Ca) and phosphorus (P) contents of radish roots and lettuce leaves, resulting in reduced Ca/P ratio for chamber-grown materials. The free-sugar contents were similar between the field and chamber-grown lettuce leaves, but total dietary fiber content was much higher in the field-grown plant material. The starch content of growth-chamber lettuce increased with CO_2 level.

Effect of CO2 levels on nutrient content of lettuce and radish

NASA Technical Reports Server (NTRS)

McKeehen, J. D.; Smart, D. J.; Mackowiak, C. L.; Wheeler, R. M.; Nielsen, S. S.; Mitchell, C. A. (Principal Investigator)

1996-01-01

Atmospheric carbon-dioxide enrichment is known to affect the yield of lettuce and radish grown in controlled environments, but little is known about CO2 enrichment effects on the chemical composition of lettuce and radish. These crops are useful model systems for a Controlled Ecological Life-Support System (CELSS), largely because of their relatively short production cycles. Lettuce (Lactuca sativa L.) cultivar 'Waldmann's Green' and radish (Raphanus sativus L.) cultivar 'Giant White Globe' were grown both in the field and in controlled environments, where hydroponic nutrient solution, light, and temperature were regulated, and where CO2 levels were controlled at 400, 1000, 5000, or 10,000 ppm. Plants were harvested at maturity, dried, and analyzed for proximate composition (protein, fat, ash, and carbohydrate), total nitrogen (N), nitrate N, free sugars, starch, total dietary fiber, and minerals. Total N, protein N, nonprotein N (NPN), and nitrate N generally increased for radish roots and lettuce leaves when grown under growth chamber conditions compared to field conditions. The nitrate-N level of lettuce leaves, as a percentage of total NPN, decreased with increasing levels of CO2 enrichment. The ash content of radish roots and of radish and lettuce leaves decreased with increasing levels of CO2 enrichment. The levels of certain minerals differed between field- and chamber-grown materials, including changes in the calcium (Ca) and phosphorus (P) contents of radish and lettuce leaves, resulting in reduced Ca/P ratio for chamber-grown materials. The free-sugar contents were similar between the field and chamber-grown lettuce leaves, but total dietary fiber content was much higher in the field-grown plant material. The starch content of growth-chamber lettuce increased with CO2 level.

Dioxins reformation and destruction in secondary copper smelting fly ash under ball milling

PubMed Central

Cagnetta, Giovanni; Hassan, Mohammed Mansour; Huang, Jun; Yu, Gang; Weber, Roland

2016-01-01

Secondary copper recovery is attracting increasing interest because of the growth of copper containing waste including e-waste. The pyrometallurgical treatment in smelters is widely utilized, but it is known to produce waste fluxes containing a number of toxic pollutants due to the large amount of copper involved, which catalyses the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (“dioxins”). Dioxins are generated in secondary copper smelters on fly ash as their major source, resulting in highly contaminated residues. In order to assess the toxicity of this waste, an analysis of dioxin-like compounds was carried out. High levels were detected (79,090 ng TEQ kg−1) in the ash, above the Basel Convention low POPs content (15,000 ng TEQ kg−1) highlighting the hazardousness of this waste. Experimental tests of high energy ball milling with calcium oxide and silica were executed to assess its effectiveness to detoxify such fly ash. Mechanochemical treatment obtained 76% dioxins reduction in 4 h, but longer milling time induced a partial de novo formation of dioxins catalysed by copper. Nevertheless, after 12 h treatment the dioxin content was substantially decreased (85% reduction) and the copper, thanks to the phenomena of incorporation and amorphization that occur during milling, was almost inactivated. PMID:26975802

Mechanical properties and microstructure analysis of fly ash geopolymeric recycled concrete.

PubMed

Shi, X S; Collins, F G; Zhao, X L; Wang, Q Y

2012-10-30

Six mixtures with different recycled aggregate (RA) replacement ratios of 0%, 50% and 100% were designed to manufacture recycled aggregate concrete (RAC) and alkali-activated fly ash geopolymeric recycled concrete (GRC). The physical and mechanical properties were investigated indicating different performances from each other. Optical microscopy under transmitted light and scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX) were carried out in this study in order to identify the mechanism underlying the effects of the geopolymer and RA on concrete properties. The features of aggregates, paste and interfacial transition zone (ITZ) were compared and discussed. Experimental results indicate that using alkali-activated fly ash geopolymer as replacement of ordinary Portland cement (OPC) effectively improved the compressive strength. With increasing of RA contents in both RAC and GRC, the compressive strength decreased gradually. The microstructure analysis shows that, on one hand, the presence of RA weakens the strength of the aggregates and the structure of ITZs; on the other hand, due to the alkali-activated fly ash in geopolymer concrete, the contents of Portlandite (Ca(OH)(2)) and voids were reduced, as well as improved the matrix homogeneity. The microstructure of GRC was changed by different reaction products, such as aluminosilicate gel. Copyright © 2012 Elsevier B.V. All rights reserved.

Dioxins reformation and destruction in secondary copper smelting fly ash under ball milling

NASA Astrophysics Data System (ADS)

Cagnetta, Giovanni; Hassan, Mohammed Mansour; Huang, Jun; Yu, Gang; Weber, Roland

2016-03-01

Secondary copper recovery is attracting increasing interest because of the growth of copper containing waste including e-waste. The pyrometallurgical treatment in smelters is widely utilized, but it is known to produce waste fluxes containing a number of toxic pollutants due to the large amount of copper involved, which catalyses the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (“dioxins”). Dioxins are generated in secondary copper smelters on fly ash as their major source, resulting in highly contaminated residues. In order to assess the toxicity of this waste, an analysis of dioxin-like compounds was carried out. High levels were detected (79,090 ng TEQ kg-1) in the ash, above the Basel Convention low POPs content (15,000 ng TEQ kg-1) highlighting the hazardousness of this waste. Experimental tests of high energy ball milling with calcium oxide and silica were executed to assess its effectiveness to detoxify such fly ash. Mechanochemical treatment obtained 76% dioxins reduction in 4 h, but longer milling time induced a partial de novo formation of dioxins catalysed by copper. Nevertheless, after 12 h treatment the dioxin content was substantially decreased (85% reduction) and the copper, thanks to the phenomena of incorporation and amorphization that occur during milling, was almost inactivated.

Environmentally critical elements in channel and cleaned samples of Illinois coals

USGS Publications Warehouse

Demir, I.; Ruch, R.R.; Damberger, H.H.; Harvey, R.D.; Steele, J.D.; Ho, K.K.

1998-01-01

Sixteen trace and minor elements that occur in coal are listed among 189 substances identified as 'hazardous air pollutants' (HAPs) in the US Clean Air Act Amendments of 1990. We investigated the occurrence and cleanability of the 16 HAPs in Illinois coals, as a contribution to the discussion about the potential effect of pending environmental regulations on the future use of these coals in power generation. The average ash content of the samples of conventionally cleaned as-shipped coals is about 20% lower than that of standard channel samples. Conventional cleaning reduces the average concentrations of As, Cd, Co, Hg, Mn, Ni, Pb, Sb and Th in the as-shipped coals by more than 20% relative to channel samples. Thus, basing assessments of health risks from emissions of HAPs during coal combustion on channel samples without appropriate adjustment would overestimate the risk. Additional cleaning by froth-flotation reduces the ash content of finely-ground as-shipped coals by as much as 76% at an 80% combustibles recovery. Although the average froth-flotation cleanability for the majority of HAPs is less than that for ash, the cleanabilities in some individual cases approaches, or even exceeds, the cleanability for ash, depending on the modes of occurrences of the elements. ?? 1997 Elsevier Science Ltd.

Hydrothermal liquefaction of harvested high-ash low-lipid algal biomass from Dianchi Lake: effects of operational parameters and relations of products.

PubMed

Tian, Chunyan; Liu, Zhidan; Zhang, Yuanhui; Li, Baoming; Cao, Wei; Lu, Haifeng; Duan, Na; Zhang, Li; Zhang, Tingting

2015-05-01

Hydrothermal liquefaction (HTL) allows a direct conversion of algal biomass into biocrude oil, not only solving the environmental issues caused by the over-growing algae but also producing renewable energy. This study reports HTL of algae after separation from eutrophicated Dianchi Lake in China. Conversion efficiency was studied under different operational conditions via an orthogonal design, including holding temperature (HT) (260-340 °C), retention time (RT) (30-90 min) and total solid (TS) (10-20%). A highest biocrude oil yield (18.4%, dry ash-free basis, daf) was achieved at 300 °C, 60 min, and 20% (TS), due to the low contents of lipids (1.9%, daf) and proteins (24.8%, daf), and high contents of ash (41.6%, dry basis) and carbohydrates (71.8%, daf). Operational parameters significantly affected the biocrude yields, and chemical distribution of HTL products. The biocrude production also related to other HTL products, and involved chemical reactions, such as deoxygenation and/or denitrogenation. Copyright © 2014 Elsevier Ltd. All rights reserved.

A pilot and field investigation on mobility of PCDDs/PCDFs in landfill site with municipal solid waste incineration residue.

PubMed

Osako, Masahiro; Kim, Yong-Jin; Lee, Dong-Hoon

2002-09-01

A field investigation by boring was carried out in a landfill site primarily with municipal solid waste incineration residue. From the collected core samples, vertical profiles of homologous content of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) in the landfill layer were traced and the behavior of PCDDs/PCDFs was examined. In addition, a pilot-scale study was conducted on the PCDDs/PCDFs leached from incineration fly ash and the treated one using large landfill simulation columns (lysimeters) and the leaching behavior of PCDDs/PCDFs was examined. As a result, it was found that the coexistence of dissolved coloring constituents (DCCs), which might be composed of constituents like dissolved humic matters having strong affinity for hydrophobic organic pollutants, could enhance the leachability of PCDDs/PCDFs, thus contributing to the vertical movement and leaching behavior of PCDDs/PCDFs in the landfill layers of the incineration residue. Moreover, it is highly probable that DCCs derive from the unburned carbon in the bottom ash mixed and buried with the fly ash containing a high content of PCDDs/PCDFs.

Enhancing the use of waste activated sludge as bio-fuel through selectively reducing its heavy metal content.

PubMed

Dewil, Raf; Baeyens, Jan; Appels, Lise

2007-06-18

Power plant or cement kiln co-incineration are important disposal routes for the large amounts of waste activated sludge (WAS) which are generated annually. The presence of significant amounts of heavy metals in the sludge however poses serious problems since they are partly emitted with the flue gases (and collected in the flue gas dedusting) and partly incorporated in the ashes of the incinerator: in both cases, the disposal or reuse of the fly ash and bottom ashes can be jeopardized since subsequent leaching in landfill disposal can occur, or their "pozzolanic" incorporation in cement cannot be applied. The present paper studies some physicochemical methods for reducing the heavy metal content of WAS. The used techniques include acid and alkaline thermal hydrolysis and Fenton's peroxidation. By degrading the extracellular polymeric substances, binding sites for a large amount of heavy metals, the latter are released into the sludge water. The behaviour of several heavy metals (Cd, Cr, Cu, Hg, Pb, Ni, Zn) was assessed in laboratory tests. Results of these show a significant reduction of most heavy metals.

Composition and quality of coals in the Huaibei Coalfield, Anhui, China

USGS Publications Warehouse

Zheng, Lingyun; Liu, Gaisheng; Wang, L.; Chou, C.-L.

2008-01-01

The Huaibei Coalfield, Anhui Province, China, is one of the largest coalfields in China. The coals of Permian age are used mainly for power generation. Coal compositions and 47 trace elements of the No. 10 Coal of the Shanxi Formation, the No. 7, 5, and 4 Coals of the Lower Shihezi Formation, and the No. 3 Coal of the Upper Shihezi Formation from the Huaibei Coalfield were studied. The results indicate that the Huaibei coals have low ash, moisture, and sulfur contents, but high volatile matter and calorific value. The ash yield increases stratigraphically upwards, but the volatile matter and total sulfur contents show a slight decrease from the lower to upper seams. Magmatic intrusion into the No. 5 Coal resulted in high ash, volatile matter, and calorific value, but low moisture value in the coal. Among the studied 47 trace elements, Ba, Co, Cr, Cu, Hg, Mo, Ni, Pb, Sb, Th, U, V, and Zn are of environmental concerns. Four elements Hg, Mo, Zn, and Sb are clearly enriched in the coals as compared with the upper continental crust. ?? 2007 Elsevier B.V. All rights reserved.

Impact of animal density on cattle nutrition in dry Mediterranean rangelands: a faecal near-IR spectroscopy-aided study.

PubMed

Landau, S Y; Dvash, L; Yehuda, Y; Muklada, H; Peleg, G; Henkin, Z; Voet, H; Ungar, E D

2018-02-01

In the context of determining the sustainable carrying capacity of dry-Mediterranean herbaceous rangelands, we examined the effect of animal density on cattle nutrition, which is fundamental to animal performance and welfare. The effects on dietary components of low (0.56 cows/ha; L) and high (1.11 cows/ha; H) animal densities were monitored for three consecutive years in grazing beef cows. In the dry season (summer and early autumn), cows had free access to N-rich poultry litter (PL) given as a dietary supplement. In each season, near-IR spectroscopy (NIRS) was used to predict the chemical composition of herbage samples (ash, NDF, CP, in vitro dry matter digestibility (IVDMD) and metabolizable energy (ME) content from IVDMD). Near-IR spectroscopy was applied also to faecal samples to determine the chemical composition of the diet selected by the animal, as well as the contents of ash, NDF and CP in the faeces themselves. A faecal-NIRS equation was applied to estimate the dietary proportion of PL. Seasonal categories were green, dry without PL supplementation and dry with it. We found no effects of animal density on nutrition during the green season but effects were apparent when cows consumed dry pasture. Ash content predicted by faecal NIRS was higher in the diet than in plant samples clipped from pasture, which infers that cows ingested soil. Dietary and faecal ash contents were higher (P<0.05) at the H, implying greater soil intake in these animals. During the dry period, dietary contents of ME were higher in L than in H (P<0.05). Poultry litter supplementation was associated with a marked increase (P<0.01) in dietary and faecal CP contents. Poultry litter represented 0.45 and 0.59 of the diet in treatments L and H, respectively (P<0.05). Consequently, treatment H had higher faecal protein (P<0.05). A tendency of higher dietary protein (P=0.08) and lower dietary NDF (P=0.10) in treatment H was probably related to greater PL ingestion. Given that high and sustained rates of poultry litter consumption are detrimental to animal health, the above results cast doubts on the long-term sustainability of the higher of the animal densities tested. Although it may be sustainable vis-à-vis the vegetation, treatment H may have exceeded the boundaries of what is acceptable for cow health. Chemical information revealed with NIRS can be used to evaluate whether animal densities are compatible with animal health and welfare standards and can play a role in determining the carrying capacity of Mediterranean rangelands.

Integrated coal cleaning, liquefaction, and gasification process

DOEpatents

Chervenak, Michael C.

1980-01-01

Coal is finely ground and cleaned so as to preferentially remove denser ash-containing particles along with some coal. The resulting cleaned coal portion having reduced ash content is then fed to a coal hydrogenation system for the production of desirable hydrocarbon gases and liquid products. The remaining ash-enriched coal portion is gasified to produce a synthesis gas, the ash is removed from the gasifier usually as slag, and the synthesis gas is shift converted with steam and purified to produce the high purity hydrogen needed in the coal hydrogenation system. This overall process increases the utilization of as-mined coal, reduces the problems associated with ash in the liquefaction-hydrogenation system, and permits a desirable simplification of a liquids-solids separation step otherwise required in the coal hydrogenation system.

Chronology and pyroclastic stratigraphy of the May 18, 1980, eruption of Mount St. Helens, Washington

NASA Technical Reports Server (NTRS)

Criswell, C. William

1987-01-01

The eruption of Mount St. Helens on May 18, 1980 can be subdivided into six phases: the paroxysmal phase I, the early Plinian phase II, the early ash flow phase III, the climactic phase IV, the late ash flow phase V, and phase VI, the activity of which consisted of a low-energy ash plume. These phases are correlated with stratigraphic subunits of ash-fall tephra and pyroclastic flow deposits. Sustained vertical discharge of phase II produced evolved dacite with high S/Cl ratios. Ash flow activity of phase III is attributed to decreases in gas content, indicated by reduced S/Cl ratios and increased clast density of the less evolved gray pumice. Climactic events are attributed to vent clearing and exhaustion of the evolved dacite.

Coal-oil slurry preparation

DOEpatents

Tao, John C.

1983-01-01

A pumpable slurry of pulverized coal in a coal-derived hydrocarbon oil carrier which slurry is useful as a low-ash, low-sulfur clean fuel, is produced from a high sulfur-containing coal. The initial pulverized coal is separated by gravity differentiation into (1) a high density refuse fraction containing the major portion of non-coal mineral products and sulfur, (2) a lowest density fraction of low sulfur content and (3) a middlings fraction of intermediate sulfur and ash content. The refuse fraction (1) is gasified by partial combustion producing a crude gas product from which a hydrogen stream is separated for use in hydrogenative liquefaction of the middlings fraction (3). The lowest density fraction (2) is mixed with the liquefied coal product to provide the desired fuel slurry. Preferably there is also separately recovered from the coal liquefaction LPG and pipeline gas.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, W.J.; DeMaris, P.J.; Bauer, R.A.

One of the largest deposits of low-sulfur coal in the Illinois Basin is in the so-called Hornsby District of Christian, Macoupin, and Montgomery Counties. An estimated resource of 1.17 billion tons of Herrin (No. 6) Coal, containing less than 2.5% sulfur, occurs here. Although the Hornsby deposit is thick, lies at moderate depth, and is close to market and labor supply, it has been barely touched by mining. The primary deterrent to mining this high-quality product has been fear of unstable roof conditions. Low-sulfur Hornsby coal contains about 1.5% less ash and 2% more moisture than does adjacent high-sulfur coal.more » The lower ash content probably reflects scarcity of pyrite. The reason for the difference in moisture content is unknown. High- and low-sulfur coal are nearly identical in heating value.« less

Extraction of silica content from the Cymbopogan citratus (lemon grass) and its performance as reinforcement for polymers

NASA Astrophysics Data System (ADS)

Firdaus, M. Y. Nur; Osman, H.; Metselaar, H. S. C.; Rozyanty, A. R.

