Olkiluoto 1 and 2 - Plant efficiency improvement and lifetime extension-project (PELE) implemented during outages 2010 and 2011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kosonen, M.; Hakola, M.

2012-07-01

Teollisuuden Voima Oyj (TVO) is a non-listed public company founded in 1969 to produce electricity for its stakeholders. TVO is the operator of the Olkiluoto nuclear power plant. TVO follows the principle of continuous improvement in the operation and maintenance of the Olkiluoto plant units. The PELE project (Plant Efficiency Improvement and Lifetime Extension), mainly completed during the annual outages in 2010 and 2011, and forms one part of the systematic development of Olkiluoto units. TVO maintains a long-term development program that aims at systematically modernizing the plant unit systems and equipment based on the latest technology. According to themore » program, the Olkiluoto 1 and Olkiluoto 2 plant units are constantly renovated with the intention of keeping them safe and reliable, The aim of the modernization projects is to improve the safety, reliability, and performance of the plant units. PELE project at Olkiluoto 1 was done in 2010 and at Olkiluoto 2 in 2011. The outage length of Olkiluoto 1 was 26 d 12 h 4 min and Olkiluoto 2 outage length was 28 d 23 h 46 min. (Normal service-outage is about 14 days including refueling and refueling-outage length is about seven days. See figure 1) The PELE project consisted of several single projects collected into one for coordinated project management. Some of the main projects were as follows: - Low pressure turbines: rotor, stator vane, casing and turbine instrumentation replacement. - Replacement of Condenser Cooling Water (later called seawater pumps) pumps - Replacement of inner isolation valves on the main steam lines. - Generator and the generator cooling system replacement. - Low voltage switchgear replacement. This project will continue during future outages. PELE was a success. 100 TVO employees and 1500 subcontractor employees participated in the project. The execution of the PELE projects went extremely well during the outages. The replacement of the low pressure turbines and seawater pumps improved the efficiency of the plant units, and a power increase of nearly 20 MW was achieved at both plant units. PELE wonderfully manifests one of the strategic goals of our company; developing the competence of our in-house personnel by working in projects. (authors)« less

Continuous tooth generation in mouse is induced by activated epithelial Wnt/β-catenin signaling

PubMed Central

Järvinen, Elina; Salazar-Ciudad, Isaac; Birchmeier, Walter; Taketo, Makoto M.; Jernvall, Jukka; Thesleff, Irma

2006-01-01

The single replacement from milk teeth to permanent teeth makes mammalian teeth different from teeth of most nonmammalian vertebrates and other epithelial organs such as hair and feathers, whose continuous replacement has been linked to Wnt signaling. Here we show that mouse tooth buds expressing stabilized β-catenin in epithelium give rise to dozens of teeth. The molar crowns, however, are typically simplified unicusped cones. We demonstrate that the supernumerary teeth develop by a renewal process where new signaling centers, the enamel knots, bud off from the existing dental epithelium. The basic aspects of the unlocked tooth renewal can be reproduced with a computer model on tooth development by increasing the intrinsic level of activator production, supporting the role of β-catenin pathway as an upstream activator of enamel knot formation. These results may implicate Wnt signaling in tooth renewal, a capacity that was all but lost when mammals evolved progressively more complicated tooth shapes. PMID:17121988

Advances in repairing the degenerate retina by rod photoreceptor transplantation☆

PubMed Central

Pearson, Rachael A.

2014-01-01

Despite very different aetiologies, age-related macular degeneration (AMD) and most inherited retinal disorders culminate in the same final common pathway, loss of the light-sensitive photoreceptors. There are few clinical treatments and none can reverse the loss of vision. Photoreceptor replacement by transplantation is proposed as a broad treatment strategy applicable to all degenerations. The past decade has seen a number of landmark achievements in this field, which together provide strong justification for continuing investigation into photoreceptor replacement strategies. These include proof of principle for restoring vision by rod-photoreceptor transplantation in mice with congenital stationary night blindness and advances in stem cell biology, which have led to the generation of complete optic structures in vitro from embryonic stem cells. The latter represents enormous potential for generating suitable and renewable donor cells with which to achieve the former. However, there are still challenges presented by the degenerating recipient retinal environment that must be addressed as we move to translating these technologies towards clinical application. PMID:24412415

Actual operation and regulatory activities on steam generator replacement in Japan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saeki, Hitoshi

1997-02-01

This paper summarizes the operating reactors in Japan, and the status of the steam generators in these plants. It reviews plans for replacement of existing steam generators, and then goes into more detail on the planning and regulatory steps which must be addressed in the process of accomplishing this maintenance. The paper also reviews the typical steps involved in the process of removal and replacement of steam generators.

Spanish Pacemaker Registry. Twelfth Official Report of the Spanish Society of Cardiology Working Group on Cardiac Pacing (2014).

PubMed

Cano Pérez, Óscar; Pombo Jiménez, Marta; Coma Samartín, Raúl

2015-12-01

This report describes the results of the analysis of pacemaker implant and replacement data submitted to the Spanish Pacemaker Registry in 2014, with special reference to pacing mode selection. The report is based on the processing of information provided by the European Pacemaker Patient Identification Card. Information was received from 117 hospitals, with a total of 12 358 cards, representing 34% of estimated activity. Use of conventional generators and resynchronization devices was 784 and 64.4 units per million population, respectively. The mean age of patients receiving an implant was 77.3 years. Men received 59% of implants and 56.4% of replacements. Most patients receiving generator implants and replacements were in the age range 80 to 89 years. Most endocardial leads used were bipolar, and 84.2% had an active fixation system. Pacing was in VVI/R mode despite being in sinus rhythm in 24.7% of patients with sick sinus syndrome and 24% of those with atrioventricular block. The use of pacemaker generators and resynchronization devices per million population continued to increase. Most implanted leads had active fixation and approximately 20% had magnetic resonance imaging protection. Age and sex directly influenced pacing mode selection, which could have been improved in more than 20% of cases. Copyright © 2015 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

Complex patterns of tooth replacement revealed in the fruit bat (Eidolon helvum).

PubMed

Popa, Elena M; Anthwal, Neal; Tucker, Abigail S

2016-12-01

How teeth are replaced during normal growth and development has long been an important question for comparative and developmental anatomy. Non-standard model animals have become increasingly popular in this field due to the fact that the canonical model laboratory mammal, the mouse, develops only one generation of teeth (monophyodonty), whereas the majority of mammals possess two generations of teeth (diphyodonty). Here we used the straw-coloured fruit bat (Eidolon helvum), an Old World megabat, which has two generations of teeth, in order to observe the development and replacement of tooth germs from initiation up to mineralization stages. Our morphological study uses 3D reconstruction of histological sections to uncover differing arrangements of the first and second-generation tooth germs during the process of tooth replacement. We show that both tooth germ generations develop as part of the dental lamina, with the first generation detaching from the lamina, leaving the free edge to give rise to a second generation. This separation was particularly marked at the third premolar locus, where the primary and replacement teeth become positioned side by side, unconnected by a lamina. The position of the replacement tooth, with respect to the primary tooth, varied within the mouth, with replacements forming posterior to or directly lingual to the primary tooth. Development of replacement teeth was arrested at some tooth positions and this appeared to be linked to the timing of tooth initiation and the subsequent rate of development. This study adds an additional species to the growing body of non-model species used in the study of tooth replacement, and offers a new insight into the development of the diphyodont condition. © 2016 Anatomical Society.

Highly stable aerosol generator

DOEpatents

DeFord, H.S.; Clark, M.L.

1981-11-03

An improved compressed air nebulizer has been developed such that a uniform aerosol particle size and concentration may be produced over long time periods. This result is achieved by applying a vacuum pressure to the makeup assembly and by use of a vent tube between the atmosphere and the makeup solution. By applying appropriate vacuum pressures to the makeup solution container and by proper positioning of the vent tube, a constant level of aspirating solution may be maintained within the aspirating assembly with aspirating solution continuously replaced from the makeup solution supply. This device may also be adapted to have a plurality of aerosol generators and only one central makeup assembly. 2 figs.

Highly stable aerosol generator

DOEpatents

DeFord, Henry S.; Clark, Mark L.

1981-01-01

An improved compressed air nebulizer has been developed such that a uniform aerosol particle size and concentration may be produced over long time periods. This result is achieved by applying a vacuum pressure to the makeup assembly and by use of a vent tube between the atmosphere and the makeup solution. By applying appropriate vacuum pressures to the makeup solution container and by proper positioning of the vent tube, a constant level of aspirating solution may be maintained within the aspirating assembly with aspirating solution continuously replaced from the makeup solution supply. This device may also be adapted to have a plurality of aerosol generators and only one central makeup assembly.

Common developmental pathways link tooth shape to regeneration

PubMed Central

Fraser, Gareth J.; Bloomquist, Ryan F.; Streelman, J. Todd

2013-01-01

In many non-mammalian vertebrates, adult dentitions result from cyclical rounds of tooth regeneration wherein simple unicuspid teeth are replaced by more complex forms. Therefore and by contrast to mammalian models, the numerical majority of vertebrate teeth develop shape during the process of replacement. Here, we exploit the dental diversity of Lake Malawi cichlid fishes to ask how vertebrates generally replace their dentition and in turn how this process acts to influence resulting tooth morphologies. First, we used immunohistochemistry to chart organogenesis of continually replacing cichlid teeth and discovered an epithelial down-growth that initiates the replacement cycle via a labial proliferation bias. Next, we identified sets of co-expressed genes from common pathways active during de novo, lifelong tooth replacement and tooth morphogenesis. Of note, we found two distinct epithelial cell populations, expressing markers of dental competence and cell potency, which may be responsible for tooth regeneration. Related gene sets were simultaneously active in putative signaling centers associated with the differentiation of replacement teeth with complex shapes. Finally, we manipulated targeted pathways (BMP, FGF, Hh, Notch, Wnt/β-catenin) in vivo with small molecules and demonstrated dose-dependent effects on both tooth replacement and tooth shape. Our data suggest that the processes of tooth regeneration and tooth shape morphogenesis are integrated via a common set of molecular signals. This linkage has subsequently been lost or decoupled in mammalian dentitions where complex tooth shapes develop in first generation dentitions that lack the capacity for lifelong replacement. Our dissection of the molecular mechanics of vertebrate tooth replacement coupled to complex shape pinpoints aspects of odontogenesis that might be re-evolved in the lab to solve problems in regenerative dentistry. PMID:23422830

Project Execution Plan for the Remote Handled Low-Level Waste Disposal Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Danny Anderson

2014-07-01

As part of ongoing cleanup activities at the Idaho National Laboratory (INL), closure of the Radioactive Waste Management Complex (RWMC) is proceeding under the Comprehensive Environmental Response, Compensation, and Liability Act (42 USC 9601 et seq. 1980). INL-generated radioactive waste has been disposed of at RWMC since 1952. The Subsurface Disposal Area (SDA) at RWMC accepted the bulk of INL’s contact and remote-handled low-level waste (LLW) for disposal. Disposal of contact-handled LLW and remote-handled LLW ion-exchange resins from the Advanced Test Reactor in the open pit of the SDA ceased September 30, 2008. Disposal of remote-handled LLW in concrete disposalmore » vaults at RWMC will continue until the facility is full or until it must be closed in preparation for final remediation of the SDA (approximately at the end of fiscal year FY 2017). The continuing nuclear mission of INL, associated ongoing and planned operations, and Naval spent fuel activities at the Naval Reactors Facility (NRF) require continued capability to appropriately dispose of contact and remote handled LLW. A programmatic analysis of disposal alternatives for contact and remote-handled LLW generated at INL was conducted by the INL contractor in Fiscal Year 2006; subsequent evaluations were completed in Fiscal Year 2007. The result of these analyses was a recommendation to the Department of Energy (DOE) that all contact-handled LLW generated after September 30, 2008, be disposed offsite, and that DOE proceed with a capital project to establish replacement remote-handled LLW disposal capability. An analysis of the alternatives for providing replacement remote-handled LLW disposal capability has been performed to support Critical Decision-1. The highest ranked alternative to provide this required capability has been determined to be the development of a new onsite remote-handled LLW disposal facility to replace the existing remote-handled LLW disposal vaults at the SDA. Several offsite DOE and commercial disposal options exist for contact-handled LLW; however, offsite disposal options are either not currently available (i.e., commercial disposal facilities), practical, or cost-effective for all remote-handled LLW streams generated at INL. Offsite disposal of all INL and tenant-generated remote-handled waste is further complicated by issues associated with transporting highly radioactive waste in commerce; and infrastructure and processing changes at the generating facilities, specifically NRF, that would be required to support offsite disposal. The INL Remote-Handled LLW Disposal Project will develop a new remote handled LLW disposal facility to meet mission-critical, remote-handled LLW disposal needs. A formal DOE decision to proceed with the project has been made in accordance with the requirements of National Environmental Policy Act (42 USC§ 4321 et seq.). Remote-handled LLW is generated from nuclear programs conducted at INL, including spent nuclear fuel handling and operations at NRF and operations at the Advanced Test Reactor. Remote-handled LLW also will be generated by new INL programs and from segregation and treatment (as necessary) of remote handled scrap and waste currently stored in the Radioactive Scrap and Waste Facility at the Materials and Fuels Complex.« less

Next-generation pushbroom filter radiometers for remote sensing

NASA Astrophysics Data System (ADS)

Tarde, Richard W.; Dittman, Michael G.; Kvaran, Geir E.

2012-09-01

Individual focal plane size, yield, and quality continue to improve, as does the technology required to combine these into large tiled formats. As a result, next-generation pushbroom imagers are replacing traditional scanning technologies in remote sensing applications. Pushbroom architecture has inherently better radiometric sensitivity and significantly reduced payload mass, power, and volume than previous generation scanning technologies. However, the architecture creates challenges achieving the required radiometric accuracy performance. Achieving good radiometric accuracy, including image spectral and spatial uniformity, requires creative optical design, high quality focal planes and filters, careful consideration of on-board calibration sources, and state-of-the-art ground test facilities. Ball Aerospace built the Landsat Data Continuity Mission (LDCM) next-generation Operational Landsat Imager (OLI) payload. Scheduled to launch in 2013, OLI provides imagery consistent with the historical Landsat spectral, spatial, radiometric, and geometric data record and completes the generational technology upgrade from the Enhanced Thematic Mapper (ETM+) whiskbroom technology to modern pushbroom technology afforded by advanced focal planes. We explain how Ball's capabilities allowed producing the innovative next-generational OLI pushbroom filter radiometer that meets challenging radiometric accuracy or calibration requirements. OLI will improve the multi-decadal land surface observation dataset dating back to the 1972 launch of ERTS-1 or Landsat 1.

Complications from prophylactic replacement of cardiac implantable electronic device generators in response to United States Food and Drug Administration recall: A systematic review and meta-analysis.

PubMed

Zeitler, Emily P; Patel, Divyang; Hasselblad, Vic; Sanders, Gillian D; Al-Khatib, Sana M

2015-07-01

The number of cardiac implantable electronic device (CIED) recalls and advisories has increased over the past 3 decades, yet no consensus exists on how to best manage patients with these CIEDs, partially because rates of complications from prophylactic replacement are unknown. The purpose of this study was to establish rates of complications when recalled CIED generators are replaced prophylactically. We searched MEDLINE and the Cochrane Controlled Trials Register for reports of prophylactic replacement of recalled CIED generators. Studies with <20 subjects were excluded. We then conducted a meta-analysis of qualifying studies to determine the rates of combined major complications, mortality, and reoperation. We identified 7 citations that met our inclusion criteria and reported ≥1 end-points of interest. Four were single center, and 3 were multicenter. Six studies collected data retrospectively (n = 1213) and 1 prospectively (n = 222). Using a random effects model to combine data from all included studies, the rate of major complications was 2.5% (95% confidence interval [CI] 1.0%-4.5%). Combining data from 6 studies reporting mortality and reoperation, the rates were 0.5% (95% CI 0.1%-0.9%) and 2.5% (95% CI 0.8%-4.5%), respectively. Prophylactic replacement of recalled CIED generators is associated with a low mortality rate but nontrivial rates of other major complications similar to those reported when CIED generators are replaced for other reasons. Thus, when considering replacing a recalled CIED generator, known risks of elective generator replacement likely apply and can be weighed against risks associated with device failure. Copyright © 2015 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Exhausted implanted pulse generator in sacral nerve stimulation for faecal incontinence: What next in daily practice for patients?

PubMed

Duchalais, Emilie; Meurette, Guillaume; Perrot, Bastien; Wyart, Vincent; Kubis, Caroline; Lehur, Paul-Antoine

2016-02-01

The efficacy of sacral nerve stimulation in faecal incontinence relies on an implanted pulse generator known to have a limited lifespan. The long-term use of sacral nerve stimulation raises concerns about the true lifespan of generators. The aim of the study was to assess the lifespan of sacral nerve stimulation implanted pulse generators in daily practice, and the outcome of exhausted generator replacement, in faecal incontinent patients. Faecal incontinent patients with pulse generators (Medtronic Interstim™ or InterstimII™) implanted in a single centre from 2001 to 2014 were prospectively followed up. Generator lifespan was measured according to the Kaplan-Meier method. Patients with a generator explanted/turned off before exhaustion were excluded. Morbidity of exhausted generator replacement and the outcome (Cleveland Clinic Florida Faecal Incontinence (CCF-FI) and Faecal Incontinence Quality of Life (FIQL) scores) were recorded. Of 135 patients with an implanted pulse generator, 112 (InterstimII 66) were included. Mean follow-up was 4.9 ± 2.8 years. The generator reached exhaustion in 29 (26%) cases. Overall median lifespan of an implanted pulse generator was approximately 9 years (95% CI 8-9.2). Interstim and InterstimII 25th percentile lifespan was 7.2 (CI 6.4-8.3) and 5 (CI 4-not reached) years, respectively. After exhaustion, generators were replaced, left in place or explanted in 23, 2 and 4 patients, respectively. Generator replacement was virtually uneventful. CCF-FI/FIQL scores remained unchanged after generator replacement (CCF-FI 8 ± 2 vs 7 ± 3; FIQL 3 ± 0.6 vs 3 ± 0.5; p = ns). In this study, the implanted pulse generator observed median lifespan was 9 years. After exhaustion, generators were safely and efficiently replaced. The study also gives insight into long-term needs and costs of sacral nerve stimulation (SNS) therapy.

Effect of growth solution, membrane size and array connection on microbial fuel cell power supply for medical devices.

PubMed

Roxby, Daniel N; Nham Tran; Pak-Lam Yu; Nguyen, Hung T

2016-08-01

Implanted biomedical devices typically last a number of years before their batteries are depleted and a surgery is required to replace them. A Microbial Fuel Cell (MFC) is a device which by using bacteria, directly breaks down sugars to generate electricity. Conceptually there is potential to continually power implanted medical devices for the lifetime of a patient. To investigate the practical potential of this technology, H-Cell Dual Chamber MFCs were evaluated with two different growth solutions and measurements recorded for maximum power output both of individual MFCs and connected MFCs. Using Luria-Bertani media and connecting MFCs in a hybrid series and parallel arrangement with larger membrane sizes showed the highest power output and the greatest potential for replacing implanted batteries.

Pharmacokinetics and Pharmacodynamics of Piperacillin-Tazobactam in 42 Patients Treated with Concomitant CRRT

PubMed Central

Bauer, Seth R.; Salem, Charbel; Connor, Michael J.; Groszek, Joseph; Taylor, Maria E.; Wei, Peilin; Tolwani, Ashita J.

2012-01-01

Summary Background and objectives Current recommendations for piperacillin-tazobactam dosing in patients receiving continuous renal replacement therapy originate from studies with relatively few patients and lower continuous renal replacement therapy doses than commonly used today. This study measured the pharmacokinetic and pharmacodynamic characteristics of piperacillin-tazobactam in patients treated with continuous renal replacement therapy using contemporary equipment and prescriptions. Design, setting, participants, & measurements A multicenter prospective observational study in the intensive care units of two academic medical centers was performed, enrolling patients with AKI or ESRD receiving piperacillin-tazobactam while being treated with continuous renal replacement therapy. Pregnant women, children, and patients with end stage liver disease were excluded from enrollment. Plasma and continuous renal replacement therapy effluent samples were analyzed for piperacillin and tazobactam levels using HPLC. Pharmacokinetic and pharmacodynamic parameters were calculated using standard equations. Multivariate analyses were used to examine the association of patient and continuous renal replacement therapy characteristics with piperacillin pharmacokinetic parameters. Results Forty-two of fifty-five subjects enrolled had complete sampling. Volume of distribution (median=0.38 L/kg, intraquartile range=0.20 L/kg) and elimination rate constants (median=0.104 h−1, intraquartile range=0.052 h−1) were highly variable, and clinical parameters could explain only a small fraction of the large variability in pharmacokinetic parameters. Probability of target attainment for piperacillin was 83% for total drug but only 77% when the unbound fraction was considered. Conclusions There is significant patient to patient variability in pharmacokinetic/pharmacodynamic parameters in patients receiving continuous renal replacement therapy. Many patients did not achieve pharmacodynamic targets, suggesting that therapeutic drug monitoring might optimize therapy. PMID:22282479

NARC Rayon Replacement Program for the Space Shuttle Reusable Solid Rocket Motor Nozzle: Screening Summary

NASA Technical Reports Server (NTRS)

Cook, R. V.; Fairbourn, M. W.; Wendel, G. M.

2000-01-01

Thiokol Corporation and NASA MSFC are jointly developing a replacement for North American Rayon Corporation (NARC) Aerospace Grade Rayon (1650/720 continuous filament), the precursor for the Carbon Cloth Phenolic (CCP) ablatives used in the Space Shuttle Reusable Solid Rocket Motor (RSRM) Nozzles. NARC discontinued production of Aerospace Grade Rayon in September 1997. NASA maintains a stockpile of NARC Rayon to support RSRM production through the summer of 2005. The program plan for selection and qualification of a replacement for NARC rayon was approved in August 1998. Screening activities began in February 1999. The intent of this paper is to provide a summary of the data generated during the screening phase of the NARC Rayon Replacement Program. Twelve cellulose based fibers (rayon and lyocell) were evaluated. These fibers were supplied by three independent vendors. Many of these fibers were carbonized by two independent carbonizers. Each candidate was tested according to standard acceptance test methods at each step of the manufacturing process. Additional testing was performed with the candidate CCPS, including hot fire tests, Process studies and mechanical and thermal characterization. Six of the twelve fiber candidates tested were dropped at the conclusion of Phase 1. The reasons for the elimination of these candidates included; difficulties in processing the material in the whitegoods, carbon and CCP forms; poor composite mechanical performance; and future availability concerns. The remaining six fibers demonstrated enough promise to merit continued evaluation and optimization of the CCP fabrication process. Note: Certain CCP data falls under the restrictions of US export laws, (ITAR, etc.) and will not be included in this paper.

Hip or knee replacement - in the hospital after

MedlinePlus

Hip replacement surgery - after - self-care; Knee replacement surgery - after - self-care ... taking walks in the hallways with help. After knee replacement, some surgeons recommend using a continuous passive ...

NASA Space Shuttle Program: Shuttle Environmental Assurance (SEA) Initiative

NASA Technical Reports Server (NTRS)

Glover, Steve E.; McCool, Alex (Technical Monitor)

2002-01-01

The first Space Shuttle flight was in 1981 and the fleet was originally expected to be replaced with a new generation vehicle in the early 21st century. Space Shuttle Program (SSP) elements proactively address environmental and obsolescence concerns and continue to improve safety and supportability. The SSP manager created the Shuttle Environmental Assurance (SEA) Initiative in 2000. SEA is to provide an integrated approach for the SSP to promote environmental excellence, proactively manage materials obsolescence, and optimize associated resources.

A new multiprogrammable isotopic powered cardiac pacemaker

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smyth, N.P.; Purdy, D.L.; Sager, D.

1982-09-01

A new multiprogrammable, isotopic-powered cardiac pacemaker was implanted in six patients as a custom device. Five were initial implants and one was a replacement. The patients were studied for up to two years. In five of the six cases it was found advantageous to change one of the programmable parameters. Multiprogrammability is obviously as important in an isotopic pulse generator as in a lithium unit, if not more so, because of the unit's greater longevity. Further studies are continuing in an FDA approved clinical trial.

Journal of Rehabilitation Research and Development Progress Reports 1994, Volume 32, June 1995

DTIC Science & Technology

1995-06-01

Stepping Over an Obstacle: Effect of Reduced Visual Field 50 Effect of Reduced Optic Flow on Gait 51 Effects of Robotic-Assisted Weight Support on Gait...Geometry in Hip Replacement 240 Wear Debris Generation in Hip Modular Head and Neck Components 241 Changes in Bone Blood Flow Associated with...rectangular cross-section to form a continuously flowing ribbon of melted plastic. Rib- bon dimensions are 0.75 mm thick and 5 mm wide, corresponding to

Advances in repairing the degenerate retina by rod photoreceptor transplantation.

PubMed

Pearson, Rachael A

2014-01-01

Despite very different aetiologies, age-related macular degeneration (AMD) and most inherited retinal disorders culminate in the same final common pathway, loss of the light-sensitive photoreceptors. There are few clinical treatments and none can reverse the loss of vision. Photoreceptor replacement by transplantation is proposed as a broad treatment strategy applicable to all degenerations. The past decade has seen a number of landmark achievements in this field, which together provide strong justification for continuing investigation into photoreceptor replacement strategies. These include proof of principle for restoring vision by rod-photoreceptor transplantation in mice with congenital stationary night blindness and advances in stem cell biology, which have led to the generation of complete optic structures in vitro from embryonic stem cells. The latter represents enormous potential for generating suitable and renewable donor cells with which to achieve the former. However, there are still challenges presented by the degenerating recipient retinal environment that must be addressed as we move to translating these technologies towards clinical application. Copyright © 2014 The Author. Published by Elsevier Inc. All rights reserved.

Cells adapted to the proteasome inhibitor 4-hydroxy- 5-iodo-3-nitrophenylacetyl-Leu-Leu-leucinal-vinyl sulfone require enzymatically active proteasomes for continued survival.

PubMed

Princiotta, M F; Schubert, U; Chen, W; Bennink, J R; Myung, J; Crews, C M; Yewdell, J W

2001-01-16

The proteasome is the primary protease used by cells for degrading proteins and generating peptide ligands for class I molecules of the major histocompatibility complex. Based on the properties of cells adapted to grow in the presence of the proteasome inhibitor 4-hydroxy-5-iodo-3-nitrophenylacetyl-Leu-Leu-leucinal-vinyl sulfone (NLVS), it was proposed that proteasomes can be replaced by alternative proteolytic systems, particularly a large proteolytic complex with a tripeptidyl peptidase II activity. Here we show that NLVS-adapted cells retain sensitivity to a number of highly specific proteasome inhibitors with regard to antigenic peptide generation, accumulation of polyubiquitinated proteins, degradation of p53, and cell viability. In addition, we show that in the same assays (with a single minor exception), NLVS-adapted cells are about as sensitive as nonselected cells to Ala-Ala-Phe-chloromethylketone, a specific inhibitor of tripeptidyl peptidase II activity. Based on these findings, we conclude that proteasomes still have essential proteolytic functions in adapted cells that are not replaced by Ala-Ala-Phe-chloromethylketone-sensitive proteases.

Ultrasonic filtration of industrial chemical solutions

NASA Technical Reports Server (NTRS)

Cosma, T.

1974-01-01

The practical results obtained as a result of filtering industrial chemical solutions under continuous flow conditions with the aid of an ultrasonic filter are presented. The main part of the assembly consists of an ultrasonic generator with an output power of about 400 W and the filtration assembly, in which there is a magnetostrictive amplifier constructed for 20.5 kHz. In addition to ensuring a continuous flow of filtered solution, ultrasonic filters can be replaced or cleaned at intervals of time that are 8-10 times greater than in the case of mechanical filters. They yield considerably better results as far as the size of the filtered particles is concerned. The parameters on which filtration quality depends are also presented.

I-deas TMG to NX Space Systems Thermal Model Conversion and Computational Performance Comparison

NASA Technical Reports Server (NTRS)

Somawardhana, Ruwan

2011-01-01

CAD/CAE packages change on a continuous basis as the power of the tools increase to meet demands. End -users must adapt to new products as they come to market and replace legacy packages. CAE modeling has continued to evolve and is constantly becoming more detailed and complex. Though this comes at the cost of increased computing requirements Parallel processing coupled with appropriate hardware can minimize computation time. Users of Maya Thermal Model Generator (TMG) are faced with transitioning from NX I -deas to NX Space Systems Thermal (SST). It is important to understand what differences there are when changing software packages We are looking for consistency in results.

Programmable Pulse Generator for Aditya Gas Puffing System

NASA Astrophysics Data System (ADS)

Patel, Narendra; Chavda, Chhaya; Bhatt, S. B.; Chattopadhyay, Prabal; Saxena, Y. C.

2012-11-01

In the Aditya Tokamak, one of primary requirement for plasma generation is to feed the required quantity of the fuel gas prior to plasma shot. Gas feed system mainly consists of piezoelectric gas leak valve and gas reservoir. The Hydrogen gas is prior to 300ms loop voltage for the duration of 4 msec to 7 msec. Gas is puffed during the shot for required plasma parameters and to increase plasma density using the same system. The valve is controlled by either continuous voltage or pulses of different width, amplitude and delay with respect to loop voltage. These voltage pulses are normally applied through standard pulse generator. The standard pulse generator is replaced by micro controller based in housed developed programmable pulse generator system consists of in built power supply, BNC input for external trigger, BNC output and serial interface. This programmable pulse generator is successfully tested and is in operation for gas puffing during ADITYA Tokamak experiments. The paper discusses the design and development aspect of the system.

40 CFR Appendix A to Subpart F of... - List of Qualified Energy Conservation Measures, Qualified Renewable Generation, and Measures...

Code of Federal Regulations, 2010 CFR

2010-07-01

... replacements • Customer located power generation based on photovoltaic, solar thermal, biomass, wind or geothermal resources • Swimming pool pump replacements • Gasket replacements • Maintenance/coil cleaning 1... photovoltaic, solar thermal, biomass, wind, and geothermal resources • Energy efficient office equipment...

40 CFR Appendix A to Subpart F of... - List of Qualified Energy Conservation Measures, Qualified Renewable Generation, and Measures...

Code of Federal Regulations, 2012 CFR

2012-07-01

... replacements • Customer located power generation based on photovoltaic, solar thermal, biomass, wind or geothermal resources • Swimming pool pump replacements • Gasket replacements • Maintenance/coil cleaning 1... photovoltaic, solar thermal, biomass, wind, and geothermal resources • Energy efficient office equipment...

40 CFR Appendix A to Subpart F of... - List of Qualified Energy Conservation Measures, Qualified Renewable Generation, and Measures...

Code of Federal Regulations, 2011 CFR

2011-07-01

... replacements • Customer located power generation based on photovoltaic, solar thermal, biomass, wind or geothermal resources • Swimming pool pump replacements • Gasket replacements • Maintenance/coil cleaning 1... photovoltaic, solar thermal, biomass, wind, and geothermal resources • Energy efficient office equipment...

40 CFR Appendix A to Subpart F of... - List of Qualified Energy Conservation Measures, Qualified Renewable Generation, and Measures...

Code of Federal Regulations, 2014 CFR

2014-07-01

... replacements • Customer located power generation based on photovoltaic, solar thermal, biomass, wind or geothermal resources • Swimming pool pump replacements • Gasket replacements • Maintenance/coil cleaning 1... photovoltaic, solar thermal, biomass, wind, and geothermal resources • Energy efficient office equipment...

40 CFR Appendix A to Subpart F of... - List of Qualified Energy Conservation Measures, Qualified Renewable Generation, and Measures...

Code of Federal Regulations, 2013 CFR

2013-07-01

... replacements • Customer located power generation based on photovoltaic, solar thermal, biomass, wind or geothermal resources • Swimming pool pump replacements • Gasket replacements • Maintenance/coil cleaning 1... photovoltaic, solar thermal, biomass, wind, and geothermal resources • Energy efficient office equipment...

75 FR 28506 - Airworthiness Directives; Hawker Beechcraft Corporation (Type Certificate No. A00010WI Previously...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-21

... installation of certain serial number (S/N) starter generators and replacing the starter generator if one with an affected serial number is found. This proposed AD results from reports that starter generators... proposing this AD to detect and replace starter generators with defective armature insulating materials...

75 FR 52235 - Airworthiness Directives; Hawker Beechcraft Corporation (Type Certificate No. A00010WI Previously...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-25

... certain serial number (S/N) starter generators and replace the starter generator if one with an affected serial number is found. This AD results from reports that starter generators with deficient armature... replace starter generators with defective armature insulating materials. This condition could result in...

Wnt signaling during tooth replacement in zebrafish (Danio rerio): pitfalls and perspectives

PubMed Central

Huysseune, Ann; Soenens, Mieke; Elderweirdt, Fien

2014-01-01

The canonical (β-catenin dependent) Wnt signaling pathway has emerged as a likely candidate for regulating tooth replacement in continuously renewing dentitions. So far, the involvement of canonical Wnt signaling has been experimentally demonstrated predominantly in amniotes. These studies tend to show stimulation of tooth formation by activation of the Wnt pathway, and inhibition of tooth formation when blocking the pathway. Here, we report a strong and dynamic expression of the soluble Wnt inhibitor dickkopf1 (dkk1) in developing zebrafish (Danio rerio) tooth germs, suggesting an active repression of Wnt signaling during morphogenesis and cytodifferentiation of a tooth, and derepression of Wnt signaling during start of replacement tooth formation. To further analyse the role of Wnt signaling, we used different gain-of-function approaches. These yielded disjunct results, yet none of them indicating enhanced tooth replacement. Thus, masterblind (mbl) mutants, defective in axin1, mimic overexpression of Wnt, but display a normally patterned dentition in which teeth are replaced at the appropriate times and positions. Activating the pathway with LiCl had variable outcomes, either resulting in the absence, or the delayed formation, of first-generation teeth, or yielding a regular dentition with normal replacement, but no supernumerary teeth or accelerated tooth replacement. The failure so far to influence tooth replacement in the zebrafish by perturbing Wnt signaling is discussed in the light of (i) potential technical pitfalls related to dose- or time-dependency, (ii) the complexity of the canonical Wnt pathway, and (iii) species-specific differences in the nature and activity of pathway components. Finally, we emphasize the importance of in-depth knowledge of the wild-type pattern for reliable interpretations. It is hoped that our analysis can be inspiring to critically assess and elucidate the role of Wnt signaling in tooth development in polyphyodonts. PMID:25339911

Mechanism of action of additives in chemical vapor generation of hydrogen selenide: Iodide and thiocyanate

NASA Astrophysics Data System (ADS)

Pitzalis, Emanuela; Onor, Massimo; Spiniello, Roberto; Braz, Carlos Eduardo Mendes; D'Ulivo, Alessandro

2018-07-01

The chemical vapor generation of H2Se has been investigated in the presence and in the absence of either NaI or NaSCN as additives (0.5 mol L-1), in HClO4 media (0.1-5.0 mol L-1) and using a low concentration of NaBH4 (0.02 mol L-1). The enhancement of generation efficiency of H2Se produced by iodide and thiocyanate was measured by a continuous flow reaction system coupled with a miniature argon‑hydrogen diffusion flame and atomic absorption detection. The chemifold of the continuous flow reactor was designed in order to change the mixing sequence and the interaction time of the reagents. By this way it has been possible to evaluate the contribution of additive‑selenium and additive-borane species to the mechanism producing the increase of generation efficiency of H2Se. Both the iodide complexes of selenium and borane contribute to enhance generation efficiency of H2Se, whereas the thiocyanate complexes of selenium rather than thiocyanate-borane complexes play a major role in the enhancement of the efficiency. At elevated acidities (2 < [H+] < 5 mol L-1), only thiocyanate continues to maintain its properties to increase H2Se generation efficiency while iodide causes a marked signal depression unless its addition is performed after the starting of SeIV- [BH4-] reaction with an appropriate time delay. Both iodide and thiocyanate caused marked depression of H2Se generation when NaBH4 was replaced by the amine boranes, NH3-BH3 and tert-ButylNH2-BH3.

Continuous renal replacement therapies: a brief primer for the neurointensivist.

PubMed

Patel, Pritesh; Nandwani, Veena; McCarthy, Paul J; Conrad, Steven A; Keith Scott, L

2010-10-01

Continuous renal replacement therapy (CRRT) is a renal replacement modality that is often used in the ICU setting, including the neuro-ICU. This form of renal replacement therapy has been used classically for acute renal failure in patients with hemodynamic compromise, but is gaining acceptance as a method to control vascular and extra-vascular volume and mediate cytokines in non-renal diseases. Although these uses are briefly discussed, this review concentrates on the different forms of continuous renal replacement, mainly focusing on the technology of convective versus diffusive modalities and briefly on filter technology. There is also discussion on the various anticoagulation regimes used in CRRT including data on performing CRRT without anticoagulation. This review is not meant to be a discussion on the pros and cons of CRRT versus intermittent dialysis, but rather a primer on the technology of CRRT and how this therapy may affect general care of the ICU patient.

Automated speech understanding: the next generation

NASA Astrophysics Data System (ADS)

Picone, J.; Ebel, W. J.; Deshmukh, N.

1995-04-01

Modern speech understanding systems merge interdisciplinary technologies from Signal Processing, Pattern Recognition, Natural Language, and Linguistics into a unified statistical framework. These systems, which have applications in a wide range of signal processing problems, represent a revolution in Digital Signal Processing (DSP). Once a field dominated by vector-oriented processors and linear algebra-based mathematics, the current generation of DSP-based systems rely on sophisticated statistical models implemented using a complex software paradigm. Such systems are now capable of understanding continuous speech input for vocabularies of several thousand words in operational environments. The current generation of deployed systems, based on small vocabularies of isolated words, will soon be replaced by a new technology offering natural language access to vast information resources such as the Internet, and provide completely automated voice interfaces for mundane tasks such as travel planning and directory assistance.

High yield neutron generators using the DD reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vainionpaa, J. H.; Harris, J. L.; Piestrup, M. A.

2013-04-19

A product line of high yield neutron generators has been developed at Adelphi technology inc. The generators use the D-D fusion reaction and are driven by an ion beam supplied by a microwave ion source. Yields of up to 5 Multiplication-Sign 10{sup 9} n/s have been achieved, which are comparable to those obtained using the more efficient D-T reaction. The microwave-driven plasma uses the electron cyclotron resonance (ECR) to produce a high plasma density for high current and high atomic ion species. These generators have an actively pumped vacuum system that allows operation at reduced pressure in the target chamber,more » increasing the overall system reliability. Since no radioactive tritium is used, the generators can be easily serviced, and components can be easily replaced, providing essentially an unlimited lifetime. Fast neutron source size can be adjusted by selecting the aperture and target geometries according to customer specifications. Pulsed and continuous operation has been demonstrated. Minimum pulse lengths of 50 {mu}s have been achieved. Since the generators are easily serviceable, they offer a long lifetime neutron generator for laboratories and commercial systems requiring continuous operation. Several of the generators have been enclosed in radiation shielding/moderator structures designed for customer specifications. These generators have been proven to be useful for prompt gamma neutron activation analysis (PGNAA), neutron activation analysis (NAA) and fast neutron radiography. Thus these generators make excellent fast, epithermal and thermal neutron sources for laboratories and industrial applications that require neutrons with safe operation, small footprint, low cost and small regulatory burden.« less

High yield neutron generators using the DD reaction

NASA Astrophysics Data System (ADS)

Vainionpaa, J. H.; Harris, J. L.; Piestrup, M. A.; Gary, C. K.; Williams, D. L.; Apodaca, M. D.; Cremer, J. T.; Ji, Qing; Ludewigt, B. A.; Jones, G.

2013-04-01

A product line of high yield neutron generators has been developed at Adelphi technology inc. The generators use the D-D fusion reaction and are driven by an ion beam supplied by a microwave ion source. Yields of up to 5 × 109 n/s have been achieved, which are comparable to those obtained using the more efficient D-T reaction. The microwave-driven plasma uses the electron cyclotron resonance (ECR) to produce a high plasma density for high current and high atomic ion species. These generators have an actively pumped vacuum system that allows operation at reduced pressure in the target chamber, increasing the overall system reliability. Since no radioactive tritium is used, the generators can be easily serviced, and components can be easily replaced, providing essentially an unlimited lifetime. Fast neutron source size can be adjusted by selecting the aperture and target geometries according to customer specifications. Pulsed and continuous operation has been demonstrated. Minimum pulse lengths of 50 μs have been achieved. Since the generators are easily serviceable, they offer a long lifetime neutron generator for laboratories and commercial systems requiring continuous operation. Several of the generators have been enclosed in radiation shielding/moderator structures designed for customer specifications. These generators have been proven to be useful for prompt gamma neutron activation analysis (PGNAA), neutron activation analysis (NAA) and fast neutron radiography. Thus these generators make excellent fast, epithermal and thermal neutron sources for laboratories and industrial applications that require neutrons with safe operation, small footprint, low cost and small regulatory burden.

Meeting the challenge of food and energy security.

PubMed

Karp, Angela; Richter, Goetz M

2011-06-01

Growing crops for bioenergy or biofuels is increasingly viewed as conflicting with food production. However, energy use continues to rise and food production requires fuel inputs, which have increased with intensification. Focussing on the question of food or fuel is thus not helpful. The bigger, more pertinent, challenge is how the increasing demands for food and energy can be met in the future, particularly when water and land availability will be limited. Energy crop production systems differ greatly in environmental impact. The use of high-input food crops for liquid transport fuels (first-generation biofuels) needs to be phased out and replaced by the use of crop residues and low-input perennial crops (second/advanced-generation biofuels) with multiple environmental benefits. More research effort is needed to improve yields of biomass crops grown on lower grade land, and maximum value should be extracted through the exploitation of co-products and integrated biorefinery systems. Policy must continually emphasize the changes needed and tie incentives to improved greenhous gas reduction and environmental performance of biofuels.

Antibiotic Dosing in Continuous Renal Replacement Therapy.

PubMed

Shaw, Alexander R; Mueller, Bruce A

2017-07-01

Appropriate antibiotic dosing is critical to improve outcomes in critically ill patients with sepsis. The addition of continuous renal replacement therapy makes achieving appropriate antibiotic dosing more difficult. The lack of continuous renal replacement therapy standardization results in treatment variability between patients and may influence whether appropriate antibiotic exposure is achieved. The aim of this study was to determine if continuous renal replacement therapy effluent flow rate impacts attaining appropriate antibiotic concentrations when conventional continuous renal replacement therapy antibiotic doses were used. This study used Monte Carlo simulations to evaluate the effect of effluent flow rate variance on pharmacodynamic target attainment for cefepime, ceftazidime, levofloxacin, meropenem, piperacillin, and tazobactam. Published demographic and pharmacokinetic parameters for each antibiotic were used to develop a pharmacokinetic model. Monte Carlo simulations of 5000 patients were evaluated for each antibiotic dosing regimen at the extremes of Kidney Disease: Improving Global Outcomes guidelines recommended effluent flow rates (20 and 35 mL/kg/h). The probability of target attainment was calculated using antibiotic-specific pharmacodynamic targets assessed over the first 72 hours of therapy. Most conventional published antibiotic dosing recommendations, except for levofloxacin, reach acceptable probability of target attainment rates when effluent rates of 20 or 35 mL/kg/h are used. Copyright © 2017 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Delay in onset of metabolic alkalosis during regional citrate anti-coagulation in continuous renal replacement therapy with calcium-free replacement solution.

PubMed

See, Kay Choong; Lee, Margaret; Mukhopadhyay, Amartya

2009-01-01

Regional citrate anti-coagulation for continuous renal replacement therapy chelates calcium to produce the anti- coagulation effect. We hypothesise that a calcium-free replacement solution will require less citrate and produce fewer metabolic side effects. Fifty patients, in a Medical Intensive Care Unit of a tertiary teaching hospital (25 in each group), received continuous venovenous hemofiltration using either calcium-containing or calcium-free replacement solutions. Both groups had no significant differences in filter life, metabolic alkalosis, hypernatremia, hypocalcemia, and hypercalcemia. However, patients using calcium-containing solution developed metabolic alkalosis earlier, compared to patients using calcium-free solution (mean 24.6 hours,CI 0.8-48.4 vs. 37.2 hours, CI 9.4-65, P = 0.020). When calcium-containing replacement solution was used, more citrate was required (mean 280 ml/h, CI 227.2-332.8 vs. 265 ml/h, CI 203.4-326.6, P = 0.069), but less calcium was infused (mean 21.2 ml/h, CI 1.2-21.2 vs 51.6 ml/h, CI 26.8-76.4, P < or = 0.0001).

Stressful ethical issues in uremia therapy.

PubMed

Friedman, Eli A

2010-08-01

The objectives of this review are to introduce and explore the following representative ethical problems generated by modern renal replacement therapy: (1) reviewing the historical origin of medical ethics with specific reference to nephrology; (2) recognizing the complex stresses surrounding assignment of a deceased donor renal transplant to a geriatric patient while young patients continue waiting for a donor kidney; and (3) appreciating the concept of futility and support for a uremic patient opting for death rather than further uremia therapy as the best in choice in coping with renal failure.

Ultra high frequency follow-on communications satellite system

NASA Astrophysics Data System (ADS)

Hassien, Michael J.

1992-03-01

The existing constellation of UHF communications satellites (LEASAT and FLTSAT) provide key command and control links for mobile forces of the DoD and other government agencies. The UHF Follow-On satellite program will provide for a new generation of communications satellites to replace the existing ones as they reach the end of their life cycle beginning in 1992. Continued coverage is required for both peacetime and crisis environments, and must be maintained indefinitely. An eight-satellite UFO constellation (two per coverage area) will replenish the existing FLTSATCOM constellation.

78 FR 21924 - Alabama Power Company; Notice of Application for Amendment of License and Soliciting Comments...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-12

... approval to replace the Unit 4 turbine at the Jordan Dam Project. Specifically, the licensee proposes the following work: complete turbine replacement, wicket gate system rehabilitation or replacement, gate stem bushing replacement, turbine and generator bearing refurbishment, and related component replacement. The...

The future of mechanical circulatory support for advanced heart failure.

PubMed

Marinescu, Karolina K; Uriel, Nir; Adatya, Sirtaz

2016-05-01

Mechanical circulatory support (MCS) has become the main focus of heart replacement therapy for end stage heart failure patients. Advances in technology are moving towards miniaturization, biventricular support devices, complete internalization, improved hemocompatibility profiles, and responsiveness to cardiac loading conditions. This review will discuss the recent advances and investigational devices in MCS for advanced heart failure. The demand for both short-term and long-term durable devices for advanced heart failure is increasing. The current devices are still fraught with an unacceptably high incidence of gastrointestinal bleeding and thromboembolic and infectious complications. New devices are on the horizon focusing on miniaturization, versatility for biventricular support, improved hemocompatibility, use of alternate energy sources, and incorporation of continuous hemodynamic monitoring. The role for MCS in advanced heart replacement therapy is steadily increasing. With the advent of newer generation devices on the horizon, the potential exists for MCS to surpass heart transplantation as the primary therapy for advanced heart failure.

Motor power factor controller with a reduced voltage starter

NASA Technical Reports Server (NTRS)

Nola, F. J. (Inventor)

1981-01-01

A power factor type motor controller is disclosed in which the conventional power factor constant voltage command signal is replaced during a starting interval with a graduated control voltage. This continuation-impart of a pending patent application (Serial No. 199, 765: Three Phase Factor Controller) provides a means for modifying the operation of the system for a motor start-up interval of 5 to 30 second. Using a ramp generators, an initial ramp-like signal replaces a constant power factor signal supplied by a potentiometer. The ramp-like signal is applied to a 15 terminal where it is summed with an operating power factor signal from phase detectors in order to obtain a control signal for ultimately controlling SCR devices. The SCR devices are turned on at an advancing rate with time responsive to the combination signal described rather than simply a function of a ramp-like signal alone.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, K.J.; Wales, D.

This document presents a gasket replacement study performed by AAI Corporation for the U.S. Army Chemical Research, Development and Engineering Center. The new gaskets will replace those currently used in the M3A3 Smoke Generator. In accordance with Delivery Order 0002, AAI performed the following tasks: (1) Conducted a literature and industry search for new gasket material, (2) Selected and procured four of the most promising replacement materials, (3) Tested gaskets fabricated from these materials using a GFE M3A3 Smoke Generator, and (4) Recommended final replacement gaskets based on cost, chemical and temperature resistance, and test performance.

Optimizing Culture Medium Composition to Improve Oligodendrocyte Progenitor Cell Yields In Vitro from Subventricular Zone-Derived Neural Progenitor Cell Neurospheres

PubMed Central

Franco, Paula G.; Pasquini, Juana M.; Silvestroff, Lucas

2015-01-01

Neural Stem and Progenitor Cells (NSC/NPC) are gathering tangible recognition for their uses in cell therapy and cell replacement therapies for human disease, as well as a model system to continue research on overall neural developmental processes in vitro. The Subventricular Zone is one of the largest NSC/NPC niches in the developing mammalian Central Nervous System, and persists through to adulthood. Oligodendrocyte progenitor cell (OPC) enriched cultures are usefull tools for in vitro studies as well as for cell replacement therapies for treating demyelination diseases. We used Subventricular Zone-derived NSC/NPC primary cultures from newborn mice and compared the effects of different growth factor combinations on cell proliferation and OPC yield. The Platelet Derived Growth Factor-AA and BB homodimers had a positive and significant impact on OPC generation. Furthermore, heparin addition to the culture media contributed to further increase overall culture yields. The OPC generated by this protocol were able to mature into Myelin Basic Protein-expressing cells and to interact with neurons in an in vitro co-culture system. As a whole, we describe an optimized in vitro method for increasing OPC. PMID:25837625

Cells adapted to the proteasome inhibitor 4-hydroxy- 5-iodo-3-nitrophenylacetyl-Leu-Leu-leucinal-vinyl sulfone require enzymatically active proteasomes for continued survival

PubMed Central

Princiotta, Michael F.; Schubert, Ulrich; Chen, Weisan; Bennink, Jack R.; Myung, Jayhyuk; Crews, Craig M.; Yewdell, Jonathan W.

2001-01-01

The proteasome is the primary protease used by cells for degrading proteins and generating peptide ligands for class I molecules of the major histocompatibility complex. Based on the properties of cells adapted to grow in the presence of the proteasome inhibitor 4-hydroxy-5-iodo-3-nitrophenylacetyl-Leu-Leu-leucinal-vinyl sulfone (NLVS), it was proposed that proteasomes can be replaced by alternative proteolytic systems, particularly a large proteolytic complex with a tripeptidyl peptidase II activity. Here we show that NLVS-adapted cells retain sensitivity to a number of highly specific proteasome inhibitors with regard to antigenic peptide generation, accumulation of polyubiquitinated proteins, degradation of p53, and cell viability. In addition, we show that in the same assays (with a single minor exception), NLVS-adapted cells are about as sensitive as nonselected cells to Ala-Ala-Phe-chloromethylketone, a specific inhibitor of tripeptidyl peptidase II activity. Based on these findings, we conclude that proteasomes still have essential proteolytic functions in adapted cells that are not replaced by Ala-Ala-Phe-chloromethylketone-sensitive proteases. PMID:11149939

Continuous vasopressin replacement in diabetes insipidus.

PubMed Central

Ralston, C; Butt, W

1990-01-01

Five children who developed diabetes insipidus as a manifestation of severe brain injury received continuous intravenous treatment with a solution containing both aqueous vasopressin and appropriate crystalloid replacement. Polyuria, hypernatraemia, and decreased urine osmolalities were safely corrected in all patients within eight to 28 hours. PMID:2400231

Blood loss associated with Ring uncemented total knee replacement: comparison between continuous and intermittent suction drainage.

PubMed Central

Wittmann, F W; Ring, P A

1984-01-01

In a retrospective comparison of blood loss following uncemented total knee replacement, in which either continuous or intermittent suction drainage was used, measured blood loss was significantly greater with continuous drainage. However, a method of calculating actual blood loss demonstrated no significant difference. With intermittent drainage, more blood remains undetected around the knee joint; this technique should therefore be abandoned in favour of continuous suction drainage. PMID:6747978

COMPUTER AIDED DESIGN OF REPLACEMENT SOLVENTS UNDER VARYING ENVIRONMENTAL CONSTRAINTS

EPA Science Inventory

There is a great need to replace many solvents that are commonly used by industry and the public, but whose continued use entails a number of human health and environmental risks. One problem hampering solvent replacement is the thought that replacement, particularly for environm...

21 CFR 870.3710 - Pacemaker repair or replacement material.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Pacemaker repair or replacement material. 870.3710... (CONTINUED) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3710 Pacemaker repair or replacement material. (a) Identification. A pacemaker repair or replacement material is an...

21 CFR 870.3710 - Pacemaker repair or replacement material.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Pacemaker repair or replacement material. 870.3710... (CONTINUED) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3710 Pacemaker repair or replacement material. (a) Identification. A pacemaker repair or replacement material is an...

21 CFR 870.3710 - Pacemaker repair or replacement material.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Pacemaker repair or replacement material. 870.3710... (CONTINUED) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3710 Pacemaker repair or replacement material. (a) Identification. A pacemaker repair or replacement material is an...

21 CFR 870.3710 - Pacemaker repair or replacement material.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Pacemaker repair or replacement material. 870.3710... (CONTINUED) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3710 Pacemaker repair or replacement material. (a) Identification. A pacemaker repair or replacement material is an...

