Insight into the risk of replenishing urban landscape ponds with reclaimed wastewater.

PubMed

Chen, Rong; Ao, Dong; Ji, Jiayuan; Wang, Xiaochang C; Li, Yu-You; Huang, Yue; Xue, Tao; Guo, Hongbing; Wang, Nan; Zhang, Lu

2017-02-15

Increasing use of reclaimed wastewater (RW) for replenishing urban landscape ponds has aroused public concern about the water quality. Three ponds replenished with RW in three cities in China were chosen to investigate 22 indexes of water quality in five categories. This was achieved by comparing three pairs of ponds in the three different cities, where one pond in each pair was replenished with RW and the other with surface water (SW). The nutrients condition, heavy metal concentration and ecotoxicity did not differ significantly between RW- and SW-replenished ponds. By contrast, significant differences were observed in algal growth and pathogen risk. RW ponds presented a Cyanophyta-Chlorophyta-Bacillariophyta type with high algal diversity while SW ponds presented a Cyanophyta type with low diversity. Regrowth of bacterial pathogens and especially survival of viral pathogens in RW, was the main driver behind the higher risk for RW ponds compared with SW ones. The duration of RW replenishment was proved to have a marked impact on the algal growth and pathogen risk. With continued RW replenishment, non-dominant algal species subjected to decrease while dominant species were enhanced resulting in the biomass increasing but diversity declining, and the risk posed by viral pathogens might become greater. Copyright © 2016 Elsevier B.V. All rights reserved.

12 CFR 221.116 - Bank loans to replenish working capital used to purchase mutual fund shares.

Code of Federal Regulations, 2010 CFR

2010-01-01

... purchase mutual fund shares. 221.116 Section 221.116 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED... Bank loans to replenish working capital used to purchase mutual fund shares. (a) In a situation considered by the Board of Governors, a business concern (X) proposed to purchase mutual fund shares, from...

12 CFR 221.116 - Bank loans to replenish working capital used to purchase mutual fund shares.

Code of Federal Regulations, 2011 CFR

2011-01-01

... purchase mutual fund shares. 221.116 Section 221.116 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED... Bank loans to replenish working capital used to purchase mutual fund shares. (a) In a situation considered by the Board of Governors, a business concern (X) proposed to purchase mutual fund shares, from...

Silicon web process development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Skutch, M. E.; Driggers, J. M.; Hopkins, R. H.

1981-01-01

The silicon web process takes advantage of natural crystallographic stabilizing forces to grow long, thin single crystal ribbons directly from liquid silicon. The ribbon, or web, is formed by the solidification of a liquid film supported by surface tension between two silicon filaments, called dendrites, which border the edges of the growing strip. The ribbon can be propagated indefinitely by replenishing the liquid silicon as it is transformed to crystal. The dendritic web process has several advantages for achieving low cost, high efficiency solar cells. These advantages are discussed.

Continuous tuneable droplet ejection via pulsed surface acoustic wave jetting.

PubMed

Castro, Jasmine O; Ramesan, Shwathy; Rezk, Amgad R; Yeo, Leslie Y

2018-05-30

We report a miniaturised platform for continuous production of single or multiple liquid droplets with diameters between 60 and 500 μm by interfacing a capillary-driven self-replenishing liquid feed with pulsed excitation of focussed surface acoustic waves (SAWs). The orifice-free operation circumvents the disadvantages of conventional jetting systems, which are often prone to clogging that eventuates in rapid degradation of the operational performance. Additionally, we show the possibility for flexibly tuning the ejected droplet size through the pulse width duration, thus avoiding the need for a separate device for every different droplet size required, as is the case for systems in which the droplet size is set by nozzles and orifices, as well as preceding ultrasonic jetting platforms where the droplet size is controlled by the operating frequency. Further, we demonstrate that cells can be jetted and hence printed onto substrates with control over the cell density within the droplets down to single cells. Given that the jetting does not lead to significant loss to the cell's viability or ability to proliferate, we envisage that this versatile jetting method can potentially be exploited with further development for cell encapsulation, dispensing and 3D bioprinting applications.

Studies with the USF/NASA toxicity screening test method - Exercise wheels and oxygen replenishment

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Cumming, H. J.

1977-01-01

Continuing efforts to improve the University of San Francisco/NASA toxicity screening test method have included the addition of exercise wheels to provide a different measure of incapacitation, and oxygen replenishment to offset any effect of oxygen depletion by the test animals. The addition of exercise wheels limited the number of animals in each test and doubled the required number of tests without any significant improvement in reproducibility. Oxygen replenishment appears to have an effect on survival in the last 5 minutes of the 30-minute test, but the effect is expected to be similar for most materials.

Suboptimal and optimal order policies for fixed and varying replenishment interval with declining market

NASA Astrophysics Data System (ADS)

Yu, Jonas C. P.; Wee, H. M.; Yang, P. C.; Wu, Simon

2016-06-01

One of the supply chain risks for hi-tech products is the result of rapid technological innovation; it results in a significant decline in the selling price and demand after the initial launch period. Hi-tech products include computers and communication consumer's products. From a practical standpoint, a more realistic replenishment policy is needed to consider the impact of risks; especially when some portions of shortages are lost. In this paper, suboptimal and optimal order policies with partial backordering are developed for a buyer when the component cost, the selling price, and the demand rate decline at a continuous rate. Two mathematical models are derived and discussed: one model has the suboptimal solution with the fixed replenishment interval and a simpler computational process; the other one has the optimal solution with the varying replenishment interval and a more complicated computational process. The second model results in more profit. Numerical examples are provided to illustrate the two replenishment models. Sensitivity analysis is carried out to investigate the relationship between the parameters and the net profit.

Advanced dendritic web growth development and development of single-crystal silicon dendritic ribbon and high-efficiency solar cell program

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.

1986-01-01

Efforts to demonstrate that the dendritic web technology is ready for commercial use by the end of 1986 continues. A commercial readiness goal involves improvements to crystal growth furnace throughput to demonstrate an area growth rate of greater than 15 sq cm/min while simultaneously growing 10 meters or more of ribbon under conditions of continuous melt replenishment. Continuous means that the silicon melt is being replenished at the same rate that it is being consumed by ribbon growth so that the melt level remains constant. Efforts continue on computer thermal modeling required to define high speed, low stress, continuous growth configurations; the study of convective effects in the molten silicon and growth furnace cover gas; on furnace component modifications; on web quality assessments; and on experimental growth activities.

Advanced Czochralski silicon growth technology for photovoltaic modules

NASA Technical Reports Server (NTRS)

Daud, T.; Kachare, A. H.

1982-01-01

Several economic analyses had indicated that large-diameter, multiple ingot growth using a single crucible with melt replenishment would be required for Cz growth to be economically viable. Based on the results of these analyses, two liquid and two solid feed melt replenishment approaches were initiated. The sequential solid feed melt replenishment approach, which demonstrated elements of technical feasibility is described in detail in this paper. Growth results of multiple ingots (10-cm-diameter, totaling 100 kg; and 15-cm-diameter, totaling 150 kg weight per crucible) are presented. Solar cells were fabricated and analyzed to evaluate the effects of structure and chemical purities as a result of multiple growth. The results indicate that, with semiconductor-grade silicon, feedstock impurity build-up does not seem to degrade cell performance. For polycrystalline cells, the average efficiencies are 15 to 25% lower than those of single crystalline cells. Concerns regarding single crystal yields, crucible quality and growth speed are indicated, and present status and future research thrusts are also discussed.

Direct molecular diffusion and micro-mixing for rapid dewatering of LiBr solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bigham, S; Isfahani, RN; Moghaddam, S

2014-03-01

A slow molecular diffusion rate often limits the desorption process of an absorbate molecule from a liquid absorbent. To enhance the desorption rate, the absorbent is often boiled to increase the liquid vapor interfacial area. However, the growth of bubbles generated during the nucleate boiling process still remains mass-diffusion limited. Here, it is shown that a desorption rate higher than that of boiling can be achieved, if the vapor absorbent interface is continuously replenished with the absorbate-rich solution to limit the concentration boundary layer growth. The study is conducted in a LiBr-water-solution, in which the water molecules' diffusion rate ismore » quite slow. The manipulation of the vapor solution interface concentration distribution is enabled by the mechanical confinement of the solution flow within microchannels, using a hydrophobic vapor-venting membrane and the implementation of microstructures on the flow channel's bottom wall. The microstructures stretch and fold the laminar streamlines within the solution film and produce vortices. The vortices continuously replace the concentrated solution at the vapor solution interface with the water-rich solution brought from the bottom and middle of the flow channel. The physics of the process is described using a combination of experimental and numerical studies. Published by Elsevier Ltd.« less

Microfabricated valveless devices for thermal bioreactions based on diffusion-limited evaporation.

PubMed

Wang, Fang; Yang, Ming; Burns, Mark A

2008-01-01

Microfluidic devices that reduce evaporative loss during thermal bioreactions such as PCR without microvalves have been developed by relying on the principle of diffusion-limited evaporation. Both theoretical and experimental results demonstrate that the sample evaporative loss can be reduced by more than 20 times using long narrow diffusion channels on both sides of the reaction region. In order to further suppress the evaporation, the driving force for liquid evaporation is reduced by two additional techniques: decreasing the interfacial temperature using thermal isolation and reducing the vapor concentration gradient by replenishing water vapor in the diffusion channels. Both thermal isolation and vapor replenishment techniques can limit the sample evaporative loss to approximately 1% of the reaction content.

78 FR 34687 - Self-Regulatory Organizations; NYSE MKT LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... To Amend Rule 1000-- Equities To Revise the Manner by Which the Exchange Will Phase Out the... Exchange will phase out the functionality associated with liquidity replenishment points (``LRPs'') in... Exchange filed to amend Rule 1000--Equities to provide that it would phase out the functionality associated...

The incept of ejection from a fresh Taylor cone and subsequent evolution

NASA Astrophysics Data System (ADS)

Lopez-Herrera, Jose M.; Ganan-Calvo, Alfonso

2017-11-01

Within a certain range of applied voltages, a pendant drop suddenly subject to an intense electric field develops a cusp from which a fast liquid ligament issues. The incept of this process has common roots with other related phenomena like the Worthington jets, the jet issued after surface bubble bursting or the impact of a drop on a liquid pool. This is experimentally and numerically demonstrated. However, given the electrohydrodynamic nature of the driver in the formation of a Taylor cone, a number of electrokinetic processes take place in the rapid tapering flow, whose characteristic times should be carefully compared to the ones of the flow. As a result, universal scaling laws for the size and charge of the top drop have been obtained. Subsequently, sustaining the applied electric field, the ejection continues and the issuing liquid ligament releases a train of droplets of varying size and charge. Under appropriate conditions and if the liquid suctioned by the electric field is replenished, the system reaches a (quasi)steady state asymptotically. The degree of compliance of the size and charge of those subsequent droplets with previously proposed scaling laws of steady Taylor cone-jets has been studied. Computational code Gerris and an extended electrokinetic module is used. This work was supported by the Ministerio de Economia y Competitividad, Plan Estatal 2013-2016 Retos, project DPI2016-78887-C3-1-R.

Modeling of replenishment of sediments on a water-worked gravel bed channel

NASA Astrophysics Data System (ADS)

Juez, Carmelo; Battisacco, Elena; Schleiss, Anton J.; Franca, Mário J.

2016-04-01

The presence of dams causes a sediment deficit downstream. Hence, the surface structure of the riverbeds is altered by this interruption in the sediment continuity and The presence of dams causes a sediment deficit downstream. The surface structure of the riverbed is altered by this interruption in the sediment continuity and becoming water-worked. The main morphological effects verified in these cases are thus the generation of armored layers, bank instability, riverbed incision, changes in the channel width and coarsening of the bed particles. These results impact on the riverbed topographic variability and structure of the bedforms. Surface complexity is thus reduced with further ecological implications. The lack of fine material and surface complexity leads to the loss of aquatic and riparian habitats, limiting the possibilities for fish spawning. Nowadays, the revitalization of disturbed river reaches forms an integral part of river management. Sediment transport and associated channel morphology are understood as key processes for recreating and maintaining aquatic ecosystems. For this purpose several replenishment techniques have been considered in order to supply sediments lacking in the downstream reaches. The replenishment techniques can be seen as a pulse-like addition of sedimentary material that initially disturbs the channel. In this work, the response of the flow to the complementary material which is added in the channel is studied by means of the 2D shallow water equations in combination with the Exner equation. The numerical scheme is built by means of a weakly-coupled treatment between the hydrodynamic and morphodynamic equations leading to an efficient and robust solution. Computational outcomes are compared with experimental data obtained from several replenishment configurations studied in the laboratory. The results are analyzed by means of: (i) temporal evolution of the material spreading, (ii) occupational ratio along the channel which is the area percentage that is covered by the replenishment material, (iii) travel distance of the center of the pulse mass and (iv) effect of the bed fining in the bed shear stress. The results of these experiments assist in further evaluating how water-worked gravel bed channels evolve with artificial replenishment of sediments. This work was funded by the ITN-Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme FP7-PEOPLE-2013-ITN under REA grant agreement n_607394-SEDITRANS. The sediment replenishment experiments were funded by FOEN (Federal Office for the Environment, Switzerland).

Social Work Continuing Education: Current Issues and Future Direction

ERIC Educational Resources Information Center

Kurzman, Paul A.

2016-01-01

Continuing education is arising as an area of rapid growth and increased attention in the social work profession. Conceptually, the impetus and focus are on the promotion of the principles of lifelong learning and professional replenishment; but pragmatically, the driving force has been the virtually universal requirement of continuing education…

Biofuels: What Are They and How Can They Improve Practical Work and Discussions?

ERIC Educational Resources Information Center

MacLean, Tristan

2014-01-01

This article looks at the potential of bioenergy as a replacement for fossil fuels, the cutting-edge research being undertaken by scientists, and classroom resources available for teaching this topic. There is currently a large programme of scientific research aiming to develop advanced biofuels (replenishable liquid biofuels from non-food plants,…

Thermal Analysis of Cryogenic Hydrogen Liquid Separator

NASA Technical Reports Server (NTRS)

Congiardo, Jared F.; Fortier, Craig R. (Editor)

2014-01-01

During launch for the new Space Launch System (SLS) liquid hydrogen is bleed through the engines during replenish, pre-press, and extended pre-press to condition the engines prior to launch. The predicted bleed flow rates are larger than for the shuttle program. A consequence of the increased flow rates is having liquif hydrogen in the vent system, which the facilities was never designed to handle. To remedy the problem a liquid separator is being designed in the system to accumulated the liquid propellant and protect the facility flare stack (which can only handle gas). The attached document is a presentation of the current thermalfluid analysis performed for the separator and will be presented at the Thermal and Fluid Analysis Workshop (NASA workshop) next week in Cleveland, Ohio.

Automated Liquid-Level Control of a Nutrient Reservoir for a Hydroponic System

NASA Technical Reports Server (NTRS)

Smith, Boris; Asumadu, Johnson A.; Dogan, Numan S.

1997-01-01

A microprocessor-based system for control of the liquid level of a nutrient reservoir for a plant hydroponic growing system has been developed. The system uses an ultrasonic transducer to sense the liquid level or height. A National Instruments' Multifunction Analog and Digital Input/Output PC Kit includes NI-DAQ DOS/Windows driver software for an IBM 486 personal computer. A Labview Full Development system for Windows is the graphical programming system being used. The system allows liquid level control to within 0.1 cm for all levels tried between 8 and 36 cm in the hydroponic system application. The detailed algorithms have been developed and a fully automated microprocessor based nutrient replenishment system has been described for this hydroponic system.

On the risks from sediment and overlying water by replenishing urban landscape ponds with reclaimed wastewater.

PubMed

Ao, Dong; Chen, Rong; Wang, Xiaochang C; Liu, Yanzheng; Dzakpasu, Mawuli; Zhang, Lu; Huang, Yue; Xue, Tao; Wang, Nan

2018-05-01

The extensive use of reclaimed wastewater (RW) as a source of urban landscape pond replenishment, stimulated by the lack of surface water (SW) resources, has raised public concern. Greater attention should be paid to pond sediments, which act as 'sinks' and 'sources' of contaminants to the overlying pond water. Three ponds replenished with RW (RW ponds) in three Chinese cities were chosen to investigate 22 indices of sediment quality in four categories: eutrophication, heavy metal, ecotoxicity and pathogens risk. RW ponds were compared with other ponds of similar characteristics in the same cities that were replenished with SW (SW ponds). Our results show a strong impact of RW to the eutrophication and pathogenic risks, which are represented by organic matter, water content, total nitrogen, total phosphorus and phosphorus fractions, and pathogens. In particular, total phosphorus concentrations in the RW pond sediments were, on average, 50% higher than those of SW ponds. Moreover, the content of phosphorus, extracted by bicarbonate/dithionite (normally represented by BD-P) and NaOH (NaOH-P), were 2.0- and 2.83-times higher in RW ponds, respectively. For pathogens, the concentrations of norovirus and rotavirus in RW pond sediments were, on average, 0.52 and 0.30- log times those of SW ponds. The duration of RW replenishment was proved to have a marked impact on the eutrophication and pathogens risks from sediments. The continued use of RW for replenishment increases the eutrophication risk, and the pathogens risk, especially by viral pathogens, becomes greater. Copyright © 2018 Elsevier Ltd. All rights reserved.

76 FR 40410 - Self-Regulatory Organizations; NYSE Amex LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... the investment bank syndicate the night before the first day of trading, to determine the LRP value... During the First Day of Trading of an Initial Public Offering on the Exchange July 1, 2011. Pursuant to... for a different liquidity replenishment point (``LRP'') value range during the first day of trading of...

76 FR 40413 - Self-Regulatory Organizations; New York Stock Exchange LLC; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... the investment bank syndicate the night before the first day of trading, to determine the LRP value... Point Value Range During the First Day of Trading of an Initial Public Offering on the Exchange July 1... for a different liquidity replenishment point (``LRP'') value range during the first day of trading of...

76 FR 14699 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing of Amendment No. 3...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-17

... rule change.\\10\\ The Commission is publishing this notice and order to solicit comments on Amendment No... securities. Under this proposal, Nasdaq would suspend trading in a security if a trade in that security is... Volatility Guard is similar in purpose to the Liquidity Replenishment Points (``LRPs'') rules that currently...

Closure device for lead-acid batteries

DOEpatents

Ledjeff, Konstantin

1983-01-01

A closure device for lead-acid batteries includes a filter of granulated activated carbon treated to be hydrophobic combined with means for preventing explosion of emitted hydrogen and oxygen gas. The explosion prevention means includes a vertical open-end tube within the closure housing for maintaining a liquid level above side wall openings in an adjacent closed end tube. Gases vent from the battery through a nozzle directed inside the closed end tube against an impingement surface to remove acid droplets. The gases then flow through the side wall openings and the liquid level to quench any possible ignition prior to entering the activated carbon filter. A wick in the activated carbon filter conducts condensed liquid back to the closure housing to replenish the liquid level limited by the open-end tube.

Low cost solar array project. Cell and module formation research area. Process research of non-CZ silicon material

NASA Technical Reports Server (NTRS)

1983-01-01

Liquid diffusion masks and liquid dopants to replace the more expensive CVD SiO2 mask and gaseous diffusion processes were investigated. Silicon pellets were prepared in the silicon shot tower; and solar cells were fabricated using web grown where the pellets were used as a replenishment material. Verification runs were made using the boron dopant and liquid diffusion mask materials. The average of cells produced in these runs was 13%. The relationship of sheet resistivity, temperature, gas flows, and gas composition for the diffusion of the P-8 liquid phosphorus solution was investigated. Solar cells processed from web grown from Si shot material were evaluated, and results qualified the use of the material produced in the shot tower for web furnace feed stock.

Development of processes for the production of low cost silicon dendritic web for solar cells

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Skutch, M. E.; Driggers, J. M.; Hill, F. E.

1980-01-01

High area output rates and continuous, automated growth are two key technical requirements for the growth of low-cost silicon ribbons for solar cells. By means of computer-aided furnace design, silicon dendritic web output rates as high as 27 sq cm/min have been achieved, a value in excess of that projected to meet a $0.50 per peak watt solar array manufacturing cost. The feasibility of simultaneous web growth while the melt is replenished with pelletized silicon has also been demonstrated. This step is an important precursor to the development of an automated growth system. Solar cells made on the replenished material were just as efficient as devices fabricated on typical webs grown without replenishment. Moreover, web cells made on a less-refined, pelletized polycrystalline silicon synthesized by the Battelle process yielded efficiencies up to 13% (AM1).

Assessment of the performance of numerical modeling in reproducing a replenishment of sediments in a water-worked channel

NASA Astrophysics Data System (ADS)

Juez, C.; Battisacco, E.; Schleiss, A. J.; Franca, M. J.

2016-06-01

The artificial replenishment of sediment is used as a method to re-establish sediment continuity downstream of a dam. However, the impact of this technique on the hydraulics conditions, and resulting bed morphology, is yet to be understood. Several numerical tools have been developed during last years for modeling sediment transport and morphology evolution which can be used for this application. These models range from 1D to 3D approaches: the first being over simplistic for the simulation of such a complex geometry; the latter requires often a prohibitive computational effort. However, 2D models are computationally efficient and in these cases may already provide sufficiently accurate predictions of the morphology evolution caused by the sediment replenishment in a river. Here, the 2D shallow water equations in combination with the Exner equation are solved by means of a weak-coupled strategy. The classical friction approach considered for reproducing the bed channel roughness has been modified to take into account the morphological effect of replenishment which provokes a channel bed fining. Computational outcomes are compared with four sets of experimental data obtained from several replenishment configurations studied in the laboratory. The experiments differ in terms of placement volume and configuration. A set of analysis parameters is proposed for the experimental-numerical comparison, with particular attention to the spreading, covered surface and travel distance of placed replenishment grains. The numerical tool is reliable in reproducing the overall tendency shown by the experimental data. The effect of fining roughness is better reproduced with the approach herein proposed. However, it is also highlighted that the sediment clusters found in the experiment are not well numerically reproduced in the regions of the channel with a limited number of sediment grains.

Experimental evidence for modifying the current physical model for ice accretion on aircraft surfaces

NASA Technical Reports Server (NTRS)

Olsen, W.; Walker, E.

1986-01-01

Closeup movies, still photographs, and other experimental data suggest that the current physical model for ice accretion needs significant modification. At aircraft airspeeds there was no flow of liquid over the surface of the ice after a short initial flow, even at barely subfreezing temperatures. Instead, there were very large stationary drops on the ice surface that lose water from their bottoms by freezing and replenish their liquid by catching the microscopic cloud droplets. This observation disagrees with the existing physical model, which assumes there is a thin liquid film continuously flowing over the ice surface. With no such flow, the freezing-fraction concept of the model fails when a mass balance is performed on the surface water. Rime ice does, as the model predicts, form when the air temperature is low enough to cause the cloud droplets to freeze almost immediately on impact. However, the characteristic shapes of horn-glaze ice or rime ice are primarily caused by the ice shape affecting the airflow locally and consequently the droplet catch and the resulting ice shape. Ice roughness greatly increases the heat transfer coefficient, stops the movement of drops along the surface, and may also affect the airflow initially and thereby the droplet catch. At high subreezing temperatures the initial flow and shedding of surface drops have a large effect on the ice shape. At the incipient freezing limit, no ice forms.

Compositional evolution of the zoned calcalkaline magma chamber of Mount Mazama, Crater Lake, Oregon

USGS Publications Warehouse

Bacon, C.R.; Druitt, T.H.

1988-01-01

The climactic eruption of Mount Mazama has long been recognized as a classic example of rapid eruption of a substantial fraction of a zoned magma body. Increased knowledge of eruptive history and new chemical analyses of ???350 wholerock and glass samples of the climactic ejecta, preclimactic rhyodacite flows and their inclusions, postcaldera lavas, and lavas of nearby monogenetic vents are used here to infer processes of chemical evolution of this late Pleistocene - Holocene magmatic system. The 6845??50 BP climactic eruption vented ???50 km3 of magma to form: (1) rhyodacite fall deposit; (2) welded rhyodacite ignimbrite; and (3) lithic breccia and zoned ignimbrite, these during collapse of Crater Lake caldera. Climactic ejecta were dominantly homogeneous rhyodacite (70.4??0.3% SiO2), followed by subordinate andesite and cumulate scoriae (48-61% SiO2). The gap in wholerock composition reflects mainly a step in crystal content because glass compositions are virtually continuous. Two types of scoriae are distinguished by different LREE, Rb, Th, and Zr, but principally by a twofold contrast in Sr content: High-Sr (HSr) and low-Sr (LSr) scoriae. HSr scoriae were erupted first. Trace element abundances indicate that HSr and LSr scoriae had different calcalkaline andesite parents; basalt was parental to some mafic cumulate scoriae. Parental magma compositions reconstructed from scoria wholerock and glass data are similar to those of inclusions in preclimactic rhyodacites and of aphyric lavas of nearby monogenetic vents. Preclimactic rhyodacite flows and their magmatic inclusions give insight into evolution of the climactic chamber. Evolved rhyodacite flows containing LSr andesite inclusions were emplaced between ???30000 and ???25000 BP. At 7015??45 BP, the Llao Rock vent produced a zoned rhyodacite pumice fall, then rhyodacite lava with HSr andesite inclusions. The Cleetwood rhyodacite flow, emplaced immediately before the climactic eruption and compositionally identical to climactic rhyodacite (volatile-free), contains different HSr inclusions from Llao Rock. The change from LSr to HSr inclusions indicates replenishment of the chamber with andesite magma, perhaps several times, in the latest Pleistocene to early Holocene. Modeling calculations and wholerock-glass relations suggest than: (1) magmas were derived mainly by crystallization differentiation of andesite liquid; (2) evolved preclimactic rhyodacite probably was derived from LSr andesite; (3) rhyodacites contain a minor component of partial melt from wall rocks, and (4) climactic and compositionally similar rhyodacites probably formed by mixing of evolved rhyodacite with HSr derivative liquid(s) after replenishment of the chamber with HSr andesite magma. Density considerations permit a model for growth and evolution of the chamber in which andesite recharge magma ponded repeatedly between cumulates and rhyodacite magma. Convective cooling of this andesite resulted in rapid crystallization and upward escape of buoyant derivative liquid which mixed with overlying, convecting rhyodacite. The evolved rhyodacites were erupted early in the chamber's history and(or) near its margins. Postcaldera andesite lavas may be hybrids composed of LSr cumulates mixed with remnant climactic rhyodacite. Younger postcaldera rhyodacite probably formed by fractionation of similar andesite and assimilation of partial melts of wallrocks. Uniformity of climactic rhyodacite suggests homogeneous silicic ejecta from other volcanoes resulted from similar replenishment-driven convective mixing. Calcalkaline pluton compositions and their internal zonation can be interpreted in terms of the Mazama system frozen at various times in its history. ?? 1988 Springer-Verlag.

Transdermal Delivery of Iron Using Soluble Microneedles: Dermal Kinetics and Safety.

PubMed

Modepalli, Naresh; Shivakumar, H Nanjappa; McCrudden, Maeliosa T C; Donnelly, Ryan F; Banga, Ajay; Murthy, S Narasimha

2016-03-01

Currently, the iron compounds are administered via oral and parenteral routes in patients of all ages, to treat iron deficiency. Despite continued efforts to supplement iron via these conventional routes, iron deficiency still remains the most prevalent nutritional disorder all over the world. Transdermal replenishment of iron is a novel, potential approach of iron replenishment. Ferric pyrophosphate (FPP) was found to be a suitable source of iron for transdermal replenishment. The safety of FPP was assessed in this project by challenging the dermal fibroblast cells with high concentration of FPP. The cell viability assay and reactive oxygen species assay were performed. The soluble microneedle array was developed, incorporated with FPP and the kinetics of free iron in the skin; extracellular fluid following dermal administration of microneedle array was investigated in hairless rats. From the cell based assays, FPP was selected as one of the potential iron sources for transdermal delivery. The microneedles were found to dissolve in the skin fluid within 3 hours of administration. The FPP concentration in the dermal extracellular fluid declined after complete dissolution of the microneedle array. Overall, the studies demonstrated the safety of FPP for dermal delivery and the feasibility of soluble microneedle approach for transdermal iron replenishment therapy. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Optimizing Multi-Product Multi-Constraint Inventory Control Systems with Stochastic Replenishments

NASA Astrophysics Data System (ADS)

Allah Taleizadeh, Ata; Aryanezhad, Mir-Bahador; Niaki, Seyed Taghi Akhavan

Multi-periodic inventory control problems are mainly studied employing two assumptions. The first is the continuous review, where depending on the inventory level orders can happen at any time and the other is the periodic review, where orders can only happen at the beginning of each period. In this study, we relax these assumptions and assume that the periodic replenishments are stochastic in nature. Furthermore, we assume that the periods between two replenishments are independent and identically random variables. For the problem at hand, the decision variables are of integer-type and there are two kinds of space and service level constraints for each product. We develop a model of the problem in which a combination of back-order and lost-sales are considered for the shortages. Then, we show that the model is of an integer-nonlinear-programming type and in order to solve it, a search algorithm can be utilized. We employ a simulated annealing approach and provide a numerical example to demonstrate the applicability of the proposed methodology.

Pellet Feed for Dendritic-Web Growth

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Skutch, M. E.; Mchugh, J. P.

1983-01-01

Melt replenishment system sustains continuous growth of silicon dentritic web for several days. Substantially increases size of batch, limited mainly by level of impurities and life of crucible. Silicon pellets automatically added to crucible sustain crystal growth for days.

System for venting gas from a liquid storage tank

NASA Astrophysics Data System (ADS)

Dugan, Regina E.

1989-07-01

Gas is vented from a non-cryogenic liquid storage tank while discharging pressurized liquid from a tube into the tank through a plurality of inclined jets, circumferentially spaced about an end of a vent tube positioned within the tube. Each jet is directed toward a central axis of the vent tube, such that the end of the vent tube receives gas from the vessel passing between individual jetstreams, which in combination form a conical shaped barrier to liquid droplets which would otherwise also pass to the vent tube and out the tank. Gas is thus vented through the central tube while pressurized liquid flows in an axially opposite direction in the annulus between the inner vent tube and the outer liquid tube. The system of the present invention is prarticularly well suited for venting gas from a tank being replenished with liquid at a zero or near zero gravity environment. A screen-type liquid acquisition device employing surface tension is provided for withdrawing substantially liquid from the tank. The withdrawn liquid may be resupplied to the liquid tube under pressure supplied by a circulating pump, thereby releasing substantially only gas from the storage tank to reduce the pressure in the tank.

Reactive uptake of NO3 by liquid and frozen organics

NASA Astrophysics Data System (ADS)

Moise, T.; Talukdar, R. K.; Frost, G. J.; Fox, R. W.; Rudich, Y.

2002-01-01

The reactive uptake of the NO3 radical by liquid and frozen organics was studied in a rotating wall flow tube coupled to a White cell. The organic liquids used included alkanes, alkenes, an alcohol, and carboxylic acids with conjugated and nonconjugated unsaturated bonds.. The reactive uptake coefficients, γ, of NO3 on n-hexadecane, 1-octadecene, 1-hexadecene, cis + trans 7-tetradecene, n-octanoic acid, 2,2,4,4,6,8,8 heptamethyl nonane, 1-octanol, cis, trans 9,11 and 10,12 octadecadienoic acid, cis-9, cis-12 octadecadienoic acid were determined. The reactive uptake coefficients measured with the organic liquids varied from 1.4 × 10-3 to 1.5 × 10-2. The uptake coefficients of NO3 by n-hexadecane and n-octanoic acid decreased by a factor of ~5 upon freezing. This behavior is explained by reaction occurring in the bulk of the organic liquid as well as on the surface. For the rest of the compounds the change in values of γ upon freezing of the liquids was within the experimental uncertainty. This is attributed to predominant uptake of NO3 by the top few molecular surface layers of the organic substrate and continuous replenishment of the surface layer by evaporation and/or mobility of the surface. These conclusions are corroborated by estimation of the diffuso-reactive length and solubility constant of NO3 in these liquids. The reactivity of NO3 with the organic surfaces is shown to correlate well with the known gas-phase chemistry of NO3. The effect on the atmospheric chemistry of the NO3 radical due to its interaction with organic aerosols is studied using an atmospheric box model applying realistic atmospheric scenarios. The inclusion of NO3 uptake on organic aerosol can decrease the NO3 lifetime by 10% or more.

A Joint Replenishment Inventory Model with Lost Sales

NASA Astrophysics Data System (ADS)

Devy, N. L.; Ai, T. J.; Astanti, R. D.

2018-04-01

This paper deals with two items joint replenishment inventory problem, in which the demand of each items are constant and deterministic. Inventory replenishment of items is conducted periodically every T time intervals. Among of these replenishments, joint replenishment of both items is possible. It is defined that item i is replenished every ZiT time intervals. Replenishment of items are instantaneous. All of shortages are considered as lost sales. The maximum allowance for lost sales of item i is Si. Mathematical model is formulated in order to determining the basic time cycle T, replenishment multiplier Zi , and maximum lost sales Si in order to minimize the total cost per unit time. A solution methodology is proposed for solve the model and a numerical example is provided for demonstrating the effectiveness of the proposed methodology.

[Introduction of a bar coding pharmacy stock replenishment system in a prehospital emergency medical unit: economical impact].

PubMed

Dupuis, S; Fecci, J-L; Noyer, P; Lecarpentier, E; Chollet-Xémard, C; Margenet, A; Marty, J; Combes, X

2009-01-01

To assess economical impact after introduction of a bar coding pharmacy stock replenishment system in a prehospital emergency medical unit. Observational before and after study. A computer system using specific software and bare-code technology was introduced in the pre hospital emergency medical unit (Smur). Overall activity and costs related to pharmacy were recorded annually during two periods: the first 2 years period before computer system introduction and the second one during the 4 years following this system installation. The overall clinical activity increased by 10% between the two periods whereas pharmacy related costs continuously decreased after the start of pharmacy management computer system use. Pharmacy stock management was easier after introduction of the new stock replenishment system. The mean pharmacy related cost of one patient management was 13 Euros before and 9 Euros after the introduction of the system. The overall cost savings during the studied period was calculated to reach 134,000 Euros. The introduction of a specific pharmacy management computer system allowed to do important costs savings in a prehospital emergency medical unit.

Algivore or Phototroph? Plakobranchus ocellatus (Gastropoda) Continuously Acquires Kleptoplasts and Nutrition from Multiple Algal Species in Nature

PubMed Central

Maeda, Taro; Hirose, Euichi; Chikaraishi, Yoshito; Kawato, Masaru; Takishita, Kiyotaka; Yoshida, Takao; Verbruggen, Heroen; Tanaka, Jiro; Shimamura, Shigeru; Takaki, Yoshihiro; Tsuchiya, Masashi; Iwai, Kenji; Maruyama, Tadashi

2012-01-01

The sea slug Plakobranchus ocellatus (Sacoglossa, Gastropoda) retains photosynthetically active chloroplasts from ingested algae (functional kleptoplasts) in the epithelial cells of its digestive gland for up to 10 months. While its feeding behavior has not been observed in natural habitats, two hypotheses have been proposed: 1) adult P. ocellatus uses kleptoplasts to obtain photosynthates and nutritionally behaves as a photoautotroph without replenishing the kleptoplasts; or 2) it behaves as a mixotroph (photoautotroph and herbivorous consumer) and replenishes kleptoplasts continually or periodically. To address the question of which hypothesis is more likely, we examined the source algae for kleptoplasts and temporal changes in kleptoplast composition and nutritional contribution. By characterizing the temporal diversity of P. ocellatus kleptoplasts using rbcL sequences, we found that P. ocellatus harvests kleptoplasts from at least 8 different siphonous green algal species, that kleptoplasts from more than one species are present in each individual sea slug, and that the kleptoplast composition differs temporally. These results suggest that wild P. ocellatus often feed on multiple species of siphonous algae from which they continually obtain fresh chloroplasts. By estimating the trophic position of wild and starved P. ocellatus using the stable nitrogen isotopic composition of amino acids, we showed that despite the abundance of kleptoplasts, their photosynthates do not contribute greatly to the nutrition of wild P. ocellatus, but that kleptoplast photosynthates form a significant source of nutrition for starved sea slugs. The herbivorous nature of wild P. ocellatus is consistent with insights from molecular analyses indicating that kleptoplasts are frequently replenished from ingested algae, leading to the conclusion that natural populations of P. ocellatus do not rely on photosynthesis but mainly on the digestion of ingested algae. PMID:22848693

78 FR 4133 - Procurement List; Proposed Additions and Deletion

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-18

... specific tasks including preparation of menu boards, table bussing service, guest flow rate, service of food, replenishing of food, unloading, storing, and shelving of supplies, food preparation, cashier... the event of contingency, perform all required tasks to include cooking to ensure continued service...

Photocathode device that replenishes photoemissive coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moody, Nathan A.; Lizon, David C.

2016-06-14

A photocathode device may replenish its photoemissive coating to replace coating material that desorbs/evaporates during photoemission. A linear actuator system may regulate the release of a replenishment material vapor, such as an alkali metal, from a chamber inside the photocathode device to a porous cathode substrate. The replenishment material deposits on the inner surface of a porous membrane and effuses through the membrane to the outer surface, where it replenishes the photoemissive coating. The rate of replenishment of the photoemissive coating may be adjusted using the linear actuator system to regulate performance of the photocathode device during photoemission. Alternatively, themore » linear actuator system may adjust a plasma discharge gap between a cartridge containing replenishment material and a metal grid. A potential is applied between the cartridge and the grid, resulting in ejection of metal ions from the cartridge that similarly replenish the photoemissive coating.« less

Effects of beach replenishment on intertidal invertebrates: A 15-month, eight beach study.

NASA Astrophysics Data System (ADS)

Wooldridge, Tyler; Henter, Heather J.; Kohn, Joshua R.

2016-06-01

Beach replenishment is an increasingly popular means to remediate coastal erosion, but no consensus exists regarding how long replenishment affects sandy beach intertidal invertebrates, key components of beach ecosystems. We monitored the intertidal invertebrate community for fifteen months following a replenishment project at eight beaches, each with replenished and control sections, across San Diego County. Nearly all taxa showed major declines in abundance immediately following replenishment. Populations of talitrid amphipods and the bean clam Donax gouldii recovered within one year, sooner than in previous studies. On some beaches, populations of the mole crab Emerita analoga bloomed four months after replenishment and were more numerous on replenished portions of beaches at that time. Mole crab populations subsequently declined and no longer differed by treatment. The polychaete community, composed of Scolelepis sp. and several other numerically important taxa, showed a strong replenishment-induced reduction in abundance that persisted through the end of the study. The large negative effect of replenishment on polychaetes, coupled with their overall importance to the invertebrate community, resulted in a more than twofold reduction in overall invertebrate abundance on replenished beaches at 15 months. Such reductions may have far reaching consequences for sandy beach ecosystems, as community declines can reduce prey availability for shorebirds and fish. As this and other recent studies have revealed longer times for the recovery of intertidal invertebrates than previously observed, longer study periods and more cautious estimates regarding the magnitude, variability, and duration of impacts of beach replenishment for management decision-making are warranted.

41 CFR 109-27.102-50 - Systems contracting.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Systems contracting. 109... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102-50 Systems contracting. Systems contracting may...

41 CFR 109-27.102-50 - Systems contracting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Systems contracting. 109... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102-50 Systems contracting. Systems contracting may...

Spiral vane bioreactor

NASA Technical Reports Server (NTRS)

Morrison, Dennis R. (Inventor)

1991-01-01

A spiral vane bioreactor of a perfusion type is described in which a vertical chamber, intended for use in a microgravity condition, has a central rotating filter assembly and has flexible membranes disposed to rotate annularly about the filter assembly. The flexible members have end portions disposed angularly with respect to one another. A fluid replenishment medium is input from a closed loop liquid system to a completely liquid filled chamber containing microcarrier beads, cells and a fluid medium. Output of spent medium is to the closed loop. In the closed loop, the output and input parameters are sensed by sensors. A manifold permits recharging of the nutrients and pH adjustment. Oxygen is supplied and carbon dioxide and bubbles are removed and the system is monitored and controlled by a microprocessor.

Evaluation of an anaerobic digestion system for processing CELSS crop residues for resource recovery

NASA Astrophysics Data System (ADS)

Strayer, R. F.; Finger, B. W.; Alazraki, M. P.

1997-01-01

Three bioreactors, connected in series, were used to process CELSS potato residues for recovery of resources. The first stage was an anaerobic digestor (8 L working volume; cow rumen contents inoculum; fed-batch; 8 day retention time; feed rate 25 gdw day^-1) that converted 33% of feed (dry weight loss) to CO_2 and ``volatile fatty acids'' (vfa, 83:8:8 mmolar ratio acetic:propionic:butyric). High nitrate-N in the potato residue feed was absent in the anaerobic effluent, with a high portion converted to NH_4^+-N and the remainder unaccounted and probably lost to denitrification and NH_4^+ volatilization. Liquid anaerobic effluent was fed to an aerobic, yeast biomass production vessel (2 L volume; Candida ingens inoculum; batch [pellicle] growth; 2 day retention time) where the VFAs and some NH_4^+-N were converted into yeast biomass. Yeast yields accounted for up to 8% of potato residue fed into the anaerobic bioreactor. The third bioreactor (0.5 L liquid working volume; commercial nitrifier inoculum; packed-bed biofilm; continuous yeast effluent feed; recirculating; constant volume; 2 day hydraulic retention time) was used to convert successfully the remaining NH_4^+-N into nitrate-N (preferred form of N for CELSS crop production) and to remove the remaining degradable soluble organic carbon. Effluents from the last two stages were used for partial replenishment of minerals for hydroponic potato production.

Evaluation of an Anaerobic Digestion System for Processing CELSS Crop Residues for Resource Recovery

NASA Technical Reports Server (NTRS)

Strayer, R. F.; Finger, B. W.; Alazraki, M. P.

1997-01-01

Three bioreactors, connected in series, were used to process CELSS potato residues for recovery of resources. The first stage was an anaerobic digestor (8 L working volume; cow rumen contents inoculum; fed-batch; 8 day retention time; feed rate 25 gdw/day) that converted 33% of feed (dry weight loss) to CO2 and "volatile fatty acids" (vfa, 83:8:8 mmolar ratio acetic:propionic:butyric). High nitrate-N in the potato residue feed was absent in the anaerobic effluent, with a high portion converted to NH4(+)-N and the remainder unaccounted and probably lost to denitrification and NH4(+) volatilization. Liquid anaerobic effluent was fed to an aerobic, yeast biomass production vessel (2 L volume; Candida ingens inoculum; batch [pellicle] growth; 2 day retention time) where the VFAs and some NH4(+)-N were converted into yeast biomass. Yeast yields accounted for up to 8% of potato residue fed into the anaerobic bioreactor. The third bioreactor (0.5 L liquid working volume; commercial nitrifier inoculum; packed-bed biofilm; continuous yeast effluent feed; recirculating; constant volume; 2 day hydraulic retention time) was used to convert successfully the remaining NH4(+)-N into nitrate-N (preferred form of N for CELSS crop production) and to remove the remaining degradable soluble organic carbon. Effluents from the last two stages were used for partial replenishment of minerals for hydroponic potato production.

BOLE WATER CONTENT SHOWS LITTLE SEASONAL VARIATION IN CENTURY-OLD DOUGLAS-FIR TREES

EPA Science Inventory

Purportedly, large Douglas-fir trees in the American Pacific Northwest use water stored in bole tissues to ameliorate the effects of seasonal summer drought, the water content of bole tissues being drawn down over the summer months and replenished during the winter. Continuous mo...

32 CFR 707.5 - Underway replenishment contour lights.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Underway replenishment contour lights. 707.5... RULES WITH RESPECT TO ADDITIONAL STATION AND SIGNAL LIGHTS § 707.5 Underway replenishment contour lights... underway replenishment operations, either red or blue lights at delivery-ship-deck-edge extremities. [42 FR...

32 CFR 707.5 - Underway replenishment contour lights.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 5 2014-07-01 2014-07-01 false Underway replenishment contour lights. 707.5... RULES WITH RESPECT TO ADDITIONAL STATION AND SIGNAL LIGHTS § 707.5 Underway replenishment contour lights... underway replenishment operations, either red or blue lights at delivery-ship-deck-edge extremities. [42 FR...

32 CFR 707.5 - Underway replenishment contour lights.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 5 2011-07-01 2011-07-01 false Underway replenishment contour lights. 707.5... RULES WITH RESPECT TO ADDITIONAL STATION AND SIGNAL LIGHTS § 707.5 Underway replenishment contour lights... underway replenishment operations, either red or blue lights at delivery-ship-deck-edge extremities. [42 FR...

32 CFR 707.5 - Underway replenishment contour lights.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 5 2013-07-01 2013-07-01 false Underway replenishment contour lights. 707.5... RULES WITH RESPECT TO ADDITIONAL STATION AND SIGNAL LIGHTS § 707.5 Underway replenishment contour lights... underway replenishment operations, either red or blue lights at delivery-ship-deck-edge extremities. [42 FR...

32 CFR 707.5 - Underway replenishment contour lights.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 5 2012-07-01 2012-07-01 false Underway replenishment contour lights. 707.5... RULES WITH RESPECT TO ADDITIONAL STATION AND SIGNAL LIGHTS § 707.5 Underway replenishment contour lights... underway replenishment operations, either red or blue lights at delivery-ship-deck-edge extremities. [42 FR...

Online Calibration Methods for the DINA Model with Independent Attributes in CD-CAT

ERIC Educational Resources Information Center

Chen, Ping; Xin, Tao; Wang, Chun; Chang, Hua-Hua

2012-01-01

Item replenishing is essential for item bank maintenance in cognitive diagnostic computerized adaptive testing (CD-CAT). In regular CAT, online calibration is commonly used to calibrate the new items continuously. However, until now no reference has publicly become available about online calibration for CD-CAT. Thus, this study investigates the…

Control of Nanoscale Friction on Gold in an Ionic Liquid by a Potential-Dependent Ionic Lubricant Layer

NASA Astrophysics Data System (ADS)

Sweeney, James; Hausen, Florian; Hayes, Robert; Webber, Grant B.; Endres, Frank; Rutland, Mark W.; Bennewitz, Roland; Atkin, Rob

2012-10-01

The lubricating properties of an ionic liquid on gold surfaces can be controlled through application of an electric potential to the sliding contact. A nanotribology approach has been used to study the frictional behavior of 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl) trifluorophosphate ([Py1,4]FAP) confined between silica colloid probes or sharp silica tips and a Au(111) substrate using atomic force microscopy. Friction forces vary with potential because the composition of a confined ion layer between the two surfaces changes from cation-enriched (at negative potentials) to anion-enriched (at positive potentials). This offers a new approach to tuning frictional forces reversibly at the molecular level without changing the substrates, employing a self-replenishing boundary lubricant of low vapor pressure.

A novel multi-item joint replenishment problem considering multiple type discounts.

PubMed

Cui, Ligang; Zhang, Yajun; Deng, Jie; Xu, Maozeng

2018-01-01

In business replenishment, discount offers of multi-item may either provide different discount schedules with a single discount type, or provide schedules with multiple discount types. The paper investigates the joint effects of multiple discount schemes on the decisions of multi-item joint replenishment. In this paper, a joint replenishment problem (JRP) model, considering three discount (all-unit discount, incremental discount, total volume discount) offers simultaneously, is constructed to determine the basic cycle time and joint replenishment frequencies of multi-item. To solve the proposed problem, a heuristic algorithm is proposed to find the optimal solutions and the corresponding total cost of the JRP model. Numerical experiment is performed to test the algorithm and the computational results of JRPs under different discount combinations show different significance in the replenishment cost reduction.

A simulation based approach to optimize inventory replenishment with RAND algorithm: An extended study of corrected demand using Holt's method for textile industry

NASA Astrophysics Data System (ADS)

Morshed, Mohammad Sarwar; Kamal, Mostafa Mashnoon; Khan, Somaiya Islam

2016-07-01

Inventory has been a major concern in supply chain and numerous researches have been done lately on inventory control which brought forth a number of methods that efficiently manage inventory and related overheads by reducing cost of replenishment. This research is aimed towards providing a better replenishment policy in case of multi-product, single supplier situations for chemical raw materials of textile industries in Bangladesh. It is assumed that industries currently pursue individual replenishment system. The purpose is to find out the optimum ideal cycle time and individual replenishment cycle time of each product for replenishment that will cause lowest annual holding and ordering cost, and also find the optimum ordering quantity. In this paper indirect grouping strategy has been used. It is suggested that indirect grouping Strategy outperforms direct grouping strategy when major cost is high. An algorithm by Kaspi and Rosenblatt (1991) called RAND is exercised for its simplicity and ease of application. RAND provides an ideal cycle time (T) for replenishment and integer multiplier (ki) for individual items. Thus the replenishment cycle time for each product is found as T×ki. Firstly, based on data, a comparison between currently prevailing (individual) process and RAND is provided that uses the actual demands which presents 49% improvement in total cost of replenishment. Secondly, discrepancies in demand is corrected by using Holt's method. However, demands can only be forecasted one or two months into the future because of the demand pattern of the industry under consideration. Evidently, application of RAND with corrected demand display even greater improvement. The results of this study demonstrates that cost of replenishment can be significantly reduced by applying RAND algorithm and exponential smoothing models.

Hybrid armature projectile

DOEpatents

Hawke, Ronald S.; Asay, James R.; Hall, Clint A.; Konrad, Carl H.; Sauve, Gerald L.; Shahinpoor, Mohsen; Susoeff, Allan R.

1993-01-01

A projectile for a railgun that uses a hybrid armature and provides a seed block around part of the outer surface of the projectile to seed the hybrid plasma brush. In addition, the hybrid armature is continuously vaporized to replenish plasma in a plasma armature to provide a tandem armature and provides a unique ridge and groove to reduce plasama blowby.

Building a Zoological Teaching Collection of Invertebrates Using Alcoholic Gel

ERIC Educational Resources Information Center

Mugnai, Riccardo; Barbosa, Julio Vianna; Baptista, Darcilio Fernandes

2012-01-01

Teaching collections are of great importance for science instruction at any level. There are several problems linked to the handling and curatorial management of this kind of collection. Among these is the relatively short life-span of specimens, due to the damage from continuous handling by students. Often the specimens used to replenish the…

A Drop through Time

ERIC Educational Resources Information Center

Vowell, Julie; Phillips, Marianne

2007-01-01

Did you know that the water you use today is the same water that was used millions of years ago? How is this possible? Water is continuously replenished through a naturally occurring process known as the water cycle. To help students learn about this important concept, an eight-day unit was created for fifth-grade students to explore the water…

Bioregenerative Life-Support System For Long Missions

NASA Technical Reports Server (NTRS)

Cullingford, Hatice S.

1994-01-01

Collection of four reports proposes integrated bioregenerative life-support system that sustains tens of people isolated from Earth's oxygen and sunlight. System self-sufficient for year or more; continues beyond that period with replenishment of supplies. Used in long-term spaceflights, space stations, such planet bases as those on Earth's Moon or Mars, and submarine vehicles and installations.

Hybrid armature projectile

DOEpatents

Hawke, R.S.; Asay, J.R.; Hall, C.A.; Konrad, C.H.; Sauve, G.L.; Shahinpoor, M.; Susoeff, A.R.

1993-03-02

A projectile for a railgun that uses a hybrid armature and provides a seed block around part of the outer surface of the projectile to seed the hybrid plasma brush. In addition, the hybrid armature is continuously vaporized to replenish plasma in a plasma armature to provide a tandem armature and provides a unique ridge and groove to reduce plasma blowby.