2017-07-01

Silica is widely used as sources for adsorption materials, medical additives and fillers in composite and rubber industries. The manufacturing process of commercial silica use in various industries is very expensive and energy extensive. Therefore, agricultural waste material such as lemon grass is seen as a potential alternative silica sources for replacement of commercial silica which is currently available in the industry. In this research, a simple method based on the acid leaching treatment with hydrochloric acid (HCl) was developed to produce purified silica from lemon grass, followed by thermal combustion at 600°C. Acid leaching temperatures of 33, 50, 80 and 110°C were used. The silica content, shape and texture of the lemon grass ash was characterized using scanning electron microcopy -energy-dispersive X-ray (SEM-EDX) analysis. The SEM analysis indicated the presence of tubular-shaped porous aggregates, spherical and fibrous shapes of untreated and treated lemon grass at 33°C to 110 °C. The highest silica content recorded was 73.46% for lemon grass treated at the highest leaching temperature of 110°C. The thermal stability of lemon grass ash was examined by using a thermogravimetric analysis (TGA) instrument. The TGA analysis shows that the untreated and treated lemon grass ash start to decompose at lower temperature (90 to 100°C). Lemon grass treated at the highest leaching temperature 110°C exhibit the highest thermal stability.

Physicochemical characterizations of nano-palm oil fuel ash

NASA Astrophysics Data System (ADS)

Rajak, Mohd Azrul Abdul; Majid, Zaiton Abdul; Ismail, Mohammad

2015-07-01

Palm Oil Fuel Ash (POFA) is known as a good supplementary cementing material due to its siliceous-rich content. The application of nanotechnology in the pozzolanic materials could invent new functions in the efficiency of physical and chemical properties of materials. Thus, the present study aims to generate nano-sized POFA and characterize the physicochemical properties of nano-palm oil fuel ash (nPOFA). The nPOFA was prepared by mechanically grinding micro POFA using a high intensity ball milling for 6 hours. The physicochemical properties of nPOFA were characterized via X-Ray Fluoresence (XRF), Scanning Emission microscopy- Energy Dispersive X-Ray (SEM-EDX), Transmission Electron Microscope (TEM) and X-Ray Diffraction (XRD). The particle size of nPOFA acquired from TEM analysis was in the range of 20 nm to 90 nm, while the average crystallite size calculated from XRD diffractogram was 61.5 nm. The resulting nPOFA has a BET surface area of 145.35 m2/g, which is more than 85% increment in surface area compared to micro-sized POFA. The morphology and elemental studies showed the presence of spherical as well as irregularly shaped and fine nPOFA particles contains with high silicon content. The presence of α-quartz as the major phase of the nPOFA was identified through XRD analysis. The study concludes that nPOFA has the potential as a supplementary cementing material due to the high silica content, high surface area and the unique behaviors of nano-structured particles.

Heterogeneous Ice Nucleation by Soufriere Hills Volcanic Ash Immersed in Water Droplets.

PubMed

Mangan, T P; Atkinson, J D; Neuberg, J W; O'Sullivan, D; Wilson, T W; Whale, T F; Neve, L; Umo, N S; Malkin, T L; Murray, B J

2017-01-01

Fine particles of ash emitted during volcanic eruptions may sporadically influence cloud properties on a regional or global scale as well as influencing the dynamics of volcanic clouds and the subsequent dispersion of volcanic aerosol and gases. It has been shown that volcanic ash can trigger ice nucleation, but ash from relatively few volcanoes has been studied for its ice nucleating ability. In this study we quantify the efficiency with which ash from the Soufriere Hills volcano on Montserrat nucleates ice when immersed in supercooled water droplets. Using an ash sample from the 11th February 2010 eruption, we report ice nucleating efficiencies from 246 to 265 K. This wide range of temperatures was achieved using two separate droplet freezing instruments, one employing nanolitre droplets, the other using microlitre droplets. Soufriere Hills volcanic ash was significantly more efficient than all other ash samples that have been previously examined. At present the reasons for these differences are not understood, but may be related to mineralogy, amorphous content and surface chemistry.

Heterogeneous Ice Nucleation by Soufriere Hills Volcanic Ash Immersed in Water Droplets

PubMed Central

Atkinson, J. D.; Neuberg, J. W.; O’Sullivan, D.; Wilson, T. W.; Whale, T. F.; Neve, L.; Umo, N. S.; Malkin, T. L.; Murray, B. J.

2017-01-01

Fine particles of ash emitted during volcanic eruptions may sporadically influence cloud properties on a regional or global scale as well as influencing the dynamics of volcanic clouds and the subsequent dispersion of volcanic aerosol and gases. It has been shown that volcanic ash can trigger ice nucleation, but ash from relatively few volcanoes has been studied for its ice nucleating ability. In this study we quantify the efficiency with which ash from the Soufriere Hills volcano on Montserrat nucleates ice when immersed in supercooled water droplets. Using an ash sample from the 11th February 2010 eruption, we report ice nucleating efficiencies from 246 to 265 K. This wide range of temperatures was achieved using two separate droplet freezing instruments, one employing nanolitre droplets, the other using microlitre droplets. Soufriere Hills volcanic ash was significantly more efficient than all other ash samples that have been previously examined. At present the reasons for these differences are not understood, but may be related to mineralogy, amorphous content and surface chemistry. PMID:28056077

Ability of natural attenuation and phytoremediation using maize (Zea mays L.) to decrease soil contents of polycyclic aromatic hydrocarbons (PAHs) derived from biomass fly ash in comparison with PAHs-spiked soil.

PubMed

Košnář, Zdeněk; Mercl, Filip; Tlustoš, Pavel

2018-05-30

A 120-day pot experiment was conducted to compare the ability of natural attenuation and phytoremediation approaches to remove polycyclic aromatic hydrocarbons (PAHs) from soil amended with PAHs-contaminated biomass fly ash. The PAH removal from ash-treated soil was compared with PAHs-spiked soil. The removal of 16 individual PAHs from soil ranged between 4.8% and 87.8% within the experiment. The natural attenuation approach led to a negligible total PAH removal. The phytoremediation was the most efficient approach for PAH removal, while the highest removal was observed in the case of ash-treated soil. The content of low molecular weight (LMW) PAHs and the total PAHs in this treatment significantly decreased (P <.05) over the whole experiment by 47.6% and 29.4%, respectively. The tested level of PAH soil contamination (~1600 µg PAH/kg soil dry weight) had no adverse effects on maize growth as well on the biomass yield. In addition, the PAHs were detected only in maize roots and their bioaccumulation factors were significantly lower than 1 suggesting negligible PAH uptake from soil by maize roots. The results showed that PAHs of ash origin were similarly susceptible to removal as spiked PAHs. The presence of maize significantly boosted the PAH removal from soil and its aboveground biomass did not represent any environmental risk. Copyright © 2018 Elsevier Inc. All rights reserved.

Phytoextraction of metals by Erigeron canadensis L. from fly ash landfill of power plant "Kolubara".

PubMed

Krgović, Rada; Trifković, Jelena; Milojković-Opsenica, Dušanka; Manojlović, Dragan; Marković, Marijana; Mutić, Jelena

2015-07-01

The objectives of this study were to determine the concentrations of Pb, Cd, As, Cr, Cu, Co, Ni, Zn, Ba, Fe, Al and Ag in Erigeron canadensis L. growing on fly ash landfill of power plant "Kolubara", Serbia. The content of each element was determined in every part of plant separately (root, stalk and inflorescence) and correlated with the content of elements in each phase of sequential extraction of fly ash. In order to ambiguously select the factors that are able to decidedly characterize the particular part of plant, principal component analysis (PCA) and partial least squares discriminant analysis (PLS-DA) were performed. The bioconcentration factors and translocation factors for each metal were calculated in order to determine the feasibility of the use of plant E. canadensis L. for phytoremediation purpose. There were strong positive correlations between metals in every part of plant samples, and metals from pseudo total form of sequential extraction indicate that the bioavailability of elements in fly ash is similarly correlated with total form. Retained Al, Fe, Cr and Co in the root indicate its suitability for phytostabilization. This plant takes up Cd and Zn from the soil (bioconcentration factors (BCFs) greater than 1), transporting them through the stalk into the inflorescence (translocation factors (TFs) higher than 1). Regarding its dominance in vegetation cover and abundance, E. canadensis L. can be considered adequate for phytoextraction of Cd and Zn from coal ash landfills at Kolubara.

Arab light crude study focuses on kinematic viscosity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beg, S.A.; Al-Mutawa, A.H.; Amin, M.B.

1989-02-01

Arab light crude oil has been characterized in terms of API gravity, total sulfur content, Reid vapor pressure, ash content, heating value, salt content, viscosity SUS, vanadium content as V/sub 2/O/sub 5/, pour point and analyses of various metals. The crude oil was fractionated into six true boiling point (TBP) fractions (IBP-95/sup 0/C, 95-205/sup 0/C, 205-260/sup 0/C, 260-345/sup 0/C, 345-455/sup 0/C and 455/sup 0/C+). These fractions were characterized in terms of API gravity, total sulfur, H/sub 2/S, mercaptan contents, molecular weight, elemental analyses for total carbon, hydrogen and nitrogen, and analyses of various metals. The kinematic viscosity data have beenmore » obtained for 95/sup 0/C+ TBP fractions for a wide range of temperature up to 200/sup 0/C.« less

Physical-durable performance of concrete incorporating high loss on ignition-fly ash

NASA Astrophysics Data System (ADS)

Huynh, Trong-Phuoc; Ngo, Si-Huy; Hwang, Chao-Lung

2018-04-01

This study investigates the feasibility of using raw fly ash with a high loss on ignition in concrete. The fly ash-free concrete samples were prepared with different water-to-binder (w/b) ratios of 0.35, 0.40, and 0.45, whereas the fly ash concrete samples were prepared with a constant w/b of 0.40 and with various fly ash contents (10%, 20%, and 30%) as a cement substitution. The physical properties and durability performance of the concretes were evaluated through fresh concrete properties, compressive strength, strength efficiency of cement, ultrasonic pulse velocity, and resistance to sulfate attack. Test results show that the w/b ratio affected the concrete properties significantly. The incorporation of fly ash increased the workability and reduced the unit weight of fresh concrete. In addition, the fly ash concrete samples containing up to 20% fly ash exhibited an improved strength at long-term ages. Further, all of the fly ash concrete samples showed a good durability performance with ultrasonic pulse velocity value of greater than 4100 m/s and a comparable sulfate resistance to the no-fly ash concrete.

Prediction of the true digestible amino acid contents from the chemical composition of sorghum grain for poultry.

PubMed

Ebadi, M R; Sedghi, M; Golian, A; Ahmadi, H

2011-10-01

Accurate knowledge of true digestible amino acid (TDAA) contents of feedstuffs is necessary to accurately formulate poultry diets for profitable production. Several experimental approaches that are highly expensive and time consuming have been used to determine available amino acids. Prediction of the nutritive value of a feed ingredient from its chemical composition via regression methodology has been attempted for many years. The artificial neural network (ANN) model is a powerful method that may describe the relationship between digestible amino acid contents and chemical composition. Therefore, multiple linear regressions (MLR) and ANN models were developed for predicting the TDAA contents of sorghum grain based on chemical composition. A precision-fed assay trial using cecectomized roosters was performed to determine the TDAA contents in 48 sorghum samples from 12 sorghum varieties differing in chemical composition. The input variables for both MLR and ANN models were CP, ash, crude fiber, ether extract, and total phenols whereas the output variable was each individual TDAA for every sample. The results of this study revealed that it is possible to satisfactorily estimate the TDAA of sorghum grain through its chemical composition. The chemical composition of sorghum grain seems to highly influence the TDAA contents when considering components such as CP, crude fiber, ether extract, ash and total phenols. It is also possible to estimate the TDAA contents through multiple regression equations with reasonable accuracy depending on composition. However, a more satisfactory prediction may be achieved via ANN for all amino acids. The R(2) values for the ANN model corresponding to testing and training parameters showed a higher accuracy of prediction than equations established by the MLR method. In addition, the current data confirmed that chemical composition, often considered in total amino acid prediction, could be also a useful predictor of true digestible values of selected amino acids for poultry.

Physicochemical, pasting, and functional properties of amaranth seed flours: effects of lipids removal.

PubMed

Shevkani, Khetan; Singh, Narpinder; Kaur, Amritpal; Rana, Jai Chand

2014-07-01

The present work was carried out to evaluate physicochemical (composition, hunter color, and sodium dodecyl sulfate-polyacrylamide gel electrophoresis [SDS-PAGE]), pasting, and functional properties (foaming, emulsification, water, and fat absorption capacity) of amaranth full-fat flours from 6 lines/cultivars (AFs), and to see the effects of lipid removal/defatting on these properties. Protein, ash, and lipid content of AFs ranged between 12.5% to 15.2%, 3.0% to 3.5%, and 7.1% to 8.0%, respectively. The flours showed a number of bands between 97 and 7 kDa, with main subunits of approximately 58, 37, 33, 31, 23, and 16 kDa in the SDS-PAGE profiles. The protein content and L* value increased, while b* values decreased following defatting for most of the lines/cultivars. The defatted flours (DAFs) had higher final viscosity and stability (lower breakdown viscosity) as compared to counterpart AFs. The protein profiling of the flours was not affected with the lipid removal/defatting. However, water absorption capacity and foam stability of the flours improved upon defatting. Principal component analysis revealed that pasting temperature was positively related to lipid content, while breakdown viscosity was negatively related to protein content. Foaming properties (capacity and stability) showed negative relationship with lipid content, and positive with protein content, ash content, water, and fat absorption capacity. Amaranth grains are known to have higher amount of proteins and lipids than cereals. Amaranth lipids are rich in unsaturated fatty acids, which are prone to oxidative rancidity. Removal of lipids or defatting of flours may be carried out to enhance product shelf life by preventing undesirable oxidative chain reactions. Therefore, this research was undertaken to see the effects of defatting on the functional properties of amaranth flours. The defatting was a value addition process as it improved the functional properties of the flours. © 2014 Institute of Food Technologists®

Effects of replacing pork back fat with vegetable oils and rice bran fiber on the quality of reduced-fat frankfurters.

PubMed

Choi, Yun-Sang; Choi, Ji-Hun; Han, Doo-Jeong; Kim, Hack-Youn; Lee, Mi-Ai; Jeong, Jong-Youn; Chung, Hai-Jung; Kim, Cheon-Jei

2010-03-01

The effects of substituting olive, grape seed, corn, canola, or soybean oil and rice bran fiber on the chemical composition, cooking characteristics, fatty acid composition, and sensory properties of low-fat frankfurters were investigated. Ten percent of the total fat content of frankfurters with a total fat content of 30% (control) was partially replaced by one of the vegetable oils to reduce the pork fat content by 10%. The moisture and ash content of low-fat frankfurters with vegetable oil and rice bran fiber were all higher than the control (P<0.05). Low-fat frankfurters had reduced-fat content, energy values, cholesterol and trans-fat levels, and increased pH, cooking yield and TBA values compared to the controls (P<0.05). Low-fat frankfurters with reduced-fat content plus rice bran fiber had sensory properties similar to control frankfurters containing pork fat. Crown Copyright 2009. Published by Elsevier Ltd. All rights reserved.

Effect of different cooking methods on minerals, vitamins and nutritional quality indices of kutum roach (Rutilus frisii kutum).

PubMed

Hosseini, Hedayat; Mahmoudzadeh, Maryam; Rezaei, Masoud; Mahmoudzadeh, Leila; Khaksar, Ramin; Khosroshahi, Nader Karimian; Babakhani, Aria

2014-04-01

In this study, the influence of four cooking methods (baking, boiling, microwaving and frying) was evaluated on the nutritional value of kutum roach. Proximate, fatty acid composition, vitamin and mineral contents and also nutritional quality indices (NQI) of kutum roach were investigated before and after cooking treatment. All treated samples showed increase in protein, ash and lipid contents and decrease in the content of total omega-3 fatty acids (n-3) in comparison to raw fish fillets (control group). Cooking methods had no significant effect on omega-6 fatty acids (n-6) except for frying that increased it. Nonetheless, all of the cooking methods reduced vitamin B1, A and D contents. Boiling significantly decreased mineral contents including Na, K, P and Zn. Considering the overall nutritional quality indices, vitamin and mineral contents, baking is the best cooking method among other applied methods. Copyright © 2013 Elsevier Ltd. All rights reserved.

Determination of the floral origin of some Romanian honeys on the basis of physical and biochemical properties

NASA Astrophysics Data System (ADS)

Cimpoiu, Claudia; Hosu, Anamaria; Miclaus, Vasile; Puscas, Anitta

The aim of this study was to determine the physical and biochemical properties of some Romanian honeys in order to discriminate between their floral origins. The evaluated properties were total phenolic content, total protein content, total free amino acids content, color intensity (ABS450), pH, ash content, antioxidant activity. Twenty-six commercial honeys from six types of flowers (acacia, sunflower, forest, polyfloral, lime and Sea Buckthorn) were investigated. All samples showed considerable variations with reference to their properties. The properties values were in the range of approved limits (according to EU legislation). The total phenolic, total protein and total free amino acids contents and color intensity varied considerably. Similarly, forest honey had the highest antioxidant activity while the lowest was found in acacia honey. Correlation between the floral origin of honeys and the physical and biochemical properties, respectively, was observed. Moreover, this study demonstrates remarkable variation in DPPH scavenging activity and content of total phenols in honey, depending on its botanic source.

