Radiation-induced polymerization of cyclophosphazene trimers. Final report, 1 September 1985-30 September 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stannett, V.T.

1989-01-04

Hexachlorophosphazene was irradiated in bulk and in solution after various methods of purification. When rigorously dried and purified, good yields of polymer were obtained. Poor reproducibility was found in the bulk but reasonably good results were obtained in decalin solution. The best yields and highest molecular weights were obtained after the addition of small amounts of the bulky electron acceptor pyromellitic dianhydride. Hexachlorocyclotriphosphazene was purified by recrystallization for various times from dried heptane. The trimer was then further purified by repeated sublimation steps under high vacuum. Finally the trimer was dried in the melt over rigorously baked out barium oxide.more » The monomer was then transferred to ampules or the NMR tubes for radiation and subsequent determination of the polymer content.« less

Practical Considerations of Moisture in Baled Biomass Feedstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

William A. Smith; Ian J. Bonner; Kevin L. Kenney

2013-01-01

Agricultural residues make up a large portion of the immediately available biomass feedstock for renewable energy markets. Current collection and storage methods rely on existing feed and forage practices designed to preserve nutrients and properties of digestibility. Low-cost collection and storage practices that preserve carbohydrates across a range of inbound moisture contents are needed to assure the economic and technical success of the emerging biomass industry. This study examines the movement of moisture in storage and identifies patterns of migration resulting from several on-farm storage systems and their impacts on moisture measurement and dry matter recovery. Baled corn stover andmore » energy sorghum were stored outdoors in uncovered, tarp-covered, or wrapped stacks and sampled periodically to measure moisture and dry matter losses. Interpolation between discrete sampling locations in the stack improved bulk moisture content estimates and showed clear patterns of accumulation and re-deposition. Atmospheric exposure, orientation, and contact with barriers (i.e., soil, tarp, and wrap surfaces) were found to cause the greatest amount of moisture heterogeneity within stacks. Although the bulk moisture content of many stacks remained in the range suitable for aerobic stability, regions of high moisture were sufficient to support microbial activity, thus support dry matter loss. Stack configuration, orientation, and coverage methods are discussed relative to impact on moisture management and dry matter preservation. Additionally, sample collection and data analysis are discussed relative to assessment at the biorefinery as it pertains to stability in storage, queuing, and moisture carried into processing.« less

Faecal bulking efficacy of Australasian breakfast cereals.

PubMed

Monro, John A

2002-01-01

Faecal bulk may play an important role in preventing a range of disorders of the large bowel, but as yet there is little information available on the relative faecal bulking capacities of various foods. Breakfast cereals are often promoted as a good source of potential bulk for 'inner health' because they provide dietary fibre, but their relative abilities to provide faecal bulk per se have not been described. The faecal bulking efficacy of 28 representative Australasian breakfast cereals was therefore measured. A rat model developed for the purpose, and shown to give similar responses as humans to cereal fibres, was used to measure faecal bulking efficacy as increases in fully hydrated faecal weight/100 g diet, based on precise measurements of food intake, faecal dry matter output and faecal water-holding capacity (g water held without stress/g faecal dry matter). Compared to a baseline diet containing 50% sucrose, increments in hydrated faecal weight due to 50% breakfast cereal ranged from slightly negative (Cornflakes, -2 g/100 g diet) to about 80 g/100 g diet (San Bran). Most breakfast cereals increased hydrated faecal weight by between 10 and 20 g/100 g diet from a baseline of 21 +/- 1.5 g/100 g diet, but four products containing high levels of wheat bran had an exceptionally large impact on hydrated faecal weight (increment > 20 g/100 g diet), and the changes resulted more from relative changes in dry matter output than in faecal water retention/gram. However, as faecal water retention was about 2.5 g water/g faecal dry matter on average, increases in dry matter represented large increases in faecal water load. Faecal bulking indices (FBI) for most of the breakfast cereals were less than 20 (wheat bran = 100). The content of wheat bran equivalents for faecal bulk (WBE(fb)) in the breakfast cereals was calculated from FBI. Most breakfast cereals contributed, per serve, less than 10% of a theoretical daily reference value for faecal bulk (DRV(fb) = 63 WBE(fb)/day), which was based on data from human clinical trials and dietary fibre recommendations. Based on the WBE(fb) contribution/serving that would be required to meet the DRV(fb) from the number of servings of dietary fibre sources in the CSIRO 12345+ food and nutrition plan, the results suggest that although some high bran breakfast cereals may contribute substantially to, and many are reasonable sources of, faecal bulk, for most of them, one or two servings at breakfast cannot be relied on to effectively redress shortfalls in faecal bulk elsewhere in the diet.

Critical soil bulk density for soybean growth in Oxisols

NASA Astrophysics Data System (ADS)

Keisuke Sato, Michel; Veras de Lima, Herdjania; Oliveira, Pedro Daniel de; Rodrigues, Sueli

2015-10-01

The aim of this study was to evaluate the critical soil bulk density from the soil penetration resistance measurements for soybean root growth in Brazilian Amazon Oxisols. The experiment was carried out in a greenhouse using disturbed soil samples collected from the northwest of Para characterized by different texture. The treatments consisted of a range of soil bulk densities for each soil textural class. Three pots were used for soybean growth of and two for the soil penetration resistance curve. From the fitted model, the critical soil bulk density was determined considering the penetration resistance values of 2 and 3 MPa. After sixty days, plants were cut and root length, dry mass of root, and dry mass of shoots were determined. At higher bulk densities, the increase in soil water content decreased the penetration resistance, allowing unrestricted growth of soybean roots. Regardless of soil texture, the penetration resistance of 2 and 3 MPa had a slight effect on root growth in soil moisture at field capacity and a reduction of 50% in the soybean root growth was achieved at critical soil bulk density of 1.82, 1.75, 1.51, and 1.45 Mg m-3 for the sandy loam, sandy clay loam, clayey, and very clayey soil.

Properties of extruded expandable breadfruit products

USDA-ARS?s Scientific Manuscript database

Dried breadfruit was extruded with a twin screw extruder to develop a value-added expanded fruit product. This research studied the effects of barrel temperature (120-160°C), moisture content (13-25%), feeding rate (13-25 kg/h) and screw speed (115-175rpm) on physicochemical properties (bulk densit...

Production of organic fertilizer from olive mill wastewater by combining solar greenhouse drying and composting.

PubMed

Galliou, F; Markakis, N; Fountoulakis, M S; Nikolaidis, N; Manios, T

2018-05-01

Olive mill wastewater (OMW) is generated during the production of olive oil. Its disposal is still a major environmental problem in Mediterranean countries, despite the fact that a large number of technologies have been proposed up to date. The present work examines for the first time a novel, simple and low-cost technology for OMW treatment combining solar drying and composting. In the first step, OMW was dried in a chamber inside a solar greenhouse using swine manure as a bulking agent. The mean evaporation rate was found to be 5.2 kg H 2 O/m 2 /d for a drying period of 6 months (February-August). High phenol (75%) and low nitrogen (15%) and carbon (15%) losses were recorded at the end of the solar drying process. The final product after solar drying was rich in nutrients (N: 27.8 g/kg, P: 7.3 g/kg, K: 81.6 g/kg) but still contained significant quantities of phenols (18.4 g/kg). In order to detoxify the final product, a composting process was applied as a second step with or without the use of grape marc as bulking agent. Results showed that the use of grape marc as a bulking agent at a volume ratio of 1:1 achieved a higher compost temperature profile (60 °C) than 2:1 (solar drying product: grape marc) or no use (solar drying product). The end product after the combination of solar drying and composting had the characteristics of an organic fertilizer (57% organic carbon) rich in nutrients (3.5% N, 1% P, 6.5% K) with quite low phenol content (2.9 g/kg). Finally, the use of this product for the cultivation of pepper plants approved its fertility which was found similar with commercial NPK fertilizers. Copyright © 2018 Elsevier Ltd. All rights reserved.

Methods for Tier 1 Modeling within the Training Range Environmental Evaluation and Characterization System

DTIC Science & Technology

2009-08-01

properties, part b. USLE K-Factor by Organic Matter Content Soil -Texture Classification Dry Bulk Density, g/cm3 Field Capacity, % Available...Universal Soil Loss Equation ( USLE ) can be used to estimate annual average sheet and rill erosion, A (tons/acre-yr), from the equation A R K L S...erodibility factors, K, for various soil classifications and percent organic matter content ( USLE Fact Sheet 2008). Textural Class Average Less than 2

A comparison of freeze-drying and oven-drying preparation methods for bulk and compound-specific carbon stable isotope analyses: examples using the benthic macroinvertebrates Stenopsyche marmorata and Epeorus latifolium.

PubMed

Akamatsu, Fumikazu; Suzuki, Yaeko; Kato, Yoshikazu; Yoshimizu, Chikage; Tayasu, Ichiro

2016-01-15

Carbon stable isotope analysis of bulk samples and fatty acids is an established method for tracing carbon flow pathways and reconstructing trophic interactions, but there is no consensus on which sample drying method should be used for sample preparation. The aim of this study was to determine if freeze-drying and oven-drying treatments used to prepare samples of the benthic macroinvertebrates Stenopsyche marmorata and Epeorus latifolium for bulk and fatty-acid-specific carbon stable isotope analysis yield different isotopic ratio values. Five individuals each from two species were split in half; one half was freeze-dried and the other half was oven-dried. The samples were ground and the δ(13)C values of the bulk samples and eight fatty acids were measured following combustion using an isotope ratio mass spectrometer coupled to an elemental analyzer or gas chromatography system. The mean difference in the bulk and fatty acid δ(13)C values between freeze-dried and oven-dried samples was small (≤0.1‰ in both cases), although relatively large variations were observed in individual fatty-acid-specific δ(13)C values (maximum of ≤0.9 ‰). There were no significant differences in either bulk sample or fatty-acid-specific δ(13)C values between freeze-dried or oven-dried samples of the same species. Freeze-drying and oven-drying are equally acceptable methods for preparing freshly caught S. marmorata and E. latifolium samples for bulk and fatty-acid-specific carbon stable isotope analyses. Copyright © 2015 John Wiley & Sons, Ltd.

Manufacturing of High-Concentration Monoclonal Antibody Formulations via Spray Drying-the Road to Manufacturing Scale.

PubMed

Gikanga, Benson; Turok, Robert; Hui, Ada; Bowen, Mayumi; Stauch, Oliver B; Maa, Yuh-Fun

2015-01-01

Spray-dried monoclonal antibody (mAb) powders may offer applications more versatile than the freeze-dried cake, including preparing high-concentration formulations for subcutaneous administration. Published studies on this topic, however, are generally scarce. This study evaluates a pilot-scale spray dryer against a laboratory-scale dryer to spray-dry multiple mAbs in consideration of scale-up, impact on mAb stability, and feasibility of a high-concentration preparation. Under similar conditions, both dryers produced powders of similar properties-for example, water content, particle size and morphology, and mAb stability profile-despite a 4-fold faster output by the pilot-scale unit. All formulations containing arginine salt or a combination of arginine salt and trehalose were able to be spray-dried with high powder collection efficiency (>95%), but yield was adversely affected in formulations with high trehalose content due to powder sticking to the drying chamber. Spray-drying production output was dictated by the size of the dryer operated at an optimal liquid feed rate. Spray-dried powders could be reconstituted to high-viscosity liquids, >300 cP, substantially beyond what an ultrafiltration process can achieve. The molar ratio of trehalose to mAb needed to be reduced to 50:1 in consideration of isotonicity of the formulation with mAb concentration at 250 mg/mL. Even with this low level of sugar protection, long-term stability of spray-dried formulations remained superior to their liquid counterparts based on size variant and potency data. This study offers a commercially viable spray-drying process for biological bulk storage and an option for high-concentration mAb manufacturing. This study evaluates a pilot-scale spray dryer against a laboratory-scale dryer to spray-dry multiple monoclonal antibodies (mAbs) from the perspective of scale-up, impact on mAb stability, and feasibility of a high-concentration preparation. The data demonstrated that there is no process limitation in solution viscosity when high-concentration mAb formulations are prepared from spray-dried powder reconstitution compared with concentration via the conventional ultrafiltration process. This study offers a commercially viable spray-drying process for biological bulk storage and a high-concentration mAb manufacturing option for subcutaneous administration. The outcomes of this study will benefit scientists and engineers who develop high-concentration mAb products by providing a viable manufacturing alternative. © PDA, Inc. 2015.

An estimation of the main wetting branch of the soil water retention curve based on its main drying branch using the machine learning method

NASA Astrophysics Data System (ADS)

Lamorski, Krzysztof; Šimūnek, Jiří; Sławiński, Cezary; Lamorska, Joanna

2017-02-01

In this paper, we estimated using the machine learning methodology the main wetting branch of the soil water retention curve based on the knowledge of the main drying branch and other, optional, basic soil characteristics (particle size distribution, bulk density, organic matter content, or soil specific surface). The support vector machine algorithm was used for the models' development. The data needed by this algorithm for model training and validation consisted of 104 different undisturbed soil core samples collected from the topsoil layer (A horizon) of different soil profiles in Poland. The main wetting and drying branches of SWRC, as well as other basic soil physical characteristics, were determined for all soil samples. Models relying on different sets of input parameters were developed and validated. The analysis showed that taking into account other input parameters (i.e., particle size distribution, bulk density, organic matter content, or soil specific surface) than information about the drying branch of the SWRC has essentially no impact on the models' estimations. Developed models are validated and compared with well-known models that can be used for the same purpose, such as the Mualem (1977) (M77) and Kool and Parker (1987) (KP87) models. The developed models estimate the main wetting SWRC branch with estimation errors (RMSE = 0.018 m3/m3) that are significantly lower than those for the M77 (RMSE = 0.025 m3/m3) or KP87 (RMSE = 0. 047 m3/m3) models.

Method of aeration disinfecting and drying grain in bulk and pretreating seeds and a transverse blow silo grain dryer therefor

DOEpatents

Danchenko, Vitaliy G [Dnipropetrovsk, UA; Noyes, Ronald T [Stillwater, OK; Potapovych, Larysa P [Dnipropetrovsk, UA

2012-02-28

Aeration drying and disinfecting grain crops in bulk and pretreating seeds includes passing through a bulk of grain crops and seeds disinfecting and drying agents including an ozone and air mixture and surrounding air, subdividing the disinfecting and drying agents into a plurality of streams spaced from one another in a vertical direction, and passing the streams at different heights through levels located at corresponding heights of the bulk of grain crops and seeds transversely in a substantially horizontal direction.

Water distribution at the root-soil interface: is there more water next to roots?

NASA Astrophysics Data System (ADS)

Carminati, A.; Moradi, A.; Oswald, S.; Vetterlein, D.; Weller, U.; Vogel, H.-J.

2009-04-01

Plants are big water movers and have a significant impact on soil water dynamics as well as on the global water cycle. Despite the relevance of root water uptake in terrestrial ecology, the movement of water from soil to roots still presents important open questions, e.g the following two. Which are the properties of the soil near the roots? And what effect do these properties have on soil plant water relations? Most models are based on brute-force spatial averaging of soil properties and assume that the bulk soil has the same properties as the rhizosphere. However, there is evidence in the literature that the rhizosphere has specific properties that may affect water and nutrient uptake (Young 1995, Gregory 2007). In order to investigate the rhizosphere hydraulic properties and their effect on soil plant water relations, we used neutron radiography and neutron tomography to image the water content distribution in soils during plant transpiration. Rectangular (quasi-2D) and cylindrical containers were filled with sandy soil and planted with lupins (Lupinus albus). Three weeks after planting, the samples were equilibrated at water potentials of -10 and 30 hPa and have been imaged for 5 days at intervals of 6 hours. At day 5 the samples were irrigated again via capillary rise and the water distribution was monitored for 4 more days. During the first day of the drying period, regions of water depletion formed around the central part of the tap root where first order laterals were present. As the soil dried up, the picture changed: instead of less water around the roots, as commonly supposed by models, we observed that more water was present around the lateral roots. Interestingly, these regions during drying were retaining high water content, but after irrigation remained markedly drier than the bulk soil. Our hypothesis is that high water content near roots during drying and lower water content during rewetting are explained by the presence of bio-polymers exuded by roots forming a hydrogel that consists of up to 99% water at very negative water potentials (Read et al. 1999). Thanks to its high water holding capacity, this hydrogel maintains a continuous hydraulic pathway across soil and roots for an extended period of time during drying. During rewetting it adversely affects water redistribution, like a storage that needs time to fill up again. These data show for the first time in situ the potential role of mucilage in controlling water dynamics in the rhizosphere and consequences for plant water extraction. Gregory P J, Roots, rhizosphere and soil: the route to a better understanding of soil science? European Journal of Soil Science, 57: 2-12, 2006. Read D P, Gregory P J, and Bell A E. Physical properties of axenic maize root mucilage. Plant and Soil, 211: 87-91, 1999. Young I M. Variation in moisture contents between bulk soil and the rhizosheath of wheat. New Phytologist, 130: 135-139, 1995.

Optimization of intermittent microwave–convective drying using response surface methodology

PubMed Central

Aghilinategh, Nahid; Rafiee, Shahin; Hosseinpur, Soleiman; Omid, Mahmoud; Mohtasebi, Seyed Saeid

2015-01-01

In this study, response surface methodology was used for optimization of intermittent microwave–convective air drying (IMWC) parameters with employing desirability function. Optimization factors were air temperature (40–80°C), air velocity (1–2 m/sec), pulse ratio) PR ((2–6), and microwave power (200–600 W) while responses were rehydration ratio, bulk density, total phenol content (TPC), color change, and energy consumption. Minimum color change, bulk density, energy consumption, maximum rehydration ratio, and TPC were assumed as criteria for optimizing drying conditions of apple slices in IMWC. The optimum values of process variables were 1.78 m/sec air velocity, 40°C air temperature, PR 4.48, and 600 W microwave power that characterized by maximum desirability function (0.792) using Design expert 8.0. The air temperature and microwave power had significant effect on total responses, but the role of air velocity can be ignored. Generally, the results indicated that it was possible to obtain a higher desirability value if the microwave power and temperature, respectively, increase and decrease. PMID:26286706

Uneven drying of zygotic embryos and embryonic axes of recalcitrant seeds: challenges and considerations for cryopreservation.

PubMed

Ballesteros, Daniel; Sershen; Varghese, Boby; Berjak, Patricia; Pammenter, Norman W

2014-08-01

Cryopreservation is the most promising option for the long-term germplasm conservation of recalcitrant-seeded species. However, the variable post-cryo success achieved with the excised zygotic explants traditionally used for cryopreservation has been a concern for some time. Differential drying rates amongst explants of different species, uneven drying amongst explants within a batch of seeds and uneven drying across tissues within individual embryos could be contributory factors to this variable success and these phenomena form the foci of the present study. Using zygotic explants from a range of recalcitrant-seeded species, which included sub-tropical dicotyledonous trees and sub-tropical monocotyledonous geophytes, the study showed that embryo morphology and anatomy are critical determinants of the drying characteristics of the different tissues composing the explant and hence, post-cryo survival. The results suggest that the rates of drying of explants to water contents (WCs) in the theoretically optimal range for successful cryopreservation are species-specific, and that more rapid drying rates may promote post-cryo survival. However, the large variation in WC amongst individual explants in bulk samples challenges the selection of the theoretically optimum WC for cryopreservation. As a consequence of differential drying rates across the different tissues composing explants, either lethal ice crystal damage or desiccation damage may sometimes be likely in tissues responsible for the onwards development of the embryo. Drying times for cryopreservation of such explants should, therefore, be selected on the basis of WC of segments containing root or shoot meristem, rather than embryo bulk WC. Drying intensity and duration also interact with explant morphology and embryo/axis size and anatomy to bring about - or preclude - post-cryo survival. Copyright © 2014 Elsevier Inc. All rights reserved.

Laboratory Performance of Five Selected Soil Moisture Sensors Applying Factory and Own Calibration Equations for Two Soil Media of Different Bulk Density and Salinity Levels.

PubMed

Matula, Svatopluk; Báťková, Kamila; Legese, Wossenu Lemma

2016-11-15

Non-destructive soil water content determination is a fundamental component for many agricultural and environmental applications. The accuracy and costs of the sensors define the measurement scheme and the ability to fit the natural heterogeneous conditions. The aim of this study was to evaluate five commercially available and relatively cheap sensors usually grouped with impedance and FDR sensors. ThetaProbe ML2x (impedance) and ECH₂O EC-10, ECH₂O EC-20, ECH₂O EC-5, and ECH₂O TE (all FDR) were tested on silica sand and loess of defined characteristics under controlled laboratory conditions. The calibrations were carried out in nine consecutive soil water contents from dry to saturated conditions (pure water and saline water). The gravimetric method was used as a reference method for the statistical evaluation (ANOVA with significance level 0.05). Generally, the results showed that our own calibrations led to more accurate soil moisture estimates. Variance component analysis arranged the factors contributing to the total variation as follows: calibration (contributed 42%), sensor type (contributed 29%), material (contributed 18%), and dry bulk density (contributed 11%). All the tested sensors performed very well within the whole range of water content, especially the sensors ECH₂O EC-5 and ECH₂O TE, which also performed surprisingly well in saline conditions.

Laboratory Performance of Five Selected Soil Moisture Sensors Applying Factory and Own Calibration Equations for Two Soil Media of Different Bulk Density and Salinity Levels

PubMed Central

Matula, Svatopluk; Báťková, Kamila; Legese, Wossenu Lemma

2016-01-01

Non-destructive soil water content determination is a fundamental component for many agricultural and environmental applications. The accuracy and costs of the sensors define the measurement scheme and the ability to fit the natural heterogeneous conditions. The aim of this study was to evaluate five commercially available and relatively cheap sensors usually grouped with impedance and FDR sensors. ThetaProbe ML2x (impedance) and ECH2O EC-10, ECH2O EC-20, ECH2O EC-5, and ECH2O TE (all FDR) were tested on silica sand and loess of defined characteristics under controlled laboratory conditions. The calibrations were carried out in nine consecutive soil water contents from dry to saturated conditions (pure water and saline water). The gravimetric method was used as a reference method for the statistical evaluation (ANOVA with significance level 0.05). Generally, the results showed that our own calibrations led to more accurate soil moisture estimates. Variance component analysis arranged the factors contributing to the total variation as follows: calibration (contributed 42%), sensor type (contributed 29%), material (contributed 18%), and dry bulk density (contributed 11%). All the tested sensors performed very well within the whole range of water content, especially the sensors ECH2O EC-5 and ECH2O TE, which also performed surprisingly well in saline conditions. PMID:27854263

Identification of locally available structural material as co-substrate for organic waste composting in Tamil Nadu, India.

PubMed

Springer, C; Heldt, N

2016-06-01

Owing to the lack in structural strength while composting certain kinds of organic wastes, 11 co-substrates were tested that are generally locally available in rural areas of northern Tamil Nadu, India. In addition to the classical composting parameters such as carbon/nitrogen ratio, moisture content, dry matter and organic dry matter, a compression test was conducted to evaluate the structural strength and the suitability as bulking agent for composting processes. Additionally, with respect to the climatic conditions in India, the water holding capacity was also evaluated. © The Author(s) 2016.

Development of a novel dry powder inhalation formulation for the delivery of rivastigmine hydrogen tartrate.

PubMed

Simon, Alice; Amaro, Maria Inês; Cabral, Lucio Mendes; Healy, Anne Marie; de Sousa, Valeria Pereira

2016-03-30

The purpose of this study was to prepare engineered particles of rivastigmine hydrogen tartrate (RHT) and to characterize the physicochemical and aerodynamic properties, in comparison to a lactose carrier formulation (LCF). Microparticles were prepared from ethanol/water solutions containing RHT with and without the incorporation of L-leucine (Leu), using a spray dryer. Dry powder inhaler formulations prepared were characterized by scanning electron microscopy, powder X-ray diffraction, laser diffraction particle sizing, ATR-FTIR, differential scanning calorimetry, bulk and tapped density, dynamic vapour sorption and in vitro aerosol deposition behaviour using a next generation impactor. The smooth-surfaced spherical morphology of the spray dried microparticles was altered by adding Leu, resulting in particles becoming increasingly wrinkled with increasing Leu. Powders presented low densities. The glass transition temperature was sufficiently high (>90 °C) to suggest good stability at room temperature. As Leu content increased, spray dried powders presented lower residual solvent content, lower particle size, higher fine particle fraction (FPF<5 μm), and lower mass median aerodynamic diameter (MMAD). The LCF showed a lower FPF and higher MMAD, relative to the spray dried formulations containing more than 10% Leu. Spray dried RHT powders presented better aerodynamic properties, constituting a potential drug delivery system for oral inhalation. Copyright © 2016. Published by Elsevier B.V.

Active moss biomonitoring of trace elements with Sphagnum girgensohnii moss bags in relation to atmospheric bulk deposition in Belgrade, Serbia.

PubMed

Anicić, M; Tasić, M; Frontasyeva, M V; Tomasević, M; Rajsić, S; Mijić, Z; Popović, A

2009-02-01

Active biomonitoring with wet and dry moss bags was used to examine trace element atmospheric deposition in the urban area of Belgrade. The element accumulation capability of Sphagnum girgensohnii Russow was tested in relation to atmospheric bulk deposition. Moss bags were mounted for five 3-month periods (July 2005-October 2006) at three representative urban sites. For the same period monthly bulk atmospheric deposition samples were collected. The concentrations of Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Cd, and Pb were determined by instrumental neutron activation analyses and atomic absorption spectrometry. Significant accumulation of most elements occurred in the exposed moss bags compared with the initial moss content. High correlations between the elements in moss and bulk deposits were found for V, Cu, As, and Ni. The enrichment factors of the elements for both types of monitor followed the same pattern at the corresponding sites.

Comparison of blueberry powder produced via foam-mat freeze-drying versus spray-drying: evaluation of foam and powder properties.

PubMed

Darniadi, Sandi; Ho, Peter; Murray, Brent S

2018-03-01

Blueberry juice powder was developed via foam-mat freeze-drying (FMFD) and spray-drying (SD) via addition of maltodextrin (MD) and whey protein isolate (WPI) at weight ratios of MD/WPI = 0.4 to 3.2 (with a fixed solids content of 5 wt% for FMFD and 10 wt% for SD). Feed rates of 180 and 360 mL h -1 were tested in SD. The objective was to evaluate the effect of the drying methods and carrier agents on the physical properties of the corresponding blueberry powders and reconstituted products. Ratios of MD/WPI = 0.4, 1.0 and 1.6 produced highly stable foams most suitable for FMFD. FMFD gave high yields and low bulk density powders with flake-like particles of large size that were also dark purple with high red values. SD gave low powder recoveries. The powders had higher bulk density and faster rehydration times, consisting of smooth, spherical and smaller particles than in FMFD powders. The SD powders were bright purple but less red than FMFD powders. Solubility was greater than 95% for both FMFD and SD powders. The FMFD method is a feasible method of producing blueberry juice powder and gives products retaining more characteristics of the original juice than SD. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Effect of MoSi2 Content on Dry Sliding Tribological Properties of Zr-Based Bulk Metallic Glass Composites

NASA Astrophysics Data System (ADS)

Liu, Longfei; Yang, Jun

2017-12-01

Zr55Cu30Al10Ni5 bulk metallic glass and its composites were prepared by suction casting into a copper mold. The effect of MoSi2 content on the tribological behavior of Zr55Cu30Al10Ni5 BMG was studied by using a high-speed reciprocating friction and wear tester. The results indicate that the friction coefficient and wear resistance of the BMGs can be improved by a certain amount of crystalline phase induced by MoSi2 content from 1 to 3% and deteriorated with MoSi2 content of 4%. The wear mechanism of both the metallic glass and its composite is abrasive wear. The mechanism of crystalline phase-dependent tribological properties of the composite was discussed based on the wear track and mechanical properties in the present work. The wear behavior of Zr55Cu30Al10Ni5 BMG and its composite indicates that a good combination of the toughness and the hardness can make the composite be well wear resistant.

The effect of grain size and cement content on index properties of weakly solidified artificial sandstones

NASA Astrophysics Data System (ADS)

Atapour, Hadi; Mortazavi, Ali

2018-04-01

The effects of textural characteristics, especially grain size, on index properties of weakly solidified artificial sandstones are studied. For this purpose, a relatively large number of laboratory tests were carried out on artificial sandstones that were produced in the laboratory. The prepared samples represent fifteen sandstone types consisting of five different median grain sizes and three different cement contents. Indices rock properties including effective porosity, bulk density, point load strength index, and Schmidt hammer values (SHVs) were determined. Experimental results showed that the grain size has significant effects on index properties of weakly solidified sandstones. The porosity of samples is inversely related to the grain size and decreases linearly as grain size increases. While a direct relationship was observed between grain size and dry bulk density, as bulk density increased with increasing median grain size. Furthermore, it was observed that the point load strength index and SHV of samples increased as a result of grain size increase. These observations are indirectly related to the porosity decrease as a function of median grain size.

Assessment of (222)Rn emanation from ore body and backfill tailings in low-grade underground uranium mine.

PubMed

Mishra, Devi Prasad; Sahu, Patitapaban; Panigrahi, Durga Charan; Jha, Vivekanand; Patnaik, R Lokeswara

2014-02-01

This paper presents a comparative study of (222)Rn emanation from the ore and backfill tailings in an underground uranium mine located at Jaduguda, India. The effects of surface area, porosity, (226)Ra and moisture contents on (222)Rn emanation rate were examined. The study revealed that the bulk porosity of backfill tailings is more than two orders of magnitude than that of the ore. The geometric mean radon emanation rates from the ore body and backfill tailings were found to be 10.01 × 10(-3) and 1.03 Bq m(-2) s(-1), respectively. Significant positive linear correlations between (222)Rn emanation rate and the (226)Ra content of ore and tailings were observed. For normalised (226)Ra content, the (222)Rn emanation rate from tailings was found to be 283 times higher than the ore due to higher bulk porosity and surface area. The relative radon emanation from the tailings with moisture fraction of 0.14 was found to be 2.4 times higher than the oven-dried tailings. The study suggested that the mill tailings used as a backfill material significantly contributes to radon emanation as compared to the ore body itself and the (226)Ra content and bulk porosity are the dominant factors for radon emanation into the mine atmosphere.

Bioavailability of coated and uncoated ZnO nanoparticles to cucumber in soil with or without organic matter.

PubMed

Moghaddasi, Sahar; Fotovat, Amir; Khoshgoftarmanesh, Amir Hossein; Karimzadeh, F; Khazaei, Hamid Reza; Khorassani, Reza

2017-10-01

There is a gap of knowledge for the fate, effects and bioavailability of coated and uncoated ZnO nanoparticles (NPs) in soil. Moreover, little is known about the effects of soil properties on effects of NPs on plants. In this study, the availability ZnO NPs in two soils with different organic matter content (one treated with cow manure (CM) and the other as untreated) was compared with their bulk particles. Results showed that coated and uncoated ZnO NPs can be more bioaccessible than their bulk counterpart and despite their more positive effects at low concentration (< 100mgkg -1 ), they were more phytotoxic for plants compared to the bulk ZnO particles at high concentration (1000mgkg -1 ) in the soil untreated with CM. The concentration of 1000mgkg -1 of ZnO NPs, decreased shoot dry biomass (52%) in the soil untreated with CM but increased shoot dry biomass (35%) in CM-treated soil compared to their bulk counterpart. In general, plants in the CM-treated soil showed higher Zn concentration in their tissues compared with those in untreated soil. The difference in shoot Zn concentration between CM-treated and untreated soil for NPs treatments was more than bulk particles treatment. This different percentage at 100mgkg -1 of bulk particles was 20.6% and for coated and uncoated NPs were 37% and 32%, respectively. Generally, the distribution of ZnO among Zn fractions in soil (exchangeable, the metal bound to carbonates, Fe-Mn oxides, organic matter and silicate minerals and the residual fraction) changed based on applied Zn concentration, Zn source and soil organic matter content. The root tip deformation under high concentration of NPs (1000mgkg -1 treatment ) was observed by light microscopy in plants at the soil untreated with CM. It seems that root tip deformation is one of the specific effects of NPs which in turn inhibits plant growth and nutrients uptake by root. The transmission electron microcopy image showed the aggregation of NPs inside the plant cytoplasm and their accumulation adjacent to the cell membrane. Copyright © 2017. Published by Elsevier Inc.

Effects of Water on Structure and Dynamics of Trehalose Glasses at Low Water Contents and its Relationship to Preservation Outcomes

NASA Astrophysics Data System (ADS)

Weng, Lindong; Ziaei, Shima; Elliott, Gloria D.

2016-07-01

Dry preservation of biologics in sugar glasses is regarded as a promising alternative to conventional cryopreservation. Evidence from various studies has suggested that there is a critical range of water content beyond which the viability of preserved biologics can be greatly compromised. In this study the viability of T-cells was determined as a function of end water content after microwave-assisted drying in trehalose solutions. Hydrogen-bonding and clustering phenomena in trehalose solutions of the same moisture content were also evaluated using molecular dynamics simulation. Post-rehydration viability decreased dramatically within the range of 0.1-1 gH2O/gdw. Molecular modeling revealed that as the water content approached 0.1 gH2O/gdw the matrix formed a large interconnected trehalose skeleton with a minimal number of bound water molecules scattered in the bulk. The diffusion coefficients of trehalose oxygen atoms most distant from the glycosidic linkage fluctuated around 7.5 × 10-14 m2/s within the range of 0.02-0.1 gH2O/gdw and increased again to ~1.13 × 10-13 m2/s at 0.01 gH2O/gdw and below due to the loss of water in the free volume between trehalose molecules. These insights can guide the optimal selection of final moisture contents to advance dry preservation methods.

Effects of Water on Structure and Dynamics of Trehalose Glasses at Low Water Contents and its Relationship to Preservation Outcomes.

PubMed

Weng, Lindong; Ziaei, Shima; Elliott, Gloria D

2016-07-08

Dry preservation of biologics in sugar glasses is regarded as a promising alternative to conventional cryopreservation. Evidence from various studies has suggested that there is a critical range of water content beyond which the viability of preserved biologics can be greatly compromised. In this study the viability of T-cells was determined as a function of end water content after microwave-assisted drying in trehalose solutions. Hydrogen-bonding and clustering phenomena in trehalose solutions of the same moisture content were also evaluated using molecular dynamics simulation. Post-rehydration viability decreased dramatically within the range of 0.1-1 gH2O/gdw. Molecular modeling revealed that as the water content approached 0.1 gH2O/gdw the matrix formed a large interconnected trehalose skeleton with a minimal number of bound water molecules scattered in the bulk. The diffusion coefficients of trehalose oxygen atoms most distant from the glycosidic linkage fluctuated around 7.5 × 10(-14) m(2)/s within the range of 0.02-0.1 gH2O/gdw and increased again to ~1.13 × 10(-13) m(2)/s at 0.01 gH2O/gdw and below due to the loss of water in the free volume between trehalose molecules. These insights can guide the optimal selection of final moisture contents to advance dry preservation methods.

SI-Traceable Water Content Measurements in Solids, Bulks, and Powders

NASA Astrophysics Data System (ADS)

Østergaard, Peter; Nielsen, Jan

2018-01-01

Methods such as Karl Fischer titration and Loss-on-Drying, commonly used for estimating moisture content in samples, have been in existence for many years, but have difficulties obtaining a direct calibration chain toward water content. In recognition of this challenge, the joint research project, METefnet, was funded by the European Metrology Research Programme in 2012. The goal of METefnet is to establish a European metrology infrastructure for water content measurement and to develop primary standards for unambiguous determination of water mass fraction in materials. Here, we describe the primary standard developed by Danish Technological Institute in METefnet. This standard establishes traceability of the water content of a sample to dewpoint temperature. The standard only measures water, and the measurement result is not affected by other components.

Physics of direct-contact ultrasonic cloth drying process

DOE PAGES

Peng, Chang; Ravi, Saitej; Patel, Viral K.; ...

2017-02-27

Existing methods of drying fabrics involve energy-intensive thermal evaporation of moisture from clothes. Drying fabrics using high-frequency vibrations of piezoelectric transducers can substantially reduce drying time and energy consumption. In this method, vibrational energy generates instability on the liquid-air interface and mechanically ejects water from a wet fabric. For the first time, the physics of the ultrasonic fabric drying process in direct-contact mode is studied. The kinematic and thermal responses of water droplets and fabrics on piezoelectric crystal transducers and metal mesh–based transducers are studied. The results suggest that on piezoelectric crystal transducers, the response of a droplet subjected tomore » ultrasonic excitation is dictated by the relative magnitude of the surface tension and the ultrasonic excitation forces. The drying process for a fabric on the studied transducers consists of two regimes—vibrational and thermal. When the water content is high, the vibrational forces can eject bulk water rapidly. But the more strongly bound water within the smaller fabric pores evaporates by the thermal energy generated as a result of the viscous losses. Our study finds that a metal mesh–based transducer is more suitable for dewatering fabrics, as it facilitates the ejection of water from the fabric–transducer interface to the opposite side of the mesh. A demonstration unit developed consumes 10–20% of the water latent heat energy at water contents greater than 20%.« less

Physics of direct-contact ultrasonic cloth drying process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, Chang; Ravi, Saitej; Patel, Viral K.

Existing methods of drying fabrics involve energy-intensive thermal evaporation of moisture from clothes. Drying fabrics using high-frequency vibrations of piezoelectric transducers can substantially reduce drying time and energy consumption. In this method, vibrational energy generates instability on the liquid-air interface and mechanically ejects water from a wet fabric. For the first time, the physics of the ultrasonic fabric drying process in direct-contact mode is studied. The kinematic and thermal responses of water droplets and fabrics on piezoelectric crystal transducers and metal mesh–based transducers are studied. The results suggest that on piezoelectric crystal transducers, the response of a droplet subjected tomore » ultrasonic excitation is dictated by the relative magnitude of the surface tension and the ultrasonic excitation forces. The drying process for a fabric on the studied transducers consists of two regimes—vibrational and thermal. When the water content is high, the vibrational forces can eject bulk water rapidly. But the more strongly bound water within the smaller fabric pores evaporates by the thermal energy generated as a result of the viscous losses. Our study finds that a metal mesh–based transducer is more suitable for dewatering fabrics, as it facilitates the ejection of water from the fabric–transducer interface to the opposite side of the mesh. A demonstration unit developed consumes 10–20% of the water latent heat energy at water contents greater than 20%.« less

The Human Resource Management in Dry-Bulk Shipping

NASA Astrophysics Data System (ADS)

Konstantopoulos, Nikolaos; Alexopoulos, Aristotelis B.

2007-12-01

This article investigates some positions and human resource management practices in dry-bulk shipping. The particularity of the human resource management field, as well as the crews' nationality change that has occurred over the last years, underpin the configuration of the hypothesis of this present research. The results demonstrate that the Greek dry-bulk shipping is going through a transition phase regarding the sector of the ships' human resource management by the captains.

Preparation and Characterization of Ato Nanoparticles by Coprecipitation with Modified Drying Method

NASA Astrophysics Data System (ADS)

Liu, Shimin; Liang, Dongdong; Liu, Jindong; Jiang, Weiwei; Liu, Chaoqian; Ding, Wanyu; Wang, Hualin; Wang, Nan

Antimony-doped tin oxide (ATO) nanoparticles were prepared by coprecipitation by packing drying and traditional direct drying (for comparison) methods. The as-prepared ATO nanoparticles were characterized by TG, XRD, EDS, TEM, HRTEM, BET, bulk density and electrical resistivity measurements. Results indicated that the ATO nanoparticles obtained by coprecipitation with direct drying method featured hard-agglomerated morphology, high bulk density, low surface area and low electrical resistivity, probably due to the direct liquid evaporation during drying, the fast shrinkage of the precipitate, the poor removal efficiency of liquid molecules and the hard agglomerate formation after calcination. Very differently, the ATO product obtained by the packing and drying method featured free-agglomerated morphology, low bulk density, high surface area and high electrical resistivity ascribed probably to the formed vapor cyclone environment and liquid evaporation-resistance, avoiding fast liquid removal and improving the removal efficiency of liquid molecules. The intrinsic formation mechanism of ATO nanoparticles from different drying methods was illustrated based on the dehydration process of ATO precipitates. Additionally, the packing and drying time played key roles in determining the bulk density, morphology and electrical conductivity of ATO nanoparticles.

Milling induced amorphisation and recrystallization of α-lactose monohydrate.

PubMed

Badal Tejedor, Maria; Pazesh, Samaneh; Nordgren, Niklas; Schuleit, Michael; Rutland, Mark W; Alderborn, Göran; Millqvist-Fureby, Anna

2018-02-15

Preprocessing of pharmaceutical powders is a common procedure to condition the materials for a better manufacturing performance. However, such operations may induce undesired material properties modifications when conditioning particle size through milling, for example. Modification of both surface and bulk material structure will change the material properties, thus affecting the processability of the powder. Hence it is essential to control the material transformations that occur during milling. Topographical and mechanical changes in surface properties can be a preliminary indication of further material transformations. Therefore a surface evaluation of the α-lactose monohydrate after short and prolonged milling times has been performed. Unprocessed α-lactose monohydrate and spray dried lactose were evaluated in parallel to the milled samples as reference examples of the crystalline and amorphous lactose structure. Morphological differences between unprocessed α-lactose, 1 h and 20 h milled lactose and spray dried lactose were detected from SEM and AFM images. Additionally, AFM was used to simultaneously characterize particle surface amorphicity by measuring energy dissipation. Extensive surface amorphicity was detected after 1 h of milling while prolonged milling times showed only a moderate particle surface amorphisation. Bulk material characterization performed with DSC indicated a partial amorphicity for the 1 h milled lactose and a fully amorphous thermal profile for the 20 h milled lactose. The temperature profiles however, were shifted somewhat in the comparison to the amorphous reference, particularly after extended milling, suggesting a different amorphous state compared to the spray-dried material. Water loss during milling was measured with TGA, showing lower water content for the lactose amorphized through milling compared to spray dried amorphous lactose. The combined results suggest a surface-bulk propagation of the amorphicity during milling in combination with a different amorphous structural conformation to that of the amorphous spray dried lactose. The hardened surface may be due to either surface crystallization of lactose or to formation of a low-water glass transition. Copyright © 2017 Elsevier B.V. All rights reserved.

Uptake of CeO2 nanoparticles and its effect on growth of Medicago arborea In vitro plantlets.

PubMed

Gomez-Garay, Aranzazu; Pintos, Beatriz; Manzanera, Jose Antonio; Lobo, Carmen; Villalobos, Nieves; Martín, Luisa

2014-10-01

The present study analyzes some effects of nano-CeO2 particles on the growth of in vitro plantlets of Medicago arborea when the nanoceria was added to the culture medium. Various concentrations of nano-CeO2 and bulk ceric oxide particles in suspension form were introduced to the agar culture medium to compare the effects of nanoceria versus ceric oxide bulk material. Germination rate and shoot dry weight were not affected by the addition of ceric oxide to the culture media. Furthermore, no effects were observed on chlorophyll content (single-photon avalanche diode (SPAD) measurements) due to the presence of either nano- or micro-CeO2 in the culture medium. When low concentrations of nanoceria were added to the medium, the number of trifoliate leaves and the root length increased but the root dry weight decreased. Also the values of maximum photochemical efficiency of PSII (F(v)/F m) showed a significant decrease. Dark-adapted minimum fluorescence (F 0) significantly increased in the presence of 200 mg L(-1) nanoceria and 400 mg L(-1) bulk material. Root tissues were more sensitive to nanoceria than were the shoots at lower concentrations of nanoceria. A stress effect was observed on M. arborea plantlets due to cerium uptake.

Optimizing spray drying conditions of sour cherry juice based on physicochemical properties, using response surface methodology (RSM).

PubMed

Moghaddam, Arasb Dabbagh; Pero, Milad; Askari, Gholam Reza

2017-01-01

In this study, the effects of main spray drying conditions such as inlet air temperature (100-140 °C), maltodextrin concentration (MDC: 30-60%), and aspiration rate (AR) (30-50%) on the physicochemical properties of sour cherry powder such as moisture content (MC), hygroscopicity, water solubility index (WSI), and bulk density were investigated. This investigation was carried out by employing response surface methodology and the process conditions were optimized by using this technique. The MC of the powder was negatively related to the linear effect of the MDC and inlet air temperature (IT) and directly related to the AR. Hygroscopicity of the powder was significantly influenced by the MDC. By increasing MDC in the juice, the hygroscopicity of the powder was decreased. MDC and inlet temperature had a positive effect, but the AR had a negative effect on the WSI of powder. MDC and inlet temperature negatively affected the bulk density of powder. By increasing these two variables, the bulk density of powder was decreased. The optimization procedure revealed that the following conditions resulted in a powder with the maximum solubility and minimum hygroscopicity: MDC = 60%, IT = 134 °C, and AR = 30% with a desirability of 0.875.

House dust in seven Danish offices

NASA Astrophysics Data System (ADS)

Mølhave, L.; Schneider, T.; Kjærgaard, S. K.; Larsen, L.; Norn, S.; Jørgensen, O.

Floor dust from Danish offices was collected and analyzed. The dust was to be used in an exposure experiment. The dust was analyzed to show the composition of the dust which can be a source of airborne dust indoors. About 11 kg of dust from vacuum cleaner bags from seven Danish office buildings with about 1047 occupants (12 751 m 2) was processed according to a standardized procedure yielding 5.5 kg of processed bulk dust. The bulk dust contained 130.000-160.000 CFU g -1 microorganisms and 71.000-90.000 CFU g -1 microfungi. The content of culturable microfungi was 65-123 CFU 30 g -1 dust. The content of endotoxins ranged from 5.06-7.24 EU g -1 (1.45 ng g -1 to 1.01 ng g -1). Allergens (ng g -1) were from 147-159 (Mite), 395-746 (dog) and 103-330 (cat). The macro molecular organic compounds (the MOD-content) varied from 7.8-9.8 mg g -1. The threshold of release of histamine from basophil leukocytes provoked by the bulk dust was between 0.3 and 1.0 mg ml -1. The water content was 2% (WGT) and the organic fraction 33%. 6.5-5.9% (dry) was water soluble. The fiber content was less than 0.2-1.5% (WGT) and the desorbable VOCs was 176-319 μg g -1. Most of the VOC were aldehydes. However, softeners for plastic (DBP and DEHP) were present. The chemical composition includes human and animal skin fragments, paper fibers, glass wool, wood and textilefibers and inorganic and metal particles. The sizes ranged from 0.001-1 mm and the average specific density was 1.0 g m -3. The bulk dust was resuspended and injected into an exposure chamber. The airborne dust was sampled and analyzed to illustrate the exposures that can result from sedimented dirt and dust. The airborne dust resulting from the bulk dust reached concentrations ranging from 0.26-0.75 mg m -3 in average contained 300-170 CFU m -3. The organic fraction was from 55-70% and the water content about 2.5% (WGT). The content of the dust was compared to the similar results reported in the literature and its toxic potency is estimated to be relatively low. The storage of the bulk dust during the experiment had little effect on the specific biological and chemical composition.

Development of freeze-dried albumin-free formulation of recombinant factor VIII SQ.

PubMed

Osterberg, T; Fatouros, A; Mikaelsson, M

1997-07-01

To develop a stable freeze-dried formulation of recombinant factor VIII-SQ (r-VIII SQ) without the addition of albumin. Different formulations were evaluated for their protective effect during sterile filtration, freeze-thawing, freeze-drying, reconstitution and long term storage. Factor VIII activity (VIII:C), visual inspection, clarity, solubility, moisture content and soluble aggregates and/ or fragments were assayed. A combination of non-crystallising excipients (L-histidine and sucrose), a non-ionic surfactant (polysorbate 80) and a crystalline bulking agent (sodium chloride) was found to preserve the factor VIII activity during formulation, freeze-drying and storage. Calcium chloride was included to prevent dissociation of the heavy and light chains of r-VIII SQ. Sodium chloride was chosen as the primary bulking agent since the concentration of sodium chloride necessary for dissolution of r-VIII SQ in the buffer will inhibit the crystallization of many potential cake formers. It was found that L-histidine, besides functioning as a buffer, also protected r-VIII SQ during freeze-drying and storage. A pH close to 7 was found to be optimal. Some potential macromolecular stabilisers, PEG 4000, Haes-steril and Haemaccel, were evaluated but they did not improve the recovery of VIII:C. The freeze-dried formulation was stable for at least two years at 7 degrees C and for at least one year at 25 degrees C. The reconstituted solution was stable for at least 100 hours at 25 degrees C. The albumin-free formulation resulted in consistently high recovery of VIII:C, very low aggregate formation and good storage stability. The stability of the reconstituted solution makes the formulation suitable for continuous administration via infusion pump. The formulation strategy described here may also be useful for other proteins which require a high ionic strength.

Late Quaternary carbonate accumulation along eastern South Atlantic Ocean

NASA Astrophysics Data System (ADS)

Crabill, K.; Slowey, N. C.; Foreman, A. D.; Charles, C.

2016-12-01

Water masses originating from both the North Atlantic Ocean and the Southern Ocean intersect the Walvis Ridge and Namibian margin of southwest Africa. Changes in the distribution and properties of these water masses through time are reflected by variations in the nature of the sediments accumulating along this margin. A suite of piston and gravity cores that possess sediment records corresponding to the most recent glacial-interglacial cycles were collected from the water depth range of 550 to 3700 meters. Sediment dry bulk density, XRF analyses and the concentration of CaCO3 were precisely determined at regular depth intervals in these cores. Foraminiferal δ18O along with XRF Fe/Ca data provide an age-depth model for key cores. The age-depth model and dry bulk density will be used with the calcium carbonate contents to calculate the accumulation rates of CaCO3 during each MIS 1-5e. The spatial and temporal variability in both the CaCO3 content and the CaCO3 mass accumulation rates along the Namibian continental slope will be described. Based on comparisons of these two parameters, inferences will be made about how variations of CaCO3 production, dilution of by non-CaCO3 sediment components, and dissolution of CaCO3 due to changes in ocean circulation/climate have occurred during intervals of the last glacial-interglacial cycle.

The effects of trawling on the properties of surface sediments in the Lagoon of Venice, Italy.

NASA Astrophysics Data System (ADS)

Aspden, R.; Vardy, S.; Perkins, R.; Davidson, I.; Paterson, D. M.

2003-04-01

The effects of trawling for clams in two differently impacted areas of the Lagoon of Venice were investigated. The Lagoon has an area of 55,000 hectares and the trawling of clams (Tapes phippinarum) has important socio-economic and environmental implications for the area. Bottom trawling has been shown to have large disruptive effects on the structure of benthic communities but the relationship of this to the stability and structure of the surface sediments is still unclear. The sediment stability, grain size, bulk and colloidal carbohydrate content, total organic carbon, chlorophyll a content, and sediment dry bulk density were measured in order to determine the effects of dredging on the physical and biological properties of the lagoon surface sediments. The sediments were more stable at the less impacted site and biological measurements from the same site indicated a relatively low capacity for biogenic stabilisation of sediments. Measurements were taken before and after trawling had occurred. At the less impacted site all biological properties were significantly different before and after the disturbance event, the only physical property to be significantly different was water content. At the highly impacted site the disturbance event had only a small effect on the biological and physical properties of the sediments. Only chlorophyll a content was significantly different before and after the trawl. The results suggest that frequent trawling of the lagoon will reduce the stability of the surface sediments due to the effects on the bulk strength of the sediments and on the biological status of the surface sediments.

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... inflatable hopper gate seals on Great Lakes bulk dry cargo vessels. (a) It is the duty of the Master to ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... inflatable hopper gate seals on Great Lakes bulk dry cargo vessels. (a) It is the duty of the Master to ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

Optimization of a pharmaceutical freeze-dried product and its process using an experimental design approach and innovative process analyzers.

PubMed

De Beer, T R M; Wiggenhorn, M; Hawe, A; Kasper, J C; Almeida, A; Quinten, T; Friess, W; Winter, G; Vervaet, C; Remon, J P

2011-02-15

The aim of the present study was to examine the possibilities/advantages of using recently introduced in-line spectroscopic process analyzers (Raman, NIR and plasma emission spectroscopy), within well-designed experiments, for the optimization of a pharmaceutical formulation and its freeze-drying process. The formulation under investigation was a mannitol (crystalline bulking agent)-sucrose (lyo- and cryoprotector) excipient system. The effects of two formulation variables (mannitol/sucrose ratio and amount of NaCl) and three process variables (freezing rate, annealing temperature and secondary drying temperature) upon several critical process and product responses (onset and duration of ice crystallization, onset and duration of mannitol crystallization, duration of primary drying, residual moisture content and amount of mannitol hemi-hydrate in end product) were examined using a design of experiments (DOE) methodology. A 2-level fractional factorial design (2(5-1)=16 experiments+3 center points=19 experiments) was employed. All experiments were monitored in-line using Raman, NIR and plasma emission spectroscopy, which supply continuous process and product information during freeze-drying. Off-line X-ray powder diffraction analysis and Karl-Fisher titration were performed to determine the morphology and residual moisture content of the end product, respectively. In first instance, the results showed that - besides the previous described findings in De Beer et al., Anal. Chem. 81 (2009) 7639-7649 - Raman and NIR spectroscopy are able to monitor the product behavior throughout the complete annealing step during freeze-drying. The DOE approach allowed predicting the optimum combination of process and formulation parameters leading to the desired responses. Applying a mannitol/sucrose ratio of 4, without adding NaCl and processing the formulation without an annealing step, using a freezing rate of 0.9°C/min and a secondary drying temperature of 40°C resulted in efficient freeze-drying supplying end products with a residual moisture content below 2% and a mannitol hemi-hydrate content below 20%. Finally, using Monte Carlo simulations it became possible to determine how varying the factor settings around their optimum still leads to fulfilled response criteria, herewith having an idea about the probability to exceed the acceptable response limits. This multi-dimensional combination and interaction of input variables (factor ranges) leading to acceptable response criteria with an acceptable probability reflects the process design space. Copyright © 2010 Elsevier B.V. All rights reserved.

Dry bulk cargo shipping - An overlooked threat to the marine environment?

PubMed

Grote, Matthias; Mazurek, Nicole; Gräbsch, Carolin; Zeilinger, Jana; Le Floch, Stéphane; Wahrendorf, Dierk-Steffen; Höfer, Thomas

2016-09-15

Approximately 9.5billiontonnes of goods is transported over the world oceans annually with dry bulk representing the largest cargo group. This paper aims to analyse whether the transport and associated inputs of dry bulks into the sea create a risk for the marine environment. For this purpose, we analyse the international regulatory background concerning environmental protection (MARPOL), estimate quantities and identify inputs of such cargoes into the oceans (accidental and operational), and use available information for hazard assessment. Annually, more than 2.15milliontonnes of dry bulk cargoes are likely to enter the oceans, of which 100,000tonnes are potentially harmful to the marine environment according to the definition included in draft maritime regulation. The assessment of the threat to the marine environment is hampered by a lack of available information on chemical composition, bioavailability and toxicity. Perspectives for amendments of the unsatisfying pollution prevention regulations are discussed. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Relationship of Water Content With Silicon and Fluorine Contents of Silicone-Hydrogel Contact Lens Materials.

PubMed

Dupre, Terin E; Benjamin, William J

2018-06-25

The relationship between water (W) content and silicon (Si) content of silicone-hydrogel (SiHy) contact lens materials was inspected using identical methodologies, equipment, and operators for materials composing 16 types of commercially available SiHy contact lenses. Fluorine (F) content was included in the analysis for the three materials also containing a fluoropolymer. One type of lens consisted of a bulk SiHy material coated with thin layers of conventional hydrogel. SiHy materials were obtained in the form of 16 contact lens brands purchased on the open market in a common range of refractive powers from -3 to +6 D in single lots. All test lenses were equilibrated at room temperature in a standard saline recommended in the American National Standards Institute Z80.20-2016 and International Organization for Standardization (ISO) 18369-4:2017 standards. W content was obtained gravimetrically, in %, according to those standards for 16 lenses of each SiHy material. Si content was determined in % using inductively coupled plasma optical emission spectroscopy for four digested lenses of each material. F content was determined in % using an ion-selective electrode for four combusted lenses of each of the three fluorinated SiHy materials. W and Si contents of the bulk SiHy material of the coated lens were estimated by computational exclusion of the hydrogel layers. The linear coefficients of determination (R, n=16) were -0.7576 (relating mean dry Si content [n=4] to mean W content [n=16]) and -0.8819 (relating mean hydrated Si content [n=4] to mean W content [n=16]). When the 4 SiHy materials that were fluorinated or coated were excluded from the analysis, the R values (n=12) were -0.8869 and -0.9263, respectively. When F contents and the coating were added to the assessments, the linear coefficients of determination (R, n=16) became -0.8948 (relating mean dry [Si+F] content to mean W content) and -0.9397 (relating mean hydrated [Si+F] content to mean W content). There is a fundamental negative linear relationship between Si and W contents for SiHy contact lens materials above 35% W content that is followed when F content and hydrogel coatings are empirically added to the analysis below 35% W content. The relationship was tightest for hydrated (Si+F) content and W content, for which the regression equation had an R of -0.9397: (Si+F)=-0.3073 (W)+22.148. The relationship between (Si+F) and W therefore seems to be based on composition rather than structure of available SiHy contact lens materials.

8 CFR 258.2 - Exceptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... longshore work at any United States port under the exceptions provided for in paragraphs (a)(2), (b), or (c... hazardous dry bulk cargo. (i) All tankers qualify for the hazardous cargo exception, including parcel tankers, except for a tanker that has been gas-freed to transport non-hazardous dry bulk commodities. (ii...

Performance of Silica Gel in the Role of Residual Air Drying

NASA Technical Reports Server (NTRS)

Jan, Darrell L.; Hogan, John A.; Koss, Brian; Palmer, Gary H.; Richardson, Justine; Linggi, Paul

2014-01-01

Removal of carbon dioxide (CO2) is a necessary step in air revitalization and is often accomplished with sorbent materials. Since moisture competes with CO2 in sorbent materials, it is necessary to remove the water first. This is typically accomplished in two stages: bulk removal and residual drying. Silica gel is used as the bulk drying material in the Carbon Dioxide Removal Assembly (CDRA) in operation on ISS. There has been some speculation that silica gel may also be capable of serving as the residual drying material. This paper will describe test apparatus and procedures for determining the performance of silica gel in residual air drying.

Sewage sludge drying method combining pressurized electro-osmotic dewatering with subsequent bio-drying.

PubMed

Li, Qian; Lu, Xuebin; Guo, Haigang; Yang, Zengjun; Li, Yingte; Zhi, Suli; Zhang, Keqiang

2018-04-30

In this study, pressurized electro-osmotic dewatering (PEOD) as a pretreatment process, instead of the conventional practice of adding bulking agents, for sewage sludge bio-drying was proposed. Initially, various parameters were optimized for obtaining dewatered sewage sludge (DSS), treated by an efficient, quick, and energy-saving PEOD process. The results show that the moisture content (MC) of sewage sludge could decrease from 83.41% to 60.0% within 7.5 min in the optimum conditions of the PEOD process. Subsequently, two DSS bio-drying tests were carried out to investigate the effects of inoculation. The highest temperature (68.1 °C) was obtained for T2 (inoculation), which was 3.6 °C higher than that for T1 (non- inoculation). The MC accumulative removal rate for T1 (41.49%) was slightly less than that for T2 (44.60%). Lastly, the volatile solid degradation dynamics model parameters were measured. The degradation rate constants (k) for T1 and T2 were 0.00501 and 0.00498, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Production of spray-dried honey jackfruit (Artocarpus heterophyllus) powder from enzymatic liquefied puree.

PubMed

Wong, Chen Wai; Tan, Hong Hock

2017-02-01

This paper presents the enzymatic liquefaction process for honey jackfruit optimized with Pectinex ® Ultra SP-L and Celluclast ® 1.5 L individually or in combinations at different concentrations (0-2.5% v/w) and incubation time (0-2.5 h). Treatment with combinations of enzymes showed a greater effect in the reduction of viscosity (83.9-98.8%) as compared to single enzyme treatment (64.8-87.3%). The best parameter for enzymatic liquefaction was obtained with 1.0% (v/w) Pectinex ® Ultra SP-L and 0.5% (v/w) Celluclast ® 1.5 L for 1.5 h. Spray drying process was carried out using different inlet temperatures (140-180 °C) and maltodextrin concentrations (10-30% w/w). Results indicated that the spray-dried honey jackfruit powder produced at 160 °C with 30% w/w maltodextrin gave the highest product yield (66.90%) with good powder qualities in terms of water activity, solubility, moisture content, hygroscopicity, color and bulk density. The spray-dried honey jackfruit powder could potentially be incorporated into various food products.

Method of altering the effective bulk density of solid material and the resulting product

DOEpatents

Kool, Lawrence B.; Nolen, Robert L.; Solomon, David E.

1983-01-01

A method of adjustably tailoring the effective bulk density of a solid material in which a mixture comprising the solid material, a film-forming polymer and a volatile solvent are sprayed into a drying chamber such that the solvent evaporates and the polymer dries into hollow shells having the solid material captured within the shell walls. Shell density may be varied as a function of solid/polymer concentration, droplet size and drying temperature.

Development and characterization of couscous-like product using bulgur flour as by-product.

PubMed

Yuksel, Ayse Nur; Öner, Mehmet Durdu; Bayram, Mustafa

2017-12-01

Couscous is produced traditionally by agglomeration of Triticum durum semolina with water. The aims of this study were: to produce couscous-like product by substitution of semolina with bulgur by-product (undersize bulgur); to find optimum quantity of bulgur flour and processing conditions. In order to determine the optimum processing parameters and recipes; 0, 25 and 50% of bulgur containing couscous-like samples were prepared. The color, yield, sensory properties, total phenol and flavonoid contents, bulk density, protein and ash content, texture properties were determined. Two different types of dryer e.g. packed bed and microwave were used. Optimum parameters were predicted as 50% of bulgur flour for packed bed (60 °C) and microwave (180 W) drying with 50% (w/w) of water according to yields, color (L*, a*, b*) values and sensory properties (color, odor, general appearance). For packed bed drying at 60 °C yields were 54.28 ± 3.78, 47.70 ± 1.73 and 52.57 ± 7.04% for 0, 25 and 50% bulgur flour containing samples, respectively. Lightness (L*) values of couscous-like samples were decreased with increasing the quantity of bulgur flour after both drying processes. Results of sensory analysis revealed that couscous-like bulgur were more preferable for consumers.

77 FR 44528 - Dry Cargo Residue Discharges in the Great Lakes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-30

...The Coast Guard proposes replacing its existing interim rule with a new rule to regulate the operation of U.S. and foreign vessels carrying bulk dry cargo such as limestone, iron ore, and coal on the U.S. waters of the Great Lakes, and the operation of U.S. bulk dry cargo vessels anywhere on the Great Lakes. Specifically, the Coast Guard proposes new requirements for the discharge of bulk dry cargo residue (DCR) on the U.S. waters of the Great Lakes. The Coast Guard also announces the availability of the tiered Draft Environmental Impact Statement (DEIS) prepared in support of this proposal. The proposed rule would continue to allow non-hazardous and non-toxic discharges of bulk DCR in limited areas of the Great Lakes. However, vessel owners and operators would need to minimize DCR discharges using methods they would be required to document in DCR management plans. The proposed rule would prohibit limestone and clean stone DCR discharges in some waters where they are now permitted. The proposed rule promotes the Coast Guard's strategic goals of maritime mobility and safety and protection of natural resources.

Atmospheric nitrogen deposition in south-east Scotland: Quantification of the organic nitrogen fraction in wet, dry and bulk deposition

NASA Astrophysics Data System (ADS)

González Benítez, Juan M.; Cape, J. Neil; Heal, Mathew R.; van Dijk, Netty; Díez, Alberto Vidal

Water soluble organic nitrogen (WSON) compounds are ubiquitous in precipitation and in the planetary boundary layer, and therefore are a potential source of bioavailable reactive nitrogen. This paper examines weekly rain data over a period of 22 months from June 2005 to March 2007 collected in 2 types of rain collector (bulk deposition and "dry + wet" deposition) located in a semi-rural area 15 km southwest of Edinburgh, UK (N55°51'44″, W3°12'19″). Bulk deposition collectors are denoted in this paper as "standard rain gauges", and they are the design used in the UK national network for monitoring precipitation composition. "Dry + wet" deposition collectors are flushing rain gauges and they are equipped with a rain detector (conductivity array), a spray nozzle, a 2-way valve and two independent bottles to collect funnel washings (dry deposition) and true wet deposition. On average, for the 27 weekly samples with 3 valid replicates for the 2 types of collectors, dissolved organic nitrogen (DON) represented 23% of the total dissolved nitrogen (TDN) in bulk deposition. Dry deposition of particles and gas on the funnel surface, rather than rain, contributed over half of all N-containing species (inorganic and organic). Some discrepancies were found between bulk rain gauges and flushing rain gauges, for deposition of both TDN and DON, suggesting biological conversion and loss of inorganic N in the flushing samplers.

The use of bulk collectors in monitoring wet deposition at high-altitude sites in winter

USGS Publications Warehouse

Ranalli, A.J.; Turk, J.T.; Campbell, D.H.

1997-01-01

Concentrations of dissolved ions from samples collected by wet/dry collectors were compared to those collected by bulk collectors at Halfmoon Creek and Ned Wilson Lake in western Colorado to determine if bulk collectors can be used to monitor wet deposition chemistry in remote, high-altitude regions in winter. Hydrogen-ion concentration was significantly lower (p 0.05) at Halfmoon Creek. Wet deposition concentrations were predicated from bulk deposition concentrations through linear regression analysis. Results indicate that anions (chloride, nitrate and sulfate) can be predicted with a high degree of confidence. Lack of significant differences between seasonal (winter and summer) ratios of bulk to wet deposition concentrations indicates that at sites where operation of a wet/dry collector during the winter is not practical, wet deposition concentrations can be predicted from bulk collector samples through regression analysis of wet and bulk deposition data collected during the summer.

Two-phase olive mill waste composting: enhancement of the composting rate and compost quality by grape stalks addition.

PubMed

Cayuela, Maria Luz; Sánchez-Monedero, Miguel A; Roig, Asunción

2010-06-01

Two-phase olive mill waste (TPOMW) is a semisolid sludge generated by the olive oil industry. Its recycling as a soil amendment, either unprocessed or composted, is being promoted as a beneficial agricultural practice in the Mediterranean area. One of the major difficulties when composting TPOMW is the compaction of the material due to its dough-like texture, which leads to an inadequate aeration. For this reason, the addition of bulking agents is particularly important to attain a proper composting process. In this study we followed the evolution of two composting mixtures (A and B) prepared by mixing equal amounts of TPOMW and sheep litter (SL) (in a dry weight basis). In pile B grape stalks (GS) were added (10% dry weight) as bulking agent to study their effect on the development of the composting process and the final compost quality. The incorporation of grape stalks to the composting mixture changed the organic matter (OM) degradation dynamics and notably reduced the total amount of lixiviates. The evolution of several maturation indices (C/N, germination index, water soluble carbon, humification indices, C/N in the leachates) showed a faster and improved composting process when GS were added. Moreover, chemical (NH4+, NO3(-), cation exchange capacity, macro and micronutrients, heavy metals) and physical properties (bulk and real densities, air content, total water holding capacity, porosity) of the final composts were analysed and confirmed the superior quality of the compost where GS were added.

Effect of surface coating with magnesium stearate via mechanical dry powder coating approach on the aerosol performance of micronized drug powders from dry powder inhalers.

PubMed

Zhou, Qi Tony; Qu, Li; Gengenbach, Thomas; Larson, Ian; Stewart, Peter J; Morton, David A V

2013-03-01

The objective of this study was to investigate the effect of particle surface coating with magnesium stearate on the aerosolization of dry powder inhaler formulations. Micronized salbutamol sulphate as a model drug was dry coated with magnesium stearate using a mechanofusion technique. The coating quality was characterized by X-ray photoelectron spectroscopy. Powder bulk and flow properties were assessed by bulk densities and shear cell measurements. The aerosol performance was studied by laser diffraction and supported by a twin-stage impinger. High degrees of coating coverage were achieved after mechanofusion, as measured by X-ray photoelectron spectroscopy. Concomitant significant increases occurred in powder bulk densities and in aerosol performance after coating. The apparent optimum performance corresponded with using 2% w/w magnesium stearate. In contrast, traditional blending resulted in no significant changes in either bulk or aerosolization behaviour compared to the untreated sample. It is believed that conventional low-shear blending provides insufficient energy levels to expose host micronized particle surfaces from agglomerates and to distribute guest coating material effectively for coating. A simple ultra-high-shear mechanical dry powder coating step was shown as highly effective in producing ultra-thin coatings on micronized powders and to substantially improve the powder aerosolization efficiency.