Energy Efficiency Upgrades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roby Williams

2012-03-29

The energy efficiency upgrades project at Hardin County General Hospital did not include research nor was it a demonstration project. The project enabled the hospital to replace outdated systems with modern efficient models. Hardin County General Hospital is a 501c3, nonprofit hospital and the sole community provider for Hardin and Pope Counties of Illinois. This project provided much needed equipment and facility upgrades that would not have been possible through locally generated funding. Task 1 was a reroofing of the hospital. The hospital architect designed the replacement to increase the energy efficiency of the hospital roof/ceiling structure. Task 2 wasmore » replacement and installation of a new more efficient CT scanner for the hospital. Included in the project was replacement of HVAC equipment for the entire radiological suite. Task 5 was a replacement and installation of a new higher capacity diesel-fueled emergency generator for the hospital replacing a 50+ year old gas-fired generator. Task 7 was the replacement of 50+ year-old walk-in cooler/freezer with a newer, energy efficient model. Task 8 was the replacement of 10+ year-old washing machines in the hospital laundry with higher capacity, energy efficient models. Task 9 was replacement of 50-year old single pane curtain window system with double-pane insulated windows. Additionally, insulation was added around ventilation systems and the curtain wall system.« less

Faster Blood Flow Rate Does Not Improve Circuit Life in Continuous Renal Replacement Therapy: A Randomized Controlled Trial.

PubMed

Fealy, Nigel; Aitken, Leanne; du Toit, Eugene; Lo, Serigne; Baldwin, Ian

2017-10-01

To determine whether blood flow rate influences circuit life in continuous renal replacement therapy. Prospective randomized controlled trial. Single center tertiary level ICU. Critically ill adults requiring continuous renal replacement therapy. Patients were randomized to receive one of two blood flow rates: 150 or 250 mL/min. The primary outcome was circuit life measured in hours. Circuit and patient data were collected until each circuit clotted or was ceased electively for nonclotting reasons. Data for clotted circuits are presented as median (interquartile range) and compared using the Mann-Whitney U test. Survival probability for clotted circuits was compared using log-rank test. Circuit clotting data were analyzed for repeated events using hazards ratio. One hundred patients were randomized with 96 completing the study (150 mL/min, n = 49; 250 mL/min, n = 47) using 462 circuits (245 run at 150 mL/min and 217 run at 250 mL/min). Median circuit life for first circuit (clotted) was similar for both groups (150 mL/min: 9.1 hr [5.5-26 hr] vs 10 hr [4.2-17 hr]; p = 0.37). Continuous renal replacement therapy using blood flow rate set at 250 mL/min was not more likely to cause clotting compared with 150 mL/min (hazards ratio, 1.00 [0.60-1.69]; p = 0.68). Gender, body mass index, weight, vascular access type, length, site, and mode of continuous renal replacement therapy or international normalized ratio had no effect on clotting risk. Continuous renal replacement therapy without anticoagulation was more likely to cause clotting compared with use of heparin strategies (hazards ratio, 1.62; p = 0.003). Longer activated partial thromboplastin time (hazards ratio, 0.98; p = 0.002) and decreased platelet count (hazards ratio, 1.19; p = 0.03) were associated with a reduced likelihood of circuit clotting. There was no difference in circuit life whether using blood flow rates of 250 or 150 mL/min during continuous renal replacement therapy.

40 CFR 141.84 - Lead service line replacement requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Lead service line replacement requirements. 141.84 Section 141.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.84 Lead...

40 CFR 141.84 - Lead service line replacement requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Lead service line replacement requirements. 141.84 Section 141.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.84 Lead...

Third-generation pure alumina and alumina matrix composites in total hip arthroplasty

PubMed Central

Hannouche, Didier; Zingg, Matthieu; Miozzari, Hermes; Nizard, Remy; Lübbeke, Anne

2018-01-01

Wear, corrosion and periprosthetic osteolysis are important causes of failure in joint arthroplasty, especially in young patients. Ceramic bearings, developed 40 years ago, are an increasingly popular choice in hip arthroplasty. New manufacturing procedures have increased the strength and reliability of ceramic materials and reduced the risk of complications. In recent decades, ceramics made of pure alumina have continuously improved, resulting in a surgical-grade material that fulfills clinical requirements. Despite the track record of safety and long-term results, third-generation pure alumina ceramics are being replaced in clinical practice by alumina matrix composites, which are composed of alumina and zirconium. In this review, the characteristics of both materials are discussed, and the long-term results with third-generation alumina-on-alumina bearings and the associated complications are compared with those of other available ceramics. Cite this article: EFORT Open Rev 2018;3:7-14. DOI: 10.1302/2058-5241.3.170034 PMID:29657840

7 CFR 274.6 - Replacement issuances and cards to households.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 4 2014-01-01 2014-01-01 false Replacement issuances and cards to households. 274.6 Section 274.6 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION... Excessive Replacement Card Notice if they have chosen to exercise the option to withhold the replacement...

A case of rhabdomyolysis after kidney transplantation successfully managed with intensive continuous dialysis.

PubMed

Shahbazov, Rauf; Fox, Michael; Alejo, Jennifer L; Anjum, Malik A; Azari, Feredun; Doyle, Alden; Agarwal, Avinash; Brayman, Kenneth L

2018-04-01

Rhabdomyolysis is characterized by muscle cell death which can result in acute kidney injury from pigment nephropathy. We present a patient who developed rhabdomyolysis immediately after deceased donor kidney transplantation surgery and was managed with continuous renal replacement therapy that resulted in successful salvage of the kidney allograft. Patients who develop acute kidney failure requiring renal replacement therapy generally have a poor prognosis. It is worth noting that while continuous veno-venous hemofiltration (CVVHF) offers greater volume support and continuous clearance compared to hemodialysis (HD), recent studies have demonstrated no clinically significant improvement in clinical outcome between the two. Perhaps CVVHF is a better modality compared to HD in this setting to prevent further insult from pigment nephropathy to an allograft. A combination of early diagnosis and intensive continuous renal replacement therapy can be used for allograft salvage in a patient with rhabdomyolysis in the immediate post-kidney transplant period.

Pacemaker

MedlinePlus

... check for changes in your heart's electrical activity. Battery Replacement Pacemaker batteries last between 5 and 15 years (average 6 ... doctor will replace the generator along with the battery before the battery starts to run down. Replacing ...

New Generation General Purpose Computer (GPC) compact IBM unit

NASA Technical Reports Server (NTRS)

1991-01-01

New Generation General Purpose Computer (GPC) compact IBM unit replaces a two-unit earlier generation computer. The new IBM unit is documented in table top views alone (S91-26867, S91-26868), with the onboard equipment it supports including the flight deck CRT screen and keypad (S91-26866), and next to the two earlier versions it replaces (S91-26869).

46 CFR 59.01-5 - Repairs, replacements, or alterations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Repairs, replacements, or alterations. 59.01-5 Section 59.01-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING REPAIRS TO BOILERS, PRESSURE VESSELS AND APPURTENANCES General Requirements § 59.01-5 Repairs, replacements, or alterations. (a) No repairs, replacements, or...

46 CFR 59.01-5 - Repairs, replacements, or alterations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Repairs, replacements, or alterations. 59.01-5 Section 59.01-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING REPAIRS TO BOILERS, PRESSURE VESSELS AND APPURTENANCES General Requirements § 59.01-5 Repairs, replacements, or alterations. (a) No repairs, replacements, or...

46 CFR 59.01-5 - Repairs, replacements, or alterations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Repairs, replacements, or alterations. 59.01-5 Section 59.01-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING REPAIRS TO BOILERS, PRESSURE VESSELS AND APPURTENANCES General Requirements § 59.01-5 Repairs, replacements, or alterations. (a) No repairs, replacements, or...

46 CFR 59.01-5 - Repairs, replacements, or alterations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Repairs, replacements, or alterations. 59.01-5 Section 59.01-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING REPAIRS TO BOILERS, PRESSURE VESSELS AND APPURTENANCES General Requirements § 59.01-5 Repairs, replacements, or alterations. (a) No repairs, replacements, or...

46 CFR 59.01-5 - Repairs, replacements, or alterations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Repairs, replacements, or alterations. 59.01-5 Section 59.01-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING REPAIRS TO BOILERS, PRESSURE VESSELS AND APPURTENANCES General Requirements § 59.01-5 Repairs, replacements, or alterations. (a) No repairs, replacements, or...

Impact of computerized order entry and pre-mixed dialysis solutions for continuous veno-venous hemodiafiltration on selection of therapy for acute renal failure.

PubMed

Saadulla, Lawand; Reeves, W Brian; Irey, Brittany; Ghahramani, Nasrollah

2012-02-01

To investigate the impacts of availability of pre-mixed solutions and computerized order entry on nephrologists' choice of the initial mode of renal replacement therapy in acute renal failure. We studied 898 patients with acute renal failure in 3 consecutive eras: era 1 (custom-mixed solution; n = 309), era 2 (pre-mixed commercial solution; n = 324), and era 3 (post-computerized order entry; n = 265). The proportion of patients treated with renal replacement therapy and the time from consult to initiation of continuous renal replacement therapy was similar in the 3 eras. Following introduction of the pre-mixed solution, the proportion of patients treated with continuous renal replacement therapy increased (20% vs. 33%; p < 0.05), it was initiated at a lower serum creatinine (353 ± 123 μmol/L vs. 300 ± 80 μmol/L; p < 0.05) and in older patients (53 ± 12 vs. 61 ± 14 years; p < 0.05). There was a progressive increase in the use of continuous veno-venous hemodialysis (18% vs. 79% vs. 100%; p < 0.05) and in the total prescribed flow rate (1,382 ± 546 vs. 2,324 ± 737 vs. 2,900 ± 305 mL/hr 3; p < 0.05). There was no significant impact on mortality. The availability of a pre-mixed solution increases the likelihood of initiating continuous renal replacement therapy in acute renal failure, initiating it at a lower creatinine and for older patients, use of continuous veno-venous hemodialysis and higher prescribed continuous renal replacement therapy dose. Computerized order entry implementation is associated with an additional increase in the use of continuous veno-venous hemodialysis, higher total prescribed dialysis dose, and use of CRRT among an increasing number of patients not on mechanical ventilation. The effect of these changes on patient survival is not significant.

Extreme ultraviolet resist materials for sub-7 nm patterning.

PubMed

Li, Li; Liu, Xuan; Pal, Shyam; Wang, Shulan; Ober, Christopher K; Giannelis, Emmanuel P

2017-08-14

Continuous ongoing development of dense integrated circuits requires significant advancements in nanoscale patterning technology. As a key process in semiconductor high volume manufacturing (HVM), high resolution lithography is crucial in keeping with Moore's law. Currently, lithography technology for the sub-7 nm node and beyond has been actively investigated approaching atomic level patterning. EUV technology is now considered to be a potential alternative to HVM for replacing in some cases ArF immersion technology combined with multi-patterning. Development of innovative resist materials will be required to improve advanced fabrication strategies. In this article, advancements in novel resist materials are reviewed to identify design criteria for establishment of a next generation resist platform. Development strategies and the challenges in next generation resist materials are summarized and discussed.

Estimating the Risks and Benefits of Implantable Cardioverter Defibrillator Generator Replacement: A Systematic Review.

PubMed

Lewis, Krystina B; Stacey, Dawn; Carroll, Sandra L; Boland, Laura; Sikora, Lindsey; Birnie, David

2016-07-01

Every 4-7 years an implantable cardioverter defibrillator (ICD) pulse generator must be replaced surgically. This procedure is not without risk. In some cases, the risk versus benefit ratio may be against replacement. We aimed to synthesize the evidence on risks, benefits, and costs related to ICD replacement. A systematic review was conducted using electronic databases from 2000 onward. Literature screening, quality appraisal, and data extraction were independently conducted by two reviewers. Outcomes included major and minor complications, ICD therapies, and costs, which were synthesized descriptively. Of 1,483 citations, 17 nonrandomized studies met criteria. Median rate of major complications was 4.05% (range 0.55-7.37%) and minor complications was 3.50% (range 0.36-7.37%). Without non-ICD control groups, the true risk reduction provided by the ICD following replacement is unknown. Following ICD replacement, annualized rate of appropriate ICD therapy was 10.52% (range 2.42-75.00%). Of these, patients without therapies during their first generator life and those no longer meeting ICD criteria received appropriate therapies at nontrivial rates. Rates of complications associated with ICD replacement are substantial. No study had nonreplacement groups, hence the true risk reduction provided by the ICD following replacement is unknown. Our analysis did not identify a subgroup at low risk of therapies following replacement. Shared discussions should occur with patients about the evidence, healthcare goals, risk tolerances, and feelings about life and death trade-offs to enable high-quality decisions about ICD replacement. ©2016 Wiley Periodicals, Inc.

Review: New Vaccine Against Tuberculosis: Current Developments and Future Challenges

NASA Astrophysics Data System (ADS)

Liu, Jun

2009-04-01

Tuberculosis (TB) continues to be a global health threat. BCG was developed as an attenuated live vaccine for tuberculosis control nearly a century ago. Despite being the most widely used vaccine in human history, BCG is not an ideal vaccine and has two major limitations: its poor efficacy against adult pulmonary TB and its disconcerting safety in immunocompromised individuals. A safer and more effective TB vaccine is urgently needed. This review article discusses current strategies to develop the next generation of TB vaccines to replace BCG. While some progresses have been made in the past decade, significant challenges lie ahead.

Experimental Investigation of Free-Convection Heat Transfer in Vertical Tube at Large Grashof Numbers

NASA Technical Reports Server (NTRS)

Eckert, E R G; Diaguila, A J

1955-01-01

Report presents the results of an investigation conducted to study free-convection heat transfer in a stationary vertical tube closed at the bottom. The walls of the tube were heated, and heated air in the tube was continuously replaced by fresh cool air at the top. The tube was designed to provide a gravitational field with Grashof numbers of a magnitude comparable with those generated by the centrifugal field in rotating-blade coolant passages (10(8) to 10(13)). Local heat-transfer coefficients in the turbulent-flow range and the temperature field within the fluid were obtained.

B-Raf kinase inhibitors: hit enrichment through scaffold hopping.

PubMed

Gopalsamy, Ariamala; Shi, Mengxiao; Hu, Yongbo; Lee, Frederick; Feldberg, Larry; Frommer, Eileen; Kim, Steven; Collins, Karen; Wojciechowicz, Donald; Mallon, Robert

2010-04-15

In continuation of our efforts toward hit identification and optimization for a B-Raf kinase project, we have employed a scaffold hopping strategy. The original HTS hit scaffold pyrazolo[1,5-a]pyrimidine was replaced with different thienopyrimidine and thienopyridine scaffolds to append the optimal pharmacophore moieties in order to generate novel B-raf kinase inhibitors with desirable potency and properties. This strategy led to the identification of additional lead compound 11b which had good enzyme and cell potency, while maintaining selectivity over a number of kinases. Copyright 2010 Elsevier Ltd. All rights reserved.

A Novel Way Of Repair Of Insulation Breaks During Pacemaker Generator Replacement

PubMed Central

Manzoor Ali, Syed; Iqbal, Khurshid; Tramboo, Nisar A; Lone, Aijaz A; Kaul, Suresh; Kaul, Neelam; Hafiz, Imran

2009-01-01

Minor abrasions can occur while mobilising old lead during pacemaker generator replacement necesittating placement of additional lead adding to the financial burden and junk in heart. We describe a novel way of repair of old pacemaker lead preventing additional lead placement. PMID:19763196

Changing spatial patterns of stand-replacing fire in California conifer forests

Treesearch

Jens T. Stevens; Brandon M. Collins; Jay D. Miller; Malcolm P. North; Scott L. Stephens

2017-01-01

Stand-replacing fire has profound ecological impacts in conifer forests, yet there is continued uncertainty over how best to describe the scale of stand-replacing effects within individual fires, and how these effects are changing over time. In forests where regeneration following stand-replacing fire depends on seed dispersal from surviving trees, the size and shape...

Proton Exchange Membrane Fuel Cell Engineering Model Powerplant. Test Report: Benchmark Tests in Three Spatial Orientations

NASA Technical Reports Server (NTRS)

Loyselle, Patricia; Prokopius, Kevin

2011-01-01

Proton exchange membrane (PEM) fuel cell technology is the leading candidate to replace the aging alkaline fuel cell technology, currently used on the Shuttle, for future space missions. This test effort marks the final phase of a 5-yr development program that began under the Second Generation Reusable Launch Vehicle (RLV) Program, transitioned into the Next Generation Launch Technologies (NGLT) Program, and continued under Constellation Systems in the Exploration Technology Development Program. Initially, the engineering model (EM) powerplant was evaluated with respect to its performance as compared to acceptance tests carried out at the manufacturer. This was to determine the sensitivity of the powerplant performance to changes in test environment. In addition, a series of tests were performed with the powerplant in the original standard orientation. This report details the continuing EM benchmark test results in three spatial orientations as well as extended duration testing in the mission profile test. The results from these tests verify the applicability of PEM fuel cells for future NASA missions. The specifics of these different tests are described in the following sections.

SOLVENT DESIGN UNDER VARYING ENVIRONMENTAL REQUIREMENTS

EPA Science Inventory

There is currently a great need to replace many solvents that are commonly used by industry and the public, but whose continued use entails a number of human health and environmental risks. One issue hampering solvent replacement is the general thought that replacement, particul...

77 FR 41814 - Entergy Operations, Inc.; Grand Gulf Nuclear Station, Unit 1

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-16

... Unit 1 result primarily from periodic testing of diesel generators and fire water pump diesel engines... rural. GGNS Unit 1 is a General Electric Mark 3 boiling-water reactor. Identification of the Proposed... following: replacing the reactor feed pump turbine rotors; replacing the main generator current transformers...

The Salary Premium Required for Replacing Management Faculty: Evidence from a National Survey

ERIC Educational Resources Information Center

Finch, J. Howard; Allen, Richard S.; Weeks, H. Shelton

2010-01-01

One of the most important aspects of growing and improving business education is replacing departed faculty members. As the baby-boom generation approaches retirement, the supply of available replacement faculty members is diminishing. The result is a competitive market for replacement faculty that features increasing starting salary levels. In…

Recombinant FVIIa (NovoSeven) continuous infusion and total hip replacement in patients with haemophilia and high titre of inhibitors to FVIII: experience of two cases.

PubMed

Tagariello, G; De Biasi, E; Gajo, G B; Risato, R; Radossi, P; Davoli, P G; Traldi, A

2000-09-01

In this report we describe our experience of total hip replacement in two patients with severe haemophilia A and high titres of inhibitors to FVIII. We used rFVIIa replacement therapy by continuous infusion to perform the surgery. The total amount of rFVIIa used in these two patients was very similar but the manner of administration was quite different. In our experience, it is an advantage to use a higher dose for shorter periods than a lower dose for a longer treatment period. Tranexamic acid by continuous infusion, and parallel saline infusion were useful for good haemostasis and avoided local thrombophlebitis in the side of rFVIIa infusion.

[Critical care nurse learning of continuous renal replacement therapy: the efficacy of a self-learning manual].

PubMed

Huang, Yi-Chen; Hsu, Li-Ling

2011-02-01

Many nurses have difficulty learning to use the complex, non-traditional, and regularly-updated critical care equipment. Failure to use such equipment properly can seriously compromise treatment and endanger patient health and lives. New self-learning materials for novice nurses are necessary to provide essential and effective guidance as a part of formal nursing training. Such materials can enhance the capabilities of critical care nurses and, thus, improve the general quality of critical care. The purpose of this research was to develop a continuous renal replacement therapy (CRRT)-themed self-learning manual that would provide easily absorbed and understood knowledge in an easy-to-carry format for ICU nursing staff. This study also investigated CCRT skill learning efficacy. This study adopted a quasi-experimental design with pretests and posttests. Purposive sampling generated a sample of 66 critical care nurses currently working at one hospital in Taipei City. Participants submitted a completed self-assessment survey that rated their command of continuous renal replacement therapy before and after the self-learning manual intervention. Survey data were analyzed using SPSS Version 17.0 for Windows. The two major findings derived from the study included: (1) The mean response score from the self-assessment survey filled out after the intervention was 91.06 and 79.75 (SD = 9.49 and 11.65), respectively, for experimental and control groups. Such demonstrated significant difference. (2) The mean posttest score after the intervention for the experimental group was 91.06 ± 9.49. This represents a significant increase of 10.35 ± 10.35 over their mean pretest score (80.71 ± 11.82). The experimental group showed other significant differences in terms of the CRRT self-assessment survey posttest. Self-learning manuals may be introduced in nursing education as useful aids and catalysts to achieve more effective and satisfying learning experiences.

The economic impact of battery longevity in implantable cardioverter-defibrillators for cardiac resynchronization therapy: the hospital and healthcare system perspectives.

PubMed

Landolina, Maurizio; Morani, Giovanni; Curnis, Antonio; Vado, Antonello; D'Onofrio, Antonio; Bianchi, Valter; Stabile, Giuseppe; Crosato, Martino; Petracci, Barbara; Ceriotti, Carlo; Bontempi, Luca; Morosato, Martina; Ballari, Gian Paolo; Gasparini, Maurizio

2017-08-01

Patients receiving cardiac resynchronization therapy defibrillators (CRT-Ds) are likely to undergo one or more device replacements, mainly for battery depletion. We assessed the economic impact of battery depletion on the overall cost of CRT-D treatment from the perspectives of the healthcare system and the hospital. We also compared devices of different generations and from different manufacturers in terms of therapy cost. We analysed data on 1792 CRT-Ds implanted in 1399 patients in 9 Italian centres. We calculated the replacement probability and the total therapy cost over 6 years, stratified by device generation and manufacturer. Public tariffs from diagnosis-related groups were used together with device prices and hospitalization costs. Generators were from 3 manufacturers: Boston Scientific (667, 37%), Medtronic (973, 54%), and St Jude Medical (152, 9%). The replacement probability at 6 years was 83 and 68% for earlier- and recent-generation devices, respectively. The need for replacement increased total therapy costs by more than 50% over the initial implantation cost for hospitals and by more than 30% for healthcare system. The improved longevity of recent-generation CRT-Ds reduced the therapy cost by ∼6% in both perspectives. Among recent-generation CRT-Ds, the replacement probability of devices from different manufacturers ranged from 12 to 70%. Consequently, the maximum difference in therapy cost between manufacturers was 40% for hospitals and 19% for the healthcare system. Differences in CRT-D longevity strongly affect the overall therapy cost. While the use of recent-generation devices has reduced the cost, significant differences exist among currently available systems. © The Author 2016. Published by Oxford University Press on behalf of the European Society of Cardiology.

38 CFR 21.220 - Replacement of supplies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) VOCATIONAL REHABILITATION AND EDUCATION Vocational Rehabilitation and Employment Under 38 U.S.C... will replace articles which are necessary to further pursuit of the veteran's program and which are... advancement from the Vocational Rehabilitation Revolving Fund to a veteran to replace articles for which VA...

42 CFR 419.66 - Transitional pass-through payments: Medical devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... replace human skin (for example, a biological skin replacement material or synthetic skin replacement... HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM PROSPECTIVE PAYMENT SYSTEM FOR HOSPITAL OUTPATIENT... human tissue, and is surgically implanted or inserted whether or not it remains with the patient when...

42 CFR 419.66 - Transitional pass-through payments: Medical devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... replace human skin (for example, a biological skin replacement material or synthetic skin replacement... HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM PROSPECTIVE PAYMENT SYSTEM FOR HOSPITAL OUTPATIENT... human tissue, and is surgically implanted or inserted whether or not it remains with the patient when...

40 CFR 1068.240 - What are the provisions for exempting new replacement engines?

Code of Federal Regulations, 2010 CFR

2010-07-01

... new replacement engines? 1068.240 Section 1068.240 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Exemptions and Exclusions § 1068.240 What are the provisions for exempting new replacement engines? The...

The management of heat stress for the firefighter: a review of work conducted on behalf of the Toronto Fire Service.

PubMed

McLellan, Tom M; Selkirk, Glen A

2006-07-01

This report provides a summary of research conducted through a grant provided by the Workplace Safety Insurance Board of Ontario. The research was divided into two phases; first, to define safe work limits for firefighters wearing their protective clothing and working in warm environments; and, the second, to examine strategies to reduce the thermal burden and extend the operational effectiveness of the firefighter. For the first phase, subjects wore their protective ensemble and carried their self-contained breathing apparatus (SCBA) and performed very light, light, moderate or heavy work at 25 degrees C, 30 degrees C or 35 degrees C. Thermal and evaporative resistance coefficients were obtained from thermal manikin testing that allowed the human physiological responses to be compared with modeled data. Predicted continuous work times were then generated using a heat strain model that established limits for increases in body temperature to 38.0 degrees C, 38.5 degrees C and 39.0 degrees C. Three experiments were conducted for the second phase of the project. The first study revealed that replacing the duty uniform pants that are worn under the bunker pants with shorts reduced the thermal strain for activities that lasted longer than 60 min. The second study examined the importance of fluid replacement. The data revealed that fluid replacement equivalent to at least 65% of the sweat lost increased exposure time by 15% compared with no fluid replacement. The last experiment compared active and passive cooling. Both the use of a mister or forearm and hand submersion in cool water significantly increased exposure time compared with passive cooling that involved only removing most of the protective clothing. Forearm and hand submersion proved to be most effective and produced dramatic increases in exposure time that approximated 65% compared with the passive cooling procedure. When the condition of no fluid replacement and passive cooling was compared with fluid replacement and forearm and hand submersion, exposure times were effectively doubled with the latter condition. The heat stress wheel that was generated can be used by Commanders to determine safe work limits for their firefighters during activities that involve wearing their protective clothing and carrying their SCBA.

Development of Advanced High Strength Cast Alloys for Heavy Duty Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barlow, James

Gray iron has been the primary alloy for heavy duty diesel engine core castings for decades. During recent decades the limitations of gray iron have been reached in some applications, leading to the use of compacted graphite iron in engine blocks and heads. Caterpillar has had compacted graphite designs in continuous production since the late 1980’s. Due to the drive for higher power density, decreased emissions and increased fuel economy, cylinder pressures and temperatures continue to increase. Currently no viable replacement for today’s compacted graphite irons exist at an acceptable cost level. This project explored methods to develop the nextmore » generation of heavy duty diesel engine materials as well as demonstrated some results on new alloy designs although cost targets will likely not be met.« less

Photovoltaic prospects in Europe

NASA Astrophysics Data System (ADS)

Starr, M. R.

The economics of solar cells is reviewed with an eye to potential cost reductions in processing, and potential markets are explored. Current solar cell systems costs are noted to be on the road to achieving the U.S. DoE goals of $0.40/kWp by 1990. Continued progress will depend on technical developments in cheaper materials and processes, scaling up production, and the success of sales programs. Various consumer and professional markets are outlined, with a prediction that a 12 MWp deman will be reached as a steady state by 1995. Photovoltaic panels may conceivably replace conventional roofing materials, resulting in the projection that, if grid-supplied power continues to inflate in price, then all new European homes would be equipped with photovoltaics by the year 2000. Further, accomplishment of the cost goals could generate a 1 GWp/yr industrial market at the same time.

Responses of leaf traits to climatic gradients: adaptive variation versus compositional shifts

NASA Astrophysics Data System (ADS)

Meng, T.-T.; Wang, H.; Harrison, S. P.; Prentice, I. C.; Ni, J.; Wang, G.

2015-09-01

Dynamic global vegetation models (DGVMs) typically rely on plant functional types (PFTs), which are assigned distinct environmental tolerances and replace one another progressively along environmental gradients. Fixed values of traits are assigned to each PFT; modelled trait variation along gradients is thus driven by PFT replacement. But empirical studies have revealed "universal" scaling relationships (quantitative trait variations with climate that are similar within and between species, PFTs and communities); and continuous, adaptive trait variation has been proposed to replace PFTs as the basis for next-generation DGVMs. Here we analyse quantitative leaf-trait variation on long temperature and moisture gradients in China with a view to understanding the relative importance of PFT replacement vs. continuous adaptive variation within PFTs. Leaf area (LA), specific leaf area (SLA), leaf dry matter content (LDMC) and nitrogen content of dry matter were measured on all species at 80 sites ranging from temperate to tropical climates and from dense forests to deserts. Chlorophyll fluorescence traits and carbon, phosphorus and potassium contents were measured at 47 sites. Generalized linear models were used to relate log-transformed trait values to growing-season temperature and moisture indices, with or without PFT identity as a predictor, and to test for differences in trait responses among PFTs. Continuous trait variation was found to be ubiquitous. Responses to moisture availability were generally similar within and between PFTs, but biophysical traits (LA, SLA and LDMC) of forbs and grasses responded differently from woody plants. SLA and LDMC responses to temperature were dominated by the prevalence of evergreen PFTs with thick, dense leaves at the warm end of the gradient. Nutrient (N, P and K) responses to climate gradients were generally similar within all PFTs. Area-based nutrients generally declined with moisture; Narea and Karea declined with temperature, but Parea increased with temperature. Although the adaptive nature of many of these trait-climate relationships is understood qualitatively, a key challenge for modelling is to predict them quantitatively. Models must take into account that community-level responses to climatic gradients can be influenced by shifts in PFT composition, such as the replacement of deciduous by evergreen trees, which may run either parallel or counter to trait variation within PFTs. The importance of PFT shifts varies among traits, being important for biophysical traits but less so for physiological and chemical traits. Finally, models should take account of the diversity of trait values that is found in all sites and PFTs, representing the "pool" of variation that is locally available for the natural adaptation of ecosystem function to environmental change.

Surplus from and storage of electricity generated by intermittent sources

NASA Astrophysics Data System (ADS)

Wagner, Friedrich

2016-12-01

Data from the German electricity system for the years 2010, 2012, 2013, and 2015 are used and scaled up to a 100% supply by intermittent renewable energy sources (iRES). In the average, 330GW wind and PV power are required to meet this 100% target. A back-up system is necessary with the power of 89% of peak load. Surplus electricity accrues at high power levels. Curtailing surplus power to a large extent is found to be uneconomic. Demand-side management will suffer from the strong day-to-day variation of available surplus energy. A day storage is ineffective because of the day-night correlation of surplus power during winter. A seasonal storage loses its character when transformation losses are considered because it can contribute only after periods with excessive surplus production. The option of an oversized iRES system to feed the storage is also not effective because, in this case, energy can be taken directly from the large iRES supply, making storage superfluous. The capacities to be installed stress the difficulty to base heat supply and mobility also on iRES generated electricity in the future. As the German energy transition replaces one CO2-free electricity supply system by another one, no major reduction in CO2 emission can be expected till 2022, when the last nuclear reactor will be switched off. By 2022, an extremely oversized power supply system has to be created, which can be expected to continue running down spot-market electricity prices. The continuation of the economic response -to replace expensive gas fuel by cheap lignite- causes an overall increase in CO2 emission. The German GHG emission targets for 2020 and beyond are therefore in jeopardy.

77 FR 71483 - Airworthiness Directives; Turbomeca S.A. Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-03

... collected during cleaning exceeds 8 grams. This AD also includes an optional terminating action. This AD was... replacing the rear bearing if the amount of dust collected during cleaning exceeds 8 grams. That NPRM also... gas generator hollow shaft is more than 8 grams, replace the gas generator rear bearing before further...

Current Status of Continued Operation for Kori unit 1 beyond Design Life

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tai-hyun Kim; Pan-sool Kim; Yeon-sang Yu

2006-07-01

Since the commercial operation of Kori Nuclear Power Plant unit 1 in April 1978, Korea has achieved rapid growth in its nuclear industry, and now has 20 operating nuclear power plants. As the design life of Kori unit 1 comes to an end, Korea Hydro and Nuclear Power Co., Ltd.(KHNP) is preparing for the continued operation of the plant for the first time in Korea. The feasibility of continued operation beyond design life has been already proven in many countries. Developed countries, such as the USA, England, Japan and so on, are also proceeding with the continued operation of NPPsmore » whose design life or license is due to expire, as long as the adequate safety and aging management review meet the acceptance criteria. Continued operation is absolutely needed for countries lacking in natural resources, such as Korea, in view of the efficient utilization of energy resources and reduction of greenhouse gases (CO{sub 2}) emission. For the continued operation beyond design life (30 yrs) of Kori unit 1, KHNP has performed Lifetime Management (PLiM) study, Periodic Safety Review (PSR), Probabilistic Safety Assessment (PSA) and Environmental Qualification (EQ), etc. and replaced main equipment, such as Steam Generators, Low Pressure Turbine Rotor, RCP Internals, Main Transformer, Main Generator, and so on. In September 2005, The Regulation of Atomic Energy Act in Korea was revised and published referring to License Renewal Rule of the USA. According to the revised regulations, KHNP is performing Life Assessment for Main Systems, Structures and Components (SSCs) and Radiological Impacts on the Environment with PSR for continued operation. (authors)« less

Development of an intelligent controller for power generators

NASA Astrophysics Data System (ADS)

Maxted, Clive; Waller, Winston

2005-01-01

This paper is a description of the development of an embedded controller for high power industrial diesel generators. The aim of the project was to replace the existing discrete logic design by an intelligent versatile and user configurable control system. A prototype embedded PC controlled system was developed, capable of fully replacing the existing system, with a colour TFT display and keypad. Features include fully automatic generator control as before with status and alarm display and monitoring of engine parameters, along with data logging, remote communications and a means of analysing data. The unit was tested on the bench and on diesel generators for the core controlling functionality to prove compliance with the specifications. The results of the testing proved the unit's suitability as a replacement for the existing system in its intended environment. The significance of this study is that a low cost replacement solution has been found for an industrial application by transferring modern technological knowledge to a small business. The company are now able to build on the design and take it into production, reducing servicing and production costs.

Peroxide-based oxygen generating topical wound dressing for enhancing healing of dermal wounds.

PubMed

Chandra, Prafulla K; Ross, Christina L; Smith, Leona C; Jeong, Seon S; Kim, Jaehyun; Yoo, James J; Harrison, Benjamin S

2015-01-01

Oxygen generating biomaterials represent a new trend in regenerative medicine that aims to generate and supply oxygen at the site of requirement, to support tissue healing and regeneration. To enhance the healing of dermal wounds, we have developed a highly portable, in situ oxygen generating wound dressings that uses sodium percarbonate (SPO) and calcium peroxide (CPO) as chemical oxygen sources. The dressing continuously generated oxygen for more than 3 days, after which it was replaced. In the in vivo testing on porcine full-thickness porcine wound model, the SPO/CPO dressing showed enhanced wound healing during the 8 week study period. Quantitative measurements of wound healing related parameters, such as wound closure, reepithelialization, epidermal thickness and collagen content of dermis showed that supplying oxygen topically using the SPO/CPO dressing significantly accelerated the wound healing. An increase in neovascularization, as determined using Von Willebrand factor (vWF) and CD31 staining, was also observed in the presence of SPO/CPO dressing. This novel design for a wound dressing that contains oxygen generating biomaterials (SPO/CPO) for supplying topical oxygen, may find utility in treating various types of acute to chronic wounds. © 2015 by the Wound Healing Society.

Plasmatic ion source

NASA Astrophysics Data System (ADS)

Semenov, A. P.

1986-02-01

A plasmatic ion source was built in which the hollow cathode above the two discharge chamber cathodes is readily replaced upon depletion after 250 to 300 h. The emission outlet hole is restored to original size by replacement of the cathode insert, while gas is continuously admitted by means of a spring mechanism. The source operates in the Penning discharge mode, with argon as the working gas. The hollow cathode is 36 mm long and has an inside diameter of 4 mm. The other two cathodes serve as pole shoes of a toroidal ferrite magnet which produces a longitudinal magnet field of 0.1 T induction in the discharge chamber. All three cathodes are made of magnetic steel and are insulated from cylindrical copper anode by teflon spacers. Heat is dissipated by oil, which carries it away to a water cooled housing compartment. The source generates an ion emission current of 20 mA with a discharge current of 200 mA at a pull voltage of 20kV.

Assessment of Eco-friendly Gases for Electrical Insulation to Replace the Most Potent Industrial Greenhouse Gas SF6.

PubMed

Rabie, Mohamed; Franck, Christian M

2018-01-16

Gases for electrical insulation are essential for the operation of electric power equipment. This Review gives a brief history of gaseous insulation that involved the emergence of the most potent industrial greenhouse gas known today, namely sulfur hexafluoride. SF 6 paved the way to space-saving equipment for the transmission and distribution of electrical energy. Its ever-rising usage in the electrical grid also played a decisive role in the continuous increase of atmospheric SF 6 abundance over the last decades. This Review broadly covers the environmental concerns related to SF 6 emissions and assesses the latest generation of eco-friendly replacement gases. They offer great potential for reducing greenhouse gas emissions from electrical equipment but at the same time involve technical trade-offs. The rumors of one or the other being superior seem premature, in particular because of the lack of dielectric, environmental, and chemical information for these relatively novel compounds and their dissociation products during operation.

Facing Global Challenges with Materials Innovation

NASA Astrophysics Data System (ADS)

Rizzo, Fernando

2017-10-01

The path of society evolution has long been associated with a growing demand for natural resources and continuous environmental degradation. During the last decades, this pace has accelerated considerably, despite the general concern with the legacy being left for the next generations. Looking ahead, the predicted growth of the world population, and the improvement of life conditions in most regions, point to an increasing demand for energy generation, resulting in additional pressure on the Earth's sustainability. Materials have had a key role in decreasing the use of natural resources, by either improving efficiency of existing technologies or enabling the development of radical new ones. The greenhouse effect (CO2 emissions) and the energy crisis are global challenges that can benefit from the development of new materials for the successful implementation of promising technologies and for the imperative replacement of fossil fuels by renewable sources.

Use of continuous renal replacement therapy in acute aluminum phosphide poisoning: a novel therapy.

PubMed

Nasa, Prashant; Gupta, Ankur; Mangal, Kishore; Nagrani, S K; Raina, Sanjay; Yadav, Rohit

2013-09-01

Aluminum phosphide is most common cause of poisoning in northern India. There is no specific antidote available and management of such cases is mainly supportive with high mortality. We present two cases of severe acute aluminium phosphide poisoning where continuous renal replacement therapy (CRRT) was started early along with other resuscitative measures and both the patients survived.

[The value of using administrative data in public health research: the Continuous Working Life Sample].

PubMed

López, María Andrée; Benavides, Fernando G; Alonso, Jordi; Espallargues, Mireia; Durán, Xavier; Martínez, José Miguel

2014-01-01

The use of administrative data is common practice in public health research. The present field note describes the Continuous Working Life Sample (CWLS) and its use in health research. The CWLS is built on records generated by all contacts with the social security system (work contracts, disability, etc.), plus tax data (monetary gains, income, etc.) and census data (level of education, country of birth, etc.), but does not allow individuals to be identified. The CWLS was started in 2004 with 4% (1.1 million persons) of the total population who were either contributors to or beneficiaries of the social security system. The information on the individuals in the CWLS is updated annually and lost individuals are replaced. This continuous design allows the construction of a cohort with information on working life and financial status and evaluation of their relationship with work disability. Future connection with clinical records would enable analysis of other health-related outcomes. Copyright © 2013 SESPAS. Published by Elsevier Espana. All rights reserved.

41 CFR 102-34.255 - What are motor vehicle replacement standards?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false What are motor vehicle... Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY 34-MOTOR VEHICLE MANAGEMENT Replacement of Motor Vehicles § 102-34.255 What are motor vehicle replacement standards? Motor...

40 CFR 141.84 - Lead service line replacement requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Lead service line replacement... PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.84 Lead service line replacement requirements. (a) Systems that fail to meet the lead action level in tap samples...

40 CFR 141.84 - Lead service line replacement requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Lead service line replacement... PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.84 Lead service line replacement requirements. (a) Systems that fail to meet the lead action level in tap samples...

40 CFR 141.84 - Lead service line replacement requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Lead service line replacement... PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.84 Lead service line replacement requirements. (a) Systems that fail to meet the lead action level in tap samples...

Third-generation pure alumina and alumina matrix composites in total hip arthroplasty: What is the evidence?

PubMed

Hannouche, Didier; Zingg, Matthieu; Miozzari, Hermes; Nizard, Remy; Lübbeke, Anne

2018-01-01

Wear, corrosion and periprosthetic osteolysis are important causes of failure in joint arthroplasty, especially in young patients.Ceramic bearings, developed 40 years ago, are an increasingly popular choice in hip arthroplasty. New manufacturing procedures have increased the strength and reliability of ceramic materials and reduced the risk of complications.In recent decades, ceramics made of pure alumina have continuously improved, resulting in a surgical-grade material that fulfills clinical requirements.Despite the track record of safety and long-term results, third-generation pure alumina ceramics are being replaced in clinical practice by alumina matrix composites, which are composed of alumina and zirconium.In this review, the characteristics of both materials are discussed, and the long-term results with third-generation alumina-on-alumina bearings and the associated complications are compared with those of other available ceramics. Cite this article: EFORT Open Rev 2018;3:7-14. DOI: 10.1302/2058-5241.3.170034.

75 FR 13320 - Florida Power Corporation, et al., Crystal River Unit 3 Nuclear Generating Plant; Environmental...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-19

... replacement outage that is currently underway at CR-3. In addition to steam generators, other large components (e.g., moisture separators and large heat exchangers) are being replaced during this outage... on the Internet at the NRC Web site: http://www.nrc.gov/reading-rm/adams.html . Persons who do not...

Magnetic water-in-water droplet microfluidics

NASA Astrophysics Data System (ADS)

Navi, Maryam; Abbasi, Niki; Tsai, Scott

2017-11-01

Aqueous two-phase systems (ATPS) have shown to be ideal candidates for replacing the conventional water-oil systems used in droplet microfluidics. We use an ATPS of Polyethylene Glycol (PEG) and Dextran (DEX) for microfluidic generation of magnetic water-in-water droplets. As ferrofluid partitions to DEX phase, there is no significant diffusion of ferrofluid at the interface of the droplets, rendering generation of magnetic DEX droplets in a non-magnetic continuous phase of PEG possible. In this system, both phases are water-based and highly biocompatible. We microfluidically generate magnetic DEX droplets at a flow-focusing junction in a jetting regime. We sort the droplets based on their size by placing a permanent magnet downstream of the droplet generation region, and show that the deflection of droplets is in good agreement with a mathematical model. We also show that the magnetic DEX droplets can be stabilized by lysozyme and be used for separation of single cell containing water-in-water droplets. This system of magnetic water-in-water droplet manipulation may find biomedical applications such as single-cell studies and drug delivery.

Surgical Approaches to Aortic Valve Replacement and Repair—Insights and Challenges

PubMed Central

Ramchandani, Mahesh; Reardon, Michael J

2014-01-01

Since 1960, surgical aortic valve replacement (sAVR) had been the only effective treatment for symptomatic severe aortic stenosis until the recent development of transcatheter aortic valve replacement (TAVR). TAVR has offered an alternative, minimally invasive treatment approach particularly for patients whose age or co-morbidities make them unsuitable for sAVR. The rapid and enthusiastic utilization of this new technique has triggered some speculation about the imminent demise of sAVR. We believe that despite the recent advances in TAVR, surgical approach to aortic valve replacement has continued to develop and will continue to be highly relevant in the future. This article will discuss the recent developments and current approaches for sAVR, and how these approaches will keep pace with catheter-based technologies. PMID:29588775

A comparison between fuel cells and other alternatives for marine electric power generation

NASA Astrophysics Data System (ADS)

Welaya, Yousri M. A.; El Gohary, M. Morsy; Ammar, Nader R.

2011-06-01

The world is facing a challenge in meeting its needs for energy. Global energy consumption in the last halfcentury has increased very rapidly and is expected to continue to grow over the next 50 years. However, it is expected to see significant differences between the last 50 years and the next. This paper aims at introducing a good solution to replace or work with conventional marine power plants. This includes the use of fuel cell power plant operated with hydrogen produced through water electrolysis or hydrogen produced from natural gas, gasoline, or diesel fuels through steam reforming processes to mitigate air pollution from ships.

Insertion of operation-and-indicate instructions for optimized SIMD code

DOEpatents

Eichenberger, Alexander E; Gara, Alan; Gschwind, Michael K

2013-06-04

Mechanisms are provided for inserting indicated instructions for tracking and indicating exceptions in the execution of vectorized code. A portion of first code is received for compilation. The portion of first code is analyzed to identify non-speculative instructions performing designated non-speculative operations in the first code that are candidates for replacement by replacement operation-and-indicate instructions that perform the designated non-speculative operations and further perform an indication operation for indicating any exception conditions corresponding to special exception values present in vector register inputs to the replacement operation-and-indicate instructions. The replacement is performed and second code is generated based on the replacement of the at least one non-speculative instruction. The data processing system executing the compiled code is configured to store special exception values in vector output registers, in response to a speculative instruction generating an exception condition, without initiating exception handling.

46 CFR 54.20-2 - Fabrication for hazardous materials (replaces UW-2(a)).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Fabrication for hazardous materials (replaces UW-2(a)). 54.20-2 Section 54.20-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-2 Fabrication for hazardous materials (replaces UW...

46 CFR 54.20-2 - Fabrication for hazardous materials (replaces UW-2(a)).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Fabrication for hazardous materials (replaces UW-2(a)). 54.20-2 Section 54.20-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-2 Fabrication for hazardous materials (replaces UW...

46 CFR 54.20-2 - Fabrication for hazardous materials (replaces UW-2(a)).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Fabrication for hazardous materials (replaces UW-2(a)). 54.20-2 Section 54.20-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-2 Fabrication for hazardous materials (replaces UW...

46 CFR 54.20-2 - Fabrication for hazardous materials (replaces UW-2(a)).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Fabrication for hazardous materials (replaces UW-2(a)). 54.20-2 Section 54.20-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-2 Fabrication for hazardous materials (replaces UW...

46 CFR 54.20-2 - Fabrication for hazardous materials (replaces UW-2(a)).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Fabrication for hazardous materials (replaces UW-2(a)). 54.20-2 Section 54.20-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-2 Fabrication for hazardous materials (replaces UW...

41 CFR 102-34.255 - What are motor vehicle replacement standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What are motor vehicle replacement standards? 102-34.255 Section 102-34.255 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY 34-MOTOR VEHICLE MANAGEMENT Replacement of Motor...

What Pacemakers Can Teach Us about the Ethics of Maintaining Artificial Organs.

PubMed

Hutchison, Katrina; Sparrow, Robert

2016-11-01

One day soon it may be possible to replace a failing heart, liver, or kidney with a long-lasting mechanical replacement or perhaps even with a 3-D printed version based on the patient's own tissue. Such artificial organs could make transplant waiting lists and immunosuppression a thing of the past. Supposing that this happens, what will the ongoing care of people with these implants involve? In particular, how will the need to maintain the functioning of artificial organs over an extended period affect patients and their doctors and the responsibilities of those who manufacture such devices? Drawing on lessons from the history of the cardiac pacemaker, this article offers an initial survey of the ethical issues posed by the need to maintain and service artificial organs. We briefly outline the nature and history of cardiac pacemakers, with a particular focus on the need for technical support, maintenance, and replacement of these devices. Drawing on the existing medical literature and on our conversations and correspondence with cardiologists, regulators, and manufacturers, we describe five sources of ethical issues associated with pacemaker maintenance: the location of the devices inside the human body, such that maintenance generates surgical risks; the complexity of the devices, which increases the risk of harms to patients as well as introducing potential injustices in access to treatment; the role of software-particularly software that can be remotely accessed-in the functioning of the devices, which generates privacy and security issues; the impact of continual development and improvement of the device; and the influence of commercial interests in the context of a medical device market in which there are several competing products. Finally, we offer some initial suggestions as to how these questions should be answered. © 2016 The Hastings Center.

Circadian hormone profiles and insulin sensitivity in patients with Addison's disease: a comparison of continuous subcutaneous hydrocortisone infusion with conventional glucocorticoid replacement therapy.

PubMed

Björnsdottir, Sigridur; Øksnes, Marianne; Isaksson, Magnus; Methlie, Paal; Nilsen, Roy M; Hustad, Steinar; Kämpe, Olle; Hulting, Anna-Lena; Husebye, Eystein S; Løvås, Kristian; Nyström, Thomas; Bensing, Sophie

2015-07-01

Conventional glucocorticoid replacement therapy in patients with Addison's disease (AD) is unphysiological with possible adverse effects on mortality, morbidity and quality of life. The diurnal cortisol profile can likely be restored by continuous subcutaneous hydrocortisone infusion (CSHI). The aim of this study was to compare circadian hormone rhythms and insulin sensitivity in conventional thrice-daily regimen of glucocorticoid replacement therapy with CSHI treatment in patients with AD. An open, randomized, two-period, 12-week crossover multicentre trial in Norway and Sweden. Ten Norwegian patients were admitted for 24-h sampling of hormone profiles. Fifteen Swedish patients underwent euglycaemic-hyperinsulinaemic clamp. Thrice-daily regimen of oral hydrocortisone (OHC) and CSHI treatment. We measured the circadian rhythm of cortisol, adrenocorticotropic hormone (ACTH), growth hormone (GH), insulin-like growth factor-1, (IGF-1), IGF-binding protein-3 (IGFBP-3), glucose, insulin and triglycerides during OHC and CSHI treatment. Euglycaemic-hyperinsulinaemic clamp was used to assess insulin sensitivity. Continuous subcutaneous hydrocortisone infusion provided a more physiological circadian cortisol curve including a late-night cortisol surge. ACTH levels showed a near normal circadian variation for CSHI. CSHI prevented a continuous decrease in glucose during the night. No difference in insulin sensitivity was observed between the two treatment arms. Continuous subcutaneous hydrocortisone infusion replacement re-established a circadian cortisol rhythm and normalized the ACTH levels. Patients with CSHI replacement had a more stable night-time glucose level compared with OHC without compromising insulin sensitivity. Thus, restoring night-time cortisol levels might be advantageous for patients with AD. © 2015 John Wiley & Sons Ltd.

Generator exchange is associated with an increased rate of Sprint Fidelis lead failure.

PubMed

Lovelock, Joshua D; Patel, Ayesha; Mengistu, Andenet; Hoskins, Michael; El-Chami, Mikhael; Lloyd, Michael S; Leon, Angel; DeLurgio, David; Langberg, Jonathan J

2012-10-01

The Medtronic Sprint Fidelis defibrillator lead is at an increased risk for failure and was recalled in October 2007. Approximately 268,000 leads were implanted, and more than 100,000 patients still have active Fidelis leads. A number of studies have examined the rate and clinical predictors of lead failure, but none has addressed the effect of an implantable cardioverter-defibrillator generator exchange on subsequent lead failure. Although the manufacturer asserts that "Sprint Fidelis performance after device change-out is similar to lead performance without device change-out," published data are lacking. To assess the effect of implantable cardioverter-defibrillator generator exchange on the rate of Fidelis lead failure. A chart review was conducted in patients who underwent implantation of a Fidelis lead. Patients with a functioning Fidelis lead at generator exchange were compared with controls with leads implanted for a comparable amount of time not undergoing ICD replacement. A total of 1366 patients received a Fidelis lead prior to the recall, of which 479 were still actively followed. Seventy-two patients with a functioning lead underwent generator exchange without lead replacement. Following generator replacement, 15 leads failed. Sixty percent of the Fidelis leads failed within 3 months. Generator exchange increased the rate of lead failure compared with matched controls (20.8% vs 2.54%; P < .001). Generator exchange is associated with a higher than expected rate of Fidelis lead failure, often within 3 months. The risk-benefit ratio of Fidelis lead replacement at the time of generator exchange may be greater than appreciated. Copyright © 2012 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Properties of fresh and hardened sustainable concrete due to the use of palm oil fuel ash as cement replacement

NASA Astrophysics Data System (ADS)

Hamada, Hussein M.; Jokhio, Gul Ahmed; Mat Yahaya, Fadzil; Humada, Ali M.

2018-04-01

Palm oil fuel ash (POFA) is a by-product resulting from the combustion of palm oil waste such as palm oil shell and empty fruit bunches to generate electricity in the palm oil mills. Considerable quantities of POFA thus generated, accumulate in the open fields and landfills, which causes atmospheric pollution in the form of generating toxic gases. Firstly, to protect the environment; and secondly, having excellent properties for this purpose; POFA can be and has been used as partial cement replacement in concrete preparation. Therefore, this paper compiles the results obtained from previous studies that address the properties of concrete containing POFA as cement replacement in fresh and hardened states. The results indicate that there is a great potential to using POFA as cement replacement because of its ability to improve compressive strength, reduce hydration heat of cement mortar and positively affect other fresh and hardened concrete properties. The paper recommends that conducting further studies to exploit high volume of POFA along with other additives as cement replacement while maintaining high quality of concrete can help minimize CO2 emissions due to concrete.

Wearable Fall Detector using Integrated Sensors and Energy Devices

NASA Astrophysics Data System (ADS)

Jung, Sungmook; Hong, Seungki; Kim, Jaemin; Lee, Sangkyu; Hyeon, Taeghwan; Lee, Minbaek; Kim, Dae-Hyeong

2015-11-01

Wearable devices have attracted great attentions as next-generation electronic devices. For the comfortable, portable, and easy-to-use system platform in wearable electronics, a key requirement is to replace conventional bulky and rigid energy devices into thin and deformable ones accompanying the capability of long-term energy supply. Here, we demonstrate a wearable fall detection system composed of a wristband-type deformable triboelectric generator and lithium ion battery in conjunction with integrated sensors, controllers, and wireless units. A stretchable conductive nylon is used as electrodes of the triboelectric generator and the interconnection between battery cells. Ethoxylated polyethylenimine, coated on the surface of the conductive nylon electrode, tunes the work function of a triboelectric generator and maximizes its performance. The electrical energy harvested from the triboelectric generator through human body motions continuously recharges the stretchable battery and prolongs hours of its use. The integrated energy supply system runs the 3-axis accelerometer and related electronics that record human body motions and send the data wirelessly. Upon the unexpected fall occurring, a custom-made software discriminates the fall signal and an emergency alert is immediately sent to an external mobile device. This wearable fall detection system would provide new opportunities in the mobile electronics and wearable healthcare.

Wearable Fall Detector using Integrated Sensors and Energy Devices.