In vitro effects of coal fly ashes: hydroxyl radical generation, iron release, and DNA damage and toxicity in rat lung epithelial cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

van Maanen, J.M.; Borm, P.J.; Knaapen, A

1999-12-15

The authors measured iron release, acellular generation of hydroxyl radicals, and oxidative DNA damage and cytotoxicity in rat lung epithelial (RLE) cells by different coal fly ashes (CFA) that contain both quartz and iron. Seven samples of CFA with different particle size and quartz content (up to 14.1%) were tested along with silica (alpha-quartz), ground coal, and coal mine dust (respirable) as positive control particles, and fine TiO{sub 2} (anatase) as a negative control. Five test samples were pulverized fuel ashes (PFA), two samples were coal gasification (SCG) ashes (quartz content {lt} 0.1%), and one sample was a ground coal.more » No marked differences between SCG and PFA fly ashes were observed, and toxicity did not correlate with physicochemical characteristics or effect parameters. Stable surface radicals were only detected in the reference particles silica and coal mine dust, but not in CFA. On the other hand, hydroxyl radical generation by all fly ashes was observed in the presence of hydrogen peroxide. Also a relationship between acellular hydroxyl radical generation and oxidative DNA damage in RLE cells by CFA was observed. The respirable ashes (MAT023, 38, and 41) showed an extensive level of hydroxyl radical generation in comparison to nonrespirable fly ashes and respirable references. This was related to the iron mobilization from these particles. Themechanisms by which CFA and the positive references (silica, coal mine dust) affect rat lung epithelial cells seem to be different, and the data suggest that quartz in CFA does not act the same as quartz in silica or coal mine dust. However, the results indicate an important role for size and iron release in generation and subsequent effects of reactive oxygen species caused by CFA.« less

Gravity Effects in Small-Scale Structural Modeling

DTIC Science & Technology

1988-12-01

attenuating material (Reference 23). The materials tested were cellular concrete with fly ash, expanded polystyrene concrete with fly ash, foamed...polyurethane, foamed sulfer and molded expanded polystyrene . The studies showed that with proper adjustments in the cement content, water-cement ratio and foam...Compression (Ou,c) 4000 100 Tension (Ou,t) 400 10 E/Quc 1000 1000 Ou,c/Ou,t 10 10 Further analysis of the properties of expanded polystyrene concrete with

Study of Natural Radioactivity in Coal Samples of Baganuur Coal Mine, Mongolia

NASA Astrophysics Data System (ADS)

Altangerel, M.; Norov, N.; Altangerel, D.

2009-03-01

Coal and soil samples from Baganuur Coal Mine (BCM) of Mongolia have been investigated. The activities of 226Ra, 232Th and 40K have been measured by gamma-ray spectrometry using shielded HPGe detector. Contents of natural radionuclide elements (U, Th and K) have been determined. Also the activities and contents of radionuclide of ashes were determined which generated in Thermal Power Plant ♯3 of Ulaanbaatar from coal supplied from BCM.

Physico-chemical and sensory properties of cookies made from blends of germinated pigeon pea, fermented sorghum, and cocoyam flours.

PubMed

Okpala, Laura; Okoli, Eric; Udensi, Emelem

2013-01-01

Cookies were produced from germinated pigeon pea, fermented sorghum, and cocoyam flour (CF) blends to determine their potentials in cookie manufacture. Ten flour formulations were produced and they were evaluated for their proximate and functional properties. Protein content ranged from 4.85% to 19.89% with 100% CF (100CF) having the least value, while 100% germinated pigeon pea flour (100GPF) had the highest value. Increase in levels of GPF to the flour blends resulted in increase in protein content of the blends. Cookies made with 100% fermented sorghum flour (100FSF) had the highest ash content of 2.73%, while cookies made with 100GPF had the least ash content. Energy values of the cookies ranged between 369.37 and 376.56 kcal/100 g, with cookie formulation 50%CF:50%FSF having the least value and cookies made with 16.7%CF:16.7%FSF:66.6GPF having the highest value. The control (cookies made with wheat) had the highest spread ratio of 24.13, while cookies made with 100FSF had the least spread ratio of 14.97. Cookies made with 100CF were the least fragile. Sensory ratings revealed that cookies containing up to 50% CF and above, compared favorably with those made with wheat flour.

Physico-chemical and sensory properties of cookies made from blends of germinated pigeon pea, fermented sorghum, and cocoyam flours

PubMed Central

Okpala, Laura; Okoli, Eric; Udensi, Emelem

2013-01-01

Cookies were produced from germinated pigeon pea, fermented sorghum, and cocoyam flour (CF) blends to determine their potentials in cookie manufacture. Ten flour formulations were produced and they were evaluated for their proximate and functional properties. Protein content ranged from 4.85% to 19.89% with 100% CF (100CF) having the least value, while 100% germinated pigeon pea flour (100GPF) had the highest value. Increase in levels of GPF to the flour blends resulted in increase in protein content of the blends. Cookies made with 100% fermented sorghum flour (100FSF) had the highest ash content of 2.73%, while cookies made with 100GPF had the least ash content. Energy values of the cookies ranged between 369.37 and 376.56 kcal/100 g, with cookie formulation 50%CF:50%FSF having the least value and cookies made with 16.7%CF:16.7%FSF:66.6GPF having the highest value. The control (cookies made with wheat) had the highest spread ratio of 24.13, while cookies made with 100FSF had the least spread ratio of 14.97. Cookies made with 100CF were the least fragile. Sensory ratings revealed that cookies containing up to 50% CF and above, compared favorably with those made with wheat flour. PMID:24804009

Improvement in the traditional processing method and nutritional quality of traditional extruded cassava-based snack (modified Ajogun).

PubMed

Obadina, Adewale O; Oyewole, Olusola B; Williams, Oluwasolabomi E

2013-07-01

This study was carried out to investigate and improve the traditional processing method and nutritional quality of the traditional cassava snack (Ajogun). Cassava root (Manihot esculenta Crantz L.) of TME 419 variety was processed into mash (40% moisture content). The cassava mash was mixed into different blends to produce fried traditional "Ajogun", fried and baked extrudates (modified Ajogun) as snacks. These products were analyzed to determine the proximate composition including carbohydrate, fat, protein, fiber, ash, and moisture contents and functional properties such as bulk density. The results obtained for the moisture, fat, protein, and ash contents showed significant difference (P < 0.05) between the control sample and the extrudates. However, there was no significant difference (P > 0.05) in the carbohydrate and fiber contents between the three samples. There was no significant difference (P > 0.05) in the bulk density of the snacks. Also, sensory evaluation was carried out on the cassava-based snacks using the 9-point hedonic scale to determine the degree of acceptability. Results obtained showed significant difference (P < 0.05) between the extrudates and control sample in terms of appearance, taste, flavor, color, aroma, texture, and overall acceptability. The highest acceptability level of the product was at 8.04 for the control sample (traditional Ajogun). This study has shown that "Ajogun", which is a lesser known cassava product, is rich in protein and fat.

Heavy Metal Contents and Physical Parameters of Aegiceras corniculatum, Brassica juncea, and Litchi chinensis Honeys from Bangladesh

PubMed Central

Sarker, Nandita; Chowdhury, Muhammed Alamgir Zaman; Fakhruddin, Abu Naieum Muhammad; Fardous, Zeenath; Moniruzzaman, Mohammed; Gan, Siew Hua

2015-01-01

The present study was undertaken to determine the heavy metal levels and the physicochemical parameters (pH, electrical conductivity (EC), and ash, moisture, and total sugar content) of honeys from Bangladesh. Three different floral honeys were investigated, namely, khalsi (Aegiceras corniculatum), mustard (Brassica juncea), and litchi (Litchi chinensis) honeys. The heavy metals in the honeys were determined by using a High Temperature Dry Oxidation method followed by Atomic Absorption Spectroscopy. The mean pH, EC, and ash, moisture, and total sugar contents of the investigated honeys were 3.6, 0.51 mS/cm, 0.18%, 18.83%, and 68.30%, respectively. Iron was the most abundant among all the investigated heavy metals, ranging from 13.51 to 15.44 mg/kg. The mean concentrations of Mn and Zn in the investigated honeys were 0.28 mg/kg and 2.99 mg/kg, respectively. Cd was below the detection limit, and lead was found in some honey samples, but their contents were below the recommended Maximum Acceptable Level. Cr was also found in all of the samples, but its concentration was within the limit. The physicochemical analysis of the honey samples yielded levels within the limits set by the international honey legislation, indicating that the honey samples were of good quality and had acceptable values for maturity, purity, and freshness. PMID:26618176

Heavy Metal Contents and Physical Parameters of Aegiceras corniculatum, Brassica juncea, and Litchi chinensis Honeys from Bangladesh.

PubMed

Sarker, Nandita; Chowdhury, Muhammed Alamgir Zaman; Fakhruddin, Abu Naieum Muhammad; Fardous, Zeenath; Moniruzzaman, Mohammed; Gan, Siew Hua

2015-01-01

The present study was undertaken to determine the heavy metal levels and the physicochemical parameters (pH, electrical conductivity (EC), and ash, moisture, and total sugar content) of honeys from Bangladesh. Three different floral honeys were investigated, namely, khalsi (Aegiceras corniculatum), mustard (Brassica juncea), and litchi (Litchi chinensis) honeys. The heavy metals in the honeys were determined by using a High Temperature Dry Oxidation method followed by Atomic Absorption Spectroscopy. The mean pH, EC, and ash, moisture, and total sugar contents of the investigated honeys were 3.6, 0.51 mS/cm, 0.18%, 18.83%, and 68.30%, respectively. Iron was the most abundant among all the investigated heavy metals, ranging from 13.51 to 15.44 mg/kg. The mean concentrations of Mn and Zn in the investigated honeys were 0.28 mg/kg and 2.99 mg/kg, respectively. Cd was below the detection limit, and lead was found in some honey samples, but their contents were below the recommended Maximum Acceptable Level. Cr was also found in all of the samples, but its concentration was within the limit. The physicochemical analysis of the honey samples yielded levels within the limits set by the international honey legislation, indicating that the honey samples were of good quality and had acceptable values for maturity, purity, and freshness.

Innovative biocatalytic production of soil substrate from green waste compost as a sustainable peat substitute.

PubMed

Kazamias, Georgios; Roulia, Maria; Kapsimali, Ioanna; Chassapis, Konstantinos

2017-12-01

In the present work, a new simple and quick eco-friendly method is discussed to handle effectively the green wastes and produce a sustainable peat substitute of high quality on the large scale. Principal physicochemical parameters, i.e., temperature, moisture, specific weight, pH, electrical conductivity and, also, microorganisms, organic matter, humic substances, total Kjeldahl nitrogen and total organic carbon, C/N ratio, ash, metal content and phytotoxicity, were monitored systematically. Humic substances content values were interrelated to both C/N ratio and pH values and, similarly, bulk density, TOC, TKN, C/N, GI, ash and organic matter were found interconnected to each other. A novel biocatalyst, extremely rich in soil microorganisms, prepared from compost extracts and peaty lignite, accelerated the biotransformation. Zeolite was also employed. The compost does not demonstrate any phytotoxicity throughout the entire biotransformation process and has increased humic substances content. Both humic substances content and germination index can be employed as maturation indices of the compost. Addition of compost, processed for 60 days only, in cultivations of grass plants led to a significant increase in the stem mass and root size, annotating the significant contribution of the compost to both growth and germination. The product obtained is comparable to peat humus, useful as peat substitute and can be classified as a first class soil conditioner suitable for organic farming. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preparation of Activated Carbon from Palm Shells Using KOH and ZnCl2 as the Activating Agent

NASA Astrophysics Data System (ADS)

Yuliusman; Nasruddin; Afdhol, M. K.; Amiliana, R. A.; Hanafi, A.

2017-07-01

Palm shell is a potential source of raw materials for the produce of activated carbon as biosorbent for quite large numbers. The purpose of this study is to produce activated carbon qualified Indonesian Industrial Standard (SNI), which will be used as biosorbent to purify the impurities in the off gas petroleum refinery products. Stages of manufacture of activated carbon include carbonization, activation of chemistry and physics. Carbonization of activated carbon is done at a temperature of 400°C followed by chemical activation with active agent KOH and ZnCl2. Then the physical activation is done by flowing N2 gas for 1 hour at 850°C and followed by gas flow through the CO2 for 1 hour at 850°C. Research results indicate that activation of the active agent KOH produce activated carbon is better than using the active agent ZnCl2. The use of KOH as an active agent to produce activated carbon with a water content of 13.6%, ash content of 9.4%, iodine number of 884 mg/g and a surface area of 1115 m2/g. While the use of ZnCl2 as the active agent to produce activated carbon with a water content of 14.5%, total ash content of 9.0%, iodine number 648 mg/g and a surface area of 743 m2/g.

Geology, coal resources, and chemical analyses of coal from the Fruitland Formation, Kimbeto EMRIA study site, San Juan County, New Mexico

USGS Publications Warehouse

Schneider, Gary B.; Hildebrand, Rick T.; Affolter, Ronald H.

1979-01-01

The Kimbeto EMRIA study site, an area of about 20 square miles (52 km2), is located on the south margin of the San Juan Basin on the gently northward-dipping strata of the Upper Cretaceous Fruitland Formation and the Kirtland Shale. The coal beds are mainly in the lower 150 feet (45 m) of the Fruitland Format ion. Coal resources--measured, indicated, and inferred--with less than 400 feet (120 m) of overburden in the site are 69,085,000 short tons (62,660,100 metric tons), 369,078,000 short tons (334,754,000 metric tons), and 177,803,000 short tons (161,267,000 metric tons) respectively. About 68 percent of these resources are overlain by 200 feet (60 m) or less of overburden. The apparent rank of the coal ranges from subbituminous B to subbituminous A. The average Btu/lb value of 14 core samples from the site on the as-received basis is 8,240 (4580 Kcal/kg), average ash content is 23.4 percent, and average sulfur content is 0.5 percent. Analyses of coal from the Kimbeto EMRIA study site show significantly higher ash content and significantly lower contents of volatile matter, fixed carbon, carbon, and a significantly lower heat of combustion when compared with other coal analyses from the Rocky Mountain province.

Experimental Study on Semi-Dry Flue Gas Desulfurization Ash Used in Steel Slag Composite Material

NASA Astrophysics Data System (ADS)

Lu, Lijun; Fang, Honghui

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 2% is optimal, where flexural strength is reduced by 10% 23% and compressive strength reduced by 5.7% 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 2%, the flexural strength is increased by 5 7% and the compressive strength is reduced by 1 2%. The results show that the formula two is better.

Effects of microbial phytase, produced by solid-state fermentation, on the performance and nutrient utilisation of broilers fed maize- and wheat-based diets.

PubMed

Wu, Y B; Ravindran, V; Hendriks, W H

2003-12-01

1. The influence of a microbial phytase on the performance, toe ash contents and nutrient utilisation of male broilers fed diets based on maize and wheat was investigated. The experiment was conducted as 2 x 2 x 2 factorial arrangement of treatments. Within the factorial, two diet types (maize-soy or wheat-soy) containing two levels of non-phytate phosphorus (3.0 or 4.5 g/kg) were evaluated and each level of non-phytate phosphorus was supplemented with 0 or 500 PU phytase/kg diet. Each of the 8 dietary treatments were fed to 6 pens of 8 birds from d 1 to 21 post-hatching. 2. Main effects of diet type and phytase were observed for all parameters. Main effect of non-phytate phosphorus was significant only for feed/gain and toe ash contents. Phytase addition improved weight gains irrespective of diet type or non-phytate phosphorus level, but the magnitude of improvement in the phosphorus-deficient wheat-soy diet was greater, resulting in a diet type x non-phytate phosphorus interaction. Responses in toe ash contents were noted only in phosphorus-deficient diets, as indicated by a non-phytate phosphorus x phytase interaction. 3. Phytase addition improved apparent metabolisable energy values of wheat-based diets, but had little effect on the apparent metabolisable energy of maize-based diets as shown by a diet type x phytase interaction. The apparent metabolisable energy was not influenced by dietary non-phytate P. 4. Phytase improved ileal nitrogen digestibility in both diet types, but the responses to added phytase tended to be higher in wheat-based diets, as shown by a diet type x phytase interaction. 5. Increasing the dietary non-phytate phosphorus level reduced phosphorus digestibility and increased excreta phosphorus content. Addition of phytase improved phosphorus digestibility, but the increments were higher in low phosphorus diets resulting in a non-phytate phosphorus x phytase interaction. Phytase addition tended to lower the excreta phosphorus content, but the effects were greater in birds fed low phosphorus diets, as shown by a non-phytate phosphorus x phytase interaction.

The Effects of Different Substrates on the Growth, Yield, and Nutritional Composition of Two Oyster Mushrooms (Pleurotus ostreatus and Pleurotus cystidiosus).

PubMed

Hoa, Ha Thi; Wang, Chun-Li; Wang, Chong-Ho

2015-12-01

The study was conducted to compare the effects of different agro-wastes on the growth, yield, and nutritional composition of oyster mushrooms Pleurotus ostreatus (PO) and Pleurotus cystidiosus (PC). Seven substrate formulas including sawdust (SD), corncob (CC), sugarcane bagasse (SB) alone and in combination of 80 : 20, 50 : 50 ratio between SD and CC, SD and SB were investigated. The results indicated that different substrate formulas gave a significant difference in total colonization period, characteristics of fruiting bodies, yield, biological efficiency (BE), nutritional composition and mineral contents of two oyster mushrooms PO and PC. The results showed that increasing CC and SB reduced C/N ratio, and enhanced some mineral contents (Ca, P, and Mg) of substrate formulas. The increased amount of CC and SB of substrate formulas enhanced protein, ash, mineral contents (Ca, K, Mg, Mn, and Zn) of fruiting bodies of both mushrooms. Substrates with 100% CC and 100% SB were the most suitable substrate formulas for cultivation of oyster mushrooms PO and PC in which they gave the highest values of cap diameter, stipe thickness, mushroom weight, yield, BE, protein, fiber, ash, mineral content (Ca, K, and Mg) and short stipe length. However, substrate formula 100% CC gave the slowest time for the first harvest of both mushrooms PO and PC (46.02 days and 64.24 days, respectively). It is also found that the C/N ratio of substrate formulas has close correlation with total colonization period, mushroom weight, yield, BE and protein content of mushroom PO and PC.

The Effects of Different Substrates on the Growth, Yield, and Nutritional Composition of Two Oyster Mushrooms (Pleurotus ostreatus and Pleurotus cystidiosus)

PubMed Central

Hoa, Ha Thi; Wang, Chong-Ho

2015-01-01

The study was conducted to compare the effects of different agro-wastes on the growth, yield, and nutritional composition of oyster mushrooms Pleurotus ostreatus (PO) and Pleurotus cystidiosus (PC). Seven substrate formulas including sawdust (SD), corncob (CC), sugarcane bagasse (SB) alone and in combination of 80 : 20, 50 : 50 ratio between SD and CC, SD and SB were investigated. The results indicated that different substrate formulas gave a significant difference in total colonization period, characteristics of fruiting bodies, yield, biological efficiency (BE), nutritional composition and mineral contents of two oyster mushrooms PO and PC. The results showed that increasing CC and SB reduced C/N ratio, and enhanced some mineral contents (Ca, P, and Mg) of substrate formulas. The increased amount of CC and SB of substrate formulas enhanced protein, ash, mineral contents (Ca, K, Mg, Mn, and Zn) of fruiting bodies of both mushrooms. Substrates with 100% CC and 100% SB were the most suitable substrate formulas for cultivation of oyster mushrooms PO and PC in which they gave the highest values of cap diameter, stipe thickness, mushroom weight, yield, BE, protein, fiber, ash, mineral content (Ca, K, and Mg) and short stipe length. However, substrate formula 100% CC gave the slowest time for the first harvest of both mushrooms PO and PC (46.02 days and 64.24 days, respectively). It is also found that the C/N ratio of substrate formulas has close correlation with total colonization period, mushroom weight, yield, BE and protein content of mushroom PO and PC. PMID:26839502

Ash after forest fires. Effects on soil hydrology and erosion

NASA Astrophysics Data System (ADS)

Bodí, Merche B.