Solidifying agent and processing of blood used for the larval diet affect screwworm (Diptera: Calliphoridae) life-history parameters.

PubMed

Chaudhury, M F; Skoda, S R; Sagel, A

2011-06-01

Spray-dried whole bovine blood and a sodium polyacrylate polymer gel as a bulking and solidifying agent are among the constituents of the current larval diet for mass rearing screwworm, Cochliomyia hominivorax (Coquerel) (Diptera: Calliphoridae). Locally available, inexpensive dietary materials could reduce rearing cost and address an uncertain commercial supply of spray-dried blood. We compared efficacy of diet prepared from fresh bovine blood after decoagulation with sodium citrate or ethylenediaminetetraacetic acid (EDTA) or after mechanical defibrination, with the diet containing spray-dried blood using either gel or cellulose fiber as the bulking and solidifying agent. Several life-history parameters were compared among insects reared on each of the blood and bulking agent diets combination. Diets containing citrated blood yielded the lightest larval and pupal weights and fewest pupae. EDTA-treated blood with the gel also caused reductions. EDTA-treated blood with fiber yielded screwworms that were heavier and more numerous than those from the diet with citrated blood but lighter than those from the control diet using spray-dried blood. A reduction in percentage of adults emerging from pupae occurred from diets with both bulking agents using citrated blood and the diet using EDTA mixed with the gel bulking agent. As a group, the cellulose-fiber diets performed better than the gel diets. Larval diet did not affect adult longevity, weight of the eggs deposited by the females that emerged or subsequent egg hatch. Parameter measurements of insects from both defibrinated blood diets were similar to those from the spray-dried blood diets, indicating that fresh, defibrinated bovine blood can successfully replace the dry blood in the screwworm rearing medium.

Improvement of flow and bulk density of pharmaceutical powders using surface modification.

PubMed

Jallo, Laila J; Ghoroi, Chinmay; Gurumurthy, Lakxmi; Patel, Utsav; Davé, Rajesh N

2012-02-28

Improvement in flow and bulk density, the two most important properties that determine the ease with which pharmaceutical powders can be handled, stored and processed, is done through surface modification. A limited design of experiment was conducted to establish a standardized dry coating procedure that limits the extent of powder attrition, while providing the most consistent improvement in angle of repose (AOR). The magnetically assisted impaction coating (MAIC) was considered as a model dry-coater for pharmaceutical powders; ibuprofen, acetaminophen, and ascorbic acid. Dry coated drug powders were characterized by AOR, particle size as a function of dispersion pressure, particle size distribution, conditioned bulk density (CBD), Carr index (CI), flow function coefficient (FFC), cohesion coefficient using different instruments, including a shear cell in the Freeman FT4 powder rheometer, and Hansen flowability index. Substantial improvement was observed in all the measured properties after dry coating relative to the uncoated powders, such that each powder moved from a poorer to a better flow classification and showed improved dispersion. The material intrinsic property such as cohesion, plotted as a function of particle size, gave a trend similar to those of bulk flow properties, AOR and CI. Property improvement is also illustrated in a phase map of inverse cohesion (or FFC) as a function of bulk density, which also indicated a significant positive shift due to dry coating. It is hoped that such phase maps are useful in manufacturing decisions regarding the need for dry coating, which will allow moving from wet granulation to roller compaction or to direct compression based formulations. Copyright © 2011 Elsevier B.V. All rights reserved.

Water absorption of freeze-dried meat at different water activities: a multianalytical approach using sorption isotherm, differential scanning calorimetry, and nuclear magnetic resonance.

PubMed

Venturi, Luca; Rocculi, Pietro; Cavani, Claudio; Placucci, Giuseppe; Dalla Rosa, Marco; Cremonini, Mauro A

2007-12-26

Hydration of freeze-dried chicken breast meat was followed in the water activity range of aw=0.12-0.99 by a multianalytical approach comprising of sorption isotherm, differential scanning calorimetry (DSC), and nuclear magnetic resonance (NMR). The amount of frozen water and the shape of the T2-relaxogram were evaluated at each water content by DSC and NMR, respectively. Data revealed an agreement between sorption isotherm and DSC experiments about the onset of bulk water (aw=0.83-0.86), and NMR detected mobile water starting at aw=0.75. The origin of the short-transverse relaxation time part of the meat NMR signal was also reinvestigated through deuteration experiments and proposed to arise from protons belonging to plasticized matrix structures. It is proved both by D2O experiments and by gravimetry that the extra protons not contributing to the water content in the NMR experiments are about 6.4% of the total proton NMR CPMG signal of meat.

Thermal properties of soils: effect of biochar application

NASA Astrophysics Data System (ADS)

Usowicz, Boguslaw; Lukowski, Mateusz; Lipiec, Jerzy

2014-05-01

Thermal properties (thermal conductivity, heat capacity and thermal diffusivity) have a significant effect on the soil surface energy partitioning and resulting in the temperature distribution. Thermal properties of soil depend on water content, bulk density and organic matter content. An important source of organic matter is biochar. Biochar as a material is defined as: "charcoal for application as a soil conditioner". Biochar is generally associated with co-produced end products of pyrolysis. Many different materials are used as biomass feedstock for biochar, including wood, crop residues and manures. Additional predictions were done for terra preta soil (also known as "Amazonian dark earth"), high in charcoal content, due to adding a mixture of charcoal, bone, and manure for thousands of years i.e. approximately 10-1,000 times longer than residence times of most soil organic matter. The effect of biochar obtained from the wood biomass and other organic amendments (peat, compost) on soil thermal properties is presented in this paper. The results were compared with wetland soils of different organic matter content. The measurements of the thermal properties at various water contents were performed after incubation, under laboratory conditions using KD2Pro, Decagon Devices. The measured data were compared with predictions made using Usowicz statistical-physical model (Usowicz et al., 2006) for biochar, mineral soil and soil with addition of biochar at various water contents and bulk densities. The model operates statistically by probability of occurrence of contacts between particular fractional compounds. It combines physical properties, specific to particular compounds, into one apparent conductance specific to the mixture. The results revealed that addition of the biochar and other organic amendments into the soil caused considerable reduction of the thermal conductivity and diffusivity. The mineral soil showed the highest thermal conductivity and diffusivity that decreased in soil with addition of biochar and pure biochar. The reduction of both properties was mostly due to decrease in both particle density and bulk density. Both biochar and the organic amendments addition resulted in a decrease of the heat capacity of the mixtures in dry state and considerable increase in wet state. The lowest and highest reduction in the thermal conductivity with decreasing water content was obtained for pure biochar and mineral soil, respectively. The thermal diffusivity had a characteristic maximum at higher bulk densities and lower water contents. The wetland soil higher in organic matter content exhibit smaller temporal variation of the thermal properties compared to soils lower in organic matter content in response to changes of water content. The statistical-physical model was found to be useful for satisfactory predicting thermal properties of the soil with addition of biochar and organic amendments. Usowicz B. et al., 2006. Thermal conductivity modelling of terrestrial soil media - A comparative study. Planetary and Space Science 54, 1086-1095.

7 CFR 58.250 - Dry whole milk.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Dry whole milk. 58.250 Section 58.250 Agriculture... Products Bearing Usda Official Identification § 58.250 Dry whole milk. Dry whole milk in commercial bulk... Grades of Dry Whole Milk. Quality requirements for dry whole milk in consumer packages shall be for U.S...

Manufacturing Solid Dosage Forms from Bulk Liquids Using the Fluid-bed Drying Technology.

PubMed

Qi, Jianping; Lu, Y I; Wu, Wei

2015-01-01

Solid dosage forms are better than liquid dosage forms in many ways, such as improved physical and chemical stability, ease of storage and transportation, improved handling properties, and patient compliance. Therefore, it is required to transform dosage forms of liquid origins into solid dosage forms. The functional approaches are to absorb the liquids by solid excipients or through drying. The conventional drying technologies for this purpose include drying by heating, vacuum-, freeze- and spray-drying, etc. Among these drying technologies, fluidbed drying emerges as a new technology that possesses unique advantages. Fluid-bed drying or coating is highly efficient in solvent removal, can be performed at relatively low temperatures, and is a one-step process to manufacture formulations in pellet forms. In this article, the status of the art of manufacturing solid dosage forms from bulk liquids by fluid-bed drying technology was reviewed emphasizing on its application in solid dispersion, inclusion complexes, self-microemulsifying systems, and various nanoscale drug delivery systems.

7 CFR 58.250 - Dry whole milk.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Requirements for Finished Products Bearing Usda Official Identification § 58.250 Dry whole milk. Dry whole milk in commercial bulk...

[Study on nano-CaCO3 applicated in Xin Yue Shu Capsules preliminarily].

PubMed

Jiang, Yan-Rong; Zhang, Zhen-Hai; Cui, Li; He, Jun-Jie; Hu, Shao-Ying; Jia, Xiao-Bin

2012-11-01

To investigate the characteristics of nano-CaCO3 applicated in Xin Yue Shu Capsules. Studied the effect of different dosages of aerosil or nano-CaCO3 on fluidity, bulk density, moisture absorption of Xin Yue Shu capsules spray drying powder. In vitro dissolution and ferulic acid stability of Xin Yue Shu capsules was observed. It significantly improved powder fluidity and bulk density of Xin Yue Shu spray drying powder when aerosil or nano-CaCO3 was added. But there was no significant effect on powder moisture absorption, ferulic acid in vitro dissolution and ferulic acid stability. The effect of Nano-CaCO3 on improving powder fluidity and bulk density applicated in the spray drying powder of traditional Chinese medicine deserves studying further.

1.2.1.1 Harvest, Collection and Storage Quarter 3 Milestone Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendt, Lynn M.; Smith, William A.; Cafferty, Kara G.

Single pass baling of corn stover is required in order to meet targets for the herbaceous biomass 2017 logistics design case. Single-pass pass stover harvest is based on the grain harvest and generally results in stover with a moisture content of 30-50% wet basis (w.b). Aerobic storage of corn stover with high moisture results in high levels of dry matter loss (DML), up to 25%. Anaerobic storage (ensiling) reduces DML to less than 5%, but additional costs are associated with handling and transporting the extra moisture in the biomass. This milestone provides a best-estimate of costs for using high moisturemore » feedstock within the conventional baled logistics system. The costs of three (3) anaerobic storage systems that reduce dry matter losses (bale wrap, silage tube, and silage drive over pile) are detailed in this milestone and compared to both a conventional dry-baled corn stover case and a high moisture bale case, both stored aerobically. The total logistics cost (harvest, collection, storage, and transportation) of the scenarios are as follows: the conventional multi-pass dry bale case and the single-pass high moisture case stored aerobically were nearly equivalent at $61.15 and $61.24/DMT. The single-pass bale wrap case was the lowest at $57.63/DMT. The bulk anaerobic cases were the most expensive at $84.33 for the silage tube case and $75.97 for the drive over pile, which reflect the additional expense of transporting high-moisture bulk material; however, a reduction in preprocessing costs may occur because these feedstocks are size reduced in the field. In summary, the costs estimates presented in this milestone report can be used to determine if anaerobic storage of high-moisture corn stover is an economical option for dry matter preservation.« less

Basic and Morphological Properties of Bukit Goh Bauxite

NASA Astrophysics Data System (ADS)

Hasan, Muzamir; Nor Azmi, Ahmad Amirul Faez Ahmad; Tam, Weng Long; Phang, Biao Yu; Azizul Moqsud, M.

2018-03-01

Investigation conducted by International Maritime Organization (IMO) concluded that the loss of the Bulk Jupiter that carrying bauxite from Kuantan has uncovered evidence to suggest liquefaction led to loss of stability. This research analysed Bukit Goh bauxite and comparison was made with International Maritime Solid Bulk Cargoes (IMSBC Code) standard. To analyse these characteristics of the bauxite, four samples were selected at Bukit Goh, Kuantan ; two of the samples from the Bukit Goh mine and two samples from the stock piles were tested to identify the bauxite basic and morphological properties by referring to GEOSPEC 3 : Model Specification for Soil Testing ; particle size distribution, moisture content and specific gravity and its morphological properties. Laboratory tests involved including Hydrometer test, Small Pycnometer test, Dry Sieve test and Field Emission Scanning Electron Microscop (FESEM) test. The results show that the average moisture content of raw Bukit Goh bauxite is 20.64% which exceeded the recomended value of maximum 10%. Average fine material for raw bauxite is 37.75% which should not be greater than 30% per IMSBC standard. By that, the bauxite from Bukit Goh mine do not achieved the minimum requirements and standards of the IMSBC standard and need to undergo beneficiation process for better quality and safety.

Physicochemical properties and carbon density of alpine sod layer with their variation across habitat gradients in the Zoige Plateau

NASA Astrophysics Data System (ADS)

Peixi, Su; Zijuan, Zhou; Rui, Shi; tingting, Xie

2017-04-01

The alpine sod layer is a soft, tough and resistant to shifting surface soil layer under the formation of the natural vegetation in the plateau cold region, understanding its ecological function is a prerequisite to promote grass and animal husbandry production for recuperation and protection, and the active use of project construction. Based on the extensive investigation on the alpine vegetation of the Zoige Plateau in the Eastern Qinghai-Tibetan Plateau of China, set up moisture gradient community sample plots: swamp, degraded swamp, swampy meadow, wet meadow, dry meadow and degraded meadow, and the elevation gradient community sample plots: subalpine meadow, subalpine shrub meadow, alpine shrub meadow and alpine meadow were set up. The sod layer bulk density, soil particle composition and soil organic carbon (SOC) content of different types of community plots were analyzed and to compare its carbon sequestration capacity on the moisture and elevation gradients. The results showed that the average thickness of the sod layer was 30 cm, the bulk density of the swamp was the smallest, and the SOC content was above 300 g/kg. The bulk density of degraded meadow was the highest while its SOC content was decreased significantly. The SOC density of sod layer in different communities was between 10 and 24 kg C/m2, and decreased with the decreasing of soil water availability, and meadow degradation significantly decreased the soil organic carbon storage in sod layer. The sod layer SOC density of alpine shrub meadow was 15% higher than that of meadow on the altitudinal gradient. It was concluded that the mass water content threshold value for maintaining the sod layer stable is 30%. In the degraded succession of alpine vegetation from swamp to meadow, the bulk density and compactness of sod layer became larger, while the organic carbon content, carbon density and carbon storage decreased. The higher the gravel content of swamp, the more easily degraded, and the higher the sand content of the meadow, the more easily degraded. Shrub meadow had higher carbon sequestration capacity than that of meadow, but the productive function of shrub meadow was lower. Keeping the sustainable development of grassland productivity and maintaining the carbon sequestration ecological function, it is necessary to prevent the degradation of the sod layer, and restrain the succession from meadow to scrub meadow. Key Words: surface soil layer, soil organic carbon, carbon density, alpine vegetation, Zoige Plateau

A coupled melt-freeze temperature index approach in a one-layer model to predict bulk volumetric liquid water content dynamics in snow

NASA Astrophysics Data System (ADS)

Avanzi, Francesco; Yamaguchi, Satoru; Hirashima, Hiroyuki; De Michele, Carlo

2016-04-01

Liquid water in snow rules runoff dynamics and wet snow avalanches release. Moreover, it affects snow viscosity and snow albedo. As a result, measuring and modeling liquid water dynamics in snow have important implications for many scientific applications. However, measurements are usually challenging, while modeling is difficult due to an overlap of mechanical, thermal and hydraulic processes. Here, we evaluate the use of a simple one-layer one-dimensional model to predict hourly time-series of bulk volumetric liquid water content in seasonal snow. The model considers both a simple temperature-index approach (melt only) and a coupled melt-freeze temperature-index approach that is able to reconstruct melt-freeze dynamics. Performance of this approach is evaluated at three sites in Japan. These sites (Nagaoka, Shinjo and Sapporo) present multi-year time-series of snow and meteorological data, vertical profiles of snow physical properties and snow melt lysimeters data. These data-sets are an interesting opportunity to test this application in different climatic conditions, as sites span a wide latitudinal range and are subjected to different snow conditions during the season. When melt-freeze dynamics are included in the model, results show that median absolute differences between observations and predictions of bulk volumetric liquid water content are consistently lower than 1 vol%. Moreover, the model is able to predict an observed dry condition of the snowpack in 80% of observed cases at a non-calibration site, where parameters from calibration sites are transferred. Overall, the analysis show that a coupled melt-freeze temperature-index approach may be a valid solution to predict average wetness conditions of a snow cover at local scale.

Measurements of size-fractionated concentration and bulk dry deposition of atmospheric particulate bound mercury

NASA Astrophysics Data System (ADS)

Fang, G. C.; Zhang, L.; Huang, C. S.

2012-12-01

Daily samples of size-fractionated (18, 10, 2.5 and 1.0 μm) particulate-bound mercury Hg(p) were collected using Micro-Orifice Uniform Deposition Impactors (MOUDI), on randomly selected days each month between November 2010 and July 2011, at a traffic site (Hungkuang), a wetland site (Gaomei), and an industrial site (Quanxing) in central Taiwan. Bulk dry deposition was also collected simultaneously using a surrogate surface. The nine-month average (±standard deviation) Hg(p) concentrations were 0.57 (±0.90), 0.17 (±0.27), and 0.94 (±0.92) ng m-3 at Hungkuang, Gaomei, and Quanxing, respectively. Concentrations in November and December were much higher than in the other months due to a combination of high local emissions and meteorological conditions. PM1.0 contributed more than 50% to the bulk concentration at the traffic and the industrial sites, but only contributed 25% at the wetland site. PM1.0-2.5 contributed 25%-50%, depending on location, to the bulk mass. Coarse fraction (PM2.5-18) contributed 7% at Hungkuang, 25% at Gaomei, and 19% at Quanxing. Samples with very high bulk concentrations had large fine fractions. Annual dry deposition estimated from the surrogate surface measurements was in the range of 30-85 μg m-2 yr-1 at the three sites. Coarse particulate Hg(p) were estimated to contribute 50-85% of the total Hg(p) dry deposition. Daily dry deposition velocities (Vd) ranged from 0.01 to 7.7 cm s-1. The annual Vd generated from the total measured fluxes was 0.34, 0.60 and 0.29 cm s-1 at Hungkuang, Gaomei, and Quanxing, respectively. These values can be reasonably reproduced using a size-resolved model and measured size fractions.

Evaluation of specimen preparation techniques for micro-PIXE localisation of elements in hyperaccumulating plants

NASA Astrophysics Data System (ADS)

Kachenko, Anthony G.; Siegele, Rainer; Bhatia, Naveen P.; Singh, Balwant; Ionescu, Mihail

2008-04-01

Hybanthus floribundus subsp. floribundus, a rare Australian Ni-hyperaccumulating shrub and Pityrogramma calomelanos var. austroamericana, an Australian naturalized As-hyperaccumulating fern are promising species for use in phytoremediation of contaminated sites. Micro-proton-induced X-ray emission (μ-PIXE) spectroscopy was used to map the elemental distribution of the accumulated metal(loid)s, Ca and K in leaf or pinnule tissues of the two plant species. Samples were prepared by two contrasting specimen preparation techniques: freeze-substitution in tetrahydrofuran (THF) and freeze-drying. The specimens were analysed to compare the suitability of each technique in preserving (i) the spatial elemental distribution and (ii) the tissue structure of the specimens. Further, the μ-PIXE results were compared with concentration of elements in the bulk tissue obtained by ICP-AES analysis. In H. floribundus subsp. floribundus, μ-PIXE analysis revealed Ni, Ca and K concentrations in freeze-dried leaf tissues were at par with bulk tissue concentrations. Elemental distribution maps illustrated that Ni was preferentially localised in the adaxial epidermal tissues (1% DW) and least concentration was found in spongy mesophyll tissues (0.53% DW). Conversely, elemental distribution maps of THF freeze-substituted tissues indicated significantly lower Ni, Ca and K concentrations than freeze-dried specimens and bulk tissue concentrations. Moreover, Ni concentrations were uniform across the whole specimen and no localisation was observed. In P. calomelanos var. austroamericana freeze-dried pinnule tissues, μ-PIXE revealed statistically similar As, Ca and K concentrations as compared to bulk tissue concentrations. Elemental distribution maps showed that As localisation was relatively uniform across the whole specimen. Once again, THF freeze-substituted tissues revealed a significant loss of As compared to freeze-dried specimens and the concentrations obtained by bulk tissue analysis. The results demonstrate that freeze-drying is a suitable sample preparation technique to study elemental distribution of ions in H. floribundus and P. calomelanos plant tissues using μ-PIXE spectroscopy. Furthermore, cellular structure was preserved in samples prepared using this technique.

Relative intranuclear magnesium and phosphorus contents in normal and tumor cells of the human thyroid gland as revealed by energy-dispersive X-ray microanalysis.

PubMed

Lukács, G L; Zs-Nagy, I; Steiber, J; Györi, F; Balázs, G

1996-01-01

Energy dispersive X-ray microanalysis was performed on altogether 42 surgically removed tissue specimens of 32 patients, which were taken either from intact thyroid parts or various histopathologically verified tumors of the thyroid gland. The tissue specimens were processed with the freeze-fracture-freeze-drying technique and then analyzed in the so-called bulk specimen form. The studies were carried out during the years 1980-81, when intranuclear monovalent ionic composition was studied in detail. From the retained total elemental peak list, it was possible to calculate retrospectively the relative intranuclear Mg and P contents. The data processed by nested (hierarchical) analysis of variance show that the intranuclear Mg content of the 5 diagnostic groups (normal thyroid tissue, thyroiditis, benign adenomas, differentiated carcinomas and undifferentiated thyroid tumors) increases significantly, in parallel with the increasing malignancy, but the P content remains unchanged. One can conclude that the elevated intranuclear Mg content in the tumors of high malignancy may be of diagnostic importance, and a warning signal for the therapeutic approaches based on Mg-supplementations.

Spent coffee ground as a new bulking agent for accelerated biodrying of dewatered sludge.

PubMed

Hao, Zongdi; Yang, Benqin; Jahng, Deokjin

2018-07-01

The feasibility of using spent coffee ground (SCG) as a new bulking agent for biodrying of dewatered sludge (DS) was investigated in comparison with two other frequently-used bulking agents, air-dried sludge (AS) and sawdust (SD). Results showed that the moisture contents (MC) of 16-day DS biodrying with AS (Trial A), SCG (Trial B) and SD (Trial C) decreased from 70.14 wt%, 68.25 wt% and 71.63 wt% to 59.12 wt%, 41.35 wt% and 57.69 wt%, respectively. In case of Trial B, the MC rapidly decreased to 46.16 wt% with the highest water removal (70.87%) within 8 days because of the longest high-temperature period (5.8 days). Further studies indicated that the abundant biodegradable volatile solids (BVS) and high dissolved organic matter (DOM) contents in SCG were the main driving forces for water removal. According to pyrosequencing data, Firmicutes, most of which were recognized as thermophiles, was rapidly enriched on Day 8 and became the dominant phylum in Trial B. Four thermophilic genera, Bacillus, Ureibacillus, Geobacillus and Thermobifida, which can produce thermostable hydrolytic extracellular enzymes, were the most abundant in Trial B, indicating that these thermophilic bacteria evolved during the long high-temperature period enhanced the biodegradation of BVS in SCG. The 8-day biodried product of Trial B was demonstrated to be an excellent solid fuel with low heating value (LHV) of 9284 kJ kg -1 , which was 2.1 and 1.8 times those of biodried products with AS and SD, respectively. Thus SCG was found to be an excellent bulking agent accelerating DS biodrying and producing a solid fuel with a high calorific value. Copyright © 2018 Elsevier Ltd. All rights reserved.

Influence of deposition and spray pattern of nasal powders on insulin bioavailability.

PubMed

Pringels, E; Callens, C; Vervaet, C; Dumont, F; Slegers, G; Foreman, P; Remon, J P

2006-03-09

The influence of the deposition pattern and spray characteristics of nasal powder formulations on the insulin bioavailability was investigated in rabbits. The formulations were prepared by freeze drying a dispersion containing a physical mixture of drum dried waxy maize starch (DDWM)/Carbopol 974P (90/10, w/w) or a spray-dried mixture of Amioca starch/Carbopol 974P (25/75, w/w). The deposition in the nasal cavity of rabbits and in a silicone human nose model after actuation of three nasal delivery devices (Monopowder, Pfeiffer and experimental system) was compared and related to the insulin bioavailability. Posterior deposition of the powder formulation in the nasal cavity lowered the insulin bioavailability. To study the spray pattern, the shape and cross-section of the emitted powder cloud were analysed. It was concluded that the powder bulk density of the formulation influenced the spray pattern. Consequently, powders of different bulk density were prepared by changing the solid fraction of the freeze dried dispersion and by changing the freezing rate during freeze drying. After nasal delivery of these powder formulations no influence of the powder bulk density and of the spray pattern on the insulin bioavailability was observed.

Microencapsulation of Nigella sativa oleoresin by spray drying for food and nutraceutical applications.

PubMed

Edris, Amr E; Kalemba, Danuta; Adamiec, Janusz; Piątkowski, Marcin

2016-08-01

Oleoresin of Nigella sativa L. (Black cumin) was obtained from the seeds using hexane extraction at room temperature. The oleoresin was emulsified in an aqueous solution containing gum Arabic/maltodextrin (1:1 w/w) and then encapsulated in powder form by spray drying. The characteristics of the obtained powder including moisture content, bulk density, wettability, morphology, encapsulation efficiency were evaluated. The effect of the spray drying on the chemical composition of the volatile oil fraction of N. sativa oleoresin was also evaluated using gas chromatographic-mass spectroscopic analysis. Results indicated that the encapsulation efficiency of the whole oleoresin in the powder can range from 84.2±1.5% to 96.2±0.2% depending on the conditions of extracting the surface oil from the powder. On the other hand the encapsulation efficiency of the volatile oil fraction was 86.2% ±4.7. The formulated N. sativa L. oleoresin powder can be used in the fortification of processed food and nutraceuticals. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microstructural and bulk property changes in hardened cement paste during the first drying process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maruyama, Ippei, E-mail: ippei@dali.nuac.nagoya-u.ac.jp; Nishioka, Yukiko; Igarashi, Go

2014-04-01

This paper reports the microstructural changes and resultant bulk physical property changes in hardened cement paste (hcp) during the first desorption process. The microstructural changes and solid-phase changes were evaluated by water vapor sorption, nitrogen sorption, ultrasonic velocity, and {sup 29}Si and {sup 27}Al nuclear magnetic resonance. Strength, Young's modulus, and drying shrinkage were also examined. The first drying process increased the volume of macropores and decreased the volume of mesopores and interlayer spaces. Furthermore, in the first drying process globule clusters were interconnected. During the first desorption, the strength increased for samples cured at 100% to 90% RH, decreasedmore » for 90% to 40% RH, and increased again for 40% to 11% RH. This behavior is explained by both microstructural changes in hcp and C–S–H globule densification. The drying shrinkage strains during rapid drying and slow drying were compared and the effects of the microstructural changes and evaporation were separated.« less

Application of Moldavian dragonhead (Dracocephalum moldavica L.) leaves addition as a functional component of nutritionally valuable corn snacks.

PubMed

Wójtowicz, Agnieszka; Oniszczuk, Anna; Oniszczuk, Tomasz; Kocira, Sławomir; Wojtunik, Karolina; Mitrus, Marcin; Kocira, Anna; Widelski, Jarosław; Skalicka-Woźniak, Krystyna

2017-09-01

Application of Moldavian dragonhead ( Dracocephalum moldavica L.) leaves in extruded snacks was evaluated. Directly expanded corn snacks (crisps) were supplemented with 5-20% of dragonhead leaves. The supplemented snacks were characterized to have improved nutritional value and were a good source of dietary fibre. The presence of phenolic compounds, especially rosmarinic acid, showed a high antioxidant potential and a radical scavenging activity of tested snacks, especially if a high content of additive was used. The increasing amount of additive also had an impact on the physical properties of extrudates lowering the expansion ratio, water absorption and solubility, yet increasing bulk density, cutting force and the breaking index of the enriched snacks. The highest viscosity was observed at 5 and 10% addition level. The increasing amount of dragonhead leaves lowered the brightness of snacks and increased the greenness tint significantly. A sensory evaluation showed good acceptability of snacks enriched with up to 15% of dragonhead dried leaves. Dried leaves of the Moldavian dragonhead seem to be a prospective functional additive for extruded crisps with a high nutritional value, especially because of dietary fibre and rosmarinic acid content, a strong antioxidant potential and acceptable sensory properties.

Arbuscular Mycorrhiza Alleviates Restrictions to Substrate Water Flow and Delays Transpiration Limitation to Stronger Drought in Tomato.

PubMed

Bitterlich, Michael; Sandmann, Martin; Graefe, Jan

2018-01-01

Arbuscular mycorrhizal fungi (AMF) proliferate in soil pores, on the surface of soil particles and affect soil structure. Although modifications in substrate moisture retention depend on structure and could influence plant water extraction, mycorrhizal impacts on water retention and hydraulic conductivity were rarely quantified. Hence, we asked whether inoculation with AMF affects substrate water retention, water transport properties and at which drought intensity those factors become limiting for plant transpiration. Solanum lycopersicum plants were set up in the glasshouse, inoculated or not with Funneliformis mosseae , and grown for 35 days under ample water supply. After mycorrhizal establishment, we harvested three sets of plants, one before (36 days after inoculation) and the second (day 42) and third (day 47) within a sequential drying episode. Sampling cores were introduced into pots before planting. After harvest, moisture retention and substrate conductivity properties were assessed and water retention and hydraulic conductivity models were fitted. A root water uptake model was adopted in order to identify the critical substrate moisture that induces soil derived transpiration limitation. Neither substrate porosity nor saturated water contents were affected by inoculation, but both declined after substrates dried. Drying also caused a decline in pot water capacity and hydraulic conductivity. Plant available water contents under wet (pF 1.8-4.2) and dry (pF 2.5-4.2) conditions increased in mycorrhizal substrates and were conserved after drying. Substrate hydraulic conductivity was higher in mycorrhizal pots before and during drought exposure. After withholding water from pots, higher substrate drying rates and lower substrate water potentials were found in mycorrhizal substrates. Mycorrhiza neither affected leaf area nor root weight or length. Consistently with higher substrate drying rates, AMF restored the plant hydraulic status, and increased plant transpiration when soil moisture declined. The water potential at the root surface and the resistance to water flow in the rhizosphere were restored in mycorrhizal pots although the bulk substrate dried more. Finally, substrates colonized by AMF can be more desiccated before substrate water flux quantitatively limits transpiration. This is most pronounced under high transpiration demands and complies with a difference of over 1,000 hPa in substrate water potential.

The Impact of Rhizosphere Processes on Water Flow and Root Water Uptake

NASA Astrophysics Data System (ADS)

Schwartz, Nimrod; Kroener, Eva; Carminati, Andrea; Javaux, Mathieu

2015-04-01

For many years, the rhizosphere, which is the zone of soil in the vicinity of the roots and which is influenced by the roots, is known as a unique soil environment with different physical, biological and chemical properties than those of the bulk soil. Indeed, in recent studies it has been shown that root exudate and especially mucilage alter the hydraulic properties of the soil, and that drying and wetting cycles of mucilage result in non-equilibrium water dynamics in the rhizosphere. While there are experimental evidences and simplified 1D model for those concepts, an integrated model that considers rhizosphere processes with a detailed model for water and roots flow is absent. Therefore, the objective of this work is to develop a 3D physical model of water flow in the soil-plant continuum that take in consideration root architecture and rhizosphere specific properties. Ultimately, this model will enhance our understanding on the impact of processes occurring in the rhizosphere on water flow and root water uptake. To achieve this objective, we coupled R-SWMS, a detailed 3D model for water flow in soil and root system (Javaux et al 2008), with the rhizosphere model developed by Kroener et al (2014). In the new Rhizo-RSWMS model the rhizosphere hydraulic properties differ from those of the bulk soil, and non-equilibrium dynamics between the rhizosphere water content and pressure head is also considered. We simulated a wetting scenario. The soil was initially dry and it was wetted from the top at a constant flow rate. The model predicts that, after infiltration the water content in the rhizosphere remained lower than in the bulk soil (non-equilibrium), but over time water infiltrated into the rhizosphere and eventually the water content in the rhizosphere became higher than in the bulk soil. These results are in qualitative agreement with the available experimental data on water dynamics in the rhizosphere. Additionally, the results show that rhizosphere processes affect the spatial distribution of root water uptake. This suggests that rhizosphere processes effect root water uptake at the plant scale. Overall, these preliminary results demonstrate the impact of rhizosphere on water flow and root water uptake, and the ability of the Rhizo-RSWMS to simulate these processes. References Javaux, M., Schröder, T., Vanderborght, J., & Vereecken, H. (2008). Use of a three-dimensional detailed modeling approach for predicting root water uptake. Vadose Zone Journal, 7(3), 1079-1088.‏ Kroener, E., Zarebanadkouki, M., Kaestner, A., & Carminati, A. (2014). Nonequilibrium water dynamics in the rhizosphere: How mucilage affects water flow in soils. Water Resources Research, 50(8), 6479-6495.‏

Estimation of Dry Fracture Weakness, Porosity, and Fluid Modulus Using Observable Seismic Reflection Data in a Gas-Bearing Reservoir

NASA Astrophysics Data System (ADS)

Chen, Huaizhen; Zhang, Guangzhi

2017-05-01

Fracture detection and fluid identification are important tasks for a fractured reservoir characterization. Our goal is to demonstrate a direct approach to utilize azimuthal seismic data to estimate fluid bulk modulus, porosity, and dry fracture weaknesses, which decreases the uncertainty of fluid identification. Combining Gassmann's (Vier. der Natur. Gesellschaft Zürich 96:1-23, 1951) equations and linear-slip model, we first establish new simplified expressions of stiffness parameters for a gas-bearing saturated fractured rock with low porosity and small fracture density, and then we derive a novel PP-wave reflection coefficient in terms of dry background rock properties (P-wave and S-wave moduli, and density), fracture (dry fracture weaknesses), porosity, and fluid (fluid bulk modulus). A Bayesian Markov chain Monte Carlo nonlinear inversion method is proposed to estimate fluid bulk modulus, porosity, and fracture weaknesses directly from azimuthal seismic data. The inversion method yields reasonable estimates in the case of synthetic data containing a moderate noise and stable results on real data.

Drying effects on the antioxidant properties of tomatoes and ginger.

PubMed

Gümüşay, Özlem Aktürk; Borazan, Alev Akpınar; Ercal, Nuran; Demirkol, Omca

2015-04-15

In this study, the effects of four different drying processes, sun drying (SD), oven drying (OD), vacuum oven drying (VOD) and freeze drying (FD) for tomatoes (Solanum lycopersicum) and ginger (Zingiber officinale) in terms of thiolic and phenolic contents have been studied. Thiol content, total phenolic content (TPC), ascorbic acid (AA) content, and cupric ion reducing antioxidant capacity (CUPRAC) were determined in fresh and dried samples. Glutathione (GSH) and cysteine (Cys) were determined as the thiol contents of tomatoes and ginger. Significant losses were observed in the contents of TPC, AA, GSH and Cys and CUPRAC values in all samples that were dried using the thermal method. There was a statistically significant difference in the losses of the TPC, AA, and thiol contents between the use of thermal drying and freeze drying (except Cys in tomatoes) methods. Freeze dried tomato and ginger samples have been found to have better antioxidant properties. Copyright © 2014 Elsevier Ltd. All rights reserved.

48 CFR 47.501 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of bulk liquid cargoes such as liquid petroleum products, vegetable oils, and molasses. U.S.-flag... cargoes of dry bulk items or, when carried in deep tanks, bulk liquids such as petroleum and vegetable oils. Foreign-flag vessel means any vessel of foreign registry including vessels owned by U.S. citizens...

48 CFR 47.501 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of bulk liquid cargoes such as liquid petroleum products, vegetable oils, and molasses. U.S.-flag... cargoes of dry bulk items or, when carried in deep tanks, bulk liquids such as petroleum and vegetable oils. Foreign-flag vessel means any vessel of foreign registry including vessels owned by U.S. citizens...

Soil compaction related to grazing and its effects on herbaceous roots frequency and soil organic matter content in rangelands of SW Spain

NASA Astrophysics Data System (ADS)

Pulido, Manuel; Schnabel, Susanne; Francisco Lavado Contador, Joaquín; Miralles Mellado, Isabel

2016-04-01

Rangelands in SW Spain occupy a total surface area of approximately 6 million ha and constitute the most representative extensive ranching system of the Iberian Peninsula gathering more than 13 million livestock heads. They are characterised by an herbaceous layer, mostly composed of therophytic species, with a disperse tree cover, mainly holm oak and cork oak (Quercus ilex rotundifolia and Q. suber), interspersed with shrubs in many places. This type of land system is of ancient origin and experienced frequent changes in land use in the past, since agricultural, livestock and forestry activities have coexisted within the same farms. In recent decades, livestock farming has become dominant due, in part, to the subsidies of the Common Agriculture Policy. Since Spain joined the European Union in 1986 until the year 2000, the number of domestic animals doubled, particularly cattle, and consequently animal stocking rates have increased on average from 0.40 AU ha-1 up to 0.70 AU ha-1. This increase in animal stocking rates, along with a progressive substitution of cattle instead of sheep in many farms, has led to the occurrence of land degradation processes such as the reduction of grass cover or soil compaction in heavily grazed areas. Previous research has evidenced higher values of soil bulk density and resistance to penetration as well as larger bare surface areas in spring in fenced areas with animal stocking rates above 1 AU ha-1. However, a better understanding of how increasing bulk density or resistance to penetration influence the frequency of herbaceous roots and how a reduction in the frequency of roots affects soil organic matter content in rangelands is still unknown. Therefore, the main goal of this study was to determine possible relationships between the frequencies of herbaceous roots and soil organic matter content in order to understand the effect of excessive animal numbers on the depletion of soil fertility by reducing progressively the quantity of roots. The study was carried out in 22 fenced areas belonging to 10 privately-owned farms grazed under different intensities (range: 0.19 - 15.76 AU ha-1 year-1). A total number of 597 undisturbed core samples and 311 bulk samples were collected in order to determine bulk density and soil organic matter content, among other many properties. Resistance to soil penetration was quantified using Eijkelkamp Penetrologger in 890 random points at different depth (0-80 cm) and soil moisture content (dry and wet). The frequency of herbaceous roots was estimated for each soil horizon in 47 soil profiles, described according to FAO and categorized in 4 classes: none-few, common, abundant and many. All variables were pair-wise correlated and their mean values were compared between the different classes of root frequency. Results showed an inverse relationship between soil resistance to penetration and the frequency of herbaceous roots, i.e. the amount of roots lower in soils with high resistance to penetration. Soil horizons with none or few, common, abundant and many roots averaged 0.74%, 1.27%, 2.23% and 2.70% of SOM, respectively, showing significant differences between groups. Furthermore, SOM showed negative coefficients of correlation with resistance to penetration under dry (r=-0.34, p<0.05) and under wet conditions (r=-0.11, p<0.05) and bulk density (r=-0.31, p<0.05). The values herein observed confirm that soil compaction provoked by an excessive number of animals can decrease the content of soil organic matter by reducing the quantity of herbaceous roots although further research is still needed.

Climate and the collapse of Maya civilization.

PubMed

Haug, Gerald H; Günther, Detlef; Peterson, Larry C; Sigman, Daniel M; Hughen, Konrad A; Aeschlimann, Beat

2003-03-14

In the anoxic Cariaco Basin of the southern Caribbean, the bulk titanium content of undisturbed sediment reflects variations in riverine input and the hydrological cycle over northern tropical South America. A seasonally resolved record of titanium shows that the collapse of Maya civilization in the Terminal Classic Period occurred during an extended regional dry period, punctuated by more intense multiyear droughts centered at approximately 810, 860, and 910 A.D. These new data suggest that a century-scale decline in rainfall put a general strain on resources in the region, which was then exacerbated by abrupt drought events, contributing to the social stresses that led to the Maya demise.

Surface-Sensitive and Bulk Studies on the Complexation and Photosensitized Degradation of Catechol by Iron(III) as a Model for Multicomponent Aerosol Systems

NASA Astrophysics Data System (ADS)

Al-abadleh, H. A.; Tofan-Lazar, J.; Situm, A.; Ruffolo, J.; Slikboer, S.

2013-12-01

Surface water plays a crucial role in facilitating or inhibiting surface reactions in atmospheric aerosols. Little is known about the role of surface water in the complexation of organic molecules to transition metals in multicomponent aerosol systems. We will show results from real time diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) experiments for the in situ complexation of catechol to Fe(III) and its photosensitized degradation under dry and humid conditions. Catechol was chosen as a simple model for humic-like substances (HULIS) in aerosols and aged polyaromatic hydrocarbons (PAH). It has also been detected in secondary organic aerosols (SOA) formed from the reaction of hydroxyl radicals with benzene. Given the importance of the iron content in aerosols and its biogeochemistry, our studies were conducted using FeCl3. For comparison, these surface-sensitive studies were complemented with bulk aqueous ATR-FTIR, UV-vis, and HPLC measurements for structural, quantitative and qualitative information about complexes in the bulk, and potential degradation products. The implications of our studies on understanding interfacial and condensed phase chemistry relevant to multicomponent aerosols, water thin islands on buildings, and ocean surfaces containing transition metals will be discussed.

Effect of granular porous media on the composting of swine manure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Ku-Yong; Kim, Hyun-Woo; Han, Sun-Kee

2008-11-15

This study investigated the feasibility of a bulking agent of granular porous media (GPM) for the composting of swine manure. Two lab-scale composting reactors were operated to evaluate the general performances and maturity parameters using GPM made of wastes from the Portland cement manufacturing processes as an alternative bulking agent. The overall volatile solid (VS) removal was 38.5% (dry basis). During the experiments, moisture content ranged between 41% and 53%, ensuring feasibility of microbial activity in composting. Cured compost showed proper maturity and low phytotoxicity, despite the slight decreases of CO{sub 2} production and VS removal at the second batchmore » operation. Various physico-chemical parameters of the cured compost met the regulatory standards reported elsewhere. The pH, carbon-to-nitrogen ratio, ammonia nitrogen and soluble organic carbon (SOC) of the cured compost were significantly correlated to the germination index (GI) using the seeds of Chinese cabbage and lettuce, indicating the progressive biodegradation of phytotoxins as well as organic matter. Consequently, the results obtained in this study demonstrate that GPM could contribute to the environmentally friendly and economical composting of problematic swine manure as a recyclable bulking agent.« less

The Relationship between Bulk and Mobile Forms of Heavy Metals in Soils of Kursk

NASA Astrophysics Data System (ADS)

Nevedrov, N. P.; Protsenko, E. P.; Glebova, I. V.

2018-01-01

The contamination of Kursk urboecotopes by heavy metals (Pb, Cd, Zn, Cu, Ni) is considered. The relationships between the contents of bulk and mobile forms of heavy metal ions have been examined. The results of monitoring studies attest to a tendency for the accumulation of both bulk and mobile forms of heavy metals in the humus-accumulative horizon, except for bulk cadmium and mobile nickel. Linear and nonlinear regression models of the bulk contents of Pb, Cd, Zn, and Ni as dependent on the contents of their mobile forms have been developed. These models allow us to calculate the bulk content of heavy metal ions in the soils of urboecotopes using simpler methods of the extraction and laboratory determination of their mobile forms.

[Spatial variation characteristics of surface soil water content, bulk density and saturated hydraulic conductivity on Karst slopes].

PubMed

Zhang, Chuan; Chen, Hong-Song; Zhang, Wei; Nie, Yun-Peng; Ye, Ying-Ying; Wang, Ke-Lin

2014-06-01

Surface soil water-physical properties play a decisive role in the dynamics of deep soil water. Knowledge of their spatial variation is helpful in understanding the processes of rainfall infiltration and runoff generation, which will contribute to the reasonable utilization of soil water resources in mountainous areas. Based on a grid sampling scheme (10 m x 10 m) and geostatistical methods, this paper aimed to study the spatial variability of surface (0-10 cm) soil water content, soil bulk density and saturated hydraulic conductivity on a typical shrub slope (90 m x 120 m, projected length) in Karst area of northwest Guangxi, southwest China. The results showed that the surface soil water content, bulk density and saturated hydraulic conductivity had different spatial dependence and spatial structure. Sample variogram of the soil water content was fitted well by Gaussian models with the nugget effect, while soil bulk density and saturated hydraulic conductivity were fitted well by exponential models with the nugget effect. Variability of soil water content showed strong spatial dependence, while the soil bulk density and saturated hydraulic conductivity showed moderate spatial dependence. The spatial ranges of the soil water content and saturated hydraulic conductivity were small, while that of the soil bulk density was much bigger. In general, the soil water content increased with the increase of altitude while it was opposite for the soil bulk densi- ty. However, the soil saturated hydraulic conductivity had a random distribution of large amounts of small patches, showing high spatial heterogeneity. Soil water content negatively (P < 0.01) correlated with the bulk density and saturated hydraulic conductivity, while there was no significant correlation between the soil bulk density and saturated hydraulic conductivity.

Particle characterization of poorly water-soluble drugs using a spray freeze drying technique.

PubMed

Kondo, Masahiro; Niwa, Toshiyuki; Okamoto, Hirokazu; Danjo, Kazumi

2009-07-01

A spray freeze drying (SFD) method was developed to prepare the composite particles of poorly water-soluble drug. The aqueous solution dissolved drug and the functional polymer was sprayed directly into liquid nitrogen. Then, the iced droplets were lyophilized with freeze-dryer to prepare solid particles. Tolbutamide (TBM) and hydroxypropylmethylcellulose (HPMC) were used as a model drug and water-soluble polymeric carrier in this study, respectively. The morphological observation of particles revealed that the spherical particles having porous structure could be obtained by optimizing the loading amount of drug and polymer in the spray solution. Especially, SFD method was characterized that the prepared particles had significantly larger specific surface area comparing with those prepared by the standard spray drying technique. The physicochemical properties of the resultant particles were found to be dependent on the concentration of spray solution. When the solution with high content of drug and polymer was used, the particle size of the resulting composite particles increased and they became spherical. The specific surface area of the particles also increased as a result of higher concentration of solution. The evaluation of spray solution indicated that these results were dependent on the viscosity of spray solution. In addition, when composite particles of TBM were prepared using the SFD method with HPMC as a carrier, the crystallinity of TBM decreased as the proportion of HPMC increased. When the TBM : HPMC ratio reached 1 : 5, the crystallinity of the particles completely disappeared. The dissolution tests showed that the release profiles of poorly water-soluble TBM from SFD composite particles were drastically improved compared to bulk TBM. The 70% release time T(70) of composite particles prepared by the SFD method in a solution of pH 1.2 was quite smaller than that of bulk TBM, while in a solution of pH 6.8, it was slightly lower. In addition, the release rates were faster than those of standard spray dried (SD) composite particles for solutions of pH 1.2 and 6.8, respectively. When composite particles were prepared from mixtures with various composition ratios, T(70) was found to decrease as the proportion of HPMC increased; the release rate was faster than that of bulk TBM in a solution of pH 6.8, as well as solution of pH 1.2.

Mercury pollution in Doha (Qatar) coastal environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Madfa, H.; Dahab, O.A.; Holail, H.

Surface water and sediment samples were collected from the Doha coastal area and analyzed for content of physico-chemical forms of mercury. Dissolved reactive Hg represented 81.0% of the total dissolved Hg. Organic Hg contributed only 5.0% of total Hg. Mercury showed a strong tendency to be associated with suspended matter in Doha coastal waters, as it represented about 73.0% of the total. Total Hg in bulk Doha surface sediments fluctuated between 0.14 and 1.75 [mu]g g[sup [minus]1] dry weight, with an average of 0.54 [+-] 0.46 [mu]g g[sup [minus]1] dry weight. The sediment fraction past 63 [mu]m contained 0.73 [+-]more » 0.60 [mu]g g[sup [minus]1] dry weight total Hg. Leachable and methyl Hg averaged 0.10 [+-] 0.11 and 0.02 [+-] 0.03 [mu]g g[sup [minus]1] dry weight, respectively, in the < 63-[mu]m sediment fraction. There is a general trend for all Hg species determined in water and sediments to decrease seaward. The significantly elevated Hg levels at certain locations indicated that the main Hg sources to Doha coastal environment are leachate from the solid waste disposal site, the two harbors, and surface-water discharge.« less

48 CFR 237.7101 - Solicitation provisions and contract clauses.

Code of Federal Regulations, 2011 CFR

2011-10-01

... and dry cleaning services to be provided on a bulk weight basis. (1) Insert a reasonable per pound..., Instruction to Offerors (Bulk Weight), in solicitations for laundry services to be provided on a bulk weight... laundry services on a bag type basis, insert reasonable per pound prices by bag type. (2) Insert an...

Physicochemical properties of extrudates from white yam and bambara nut blends

NASA Astrophysics Data System (ADS)

Oluwole, O. B.; Olapade, A. A.; Awonorin, S. O.; Henshaw, F. O.

2013-01-01

This study was conducted to investigate effects of extrusion conditions on physicochemical properties of blend of yam and bambara nut flours. A blend of white yam grit (750 μm) and Bambara nut flour (500 μm) in a ratio of 4:1, respectively was extrusion cooked at varying screw speeds 50-70 r.p.m., feed moisture 12.5-17.5% (dry basis) and barrel temperatures 130-150°C. The extrusion variables employed included barrel temperature, screw speed, and feed moisture content, while the physicochemical properties of the extrudates investigated were the expansion ratio, bulk density, and trypsin inhibition activity. The results revealed that all the extrusion variables had significant effects (p<0.05) on the product properties considered in this study. The expansion ratio values ranged 1.55-2.06, bulk density values ranged 0.76-0.94 g cm-3, while trypsin inhibition activities were 1.01-8.08 mg 100 g-1 sample.

Remote detection of widespread indigenous water in lunar pyroclastic deposits

NASA Astrophysics Data System (ADS)

Milliken, Ralph E.; Li, Shuai

2017-08-01

Laboratory analyses of lunar samples provide a direct means to identify indigenous volatiles and have been used to argue for the presence of Earth-like water content in the lunar interior. Some volatile elements, however, have been interpreted as evidence for a bulk lunar mantle that is dry. Here we demonstrate that, for a number of lunar pyroclastic deposits, near-infrared reflectance spectra acquired by the Moon Mineralogy Mapper instrument onboard the Chandrayaan-1 orbiter exhibit absorptions consistent with enhanced OH- and/or H2O-bearing materials. These enhancements suggest a widespread occurrence of water in pyroclastic materials sourced from the deep lunar interior, and thus an indigenous origin. Water abundances of up to 150 ppm are estimated for large pyroclastic deposits, with localized values of about 300 to 400 ppm at potential vent areas. Enhanced water content associated with lunar pyroclastic deposits and the large areal extent, widespread distribution and variable chemistry of these deposits on the lunar surface are consistent with significant water in the bulk lunar mantle. We therefore suggest that water-bearing volcanic glasses from Apollo landing sites are not anomalous, and volatile loss during pyroclastic eruptions may represent a significant pathway for the transport of water to the lunar surface.

Variability of bulk density of distillers dried grains with solubles (DDGS) during gravity-driven discharge.

PubMed

Clementson, C L; Ileleji, K E

2010-07-01

Loading railcars with consistent tonnage has immense cost implications for the shipping of distillers' dried grains with soluble (DDGS) product. Therefore, this study was designed to investigate the bulk density variability of DDGS during filling of railcar hoppers. An apparatus was developed similar to a spinning riffler sampler in order to simulate the filling of railcars at an ethanol plant. There was significant difference (P<0.05) between the initial and final measures of bulk density and particle size as the hoppers were emptied in both mass and funnel flow patterns. Particle segregation that takes place during filling of hoppers contributed to the bulk density variation and was explained by particle size variation. This phenomenon is most likely the same throughout the industry and an appropriate sampling procedure should be adopted for measuring the bulk density of DDGS stored silos or transported in railcar hoppers. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Fractionation and risk assessment of Fe and Mn in surface sediments from coastal sites of Sonora, Mexico (Gulf of California).

PubMed

Jara-Marini, Martín E; García-Camarena, Raúl; Gómez-Álvarez, Agustín; García-Rico, Leticia

2015-07-01

The aim of this study was to evaluate Fe and Mn distribution in geochemical fractions of the surface sediment of four oyster culture sites in the Sonora coast, Mexico. A selective fractionation scheme to obtain five fractions was adapted for the microwave system. Surface sediments were analyzed for carbonates, organic matter contents, and Fe and Mn in geochemical fractions. The bulk concentrations of Fe ranged from 10,506 to 21,918 mg/kg (dry weight, dry wt), and the bulk concentrations of Mn ranged from 185.1 to 315.9 mg/kg (dry wt) in sediments, which was low and considered as non-polluted in all of the sites. The fractionation study indicated that the major geochemical phases for the metals were the residual, as well as the Fe and Mn oxide fractions. The concentrations of metals in the geochemical fractions had the following order: residual > Fe and Mn oxides > organic matter > carbonates > interchangeable. Most of the Fe and Mn were linked to the residual fraction. Among non-residual fractions, high percentages of Fe and Mn were linked to Fe and Mn oxides. The enrichment factors (EFs) for the two metals were similar in the four studied coasts, and the levels of Fe and Mn are interpreted as non-enrichment (EF < 1) because the metals concentrations were within the baseline concentrations. According to the environmental risk assessment codes, Fe and Mn posed no risk and low risk, respectively. Although the concentrations of Fe and Mn were linked to the residual fraction, the levels in non-residual fractions may significantly result in the transference of other metals, depending on several physico-chemical and biological factors.

The impact of compaction, moisture content, particle size and type of bulking agent on initial physical properties of sludge-bulking agent mixtures before composting.

PubMed

Huet, J; Druilhe, C; Trémier, A; Benoist, J C; Debenest, G

2012-06-01

This study aimed to experimentally acquire evolution profiles between depth, bulk density, Free Air Space (FAS), air permeability and thermal conductivity in initial composting materials. The impact of two different moisture content, two particle size and two types of bulking agent on these four parameters was also evaluated. Bulk density and thermal conductivity both increased with depth while FAS and air permeability both decreased with it. Moreover, depth and moisture content had a significant impact on almost all the four physical parameters contrary to particle size and the type of bulking agent. Copyright © 2012 Elsevier Ltd. All rights reserved.

Methods of synthesizing hydroxyapatite powders and bulk materials

DOEpatents

Luo, Ping

1999-01-12

Methods are provided for producing non-porous controlled morphology hydroxyapatite granules of less than 8 .mu.m by a spray-drying process. Solid or hollow spheres or doughnuts can be formed by controlling the volume fraction and viscosity of the slurry as well as the spray-drying conditions. Methods of providing for homogenous cellular structure hydroxyapatite granules are also provided. Pores or channels or varying size and number can be formed by varying the temperature at which a hydroxyapatite slurry formed in basic, saturated ammonium hydroxide is spray-dried. Methods of providing non-porous controlled morphology hydroxyapatite granules in ammonium hydroxide are also provided. The hydroxyapatite granules and bulk materials formed by these methods are also provided.

Methods of synthesizing hydroxyapatite powders and bulk materials

DOEpatents

Luo, P.

1999-01-12

Methods are provided for producing non-porous controlled morphology hydroxyapatite granules of less than 8 {micro}m by a spray-drying process. Solid or hollow spheres or doughnuts can be formed by controlling the volume fraction and viscosity of the slurry as well as the spray-drying conditions. Methods of providing for homogeneous cellular structure hydroxyapatite granules are also provided. Pores or channels or varying size and number can be formed by varying the temperature at which a hydroxyapatite slurry formed in basic, saturated ammonium hydroxide is spray-dried. Methods of providing non-porous controlled morphology hydroxyapatite granules in ammonium hydroxide are also provided. The hydroxyapatite granules and bulk materials formed by these methods are also provided. 26 figs.

46 CFR 154.1170 - Hand hose line: General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Firefighting System: Dry Chemical § 154.1170 Hand hose line: General. Each dry chemical hand hose line must: (a...

Comparison between fractionation and bioavailability of trace elements in rhizosphere and bulk soils.

PubMed

Wang, Zhongwen; Shan, Xiao-Quan; Zhang, Shuzhen

2002-03-01

Rhizosphere is a microbiosphere and has quite different chemical, physical and biological properties from bulk soils. A greenhouse experiment was performed to compare the difference of fractionation and bioavailability of trace elements Cr, Ni, Zn, Cu, Pb and Cd between rhizosphere soil and bulk soil. In the meantime, the influence of air-drying on the fractionation and bioavailability was also investigated by using wet soil sample as a control. Soils in a homemade rhizobox were divided into four zones: rhizosphere, near rhizosphere, near bulk soil and bulk soil zones, which was designated as S1, S2, S3 and S4. Elemental speciations were fractionated to water soluble, exchangeable and carbonate bound (B1), Fe-Mn oxide bound (B2), and organic and sulfide bound (B3) by a sequential extraction procedure. Speciation differences were observed for elements Cr, Ni, Zn, Cu, Pb and Cd between the rhizosphere and bulk soils, and between the air-dried and wet soils as well. The concentrations of all six heavy metals in fraction B1 followed the order of S2 > S3 > S1 > S4 and for B2, the order was S2 > S3 S4 > S1. For B3, the order was S1 > S3 S4 > S2, while for Cd the order was S2 > S3 approximately/= S4 > S1. The air-drying increased elemental concentration in fractions B1 and B2 by 20-50% and decreased in fraction B3 by about 20-100%. Correlation analysis also indicated that the bioavailability correlation coefficient of fraction B1 in rhizosphere wet soil to plants was better than that between either air-dried or nonrhizosphere soils. Therefore, application of rhizosphere wet soils should be recommended in the future study on the speciation analysis of trace elements in soils and bioavailability.

Particle Engineering Via Mechanical Dry Coating in the Design of Pharmaceutical Solid Dosage Forms.

PubMed

Qu, Li; Morton, David A V; Zhou, Qi Tony

2015-01-01

Cohesive powders are problematic in the manufacturing of pharmaceutical solid dosage forms because they exhibit poor flowability, fluidization and aerosolization. These undesirable bulk properties of cohesive powders represent a fundamental challenge in the design of efficient pharmaceutical manufacturing processes. Recently, mechanical dry coating has attracted increasing attention as it can improve the bulk properties of cohesive powders in a cheaper, simpler, safer and more environment-friendly way than the existing solvent-based counterparts. In this review, mechanical dry coating techniques are outlined and their potential applications in formulation and manufacturing of pharmaceutical solid dosage forms are discussed. Reported data from the literature have shown that mechanical dry coating holds promise for the design of superior pharmaceutical solid formulations or manufacturing processes by engineering the interfaces of cohesive powders in an efficient and economical way.

Effect of different drying techniques on flowability characteristics and chemical properties of natural carbohydrate-protein Gum from durian fruit seed

PubMed Central

2013-01-01

Background A natural carbohydrate biopolymer was extracted from the agricultural biomass waste (durian seed). Subsequently, the crude biopolymer was purified by using the saturated barium hydroxide to minimize the impurities. Finally, the effect of different drying techniques on the flow characteristics and functional properties of the purified biopolymer was investigated. The present study elucidated the main functional characteristics such as flow characteristics, water- and oil-holding capacity, solubility, and foaming capacity. Results In most cases except for oven drying, the bulk density decreased, thus increasing the porosity. This might be attributed to the increase in the inter-particle voids of smaller sized particles with larger contact surface areas per unit volume. The current study revealed that oven-dried gum and freeze-dried gum had the highest and lowest compressibility index, thus indicating the weakest and strongest flowability among all samples. In the present work, the freeze-dried gum showed the lowest angle of repose, bulk, tapped and true density. This indicates the highest porosity degree of freeze dried gum among dried seed gums. It also exhibited the highest solubility, and foaming capacity thus providing the most desirable functional properties and flow characteristics among all drying techniques. Conclusion The present study revealed that freeze drying among all drying techniques provided the most desirable functional properties and flow characteristics for durian seed gum. PMID:23289739

Use of two varieties of hard-to-cook beans (Phaseolus vulgaris) and cowpeas (Vigna unguiculata) in the processing of koki (a steamed legume product).

PubMed

Mbofung, C M; Rigby, N; Waldron, K

1999-01-01

Koki is a nutritious cowpea-based food product usually processed by steam cooking whipped cowpea (Vigna unguiculata) paste mixed with spices and palm oil. A study was carried out to investigate the effect of the partial replacement of cowpeas (CP) with hard-to-cook (HTC) beans on the chemical, nutritional and sensory characteristics of koki. Towards this objective, two varieties of beans--Phaseolus vulgaris (red kidney beans--RKB and mottled brown beans--MBB), each with the HTC defect, were separately incorporated into cowpea paste in the following Bean:CP ratios 0:100, 20:80, 30:70, 40:60, 50:50, 60:40 and processed into koki. Incorporation of dry HTC beans into cowpeas in the making of koki affected the bulking properties of the uncooked paste, the nutrient composition, essential amino acid content, antinutritional factors, digestibility as well as the sensory attributes of cooked koki. Sensory tests showed that a highly acceptable, nutritious and digestible koki can be processed from cowpeas partially replaced with dry HTC bean paste up to levels of about 40-50% depending on the variety of dry bean used.

Gamma-Ray Attenuation to Evaluate Soil Porosity: An Analysis of Methods

PubMed Central

Pires, Luiz F.; Pereira, André B.

2014-01-01

Soil porosity (ϕ) is of a great deal for environmental studies due to the fact that water infiltrates and suffers redistribution in the soil pore space. Many physical and biochemical processes related to environmental quality occur in the soil porous system. Representative determinations of ϕ are necessary due to the importance of this physical property in several fields of natural sciences. In the current work, two methods to evaluate ϕ were analyzed by means of gamma-ray attenuation technique. The first method uses the soil attenuation approach through dry soil and saturated samples, whereas the second one utilizes the same approach but taking into account dry soil samples to assess soil bulk density and soil particle density to determine ϕ. The results obtained point out a good correlation between both methods. However, when ϕ is obtained through soil water content at saturation and a 4 mm collimator is used to collimate the gamma-ray beam the first method also shows good correlations with the traditional one. PMID:24616640

Effect of resin infiltration on the thermal and mechanical properties of nano-sized silica-based thermal insulation.

PubMed

Lee, Jae Chun; Kim, Yun-Il; Lee, Dong-Hun; Kim, Won-Jun; Park, Sung; Lee, Dong Bok

2011-08-01

Several kinds of nano-sized silica-based thermal insulation were prepared by dry processing of mixtures consisting of fumed silica, ceramic fiber, and a SiC opacifier. Infiltration of phenolic resin solution into the insulation, followed by hot-pressing, was attempted to improve the mechanical strength of the insulation. More than 22% resin content was necessary to increase the strength of the insulation by a factor of two or more. The structural integrity of the resin-infiltrated samples could be maintained, even after resin burn-out, presumably due to reinforcement from ceramic fibers. For all temperature ranges and similar sample bulk density values, the thermal conductivities of the samples after resin burn-out were consistently higher than those of the samples obtained from the dry process. Mercury intrusion curves indicated that the median size of the nanopores formed by primary silica aggregates in the samples after resin burn-out is consistently larger than that of the sample without resin infiltration.

The bulk composition and leaching properties of electroplating sludge prior/following the solidification/stabilization by calcium oxide.

PubMed

Orescanin, Visnja; Mikulic, Nenad; Mikelic, Ivanka Lovrencic; Posedi, Mario; Kampic, Stefica; Medunic, Gordana

2009-10-01

Eighteen samples of electroplating sludge were taken from three vertical profiles of waste storage pond of the zinc plating facility. Dry matter and organic matter content, pH value, bulk concentrations and leachate composition were determined. A sludge sample with the highest zinc value in the leachate was treated with calcium oxide (10% to 70%) and the obtained solidificate was repeatedly tested. There were found significant variations of all measured parameters among the profiles of untreated waste. Dry matter content varied from 125 to 455 mgg(-1), organic matter varied from 94.3 to 293.9 mgg(-1), and pH value varied from 3.42 to 5.90 (mean 4.34). Iron content ranged from 38.4 to 191.4 mgg(-1) (mean 136 mgg(-1); RSD 0.25), while zinc ranged from 10.9 to 58.2 mgg(-1) (mean 33.4 mgg(-1); RSD 0.38). According to its DIN38414-S4 leachate composition, this material was not suitable for landfilling of inert waste since zinc and nickel mean values were 10 and 1.5 times higher, respectively, and maximum values 27 and 2.5 times higher, respectively, compared to the upper permissible limit. Maximum values of Cr(VI), Fe, Ni, Cu, and Zn in the DIN38414-S4 leachate were 0.183 mgL(-1), 34.085 mgL(-1), 1.052 mgL(-1), 0.829 mgL(-1) and 107.475 mgL(-1)L, respectively. Following the solidification/stabilization procedure with CaO (sample/CaO = 90/10), concentrations of Cr(VI), Fe, Cu and Zn were reduced 92, 44, 66 and 57 times, respectively, compared to the untreated sample. The addition of 50% of CaO into the sludge reduced zinc and nickel concentrations 79 and 45 times, respectively, in the DIN38414-S4 leachate of the solidified waste compared to the original sludge, thereby converting an hazardous waste into the inert material suitable for landfilling or reuse in the construction processes.

Oxidative stability of high-oleic sunflower oil in a porous starch carrier.

PubMed

Belingheri, Claudia; Giussani, Barbara; Rodriguez-Estrada, Maria Teresa; Ferrillo, Antonio; Vittadini, Elena

2015-01-01

This study evaluates the oxidation level of high-oleic sunflower oil (HOSO) plated onto porous starch as an alternative to spray drying. Encapsulated oils were subjected to accelerated oxidation by heat and light exposure, and peroxide value (PV) and conjugated dienes (CD) were measured. Bulk oil was the control. PV increased in all samples with increased light exposure, with similar values being reached by oil carried on porous starch and spray dried oil. The encapsulation processes determined a reduced effect of light on the increase of CD in the oil, as compared to bulk oil. Spray dried oil presented the highest CD in the experimental domain considered. Since similar levels of PV and lower levels of CD were shown in the HOSO carried on porous starch compared to the spray dried HOSO, plating flavour oils on porous starch could be a suitable technological alternative to spray drying, for flavour encapsulation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Origin of the Martian Moons and Their Volatile Abundances

NASA Astrophysics Data System (ADS)

Nakajima, M.; Canup, R. M.

2017-12-01

The origin of the Martian moons, Phobos and Deimos, has been actively debated. These moons were initially thought to have been gravitationally captured asteroids given that their spectra appeared to be similar to those of D-type asteroids. However, intact capture is difficult to reconcile with their nearly circular, co-planar orbits. Their orbits may be better explained by recent dynamical studies that suggest that the moons may have instead formed from a disk generated by a large impact, as was likely the case for Earth's Moon. Phobos and Deimos' bulk volatile contents, which are currently very uncertain, would also provide key constraints on their origin. If the moons were captured, their bulk compositions may be similar to those of asteroids, and their sub-surfaces could be volatile-rich. We are here exploring the implications of the alternative impact origin on the moon volatile abundances. We perform numerical simulations to estimate the extent of volatile loss from the moon-forming ejecta produced by a large impact with Mars. We find that hydrogen and water vapor escape hydrodynamically from the disk, leading to moons with dry, hydrogen-depleted bulk compositions. It is thus possible that the moons' mode of origin may be determined by knowledge of their volatile contents, because detection of a substantial (non-exogenically delivered) water content would argue strongly against formation by impact. JAXA's Martian Moons eXploration Mission (MMX) will conduct detailed remote sensing of the moons, including a gamma ray and neutron spectrometer that will for the first time probe their sub-surface elemental compositions, and will return samples from Phobos for laboratory analysis. This should allow for characterization of the moon volatile abundances. We also discuss that the inferred high porosities of these moons could be explained if they are rubble piles formed during accretion from impact-produced ejecta.

Variation of the Phytochemical Constituents and Antioxidant Activities of Zingiber officinale var. rubrum Theilade Associated with Different Drying Methods and Polyphenol Oxidase Activity.