PubMed

Jung, Sungmook; Hong, Seungki; Kim, Jaemin; Lee, Sangkyu; Hyeon, Taeghwan; Lee, Minbaek; Kim, Dae-Hyeong

2015-11-24

Wearable devices have attracted great attentions as next-generation electronic devices. For the comfortable, portable, and easy-to-use system platform in wearable electronics, a key requirement is to replace conventional bulky and rigid energy devices into thin and deformable ones accompanying the capability of long-term energy supply. Here, we demonstrate a wearable fall detection system composed of a wristband-type deformable triboelectric generator and lithium ion battery in conjunction with integrated sensors, controllers, and wireless units. A stretchable conductive nylon is used as electrodes of the triboelectric generator and the interconnection between battery cells. Ethoxylated polyethylenimine, coated on the surface of the conductive nylon electrode, tunes the work function of a triboelectric generator and maximizes its performance. The electrical energy harvested from the triboelectric generator through human body motions continuously recharges the stretchable battery and prolongs hours of its use. The integrated energy supply system runs the 3-axis accelerometer and related electronics that record human body motions and send the data wirelessly. Upon the unexpected fall occurring, a custom-made software discriminates the fall signal and an emergency alert is immediately sent to an external mobile device. This wearable fall detection system would provide new opportunities in the mobile electronics and wearable healthcare.

Successfully treated necrotizing fasciitis using extracorporeal life support combined with hemoadsorption device and continuous renal replacement therapy.

PubMed

Eid, Maroua; Fouquet, Olivier; Darreau, Cédric; Pierrot, Marc; Kouatchet, Achille; Mercat, Alain; Baufreton, Christophe

2018-03-01

Necrotizing fasciitis represents a life-threatening infectious condition that causes spreading necrotisis of superficial fascia and subcutaneous cellular tissues. We describe the case of a patient diagnosed with septic and toxic shocks leading to multiple organ failure successfully treated with a combination of extracorporeal life support, continuous renal replacement therapy, and a hemoadsorption device. A 41-year-old patient presented with necrotizing fasciitis and multi-organ failure. Initial extracorporeal life support therapy was implanted, compensating for systolic failure. Due to acute renal failure that persisted in time, continuous renal replacement therapy was added. Despite these treatments and as a last attempt to control the septic condition, a CytoSorb ® hemoadsorption device was installed in parallel to the extracorporeal life support circuit and two sessions were run. During the days following CytoSorb ® treatment, hemodynamic stabilization was observed, as well as normalization of lactic acidosis and blood parameters. This case describes the successful use of CytoSorb ® with continuous renal replacement therapy and extracorporeal life support in a combined way to overcome a critical phase of septic shock in a young adult patient. This combination of treatments turned out to be efficient for this patient in the context of necrotizing fasciitis.

Intensity of continuous renal-replacement therapy in critically ill patients.

PubMed

Bellomo, Rinaldo; Cass, Alan; Cole, Louise; Finfer, Simon; Gallagher, Martin; Lo, Serigne; McArthur, Colin; McGuinness, Shay; Myburgh, John; Norton, Robyn; Scheinkestel, Carlos; Su, Steve

2009-10-22

The optimal intensity of continuous renal-replacement therapy remains unclear. We conducted a multicenter, randomized trial to compare the effect of this therapy, delivered at two different levels of intensity, on 90-day mortality among critically ill patients with acute kidney injury. We randomly assigned critically ill adults with acute kidney injury to continuous renal-replacement therapy in the form of postdilution continuous venovenous hemodiafiltration with an effluent flow of either 40 ml per kilogram of body weight per hour (higher intensity) or 25 ml per kilogram per hour (lower intensity). The primary outcome measure was death within 90 days after randomization. Of the 1508 enrolled patients, 747 were randomly assigned to higher-intensity therapy, and 761 to lower-intensity therapy with continuous venovenous hemodiafiltration. Data on primary outcomes were available for 1464 patients (97.1%): 721 in the higher-intensity group and 743 in the lower-intensity group. The two study groups had similar baseline characteristics and received the study treatment for an average of 6.3 and 5.9 days, respectively (P=0.35). At 90 days after randomization, 322 deaths had occurred in the higher-intensity group and 332 deaths in the lower-intensity group, for a mortality of 44.7% in each group (odds ratio, 1.00; 95% confidence interval [CI], 0.81 to 1.23; P=0.99). At 90 days, 6.8% of survivors in the higher-intensity group (27 of 399), as compared with 4.4% of survivors in the lower-intensity group (18 of 411), were still receiving renal-replacement therapy (odds ratio, 1.59; 95% CI, 0.86 to 2.92; P=0.14). Hypophosphatemia was more common in the higher-intensity group than in the lower-intensity group (65% vs. 54%, P<0.001). In critically ill patients with acute kidney injury, treatment with higher-intensity continuous renal-replacement therapy did not reduce mortality at 90 days. (ClinicalTrials.gov number, NCT00221013.) 2009 Massachusetts Medical Society

Antiepileptic drug use by pregnant women enrolled in Florida Medicaid

PubMed Central

Meador, Kimford J.; Hartzema, Abraham

2015-01-01

Objective: The study aims were to investigate secular trends in antiepileptic drug (AED) use in women during pregnancy, and to compare the use of first- and second-generation AEDs. Methods: Study participants consisted of female Florida Medicaid beneficiaries, older than 15 years, and pregnant within the time period 1999 to 2009. Fifteen AEDs were categorized into first and second generation of AEDs. Continuous use of AEDs was defined as at least 2 consecutive AED prescriptions totaling more than a 30-day supply. Polytherapy was defined as 2 or more AEDs continuously used for at least 30 overlapping days. Annual prevalence was estimated and compared. Results: We included 2,099 pregnant women who were enrolled in Florida Medicaid from 1999 to 2009 and exposed to AEDs during pregnancy. Although there were fluctuations, overall AED use in the study cohort did not increase from 2000 to 2009 (β ± standard error [SE]: −0.07 ± 0.06, p = 0.31). The use of first-generation AEDs decreased (β ± SE: −6.21 ± 0.47, p < 0.0001), whereas the use of second-generation AEDs increased (β ± SE: 6.27 ± 0.52, p < 0.0001) from 2000 to 2009. AED use in polytherapy did not change through the study period. Valproate use reduced from 23% to 8% in the study population (β ± SE: −1.61 ± 0.36, p = 0.0019), but this decrease was only for women receiving an AED for epilepsy and was not present for other indications. Conclusion: The second-generation AEDs are replacing first-generation AEDs in both monotherapy and polytherapy. Valproate use has declined for epilepsy but not other indications. Additional changes in AED use are expected in future years. PMID:25653296

Antiepileptic drug use by pregnant women enrolled in Florida Medicaid.

PubMed

Wen, Xuerong; Meador, Kimford J; Hartzema, Abraham

2015-03-03

The study aims were to investigate secular trends in antiepileptic drug (AED) use in women during pregnancy, and to compare the use of first- and second-generation AEDs. Study participants consisted of female Florida Medicaid beneficiaries, older than 15 years, and pregnant within the time period 1999 to 2009. Fifteen AEDs were categorized into first and second generation of AEDs. Continuous use of AEDs was defined as at least 2 consecutive AED prescriptions totaling more than a 30-day supply. Polytherapy was defined as 2 or more AEDs continuously used for at least 30 overlapping days. Annual prevalence was estimated and compared. We included 2,099 pregnant women who were enrolled in Florida Medicaid from 1999 to 2009 and exposed to AEDs during pregnancy. Although there were fluctuations, overall AED use in the study cohort did not increase from 2000 to 2009 (β ± standard error [SE]: -0.07 ± 0.06, p = 0.31). The use of first-generation AEDs decreased (β ± SE: -6.21 ± 0.47, p < 0.0001), whereas the use of second-generation AEDs increased (β ± SE: 6.27 ± 0.52, p < 0.0001) from 2000 to 2009. AED use in polytherapy did not change through the study period. Valproate use reduced from 23% to 8% in the study population (β ± SE: -1.61 ± 0.36, p = 0.0019), but this decrease was only for women receiving an AED for epilepsy and was not present for other indications. The second-generation AEDs are replacing first-generation AEDs in both monotherapy and polytherapy. Valproate use has declined for epilepsy but not other indications. Additional changes in AED use are expected in future years. © 2015 American Academy of Neurology.

Renal replacement therapy in patients with severe precapillary pulmonary hypertension with acute right heart failure.

PubMed

Sztrymf, Benjamin; Prat, Dominique; Jacobs, Frédéric M; Brivet, François G; O'Callaghan, Dermot S; Price, Laura C; Jais, Xavier; Sitbon, Olivier; Simonneau, Gérald; Humbert, Marc

2013-01-01

Renal replacement therapy has been suggested as a therapeutic option in the setting of acute right ventricular failure in patients with severe precapillary pulmonary hypertension. However, there are few data supporting this strategy. To describe the clinical course and the prognosis of pulmonary hypertensive patients undergoing renal replacement therapy in the setting of acute right heart failure. This was a single-center retrospective study over an 11-year period. Data were collected from all patients with chronic precapillary pulmonary hypertension requiring catecholamine infusions for clinical worsening and acute kidney injury that necessitated renal replacement therapy. Fourteen patients were included. At admission, patients had a blood urea of 28.2 mmol/l (22.3-41.2), a creatinine level of 496 µmol/l (304-590), and a mean urine output in the 24 h preceding hospitalization of 200 ml (0-650). Sixty-eight renal replacement therapy sessions were performed, 36 of which were continuous and 32 of which were intermittent. Systemic hypotension occurred in 16/32 intermittent and 16/36 continuous sessions (p = 0.9). Two patients died during a continuous session. The intensive care unit-related, 1-, and 3-month mortality was 46.7, 66.7, and 73.3%, respectively. Renal replacement therapy is feasible in the setting of acute right ventricular failure in patients with severe precapillary pulmonary hypertension but is associated with a poor prognosis. The best modality and timing in this population remain to be defined. Copyright © 2012 S. Karger AG, Basel.

Replacing The Engine In Your Car While You Are Still Driving It [PowerPoint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bjorklund, Eric A.

The scope of the project included the following: install new network backbone, replace 201 MHz rf tubes, replace low-level rf system, replace timing system, replace industrial I/O system, replace beam synchronous data acquisition system, replace fast protect reporting system, new wire scanner hardware, and new beam position/phase monitor hardware--all of this to be done while continuing to deliver beam to users. Lessons learned, for anyone contemplating a similarly ambitious upgrade: You can’t replace the whole system at once. Some compatibility must be maintained between the old and new systems. Always have a way to fall back. Have sympathy for themore » operations staff. You will be surprised.« less

46 CFR 56.97-35 - Pneumatic tests (replaces 137.5).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Pneumatic tests (replaces 137.5). 56.97-35 Section 56.97-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Pressure Tests § 56.97-35 Pneumatic tests (replaces 137.5). (a) General Requirements. When a pneumatic test is performed, it...

46 CFR 53.01-10 - Service restrictions and exceptions (replaces HG-101).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Service restrictions and exceptions (replaces HG-101). 53.01-10 Section 53.01-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. The service restriction...

46 CFR 53.01-10 - Service restrictions and exceptions (replaces HG-101).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Service restrictions and exceptions (replaces HG-101). 53.01-10 Section 53.01-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. The service restriction...

46 CFR 53.01-10 - Service restrictions and exceptions (replaces HG-101).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Service restrictions and exceptions (replaces HG-101). 53.01-10 Section 53.01-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. The service restriction...

46 CFR 53.01-10 - Service restrictions and exceptions (replaces HG-101).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Service restrictions and exceptions (replaces HG-101). 53.01-10 Section 53.01-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. The service restriction...

46 CFR 53.01-10 - Service restrictions and exceptions (replaces HG-101).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Service restrictions and exceptions (replaces HG-101). 53.01-10 Section 53.01-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-10 Service restrictions and exceptions (replaces HG-101). (a) General. The service restriction...

Slab replacement maturity guidelines : [summary].

DOT National Transportation Integrated Search

2014-04-01

Concrete sets in hours at moderate temperatures, : but the bonds that make concrete strong continue : to mature over days to years. However, for : replacement concrete slabs on highways, it is : crucial that concrete develop enough strength : within ...

Calculating evidence-based renal replacement therapy - Introducing an excel-based calculator to improve prescribing and delivery in renal replacement therapy - A before and after study.

PubMed

Cottle, Daniel; Mousdale, Stephen; Waqar-Uddin, Haroon; Tully, Redmond; Taylor, Benjamin

2016-02-01

Transferring the theoretical aspect of continuous renal replacement therapy to the bedside and delivering a given "dose" can be difficult. In research, the "dose" of renal replacement therapy is given as effluent flow rate in ml kg -1  h -1 . Unfortunately, most machines require other information when they are initiating therapy, including blood flow rate, pre-blood pump flow rate, dialysate flow rate, etc. This can lead to confusion, resulting in patients receiving inappropriate doses of renal replacement therapy. Our aim was to design an excel calculator which would personalise patient's treatment, deliver an effective, evidence-based dose of renal replacement therapy without large variations in practice and prolong filter life. Our calculator prescribes a haemodialfiltration dose of 25 ml kg -1  h -1 whilst limiting the filtration fraction to 15%. We compared the episodes of renal replacement therapy received by a historical group of patients, by retrieving their data stored on the haemofiltration machines, to a group where the calculator was used. In the second group, the data were gathered prospectively. The median delivered dose reduced from 41.0 ml kg -1  h -1 to 26.8 ml kg -1  h -1 with reduced variability that was significantly closer to the aim of 25 ml kg -1 .h -1 ( p  < 0.0001). The median treatment time increased from 8.5 h to 22.2 h ( p  = 0.00001). Our calculator significantly reduces variation in prescriptions of continuous veno-venous haemodiafiltration and provides an evidence-based dose. It is easy to use and provides personal care for patients whilst optimizing continuous veno-venous haemodiafiltration delivery and treatment times.

Continuous tooth replacement: the possible involvement of epithelial stem cells.

PubMed

Huysseune, Ann; Thesleff, Irma

2004-06-01

Epithelial stem cells have been identified in integumental structures such as hairs and continuously growing teeth of various rodents, and in the gut. Here we propose the involvement of epithelial stem cells in the continuous tooth replacement that characterizes non-mammalian vertebrates, as exemplified by the zebrafish. Arguments are based on morphological observations of tooth renewal in the zebrafish and on the similarities between molecular control of hair and tooth formation. Dissection of the molecular cascades underlying the regulation of the epithelial stem cell niche might open perspectives for new regenerative treatment strategies in clinical dentistry. Copyright 2004 Wiley Periodicals, Inc.

10 CFR 830 Major Modification Determination for the ATR Diesel Bus (E-3) and Switchgear Replacement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noel Duckwtiz

2011-05-01

Near term replacement of aging and obsolescent original ATR equipment has become important to ensure ATR capability in support of NE’s long term national missions. To that end, a mission needs statement has been prepared for a non-major system acquisition which is comprised of three interdependent subprojects. The first project, subject of this determination, will replace the existent diesel-electrical bus (E-3) and associated switchgear. More specifically, INL proposes transitioning ATR to 100% commercial power with appropriate emergency backup to include: • Provide commercial power as the normal source of power to the ATR loads currently supplied by diesel-electric power. •more » Provide backup power to the critical ATR loads in the event of a loss of commercial power. • Replace obsolescent critical ATR power distribution equipment, e.g., switchgear, transformers, motor control centers, distribution panels. Completion of this and two other age-related projects (primary coolant pump and motor replacement and emergency firewater injection system replacement) will resolve major age related operational issues plus make a significant contribution in sustaining the ATR safety and reliability profile. The major modification criteria evaluation of the project pre-conceptual design identified several issues make the project a major modification: 1. Evaluation Criteria #2 (Footprint change). The addition of a new PC-4 structure to the ATR Facility to house safety-related SSCs requires careful attention to maintaining adherence to applicable engineering and nuclear safety design criteria (e.g., structural qualification, fire suppression) to ensure no adverse impacts to the safety-related functions of the housed equipment. 2. Evaluation Criteria #3 (Change of existing process). The change to the strategy for providing continuous reliable power to the safety-related emergency coolant pumps requires careful attention and analysis to ensure it meets a project primary object to maintain or reduce CDF and does not negatively affect the efficacy of the currently approved strategy. 3. Evaluation Criteria #5 (Create the need for new or revised safety SSCs). The change to the strategy for providing continuous reliable power to the safety-related emergency coolant pumps, based on the pre-conceptual design, will require the addition of two quick start diesel generators, their associated power coordination/distribution controls, and a UPS to the list of safety-related SSCs. Similarly to item 1 above, the addition of these active SSCs to the list of safety-related SSCs and replacement of the E-3 bus requires careful attention to maintaining adherence to applicable engineering and nuclear safety design criteria (e.g., seismic qualification, isolation of redundant trains from common fault failures) to ensure no adverse impacts to the safety-related functions.« less

Heated, humidified high-flow nasal cannula therapy: yet another way to deliver continuous positive airway pressure?

PubMed

Kubicka, Zuzanna J; Limauro, Joseph; Darnall, Robert A

2008-01-01

The goal was to estimate the level of delivered continuous positive airway pressure by measuring oral cavity pressure with the mouth closed in infants of various weights and ages treated with heated, humidified high-flow nasal cannula at flow rates of 1-5 L/minute. We hypothesized that clinically relevant levels of continuous positive airway pressure would not be achieved if a nasal leak is maintained. After performing bench measurements and demonstrating that oral cavity pressure closely approximated levels of traditionally applied nasal continuous positive airway pressure, we successfully measured oral cavity pressure during heated, humidified, high-flow nasal cannula treatment in 27 infants. Small (outer diameter: 0.2 cm) cannulae were used for all infants, and flow rates were left as ordered by providers. Bench measurements showed that, for any given leak size, there was a nearly linear relationship between flow rate and pressure. The highest pressure achieved was 4.5 cmH2O (flow rate: 8 L/minute; leak: 3 mm). In our study infants (postmenstrual age: 29.1-44.7 weeks; weight: 835-3735 g; flow rate: 1-5 L/minute), no pressure was generated with the mouth open at any flow rate. With the mouth closed, the oral cavity pressure was related to both flow rate and weight. For infants of < or = 1500 g, there was a linear relationship between flow rate and oral cavity pressure. Oral cavity pressure can estimate the level of continuous positive airway pressure. Continuous positive airway pressure generated with heated, humidified, high-flow nasal cannula treatment depends on the flow rate and weight. Only in the smallest infants with the highest flow rates, with the mouth fully closed, can clinically significant but unpredictable levels of continuous positive airway pressure be achieved. We conclude that heated, humidified high-flow nasal cannula should not be used as a replacement for delivering continuous positive airway pressure.

Characteristics of electromagnetic interference generated during discharge of Mylar samples. [spacecraft-environment interaction simulation

NASA Technical Reports Server (NTRS)

Leung, P. L.

1984-01-01

This paper discusses the measurements of the electromagnetic interference (EMI) generated during discharges of Mylar samples. The two components of EMI, the conducted emission and the radiated emission, are characterized by the replacement current and the radiated RF spectrum respectively. The measured radiated RF spectra reveal important information on the source of the electromagnetic radiation. The possible sources are the replacement current pulse and the discharged generated plasma. The scaling of the amplitudes of the EMI, as a function of the area of the test sample, is also discussed.

Nursing issues in renal replacement therapy: organization, manpower assessment, competency evaluation and quality improvement processes.

PubMed

Graham, Patricia; Lischer, Eileen

2011-01-01

For the patient with acute kidney injury, continuous renal replacement therapy (CRRT) is a treatment option that has application for the hemodynamically unstable critically ill patient. The decision to initiate a continuous renal replacement modality depends not only on the physician, either the nephrologist or intensivist, but also on the availability of specially trained nursing resources. This article will explore the nursing collaborative model of care at a large university-based research and teaching Medical Center in Southern California. The focus will be on nursing issues in CRRT including organization of educational programs, manpower assessment, competency evaluation, and quality improvement processes. © 2011 Wiley Periodicals, Inc.

46 CFR 67.503 - Application for exchange or replacement of a Certificate of Documentation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Application for exchange or replacement of a Certificate of Documentation. 67.503 Section 67.503 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND MEASUREMENT OF VESSELS DOCUMENTATION OF VESSELS Fees § 67.503 Application for exchange or replacement of a Certificate of...

46 CFR 54.05-1 - Scope (replaces UG-84).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Scope (replaces UG-84). 54.05-1 Section 54.05-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Toughness Tests § 54.05-1 Scope (replaces UG-84). The toughness tests of materials used in pressure vessels shall be as required by this subpart in lieu of...

46 CFR 54.05-1 - Scope (replaces UG-84).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Scope (replaces UG-84). 54.05-1 Section 54.05-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Toughness Tests § 54.05-1 Scope (replaces UG-84). The toughness tests of materials used in pressure vessels shall be as required by this subpart in lieu of...

46 CFR 54.05-1 - Scope (replaces UG-84).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Scope (replaces UG-84). 54.05-1 Section 54.05-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Toughness Tests § 54.05-1 Scope (replaces UG-84). The toughness tests of materials used in pressure vessels shall be as required by this subpart in lieu of...

46 CFR 54.05-1 - Scope (replaces UG-84).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Scope (replaces UG-84). 54.05-1 Section 54.05-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Toughness Tests § 54.05-1 Scope (replaces UG-84). The toughness tests of materials used in pressure vessels shall be as required by this subpart in lieu of...

46 CFR 54.05-1 - Scope (replaces UG-84).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Scope (replaces UG-84). 54.05-1 Section 54.05-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Toughness Tests § 54.05-1 Scope (replaces UG-84). The toughness tests of materials used in pressure vessels shall be as required by this subpart in lieu of...

BCI`S domestic automotive replacement battery shipments by channel of distribution

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-07-01

Thirteen manufacturing members, of Battery Council International, supplied the shipment figures contained in this report. This Channel of Distribution continues to account for an estimated 97% of the domestic replacement battery industry. This report indicates solely domestic replacement battery shipments for the following battery classifications: passenger car & light commercial; heavy duty commercial; special tractor; marine; general utility and golf car.

Latest-Generation Transcatheter Aortic Valve Replacement Devices and Procedures.

PubMed

Chamandi, Chekrallah; Puri, Rishi; Rodriguez-Gabella, Tania; Rodés-Cabau, Josep

2017-09-01

Transcatheter aortic valve replacement (TAVR) is a well-established treatment for patients with severe symptomatic aortic stenosis who are at high or prohibitive surgical risk. More recently, TAVR has emerged as a valid alternative to surgical aortic valve replacement for treating intermediate-risk patients, and several studies are currently evaluating the role of TAVR in low-risk patients. Transcatheter heart valve (THV) technologies have evolved considerably over time, and important iterations have been implemented in many of the latest-generation devices to (1) reduce the size and improve delivery system properties; (2) improve valve deployment, repositioning, and retrievability; and (3) reduce paravalvular leaks. This article reviews the main characteristics of, and clinical results associated with, the newer-generation THVs while providing an overview of novel TAVR indications. Copyright © 2017 Canadian Cardiovascular Society. Published by Elsevier Inc. All rights reserved.

Slow continuous renal replacement therapies: an update.

PubMed

Kes, P

2000-01-01

Continuous renal replacement therapies (CRRT) are now being used by nephrologists, intensivists, and anesthesiologists. The various CRRT modalities differ in the kind of vascular access, the application of diffusive or convective clearances (or a combination of both), and in the location where the replacement fluid enters the circuit. CRRTs have certainly made the management of critically ill patients with acute renal failure (ARF) combined with cardiovascular instability, severe fluid overload, hypercatabolism, cerebral edema, adult respiratory distress syndrome, lactic acidosis, sepsis or other inflammatory syndromes, crush syndrome, congestive heart failure, and cardiopulmonary bypass easier. Continuous therapies incorporate several advantages including improved hemodynamic stability, optimal fluid balance, gradual urea removal, elimination of septic mediators, and the possibility of unlimited parenteral nutrition. Major difficulties and unsolved problems of CRRT are the ongoing necessity of continuous anticoagulation, considerable loss of amino acids, vitamins, trace elements, potassium, phosphate, and some drugs, as well as immobilization of the patient. The advantages of CRRT should theoretically translate into improved outcomes of critically ill ARF patients, but the superiority of continuous modalities in terms of outcome is still controversial, despite encouraging results in some clinical trials. Currently used CRRT with sophisticated treatment devices has become more expensive than hemodialysis, but the cost cannot be used as an argument against the continuous treatment modalities.

Electrostatic Hazard Considerations for ODC Solvent Replacement Selection Testing

NASA Technical Reports Server (NTRS)

Fairbourn, Brad

1999-01-01

ODC solvents are used to clean many critical substrates during solid rocket motor production operations. Electrostatic charge generation incidental to these cleaning operations can pose a major safety issue. Therefore, while determining the acceptability of various ODC replacement cleaners, one aspect of the selection criteria included determining the extent of electric charge generation during a typical solvent cleaning operation. A total of six candidate replacement cleaners, sixteen critical substrates, and two types of cleaning swatch materials were studied in simulated cleaning operations. Charge generation and accumulation effects were investigated by measuring the peak voltage and brush discharging effects associated with each cleaning process combination. In some cases, charge generation was found to be very severe. Using the conductivity information for each cleaner, the peak voltage data could in some cases, be qualitatively predicted. Test results indicated that severe charging effects could result in brush discharges that could potentially result in flash fire hazards when occurring in close proximity to flammable vapor/air mixtures. Process controls to effectively mitigate these hazards are discussed.

Novel synthetic Medea selfish genetic elements drive population replacement in Drosophila; a theoretical exploration of Medea-dependent population suppression.

PubMed

Akbari, Omar S; Chen, Chun-Hong; Marshall, John M; Huang, Haixia; Antoshechkin, Igor; Hay, Bruce A

2014-12-19

Insects act as vectors for diseases of plants, animals, and humans. Replacement of wild insect populations with genetically modified individuals unable to transmit disease provides a potentially self-perpetuating method of disease prevention. Population replacement requires a gene drive mechanism in order to spread linked genes mediating disease refractoriness through wild populations. We previously reported the creation of synthetic Medea selfish genetic elements able to drive population replacement in Drosophila. These elements use microRNA-mediated silencing of myd88, a maternally expressed gene required for embryonic dorso-ventral pattern formation, coupled with early zygotic expression of a rescuing transgene, to bring about gene drive. Medea elements that work through additional mechanisms are needed in order to be able to carry out cycles of population replacement and/or remove existing transgenes from the population, using second-generation elements that spread while driving first-generation elements out of the population. Here we report the synthesis and population genetic behavior of two new synthetic Medea elements that drive population replacement through manipulation of signaling pathways involved in cellular blastoderm formation or Notch signaling, demonstrating that in Drosophila Medea elements can be generated through manipulation of diverse signaling pathways. We also describe the mRNA and small RNA changes in ovaries and early embryos associated from Medea-bearing females. Finally, we use modeling to illustrate how Medea elements carrying genes that result in diapause-dependent female lethality could be used to bring about population suppression.

Mechanistic Studies on the Galvanic Replacement Reaction between Multiply Twinned Particles of Ag and HAuCl4 in an Organic Medium

PubMed Central

Lu, Xianmao; Tuan, Hsing-Yu; Chen, Jingyi; Li, Zhi-Yuan; Korgel, Brian A; Xia, Younan

2008-01-01

This article presents a mechanistic study on the galvanic replacement reaction between 11- and 14-nm multiply twinned particles (MTPs) of Ag and HAuCl4 in chloroform. We monitored both morphological and spectral changes as the molar ratio of HAuCl4 to Ag was increased. The details of reaction were different from previous observations on single-crystal Ag nanocubes and cubooctahedrons. Because Au and Ag form alloys rapidly within small MTPs rich in vacancy and grain boundary defects, a complete Au shell did not form on the surface of each individual Ag template. Instead, the replacement reaction resulted in the formation of alloy nanorings and nanocages from Ag MTPs of decahedral or icosahedral shape. For the nanorings and nanocages derived from 11-nm Ag MTPs, the surface plasmon resonance (SPR) peak can be continuously shifted from 400 to 616 nm. When the size of Ag MTPs was increased to 14 nm, the SPR peak can be further shifted to 740 nm, a wavelength sought by biomedical applications. We have also investigated the effects of capping ligands and AgCl precipitate on the replacement reaction. While hollow structures were routinely generated from oleylamine-capped Ag MTPs, we obtained very few hollow structures by using a stronger capping ligand such as oleic acid or tri-n-octylphosphine oxide (TOPO). Addition of extra oleylamine was found to be critical to the formation of well-controlled, uniform hollow structures free of AgCl contamination thanks to the formation of a soluble complex between AgCl and oleylamine. PMID:17243691

Design optimization of large-size format edge-lit light guide units

NASA Astrophysics Data System (ADS)

Hastanin, J.; Lenaerts, C.; Fleury-Frenette, K.

2016-04-01

In this paper, we present an original method of dot pattern generation dedicated to large-size format light guide plate (LGP) design optimization, such as photo-bioreactors, the number of dots greatly exceeds the maximum allowable number of optical objects supported by most common ray-tracing software. In the proposed method, in order to simplify the computational problem, the original optical system is replaced by an equivalent one. Accordingly, an original dot pattern is splitted into multiple small sections, inside which the dot size variation is less than the ink dots printing typical resolution. Then, these sections are replaced by equivalent cells with continuous diffusing film. After that, we adjust the TIS (Total Integrated Scatter) two-dimensional distribution over the grid of equivalent cells, using an iterative optimization procedure. Finally, the obtained optimal TIS distribution is converted into the dot size distribution by applying an appropriate conversion rule. An original semi-empirical equation dedicated to rectangular large-size LGPs is proposed for the initial guess of TIS distribution. It allows significantly reduce the total time needed to dot pattern optimization.

Integrated, Continuous Emulsion Creamer.

PubMed

Cochrane, Wesley G; Hackler, Amber L; Cavett, Valerie J; Price, Alexander K; Paegel, Brian M

2017-12-19

Automated and reproducible sample handling is a key requirement for high-throughput compound screening and currently demands heavy reliance on expensive robotics in screening centers. Integrated droplet microfluidic screening processors are poised to replace robotic automation by miniaturizing biochemical reactions to the droplet scale. These processors must generate, incubate, and sort droplets for continuous droplet screening, passively handling millions of droplets with complete uniformity, especially during the key step of sample incubation. Here, we disclose an integrated microfluidic emulsion creamer that packs ("creams") assay droplets by draining away excess oil through microfabricated drain channels. The drained oil coflows with creamed emulsion and then reintroduces the oil to disperse the droplets at the circuit terminus for analysis. Creamed emulsion assay incubation time dispersion was 1.7%, 3-fold less than other reported incubators. The integrated, continuous emulsion creamer (ICEcreamer) was used to miniaturize and optimize measurements of various enzymatic activities (phosphodiesterase, kinase, bacterial translation) under multiple- and single-turnover conditions. Combining the ICEcreamer with current integrated microfluidic DNA-encoded library bead processors eliminates potentially cumbersome instrumentation engineering challenges and is compatible with assays of diverse target class activities commonly investigated in drug discovery.

Development of an accurate fluid management system for a pediatric continuous renal replacement therapy device

PubMed Central

SANTHANAKRISHNAN, ARVIND; NESTLE, TRENT T.; MOORE, BRIAN L.; YOGANATHAN, AJIT P.; PADEN, MATTHEW L.

2013-01-01

Acute kidney injury is common in critically ill children and renal replacement therapies provide a life saving therapy to a subset of these children. However, there is no Food and Drug Administration approved device to provide pediatric continuous renal replacement therapy (CRRT). Consequently, clinicians adapt approved adult CRRT devices for use in children due to lack of safer alternatives. Complications occur using adult CRRT devices in children due to inaccurate fluid balance (FB) between the volumes of ultrafiltrate (UF) removed and replacement fluid (RF) delivered. We demonstrate the design and validation of a pediatric fluid management system for obtaining accurate instantaneous and cumulative FB. Fluid transport was achieved via multiple novel pulsatile diaphragm pumps. The conservation of volume principle leveraging the physical property of fluid incompressibility along with mechanical coupling via a crankshaft was used for FB. Accuracy testing was conducted in vitro for 8-hour long continuous operation of the coupled UF and RF pumps. The mean cumulative FB error was <1% across filtration flows from 300 mL/hour to 3000 mL/hour. This approach of FB control in a pediatric specific CRRT device would represent a significant accuracy improvement over currently used clinical implementations. PMID:23644618

Tooth replacement without a dental lamina: the search for epithelial stem cells in Polypterus senegalus.

PubMed

Vandenplas, Sam; De Clercq, Adelbert; Huysseune, Ann

2014-07-01

Most actinopterygians replace their teeth continuously throughout life. To address the question of where and how replacement teeth form in actinopterygians, it is advisable to investigate well-chosen representatives within the lineage. The African bichir, Polypterus senegalus, belongs to the earliest diverged group of the actinopterygian lineage with currently living representatives. Its well characterized dentition, together with its phylogenetic position, make this species an attractive model to answer following questions: (1) when and where does the replacement tooth form and how is it connected with the dental organ of the predecessor, and (2) is there any evidence for the presence of epithelial stem cells, hypothesized to play a role in replacement? Serial sections show that one tooth family can contain up to three members, which are all interconnected by dental epithelium. Replacement teeth develop without the presence of a successional dental lamina. We propose that this is the plesiomorphic condition for tooth replacement in actinopterygians. BrdU pulse-chase experiments reveal cells in the outer and middle dental epithelium, proliferating at the time of initiation of a new replacement tooth. It is tempting to assume that these cell layers provide a stem cell niche. The observed absence of label-retaining cells after long chase times (up to 8 weeks) is held against the light of divergent views on cell cycling properties of stem cells. At present, our data do not support, neither reject, the hypothesis on involvement of epithelial stem cells within the process of continuous tooth replacement. © 2014 Wiley Periodicals, Inc.

Strength and Microstructure of Concrete with Iron Ore Tailings as Replacement for River Sand

NASA Astrophysics Data System (ADS)

Umara Shettima, Ali; Ahmad, Yusof; Warid Hussin, Mohd; Zakari Muhammad, Nasiru; Eziekel Babatude, Ogunbode

2018-03-01

River Sand is one of the basic ingredients used in the production of concrete. Consequently, continuous consumption of sand in construction industry contributes significantly to depletion of natural resources. To achieve more sustainable construction materials, this paper reports the use of iron ore tailings (IOT) as replacement for river sand in concrete production. IOT is a waste product generated from the production of iron ore and disposed to land fill without any economic value. Concrete mixtures containing different amount of IOT were designed for grade C30 with water to cement ratio of 0.60. The percentage ratios of the river sand replacements by IOT were 25%, 50%, 75% and 100%. Concrete microstructure test namely, XRD and Field Emission Scanned Electron Microscopic/Energy dispersive X-ray Spectroscopy (FESEM/EDX) were conducted for control and IOT concretes in order to determine the interaction and performance of the concrete containing IOT. Test results indicated that the slump values of 130 mm and 80 to 110 mm were recorded for the control and IOT concretes respectively. The concrete sample of 50% IOT recorded the highest compressive strength of 37.7 MPa at 28 days, and the highest flexural strength of 5.5 MPa compared to 4.7 MPa for reference concrete. The texture of the IOT is rough and angular which was able to improve the strength of the concrete.

Effect of prolonged coldness on survival and fertility of Drosophila melanogaster.

PubMed

Mockett, Robin J; Matsumoto, Yuri

2014-01-01

The laboratory fruit fly, Drosophila melanogaster, is used widely in biological research, but the requirement to maintain stocks with a roughly biweekly generation time imposes substantial burdens of labor, potential cross-contamination and mutation accumulation. The purpose of this study was to assess the impact of prolonged cold stress or milder cooling on survivorship and fertility. The hypothesis was that cold storage would result in postponement of reproduction and a longer generation time. Flies of several genotypes were maintained continuously at 4-11 °C; recovery rates and subsequent yields of adult progeny were recorded. Adults and pupae of a relatively long-lived y w lineage were more resistant to severe cold stress than embryos and larvae. Adults exhibited minimal mortality up to at least 5 d at 4 °C, 20 d at 8 °C and 12 weeks at 11 °C. Reproduction did not occur at these temperatures, but progeny were obtained after recovery at 25 °C. At all temperatures, chilling caused a rapid, severe and progressive decrease in fertility during the first 2 d of recovery. The impact on fertility during the subsequent 2-4 d was much milder and it occurred only after prolonged incubation at low temperatures. The total reproductive output during the first 6 d of recovery was sufficient to replace the parental population after 12 weeks at 11 °C. Food spoilage had an unexpectedly low impact on survivorship and fertility, and the reproductive output of F1 progeny was not affected by storing parental flies at 11 °C for 8-10 weeks. In the case of w1118 flies, replacement of the parents within 6 d of recovery was possible for up to 60 d at 11 °C. Among less fertile genotypes, replacement of the parents was possible within 18 d after 4-10 weeks at 11 °C. These results show that the 2-week maintenance interval of stocks of D. melanogaster can be extended 3-7 fold, at least for 1 generation, by storing adult flies at 11 °C.

Effect of Prolonged Coldness on Survival and Fertility of Drosophila melanogaster

PubMed Central

Mockett, Robin J.; Matsumoto, Yuri

2014-01-01

The laboratory fruit fly, Drosophila melanogaster, is used widely in biological research, but the requirement to maintain stocks with a roughly biweekly generation time imposes substantial burdens of labor, potential cross-contamination and mutation accumulation. The purpose of this study was to assess the impact of prolonged cold stress or milder cooling on survivorship and fertility. The hypothesis was that cold storage would result in postponement of reproduction and a longer generation time. Flies of several genotypes were maintained continuously at 4–11°C; recovery rates and subsequent yields of adult progeny were recorded. Adults and pupae of a relatively long-lived y w lineage were more resistant to severe cold stress than embryos and larvae. Adults exhibited minimal mortality up to at least 5 d at 4°C, 20 d at 8°C and 12 weeks at 11°C. Reproduction did not occur at these temperatures, but progeny were obtained after recovery at 25°C. At all temperatures, chilling caused a rapid, severe and progressive decrease in fertility during the first 2 d of recovery. The impact on fertility during the subsequent 2–4 d was much milder and it occurred only after prolonged incubation at low temperatures. The total reproductive output during the first 6 d of recovery was sufficient to replace the parental population after 12 weeks at 11°C. Food spoilage had an unexpectedly low impact on survivorship and fertility, and the reproductive output of F1 progeny was not affected by storing parental flies at 11°C for 8–10 weeks. In the case of w 1118 flies, replacement of the parents within 6 d of recovery was possible for up to 60 d at 11°C. Among less fertile genotypes, replacement of the parents was possible within 18 d after 4–10 weeks at 11°C. These results show that the 2-week maintenance interval of stocks of D. melanogaster can be extended 3–7 fold, at least for 1 generation, by storing adult flies at 11°C. PMID:24632815

Merging Bottom-Up with Top-Down: Continuous Lamellar Networks and Block Copolymer Lithography

NASA Astrophysics Data System (ADS)

Campbell, Ian Patrick

Block copolymer lithography is an emerging nanopatterning technology with capabilities that may complement and eventually replace those provided by existing optical lithography techniques. This bottom-up process relies on the parallel self-assembly of macromolecules composed of covalently linked, chemically distinct blocks to generate periodic nanostructures. Among the myriad potential morphologies, lamellar structures formed by diblock copolymers with symmetric volume fractions have attracted the most interest as a patterning tool. When confined to thin films and directed to assemble with interfaces perpendicular to the substrate, two-dimensional domains are formed between the free surface and the substrate, and selective removal of a single block creates a nanostructured polymeric template. The substrate exposed between the polymeric features can subsequently be modified through standard top-down microfabrication processes to generate novel nanostructured materials. Despite tremendous progress in our understanding of block copolymer self-assembly, continuous two-dimensional materials have not yet been fabricated via this robust technique, which may enable nanostructured material combinations that cannot be fabricated through bottom-up methods. This thesis aims to study the effects of block copolymer composition and processing on the lamellar network morphology of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) and utilize this knowledge to fabricate continuous two-dimensional materials through top-down methods. First, block copolymer composition was varied through homopolymer blending to explore the physical phenomena surrounding lamellar network continuity. After establishing a framework for tuning the continuity, the effects of various processing parameters were explored to engineer the network connectivity via defect annihilation processes. Precisely controlling the connectivity and continuity of lamellar networks through defect engineering and optimizing the block copolymer lithography process thus enabled the top-down fabrication of continuous two-dimensional gold networks with nanoscale properties. The lamellar structure of these networks was found to confer unique mechanical properties on the nanowire networks and suggests that materials templated via this method may be excellent candidates for integration into stretchable and flexible devices.

JSF/F-35 Pollution Prevention Activities

DTIC Science & Technology

2006-05-01

Liquid Oxygen •Produces Oxygen-Rich Breathing Gas From Engine Bleed Air Using Molecular Sieve Technology •No Exotic Cleaning Solutions •Military No...Explosion from Bullets/Shrapnel •On-Board Inert Gas Generating System (OBIGGS) Replaced Halon 1301 •Filters out Oxygen from Ambient Air to Create...Supply System •Supply System Must Be Perfectly Clean •Best Cleaning Solutions Freon CFC-113 and HCFC-141b •On-Board Oxygen Generating System Replaced

Performing process migration with allreduce operations

DOEpatents

Archer, Charles Jens; Peters, Amanda; Wallenfelt, Brian Paul

2010-12-14

Compute nodes perform allreduce operations that swap processes at nodes. A first allreduce operation generates a first result and uses a first process from a first compute node, a second process from a second compute node, and zeros from other compute nodes. The first compute node replaces the first process with the first result. A second allreduce operation generates a second result and uses the first result from the first compute node, the second process from the second compute node, and zeros from others. The second compute node replaces the second process with the second result, which is the first process. A third allreduce operation generates a third result and uses the first result from first compute node, the second result from the second compute node, and zeros from others. The first compute node replaces the first result with the third result, which is the second process.

Production of maternal-zygotic mutant zebrafish by germ-line replacement.

PubMed

Ciruna, Brian; Weidinger, Gilbert; Knaut, Holger; Thisse, Bernard; Thisse, Christine; Raz, Erez; Schier, Alexander F

2002-11-12

We report a generally applicable strategy for transferring zygotic lethal mutations through the zebrafish germ line. By using a morpholino oligonucleotide that blocks primordial germ cell (PGC) development, we generate embryos devoid of endogenous PGCs to serve as hosts for the transplantation of germ cells derived from homozygous mutant donors. Successful transfers are identified by the localization of specifically labeled donor PGCs to the region of the developing gonad in chimeric embryos. This strategy, which results in the complete replacement of the host germ line with donor PGCs, was validated by the generation of maternal and maternal-zygotic mutants for the miles apart locus. This germ-line replacement technique provides a powerful tool for studying the maternal effects of zygotic lethal mutations. Furthermore, the ability to generate large clutches of purely mutant embryos will greatly facilitate embryological, genetic, genomic, and biochemical studies.

Production of maternal-zygotic mutant zebrafish by germ-line replacement

PubMed Central

Ciruna, Brian; Weidinger, Gilbert; Knaut, Holger; Thisse, Bernard; Thisse, Christine; Raz, Erez; Schier, Alexander F.

2002-01-01

We report a generally applicable strategy for transferring zygotic lethal mutations through the zebrafish germ line. By using a morpholino oligonucleotide that blocks primordial germ cell (PGC) development, we generate embryos devoid of endogenous PGCs to serve as hosts for the transplantation of germ cells derived from homozygous mutant donors. Successful transfers are identified by the localization of specifically labeled donor PGCs to the region of the developing gonad in chimeric embryos. This strategy, which results in the complete replacement of the host germ line with donor PGCs, was validated by the generation of maternal and maternal-zygotic mutants for the miles apart locus. This germ-line replacement technique provides a powerful tool for studying the maternal effects of zygotic lethal mutations. Furthermore, the ability to generate large clutches of purely mutant embryos will greatly facilitate embryological, genetic, genomic, and biochemical studies. PMID:12397179

Transapical Implantation of a 2nd-Generation JenaValve Device in Patient with Extremely High Surgical Risk

PubMed Central

Mieres, Juan; Menéndez, Marcelo; Fernández-Pereira, Carlos; Rubio, Miguel; Rodríguez, Alfredo E.

2015-01-01

Transcatheter Aortic Valve Replacement (TAVR) is performed in patients who are poor surgical candidates. Many patients have inadequate femoral access, and alternative access sites have been used such as the transapical approach discussed in this paper. We present an elderly and fragile patient not suitable for surgery for unacceptable high risk, including poor ventricular function, previous myocardial infarction with percutaneous coronary intervention, pericardial effusion, and previous cardiac surgery with replacement of mechanical mitral valve. Transapical aortic valve replacement with a second-generation self-expanding JenaValve is performed. The JenaValve is a second-generation transapical TAVR valve consisting of a porcine root valve mounted on a low-profile nitinol stent. The valve is fully retrievable and repositionable. We discuss transapical access, implantation technique, and feasibility of valve implantation in this extremely high surgical risk patient. PMID:26346128

Transapical Implantation of a 2nd-Generation JenaValve Device in Patient with Extremely High Surgical Risk.

PubMed

Mieres, Juan; Menéndez, Marcelo; Fernández-Pereira, Carlos; Rubio, Miguel; Rodríguez, Alfredo E

2015-01-01

Transcatheter Aortic Valve Replacement (TAVR) is performed in patients who are poor surgical candidates. Many patients have inadequate femoral access, and alternative access sites have been used such as the transapical approach discussed in this paper. We present an elderly and fragile patient not suitable for surgery for unacceptable high risk, including poor ventricular function, previous myocardial infarction with percutaneous coronary intervention, pericardial effusion, and previous cardiac surgery with replacement of mechanical mitral valve. Transapical aortic valve replacement with a second-generation self-expanding JenaValve is performed. The JenaValve is a second-generation transapical TAVR valve consisting of a porcine root valve mounted on a low-profile nitinol stent. The valve is fully retrievable and repositionable. We discuss transapical access, implantation technique, and feasibility of valve implantation in this extremely high surgical risk patient.

Connecticut Biodiesel Power Generation Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grannis, Lee; York, Carla R.

Sabre will continue support of the emissions equipment and VARS issues to ensure all are resolved and the system is functioning as expected. The remote data collection to become more automated. Final project reports for data collection and system performance to be generated. Sabre continued to support the emissions equipment and VARS issues to ensure all are resolved and the system is functioning as expected. The remote data collection became more automated. Final project reports for data collection and system performance were generated and are part of this final report. Some Systems Sensors were replaced due to a lightning strike.more » Sample data charts are shown at the end of the report. During the project, Sabre Engineering provided support to the project team with regarding to troubleshooting technical issues and system integration with the local power utility company. The resulting lessons learned through Sabre’s participation in the project have been valuable to the integrity of the data collected as well as in providing BioPur Light & Power valuable insights into future operations and planning for possible expansion. The system monitoring and data collection system has been operating as designed and continues to provide relevant information to the system operators. The information routinely gathered automatically by the system also contributes to the REN and REC validations which are required to secure credit for these items. During the quarter, the remaining work on the operations and safety manual were completed and released for publication after screen shots were verified. The goal of this effort to provide an accurate set of precautions and procedures for the technology system that can be replicated to other similar system.« less

Implantable Systems for Continuous Liquorpheresis and CSF Replacement

PubMed Central

2017-01-01

Liquorpheresis (cerebrospinal fluid filtration) comprises a therapeutical approach that has been proposed to treat several neurological conditions where antibodies, inflammatory mediators, or abnormal peptides are the cause or play an important role in the pathogenesis of the disease. Continuous or intermittent cerebrospinal fluid (CSF) replacement may be an alternative approach not explored thus far. Here, we review previous experiences in the use of liquorpheresis in autoimmune and degenerative neurological diseases. Then we describe previous technical reports  and provide some new innovations in order to design bidirectional CSF shunting systems that can be complemented either with a deposit of artificial CSF or with a filter of CSF, allowing CSF replacement or liquorpheresis respectively. Both options would lead to mechanical dilution of the patient’s CSF. PMID:28413734

Continuous 28-day iododeoxyuridine infusion and hyperfractionated accelerated radiotherapy for malignant glioma: a phase I clinical study.

PubMed

Schulz, Craig A; Mehta, Minesh P; Badie, Benham; McGinn, Cornelius J; Robins, H Ian; Hayes, Lori; Chappell, Rick; Volkman, Jen; Binger, Kim; Arzoomanian, Rhoda; Simon, Kris; Alberti, Dona; Feierabend, Christine; Tutsch, Kendra D; Kunugi, Keith A; Wilding, George; Kinsella, Timothy J

2004-07-15

To investigate the maximal tolerated dose of a continuous 28-day iododeoxyuridine (IUdr) infusion combined with hyperfractionated accelerated radiotherapy (HART); to analyze the percentage of IUdr-thymidine replacement in peripheral granulocytes as a surrogate marker for IUdr incorporation into tumor cells; to measure the steady-state serum IUdr levels; and to assess the feasibility of continuous IUdr infusion and HART in the management of malignant glioma. Patients were required to have biopsy-proven malignant glioma. Patients received 100 (n = 4), 200 (n = 3), 300 (n = 3), 400 (n = 6), 500 (n = 4), 625 (n = 5), or 781 (n = 6) mg/m(2)/d of IUdr by continuous infusion for 28 days. HART was started 7 days after IUdr initiation. The total dose was 70 Gy (1.2 Gy b.i.d. for 25 days with a 10-Gy boost [2.0 Gy for 5 Saturdays]). Weekly assays were performed to determine the percentage of IUdr-DNA replacement in granulocytes and serum IUdr levels using standard high performance liquid chromatography methods. Standard Phase I toxicity methods were used. Between June 1994 and August 1999, 31 patients were enrolled. No patient had Grade 3 or worse HART toxicity. Grade 3 or greater IUdr toxicity predominantly included neutropenia (n = 3), thrombocytopenia (n = 3), and elevated liver function studies (n = 3). The maximal tolerated dose was 625 mg/m(2)/d. Thymidine replacement in the peripheral granulocytes peaked at 3 weeks and increased with the dose (maximal thymidine replacement 4.9%). The steady-state plasma IUdr level increased with the dose (maximum, 1.5 microM). In our study, continuous long-term IUdr i.v. infusion had a maximal tolerated dose of 625 mg/m(2)/d. Granulocyte incorporation data verified the concept that prolonged IUdr infusion results in IUdr-DNA replacement that corresponds to a high degree of cell labeling. IUdr steady-state plasma levels increased with increasing dose and attained levels needed for clinical radiosensitization. Continuous IUdr infusion and HART were both feasible and well tolerated.

Astronaut tool development: An orbital replaceable unit-portable handhold

NASA Technical Reports Server (NTRS)

Redmon, John W., Jr.

1989-01-01

A tool to be used during astronaut Extra-Vehicular Activity (EVA) replacement of spent or defective electrical/electronic component boxes is described. The generation of requirements and design philosophies are detailed, as well as specifics relating to mechanical development, interface verifications, testing, and astronaut feedback. Findings are presented in the form of: (1) a design which is universally applicable to spacecraft component replacement, and (2) guidelines that the designer of orbital replacement units might incorporate to enhance spacecraft on-orbit maintainability and EVA mission safety.

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. E. Lawson, R. Marsala, S. Ramakrishnan, X. Zhao, P. Sichta

In order to provide improved and expanded experimental capabilities, the existing Transrex power supplies at PPPL are to be upgraded and modernized. Each of the 39 power supplies consists of two six pulse silicon controlled rectifier sections forming a twelve pulse power supply. The first modification is to split each supply into two independent six pulse supplies by replacing the existing obsolete twelve pulse firing generator with two commercially available six pulse firing generators. The second change replaces the existing control link with a faster system, with greater capacity, which will allow for independent control of all 78 power supplymore » sections. The third change replaces the existing Computer Automated Measurement and Control (CAMAC) based fault detector with an Experimental Physics and Industrial Control System (EPICS) compatible unit, eliminating the obsolete CAMAC modules. Finally the remaining relay logic and interfaces to the "Hardwired Control System" will be replaces with a Programmable Logic Controller (PLC).« less

Wearable Fall Detector using Integrated Sensors and Energy Devices

PubMed Central

Jung, Sungmook; Hong, Seungki; Kim, Jaemin; Lee, Sangkyu; Hyeon, Taeghwan; Lee, Minbaek; Kim, Dae-Hyeong

2015-01-01

Wearable devices have attracted great attentions as next-generation electronic devices. For the comfortable, portable, and easy-to-use system platform in wearable electronics, a key requirement is to replace conventional bulky and rigid energy devices into thin and deformable ones accompanying the capability of long-term energy supply. Here, we demonstrate a wearable fall detection system composed of a wristband-type deformable triboelectric generator and lithium ion battery in conjunction with integrated sensors, controllers, and wireless units. A stretchable conductive nylon is used as electrodes of the triboelectric generator and the interconnection between battery cells. Ethoxylated polyethylenimine, coated on the surface of the conductive nylon electrode, tunes the work function of a triboelectric generator and maximizes its performance. The electrical energy harvested from the triboelectric generator through human body motions continuously recharges the stretchable battery and prolongs hours of its use. The integrated energy supply system runs the 3-axis accelerometer and related electronics that record human body motions and send the data wirelessly. Upon the unexpected fall occurring, a custom-made software discriminates the fall signal and an emergency alert is immediately sent to an external mobile device. This wearable fall detection system would provide new opportunities in the mobile electronics and wearable healthcare. PMID:26597423

Tehachapi Wind Energy Storage Project - Technology Performance Report #3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinsky, Naum; O'Neill, Lori

The TSP is located at SCE’s Monolith Substation in Tehachapi, California. The 8 MW, 4 hours (32 MWh) BESS is housed in a 6,300 square foot facility and 2 x 4 MW/4.5 MVA smart inverters are on a concrete pad adjacent to the BESS facility. The project will evaluate the capabilities of the BESS to improve grid performance and assist in the integration of large-scale intermittent generation, e.g., wind. Project performance was measured by 13 specific operational uses: providing voltage support and grid stabilization, decreasing transmission losses, diminishing congestion, increasing system reliability, deferring transmission investment, optimizing renewable-related transmission, providing systemmore » capacity and resources adequacy, integrating renewable energy (smoothing), shifting wind generation output, frequency regulation, spin/non-spin replacement reserves, ramp management, and energy price arbitrage. Most of the operations either shift other generation resources to meet peak load and other electricity system needs with stored electricity, or resolve grid stability and capacity concerns that result from the interconnection of intermittent generation. SCE also demonstrated the ability of lithium ion battery storage to provide nearly instantaneous maximum capacity for supply-side ramp rate control to minimize the need for fossil fuel-powered back-up generation. The project began in October, 2010 and will continue through December, 2016.« less

Instant Generation

ERIC Educational Resources Information Center

Loveland, Elaina

2017-01-01

Generation Z students (born between 1995-2010) have replaced millennials on college campuses. Generation Z students are entrepreneurial, desire practical skills with their education, and are concerned about the cost of college. This article presents what need to be known about this new generation of students.