Ceramic micro-injection molded nozzles for serial femtosecond crystallography sample delivery

NASA Astrophysics Data System (ADS)

Beyerlein, K. R.; Adriano, L.; Heymann, M.; Kirian, R.; Knoška, J.; Wilde, F.; Chapman, H. N.; Bajt, S.

2015-12-01

Serial femtosecond crystallography (SFX) using X-ray Free-Electron Lasers (XFELs) allows for room temperature protein structure determination without evidence of conventional radiation damage. In this method, a liquid suspension of protein microcrystals can be delivered to the X-ray beam in vacuum as a micro-jet, which replenishes the crystals at a rate that exceeds the current XFEL pulse repetition rate. Gas dynamic virtual nozzles produce the required micrometer-sized streams by the focusing action of a coaxial sheath gas and have been shown to be effective for SFX experiments. Here, we describe the design and characterization of such nozzles assembled from ceramic micro-injection molded outer gas-focusing capillaries. Trends of the emitted jet diameter and jet length as a function of supplied liquid and gas flow rates are measured by a fast imaging system. The observed trends are explained by derived relationships considering choked gas flow and liquid flow conservation. Finally, the performance of these nozzles in a SFX experiment is presented, including an analysis of the observed background.

Magma Interactions in Rhyolite Reservoirs Caused by Injection of New Rhyolitic Liquid: Results From Analogue Modeling

NASA Astrophysics Data System (ADS)

Girard, G.; Stix, J.

2006-12-01

Recharge of magma chambers by new inputs of magma is often identified as a trigger for eruptions. However, most studies to date have been carried out on mafic to intermediate composition melts replenishing mafic to silicic reservoirs, often with large compositional differences. Here we focus on rhyolites at large silicic centers such as Yellowstone where no differentiated material other than rhyolite is erupted. We investigate the behavior of rhyolite magma intruding reservoirs of similar composition and temperature, by using analogue experiments with water/corn syrup solutions as analogue magma. The density and viscosity of these solutions range from 1130 to 1320 kg m-3 and 0.008 to 8 Pa s, respectively. The fate of the injected liquid is mainly controlled by the density difference between the injected and resident liquids. Intruding material denser than resident liquid is not able to rise into the reservoir, instead building a flat basal layer or a cone above the discharge point. No further interaction such as mixing occurs. Buoyant injected material rises vertically to the top of the reservoir, also with little interaction involving resident liquid during its ascent. The injected fluid eventually spreads at the top of the reservoir, followed by mixing with the resident phase through the entire reservoir. Variables such as injection rate and viscosity mostly influence the timing and duration of this sequence of events, without changing the final result. The presence of a basal crystal mush, modeled by adding Elvacite plastic grains of 0.15 mm diameter with a density of 1160 kg m-3, does not influence the behavior of a slightly buoyant injection; the injected fluid creates its own path through the mush, eventually rising to the top of the liquid upper part of the reservoir. At the beginning of the injection, however, the intruding liquid must establish a path through the mush. At this stage, the intruding fluid violently entrains substantial numbers of particles which travel through the liquid upper part of the reservoir together with the intruding plume. The particles then travel laterally a short distance and settle towards the mush. These experiments show that injected melt may not be easily distinguished from resident melt due to their similar compositions and mixing processes. However, the remobilization of a basal mush by intruding magma has key implications with regard to crystals in upper layers of magma reservoirs. If the crystals are erupted before settling, they will bear the imprint of strong pressure and temperature changes they have undergone during entrainment by the rising replenishing magma. These entrainment processes may be manifested by dissolution and/or overgrowth features, while the higher pressure at which the crystals first formed will be reflected by a core composition typical of deeper environments.

Nanoscale modeling for ultrathin liquid films: Spreading and coupled layering

NASA Astrophysics Data System (ADS)

Phillips, David Michael

The hard disk drive (HDD) industry is currently experiencing a compound annual growth rate of 100% for the areal density. Current production drives have an areal density of 80 Gbit in-2, and drives with an areal density of 100 Gbit in-2 have been recently demonstrated. While much of this growth has been fueled by the development of new read/write heads, some of this gain was achieved by reducing the spacing between the heads and the magnetic media. This in turn reduces the spacing at the head-disk interface (HDI). The HDI in a HDD system consists of a slider, which contains the read/write heads, flying over the disk surface on an air bearing. The current designed separation distance, or fly height, is less than 10 nm. This spacing is expected to reduce to a mere 5 nm within the next few years. With the reduced fly height, intermittent contacts at the HDI become more probable. Only a thin lubricant film of perfluoropolyether (PFPE) and a sputtered carbon overcoat on the disk surface protect the slider and the stored data from mechanical and thermal damage. The PFPE film is quite thin, with a thickness of less than 2 nm or about a monolayer of molecules. During an HDI contact, the PFPE film is considered sacrificial and is often depleted in the contact area. In order to maintain adequate protection for the disk surface, PFPE molecules from the surrounding film must replenish the depleted area. This replenishment ability directly opposes the requirement that the PFPE film must not spin-off of the disk surface due to the disk rotation rate, which is as high as 10,000 RPM in current drives. To balance the PFPE films to sufficiently meet both requirements, HDD manufacturers functionalized the endgroups of the PFPE molecules to allow some portion of the lubricant film to reversibly bond with the disk overcoat. The result is a lubricant film that has a slower replenishment but does not spin-off. The work presented here focuses on the replenishment ability of thin films of liquid PFPE. The experimental analogue of replenishment is the one-dimensional spreading analysis. PFPEs with functional endgroups demonstrated coupled molecular layering and dewetting phenomena during the spreading analysis, while PFPEs with nonfunctional endgroups did not. All of the PFPE thin films spread via a diffusive process and had diffusion coefficients that depended on the local film thickness. A theoretical analysis is presented here for both the governing equation and the disjoining pressure driving force for the PFPE thin film spreading. For PFPEs with non-functional endgroups, a reasonable analysis is performed on the diffusion coefficient for two classes of film: submonolayer and multilayer. The diffusion coefficient of PFPEs with functional endgroups are qualitatively linked to the gradient of the film disjoining pressure. To augment this theory, both lattice-based and off-lattice Monte Carlo simulations are conducted for PFPE film models. The lattice-based model shows the existence of a critical functional endgroup interaction strength. It is also used to study the break-up of molecular layers for a spreading film via a fractal analysis. The off-lattice model is used to calculate the anisotropic pressure tensor for the model PFPE thin film and subsequently the film disjoining pressure. The model also qualitatively analyzes of the self diffusion in the film.

[The study of medical supplies automation replenishment algorithm in hospital on medical supplies supplying chain].

PubMed

Sheng, Xi

2012-07-01

The thesis aims to study the automation replenishment algorithm in hospital on medical supplies supplying chain. The mathematical model and algorithm of medical supplies automation replenishment are designed through referring to practical data form hospital on the basis of applying inventory theory, greedy algorithm and partition algorithm. The automation replenishment algorithm is proved to realize automatic calculation of the medical supplies distribution amount and optimize medical supplies distribution scheme. A conclusion could be arrived that the model and algorithm of inventory theory, if applied in medical supplies circulation field, could provide theoretical and technological support for realizing medical supplies automation replenishment of hospital on medical supplies supplying chain.

Exploiting the Phenomenon of Liquid-Liquid Phase Separation for Enhanced and Sustained Membrane Transport of a Poorly Water-Soluble Drug.

PubMed

Indulkar, Anura S; Gao, Yi; Raina, Shweta A; Zhang, Geoff G Z; Taylor, Lynne S

2016-06-06

Recent studies on aqueous supersaturated lipophilic drug solutions prepared by methods including antisolvent addition, pH swing, or dissolution of amorphous solid dispersions (ASDs) have demonstrated that when crystallization is slow, these systems undergo liquid-liquid phase separation (LLPS) when the concentration of the drug in the medium exceeds its amorphous solubility. Following LLPS, a metastable equilibrium is formed where the concentration of drug in the continuous phase corresponds to the amorphous solubility while the dispersed phase is composed of a nanosized drug-rich phase. It has been reasoned that the drug-rich phase may act as a reservoir, enabling the rate of passive transport of the drug across a membrane to be maintained at the maximum value for an extended period of time. Herein, using clotrimazole as a model drug, and a flow-through diffusion cell, the reservoir effect is demonstrated. Supersaturated clotrimazole solutions at concentrations below the amorphous solubility show a linear relationship between the maximum flux and the initial concentration. Once the concentration exceeds the amorphous solubility, the maximum flux achieved reaches a plateau. However, the duration for which the high flux persists was found to be highly dependent on the number of drug-rich nanodroplets present in the donor compartment. Macroscopic amorphous particles of clotrimazole did not lead to the same reservoir effect observed with the nanodroplets formed through the process of LLPS. A first-principles mathematical model was developed which was able to fit the experimental receiver concentration-time profiles for concentration regimes both below and above amorphous solubility, providing support for the contention that the nanodroplet phase does not directly diffuse across the membrane but, instead, rapidly replenishes the drug in the aqueous phase that has been removed by transport across the membrane. This study provides important insight into the properties of supersaturated solutions and how these might in turn impact oral absorption through effects on passive membrane transport rates.

A Technique for Evaluating Vendor Bids for Stock Replenishment of a Consumable Item.

DTIC Science & Technology

1985-06-01

RD-A159 957 A TECHNIQUE FOR EVALUATING VENDOR BIDS FOR STOCK 1/1 REPLENISHMENT OF A CONSUMABLE I TEM(U) NAVAL POSTGRADUATE SCHOOL MONTEREY CA J...REPORT II PER106 COVERED *A Technique for Evaluating Vendor Bids Juner’ 1985 i for Stock Replenishment of a Consumable tern 6. PERFORMING ORG. REPORT...Control Center (SPCC) Uniform Inventory Control Program (UICP) wholesale replenishment model for 1H cognizance symbol ( consumable ) material is an order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brauner, Edwin Jr.; Carlson, Daniel C.

The Geysers steamfields in northern Sonoma County have produced reliable ''green'' power for many years. An impediment to long-term continued production has been the ability to provide a reliable source of injection water to replace water extracted and lost in the form of steam. The steamfield operators have historcially used cooling towers to recycle a small portion of the steam and have collected water during the winter months using stream extraction. These two sources, however, could not by themselves sustain the steamfield in the long term. The Lake County Reclaimed Water Project (SEGEP) was inititated in 1997 and provides anothermore » source of steamfield replenishment water. The Santa Rosa Geysers Recharge Project provides another significant step in replenishing the steamfield. In addition, the Santa Rosa Geysers Recharge Project has been built with capacity to potentially meet virtually all injection water requirements, when combined with these other sources. Figure 2.1 graphically depicts the combination of injection sources.« less

Achieving Stable Radiation Pressure Acceleration of Heavy Ions via Successive Electron Replenishment from Ionization of a High-Z Material Coating

NASA Astrophysics Data System (ADS)

Shen, X. F.; Qiao, B.; Zhang, H.; Kar, S.; Zhou, C. T.; Chang, H. X.; Borghesi, M.; He, X. T.

2017-05-01

A method to achieve stable radiation pressure acceleration (RPA) of heavy ions from laser-irradiated ultrathin foils is proposed, where a high-Z material coating in front is used. The coated high-Z material, acting as a moving electron repository, continuously replenishes the accelerating heavy ion foil with comoving electrons in the light-sail acceleration stage due to its successive ionization under laser fields with Gaussian temporal profile. As a result, the detrimental effects such as foil deformation and electron loss induced by the Rayleigh-Taylor-like and other instabilities in RPA are significantly offset and suppressed so that stable acceleration of heavy ions are maintained. Particle-in-cell simulations show that a monoenergetic Al13 + beam with peak energy 3.8 GeV and particle number 1 010 (charge >20 nC ) can be obtained at intensity 1 022 W /cm2 .

Sunrayce 97 Continues Day 4 - Fulton to Lee's Summit

Science.gov Websites

(202) 586-0713 Lee's Summit, MO -- Massachusetts Institute of Technology (MIT) took Day IV and maintained the overall lead as sunrayce 97 completed its fourth day. The elapsed time for the day for the attaining good sun early enough in the day to replenish the batteries, as such a fast pace will deplete them

Harvesting and replenishment policies for renewable natural resources

USGS Publications Warehouse

Douglas, Aaron J.; Johnson, Richard L.

1993-01-01

The current paper links the optimal intertemporal use of renewable natural resources to the harvesting activities of various economic agents. Previous contributions cite market forces as a causative factor inducing the extirpation of renewable natural resources. The analysis given here discusses investment in the stock of renewable resources and cites important examples of this activity. By introducing joint harvesting and replenishment strategies into a model of renewable resource use, the analysis adds descriptive reality and relevance to positive and normative discussions of renewable natural resource use. A high price for the yield or a high discount rate tend to diminish the size of the optimum stationary stock of the resource with a non-replenishment harvesting strategy. Optimal non-replenishment harvesting strategies for renewable natural resources will exhaustion or extirpation of the resource if the price of the yield or the discount rate are sufficiently large. However, the availability of a replenishment technology and the use of replenishment activities tends to buffer the resource against exhaustion or extirpation.

Magma Reservoirs from the Perspective of Supervolcanoes and Granitic Plutons: "Big Red Blobs" and "Balloons and Soda Straws" are Real

NASA Astrophysics Data System (ADS)

Christiansen, E. H.

2016-12-01

Simple models describing silicic magma reservoirs and their connections with volcanic rocks have been denigrated as "big red blobs" and "balloons-and-soda straws." Although these models are certainly generalized to convey complex relations, there are multiple reasons to accept the existence of large magma chambers and direct connections between volcanoes and plutonic rocks. These include:-Geophysical evidence (seismic, magnetotelluric, and geodetic) for the existence of large bodies of magma in the crust today. Magma is a mixture of liquids, solids, and fluids. It does not have to be melt rich, nor does it need to be mobile and eruptible; it just has to have melt present. -Eruptions of large volumes (>1,000 km3) of dacitic to rhyolitic magma and large collapse calderas (30-50 km across). -The thermal lifetimes of large bodies are extended by high recharge rates. Individual bodies of magma may exist for tens to hundreds of thousands of years.-Geochronological evidence that pluton lifetimes are similar to those of volcanic fields.-Evidence for incremental emplacement of a pluton is not evidence against the former existence of a large magma reservoir, but the natural consequence of ongoing replenishment and crystallization after eruptions cease. Thus, what might have been a large liquid-dominated system at the time of eruption of a large ignimbrite, is subsequently intruded by new batches of magma as it crystallizes and closes down. This destroys the evidence for a large red blob and creates a composite pluton. -Direct and indirect evidence connect plutons to large eruptions. This is shown by field relations, geochronology, as well as chemical, mineralogical, and isotopic similarities of volcanic and plutonic rocks. -Volcanic and plutonic differentiation patterns are very similar, but differ in some ways because cumulates are preserved in the plutonic record and because intrusions continue to differentiate (liquids separate from solids) until the last bit of liquid is consumed. Highly evolved liquids are present in the volcanic record, but are less common than in intrusions. Most plutonic rocks appear to be mixtures of cumulate minerals and interstitial melt unable to separate from the coarsening mush.

A Three-Pool Model Dissecting Readily Releasable Pool Replenishment at the Calyx of Held

PubMed Central

Guo, Jun; Ge, Jian-long; Hao, Mei; Sun, Zhi-cheng; Wu, Xin-sheng; Zhu, Jian-bing; Wang, Wei; Yao, Pan-tong; Lin, Wei; Xue, Lei

2015-01-01

Although vesicle replenishment is critical in maintaining exo-endocytosis recycling, the underlying mechanisms are not well understood. Previous studies have shown that both rapid and slow endocytosis recycle into a very large recycling pool instead of within the readily releasable pool (RRP), and the time course of RRP replenishment is slowed down by more intense stimulation. This finding contradicts the calcium/calmodulin-dependence of RRP replenishment. Here we address this issue and report a three-pool model for RRP replenishment at a central synapse. Both rapid and slow endocytosis provide vesicles to a large reserve pool (RP) ~42.3 times the RRP size. When moving from the RP to the RRP, vesicles entered an intermediate pool (IP) ~2.7 times the RRP size with slow RP-IP kinetics and fast IP-RRP kinetics, which was responsible for the well-established slow and rapid components of RRP replenishment. Depletion of the IP caused the slower RRP replenishment observed after intense stimulation. These results establish, for the first time, a realistic cycling model with all parameters measured, revealing the contribution of each cycling step in synaptic transmission. The results call for modification of the current view of the vesicle recycling steps and their roles. PMID:25825223

Risk Assessment and Scaling for the SLS LH2 ET

NASA Technical Reports Server (NTRS)

Hafiychuk, Halyna; Ponizovskaya-Devine, Ekaterina; Luchinsky, Dmitry; Khasin, Michael; Osipov, Viatcheslav V.; Smelyanskiy, Vadim N.

2012-01-01

In this report the main physics processes in LH2 tank during prepress and rocket flight are studied. The goal of this investigation is to analyze possible hazards and to make risk assessment in proposed LH2 tank designs for SLS with 5 engines (the situation with 4 engines is less critical). For analysis we use the multinode model (MNM) developed by us and presented in a separate report and also 3D ANSYS simulations. We carry out simulation and theoretical analysis the physics processes such as (i) accumulation of bubbles in LH2 during replenish stage and their collapsing in the liquid during the prepress; (ii) condensation-evaporation at the liquid-vapor interface and tank wall, (iv) heating the liquid near the interface and wall due to condensation and environment heat, (v) injection of hot He during prepress and of hot GH2 during flight, (vi) mixing and cooling of the injected gases due to heat transfer between the gases, liquid and the tank wall. We analyze the effects of these physical processes on the thermo- and fluid gas dynamics in the ullage and on the stratification of temperature in the liquid and assess the associated hazards. A special emphasize is put on the scaling predictions for the larger SLS LH2 tank.

Design and Development of the Liquid Lithium Limiter (L3) for CDX-U

NASA Astrophysics Data System (ADS)

Seraydarian, R. P.; Chousal, L.; Doerner, R. P.; Luckhardt, S. C.; Lynch, T.

2000-10-01

--- This poster describes experiments with liquid Li that informed the design of a Liquid Lithium Limter (L3) built by UCSD for installation on the CDX-U spherical torus at PPPL. It was necessary to resort to wetting liquid Li to textured structures in order for the limiter to intercept 2-3 density e-folding lengths of the scrape off layer (3 cm) of the CDX-U plasma. Since Li is chemically active and corrodes rapidly in all but the driest air, we carried out wetting experiments in vacuum (10-7 - 10-8 torr) and also in Ar at near atmospheric pressure. Wetting of steel occurred reliably at substrate temperatures near 500 ^oC under all conditions, but this high temperature presented special problems of rapid material loss through evaporation, especially under vacuum. Once the surface is wetted, however, lost Li can be replenished at ~ 200 ^oC (just above the melting temperature) where evaporation is negligible. A wetted limiter can even be cooled to room temperature and then reheated many hours later as long as clean conditions are maintained. Surface textures, heating techniques, effective seal materials for piston-driven liquid Li reservoirs, and other aspects of the limiter system design will be presented. Work supported by US DOE grant DE-FG03-95ER54301

Actin-filament disassembly: it takes two to shrink them fast.

PubMed

Winterhoff, Moritz; Faix, Jan

2015-06-01

Actin-filament disassembly is indispensable for replenishing the pool of polymerizable actin and allows continuous dynamic remodelling of the actin cytoskeleton. A new study now reveals that ADF/cofilin preferentially dismantles branched networks and provides new insights into the collaborative work of ADF/cofilin and Aip1 on filament disassembly at the molecular level. Copyright © 2015 Elsevier Ltd. All rights reserved.

Silicon dendritic web growth

NASA Technical Reports Server (NTRS)

Duncan, S.

1984-01-01

Technological goals for a silicon dendritic web growth program effort are presented. Principle objectives for this program include: (1) grow long web crystals front continuously replenished melt; (2) develop temperature distribution in web and melt; (3) improve reproductibility of growth; (4) develop configurations for increased growth rates (width and speed); (5) develop new growth system components as required for improved growth; and (6) evaluate quality of web growth.

Replenishment policy for an inventory model under inflation

NASA Astrophysics Data System (ADS)

Singh, Vikramjeet; Saxena, Seema; Singh, Pushpinder; Mishra, Nitin Kumar

2017-07-01

The purpose of replenishment is to keep the flow of inventory in the system. To determine an optimal replenishment policy is a great challenge in developing an inventory model. Inflation is defined as the rate at which the prices of goods and services are rising over a time period. The cost parameters are affected by the rate of inflation. High rate of inflation affects the organizations financial conditions. Based on the above backdrop the present paper proposes the retailers replenishment policy for deteriorating items with different cycle lengths under inflation. The shortages are partially backlogged. At last numerical examples validate the results.

Ceramic micro-injection molded nozzles for serial femtosecond crystallography sample delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beyerlein, K. R.; Heymann, M.; Kirian, R.

Serial femtosecond crystallography (SFX) using X-ray Free-Electron Lasers (XFELs) allows for room temperature protein structure determination without evidence of conventional radiation damage. In this method, a liquid suspension of protein microcrystals can be delivered to the X-ray beam in vacuum as a micro-jet, which replenishes the crystals at a rate that exceeds the current XFEL pulse repetition rate. Gas dynamic virtual nozzles produce the required micrometer-sized streams by the focusing action of a coaxial sheath gas and have been shown to be effective for SFX experiments. Here, we describe the design and characterization of such nozzles assembled from ceramic micro-injectionmore » molded outer gas-focusing capillaries. Trends of the emitted jet diameter and jet length as a function of supplied liquid and gas flow rates are measured by a fast imaging system. The observed trends are explained by derived relationships considering choked gas flow and liquid flow conservation. Finally, the performance of these nozzles in a SFX experiment is presented, including an analysis of the observed background.« less

Automatic Control of Silicon Melt Level

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Stickel, W. B.

1982-01-01

A new circuit, when combined with melt-replenishment system and melt level sensor, offers continuous closed-loop automatic control of melt-level during web growth. Installed on silicon-web furnace, circuit controls melt-level to within 0.1 mm for as long as 8 hours. Circuit affords greater area growth rate and higher web quality, automatic melt-level control also allows semiautomatic growth of web over long periods which can greatly reduce costs.

Connectivity and systemic resilience of the Great Barrier Reef

PubMed Central

Wolff, Nicholas H.; Ortiz, Juan C.; Condie, Scott A.; Anthony, Kenneth R. N.; Blackwell, Paul G.; Mumby, Peter J.

2017-01-01

Australia’s iconic Great Barrier Reef (GBR) continues to suffer from repeated impacts of cyclones, coral bleaching, and outbreaks of the coral-eating crown-of-thorns starfish (COTS), losing much of its coral cover in the process. This raises the question of the ecosystem’s systemic resilience and its ability to rebound after large-scale population loss. Here, we reveal that around 100 reefs of the GBR, or around 3%, have the ideal properties to facilitate recovery of disturbed areas, thereby imparting a level of systemic resilience and aiding its continued recovery. These reefs (1) are highly connected by ocean currents to the wider reef network, (2) have a relatively low risk of exposure to disturbances so that they are likely to provide replenishment when other reefs are depleted, and (3) have an ability to promote recovery of desirable species but are unlikely to either experience or spread COTS outbreaks. The great replenishment potential of these ‘robust source reefs’, which may supply 47% of the ecosystem in a single dispersal event, emerges from the interaction between oceanographic conditions and geographic location, a process that is likely to be repeated in other reef systems. Such natural resilience of reef systems will become increasingly important as the frequency of disturbances accelerates under climate change. PMID:29182630

Connectivity and systemic resilience of the Great Barrier Reef.

PubMed

Hock, Karlo; Wolff, Nicholas H; Ortiz, Juan C; Condie, Scott A; Anthony, Kenneth R N; Blackwell, Paul G; Mumby, Peter J

2017-11-01

Australia's iconic Great Barrier Reef (GBR) continues to suffer from repeated impacts of cyclones, coral bleaching, and outbreaks of the coral-eating crown-of-thorns starfish (COTS), losing much of its coral cover in the process. This raises the question of the ecosystem's systemic resilience and its ability to rebound after large-scale population loss. Here, we reveal that around 100 reefs of the GBR, or around 3%, have the ideal properties to facilitate recovery of disturbed areas, thereby imparting a level of systemic resilience and aiding its continued recovery. These reefs (1) are highly connected by ocean currents to the wider reef network, (2) have a relatively low risk of exposure to disturbances so that they are likely to provide replenishment when other reefs are depleted, and (3) have an ability to promote recovery of desirable species but are unlikely to either experience or spread COTS outbreaks. The great replenishment potential of these 'robust source reefs', which may supply 47% of the ecosystem in a single dispersal event, emerges from the interaction between oceanographic conditions and geographic location, a process that is likely to be repeated in other reef systems. Such natural resilience of reef systems will become increasingly important as the frequency of disturbances accelerates under climate change.

Achieving Stable Radiation Pressure Acceleration of Heavy Ions via Successive Electron Replenishment from Ionization of a High-Z Material Coating.

PubMed

Shen, X F; Qiao, B; Zhang, H; Kar, S; Zhou, C T; Chang, H X; Borghesi, M; He, X T

2017-05-19

A method to achieve stable radiation pressure acceleration (RPA) of heavy ions from laser-irradiated ultrathin foils is proposed, where a high-Z material coating in front is used. The coated high-Z material, acting as a moving electron repository, continuously replenishes the accelerating heavy ion foil with comoving electrons in the light-sail acceleration stage due to its successive ionization under laser fields with Gaussian temporal profile. As a result, the detrimental effects such as foil deformation and electron loss induced by the Rayleigh-Taylor-like and other instabilities in RPA are significantly offset and suppressed so that stable acceleration of heavy ions are maintained. Particle-in-cell simulations show that a monoenergetic Al^{13+} beam with peak energy 3.8 GeV and particle number 10^{10} (charge >20  nC) can be obtained at intensity 10^{22}  W/cm^{2}.

Abundance and composition of juvenile corals reveals divergent trajectories for coral assemblages across the United Arab Emirates.

PubMed

Pratchett, Morgan S; Baird, Andrew H; Bauman, Andrew G; Burt, John A

2017-01-30

Marked shifts in the composition of coral assemblages are occurring at many locations, but it is unknown whether these are permanent shifts reinforced by patterns of population replenishment. This study examined the composition of juvenile coral assemblages across the United Arab Emirates (UAE). Densities of juvenile corals varied significantly among locations, but were highest where coral cover was highest. Juvenile coral assemblages within the Persian Gulf were dominated by Porites, while no Acropora were recorded. We expect therefore, continued declines in Acropora abundance, while observed dominance of Porites is likely to persist. In the Oman Sea, Pocillopora was the dominant juvenile coral, with Acropora and Stylophora also recorded. This study shows that taxonomic differences in replenishment are reinforcing temporal shifts in coral composition within the southern Persian Gulf, but not in the Oman Sea. Differences in environmental conditions and disturbance regimes likely explain the divergent responses between regions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Siderophile and chalcophile metals as tracers of the evolution of the Siberian Trap in the Noril'sk region, Russia

NASA Astrophysics Data System (ADS)

Brügmann, G. E.; Naldrett, A. J.; Asif, M.; Lightfoot, P. C.; Gorbachev, N. S.; Fedorenko, V. A.

1993-05-01

In this study Cu, Ni, and platinum-group elements (PGE) were determined in a sequence of basaltic and picritic lavas from the Siberian Trap in the Noril'sk area of Russia to constrain genetic relationships between the basalts and the petrogenesis of Ni-Cu-PGE sulfide deposits associated with the Talnakh and Noril'sk intrusions. In the most primitive basalts (8-19 wt% MgO) of the Tuklonsky (Tk) suite, Pt and Pd concentrations range from 4-13 ppb, increasing with decreasing MgO content; whereas Ir contents decrease with MgO from 0.8-0.05 ppb. The contrasting behavior of these elements, which all have very high sulfide-silicate partition coefficients, as well as the primitive mantle-like ratios of Cu/Y and Pd/Y, suggests that these magmas were not sulfide-saturated. The high PGE abundances imply that their parental magmas were also not sulfide saturated during partial melting in the mantle. Due to sulfide segregation, the overlying basalts of the Nadezhdinsky (Nd) series are low in Cu and Ni (52 and 38 ppm, respectively); highly depleted in all PGE; and have very low Cu/Y, Pd/Y, and Pd/Cu ratios. However, in stratigraphically higher levels, Cu, Ni, and PGE concentrations increase systematically through the Morongovsky (Mr) suite to reach a concentration plateau in the uppermost Mokulaevsky (Mk) suite (Pt 8 ppb; Pd: 9 ppb; Ir: 0.12 ppb; Rh: 0.4 ppb). At the same time, ratios such as Cu/Y increase and approach primitive mantle values. However, ratios involving PGE, such as Pd/Y, remain low, suggesting the removal of small amounts of sulfide (0.01-0.03%). The compositional variations in the basalts and the sulfide liquids can be quantitatively described by fractional segregation of a sulfide liquid in an open- or closed-system magma chamber. The latter model suggests that the basalts represent the eruption products of a zoned magma chamber in which light magma, with crustal components contaminated, overlies less contaminated, denser magma. Crustal contamination caused sulfide saturation, and the resulting sulfide liquids settled through a magma column and accumulated at the bottom of the chamber. In this model, the sulfide liquid is not in equilibrium with the whole magma mass, and sulfide segregation is compared with the zone-refining process of metallurgy. The sulfides become more enriched as they move through the magma; and although the magma left behind is depleted in PGE, Cu, and Ni, their concentrations also increase with depth. Eventually, the magma chamber is emptied from the top to the bottom, producing the flood basalt sequence and the associated intrusions and ore deposits. In the open-system model, sulfide saturation was initially caused by assimilation of crustal material by the Tuklonsky magma. Continuous and simultaneous replenishment, assimilation, and crystallization processes formed the lower Nd lavas. The concurrent removal of 0.5-1% sulfide strongly depleted these magmas in chalcophile and siderophile metals. Due to the continuous replenishment of the magma chamber with uncontaminated PGE-rich magma, succeeding lavas (Mr, Mk) show diminishing signs of crustal contamination and become less sulfide-saturated, as indicated by the increasing Ni, Cu, and PGE abundances. During the evolution of the chamber, the magma remained sulfur-saturated, and sulfides accumulated at the base. The composition of the sulfide ores could be regarded as a mixture consisting of low Ni-, Cu-, and PGE-sulfides derived with a low silicate/sulfide ratio (100) from the Tk-Nd magma and high Ni-, Cu-, and PGE-sulfides formed with a high ratio (10,000) from the Mr-Mk magma.

Segregation control in vertical Bridgman crystal growth

NASA Astrophysics Data System (ADS)

Tao, Y.; Kou, S.

1996-11-01

To help the crystal grow at a constant dopant concentration in vertical Bridgman crystal growth, the dopant concentration of the growth melt, i.e. the melt from which the crystal grows, was kept constant. To achieve this, three different methods were used to replenish the growth melt at a controlled rate and suppress dopant diffusion between the growth melt and the replenishing melt. In method one, a replenishing crucible having a long melt passageway was immersed in the growth melt. In method two, a replenishing crucible having an independent feed-rate control mechanism was held above the growth melt. In method three, a submerged diffusion baffle was used to form a long melt passageway between the growth melt and the replenishing melt. NaNO 3 was used as a model material for crystal growth. Single crystals were grown by these three methods with effective segregation control. Method two was applied to InSb and single crystals were also grown with effective segregation control.

A supplier selection and order allocation problem with stochastic demands

NASA Astrophysics Data System (ADS)

Zhou, Yun; Zhao, Lei; Zhao, Xiaobo; Jiang, Jianhua

2011-08-01

We consider a system comprising a retailer and a set of candidate suppliers that operates within a finite planning horizon of multiple periods. The retailer replenishes its inventory from the suppliers and satisfies stochastic customer demands. At the beginning of each period, the retailer makes decisions on the replenishment quantity, supplier selection and order allocation among the selected suppliers. An optimisation problem is formulated to minimise the total expected system cost, which includes an outer level stochastic dynamic program for the optimal replenishment quantity and an inner level integer program for supplier selection and order allocation with a given replenishment quantity. For the inner level subproblem, we develop a polynomial algorithm to obtain optimal decisions. For the outer level subproblem, we propose an efficient heuristic for the system with integer-valued inventory, based on the structural properties of the system with real-valued inventory. We investigate the efficiency of the proposed solution approach, as well as the impact of parameters on the optimal replenishment decision with numerical experiments.

Establishment of vesicular-arbuscular mycorrhizal fungi and other microorganisms on a beach replenishment site in Florida.

PubMed

Sylvia, D M; Will, M E

1988-02-01

Beach replenishment is a widely used method of controlling coastal erosion. To reduce erosional losses from wind, beach grasses are often planted on the replenishment sands. However, there is little information on the microbial populations in this material that may affect plant establishment and growth. The objectives of this research were to document changes in the populations of vesicular-arbuscular mycorrhizal (VAM) fungi and other soil microorganisms in replenishment materials and to determine whether roots of transplanted beach grasses become colonized by beneficial microbes. The study was conducted over a 2-year period on a replenishment project in northeastern Florida. Three sampling locations were established at 1-km intervals along the beach. Each location consisted of three plots: an established dune, replenishment sand planted with Uniola paniculata and Panicum sp., and replenishment sand left unplanted. Fungal and bacterial populations increased rapidly in the rhizosphere of beach grasses in the planted plots. However, no bacteria were recovered that could fix significant amounts of N(2). The VAM fungi established slowly on the transplanted grasses. Even after two growing seasons, levels of root colonization and sporulation were significantly below those found in the established dune. There was a shift in the dominant VAM fungi found in the planted zone with respect to those in the established dunes. The most abundant species recovered from the established dunes were Glomus deserticola, followed by Acaulospora scrobiculata and Scutellospora weresubiae. The VAM fungi that colonized the planted zone most rapidly were Glomus globiferum, followed by G. deserticola and Glomus aggregatum.

An Analysis of Causes of Contract Price Change for Competitive Procurements of Replenishment Spare Parts.

DTIC Science & Technology

1984-09-01

Research Study Number Three. In 1982, Mr. Edward Brost , then a graduate student at AFIT, completed a thesis which further analyzed the effects of sole...task, Brost formulated three research questions. They are as follows: 1. Is there a reduction in replenishment spare parts prices when competition is...analysis, Brost made three significant conclusions. They are: 1. The introduction of competition into the replenishment spare parts acquisition process

High-bandwidth continuous-flow arc furnace

DOEpatents

Hardt, David E.; Lee, Steven G.

1996-01-01

A high-bandwidth continuous-flow arc furnace for stream welding applications includes a metal mass contained in a crucible having an orifice. A power source charges an electrode for generating an arc between the electrode and the mass. The arc heats the metal mass to a molten state. A pressurized gas source propels the molten metal mass through the crucible orifice in a continuous stream. As the metal is ejected, a metal feeder replenishes the molten metal bath. A control system regulates the electrode current, shielding gas pressure, and metal source to provide a continuous flow of molten metal at the crucible orifice. Independent control over the electrode current and shield gas pressure decouples the metal flow temperature and the molten metal flow rate, improving control over resultant weld characteristics.

High-bandwidth continuous-flow arc furnace

DOEpatents

Hardt, D.E.; Lee, S.G.

1996-08-06

A high-bandwidth continuous-flow arc furnace for stream welding applications includes a metal mass contained in a crucible having an orifice. A power source charges an electrode for generating an arc between the electrode and the mass. The arc heats the metal mass to a molten state. A pressurized gas source propels the molten metal mass through the crucible orifice in a continuous stream. As the metal is ejected, a metal feeder replenishes the molten metal bath. A control system regulates the electrode current, shielding gas pressure, and metal source to provide a continuous flow of molten metal at the crucible orifice. Independent control over the electrode current and shield gas pressure decouples the metal flow temperature and the molten metal flow rate, improving control over resultant weld characteristics. 4 figs.

On-Orbit and Ground Performance of the PGBA Plant Growth Facility

NASA Technical Reports Server (NTRS)

Hoehn, A.; Chamberlain, D. J.; Forsyth, S. W.; Hanna, D. S.; Scovazzo, P.; Stodieck, L. S.; Heyenga, G.; Kliss, Mark

1997-01-01

PGBA, a plant growth facility developed for commercial space biotechnology research, successfully grew a total of 30 plants (6 species) for 10 days on board the Space Shuttle Endeavour (STS-77) and is scheduled for reflight on board MSL-1 (STS-83) for a 16 day flight. The PGBA life support systems provide atmospheric, thermal, and humidity control as well as lighting and nutrient supply in a 23.6 liter chamber. Atmosphere treatment includes ethylene and other hydrocarbon removal, CO2 replenishment, and O2 control. The normally closed system uses controlled CO2 replenishment from the crew cabin as required by the plants. Temperature is controlled (1 C) at user-specified setpoints between 20-32 C, using water-filled coolant loops, solid state Peltier thermoelectric devices, and liquid heat exchangers. The thermoelectric cooling systems were optimized for low power consumption and high cooling efficiencies. Relative humidity is maintained between 60-100% using a cooled porous metal plate to remove water vapor from the air stream without cooling the bulk air below the dew point. The lighting system utilizes three compact fluorescent bi-axial lights with variable lighting control and light intensity (PAR) between 220 and 330 micromol/sq m/s at a distance of 20 cm in spaceflight configuration (on orbit power limited to 230 Watt for entire payload). A ground, up to 550 micromol/sq m/s light intensity can be achieved with 330 Watt payload power consumption. Plant water and nutrient support is sustained via the 'Nutrient Pack' system including the passive or active 'Water Replenishable Nutrient Pack.' The root matrix material (soil or Agar) and nutrient formulation of each pack is prepared according to plant species and experimental requirements. These systems were designed by NASA Ames personnel. Data acquisition and control systems provide 32 channels of environmental data as well as digitized or analog video signals for downlink.

Improvements in the processing of large grain, bulk Y-Ba-Cu-O superconductors via the use of additional liquid phase

NASA Astrophysics Data System (ADS)

Congreve, Jasmin V. J.; Shi, Yunhua; Dennis, Anthony R.; Durrell, John H.; Cardwell, David A.

2017-01-01

A major limitation to the widespread application of Y-Ba-Cu-O (YBCO) bulk superconductors is the relative complexity and low yield of the top seeded melt growth (TSMG) process, by which these materials are commonly fabricated. It has been demonstrated in previous work on the recycling of samples in which the primary growth had failed, that the provision of an additional liquid-rich phase to replenish liquid lost during the failed growth process leads to the reliable growth of relatively high quality recycled samples. In this paper we describe the adaptation of the liquid phase enrichment technique to the primary TSMG fabrication process. We further describe the observed differences between the microstructure and superconducting properties of samples grown with additional liquid-rich phase and control samples grown using a conventional TSMG process. We observe that the introduction of the additional liquid-rich phase leads to the formation of a higher concentration of Y species at the growth front, which leads, in turn, to a more uniform composition at the growth front. Importantly, the increased uniformity at the growth front leads directly to an increased homogeneity in the distribution of the Y-211 inclusions in the superconducting Y-123 phase matrix and to a more uniform Y-123 phase itself. Overall, the provision of an additional liquid-rich phase improves significantly both the reliability of grain growth through the sample thickness and the magnitude and homogeneity of the superconducting properties of these samples compared to those fabricated by a conventional TSMG process.

What makes a planet habitable, and how to search for habitable planets in other solar systems.

PubMed

Papagiannis, M D

1992-06-01

The availability of liquid water is the most important factor that makes a planet habitable, because water is a very effective polar molecule and hence an excellent solvent and facilitator for the complex chemistry of life. Its presence presupposes a planet with a significant mass that guarantees the presence of a substantial atmosphere, and a reasonable spinning rate to avoid overheating. It also implies that the planet is at moderate distances from its central star, a range that is called the Ecosphere or the Habitable Zone. Since the evolution of life to high intelligence seems to take billions of years, it requires also that the central star must be neither too massive, that will produce a lot of lethal UV radiation and will have too short a life-span to allow life to evolve, nor of very small mass which will be producing too feeble a radiation to sustain life. The detection of free Oxygen in the atmosphere of a planet is a very strong evidence for the presence of life, because Oxygen is highly reactive and would rapidly disappear by combining with other elements, unless it is continuously replenished by life as the by-product of the process of photosynthesis that builds food for life (sugars) from CO2 and H2O.

Mammography film processor replenishment rate: bromide level monitoring.

PubMed

Kimme-Smith, C; Wuelfing, P; Kitts, E L; Cagnon, C; Basic, M; Bassett, L

1997-03-01

The effects of the mammography film processing replenishment rate on contrast and speed are studied sensitometrically. Two experiments studied decreasing replenishment rates in the Kodak RP developer and quantified changes in the developer by measuring bromide ion concentrations. First, values of NaBr concentration from 1.7 to 8.4 g/L, achieved by reducing the replenishment rate, were tested with sensitometry strips. Second, the developer replenishment rate of a high volume dedicated mammography processor was reduced by one-third, to 20 cm3/1560 cm2, so that the NaBr concentration rose from 2.0 to 12.36. Sensitometric results for four film types and patient films were tested for changes from standard values as NaBr concentration was restored to 3.31 g/L. Fifty-five clinical images obtained at 7.3-9.3 NaBr g/L were compared to their matching previous films, with NaBr levels of 2-3 g/L, for contrast and visibility of the skin line. For the range of the NaBr ion from 1.7 to 7 g/L, no significant sensitometric differences were found. Above 7 g/L, different film types had different sensitometric results. From 7.3 to 9.3 NaBr g/L, 47.5% of the clinical films reviewed by four radiologists had less contrast compared to previous films. Dedicated mammography processors with high film volume (i.e., those that do not have excessive oxidation or foreign dye problems) can operate at lower replenishment rates than are currently employed. All common mammography film types are stable at these lower replenishment rates up to 7.0 NaBr g/L.

Genetic Connectivity among and Self-Replenishment within Island Populations of a Restricted Range Subtropical Reef Fish

PubMed Central

van der Meer, Martin H.; Hobbs, Jean-Paul A.; Jones, Geoffrey P.; van Herwerden, Lynne

2012-01-01

Marine protected areas (MPAs) are increasingly being advocated and implemented to protect biodiversity on coral reefs. Networks of appropriately sized and spaced reserves can capture a high proportion of species diversity, with gene flow among reserves presumed to promote long term resilience of populations to spatially variable threats. However, numerically rare small range species distributed among isolated locations appear to be at particular risk of extinction and the likely benefits of MPA networks are uncertain. Here we use mitochondrial and microsatellite data to infer evolutionary and contemporary gene flow among isolated locations as well as levels of self-replenishment within locations of the endemic anemonefish Amphiprion mccullochi, restricted to three MPA offshore reefs in subtropical East Australia. We infer high levels of gene flow and genetic diversity among locations over evolutionary time, but limited contemporary gene flow amongst locations and high levels of self-replenishment (68 to 84%) within locations over contemporary time. While long distance dispersal explained the species’ integrity in the past, high levels of self-replenishment suggest locations are predominantly maintained by local replenishment. Should local extinction occur, contemporary rescue effects through large scale connectivity are unlikely. For isolated islands with large numbers of endemic species, and high local replenishment, there is a high premium on local species-specific management actions. PMID:23185398

Thermal control of low-pressure fractionation processes. [in basaltic magma solidification

NASA Technical Reports Server (NTRS)

Usselman, T. M.; Hodge, D. S.

1978-01-01

Thermal models detailing the solidification paths for shallow basaltic magma chambers (both open and closed systems) were calculated using finite-difference techniques. The total solidification time for closed chambers are comparable to previously published calculations; however, the temperature-time paths are not. These paths are dependent on the phase relations and the crystallinity of the system, because both affect the manner in which the latent heat of crystallization is distributed. In open systems, where a chamber would be periodically replenished with additional parental liquid, calculations indicate that the possibility is strong that a steady-state temperature interval is achieved near a major phase boundary. In these cases it is straightforward to analyze fractionation models of the basaltic liquid evolution and their corresponding cumulate sequences. This steady thermal fractionating state can be invoked to explain large amounts of erupted basalts of similar composition over long time periods from the same volcanic center and some rhythmically layered basic cumulate sequences.

Design of a liquid membrane target for high repetition rate neutron generation

NASA Astrophysics Data System (ADS)

Poole, Patrick; Andereck, C. David; Storm, Mike; Schumacher, Douglass

2013-10-01

Ultra-bright, pulsed, spatially-small sources of energetic neutrons have applications in radiography and non-destructive remote sensing. Neutrons can be generated by a process wherein ions accelerated from a laser-irradiated primary target subsequently bombard a converter material, causing neutron-producing nuclear reactions, such as 7Li(d,n)8Be. Deuterons from this process are suppressed by contamination that builds up on the rear of the solid primary target. To eliminate this issue we propose a self-replenishing liquid membrane target consisting of heavy water and deuterated surfactant, formed in-vacuum within a moveable wire frame. In addition to removing issues associated with solid target positioning and collateral damage, this apparatus provides flow rate and target thickness control, and allows for the high repetition rates required to generate desired neutron fluxes with a portable laser-based system. The apparatus design will be presented, as well as a novel interferometric method that measures the membrane thickness using tightly-focused light. This work was performed with support from DARPA.

Develop and test fuel cell powered on-site integrated total energy systems

NASA Technical Reports Server (NTRS)

Kaufman, A.; Pudick, S.; Wang, C. L.; Werth, J.; Whelan, J. A.

1984-01-01

On-going testing of an 11 cell, 10.7 in. x 14 in. stack (about 1 kW) reached 2600 hours on steady load. Nonmetallic cooling plates and an automated electrolyte replenishment system continued to perform well. A 10 cell, 10.7 in. x 14 in. stack was constructed with a modified electrolyte matrix configuration for the purpose of reducing cell IR loss. The desired effect was achieved, but the general cell performance level was irregular. Evaluation is continuing. Preparations for a long term 25 cell, 13 in. x 23 in. test stack (about 4 kW) approached completion. Start up in early May 1984 is expected.

Replenishable food supply on Mars

NASA Technical Reports Server (NTRS)

1990-01-01

The design team's present objective is to design a facility which will provide an environment to grow plants on the surface of Mars for a continuous supply of food for a ten-man crew. The main focus of the project is the design of a greenhouse. Concentration of the current design effort is on the outer structure, internal layout, and construction methods. The project was conducted by undergraduate students at Prairie View A&M University during Fall 1989 and Spring 1990.

Corrosive resistant heat exchanger

DOEpatents

Richlen, Scott L.

1989-01-01

A corrosive and errosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is conveyed through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium.

41 CFR 101-27.102-2 - Guidelines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Replenishment § 101-27.102-2 Guidelines. Guidelines for implementing the EOQ principle of stock replenishment are in the GSA Handbook, The Economic Order Quantity Principle and Applications, issued by the Federal...

Optimal dynamic pricing and replenishment policy for perishable items with inventory-level-dependent demand

NASA Astrophysics Data System (ADS)

Lu, Lihao; Zhang, Jianxiong; Tang, Wansheng

2016-04-01

An inventory system for perishable items with limited replenishment capacity is introduced in this paper. The demand rate depends on the stock quantity displayed in the store as well as the sales price. With the goal to realise profit maximisation, an optimisation problem is addressed to seek for the optimal joint dynamic pricing and replenishment policy which is obtained by solving the optimisation problem with Pontryagin's maximum principle. A joint mixed policy, in which the sales price is a static decision variable and the replenishment rate remains to be a dynamic decision variable, is presented to compare with the joint dynamic policy. Numerical results demonstrate the advantages of the joint dynamic one, and further show the effects of different system parameters on the optimal joint dynamic policy and the maximal total profit.

Prevalence and Predictive Value of Microvascular Flow Abnormalities after Successful Contemporary Percutaneous Coronary Intervention in Acute ST-Segment Elevation Myocardial Infarction.

PubMed

Aggarwal, Sourabh; Xie, Feng; High, Robin; Pavlides, Gregory; Porter, Thomas R

2018-06-01

Although microvascular flow abnormalities have been observed following epicardial recanalization in acute ST-segment elevation myocardial infarction (STEMI), the prevalence and severity of these abnormalities in the current era of rapid percutaneous coronary intervention (PCI) has not been evaluated. The objective of this study was to assess microvascular perfusion (MVP) following successful primary PCI in patients with STEMI and how it affects clinical outcome. In this single-center, retrospective study, 170 patients who successfully underwent emergent PCI for STEMI were assessed using real-time myocardial contrast echocardiography using a continuous infusion of intravenous commercial microbubbles (3% Definity). Three patterns of myocardial contrast replenishment were observed following intermittent high-mechanical index impulses: infarct zone replenishment within 4 sec (normal MVP), delays in contrast replenishment but normal plateau intensity (delayed MVP [dMVP]), and both delays in replenishment and reduced plateau intensity (microvascular obstruction [MVO]). Changes in left ventricular ejection fraction at 6 months and clinical event rate at 12 months (death, recurrent infarction, need for defibrillator placement, or heart failure admission) were compared. Normal MVP was seen in 62 patients (36%), dMVP in 49 (29%), and MVO in 59 (35%). Left anterior descending coronary artery infarct location was the only parameter independently associated with dMVP or MVO, independent of age, cardiac risk factors, door-to-dilation time, pre-PCI Thrombolysis In Myocardial Infarction flow grade, and thrombus burden. A dMVP pattern had a similar reduction in left ventricular ejection fraction as MVO at hospital discharge but had recovery of left ventricular ejection fraction at 6 months and a greater than fourfold lower event rate than the MVO group (P < .001). MVO and dMVP are frequently seen following contemporary successful PCI for STEMI, especially following left anterior descending coronary artery infarction. Despite a similar area at risk, a dMVP pattern has better functional recovery and clinical outcome than MVO. Copyright © 2018 American Society of Echocardiography. Published by Elsevier Inc. All rights reserved.

Continuous production of lactic acid from molasses by perfusion culture of Lactococcus lactis using a stirred ceramic membrane reactor.

PubMed

Ohashi, R; Yamamoto, T; Suzuki, T

1999-01-01

A perfusion culture system was used for continuous production of lactic acid by retaining cells at a high density of Lactococcus lactis in a stirred ceramic membrane reactor (SCMR). After the cell concentration increased to 248 g/l, half of the culture broth volume was replaced with the fermentation medium. Subsequently, a substrate solution containing glucose (run 1) or molasses (run 2) was continuously supplied to the cells retained in the SCMR. Simultaneously, the culture supernatant was extracted using a ceramic filter with a pore size of 0.2 mum. The dilution rate was initially set at 0.4 h(-1) and gradually decreased to 0.2 h(-1) due to reduction in the permeability of the filter. The concentration of glucose in the substrate solution was adjusted to 60 g/l for the transition and the first period until 240 h, 90 g/l for the second period from 240 h to 440 h, and 70 g/l for the third period from 440 h to 643 h. The average concentration of lactic acid in the filtrate reached 46 g/l in the first period, 43 g/l in the second period, and 33 g/l for the third period. The productivity obtained for the first period reached 15.8 g.l(-1).h(-1), twice as much as that achieved in repeated batch fermentations. Based on the results obtained in run 1, the substrate solution containing 120 g/l of molasses was continuously supplied for 240 h in run 2. The concentration and productivity of lactic acid reached 40 g/l and 10.6 g.l(-1).h(-1), respectively, by continuously replenishing the culture medium at a dilution rate of 0.26 h(-1). These results demonstrated that the filtration capacity of the SCMR was sufficient for a continuous and rapid replenishment of molasses solution from the dense cell culture and, therefore, the perfusion culture system is considered to provide a low-cost process for continuous production of lactic acid from cheap resources.

A corrosive resistant heat exchanger

DOEpatents

Richlen, S.L.

1987-08-10

A corrosive and erosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is pumped through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium. 3 figs., 3 tabs.

Release and Establishment of Sameodes albiguttalis for Biological Control of Waterhyacinth.