PubMed

Ghasemzadeh, Ali; Jaafar, Hawa Z E; Rahmat, Asmah

2016-06-17

The effects of different drying methods (freeze drying, vacuum oven drying, and shade drying) on the phytochemical constituents associated with the antioxidant activities of Z. officinale var. rubrum Theilade were evaluated to determine the optimal drying process for these rhizomes. Total flavonoid content (TFC), total phenolic content (TPC), and polyphenol oxidase (PPO) activity were measured using the spectrophotometric method. Individual phenolic acids and flavonoids, 6- and 8-gingerol and shogaol were identified by ultra-high performance liquid chromatography method. Ferric reducing antioxidant potential (FRAP) and 1,1-diphenyl-2-picrylhydrazyl (DPPH) assays were used for the evaluation of antioxidant activities. The highest reduction in moisture content was observed after freeze drying (82.97%), followed by vacuum oven drying (80.43%) and shade drying (72.65%). The highest TPC, TFC, and 6- and 8-shogaol contents were observed in samples dried by the vacuum oven drying method compared to other drying methods. The highest content of 6- and 8-gingerol was observed after freeze drying, followed by vacuum oven drying and shade drying methods. Fresh samples had the highest PPO activity and lowest content of flavonoid and phenolic acid compounds compared to dried samples. Rhizomes dried by the vacuum oven drying method represent the highest DPPH (52.9%) and FRAP activities (566.5 μM of Fe (II)/g DM), followed by freeze drying (48.3% and 527.1 μM of Fe (II)/g DM, respectively) and shade drying methods (37.64% and 471.8 μM of Fe (II)/g DM, respectively) with IC50 values of 27.2, 29.1, and 34.8 μg/mL, respectively. Negative and significant correlations were observed between PPO and antioxidant activity of rhizomes. Vacuum oven dried rhizomes can be utilized as an ingredient for the development of value-added food products as they contain high contents of phytochemicals with valuable antioxidant potential.

A Permeable Active Amendment Concrete (PAAC) for Contaminant Remediation and Erosion Control

DTIC Science & Technology

2012-06-01

124: 131 -143. SRNL-STI-2012-00356 70 Tessier, A., Campbell, P.G.C., and Bisson, M. 1979. Sequential extraction procedure for the speciation of...Bulk Density, Dry, (AI( C-D)]* p, pcf 134.85 Bulk Dens ity after Immersion, [BI(C-D)]* p, pcf 146.65 Bulk Density after Immersion & Boiling1 jCI (C

Arbuscular Mycorrhiza Alleviates Restrictions to Substrate Water Flow and Delays Transpiration Limitation to Stronger Drought in Tomato

PubMed Central

Bitterlich, Michael; Sandmann, Martin; Graefe, Jan

2018-01-01

Arbuscular mycorrhizal fungi (AMF) proliferate in soil pores, on the surface of soil particles and affect soil structure. Although modifications in substrate moisture retention depend on structure and could influence plant water extraction, mycorrhizal impacts on water retention and hydraulic conductivity were rarely quantified. Hence, we asked whether inoculation with AMF affects substrate water retention, water transport properties and at which drought intensity those factors become limiting for plant transpiration. Solanum lycopersicum plants were set up in the glasshouse, inoculated or not with Funneliformis mosseae, and grown for 35 days under ample water supply. After mycorrhizal establishment, we harvested three sets of plants, one before (36 days after inoculation) and the second (day 42) and third (day 47) within a sequential drying episode. Sampling cores were introduced into pots before planting. After harvest, moisture retention and substrate conductivity properties were assessed and water retention and hydraulic conductivity models were fitted. A root water uptake model was adopted in order to identify the critical substrate moisture that induces soil derived transpiration limitation. Neither substrate porosity nor saturated water contents were affected by inoculation, but both declined after substrates dried. Drying also caused a decline in pot water capacity and hydraulic conductivity. Plant available water contents under wet (pF 1.8–4.2) and dry (pF 2.5–4.2) conditions increased in mycorrhizal substrates and were conserved after drying. Substrate hydraulic conductivity was higher in mycorrhizal pots before and during drought exposure. After withholding water from pots, higher substrate drying rates and lower substrate water potentials were found in mycorrhizal substrates. Mycorrhiza neither affected leaf area nor root weight or length. Consistently with higher substrate drying rates, AMF restored the plant hydraulic status, and increased plant transpiration when soil moisture declined. The water potential at the root surface and the resistance to water flow in the rhizosphere were restored in mycorrhizal pots although the bulk substrate dried more. Finally, substrates colonized by AMF can be more desiccated before substrate water flux quantitatively limits transpiration. This is most pronounced under high transpiration demands and complies with a difference of over 1,000 hPa in substrate water potential. PMID:29503655

Disruption rates for one vulnerable soil in Organ Pipe Cactus National Monument, Arizona, USA

USGS Publications Warehouse

Webb, Robert H.; Esque, Todd C.; Nussear, Kenneth E.; Sturm, Mark

2013-01-01

Rates of soil disruption from hikers and vehicle traffic are poorly known, particularly for arid landscapes. We conducted an experiment in Organ Pipe Cactus National Monument (ORPI) in western Arizona, USA, on an air-dry very fine sandy loam that is considered to be vulnerable to disruption. We created variable-pass tracks using hikers, an all-terrain vehicle (ATV), and a four-wheel drive vehicle (4WD) and measured changes in cross-track topography, penetration depth, and bulk density. Hikers (one pass = 5 hikers) increased bulk density and altered penetration depth but caused minimal surface disruption up to 100 passes; a minimum of 10 passes were required to overcome surface strength of this dry soil. Both ATV and 4WD traffic significantly disrupted the soil with one pass, creating deep ruts with increasing passes that rendered the 4WD trail impassable after 20 passes. Despite considerable soil loosening (dilation), bulk density increased in the vehicle trails, and lateral displacement created berms of loosened soil. This soil type, when dry, can sustain up to 10 passes of hikers but only one vehicle pass before significant soil disruption occurs; greater disruption is expected when soils are wet. Bulk density increased logarithmically with applied pressure from hikers, ATV, and 4WD.

Relationships between surface coverage ratio and powder mechanics of binary adhesive mixtures for dry powder inhalers.

PubMed

Rudén, Jonas; Frenning, Göran; Bramer, Tobias; Thalberg, Kyrre; Alderborn, Göran

2018-04-25

The aim of this paper was to study relationships between the content of fine particles and the powder mechanics of binary adhesive mixtures and link these relationships to the blend state. Mixtures with increasing amounts of fine particles (increasing surface coverage ratios (SCR)) were prepared using Lactopress SD as carrier and micro particles of lactose as fines (2.7 µm). Indicators of unsettled bulk density, compressibility and flowability were derived and the blend state was visually examined by imaging. The powder properties studied showed relationships to the SCR characterised by stages. At low SCR, the fine particles predominantly gathered in cavities of the carriers, giving increased bulk density and unchanged or improved flow. Thereafter, increased SCR gave a deposition of particles at the enveloped carrier surface with a gradually more irregular adhesion layer leading to a reduced bulk density and a step-wise reduced flowability. The mechanics of the mixtures at a certain stage were dependent on the structure and the dynamics of the adhesion layer and transitions between the stages were controlled by the evolution of the adhesion layer. It is advisable to use techniques based on different types of flow in order to comprehensively study the mechanics of adhesive mixtures. Copyright © 2018 Elsevier B.V. All rights reserved.

[Effects of different drying methods on processing performance and quality in bulbus of Tulipa edulis].

PubMed

Yang, Xiao-hua; Guo, Qiao-sheng; Zhu, Zai-biao; Chen, Jun; Miao, Yuan-yuan; Yang, Ying; Sun, Yuan

2015-10-01

Effects of different drying methods including sun drying, steamed, boiled, constant temperature drying (at 40, 50, 60 °C) on appearance, hardness, rehydration ratio, dry rate, moisture, total ash, extractive and polysaccharides contents were studied to provide the basis of standard processing method for Tulipa edulis bulbus. The results showed that the treatments of sun drying and 40 °C drying showed higher rehydration ratios, but lower dry rate, higher hardness, worse color, longer time and obvious distortion and shrinkage in comparison with other drying methods. The treatments of 60 °C constant temperature drying resulted in shorter drying time, lower water and higher polysaccharides content. Drying time is shorter and appearance quality is better in the treatment of steaming and boiling compared with other treatments, but the content of extractive and polysaccharides decreased significantly. The treatments of 50 °C constant temperature drying led to similar appearance quality of bulb to commercial bulb, and it resulted in lowest hardness and highest dry rate as well as higher rehydration ratio, extractive and polysaccharides content, moderate moisture and total ash contents among these treatments. Based on the results obtained, 50 °C constant temperature drying is the better way for the processing of T. edulis bulbus.

48 CFR 752.247-70 - Preference for privately owned U.S.-flag commercial vessels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (computed separately for dry bulk carriers, dry cargo liners, and tankers) shall be transported in privately... registry. (iv) Date of loading. (v) Port of loading. (vi) Port of final discharge. (vii) Description of...

Evaluating industrial drying of cellulosic feedstock for bioenergy: A systems approach

DOE PAGES

Sokhansanj, Shahab; Webb, Erin

2016-01-21

Here, a large portion of herbaceous and woody biomass must be dried following harvest. Natural field drying is possible if the weather cooperates. Mechanical drying is a certain way of reducing the moisture content of biomass. This paper presents an engineering analysis applied to drying of 10 Mg h –1 (exit mass flow) of biomass with an initial moisture content ranging from 25% to 70% (wet mass basis) down to 10% exit moisture content. The requirement for hog fuel to supply heat to the dryer increases from 0.5 dry Mg to 3.8 dry Mg h –1 with the increased initialmore » moisture of biomass. The capital cost for the entire drying system including equipment for biomass size reduction, pollution control, dryer, and biomass combustor sums up to more than 4.7 million dollars. The operating cost (electricity, labor, repair, and maintenance) minus fuel cost for the dryer alone amount to 4.05 Mg –1 of dried biomass. For 50% moisture content biomass, the cost of fuel to heat the drying air is 7.41 dollars/ dry ton of biomass for a total 11.46 dollars per dry ton at 10% moisture content. The fuel cost ranges from a low of 2.21 dollars to a high of 18.54 dollars for a biomass at an initial moisture content of 25% to 75%, respectively. This wide range in fuel cost indicates the extreme sensitivity of the drying cost to initial moisture content of biomass and to ambient air humidity and temperature and highlights the significance of field drying for a cost effective drying operation.« less

Estimating carbon and nitrogen pools in a forest soil: Influence of soil bulk density methods and rock content

Treesearch

Martin F. Jurgensen; Deborah S. Page-Dumroese; Robert E. Brown; Joanne M. Tirocke; Chris A. Miller; James B. Pickens; Min Wang

2017-01-01

Soils with high rock content are common in many US forests, and contain large amounts of stored C. Accurate measurements of soil bulk density and rock content are critical for calculating and assessing changes in both C and nutrient pool size, but bulk density sampling methods have limitations and sources of variability. Therefore, we evaluated the use of small-...

Effect of immobilized rhizobacteria and organic amendment in bulk and rhizospheric soil of Cistus albidus L.

NASA Astrophysics Data System (ADS)

Mengual, Carmen Maria; del Mar Alguacil, Maria; Roldan, Antonio; Schoebitz, Mauricio

2013-04-01

A field experiment was carried out to assess the effectiveness of the immobilized microbial inoculant and the addition of organic olive residue. The microbial inoculant contained two rhizobacterial species identified as Azospirillum brasilense and Pantoea dispersa immobilized in a natural inert support. Bacterial population densities were 3.5×109 and 4.1×109 CFU g-1 of A. brasilense M3 and P. dispersa C3, respectively. The amendment used was the organic fraction extracted with KOH from composted "alperujo". The raw material was collected from an olive-mill and mixed with fresh cow bedding as bulking agent for composting. The inoculation of rhizobacteria and the addition of organic residue were employed for plant growth promotion of Cistus albidus L. and enhancement of soil physicochemical, biochemical and biological properties in a degraded semiarid Mediterranean area. One year after planting, the available phosphorus and potassium content in the amended soils was about 100 and 70% respectively higher than in the non-amended soil. Microbial inoculant and their interaction with organic residue increased the aggregate stability of the rhizosphere soil of C. albidus (by 12% with respect to control soil) while the organic residue alone not increased the aggregate stability of the rhizosphere of C. albidus. Microbial biomass C content and enzyme activities (dehydrogenase, urease, protease-BAA and alkaline phosphatase) of the rhizosphere of C. albidus were increased by microbial inoculant and organic residue interaction but not by microbial inoculation alone. The microbial inoculant and organic residue interaction were the most effective treatment for stimulating the roots dry weight of C. albidus (by 133% with respect to control plants) and microbial inoculant was the most effective treatment for increase the shoot dry weigh of plants (by 106% with respect to control plants). The combined treatment, involving microbial inoculant and addition of the organic residue directly into the soil, had additive effect on the root growth of C. albidus and chemical and biological quality of soil.

Method to produce durable pellets at lower energy consumption using high moisture corn stover and a corn starch binder in a flat die pellet mill

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumuluru, Jaya Shankar; Conner, Craig C.; Hoover, Amber N.

Biomass from plants can serve as an alternative renewable energy resources for energy production. Low densities of 40–60 kg/m3 for ground lignocellulosic biomass like corn stover limit its operation for energy purposes. The common drawbacks are inefficient transportation, a bigger storage foot print, and handling problems. Densification of biomass using pellet mill helps to overcome these limitations. This study helps to understand the effect of binder on high moisture biomass with a focus on the quality (density and durability), the pelleting efficiency and the specific energy consumption of its pelleting process. Raw corn stover was pelleted at high moisture ofmore » 33% (w.b.) at both varying preheating temperatures and binder percentage. The die speed of the pellet mill was set at 60Hz. The pellets produced were analyzed and showed higher moisture content. They were further dried in a laboratory oven at 70°C for 3-4 hr bringing the pellet moisture to <9%. The dried pellets were evaluated for their physical properties like unit, bulk and tapped density, and durability. Furthermore, the results indicated increasing the binder percentage to 4% improved the physical properties of the pellets and reduced the specific energy consumption. Higher binder addition of 4% reduced the feedstock moisture loss during pelleting to <4%, which can be due reduced residence time of the material in the die. On the other hand the physical properties like density and durability improved significantly with binder addition. At 4% binder and 33% feedstock moisture content, the bulk density and durability values observed were >510 kg/m3 and >98% and the percent fines generation has reduced to <3%. Also at these conditions the specific energy consumption was reduced by about 30-40% compared no binder pelleting test.« less

Method to produce durable pellets at lower energy consumption using high moisture corn stover and a corn starch binder in a flat die pellet mill

DOE PAGES

Tumuluru, Jaya Shankar; Conner, Craig C.; Hoover, Amber N.

2016-06-15

Biomass from plants can serve as an alternative renewable energy resources for energy production. Low densities of 40–60 kg/m3 for ground lignocellulosic biomass like corn stover limit its operation for energy purposes. The common drawbacks are inefficient transportation, a bigger storage foot print, and handling problems. Densification of biomass using pellet mill helps to overcome these limitations. This study helps to understand the effect of binder on high moisture biomass with a focus on the quality (density and durability), the pelleting efficiency and the specific energy consumption of its pelleting process. Raw corn stover was pelleted at high moisture ofmore » 33% (w.b.) at both varying preheating temperatures and binder percentage. The die speed of the pellet mill was set at 60Hz. The pellets produced were analyzed and showed higher moisture content. They were further dried in a laboratory oven at 70°C for 3-4 hr bringing the pellet moisture to <9%. The dried pellets were evaluated for their physical properties like unit, bulk and tapped density, and durability. Furthermore, the results indicated increasing the binder percentage to 4% improved the physical properties of the pellets and reduced the specific energy consumption. Higher binder addition of 4% reduced the feedstock moisture loss during pelleting to <4%, which can be due reduced residence time of the material in the die. On the other hand the physical properties like density and durability improved significantly with binder addition. At 4% binder and 33% feedstock moisture content, the bulk density and durability values observed were >510 kg/m3 and >98% and the percent fines generation has reduced to <3%. Also at these conditions the specific energy consumption was reduced by about 30-40% compared no binder pelleting test.« less

Infrared Thermography for Monitoring of Freeze-Drying Processes: Instrumental Developments and Preliminary Results

PubMed Central

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-01-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from −40°C to 25°C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5°C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8°C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13°C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10°C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union 103:2088–2097, 2014 PMID:24902839

Infrared thermography for monitoring of freeze-drying processes: instrumental developments and preliminary results.

PubMed

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-07-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from -40 °C to 25 °C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5 °C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8 °C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13 °C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10 °C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union.

Pulverization of coffee silverskin extract as a source of antioxidant

NASA Astrophysics Data System (ADS)

Tan, S.; Kusumocahyo, S. P.; Widiputri, D. I.

2016-11-01

Coffee silverskin (CS) is waste from coffee roasting process that has a value as source of antioxidant. In this research, two types of variant coffee Robusta and Arabica CS were extracted for their phenolic content, flavonoid content, and antioxidant activity. The extraction was done at 40°C for 60 minutes using hydroalcoholic solvent. The phenolic, flavonoid content, and antioxidant activity of Robusta CS extract were 816.75 ± 63.24 mg GAE/L and 32.82 ± 2.47 mg QE/L, and 54.80% inhibition respectively, while for Arabica CS extract were 473.51 ± 56.70 mg GAE/L, 18.58 ± 2.47 mg QE/L, and 26.30% inhibition respectively. Thus, the Robusta coffee silverskin extract has higher value of total phenolic content, flavonoid content, and antioxidant activity than Arabica coffee silverskin extract. To produce high antioxidant powder of CS extract, the effect of drying method (freeze drying and spray drying) affecting the phenolic content, flavonoid content, and antioxidant activity was evaluated. The effect of evaporation prior to both drying processes was also evaluated. Evaporation caused up to 23% of total phenolic content degradation. Spray drying resulted in dried CS extract with degradation of total phenolic content up to 17%. On the other hand, freeze drying resulted no major degradation of total phenolic content. However, the coffee silverskin extract can be directly spray dried without evaporation resulting in higher amount of phenolic content in the powder than the one which was evaporated first.

Combining Next Generation Sequencing with Bulked Segregant Analysis to Fine Map a Stem Moisture Locus in Sorghum (Sorghum bicolor L. Moench).

PubMed

Han, Yucui; Lv, Peng; Hou, Shenglin; Li, Suying; Ji, Guisu; Ma, Xue; Du, Ruiheng; Liu, Guoqing

2015-01-01

Sorghum is one of the most promising bioenergy crops. Stem juice yield, together with stem sugar concentration, determines sugar yield in sweet sorghum. Bulked segregant analysis (BSA) is a gene mapping technique for identifying genomic regions containing genetic loci affecting a trait of interest that when combined with deep sequencing could effectively accelerate the gene mapping process. In this study, a dry stem sorghum landrace was characterized and the stem water controlling locus, qSW6, was fine mapped using QTL analysis and the combined BSA and deep sequencing technologies. Results showed that: (i) In sorghum variety Jiliang 2, stem water content was around 80% before flowering stage. It dropped to 75% during grain filling with little difference between different internodes. In landrace G21, stem water content keeps dropping after the flag leaf stage. The drop from 71% at flowering time progressed to 60% at grain filling time. Large differences exist between different internodes with the lowest (51%) at the 7th and 8th internodes at dough stage. (ii) A quantitative trait locus (QTL) controlling stem water content mapped on chromosome 6 between SSR markers Ch6-2 and gpsb069 explained about 34.7-56.9% of the phenotypic variation for the 5th to 10th internodes, respectively. (iii) BSA and deep sequencing analysis narrowed the associated region to 339 kb containing 38 putative genes. The results could help reveal molecular mechanisms underlying juice yield of sorghum and thus to improve total sugar yield.

Strategies for multivariate modeling of moisture content in freeze-dried mannitol-containing products by near-infrared spectroscopy.

PubMed

Yip, Wai Lam; Gausemel, Ingvil; Sande, Sverre Arne; Dyrstad, Knut

2012-11-01

Accurate determination of residual moisture content of a freeze-dried (FD) pharmaceutical product is critical for prediction of its quality. Near-infrared (NIR) spectroscopy is a fast and non-invasive method routinely used for quantification of moisture. However, several physicochemical properties of the FD product may interfere with absorption bands related to the water content. A commonly used stabilizer and bulking agent in FD known for variation in physicochemical properties, is mannitol. To minimize this physicochemical interference, different approaches for multivariate correlation between NIR spectra of a FD product containing mannitol and the corresponding moisture content measured by Karl Fischer (KF) titration have been investigated. A novel method, MIPCR (Main and Interactions of Individual Principal Components Regression), was found to have significantly increased predictive ability of moisture content compared to a traditional PLS approach. The philosophy behind the MIPCR is that the interference from a variety of particle and morphology attributes has interactive effects on the water related absorption bands. The transformation of original wavelength variables to orthogonal scores gives a new set of variables (scores) without covariance structure, and the possibility of inclusion of interaction terms in the further modeling. The residual moisture content of the FD product investigated is in the range from 0.7% to 2.6%. The mean errors of cross validated prediction of models developed in the investigated NIR regions were reduced from a range of 24.1-27.6% for traditional PLS method to 15.7-20.5% for the MIPCR method. Improved model quality by application of MIPCR, without the need for inclusion of a large number of calibration samples, might increase the use of NIR in early phase product development, where availability of calibration samples is often limited. Copyright © 2012 Elsevier B.V. All rights reserved.

46 CFR 381.8 - Subsidized vessel participation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... rate. (c) If the amount of dry bulk cargo to be shipped is changed at any time prior to award, the... directly pay or finance all or part of U.S.-flag ocean freight transportation costs for the carriage of dry...

46 CFR 381.8 - Subsidized vessel participation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... rate. (c) If the amount of dry bulk cargo to be shipped is changed at any time prior to award, the... directly pay or finance all or part of U.S.-flag ocean freight transportation costs for the carriage of dry...

46 CFR 381.8 - Subsidized vessel participation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... rate. (c) If the amount of dry bulk cargo to be shipped is changed at any time prior to award, the... directly pay or finance all or part of U.S.-flag ocean freight transportation costs for the carriage of dry...

46 CFR 381.8 - Subsidized vessel participation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... rate. (c) If the amount of dry bulk cargo to be shipped is changed at any time prior to award, the... directly pay or finance all or part of U.S.-flag ocean freight transportation costs for the carriage of dry...

40 CFR 761.295 - Reporting and recordkeeping of the PCB concentrations in samples.

Code of Federal Regulations, 2010 CFR

2010-07-01

... On-Site Disposal of Bulk PCB Remediation Waste and Porous Surfaces in Accordance With § 761.61(a)(6... concentrations for bulk PCB remediation waste and porous surfaces on a dry weight basis and as micrograms of PCBs...

[Analysis of dynamic changes of flavonoids and alkaloids during different drying process of Morus alba leaves].

PubMed

Bai, Yong-liang; Duan, Jin-ao; Su, Shu-lan; Qian, Ye-fei; Qian, Da-wei; Ouyang, Zhen

2014-07-01

To find out dynamic changes of flavonoids and alkaloids in Morus alba leaves by analyzing influence of different drying method and drying degrees, in order to provide evidence for quality evaluation of Morus alba leaves. Different drying methods, programmed temperature methods and constant temperature methods were adopted to dry Morus alba leaves samples respectively. Contents of flavonoids and alkaloids were analyzed by HPLC-PDA and LC-TQ/MS respectively. It's shown obviously that the content of flavonoids were influenced heavily by different drying methods. Methods that suitable for flavonoids were freezing-dried > shade-dried > dried > sun-dried > microwave-dried > infrared-dried; Methods that suitable for alkaloids were freezing-dried > shade-dried > dried > sun-dried > infrared-dried > microwave-dried. The 55 -65 degrees C group was shown to be the lowest in both flavonoids and DNJ while the 85 - 95 degrees C group was shown to be the best for DNJ. For fagomine, the 45 degrees C group was shown to be the lowest concentrations while the 95 - 105 degrees C group was shown to be the highest. Samples with different moisture were shown to be different in content of flavonoids and alkaloids. And samples with 10% moisture contain highest flavonoids while those with 30% - 50% moisture contain lowest flavonoids. Content of DNJ and fagomine raised as moisture decreasing. In addition, the 55 - 65 degrees C group was better than the 95 -105 degrees C one in alkaloids content. The results provide optimal drying methods and condition for drying Morus alba leaves, and foundations for uncovering biochemical transform of Morus alba leaves.

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2013 CFR

2013-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2012 CFR

2012-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2014 CFR

2014-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

Microwave-assisted drying of blueberry (Vaccinium corymbosum L.) fruits: Drying kinetics, polyphenols, anthocyanins, antioxidant capacity, colour and texture.

PubMed

Zielinska, Magdalena; Michalska, Anna

2016-12-01

The aim of the study was to evaluate the effect of hot air convective drying (HACD), microwave vacuum drying (MWVD) and their combination (HACD+MWVD) on the drying kinetics, colour, total polyphenols, anthocyanins antioxidant capacity and texture of frozen/thawed blueberries. Drying resulted in reduction of total polyphenols content and antioxidant capacity (69 and 77%, respectively). The highest content of total polyphenols was noted after HACD at 90°C. Lower air temperature and prolonged exposure to oxygen resulted in greater degradation of polyphenols and antioxidant capacity. Drying processes caused a significant decrease (from 70 to 95%) in the content of anthocyanins. The highest content of anthocyanins and the strongest antioxidant capacity was found in blueberries dried using HACD at 90°C+MWVD. Among drying methods, HACD at 90°C+MWVD satisfied significant requirements for dried fruits i.e. short drying time and improved product quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

Proximate composition, total phenolic content, and antioxidant activity of seagrape (Caulerpa lentillifera).

PubMed

Nguyen, Van Tang; Ueng, Jinn-Pyng; Tsai, Guo-Jane

2011-09-01

The proximate composition of seagrape (Caulerpa lentillifera) from culture ponds in Penghu, Taiwan was analyzed. The phenolic content and the antioxidant activities including the 1,1-diphenyl-2-picryl-hydrazil (DPPH) radical scavenging activity, ferric ion-reducing activity, hydrogen peroxide scavenging activity, and ferrous ion chelating (FIC) activity of the ethanolic extracts of dry seagrape samples using 2 drying methods of freeze drying and thermal drying were compared with the ethanolic extract of Oolong tea as a reference. The contents (dry weight basis) of carbohydrate, crude protein, crude lipid, crude fiber, and ash of seagrape obtained from culture ponds in Taiwan were 64.00%, 9.26%, 1.57%, 2.97%, and 22.20%, respectively. The total phenolic content (1.30 mg gallic acid equivalent [GAE]/g dry weight) of the ethanolic extract of thermally dried seagrape was significantly lower (P < 0.05) than that (2.04 mg GAE/g dry weight) of freeze-dried seagrape, and both were significantly lower than that (13.58 mg GAE/g dry weight) of Oolong tea. At the same phenolic content, the antioxidant activities of freeze-dried seagrape were significantly higher (P < 0.05) than those of thermally dried seagrape. Compared with Oolong tea, seagrape, irrespective of drying method used, generally had strong hydrogen peroxide scavenging activity; but it was weak in DPPH radical scavenging activity, ferric ion-reducing activity, and FIC activity. The antioxidant activity of seagrape and Oolong tea was significantly influenced by their phenolic contents. The proximate composition, total phenolic content, and antioxidant activity of seagrape (Caulerpa lentillifera) in Taiwan were determined in this research to indicate nutritionally of this edible seaweed to human health, and compared these results to previous studies. © 2011 Institute of Food Technologists®

Dry coating of micronized API powders for improved dissolution of directly compacted tablets with high drug loading.

PubMed

Han, Xi; Ghoroi, Chinmay; Davé, Rajesh

2013-02-14

Motivated by our recent study showing improved flow and dissolution rate of the active pharmaceutical ingredient (API) powders (20 μm) produced via simultaneous micronization and surface modification through continuous fluid energy milling (FEM) process, the performance of blends and direct compacted tablets with high drug loading is examined. Performance of 50 μm API powders dry coated without micronization is also considered for comparison. Blends of micronized, non-micronized, dry coated or uncoated API powders at 30, 60 and 70% drug loading, are examined. The results show that the blends containing dry coated API powders, even micronized ones, have excellent flowability and high bulk density compared to the blends containing uncoated API, which are required for direct compaction. As the drug loading increases, the difference between dry coated and uncoated blends is more pronounced, as seen in the proposed bulk density-FFC phase map. Dry coating led to improved tablet compactibility profiles, corresponding with the improvements in blend compressibility. The most significant advantage is in tablet dissolution where for all drug loadings, the t(80) for the tablets with dry coated APIs was well under 5 min, indicating that this approach can produce nearly instant release direct compacted tablets at high drug loadings. Copyright © 2012 Elsevier B.V. All rights reserved.

Three-dimensional visualization and quantification of water content in the rhizosphere.

PubMed

Moradi, Ahmad B; Carminati, Andrea; Vetterlein, Doris; Vontobel, Peter; Lehmann, Eberhard; Weller, Ulrich; Hopmans, Jan W; Vogel, Hans-Jörg; Oswald, Sascha E

2011-11-01

• Despite the importance of rhizosphere properties for water flow from soil to roots, there is limited quantitative information on the distribution of water in the rhizosphere of plants. • Here, we used neutron tomography to quantify and visualize the water content in the rhizosphere of the plant species chickpea (Cicer arietinum), white lupin (Lupinus albus), and maize (Zea mays) 12 d after planting. • We clearly observed increasing soil water contents (θ) towards the root surface for all three plant species, as opposed to the usual assumption of decreasing water content. This was true for tap roots and lateral roots of both upper and lower parts of the root system. Furthermore, water gradients around the lower part of the roots were smaller and extended further into bulk soil compared with the upper part, where the gradients in water content were steeper. • Incorporating the hydraulic conductivity and water retention parameters of the rhizosphere into our model, we could simulate the gradual changes of θ towards the root surface, in agreement with the observations. The modelling result suggests that roots in their rhizosphere may modify the hydraulic properties of soil in a way that improves uptake under dry conditions. © 2011 The Authors. New Phytologist © 2011 New Phytologist Trust.

Impact of drainage on wettability of fen peat-moorsh soils

NASA Astrophysics Data System (ADS)

Szajdak, L.; Szatyłowicz, J.; Brandyk, T.

2009-04-01

High water retention in peat is attributed to structural voids (macro-pores) due to the partial degradation of the structure of peat-forming plants, and molecular absorption sites (micro-pores) associated with the formation of humic substances. Water retention by the heterogeneously-structured system in peat organic matter depends on the chemical structure of solid surfaces. These naturally wet solids, if dried sufficiently, lose the ability to rewet quickly when immersed in water. The ability of peat surfaces to attract and hold water is attributed to hydrophilic functional groups which characterize the organic substances of peat. The investigations of chemical and physical properties were performed for three different peat-moorsh soils located in the Biebrza River Valley in Poland. All examined soils were used as meadow. Soil samples were taken from two depths: 5-10 cm (moorsh) and 50-80 cm (peat). Total organic carbon (TOC), dissolved organic carbon (DOC) and humic acids (HA) extracted from these samples were analysed. Also basic physical properties such as ash content and bulk density were measured. Wetting behavior of soils was quantified using water drop penetration time test (WDPT) and measured values of the soil-water contact angle using sessile drop method. The measurements were conducted on air-dry soil samples which volumetric moisture content was not exceeding 7%. The significant differences in the concentrations of TOC, DOC and properties of HA between two investigated depth of among peat and moorsh samples were observed. The measured concentrations of total organic carbon in the considered soils ranged from 37.2 to 45.6%. Generally, the decrease of total organic carbon concentration with depth of profiles was observed. The contents of dissolved organic carbon in the soils ranged from 5.3 to 19.4%. The quantities of dissolved organic carbon decreased simultaneously with E4/E6 values and with the depth of the soil profiles. For the investigated peat's, an increase of the depth is accompanied by the decrease in the degree of humification or an increase in chemical maturity of HA. The measured values of the contact angle for investigated soils were in the range from 81.4˚ to 114.3˚ what indicates their high water repellency. The WDPT was positively correlated with total organic carbon, organic matter and humic acids content while ash content, soil bulk density, pH and absorbance were correlated negatively. The highest value of correlation coefficient (statistically significant) was obtained for relation between WDPT and ash content. The soil water contact angle was less correlated with peat-moorsh soil properties in comparison with WDPT with one exception pH. The pH against the contact angle indicates tendency of increasing the contact angle with decreasing pH.

Low temperature hot air drying of potato cubes subjected to osmotic dehydration and intermittent microwave: drying kinetics, energy consumption and product quality indexes

NASA Astrophysics Data System (ADS)

Dehghannya, Jalal; Bozorghi, Somayyeh; Heshmati, Maryam Khakbaz

2018-04-01

Hot-air drying is a slow energy-extensive process. Use of intermittent microwave (IM) in hot-air (HA) drying of food products is characterized with advantages including reduced process time, energy saving, and improved final quality. In this study, the effect of IM-HA drying following an osmotic dehydration (OD) pretreatment was analyzed on qualitative and quantitative properties of the output (i.e. effective moisture diffusion coefficient (Deff), shrinkage, bulk density, rehydration and energy consumption). Temperature and airflow velocity were fixed at 40°C and 1 m/s, respectively. The process variables included sucrose solution concentration at five levels (0 or control, 10, 30, 50 and 70 w/w%), microwave output power at four levels (0 or control, 360, 600 and 900 W), and pulse ratio at four levels (1, 2, 3 and 4). Use of osmotic dehydration in combination with IM-HA drying reduced the drying time by up to about 54%. Increasing the osmotic solution concentration to 30% and using higher pulse ratios increased the Deff. The lowest shrinkage and bulk density as well as the highest rehydration belonged to the 900 W microwave power and pulse ratio of 4. The lowest energy consumption was observed when using the 900 W power level, showing 63.27% less consumption than the HA drying method.

A study on friability, hardness and fiber content analysis of fiber enriched milk tablet

NASA Astrophysics Data System (ADS)

Suzihaque, M. U. H.; Irfan, M. H.; Ibrahim, U. K.

2017-06-01

This study was performed to analyze the friability, hardness and fiber content of fiber enriched milk tablet derived from five different local fiber sources such as carrot, spinach, dragon fruit, mango and watermelon. Cow milk was mixed to complement with the tablet as a protein source. The powder were spray dried at 100°C, 120°C and 140°C and freeze dried at -60°C. The mixture of fruits and milk were made into equal ratio with the addition of 15 maltodextrin as a carrier. Tablets formed were used for friability and hardness test while dried powder were used for fiber content analysis. Dragon fruit tablet dried at 140°C have the highest friability with 11. 42 of weight loss. The second highest friability was spinach tablet dried at 100°C and 120°C drying temp erature with 9.30 and 9.28 respectively. The lowest friability was exhibited by carrot, mango and watermelon tablet at 100°C and dragon fruit at 120°C while carrot and spinach at 140°C. In contras t, none of the freeze dried tablets showed any weight loss hence they are not friable. For hardness test, all of the freeze dried showed to have higher tensile strength than spray dried, where carrot showed to be the highest at 2.27 Newton and the lowest were spray dried mango at 0.16 Newton. In fiber content analysis, freeze dried mango have the highest fiber content followed by freeze dried carrot and 140°C s pray dried carrot. It can be concluded that the higher the spray dry temperature, the more friable is the tablet. While, high friability leads to lower hardness of tablets. In terms of fiber content, the higher the spray dry temperature, the lower the fiber content found.

Carbon stable isotopic composition of soluble sugars in Tillandsia epiphytes varies in response to shifts in habitat.

PubMed

Goode, Laurel K; Erhardt, Erik B; Santiago, Louis S; Allen, Michael F

2010-07-01

We studied C stable isotopic composition (delta(13)C) of bulk leaf tissue and extracted sugars of four epiphytic Tillandsia species to investigate flexibility in the use of crassulacean acid metabolism (CAM) and C(3) photosynthetic pathways. Plants growing in two seasonally dry tropical forest reserves in Mexico that differ in annual precipitation were measured during wet and dry seasons, and among secondary, mature, and wetland forest types within each site. Dry season sugars were more enriched in (13)C than wet season sugars, but there was no seasonal difference in bulk tissues. Bulk tissue delta(13)C differed by species and by forest type, with values from open-canopied wetlands more enriched in (13)C than mature or secondary forest types. The shifts within forest habitat were related to temporal and spatial changes in vapor pressure deficits (VPD). Modeling results estimate a possible 4% increase in the proportional contribution of the C(3) pathway during the wet season, emphasizing that any seasonal or habitat-mediated variation in photosynthetic pathway appears to be quite moderate and within the range of isotopic effects caused by variation in stomatal conductance during assimilation through the C(3) pathway and environmental variation in VPD. C isotopic analysis of sugars together with bulk leaf tissue offers a useful approach for incorporating short- and long-term measurements of C isotope discrimination during photosynthesis.

Carbon stable isotopic composition of soluble sugars in Tillandsia epiphytes varies in response to shifts in habitat

PubMed Central

Erhardt, Erik B.; Santiago, Louis S.; Allen, Michael F.

2010-01-01

We studied C stable isotopic composition (δ13C) of bulk leaf tissue and extracted sugars of four epiphytic Tillandsia species to investigate flexibility in the use of crassulacean acid metabolism (CAM) and C3 photosynthetic pathways. Plants growing in two seasonally dry tropical forest reserves in Mexico that differ in annual precipitation were measured during wet and dry seasons, and among secondary, mature, and wetland forest types within each site. Dry season sugars were more enriched in 13C than wet season sugars, but there was no seasonal difference in bulk tissues. Bulk tissue δ13C differed by species and by forest type, with values from open-canopied wetlands more enriched in 13C than mature or secondary forest types. The shifts within forest habitat were related to temporal and spatial changes in vapor pressure deficits (VPD). Modeling results estimate a possible 4% increase in the proportional contribution of the C3 pathway during the wet season, emphasizing that any seasonal or habitat-mediated variation in photosynthetic pathway appears to be quite moderate and within the range of isotopic effects caused by variation in stomatal conductance during assimilation through the C3 pathway and environmental variation in VPD. C isotopic analysis of sugars together with bulk leaf tissue offers a useful approach for incorporating short- and long-term measurements of C isotope discrimination during photosynthesis. PMID:20155286

The Effect of Operating Conditions on Drying Characteristics and Quality of Ginger (Zingiber Officinale Roscoe) Using Combination of Solar Energy-Molecular Sieve Drying System

NASA Astrophysics Data System (ADS)

Hasibuan, R.; Zamzami, M. A.

2017-03-01

Ginger (Zingiber officinale Roscoe) is an agricultural product that can be used as beverages and snacks, and especially for traditional medicines. One of the important stages in the processing of ginger is drying. The drying process intended to reduce the water content of 85-90% to 8-10%, making it safe from the influence of fungi or insecticide. During the drying takes place, the main ingredient contained in ginger is homologous ketone phenolic known as gingerol are chemically unstable at high temperatures, for the drying technology is an important factor in maintaining the active ingredient (gingerol) which is in ginger. The combination of solar energy and molecular sieve dryer that are used in the research is capable of operating 24 hours. The purpose of this research is to study the effect of operating conditions (in this case the air velocity) toward the drying characteristics and the quality of dried ginger using the combination of solar energy and molecular sieve dryer. Drying system consist of three main parts which is: desiccator, solar collector, and the drying chamber. To record data changes in the mass of the sample, a load cell mounted in the drying chamber, and then connected to the automated data recording system using a USB data cable. All data of temperature and RH inside the dryer box and the change of samples mass recorded during the drying process takes place and the result is stored in the form of Microsoft Excel. The results obtained, shows that the air velocity is influencing the moisture content and ginger drying rate, where the moisture content equilibrium of ginger for the air velocity of 1.3 m/s was obtained on drying time of 360 minutes and moisture content of 2.8%, at 1.0 m/s was obtained on drying time of 300 minutes and moisture content of 1.4%, at 0, 8 m/s was obtained at 420 minutes drying time and the moisture content is 2.0%. The drying characteristics shows that there are two drying periods, which is: the increasing drying rate, and the falling drying rate, while the constant drying rate is not visible. The result of ginger quality shows that there are no significant changes in the organoleptic analysis, the ash content is about 7.52-7.94% and the oil content is 0.79-0.83%.

From dry to saturated thermal conductivity: mixing-model correction charts and new conversion equations for sedimentary rocks

NASA Astrophysics Data System (ADS)

Fuchs, Sven; Schütz, Felina; Förster, Andrea; Förster, Hans-Jürgen

2013-04-01

The thermal conductivity (TC) of a rock is, in collaboration with the temperature gradient, the basic parameter to determine the heat flow from the Earth interior. Moreover, it forms the input into models targeted on temperature prognoses for geothermal reservoirs at those depths not yet reached by boreholes. Thus, rock TC is paramount in geothermal exploration and site selection. Most commonly, TC of a rock is determined in the laboratory on samples that are either dry or water-saturated. Because sample saturation is time-consuming, it is desirable, especially if large numbers of samples need to be assessed, to develop an approach that quickly and reliably converts dry-measured bulk TC into the respective saturated value without applying the saturation procedure. Different petrophysical models can be deployed to calculate the matrix TC of a rock from the bulk TC and vice versa, if the effective porosity is known (e.g., from well logging data) and the TC of the saturation fluid (e.g., gas, oil, water) is considered. We have studied for a large suite of different sedimentary rocks the performance of two-component (rock matrix, porosity) models that are widely used in geothermics (arithmetic mean, geometric mean, harmonic mean, Hashin and Shtrikman mean, and effective medium theory mean). The data set consisted of 1147 TC data from three different sedimentary basins (North German Basin, Molasse Basin, Mesozoic platform sediments of the northern Sinai Microplate in Israel). Four lithotypes (sandstone, mudstone, limestone, dolomite) were studied exhibiting bulk TC in the range between 1.0 and 6.5 W/(mK). The quality of fit between measured (laboratory) and calculated bulk TC values was studied separately for the influence of lithotype, saturation fluid (water and isooctane), and rock anisotropy (parallel and perpendicular to bedding). The geometric mean model displays the best correspondence between calculated and measured bulk TC, however, the relation is not satisfying. To improve the fit of the models, correction equations are calculated based on the statistical data. In addition, the application of correction equations allows a significant improvement of the accuracy of bulk TC data calculated. However, the "corrected" geometric mean constitutes the only model universally applicable to different types of sedimentary rocks and, thus, is recommended for the calculation of bulk TC. Finally, the statistical analysis also resulted in lithotype-specific conversion equations, which permit a calculation of the water-saturated bulk TC from dry-measured TC and porosity (e.g., well-log-derived porosity). This approach has the advantage that the saturated bulk TC could be calculated readily without application of any mixing model. The expected errors with this approach are in the range between 5 and 10 % (Fuchs et al., 2013).

Implications of genetic selection on yolk proportion on the dry matter content of eggs in a White Leghorn population.

PubMed

Icken, W; Looft, C; Schellander, K; Cavero, D; Blanco, A; Schmutz, M; Preisinger, R

2014-01-01

1. The responses to genetic selection on yolk proportion as a technique for increasing egg dry matter content, an important criterion for the egg-product industry, was investigated in a pedigree flock of White Leghorn hens. 2. Parents were preselected on high and low yolk proportion from a base population. The absolute estimated breeding value for yolk proportion of both groups differed by 3%. The realised selection difference in dry matter content of eggs between groups was more than 1% in the analysed offspring population. 3. Heritability estimates were moderate and dry matter had a lower heritability (h(2) = 0.39) than yolk proportion (h(2) = 0.44). 4. The genetic correlation between yolk proportion and dry matter content was highly positive (rg = 0.91). Genetic correlations with egg weight were negative and would have to be compensated for in a breeding programme (rg = -0.76 with yolk proportion and rg = -0.64 with dry matter content). The genetic correlation between the laying performance and yolk proportion was rg = 0.28 and close to zero (rg = -0.05) for dry matter content. 5. Easy recording and lower undesirable correlations make yolk proportion more suitable for commercial selection compared with egg dry matter content in layer breeding.

Using 13C labeled glucose to determine soil microbial and physical controls of new C incorporation under drying-rewetting cycles and conservation agricultural management

NASA Astrophysics Data System (ADS)

Li, L.; Schaeffer, S. M.

2017-12-01

Drying-rewetting cycles can induce carbon (C) depletion in soil, while conservation agricultural management aims at soil C sequestration. Understanding the combined effect of drying-rewetting cycles and conservation management is critical for sustaining agricultural soil under climate change. Soil organic C can be stored in a relatively rapidly cycling active pool, or a more slowly cycling passive pool. We conducted a 24-days mesocosm incubation using an agricultural soil from western Tennessee under 35-years of conservation management. Different lengths of drought period before rewetting of 0, 3, 6, and 24 days were applied on the mesocosms. To trace the fate of newly added C, 13C labeled glucose was added to the mesocosms at the beginning of the incubation. After 24 days, dissolvable organic C, microbial biomass C, accumulative microbial respiration, and extracellular enzyme activity were analyzed to evaluate the active C pool; hydrogen peroxide oxidation and aggregate size fractionation were used to examine the passive C pool. The highest cumulative microbial respiration was found in the 6-days treatment combining a N-fixing cover crop with no-tillage, and the lowest in the 24-day treatment with a wheat cover crop combined with conventional-tillage (1000.0±20.5 and 106.8±17.5 µg C-CO2 g-1 dry soil, respectively). The 6-days treatment induced 0.5-4.3 times higher cumulative C-CO2 emission than the 3-days treatment. The proportion of macroaggregates in bulk soil varied between 97.2% and 76.7%, and it was negatively correlated with drying-rewetting frequency. The proportion of microaggregates in bulk soil varied between 21.9% and 2.1%, and it was positively correlated with drying-rewetting frequency. 13C recovery rate in bulk soil varied between 11-53%. The vetch-cover-crop-with-no-tillage treatment facilitated 13C accumulation the most. Our results show that the N fixing cover crops combined with no-tillage treatment induced the highest C accumulation in bulk soil, while the no cover crop combined with conventional tillage induced the lowest C concentration. Our results show that frequent drying-rewetting cycles disrupt macroaggregates and release the microaggregates within macroaggregates, and favor greater C loss combined with greater C storage in less stable aggregate fractions.

46 CFR 151.50-31 - Chlorine.

Code of Federal Regulations, 2014 CFR

2014-10-01

... force the liquid out of the tank, compressed air, or other nonreactive gas, may be used to secure the desired rate of discharge, provided the air or gas is oil-free and thoroughly dried by passing it over... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES BARGES CARRYING BULK...

46 CFR 151.50-31 - Chlorine.

Code of Federal Regulations, 2012 CFR

2012-10-01

... force the liquid out of the tank, compressed air, or other nonreactive gas, may be used to secure the desired rate of discharge, provided the air or gas is oil-free and thoroughly dried by passing it over... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES BARGES CARRYING BULK...

46 CFR 151.50-31 - Chlorine.

Code of Federal Regulations, 2013 CFR

2013-10-01

... force the liquid out of the tank, compressed air, or other nonreactive gas, may be used to secure the desired rate of discharge, provided the air or gas is oil-free and thoroughly dried by passing it over... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES BARGES CARRYING BULK...

46 CFR 154.412 - Cargo tank corrosion allowance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... allowance if the cargo tank: (a) is located in a space that does not have inert gas or dry air; or (b... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo...

46 CFR 154.412 - Cargo tank corrosion allowance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... allowance if the cargo tank: (a) is located in a space that does not have inert gas or dry air; or (b... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo...

46 CFR 154.412 - Cargo tank corrosion allowance.

Code of Federal Regulations, 2013 CFR

2013-10-01

... allowance if the cargo tank: (a) is located in a space that does not have inert gas or dry air; or (b... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo...

The Water Content of Exo-earths in the Habitable Zone around Low-mass Stars

NASA Astrophysics Data System (ADS)

Mulders, Gijs Dirk; Ciesla, Fred; Pascucci, Ilaria; apai, Daniel

2015-08-01

Terrestrial planets in the habitable zones of low-mass M dwarf stars have become the focus of many astronomical studies: they are more easily accessible to detection and characterization than their counterparts around sunlike stars. The habitability of these planets, however, faces a number of challenges, including inefficient or negligible water delivery during accretion. To understand the water content of planets in and around the habitable zone, simulations of the final stages of planet formation are necessary.We present detailed accretion simulations of wet and dry planetary embryos around a range of stellar masses. We focus on different pathways of delivering water from beyond the snow line to terrestrial planets in the habitable zone. We explore the impact of using either asteroid-like or comet-like bodies, and the effects of a dispersion in snow line locations. We derive the probability distribution of water abundances for terrestrial sized planets in the habitable zone.While these models predict that the bulk of terrestrial planets in the habitable zones of M stars will be dry, a small fraction receives earth-like amounts of water. Given their larger numbers and higher planet occurrence rates, this population of water-enriched worlds in the habitable zone of M stars may equal that around sun-like stars in numbers.References:Ciesla, Mulders et al. 2015Mulders et al. ApJ subm.

Percolation and transport in a sandy soil under a natural hydraulic gradient

USGS Publications Warehouse

Green, Christopher T.; Stonestrom, David A.; Bekins, Barbara A.; Akstin, Katherine C.; Schulz, Marjorie S.

2005-01-01

Unsaturated flow and transport under a natural hydraulic gradient in a Mediterranean climate were investigated with a field tracer experiment combined with laboratory analyses and numerical modeling. Bromide was applied to the surface of a sandy soil during the dry season. During the subsequent rainy season, repeated sediment sampling tracked the movement of bromide through the profile. Analysis of data on moisture content, matric pressure, unsaturated hydraulic conductivity, bulk density, and soil texture and structure provides insights into parameterization and use of the advective‐dispersive modeling approach. Capturing the gross features of tracer and moisture movement with model simulations required an order‐of‐magnitude increase in laboratory‐measured hydraulic conductivity. Wetting curve characteristics better represented field results, calling into question the routine estimation of hydraulic characteristics based only on drying conditions. Measured increases in profile moisture exceeded cumulative precipitation in early winter, indicating that gains from dew drip can exceed losses from evapotranspiration during periods of heavy (“Tule”) fog. A single‐continuum advective‐dispersive modeling approach could not reproduce a peak of bromide that was retained near the soil surface for over 3 years. Modeling of this feature required slow exchange of solute at a transfer rate of 0.5–1 × 10−4 d−1 with an immobile volume approaching the residual moisture content.

Effects of biochars on hydraulic properties of clayey soil

NASA Astrophysics Data System (ADS)

Zhen, Jingbo; Palladino, Mario; Lazarovitch, Naftali; Bonanomi, Giuliano; Battista Chirico, Giovanni

2017-04-01

Biochar has gained popularity as an amendment to improve soil hydraulic properties. Since biochar properties depend on feedstocks and pyrolysis temperatures used for its production, proper selection of biochar type as soil amendment is of great importance for soil hydraulic properties improvement. This study investigated the effects of eight types of biochar on physical and hydraulic properties of clayey soil. Biochars were derived from four different feedstocks (Alfalfa hay, municipal organic waste, corn residues and wood chip) pyrolyzed at two different temperatures (300 and 550 °C). Clayey soil samples were taken from Leone farm (40° 26' 15.31" N, 14° 59' 45.54" E), Italy, and were oven-dried at 105 °C to determine dry bulk density. Biochars were mixed with the clayey soil at 5% by mass. Bulk densities of the mixtures were also determined. Saturated hydraulic conductivities (Ks) of the original clayey soil and corresponding mixtures were measured by means of falling-head method. Soil water retention measurements were conducted for clayey soil and mixtures using suction table apparatus and Richards' plate with the pressure head (h) up to 12000 cm. van Genuchten retention function was selected to evaluate the retention characteristics of clayey soil and mixtures. Available water content (AWC) was calculated by field capacity (h = - 500 cm) minus wilting pointing (h = -12000 cm). The results showed that biochar addition decreased the bulk density of clayey soil. The Ks of clayey soil increased due to the incorporation of biochars except for waste and corn biochars pyrolyzed at 550 °C. AWC of soils mixed with corn biochar pyrolyzed at 300 °C and wood biochar pyrolyzed at 550 °C, increased by 31% and 7%, respectively. Further analysis will be conducted in combination of biochar properties such as specific surface area and total pore volume. Better understanding of biochar impact on clayey soil will be helpful in biochar selection for soil amendment and improving water use efficiency in agriculture.

[Comparison of sulfur fumigation processing and direct hot air heating technology on puerarin contents and efficacy of Puerariae Thomsonii Radix].

PubMed

Yu, Hong-Li; Zhang, Qian; Jin, Yang-Ping; Wang, Kui-Long; Lu, Tu-Lin; Li, Lin

2016-07-01

In order to compare the effect of sulfur fumigation processing and direct hot air heating technology on puerarin contents and efficacy of Puerariae Thomsonii Radix, the fresh roots of Pueraria thomsonii were cut into small pieces and prepared into direct sunshine drying samples, direct hot air drying samples, and sulfur fumigation-hot air drying samples. Moisture contents of the samples were then determined. The puerarin contents of different samples were compared by HPLC method. Moreover, the models of drunkenness mice were established, and then with superoxide dismutase (SOD) content as the index, aqueous decoction extracts of Puerariae Thomsonii Radix samples with sulfur fumigation processing and non-sulfur fumigation processing methods were administrated by ig; the effects of sulfur fumigation on contents of SOD in mice liver and serum were determined, and the sulfur fumigation samples and non-sulfur fumigation samples were investigated for moth and mildew under different packaging and storage conditions. Results showed that the sulfur fumigation samples significantly changed the puerarin content from Puerariae Thomsonii Radix. The content of puerarin was decreased gradually when increasing the times of sulfur fumigation and amount of sulfur. SOD content in drunken mice liver and serum was significantly decreased when increasing the times of sulfur fumigation, showing significant difference with both direct sunshine drying group and direct hot air drying group. Moth and mildew were not found in the sulfur fumigation samples and direct hot air drying samples whose moisture contents were lower than the limit in Pharmacopoeia. Research showed that sulfur fumigation can significantly reduce the content of main active ingredients and reduce the efficacy of Puerariae Thomsonii Radix, indicating that the quality of Puerariae Thomsonii Radix was significantly decreased after sulfur fumigation. However, the contents of the main active ingredients, efficacy and storage results of the direct hot air drying samples were similar to those in direct sunshine drying samples, so the hot air drying process was a nice drying technology which could be promoted for use. Copyright© by the Chinese Pharmaceutical Association.

[Investigation on Spray Drying Technology of Auricularia auricular Extract].

PubMed

Zhou, Rong; Chen, Hui; Xie, Yuan; Chen, Peng; Wang, Luo-lin

2015-07-01

To investigate the feasibility of spray drying technology of Auricularia auricular extract and its optimum process. On the basis of single factor test, with the yield of dry extract and the content of polysaccharide as indexes, orthogonal test method was used to optimize the spray drying technology on the inlet air temperature, injection speed and crude drug content. Using ultraviolet spectrophotometry, thin layer chromatography(TLC) and pharmacodynamics as indicators, extracts prepared by traditional alcohol precipitation drying process and spray drying process were compared. Compared with the traditional preparation method, the extract prepared by spray drying had little differences from the polysaccharide content, TLC and the function of reducing TG and TC, and its optimum technology condition were as follows: The inlet air temperature was 180 °C, injection speed was 10 ml/min and crude drugs content was 0. 4 g/mL. Auricularia auricular extract by spray drying technology is stable and feasible with high economic benefit.

Dewatering treatments to increase dry matter content of the brown seaweed, kelp (Laminaria digitata ((Hudson) JV Lamouroux)).

PubMed

Gallagher, Joe A; Turner, Lesley B; Adams, Jessica M M; Dyer, Philip W; Theodorou, Michael K

2017-01-01

Macroalgal water content is an on-going problem for the use of readily accessible seaweeds in sustainable biorefining, including fuel production. Silage is a reduced-water, compactable, easily stored, transportable material. Ensiling could establish a non-seasonal supply of preserved algal biomass, but requires high initial dry matter content to mitigate environmental pollution risks from effluent. This study investigated potential dewatering methods for kelp harvested throughout the year. Treatments included air-drying, osmotic media and acids. Significant interactions between treatment and harvest-time were observed for traits of interest. Fresh weight loss during treatment was composed of changes in water and dry matter content. Air-drying gave reliable increase in final dry matter content; in summer and autumn 30% dry matter content was reached after 24h. Dilute hydrochloric acid reduced stickiness and rendered material suitable for dewatering by screw-pressing; it may be possible to use the consequent pH reduction to promote efficient preservation. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The effect of residual water on antacid properties of sucralfate gel dried by microwaves.

PubMed

Gainotti, Alessandro; Losi, Elena; Colombo, Paolo; Santi, Patrizia; Sonvico, Fabio; Baroni, Daniela; Massimo, Gina; Colombo, Gaia; Del Gaudio, Pasquale

2006-01-20

The aim of this work was to study the acid neutralization characteristics of microwave-dried sucralfate gel in relation to the water content and physical structure of the substance. Several dried sucralfate gels were compared with humid sucralfate gel and sucralfate nongel powder in terms of neutralization rate and buffering capacity. Humid sucralfate gel and microwave-dried gel exhibited antacid effectiveness. In particular, the neutralization rate of dried gel powders was inversely related to the water content: as the water content of dried powders decreased, the acid reaction rate linearly increased. The relationship was due to the different morphology of dried sucralfate gels. In fact, the porosity of the dried samples increased with the water reduction. However, the acid neutralization equivalent revealed that the dried sucralfate gel became more resistant to acid attack in the case of water content below 42%. Then, the microwave drying procedure had the opposite effect on the reactivity of the aluminum hydroxide component of dried sucralfate gel powders, since the rate of the reaction increased whereas the buffering capacity decreased as the amount of water was reduced.

The effect of residual water on antacid properties of sucralfate gel dried by microwaves.

PubMed

Gainotti, Alessandro; Losi, Elena; Colombo, Paolo; Santi, Patrizia; Sonvico, Fabio; Baroni, Daniela; Massimo, Gina; Colombo, Gaia; Del Gaudio, Pasquale

2006-03-01

The aim of this work was to study the acid neutralization characteristics of microwave-dried sucralfate gel in relation to the water content and physical structure of the substance. Several dried sucralfate gels were compared with humid sucralfate gel and sucralfate nongel powder in terms of neutralization rate and buffering capacity. Humid sucralfate gel and microwave-dried gel exhibited antacid effectiveness. In particular, the neutralization rate of dried gel powders was inversely related to the water content: as the water content of dried powders decreased, the acid reaction rate linearly increased. The relationship was due to the different morphology of dried sucralfate gels. In fact, the porosity of the dried samples increased with the water reduction. However, the acid neutralization equivalent revealed that the dried sucralfate gel became more resistant to acid attack in the case of water content below 42%. Then, the microwave drying procedure had the opposite effect on the reactivity of the aluminum hydroxide component of dried sucralfate gel powders, since the rate of the reaction increased whereas the buffering capacity decreased as the amount of water was reduced.

Characterization and identification of ISSR markers associated with oil content in sea buckthorn berries.

PubMed

Ding, J; Ruan, C J; Guan, Y; Shan, J Y; Li, H; Bao, Y H

2016-08-19

Bioactive oils extracted from sea buckthorn (Hippophae rhamnoides) berries contain highly nutritional and medicinal compounds; however, the oil contents of sea buckthorn berries are very low. Thirteen inter-simple sequence repeat (ISSR) primers were used to identify markers associated with oil content of dry pulp in 51 cultivars and lines, which clustered into three major groups based on 137 polymorphic markers. Dry pulp oil contents in 45 cultivars and lines in Group I ranged from 6.6 to 33.1%; these accessions belonged to H. rhamnoides ssp mongolica and its hybrids with H. rhamnoides ssp sinensis. Three lines (H. rhamnoides ssp mongolica) in Group II had high dry pulp oil contents (33.7 to 37.5%), whereas three lines of hybrids in Group III had low dry pulp oil contents (10.9 to 17.5%). The dry pulp oil content of H. rhamnoides ssp mongolica (27.2 ± 0.9%) was higher than that of hybrids (12.0 ± 1.2%) (P < 0.01). Four ISSR markers (881 340 , 825 1000 , 817 380 , and 807 1100 ) had positive association with high dry pulp oil content (P < 0.01) using stepwise multiple regression analysis. The use of these ISSR markers is a potential strategy to select genotypes with high dry pulp oil content and suitable parental combinations for improvement of sea buckthorn berries.

Thermal Flammable Gas Production from Bulk Vitrification Feed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheele, Randall D.; McNamara, Bruce K.; Bagaasen, Larry M.

2008-05-21

The baseline bulk-vitrification (BV) process (also known as in-container vitrification ICV™) includes a mixer/dryer to convert liquid low-activity waste (LAW) into a dried, blended feed for vitrification. Feed preparation includes blending LAW with glass-forming minerals (GFMs) and cellulose and drying the mixture to a suitable dryness, consistency, and particle size for transport to the ICVTM container. The cellulose is to be added to the BV feed at a rate sufficient to destroy 75% of the nitrogen present as nitrate or nitrite. Concern exists that flammable gases may be produced during drying operations at levels that could pose a risk. Themore » drying process is conducted under vacuum in the temperature range of 60 to 80°C. These flammable gases could be produced either through thermal decomposition of cellulose or waste organics or as a by-product of the reaction of cellulose and/or waste organics with nitrate or the postulated small amount of nitrite present in the waste. To help address the concern about flammable gas production during drying, the Pacific Northwest National Laboratory (PNNL) performed studies to identify the gases produced at dryer temperatures and at possible process upset conditions. Studies used a thermogravimetric analyzer (TGA) up to 525°C and isothermal testing up to 120°C to determine flammable gas production resulting from the cellulose and organic constituents in bulk vitrification feed. This report provides the results of those studies to determine the effects of cellulose and waste organics on flammable gas evolution« less

Effect of drying of figs (Ficus carica L.) on the contents of sugars, organic acids, and phenolic compounds.

PubMed

Slatnar, Ana; Klancar, Urska; Stampar, Franci; Veberic, Robert

2011-11-09

Fresh figs were subjected to two different drying processes: sun-drying and oven-drying. To assess their effect on the nutritional and health-related properties of figs, sugars, organic acids, single phenolics, total phenolics, and antioxidant activity were determined before and after processing. Samples were analyzed three times in a year, and phenolic compounds were determined using high-performance liquid chromatography coupled with mass spectrometry (HPLC-MS). In figs, monomer sugars predominate, which is important nutritional information, and the content of sugars as well as organic acids in fresh figs was lower than in dried fruits. However, the best sugar/organic acid ratio was measured after the sun-drying process. Analysis of individual phenolic compounds revealed a higher content of all phenolic groups determined after the oven-drying process, with the exception of cyanidin-3-O-rutinoside. Similarly, higher total phenolic content and antioxidant activity were detected after the drying process. With these results it can be concluded that the differences in analyzed compounds in fresh and dried figs are significant. The differences between the sun-dried and oven-dried fruits were determined in organic acids, sugars, chlorogenic acid, catechin, epicatechin, kaempferol-3-O-glucoside, luteolin-8-C-glucoside, and total phenolic contents. The results indicate that properly dried figs can be used as a good source of phenolic compounds.

The effect of drying temperatures on antioxidant activity, phenolic compounds, fatty acid composition and tocopherol contents in citrus seed and oils.

PubMed

Al Juhaimi, Fahad; Özcan, Mehmet Musa; Uslu, Nurhan; Ghafoor, Kashif

2018-01-01

In this study, the effect of drying temperature on antioxidant activity, phenolic compounds, fatty acid composition and tocopherol content of citrus seeds and oils were studied. Kinnow mandarin seed, dried at 60 °C, exhibited the highest antioxidant activity. Orlendo orange seed had the maximum total phenolic content and α-tocopherol content, with a value of 63.349 mg/100 g and 28.085 mg/g (control samples), respectively. The antioxidant activity of Orlendo orange seed (63.349%) was higher than seeds of Eureka lemon (55.819%) and Kinnow mandarin (28.015%), while the highest total phenolic content was found in seeds of Kinnow mandarin, followed by Orlendo orange and Eureka lemon (113.132). 1.2-Dihydroxybenzene (13.171), kaempferol (10.780), (+)-catechin (9.341) and isorhamnetin (7.592) in mg/100 g were the major phenolic compounds found in Kinnow mandarin. Among the unsaturated fatty acids, linoleic acid was the most abundant acid in all oils, which varied from 44.4% (dried at 80 °C) to 46.1% (dried at 70 °C), from 39.0% (dried at 60 °C) to 40.0% (dried at 70 °C). The total phenolic content, antioxidant activity and phenolic compounds of citrus seeds and tocopherol content of seed oils were significantly affected by drying process and varied depending on the drying temperature.

Methane Exchange in a Coastal Fen in the First Year after Flooding - A Systems Shift

PubMed Central

Hahn, Juliane; Köhler, Stefan; Glatzel, Stephan; Jurasinski, Gerald

2015-01-01

Background Peatland restoration can have several objectives, for example re-establishing the natural habitat, supporting unique biodiversity attributes or re-initiating key biogeochemical processes, which can ultimately lead to a reduction in greenhouse gas (GHG) emissions. Every restoration measure, however, is itself a disturbance to the ecosystem. Methods Here, we examine an ecosystem shift in a coastal fen at the southern Baltic Sea which was rewetted by flooding. The analyses are based on one year of bi-weekly closed chamber measurements of methane fluxes gathered at spots located in different vegetation stands. During measurement campaigns, we recorded data on water levels, peat temperatures, and chemical properties of peat water. In addition we analyzed the first 20 cm of peat before and after flooding for dry bulk density (DBD), content of organic matter and total amounts of carbon (C), nitrogen (N), sulfur (S), and other nutrients. Results Rewetting turned the site from a summer dry fen into a shallow lake with water levels up to 0.60 m. We observed a substantial die-back of vegetation, especially in stands of sedges (Carex acutiformis Ehrh). Concentrations of total organic carbon and nitrogen in the peat water, as well as dry bulk density and concentrations of C, N and S in the peat increased. In the first year after rewetting, the average annual exchange of methane amounted to 0.26 ± 0.06 kg m-2. This is equivalent to a 190-times increase in methane compared to pre-flooding conditions. Highest methane fluxes occurred in sedge stands which suffered from the heaviest die-back. None of the recorded environmental variables showed consistent relationships with the amounts of methane exchanged. Conclusions Our results suggest that rewetting projects should be monitored not only with regard to vegetation development but also with respect to biogeochemical conditions. Further, high methane emissions that likely occur directly after rewetting by flooding should be considered when forecasting the overall effect of rewetting on GHG exchange. PMID:26461916

Methane Exchange in a Coastal Fen in the First Year after Flooding--A Systems Shift.

PubMed

Hahn, Juliane; Köhler, Stefan; Glatzel, Stephan; Jurasinski, Gerald

2015-01-01

Peatland restoration can have several objectives, for example re-establishing the natural habitat, supporting unique biodiversity attributes or re-initiating key biogeochemical processes, which can ultimately lead to a reduction in greenhouse gas (GHG) emissions. Every restoration measure, however, is itself a disturbance to the ecosystem. Here, we examine an ecosystem shift in a coastal fen at the southern Baltic Sea which was rewetted by flooding. The analyses are based on one year of bi-weekly closed chamber measurements of methane fluxes gathered at spots located in different vegetation stands. During measurement campaigns, we recorded data on water levels, peat temperatures, and chemical properties of peat water. In addition we analyzed the first 20 cm of peat before and after flooding for dry bulk density (DBD), content of organic matter and total amounts of carbon (C), nitrogen (N), sulfur (S), and other nutrients. Rewetting turned the site from a summer dry fen into a shallow lake with water levels up to 0.60 m. We observed a substantial die-back of vegetation, especially in stands of sedges (Carex acutiformis Ehrh). Concentrations of total organic carbon and nitrogen in the peat water, as well as dry bulk density and concentrations of C, N and S in the peat increased. In the first year after rewetting, the average annual exchange of methane amounted to 0.26 ± 0.06 kg m-2. This is equivalent to a 190-times increase in methane compared to pre-flooding conditions. Highest methane fluxes occurred in sedge stands which suffered from the heaviest die-back. None of the recorded environmental variables showed consistent relationships with the amounts of methane exchanged. Our results suggest that rewetting projects should be monitored not only with regard to vegetation development but also with respect to biogeochemical conditions. Further, high methane emissions that likely occur directly after rewetting by flooding should be considered when forecasting the overall effect of rewetting on GHG exchange.