Novel Synthetic Medea selfish genetic elements drive population replacement in Drosophila, and a theoretical exploration of Medea-dependent population suppression

PubMed Central

Akbari, Omar S.; Chen, Chun-Hong; Marshall, John M.; Huang, Haixia; Antoshechkin, Igor; Hay, Bruce A.

2013-01-01

Insects act as vectors for diseases of plants, animals and humans. Replacement of wild insect populations with genetically modified individuals unable to transmit disease provides a potentially self-perpetuating method of disease prevention. Population replacement requires a gene drive mechanism in order to spread linked genes mediating disease refractoriness through wild populations. We previously reported the creation of synthetic Medea selfish genetic elements able to drive population replacement in Drosophila. These elements use microRNA-mediated silencing of myd88, a maternally expressed gene required for embryonic dorso-ventral pattern formation, coupled with early zygotic expression of a rescuing transgene, to bring about gene drive. Medea elements that work through additional mechanisms are needed in order to be able to carry out cycles of population replacement and/or remove existing transgenes from the population, using second-generation elements that spread while driving first-generation elements out of the population. Here we report the synthesis and population genetic behavior of two new synthetic Medea elements that drive population replacement through manipulation of signaling pathways involved in cellular blastoderm formation or Notch signaling, demonstrating that in Drosophila Medea elements can be generated through manipulation of diverse signaling pathways. We also describe the mRNA and small RNA changes in ovaries and early embryos associated from Medea-bearing females. Finally, we use modeling to illustrate how Medea elements carrying genes that result in diapause-dependent female lethality could be used to bring about population suppression. PMID:23654248

The pharmacokinetics and extracorporeal removal of N-acetylcysteine during renal replacement therapies.

PubMed

Hernandez, Stephanie H; Howland, Maryann; Schiano, Thomas D; Hoffman, Robert S

2015-01-01

Acetaminophen-induced fulminant hepatic failure is associated with acute kidney injury, metabolic acidosis, and fluid and electrolyte imbalances, requiring treatment with renal replacement therapies. Although antidote, acetylcysteine, is potentially extracted by renal replacement therapies, pharmacokinetic data are lacking to guide potential dosing alterations. We aimed to determine the extracorporeal removal of acetylcysteine by various renal replacement therapies. Simultaneous urine, plasma and effluent specimens were serially collected to measure acetylcysteine concentrations in up to three stages: before, during and upon termination of renal replacement therapy. Alterations in pharmacokinetics were determined by applying standard pharmacokinetic equations. Over 2 years, 10 critically ill patients in fulminant hepatic failure requiring renal replacement therapy coincident with acetylcysteine were consecutively enrolled. All 10 patients required continuous venovenous hemofiltration (n = 10) and 2 of the 10 also required hemodialysis (n = 2). There was a significant alteration in the pharmacokinetics of acetylcysteine during hemodialysis; the area under the curve (AUC) decreased 41%, the mean extraction ratio was 51%, the mean hemodialytic clearance was 114.01 ml/kg/h, and a mean 166.75 mg/h was recovered in the effluent or 41% of the hourly dose. Alteration in the pharmacokinetics of acetylcysteine during continuous venovenous hemofiltration did not appear to be significant: the AUC decreased 13%, the mean clearance was 31.77 ml/kg/h and a mean 62.12 mg/h was recovered in the effluent or 14% of the hourly dose. There was no significant extraction of acetylcysteine from continuous venovenous hemofiltration. In contrast, there was significant extracorporeal removal of acetylcysteine during hemodialysis. A reasonable dose adjustment may be to double the IV infusion rate or possibly supplement with oral acetylcysteine during hemodialysis.

Oxygen enhanced switching to combustion of lower rank fuels

DOEpatents

Kobayashi, Hisashi; Bool, III, Lawrence E.; Wu, Kuang Tsai

2004-03-02

A furnace that combusts fuel, such as coal, of a given minimum energy content to obtain a stated minimum amount of energy per unit of time is enabled to combust fuel having a lower energy content, while still obtaining at least the stated minimum energy generation rate, by replacing a small amount of the combustion air fed to the furnace by oxygen. The replacement of oxygen for combustion air also provides reduction in the generation of NOx.

The influence of hypophosphatemia on outcomes of low- and high-intensity continuous renal replacement therapy in critically ill patients with acute kidney injury

PubMed Central

Kim, Soo Young; Kim, Ye Na; Shin, Ho Sik; Jung, Yeonsoon; Rim, Hark

2017-01-01

Background The purpose of this study was to assess the role of hypophosphatemia in major clinical outcomes of patients treated with low- or high-intensity continuous renal replacement therapy (CRRT). Methods We performed a retrospective analysis of data collected from 492 patients. We divided patients into two CRRT groups based on treatment intensity (greater than or equal to or less than 40 mL/kg/hour of effluent generation) and measured serum phosphate level daily during CRRT. Results We obtained a total of 1,440 phosphate measurements on days 0, 1, and 2 and identified 39 patients (7.9%), 74 patients (15.0%), and 114 patients (23.1%) with hypophosphatemia on each of these respective days. In patients treated with low-intensity CRRT, there were 23 episodes of hypophosphatemia/1,000 patient days, compared with 83 episodes/1,000 patient days in patients who received high-intensity CRRT (P < 0.01). Multiple Cox proportional hazards analysis showed that Acute Physiology and Chronic Health Evaluation (APACHE) III score, utilization of vasoactive drugs, and arterial pH on the second day of CRRT were significant predictors of mortality, while serum phosphate level was not a significant contributor to mortality. Conclusion APACHE score, use of vasoactive drugs, and arterial pH on the second CRRT day were identified as significant predictors of mortality. Hypophosphatemia might not be a major risk factor of increased mortality in patients treated with CRRT. PMID:28904875

The relationship between hypophosphataemia and outcomes during low-intensity and high-intensity continuous renal replacement therapy.

PubMed

Bellomo, Rinaldo; Cass, Alan; Cole, Louise; Finfer, Simon; Gallagher, Martin; Kim, Inbyung; Lee, Joanne; Lo, Serigne; McArthur, Colin; McGuinness, Shay; McGuiness, Shay; Norton, Robyn; Myburgh, John; Scheinkestel, Carlos

2014-03-01

To identify risk factors for development of hypophosphataemia in patients treated with two different intensities of continuous renal replacement therapy (CRRT) and to assess the independent association of hypophosphataemia with major clinical outcomes. We performed secondary analysis of data collected from 1441 patients during a large, multicentre randomised controlled trial of CRRT intensity. We allocated patients to two different intensities of CRRT (25mL/kg/hour vs 40 mL/kg/hour of effluent generation) and obtained daily measurement of serum phosphate levels. We obtained 14 115 phosphate measurements and identified 462 patients (32.1%) with hypophosphataemia, with peak incidence on Day 2 and Day 3. With lower intensity CRRT, there were 58 episodes of hypophosphataemia/1000 patient days, compared with 112 episodes/1000 patient days with higher intensity CRRT (P < 0.001). On multivariable logistic regression analysis, higher intensity CRRT, female sex, higher Acute Physiology and Chronic Health Evaluation score and hypokalaemia were independently associated with an increased odds ratio (OR) for hypophosphataemia. On multivariable models, hypophosphataemia was associated with better clinical outcomes, but when analysis was confined to patients alive at 96 hours, hypophosphataemia was not independently associated with clinical outcomes. Hypophosphataemia is common during CRRT and its incidence increases with greater CRRT intensity. Hypophosphataemia is not a robust independent predictor of mortality. Its greater incidence in the higher intensity CRRT arm of the Randomised Evaluation of Normal vs Augmented Level trial does not explain the lack of improved outcomes with such treatment.

An evolutionary view on tooth development and replacement in wild Atlantic salmon (Salmo salar L.).

PubMed

Huysseune, A; Witten, P E

2008-01-01

To gain an insight into the evolution of tooth replacement mechanisms, we studied the development of first-generation and replacement teeth on the dentary of wild Atlantic salmon (Salmo salar L.), a protacanthopterygian teleost, using serially sectioned heads of early posthatching stages as well as adults. First-generation teeth develop within the oral epithelium. The anlage of the replacement tooth is first seen as a placode-like thickening of the outer dental epithelium of the predecessor, at its lingual and caudal side. Ongoing development of the replacement tooth germ is characterized by the elaboration of a population of epithelial cells, termed here the middle dental epithelium, apposed to the inner dental epithelium on the lingual side of the tooth germ. Before the formation of the new successor, a single-layered outer dental epithelium segregates from the middle dental epithelium. The dental organs of the predecessor and the successor remain broadly interconnected. The absence of a discrete successional dental lamina in salmon stands in sharp contrast to what is observed in other teleosts, even those that share with salmon the extraosseous formation of replacement teeth. The mode of tooth replacement in Atlantic salmon displays several characters similar to those observed in the shark Squalus acanthias. To interpret similarities in tooth replacement between Atlantic salmon and chondrichthyans as a case of convergence, or to see them as a result of a heterochronic shift, requires knowledge on the replacement process in more basal actinopterygian lineages. The possibility that the middle dental epithelium functionally substitutes for a successional lamina, and could be a source of stem cells, whose descendants subsequently contribute to the placode of the new replacement tooth, needs to be explored.

76 FR 6653 - Public Housing Capital Fund Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-07

...; heating system replacements; wall insulation; site-based generation; advanced energy savings technologies...; wall insulation; site-based generation; advanced energy savings technologies, including renewable...

A Compact Torus Fusion Reactor Utilizing a Continuously Generated Strings of CT's. The CT String Reactor, CTSR.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartman, C W; Reisman, D B; McLean, H S

2007-05-30

A fusion reactor is described in which a moving string of mutually repelling compact toruses (alternating helicity, unidirectional Btheta) is generated by repetitive injection using a magnetized coaxial gun driven by continuous gun current with alternating poloidal field. An injected CT relaxes to a minimum magnetic energy equilibrium, moves into a compression cone, and enters a conducting cylinder where the plasma is heated to fusion-producing temperature. The CT then passes into a blanketed region where fusion energy is produced and, on emergence from the fusion region, the CT undergoes controlled expansion in an exit cone where an alternating poloidal fieldmore » opens the flux surfaces to directly recover the CT magnetic energy as current which is returned to the formation gun. The CT String Reactor (CTSTR) reactor satisfies all the necessary MHD stability requirements and is based on extrapolation of experimentally achieved formation, stability, and plasma confinement. It is supported by extensive 2D, MHD calculations. CTSTR employs minimal external fields supplied by normal conductors, and can produce high fusion power density with uniform wall loading. The geometric simplicity of CTSTR acts to minimize initial and maintenance costs, including periodic replacement of the reactor first wall.« less

Hot-Fire Testing of 5N and 22N HPGP Thrusters

NASA Technical Reports Server (NTRS)

Burnside, Christopher G.; Pedersen, Kevin W.; Pierce, Charles W.

2015-01-01

This hot-fire test continues NASA investigation of green propellant technologies for future missions. To show the potential for green propellants to replace some hydrazine systems in future spacecraft, NASA Marshall Space Flight Center (MSFC) is continuing to embark on hot-fire test campaigns with various green propellant blends.NASA completed hot-fire testing of 5N and 22N HPGP thrusters at the Marshall Space Flight Center’s Component Development Area altitude test stand in April 2015. Both thrusters are ground test articles and not flight ready units, but are representative of potential flight hardware with a known path towards flight application. The purpose of the 5N testing was to perform facility check-outs and generate a small set of data for comparison to ECAPS and Orbital ATK data sets. The 5N thruster performed as expected with thrust and propellant flow-rate data generated that are similar to previous testing at Orbital ATK. Immediately following the 5N testing, and using the same facility, the 22N testing was conducted on the same test stand with the purpose of demonstrating the 22N performance. The results of 22N testing indicate it performed as expected.The results of the hot-fire testing are presented in this paper and presentation.

7 CFR 623.12 - Payments to landowners by NRCS.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) NATURAL RESOURCES CONSERVATION SERVICE... payments may be authorized for the replacement or restoration of practices for which cost share assistance has been previously allowed under the EWRP, but only if: (1) Replacement or restoration of the...

Language continuity despite population replacement in Remote Oceania.

PubMed

Posth, Cosimo; Nägele, Kathrin; Colleran, Heidi; Valentin, Frédérique; Bedford, Stuart; Kami, Kaitip W; Shing, Richard; Buckley, Hallie; Kinaston, Rebecca; Walworth, Mary; Clark, Geoffrey R; Reepmeyer, Christian; Flexner, James; Maric, Tamara; Moser, Johannes; Gresky, Julia; Kiko, Lawrence; Robson, Kathryn J; Auckland, Kathryn; Oppenheimer, Stephen J; Hill, Adrian V S; Mentzer, Alexander J; Zech, Jana; Petchey, Fiona; Roberts, Patrick; Jeong, Choongwon; Gray, Russell D; Krause, Johannes; Powell, Adam

2018-04-01

Recent genomic analyses show that the earliest peoples reaching Remote Oceania-associated with Austronesian-speaking Lapita culture-were almost completely East Asian, without detectable Papuan ancestry. However, Papuan-related genetic ancestry is found across present-day Pacific populations, indicating that peoples from Near Oceania have played a significant, but largely unknown, ancestral role. Here, new genome-wide data from 19 ancient South Pacific individuals provide direct evidence of a so-far undescribed Papuan expansion into Remote Oceania starting ~2,500 yr BP, far earlier than previously estimated and supporting a model from historical linguistics. New genome-wide data from 27 contemporary ni-Vanuatu demonstrate a subsequent and almost complete replacement of Lapita-Austronesian by Near Oceanian ancestry. Despite this massive demographic change, incoming Papuan languages did not replace Austronesian languages. Population replacement with language continuity is extremely rare-if not unprecedented-in human history. Our analyses show that rather than one large-scale event, the process was incremental and complex, with repeated migrations and sex-biased admixture with peoples from the Bismarck Archipelago.

Optimum random and age replacement policies for customer-demand multi-state system reliability under imperfect maintenance

NASA Astrophysics Data System (ADS)

Chen, Yen-Luan; Chang, Chin-Chih; Sheu, Dwan-Fang

2016-04-01

This paper proposes the generalised random and age replacement policies for a multi-state system composed of multi-state elements. The degradation of the multi-state element is assumed to follow the non-homogeneous continuous time Markov process which is a continuous time and discrete state process. A recursive approach is presented to efficiently compute the time-dependent state probability distribution of the multi-state element. The state and performance distribution of the entire multi-state system is evaluated via the combination of the stochastic process and the Lz-transform method. The concept of customer-centred reliability measure is developed based on the system performance and the customer demand. We develop the random and age replacement policies for an aging multi-state system subject to imperfect maintenance in a failure (or unacceptable) state. For each policy, the optimum replacement schedule which minimises the mean cost rate is derived analytically and discussed numerically.

GUIDES TO POLLUTION PREVENTION: THE AUTO REPAIR INDUSTRY

EPA Science Inventory

Automotive maintenance and repair shops generate a variety of waste streams during activities such as replacing fluids (e.g., motor oil, radiator coolant, transmission fluid, brake fluid), replacing non-repairable parts (e.g., brake shoes/pads, shocks, batteries, belts, mufflers,...

Canine total hip replacement using a cementless threaded cup and stem: a review of 55 cases.

PubMed

Denny, H R; Linnell, M; Maddox, T W; Comerford, E J

2018-06-01

To determine the long-term results and complications associated with the Helica ® cementless hip endoprosthesis system. Retrospective study of 55 consecutive Helica total hip replacements performed between January 2010 and February 2015. A total of 55 total hip replacements were performed in 50 dogs; 45 dogs had unilateral hip replacements, and five had staged bilateral replacements. A total of 23 first-generation short femoral stems were implanted in 22 dogs, of which nine cases (39%) experienced complications and 19 (86%) recovered satisfactorily when revisions were included; 31 second-generation femoral stems were implanted in 28 dogs, of which 10 cases (32%) experienced complications, and 26 (93%) made satisfactory recoveries, including revisions. In 36 dogs for which data were available, postoperative Liverpool Osteoarthritis in Dogs scores were significantly reduced compared to preoperative scores. Complications occurred in a total of 19 cases (34·5%; 95% confidence interval: 22 to 47·1%); the most common was aseptic loosening of the femoral stem [11 cases (20%; 95% confidence interval: 9·4 to 30·6%)]. Following multivariable analysis, no risk factors were identified for overall complications, but there was a significant association of implant type (first-generation short stem) with loosening (odds ratio 4·9, 95% confidence interval: 1·1 to 22·1, P=0·034). This study found the Helica hip endoprosthesis system to be effective in the management of hip dysplasia and osteoarthritis in dogs. Aseptic loosening of the femoral stem remains the most common complication but appears to have been significantly reduced with the introduction of the second-generation stem. © 2018 British Small Animal Veterinary Association.

Dose determinants in continuous renal replacement therapy.

PubMed

Clark, William R; Turk, Joseph E; Kraus, Michael A; Gao, Dayong

2003-09-01

Increasing attention is being paid to quantifying the dose of dialysis prescribed and delivered to critically ill patients with acute renal failure (ARF). Recent trials in both the intermittent hemodialysis (IHD) and continuous renal replacement therapy (CRRT) realms have suggested that a direct relationship between dose and survival exists for both of these therapies. The purpose of this review, first, is to analyze critically the above-mentioned dose/outcome studies in acute dialysis. Subsequently, the factors influencing dose prescription and delivery are discussed, with the focus on continuous venovenous hemofiltration (CVVH). Specifically, differences between postdilution and predilution CVVH will be highlighted, and the importance of blood flow rate in dose delivery for these therapies will be discussed.

46 CFR 54.10-3 - Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103). 54.10-3 Section 54.10-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Inspection, Reports, and Stamping § 54.10-3 Marine inspectors (replaces UG-90 and UG-91, and...

46 CFR 54.10-3 - Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103). 54.10-3 Section 54.10-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Inspection, Reports, and Stamping § 54.10-3 Marine inspectors (replaces UG-90 and UG-91, and...

46 CFR 54.10-3 - Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103). 54.10-3 Section 54.10-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Inspection, Reports, and Stamping § 54.10-3 Marine inspectors (replaces UG-90 and UG-91, and...

46 CFR 54.10-3 - Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103). 54.10-3 Section 54.10-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Inspection, Reports, and Stamping § 54.10-3 Marine inspectors (replaces UG-90 and UG-91, and...

46 CFR 54.10-3 - Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Marine inspectors (replaces UG-90 and UG-91, and modifies UG-92 through UG-103). 54.10-3 Section 54.10-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Inspection, Reports, and Stamping § 54.10-3 Marine inspectors (replaces UG-90 and UG-91, and...

ARIES: NASA Langley's Airborne Research Facility

NASA Technical Reports Server (NTRS)

Wusk, Michael S.

2002-01-01

In 1994, the NASA Langley Research Center (LaRC) acquired a B-757-200 aircraft to replace the aging B-737 Transport Systems Research Vehicle (TSRV). The TSRV was a modified B-737-100, which served as a trailblazer in the development of glass cockpit technologies and other innovative aeronautical concepts. The mission for the B-757 is to continue the three-decade tradition of civil transport technology research begun by the TSRV. Since its arrival at Langley, this standard 757 aircraft has undergone extensive modifications to transform it into an aeronautical research "flying laboratory". With this transformation, the aircraft, which has been designated Airborne Research Integrated Experiments System (ARIES), has become a unique national asset which will continue to benefit the U.S. aviation industry and commercial airline customers for many generations to come. This paper will discuss the evolution of the modifications, detail the current capabilities of the research systems, and provide an overview of the research contributions already achieved.

A method for modeling finite-core vortices in wake-flow calculations

NASA Technical Reports Server (NTRS)

Stremel, P. M.

1984-01-01

A numerical method for computing nonplanar vortex wakes represented by finite-core vortices is presented. The approach solves for the velocity on an Eulerian grid, using standard finite-difference techniques; the vortex wake is tracked by Lagrangian methods. In this method, the distribution of continuous vorticity in the wake is replaced by a group of discrete vortices. An axially symmetric distribution of vorticity about the center of each discrete vortex is used to represent the finite-core model. Two distributions of vorticity, or core models, are investigated: a finite distribution of vorticity represented by a third-order polynomial, and a continuous distribution of vorticity throughout the wake. The method provides for a vortex-core model that is insensitive to the mesh spacing. Results for a simplified case are presented. Computed results for the roll-up of a vortex wake generated by wings with different spanwise load distributions are presented; contour plots of the flow-field velocities are included; and comparisons are made of the computed flow-field velocities with experimentally measured velocities.

The need for a single cleaning standard for OEM and OSP fiber optic connections

NASA Astrophysics Data System (ADS)

Forrest, Edward J., Jr.; Blair, Paul

2009-01-01

Development of fiber optic communications networks has continued in virtually all geographies of the world. Some calculate that expansion in the USA alone will continue to 2025. After that time there will maintenance, upgrade, and replacement. While some nations are more advanced than others and some enterprises more sophisticated than others, the undeniable reality is that previous networks will, in some fashion or another, include fiber optics. The future need is for speed and reliable bandwidth: lots of it. Decisions will be made based on new concepts that will enable far more data at far faster rates than once considered feasible or necessary. As the consumer enters the market with newly engineered home entertainment systems, additional burdens will be placed on both OEM and OSP. These are not negative challenges, but rather indicators of a new generation of consumers with awareness and demand far more advanced any may have imagined just a few years ago.

STS-84 oxygen generator for Mir on display at SPACEHAB

NASA Technical Reports Server (NTRS)

1997-01-01

An oxygen generator destined to replace a malfunctioning unit on the Russian Mir Space Station is the object of much curiosity during preflight preparations in the SPACEHAB Payload Processing Facility. A SPACEHAB Double Module on the Space Shuttle Atlantis will carry the oxygen generator to Mir during STS-84, the sixth Shuttle-Mir docking. The nearly 300-pound generator, manufactured by RSC Energia in Russia, will replace one of two Mir units that have been malfunctioning recently. The generator functions by electrolysis, which separates water into its oxygen and hydrogen components. The hydrogen is vented and the oxygen is used for breathing by the Mir crew. The generator is 4.2 feet in length and 1.4 feet in diameter. STS-84, which is planned to include a Mir crew exchange of astronaut C. Michael Foale for Jerry M. Linenger, is targeted for a May 15 liftoff.

Local infiltration analgesia versus continuous interscalene brachial plexus block for shoulder replacement pain: a randomized clinical trial.

PubMed

Bjørnholdt, Karen T; Jensen, Jan M; Bendtsen, Thomas F; Søballe, Kjeld; Nikolajsen, Lone

2015-12-01

Shoulder replacement involves significant post-operative pain, which is often managed by continuous interscalene brachial plexus block. Catheter displacement and complications limit the beneficial effect of the block. Local infiltration analgesia (LIA) has provided good results in knee replacement. We aimed to assess the effectiveness of LIA for pain after shoulder replacement. Patients scheduled for primary shoulder replacement under general anaesthesia were randomized to receive either local infiltration analgesia (LIA) (150 ml ropivacaine 0.2 % with epinephrine intra-operatively) or interscalene brachial plexus catheter (ISC) (ropivacaine 0.75 %, 7 ml bolus followed by 48-h 5 ml/h infusion). The primary outcome was opioid consumption during the first 24 post-operative hours. Secondary outcomes were pain ratings, supplementary analgesics, and side effects for 3 days, and complications until 3 months after surgery. Data were analysed for 61 patients (LIA 30, ISC 31). Twenty-four-hour opioid consumption was higher in the LIA group compared with the ISC group: median (IQR) 95 mg (70-150 mg) versus 40 mg (8-76 mg) (P = 0.0001). No significant difference in opioid consumption was found between groups during the following 3 days. The LIA group had higher pain scores at 0, 2, 4, and 8 h. Two patients in the ISC group had long-lasting complications. The LIA technique cannot be recommended for shoulder replacement unless substantially modified. Occurrence of inadequate analgesia and complications following interscalene brachial plexus block prompt further studies into pain management after shoulder replacement.

24 CFR 960.609 - Prohibition against replacement of PHA employees.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Prohibition against replacement of PHA employees. 960.609 Section 960.609 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR PUBLIC AND INDIAN HOUSING...

Replacing fallow with continuous cropping reduces crop water productivity of semiarid wheat

USDA-ARS?s Scientific Manuscript database

Water supply frequently limits crop yield in semiarid cropping systems; water deficits can restrict yields in drought-affected subhumid regions. In semiarid wheat (Triticum aestivumL.)-based cropping systems, replacing an uncropped fallow period with a crop can increase precipitation use efficiency ...

46 CFR 56.95-1 - General (replaces 136).

Code of Federal Regulations, 2013 CFR

2013-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Inspection § 56.95-1 General (replaces 136). (a) The provisions in this subpart shall apply to... engineering design, and with the material, fabrication, assembly and test requirements of ASME B31.1, as...

46 CFR 56.95-1 - General (replaces 136).

Code of Federal Regulations, 2010 CFR

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Inspection § 56.95-1 General (replaces 136). (a) The provisions in this subpart shall apply to... engineering design, and with the material, fabrication, assembly and test requirements of ASME B31.1, as...

46 CFR 56.95-1 - General (replaces 136).

Code of Federal Regulations, 2014 CFR

2014-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Inspection § 56.95-1 General (replaces 136). (a) The provisions in this subpart shall apply to... engineering design, and with the material, fabrication, assembly and test requirements of ASME B31.1, as...

46 CFR 56.95-1 - General (replaces 136).

Code of Federal Regulations, 2012 CFR

2012-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Inspection § 56.95-1 General (replaces 136). (a) The provisions in this subpart shall apply to... engineering design, and with the material, fabrication, assembly and test requirements of ASME B31.1, as...

46 CFR 56.95-1 - General (replaces 136).

Code of Federal Regulations, 2011 CFR

2011-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Inspection § 56.95-1 General (replaces 136). (a) The provisions in this subpart shall apply to... engineering design, and with the material, fabrication, assembly and test requirements of ASME B31.1, as...

Investigation into the High Voltage Shutdown of the Oxygen Generator System in the International Space Station

NASA Technical Reports Server (NTRS)

Carpenter, Joyce E.; Gentry, Gregory J.; Diderich, Greg S.; Roy, Robert J.; Golden, John L.; VanKeuren, Steve; Steele, John W.; Rector, Tony J.; Varsik, Jerome D.; Montefusco, Daniel J.;

Development of pea protein-based bioplastics with antimicrobial properties.

PubMed

Perez-Puyana, Víctor; Felix, Manuel; Romero, Alberto; Guerrero, Antonio

2017-06-01

In the present work, bioplastics from renewable polymers were studied in order to reduce the huge generation of plastic wastes, causing an environmental problem that continues owing to the increasing demand for plastic products. Bioplastics with much better antimicrobial properties, in particular against Gram-positive bacteria, were obtained with the addition of nisin to the initial protein/plasticizer mixture. However, the addition of nisin produces more rigid but less deformable bioplastics (higher Young's modulus but lower strain at break). The results obtained are useful to demonstrate the antimicrobial properties of pea protein-based bioplastics by adding nisin and make them suitable as potential candidates to replace conventional plastics in food packaging. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

A logic-based method for integer programming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooker, J.; Natraj, N.R.

1994-12-31

We propose a logic-based approach to integer programming that replaces traditional branch-and-cut techniques with logical analogs. Integer variables are regarded as atomic propositions. The constraints give rise to logical formulas that are analogous to separating cuts. No continuous relaxation is used. Rather, the cuts are selected so that they can be easily solved as a discrete relaxation. (In fact, defining a relaxation and generating cuts are best seen as the same problem.) We experiment with relaxations that have a k-tree structure and can be solved by nonserial dynamic programming. We also present logic-based analogs of facet-defining cuts, Chv{acute a}tal rank,more » etc. We conclude with some preliminary computational results.« less

Experimental replacement of calcium carbonates by fluorite: high volume changes and porosity generation

NASA Astrophysics Data System (ADS)

Trindade Pedrosa, Elisabete; Putnis, Andrew

2015-04-01

Pseudomorphic mineral replacement reactions are a common phenomena in nature, and often described as interface-coupled dissolution-reprecipitation processes. The generation of porosity is a key factor for its progression since it creates the pathway for fluid infiltration towards an ongoing reaction front. The generation of porosity depends on two key factors: the molar volume differences between parent and product phase, and the relative solubilities of the parent and product in the fluid at the mineral-fluid interface (Pollok et al., 2011). Jamtveit et al., (2009) demonstrated that the permeability of the parent rock may also be enhanced by the development of fractures as a response to stresses generated by local volume changes at the reaction interface, which in turn increases the reaction rate. The replacement of calcite (CaCO3) by fluorite (CaF2) involves a molar volume decrease of 33.5 %. If indeed high volume changes generate high local stresses, a fragmentation process is expected to be driven by this replacement reaction. To test this hypothesis, a number of hydrothermal experiments were performed. Small cubes of calcite rock (Carrara marble), and single crystals of calcite were used as parent materials. Two fluoride solutions (ammonium fluoride and sodium fluoride) were used as reactants. Samples were reacted at temperatures up to 200°C for various times and quenched to room temperature. After drying, samples were mounted in epoxy holders, cross sections through the centre of the samples were cut and polished, and analysed using scanning electron microscopy (SEM), X-ray diffraction (XRD), and electron microprobe analysis (EMP). The replacement end product of all experiments was confirmed to be fluorite. In every case the external shape of the samples was perfectly maintained. No reaction induced fracturing was visible in any of the samples (rock or single crystals) although the texture of the replaced material was quite complex, often with a 'V' shaped reaction front. The main difference between single crystals and rock was that in the former, grain boundaries were rapid transport pathways for fluid infiltration resulting in the precipitation of fluorite within the sample at locations further from the main reaction front. The porosity formed was very high and complex, its texture depending on the shape and orientation of the replaced material. Very large hollow spaces with diameter >30 μm formed in several samples. In this system the large volume decrease is accommodated by a high porosity rather than fracturing. Jamtveit B., Putnis C.V. & Malthe-Sørenssen A. (2009). Reaction induced fracturing during replacement processes. Contrib. Min. Pet., 157 127-133 Pollok K., Putnis C.V. & Putnis A. (2011) Mineral replacement reactions in solid solution-aqueous solution systems: Volume changes, reaction paths and end points using the example of model salt systems. Am. J. Sci., 311, 211-236

The cost analysis of cemented versus cementless total hip replacement operations on the NHS.

PubMed

Kallala, R; Anderson, P; Morris, S; Haddad, F S

2013-07-01

In a time of limited resources, the debate continues over which types of hip prosthesis are clinically superior and more cost-effective. Orthopaedic surgeons increasingly need robust economic evidence to understand the full value of the operation, and to aid decision making on the 'package' of procedures that are available and to justify their practice beyond traditional clinical preference. In this paper we explore the current economic debate about the merits of cemented and cementless total hip replacement, an issue that continues to divide the orthopaedic community.

Design colloidal particle morphology and self-assembly for coating applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Shan; Van Dyk, Antony; Maurice, Alvin

The progressive replacement of organic solvent-based coatings by waterborne latex polymer coatings has substantially renovated the coating industry, and generated huge environmental and health benefits. Today, on top of the continuing demand for higher performance and lower costs, the coating industry faces tighter regulation and higher sustainability standards. In addition, the new waterborne coatings have created unique opportunities and challenges in terms of fundamental understanding and research development. To address these challenges, polymer latex binders with diverse particle morphologies have been developed to improve coating performance. Furthermore, colloidal self-assembly has been utilized to help manufacturers make better paint with lessmore » cost. In this report, we review the recent progress in both fundamental study and industrial application in the context of developing new generation architectural coating materials. We introduce the basic concepts in coating materials and showcase several key technologies that have been implemented to improve coating performance. As a result, these technologies also represent the most important considerations in architectural coating design.« less

Watering Down Barriers to Using Hydropower through Fisheries Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ham, Ken

Much of our work on clean energy is targeted at improving performance of hydropower, the largest source of renewable energy in the Pacific Northwest and the nation. PNNL experts in hydropower—from computer scientists to biologists and engineers—are helping to optimize the efficiency and environmental performance of hydroelectric plants. The Columbia River is the nation’s most important hydropower resource, producing 40 percent of the nation’s hydroelectric generation and up to 70 percent of the region’s power. At PNNL, Fisheries Biologist Ken Ham and others are working with stakeholders in the Pacific Northwest, the Army Corps of Engineers and DOE to ensuremore » that this resource continues to provide its many benefits while setting a new standard for environmental sustainability. As aging turbines are replaced in existing hydropower dams, computational modeling and state-of-the-art fisheries research combine to aid the design of a next-generation hydro turbine that meets or exceeds current biological performance standards and produces more power.« less

Design colloidal particle morphology and self-assembly for coating applications

DOE PAGES

Jiang, Shan; Van Dyk, Antony; Maurice, Alvin; ...

2017-05-04

The progressive replacement of organic solvent-based coatings by waterborne latex polymer coatings has substantially renovated the coating industry, and generated huge environmental and health benefits. Today, on top of the continuing demand for higher performance and lower costs, the coating industry faces tighter regulation and higher sustainability standards. In addition, the new waterborne coatings have created unique opportunities and challenges in terms of fundamental understanding and research development. To address these challenges, polymer latex binders with diverse particle morphologies have been developed to improve coating performance. Furthermore, colloidal self-assembly has been utilized to help manufacturers make better paint with lessmore » cost. In this report, we review the recent progress in both fundamental study and industrial application in the context of developing new generation architectural coating materials. We introduce the basic concepts in coating materials and showcase several key technologies that have been implemented to improve coating performance. As a result, these technologies also represent the most important considerations in architectural coating design.« less

PIV Analysis Comparing Aerodynamic Downforce Devices on Race Car in Water Tunnel

NASA Astrophysics Data System (ADS)

Hellman, Sam; Tkacik, Peter; Uddin, Mesbah; Kelly, Scott

2010-11-01

There have been claims that the rear wing on the NASCAR Car of Tomorrow (COT) race car causes lift in the condition where the car spins during a crash and is traveling backwards down the track at a high rate of speed. When enough lift is generated, the race car can lose control and even fly off of the track surface completely. To address this concern, a new rear spoiler was designed by NASCAR to replace the wing and prevent this dangerous condition. Flow characteristics of both the rear wing and the new spoiler are qualitatively analyzed using particle image velocimetry (PIV). The experiment is done in a continuous flow water tunnel using a simplified 10% scale model COT. Flow structures are identified and compared for both the wing and spoiler. The same conditions are also reviewed when the car is traveling backwards as it might during a crash. The cause of the lift generated by the rear wing when in reverse is shown.

An adaptive replacement algorithm for paged-memory computer systems.

NASA Technical Reports Server (NTRS)

Thorington, J. M., Jr.; Irwin, J. D.

1972-01-01

A general class of adaptive replacement schemes for use in paged memories is developed. One such algorithm, called SIM, is simulated using a probability model that generates memory traces, and the results of the simulation of this adaptive scheme are compared with those obtained using the best nonlookahead algorithms. A technique for implementing this type of adaptive replacement algorithm with state of the art digital hardware is also presented.

Gene replacements and insertions in rice by intron targeting using CRISPR-Cas9.

PubMed

Li, Jun; Meng, Xiangbing; Zong, Yuan; Chen, Kunling; Zhang, Huawei; Liu, Jinxing; Li, Jiayang; Gao, Caixia

2016-09-12

Sequence-specific nucleases have been exploited to create targeted gene knockouts in various plants(1), but replacing a fragment and even obtaining gene insertions at specific loci in plant genomes remain a serious challenge. Here, we report efficient intron-mediated site-specific gene replacement and insertion approaches that generate mutations using the non-homologous end joining (NHEJ) pathway using the clustered regularly interspaced short palindromic repeats (CRISPR)-CRISPR-associated protein 9 (Cas9) system. Using a pair of single guide RNAs (sgRNAs) targeting adjacent introns and a donor DNA template including the same pair of sgRNA sites, we achieved gene replacements in the rice endogenous gene 5-enolpyruvylshikimate-3-phosphate synthase (EPSPS) at a frequency of 2.0%. We also obtained targeted gene insertions at a frequency of 2.2% using a sgRNA targeting one intron and a donor DNA template including the same sgRNA site. Rice plants harbouring the OsEPSPS gene with the intended substitutions were glyphosate-resistant. Furthermore, the site-specific gene replacements and insertions were faithfully transmitted to the next generation. These newly developed approaches can be generally used to replace targeted gene fragments and to insert exogenous DNA sequences into specific genomic sites in rice and other plants.

KSC-97pc655

NASA Image and Video Library

1997-04-16

An oxygen generator destined to replace a malfunctioning unit on the Russian Mir Space Station is the object of much curiosity during preflight preparations in the SPACEHAB Payload Processing Facility. A SPACEHAB Double Module on the Space Shuttle Atlantis will carry the oxygen generator to Mir during STS-84, the sixth Shuttle-Mir docking. The nearly 300-pound generator, manufactured by RSC Energia in Russia, will replace one of two Mir units that have been malfunctioning recently. The generator functions by electrolysis, which separates water into its oxygen and hydrogen components. The hydrogen is vented and the oxygen is used for breathing by the Mir crew. The generator is 4.2 feet in length and 1.4 feet in diameter. STS-84, which is planned to include a Mir crew exchange of astronaut C. Michael Foale for Jerry M. Linenger, is targeted for a May 15 liftoff

OGS Maintenance

NASA Image and Video Library

2010-07-21

ISS024-E-009246 (21 July 2010) --- NASA astronaut Tracy Caldwell Dyson, Expedition 24 flight engineer, is pictured during troubleshooting operations of the Oxygen Generator System (OGS) hardware and replacement of an H2 (hydrogen) Dome Orbit Replaceable Unit (ORU) in the Destiny laboratory of the International Space Station.

Next Generation Spacecraft, Crew Exploration Vehicle

NASA Technical Reports Server (NTRS)

2004-01-01

This special bibliography includes research on reusable launch vehicles, aerospace planes, shuttle replacement, crew/cargo transfer vehicle, related X-craft, orbital space plane, and next generation launch technology.

21 CFR 870.3710 - Pacemaker repair or replacement material.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Pacemaker repair or replacement material. 870.3710 Section 870.3710 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3710 Pacemaker...

Program for Assisting the Replacement of Industrial Solvents PARIS III User’s Guide

EPA Science Inventory

PARIS III is a third generation Windows-based computer software to assist the design of less harmful solvent replacements by estimating values of the solvent properties that characterize the static, dynamic, performance, and environmental behavior of the original solvent mixture ...

X-ray structure determination using low-resolution electron microscopy maps for molecular replacement

DOE PAGES

Jackson, Ryan N.; McCoy, Airlie J.; Terwilliger, Thomas C.; ...

2015-07-30

Structures of multi-subunit macromolecular machines are primarily determined by either electron microscopy (EM) or X-ray crystallography. In many cases, a structure for a complex can be obtained at low resolution (at a coarse level of detail) with EM and at higher resolution (with finer detail) by X-ray crystallography. The integration of these two structural techniques is becoming increasingly important for generating atomic models of macromolecular complexes. A low-resolution EM image can be a powerful tool for obtaining the "phase" information that is missing from an X-ray crystallography experiment, however integration of EM and X-ray diffraction data has been technically challenging.more » Here we show a step-by-step protocol that explains how low-resolution EM maps can be placed in the crystallographic unit cell by molecular replacement, and how initial phases computed from the placed EM density are extended to high resolution by averaging maps over non-crystallographic symmetry. As the resolution gap between EM and Xray crystallography continues to narrow, the use of EM maps to help with X-ray crystal structure determination, as described in this protocol, will become increasingly effective.« less

A competitive advantage by neonatally engrafted human glial progenitors yields mice whose brains are chimeric for human glia.

PubMed

Windrem, Martha S; Schanz, Steven J; Morrow, Carolyn; Munir, Jared; Chandler-Militello, Devin; Wang, Su; Goldman, Steven A

2014-11-26

Neonatally transplanted human glial progenitor cells (hGPCs) densely engraft and myelinate the hypomyelinated shiverer mouse. We found that, in hGPC-xenografted mice, the human donor cells continue to expand throughout the forebrain, systematically replacing the host murine glia. The differentiation of the donor cells is influenced by the host environment, such that more donor cells differentiated as oligodendrocytes in the hypomyelinated shiverer brain than in myelin wild-types, in which hGPCs were more likely to remain as progenitors. Yet in each recipient, both the number and relative proportion of mouse GPCs fell as a function of time, concomitant with the mitotic expansion and spread of donor hGPCs. By a year after neonatal xenograft, the forebrain GPC populations of implanted mice were largely, and often entirely, of human origin. Thus, neonatally implanted hGPCs outcompeted and ultimately replaced the host population of mouse GPCs, ultimately generating mice with a humanized glial progenitor population. These human glial chimeric mice should permit us to define the specific contributions of glia to a broad variety of neurological disorders, using human cells in vivo. Copyright © 2014 the authors 0270-6474/14/3416153-09$15.00/0.

Mobile dental operations: capital budgeting and long-term viability.

PubMed

Arevalo, Oscar; Chattopadhyay, Amit; Lester, Harold; Skelton, Judy

2010-01-01

The University of Kentucky College of Dentistry (UKCD) runs a large mobile dental operation. Economic conditions dictate that as the mobile units age it will be harder to find donors willing or able to provide the financial resources for asset replacement. In order to maintain current levels of access for the underserved, consideration of replacement is paramount. A financial analysis for a new mobile unit was conducted to determine self-sustainability, return on investment (ROI), and feasibility of generating a cash reserve for its replacement in 12 years. Information on clinical income, operational and replacement costs, and capital costs was collected. A capital budgeting analysis (CBA) was conducted using the Net Present Value (NPV) methodology in four different scenarios. Depreciation funding was calculated by transferring funds from cash inflows and reinvested to offset depreciation at fixed compound interest. A positive ROI was obtained for two scenarios. He depreciation fund did not generate a cash reserve sufficient to replace the mobile unit. Mobile dental programs can play a vital role in providing access to care to underserved populations and ensuring their mission requires long-term planning. Careful financial viability and CBA based on sound assumptions are excellent decision-making tools.

Continuous Processing of High Thermal Conductivity Polyethylene Fibers and Sheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-12-01

This factsheet describes a project that developed a new, continuous manufacturing process to make high molecular weight, high thermal conductivity polyethylene fibers and sheets to replace metals and ceramics in heat transfer applications.

Aggressive Treatment of Life-Threatening Hypophosphatemia During Recovery From Fulminant Hepatic Failure: A Case Report.

PubMed

Bissell, Brittany D; Davis, Jason E; Flannery, Alexander H; Adkins, David A; Thompson Bastin, Melissa L

2018-06-01

Acute liver failure secondary to acetaminophen overdose can be a life-threatening condition, characterized by severe electrolyte derangements. Hepatocyte regeneration is associated with phosphorous utilization and is a known complication of liver recovery following injury. We report the case of profound, life-threatening hypophosphatemia following recovery from acute fulminant liver failure. As the liver enzymes normalized, serum phosphorous levels plummeted. Our patient required an aggressive, individualized phosphorus replacement regimen, which resulted in a continuous infusion of intravenous (IV) sodium phosphate, titrated to a maximum rate of 30 mmol/h or 0.5 mmol/kg/h. The patient required over 400 mmol of total IV and oral phosphorous over the course of 48 hours. An aggressive approach to phosphorous replacement was done safely and effectively. Traditional replacement protocols are not adequate to sustain patients with this degree of hypophosphatemia. This is the first report to utilize a continuous infusion of phosphate with a maximum reported rate (0.5 mmol/kg/h). Our report summarizes a novel and safe approach for clinicians to maximally support these patients through high-dose, continuous infusion phosphorous administration.

First non-OEM steam-generator replacement in US a success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendsbee, P.M.; Lees, M.D.; Smith, J.C.

1994-04-01

In selecting replacements for major powerplant components, a fresh approach can be advantageous--even when complex nuclear components are involved. This was the experience at Unit 2 of Millstone nuclear station, which features an 870-MW pressurized-water reactor (PWR) with two nuclear recirculating steam generators. The unit began operation in 1975. In the early 1980s, pitting problems surfaced in the steam generator tubing; by the mid eighties, tube corrosion had reached an unacceptable level. Virtually all of the 17,000 tubes in the two units were deteriorating, with 2500 plugged and 5000 sleeved. Several new problems also were identified, including secondary-side circumferential crackingmore » of the Alloy 600 tubing near the tubesheet face, and deterioration of the carbon steel egg-crate tube supports. Despite improvements to primary and secondary steam-generator water chemistry, including almost complete copper removal from the condensate and feedwater loops, Northeast Utilities (NU) was unable to completely control degradation of the tube bundles. The utility decided in 1987 that full replacement was the most viable alternative. NU made a bold move, selecting a supplier other than the original equipment manufacturer (OEM).« less

Development of cyclic shedding teeth from semi-shedding teeth: the inner dental arcade of the stem osteichthyan Lophosteus

NASA Astrophysics Data System (ADS)

Chen, Donglei; Blom, Henning; Sanchez, Sophie; Tafforeau, Paul; Märss, Tiiu; Ahlberg, Per E.

2017-05-01

The numerous cushion-shaped tooth-bearing plates attributed to the stem group osteichthyan Lophosteus superbus, which are argued here to represent an early form of the osteichthyan inner dental arcade, display a previously unknown and presumably primitive mode of tooth shedding by basal hard tissue resorption. They carry regularly spaced, recumbent, gently recurved teeth arranged in transverse tooth files that diverge towards the lingual margin of the cushion. Three-dimensional reconstruction from propagation phase-contrast synchrotron microtomography (PPC-SRµCT) reveals remnants of the first-generation teeth embedded in the basal plate, a feature never previously observed in any taxon. These teeth were shed by semi-basal resorption with the periphery of their bases retained as dentine rings. The rings are highly overlapped, which evidences tooth shedding prior to adding the next first-generation tooth at the growing edge of the plate. The first generation of teeth is thus diachronous. Successor teeth at the same sites underwent cyclical replacing and shedding through basal resorption, producing stacks of buried resorption surfaces separated by bone of attachment. The number and spatial arrangement of resorption surfaces elucidates that basal resorption of replacement teeth had taken place at the older tooth sites before the addition of the youngest first-generation teeth at the lingual margin. Thus, the replacement tooth buds cannot have been generated by a single permanent dental lamina at the lingual edge of the tooth cushion, but must have arisen either from successional dental laminae associated with the individual predecessor teeth, or directly from the dental epithelium of these teeth. The virtual histological dissection of these Late Silurian microfossils broadens our understanding of the development of the gnathostome dental systems and the acquisition of the osteichthyan-type of tooth replacement.

"MARK I" MEASUREMENT METHODOLOGY FOR POLLUTION PREVENTION PROGRESS OCCURRING AS A RESULT OF PRODUCT DECISIONS

EPA Science Inventory

A methodology for assessing progress in pollution prevention resulting from product redesign, reformulation or replacement is described. The method compares the pollution generated by the original product with that from the modified or replacement product, taking into account, if...

Built to Last: The Army’s Failed Quest to Replace the Bradley Fighting Vehicle

DTIC Science & Technology

2015-05-23

Army believes that the BFV does not have the space, weight, or power needed on the modern battlefield. The persistent need for a replacement vehicle...the early 1980’s. The Army has long expressed the need to replace the Bradley Fighting Vehicle ( BFV ) with a new ground combat vehicle. The Bradley...one of the original Big Five, was designed to fight a Cold War threat. Requirements have changed since then but the Army continues to use the BFV

[A mathematic analysis of different manners of replacement fluid infusion in continuous veno-venous hemofiltration].

PubMed

Wu, Yunzhen; Wang, Chunting

2015-05-01

To establish a mathematical formula for choosing the manner of replacement fluid infusion in continuous renal replacement therapy (CRRT), so as to provide the basis for improving the treatment effect. A mathematical formula for choosing the manner of replacement fluid infusion with continuous veno-venous hemofiltration (CVVH) was taken as an example, and it was compared with the result of standard replacement fluid in order to analyze the effect of different manners of infusion. (1) Comparison parameters: the plasma volume ("Vreturn") and some electrolyte concentration ("Creturn") in back way of CRRT ( if other thing was solute, filter coefficient should be 1.0). (2) Research objects: the actual replacement fluid (for example, the most complex should be sorted into A and B type) mode (pre or post) was compared with the standard replacement fluid (the A and B in one). (3) Based on the formula of standard replacement, four equations in different conditions were derived: pre-dilution and post-dilution mode; same direction and same ratio; same direction and different ratio; different direction and same ratio; different direction and different ratio. The calculated results of "Vreturn" (except hematocrit) and "Creturn" were same to the standard only following the rule of same direction and ratio for A and B no matter pre-dilution mode or post-dilution mode, and it was different from the standard in others. In pre-dilution mode and post-dilution mode, it showed: (1) A and B in same direction and different ratio: "Vreturn" and "Creturn" were different from the standard for the alterative ratio of B. (2) A and B in different direction and same ratio: "Vreturn" was same to the standard, but "Creturn" was different from the standard for the completely different and more complex computational formula. (3) A and B in different direction and different ratio: both "Vreturn" and "Creturn" were different from the standard. The different "Vreturn" was due to the different ratio of B. The different "Creturn" was caused by different ratio of B and the completely different computational formula. (1) For parts of replacement fluid which must be separated (for example, bicarbonate formula), the result is same to the standard, and is predicted and mastered only following the rule of same direction and ratio. Otherwise, we need to calculate the two parameters over and over again. The result will run out of our judgment. The wrongness of losing water and electrolyte disorders maybe come out. (2) Accordingly,the formula could be used to analyze the same case like the separated replacement infusion, for example, a large number of citrates as regional anticoagulation were infused only in the front of filter, while the replacement fluid can be done in varied forms.

41 CFR 102-34.260 - May we replace a Government-owned motor vehicle sooner?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false May we replace a Government-owned motor vehicle sooner? 102-34.260 Section 102-34.260 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY...

41 CFR 102-34.260 - May we replace a Government-owned motor vehicle sooner?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false May we replace a Government-owned motor vehicle sooner? 102-34.260 Section 102-34.260 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY...

21 CFR 874.3540 - Prosthesis modification instrument for ossicular replacement surgery.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Prosthesis modification instrument for ossicular replacement surgery. 874.3540 Section 874.3540 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3540 Prosthesis modification...

21 CFR 874.3540 - Prosthesis modification instrument for ossicular replacement surgery.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Prosthesis modification instrument for ossicular replacement surgery. 874.3540 Section 874.3540 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3540 Prosthesis modification...

21 CFR 874.3540 - Prosthesis modification instrument for ossicular replacement surgery.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Prosthesis modification instrument for ossicular replacement surgery. 874.3540 Section 874.3540 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3540 Prosthesis modification...

21 CFR 874.3540 - Prosthesis modification instrument for ossicular replacement surgery.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Prosthesis modification instrument for ossicular replacement surgery. 874.3540 Section 874.3540 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3540 Prosthesis modification...

21 CFR 874.3540 - Prosthesis modification instrument for ossicular replacement surgery.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Prosthesis modification instrument for ossicular replacement surgery. 874.3540 Section 874.3540 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3540 Prosthesis modification...

42 CFR 424.350 - Replacement of checks that are lost, stolen, defaced, mutilated, destroyed, or paid on forged...

Code of Federal Regulations, 2010 CFR

2010-10-01

... CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM CONDITIONS FOR MEDICARE PAYMENT Replacement and Reclamation of Medicare Payments § 424.350... investigation and settlement of claims in connection with Treasury checks issued on behalf of CMS. (2) Action by...

46 CFR 56.01-1 - Scope (replaces 100.1).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Scope (replaces 100.1). 56.01-1 Section 56.01-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

46 CFR 56.01-1 - Scope (replaces 100.1).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Scope (replaces 100.1). 56.01-1 Section 56.01-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

46 CFR 56.01-1 - Scope (replaces 100.1).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Scope (replaces 100.1). 56.01-1 Section 56.01-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

46 CFR 56.01-1 - Scope (replaces 100.1).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Scope (replaces 100.1). 56.01-1 Section 56.01-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

46 CFR 56.01-1 - Scope (replaces 100.1).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Scope (replaces 100.1). 56.01-1 Section 56.01-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

46 CFR 56.65-1 - General (replaces 127 through 135).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false General (replaces 127 through 135). 56.65-1 Section 56.65-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING...). The requirements for fabrication, assembly and erection in subparts 56.70 through 56.90 shall apply in...

46 CFR 56.65-1 - General (replaces 127 through 135).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false General (replaces 127 through 135). 56.65-1 Section 56.65-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING...). The requirements for fabrication, assembly and erection in subparts 56.70 through 56.90 shall apply in...

46 CFR 56.65-1 - General (replaces 127 through 135).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false General (replaces 127 through 135). 56.65-1 Section 56.65-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING...). The requirements for fabrication, assembly and erection in subparts 56.70 through 56.90 shall apply in...

46 CFR 56.65-1 - General (replaces 127 through 135).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false General (replaces 127 through 135). 56.65-1 Section 56.65-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING...). The requirements for fabrication, assembly and erection in subparts 56.70 through 56.90 shall apply in...