DTIC Science & Technology

1981-02-01

Multiply By To Obtain acres 4046.856 square metres feet 0.3048 metres inches 25.4 millimetres miles (U. S. statute) 1.609344 kilometres 9 RELEASE AND...turnover rate in the harvesting and restocking operations, i. e., by continually removing and replenishing the plants. Since an acre of waterhyacinth can...30 m by 30 m was fenced in by constructing a compound from chicken wire. Since waterhya- cinth was not growing in this area, plants were transferred

Low-cost solar array project task 1: Silicon material. Gaseous melt replenishment system

NASA Technical Reports Server (NTRS)

Jewett, D. N.; Bates, H. E.; Hill, D. M.

1980-01-01

The operation of a silicon production technique was demonstrated. The essentials of the method comprise chemical vapor deposition of silicon, by hydrogen reduction of chlorosilanes, on the inside of a quartz reaction vessel having large internal surface area. The system was designed to allow successive deposition-melting cycles, with silicon removal being accomplished by discharging the molten silicon. The liquid product would be suitable for transfer to a crystal growth process, casting into solid form, or production of shots. A scaled-down prototype reactor demonstrated single pass conversion efficiency of 20 percent and deposition rates and energy consumption better than conventional Siemens reactors, via deposition rates of 365 microns/hr. and electrical consumption of 35 Kwhr/kg of silicon produced.

A Quantitative Study of Vertical Replenishment and its Contribution to Momentum Recovery for a Large Offshore Windfarm

NASA Astrophysics Data System (ADS)

Gupta, T.; Baidya Roy, S.; Miller, L.

2017-12-01

With rapid increase in the installed wind capacity around the globe, it is important and interesting to understand the processes involved in wind farm-atmospheric boundary layer interactions. A wind turbine extracts energy from the mean flow and converts it into electrical energy, thereby reducing the mean kinetic energy available. The corresponding reduction in momentum triggers vertical mixing that transports high-momentum air from aloft to the wind turbine layer thereby replenishing the lost momentum, at least partially. This study investigates the phenomenon of vertical replenishment and quantifies its contribution in the momentum recovery as a function of various factors including installed capacity (MW/km2), depth of the wind farm (km) and climatology of the area. Numerical experiments are conducted using the WRF mesoscale model to simulate wind turbine-boundary layer interactions in a hypothetical large off-shore wind farm located deep in the Arabian Sea off the western coast of India. WRF is equipped with a wind turbine parameterization and is capable of simulating both the momentum reduction and vertical replenishment phenomena. It is found that the downward turbulent flux is able to replenish about 66% of momentum lost because of wind turbines. Additionally, the feedback leads to an average increase of 1.5% in generated power capacity in the wind farm. These results indicate that when the momentum deficit occurs, the vertical replenishment in form of turbulent flux tries to dampen the momentum loss, hence, acting as a negative feedback in the wind farm.

Case report: hydroquinone and/or glutaraldehyde induced acute myeloid leukaemia?

PubMed Central

Makropoulos , Vassilios; Alexopoulos, Evangelos C

2006-01-01

Background Exposures to high doses of irradiation, to chemotherapy, benzene, petroleum products, paints, embalming fluids, ethylene oxide, herbicides, pesticides, and smoking have been associated with an increased risk of acute myelogenous leukemia (AML). Although there in no epidemiological evidence of relation between X-ray developer, fixer and replenisher liquids and AML, these included glutaraldehyde which has weakly associated with lymphocytic leukemia in rats and hydroquinone has been increasingly implicated in producing leukemia, causing DNA and chromosomal damage, inhibits topo-isomerase II, alter hematopoiesis and inhibit apoptosis of neoplastic cells. Case presentation Two white females (A and B) hired in 1985 as medical radiation technologists in a primary care center, in Greece. In July 2001, woman A, 38-years-old, was diagnosed as having acute monocytic leukaemia (FAB M5). The patient did not respond to therapy and died threeweeks later. In August 2001, woman B, 35-year-old, was diagnosed with acute promyelocytic leukaemia (FAB M3). Since discharge, she is in continuous complete remission. Both women were non smokers without any medical history. Shortly after these incidents official inspectors and experts inspected workplace, examined equipment, archives of repairs, notes, interviewed and monitored employees. They concluded that shielding was inadequate for balcony's door but personal monitoring did not show any exceeding of TLV of 20 mSv yearly and cytogenetics analysis did not reveal findings considered to be characteristics of ionizing exposure. Equipment for developing photos had a long list of repairs, mainly leakages of liquids and increases of temperature. On several occasions the floor has been flooded especially during 1987–1993 and 1997–2001. Inspection confirmed a complete lack of ventilation and many spoiled medical x-ray films. Employees reported that an "osmic" level was continuously evident and frequently developed symptoms of respiratory irritation and dizziness. Conclusion The findings support the hypothesis that the specific AML cases might have originated from exposure to chemicals, especially hydroquinone and/or glutaraldehyde. The report also emphasises the crucial role of inspection of facilities and enforcement of compliance with regulations in order to prevent similar incidents. PMID:16872480

Flood replenishment: a new method of processor control.

PubMed

Frank, E D; Gray, J E; Wilken, D A

1980-01-01

In mechanized radiographic film processors that process medium to low volumes of film, roll films, and those that process single-emulsion films from nuclear medicine scans, computed tomography, and ultrasound, it is difficult to maintain the developer solution at a stable processing level. We describe our experience using flood replenishment, which is a method in which developer replenisher containing starter solution is introduced in the processor at timed intervals, independent of the number of films being processed. By this process, a stable level of developer activity is maintained in a processor used to develop a medium to low volume of single-emulsion film.

[Investigation on chromatogram-pharmacodynamics relationship of Angelica sinensis on effect of replenishing blood].

PubMed

Yang, Ying-Lai; Cui, Fang; Hu, Fang; Guo, Long; Yang, Tao; Li, Ying-Dong; Feng, Shi-Lan

2013-11-01

Blood deficiency model of mice was copied by subcutaneous injection with 200, 100 and 100 mg x kg(-1) (0.01 mL x g(-1)) acetyl phenylhydrazine (APH) at the frist, fourth, and seventh days. Mice in each group were perfused with different extracted parts of Angelica sinensis (drug dosage was 2.4 g x kg(-1)) at the tenth day, once a day for 10 days. Then compare the influence of different extracted parts of Angelica sinensis to RBC, Hb, PLT and thymus, spleen and weight changes of blood deficiency mice. The peak areas of each common peak from HPLC fingerprint were associated with the date of replenishing blood pharmacodynamics efficacy by using gray relation statistic, which was used to research the chromatogram-pharmacodynamics relationship. The results showed that the part of DSC has the better effect in replenishing blood. The contribution degree of the DSC to replenishing blood of each component were determined by correlation size, and ferulic acid made the largest contribution, but contribution of other components should not be ignored. In this paper, we research the relationship of the HPLC fingerprint and spectrum activity relationship, determine the material basis of the DSC for replenishing blood, and provide effective way to represent the spectral correlation effect.

Depositional features and stratigraphic sections in granitic plutons: implications for the emplacement and crystallization of granitic magma

NASA Astrophysics Data System (ADS)

Wiebe, R. A.; Collins, W. J.

1998-09-01

Many granitic plutons contain sheet-like masses of dioritic to gabbroic rocks or swarms of mafic to intermediate enclaves which represent the input of higher temperature, more mafic magma during crystallization of the granitic plutons. Small-scale structures associated with these bodies (e.g. load-cast and compaction features, silicic pipes extending from granitic layers into adjacent gabbroic sheets) indicate that the sheets and enclave swarms were deposited on a floor of the magma chamber (on granitic crystal mush and beneath crystal-poor magma) while the mafic magma was incompletely crystallized. These structures indicate 'way up', typically toward the interior of the intrusions, and appear to indicate that packages of mafic sheets and enclave concentrations in these plutons are a record of sequential deposition. Hence, these plutons preserve a stratigraphic history of events involved in the construction (filling, replenishment) and crystallization of the magma chamber. The distinctive features of these depositional portions of plutons allow them to be distinguished from sheeted intrusions, which usually preserve mutual intrusive contacts and 'dike-sill' relations of different magma types. The considerable thickness of material that can be interpreted as depositional, and the evidence for replenishment, suggest that magma chamber volumes at any one time were probably much less than the final size of the pluton. Thus, magma chambers may be constructed much more slowly than presently envisaged. The present steep attitudes of these structures in many plutons may have developed gradually as the floor of the chamber (along with the underlying solidified granite and country rock) sank during continuing episodes of magma chamber replenishment. These internal magmatic structures support recent suggestions that the room problem for granites could be largely accommodated by downward movement of country rock beneath the magma chamber.

Periodic behavior in lava dome eruptions

NASA Astrophysics Data System (ADS)

Barmin, A.; Melnik, O.; Sparks, R. S. J.

2002-05-01

Lava dome eruptions commonly display fairly regular alternations between periods of high activity and periods of low or no activity. The time scale for these alternations is typically months to several years. Here we develop a generic model of magma discharge through a conduit from an open-system magma chamber with continuous replenishment. The model takes account of the principal controls on flow, namely the replenishment rate, magma chamber size, elastic deformation of the chamber walls, conduit resistance, and variations of magma viscosity, which are controlled by degassing during ascent and kinetics of crystallization. The analysis indicates a rich diversity of behavior with periodic patterns similar to those observed. Magma chamber size can be estimated from the period with longer periods implying larger chambers. Many features observed in volcanic eruptions such as alternations between periodic behaviors and continuous discharge, sharp changes in discharge rate, and transitions from effusive to catastrophic explosive eruption can be understood in terms of the non-linear dynamics of conduit flows from open-system magma chambers. The dynamics of lava dome growth at Mount St. Helens (1980-1987) and Santiaguito (1922-2000) was analyzed with the help of the model. The best-fit models give magma chamber volumes of ∼0.6 km3 for Mount St. Helens and ∼65 km3 for Santiaguito. The larger magma chamber volume is the major factor in explaining why Santiaguito is a long-lived eruption with a longer periodicity of pulsations in comparison with Mount St. Helens.

Temperature-Modulated Array High-Performance Liquid Chromatography

PubMed Central

Premstaller, Andreas; Xiao, Wenzhong; Oberacher, Herbert; O'Keefe, Matthew; Stern, David; Willis, Thomas; Huber, Christian G.; Oefner, Peter J.

2001-01-01

Using novel monolithic poly(styrene-divinylbenzene) capillary columns with an internal diameter of 0.2 mm, we demonstrate for the first time the feasibility of constructing high-performance liquid chromatography arrays for the detection of mutations by heteroduplex analysis under partially denaturing conditions. In one embodiment, such an array can be used to analyze one sample simultaneously at different temperatures to maximize the detection of mutations in DNA fragments containing multiple discrete melting domains. Alternatively, one may inject different samples onto columns kept at the same effective temperature. Further improvements in throughput can be obtained by means of laser-induced fluorescence detection and the differential labeling of samples with up to four different fluorophores. Major advantages of monolithic capillary high-performance liquid chromatographic arrays over their capillary electrophoretic analogs are the chemical inertness of the poly(styrene-divinylbenzene) stationary phase, the physical robustness of the column bed due to its covalent linkage to the inner surface of the fused silica capillary, and the feasibility to modify the stationary phase thereby allowing the separation of compounds not only on the principle of size exclusion, but also adsorption, distribution, and ion exchange. Analyses times are on the order of a few minutes and turnaround time is extremely short as there is no need for the replenishment of the separation matrix between runs. PMID:11691859

Attrition analysed in five waves of a longitudinal yearly survey of smokers: findings from the ITC Netherlands survey.

PubMed

Zethof, Dennis; Nagelhout, Gera E; de Rooij, Mark; Driezen, Pete; Fong, Geoffrey T; van den Putte, Bas; Hummel, Karin; de Vries, Hein; Thompson, Mary E; Willemsen, Marc C

2016-08-01

Attrition bias can affect the external validity of findings. This article analyses attrition bias and assesses the effectiveness of replenishment samples on demographic and smoking-related characteristics for the International Tobacco Control Netherlands Survey, a longitudinal survey among smokers. Attrition analyses were conducted for the first five survey waves (2008-12). We assessed, including and excluding replenishment samples, whether the demographic composition of the samples changed between the first and fifth waves. Replenishment samples were tailored to ensure the sample remained representative of the smoking population. We also constructed a multivariable survival model of attrition that included all five waves with replenishment samples. Of the original 1820 respondents recruited in 2008, 46% participated again in 2012. Demographic differences between waves due to attrition were generally small and replenishment samples tended to minimize them further. The multivariable survival analysis revealed that only two of the 10 variables analysed were significant predictors of attrition: a weak effect for gender (men dropped out more often) and weak to moderate effects for age (respondents aged 15-24 years dropped out more than aged 25-39 years, who dropped out more than those aged 40+ years). Weak to moderate attrition effects were found for men and younger age groups. This information could be used to minimize respondent attrition. Our findings suggest that sampling weights and tailored replenishment samples can effectively compensate for attrition effects. This is already being done for the International Tobacco Control Netherlands Survey, including the categories that significantly predicted attrition in this study. © The Author 2016. Published by Oxford University Press on behalf of the European Public Health Association. All rights reserved.

Nectar replenishment maintains the neutral effects of nectar robbing on female reproductive success of Salvia przewalskii (Lamiaceae), a plant pollinated and robbed by bumble bees

PubMed Central

Ye, Zhong-Ming; Jin, Xiao-Fang; Inouye, David W.

2017-01-01

Background and Aims It has been suggested that the dynamics of nectar replenishment could differ for flowers after being nectar robbed or visited legitimately, but further experimental work is needed to investigate this hypothesis. This study aimed to assess the role of nectar replenishment in mediating the effects of nectar robbing on pollinator behaviour and plant reproduction. Methods Plant–robber–pollinator interactions in an alpine plant, Salvia przewalskii, were studied. It is pollinated by long-tongued Bombus religiosus and short-tongued B. friseanus, but robbed by B. friseanus. Nectar production rates for flowers after they were either robbed or legitimately visited were compared, and three levels of nectar robbing were created to detect the effects of nectar robbing on pollinator behaviour and plant reproduction. Key Results Nectar replenishment did not differ between flowers that had been robbed or legitimately visited. Neither fruit set nor seed set was significantly affected by nectar robbing. In addition, nectar robbing did not significantly affect visitation rate, flowers visited within a plant per foraging bout, or flower handling time of the legitimate pollinators. However, a tendency for a decrease in relative abundance of the pollinator B. religiosus with an increase of nectar robbing was found. Conclusions Nectar robbing did not affect female reproductive success because nectar replenishment ensures that pollinators maintain their visiting activity to nectar-robbed flowers. Nectar replenishment might be a defence mechanism against nectar robbing to enhance reproductive fitness by maintaining attractiveness to pollinators. Further studies are needed to reveal the potential for interference competition among bumble bees foraging as robbers and legitimate visitors, and to investigate variation of nectar robbing in communities with different bumble bee species composition. PMID:28158409

Calmodulin enhances ribbon replenishment and shapes filtering of synaptic transmission by cone photoreceptors

PubMed Central

Parmelee, Caitlyn M.; Chen, Minghui; Cork, Karlene M.; Curto, Carina; Thoreson, Wallace B.

2014-01-01

At the first synapse in the vertebrate visual pathway, light-evoked changes in photoreceptor membrane potential alter the rate of glutamate release onto second-order retinal neurons. This process depends on the synaptic ribbon, a specialized structure found at various sensory synapses, to provide a supply of primed vesicles for release. Calcium (Ca2+) accelerates the replenishment of vesicles at cone ribbon synapses, but the mechanisms underlying this acceleration and its functional implications for vision are unknown. We studied vesicle replenishment using paired whole-cell recordings of cones and postsynaptic neurons in tiger salamander retinas and found that it involves two kinetic mechanisms, the faster of which was diminished by calmodulin (CaM) inhibitors. We developed an analytical model that can be applied to both conventional and ribbon synapses and showed that vesicle resupply is limited by a simple time constant, τ = 1/(Dρδs), where D is the vesicle diffusion coefficient, δ is the vesicle diameter, ρ is the vesicle density, and s is the probability of vesicle attachment. The combination of electrophysiological measurements, modeling, and total internal reflection fluorescence microscopy of single synaptic vesicles suggested that CaM speeds replenishment by enhancing vesicle attachment to the ribbon. Using electroretinogram and whole-cell recordings of light responses, we found that enhanced replenishment improves the ability of cone synapses to signal darkness after brief flashes of light and enhances the amplitude of responses to higher-frequency stimuli. By accelerating the resupply of vesicles to the ribbon, CaM extends the temporal range of synaptic transmission, allowing cones to transmit higher-frequency visual information to downstream neurons. Thus, the ability of the visual system to encode time-varying stimuli is shaped by the dynamics of vesicle replenishment at photoreceptor synaptic ribbons. PMID:25311636

Prevention of upper aerodigestive tract cancer in zinc-deficient rodents: Inefficacy of genetic or pharmacological disruption of COX-2

PubMed Central

Fong, Louise Y.Y.; Jiang, Yubao; Riley, Maurisa; Liu, Xianglan; Smalley, Karl J.; Guttridge, Denis C.; Farber, John L.

2009-01-01

Zinc deficiency in humans is associated with an increased risk of upper aerodigestive tract (UADT) cancer. In rodents, zinc deficiency predisposes to carcinogenesis by causing proliferation and alterations in gene expression. We examined whether in zinc-deficient rodents, targeted disruption of the cyclooxygenase (COX)-2 pathway by the COX-2 selective inhibitor celecoxib or by genetic deletion prevent UADT carcinogenesis. Tongue cancer prevention studies were conducted in zinc-deficient rats previously exposed to a tongue carcinogen by celecoxib treatment with or without zinc replenishment, or by zinc replenishment alone. The ability of genetic COX-2 deletion to protect against chemically-induced for-estomach tumorigenesis was examined in mice on zinc-deficient versus zinc-sufficient diet. The expression of 3 predictive bio-markers COX-2, nuclear factor (NF)-κ B p65 and leukotriene A4 hydrolase (LTA4H) was examined by immunohistochemistry. In zinc-deficient rats, celecoxib without zinc replenishment reduced lingual tumor multiplicity but not progression to malignancy. Celecoxib with zinc replenishment or zinc replenishment alone significantly lowered lingual squamous cell carcinoma incidence, as well as tumor multiplicity. Celecoxib alone reduced overexpression of the 3 biomarkers in tumors slightly, compared with intervention with zinc replenishment. Instead of being protected, zinc-deficient COX-2 null mice developed significantly greater tumor multiplicity and forestomach carcinoma incidence than wild-type controls. Additionally, zinc-deficient COX-2−/− forestomachs displayed strong LTA4H immunostaining, indicating activation of an alter-native pathway under zinc deficiency when the COX-2 pathway is blocked. Thus, targeting only the COX-2 pathway in zinc-deficient animals did not prevent UADT carcinogenesis. Our data suggest zinc supplementation should be more thoroughly explored in human prevention clinical trials for UADT cancer. PMID:17985342

Ceramic micro-injection molded nozzles for serial femtosecond crystallography sample delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beyerlein, K. R.; Adriano, L.; Heymann, M.

Serial femtosecond crystallography (SFX) using X-ray Free-Electron Lasers (XFELs) allows for room temperature protein structure determination without evidence of conventional radiation damage. In this method, a liquid suspension of protein microcrystals can be delivered to the X-ray beam in vacuum as a micro-jet, which replenishes the crystals at a rate that exceeds the current XFEL pulse repetition rate. Gas dynamic virtual nozzles produce the required micrometer-sized streams by the focusing action of a coaxial sheath gas and have been shown to be effective for SFX experiments. Here, we describe the design and characterization of such nozzles assembled from ceramic micro-injectionmore » molded outer gas-focusing capillaries. Trends of the emitted jet diameter and jet length as a function of supplied liquid and gas flow rates are measured by a fast imaging system. The observed trends are explained by derived relationships considering choked gas flow and liquidflow conservation. In conclusion, the performance of these nozzles in a SFX experiment is presented, including an analysis of the observed background.« less

Ceramic micro-injection molded nozzles for serial femtosecond crystallography sample delivery

DOE PAGES

Beyerlein, K. R.; Adriano, L.; Heymann, M.; ...

2015-12-08

Serial femtosecond crystallography (SFX) using X-ray Free-Electron Lasers (XFELs) allows for room temperature protein structure determination without evidence of conventional radiation damage. In this method, a liquid suspension of protein microcrystals can be delivered to the X-ray beam in vacuum as a micro-jet, which replenishes the crystals at a rate that exceeds the current XFEL pulse repetition rate. Gas dynamic virtual nozzles produce the required micrometer-sized streams by the focusing action of a coaxial sheath gas and have been shown to be effective for SFX experiments. Here, we describe the design and characterization of such nozzles assembled from ceramic micro-injectionmore » molded outer gas-focusing capillaries. Trends of the emitted jet diameter and jet length as a function of supplied liquid and gas flow rates are measured by a fast imaging system. The observed trends are explained by derived relationships considering choked gas flow and liquidflow conservation. In conclusion, the performance of these nozzles in a SFX experiment is presented, including an analysis of the observed background.« less

Low cost solar array project. Task 1: Silicon material, gaseous melt replenishment system

NASA Technical Reports Server (NTRS)

Jewett, D. N.; Bates, H. E.; Hill, D. M.

1979-01-01

A system to combine silicon formation, by hydrogen reduction of trichlorosilane, with the capability to replenish a crystal growth system is described. A variety of process parameters to allow sizing and specification of gas handling system components was estimated.

Optimal pricing and replenishment policies for instantaneous deteriorating items with backlogging and trade credit under inflation

NASA Astrophysics Data System (ADS)

Sundara Rajan, R.; Uthayakumar, R.

2017-12-01

In this paper we develop an economic order quantity model to investigate the optimal replenishment policies for instantaneous deteriorating items under inflation and trade credit. Demand rate is a linear function of selling price and decreases negative exponentially with time over a finite planning horizon. Shortages are allowed and partially backlogged. Under these conditions, we model the retailer's inventory system as a profit maximization problem to determine the optimal selling price, optimal order quantity and optimal replenishment time. An easy-to-use algorithm is developed to determine the optimal replenishment policies for the retailer. We also provide optimal present value of profit when shortages are completely backlogged as a special case. Numerical examples are presented to illustrate the algorithm provided to obtain optimal profit. And we also obtain managerial implications from numerical examples to substantiate our model. The results show that there is an improvement in total profit from complete backlogging rather than the items being partially backlogged.

XMM-Newton mission operations - ready for its third decade

NASA Astrophysics Data System (ADS)

Kirsch, M.; Finn, T.; Godard, T.; v. Krusenstiern, N.; Pfeil, N.; Salt, D.; Toma, L.; Webert, D.; Weissmann, U.

2017-10-01

The XMM-Newton X-ray space observatory is approaching its third decade of operations. The spacecraft and payload are operating without major degradation and scientific demand is continuously very high. With the change to a new way of using the Attitude and Orbit control System in 2013 the fuel consumption was reduced by a factor of two, additionally this has reduced stress on the reaction wheels. The challenge for the next decade is now to ensure that the saved fuel is available for continuous usage. We will describe the process of the so called 'fuel migration and replenishment' activities needed to keep the spacecraft operational potentially up to 2029+. We provide as well an overall health status of the mission, the evolution of the ground segment and concepts on streamlining mission operations with continued high safety requirements using automation tools.

Multi-timescale analysis of a metabolic network in synthetic biology: a kinetic model for 3-hydroxypropionic acid production via beta-alanine.

PubMed

Dalwadi, Mohit P; King, John R; Minton, Nigel P

2018-07-01

A biosustainable production route for 3-hydroxypropionic acid (3HP), an important platform chemical, would allow 3HP to be produced without using fossil fuels. We are interested in investigating a potential biochemical route to 3HP from pyruvate through [Formula: see text]-alanine and, in this paper, we develop and solve a mathematical model for the reaction kinetics of the metabolites involved in this pathway. We consider two limiting cases, one where the levels of pyruvate are never replenished, the other where the levels of pyruvate are continuously replenished and thus kept constant. We exploit the natural separation of both the time scales and the metabolite concentrations to make significant asymptotic progress in understanding the system without resorting to computationally expensive parameter sweeps. Using our asymptotic results, we are able to predict the most important reactions to maximize the production of 3HP in this system while reducing the maximum amount of the toxic intermediate compound malonic semi-aldehyde present at any one time, and thus we are able to recommend which enzymes experimentalists should focus on manipulating.

Glucose Starvation Inhibits Autophagy via Vacuolar Hydrolysis and Induces Plasma Membrane Internalization by Down-regulating Recycling*

PubMed Central

Lang, Michael J.; Martinez-Marquez, Jorge Y.; Prosser, Derek C.; Ganser, Laura R.; Buelto, Destiney; Wendland, Beverly; Duncan, Mara C.

2014-01-01

Cellular energy influences all aspects of cellular function. Although cells can adapt to a gradual reduction in energy, acute energy depletion poses a unique challenge. Because acute depletion hampers the transport of new energy sources into the cell, the cell must use endogenous substrates to replenish energy after acute depletion. In the yeast Saccharomyces cerevisiae, glucose starvation causes an acute depletion of intracellular energy that recovers during continued glucose starvation. However, how the cell replenishes energy during the early phase of glucose starvation is unknown. In this study, we investigated the role of pathways that deliver proteins and lipids to the vacuole during glucose starvation. We report that in response to glucose starvation, plasma membrane proteins are directed to the vacuole through reduced recycling at the endosomes. Furthermore, we found that vacuolar hydrolysis inhibits macroautophagy in a target of rapamycin complex 1-dependent manner. Accordingly, we found that endocytosis and hydrolysis are required for survival in glucose starvation, whereas macroautophagy is dispensable. Together, these results suggest that hydrolysis of components delivered to the vacuole independent of autophagy is the cell survival mechanism used by S. cerevisiae in response to glucose starvation. PMID:24753258

Achieving Stable Radiation Pressure Acceleration of Heavy Ions via Successive Electron Replenishment from Ionization of a High-Z Material Coating

NASA Astrophysics Data System (ADS)

Qiao, Bin; Shen, X. F.; Zhang, H.; Kar, S.; Zhou, C. T.; Chang, H. X.; Borghesi, M.; He, X. T.

2017-10-01

Among various laser-driven acceleration schemes, radiation pressure acceleration (RPA) is regarded as one of the most promising schemes to obtain high-quality ion beams. Although RPA is very attractive in principle, it is difficult to be achieved experimentally. One of the most important reasons is the dramatic growth of the multi-dimensional Rayleigh-Taylor-like (RT) instabilities. In this talk, we report a novel method to achieve stable RPA of ions from laser-irradiated ultrathin foils, where a high-Z material coating in front is used. The coated high-Z material, acting as a moving electron repository, continuously replenishes the accelerating ion foil with comoving electrons in the light-sail acceleration stage due to its successive ionization under laser fields with Gaussian temporal profile. As a result, the detrimental effects such as electron loss induced by the RT and other instabilities are significantly offset and suppressed so that stable acceleration of ions are maintained. Supported by the NSAF, Grant No. U1630246; the NNSF China Grants No. 11575298; and the National Key Program of S&T Research and Development, Grant No. 2016YFA0401100.

Analysis of the single-vehicle cyclic inventory routing problem

NASA Astrophysics Data System (ADS)

Aghezzaf, El-Houssaine; Zhong, Yiqing; Raa, Birger; Mateo, Manel

2012-11-01

The single-vehicle cyclic inventory routing problem (SV-CIRP) consists of a repetitive distribution of a product from a single depot to a selected subset of customers. For each customer, selected for replenishments, the supplier collects a corresponding fixed reward. The objective is to determine the subset of customers to replenish, the quantity of the product to be delivered to each and to design the vehicle route so that the resulting profit (difference between the total reward and the total logistical cost) is maximised while preventing stockouts at each of the selected customers. This problem appears often as a sub-problem in many logistical problems. In this article, the SV-CIRP is formulated as a mixed-integer program with a nonlinear objective function. After a thorough analysis of the structure of the problem and its features, an exact algorithm for its solution is proposed. This exact algorithm requires only solutions of linear mixed-integer programs. Values of a savings-based heuristic for this problem are compared to the optimal values obtained for a set of some test problems. In general, the gap may get as large as 25%, which justifies the effort to continue exploring and developing exact and approximation algorithms for the SV-CIRP.

Achieving Stable Radiation Pressure Acceleration of Heavy Ions via Successive Electron Replenishment from Ionization of a High-Z Material Coating

NASA Astrophysics Data System (ADS)

Shen, X. F.; Qiao, B.; Chang, H. X.; Kar, S.; Zhou, C. T.; Borghesi, M.; He, X. T.

2016-10-01

Generation of monoenergetic heavy ion beams aroused more scientific interest in recent years. Radiation pressure acceleration (RPA) is an ideal mechanism for obtaining high-quality heavy ion beams, in principle. However, to achieve the same energy per nucleon (velocity) as protons, heavy ions undergo much more serious Rayleigh-Taylor-like (RT) instability and afterwards much worse Coulomb explosion due to loss of co-moving electrons. This leads to premature acceleration termination of heavy ions and very low energy attained in experiment. The utilization of a high-Z coating in front of the target may suppress the RT instability and Coulomb explosion by continuously replenishing the accelerating heavy ion foil with co-moving electrons due to its successive ionization under laser fields with Gaussian temporal and spatial profiles. Thus stable RPA can be realized. Two-dimensional and three-dimensional particles-in-cell simulations with dynamic ionization show that a monoenergetic Al13+ beam with peak energy 4.0GeV and particle number 1010 (charge > 20nC) can be obtained at intensity 1022 W/cm2. Supported by the NSF, Nos. 11575298 and 1000-Talents Program of China.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howell, C; Vu, TL; Lin, JJ

Inspired by the long-term effectiveness of living antifouling materials, we have developed a method for the self-replenishment of synthetic biofouling-release surfaces. These surfaces are created by either molding or directly embedding 3D vascular systems into polydimethylsiloxane (PDMS) and filling them with a silicone oil to generate a nontoxic oil-infused material. When replenished with silicone oil from an outside source, these materials are capable of self-lubrication and continuous renewal of the interfacial fouling-release layer. Under accelerated lubricant loss conditions, fully infused vascularized samples retained significantly more lubricant than equivalent nonvascularized controls. Tests of lubricant-infused PDMS in static cultures of the infectiousmore » bacteria Staphylococcus aureus and Escherichia coli as well as the green microalgae Botryococcus braunii, Chlamydomonas reinhardtii, Dunaliella sauna, and Nannochloropsis oculata showed a significant reduction in biofilm adhesion compared to PDMS and glass controls containing no lubricant. Further experiments on vascularized versus nonvascularized samples that had been subjected to accelerated lubricant evaporation conditions for up to 48 h showed significantly less biofilm adherence on the vascularized surfaces. These results demonstrate the ability of an embedded lubricant-filled vascular network to improve the longevity of fouling-release surfaces.« less

Self-Replenishing Vascularized Fouling-Release Surfaces

DOE PAGES

Howell, Caitlin; Vu, Thy L.; Lin, Jennifer J.; ...

2014-08-13

Inspired by the long-term effectiveness of living antifouling materials, we have developed a method for the selfreplenishment of synthetic biofouling-release surfaces. These surfaces are created by either molding or directly embedding 3D vascular systems into polydimethylsiloxane (PDMS) and filling them with a silicone oil to generate a nontoxic oil-infused material. When replenished with silicone oil from an outside source, these materials are capable of self-lubrication and continuous renewal of the interfacial fouling-release layer. Under accelerated lubricant loss conditions, fully infused vascularized samples retained significantly more lubricant than equivalent nonvascularized controls. Tests of lubricant-infused PDMS in static cultures of the infectiousmore » bacteria Staphylococcus aureus and Escherichia coli as well as the green microalgae Botryococcus braunii, Chlamydomonas reinhardtii, Dunaliella salina, and Nannochloropsis oculata showed a significant reduction in biofilm adhesion compared to PDMS and glass controls containing no lubricant. Further experiments on vascularized versus nonvascularized samples that had been subjected to accelerated lubricant evaporation conditions for up to 48 h showed significantly less biofilm adherence on the vascularized surfaces. These results demonstrate the ability of an embedded lubricant-filled vascular network to improve the longevity of fouling-release surfaces.« less

Bioluminescence of Marine Dinoflagellates

PubMed Central

Seliger, H. H.; Fastie, W. G.; Taylor, W. R.; McElroy, W. D.

1962-01-01

Portable light-baffled underwater photometers have been designed for the measurement of dinoflagellate bioluminescence by day and night. Maximal light emission is obtained by mechanical stimulation in a defined volume. The pump which stimulates the dinoflagellates also constantly replenishes the sample volume so that continuous measurements are possible. Evidence for both diurnal variation and vertical migration is presented. Using luminous bacteria for calibration a single dinoflagellate has been found to emit of the order of 1010 light quanta per flash. The technique suggests that large scale mapping of bioluminescence is feasible. PMID:19873546

THE BREAKDOWN OF THE PROTECTIVE OXIDE FILM ON TRANSITION METAL ALLOYS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smeltzer, W.W.

1960-04-01

Initial breaks in oxidation curves of iron-chromium alloys were found to be associated with the ferriteaustenitic phase transformation. This transformation was caused by preferential oxidation of chromium at a rate much larger than its replenishment by diffusion the metal-oxide interface. The stress resulting from this transformation caused breakdown of the protective oxide film. Results indicated that continuous oxidation curves for iron-chromium alloys could be obtained under conditions where preferential oxidation of in alloy constituent did not cause the ferritic-austentic phase transformation. (M.C.G.)

Ultra high frequency follow-on communications satellite system

NASA Astrophysics Data System (ADS)

Hassien, Michael J.

1992-03-01

The existing constellation of UHF communications satellites (LEASAT and FLTSAT) provide key command and control links for mobile forces of the DoD and other government agencies. The UHF Follow-On satellite program will provide for a new generation of communications satellites to replace the existing ones as they reach the end of their life cycle beginning in 1992. Continued coverage is required for both peacetime and crisis environments, and must be maintained indefinitely. An eight-satellite UFO constellation (two per coverage area) will replenish the existing FLTSATCOM constellation.

Dye laser amplifier including a low turbulence, stagnation-free dye flow configuration

DOEpatents

Davin, J.

1992-12-01

A large (high flow rate) dye laser amplifier in which a continuous replenished supply of dye is excited by a first light beam, specifically a copper vapor laser beam, in order to amplify the intensity of a second different light beam, specifically a dye beam, passing through the dye is disclosed herein. This amplifier includes a dye cell defining a dye chamber through which a continuous stream of dye is caused to pass at a flow rate of for example 30 gallons/minute, a specifically designed support vessel for containing the dye cell and a screen device for insuring that the dye stream passes into the dye cell in a substantially turbulent free, stagnation-free manner. 9 figs.

NASA Propulsion Engineering Research Center, volume 2

NASA Technical Reports Server (NTRS)

1993-01-01

On 8-9 Sep. 1993, the Propulsion Engineering Research Center (PERC) at The Pennsylvania State University held its Fifth Annual Symposium. PERC was initiated in 1988 by a grant from the NASA Office of Aeronautics and Space Technology as a part of the University Space Engineering Research Center (USERC) program; the purpose of the USERC program is to replenish and enhance the capabilities of our Nation's engineering community to meet its future space technology needs. The Centers are designed to advance the state-of-the-art in key space-related engineering disciplines and to promote and support engineering education for the next generation of engineers for the national space program and related commercial space endeavors. Research on the following areas was initiated: liquid, solid, and hybrid chemical propulsion, nuclear propulsion, electrical propulsion, and advanced propulsion concepts.

48 CFR 217.7505 - Limitations on price increases.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Limitations on price... Acquisition of Replenishment Parts 217.7505 Limitations on price increases. This section provides implementing... award, on a sole source basis, a contract for any centrally managed replenishment part when the price of...

Process Redesign of the Norwegian Navy Materiel Command’s Replenishment of Inventory Items

DTIC Science & Technology

1997-12-01

procurement offices into one. The second proposal is to introduce, and use electronic commerce in the replenishment process. It is concluded that both...redesign proposals will reduce administrative lead-time, variability and hence cost. Benefits from an introduction of electronic commerce will yield a yearly

The Rapid Rise in the Cost of Replenishment Spare Parts: Are We Making Progress?

DTIC Science & Technology

1985-09-01

Replenishment Spare Parts, Unpublished Master’s Thesis, Air Force Institute of Technology, Wright-Patterson AFB OH, 1984. 2. Brost , Edward J. A...and P. George Benson. Statistics for Business and Economics (Second Edition). San Francisco: Dellen Publishing Company, 1982. 14. Office of Federal

78 FR 51098 - Apricots Grown in Designated Counties in Washington; Increased Assessment Rate

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-20

... in the Committee's proposed budget and replenish its reserve. The proposed assessment rate would... to fund a proposed increase in administrative costs and to replenish the reserve. The increased... fee; $1,200 for Committee travel; $1,000 for the annual audit; and $670 for office supplies, insurance...

7 CFR 97.104 - Application or certificate abandoned.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Failure to replenish viable basic seed within 3 months from the date of request shall result in the... specified in the notice of allowance is not paid within 1 month from the date of the notice, the application... basic seed sample of the variety and shall pay the handling fee for replenishment. Upon request, the...

7 CFR 97.104 - Application or certificate abandoned.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Failure to replenish viable basic seed within 3 months from the date of request shall result in the... specified in the notice of allowance is not paid within 1 month from the date of the notice, the application... basic seed sample of the variety and shall pay the handling fee for replenishment. Upon request, the...

7 CFR 97.104 - Application or certificate abandoned.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Failure to replenish viable basic seed within 3 months from the date of request shall result in the... specified in the notice of allowance is not paid within 1 month from the date of the notice, the application... basic seed sample of the variety and shall pay the handling fee for replenishment. Upon request, the...

7 CFR 97.104 - Application or certificate abandoned.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Failure to replenish viable basic seed within 3 months from the date of request shall result in the... specified in the notice of allowance is not paid within 1 month from the date of the notice, the application... basic seed sample of the variety and shall pay the handling fee for replenishment. Upon request, the...

A continuous record of intereruption velocity change at Mount St. Helens from coda wave interferometry

USGS Publications Warehouse

Hotovec-Ellis, Alicia J.; Gomberg, Joan S.; Vidale, John; Creager, Ken C.

2014-01-01

In September 2004, Mount St. Helens volcano erupted after nearly 18 years of quiescence. However, it is unclear from the limited geophysical observations when or if the magma chamber replenished following the 1980–1986 eruptions in the years before the 2004–2008 extrusive eruption. We use coda wave interferometry with repeating earthquakes to measure small changes in the velocity structure of Mount St. Helens volcano that might indicate magmatic intrusion. By combining observations of relative velocity changes from many closely located earthquake sources, we solve for a continuous function of velocity changes with time. We find that seasonal effects dominate the relative velocity changes. Seismicity rates and repeating earthquake occurrence also vary seasonally; therefore, velocity changes and seismicity are likely modulated by snow loading, fluid saturation, and/or changes in groundwater level. We estimate hydrologic effects impart stress changes on the order of tens of kilopascals within the upper 4 km, resulting in annual velocity variations of 0.5 to 1%. The largest nonseasonal change is a decrease in velocity at the time of the deep Mw = 6.8 Nisqually earthquake. We find no systematic velocity changes during the most likely times of intrusions, consistent with a lack of observable surface deformation. We conclude that if replenishing intrusions occurred, they did not alter seismic velocities where this technique is sensitive due to either their small size or the finite compressibility of the magma chamber. We interpret the observed velocity changes and shallow seasonal seismicity as a response to small stress changes in a shallow, pressurized system.

MITEE-B: A Compact Ultra Lightweight Bi-Modal Nuclear Propulsion Engine for Robotic Planetary Science Missions

NASA Astrophysics Data System (ADS)

Powell, James; Maise, George; Paniagua, John; Borowski, Stanley

2003-01-01

Nuclear thermal propulsion (NTP) enables unique new robotic planetary science missions that are impossible with chemical or nuclear electric propulsion systems. A compact and ultra lightweight bi-modal nuclear engine, termed MITEE-B (MInature ReacTor EnginE - Bi-Modal) can deliver 1000's of kilograms of propulsive thrust when it operates in the NTP mode, and many kilowatts of continuous electric power when it operates in the electric generation mode. The high propulsive thrust NTP mode enables spacecraft to land and takeoff from the surface of a planet or moon, to hop to multiple widely separated sites on the surface, and virtually unlimited flight in planetary atmospheres. The continuous electric generation mode enables a spacecraft to replenish its propellant by processing in-situ resources, provide power for controls, instruments, and communications while in space and on the surface, and operate electric propulsion units. Six examples of unique and important missions enabled by the MITEE-B engine are described, including: (1) Pluto lander and sample return; (2) Europa lander and ocean explorer; (3) Mars Hopper; (4) Jupiter atmospheric flyer; (5) SunBurn hypervelocity spacecraft; and (6) He3 mining from Uranus. Many additional important missions are enabled by MITEE-B. A strong technology base for MITEE-B already exists. With a vigorous development program, it could be ready for initial robotic science and exploration missions by 2010 AD. Potential mission benefits include much shorter in-space times, reduced IMLEO requirements, and replenishment of supplies from in-situ resources.

Nectar replenishment maintains the neutral effects of nectar robbing on female reproductive success of Salvia przewalskii (Lamiaceae), a plant pollinated and robbed by bumble bees.

PubMed

Ye, Zhong-Ming; Jin, Xiao-Fang; Wang, Qing-Feng; Yang, Chun-Feng; Inouye, David W

2017-04-01

It has been suggested that the dynamics of nectar replenishment could differ for flowers after being nectar robbed or visited legitimately, but further experimental work is needed to investigate this hypothesis. This study aimed to assess the role of nectar replenishment in mediating the effects of nectar robbing on pollinator behaviour and plant reproduction. Plant-robber-pollinator interactions in an alpine plant, Salvia przewalskii , were studied. It is pollinated by long-tongued Bombus religiosus and short-tongued B. friseanus , but robbed by B. friseanus . Nectar production rates for flowers after they were either robbed or legitimately visited were compared, and three levels of nectar robbing were created to detect the effects of nectar robbing on pollinator behaviour and plant reproduction. Nectar replenishment did not differ between flowers that had been robbed or legitimately visited. Neither fruit set nor seed set was significantly affected by nectar robbing. In addition, nectar robbing did not significantly affect visitation rate, flowers visited within a plant per foraging bout, or flower handling time of the legitimate pollinators. However, a tendency for a decrease in relative abundance of the pollinator B. religiosus with an increase of nectar robbing was found. Nectar robbing did not affect female reproductive success because nectar replenishment ensures that pollinators maintain their visiting activity to nectar-robbed flowers. Nectar replenishment might be a defence mechanism against nectar robbing to enhance reproductive fitness by maintaining attractiveness to pollinators. Further studies are needed to reveal the potential for interference competition among bumble bees foraging as robbers and legitimate visitors, and to investigate variation of nectar robbing in communities with different bumble bee species composition. © The Author 2017. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Zinc Replenishment Reverses Overexpression of the Proinflammatory Mediator S100A8 and Esophageal Preneoplasia in the Rat

PubMed Central

Taccioli, Cristian; Wan, Shao-Gui; Liu, Chang-Gong; Alder, Hansjuerg; Volinia, Stefano; Farber, John L.; Croce, Carlo M.

2009-01-01

Background & Aims Zinc-deficiency is implicated in the pathogenesis of human esophageal cancer. In the rat esophagus, it induces cell proliferation, modulates genetic expression, and enhances carcinogenesis. Zinc-replenishment reverses proliferation and inhibits carcinogenesis. The zinc-deficient rat model allows the identification of biological differences affected by zinc during early esophageal carcinogenesis. Methods We evaluated gene expression profiles of esophageal epithelia from zinc-deficient and replenished rats versus sufficient rats using Affymetrix Rat Genome GeneChip. We characterized the role of the top-upregulated gene S100A8 in esophageal hyperplasia/reversal and in chemically-induced esophageal carcinogenesis in zinc-modulated animals by immunohistochemistry and real-time quantitative polymerase chain reaction. Results The hyperplastic deficient esophagus has a distinct expression signature with the proinflammation-gene S100A8 and S100A9 upregulated 57- and 5-fold. “Response to external stimulus” comprising S100A8 was the only significantly overrepresented biological pathway among the upregulated genes. Zinc-replenishment rapidly restored to control levels the expression of S100A8/A9 and 27 other genes and reversed the hyperplastic phenotype. With its receptor RAGE, co-localization and overexpression of S100A8 protein occurred in the deficient esophagus that overexpressed NF-κB p65 and COX-2 protein. Zinc-replenishment but not by a COX-2 inhibitor reduced the overexpression of these 4 proteins. Additionally, esophageal S100A8/A9 mRNA levels were directly associated with the diverse tumorigenic outcome in zinc-deficient and zinc-replenished rats. Conclusions In vivo zinc regulates S100A8 expression and modulates the link between S100A8-RAGE interaction and downstream NF-κB/COX-2 signaling. The finding that zinc regulates an inflammatory pathway in esophageal carcinogenesis may lead to prevention and therapy for this cancer. PMID:19111725

Farming with rocks and minerals: challenges and opportunities.

PubMed

Van Straaten, Peter

2006-12-01

In many parts of the world food security is at risk. One of the biophysical root causes of falling per-capita food production is the declining quality and quantity of soils. To reverse this trend and increase soil fertility soil and plant nutrients have to be replenished. This review provides a literature survey of experiences of using multi-nutrient rock fertilizers for soil fertility enhancement from temperate and tropical environments. Advantages and limitations of the application of rock fertilizers are discussed. Examples are provided from two successful nutrient replenishment projects in Africa where locally available rock fertilizers are used on highly leached acid soils. The potential of combining organic materials alongside rock fertilizers in soil fertility replenishment strategies is stressed.

Spatial structure and nutrients promote invasion of IncP-1 plasmids in bacterial populations

PubMed Central

Fox, Randal E; Zhong, Xue; Krone, Stephen M; Top, Eva M

2008-01-01

In spite of the importance of plasmids in bacterial adaptation, we have a poor understanding of their dynamics. It is not known if or how plasmids persist in and spread through (invade) a bacterial population when there is no selection for plasmid-encoded traits. Moreover, the differences in dynamics between spatially structured and mixed populations are poorly understood. Through a joint experimental/theoretical approach, we tested the hypothesis that self-transmissible IncP-1 plasmids can invade a bacterial population in the absence of selection when initially very rare, but only in spatially structured habitats and when nutrients are regularly replenished. Using protocols that differed in the degree of spatial structure and nutrient levels, the invasiveness of plasmid pB10 in Escherichia coli was monitored during at least 15 days, with an initial fraction of plasmid-bearing (p+) cells as low as 10−7. To further explore the mechanisms underlying plasmid dynamics, we developed a spatially explicit mathematical model. When cells were grown on filters and transferred to fresh medium daily, the p+ fraction increased to 13%, whereas almost complete invasion occurred when the population structure was disturbed daily. The plasmid was unable to invade in liquid. When carbon source levels were lower or not replenished, plasmid invasion was hampered. Simulations of the mathematical model closely matched the experimental results and produced estimates of the effects of alternative experimental parameters. This allowed us to isolate the likely mechanisms most responsible for the observations. In conclusion, spatial structure and nutrient availability can be key determinants in the invasiveness of plasmids. PMID:18528415

A Small Particle Solar Receiver for High Temperature Brayton Power Cycles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Fletcher John

The objective of this project is to design, construct, and test at the Sandia NSTTF a revolutionary high temperature air-cooled solar receiver in the multi-MW range that can be used to drive a gas turbine, to generate low-cost electricity at $.06/kWh when considered as part of an optimized CSP combined cycle system. The receiver being developed in this research uses a dilute suspension of selectively absorbing carbon nano-particles to absorb highly concentrated solar flux. The concept of a volumetric, selective, and continually replenishable absorber is unique in the solar field.

Analysis of dewar and transfer line cooldown in Superfluid Helium On-Orbit Transfer Flight Experiment (SHOOT)

NASA Technical Reports Server (NTRS)

Ng, Y. S.; Lee, J. H.

1989-01-01

The Superfluid Helium On-Orbit Transfer Flight Experiment (SHOOT) is designed to demonstrate the techniques and components required for orbital superfluid (He II) replenishment of observatories and satellites. One of the tasks planned in the experiment is to cool a warm cryogen tank and a warm transfer line to liquid helium temperature. A math model, based on single-phase vapor flow heat transfer, has been developed to predict the cooldown time, component temperature histories, and helium consumption rate, for various initial conditions of the components and for the thermomechanical pump heater powers of 2 W and 0.5 W. This paper discusses the model and the analytical results, which can be used for planning the experiment operations and determining the pump heater power required for the cooldown operation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furey, M.J.; Kajdas, C.; Kaltenbach, K.W.

Advanced lubrication technologies based on the concept of tribopolymerization as a mechanism of boundary lubrication are described. Advantages of this approach as well as potential applications which could have an impact on the design, manufacture, and performance of existing and future automotive engines are presented and discussed. Tribopolymerization, a novel concept of molecular design developed by Furey and Kajdas, involves the continuous formation of thin polymeric films on rubbing surfaces; the protective films formed are self-replenishing. The antiwear compounds developed from this technology are effective with metals as well as ceramics and in the liquid as well as vapor phases.more » Furthermore, they are ashless and contain no harmful phosphorus or sulfur; and many are biodegradable. Thus, potential applications of this technology are diverse and include a variety of cost/performance/energy/environmental advantages. Examples include the following: (a) machining and cutting applications using thin films to reduce friction and ceramic tool wear; (b) the lubrication of ceramic engines (e.g., low heat rejection diesel engines) or ceramic components; (c) the development of ashless lubricants for existing and future automotive engines to reduce exhaust catalyst poisoning and environmental emissions; (d) ashless antiwear or ``lubricity`` additives for fuels, including gasoline, diesel and jet fuel; (e) vapor phase applications of this technology to high temperature gaseous systems or to fuel injector wear problems associated with the use of natural gas engines; and (f) the use of the concept of tribopolymerization as an enabling technology in the development of new engines and new automotive propulsion systems.« less

Assimilation of granite by basaltic magma at Burnt Lava flow, Medicine Lake volcano, northern California: Decoupling of heat and mass transfer

USGS Publications Warehouse

Grove, T.L.; Kinzler, R.J.; Baker, M.B.; Donnelly-Nolan, J. M.; Lesher, C.E.

1988-01-01

At Medicine Lake volcano, California, andesite of the Holocene Burnt Lava flow has been produced by fractional crystallization of parental high alumina basalt (HAB) accompanied by assimilation of granitic crustal material. Burnt Lava contains inclusions of quenched HAB liquid, a potential parent magma of the andesite, highly melted granitic crustal xenoliths, and xenocryst assemblages which provide a record of the fractional crystallization and crustal assimilation process. Samples of granitic crustal material occur as xenoliths in other Holocene and Pleistocene lavas, and these xenoliths are used to constrain geochemical models of the assimilation process. A large amount of assimilation accompanied fractional crystallization to produce the contaminated Burnt lava andesites. Models which assume that assimilation and fractionation occurred simultaneously estimate the ratio of assimilation to fractional crystallization (R) to be >1 and best fits to all geochemical data are at an R value of 1.35 at F=0.68. Petrologic evidence, however, indicates that the assimilation process did not involve continuous addition of granitic crust as fractionation occurred. Instead, heat and mass transfer were separated in space and time. During the assimilation process, HAB magma underwent large amounts of fractional crystallization which was not accompanied by significant amounts of assimilation. This fractionation process supplied heat to melt granitic crust. The models proposed to explain the contamination process involve fractionation, replenishment by parental HAB, and mixing of evolved and parental magmas with melted granitic crust. ?? 1988 Springer-Verlag.