2013-04-01

Hillslopes were though to be most susceptible to enhanced hydro-geomorphological responses immediately following burning, with susceptibility declining during the first months or years depending on the soil and vegetation recovery. However, Cerdà (1998) found some indices in that immediately after the fire, the thin wettable ash layer that typically covers the ground could absorb rainfall and prevent or delay the onset of overland flow and associated erosion. Therefore the time lag while ash remains on the ground become of crucial importance to protect the soil after a wildfire. The effect of this ash layer was rarely been considered in detail because ash has often been reduced or redistributed by wind or water erosion before the onset of monitoring and thus the data collection typically begun some weeks or month after the fire. The first papers focussed only on ash and its hydrological effects were published by Cerdà and Doerr (2008) and by Woods and Balfour (2008). The results showed that the soil covered with ash indeed reduced and delayed surface runoff, reduced soil splash detachment and produced lower sediment yield compared to bare terrain. However, these findings arose more questions, as for instance: Why in other research there were indices that ash reduces infiltration? what is the mechanism by which why ash reduces overland flow? The research went further with Bodí PhD. First of all, it was crucial the agreement on the fact that the material "ash" is very variable depending on the original vegetation and the type and temperature of combustion. Therefore ash properties are different between wildfires even and within a fire. This is the main reason of its different effects and thus ash not always reduces runoff and sediment yield. In this way, depending on the nature of ash, it can increase overland flow if it is crusted (usually it contains a high content of calcium carbonate), it is water repellent (with high contents of organic carbon and specially from certain Eucaliptus and Pinus), or if clog soil pores (depending also on the soil type). If ash is wettable, it can store even 80% of its volume and then it will delay and reduce overland flow proportionally to the thickness of the ash layer. Once ash gets saturated, the flow tends to adjust to an infiltration rate similar to the soil itself, or sometimes higher due to the protection of ash that can reduce soil water repellency and soil sealing (Bodí et al. 2011, 2012). Still, many other aspects on ash remain unknown and ash present us more questions like, what it is its role on the carbon cycle? what is the extent of the ahs effects at basin scale? what is the fate of ash and how long it remains in the ecosystem? are there specific effects of ash depending on the ecosystem and so the type of ash? Acknowledgements This work was supported financially by a research fellowship (AP2007-04602) from the Spanish Ministry of Science and Innovation (M.B. Bodí) and the projects PT2009-0073 and CGL2010-21670-C02-01. References Bodí, M.B., Mataix-Solera, J., Doerr, S.H., Cerdà, A., 2011, The wettability of ash from burned vegetation and its relationship to Mediterranean plant species type, burn severity and total organic carbon content. Geoderma 160, 599-607. Bodí, M.B., Doerr, S.H., Cerdà, A., Mataix-Solera, J., 2012, Hydrological effects of a layer of vegetation ash on underlying wettable and water repellent soil. Geoderma 191, 14-23 Cerdà, A., 1998, Changes in overland flow and infiltration after a rangeland fire in a Mediterranean scrubland. Hydrological Processes 12, 1031-1042. Cerdà, A., Doerr, S.H., 2008, The effect of ash and needle cover on surface runoff and erosion in the immediate post-fire period. Catena 74, 256-263. Woods, S.W., Balfour, V., 2008, The effect of ash on runoff and erosion after a forest wildfire, Montana, U.S.A. International Journal of Wildland Fire 17, 535-548.

Mineral content prediction for unconventional oil and gas reservoirs based on logging data

NASA Astrophysics Data System (ADS)

Maojin, Tan; Youlong, Zou; Guoyue

2012-09-01

Coal bed methane and shale oil &gas are both important unconventional oil and gas resources, whose reservoirs are typical non-linear with complex and various mineral components, and the logging data interpretation model are difficult to establish for calculate the mineral contents, and the empirical formula cannot be constructed due to various mineral. The radial basis function (RBF) network analysis is a new method developed in recent years; the technique can generate smooth continuous function of several variables to approximate the unknown forward model. Firstly, the basic principles of the RBF is discussed including net construct and base function, and the network training is given in detail the adjacent clustering algorithm specific process. Multi-mineral content for coal bed methane and shale oil &gas, using the RBF interpolation method to achieve a number of well logging data to predict the mineral component contents; then, for coal-bed methane reservoir parameters prediction, the RBF method is used to realized some mineral contents calculation such as ash, volatile matter, carbon content, which achieves a mapping from various logging data to multimineral. To shale gas reservoirs, the RBF method can be used to predict the clay content, quartz content, feldspar content, carbonate content and pyrite content. Various tests in coalbed and gas shale show the method is effective and applicable for mineral component contents prediction

Block coals from Indiana: Inferences on changing depositional environment

USGS Publications Warehouse

Mastalerz, Maria; Padgett, P.L.; Eble, C.F.

2000-01-01

Significant differences in coal petrography, palynology and coal quality were found between the Lower Block and Upper Block Coal Members (Brazil Formation, Pennsylvanian) in Daviess County, Indiana. The Lower Block Coal Member ranges in thickness from 51 to 74 cm and the Upper Block Coal Member ranges from 20 to 65 cm. Average sulfur content and ash yield of the Lower Block coal (0.98%, 7.65%) are lower than in the Upper Block coal. Megascopically, the coals show distinct differences. The Lower Block is a banded coal with numerous thin fusain horizons and a thin clay parting in the lower third of the seam. The Upper Block coal has a dulling-upward trend, with a bright clarain found at the base that grades into a clarain and then into a durain in the upper portion of the seam. Vitrinite content of the Lower Block coal ranges from 63% to 78%, with the highest vitrinite content found in the middle portion of the seam. In the Upper Block coal, vitrinite content ranges from 40% to 83%, with the highest values found in the lower part of the seam. Ash yield is higher in the upper part of the Upper Block coal, reaching up to 40%. The Lower Block coal is dominated by lycopod trees and tree ferns. The Upper Block coal shows marked differences in spore assemblages between lower and upper parts of the seam. The lower half is dominated by large lycopod trees and tree ferns, similar to the Lower Block coal. The upper half is dominated by small lycopods, mainly Densosporites and Radiizonates. These differences between the Lower Block and Upper Block Coal Members are significant correlation tools applicable to mining exploration and chronostratigraphy. (C) 2000 Elsevier Science B.V. All rights reserved.Significant differences in coal petrography, palynology and coal quality were found between the Lower Block and Upper Block Coal Members (Brazil Formation, Pennsylvanian) in Daviess County, Indiana. The Lower Block Coal Member ranges in thickness from 51 to 74 cm and the Upper Block Coal Member ranges from 20 to 65 cm. Average sulfur content and ash yield of the Lower Block coal (0.98%, 7.65%) are lower than in the Upper Block coal. Megascopically, the coals show distinct differences. The Lower Block is a banded coal with numerous thin fusain horizons and a thin clay parting in the lower third of the seam. The Upper Block coal has a dulling-upward trend, with a bright clarain found at the base that grades into a clarain and then into a durain in the upper portion of the seam. Vitrinite content of the Lower Block coal ranges from 63% to 78%, with the highest vitrinite content found in the middle portion of the seam. In the Upper Block coal, vitrinite content ranges from 40% to 83%, with the highest values found in the lower part of the seam. Ash yield is higher in the upper part of the Upper Block coal, reaching up to 40%. The Lower Block coal is dominated by lycopod trees and tree ferns. The Upper Block coal shows marked differences in spore assemblages between lower and upper parts of the seam. The lower half is dominated by large lycopod trees and tree ferns, similar to the Lower Block coal. The upper half is dominated by small lycopods, mainly Densosporites and Radiizonates. These differences between the Lower Block and Upper Block Coal members are significant correlation tools applicable to mining exploration and chronostratigraphy.

[Correlation of Persistent Free Radicals, PCDD/Fs and Metals in Waste Incineration Fly Ash].

PubMed

Wang, Tian-jiao; Chen, Tong; Zhan, Ming-xiu; Guo, Ying; Li, Xiao-dong

2016-03-15

Environmentally persistent free radicals (EPFRs) are relatively highly stable and found in the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Recent studies have concentrated on model dioxin formation reactions and there are few studies on actual waste incineration fly ash. In order to study EPFRs and the correlation with dioxins and heavy metals in waste incineration fly ash, the spins of EPFRs, concentration of PCDD/Fs and metals in samples from 6 different waste incinerators were detected. The medical waste incineration fly ash from Tianjin, municipal solid waste incineration fly ash from Jiangxi Province, black carbon and slag from municipal solid waste incinerator in Lanxi, Zhejiang Province, all contained EPFRs. Above all the signal in Tianjin sample was the strongest. Hydroxyl radicals, carbon-center radicals and semiquinone radicals were detected. Compared with other samples, Jiangxi fly ash had the highest toxic equivalent quantity (TEQ) of dioxins, up to 7.229 4 ng · g⁻¹. However, the dioxin concentration in the Tianjin sample containing the strongest EPFR signals was only 0.092 8 ng · g⁻¹. There was perhaps little direct numeric link between EPFRs and PCDD/Fs. But the spins of EPFRs in samples presented an increasing trend as the metal contents increased, especially with Al, Fe, Zn. The signal strength of radicals was purposed to be related to the metal contents. The concentration of Zn (0.813 7% ) in the Tianjin sample was the highest and this sample contained much more spins of oxygen-center radicals. We could presume the metal Zn had a greater effect on the formation of EPFRs, and was easier to induce the formation of radicals with a longer half-life period.

Study of the activity of the local adding [ash from palm plantation wastes

NASA Astrophysics Data System (ADS)

Rezig, D.; Bentabba, M. T.

2018-05-01

The objectify of this work is to study the activity of the ash by substitution of 25℅ cement of mineral powder ash from palm plantation wastes, and its influences mechanical performances on mortar. Such as the resistance of the compression, the traction, and durability by reducing calcium hydroxide content Ca[OH]2 generated by chemical reaction of cement, which has a harmful effect in durability. The activity of this waste was evaluated in the utilized of mechanic attempts resistance of the compression and flexion in 28 day] was also studied, the obtained results shows the best result of the index of ash activity is i=0,69 was obtained in mixing cement with CRS.

Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seggiani, Maurizia, E-mail: m.seggiani@diccism.unipi.it; Puccini, Monica, E-mail: m.puccini@diccism.unipi.it; Raggio, Giovanni, E-mail: g.raggio@tiscali.it

2012-10-15

Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effectmore » of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was within the limits for landfilling inert residues. On the other hand, sulfate and chloride releases were found to comply with the limits for non-hazardous residues.« less

Volcanic ash in the water column: Physiological impact on the suspension-feeding bivalve Mytilus chilensis.

PubMed

Salas-Yanquin, L P; Navarro, J M; Pechenik, J A; Montory, J A; Chaparro, O R

2018-02-01

Ashes settling into the sea from volcanic explosions expose suspension-feeding species to reduced seston quality. Adults and juveniles of the mussel Mytilus chilensis were exposed for 15days to the phytoplankton Isochrysis galbana together with various concentrations of ashes. We then quantified impact on survival and physiology. Although no individuals died during the experiment, by the end of the study clearance rates and oxygen consumption rates had decreased substantially, and tissue weight of mussels exposed to the highest ash concentrations declined substantially. Gills showed no physical damage, but did show abundant mucus secretion in response to ash particles. Moreover, as the relative proportions of microalgae to ash in the diet decreased, individuals showed increasing preferential ingestion of microalgal particles. Increased ash content in the diet altered physiological rates and activated distinct particle selection with a high production of pseudofeces and high energy costs, with potential long-term consequences. Copyright © 2017 Elsevier Ltd. All rights reserved.

Moist caustic leaching of coal

DOEpatents

Nowak, Michael A.

1994-01-01

A process for reducing the sulfur and ash content of coal. Particulate coal is introduced into a closed heated reaction chamber having an inert atmosphere to which is added 50 mole percent NaOH and 50 mole percent KOH moist caustic having a water content in the range of from about 15% by weight to about 35% by weight and in a caustic to coal weight ratio of about 5 to 1. The coal and moist caustic are kept at a temperature of about 300.degree. C. Then, water is added to the coal and caustic mixture to form an aqueous slurry, which is washed with water to remove caustic from the coal and to produce an aqueous caustic solution. Water is evaporated from the aqueous caustic solution until the water is in the range of from about 15% by weight to about 35% by weight and is reintroduced to the closed reaction chamber. Sufficient acid is added to the washed coal slurry to neutralize any remaining caustic present on the coal, which is thereafter dried to produce desulfurized coal having not less than about 90% by weight of the sulfur present in the coal feed removed and having an ash content of less than about 2% by weight.

Catalyzed pyrolysis of grape and olive bagasse. Influence of catalyst type and chemical treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Encinar, J.M.; Beltran, F.J.; Ramiro, A.

1997-10-01

Catalyzed pyrolysis of grape and olive bagasse under different experimental conditions has been studied. Variables investigated were temperature and type and concentration of catalysts. Experiments were carried out in an isothermal manner. Products of pyrolysis are gases (H{sub 2}, CO, CO{sub 2}, and CH{sub 4}), liquids (methanol, acetone, furfurylic alcohol, phenol, furfural, naphthalene, and o-cresol), and solids (chars). Temperature is a significant variable, yielding increases of fixed carbon content, gases, and to a lesser extent, ash percentage. Catalyst presence also yields increases of solid phase content, but the amount of liquid components decrease. Among catalysts applied those of Fe andmore » Zn are the most advisable to obtain gases. Chemical treatment of bagasses with sulfuric or phosphoric acid washing leads to lower char yields, although fixed carbon content is higher and ash presence diminishes with respect to catalyst pyrolysis without chemical pretreatment. A pyrolysis kinetic study based on gas generation from thermal decomposition of residues has been carried out. From the model proposed, rate constants for the formation of each gas, reaction order of the catalyst, and activation energies were determined.« less

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

NASA Astrophysics Data System (ADS)

Samah, K. A.; Sahar, M. R.; Yusop, M.; Omar, M. F.

2018-03-01

Novel ceramics from waste material made of ( x) paper ash-(80 - x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO3), along with minor phases of γ-dicalcium silicate (Ca2SiO4) and quartz (SiO2). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.

[Rapid determination of componential contents and calorific value of selected agricultural biomass feedstocks using spectroscopic technology].

PubMed

Sheng, Kui-Chuan; Shen, Ying-Ying; Yang, Hai-Qing; Wang, Wen-Jin; Luo, Wei-Qiang

2012-10-01

Rapid determination of biomass feedstock properties is of value for the production of biomass densification briquetting fuel with high quality. In the present study, visible and near-infrared (Vis-NIR) spectroscopy was employed to build prediction models of componential contents, i. e. moisture, ash, volatile matter and fixed-carbon, and calorific value of three selected species of agricultural biomass feedstock, i. e. pine wood, cedar wood, and cotton stalk. The partial least squares (PLS) cross validation results showed that compared with original reflection spectra, PLS regression models developed for first derivative spectra produced higher prediction accuracy with coefficients of determination (R2) of 0.97, 0.94 and 0.90, and residual prediction deviation (RPD) of 6.57, 4.00 and 3.01 for ash, volatile matter and moisture, respectively. Good prediction accuracy was achieved with R2 of 0.85 and RPD of 2.55 for fixed carbon, and R2 of 0.87 and RPD of 2.73 for calorific value. It is concluded that the Vis-NIR spectroscopy is promising as an alternative of traditional proximate analysis for rapid determination of componential contents and calorific value of agricultural biomass feedstock

The effect of irradiation in the preservation of pink pepper (Schinus terebinthifolius Raddi)

NASA Astrophysics Data System (ADS)

de Souza, Adriana Régia Marques; Arthur, Valter; Nogueira, Danielle Pires

2012-08-01

Pink peppers, also known as "pimenta-rosa" and "poivre rose", are the fruit of Schinus terebinthifolius Raddi, a species of pepper cultivated in Brazil, and have great potential for the exploration of uses. In efforts to lengthen the shelf life of this pepper, the purpose of this study was to evaluate the effect of different doses of radiation on its physical composition and color. The pink pepper samples were irradiated with doses of 0, 0.2, 0.4, 0.8 and 1.6 kGy, and the moisture, ash and lipid contents, pH and color were analyzed. The moisture content, lipid content and pH analysis indicated effects due to the irradiation (p>0.05) in which the higher doses resulted in decreases in the attribute. In contrast, there were no significant differences for the ash analysis (p<0.05) among the studied doses. The color of the pink peppers were affected by the irradiation: the parameters a* and b* were the most affected by the intermediate doses (0.2 and 0.8 kGy), which induced their elevation, enhancing the reddish and yellowish colors. Based on the presented data, irradiation is as an alternative preservation process for pink peppers.

Fly ash carbon passivation

DOE Office of Scientific and Technical Information (OSTI.GOV)

La Count, Robert B; Baltrus, John P; Kern, Douglas G

A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most ofmore » the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.« less

Active mineral additives of sapropel ashes

NASA Astrophysics Data System (ADS)

Khomich, V. A.; Danilina, E. V.; Krivonos, O. I.; Plaksin, G. V.

2015-01-01

The goal of the presented research is to establish a scientific rational for the possibility of sapropel ashes usage as an active mineral additive. The research included the study of producing active mineral additives from sapropels by their thermal treatment at 850900 °C and afterpowdering, the investigation of the properties of paste matrix with an ash additive, and the study of the ash influence on the cement bonding agent. Thermogravimetric analysis and X-ray investigations allowed us to establish that while burning, organic substances are removed, clay minerals are dehydrated and their structure is broken. Sapropel ashes chemical composition was determined. An amorphous ash constituent is mainly formed from silica of the mineral sapropel part and alumosilicagels resulted from clay minerals decomposition. Properties of PC 400 and PC 500A0 sparopel ash additives were studied. Adding ashes containing Glenium plasticizer to the cement increases paste matrix strength and considerably reduces its water absorption. X-ray phase analysis data shows changes in the phase composition of the paste matrix with an ash additive. Ash additives produce a pozzolanic effect on the cement bonding agent. Besides, an ash additive due to the alumosilicagels content causes transformation from unstable calcium aluminate forms to the stable ones.