Physical Quality Indicators and Mechanical Behavior of Agricultural Soils of Argentina.

PubMed

Imhoff, Silvia; da Silva, Alvaro Pires; Ghiberto, Pablo J; Tormena, Cássio A; Pilatti, Miguel A; Libardi, Paulo L

2016-01-01

Mollisols of Santa Fe have different tilth and load support capacity. Despite the importance of these attributes to achieve a sustainable crop production, few information is available. The objectives of this study are i) to assess soil physical indicators related to plant growth and to soil mechanical behavior; and ii) to establish relationships to estimate the impact of soil loading on the soil quality to plant growth. The study was carried out on Argiudolls and Hapludolls of Santa Fe. Soil samples were collected to determine texture, organic matter content, bulk density, water retention curve, soil resistance to penetration, least limiting water range, critical bulk density for plant growth, compression index, pre-consolidation pressure and soil compressibility. Water retention curve and soil resistance to penetration were linearly and significantly related to clay and organic matter (R2 = 0.91 and R2 = 0.84). The pedotransfer functions of water retention curve and soil resistance to penetration allowed the estimation of the least limiting water range and critical bulk density for plant growth. A significant nonlinear relationship was found between critical bulk density for plant growth and clay content (R2 = 0.98). Compression index was significantly related to bulk density, water content, organic matter and clay plus silt content (R2 = 0.77). Pre-consolidation pressure was significantly related to organic matter, clay and water content (R2 = 0.77). Soil compressibility was significantly related to initial soil bulk density, clay and water content. A nonlinear and significantly pedotransfer function (R2 = 0.88) was developed to predict the maximum acceptable pressure to be applied during tillage operations by introducing critical bulk density for plant growth in the compression model. The developed pedotransfer function provides a useful tool to link the mechanical behavior and tilth of the soils studied.

Physical Quality Indicators and Mechanical Behavior of Agricultural Soils of Argentina

PubMed Central

Pires da Silva, Alvaro; Ghiberto, Pablo J.; Tormena, Cássio A.; Pilatti, Miguel A.; Libardi, Paulo L.

2016-01-01

Mollisols of Santa Fe have different tilth and load support capacity. Despite the importance of these attributes to achieve a sustainable crop production, few information is available. The objectives of this study are i) to assess soil physical indicators related to plant growth and to soil mechanical behavior; and ii) to establish relationships to estimate the impact of soil loading on the soil quality to plant growth. The study was carried out on Argiudolls and Hapludolls of Santa Fe. Soil samples were collected to determine texture, organic matter content, bulk density, water retention curve, soil resistance to penetration, least limiting water range, critical bulk density for plant growth, compression index, pre-consolidation pressure and soil compressibility. Water retention curve and soil resistance to penetration were linearly and significantly related to clay and organic matter (R2 = 0.91 and R2 = 0.84). The pedotransfer functions of water retention curve and soil resistance to penetration allowed the estimation of the least limiting water range and critical bulk density for plant growth. A significant nonlinear relationship was found between critical bulk density for plant growth and clay content (R2 = 0.98). Compression index was significantly related to bulk density, water content, organic matter and clay plus silt content (R2 = 0.77). Pre-consolidation pressure was significantly related to organic matter, clay and water content (R2 = 0.77). Soil compressibility was significantly related to initial soil bulk density, clay and water content. A nonlinear and significantly pedotransfer function (R2 = 0.88) was developed to predict the maximum acceptable pressure to be applied during tillage operations by introducing critical bulk density for plant growth in the compression model. The developed pedotransfer function provides a useful tool to link the mechanical behavior and tilth of the soils studied. PMID:27099925

Understanding the bias between moisture content by oven drying and water content by Karl Fischer titration at moisture equilibrium

USDA-ARS?s Scientific Manuscript database

Multiple causes of the difference between equilibrium moisture and water content have been found. The errors or biases were traced to the oven drying procedure to determine moisture content. The present paper explains the nature of the biases in oven drying and how it is possible to suppress one ...

Effect of different drying methods on the composition of steviol glycosides in Stevia rebaudiana Bertoni leaves

NASA Astrophysics Data System (ADS)

Aranda-González, Irma; Betancur-Ancona, David; Chel-Guerrero, Luis; Moguel-Ordóñez, Yolanda

2017-01-01

Drying techniques can modify the composition of certain plant compounds. Therefore, the aim of the study was to assess the effect of different drying methods on steviol glycosides in Stevia rebaudiana Bertoni leaves. Four different drying methods were applied to Stevia rebaudiana Bertoni leaves, which were then subjected to aqueous extraction. Radiation or convection drying was performed in stoves at 60°C, whereas shade or sun drying methods were applied at 29.7°C and 70% of relative humidity. Stevioside, rebaudioside A, rebaudioside B, rebaudioside C, rebaudioside D, dulcoside A, and steviolbioside were quantified by a validated HPLC method. Among steviol glycosides, the content (g 100 g-1 dry basis) of stevioside, rebaudioside A, rebaudioside B, and rebaudioside C varied according to the drying method. The total glycoside content was higher in sun-dried samples, with no significant differences compared to shade or convection drying, whereas radiation drying adversely affected the content of rebaudioside A and rebaudioside C (p <0.01) and was therefore a method lowering total glycoside content. The effect of the different drying methods was also reflected in the proportion of the sweetener profile. Convection drying could be suitable for modern food processing industries while shadow or sun drying may be a low-cost alternative for farmers.

Development of a Bulk-Format System to Harvest, Handle, Store, and Deliver High-Tonnage Low-Moisture Switchgrass Feedstock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Womac, Alvin; Groothuis, Mitch; Westover, Tyler

2013-09-24

This project evaluates and compares comprehensive feedstock logistics systems (FLS), where a FLS is defined to comprehensively span from biomass material standing in a field to conveyance of a uniform, industrial-milled product into the throat of a biomass conversion facility (BCF). Elements of the bulk-format FLS evaluated in this project include: field-standing switchgrass dry chopped into bulk format on the farm, hauled (either loose or bulk compacted) to storage, stored with confining overburden in a protective facility, reclaimed and conveyed to bulk-format discharge, bulk compacted into an ejector trailer, and conveyed as bulk flow into the BCF. In this FLSmore » evaluation, bulk storage bins served as a controlled and sensored proxy for large commercial stacks protected from moisture with a membrane cover.« less

Recovery of Waste Heat from Propellant Forced-Air Dry House

DTIC Science & Technology

1978-12-01

function of bulk air side film heat transfer coefficient and diffusivity 66 15. Dry house waste heat recovery system instrumentation 67 16. Sample data...inlet condition by, maintaining the exhaust temperature above the NG dew point. The set point is adjustable to accommodate various propel- lant and...system. In dry cycle operation, an overall energy recovery effectiveness of about 40% was measured for winter operation when the exhaust temperature

46 CFR 98.30-37 - Firefighting requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CONSTRUCTION, ARRANGEMENT, AND OTHER PROVISIONS FOR CERTAIN DANGEROUS CARGOES IN BULK Portable Tanks § 98.30-37... a dry chemical type are— (1) Located to protect the deck area 10 feet in any horizontal direction..., there are 2 or more dry chemical fire extinguishers of 300 pounds or more total capacity of...

Comparison of standard moisture loss-on-drying methods for the determination of moisture content of corn distillers dried grains with solubles.

PubMed

Ileleji, Klein E; Garcia, Arnoldo A; Kingsly, Ambrose R P; Clementson, Clairmont L

2010-01-01

This study quantified the variability among 14 standard moisture loss-on-drying (gravimetric) methods for determination of the moisture content of corn distillers dried grains with solubles (DDGS). The methods were compared with the Karl Fischer (KF) titration method to determine their percent variation from the KF method. Additionally, the thermo-balance method using a halogen moisture analyzer that is routinely used in fuel ethanol plants was included in the methods investigated. Moisture contents by the loss-on-drying methods were significantly different for DDGS samples from three fuel ethanol plants. The percent deviation of the moisture loss-on-drying methods decreased with decrease in drying temperature and, to a lesser extent, drying time. This was attributed to an overestimation of moisture content in DDGS due to the release of volatiles at high temperatures. Our findings indicate that the various methods that have been used for moisture determination by moisture loss-on-drying will not give identical results and therefore, caution should be exercised when selecting a moisture loss-on-drying method for DDGS.

Freeze-Thaw Cycle Test on Basalt, Diorite and Tuff Specimens with the Simulated Ground Temperature of Antarctica

NASA Astrophysics Data System (ADS)

Park, J.; Hyun, C.; Cho, H.; Park, H.

2010-12-01

Physical weathering caused by freeze-thaw action in cold regions was simulated with artificial weathering simulator in laboratory. Physical weathering of rock in cold regions usually depends on the temperature, rock type and moisture content. Then these three variables were considered in this study. The laboratory freeze-thaw tests were conducted on the three types of rocks, e.g. diorite, basalt and tuff, which are the major rock types around Sejong Station, King George Island, Antarctica. Nine core samples composed of three samples from each rock type were prepared in NX core, and 50 cycles of freeze-thaw test was carried out under dried and saturated water conditions. In this study, the physical weathering of rocks was investigated after each 10 cycles by measuring P-wave velocity, bulk density, effective porosity, Schmidt hardness and uniaxial compression strength(UCS). The experimental result of the diorite and the tuff specimens showed that P-wave velocity, bulk density, effective porosity, Schmidt hardness and UCS were gradually decreased as weathering progresses, but the result of the basalt specimens did not show typical trends due to the characteristics of irregular pore distribution and various pore sizes. Scanning electron microscopy(SEM) photographs of diorite, basalt and tuff specimens weathered in dried and saturated conditions were also acquired to investigate the role of water during physical weathering processes. The number and size of microcracks were increased as weathering progresses. This work was supported by the National Research Foundation of Korea(NRF) Grant(NRF-2010-0027753).

The Influence of Basic Physical Properties of Soil on its Electrical Resistivity Value under Loose and Dense Condition

NASA Astrophysics Data System (ADS)

Abidin, M. H. Z.; Ahmad, F.; Wijeyesekera, D. C.; Saad, R.

2014-04-01

Electrical resistivity technique has become a famous alternative tool in subsurface characterization. In the past, several interpretations of electrical resistivity results were unable to be delivered in a strong justification due to lack of appreciation of soil mechanics. Traditionally, interpreters will come out with different conclusion which commonly from qualitative point of view thus creating some uncertainty regarding the result reliability. Most engineers desire to apply any techniques in their project which are able to provide some clear justification with strong, reliable and meaningful results. In order to reduce the problem, this study presents the influence of basic physical properties of soil due to the electrical resistivity value under loose and dense condition. Two different conditions of soil embankment model were tested under electrical resistivity test and basic geotechnical test. It was found that the electrical resistivity value (ERV, ρ) was highly influenced by the variations of soil basic physical properties (BPP) with particular reference to moisture content (w), densities (ρbulk/dry), void ratio (e), porosity (η) and particle grain fraction (d) of soil. Strong relationship between ERV and BPP can be clearly presents such as ρ ∞ 1/w, ρ ∞ 1/ρbulk/dry, ρ ∞ e and ρ ∞ η. This study therefore contributes a means of ERV data interpretation using BPP in order to reduce ambiguity of ERV result and interpretation discussed among related persons such as geophysicist, engineers and geologist who applied these electrical resistivity techniques in subsurface profile assessment.

46 CFR 154.1160 - Monitor coverage of system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Monitor coverage of system. 154.1160 Section 154.1160 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Firefighting System: Dry Chemical § 154.1160...

46 CFR 154.1160 - Monitor coverage of system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Monitor coverage of system. 154.1160 Section 154.1160 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Firefighting System: Dry Chemical § 154.1160...

Bulk densities of materials from selected pine-site hardwoods

Treesearch

Clyde Vidrine; George E. Woodson

1982-01-01

Bulk densities of hardwood materials from low and high density species were determined for green and air-dry conditions. Materials consisted of whole-tree chips, bark-free chips, bark as collected from three types of debarkers (ring, rosser head, and drum debarkers) sawdust, planer shavings, flakes, logging residues, baled branchwood, steel-strapped firewood, and...

Estimates of olivine-basaltic melt electrical conductivity using a digital rock physics approach

NASA Astrophysics Data System (ADS)

Miller, Kevin J.; Montési, Laurent G. J.; Zhu, Wen-lu

2015-12-01

Estimates of melt content beneath fast-spreading mid-ocean ridges inferred from magnetotelluric tomography (MT) vary between 0.01 and 0.10. Much of this variation may stem from a lack of understanding of how the grain-scale melt geometry influences the bulk electrical conductivity of a partially molten rock, especially at low melt fraction. We compute bulk electrical conductivity of olivine-basalt aggregates over 0.02 to 0.20 melt fraction by simulating electric current in experimentally obtained partially molten geometries. Olivine-basalt aggregates were synthesized by hot-pressing San Carlos olivine and high-alumina basalt in a solid-medium piston-cylinder apparatus. Run conditions for experimental charges were 1.5 GPa and 1350 °C. Upon completion, charges were quenched and cored. Samples were imaged using synchrotron X-ray micro-computed tomography (μ-CT). The resulting high-resolution, 3-dimensional (3-D) image of the melt distribution constitutes a digital rock sample, on which numerical simulations were conducted to estimate material properties. To compute bulk electrical conductivity, we simulated a direct current measurement by solving the current continuity equation, assuming electrical conductivities for olivine and melt. An application of Ohm's Law yields the bulk electrical conductivity of the partially molten region. The bulk electrical conductivity values for nominally dry materials follow a power-law relationship σbulk = Cσmeltϕm with fit parameters m = 1.3 ± 0.3 and C = 0.66 ± 0.06. Laminar fluid flow simulations were conducted on the same partially molten geometries to obtain permeability, and the respective pathways for electrical current and fluid flow over the same melt geometry were compared. Our results indicate that the pathways for flow fluid are different from those for electric current. Electrical tortuosity is lower than fluid flow tortuosity. The simulation results are compared to existing experimental data, and the potential influence of volatiles and melt films on electrical conductivity of partially molten rocks is discussed.

Comparison of three different wastewater sludge and their respective drying processes: Solar, thermal and reed beds - Impact on organic matter characteristics.

PubMed

Collard, Marie; Teychené, Benoit; Lemée, Laurent

2017-12-01

Drying process aims at minimising the volume of wastewater sludge (WWS) before disposal, however it can impact sludge characteristics. Due to its high content in organic matter (OM) and lipids, sludge are mainly valorised by land farming but can also be considered as a feedstock for biodiesel production. As sludge composition is a major parameter for the choice of disposal techniques, the objective of this study was to determine the influence of the drying process. To reach this goal, three sludges obtained from solar, reed beds and thermal drying processes were investigated at the global and molecular scales. Before the drying step the sludges presented similar physico-chemical (OM content, elemental analysis, pH, infrared spectra) characteristics and lipid contents. A strong influence of the drying process on lipids and humic-like substances contents was observed through OM fractionation. Thermochemolysis-GCMS of raw sludge and lipids revealed similar molecular content mainly constituted with steroids and fatty acids. Molecular changes were noticeable for thermal drying through differences in branched to linear fatty acids ratio. Finally the thermal drying induced a weakening of OM whereas the solar drying led to a complexification. These findings show that smooth drying processes such as solar or reed-beds are preferable for amendment production whereas thermal process leads to pellets with a high lipid content which could be considered for fuel production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Phenolic compounds and vitamins in wild and cultivated apricot (Prunus armeniaca L.) fruits grown in irrigated and dry farming conditions.

PubMed

Kan, Tuncay; Gundogdu, Muttalip; Ercisli, Sezai; Muradoglu, Ferhad; Celik, Ferit; Gecer, Mustafa Kenan; Kodad, Ossama; Zia-Ul-Haq, Muhammad

2014-09-23

Turkey is the main apricot producer in the world and apricots have been produced under both dry and irrigated conditions in the country. In this study, phenolic compounds and vitamins in fruits of one wild (Zerdali) and three main apricot cultivars ('Cataloglu', 'Hacihaliloglu' and 'Kabaasi') grown in both dry and irrigated conditions in Malatya provinces in Turkey were investigated. The findings indicated that higher content of phenolic compounds and vitamins was found in apricot fruits grown in irrigated conditions. Among the cultivars, 'Cataloglu' had the highest rutin contents both in irrigated and dry farming conditions as 2855 μg in irrigated and 6952 μg per 100 g dried weight base in dry conditions and the highest chlorogenic acid content in irrigated and dry farming conditions were measured in fruits of 'Hacıhaliloglu' cultivar as 7542 μg and 15251 μg per 100 g dried weight base. Vitamin C contents in homogenates of fruit flesh and skin was found to be higher than β-caroten, retinol, vitamin E and lycopen contents in apricot fruits both in irrigated and dry farming conditions. The results suggested that apricot fruits grown in both dry and irrigated conditions had high health benefits phytochemicals and phytochemical content varied among cultivars and irrigation conditions as well. However, more detailed biological and pharmacological studies are needed for the demonstration and clarification of health benefits of apricot fruits.

Somatic cell counts in bulk milk and their importance for milk processing

NASA Astrophysics Data System (ADS)

Savić, N. R.; Mikulec, D. P.; Radovanović, R. S.

2017-09-01

Bulk tank milk somatic cell counts are the indicator of the mammary gland health in the dairy herds and may be regarded as an indirect measure of milk quality. Elevated somatic cell counts are correlated with changes in milk composition The aim of this study was to assess the somatic cell counts that significantly affect the quality of milk and dairy products. We examined the somatic cell counts in bulk tank milk samples from 38 farms during the period of 6 months, from December to the May of the next year. The flow cytometry, Fossomatic was used for determination of somatic cell counts. In the same samples content of total proteins and lactose was determined by Milcoscan. Our results showed that average values for bulk tank milk samples were 273,605/ml from morning milking and 292,895/ml from evening milking. The average values for total proteins content from morning and evening milking are 3,31 and 3,34%, respectively. The average values for lactose content from morning and evening milking are 4,56 and 4,63%, respectively. The highest somatic cell count (516,000/ml) was detected in bulk tank milk sample from evening milk in the Winter and the lowest content of lactose was 4,46%. Our results showed that obtained values for bulk tank milk somatic cell counts did not significantly affected the content of total proteins and lactose.

A field survey on coffee beans drying methods of Indonesian small holder farmers

NASA Astrophysics Data System (ADS)

Siagian, Parulian; Setyawan, Eko Y.; Gultom, Tumiur; Napitupulu, Farel H.; Ambarita, Himsar

2017-09-01

Drying agricultural product is a post-harvest process that consumes significant energy. It can affect the quality of the product. This paper deals with literature review and field survey of drying methods of coffee beans of Indonesia farmers. The objective is to supply the necessary information on developing continuous solar drier. The results show that intermittent characteristic of sun drying results in a better quality of coffee beans in comparison with constant convective drying. In order to use energy efficiently, the drying process should be divided into several stages. In the first stage when the moist content is high, higher drying air temperature is more effective. After this step, where the moist content is low, lower drying air temperature is better. The field survey of drying coffee beans in Sumatera Utara province reveals that the used drying process is very traditional. It can be divided into two modes and depend on the coffee beans type. The Arabica coffee is firstly fermented and dried to moisture content of 80% using sun drying method, then followed by Green House model of drying up to moisture content about 12%. The latter typically spends 3 days of drying time. On the other hand, The Robusta coffee is dried by exposing to the sun directly without any treatment. After the coffee beans dried follow by peeled process. These findings can be considered to develop a continuous solar drying that suitable for coffee beans drying.

Influence of formulation excipients and physical characteristics of inhalation dry powders on their aerosolization performance.

PubMed

Bosquillon, C; Lombry, C; Préat, V; Vanbever, R

2001-02-23

The objective of this study was to determine the effects of formulation excipients and physical characteristics of inhalation particles on their in vitro aerosolization performance, and thereby to maximize their respirable fraction. Dry powders were produced by spray-drying using excipients that are FDA-approved for inhalation as lactose, materials that are endogenous to the lungs as albumin and dipalmitoylphosphatidylcholine (DPPC); and/or protein stabilizers as trehalose or mannitol. Dry powders suitable for deep lung deposition, i.e. with an aerodynamic diameter of individual particles <3 microm, were prepared. They presented 0.04--0.25 g/cm(3) bulk tap densities, 3--5 microm geometric particle sizes, up to 90% emitted doses and 50% respirable fractions in the Andersen cascade impactor using a Spinhaler inhaler device. The incorporation of lactose, albumin and DPPC in the formulation all improved the aerosolization properties, in contrast to trehalose and the mannitol which decreased powder flowability. The relative proportion of the excipients affected aerosol performance as well. The lower the bulk powder tap density, the higher the respirable fraction. Optimization of in vitro aerosolization properties of inhalation dry powders can be achieved by appropriately selecting composition and physical characteristics of the particles.

Evaluation of a microwave method for dry matter determination in faecal samples from weaned pigs with or without clinical diarrhoea.

PubMed

Pedersen, Ken Steen; Stege, Helle; Nielsen, Jens Peter

2011-07-01

Microwave drying as a procedure for determination of faecal dry matter in weaned pigs was evaluated and clinical relevant cut-off values between faecal consistency scores were determined. Repeatability and reproducibility were evaluated. Overall coefficient of variation was 0.03. The 95% confidence limits for any future faecal subsample examined by any operator in any replica were ± 0.85% faecal dry matter. Robustness in relation to weight of wet faeces was evaluated. The weight categories were 0.5, 1.0, 1.5, 2.0 and 3.0 g. Samples of 0.5 g gave significantly different mean faecal dry matter content compared to weighing of 1.0-3.0 g. Agreement with freeze-drying was evaluated. Lin's concordance correlation coefficient was 0.94. On average the faecal dry matter values was 1.7% (SD=1.99%) higher in freeze dried compared to micro waved samples. Non-parametric ROC analyses were used to determine optimal faecal dry matter cut-off values for clinical faecal consistency scores. The 4 consistency scores were score 1=firm and shaped, score 2=soft and shaped, score 3=loose and score 4=watery. The cut-off values were score 1: faecal dry matter content >19.5%, score 2: faecal dry matter content ≤ 19.5% and >18.0%, score 3: faecal dry matter content ≤ 18.0% and >11.3%, score 4: faecal dry matter content ≤ 11.3%. In conclusion, the microwave procedure has an acceptable repeatability/reproducibility and good agreement with freeze drying can be expected. A minimum of 1.0 g of wet faeces must be used for analyses. Faecal dry matter cut-off values between 4 different clinical consistency scores were determined. © 2011 Elsevier B.V. All rights reserved.

Bulk Genotyping of Biopsies Can Create Spurious Evidence for Hetereogeneity in Mutation Content.

PubMed

Kostadinov, Rumen; Maley, Carlo C; Kuhner, Mary K

2016-04-01

When multiple samples are taken from the neoplastic tissues of a single patient, it is natural to compare their mutation content. This is often done by bulk genotyping of whole biopsies, but the chance that a mutation will be detected in bulk genotyping depends on its local frequency in the sample. When the underlying mutation count per cell is equal, homogenous biopsies will have more high-frequency mutations, and thus more detectable mutations, than heterogeneous ones. Using simulations, we show that bulk genotyping of data simulated under a neutral model of somatic evolution generates strong spurious evidence for non-neutrality, because the pattern of tissue growth systematically generates differences in biopsy heterogeneity. Any experiment which compares mutation content across bulk-genotyped biopsies may therefore suggest mutation rate or selection intensity variation even when these forces are absent. We discuss computational and experimental approaches for resolving this problem.

A Database and Synthesis of Northern Peatland Soil Properties and Holocene Carbon and Nitrogen Accumulation

NASA Technical Reports Server (NTRS)

Loisel, Julie; Yu, Zicheng; Beilman, David W.; Camill, Philip; Alm, Jukka; Amesbury, Matthew J.; Anderson, David; Andersson, Sofia; Bochicchio, Christopher; Barber, Keith;

Conocarpus biochar as a soil amendment for reducing heavy metal availability and uptake by maize plants.

PubMed

Al-Wabel, Mohammad I; Usman, Adel R A; El-Naggar, Ahmed H; Aly, Anwar A; Ibrahim, Hesham M; Elmaghraby, Salem; Al-Omran, Abdulrasoul

2015-07-01

The objective of this study was to assess the use of Concarpus biochar as a soil amendment for reducing heavy metal accessibility and uptake by maize plants (Zea mays L.). The impacts of biochar rates (0.0, 1.0, 3.0, and 5.0% w/w) and two soil moisture levels (75% and 100% of field capacity, FC) on immobilization and availability of Fe, Mn, Zn, Cd, Cu and Pb to maize plants as well as its application effects on soil pH, EC, bulk density, and moisture content were evaluated using heavy metal-contaminated soil collected from mining area. The biochar addition significantly decreased the bulk density and increased moisture content of soil. Applying biochar significantly reduced NH4OAc- or AB-DTPA-extractable heavy metal concentrations of soils, indicating metal immobilization. Conocarpus biochar increased shoot dry biomass of maize plants by 54.5-102% at 75% FC and 133-266% at 100% FC. Moreover, applying biochar significantly reduced shoot heavy metal concentrations in maize plants (except for Fe at 75% FC) in response to increasing application rates, with a highest decrease of 51.3% and 60.5% for Mn, 28% and 21.2% for Zn, 60% and 29.5% for Cu, 53.2% and 47.2% for Cd at soil moisture levels of 75% FC and 100% FC, respectively. The results suggest that biochar may be effectively used as a soil amendment for heavy metal immobilization and in reducing its phytotoxicity.

Conocarpus biochar as a soil amendment for reducing heavy metal availability and uptake by maize plants

PubMed Central

Al-Wabel, Mohammad I.; Usman, Adel R.A.; El-Naggar, Ahmed H.; Aly, Anwar A.; Ibrahim, Hesham M.; Elmaghraby, Salem; Al-Omran, Abdulrasoul

2014-01-01

The objective of this study was to assess the use of Concarpus biochar as a soil amendment for reducing heavy metal accessibility and uptake by maize plants (Zea mays L.). The impacts of biochar rates (0.0, 1.0, 3.0, and 5.0% w/w) and two soil moisture levels (75% and 100% of field capacity, FC) on immobilization and availability of Fe, Mn, Zn, Cd, Cu and Pb to maize plants as well as its application effects on soil pH, EC, bulk density, and moisture content were evaluated using heavy metal-contaminated soil collected from mining area. The biochar addition significantly decreased the bulk density and increased moisture content of soil. Applying biochar significantly reduced NH4OAc- or AB-DTPA-extractable heavy metal concentrations of soils, indicating metal immobilization. Conocarpus biochar increased shoot dry biomass of maize plants by 54.5–102% at 75% FC and 133–266% at 100% FC. Moreover, applying biochar significantly reduced shoot heavy metal concentrations in maize plants (except for Fe at 75% FC) in response to increasing application rates, with a highest decrease of 51.3% and 60.5% for Mn, 28% and 21.2% for Zn, 60% and 29.5% for Cu, 53.2% and 47.2% for Cd at soil moisture levels of 75% FC and 100% FC, respectively. The results suggest that biochar may be effectively used as a soil amendment for heavy metal immobilization and in reducing its phytotoxicity. PMID:26150758

Changes of hydrogen peroxide and radical-scavenging activity of raspberry during osmotic, convective, and freeze-drying.

PubMed

Novaković, Miroslav M; Stevanović, Snežana M; Gorjanović, Stanislava Ž; Jovanovic, Predrag M; Tešević, Vele V; Janković, Miodrag A; Sužnjević, Desanka Ž

2011-05-01

This study was conducted to investigate the influence of different drying treatments on antioxidant (AO) activity and phenolic content of raspberry (Rubus idaeus), cultivar Willamette. Whole raspberry fruits were dried convectively (air-drying), osmotically, and freeze-dried. Acetone-water extracts of fresh and dried raspberries were assessed for total phenolic content by standard Folin-Ciocalteau method. Two AO assays were applied, a recently developed direct current (DC) polarographic assay based on decrease of anodic oxidation current of hydrogen peroxide and widely used radical scavenge against the 1,1-diphenyl-2-picrylhydrazyl (DPPH). Strong correlation has been obtained between both AO assays and total phenolic content. In addition, some individual phenolic compounds present in raspberry have been assessed using DPPH and DC polarographic assay. Comparison and evaluation of drying methods has been based on preservation of AO activity and total phenolic content. Obtained results confirmed superiority of freeze-drying; convective drying caused slight changes while osmotic dehydration showed a significant decrease of phenolic compounds and AO activity. © 2011 Institute of Food Technologists®

Microwave-Assisted Drying for the Conservation of Honeybee Pollen.

PubMed

Canale, Angelo; Benelli, Giovanni; Castagna, Antonella; Sgherri, Cristina; Poli, Piera; Serra, Andrea; Mele, Marcello; Ranieri, Annamaria; Signorini, Francesca; Bientinesi, Matteo; Nicolella, Cristiano

2016-05-12

Bee pollen is becoming an important product thanks to its nutritional properties, including a high content of bioactive compounds such as essential amino acids, antioxidants, and vitamins. Fresh bee pollen has a high water content (15%-30% wt %), thus it is a good substrate for microorganisms. Traditional conservation methods include drying in a hot air chamber and/or freezing. These techniques may significantly affect the pollen organoleptic properties and its content of bioactive compounds. Here, a new conservation method, microwave drying, is introduced and investigated. The method implies irradiating the fresh pollen with microwaves under vacuum, in order to reduce the water content without reaching temperatures capable of thermally deteriorating important bioactive compounds. The method was evaluated by taking into account the nutritional properties after the treatment. The analyzed parameters were phenols, flavonoids, with special reference to rutin content, and amino acids. Results showed that microwave drying offers important advantages for the conservation of bee pollen. Irrespective of microwave power and treatment time, phenol and flavonoid content did not vary over untreated fresh pollen. Similarly, rutin content was unaffected by the microwave drying, suggesting that the microwave-assisted drying could be a powerful technology to preserve bioprotective compounds in fresh pollen.

[Purine in common plant food in China].

PubMed

Rong, Shengzhong; Zou, Lina; Wang, Zhaoxu; Pan, Hongzhi; Yang, Yuexin

2012-01-01

To determine the content of purine in plant food in China with HPLC. HPLC analysis was applied on Waters Atlantis T3 column (4.6mm x 250mm x 5 microm), using 10.0 mmol/L NH4COOH (pH 3.6) and CH3OH (99%/1%) as mobile phase and running at a flow rate of 1.0 ml/min. The column temperature was 30 degrees C, and the detection wavelength was at 254nm. The content of purine varied significantly in different kinds of plant food. The content of purine in dried fungi and dried legumes and legume products was higher than that in other food, the content of purine in vegetables and vegetable products and fruits and fruit products was low. As a whole, the content of purine was: dried fungi and algae > dried legumes and legume products > nuts and fresh > seeds fungi and algae > cereal and cereals products > vegetables and vegetable products > fruit and fruit products > tubers, starches and products. The content of purine of dried fungi and algae and dried legumes and legume products in plant food was high. The content of purine was varied significantly in different kinds of plant food.

Sustained release of diltiazem HCl tableted after co-spray drying and physical mixing with PVAc and PVP.

PubMed

Al-Zoubi, Nizar; Al-Obaidi, Ghada; Tashtoush, Bassam; Malamataris, Stavros

2016-01-01

In this work, aqueous diltiazem HCl and polyvinyl-pyrrolidone (PVP) solutions were mixed with Kollicoat SR 30D and spray dried to microparticles of different drug:excipient ratio and PVP content. Co-spray dried products and physical mixtures of drug, Kollidon SR and PVP were tableted. Spray drying process, co-spray dried products and compressibility/compactability of co-spray dried and physical mixtures, as well as drug release and water uptake of matrix-tablets was evaluated. Simple power equation fitted drug release and water uptake (R(2) > 0.909 and 0.938, respectively) and correlations between them were examined. Co-spray dried products with PVP content lower than in physical mixtures result in slower release, while at equal PVP content (19 and 29% w/w of excipient) in similar release (f2 > 50). Increase of PVP content increases release rate and co-spray drying might be an alternative, when physical mixing is inadequate. Co-spray dried products show better compressibility/compatibility but higher stickiness to the die-wall compared to physical mixtures. SEM observations and comparison of release and swelling showed that distribution of tableted component affects only the swelling, while PVP content for both co-spray dried and physical mixes is major reason for release alterations and an aid for drug release control.

Water regime influences bulk soil and Rhizosphere of Cereus jamacaru bacterial communities in the Brazilian Caatinga biome.

PubMed

Nessner Kavamura, Vanessa; Taketani, Rodrigo Gouvêa; Lançoni, Milena Duarte; Andreote, Fernando Dini; Mendes, Rodrigo; Soares de Melo, Itamar

2013-01-01

We used the T-RFLP technique combined with Ion Torrent (PGM) sequencing of 16S rRNA and multivariate analysis to study the structure of bulk soil and rhizosphere bacterial communities of a cactus, Cereus jamacaru, from the Brazilian Caatinga biome, which is unique to Brazil. The availability of water shapes the rhizosphere communities, resulting in different patterns during the rainy and dry seasons. Taxonomic approaches and statistical analysis revealed that the phylum Actinobacteria strongly correlated with the dry season, while samples from the rainy season exhibited a strong correlation with the phylum Proteobacteria for rhizosphere samples and with the phyla Bacteroidetes, Firmicutes, Lentisphaerae, and Tenericutes for bulk soil samples. The STAMP software also indicated that the phylum Bacteroidetes, as well as two classes in the Proteobacteria phylum (γ and δ), were the most significant ones during the rainy season. The average abundance of the phylum Actinobacteria and the genus Bacillus was significantly greater during the dry season. Some significant genera found during the dry season might reflect their tolerance to the extreme conditions found in the Caatinga biome. They may also indicate the ecological function that microorganisms play in providing plants with some degree of tolerance to water stress or in assisting in their development through mechanisms of growth promotion. Alterations in microbial communities can be due to the different abilities of native microorganisms to resist and adapt to environmental changes.

Water Regime Influences Bulk Soil and Rhizosphere of Cereus jamacaru Bacterial Communities in the Brazilian Caatinga Biome

PubMed Central

Nessner Kavamura, Vanessa; Taketani, Rodrigo Gouvêa; Lançoni, Milena Duarte; Andreote, Fernando Dini; Mendes, Rodrigo; Soares de Melo, Itamar

2013-01-01

We used the T-RFLP technique combined with Ion Torrent (PGM) sequencing of 16S rRNA and multivariate analysis to study the structure of bulk soil and rhizosphere bacterial communities of a cactus, Cereus jamacaru, from the Brazilian Caatinga biome, which is unique to Brazil. The availability of water shapes the rhizosphere communities, resulting in different patterns during the rainy and dry seasons. Taxonomic approaches and statistical analysis revealed that the phylum Actinobacteria strongly correlated with the dry season, while samples from the rainy season exhibited a strong correlation with the phylum Proteobacteria for rhizosphere samples and with the phyla Bacteroidetes, Firmicutes, Lentisphaerae, and Tenericutes for bulk soil samples. The STAMP software also indicated that the phylum Bacteroidetes, as well as two classes in the Proteobacteria phylum (γ and δ), were the most significant ones during the rainy season. The average abundance of the phylum Actinobacteria and the genus Bacillus was significantly greater during the dry season. Some significant genera found during the dry season might reflect their tolerance to the extreme conditions found in the Caatinga biome. They may also indicate the ecological function that microorganisms play in providing plants with some degree of tolerance to water stress or in assisting in their development through mechanisms of growth promotion. Alterations in microbial communities can be due to the different abilities of native microorganisms to resist and adapt to environmental changes. PMID:24069212

Heated fiber optic distributed temperature sensing: a tool for measuring soil water content

NASA Astrophysics Data System (ADS)

Rodriguez-Sinobas, Leonor; Zubelzu, Sergio; Sánchez-Calvo, Raúl; Horcajo, Daniel

2016-04-01

The use of Distributed Fiber Optic Temperature Measurement (DFOT) method for estimating temperature variation along a cable of fiber optic has been assessed in multiple environmental applications. Recently, the application of DFOT combined with an active heating pulses technique has been reported as a sensor to estimate soil moisture. This method applies a known amount of heat to the soil and monitors the temperature evolution, which mainly depends on the soil moisture content . This study presents the application of the Active Heated DFOT method to determine the soil water retention curve under experimental conditions. The experiment was conducted in a rectangular methacrylate box of 2.5 m x 0.25 m x 0.25 m which was introduced in a larger box 2.8 m x 0.3 m x 0.3 m of the same material. The inner box was filled with a sandy loamy soil collected from the nearest garden and dried under ambient temperature for 30 days. Care was taking to fill up the box maintaining the soil bulk density determined "in-situ". The cable was deployed along the box at 10 cm depth. At the beginning of the experiment, the box was saturated bottom-up, by filling the outer box with water, and then it kept dried for two months. The circulation of heated air at the bottom box accelerated the drying process. In addition, fast growing turf was also sowed to dry it fast. The DTS unit was a SILIXA ULTIMA SR (Silixa Ltd, UK) and has spatial and temporal resolution of 0.29 m and 5 s, respectively. In this study, heat pulses of 7 W/m for 2 1/2 min were applied uniformly along the fiber optic cable and the thermal response on an adjacent cable was monitored in different soil water status. Then, the heating and drying phase integer (called Tcum) was determined following the approach of Sayde et al., (2010). For each water status,  was measured by the gravimetric method in several soil samples collected in three box locations at the same depth that the fiber optic cable and after each heat pulse. Finally, the soil water retention curve was estimated by fitting pairs of Tcum- values. Results showed the feasibility of heated fiber optics with distributed temperature sensing to estimate soil water content, and suggest its potential for its application under field conditions

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Code of Federal Regulations, 2013 CFR

2013-07-01

.... 1005.00 Corn (Maize). 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek. 0713.32 Small red (adzuki) beans. 0713.33 Kidney beans, including white pea beans. 0713.39 Beans, other. 0713.50 Broad beans and horse beans. 0713.10 Dried Peas (Pisum sativum). 0713.20 Chickpeas...

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Code of Federal Regulations, 2014 CFR

2014-07-01

...) 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils...

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Code of Federal Regulations, 2012 CFR

2012-07-01

... (Maize) 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40...

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Code of Federal Regulations, 2011 CFR

2011-07-01

... Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils 0713.90 Dried...

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Code of Federal Regulations, 2013 CFR

2013-07-01

...) 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils...

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Code of Federal Regulations, 2012 CFR

2012-07-01

...) 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils...

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Code of Federal Regulations, 2014 CFR

2014-07-01

.... 1005.00 Corn (Maize). 0713.31 Dried Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek. 0713.32 Small red (adzuki) beans. 0713.33 Kidney beans, including white pea beans. 0713.39 Beans, other. 0713.50 Broad beans and horse beans. 0713.10 Dried Peas (Pisum sativum). 0713.20 Chickpeas...

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Code of Federal Regulations, 2011 CFR

2011-07-01

... Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils 0713.90 Dried...

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Code of Federal Regulations, 2010 CFR

2010-07-01

... Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils 0713.90 Dried...

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Code of Federal Regulations, 2010 CFR

2010-07-01

... Beans including Vigna mungo (L.), Hepper, and Vigna radiata (L.) Wilczek 0713.32 Small red (adzuki) beans 0713.33 Kidney beans, including white pea beans 0713.39 Beans, other 0713.50 Broad beans and horse beans 0713.10 Dried Peas (Pisum sativum) 0713.20 Chickpeas (garbanzos) 0713.40 Lentils 0713.90 Dried...

Optimization and modeling of flow characteristics of low-oil DDGS using regression techniques

USDA-ARS?s Scientific Manuscript database

Storage conditions such as temperature, relative humidity (RH), consolidation pressure (CP), and time affect flow behavior of bulk solids like distillers dried grains with solubles (DDGS), which is widely used as animal feed by the U.S. cattle and swine industries. The typical dry grind DDGS product...

46 CFR 381.7 - Federal Grant, Guaranty, Loan and Advance of Funds Agreements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... each affected department or agency shall require appropriate clauses to be inserted in those Grant... ship at least 50 percent of the gross tonnage (computed separately for dry bulk carriers, dry cargo.... “(3) To insert the substance of the provisions of this clause in all subcontracts issued pursuant to...

Attrition resistant bulk iron catalysts and processes for preparing and using same

DOEpatents

Jothimurugesan, Kandaswamy [Ponca City, OK; Goodwin, Jr., James G.; Gangwal, Santosh K [Cary, NC

2007-08-21

An attrition resistant precipitated bulk iron catalyst is prepared from iron oxide precursor and a binder by spray drying. The catalysts are preferably used in carbon monoxide hydrogenation processes such as Fischer-Tropsch synthesis. These catalysts are suitable for use in fluidized-bed reactors, transport reactors and, especially, slurry bubble column reactors.

40 CFR 761.295 - Reporting and recordkeeping of the PCB concentrations in samples.

Code of Federal Regulations, 2013 CFR

2013-07-01

... concentrations in samples. 761.295 Section 761.295 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... On-Site Disposal of Bulk PCB Remediation Waste and Porous Surfaces in Accordance With § 761.61(a)(6... concentrations for bulk PCB remediation waste and porous surfaces on a dry weight basis and as micrograms of PCBs...

40 CFR 761.295 - Reporting and recordkeeping of the PCB concentrations in samples.

Code of Federal Regulations, 2014 CFR

2014-07-01

... concentrations in samples. 761.295 Section 761.295 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... On-Site Disposal of Bulk PCB Remediation Waste and Porous Surfaces in Accordance With § 761.61(a)(6... concentrations for bulk PCB remediation waste and porous surfaces on a dry weight basis and as micrograms of PCBs...

40 CFR 761.295 - Reporting and recordkeeping of the PCB concentrations in samples.

Code of Federal Regulations, 2011 CFR

2011-07-01

... concentrations in samples. 761.295 Section 761.295 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... On-Site Disposal of Bulk PCB Remediation Waste and Porous Surfaces in Accordance With § 761.61(a)(6... concentrations for bulk PCB remediation waste and porous surfaces on a dry weight basis and as micrograms of PCBs...

40 CFR 761.295 - Reporting and recordkeeping of the PCB concentrations in samples.

Code of Federal Regulations, 2012 CFR

2012-07-01

... concentrations in samples. 761.295 Section 761.295 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... On-Site Disposal of Bulk PCB Remediation Waste and Porous Surfaces in Accordance With § 761.61(a)(6... concentrations for bulk PCB remediation waste and porous surfaces on a dry weight basis and as micrograms of PCBs...

In vitro and in vivo assessment of the effect of initial moisture content and drying temperature on the feeding value of maize grain.

PubMed

Huart, F; Malumba, P; Odjo, S; Al-Izzi, W; Béra, F; Beckers, Y

2018-06-11

1. This study assessed the impact of drying temperature (54, 90, and 130°C) and maize grain moisture content at harvest (36% and 29%) on in vitro digestibility, the growth performance and ileal digestibility of broiler chickens. 2. In contrast to the results from the in vitro digestibility, apparent ileal digestibility of starch and energy decreased when the drying temperature was raised from 54 to 130°C, and this effect was more pronounced in maize grain harvested at high initial moisture content (36%). Ileal protein digestibility of maize grain decreased significantly when dried at the intermediate temperature (90°C) and with a high harvest moisture content (36%). Drying temperature and initial moisture content did not significantly affect AMEn. 3. When maize was dried at 130°C, the particle sizes of flour recovered after standard milling procedures decreased significantly, which would influence animal growth performance and in vivo digestibility through animal feed selection.

Bio-drying of municipal solid waste with high water content by aeration procedures regulation and inoculation.

PubMed

Zhang, Dong-Qing; He, Pin-Jing; Jin, Tai-Feng; Shao, Li-Ming

2008-12-01

To improve the water content reduction of municipal solid waste with high water content, the operations of supplementing a hydrolytic stage prior to aerobic degradation and inoculating the bio-drying products were conducted. A 'bio-drying index' was used to evaluate the bio-drying performance. For the aerobic processes, the inoculation accelerated organics degradation, enhanced the lignocelluloses degradation rate by 10.4%, and lowered water content by 7.0%. For the combined hydrolytic-aerobic processes, the inoculum addition had almost no positive effect on the bio-drying efficiency, but it enhanced the lignocelluloses degradation rate by 9.6% and strengthened the acidogenesis in the hydrolytic stage. Compared with the aerobic processes, the combined processes had a higher bio-drying index (4.20 for non-inoculated and 3.67 for the inoculated trials). Moreover, the lowest final water content occurred in the combined process without inoculation (50.5% decreased from an initial 72.0%).

More on the dynamics of dust generation: the effects of mixing and sanding chrysotile, calcium carbonate, and other components on the characteristics of joint-compound dusts.

PubMed

Berman, D Wayne; Brorby, Gregory P; Sheehan, Patrick J; Bogen, Kenneth T; Holm, Stewart E

2012-08-01

An ongoing research effort designed to reconstruct the character of historical exposures associated with use of chrysotile-containing joint compounds naturally raised questions concerning how the character (e.g. particle size distributions) of dusts generated from use of recreated materials compares to dusts from similar materials manufactured historically. This also provided an opportunity to further explore the relative degree that the characteristics of dusts generated from a bulk material are mediated by the properties of the bulk material versus the mechanical processes applied to the bulk material by which the dust is generated. In the current study, the characteristics of dusts generated from a recreated ready mix and recreated dry mix were compared to each other, to dusts from a historical dry mix, and to dusts from the commercial chrysotile fiber (JM 7RF3) used in the recreated materials. The effect of sanding on the character of dusts generated from these materials was also explored. Dusts from the dry materials studied were generated and captured for analysis in a dust generator-elutriator. The recreated and historical joint compounds were also prepared, applied to drywall, and sanded inside sealed bags so that the particles produced from sanding could be introduced into the elutriator and captured for analysis. Comparisons of fiber size distributions in dusts from these materials suggest that dust from commercial fiber is different from dusts generated from the joint compounds, which are mixtures, and the differences persist whether the materials are sanded or not. Differences were also observed between sanded recreated ready mix and either the recreated dry mix or a historical dry mix, again whether sanded or not. In all cases, however, such differences disappeared when variances obtained from surrogate data were used to better represent the 'irreducible variation' of these materials. Even using the smaller study-specific variances, no differences were observed between the recreated dry mix and the historical dry mix, indicating that chrysotile-containing joint compounds can be recreated using historical formulations such that the characteristics of the modern material reasonably mimic those of a corresponding historical material. Similarly, no significant differences were observed between dusts from sanded and unsanded versions of similar materials, suggesting (as in previous studies) that the characteristics of asbestos-containing dusts are mediated primarily by the properties of the bulk material from which they are derived.

Application of Empirical Peleg Model to Study the Water Adsorption of Full Cream Milk in Drying Process

NASA Astrophysics Data System (ADS)

Hashib, S. Abd; Rosli, H.; Suzihaque, M. U. H.; Zaki, N. A. Md; Ibrahim, U. K.

2017-06-01

The ability of spray dryer in producing full cream milk at different inlet temperatures and the effectiveness of empirical model used in order to interpret the drying process data is evaluated in this study. In this study, a lab-scale spray dryer was used to dry full cream milk into powder with inlet temperature from 100 to 160°C with a constant pump speed 4rpm. Peleg empirical model was chosen in order to manipulate the drying data into the mathematical equation. This research was carry out specifically to determine the equilibrium moisture content of full cream milk powder at various inlet temperature and to evaluate the effectiveness of Peleg empirical model equation in order to describe the moisture sorption curves for full cream milk. There were two conditions set for this experiments; in the first condition (C1), further drying process of milk powder in the oven at 98°C to 100°C while the second condition (C2) is mixing the milk powder with different salt solutions like Magnesium Chloride (MgCl), Potassium Nitrite (KNO2), Sodium Nitrite (NaNO2) and Ammonium Sulfate ((NH4)2SO4). For C1, the optimum temperature were 160°C with equilibrium moisture content at 3.16 weight dry basis and slowest sorption rates (dM/dt) at 0.0743 weight dry basis/hr. For C2, the best temperature for the mixture of dry samples with MgCl is at 115°C with equilibrium moisture content and sorption rates is -78.079 weight dry basis and 0.01 weight dry basis/hr. The best temperature for the mixture of milk powder with KNO2 is also at 115°C with equilibrium moisture content and sorption rates at -83.9645 weight dry basis and 0.0008 weight dry basis/hr respectively. For mixture of dry samples with NaNO2, the best temperature is 160°C with equilibrium moisture content and sorption rates at 84.1306 weight dry basis and 0.0013 weight dry basis/hr respectively. Lastly, the mixture of dry samples with ((NH4)2SO4 where the best temperature is at 115°C with equilibrium moisture content -83.8778 weight dry basis and sorption rates at 0.0021 weight dry basis/hr. The best temperature selected best on the lowest moisture content formed and also the slowest sorption rates.

The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

NASA Astrophysics Data System (ADS)

Saputra, Asep Handaya; Putri, Rizky Anggreini

2017-05-01

Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

Soil water sensor response to bulk electrical conductivity

USDA-ARS?s Scientific Manuscript database

Soil water monitoring using electromagnetic (EM) sensors can facilitate observations of water content at high temporal and spatial resolutions. These sensors measure soil dielectric permittivity (Ka) which is largely a function of volumetric water content. However, bulk electrical conductivity BEC c...

Drying kinetic of industrial cassava flour: Experimental data in view.

PubMed

Odetunmibi, Oluwole A; Adejumo, Oluyemisi A; Oguntunde, Pelumi E; Okagbue, Hilary I; Adejumo, Adebowale O; Suleiman, Esivue A

2017-12-01

In this data article, laboratory experimental investigation results on drying kinetic properties: the drying temperature ( T ), drying air velocity ( V ) and dewatering time (Te), each of the factors has five levels, and the experiment was replicated three times and the output: drying rate and drying time obtained, were observed. The experiment was conducted at National Centre for Agricultural Mechanization (NCAM) for a period of eight months, in 2014. Analysis of variance was carried out using randomized complete block design with factorial experiment on each of the outputs: drying rate and drying times of the industrial cassava flour. A clear picture on each of these outputs was provided separately using tables and figures. It was observed that all the main factors as well as two and three ways interactions are significant at 5% level for both drying time and rate. This also implies that the rate of drying grated unfermented cassava mash, to produce industrial cassava flour, depend on the dewatering time (the initial moisture content), temperature of drying, velocity of drying air as well as the combinations of these factors altogether. It was also discovered that all the levels of each of these factors are significantly difference from one another. In summary, the time of drying is a function of the dewatering time which was responsible for the initial moisture content. The higher the initial moisture content the longer the time of drying, and the lower the initial moisture content, the lower the time of drying. Also, the higher the temperature of drying the shorter the time of drying and vice versa. Also, the air velocity effect on the drying process was significant. As velocity increases, rate of drying also increases and vice versa. Finally, it can be deduced that the drying kinetics are influenced by these processing factors.

27 CFR 24.202 - Dried fruit.

Code of Federal Regulations, 2013 CFR

2013-04-01

... the fresh fruit may be added. If it is desired not to restore the moisture content of the dried fruit to that of the fresh fruit, or if the moisture content is not known, sufficient water may be added to... deficient in sugar, sufficient pure dry sugar may be added to increase the total solids content to 25...

27 CFR 24.202 - Dried fruit.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the fresh fruit may be added. If it is desired not to restore the moisture content of the dried fruit to that of the fresh fruit, or if the moisture content is not known, sufficient water may be added to... deficient in sugar, sufficient pure dry sugar may be added to increase the total solids content to 25...

27 CFR 24.202 - Dried fruit.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the fresh fruit may be added. If it is desired not to restore the moisture content of the dried fruit to that of the fresh fruit, or if the moisture content is not known, sufficient water may be added to... deficient in sugar, sufficient pure dry sugar may be added to increase the total solids content to 25...

27 CFR 24.202 - Dried fruit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the fresh fruit may be added. If it is desired not to restore the moisture content of the dried fruit to that of the fresh fruit, or if the moisture content is not known, sufficient water may be added to... deficient in sugar, sufficient pure dry sugar may be added to increase the total solids content to 25...

Brick Paving Systems in Expeditionary Environments: Field Testing

DTIC Science & Technology

2012-07-01

specific gravity of 2.7, optimum moisture content of 2.6 percent, and a maximum dry density of 114.2 pcf. Figure 5 shows the Proctor curve developed by...4  Figure 3. Dry density versus moisture content for CH material...6  Figure 5. Dry density versus moisture content for blended GM base course. ..................................... 7  Figure 6

Characterization of Inorganic Filler Content, Mechanical Properties, and Light Transmission of Bulk-fill Resin Composites.

PubMed

Fronza, B M; Ayres, Apa; Pacheco, R R; Rueggeberg, F A; Dias, Cts; Giannini, M

The aims of this study were to characterize inorganic content (IC), light transmission (LT), biaxial flexural strength (BFS), and flexural modulus (FM) of one conventional (layered) and four bulk-fill composites at different depths. Bulk-fill composites tested were Surefil SDR flow (SDR), Filtek Bulk Fill (FBF), Tetric EvoCeram Bulk Fill (TEC), and EverX Posterior (EXP). Herculite Classic (HER) was used as a control. Energy dispersive x-ray analysis and scanning electron microscopy were used to characterize filler particle composition and morphology. The LT through different composite thicknesses (1, 2, 3, and 4 mm) was measured using a laboratory-grade spectral radiometer system (n=5). For the BFS and FM tests, sets of eight stacked composite discs (0.5-mm thick) were prepared simulating bulk filling of a 4-mm-thick increment (n=8). SDR demonstrated larger, irregular particles than those observed in TEC or HER. Filler particles in FBF were spherical, while those in EXP were composed of fiberglass strands. The LT decreased with increased composite thickness for all materials. Bulk-fill composites allowed higher LT than the HER. Furthermore, HER proved to be the unique material, having lower BFS values at deeper regions. SDR, FBF, and TEC bulk-fill composites presented reduced FM with increasing composite depth. The bulk-fill composites investigated exhibited higher LT, independent of different filler content and characteristics. Although an increase in composite thickness reduced LT, the BFS of bulk-fill composites at deeper layers was not compromised.

Molecular-level spectroscopic investigations of the complexation and photodegradation of catechol to/by iron(III)

NASA Astrophysics Data System (ADS)

Al-Abadleh, Hind; Tofan-Lazar, Julia; Situm, Arthur; Slikboer, Samantha

2014-05-01

Surface water plays a crucial role in facilitating or inhibiting surface reactions in atmospheric aerosols. Little is known about the role of surface water in the complexation of organic molecules to transition metals in multicomponent aerosol systems. We will show results from real time diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) experiments for the in situ complexation of catechol to Fe(III) and its photosensitized degradation under dry and humid conditions. Catechol was chosen as a simple model for humic-like substances (HULIS) in aerosols and aged polyaromatic hydrocarbons (PAH). It has also been detected in secondary organic aerosols (SOA) formed from the reaction of hydroxyl radicals with benzene. Given the importance of the iron content in aerosols and its biogeochemistry, our studies were conducted using FeCl3. For comparison, these surface-sensitive studies were complemented with bulk aqueous ATR-FTIR, UV-vis, and HPLC measurements for structural, quantitative and qualitative information about complexes in the bulk, and potential degradation products. The implications of our studies on understanding interfacial and condensed phase chemistry relevant to multicomponent aerosols, water thin islands on buildings, and ocean surfaces containing transition metals will be discussed.

Interfacial Water-Transport Effects in Proton-Exchange Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kienitz, Brian; Yamada, Haruhiko; Nonoyama, Nobuaki

2009-11-19

It is well known that the proton-exchange membrane is perhaps the most critical component of a polymer-electrolyte fuel cell. Typical membranes, such as Nafion(R), require hydration to conduct efficiently and are instrumental in cell water management. Recently, evidence has been shown that these membranes might have different interfacial morphology and transport properties than in the bulk. In this paper, experimental data combined with theoretical simulations will be presented that explore the existence and impact of interfacial resistance on water transport for Nafion(R) 21x membranes. A mass-transfer coefficient for the interfacial resistance is calculated from experimental data using different permeation cells.more » This coefficient is shown to depend exponentially on relative humidity or water activity. The interfacial resistance does not seem to exist for liquid/membrane or membrane/membrane interfaces. The effect of the interfacial resistance is to flatten the water-content profiles within the membrane during operation. Under typical operating conditions, the resistance is on par with the water-transport resistance of the bulk membrane. Thus, the interfacial resistance can be dominant especially in thin, dry membranes and can affect overall fuel-cell performance.« less

Continuous feed, on-site composting of kitchen garbage.

PubMed

Hwang, Eung-Ju; Shin, Hang-Sik; Tay, Joo-Hwa

2002-04-01

Kitchen garbage generated at a school cafeteria was treated and stabilised in a controlled on-site composting unit for volume reduction and on-site utilisation of processed garbage. The on-site composter was fed with the garbage on a daily basis during the two-months experimental period. Compost was not removed from the unit but was entirely reused as a bulking agent in order to minimise the need for additional bulking agent and compost handling. Performance of the composter tinder this condition was investigated. Most of the easily degradable organic matter (EDM) in the garbage was biodegraded rapidly, and the final product had a low content of EDM. Lipids, total sugar, and hemi-cellulose were degraded 96%, 81%, and 66% respectively. Free air space (FAS) was higher than 0.5 all the time, so accumulation of dry matter in the unit was not significant in reducing reaction efficiency. Other reaction parameters such as pH and MC were kept within a suitable range; however, it was advisable to maintain MC at over 46%. As a result, this method of operation was able to stabilise the garbage with low sawdust demand and little compost production.

Drying and control of moisture content and dimensional changes

Treesearch

Richard Bergman

2010-01-01

The discussion in this chapter is concerned with moisture content determination, recommended moisture content values, drying methods, methods of calculating dimensional changes, design factors affecting such changes in structures, and moisture content control during transit, storage, and construction. Data on green moisture content, fiber saturation point, shrinkage,...

Comparison of different drying methods on the physical properties, bioactive compounds and antioxidant activity of raspberry powders.

PubMed

Si, Xu; Chen, Qinqin; Bi, Jinfeng; Wu, Xinye; Yi, Jianyong; Zhou, Linyan; Li, Zhaolu

2016-04-01

Dehydration has been considered as one of the traditional but most effective techniques for perishable fruits. Raspberry powders obtained after dehydration can be added as ingredients into food formulations such as bakery and dairy products. In this study, raspberry powders obtained by hot air drying (HAD), infrared radiation drying (IRD), hot air and explosion puffing drying (HA-EPD), infrared radiation and microwave vacuum drying (IR-MVD) and freeze drying (FD) were compared on physical properties, bioactive compounds and antioxidant activity. Drying techniques affected the physical properties, bioactive compounds and antioxidant activity of raspberry powders greatly. FD led to significantly higher (P < 0.05) values of water solubility (45.26%), soluble solid (63.46%), hygroscopicity (18.06%), color parameters and anthocyanin retention (60.70%) of raspberry powder compared with other drying methods. However, thermal drying techniques, especially combined drying methods, were superior to FD in final total polyphenol content, total flavonoid content and antioxidant activity. The combined drying methods, especially IR-MVD, showed the highest total polyphenol content (123.22 g GAE kg(-1) dw) and total flavonoid content (0.30 g CAE kg(-1) dw). Additionally, IR-MVD performed better in antioxidant activity retention. Overall, combined drying methods, especially IR-MVD, were found to result in better quality of raspberry powders among the thermal drying techniques. IR-MVD could be recommended for use in the drying industry because of its advantages in time saving and nutrient retention. © 2015 Society of Chemical Industry.

Effect of different pretreatments on dried chilli (Capsicum annum L.) quality

NASA Astrophysics Data System (ADS)

Anoraga, S. B.; Sabarisman, I.; Ainuri, M.

2018-03-01

Chilli (Capsicum annum L.) has significant price fluctuation. When the chilli price is declined, it causes food waste from unsold chilli. Therefore, drying chilli is a solution for this condition. Futhermore, it can be processed for various product like chilli powder, chilli sauce, etc. The aim of this study was to investigate the effect of different pretreatments on dried chilli quality. Chilli was blenched with hot water and steam before drying. The purpose of this pretreatments is to inactivate enzyme that prevents color and vitamin C losses. The quality parameters were moisture content, colour, vitamin C content, and capsaicin. Changes were observed by gravimetri method for moisture content, chromameter in L* a * b * colour model, and iodine titration for vitamin C. After drying for 20 hours at 60°C, chilli with steam blanching pretreatment dried rapidly than other samples. Unpretreated chilli had higher vitamin C content and better color than blanched chilli.

Total phenolics content, anthocyanins, and dietary fiber content of apple pomace powders produced by vacuum-belt drying.

PubMed

Yan, Huitong; Kerr, William L

2013-04-01

Apple pomace is a waste material from apple juice processing, and contains significant amounts of dietary fiber and phytochemicals. Many of these compounds may be degraded post-pressing and during drying operations. Continuous vacuum-belt drying (VBD) was studied as a means of drying and maintaining quality of apple pomace. The color and chemical properties of samples dried by vacuum-belt drying at different temperatures were evaluated including total phenolics content (TPC), monomeric anthocyanins (TMA) and dietary fiber content (TDF). VBD powders were pale golden yellow, and those dried at 80°C did not differ in L*, a* and b* values from freeze-dried powders. VBD pomace had 44.9 to 51.9 g gallic acid equivalents kg(-1) TPC, with greatest retention for pomace dried at 80 and 95°C. TPC for pomace dried at 80 or 95°C was not significantly different from that for freeze-dried pomace. TMA levels (74.0 mg C3G kg(-1), where C3G is cyanidine 3-O-glucoside equivalents) were highest in pomace vacuum dried at 80°C. TDF ranged from 442 to 495 g kg(-1) in vacuum-dried pomace and was not significantly different from TDF of freeze-dried poamce (480 g kg(-1)). In all cases, TPC, TMA and TDF were higher in VBD pomace than in freeze-dried whole apple, while VBD pomace prepared at 80 or 95°C had fiber and phytochemical levels similar to freeze-dried powders. © 2012 Society of Chemical Industry.

Effect of mixing time, freeze-drying and baking on phenolics, anthocyanins and antioxidant capacity of raspberry juice during processing of muffins.

PubMed

Rosales-Soto, Maria U; Powers, Joseph R; Alldredge, J Richard

2012-05-01

Consumption of baked products constitutes an important part of a daily breakfast considering that people are continually grabbing meals on the go. Among baked products, muffins rank third in breakfast products and attract a broad range of consumers. Incorporation of red raspberry juice into muffins can add value to the product while preserving health benefits to the consumer. The purpose of this study was to evaluate the effect of mixing time, freeze-drying and baking on the phenolic and anthocyanin contents and antioxidant capacity of raspberry juice during the preparation of muffins. Freeze-drying of raspberry batters reduced their phenolic content and antioxidant capacity regardless of mixing time. Non-freeze-dried raspberry batter mixed for 5 min had the highest phenolic content (0.88 mg gallic acid equivalent g(-1) dry matter (DM)). Non-freeze-dried raspberry muffins had the highest antioxidant capacity (0.041 µmol Trolox equivalent g(-1) DM). Freeze-dried raspberry batters mixed for 5 and 10 min had the highest anthocyanin content (0.065 mg cyanidin-3-glucoside g(-1) DM). Baking reduced the anthocyanin content of both non-freeze-dried and freeze-dried raspberry muffins. Despite the reduction in valuable compounds, muffin is a vehicle for the delivery of these compounds. Copyright © 2012 Society of Chemical Industry.

Toxicity of silver and copper to Cucurbita pepo: differential effects of nano and bulk-size particles.

PubMed

Musante, Craig; White, Jason C

2012-09-01

The phytotoxicity of bulk and nanoparticle Cu and Ag was directly compared. NP Ag reduced biomass and transpiration by 66-84% when compared with bulk Ag. The Ag ion concentration was 4.4-10-times greater in NP than bulk particle solutions. The Cu ion concentration was 1.4-4.4-times greater in bulk than NP amended solutions. Humic acid (50 mg/L) decreased the ion content of bulk Cu solution by 38-42% but increased ion Cu content of NP solutions by 1.4-2.9 times. Bulk and NP Cu were highly phytotoxic; growth and transpiration were reduced by 60-70% relative to untreated controls. NP Cu phytotoxicity was unaffected by solution type, but humic acid (50 mg/L) completely alleviated phytotoxicity caused by bulk Cu. The data demonstrate differential toxicity of Ag NP relative to bulk Ag. The finding that humic acid and solution chemistry differentially impact bulk and NP behavior highlights the importance of evaluating nanoparticles under environmentally relevant conditions. Copyright © 2010 Wiley Periodicals, Inc.

Forest composition modifies litter dynamics and decomposition in regenerating tropical dry forest.

PubMed

Schilling, Erik M; Waring, Bonnie G; Schilling, Jonathan S; Powers, Jennifer S

2016-09-01

We investigated how forest composition, litter quality, and rainfall interact to affect leaf litter decomposition across three successional tropical dry forests in Costa Rica. We monitored litter stocks and bulk litter turnover in 18 plots that exhibit substantial variation in soil characteristics, tree community structure, fungal communities (including forests dominated by ecto- or arbuscular mycorrhizal host trees), and forest age. Simultaneously, we decomposed three standard litter substrates over a 6-month period spanning an unusually intense drought. Decay rates of standard substrates depended on the interaction between litter identity and forest type. Decomposition rates were correlated with tree and soil fungal community composition as well as soil fertility, but these relationships differed among litter types. In low fertility soils dominated by ectomycorrhizal oak trees, bulk litter turnover rates were low, regardless of soil moisture. By contrast, in higher fertility soils that supported mostly arbuscular mycorrhizal trees, bulk litter decay rates were strongly dependent on seasonal water availability. Both measures of decomposition increased with forest age, as did the frequency of termite-mediated wood decay. Taken together, our results demonstrate that soils and forest age exert strong control over decomposition dynamics in these tropical dry forests, either directly through effects on microclimate and nutrients, or indirectly by affecting tree and microbial community composition and traits, such as litter quality.

An evaluation of fluid bed drying of aqueous granulations.

PubMed

Hlinak, A J; Saleki-Gerhardt, A

2000-01-01

The purpose of the work described was twofold: (a) to apply heat and mass balance approaches to evaluate the fluid bed drying cycle of an aqueous granulation, and (b) to determine the effect of the temperature and relative humidity of the drying air on the ability to meet a predetermined moisture content specification. Water content determinations were performed using Karl Fischer titration, and Computrac and Mark 1 moisture analyzers. The water vapor sorption isotherms were measured using a gravimetric moisture sorption apparatus with vacuum-drying capability. Temperature, relative humidity, and air flow were measured during the drying cycle of a production-scale fluid bed dryer. Heat and mass balance equations were used to calculate the evaporation rates. Evaporation rates calculated from heat and mass balance equations agreed well with the experimental data, whereas equilibrium moisture content values provided useful information for determination of the upper limit for inlet air humidity. Increasing the air flow rate and inlet temperature reduced the drying time through the effect on the primary driving force. As expected, additional drying of granules during the equilibration period did not show a significant impact on reducing the final moisture content of granules. Reducing the drying temperature resulted in measurement of higher equilibrium moisture content for the granules, which was in good agreement with the water vapor sorption data. Heat and mass balance equations can be used to successfully model the fluid bed drying cycle of aqueous granulations. The water vapor sorption characteristics of granules dictate the final moisture content at a given temperature and relative humidity.

Dynamics of soil organic carbon in density fractions during post-agricultural succession over two lithology types, southwest China.

PubMed

Wen, Li; Li, Dejun; Chen, Hao; Wang, Kelin

2017-10-01

Agricultural abandonment has been proposed as an effective way to enhance soil organic carbon (SOC) sequestration. Nevertheless, SOC sequestration in the long term is largely determined by whether the stable SOC fractions will increase. Here the dynamics of SOC fractions during post-agricultural succession were investigated in a karst region, southwest China using a space-for-time substitution approach. Cropland, grassland, shrubland and secondary forest were selected from areas underlain by dolomite and limestone, respectively. Density fractionation was used to separate bulk SOC into free light fraction (FLFC) and heavy fraction (HFC). FLFC contents were similar over dolomite and limestone, but bulk SOC and HFC contents were greater over limestone than over dolomite. FLFC content in the forest was greater than in the other vegetation types, but bulk SOC and HFC contents increased from the cropland through to the forest for areas underlain by dolomite. The contents of bulk SOC and its fractions were similar among the four vegetation types over limestone. The proportion of FLFC in bulk SOC was higher over dolomite than over limestone, but the case was inverse for the proportion of HFC, indicating SOC over limestone was more stable. However, the proportions of both FLFC and HFC were similar among the four vegetation types, implying that SOC stability was not changed by cropland conversion. Exchangeable calcium explained most of the variance of HFC content. Our study suggests that lithology not only affects SOC content and its stability, but modulates the dynamics of SOC fractions during post-agricultural succession. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of Total Solids and Ash in Algal Biomass: Laboratory Analytical Procedure (LAP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Wychen, Stefanie; Laurens, Lieve M. L.