Modelling of a Convecting, Crystallizing, and Replenished Diopside-Anorthite Axial Magma Chamber beneath Mid Ocean Ridges

NASA Astrophysics Data System (ADS)

Lowell, R. P.; Lata, C.

2016-12-01

The aim of this work is to model heat output from a cooling, convective, crystallizing, and replenished basaltic magma sill, representing an axial magma lens (AML) at mid oceanic ridges. As a simplified version of basaltic melt, we have assumed the melt to be a two-component eutectic system composed of diopside and anorthite. Convective vigor is expressed through the Rayleigh number and heat flux is scaled through a classical relationship between the Rayleigh number and Nusselt number, where the temperature difference driving the convective heat flux is derived from a "viscous" temperature scale reflecting the strong temperature dependent viscosity of the system. Viscosity is modeled as a function of melt composition and temperature using the Tammann-Vogel-Fulcher equation, with parameters fit to the values of observed viscosities along the diopside-anorthite liquidus. It was observed for the un-replenished case, in which crystals fall rapidly to the floor of the AML, model results show that the higher initial concentration of diopside, the more vigorous the convection and the faster the rate of crystallization and decay of heat output. Replenishment of the AML accompanied by modest thickening of the melt layer stabilizes the heat output at values similar to those observed at ridge-axis hydrothermal systems. This study is an important step forward in quantitative understanding of thermal evolution of the axial magma lens at a mid-ocean ridge and the corresponding effect on high-temperature hydrothermal systems. Future work could involve improved replenishment mechanisms, more complex melts, and direct coupling with hydrothermal circulation models.

Possible precipitation of ice at low latitudes of Mars during periods of high obliquity

USGS Publications Warehouse

Jakosky, B.M.; Carr, M.H.

1985-01-01

Most of the old cratered highlands of Mars are dissected by branching river valleys that appear to have been cut by running water1,2 yet liquid water is unstable everywhere on the martian surface. In the equatorial region, where most of the valleys are observed, even ice is unstable3,4. It has been suggested, therefore, that Mars had an early denser atmosphere with sufficient greenhouse warming to allow the existence of liquid water 5. Here, we suggest instead that during periods of very high obliquities, ice could accumulate at low latitudes as a result of sustained sublimation of ice from the poles and transport of the water vapour equatorwards. At low latitudes, the water vapour would saturate the atmosphere and condense onto the surface where it would accumulate until lower obliquities prevailed. The mechanism is efficient only at the very high obliquities that occurred before formation of Tharsis very early in the planet's history, but limited equatorial ice accumulation could also have occurred at the highest obliquities during the rest of the planet's history. Partial melting of the ice could have provided runoff to form the channels or replenish the groundwater system. ?? 1985 Nature Publishing Group.

Nanoparticle-wetted surfaces for relays and energy transmission contacts.

PubMed

Voevodin, Andrey A; Vaia, Richard A; Patton, Steven T; Diamanti, Steven; Pender, Mark; Yoonessi, Mitra; Brubaker, Jennifer; Hu, Jian-Jun; Sanders, Jeffrey H; Phillips, Benjamin S; MacCuspie, Robert I

2007-11-01

Submonolayer coatings of noble-metal nanoparticle liquids (NPLs) are shown to provide replenishable surfaces with robust asperities and metallic conductivity that extends the durability of electrical relays by 10 to 100 times (depending on the current driven through the contact) as compared to alternative approaches. NPLs are single-component materials consisting of a metal nanoparticle core (5-20 nm Au or Pt nanoparticles) surrounded by a covalently tethered ionic-liquid corona of 1.5 to 2 nm. Common relay failure modes, such as stiction, surface distortion, and contact shorting, are suppressed with the addition of a submonolayer of NPLs to the contact surfaces. This distribution of NPLs results in a force profile for a contact-retraction cycle that is distinct from bare Au contacts and thicker, multilayer coatings of NPLs. Postmortem examination reveals a substantial decrease in topological change of the electrode surface relative to bare contacts, as well as an indication of lateral migration of the nanoparticles from the periphery towards the contact. A general extension of this concept to dynamic physical interfaces experiencing impact, sliding, or rolling affords alternatives to increase reliability and reduced losses for transmittance of electrical and mechanical energy.

Increasing Boiling Heat Transfer using Low Conductivity Materials

PubMed Central

Mahamudur Rahman, Md; Pollack, Jordan; McCarthy, Matthew

2015-01-01

We report the counterintuitive mechanism of increasing boiling heat transfer by incorporating low-conductivity materials at the interface between the surface and fluid. By embedding an array of non-conductive lines into a high-conductivity substrate, in-plane variations in the local surface temperature are created. During boiling the surface temperature varies spatially across the substrate, alternating between high and low values, and promotes the organization of distinct liquid and vapor flows. By systematically tuning the peak-to-peak wavelength of this spatial temperature variation, a resonance-like effect is seen at a value equal to the capillary length of the fluid. Replacing ~18% of the surface with a non-conductive epoxy results in a greater than 5x increase in heat transfer rate at a given superheat temperature. This drastic and counterintuitive increase is shown to be due to optimized bubble dynamics, where ordered pathways allow for efficient removal of vapor and the return of replenishing liquid. The use of engineered thermal gradients represents a potentially disruptive approach to create high-efficiency and high-heat-flux boiling surfaces which are naturally insensitive to fouling and degradation as compared to other approaches. PMID:26281890

Possible precipitation of ice at low latitudes of Mars during periods of high obliquity

NASA Technical Reports Server (NTRS)

Jakosky, B. M.; Carr, M. H.

1985-01-01

Most of the old cratered highlands of Mars are dissected by branching river valleys that appear to have been cut by running water, yet liquid water is unstable everywhere on the Martian surface. In the equatorial region, where most of the valleys are observed, even ice is unstable. It has been suggested, therefore, that Mars had an early denser atmosphere with sufficient greenhouse warming to allow the existence of liquid water. Here, it is suggested instead that during periods of very high obliquities, ice could accumulate at low latitudes as a result of sustained sublimation of ice from the poles and transport of the water vapor equatorwards. At low latitudes, the water vapor would saturate the atmosphere and condense onto the surface, where it would accumulate until lower obliquities prevailed. The mechanism is efficient only at the very high obliquities that occurred before formation of Tharsis very early in the planet's history, but limited equatorial ice accumulation could also have occurred at the highest obliquities during the rest of the planet's history. Partial melting of the ice could have provided runoff to form the channels or replenish the groundwater system.

Understanding time use, stress and recovery practices among early career physicians: an exploratory study.

PubMed

Cranley, Nicole M; Cunningham, Christopher J L; Panda, Mukta

2016-01-01

Early career physicians (ECPs) work an average of 80 h per week, and at times may approach 24 continuous hours working. These hours, combined with a stressful work environment, and an inability to physically and psychologically detach from work make ECPs likely to experience burnout and other negative health-related consequences. This study provides insight into the stress and recovery challenges faced by ECPs in a typical hospital environment. Rich qualitative and quantitative data were gathered from participants regarding daily time usage, and recovery practices and needs. ECPs report longer working hours, less leisure time and shorter amounts of sleep than average working adults. ECPs do not participate in many resource-replenishing activities while at work, and when out of work, they tend to participate in more passive than active forms of recovery. Resource-draining activities were identified as requiring much of ECP's nonwork time, further limiting recovery. The prevention of burnout and other negative health consequences among ECPs requires the building of a workplace and educational culture that supports regular resource replenishment. This includes the need for a curriculum of medical education that teaches ECPs to identify the signs of stress and recovery needs, and how to effectively address these needs.

2009 Munitions Executive Summit

DTIC Science & Technology

2009-02-05

CURRENT OPERATIONS • Replenish stocks expended in operations • Build /Replenish War Reserve stocks • Modernize stocks in the process • Industrial Base...4 Steel-Consuming Markets Construction (40% - 45%) Appliances, Office Furniture (2.5%) Containers (4%) Industrial Equipment (15% - 18...Partnership - HPS for Bridges • U.S. Navy • FHWA • AISI Steel and Defense Industries Collaboration – High- Performance Steels 17 Major

Effects of landscape composition and configuration on migrating songbirds: inference from and individual-based model

Treesearch

Emily Cohen; Scott Pearson; Frank Moore

2014-01-01

The behavior of long-distance migrants during stopover is constrained by the need to quickly and safely replenish energetic reserves. Replenishing fuel stores at stopover sites requires adjusting to unfamiliar landscapes with little to no information about the distribution of resources. Despite their critical importance to the success of songbird migration, the effects...

Army Logistician. Volume 41, Issue 3, May-June 2009

DTIC Science & Technology

2009-06-01

analyzing, and executing multifunc- tional logistics, including transportation, food service, and acquisition, receipt, issue, and recovery of Govern...internal gun truck security for presence patrols, com- bat replenishment operations, recovery operations for damaged vehicles, or escort operations for...the next mission. During our 14-month deployment, the gun truck pla- toon provided security for 208 combat replenishment operations, 27 recovery

Developing a Continuous Bioprocessing Approach to Stromal Cell Manufacture.

PubMed

Miotto, Martina; Gouveia, Ricardo; Abidin, Fadhilah Zainal; Figueiredo, Francisco; Connon, Che J

2017-11-29

To this day, the concept of continuous bioprocessing has been applied mostly to the manufacture of molecular biologics such as proteins, growth factors, and secondary metabolites with biopharmaceutical uses. The present work now sets to explore the potential application of continuous bioprocess methods to source large numbers of human adherent cells with potential therapeutic value. To this purpose, we developed a smart multifunctional surface coating capable of controlling the attachment, proliferation, and subsequent self-detachment of human corneal stromal cells. This system allowed the maintenance of cell cultures under steady-state growth conditions, where self-detaching cells were continuously replenished by the proliferation of those remaining attached. This facilitated a closed, continuous bioprocessing platform with recovery of approximately 1% of the total adherent cells per hour, a yield rate that was maintained for 1 month. Moreover, both attached and self-detached cells were shown to retain their original phenotype. Together, these results represent the proof-of-concept for a new high-throughput, high-standard, and low-cost biomanufacturing strategy with multiple potentials and important downstream applications.

Atomizing, continuous, water monitoring module

DOEpatents

Thompson, C.V.; Wise, M.B.

1997-07-08

A system for continuously analyzing volatile constituents of a liquid is described. The system contains a pump for continuously pumping the liquid to be tested at a predetermined flow rate into an extracting container through a liquid directing tube having an orifice at one end and positioned to direct the liquid into the extracting container at a flow rate sufficient to atomize the liquid within the extracting container. A continuous supply of helium carrier gas at a predetermined flow rate is directed through a tube into the extracting container and co-mingled with the atomized liquid to extract the volatile constituents contained within the atomized liquid. The helium containing the extracted volatile constituents flows out of the extracting container into a mass spectrometer for an analysis of the volatile constituents of the liquid. 3 figs.

Atomizing, continuous, water monitoring module

DOEpatents

Thompson, Cyril V.; Wise, Marcus B.

1997-01-01

A system for continuously analyzing volatile constituents of a liquid is described. The system contains a pump for continuously pumping the liquid to be tested at a predetermined flow rate into an extracting container through a liquid directing tube having an orifice at one end and positioned to direct the liquid into the extracting container at a flow rate sufficient to atomize the liquid within the extracting container. A continuous supply of helium carrier gas at a predetermined flow rate is directed through a tube into the extracting container and co-mingled with the atomized liquid to extract the volatile constituents contained within the atomized liquid. The helium containing the extracted volatile constituents flows out of the extracting container into a mass spectrometer for an analysis of the volatile constituents of the liquid.

Crystallization of oxidized, moderately hydrous arc basalt at mid- to lower-crustal pressures: implications for andesite genesis

NASA Astrophysics Data System (ADS)

Blatter, Dawnika L.; Sisson, Thomas W.; Hankins, W. Ben

2013-09-01

This study focuses on the production of convergent margin calc-alkaline andesites by crystallization-differentiation of basaltic magmas in the lower to middle crust. Previous experimental studies show that dry, reduced, subalkaline basalts differentiate to tholeiitic (high Fe/Mg) daughter liquids, but the influences of H2O and oxidation on differentiation are less well established. Accordingly, we performed crystallization experiments at controlled oxidized fO2 (Re-ReO2 ≈ ΔNi-NiO + 2) on a relatively magnesian basalt (8.7 wt% MgO) typical of mafic magmas erupted in the Cascades near Mount Rainier, Washington. The basalt was synthesized with 2 wt% H2O and run at 900, 700, and 400 MPa and 1,200 to 950 °C. A broadly clinopyroxenitic crystallization interval dominates near the liquidus at 900 and 700 MPa, consisting of augite + olivine + orthopyroxene + Cr-spinel (in decreasing abundance). With decreasing temperature, plagioclase crystallizes, Fe-Ti-oxide replaces spinel, olivine dissolves, and finally amphibole appears, producing gabbroic and then amphibole gabbroic crystallization stages. Enhanced plagioclase stability at lower pressure narrows the clinopyroxenitic interval and brings the gabbroic interval toward the liquidus. Liquids at 900 MPa track along Miyashiro's (Am J Sci 274(4):321-355, 1974) tholeiitic versus calc-alkaline boundary, whereas those at 700 and 400 MPa become calc-alkaline at silica contents ≥56 wt%. This difference is chiefly due to higher temperature appearance of magnetite (versus spinel) at lower pressures. Although the evolved liquids are similar in many respects to common calc-alkaline andesites, the 900 and 700 MPa liquids differ in having low CaO concentrations due to early and abundant crystallization of augite, with the result that those liquids become peraluminous (ASI: molar Al/(Na + K + 2Ca) > 1) at ≥61 wt% SiO2, similar to liquids reported in other studies of the high-pressure crystallization of hydrous basalts (Müntener and Ulmer in Geophys Res Lett 33(21):L21308, 2006). The lower-pressure liquids (400 MPa) have this same trait, but to a lesser extent due to more abundant near-liquidus plagioclase crystallization. A compilation of >6,500 analyses of igneous rocks from the Cascades and the Sierra Nevada batholith, representative of convergent margin (arc) magmas, shows that ASI increases continuously and linearly with SiO2 from basalts to rhyolites or granites and that arc magmas are not commonly peraluminous until SiO2 exceeds 69 wt%. These relations are consistent with plagioclase accompanying mafic silicates over nearly all the range of crystallization (or remelting). The scarcity of natural peraluminous andesites shows that progressive crystallization-differentiation of primitive basalts in the deep crust, producing early clinopyroxenitic cumulates and evolved liquids, does not dominate the creation of intermediate arc magmas or of the continental crust. Instead, mid- to upper-crustal differentiation and/or open-system processes are critical to the production of intermediate arc magmas. Primary among the open-system processes may be extraction of highly evolved (granitic, rhyolitic) liquids at advanced degrees of basalt solidification (or incipient partial melting of predecessor gabbroic intrusions) and mixing of such liquids into replenishing basalts. Furthermore, if the andesitic-composition continents derived from basaltic sources, the arc ASI-SiO2 relation shows that the mafic component returned to the mantle was gabbroic in composition, not pyroxenitic.

Crystallization of oxidized, moderately hydrous arc basalt at mid- to lower-crustal pressures: Implications for andesite genesis

USGS Publications Warehouse

Blatter, Dawnika L.; Sisson, Thomas W.; Hankins, W. Ben

2013-01-01

This study focuses on the production of convergent margin calc-alkaline andesites by crystallization–differentiation of basaltic magmas in the lower to middle crust. Previous experimental studies show that dry, reduced, subalkaline basalts differentiate to tholeiitic (high Fe/Mg) daughter liquids, but the influences of H2O and oxidation on differentiation are less well established. Accordingly, we performed crystallization experiments at controlled oxidized fO2 (Re–ReO2 ≈ ΔNi–NiO + 2) on a relatively magnesian basalt (8.7 wt% MgO) typical of mafic magmas erupted in the Cascades near Mount Rainier, Washington. The basalt was synthesized with 2 wt% H2O and run at 900, 700, and 400 MPa and 1,200 to 950 °C. A broadly clinopyroxenitic crystallization interval dominates near the liquidus at 900 and 700 MPa, consisting of augite + olivine + orthopyroxene + Cr-spinel (in decreasing abundance). With decreasing temperature, plagioclase crystallizes, Fe–Ti-oxide replaces spinel, olivine dissolves, and finally amphibole appears, producing gabbroic and then amphibole gabbroic crystallization stages. Enhanced plagioclase stability at lower pressure narrows the clinopyroxenitic interval and brings the gabbroic interval toward the liquidus. Liquids at 900 MPa track along Miyashiro’s (Am J Sci 274(4):321–355, 1974) tholeiitic versus calc-alkaline boundary, whereas those at 700 and 400 MPa become calc-alkaline at silica contents ≥56 wt%. This difference is chiefly due to higher temperature appearance of magnetite (versus spinel) at lower pressures. Although the evolved liquids are similar in many respects to common calc-alkaline andesites, the 900 and 700 MPa liquids differ in having low CaO concentrations due to early and abundant crystallization of augite, with the result that those liquids become peraluminous (ASI: molar Al/(Na + K + 2Ca) > 1) at ≥61 wt% SiO2, similar to liquids reported in other studies of the high-pressure crystallization of hydrous basalts (Müntener and Ulmer in Geophys Res Lett 33(21):L21308, 2006). The lower-pressure liquids (400 MPa) have this same trait, but to a lesser extent due to more abundant near-liquidus plagioclase crystallization. A compilation of >6,500 analyses of igneous rocks from the Cascades and the Sierra Nevada batholith, representative of convergent margin (arc) magmas, shows that ASI increases continuously and linearly with SiO2 from basalts to rhyolites or granites and that arc magmas are not commonly peraluminous until SiO2 exceeds 69 wt%. These relations are consistent with plagioclase accompanying mafic silicates over nearly all the range of crystallization (or remelting). The scarcity of natural peraluminous andesites shows that progressive crystallization–differentiation of primitive basalts in the deep crust, producing early clinopyroxenitic cumulates and evolved liquids, does not dominate the creation of intermediate arc magmas or of the continental crust. Instead, mid- to upper-crustal differentiation and/or open-system processes are critical to the production of intermediate arc magmas. Primary among the open-system processes may be extraction of highly evolved (granitic, rhyolitic) liquids at advanced degrees of basalt solidification (or incipient partial melting of predecessor gabbroic intrusions) and mixing of such liquids into replenishing basalts. Furthermore, if the andesitic-composition continents derived from basaltic sources, the arc ASI–SiO2 relation shows that the mafic component returned to the mantle was gabbroic in composition, not pyroxenitic.

Real time myocardial contrast echocardiography during supine bicycle stress and continuous infusion of contrast agent. Cutoff values for myocardial contrast replenishment discriminating abnormal myocardial perfusion.

PubMed

Miszalski-Jamka, Tomasz; Kuntz-Hehner, Stefanie; Schmidt, Harald; Hammerstingl, Christoph; Tiemann, Klaus; Ghanem, Alexander; Troatz, Clemens; Lüderitz, Berndt; Omran, Heyder

2007-07-01

Myocardial contrast echocardiography (MCE) is a new imaging modality for diagnosing coronary artery disease (CAD). The aim of our study was to evaluate feasibility of qualitative myocardial contrast replenishment (RP) assessment during supine bicycle stress MCE and find out cutoff values for such analysis, which could allow accurate detection of CAD. Forty-four consecutive patients, scheduled for coronary angiography (CA) underwent supine bicycle stress two-dimensional echocardiography (2DE). During the same session, MCE was performed at peak stress and post stress. Ultrasound contrast agent (SonoVue) was administered in continuous mode using an infusion pump (BR-INF 100, Bracco Research). Seventeen-segment model of left ventricle was used in analysis. MCE was assessed off-line in terms of myocardial contrast opacification and RP. RP was evaluated on the basis of the number of cardiac cycles required to refill the segment with contrast after its prior destruction with high-power frames. Determination of cutoff values for RP assessment was performed by means of reference intervals and receiver operating characteristic analysis. Quantitative CA was carried out using CAAS system. MCE could be assessed in 42 patients. CA revealed CAD in 25 patients. Calculated cutoff values for RP-analysis (peak-stress RP >3 cardiac cycles and difference between peak stress and post stress RP >0 cardiac cycles) provided sensitive (88%) and accurate (88%) detection of CAD. Sensitivity and accuracy of 2DE were 76% and 79%, respectively. Qualitative RP-analysis based on the number of cardiac cycles required to refill myocardium with contrast is feasible during supine bicycle stress MCE and enables accurate detection of CAD.

Preliminary Experimental Results on the Technique of Artificial River Replenishment to Mitigate Sediment Loss Downstream Dams

NASA Astrophysics Data System (ADS)

Franca, M. J.; Battisacco, E.; Schleiss, A. J.

2014-12-01

The transport of sediments by water throughout the river basins, from the steep slopes of the upstream regions to the sea level, is recognizable important to keep the natural conditions of rivers with a role on their ecology processes. Over the last decades, a reduction on the supply of sand and gravel has been observed downstream dams existing in several alpine rivers. Many studies highlight that the presence of a dam strongly modifies the river behavior in the downstream reach, in terms of morphology and hydrodynamics, with consequences on local ecology. Sediment deficit, bed armoring, river incision and bank instability are the main effects which affect negatively the aquatic habitats and the water quality. One of the proposed techniques to solve the problem of sediment deficit downstream dams, already adopted in few Japanese and German rivers although on an unsatisfactory fashion, is the artificial replenishment of these. Generally, it was verified that the erosion of the replenishments was not satisfactory and the transport rate was not enough to move the sediments to sufficient downstream distances. In order to improve and to provide an engineering answer to make this technique more applicable, a series of laboratory tests are ran as preparatory study to understand the hydrodynamics of the river flow when the replenishment technique is applied. Erodible volumes, with different lengths and submergence conditions, reproducing sediment replenishments volumes, are positioned along a channel bank. Different geometrical combinations of erodible sediment volumes are tested as well on the experimental flume. The first results of the experimental research, concerning erosion time evolution, the influence of discharge and the distance travelled by the eroded sediments, will be presented and discussed.

Synchronization of construction, replenishment and leasing cycles with account of wave dynamics of innovation cycles in the construction and transport field

NASA Astrophysics Data System (ADS)

Alekseeva, Tatyana

2017-10-01

The article considers the contradictive nature of the basic cycles of the growth in construction, the core of which are construction cycles, replenishment cycles of the active part of fixed assets, innovation and investment cycles. All of the listed cycles objectively thwart the science and technology progress in construction. There are presented results of the study of finance leasing as an effective tool, that provides time reduction of the innovation replenishment cycle of the active part of fixed assets in construction. It takes into account the development and implementation terms of construction investment projects in order to timely support the innovation wave and enhance its efficiency in construction for a rapid transition of the construction investment complex and national economy to a new vector of growth.

Characterization of dopamine releasable and reserve pools in Drosophila larvae using ATP/P2X2-mediated stimulation

PubMed Central

Xiao, Ning; Venton, B. Jill

2015-01-01

Dopaminergic signaling pathways are conserved between mammals and Drosophila, but the factors important for maintaining the functional pool of synaptic dopamine are not fully understood in Drosophila. In this study, we characterized the releasable and reserve dopamine pools in Drosophila larvae using ATP/ P2X2-mediated stimulation. Dopamine release was stable with stimulations performed at least every 5 min but decayed with stimulations performed 2 min apart or less, indicating the replenishment of the releasable pool occurred on a time scale between 2 and 5 min. Dopamine synthesis or uptake were pharmacologically inhibited with 3-iodotyrosine and cocaine, respectively, to evaluate their contributions to maintaining the releasable dopamine pool. We found that both synthesis and uptake were needed to maintain the releasable dopamine pool, with synthesis playing a major part in long-term replenishment and uptake being more important for short-term replenishment. These effects of synthesis and uptake on different time scales in Drosophila are analogous to mammals. However, unlike in mammals, cocaine did not activate a reserve pool of dopamine in Drosophila when using P2X2 stimulations. Our study shows that both synthesis and uptake replenish the releasable pool, providing a better understanding of dopamine regulation in Drosophila. PMID:25951875

Generous-like flowers: nectar production in two epiphytic bromeliads and a meta-analysis of removal effects.

PubMed

Ordano, Mariano; Ornelas, Juan Francisco

2004-08-01

Animal-pollinated angiosperm plants that respond positively to nectar removal by replenishment invest energy that can entail a reproductive cost. We investigated whether or not nectar removal stimulates replenishment in two hummingbird-pollinated bromeliad species. Nectar replenishment rates were also assessed by removing nectar from manually pollinated flowers because pollination events might be used as signals to save energy by preventing allocation to post-pollination nectar production. Then we synthesized the current understanding of nectar removal effects by reviewing existing published studies with a meta-analysis. The magnitude and significance of estimated nectar removal effects and factors associated with variation in size and direction of nectar removal effects were elucidated with the meta-analysis. We found that both Tillandsia species strongly respond to repeated nectar removal by producing >3 times additional nectar. Nectar secretion patterns were not altered by pollination (stigmatic pollen deposition) and we found no evidence of nectar reabsorption. Although the effect size varied widely across systems and/or environmental conditions, the meta-analysis showed that nectar removal had overall a positive effect on nectar replenishment (mainly among species inhabiting wet tropical habitats such as Tillandsia), and a negative effect on the secretion of additional sugar, suggesting that those plants are resource limited and conservative in the secretion of additional sugar.

The role of the geothermal gradient in the emplacement and replenishment of ground ice on Mars

NASA Technical Reports Server (NTRS)

Clifford, Stephen M.

1993-01-01

Knowledge of the mechanisms by which ground ice is emplaced, removed, and potentially replenished, are critical to understanding the climatic and hydrologic behavior of water on Mars, as well as the morphologic evolution of its surface. Because of the strong temperature dependence of the saturated vapor pressure of H2O, the atmospheric emplacement or replenishment of ground ice is prohibited below the depth at which crustal temperatures begin to monotonically increase due to geothermal heating. In contrast, the emplacement and replenishment of ground ice from reservoirs of H2O residing deep within the crust can occur by at least three different thermally-driven processes, involving all three phases of water. In this regard, Clifford has discussed how the presence of a geothermal gradient as small as 15 K/km can give rise to a corresponding vapor pressure gradient sufficient to drive the vertical transport of 1 km of water from a reservoir of ground water at depth to the base of the cryosphere every 10(exp 6) - 10(exp 7) years. This abstract expands on this earlier treatment by considering the influence of thermal gradients on the transport of H2O at temperatures below the freezing point.

Method and apparatus for continuous flow injection extraction analysis

DOEpatents

Hartenstein, Steven D.; Siemer, Darryl D.

1992-01-01

A method and apparatus for a continuous flow injection batch extraction aysis system is disclosed employing extraction of a component of a first liquid into a second liquid which is a solvent for a component of the first liquid, and is immiscible with the first liquid, and for separating the first liquid from the second liquid subsequent to extraction of the component of the first liquid.

A Flexible System for Cultivation of Methanococcus and Other Formate-Utilizing Methanogens

PubMed Central

Wang, Liangliang; Lupa, Boguslaw

2017-01-01

Many hydrogenotrophic methanogens use either H2 or formate as the major electron donor to reduce CO2 for methane production. The conventional cultivation of these organisms uses H2 and CO2 as the substrate with frequent replenishment of gas during growth. H2 is explosive and requires an expensive gassing system to handle safely. Formate is as an ideal alternative substrate from the standpoints of both economy and safety but leads to large changes in the culture pH during growth. Here, we report that glycylglycine is an inexpensive and nontoxic buffer suitable for growth of Methanococcus maripaludis and Methanothermococcus okinawensis. This cultivation system is suitable for growth on liquid as well as solid medium in serum bottles. Moreover, it allows cultivation of liter scale cultures without expensive fermentation equipment. This formate cultivation system provides an inexpensive and flexible alternative for the growth of formate-utilizing, hydrogenotrophic methanogens. PMID:29348732

Laser-driven proton and deuteron acceleration from a pure solid-density H2/D2 cryogenic jet

NASA Astrophysics Data System (ADS)

Kim, Jongjin; Gauthier, Maxence; Aurand, Bastian; Curry, Chandra; Goede, Sebastian; Goyon, Clement; Williams, Jackson; Kerr, Shaun; Ruby, John; Propp, Adrienne; Ramakrishna, Bhuvanesh; Pak, Art; Hazi, Andy; Glenzer, Siegfried; Roedel, Christian

2015-11-01

Laser-driven proton acceleration has become of tremendous interest for the fundamental science and the potential applications in tumor therapy and proton radiography. We have developed a cryogenic liquid hydrogen jet, which can deliver a self-replenishing target of pure solid-density hydrogen or deuterium. This allows for a target compatible with high-repetition-rate experiments and results in a pure hydrogen plasma, facilitating comparison with simulations. A new modification has allowed for the formation of jets with rectangular profiles, facilitating comparison with foil targets. This jet was installed at the Titan laser and driven by laser pulses of 40-60 J of 527 nm laser light in 1 ps. The resulting proton and deuteron spectra were measured in multiple directions with Thomson parabola spectrometers and RCF stacks. The spectral and angular information suggest contribution from both the TNSA and RPA acceleration mechanisms.

Oxidation state of the Earth's upper mantle during the last 3800 million years: Implications for the origin of life

NASA Technical Reports Server (NTRS)

Delano, J. W.

1993-01-01

A popular, as well as scientifically rigorous, scenario for the origin of life on Earth involves the production of organic molecules by interaction of lightning (or other forms of energy) with a chemically reducing atmosphere in the early history of Earth. Experiments since the 1950's have convincingly demonstrated that the yield of organic molecules is high when the atmosphere contains molecular hydrogen, methane, ammonia, and water vapor. Additional work has also shown that such a highly reducing atmosphere might not, however, have been sufficiently long-lived in the presence of intense solar ultraviolet radiation for life to have formed from it. One way of maintaining such an atmosphere would be to have a continual replenishment of the reduced gases by prolonged volcanic outgassing from a reducing of Earth's interior. The length of time that this replenishment might need to continue is in part constrained by the flux of asteroids onto the Earth's surface containing sufficient energy to destroy most, if not all, life that had developed up to that point in time. If a reducing atmosphere is a key ingredient for the origin of life on Earth, the time of the last environmental sterilization due to large impacts would be an important constraint. In a deep marine setting (e.g., hydrothermal vent), the last global sterilization might have occurred at 4200-4000 Ma. On the Earth's surface, the last global sterilization event might have occurred at 4000-3700 Ma. If these are meaningful constraints, how likely is it that a reducing atmosphere could have survived on the Earth until about 3800 Ma ago? Due to the importance of replenishing this atmosphere with reducing components by volcanic outgassing from the mantle, geochemical information on the history of the mantle's oxidation state would be useful for addressing this question. Geochemical and experimental data discussed in this abstract suggest that extrusive mafic volcanics derived from the upper mantle have had oxidation states near the fayalite-magnetite quartz buffer throughout the last 3800 Ma. At magmatic temperatures, the gases released from volcanoes having this oxidation state would have been, as they are today, composed dominantly of carbon dioxide and water vapor, and would not contain the ingredients for maintaining a reducing atmosphere. Consequently, geochemical data do not favor the survival of a reducing atmosphere until about 3800 Ma. Alternative venues and pathways for the origin of life need to be investigated (e.g., hydrothermal vents along oceanic ridges).

Device for providing high-intensity ion or electron beam

DOEpatents

McClanahan, Edwin D.; Moss, Ronald W.

1977-01-01

A thin film of a low-thermionic-work-function material is maintained on the cathode of a device for producing a high-current, low-pressure gas discharge by means of sputter deposition from an auxiliary electrode. The auxiliary electrode includes a surface with a low-work-function material, such as thorium, uranium, plutonium or one of the rare earth elements, facing the cathode but at a disposition and electrical potential so as to extract ions from the gas discharge and sputter the low-work-function material onto the cathode. By continuously replenishing the cathode film, high thermionic emissions and ion plasmas can be realized and maintained over extended operating periods.

Marangoni and Gibbs elasticity of flowing soap films

NASA Astrophysics Data System (ADS)

Kim, Ildoo; Sane, Aakash; Mandre, Shreyas

2017-11-01

A flowing soap film has two elasticities. Marangoni elasticity dynamically stabilizes the film from sudden disturbance, and Gibbs elasticity is an equilibrium property that influences the film's persistence over time. In our experimental investigation, we find that Marangoni elasticity is 22 mN/m independent of the film thickness. On the other hand, Gibbs elasticity depends both on the film thickness and the soap concentration. Interestingly, the soap film made of dilute soap solution has the greater Gibbs elasticity, which is not consistent to the existing theory. Such discrepancy is originated from the flowing nature of our soap films, in which surfactants are continuously replenished.

Dye laser amplifier including a dye cell contained within a support vessel

DOEpatents

Davin, James

1992-01-01

A large (high flow rate) dye laser amplifier in which a continous replenished supply of dye is excited by a first light beam, specifically a copper vapor laser beam, in order to amplify the intensity of a second different light beam, specifically a dye beam, passing through the dye is disclosed herein. This amplifier includes a dye cell defining a dye chamber through which a continuous stream of dye is caused to pass at a flow rate of greater than 30 gallons/minute at a static pressure greater than 150 pounds/square inch and a specifically designed support vessel for containing the dye cell.

Rapid metabolism of exogenous angiotensin II by catecholaminergic neuronal cells in culture media.

PubMed

Basu, Urmi; Seravalli, Javier; Madayiputhiya, Nandakumar; Adamec, Jiri; Case, Adam J; Zimmerman, Matthew C

2015-02-01

Angiotensin II (AngII) acts on central neurons to increase neuronal firing and induce sympathoexcitation, which contribute to the pathogenesis of cardiovascular diseases including hypertension and heart failure. Numerous studies have examined the precise AngII-induced intraneuronal signaling mechanism in an attempt to identify new therapeutic targets for these diseases. Considering the technical challenges in studying specific intraneuronal signaling pathways in vivo, especially in the cardiovascular control brain regions, most studies have relied on neuronal cell culture models. However, there are numerous limitations in using cell culture models to study AngII intraneuronal signaling, including the lack of evidence indicating the stability of AngII in culture media. Herein, we tested the hypothesis that exogenous AngII is rapidly metabolized in neuronal cell culture media. Using liquid chromatography-tandem mass spectrometry, we measured levels of AngII and its metabolites, Ang III, Ang IV, and Ang-1-7, in neuronal cell culture media after administration of exogenous AngII (100 nmol/L) to a neuronal cell culture model (CATH.a neurons). AngII levels rapidly declined in the media, returning to near baseline levels within 3 h of administration. Additionally, levels of Ang III and Ang-1-7 acutely increased, while levels of Ang IV remained unchanged. Replenishing the media with exogenous AngII every 3 h for 24 h resulted in a consistent and significant increase in AngII levels for the duration of the treatment period. These data indicate that AngII is rapidly metabolized in neuronal cell culture media, and replenishing the media at least every 3 h is needed to sustain chronically elevated levels. © 2015 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of the American Physiological Society and The Physiological Society.

CONTINUOUS ANALYZER UTILIZING BOILING POINT DETERMINATION

DOEpatents

Pappas, W.S.

1963-03-19

A device is designed for continuously determining the boiling point of a mixture of liquids. The device comprises a distillation chamber for boiling a liquid; outlet conduit means for maintaining the liquid contents of said chamber at a constant level; a reflux condenser mounted above said distillation chamber; means for continuously introducing an incoming liquid sample into said reflux condenser and into intimate contact with vapors refluxing within said condenser; and means for measuring the temperature of the liquid flowing through said distillation chamber. (AEC)

Planning for Follow-On Spare Part Support by the Naval Electronic Systems Command.

DTIC Science & Technology

1984-06-01

System Replenishment Spare Parts", by Edward J. Brost , Air Force Institute of Technology [17]_ The objective of this study was to determine the...Competition in the Acquisition of Replenishment Spare Parts, M.S. Thesis, Air Force Institute of Technology, WPAFB, Ohio, September 1983. 17. Brost ...Instruction 4000.6D, Integrated Logistic Support (ILS); policy and responsibilities. 21 July 1983. 20. Mr. George Hughes, NAVELEX Code 81234

Cerebellar Granule Cell Replenishment Post-Injury by Adaptive Reprogramming of Nestin+ Progenitors

PubMed Central

Wojcinski, Alexandre; Lawton, Andrew K.; Bayin, N Sumru.; Lao, Zhimin; Stephen, Daniel N.; Joyner, Alexandra L.

2017-01-01

Regeneration of several organs involves adaptive reprogramming of progenitors, however, the intrinsic capacity of the developing brain to replenish lost cells remains largely unknown. In this study, we discovered that the developing cerebellum has unappreciated progenitor plasticity, since it undergoes near full growth and functional recovery following acute depletion of granule cells, the most plentiful neuron population in the brain. We demonstrate that following postnatal ablation of granule cell progenitors, Nestin-expressing progenitors (NEPs) specified during mid-embryogenesis to produce astroglia and interneurons, switch their fate and generate granule neurons in mice. Moreover, Hedgehog-signaling in two NEP populations is crucial not only for the compensatory replenishment of granule neurons but also to scale interneuron and astrocyte numbers. Thus we provide insights into the mechanisms underlying robustness of circuit formation in the cerebellum, and speculate that adaptive reprogramming of progenitors in other brain regions plays a greater role than appreciated in developmental regeneration. PMID:28805814

Study of communications data compression methods

NASA Technical Reports Server (NTRS)

Jones, H. W.

1978-01-01

A simple monochrome conditional replenishment system was extended to higher compression and to higher motion levels, by incorporating spatially adaptive quantizers and field repeating. Conditional replenishment combines intraframe and interframe compression, and both areas are investigated. The gain of conditional replenishment depends on the fraction of the image changing, since only changed parts of the image need to be transmitted. If the transmission rate is set so that only one fourth of the image can be transmitted in each field, greater change fractions will overload the system. A computer simulation was prepared which incorporated (1) field repeat of changes, (2) a variable change threshold, (3) frame repeat for high change, and (4) two mode, variable rate Hadamard intraframe quantizers. The field repeat gives 2:1 compression in moving areas without noticeable degradation. Variable change threshold allows some flexibility in dealing with varying change rates, but the threshold variation must be limited for acceptable performance.

Source replenishment device for vacuum deposition

DOEpatents

Hill, Ronald A.

1988-01-01

A material source replenishment device for use with a vacuum deposition apparatus. The source replenishment device comprises an intermittent motion producing gear arrangement disposed within the vacuum deposition chamber. An elongated rod having one end operably connected to the gearing arrangement is provided with a multiarmed head at the opposite end disposed adjacent the heating element of the vacuum deposition apparatus. An inverted U-shaped source material element is releasably attached to the outer end of each arm member whereby said multiarmed head is moved to locate a first of said material elements above said heating element, whereupon said multiarmed head is lowered to engage said material element with the heating element and further lowered to release said material element on the heating element. After vaporization of said material element, second and subsequent material elements may be provided to the heating element without the need for opening the vacuum deposition apparatus to the atmosphere.

Source replenishment device for vacuum deposition

DOEpatents

Hill, R.A.

1986-05-15

A material source replenishment device for use with a vacuum deposition apparatus is described. The source replenishment device comprises an intermittent motion producing gear arrangement disposed within the vacuum deposition chamber. An elongated rod having one end operably connected to the gearing arrangement is provided with a multiarmed head at the opposite end disposed adjacent the heating element of the vacuum deposition apparatus. An inverted U-shaped source material element is releasably attached to the outer end of each arm member whereby said multiarmed head is moved to locate a first of said material elements above said heating element, whereupon said multiarmed head is lowered to engage said material element with the heating element and further lowered to release said material element on the heating element. After vaporization of said material element, second and subsequent material elements may be provided to the heating element without the need for opening the vacuum deposition apparatus to the atmosphere.

Stability assessment of the chemical composition of the treated mining water used to replenish the cooling circuit in Jaworzno III Power Plant - Power Plant II

NASA Astrophysics Data System (ADS)

Karpiński, Marcin; Kmiecik, Ewa

2017-11-01

In Poland, electricity is still produced mainly in conventional power plants where fuel and water are materials necessary to generate the electricity. Even in modern power plants operating according to the principles of the sustainable development, this involves a high intake of water and considerable production of wastewater. This, in turn, necessi-tates the application of some technological solutions aimed at limiting the negative impact on the environment. The Jaworzno III Power Plant - Power Plant II is located in Jaworzno, Silesian Province, Poland. In order to minimise the negative impact on the surface water, the plant replenishes the cooling circuit with the mining water obtained from the closed-down Jan Kanty mine. The paper presents a stability assessment of the chemical composition of the treated mining water used to replenish the cooling circuit based on the data from 2007-2017.

Replenishing data descriptors in a DMA injection FIFO buffer

DOEpatents

Archer, Charles J [Rochester, MN; Blocksome, Michael A [Rochester, MN; Cernohous, Bob R [Rochester, MN; Heidelberger, Philip [Cortlandt Manor, NY; Kumar, Sameer [White Plains, NY; Parker, Jeffrey J [Rochester, MN

2011-10-11

Methods, apparatus, and products are disclosed for replenishing data descriptors in a Direct Memory Access (`DMA`) injection first-in-first-out (`FIFO`) buffer that include: determining, by a messaging module on an origin compute node, whether a number of data descriptors in a DMA injection FIFO buffer exceeds a predetermined threshold, each data descriptor specifying an application message for transmission to a target compute node; queuing, by the messaging module, a plurality of new data descriptors in a pending descriptor queue if the number of the data descriptors in the DMA injection FIFO buffer exceeds the predetermined threshold; establishing, by the messaging module, interrupt criteria that specify when to replenish the injection FIFO buffer with the plurality of new data descriptors in the pending descriptor queue; and injecting, by the messaging module, the plurality of new data descriptors into the injection FIFO buffer in dependence upon the interrupt criteria.

26 CFR 1.860F-1 - Qualified liquidations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 9 2011-04-01 2011-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan...

26 CFR 1.860F-1 - Qualified liquidations.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 9 2014-04-01 2014-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan...

26 CFR 1.860F-1 - Qualified liquidations.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 9 2012-04-01 2012-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan...

26 CFR 1.860F-1 - Qualified liquidations.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 9 2013-04-01 2013-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan...

RENEWABLE LIQUID GETTERING PUMP

DOEpatents

Batzer, T.H.

1962-08-21

A method and structure were developed for pumping gases by simple absorption into a liquid gettering material. The invention comprises means ror continuously pumping a liquid getterrng material from a reservoir to the top of a generally vertical surface disposed in a vacuum pumping chamber to receive gaseous and other particles in the liquid gettering material which continuously flows downward over the vertical suiface. Means are provided for continuous removal, degassing, and return of a portion of the liquid gettering material from the reservoir connected with collectrng means at the base of the generally vertical plate. (AEC)

Crewmembers in the middeck with the FARE experiment.

NASA Image and Video Library

1992-12-09

STS053-04-018 (2-9 Dec 1992) --- Astronauts Guion S. Bluford (left) and Michael R. U. (Rich) Clifford monitor the Fluid Acquisition and Resupply Equipment (FARE) onboard the Space Shuttle Discovery. Clearly visible in the mid-deck FARE setup is one of two 12.5-inch spherical tanks made of transparent acrylic, one to supply and one to receive fluids. The purpose of FARE is to investigate the dynamics of fluid transfer in microgravity and develop methods for transferring vapor-free propellants and other liquids that must be replenished in long-term space systems like satellites, Extended-Duration Orbiters (EDO), and Space Station Freedom. Eight times over an eight-hour test period, the mission specialists conducted the FARE experiment. A sequence of manual valve operations caused pressurized air from the bottles to force fluids from the supply tank to the receiver tank and back again to the supply tank. Baffles in the receiver tank controlled fluid motion during transfer, a fine-mesh screen filtered vapor from the fluid, and the overboard vent removed vapor from the receiver tank as the liquid rose. FARE is managed by NASA's Marshall Space Flight Center (MSFC) in Alabama. The basic equipment was developed by Martin Marietta for the Storable Fluid Management Demonstration. Susan L. Driscoll is the principal investigator.

Continuous electrophoretic purification of individual analytes from multicomponent mixtures.

PubMed

McLaren, David G; Chen, David D Y

2004-04-15

Individual analytes can be isolated from multicomponent mixtures and collected in the outlet vial by carrying out electrophoretic purification through a capillary column. Desired analytes are allowed to migrate continuously through the column under the electric field while undesired analytes are confined to the inlet vial by application of a hydrodynamic counter pressure. Using pressure ramping and buffer replenishment techniques, 18% of the total amount present in a bulk sample can be purified when the resolution to the adjacent peak is approximately 3. With a higher resolution, the yield could be further improved. Additionally, by periodically introducing fresh buffer into the sample, changes in pH and conductivity can be mediated, allowing higher purity (>or=99.5%) to be preserved in the collected fractions. With an additional reversed cycle of flow counterbalanced capillary electrophoresis, any individual component in a sample mixture can be purified providing it can be separated in an electrophoresis system.

Retailer's optimal credit period and cycle time in a supply chain for deteriorating items with up-stream and down-stream trade credits

NASA Astrophysics Data System (ADS)

Mahata, Gour Chandra

2015-09-01

In practice, the supplier often offers the retailers a trade credit period and the retailer in turn provides a trade credit period to her/his customer to stimulate sales and reduce inventory. From the retailer's perspective, granting trade credit not only increases sales and revenue but also increases opportunity cost (i.e., the capital opportunity loss during credit period) and default risk (i.e., the percentage that the customer will not be able to pay off his/her debt obligations). Hence, how to determine credit period is increasingly recognized as an important strategy to increase retailer's profitability. Also, the selling items such as fruits, fresh fishes, gasoline, photographic films, pharmaceuticals and volatile liquids deteriorate continuously due to evaporation, obsolescence and spoilage. In this paper, we propose an economic order quantity model for the retailer where (1) the supplier provides an up-stream trade credit and the retailer also offers a down-stream trade credit, (2) the retailer's down-stream trade credit to the buyer not only increases sales and revenue but also opportunity cost and default risk, and (3) the selling items are perishable. Under these conditions, we model the retailer's inventory system as a profit maximization problem to determine the retailer's optimal replenishment decisions under the supply chain management. We then show that the retailer's optimal credit period and cycle time not only exist but also are unique. We deduce some previously published results of other researchers as special cases. Finally, we use some numerical examples to illustrate the theoretical results.

Self-replenishing ability of cross-linked low surface energy polymer films investigated by a complementary experimental-simulation approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esteves, A. C. C., E-mail: a.c.c.esteves@tue.nl, E-mail: g.dewith@tue.nl; Lyakhova, K.; Riel, J. M. van

2014-03-28

Nowadays, many self-healing strategies are available for recovering mechanical damage of bulk polymeric materials. The recovery of surface-dependent functionalities on polymer films is, however, equally important and has been less investigated. In this work we study the ability of low surface energy cross-linked poly(ester urethane) networks containing perfluorinated dangling chains to self-replenish their surface, after being submitted to repeated surface damage. For this purpose we used a combined experimental-simulation approach. Experimentally, the cross-linked films were intentionally damaged by cryo-microtoming to remove top layers and create new surfaces which were characterized by water Contact Angle measurements and X-Ray Photoelectron Spectroscopy. Themore » same systems were simultaneously represented by a Dissipative Particles Dynamics simulation method, where the damage was modeled by removing the top film layers in the simulation box and replacing it by new “air” beads. The influence of different experimental parameters, such as the concentration of the low surface energy component and the molecular mobility span of the dangling chains, on the surface recovery is discussed. The combined approach reveals important details of the self-replenishing ability of damaged polymer films such as the occurrence of multiple-healing events, the self-replenishing efficiency, and the minimum “healing agent” concentration for a maximum recovery.« less

Quasi-continuous transition from a Fermi liquid to a spin liquid in κ-(ET)2Cu2(CN)3.

PubMed

Furukawa, Tetsuya; Kobashi, Kazuhiko; Kurosaki, Yosuke; Miyagawa, Kazuya; Kanoda, Kazushi

2018-01-22

The Mott metal-insulator transition-a manifestation of Coulomb interactions among electrons-is known as a discontinuous transition. Recent theoretical studies, however, suggest that the transition is continuous if the Mott insulator carries a spin liquid with a spinon Fermi surface. Here, we demonstrate the case of a quasi-continuous Mott transition from a Fermi liquid to a spin liquid in an organic triangular-lattice system κ-(ET) 2 Cu 2 (CN) 3 . Transport experiments performed under fine pressure tuning have found that as the Mott transition is approached, the Fermi liquid coherence temperature continuously falls to the scale of kelvins, with a divergent quasi-particle decay rate on the metal side, and the charge gap continuously closes on the insulator side. A Clausius-Clapeyron analysis provides thermodynamic evidence for the extremely weak first-order nature of the transition. These results provide additional support for the existence of a spinon Fermi surface, which becomes an electron Fermi surface when charges are delocalized.

Continuous-Reading Cryogen Level Sensor

NASA Technical Reports Server (NTRS)

Barone, F. E.; Fox, E.; Macumber, S.

1984-01-01

Two pressure transducers used in system for measuring amount of cryogenic liquid in tank. System provides continuous measurements accurate within 0.03 percent. Sensors determine pressure in liquid and vapor in tank. Microprocessor uses pressure difference to compute mass of cryogenic liquid in tank. New system allows continuous sensing; unaffected by localized variations in composition and density as are capacitance-sensing schemes.

Silicon Web Process Development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Hopkins, R. H.; Mchugh, J. P.; Hill, F. E.; Heimlich, M. E.; Driggers, J. M.

1978-01-01

Progress in the development of techniques to grow silicon web at 25 wq cm/min output rate is reported. Feasibility of web growth with simultaneous melt replenishment is discussed. Other factors covered include: (1) tests of aftertrimmers to improve web width; (2) evaluation of growth lid designs to raise speed and output rate; (3) tests of melt replenishment hardware; and (4) investigation of directed gas flow systems to control unwanted oxide deposition in the system and to improve convective cooling of the web. Compatibility with sufficient solar cell performance is emphasized.

A decision analysis approach to climate adaptation: comparing multiple pathways for multi-decadal decision making

NASA Astrophysics Data System (ADS)

Lin, B. B.; Little, L.

2013-12-01

Policy planners around the world are required to consider the implications of adapting to climatic change across spatial contexts and decadal timeframes. However, local level information for planning is often poorly defined, even though climate adaptation decision-making is made at this scale. This is especially true when considering sea level rise and coastal impacts of climate change. We present a simple approach using sea level rise simulations paired with adaptation scenarios to assess a range of adaptation options available to local councils dealing with issues of beach recession under present and future sea level rise and storm surge. Erosion and beach recession pose a large socioeconomic risk to coastal communities because of the loss of key coastal infrastructure. We examine the well-known adaptation technique of beach nourishment and assess various timings and amounts of beach nourishment at decadal time spans in relation to beach recession impacts. The objective was to identify an adaptation strategy that would allow for a low frequency of management interventions, the maintenance of beach width, and the ability to minimize variation in beach width over the 2010 to 2100 simulation period. 1000 replications of each adaptation option were produced against the 90 year simulation in order to model the ability each adaptation option to achieve the three key objectives. Three sets of adaptation scenarios were identified. Within each scenario, a number of adaptation options were tested. The three scenarios were: 1) Fixed periodic beach replenishment of specific amounts at 20 and 50 year intervals, 2) Beach replenishment to the initial beach width based on trigger levels of recession (5m, 10m, 20m), and 3) Fixed period beach replenishment of a variable amount at decadal intervals (every 10, 20, 30, 40, 50 years). For each adaptation option, we show the effectiveness of each beach replenishment scenario to maintain beach width and consider the implications of more frequent replenishment with that of implementation cost. We determine that a business as usual scenario, where no adaptation is implemented, would lead to an average beach recession of 12.02 meters and a maximum beach recession of 33.23 meters during the period of 2010-2100. The best adaptation option modeled was a fixed replenishment of 5 meters every 20 years leading to 4 replenishment events with an average beach recession of 2.99 meters and a maximum beach recession of 15.02 meters during the period of 2010-2100. The presented simulations explicitly address the uncertainty of future impacts due to sea level rise and storm surge and show a range of options that could be considered by a local council to meet their policy objectives. The simulation runs provide managers the ability to consider the utility of various adaptation options and the timing and costs of implementation. Such information provides an evidence-based practice to decision-making and allows policy makers to transparently make decisions based on best estimates of modeled climate change.