Sensory, Physico-Chemical and Water Sorption Properties of Corn Extrudates Enriched with Spirulina.

PubMed

Tańska, Małgorzata; Konopka, Iwona; Ruszkowska, Millena

2017-09-01

This study compares the quality of extrudates made from corn grits with the addition of up to 8% of spirulina powder. The sensory properties (shape, color, aroma, taste and crispness), chemicals (content of water, protein, fat, ash, fiber, carbohydrates, carotenoids, chlorophyll and phycocyanin) and physical properties (color, water absorption index, expansion indices, texture and water sorption properties) were determined. It has been found that spirulina-enriched extrudates had slightly lower sensory scores, but the addition of spirulina improved their nutritional value. The contents of protein, ash, fiber and β-carotene increased in extrudates with 8% of spirulina by 34, 36, 140 and 1,260%, respectively. The increasing addition of spirulina caused a decrease in extrudates lightness, an increase in their greenness and yellowness accompanied by a decrease of expansion indices and an increase of softness. Only small differences were found in water sorption properties, suggesting a similar behavior of spirulina-enriched extrudates during storage.

Protein and starch digestibilities and mineral availability of products developed from potato, soy and corn flour.

PubMed

Gahlawat, P; Sehgal, S

1998-01-01

A technique for development of potato flour was standardized. Five products viz. cake, biscuit, weaning food, panjiri and ladoo were prepared incorporating potato flour, defatted soy flour and corn flour. Baking and roasting were the major processing techniques employed for the development of these products. Protein, ash and fat contents of potato flour were almost similar to those of raw potatoes. Significant differences in protein, ash and fat contents of all the products were observed. Protein and starch digestibility of potato flour was significantly higher than that of raw potatoes. Protein digestibility increased by 12 to 17 percent on baking or roasting of products. Processed products had significantly higher starch digestibility and mineral availability compared to raw products. Thus, it can be concluded that roasting and baking are effective means of improving starch and protein digestibility and mineral availability of products.

Upgrading of consumer characteristics of granulated solid fuel from mixture of low-grade coal and biomass

NASA Astrophysics Data System (ADS)

Kuzmina, J. S.; Milovanov, O. Yu; Sinelshchikov, V. A.; Sytchev, G. A.; Zaichenko, V. M.

2015-11-01

Effect of torrefaction on consumer characteristics of fuel pellets made of low-grade and agricultural waste is shown. Data on the volatile content, ash content, calorific value and hygroscopicity for initial pellets and pellets, heat-treated at various temperatures are presented. The experimental study of the combustion process of initial and heat-treated pellets showed that torrefaction of pellets leads to a decreasing of the ignition temperature and an increasing of the efficiency of boiler plant.

Enrichment and oral bioaccessibility of selected trace elements in fly ash-derived magnetic components.

PubMed

Bourliva, Anna; Papadopoulou, Lambrini; Aidona, Elina; Simeonidis, Konstantinos; Vourlias, George; Devlin, Eamonn; Sanakis, Yiannis

2017-01-01

The mineralogy, morphology, and chemical composition of magnetic fractions separated from fly ashes (FAs) originating from Greek lignite-burning power plants was investigated. The oral bioaccessibility of potentially harmful elements (PHEs) from the fly ash magnetic fractions (FAMFs) was also assessed using in vitro gastrointestinal extraction (BARGE Unified Bioaccessibility Method, UBM). The FAMFs isolated were in the range 4.6-18.4%, and their mass specific magnetic susceptibility ranged from 1138 × 10 -8 to 1682 × 10 -8  m 3 /kg. XRD analysis and Mossbauer spectroscopy indicated that the dominant iron species were Fe-rich aluminosilicate glass along with magnetite, hematite, and maghemite (in decreasing order). The raw FAs exhibited differences in their chemical composition, indicating the particularity of every lignite basin. The elemental contents of FAMFs presented trends with fly ash type; thus, the FAMFs of high-Ca FAs were enriched in siderophile (Cr, Co, Ni) and lithophile (Cs, Li, Rb) elements and those separated from low-Ca FAs were presented depleted in chalcophile elements. Based on UBM extraction tests, the PHEs were more bioaccessible from the non-magnetic components of the FAs compared to the magnetic ones; however, the bioaccessible fractions estimated for the FAMFs were exceeding 40 % in many cases. Arsenic was found to be significantly bioaccessible (median ~ 80 %) from FAMFs despite the lower As contents in the magnetic fraction.

Remediation of AMD using industrial waste adsorbents

NASA Astrophysics Data System (ADS)

Mohammed, Nuur Hani Bte; Yaacob, Wan Zuhairi Wan

2016-11-01

The study investigates the characteristic of industrial waste as adsorbents and its potential as heavy metals absorbents in AMD samples. The AMD sample was collected from active mine pond and the pH was measured in situ. The metal contents were analyzed by ICP-MS. The AMD water was very acidic (pH< 3.5), and the average heavy metals content in AMD were high especially in Fe (822.029 mg/l). Fly ash was found to be the most effective absorbent material containing high percentage of CaO (57.24%) and SiO2 (13.88%), followed by ladle furnace slag containing of high amount of CaO (51.52%) and Al2O3 (21.23%), while biomass ash consists of SiO2 (43.07%) and CaO (12.97%). Tank analysis display a huge changes due to pH value change from acidity to nearly neutral phases. After 50 days, fly ash remediation successfully increase the AMD pH values from pH 2.57-7.09, while slag change from acidity to nearly alkaline phase from pH 2.60-7.3 and biomass has change to pH 2.54-6.8. Fly ash has successfully remove Fe, Mn, Cu, and Ni. Meanwhile, slag sample displays as an effective adsorbent to adsorb more Pb and Cd in acid mine drainage.

Preparation and characterization of a hybrid alkaline binder based on a fly ash with no commercial value

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mejia, Johanna M.; Rodriguez, Erich; Mejia de Gutierrez, Ruby

2015-05-18

Alkali-activated Portland fly ash cement (FA/OPC) and alkali activated blast furnace slag-fly ash cement (FA/GBFS) were prepared using 70% of a low quality fly ash (FA). The low quality is associated with a high content of unburned material (loss of ignition of 14.6%). The hybrid cements were activated by the alkaline solution in order to obtain an overall SiO 2/Al 2O 3 molar ratio of 5.0 and 6.0 and unique overall Na 2O/SiO 2 molar ratio of 0.21. The microstructural characterization of the blended pastes generated in the systems showed the coexistence of amorphous gels C-A-S-H and N-A-S-H gels inmore » the hybrid systems. The addition of OPC or GBFS increases the compressive strength (at 28 days of curing) up to 127% compared with the geopolymer systems based only on FA used in this study. The content of silicates soluble also plays an important role in the reaction products and higher SiO 2/Al 2O 3 lead to obtain higher mechanical performance and denser structure. The results obtained show that these hybrid cements are an effective way for valorization the waste used in this study for the production of high strength and low-carbon footprint cement-type material.« less

Fly ashes from coal and petroleum coke combustion: current and innovative potential applications.

PubMed

González, Aixa; Navia, Rodrigo; Moreno, Natalia

2009-12-01

Coal fly ashes (CFA) are generated in large amounts worldwide. Current combustion technologies allow the burning of fuels with high sulfur content such as petroleum coke, generating non-CFA, such as petroleum coke fly ash (PCFA), mainly from fluidized bed combustion processes. The disposal of CFA and PCFA fly ashes can have severe impacts in the environment such as a potential groundwater contamination by the leaching of heavy metals and/or particulate matter emissions; making it necessary to treat or reuse them. At present CFA are utilized in several applications fields such as cement and concrete production, agriculture and soil stabilization. However, their reuse is restricted by the quality parameters of the end-product or requirements defined by the production process. Therefore, secondary material markets can use a limited amount of CFA, which implies the necessity of new markets for the unused CFA. Some potential future utilization options reviewed herein are zeolite synthesis and valuable metals extraction. In comparison to CFA, PCFA are characterized by a high Ca content, suggesting a possible use as neutralizers of acid wastewaters from mining operations, opening a new potential application area for PCFA that could solve contamination problems in emergent and mining countries such as Chile. However, this potential application may be limited by PCFA heavy metals leaching, mainly V and Ni, which are present in PCFA in high concentrations.

Characterization the potential of biochar from cow and pig manure for geoecology application

NASA Astrophysics Data System (ADS)

Gunamantha, I. M.; Widana, G. A. B.

2018-03-01

Biochar is a solid product generated from the carbonization of biomass with various potential benefits. The utilisation of biochar should be adapted to its characteristic which is mainly influenced by its feedstock. In this study, cow and pig manure biochar generated by a conventional process, were characterized by its physical and chemical analysis and its potential to be used as soil amendment. For this purpose, several main parameters were analyzed: organic carbon, Nutrient (total-N, available P and K) status, Cation Exchange Capacity (CEC), proximate data analysis (moisture content, ash, volatile matter and fixed carbon) and its ash composition. The comparison between biochar and feedstock will be based on these parameters. The results of this study show that the organic carbon, available P, ash, and fixed carbon content of pig-manure biochar is higher than cow manure-derived biochar; while total-N, available K, CEC and volatile matter is lower. On its ash composition, the pig manure-derived biochar is dominated by SiO2, Al2O3, Fe2O3, P2O5, and CaO while the cow manure-derived biochar is dominated by SiO2, CaO, Al2O3, K2O, and P2O5. However, both biochar show potential for improving soil quality and reducing carbon emission from animal manure.

Proximate composition and caloric content of eight Lake Michigan fishes

USGS Publications Warehouse

Rottiers, Donald V.; Tucker, Robert M.

1982-01-01

We measured the proximate composition (percentage lipid, water, fat-free dry material, ash) and caloric content of eight species of Lake Michigan fish: lake trout (Salvelinus namaycush), coho salmon (Oncorhynchus kisutch), lake whitefish (Coregonus clupeaformis), bloater (Coregonus hoyi), alewife (Alosa pseudoharengus), rainbow smelt (Osmerus mordax), deepwater sculpin (Myoxocephalus quadricornis), and slimy sculpin (Cottus cognatus). Except for alewives, proximate composition and caloric content did not differ significantly between males and females. And, for coho salmon, there was no significant difference in composition between fish collected in different years. Lipid and caloric content of lake trout increased directly with age. In all species examined, lipids and caloric contents were significantly lower in small, presumably immature, fish than in larger, older fish. Lipid content of lake trout, lake whitefish, and bloaters (range of means, 16-22%) was nearly 3 times higher than that of coho salmon, sculpins, rainbow smelt, and alewives (range of means, 5.2-7.0%). The mean caloric content ranged from 6.9 to 7.1 kcal/g for species high in lipids and from 5.8 to 6.3 kcal/g for species low in lipids. Although the caloric content of all species varied directly with lipid content and inversely with water content, an increase in lipid content did not always coincide with a proportional increase in caloric content when other components of fish composition were essentially unchanged. This observation suggests that the energy content of fish estimated from the proximate composition by using universal conversion factors may not necessarily be accurate.

Solid residues from Italian municipal solid waste incinerators: A source for "critical" raw materials.

PubMed

Funari, Valerio; Braga, Roberto; Bokhari, Syed Nadeem Hussain; Dinelli, Enrico; Meisel, Thomas

2015-11-01

The incineration of municipal solid wastes is an important part of the waste management system along with recycling and waste disposal, and the solid residues produced after the thermal process have received attention for environmental concerns and the recovery of valuable metals. This study focuses on the Critical Raw Materials (CRM) content in solid residues from two Italian municipal waste incinerator (MSWI) plants. We sampled untreated bottom ash and fly ash residues, i.e. the two main outputs of common grate-furnace incinerators, and determined their total elemental composition with sensitive analytical techniques such as XRF and ICP-MS. After the removal of a few coarse metallic objects from bottom ashes, the corresponding ICP solutions were obtained using strong digestion methods, to ensure the dissolution of the most refractory components that could host significant amounts of precious metals and CRM. The integration of accurate chemical data with a substance flow analysis, which takes into account the mass balance and uncertainties assessment, indicates that bottom and fly ashes can be considered as a low concentration stream of precious and high-tech metals. The magnesium, copper, antimony and zinc contents are close to the corresponding values of a low-grade ore. The distribution of the elements flow between bottom and fly ash, and within different grain size fractions of bottom ash, is appraised. Most elements are enriched in the bottom ash flow, especially in the fine grained fractions. However, the calculated transfer coefficients indicate that Sb and Zn strongly partition into the fly ashes. The comparison with available studies indicates that the CRM concentrations in the untreated solid residues are comparable with those residues that undergo post-treatment beneficiations, e.g. separation between ferrous and non-ferrous fractions. The suggested separate collection of "fresh" bottom ash, which could be processed for further mineral upgrading, can constitute an attractive option of the waste management system, when physical-mechanical devices are not available or could not be implemented in old MSWI systems. The suggested procedure may lead to the improvement of recovery efficiency up to 83% for CRM and 94% for other valuable metals. Copyright © 2014 Elsevier Ltd. All rights reserved.

Perspective usage estimation of Volga region combustible shale as a power generating fuel alternative

NASA Astrophysics Data System (ADS)

Korolev, E.; Barieva, E.; Eskin, A.

2018-05-01

A comprehensive study of combustible shale, common within Tatarstan and Ulyanovsk region, is carried out. The rocks physicochemical parameters are found to meet the power generating fuels requirements. The predictive estimate of ash products properties of combustible shale burning is held. Minding furnace process technology it is necessary to know mineral and organic components behavior when combustible shale is burnt. Since the first will determine slagging properties of energy raw materials, the second – its calorific value. In consideration of this the main research methods were X-ray, thermal and X-ray fluorescence analyses. Summing up the obtained results, we can draw to the following conclusions: 1. The combustible shale in Tatarstan and the Ulyanovsk region has predominantly low calorific value (Qb d = 5-9 MJ/kg). In order to enhance its efficiency and to reduce cost it is possible to conduct rocks burning together with some other organic or organic mineral power generating fuels. 2. High ash content (Ad = 60-80%) that causes a high external ballast content in shale implies the appropriateness of using this fuel resource next to its exploitation site. The acceptable distance to a consumer will reduce unproductive transportation charges for large ash and moisture masses. 3. The performed fuel ash components characteristics, as well as the yield and volatiles composition allow us to specify the basic parameters for boiler units, designed for the Volga combustible shale burning. 4. The noncombustible residual components composition shows that shale ash can be used in manufacture of materials of construction.

Study of the elastic behavior of synthetic lightweight aggregates (SLAs)

NASA Astrophysics Data System (ADS)

Jin, Na

Synthetic lightweight aggregates (SLAs), composed of coal fly ash and recycled plastics, represent a resilient construction material that could be a key aspect to future sustainable development. This research focuses on a prediction of the elastic modulus of SLA, assumed as a homogenous and isotropic composite of particulates of high carbon fly ash (HCFA) and a matrix of plastics (HDPE, LDPE, PS and mixture of plastics), with the emphasis on SLAs made of HCFA and PS. The elastic moduli of SLA with variable fly ash volume fractions are predicted based on finite element analyses (FEA) performed using the computer programs ABAQUS and PLAXIS. The effect of interface friction (roughness) between phases and other computation parameters; e.g., loading strain, stiffness of component, element type and boundary conditions, are included in these analyses. Analytical models and laboratory tests provide a baseline for comparison. Overall, results indicate ABAQUS generates elastic moduli closer to those predicted by well-established analytical models than moduli predicted from PLAXIS, especially for SLAs with lower fly ash content. In addition, an increase in roughness, loading strain indicated increase of SLAs stiffness, especially as fly ash content increases. The elastic moduli obtained from unconfined compression generally showed less elastic moduli than those obtained from analytical and ABAQUS 3D predictions. This may be caused by possible existence of pre-failure surface in specimen and the directly interaction between HCFA particles. Recommendations for the future work include laboratory measurements of SLAs moduli and FEM modeling that considers various sizes and random distribution of HCFA particles in SLAs.

Proximate and fatty acid composition and cholesterol content of different cuts of guinea fowl meat as affected by cooking method.

PubMed

Hoffman, Louwrens C; Tlhong, Tumelo M

2012-10-01

Poultry is one of the leading meat products in South Africa, and its nutritional composition can be affected by the cut and cooking method. Limited food composition data are available for typical South African poultry products. This study investigated the effect of different cuts and cooking methods on the proximate and fatty acid composition as well as the cholesterol content of guinea fowl (Numida meleagris) meat. The open-roasting method produced the highest moisture content for all cuts, and the baking bag method the lowest. The baking bag method resulted in the highest protein content. Cooking method had no effect on fat content, although breast had the lowest and thigh the highest fat content. Ash content was highest in the open-roasted drumstick. All cuts, regardless of cooking method, had a favourable polyunsaturated/saturated fatty acid (P/S) ratio (>0.4). Their n-6/n-3 ratio was also within the recommended beneficial range (<4:1). Both cooking method and cut affected cholesterol content. Different cuts of guinea fowl vary in proximate and fatty acid composition as well as in cholesterol content, which in turn is affected to varying degrees by cooking method. Copyright © 2012 Society of Chemical Industry.

Effects of Adult Feeding and Overwintering Conditions on Energy Reserves and Flight Performance of Emerald Ash Borer (Coleoptera: Buprestidae).

PubMed

Tussey, Dylan A; Aukema, Brian H; Charvoz, Anthony M; Venette, Robert C

2018-06-06

Emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), an invasive beetle from Asia, spreads through human-mediated movement and active flight. The effects of adult feeding and overwintering conditions on A. planipennis energy reserves (e.g., lipid, glycogen, and sugars) and flight are poorly understood. We conjectured that the potential energetic demands associated with the production of cryoprotectants might affect dispersal capacity and partially explain slower spread of A. planipennis in Minnesota than in the other states. Two studies sought to measure the effects of adult feeding on lipid content and flight capacity. Adult A. planipennis were fed shamel ash, Fraxinus uhdei Wenzig, leaves for 0-20 d after emergence, and half were flown on a custom flight mill for 24 h, before being frozen for comparative lipid analysis with a control group. The second study compared the effects of adult feeding on energy reserves and flight capacity of A. planipennis that were originally from St. Paul, Minnesota but overwintered in infested logs placed in Grand Rapids, Minnesota (low winter temperature, -34°C) or St. Paul, Minnesota (-26.3°C). Live adults consumed foliage at a constant rate, but lipid content (percentage of fresh mass) did not change with increases in feeding or flight. Adult glycogen content declined with flight and increased only slightly with feeding. Overwintering location affected survival rates but not energy reserves or flight capacity. These results suggest that the flight capacity of A. planipennis is largely determined before emergence, with no differences in energy reserves after cryoprotectant investment.