46 CFR 56.65-1 - General (replaces 127 through 135).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false General (replaces 127 through 135). 56.65-1 Section 56.65-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING...). The requirements for fabrication, assembly and erection in subparts 56.70 through 56.90 shall apply in...

High phenobarbital clearance during continuous renal replacement therapy: a case report and pharmacokinetic analysis.

PubMed

Rosenborg, Staffan; Saraste, Lars; Wide, Katarina

2014-08-01

Phenobarbital is an old antiepileptic drug used in severe epilepsy. Despite this, little is written about the need for dose adjustments in renal replacement therapy. Most sources recommend a moderately increased dose guided by therapeutic drug monitoring.A 14 year old boy with nonketotic hyperglycinemia, a rare inborn error of metabolism, characterized by high levels of glycine, epilepsy, spasticity, and cognitive impairment, was admitted to the emergency department with respiratory failure after a few days of fever and cough. The boy was unconscious at admittance and had acute renal and hepatic failure.Due to the acute respiratory infection, hypoxic hepatic and renal failure occurred and the patient had a status epilepticus.The patient was intubated and mechanically ventilated. Continuous renal replacement therapy was initiated. Despite increased phenobarbital doses, therapeutic levels were not reached until the dose was increased to 500 mg twice daily. Therapeutic drug monitoring was performed in plasma and dialysate. Calculations revealed that phenobarbital was almost freely dialyzed.Correct dosing of drugs in patients on renal replacement therapy may need a multidisciplinary approach and guidance by therapeutic drug monitoring.

High Phenobarbital Clearance During Continuous Renal Replacement Therapy

PubMed Central

Rosenborg, Staffan; Saraste, Lars; Wide, Katarina

2014-01-01

Abstract Phenobarbital is an old antiepileptic drug used in severe epilepsy. Despite this, little is written about the need for dose adjustments in renal replacement therapy. Most sources recommend a moderately increased dose guided by therapeutic drug monitoring. A 14 year old boy with nonketotic hyperglycinemia, a rare inborn error of metabolism, characterized by high levels of glycine, epilepsy, spasticity, and cognitive impairment, was admitted to the emergency department with respiratory failure after a few days of fever and cough. The boy was unconscious at admittance and had acute renal and hepatic failure. Due to the acute respiratory infection, hypoxic hepatic and renal failure occurred and the patient had a status epilepticus. The patient was intubated and mechanically ventilated. Continuous renal replacement therapy was initiated. Despite increased phenobarbital doses, therapeutic levels were not reached until the dose was increased to 500 mg twice daily. Therapeutic drug monitoring was performed in plasma and dialysate. Calculations revealed that phenobarbital was almost freely dialyzed. Correct dosing of drugs in patients on renal replacement therapy may need a multidisciplinary approach and guidance by therapeutic drug monitoring. PMID:25101986

Permanent epicardial pacing in pediatric patients: 12-year experience at a single center.

PubMed

Kwak, Jae Gun; Kim, Soo-Jin; Song, Jin Young; Choi, Eun Young; Lee, Sang Yoon; Shim, Woo Sup; Lee, Chang-Ha; Lee, Cheul; Park, Chun Soo

2012-02-01

Permanent cardiac pacing is not often done in children, and when done is usually accomplished through epicardial pacing. We reviewed a 12-year experience with the implantation of epicardial pacemakers by our clinical group. Fifty-three patients who underwent their first implantation of an epicardial pacemaker before the age of 18 years and between 1997 and 2009 were included in our study. The mean age of the patients at the time of first pacemaker implantation was 5.7±4.8 years. Indications for pacemaker implantation included postoperative or congenital atrioventricular block and sinus node dysfunction. The patients underwent 105 operations for the replacement of pacemaker pulse generators and 75 operations for the replacement of pacemaker leads. The most commonly used generator mode was the rate-responsive accelerometer-based (DDDR) mode, which was used in 40.9% of the patients. We used more non-steroid-eluting leads (70.1%) than steroid-eluting leads (29.1%). The overall duration of follow-up in the study was 8.0±4.5 years (range, 2.1 months to approximately 17.0 years). Freedom from the need for generator replacement was 98.0%, 60.7%, and 11.1% at 1, 5, and 8 years, respectively. A tendency toward early generator exhaustion was observed among younger patients (p=0.058). The generator mode used for pacing did not significantly affect generator longevity. Freedom from the need for lead replacement was 98.3%, 83.8%, and 63.6% at 1, 5, and 10 years, respectively. The mean longevity of the leads used in the study was 10.8±0.8 years. Neither patient age at the time of lead implantation nor type of lead significantly affected lead longevity. Lead longevity was sufficiently long and did not vary significantly according to type of lead. Generator longevity was not affected by lead type, generator mode, or patient age at the time of pacemaker implantation. Copyright © 2012 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Preliminary results of the on-demand vortex-generator experiments

NASA Technical Reports Server (NTRS)

Saddoughi, Seyed G.

1995-01-01

This is a report on the continuation of our experimental investigations (Saddoughi 1994) of 'on-demand' vortex generators. Conventional vortex generators as found on aircraft wings are mainly for suppression of separation during the off-design conditions. In cruise they perform no useful function and exert a significant drag penalty. Therefore, replacement of fixed rectangular or delta-wing generators by devices that could be activated when needed would be of interest. Also in our previous report, we described one example of an 'on-demand' device, which was developed by Jacobson & Reynolds (1995) at Stanford University, suitable for manufacture by micro-electro-mechanical technology. This device consists of a surface cavity elongated in the stream direction and covered with a lid cantilevered at the upstream end. The lid, which is a metal sheet with a sheet of piezoelectric ceramic bonded to it, lies flush with the boundary. On application of a voltage the ceramic expands or contracts; however, adequate amplitude can be obtained only by running at the cantilever resonance frequency and applying amplitude modulation: for 2.5 mm x 20 mm cantilevered lids, they obtained maximum tip displacements of the order of 100 pm. Thus fluid is expelled from the cavity through the gap around the lid on the downstroke. They used an asymmetrical gap configuration and found that periodic emerging jets on the narrow side induced periodic longitudinal vorticity into the boundary layer. Their device was used to modify the inner layer of the boundary layer for skin-friction reduction. The same method could be implemented for the replacement of the conventional vortex generators; however, to promote mixing and suppress separation we needed to deposit longitudinal vortices into the outer layer of the boundary layer, which required a larger vortex generator than the device built by Jacobson & Reynolds. Our vortex generator was built with a mechanically-driven cantilevered lid with an adjustable frequency. The device was made about ten times the size of Jacobson & Reynolds', the shape or size of the cavity and lid (28 mm x 250 mm) could be easily changed. The cavity depth, the cantilever-tip displacement, and the maximum lid frequency were 20 mm, 10 mm, and 60 Hz respectively. Our vortex generator was mounted on a turntable so that its yaw angle could be changed. Finally, tests over a range of ratios of vortex generator size to boundary-layer thickness could be carried out simply by changing the streamwise location of the device.

Physics of Incandescent Lamp Burnout

ERIC Educational Resources Information Center

Gluck, Paul; King, John

2008-01-01

Incandescent lamps with tungsten filaments have been in use for about a century while being gradually replaced by fluorescent lamps; in another generation both will quite probably be largely replaced by light-emitting diodes. Incandescent lamps (simply called "lamps" in what follows) burn out after a lifetime that depends mostly on the temperature…

7 CFR 4280.178 - Scoring feasibility study grant applications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Energy for America Program General Renewable Energy System Feasibility Study Grants § 4280.178 Scoring... of 100 points possible. (a) Energy replacement or generation. The project can be for either... replacement. 25 points will be awarded if proposed project will offset any portion of the applicant's energy...

7 CFR 4280.178 - Scoring feasibility study grant applications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Energy for America Program General Renewable Energy System Feasibility Study Grants § 4280.178 Scoring... of 100 points possible. (a) Energy replacement or generation. The project can be for either... replacement. 25 points will be awarded if proposed project will offset any portion of the applicant's energy...

7 CFR 4280.178 - Scoring feasibility study grant applications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Energy for America Program General Renewable Energy System Feasibility Study Grants § 4280.178 Scoring... of 100 points possible. (a) Energy replacement or generation. The project can be for either... replacement. 25 points will be awarded if proposed project will offset any portion of the applicant's energy...

Decreased proliferative, migrative and neuro-differentiative potential of postnatal rat enteric neural crest-derived cells during culture in vitro

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Hui; Institute of Neurobiology, Environment and Genes Related to Diseases Key Laboratory of Chinese Ministry of Education, Xi’an Jiaotong University, No 96, Yan Ta Xi Road, Xi’an 710061, Shaanxi; Pan, Wei-Kang

A growing body of evidence supports the potential use of enteric neural crest-derived cells (ENCCs) as a cell replacement therapy for Hirschsprung's disease. Based on previous observations of robust propagation of primary ENCCs, as opposed to their progeny, it is suggested that their therapeutic potential after in vitro expansion may be restricted. We therefore examined the growth and differentiation activities and phenotypic characteristics of continuous ENCC cultures. ENCCs were isolated from the intestines of postnatal rats and were identified using an immunocytochemical approach. During continuous ENCC culture expansion, proliferation, migration, apoptosis, and differentiation potentials were monitored. The Cell Counting Kit-8more » was used for assessment of ENCC vitality, Transwell inserts for cell migration, immunocytochemistry for cell counts and identification, and flow cytometry for apoptosis. Over six continuous generations, ENCC proliferation potency was reduced and with prolonged culture, the ratio of migratory ENCCs was decreased. The percentage of apoptosis showed an upward trend with prolonged intragenerational culture, but showed a downward trend with prolonged culture of combined generations. Furthermore, the percentage of peripherin{sup +} cells decreased whilst the percentage of GFAP{sup +} cells increased with age. The results demonstrated that alterations in ENCC growth characteristics occur with increased culture time, which may partially account for the poor results of proposed cell therapies. - Highlights: • Differences were identified between primary and daughter ENCCs. • Daughter ENCCs had reduced proliferation, migration and differentiation. • Daughter ENCCs also had increased apoptosis. • These altered characteristics warrant further investigation.« less

Rapid breeding and varietal replacement are critical to adaptation of cropping systems in the developing world to climate change.

PubMed

Atlin, Gary N; Cairns, Jill E; Das, Biswanath

2017-03-01

Plant breeding is a key mechanism for adaptation of cropping systems to climate change. Much discussion of breeding for climate change focuses on genes with large effects on heat and drought tolerance, but phenology and stress tolerance are highly polygenic. Adaptation will therefore mainly result from continually adjusting allele frequencies at many loci through rapid-cycle breeding that delivers a steady stream of incrementally improved cultivars. This will require access to elite germplasm from other regions, shortened breeding cycles, and multi-location testing systems that adequately sample the target population of environments. The objective of breeding and seed systems serving smallholder farmers should be to ensure that they use varieties developed in the last 10 years. Rapid varietal turnover must be supported by active dissemination of new varieties, and active withdrawal of obsolete ones. Commercial seed systems in temperate regions achieve this through competitive seed markets, but in the developing world, most crops are not served by competitive commercial seed systems, and many varieties date from the end of the Green Revolution (the late 1970s, when the second generation of modern rice and wheat varieties had been widely adopted). These obsolete varieties were developed in a climate different than today's, placing farmers at risk. To reduce this risk, a strengthened breeding system is needed, with freer international exchange of elite varieties, short breeding cycles, high selection intensity, wide-scale phenotyping, and accurate selection supported by genomic technology. Governments need to incentivize varietal release and dissemination systems to continuously replace obsolete varieties.

7 CFR 1710.251 - Construction work plans-distribution borrowers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... generation facilities; (11) Load management equipment, automatic sectionalizing facilities, and centralized... transmission plant, and improvements replacements, and retirements of any generation plant. Construction of new generation capacity need not be included in a CWP but must be specified and supported by specific engineering...

Phosphate-containing dialysis solution prevents hypophosphatemia during continuous renal replacement therapy

PubMed Central

BROMAN, M; CARLSSON, O; FRIBERG, H; WIESLANDER, A; GODALY, G

2011-01-01

Background Hypophosphatemia occurs in up to 80% of the patients during continuous renal replacement therapy (CRRT). Phosphate supplementation is time-consuming and the phosphate level might be dangerously low before normophosphatemia is re-established. This study evaluated the possibility to prevent hypophosphatemia during CRRT treatment by using a new commercially available phosphate-containing dialysis fluid. Methods Forty-two heterogeneous intensive care unit patients, admitted between January 2007 and July 2008, undergoing hemodiafiltration, were treated with a new Gambro dialysis solution with 1.2 mM phosphate (Phoxilium) or with standard medical treatment (Hemosol B0). The patients were divided into three groups: group 1 (n=14) receiving standard medical treatment and intravenous phosphate supplementation as required, group 2 (n=14) receiving the phosphate solution as dialysate solution and Hemosol B0 as replacement solution and group 3 (n=14) receiving the phosphate-containing solution as both dialysate and replacement solutions. Results Standard medical treatment resulted in hypophosphatemia in 11 of 14 of the patients (group 1) compared with five of 14 in the patients receiving phosphate solution as the dialysate solution and Hemosol B0 as the replacement solution (group 2). Patients treated with the phosphate-containing dialysis solution (group 3) experienced stable serum phosphate levels throughout the study. Potassium, ionized calcium, magnesium, pH, pCO2 and bicarbonate remained unchanged throughout the study. Conclusion The new phosphate-containing replacement and dialysis solution reduces the variability of serum phosphate levels during CRRT and eliminates the incidence of hypophosphatemia. PMID:21039362

The Evolution of Dental Materials for Hybrid Prosthesis

PubMed Central

Gonzalez, Jorge

2014-01-01

Since the immemorial, the replacement of missing teeth has been a medical and cosmetic necessity for human kind. Nowadays, middle-aged population groups have experienced improved oral health, as compared to previous generations, and the percentage of edentulous adults can be expected to further decline. However, with the continued increase in the number of older adult population, it is anticipated that the need for some form of full-mouth restoration might increase from 53.8 million in 1991 to 61 million in 2020 [1]. Denture prosthetics has undergone many development stages since the first dentures were fabricated. The introduction of computer-aided design/computer aided manufacturing (CAD/CAM) has resulted in a more accurate manufacturing of prosthetic frameworks, greater accuracy of dental restorations, and in particular, implant supported prosthesis. PMID:24893781

The Invisible Army

PubMed Central

2017-01-01

ABSTRACT The “invisible army” of clinical microbiologists is facing major changes and challenges. The rate of change in both the science and technology is accelerating with no end in sight, putting pressure on our army to learn and adapt as never before. Health care funding in the United States is undergoing dramatic change which will require a new set of assumptions about how clinical microbiology is practiced here. A major challenge facing the discipline is the replacement of a generation of clinical microbiologists. In my opinion, it is incumbent on us in the invisible army to continue to work with the American Society for Microbiology (ASM) in meeting the future challenges faced by our discipline. In this commentary, I will first discuss some recent history of clinical microbiology within ASM and then some current challenges we face. PMID:28659316

A sub-microwatt asynchronous level-crossing ADC for biomedical applications.

PubMed

Li, Yongjia; Zhao, Duan; Serdijn, Wouter A

2013-04-01

A continuous-time level-crossing analog-to-digital converter (LC-ADC) for biomedical applications is presented. When compared to uniform-sampling (US) ADCs LC-ADCs generate fewer samples for various sparse biomedical signals. Lower power consumption and reduced design complexity with respect to conventional LC-ADCs are achieved due to: 1) replacing the n-bit digital-to-analog converter (DAC) with a 1-bit DAC; 2) splitting the level-crossing detections; and 3) fixing the comparison window. Designed and implemented in 0.18 μm CMOS technology, the proposed ADC uses a chip area of 220 × 203 μm(2). Operating from a supply voltage of 0.8 V, the ADC consumes 313-582 nW from 5 Hz to 5 kHz and achieves an ENOB up to 7.9 bits.

FEM analysis of an single stator dual PM rotors axial synchronous machine

NASA Astrophysics Data System (ADS)

Tutelea, L. N.; Deaconu, S. I.; Popa, G. N.

2017-01-01

The actual e - continuously variable transmission (e-CVT) solution for the parallel Hybrid Electric Vehicle (HEV) requires two electric machines, two inverters, and a planetary gear. A distinct electric generator and a propulsion electric motor, both with full power converters, are typical for a series HEV. In an effort to simplify the planetary-geared e-CVT for the parallel HEV or the series HEV we hereby propose to replace the basically two electric machines and their two power converters by a single, axial-air-gap, electric machine central stator, fed from a single PWM converter with dual frequency voltage output and two independent PM rotors. The proposed topologies, the magneto-motive force analysis and quasi 3D-FEM analysis are the core of the paper.

Advancing the Oxygen Generation Assembly Design to Increase Reliability and Reduce Costs for a Future Long Duration Mission

NASA Technical Reports Server (NTRS)

Takada, Kevin C.; Ghariani, Ahmed E.; Van Keuren,

2015-01-01

The state-of-the-art Oxygen Generation Assembly (OGA) has been reliably producing breathing oxygen for the crew aboard the International Space Station (ISS) for over eight years. Lessons learned from operating the ISS OGA have led to proposing incremental improvements to advance the baseline design for use in a future long duration mission. These improvements are intended to reduce system weight, crew maintenance time and resupply mass from Earth while increasing reliability. The proposed improvements include replacing the cell stack membrane material, deleting the nitrogen purge equipment, replacing the hydrogen sensors, deleting the wastewater interface, replacing the hydrogen dome and redesigning the cell stack power supply. The development work to date will be discussed and forward work will be outlined. Additionally, a redesigned system architecture will be proposed.

Brief history of intermolecular and intersurface forces in complex fluid systems.

PubMed

Israelachvili, Jacob; Ruths, Marina

2013-08-06

We review the developments of ideas, concepts, and theories of intermolecular and intersurface forces and how these were influenced (or ignored) by observations of nature and, later, systematic experimentation. The emphasis of this review is on the way things gradually changed: experimentation replaced rhetoric, measurement and quantification replaced hand waving, energy replaced force in calculations, discrete atoms replaced the (continuum) aether, thermodynamics replaced mechanistic models, randomness and probability replaced certainty, and delicate experiments on the subnanoscale revealed fascinating self-assembling structures and complex behavior of even the simplest systems. We conclude by discussing today's unresolved challenges: how complex "dynamic" multicomponent--especially living biological--systems that receive a continuous supply of energy can be far from equilibrium and not even in any steady state. Such systems, never static but evolving in both space and time, are still far from being understood both experimentally and theoretically.

7 CFR 160.83 - Miscellaneous receipts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND... moneys received or withheld to cover the cost of repairs, or of replacing any missing parts of duplicates...

7 CFR 160.82 - Return of security.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND... secured thereby: Provided, That before refund is made the cost of any repairs or replacement shall be...

Three Years of on Orbit ISS Oxygen Generation System Operation 2007-2010

NASA Technical Reports Server (NTRS)

Diderich, Greg S.; Polis, Pete; VanKeuren, Steven P.; Erickson, Bob

2010-01-01

The International Space Station (ISS) United States Orbital Segment (USOS) Oxygen Generation System (OGS) has accumulated 240 days of continuous operation at varied oxygen production rates within the US Laboratory Module (LAB) since it was first activated in July 2007. OGS relocated from the ISS LAB to Node 3 during 20A Flight (February 2010). The OGS rack delivery was accelerated for on-orbit checkout in the LAB, and it was launched to ISS in July of 2006. During the on-orbit checkout interval within the LAB from July 2007 to October 2008, OGS operational times were limited by the quantity of feedwater in a Payload Water Reservoir (PWR) bag. Longer runtimes are now achievable due to the continuous feedwater availability after ULF2 delivery and activation of the USOS Water Recovery System (WRS) racks. OGS is considered a critical function to maintaining six crew capability. There have been a number of failures which interrupted or threatened to interrupt oxygen production. Filters in the recirculation loop have clogged and have been replaced, Hydrogen sensors have fallen out of specifications, a pump delta pressure sensor failed, a pump failed to start, and the voltage on the cell stack increased out of tolerance. This paper will discuss the operating experience and characteristics of the OGS, as well as operational issues and their resolution.

Therapeutic Plasma Exchange in Critically Ill Children Requiring Intensive Care.

PubMed

Cortina, Gerard; McRae, Rosemary; Chiletti, Roberto; Butt, Warwick

2018-02-01

To characterize the clinical indications, procedural safety, and outcome of critically ill children requiring therapeutic plasma exchange. Retrospective observational study based on a prospective registry. Tertiary and quaternary referral 30-bed PICU. Forty-eight critically ill children who received therapeutic plasma exchange during an 8-year period (2007-2014) were included in the study. Therapeutic plasma exchange. A total of 48 patients underwent 244 therapeutic plasma exchange sessions. Of those, therapeutic plasma exchange was performed as sole procedure in 193 (79%), in combination with continuous renal replacement therapy in 40 (16.4%) and additional extracorporeal membrane oxygenation in 11 (4.6%) sessions. The most common admission diagnoses were hematologic disorders (30%), solid organ transplantation (20%), neurologic disorders (20%), and rheumatologic disorders (15%). Complications associated with the procedure occurred in 50 (21.2%) therapeutic plasma exchange sessions. Overall, patient survival from ICU was 82%. Although patients requiring therapeutic plasma exchange alone (n = 31; 64%) had a survival rate of 97%, those with additional continuous renal replacement therapy (n = 13; 27%) and extracorporeal membrane oxygenation (n = 4; 8%) had survival rates of 69% and 50%, respectively. Factors associated with increased mortality were lower Pediatric Index of Mortality 2 score, need for mechanical ventilation, higher number of failed organs, and longer ICU stay. Our results indicate that, in specialized centers, therapeutic plasma exchange can be performed relatively safely in critically ill children, alone or in combination with continuous renal replacement therapy and extracorporeal membrane oxygenation. Outcome in children requiring therapeutic plasma exchange alone is excellent. However, survival decreases with the number of failed organs and the need for continuous renal replacement therapy and extracorporeal membrane oxygenation.

34 CFR 200.43 - Restructuring.

Code of Federal Regulations, 2011 CFR

2011-07-01

... substantial promise of enabling the school to make AYP as defined under §§ 200.13 through 200.20; (3) Is... § 200.34, the LEA must do the following: (1) Continue to provide all students enrolled in the school...) Replace all or most of the school staff (which may include, but may not be limited to, replacing the...

34 CFR 200.43 - Restructuring.

Code of Federal Regulations, 2012 CFR

2012-07-01

... substantial promise of enabling the school to make AYP as defined under §§ 200.13 through 200.20; (3) Is... § 200.34, the LEA must do the following: (1) Continue to provide all students enrolled in the school...) Replace all or most of the school staff (which may include, but may not be limited to, replacing the...

34 CFR 200.43 - Restructuring.

Code of Federal Regulations, 2013 CFR

2013-07-01

... substantial promise of enabling the school to make AYP as defined under §§ 200.13 through 200.20; (3) Is... § 200.34, the LEA must do the following: (1) Continue to provide all students enrolled in the school...) Replace all or most of the school staff (which may include, but may not be limited to, replacing the...

34 CFR 200.43 - Restructuring.

Code of Federal Regulations, 2014 CFR

2014-07-01

... substantial promise of enabling the school to make AYP as defined under §§ 200.13 through 200.20; (3) Is... § 200.34, the LEA must do the following: (1) Continue to provide all students enrolled in the school...) Replace all or most of the school staff (which may include, but may not be limited to, replacing the...

Measure Guideline. Replacing Single-Speed Pool Pumps with Variable Speed Pumps for Energy Savings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, A.; Easley, S.

2012-05-01

This measure guideline evaluates potential energy savings by replacing traditional single-speed pool pumps with variable speed pool pumps, and provides a basic cost comparison between continued uses of traditional pumps verses new pumps. A simple step-by-step process for inspecting the pool area and installing a new pool pump follows.

Measure Guideline: Replacing Single-Speed Pool Pumps with Variable Speed Pumps for Energy Savings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, A.; Easley, S.

2012-05-01

The report evaluates potential energy savings by replacing traditional single-speed pool pumps with variable speed pool pumps, and provide a basic cost comparison between continued uses of traditional pumps verses new pumps. A simple step-by-step process for inspecting the pool area and installing a new pool pump follows.

31 CFR 321.21 - Replacement and recovery of losses.

Code of Federal Regulations, 2010 CFR

2010-07-01

... liability for such loss under 31 U.S.C. 3126(a), the Bureau of the Public Debt will demand that the paying... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Replacement and recovery of losses. 321.21 Section 321.21 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued...

META 2f: Probabilistic, Compositional, Multi-dimension Model-Based Verification (PROMISE)

DTIC Science & Technology

2011-10-01

Equational Logic, Rewriting Logic, and Maude ................................................ 52  5.3  Results and Discussion...and its discrete transitions are left unchanged. However, the differential equations describing the continuous dynamics (in each mode) are replaced by...by replacing hard-to-analyze differential equations by discrete transitions. In principle, predicate and qualitative abstraction can be used on a

Applicability of STEM-RTG and High-Power SRG Power Systems to the Discovery and Scout Mission Capabilities Expansion (DSMCE) Study of ASRG-Based Missions

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.; Cataldo, Robert L.

2015-01-01

This study looks at the applicability of utilizing the Segmented Thermoelectric Modular Radioisotope Thermoelectric Generator (STEM-RTG) or a high-power radioisotope generator to replace the Advanced Stirling Radioisotope Generator (ASRG), which had been identified as the baseline power system for a number of planetary exploration mission studies. Nine different Discovery-Class missions were examined to determine the applicability of either the STEM-RTG or the high-power SRG power systems in replacing the ASRG. The nine missions covered exploration across the solar system and included orbiting spacecraft, landers and rovers. Based on the evaluation a ranking of the applicability of each alternate power system to the proposed missions was made.

13. INTERIOR OF POWER PLANT LOOKING EASTNORTHEAST. 1925 GE GENERATOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. INTERIOR OF POWER PLANT LOOKING EAST-NORTHEAST. 1925 GE GENERATOR IN FOREGROUND, WITH C. 1910 GENERATOR COVER IN BACKGROUND. STEEL FRAME SUPPORTS HOISTING MECHANISM USED TO MOVE, REPAIR, OR REPLACE GENERATORS. - Potomac Power Plant, On West Virginia Shore of Potomac River, about 1 mile upriver from confluence with Shenandoah River, Harpers Ferry, Jefferson County, WV

XCII. A Low-Cost Voltammetric Signal Generator for the Electroanalytical Chemistry Laboratory

ERIC Educational Resources Information Center

Ewing, Galen W., Ed

1977-01-01

Describes the construction of a versatile signal generator suitable for use in cyclic voltammetric experiments, which can also be adapted to a conventional dc polarograph by replacing its ramp source. (MLH)

7 CFR 160.78 - Loss or damage of standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND.... The cost of making necessary repairs to any duplicates, or of replacing those damaged beyond repair...

77 FR 43176 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-24

... alternating current (AC) generator failures in-service due to incomplete fusion in the weld joint of the rotor band assembly. This proposed AD would require inspecting the AC generator to determine the part number, and replacing the AC generator if necessary. We are proposing this AD to prevent rotor windings from...

77 FR 43550 - Airworthiness Directives; Turbomeca S.A. Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-25

... dust collected during cleaning exceeds 8 grams. This proposed AD also includes an optional terminating... dust collected during any cleaning inside the gas generator hollow shaft exceeds 8 grams; and If there... gas generator hollow shaft is more than 8 grams, replace the gas generator rear bearing before further...

Meniscal tears, repairs and replacement: their relevance to osteoarthritis of the knee.

PubMed

McDermott, Ian

2011-04-01

The menisci of the knee are important load sharers and shock absorbers in the joint. Meniscal tears are common, and whenever possible meniscal tears should be surgically repaired. Meniscectomy leads to a significant increased risk of osteoarthritis, and various options now exist for replacing missing menisci, including the use of meniscal scaffolds or the replacement of the entire meniscus by meniscal allograft transplantation. The field of meniscal surgery continues to develop apace, and the future may lie in growing new menisci by tissue engineering techniques.

COMBINED REPLACEMENT OF THE AORTIC VALVE AND ASCENDING AORTA IN JEHOVAH'S WITNESSES: REPORT OF TWO CASES

PubMed Central

Beddermann, Christoph; Norman, John C.; Cooley, Denton A.

1979-01-01

Two Jehovah's Witnesses with large ascending thoracic aortic aneurysms and aortic insufficiency secondary to annuloaortic ectasia underwent successful combined replacement of the aortic valve and the ascending aorta. One patient received a composite graft containing an aortic valve prosthesis, which necessitated supravalvular coronary ostia reimplantation; the other patient underwent separate aortic valve and left supracoronary ascending aneurysm replacement, with reimplantation of the right coronary ostium into the graft. No blood or blood derivatives were administered. Both patients had uneventful recoveries and continue to do well. To our knowledge, they represent the first reported cases of successful combined replacement of the aortic valve and ascending aorta in Jehovah's Witnesses. Images PMID:15216324

Generation of diverse neural cell types through direct conversion

PubMed Central

Petersen, Gayle F; Strappe, Padraig M

2016-01-01

A characteristic of neurological disorders is the loss of critical populations of cells that the body is unable to replace, thus there has been much interest in identifying methods of generating clinically relevant numbers of cells to replace those that have been damaged or lost. The process of neural direct conversion, in which cells of one lineage are converted into cells of a neural lineage without first inducing pluripotency, shows great potential, with evidence of the generation of a range of functional neural cell types both in vitro and in vivo, through viral and non-viral delivery of exogenous factors, as well as chemical induction methods. Induced neural cells have been proposed as an attractive alternative to neural cells derived from embryonic or induced pluripotent stem cells, with prospective roles in the investigation of neurological disorders, including neurodegenerative disease modelling, drug screening, and cellular replacement for regenerative medicine applications, however further investigations into improving the efficacy and safety of these methods need to be performed before neural direct conversion becomes a clinically viable option. In this review, we describe the generation of diverse neural cell types via direct conversion of somatic cells, with comparison against stem cell-based approaches, as well as discussion of their potential research and clinical applications. PMID:26981169

Coupling Adaptation Tipping Points and Engineering Options: New Insights for Resilient Water Infrastructure Replacement Planning

NASA Astrophysics Data System (ADS)

Smet, K.; de Neufville, R.; van der Vlist, M.

2017-12-01

This work presents an innovative approach for replacement planning for aging water infrastructure given uncertain future conditions. We draw upon two existing methodologies to develop an integrated long-term replacement planning framework. We first expand the concept of Adaptation Tipping Points to generate long-term planning timelines that incorporate drivers of investment related to both internal structural processes as well as changes in external operating conditions. Then, we use Engineering Options to explore different actions taken at key moments in this timeline. Contrasting to the traditionally more static approach to infrastructure design, designing the next generation of infrastructure so it can be changed incrementally is a promising method to safeguard current investments given future uncertainty. This up-front inclusion of structural options in the system actively facilitates future adaptation, transforming uncertainty management in infrastructure planning from reactive to more proactive. A two-part model underpins this approach. A simulation model generates diverse future conditions, allowing development of timelines of intervention moments in the structure's life. This feeds into an economic model, evaluating the lifetime performance of different replacement strategies, making explicit the value of different designs and their flexibility. A proof of concept study demonstrates this approach for a pumping station. The strategic planning timelines for this structure demonstrate that moments when capital interventions become necessary due to reduced functionality from structural degradation or changed operating conditions are widely spread over the structure's life. The disparate timing of these necessary interventions supports an incremental, adaptive mindset when considering end-of-life and replacement decisions. The analysis then explores different replacement decisions, varying the size and specific options included in the proposed new structure. Results show that incremental adaptive designs and incorporating options can improve economic performance, as compared to traditional, "build it once & build it big" designs. The benefit from incorporating flexibility varies with structural functionality, future conditions and the specific options examined.

"Life without nuclear power": A nuclear plant retirement formulation model and guide based on economics. San Onofre Nuclear Generating Station case: Economic impacts and reliability considerations leading to plant retirement

NASA Astrophysics Data System (ADS)

Wasko, Frank

Traditionally, electric utilities have been slow to change and very bureaucratic in nature. This culture, in and of itself, has now contributed to a high percentage of United States electric utilities operating uneconomical nuclear plants (Crooks, 2014). The economic picture behind owning and operating United States nuclear plants is less than favorable for many reasons including rising fuel, capital and operating costs (EUCG, 2012). This doctoral dissertation is specifically focused on life without nuclear power. The purpose of this dissertation is to create a model and guide that will provide electric utilities who currently operate or will operate uneconomical nuclear plants the opportunity to economically assess whether or not their nuclear plant should be retired. This economic assessment and stakeholder analysis will provide local government, academia and communities the opportunity to understand how Southern California Edison (SCE) embraced system upgrade import and "voltage support" opportunities to replace "base load" generation from San Onofre Nuclear Generating Station (SONGS) versus building new replacement generation facilities. This model and guide will help eliminate the need to build large replacement generation units as demonstrated in the SONGS case analysis. The application of The Nuclear Power Retirement Model and Guide will provide electric utilities with economic assessment parameters and an evaluation assessment progression needed to better evaluate when an uneconomical nuclear plant should be retired. It will provide electric utilities the opportunity to utilize sound policy, planning and development skill sets when making this difficult decision. There are currently 62 nuclear power plants (with 100 nuclear reactors) operating in the United States (EIA, 2014). From this group, 38 are at risk of early retirement based on the work of Cooper (2013). As demonstrated in my model, 35 of the 38 nuclear power plants qualify to move to the economic assessment review and then on to the stakeholder cost benefit analysis (if model qualifications are met) leading to a final plant retirement decision. This application via the model and guide, in turn, will lead electric utilities to explore system upgrade import opportunities and mitigation measures versus building new replacement generation facilities. United States nuclear reactors are licensed for 40 years with a 20 year extension available prior to the expiration date (EIA, 2013). Since late 2012, electric power companies have announced the early retirement of four uneconomical nuclear power plants while other studies have indicated that as many as 70 percent of United States nuclear power plants are potentially at risk for early retirement (Crooks, 2014 and Cooper, 2013). A high percentage of these aforementioned nuclear plants have operating licenses that will not expire until 2030 and beyond. Thus, for the most part, replacement power contingency planning has not been initiated for these plants or is still in preliminary stages. The recent nuclear plant retirements are the first since 1998 (EIA, 2013). Decisions to retire the plants involved concerns over maintenance and repair costs as well as declining profitability (EIA, 2013). In addition, the Energy Information Administration (2010-2012) released data that demonstrated that the worst 25 percent of United States nuclear plants are far more expensive to operate and generate electricity than new gas plants. It is equally important to understand and explain the economic and power replacement implications to both ratepayers and end-users. A SONGS case study analysis will review the economic, operational and political challenges that SCE faced leading to the retirement decision of SONGS. As preface to the case study, replacement steam generators (RSGs) were installed in Unit 2 in 2009 and in Unit 3 in 2010. In January 2012, while Unit 2 was down for routine maintenance, a small leak was discovered inside a steam generator in Unit 3. Because of the situation, both units remained shut down to evaluate the cause of the leakage and to make repairs. SCE submitted plans to the Nuclear Regulatory Commission (NRC) to re-start Unit 2 at reduced power. However, concerns over the length of the review process and the high costs associated with steam generator repairs led SCE to retire both reactors (SCE SONGS Fact Sheets, 2012-2013). Finally, collaborative resource power replacement planning is needed more than ever as nuclear facilities in the United States are now being retired for economic related reasons (Crooks, 2014). This collaborative power replacement process and implementation must encompass all relevant stakeholders including state grid operators, ratepayers, shareholders and the electric utility company.

Continuities in stone flaking technology at Liang Bua, Flores, Indonesia.

PubMed

Moore, M W; Sutikna, T; Jatmiko; Morwood, M J; Brumm, A

2009-11-01

This study examines trends in stone tool reduction technology at Liang Bua, Flores, Indonesia, where excavations have revealed a stratified artifact sequence spanning 95k.yr. The reduction sequence practiced throughout the Pleistocene was straightforward and unchanging. Large flakes were produced off-site and carried into the cave where they were reduced centripetally and bifacially by four techniques: freehand, burination, truncation, and bipolar. The locus of technological complexity at Liang Bua was not in knapping products, but in the way techniques were integrated. This reduction sequence persisted across the Pleistocene/Holocene boundary with a minor shift favoring unifacial flaking after 11ka. Other stone-related changes occurred at the same time, including the first appearance of edge-glossed flakes, a change in raw material selection, and more frequent fire-induced damage to stone artifacts. Later in the Holocene, technological complexity was generated by "adding-on" rectangular-sectioned stone adzes to the reduction sequence. The Pleistocene pattern is directly associated with Homo floresiensis skeletal remains and the Holocene changes correlate with the appearance of Homo sapiens. The one reduction sequence continues across this hominin replacement.

Use of mock-up training to reduce personnel exposure at the North Anna Unit 1 Steam Generator Replacement Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henry, H.G.; Reilly, B.P.

1995-03-01

The North Anna Power Station is located on the southern shore of Lake Anna in Louisa County, approximately forty miles northwest of Richmond, Virginia. The two 910 Mw nuclear units located on this site are owned by Virginia Electric and Power Company (Virginia Power) and Old Dominion Electric Cooperative and operated by Virginia Power. Fuel was loaded into Unit 1 in December 1977, and it began commercial operation in June 1978. Fuel was loaded into Unit 2 in April 1980 and began commercial operation in December 1980. Each nuclear unit includes a three-coolant-loop pressurized light water reactor nuclear steam supplymore » system that was furnished by Westinghouse Electric Corporation. Included within each system were three Westinghouse Model 51 steam generators with alloy 600, mill-annealed tubing material. Over the years of operation of Unit 1, various corrosion-related phenomena had occurred that affected the steam generators tubing and degraded their ability to fulfill their heat transfer function. Advanced inspection and repair techniques helped extend the useful life of the steam generators, but projections based on the results of the inspections indicated that the existing steam generators tubing and degraded their ability to fullfill their heat transfer function. Advanced inspection and repair techniques helped extend the useful life of the steam generators, but projections based on the results of the inspections indicated that the existing steam generators would not last their design life and must be repaired. To this end Virginia Power determined that a steam generator replacement (SGR) program was necessary to remove the old steam generator tube bundles and lower shell sections, including the channel heads (collectively called the lower assemblies), and replace them with new lower assemblies incorporating design features that will prevent the degradation problems that the old steam generators had experienced.« less

Alternatives across Latin America: catalysing change in the curriculum.

PubMed

Jukes, Nick

2009-01-01

A 6-week series of seminars addressing replacement of harmful animal use in education and training was held across Latin America in March-April 2008. Organised by InterNICHE and partner organisations in Bolivia, Peru, Brazil, Argentina and Mexico, the events built on the experience of previous major outreach in Russia and India. Up to 6 full-day seminars were held at universities and independent venues in each country. Smaller meetings with campaigners, teachers and professional bodies complemented the large presentations. All events included spoken presentations, demonstrations and free trials of a wide range of alternatives. Speakers included InterNICHE experts and those from the host countries who are involved in replacement work. Partner organisations were empowered through the process of planning and execution of the seminars, and the tour helped to identify and provide support to others who are progressing humane education initiatives. Further collaboration is now planned. Information on the current situation concerning animal use and alternatives, including laws and regulations, was also gathered from each country. The tour succeeded in raising awareness and generating interest in replacement alternatives, also by national-level interviews and media coverage. Information and freeware alternatives were widely distributed, and further translations of material into Spanish and Portuguese are in progress. To continue the hands-on access to alternatives provided at the seminars, a Mexican / Central American Alternatives Loan System has been established, and others are being built in Peru and Brasil. The donation of computers and alternatives to selected universities is also being planned in order to establish multimedia laboratories that will promote alternatives through example.

Status of the ISS Trace Contaminant Control System

NASA Technical Reports Server (NTRS)

Macatangay, Ariel V.; Perry, Jay L.; Johnson, Sharon A.; Belcher, Paul A.

2009-01-01

A habitable atmosphere is a fundamental requirement for human spaceflight. To meet such a requirement, the cabin atmosphere must be constantly scrubbed to maintain human life and system functionality. The primary system for atmospheric scrubbing of the US on-orbit segment (USOS) of the International Space Station (ISS) is the Trace Contaminant Control System (TCCS). As part of the Environmental Control and Life Support Systems (ECLSS) atmosphere revitalization rack in the US Lab, the TCCS operates continuously, scrubbing trace contaminants generated primarily by two sources: the metabolic offgassing of crew members and the offgassing of equipment in the ISS. It has been online for approximately 95% since activated in February 2001. The TCCS is comprised of a charcoal bed, a catalytic oxidizer, and a lithium hydroxide post-sorbent bed, all of which are designed to be replaced onorbit when necessary. In 2006, all three beds were replaced following an observed increase in the system resistance that occurred over a period several months. The beds were returned to ground and subjected to a test, teardown and evaluation to investigate the root cause(s) of the decrease in flow rate through the system. In addition, various chemical and physical analyses of the bed materials were performed to determine contaminant loading and any changes in performance. This paper will mainly focus on the results of these analyses and how this correlates with what has been observed from archival sampling and onorbit events. This may provide insight into the future performance of the TCCS and rate of change for orbital replacement units in the TCCS.

CONVERTING FROM BATCH TO CONTINUOUS INTENSIFIED PROCESSING IN THE STT? REACTOR

EPA Science Inventory

The fluid dynamics, the physical dimensions and characteristics of the reaction zones of continuous process intensification reactors are often quite different from those of the batch reactors they replace. Understanding these differences is critical to the successful transit...

Research on PM2.5 emission reduction path of China ‘s electric power industry based on DEA model

NASA Astrophysics Data System (ADS)

Jin, Yanming; Yang, Fan; Liu, Jun

2018-02-01

Based on the theory of data envelopment analysis, this study constructs the environmental performance evaluation model of the power industry, analyzes the performance of development of clean energy, the implementation of electricity replacement, and the development of coal-fired energy-saving and emission-reducing measures. Put forward technology path to reduce emission in the future. The results show that (1) improving the proportion of coal for power generation, speeding up the replacement of electricity is the key to solve the haze in China. (2) With the photovoltaic and other new energy power generation costs gradually reduced and less limit from thermal energy, by final of “thirteenth five-years plan”, the economy of clean energy will surpass thermal energy-saving emission reduction. (3) After 2025, the economy of the electricity replacement will be able to show.

41 CFR 102-34.265 - May we keep a Government-owned motor vehicle even though the standard permits replacement?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false May we keep a Government-owned motor vehicle even though the standard permits replacement? 102-34.265 Section 102-34.265 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY 34...

Assessment of Service Life for Regenerative ECLSS Resin Beds

NASA Technical Reports Server (NTRS)

Cloud, Dale L.; Keilich, Maria C.; Polis, Peter C.; Yanczura, Stephen J.

2013-01-01

The International Space Station (ISS) Water Processor Assembly (WPA) and Oxygen Generation Assembly (OGA) manage and process water at various levels of cleanliness for multiple purposes. The effluent of theWPA and the influent of the OGA require water at very high levels of purity. The bulk of the water purification that occurs in both systems is performed by consumable activated carbon and ion exchange resin beds. Replacement beds must be available on orbit in order to continue the ISS critical processes of water purification and oxygen generation. Various hurdles exist in order to ensure viable spare resin beds. These include the characteristics of resin beds such as: storage environment, shelf life requirements, microbial growth, and variations in the levels and species of contaminants the beds are required to remove. Careful consideration has been given to match water models, bed capacities and spares traffic models to ensure that spares are always viable. The results of these studies and considerations, in particular, how shelf life requirements affect resin bed life management, are documented in this paper.

Microbial utilization of electrically reduced neutral red as the sole electron donor for growth and metabolite production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, D.H.; Laivenieks, M.; Guettler, M.V.

1999-07-01

Electrically reduced neutral red (NR) served as the sole source of reducing power for growth and metabolism of pure and mixed cultures of H[sub 2]-consuming bacteria in a novel electrochemical bioreactor system. NR was continuously reduced by the cathodic potential ([minus]1.5 V) generated from an electric current (0.3 to 1.0 mA), and it was subsequently oxidized by Actinobacillus succinogenes or by mixed methanogenic cultures. The A. succinogenes mutant strain FZ-6 did not grow on fumarate alone unless electrically reduced NR or hydrogen was present as the electron donor for succinate production. The mutant strain, unlike the wild type, lacked pyruvatemore » formate lyase and formate dehydrogenase. Electrically reduced NR also replaced hydrogen as the sole electron donor source for growth and production of methane from CO[sub 2]. These results show that both pure and mixed cultures can function as electrochemical devices when electrically generated reducing power can be used to drive metabolism. The potential utility of utilizing electrical reducing power in enhancing industrial fermentations or biotransformation processes is discussed.« less

Microfluidic Bead Suspension Hopper

PubMed Central

2014-01-01

Many high-throughput analytical platforms, from next-generation DNA sequencing to drug discovery, rely on beads as carriers of molecular diversity. Microfluidic systems are ideally suited to handle and analyze such bead libraries with high precision and at minute volume scales; however, the challenge of introducing bead suspensions into devices before they sediment usually confounds microfluidic handling and analysis. We developed a bead suspension hopper that exploits sedimentation to load beads into a microfluidic droplet generator. A suspension hopper continuously delivered synthesis resin beads (17 μm diameter, 112,000 over 2.67 h) functionalized with a photolabile linker and pepstatin A into picoliter-scale droplets of an HIV-1 protease activity assay to model ultraminiaturized compound screening. Likewise, trypsinogen template DNA-coated magnetic beads (2.8 μm diameter, 176,000 over 5.5 h) were loaded into droplets of an in vitro transcription/translation system to model a protein evolution experiment. The suspension hopper should effectively remove any barriers to using suspensions as sample inputs, paving the way for microfluidic automation to replace robotic library distribution. PMID:24761972

The Politics of the Academies Programme: Natality and Pluralism in Education Policy-Making

ERIC Educational Resources Information Center

Gunter, Helen M.; McGinity, Ruth

2014-01-01

Our investigations into the politics of the Academies Programme in England have generated thinking that draws on data about the conversion process from two projects. We engage with an early City Academy that replaced two "failing" schools, and a recent Academy that replaced a "successful" high school. We deploy Hannah Arendt's…

Diesel Goes Digital to Save Energy, Lower Emissions

NASA Technical Reports Server (NTRS)

2004-01-01

Forty years ago, actuators requiring constant energy to help power the Apollo spacecraft in space were replaced by magnetically holding and releasing, electronically controlled valves. Today, these same magnetic, electronic valves are on the verge of replacing entire camshaft systems in cars and trucks on Earth, thus leading to a whole new generation of low-emission engines.

One-Piece Faraday Generator: A Paradoxical Experiment from 1851

ERIC Educational Resources Information Center

Crooks, M. J.; And Others

1978-01-01

Describes an experiment based on Faraday's one-piece generator, where the rotating disk is replaced by a cylindrical permanent magnet. Explains the apparent paradox that an observer in an inertial frame could measure his absolute velocity. (GA)

[Strategies to Cope with the Shortage of Technologists: Facing the Mass-Retirement of the 'Baby-Boomer' Generation].

PubMed

Morikane, Keita; Yamada, Miyuki

2015-03-01

In Japan, the primary 'baby-boomer' generation, born between 1947 and 1949, is now in its retirement. This has caused a marked shortage of human resources nationwide. Clinical laboratory technologists are no exception, and many clinical laboratories in Japanese healthcare facilities are struggling with management because the number of new graduates, i.e., newly licensed technologists, is mostly fixed and, therefore, their recruitment is becoming more and more competitive. Our laboratory is now facing a wave of mass-retirement associated with our history. In addition, in the early 2000s, there was almost no position for new graduates replacing those retiring because of the change in the social healthcare system as well as our hospital's policy. This resulted in uneven numbers of technologists in generations, and it seemed to be getting worse. Fortunately, five years ago, the direction of social health care was changed and lots of positions became available as a result. We have been trying to recruit new graduates and experienced technologists as well, and were able to hire 18 people. Among them, 8 were non-freshmen. The generation gap has been mostly resolved. We will continue to make our laboratory more attractive not just to new graduates but also to experienced technologists, especially those who wish to return to work after a several-year absence to raise their children. We believe that this will energize our laboratory.

Device Longevity in a Contemporary Cohort of ICD/CRT-D Patients Undergoing Device Replacement.

PubMed

Zanon, Francesco; Martignani, Cristian; Ammendola, Ernesto; Menardi, Endrj; Narducci, Maria Lucia; DE Filippo, Paolo; Santamaria, Matteo; Campana, Andrea; Stabile, Giuseppe; Potenza, Domenico Rosario; Pastore, Gianni; Iori, Matteo; LA Rosa, Concetto; Biffi, Mauro

2016-07-01

The longevity of defibrillators (ICD) is extremely important from both a clinical and economic perspective. We studied the reasons for device replacement, the longevity of removed ICD, and the existence of possible factors associated with shorter service life. Consecutive patients who underwent ICD replacement from March 2013 to May 2015 in 36 Italian centers were included in this analysis. Data on replaced devices were collected. A total of 953 patients were included in this analysis. In 813 (85%) patients the reason for replacement was battery depletion, while 88 (9%) devices were removed for clinical reasons and the remaining 52 because of system failure (i.e., lead or ICD generator failure or a safety advisory indication). The median service life was 5.9 years (25th-75th percentile, 4.9-6.9) for single- and dual-chamber ICD and 4.9 years (25th-75th percentile, 4.0-5.7) for CRT-D. On multivariate analysis, the factors CRT-D device, SC/DC ICD generator from Biotronik, percentage of ventricular pacing, and the occurrence of a system failure were positively associated with a replacement procedure. By contrast, the device from Boston Scientific was an independent protective factor against replacement. Considerable differences were seen in battery duration in both ICD and CRT-D. Specifically, Biotronik devices showed the shortest longevity among ICD and Boston Scientific showed the longest longevity among CRT-D (log-rank test, P < 0.001 for pairwise comparisons). Several factors were associated with shorter service life of ICD devices: CRT-D, occurrence of system failure and percentage of ventricular pacing. Our results confirmed significant differences among manufacturers. © The Authors. Journal of Cardiovascular Electrophysiology published by Wiley Periodicals, Inc.

Lacosamide Pharmacokinetics in a Critically Ill Patient Receiving Continuous Venovenous Hemofiltration.

PubMed

Franquiz, Miguel J; Kalaria, Shamir N; Armahizer, Michael J; Gopalakrishnan, Mathangi; McCarthy, Paul J; Badjatia, Neeraj

2018-02-01

Lacosamide is a new-generation antiepileptic drug (AED) that is eliminated by both hepatic and renal mechanisms. Lacosamide elimination by continuous renal replacement therapy (CRRT) has never been studied. The objective of this case report was to describe lacosamide pharmacokinetics in the setting of CRRT. We describe a single patient admitted to the study center with status epilepticus and multiorgan failure. The patient required both continuous venovenous hemofiltration (CVVH) and several AEDs. He was receiving intravenous lacosamide 200 mg twice/day at steady state prior to sampling. Plasma lacosamide concentrations were derived using a validated high-performance liquid chromatography method. Parameters were calculated using Phoenix WinNonlin 7.1 software. The peak concentration at steady state was 7.7 mg/L, the trough concentration was 5.9 mg/L (goal 5-12 mg/L). The volume of distribution was 0.7 L/kg, the elimination half-life was 21 hours, and the sieving coefficient was 0.8 (± 0.06). Lacosamide was cleared by CVVH as demonstrated by the sieving coefficient, but plasma concentrations remained within goal range throughout the dosing interval. These results may suggest that lacosamide 200 mg twice/day is a useful dosing strategy for critically ill patients who require CVVH. © 2017 Pharmacotherapy Publications, Inc.

The state of animal welfare in the context of refinement.

PubMed

Zurlo, Joanne; Hutchinson, Eric

2014-01-01

The ultimate goal of the Three Rs is the full replacement of animals used in biomedical research and testing. However, replacement is unlikely to occur in the near future; therefore the scientific community as a whole must continue to devote considerable effort to ensure optimal animal welfare for the benefit of the science and the animals, i.e., the R of refinement. Laws governing the care and use of laboratory animals have recently been revised in Europe and the US and these place greater emphasis on promoting the well-being of the animals in addition to minimizing pain and distress. Social housing for social species is now the default condition, which can present a challenge in certain experimental settings and for certain species. The practice of positive reinforcement training of laboratory animals, particularly non-human primates, is gathering momentum but is not yet universally employed. Enhanced consideration of refinement extends to rodents, particularly mice, whose use is still increasing as more genetically modified models are generated. The wastage of extraneous mice and the method of their euthanasia are refinement issues that still need to be addressed. An international, concerted effort into defining the needs of laboratory animals is still necessary to improve the quality of the animal models used as well as their welfare.

"Real life" longevity of implantable cardioverter-defibrillator devices.

PubMed

Manolis, Antonis S; Maounis, Themistoklis; Koulouris, Spyridon; Vassilikos, Vassilios

2017-09-01

Manufacturers of implantable cardioverter-defibrillators (ICDs) promise a 5- to 9-year projected longevity; however, real-life data indicate otherwise. The aim of the present study was to assess ICD longevity among 685 consecutive patients over the last 20 years. Real-life longevity of ICDs may differ from that stated by the manufacturers. The study included 601 men and 84 women (mean age, 63.1 ± 13.3 years). The underlying disease was coronary (n = 396) or valvular (n = 15) disease, cardiomyopathy (n = 220), or electrical disease (n = 54). The mean ejection fraction was 35%. Devices were implanted for secondary (n = 562) or primary (n = 123) prevention. Single- (n = 292) or dual-chamber (n = 269) or cardiac resynchronization therapy (CRT) devices (n = 124) were implanted in the abdomen (n = 17) or chest (n = 668). Over 20 years, ICD pulse generator replacements were performed in 238 patients (209 men; age 63.7 ± 13.9 years; ejection fraction, 37.7% ± 14.0%) who had an ICD for secondary (n = 210) or primary (n = 28) prevention. The mean ICD longevity was 58.3 ± 18.7 months. In 20 (8.4%) patients, devices exhibited premature battery depletion within 36 months. Most (94%) patients had none, minor, or modest use of ICD therapy. Longevity was longest for single-chamber devices and shortest for CRT devices. Latest-generation devices replaced over the second decade lasted longer compared with devices replaced during the first decade. When analyzed by manufacturer, Medtronic devices appeared to have longer longevity by 13 to 18 months. ICDs continue to have limited longevity of 4.9 ± 1.6 years, and 8% demonstrate premature battery depletion by 3 years. CRT devices have the shortest longevity (mean, 3.8 years) by 13 to 17 months, compared with other ICD devices. These findings have important implications, particularly in view of the high expense involved with this type of electrical therapy. © 2017 Wiley Periodicals, Inc.

Downscale climate change scenarios over the Western Himalayan region of India using multi-generation CMIP experiments

NASA Astrophysics Data System (ADS)

Das, Lalu; Meher, Jitendra K.; Akhter, Javed

2017-04-01

Assessing climate change information over the Western Himalayan Region (WHR) of India is crucial but challenging task due to its limited numbers of station data containing huge missing values. The issues of missing values of station data were replaced the Multiple Imputation Chained Equation (MICE) technique. Finally 22 numbers of rain gauge stations having continuous data during 1901-2005 and 16 numbers stations having continuous temperature data during 1969-2009 were considered as " reference stations for assessing rainfall and temperature trends in addition to evaluation of the GCMs available in the Coupled Model Intercomparison Project, Phase 3 (CMIP3) and phase 5 (CMIP5) over WRH. Station data indicates that the winter warming is higher and rapid (1.05oC) than other seasons and less warming in the post monsoon season in the last 41 years. Area averaged using 22 station data indicates that monsoon and winter rainfall has decreased by -5 mm and -320 mm during 1901-2000 while pre-monsoon and post monsoon showed an increasing trends of 21 mm and 13 mm respectively. Present study is constructed the downscaled climate change information at station locations (22 and 16 stations for rainfall and temperature respectively) over the WHR from the GCMs commonly available in the IPCC's different generations assessment reports namely 2nd, 3rd, 4th and 5th thereafter known as SAR, TAR, AR4 and AR5 respectively. Once the downscaled results are obtained for each generation model outputs, then a comparison of studies is carried out from the results of each generation. Finally an overall model improvement index (OMII) is developed using the downscaling results which is used to investigate the model improvement across generations as well as the improvement of downscaling results obtained from the empirical statistical downscaling (ESD) methods. In general, the results indicate that there is a gradual improvement of GCMs simulations as well as downscaling results across generation. Key words: MICE Techniques, CMIP3, CMIP5, ESD and OMII

Virtual local target method for avoiding local minimum in potential field based robot navigation.

PubMed

Zou, Xi-Yong; Zhu, Jing

2003-01-01

A novel robot navigation algorithm with global path generation capability is presented. Local minimum is a most intractable but is an encountered frequently problem in potential field based robot navigation. Through appointing appropriately some virtual local targets on the journey, it can be solved effectively. The key concept employed in this algorithm are the rules that govern when and how to appoint these virtual local targets. When the robot finds itself in danger of local minimum, a virtual local target is appointed to replace the global goal temporarily according to the rules. After the virtual target is reached, the robot continues on its journey by heading towards the global goal. The algorithm prevents the robot from running into local minima anymore. Simulation results showed that it is very effective in complex obstacle environments.

Messier: A Detailed NVM-Based DIMM Model for the SST Simulation Framework.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Awad, Amro; Voskuilen, Gwendolyn Renae; Rodrigues, Arun F.

2017-02-01

DRAM technology is the main building block of main memory, however, DRAM scaling is becoming very challenging. The main issues for DRAM scaling are the increasing error rates with each new generation, the geometric and physical constraints of scaling the capacitor part of the DRAM cells, and the high power consumption caused by the continuous need for refreshing cell values. At the same time, emerging Non- Volatile Memory (NVM) technologies, such as Phase-Change Memory (PCM), are emerging as promising replacements for DRAM. NVMs, when compared to current technologies e.g., NAND-based ash, have latencies comparable to DRAM. Additionally, NVMs are non-volatile,more » which eliminates the need for refresh power and enables persistent memory applications. Finally, NVMs have promising densities and the potential for multi-level cell (MLC) storage.« less

Fracture strength of flawed cylindrical pressure vessels under cryogenic temperatures

NASA Astrophysics Data System (ADS)

Christopher, T.; Sankarnarayanasamy, K.; Nageswara Rao, B.

2002-11-01

Damage tolerant and fail-safe approaches have been employed increasingly in the design of critical engineering components. In these approaches, one has to assess the residual strength of a component with an assumed pre-existing crack. In other cases, cracks may be detected during service. Then, there is a need to evaluate the residual strength of the cracked components in order to decide whether they can be continued safely or repair and replacement are imperative. A three-parameter fracture criterion is applied to correlate the fracture data on aluminium, titanium and steel materials from test results on cylindrical tanks/pressure vessels at cryogenic temperatures. Fracture parameters to generate the failure assessment diagram are determined for the materials considered in the present study. Failure pressure estimates were found to be in good agreement with test results.

System Study for Axial Vane Engine Technology

NASA Technical Reports Server (NTRS)

Badley, Patrick R.; Smith, Michael R.; Gould, Cedric O.

2008-01-01

The purpose of this engine feasibility study was to determine the benefits that can be achieved by incorporating positive displacement axial vane compression and expansion stages into high bypass turbofan engines. These positive-displacement stages would replace some or all of the conventional compressor and turbine stages in the turbine engine, but not the fan. The study considered combustion occurring internal to an axial vane component (i.e., Diesel engine replacing the standard turbine engine combustor, burner, and turbine); and external continuous flow combustion with an axial vane compressor and an axial vane turbine replacing conventional compressor and turbine systems.

Re-framing the representation of women in advertisements for hormone replacement therapy.

PubMed

Whittaker, R

1998-06-01

This article examines and presents examples of contemporary advertising within the medical and health professions that continue the process and organisation of knowledge about women and their reproductive bodies. It draws on feminist and poststructural perspectives to inform a critical evaluation of the visual representations of menopausal women and hormone replacement therapy. These representations work to construct certain definitions of the feminine that sustain and support existing contradictory cultural meanings and values about menopause. I argue that the images continue to misrepresent and define what forms of femininity and sexual gender are desirable and acceptable for menopausal women. The article addresses the problems of gender discrimination and bias within the advertising industry, and illustrates the ways in which readers of visual texts may be influenced by stereotypic assumptions concerning a woman's lived experience of menopause. It illustrates how specific symbolic images directed towards men and women for hormone replacement therapy, testosterone deficiency and sexual dysfunction influence the viewer's decision making and action responses.

Tetravalent chromium (Cr(4+)) as laser-active ion for tunable solid-state lasers

NASA Technical Reports Server (NTRS)

Seas, A.; Petricevic, V.; Alfano, Robert R.

1993-01-01

Major accomplishments under NASA grant NAG-1-1346 are summarized. (1) numerical modeling of the four mirror astigmatically compensated, Z-fold cavity was performed and several design parameters to be used for the construction of a femtosecond forsterite laser were revealed by simulation. (2) femtosecond pulses from a continuous wave mode-locked chromium doped forsterite laser were generated. The forsterite laser was actively mode-locked using an acousto-optic modulator operating at 78 MHz with two Brewster high dispersion glass prisms for intra-cavity chirp compensation. Transform-limited sub-100-fs pulses were routinely generated in the TEM(sub 00) mode with 85 mW of continuous power tunable over 1230-1280 nm. The shortest pulses of 60-fs pulsewidth were measured. (3) Self-mode-locked operation of the Cr:forsterite laser was achieved. Synchronous pumping was used to mode lock the forsterite laser resulting in picosecond pulses, which in turn provided the starting mechanism for self-mode-locking. The pulses generated had an FWHM of 105 fs and were tunable between 1230-1270 nm. (4) Numerical calculations indicated that the pair of SF 14 prisms used in the cavity compensated for quadratic phase but introduced a large cubic phase term. Further calculations of other optical glasses indicated that a pair of SFN 64 prisms can introduce the same amount of quadratic phase as SF 14 prisms but introduce a smaller cubic phase. When the SF 14 prisms were replaced by SFN 64 prisms the pulsewidth was reduced to 50 fs. Great improvement was observed in the stability of the self mode-locked forsterite laser and in the ease of achieving mode locking. Using the same experimental arrangement and a new forsterite crystal with improved FOM the pulse width was reduced to 36 fs.

EMT-Paramedic and EMT-Intermediate Continuing Education. National Guidelines.

ERIC Educational Resources Information Center

Brown, William E., Jr.; Dotterer, Robert W.; Gainor, Dia; Judd, Richard L.; Larmon, Baxter; Lewis, Kathryn M.; Margolis, Gregg S.; Mercer, Steve; Mistovich, Joseph J.; Newell, Lawrence D.; Politis, Jonathan F.; Stoy, Walt A.; Stupar, James A.; Walz, Bruce J.; Wagoner, Robert

This document, which replaces the 1985 national guidelines for emergency medical technician (EMT) continuing education (CE), presents guidelines for designing, implementing, and evaluating CE for EMTs. The introduction explains the process used to develop the revised guidelines. Section 1 discusses the following competency assurance principles…

40 CFR 94.211 - Emission-related maintenance instructions for purchasers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES..., replacement, or repair of the emission control devices and systems may be performed by any engine repair... and necessary to ensure the proper functioning of the engine's emission control systems. If the...

40 CFR 94.211 - Emission-related maintenance instructions for purchasers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES..., replacement, or repair of the emission control devices and systems may be performed by any engine repair... and necessary to ensure the proper functioning of the engine's emission control systems. If the...

40 CFR 94.211 - Emission-related maintenance instructions for purchasers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES..., replacement, or repair of the emission control devices and systems may be performed by any engine repair... and necessary to ensure the proper functioning of the engine's emission control systems. If the...

Modernization of the first-generation Intercosmos laser rangefinder at the Zvenigorod experimental satellite-tracking station of the Astronomical Council of the USSR Academy of Sciences

NASA Astrophysics Data System (ADS)

Matveev, D. T.; Chepurnov, B. D.

Test results obtained during 1980-1981 at the Zvenigorod station are presented for the Intercosmos laser rangefinder which was modified in various ways: e.g., optical components of the laser were replaced, and the mechanical Q-switch of the laser resonator was replaced by a phototropic Q-switch. Improved reliability was noted, and the ranging accuracy was increased by 1.5-2 times. It is concluded that the Zvenigorod tests indicate that the first-generation Intercosmos laser rangefinder can be effectively modernized at other Intercosmos tracking stations.

Managed care and critical pathway development: the joint replacement experience.

PubMed

Benham, A J

1999-01-01

This article examines the economic, social, ethical, and political issues affecting total joint replacement patients in a managed care environment. Using general systems theory as a framework, it examines the interrelated historical events that have shaped the development of both joint replacement procedures and managed care, and discusses the extent to which these two phenomena have been mutually influential. Specifically, the article examines the initial development, implementation, and continuing evolution of clinical pathways as an easily identified and relatively discrete manifestation of managed care for the joint replacement population. While the overall impact of managed care is beyond the scope of this presentation, it is hoped that a focus on the practical application of clinical pathways to joint replacement will allow some general principles to emerge that may be useful for both patients and practitioners operating in other aspects of the managed care environment.

Engineering and economic analysis for the utilization of geothermal fluids in a cane sugar processing plant. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Humme, J.T.; Tanaka, M.T.; Yokota, M.H.

1979-07-01

The purpose of this study was to determine the feasibility of geothermal resource utilization at the Puna Sugar Company cane sugar processing plant, located in Keaau, Hawaii. A proposed well site area was selected based on data from surface exploratory surveys. The liquid dominated well flow enters a binary thermal arrangement, which results in an acceptable quality steam for process use. Hydrogen sulfide in the well gases is incinerated, leaving sulfur dioxide in the waste gases. The sulfur dioxide in turn is recovered and used in the cane juice processing at the sugar factory. The clean geothermal steam from themore » binary system can be used directly for process requirements. It replaces steam generated by the firing of the waste fibrous product from cane sugar processing. The waste product, called bagasse, has a number of alternative uses, but an evaluation clearly indicated it should continue to be employed for steam generation. This steam, no longer required for process demands, can be directed to increased electric power generation. Revenues gained by the sale of this power to the utility, in addition to other savings developed through the utilization of geothermal energy, can offset the costs associated with hydrothermal utilization.« less

Printable thermoelectric devices and conductive patterns for medical applications

NASA Astrophysics Data System (ADS)

Lee, Jungmin; Kim, Hyunjung; Chen, Linfeng; Choi, Sang H.; Varadan, Vijay K.

2012-10-01

Remote point-of-care is expected to revolutionize the modern medical practice, and many efforts have been made for the development of wireless health monitoring systems for continuously detecting the physiological signals of patients. To make the remote point-of-care generally accepted and widely used, it is necessary to develop cost-effective and durable wireless health monitoring systems. Printing technique will be helpful for the fabrication of high-quality and low-cost medical devices and systems because it allows high-resolution and high-speed fabrication, low material consumption and nano-sized patterning on both flexible and rigid substrates. Furthermore, application of thermoelectric generators can replace conventional batteries as the power sources for wireless health monitoring systems because thermoelectric generators can convert the wasted heat or the heat from nature into electricity which is required for the operation of the wireless health monitoring systems. In this research, we propose the concept of printable thermoelectric devices and conductive patterns for the realization of more portable and cost-effective medical devices. To print thermoelectric generators and conductive patterns on substrates, printing inks with special characteristics should be developed. For the development of thermoelectric inks, nano-structured thermoelectric materials are synthesized and characterized; and for the development of conductive inks, two kinds of surface treated carbon nanotubes are used as active materials.

Characterization of a next-generation piezo bimorph X-ray mirror for synchrotron beamlines

PubMed Central

Alcock, Simon G.; Nistea, Ioana; Sutter, John P.; Sawhney, Kawal; Fermé, Jean-Jacques; Thellièr, Christophe; Peverini, Luca

2015-01-01

Piezo bimorph mirrors are versatile active optics used on many synchrotron beamlines. However, many bimorphs suffer from the ‘junction effect’: a periodic deformation of the optical surface which causes major aberrations to the reflected X-ray beam. This effect is linked to the construction of such mirrors, where piezo ceramics are glued directly below the thin optical substrate. In order to address this problem, a next-generation bimorph with piezos bonded to the side faces of a monolithic substrate was developed at Thales-SESO and optimized at Diamond Light Source. Using metrology feedback from the Diamond-NOM, the optical slope error was reduced to ∼0.5 µrad r.m.s. for a range of ellipses. To maximize usability, a novel holder was built to accommodate the substrate in any orientation. When replacing a first-generation bimorph on a synchrotron beamline, the new mirror significantly improved the size and shape of the reflected X-ray beam. Most importantly, there was no evidence of the junction effect even after eight months of continuous beamline usage. It is hoped that this new design will reinvigorate the use of active bimorph optics at synchrotron and free-electron laser facilities to manipulate and correct X-ray wavefronts. PMID:25537582

Characterization of a next-generation piezo bimorph X-ray mirror for synchrotron beamlines.

PubMed

Alcock, Simon G; Nistea, Ioana; Sutter, John P; Sawhney, Kawal; Fermé, Jean Jacques; Thellièr, Christophe; Peverini, Luca

2015-01-01

Piezo bimorph mirrors are versatile active optics used on many synchrotron beamlines. However, many bimorphs suffer from the `junction effect': a periodic deformation of the optical surface which causes major aberrations to the reflected X-ray beam. This effect is linked to the construction of such mirrors, where piezo ceramics are glued directly below the thin optical substrate. In order to address this problem, a next-generation bimorph with piezos bonded to the side faces of a monolithic substrate was developed at Thales-SESO and optimized at Diamond Light Source. Using metrology feedback from the Diamond-NOM, the optical slope error was reduced to ∼ 0.5 µrad r.m.s. for a range of ellipses. To maximize usability, a novel holder was built to accommodate the substrate in any orientation. When replacing a first-generation bimorph on a synchrotron beamline, the new mirror significantly improved the size and shape of the reflected X-ray beam. Most importantly, there was no evidence of the junction effect even after eight months of continuous beamline usage. It is hoped that this new design will reinvigorate the use of active bimorph optics at synchrotron and free-electron laser facilities to manipulate and correct X-ray wavefronts.

Analysis of correlation structures in the Synechocystis PCC6803 genome.

PubMed

Wu, Zuo-Bing

2014-12-01

Transfer of nucleotide strings in the Synechocystis sp. PCC6803 genome is investigated to exhibit periodic and non-periodic correlation structures by using the recurrence plot method and the phase space reconstruction technique. The periodic correlation structures are generated by periodic transfer of several substrings in long periodic or non-periodic nucleotide strings embedded in the coding regions of genes. The non-periodic correlation structures are generated by non-periodic transfer of several substrings covering or overlapping with the coding regions of genes. In the periodic and non-periodic transfer, some gaps divide the long nucleotide strings into the substrings and prevent their global transfer. Most of the gaps are either the replacement of one base or the insertion/reduction of one base. In the reconstructed phase space, the points generated from two or three steps for the continuous iterative transfer via the second maximal distance can be fitted by two lines. It partly reveals an intrinsic dynamics in the transfer of nucleotide strings. Due to the comparison of the relative positions and lengths, the substrings concerned with the non-periodic correlation structures are almost identical to the mobile elements annotated in the genome. The mobile elements are thus endowed with the basic results on the correlation structures. Copyright © 2014 Elsevier Ltd. All rights reserved.

High throughput generation and characterization of replication-competent clade C transmitter-founder simian human immunodeficiency viruses

PubMed Central

Dutta, Debashis; Johnson, Samuel; Dalal, Alisha; Deymier, Martin J.; Hunter, Eric

2018-01-01

Traditional restriction endonuclease-based cloning has been routinely used to generate replication-competent simian-human immunodeficiency viruses (SHIV) and simian tropic HIV (stHIV). This approach requires the existence of suitable restriction sites or the introduction of nucleotide changes to create them. Here, using an In-Fusion cloning technique that involves homologous recombination, we generated SHIVs and stHIVs based on epidemiologically linked clade C transmitted/founder HIV molecular clones from Zambia. Replacing vif from these HIV molecular clones with vif of SIVmac239 resulted in chimeric genomes used to generate infectious stHIV viruses. Likewise, exchanging HIV env genes and introducing N375 mutations to enhance macaque CD4 binding site and cloned into a SHIVAD8-EO backbone. The generated SHIVs and stHIV were infectious in TZMbl and ZB5 cells, as well as macaque PBMCs. Therefore, this method can replace traditional methods and be a valuable tool for the rapid generation and testing of molecular clones of stHIV and SHIV based on primary clinical isolates will be valuable to generate rapid novel challenge viruses for HIV vaccine/cure studies. PMID:29758076

Frequency and management of breakthrough bleeding with continuous use of the transvaginal contraceptive ring: a randomized controlled trial.

PubMed

Sulak, Patricia J; Smith, Virginia; Coffee, Andrea; Witt, Iris; Kuehl, Alicia L; Kuehl, Thomas J

2008-09-01

To assess bleeding patterns with continuous use of the transvaginal contraceptive ring. We did a prospective analysis of daily menstrual flow during a 21/7 cycle followed by 6 months of continuous use and institution of a randomized protocol to manage breakthrough bleeding/spotting. Seventy-four women completed the baseline 21/7 phase and were randomized equally into two groups during the continuous phase. Group 1 was instructed to replace the ring monthly on the same calendar day with no ring-free days. Group 2 was instructed to use the same process, but if breakthrough bleeding/spotting occurred for 5 days or more, they were to remove the ring for 4 days, store it, and then reinsert that ring. Sixty-five women completed the continuous phase with reduced average flow scores in the continuous phase compared with the 21/7 phase (P<.02). Most patients had no to minimal bleeding during continuous use, with group 2 experiencing a statistically greater percentage of days without breakthrough bleeding or spotting (95%) compared with group 1 (89%) (P=.016). Instituting a 4-day hormone-free interval was more (P<.001) effective in resolving breakthrough bleeding/spotting than continuing ring use. A reduction in bleeding occurred during continuous use with replacement of the transvaginal ring compared with baseline 21/7 use. Continuous vaginal ring use resulted in an acceptable bleeding profile in most patients, reduction in flow, reduction in pelvic pain, and a high continuation rate.

75 FR 42790 - Exelon Generation Company, LLC; Clinton Power Station; Environmental Assessment and Finding of No...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-22

... functions, and replace a Mechanical Maintenance person with a NLO. The regulation at 10 CFR 50.54(q) states... assigned other functions, and replace a Mechanical Maintenance person with a NLO. According to the licensee... to plant personnel work assignments. No changes will be made to plant buildings or the site property...

75 FR 5564 - Notice of a Project Waiver of Section 1605 (Buy American Requirement) of the American Recovery...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-03

... improvements will include a replacement of the existing belt filter press for sludge generated at the plant... project. The purchase of the new rotary sludge press is intended to replace the existing belt filter press... criteria: (1) Rotary press; (2) screw press; (3) centrifuge; and (4) belt filter press. Of the four...

Replacing a 252Cf source with a neutron generator in a shuffler - a conceptual design performed with MCNPX

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schear, Melissa A; Tobin, Stephen J

2009-01-01

The {sup 252}Cf shuffler has been widely used in nuclear safeguards and radioactive waste management to assay fissile isotopes, such as {sup 235}U or {sup 239}Pu, present in a variety of samples, ranging from small cans of uranium waste to metal samples weighing several kilograms. Like other non-destructive assay instruments, the shuffler uses an interrogating neutron source to induce fissions in the sample. Although shufflers with {sup 252}Cf sources have been reliably used for several decades, replacing this isotopic source with a neutron generator presents some distinct advantages. Neutron generators can be run in a continuous or pulsed mode, andmore » may be turned off, eliminating the need for shielding and a shuffling mechanism in the shuffler. There is also essentially no dose to personnel during installation, and no reliance on the availability of {sup 252}Cf. Despite these advantages, the more energetic neutrons emitted from the neutron generator (141 MeV for D-T generators) present some challenges for certain material types. For example when the enrichment of a uranium sample is unknown, the fission of {sup 238}U is generally undesirable. Since measuring uranium is one of the main uses of a shuffler, reducing the delayed neutron contribution from {sup 238}U is desirable. Hence, the shuffler hardware must be modified to accommodate a moderator configuration near the source to tailor the interrogating spectrum in a manner which promotes sub-threshold fissions (below 1 MeV) but avoids the over-moderation of the interrogating neutrons so as to avoid self-shielding. In this study, where there are many material and geometry combinations, the Monte Carlo N-Particle eXtended (MCNPX) transport code was used to model, design, and optimize the moderator configuration within the shuffler geometry. The code is then used to evaluate and compare the assay performances of both the modified shuffler and the current {sup 252}Cf shuffler designs for different test samples. The matrix effect and the non-uniformity of the interrogating flux are investigated and quantified in each case. The modified geometry proposed by this study can serve s a guide in retrofitting shufflers that are already in use.« less

Neck Pain One Week after Pacemaker Generator Replacement.

PubMed

Graham, Ross F; Wightman, John M

2015-07-01

The incidence of cardiac pacemaker implantation has risen markedly in the past three decades, making awareness of possible postprocedural complications critical to the emergency physician. This case is the first documented instance of internal jugular (IJ) deep vein thrombosis (DVT) from an uncomplicated pacemaker generator replacement. A patient presented to an Emergency Department with a 2-day history of mild left temporal headache migrating to his left neck. The patient did not volunteer this information, but review of systems revealed a temporary transvenous pacemaker inserted through the right IJ vein 1 week previously during a routine exchange of a left-sided cardiac pacemaker generator. Manipulation of the existing pacemaker wires entering the left subclavian vein was minimal. Computed tomographic angiography of the neck demonstrated near-complete thrombotic occlusion of the entire length of his left IJ vein. This required hospital admission for observation and treatment with anticoagulation. WHY SHOULD AN EMERGENCY PHYSICIAN BE AWARE OF THIS?: DVT, with thrombotic extension into adjacent vessels anywhere along the course of pacemaker wires, should be considered by the emergency provider in the evaluation of head, neck, or upper extremity symptoms after recent or remote implantation or manipulation of a transvenous cardiac pacemaker, including generator replacement. Failure to identify and treat appropriately could result in significant morbidity and mortality from airway edema, septic thrombophlebitis, superior vena cava syndrome, superior sagittal sinus thrombosis, or pulmonary embolism. Published by Elsevier Inc.

Zebra textures in carbonate rocks: Fractures produced by the force of crystallization during mineral replacement

NASA Astrophysics Data System (ADS)

Wallace, Malcolm W.; Hood, Ashleigh v. S.

2018-06-01

Zebra textures are enigmatic banded fabrics that occur in many carbonate-hosted ore deposits, dolomite hydrocarbon reservoirs and carbonate successions globally. They consist of a variety of minerals and are characterised by parallel light and dark bands that occur at a millimetre- to centimetre-scale. Based on petrological evidence, there is general consensus that the dark bands formed by replacement of the carbonate host rock. Historically, more contention surrounds the origin of the light bands, but the dominant view is that these are mineral-filled cavities, which is supported by overwhelming textural evidence. Overall, the feature common to all versions of zebra textures is mineral replacement of the original carbonate host. We suggest that mineral replacement (and the force of crystallization) in association with open space generation is a viable mechanism for the development of zebra cavity systems. Dissolution and open space generation in either evaporites or carbonates adjacent to the site of replacement reactions is necessary to remove the confining pressure from the rock and to allow the development of fractures. The pressure of the growing replacement crystals within the carbonate pervasively splits the carbonate apart, producing thin strips of carbonate surrounded by open space. The fractures may then be subject to dissolution and are later filled by cements. Very regular stratabound zebra textures (as found in ore deposits like Cadjebut, Australia and San Vicente, Peru) may be related to stratabound dissolution (of evaporites or carbonates), whereas irregularly distributed zebra textures are more likely to be associated with irregular carbonate dissolution.

Potential for Increasing the Output of Existing Hydroelectric Plants.

DTIC Science & Technology

1981-06-01

existing units to higher generating capacity by rehabilitating, modifying or replacing turbines and/or generators; increasing the effective...loss in converting fluid energy (flow and head) to mechanical energy ( turbine output) to electrical energy (generator output). The significant practical...opportunity is improvement of the energy conversion efficiency of the hydraulic turbine since the energy conversion efficiency of electrical

76 FR 6836 - Entergy Operations, Inc.; Notice of Withdrawal of Application for Amendment to Facility Operating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-08

.... NPF-38 for the Waterford Steam Electric Station, Unit 3, located in St. Charles Parish, Louisiana. In view of the originally planned steam generator (SG) replacement during the spring 2011 refueling outage... to TS 6.5.9, ``Steam Generator (SG) Program,'' and TS 6.9.1.5, ``Steam Generator Tube Inspection...

Do upslope impervious surfaces impact the run-on/runoff relationship?

USDA-ARS?s Scientific Manuscript database

Development of watersheds previously managed for agricultural uses for commercial and residential uses results in the replacement of pervious soil surfaces with impervious surfaces. Characteristics of runoff generated on new upslope impervious surfaces may differ from runoff generated on the predeve...

Twenty-five-year experience with the Björk-Shiley convexoconcave heart valve: a continuing clinical concern.

PubMed

Blot, William J; Ibrahim, Michel A; Ivey, Tom D; Acheson, Donald E; Brookmeyer, Ron; Weyman, Arthur; Defauw, Joseph; Smith, J Kermit; Harrison, Donald

2005-05-31

The first Björk-Shiley convexoconcave (BSCC) prosthetic heart valves were implanted in 1978. The 25th anniversary provided a stimulus to summarize the research data relevant to BSCC valve fracture, patient management, and current clinical options. Published and unpublished data on the risks of BSCC valve fracture and replacement were compiled, and strategies for identifying candidates for prophylactic valve reoperation were summarized. By December 2003, outlet strut fractures (OSFs), often with fatal outcomes, had been reported in 633 BSCC valves (0.7% of 86,000 valves implanted). Fractures still continue to occur, but average rates of OSFs in 60 degrees valves are now <0.1% per year. OSF risk varies markedly by valve characteristics, especially valve angle and size, with weaker effects associated with other manufacturing variables. OSF risks are mildly lower among women than men but decline sharply with advancing age. The risks of valve replacement typically greatly exceed those of OSF. By comparing individualized estimated risks of OSF versus valve replacement, guidelines have been developed to identify the small percentage of BSCC patients (mostly younger men) who would be expected to have a gain in life expectancy should reoperative surgery be performed. Twenty-five years after the initial BSCC valve implants, fractures continue to occur. Continued monitoring of BSCC patients is needed to track and quantify risks and enable periodic updating of guidelines for patients and their physicians.

39 CFR 777.24 - Replacement housing payments.

Code of Federal Regulations, 2014 CFR

2014-07-01

... displaced persons who lawfully and continuously owned and occupied a displacement dwelling for not less than... residential displaced persons who were tenants and lawfully and continuously occupied, a displacement dwelling... the sum of: (i) The amount which must be added to the acquisition cost of the displacement dwelling to...

39 CFR 777.24 - Replacement housing payments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... displaced persons who lawfully and continuously owned and occupied a displacement dwelling for not less than... residential displaced persons who were tenants and lawfully and continuously occupied, a displacement dwelling... the sum of: (i) The amount which must be added to the acquisition cost of the displacement dwelling to...

39 CFR 777.24 - Replacement housing payments.

Code of Federal Regulations, 2013 CFR

2013-07-01

... displaced persons who lawfully and continuously owned and occupied a displacement dwelling for not less than... residential displaced persons who were tenants and lawfully and continuously occupied, a displacement dwelling... the sum of: (i) The amount which must be added to the acquisition cost of the displacement dwelling to...

39 CFR 777.24 - Replacement housing payments.

Code of Federal Regulations, 2012 CFR

2012-07-01

... displaced persons who lawfully and continuously owned and occupied a displacement dwelling for not less than... residential displaced persons who were tenants and lawfully and continuously occupied, a displacement dwelling... the sum of: (i) The amount which must be added to the acquisition cost of the displacement dwelling to...

39 CFR 777.24 - Replacement housing payments.

Code of Federal Regulations, 2011 CFR

2011-07-01

... displaced persons who lawfully and continuously owned and occupied a displacement dwelling for not less than... residential displaced persons who were tenants and lawfully and continuously occupied, a displacement dwelling... the sum of: (i) The amount which must be added to the acquisition cost of the displacement dwelling to...

Preventing Continuous Renal Replacement Therapy-Induced Hypophosphatemia: An Extended Clinical Experience with a Phosphate-Containing Solution in the Setting of Regional Citrate Anticoagulation.

PubMed

Pistolesi, Valentina; Zeppilli, Laura; Polistena, Francesca; Sacco, Maria Itala; Pierucci, Alessandro; Tritapepe, Luigi; Regolisti, Giuseppe; Fiaccadori, Enrico; Morabito, Santo

2017-01-01

To evaluate the efficacy and safety of a commercially available phosphate-containing solution for continuous renal replacement therapy (CRRT) in preventing CRRT-related hypophosphatemia. In heart surgery patients undergoing continuous veno-venous haemodiafiltration (CVVHDF) with regional citrate anticoagulation (RCA), we combined an 18 mmol/l citrate solution with a phosphate-containing (1.2 mmol/l) dialysate/replacement fluid evaluating the incidence of hypophosphatemia and the need for parenteral phosphorus supplementation. In 75 patients on RCA-CVVHDF, the mean filter life was 53.9 ± 33.6 h. Regardless of baseline levels, phosphoremia was progressively corrected and maintained in a narrow normality range throughout RCA-CRRT days (after 72 h: 1.14 ± 0.25 mmol/l). Considering the whole CRRT period, 45 out of 975 (4.6%) serum phosphorus determinations met the criteria for mild (<0.81 mmol/l) or moderate (<0.61 mmol/l) hypophosphatemia; severe hypophosphatemia (<0.32 mmol/l) never occurred. After 72 h 88% of the patients were normophosphatemic, 9% hyperphosphatemic and 3% hypophosphatemic. RCA-CVVHDF with a phosphate-containing solution enabled the maintenance of phosphorus levels within normophosphatemic range in most of the patients, minimizing the occurrence of CRRT-related hypophosphatemia. © 2017 S. Karger AG, Basel.

Clinical Validation of Therapeutic Drug Monitoring of Imipenem in Spent Effluent in Critically Ill Patients Receiving Continuous Renal Replacement Therapy: A Pilot Study.

PubMed

Wen, Aiping; Li, Zhe; Yu, Junxian; Li, Ren; Cheng, Sheng; Duan, Meili; Bai, Jing

2016-01-01

The primary objective of this pilot study was to investigate whether the therapeutic drug monitoring of imipenem could be performed with spent effluent instead of blood sampling collected from critically ill patients under continuous renal replacement therapy. A prospective open-label study was conducted in a real clinical setting. Both blood and effluent samples were collected pairwise before imipenem administration and 0.5, 1, 1.5, 2, 3, 4, 6, and 8 h after imipenem administration. Plasma and effluent imipenem concentrations were determined by reversed-phase high-performance liquid chromatography with ultraviolet detection. Pharmacokinetic and pharmacodynamic parameters of blood and effluent samples were calculated. Eighty-three paired plasma and effluent samples were obtained from 10 patients. The Pearson correlation coefficient of the imipenem concentrations in plasma and effluent was 0.950 (P<0.0001). The average plasma-to-effluent imipenem concentration ratio was 1.044 (95% confidence interval, 0.975 to 1.114) with Bland-Altman analysis. No statistically significant difference was found in the pharmacokinetic and pharmacodynamic parameters tested in paired plasma and effluent samples with Wilcoxon test. Spent effluent of continuous renal replacement therapy could be used for therapeutic drug monitoring of imipenem instead of blood sampling in critically ill patients.

Steam generator feedwater nozzle transition piece replacement experience at Salem Unit 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patten, D.B.; Perrin, J.S.; Roberts, A.T.

Cracking of steam generator feedwater piping adjacent to the feedwater nozzles has been a recurring problem since 1979 at Salem Unit 1 owned and operated by Public Service Electric and Gas Company. In addition to the cracking problem, erosion-corrosion at the leading edge of the feedwater nozzle thermal sleeve was also observed in 1992. To provide a long-term solution for the pipe cracking and thermal sleeve erosion-corrosion problems, a unique transition piece forging was specially designed, fabricated, and installed for each of the four steam generators during the 1995 outage. This paper discusses the design, fabrication, and installation of themore » transition piece forgings at Salem Unit 1, and the experiences gained from this project. It is believed that these experiences may help other utilities when planning similar replacements in the future.« less

Twistact techno-economic analysis for wind turbine applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naughton, Brian Thomas; Koplow, Jeffrey P.; Vanness, Justin William

This report is the final deliverable for a techno-economic analysis of the Sandia National Laboratories-developed Twistact rotary electrical conductor. The U.S. Department of Energy Wind Energy Technologies Office supported a team of researchers at Sandia National Laboratories and the National Renewable Energy Laboratory to evaluate the potential of the Twistact technology to serve as a viable replacement to rare-earth materials used in permanent-magnet direct-drive wind turbine generators. This report compares three detailed generator models, two as baseline technologies and a third incorporating the Twistact technology. These models are then used to calculate the levelized cost of energy (LCOE) for threemore » comparable offshore wind plants using the three generator topologies. The National Renewable Energy Laboratorys techno-economic analysis indicates that Twistact technology can be used to design low-maintenance, brush-free, and wire-wound (instead of rare-earth-element (REE) permanent-magnet), direct-drive wind turbine generators without a significant change in LCOE and generation efficiency. Twistact technology acts as a hedge against sources of uncertain costs for direct-drive generators. On the one hand, for permanent-magnet direct-drive (PMDD) generators, the long-term price of REEs may increase due to increases in future demand, from electric vehicles and other technologies, whereas the supply remains limited and geographically concentrated. The potential higher prices in the future adversely affect the cost competitiveness of PMDD generators and may thwart industry investment in the development of the technology for wind turbine applications. Twistact technology can eliminate industry risk around the uncertainty of REE price and availability. Traditional wire-wound direct-drive generators experience reliability issues and higher maintenance costs because of the wear on the contact brushes necessary for field excitation. The brushes experience significant wear and require regular replacement over the lifetime of operation (on the order of a year or potentially less time). For offshore wind applications, the focus of this study, maintenance costs are higher than typical land-based systems due to the added time it often requires to access the site for repairs. Thus, eliminating the need for regular brush replacements reduces the uncertain costs and energy production losses associated with maintenance and replacement of contact brushes. Further, Twistact has a relatively negligible impact on LCOE but hedges risks associated with the current dominant designs for direct-drive generators for PMDD REE price volatility and wire-wound generator contact brush reliability. A final section looks at the overall supply chain of REEs considering the supply-side and demand-side drivers that encourage the risk of depending on these materials to support future deployment of not only wind energy but other industries as well.« less

Pulse Generator Exchange Does Not Accelerate the Rate of Electrical Failure in a Recalled Small Caliber ICD Lead.

PubMed

Lovelock, Joshua D; Premkumar, Ajay; Levy, Mathew R; Mengistu, Andenet; Hoskins, Michael H; El-Chami, Mikhael F; Lloyd, Michael S; Leon, Angel R; Langberg, Jonathan J; Delurgio, David B

2015-12-01

St. Jude Riata/Riata ST defibrillator leads (St. Jude Medical, Sylmar, CA, USA) were recalled by the Food and Drug Administration in 2011 for an increased rate of failure. More than 227,000 leads were implanted and at least 79,000 patients still have active Riata leads. Studies have examined clinical predictors of lead failure in Riata leads, but none have addressed the effect of implantable cardioverter defibrillator (ICD) generator exchange on lead failure. The purpose of this study is to assess the effect of ICD generator exchange on the rate of electrical failure in the Riata lead at 1 year. A retrospective chart review was conducted in patients who underwent implantation of a Riata/Riata ST lead at one center. Patients with a functioning Riata lead (with/without externalized conductor) at the time of ICD exchange were compared to controls with Riata leads implanted for a comparable amount of time who did not undergo generator replacement. Riata leads were implanted in 1,042 patients prior to the recall and 153 of these patients underwent generator exchange without lead replacement. Conductor externalization was noted in 21.5% of Riata leads in the ICD exchange cohort, which was not different from the control group (19.2%; P = 0.32). Two leads failed in the first year after generator replacement (1.5%) which did not significantly differ from the control group (2.0%; P = 0.57). At change-out, 54% received a commanded shock (18.6 ± 0.9 J) that did not result in any change in the high-voltage lead impedance (46.1 ± 1.1 ohms). Conductor externalization was seen frequently in our cohort of patients. ICD generator exchange did not accelerate the rate of Riata lead failure at 1 year. Although both the control and the change-out cohorts failed at a rate much greater than nonrecalled leads, generator exchange did not appear to add to the problem. ©2015 Wiley Periodicals, Inc.

Development of a Mandibular Motion Simulator for Total Joint Replacement

PubMed Central

Celebi, Nukhet; Rohner, E. Carlos; Gateno, Jaime; Noble, Philip C.; Ismaily, Sabir K.; Teichgraeber, John F.; Xia, James J.

2015-01-01

Purpose The purpose of this study was to develop a motion simulator capable of recreating and recording the full range of mandibular motions in a cadaveric preparation for an intact temporomandibular joint (TMJ) and after total joint replacement. Material and Methods A human cadaver head was used. Two sets of tracking balls were attached to the forehead and mandible, respectively. Computed tomographic (CT) scan was performed and 3-dimensional CT models of the skull were generated. The cadaver head was then dissected to attach the muscle activation cables and mounted onto the TMJ simulator. Realistic jaw motions were generated through the application of the following muscle forces: lateral pterygoid muscle, suprahyoid depressors (geniohyoid, mylohyoid, and digastric muscles), and elevator muscles. To simulate muscle contraction, cables were inserted into the mandible at the center area of each muscle's attachment. To provide a minimum mouth closing force at the initial position, the elevator muscles were combined at the anterior mandible. During mandibular movement, each motion was recorded using a high-resolution laser scanner. The right TMJ of the same head was reconstructed with a total TMJ prosthesis. The same forces were applied and the jaw motions were recorded again. CT scan was performed and 3-dimensional CT models of the skull with TMJ prosthesis were generated. Results Mandibular motions, before and after TMJ replacement, with and without lateral pterygoid muscle reattachment, were re-created in a cadaveric preparation. The laser-scanned data during the mandibular motion were used to drive 3-dimensional CT models. A movie for each mandibular motion was subsequently created for motion path analysis. Compared with mandibular motion before TMJ replacement, mandibular lateral and protrusive motions after TMJ replacement, with and without lateral pterygoid muscle reattachment, were greatly limited. The jaw motion recorded before total joint replacement was applied to the mandibular and prostheses models after total TMJ replacement. The condylar component was observed sinking into the fossa during jaw motion. Conclusion A motion simulator capable of re-creating and recording full range of mandibular motions in a cadaveric preparation has been developed. It can be used to simulate mandibular motions for the intact TMJ and total joint prosthesis, and to re-create and record their full range of mandibular motions. In addition, the full range of the recorded motion can be re-created as motion images in a computer. These images can be used for motion path analysis and to study the causation of limited range of motion after total joint replacement and strategies for improvement. PMID:21050636

Operational recovery of turbine No. 3 at Potomac Edison`s Dam No. 4 hydrogenerating facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pelczar, R.S.

1995-12-31

The Potomac Edison Dam No. 4 hydroelectric generating station is a historic, turn of the century facility located on the Potomac River near Shepherdstown, West Virginia. The station, originally constructed in 1909, employed twin horizontal Francis hydroturbine generating systems. The systems are unique in that the turbines and generators are offset 37 feet, interconnected by rope and sheaves. In May 1989 a third vertical open flume turbine generating system was added to make use of available site capacity. Both the turbine and speed increaser were the largest products developed by their respective manufacturers for a hydro turbine-generator application. This papermore » will review the subsequent operational experience which led to the original speed increaser failure on unit No. 3 and replacement of the drive system including special design considerations to the replacement speed increaser and its support structure. Specific design challenges included: (1) Designing and implementing a reliable configuration. (2) Reducing operational sound levels. (3) Minimizing harmful structure-borne vibrations which were affecting the internal rotating elements. (4) Incorporating a system brake for emergency and service purposes.« less

Strength Characteristics of Quarry Dust in Replacement of Sand

NASA Astrophysics Data System (ADS)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

Structure Property Relationships of Carboxylic Acid Isosteres.

PubMed

Lassalas, Pierrik; Gay, Bryant; Lasfargeas, Caroline; James, Michael J; Tran, Van; Vijayendran, Krishna G; Brunden, Kurt R; Kozlowski, Marisa C; Thomas, Craig J; Smith, Amos B; Huryn, Donna M; Ballatore, Carlo

2016-04-14

The replacement of a carboxylic acid with a surrogate structure, or (bio)-isostere, is a classical strategy in medicinal chemistry. The general underlying principle is that by maintaining the features of the carboxylic acid critical for biological activity, but appropriately modifying the physicochemical properties, improved analogs may result. In this context, a systematic assessment of the physicochemical properties of carboxylic acid isosteres would be desirable to enable more informed decisions of potential replacements to be used for analog design. Herein we report the structure-property relationships (SPR) of 35 phenylpropionic acid derivatives, in which the carboxylic acid moiety is replaced with a series of known isosteres. The data set generated provides an assessment of the relative impact on the physicochemical properties that these replacements may have compared to the carboxylic acid analog. As such, this study presents a framework for how to rationally apply isosteric replacements of the carboxylic acid functional group.

77 FR 49386 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-16

... prompted by reports of silicon particles inside the oxygen generator manifolds, which had chafed from the... the part number and serial number of each passenger oxygen container, replacing the oxygen generator manifold of the affected oxygen container with a serviceable manifold, and performing an operational check...

48 CFR 52.211-5 - Material Requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... materials and by-products generated from, and reused within, an original manufacturing process; provided... readjustments and material replacement. Recovered material means waste materials and by-products recovered or diverted from solid waste, but the term does not include those materials and by-products generated from...

Easi-CRISPR for creating knock-in and conditional knockout mouse models using long ssDNA donors.

PubMed

Miura, Hiromi; Quadros, Rolen M; Gurumurthy, Channabasavaiah B; Ohtsuka, Masato

2018-01-01

CRISPR/Cas9-based genome editing can easily generate knockout mouse models by disrupting the gene sequence, but its efficiency for creating models that require either insertion of exogenous DNA (knock-in) or replacement of genomic segments is very poor. The majority of mouse models used in research involve knock-in (reporters or recombinases) or gene replacement (e.g., conditional knockout alleles containing exons flanked by LoxP sites). A few methods for creating such models have been reported that use double-stranded DNA as donors, but their efficiency is typically 1-10% and therefore not suitable for routine use. We recently demonstrated that long single-stranded DNAs (ssDNAs) serve as very efficient donors, both for insertion and for gene replacement. We call this method efficient additions with ssDNA inserts-CRISPR (Easi-CRISPR) because it is a highly efficient technology (efficiency is typically 30-60% and reaches as high as 100% in some cases). The protocol takes ∼2 months to generate the founder mice.

Compliant mechanism road bicycle brake: a rigid-body replacement case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, Brian M; Howell, Larry L; Magleby, Spencer P

2011-01-19

The design of high-performance bicycle brakes is complicated by the competing design objectives of increased performance and low weight. But this challenge also provides a good case study to demonstrate the design of compliant mechanisms to replace current rigid-link mechanisms. This paper briefly reviews current road brake designs, demonstrates the use of rigid-body replacement synthesis to design a compliant mechanism, and illustrates the combination of compliant mechanism design tools. The resulting concept was generated from the modified dual-pivot brake design and is a partially compliant mechanism where one pin has the dual role of a joint and a mounting pin.more » The pseudo-rigid-body model, finite element analysis, and optimization algorithms are used to generate design dimensions, and designs are considered for both titanium and E-glass flexures. The resulting design has the potential of reducing the part count and overall weight while maintaining a performance similar to the benchmark.« less

Scandinavian Total Ankle Replacement: 15-Year Follow-up.

PubMed

Palanca, Ariel; Mann, Roger A; Mann, Jeffrey A; Haskell, Andrew

2018-02-01

Over the past decade, total ankle arthroplasty (TAA) has become a mainstay in the treatment of end-stage ankle arthritis. Currently in its fourth generation, the Scandanavian Total Ankle Replacement (STAR) is the only 3-piece mobile bearing ankle prosthesis available in the United States. Our current study reports implant survivorship at 15 years and patient outcomes for a subset of these survivors available for study. Eighty-four TAAs were performed between 1998 and 2000. Metal component survivorship at 15 years was calculated with a Kaplan-Meier curve. Twenty-four (29%) of 84 patients were available for participation with a minimum 15-year follow-up. Any radiographic changes were documented. All additional procedures and complications were recorded. Clinical findings, self-reported performance and pain evaluations, and AOFAS ankle/hindfoot scores were noted. Metal implant survival was 73% at 15 years. Of the 24 patients available for clinical evaluation, 18 of 24 patients (70.7%) had no change in prosthetic alignment from the immediate postoperative radiograph. Only 1 subtalar fusion was required for symptomatic adjacent joint arthritis. Three patients sustained a broken polyethylene component. AOFAS scores improved from an average of 39.6 points preoperatively, to an average of 71.6. More than half (52.4%) of patients with retained implants required an additional surgical procedure; 3 required 2 additional procedures. The average time to subsequent procedure was 10.2 years. Our small cohort demonstrated STAR ankles with retention at 9 years were highly likely to survive to 15 years, and patients continued to have significant improvement in pain relief and minimal decrease in function. At 15 years from TAA, metal survivorship was 73%. As with all ankle replacements, supplementary procedures were common. Level IV, case series.

The optimal hormonal replacement modality selection for multiple organ procurement from brain-dead organ donors

PubMed Central

Mi, Zhibao; Novitzky, Dimitri; Collins, Joseph F; Cooper, David KC

2015-01-01

The management of brain-dead organ donors is complex. The use of inotropic agents and replacement of depleted hormones (hormonal replacement therapy) is crucial for successful multiple organ procurement, yet the optimal hormonal replacement has not been identified, and the statistical adjustment to determine the best selection is not trivial. Traditional pair-wise comparisons between every pair of treatments, and multiple comparisons to all (MCA), are statistically conservative. Hsu’s multiple comparisons with the best (MCB) – adapted from the Dunnett’s multiple comparisons with control (MCC) – has been used for selecting the best treatment based on continuous variables. We selected the best hormonal replacement modality for successful multiple organ procurement using a two-step approach. First, we estimated the predicted margins by constructing generalized linear models (GLM) or generalized linear mixed models (GLMM), and then we applied the multiple comparison methods to identify the best hormonal replacement modality given that the testing of hormonal replacement modalities is independent. Based on 10-year data from the United Network for Organ Sharing (UNOS), among 16 hormonal replacement modalities, and using the 95% simultaneous confidence intervals, we found that the combination of thyroid hormone, a corticosteroid, antidiuretic hormone, and insulin was the best modality for multiple organ procurement for transplantation. PMID:25565890

Somatic hypermutation of the new antigen receptor gene (NAR) in the nurse shark does not generate the repertoire: possible role in antigen-driven reactions in the absence of germinal centers.

PubMed

Diaz, M; Greenberg, A S; Flajnik, M F

1998-11-24

The new antigen receptor (NAR) gene in the nurse shark diversifies extensively by somatic hypermutation. It is not known, however, whether NAR somatic hypermutation generates the primary repertoire (like in the sheep) or rather is used in antigen-driven immune responses. To address this issue, the sequences of NAR transmembrane (Tm) and secretory (Sec) forms, presumed to represent the primary and secondary repertoires, respectively, were examined from the peripheral blood lymphocytes of three adult nurse sharks. More than 40% of the Sec clones but fewer than 11% of Tm clones contained five mutations or more. Furthermore, more than 75% of the Tm clones had few or no mutations. Mutations in the Sec clones occurred mostly in the complementarity-determining regions (CDR) with a significant bias toward replacement substitutions in CDR1; in Tm clones there was no significant bias toward replacements and only a low level of targeting to the CDRs. Unlike the Tm clones where the replacement mutational pattern was similar to that seen for synonymous changes, Sec replacements displayed a distinct pattern of mutations. The types of mutations in NAR were similar to those found in mouse Ig genes rather than to the unusual pattern reported for shark and Xenopus Ig. Finally, an oligoclonal family of Sec clones revealed a striking trend toward acquisition of glutamic/aspartic acid, suggesting some degree of selection. These data strongly suggest that hypermutation of NAR does not generate the repertoire, but instead is involved in antigen-driven immune responses.

How do gait frequency and serum-replacement interval affect polyethylene wear in knee-wear simulator tests?

PubMed

Reinders, Jörn; Sonntag, Robert; Kretzer, Jan Philippe

2014-11-01

Polyethylene wear (PE) is known to be a limiting factor in total joint replacements. However, a standardized wear test (e.g. ISO standard) can only replicate the complex in vivo loading condition in a simplified form. In this study, two different parameters were analyzed: (a) Bovine serum, as a substitute for synovial fluid, is typically replaced every 500,000 cycles. However, a continuous regeneration takes place in vivo. How does serum-replacement interval affect the wear rate of total knee replacements? (b) Patients with an artificial joint show reduced gait frequencies compared to standardized testing. What is the influence of a reduced frequency? Three knee wear tests were run: (a) reference test (ISO), (b) testing with a shortened lubricant replacement interval, (c) testing with reduced frequency. The wear behavior was determined based on gravimetric measurements and wear particle analysis. The results showed that the reduced test frequency only had a small effect on wear behavior. Testing with 1 Hz frequency is therefore a valid method for wear testing. However, testing with a shortened replacement interval nearly doubled the wear rate. Wear particle analysis revealed only small differences in wear particle size between the different tests. Wear particles were not linearly released within one replacement interval. The ISO standard should be revised to address the marked effects of lubricant replacement interval on wear rate.

An innovative survey design to understand sustainable travel behaviors : potential of a rolling sample survey to replace traditional household travel surveys.

DOT National Transportation Integrated Search

2014-10-01

We propose an innovative survey with rolling samples to address a major fiscal challenge faced by many MPOs. Faced with a small, but : continuous budget, MPOs are increasingly unable to continue the current survey practice: conducting a large survey ...

75 FR 39787 - Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-13

... Limitations section (ALS) of the Instructions for Continued Airworthiness, replacing the upper bearing on... AD. (1) Within 60 days after the effective date of this AD: Revise the ALS of the Instructions for... days after the effective date of this AD: Revise the ALS of the Instructions for Continued...

The Persistence of Female Labor Supply: Empirical Evidence and Implications.