2016-01-13

This procedure describes the methods used to determine the amount of moisture or total solids present in a freeze-dried algal biomass sample, as well as the ash content. A traditional convection oven drying procedure is covered for total solids content, and a dry oxidation method at 575 deg. C is covered for ash content.

Effect of fermentation and drying on cocoa polyphenols.

PubMed

Albertini, Barbara; Schoubben, Aurélie; Guarnaccia, Davide; Pinelli, Filippo; Della Vecchia, Mirco; Ricci, Maurizio; Di Renzo, Gian Carlo; Blasi, Paolo

2015-11-18

Cocoa seed polyphenols have demonstrated interesting beneficial effects in humans. Most polyphenols contained in fresh seeds are chemically modified during fermentation, drying, and cocoa powder or chocolate production. The improvement of these procedures to obtain a high-polyphenol-content cocoa is highly desirable. To this aim, a field investigation on the effect of fermentation and natural drying on fine flavor National cocoa (cacao Nacional) was performed. Cocoa seeds were fermented for 6 days and, every day, samples were sun-dried and analyzed for polyphenol content and antioxidant power. During the first 2 days of fermentation, Folin-Ciocalteu and FRAP tests evidenced a significant reduction of polyphenol content and antioxidant capacity, respectively. Changes during the following days of fermentation were less significant. Epicatechin, the most studied member of the catechin family, followed a similar pathway of degradation. Data confirmed the high impact of fermentation and drying on cocoa seed polyphenols. Fermentation and drying are, on the one hand, necessary to obtain cocoa flavor and palatability but, on the other hand, are responsible for greatly compromising polyphenol content. To obtain high-polyphenol-content cocoa, the existing fermentation, drying, and manufacturing protocols should be scientifically reviewed to understand and modify the critical steps.

Campomanesia adamantium (Cambess.) O. Berg seed desiccation: influence on vigor and nucleic acids.

PubMed

Dresch, Daiane M; Masetto, Tathiana E; Scalon, Silvana P Q

2015-01-01

The aim of this study was to evaluate the sensitivity of Campomanesia adamantium seeds to desiccation by drying in activated silica gel (fast) and under laboratory conditions (slow). To assess the sensitivity of the seeds to desiccation, we used drying with silica gel and drying under laboratory conditions (25 °C), in order to obtain seeds with moisture content of 45, 35, 30, 25, 20, 15, 10 and 5%. The physiological potential of the seeds after desiccation was evaluated by measuring primary root protrusion, percentage of normal seedlings, germination seed index, seedling length, total seedling dry mass, electrical conductivity and DNA and RNA integrities. The C. adamantium seeds were sensitive to desiccation and to a reduction in moisture content to 21.1% or less by desiccation using silica gel, and to 17.2% or less by desiccation under laboratory conditions; impairment of the physiological potential of the seeds was observed at these low moisture content levels. The integrity of the seed genomic DNA was not affected after drying seeds in the two methods. However, drying in silica gel to 4.5% moisture content and drying under laboratory conditions to 5.4% moisture content resulted in the loss of seed RNA integrity.

Total solids content: a key parameter of metabolic pathways in dry anaerobic digestion

PubMed Central

2013-01-01

Background In solid-state anaerobic digestion (AD) bioprocesses, hydrolytic and acidogenic microbial metabolisms have not yet been clarified. Since these stages are particularly important for the establishment of the biological reaction, better knowledge could optimize the process performances by process parameters adjustment. Results This study demonstrated the effect of total solids (TS) content on microbial fermentation of wheat straw with six different TS contents ranging from wet to dry conditions (10 to 33% TS). Three groups of metabolic behaviors were distinguished based on wheat straw conversion rates with 2,200, 1,600, and 1,400 mmol.kgVS-1 of fermentative products under wet (10 and 14% TS), dry (19 to 28% TS), and highly dry (28 to 33% TS) conditions, respectively. Furthermore, both wet and dry fermentations showed acetic and butyric acid metabolisms, whereas a mainly butyric acid metabolism occurred in highly dry fermentation. Conclusion Substrate conversion was reduced with no changes of the metabolic pathways until a clear limit at 28% TS content, which corresponded to the threshold value of free water content of wheat straw. This study suggested that metabolic pathways present a limit of TS content for high-solid AD. PMID:24261971

Fractal Feature of Particle-Size Distribution in the Rhizospheres and Bulk Soils during Natural Recovery on the Loess Plateau, China

PubMed Central

Song, Zilin; Zhang, Chao; Liu, Guobin; Qu, Dong; Xue, Sha

2015-01-01

The application of fractal geometry to describe soil structure is an increasingly useful tool for better understanding the performance of soil systems. Only a few studies, however, have focused on the structure of rhizospheric zones, where energy flow and nutrient recycling most frequently occur. We used fractal dimensions to investigate the characteristics of particle-size distribution (PSD) in the rhizospheres and bulk soils of six croplands abandoned for 1, 5, 10, 15, 20, and 30 years on the Loess Plateau of China and evaluated the changes over successional time. The PSDs of the rhizospheres and the fractal dimensions between rhizosphere soil and bulk soils during the natural succession differed significantly due to the influence of plant roots. The rhizospheres had higher sand (0.05–1.00 mm) contents, lower silt (<0.002 mm) contents, and lower fractal dimensions than the bulk soils during the early and intermediate successional stages (1–15 years). The fractal dimensions of the rhizosphere soil and bulk soil ranged from 2.102 to 2.441 and from 2.214 to 2.459, respectively, during the 30-year restoration. Rhizospheric clay and silt contents and fractal dimension tended to be higher and sand content tended to be lower as abandonment age increased, but the bulk soils had the opposite trend. Linear regression analysis indicated that the fractal dimensions of both the rhizospheres and bulk soils were significantly linearly correlated with clay, sand, organic-carbon, and total-nitrogen contents, with R 2 ranging from 0.526 to 0.752 (P<0.001). In conclusion, PSD differed significantly between the rhizosphere soil and bulk soil. The fractal dimension was a sensitive and useful index for quantifying changes in the properties of the different soil zones. This study will greatly aid the application of the fractal method for describing soil structure and nutrient status and the understanding of the performance of rhizospheric zones during ecological restoration. PMID:26368339

Factors influencing variation of bulk milk antibiotic residue occurrence, somatic cell count, and total bacterial count in dairy sheep flocks.

PubMed

Gonzalo, C; Carriedo, J A; García-Jimeno, M C; Pérez-Bilbao, M; de la Fuente, L F

2010-04-01

To study the variations of bulk tank milk variables in dairy ewe flocks and to identify the main target practices and flock groups to improve milk quality and safety, a total of 71,228 records of antibiotic residue (AR) and milk yield and 68,781 records of somatic cell count (SCC) and total bacterial count (TBC) were obtained over 5 yr from the same 209 dairy ewe flocks of the Assaf breed belonging to the Consortium for Ovine Promotion of Castilla-León (Spain). Based on a logistic regression model, year, month, semester, SCC, TBC, dry therapy, and milk yield significantly contributed to AR variation. High SCC was associated with increased AR violations. When antibiotic dry therapy was implemented, AR occurrence was higher than when this practice was not used. A polynomial monthly distribution throughout the year was observed for AR occurrence; the highest values were in autumn, coinciding with low milk yields per flock. Yearly occurrences drastically diminished from 2004 (1.36%) to 2008 (0.30%), probably as a result of effective educational programs. The mixed-model ANOVA of factors influencing variation in SCC and TBC indicated that year, month, AR, dry therapy group, milking type, and year interactions were significant variation factors for SCC and TBC; mathematical model accounted for 74.1 and 35.4% of total variance for each variable, respectively. Differences in management and hygiene practice caused significant SCC and TBC variations among flocks and within flocks throughout the 5-yr study. Over time, continuously dry treated flocks showed lower logSCC (5.80) and logTBC (4.92) than untreated (6.10 and 5.18, respectively) or discontinuously dry treated (6.01 and 5.05, respectively) flocks. Continuously dry treated flocks had lower AR occurrences than did discontinuously dry treated flocks. As a whole, AR occurrence and SCC and TBC bulk tank milk variables can be used for monitoring mammary health and milk hygiene and safety in dairy sheep throughout time. Copyright (c) 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

Facilities Management Guide for Asbestos and Lead

DTIC Science & Technology

2004-11-01

equipment such as HEPA filtered power tools, portable welding exhaust systems, and paint removal equipment when work disturbs lead. Do not dry sweep ...sampling and analysis of [______] paint bulk and wipe samples by atomic absorption spectrophotometry (AA) or anodic stripping voltametry (ASV...analysis. e. All bulk (destructive) collected for lead shall be analyzed by atomic absorption spectrophotometry (AA) or anodic stripping voltametry

Occurrence of ochratoxin a contamination and detection of ochratoxigenic aspergillus species in retail samples of dried fruits and nuts

USDA-ARS?s Scientific Manuscript database

Ochratoxin A (OTA) is a mycotoxin produced by several species of Aspergillus and Penicillium and is a potential contaminant of a wide variety of food products. To determine the incidence of OTA contamination in dried fruits and tree nuts, retail packaged and bulk raisins, dates, figs, prunes, almon...

Air-drying of cells, the novel conditions for stimulated synthesis of triacylglycerol in a Green Alga, Chlorella kessleri.

PubMed

Shiratake, Takuma; Sato, Atsushi; Minoda, Ayumi; Tsuzuki, Mikio; Sato, Norihiro

2013-01-01

Triacylglycerol is used for the production of commodities including food oils and biodiesel fuel. Microalgae can accumulate triacylglycerol under adverse environmental conditions such as nitrogen-starvation. This study explored the possibility of air-drying of green algal cells as a novel and simple protocol for enhancement of their triacylglycerol content. Chlorella kessleri cells were fixed on the surface of a glass fibre filter and then subjected to air-drying with light illumination. The dry cell weight, on a filter, increased by 2.7-fold in 96 h, the corresponding chlorophyll content ranging from 1.0 to 1.3-fold the initial one. Concomitantly, the triacylglycerol content remarkably increased to 70.3 mole% of fatty acids and 15.9% (w/w), relative to total fatty acids and dry cell weight, respectively, like in cells starved of nitrogen. Reduction of the stress of air-drying by placing the glass filter on a filter paper soaked in H2O lowered the fatty acid content of triacylglycerol to 26.4 mole% as to total fatty acids. Moreover, replacement of the H2O with culture medium further decreased the fatty acid content of triacylglycerol to 12.2 mole%. It thus seemed that severe dehydration is required for full induction of triacylglycerol synthesis, and that nutritional depletion as well as dehydration are crucial environmental factors. Meanwhile, air-drying of Chlamydomonas reinhardtii cells increased the triacylglycerol content to only 37.9 mole% of fatty acids and 4.8% (w/w), relative to total fatty acids and dry cell weight, respectively, and a marked decrease in the chlorophyll content, on a filter, of 33%. Air-drying thus has an impact on triacylglycerol synthesis in C. reinhardtii also, however, the effect is considerably limited, owing probably to instability of the photosynthetic machinery. This air-drying protocol could be useful for the development of a system for industrial production of triacylglycerol with appropriate selection of the algal species.

The Effect of Fermentation and Drying on Clicanthus Nutans Lindai Extract Chemical Constituents and Bioactivity

NASA Astrophysics Data System (ADS)

Lee, Y. Y.; Teh, P. S.; Kumaresan, S.; Tiong, C. H.

2017-06-01

In this study, two processes (fermentation and drying) were conducted on Clicanthus Nutans Lindau, which is well-known for its antioxidant activities. The aim of this research is to investigate the effects of these processes towards the Total Phenolic Content (TPC), antioxidant activity and the crude yield of the leaves. For the fermentation process, the fermentation time is varied for 6, 12, 24, 48 and 72 hours. For drying, oven drying (40, 45 and 50°C, freeze-drying and shade drying are investigated. Blanching was also conducted for oven dried samples (90°C for 1 minute). It was found that 12 hours fermentation produced the highest yield corresponding to Total Phenolic Content at 0.33 while 6 hours fermentation produced the highest Antioxidant Activity and yield at 2.218 x 10-10 mg/mL and 0.64 . On the other hand, 48 hours fermentation produced the highest overall extract yield at 0.64 . Analysis for antioxidant activity was carried out using 2,2-diphenyl-1-picrylhydrazyl (DPPH) and Folin-Ciocalteau method for Total Phenolic Content. Thermal inactivation kinetics (blanching) has been investigated for oven drying samples. Results showed that 40°C oven drying and 50°C oven drying with blanching has better retention of bioactive constituents. Blanching has no significant effect on phenolic content but has increased the crude extract for higher temperature oven drying. It has no positive effect on antioxidant activity. Drying is also a better processing method compared to fermentation as drying has slightly favorable results in all three aspects. Through comparison with extraction time of 60 minutes for 40°C oven drying and 6 hour fermented samples, yield of total phenolic content and overall yield of oven dried sample is higher than fermented sample by 4.14 and 0.39 respectively as well as showing better antioxidant activity.

Modelling digestive constraints in non-ruminant and ruminant foregut-fermenting mammals.

PubMed

Munn, Adam J; Streich, W Jürgen; Hummel, Jürgen; Clauss, Marcus

2008-09-01

It has been suggested that large foregut-fermenting marsupial herbivores, the kangaroos and their relatives, may be less constrained by food intake limitations as compared with ruminants, due mainly to differences in their digestive morphology and management of ingesta particles through the gut. In particular, as the quality of forage declines with increasing contents of plant fibre (cellulose, hemicelluloses and lignin; measured as neutral-detergent fibre, NDF), the tubiform foregut of kangaroos may allow these animals to maintain food intakes more so than ruminants like sheep, which appear to be limited by fibrous bulk filling the foregut and truncating further ingestion. Using available data on dry matter intake (DMI, g kg(-0.75) d(-1)), ingesta mean retention time (MRT, h), and apparent digestibility, we modelled digestible dry matter intake (DDMI) and digestible energy intake (DEI) by ruminant sheep (Ovis aries) and by the largest marsupial herbivore, the red kangaroo (Macropus rufus). Sheep achieved higher MRTs on similar DMIs, and hence sheep achieved higher DDMIs for any given level of DMI as compared with kangaroos. Interestingly, MRT declined in response to increasing DMI in a similar pattern for both species, and the association between DMI and plant NDF contents did not support the hypothesis that kangaroos are less affected by increasing fibre relative to sheep. However, when DEI was modelled according to DDMIs and dietary energy contents, we show that the kangaroos could meet their daily maintenance energy requirements (MER) at lower levels of DMI and on diets with higher fibre contents compared with sheep, due largely to the kangaroos' lower absolute maintenance and basal energy metabolisms compared with eutherians. These results suggest that differences in the metabolic set-point of different species can have profound effects on their nutritional niche, even when their digestive constraints are similar, as was the case for these ruminant and non-ruminant foregut fermenters.

Alternate wetting and drying decreases methylmercury in flooded rice (Oryza sativa) systems

USGS Publications Warehouse

Tanner, K. Christy; Windham-Myers, Lisamarie; Marvin-DiPasquale, Mark C.; Fleck, Jacob; Linquist, Bruce A.

2018-01-01

In flooded soils, including those found in rice (Oryza sativa L.) fields, microbes convert inorganic Hg to more toxic methylmercury (MeHg). Methylmercury is accumulated in rice grain, potentially affecting health. Methylmercury in rice field surface water can bioaccumulate in wildlife. We evaluated how introducing aerobic periods into an otherwise continuously flooded rice growing season affects MeHg dynamics. Conventional continuously flooded (CF) rice field water management was compared with alternate wetting and drying, where irrigation was stopped twice during the growing season, allowing soil to dry to 35% volumetric moisture content, at which point plots were reflooded (AWD-35). Methylmercury studies began at harvest in Year 3 and throughout Year 4 of a 4-yr replicated field experiment. Bulk soil, water, and plant samples were analyzed for MeHg and total Hg (THg), and iron (Fe) speciation was measured in soil samples. Rice grain yield over 4 yr did not differ between treatments. Soil chemistry responded quickly to AWD-35 dry-downs, showing significant oxidation of Fe(II) accompanied by a significant reduction of MeHg concentration (76% reduction at harvest) compared with CF. Surface water MeHg decreased by 68 and 39% in the growing and fallow seasons, respectively, suggesting that the effects of AWD-35 management can last through to the fallow season. The AWD-35 treatment reduced rice grain MeHg and THg by 60 and 32%, respectively. These results suggest that the more aerobic conditions caused by AWD-35 limited the activity of Hg(II)-methylating microbes and may be an effective way to reduce MeHg concentrations in rice ecosystems.

Folic acid content in thermostabilized and freeze-dried space shuttle foods

NASA Technical Reports Server (NTRS)

Lane, H. W.; Nillen, J. L.; Kloeris, V. L.

1995-01-01

This study was designed to determine whether freeze-dried and thermostabilized foods on a space shuttle contain adequate folate and to investigate any effects of freeze-drying on folacin. Frozen vegetables were analyzed after three states of processing: thawed; cooked; and rehydrated. Thermostabilized items were analyzed as supplied with no further processing. Measurable folate decreased in some freeze-dried vegetables and increased in others. Folacin content of thermostabilized food items was comparable with published values. We concluded that although the folacin content of some freeze-dried foods was low, adequate folate is available from the shuttle menu to meet RDA guidelines.

Method for predicting dry mechanical properties from wet wood and standing trees

DOEpatents

Meglen, Robert R.; Kelley, Stephen S.

2003-08-12

A method for determining the dry mechanical strength for a green wood comprising: illuminating a surface of the wood to be determined with light between 350-2,500 nm, the wood having a green moisture content; analyzing the surface using a spectrometric method, the method generating a first spectral data, and using a multivariate analysis to predict the dry mechanical strength of green wood when dry by comparing the first spectral data with a calibration model, the calibration model comprising a second spectrometric method of spectral data obtained from a reference wood having a green moisture content, the second spectral data correlated with a known mechanical strength analytical result obtained from a reference wood when dried and having a dry moisture content.

Quality of dry-cured ham compared with quality of dry-cured shoulder.

PubMed

Reina, Raquel; Sánchez del Pulgar, José; Tovar, Jorge; López-Buesa, Pascual; García, Carmen

2013-08-01

The physicochemical and sensory properties of 30 dry-cured hams and 30 dry-cured shoulders were analyzed to determine the relationships between them. The variables used to characterize both products were: compositional parameters, instrumental texture, amino acid and fatty acid composition, and sensory profile. Despite being products from the same animal and composed mainly of fat, lean, and bone, their morphological differences determine the conditions of the processing time, which produced differences between products in most of the parameters evaluated. Dry-cured shoulders showed lower moisture content and greater instrumental hardness due to their morphology and muscular structure. Besides, these samples showed lower amino acid content according to the shorter ripening time. For the same reason, the dry-cured hams showed higher moisture content, lower instrumental hardness, and higher amino acid content. However, the differences in the muscular structure did not affect the sensory characteristics, which were more related with some compositional parameters, such as chloride, moisture, and amino acid content and with the length of the curing process. © 2013 Extremadura University.

Effective moisture diffusivity and activation energy of rambutan seed under different drying methods to promote storage stability

NASA Astrophysics Data System (ADS)

Ahmad, So'bah; Shamsul Anuar, Mohd; Saleena Taip, Farah; Shamsudin, Rosnah; M, Siti Roha A.

2017-05-01

The effects of two drying methods, oven and microwave drying on the effective moisture diffusivity and activation energy of rambutan seed were studied. Effective moisture diffusivity and activation energy are the main indicators used for moisture movement within the material. Hence, it is beneficial to determine an appropriate drying method to attain a final moisture content of rambutan seed that potentially could be used as secondary sources in the industry. An appropriate final moisture content will provide better storage stability that can extend the lifespan of the rambutan seed. The rambutan seeds were dried with two drying methods (oven and microwave) at two level of the process variables (oven temperature; 40°C and 60°C and microwave power; 250W and 1000W) at constant initial moisture contents. The result showed that a higher value of effective moisture diffusivity and less activation energy were observed in microwave drying compared to oven drying. This finding portrays microwave drying expedites the moisture removal to achieve the required final moisture content and the most appropriate drying method for longer storage stability for rambutan seed. With respect to the process variables; higher oven temperatures and lower microwave powers also exhibit similar trends. Hopefully, this study would provide a baseline data to determine an appropriate drying method for longer storage period for turning waste to by-products.

Freeze drying vs microwave drying-methods for synthesis of sinteractive thoria powders

NASA Astrophysics Data System (ADS)

Annie, D.; Chandramouli, V.; Anthonysamy, S.; Ghosh, Chanchal; Divakar, R.

2017-02-01

Thoria powders were synthesized by oxalate precipitation from an aqueous solution of the nitrate. The filtered precipitates were freeze dried or microwave dried before being calcined at 1073 K. The thoria powders obtained were characterized for crystallite size, specific surface area, bulk density, particle size distribution and residual carbon. Microstructure of the product was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Sinterability of the synthesized powders was studied by measuring the density of the sintered compacts. Powders that can be consolidated and sintered to densities ∼96% theoretical density (TD) at 1773 K were obtained.

The Mechanism of Freezing Injury in Xylem of Winter Apple Twigs 1

PubMed Central

Quamme, H.; Weiser, C. J.; Stushnoff, C.

1973-01-01

In acclimated winter twigs of Haralson apple (Pyrus Malus L.), a lag in temperature during cooling at a constant rate was observed at about −41 C by differential thermal analysis. The temperature at which this low temperature exotherm occurred was essentially unaffected by the cooling rate. During thawing there was no lag in temperature (endotherm) near the temperature at which the low temperature exotherm occurred, but upon subsequent refreezing the exotherm reappeared at a somewhat higher temperature when twigs were rewarmed to at least −5 C before refreezing. These observations indicate that a small fraction of water may remain unfrozen to as low as −42 C after freezing of the bulk water in stems. The low temperature exotherm was not present in twigs freeze-dried to a water content below 8.5% (per unit fresh weight), but it reappeared when twigs were rehydrated to 20% water. When freeze-dried twigs were ground to a fine powder prior to rehydration, no exotherm was observed. Previous work has shown that the low temperature exotherm arises from xylem and pith tissues, and that injury to living cells in these tissues invariably occurs only when twigs are cooled below, but not above the temperature of the low temperature exotherm. This study revealed that the low temperature exotherm resulted from the freezing of a water fraction, that the freezing of this water was independent of the freezing of the bulk water, that the exotherm was associated with some gross structural feature but not the viability of the tissue, and that injury to living cells in the xylem and pith was closely and perhaps causally related to the initial freezing of this water. PMID:16658314

Economic characteristics of the peat deposits of Costa Rica: preliminary study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, A.D. Malavassi, L.; Raymond, R. Jr.; Mora, S.

1985-01-01

Recent field and laboratory studies have established the presence of numerous extensive peat deposits in Costa Rica. Three of these were selected for initial investigation: (1) the cloud-forest histosols of the Talamanca Mountain Range; (2) the Rio Medio Queso flood plain deposits near the northern Costa Rican border; and (3) a tropical jungle swamp deposit on the northeastern coastal plain. In the Talamanca area, 29 samples were collected from eight sites. Due to the high moisture and cool temperatures of the cloud forest, the peats in this area form blanket-like deposits (generally <1 meter thick) over a wide area (>150more » km/sup 2/). These peats are all highly decomposed (avg. 28% fiber), high in ash (avg. 21%), and extensively bioturbated. Relative to all other sites visited, these peats are lowest in moisture (avg. 84%), pH (avg. 4.4), fixed carbon (avg. 23%), and sulfur (avg. 0.2%). However, they have the highest bulk densities (avg. 0.22 g/cc), volatile matter contents (avg. 55%), and nitrogen. Their heating value averaged 7700 BTUs/lb., dry. In the Rio Medio Queso area, 28 samples were collected, representing one transect of the 70 km/sup 2/ flood plain. The peats here occurred in several layers (each <1-1/2 meters thick), interfingering with river flood plain sediments. These peats have the highest calorific values (avg. 8000 BTUs/lb., dry), fixed carbon (avg. 30%), and ash (avg. 22%) and have an average pH of 5.4 and a bulk density of 0.20 g/cc. These results represent only the first part of a long-term, extensive survey of Costa Rica's peat resources. However, they suggest that large, economically-significant peat deposits may be present in this country. 5 refs., 8 figs., 4 tabs.« less

De-coupling seasonal changes in water content and dry matter to predict live conifer foliar moisture content

Treesearch

W. Matt Jolly; Ann M. Hadlow; Kathleen Huguet

2014-01-01

Live foliar moisture content (LFMC) significantly influences wildland fire behaviour. However, characterising variations in LFMC is difficult because both foliar mass and dry mass can change throughout the season. Here we quantify the seasonal changes in both plant water status and dry matter partitioning. We collected new and old foliar samples from Pinus contorta for...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

Inhibitory effect of burdock leaves on elastase and tyrosinase activity.

PubMed

Horng, Chi-Ting; Wu, Hsing-Chen; Chiang, Ni-Na; Lee, Chiu-Fang; Huang, Yu-Syuan; Wang, Hui-Yun; Yang, Jai-Sing; Chen, Fu-An

2017-10-01

Burdock ( Arctium lappa L.) leaves generate a considerable amount of waste following burdock root harvest in Taiwan. To increase the use of burdock leaves, the present study investigated the optimal methods for producing burdock leaf extract (BLE) with high antioxidant polyphenolic content, including drying methods and solvent extraction concentration. In addition, the elastase and tyrosinase inhibitory activity of BLE was examined. Burdock leaves were dried by four methods: Shadow drying, oven drying, sun drying and freeze-drying. The extract solution was then subjected to total polyphenol content analysis and the method that produced BLE with the highest amount of total antioxidant components was taken forward for further analysis. The 1,1-diphenyl-2-pycrylhydrazyl scavenging, antielastase and antityrosinase activity of the BLE were measured to enable the evaluation of the antioxidant and skin aging-associated enzyme inhibitory activities of BLE. The results indicated that the total polyphenolic content following extraction with ethanol (EtOH) was highest using the freeze-drying method, followed by the oven drying, shadow drying and sun drying methods. BLE yielded a higher polyphenol content and stronger antioxidant activity as the ratio of the aqueous content of the extraction solvent used increased. BLE possesses marked tyrosinase and elastase inhibitory activities, with its antielastase activity notably stronger compared with its antityrosinase activity. These results indicate that the concentration of the extraction solvent was associated with the antioxidant and skin aging-associated enzyme inhibitory activity of BLE. The reactive oxygen species scavenging theory of skin aging may explain the tyrosinase and elastase inhibitory activity of BLE. In conclusion, the optimal method for obtaining BLE with a high antioxidant polyphenolic content was freeze-drying followed by 30-50% EtOH extraction. In addition, the antielastase and antityrosinase activities of the BLE produced may be aid in the development of skincare products with antiwrinkle and skin-evening properties.

Inhibitory effect of burdock leaves on elastase and tyrosinase activity

PubMed Central

Horng, Chi-Ting; Wu, Hsing-Chen; Chiang, Ni-Na; Lee, Chiu-Fang; Huang, Yu-Syuan; Wang, Hui-Yun; Yang, Jai-Sing; Chen, Fu-An

2017-01-01

Burdock (Arctium lappa L.) leaves generate a considerable amount of waste following burdock root harvest in Taiwan. To increase the use of burdock leaves, the present study investigated the optimal methods for producing burdock leaf extract (BLE) with high antioxidant polyphenolic content, including drying methods and solvent extraction concentration. In addition, the elastase and tyrosinase inhibitory activity of BLE was examined. Burdock leaves were dried by four methods: Shadow drying, oven drying, sun drying and freeze-drying. The extract solution was then subjected to total polyphenol content analysis and the method that produced BLE with the highest amount of total antioxidant components was taken forward for further analysis. The 1,1-diphenyl-2-pycrylhydrazyl scavenging, antielastase and antityrosinase activity of the BLE were measured to enable the evaluation of the antioxidant and skin aging-associated enzyme inhibitory activities of BLE. The results indicated that the total polyphenolic content following extraction with ethanol (EtOH) was highest using the freeze-drying method, followed by the oven drying, shadow drying and sun drying methods. BLE yielded a higher polyphenol content and stronger antioxidant activity as the ratio of the aqueous content of the extraction solvent used increased. BLE possesses marked tyrosinase and elastase inhibitory activities, with its antielastase activity notably stronger compared with its antityrosinase activity. These results indicate that the concentration of the extraction solvent was associated with the antioxidant and skin aging-associated enzyme inhibitory activity of BLE. The reactive oxygen species scavenging theory of skin aging may explain the tyrosinase and elastase inhibitory activity of BLE. In conclusion, the optimal method for obtaining BLE with a high antioxidant polyphenolic content was freeze-drying followed by 30–50% EtOH extraction. In addition, the antielastase and antityrosinase activities of the BLE produced may be aid in the development of skincare products with antiwrinkle and skin-evening properties. PMID:28912875

Application of Glass Fiber Waste Polypropylene Aggregate in Lightweight Concrete – thermal properties

NASA Astrophysics Data System (ADS)

Citek, D.; Rehacek, S.; Pavlik, Z.; Kolisko, J.; Dobias, D.; Pavlikova, M.

2018-03-01

Actual paper focus on thermal properties of a sustainable lightweight concrete incorporating high volume of waste polypropylene aggregate as partial substitution of natural aggregate. In presented experiments a glass fiber reinforced polypropylene (GFPP) which is a by-product of PP tubes production, partially substituted fine natural silica aggregate in 10, 20, 30, 40 and 50 mass %. Results were compared with a reference concrete mix without plastic waste in order to quantify the effect of GFPP use on concrete properties. Main material physical parameters were studied (bulk density, matrix density without air content, and particle size distribution). Especially a thermal transport and storage properties of GFPP were examined in dependence on compaction time. For the developed lightweight concrete, thermal properties were accessed using transient impulse technique, where the measurement was done in dependence on moisture content (from the fully water saturated state to dry state). It was found that the tested lightweight concrete should be prospective construction material possessing improved thermal insulation function and the reuse of waste plastics in concrete composition was beneficial both from the environmental and financial point of view.

The utilization of ultisol soil for horticulture crops cultivation

NASA Astrophysics Data System (ADS)

Sumono; Parinduri, SM; Huda, N.; Ichwan, N.

2018-02-01

Ultisol soil is a marginal soil commonly used for palm oil cultivation in Indonesia, its very potential for cultivation of horticulture crops. The utilization of ultisol soil can be done with adding compost with certain proportions. The research aimed to know best proportion of ultisol soil and compost, and proportion of water concentration, and its relationship with fresh and dry weight of horticulture crops . The research was divided 3 steps. The first, mixed ultisol soil and compost with certain proportion and flooding until steady. The second, watering with different concentration to soil mixture. The last, studied its relationship with fresh and dry weight of crops. The result show that physical properties and nutrient content of ultisol soil was increasing with adding compost. SC4 (70% soil and 30% compost) is the best composition to soil mixture. Watering with different concentration show that trend decreased from reference and the bulk density and porosity decreased not significantly at the significant level ∝ = 0.05. Watering affect mass of pakcoynot significantly at the significant level ∝ = 0.05. Hence, ultisol soil was a potential marginal soil to utilizing as a media for cultivating horticulture crops.

Effect of residual water content on the physico-chemical properties of sucralfate dried gel obtained by microwave drying.

PubMed

Gainotti, Alessandro; Losi, Elena; Bettini, Ruggero; Colombo, Paolo; Sonvico, Fabio; Baroni, Daniela; Santi, Patrizia; Colombo, Gaia

2005-08-01

The purpose of this study was to investigate the physico-chemical characteristics of sucralfate humid gel dried by microwaves, in relation to the residual water content. Differential scanning calorimetry (DSC) allowed for the determination of the water state in sucralfate samples. Fourier-transform infrared (FT-IR) spectroscopy was used to monitor the changes in sucralfate gel structure induced by the microwave drying. A boundary value of total water content for sucralfate gel samples was found at 42% (w/w). Below this value only bound water was present, whereas above this value, the increase in total water was due to free water. In the physical form of gel, the strength of the coordination between sulfate anions and the positively charged aluminum hydroxide was dependent on the residual water content. The study of the sedimentation behavior of water suspensions prepared with dried sucralfate allowed for the evaluation of the retention of gel properties. We found that the microwave drying process affected the sedimentation of sucralfate dried gel suspensions independent of the residual water content: when suspensions were prepared from sucralfate dried gel powders containing more than 42% (w/w) of residual water, the sedimentation ratio was higher than 0.9. The non-gel powder suspension showed a sedimentation ratio of 0.68 +/- 0.02, whereas the sucralfate humid gel suspension did not sediment.

Dewatering Treatment Scale-up Testing Results of Hanford Tank Wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tedeschi, A.R.; May, T.H.; Bryan, W.E.

2008-07-01

This report documents CH2M HILL Hanford Group Inc. (CH2M HILL) 2007 dryer testing results in Richland, WA at the AMEC Nuclear Ltd., GeoMelt Division (AMEC) Horn Rapids Test Site. It provides a discussion of scope and results to qualify the dryer system as a viable unit-operation in the continuing evaluation of the bulk vitrification process. A 10,000 liter (L) dryer/mixer was tested for supplemental treatment of Hanford tank low activity wastes, drying and mixing a simulated non-radioactive salt solution with glass forming minerals. Testing validated the full scale equipment for producing dried product similar to smaller scale tests, and qualifiedmore » the dryer system for a subsequent integrated dryer/vitrification test using the same simulant and glass formers. The dryer system is planned for installation at the Hanford tank farms to dry/mix radioactive waste for final treatment evaluation of the supplemental bulk vitrification process. (authors)« less

Drying and control of moisture content and dimensional changes

Treesearch

William T. Simpson

1999-01-01

In the living tree, wood contains large quantities of water. As green wood dries, most of the water is removed. The moisture remaining in the wood tends to come to equilibrium with the relative humidity of the surrounding air. Correct drying, handling, and storage of wood will minimize moisture content changes that might occur after drying when the wood is in service...

Microwave sensing of moisture content and bulk density in flowing grain

USDA-ARS?s Scientific Manuscript database

Moisture content and bulk density were determined from measurement of the dielectric properties of flowing wheat kernels at a single microwave frequency (5.8 GHz). The measuring system consisted of two high-gain microwave patch antennas mounted on opposite sides of rectangular chute and connected to...

The impact of drying techniques on phenolic compound, total phenolic content and antioxidant capacity of oat flour tarhana.

PubMed

Değirmencioğlu, Nurcan; Gürbüz, Ozan; Herken, Emine Nur; Yıldız, Aysun Yurdunuseven

2016-03-01

In this study, the changes in phenolic composition, total phenolic content, and antioxidant capacity of tarhanas supplemented with oat flour (OF) at the levels of 20-100% (w/w) after three drying treatments (sun-, oven-, and microwave drying) were investigated. A total of seventeen phenolic standards have been screened in tarhanas, and the most abundant flavonol and phenolic acid compounds were kaempferol (23.62mg/g) and 3-hydroxy-4-metoxy cinnamic acid (9.60mg/g). The total phenolic content amount gradually increased with the addition of OF to tarhana, but decidedly higher total phenolic content was found in samples oven dried at 55°C as compared with other methods. The microwave- and oven dried tarhana samples showed higher TEACDPPH and TEACABTS values than those dried with the other methods, respectively, in higher OF amounts. Consequently, oven- and microwave-drying can be recommended to retain the highest for phenolic compounds as well as maximal antioxidant capacity in OF supplemented tarhana samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inhibition of the de novo synthesis of PCDD/Fs on model fly ash by sludge drying gases.

PubMed

Chen, Tong; Zhan, Ming-Xiu; Lin, Xiao-Qing; Li, Xiao-Dong; Lu, Sheng-Yong; Yan, Jian-Hua; Buekens, Alfons; Cen, Ke-Fa

2014-11-01

Sludge drying gases (SDG), evolving from drying and mild thermal decomposition (<300°C) of raw sewage sludge contain NH3 and SO2 as well as other N- and S-compounds. All of these are potential PCDD/Fs suppressants. It is indeed observed that these SDG suppress 2,3,7,8-substitued PCDD/Fs formation on Model Fly Ash (MFA) with an efficiency up to 97.6% in wt. units and 96% in I-TEQ, respectively. This suppression is strong for (the bulk of) PCDD/Fs, adsorbed on the model fly ash; conversely, sludge drying gases enhance PCDD/Fs desorption from MFA. Moreover, TCDD/Fs are suppressed least, possibly following stepwise dechlorination of higher chlorinated PCDD/Fs. Characteristics, such as the type, origins and amount of sludge, its moisture-, nitrogen- and sulfur content and the nature of the thermal treatment applied are all expected to influence upon the suppression capabilities. In this study three types of dry sludge are tested and applied as suppressant in four different amounts or modes. The quality of the sludge drying gases is continuously monitored: the Gasmet results reveal that NH3 and SO2 are the most important components of SDG. The MFA reaction residue is scrutinized by Scanning Electron Microscope (SEM) and Energy Dispersive Spectrometer (EDS) analysis. A large number of particles attaching to the surface of model fly ash are observed by SEM. Moreover, EDS analysis reveals that part of the chlorine in MFA is carried away with the SDG and replaced by sulfur, so that eliminating chlorine may be part of the inhibition mechanism. However, further research is still needed to establish the optimum operating modes and to confirm the role of both inorganic and organic nitrogen and sulfur compounds in the suppression of PCDD/Fs formation on model fly ash. Copyright © 2014 Elsevier Ltd. All rights reserved.

Wet-dry cycles impact DOM retention in subsurface soils

NASA Astrophysics Data System (ADS)

Olshansky, Yaniv; Root, Robert A.; Chorover, Jon

2018-02-01

Transport and reactivity of carbon in the critical zone are highly controlled by reactions of dissolved organic matter (DOM) with subsurface soils, including adsorption, transformation and exchange. These reactions are dependent on frequent wet-dry cycles common to the unsaturated zone, particularly in semi-arid regions. To test for an effect of wet-dry cycles on DOM interaction and stabilization in subsoils, samples were collected from subsurface (Bw) horizons of an Entisol and an Alfisol from the Catalina-Jemez Critical Zone Observatory and sequentially reacted (four batch steps) with DOM extracted from the corresponding soil litter layers. Between each reaction step, soils either were allowed to air dry (wet-dry treatment) before introduction of the following DOM solution or were maintained under constant wetness (continually wet treatment). Microbial degradation was the dominant mechanism of DOM loss from solution for the Entisol subsoil, which had higher initial organic C content, whereas sorptive retention predominated in the lower C Alfisol subsoil. For a given soil, bulk dissolved organic C losses from solution were similar across treatments. However, a combination of Fourier transform infrared (FTIR) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopic analyses revealed that wet-dry treatments enhanced the interactions between carboxyl functional groups and soil particle surfaces. Scanning transmission X-ray microscopy (STXM) data suggested that cation bridging by Ca2+ was the primary mechanism for carboxyl association with soil surfaces. STXM data also showed that spatial fractionation of adsorbed OM on soil organo-mineral surfaces was diminished relative to what might be inferred from previously published observations pertaining to DOM fractionation on reaction with specimen mineral phases. This study provides direct evidence of the role of wet-dry cycles in affecting sorption reactions of DOM to a complex soil matrix. In the soil environment, where wet-dry cycles occur at different frequencies from site to site and along the soil profile, different interactions between DOM and soil surfaces are expected and need to be considered for the overall assessment of carbon dynamics.

Effect of processing on the biochemical contents of Acanthus montanus (Nees) T. Anderson (Acanthaceae) leaves.

PubMed

Igwe, Andrew; Eleazu, Chinedum

2018-03-01

The effect of processing on the biochemical contents of Acanthus montanus leaves was investigated. The moisture, crude protein, lipid, fiber, ash, and total carbohydrate contents of the raw vegetable were 59.15, 1.85, 2.32, 3.76, 2.04, and 34.65 g/100 g, respectively. The saponin, alkaloid, tannin, flavonoid, phenol, and anthocyanin contents of the raw vegetable were 5.35, 4.04, 1.10, 3.53, 2.87, and 1.27 g/100 g, respectively, while it contained 2.65 mg/100 g calcium, 1.14 mg/100 g magnesium, 7.66 mg/100 g potassium, 350.75 μg/g vitamin A, 50.87 mg/100 g vitamin C, and 0.25% titratable acidity. There were significant reductions ( p  < .05) in the protein, lipid, fiber, ash, saponin, alkaloid, tannin, phenol, anthocyanin, calcium, magnesium, potassium, vitamin A, vitamin C, and titratable acidity of the boiled or boiled + sun-dried A. montanus leaves; significant elevation of the moisture contents but significant reduction of the total carbohydrate contents of the boiled; and significant reduction of the moisture contents of the boiled + sun-dried vegetable compared with the raw. There were significant increases ( p  < .05) in the total carbohydrate contents of the boiled + sun-dried leaves; significant reductions ( p  < .05) in the moisture, saponin, alkaloid, and vitamins A and C contents of the sun-dried vegetable; and no significant differences ( p  > .05) in the lipid, calcium, potassium, and ash, but significant increases ( p  < .05) in the protein, crude fiber, total carbohydrates, tannins, flavonoids, phenols, anthocyanin, magnesium, and titratable acidity of the sun-dried vegetable when compared with the raw. Sun drying alone either retained or enhanced the release of some important bioactive compounds in A. montanus leaves. Furthermore, the reduced moisture content of the sun-dried vegetable together with its increased titratable acidity will make the sun-dried vegetable uninhabitable for microorganisms, thereby increasing its shelf life.

Technical Report on DOMICE Simulation Model

DTIC Science & Technology

2012-04-01

Branch GPS Global Positioning System HHO home heating oil LCA Lake Carriers’ Association MAR USCG Domestic Icebreaking Mission Analysis...cargo types considered in the module. The module groups the four types of cargo into two broader categories, namely, Home Heating Oil ( HHO ) shipments...or Non- HHO shipments. Table 11. Cargo types. Types of Cargo Cargo Group Dry Bulk Non- HHO Liquid Bulk Perishable / Food Home Heating Oil HHO

Effects of drying process on the physicochemical properties of nopal cladodes at different maturity stages.

PubMed

Contreras-Padilla, Margarita; Gutiérrez-Cortez, Elsa; Valderrama-Bravo, María Del Carmen; Rojas-Molina, Isela; Espinosa-Arbeláez, Diego Germán; Suárez-Vargas, Raúl; Rodríguez-García, Mario Enrique

2012-03-01

Chemical proximate analysis was done in order to determine the changes of nutritional characteristics of nopal powders from three different maturity stages 50, 100, and 150 days and obtained by three different drying processes: freeze dried, forced air oven, and tunnel. Results indicate that nopal powder obtained by the process of freeze dried retains higher contents of protein, soluble fiber, and fat than the other two processes. Also, freeze dried process had less effect on color hue variable. No changes were observed in insoluble fiber content, chroma and lightness with the three different drying processes. Furthermore, the soluble fibers decreased with the age of nopal while insoluble fibers and ash content shows an opposite trend. In addition, the luminosity and hue values did not show differences among the maturity stages studied. The high content of dietary fibers of nopal pad powder could to be an interesting source of these important components for human diets and also could be used in food, cosmetics and pharmaceutical industry.

Nitrite Contents in Fresh Vegetables of Different Families and Genus

NASA Astrophysics Data System (ADS)

Cui, Yuqian; Li, Xiao; Xu, Lingyi; Pang, Meixia; Qi, Jinghua; Wang, Fang

2017-12-01

The aim of this study is firstly aimed at investigating the contents of nitrite in common consumed vegetables according to families and genus classification. The vegetables were randomly collected and analyzed in quartile sampling according to GB5009.30-2016. The vegetables were analyzed by the software of Spss20.0 and statistically significant Duncan multiple comparisons. The data indicates that the nitrite contents in different families and different genus vegetables in same family were significant (P<0.01). A relatively high nitrite concentration was observed in Chenopodiaceae which is 0.5920mg/kg dry weight. A relatively low nitrite concentration was observed in Dioscoreaceae that contentration is 0.0032mg/kg dry weight. The nitrite contents of different genus are large, in which the relatively high concentration samples were red beet root (0.886mg/kg dry weight), peanut (0.7485mg/kg dry weight), corn kernels (0.7119mg/kg dry weight), Lotus root (0.592mg/kg dry weight).

Stevia rebaudiana Leaves: Effect of Drying Process Temperature on Bioactive Components, Antioxidant Capacity and Natural Sweeteners.

PubMed

Lemus-Mondaca, Roberto; Ah-Hen, Kong; Vega-Gálvez, Antonio; Honores, Carolina; Moraga, Nelson O

2016-03-01

Stevia leaves are usually used in dried state and undergo the inevitable effect of drying process that changes the quality characteristics of the final product. The aim of this study was to assess temperature effect on Stevia leaves through analysis of relevant bioactive components, antioxidant capacity and content of natural sweeteners and minerals. The drying process was performed in a convective dryer at constant temperatures ranging from 30 to 80 °C. Vitamin C was determined in the leaves and as expected showed a decrease during drying proportional to temperature. Phenolics and flavonoids were also determined and were found to increase during drying below 50 °C. Antioxidant activity was determined by DPPH and ORAC assays, and the latter showed the highest value at 40 °C, with a better correlation with the phenolics and flavonoids content. The content of eight natural sweeteners found in Stevia leaves was also determined and an increase in the content of seven of the sweeteners, excluding steviol bioside, was found at drying temperature up to 50 °C. At temperatures between 60 and 80 °C the increase in sweeteners content was not significant. Stevia leaves proved to be an excellent source of antioxidants and natural sweeteners.

Compaction Characteristics of Earth-Rock Mixtures. Report 1. Vicksburg Silty Clay and Degray Dam Clayey Sandy Gravel

DTIC Science & Technology

1973-05-01

dry density of total sample Yf = dry unit weight of finer fraction G = bulk specific gravity of coarser fraction (based on ovendry weightq). Same as G...ttl~o o 40 oe o Fig. ii. Theoretical and experimental densities of eclayey sandy gravel (GC) DeGray meterial expressions require tests performed on

Determination of the Sampler Type and Rainfall Effect on the Deposition Fluxes of the Polychlorinated Biphenyls

PubMed Central

Birgül, Askin; Tasdemir, Yücel

2012-01-01

Atmospheric concentration and deposition samples were collected between June 2008 and June 2009 in an urban sampling site Yavuzselim, Turkey. Eighty-three polychlorinated biphenyl (PCB) congeners were targeted in the collected samples. It was found that 90% of the total PCB concentration was in the gas phase. Deposition samples were collected by a wet-dry deposition sampler (WDDS) and a bulk deposition sampler (BDS). Average total deposition fluxes measured with the BDS in dry periods was 5500 ± 2400 pg/(m2day); average dry deposition fluxes measured by the WDDS in the same period were 6400 ± 3300 pg/(m2day). The results indicated that the sampler type affected the measured flux values. Bulk deposition samples were also collected in rainy periods by using the BDS and the average flux value was 8700 ± 3100 pg/(m2day). The measured flux values were lower than the values reported for the urban and industrial areas. Dry deposition velocities for the WDDS and BDS samples were calculated 0.48 ± 0.35 cm/s and 0.13 ± 0.15 cm/s, respectively. PMID:22629199

Alterations in fruit and vegetable beta-carotene and vitamin C content caused by open-sun drying, visqueen-covered and polyethylene-covered solar-dryers.

PubMed

Ndawula, J; Kabasa, J D; Byaruhanga, Y B

2004-08-01

This study investigated the effects of three drying methods (open sun drying, visqueen-covered solar dryer and polyethylene-covered solar dryer) on b-carotene and vitamin C content of edible portions of mango fruit (Mangifera indica) and cowpea leaves (Vigna unguiculata). Commercial samples were analysed for vitamin C by titrimetry and b-carotene by spectrophotometry at 450 nm. Differences in vitamin retention and loss associated with the three drying methods were assessed by analysis of variance and least significant difference (LSD) at (p<0.05. The fresh cowpea leaf b-carotene and vitamin C content was 140.9 and 164.3 mg / 100g DM respectively and decreased (p<0.05) with drying. Open sun drying method caused the greatest b-carotene and vitamin C loss (58% and 84% respectively), while the visqueen-covered solar dryer caused the least loss (34.5% and 71% respectively). Blanching cowpea leaves improved b-carotene and vitamin C retention by 15% and 7.5% respectively. The b-carotene and vitamin C content of fresh ripe mango fruit was 5.9 and 164.3 mg/100g DM respectively. Similar to effects on cowpea leaves, the mango micronutrient content decreased (p<0.05) with drying. The open sun drying method caused the greatest b-carotene (94.2%) and vitamin C (84.5%) loss, while the visqueen-covered solar dryer caused the least (73 and 53% respectively). These results show that the three solar drying methods cause significant loss of pro-vitamin A and vitamin C in dried fruits and vegetables. However, open sun drying causes the most loss and the visqueen-covered solar dryer the least, making the later a probable better drying technology for fruit and vegetable preservation. The drying technologies should be improved to enhance vitamin retention.

Modeling multidomain hydraulic properties of shrink-swell soils

NASA Astrophysics Data System (ADS)

Stewart, Ryan D.; Abou Najm, Majdi R.; Rupp, David E.; Selker, John S.

2016-10-01

Shrink-swell soils crack and become compacted as they dry, changing properties such as bulk density and hydraulic conductivity. Multidomain models divide soil into independent realms that allow soil cracks to be incorporated into classical flow and transport models. Incongruously, most applications of multidomain models assume that the porosity distributions, bulk density, and effective saturated hydraulic conductivity of the soil are constant. This study builds on a recently derived soil shrinkage model to develop a new multidomain, dual-permeability model that can accurately predict variations in soil hydraulic properties due to dynamic changes in crack size and connectivity. The model only requires estimates of soil gravimetric water content and a minimal set of parameters, all of which can be determined using laboratory and/or field measurements. We apply the model to eight clayey soils, and demonstrate its ability to quantify variations in volumetric water content (as can be determined during measurement of a soil water characteristic curve) and transient saturated hydraulic conductivity, Ks (as can be measured using infiltration tests). The proposed model is able to capture observed variations in Ks of one to more than two orders of magnitude. In contrast, other dual-permeability models assume that Ks is constant, resulting in the potential for large error when predicting water movement through shrink-swell soils. Overall, the multidomain model presented here successfully quantifies fluctuations in the hydraulic properties of shrink-swell soil matrices, and are suitable for use in physical flow and transport models based on Darcy's Law, the Richards Equation, and the advection-dispersion equation.

The iron content and ferritin contribution in fresh, dried, and toasted nori, Pyropia yezoensis.

PubMed

Masuda, Taro; Yamamoto, Ami; Toyohara, Haruhiko

2015-01-01

Iron is one of the essential trace elements for humans. In this study, the iron contents in fresh, dried, and toasted nori (Pyropia yezoensis) were analyzed. The mean iron content of fresh, dried, and toasted nori were 19.0, 22.6, and 26.2 mg/100 g (dry weight), respectively. These values were superior to other food of plant origin. Furthermore, most of the iron in nori was maintained during processing, such as washing, drying, and toasting. Then, the form of iron in fresh, dried, and toasted nori was analyzed. As a result, an iron storage protein ferritin contributed to iron storage in raw and dried nori, although the precise rate of its contribution is yet to be determined, while ferritin protein cage was degraded in the toasted nori. It is the first report that verified the ferritin contribution to iron storage in such edible macroalgae with commercial importance.

Changes on sewage sludge stability after greenhouse drying

NASA Astrophysics Data System (ADS)

Soriano-Disla, J. M.; Houot, S.; Imhoff, M.; Valentin, N.; Gómez, I.; Navarro-Pedreño, J.

2009-04-01

The progressive implementation of the Urban Waste Water Treatment Directive 91/271/EEC in all the European member states is increasing the quantities of sewage sludge requiring disposal. Sludge application onto cultivated soils as organic fertilizers allows the recycling of nutrients. The application of only dehydrated sludges has generated many problems including unpleasant odours and difficult management (regarding transport and application) related to their high water content. One way to overcome these problems, in a cheap and clean way, is the drying of sludges using the energy of the sun under greenhouse conditions. This drying may affect sludge chemical characteristics including organic matter stability and nitrogen availability, parameters which have to be controlled for the proper management of dry sludge application onto soils. For this reason, the main aim of this work was to study the impact of greenhouse drying of different sewage sludges on their organic matter stability and nitrogen availability, assessed by biochemical fractionation and mineralization assays. Three sewage sludges were sampled before (dehydrated sludges) and after greenhouse drying (dried sludges). The analyses consisted of: humidity, organic matter, mineral and organic N contents, N and C mineralization during 91-day laboratory incubations in controlled conditions, and biochemical fractionation using the Van Soest procedure. Greenhouse drying decreased the water content from 70-80% to 10% and also the odours, both of which will improve the management of the final product from the perspective of application and transport. We also found that drying reduced the organic matter content of the sludges but not the biodegradability of the remaining carbon. Organic N mineralization occurred during greenhouse drying, explaining why mineral N content tended to increase and the potential mineralization of organic nitrogen decreased after greenhouse drying. The biochemical stability did not change so much except for the one of the sludges, which experienced an important reduction. According to the results, and from a point of view of future soil applications, the balance of the drying process could be considered as positive. It is using a free, renewable and clean energy, which reduces the water content and odours of sludge, thereby improving their management. Except for the water content, there was little modification of the behaviour in soil of greenhouse dried sludges compared to the dehydrated sludges, maintaining its large amount of available nitrogen after drying. Acknowledgements: Jose. M. Soriano-Disla gratefully acknowledges the Spanish Ministry of Innovation and Culture for a research fellowship (AP2005-0320).

Mechanism of lubrication by tricresylphosphate (TCP)

NASA Technical Reports Server (NTRS)

Faut, O. D.; Wheeler, D. R.

1983-01-01

A pin-on-disk tribometer equipped with an induction heater was used to study the coefficient of friction as a function of temperature for tricresylphosphate (TCP) on continuous vacuum melted (CVM) M-50 tool steel when the TCP was present in a liquid reservoir (bulk lubrication), and when it was applied as a liquid layer directly to the disk (limited lubrication). Under limited lubrication conditions, experiments were performed in dry ( 100 ppm H2O) air, dry ( 20 ppm H2O) nitrogen, dry nitrogen with the disks heated to 700 C then cooled to room temperature before the TCP was applied and the measurements made (preheated disks), and moist nitrogen using preheated disks. When the coefficient of friction was plotted as a function of the disk temperature, the friction decreased at a characteristic temperature, T sub r whose observed values were 265 C for bulk lubrication conditions in dry air, 225 C for limited lubrication conditions in dry air, and 215 C for limited lubrication conditions in dry nitrogen. No decrease in friction was observed with preheated disks; instead a sharp failure temperature was observed at 218 C, which was taken as the temperature about which the behavior of TCP should be judged, X-ray photoelectron spectroscopy confirmed the presence of phosphate on the surface of the iron pins used in the tribometer under TCP lubrication. Depth profile studies support the idea that a chemical reaction occurs between the TCP and the metal surface at T sub r.

Application of Statistic Experimental Design to Assess the Effect of Gammairradiation Pre-Treatment on the Drying Characteristics and Qualities of Wheat

NASA Astrophysics Data System (ADS)

Yu, Yong; Wang, Jun

Wheat, pretreated by 60Co gamma irradiation, was dried by hot-air with irradiation dosage 0-3 kGy, drying temperature 40-60 °C, and initial moisture contents 19-25% (drying basis). The drying characteristics and dried qualities of wheat were evaluated based on drying time, average dehydration rate, wet gluten content (WGC), moisture content of wet gluten (MCWG)and titratable acidity (TA). A quadratic rotation-orthogonal composite experimental design, with three variables (at five levels) and five response functions, and analysis method were employed to study the effect of three variables on the individual response functions. The five response functions (drying time, average dehydration rate, WGC, MCWG, TA) correlated with these variables by second order polynomials consisting of linear, quadratic and interaction terms. A high correlation coefficient indicated the suitability of the second order polynomial to predict these response functions. The linear, interaction and quadratic effects of three variables on the five response functions were all studied.

Biogenic NO emission from a spruce forest soil in the Fichtelgebirge (Germany) under the influence of different understorey vegetation cover

NASA Astrophysics Data System (ADS)

Bargsten, A.; Andreae, M. O.; Meixner, F. X.

2009-04-01

Within the framework of the EGER project (ExchanGE processes in mountainous Regions) soil samples have been taken from the spruce forest site "Weidenbrunnen" (Fichtelgebirge, Germany) in September 2008 to determine the NO exchange in the laboratory and for a series of soil analyses. The soil was sampled below different understorey vegetation covers: young Norway spruce, moss/litter, blueberries and grass. We investigated the net NO release rate from corresponding organic layers as well as from the A horizon of respective soils. Additionally we measured pH, C/N ratio, contents of ammonium, nitrate, and organic C, bulk density, the thickness of the organic layer and the quality of the organic matter. Net NO release rates (as well as the NO production and NO consumption rates) from the soil samples were determined by a fully automated laboratory incubation & fumigation system. Purified dry air passed five dynamic incubation chambers, four containing water saturated soil samples and one reference chamber. By this procedure, the soil samples dried out slowly (within 2-6 days), covering the full range of soil moisture (0-300% gravimetric soil moisture). To quantify NO production and NO consumption rates separately, soil samples were fumigated with zero-air (approx. 0 ppb NO) and air of 133 ppb NO. The chambers were placed in a thermostatted cabinet for incubation at 10 an 20˚ C. NO and H2O concentrations at the outlet of the five dynamic chambers were measured sequentially by chemiluminescence and IR-absorption based analyzers, switching corresponding valves every two minutes. Net NO release rates were determined from the NO concentration difference between soil containing and reference chambers. Corresponding measurements of H2O mixing ratio yielded the evaporation loss of the soil samples, which (referenced to the gravimetric soil water content before and after the incubation experiment) provided the individual soil moisture contents of each soil samples during the incubation experiment. Our contribution focus net NO release rates, NO production and NO consumption rates of spruce forest soils sampled under different understorey vegetation covers. Generally, organic layers show significant higher NO production and NO consumption rates than the soils from the corresponding A horizons. Soils under the understorey vegetation cover "moos/litter" revealed the lowest NO production and NO consumption rates. Net NO release rates, NO production and NO consumption rates of soil samples obtained below the four different under- storey vegetation covers will be discussed in terms of pH, C/N ratio, contents of ammonium, nitrate, and organic C, bulk density, thickness of organic layer, as well as quality of the organic matter.

Estimation of the deoxynivalenol and moisture contents of bulk wheat grain samples by FT-NIR spectroscopy

USDA-ARS?s Scientific Manuscript database

Deoxynivalenol (DON) levels in harvested grain samples are used to evaluate the Fusarium head blight (FHB) resistance of wheat cultivars and breeding lines. Fourier transform near-infrared (FT-NIR) calibrations were developed to estimate the DON and moisture content (MC) of bulk wheat grain samples ...

The Production of a Stable Infliximab Powder: The Evaluation of Spray and Freeze-Drying for Production.

PubMed

Kanojia, Gaurav; Have, Rimko Ten; Bakker, Arjen; Wagner, Koen; Frijlink, Henderik W; Kersten, Gideon F A; Amorij, Jean-Pierre

2016-01-01

In prospect of developing an oral dosage form of Infliximab, for treatment of Crohn's disease and rheumatoid arthritis, freeze-drying (vial vs Lyoguard trays) and spray-drying were investigated as production method for stable powders. Dextran and inulin were used in combination with sucrose as stabilizing excipients. The drying processes did not affect Infliximab in these formulations, i.e. both the physical integrity and biological activity (TNF binding) were retained. Accelerated stability studies (1 month at 60°C) showed that the TNF binding ability of Infliximab was conserved in the freeze-dried formulations, whereas the liquid counterpart lost all TNF binding. After thermal treatment, the dried formulations showed some chemical modification of the IgG in the dextran-sucrose formulation, probably due to Maillard reaction products. This study indicates that, with the appropriate formulation, both spray-drying and freeze-drying may be useful for (bulk) powder production of Infliximab.

Breakage and drying behaviour of granules in a continuous fluid bed dryer: Influence of process parameters and wet granule transfer.

PubMed

De Leersnyder, F; Vanhoorne, V; Bekaert, H; Vercruysse, J; Ghijs, M; Bostijn, N; Verstraeten, M; Cappuyns, P; Van Assche, I; Vander Heyden, Y; Ziemons, E; Remon, J P; Nopens, I; Vervaet, C; De Beer, T

2018-03-30

Although twin screw granulation has already been widely studied in recent years, only few studies addressed the subsequent continuous drying which is required after wet granulation and still suffers from a lack of detailed understanding. The latter is important for optimisation and control and, hence, a cost-effective practical implementation. Therefore, the aim of the current study is to increase understanding of the drying kinetics and the breakage and attrition phenomena during fluid bed drying after continuous twin screw granulation. Experiments were performed on a continuous manufacturing line consisting of a twin-screw granulator, a six-segmented fluid bed dryer, a mill, a lubricant blender and a tablet press. Granulation parameters were fixed in order to only examine the effect of drying parameters (filling time, drying time, air flow, drying air temperature) on the size distribution and moisture content of granules (both of the entire granulate and of size fractions). The wet granules were transferred either gravimetrically or pneumatically from the granulator exit to the fluid bed dryer. After a certain drying time, the moisture content reached an equilibrium. This drying time was found to depend on the applied airflow, drying air temperature and filling time. The moisture content of the granules decreased with an increasing drying time, airflow and drying temperature. Although smaller granules dried faster, the multimodal particle size distribution of the granules did not compromise uniform drying of the granules when the target moisture content was achieved. Extensive breakage of granules was observed during drying. Especially wet granules were prone to breakage and attrition during pneumatic transport, either in the wet transfer line or in the dry transfer line. Breakage and attrition of granules during transport and drying should be anticipated early on during process and formulation development by performing integrated experiments on the granulator, dryer and mill. Copyright © 2018 Elsevier B.V. All rights reserved.

Cumulative ventilation air drying potential as an indication of dry mass content in wastewater sludge in a thin-layer solar drying facility

NASA Astrophysics Data System (ADS)

Krawczyk, Piotr

2013-12-01

Controlling low-temperature drying facilities which utilise nonprepared air is quite difficult, due to very large variability of ventilation air parameters - both in daily and seasonal cycles. The paper defines the concept of cumulative drying potential of ventilation air and presents experimental evidence that there is a relation between this parameter and condition of the dried matter (sewage sludge). Knowledge on current dry mass content in the dried matter (sewage sludge) provides new possibilities for controlling such systems. Experimental data analysed in the paper was collected in early 2012 during operation of a test solar drying facility in a sewage treatment plant in Błonie near Warsaw, Poland.

Nanoparticle motion on the surface of drying droplets

NASA Astrophysics Data System (ADS)

Zhao, Mingfei; Yong, Xin

2018-03-01

Advances in solution-based printing and surface patterning techniques for additive manufacturing demand a clear understanding of particle dynamics in drying colloidal droplets and its relationship with deposit structure. Although the evaporation-driven deposition has been studied thoroughly for the particles dispersed in the bulk of the droplet, few investigations have focused on the particles strongly adsorbed to the droplet surface. We modeled the assembly and deposition of the surface-active particles in a drying sessile droplet with a pinned contact line by the multiphase lattice Boltzmann-Brownian dynamics method. The particle trajectory and its area density profile characterize the assembly dynamics and deposition pattern development during evaporation. While the bulk-dispersed particles continuously move to the contact line, forming the typical "coffee-ring" deposit, the interface-bound particles migrate first toward the apex and then to the contact line as the droplet dries out. To understand this unexpected behavior, we resolve the droplet velocity field both in the bulk and within the interfacial region. The simulation results agree well with the analytical solution for the Stokes flow inside an evaporating droplet. At different stages of evaporation, our study reveals that the competition between the tangential surface flow and the downward motion of the evaporating liquid-vapor interface governs the dynamics of the interface-bound particles. In particular, the interface displacement contributes to the particle motion toward the droplet apex in a short phase, while the outward advective flow prevails at the late stage of drying and carries the particles to the contact line. The final deposit of the surface-adsorbed particles exhibits a density enhancement at the center, in addition to a coffee ring. Despite its small influence on the final deposit in the present study, the distinct dynamics of surface-active particles due to the interfacial confinement could offer a new route to deposition control when combined with Marangoni effects.

Genetic analysis and association of simple sequence repeat markers with storage root yield, dry matter, starch and β-carotene content in sweetpotato.

PubMed

Yada, Benard; Brown-Guedira, Gina; Alajo, Agnes; Ssemakula, Gorrettie N; Owusu-Mensah, Eric; Carey, Edward E; Mwanga, Robert O M; Yencho, G Craig

2017-03-01

Molecular markers are needed for enhancing the development of elite sweetpotato ( Ipomoea batatas (L.) Lam) cultivars with a wide range of commercially important traits in sub-Saharan Africa. This study was conducted to estimate the heritability and determine trait correlations of storage root yield, dry matter, starch and β-carotene content in a cross between 'New Kawogo' × 'Beauregard'. The study was also conducted to identify simple sequence repeat (SSR) markers associated with these traits. A total of 287 progeny and the parents were evaluated for two seasons at three sites in Uganda and genotyped with 250 SSR markers. Broad sense heritability (H 2 ) for storage root yield, dry matter, starch and β-carotene content were 0.24, 0.68, 0.70 and 0.90, respectively. Storage root β-carotene content was negatively correlated with dry matter (r = -0.59, P < 0.001) and starch (r = -0.93, P < 0.001) content, while storage root yield was positively correlated with dry matter (r = 0.57, P = 0.029) and starch (r = 0.41, P = 0.008) content. Through logistic regression, a total of 12, 4, 6 and 8 SSR markers were associated with storage root yield, dry matter, starch and β-carotene content, respectively. The SSR markers used in this study may be useful for quantitative trait loci analysis and selection for these traits in future.

Genetic analysis and association of simple sequence repeat markers with storage root yield, dry matter, starch and β-carotene content in sweetpotato

PubMed Central

Yada, Benard; Brown-Guedira, Gina; Alajo, Agnes; Ssemakula, Gorrettie N.; Owusu-Mensah, Eric; Carey, Edward E.; Mwanga, Robert O.M.; Yencho, G. Craig

2017-01-01

Molecular markers are needed for enhancing the development of elite sweetpotato (Ipomoea batatas (L.) Lam) cultivars with a wide range of commercially important traits in sub-Saharan Africa. This study was conducted to estimate the heritability and determine trait correlations of storage root yield, dry matter, starch and β-carotene content in a cross between ‘New Kawogo’ × ‘Beauregard’. The study was also conducted to identify simple sequence repeat (SSR) markers associated with these traits. A total of 287 progeny and the parents were evaluated for two seasons at three sites in Uganda and genotyped with 250 SSR markers. Broad sense heritability (H2) for storage root yield, dry matter, starch and β-carotene content were 0.24, 0.68, 0.70 and 0.90, respectively. Storage root β-carotene content was negatively correlated with dry matter (r = −0.59, P < 0.001) and starch (r = −0.93, P < 0.001) content, while storage root yield was positively correlated with dry matter (r = 0.57, P = 0.029) and starch (r = 0.41, P = 0.008) content. Through logistic regression, a total of 12, 4, 6 and 8 SSR markers were associated with storage root yield, dry matter, starch and β-carotene content, respectively. The SSR markers used in this study may be useful for quantitative trait loci analysis and selection for these traits in future. PMID:28588391

Influence of Water Content on Mechanical Properties of Rock in Both Saturation and Drying Processes

NASA Astrophysics Data System (ADS)

Zhou, Zilong; Cai, Xin; Cao, Wenzhuo; Li, Xibing; Xiong, Cheng

2016-08-01

Water content has a pronounced influence on the properties of rock materials, which is responsible for many rock engineering hazards, such as landslides and karst collapse. Meanwhile, water injection is also used for the prevention of some engineering disasters like rock-bursts. To comprehensively investigate the effect of water content on mechanical properties of rocks, laboratory tests were carried out on sandstone specimens with different water contents in both saturation and drying processes. The Nuclear Magnetic Resonance technique was applied to study the water distribution in specimens with variation of water contents. The servo-controlled rock mechanics testing machine and Split Hopkinson Pressure Bar technique were used to conduct both compressive and tensile tests on sandstone specimens with different water contents. From the laboratory tests, reductions of the compressive and tensile strength of sandstone under static and dynamic states in different saturation processes were observed. In the drying process, all of the saturated specimens could basically regain their mechanical properties and recover its strength as in the dry state. However, for partially saturated specimens in the saturation and drying processes, the tensile strength of specimens with the same water content was different, which could be related to different water distributions in specimens.