Physicochemical characterizations of nano-palm oil fuel ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajak, Mohd Azrul Abdul, E-mail: azrulrajak88@gmail.com; Preparatory Centre of Science and Technology, Universiti Malaysia Sabah, Jalan UMS, 88400, Kota Kinabalu, Sabah; Majid, Zaiton Abdul, E-mail: zaiton@kimia.fs.utm.my

2015-07-22

Palm Oil Fuel Ash (POFA) is known as a good supplementary cementing material due to its siliceous-rich content. The application of nanotechnology in the pozzolanic materials could invent new functions in the efficiency of physical and chemical properties of materials. Thus, the present study aims to generate nano-sized POFA and characterize the physicochemical properties of nano-palm oil fuel ash (nPOFA). The nPOFA was prepared by mechanically grinding micro POFA using a high intensity ball milling for 6 hours. The physicochemical properties of nPOFA were characterized via X-Ray Fluoresence (XRF), Scanning Emission microscopy- Energy Dispersive X-Ray (SEM-EDX), Transmission Electron Microscope (TEM)more » and X-Ray Diffraction (XRD). The particle size of nPOFA acquired from TEM analysis was in the range of 20 nm to 90 nm, while the average crystallite size calculated from XRD diffractogram was 61.5 nm. The resulting nPOFA has a BET surface area of 145.35 m{sup 2}/g, which is more than 85% increment in surface area compared to micro-sized POFA. The morphology and elemental studies showed the presence of spherical as well as irregularly shaped and fine nPOFA particles contains with high silicon content. The presence of α-quartz as the major phase of the nPOFA was identified through XRD analysis. The study concludes that nPOFA has the potential as a supplementary cementing material due to the high silica content, high surface area and the unique behaviors of nano-structured particles.« less

Gaseous fuels production from dried sewage sludge via air gasification.

PubMed

Werle, Sebastian; Dudziak, Mariusz

2014-07-01

Gasification is a perspective alternative method of dried sewage sludge thermal treatment. For the purpose of experimental investigations, a laboratory fixed-bed gasifier installation was designed and built. Two sewage sludge (SS) feedstocks, taken from two typical Polish wastewater treatment systems, were analysed: SS1, from a mechanical-biological wastewater treatment system with anaerobic stabilization (fermentation) and high temperature drying; and (SS2) from a mechanical-biological-chemical wastewater treatment system with fermentation and low temperature drying. The gasification results show that greater oxygen content in sewage sludge has a strong influence on the properties of the produced gas. Increasing the air flow caused a decrease in the heating value of the produced gas. Higher hydrogen content in the sewage sludge (from SS1) affected the produced gas composition, which was characterized by high concentrations of combustible components. In the case of the SS1 gasification, ash, charcoal, and tar were produced as byproducts. In the case of SS2 gasification, only ash and tar were produced. SS1 and solid byproducts from its gasification (ash and charcoal) were characterized by lower toxicity in comparison to SS2. However, in all analysed cases, tar samples were toxic. © The Author(s) 2014.

A fine coal circuitry study using column flotation and gravity separation. Quarterly report, 1 March 1995--31 May 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Honaker, R.Q.; Reed, S.

1995-12-31

Column flotation provides excellent recovery of ultrafine coal while producing low ash content concentrates. However, column flotation is not efficient for treating fine coal containing significant amounts of mixed-phase particles. Fortunately, enhanced gravity separation has proved to have the ability to treat the mixed-phased particles more effectively. A disadvantage of gravity separation is that ultrafine clay particles are not easily rejected. Thus, a combination of these two technologies may provide a circuit that maximizes both the ash and sulfur rejection that can be achieved by physical coal cleaning while maintaining a high energy recovery. This project is studying the potentialmore » of using different combinations of gravity separators, i.e., a Floatex hydrosizer and a Falcon Concentrator, and a proven flotation column, which will be selected based on previous studies by the principle investigator. During this reporting period, an extensive separation performance comparison between a pilot-scale Floatex Density Separator (18{times}18-inch) and an existing spiral circuit has been conducted at Kerf-McGee Coal Preparation plan for the treatment of nominally {minus}16 mesh coal. The results indicate that the Floatex is a more efficient separation device (E{sub p}=0.12) than a conventional coal spiral (E{sub p}=0.18) for Illinois seam coals. In addition, the treatment of {minus}100 mesh Illinois No. 5 fine coal from the same plant using Falcon concentrator, column flotation (Packed-Column) and their different combinations was also evaluated. For a single operation, both Falcon concentrator and column flotation can produce a clean coal product with 90% combustible recovery and 5% ash content. In the case of the combined circuit, column flotation followed by the Falcon achieved a higher combustible recovery value (about 75%) than that obtained by the individual units while maintaining an ash content less than 3%.« less

Reduction of minimum required weight of cementitious materials in WisDOT concrete mixes.

DOT National Transportation Integrated Search

2011-12-01

"This project was designed to explore the feasibility of lowering the cementitious materials content : (CMC) used in Wisconsin concrete pavement construction. The cementitious materials studied included : portland cement, fly ash, and ground granulat...

Reduction of minimum required weight of cementitious materials in WisDOT concrete mixes.

DOT National Transportation Integrated Search

2011-12-01

This project was designed to explore the feasibility of lowering the cementitious materials content : (CMC) used in Wisconsin concrete pavement construction. The cementitious materials studied included : portland cement, fly ash, and ground granulate...

Biomass fly ash incorporation in cement based materials =

NASA Astrophysics Data System (ADS)

Rajamma, Rejini

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe's energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Compost and Crude Humic Substances Produced from Selected Wastes and Their Effects on Zea mays L. Nutrient Uptake and Growth

PubMed Central

Palanivell, Perumal; Susilawati, Kasim; Ahmed, Osumanu Haruna; Majid, Nik Muhamad

2013-01-01

Production of agriculture and timber commodities leads generation of enormous quantity of wastes. Improper disposal of these agroindustrial wastes pollutes the environment. This problem could be reduced by adding value to them. Therefore, a study was carried out to analyse and compare the nutrients content of RS, RH, SD, and EFB of composts and crude humic substances; furthermore, their effect on growth, dry matter production, and nutrient uptake for Zea mays L., and selected soil chemical properties were evaluated. Standard procedures were used to analyze humic acids (HA), crude fulvic acids (CFA), crude humin (CH), soil, dry matter production and nutrient uptake. Sawdust and RS compost matured at 42 and 47 days, respectively, while RH and EFB composts were less matured at 49th day of composting. Rice straw compost had higher ash, N, P, CEC, HA, K, and Fe contents with lower organic matter, total organic carbon, and C/N and C/P ratios. The HA of sawdust compost showed higher carbon, carboxylic, K, and Ca contents compared to those of RS, RH, and EFB. Crude FA of RS compost showed highest pH, total K, Ca, Mg, and Na contents. Crude humin from RS compost had higher contents of ash, N, P, and CEC. Rice straw was superior in compost, CFA, and CH, while sawdust compost was superior in HA. Application of sawdust compost significantly increased maize plants' diameter, height, dry matter production, N, P, and cations uptake. It also reduced N, P, and K based chemical fertilizer use by 90%. Application of CH and the composts evaluated in this study could be used as an alternative for chemical fertilizers in maize cultivation. PMID:24319353

Improvement in the traditional processing method and nutritional quality of traditional extruded cassava-based snack (modified Ajogun)

PubMed Central

Obadina, Adewale O; Oyewole, Olusola B; Williams, Oluwasolabomi E

2013-01-01

This study was carried out to investigate and improve the traditional processing method and nutritional quality of the traditional cassava snack (Ajogun). Cassava root (Manihot esculenta Crantz L.) of TME 419 variety was processed into mash (40% moisture content). The cassava mash was mixed into different blends to produce fried traditional “Ajogun”, fried and baked extrudates (modified Ajogun) as snacks. These products were analyzed to determine the proximate composition including carbohydrate, fat, protein, fiber, ash, and moisture contents and functional properties such as bulk density. The results obtained for the moisture, fat, protein, and ash contents showed significant difference (P < 0.05) between the control sample and the extrudates. However, there was no significant difference (P > 0.05) in the carbohydrate and fiber contents between the three samples. There was no significant difference (P > 0.05) in the bulk density of the snacks. Also, sensory evaluation was carried out on the cassava-based snacks using the 9-point hedonic scale to determine the degree of acceptability. Results obtained showed significant difference (P < 0.05) between the extrudates and control sample in terms of appearance, taste, flavor, color, aroma, texture, and overall acceptability. The highest acceptability level of the product was at 8.04 for the control sample (traditional Ajogun). This study has shown that “Ajogun”, which is a lesser known cassava product, is rich in protein and fat. PMID:24804039

Sewage sludge conditioning with the application of ash from biomass-fired power plant

NASA Astrophysics Data System (ADS)

Wójcik, Marta; Stachowicz, Feliks; Masłoń, Adam

2018-02-01

During biomass combustion, there are formed combustion products. Available data indicates that only 29.1 % of biomass ashes were recycled in Poland in 2013. Chemical composition and sorptive properties of ashes enable their application in the sewage sludge treatment. This paper analyses the impact of ashes from biomass-combustion power plant on sewage sludge dewatering and higienisation. The results obtained in laboratory tests proved the possitive impact of biomass ashes on sewage sludge hydration reduction after dewatering and the increase of filtrate volume. After sludge conditioning with the use of biomass combustion by-products, the final moisture content decreased by approximatelly 10÷25 % in comparison with raw sewage sludge depending on the method of dewatering. The application of biomass combustion products in sewage sludge management could provide an alternative method of their utilization according to law and environmental requirements.

Determination of the floral origin of some Romanian honeys on the basis of physical and biochemical properties.

PubMed

Cimpoiu, Claudia; Hosu, Anamaria; Miclaus, Vasile; Puscas, Anitta

2013-01-01

The aim of this study was to determine the physical and biochemical properties of some Romanian honeys in order to discriminate between their floral origins. The evaluated properties were total phenolic content, total protein content, total free amino acids content, color intensity (ABS(450)), pH, ash content, antioxidant activity. Twenty-six commercial honeys from six types of flowers (acacia, sunflower, forest, polyfloral, lime and Sea Buckthorn) were investigated. All samples showed considerable variations with reference to their properties. The properties values were in the range of approved limits (according to EU legislation). The total phenolic, total protein and total free amino acids contents and color intensity varied considerably. Similarly, forest honey had the highest antioxidant activity while the lowest was found in acacia honey. Correlation between the floral origin of honeys and the physical and biochemical properties, respectively, was observed. Moreover, this study demonstrates remarkable variation in DPPH scavenging activity and content of total phenols in honey, depending on its botanic source. Copyright © 2012 Elsevier B.V. All rights reserved.

Volcanic degassing and secondary hydration of volcanic ash and scoria: Implications for paleoaltimetry and paleoclimate studies

NASA Astrophysics Data System (ADS)

Seligman, A. N.; Bindeman, I. N.

2013-12-01

The use of δD of ash as a reliable recorder of δD (and δ18O) values of paleoprecipitation in paleoclimate and paleoaltimetry research still requires experimental verification and testing. It is currently assumed that ash is deposited with a water content of no significance, and that within a few thousand years it becomes sufficiently (up to 4 wt.% H2O) hydrated, although the rate of hydration and whether or not the initial isotopic signature is held, are not well understood. We report analyses of δD and H2O of distal ash from recent eruptions (1980 Mount St. Helens, 1992 Mt. Spurr, and 1974 Volcán de Fuego) that were collected syneruption, in addition to scoria ranging in age from ~50 to 7300 years old from Klyuchevskoy volcano (Kamchatka, Russia), using the TC/EA - MAT 253 continuous flow system. Natural variability of studied samples in wt.% H2O (δD in ‰), with errors represented as 1 s.d. for the average, for recent ash eruptions, range from 0.1 × 0.07 (-102 × 4.7) for Volcán de Fuego up to 0.7 × 0.10 (-104 × 3.5) for Mount St. Helens. Ash from the Mt. Spurr eruption averaged 0.4 × 0.04 (-109 × 4.0), and we plan to also analyze ash from Mt. Pinatubo. The δD values are consistent with a magmatic degassing trend, where the last remaining water is depleted in deuterium, suggesting ash may be deposited with up to 0.7 wt.% H2O as primary magmatic water. Klyuchevskoy scoria (basaltic andesite) shows a general trend of increasing wt.% H2O with increasing age: the youngest samples (<2.0 ka) have ~0.2 wt.% water (-99 to -109 ‰), which is likely primary magmatic, while the older samples (4.7-7.3 ka) generally have a higher water concentration (~0.3-0.5 wt.%); likely local meteoric water based on δD values that are lower than degassed magmatic δD values and higher water content. The samples between ~2.3 and 3.6 ka (0.1 to 0.4 wt.% water) have variable water concentrations due to variations in porosity and therefore surface area between the different scoria. We do not observe a trend between the SiO2 wt.% (51-56 wt.%) and the water content of the samples. The δD values (between -99 × 5.6 and -121 × 1.2 per mil are near equilibrium with local postglacial meteoric waters, when incorporating a -30‰ fractionation, and provide a trend between δD and wt.% H2O, where higher water concentrations are associated with lower δD values. We also report preliminary results of δ18O in extracted water, using experimentally hydrated dacite and rhyolite glass, and a large set of natural ash (ash described above and ash from the Lava Creek Tuff of Yellowstone). These results show water-glass fractionations between -11.5 and -12.7 for experimental glasses and -2.2 to -11.4 for natural ash. We are looking into using δ18Owater in glass as a more robust and retentive proxy of past environmental waters for paleoclimate and paleoaltimetry research.

Characterization and modes of occurrence of elements in feed coal and coal combustion products from a power plant utilizing low-sulfur coal from the Powder River Basin, Wyoming

USGS Publications Warehouse

Brownfield, Michael E.; Cathcart, James D.; Affolter, Ronald H.; Brownfield, Isabelle K.; Rice, Cynthia A.; O'Connor, Joseph T.; Zielinski, Robert A.; Bullock, John H.; Hower, James C.; Meeker, Gregory P.

2005-01-01

The U.S. Geological Survey and the University of Kentucky Center for Applied Energy Research are collaborating with an Indiana utility company to determine the physical and chemical properties of feed coal and coal combustion products from a coal-fired power plant. The Indiana power plant utilizes a low-sulfur (0.23 to 0.47 weight percent S) and lowash (4.9 to 6.3 weight percent ash) subbituminous coal from the Wyodak-Anderson coal zone in the Tongue River Member of the Paleocene Fort Union Formation, Powder River Basin, Wyoming. Based on scanning electron microscope and X-ray diffraction analyses of feed coal samples, two mineral suites were identified: (1) a primary or detrital suite consisting of quartz (including beta-form grains), biotite, feldspar, and minor zircon; and (2) a secondary authigenic mineral suite containing alumino-phosphates (crandallite and gorceixite), kaolinite, carbonates (calcite and dolomite), quartz, anatase, barite, and pyrite. The primary mineral suite is interpreted, in part, to be of volcanic origin, whereas the authigenic mineral suite is interpreted, in part, to be the result of the alteration of the volcanic minerals. The mineral suites have contributed to the higher amounts of barium, calcium, magnesium, phosphorus, sodium, strontium, and titanium in the Powder River Basin feed coals in comparison to eastern coals. X-ray diffraction analysis indicates that (1) fly ash is mostly aluminate glass, perovskite, lime, gehlenite, quartz, and phosphates with minor amounts of periclase, anhydrite, hematite, and spinel group minerals; and (2) bottom ash is predominantly quartz, plagioclase (albite and anorthite), pyroxene (augite and fassaite), rhodonite, and akermanite, and spinel group minerals. Microprobe and scanning electron microscope analyses of fly ash samples revealed quartz, zircon, and monazite, euhedral laths of corundum with merrillite, hematite, dendritic spinels/ferrites, wollastonite, and periclase. The abundant calcium and magnesium mineral phases in the fly ash are attributed to the presence of carbonate, clay, and phosphate minerals in the feed coal and their alteration to new phases during combustion. The amorphous diffraction-scattering maxima or glass 'hump' appears to reflect differences in chemical composition of fly ash and bottom ash glasses. In Wyodak-Anderson fly and bottom ashes, the center point of scattering maxima is due to calcium and magnesium content, whereas the glass 'hump' of eastern fly ash reflects variation in aluminum content. The calcium- and magnesium-rich and alumino-phosphate mineral phases in the coal combustion products can be attributed to volcanic minerals deposited in peat-forming mires. Dissolution and alteration of these detrital volcanic minerals occurred either in the peat-forming stage or during coalification and diagenesis, resulting in the authigenic mineral suite. The presence of free lime (CaO) in fly ash produced from Wyodak-Anderson coal acts as a self-contained 'scrubber' for SO3, where CaO + SO3 form anhydrite either during combustion or in the upper parts of the boiler. Considering the high lime content in the fly ash and the resulting hydration reactions after its contact with water, there is little evidence that major amounts of leachable metals are mobilized in the disposal or utilization of this fly ash.

Chemical composition of the giant red sea cucumber, Parastichopus californicus, commercially harvested in Alaska

PubMed Central

Bechtel, Peter J; Oliveira, Alexandra CM; Demir, Necla; Smiley, Scott

2013-01-01

Giant red sea cucumbers, Parastichopus californicus, are commercially harvested in the U.S. Pacific Northwest; however, the nutritional and chemical properties of its edible muscle bands and body wall have not been fully elucidated. In particular are the fatty acid profiles of P. californicus tissues, which have not been documented. Sea cucumbers were delivered live and muscle bands and body wall freeze dried, vacuum packed, and stored at –30°C until analyzed. Proximate composition of freeze-dried tissues varied greatly with muscle bands being composed of 68% protein, 12% ash, 9% carbohydrate, and 5% lipids, while the body wall was composed of 47% protein, 26% ash, 15% carbohydrate, and 8% lipids. The hydroxyproline, proline, and glycine contents of the body wall were much higher than those in muscle bands, consistent with the larger amount of connective tissue. Calcium, magnesium, sodium, and iron contents were higher in the body wall than those in muscle bands, whereas the opposite was observed for zinc content. Total long-chain n-3 fatty acid contents were 19% and 32% of total fatty acids in body wall and muscle bands, respectively. Muscle bands had higher content of eicosapentaenoic acid (20:5n-3) than body wall at 22.6% and 12.3%, respectively. High content of arachidonic acid (20:4n-6) was recorded in both body wall (7.1%) and muscle bands (9.9%). Overall, the fatty acid profiles of body wall and muscle bands of P. californicus resemble those described for other species; however, the distribution and occurrence of certain fatty acids is unique to P. californicus, being representative of the fatty acid composition of temperate-polar marine organisms. The chemical characterization of freeze-dried edible tissues from P. californicus demonstrated that these products have valuable nutritional properties. The body wall, a food product of lower market value than muscle bands, could be better utilized for nutraceutical and pharmaceutical applications. PMID:24804015

Manganese Supplementation in Deer under Balanced Diet Increases Impact Energy and Contents in Minerals of Antler Bone Tissue.