Wear reduction in ceramic bearings by surface generated pyrolytic carbon continuously replenished by ethylene gas

NASA Technical Reports Server (NTRS)

Lauer, J. L.; Davis, L. C.

1993-01-01

Sliding tests with a pin-on-disc tribometer and both sliding and rolling tests with a modified four-ball tester at bulk temperatures of about 500 C and contact pressures of about 2.2 GPa have demonstrated up to 80% reductions of friction and wear with silicon nitride surfaces when a stream of ethylene is directed into the conjunction region. The effects are even more pronounced when the ethylene is prenucleated by a flow over a coil of nichrome wire electrically heated to about 800 C and located about 30 cm upstream of the exit nozzle. Steel and Ni-plated steel are lubricated by this method even more efficiently at lower temperatures.

Ultrasound line-by-line scanning method of spatial-temporal active cavitation mapping for high-intensity focused ultrasound.

PubMed

Ding, Ting; Zhang, Siyuan; Fu, Quanyou; Xu, Zhian; Wan, Mingxi

2014-01-01

This paper presented an ultrasound line-by-line scanning method of spatial-temporal active cavitation mapping applicable in a liquid or liquid filled tissue cavities exposed by high-intensity focused ultrasound (HIFU). Scattered signals from cavitation bubbles were obtained in a scan line immediately after one HIFU exposure, and then there was a waiting time of 2 s long enough to make the liquid back to the original state. As this pattern extended, an image was built up by sequentially measuring a series of such lines. The acquisition of the beamformed radiofrequency (RF) signals for a scan line was synchronized with HIFU exposure. The duration of HIFU exposure, as well as the delay of the interrogating pulse relative to the moment while HIFU was turned off, could vary from microseconds to seconds. The feasibility of this method was demonstrated in tap-water and a tap-water filled cavity in the tissue-mimicking gelatin-agar phantom as capable of observing temporal evolutions of cavitation bubble cloud with temporal resolution of several microseconds, lateral and axial resolution of 0.50 mm and 0.29 mm respectively. The dissolution process of cavitation bubble cloud and spatial distribution affected by cavitation previously generated were also investigated. Although the application is limited by the requirement for a gassy fluid (e.g. tap water, etc.) that allows replenishment of nuclei between HIFU exposures, the technique may be a useful tool in spatial-temporal cavitation mapping for HIFU with high precision and resolution, providing a reference for clinical therapy. Copyright © 2013 Elsevier B.V. All rights reserved.

Relationship between starch and lipid accumulation induced by nutrient depletion and replenishment in the microalga Parachlorella kessleri.

PubMed

Fernandes, Bruno; Teixeira, José; Dragone, Giuliano; Vicente, António A; Kawano, Shigeyuki; Bišová, Kateřina; Přibyl, Pavel; Zachleder, Vilém; Vítová, Milada

2013-09-01

Photosynthetic carbon partitioning into starch and neutral lipids, as well as the influence of nutrient depletion and replenishment on growth, pigments and storage compounds, were studied in the microalga, Parachlorella kessleri. Starch was utilized as a primary carbon and energy storage compound, but nutrient depletion drove the microalgae to channel fixed carbon into lipids as secondary storage compounds. Nutrient depletion inhibited both cellular division and growth and caused degradation of chlorophyll. Starch content decreased from an initial value of 25, to around 10% of dry weight (DW), while storage lipids increased from almost 0 to about 29% of DW. After transfer of cells into replenished mineral medium, growth, reproductive processes and chlorophyll content recovered within 2 days, while the content of both starch and lipids decreased markedly to 3 or less % of DW; this suggested that they were being used as a source of energy and carbon. Copyright © 2013 Elsevier Ltd. All rights reserved.

A hybrid of monopoly and perfect competition model for hi-tech products

NASA Astrophysics Data System (ADS)

Yang, P. C.; Wee, H. M.; Pai, S.; Yang, H. J.; Wee, P. K. P.

2010-11-01

For Hi-tech products, the demand rate, the component cost as well as the selling price usually decline significantly with time. In the case of perfect competition, shortages usually result in lost sales; while in a monopoly, shortages will be completely backordered. However, neither perfect competition nor monopoly exists. Therefore, there is a need to develop a replenishment model considering a hybrid of perfect competition and monopoly when the cost, price and demand are decreasing simultaneously. A numerical example and sensitivity analysis are carried out to illustrate this model. The results show that a higher decline-rate in the component cost leads to a smaller service level and a larger replenishment interval. When the component cost decline rate increases and the selling price decline rate decreases simultaneously, the replenishment interval decreases. In perfect competition it is better to have a high service level, while for the case with monopoly, keeping a low service level is better due to complete backordering.

Liquid-liquid phase transformations and the shape of the melting curve.

PubMed

Makov, G; Yahel, E

2011-05-28

The phase diagram of elemental liquids has been found to be surprisingly rich, including variations in the melting curve and transitions in the liquid phase. The effect of these transitions in the liquid state on the shape of the melting curve is analyzed. First-order phase transitions intersecting the melting curve imply piecewise continuous melting curves, with solid-solid transitions generating upward kinks or minima and liquid-liquid transitions generating downward kinks or maxima. For liquid-liquid phase transitions proposed for carbon, phosphorous selenium, and possibly nitrogen, we find that the melting curve exhibits a kink. Continuous transitions imply smooth extrema in the melting curve, the curvature of which is described by an exact thermodynamic relation. This expression indicates that a minimum in the melting curve requires the solid compressibility to be greater than that of the liquid, a very unusual situation. This relation is employed to predict the loci of smooth maxima at negative pressures for liquids with anomalous melting curves. The relation between the location of the melting curve maximum and the two-state model of continuous liquid-liquid transitions is discussed and illustrated by the case of tellurium. © 2011 American Institute of Physics

Long-term environmental impacts of building composites containing waste materials: Evaluation of the leaching protocols.

PubMed

Drinčić, Ana; Nikolić, Irena; Zuliani, Tea; Milačič, Radmila; Ščančar, Janez

2017-01-01

The NEN 7375 test has been proposed for evaluating the long-term environmental impacts caused by the release of contaminants from monolithic building and waste materials. Over a period of 64days, at specific points in time, the leaching solution (demineralised water) is replenished. By applying the NEN 7375 test, leaching of contaminants that is based mainly on diffusion is followed. In the present work, the results from modified leaching protocols were evaluated against those obtained by NEN 7375 test. In modified protocols, synthetic sea, surface and MilliQ water were used for the leaching of selected elements and chromate, molybdate and vanadate from compact and ground building composites (98% mixture of fly ash (80%) and cement (20%), and 2% of electric arc furnace (EAF) dust) over 6months. The leaching solutions were not replenished, imitating both the diffusion and the dissolution of contaminants. The data revealed larger extent of leaching when the leaching solution was not replenished. More extensive was also leaching from ground composites, which simulated the disintegration of the material over time. The composition of the leaching solution influenced the release of the matrix constituents from the composites and, consequently, the amount of elements and their chemical species. Synthetic sea and surface water used as leaching solutions, without replenishing, were found to be suitable to simulate the conditions when the building material is immersed in stagnant environmental waters. Copyright © 2016 Elsevier Ltd. All rights reserved.

Predaceous ants, beach replenishment, and nest placement by sea turtles.

PubMed

Wetterer, James K; Wood, Lawrence D; Johnson, Chris; Krahe, Holly; Fitchett, Stephanie

2007-10-01

Ants known for attacking and killing hatchling birds and reptiles include the red imported fire ant (Solenopsis invicta Buren), tropical fire ant [Solenopsis geminata (Fabr.)], and little fire ant [Wasmannia auropunctata (Roger)]. We tested whether sea turtle nest placement influenced exposure to predaceous ants. In 2000 and 2001, we surveyed ants along a Florida beach where green turtles (Chelonia mydas L.), leatherbacks (Dermochelys coriacea Vandelli), and loggerheads (Caretta caretta L.) nest. Part of the beach was artificially replenished between our two surveys. As a result, mean beach width experienced by nesting turtles differed greatly between the two nesting seasons. We surveyed 1,548 sea turtle nests (2000: 909 nests; 2001: 639 nests) and found 22 ant species. S. invicta was by far the most common species (on 431 nests); S. geminata and W. auropunctata were uncommon (on 3 and 16 nests, respectively). In 2000, 62.5% of nests had ants present (35.9% with S. invicta), but in 2001, only 30.5% of the nests had ants present (16.4% with S. invicta). Turtle nests closer to dune vegetation had significantly greater exposure to ants. Differences in ant presence on turtle nests between years and among turtle species were closely related to differences in nest placement relative to dune vegetation. Beach replenishment significantly lowered exposure of nests to ants because on the wider beaches turtles nested farther from the dune vegetation. Selective pressures on nesting sea turtles are altered both by the presence of predaceous ants and the practice of beach replenishment.

40 CFR 761.340 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... leaching characteristics for storage or disposal. (a) Existing accumulations of non-liquid, non-metal PCB bulk product waste. (b) Non-liquid, non-metal PCB bulk product waste from processes that continuously generate new waste. (c) Non-liquid PCB remediation waste from processes that continuously generate new...

A Droplet Microfluidic Platform for Automating Genetic Engineering.

PubMed

Gach, Philip C; Shih, Steve C C; Sustarich, Jess; Keasling, Jay D; Hillson, Nathan J; Adams, Paul D; Singh, Anup K

2016-05-20

We present a water-in-oil droplet microfluidic platform for transformation, culture and expression of recombinant proteins in multiple host organisms including bacteria, yeast and fungi. The platform consists of a hybrid digital microfluidic/channel-based droplet chip with integrated temperature control to allow complete automation and integration of plasmid addition, heat-shock transformation, addition of selection medium, culture, and protein expression. The microfluidic format permitted significant reduction in consumption (100-fold) of expensive reagents such as DNA and enzymes compared to the benchtop method. The chip contains a channel to continuously replenish oil to the culture chamber to provide a fresh supply of oxygen to the cells for long-term (∼5 days) cell culture. The flow channel also replenished oil lost to evaporation and increased the number of droplets that could be processed and cultured. The platform was validated by transforming several plasmids into Escherichia coli including plasmids containing genes for fluorescent proteins GFP, BFP and RFP; plasmids with selectable markers for ampicillin or kanamycin resistance; and a Golden Gate DNA assembly reaction. We also demonstrate the applicability of this platform for transformation in widely used eukaryotic organisms such as Saccharomyces cerevisiae and Aspergillus niger. Duration and temperatures of the microfluidic heat-shock procedures were optimized to yield transformation efficiencies comparable to those obtained by benchtop methods with a throughput up to 6 droplets/min. The proposed platform offers potential for automation of molecular biology experiments significantly reducing cost, time and variability while improving throughput.

Halting Land Subsidence in Tucson, Arizona: Examining the Poroelastic Response to Artificial Recharge

NASA Astrophysics Data System (ADS)

Miller, M. M.; Shirzaei, M.; Argus, D. F.

2017-12-01

Overexploitation of groundwater results in stressed aquifer systems and surface deformation in the form of land subsidence. Differential land subsidence can lead to earth fissures, which threaten buildings and infrastructure. Therefore, careful water management is necessary to ensure aquifer resources are withdrawn and replenished at a sustainable yield to preserve supplies and minimize surface deformation. Tucson, Arizona is a semi-arid desert city that is reliant on a semi-confined alluvial aquifer system for much of the water supply. To understand the poroelastic response of the aquifer system over time, we analyze data from wells equipped with extensometers, InSAR time series, and GPS. From 1990-2005, compaction of fine-grained, aquitard material is measured up to 8.5 mm/yr at well sites equipped with extensometers. This induces permanent aquifer storage volume losses up to 4.1%. Yet, interferograms from Envisat and RadarSAT-2 C-band satellites, which yield multitemporal deformation maps at high resolution, reveal that subsidence remarkably slows by the late 2000s and nearly halts by 2015. We infer this deceleration corresponds to heightened artificial recharge efforts to bank Colorado River water delivered via canal. After groundwater levels recover, residual compaction continues for just a 6.6-year interval, which suggests a high value for vertical hydraulic conductivity up to 9.8 x10-4 m/day. Successful water management and conservation plans help the city preserve existing and replenish depleted groundwater reserves, decelerate land subsidence, and likely reduce the risks associated with earth fissuring.

Electron radiation belt dynamics during magnetic storms and in quiet time

NASA Astrophysics Data System (ADS)

Lazutin, Leonid; Dmitriev, Aleksey; Suvorova, Alla

2018-03-01

The paper discusses the dynamics of the outer electron belt, adiabatic and nonadiabatic mechanisms of replenishment and losses of energetic electrons. Under undisturbed conditions, the outer electron belt gradually empties: in the inner magnetosphere due to electron precipitation in the atmosphere and in the quasi-trapping region due to losses at the magnetopause because drift shells of electrons are not closed there. The latter process does not occur in normal years due to the masking replenishment by freshly accelerated particles, but in years of extremely low activity, it leads to a significant decrease in the electron population of the belt. During the magnetic storm main phase, the first reason for the decrease in the electron flux intensity is the adiabatic cooling associated with conservation of adiabatic invariants and complemented by precipitation of electrons into the atmosphere and their dropout at the magnetopause. Electron flux increases involve E×B electron injection by the induction electric field of substorm activation and by the large-scale solar wind electric field, with pitch energy diffusion along with adiabatic heating in the recovery phase. The rate of electron flux recovery after a storm is determined by the ratio of nonadiabatic increases and losses; hence the electron flux represents a continuous series from low to very high values. The combination of these processes determines the individual character of radiation belt development during each magnetic storm and the behavior of the belt in the quiet time.

Sequential continuous flow processes for the oxidation of amines and azides by using HOF·MeCN.

PubMed

McPake, Christopher B; Murray, Christopher B; Sandford, Graham

2012-02-13

The generation and use of the highly potent oxidising agent HOF·MeCN in a controlled single continuous flow process is described. Oxidations of amines and azides to corresponding nitrated systems by using fluorine gas, water and acetonitrile by sequential gas-liquid/liquid-liquid continuous flow procedures are reported. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of meteorite impacts on the atmospheric evolution of Mars.

PubMed

Pham, Lê Binh San; Karatekin, Ozgür; Dehant, Véronique

2009-01-01

Early in its history, Mars probably had a denser atmosphere with sufficient greenhouse gases to sustain the presence of stable liquid water at the surface. Impacts by asteroids and comets would have played a significant role in the evolution of the martian atmosphere, not only by causing atmospheric erosion but also by delivering material and volatiles to the planet. We investigate the atmospheric loss and the delivery of volatiles with an analytical model that takes into account the impact simulation results and the flux of impactors given in the literature. The atmospheric loss and the delivery of volatiles are calculated to obtain the atmospheric pressure evolution. Our results suggest that the impacts alone cannot satisfactorily explain the loss of significant atmospheric mass since the Late Noachian (approximately 3.7-4 Ga). A period with intense bombardment of meteorites could have increased the atmospheric loss; but to explain the loss of a speculative massive atmosphere in the Late Noachian, other factors of atmospheric erosion and replenishment also need to be taken into account.

Superoleophobic yet Superhydrophilic surfaces for Continuous Liquid-Liquid Separation

DTIC Science & Technology

2011-12-08

cases, such membranes are oleophilic, i.e., Young’s contact angle (12) with oil !oil < 90º. Hydrophobic (or superhydrophobic (10, 11, 13)) and...continuous liquid-liquid separation. Final Report, Anish Tuteja, University of Michigan 3 hydrophobic (or superhydrophobic ) membranes are easily...in air typically loses its oleophobicity under water and vice-versa (17, 18). Despite numerous natural superhydrophobic surfaces (19, 20), due to

Quantifying anthropogenically driven morphologic changes on a barrier island: Fire Island National Seashore, New York

USGS Publications Warehouse

Kratzmann, Meredith G.; Hapke, Cheryl J.

2012-01-01

Beach scraping, beach replenishment, and the presence of moderate development have altered the morphology of the dune–beach system at Fire Island National Seashore, located on a barrier island on the south coast of Long Island, New York. Seventeen communities are interspersed with sections of natural, nonmodified land within the park boundary. Beach width, dune elevation change, volume change, and shoreline change were calculated from light detection and ranging (LIDAR), real-time kinematic global positioning system (RTK GPS), and beach profile data sets at two ∼4 km long study sites. Each site contains both modified (developed, replenished, and/or scraped) and nonmodified (natural) areas. The analysis spans 9 years, from 1998 to 2007, which encompasses both scraping and replenishment events at Fire Island. The objectives of this study were to quantify and compare morphological changes in modified and nonmodified zones, and to identify erosional areas within the study sites.Areas of increased volume and shoreline accretion were observed at both sites and at the western site are consistent with sand replenishment activities. The results indicate that from 1998 to 2007 locations backed by development and that employed beach scraping and/or replenishment as erosion control measures experienced more loss of volume, width, and dune elevation as compared with adjacent nonmodified areas. A detailed analysis of one specific modification, beach scraping, shows distinct morphological differences in scraped areas relative to nonscraped areas of the beach. In general, scraped areas where there is development on the dunes showed decreases in all measured parameters and are more likely to experience overwash during storm events. Furthermore, the rapid mobilization of material from the anthropogenic (scraped) dune results in increased beach accretion downcoast.National park lands are immediately adjacent to developed areas on Fire Island, and even relatively small human-induced modifications can affect park resources and beach–dune response to storms. This study is the first to conduct a systematic analysis on how anthropogenic modifications affect resources at Fire Island National Seashore and provides essential information for effective management and preservation of coastal resources within the park.

Nutrient management effects on sweetpotato genotypes under controlled environment

NASA Technical Reports Server (NTRS)

David, P. P.; Bonsi, C. K.; Trotman, A. A.; Douglas, D. Z.

1996-01-01

Sweetpotato is one of several crops recommended by National Aeronautics and Space Administration (NASA) for bioregenerative life support studies. One of the objectives of the Tuskegee University NASA Center is to optimize growth conditions for adaptability of sweetpotatoes for closed bioregenerative systems. The role of nutrient solution management as it impacts yield has been one of the major thrusts in these studies. Nutrient solution management protocol currently used consists of a modified half Hoagland solution that is changed at 14-day intervals. Reservoirs are refilled with deionized water if the volume of the nutrient solution was reduced to 8 liters or less before the time of solution change. There is the need to recycle and replenish nutrient solution during crop growth, rather than discard at 14 day intervals as previously done, in order to reduce waste. Experiments were conducted in an environmental growth room to examine the effects of container size on the growth of several sweetpotato genotypes grown under a nutrient replenishment protocol. Plants were grown from vine cuttings of 15cm length and were planted in 0.15 x 0.15 x 1.2m growth channels using a closed nutrient film technique system. Nutrient was supplied in a modified half strength Hoagland's solution with a 1:2.4 N:K ratio. Nutrient replenishment protocol consisted of daily water replenishment to a constant volume of 30.4 liters in the small containers and 273.6 liters in the large container. Nutrients were replenished as needed when the EC of the nutrient solution fell below 1200 mhos/cm. The experimental design used was a split-plot with the main plot being container size and genotypes as the subplot. Nine sweetpotato genotypes were evaluated. Results showed no effect of nutrient solution container size on storage root yield, foliage fresh and dry mass, leaf area or vine length. However, plants grown using the large nutrient solution container accumulated more storage root dry mass than those with the small containers. Although plants grown with the smaller containers showed greater water uptake, plant nutrient uptake was lower than with the larger container. All genotypes evaluated showed variation in their responses to all parameters measured.

26 CFR 1.860F-1 - Qualified liquidations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan of...

Experience and prospects of oil shale utilization for power production in Russia

NASA Astrophysics Data System (ADS)

Potapov, O. P.

2016-09-01

Due to termination of work at the Leningrad Shale Deposit, the Russian shale industry has been liquidated, including not only shale mining and processing but also research and engineering (including design) activities, because this deposit was the only commercially operated complex in Russia. UTT-3000 plants with solid heat carrier, created mainly by the Russian specialists under scientific guidance of members of Krzhizhanovsky Power Engineering Institute, passed under the control of Estonian engineers, who, alongside with their operation in Narva, construct similar plants in Kohtla-Jarve, having renamed the Galoter Process into the Enifit or Petroter. The main idea of this article is to substantiate the expediency of revival of the oil shale industry in Russia. Data on the UTT-3000 plants' advantages, shale oils, and gas properties is provided. Information on investments in an UTT-3000 plant and estimated cost of Leningrad oil shale mining at the Mezhdurechensk Strip Mine is given. For more detailed technical and economic assessment of construction of a complex for oil shale extraction and processing, it is necessary to develop a feasibility study, which should be the first stage of this work. Creation of such a complex will make it possible to produce liquid and gaseous power fuel from oil shale of Leningrad Deposit and provide the opportunity to direct for export the released volumes of oil and gas for the purposes of Russian budget currency replenishment.

Perfluoropolyether-Impregnated Mesoporous Alumina Composites Overcome the Dewetting-Tribological Properties Trade-Off.

PubMed

Rowthu, Sriharitha; Hoffmann, Patrik

2018-03-28

Conventional omniphobic surfaces suffer from wear-sensitivity due to soft apolar coatings or substrates and protruding surface features that are eroded even for mild abrasion treatments, leading to the loss of dewetting properties after wear. Evidently, there was a trade-off between dewetting and tribological properties. Here, we show the establishment of self-healing slippery properties post severe abrasion by utilizing perfluoropolyether-impregnated mesoporous Al 2 O 3 (MPA) composites. The hard polar alumina matrix provides the optimal tribological properties, and the liquid lubricant in the porous network contributes to both tribological and self-healing dewetting properties. These composites sustained normal pressures up to 350 MPa during reciprocating sliding contacts. The severely abraded surfaces are capable of self-replenishing in ambient environment, driven by capillarity and surface diffusion processes, and regained their slippery properties toward water and hexadecane after 15 h of self-healing. Eventually, a dewetting-tribology diagram has been introduced to show different regimes, namely-optimal slippery properties, optimal tribological properties, and a mixed regime). We found out that the microstructural expression [Formula: see text] is a robust guiding tool to predict the regime of interest. This dewetting-tribological diagram may be marked as an inception to designing abrasion-resistant slippery liquid impregnated composites for overcoming the dewetting tribological properties trade-off. Such surfaces may potentially find applications in paint industries and as anti-icing surfaces.

Detail view of the Fluid Acquisition and Resupply Equipment experiment.

NASA Image and Video Library

1992-12-09

STS053-09-019 (2 - 9 Dec 1992) --- A medium close-up view of part of the Fluid Acquisition and Resupply Equipment (FARE) onboard the Space Shuttle Discovery. Featured in the mid-deck FARE setup is fluid activity in one of two 12.5-inch spherical tanks made of transparent acrylic. Pictured is the receiver tank. The other tank, out of frame below, is for supplying fluids. The purpose of FARE is to investigate the dynamics of fluid transfer in microgravity and develop methods for transferring vapor-free propellants and other liquids that must be replenished in long-term space systems like satellites, Extended-Duration Orbiters (EDO), and Space Station Freedom. Eight times over an eight-hour test period, the mission specialists conducted the FARE experiment. A sequence of manual valve operations caused pressurized air from the bottles to force fluids from the supply tank to the receiver tank and back again to the supply tank. Baffles in the receiver tank controlled fluid motion during transfer, a fine-mesh screen filtered vapor from the fluid, and the overboard vent removed vapor from the receiver tank as the liquid rose. FARE is managed by NASA's Marshall Space Flight Center (MSFC) in Alabama. The basic equipment was developed by Martin Marietta for the Storable Fluid Management Demonstration. Susan L. Driscoll is the principal investigator.

Effect of diet on the replenishment of intramyocellular lipids after exercise.

PubMed

Décombaz, J; Fleith, M; Hoppeler, H; Kreis, R; Boesch, C

2000-12-01

Muscle triglycerides are important as a source of energy and in relation to metabolic sensitivity. However, the classic biopsy method does not distinguish intra- from extracellular fat, and their regulation by exercise and diet is largely unknown. Magnetic resonance spectroscopy (MRS) is available to assess the intramyocellular lipid (IMCL) pool non-invasively in humans. The aim of this work was to use sequential MRS measurements of IMCL and glycogen to explore the role of three levels of dietary fat on the replenishment of these energy stores after exercise. Following 2 h of exercise, two subjects (S1, S2) were fed one of three diets (15%, 40% or 70% fat energy), each on a separate occasion. IMCL and glycogen were measured by MRS in the tibialis anterior muscle before, after exercise, and at 10 and at 32 h of recovery. Initial IMCL concentration (mmol.kg-1: 3.0 in S1 and 1.8 in S2) was reduced to 70% after exercise. The rate of replenishment was minimal with the low-fat (mmol.kg-1.24 h-1: 0.7 and 0.0) and much higher with both higher fat diets (mmol.kg-1.24 h-1: 3.1 and 3.2 in S1, 0.7 and 0.9 in S2). Glycogen and IMCL replenishments were inversely correlated. IMCL and glycogen can vary acutely in response to diet after exercise. Studies are needed to determine if such variations occur within the range of ordinary diets and to clarify the functional significance of IMCL in differently active individuals.

Development of an Intermediate-Scale Aerobic Bioreactor to Regenerate Nutrients from Inedible Crop Residues

NASA Technical Reports Server (NTRS)

Finger, Barry W.; Strayer, Richard F.

1994-01-01

Three Intermediate-Scale Aerobic Bioreactors were designed, fabricated, and operated. They utilized mixed microbial communities to bio-degrade plant residues. The continuously stirred tank reactors operated at a working volume of 8 L, and the average oxygen mass transfer coefficient, k(sub L)a, was 0.01 s(exp -1). Mixing time was 35 s. An experiment using inedible wheat residues, a replenishment rate of 0.125/day, and a solids loading rate of 20 gdw/day yielded a 48% reduction in biomass. Bioreactor effluent was successfully used to regenerate a wheat hydroponic nutrient solution. Over 80% of available potassium, calcium, and other minerals were recovered and recycled in the 76-day wheat growth experiment.

Finding the key - cell biology and science education.

PubMed

Miller, Kenneth R

2010-12-01

No international research community, cell biology included, can exist without an educational community to renew and replenish it. Unfortunately, cell biology researchers frequently regard their work as independent of the process of education and see little reason to reach out to science teachers. For cell biology to continue to prosper, I argue that researchers must support education in at least three ways. First, we must view education and research as part of a single scientific community. Second, we should take advantage of new technologies to connect the research laboratory to the classroom. Finally, we must take the initiative in defending the integrity of science teaching, particularly when education is under attack for political or religious reasons. Copyright © 2010 Elsevier Ltd. All rights reserved.

Chasing quicksilver: modeling the atmospheric lifetime of Hg(0)(g) in the marine boundary layer at various latitudes.

PubMed

Hedgecock, Ian M; Pirrone, Nicola

2004-01-01

The lifetime of elemental mercury in the marine boundary layer(MBL) has been studied using AMCOTS (Atmospheric Mercury Chemistry Over The Sea), a box model of MBL photochemistry including aerosols and detailed mercury chemistry. Recently measured Hg(0)(g) oxidation reactions have been included, and the studies were performed as a function of latitude, time of year, boundary layer liquid water content (LWC) and cloud optical depth. The results show that Hg has the shortest lifetime when air temperatures are low and sunlight and deliquescent aerosol particles are plentiful. Thus the modeled lifetime for clear-sky conditions is actually shorter at mid-latitudes and high latitudes than near the equator, and for a given latitude and time of year, cooler temperatures enhance the rate of Hg oxidation. Under typical summer conditions (for a given latitude) of temperature and cloudiness, the lifetime (tau) of Hg(0)(g) in the MBL is calculated to be around 10 days at all latitudes between the equator and 60 degrees N. This is much shorter than the generally accepted atmospheric residence time for Hg(0)(g) of a year or more. Given the relatively stable background concentrations of Hg(0)(g) which have been measured, continual replenishment of Hg(0)(g) must take place, suggesting a "multihop" mechanism for the distribution of Hg, rather than solely aeolian transport with little or no chemical transformation between source and receptor. Inclusion of an empirical Hg(0)(g) emission factor related to insolation was used to stabilize the Hg(0)(g) concentration in the model, and the emission rates necessarily agree well with estimated emission fluxes for the open ocean.

Bassoon-disruption slows vesicle replenishment and induces homeostatic plasticity at a CNS synapse

PubMed Central

Mendoza Schulz, Alejandro; Jing, Zhizi; María Sánchez Caro, Juan; Wetzel, Friederike; Dresbach, Thomas; Strenzke, Nicola; Wichmann, Carolin; Moser, Tobias

2014-01-01

Endbulb of Held terminals of auditory nerve fibers (ANF) transmit auditory information at hundreds per second to bushy cells (BCs) in the anteroventral cochlear nucleus (AVCN). Here, we studied the structure and function of endbulb synapses in mice that lack the presynaptic scaffold bassoon and exhibit reduced ANF input into the AVCN. Endbulb terminals and active zones were normal in number and vesicle complement. Postsynaptic densities, quantal size and vesicular release probability were increased while vesicle replenishment and the standing pool of readily releasable vesicles were reduced. These opposing effects canceled each other out for the first evoked EPSC, which showed unaltered amplitude. We propose that ANF activity deprivation drives homeostatic plasticity in the AVCN involving synaptic upscaling and increased intrinsic BC excitability. In vivo recordings from individual mutant BCs demonstrated a slightly improved response at sound onset compared to ANF, likely reflecting the combined effects of ANF convergence and homeostatic plasticity. Further, we conclude that bassoon promotes vesicular replenishment and, consequently, a large standing pool of readily releasable synaptic vesicles at the endbulb synapse. PMID:24442636

Ethane's 12C/13C Ratio in Titan: Implications for Methane Replenishment

NASA Technical Reports Server (NTRS)

Jennings, Donald E.; Nixon, C. A.; Romani, P. N.; Bjoraker, G. L.; Sada, P. V.; Lunsford, A. W.; Boyle, R. J.; Hesman, B. E.; McCabe, G. H.

2009-01-01

As the .main destination of carbon in the destruction of methane in the atmosphere of Titan, ethane provides information about the carbon isotopic composition of the reservoir from which methane is replenished. If the amount of methane entering the atmosphere is presently equal to the amount converted to ethane, the 12C/13C ratio in ethane should be close to the ratio in the reservoir. We have measured the 12C/13C ratio in ethane both with Cassini CIRS(exp 1) and from the ground and find that it is very close to the telluric standard and outer planet values (89), consistent with a primordial origin for the methane reservoir. The lower 12C/13C ratio measured for methane by Huygens GCMS (82.3) can be explained if the conversion of CH4 to CH3 (and C2H6) favors 12C over 13C with a carbon kinetic isotope effect of 1.08. The time required for the atmospheric methane to reach equilibrium, i.e., for replenishment to equal destruction, is approximately 5 methane atmospheric lifetimes.

Maintaining stable radiation pressure acceleration of ion beams via cascaded electron replenishment

NASA Astrophysics Data System (ADS)

Shen, X. F.; Qiao, B.; Chang, H. X.; Zhang, W. L.; Zhang, H.; Zhou, C. T.; He, X. T.

2017-03-01

A method to maintain ion stable radiation pressure acceleration (RPA) from laser-irradiated thin foils is proposed, where a series of high-Z nanofilms are placed behind to successively replenish co-moving electrons into the accelerating foil as electron charging stations (ECSs). Such replenishment of co-moving electrons, on the one hand, helps to keep a dynamic balance between the electrostatic pressure in the accelerating slab and the increasing laser radiation pressure with a Gaussian temporal profile at the rising front, i.e. dynamically matching the optimal condition of RPA; on the other hand, it aids in suppressing the foil Coulomb explosion due to loss of electrons induced by transverse instabilities during RPA. Two-dimensional and three-dimensional particle-in-cell simulations show that a monoenergetic Si14+ beam with a peak energy of 3.7 GeV and particle number 4.8× {10}9 (charge 11 nC) can be obtained at an intensity of 7 × 1021 W cm-2 and the conversion efficiency from laser to high energy ions is improved significantly by using the ECSs in our scheme.

Large Area Silicon Sheet by EFG. [quality control and productivity of edge-defined film-fed growth of ribbons

NASA Technical Reports Server (NTRS)

1979-01-01

Influences on ribbon quality which might be caused by various materials of construction which are used in the growth furnace were assessed. At the present level of ribbon quality, which has produced 8.5% to 9.5% efficient solar cells, no particular influence of any furnace part was detected. The experiments led to the suspicion that the general environment and the somewhat unoptimized materials handling procedures might be responsible for the current variations in ribbon quality and that, therefore, continuous work with this furnace under rather more stringent environmental conditions and operating procedures could perhaps improve materials quality to some extent. The work on the multiple furnace was continued with two multiple growth runs being performed. In these runs, the melt replenishment system performed poorly and extensive modifications to it were designed to make reliable melt feeding for five ribbon growth possible. Additional characterization techniques for wide ribbons, stress measurements, and growth dynamics experiments are reported.

On-Orbit Propulsion System Performance of ISS Visiting Vehicles

NASA Technical Reports Server (NTRS)

Martin, Mary Regina M.; Swanson, Robert A.; Kamath, Ulhas P.; Hernandez, Francisco J.; Spencer, Victor

2013-01-01

The International Space Station (ISS) represents the culmination of over two decades of unprecedented global human endeavors to conceive, design, build and operate a research laboratory in space. Uninterrupted human presence in space since the inception of the ISS has been made possible by an international fleet of space vehicles facilitating crew rotation, delivery of science experiments and replenishment of propellants and supplies. On-orbit propulsion systems on both ISS and Visiting Vehicles are essential to the continuous operation of the ISS. This paper compares the ISS visiting vehicle propulsion systems by providing an overview of key design drivers, operational considerations and performance characteristics. Despite their differences in design, functionality, and purpose, all visiting vehicles must adhere to a common set of interface requirements along with safety and operational requirements. This paper addresses a wide variety of methods for satisfying these requirements and mitigating credible hazards anticipated during the on-orbit life of propulsion systems, as well as the seamless integration necessary for the continued operation of the ISS.

Possible Niches for Extant Life on Titan in Light of Cassini/Huygens Results

NASA Astrophysics Data System (ADS)

Grinspoon, D. H.; Bullock, M. A.; Spencer, J. R.; Schulze-Makuch, D.

2005-08-01

Results from the first year of the Cassini mission show that Titan has an active surface with few impact craters and abundant hints of cryovolcanism, tectonism, aeolian and fluvial activity (Porco et al., 2005; Elachi et al., 2005). Methane clouds and surface characteristics strongly imply the presence of an active global methane cycle analogous to Earth's hydrological cycle. Astrobiological interest in Titan has previously focused on possible prebiological chemical evolution on a moon with a thick nitrogen atmosphere and rich organic chemistry (Raulin and Owen, 2002). Yet the emerging new picture of Titan has raised prospects for the possibility of extant life. Several key requirements for life appear to be present, including liquid reservoirs, organic molecules and ample energy sources. One promising location may be hot springs in contact with hydrocarbon reservoirs. Hydrogenation of photochemically produced acetylene could provide metabolic energy for near-surface organisms and also replenish atmospheric methane (Schulze-Makuch and Grinspoon, 2005). The energy released could be used by organisms to drive endothermic reactions, or go into heating their surroundings, helping to create their own liquid microenvironments. In environments which are energy-rich but liquid-poor, like the near-surface of Titan, natural selection may favor organisms that use their ``waste heat" to melt their own watering holes. Downward transport of high energy photochemical compounds could provide an energy supply for near-surface organisms which could be used, in part, to maintain the liquid environments conducive to life. We will present the results of thermal modeling designed to test the feasibility of biothermal melting on Titan. C. Porco and the Cassini Imaging Team (2005) Nature 434, 159-168; C. Elachi et al, Science, 308, 970-974; F. Raulin and T. Owen (2002) Space Sci. Rev. 104, 377 - 394.; D. Schulze-Makuch and D. H. Grinspoon (2005) Astrobiology, in press.

Composite Materials for Maxillofacial Prostheses.

DTIC Science & Technology

1980-08-01

projected composite systems are elastomeric-shelled, liquid-filled * microcapsules . Experiments continued on the interfacial polymerization process with...filled microcapsules . Experiments continued on the interfacial polymerization process, with spherical, sealed, capsules achieved. Needs identified are...consists of liquid-filled, elastomeric-shelled microcapsules held together to form a deformable mass; this is to simulate the semi-liquid cellular structure

The optimal inventory policy for EPQ model under trade credit

NASA Astrophysics Data System (ADS)

Chung, Kun-Jen

2010-09-01

Huang and Huang [(2008), 'Optimal Inventory Replenishment Policy for the EPQ Model Under Trade Credit without Derivatives International Journal of Systems Science, 39, 539-546] use the algebraic method to determine the optimal inventory replenishment policy for the retailer in the extended model under trade credit. However, the algebraic method has its limit of application such that validities of proofs of Theorems 1-4 in Huang and Huang (2008) are questionable. The main purpose of this article is not only to indicate shortcomings but also to present the accurate proofs for Huang and Huang (2008).

Apparatus for growing a dendritic web

DOEpatents

Duncan, Charles S.; Piotrowski, Paul A.; Skutch, Maria E.; McHugh, James P.

1983-06-21

A melt system including a susceptor-crucible assembly having improved gradient control when melt replenishment is used during dendritic web growth. The improvement lies in the formation of a thermal barrier in the base of the receptor which is in the form of a vertical slot in the region of the susceptor underlying the crucible at the location of a compartmental separator dividing the crucible into a growth compartment and a melt replenishment compartment. The result achieved is a step change in temperature gradient in the melt thereby providing a more uniform temperature in the growth compartment from which the dendritic web is drawn.

A unified convergence theory of a numerical method, and applications to the replenishment policies.

PubMed

Mi, Xiang-jiang; Wang, Xing-hua

2004-01-01

In determining the replenishment policy for an inventory system, some researchers advocated that the iterative method of Newton could be applied to the derivative of the total cost function in order to get the optimal solution. But this approach requires calculation of the second derivative of the function. Avoiding this complex computation we use another iterative method presented by the second author. One of the goals of this paper is to present a unified convergence theory of this method. Then we give a numerical example to show the application of our theory.

A feasibility study of methods for stopping the depletion of ozone over Antarctica

NASA Technical Reports Server (NTRS)

1988-01-01

Ways of stopping the ozone depletion in the ozone hole over Antarctica were studied. The basic objectives were: (1) to define and understand the phenomenon of the ozone hole; (2) to determine possible methods of stopping the ozone depletion; (3) to identify unknowns about the hole and possible solutions. Two basic ways of attacking the problem were identified. First is replenishment of ozone as it is being depleted. Second is elimination of ozone destroying agents from the atmosphere. The second method is a more permanent form of the solution. Elimination and replenishment methods are discussed in detail.

Energy spectrum and kinetics of the fusing particles

NASA Astrophysics Data System (ADS)

Ryutov, D. D.; Putvinski, s. V.; Yushmanov, P. N.; TAE Team

2017-10-01

The fusing particles (e.g., D and T, or p and 11B) contribution to the reaction rate can be found by the integration of the fusion reactivity over the particle distribution functions. The distribution function (e.g., Maxwellian) is depleted in the energy range determined by the highest reactivity and has to be replenished by particle collisions. The kinetics of the replenishment process may affect the rate of fusion energy release. We present a simple analysis of the corresponding kinetic problems for the conditions typical for the standard and advanced-fuel fusion reactions and assess the possible effect on the reaction yield.

Density Affects the Nature of the Hexatic-Liquid Transition in Two-Dimensional Melting of Soft-Core Systems

NASA Astrophysics Data System (ADS)

Zu, Mengjie; Liu, Jun; Tong, Hua; Xu, Ning

2016-08-01

We find that both continuous and discontinuous hexatic-liquid transitions can happen in the melting of two-dimensional solids of soft-core disks. For three typical model systems, Hertzian, harmonic, and Gaussian-core models, we observe the same scenarios. These systems exhibit reentrant crystallization (melting) with a maximum melting temperature Tm happening at a crossover density ρm. The hexatic-liquid transition at a density smaller than ρm is discontinuous. Liquid and hexatic phases coexist in a density interval, which becomes narrower with increasing temperature and tends to vanish approximately at Tm. Above ρm, the transition is continuous, in agreement with the Kosterlitz-Thouless-Halperin-Nelson-Young theory. For these soft-core systems, the nature of the hexatic-liquid transition depends on density (pressure), with the melting at ρm being a plausible transition point from discontinuous to continuous hexatic-liquid transition.

LIQUID-LIQUID EXTRACTION COLUMNS

DOEpatents

Thornton, J.D.

1957-12-31

This patent relates to liquid-liquid extraction columns having a means for pulsing the liquid in the column to give it an oscillatory up and down movement, and consists of a packed column, an inlet pipe for the dispersed liquid phase and an outlet pipe for the continuous liquid phase located in the direct communication with the liquid in the lower part of said column, an inlet pipe for the continuous liquid phase and an outlet pipe for the dispersed liquid phase located in direct communication with the liquid in the upper part of said column, a tube having one end communicating with liquid in the lower part of said column and having its upper end located above the level of said outlet pipe for the dispersed phase, and a piston and cylinder connected to the upper end of said tube for applying a pulsating pneumatic pressure to the surface of the liquid in said tube so that said surface rises and falls in said tube.

Bone marrow chimeric mice reveal a role for CX₃CR1 in maintenance of the monocyte-derived cell population in the olfactory neuroepithelium.

PubMed

Vukovic, Jana; Blomster, Linda V; Chinnery, Holly R; Weninger, Wolfgang; Jung, Steffen; McMenamin, Paul G; Ruitenberg, Marc J

2010-10-01

Macrophages in the olfactory neuroepithelium are thought to play major roles in tissue homeostasis and repair. However, little information is available at present about possible heterogeneity of these monocyte-derived cells, their turnover rates, and the role of chemokine receptors in this process. To start addressing these issues, this study used Cx₃cr1(gfp) mice, in which the gene sequence for eGFP was knocked into the CX₃CR1 gene locus in the mutant allele. Using neuroepithelial whole-mounts from Cx₃cr1(gfp/+) mice, we show that eGFP(+) cells of monocytic origin are distributed in a loose network throughout this tissue and can be subdivided further into two immunophenotypically distinct subsets based on MHC-II glycoprotein expression. BM chimeric mice were created using Cx₃cr1(gfp/+) donors to investigate turnover of macrophages (and other monocyte-derived cells) in the olfactory neuroepithelium. Our data indicate that the monocyte-derived cell population in the olfactory neuroepithelium is actively replenished by circulating monocytes and under the experimental conditions, completely turned over within 6 months. Transplantation of Cx₃cr1(gfp/gfp) (i.e., CX₃CR1-deficient) BM partially impaired the replenishment process and resulted in an overall decline of the total monocyte-derived cell number in the olfactory epithelium. Interestingly, replenishment of the CD68(low)MHC-II(+) subset appeared minimally affected by CX₃CR1 deficiency. Taken together, the established baseline data about heterogeneity of monocyte-derived cells, their replenishment rates, and the role of CX₃CR1 provide a solid basis to further examine the importance of different monocyte subsets for neuroregeneration at this unique frontier with the external environment.

Moving epithelia: Tracking the fate of mammalian limbal epithelial stem cells.

PubMed

Di Girolamo, Nick

2015-09-01

Lineage tracing allows the destiny of a stem cell (SC) and its progeny to be followed through time. In order to track their long-term fate, SC must be permanently marked to discern their distribution, division, displacement and differentiation. This information is essential for unravelling the mysteries that govern their replenishing activity while they remain anchored within their niche microenvironment. Modern-day lineage tracing uses inducible genetic recombination to illuminate cells within embryonic, newborn and adult tissues, and the advent of powerful high-resolution microscopy has enabled the behaviour of labelled cells to be monitored in real-time in a living organism. The simple structural organization of the mammalian cornea, including its accessibility and transparency, renders it the ideal tissue to study SC fate using lineage tracing assisted by non-invasive intravital microscopy. Despite more than a century of research devoted to understanding how this tissue is maintained and repaired, many limitations and controversies continue to plague the field, including uncertainties about the specificity of current SC markers, the number of SC within the cornea, their mode of division, their location, and importantly the signals that dictate cell migration. This communication will highlight historical discoveries as well as recent developments in the corneal SC field; more specifically how the progeny of these cells are mobilised to replenish this dynamic tissue during steady-state, disease and transplantation. Also discussed is how insights gleaned from animal studies can be used to advance our knowledge of the fundamental mechanisms that govern modelling and remodelling of the human cornea in health and disease. Copyright © 2015 Elsevier Ltd. All rights reserved.

Growing magma chambers control the distribution of small-scale flood basalts.

PubMed

Yu, Xun; Chen, Li-Hui; Zeng, Gang

2015-11-19

Small-scale continental flood basalts are a global phenomenon characterized by regular spatio-temporal distributions. However, no genetic mechanism has been proposed to explain the visible but overlooked distribution patterns of these continental basaltic volcanism. Here we present a case study from eastern China, combining major and trace element analyses with Ar-Ar and K-Ar dating to show that the spatio-temporal distribution of small-scale flood basalts is controlled by the growth of long-lived magma chambers. Evolved basalts (SiO2 > 47.5 wt.%) from Xinchang-Shengzhou, a small-scale Cenozoic flood basalt field in Zhejiang province, eastern China, show a northward younging trend over the period 9.4-3.0 Ma. With northward migration, the magmas evolved only slightly ((Na2O + K2O)/MgO = 0.40-0.66; TiO2/MgO = 0.23-0.35) during about 6 Myr (9.4-3.3 Ma). When the flood basalts reached the northern end of the province, the magmas evolved rapidly (3.3-3.0 Ma) through a broad range of compositions ((Na2O + K2O)/MgO = 0.60-1.28; TiO2/MgO = 0.30-0.57). The distribution and two-stage compositional evolution of the migrating flood basalts record continuous magma replenishment that buffered against magmatic evolution and induced magma chamber growth. Our results demonstrate that the magma replenishment-magma chamber growth model explains the spatio-temporal distribution of small-scale flood basalts.

Process for blending coal with water immiscible liquid

DOEpatents

Heavin, Leonard J.; King, Edward E.; Milliron, Dennis L.

1982-10-26

A continuous process for blending coal with a water immiscible liquid produces a uniform, pumpable slurry. Pulverized raw feed coal and preferably a coal derived, water immiscible liquid are continuously fed to a blending zone (12 and 18) in which coal particles and liquid are intimately admixed and advanced in substantially plug flow to form a first slurry. The first slurry is withdrawn from the blending zone (12 and 18) and fed to a mixing zone (24) where it is mixed with a hot slurry to form the pumpable slurry. A portion of the pumpable slurry is continuously recycled to the blending zone (12 and 18) for mixing with the feed coal.

40 CFR 63.2480 - What requirements must I meet for equipment leaks?

Code of Federal Regulations, 2013 CFR

2013-07-01

... connectors at your affected source. (5) For pumps in light liquid service in an MCPU that has no continuous... connectors in gas/vapor and light liquid service at an existing source, you may elect to comply with the... in light liquid service in an MCPU that has no continuous process vents and is part of an existing...

40 CFR 63.2480 - What requirements must I meet for equipment leaks?

Code of Federal Regulations, 2014 CFR

2014-07-01

... connectors at your affected source. (5) For pumps in light liquid service in an MCPU that has no continuous... connectors in gas/vapor and light liquid service at an existing source, you may elect to comply with the... in light liquid service in an MCPU that has no continuous process vents and is part of an existing...

40 CFR 63.2480 - What requirements must I meet for equipment leaks?

Code of Federal Regulations, 2012 CFR

2012-07-01

... connectors at your affected source. (5) For pumps in light liquid service in an MCPU that has no continuous... connectors in gas/vapor and light liquid service at an existing source, you may elect to comply with the... in light liquid service in an MCPU that has no continuous process vents and is part of an existing...

40 CFR 63.2480 - What requirements must I meet for equipment leaks?

Code of Federal Regulations, 2011 CFR

2011-07-01

... affected source. (5) For pumps in light liquid service in an MCPU that has no continuous process vents and.../vapor and light liquid service at an existing source, you may elect to comply with the requirements in... light liquid service in an MCPU that has no continuous process vents and is part of an existing source...

26 CFR 1.514(d)-1 - Basis of debt-financed property acquired in corporate liquidation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Basis of debt-financed property acquired in corporate liquidation. 1.514(d)-1 Section 1.514(d)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Taxation of Business...

Consolidated Bioprocessing for Butyric Acid Production from Rice Straw with Undefined Mixed Culture

PubMed Central

Ai, Binling; Chi, Xue; Meng, Jia; Sheng, Zhanwu; Zheng, Lili; Zheng, Xiaoyan; Li, Jianzheng

2016-01-01

Lignocellulosic biomass is a renewable source with great potential for biofuels and bioproducts. However, the cost of cellulolytic enzymes limits the utilization of the low-cost bioresource. This study aimed to develop a consolidated bioprocessing without the need of supplementary cellulase for butyric acid production from lignocellulosic biomass. A stirred-tank reactor with a working volume of 21 L was constructed and operated in batch and semi-continuous fermentation modes with a cellulolytic butyrate-producing microbial community. The semi-continuous fermentation with intermittent discharging of the culture broth and replenishment with fresh medium achieved the highest butyric acid productivity of 2.69 g/(L· d). In semi-continuous operation mode, the butyric acid and total carboxylic acid concentrations of 16.2 and 28.9 g/L, respectively, were achieved. Over the 21-day fermentation period, their cumulative yields reached 1189 and 2048 g, respectively, corresponding to 41 and 74% of the maximum theoretical yields based on the amount of NaOH pretreated rice straw fed in. This study demonstrated that an undefined mixed culture-based consolidated bioprocessing for butyric acid production can completely eliminate the cost of supplementary cellulolytic enzymes. PMID:27822203

Consolidated Bioprocessing for Butyric Acid Production from Rice Straw with Undefined Mixed Culture.

PubMed

Ai, Binling; Chi, Xue; Meng, Jia; Sheng, Zhanwu; Zheng, Lili; Zheng, Xiaoyan; Li, Jianzheng

2016-01-01

Lignocellulosic biomass is a renewable source with great potential for biofuels and bioproducts. However, the cost of cellulolytic enzymes limits the utilization of the low-cost bioresource. This study aimed to develop a consolidated bioprocessing without the need of supplementary cellulase for butyric acid production from lignocellulosic biomass. A stirred-tank reactor with a working volume of 21 L was constructed and operated in batch and semi-continuous fermentation modes with a cellulolytic butyrate-producing microbial community. The semi-continuous fermentation with intermittent discharging of the culture broth and replenishment with fresh medium achieved the highest butyric acid productivity of 2.69 g/(L· d). In semi-continuous operation mode, the butyric acid and total carboxylic acid concentrations of 16.2 and 28.9 g/L, respectively, were achieved. Over the 21-day fermentation period, their cumulative yields reached 1189 and 2048 g, respectively, corresponding to 41 and 74% of the maximum theoretical yields based on the amount of NaOH pretreated rice straw fed in. This study demonstrated that an undefined mixed culture-based consolidated bioprocessing for butyric acid production can completely eliminate the cost of supplementary cellulolytic enzymes.