Curcuma longa L. leaves: Characterization (bioactive and antinutritional compounds) for use in human food in Brazil.

PubMed

Braga, Monick Cristina; Vieira, Ellen Caroline Silvério; de Oliveira, Tatianne Ferreira

2018-11-01

This study evaluated the physicochemical characterization of Curcuma longa L. leaves with respect to proximate composition, mineral content, the presence of antinutritional factors, content of bioactive compounds and antioxidant capacity, and color measurements of leaves in natura and leaves subjected to microwave drying, oven drying, and freeze-drying methods. The proximate composition showed appreciable levels of protein (39.5 g.100 g -1 ), carbohydrates (44.74 g.100 g -1 ), total fiber (34.47 g.100 g -1 ), soluble fiber (22.65 g.100 g -1 ), insoluble fiber (11.81 g.100 g -1 ), ash (13.81 g.100 g -1 ), and low lipid contents (2.47 g.100 g -1 ). No cyanogenic compounds were detected in both samples. Freeze-drying stood out as the method that led to the greatest reductions of the bioactive compounds (33.12-73.86%, dry basis) and antioxidant capacity when compared to the leaves in natura. Microwave drying was the preservation method that produced dry leaves with higher content of bioactive compounds and antioxidant capacity. Therefore, microwave drying produced dehydrated Curcuma longa L. leaves with the highest bioactive compounds and antioxidant activity. Copyright © 2018 Elsevier Ltd. All rights reserved.

Quality factors, antioxidant activity, and sensory properties of jet-tube dried rabbiteye blueberries.

PubMed

Pallas, Laura A; Pegg, Ronald B; Kerr, William L

2013-06-01

Rabbiteye blueberries are an excellent source of nutrients and phytochemicals. They are often dried, which can degrade health-promoting compounds. Means of shortening exposure to high-temperature drying air are desirable. Five cultivars of rabbiteye blueberries ('Premier', 'Tifblue', 'Brightwell', 'Alapaha', and 'Powderblue') were dried in a jet-tube fluidized bed air dryer with varying pretreatments including mechanical abrasion and osmotic dehydration. Drying time ranged from 66 to 95 min at 107 °C, achieving a final water activity of 0.347-0.605. Prior osmotic dehydration significantly reduced the drying time. Vacuum osmotic dehydration for 70 min achieved similar moisture contents to soaking blueberries for 24 h. Jet-tube dried blueberries exhibited greater color saturation than commercially available blueberries. While drying reduced the total monomeric anthocyanin (TMA) content, this occurred to a lesser extent than by other processing methods. The total phenolics content (TPC) and antioxidant capacity (H-ORACFL values) increased after drying. 'Premier' was the most preferred vacuum-infused dried blueberry, with a water activity (aw) of 0.53 and 157 g H2O kg(-1). 'Tifblue' was most preferred amongst the overnight-infused and also unsweetened dried blueberries. Jet-tube drying can substantially reduce drying times while yielding blueberries with good color, sensory properties, TMA, TPC, and H-ORACFL values. Furthermore, some cultivars produce better-quality dried blueberries than others. © 2012 Society of Chemical Industry.

Effects of moisture content or particle size on the in situ degradability of maize silage and alfalfa haylage in lactating dairy cows.

PubMed

Zou, Yang; Dong, Shuangzhao; Du, Yun; Li, Shengli; Wang, Yajing; Cao, Zhijun

2016-09-01

A study using four Holstein cows with ruminal cannulas was conducted to evaluate the degradability of different moisture content or particle size of maize silage and alfalfa haylage. The maize silage (MS; 20-mm length) and alfalfa haylage (AH; 40-mm length) samples were wet (wet maize silage, MSW; wet alfalfa haylage, AHW), dried (dried maize silage, MSD; dried alfalfa haylage, AHD), or ground to pass through a 2.5-mm screen (dried ground maize silage, MSG; dried ground alfalfa haylage, AHG). Samples were incubated in the rumen for 2, 6, 12, 24, 36, 48, and 72 h. Cows were fed ad libitum and allowed free access to water. High moisture content treatment of MSW expressed a lower rinsing NDF and ADF degradability at 2 h ( P  < 0.05) compared with dried samples (MSD and MSG). Different moisture content and particle size had a significant impact ( P  < 0.05) on the NDF degradability at 72 h, ADF degradability at 36, 48, and 72 h, and ruminally degradable ADF. All of the highest values were observed in small particle size and low moisture content AHG treatment. Based on this study, sample processing, such as drying and grinding, should be considered when evaluating nutritive values of forages.

Critical assessment of the performance of electronic moisture analyzers for small amounts of environmental samples and biological reference materials.

PubMed

Krachler, M

2001-12-01

Two electronic moisture analyzers were critically evaluated with regard to their suitability for determining moisture in small amounts (< or = 200 mg) of various environmental matrices such as leaves, needles, soil, peat, sediments, and sewage sludge, as well as various biological reference materials. To this end, several homogeneous bulk materials were prepared which were subsequently employed for the development and optimization of all analytical procedures. The key features of the moisture analyzers included a halogen or ceramic heater and an integrated balance with a resolution of 0.1 mg, which is an essential prerequisite for obtaining precise results. Oven drying of the bulk materials in a conventional oven at 105 degrees C until constant mass served as reference method. A heating temperature of 65degrees C was found to provide accurate and precise results for almost all matrices investigated. To further improve the accuracy and precision, other critical parameters such as handling of sample pans, standby temperature, and measurement delay were optimized. Because of its ponderous heating behavior, the performance of the ceramic radiator was inferior to that of the halogen heater, which produced moisture results comparable to those obtained by oven drying. The developed drying procedures were successfully applied to the fast moisture analysis (1.4-6.3 min) of certified biological reference materials of similar provenance to the investigated the bulk materials. Moisture results for 200 mg aliquots ranged from 1.4 to 7.8% and good agreement was obtained between the recommended drying procedure for the reference materials and the electronic moisture analyzers with absolute uncertainties amounting to 0.1% and 0.2-0.3%, respectively.

[Influence of accessories mixing ratio on sludge biophysical co-drying].

PubMed

Yang, Jin-Long; Du, Qiong; Li, Dong; Han, Rong; Zhao, Yan; Wang, Hong-Tao

2011-08-01

Parameters (temperature, water content and so on) in the process of sludge biophysical co-drying were studied in self-made biophysical co-drying reactor. The sludge: tree bark: recycled sludge was set as 7: 3: 0.5, 9: 3: 0.5, 12: 3: 0.5 respectively. The results suggested that sludge temperature first increased then decreased along with drying time, water content decreased in the first 96 h, then had no obvious variability. While sludge: tree bark: recycled sludge was 9: 3: 0.5, the temperature of sludge spiraling, received to max 67 degrees C at 48 h under three different accessories mixture ratio, and was kept for 72 h above 55 degrees C, then spiraling, the final water content of sludge decreased from 74.1% to 61.8%, received the optimal water content removing rate 43.5%. Accessories mixing ratio had important influence on the process of sludge biophysical co-drying, sludge with proper mixing ratio can modify the structure of sludge, improve sludge permeability, arouse and keep microorganic activity, which will enhance sludge temperature and strengthen water content removal rate.

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2011 CFR

2011-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2012 CFR

2012-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2013 CFR

2013-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

21 CFR 184.1979c - Whey protein concentrate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... “Dried Milk, Nonfat Dry Milk, and Malted Milk.” (iv) Lactose content, maximum 60 percent—as determined by... Action” under the heading “Lactose,” or in section 31.061 (dry sample), entitled “Lane-Eynon General Volumetric Method” under the heading “Lactose—Chemical Methods—Official Final Action.” (v) Moisture content...

21 CFR 184.1979c - Whey protein concentrate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... “Dried Milk, Nonfat Dry Milk, and Malted Milk.” (iv) Lactose content, maximum 60 percent—as determined by... Action” under the heading “Lactose,” or in section 31.061 (dry sample), entitled “Lane-Eynon General Volumetric Method” under the heading “Lactose—Chemical Methods—Official Final Action.” (v) Moisture content...

Adaptation of the AOAC 2011.25 integrated total dietary fiber assay to determine the dietary fiber and oligosaccharide content of dry edible beans.

PubMed

Kleintop, Adrienne E; Echeverria, Dimas; Brick, Leslie A; Thompson, Henry J; Brick, Mark A

2013-10-09

Dietary fiber (DF) has important health benefits in the human diet. Developing dry edible bean (Phaseolus vulgaris L.) cultivars with improved DF and reduced nondigestible oligosaccharide content is an important goal for dry bean breeders to increase consumer acceptance. To determine if genetic variation exists among dry bean cultivars for DF, two populations of diverse dry bean cultivars/lines that represent two centers of dry bean domestication were evaluated for dietary fiber using the Integrated Total Dietary Fiber Assay (AOAC 2011.25). This assay was adapted to measure water insoluble dietary fiber, water soluble dietary fiber, oligosaccharides raffinose and stachyose, and the calculated total dietary fiber (TDF) content of cooked dry bean seed. The AOAC 2011.25 protocol was modified by using a quick, simple, and sensitive high-performance liquid chromatography method paired with an electrochemical detection method to separate and quantify specific oligosaccharides, and using duplicate samples as replicates to generate statistical information. The TDF of dry bean entries ranged from 20.0 to 27.0% in population I and from 20.6 to 25.7% in population II. Total oligosaccharides ranged from 2.56 to 4.65% in population I and from 2.36 to 3.84% in population II. The results suggest that significant genetic variation exists among dry bean cultivars/lines to allow for genetic selection for improved DF content in dry beans and that the modifications to the AOAC 2011.25 method were suitable for estimating DF in cooked dry edible beans.

Chinese medicinal herbal residues as a bulking agent for food waste composting.

PubMed

Zhou, Ying; Selvam, Ammaiyappan; Wong, Jonathan W C

2018-02-01

This study aimed to co-compost Chinese medicinal herbal residues (CMHRs) as the bulking agent with food waste (FW) to develop a high value antipathogenic compost. The FW, sawdust (SD) and CMHRs were mixed at three different mixing ratios, 5:5:1, 2:2:1 and 1:1:1 on dry weight basis. Lime at 2.25% was added to the composting mix to buffer the pH during the composting. A control without lime addition was also included. The mixtures were composted in 20-L in-vessel composters for 56 days. A maximum of 67.2% organic decomposition was achieved with 1:1:1 mixing ratio within 8 weeks. The seed germination index was 157.2% in 1:1:1 mixing ratio, while other ratios showed <130.0% and the treatment without lime showed 40.3%. Therefore use of CMHRs as the bulking agent to compost food waste at the dry weight ratio of 1:1:1 (FW: SD: CMHRs) was recommended for FW-CMHRs composting. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Effects of ex situ rice straw incorporation on organic matter content and main physical properties of hilly red soil].

PubMed

Zhu, Han-hua; Huang, Dao-you; Liu, Shou-long; Zhu, Qi-hong

2007-11-01

Two typical land-use types, i.e., newly cultivated slope land and mellow upland, were selected to investigate the effects of ex situ rice straw incorporation on the organic matter content, field water-holding capacity, bulk density, and porosity of hilly red soil, and to approach the correlations between these parameters. The results showed that ex situ incorporation of rice straw increased soil organic matter content, ameliorated soil physical properties, and improved soil water storage. Comparing with non-fertilization and applying chemical fertilizers, ex situ incorporation of rice straw increased the contents of organic matter (5.8%-28.9%) and > 0.25 mm water-stable aggregates in 0-20 cm soil layer, and increased the field water-holding capacity (6.8%-16.2%) and porosity (4.8%-7.7%) significantly (P < 0.05) while decreased the bulk density (4.5%-7.5%) in 10-15 cm soil layer. The organic matter content in 0-20 cm soil layer was significantly correlated to the bulk density, porosity, and field water-holding capacity in 10-15 cm soil layer (P < 0.01), and the field water-holding capacity in 0-20 cm and 10-15 cm soil layers was significantly correlated to the bulk density and porosity in these two layers (P < 0.05).

Laboratory microwave measurement of the moisture content in seed cotton and ginned cotton fiber

USDA-ARS?s Scientific Manuscript database

The timely and accurate measurement of cotton fiber moisture content is important, but the measurement is often performed by laborious, time-consuming laboratory oven drying methods. Microwave technology for measuring fiber moisture content directly (not for drying only) offers potential advantages...

Late Holocene environmental changes recorded in the sediments of Lago Thompson, Northern Chilean Patagonia

NASA Astrophysics Data System (ADS)

Fagel, Nathalie; Nuttin, Laurence; Bertrand, Sébastien; Borgniet, Geoffrey; Schmidt, Sabine; Araneda, Alberto; Torrejon, Fernando; Urrutia, Roberto

2010-05-01

We investigate the sedimentary record of Lago Thompson, a small lake (area 1.1 km2, watershed ~8 km2) located at an elevation of 750 masl in Northern Chilean Patagonia (45.38 °S, 71.47°W). At Present, the climate conditions around the lake are relatively dry, with annual precipitation averaging 500 mm. The goal of this study is to evaluate the natural climate variability over the Last Millennium in Northern Chilean Patagonia and its impact on the environment. The coring site was selected after a bathymetric survey using an echo-sounder. Several short cores were retrieved in 2008 using an Uwitec gravity corer: the length of the cores ranges between 124 and 132 cm. The preliminary age model is based on 4 AMS radiocarbon ages measured on bulk sediment and organic macro-remains. The radiocarbon ages demonstrate that the sediment cores cover the last 850 to 950 years. This sediment record, which is characterized by accumulation rates ranging between 1 and 3 mm/yr, can therefore be studied at decennial to centennial resolution. To reconstruct past changes in climate and the environment, we conducted a multiproxy study combining sedimentological, mineralogical and geochemical analyses (LOI 105, 550 and 950°C, biogenic silica content, magnetic susceptibility, tephrostratigraphy, bulk organic geochemistry, bulk mineralogy by X-ray diffraction, and inorganic geochemistry by ITRAX core scanner and ICP-AES). Visual descriptions and X-ray radiographies demonstrate that the sediment record is relatively undisturbed. The sediment is composed of light brown organic-rich clayey material. The lower part of the core (below 75 cm) is finely laminated whereas the upper part is more homogeneous. Magnetic susceptibility values highlight two tephra layers that represent explosive eruptions of volcanoes from the southern volcanic zone of Chile (Hudson, Cay, or Macá volcanoes). The biogenic silica content of the sediment retrieved in Lago Thompson is high (40 to 80%), and probably related to the small catchment to lake surface ratio, which limits the supply of terrestrial particles to the lake. The inorganic content of the sediment is very low. Some clay minerals, quartz and feldspars were identified by X-ray diffraction. This observation is in agreement with the low C/N ratio (~ 8-9) of the bulk organic matter, providing evidence that most of the organic particles originate from aquatic productivity. The high organic matter content (mean 15%, concentrations reaching up to 20%) and its low C/N ratio provide evidence that the lake productivity remained high over the last 900 years. Higher concentrations in biogenic silica and organic matter between 1550 and 1800 AD could be interpreted as drier climate conditions in the Andes of Northern Patagonia during the Little Ice Age. Further research will focus on biological proxies (diatom, chironomid, pollen) to improve this interpretation. This research is funded by Chilean and Belgian projects (Fondecyt project number 1070508, and FNRS "crédits au chercheur" 1360 2007-2010, respectively).

Effects of hot air and freeze drying methods on antioxidant activity, colour and some nutritional characteristics of strawberry tree (Arbutus unedo L) fruit.

PubMed

Orak, H H; Aktas, T; Yagar, H; İsbilir, S Selen; Ekinci, N; Sahin, F Hasturk

2012-08-01

Antioxidant activity, colour and some nutritional properties of hot air and freeze-dried strawberry tree (Arbutus unedo L.) fruits were investigated. Additionally, the effects of two pre-treatments, namely ethyl oleate and water blanching, were compared in terms of drying characteristics. For determination of antioxidant activities in ethanol extracts, two different analytical methods were used: 1,1-diphenyl-2-picrylhydrazyl scavenging activity and β-carotene bleaching activity. As a result, the ethyl oleate pre-treatment shortened the drying time by hot air method and gave a higher 1,1-diphenyl-2-picrylhydrazyl scavenging activity (82.16 ± 0.34%), total phenolic content (7.62 ± 1.09 µg GAE/g extract), ascorbic acid content (236.93 ± 20.14 mg/100 g), besides hydromethylfurfural was not observed. Freeze-dried fruits exhibited higher ascorbic acid content (368.63 ± 17.16 mg/100 g) than those fresh fruits (231.33 ± 19.51 mg/100 g) and nearly 1,1-diphenyl-2-picrylhydrazyl activity (93.52 ± 0.41 %) to fresh fruits (94.03 ± 1.18%). Colour characteristics, sugar content and mineral contents of fruits were significantly affected by pre-treatments and drying methods (p < 0.05). It is concluded that the drying of strawberry tree fruits should bring a valuable and attractive foodstuff to food industry due to the rich nutritional components, antioxidant activity and colour. Another conclusion from this study is that the freeze-drying is the best drying method to keep the nutritional value, antioxidant activity and sensory properties of fruits.

Improved texture measurement during deformation of polycrystalline olivine at high pressure

NASA Astrophysics Data System (ADS)

Dixon, N. A.; Durham, W. B.; Kohlstedt, D. L.; Hunt, S. A.

2014-12-01

Unresolved issues in geodynamics demand a better understanding of the bulk mechanical properties of mantle minerals, and also careful analysis of the complex lattice-scale physics behind these properties. Instead of probing the mechanical properties of a material by testing the relationship between "bulk" stress and strain rate in a sample at a variety of conditions (varying P, T, water content, and other environmental variables), synchrotron x-ray diffraction now allows us to observe, in situ, the active deformation physics in much greater detail. This includes in situ monitoring of plastic anisotropy and local stress heterogeneity, grain size, the development of lattice-preferred orientation (LPO), and even the partitioning of stress between multiple phases in the same polycrystalline sample. Here, we present results obtained with the use of the MTEX toolbox for Matlab and energy-dispersive x-ray diffraction, showing the in situ development of LPO in deforming dry San Carlos olivine samples, at pressures from 2-7 GPa. These measurements hint at the active dislocation mechanisms for these conditions. The ability generate a broad range of mantle conditions in the D-DIA, while precisely measuring the structure and conditions within our sample at the grain and lattice scale, demonstrates the promising future of deformation experiments as a means to understanding the evolution of the deep Earth.

Simulation of the process kinetics and analysis of physicochemical properties in the freeze drying of kale

NASA Astrophysics Data System (ADS)

Dziki, Dariusz; Polak, Renata; Rudy, Stanisław; Krzykowski, Andrzej; Gawlik-Dziki, Urszula; Różyło, Renata; Miś, Antoni; Combrzyński, Maciej

2018-01-01

Investigations were performed to study the freeze-drying process of kale (Brassica oleracea L. var acephala). The process of freeze-drying was performed at temperatures of 20, 40, and 60°C for whole pieces of leaves and for pulped leaves. The kinetics of the freeze-drying of both kale leaves and kale pulp were best described by the Page model. The increasing freeze-drying temperature from 20 to 60°C induced an approximately two-fold decrease in the drying time. Freeze-drying significantly increased the value of the lightness, delta Chroma, and browning index of kale, and had little influence on the hue angle. The highest increase in the lightness and delta Chroma was observed for whole leaves freeze-dried at 20°C. An increase in the drying temperature brought about a slight decrease in the lightness, delta Chroma and the total colour difference. Pulping decreased the lightness and hue angle, and increased browning index. Freeze-drying engendered a slight decrease in the total phenolics content and antioxidant activity, in comparison to fresh leaves. The temperature of the process and pulping had little influence on the total phenolics content and antioxidant activity of dried kale, but significantly decreased the contents of chlorophyll a and chlorophyll b.

Effects of Chamber Pressure and Partial Pressure of Water Vapor on Secondary Drying in Lyophilization.

PubMed

Searles, James A; Aravapalli, Sridhar; Hodge, Cody

2017-10-01

Secondary drying is the final step of lyophilization before stoppering, during which water is desorbed from the product to yield the final moisture content. We studied how chamber pressure and partial pressure of water vapor during this step affected the time course of water content of aqueous solutions of polyvinylpyrrolidone (PVP) in glass vials. The total chamber pressure had no effect when the partial pressure of water vapor was very low. However, when the vapor phase contained a substantial fraction of water vapor, the PVP moisture content was much higher. We carried out dynamic vapor sorption experiments (DVS) to demonstrate that the higher PVP moisture content was a straightforward result of the higher water vapor content in the lyophilizer. The results highlight that the partial pressure of water vapor is extremely important during secondary drying in lyophilization, and that lower chamber pressure set points for secondary drying may sometimes be justified as a strategy for ensuring low partial pressure of water vapor, especially for lyophilizers that do not inject dry gas to control pressure. These findings have direct application for process transfers/scale ups from freeze-dryers that do not inject dry gas for pressure control to those that do, and vice versa.

Studies on convective drying of `Ameclyae' Opuntia ficus-indica seeds and its effect on the quality of extracted oil based on its α-tocopherol content

NASA Astrophysics Data System (ADS)

Hassini, Lamine; Bettaieb, Emna; Motri, Samia; Desmorieux, Hélène

2018-02-01

The aim of this work is to model the thin layer convective drying kinetics of `Ameclyae' prickly pear seed variety and to evaluate the effects of drying conditions on the quality of extracted seed oil, specifically α-tocopherol content. Drying experiments were carried on following a full 23 factorial design using a vertical drying tunnel. The study is restricted to a particular particle size and a particular seed bed of height 0.5 cm, of effective porosity around 0.4 and of initial moisture content on dry basis equal to 1.2 (± 0.01) kg/kg. The temperature range was 45 to 70 °C, relative humidity range was 15-30% and air velocity was 1 and 2 m/s. The experimental drying curves were fitted to different semi-theoretical drying models proposed in the literature. The Midilli-Kucuk model was found with satisfaction describing the seed air drying curves with a correlation coefficient of 0.999 and a standard error of 0.01. For each drying condition, the extraction of fixed oil seeds was performed at cold using liquid/solid separation method. The oil quality was evaluated on the basis of the α-tocopherol content. The α-tocopherol was identified and quantified by high-performance liquid chromatography (HPLC-UV). According to the experimental results, it was found that drying air velocity is the most important factor influencing the concentration of α-tocopherol, whereas the effects of temperature and relative humidity were lower. The increase of the velocity from 1 m/s to 2 m/s reduced the α-tocopherol concentration by about 25%. The convective drying of thin layer of seeds at soft air conditions, drying temperature of 45 °C, relative humidity of 15% and air velocity of 1 m/s give the optimal quality of extracted oil in terms of α-tocopherol content. Characterization of the morphologic structure of seeds was also performed by SEM.

Comparison of drying characteristic and uniformity of banana cubes dried by pulse-spouted microwave vacuum drying, freeze drying and microwave freeze drying.

PubMed

Jiang, Hao; Zhang, Min; Mujumdar, Arun S; Lim, Rui-Xin

2014-07-01

To overcome the flaws of high energy consumption of freeze drying (FD) and the non-uniform drying of microwave freeze drying (MFD), pulse-spouted microwave vacuum drying (PSMVD) was developed. The results showed that the drying time can be dramatically shortened if microwave was used as the heating source. In this experiment, both MFD and PSMVD could shorten drying time by 50% as compared to the FD process. Depending on the heating method, MFD and PSMVD dried banana cubes showed trends of expansion while FD dried samples demonstrated trends of shrinkage. Shrinkage also brought intensive structure and highest fracturability of all three samples dried by different methods. The residual ascorbic acid content of PSMVD dried samples can be as high as in FD dried samples, which were superior to MFD dried samples. The tests confirmed that PSMVD could bring about better drying uniformity than MFD. Besides, compared with traditional MFD, PSMVD can provide better extrinsic feature, and can bring about improved nutritional features because of the higher residual ascorbic acid content. © 2013 Society of Chemical Industry.

Physicochemical properties of whole fruit plum powders obtained using different drying technologies.

PubMed

Michalska, Anna; Wojdyło, Aneta; Lech, Krzysztof; Łysiak, Grzegorz P; Figiel, Adam

2016-09-15

Physicochemical quality parameters of plum powders obtained by applying conventional drying methods and their combination devised to process plums were evaluated. The effect of freeze-drying (FD), vacuum drying (VD), convective drying (CD), microwave-vacuum drying (MVD) and combination of convective pre-drying and microwave finish-drying (CPD-MVFD) affected physical (bulk density, porosity, colour, solubility) and chemical (polyphenolic compounds determined by UPLC and antioxidant capacity by TEAC ABTS and FRAP methods) properties of plum powders. The MVD at 1.2 W g(-1) and a novel combination for plum powders production - CPD-MVFD at 70 °C/1.2 W g(-1) allowed the best preservation of phenolic compounds and increased the efficiency of production. Results obtained support the use of MVD and its combination for better quality of dried plum products. The study proved that the determination of the browning index and HMF level (formed via Maillard reaction) might be good tool for monitoring the thermal processing of plum powders. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dynamics of Photoexcitation and Photocatalysis at Nanostructured Carbon Interfaces

DTIC Science & Technology

2015-07-14

nanotubes with a sacrificial polymer and eliminating the polymer using a critical point drying process. This process creates aerogel structures that...Bindl DJ, Jacobberger RM, Wu M-Y, Singha Roy S, Arnold MS, Semiconducting Carbon Nanotube Aerogel Bulk Heterojunction Solar Cells, Small 10 (16), pp...ACS Nano 2015, 9 (1), 564-572. Ye Y, Bindl DJ, Jacobberger RM, Wu M-Y, Singha Roy S, Arnold MS, Semiconducting Carbon Nanotube Aerogel Bulk

In-line moisture monitoring in fluidized bed granulation using a novel multi-resonance microwave sensor.

PubMed

Peters, Johanna; Bartscher, Kathrin; Döscher, Claas; Taute, Wolfgang; Höft, Michael; Knöchel, Reinhard; Breitkreutz, Jörg

2017-08-01

Microwave resonance technology (MRT) is known as a process analytical technology (PAT) tool for moisture measurements in fluid-bed granulation. It offers a great potential for wet granulation processes even where the suitability of near-infrared (NIR) spectroscopy is limited, e.g. colored granules, large variations in bulk density. However, previous sensor systems operating around a single resonance frequency showed limitations above approx. 7.5% granule moisture. This paper describes the application of a novel sensor working with four resonance frequencies. In-line data of all four resonance frequencies were collected and further processed. Based on calculation of density-independent microwave moisture values multiple linear regression (MLR) models using Karl-Fischer titration (KF) as well as loss on drying (LOD) as reference methods were build. Rapid, reliable in-process moisture control (RMSEP≤0.5%) even at higher moisture contents was achieved. Copyright © 2017 Elsevier B.V. All rights reserved.

Bioaccumulation of elements in three selected mushroom species from southwest Poland.

PubMed

Mleczek, Mirosław; Siwulski, Marek; Mikołajczak, Patrycja; Goliński, Piotr; Gąsecka, Monika; Sobieralski, Krzysztof; Dawidowicz, Luiza; Szymańczyk, Mateusz

2015-01-01

The contents of 16 minerals and trace elements (Ag, As, Ca, Cd, Co, Cr, Cu, Fe, Hg, Mg, Mn, Ni, Pb, Pt, Ti and Zn) were analyzed in edible mushrooms (Leccinum scabrum, Boletus edulis and Boletus badius) collected in southwest Poland. Content of Co, Ni and Pb was similar in all tested mushroom species, while content of Ag, Ca, Cd, Hg and Ti was significantly higher in B. edulis than in L. scabrum and B. badius. The largest differences between these species were observed for Fe and Zn accumulation. The highest contents of these elements were noted in B. badius bodies (202 ± 88 and 137 ± 24 mg kg(-1) dry matter, respectively), lower in B. edulis (131 ± 99 and 89 ± 26 mg kg(-1) dry matter, respectively) and lowest in L. scabrum. Differences in As, Cu and Cr content between tested species were observed mainly between L. scabrum and B. badius fruiting bodies. Content of Pt was below 0.01 mg kg(-1) dry matter). In the case of Mg and Mn accumulation, differences between B. edulis and B. badius were not observed (478 and 440 mg kg(-1) dry matter for Mg and 23 and 19 mg kg(-1) dry matter for Mn), and the results showed significantly higher content of these elements than in L. scabrum bodies (312 and 10 mg kg(-1) dry matter, respectively). It is worth underlining that clear accumulation shown by the bioconcentration factor (BCF>1) observed for all three mushroom species was noted in the case of elements Ag, Cd, Co, Cu, Hg, Ni and Zn only.

Effect of ethanol, dry extract and reducing sugars on density and viscosity of Brazilian red wines.

PubMed

Neto, Flávia S P P; de Castilhos, Maurício B M; Telis, Vânia R N; Telis-Romero, Javier

2015-05-01

Density and viscosity are properties that exert great influence on the body of wines. The present work aimed to evaluate the influence of the alcoholic content, dry extract, and reducing sugar content on density and viscosity of commercial dry red wines at different temperatures. The rheological assays were carried out on a controlled stress rheometer, using concentric cylinder geometry at seven temperatures (2, 8, 14, 16, 18, 20 and 26 °C). Wine viscosity decreased with increasing temperature and density was directly related to the wine alcohol content, whereas viscosity was closely linked to the dry extract. Reducing sugars did not influence viscosity or density. Wines produced from Italian grapes were presented as full-bodied with higher values for density and viscosity, which was linked to the higher alcohol content and dry extract, respectively. The results highlighted the major effects of certain physicochemical properties on the physical properties of wines, which in turn is important for guiding sensory assessments. © 2014 Society of Chemical Industry.

Design and operation of a solarheated dry kiln for tropical latitudes

Treesearch

Brian Bond; Omar Espinoza; Philip Araman

2011-01-01

Lumber is usually dried to a specific moisture content prior to further manufacturing or use. While lumber can be air-dried, the ambient humidity in most localities prevents the lumber from reaching the moisture content necessary for dimensional stability and use, especially for interior use. Solar kilns are an inexpensive alternative to conventional steam-heated kilns...

House log drying rates in southeast Alaska for covered and uncovered softwood logs

Treesearch

David Nicholls; Allen Brackley

2009-01-01

Log moisture content has an important impact on many aspects of log home construction, including log processing, transportation costs, and dimensional stability in use. Air-drying times for house logs from freshly harvested trees can depend on numerous factors including initial moisture content, log diameter, bark condition, and environmental conditions during drying....

Impingement drying for preparing dried apple pomace flour and its fortification in bakery and meat products.

PubMed

Jung, Jooyeoun; Cavender, George; Zhao, Yanyun

2015-09-01

This study aimed to evaluate impingement drying (ID) as a rapid drying method to dry wet apple pomace (WAP) and to investigate the fortification of dried apple pomace flour (APF) or WAP in bakery and meat products. ID at ~110 °C reduced the moisture content of apple pomace from 80 % (wet basis) to 4.5 % within 3 h, compared with 24 h to 2.2 % using 40 °C forced-air drying and ~60 h to 2.3 % using freeze drying. Furthermore, ID enhanced the extractable phenolic compounds, allowing for a 58 % increase in total phenolic content (TPC) compared with wet pomace, a 110 % and 83 % higher than TPC in forced-air dried and freeze dried samples, respectively. The 15-20 % APF-fortified cookies were found to be ~44-59 % softer, ~30 % more chewy, and ~14 % moister than those of the control. WAP-fortified meat products had significantly higher dietary fiber content (0.7-1.8 % vs. 0.1-0.2 % in control) and radical scavenging activity than that of the control. These results suggest that impingement drying is a fast and effective method for preparing dried APF with highly retained bioactive compounds, and apple pomace fortified products maintained or even had improved quality.

Suitability of microwave drying for mealworms (Tenebrio molitor) as alternative to freeze drying: Impact on nutritional quality and colour.

PubMed

Lenaerts, S; Van Der Borght, M; Callens, A; Van Campenhout, L

2018-07-15

Freeze drying represents the current practice to stabilize mealworms, even though it is an energy demanding technique. Therefore, it was examined in the present study whether microwave drying could be a proper alternative. To this end, the impact of both drying techniques on the proximate composition, vitamin B 12 content, fatty acid profile, oxidation status and colour parameters of mealworms was investigated. Furthermore, the influence of the application of vacuum during microwave drying was studied. The different drying technologies resulted in small differences in the proximate composition, while the vitamin B 12 content was only reduced by microwave drying. The fat fraction of freeze dried mealworms showed a higher oxidation status than the fat of microwave dried mealworms. Application of a vacuum during the microwave drying process did not appear to offer advantages. This research shows that for mealworms microwave drying can be a proper alternative to freeze drying. Copyright © 2018 Elsevier Ltd. All rights reserved.

Megaregolith insulation, internal temperatures, and bulk uranium content of the moon

NASA Technical Reports Server (NTRS)

Warren, Paul H.; Rasmussen, Kaare L.

1986-01-01

Finite-difference models are used to study the effects of insulation by the megaregolith on lunar thermal evolution. Results indicate that the megaregolith has two important influences on heat flow: (1) Because the megaregolith is exceptionally thin in mare regions, heat passes more readily through them than through highland regions, and even flows laterally from the highland toward the mare. As a result, heat flow is exceptionally high along a boundary between highland and mare regions. (2) On a global scale, megaregolith insulation combined with lithosphere insulation causes slow cooling, which as a cumulative effect results in high present-day mantle temperatures and heat flow. Assuming that the global mean megaregolith thickness is 2 km, a heat flow of 12 mW/sq m is best matched by models with bulk moon U contents of 20-21 ng/g. Independent constraints on lunar internal temperatures derived from magnetic and tectonic data are best matched by models with about 14 ng/g U. Thus the bulk moon U content is roughly 17 ng/g. These results imply that the bulk moon contents of U, and related refractory lithophile elements such as Th, Al, Ca, etc., must be considerably lower than commonly assumed.

Haptoglobin and serum amyloid A in bulk tank milk in relation to raw milk quality.

PubMed

Akerstedt, Maria; Waller, Karin Persson; Sternesjö, Ase

2009-11-01

The aim of the present study was to evaluate relationships between the presence of the two major bovine acute phase proteins haptoglobin (Hp) and serum amyloid A (SAA) and raw milk quality parameters in bulk tank milk samples. Hp and SAA have been suggested as specific markers of mastitis but recently also as markers for raw milk quality. Since mastitis has detrimental effects on milk quality, it is important to investigate whether the presence of Hp or SAA indicates such changes in the composition and properties of the milk. Bulk tank milk samples (n=91) were analysed for Hp, SAA, total protein, casein, whey protein, proteolysis, fat, lactose, somatic cell count and coagulating properties. Samples with detectable levels of Hp had lower casein content, casein number and lactose content, but higher proteolysis than samples without Hp. Samples with detectable levels of SAA had lower casein number and lactose content, but higher whey protein content than samples without SAA. The presence of acute phase proteins in bulk tank milk is suggested as an indicator for unfavourable changes in the milk composition, e.g. protein quality, due to udder health disturbances, with economical implications for the dairy industry.

Effects of chemical composite, puffing temperature and intermediate moisture content on physical properties of potato and apple slices

NASA Astrophysics Data System (ADS)

Tabtaing, S.; Paengkanya, S.; Tanthong, P.

2017-09-01

Puffing technique is the process that can improve texture and volumetric of crisp fruit and vegetable. However, the effect of chemical composite in foods on puffing characteristics is still lack of study. Therefore, potato and apple slices were comparative study on their physical properties. Potato and apple were sliced into 2.5 mm thickness and 2.5 cm in diameter. Potato slices were treated by hot water for 2 min while apple slices were not treatment. After that, they were dried in 3 steps. First step, they were dried by hot air at temperature of 90°C until their moisture content reached to 30, 40, and 50 % dry basis. Then they were puffed by hot air at temperature of 130, 150, and 170°C for 2 min. Finally, they were dried again by hot air at temperature of 90°C until their final moisture content reached to 4% dry basis. The experimental results showed that chemical composite of food affected on physical properties of puffed product. Puffed potato had higher volume ratio than those puffed apple because potato slices contains starch. The higher starch content provided more hard texture of potato than those apples. Puffing temperature and moisture content strongly affected on the color, volume ratio, and textural properties of puffed potato slices. In addition, the high drying rate of puffed product observed at high puffing temperature and higher moisture content.

Relationship between moisture content and electrical impedance of carrot slices during drying

NASA Astrophysics Data System (ADS)

Kertész, Ákos; Hlaváčová, Zuzana; Vozáry, Eszter; Staroňová, Lenka

2015-01-01

Electrical properties of food materials can give information about the inner structure and physiological state of biological tissues. Generally, the process of drying of fruits and vegetables is followed by weight loss. The aim of this study was to measure the impedance spectra of carrot slices during drying and to correlate impedance parameters to moisture content in different drying periods. Cylindrical slices were cut out from the carrot root along the axis. The slices were dried in a Venticell 111 air oven at 50°C. The weight of the slices was measured with a Denver SI-603 electronic analytical and precision balance. The weighing of the samples was performed every 30 min at the beginning of drying and every 60 min after the process. The moisture content of the samples was calculated on wet basis. The magnitude and phase angle of electrical impedance of the slices were measured with HP 4284A and 4285A precision LCR meters in the frequency range from 30 Hz to 1 MHz and from 75 kHz to 30 MHz, respectively, at voltage 1 V. The impedance measurement was performed after weighting. The change in the magnitude of impedance during drying showed a good correlation with the change in the moisture content.

Mathematical modelling for the drying method and smoothing drying rate using cubic spline for seaweed Kappaphycus Striatum variety Durian in a solar dryer

NASA Astrophysics Data System (ADS)

M Ali, M. K.; Ruslan, M. H.; Muthuvalu, M. S.; Wong, J.; Sulaiman, J.; Yasir, S. Md.

2014-06-01

The solar drying experiment of seaweed using Green V-Roof Hybrid Solar Drier (GVRHSD) was conducted in Semporna, Sabah under the metrological condition in Malaysia. Drying of sample seaweed in GVRHSD reduced the moisture content from about 93.4% to 8.2% in 4 days at average solar radiation of about 600W/m2 and mass flow rate about 0.5 kg/s. Generally the plots of drying rate need more smoothing compared moisture content data. Special cares is needed at low drying rates and moisture contents. It is shown the cubic spline (CS) have been found to be effective for moisture-time curves. The idea of this method consists of an approximation of data by a CS regression having first and second derivatives. The analytical differentiation of the spline regression permits the determination of instantaneous rate. The method of minimization of the functional of average risk was used successfully to solve the problem. This method permits to obtain the instantaneous rate to be obtained directly from the experimental data. The drying kinetics was fitted with six published exponential thin layer drying models. The models were fitted using the coefficient of determination (R2), and root mean square error (RMSE). The modeling of models using raw data tested with the possible of exponential drying method. The result showed that the model from Two Term was found to be the best models describe the drying behavior. Besides that, the drying rate smoothed using CS shows to be effective method for moisture-time curves good estimators as well as for the missing moisture content data of seaweed Kappaphycus Striatum Variety Durian in Solar Dryer under the condition tested.

Mathematical modelling for the drying method and smoothing drying rate using cubic spline for seaweed Kappaphycus Striatum variety Durian in a solar dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

M Ali, M. K., E-mail: majidkhankhan@ymail.com, E-mail: eutoco@gmail.com; Ruslan, M. H., E-mail: majidkhankhan@ymail.com, E-mail: eutoco@gmail.com; Muthuvalu, M. S., E-mail: sudaram-@yahoo.com, E-mail: jumat@ums.edu.my

2014-06-19

The solar drying experiment of seaweed using Green V-Roof Hybrid Solar Drier (GVRHSD) was conducted in Semporna, Sabah under the metrological condition in Malaysia. Drying of sample seaweed in GVRHSD reduced the moisture content from about 93.4% to 8.2% in 4 days at average solar radiation of about 600W/m{sup 2} and mass flow rate about 0.5 kg/s. Generally the plots of drying rate need more smoothing compared moisture content data. Special cares is needed at low drying rates and moisture contents. It is shown the cubic spline (CS) have been found to be effective for moisture-time curves. The idea ofmore » this method consists of an approximation of data by a CS regression having first and second derivatives. The analytical differentiation of the spline regression permits the determination of instantaneous rate. The method of minimization of the functional of average risk was used successfully to solve the problem. This method permits to obtain the instantaneous rate to be obtained directly from the experimental data. The drying kinetics was fitted with six published exponential thin layer drying models. The models were fitted using the coefficient of determination (R{sup 2}), and root mean square error (RMSE). The modeling of models using raw data tested with the possible of exponential drying method. The result showed that the model from Two Term was found to be the best models describe the drying behavior. Besides that, the drying rate smoothed using CS shows to be effective method for moisture-time curves good estimators as well as for the missing moisture content data of seaweed Kappaphycus Striatum Variety Durian in Solar Dryer under the condition tested.« less

Soil permittivity response to bulk electrical conductivity for selected soil water sensors

USDA-ARS?s Scientific Manuscript database

Bulk electrical conductivity can dominate the low frequency dielectric loss spectrum in soils, masking changes in the real permittivity and causing errors in estimated water content. We examined the dependence of measured apparent permittivity (Ka) on bulk electrical conductivity in contrasting soil...

[Optimization of vacuum belt drying process of Gardeniae Fructus in Reduning injection by Box-Behnken design-response surface methodology].

PubMed

Huang, Dao-sheng; Shi, Wei; Han, Lei; Sun, Ke; Chen, Guang-bo; Wu Jian-xiong; Xu, Gui-hong; Bi, Yu-an; Wang, Zhen-zhong; Xiao, Wei

2015-06-01

To optimize the belt drying process conditions optimization of Gardeniae Fructus extract from Reduning injection by Box-Behnken design-response surface methodology, on the basis of single factor experiment, a three-factor and three-level Box-Behnken experimental design was employed to optimize the drying technology of Gardeniae Fructus extract from Reduning injection. With drying temperature, drying time, feeding speed as independent variables and the content of geniposide as dependent variable, the experimental data were fitted to a second order polynomial equation, establishing the mathematical relationship between the content of geniposide and respective variables. With the experimental data analyzed by Design-Expert 8. 0. 6, the optimal drying parameter was as follows: the drying temperature was 98.5 degrees C , the drying time was 89 min, the feeding speed was 99.8 r x min(-1). Three verification experiments were taked under this technology and the measured average content of geniposide was 564. 108 mg x g(-1), which was close to the model prediction: 563. 307 mg x g(-1). According to the verification test, the Gardeniae Fructus belt drying process is steady and feasible. So single factor experiments combined with response surface method (RSM) could be used to optimize the drying technology of Reduning injection Gardenia extract.

Quality evaluation of onion bulbs during low temperature drying

NASA Astrophysics Data System (ADS)

Djaeni, M.; Asiah, N.; Wibowo, Y. P.; Yusron, D. A. A.

2016-06-01

A drying technology must be designed carefully by evaluating the foods' final quality properties as a dried material. Thermal processing should be operated with the minimum chance of substantial flavour, taste, color and nutrient loss. The main objective of this research was to evaluate the quality parameters of quercetin content, color, non-enzymatic browning and antioxidant activity. The experiments showed that heating at different temperatures for several drying times resulted in a percentage of quercetin being generally constant. The quercetin content maintained at the value of ±1.2 % (dry basis). The color of onion bulbs was measured by CIE standard illuminant C. The red color (a*) of the outer layer of onion bulbs changed significantly when the drying temperature was increased. However the value of L* and b* changed in a fluctuating way based on the temperature. The change of onion colors was influenced by temperature and moisture content during the drying process. The higher the temperature, the higher it affects the rate of non-enzymatic browning reaction. The correlation between temperature and reaction rate constant was described as Arrhenius equation. The rate of non-enzymatic browning increases along with the increase of drying temperature. The results showed that higher drying temperatures were followed by a lower IC10. This condition indicated the increase of antioxidant activity after the drying process.

46 CFR 154.1155 - Hand hose line: Coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Firefighting System: Dry Chemical § 154.1155 Hand hose line: Coverage. The coverage for the area for a hand...

7 CFR 52.3185 - Moisture limits.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Method or in accordance with methods that give equivalent results. The moisture limits in Table IV apply only to so-called “bulk packs” of dried prunes packaged in non-hermetically sealed containers holding...

[Freeze drying process optimization of ginger juice-adjuvant for Chinese materia medica processing and stability of freeze-dried ginger juice powder].

PubMed

Yang, Chun-Yu; Guo, Feng-Qian; Zang, Chen; Cao, Hui; Zhang, Bao-Xian

2018-02-01

Ginger juice， a commonly used adjuvant for Chinese materia medica， is applied in processing of multiple Chinese herbal decoction pieces. Because of the raw materials and preparation process of ginger juice， it is difficult to be preserved for a long time， and the dosage of ginger juice in the processing can not be determined base on its content of main compositions. Ginger juice from different sources is hard to achieve consistent effect during the processing of traditional Chinese herbal decoction pieces. Based on the previous studies， the freeze drying of ginger juice under different shelf temperatures and vacuum degrees were studied， and the optimized freeze drying condition of ginger juice was determined. The content determination method for 6-gingerol， 8-gingerol， 10-gingerol and 6-shagaol in ginger juice and redissolved ginger juice was established. The content changes of 6-gingerol， 8-gingerol， 10-gingerol， 6-gingerol， 6-shagaol， volatile oil and total phenol were studied through the drying process and 30 days preservation period. The results showed that the freeze drying time of ginger juice was shortened after process optimization; the compositions basically remained unchanged after freeze drying， and there was no significant changes in the total phenol content and gingerol content， but the volatile oil content was significantly decreased( P <0.05). Within 30 days， the contents of gingerol， total phenol， and volatile oil were on the decline as a whole. This study has preliminarily proved the feasibility of freeze-drying process of ginger juice as an adjuvant for Chinese medicine processing. Copyright© by the Chinese Pharmaceutical Association.

Preliminary assestment of lint cotton water content in gin-drying temperature studies

USDA-ARS?s Scientific Manuscript database

Prior studies to measure total water (free and bound) in lint cotton by Karl Fischer Titration showed the method is more accurate and precise than moisture content by standard oven drying. The objective of the current study was to compare the moisture and total water contents from five cultivars de...

Spatial distribution of particulate organic matter pools, quantified and characterized by mid-infrared spectroscopy

NASA Astrophysics Data System (ADS)

Bornemann, L.; Welp, G.; Amelung, W.

2009-04-01

Comprising more than 60 % of the terrestrial carbon pool, soil organic carbon (SOC) is one of the principal factors regulating the global C-cycle. Against the background of worldwide increasing CO2 emissions, much effort has been put to the modelling of soil-C turnover in order to evaluate its potential for mitigation of climate change. Soil organic matter is an ever changing assemblage of various organic components that interact with the mineral matrix and in dependence of its ecological environment. Carbon storage is thereby assumed to propagate by hierarchical saturation of different carbon pools. A homogeneous distribution of the respective pools within natural environments is unlikely as the controlling soil parameters are subject to spatial and temporal heterogeneity. Several attempts to operationalize this complex soil compartment have been proposed, most of them resting upon a concept of pools with different stability and varying turnover times. Among these pools, particulate organic matter (POM) is considered to be most sensitive to environmental changes and has been shown to explain major parts of the SOC variations. Until today, rather laborious physical and physico-chemical fractionation procedures are most commonly applied for the initialization and validation of POM in C-turnover models. Mid-infrared spectroscopy (MIRS) in combination with partial least squares regression (PLSR) could overcome this problem. The technique is fast, cheap, and requires little sample preparation. All the same, it is an appropriate technique not only for the determination of gross parameters like total soil organic carbon contents, but also for the determination and characterization of minor constituents like black carbon in soils. Basically, the infrared radiation is absorbed by molecules that express a dipole-moment during vibration. As virtually all constituents of soil organic matter and also a multitude of inorganic soil constituents express such a dipole-moment, plentiful chemical information can be extracted from absorption spectra of soil samples. In this work we present the development of calibration models for POM quantification via MIRS-PLSR, and the compilation of a raster data set including SOC and POM of three size classes for the testsite of the SFB-TR32 at Selhausen near Jülich (Germany). The studied test site is an orthic luvisol which has been sampled in a ten times ten meter raster from 0-30 cm depth (n=131). For POM fractionation samples were gently sonicated and material from 2000-250 µm was gained by wet sieving. After a second, more intense sonication, intermediate (250-53 µm) and fine (53-20 µm) material was also gained by wet sieving. All fractions were dried at 40 °C, carbon contents were determined by elemental analysis. For calibration of MIRS-PLSR, SOC contents of 87 bulk soil samples were determined by elemental analysis. Contributions of the different POM fractions to bulk SOC as well as the SOC contents within the particular POM fraction were determined for 36 soil samples by physical particle size fractionation as described above. MIRS-PLSR based predictions for the contribution of POM fractions to bulk soil proved to be satisfactory (R² >0.77) and improved with decreasing particle size. For the predictions of SOC contents in bulk soil and the different POM fractions R² even reached values ≥0.97. Root mean squared errors of the cross validations were in the range of standard deviations of the lab analysis or smaller. As physical fractionation methods are intrinsically susceptible to measurement errors, determination of POM fractions by MIRS analysis may even improve data sets for modelling. Apart from the generally convincing statistical parameters, further evidence for reliable predictions of the contributions of the different POM fractions to bulk SOC could be drawn from the spectral information itself. The spectral features utilized for the determination of the contribution of the different POM fractions to bulk SOC were matching the features for the prediction of the absolute SOC concentrations within the particular fractions. As these predictions were conducted with independent sample sets (bulk soil for the POM contribution and soil fractions for the SOC content within the fraction) the matching structural information for both features of the individual POM fraction indirectly validates the prediction for the POM pools. The latter is especially true as the observed features coincide with the actual knowledge on chemistry and stabilization of POM in soils. For the compilation of a complete raster data-set, the developed calibrations were applied to all of the 131 topsoil samples taken at the SFB-TR32 testsite. Correlation analysis indicated that the coarse and the intermediate POM fractions are related to each other, to bulk SOC content and textural parameters respectively, while the fine POM fraction seems to be independent from these factors. The observed coherences and the applicability of a C-saturation concept will be discussed by visual map-comparison and geostatistical analysis of the determined parameters.

Quantifying the heterogeneity of soil compaction, physical soil properties and soil moisture across multiple spatial scales

NASA Astrophysics Data System (ADS)

Coates, Victoria; Pattison, Ian; Sander, Graham

2016-04-01

England's rural landscape is dominated by pastoral agriculture, with 40% of land cover classified as either improved or semi-natural grassland according to the Land Cover Map 2007. Since the Second World War the intensification of agriculture has resulted in greater levels of soil compaction, associated with higher stocking densities in fields. Locally compaction has led to loss of soil storage and an increased in levels of ponding in fields. At the catchment scale soil compaction has been hypothesised to contribute to increased flood risk. Previous research (Pattison, 2011) on a 40km2 catchment (Dacre Beck, Lake District, UK) has shown that when soil characteristics are homogeneously parameterised in a hydrological model, downstream peak discharges can be 65% higher for a heavy compacted soil than for a lightly compacted soil. However, at the catchment scale there is likely to be a significant amount of variability in compaction levels within and between fields, due to multiple controlling factors. This research focusses in on one specific type of land use (permanent pasture with cattle grazing) and areas of activity within the field (feeding area, field gate, tree shelter, open field area). The aim was to determine if the soil characteristics and soil compaction levels are homogeneous in the four areas of the field. Also, to determine if these levels stayed the same over the course of the year, or if there were differences at the end of the dry (October) and wet (April) periods. Field experiments were conducted in the River Skell catchment, in Yorkshire, UK, which has an area of 120km2. The dynamic cone penetrometer was used to determine the structural properties of the soil, soil samples were collected to assess the bulk density, organic matter content and permeability in the laboratory and the Hydrosense II was used to determine the soil moisture content in the topsoil. Penetration results show that the tree shelter is the most compacted and the open field area is least compacted in both periods. The falling head test showed that soil permeability was lowest around the feeding area and highest in the open field area in both periods. Laboratory tests showed that the tree shelter had the lowest bulk density values, due to the higher levels of organic matter content and the field gate had the highest levels of bulk density in both periods. There was also a significant difference in bulk density at the field gate and open field areas between the two periods. These results highlight statistically significant differences between heavily compacted areas where animals congregate and less-trampled areas of the field.

Common relationships among proximate composition components in fishes

USGS Publications Warehouse

Hartman, K.J.; Margraf, F.J.

2008-01-01

Relationships between the various body proximate components and dry matter content were examined for five species of fishes, representing anadromous, marine and freshwater species: chum salmon Oncorhynchus keta, Chinook salmon Oncorhynchus tshawytscha, brook trout Salvelinus fontinalis, bluefish Pomatomus saltatrix and striped bass Morone saxatilis. The dry matter content or per cent dry mass of these fishes can be used to reliably predict the per cent composition of the other components. Therefore, with validation it is possible to estimate fat, protein and ash content of fishes from per cent dry mass information, reducing the need for costly and time-consuming laboratory proximate analysis. This approach coupled with new methods of non-lethal estimation of per cent dry mass, such as from bioelectrical impedance analysis, can provide non-destructive measurements of proximate composition of fishes. ?? 2008 The Authors.

Cryopreservation of lipid-rich seeds: effect of moisture content and cooling rate on germination.

PubMed

González-Benito, E M; Pérez-García, F

2001-01-01

The effect of fast and slow cooling on germination of seeds from two Brassicaceae species (Eruca vesicaria (L.) Cav., Brassica napus L. var. oleifera (Moench) DC cv. Bingo) and cypselas from three Compositae species (Onopordum nervosum Boiss., Onopordum acanthium L., Helianthus annuus L. cv. Viky) at different moisture contents was studied. Seed lipid content (dry weight basis) ranged from 15% (O. nervosum) to 41% (H. annuus). For each species, seeds with four moisture contents were cryopreserved either by direct immersion in liquid nitrogen or by previous cooling at 10 degrees C/min from room temperature to -50 degrees C. In three species (E. vesicaria, B. napus, and H. annuus) germination of air-dried (6.2-8.9% moisture content) seeds cooled by direct immersion in liquid nitrogen was not significantly different from germination of control seeds (air-dried, non-cooled). In the two Onorpordum species the best response among cooling treatments was observed when air-dried seeds were slowly cooled.

Kinetics, biocompounds, antioxidant activity, and sensory attributes of quinces as affected by drying method.

PubMed

Szychowski, Przemysław J; Lech, Krzysztof; Sendra-Nadal, Esther; Hernández, Francisca; Figiel, Adam; Wojdyło, Aneta; Carbonell-Barrachina, Ángel A

2018-07-30

Quinces are attracting interest due to their health and nutritional benefits. Drying kinetics, bioactive compounds, antioxidant activity, and the main sensory parameters were determined in dried quinces, cultivar Leskovač, as affected by the drying method. The highest total polyphenols content was observed in dried samples obtained after freeze drying and convective drying at 50 °C. The best drying treatment, considering only sensory attributes, was vacuum-microwave drying at 480 W, because it led to intermediate dark color and high intensities of basic tastes and key flavor attributes. The studied parameters were finally used to recommend convective drying at 60 °C as the most appropriate drying method for quinces, because it had a high content of total phenolic compounds (2nd best treatment out of 10), a good sensory profile, was cheap, and caused no negative effects on nutritional or sensory parameters; the only disadvantage was its long drying time. Copyright © 2018 Elsevier Ltd. All rights reserved.

A study on the dewatering of industrial waste sludge by fry-drying technology.

PubMed

Ohm, Tae-In; Chae, Jong-Seong; Kim, Jeong-Eun; Kim, Hee-Kyum; Moon, Seung-Hyun

2009-08-30

In sludge treatment, drying sludge using typical technology with high water content to a water content of approximately 10% is always difficult because of adhesive characteristics of sludge. Many methods have been applied, including direct and indirect heat drying, but these approaches of reducing water content to below 40% after drying is very inefficient in energy utilization of drying sludge. In this study, fry-drying technology with a high heat transfer coefficient of approximately 500 W/m(2) degrees C was used to dry industrial wastewater sludge. Also waste oil was used in the fry-drying process, and because the oil's boiling point is between 240 and 340 degrees C and the specific heat is approximately 60% of that of water. In the fry-drying system, the sludge is input by molding it into a designated form after heating the waste oil at temperatures between 120 and 170 degrees C. At these temperatures, the heated oil rapidly evaporates the water contained in the sludge, leaving the oil itself. After approximately 10 min, the water content of the sludge was less than 10%, and its heating value surpassed 5300 kcal/kg. Indeed, this makes the organic sludge appropriate for use as a solid fuel. The wastewater sludge used in this study was the designated waste discharged from chemical, leather and plating plants. These samples varied in characteristics, especially with regard to heavy metal concentration. After drying the three kinds of wastewater sludge at oil temperatures 160 degrees C for 10 min, it was found that the water content in the sludge from the chemical, leather, and plating plants reduced from 80.0 to 5.5%, 81.6 to 1.0%, and 65.4 to 0.8%, respectively. Furthermore, the heat values of the sludge from the chemical, leather, and plating plants prior to fry-drying were 217, 264, and 428 kcal/kg, respectively. After drying, these values of sludge increased to 5317, 5983 and 6031 kcal/kg, respectively. The heavy metals detected in the sludge after drying were aluminum, lead, zinc, mercury, and cadmium. Most importantly, if the dried sludge is used as a solid fuel, these heavy metals can be collected from the dust collector after combustion.

Relative drying times of 650 tropical woods : estimation by green moisture content, specific gravity, and green weight density

Treesearch

William T. Simpson; John A. Sagoe

1991-01-01

Many tropical species are underutilized because of their varied and frequently unknown drying properties. When handling a large number of species, harvesting and processing the species individually is impractical, and grouping species by similar drying properties is difficult. This report examines the relationship between green moisture content and specific gravity of...

The sedimentary organic matter from a Lake Ichkeul core (far northern Tunisia): Rock-Eval and biomarker approach

NASA Astrophysics Data System (ADS)

Affouri, Hassène; Sahraoui, Olfa

2017-05-01

The vertical distributions of bulk and molecular biomarker composition in samples from a ca. 156 cm sediment core from Lake Ichkeul were determined. Bulk analysis (Rock-Eval pyrolysis, carbonate, lipid extraction) and molecular analysis of saturated fractions were used to characterize the nature, preservation conditions and input of sedimentary organic matter (OM) to this sub-wet lake environment. The sediments are represented mainly by gray-black silty-clay facies where the carbonate (CaCO3) content varies in a range of 10-30% dry sediment. Rock-Eval pyrolysis revealed a homogeneous total organic carbon (TOC) content of ca. 1% sediment, but with down core fluctuation, indicating different anoxic conditions at different depths and material source variation. The values show three periods of relative enrichment, exceeding ca. 1%, at 146-134 cm, 82 cm and 14-0 cm depth. The low Hydrogen Index (HI) values [<119 mg hydrocarbon (HC)/g TOC)] were characteristic of continental Type III OM. The Tmax values in the range 415-420 °C were characteristic of immature OM at an early diagenetic stage. The distributions of n-alkanes (C17 to C34), isoprenoid (iso) alkanes (pristane and phytane), terpanes and steranes showed that the OM is a mixture of marine algal and bacterial source and emergent and floating higher plant origin. In addition, the distributions, as well as several biomarker ratios (n-alkanes, iso-alkanes/n-alkanes), showed that the OM is a mixture of immature and mature. Significant downcore fluctuation was observed in the molecular composition. This indicates intense microbial activity below ca. 50 cm core depth under an anoxic and brackish environment.

The Production of a Stable Infliximab Powder: The Evaluation of Spray and Freeze-Drying for Production

PubMed Central

Kanojia, Gaurav; Have, Rimko ten; Bakker, Arjen; Wagner, Koen; Frijlink, Henderik W.; Kersten, Gideon F. A.; Amorij, Jean-Pierre

2016-01-01

In prospect of developing an oral dosage form of Infliximab, for treatment of Crohn’s disease and rheumatoid arthritis, freeze-drying (vial vs Lyoguard trays) and spray-drying were investigated as production method for stable powders. Dextran and inulin were used in combination with sucrose as stabilizing excipients. The drying processes did not affect Infliximab in these formulations, i.e. both the physical integrity and biological activity (TNF binding) were retained. Accelerated stability studies (1 month at 60°C) showed that the TNF binding ability of Infliximab was conserved in the freeze-dried formulations, whereas the liquid counterpart lost all TNF binding. After thermal treatment, the dried formulations showed some chemical modification of the IgG in the dextran-sucrose formulation, probably due to Maillard reaction products. This study indicates that, with the appropriate formulation, both spray-drying and freeze-drying may be useful for (bulk) powder production of Infliximab. PMID:27706175

Hair Shaft Damage from Heat and Drying Time of Hair Dryer

PubMed Central

Lee, Yoonhee; Kim, Youn-Duk; Hyun, Hye-Jin; Pi, Long-quan; Jin, Xinghai

2011-01-01

Background Hair dryers are commonly used and can cause hair damage such as roughness, dryness and loss of hair color. It is important to understand the best way to dry hair without causing damage. Objective The study assessed changes in the ultra-structure, morphology, moisture content, and color of hair after repeated shampooing and drying with a hair dryer at a range of temperatures. Methods A standardized drying time was used to completely dry each hair tress, and each tress was treated a total of 30 times. Air flow was set on the hair dryer. The tresses were divided into the following five test groups: (a) no treatment, (b) drying without using a hair dryer (room temperature, 20℃), (c) drying with a hair dryer for 60 seconds at a distance of 15 cm (47℃), (d) drying with a hair dryer for 30 seconds at a distance of 10 cm (61℃), (e) drying with a hair dryer for 15 seconds at a distance of 5 cm (95℃). Scanning and transmission electron microscopy (TEM) and lipid TEM were performed. Water content was analyzed by a halogen moisture analyzer and hair color was measured with a spectrophotometer. Results Hair surfaces tended to become more damaged as the temperature increased. No cortex damage was ever noted, suggesting that the surface of hair might play a role as a barrier to prevent cortex damage. Cell membrane complex was damaged only in the naturally dried group without hair dryer. Moisture content decreased in all treated groups compared to the untreated control group. However, the differences in moisture content among the groups were not statistically significant. Drying under the ambient and 95℃ conditions appeared to change hair color, especially into lightness, after just 10 treatments. Conclusion Although using a hair dryer causes more surface damage than natural drying, using a hair dryer at a distance of 15 cm with continuous motion causes less damage than drying hair naturally. PMID:22148012

Preparation and characterization of starch-based loose-fill packaging foams

NASA Astrophysics Data System (ADS)

Fang, Qi

Regular and waxy corn starches were blended in various ratios with biodegradable polymers including polylactic acid (PLA), Eastar Bio Copolyester 14766 (EBC) and Mater-Bi ZF03U (MBI) and extruded with a C. W. Brabender laboratory twin screw extruder using a 3-mm die nozzle at 150°C and 150 rev/min. Physical characteristics including radial expansion, unit density and bulk density and water solubility index, water absorption characteristics, mechanical properties including compressibility, Young's modulus, spring index, bulk compressibility and bulk spring index and abrasion resistance were investigated as affected by the ingredient formulations, i.e. type of polymers, type of starches, polymer to starch ratio and starch moisture content. A completely randomized factorial blocking experimental design was used. Fifty-four treatments resulted. Each treatment was replicated three times. SAS statistical software package was used to analyze the data. Foams made of waxy starch had better radial expansion, lower unit density and bulk density than did foams made of regular starch. Regular starch foams had significantly lower water solubility index than did the waxy starch foams. PLA-starch foams had the lowest compressibility and Young's modulus. MBI-starch foams were the most rigid. All foams had excellent spring indices and bulk spring indices which were comparable to the spring index of commercial expanded polystyrene foam. Correlations were established between the foam mechanical properties and the physical characteristics. Foam compressibility and Young's modulus decreased as increases in radial expansion and decreases in unit and bulk densities. Their relationships were modeled with power law equations. No correlation was observed between spring index and bulk spring index and foam physical characteristics. MBI-starch foams had the highest equilibrium moisture content. EBC-starch and PLA-starch foams had similar water absorption characteristics. No significant difference existed in water absorption characteristics between foams made of regular and waxy starches. Empirical models were developed to correlate foam water absorption characteristics with relative humidity and polymer content. The developed models fit the data well with relatively small standard errors and uniformly scattered residual plots. Foams with higher polymer content had better abrasion resistance than did foams with lower polymer content.

49 CFR 178.1050 - Top lift test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... designed to be lifted from the top, there may be no damage to the Flexible Bulk Container or its lifting devices that renders the Flexible Bulk Container unsafe for transport, and no loss of contents. ... permissible gross mass, the load being evenly distributed. (c) Test method. (1) A Flexible Bulk Container must...

49 CFR 178.1050 - Top lift test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... designed to be lifted from the top, there may be no damage to the Flexible Bulk Container or its lifting devices that renders the Flexible Bulk Container unsafe for transport, and no loss of contents. ... permissible gross mass, the load being evenly distributed. (c) Test method. (1) A Flexible Bulk Container must...

Effect of microwave drying and oven drying on the water activity, color, phenolic compounds content and antioxidant activity of coconut husk (Cocos nucifera L.).

PubMed

Valadez-Carmona, Lourdes; Cortez-García, Rosa María; Plazola-Jacinto, Carla Patricia; Necoechea-Mondragón, Hugo; Ortiz-Moreno, Alicia

2016-09-01

The coconut ( Cocos nucifera L.) husk is basically composed by fiber and pith material and remained under-utilized. This is an important source of phenolic compounds that could be used as functional ingredients. The aim of this study was to determine the effect of: oven-drying (OD) and microwave drying (MD), on the water activity, color, phenolic compound content and antioxidant activity of coconut husk. The OD was performed at 60 °C for 12 h and MD was performed at 900 W for 10 min. The total phenolic content (TPC) in fresh coconut husk was 64.2 mg GAE/g dry wt and significant higher than observed after OD and MD of 35.8 and 45.5 mg GAE/g dry wt, respectively. Ten phenols were identified in fresh and dehydrated coconut husks. The husk MD showed an increase in the content of gallic, 4-hydroxybenzoic, ferulic and syringic acids and epicatechin compared with the fresh; while coconut husk OD and MD, showed a decrease in the content of vanillic acid, vanillin, catequin and kaempferol. The antioxidant activity decreased after both OD and MD. However, MD resulted in a better antioxidant activity in husk than OD. MD of husk resulted into better retention of preserved color, TPC and TFC than OD.

Feasibility Report and Environmental Impact Statement for Navigation and Related Purposes

DTIC Science & Technology

1980-07-01

Sacramento since the port’s service area produces large quantities of rice, other grains, wood chips, and other dry bulk products required in the...1979 were rice, wood chips, other grains and oilseeds, and fertilizer. The total tonnage for these cargoes accounted for 91 percent of the port’s...promising to the port’s future are rice, other grains and oilseeds, logs, wood chips, fertilizers and fertilizer materials, and other bulk commodities

Stable carbon and nitrogen isotopes in vertical peat profiles of natural and drained boreal peatlands

NASA Astrophysics Data System (ADS)

Nykänen, Hannu; Mpamah, Promise; Rissanen, Antti; Pitkänen, Aki; Turunen, Jukka; Simola, Heikki

2015-04-01

Peatlands form a significant carbon pool in the global carbon cycle. Change in peat hydrology, due to global warming is projected to change microbiological processes and peat carbon pool. We tested if bulk stable carbon and nitrogen isotopes serve as indicators of severe long term drying in peatlands drained for forestry. Depth profile analysis of peat, for their carbon and nitrogen content as well as their carbon and nitrogen stable isotopic signatures, were conducted for peatlands in southern and eastern Finland, having ombrotrophic and minerotrophic natural and corresponding drained pairs or separate drained sites. The selection of sites allowed us to compare changes due to different fertility and changes due to long term artificial drying. Drainage lasting over 40 years has led to changes in hydrology, vegetation, nutrient mineralization and respiration. Furthermore, increased nutrient uptake and possible recycling of peat nitrogen and carbon trough vegetation back to the peat surface, also possibly has an effect on the stable isotopic composition of peat carbon and nitrogen. We think that drainage induced changes somehow correspond to those caused by changed hydrology due to climate change. We will present data from these measurements and discuss their implications for carbon and nitrogen flows in peatlands.