PubMed

Cappelli, Jamil; Garcia, Andrés; Ceacero, Francisco; Gomez, Santiago; Luna, Salvador; Gallego, Laureano; Gambin, Pablo; Landete-Castillejos, Tomás

2015-01-01

Bone ash, collagen, Ca and P composition, are considered the main factors affecting mechanical properties in bones. However, a series of studies in bone and antler have shown that some trace minerals, such as manganese, may play a role whose importance exceeds what may be expected considering their low content. A previous study showed that a reduction in manganese in antlers during a year of late winter frosts led to generalized antler breakage in Spain, which included a reduction of 30% of cortical thickness, 27% reduction in impact energy, and 10% reduction in work to peak force. Starting for this observation, we experimentally studied the effects of manganese supplementation in adults and yearling (yearlings) red deer under a balanced diet. Subjects were 29 deer of different age classes (adult n = 19, yearlings n = 10) that were divided in a manganese injected group (n = 14) and a control group (n = 15). Antler content in ashes and minerals, intrinsic mechanical properties and cross section structure were examined at 4 points along the antler beam. A one way ANOVA (mean per antler) showed that in yearlings, manganese supplementation only increased its content and that of Fe. However, in adults, Mn supplementation increased the mean content per antler of Ca, Na, P, B, Co, Cu, K, Mn, Ni, Se (while Si content was reduced), and impact work but not Young's modulus of elasticity, bending strength or work to peak force. A GLM series on characteristics in the uppermost part examined in the antler, often showing physiological exhaustion and depletion of body stores, showed also a 16% increase in work to peak force in the antlers of the treated group. Thus, manganese supplementation altered mineral composition of antler and improved structure and some mechanical properties despite animals having a balanced diet.

Manganese Supplementation in Deer under Balanced Diet Increases Impact Energy and Contents in Minerals of Antler Bone Tissue

PubMed Central

Cappelli, Jamil; Garcia, Andrés; Ceacero, Francisco; Gomez, Santiago; Luna, Salvador; Gallego, Laureano; Gambin, Pablo; Landete-Castillejos, Tomás

2015-01-01

Bone ash, collagen, Ca and P composition, are considered the main factors affecting mechanical properties in bones. However, a series of studies in bone and antler have shown that some trace minerals, such as manganese, may play a role whose importance exceeds what may be expected considering their low content. A previous study showed that a reduction in manganese in antlers during a year of late winter frosts led to generalized antler breakage in Spain, which included a reduction of 30% of cortical thickness, 27% reduction in impact energy, and 10% reduction in work to peak force. Starting for this observation, we experimentally studied the effects of manganese supplementation in adults and yearling (yearlings) red deer under a balanced diet. Subjects were 29 deer of different age classes (adult n = 19, yearlings n = 10) that were divided in a manganese injected group (n = 14) and a control group (n = 15). Antler content in ashes and minerals, intrinsic mechanical properties and cross section structure were examined at 4 points along the antler beam. A one way ANOVA (mean per antler) showed that in yearlings, manganese supplementation only increased its content and that of Fe. However, in adults, Mn supplementation increased the mean content per antler of Ca, Na, P, B, Co, Cu, K, Mn, Ni, Se (while Si content was reduced), and impact work but not Young’s modulus of elasticity, bending strength or work to peak force. A GLM series on characteristics in the uppermost part examined in the antler, often showing physiological exhaustion and depletion of body stores, showed also a 16% increase in work to peak force in the antlers of the treated group. Thus, manganese supplementation altered mineral composition of antler and improved structure and some mechanical properties despite animals having a balanced diet. PMID:26177083

Modification of dry grain processing for rice nutrition produced

NASA Astrophysics Data System (ADS)

Rahman, A. N. F.; Genisa, J.; Dirpan, A.; Badani, A. A.

2018-05-01

Rice is a staple food for people in Indonesia that provides high energy and nutrients of up to 360 calories per 100 g. Based on the research it was known that the nutrient content in rice will increased by soaking. This is suspected because the nutrient content in the aleurone layer adsorbed to the endosperm. The purpose of this research was to know the effect of dry grain immersion on the nutrition of rice produced. The method of this research was conducted through some stages: 1. Preparation of raw materials, 2. Grain immersion, 3. Grain drying, 4. Peeling chaff, 5. Testing the nutritional value of rice. The research was processed by using factorial randomized complete random design (RCRD) with three replications. The result showed that soaking the grain for 12 hours has the highest nutritional value increases compared to the control. Proximate test resulted from the best treatment were: protein content of 8.26%, ash content of 0.42% and thiamine content of 0.023%.

Effects of baking and boiling on the nutritional and antioxidant properties of sweet potato [Ipomoea batatas (L.) Lam.] cultivars.

PubMed

Dincer, Cuneyt; Karaoglan, Mert; Erden, Fidan; Tetik, Nedim; Topuz, Ayhan; Ozdemir, Feramuz

2011-11-01

The effects of baking and boiling on the nutritional and antioxidant properties of three sweet potato cultivars (Beniazuma, Koganesengan, Kotobuki) cultivated in Turkey were investigated. The samples were analyzed for proximate composition, total phenolic content, ascorbic acid, β-carotene, antiradical activity, and free sugars. The dry matter, protein, and starch contents of the sweet potatoes were significantly changed by the treatments while the ash and crude fiber contents did not differ as significantly. The β-carotene contents of baked and boiled sweet potatoes were lower than those of fresh sweet potatoes; however, the total phenolic and ascorbic acid contents of the baked and boiled sweet potatoes were higher than those of the fresh samples. Generally, the antiradical activity of the sweet potatoes increased with the treatments. Sucrose, glucose, and fructose were quantified as free sugars in all fresh sweet potatoes; however, maltose was determined in the treated samples. In terms of the analyzed parameters, there were no explicit differences among the sweet potato cultivars.

Total phenolics, flavonoids, antioxidant activity, crude fibre and digestibility in non-traditional wheat flakes and muesli.

PubMed

Sumczynski, Daniela; Bubelova, Zuzana; Sneyd, Jan; Erb-Weber, Susanne; Mlcek, Jiri

2015-05-01

The five different types of muesli composed of non-traditional wheat flakes were prepared and analysed. Dickkopf wheat, red wheat, kamut and spelt were compared with commercial wheat flakes. Wheat flakes and muesli were assessed for basic analyses (dry matter, ash, protein, starch and fat content), total phenolic and flavonoid content, antioxidant activity (ABTS and DPPH assays), crude fibre content and in vitro digestibility. Furthermore, sensory evaluation of muesli involving scale and ranking preference tests was provided. Flakes and muesli made from Dickkopf wheat and red wheat showed the highest total phenolic and flavonoid content and, consequently, the highest antioxidant activity. Moreover, these cereals were high in crude fibre and thus were less digestible. On the other hand, the lowest total phenolic and flavonoid contents and antioxidant activity were determined in commercial flakes and muesli produced from these flakes. The flakes made from non-traditional wheat were sensorially comparable to commercial products. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Harvesting Frequency, Variety and Leaf Maturity on Nutrient Composition, Hydrogen Cyanide Content and Cassava Foliage Yield

PubMed Central

Hue, Khuc Thi; Thanh Van, Do Thi; Ledin, Inger; Wredle, Ewa; Spörndly, Eva

2012-01-01

The experiment studied the effect of harvesting frequencies and varieties on yield, chemical composition and hydrogen cyanide content in cassava foliage. Foliage from three cassava varieties, K94 (very bitter), K98-7 (medium bitter) and a local (sweet), were harvested in three different cutting cycles, at 3, 6 and 9 months; 6 and 9 months and 9 months after planting, in a 2-yr experiment carried out in Hanoi, Vietnam. Increasing the harvesting frequency increased dry matter (DM) and crude protein (CP) production in cassava foliage. The K94 variety produced higher foliage yields than the other two varieties. Dry matter, neutral detergent fibre (NDF), acid detergent fibre (ADF) and total tannin content increased with months to the first harvest, whereas CP content decreased. Hydrogen cyanide (HCN) content was lower at the first harvest than at later harvests for all cutting cycles. At subsequent harvests the content of total tannins tended to decline, while HCN content increased (p<0.05). Chemical composition differed somewhat across varieties except for total tannins and ash. Dry matter, NDF, ADF and total tannins were higher in fully matured leaves, while CP and HCN were lower in developing leaves. PMID:25049534

Effect of harvesting frequency, variety and leaf maturity on nutrient composition, hydrogen cyanide content and cassava foliage yield.

PubMed

Hue, Khuc Thi; Thanh Van, Do Thi; Ledin, Inger; Wredle, Ewa; Spörndly, Eva

2012-12-01

The experiment studied the effect of harvesting frequencies and varieties on yield, chemical composition and hydrogen cyanide content in cassava foliage. Foliage from three cassava varieties, K94 (very bitter), K98-7 (medium bitter) and a local (sweet), were harvested in three different cutting cycles, at 3, 6 and 9 months; 6 and 9 months and 9 months after planting, in a 2-yr experiment carried out in Hanoi, Vietnam. Increasing the harvesting frequency increased dry matter (DM) and crude protein (CP) production in cassava foliage. The K94 variety produced higher foliage yields than the other two varieties. Dry matter, neutral detergent fibre (NDF), acid detergent fibre (ADF) and total tannin content increased with months to the first harvest, whereas CP content decreased. Hydrogen cyanide (HCN) content was lower at the first harvest than at later harvests for all cutting cycles. At subsequent harvests the content of total tannins tended to decline, while HCN content increased (p<0.05). Chemical composition differed somewhat across varieties except for total tannins and ash. Dry matter, NDF, ADF and total tannins were higher in fully matured leaves, while CP and HCN were lower in developing leaves.

Alkaline hydrothermal conversion of fly ash filtrates into zeolites 2: utilization in wastewater treatment.

PubMed

Somerset, Vernon; Petrik, Leslie; Iwuoha, Emmanuel

2005-01-01

Filtrates were collected using a codisposal reaction wherein fly ash was reacted with acid mine drainage. These codisposal filtrates were then analyzed by X-ray Fluorescence spectrometry for quantitative determination of the SiO2 and Al2O3 content. Alkaline hydrothermal zeolite synthesis was then applied to the filtrates to convert the fly ash material into zeolites. The zeolites formed under the experimental conditions were faujasite, sodalite, and zeolite A. The use of the fly ash-derived zeolites and a commercial zeolite was explored in wastewater decontamination experiments as it was applied to acid mine drainage in different dosages. The concentrations of Ni, Zn, Cd, As, and Pb metal ions in the treated wastewater were investigated. The results of the treatment of the acid mine drainage with the prepared fly ash zeolites showed that the concentrations of Ni, Zn, Cd, and Hg were decreased as the zeolite dosages of the fly ash zeolite (FAZ1) increased.

Combustion characteristics and retention-emission of selenium during co-firing of torrefied biomass and its blends with high ash coal.

PubMed

Ullah, Habib; Liu, Guijian; Yousaf, Balal; Ali, Muhammad Ubaid; Abbas, Qumber; Zhou, Chuncai

2017-12-01

The combustion characteristics, kinetic analysis and selenium retention-emission behavior during co-combustion of high ash coal (HAC) with pine wood (PW) biomass and torrefied pine wood (TPW) were investigated through a combination of thermogravimetric analysis (TGA) and laboratory-based circulating fluidized bed combustion experiment. Improved ignition behavior and thermal reactivity of HAC were observed through the addition of a suitable proportion of biomass and torrefied. During combustion of blends, higher values of relative enrichment factors in fly ash revealed the maximum content of condensing volatile selenium on fly ash particles, and depleted level in bottom ash. Selenium emission in blends decreased by the increasing ratio of both PW and TPW. Higher reductions in the total Se volatilization were found for HAC/TPW than individual HAC sample, recommending that TPW have the best potential of selenium retention. The interaction amongst selenium and fly ash particles may cause the retention of selenium. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mercury release from fly ashes and hydrated fly ash cement pastes

NASA Astrophysics Data System (ADS)

Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

2018-04-01

The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

Influence of fly-ash produced by lignite power station on humic substances in ectohumus horizons of Podzols

NASA Astrophysics Data System (ADS)

Weber, Jerzy; Jerzykiewicz, Maria; Jamroz, Elżbieta; Kocowicz, Andrzej; Dębicka, Magdalena; Ćwieląg-Piasecka, Irmina

2017-04-01

Literature on fly-ash influence on the environment report mainly on alkalization effect on vegetation and changes in chemistry of forest floor. As far as now soils were examined only for changes in pH in surface horizons, physical properties and heavy metal solubility. Soil properties strongly depend on soil organic matter content and humic substances properties, thus their modification plays a crucial role in soil forming processes and changes in the environment. From the other side, the alkalization effects on podzolization processes and particularly on humic substances have not been recognized. The aim of this paper was to characterize changes in properties of humic substances in ectohumus horizons of Podzols affected by alkali blown out from fly-ash dumping site of power station Bełchatów, central Poland. The objects of the investigation were Podzols derived from loose quartz sand, developed under pine forest. They surround the dumping site, which was established to store wastes from lignite combustion in Bełchatów power station. The samples were collected from ectohumus horizons in direct vicinity of the dumping site (50 m) as well as in the control area (7.3 km away) in five replications. Determination of elemental composition and spectroscopic analysis (EPR, FT-IR, ICP-OES and UV-Vis) were performed for humic acids, fulvic acids and humines extracted with standard IHSS procedure. An increase of pH in ectohumus horizons caused by the influence of fly-ash leads to change in humic substances structure. Obtained results showed that humic and fulvic acids from fly-ash affected Podzols indicated higher contents of nitrogen and sulphur, as well as higher O/C and lower C/N ratios. This points out a higher degree of their humification. Also EPR analyses of humic acids and humins affected by fly-ash indicated higher metal ions concentrations. However, the increase of Mn and Fe ions concentration did not affect the Fe(III) and Mn(II) band intensities of EPR spectra. This may suggest the presence of other forms (other oxidation state) of Mn and Fe ions, that are diamagnetic and hence EPR silent. Lower g-factors values of radicals built-in humic substances extracted from fly-ash affected soils are associated with more condensed structures with lower content of oxygen functional groups. Decrease of free radicals concentration in Podzols affected by fly-ash is correlated with an increase of the transition metal ions, such as Mn(II) and Fe(III), which interact (antiferromagnetically) with semiquinone radicals built-in humic substances macromolecules. Humic acids from fly-ash affected site indicated lower values of E4/E6 ratio, which confirmed higher molecular weight of the molecules. Thus the humic fractions from ectohumus horizon of the fly-ash affected area could be described as having heavier, more complex structure then those from control area. Above mentioned modification of humic substances may contribute to restriction of the podzolization processes, and transformation of underlying eluvial horizons into transitional AE horizons. Furthermore, due to transformation and translocation of organic components, illuvial Bhs horizons can be transformed into Bs horizons.

The Effect of Volcanic Ash Composition on Ice Nucleation Affinity

NASA Astrophysics Data System (ADS)

Genareau, K. D.; Cloer, S.; Primm, K.; Woods, T.; Tolbert, M. A.

2017-12-01

Understanding the role that volcanic ash plays in ice nucleation is important for knowledge of lightning generation in both volcanic plumes and in clouds developing downwind from active volcanoes. Volcanic ash has long been suggested to influence heterogeneous ice nucleation following explosive eruptions, but determining precisely how composition and mineralogy affects ice nucleation affinity (INA) is poorly constrained. For the study presented here, volcanic ash samples with different compositions and mineral/glass contents were tested in both the deposition and immersion modes, following the methods presented in Schill et al. (2015). Bulk composition was determined with X-ray fluorescence (XRF), grain size distribution was determined with laser diffraction particle size analysis (LDPSA), and mineralogy was determined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results of the deposition-mode experiments reveal that there is no relationship between ice saturation ratios (Sice) and either mineralogy or bulk ash composition, as all samples have similar Sice ratios. In the immersion-mode experiments, frozen fractions were determined from -20 °C to -50 °C using three different amounts of ash (0.5, 1.0, and 2.0 wt% of slurry). Results from the immersion freezing reveal that the rhyolitic samples (73 wt% SiO2) nucleate ice at higher temperatures compared to the basaltic samples (49 wt% SiO2). There is no observed correlation between frozen fractions and mineral content of ash samples, but the two most efficient ice nuclei are rhyolites that contain the greatest proportion of amorphous glass (> 90 %), and are enriched in K2O relative to transition metals (MnO and TiO2), the latter of which show a negative correlation with frozen fraction. Higher ash abundance in water droplets increases the frozen fraction at all temperatures, indicating that ash amount plays the biggest role in ice nucleation. If volcanic ash can reach sufficient abundance (≥ 2 wt%) in hydrometeors, and be compositionally enriched in K2O relative to MnO and TiO2, the nucleation of ice should efficiently occur. These chemical relationships are not only important for understanding ice nucleation in volcanic plumes, but also for constraining the effect of composition on the INA of other atmospheric aerosols.

Evaluation of the Biotoxicity of Tree Wood Ashes in Zebrafish Embryos.