The calculation of transport properties in quantum liquids using the maximum entropy numerical analytic continuation method: Application to liquid para-hydrogen

PubMed Central

Rabani, Eran; Reichman, David R.; Krilov, Goran; Berne, Bruce J.

2002-01-01

We present a method based on augmenting an exact relation between a frequency-dependent diffusion constant and the imaginary time velocity autocorrelation function, combined with the maximum entropy numerical analytic continuation approach to study transport properties in quantum liquids. The method is applied to the case of liquid para-hydrogen at two thermodynamic state points: a liquid near the triple point and a high-temperature liquid. Good agreement for the self-diffusion constant and for the real-time velocity autocorrelation function is obtained in comparison to experimental measurements and other theoretical predictions. Improvement of the methodology and future applications are discussed. PMID:11830656

Modeling and optimization of the multiobjective stochastic joint replenishment and delivery problem under supply chain environment.

PubMed

Wang, Lin; Qu, Hui; Liu, Shan; Dun, Cai-xia

2013-01-01

As a practical inventory and transportation problem, it is important to synthesize several objectives for the joint replenishment and delivery (JRD) decision. In this paper, a new multiobjective stochastic JRD (MSJRD) of the one-warehouse and n-retailer systems considering the balance of service level and total cost simultaneously is proposed. The goal of this problem is to decide the reasonable replenishment interval, safety stock factor, and traveling routing. Secondly, two approaches are designed to handle this complex multi-objective optimization problem. Linear programming (LP) approach converts the multi-objective to single objective, while a multi-objective evolution algorithm (MOEA) solves a multi-objective problem directly. Thirdly, three intelligent optimization algorithms, differential evolution algorithm (DE), hybrid DE (HDE), and genetic algorithm (GA), are utilized in LP-based and MOEA-based approaches. Results of the MSJRD with LP-based and MOEA-based approaches are compared by a contrastive numerical example. To analyses the nondominated solution of MOEA, a metric is also used to measure the distribution of the last generation solution. Results show that HDE outperforms DE and GA whenever LP or MOEA is adopted.

Modeling and Optimization of the Multiobjective Stochastic Joint Replenishment and Delivery Problem under Supply Chain Environment

PubMed Central

Dun, Cai-xia

2013-01-01

As a practical inventory and transportation problem, it is important to synthesize several objectives for the joint replenishment and delivery (JRD) decision. In this paper, a new multiobjective stochastic JRD (MSJRD) of the one-warehouse and n-retailer systems considering the balance of service level and total cost simultaneously is proposed. The goal of this problem is to decide the reasonable replenishment interval, safety stock factor, and traveling routing. Secondly, two approaches are designed to handle this complex multi-objective optimization problem. Linear programming (LP) approach converts the multi-objective to single objective, while a multi-objective evolution algorithm (MOEA) solves a multi-objective problem directly. Thirdly, three intelligent optimization algorithms, differential evolution algorithm (DE), hybrid DE (HDE), and genetic algorithm (GA), are utilized in LP-based and MOEA-based approaches. Results of the MSJRD with LP-based and MOEA-based approaches are compared by a contrastive numerical example. To analyses the nondominated solution of MOEA, a metric is also used to measure the distribution of the last generation solution. Results show that HDE outperforms DE and GA whenever LP or MOEA is adopted. PMID:24302880

Genetic connectivity and self-replenishment of inshore and offshore populations of the endemic anemonefish, Amphiprion latezonatus

NASA Astrophysics Data System (ADS)

Steinberg, Rosemary; van der Meer, Martin; Walker, Emily; Berumen, Michael L.; Hobbs, Jean-Paul A.; van Herwerden, Lynne

2016-09-01

Globally, marine species are under increasing pressure from human activities, including ocean warming, acidification, pollution, and overfishing. Species most vulnerable to these pressures tend to be ecological specialists that have low abundance and small distribution ranges (endemics). Marine endemics often exist as meta-populations distributed among few isolated locations. Determining genetic connectivity among these locations is essential to understanding the recovery potential of endemics after local extinction events. This study examined connectivity in the endemic anemonefish, Amphiprion latezonatus, a habitat specialist with low abundance at most locations. Evolutionary and contemporary migration, genetic diversity, and self-replenishment among the four main locations (Sunshine Coast, North Solitary Island, Lord Howe Island, and Norfolk Island) that comprise the entire A. latezonatus geographic range were assessed using mtDNA and microsatellite markers. Though historical gene flow inferred from mtDNA appeared high, population genetic differentiation was evident and contemporary gene flow inferred from microsatellites was limited, alongside very high (≥89 %) self-replenishment at all locations. Together, these data suggest prolonged recovery times following severe population decline (or extirpation) and indicate a need to protect this species at all locations, particularly Norfolk Island and Sunshine Coast where marine protected areas are lacking.

Source memory in the rat

PubMed Central

Crystal, Jonathon D.; Alford, Wesley T.; Zhou, Wenyi; Hohmann, Andrea G.

2013-01-01

Summary Source memory is a representation of the origin (source) of information. When source information is bound together, it makes a memory episodic, allowing us to differentiate one event from another [1, 2]. Here we asked if rats remember the source of encoded information. Rats foraged for distinctive flavors of food that replenished (or failed to replenish) at its recently encountered location according to a source-information rule. To predict replenishment, rats needed to remember where they had encountered a preferred food type (chocolate) with self-generated (walking along a runway encountering chocolate) or experimenter-generated (placement of the rat at the chocolate site by an experimenter) cues. Three lines of evidence implicate the presence of source memory. First, rats selectively adjusted revisits to the chocolate location based on source information, under conditions in which familiarity of events could not produce successful performance. Second, source memory was dissociated from location memory by different decay rates. Third, temporary inactivation of the CA3 region of the hippocampus with lidocaine selectively eliminated source memory, suggesting that source memory is dependent upon an intact hippocampus. Development of an animal model of source memory may be valuable to probe the biological underpinnings of memory disorders marked by impairments in source memory. PMID:23394830

The concept of energy height in animal locomotion: separating mechanics from physiology.

PubMed

Pennycuick, C J

2003-09-21

The distance flown in gliding is proportional to the starting height, not to the starting potential energy, and it is independent of the body mass. By analogy, in powered flight, the quantity of stored fuel can be converted into a virtual "fuel energy height", defined as the height to which the fuel energy could lift the bird against gravity, if it were converted into work. This is a logarithmic function of the fuel fraction, not of the absolute amount of fuel, or of the body mass. It takes account of the strength of gravity, and of the efficiency with which fuel energy is converted into work. The "performance number" is the gradient on which a migrating bird comes "down" from its initial fuel energy height. It is mechanical (not physiological) in character, and corresponds to the lift:drag ratio in a fixed-wing aircraft. The concept of range as an initial energy height multiplied by a performance number can also be applied to swimming and running animals. Performance number, and also the related variable "cost of transport", are both independent of gravity in flying and running, but not in swimming. Migration by thermal soaring is analogous to powered flight with stopovers, except that the bird replenishes its potential energy by climbing in thermals, rather than replenishing fuel energy during stopovers. Rates of climb in thermals are typically higher than fuel energy rates of climb, but the available height band is two orders of magnitude smaller, and the intervals at which energy replenishment is needed are correspondingly shorter. Albatrosses replenish their kinetic energy by exploiting discontinuities in the wind flow over waves, requiring replenishment at intervals of tens of seconds, a further two orders of magnitude shorter than in thermal soaring. Fat energy height can be used as a measure of "condition", which is independent of the size or type of the animal. The fat energy height at which a migrant must arrive on the breeding grounds, in order to breed successfully, reflects the ecological characteristics of the habitat, not the size or character of the bird. Energy height expresses what an animal or machine can do with its stored energy, not the amount of energy.

Constraints on the Rates of Replenishment, Magma Mixing, and Crystal Recycling at Santorini Volcano, Greece

NASA Astrophysics Data System (ADS)

Martin, V. M.; Davidson, J. P.; Morgan, D. J.; Jerram, D. A.

2007-12-01

Santorini is a young, active volcano, which preserves abundant evidence for open-system processes such as magma replenishment and crystal recycling, and thus represents an ideal system in which to study magma chamber dynamics. Santorini is the largest volcanic centre in the Aegean arc, with an eruptive history spanning more than 250,000 years over two eruptive cycles. The cycles are dominated by extended periods of effusive shield-building activity with occasional large-magnitude explosive eruptions, the Minoan eruption of ~3600 years ago being the most recent. Current activity consists of a phase of post-caldera reconstruction, focused recently on the intra-caldera Kameni islands. Microsampling to measure 87Sr/86Sr ratios of plagioclase cores indicates the presence of a complex plumbing system beneath Santorini. Large rhyodacitic deposits typically contain a mafic component, interpreted as the eruption trigger. In some cases, the mafic magma groundmass and phenocrysts are isotopically similar to their rhyodacite host; other deposits show the opposite, implying the coexistence of isotopically distinct magma batches. To add further complexity, plagioclase phenocrysts are in some cases in equilibrium with their groundmass while others show the reverse, implying modification due to crystal recycling or shallow mixing processes prior to eruption. Mafic enclaves in the recent Kameni lavas, again interpreted as the probable eruption trigger, provide some constraints on the rates of these recycling, mixing, and triggering processes. Glomerocrysts and xenocrysts of recycled gabbroic cumulate material are present in a number of Kameni enclaves. Isotopic and chemical disequilibrium between the cumulate crystals and the host indicate that these fragments are derived from pre- existing crystal mush piles pervaded by the replenishing melts as they migrated to shallow levels, creating disequilibrium between the cumulate mineral cores and the replenishing melts. 87Sr/86Sr isotope ratios of plagioclase xenocryst cores suggest crystal recycling from a pre-Minoan source is probable. Olivine xenocrysts in the enclaves possess narrow (10-30 μm) Fe-Mg diffusion profiles, due to interaction with enclave magma groundmass, which can be used to estimate the interval between entrainment and eruption. Initial modelling of diffusion profiles from more than 60 crystals suggests short timescales, from 15 to 45 days, for the combined migration-replenishment-eruption cycle at Kameni.

Advanced Water Purification System for In Situ Resource Utilization

NASA Technical Reports Server (NTRS)

Anthony, Stephen M.; Jolley, Scott T.; Captain, James G.

2013-01-01

One of NASA's goals is to enable longterm human presence in space, without the need for continuous replenishment of consumables from Earth. In situ resource utilization (ISRU) is the use of extraterrestrial resources to support activities such as human life-support, material fabrication and repair, and radiation shielding. Potential sources of ISRU resources include lunar and Martian regolith, and Martian atmosphere. Water and byproducts (including hydrochloric and hydrofluoric acids) can be produced from lunar regolith via a high-temperature hydrogen reduction reaction and passing the produced gas through a condenser. center dot Due to the high solubility of HCI and HF in water, these byproducts are expected to be present in the product stream (up to 20,000 ppm) and must be removed (less than 10 ppm) prior to water consumption or electrolysis.

Constant replenishment from circulating monocytes maintains the macrophage pool in adult intestine

PubMed Central

Scott, Charlotte L.; Perdiguero, Elisa Gomez; Geissmann, Frederic; Henri, Sandrine; Malissen, Bernard; Osborne, Lisa C.; Artis, David; Mowat, Allan McI.

2014-01-01

The paradigm that resident macrophages in steady-state tissues are derived from embryonic precursors has never been investigated in the intestine, which contains the largest pool of macrophages. Using fate mapping models and monocytopenic mice, together with bone marrow chimeric and parabiotic models, we show that embryonic precursors seeded the intestinal mucosa and demonstrated extensive in situ proliferation in the neonatal period. However these cells did not persist in adult intestine. Instead, they were replaced around the time of weaning by the CCR2-dependent influx of Ly6Chi monocytes that differentiated locally into mature, anti-inflammatory macrophages. This process was driven largely by the microbiota and had to be continued throughout adult life to maintain a normal intestinal macrophage pool. PMID:25151491

Clump detections and limits on moons in Jupiter's ring system.

PubMed

Showalter, Mark R; Cheng, Andrew F; Weaver, Harold A; Stern, S Alan; Spencer, John R; Throop, Henry B; Birath, Emma M; Rose, Debi; Moore, Jeffrey M

2007-10-12

The dusty jovian ring system must be replenished continuously from embedded source bodies. The New Horizons spacecraft has performed a comprehensive search for kilometer-sized moons within the system, which might have revealed the larger members of this population. No new moons were found, however, indicating a sharp cutoff in the population of jovian bodies smaller than 8-kilometer-radius Adrastea. However, the search revealed two families of clumps in the main ring: one close pair and one cluster of three to five. All orbit within a brighter ringlet just interior to Adrastea. Their properties are very different from those of the few other clumpy rings known; the origin and nonrandom distribution of these features remain unexplained, but resonant confinement by Metis may play a role.

Continuing life test of a xenon hollow cathode for a space plasma contactor

NASA Technical Reports Server (NTRS)

Sarver-Verhey, Timothy R.

1994-01-01

Implementation of a hollow cathode plasma contactor for charge control on the Space Station has required validation of long-life hollow cathodes. A test series of hollow cathodes and hollow cathode plasma contactors was initiated as part of the plasma contactor development program. An on-going wear-test of a hollow cathode has demonstrated cathode operation in excess of 10,000 hours with small changes in operating parameters. The discharge has experienced 10 shutdowns during the test, all of which were due to test facility failures or expellant replenishment. In all cases, the cathode was re-ignited at approximately 42 volts and resumed typical operation. This test represents the longest demonstrated stable operation of a high current (greater than 1 A) xenon hollow cathode reported to date.

Continuous monitoring of the progressive degradation of a liquid composite by means of a noninvasive microwave resonator

NASA Astrophysics Data System (ADS)

Catala-Civera, Jose M.; Canos-Marin, Antoni J.; de los Reyes, E.

2000-07-01

Microwave control capabilities have been used to monitor the degradation of polyol, an alcohol composite material commonly used in the footwear industry for polymerization purposes. The liquid flows continuously inside a thin pipe and its desirable properties are altered with time associated to moisture absorption processes. Consequently, variations in the dielectric properties are involved, and they can be detected by permittivity measurements. In this paper, in order to obtain high sensitivity and resolution, a rectangular cavity resonator working at a fixed frequency was designed using as sample holder a rectangular pipe containing the liquid going through. Changes in the liquid modify the original response of the cavity with a non- degraded liquid and these differences have been used to determine the degree of degradation of the material. The final response of the microwave resonator was experimentally validated with measurements in a continuous line.

26 CFR 1.514(d)-1 - Basis of debt-financed property acquired in corporate liquidation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Taxation of Business... value of $47,000. M recognizes gain of $6,000 with respect to this liquidation pursuant to sections 1245 and 1250. T realizes a gain of $25,000 (the difference between the excess of fair market value of the...

Analytical and experimental investigation of liquid double drop dynamics: Preliminary design for space shuttle experiments

NASA Technical Reports Server (NTRS)

1981-01-01

The preliminary grant assessed the use of laboratory experiments for simulating low g liquid drop experiments in the space shuttle environment. Investigations were begun of appropriate immiscible liquid systems, design of experimental apparatus and analyses. The current grant continued these topics, completed construction and preliminary testing of the experimental apparatus, and performed experiments on single and compound liquid drops. A continuing assessment of laboratory capabilities, and the interests of project personnel and available collaborators, led to, after consultations with NASA personnel, a research emphasis specializing on compound drops consisting of hollow plastic or elastic spheroids filled with liquids.

7 CFR 1980.471 - Liquidation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM... the cost of liquidation exceeds the potential recovery value of the collection. Whenever this occurs...

Assessment of offshore New Jersey sources of Beach replenishment sand by diversified application of geologic and geophysical methods

USGS Publications Warehouse

Waldner, J.S.; Hall, D.W.; Uptegrove, J.; Sheridan, R.E.; Ashley, G.M.; Esker, D.

1999-01-01

Beach replenishment serves the dual purpose of maintaining a source of tourism and recreation while protecting life and property. For New Jersey, sources for beach sand supply are increasingly found offshore. To meet present and future needs, geologic and geophysical techniques can be used to improve the identification, volume estimation, and determination of suitability, thereby making the mining and managing of this resource more effective. Current research has improved both data collection and interpretation of seismic surveys and vibracore analysis for projects investigating sand ridges offshore of New Jersey. The New Jersey Geological Survey in cooperation with Rutgers University is evaluating the capabilities of digital seismic data (in addition to analog data) to analyze sand ridges. The printing density of analog systems limits the dynamic range to about 24 dB. Digital acquisition systems with dynamic ranges above 100 dB can permit enhanced seismic profiles by trace static correction, deconvolution, automatic gain scaling, horizontal stacking and digital filtering. Problems common to analog data, such as wave-motion effects of surface sources, water-bottom reverberation, and bubble-pulse-width can be addressed by processing. More than 160 line miles of digital high-resolution continuous profiling seismic data have been collected at sand ridges off Avalon, Beach Haven, and Barnegat Inlet. Digital multichannel data collection has recently been employed to map sand resources within the Port of New York/New Jersey expanded dredge-spoil site located 3 mi offshore of Sandy Hook, New Jersey. Multichannel data processing can reduce multiples, improve signal-to-noise calculations, enable source deconvolution, and generate sediment acoustic velocities and acoustic impedance analysis. Synthetic seismograms based on empirical relationships among grain size distribution, density, and velocity from vibracores are used to calculate proxy values for density and velocity. The seismograms are then correlated to the digital seismic profile to confirm reflected events. They are particularly useful where individual reflection events cannot be detected but a waveform generated by several thin lithologic units can be recognized. Progress in application of geologic and geophysical methods provides advantages in detailed sediment analysis and volumetric estimation of offshore sand ridges. New techniques for current and ongoing beach replenishment projects not only expand our knowledge of the geologic processes involved in sand ridge origin and development, but also improve our assessment of these valuable resources. These reconnaissance studies provide extensive data to the engineer regarding the suitability and quantity of sand and can optimize placement and analysis of vibracore samples.Beach replenishment serves the dual purpose of maintaining a source of tourism and recreation while protecting life and property. Research has improved both data collection and interpretation of seismic surveys and vibracore analysis for projects investigating sand ridges offshore of New Jersey. The New Jersey Geological Survey in cooperation with Rutgers University is evaluating the capabilities of digital seismic data to analyze sand ridges. The printing density of analog systems limits the dynamic range to about 24 dB. Digital acquisition systems with dynamic ranges about 100 dB can permit enhanced seismic profiles by trace static correction, deconvolution, automatic gain scaling, horizontal stacking and digital filtering.

Visualization and understanding of the granulation liquid mixing and distribution during continuous twin screw granulation using NIR chemical imaging.

PubMed

Vercruysse, Jurgen; Toiviainen, Maunu; Fonteyne, Margot; Helkimo, Niko; Ketolainen, Jarkko; Juuti, Mikko; Delaet, Urbain; Van Assche, Ivo; Remon, Jean Paul; Vervaet, Chris; De Beer, Thomas

2014-04-01

Over the last decade, there has been increased interest in the application of twin screw granulation as a continuous wet granulation technique for pharmaceutical drug formulations. However, the mixing of granulation liquid and powder material during the short residence time inside the screw chamber and the atypical particle size distribution (PSD) of granules produced by twin screw granulation is not yet fully understood. Therefore, this study aims at visualizing the granulation liquid mixing and distribution during continuous twin screw granulation using NIR chemical imaging. In first instance, the residence time of material inside the barrel was investigated as function of screw speed and moisture content followed by the visualization of the granulation liquid distribution as function of different formulation and process parameters (liquid feed rate, liquid addition method, screw configuration, moisture content and barrel filling degree). The link between moisture uniformity and granule size distributions was also studied. For residence time analysis, increased screw speed and lower moisture content resulted to a shorter mean residence time and narrower residence time distribution. Besides, the distribution of granulation liquid was more homogenous at higher moisture content and with more kneading zones on the granulator screws. After optimization of the screw configuration, a two-level full factorial experimental design was performed to evaluate the influence of moisture content, screw speed and powder feed rate on the mixing efficiency of the powder and liquid phase. From these results, it was concluded that only increasing the moisture content significantly improved the granulation liquid distribution. This study demonstrates that NIR chemical imaging is a fast and adequate measurement tool for allowing process visualization and hence for providing better process understanding of a continuous twin screw granulation system. Copyright © 2013 Elsevier B.V. All rights reserved.

Electrical-analog analysis of ground-water depletion in central Arizona

USGS Publications Warehouse

Anderson, T.W.

1968-01-01

The Salt River Valley and the lower Santa Cruz River basin are the two largest agricultural areas in Arizona. The extensive use of ground water for irrigation has resulted in the need for a thorough appraisal of the present and future ground-water resources. The ground-water reservoir provides 80 percent (3.2 million acre-feet) of the total annual water supply. The amount of water pumped greatly exceeds the rate at which the ground-water supply is being replenished and has resulted in water-level declines of as much as 20 feet per year in some places. The depletion problem is of economic importance because ground water will become more expensive as pumping lifts increase and well yields decrease. The use of electrical-analog modeling techniques has made it possible to predict future ground-water levels under conditions of continued withdrawal in excess of the rate of replenishment. The electrical system is a representation of the hydrologic system: resistors and capacitors represent transmissibility and storage coefficients. The analogy between the two systems is accepted when the data obtained from the model closely match the field data in this instance, measured water-level change since 1923. The prediction of future water-table conditions is accomplished by a simple extension of the pumping trends to determine the resultant effect on the regional water levels. The results of this study indicate the probable depths to water in central Arizona in 1974 and 1984 if the aquifer characteristics are accurately modeled and if withdrawal of ground water continues at the same rate and under the tame areal distribution as existed between 1958 and 1964. The greatest depths to water in 1984 will be more than 700 feet near Stanfield and more than 650 feet in Deer Valley and northeast of Gilbert. South of Eloy and northwest of Litchfield Park, a static water level of more than 550 feet is predicted. The total water-level decline in the 20-year period 1964-84 at the deepest points of the major cones of depression will range from 150 to 300 feet, and the average decline in the entire central Arizona area will be about 100 feet.

Comparison of surfactant lipids between pleural and pulmonary lining fluids.

PubMed

Mills, P C; Chen, Y; Hills, Y C; Hills, B A

2006-01-01

Saturated phospholipids (PCs), particularly dipalmitoylphosphatidylcholine (DPPC), predominate in surfactant lining the alveoli, although little is known about the relationship between saturated and unsaturated PCs on the outer surface of the lung, the pleura. Seven healthy cats were anesthetized and a bronchoalveolar lavage (BAL) was performed, immediately followed by a pleural lavage (PL). Lipid was extracted from lavage fluid and then analyzed for saturated, primarily dipalmitoylphosphatidylcholine (DPPC), and unsaturated PC species using high-performance liquid chromatography (HPLC) with combined fluorescence and ultraviolet detection. Dilution of epithelial lining fluid (ELF) in lavage fluids was corrected for using the urea method. The concentration of DPPC in BAL fluid (85.3+/-15.7 microg/mL) was significantly higher (P=0.021) than unsaturated PCs ( approximately 40 microg/mL). However, unsaturated PCs ( approximately 34 microg/mL), particularly stearoyl-linoleoyl-phosphatidylcholine (SLPC; 17.4+/-6.8), were significantly higher (P=0.021) than DPPC (4.3+/-1.8 microg/mL) in PL fluid. These results show that unsaturated PCs appear functionally more important in the pleural cavity, which may have implications for surfactant replenishment following pleural disease or thoracic surgery.

Pricing policy for declining demand using item preservation technology.

PubMed

Khedlekar, Uttam Kumar; Shukla, Diwakar; Namdeo, Anubhav

2016-01-01

We have designed an inventory model for seasonal products in which deterioration can be controlled by item preservation technology investment. Demand for the product is considered price sensitive and decreases linearly. This study has shown that the profit is a concave function of optimal selling price, replenishment time and preservation cost parameter. We simultaneously determined the optimal selling price of the product, the replenishment cycle and the cost of item preservation technology. Additionally, this study has shown that there exists an optimal selling price and optimal preservation investment to maximize the profit for every business set-up. Finally, the model is illustrated by numerical examples and sensitive analysis of the optimal solution with respect to major parameters.

Totally Integrated Munitions Enterprise ''Affordable Munitions Production for the 21st Century''

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burleson, R.R.; Poggio, M.E.; Rosenberg, S.J.

2000-09-13

The U.S. Army faces several munitions manufacturing issues: downsizing of the organic production base, timely fielding of affordable smart munitions, and munitions replenishment during national emergencies. Totally Integrated Munitions Enterprise (TIME) is addressing these complex issues via the development and demonstration of an integrated enterprise. The enterprise will include the tools, network, and open modular architecture controllers to enable accelerated acquisition, shortened concept to volume production, lower life cycle costs, capture of critical manufacturing processes, and communication of process parameters between remote sites to rapidly spin-off production for replenishment by commercial sources. TIME addresses the enterprise as a system, integratingmore » design, engineering, manufacturing, administration, and logistics.« less

Totally Integrated Munitions Enterprise ''Affordable Munitions Production for the 21st Century''

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burleson, R.R.; Poggio, M.E.; Rosenberg, S.J.

2000-07-14

The U.S. Army faces several munitions manufacturing issues: downsizing of the organic production base, timely fielding of affordable smart munitions, and munitions replenishment during national emergencies. TIME is addressing these complex issues via the development and demonstration of an integrated enterprise. The enterprise will include the tools, network, and open modular architecture controller to enable accelerated acquisition, shortened concept to volume production, lower life cycle costs, capture of critical manufacturing processes, and communication of process parameters between remote sites to rapidly spin-off production for replenishment by commercial sources. TIME addresses the enterprise as a system, integrating design, engineering, manufacturing, administration,more » and logistics.« less

Totally Integrated Munitions Enterprise ''Affordable Munitions Production for the 21st Century''

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burleson, R.R.; Poggio, M.E.; Rosenberg, S.J.

2000-08-18

The U.S. Army faces several munitions manufacturing issues: downsizing of the organic production base, timely fielding of affordable smart munitions, and munitions replenishment during national emergencies. Totally Integrated Munitions Enterprise (TIME) is addressing these complex issues via the development and demonstration of an integrated enterprise. The enterprise will include the tools, network, and open modular architecture controllers to enable accelerated acquisition, shortened concept to volume production, lower life cycle costs, capture of critical manufacturing processes, and communication of process parameters between remote sites to rapidly spin-off production for replenishment by commercial sources. TIME addresses the enterprise as a system, integratingmore » design, engineering, manufacturing, administration, and logistics.« less

Liquid biopsy for brain tumors

PubMed Central

Shankar, Ganesh M.; Balaj, Leonora; Stott, Shannon L.; Nahed, Brian; Carter, Bob S.

2018-01-01

Introduction Minimally invasive methods will augment the clinical approach for establishing the diagnosis or monitoring treatment response of central nervous system tumors. Liquid biopsy by blood or cerebrospinal fluid sampling holds promise in this regard. Areas covered In this literature review, the authors highlight recent studies describing the analysis of circulating tumor cells, cell free nucleic acids, and extracellular vesicles as strategies to accomplish liquid biopsy in glioblastoma and metastatic tumors. The authors then discuss the continued efforts to improve signal detection, standardize the liquid biopsy handling and preparation, develop platforms for clinical application, and establish a role for liquid biopsies in personalized medicine. Expert commentary As the technologies used to analyze these biomarkers continue to evolve, we propose that there is a future potential to precisely diagnose and monitor treatment response with liquid biopsies. PMID:28875730

Liquid biopsy for brain tumors.

PubMed

Shankar, Ganesh M; Balaj, Leonora; Stott, Shannon L; Nahed, Brian; Carter, Bob S

2017-10-01

Minimally invasive methods will augment the clinical approach for establishing the diagnosis or monitoring treatment response of central nervous system tumors. Liquid biopsy by blood or cerebrospinal fluid sampling holds promise in this regard. Areas covered: In this literature review, the authors highlight recent studies describing the analysis of circulating tumor cells, cell free nucleic acids, and extracellular vesicles as strategies to accomplish liquid biopsy in glioblastoma and metastatic tumors. The authors then discuss the continued efforts to improve signal detection, standardize the liquid biopsy handling and preparation, develop platforms for clinical application, and establish a role for liquid biopsies in personalized medicine. Expert commentary: As the technologies used to analyze these biomarkers continue to evolve, we propose that there is a future potential to precisely diagnose and monitor treatment response with liquid biopsies.

Online Calibration of Polytomous Items Under the Generalized Partial Credit Model

PubMed Central

Zheng, Yi

2016-01-01

Online calibration is a technology-enhanced architecture for item calibration in computerized adaptive tests (CATs). Many CATs are administered continuously over a long term and rely on large item banks. To ensure test validity, these item banks need to be frequently replenished with new items, and these new items need to be pretested before being used operationally. Online calibration dynamically embeds pretest items in operational tests and calibrates their parameters as response data are gradually obtained through the continuous test administration. This study extends existing formulas, procedures, and algorithms for dichotomous item response theory models to the generalized partial credit model, a popular model for items scored in more than two categories. A simulation study was conducted to investigate the developed algorithms and procedures under a variety of conditions, including two estimation algorithms, three pretest item selection methods, three seeding locations, two numbers of score categories, and three calibration sample sizes. Results demonstrated acceptable estimation accuracy of the two estimation algorithms in some of the simulated conditions. A variety of findings were also revealed for the interacted effects of included factors, and recommendations were made respectively. PMID:29881063

21 CFR 524.86 - Amitraz liquid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.86 Amitraz liquid... treatments, 14 days apart. (3) Limitations. Continue treatment until no viable mites are found in skin...

21 CFR 524.86 - Amitraz liquid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.86 Amitraz liquid... treatments, 14 days apart. (3) Limitations. Continue treatment until no viable mites are found in skin...

21 CFR 524.86 - Amitraz liquid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.86 Amitraz liquid... treatments, 14 days apart. (3) Limitations. Continue treatment until no viable mites are found in skin...

21 CFR 524.86 - Amitraz liquid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.86 Amitraz liquid... treatments, 14 days apart. (3) Limitations. Continue treatment until no viable mites are found in skin...

Source memory in the rat.

PubMed

Crystal, Jonathon D; Alford, Wesley T; Zhou, Wenyi; Hohmann, Andrea G

2013-03-04

Source memory is a representation of the origin (source) of information. When source information is bound together, it makes a memory episodic, allowing us to differentiate one event from another. Here, we asked whether rats remember the source of encoded information. Rats foraged for distinctive flavors of food that replenished (or failed to replenish) at its recently encountered location according to a source-information rule. To predict replenishment, rats needed to remember where they had encountered a preferred food type (chocolate) with self-generated (walking along a runway encountering chocolate) or experimenter-generated (placement of the rat at the chocolate site by an experimenter) cues. Three lines of evidence implicate the presence of source memory. First, rats selectively adjusted revisits to the chocolate location based on source information, under conditions in which familiarity of events could not produce successful performance. Second, source memory was dissociated from location memory by different decay rates. Third, temporary inactivation of the CA3 region of the hippocampus with lidocaine selectively eliminated source memory, suggesting that source memory is dependent upon an intact hippocampus. Development of an animal model of source memory may be valuable to probe the biological underpinnings of memory disorders marked by impairments in source memory. Copyright © 2013 Elsevier Ltd. All rights reserved.

Real-Time Model-Based Leak-Through Detection within Cryogenic Flow Systems

NASA Technical Reports Server (NTRS)

Walker, M.; Figueroa, F.

2015-01-01

The timely detection of leaks within cryogenic fuel replenishment systems is of significant importance to operators on account of the safety and economic impacts associated with material loss and operational inefficiencies. Associated loss in control of pressure also effects the stability and ability to control the phase of cryogenic fluids during replenishment operations. Current research dedicated to providing Prognostics and Health Management (PHM) coverage of such cryogenic replenishment systems has focused on the detection of leaks to atmosphere involving relatively simple model-based diagnostic approaches that, while effective, are unable to isolate the fault to specific piping system components. The authors have extended this research to focus on the detection of leaks through closed valves that are intended to isolate sections of the piping system from the flow and pressurization of cryogenic fluids. The described approach employs model-based detection of leak-through conditions based on correlations of pressure changes across isolation valves and attempts to isolate the faults to specific valves. Implementation of this capability is enabled by knowledge and information embedded in the domain model of the system. The approach has been used effectively to detect such leak-through faults during cryogenic operational testing at the Cryogenic Testbed at NASA's Kennedy Space Center.

An effective hybrid self-adapting differential evolution algorithm for the joint replenishment and location-inventory problem in a three-level supply chain.

PubMed

Wang, Lin; Qu, Hui; Chen, Tao; Yan, Fang-Ping

2013-01-01

The integration with different decisions in the supply chain is a trend, since it can avoid the suboptimal decisions. In this paper, we provide an effective intelligent algorithm for a modified joint replenishment and location-inventory problem (JR-LIP). The problem of the JR-LIP is to determine the reasonable number and location of distribution centers (DCs), the assignment policy of customers, and the replenishment policy of DCs such that the overall cost is minimized. However, due to the JR-LIP's difficult mathematical properties, simple and effective solutions for this NP-hard problem have eluded researchers. To find an effective approach for the JR-LIP, a hybrid self-adapting differential evolution algorithm (HSDE) is designed. To verify the effectiveness of the HSDE, two intelligent algorithms that have been proven to be effective algorithms for the similar problems named genetic algorithm (GA) and hybrid DE (HDE) are chosen to compare with it. Comparative results of benchmark functions and randomly generated JR-LIPs show that HSDE outperforms GA and HDE. Moreover, a sensitive analysis of cost parameters reveals the useful managerial insight. All comparative results show that HSDE is more stable and robust in handling this complex problem especially for the large-scale problem.

An Effective Hybrid Self-Adapting Differential Evolution Algorithm for the Joint Replenishment and Location-Inventory Problem in a Three-Level Supply Chain

PubMed Central

Chen, Tao; Yan, Fang-Ping

2013-01-01

The integration with different decisions in the supply chain is a trend, since it can avoid the suboptimal decisions. In this paper, we provide an effective intelligent algorithm for a modified joint replenishment and location-inventory problem (JR-LIP). The problem of the JR-LIP is to determine the reasonable number and location of distribution centers (DCs), the assignment policy of customers, and the replenishment policy of DCs such that the overall cost is minimized. However, due to the JR-LIP's difficult mathematical properties, simple and effective solutions for this NP-hard problem have eluded researchers. To find an effective approach for the JR-LIP, a hybrid self-adapting differential evolution algorithm (HSDE) is designed. To verify the effectiveness of the HSDE, two intelligent algorithms that have been proven to be effective algorithms for the similar problems named genetic algorithm (GA) and hybrid DE (HDE) are chosen to compare with it. Comparative results of benchmark functions and randomly generated JR-LIPs show that HSDE outperforms GA and HDE. Moreover, a sensitive analysis of cost parameters reveals the useful managerial insight. All comparative results show that HSDE is more stable and robust in handling this complex problem especially for the large-scale problem. PMID:24453822

Regulation of Dense-Core Granule Replenishment by Autocrine BMP Signalling in Drosophila Secondary Cells.

PubMed

Redhai, Siamak; Hellberg, Josephine E E U; Wainwright, Mark; Perera, Sumeth W; Castellanos, Felix; Kroeger, Benjamin; Gandy, Carina; Leiblich, Aaron; Corrigan, Laura; Hilton, Thomas; Patel, Benjamin; Fan, Shih-Jung; Hamdy, Freddie; Goberdhan, Deborah C I; Wilson, Clive

2016-10-01

Regulated secretion by glands and neurons involves release of signalling molecules and enzymes selectively concentrated in dense-core granules (DCGs). Although we understand how many secretagogues stimulate DCG release, how DCG biogenesis is then accelerated to replenish the DCG pool remains poorly characterised. Here we demonstrate that each prostate-like secondary cell (SC) in the paired adult Drosophila melanogaster male accessory glands contains approximately ten large DCGs, which are loaded with the Bone Morphogenetic Protein (BMP) ligand Decapentaplegic (Dpp). These DCGs can be marked in living tissue by a glycophosphatidylinositol (GPI) lipid-anchored form of GFP. In virgin males, BMP signalling is sporadically activated by constitutive DCG secretion. Upon mating, approximately four DCGs are typically released immediately, increasing BMP signalling, primarily via an autocrine mechanism. Using inducible knockdown specifically in adult SCs, we show that secretion requires the Soluble NSF Attachment Protein, SNAP24. Furthermore, mating-dependent BMP signalling not only promotes cell growth, but is also necessary to accelerate biogenesis of new DCGs, restoring DCG number within 24 h. Our analysis therefore reveals an autocrine BMP-mediated feedback mechanism for matching DCG release to replenishment as secretion rates fluctuate, and might explain why in other disease-relevant systems, like pancreatic β-cells, BMP signalling is also implicated in the control of secretion.

Regulation of Dense-Core Granule Replenishment by Autocrine BMP Signalling in Drosophila Secondary Cells

PubMed Central

Redhai, Siamak; Hellberg, Josephine E. E. U.; Wainwright, Mark; Perera, Sumeth W.; Castellanos, Felix; Kroeger, Benjamin; Gandy, Carina; Leiblich, Aaron; Corrigan, Laura; Hilton, Thomas; Patel, Benjamin; Fan, Shih-Jung; Hamdy, Freddie; Goberdhan, Deborah C. I.

2016-01-01

Regulated secretion by glands and neurons involves release of signalling molecules and enzymes selectively concentrated in dense-core granules (DCGs). Although we understand how many secretagogues stimulate DCG release, how DCG biogenesis is then accelerated to replenish the DCG pool remains poorly characterised. Here we demonstrate that each prostate-like secondary cell (SC) in the paired adult Drosophila melanogaster male accessory glands contains approximately ten large DCGs, which are loaded with the Bone Morphogenetic Protein (BMP) ligand Decapentaplegic (Dpp). These DCGs can be marked in living tissue by a glycophosphatidylinositol (GPI) lipid-anchored form of GFP. In virgin males, BMP signalling is sporadically activated by constitutive DCG secretion. Upon mating, approximately four DCGs are typically released immediately, increasing BMP signalling, primarily via an autocrine mechanism. Using inducible knockdown specifically in adult SCs, we show that secretion requires the Soluble NSF Attachment Protein, SNAP24. Furthermore, mating-dependent BMP signalling not only promotes cell growth, but is also necessary to accelerate biogenesis of new DCGs, restoring DCG number within 24 h. Our analysis therefore reveals an autocrine BMP-mediated feedback mechanism for matching DCG release to replenishment as secretion rates fluctuate, and might explain why in other disease-relevant systems, like pancreatic β-cells, BMP signalling is also implicated in the control of secretion. PMID:27727275

Liquid metal cold trap

DOEpatents

Hundal, Rolv

1976-01-01

A cold trap assembly for removing impurities from a liquid metal being provided with a hole between the incoming impure liquid metal and purified outgoing liquid metal which acts as a continuous bleed means and thus prevents the accumulation of cover gases within the cold trap assembly.

Superamphiphobic Silicon-Nanowire-Embedded Microsystem and In-Contact Flow Performance of Gas and Liquid Streams.

PubMed

Ko, Dong-Hyeon; Ren, Wurong; Kim, Jin-Oh; Wang, Jun; Wang, Hao; Sharma, Siddharth; Faustini, Marco; Kim, Dong-Pyo

2016-01-26

Gas and liquid streams are invariably separated either by a solid wall or by a membrane for heat or mass transfer between the gas and liquid streams. Without the separating wall, the gas phase is present as bubbles in liquid or, in a microsystem, as gas plugs between slugs of liquid. Continuous and direct contact between the two moving streams of gas and liquid is quite an efficient way of achieving heat or mass transfer between the two phases. Here, we report a silicon nanowire built-in microsystem in which a liquid stream flows in contact with an underlying gas stream. The upper liquid stream does not penetrate into the lower gas stream due to the superamphiphobic nature of the silicon nanowires built into the bottom wall, thereby preserving the integrity of continuous gas and liquid streams, although they are flowing in contact. Due to the superamphiphobic nature of silicon nanowires, the microsystem provides the best possible interfacial mass transfer known to date between flowing gas and liquid phases, which can achieve excellent chemical performance in two-phase organic syntheses.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jewitt, David; Li Jing, E-mail: jewitt@ucla.ed, E-mail: jli@igpp.ucla.ed

The asteroid (3200) Phaethon is widely recognized as the parent of the Geminid meteoroid stream. However, it has never shown evidence for ongoing mass loss or for any form of comet-like activity that would indicate the continued replenishment of the stream. Following an alert by Battams and Watson, we used NASA's STEREO-A spacecraft to image Phaethon near perihelion, in the period UT 2009 June 17-22, when the heliocentric distance was near 0.14 AU. The resulting photometry shows an unexpected brightening, by a factor of two, starting UT 2009 June 20.2 {+-} 0.2, which we interpret as an impulsive release ofmore » dust particles from Phaethon. If the density is near 2500 kg m{sup -3}, then the emitted dust particles must have a combined mass of {approx}2.5 x 10{sup 8} a{sub 1} kg, where a{sub 1} is the particle radius in millimeters. Assuming a{sub 1} = 1, this is approximately 10{sup -4} of the Geminid stream mass and to replenish the stream in steady state within its estimated {approx}10{sup 3} yr lifetime would require {approx}10 events like the one observed, per orbit. Alternatively, ongoing mass loss may be unrelated to the event which produced the Phaethon-Geminid complex. An impact origin of the dust is highly unlikely. Phaethon is too hot for water ice to survive, rendering the possibility that dust is ejected through gas drag from sublimated ice unlikely. Instead, we suggest that Phaethon is essentially a rock comet, in which the small perihelion distance leads both to the production of dust (through thermal fracture and decomposition cracking of hydrated minerals) and to its ejection into interplanetary space (through radiation pressure sweeping and other effects).« less

Distant and Regional Atmospheric Circulation Influences Governing Integrated Water Vapor Transport and the Occurrence of Extreme Precipitation Events

NASA Astrophysics Data System (ADS)

Bosart, L. F.; Papin, P. P.; Bentley, A. M.

2017-12-01

This presentation will show how the evolution of the large-scale and regional-scale atmospheric circulation contributes to the occurrence of extreme precipitation events (EPEs). An EPE requires that tropospheric moisture flux convergence (MFC) and the associated removal of hydrometeors be balanced by moisture replenishment via integrated (water) vapor transport (IVT) to continuously replenish condensed moisture. Moisture source regions may be distant or regional. Distant moisture sources may require the interaction of lower- and upper-level jet streams with a pre-existing mobile atmospheric disturbance to produce sufficient lift to condense moisture. Pre-existing regional moisture sources may require frontal lifting the presence of MFC to condense moisture. In cases of long-range IVT, such as moisture from a western North Pacific typhoon being drawn poleward along an atmospheric river (AR) toward the west coast of North America, moisture may be transported 1000s of kilometers along a low-level jet before a combination of dynamic and orographic lift results in an EPE. Alternatively, in the case of a typical summer warm and humid air mass over the continental United States, unused moisture may exist for several days in this air mass before sufficient MFC associated with a thermally direct mesoscale frontal circulation can concentrate and condense the moisture. In this case, there may be no long-range IVT via ARs. Instead, the atmospheric circulations may evolve to produce sustained MFC associated with mesoscale frontal circulations, especially in the presence of complex terrain, to produce an EPE. During this presentation, examples of EPEs associated with long-range IVT and distant MFC versus EPEs associated with regional MFC and mesoscale frontal circulations will be illustrated.

Popham Beach, Maine: An example of engineering activity that saved beach property without harming the beach

NASA Astrophysics Data System (ADS)

Kelley, Joseph T.

2013-10-01

Beach and property erosion on coasts is a widespread and chronic problem. Historical approaches to this issue, including seawalls and sand replenishment, are often inappropriate or too expensive. In Maine, seawalls were banned in 1983 and replenishment is too costly to employ. Replacement of storm-damaged buildings is also not allowed, and a precedent case on Popham Beach, Maine required that the owner remove an unpermitted building from a site where an earlier structure was damaged. When the most popular park in Maine, Popham Beach State Park, experienced inlet associated erosion that threatened park infrastructure (a bathhouse), temporary measures were all that the law allowed. Because it was clear that the inlet channel causing the erosion would eventually change course, the state opted to erect a temporary seawall with fallen trees at the site. This may or may not have slowed the erosion temporarily, but reassured the public that "something was being done". Once a storm cut a new tidal inlet channel and closed off the old one, tidal water still entered the former channel and continued to threaten the bathhouse. To ultimately save the property, beach scraping was employed. Sand was scraped from the lower beach to construct a sand berm that deflected the tidal current away from the endangered property. This action created enough time for natural processes to drive the remains of the former spit onto the beach and widen it significantly. Whereas many examples of engineering practices exist that endanger instead of saving beaches, this example is one of an appropriate engineering effort to rescue unwisely located beach-front property.

Simulation of oil bioremediation in a tidally influenced beach: Spatiotemporal evolution of nutrient and dissolved oxygen

NASA Astrophysics Data System (ADS)

Geng, Xiaolong; Pan, Zhong; Boufadel, Michel C.; Ozgokmen, Tamay; Lee, Kenneth; Zhao, Lin

2016-04-01

Numerical experiments of oil bioremediation of tidally influenced beach were simulated using the model BIOMARUN. Nutrient and dissolved oxygen were assumed present in a solution applied on the exposed beach face, and the concentration of these amendments was tracked throughout the beach for up to 6 months. It was found that, in comparison to natural attenuation, bioremediation increased the removal efficiency by 76% and 65% for alkanes and aromatics, respectively. Increasing the nutrient concentration in the applied solution did not always enhance biodegradation as oxygen became limiting even when the beach was originally oxygen-rich. Therefore, replenishment of oxygen to oil-contaminated zone was also essential. Stimulation of oil biodegradation was more evident in the upper and midintertidal zone of the beach, and less in the lower intertidal zone. This was due to reduced nutrient and oxygen replenishment, as very little of the amendment solution reached that zone. It was found that under continual application, most of the oil biodegraded within 2 months, while it persisted for 6 months under natural conditions. While the difference in duration suggests minimal long-term effects, there are situations where the beach would need to be cleaned for major ecological functions, such as temporary nesting or feeding for migratory birds. Biochemical retention time map (BRTM) showed that the duration of solution application was dependent upon the stimulated oil biodegradation rate. By contrast, the application rate of the amendment solution was dependent upon the subsurface extent of the oil-contaminated zone. Delivery of nutrient and oxygen into coastal beach involved complex interaction among amendment solution, groundwater, and seawater. Therefore, approaches that ignore the hydrodynamics due to tide are unlikely to provide the optimal solutions for shoreline bioremediation.

Connectivity of a large embayment and coastal fishery: spawning aggregations in one bay source local and broad-scale fishery replenishment.

PubMed

Hamer, P A; Acevedo, S; Jenkins, G P; Newman, A

2011-04-01

Ichthyoplankton sampling and otolith chemistry were used to determine the importance of transient spawning aggregations of snapper Chrysophrys auratus (Sparidae) in a large embayment, Port Phillip Bay (PPB), Australia, as a source of local and broad-scale fishery replenishment. Ichthyoplankton sampling across five spawning seasons within PPB, across the narrow entrance to the bay and in adjacent coastal waters, indicated that although spawning may occur in coastal waters, the spawning aggregations within the bay were the primary source of larval recruitment to the bay. Otolith chemical signatures previously characterized for 0+ year C. auratus of two cohorts (2000 and 2001) were used as the baseline signatures to quantify the contribution that fish derived from reproduction in PPB make to fishery replenishment. Sampling of these cohorts over a 5 year period at various widely dispersed fishery regions, combined with maximum likelihood analyses of the chemistry of the 0+ year otolith portions of these older fish, indicated that C. auratus of 1 to 3+ years of age displayed both local residency and broad-scale emigration from PPB to populate coastal waters and an adjacent bay (Western Port). While the PPB fishery was consistently dominated (>70%) by locally derived fish irrespective of cohort or age, the contribution of fish that had originated from PPB to distant populations increased with age. At 4 to 5+ years of age, when C. auratus mature and fully recruit to the fishery, populations of both cohorts across the entire central and western Victorian fishery, including two major embayments and c. 800 km of coastal waters, were dominated (>70%) by fish that had originated from the spawning aggregations and nursery habitat within PPB. Dependence of this broadly dispersed fishery on replenishment from heavily targeted spawning aggregations within one embayment has significant implications for management and monitoring programmes. © 2011 The Authors. Journal of Fish Biology © 2011 The Fisheries Society of the British Isles.

Interrupted infusion of echocardiographic contrast as a basis for accurate measurement of myocardial perfusion: ex vivo validation and analysis procedures.

PubMed

Toledo, Eran; Collins, Keith A; Williams, Ursula; Lammertin, Georgeanne; Bolotin, Gil; Raman, Jai; Lang, Roberto M; Mor-Avi, Victor

2005-12-01

Echocardiographic quantification of myocardial perfusion is based on analysis of contrast replenishment after destructive high-energy ultrasound impulses (flash-echo). This technique is limited by nonuniform microbubble destruction and the dependency on exponential fitting of a small number of noisy time points. We hypothesized that brief interruptions of contrast infusion (ICI) would result in uniform contrast clearance followed by slow replenishment and, thus, would allow analysis from multiple data points without exponential fitting. Electrocardiographic-triggered images were acquired in 14 isolated rabbit hearts (Langendorff) at 3 levels of coronary flow (baseline, 50%, and 15%) during contrast infusion (Definity) with flash-echo and with a 20-second infusion interruption. Myocardial videointensity was measured over time from flash-echo sequences, from which characteristic constant beta was calculated using an exponential fit. Peak contrast inflow rate was calculated from ICI data using analysis of local time derivatives. Computer simulations were used to investigate the effects of noise on the accuracy of peak contrast inflow rate and beta calculations. ICI resulted in uniform contrast clearance and baseline replenishment times of 15 to 25 cardiac cycles. Calculated peak contrast inflow rate followed the changes in coronary flow in all hearts at both levels of reduced flow (P < .05) and had a low intermeasurement variability of 7 +/- 6%. With flash-echo, contrast clearance was less uniform and baseline replenishment times were only 4 to 6 cardiac cycles. beta Decreased significantly only at 15% flow, and had intermeasurement variability of 42 +/- 33%. Computer simulations showed that measurement errors in both perfusion indices increased with noise, but beta had larger errors at higher rates of contrast inflow. ICI provides the basis for accurate and reproducible quantification of myocardial perfusion using fast and robust numeric analysis, and may constitute an alternative to the currently used techniques.

Juggling carbon: allocation patterns of a dominant tree in a fire-prone savanna.

PubMed

Schutz, Alexander Ernest Noel; Bond, William J; Cramer, Michael D

2009-05-01

In frequently burnt mesic savannas, trees can get trapped into a cycle of surviving fire-induced stem death (i.e. topkill) by resprouting, only to be topkilled again a year or two later. The ability of savanna saplings to resprout repeatedly after fire is a key component of recent models of tree-grass coexistence in savannas. This study investigated the carbon allocation and biomass partitioning patterns that enable a dominant savanna tree, Acacia karroo, to survive frequent and repeated topkill. Root starch depletion and replenishment, foliage recovery and photosynthesis of burnt and unburnt plants were compared over the first year after a burn. The concentration of starch in the roots of the burnt plants (0.08 +/- 0.01 g g(-1)) was half that of the unburnt plant (0.16 +/- 0.01 g g(-1)) at the end of the first growing season after topkill. However, root starch reserves of the burnt plants were replenished over the dry season and matched that of unburnt plants within 1 year after topkill. The leaf area of resprouting plants recovered to match that of unburnt plants within 4-5 months after topkill. Shoot growth of resprouting plants was restricted to the first few months of the wet season, whereas photosynthetic rates remained high into the dry season, allowing replenishment of root starch reserves. (14)C labeling showed that reserves were initially utilized for shoot growth after topkill. The rapid foliage recovery and the replenishment of reserves within a single year after topkill implies that A. karroo is well adapted to survive recurrent topkill and is poised to take advantage of unusually long fire-free intervals to grow into adults. This paper provides some of the first empirical evidence to explain how savanna trees in frequently burnt savannas are able to withstand frequent burning as juveniles and survive to become adults.