Improvements In solar dry kiln design

Treesearch

E. M. Wengert

1971-01-01

Interest in solar drying of lumber has increased in recent years because previous results had indicated that: Drying times are shorter and final moisture contents are lower in solar drying than in air drying; much less lumber degrade occurs in solar drying when compared to air drying; and the cost of energy is less in solar drying than in kiln drying. Work in the field...

Physico-chemical properties of instant ogbono (Irvingia gabonensis) mix powder

PubMed Central

Bamidele, Oluwaseun P; Ojedokun, Omotayo S; Fasogbon, Beatrice M

2015-01-01

The main objective of the research is to develop a recipe of instant dry soup mix for easy preparation of ogbono soup. Instant ogbono mix powder was processed using common locally ingredients. Dika kernel powder, dried ugwu leaf, crayfish, stock fish, and a mixture of locust bean, onion, seasoning and Cameroon powder were formulated at different ratios to find the best acceptable ogbono mix powder. The samples were subjected to proximate, functional, vitamin, mineral, and sensory analyses. The formulated sample D with the highest ratio of crayfish and stock fish had the highest value of protein and carbohydrate (24.13 and 35.61%, respectively). The control sample (100% dika kernel powder) was low in moisture content (6.20%) but high in crude fat, other samples followed in this order (control > A > B > C > D) for crude fat. Ash, crude fiber, and carbohydrate showed a significant difference (P < 0.05) in all the samples. The functional properties of the sample showed a significant difference (P < 0.05) in all the samples with the control having the highest value for the water absorption, swelling capacity, and bulk density which may be due to the high crude fiber and low moisture content recorded for the control sample in the proximate analysis. The mineral content of all the samples were higher than the control with phosphorous having the highest value and iron the least value. Vitamin C was the main dominating vitamin in the sample followed by vitamin B2, vitamin A, and vitamin B3. The sensory evaluation revealed that 100% dika kernel powder gave a good attribute of the soup but with less nutritional composition, while some formulated samples showed a similar attribute with higher nutritional value. Sample A with the highest overall acceptability had the best attribute of ogbono soup. Instant ogbono mix powder has higher nutritional value and easy to cook. PMID:26288723

Odor volatiles associated with microflora in damp ventilated and non-ventilated bin-stored bulk wheat.

PubMed

Tuma, D; Sinha, R N; Muir, W E; Abramson, D

1989-05-01

Western hard red spring wheat, stored at 20 and 25% moisture contents for 10 months during 1985-86, was monitored for biotic and abiotic variables in 10 unheated bins in Winnipeg, Manitoba. The major odor volatiles identified were 3-methyl-1-butanol, 3-octanone and 1-octen-3-ol. The production of these volatiles was associated and correlated with microfloral infection. Ventilation, used for cooling and drying of grain, disrupted microfloral growth patterns and production of volatiles. The highest levels of 3-methyl-1-butanol occurred in 25% moisture content wheat infected with bacteria, Penicillium spp. and Fusarium spp. In non-ventilated (control) bins with 20% moisture content wheat, 3-methyl-1-butanol was correlated with infection by members of the Aspergillus glaucus group and bacteria. In control bins, 1-octen-3-ol production was correlated with infection of wheat of both moisture contents by Penicillium spp. The fungal species, isolated from damp bin-stored wheat and tested for production of odor volatiles on wheat substrate, included Alternaria alternata (Fr.) Keissler, Aspergillus repens (Corda) Saccardo, A. flavus Link ex Fries, A. versicolor (Vuill.) Tiraboschi, Penicillium chrysogenum Thom, P. cyclopium Westling, Fusarium moniliforme Sheldon, F. semitectum (Cooke) Sacc. In the laboratory, fungus-inoculated wheat produced 3-methyl-1-butanol; 3-octanone and 1-octen-3-ol were also produced, but less frequently. Two unidentified bacterial species isolated from damp wheat and inoculated on agar produced 3-methyl-1-butanol.

Core Versus Nuclear Gauge Methods of Determining Soil Bulk Density and Moisture Content

Treesearch

Jacqueline G. Steele; Jerry L. Koger; Albert C. Trouse; Donald L. Sirois

1983-01-01

Soil bulk and moisture content measurements were obtained using two nuclear gauge systems and those compared to those obtained from soil cores. The soils, a Hiwassee sandy loam, a Lakeland loamy sand, and a Loyd clay, were free of organic matter and uniform in mechanical composition. The regression equations developed for the nuclear guages for the first phase of the...

Unsaturated flow in a centrifugal field: Measurement of hydraulic conductivity and testing of Darcy's Law

USGS Publications Warehouse

Nimmo, J.R.; Rubin, J.; Hammermeister, D.P.

1987-01-01

A method has been developed to establish steady state flow of water in an unsaturated soil sample spinning in a centrifuge. Theoretical analysis predicts moisture conditions in the sample that depend strongly on soil type and certain operating parameters. For Oakley sand, measurements of flux, water content, and matric potential during and after centrifugation verify that steady state flow can be achieved. Experiments have confirmed the theoretical prediction of a nearly uniform moisture distribution for this medium and have demonstrated that the flow can be effectively one-dimensional. The method was used for steady state measurements of hydraulic conductivity K for relatively dry soil, giving values as low as 7.6 × 10−11 m/s with data obtained in a few hours. Darcy's law was tested by measuring K for different centrifugal driving forces but with the same water content. For the sand at a bulk density of 1.82 Mg/m3 and 27% saturation, results were consistent with Darcy's law for K equal to 5.22 × 10−10 m/s and forces ranging from 216 to 1650 times normal gravity.

Cu-Chitosan Nanoparticle Mediated Sustainable Approach To Enhance Seedling Growth in Maize by Mobilizing Reserved Food.

PubMed

Saharan, Vinod; Kumaraswamy, R V; Choudhary, Ram Chandra; Kumari, Sarita; Pal, Ajay; Raliya, Ramesh; Biswas, Pratim

2016-08-10

Food crop seedlings often have susceptibility to various abiotic and biotic stresses. Therefore, in the present study, we investigated the impact of Cu-chitosan nanoparticles (NPs) on physiological and biochemical changes during maize seedling growth. Higher values of percent germination, shoot and root length, root number, seedling length, fresh and dry weight, and seed vigor index were obtained at 0.04-0.12% concentrations of Cu-chitosan NPs as compared to water, CuSO4, and bulk chitosan treatments. Cu-chitosan NPs at the same concentrations induced the activities of α-amylase and protease enzymes and also increased the total protein content in germinating seeds. The increased activities of α-amylase and protease enzymes corroborated with decreased content of starch and protein, respectively, in the germinating seeds. Cu-chitosan NPs at 0.16% and CuSO4 at 0.01% concentrations showed inhibitory effect on seedling growth. The observed results on seedling growth could be explained by the toxicity of excess Cu and growth promotory effect of Cu-chitosan NPs. Physiological and biochemical studies suggest that Cu-chitosan NPs enhance the seedling growth of maize by mobilizing the reserved food, primarily starch, through the higher activity of α-amylase.

Extraction of polysaccharide from fruits of Cordia dichotoma G. Forst using acid precipitation method and its physicochemical characterization.

PubMed

Pawar, Harshal Ashok; Gavasane, Amit Jagannath; Choudhary, Pritam Dinesh

2018-08-01

The objective of the present work was to isolate and characterize polysaccharide from fruits of Cordia dichotoma G. Forst. (Family Boraginaceae). Polysaccharide was isolated by using 1% Hydrochloric acid solution. The isolated polysaccharide was tested for physicochemical characteristics such as solubility, pH (1% w/w in water), swelling capacity, loss on drying, ash value, bulk and tapped density, Carr's capacity, Hausner's ratio and angle of repose. Also isolated polysaccharide was characterized by Differential scanning colorimeter (DSC), Estimation of total sugar content, Rheological study and infrared spectroscopy (FT-IR). The isolated mucilage showed positive results for Molisch's test and negative for Ruthenium red test which indicated presence of carbohydrate and gum. The result of physicochemical characteristics reveals that isolated Cordia dichotoma polysaccharide possesses good flow properties. The total polysaccharide content of Cordia dichotoma polymer isolate was found to be 86.24% (w/w). From this study it can be concluded that the polysaccharide isolated from Cordia dichotoma fruits has the required properties and could be used as an excipient for pharmaceutical dosage forms. Copyright © 2018 Elsevier B.V. All rights reserved.

Isolation, characterization and investigation of Cordia dichotoma fruit polysaccharide as a herbal excipient.

PubMed

Pawar, Harshal Ashok; Jadhav, Pravin

2015-01-01

The objective of the present research work was to isolate, purify and characterize Cordia dichotoma gum and investigate its disintegration property in oral tablets. The isolated gum was tested for physicochemical characteristics such as solubility, pH (1% w/w in water), swelling index, loss on drying, ash value, bulk and tapped density, Carr's index, Hausner's ratio and angle of repose. The Orodispersible tablets of valsartan were prepared by direct compression method and evaluated for average weight (mg), drug content (%), thickness (mm), hardness (kg/cm(2)), friability (%), wetting time (sec), water absorption ratio (%) and disintegration time (sec). FTIR studies revealed that there was no interaction between drug, gum and other excipients used in the study. The F4 batch with disintegration time 26.34 ± 0.78 s and in vitro release 99.64 ± 0.43% was selected as optimized formulation. This formulation was compared with conventional marketed formulation and was found superior. Batch F4 was subjected to stability studies for three months and was tested for its disintegration time, drug contents and dissolution behaviour. Batch F4 was found stable for three months at accelerated temperature. Copyright © 2014 Elsevier B.V. All rights reserved.

Are stag beetles fungivorous?

PubMed

Tanahashi, Masahiko; Matsushita, Norihisa; Togashi, Katsumi

2009-11-01

Stag beetle larvae generally feed on decaying wood; however, it was unknown whether they can use wood-rotting fungi alone as food. Here, to clarify this, newly hatched larvae of Dorcus rectus (Motschulsky) (Coleoptera: Lucanidae) were reared for 14 days on artificial diets containing a fixed amount of freeze-dried mycelia of the following fungi: Bjerkandera adusta, Trametes versicolor, Pleurotus ostreatus, and Fomitopsis pinicola. The mean incremental gain in larval body mass was greatest on diets containing B. adusta, followed by T. versicolor, P. ostreatus, and F. pinicola. The growth rate of body mass correlated positively with mycelial nitrogen content of the different fungi. It also correlated positively with the mycelial content of B. adusta in the diet. Addition of antibiotics to diets with mycelia nearly halved larval growth, indicating that larvae were able to use fungal mycelia as food without the assistance of associated microbes although the microbes positively affected larval growth. Four newly hatched larvae reared on artificial diets containing B. adusta mycelia developed to the second instar in 21-34 days; and one developed to the third (=final) instar. This study provides evidence that fungi may constitute the bulk of the diet of D. rectus larvae.

Collaborative studies on the development of national reference standards for potency determination of H7N9 influenza vaccine

PubMed Central

Li, Changgui; Xu, Kangwei; Hashem, Anwar; Shao, Ming; Liu, Shuzhen; Zou, Yong; Gao, Qiang; Zhang, Yongchao; Yuan, Liyong; Xu, Miao; Li, Xuguang; Wang, Junzhi

2015-01-01

The outbreak of human infections of a novel avian influenza virus A (H7N9) prompted the development of the vaccines against this virus. Like all types of influenza vaccines, H7N9 vaccine must be tested for its potency prior to being used in humans. However, the unavailability of international reference reagents for the potency determination of H7N9 vaccines substantially hinders the progress in vaccine development. To facilitate clinical development, we enlisted 5 participants in a collaborative study to develop critical reagents used in Single Radial Immunodiffusion (SRID), the currently acceptable assay for potency determination of influenza vaccine. Specifically, the hemagglutinin (HA) content of one vaccine bulk for influenza A (H7N9), herein designated as Primary Liquid Standard (PLS), was determined by SDS-PAGE. In addition, the freeze-dried antigen references derived from PLS were prepared to enhance the stability for long term storage. The final HA content of lyophilized antigen references were calibrated against PLS by SRID assay in a collaborative study. Importantly, application of these national reference standards to potency analyses greatly facilitated the development of H7N9 vaccines in China. PMID:25970793

Geochemical heterogeneity in a sand and gravel aquifer: Effect of sediment mineralogy and particle size on the sorption of chlorobenzenes

USGS Publications Warehouse

Barber, L.B.; Thurman, E.M.; Runnells, D.R.; ,

1992-01-01

The effect of particle size, mineralogy and sediment organic carbon (SOC) on solution of tetrachlorobenzene and pentachlorobenzene was evaluated using batch-isotherm experiments on sediment particle-size and mineralogical fractions from a sand and gravel aquifer, Cape Cod, Massachusetts. Concentration of SOC and sorption of chlorobenzenes increase with decreasing particle size. For a given particle size, the magnetic fraction has a higher SOC content and sorption capacity than the bulk or non-magnetic fractions. Sorption appears to be controlled by the magnetic minerals, which comprise only 5-25% of the bulk sediment. Although SOC content of the bulk sediment is < 0.1%, the observed sorption of chlorobenzenes is consistent with a partition mechanism and is adequately predicted by models relating sorption to the octanol/water partition coefficient of the solute and SOC content. A conceptual model based on preferential association of dissolved organic matter with positively-charged mineral surfaces is proposed to describe micro-scale, intergranular variability in sorption properties of the aquifer sediments.The effect of particle size, mineralogy and sediment organic carbon (SOC) on sorption of tetrachlorobenzene and pentachlorobenzene was evaluated using batch-isotherm experiments on sediment particle-size and mineralogical fractions from a sand and gravel aquifer, Cape Cod, Massachusetts. Concentration of SOC and sorption of chlorobenzenes increase with decreasing particle size. For a given particle size, the magnetic fraction has a higher SOC content and sorption capacity than the bulk or non-magnetic fractions. Sorption appears to be controlled by the magnetic minerals, which comprise only 5-25% of the bulk sediment. Although SOC content of the bulk sediment is <0.1%, the observed sorption of chlorobenzenes is consistent with a partition mechanism and is adequately predicted by models relating sorption to the octanol/water partition coefficient of the solute and SOC content. A conceptual model based on preferential association of dissolved organic matter with positively-charged mineral surfaces is proposed to describe micro-scale, intergranular variability in sorption properties of the aquifer sediments.

Vis-NIR hyperspectral imaging in visualizing moisture distribution of mango slices during microwave-vacuum drying.

PubMed

Pu, Yuan-Yuan; Sun, Da-Wen

2015-12-01

Mango slices were dried by microwave-vacuum drying using a domestic microwave oven equipped with a vacuum desiccator inside. Two lab-scale hyperspectral imaging (HSI) systems were employed for moisture prediction. The Page and the Two-term thin-layer drying models were suitable to describe the current drying process with a fitting goodness of R(2)=0.978. Partial least square (PLS) was applied to correlate the mean spectrum of each slice and reference moisture content. With three waveband selection strategies, optimal wavebands corresponding to moisture prediction were identified. The best model RC-PLS-2 (Rp(2)=0.972 and RMSEP=4.611%) was implemented into the moisture visualization procedure. Moisture distribution map clearly showed that the moisture content in the central part of the mango slices was lower than that of other parts. The present study demonstrated that hyperspectral imaging was a useful tool for non-destructively and rapidly measuring and visualizing the moisture content during drying process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Changes in non-volatile taste components of button mushroom (Agaricus bisporus) during different stages of freeze drying and freeze drying combined with microwave vacuum drying.

PubMed

Pei, Fei; Shi, Ying; Gao, Xingyang; Wu, Fangning; Mariga, Alfred Mugambi; Yang, Wenjian; Zhao, Liyan; An, Xinxin; Xin, Zhihong; Yang, Fangmei; Hu, Qiuhui

2014-12-15

Button mushroom slices were dehydrated using freeze drying (FD) or FD combined with microwave vacuum drying (FMVD), and the non-volatile component profiles were studied. The results showed that the level of non-volatile components in button mushroom firstly increased during sublimation of FD/FMVD process and then fell during desorption in FD process and MVD in FMVD process. Compared to FD products, the contents of soluble sugars and polyols in FMVD products were relatively low, whereas the contents of total free amino acids were significantly higher, close to the level of fresh mushroom. However, there was no significant difference in the contents of 5'-nucleotides and organic acids between FD and FMVD products. The equivalent umami concentration (EUC) values for FD and FMVD products did not differ from fresh, indicating that both drying methods could effectively preserve MSG (monosodium glutamate)-like components in button mushroom. Copyright © 2014 Elsevier Ltd. All rights reserved.

Study of the optimisation of puffing characteristics of potato cubes by spouted bed drying enhanced with microwave.

PubMed

Yan, Wei-qiang; Zhang, Min; Huang, Lue-lue; Tang, Juming; Mujumdar, Arun S; Sun, Jin-cai

2010-06-01

In commercial deep-fat frying of potato chips, the oil content of the final products ranges from 35 to 45 g 100 g(-1) (wet basis). High-temperature frying may cause the formation of acrylamide, making the products unhealthy to the consumer. The aim of this research was to explore a new method, spouted bed microwave drying, to produce healthier puffed snack potato cubes as possible alternatives to oil-fried potato chips. The influence of drying conditions of the spouted bed microwave drying on puffing characteristics of potato cubes were studied and compared with the direct microwave and hot air drying method. Tandem combination drying of microwave-enhanced spouted bed drying (MWSB) could achieve a good expansion ratio, breaking force and rehydration ratio. The puffing characteristics of potato cubes were significantly affected (P < 0.05) by moisture content before starting microwave power in spouted bed microwave drying, by microwave (MW) power, and by the original size of potato cubes. The optimum processing parameters were the moisture content at the start of microwave power (60%), the size of potato cubes (10-12 mm), and microwave power (2-2.5 W g(-1)) Copyright (c) 2010 Society of Chemical Industry.

The Change of Total Anthocyanins in Blueberries and Their Antioxidant Effect After Drying and Freezing

PubMed Central

Srzednicki, George

2004-01-01

This study examined the effects of freezing, storage, and cabinet drying on the anthocyanin content and antioxidant activity of blueberries (Vaccinium corymbosum L). Fresh samples were stored for two weeks at 5°C while frozen samples were kept for up to three months at −20°C. There were two drying treatments, one including osmotic pretreatment followed by cabinet drying and the other involving only cabinet drying. Total anthocyanins found in fresh blueberries were 7.2 ± 0.5 mg/g dry matter, expressed as cyanidin 3-rutinoside equivalents. In comparison with fresh samples, total anthocyanins in untreated and pretreated dried blueberries were significantly reduced to 4.3 ± 0.1 mg/g solid content, 41% loss, and 3.7 ± 0.2 mg/g solid content, 49% loss, respectively. Osmotic treatment followed by a thermal treatment had a greater effect on anthocyanin loss than the thermal treatment alone. In contrast, the frozen samples did not show any significant decrease in anthocyanin level during three months of storage. Measurement of the antioxidant activity of anthocyanin extracts from blueberries showed there was no significant difference between fresh, dried, and frozen blueberries. PMID:15577185

Effect of oven drying and storage on essential oil composition of clove (Syzygium aromaticum) from Toli-Toli

NASA Astrophysics Data System (ADS)

Murni, V. W.; Saepudin, E.; Cahyana, A. H.; Rahayu, D. U. C.; Hastuti, L. T.; Haib, J.

2017-07-01

The research about post-harvested clove is still limited especially in Indonesia, as the biggest producer of clove in the world. The present study was aimed to investigate the effect of drying process and storage on the composition of essential oil of Indonesian clove originated from Toli-Toli. The essential oil of fresh and dried clove was obtained by steam distillation and the composition of the oil was analyzed by gas chromatography-mass spectrometry (GC-MS). In all of the clove oil samples, eugenol was the major component, followed by caryophyllene and acetyleugenol. The drying method used was oven drying at 50°C until clove's moisture content reaches 13±1%. During the drying process, the content of phenylpropanoids such as eugenol, isoeugenol, and chavicol increased, while esters and monoterpenes decreased. The composition of clove oil was studied from dried clove after oven drying, then stored in the laboratory at room temperature for 4 months. There was slightly change on clove oil composition after 4 months of storage. The content of major components of clove like eugenol was higher while acetyleugenol was lower after 4 months of storage.

Influence of air-drying temperature on drying kinetics, colour, firmness and biochemical characteristics of Atlantic salmon (Salmo salar L.) fillets.

PubMed

Ortiz, Jaime; Lemus-Mondaca, Roberto; Vega-Gálvez, Antonio; Ah-Hen, Kong; Puente-Diaz, Luis; Zura-Bravo, Liliana; Aubourg, Santiago

2013-08-15

In this work the drying kinetics of Atlantic salmon (Salmo salar L.) fillets and the influence of air drying temperature on colour, firmness and biochemical characteristics were studied. Experiments were conducted at 40, 50 and 60°C. Effective moisture diffusivity increased with temperature from 1.08×10(-10) to 1.90×10(-10) m(2) s(-1). The colour difference, determined as ΔE values (from 9.3 to 19.3), as well as firmness (from 25 to 75 N mm(-1)) of dried samples increased with dehydration temperature. The lightness value L(∗) and yellowness value b(∗) indicated formation of browning products at higher drying temperatures, while redness value a(∗) showed dependence on astaxanthin value. Compared with fresh fish samples, palmitic acid and tocopherol content decreased in a 20% and 40%, respectively, with temperature. While eicosapentaenoic acid (EPA) content remained unchanged and docosahexaenoic acid (DHA) content changed slightly. Anisidine and thiobarbituric acid values indicated the formation of secondary lipid oxidation products, which is more relevant for longer drying time than for higher drying temperatures. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physico-chemical characteristics of microwave-dried wheat distillers grain with solubles.

PubMed

Mosqueda, Maria Rosario P; Tabil, Lope G; Meda, Venkatesh

2013-01-01

Laboratory-prepared samples of wheat distillers grain with solubles with varying condensed distillers solubles (CDS) content were dried under varying microwave power, and microwave convection settings using a domestic microwave oven to examine their effect on the chemical, structural, color, flow, compression, thermal, and frictional properties of the product, which is dried distillers grain with solubles (DDGS). As CDS level increased, protein and ash content increased, while fat and fiber content decreased in wheat-based DDGS. Fat content was also markedly effected by the microwave oven drying conditions. While CDS level, microwave power or microwave convection setting, and/or their interactions significantly effected a number of physical properties; results indicated that CDS level had a stronger influence compared to the other factors. DDGS samples with high CDS levels were significantly denser, finer but more differentiated in size, less flowable, and less dispersible. These also produced denser and stronger pellets.

Drying-induced physico-chemical changes in cranberry products.

PubMed

Michalska, Anna; Wojdyło, Aneta; Honke, Joanna; Ciska, Ewa; Andlauer, Wilfried

2018-02-01

Sugar-free cranberry juice (XAD) and juice with 15% of maltodextrin were dried by freeze-, vacuum and spray drying methods. Total phenolics (589-6435mg/kg dry matter) including 5 flavonols, 3 phenolic acids, 2 procyanidins and 5 anthocyanins were stronger affected by juice formulation than by drying methods. Spray drying of juice, regardless of its formulation, was competitive to freeze drying in terms of polyphenols' retention. Increase in temperature up to 100°C during vacuum drying of XAD extracts resulted in degradation of polyphenolics (down to 4%), except chlorogenic acid. Its content increased with rise in temperature and accelerated hydroxymethylfurfural formation. The stronger the impact of drying, the more chlorogenic acid is present in cranberry products. In all powders analysed, formation of furoylmethyl amino acids was noted. Antioxidant capacity of cranberry products was influenced by juice formulation and was linked to content of polyphenols. Copyright © 2017 Elsevier Ltd. All rights reserved.

The geochemical and petrological characteristics of prenatal caldera volcano: a case of the newly formed small dacitic caldera, Hijiori, Northeast Japan

NASA Astrophysics Data System (ADS)

Miyagi, Isoji; Kita, Noriko; Morishita, Yuichi

2017-09-01

Evaluating the magma depth and its physical properties is critical to conduct a better geophysical assessment of magma chambers of caldera volcanoes that may potentially cause future volcanic hazards. To understand pre-eruptive conditions of a magma chamber before its first appearance at the surface, this paper describes the case of Hijiori caldera volcano in northeastern Japan, which emerged approximately 12,000 years ago at a place where no volcano ever existed. We estimated the depth, density, bulk modulus, vesicularity, crystal content, and bulk H_2O content of the magma chamber using petrographic interpretations, bulk and microchemical compositions, and thermodynamic calculations. The chemical mass balance calculations and thermodynamic modeling of the erupted magmas indicate that the upper portion of the Hijiori magmatic plumbing system was located at depths between 2 and 4 km, and had the following characteristics: (1) pre-eruptive temperature: about 780 °C; (2) bulk magma composition: 66 ± 1.5 wt% SiO2; (3) bulk magmatic H_2O: approximately 2.5 wt%, and variable characteristics that depend on depth; (4) crystal content: ≤57 vol%; (5) bulk modulus of magma: 0.1-0.8 GPa; (6) magma density: 1.8-2.3 g/cm3; and (7) amount of excess magmatic H_2O: 11-32 vol% or 48-81 mol%. The range of melt water contents found in quartz-hosted melt inclusions (2-9 wt%) suggests the range of depth phenocrysts growth to be wide (2˜13 km). Our data suggest the presence of a vertically elongated magma chamber whose top is nearly solidified but highly vesiculated; this chamber has probably grown and re-mobilized by repeated injections of a small amount of hot dacitic magma originated from the depth.

Optimization of the secondary drying step in freeze drying using TDLAS technology.

PubMed

Schneid, Stefan C; Gieseler, Henning; Kessler, William J; Luthra, Suman A; Pikal, Michael J

2011-03-01

The secondary drying phase in freeze drying is mostly developed on a trial-and-error basis due to the lack of appropriate noninvasive process analyzers. This study describes for the first time the application of Tunable Diode Laser Absorption Spectroscopy, a spectroscopic and noninvasive sensor for monitoring secondary drying in laboratory-scale freeze drying with the overall purpose of targeting intermediate moisture contents in the product. Bovine serum albumin/sucrose mixtures were used as a model system to imitate high concentrated antibody formulations. First, the rate of water desorption during secondary drying at constant product temperatures (-22 °C, -10 °C, and 0 °C) was investigated for three different shelf temperatures. Residual moisture contents of sampled vials were determined by Karl Fischer titration. An equilibration step was implemented to ensure homogeneous distribution of moisture (within 1%) in all vials. The residual moisture revealed a linear relationship to the water desorption rate for different temperatures, allowing the evaluation of an anchor point from noninvasive flow rate measurements without removal of samples from the freeze dryer. The accuracy of mass flow integration from this anchor point was found to be about 0.5%. In a second step, the concept was successfully tested in a confirmation experiment. Here, good agreement was found for the initial moisture content (anchor point) and the subsequent monitoring and targeting of intermediate moisture contents. The present approach for monitoring secondary drying indicated great potential to find wider application in sterile operations on production scale in pharmaceutical freeze drying. © 2011 American Association of Pharmaceutical Scientists

Studying the effect of material initial conditions on drying induced stresses

NASA Astrophysics Data System (ADS)

Heydari, M.; Khalili, K.; Ahmadi-Brooghani, S. Y.

2018-02-01

Cracking as a result of non-uniform deformation during drying is one of defects that may occur during drying and has to be dealt with by proper drying treatment. In the current study the effect of initial condition has been investigated on stress-strain induced by drying. The convective drying of a porous clay-like material has been simulated by using a mathematical model. Mass and heat transfer along with the mechanical behavior of the object being dried make the phenomenon a highly coupled problem. The coupling variables are the solid displacement, moisture content and temperature of the porous medium. A numerical solution is sought and employed to predict the influence of initial conditions of material on the drying induced stresses, the moisture content, and the temperature variations. Simulation results showed that increasing the initial temperature is an effective way to reduce the stresses induced by drying and to obtain products with good quality without significant change in drying curve and in comparison this is more effective than intermittent drying.

Modeling and optimization of red currants vacuum drying process by response surface methodology (RSM).

PubMed

Šumić, Zdravko; Vakula, Anita; Tepić, Aleksandra; Čakarević, Jelena; Vitas, Jasmina; Pavlić, Branimir

2016-07-15

Fresh red currants were dried by vacuum drying process under different drying conditions. Box-Behnken experimental design with response surface methodology was used for optimization of drying process in terms of physical (moisture content, water activity, total color change, firmness and rehydratation power) and chemical (total phenols, total flavonoids, monomeric anthocyanins and ascorbic acid content and antioxidant activity) properties of dried samples. Temperature (48-78 °C), pressure (30-330 mbar) and drying time (8-16 h) were investigated as independent variables. Experimental results were fitted to a second-order polynomial model where regression analysis and analysis of variance were used to determine model fitness and optimal drying conditions. The optimal conditions of simultaneously optimized responses were temperature of 70.2 °C, pressure of 39 mbar and drying time of 8 h. It could be concluded that vacuum drying provides samples with good physico-chemical properties, similar to lyophilized sample and better than conventionally dried sample. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of different drying methods on the product quality and volatile compounds of whole shiitake mushrooms.

PubMed

Tian, Yuting; Zhao, Yingting; Huang, Jijun; Zeng, Hongliang; Zheng, Baodong

2016-04-15

Various drying methods play important roles in the preservation of foods. However, how the different drying methods affect the quality of some foods is not clear. This paper evaluates the effects of hot air, vacuum, microwave, and microwave vacuum drying techniques on important qualities and volatile compounds of whole shiitake (Lentinus edodes) mushrooms. These four drying methods resulted in a significantly (p<0.05) increase in the content of total free amino acids and the relative content of sulfur compounds of dried products. Microwave vacuum drying helped to maintain larger amounts of taste-active amino acids, and improved nutrient retention and color attributes. Furthermore, the uniform honeycomb network created by microwave vacuum drying along with a less collapsed structure of dried samples can be used to explain the observed high rehydration ratio. Therefore, microwave vacuum drying should be a potential method for obtaining high-quality dried mushrooms. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

In-line multipoint near-infrared spectroscopy for moisture content quantification during freeze-drying.

PubMed

Kauppinen, Ari; Toiviainen, Maunu; Korhonen, Ossi; Aaltonen, Jaakko; Järvinen, Kristiina; Paaso, Janne; Juuti, Mikko; Ketolainen, Jarkko

2013-02-19

During the past decade, near-infrared (NIR) spectroscopy has been applied for in-line moisture content quantification during a freeze-drying process. However, NIR has been used as a single-vial technique and thus is not representative of the entire batch. This has been considered as one of the main barriers for NIR spectroscopy becoming widely used in process analytical technology (PAT) for freeze-drying. Clearly it would be essential to monitor samples that reliably represent the whole batch. The present study evaluated multipoint NIR spectroscopy for in-line moisture content quantification during a freeze-drying process. Aqueous sucrose solutions were used as model formulations. NIR data was calibrated to predict the moisture content using partial least-squares (PLS) regression with Karl Fischer titration being used as a reference method. PLS calibrations resulted in root-mean-square error of prediction (RMSEP) values lower than 0.13%. Three noncontact, diffuse reflectance NIR probe heads were positioned on the freeze-dryer shelf to measure the moisture content in a noninvasive manner, through the side of the glass vials. The results showed that the detection of unequal sublimation rates within a freeze-dryer shelf was possible with the multipoint NIR system in use. Furthermore, in-line moisture content quantification was reliable especially toward the end of the process. These findings indicate that the use of multipoint NIR spectroscopy can achieve representative quantification of moisture content and hence a drying end point determination to a desired residual moisture level.

Influence of drying methods over in vitro antitumoral effects of exopolysaccharides produced by Agaricus blazei LPB 03 on submerged fermentation.

PubMed

Fernandes, M B A; Habu, S; de Lima, M A; Thomaz-Soccol, V; Soccol, C R

2011-03-01

Agaricus blazei is a mushroom that belongs to the Brazilian biodiversity and is considered as an important producer of bioactive compounds beneficial to human health. Studies have demonstrated that these compounds present immuno-modulatory, antioxidant and antitumor properties. In order to compare the most used method for fungal polysaccharide drying, lyophilization with other industrial-scale methods, the aim of this work was to submit A. blazei LPB 03 polysaccharide extracts to vaucum, spray and freeze drying, and evaluate the maintenance of its antitumoral effects in vitro. Exopolysaccharides produced by A. blazei LPB 03 on submerged fermentation were extracted with ethanol and submitted to drying processes. The efficiency represents the water content that was removed during the drying process. The resultant dried products showed water content around 3% and water activity less than 0.380, preventing therefore the growth of microorganisms and reactions of chemical degradation. Exopolysaccharide extracts dried by vacuum and spray dryer did not showed any significant cytotoxic effect on cell viability of Wistar mice macrophages. Content of total sugars and protein decrease after drying, nevertheless, 20 mg/ml of exopolysaccharides dried by spray dryer reached 33% of inhibition rate over Ehrlich tumor cells in vitro.

Effects of annealing on the physical properties of therapeutic proteins during freeze drying process.

PubMed

Lim, Jun Yeul; Lim, Dae Gon; Kim, Ki Hyun; Park, Sang-Koo; Jeong, Seong Hoon

2018-02-01

Effects of annealing steps during the freeze drying process on etanercept, model protein, were evaluated using various analytical methods. The annealing was introduced in three different ways depending on time and temperature. Residual water contents of dried cakes varied from 2.91% to 6.39% and decreased when the annealing step was adopted, suggesting that they are directly affected by the freeze drying methods Moreover, the samples were more homogenous when annealing was adopted. Transition temperatures of the excipients (sucrose, mannitol, and glycine) were dependent on the freeze drying steps. Size exclusion chromatography showed that monomer contents were high when annealing was adopted and also they decreased less after thermal storage at 60°C. Dynamic light scattering results exhibited that annealing can be helpful in inhibiting aggregation and that thermal storage of freeze-dried samples preferably induced fragmentation over aggregation. Shift of circular dichroism spectrum and of the contents of etanercept secondary structure was observed with different freeze drying steps and thermal storage conditions. All analytical results suggest that the physicochemical properties of etanercept formulation can differ in response to different freeze drying steps and that annealing is beneficial for maintaining stability of protein and reducing the time of freeze drying process. Copyright © 2017 Elsevier B.V. All rights reserved.

Characterisation of Aronia powders obtained by different drying processes.

PubMed

Horszwald, Anna; Julien, Heritier; Andlauer, Wilfried

2013-12-01

Nowadays, food industry is facing challenges connected with the preservation of the highest possible quality of fruit products obtained after processing. Attention has been drawn to Aronia fruits due to numerous health promoting properties of their products. However, processing of Aronia, like other berries, leads to difficulties that stem from the preparation process, as well as changes in the composition of bioactive compounds. Consequently, in this study, Aronia commercial juice was subjected to different drying techniques: spray drying, freeze drying and vacuum drying with the temperature range of 40-80 °C. All powders obtained had a high content of total polyphenols. Powders gained by spray drying had the highest values which corresponded to a high content of total flavonoids, total monomeric anthocyanins, cyaniding-3-glucoside and total proanthocyanidins. Analysis of the results exhibited a correlation between selected bioactive compounds and their antioxidant capacity. In conclusion, drying techniques have an impact on selected quality parameters, and different drying techniques cause changes in the content of bioactives analysed. Spray drying can be recommended for preservation of bioactives in Aronia products. Powder quality depends mainly on the process applied and parameters chosen. Therefore, Aronia powders production should be adapted to the requirements and design of the final product. Copyright © 2013 Elsevier Ltd. All rights reserved.

[Analysis of variation of monoterpene glycosides and polyhydroxy compounds in paeoniae radix alba during preliminary processing].

PubMed

Xu, Yuan; Liu, Pei; Yan, Hui; Qian, Da-Wei; Duan, Jin-Ao

2014-05-01

To investigate variation of monoterpene glycosides and polyhydroxy compounds in Paeoniae Radix Alba dried by different processing methods. The crude drugs were processed sequentially as washed, removed the head, tail, fine roots and dried. The samples were divided into eight groups by whether peeled and decocted or not. Each group was dried by 35, 45, 60, 80,100, 120 degrees C, sun-dried and shade-dried. HPLC-PDA method was adopted to determine the content of monoterpene glycosides compounds (paeoniflorin alibiflorin, oxypaeoniflorin and benzoylpaeoniflorin), polyhydroxy compounds (catechin and gallic acid) and benzoic acid. Chromatographic conditions: Phecad C18 column (250 mm x 4.6 mm, 5 microm). A principal component analysis (PCA) method was used subsequently to get data processed. The retained content of seven constituents decreased in those peeled crude drug, and after cooked, monoterpene glycosides and polyhydroxy compounds increased while the benzoic acid decreased. It was believed that rele- vant enzymes were inactivated while being cooked so that drying temperature showed little influence on the biotransformation. Contents of effective ingredients in Paeoniae Radix Alba are influenced by drying processing. The preferable method shows to be that crude drug should be cooked before being peeled and dried. As a matter of processing convtence, it is suggested to be peeled and sliced before being dried.

Spectroscopic analysis of seasonal changes in live fuel moisture content and leaf dry mass

Treesearch

Yi Qi; Philip E. Dennison; W. Matt Jolly; Rachael C. Kropp; Simon C. Brewer

2014-01-01

Live fuel moisture content (LFMC), the ratio of water mass to dry mass contained in live plant material, is an important fuel property for determining fire danger and for modeling fire behavior. Remote sensing estimation of LFMC often relies on an assumption of changing water and stable dry mass over time. Fundamental understanding of seasonal variation in plant water...

Relationship between longitudinal stress wave transit time and moisture content of lumber during kiln-drying

Treesearch

William T. Simpson; Xiping. Wang

2001-01-01

The relationship between longitudinal stress wave transit time and wood moisture content (MC) was examined as a potential means of estimating MC control points in dry kiln schedules for lumber. A linear relationship was found between the relative transit time and the average MC of sugar maple and ponderosa pine boards dried according to typical kiln schedules.

Determination of the ascorbic acid content of two medicinal plants in Nigeria.

PubMed

H A, Okeri; P O, Alonge

2006-01-01

The fresh and dried leaves of two edible plants, Oldenlandia corymbosa and Dissotis rotundifolia have been assayed for their ascorbic acid content. They were found to be rich sources of ascorbic acid (vitamin C) when compared with some common garden fruits and vegetables. Students' t-test statistical analysis using INSTAT.EXE program for the results (mean+/-SEM) shows that there was no significant difference for the fresh leaves of the individual plants and also there is no significant difference for the dried leaves (P=0.05). However, there was significant difference between ascorbic acid content of the fresh and dried leaves of the same plant, obviously indicating that the fresh leaves contain more ascorbic acid than the dried leaves.

Frequency, moisture content, and temperature dependent dielectric properties of potato starch related to drying with radio-frequency/microwave energy.

PubMed

Zhu, Zhuozhuo; Guo, Wenchuan

2017-08-24

To develop advanced drying methods using radio-frequency (RF) or microwave (MW) energy, dielectric properties of potato starch were determined using an open-ended coaxial-line probe and network analyzer at frequencies between 20 and 4,500 MHz, moisture contents between 15.1% and 43.1% wet basis (w.b.), and temperatures between 25 and 75 °C. The results showed that both dielectric constant (ε') and loss factor (ε″) were dependent on frequency, moisture content, and temperature. ε' decreased with increasing frequency at a given moisture content or temperature. At low moisture contents (≤25.4% w.b.) or low temperatures (≤45 °C), ε″ increased with increasing frequency. However, ε″ changed from decrease to increase with increasing frequency at high moisture contents or temperatures. At low temperatures (25-35 °C), both ε' and ε″ increased with increasing moisture content. At low moisture contents (15.1-19.5% w.b.), they increased with increasing temperature. The change trends of ε' and ε″ were different and dependent on temperature and moisture content at their high levels. The penetration depth (d p ) decreased with increasing frequency. RF treatments may provide potential large-scale industrial drying application for potato starch. This research offers useful information on dielectric properties of potato starch related to drying with electromagnetic energy.

Effects of Different Drying Methods and Storage Time on Free Radical Scavenging Activity and Total Phenolic Content of Cosmos Caudatus.

PubMed

Mediani, Ahmed; Abas, Faridah; Tan, Chin Ping; Khatib, Alfi

2014-05-07

The present study was conducted to determine the effect of air (AD), oven (OD) and freeze drying (FD) on the free radical scavenging activity and total phenolic content (TPC) of Cosmos caudatus and the effect of storage time by the comparison with a fresh sample (FS). Among the three drying methods that were used, AD resulted in the highest free radical scavenging activity against 1,1-diphenyl-2-picrylhydrazyl (DPPH) (IC50 = 0.0223 mg/mL) and total phenolic content (27.4 g GAE/100 g), whereas OD produced the lowest scavenging activity and TPC value. After three months of storage, the dried samples showed a high and consistent free radical scavenging activity when compared to stored fresh material. The drying methods could preserve the quality of C. caudatus during storage and the stability of its bioactive components can be maintained.

Effects of Different Drying Methods and Storage Time on Free Radical Scavenging Activity and Total Phenolic Content of Cosmos caudatus

PubMed Central

Mediani, Ahmed; Abas, Faridah; Tan, Chin Ping; Khatib, Alfi

2014-01-01

The present study was conducted to determine the effect of air (AD), oven (OD) and freeze drying (FD) on the free radical scavenging activity and total phenolic content (TPC) of Cosmos caudatus and the effect of storage time by the comparison with a fresh sample (FS). Among the three drying methods that were used, AD resulted in the highest free radical scavenging activity against 1,1-diphenyl-2-picrylhydrazyl (DPPH) (IC50 = 0.0223 mg/mL) and total phenolic content (27.4 g GAE/100 g), whereas OD produced the lowest scavenging activity and TPC value. After three months of storage, the dried samples showed a high and consistent free radical scavenging activity when compared to stored fresh material. The drying methods could preserve the quality of C. caudatus during storage and the stability of its bioactive components can be maintained. PMID:26784876

Influence of drying treatments on antioxidant capacity of forage legume leaves.

PubMed

Sang, Saw Yei; Jamharee, Fazrina; Prasad, K Nagendra; Azlan, Azrina; Maliki, Nurzillah

2014-05-01

This study was aimed to investigate the antioxidant capacities of four common forage legume leaves namely, Arachis pintoi (Pintoi), Calapogonium mucunoides (Calapo), Centrosema pubescens (Centro), and Stylosanthes guanensis (Stylo). Two different drying methods (oven-drying and freeze-drying) were employed and antioxidant activities were determined by DPPH, Ferric Reducing Antioxidant Power (FRAP) and β-carotene bleaching assays. Total phenolic content (TPC) was determined using Folin-Ciocalteu assay. Freeze-dried extract showed the highest antioxidant activities by DPPH (EC50 values 1.17-2.13 mg/ml), FRAP (147.08-246.42 μM of Fe(2+)/g), and β-carotene bleaching (57.11-78.60%) compared to oven drying. Hence, freeze drying treatment could be considered useful in retention of antioxidant activity and phenolic content.

The potential of computer vision, optical backscattering parameters and artificial neural network modelling in monitoring the shrinkage of sweet potato (Ipomoea batatas L.) during drying.

PubMed

Onwude, Daniel I; Hashim, Norhashila; Abdan, Khalina; Janius, Rimfiel; Chen, Guangnan

2018-03-01

Drying is a method used to preserve agricultural crops. During the drying of products with high moisture content, structural changes in shape, volume, area, density and porosity occur. These changes could affect the final quality of dried product and also the effective design of drying equipment. Therefore, this study investigated a novel approach in monitoring and predicting the shrinkage of sweet potato during drying. Drying experiments were conducted at temperatures of 50-70 °C and samples thicknesses of 2-6 mm. The volume and surface area obtained from camera vision, and the perimeter and illuminated area from backscattered optical images were analysed and used to evaluate the shrinkage of sweet potato during drying. The relationship between dimensionless moisture content and shrinkage of sweet potato in terms of volume, surface area, perimeter and illuminated area was found to be linearly correlated. The results also demonstrated that the shrinkage of sweet potato based on computer vision and backscattered optical parameters is affected by the product thickness, drying temperature and drying time. A multilayer perceptron (MLP) artificial neural network with input layer containing three cells, two hidden layers (18 neurons), and five cells for output layer, was used to develop a model that can monitor, control and predict the shrinkage parameters and moisture content of sweet potato slices under different drying conditions. The developed ANN model satisfactorily predicted the shrinkage and dimensionless moisture content of sweet potato with correlation coefficient greater than 0.95. Combined computer vision, laser light backscattering imaging and artificial neural network can be used as a non-destructive, rapid and easily adaptable technique for in-line monitoring, predicting and controlling the shrinkage and moisture changes of food and agricultural crops during drying. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Novel method for enumeration of viable Lactobacillus plantarum WCFS1 cells after single-droplet drying.

PubMed

Perdana, Jimmy; Bereschenko, Ludmila; Roghair, Mark; Fox, Martijn B; Boom, Remko M; Kleerebezem, Michiel; Schutyser, Maarten A I

2012-11-01

Survival of probiotic bacteria during drying is not trivial. Survival percentages are very specific for each probiotic strain and can be improved by careful selection of drying conditions and proper drying carrier formulation. An experimental approach is presented, comprising a single-droplet drying method and a subsequent novel screening methodology, to assess the microbial viability within single particles. The drying method involves the drying of a single droplet deposited on a flat, hydrophobic surface under well-defined drying conditions and carrier formulations. Semidried or dried particles were subjected to rehydration, fluorescence staining, and live/dead enumeration using fluorescence microscopy. The novel screening methodology provided accurate survival percentages in line with conventional plating enumeration and was evaluated in single-droplet drying experiments with Lactobacillus plantarum WCFS1 as a model probiotic strain. Parameters such as bulk air temperatures and the carrier matrices (glucose, trehalose, and maltodextrin DE 6) were varied. Following the experimental approach, the influence on the viability as a function of the drying history could be monitored. Finally, the applicability of the novel viability assessment was demonstrated for samples obtained from drying experiments at a larger scale.

Novel Method for Enumeration of Viable Lactobacillus plantarum WCFS1 Cells after Single-Droplet Drying

PubMed Central

Perdana, Jimmy; Bereschenko, Ludmila; Roghair, Mark; Fox, Martijn B.; Boom, Remko M.; Kleerebezem, Michiel

2012-01-01

Survival of probiotic bacteria during drying is not trivial. Survival percentages are very specific for each probiotic strain and can be improved by careful selection of drying conditions and proper drying carrier formulation. An experimental approach is presented, comprising a single-droplet drying method and a subsequent novel screening methodology, to assess the microbial viability within single particles. The drying method involves the drying of a single droplet deposited on a flat, hydrophobic surface under well-defined drying conditions and carrier formulations. Semidried or dried particles were subjected to rehydration, fluorescence staining, and live/dead enumeration using fluorescence microscopy. The novel screening methodology provided accurate survival percentages in line with conventional plating enumeration and was evaluated in single-droplet drying experiments with Lactobacillus plantarum WCFS1 as a model probiotic strain. Parameters such as bulk air temperatures and the carrier matrices (glucose, trehalose, and maltodextrin DE 6) were varied. Following the experimental approach, the influence on the viability as a function of the drying history could be monitored. Finally, the applicability of the novel viability assessment was demonstrated for samples obtained from drying experiments at a larger scale. PMID:22983965

Publications - GMC 291 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 291 Publication Details Title: Geologic log of and measured air-dry gas content desorption Reference State of Alaska, and Seamount, D.T., 2000, Geologic log of and measured air-dry gas content

Study on biogenic amines in various dry salted fish consumed in China

NASA Astrophysics Data System (ADS)

Wu, Yanyan; Chen, Yufeng; Li, Laihao; Yang, Xianqing; Yang, Shaoling; Lin, Wanling; Zhao, Yongqiang; Deng, Jianchao

2016-08-01

This study was carried out to investigate the biogenic amines (BAs), physicochemical property and microorganisms in dry salted fish, a traditional aquatic food consumed in China. Forty three samples of dry salted fish were gathered from retail and wholesale markets and manufacturers, which had been produced in various regions in China. Cadaverine (CAD) and putrescine (PUT) were quantitatively the most common biogenic amines. About 14% of the samples exceeded the histamine content standards established by the FDA and/or EU. The highest histamine content was found in Silver pomfret ( Pampus argenteus) (347.79 mg kg-1). Five of forty three samples exceeded the acceptable content of TYR (100 mg kg-1), and 23.26% of dried-salted fish contained high contents of biogenic amines (above 600 mg kg-1). In addition, species, regions, pickling processes and drying methods made the physicochemical property, microorganisms and biogenic amines in dry salted fish to be different to some extents. The total plate count (TPC) was much higher than that of total halophilic bacteria in all samples. The biogenic amines, physicochemical property and microbiological counts exhibited large variations among samples. Furthermore, no significant correlation between biogenic amines and physicochemical property and TPC was observed. This study indicated that dry salted fish may still present healthy risk for BAs, depending on the processing methods, storage conditions among others.

Comparison of Selected Metals Content in Cambodian Striped Snakehead Fish (Channa striata) Using Solar Drying System and Open Sun Drying

PubMed Central

Abu Bakar, Nur Faizah; Fudholi, Ahmad; Ruslan, Mohd Hafidz; Saroeun, Im

2015-01-01

The content of 12 elements in Cambodian dried striped snakehead fish was determined using inductively coupled plasma mass spectrometry. The present study compares the level of the trace toxic metals and nutritional trace elements in the fish processed using solar drying system (SDS) and open sun drying (OSD). The skin of SDS fish has lower level of As, Pb, and Cd compared to the OSD sample. As such, the flesh of the fish accumulated higher amount of toxic metals during OSD compared to SDS. However, arsenic was detected in both samples within the safe limit. The nutritional elements (Fe, Mn, Mg, Se, Mo, Cu, Ni, and Cr) were higher in the skin sample SDS fish compared to OSD fish. These beneficial metals were not accumulated in the flesh sample SDS fish demonstrating lower level compared to drying under conventional system. The reddish coloration of the SDS fish was due to the presence of high Cu content in both the skin and flesh samples which possibly account for no mold formation 5 days after packaging. As conclusion, drying of Cambodian C. striata using solar-assisted system has proven higher content of the nutritious elements compared to using the conventional system despite only slight difference in the toxic metals level between the two systems. PMID:25688274

Scalable organic solvent free supercritical fluid spray drying process for producing dry protein formulations.

PubMed

Nuchuchua, O; Every, H A; Hofland, G W; Jiskoot, W

2014-11-01

In this study, we evaluated the influence of supercritical carbon dioxide (scCO2) spray drying conditions, in the absence of organic solvent, on the ability to produce dry protein/trehalose formulations at 1:10 and 1:4 (w/w) ratios. When using a 4L drying vessel, we found that decreasing the solution flow rate and solution volume, or increasing the scCO2 flow rate resulted in a significant reduction in the residual water content in dried products (Karl Fischer titration). The best conditions were then used to evaluate the ability to scale the scCO2 spray drying process from 4L to 10L chamber. The ratio of scCO2 and solution flow rate was kept constant. The products on both scales exhibited similar residual moisture contents, particle morphologies (SEM), and glass transition temperatures (DSC). After reconstitution, the lysozyme activity (enzymatic assay) and structure (circular dichroism, HP-SEC) were fully preserved, but the sub-visible particle content was slightly increased (flow imaging microscopy, nanoparticle tracking analysis). Furthermore, the drying condition was applicable to other proteins resulting in products of similar quality as the lysozyme formulations. In conclusion, we established scCO2 spray drying processing conditions for protein formulations without an organic solvent that holds promise for the industrial production of dry protein formulations. Copyright © 2014 Elsevier B.V. All rights reserved.

Seasonal and air mass trajectory effects on dissolved organic matter of bulk deposition at a coastal town in south-western Europe.

PubMed

Santos, Patrícia S M; Santos, Eduarda B H; Duarte, Armando C

2013-01-01

Rainwater contains a complex mixture of organic compounds which may influence climate, terrestrial and maritime ecosystems and thus human health. In this work, the characteristics of DOM of bulk deposition at a coastal town on the southwest of Europe were assessed by UV-visible and three-dimensional excitation-emission matrix fluorescence spectroscopies and by dissolved organic carbon (DOC) content. The seasonal and air mass trajectory effects on dissolved organic matter (DOM) of bulk deposition were evaluated. The absorbance at 250 nm (UV(250 nm)) and integrated fluorescence showed to be positively correlated with each other, and they were also positively correlated to the DOC in bulk deposition, which suggest that a constant fraction of DOM is likely to fluoresce. There was more chromophoric dissolved organic matter (CDOM) present in summer and autumn seasons than in winter and spring. Bulk deposition associated with terrestrial air masses contained a higher CDOM content than bulk deposition related to marine air masses, thus highlighting the contribution of terrestrial/anthropogenic sources.

Bulk Leisure--Problem or Blessing?

ERIC Educational Resources Information Center

Beland, Robert M.

1983-01-01

With an increasing number of the nation's work force experiencing "bulk leisure" time because of new work scheduling procedures, parks and recreation offices are encouraged to examine their program scheduling and content. (JM)

Sliding Wear Characteristics and Corrosion Behaviour of Selective Laser Melted 316L Stainless Steel

NASA Astrophysics Data System (ADS)

Sun, Y.; Moroz, A.; Alrbaey, K.

2014-02-01

Stainless steel is one of the most popular materials used for selective laser melting (SLM) processing to produce nearly fully dense components from 3D CAD models. The tribological and corrosion properties of stainless steel components are important in many engineering applications. In this work, the wear behaviour of SLM 316L stainless steel was investigated under dry sliding conditions, and the corrosion properties were measured electrochemically in a chloride containing solution. The results show that as compared to the standard bulk 316L steel, the SLM 316L steel exhibits deteriorated dry sliding wear resistance. The wear rate of SLM steel is dependent on the vol.% porosity in the steel and by obtaining full density it is possible achieve wear resistance similar to that of the standard bulk 316L steel. In the tested chloride containing solution, the general corrosion behaviour of the SLM steel is similar to that of the standard bulk 316L steel, but the SLM steel suffers from a reduced breakdown potential and is more susceptible to pitting corrosion. Efforts have been made to correlate the obtained results with porosity in the SLM steel.

Proton Content and Nature in Perovskite Ceramic Membranes for Medium Temperature Fuel Cells and Electrolysers

PubMed Central

Colomban, Philippe; Zaafrani, Oumaya; Slodczyk, Aneta

2012-01-01

Recent interest in environmentally friendly technology has promoted research on green house gas-free devices such as water steam electrolyzers, fuel cells and CO2/syngas converters. In such applications, proton conducting perovskite ceramics appear especially promising as electrolyte membranes. Prior to a successful industrial application, it is necessary to determine/understand their complex physical and chemical behavior, especially that related to proton incorporation mechanism, content and nature of bulk protonic species. Based on the results of quasi-elastic neutron scattering (QNS), thermogravimetric analysis (TGA), Raman and IR measurements we will show the complexity of the protonation process and the importance of differentiation between the protonic species adsorbed on a membrane surface and the bulk protons. The bulk proton content is very low, with a doping limit (~1–5 × 10−3 mole/mole), but sufficient to guarantee proton conduction below 600 °C. The bulk protons posses an ionic, covalent bond free nature and may occupy an interstitial site in the host perovskite structure. PMID:24958293

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawrence, G.B.; Fernandez, I.J.; Goltz, S.M.

To provide information needed to assess the current and future status of spruce-fir forests in Maine, the Howland Integrated Forest Study (HIFS) was initiated in 1987 as part of the USDA Forest Service Forest Response Program, in conjunction with the establishment of a Mountain Cloud Chemistry Program (MCCP) monitoring site. Through this project, bulk and wet-only precipitation, dry deposition, throughfall and soil solution chemistry has been determined. This paper will focus on soil solution collected between May, 1988 and bulk precipitation collected from June through November, 1988.

Increases in the longevity of desiccation-phase developing rice seeds: response to high-temperature drying depends on harvest moisture content

PubMed Central

Whitehouse, K. J.; Hay, F. R.; Ellis, R. H.

2015-01-01

Background and Aims Previous studies have suggested that the drying conditions routinely used by genebanks may not be optimal for subsequent seed longevity. The aim of this study was to compare the effect of hot-air drying and low-temperature drying on subsequent seed longevity for 20 diverse rice accessions and to consider how factors related to seed production history might influence the results. Methods Seeds of rice, Oryza sativa, were produced according to normal regeneration procedures at IRRI. They were harvested at different times [harvest date and days after anthesis (DAA), once for each accession] and dried either in a drying room (DR; 15 % relative humidity, 15 °C) or in a flat-bed heated-air batch dryer (BD; 45 °C, 8 h d–1) for up to six daily cycles followed by drying in the DR. Relative longevity was assessed by storage at 10·9 % moisture content and 45 °C. Key Results Initial drying in the BD resulted in significantly greater longevity compared with the DR for 14 accessions (seed lots): the period of time for viability to fall to 50 % for seeds dried in the BD as a percentage of that for seeds dried throughout in the DR varied between 1.3 and 372·2 % for these accessions. The seed lots that responded the most were those that were harvested earlier in the season and at higher moisture content. Drying in the BD did not reduce subsequent longevity compared with DR drying for any of the remaining accessions. Conclusions Seeds harvested at a moisture content where, according to the moisture desorption isotherm, they could still be metabolically active (>16·2 %) may be in the first stage of the post-mass maturity, desiccation phase of seed development and thus able to increase longevity in response to hot-air drying. The genebank standards regarding seed drying for rice and, perhaps, for other tropical species should therefore be reconsidered. PMID:26133688

Increases in the longevity of desiccation-phase developing rice seeds: response to high-temperature drying depends on harvest moisture content.

PubMed

Whitehouse, K J; Hay, F R; Ellis, R H

2015-08-01

Previous studies have suggested that the drying conditions routinely used by genebanks may not be optimal for subsequent seed longevity. The aim of this study was to compare the effect of hot-air drying and low-temperature drying on subsequent seed longevity for 20 diverse rice accessions and to consider how factors related to seed production history might influence the results. Seeds of rice, Oryza sativa, were produced according to normal regeneration procedures at IRRI. They were harvested at different times [harvest date and days after anthesis (DAA), once for each accession] and dried either in a drying room (DR; 15 % relative humidity, 15 °C) or in a flat-bed heated-air batch dryer (BD; 45 °C, 8 h d(-1)) for up to six daily cycles followed by drying in the DR. Relative longevity was assessed by storage at 10·9 % moisture content and 45 °C. Initial drying in the BD resulted in significantly greater longevity compared with the DR for 14 accessions (seed lots): the period of time for viability to fall to 50 % for seeds dried in the BD as a percentage of that for seeds dried throughout in the DR varied between 1.3 and 372·2 % for these accessions. The seed lots that responded the most were those that were harvested earlier in the season and at higher moisture content. Drying in the BD did not reduce subsequent longevity compared with DR drying for any of the remaining accessions. Seeds harvested at a moisture content where, according to the moisture desorption isotherm, they could still be metabolically active (>16·2 %) may be in the first stage of the post-mass maturity, desiccation phase of seed development and thus able to increase longevity in response to hot-air drying. The genebank standards regarding seed drying for rice and, perhaps, for other tropical species should therefore be reconsidered. © The Author 2015. Published by Oxford University Press on behalf of the Annals of Botany Company.

Physical-chemical quality of onion analyzed under drying temperature

NASA Astrophysics Data System (ADS)

Djaeni, M.; Arifin, U. F.; Sasongko, S. B.

2017-03-01

Drying is one of conventional processes to enhance shelf life of onion. However, the active compounds such as vitamin and anthocyanin (represented in red color), degraded due to the introduction of heat during the process. The objective of this research was to evaluate thiamine content as well as color in onion drying under different temperature. As an indicator, the thiamine and color was observed every 30 minutes for 2 hours. Results showed that thiamine content and color were sensitvely influenced by the temperature change. For example, at 50°C for 2 hours drying process, the thiamine degradation was 55.37 %, whereas, at 60°C with same drying time, the degradation was 74.01%. The quality degradation also increased by prolonging drying time.

Effect of drying methods (microwave vacuum, freeze, hot air and sun drying) on physical, chemical and nutritional attributes of five pepper (Capsicum annuum var. annuum) cultivars.

PubMed

Maurya, Vaibhav Kumar; Gothandam, Kodiveri Muthukaliannan; Ranjan, Vijay; Shakya, Amita; Pareek, Sunil

2018-07-01

A randomized block design experiment was performed to investigate the influence of drying on the physical, chemical and nutritional quality attributes of five prominent cultivars of India under sun drying (SD) (mean temperature 35.5 °C, average daily radiation 5.26 kW h m -2 and mean relative humidity 73.66% RH), hot air drying (HD) at 65 °C, microwave vacuum drying (MVD) (800 W, 5 kPa) and freeze drying (FD) (-50 °C, 5 kPa). Water activity, pH, total phenolic content (TPC), ascorbic acid (AA), capsaicin, β-carotene, color and Scoville heat unit were studied. TPC, AA, capsaicin content, β-carotene, color and water activity were significantly affected by the drying method. FD was observed to be most efficient in minimizing the loss of color, capsaicin and β-carotene. The hotness of analyzed samples decreased in the order 'Bird's Eye' > 'Sannam S4' > 'CO-4' > 'PLR-1' > 'PKM-1' among the studied cultivars, and FD > MVD > HD > SD among the drying methods. The FD method was observed to be the most efficient drying method for retaining capsaicin content over other drying methods (SD, HD, MVD), whereas MVD was found to be most efficient in minimizing the loss to nutritional attributes for all five pepper cultivars. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Nutritional quality and amino acid composition of diets consumed by scavenging hens and cocks across seasons.

PubMed

Ncobela, Cyprial Ndumiso; Chimonyo, Michael

2016-04-01

The objective of the study was to determine the effect of season on nutritional quality and amino acid composition of diets that scavenging hens and cocks consume. Thirty hens and 30 cocks were purchased and slaughtered during each of the rainy, post rainy, cool dry and hot dry seasons. A total of 240 birds were used in the study. Fresh crop content weights were high (P < 0.05) during the cool dry season. Cereal grains, kitchen wastes, green materials, animal protein sources and inorganic materials were the main components of the crop contents. Crop contents varied with season and sex of bird (P < 0.05). The cereal grain weights were high during cool dry and hot dry seasons. Weights of animal protein sources (insects, locusts and termites) were higher (P < 0.05) during the rainy and post rainy seasons. Hens contained more animal protein sources (P < 0.05) than cocks. Hens had a higher (P < 0.05) lysine content during the rainy season than cocks. Histidine, serine, arginine, threonine, cysteine and lysine contents varied with seasons (P < 0.05). Methionine did not vary with season and sex of the bird. Nutritional supplementation of village chickens should, therefore, vary with seasons.

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer... dryer” AND you have a record of the inlet moisture content and inlet dryer temperature (as required in... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer... dryer” AND you have a record of the inlet moisture content and inlet dryer temperature (as required in... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

The effect of clothing care activities on textile formaldehyde content.

PubMed

Novick, Rachel M; Nelson, Mindy L; McKinley, Meg A; Anderson, Grace L; Keenan, James J

2013-01-01

Textiles are commonly treated with formaldehyde-based residues that may potentially induce allergic contact dermatitis in sensitive individuals. This study examined the initial formaldehyde content in clothing and resulting changes due to care activities. Twenty clothing articles were examined and 17 of them did not have detectable levels of formaldehyde. One shirt contained a formaldehyde concentration of 3172 ppm, and two pairs of pants had formaldehyde concentrations of 1391 ppm and 86 ppm. The two highest results represent formaldehyde levels that are up to 40-fold greater than international textile regulations. The two items with the greatest formaldehyde content were washed and dried in a manner similar to that used by consumers, including hand and machine washing in hot or cold water followed by air or machine drying. The washing and drying procedures reduced formaldehyde levels to between 26 and 72% of untreated controls. Differences in the temperature or type of washing and drying did not result in a clear trend in the subsequent formaldehyde content. In addition, samples were hot ironed, which did not affect the formaldehyde content as significantly. Understanding the formaldehyde content in clothing and its potential reduction through care activities may be useful for manufacturers and formaldehyde-sensitive individuals.

Folate content in faba beans (Vicia faba L.)-effects of cultivar, maturity stage, industrial processing, and bioprocessing.

PubMed

Hefni, Mohammed E; Shalaby, Mohamed T; Witthöft, Cornelia M

2015-01-01

Faba beans are an important source of folate and commonly consumed in Egypt. This study examined the effects of Egyptian industrial food processing (e.g., canning and freezing), germination, cultivar, and maturity stages on folate content, with the aim to develop a candidate functional canned faba bean food with increased folate content. The folate content in four cultivars of green faba beans ranged from 110 to 130 μg 100 g(-1) fresh weight (535-620 μg 100 g(-1) dry matter [DM]), which was four- to sixfold higher than in dried seeds. Industrial canning of dried seeds resulted in significant folate losses of ∼20% (P = 0.004), while industrial freezing had no effect. Germination of faba beans increased the folate content by >40% (P < 0.0001). A novel industrial canning process involving pregermination of dried faba beans resulted in a net folate content of 194 μg 100 g(-1) DM, which is 52% more than in conventional canned beans. The consumption of green faba beans should be recommended, providing ∼120 μg dietary folate equivalents per 100 g/portion.

Letter to the editor: Critical assessments of the current state of scientific knowledge, terminology, and research needs concerning the ecological effects of elevated atmospheric nitrogen deposition in China

NASA Astrophysics Data System (ADS)

Pan, Yuepeng; Liu, Yongwen; Wentworth, Gregory R.; Zhang, Lin; Zhao, Yuanhong; Li, Yi; Liu, Xuejun; Du, Enzai; Fang, Yunting; Xiao, Hongwei; Ma, Hongyuan; Wang, Yuesi

2017-03-01

In a publication in Atmospheric Environment (http://dx.doi.org/10.1016/j.atmosenv.2015.10.081), Gu et al. (2015) estimated that "the total nitrogen (N) deposition in 2010 was 2.32 g N m-2 yr-1" in China. This value is comparable with previous estimations based on a synthesized dataset of wet/bulk inorganic N deposition observations, which underestimates the total N deposition since their algorithm (equations (2) and (3) in their paper) does not account for dry deposition of NH3, HNO3, NOx and wet/dry deposition of HONO and organic nitrogen (e.g. amines, amides, PAN). Indeed, Gu et al. (2015) mixed the terminology of wet/bulk deposition and total deposition. Another flawed assumption by Gu et al. (2015) is that all inorganic N in precipitation estimated by their algorithm originates from fertilizer and coal combustion. This is incorrect and almost certainly causes biases in the spatial and temporal distribution of estimated wet/bulk inorganic N deposition (Fig. 5 in their paper), further considering the fact that they neglected important N sources like livestock and they did not consider the nonlinearity between various sources and deposition. Besides the input data on N deposition, the model validation (Sect. 2.3.2) described in their paper also requires clarification because the detailed validation information about the time series of observational dataset versus modeling results was not given. As a result of these combined uncertainties in their estimation of N deposition and the lack of detail for model-measurement comparison, their estimates of the impacts of N deposition on carbon storage in Chinese forests may need further improvement. We suggest the clarification of the terminology regarding N deposition, especially for wet deposition, bulk deposition, gaseous and particulate dry deposition or total deposition since the accurate distinction between these terms is crucial to investigating and estimating the effects of N deposition on ecosystems.

Curcuminoid content of Curcuma longa L. and Curcuma xanthorrhiza rhizome based on drying method with NMR and HPLC-UVD

NASA Astrophysics Data System (ADS)

Hadi, S.; Artanti, A. N.; Rinanto, Y.; Wahyuni, D. S. C.