PubMed

Consigli, Veronica; Guarienti, Michela; Bilo, Fabjola; Benassi, Laura; Depero, Laura E; Bontempi, Elza; Presta, Marco

2016-10-01

Ashes derived from biomass combustion and used as soil fertilizers can generate negative environmental and human health risks, related to leaching of heavy metals and other putative toxic elements. Tree wood ash composition may vary depending on geographical location and surrounding industrial processes. In this study, we evaluated the biotoxicity of lixiviated tree wood ash samples from trees of the Ash (Fraxinus), Cherry (Pronus), Hazel (Corylus), and Black locust (Robinia) genus collected in an industrialized region in Northern Italy. Elemental chemical analysis of the samples was performed by total reflection X-ray fluorescence technique and their biotoxicity was assessed in zebrafish (Danio rerio) embryos. Ashes from Ash, Cherry, and Hazel trees, but not Black locust trees, had a high concentration of heavy metals and other putative toxic elements. Accordingly, a dose-dependent increase in mortality rate and morphological and teratogenic defects was observed in zebrafish embryos treated with lixiviated Ash, Cherry, and Hazel tree wood samples, whereas the toxicity of Black locust tree wood ashes was negligible. In conclusion, lixiviated wood ashes from different plants show a different content of toxic elements that correlate with their biotoxic effects on zebrafish embryos. Tree wood ashes derived from biomass combustion may represent a potential risk for the environment and human health.

Pharmacognostic Specification, Chlorogenic Acid Content, and In vitro Antioxidant Activities of Lonicera japonica Flowering Bud.

PubMed

Chaowuttikul, Chayanon; Palanuvej, Chanida; Ruangrungsi, Nijsiri

2017-01-01

Lonicera japonica Thunb. or Japanese Honeysuckle has been widely used in traditional medicine for antipyretic. To establish the pharmacognostic specification of L. japonica flowering bud in Thailand and to determine its chlorogenic acid content and in vitro antioxidant activities. Dried L. japonica flowering bud from 15 various herbal drugstores throughout Thailand were investigated for pharmacognostic specification. Their chlorogenic acid contents were quantitatively analyzed by thin layer chromatography (TLC) densitometry with winCATS software. The mobile phase for TLC development consisted of ethyl acetate: formic acid: acetic acid: water (10:1.1:1.1:2.6). Antioxidant activities were investigated by 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging, ferric ion reducing antioxidant power assay, nitric oxide scavenging assay, and β-carotene bleaching assays. Qualified L. japonica flowering bud in Thailand was presented that the contents of loss on drying, total ash, acid-insoluble ash, and water should not be >10.11%, 6.59%, 1.14%, and 10.82% by weight, respectively. The ethanol and water soluble extractive values should not be < 16.46% and 28.88% by weight, respectively. Chlorogenic acid content in L. japonica flowering bud was found to be 2.24 ± 0.50 g/100 g of crude drug. L. japonica flowering bud showed DPPH and nitric oxide scavenging activities as well as reducing power property. This pharmacognostic specification with special reference to the chlorogenic acid content can be used for quality control of L. japonica flowering bud in Thailand. The potential antioxidant of this crude drug was demonstrated in vitro . Pharmacognostic specification of Lonicera japonica flowering bud in Thailand has been establishedThe chlorogenic acid content has been quantified by thin layer chromatography-densitometryThe ethanolic extract of L. japonica flowering bud showed antioxidation potential, especially on reducing power property. Abbreviations Used: TLC: Thin layer chromatography, DPPH: 2,2-diphenyl-1-picrylhydrazyl, FRAP: Ferric ion Reducing Antioxidant Power, WHO: World Health Organization, ICH: International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use; LOD: Limit of detection; LOQ: Limit of quantitation; BHT: Butylated hydroxytoluene; FeSO 4 : Iron(II) sulfate; DMSO: Dimethyl sulfoxide; TPTZ: 2,4,6-tripyridyl-s-triazine.

Effects of calcium oxide treatment at varying moisture concentrations on the chemical composition, in situ degradability, in vitro digestibility and gas production kinetics of anaerobically stored corn stover.

PubMed

Shi, H T; Cao, Z J; Wang, Y J; Li, S L; Yang, H J; Bi, Y L; Doane, P H

2016-08-01

The objective of this study was to determine the optimum conditions for calcium oxide (CaO) treatment of anaerobically stored corn stover by in situ and in vitro methods. Four ruminally cannulated, non-lactating, non-pregnant Holstein cows were used to determine the in situ effective degradabilities of dry matter (ISDMD), organic matter (ISOMD), neutral detergent fibre (ISNDFD), in vitro organic matter disappearance (IVOMD) and gas production in 72 h (GP72h ) of corn stover. A completely randomized design involving a 3 × 3 factorial arrangement was adopted. Ground corn stover was treated with different levels of CaO (3%, 5% and 7% of dry stover) at varying moisture contents (40%, 50% and 60%) and stored under anaerobic conditions for 15 days before analysis. Compared with untreated corn stover, the CaO-treated stover had increased ash and calcium (Ca) contents but decreased aNDF and OM contents. The moisture content, CaO level and their interaction affected (p < 0.01) the content of aNDF, ash and OM, and the ratio of aNDF/OM. The greatest ISDMD, ISOMD and ISNDFD were observed when stover was treated with 7% CaO and 60% moisture, while no differences (p > 0.01) in these in situ degradability parameters were observed between the stover treated with 5% CaO at 60% moisture content and those treated with 7% CaO at 60% moisture content. Corn stover treated with 5% CaO at 50% moisture had the maximum IVOMD and GP72 h among the treatments, and there was no difference (p > 0.01) between 50% and 60% moisture. Results from this study suggested that 5% CaO applied at 60% moisture could be an effective and economical treatment combination. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

Microwave-assisted extraction of pectin from cocoa peel

NASA Astrophysics Data System (ADS)

Sarah, M.; Hanum, F.; Rizky, M.; Hisham, M. F.

2018-02-01

Pectin is a polymer of d-galacturonate acids linked by β-1,4 glycosidic bond. This study isolates pectin from cocoa peel (Theobroma cacao) using citric acid as solvent by microwave-assisted extraction method. Cocoa peels (moisture content of 10%) with citric acid solution (pH of 1.5) irradiated by microwave energy at various microwave power (180, 300, 450 and 600 W) for 10, 15, 20, 25 and 30 minutes respectively. Pectin obtained from this study was collected and filtrated by adding 96% ethanol to precipitate the pectin. The best results obtained from extraction process using microwave power of 180 Watt for 30 minutes. This combination of power and time yielded 42.3% pectin with moisture content, ash content, weight equivalent, methoxyl content and galacturonate levels were 8.08%, 5%, 833.33 mg, 6.51% and 58,08%, respectively. The result finding suggested that microwave-assisted extraction method has a great potency on the commercial pectin production.

Physico-chemical characteristics of microwave-dried wheat distillers grain with solubles.

PubMed

Mosqueda, Maria Rosario P; Tabil, Lope G; Meda, Venkatesh

2013-01-01

Laboratory-prepared samples of wheat distillers grain with solubles with varying condensed distillers solubles (CDS) content were dried under varying microwave power, and microwave convection settings using a domestic microwave oven to examine their effect on the chemical, structural, color, flow, compression, thermal, and frictional properties of the product, which is dried distillers grain with solubles (DDGS). As CDS level increased, protein and ash content increased, while fat and fiber content decreased in wheat-based DDGS. Fat content was also markedly effected by the microwave oven drying conditions. While CDS level, microwave power or microwave convection setting, and/or their interactions significantly effected a number of physical properties; results indicated that CDS level had a stronger influence compared to the other factors. DDGS samples with high CDS levels were significantly denser, finer but more differentiated in size, less flowable, and less dispersible. These also produced denser and stronger pellets.

Ultrasonic pretreatment effects on the co-pyrolysis of municipal solid waste and paper sludge through orthogonal test.

PubMed

Fang, Shiwen; Gu, Wenlu; Chen, Lin; Yu, Zhaosheng; Dai, Minquan; Lin, Yan; Liao, Yanfen; Ma, Xiaoqian

2018-06-01

In this study, the influences of ultrasonic pretreatment factors (frequency, power, treatment time) on blends of municipal solid waste (MSW) and paper sludge (PS) with additive (MgO) was explored, through orthogonal experiments design. The optimum operating condition wanted to be acquired. However, for the ultimate (H/C) and ash analysis after pretreatment, solid residue mass and oxygenates compounds contents in products, the influences of factors were in different results. With adding PS unceasingly, the contents of hydrocarbon compounds decreased. And the ultrasonic pretreatment had the obvious influence with high PS percentage. Longer treatment time resulted to the lower content of oxygenates compounds. After adding MgO, the residue mass reduced, which meant MgO had the catalytic action, and the oxygenates compounds content reduced only with 100 kHz, which had the sonochemical effect. Copyright © 2018 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Filippov, N.A.; Baidin, I.I.; Bondarev, V.A.

This article describes the recovery of low-molecular-weight acids (LMAs) in the form of a purified 70% concentrate, with subsequent utilization as a preservative for fodder in the agricultural industry. The acid water is distilled azeotropically, with butyl alcohol as the azeotropic agent. The entrainer is a mixture of butyl alcohol and butyl formate, which forms a ternary azeotrope with a boiling point of 83.6/sup 0/C. The purified 70% LMA concentrate that is obtained is a transparent liquid at 20/sup 0/C, clear or light yellow, with an odor of acetic acid. The addition of 0.4% of the LMA concentrate to amore » silage mixture with a moisture content of 84.12% (harvested in rainy weather) resulted in the reduction of the contents of protein and ash in the silage after four months, whereas the content of cellulose increased in comparison with the content in the original green mass.« less

Metals accumulations during thermal processing of sewage sludge - characterization of bottom ash and air pollution control (APC) residues

NASA Astrophysics Data System (ADS)

Kasina, Monika; Kowalski, Piotr R.; Michalik, Marek

2016-04-01

Due to increasing mass of sewage sludge, problems in its management have appeared. Over years sewage sludge was landfilled, however due to EU directives concerning environmental issues this option is no longer possible. This type of material is considered hazardous due to highly concentrated metals and harmful elements, toxic organic substances and biological components (e.g. parasites, microbes). Currently in Europe, incineration is considered to be the most reasonable method for sewage sludge treatment. As a result of sludge incineration significant amount of energy is recovered due to high calorific value of sewage sludge but bottom ash and APC residues are being produced. In this study we show the preliminary results of chemical and mineral analyses of both bottom ash and APC residues produced in fluidized bed boiler in sewage sludge incineration plant in Poland, with a special emphasis on metals which, as a part of incombustible fraction can accumulate in the residual materials after thermal processing. The bottom ash was a SiO2-P2O5-Fe2O3-CaO-Al2O3 dominated material. Main mineral phases identified in X-ray diffraction patterns were: quartz, feldspar, hematite, and phosphates (apatite and scholzite). The bottom ash was characterized by high content of Zn - 4472 mg kg-1, Cu - 665.5 mg kg-1, Pb - 138 mg kg-1, Ni - 119.5 mg kg-1, and interestingly high content of Au - 0.858 mg kg-1 The APC residues composition was dominated by soluble phases which represent more than 90% of the material. The XRD patterns indicated thenardite, halite, anhydrite, calcite and apatite as main mineral phases. The removal of soluble phases by dissolution in deionised water caused a significant mass reduction (ca. 3% of material remained on the filters). Calcite, apatite and quartz were main identified phases. The content of metals in insoluble material is relatively high: Zn - 6326 mg kg-1, Pb - 514.3 mg kg-1, Cu - 476.6 mg kg-1, Ni - 43.3 mg kg-1. The content of Cd, As, Se and Hg was noted also what can be a reason of potential environmental concerns. A significant reduction of sludge volume after incineration causes concentration of numerous elements in both types of residues. The removal of soluble fraction from APC residues caused almost a 30-fold additional concentration of elements what makes this material interesting in terms of metals recovery. A detailed identification of metals occurrences and their distribution within mineral phases will be of a great importance in determination of possibilities of their recovery. Acknowledgment: The study was supported by Polish Nacional Science Centre NCN grant No UMO-2014/15/B/ST10/04171

The role of termites in an equatorial rain forest ecosystem of West Malaysia : I. Population density, biomass, carbon, nitrogen and calorific content and respiration rate.

PubMed

Matsumoto, Tadao

1976-06-01

1. Density of nests, population number, biomass, nitrogen and carbon content, calorific content and respiration rate of termites were studied at Pasoh Forest, West Malaysia mainly with four dominant species of epigeous nest builders, Macrotermes carbonarius, Dicuspiditermes nemorosus type-a, type-b and Homallotermes foraminifer, to reveal their role in the ecosystem. 2. The density of nests or mounds was 15-41/ha in M. carbonarius, 60-110/ha in the two types of D. nemorosus and 85-165/ha in H. foraminifer. 3. The population number per nest or mound was about 88,000 in M. carbonarius, 45,000 in D. nemorosus type-a, 47,000 in D. nemorosus type-b and 13,000 in H. foraminifer. The population number per hectare was about 1.8x10 6 for M. carbonarius, 4.3x10 6 for D. nemorosus type-a, 5.2x10 6 for D. nemorosus type-b and 2.1x10 6 for H. foraminifer. 4. The ratio in number of workers to soldiers was 6.4 for M. carbonarius, 19.0 for D. nemorosus type-a, 23.1 for D. nemorosus type-b and 8.9 for H. foraminifer. The ratio in number of adults (workers plus soldiers) to larvae was 1.4 for M. carbonarius, 0.59 for D. nemorosus type-a, 1.76 for D. nemorosus type-b and 3.84 for H. foraminifer. 5. The number of adults per nest of D. nemorosus type-a, type-b and H. foraminifer was linearly correlated with the weight of nest on the log-log coordinates. 6. The ratio of dry body weight to live weight was 0.24-0.30 for workers, 0.19-0.29 for soldiers and 0.15-0.22 for larvae. 7. The ash content of termite body was 26-66% for workers, 2-24% for soldiers and 1-4% for larvae. 8. The carbon content ranged from 45% to 66% of ash-free dry weight and the nitrogen content from 5.6% to 12.6%. 9. The mean calorific value of termite body was 5.3 gcal/mg in workers and soldiers on an ash-free weight basis, but was greater in nymphs and winged reproductives in the nest (6.7-6.9 gcal/mg) owing probably to their large fat storage. 10. The relation of CO 2 evolution rate to temperature in these termites was similar to what has been found in other insects. 11. The total biomass of the four termite species was estimated at 6.01 kg ash-free dry weight/ha, equivalent to 0.55 kg nitrogen/ha and 3.09 kg carbon/ha. 12. The role of the fungi cultivated by M. carbonarius on their fungus combs was discussed in relation to the nutrition of termites and the decomposition of leaf-litter with special reference to their nitrogen metabolism. The high nitrogen content of fungus spherules growing on fungus combs seemed to have an important bearing on the nutrition of termites. 13. It was concluded that the termites played a very important role in the organic matter decomposition cycle of Pasoh Forest.

Physical properties and sixth graders' acceptance of an extruded ready-to-eat sweetpotato breakfast cereal

NASA Technical Reports Server (NTRS)

Dansby, M. Y.; Bovell-Benjamin, A. C.

2003-01-01

Extruded ready-to-eat breakfast cereals (RTEBCs) were made from varying levels of sweetpotato flour (SPF), whole-wheat bran (WWB), and extrusion cooking. Moisture, protein, and ash contents were lower in the 100% SPF than the 100% WWB. Carbohydrate, beta-carotene, and ascorbic acid contents were higher in the 100% SPF. Fat, thiamin, riboflavin contents, bulk densities, and the water absorption index were similar for the cereals. However, the expansion ratio was highest in the 100% SPF cereal. The 100% WWB had the lightest color and most fibrous morphology. Extruded RTEBC containing 100% SPF and 75%/25% SPF/WWB were well-liked and acceptable to sixth graders attending an elementary school in Auburn, Alabama, but the 100% WWB was unacceptable.

Transfer coefficient measurements of uranium to the organs of Wistar rats, as a function of the uranium content in the food.

PubMed

Arruda-Neto, J D; Likhachev, V P; Nogueira, G P; Araujo, G W; Camargo, S P; Cavalcante, G T; Cestari, A C; Craveiro, A M; Deppman, A; Ferreira, J W; Garcia, F; Geraldo, L P; Guzman, F; Helene, O M; Manso, M V; Martins, M N; Mesa, J; Oliveira, M F; Perez, G; Rodriguez, O; Tavares, M V; Vanin, V R

2001-06-01

Groups of animals (Wistar rats) were fed with rations doped with uranyl nitrate at concentrations ranging from 0.5 to 100 ppm. The uranium content in the ashes of the organs was measured by the neutron-fission track counting technique. The most striking result is that the transfer coefficients, as a function of the uranium concentration, exhibit a concave shape with a minimum around 20 ppm-U for all organs. Explanations to interpret this finding are tentatively given.

Recyclability of Concrete Pavement Incorporating High Volume of Fly Ash.

PubMed

Yoshitake, Isamu; Ishida, Takeo; Fukumoto, Sunao

2015-08-21

Recyclable concrete pavement was made from fly ash and crushed limestone sand and gravel as aggregates so that the concrete pavement could be recycled to raw materials for cement production. With the aim to use as much fly ash as possible for the sustainable development of society, while achieving adequate strength development, pavement concrete having a cement-replacement ratio of 40% by mass was experimentally investigated, focusing on the strength development at an early age. Limestone powder was added to improve the early strength; flexural strength at two days reached 3.5 MPa, the minimum strength for traffic service in Japan. The matured fly ash concrete made with a cement content of 200 kg/m3 achieved a flexural strength almost equal to that of the control concrete without fly ash. Additionally, Portland cement made from the tested fly ash concrete was tested to confirm recyclability, with the cement quality meeting the Japanese classification of ordinary Portland cement. Limestone-based recyclable fly ash concrete pavement is, thus, a preferred material in terms of sustainability.

Recyclability of Concrete Pavement Incorporating High Volume of Fly Ash

PubMed Central

Yoshitake, Isamu; Ishida, Takeo; Fukumoto, Sunao

2015-01-01

Recyclable concrete pavement was made from fly ash and crushed limestone sand and gravel as aggregates so that the concrete pavement could be recycled to raw materials for cement production. With the aim to use as much fly ash as possible for the sustainable development of society, while achieving adequate strength development, pavement concrete having a cement-replacement ratio of 40% by mass was experimentally investigated, focusing on the strength development at an early age. Limestone powder was added to improve the early strength; flexural strength at two days reached 3.5 MPa, the minimum strength for traffic service in Japan. The matured fly ash concrete made with a cement content of 200 kg/m3 achieved a flexural strength almost equal to that of the control concrete without fly ash. Additionally, Portland cement made from the tested fly ash concrete was tested to confirm recyclability, with the cement quality meeting the Japanese classification of ordinary Portland cement. Limestone-based recyclable fly ash concrete pavement is, thus, a preferred material in terms of sustainability. PMID:28793518