Population connectivity and the effectiveness of marine protected areas to protect vulnerable, exploited and endemic coral reef fishes at an endemic hotspot

NASA Astrophysics Data System (ADS)

van der Meer, M. H.; Berumen, M. L.; Hobbs, J.-P. A.; van Herwerden, L.

2015-06-01

Marine protected areas (MPAs) aim to mitigate anthropogenic impacts by conserving biodiversity and preventing overfishing. The effectiveness of MPAs depends on population connectivity patterns between protected and non-protected areas. Remote islands are endemism hotspots for coral reef fishes and provide rare examples of coral reefs with limited fishing pressure. This study explored population genetic connectivity across a network of protected and non-protected areas for the endemic wrasse, Coris bulbifrons, which is listed as "vulnerable" by the IUCN due to its small, decreasing geographic range and declining abundance. Mitochondrial DNA (mtDNA) and microsatellite DNA (msatDNA) markers were used to estimate historic and contemporary gene flow to determine the level of population self-replenishment and to measure genetic and genotypic diversity among all four locations in the species range (south-west Pacific Ocean)—Middleton Reef (MR), Elizabeth Reef (ER), Lord Howe Island (LHI) and Norfolk Island (NI). MPAs exist at MR and LHI and are limited or non-existent at ER and NI, respectively. There was no obvious differentiation in mtDNA among locations, however, msatDNA revealed differentiation between the most peripheral (NI) and all remaining locations (MR, ER and LHI). Despite high mtDNA connectivity ( M = 259-1,144), msatDNA connectivity was limited ( M = 3-9) with high self-replenishment (68-93 %) at all locations. NI is the least connected and heavily reliant on self-replenishment, and the absence of MPAs at NI needs to be rectified to ensure the persistence of endemic species at this location. Other endemic fishes exhibit similar patterns of high self-replenishment across the four locations, indicating that a single spatial management approach consisting of a MPA network protecting part of each location could provide reasonable protection for these species. Thus, the existing network of MPAs at this endemic hotspot appears adequate at some locations, but not at all.

Replenishment of RANTES mRNA expression in activated eosinophils fromatopic asthmatics

PubMed Central

Velazquez, J R; Lacy, P; Moqbel, R

2000-01-01

Eosinophils have been shown to express the gene encoding regulated upon activation, normal T‐cell expressed and secreted (RANTES), a potent eosinophilotactic chemokine. RANTES protein expression in eosinophils has previously been shown to be up‐regulated by a number of agonists, including complement‐dependent factors (C3b/iC3b) and interferon‐γ (IFN‐γ). We hypothesized that gene expression of RANTES is regulated in these cells by eosinophil‐specific agonists. We analysed RANTES mRNA expression by reverse‐transcription polymerase chain reaction (RT‐PCR) in human peripheral blood eosinophils obtained from mild atopic asthmatics following stimulation over time. In resting eosinophils, a low level of RANTES mRNA was found to be constitutively expressed in all the atopic donors tested in this study (n = 6). Following stimulation with C3b/iC3b (serum‐coated surfaces), eosinophils released measurable levels of RANTES, while sustained transcript expression was detected for up to 24 hr of stimulation. In contrast, IFN‐γ (5 ng/ml) transiently and significantly (P < 0·05, n = 3) depleted relative amounts of RANTES PCR product (compared with β2‐microglobulin) after 1–4 hr of stimulation. RANTES transcript was again detectable after 24 hr of IFN‐γ incubation, suggesting that the pool of RANTES mRNA had been replenished. Other eosinophil‐active cytokines, interleukin‐3 (IL‐3), IL‐4, IL‐5 and granulocyte–macrophage colony‐stimulating factor, did not appear to modulate RANTES mRNA expression after 1 hr of incubation. The effect of IFN‐γ on RANTES mRNA was reversed by cycloheximide, suggesting that IFN‐γ may act by increasing the rate of translation of RANTES mRNA. These findings indicate that IFN‐γ may induce a rapid and transient effect on the translation and replenishment of RANTES mRNA in eosinophils. This novel observation supports the notion that eosinophils have the potential to replenish their stored and released bioactive proteins. PMID:10792507

Scales of magmatic replenishment and differentiation on an intermediate spreading mid-ocean ridge segment: Endeavour, Juan de Fuca Ridge

NASA Astrophysics Data System (ADS)

Dreyer, B. M.; Gill, J.; Clague, D. A.

2016-12-01

The aggregate chemistry of mid-ocean ridge (MOR) basalts cannot be produced by fractional crystallization alone. Recent modeling suggests that repeated magmatic replenishment is required (O'Neill and Jenner, 2012; Coogan and O'Hara, 2015; Shorttle, 2015). Does this inference hold when considering recent advancements in characterizing geological/volcanological context, geochemical variability, and temporal parameters on the scale of individual lava units (Rubin et al., 2009)? We evaluate the scales of magmatic replenishment through examination of compositionally diverse lavas from the Endeavour segment of the Juan de Fuca (JdF) MOR interpreted as comagmatic or coeruptive based on robust geological (Clague et al., 2014), geochemical (Gill et al., 2016), and geochronological (Jamieson et al., 2013; Clague et al., 2014) evidence. This approach is similar to that used for historical MOR eruptions (Rubin et al., 2001). We identified 15 "chemomagmatic" units that are spatially proximate and chemically relatable and separable that collectively represent eruptions since 11ka. Some units may be single lava flows. Other units appear to have erupted batches intermittently over hundreds to thousands of years during which chemically dissimilar lava also erupted. Melt evolution was modeled using MELTS for units with reasonably broad major element variations. Fractional crystallization models can adequately reproduce most of the major and incompatible trace element behavior observed within each unit. Consistent differences in trace element ratios between units argue against intermixing. Thus, magmatic batches typically lie within analytical resolution of fractional crystallizing systems, notwithstanding growing evidence that magmatic systems are repeatedly replenished at the segment scale. Melting and mixing of heterogeneous mantle sources are responsible for the overall compositional diversity at Endeavour. Chemomagmatic units, in contrast, reflect smaller scale processing of magma after exiting the melt column during ascent through the crust. Age and spatial relationships among the chemomagmatic units reflect fluctuations in productivity and composition during assembly of primitive mantle melts and the geometry of networked magma-hosting reservoirs.

Financial and materiel management.

PubMed

Willock, M; Motley, C

1998-01-01

Hospitals have to purchase new technology, update equipment, and replenish supplies continually to meet the needs of patients and the medical and nursing staff in a sound financial way. Thus, inventories must be maintained accurately and adequately with proper controls. Awareness of the cost of capital and operational supplies is essential to meeting budget allocations. With or without centralized buying, the MM department has the expertise to assist every department in purchasing to meet its needs and in setting and resetting inventory levels for its supplies. Explanations and formulas for handling capital equipment and regular supplies and some formats have been presented to facilitate the process. Because OR items are both expensive and numerous and OR storage space the most costly space in the hospital, physicians and nurse managers must understand the financial processes and inventory management and educate their staffs in these matters.

First application of supported ionic liquid phase (SILP) catalysis for continuous methanol carbonylation.

PubMed

Riisager, Anders; Jørgensen, Betina; Wasserscheid, Peter; Fehrmann, Rasmus

2006-03-07

A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)2I2]-[BMIM]I-SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation.

49 CFR 192.165 - Compressor stations: Liquid removal.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Compressor stations: Liquid removal. 192.165 Section 192.165 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE:...

49 CFR 192.165 - Compressor stations: Liquid removal.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Compressor stations: Liquid removal. 192.165 Section 192.165 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE:...

49 CFR 192.165 - Compressor stations: Liquid removal.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Compressor stations: Liquid removal. 192.165 Section 192.165 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE:...

49 CFR 192.165 - Compressor stations: Liquid removal.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Compressor stations: Liquid removal. 192.165 Section 192.165 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE:...

49 CFR 192.165 - Compressor stations: Liquid removal.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Compressor stations: Liquid removal. 192.165 Section 192.165 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE:...

12 CFR 239.62 - Liquidation accounts.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 4 2012-01-01 2012-01-01 false Liquidation accounts. 239.62 Section 239.62 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Conversions from Mutual to Stock Form § 239.62...

12 CFR 239.62 - Liquidation accounts.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 4 2014-01-01 2014-01-01 false Liquidation accounts. 239.62 Section 239.62 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Conversions From Mutual to Stock Form § 239.62...

12 CFR 239.62 - Liquidation accounts.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 4 2013-01-01 2013-01-01 false Liquidation accounts. 239.62 Section 239.62 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Conversions From Mutual to Stock Form § 239.62...

7 CFR 1779.81 - Liquidation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE... lender will notify the Agency in writing within 10 days after its decision to liquidate, which regulatory...) Liquidation plan. The lender will (within 30 days after a decision to liquidate) submit to the Agency, in...

Portable Plating System

NASA Technical Reports Server (NTRS)

Flores, R.

1984-01-01

Plating system mounted on portable cart includes 30-gallon (23.5 liter) electrolyte tank, filler pump, heaters, replenishing anodes, plating rectifiers and tank rectifier to continously remove contaminants.

Highly Productive and Enantioselective Enzyme Catalysis under Continuous Supported Liquid-Liquid Conditions Using a Hybrid Monolithic Bioreactor.

PubMed

Sandig, Bernhard; Buchmeiser, Michael R

2016-10-20

Enzyme-containing ionic liquids (ILs) were immobilized in cellulose-2.5-acetate microbeads particles embedded in a porous monolithic polyurethane matrix. This bioreactor was used under continuous liquid-liquid conditions by dissolving the substrates in a nonpolar organic phase immiscible with the ILs, thereby creating a biphasic system. Lipases (candida antarctica lipase B, CALB, candida rugosa lipase, CRL) were used to catalyze the enantioselective transesterification of racemic (R,S)-1-phenylethanol with vinyl butyrate and vinyl acetate, the esterification of (+/-)-2-isopropyl-5-methylcyclohexanol with propionic anhydride and the amidation of (R,S)-1-phenylethylamine with ethyl methoxyacetate. With this unique setup, very high productivities, that is, turnover numbers (TONs) up to 5.1×10 6 and space-time yields (STYs) up to 28 g product L -1  h -1 , exceeding the corresponding values for batch-type reactions by a factor of 3100 and 40, respectively, were achieved while maintaining or even enhancing enantioselectivity compared to batch reactions via kinetic resolution. To our best knowledge, this is the first continuously operated bioreactor using supported liquid-liquid conditions that shows these features in the synthesis of chiral esters and amides. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

49 CFR 195.4 - Compatibility necessary for transportation of hazardous liquids or carbon dioxide.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Compatibility necessary for transportation of hazardous liquids or carbon dioxide. 195.4 Section 195.4 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY...

49 CFR 195.4 - Compatibility necessary for transportation of hazardous liquids or carbon dioxide.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Compatibility necessary for transportation of hazardous liquids or carbon dioxide. 195.4 Section 195.4 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY...

49 CFR 195.4 - Compatibility necessary for transportation of hazardous liquids or carbon dioxide.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Compatibility necessary for transportation of hazardous liquids or carbon dioxide. 195.4 Section 195.4 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY...

49 CFR 179.102-1 - Carbon dioxide, refrigerated liquid.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Carbon dioxide, refrigerated liquid. 179.102-1 Section 179.102-1 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car...

CONTINUOUS MICRO-SORTING OF COMPLEX WASTE PLASTICS PARTICLEMIXTURES VIA LIQUID-FLUIDIZED BED CLASSIFICATION (LFBC) FOR WASTE MINIMIZATIONAND RECYCLING

EPA Science Inventory

A fundamental investigation is proposed to provide a technical basis for the development of a novel, liquid-fluidized bed classification (LFBC) technology for the continuous separation of complex waste plastic mixtures for in-process recycling and waste minimization. Although ...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2013 CFR

2013-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2010 CFR

2010-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2011 CFR

2011-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2014 CFR

2014-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

40 CFR Table 12 to Subpart G of... - Monitoring Requirements for Treatment Processes

Code of Federal Regulations, 2012 CFR

2012-07-01

... Appropriate methods as specified in § 63.143 and as approved by permitting authority. 2. Steam stripper (i... recorder. (ii) Wastewater feed mass flow rate; and Continuously Liquid flow meter installed at stripper... operating temperature Continuously (A) Liquid temperature monitoring device installed at stripper influent...

12 CFR 239.9 - Conversion or liquidation of mutual holding companies.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 4 2013-01-01 2013-01-01 false Conversion or liquidation of mutual holding companies. 239.9 Section 239.9 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Mutual Holding...

12 CFR 239.9 - Conversion or liquidation of mutual holding companies.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 4 2012-01-01 2012-01-01 false Conversion or liquidation of mutual holding companies. 239.9 Section 239.9 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Mutual Holding...

12 CFR 239.9 - Conversion or liquidation of mutual holding companies.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 4 2014-01-01 2014-01-01 false Conversion or liquidation of mutual holding companies. 239.9 Section 239.9 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) MUTUAL HOLDING COMPANIES (REGULATION MM) Mutual Holding...

40 CFR 98.381 - Reporting threshold.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 21 2011-07-01 2011-07-01 false Reporting threshold. 98.381 Section 98.381 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.381 Reporting threshold. Any supplier of coal-to-liquid products who...

40 CFR 98.381 - Reporting threshold.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 21 2014-07-01 2014-07-01 false Reporting threshold. 98.381 Section 98.381 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.381 Reporting threshold. Any supplier of coal-to-liquid products who...

40 CFR 98.381 - Reporting threshold.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 22 2013-07-01 2013-07-01 false Reporting threshold. 98.381 Section 98.381 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.381 Reporting threshold. Any supplier of coal-to-liquid products who...

46 CFR 154.1760 - Liquid ammonia.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Liquid ammonia. 154.1760 Section 154.1760 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR....1760 Liquid ammonia. The master shall ensure that no person sprays liquid ammonia into a cargo tank...

46 CFR 154.1760 - Liquid ammonia.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Liquid ammonia. 154.1760 Section 154.1760 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR....1760 Liquid ammonia. The master shall ensure that no person sprays liquid ammonia into a cargo tank...

46 CFR 154.1760 - Liquid ammonia.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Liquid ammonia. 154.1760 Section 154.1760 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR....1760 Liquid ammonia. The master shall ensure that no person sprays liquid ammonia into a cargo tank...

46 CFR 154.1760 - Liquid ammonia.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Liquid ammonia. 154.1760 Section 154.1760 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR....1760 Liquid ammonia. The master shall ensure that no person sprays liquid ammonia into a cargo tank...

46 CFR 154.1760 - Liquid ammonia.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Liquid ammonia. 154.1760 Section 154.1760 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR....1760 Liquid ammonia. The master shall ensure that no person sprays liquid ammonia into a cargo tank...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

A note on `a replenishment policy for items with price-dependent demand, time-proportional deterioration and no shortages'

NASA Astrophysics Data System (ADS)

Shah, Nita H.; Soni, Hardik N.; Gupta, Jyoti

2014-08-01

In a recent paper, Begum et al. (2012, International Journal of Systems Science, 43, 903-910) established pricing and replenishment policy for an inventory system with price-sensitive demand rate, time-proportional deterioration rate which follows three parameters, Weibull distribution and no shortages. In their model formulation, it is observed that the retailer's stock level reaches zero before the deterioration occurs. Consequently, the model resulted in traditional inventory model with price sensitive demand rate and no shortages. Hence, the main purpose of this note is to modify and present complete model formulation for Begum et al. (2012). The proposed model is validated by a numerical example and the sensitivity analysis of parameters is carried out.

An Inventory Model for Special Display Goods with Seasonal Demand

NASA Astrophysics Data System (ADS)

Kawakatsu, Hidefumi

2010-10-01

The present study discusses the retailer's optimal replenishment policy for seasonal products. The demand rate of seasonal merchandise such as clothes, sporting goods, children's toys and electrical home appearances tends to decrease with time after reaching its maximum value. In this study, we focus on "Special Display Goods", which are heaped up in end displays or special areas at retail stores. They are sold at a fast velocity when their quantity displayed is large, but are sold at a low velocity if the quantity becomes small. We develop the model with a finite time horizon (selling period) to determine the optimal replenishment policy, which maximizes the retailer's total profit. Numerical examples are presented to illustrate the theoretical underpinnings of the proposed model.

Disposable penis and its replenishment in a simultaneous hermaphrodite

PubMed Central

Sekizawa, Ayami; Seki, Satoko; Tokuzato, Masakazu; Shiga, Sakiko; Nakashima, Yasuhiro

2013-01-01

Although it is often thought that sexual selection is weaker in simultaneous hermaphrodites than in gonochorists, some simultaneous hermaphrodites exhibit bizarre mating behaviour. In the simultaneously hermaphroditic nudibranch Chromodoris reticulata, we found a peculiar mating behaviour, wherein the nudibranch autotomized its penis after each copulation and was able to copulate again within 24 h. To have sufficient length to be replenished for three copulations, the penis is compressed and spiralled internally. No other animal is known to repeatedly copulate using such ‘disposable penes’. Entangled sperm masses were observed on the outer surface of the autotomized penis, which is equipped with many backward-pointed spines. There is a possibility that the nudibranch removes sperm already stored in a mating partner's sperm storage organ(s). PMID:23407499

Heat and mass exchanger

DOEpatents

Lowenstein, Andrew; Sibilia, Marc J.; Miller, Jeffrey A.; Tonon, Thomas

2007-09-18

A mass and heat exchanger includes at least one first substrate with a surface for supporting a continuous flow of a liquid thereon that either absorbs, desorbs, evaporates or condenses one or more gaseous species from or to a surrounding gas; and at least one second substrate operatively associated with the first substrate. The second substrate includes a surface for supporting the continuous flow of the liquid thereon and is adapted to carry a heat exchange fluid therethrough, wherein heat transfer occurs between the liquid and the heat exchange fluid.

Heat and mass exchanger

DOEpatents

Lowenstein, Andrew [Princeton, NJ; Sibilia, Marc J [Princeton, NJ; Miller, Jeffrey A [Hopewell, NJ; Tonon, Thomas [Princeton, NJ

2011-06-28

A mass and heat exchanger includes at least one first substrate with a surface for supporting a continuous flow of a liquid thereon that either absorbs, desorbs, evaporates or condenses one or more gaseous species from or to a surrounding gas; and at least one second substrate operatively associated with the first substrate. The second substrate includes a surface for supporting the continuous flow of the liquid thereon and is adapted to carry a heat exchange fluid therethrough, wherein heat transfer occurs between the liquid and the heat exchange fluid.

Mushy magma processes in the Tuolumne intrusive complex, Sierra Nevada, California

NASA Astrophysics Data System (ADS)

Memeti, V.; Paterson, S. R.

2012-12-01

Debates continue on the nature of volcanic-plutonic connections and the mechanisms of derivation of large volcanic eruptions, which require large volumes of magma to be readily available within a short period of time. Our focus to understand these magma plumbing systems has been to study the nature of their mid-to upper crustal sections, such as the 1,000 km2, 95-85 Ma old Tuolumne intrusive complex in the Sierra Nevada, California, USA. The Tuolumne intrusive complex is a great example where the magma mush model nicely explains observations derived from several datasets. These data suggest that a magma mush body was present and may have been quite extensive especially at times when the Tuolumne intrusive complex was undergoing waxing periods of magmatism (increased magma input), which alternated with waning periods of magmatism (decreased magma addition) and thus a smaller mush body, essentially mimicking in style periodic flare-ups and lulls at the arc scale. During waxing stages, magma erosion and mixing were the dominant processes, whereas waning stages allowed mush domains to continue to undergo fractional crystallization creating additional compositional variations. Over time, the imprint left behind by previous waxing and waning stages was partly overprinted, but individual crystals successfully recorded the compositions of these earlier magmas. Waxing periods in the Tuolumne intrusive complex during which large magma mush bodies formed are supported by the following evidence: 1) Hybrid units and gradational contacts are commonly present between major Tuolumne units. 2) CA-TIMS U/Pb zircon geochronology data demonstrate that antecrystic zircon recycling took place unidirectional from the oldest, marginal unit toward the younger, interior parts of the intrusion, where increasing zircon age spread encompasses the entire age range of the Tuolumne. 3) The younger, interior units also show an increasing scatter and complexity in geochemical element and isotope whole rock data. 4) Single mineral geochemistry suggests that this increased heterogeneity in the interior of the complex is likely caused by the presence of mixed mineral populations that acquired their compositional zoning in magmas different than the one they most recently crystallized in. 5) Mixed mineral populations have also been found in places of local magma mixing (e.g., tubes and troughs), and 6) oscillatory trace element zoning in K-feldspar phenocrysts most likely represents magma replenishment. All of these phenomena suggest a fairly dynamic environment of magma replenishment, magmatic erosion and extensive mixing at the locus of chamber growth. Magma replenishment subsided after episodic flare-ups and the magma mush dominantly underwent fractional crystallization and magmatic fabric formation during waning stages, when it was capable of preserving the evidence at map to crystal scale, lacking any later overprint by mixing. Fractionation related evidence is apparent in the presence of 1) map to outcrop scale leucogranite lenses and dikes in all major Tuolumne units (including the Johnson Peak granite itself), 2) the concentric compositional zonation of magmatic lobes (e.g., southern Half Dome lobe), 3) local crystal accumulations and widespread schlieren, and 4) fractionation related single mineral element zoning.

In-situ continuous water monitoring system

DOEpatents

Thompson, Cyril V.; Wise, Marcus B.

1998-01-01

An in-situ continuous liquid monitoring system for continuously analyzing volatile components contained in a water source comprises: a carrier gas supply, an extraction container and a mass spectrometer. The carrier gas supply continuously supplies the carrier gas to the extraction container and is mixed with a water sample that is continuously drawn into the extraction container by the flow of carrier gas into the liquid directing device. The carrier gas continuously extracts the volatile components out of the water sample. The water sample is returned to the water source after the volatile components are extracted from it. The extracted volatile components and the carrier gas are delivered continuously to the mass spectrometer and the volatile components are continuously analyzed by the mass spectrometer.

In-situ continuous water monitoring system

DOEpatents

Thompson, C.V.; Wise, M.B.

1998-03-31

An in-situ continuous liquid monitoring system for continuously analyzing volatile components contained in a water source comprises: a carrier gas supply, an extraction container and a mass spectrometer. The carrier gas supply continuously supplies the carrier gas to the extraction container and is mixed with a water sample that is continuously drawn into the extraction container by the flow of carrier gas into the liquid directing device. The carrier gas continuously extracts the volatile components out of the water sample. The water sample is returned to the water source after the volatile components are extracted from it. The extracted volatile components and the carrier gas are delivered continuously to the mass spectrometer and the volatile components are continuously analyzed by the mass spectrometer. 2 figs.

49 CFR 195.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... Petroleum means crude oil, condensate, natural gasoline, natural gas liquids, and liquefied petroleum gas... crude oil, unfinished oils, natural gas liquids, blend stocks and other miscellaneous hydrocarbon... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... representative thereof. Petroleum means crude oil, condensate, natural gasoline, natural gas liquids, and... distilling and processing of crude oil, unfinished oils, natural gas liquids, blend stocks and other... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... representative thereof. Petroleum means crude oil, condensate, natural gasoline, natural gas liquids, and... distilling and processing of crude oil, unfinished oils, natural gas liquids, blend stocks and other... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... Petroleum means crude oil, condensate, natural gasoline, natural gas liquids, and liquefied petroleum gas... crude oil, unfinished oils, natural gas liquids, blend stocks and other miscellaneous hydrocarbon... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... Petroleum means crude oil, condensate, natural gasoline, natural gas liquids, and liquefied petroleum gas... crude oil, unfinished oils, natural gas liquids, blend stocks and other miscellaneous hydrocarbon... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

26 CFR 1.332-2 - Requirements for nonrecognition of gain or loss.

Code of Federal Regulations, 2010 CFR

2010-04-01

.... 1.332-2 Section 1.332-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Corporate Liquidations § 1.332-2 Requirements for... its stock in accordance with a plan of liquidation, or (2) one of a series of distributions in...

40 CFR Table A-5 to Subpart A of... - Supplier Category List for § 98.2(a)(4)

Code of Federal Regulations, 2011 CFR

2011-07-01

... liquids suppliers (subpart NN): (A) All fractionators. (B) Local natural gas distribution companies that... (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING General Provision Pt. 98, Subpt. A... a Applicable in 2010 and Future Years Coal-to-liquids suppliers (subpart LL): (A) All producers of...

Spray-On Foam Insulations for Launch Vehicle Cryogenic Tanks

NASA Technical Reports Server (NTRS)

Fesmire, J. E.; Cofman, B. E.; Menghelli, B. J.; Heckle, K. W.

2011-01-01

Spray-on foam insulation (SOFI) has been developed for use on the cryogenic tanks of space launch vehicles beginning in the 1960s with the Apollo program. The use of SOFI was further developed for the Space Shuttle program. The External Tank (ET) of the Space Shuttle, consisting of a forward liquid oxygen tank in line with an aft liquid hydrogen tank, requires thermal insulation over its outer surface to prevent ice formation and avoid in-flight damage to the ceramic tile thermal protection system on the adjacent Orbiter. The insulation also provides system control and stability with throughout the lengthy process of cooldown, loading, and replenishing the tank. There are two main types of SOFI used on the ET: acreage (with the rind) and closeout (machined surface). The thermal performance of the seemingly simple SOFI system is a complex of many variables starting with the large temperature difference of from 200 to 260 K through the typical 25-mm thickness. Environmental factors include air temperature and humidity, wind speed, solar exposure, and aging or weathering history. Additional factors include manufacturing details, launch processing operations, and number of cryogenic thermal cycles. The study of the cryogenic thermal performance of SOFI under large temperature differentials is the subject of this article. The amount of moisture taken into the foam during the cold soak phase, termed Cryogenic Moisture Uptake, must also be considered. The heat leakage rates through these foams were measured under representative conditions using laboratory standard liquid nitrogen boiloff apparatus. Test articles included baseline, aged, and weathered specimens. Testing was performed over the entire pressure range from high vacuum to ambient pressure. Values for apparent thermal conductivity and heat flux were calculated and compared with prior data. As the prior data of record was obtained for small temperature differentials on non-weathered foams, analysis of the different methods is provided. Recent advancements and applications of SOFI systems on future launch vehicles and spacecraft are also addressed.

Reactor for making uniform capsules

NASA Technical Reports Server (NTRS)

Wang, Taylor G. (Inventor); Anikumar, Amrutur V. (Inventor); Lacik, Igor (Inventor)

1999-01-01

The present invention provides a novel reactor for making capsules with uniform membrane. The reactor includes a source for providing a continuous flow of a first liquid through the reactor; a source for delivering a steady stream of drops of a second liquid to the entrance of the reactor; a main tube portion having at least one loop, and an exit opening, where the exit opening is at a height substantially equal to the entrance. In addition, a method for using the novel reactor is provided. This method involves providing a continuous stream of a first liquid; introducing uniformly-sized drops of the second liquid into the stream of the first liquid; allowing the drops to react in the stream for a pre-determined period of time; and collecting the capsules.

49 CFR 179.400 - General specification applicable to cryogenic liquid tank car tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... liquid tank car tanks. 179.400 Section 179.400 Transportation Other Regulations Relating to... (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400 General specification applicable to cryogenic liquid tank car...

49 CFR 179.400 - General specification applicable to cryogenic liquid tank car tanks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... liquid tank car tanks. 179.400 Section 179.400 Transportation Other Regulations Relating to... (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400 General specification applicable to cryogenic liquid tank car...

49 CFR 179.400 - General specification applicable to cryogenic liquid tank car tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... liquid tank car tanks. 179.400 Section 179.400 Transportation Other Regulations Relating to... (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400 General specification applicable to cryogenic liquid tank car...

49 CFR Appendix B to Part 195 - Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines

Code of Federal Regulations, 2014 CFR

2014-10-01

...) (Propane, butane, Natural Gas Liquid (NGL), ammonia) Highly toxic (Benzene, high Hydrogen Sulfide content... Hazardous Liquid and Carbon Dioxide Pipelines B Appendix B to Part 195 Transportation Other Regulations... OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Pt. 195...

49 CFR Appendix B to Part 195 - Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines

Code of Federal Regulations, 2012 CFR

2012-10-01

...) (Propane, butane, Natural Gas Liquid (NGL), ammonia) Highly toxic (Benzene, high Hydrogen Sulfide content... Hazardous Liquid and Carbon Dioxide Pipelines B Appendix B to Part 195 Transportation Other Regulations... OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Pt. 195...

49 CFR Appendix B to Part 195 - Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines

Code of Federal Regulations, 2011 CFR

2011-10-01

...) (Propane, butane, Natural Gas Liquid (NGL), ammonia) Highly toxic (Benzene, high Hydrogen Sulfide content... Hazardous Liquid and Carbon Dioxide Pipelines B Appendix B to Part 195 Transportation Other Regulations... OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Pt. 195...

49 CFR Appendix B to Part 195 - Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines

Code of Federal Regulations, 2013 CFR

2013-10-01

...) (Propane, butane, Natural Gas Liquid (NGL), ammonia) Highly toxic (Benzene, high Hydrogen Sulfide content... Hazardous Liquid and Carbon Dioxide Pipelines B Appendix B to Part 195 Transportation Other Regulations... OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Pt. 195...

49 CFR Appendix B to Part 195 - Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines

Code of Federal Regulations, 2010 CFR

2010-10-01

...) (Propane, butane, Natural Gas Liquid (NGL), ammonia) Highly toxic (Benzene, high Hydrogen Sulfide content... Hazardous Liquid and Carbon Dioxide Pipelines B Appendix B to Part 195 Transportation Other Regulations... OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Pt. 195...

Carbon footprint assessment of Western Australian Groundwater Recycling Scheme

NASA Astrophysics Data System (ADS)

Simms, Andrew; Hamilton, Stacey; Biswas, Wahidul K.

2017-04-01

This research has determined the carbon footprint or the carbon dioxide equivalent (CO2 eq) of potable water production from a groundwater recycling scheme, consisting of the Beenyup wastewater treatment plant, the Beenyup groundwater replenishment trial plant and the Wanneroo groundwater treatment plant in Western Australia, using a life cycle assessment approach. It was found that the scheme produces 1300 tonnes of CO2 eq per gigalitre (GL) of water produced, which is 933 tonnes of CO2 eq higher than the desalination plant at Binningup in Western Australia powered by 100% renewable energy generated electricity. A Monte Carlo Simulation uncertainty analysis calculated a Coefficient of Variation value of 5.4%, thus confirming the accuracy of the simulation. Electricity input accounts for 83% of the carbon dioxide equivalent produced during the production of potable water. The chosen mitigation strategy was to consider the use of renewable energy to generate electricity for carbon intensive groundwater replenishment trial plant. Depending on the local situation, a maximum of 93% and a minimum of 21% greenhouse gas saving from electricity use can be attained at groundwater replenishment trial plant by replacing grid electricity with renewable electricity. In addition, the consideration of vibrational separation (V-Sep) that helps reduce wastes generation and chemical use resulted in a 4.03 tonne of CO2 eq saving per GL of water produced by the plant.

Carbon footprint assessment of Western Australian Groundwater Recycling Scheme.

PubMed

Simms, Andrew; Hamilton, Stacey; Biswas, Wahidul K

2017-04-01

This research has determined the carbon footprint or the carbon dioxide equivalent (CO 2 eq) of potable water production from a groundwater recycling scheme, consisting of the Beenyup wastewater treatment plant, the Beenyup groundwater replenishment trial plant and the Wanneroo groundwater treatment plant in Western Australia, using a life cycle assessment approach. It was found that the scheme produces 1300 tonnes of CO 2 eq per gigalitre (GL) of water produced, which is 933 tonnes of CO 2 eq higher than the desalination plant at Binningup in Western Australia powered by 100% renewable energy generated electricity. A Monte Carlo Simulation uncertainty analysis calculated a Coefficient of Variation value of 5.4%, thus confirming the accuracy of the simulation. Electricity input accounts for 83% of the carbon dioxide equivalent produced during the production of potable water. The chosen mitigation strategy was to consider the use of renewable energy to generate electricity for carbon intensive groundwater replenishment trial plant. Depending on the local situation, a maximum of 93% and a minimum of 21% greenhouse gas saving from electricity use can be attained at groundwater replenishment trial plant by replacing grid electricity with renewable electricity. In addition, the consideration of vibrational separation (V-Sep) that helps reduce wastes generation and chemical use resulted in a 4.03 tonne of CO 2 eq saving per GL of water produced by the plant.

Groundwater rejuvenation in parts of India influenced by water-policy change implementation.

PubMed

Bhanja, Soumendra N; Mukherjee, Abhijit; Rodell, Matthew; Wada, Yoshihide; Chattopadhyay, Siddhartha; Velicogna, Isabella; Pangaluru, Kishore; Famiglietti, James S

2017-08-07

The dwindling groundwater resource of India, supporting almost one fifth of the global population and also the largest groundwater user, has been of great concern in recent years. However, in contrary to the well documented Indian groundwater depletion due to rapid and unmanaged groundwater withdrawal, here for the first time, we report regional-scale groundwater storage (GWS) replenishment through long-term (1996-2014, using more than 19000 observation locations) in situ and decadal (2003-2014) satellite-based groundwater storage measurements in western and southern parts of India. In parts of western and southern India, in situ GWS (GWS obs ) has been decreasing at the rate of -5.81 ± 0.38 km 3 /year (in 1996-2001) and -0.92 ± 0.12 km 3 /year (in 1996-2002), and reversed to replenish at the rate of 2.04 ± 0.20 km 3 /year (in 2002-2014) and 0.76 ± 0.08 km 3 /year (in 2003-2014), respectively. Here, using statistical analyses and simulation results of groundwater management policy change effect on groundwater storage in western and southern India, we show that paradigm shift in Indian groundwater withdrawal and management policies for sustainable water utilization appear to have started replenishing the aquifers in western and southern parts of India.

Real-time monitoring of methanol concentration using a shear horizontal surface acoustic wave sensor for direct methanol fuel cell without reference liquid measurement

NASA Astrophysics Data System (ADS)

Tada, Kyosuke; Nozawa, Takuya; Kondoh, Jun

2017-07-01

In recent years, there has been an increasing demand for sensors that continuously measure liquid concentrations and detect abnormalities in liquid environments. In this study, a shear horizontal surface acoustic wave (SH-SAW) sensor is applied for the continuous monitoring of liquid concentrations. As the SH-SAW sensor functions using the relative measurement method, it normally needs a reference at each measurement. However, if the sensor is installed in a liquid flow cell, it is difficult to measure a reference liquid. Therefore, it is important to establish an estimation method for liquid concentrations using the SH-SAW sensor without requiring a reference measurement. In this study, the SH-SAW sensor is installed in a direct methanol fuel cell to monitor the methanol concentration. The estimated concentration is compared with a conventional density meter. Moreover, the effect of formic acid is examined. When the fuel temperature is higher than 70 °C, it is necessary to consider the influence of liquid conductivity. Here, an estimation method for these cases is also proposed.

The design of an irradiator for the continuous processing of liquid latex

NASA Astrophysics Data System (ADS)

Reuter, O.; Langley, R.; Zn, Wan Manshol Bin W.

1998-06-01

This paper presents anew design concept for a gamma irradiation plant for the continuous processing of pumpable liquids. Typical applications of such a plant include ∗ the irradiation vulcanisation of natural latex rubber ∗ disinfection of municipal sewage sludge for agricultural use ∗ sterilisation of liquids in the pharmaceutical and cosmetics industries ∗ industrial processing of bulk liquids The authors describe the design and operation of the latex irradiator now operating on a small production scale in Malaysia and proposed developments. The design allows irradiation processing to be carried out under an inert or other gaseous environment. State-of-the-art computer control system ensures the fully automatic processing operation needed by industrial computers.

Layerless fabrication with continuous liquid interface production.

PubMed

Janusziewicz, Rima; Tumbleston, John R; Quintanilla, Adam L; Mecham, Sue J; DeSimone, Joseph M

2016-10-18

Despite the increasing popularity of 3D printing, also known as additive manufacturing (AM), the technique has not developed beyond the realm of rapid prototyping. This confinement of the field can be attributed to the inherent flaws of layer-by-layer printing and, in particular, anisotropic mechanical properties that depend on print direction, visible by the staircasing surface finish effect. Continuous liquid interface production (CLIP) is an alternative approach to AM that capitalizes on the fundamental principle of oxygen-inhibited photopolymerization to generate a continual liquid interface of uncured resin between the growing part and the exposure window. This interface eliminates the necessity of an iterative layer-by-layer process, allowing for continuous production. Herein we report the advantages of continuous production, specifically the fabrication of layerless parts. These advantages enable the fabrication of large overhangs without the use of supports, reduction of the staircasing effect without compromising fabrication time, and isotropic mechanical properties. Combined, these advantages result in multiple indicators of layerless and monolithic fabrication using CLIP technology.

Layerless fabrication with continuous liquid interface production

PubMed Central

Janusziewicz, Rima; Tumbleston, John R.; Quintanilla, Adam L.; Mecham, Sue J.; DeSimone, Joseph M.

2016-01-01

Despite the increasing popularity of 3D printing, also known as additive manufacturing (AM), the technique has not developed beyond the realm of rapid prototyping. This confinement of the field can be attributed to the inherent flaws of layer-by-layer printing and, in particular, anisotropic mechanical properties that depend on print direction, visible by the staircasing surface finish effect. Continuous liquid interface production (CLIP) is an alternative approach to AM that capitalizes on the fundamental principle of oxygen-inhibited photopolymerization to generate a continual liquid interface of uncured resin between the growing part and the exposure window. This interface eliminates the necessity of an iterative layer-by-layer process, allowing for continuous production. Herein we report the advantages of continuous production, specifically the fabrication of layerless parts. These advantages enable the fabrication of large overhangs without the use of supports, reduction of the staircasing effect without compromising fabrication time, and isotropic mechanical properties. Combined, these advantages result in multiple indicators of layerless and monolithic fabrication using CLIP technology. PMID:27671641

A Microwave Tunable Bandpass Filter for Liquid Crystal Applications

NASA Astrophysics Data System (ADS)

Cao, Weiping; Jiang, Di; Liu, Yupeng; Yang, Yuanwang; Gan, Baichuan

2017-07-01

In this paper, a novel microwave continuously tunable band-pass filter, based on nematic liquid crystals (LCs), is proposed. It uses liquid crystal (LC) as the electro-optic material to mainly realize frequency shift at microwave band by changing the dielectric anisotropy, when applying the bias voltage. According to simulation results, it achieves 840 MHz offset. Comparing to the existing tunable filter, it has many advantages, such as continuously tunable, miniaturization, low processing costs, low tuning voltage, etc. Thus, it has shown great potentials in frequency domain and practical applications in modern communication.

49 CFR 195.424 - Pipe movement.

Code of Federal Regulations, 2012 CFR

2012-10-01

... operating pressure. (b) No operator may move any pipeline containing highly volatile liquids where materials... pressure of the commodity. (c) No operator may move any pipeline containing highly volatile liquids where... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.424 - Pipe movement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... operating pressure. (b) No operator may move any pipeline containing highly volatile liquids where materials... pressure of the commodity. (c) No operator may move any pipeline containing highly volatile liquids where... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.424 - Pipe movement.

Code of Federal Regulations, 2013 CFR

2013-10-01

... operating pressure. (b) No operator may move any pipeline containing highly volatile liquids where materials... pressure of the commodity. (c) No operator may move any pipeline containing highly volatile liquids where... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

49 CFR 195.424 - Pipe movement.

Code of Federal Regulations, 2014 CFR

2014-10-01

... operating pressure. (b) No operator may move any pipeline containing highly volatile liquids where materials... pressure of the commodity. (c) No operator may move any pipeline containing highly volatile liquids where... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY...

40 CFR 258.28 - Liquids restrictions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 258.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR MUNICIPAL SOLID WASTE LANDFILLS Operating Criteria § 258.28 Liquids restrictions. (a) Bulk or... (Paint Filter Liquids Test), included in “Test Methods for Evaluating Solid Waste, Physical/Chemical...

40 CFR 258.28 - Liquids restrictions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 258.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES CRITERIA FOR MUNICIPAL SOLID WASTE LANDFILLS Operating Criteria § 258.28 Liquids restrictions. (a) Bulk or... (Paint Filter Liquids Test), included in “Test Methods for Evaluating Solid Waste, Physical/Chemical...

40 CFR Table 24 to Subpart Uuu of... - Continuous Monitoring Systems for Inorganic HAP Emissions From Catalytic Reforming Units

Code of Federal Regulations, 2012 CFR

2012-07-01

... scrubbing liquid) flow rate entering the scrubber during coke burn-off and catalyst rejuvenation; and... during coke burn-off and catalyst rejuvenation 1; and continuous parameter monitoring system to measure and record the pH or alkalinity of the water (or scrubbing liquid) exiting the scrubber during coke...

40 CFR Table 24 to Subpart Uuu of... - Continuous Monitoring Systems for Inorganic HAP Emissions From Catalytic Reforming Units

Code of Federal Regulations, 2014 CFR

2014-07-01

... scrubbing liquid) flow rate entering the scrubber during coke burn-off and catalyst rejuvenation; and... during coke burn-off and catalyst rejuvenation 1; and continuous parameter monitoring system to measure and record the pH or alkalinity of the water (or scrubbing liquid) exiting the scrubber during coke...

40 CFR Table 24 to Subpart Uuu of... - Continuous Monitoring Systems for Inorganic HAP Emissions From Catalytic Reforming Units

Code of Federal Regulations, 2013 CFR

2013-07-01

... scrubbing liquid) flow rate entering the scrubber during coke burn-off and catalyst rejuvenation; and... during coke burn-off and catalyst rejuvenation 1; and continuous parameter monitoring system to measure and record the pH or alkalinity of the water (or scrubbing liquid) exiting the scrubber during coke...

26 CFR 1.312-5 - Special rule for partial liquidations and certain redemptions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 4 2010-04-01 2010-04-01 false Special rule for partial liquidations and certain redemptions. 1.312-5 Section 1.312-5 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Effects on Corporation § 1.312-5 Special rule for...

Electric field-driven, magnetically-stabilized ferro-emulsion phase contactor

DOEpatents

Scott, T.C.

1990-07-17

Methods and systems are disclosed for interfacial surface area contact between a dispersed phase liquid and a continuous phase liquid in counter-current flow for purposes such as solvent extraction. Initial droplets of a dispersed phase liquid material containing ferromagnetic particles functioning as a packing'' are introduced to a counter-current flow of the continuous phase. A high intensity pulsed electric field is applied so as to shatter the initial droplets into a ferromagnetic emulsion comprising many smaller daughter droplets having a greater combined total surface area than that of the initial droplets in contact with the continuous phase material. A magnetic field is applied to control the position of the ferromagnetic emulsion for enhanced coalescence of the daughter droplets into larger reformed droplets. 2 figs.

Electric field-driven, magnetically-stabilized ferro-emulsion phase contactor

DOEpatents

Scott, Timothy C.

1990-01-01

Methods and systems for interfacial surface area contact between a dispersed phase liquid and a continuous phase liquid in counter-current flow for purposes such as solvent extraction. Initial droplets of a dispersed phase liquid material containing ferromagnetic particles functioning as a "packing" are introduced to a counter-current flow of the continuous phase. A high intensity pulsed electric field is applied so as to shatter the initial droplets into a ferromagnetic emulsion comprising many smaller daughter droplets having a greater combined total surface area than that of the initial droplets in contact with the continuous phase material. A magnetic field is applied to control the position of the ferromagnetic emulsion for enhanced coalescence of the daughter droplets into larger reformed droplets.

Mount St. Helens erupts again: activity from September 2004 through March 2005

USGS Publications Warehouse

Major, Jon J.; Scott, William E.; Driedger, Carolyn; Dzurisin, Dan

2005-01-01

Eruptive activity at Mount St. Helens captured the world’s attention in 1980 when the largest historical landslide on Earth and a powerful explosion reshaped the volcano, created its distinctive crater, and dramatically modified the surrounding landscape. Over the next 6 years, episodic extrusions of lava built a large dome in the crater. From 1987 to 2004, Mount St. Helens returned to a period of relative quiet, interrupted by occasional, short-lived seismic swarms that lasted minutes to days, by months-to-yearslong increases in background seismicity that probably reflected replenishment of magma deep underground, and by minor steam explosions as late as 1991. During this period a new glacier grew in the crater and wrapped around and partly buried the lava dome. Although the volcano was relatively quiet, scientists with the U.S. Geological Survey and University of Washington’s Pacific Northwest Seismograph Network continued to closely monitor it for signs of renewed activity.

Secondary emission electron gun using external primaries

DOEpatents

Srinivasan-Rao, Triveni [Shoreham, NY; Ben-Zvi, Ilan [Setauket, NY

2009-10-13

An electron gun for generating an electron beam is provided, which includes a secondary emitter. The secondary emitter includes a non-contaminating negative-electron-affinity (NEA) material and emitting surface. The gun includes an accelerating region which accelerates the secondaries from the emitting surface. The secondaries are emitted in response to a primary beam generated external to the accelerating region. The accelerating region may include a superconducting radio frequency (RF) cavity, and the gun may be operated in a continuous wave (CW) mode. The secondary emitter includes hydrogenated diamond. A uniform electrically conductive layer is superposed on the emitter to replenish the extracted current, preventing charging of the emitter. An encapsulated secondary emission enhanced cathode device, useful in a superconducting RF cavity, includes a housing for maintaining vacuum, a cathode, e.g., a photocathode, and the non-contaminating NEA secondary emitter with the uniform electrically conductive layer superposed thereon.

Secondary emission electron gun using external primaries

DOEpatents

Srinivasan-Rao, Triveni [Shoreham, NY; Ben-Zvi, Ilan [Setauket, NY; Kewisch, Jorg [Wading River, NY; Chang, Xiangyun [Middle Island, NY

2007-06-05

An electron gun for generating an electron beam is provided, which includes a secondary emitter. The secondary emitter includes a non-contaminating negative-electron-affinity (NEA) material and emitting surface. The gun includes an accelerating region which accelerates the secondaries from the emitting surface. The secondaries are emitted in response to a primary beam generated external to the accelerating region. The accelerating region may include a superconducting radio frequency (RF) cavity, and the gun may be operated in a continuous wave (CW) mode. The secondary emitter includes hydrogenated diamond. A uniform electrically conductive layer is superposed on the emitter to replenish the extracted current, preventing charging of the emitter. An encapsulated secondary emission enhanced cathode device, useful in a superconducting RF cavity, includes a housing for maintaining vacuum, a cathode, e.g., a photocathode, and the non-contaminating NEA secondary emitter with the uniform electrically conductive layer superposed thereon.

Habitat selection by marine larvae in changing chemical environments.

PubMed

Lecchini, D; Dixson, D L; Lecellier, G; Roux, N; Frédérich, B; Besson, M; Tanaka, Y; Banaigs, B; Nakamura, Y

2017-01-15

The replenishment and persistence of marine species is contingent on dispersing larvae locating suitable habitat and surviving to a reproductive stage. Pelagic larvae rely on environmental cues to make behavioural decisions with chemical information being important for habitat selection at settlement. We explored the sensory world of crustaceans and fishes focusing on the impact anthropogenic alterations (ocean acidification, red soil, pesticide) have on conspecific chemical signals used by larvae for habitat selection. Crustacean (Stenopus hispidus) and fish (Chromis viridis) larvae recognized their conspecifics via chemical signals under control conditions. In the presence of acidified water, red soil or pesticide, the ability of larvae to chemically recognize conspecific cues was altered. Our study highlights that recruitment potential on coral reefs may decrease due to anthropogenic stressors. If so, populations of fishes and crustaceans will continue their rapid decline; larval recruitment will not replace and sustain the adult populations on degraded reefs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Photophoretic levitation of engineered aerosols for geoengineering

PubMed Central

Keith, David W.

2010-01-01

Aerosols could be injected into the upper atmosphere to engineer the climate by scattering incident sunlight so as to produce a cooling tendency that may mitigate the risks posed by the accumulation of greenhouse gases. Analysis of climate engineering has focused on sulfate aerosols. Here I examine the possibility that engineered nanoparticles could exploit photophoretic forces, enabling more control over particle distribution and lifetime than is possible with sulfates, perhaps allowing climate engineering to be accomplished with fewer side effects. The use of electrostatic or magnetic materials enables a class of photophoretic forces not found in nature. Photophoretic levitation could loft particles above the stratosphere, reducing their capacity to interfere with ozone chemistry; and, by increasing particle lifetimes, it would reduce the need for continual replenishment of the aerosol. Moreover, particles might be engineered to drift poleward enabling albedo modification to be tailored to counter polar warming while minimizing the impact on equatorial climates. PMID:20823254

Photophoretic levitation of engineered aerosols for geoengineering.

PubMed

Keith, David W

2010-09-21

Aerosols could be injected into the upper atmosphere to engineer the climate by scattering incident sunlight so as to produce a cooling tendency that may mitigate the risks posed by the accumulation of greenhouse gases. Analysis of climate engineering has focused on sulfate aerosols. Here I examine the possibility that engineered nanoparticles could exploit photophoretic forces, enabling more control over particle distribution and lifetime than is possible with sulfates, perhaps allowing climate engineering to be accomplished with fewer side effects. The use of electrostatic or magnetic materials enables a class of photophoretic forces not found in nature. Photophoretic levitation could loft particles above the stratosphere, reducing their capacity to interfere with ozone chemistry; and, by increasing particle lifetimes, it would reduce the need for continual replenishment of the aerosol. Moreover, particles might be engineered to drift poleward enabling albedo modification to be tailored to counter polar warming while minimizing the impact on equatorial climates.

Phenological synchrony of bird migration with tree flowering at desert riparian stopover sites

USGS Publications Warehouse

Kellermann, Jherime L.; van Riper, Charles

2015-01-01

Small-bodied songbirds replenish fat reserves during migration at stopover sites where they continually encounter novel and often unpredictable environmental conditions. The ability to select and utilize high quality habitats is critical to survival and fitness. Vegetation phenology is closely linked with emergence of insect prey and may provide valid cues of food availability for stopover habitat selection. Climate change is disrupting phenological synchrony across trophic levels with negative impacts on bird populations. However, whether synchrony or mismatch indicates historic or disrupted systems remains unclear. Many Neotropical migratory songbirds of western North America must cross arid regions where drought conditions related to climate change and human water use are expected to increase. We studied migrant abundance and the diversity (niche breadth) and proportional use of vegetation species as foraging substrates and their synchrony with vegetation flowering during spring migration along the lower Colorado River in the Sonoran Desert of the U.S. and Mexico.

Particles Co-orbital to Janus and to Epimetheus: A Firefly Planetary Ring

NASA Astrophysics Data System (ADS)

Winter, Othon C.; Souza, Alexandre P. S.; Sfair, Rafael; Giuliatti Winter, Silvia M.; Mourão, Daniela C.; Foryta, Dietmar W.

2018-01-01

The Cassini spacecraft found a new and unique ring that shares the trajectory of Janus and Epimetheus, co-orbital satellites of Saturn. Performing image analysis, we found this to be a continuous ring. Its width is between 30% and 50% larger than previously announced. We also verified that the ring behaves like a firefly. It can only be seen from time to time, when Cassini, the ring, and the Sun are arranged in a particular geometric configuration, in very high phase angles. Otherwise, it remains “in the dark,” invisible to Cassini’s cameras. Through numerical simulations, we found a very short lifetime for the ring particles, less than a couple of decades. Consequently, the ring needs to be constantly replenished. Using a model of particle production due to micrometeorites impacts on the surfaces of Janus and Epimetheus, we reproduce the ring, explaining its existence and the “firefly” behavior.