2018-04-01

Curcuminoid, consisting of curcumin, demethoxycurcumin and bis demethoxycurcumin, is the major compound in Curcuma longa L. and Curcuma xanthorrhiza rhizome. It has been known to have a potent antioxidants, anticancer, antibacteria activity. Those rhizomes needs to be dried beforehand which influenced the active compounds concentration. The present work was conducted to assess the curcuminoid content of C. longa L. and C. xanthorrhiza based on drying method with Nuclear Magnetic Resonance (NMR) and High Pressure Liquid Chromatography (HPLC)-UVD. Samples were collected and dried using freeze-drying and oven method. The latter is the common method applied in most drying method at herbal medicine preparation procedure. All samples were extracted using 96% ethanol and analyzed using NMR and HPLC-UVD. Curcuminoid as a bioactive compound in the sample exhibited no significant difference and weak significant difference in C. xanthorrhiza and C. longa L., respectively. HLPC-UVD as a reliable analytical method for the quantification is subsequently used to confirm of the data obtained by NMR. It resulted that curcuminoid content showed no significant difference in both samples. This replied that curcuminoids content in both samples were stable into heating process. These results are useful information for simplicia standardization method in pharmaceutical products regarding to preparation procedure.

[Influence of different original processing methods on quality of Salvia Miltiorrhizae Radix et Rhizoma from Shandong].

PubMed

Zhao, Zhi-Gang; Gao, Shu-Rui; Hou, Jun-Ling; Wang, Wen-Quan; Xu, Zhen-Guang; Song, Yan; Zhang, Xian-Ming; Li, Jun

2014-04-01

In this paper the contents of rosmarinic acid, salvianolic acid B, crytotanshinone, tanshinone II(A) in samples of different original processed Salvia Miltiorrhizae Radix et Rhizoma were determined by HPLC. Different processing methods have varied influences on four active ingredients in Salvia Miltiorrhizae Radix et Rhizoma. Sun-drying reduced the content of crytotanshinone, tanshi-none II(A) and rosmarinic acid, integralsamples were better than those cut into segments. Oven dry method had great influence on water--soluble ingredients, high temperature (80-100 degrees C) could easily cause big loss of rosmarinic acid and salvianolic acid B. The role of traditional processing method "fahan: was complicated, the content of rosmarinic acid decreased, crytotanshinone and tanshinone II(A) increased, and salvianolic acid B showed no difference after "fahan". Drying in the shade and oven dry under low temperatrure (40-60 degrees C) were all effective to keep active ingredients of Salvia Miltiorrhizae Radix et Rhizoma, and, there was no difference between integral samples and samples cut into segments. Therefore, considering comprehensively the content of active ingredients in Salvia Miltiorrhizae Radix et Rhizoma, and processing costing etc., shade-drying or oven dry underlow temperature (40-60 degrees C) should be the most suitable original processing method.

Publishing and Revising Content

EPA Pesticide Factsheets

Editors and Webmasters can publish content without going through a workflow. Publishing times and dates can be set, and multiple pages can be published in bulk. Making an edit to published content created a revision.

Resistant starch content among several sorghum (Sorghum bicolor) genotypes and the effect of heat treatment on resistant starch retention in two genotypes.

PubMed

Teixeira, Natália de Carvalho; Queiroz, Valéria Aparecida Vieira; Rocha, Maria Clara; Amorim, Aline Cristina Pinheiro; Soares, Thayana Oliveira; Monteiro, Marlene Azevedo Magalhães; de Menezes, Cícero Beserra; Schaffert, Robert Eugene; Garcia, Maria Aparecida Vieira Teixeira; Junqueira, Roberto Gonçalves

2016-04-15

The resistant starch (RS) contents in 49 sorghum genotypes and the effects of heat treatment using dry and wet heat on the grain and flour from two sorghum genotypes were investigated. The results showed a wide variation in the RS contents of the genotypes analyzed. The RS mean values were grouped into six distinct groups and ranged from 0.31±0.33 g/100 g to 65.66±5.46 g/100 g sorghum flour on dry basis. Dry heat causes minor losses in the RS content with retentions of up to 97.19±1.92% of this compound, whereas wet heat retained at most 6.98±0.43% of the RS. The SC 59 and (SSN76)FC6608 RED KAFIR BAZINE (ASA N23) cultivars, which have an average RS content of 65.51 g/100 g, were appropriate for human consumption, and the use of dry heat is presented as a better alternative for the preservation of RS in heat-treated grains. Copyright © 2015 Elsevier Ltd. All rights reserved.

High humidity hot air impingement blanching (HHAIB) enhances drying rate and softens texture of apricot via cell wall pectin polysaccharides degradation and ultrastructure modification.

PubMed

Deng, Li-Zhen; Mujumdar, A S; Yang, Xu-Hai; Wang, Jun; Zhang, Qian; Zheng, Zhi-An; Gao, Zhen-Jiang; Xiao, Hong-Wei

2018-09-30

The effects of high humidity hot air impingement blanching (HHAIB) over a range of application times (30, 60, 90, and 120 s) on drying characteristics, hardness, cell wall pectin fractions contents and nanostructure, as well ultrastructure of apricot were investigated. Results showed that HHAIB reduced drying time and decreased the hardness of apricot by 20.7%-34.5% and 46.57%-71.89%, respectively. The water-soluble pectin (WSP) contents increased after blanching, while the contents of chelate-soluble pectin (CSP) and sodium-carbonate-soluble pectin (NSP) decreased significantly (P < 0.05). The hardness and drying time were found to correlate inversely with the WSP content, but positively with CSP and NSP contents. Atomic force microscopy (AFM) detection showed the decomposition and degradation of pectin fractions during blanching. Additionally, transmission electron microscopy (TEM) observation indicated that the cell wall structure was degraded and middle lamella integrity was destroyed by blanching. Copyright © 2018 Elsevier Ltd. All rights reserved.

Laboratory Evaluation of Remediation Alternatives for U.S. Coast Guard Small Arms Firing Ranges

DTIC Science & Technology

1999-11-01

S) is an immobilization process that involves the mixing of a contaminated soil with a binder material to enhance the physical and chemical...samples were shipped to WES for laboratory analysis. Phase III: Homogenization of the Bulk Samples. Each of the bulk samples was separately mixed to...produce uniform samples for testing. These mixed bulk soil samples were analyzed for metal content. Phase IV: Characterization of the Bulk Soils

Soil strength and macropore volume limit root elongation rates in many UK agricultural soils.

PubMed

Valentine, Tracy A; Hallett, Paul D; Binnie, Kirsty; Young, Mark W; Squire, Geoffrey R; Hawes, Cathy; Bengough, A Glyn

2012-07-01

Simple indicators of crop and cultivar performance across a range of soil types and management are needed for designing and testing sustainable cropping practices. This paper determined the extent to which soil chemical and physical properties, particularly soil strength and pore-size distribution influences root elongation in a wide range of agricultural top soils, using a seedling-based indicator. Intact soil cores were sampled from the topsoil of 59 agricultural fields in Scotland, representing a wide geographic spread, range of textures and management practices. Water release characteristics, dry bulk density and needle penetrometer resistance were measured on three cores from each field. Soil samples from the same locations were sieved, analysed for chemical characteristics, and packed to dry bulk density of 1.0 g cm(-3) to minimize physical constraints. Root elongation rates were determined for barley seedlings planted in both intact field and packed soil cores at a water content close to field capacity (-20 kPa matric potential). Root elongation in field soil was typically less than half of that in packed soils. Penetrometer resistance was typically between 1 and 3 MPa for field soils, indicating the soils were relatively hard, despite their moderately wet condition (compared with <0.2 MPa for packed soil). Root elongation was strongly linked to differences in physical rather than chemical properties. In field soil root elongation was related most closely to the volume of soil pores between 60 µm and 300 µm equivalent diameter, as estimated from water-release characteristics, accounting for 65.7 % of the variation in the elongation rates. Root elongation rate in the majority of field soils was slower than half of the unimpeded (packed) rate. Such major reductions in root elongation rates will decrease rooting volumes and limit crop growth in soils where nutrients and water are scarce.

Holocene glacier activity reconstructed from proglacial lake Gjøavatnet on Amsterdamøya, NW Svalbard

NASA Astrophysics Data System (ADS)

de Wet, Gregory A.; Balascio, Nicholas L.; D'Andrea, William J.; Bakke, Jostein; Bradley, Raymond S.; Perren, Bianca

2018-03-01

Well-dated and highly resolved paleoclimate records from high latitudes allow for a better understanding of past climate change. Lake sediments are excellent archives of environmental change, and can record processes occurring within the catchment, such as the growth or demise of an upstream glacier. Here we present a Holocene-length, multi-proxy lake sediment record from proglacial lake Gjøavatnet on the island of Amsterdamøya, northwest Svalbard. Today, Gjøavatnet receives meltwater from the Annabreen glacier and contains a record of changes in glacier activity linked to regional climate conditions. We measured changes in organic matter content, dry bulk density, bulk carbon isotopes, elemental concentrations via Itrax core-scanning, and diatom community composition to reconstruct variability in glacier extent back through time. Our reconstruction indicates that glacially derived sedimentation in the lake decreased markedly at ∼11.1 cal kyr BP, although a glacier likely persisted in the catchment until ∼8.4 cal kyr BP. During the mid-Holocene (∼8.4-1.0 cal kyr BP) there was significantly limited glacial influence in the catchment and enhanced deposition of organic-rich sediment in the lake. The deposition of organic rich sediments during this time was interrupted by at least three multi-centennial intervals of reduced organic matter accumulation (∼5.9-5.0, 2.7-2.0, and 1.7-1.5 cal kyr BP). Considering our chronological information and a sedimentological comparison with intervals of enhanced glacier input, we interpret these intervals not as glacial advances, but rather as cold/dry episodes that inhibited organic matter production in the lake and surrounding catchment. At ∼1.0 cal kyr BP, input of glacially derived sediment to Gjøavatnet abruptly increased, representing the rapid expansion of the Annabreen glacier.

40 CFR Table 3 to Subpart Dddd of... - Work Practice Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... with a 24-hour block average inlet moisture content of less than or equal to 30 percent (by weight, dry... average inlet moisture content of the veneer is less than or equal to 25 percent (by weight, dry basis...

Spray-dried chitosan as a direct compression tableting excipient.

PubMed

Chinta, Dakshinamurthy Devanga; Graves, Richard A; Pamujula, Sarala; Praetorius, Natalie; Bostanian, Levon A; Mandal, Tarun K

2009-01-01

The objective of this study was to prepare and evaluate a novel spray-dried tableting excipient using a mixture of chitosan and lactose. Three different grades of chitosan (low-, medium-, and high-molecular-weight) were used for this study. Propranolol hydrochloride was used as a model drug. A specific amount of chitosan (1, 1.9, and 2.5 g, respectively) was dissolved in 50 mL of an aqueous solution of citric acid (1%) and later mixed with 50 mL of an aqueous solution containing lactose (20, 19.1, and 18.5 g, respectively) and propanolol (2.2 g). The resultant solution was sprayed through a laboratory spray drier at 1.4 mL/min. The granules were evaluated for bulk density, tap density, Carr index, particle size distribution, surface morphology, thermal properties, and tableting properties. Bulk density of the granules decreased from 0.16 to 0.13 g/mL when the granules were prepared using medium- or high-molecular-weight chitosan compared with the low-molecular-weight chitosan. The relative proportion of chitosan also showed a significant effect on the bulk density. The granules prepared with 1 g of low-molecular-weight chitosan showed the minimum Carr index (11.1%) indicating the best flow properties among all five formulations. All three granules prepared with 1 g chitosan, irrespective of their molecular weight, showed excellent flow properties. Floating tablets prepared by direct compression of these granules with sodium bicarbonate showed 50% drug release between 30 and 35 min. In conclusion, the spray-dried granules prepared with chitosan and lactose showed excellent flow properties and were suitable for tableting.

Optimization of instant powdered chicken feet broth’s drying temperature and time on pilot plant scale production

NASA Astrophysics Data System (ADS)

Hidayati, N.; Widyaningsih, T. D.

2018-03-01

Chicken feet by-product of chicken industries amounted to approximately 65,894 tons/year commonly used as broths. These by-products are potentially produced into an instant form as an anti-inflammatory functional food on industrial scale. Therefore, it is necessary to optimize the critical parameters of the drying process. The aim of this study was to determine the optimum temperature and time of instant powdered chicken feet broth’s drying on pilot plant scale, to find out product’s comparison of the laboratory and pilot plant scale, and to assess financial feasibility of the business plan. The optimization of pilot plant scale’s research prepared and designed with Response Surface Methodology-Central Composite Design. The optimized factors were powdered broth’s drying temperature (55°C, 60°C, 65°C) and time (10 minutes, 11 minutes, 12 minutes) with the response observed were water and chondroitin sulphate content. The optimum condition obtained was drying process with temperature of 60.85°C for 10,05 minutes resulting in 1.90 ± 0.02% moisture content, 32.48 ± 0.28% protein content, 12.05 ± 0.80% fat content, 28.92 ± 0.09 % ash content, 24.64 ± 0.52% carbohydrate content, 1.26 ± 0.05% glucosamine content, 0.99 ± 0.23% chondroitin sulphate content, 50.87 ± 1.00% solubility, 8.59 ± 0.19% water vapour absorption, 0.37% levels of free fatty acid, 13.66 ± 4.49% peroxide number, lightness of 60.33 ± 1.24, yellowness of 3.83 ± 0.26 and redness of 21.77 ± 0.42. Financial analysis concluded that this business project was feasible to run.

The influence of sun drying process and prolonged storage on composition of essential oil from clove buds (Syzygium aromaticum)

NASA Astrophysics Data System (ADS)

Hastuti, L. T.; Saepudin, E.; Cahyana, A. H.; Rahayu, D. U. C.; Murni, V. W.; Haib, J.

2017-07-01

Clove (Syzygium aromaticum) is native to Indonesia and used as a spice in virtually all of the world's cuisine. Clove bud oil, a yellow liquid, is obtained from distillation of buds. The quality of oil is influenced by origin, post-harvest processing, pre-treatment before distillation, the distillation method, and post-distillation treatment. The objective of this study is to investigate the effect of drying process and prolonged storage on essential oil composition of clove bud from the Tolitoli, Indonesia. To determine the effect of drying, fresh clove bud was dried under sunlight until it reached moisture content 13±1 %. The effect of storage was studied in the oil extracted from clove bud that was stored in laboratory at 25 °C for 4 months. The essential oil of each treatment was obtained by steam distillation and its chemical composition was analyzed by GC/MS. The major components found in fresh and dried clove are as follows: eugenol, eugenyl acetate, and caryophyllene. Percentage of caryophyllene was slightly increase after drying but decrease during storage. While the content of eugenyl acetate decreased during drying and storage, the content of eugenol increased. The drying and storage also affect to the change on minor compounds of essential oil of clove.

Potential contribution of mangoes to reduction of vitamin A deficiency in Kenya.

PubMed

Muoki, Penina N; Makokha, Anselimo O; Onyango, Christine A; Ojijo, Nelson K O

2009-01-01

The β-carotene content of fresh and dried mangoes commonly consumed in Kenya was evaluated and converted to retinol equivalent (RE). Mango fruits of varieties Ngowe, Apple, and Tommy Atkins were harvested at mature green, partially ripe, and ripe stages and their β-carotene content analyzed. The stability of β-carotene in sun dried mangoes was also studied over 6 months under usual marketing conditions used in Kenya. The effect of using simple pretreatment methods prior to drying of mango slices on retention of β-carotene was as well evaluated. In amounts acceptable to children and women, fresh and dried mangoes can supply 50% or more of the daily required retinol equivalent for children and women. Stage of ripeness, variety, postharvest holding temperature, method of drying, and storage time of dried mango slices affected β-carotene content and consequently vitamin A value of the fruits. Apple variety grown in Machakos had the highest β-carotene. It exceeded the daily RE requirements by 11.8% and 21.5% for women and children respectively. Fresh or dried mangoes are a significant provitamin A source and should be included in food-based approaches aiming to reduce vitamin A deficiency.

Depositional characteristics of atmospheric polybrominated diphenyl ethers on tree barks

PubMed Central

Chun, Man Young

2014-01-01

Objectives This study was conducted to determine the depositional characteristics of several tree barks, including Ginkgo (Ginkgo biloba), Pine (Pinus densiflora), Platanus (Platanus), and Metasequoia (Metasequoia glyptostroboides). These were used as passive air sampler (PAS) of atmospheric polybrominated diphenyl ethers (PBDEs). Methods Tree barks were sampled from the same site. PBDEs were analyzed by highresolution gas chromatography/high-resolution mass spectrometer, and the lipid content was measured using the gravimetric method by n-hexane extraction. Results Gingko contained the highest lipid content (7.82 mg/g dry), whereas pine (4.85 mg/g dry), Platanus (3.61 mg/g dry), and Metasequoia (0.97 mg/g dry) had relatively lower content. The highest total PBDEs concentration was observed in Metasequoia (83,159.0 pg/g dry), followed by Ginkgo (53,538.4 pg/g dry), Pine (20,266.4 pg/g dry), and Platanus (12,572.0 pg/g dry). There were poor correlations between lipid content and total PBDE concentrations in tree barks (R2=0.1011, p =0.682). Among the PBDE congeners, BDE 206, 207 and 209 were highly brominated PBDEs that are sorbed to particulates in ambient air, which accounted for 90.5% (84.3-95.6%) of the concentration and were therefore identified as the main PBDE congener. The concentrations of particulate PBDEs deposited on tree barks were dependent on morphological characteristics such as surface area or roughness of barks. Conclusions Therefore, when using the tree barks as the PAS of the atmospheric PBDEs, samples belonging to same tree species should be collected to reduce errors and to obtain reliable data. PMID:25116365

Depositional characteristics of atmospheric polybrominated diphenyl ethers on tree barks.

PubMed

Chun, Man Young

2014-07-17

This study was conducted to determine the depositional characteristics of several tree barks, including Ginkgo (Ginkgo biloba), Pine (Pinus densiflora), Platanus (Platanus), and Metasequoia (Metasequoia glyptostroboides). These were used as passive air sampler (PAS) of atmospheric polybrominated diphenyl ethers (PBDEs). Tree barks were sampled from the same site. PBDEs were analyzed by highresolution gas chromatography/high-resolution mass spectrometer, and the lipid content was measured using the gravimetric method by n-hexane extraction. Gingko contained the highest lipid content (7.82 mg/g dry), whereas pine (4.85 mg/g dry), Platanus (3.61 mg/g dry), and Metasequoia (0.97 mg/g dry) had relatively lower content. The highest total PBDEs concentration was observed in Metasequoia (83,159.0 pg/g dry), followed by Ginkgo (53,538.4 pg/g dry), Pine (20,266.4 pg/g dry), and Platanus (12,572.0 pg/g dry). There were poor correlations between lipid content and total PBDE concentrations in tree barks (R(2)=0.1011, p =0.682). Among the PBDE congeners, BDE 206, 207 and 209 were highly brominated PBDEs that are sorbed to particulates in ambient air, which accounted for 90.5% (84.3-95.6%) of the concentration and were therefore identified as the main PBDE congener. The concentrations of particulate PBDEs deposited on tree barks were dependent on morphological characteristics such as surface area or roughness of barks. Therefore, when using the tree barks as the PAS of the atmospheric PBDEs, samples belonging to same tree species should be collected to reduce errors and to obtain reliable data.

Bio-drying and size sorting of municipal solid waste with high water content for improving energy recovery.

PubMed

Shao, Li-Ming; Ma, Zhong-He; Zhang, Hua; Zhang, Dong-Qing; He, Pin-Jing

2010-07-01

Bio-drying can enhance the sortability and heating value of municipal solid waste (MSW), consequently improving energy recovery. Bio-drying followed by size sorting was adopted for MSW with high water content to improve its combustibility and reduce potential environmental pollution during the follow-up incineration. The effects of bio-drying and waste particle size on heating values, acid gas and heavy metal emission potential were investigated. The results show that, the water content of MSW decreased from 73.0% to 48.3% after bio-drying, whereas its lower heating value (LHV) increased by 157%. The heavy metal concentrations increased by around 60% due to the loss of dry materials mainly resulting from biodegradation of food residues. The bio-dried waste fractions with particle size higher than 45 mm were mainly composed of plastics and papers, and were preferable for the production of refuse derived fuel (RDF) in view of higher LHV as well as lower heavy metal concentration and emission. However, due to the higher chlorine content and HCl emission potential, attention should be paid to acid gas and dioxin pollution control. Although LHVs of the waste fractions with size <45 mm increased by around 2x after bio-drying, they were still below the quality standards for RDF and much higher heavy metal pollution potential was observed. Different incineration strategies could be adopted for different particle size fractions of MSW, regarding to their combustibility and pollution property. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Dry/Wet Cycles Change the Activity and Population Dynamics of Methanotrophs in Rice Field Soil

PubMed Central

Ma, Ke; Conrad, Ralf

2013-01-01

The methanotrophs in rice field soil are crucial in regulating the emission of methane. Drainage substantially reduces methane emission from rice fields. However, it is poorly understood how drainage affects microbial methane oxidation. Therefore, we analyzed the dynamics of methane oxidation rates, composition (using terminal restriction fragment length polymorphism [T-RFLP]), and abundance (using quantitative PCR [qPCR]) of methanotroph pmoA genes (encoding a subunit of particulate methane monooxygenase) and their transcripts over the season and in response to alternate dry/wet cycles in planted paddy field microcosms. In situ methane oxidation accounted for less than 15% of total methane production but was enhanced by intermittent drainage. The dry/wet alternations resulted in distinct effects on the methanotrophic communities in different soil compartments (bulk soil, rhizosphere soil, surface soil). The methanotrophic communities of the different soil compartments also showed distinct seasonal dynamics. In bulk soil, potential methanotrophic activity and transcription of pmoA were relatively low but were significantly stimulated by drainage. In contrast, however, in the rhizosphere and surface soils, potential methanotrophic activity and pmoA transcription were relatively high but decreased after drainage events and resumed after reflooding. While type II methanotrophs dominated the communities in the bulk soil and rhizosphere soil compartments (and to a lesser extent also in the surface soil), it was the pmoA of type I methanotrophs that was mainly transcribed under flooded conditions. Drainage affected the composition of the methanotrophic community only minimally but strongly affected metabolically active methanotrophs. Our study revealed dramatic dynamics in the abundance, composition, and activity of the various type I and type II methanotrophs on both a seasonal and a spatial scale and showed strong effects of dry/wet alternation cycles, which enhanced the attenuation of methane flux into the atmosphere. PMID:23770899

Experimental study on the drying of natural latex medical gloves

NASA Astrophysics Data System (ADS)

Chankrachang, Mano; Yongyingsakthavorn, Pisit; Tohsan, Atitaya; Nontakaew, Udomkiat

2018-01-01

The purpose of this research was to study latex film drying at 70 °C using a laboratory drying oven. Two different total solid content (TSC) latex compounds, which 45% TSC and 35% TSC were used. The undried latex films were prepared according to the common procedures used in latex gloves manufacturers, that is, by dry coagulant dipping process. The experimental results such as initial moisture content, the amount of moisture and drying time of latex films in each latex compound formula were determined. After that, the results were projected to calculate on the production capacity expand by 1 million piece/day of natural latex medical gloves. Finally, the rate of moisture entering the latex drying oven and the energy consumption of the drying oven were estimated. The results indicated that when the 35% TSC of latex compound was used. The initial moisture content of latex film was higher than 45% TSC of latex compound about 7%. The drying time of 35% TSC was longer than 45% TSC for 2.5 min and consume more energy about 10%. As a result, the 45% TSC latex compound was the better way to saving energy and managing humidity in the production line. Therefore, it was found to very useful to an approximate design length and size of actual of latex drying oven and the rate of moisture entering the oven as well.

Water Content in the SW USA Mantle Lithosphere: FTIR Analysis of Dish Hill and Kilbourne Hole Pyroxenites

NASA Technical Reports Server (NTRS)

Gibler, Robert; Peslier, Anne H.; Schaffer, Lillian Aurora; Brandon, Alan D.

2014-01-01

Kilbourne Hole (NM, USA) and Dish Hill (CA, USA) mantle xenoliths sample continental mantle in two different tectonic settings. Kilbourne Hole (KH) is located in the Rio Grande rift. Dish Hill (DH) is located in the southern Mojave province, an area potentially affected by subduction of the Farallon plate beneath North America. FTIR analyses were obtained on well characterized pyroxenite, dunite and wehrlite xenoliths, thought to represent crystallized melts at mantle depths. PUM normalized REE patterns of the KH bulk-rocks are slightly LREE enriched and consistent with those of liquids generated by < 5% melting of a spinel peridotite source. Clinopyroxenes contain from 272 to 313 ppm weight H2O similar to the lower limit of KH peridotite clinopyroxenes (250-530 ppm H2O). This is unexpected as crystallized melts like pyroxenites should concentrate water more than residual mantle-like peridotites, given that H is incompatible. PUM normalized bulk REE of the DH pyroxenites are characterized by flat to LREE depleted REE profiles consistent with > 6% melting of a spinel peridotite source. Pyroxenite pyroxenes have no detectable water but one DH wehrlite, which bulk-rock is LREE enriched, has 4 ppm H2O in orthopyroxene and <1ppm in clinopyroxene. The DH pyroxenites may thus come from a dry mantle source, potentially unaffected by the subduction of the Farallon plate. These water-poor melts either originated from shallow oceanic lithosphere overlaying the Farallon slab or from continental mantle formed > 2 Ga. The Farallon subduction appears to have enriched in water the southwestern United States lithospheric mantle further east than DH, beneath the Colorado plateau.

7 CFR 58.211 - Packaging room for bulk products.

Code of Federal Regulations, 2013 CFR

2013-01-01

... maintained to keep roofs and outside areas free of dry product. Only packaging materials that are used within a day's operation may be kept in the packaging area. These materials shall be kept on metal racks or...

7 CFR 58.211 - Packaging room for bulk products.

Code of Federal Regulations, 2014 CFR

2014-01-01

... maintained to keep roofs and outside areas free of dry product. Only packaging materials that are used within a day's operation may be kept in the packaging area. These materials shall be kept on metal racks or...

7 CFR 58.211 - Packaging room for bulk products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... maintained to keep roofs and outside areas free of dry product. Only packaging materials that are used within a day's operation may be kept in the packaging area. These materials shall be kept on metal racks or...

7 CFR 58.211 - Packaging room for bulk products.

Code of Federal Regulations, 2012 CFR

2012-01-01

... maintained to keep roofs and outside areas free of dry product. Only packaging materials that are used within a day's operation may be kept in the packaging area. These materials shall be kept on metal racks or...

40 CFR 761.62 - Disposal of PCB bulk product waste.

Code of Federal Regulations, 2012 CFR

2012-07-01

... molded rubber parts and components; applied dried paints, varnishes, waxes or other similar coatings or... released or dispersed by wind or other action; or (2) Under asphalt as part of a road bed. [63 FR 35451...

40 CFR 761.62 - Disposal of PCB bulk product waste.

Code of Federal Regulations, 2014 CFR

2014-07-01

... molded rubber parts and components; applied dried paints, varnishes, waxes or other similar coatings or... released or dispersed by wind or other action; or (2) Under asphalt as part of a road bed. [63 FR 35451...

40 CFR 761.62 - Disposal of PCB bulk product waste.

Code of Federal Regulations, 2013 CFR

2013-07-01

... molded rubber parts and components; applied dried paints, varnishes, waxes or other similar coatings or... released or dispersed by wind or other action; or (2) Under asphalt as part of a road bed. [63 FR 35451...

40 CFR 761.62 - Disposal of PCB bulk product waste.

Code of Federal Regulations, 2011 CFR

2011-07-01

... molded rubber parts and components; applied dried paints, varnishes, waxes or other similar coatings or... released or dispersed by wind or other action; or (2) Under asphalt as part of a road bed. [63 FR 35451...

Effect of salt concentrations and drying methods on the quality and formation of histamine in dried milkfish (Chanos chanos).

PubMed

Hwang, Chiu-Chu; Lin, Chia-Min; Kung, Hsien-Feng; Huang, Ya-Ling; Hwang, Deng-Fwu; Su, Yi-Cheng; Tsai, Yung-Hsiang

2012-11-15

The effects of salt concentrations (0-15.0%) and drying methods on the quality of dried milkfish were studied. The results showed that the levels of aerobic plate counts, total coliform, water activity, moisture contents, total volatile basic nitrogen (TVBN) and thiobarbituric acid (TBA) of the dried milkfish samples prepared with the same drying method decreased with increased salt concentrations. The samples prepared with the cold-air drying method had better quality in term of lower TVBN and TBA values than those of samples prepared with other drying methods. The histamine contents in all samples, except two, prepared with various salt concentrations by different drying methods were less than 1.9 mg/100 g. Two unsalted samples prepared with hot-air drying at 35 °C and sun drying methods were found to contain histamine at levels of 249.7 and 67.4 mg/100 g, respectively, which were higher than the potential hazard level of 50 mg/100 g. Copyright © 2012 Elsevier Ltd. All rights reserved.

Experimental study on drying kinetic of cassava starch in a pneumatic drying system

NASA Astrophysics Data System (ADS)

Suherman, Kumoro, Andri Cahyo; Kusworo, Tutuk Djoko

2015-12-01

The aims of this study are to present the experimental research on the drying of cassava starch in a pneumatic dryer, to describe its drying curves, as well as to calculate its thermal efficiency. The effects of operating conditions, namely the inlet air temperature (60-100 °C) and solid-gas flow rate ratio (Ms/Mg 0.1-0.3) were studied. Heat transfer is accomplished through convection mechanism in a drying chamber based on the principle of direct contact between the heated air and the moist material. During the drying process, intensive heat and mass transfer between the drying air and the cassava starch take place. In order to meet the SNI standards on solid water content, the drying process was done in two cycles. The higher the temperature of the drying air, the lower the water content of the solids exiting the dryer. Thermal efficiency of the 2nd cycle was found to be lower than the 1st cycle.

Chemical composition, antioxidant capacity, and sensory quality of dried jujube fruits as affected by cultivar and drying method.

PubMed

Wojdyło, Aneta; Figiel, Adam; Legua, Pilar; Lech, Krzysztof; Carbonell-Barrachina, Ángel A; Hernández, Francisca

2016-09-15

The aim of this study was to determine the effect of different dying methods, such as convective drying (CD: 50, 60, 70 °C), vacuum-microwave drying (VMD: 120, 480, 480-120 W), a combination of convective pre-drying and vacuum-microwave finish drying [(CPD (60 °C)-VMFD (480-120 W)], and freeze-drying (FD) on key quality parameters of dried jujube fruits (cv. "GAL", "MSI", and "PSI"). The parameters studied included bioactive compounds (flavan-3-ols and flavonols, identified by LC-PDA-MS, and vitamin C), antioxidant capacity (ABTS and FRAP), and sensory attributes (e.g. hardness, jujube-ID, and sweetness). The best quality of the dried product (high contents of bioactive compounds and high intensity of key sensory attributes) was found in fruits treated by FD and VMD 480-120 W. The best cultivars were "PSI" and "GAL" from the point of view of bioactive content and sensory quality, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Rheological, Chemical and Physical Characteristics of Golden Berry (Physalis peruviana L.) after Convective and Microwave Drying.

PubMed

Nawirska-Olszańska, Agnieszka; Stępień, Bogdan; Biesiada, Anita; Kolniak-Ostek, Joanna; Oziembłowski, Maciej

2017-07-29

Studies on methods for fixing foods (with a slight loss of bioactive compounds) and obtaining attractive products are important with respect to current technology. The drying process allows for a product with highly bioactive properties. Drying of Physalis fruit was carried out in a conventional manner, and in a microwave under reduced pressure at 120 W and 480 W. After drying, the fruits were subjected to strength and rheological tests. Water activity, content of carotenoids and polyphenols and antioxidant activity as well as colour were also examined. The study showed that Physalis is a difficult material for drying. The best results were obtained using microwave drying at a power of 480 W. Physalis fruit microwave-dried by this method is characterized by higher resistance to compression than the fruit dried by convection. Dried fruit obtained in this way was characterized by higher contents of bioactive compounds, better antioxidant properties, and at the same time the lowest water activity.

Rheological, Chemical and Physical Characteristics of Golden Berry (Physalis peruviana L.) after Convective and Microwave Drying

PubMed Central

Nawirska-Olszańska, Agnieszka; Stępień, Bogdan; Biesiada, Anita; Kolniak-Ostek, Joanna; Oziembłowski, Maciej

2017-01-01

Studies on methods for fixing foods (with a slight loss of bioactive compounds) and obtaining attractive products are important with respect to current technology. The drying process allows for a product with highly bioactive properties. Drying of Physalis fruit was carried out in a conventional manner, and in a microwave under reduced pressure at 120 W and 480 W. After drying, the fruits were subjected to strength and rheological tests. Water activity, content of carotenoids and polyphenols and antioxidant activity as well as colour were also examined. The study showed that Physalis is a difficult material for drying. The best results were obtained using microwave drying at a power of 480 W. Physalis fruit microwave-dried by this method is characterized by higher resistance to compression than the fruit dried by convection. Dried fruit obtained in this way was characterized by higher contents of bioactive compounds, better antioxidant properties, and at the same time the lowest water activity. PMID:28758918

21 CFR 184.1979a - Reduced lactose whey.

Code of Federal Regulations, 2013 CFR

2013-04-01

....199 (dry sample), entitled “Fat in Dried Milk (45)—Official Final Action.” (iii) Ash content, 11 to 27...—Official Final Action” under the heading “Dried Milk, Nonfat Dry Milk, and Malted Milk.” (iv) Lactose... section 16.192, entitled “Moisture (41)—Official Final Action” under the heading “Dried Milk, Nonfat Dry...

21 CFR 184.1979a - Reduced lactose whey.

Code of Federal Regulations, 2012 CFR

2012-04-01

....199 (dry sample), entitled “Fat in Dried Milk (45)—Official Final Action.” (iii) Ash content, 11 to 27...—Official Final Action” under the heading “Dried Milk, Nonfat Dry Milk, and Malted Milk.” (iv) Lactose... section 16.192, entitled “Moisture (41)—Official Final Action” under the heading “Dried Milk, Nonfat Dry...

Change in enzyme production by gradually drying culture substrate during solid-state fermentation.

PubMed

Ito, Kazunari; Gomi, Katsuya; Kariyama, Masahiro; Miyake, Tsuyoshi

2015-06-01

The influence of drying the culture substrate during solid-state fermentation on enzyme production was investigated using a non-airflow box. The drying caused a significant increase in enzyme production, while the mycelium content decreased slightly. This suggests that changes in the water content in the substrate during culture affect enzyme production in fungi. Copyright © 2014 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Effect of stopper processing conditions on moisture content and ramifications for lyophilized products: comparison of "low" and "high" moisture uptake stoppers.

PubMed

Donovan, P D; Corvari, V; Burton, M D; Rajagopalan, N

2007-01-01

The purpose of this study was to evaluate the effect of processing and storage on the moisture content of two commercially available, 13-mm lyophilization stoppers designated as low moisture (LM) and high moisture (HM) uptake stoppers. The stopper moisture studies included the effect of steam sterilization time, drying time and temperature, equilibrium moisture content, lyophilization and moisture transfer from stopper to a model-lactose lyophilized cake. Results indicated that both stoppers absorbed significant amounts of moisture during sterilization and that the HM stopper absorbed significantly more water than the LM stopper. LM and HM stoppers required approximately 2 and 8 h drying at 105 degrees C, respectively, to achieve final moisture content of not more than 0.5 mg/stopper. Following drying, stopper moisture levels equilibrated rapidly to ambient storage conditions. The apparent equilibrium moisture level was approximately 7 times higher in the HM versus LM stopper. Freeze-drying had minimal effect on the moisture content of dried stoppers. Finally, moisture transfer from the stopper to the lyophilized product is dependent on the initial stopper water content and storage temperature. To better quantify the ramifications of stopper moisture, projections of moisture uptake over the shelf life of a drug product were calculated based on the product-contact surface area of stoppers. Attention to stopper storage conditions prior to use, in addition to processing steps, are necessary to minimize stability issues especially in low-fill, mass lyophilized products.

Loss of sulfur dioxide and changes in some chemical properties of Malatya apricots (Prunus armeniaca L.) during sulfuring and drying.

PubMed

Türkyılmaz, Meltem; Özkan, Mehmet; Güzel, Nihal

2014-09-01

This study was conducted to determine the differences in some analytical properties of four apricot cultivars and to determine the changes in these analytical properties during sulfuring and sun-drying. There were significant differences in the contents of polyphenols, carotenoids and organic acids (OA) as well as antioxidant activities (AOAs) of the cultivars (P < 0.05). After sulfuring and drying, considerable reductions were detected in the contents of total polyphenols (TPCs, 11-26%), OAs (4-32%) and β-carotene (6-21%), and AOAs (2-21%) of the samples. Sun-drying resulted in 71-83% decreases in sulfur dioxide (SO2 ) contents of sulfured-dried apricots (SDAs) in comparison with apricots immediately after sulfuring. As the TPCs increased, the SO2 absorption by the samples also increased. In contrast, the OA contents had no effect on SO2 absorption, but an increase in OA content resulted in an increase in the browning values of the SDAs. As expected, increases in contents of ferulic acid (r = 0.932), chlorogenic acid (r = 0.850), epicatechin (r = 0.804) and quercetin (r = 0.750) led to an increase in browning values of the SDAs. There were significant effects of cultivar and processing on the physico-chemical properties investigated in the study, and with the absorption of SO2 and the formation of a brown colour in the samples. © 2014 Society of Chemical Industry.

Physicochemical properties of respirable-size lunar dust

NASA Astrophysics Data System (ADS)

McKay, D. S.; Cooper, B. L.; Taylor, L. A.; James, J. T.; Thomas-Keprta, K.; Pieters, C. M.; Wentworth, S. J.; Wallace, W. T.; Lee, T. S.

2015-02-01

We separated the respirable dust and other size fractions from Apollo 14 bulk sample 14003,96 in a dry nitrogen environment. While our toxicology team performed in vivo and in vitro experiments with the respirable fraction, we studied the size distribution and shape, chemistry, mineralogy, spectroscopy, iron content and magnetic resonance of various size fractions. These represent the finest-grained lunar samples ever measured for either FMR np-Fe0 index or precise bulk chemistry, and are the first instance we know of in which SEM/TEM samples have been obtained without using liquids. The concentration of single-domain, nanophase metallic iron (np-Fe0) increases as particle size diminishes to 2 μm, confirming previous extrapolations. Size-distribution studies disclosed that the most frequent particle size was in the 0.1-0.2 μm range suggesting a relatively high surface area and therefore higher potential toxicity. Lunar dust particles are insoluble in isopropanol but slightly soluble in distilled water (~0.2 wt%/3 days). The interaction between water and lunar fines, which results in both agglomeration and partial dissolution, is observable on a macro scale over time periods of less than an hour. Most of the respirable grains were smooth amorphous glass. This suggests less toxicity than if the grains were irregular, porous, or jagged, and may account for the fact that lunar dust is less toxic than ground quartz.

Metabolomics method based on ultra high performance liquid chromatography with time-of-flight mass spectrometry to analyze toxins in fresh and dried toad venom.

PubMed

Ma, Hongyue; Niu, Huixia; Cao, Qin; Zhou, Jing; Gong, Yan; Zhu, Zhenhua; Lv, Xiang; Di, Liuqing; Qian, Dawei; Wu, Qinan; Duan, Jin'ao

2016-12-01

Drying is a critical step to prolong the storage time in natural medicine processing but it changes the chemical characteristics of the product. In this study, research was performed to characterize the metabolomic changes in toad venom induced by vacuum-drying at 60°C and air-drying at room temperature by ultra high performance liquid chromatography coupled with pattern recognition approaches. In total 52 metabolites, down-regulated or up-regulated, were identified as potential chemical markers. Compared with fresh toad venom, vacuum-drying at 60°C succeeded in raising the conjugated-type bufadienolide content significantly, while the content of free-type bufadienolides were slightly reduced. On the other hand, toad venom air-dried at room temperature presented a relatively low amount of bufadienolides compared with fresh venom. For example, the content of several known anti-tumor components (gamabufotalin, bufotalin, cinobufagin, etc.) were significantly reduced. The 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide bioassay further showed that venom air-dried at room temperature had weaker anti-tumor activity on human hepatocellular carcinoma SMMC-7721 proliferation in vitro than samples vacuum-dried at 60°C. These results showed that the great metabolomic changes of toad venom occurred during the drying process, suggesting that a proper drying procedure is important for sustaining the chemical quality of natural medicines. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Third generation snacks manufactured from orange by-products: physicochemical and nutritional characterization.

PubMed

Tovar-Jiménez, Xochitl; Caro-Corrales, José; Gómez-Aldapa, Carlos A; Zazueta-Morales, José; Limón-Valenzuela, Víctor; Castro-Rosas, Javier; Hernández-Ávila, Juan; Aguilar-Palazuelos, Ernesto

2015-10-01

A mixture of orange vesicle flour, commercial nixtamalized corn flour and potato starch was extruded using a Brabender Laboratory single screw extruder (2:1 L/D). The resulting pellets were expanded by microwaves. Expansion index, bulk density, penetration force, carotenoid content, and dietary fiber were measured for this third-generation snack and optimum production conditions were estimated. Response surface methodology was applied using a central composite rotatable experimental design to evaluate the effect of moisture content and extrusion temperature. Temperature mainly affected the expansion index, bulk density and penetration force, while carotenoids content was affected by moisture content. Surface overlap was used to identify optimum processing conditions: temperature: 128-130 °C; moisture content: 22-24 %. Insoluble dietary fiber decreased and soluble dietary fiber increased after extrusion.

21 CFR 526.820 - Erythromycin.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Lactating cows: After milking, cleaning, and disinfecting, infuse contents of a single 6-milliliter syringe... infusions. (ii) Dry cows: After milking, cleaning, and disinfecting, infuse contents of a single 12... Streptococcus uberis in lactating or dry cows. (3) Limitations. Milk taken from animals during treatment and for...

Effect of air-flow on biodrying method of municipal solid waste in Indonesia

NASA Astrophysics Data System (ADS)

Kristanto, Gabriel Andari; Hanany, Ismi

2017-11-01

The process of bio-drying could be an interesting solution for municipal solid waste management and energy demand in Indonesia. By using the heat from bio-degradation process consists in bio-drying, moisture content in a solid waste can be reduced. Solid wastes with a low moisture content, could be used as a fuel with a good energy content. In this study, 85% of garden wastes and 15% of food waste from Indonesia's municipal solid waste were bio-dried in aerobic condition using 3 variations of air flow-rates, which were 8 L/min.kg; 10 L/min.kg; and 12 L/min.kg. The experiment performs with three different reactors with known volume 75cm × 50cm × 40cm and using Styrofoam as an insulation. The process of bio-drying lasted 21 days. In the end, the experiment with 10 L/min.kg aeration, has the lowest moisture contents about 23% with high temperature and NHV about 3595.29 kcal/kg.

Development of a multivariate calibration model for the determination of dry extract content in Brazilian commercial bee propolis extracts through UV-Vis spectroscopy

NASA Astrophysics Data System (ADS)

Barbeira, Paulo J. S.; Paganotti, Rosilene S. N.; Ássimos, Ariane A.

2013-10-01

This study had the objective of determining the content of dry extract of commercial alcoholic extracts of bee propolis through Partial Least Squares (PLS) multivariate calibration and electronic spectroscopy. The PLS model provided a good prediction of dry extract content in commercial alcoholic extracts of bee propolis in the range of 2.7 a 16.8% (m/v), presenting the advantage of being less laborious and faster than the traditional gravimetric methodology. The PLS model was optimized with outlier detection tests according to the ASTM E 1655-05. In this study it was possible to verify that a centrifugation stage is extremely important in order to avoid the presence of waxes, resulting in a more accurate model. Around 50% of the analyzed samples presented content of dry extract lower than the value established by Brazilian legislation, in most cases, the values found were different from the values claimed in the product's label.

Seasonal atmospheric deposition variations of polychlorinated biphenyls (PCBs) and comparison of some deposition sampling techniques.

PubMed

Birgül, Askın; Tasdemir, Yücel

2011-03-01

Ambient air and bulk deposition samples were collected between June 2008 and June 2009. Eighty-three polychlorinated biphenyl (PCB) congeners were targeted in the samples. The average gas and particle PCB concentrations were found as 393 ± 278 and 70 ± 102 pg/m(3), respectively, and 85% of the atmospheric PCBs were in the gas phase. Bulk deposition samples were collected by using a sampler made of stainless steel. The average PCB bulk deposition flux value was determined as 6,020 ± 4,350 pg/m(2) day. The seasonal bulk deposition fluxes were not statistically different from each other, but the summer flux had higher values. Flux values differed depending on the precipitation levels. The average flux value in the rainy periods was 7,480 ± 4,080 pg/m(2) day while the average flux value in dry periods was 5,550 ± 4,420 pg/m(2) day. The obtained deposition values were lower than the reported values given for the urban and industrialized areas, yet close to the ones for the rural sites. The reported deposition values were also influenced by the type of the instruments used. The average dry deposition and total deposition velocity values calculated based on deposition and concentration values were found as 0.23 ± 0.21 and 0.13 ± 0.13 cm/s, respectively.

Effect of moisture of municipal biowaste on start-up and efficiency of mesophilic and thermophilic dry anaerobic digestion.

PubMed

Li, Chaoran; Mörtelmaier, Christoph; Winter, Josef; Gallert, Claudia

2014-09-01

Methane production from biowaste with 20-30% dry matter (DM) by box-type dry anaerobic digestion and contributing bacteria were determined for incubation at 20, 37 and 55 °C. The same digestion efficiency as for wet anaerobic digestion of biowaste was obtained for dry anaerobic digestion with 20% DM content at 20, 37 and 55 °C and with 25% DM content at 37 and 55 °C. No or only little methane was produced in dry anaerobic reactors with 30% DM at 20, 37 or 55 °C. Population densities in the 20-30% DM-containing biowaste reactors were similar although in mesophilic and thermophilic biowaste reactors with 30% DM content significantly less but phylogenetically more diverse archaea existed. Biogas production in the 20% and 25% DM assays was catalyzed by Methanosarcinales and Methanomicrobiales. In all assays Pelotomaculum and Syntrophobacter species were dominant propionate degraders. Copyright © 2014 Elsevier Ltd. All rights reserved.

Contents Changes of Triterpenic Acids, Nucleosides, Nucleobases, and Saccharides in Jujube (Ziziphus jujuba) Fruit During the Drying and Steaming Process.

PubMed

Guo, Sheng; Duan, Jin-Ao; Zhang, Ying; Qian, Dawei; Tang, Yuping; Zhu, Zhenhua; Wang, Hanqing

2015-12-12

Chinese jujube (Ziziphus jujuba), a medicinal and edible plant, is widely consumed in Asian countries owing to the remarkable health activities of its fruits. To facilitate selection of the suitable processing method for jujube fruits, in this study their contents of triterpenic acids, nucleosides, nucleobases and saccharides after drying and steaming treatment were determined using ultra-high performance liquid chromatography and high performance liquid chromatography coupled with evaporative light scattering detector methods. The results showed that except for sucrose, the content levels of most analytes were increasing in the jujube fruits during drying treatment at 45 °C. The levels of cyclic nucleotides such as adenosine 3',5'-cyclic monophosphate and guanosine 3',5'-cyclic monophosphate, were significantly decreased after the fruits were steamed. Therefore, owing to the bioactivities of these components for human health, the dried fruits would be the better choice as medicinal material or functional food, and dried jujube fruit should not be further steamed.

Ash Analysis

NASA Astrophysics Data System (ADS)

Marshall, Maurice R.

Ash refers to the inorganic residue remaining after either ignition or complete oxidation of organic matter in a foodstuff. A basic knowledge of the characteristics of various ashing procedures and types of equipment is essential to ensure reliable results. Two major types of ashing are used: dry ashing, primarily for proximate composition and for some types of specific mineral analyses; wet ashing (oxidation), as a preparation for the analysis of certain minerals. Microwave systems now are available for both dry and wet ashing, to speed the processes. Most dry samples (i.e., whole grain, cereals, dried vegetables) need no preparation, while fresh vegetables need to be dried prior to ashing. High-fat products such as meats may need to be dried and fat extracted before ashing. The ash content of foods can be expressed on either a wet weight (as is) or on a dry weight basis. For general and food-specific information on measuring ash content, see references (1-11).

Dry Kraft Pulping at Ambient Pressure for Cost Effective Energy Saving and Pollution Deduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yulin Deng; Art Ragauskas

Sponsored by the DOE Industrial Energy Efficiency Grand Challenge program, our research team at the Georgia Institute of Technology conducted laboratory studies and confirmed the concept of making wood pulp using a dry pulping technology. This technology is a new process different from any prior pulping technology used in Kraft and CTMP pulping. Three different kinds of dry pulping methods were investigated. (a) Dry Pulping at Atmospheric Pressure: The first one is to dry and bake the pretreated woodchips in a conventional oven at atmospheric pressure without the use of a catalyst. (b) Dry Pulping at Reduced Pressure: The secondmore » method is to dry the pretreated woodchips first in a vacuum oven in the presence of anthraquinone (AQ) as a pulping catalyst, followed by baking at elevated temperature. (c) Liquid Free Chemical Pulping, LFCP. The third method is to first remove the free water of pretreated woodchips, followed by dry pulping using a conventional Kraft pulping digester with AQ and triton as additives. Method one: Experimental results indicated that Dry Pulping at Atmospheric Pressure could produce pulp with higher brightness and lower bulk than conventional Kraft pulp. However, tensile strength of the acquired pulp is much lower than traditional Kraft pulp, and their Kappa number and energy consumption are higher than conventional Kraft pulp. By fully analyzing the results, we concluded that wood fibers might be damaged during the drying process at elevated temperature. The main reason for wood fiber damage is that a long drying time was used during evaporation of water from the woodchips. This resulted in an un-uniform reaction condition on the woodchips: the outside layer of the woodchips was over reacted while inside the woodchips did not reacted at all. To solve this problem, dry pulping at reduced pressure was investigated. Method two: To achieve uniform reaction throughout the entire reaction system, the water inside the pretreated woodchips was evaporated first under vacuum condition at low temperature. Then, the dry woodchips were baked at high temperature (120-130 C) at atmospheric pressure. The qualities of the pulp made with this method were improved compared to that made with method one. The pulp shows higher brightness and lower bulk than Kraft pulping. The tensile strength is significantly higher than the pulp made from the first method. Although the pulp is stronger than that of TMP pulp, it is still lower than conventional Kraft fiber. Method Three: The third dry method was done in a Kraft pulping digester at elevated pressure but without free liquid in the digester. With this method, pulp that has almost the same qualities as conventional Kraft pulp could be produced. The screen yield, Kappa number, fiber brightness, pulp strength and pulp bulk are almost identical to the conventional Kraft pulp. The key advantages of this dry pulping method include ca. 55 % of cooking energy saved during the pulping process, as high as 50 wt% of NaOH saving as well as 3 wt% of Na2S saving comparing to Kraft one. By analyzing fiber properties, yields, chemical and energy consumptions, we concluded that the dry pulping method based on Liquid Free Chemical Pulping, LFCP, could be very attractive for the pulp and paper industry. More fundamental studies and scale up trials are needed to fully commercialize the technology. We expect to conduct pilot trials between 12 to 24 months of period if the DOE or industry can provide continual research funding. Based on the technology we demonstrated in this report, several pilot trial facilities in the United States will be available after small modifications. For example, the Herty Foundation in Savannah, Georgia is one of these potential locations. DOE funding for continuous study and final lead to commercialization of the technique is important.« less

How to use hand-held computers to evaluate wood drying.

Treesearch

Howard N. Rosen; Darrell S. Martin

1985-01-01

Techniques have been developed to evaluate end generate wood drying curves with hand-held computers (3-5K memory). Predictions of time to dry to a specific moisture content, drying rates, and other characteristics of wood drying curves can be made. The paper describes the development of programs and illustrates their use.

Drying of Pigment-Cellulose Nanofibril Substrates

PubMed Central

Timofeev, Oleg; Torvinen, Katariina; Sievänen, Jenni; Kaljunen, Timo; Kouko, Jarmo; Ketoja, Jukka A.

2014-01-01

A new substrate containing cellulose nanofibrils and inorganic pigment particles has been developed for printed electronics applications. The studied composite structure contains 80% fillers and is mechanically stable and flexible. Before drying, the solids content can be as low as 20% due to the high water binding capacity of the cellulose nanofibrils. We have studied several drying methods and their effects on the substrate properties. The aim is to achieve a tight, smooth surface keeping the drying efficiency simultaneously at a high level. The methods studied include: (1) drying on a hot metal surface; (2) air impingement drying; and (3) hot pressing. Somewhat surprisingly, drying rates measured for the pigment-cellulose nanofibril substrates were quite similar to those for the reference board sheets. Very high dewatering rates were observed for the hot pressing at high moisture contents. The drying method had significant effects on the final substrate properties, especially on short-range surface smoothness. The best smoothness was obtained with a combination of impingement and contact drying. The mechanical properties of the sheets were also affected by the drying method and associated temperature. PMID:28788220

Genome-Wide Association Mapping of Correlated Traits in Cassava: Dry Matter and Total Carotenoid Content.

PubMed

Rabbi, Ismail Y; Udoh, Lovina I; Wolfe, Marnin; Parkes, Elizabeth Y; Gedil, Melaku A; Dixon, Alfred; Ramu, Punna; Jannink, Jean-Luc; Kulakow, Peter

2017-11-01

Cassava is a starchy root crop cultivated in the tropics for fresh consumption and commercial processing. Primary selection objectives in cassava breeding include dry matter content and micronutrient density, particularly provitamin A carotenoids. These traits are negatively correlated in the African germplasm. This study aimed at identifying genetic markers associated with these traits and uncovering whether linkage and/or pleiotropy were responsible for observed negative correlation. A genome-wide association mapping using 672 clones genotyped at 72,279 single nucleotide polymorphism (SNP) loci was performed. Root yellowness was used indirectly to assess variation in carotenoid content. Two major loci for root yellowness were identified on chromosome 1 at positions 24.1 and 30.5 Mbp. A single locus for dry matter content that colocated with the 24.1 Mbp peak for carotenoids was identified. Haplotypes at these loci explained 70 and 37% of the phenotypic variability for root yellowness and dry matter content, respectively. Evidence of megabase-scale linkage disequilibrium (LD) around the major loci of the two traits and detection of the major dry matter locus in independent analysis for the white- and yellow-root subpopulations suggests that physical linkage rather that pleiotropy is more likely to be the cause of the negative correlation between the target traits. Moreover, candidate genes for carotenoid () and starch biosynthesis ( and ) occurred in the vicinity of the identified locus at 24.1 Mbp. These findings elucidate the genetic architecture of carotenoids and dry matter in cassava and provide an opportunity to accelerate breeding of these traits. Copyright © 2017 Crop Science Society of America.

Towards an efficient protocol for the determination of triterpenic acids in olive fruit: a comparative study of drying and extraction methods.

PubMed

Goulas, Vlasios; Manganaris, George A

2012-01-01

Triterpenic acids, such as maslinic acid and oleanolic acid, are commonly found in olive fruits and have been associated with many health benefits. The drying and extraction methods, as well as the solvents used, are critical factors in the determination of their concentration in plant tissues. Thus, there is an emerging need for standardisation of an efficient extraction protocol that determines triterpenic acid content in olive fruits. To evaluate common extraction methods of triterpenic acids from olive fruits and to determine the effect of the drying method on their content in order to propose an optimum protocol for their quantification. The efficacy of different drying and extraction methods was evaluated through the quantification of maslinic acid and oleanolic acid contents using the reversed-phase HPLC technique. Data showed that ultrasonic assisted extraction with ethanol or a mixture of ethanol:methanol (1:1, v/v) resulted in the recovery of significantly higher amounts of triterpenic acids than other methods used. The drying method also affected the estimated triterpenic acid content; frozen or lyophilised olive fruit material gave higher yields of triterpenic acids compared with air-dried material at both 35°C and 105°C. This study provides a rapid and low-cost extraction method, i.e. ultrasonic assisted extraction with an eco-friendly solvent such as ethanol, from frozen or lyophilised olive fruit for the accurate determination of the triterpenic acid content in olive fruit. Copyright © 2011 John Wiley & Sons, Ltd.

Acrylamide content distribution and possible alternative ingredients for snack foods.

PubMed

Cheng, Wei Chih; Sun, De Chao; Chou, Shin Shou; Yeh, An I

2012-12-01

Acrylamide (AA) contents in 294 snack foods including cereal-based, root- and tuber-based, and seafood-based foods, nuts, dried beans, and dried fruits purchased in Taiwan were determined by gas chromatography-mass spectrometry in this study. The highest levels of average AA content were found in root- and tuber-based snack foods (435 μg/kg), followed by cereal-based snack foods (299 μg/kg). Rice flour-based, seafood-based, and dried fruit snack foods had the lowest average AA content (<50 μg/kg). This is the first large surveillance of AA content in snack foods in Taiwan. The results could provide important data regarding intake information from the snack foods. In addition, the results showed a great diversity of AA content in snack foods prepared from different ingredients. Rice- and seafood-based products had much lower AA than those made from other ingredients. This information could constitute a good reference for consumers to select products for healthy snacking.

Potential of Near-Infrared Chemical Imaging as Process Analytical Technology Tool for Continuous Freeze-Drying.

PubMed

Brouckaert, Davinia; De Meyer, Laurens; Vanbillemont, Brecht; Van Bockstal, Pieter-Jan; Lammens, Joris; Mortier, Séverine; Corver, Jos; Vervaet, Chris; Nopens, Ingmar; De Beer, Thomas

2018-04-03

Near-infrared chemical imaging (NIR-CI) is an emerging tool for process monitoring because it combines the chemical selectivity of vibrational spectroscopy with spatial information. Whereas traditional near-infrared spectroscopy is an attractive technique for water content determination and solid-state investigation of lyophilized products, chemical imaging opens up possibilities for assessing the homogeneity of these critical quality attributes (CQAs) throughout the entire product. In this contribution, we aim to evaluate NIR-CI as a process analytical technology (PAT) tool for at-line inspection of continuously freeze-dried pharmaceutical unit doses based on spin freezing. The chemical images of freeze-dried mannitol samples were resolved via multivariate curve resolution, allowing us to visualize the distribution of mannitol solid forms throughout the entire cake. Second, a mannitol-sucrose formulation was lyophilized with variable drying times for inducing changes in water content. Analyzing the corresponding chemical images via principal component analysis, vial-to-vial variations as well as within-vial inhomogeneity in water content could be detected. Furthermore, a partial least-squares regression model was constructed for quantifying the water content in each pixel of the chemical images. It was hence concluded that NIR-CI is inherently a most promising PAT tool for continuously monitoring freeze-dried samples. Although some practicalities are still to be solved, this analytical technique could be applied in-line for CQA evaluation and for detecting the drying end point.

Carotenoid content of the varieties Jaranda and Jariza (Capsicumannuum L.) and response during the industrial slow drying and grinding steps in paprika processing.

PubMed

Mínguez-Mosquera, M I; Pérez-Gálvez, A; Garrido-Fernández, J

2000-07-01

Fruits of the pepper varieties Jaranda and Jariza (Capsicum annuum L. ) ripen as a group, enabling a single harvesting, showed a uniform carotenoid content that is high enough (7.9 g/kg) for the production of paprika. The drying system at mild temperature showed that fruits with moisture content of 85-88% generated a dry product with carotenoid content equal to or higher than the initial one. Those high moisture levels allowed the fruits to have a longer period of metabolic activity, increasing the yellow fraction, the red fraction, or both as a function of what biosynthetic process was predominant. This fact indicates under-ripeness of the fruits in the drying step. The results obtained allow us to establish that both varieties, Jaranda and Jariza, fit the dehydration process employed, yielding a dry fruit with carotenoid concentration similar to that the initial one. During the grinding step of the dry fruit, the heat generated by the hammers of the mill caused degradation of the yellow fraction, while the red fraction is maintained. The ripeness state of the harvested fruits and the appropriateness or severity of the processing steps are indicated by the ratio of red to yellow (R/Y) and/or red to total (R/T) pigments, since fluctuations in both fractions and in total pigments are reflected in and monitored by these parameters.

The impacts of pyrolysis temperature and feedstock type on biochar properties and the effects of biochar application on the properties of a sandy loam

NASA Astrophysics Data System (ADS)

Aston, Steve; Doerr, Stefan; Street-Perrott, Alayne

2013-04-01

The production of biochar and its application to soil has the potential to make a significant contribution to climate change mitigation whilst simultaneously improving soil fertility, crop yield and soil water-holding capacity. Biochar is produced from various biomass feedstock materials at varying pyrolysis temperatures, but relatively little is known about how these parameters affect the properties of the resultant biochars and their impact on the properties of the soils to which they are subsequently applied. Salix viminalis, M. giganteus and Picea sitchensis feedstocks were chipped then sieved to 2 - 5 mm, oven dried to constant weight, then pyrolyzed at 350, 500, 600 and 800° C in a nitrogen-purged tube furnace. Biochar yields were measured by weighing the mass of each sample before and after pyrolysis. Biochar hydrophobicity was assessed by using a goniometer to measure water-droplet contact-angles. Cation-exchange-capacity (CEC) was measured using the ammonium acetate method. Biochars were also produced in a rotary kiln from softwood pellets at 400, 500, 600 and 700° C then ground to 0.4 - 1 mm and applied to a sandy loam at a rate of 50 g kg-1. Bulk densities of these soil-biochar mixtures were measured on a tapped, dry, basis. The water-holding-capacity (WHC) of each mixture was measured gravimetrically following saturation and free-draining. The filter paper method was used to assess how pyrolysis temperature influences the effect of biochar application on matric suction. For all feedstocks, large decreases in biochar yield were observed between the pyrolysis temperatures of 350° C and 500° C. For Salix viminalis and M. giganteus feedstocks, subsequent reductions in the yield with increasing pyrolysis temperature were much lower. There were significant differences in hydrophobicity between biochars produced from different biomass and mean biochar hydrophobicity decreased with increasing pyrolysis temperature for all feedstocks. Results for CEC and WHC measurements will also be presented. With water contents of 0.04, 0.08 and 0.16 cm3 cm-3, the mean matric suctions of a sandy loam were higher when biochar was added. However, the differences were only statistically significant at a water content of 0.16 cm3 cm-3, where biochar produced at 500° C had the highest suction. Biochar additions always lowered the mean bulk density of a sandy loam, but there were significant differences in the extent to which biochars produced at different temperatures did this. Biochar yields and hydrophobicity vary according to feedstock type and decrease with increasing pyrolysis temperature. Application of biochar can significantly reduce bulk density but the extent of this effect varies according to the pyrolysis temperature at which the biochar is produced. Pyrolysis temperature can have a significant influence on how biochars affect soil suction. Acknowledgements: This study was funded by a UK Natural Environment Research Council (NERC) Doctoral Training Grant: NE/H525154/1.

Folate content in faba beans (Vicia faba L.)—effects of cultivar, maturity stage, industrial processing, and bioprocessing

PubMed Central

Hefni, Mohammed E; Shalaby, Mohamed T; Witthöft, Cornelia M

2015-01-01

Faba beans are an important source of folate and commonly consumed in Egypt. This study examined the effects of Egyptian industrial food processing (e.g., canning and freezing), germination, cultivar, and maturity stages on folate content, with the aim to develop a candidate functional canned faba bean food with increased folate content. The folate content in four cultivars of green faba beans ranged from 110 to 130 μg 100 g−1 fresh weight (535–620 μg 100 g−1 dry matter [DM]), which was four- to sixfold higher than in dried seeds. Industrial canning of dried seeds resulted in significant folate losses of ∼20% (P = 0.004), while industrial freezing had no effect. Germination of faba beans increased the folate content by >40% (P < 0.0001). A novel industrial canning process involving pregermination of dried faba beans resulted in a net folate content of 194 μg 100 g−1 DM, which is 52% more than in conventional canned beans. The consumption of green faba beans should be recommended, providing ∼120 μg dietary folate equivalents per 100 g/portion. PMID:25650294

Measuring Soil Moisture in Skeletal Soils Using a COSMOS Rover

NASA Astrophysics Data System (ADS)

Medina, C.; Neely, H.; Desilets, D.; Mohanty, B.; Moore, G. W.

2017-12-01

The presence of coarse fragments directly influences the volumetric water content of the soil. Current surface soil moisture sensors often do not account for the presence of coarse fragments, and little research has been done to calibrate these sensors under such conditions. The cosmic-ray soil moisture observation system (COSMOS) rover is a passive, non-invasive surface soil moisture sensor with a footprint greater than 100 m. Despite its potential, the COSMOS rover has yet to be validated in skeletal soils. The goal of this study was to validate measurements of surface soil moisture as taken by a COSMOS rover on a Texas skeletal soil. Data was collected for two soils, a Marfla clay loam and Chinati-Boracho-Berrend association, in West Texas. Three levels of data were collected: 1) COSMOS surveys at three different soil moistures, 2) electrical conductivity surveys within those COSMOS surveys, and 3) ground-truth measurements. Surveys with the COSMOS rover covered an 8000-h area and were taken both after large rain events (>2") and a long dry period. Within the COSMOS surveys, the EM38-MK2 was used to estimate the spatial distribution of coarse fragments in the soil around two COSMOS points. Ground truth measurements included coarse fragment mass and volume, bulk density, and water content at 3 locations within each EM38 survey. Ground-truth measurements were weighted using EM38 data, and COSMOS measurements were validated by their distance from the samples. There was a decrease in water content as the percent volume of coarse fragment increased. COSMOS estimations responded to both changes in coarse fragment percent volume and the ground-truth volumetric water content. Further research will focus on creating digital soil maps using landform data and water content estimations from the COSMOS rover.

Increases in soil water content after the mortality of non-native trees in oceanic island forest ecosystems are due to reduced water loss during dry periods.

PubMed

Hata, Kenji; Kawakami, Kazuto; Kachi, Naoki

2016-03-01

The control of dominant, non-native trees can alter the water balance of soils in forest ecosystems via hydrological processes, which results in changes in soil water environments. To test this idea, we evaluated the effects of the mortality of an invasive tree, Casuarina equisetifolia Forst., on the water content of surface soils on the Ogasawara Islands, subtropical islands in the northwestern Pacific Ocean, using a manipulative herbicide experiment. Temporal changes in volumetric water content of surface soils at 6 cm depth at sites where all trees of C. equisetifolia were killed by herbicide were compared with those of adjacent control sites before and after their mortality with consideration of the amount of precipitation. In addition, the rate of decrease in the soil water content during dry periods and the rate of increase in the soil water content during rainfall periods were compared between herbicide and control sites. Soil water content at sites treated with herbicide was significantly higher after treatment than soil water content at control sites during the same period. Differences between initial and minimum values of soil water content at the herbicide sites during the drying events were significantly lower than the corresponding differences in the control quadrats. During rainfall periods, both initial and maximum values of soil water contents in the herbicided quadrats were higher, and differences between the maximum and initial values did not differ between the herbicided and control quadrats. Our results indicated that the mortality of non-native trees from forest ecosystems increased water content of surface soils, due primarily to a slower rate of decrease in soil water content during dry periods. Copyright © 2015 Elsevier B.V. All rights reserved.

Polyphenol content and antioxidant properties of colored soybean seeds from central Europe.

PubMed

Malenčić, Djordje; Cvejić, Jelena; Miladinović, Jegor

2012-01-01

The antioxidant activity and contents of various polyphenol classes in the seeds of seven soybean varieties of different seed color and one yellow seed cultivar, representing a reference genotype, were evaluated. Total polyphenols and tannins were determined after extraction of plant material with 70% aqueous acetone, and total flavonoids were extracted with methanol and acetic acid, whereas anthocyanins were extracted with 20% aqueous ethanol. In addition, isoflavone content and composition were determined using high-performance liquid chromatography analysis. Antioxidant activity of seed extracts was evaluated by the 2,2-diphenyl-1-picrylhydrazyl free radical scavenging activity assay. A positive linear correlation between antioxidant activity and contents of total polyphenols and anthocyanins was established. The highest antioxidant activity was observed in the extracts of black and brown varieties, which also showed high levels of all polyphenol classes examined. Yellow seed had the highest total isoflavone content (3.62 mg/g of dry material). The highest concentration of total daidzein was determined in black seeds (>2.0 mg/g of dry material), and the highest total glycitein and genistein contents occurred in the yellow cultivar (0.53 and 1.49 mg/g of dry material, respectively). According to our results, varieties of black and brown seeds could be of special interest not only for their large content of total polyphenols, ranging from 4.94 to 6.22 mg of gallic acid equivalents/g of dry material, but also for their high content of natural antioxidants such as anthocyanins.