ERIC Educational Resources Information Center

Shaw, Kathryn

1994-01-01

Data from the Panel Study of Income Dynamics (1967-87) revealed little change in persistence of female labor supply because women have tended to become continuous workers, replacing continuous nonworkers. Periods of reduced hours are now less prolonged among older women. Employment patterns now appear to develop before marriage. (SK)

Computer-generated scenes depicting the HST capture and EVA repair mission

NASA Image and Video Library

1993-11-12

Computer generated scenes depicting the Hubble Space Telescope capture and a sequence of planned events on the planned extravehicular activity (EVA). Scenes include the Remote Manipulator System (RMS) arm assisting two astronauts changing out the Wide Field/Planetary Camera (WF/PC) (48699); RMS arm assisting in the temporary mating of the orbiting telescope to the flight support system in Endeavour's cargo bay (48700); Endeavour's RMS arm assisting in the "capture" of the orbiting telescope (48701); Two astronauts changing out the telescope's coprocessor (48702); RMS arm assistign two astronauts replacing one of the telescope's electronic control units (48703); RMS assisting two astronauts replacing the fuse plugs on the telescope's Power Distribution Unit (PDU) (48704); The telescope's High Resolution Spectrograph (HRS) kit is depicted in this scene (48705); Two astronauts during the removal of the high speed photometer and the installation of the COSTAR instrument (48706); Two astronauts, standing on the RMS, during installation of one of the Magnetic Sensing System (MSS) (48707); High angle view of the orbiting Space Shuttle Endeavour with its cargo bay doors open, revealing the bay's pre-capture configuration. Seen are, from the left, the Solar Array Carrier, the ORU Carrier and the flight support system (48708); Two astronauts performing the replacement of HST's Rate Sensor Units (RSU) (48709); The RMS arm assisting two astronauts with the replacement of the telescope's solar array panels (48710); Two astronauts replacing the telescope's Solar Array Drive Electronics (SADE) (48711).

Impact of treatment on Pb release from full and partially replaced harvested Lead Service Lines (LSLs).

PubMed

Cartier, Clément; Doré, Evelyne; Laroche, Laurent; Nour, Shokoufeh; Edwards, Marc; Prévost, Michèle

2013-02-01

Release of lead from 80% partially replaced service lines was compared to full lead service lines using harvested-stabilized lead pipes and field brass connectors. After more than a year of stabilization, lead release was consistent with field samples. Over the relatively short duration partial replacement of lead pipe by copper pipe (3 months), generated high lead release, attributed to galvanic corrosion, resulting in a final outcome for lead release that was even worse than for a full lead pipe. Increased lead release was especially evident at higher flow rates. Orthophosphate reduced lead release from full lead pipes by 64%. For partially replaced samples with copper, lead concentrations were unchanged by phosphate dosing at moderate flow (103 ± 265 vs 169 ± 349 μg/L) and were increased to very high levels when sampled at high flow rates (1001 ± 1808 vs 257 ± 224 μg/L). The increase lead release was in the form of particulate lead (>90%). In comparison to the condition without treatment, increased sulfate treatment had little impact on lead release from 100%-Pb rigs but reduced lead release from partially replaced lead pipes with copper. Our results also raise questions concerning protocols based on short 30 min stagnation (as those used in Canada) due to their incapacity to consider particulate lead release generated mostly after longer stagnation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Longevity of implantable cardioverter-defibrillators for cardiac resynchronization therapy in current clinical practice: an analysis according to influencing factors, device generation, and manufacturer.

PubMed

Landolina, Maurizio; Curnis, Antonio; Morani, Giovanni; Vado, Antonello; Ammendola, Ernesto; D'onofrio, Antonio; Stabile, Giuseppe; Crosato, Martino; Petracci, Barbara; Ceriotti, Carlo; Bontempi, Luca; Morosato, Martina; Ballari, Gian Paolo; Gasparini, Maurizio

2015-08-01

Device replacement at the time of battery depletion of implantable cardioverter-defibrillators (ICDs) may carry a considerable risk of complications and engenders costs for healthcare systems. Therefore, ICD device longevity is extremely important both from a clinical and economic standpoint. Cardiac resynchronization therapy defibrillators (CRT-D) battery longevity is shorter than ICDs. We determined the rate of replacements for battery depletion and we identified possible determinants of early depletion in a series of patients who had undergone implantation of CRT-D devices. We retrieved data on 1726 consecutive CRT-D systems implanted from January 2008 to March 2010 in nine centres. Five years after a successful CRT-D implantation procedure, 46% of devices were replaced due to battery depletion. The time to device replacement for battery depletion differed considerably among currently available CRT-D systems from different manufacturers, with rates of batteries still in service at 5 years ranging from 52 to 88% (log-rank test, P < 0.001). Left ventricular lead output and unipolar pacing configuration were independent determinants of early depletion [hazard ratio (HR): 1.96; 95% 95% confidence interval (CI): 1.57-2.46; P < 0.001 and HR: 1.58, 95% CI: 1.25-2.01; P < 0.001, respectively]. The implantation of a recent-generation device (HR: 0.57; 95% CI: 0.45-0.72; P < 0.001), the battery chemistry and the CRT-D manufacturer (HR: 0.64; 95% CI: 0.47-0.89; P = 0.008) were additional factors associated with replacement for battery depletion. The device longevity at 5 years was 54%. High left ventricular lead output and unipolar pacing configuration were associated with early battery depletion, while recent-generation CRT-Ds displayed better longevity. Significant differences emerged among currently available CRT-D systems from different manufacturers. © The Author 2015. Published by Oxford University Press on behalf of the European Society of Cardiology.

Association between mortality and replacement solution bicarbonate concentration in continuous renal replacement therapy: A propensity-matched cohort study.

PubMed

Kashani, Kianoush; Thongprayoon, Charat; Cheungpasitporn, Wisit; Iacovella, Gina M; Akhoundi, Abbasali; Albright, Robert C

2017-01-01

Given the known deleterious effects seen with bicarbonate supplementation for acidemia, we hypothesized that utilizing high bicarbonate concentration replacement solution in continuous venovenous hemofiltration (CVVH) would be independently associated with higher mortality. In a propensity score-matched historical cohort study conducted at a single tertiary care center from December 9, 2006, through December 31, 2009, a total of 287consecutive adult critically ill patients with Stage III acute kidney injury (AKI) requiring CVVH were enrolled. We excluded patients on maintenance dialysis, those who received other modalities of continuous renal replacement therapies, and patients that received a mixed of 22 and 32 mEq/L bicarbonate solution pre- and post-filter. The primary outcome was in-hospital and 90-day mortality rates. Among enrollees, 68 were used 32 mEq/L bicarbonate solution, and 219 received 22mEq/L bicarbonate solution for CVVH. Patients on 32 mEq/L bicarbonate solution were more often non-surgical, had lower pH and bicarbonate level but had higher blood potassium and phosphorus levels in comparison with those on 22 mEq/L bicarbonate solution. After adjustment for the baseline characteristics, the use of 32 bicarbonate solution was significantly associated with increased in-hospital (HR = 1.94; 95% CI 1.02-3.79) and 90-day mortality (HR = 1.50; 95% CI 1.03-2.14). There was a significant increase in the hospital (p = .03) and 90-day (p = .04) mortality between the 22 vs. 32 mEq/L bicarbonate solution groups following propensity matching. Our data showed there is a strong association between using high bicarbonate solution and mortality independent of severity of illness and comorbid conditions. These findings need to be evaluated further in prospective studies.

Effects of continuous vs. cycling estrogen replacement on the acquisition, retention and expression of place- and response-learning in the open-field tower maze.

PubMed

Lipatova, Olga; Byrd, Dennis; Green, John T; Toufexis, Donna J

2014-10-01

Estrogen has been shown to either enhance or impair learning and memory in female rats. The use of different experimental paradigms or estrogen treatment regimens may contribute to these disparate findings. In order to assess the effect of different estradiol (E2) treatments on several aspects of cognition, we trained ovariectomized female rats with either continuous, cycling, or vehicle E2 replacement, in an open-field tower maze task (OFTM) designed to test reference memory in a low-stress environment. In addition, in order to compare two distinct learning and memory systems, rats were trained to use either a dorsolateral striatum-based response type learning or a hippocampal-based place type learning to solve the maze. Results showed that cyclic, but not continuous, E2 replacement facilitated the acquisition of spatial memory in place-learners. Neither E2 regimen affected acquisition in response-learners. Additionally, when all experimental groups were performing at asymptote, rats were evaluated for performance stability by changing the location of their start position in the OFTM. Both regimens of E2 disrupted the expression of spatial memory in place-learners following the novel start position. However, E2 replacement protected ovariectomized female rats from the disruption of memory expression following a start position change in response-learners. Additionally all experimental groups performed equally well when tested following a 21-day period during which rats were absent from the maze. These results suggest that E2 fluctuation is particularly important in the acquisition of hippocampal-mediated spatial learning, and that hippocampal-based memory may be subject to disruption following environmental change, while striatum-based memory is subject to protection. Copyright © 2014 Elsevier Inc. All rights reserved.

Inconel 690 is alloy of choice for steam-generator tubing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strauss, S.D.

1996-02-01

The product of two decades of research and plant application, Inconel 690 promises superior long-term resistance to tube cracking in comparison to alloy 600. Ongoing steam-generator management techniques applied at nuclear pressurized-water-reactor (PWR) plants focus on tube monitoring, inspection, and repair, and on water-chemistry control. Of greatest concern to owner/operators of steam generators (SGs) with recirculating (U-bend) rather than straight through tubes is corrosion of several forms, including pitting, thinning, and cracking. As problems persist and operating and maintenance (O and M) costs become prohibitive, managers must consider the remaining option: complete or partial SG replacement. Although replacement costs canmore » range upward of $100-million, this step restores full-power operation, simplifies inspection, shortens subsequent outages, increases unit availability, and reduces radiation exposure of maintenance personnel. Taken together, these can lead to economies over the long term.« less

Evaluating the sustainability of an energy supply system using renewable energy sources: An energy demand assessment of South Carolina

NASA Astrophysics Data System (ADS)

Green, Cedric Fitzgerald

Sustainable energy is defined as a dynamic harmony between the equitable availability of energy-intensive goods and services to all people and the preservation of the earth for future generations. Sustainable energy development continues to be a major focus within the government and regulatory governing bodies in the electric utility industry. This is as a result of continued demand for electricity and the impact of greenhouse gas emissions from electricity generating plants on the environment by way of the greenhouse effect. A culmination of increasing concerns about climate change, the nuclear incident in Fukushima four years ago, and discussions on energy security in a world with growing energy demand have led to a movement for increasing the share of power generation from renewable energy sources. This work studies demand for electricity from primarily residential, commercial, agricultural, and industrial customers in South Carolina (SC) and its effect on the environment from coal-fired electricity generating plants. Moreover, this work studies sustainable renewable energy source-options based on the renewable resources available in the state of SC, as viable options to supplement generation from coal-fired electricity generating plants. In addition, greenhouse gas emissions and other pollutants from primarily coal-fired plants will be defined and quantified. Fundamental renewable energy source options will be defined and quantified based on availability and sustainability of SC's natural resources. This work studies the environmental, economic, and technical aspects of each renewable energy source as a sustainable energy option to replace power generation from coal-fired plants. Additionally, social aspect implications will be incorporated into each of the three aspects listed above, as these aspects are explored during the research and analysis. Electricity demand data and alternative energy source-supply data in SC are carried out and are used to develop and run the Sustainable Systems Analysis Algorithm (SSAA) and the multi-criteria decision analysis (MCDA) decision models. The following alternative energy sources for electricity (kilo- and megawatt output) will be assessed in this paper: solar, biomass and biofuels, hydro, geothermal, onshore wind, offshore wind, tidal, and natural gas. The SSAA methodology, in conjunction with the MCDA model techniques, will be used to obtain sustainable, alternative energy source system options; the system will attempt to balance its three linked aspects (environmental, economic, and technical). The results, based on the Sustainability Directive three-dimensional vector calculations from each alternative energy source option, are presented in this paper. Moving towards sustainability is a dynamically changing process, and the SSAA methodology is a synergist for system modifications that strives for continuous improvement toward the Ideal Sustainability Directive.

ON CONTINUOUS-REVIEW (S-1,S) INVENTORY POLICIES WITH STATE-DEPENDENT LEADTIMES,

DTIC Science & Technology

INVENTORY CONTROL, *REPLACEMENT THEORY), MATHEMATICAL MODELS, LEAD TIME , MANAGEMENT ENGINEERING, DISTRIBUTION FUNCTIONS, PROBABILITY, QUEUEING THEORY, COSTS, OPTIMIZATION, STATISTICAL PROCESSES, DIFFERENCE EQUATIONS

Chapter 7: Refrigerator Recycling Evaluation Protocol. The Uniform Methods Project: Methods for Determining Energy-Efficiency Savings for Specific Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurnik, Charles W.; Keeling, Josh; Bruchs, Doug

Refrigerator recycling programs are designed to save energy by removing operable, albeit less efficient, refrigerators from service. By offering free pickup, providing incentives, and disseminating information about the operating cost of less efficient refrigerators, these programs are designed to encourage consumers to: - Limit the use of secondary refrigerators -Relinquish refrigerators previously used as primary units when they are replaced (rather than keeping the existing refrigerator as a secondary unit) -Prevent the continued use of less efficient refrigerators in another household through a direct transfer (giving it away or selling it) or indirect transfer (resale on the used appliance market).more » Commonly implemented by third-party contractors (who collect and decommission participating appliances), these programs generate energy savings through the retirement of inefficient appliances. The decommissioning process captures environmentally harmful refrigerants and foam, and enables recycling of the plastic, metal, and wiring components.« less

Tension stimulation drives tissue formation in scaffold-free systems

NASA Astrophysics Data System (ADS)

Lee, Jennifer K.; Huwe, Le W.; Paschos, Nikolaos; Aryaei, Ashkan; Gegg, Courtney A.; Hu, Jerry C.; Athanasiou, Kyriacos A.

2017-08-01

Scaffold-free systems have emerged as viable approaches for engineering load-bearing tissues. However, the tensile properties of engineered tissues have remained far below the values for native tissue. Here, by using self-assembled articular cartilage as a model to examine the effects of intermittent and continuous tension stimulation on tissue formation, we show that the application of tension alone, or in combination with matrix remodelling and synthesis agents, leads to neocartilage with tensile properties approaching those of native tissue. Implantation of tension-stimulated tissues results in neotissues that are morphologically reminiscent of native cartilage. We also show that tension stimulation can be translated to a human cell source to generate anisotropic human neocartilage with enhanced tensile properties. Tension stimulation, which results in nearly sixfold improvements in tensile properties over unstimulated controls, may allow the engineering of mechanically robust biological replacements of native tissue.

A video event trigger for high frame rate, high resolution video technology

NASA Astrophysics Data System (ADS)

Williams, Glenn L.

1991-12-01

When video replaces film the digitized video data accumulates very rapidly, leading to a difficult and costly data storage problem. One solution exists for cases when the video images represent continuously repetitive 'static scenes' containing negligible activity, occasionally interrupted by short events of interest. Minutes or hours of redundant video frames can be ignored, and not stored, until activity begins. A new, highly parallel digital state machine generates a digital trigger signal at the onset of a video event. High capacity random access memory storage coupled with newly available fuzzy logic devices permits the monitoring of a video image stream for long term or short term changes caused by spatial translation, dilation, appearance, disappearance, or color change in a video object. Pretrigger and post-trigger storage techniques are then adaptable for archiving the digital stream from only the significant video images.

Electronics manufacturing and assembly in Japan

NASA Technical Reports Server (NTRS)

Kukowski, John A.; Boulton, William R.

1995-01-01

In the consumer electronics industry, precision processing technology is the basis for enhancing product functions and for minimizing components and end products. Throughout Japan, manufacturing technology is seen as critical to the production and assembly of advanced products. While its population has increased less than 30 percent over twenty-five years, Japan's gross national product has increase thirtyfold; this growth has resulted in large part from rapid replacement of manual operations with innovative, high-speed, large-scale, continuously running, complex machines that process a growing number of miniaturized components. The JTEC panel found that introduction of next-generation electronics products in Japan goes hand-in-hand with introduction of new and improved production equipment. In the panel's judgment, Japan's advanced process technologies and equipment development and its highly automated factories are crucial elements of its domination of the consumer electronics marketplace - and Japan's expertise in manufacturing consumer electronics products gives it potentially unapproachable process expertise in all electronics markets.

Do nonlinear dynamics in economics amount to a Kuhnian paradigm shift?

PubMed

Dore, Mohammed H I; Rosser, J Barkley

2007-01-01

Much empirical analysis and econometric work recognizes that there are nonlinearities, regime shifts or structural breaks, asymmetric adjustment costs, irreversibilities and lagged dependencies. Hence, empirical work has already transcended neoclassical economics. Some progress has also been made in modeling endogenously generated cyclical growth and fluctuations. All this is inconsistent with neoclassical general equilibrium. Hence there is growing evidence of Kuhnian anomalies. It therefore follows that there is a Kuhnian crisis in economics and further research in nonlinear dynamics and complexity can only increase the Kuhnian anomalies. This crisis can only deepen. However, there is an ideological commitment to general equilibrium that justifies "free enterprise" with only minimal state intervention that may still sustain neoclassical economics despite the growing evidence of Kuhnian anomalies. Thus, orthodox textbook theory continues to ignore this fact and static neoclassical theory remains a dogma with no apparent reformulation to replace it.

Membraneless water filtration using CO2

NASA Astrophysics Data System (ADS)

Shin, Sangwoo; Shardt, Orest; Warren, Patrick B.; Stone, Howard A.

2017-05-01

Water purification technologies such as microfiltration/ultrafiltration and reverse osmosis utilize porous membranes to remove suspended particles and solutes. These membranes, however, cause many drawbacks such as a high pumping cost and a need for periodic replacement due to fouling. Here we show an alternative membraneless method for separating suspended particles by exposing the colloidal suspension to CO2. Dissolution of CO2 into the suspension creates solute gradients that drive phoretic motion of particles. Due to the large diffusion potential generated by the dissociation of carbonic acid, colloidal particles move either away from or towards the gas-liquid interface depending on their surface charge. Using the directed motion of particles induced by exposure to CO2, we demonstrate a scalable, continuous flow, membraneless particle filtration process that exhibits low energy consumption, three orders of magnitude lower than conventional microfiltration/ultrafiltration processes, and is essentially free from fouling.

Membraneless water filtration using CO2

PubMed Central

Shin, Sangwoo; Shardt, Orest; Warren, Patrick B.; Stone, Howard A.

2017-01-01

Water purification technologies such as microfiltration/ultrafiltration and reverse osmosis utilize porous membranes to remove suspended particles and solutes. These membranes, however, cause many drawbacks such as a high pumping cost and a need for periodic replacement due to fouling. Here we show an alternative membraneless method for separating suspended particles by exposing the colloidal suspension to CO2. Dissolution of CO2 into the suspension creates solute gradients that drive phoretic motion of particles. Due to the large diffusion potential generated by the dissociation of carbonic acid, colloidal particles move either away from or towards the gas–liquid interface depending on their surface charge. Using the directed motion of particles induced by exposure to CO2, we demonstrate a scalable, continuous flow, membraneless particle filtration process that exhibits low energy consumption, three orders of magnitude lower than conventional microfiltration/ultrafiltration processes, and is essentially free from fouling. PMID:28462929

Space shuttle with common fuel tank for liquid rocket booster and main engines (supertanker space shuttle)

NASA Technical Reports Server (NTRS)

Thorpe, Douglas G.

1991-01-01

An operation and schedule enhancement is shown that replaces the four-body cluster (Space Shuttle Orbiter (SSO), external tank, and two solid rocket boosters) with a simpler two-body cluster (SSO and liquid rocket booster/external tank). At staging velocity, the booster unit (liquid-fueled booster engines and vehicle support structure) is jettisoned while the remaining SSO and supertank continues on to orbit. The simpler two-bodied cluster reduces the processing and stack time until SSO mate from 57 days (for the solid rocket booster) to 20 days (for the liquid rocket booster). The areas in which liquid booster systems are superior to solid rocket boosters are discussed. Alternative and future generation vehicles are reviewed to reveal greater performance and operations enhancements with more modifications to the current methods of propulsion design philosophy, e.g., combined cycle engines, and concentric propellant tanks.

Vacuum-assisted cell loading enables shear-free mammalian microfluidic culture

PubMed Central

Kolnik, Martin; Tsimring, Lev S; Hasty, Je

2012-01-01

Microfluidic perfusion cultures for mammalian cells provide a novel means for probing single-cell behavior but require the management of culture parameters such as flow-induced shear stress. Methods to eliminate shear stress generally focus on capturing cells in regions with high resistance to fluid flow. Here, we present a novel trapping design to easily and reliably load a high density of cells into culture chambers that are extremely isolated from potentially damaging flow effects. We utilize a transient on-chip vacuum to remove air from the culture chambers and rapidly replace the volume with a liquid cell suspension. We demonstrate the ability of this simple and robust method to load and culture three commonly used cell lines. We show how the incorporation of an on-chip function generator can be used for dynamic stimulation of cells during long-term continuous perfusion culture. PMID:22961584

Reduction of display artifacts by random sampling

NASA Technical Reports Server (NTRS)

Ahumada, A. J., Jr.; Nagel, D. C.; Watson, A. B.; Yellott, J. I., Jr.

1983-01-01

The application of random-sampling techniques to remove visible artifacts (such as flicker, moire patterns, and paradoxical motion) introduced in TV-type displays by discrete sequential scanning is discussed and demonstrated. Sequential-scanning artifacts are described; the window of visibility defined in spatiotemporal frequency space by Watson and Ahumada (1982 and 1983) and Watson et al. (1983) is explained; the basic principles of random sampling are reviewed and illustrated by the case of the human retina; and it is proposed that the sampling artifacts can be replaced by random noise, which can then be shifted to frequency-space regions outside the window of visibility. Vertical sequential, single-random-sequence, and continuously renewed random-sequence plotting displays generating 128 points at update rates up to 130 Hz are applied to images of stationary and moving lines, and best results are obtained with the single random sequence for the stationary lines and with the renewed random sequence for the moving lines.

A video event trigger for high frame rate, high resolution video technology

NASA Technical Reports Server (NTRS)

Williams, Glenn L.

1991-01-01

When video replaces film the digitized video data accumulates very rapidly, leading to a difficult and costly data storage problem. One solution exists for cases when the video images represent continuously repetitive 'static scenes' containing negligible activity, occasionally interrupted by short events of interest. Minutes or hours of redundant video frames can be ignored, and not stored, until activity begins. A new, highly parallel digital state machine generates a digital trigger signal at the onset of a video event. High capacity random access memory storage coupled with newly available fuzzy logic devices permits the monitoring of a video image stream for long term or short term changes caused by spatial translation, dilation, appearance, disappearance, or color change in a video object. Pretrigger and post-trigger storage techniques are then adaptable for archiving the digital stream from only the significant video images.

A Newly Defined and Xeno-Free Culture Medium Supports Every-Other-Day Medium Replacement in the Generation and Long-Term Cultivation of Human Pluripotent Stem Cells.

PubMed

Ahmadian Baghbaderani, Behnam; Tian, Xinghui; Scotty Cadet, Jean; Shah, Kevan; Walde, Amy; Tran, Huan; Kovarcik, Don Paul; Clarke, Diana; Fellner, Thomas

2016-01-01

Human pluripotent stem cells (hPSCs) present an unprecedented opportunity to advance human health by offering an alternative and renewable cell resource for cellular therapeutics and regenerative medicine. The present demand for high quality hPSCs for use in both research and clinical studies underscores the need to develop technologies that will simplify the cultivation process and control variability. Here we describe the development of a robust, defined and xeno-free hPSC medium that supports reliable propagation of hPSCs and generation of human induced pluripotent stem cells (hiPSCs) from multiple somatic cell types; long-term serial subculturing of hPSCs with every-other-day (EOD) medium replacement; and banking fully characterized hPSCs. The hPSCs cultured in this medium for over 40 passages are genetically stable, retain high expression levels of the pluripotency markers TRA-1-60, TRA-1-81, Oct-3/4 and SSEA-4, and readily differentiate into ectoderm, mesoderm and endoderm. Importantly, the medium plays an integral role in establishing a cGMP-compliant process for the manufacturing of hiPSCs that can be used for generation of clinically relevant cell types for cell replacement therapy applications.

VH Replacement Footprint Analyzer-I, a Java-Based Computer Program for Analyses of Immunoglobulin Heavy Chain Genes and Potential VH Replacement Products in Human and Mouse

PubMed Central

Huang, Lin; Lange, Miles D.; Zhang, Zhixin

2014-01-01

VH replacement occurs through RAG-mediated secondary recombination between a rearranged VH gene and an upstream unrearranged VH gene. Due to the location of the cryptic recombination signal sequence (cRSS, TACTGTG) at the 3′ end of VH gene coding region, a short stretch of nucleotides from the previous rearranged VH gene can be retained in the newly formed VH–DH junction as a “footprint” of VH replacement. Such footprints can be used as markers to identify Ig heavy chain (IgH) genes potentially generated through VH replacement. To explore the contribution of VH replacement products to the antibody repertoire, we developed a Java-based computer program, VH replacement footprint analyzer-I (VHRFA-I), to analyze published or newly obtained IgH genes from human or mouse. The VHRFA-1 program has multiple functional modules: it first uses service provided by the IMGT/V-QUEST program to assign potential VH, DH, and JH germline genes; then, it searches for VH replacement footprint motifs within the VH–DH junction (N1) regions of IgH gene sequences to identify potential VH replacement products; it can also analyze the frequencies of VH replacement products in correlation with publications, keywords, or VH, DH, and JH gene usages, and mutation status; it can further analyze the amino acid usages encoded by the identified VH replacement footprints. In summary, this program provides a useful computation tool for exploring the biological significance of VH replacement products in human and mouse. PMID:24575092

Incorporation of an aldehyde function in oligonucleotides.

PubMed

Tilquin, J M; Dechamps, M; Sonveaux, E

2001-01-01

A nucleotide-like phosphoramidite building block that has the nucleic base replaced by the tert-butyldimethylsilyl-protected styrene glycol was synthesized. After the automatic synthesis of an oligonucleotide incorporating this synthon, the benzaldehyde function was generated by fluoride deprotection and oxidation by sodium periodate. In a similar manner, an oligonucleotide where a nucleic base was replaced by the (CH2)8CH=O chain was synthesized and conjugated with biotin derivatives.

OGS Hydrogen Sensor ORU R&R

NASA Image and Video Library

2012-04-18

ISS030-E-236919 (18 April 2012) --- NASA astronaut Dan Burbank, Expedition 30 commander, works with the Oxygen Generator System (OGS) rack in the Tranquility node of the International Space Station. Burbank unpowered the OGS, purged the hydrogen sensor Orbital Replacement Unit (ORU) with the Hydrogen Sensor ORU Purge Adapter (HOPA) for return to Earth, and replaced the hydrogen sensor with a new spare, then cleaned the rack Avionics Air Assembly (AAA).

System and Methods to Generate Post-Swirl Propulsor Side Forces

DTIC Science & Technology

2012-09-11

Dkt . No. 101178 Application No. ?? REPLACEMENT SHEET? /2 12 2 16 4 10 14 14 2 2 Y Y F 14 24a 20 2a 6 X X 8 24 18 18a 26 28 22 FIG. 1...FIG. 2 1 Dkt . No. 101178 Application No. ?? REPLACEMENT SHEET? /22 0.00 -0.05 -0.10 -0.15 -0.20 -.0.25 -0.30 -0.35 -0.40

Brigham City Hydro Generation Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ammons, Tom B.

Brigham City owns and operates its own municipal power system which currently includes several hydroelectric facilities. This project was to update the efficiency and capacity of current hydro production due to increased water flow demands that could pass through existing generation facilities. During 2006-2012, this project completed efficiency evaluation as it related to its main objective by completing a feasibility study, undergoing necessary City Council approvals and required federal environmental reviews. As a result of Phase 1 of the project, a feasibility study was conducted to determine feasibility of hydro and solar portions of the original proposal. The results indicatedmore » that the existing Hydro plant which was constructed in the 1960’s was running at approximately 77% efficiency or less. Brigham City proposes that the efficiency calculations be refined to determine the economic feasibility of improving or replacing the existing equipment with new high efficiency equipment design specifically for the site. Brigham City completed the Feasibility Assessment of this project, and determined that the Upper Hydro that supplies the main culinary water to the city was feasible to continue with. Brigham City Council provided their approval of feasibility assessment’s results. The Upper Hydro Project include removal of the existing powerhouse equipment and controls and demolition of a section of concrete encased penstock, replacement of penstock just upstream of the turbine inlet, turbine bypass, turbine shut-off and bypass valves, turbine and generator package, control equipment, assembly, start-up, commissioning, Supervisory Control And Data Acquisition (SCADA), and the replacement of a section of conductors to the step-up transformer. Brigham City increased the existing 575 KW turbine and generator with an 825 KW turbine and generator. Following the results of the feasibility assessment Brigham City pursued required environmental reviews with the DOE and the U.S. Fish and Wildlife Services (USFWS) concurring with the National Environmental Policy Act of 1969 (NEPA) It was determined that Brigham City’s Upper Hydroelectric Power Plant upgrade would have no effect to federally listed or candidate species. However Brigham City has contributed a onetime lump sum towards Bonneville cutthroat trout conservation in the Northern Bonneville Geographic Management Unit with the intention to offset any impacts from the Upper Hydro Project needed to move forward with design and construction and is sufficient for NEPA compliance. No work was done in the river or river bank. During construction, the penstock was disconnected and water was diverted through and existing system around the powerhouse and back into the water system. The penstock, which is currently a 30-inch steel pipe, would be removed and replaced with a new section of 30-inch pipe. Brigham City worked with the DOE and was awarded a new modification and the permission to proceed with Phase III of our Hydro Project in Dec. 2013; with the exception to the modification of the award for the construction phase. Brigham City developed and issued a Request for Proposal for Engineer and Design vendor. Sunrise Engineering was selected for the Design and throughout the Construction Phase of the Upper Hydroelectric Power Plant. Brigham City conducted a Kickoff Meeting with Sunrise June 28, 2013 and received a Scope of Work Brigham City along with engineering firm sent out a RFP for Turbine, Generator and Equipment for Upper Hydro. We select Turbine/Generator Equipment from Canyon Industries located in Deming, WA. DOE awarded Brigham City a new modification and the permission to proceed with Phase III Construction of our Hydro Project. Brigham City Crews removed existing turbine/generator and old equipment alone with feeder wires coming into the building basically giving Caribou Construction an empty shell to begin demolition. Brigham City contracted with Caribou Construction from Jerome, Idaho for the Upper Power Plant construction. A kickoff meeting was June 24, 2014 and demolition was immediately started on building. Because of a delivery delay of Turbine, Generator and Equipment from Canyon Brigham City had to request another extension for the final date of completion. DOE awarded modification (.007) to Brigham City with a new completion date of August 1, 2015. The Turbine has had a few adjustments to help with efficiency; but the Generator had a slight vibration when generator got hot so Canyon Industries had U S Motor’s that manufactured the generator come to check out the issue. The other Equipment seems to be running normal. Brigham City, Sunrise Engineering and Canyon Industries met to determine what the vibration in the generator was and how to solve the issue Us Motor’s found some welds that failed: they have been repaired. U S Motor’s delivered the repaired generator Feb. 17, 2015. Canyon Industries arranged for a crane to installed generator in Power Plant. U S Motor’s balanced and wired generator. Plant Operators put the generator back on line. Canyon Industries returned and gave their approval to keep Hydro online. After Hydro was put back into operations it kept going off line because of overheating issues. Canyon Industries returned and replaced sensors and adjusted them to the proper settings for normal operations. Brigham City added additional steel screens to windows to increase air flow in Power Plant Building. After construction phase of the Upper Hydro Plant some landscaping has been restored around the building additional gravel brought in and leveled out and the road that was cut through for conduits to run wires. A retaining wall was installed to protect penstock. The Upper Hydro Plant is complete and in full operations. The final reimbursement was submitted.« less

Renewable Energy for the Next Generation

ERIC Educational Resources Information Center

Barton, Leslie

2005-01-01

Renewable energy is harnessed from natural and sustainable sources, like wind, sun and water. They offer a pollution-free, endless source of electricity that is crucial in the fight against climate change. Every unit of this "green" electricity directly replaces electricity normally generated from conventional polluting sources such as coal or…

BRIQUETTES FROM AGRICULTURAL RESIDUE AND OTHER WASTES FOR USE IN BIOMASS SYNGAS FUELED POWER GENERATION

EPA Science Inventory

The complete project will greatly increase the sustainability of small gasoline and/or diesel powered generators that are currently used to supplement or replace an unreliable power grid. This phase will develop the feedstock processing equipment needed to produce syngas bio-...

CINDA-3G: Improved Numerical Differencing Analyzer Program for Third-Generation Computers

NASA Technical Reports Server (NTRS)

Gaski, J. D.; Lewis, D. R.; Thompson, L. R.

1970-01-01

The goal of this work was to develop a new and versatile program to supplement or replace the original Chrysler Improved Numerical Differencing Analyzer (CINDA) thermal analyzer program in order to take advantage of the improved systems software and machine speeds of the third-generation computers.

The ciliary marginal zone of the zebrafish retina: clonal and time-lapse analysis of a continuously growing tissue.

PubMed

Wan, Yinan; Almeida, Alexandra D; Rulands, Steffen; Chalour, Naima; Muresan, Leila; Wu, Yunmin; Simons, Benjamin D; He, Jie; Harris, William A

2016-04-01

Clonal analysis is helping us understand the dynamics of cell replacement in homeostatic adult tissues (Simons and Clevers, 2011). Such an analysis, however, has not yet been achieved for continuously growing adult tissues, but is essential if we wish to understand the architecture of adult organs. The retinas of lower vertebrates grow throughout life from retinal stem cells (RSCs) and retinal progenitor cells (RPCs) at the rim of the retina, called the ciliary marginal zone (CMZ). Here, we show that RSCs reside in a niche at the extreme periphery of the CMZ and divide asymmetrically along a radial (peripheral to central) axis, leaving one daughter in the peripheral RSC niche and the other more central where it becomes an RPC. We also show that RPCs of the CMZ have clonal sizes and compositions that are statistically similar to progenitor cells of the embryonic retina and fit the same stochastic model of proliferation. These results link embryonic and postembryonic cell behaviour, and help to explain the constancy of tissue architecture that has been generated over a lifetime. © 2016. Published by The Company of Biologists Ltd.

Influence of renal function on mortality and ventricular arrhythmias in patients undergoing first implantable cardioverter-defibrillator generator replacement.

PubMed

Waks, Jonathan W; Higgins, Angela Y; Mittleman, Murray A; Buxton, Alfred E

2015-03-01

Impaired renal function is associated with increased mortality among patients with implantable cardioverter-defibrillators (ICDs). The relationship between renal function at time of ICD generator replacement and subsequent appropriate ICD therapies is not known. We identified 441 patients who underwent first ICD generator replacement between 2000 and 2011 and had serum creatinine measured within 30 days of their procedure. Patients were divided into tertiles based on estimated glomerular filtration rate (eGFR). Adjusted Cox proportional hazard and competing risk models were used to assess relationships between eGFR and subsequent mortality and appropriate ICD therapy. Median eGFR was 37.6, 59.3, and 84.8 mL/min/1.73 m(2) for tertiles 1-3, respectively. Five-year Kaplan-Meier survival probability was 34.8%, 61.4%, and 84.5% for tertiles 1-3, respectively (P < 0.001). After multivariable adjustment, compared to tertile 3, worse eGFR tertile was associated with increased mortality (HR 2.84, 95% CI [1.36-5.94] for tertile 2; HR 3.84, 95% CI [1.81-8.12] for tertile 1). At 5 years, 57.0%, 58.1%, and 60.2% of patients remained free of appropriate ICD therapy in tertiles 1-3, respectively (P = 0.82). After adjustment, eGFR tertile was not associated with future appropriate ICD therapy. Results were unchanged in an adjusted competing risk model accounting for death. At time of first ICD generator replacement, lower eGFR is associated with higher mortality, but not with appropriate ICD therapies. The poorer survival of ICD patients with reduced eGFR does not appear to be influenced by arrhythmia status, and there is no clear proarrhythmic effect of renal dysfunction, even after accounting for the competing risk of death. © 2014 Wiley Periodicals, Inc.

Report on the National Eye Institute Audacious Goals Initiative: Replacement of Retinal Ganglion Cells from Endogenous Cell Sources.

PubMed

Vetter, Monica L; Hitchcock, Peter F

2017-03-01

This report emerges from a workshop convened by the National Eye Institute (NEI) as part of the "Audacious Goals Initiative" (AGI). The workshop addressed the replacement of retinal ganglion cells (RGCs) from exogenous and endogenous sources, and sought to identify the gaps in our knowledge and barriers to progress in devising cellular replacement therapies for diseases where RGCs die. Here, we briefly review relevant literature regarding common diseases associated with RGC death, the genesis of RGCs in vivo, strategies for generating transplantable RGCs in vitro, and potential endogenous cellular sources to regenerate these cells. These topics provided the clinical and scientific context for the discussion among the workshop participants and are relevant to efforts that may lead to therapeutic approaches for replacing RGCs. This report also summarizes the content of the workshop discussion, which focused on: (1) cell sources for RGC replacement and regeneration, (2) optimizing integration, survival, and synaptogenesis of new RGCs, and (3) approaches for assessing the outcomes of RGC replacement therapies. We conclude this report with a summary of recommendations, based on the workshop discussions, which may guide vision scientists seeking to develop therapies for replacing RGCs in humans.

Fractional dynamics of globally slow transcription and its impact on deterministic genetic oscillation.

PubMed

Wei, Kun; Gao, Shilong; Zhong, Suchuan; Ma, Hong

2012-01-01

In dynamical systems theory, a system which can be described by differential equations is called a continuous dynamical system. In studies on genetic oscillation, most deterministic models at early stage are usually built on ordinary differential equations (ODE). Therefore, gene transcription which is a vital part in genetic oscillation is presupposed to be a continuous dynamical system by default. However, recent studies argued that discontinuous transcription might be more common than continuous transcription. In this paper, by appending the inserted silent interval lying between two neighboring transcriptional events to the end of the preceding event, we established that the running time for an intact transcriptional event increases and gene transcription thus shows slow dynamics. By globally replacing the original time increment for each state increment by a larger one, we introduced fractional differential equations (FDE) to describe such globally slow transcription. The impact of fractionization on genetic oscillation was then studied in two early stage models--the Goodwin oscillator and the Rössler oscillator. By constructing a "dual memory" oscillator--the fractional delay Goodwin oscillator, we suggested that four general requirements for generating genetic oscillation should be revised to be negative feedback, sufficient nonlinearity, sufficient memory and proper balancing of timescale. The numerical study of the fractional Rössler oscillator implied that the globally slow transcription tends to lower the chance of a coupled or more complex nonlinear genetic oscillatory system behaving chaotically.

Properties of Cement Mortar Produced from Mixed Waste Materials with Pozzolanic Characteristics.

PubMed

Yen, Chi-Liang; Tseng, Dyi-Hwa; Wu, Yue-Ze

2012-07-01

Waste materials with pozzolanic characteristics, such as sewage sludge ash (SSA), coal combustion fly ash (FA), and granulated blast furnace slag (GBS), were reused as partial cement replacements for making cement mortar in this study. Experimental results revealed that with dual replacement of cement by SSA and GBS and triple replacement by SSA, FA, and GBS at 50% of total cement replacement, the compressive strength (Sc) of the blended cement mortars at 56 days was 93.7% and 92.9% of the control cement mortar, respectively. GBS had the highest strength activity index value and could produce large amounts of CaO to enhance the pozzolanic activity of SSA/FA and form calcium silicate hydrate gels to fill the capillary pores of the cement mortar. Consequently, the Sc development of cement mortar with GBS replacement was better than that without GBS, and the total pore volume of blended cement mortars with GBS/SSA replacement was less than that with FA/SSA replacement. In the cement mortar with modified SSA and GBS at 70% of total cement replacement, the Sc at 56 days was 92.4% of the control mortar. Modifying the content of calcium in SSA also increased its pozzolanic reaction. CaCl(2) accelerated the pozzolanic activity of SSA better than lime did. Moreover, blending cement mortars with GBS/SSA replacement could generate more monosulfoaluminate to fill capillary pores.

Properties of Cement Mortar Produced from Mixed Waste Materials with Pozzolanic Characteristics

PubMed Central

Yen, Chi-Liang; Tseng, Dyi-Hwa; Wu, Yue-Ze

2012-01-01

Abstract Waste materials with pozzolanic characteristics, such as sewage sludge ash (SSA), coal combustion fly ash (FA), and granulated blast furnace slag (GBS), were reused as partial cement replacements for making cement mortar in this study. Experimental results revealed that with dual replacement of cement by SSA and GBS and triple replacement by SSA, FA, and GBS at 50% of total cement replacement, the compressive strength (Sc) of the blended cement mortars at 56 days was 93.7% and 92.9% of the control cement mortar, respectively. GBS had the highest strength activity index value and could produce large amounts of CaO to enhance the pozzolanic activity of SSA/FA and form calcium silicate hydrate gels to fill the capillary pores of the cement mortar. Consequently, the Sc development of cement mortar with GBS replacement was better than that without GBS, and the total pore volume of blended cement mortars with GBS/SSA replacement was less than that with FA/SSA replacement. In the cement mortar with modified SSA and GBS at 70% of total cement replacement, the Sc at 56 days was 92.4% of the control mortar. Modifying the content of calcium in SSA also increased its pozzolanic reaction. CaCl2 accelerated the pozzolanic activity of SSA better than lime did. Moreover, blending cement mortars with GBS/SSA replacement could generate more monosulfoaluminate to fill capillary pores. PMID:22783062

[Assisted peritoneal dialysis: home-based renal replacement therapy for the elderly patient].

PubMed

Wiesholzer, Martin

2013-06-01

The number of elderly patients with end stage renal disease is constantly increasing. Conventional hämodiaylsis as the mainstay of renal replacement therapy is often poorly tolerated by frail eldery patients with multiple comorbidities. Although many of these patients would prefer a home based dialysis treatment, the number of elderly patients using peritoneal dialysis (PD) is still low. Impaired physical and cognitive function often generates insurmountable barriers for self care peritoneal dialysis. Assisted peritoneal dialysis can overcome many of these barriers and give elderly patients the ability of a renal replacement therapy in their own homes respecting their needs.

Long-Term Adaptive Servo-Ventilator Treatment Prevents Cardiac Death and Improves Clinical Outcome.

PubMed

Imamura, Teruhiko; Kinugawa, Koichiro; Nitta, Daisuke; Komuro, Issei

2016-01-01

Adaptive servo-ventilation (ASV) is a recently developed, noninvasive therapeutic tool for the treatment of heart failure (HF). However, the efficacy of ASV therapy in patients with advanced HF remains uncertain, especially as regards its contribution to freedom from cardiac replacement therapy. A total of 85 patients with advanced HF (New York Heart Association [NYHA] class IV 71%, inotrope infusion-dependent 34%) refractory to guideline-directed medical therapy, received ASV therapy, irrespective of sleep-disordered breathing, at our institute between 2008 and 2014. Among these 85 patients, 46 continued ASV therapy for > 1 month (continued group), whereas 39 discontinued the therapy after < 1 month because of intolerance (discontinued group). There were no significant differences in baseline variables between the two groups. Heart rate indicating sympathetic activity, left ventricular (LV) reverse remodeling assessed by LV diastolic diameter, LV ejection fraction, and the grades of mitral and tricuspid regurgitations, HF severity assessed by NYHA class and plasma level of B-type natriuretic peptide, and end-organ dysfunction, improved significantly at 6 months following the initiation of ASV therapy (P < 0.05 for all). All-cause mortality and cardiac death rate were significantly lower during 2-year follow up in the continued group (P < 0.05 for both). In conclusion, ASV is a novel therapeutic tool prior to cardiac replacement therapy in patients with advanced HF and may prolong the period until cardiac replacement therapy becomes necessary.

Clinical Validation of Therapeutic Drug Monitoring of Imipenem in Spent Effluent in Critically Ill Patients Receiving Continuous Renal Replacement Therapy: A Pilot Study

PubMed Central

Wen, Aiping; Li, Zhe; Yu, Junxian; Li, Ren; Cheng, Sheng; Duan, Meili; Bai, Jing

2016-01-01

Objectives The primary objective of this pilot study was to investigate whether the therapeutic drug monitoring of imipenem could be performed with spent effluent instead of blood sampling collected from critically ill patients under continuous renal replacement therapy. Methods A prospective open-label study was conducted in a real clinical setting. Both blood and effluent samples were collected pairwise before imipenem administration and 0.5, 1, 1.5, 2, 3, 4, 6, and 8 h after imipenem administration. Plasma and effluent imipenem concentrations were determined by reversed-phase high-performance liquid chromatography with ultraviolet detection. Pharmacokinetic and pharmacodynamic parameters of blood and effluent samples were calculated. Results Eighty-three paired plasma and effluent samples were obtained from 10 patients. The Pearson correlation coefficient of the imipenem concentrations in plasma and effluent was 0.950 (P<0.0001). The average plasma-to-effluent imipenem concentration ratio was 1.044 (95% confidence interval, 0.975 to 1.114) with Bland-Altman analysis. No statistically significant difference was found in the pharmacokinetic and pharmacodynamic parameters tested in paired plasma and effluent samples with Wilcoxon test. Conclusion Spent effluent of continuous renal replacement therapy could be used for therapeutic drug monitoring of imipenem instead of blood sampling in critically ill patients. PMID:27093294

Implications of Outside-the-Box Technologies on Future Space Exploration and Colonization

NASA Astrophysics Data System (ADS)

Loder, Theodore C.

2003-01-01

In general, planning for future manned space exploration either to the moon, Mars, or an asteroid has depended on a somewhat linear extrapolation of our present technologies. Two major prohibitive cost issues regarding such planning are payload lift and in-flight energy generation. The costs of these in both engineering and actual flight costs, coupled with the planning necessary to carry out such exploration have prevented us from actively moving forward. Although, it will be worthwhile to continue to plan for such exploration using ``present'' technologies, I recommend that planning be concerned mainly with mission strategies and goals utilizing both present technology and totally new energy breakthroughs. There are presently in research and development an entire suite of relevant outside-the-box technologies which will include both zero point energy generation and antigravity technologies that will replace our present solar/nuclear/fuel cell energy technologies and liquid/solid fuel rockets. This paper describes some of these technologies, the physics behind them and their potential use for manned space exploration. The companies and countries that first incorporate these technologies into their space programs will lead the way in exploring and colonizing space.

Commercial grade item (CGI) dedication of generators for nuclear safety related applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, R.K.; Hajos, L.G.

1993-03-01

The number of nuclear safety related equipment suppliers and the availability of spare and replacement parts designed specifically for nuclear safety related application are shrinking rapidly. These have made it necessary for utilities to apply commercial grade spare and replacement parts in nuclear safety related applications after implementing proper acceptance and dedication process to verify that such items conform with the requirements of their use in nuclear safety related application. The general guidelines for the commercial grade item (CGI) acceptance and dedication are provided in US Nuclear Regulatory Commission (NRC) Generic Letters and Electric Power Research Institute (EPRI) Report NP-5652,more » Guideline for the Utilization of Commercial Grade Items in Nuclear Safety Related Applications. This paper presents an application of these generic guidelines for procurement, acceptance, and dedication of a commercial grade generator for use as a standby generator at Salem Generating Station Units 1 and 2. The paper identifies the critical characteristics of the generator which once verified, will provide reasonable assurance that the generator will perform its intended safety function. The paper also delineates the method of verification of the critical characteristics through tests and provide acceptance criteria for the test results. The methodology presented in this paper may be used as specific guidelines for reliable and cost effective procurement and dedication of commercial grade generators for use as standby generators at nuclear power plants.« less

Adult subventricular zone neural stem cells as a potential source of dopaminergic replacement neurons

PubMed Central

Cave, John W.; Wang, Meng; Baker, Harriet

2014-01-01

Clinical trials engrafting human fetal ventral mesencephalic tissue have demonstrated, in principle, that cell replacement therapy provides substantial long-lasting improvement of motor impairments generated by Parkinson's Disease (PD). The use of fetal tissue is not practical for widespread clinical implementation of this therapy, but stem cells are a promising alternative source for obtaining replacement cells. The ideal stem cell source has yet to be established and, in this review, we discuss the potential of neural stem cells in the adult subventricular zone (SVZ) as an autologous source of replacement cells. We identify three key challenges for further developing this potential source of replacement cells: (1) improving survival of transplanted cells, (2) suppressing glial progenitor proliferation and survival, and (3) developing methods to efficiently produce dopaminergic neurons. Subventricular neural stem cells naturally produce a dopaminergic interneuron phenotype that has an apparent lack of vulnerability to PD-mediated degeneration. We also discuss whether olfactory bulb dopaminergic neurons derived from adult SVZ neural stem cells are a suitable source for cell replacement strategies. PMID:24574954

Reliability of hybrid photovoltaic DC micro-grid systems for emergency shelters and other applications

NASA Astrophysics Data System (ADS)

Dhere, Neelkanth G.; Schleith, Susan

2014-10-01

Improvement of energy efficiency in the SunSmart Schools Emergency Shelters requires new methods for optimizing the energy consumption within the shelters. One major limitation in current systems is the requirement of converting direct current (DC) power generated from the PV array into alternating current (AC) power which is distributed throughout the shelters. Oftentimes, this AC power is then converted back to DC to run certain appliances throughout the shelters resulting in a significant waste of energy due to DC to AC and then again AC to DC conversion. This paper seeks to extract the maximum value out of PV systems by directly powering essential load components within the shelters that already run on DC power without the use of an inverter and above all to make the system reliable and durable. Furthermore, additional DC applications such as LED lighting, televisions, computers and fans operated with DC brushless motors will be installed as replacements to traditional devices in order to improve efficiency and reduce energy consumption. Cost of energy storage technologies continue to decline as new technologies scale up and new incentives are put in place. This will provide a cost effective way to stabilize the energy generation of a PV system as well as to provide continuous energy during night hours. It is planned to develop a pilot program of an integrated system that can provide uninterrupted DC power to essential base load appliances (heating, cooling, lighting, etc.) at the Florida Solar Energy Center (FSEC) command center for disaster management. PV arrays are proposed to be installed on energy efficient test houses at FSEC as well as at private homes having PV arrays where the owners volunteer to participate in the program. It is also planned to monitor the performance of the PV arrays and functioning of the appliances with the aim to improve their reliability and durability. After a successful demonstration of the hybrid DC microgrid based emergency shelter together with the monitoring system, it is planned to replicate it at other schools in Florida and elsewhere to provide continuous power for essential applications, maximizing the value of PV generation systems.

Inactivation of the indole-diterpene biosynthetic gene cluster of Claviceps paspali by Agrobacterium-mediated gene replacement.

PubMed

Kozák, László; Szilágyi, Zoltán; Vágó, Barbara; Kakuk, Annamária; Tóth, László; Molnár, István; Pócsi, István

2018-04-01

The hypocrealean fungus Claviceps paspali is a parasite of wild grasses. This fungus is widely utilized in the pharmaceutical industry for the manufacture of ergot alkaloids, but also produces tremorgenic and neurotoxic indole-diterpene (IDT) secondary metabolites such as paspalitrems A and B. IDTs cause significant losses in agriculture and represent health hazards that threaten food security. Conversely, IDTs may also be utilized as lead compounds for pharmaceutical drug discovery. Current protoplast-mediated transformation protocols of C. paspali are inadequate as they suffer from inefficiencies in protoplast regeneration, a low frequency of DNA integration, and a low mitotic stability of the nascent transformants. We adapted and optimized Agrobacterium tumefaciens-mediated transformation (ATMT) for C. paspali and validated this method with the straightforward creation of a mutant strain of this fungus featuring a targeted replacement of key genes in the putative IDT biosynthetic gene cluster. Complete abrogation of IDT production in isolates of the mutant strain proved the predicted involvement of the target genes in the biosynthesis of IDTs. The mutant isolates continued to produce ergot alkaloids undisturbed, indicating that equivalent mutants generated in industrial ergot producers may have a better safety profile as they are devoid of IDT-type mycotoxins. Meanwhile, ATMT optimized for Claviceps spp. may open the door for the facile genetic engineering of these industrially and ecologically important organisms.

EXTENDING THE USEFUL LIFE OF OLDER MASS SPECTROMETERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, S.; Cordaro, J.; Holland, M.

2010-06-17

Thermal ionization and gas mass spectrometers are widely used across the Department of Energy (DOE) Complex and contractor laboratories. These instruments support critical missions, where high reliability and low measurement uncertainty are essential. A growing number of these mass spectrometers are significantly older than their original design life. The reality is that manufacturers have declared many of the instrument models obsolete, with direct replacement parts and service no longer available. Some of these obsolete models do not have a next generation, commercially available replacement. Today's budget conscious economy demands for the use of creative funds management. Therefore, the ability tomore » refurbish (or upgrade) these valuable analytical tools and extending their useful life is a cost effective option. The Savannah River Site (SRS) has the proven expertise to breathe new life into older mass spectrometers, at a significant cost savings compared to the purchase and installation of new instruments. A twenty-seven year old Finnigan MAT-261{trademark} Thermal Ionization Mass Spectrometer (TIMS), located at the SRS F/H Area Production Support Laboratory, has been successfully refurbished. Engineers from the Savannah River National Laboratory (SRNL) fabricated and installed the new electronics. These engineers also provide continued instrument maintenance services. With electronic component drawings being DOE Property, other DOE Complex laboratories have the option to extend the life of their aged Mass Spectrometers.« less

Early Implementation of Continuous Renal Replacement Therapy Optimizes Casualty Evacuation for Combat-Related Acute Kidney Injury

DTIC Science & Technology

2013-08-01

were Acute Kidney Injury Network (AKIN) 3 and all developed critical hyperkalemia (mean [SD], peak K+ 6.4 [0.4]). The peak plasma creatinine ranged...related acid-base disorders, severe hyperkalemia , and metabolic disorders became apparent. Based on the mounting pressure and internal performance im...with severe hyperkalemia was the most common indication for renal replacement. Validation for critical care evacuation to the Role IV facility mandated a

Non-Carcinogenic Replacements for PBNA Antioxidant in PBXN-105 and PBXN- 106 Explosives

DTIC Science & Technology

1980-01-01

U~3 *y.4~;NWSY TR 801 NON-CARCINOGENIC REPLACEMENTS O ’ ~FOR PBNA ANTIOXIDANT IN PBXN -10.5 AND PBXN - 106 EXPLOSIVESo...... ............. JANUARY 1980... PBXN - 106 Explosive Plastic-Bonded Explosive % ABSSRACT (Continue on reverse olde It neceeeoey end Identify by block number) ’ Explosive mixes of PBXN -105...and PBXN - 106 were prepared using Cyanox 2246 and CAO-14 antioxidants in lieu of phenyl-beta-naphthylamine (PBNA). Specification tests, as well as

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009690 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009683 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld and MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009721 (18 May 2009) --- Astronauts John Grunsfeld (left) and Andrew Feustel, both STS-125 mission specialists, participate in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and Feustel installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-010122 (18 May 2009) --- Astronaut Andrew Feustel, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Feustel and astronaut John Grunsfeld (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009712 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009713 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-010103 (18 May 2009) --- Astronaut Andrew Feustel, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Feustel and astronaut John Grunsfeld (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld and MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009718 (18 May 2009) --- Astronauts John Grunsfeld (bottom) and Andrew Feustel, both STS-125 mission specialists, participate in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and Feustel installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld and MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009706 (18 May 2009) --- Astronauts John Grunsfeld (left) and Andrew Feustel, both STS-125 mission specialists, participate in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and Feustel installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-010047 (18 May 2009) --- Astronaut Andrew Feustel, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Feustel and astronaut John Grunsfeld (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009599 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009688 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009595 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009591 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009717 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009877 (18 May 2009) --- Astronaut Andrew Feustel, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Feustel and astronaut John Grunsfeld (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld and MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009667 (18 May 2009) --- Astronauts John Grunsfeld (left) and Andrew Feustel, both STS-125 mission specialists, participate in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and Feustel installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld and MS5 Feustel during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009603 (18 May 2009) --- Astronauts John Grunsfeld (left) and Andrew Feustel, both STS-125 mission specialists, participate in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and Feustel installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009696 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

STS-125 MS3 Grunsfeld during EVA5

NASA Image and Video Library

2009-05-18

S125-E-009593 (18 May 2009) --- Astronaut John Grunsfeld, STS-125 mission specialist, participates in the mission?s fifth and final session of extravehicular activity (EVA) as work continues to refurbish and upgrade the Hubble Space Telescope. During the seven-hour and two-minute spacewalk, Grunsfeld and astronaut Andrew Feustel (out of frame), mission specialist, installed a battery group replacement, removed and replaced a Fine Guidance Sensor and three thermal blankets (NOBL) protecting Hubble?s electronics.

Early-onset growth hormone deficiency results in diastolic dysfunction in adult-life and is prevented by growth hormone supplementation.

PubMed

Groban, L; Lin, M; Kassik, K A; Ingram, R L; Sonntag, W E

2011-04-01

The primary goal of growth hormone (GH) replacement is to promote linear growth in children with growth hormone deficiency (GHD). GH and insulin-like growth factor-1 (IGF-1) are also known to have roles in cardiac development and as modulators of myocardial structure and function in the adult heart. However, little is known about cardiac diastolic function in young adults with childhood onset GH deficiency in which GH treatment was discontinued following puberty. The aim of the study was to evaluate the effects of long standing GHD and peri-pubertal or continuous GH replacement therapy on diastolic function in the adult dwarf rat. The dwarf rat, which possesses a mutation in a transcription factor necessary for development of the somatotroph, does not exhibit the normal peri-pubertal rise in GH around day 28 and was used to model childhood or early-onset GHD (EOGHD). In another group of male dwarfs, GH replacement therapy was initiated at 4 weeks of age when GH pulsatility normally begins. Ten weeks after initiation of injections, GH-treated dwarf rats were divided into 2 groups; continued treatment with GH for 12 weeks (GH-replete) or treatment with saline for 12 weeks. This latter group models GH supplementation during adolescence with GHD beginning in adulthood (adult-onset GHD; AOGHD). Saline-treated heterozygous (HZ) rats were used as age-matched controls. At 26 weeks of age, cardiac function was assessed using invasive or noninvasive (conventional and tissue Doppler) indices of myocardial contractility and lusitropy. Systolic function, as determined by echocardiography, was similar among groups. Compared with HZ rats and GH-replete dwarfs, the EOGHD group exhibited significant reductions in myocardial relaxation and increases in left ventricular filling pressure, indicative of moderate diastolic dysfunction. This was further associated with a decrease in the cardiac content of sarcoplasmic reticulum Ca(2+) ATPase (SERCA2), one of the important cardiac calcium regulatory proteins. Dwarfs supplemented with GH during the peri-adolescence stage, but not beyond (AOGHD), exhibited a subtle prolongation in the deceleration time to early filling. In contrast, continual GH replacement preserved diastolic function such that the cardiac phenotype of the GH-replete dwarfs resembled that of their age-matched HZ counterpart. Our data indicate that GHD during adolescence leads to overt diastolic dysfunction in early adulthood and this is prevented by continual GH replacement therapy. Since discontinuation of GH replacement following adolescence only mitigated the lusitropic deficits that were observed in untreated dwarfs, GH treatment into adulthood could be beneficial. Copyright © 2011 Growth Hormone Research Society. Published by Elsevier Ltd. All rights reserved.

Accuracy of intravenous infusion pumps in continuous renal replacement therapies.

PubMed

Jenkins, R; Harrison, H; Chen, B; Arnold, D; Funk, J

1992-01-01

Most extracorporeal continuous renal replacement therapies (CRRT) require inflow pumping of either dialysate, filtrate replacement solution, or both. Outflow of spent dialysate and ultrafiltrate can be accomplished by gravity drainage or pump. Intravenous infusion pumps have been commonly used for these purposes, although little is known about the accuracy of these pumps. To evaluate accuracy of two different types of intravenous infusion pumps used in CRRT, we studied flow rates at nine different pressure variations in three piston type and three linear peristaltic pumps. The results showed that error of either pump was not different for flow rates of 4 and 16 ml/min. Both types of pumps were affected by fluid circuit pressures, although pressure conditions under which error was low were different for each pump type. The linear peristaltic pumps were most accurate under conditions of low pump inlet pressure, whereas piston pumps were most accurate under conditions of low pump pressure gradient (outlet minus inlet) of 0 or -100 mmHg. The magnitude of error outside these conditions was substantial, reaching 12.5% for the linear peristaltic pump when inlet pressure was -100 mmHg and outlet pressure was 100 mmHg. Error may be minimized in the clinical setting by choosing the pump type best suited for the pressure conditions expected for the renal replacement modality in use.

Impact of the removal of light and mild descriptors from cigarette packages in Ontario, Canada: switching to "light replacement" brand variants.

PubMed

Cohen, Joanna E; Yang, Jingyan; Donaldson, Elisabeth A

2014-12-01

This study assessed cessation and brand switching among smokers in Ontario, Canada after tobacco companies' voluntary removal of 'light' and 'mild' descriptors from cigarette packages. We analyzed longitudinal data on brand preference and cessation from a cohort of smokers (n=632) in the Ontario Tobacco Survey in Canada from 2006 to 2008 with a longitudinal regression model. While cessation differed by brand variant prior to the ban (7% light vs. 3% regular; P<0.05), it did not differ by brand variant after the ban was implemented. In 2008, when light cigarette brand variants were no longer available, 33% of the sample still reported smoking lights and 31% smoked light replacement brand variants. During each subsequent follow-up, light brand smokers had 2 times the odds of smoking regular brand variants (Adjusted OR: 2.03, 95% CI 1.80,2.29), and almost 5 times the odds of using light replacement brand variants (Adjusted OR: 4.87, 95% CI 4.07,5.84), respectively, compared to continuing to smoke lights. Even after removing misleading descriptors from cigarette packs, smokers continued to report using light brand variants, and many switched to newly introduced light replacement brand variants. After full implementation of the ban, cessation did not vary by brand variant. Copyright © 2014. Published by Elsevier Inc.

45. FINISHING STANDS, 98INCH CONTINUOUS HOT STRIP MILL, WORLD'S LARGEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. FINISHING STANDS, 98-INCH CONTINUOUS HOT STRIP MILL, WORLD'S LARGEST AT THE TIME OF INSTALLATION IN 1937. THE MILL WAS REPLACED BY A NEW 84-INCH MILL IN 1971 AND IS SEEN HERE PARTIALLY DISMANTLED IN PREPARATION FOR DEMOLITION. - Corrigan, McKinney Steel Company, 3100 East Forty-fifth Street, Cleveland, Cuyahoga County, OH

MS Grunsfeld and Linnehan on middeck after EVA 1

NASA Image and Video Library

2002-03-04

STS109-349-027 (4 March 2002) --- Astronauts John M. Grunsfeld and Richard M. Linnehan, STS-109 payload commander and mission specialist, respectively, wearing the liquid cooling and ventilation garment that complements the Extravehicular Mobility Unit (EMU) space suit, are photographed on the mid deck of the Space Shuttle Columbia after the mission’s first session of extravehicular activity (EVA). The EVA-1 team replaced one of the telescope’s two second-generation solar arrays, which is also known as SA2, and a Diode Box Assembly. The solar array was replaced with a new, third-generation solar array, which is called SA3. The space walkers also did some prep work for STS-109’s other space walks.

75 FR 27411 - Airworthiness Directives; Turbomeca Arriel 1B, 1D, 1D1, and 1S1 Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-17

.... That AD requires initial and repetitive relative position checks of the gas generator 2nd stage turbine... repetitive replacements of 2nd stage turbines on Arriel 1B, 1D, and 1D1 engines. This AD requires lowering the initial and repetitive thresholds for replacement of 2nd stage turbines on Arriel 1B, 1D, and 1D1...

Esophageal replacement in children: Challenges and long-term outcomes.

PubMed

Soccorso, Giampiero; Parikh, Dakshesh H

2016-01-01

Replacement of a nonexistent or damaged esophagus continues to pose a significant challenge to pediatric surgeons. Various esophageal replacement grafts and techniques have not produced consistently good outcomes to emulate normal esophagus. Therefore, many techniques are still being practiced and recommended with no clear consensus. We present a concise literature review of the currently used techniques and with discussions on the advantages and anticipated morbidity. There are no randomized controlled pediatric studies to compare different types of esophageal replacements. Management and graft choice are based on geographical and personal predilections rather than on any discernible objective data. The biggest series with long-term outcome are reported for gastric transposition and colonic replacement. Comparison of different studies shows no significant difference in early (graft necrosis and anastomotic leaks) or late complications (strictures, poor feeding, gastro-esophageal reflux, tortuosity of the graft, and Barrett's esophagus). The biggest series seem to have lower complications than small series reflecting the decennials experience in their respective centers. Long-term follow-up is recommended following esophageal replacement for the development of late strictures, excessive tortuosity, and Barrett's changes within the graft. Once child overcomes initial morbidity and establishes oral feeding, long-term consequences and complications of pediatric esophageal replacement should be monitored and managed in adult life.

Esophageal replacement in children: Challenges and long-term outcomes

PubMed Central

Soccorso, Giampiero; Parikh, Dakshesh H.

2016-01-01

Replacement of a nonexistent or damaged esophagus continues to pose a significant challenge to pediatric surgeons. Various esophageal replacement grafts and techniques have not produced consistently good outcomes to emulate normal esophagus. Therefore, many techniques are still being practiced and recommended with no clear consensus. We present a concise literature review of the currently used techniques and with discussions on the advantages and anticipated morbidity. There are no randomized controlled pediatric studies to compare different types of esophageal replacements. Management and graft choice are based on geographical and personal predilections rather than on any discernible objective data. The biggest series with long-term outcome are reported for gastric transposition and colonic replacement. Comparison of different studies shows no significant difference in early (graft necrosis and anastomotic leaks) or late complications (strictures, poor feeding, gastro-esophageal reflux, tortuosity of the graft, and Barrett's esophagus). The biggest series seem to have lower complications than small series reflecting the decennials experience in their respective centers. Long-term follow-up is recommended following esophageal replacement for the development of late strictures, excessive tortuosity, and Barrett's changes within the graft. Once child overcomes initial morbidity and establishes oral feeding, long-term consequences and complications of pediatric esophageal replacement should be monitored and managed in adult life. PMID:27365900

The Feasibility of Palm Kernel Shell as a Replacement for Coarse Aggregate in Lightweight Concrete

NASA Astrophysics Data System (ADS)

Itam, Zarina; Beddu, Salmia; Liyana Mohd Kamal, Nur; Ashraful Alam, Md; Issa Ayash, Usama

2016-03-01

Implementing sustainable materials into the construction industry is fast becoming a trend nowadays. Palm Kernel Shell is a by-product of Malaysia’s palm oil industry, generating waste as much as 4 million tons per annum. As a means of producing a sustainable, environmental-friendly, and affordable alternative in the lightweight concrete industry, the exploration of the potential of Palm Kernel Shell to be used as an aggregate replacement was conducted which may give a positive impact to the Malaysian construction industry as well as worldwide concrete usage. This research investigates the feasibility of PKS as an aggregate replacement in lightweight concrete in terms of compressive strength, slump test, water absorption, and density. Results indicate that by using PKS for aggregate replacement, it increases the water absorption but decreases the concrete workability and strength. Results however, fall into the range acceptable for lightweight aggregates, hence it can be concluded that there is potential to use PKS as aggregate replacement for lightweight concrete.

26. Generator Voltage Regulator Cabinet Exterior for Unit 1, view ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Generator Voltage Regulator Cabinet Exterior for Unit 1, view to the northwest. The exciter supplies the DC current to the generator rotor to create electricity. Each of the four original units has an exciter identical to this one, and all are scheduled for replacement. - Washington Water Power Clark Fork River Noxon Rapids Hydroelectric Development, Powerhouse, South bank of Clark Fork River at Noxon Rapids, Noxon, Sanders County, MT

Acousto-ultrasonic nondestructive evaluation of materials using laser beam generation and detection

NASA Technical Reports Server (NTRS)

Huber, Robert D.; Green, Robert E., Jr.; Vary, Alex; Kautz, Harold

1990-01-01

Presented in viewgraph format, the possibility of using laser generation and detection of ultrasound to replace piezoelectric transducers for the acousto-ultrasonic technique is advanced. The advantages and disadvantages of laser acousto-ultrasonics are outlined. Laser acousto-ultrasonics complements standard piezoelectric acousto-ultrasonics and offers non-contact nondestructive evaluation.

Ultrastable automatic frequency control

NASA Technical Reports Server (NTRS)

Sabourin, D. J.; Furiga, A.

1981-01-01

Center frequency of wideband AFC circuit drifts only hundredths of percent per day. Since circuit responds only to slow frequency drifts and modulation signal has high-pass characteristics, AFC does not interfere with normal FM operation. Stable oscillator, reset circuit, and pulse generator constitute time-averaging discriminator; digital counter in pulse generator replaces usual monostable multivibrator.

Do financial incentives trump clinical guidance? Hip Replacement in England and Scotland.

PubMed

Papanicolas, Irene; McGuire, Alistair

2015-12-01

Following devolution in 1999 England and Scotland's National Health Services diverged, resulting in major differences in hospital payment. England introduced a case payment mechanism from 2003/4, while Scotland continued to pay through global budgets. We investigate the impact this change had on activity for Hip Replacement. We examine the financial reimbursement attached to uncemented Hip Replacement in England, which has been more generous than for its cemented counterpart, although clinical guidance from the National Institute for Clinical Excellence recommends the later. In Scotland this financial differential does not exist. We use a difference-in-difference estimator, using Scotland as a control, to test whether the change in reimbursement across the two countries had an influence on treatment. Our results indicate that financial incentives are directly linked to the faster uptake of the more expensive, uncemented Hip Replacement in England, which ran against the clinical guidance. Copyright © 2015 Elsevier B.V. All rights reserved.

Frequency of pacemaker malfunction associated with monopolar electrosurgery during pulse generator replacement or upgrade surgery.

PubMed

Lin, Yun; Melby, Daniel P; Krishnan, Balaji; Adabag, Selcuk; Tholakanahalli, Venkatakrishna; Li, Jian-Ming

2017-08-01

The aim of this study is to investigate the frequency of electrosurgery-related pacemaker malfunction. A retrospective study was conducted to investigate electrosurgery-related pacemaker malfunction in consecutive patients undergoing pulse generator (PG) replacement or upgrade from two large hospitals in Minneapolis, MN between January 2011 and January 2014. The occurrence of this pacemaker malfunction was then studied by using MAUDE database for all four major device vendors. A total of 1398 consecutive patients from 2 large tertiary referral centers in Minneapolis, MN undergoing PG replacement or upgrade surgery were retrospectively studied. Four patients (0.3% of all patients), all with pacemakers from St Jude Medical (2.8%, 4 of 142) had output failure or inappropriately low pacing rate below 30 bpm during electrosurgery, despite being programmed in an asynchronous mode. During the same period, 1174 cases of pacemaker malfunctions were reported on the same models in MAUDE database, 37 of which (3.2%) were electrosurgery-related. Twenty-four cases (65%) had output failure or inappropriate low pacing rate. The distribution of adverse events was loss of pacing (59.5%), reversion to backup pacing (32.4%), inappropriate low pacing rate (5.4%), and ventricular fibrillation (2.7%). The majority of these (78.5%) occurred during PG replacement at ERI or upgrade surgery. No electrosurgery-related malfunction was found in MAUDE database on 862 pacemaker malfunction cases during the same period from other vendors. Electrosurgery during PG replacement or upgrade surgery can trigger output failure or inappropriate low pacing rate in certain models of modern pacemakers. Cautions should be taken for pacemaker-dependent patients.

Total ankle replacement systems available in the United States.

PubMed

Coetzee, J Chris; Deorio, James K

2010-01-01

Ankle replacement continues to be a viable option for treating patients with ankle arthritis. Over the past 10 years, there has been a significant increase in the number of ankle replacement systems available for use. Current controversy centers on whether fixed- or mobile-bearing devices are most advantageous. Most total ankle systems used outside the United States are mobile-bearing devices, whereas ankle replacement systems used in the United States are all essentially fixed-bearing devices. Not all ankles with degenerative changes are amenable to replacement surgery, and several exclusion criteria are well documented. Ankle replacement is especially complicated because of the ankle's proximity to the foot and the important role that the balance and alignment of the foot play in the success of the ankle replacement. Foot deformities should be treated before or at the time of ankle replacement surgery. Ignoring foot deformities can lead to failure of the ankle replacement. It is also of paramount importance to consider the stability of the ankle ligaments. An unstable ankle with a varus or valgus deformity of more than 20 degrees is probably not amenable to ankle replacement. There are currently no reliable options to predictably reconstruct the lateral or medial ligaments in these severe deformities. It is important to be aware of the ankle replacement systems currently available in the United States and understand the key features of each design. Devices approved by the US Food and Drug Administration, a device that is awaiting approval, and a device that is being evaluated by the Food and Drug Administration in a prospective randomized clinical trial are discussed, along with an objective comparison of fixed- and mobile-bearing devices.

Blood Glucose Monitoring Devices

MedlinePlus

... of interferences ability to transmit data to a computer cost of the meter cost of the test ... Performance FDA expands indication for continuous glucose monitoring system, first to replace fingerstick testing for diabetes treatment ...

Navy Virginia (SSN 774) Class Attack Submarine Procurement: Background and Issues for Congress

DTIC Science & Technology

2016-10-25

proposed plan include the following:  GD/EB is to be the prime contractor for designing and building Ohio replacement boats;  HII/NNS is to be a...boats, and HII/NNS would receive 22%-23%;  GD/EB is to continue as prime contractor for the Virginia-class program, but to help balance out projected...execute this strategy, GDEB has been selected as the prime contractor for OR with the responsibilities to deliver the twelve OR [Ohio replacement

Mesh morphing for finite element analysis of implant positioning in cementless total hip replacements.

PubMed

Bah, Mamadou T; Nair, Prasanth B; Browne, Martin

2009-12-01

Finite element (FE) analysis of the effect of implant positioning on the performance of cementless total hip replacements (THRs) requires the generation of multiple meshes to account for positioning variability. This process can be labour intensive and time consuming as CAD operations are needed each time a specific orientation is to be analysed. In the present work, a mesh morphing technique is developed to automate the model generation process. The volume mesh of a baseline femur with the implant in a nominal position is deformed as the prosthesis location is varied. A virtual deformation field, obtained by solving a linear elasticity problem with appropriate boundary conditions, is applied. The effectiveness of the technique is evaluated using two metrics: the percentages of morphed elements exceeding an aspect ratio of 20 and an angle of 165 degrees between the adjacent edges of each tetrahedron. Results show that for 100 different implant positions, the first and second metrics never exceed 3% and 3.5%, respectively. To further validate the proposed technique, FE contact analyses are conducted using three selected morphed models to predict the strain distribution in the bone and the implant micromotion under joint and muscle loading. The entire bone strain distribution is well captured and both percentages of bone volume with strain exceeding 0.7% and bone average strains are accurately computed. The results generated from the morphed mesh models correlate well with those for models generated from scratch, increasing confidence in the methodology. This morphing technique forms an accurate and efficient basis for FE based implant orientation and stability analysis of cementless hip replacements.

Randomized comparative trial of nicotine polacrilex, a transdermal patch, nasal spray, and an inhaler.

PubMed

Hajek, P; West, R; Foulds, J; Nilsson, F; Burrows, S; Meadow, A

1999-09-27

There are several nicotine replacement products on the market, and physicians are likely to be asked with increasing frequency about which of these products their patients should use. To provide a basis for rational advice by comparing nicotine polacrilex (gum), a transdermal patch, nasal spray, and an inhaler. Randomized trial with assessments at the quit date and 1, 4, and 12 weeks later. Hospital smokers' clinic. Male and female community volunteers (N = 504) smoking 10 or more cigarettes per day and seeking help to stop smoking. Patients were given brief advice, and purchased their nicotine replacement treatment at approximately half the regular retail price. Nicotine replacement treatment use, ratings of withdrawal symptoms, ratings of product characteristics and helpfulness, and biochemically validated continuous lapse-free abstinence. The products did not differ in their effects on withdrawal discomfort, urges to smoke, or rates of abstinence. The continuous validated 12-week abstinence rates were 20%, 21%, 24%, and 24% in the gum, patch, spray, and inhaler groups, respectively. Compliance with recommended nicotine replacement treatment use was high for the patch, low for gum, and very low for the spray and the inhaler. The spray was underused because of adverse effects more often than the other products. In the subjects using the spray, the level of use among abstainers at week 1 predicted outcome at week 12. The inhaler was rated as more embarrassing to use than the other products, but provided at least as much nicotine as the gum. When asked about nicotine replacement treatment products available, physicians should note that, despite low compliance with the recommended dose of the spray and inhaler and differences in product ratings, overall, there are no notable differences between the products in their effects on withdrawal discomfort, perceived helpfulness, or general efficacy.

Comparison Of In Situ Soil Moisture Measurements: An Examination of the Neutron and Dielectric Measurements within the Illinois Climate Network

USDA-ARS?s Scientific Manuscript database

The continuity of soil moisture time series data is crucial for climatic research. Yet, a common problem for continuous data series is the changing of sensors, not only as replacements are necessary, but as technologies evolve. The Illinois Climate Network has one of the longest data records of soi...

Nursing essential principles: continuous renal replacement therapy.

PubMed

Richardson, Annette; Whatmore, Jayne

2015-01-01

This article aims to guide critical care nurses with the care and management of patients on continuous renal replacement therapy (CRRT). CRRT, a highly specialized therapy involving complex nursing care, is used widely in the intensive care unit to treat patients with acute kidney injury. A literature search was conducted using CINAHL, Medline from PubMed and BNI using the search terms CRRT or continuous veno-venous haemofiltration and nursing or nurses from 2000 onwards and limited to the English language. The appraised evidence and expert opinion is used in this article. Four essential nursing principles for CRRT are reviewed (1) the importance of continuous assessment of the indications to influence the appropriate mode; (2) ensuring good vascular access; (3) the avoidance of unnecessary interruptions and (4) the prevention of complications. The identified four essential nursing principles provide guidance on this complex aspects of nursing practice. Specific nursing research to guide the care and management of this therapy is limited so should be explored in the future. Critical care nurses caring for and managing patients on CRRT require an understanding of how to deliver safe CRRT. © 2014 British Association of Critical Care Nurses.

Changing of the guard: reducing infection when replacing neural pacemakers.

PubMed

Pepper, Joshua; Meliak, Lara; Akram, Harith; Hyam, Jonathan; Milabo, Catherine; Candelario, Joseph; Foltynie, Thomas; Limousin, Patricia; Curtis, Carmel; Hariz, Marwan; Zrinzo, Ludvic

2017-04-01

OBJECTIVE Infection of deep brain stimulation (DBS) hardware has a significant impact on patient morbidity. Previous experience suggests that infection rates appear to be higher after implantable pulse generator (IPG) replacement surgery than after the de novo DBS procedure. In this study the authors examine the effect of a change in practice during DBS IPG replacements at their institution. METHODS Starting in January 2012, patient screening for methicillin-resistant Staphylococcus aureus (MRSA) and, and where necessary, eradication was performed prior to elective DBS IPG change. Moreover, topical vancomycin was placed in the IPG pocket during surgery. The authors then prospectively examined the infection rate in patients undergoing DBS IPG replacement at their center over a 3-year period with at least 9 months of follow-up. RESULTS The total incidence of infection in this prospective consecutive series of 101 IPG replacement procedures was 0%, with a mean follow-up duration of 24 ± 11 months. This was significantly lower than the authors' previously published historical control group, prior to implementing the change in practice, where the infection rate for IPG replacement was 8.5% (8/94 procedures; p = 0.003). CONCLUSIONS This study suggests that a change in clinical practice can significantly lower infection rates in patients undergoing DBS IPG replacement. These simple measures can minimize unnecessary surgery, loss of benefit from chronic stimulation, and costly hardware replacement, further improving the cost efficacy of DBS therapies.

Conestat alfa for the treatment of angioedema attacks

PubMed Central

Davis, Benjamin; Bernstein, Jonathan A

2011-01-01

Recently, multiple C1 inhibitor (C1-INH) replacement products have been approved for the treatment of hereditary angioedema (HAE). This review summarizes HAE and its current treatment modalities and focuses on findings from bench to bedside trials of a new C1-INH replacement, conestat alfa. Conestat alfa is unique among the other C1-INH replacement products because it is produced from transgenic rabbits rather than derived from human plasma donors, which can potentially allow an unlimited source of drug without any concern of infectious transmission. The clinical trial data generated to date indicate that conestat alfa is safe and effective for the treatment of acute HAE attacks. PMID:21753889

Micafungin Plasma Levels Are Not Affected by Continuous Renal Replacement Therapy: Experience in Critically Ill Patients.

PubMed

Vossen, M G; Knafl, D; Haidinger, M; Lemmerer, R; Unger, M; Pferschy, S; Lamm, W; Maier-Salamon, A; Jäger, W; Thalhammer, F

2017-08-01

Critically ill patients often experience acute kidney injury and the need for renal replacement therapy in the course of their treatment in an intensive care unit (ICU). These patients are at an increased risk for candidiasis. Although there have been several reports of micafungin disposition during renal replacement therapy, to this date there are no data describing the elimination of micafungin during high-dose continuous venovenous hemodiafiltration with modified AN69 membranes. The aim of this prospective open-label pharmacokinetic study was to assess whether micafungin plasma levels are affected by continuous hemodiafiltration in critical ill patients using the commonly employed AN69 membrane. A total of 10 critically ill patients with micafungin treatment due to suspected or proven candidemia were included in this trial. Prefilter/postfilter micafungin clearance was measured to be 46.0 ml/min (±21.7 ml/min; n = 75 individual time points), while hemofilter clearance calculated by the sieving coefficient was 0.0038 ml/min (±0.002 ml/min; n = 75 individual time points). Total body clearance was measured to be 14.0 ml/min (±7.0 ml/min; n = 12). The population area under the curve from 0 to 24 h (AUC 0-24 ) was calculated as 158.5 mg · h/liter (±79.5 mg · h/liter; n = 13). In spite of high protein binding, no dose modification is necessary in patients receiving continuous venovenous hemodiafiltration with AN69 membranes. A dose elevation may, however, be justified in certain cases. (This study has been registered at ClinicalTrials.gov under identifier NCT02651038.). Copyright © 2017 American Society for Microbiology.

New Subarray Readout Patterns for the ACS Wide Field Channel

NASA Astrophysics Data System (ADS)

Golimowski, D.; Anderson, J.; Arslanian, S.; Chiaberge, M.; Grogin, N.; Lim, Pey Lian; Lupie, O.; McMaster, M.; Reinhart, M.; Schiffer, F.; Serrano, B.; Van Marshall, M.; Welty, A.

2017-04-01

At the start of Cycle 24, the original CCD-readout timing patterns used to generate ACS Wide Field Channel (WFC) subarray images were replaced with new patterns adapted from the four-quadrant readout pattern used to generate full-frame WFC images. The primary motivation for this replacement was a substantial reduction of observatory and staff resources needed to support WFC subarray bias calibration, which became a new and challenging obligation after the installation of the ACS CCD Electronics Box Replacement during Servicing Mission 4. The new readout patterns also improve the overall efficiency of observing with WFC subarrays and enable the processing of subarray images through stages of the ACS data calibration pipeline (calacs) that were previously restricted to full-frame WFC images. The new readout patterns replace the original 512×512, 1024×1024, and 2048×2046-pixel subarrays with subarrays having 2048 columns and 512, 1024, and 2048 rows, respectively. Whereas the original square subarrays were limited to certain WFC quadrants, the new rectangular subarrays are available in all four quadrants. The underlying bias structure of the new subarrays now conforms with those of the corresponding regions of the full-frame image, which allows raw frames in all image formats to be calibrated using one contemporaneous full-frame "superbias" reference image. The original subarrays remain available for scientific use, but calibration of these image formats is no longer supported by STScI.

Dynamics of plasma proteome during leptin-replacement therapy in genetically based leptin deficiency.

PubMed

Andreev, V P; Dwivedi, R C; Paz-Filho, G; Krokhin, O V; Wong, M-L; Wilkins, J A; Licinio, J

2011-06-01

The effects of leptin-replacement therapy on the plasma proteome of three unique adults with genetically based leptin deficiency were studied longitudinally during the course of recombinant human leptin-replacement treatment. Quantitative proteomics analysis was performed in plasma samples collected during four stages: before leptin treatment was initiated, after 1.5 and 6 years of leptin-replacement treatment, and after 7 weeks of temporary interruption of leptin-replacement therapy. Of 500 proteins reliably identified and quantitated in those four stages, about 100 were differentially abundant twofold or more in one or more stages. Synchronous dynamics of abundances of about 90 proteins was observed reflecting both short- and long-term effects of leptin-replacement therapy. Pathways and processes enriched with overabundant synchronous proteins were cell adhesion, cytoskeleton remodeling, cell cycle, blood coagulation, glycolysis, and gluconeogenesis. Plausible common regulators of the above synchronous proteins were identified using transcription regulation network analysis. The generated network included two transcription factors (c-Myc and androgen receptor) that are known to activate each other through a double-positive feedback loop, which may represent a potential molecular mechanism for the long-term effects of leptin-replacement therapy. Our findings may help to elucidate the effects of leptin on insulin resistance.

Provide, provide: the economics of aging.

PubMed

1998-06-26

Most older persons face two potentially serious economic problems: (a) declining earning power and (b) declining health that can be partly offset by increased utilization of health care. The decline in earning power is largely attributable to physiological changes and to obsolescence of skills and knowledge. These adverse effects are exacerbated by public and private policies that reduce the incentives of older persons to continue work and increase the cost to employers of employing older workers. The problems of earnings replacement and health care payment are usually discussed separately, but there are several reasons why they should be considered together. First, there are often tradeoffs between the two. Money is money, and for most people there is never enough to go around. This is self-evident where private funds are concerned. Low-income elderly, for instance, frequently must choose between expensive prescription drugs and an adequate diet. For middle-income elderly, the choice may be between saving on medigap insurance or forgoing an airplane trip to a grandchild's graduation. Difficult choices are also inherent in the allocation of public funds. The same tax receipts that could be used to maintain or increase retirement benefits could be used to fund additional care, and vice versa. In discussing these tradeoffs, some analysts assert that people will gladly give up other goods and services for medical care that cures illness, relieves pain, or restores function. Others believe that some people would forgo some health insurance in order to maintain access to other goods and services. A second reason for looking at the two problems together is that they pose similar questions for public policy. How much should each generation provide for its own needs in old age, and how much should be provided by the generations that follow? How much provision should be voluntary, how much compulsory? How much intra-generational redistribution is appropriate after age 65? How well can private markets serve the elderly's desire for annuities and health insurance, and when are public programs more efficient? Finally, the problem of health care payment is approaching that of earning replacement in economic importance and, by 2020, will far exceed it. Declining health after age 65 results in substantial increase in use of prescription drugs, hospital admissions, repair or replacement of parts of the body, rehabilitation and physical therapy, and assistance with activities of daily living. New technologies offer great promise for offsetting the health problems of aging, but often at considerable expense. Overall, per capita expenditures for health care after age 65 are between three and four times as great as for those under 65. This presentation will focus primarily on the (thus far) inexorable increase in consumption of health care by older Americans. If this increase continues and if the government's share of the total remains unchanged, the tax burden on younger cohorts could become intolerable. Concomitantly, if the private share remains unchanged, the ability of the elderly to obtain other goods and services would be sharply diminished. Although the emphasis of the session will be on aggregate and average results, levels and trends in income inequality among the elderly will also be examined and compared with inequality at younger ages. The session will conclude with a discussion of changes that might avert the economic and social crises foreshadowed in the data.

Successful Pregnancies and Deliveries in a Patient With Evolving Hypopituitarism due to Pituitary Stalk Transection Syndrome: Role of Growth Hormone Replacement

PubMed Central

Yoshizawa, Miyako; Ieki, Yasuhiko; Takazakura, Eisuke; Fukuta, Kaori; Hidaka, Takao; Wakasugi, Takanobu; Shimatsu, Akira

2017-01-01

We herein report a 31-year-old Japanese woman with evolving hypopituitarism due to pituitary stalk transection syndrome. She had a history of short stature treated with growth hormone (GH) in childhood and had hypothyroidism and primary amenorrhea at 20 years old. Levothyroxine replacement and recombinant follicle stimulating hormone-human chorionic gonadotropin (FSH-hCG) therapy for ovulation induction were started. GH replacement therapy (GHRT) was resumed when she was 26 years old. She developed mild adrenocortical insufficiency at 31 years old. She succeeded in becoming pregnant and delivered twice. GHRT was partially continued during pregnancy and stopped at the end of the second trimester without any complications. PMID:28250299

In-orbit performance of the ITOS improved attitude control system with Hall generator brushless motor and earth-splitting technique

NASA Technical Reports Server (NTRS)

Peacock, W. M.

1973-01-01

The National Aeronautics and Space Administration (NASA), launched ITOS-D with an improved attitude control system. A Hall generator brushless dc torque motor replaced the brush dc torque motor on Tiros-M and ITOS-A. Two CO2 attitude horizon sensors and one mirror replaced the four wideband horizon sensors and two mirrors on ITOS-1 and NOAA-1. Redundant pitch-control electronic boxes containing additional electronic circuitry for earth-splitting and brushless motor electronics were used. A method of generating a spacecraft earth-facing side reference for comparison to the time occurrence of the earth-splitting pulse was used to automatically correct pitch-attitude error. A single rotating flywheel, supported by a single bearing, provided gyroscopic stability and the required momentum interchange to keep one side of the satellite facing the earth. Magnetic torquing against the earth's magnetic field eliminated the requirement for expendable propellants which would limit satellite life in orbit.

Second-Generation Phenylthiazole Antibiotics with Enhanced Pharmacokinetic Properties.

PubMed

Seleem, Mohammed A; Disouky, Ahmed M; Mohammad, Haroon; Abdelghany, Tamer M; Mancy, Ahmed S; Bayoumi, Sammar A; Elshafeey, Ahmed; El-Morsy, Ahmed; Seleem, Mohamed N; Mayhoub, Abdelrahman S

2016-05-26

A series of second-generation analogues for 2-(1-(2-(4-butylphenyl)-4-methylthiazol-5-yl)ethylidene)aminoguanidine (1) have been synthesized and tested against methicillin-resistant Staphylococcus aureus (MRSA). The compounds were designed with the objective of improving pharmacokinetic properties. This main aim has been accomplished by replacing the rapidly hydrolyzable Schiff-base moiety of first-generation members with a cyclic, unhydrolyzable pyrimidine ring. The hydrazide-containing analogue 17 was identified as the most potent analogue constructed thus far. The corresponding amine 8 was 8 times less active. Finally, incorporating the nitrogenous side chain within an aromatic system completely abolished the antibacterial character. Replacement of the n-butyl group with cyclic bioisosteres revealed cyclohexenyl analogue 29, which showed significant improvement in in vitro anti-MRSA potency. Increasing or decreasing the ring size deteriorated the antibacterial activity. Compound 17 demonstrated a superior in vitro and in vivo pharmacokinetic profile, providing compelling evidence that this particular analogue is a good drug candidate worthy of further analysis.

Generation of functional organs from stem cells.

PubMed

Liu, Yunying; Yang, Ru; He, Zuping; Gao, Wei-Qiang

2013-01-01

We are now well entering the exciting era of stem cells. Potential stem cell therapy holds great promise for the treatment of many diseases such as stroke, traumatic brain injury, Alzheimer's disease, Parkinson's disease, amyotrophic lateral-sclerosis, myocardial infarction, muscular dystrophy, diabetes, and etc. It is generally believed that transplantation of specific stem cells into the injured tissue to replace the lost cells is an effective way to repair the tissue. In fact, organ transplantation has been successfully practiced in clinics for liver or kidney failure. However, the severe shortage of donor organs has been a major obstacle for the expansion of organ transplantation programs. Toward that direction, generation of transplantable organs using stem cells is a desirable approach for organ replacement and would be of great interest for both basic and clinical scientists. Here we review recent progress in the field of organ generation using various methods including single adult tissue stem cells, a blastocyst complementation system, tissue decellularization/recellularization and a combination of stem cells and tissue engineering.

Properties of concrete containing ground palm oil fuel ash as fine aggregate replacement

NASA Astrophysics Data System (ADS)

Saffuan, W. A.; Muthusamy, K.; Salleh, N. A. Mohd; Nordin, N.

2017-11-01

Environmental degradation resulting from increasing sand mining activities and disposal of palm oil fuel ash (POFA), a solid waste generated from palm oil mill needs to be resolved. Thus, the present research investigates the effect of ground palm oil fuel ash as partial fine aggregate replacement on workability, compressive and flexural strength of concrete. Five mixtures of concrete containing POFA as partial sand replacement designed with 0%, 10%, 20%, 30% and 40% of POFA by the weight of sand were used in this experimental work. The cube and beam specimens were casted and water cured up to 28 days before subjected to compressive strength and flexural strength testing respectively. Finding shows that concrete workability reduces as the amount of POFA added become larger. It is worth to note that 10% of POFA is the best amount to be used as partial fine aggregate replacement to produce concrete with enhanced strength.

From the Cover: Cell-replacement therapy for diabetes: Generating functional insulin-producing tissue from adult human liver cells

NASA Astrophysics Data System (ADS)

Sapir, Tamar; Shternhall, Keren; Meivar-Levy, Irit; Blumenfeld, Tamar; Cohen, Hamutal; Skutelsky, Ehud; Eventov-Friedman, Smadar; Barshack, Iris; Goldberg, Iris; Pri-Chen, Sarah; Ben-Dor, Lya; Polak-Charcon, Sylvie; Karasik, Avraham; Shimon, Ilan; Mor, Eytan; Ferber, Sarah

2005-05-01

Shortage in tissue availability from cadaver donors and the need for life-long immunosuppression severely restrict the large-scale application of cell-replacement therapy for diabetic patients. This study suggests the potential use of adult human liver as alternate tissue for autologous beta-cell-replacement therapy. By using pancreatic and duodenal homeobox gene 1 (PDX-1) and soluble factors, we induced a comprehensive developmental shift of adult human liver cells into functional insulin-producing cells. PDX-1-treated human liver cells express insulin, store it in defined granules, and secrete the hormone in a glucose-regulated manner. When transplanted under the renal capsule of diabetic, immunodeficient mice, the cells ameliorated hyperglycemia for prolonged periods of time. Inducing developmental redirection of adult liver offers the potential of a cell-replacement therapy for diabetics by allowing the patient to be the donor of his own insulin-producing tissue. pancreas | transdifferentiation

Changing pollutants to green biogases for the crop food cycle chain.

PubMed

Zong, B Y; Xu, F J; Zong, B D; Zhang, Z G

2012-09-01

When fossil fuels on the Earth are used up, which kind of green energy can be used to replace them? Do every bioenergy generation or crop food chain results in environmental pollution? These questions are major concerns in a world facing restricted supplies of energy and food as well as environmental pollutions. To alleviate these issues, option biogases are explored in this paper. Two types of biogas generators were used for modifying the traditional crop food chain [viz. from atmospheric CO(2) photosynthesis to crops, crop stem/husk biowastes (burnt in cropland or as home fuels), to livestock droppings (dumping away), pork and people foods, then to CO(2)], via turning the biowaste pollutants into green bioenergies. By analyzing the traditional food chain via observation method, the drawbacks of by-product biowastes were revealed. Also, the whole cycle chain was further analyzed to assess its "greenness," using experimental data and other information, such as the material balance (e.g., the absorbed CO(2), investment versus generated food, energy, and wastes). The data show that by using the two types of biogas generators, clean renewable bioenergy, crop food, and livestock meat could be continuously produced without creating any waste to the world. The modification chain largely reduced CO(2) greenhouse gas and had a low-cost investment. The raw materials for the gas generators were only the wastes of crop stems and livestock droppings. Thus, the recommended CO(2) bioenergy cycle chain via the modification also greatly solved the environmental biowaste pollutions in the world. The described two type biogases effectively addressed the issues on energy, food, and environmental pollution. The green renewable bioenergy from the food cycle chain may be one of suitable alternatives to fossil and tree fuels for agricultural countries.

Coming Soon: A New Generation of Assessments

ERIC Educational Resources Information Center

Doorey, Nancy A.

2013-01-01

A short 27 months ago, two groups of U.S. states were each awarded more than $175 million to design, develop, and pilot test a new generation of assessments (U.S. Department of Education, 2010). These new tests will replace assessments in English language arts and mathematics that are currently in use within state and federal accountability…

Chrysler improved numerical differencing analyzer for third generation computers CINDA-3G

NASA Technical Reports Server (NTRS)

Gaski, J. D.; Lewis, D. R.; Thompson, L. R.

1972-01-01

New and versatile method has been developed to supplement or replace use of original CINDA thermal analyzer program in order to take advantage of improved systems software and machine speeds of third generation computers. CINDA-3G program options offer variety of methods for solution of thermal analog models presented in network format.

Sustaining Moore's law with 3D chips

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeBenedictis, Erik P.; Badaroglu, Mustafa; Chen, An

Here, rather than continue the expensive and time-consuming quest for transistor replacement, the authors argue that 3D chips coupled with new computer architectures can keep Moore's law on its traditional scaling path.

Sustaining Moore's law with 3D chips

DOE PAGES

DeBenedictis, Erik P.; Badaroglu, Mustafa; Chen, An; ...

2017-08-01

Here, rather than continue the expensive and time-consuming quest for transistor replacement, the authors argue that 3D chips coupled with new computer architectures can keep Moore's law on its traditional scaling path.

Bridge condition assessment using remote sensors.

DOT National Transportation Integrated Search

2013-02-01

The challenges of a deteriorating and aged infrastructure continue to challenge transportation : authorities as they align maintenance and replacement priorities with decreasing funds. The : United States is home to nearly 600,000 highway bridges of ...

Phaseout of Ozone-Depleting Substances

EPA Pesticide Factsheets

An overview of the HCFC phaseout requirements summaries of the most recent rulemakings. Provides resources for HCFC equipment owners that discuss continued use of HCFC refrigerant, and options for retrofitting or replacing specific types of equipment.

Discrete anti-gravity

NASA Astrophysics Data System (ADS)

Noyes, H. Pierre; Starson, Scott

1991-03-01

Discrete physics, because it replaces time evolution generated by the energy operator with a global bit-string generator (program universe) and replaces fields with the relativistic Wheeler-Feynman action at a distance, allows the consistent formulation of the concept of signed gravitational charge for massive particles. The resulting prediction made by this version of the theory is that free anti-particles near the surface of the earth will fall up with the same acceleration that the corresponding particles fall down. So far as we can see, no current experimental information is in conflict with this prediction of our theory. The experiment crusis will be one of the anti-proton or anti-hydrogen experiments at CERN. Our prediction should be much easier to test than the small effects which those experiments are currently designed to detect or bound.

Solid Waste Assurance Program Implementation Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irons, L.G.

1995-06-19

On June 6, 1995, a waiver to Hanford Site Solid Waste Acceptance Criteria, was approved by the US Department of Energy Richland Operations Office (RL) to replace the low-level, mixed, and transuranic (TRU) generator assessment programs with the Solid Waste Assurance Program (SWAP). This is associated with a waiver that was approved on March 16, 1995 to replace the Storage/Disposal Approval Record (SDAR) requirements with the Waste Specification System (WSS). This implementation plan and the SWAP applies to Solid Waste Disposal (SWD) functions, facilities, and personnel who perform waste acceptance, verification, receipt, and management functions of dangerous, radioactive, and mixedmore » waste from on- and off-site generators who ship to or within the Hanford Site for treatment, storage, and/or disposal (TSD) at SWD TSD facilities.« less

Femoral Access and Delivery of Continuous Renal Replacement Therapy Dose.

PubMed

Bellomo, Rinaldo; Mårtensson, Johan; Lo, Serigne; Kaukonen, Kirsi-Maija; Cass, Alan; Gallagher, Martin

2016-01-01

The study aims to describe the use of dialysis catheters in critically ill patients treated with continuous renal replacement therapy (CRRT) and to study the impact of femoral versus non-femoral access on CRRT dose. Statistical analysis and predictive modelling of data from the Randomized Evaluation of Normal vs. Augmented Level renal replacement therapy trial. The femoral vein was the first access site in 937 (67%) of 1,399 patients. These patients had higher Acute Physiology and Chronic Health Evaluation and Sequential Organ Failure Assessment scores (p = 0.009) and lower pH (p < 0.001) but similar mortality to patients with non-femoral access (44 vs. 45%; p = 0.63). Lower body weight was independently associated with femoral access placement (OR 0.97, 95% CI 0.96-0.98). Femoral access was associated with a 1.03% lower CRRT dose (p = 0.05), but a 4.20% higher dose was achieved with 13.5 Fr catheters (p = 0.03). Femoral access was preferred in lighter and sicker patients. Catheter gauge had greater impact than catheter site in CRRT dose delivery. Video Journal Club "Cappuccino with Claudio Ronco" at http://www.karger.com/?doi=439581. © 2015 S. Karger AG, Basel.

Dissolved oxygen concentration in the medium during cell culture: Defects and improvements.

PubMed

Zhang, Kuan; Zhao, Tong; Huang, Xin; He, Yunlin; Zhou, Yanzhao; Wu, Liying; Wu, Kuiwu; Fan, Ming; Zhu, Lingling

2016-03-01

In vitro cell culture has provided a useful model to study the effects of oxygen on cellular behavior. However, it remains unknown whether the in vitro operations themselves affect the medium oxygen levels and the living states of cells. In addition, a prevailing controversy is whether reactive oxygen species (ROS) production is induced by continuous hypoxia or reoxygenation. In this study, we have measured the effects of different types of cell culture containers and the oxygen environment where medium replacement takes place on the actual oxygen tension in the medium. We found that the deviations of oxygen concentrations in the medium are much greater in 25-cm(2) flasks than in 24-well plates and 35-mm dishes. The dissolved oxygen concentrations in the medium were increased after medium replacement in normoxia, but remained unchanged in glove boxes in which the oxygen tension remained at a low level (11.4, 5.7, and 0.5% O2 ). We also found that medium replacement in normoxia increased the number of ROS-positive cells and reduced the cell viability; meanwhile, medium replacement in a glove box did not produce the above effects. Therefore, we conclude that the use of 25-cm(2) flasks should be avoided and demonstrate that continuous hypoxia does not produce ROS, whereas the reoxygenation that occurs during the harvesting of cells leads to ROS and induces cell death. © 2015 International Federation for Cell Biology.

Kerr optical frequency combs: theory, applications and perspectives

NASA Astrophysics Data System (ADS)

Chembo, Yanne K.

2016-06-01

The optical frequency comb technology is one of the most important breakthrough in photonics in recent years. This concept has revolutionized the science of ultra-stable lightwave and microwave signal generation. These combs were originally generated using ultrafast mode-locked lasers, but in the past decade, a simple and elegant alternativewas proposed,which consisted in pumping an ultra-high-Q optical resonator with Kerr nonlinearity using a continuous-wave laser. When optimal conditions are met, the intracavity pump photons are redistributed via four-wave mixing to the neighboring cavity modes, thereby creating the so-called Kerr optical frequency comb. Beyond being energy-efficient, conceptually simple, and structurally robust, Kerr comb generators are very compact devices (millimetric down to micrometric size) which can be integrated on a chip. They are, therefore, considered as very promising candidates to replace femtosecond mode-locked lasers for the generation of broadband and coherent optical frequency combs in the spectral domain, or equivalently, narrow optical pulses in the temporal domain. These combs are, moreover, expected to provide breakthroughs in many technological areas, such as integrated photonics, metrology, optical telecommunications, and aerospace engineering. The purpose of this review article is to present a comprehensive survey of the topic of Kerr optical frequency combs.We provide an overview of the main theoretical and experimental results that have been obtained so far. We also highlight the potential of Kerr combs for current or prospective applications, and discuss as well some of the open challenges that are to be met at the fundamental and applied level.

Next generation of novel psychoactive substances on the horizon - A complex problem to face.

PubMed

Zawilska, Jolanta B; Andrzejczak, Dariusz

2015-12-01

The last decade has seen a rapid and continuous growth in the availability and use of novel psychoactive substances (NPS) across the world. Although various products are labeled with warnings "not for human consumption", they are intended to mimic psychoactive effects of illicit drugs of abuse. Once some compounds become regulated, new analogues appear in order to satisfy consumers' demands and at the same time to avoid criminalization. This review presents updated information on the second generation of NPS, introduced as replacements of the already banned substances from this class, focusing on their pharmacological properties and metabolism, routes of administration, and effects in humans. Literature search, covering years 2013-2015, was performed using the following keywords alone or in combination: "novel psychoactive substances", "cathinones", "synthetic cannabinoids", "benzofurans", "phenethylamines", "2C-drugs", "NBOMe", "methoxetamine", "opioids", "toxicity", and "metabolism". More than 400 NPS have been reported in Europe, with 255 detected in 2012-2014. The most popular are synthetic cannabimimetics and psychostimulant cathinones; use of psychedelics and opioids is less common. Accumulating experimental and clinical data indicate that potential harms associated with the use of second generation NPS could be even more serious than those described for the already banned drugs. NPS are constantly emerging on the illicit drug market and represent an important health problem. A significant amount of research is needed in order to fully quantify both the short and long term effects of the second generation NPS, and their interaction with other drugs of abuse. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Water Use in Enhanced Geothermal Systems (EGS): Geology of U.S. Stimulation Projects, Water Costs, and Alternative Water Source Policies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harto, C. B.; Schroeder, J. N.; Horner, R. M.

According to the Energy Information Administration (EIA) of the U.S. Department of Energy (DOE), geothermal energy generation in the United States is projected to more than triple by 2040 (EIA 2013). This addition, which translates to more than 5 GW of generation capacity, is anticipated because of technological advances and an increase in available sources through the continued development of enhanced geothermal systems (EGSs) and low-temperature resources (EIA 2013). Studies have shown that air emissions, water consumption, and land use for geothermal electricity generation have less of an impact than traditional fossil fuel–based electricity generation; however, the long-term sustainability ofmore » geothermal power plants can be affected by insufficient replacement of aboveground or belowground operational fluid losses resulting from normal operations (Schroeder et al. 2014). Thus, access to water is therefore critical for increased deployment of EGS technologies and, therefore, growth of the geothermal sector. This paper examines water issues relating to EGS development from a variety of perspectives. It starts by exploring the relationship between EGS site geology, stimulation protocols, and below ground water loss, which is one of the largest drivers of water consumption for EGS projects. It then examines the relative costs of different potential traditional and alternative water sources for EGS. Finally it summarizes specific state policies relevant to the use of alternative water sources for EGS, and finally explores the relationship between EGS site geology, stimulation protocols, and below ground water loss, which is one of the largest drivers of water consumption for EGS projects.« less

Water Use in Enhanced Geothermal Systems (EGS): Geology of U.S. Stimulation Projects, Water Costs, and Alternative Water Use Policies

DOE Data Explorer

Schroeder, Jenna N.

2014-12-16

According to the Energy Information Administration (EIA) of the U.S. Department of Energy (DOE), geothermal energy generation in the United States is projected to more than triple by 2040 (EIA 2013). This addition, which translates to more than 5 GW of generation capacity, is anticipated because of technological advances and an increase in available sources through the continued development of enhanced geothermal systems (EGSs) and low-temperature resources (EIA 2013). Studies have shown that air emissions, water consumption, and land use for geothermal electricity generation have less of an impact than traditional fossil fuel?based electricity generation; however, the long-term sustainability of geothermal power plants can be affected by insufficient replacement of aboveground or belowground operational fluid losses resulting from normal operations (Schroeder et al. 2014). Thus, access to water is therefore critical for increased deployment of EGS technologies and, therefore, growth of the geothermal sector. This paper examines water issues relating to EGS development from a variety of perspectives. It starts by exploring the relationship between EGS site geology, stimulation protocols, and below ground water loss, which is one of the largest drivers of water consumption for EGS projects. It then examines the relative costs of different potential traditional and alternative water sources for EGS. Finally it summarizes specific state policies relevant to the use of alternative water sources for EGS, and finally explores the relationship between EGS site geology, stimulation protocols, and below ground water loss, which is one of the largest drivers of water consumption for EGS projects.