Product demand forecasts using wavelet kernel support vector machine and particle swarm optimization in manufacture system

NASA Astrophysics Data System (ADS)

Wu, Qi

2010-03-01

Demand forecasts play a crucial role in supply chain management. The future demand for a certain product is the basis for the respective replenishment systems. Aiming at demand series with small samples, seasonal character, nonlinearity, randomicity and fuzziness, the existing support vector kernel does not approach the random curve of the sales time series in the space (quadratic continuous integral space). In this paper, we present a hybrid intelligent system combining the wavelet kernel support vector machine and particle swarm optimization for demand forecasting. The results of application in car sale series forecasting show that the forecasting approach based on the hybrid PSOWv-SVM model is effective and feasible, the comparison between the method proposed in this paper and other ones is also given, which proves that this method is, for the discussed example, better than hybrid PSOv-SVM and other traditional methods.

A stochastic inventory management model for a dual sourcing supply chain with disruptions

NASA Astrophysics Data System (ADS)

Iakovou, Eleftherios; Vlachos, Dimitrios; Xanthopoulos, Anastasios

2010-03-01

As companies continue to globalise their operations and outsource significant portion of their value chain activities, they often end up relying heavily on order replenishments from distant suppliers. The explosion in long-distance sourcing is exposing supply chains and shareholder value at ever increasing operational and disruption risks. It is well established, both in academia and in real-world business environments, that resource flexibility is an effective method for hedging against supply chain disruption risks. In this contextual framework, we propose a single period stochastic inventory decision-making model that could be employed for capturing the trade-off between inventory policies and disruption risks for an unreliable dual sourcing supply network for both the capacitated and uncapacitated cases. Through the developed model, we obtain some important managerial insights and evaluate the merit of contingency strategies in managing uncertain supply chains.

Preparation of pentacene thin film deposited using organic material auto-feeding system for the fabrication of organic thin film transistor.

PubMed

Kim, Young Baek; Choi, Bum Ho; Lim, Yong Hwan; Yoo, Ha Na; Lee, Jong Ho; Kim, Jin Hyeok

2011-02-01

In this study, pentacene organic thin film was prepared using newly developed organic material auto-feeding system integrated with linear cell and characterized. The newly developed organic material auto-feeding system consists of 4 major parts: reservoir, micro auto-feeder, vaporizer, and linear cell. The deposition of organic thin film could be precisely controlled by adjusting feeding rate, main tube size, position and size of nozzle. 10 nm thick pentacene thin film prepared on glass substrate exhibited high uniformity of 3.46% which is higher than that of conventional evaporation method using point cell. The continuous deposition without replenishment of organic material can be performed over 144 hours with regulated deposition control. The grain size of pentacene film which affect to mobility of OTFT, was controlled as a function of the temperature.

Is cell aging caused by respiration-dependent injury to the mitochondrial genome

NASA Technical Reports Server (NTRS)

Fleming, J. E.; Yengoyan, L. S.; Miquel, J.; Cottrell, S. F.; Economos, A. C.

1982-01-01

Though intrinsic mitochondrial aging has been considered before as a possible cause of cellular senescence, the mechanisms of such mitochondrial aging have remained obscure. In this article, the hypothesis of free-radical-induced inhibition of mitochondrial replenishment in fixed postmitotic cells is expanded. It is maintained that the respiration-dependent production of superoxide and hydroxyl radicals may not be fully counteracted, leading to a continuous production of lipoperoxides and malonaldehyde in actively respiring mitochondria. These compounds, in turn, can easily react with the mitochondrial DNA which is in close spatial relationship with the inner mitochondrial membrane, producing an injury that the mitochondria may be unable to counteract because of their apparent lack of adequate repair mechanisms. Mitochondrial division may thus be inhibited leading to age-related reduction of mitochondrial numbers, a deficit in energy production with a concomitant decrease in protein synthesis, deterioration of physiological performance, and, therefore, of organismic performance.

Holocene depletion and active recharge of the Kalahari groundwaters — A review and an indicative model

NASA Astrophysics Data System (ADS)

De Vries, J. J.

1984-02-01

A paramount question in the evaluation of groundwater resources in the Kalahari semi-desert is whether there is any active infiltration of present-day rainfall to the deep aquifers. Previous investigations with isotope analyses gave evidence of recent recharge but no unanimity about the distribution of this process has been reached until now. The present study investigates whether the regional hydraulic gradient means a modern replenishment, or whether the slope of the piezometric surface should be explained as a residual feature resulting from head decay since the last pluvial period. It is concluded that the hydraulic gradient is most probably of a residual nature, and the replenishment has been less than 0.5 mm yr. -1 during at least the last 4000 yr. or so.

High liquid yield process for retorting various organic materials including oil shale

DOEpatents

Coburn, Thomas T.

1990-01-01

This invention is a continuous retorting process for various high molecular weight organic materials, including oil shale, that yields an enhanced output of liquid product. The organic material, mineral matter, and an acidic catalyst, that appreciably adsorbs alkenes on surface sites at prescribed temperatures, are mixed and introduced into a pyrolyzer. A circulating stream of olefin enriched pyrolysis gas is continuously swept through the organic material and catalyst, whereupon, as the result of pyrolysis, the enhanced liquid product output is provided. Mixed spent organic material, mineral matter, and cool catalyst are continuously withdrawn from the pyrolyzer. Combustion of the spent organic material and mineral matter serves to reheat the catalyst. Olefin depleted pyrolysis gas, from the pyrolyzer, is enriched in olefins and recycled into the pyrolyzer. The reheated acidic catalyst is separated from the mineral matter and again mixed with fresh organic material, to maintain the continuously cyclic process.

A high liquid yield process for retorting various organic materials including oil shale

DOEpatents

Coburn, T.T.

1988-07-26

This invention is a continuous retorting process for various high molecular weight organic materials, including oil shale, that yields an enhanced output of liquid product. The organic material, mineral matter, and an acidic catalyst, that appreciably adsorbs alkenes on surface sites at prescribed temperatures, are mixed and introduced into a pyrolyzer. A circulating stream of olefin enriched pyrolysis gas is continuously swept through the organic material and catalyst, whereupon, as the result of pyrolysis, the enhanced liquid product output is provided. Mixed spent organic material, mineral matter, and cool catalyst are continuously withdrawn from the pyrolyzer. Combustion of the spent organic material and mineral matter serves to reheat the catalyst. Olefin depleted pyrolysis gas, from the pyrolyzer, is enriched in olefins and recycled into the pyrolyzer. The reheated acidic catalyst is separated from the mineral matter and again mixed with fresh organic material, to maintain the continuously cyclic process. 2 figs.

REDISTRIBUTOR FOR LIQUID-LIQUID EXTRACTION COLUMNS

DOEpatents

Bradley, J.G.

1957-10-29

An improved baffle plate construction to intimately mix immiscible liquid solvents for solvent extraction processes in a liquid-liquid pulse column is described. To prevent the light and heavy liquids from forming separate continuous homogeneous vertical channels through sections of the column, a baffle having radially placed rectangular louvers with deflection plates opening upon alternate sides of the baffle is placed in the column, normal to the axis. This improvement substantially completely reduces strippiig losses due to poor mixing.

Cost and cost effectiveness of long-lasting insecticide-treated bed nets - a model-based analysis

PubMed Central

2012-01-01

Background The World Health Organization recommends that national malaria programmes universally distribute long-lasting insecticide-treated bed nets (LLINs). LLINs provide effective insecticide protection for at least three years while conventional nets must be retreated every 6-12 months. LLINs may also promise longer physical durability (lifespan), but at a higher unit price. No prospective data currently available is sufficient to calculate the comparative cost effectiveness of different net types. We thus constructed a model to explore the cost effectiveness of LLINs, asking how a longer lifespan affects the relative cost effectiveness of nets, and if, when and why LLINs might be preferred to conventional insecticide-treated nets. An innovation of our model is that we also considered the replenishment need i.e. loss of nets over time. Methods We modelled the choice of net over a 10-year period to facilitate the comparison of nets with different lifespan (and/or price) and replenishment need over time. Our base case represents a large-scale programme which achieves high coverage and usage throughout the population by distributing either LLINs or conventional nets through existing health services, and retreats a large proportion of conventional nets regularly at low cost. We identified the determinants of bed net programme cost effectiveness and parameter values for usage rate, delivery and retreatment cost from the literature. One-way sensitivity analysis was conducted to explicitly compare the differential effect of changing parameters such as price, lifespan, usage and replenishment need. Results If conventional and long-lasting bed nets have the same physical lifespan (3 years), LLINs are more cost effective unless they are priced at more than USD 1.5 above the price of conventional nets. Because a longer lifespan brings delivery cost savings, each one year increase in lifespan can be accompanied by a USD 1 or more increase in price without the cheaper net (of the same type) becoming more cost effective. Distributing replenishment nets each year in addition to the replacement of all nets every 3-4 years increases the number of under-5 deaths averted by 5-14% at a cost of USD 17-25 per additional person protected per annum or USD 1080-1610 per additional under-5 death averted. Conclusions Our results support the World Health Organization recommendation to distribute only LLINs, while giving guidance on the price thresholds above which this recommendation will no longer hold. Programme planners should be willing to pay a premium for nets which have a longer physical lifespan, and if planners are willing to pay USD 1600 per under-5 death averted, investing in replenishment is cost effective. PMID:22475679

7 CFR 762.149 - Liquidation.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Liquidation. 762.149 Section 762.149 Agriculture Regulations of the Department of Agriculture (Continued) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS GUARANTEED FARM LOANS § 762.149 Liquidation. (a) Mediation. When it has been determined...

41 CFR 105-55.014 - Liquidation of collateral.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Management Regulations System (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services Administration 55-COLLECTION OF CLAIMS OWED THE UNITED STATES § 105-55.014 Liquidation of collateral. (a) The General Services Administration (GSA) will liquidate security or collateral through the exercise of a...

17 CFR 75.3 - Prohibition on proprietary trading.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) PROPRIETARY TRADING AND CERTAIN INTERESTS IN AND RELATIONSHIPS WITH COVERED FUNDS Proprietary... of liquidity management in accordance with a documented liquidity management plan of the banking... liquidity management purposes, the amount, types, and risks of these securities that are consistent with...

17 CFR 255.3 - Prohibition on proprietary trading.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) PROPRIETARY TRADING AND CERTAIN INTERESTS IN AND RELATIONSHIPS WITH COVERED FUNDS Proprietary... purpose of liquidity management in accordance with a documented liquidity management plan of the banking... liquidity management purposes, the amount, types, and risks of these securities that are consistent with...

[Correction of hydrodynamic disorders in severe alcohol poisoning in adolescent].

PubMed

Simakov, A A; Ostreĭkov, I F; Sukhodolova, G N; Dolginov, D M

2014-01-01

To improve the results of treatment of children with severe alcohol poisoning as a result of investigation of water sectors of the body. The study included 54 patients aged from 13 to 15 years with a diagnosis of acute severe alcohol poisoning. All patients were divided into three groups. At the initial examination was determined the concentration of alcohol in saliva using Express-test "Alkoskan." Bioimpedance analysis was performed; water sectors of the body were investigated by analyzer of the balance of water sectors ABC-01 "Medass." The study was conducted at the time of admission, after 12, 24 and 48 hours. In severe alcohol poisoning at the time of admission, it was revealed a reduction of the fluid in all studied sectors. The most effective compensation of liquid was observed in groups, where was used combination therapy included intravenous fluids based 4.0 ml/kg/hour. The treatment of severe alcohol poisoning should include fluid resuscitation about 4 ml/kg/hour. This capacity of medical care give the ability to correct adequately the water-sectoral disturbances already in the first 12 hours of hospitalization, and the inclusion to the basic therapy reamberine can contribute more effective replenishment of water sectors.

Urinary metabolic insights into host-gut microbial interactions in healthy and IBD children

PubMed Central

Martin, Francois-Pierre; Su, Ming-Ming; Xie, Guo-Xiang; Guiraud, Seu Ping; Kussmann, Martin; Godin, Jean-Philippe; Jia, Wei; Nydegger, Andreas

2017-01-01

AIM To identify metabolic signatures in urine samples from healthy and inflammatory bowel disease (IBD) children. METHODS We applied liquid chromatography and gas chromatography coupled to targeted mass spectrometry (MS)-based metabolite profiling to identify and quantify bile acids and host-gut microbial metabolites in urine samples collected from 21 pediatric IBD patients monitored three times over one year (baseline, 6 and 12 mo), and 27 age- and gender-matched healthy children. RESULTS urinary metabolic profiles of IBD children differ significantly from healthy controls. Such metabolic differences encompass central energy metabolism, amino acids, bile acids and gut microbial metabolites. In particular, levels of pyroglutamic acid, glutamic acid, glycine and cysteine, were significantly higher in IBD children in the course of the study. This suggests that glutathione cannot be optimally synthesized and replenished. Whilst alterations of the enterohepatic circulation of bile acids in pediatric IBD patients is known, we show here that non-invasive urinary bile acid profiling can assess those altered hepatic and intestinal barrier dysfunctions. CONCLUSION The present study shows how non-invasive sampling of urine followed by targeted MS-based metabonomic analysis can elucidate and monitor the metabolic status of children with different GI health/disease status. PMID:28611517

Differences in surfactant lipids collected from pleural and pulmonary lining fluids.

PubMed

Mills, Paul C; Chen, Yi; Hills, Yvette C; Hills, Brian A

2005-11-01

The type and relative importance of saturated and unsaturated phospholipid components of surfactant within the epithelial lining fluid (ELF) of the inner and outer surfaces of the lung is not known. Seven healthy dogs were anesthetized and a bronchoalveolar lavage (BAL) was performed, immediately followed by a pleural lavage (PL). Lipid was extracted from lavage fluid and then analyzed for saturated, primarily dipalmitoylphosphatidylcholine (DPPC), and unsaturated phosphatidylcholine (PC) species using high-performance liquid chromatography (HPLC) with combined fluorescence and ultraviolet detection. Dilution of ELF in lavage fluids was corrected for using the urea method. DPPC (494.7 +/- 213.9 microg/mL) was the predominant PC present in ELF collected from the alveolar surface. In contrast, significantly higher (p = 0.028) proportions of unsaturated PC species were measured in PL fluid (approximately 105 microg/mL), particularly stearoyl-linoleoyl-phosphatidylcholine (SLPC), which could not be measured in fluid collected from the alveoli, compared to DPPC (2.6 +/- 2.0 microg/mL). This study indicates that unsaturated PC species seem to be more important than saturated species, particularly DPPC, in the pleural cavity, which has implications for surfactant replenishment following pleural disease or thoracic surgery.

Method for continuously recovering metals using a dual zone chemical reactor

DOEpatents

Bronson, Mark C.

1995-01-01

A dual zone chemical reactor continuously processes metal-containing materials while regenerating and circulating a liquid carrier. The starting materials are fed into a first reaction zone of a vessel containing a molten salt carrier. The starting materials react to form a metal product and a by-product that dissolves in the molten salt that flows to a second reaction zone in the reaction vessel. The second reaction zone is partitioned from, but in fluid communication with, the first reaction zone. The liquid carrier continuously circulates along a pathway between the first reaction zone and the second reaction zone. A reactive gas is introduced into the second reaction zone to react with the reaction by-product to generate the molten salt. The metal product, the gaseous waste products, and the excess liquid carrier are removed without interrupting the operation of the reactor. The design of the dual zone reactor can be adapted to combine a plurality of liquid carrier regeneration zones in a multiple dual zone chemical reactor for production scale processing.

The fluid dynamics of a basaltic magma chamber replenished by influx of hot, dense ultrabasic magma

NASA Astrophysics Data System (ADS)

Huppert, Herbert E.; Sparks, R. Stephen J.

1981-09-01

This paper describes a fluid dynamical investigation of the influx of hot, dense ultrabasic magma into a reservoir containing lighter, fractionated basaltic magma. This situation is compared with that which develops when hot salty water is introduced under cold fresh water. Theoretical and empirical models for salt/water systems are adapted to develop a model for magmatic systems. A feature of the model is that the ultrabasic melt does not immediately mix with the basalt, but spreads out over the floor of the chamber, forming an independent layer. A non-turbulent interface forms between this layer and the overlying magma layer across which heat and mass are transferred by the process of molecular diffusion. Both layers convect vigorously as heat is transferred to the upper layer at a rate which greatly exceeds the heat lost to the surrounding country rock. The convection continues until the two layers have almost the same temperature. The compositions of the layers remain distinct due to the low diffusivity of mass compared to heat. The temperatures of the layers as functions of time and their cooling rate depend on their viscosities, their thermal properties, the density difference between the layers and their thicknesses. For a layer of ultrabasic melt (18% MgO) a few tens of metres thick at the base of a basaltic (10% MgO) magma chamber a few kilometres thick, the temperature of the layers will become nearly identical over a period of between a few months and a few years. During this time the turbulent convective velocities in the ultrabasic layer are far larger than the settling velocity of olivines which crystallise within the layer during cooling. Olivines only settle after the two layers have nearly reached thermal equilibrium. At this stage residual basaltic melt segregates as the olivines sediment in the lower layer. Depending on its density, the released basalt can either mix convectively with the overlying basalt layer, or can continue as a separate layer. The model provides an explanation for large-scale cyclic layering in basic and ultrabasic intrusions. The model also suggests reasons for the restriction of erupted basaltic liquids to compositions with MgO<10% and the formation of some quench textures in layered igneous rocks.

Geologic framework influences on the geomorphology of an anthropogenically modified barrier island: Assessment of dune/beach changes at Fire Island, New York

USGS Publications Warehouse

Lentz, E.E.; Hapke, C.J.

2011-01-01

Antecedent geology plays a crucial role in determining the inner-shelf, nearshore, and onshore geomorphology observed in coastal systems. However, the influence of the geologic framework on a system is difficult to extract when evaluating responses to changes due to storms and anthropogenic modifications, and few studies have quantified the potential for these influences in dune/beach environments. This study evaluates topographic change to the dune/beach system at Fire Island, New York over a ten year period (1998-2008) at two sites representing eastern and western reaches of the island where morphology has been shown to vary. The sites are situated along swaths of coast eroding differentially and where the inner shelf geologic framework differs substantially. Fewer large storms occurred in the first half of the study period, compared with the later part of the study period which includes several severe and prolonged extratropical storms. Additionally, a major beach replenishment project was conducted at one of the study sites. Topographic data from LiDAR and RTK GPS surveys are used to construct high-resolution 3D surfaces, which are used to determine volumetric change and to extract 2D alongshore features and profiles for analysis. The study sites help to further characterize morphologic differences between eastern and western reaches of the island. The western site displays higher sand volumes, lower dunes, and a lower gradient profile slope when compared with the eastern site. In addition to these fundamental morphologic differences, the two sites also differ significantly in their response to coastal storms and in the fact that their replenishment histories are different. The replenished areas show reduced vulnerability to storms through minimal volume loss and shoreline accretion that should be considered when evaluating the response of replenished areas to episodic events. We propose that site-specific differences evident throughout the study period can be linked to alongshore variations in the framework geology of the system. Anthropogenic modifications may have intensified differences already inherent in the system. ?? 2010 Elsevier B.V.

Vitamin D in corticosteroid-naïve and corticosteroid-treated Duchenne muscular dystrophy: what dose achieves optimal 25(OH) vitamin D levels?

PubMed

Alshaikh, Nahla; Brunklaus, Andreas; Davis, Tracey; Robb, Stephanie A; Quinlivan, Ros; Munot, Pinki; Sarkozy, Anna; Muntoni, Francesco; Manzur, Adnan Y

2016-10-01

Assessment of the efficacy of vitamin D replenishment and maintenance doses required to attain optimal levels in boys with Duchenne muscular dystrophy (DMD). 25(OH)-vitamin D levels and concurrent vitamin D dosage were collected from retrospective case-note review of boys with DMD at the Dubowitz Neuromuscular Centre. Vitamin D levels were stratified as deficient at <25 nmol/L, insufficient at 25-49 nmol/L, adequate at 50-75 nmol/L and optimal at >75 nmol/L. 617 vitamin D samples were available from 197 boys (range 2-18 years)-69% from individuals on corticosteroids. Vitamin D-naïve boys (154 samples) showed deficiency in 28%, insufficiency in 42%, adequate levels in 24% and optimal levels in 6%. The vitamin D-supplemented group (463 samples) was tested while on different maintenance/replenishment doses. Three-month replenishment of daily 3000 IU (23 samples) or 6000 IU (37 samples) achieved optimal levels in 52% and 84%, respectively. 182 samples taken on 400 IU revealed deficiency in 19 (10%), insufficiency in 84 (47%), adequate levels in 67 (37%) and optimal levels in 11 (6%). 97 samples taken on 800 IU showed deficiency in 2 (2%), insufficiency in 17 (17%), adequate levels in 56 (58%) and optimal levels in 22 (23%). 81 samples were on 1000 IU and 14 samples on 1500 IU, with optimal levels in 35 (43%) and 9 (64%), respectively. No toxic level was seen (highest level 230 nmol/L). The prevalence of vitamin D deficiency and insufficiency in DMD is high. A 2-month replenishment regimen of 6000 IU and maintenance regimen of 1000-1500 IU/day was associated with optimal vitamin D levels. These data have important implications for optimising vitamin D dosing in DMD. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

49 CFR 179.102-1 - Carbon dioxide, refrigerated liquid.

Code of Federal Regulations, 2011 CFR

2011-10-01

... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.102-1 Carbon dioxide, refrigerated liquid. (a) Tank cars used to transport carbon dioxide, refrigerated liquid...

49 CFR 179.102-1 - Carbon dioxide, refrigerated liquid.

Code of Federal Regulations, 2013 CFR

2013-10-01

... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.102-1 Carbon dioxide, refrigerated liquid. (a) Tank cars used to transport carbon dioxide, refrigerated liquid...

49 CFR 179.102-1 - Carbon dioxide, refrigerated liquid.

Code of Federal Regulations, 2014 CFR

2014-10-01

... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Pressure Tank Car Tanks (Classes DOT-105, 109, 112, 114 and 120) § 179.102-1 Carbon dioxide, refrigerated liquid. (a) Tank cars used to transport carbon dioxide, refrigerated liquid...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

Liquid volume monitoring based on ultrasonic sensor and Arduino microcontroller

NASA Astrophysics Data System (ADS)

Husni, M.; Siahaan, D. O.; Ciptaningtyas, H. T.; Studiawan, H.; Aliarham, Y. P.

2016-04-01

Incident of oil leakage and theft in oil tank often happens. To prevent it, the liquid volume insides the tank needs to be monitored continuously. Aim of the study is to calculate the liquid volume inside oil tank on any road condition and send the volume data and location data to the user. This research use some ultrasonic sensors (to monitor the fluid height), Bluetooth modules (to sent data from the sensors to the Arduino microcontroller), Arduino Microcontroller (to calculate the liquid volume), and also GPS/GPRS/GSM Shield module (to get location of vehicle and sent the data to the Server). The experimental results show that the accuracy rate of monitoring liquid volume inside tanker while the vehicle is in the flat road is 99.33% and the one while the vehicle is in the road with elevation angle is 84%. Thus, this system can be used to monitor the tanker position and the liquid volume in any road position continuously via web application to prevent illegal theft.

Enrichment of light hydrocarbon mixture

DOEpatents

Yang, Dali [Los Alamos, NM; Devlin, David [Santa Fe, NM; Barbero, Robert S [Santa Cruz, NM; Carrera, Martin E [Naperville, IL; Colling, Craig W [Warrenville, IL

2011-11-29

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Enrichment of light hydrocarbon mixture

DOEpatents

Yang,; Dali, [Los Alamos, NM; Devlin, David [Santa Fe, NM; Barbero, Robert S [Santa Cruz, NM; Carrera, Martin E [Naperville, IL; Colling, Craig W [Warrenville, IL

2010-08-10

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Accelerated gas-liquid visible light photoredox catalysis with continuous-flow photochemical microreactors.

PubMed

Straathof, Natan J W; Su, Yuanhai; Hessel, Volker; Noël, Timothy

2016-01-01

In this protocol, we describe the construction and use of an operationally simple photochemical microreactor for gas-liquid photoredox catalysis using visible light. The general procedure includes details on how to set up the microreactor appropriately with inlets for gaseous reagents and organic starting materials, and it includes examples of how to use it to achieve continuous-flow preparation of disulfides or trifluoromethylated heterocycles and thiols. The reported photomicroreactors are modular, inexpensive and can be prepared rapidly from commercially available parts within 1 h even by nonspecialists. Interestingly, typical reaction times of gas-liquid visible light photocatalytic reactions performed in microflow are lower (in the minute range) than comparable reactions performed as a batch process (in the hour range). This can be attributed to the improved irradiation efficiency of the reaction mixture and the enhanced gas-liquid mass transfer in the segmented gas-liquid flow regime.

DEVELOPMENT AND VALIDATION OF A MULTIFIELD MODEL OF CHURN-TURBULENT GAS/LIQUID FLOWS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elena A. Tselishcheva; Steven P. Antal; Michael Z. Podowski

The accuracy of numerical predictions for gas/liquid two-phase flows using Computational Multiphase Fluid Dynamics (CMFD) methods strongly depends on the formulation of models governing the interaction between the continuous liquid field and bubbles of different sizes. The purpose of this paper is to develop, test and validate a multifield model of adiabatic gas/liquid flows at intermediate gas concentrations (e.g., churn-turbulent flow regime), in which multiple-size bubbles are divided into a specified number of groups, each representing a prescribed range of sizes. The proposed modeling concept uses transport equations for the continuous liquid field and for each bubble field. The overallmore » model has been implemented in the NPHASE-CMFD computer code. The results of NPHASE-CMFD simulations have been validated against the experimental data from the TOPFLOW test facility. Also, a parametric analysis on the effect of various modeling assumptions has been performed.« less

46 CFR 109.557 - Flammable and combustible liquids: Carriage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Flammable and combustible liquids: Carriage. 109.557 Section 109.557 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.557 Flammable and combustible liquids: Carriage. The master...

46 CFR 109.557 - Flammable and combustible liquids: Carriage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Flammable and combustible liquids: Carriage. 109.557 Section 109.557 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.557 Flammable and combustible liquids: Carriage. The master...

46 CFR 109.557 - Flammable and combustible liquids: Carriage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Flammable and combustible liquids: Carriage. 109.557 Section 109.557 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.557 Flammable and combustible liquids: Carriage. The master...

46 CFR 109.557 - Flammable and combustible liquids: Carriage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Flammable and combustible liquids: Carriage. 109.557 Section 109.557 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.557 Flammable and combustible liquids: Carriage. The master...

46 CFR 109.557 - Flammable and combustible liquids: Carriage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Flammable and combustible liquids: Carriage. 109.557 Section 109.557 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.557 Flammable and combustible liquids: Carriage. The master...

10 CFR 609.15 - Default, demand, payment, and collateral liquidation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Default, demand, payment, and collateral liquidation. 609.15 Section 609.15 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS LOAN GUARANTEES FOR PROJECTS THAT EMPLOY INNOVATIVE TECHNOLOGIES § 609.15 Default, demand, payment, and collateral liquidation...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 417.80 - Applicability; description of the manufacture of liquid soaps subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... manufacture of liquid soaps subcategory. 417.80 Section 417.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Soaps Subcategory § 417.80 Applicability; description of the manufacture of...

40 CFR 98.386 - Data reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.386 Data reporting... measurement standard method or other industry standard practice used. For natural gas liquids, quantity shall... site, report the total annual quantity in metric tons or barrels. For natural gas liquids, quantity...

40 CFR 98.386 - Data reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.386 Data reporting... barrels. For natural gas liquids, quantity shall reflect the individual components of the product. (3) For... quantity in metric tons or barrels. For natural gas liquids, quantity shall reflect the individual...

40 CFR 98.386 - Data reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.386 Data reporting... measurement standard method or other industry standard practice used. For natural gas liquids, quantity shall... site, report the total annual quantity in metric tons or barrels. For natural gas liquids, quantity...

40 CFR 98.386 - Data reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.386 Data reporting... measurement standard method or other industry standard practice used. For natural gas liquids, quantity shall... site, report the total annual quantity in metric tons or barrels. For natural gas liquids, quantity...

40 CFR 98.386 - Data reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Coal-based Liquid Fuels § 98.386 Data reporting... measurement standard method or other industry standard practice used. For natural gas liquids, quantity shall... site, report the total annual quantity in metric tons or barrels. For natural gas liquids, quantity...

Preliminary guidelines and recommendations for the development of material and process specifications for carbon fiber-reinforced liquid resin molded materials.

DOT National Transportation Integrated Search

2007-05-01

This document recommends guidance and criteria for the development of material and process specifications and material acceptance documents for liquid resins and continuous carbon fiber reinforcement materials used in liquid molding processes to manu...

World Bank International Development Association Replenishment Act of 2009

THOMAS, 111th Congress

Sen. Kerry, John F. [D-MA

2009-05-01

Senate - 07/16/2009 Placed on Senate Legislative Calendar under General Orders. Calendar No. 112. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

A Titration Technique for Demonstrating a Magma Replenishment Model.

ERIC Educational Resources Information Center

Hodder, A. P. W.

1983-01-01

Conductiometric titrations can be used to simulate subduction-setting volcanism. Suggestions are made as to the use of this technique in teaching volcanic mechanisms and geochemical indications of tectonic settings. (JN)

Foulant characteristics comparison in recycling cooling water system makeup by municipal reclaimed water and surface water in power plant.

PubMed

Ping, Xu; Jing, Wang; Yajun, Zhang; Jie, Wang; Shuai, Si

2015-01-01

Due to water shortage, municipal reclaimed water rather than surface water was replenished into recycling cooling water system in power plants in some cities in China. In order to understand the effects of the measure on carbon steel corrosion, characteristics of two kinds of foulant produced in different systems were studied in the paper. Differences between municipal reclaimed water and surface water were analyzed firstly. Then, the weight and the morphology of two kinds of foulant were compared. Moreover, other characteristics including the total number of bacteria, sulfate reducing bacteria, iron bacteria, extracellular polymeric substance (EPS), protein (PN), and polysaccharide (PS) in foulant were analyzed. Based on results, it could be concluded that microbial and corrosive risk would be increased when the system replenished by municipal reclaimed water instead of surface water.

Joint pricing, inventory, and preservation decisions for deteriorating items with stochastic demand and promotional efforts

NASA Astrophysics Data System (ADS)

Soni, Hardik N.; Chauhan, Ashaba D.

2018-03-01

This study models a joint pricing, inventory, and preservation decision-making problem for deteriorating items subject to stochastic demand and promotional effort. The generalized price-dependent stochastic demand, time proportional deterioration, and partial backlogging rates are used to model the inventory system. The objective is to find the optimal pricing, replenishment, and preservation technology investment strategies while maximizing the total profit per unit time. Based on the partial backlogging and lost sale cases, we first deduce the criterion for optimal replenishment schedules for any given price and technology investment cost. Second, we show that, respectively, total profit per time unit is concave function of price and preservation technology cost. At the end, some numerical examples and the results of a sensitivity analysis are used to illustrate the features of the proposed model.

Modeling and measurement of vesicle pools at the cone ribbon synapse: changes in release probability are solely responsible for voltage-dependent changes in release

PubMed Central

Thoreson, Wallace B.; Van Hook, Matthew J.; Parmelee, Caitlyn; Curto, Carina

2015-01-01

Post-synaptic responses are a product of quantal amplitude (Q), size of the releasable vesicle pool (N), and release probability (P). Voltage-dependent changes in presynaptic Ca2+ entry alter post-synaptic responses primarily by changing P but have also been shown to influence N. With simultaneous whole cell recordings from cone photoreceptors and horizontal cells in tiger salamander retinal slices, we measured N and P at cone ribbon synapses by using a train of depolarizing pulses to stimulate release and deplete the pool. We developed an analytical model that calculates the total pool size contributing to release under different stimulus conditions by taking into account the prior history of release and empirically-determined properties of replenishment. The model provided a formula that calculates vesicle pool size from measurements of the initial post-synaptic response and limiting rate of release evoked by a train of pulses, the fraction of release sites available for replenishment, and the time constant for replenishment. Results of the model showed that weak and strong depolarizing stimuli evoked release with differing probabilities but the same size vesicle pool. Enhancing intraterminal Ca2+ spread by lowering Ca2+ buffering or applying BayK8644 did not increase PSCs evoked with strong test steps showing there is a fixed upper limit to pool size. Together, these results suggest that light-evoked changes in cone membrane potential alter synaptic release solely by changing release probability. PMID:26541100

Muscle glycogen depletion and subsequent replenishment affect anaerobic capacity of horses.

PubMed

Lacombe, V A; Hinchcliff, K W; Geor, R J; Baskin, C R

2001-10-01

The purpose of this study was to determine the effect of muscle glycogen depletion and subsequent replenishment on anaerobic capacity of horses. In a blinded crossover study, seven fit horses performed glycogen-depleting exercise on two occasions. Horses were infused after glycogen-depleting exercise with either 6 g/kg body wt of glucose as a 13.5% solution in 0.9% NaCl (Glu) or with 0.9% NaCl (Sal) of equivalent volume. Subsequently, horses performed a high-speed exercise test (120% of maximal rate of oxygen consumption) to estimate maximum accumulated oxygen deficit. Replenishment of muscle glycogen was greater (P < 0.05) in Glu [from 24.7 +/- 7.2 (SE) to 116.5 +/- 7 mmol/kg wet wt before and after infusion, respectively] than in Sal (from 23.4 +/- 7.2 to 47.8 +/- 5.7 mmol/kg wet wt before and after infusion, respectively). Run time to fatigue during the high-speed exercise test (97.3 +/- 8.2 and 70.8 +/- 8.3 s, P < 0.05), maximal accumulated oxygen deficit (105.7 +/- 9.3 and 82.4 +/- 10.3 ml O(2) equivalent/kg, P < 0.05), and blood lactate concentration at the end of the high-speed exercise test (11.1 +/- 1.4 and 9.2 +/- 3.7 mmol/l, P < 0.05) were greater for Glu than for Sal, respectively. We concluded that decreased availability of skeletal muscle glycogen stores diminishes anaerobic power generation and capacity for high-intensity exercise in horses.

Comparison through a prospective and randomized study of two replenishment methods at polyvalent hospitalization units with two-bin storage systems

PubMed

Bernal, José Luis; Mera-Flores, Ana María; Baena Lázaro, Pedro Pablo; Sebastián Viana, Tomás

2017-11-27

Two-bin storage systems increase nursing staff satisfaction and decrease inventories, but the implications that logistic staff would determine the needs of replenishment are unknown. This study aimed to evaluate whether entrust to logistics staff this responsibility at the polyvalent hospitalization units with two-bin storage is associated with higher risk of outstanding orders. This was a prospective randomized experiment whit masking. Outstanding orders were considered variable response, those corresponding to assessments of the logistics staff were included in the control group and those corresponding to the nursing staff in the control group. Concordance between observers was analyzed using the Bland-Altman method; the difference between groups, with the U of Mann-Whitney and the cumulative incidence of outstanding orders and their relative risk was calculated. The mean amount requested by the logistic and nursing staff was 29.9 (SD:167.4) and 36 (SD:190) units respectively, the mean difference between observers was 6.11 (SD:128.95) units and no significant differences were found between groups (p = 0.430). The incidence of outstanding orders was 0.64% in the intervention group and 0.15% in the control group; the relative risk, 2.31 (0.83 - 6.48) and the number of cases required for an outstanding order, 516. Outstanding order relative risk is not associated with the category of the staff that identifies the replenishment needs at the polyvalent hospitalization units.

46 CFR 109.575 - Accumulation of liquids on helicopter decks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Accumulation of liquids on helicopter decks. 109.575 Section 109.575 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master...

46 CFR 109.575 - Accumulation of liquids on helicopter decks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Accumulation of liquids on helicopter decks. 109.575 Section 109.575 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master...

46 CFR 109.575 - Accumulation of liquids on helicopter decks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Accumulation of liquids on helicopter decks. 109.575 Section 109.575 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master...

46 CFR 109.575 - Accumulation of liquids on helicopter decks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Accumulation of liquids on helicopter decks. 109.575 Section 109.575 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master...

46 CFR 109.575 - Accumulation of liquids on helicopter decks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Accumulation of liquids on helicopter decks. 109.575 Section 109.575 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.575 Accumulation of liquids on helicopter decks. The master...

Dendrite inhibitor

DOEpatents

Miller, W.E.

1988-06-07

An apparatus for removing dendrites or other crystalline matter from the surface of a liquid in a matter transport process, and an electrolytic cell including such an apparatus. A notch may be provided to allow continuous exposure of the liquid surface, and a bore may be further provided to permit access to the liquid. 2 figs.

21 CFR 880.6970 - Liquid crystal vein locator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Liquid crystal vein locator. 880.6970 Section 880.6970 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... skin by displaying the color changes of heat sensitive liquid crystals (cholesteric esters). (b...

Cavitation in liquid cryogens. 1: Venturi

NASA Technical Reports Server (NTRS)

Hord, J.; Anderson, L. M.; Hall, W. J.

1972-01-01

The results of continuing cavitation studies are reported. The cavitation characteristics of liquid hydrogen and liquid nitrogen flowing in a transparent plastic Venturi are discussed. Thermodynamic data, consisting of pressure and temperature measurements within fully developed hydrogen cavities, are reported. Details concerning test apparatus, test procedure, and data correlation techniques are given.

46 CFR 188.10-17 - Combustible liquid.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Combustible liquid. 188.10-17 Section 188.10-17 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-17 Combustible liquid. This term includes any...

46 CFR 188.10-27 - Flammable liquid.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Flammable liquid. 188.10-27 Section 188.10-27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-27 Flammable liquid. This term includes any...

46 CFR 188.10-27 - Flammable liquid.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Flammable liquid. 188.10-27 Section 188.10-27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-27 Flammable liquid. This term includes any...

46 CFR 188.10-23 - Corrosive liquids.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Corrosive liquids. 188.10-23 Section 188.10-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-23 Corrosive liquids. (a) This term includes...

46 CFR 188.10-17 - Combustible liquid.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Combustible liquid. 188.10-17 Section 188.10-17 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-17 Combustible liquid. This term includes any...

46 CFR 188.10-27 - Flammable liquid.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Flammable liquid. 188.10-27 Section 188.10-27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-27 Flammable liquid. This term includes any...

46 CFR 188.10-27 - Flammable liquid.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Flammable liquid. 188.10-27 Section 188.10-27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-27 Flammable liquid. This term includes any...

46 CFR 188.10-17 - Combustible liquid.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Combustible liquid. 188.10-17 Section 188.10-17 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-17 Combustible liquid. This term includes any...

46 CFR 188.10-23 - Corrosive liquids.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Corrosive liquids. 188.10-23 Section 188.10-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-23 Corrosive liquids. (a) This term includes...

46 CFR 188.10-17 - Combustible liquid.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Combustible liquid. 188.10-17 Section 188.10-17 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-17 Combustible liquid. This term includes any...

46 CFR 188.10-27 - Flammable liquid.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Flammable liquid. 188.10-27 Section 188.10-27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-27 Flammable liquid. This term includes any...

46 CFR 188.10-17 - Combustible liquid.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Combustible liquid. 188.10-17 Section 188.10-17 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Definition of Terms Used in This Subchapter § 188.10-17 Combustible liquid. This term includes any...

21 CFR 880.6970 - Liquid crystal vein locator.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Liquid crystal vein locator. 880.6970 Section 880.6970 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... skin by displaying the color changes of heat sensitive liquid crystals (cholesteric esters). (b...

46 CFR 151.25-1 - Cargo tank.

Code of Federal Regulations, 2014 CFR

2014-10-01

... not react with the cargo. (c) Ventilated (forced). Vapor space above the liquid surface in the tank is... (natural). Vapor space above the liquid surface in the tank is continuously swept with atmospheric air... LIQUID HAZARDOUS MATERIAL CARGOES Environmental Control § 151.25-1 Cargo tank. When carrying certain...

46 CFR 151.25-1 - Cargo tank.

Code of Federal Regulations, 2012 CFR

2012-10-01

... not react with the cargo. (c) Ventilated (forced). Vapor space above the liquid surface in the tank is... (natural). Vapor space above the liquid surface in the tank is continuously swept with atmospheric air... LIQUID HAZARDOUS MATERIAL CARGOES Environmental Control § 151.25-1 Cargo tank. When carrying certain...

46 CFR 151.25-1 - Cargo tank.

Code of Federal Regulations, 2011 CFR

2011-10-01

... not react with the cargo. (c) Ventilated (forced). Vapor space above the liquid surface in the tank is... (natural). Vapor space above the liquid surface in the tank is continuously swept with atmospheric air... LIQUID HAZARDOUS MATERIAL CARGOES Environmental Control § 151.25-1 Cargo tank. When carrying certain...

46 CFR 151.25-1 - Cargo tank.

Code of Federal Regulations, 2013 CFR

2013-10-01

... not react with the cargo. (c) Ventilated (forced). Vapor space above the liquid surface in the tank is... (natural). Vapor space above the liquid surface in the tank is continuously swept with atmospheric air... LIQUID HAZARDOUS MATERIAL CARGOES Environmental Control § 151.25-1 Cargo tank. When carrying certain...

46 CFR 151.25-1 - Cargo tank.

Code of Federal Regulations, 2010 CFR

2010-10-01

... not react with the cargo. (c) Ventilated (forced). Vapor space above the liquid surface in the tank is... (natural). Vapor space above the liquid surface in the tank is continuously swept with atmospheric air... LIQUID HAZARDOUS MATERIAL CARGOES Environmental Control § 151.25-1 Cargo tank. When carrying certain...

Dendrite inhibitor

DOEpatents

Miller, William E.

1989-01-01

An apparatus for removing dendrites or other crystalline matter from the surface of a liquid in a matter transport process, and an electrolytic cell including such an apparatus. A notch may be provided to allow continuous exposure of the liquid surface, and a bore may be further provided to permit access to the liquid.

40 CFR 98.403 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.403... natural gas processing plants from local production, received as a liquid and vaporized for delivery, or... local production, or natural gas that was received as a liquid, vaporized and delivered, and any other...

Deep-crustal seismicity in volcanic regions by fluid-enhanced wallrock embrittlement

NASA Astrophysics Data System (ADS)

Sisson, T. W.; Power, J. A.

2013-12-01

Spatial association of deep long-period (DLP) seismicity with volcanoes [1,2], spectral frequencies resembling shallow events attributed to fluid motions, and temporal associations with some eruptions, prompt the interpretation that DLPs mark the locations of magma, or magma with percolating exsolved vapor, in the mid and lower crust. However, various factors are more consistent with the events taking place in the walls surrounding the hot aseismic cores of deep magmatic systems, due to expelled magmatic fluids elevating pore pressures and reducing wall rock brittle strengths, or possibly in largely solidified peripheral intrusions embrittled by interstitial residual melt. First, although exceptions are known, deep seismic events are typically displaced to one or more sides of the locus of volcanism. Compilation of >1000 mid to deep crustal DLP and volcano tectonic events from the Aleutian arc, plotted as radial distance from the respective volcanic locus vs. depth, shows a minimum of events beneath the volcanic loci, encased in a downward broadening halo of events, typically displaced about 6 km to the sides of the volcanic locus. Lateral offsets of deep events are also well established for volcanoes of the Washington Cascades [3], averaging 7.5×4.5(1σ) km, and for some centers in California [1]. Second, while mafic parental magmas can have high concentrations of H2O (CO2 concentrations are comparatively negligible), H2O is highly soluble at mid to lower crustal pressures and will not exsolve appreciably until advanced crystallization and second boiling. Deep vapor exsolution will proceed gradually, delayed well after replenishment events, due to slow cooling and crystallization in the hot deep crust. Exsolution dominantly at high crystallinities argues against bubbles moving through largely liquid replenishing magmas as a major cause of DLPs. Third, isotherms around the mid to deep crustal portions of magmatic systems will propagate outward with time1/2 due to dominantly conductive heat transfer at those depths. Over the ca. 1-5×105 yr durations of convergent margin volcanoes, characteristic isotherms propagate <10 km (k: 2.25 W/mK); temperature dependent thermal conductivity [4] would reduce these distances. Deep magmatic systems are therefore encased in relatively thin thermal sheaths, outboard of which temperatures drop sharply to near-ambient values, and rock strengths increase accordingly. Collectively, these factors support a scenario wherein magmas crystallize in the roots of volcanic systems, gradually exsolving and releasing vapor, some of which percolates into surrounding wallrocks. Beyond some critical isotherm, plastic rock strength increases sufficiently for fluid enhanced brittle failure when the walls are stressed by magma replenishments or by ordinary tectonic forces. If so, the statistical spatial distribution of DLPs indicates that the hot, active portions of the deep magmatic systems are relatively narrow, commonly <6 km in semi-minor radius. 1. Pitt et al., 2002, Seis Res Lett 73:144-152 2. Power et al., 2004, Jour Volc Geotherm Res 138:243-266 3. Nichols et al., 2011, Jour Volc Geotherm Res 200:116-128 4. Whittington et al., 2009, Nature 458, 319-321

Continuous-flow liquid microjunction surface sampling probe connected on-line with high-performance liquid chromatography/mass spectrometry for spatially resolved analysis of small molecules and proteins.

PubMed

Van Berkel, Gary J; Kertesz, Vilmos

2013-06-30

A continuous-flow liquid microjunction surface sampling probe extracts soluble material from surfaces for direct ionization and detection by mass spectrometry. Demonstrated here is the on-line coupling of such a probe with high-performance liquid chromatography/mass spectrometry (HPLC/MS) enabling extraction, separation and detection of small molecules and proteins from surfaces in a spatially resolved (~0.5 mm diameter spots) manner. A continuous-flow liquid microjunction surface sampling probe was connected to a six-port, two-position valve for extract collection and injection to an HPLC column. A QTRAP® 5500 hybrid triple quadrupole linear ion trap equipped with a Turbo V™ ion source operated in positive electrospray ionization (ESI) mode was used for all experiments. The system operation was tested with the extraction, separation and detection of propranolol and associated metabolites from drug dosed tissues, caffeine from a coffee bean, cocaine from paper currency, and proteins from dried sheep blood spots on paper. Confirmed in the tissue were the parent drug and two different hydroxypropranolol glucuronides. The mass spectrometric response for these compounds from different locations in the liver showed an increase with increasing extraction time (5, 20 and 40 s). For on-line separation and detection/identification of extracted proteins from dried sheep blood spots, two major protein peaks dominated the chromatogram and could be correlated with the expected masses for the hemoglobin α and β chains. Spatially resolved sampling, separation, and detection of small molecules and proteins from surfaces can be accomplished using a continuous-flow liquid microjunction surface sampling probe coupled on-line with HPLC/MS detection. Published in 2013. This article is a U.S. Government work and is in the public domain in the USA.

Comprehensive summary of beach renourishment and offshore sand removal impacts for Florida

USGS Publications Warehouse

Demopoulos, A.W.J.; Gualtieri, D.J.; Neils, A.; Huge, D.

2011-01-01

An essential first step in the scope of environmental impacts for a sediment mining project is a formulation of specific purpose, precise needs, and estimated impacts. For each individual project, scope must be described, acceptable alternatives must be determined, critical environmental issues must be identified, and mitigation measures must be resolved. Appropriate Federal and State regulations will often require evidence that sand placement is a reasonable alternative to shoreline protection. If so, material to be extracted from the borrow site must be characterized. Candidates must identify the extent of the potential area for sand resources, complete with screening criteria, and site-specific information must be obtained. Alternatives must be identified, compared, and contrasted. And, importantly, the most cost-effective and environmentally sound approach must be determined for the project to move forward. Florida's beaches and coastlines once provided natural protection against storm damage, while simultaneously supporting aquatic ecosystems and both commercial and recreational fisheries. However, beach erosion associated with regional construction and development of the coastline has reduced the effectiveness of natural storm protection. Coastal beaches are, in geological terms, ever-shifting and evolving through natural processes of erosion and replenishment. With permanent structures in place, such as seawalls, jetties, and revetments, natural shoreline is compartmentalized, dynamics are interrupted, and sediment is no longer replenished. Coastal erosion is often a problem where the natural sediment source is deficient. Many of Florida's beaches are now in need of beach replenishment to reduce the high level of damage caused by coastal flooding. Strategic placement of beach fill is a logical means for improving the stability of a shoreline where such a project is economically and environmentally feasible. Sand placement effectively extends the shoreline and provides protection for coastal developments. Beach nourishment or restoration must, however, be thought of as a continual effort and not a one-time fix. Therefore, a combination of sand placement with other erosion mitigation measures can be an effective way to stabilize a shoreline and extend the life of the beach nourishment. Fill material can be obtained from an offshore borrow site, and its characteristics must match the native material in terms of grain size and structure. Environmental concerns for such an effort include potential for decreased water quality during dredging operations, and disturbance of coastal habitat while removing or depositing dredged material. An in-depth scientific evaluation of deposit sites and potential borrow sites must be executed. Mitigation and monitoring efforts will also be critical for a successful low-impact beach management project. The potential exists for unwanted consequences to develop during dredging operations, all of which must be considered and reduced.-->

Improving striping operations through system optimization.

DOT National Transportation Integrated Search

2015-09-01

Striping operations generate a significant workload for Missouri Department of Transportation (MoDOT) maintenance : operations. The requirement for each striping crew to replenish its stock of paint and other consumable items from a bulk storage : fa...

Military Sealift Command

Science.gov Websites

well approximately 3 million gallons of jet fuel and 6 million gallons of diesel ship fuel to the USS replenishments-at-sea, delivering 740 pallets of food equipment, as well approximately 3 million gallons of jet

Molecular dynamics as a foundation for flux prediction through nanoporous membranes: A vectorized, constraint-free approach to conservative simulations

NASA Astrophysics Data System (ADS)

Inman, Matthew Clay

A novel, open-cathode direct methanol fuel cell (DMFC ) has been designed and built by researchers at the University of North Florida and University of Florida. Foremost among the advances of this system over previous DMFC architectures is a passive water recovery system which allows product water to replenish that consumed at the anode. This is enabled by a specially-designed water pathway combined with a liquid barrier layer (LBL ). The LBL membrane is positioned between the cathode catalyst layer and the cathode gas diffusion layer, and must exhibit high permeability and low diffusive resistance to both oxygen and water vapor, bulk hydrophobicity to hold back the product liquid water, and must remain electrically conductive. Maintaining water balance at optimum operating temperatures is problematic with the current LBL design, forcing the system to run at lower temperatures decreasing the overall system efficiency. This research presents a novel approach to nanoporous membrane design whereby flux of a given species is determined based upon the molecular properties of said species and those of the diffusing medium, the pore geometry, and the membrane thickness. A molecular dynamics (MD ) model is developed for tracking Knudsen regime flows of a Lennard-Jones (LJ ) fluid through an atomistic pore structure, hundreds of thousands of wall collision simulations are performed on the University of Florida HiPerGator supercomputer, and the generated trajectory information is used to develop number density and axial velocity profiles for use in a rigorous approach to total flux calculation absent in previously attempted MD models. Results are compared to other published approaches and diffusion data available in the literature. The impact of this study on various applications of membrane design is discussed and additional simulations and model improvements are outlined for future consideration.

26 CFR 1.884-2 - Special rules for termination or incorporation of a U.S. trade or business or liquidation or...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Special rules for termination or incorporation of a U.S. trade or business or liquidation or reorganization of a foreign corporation or its domestic subsidiary. 1.884-2 Section 1.884-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME...