Mosquito and Fly Surveillance and Control Research at the USDA-ARS Center for Medical, Agricultural and Veterinary Entomology: Solving Operational Challenges

USDA-ARS?s Scientific Manuscript database

The Mosquito and Fly Research Unit of the USDA-ARS Center for Medical, Agricultural and Veterinary Entomology located in Gainesville Florida is the largest Federal laboratory devoted to specifically solving operational mosquito and fly surveillance and control challenges in the U.S. and internationa...

Solar Sail Attitude Control Performance Comparison

NASA Technical Reports Server (NTRS)

Bladt, Jeff J.; Lawrence, Dale A.

2005-01-01

Performance of two solar sail attitude control implementations is evaluated. One implementation employs four articulated reflective vanes located at the periphery of the sail assembly to generate control torque about all three axes. A second attitude control configuration uses mass on a gimbaled boom to alter the center-of-mass location relative to the center-of-pressure producing roll and pitch torque along with a pair of articulated control vanes for yaw control. Command generation algorithms employ linearized dynamics with a feedback inversion loop to map desired vehicle attitude control torque into vane and/or gimbal articulation angle commands. We investigate the impact on actuator deflection angle behavior due to variations in how the Jacobian matrix is incorporated into the feedback inversion loop. Additionally, we compare how well each implementation tracks a commanded thrust profile, which has been generated to follow an orbit trajectory from the sun-earth L1 point to a sub-L1 station.

Efficacy of Prophyt when combined with Captec for control of peach scab in Alabama, 2014

USDA-ARS?s Scientific Manuscript database

Fungicides were evaluated for control of scab in a mid-ripening peach experimental block (‘Ruston Red’) located at the Chilton Area Research and Extension Center located in Clanton, AL. Chemical formulations were applied with an airblast sprayer (100 gal/A spray volume) at the petal fall and shuck s...

Automatic brightness control of laser spot vision inspection system

NASA Astrophysics Data System (ADS)

Han, Yang; Zhang, Zhaoxia; Chen, Xiaodong; Yu, Daoyin

2009-10-01

The laser spot detection system aims to locate the center of the laser spot after long-distance transmission. The accuracy of positioning laser spot center depends very much on the system's ability to control brightness. In this paper, an automatic brightness control system with high-performance is designed using the device of FPGA. The brightness is controlled by combination of auto aperture (video driver) and adaptive exposure algorithm, and clear images with proper exposure are obtained under different conditions of illumination. Automatic brightness control system creates favorable conditions for positioning of the laser spot center later, and experiment results illuminate the measurement accuracy of the system has been effectively guaranteed. The average error of the spot center is within 0.5mm.

View of Mission Control Center during Apollo 13 splashdown

NASA Image and Video Library

1970-04-17

S70-35148 (17 April 1970) --- Staff members from NASA Headquarters (NASA HQ), Manned Spacecraft Center (MSC), and Dr. Thomas Paine (center of frame) applaud the successful splashdown of the Apollo 13 mission while Dr. George Low smokes a cigar (right), in the MSC Mission Control Center (MCC), located in Building 30. Apollo 13 crewmembers, astronauts James A. Lovell Jr., commander; John L. Swigert Jr., command module pilot; and Fred W. Haise Jr., lunar module pilot, splashed down at 12:07:44 p.m. (CST), April 17, 1970, in the south Pacific Ocean.

Radiological Control Center (RADCC) Renaming Ceremony

NASA Image and Video Library

2017-03-31

Consoles in the Radiological Control Center at NASA's Kennedy Space Center are seen during ceremonies to name the facility in honor of Randy Scott. A professional health physicist of more than 40 years, Scott served as the Florida spaceport's Radiation Protection Officer for 14 years until his death June 17, 2016. Located in the Neil Armstrong Operations and Checkout building, the Randall E. Scott Radiological Control Center is staffed by technical and radiological experts from NASA, the U.S. Department of Energy, the U.S. Air Force 45th Space Wing and the state of Florida. The group performs data collection and assessment functions supporting launch site and field data collection activities.

Radiological Control Center (RADCC) Renaming Ceremony

NASA Image and Video Library

2017-03-31

A portion of the Radiological Control Center at NASA's Kennedy Space Center is seen during ceremonies to name the facility in honor of Randy Scott. A professional health physicist of more than 40 years, Scott served as the Florida spaceport's Radiation Protection Officer for 14 years until his death June 17, 2016. Located in the Neil Armstrong Operations and Checkout building, the Randall E. Scott Radiological Control Center is staffed by technical and radiological experts from NASA, the U.S. Department of Energy, the U.S. Air Force 45th Space Wing and the state of Florida. The group performs data collection and assessment functions supporting launch site and field data collection activities.

Low speed aerodynamic characteristics of a lifting-body hypersonic research aircraft configuration

NASA Technical Reports Server (NTRS)

Penland, J. A.

1975-01-01

An experimental investigation of the low-speed longitudinal, lateral, and directional stability characteristics of a lifting-body hypersonic research airplane concept was conducted in a low-speed tunnel with a 12-foot (3.66-meter) octagonal test section at the Langley Research Center. The model was tested with two sets of horizontal and vertical tip controls having different planform areas, a center vertical tail and two sets of canard controls having trapezoidal and delta planforms, and retracted and deployed engine modules and canopy. This investigation was conducted at a dynamic pressure of 239.4 Pa (5 psf) (Mach number of 0.06) and a Reynolds number of 2 million based on the fuselage length. The tests were conducted through an angle-of-attack range of 0 deg to 30 deg and through horizontal-tail deflections of 10 deg to minus 30 deg. The complete configuration exhibited excessive positive static longitudinal stability about the design center-of-gravity location. However, the configuration was unstable laterally at low angles of attack and unstable directionally throughout the angle-of-attack range. Longitudinal control was insufficient to trim at usable angles of attack. Experiments showed that a rearward shift of the center of gravity and the use of a center-located vertical tail would result in a stable and controllable vehicle.

Prescription and over-the-counter medications tool kit.

DOT National Transportation Integrated Search

2011-04-01

Automatic vehicle location (AVL) is a computer-based vehicle tracking system. For transit, the actual real-time position of each vehicle is measured and its location is relayed to a control center. Actual position determination and relay techniques v...

Cable-fault locator

NASA Technical Reports Server (NTRS)

Cason, R. L.; Mcstay, J. J.; Heymann, A. P., Sr.

1979-01-01

Inexpensive system automatically indicates location of short-circuited section of power cable. Monitor does not require that cable be disconnected from its power source or that test signals be applied. Instead, ground-current sensors are installed in manholes or at other selected locations along cable run. When fault occurs, sensors transmit information about fault location to control center. Repair crew can be sent to location and cable can be returned to service with minimum of downtime.

Trusted Data Communication and Security Issues in Gnss Network of Turkey

NASA Astrophysics Data System (ADS)

Bakici, S.; Erkek, B.; Manti, V.; Altekin, A.

2017-11-01

There are three main activities of General Directorate of Land Registry and Cadastre. These are Mapping, Land Registry and Cadastre. Geomatic Department is responsible for mapping activities. The most important projects like TUSAGA-Aktif (CORS-Tr), Metadata Geoportal, Orthophoto Production and orthophoto web services and preparation of Turkish NSDI Feasibility Report have been conducted and completed by this department's specialists since 2005. TUSAGA-Aktif (CORS-Tr) System, serves location information at cm level accuracy in Turkey and TR Nortern Cyprus in few seconds, where adequate numbers of GNSS satellites are observed and communication possibilities are present. No ground control points and benchmarks are necessary. There are 146 permanent GNSS stations within the CORS-Tr System. Station data are transferred online to the main control center located in the Mapping Department of the General Directorate of Land Registry and Cadastre and to the control center located in the General Command of Mapping. Currently CORS-Tr has more than 9000 users. Most of them are private companies working for governmental organization. Providing data communication between control center and both GNSS station and users via trusted and good substructure is important. Additionally, protection of the system and data against cyber attacks from domestic and foreign sources is important. This paper focuses on data communication and security issues of GNSS network named TUSAGA-Aktif.

16. NBS TOPSIDE CONTROL ROOM, THE NBS HYPERBARIC CHAMBER IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. NBS TOPSIDE CONTROL ROOM, THE NBS HYPERBARIC CHAMBER IS VERY CLOSE TO THE WATER'S EDGE AND HERE FOR DIVER EMERGENCY SUPPORT. A MEDICAL STAFF IS LOCATED ON THE MARSHALL SPACE FLIGHT CENTER (MSFC) AND SUPPORTS THE NBS PERSONNEL WHEN HYPERBARIC CHAMBER OPERATION IS NECESSARY. - Marshall Space Flight Center, Neutral Buoyancy Simulator Facility, Rideout Road, Huntsville, Madison County, AL

NASA’s Improved Supersonic Cockpit Display Shows Precise Locations of Sonic Booms

NASA Image and Video Library

2016-10-06

Engineers and researchers at NASA’s Armstrong Flight Research Center monitored the flights, and were able to observe the mapping of the sonic boom carpet from the F-18, from the center’s Mission Control Center.

Environmental impact statement Space Shuttle advanced solid rocket motor program

NASA Technical Reports Server (NTRS)

1989-01-01

The proposed action is design, development, testing, and evaluation of Advanced Solid Rocket Motors (ASRM) to replace the motors currently used to launch the Space Shuttle. The proposed action includes design, construction, and operation of new government-owned, contractor-operated facilities for manufacturing and testing the ASRM's. The proposed action also includes transport of propellant-filled rocket motor segments from the manufacturing facility to the testing and launch sites and the return of used and/or refurbished segments to the manufacturing site. Sites being considered for the new facilities include John C. Stennis Space Center, Hancock County, Mississippi; the Yellow Creek site in Tishomingo County, Mississippi, which is currently in the custody and control of the Tennessee Valley Authority; and John F. Kennedy Space Center, Brevard County, Florida. TVA proposes to transfer its site to the custody and control of NASA if it is the selected site. All facilities need not be located at the same site. Existing facilities which may provide support for the program include Michoud Assembly Facility, New Orleans Parish, Louisiana; and Slidell Computer Center, St. Tammany Parish, Louisiana. NASA's preferred production location is the Yellow Creek site, and the preferred test location is the Stennis Space Center.

Operating and Managing a Backup Control Center

NASA Technical Reports Server (NTRS)

Marsh, Angela L.; Pirani, Joseph L.; Bornas, Nicholas

2010-01-01

Due to the criticality of continuous mission operations, some control centers must plan for alternate locations in the event an emergency shuts down the primary control center. Johnson Space Center (JSC) in Houston, Texas is the Mission Control Center (MCC) for the International Space Station (ISS). Due to Houston s proximity to the Gulf of Mexico, JSC is prone to threats from hurricanes which could cause flooding, wind damage, and electrical outages to the buildings supporting the MCC. Marshall Space Flight Center (MSFC) has the capability to be the Backup Control Center for the ISS if the situation is needed. While the MSFC Huntsville Operations Support Center (HOSC) does house the BCC, the prime customer and operator of the ISS is still the JSC flight operations team. To satisfy the customer and maintain continuous mission operations, the BCC has critical infrastructure that hosts ISS ground systems and flight operations equipment that mirrors the prime mission control facility. However, a complete duplicate of Mission Control Center in another remote location is very expensive to recreate. The HOSC has infrastructure and services that MCC utilized for its backup control center to reduce the costs of a somewhat redundant service. While labor talents are equivalent, experiences are not. Certain operations are maintained in a redundant mode, while others are simply maintained as single string with adequate sparing levels of equipment. Personnel at the BCC facility must be trained and certified to an adequate level on primary MCC systems. Negotiations with the customer were done to match requirements with existing capabilities, and to prioritize resources for appropriate level of service. Because some of these systems are shared, an activation of the backup control center will cause a suspension of scheduled HOSC activities that may share resources needed by the BCC. For example, the MCC is monitoring a hurricane in the Gulf of Mexico. As the threat to MCC increases, HOSC must begin a phased activation of the BCC, while working resource conflicts with normal HOSC activities. In a long duration outage to the MCC, this could cause serious impacts to the BCC host facility s primary mission support activities. This management of a BCC is worked based on customer expectations and negotiations done before emergencies occur. I.

KENNEDY SPACE CENTER, FLA. - Louis MacDowell (right), Testbed manager, explains to Center Director Jim Kennedy the use of astmospheric calibration specimens. Placed at various locations, they can rank the corrosivity of the given environment. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - Louis MacDowell (right), Testbed manager, explains to Center Director Jim Kennedy the use of astmospheric calibration specimens. Placed at various locations, they can rank the corrosivity of the given environment. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

Installation of active noise control and active vibration control on a GP40-2 locomotive : final report.

DOT National Transportation Integrated Search

2016-06-01

This project evaluated the performance of active noise control (ANC) and active vibration control (AVC) technologies using a GP40-2 locomotive located at the Transportation Technology Center (TTC) near Pueblo, CO, to determine the applicability of AN...

Implications of acceleration environments on scaling materials processing in space to production

NASA Technical Reports Server (NTRS)

Demel, Ken

1990-01-01

Some considerations regarding materials processing in space are covered from a commercial perspective. Key areas include power, proprietary data, operational requirements (including logistics), and also the center of gravity location, and control of that location with respect to materials processing payloads.

Bird Vision System

NASA Technical Reports Server (NTRS)

2008-01-01

The Bird Vision system is a multicamera photogrammerty software application that runs on a Microsoft Windows XP platform and was developed at Kennedy Space Center by ASRC Aerospace. This software system collects data about the locations of birds within a volume centered on the Space Shuttle and transmits it in real time to the laptop computer of a test director in the Launch Control Center (LCC) Firing Room.

Instructional Media Center. Educational Facility Series. A Guide to Planning.

ERIC Educational Resources Information Center

Esposito, Nicholas A., Ed.

General recommendations are set forth regarding aesthetics, acoustics, lighting, temperature control, location, and layout of the instructional media center. Consideration is given to spatial relationships, equipment and furnishings, and suggestions are included regarding basic and advance facilities for primary, middle and secondary schools. (FS)

STS-26 long duration simulation in JSC Mission Control Center (MCC) Bldg 30

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 long duration simulation is conducted in JSC Mission Control Center (MCC) Bldg 30 Flight Control Room (FCR). Front row of consoles with Propulsion Engineer (PROP) and Guidance, Navigation, and Control Systems Engineer (GNC) are visible in the foreground. CBS television camera personnel record front visual displays (orbital chart and data) for '48 Hours' program to be broadcast at a later date. The integrated simulation involved communicating with crewmembers stationed in the fixed based (FB) shuttle mission simulator (SMS) located in JSC Mission Simulation and Training Facility Bldg 5.

STS-26 long duration simulation in JSC Mission Control Center (MCC) Bldg 30

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 long duration simulation is conducted in JSC Mission Control Center (MCC) Bldg 30 Flight Control Room (FCR). Director of Mission Operations Directorate (MOD) Eugene F. Kranz (left) and Chief of the Flight Directors Office Tommy W. Holloway monitor activity during the simulation. The two are at their normal stations on the rear row of consoles. The integrated simulation involves MCC flight controllers communicating with crewmembers stationed in the fixed based (FB) shuttle mission simulator (SMS) located in JSC Mission Simulation and Training Facility Bldg 5.

System Finds Horizontal Location of Center of Gravity

NASA Technical Reports Server (NTRS)

Johnston, Albert S.; Howard, Richard T.; Brewster, Linda L.

2006-01-01

An instrumentation system rapidly and repeatedly determines the horizontal location of the center of gravity of a laboratory vehicle that slides horizontally on three air bearings (see Figure 1). Typically, knowledge of the horizontal center-of-mass location of such a vehicle is needed in order to balance the vehicle properly for an experiment and/or to assess the dynamic behavior of the vehicle. The system includes a load cell above each air bearing, electronic circuits that generate digital readings of the weight on each load cell, and a computer equipped with software that processes the readings. The total weight and, hence, the mass of the vehicle are computed from the sum of the load-cell weight readings. Then the horizontal position of the center of gravity is calculated straightforwardly as the weighted sum of the known position vectors of the air bearings, the contribution of each bearing being proportional to the weight on that bearing. In the initial application for which this system was devised, the center- of-mass calculation is particularly simple because the air bearings are located at corners of an equilateral triangle. However, the system is not restricted to this simple geometry. The system acquires and processes weight readings at a rate of 800 Hz for each load cell. The total weight and the horizontal location of the center of gravity are updated at a rate of 800/3 approx. equals 267 Hz. In a typical application, a technician would use the center-of-mass output of this instrumentation system as a guide to the manual placement of small weights on the vehicle to shift the center of gravity to a desired horizontal position. Usually, the desired horizontal position is that of the geometric center. Alternatively, this instrumentation system could be used to provide position feedback for a control system that would cause weights to be shifted automatically (see Figure 2) in an effort to keep the center of gravity at the geometric center.

65. DETAIL OF ASSISTANT LAUNCH CONTROLLER AND LAUNCH CONTROLLER PANELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

65. DETAIL OF ASSISTANT LAUNCH CONTROLLER AND LAUNCH CONTROLLER PANELS LOCATED NEAR CENTER OF SLC-3E CONTROL ROOM. NOTE 30-CHANNEL COMMUNICATIONS PANELS. PAYLOAD ENVIRONMENTAL CONTROL AND MONITORING PANELS (LEFT) AND LAUNCH OPERATORS PANEL (RIGHT) IN BACKGROUND. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Operations Building, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Populating a Control Point Database: A cooperative effort between the USGS, Grand Canyon Monitoring and Research Center and the Grand Canyon Youth Organization

NASA Astrophysics Data System (ADS)

Brown, K. M.; Fritzinger, C.; Wharton, E.

2004-12-01

The Grand Canyon Monitoring and Research Center measures the effects of Glen Canyon Dam operations on the resources along the Colorado River from Glen Canyon Dam to Lake Mead in support of the Grand Canyon Adaptive Management Program. Control points are integral for geo-referencing the myriad of data collected in the Grand Canyon including aerial photography, topographic and bathymetric data used for classification and change-detection analysis of physical, biologic and cultural resources. The survey department has compiled a list of 870 control points installed by various organizations needing to establish a consistent reference for data collected at field sites along the 240 mile stretch of Colorado River in the Grand Canyon. This list is the foundation for the Control Point Database established primarily for researchers, to locate control points and independently geo-reference collected field data. The database has the potential to be a valuable mapping tool for assisting researchers to easily locate a control point and reduce the occurrance of unknowingly installing new control points within close proximity of an existing control point. The database is missing photographs and accurate site description information. Current site descriptions do not accurately define the location of the point but refer to the project that used the point, or some other interesting fact associated with the point. The Grand Canyon Monitoring and Research Center (GCMRC) resolved this problem by turning the data collection effort into an educational exercise for the participants of the Grand Canyon Youth organization. Grand Canyon Youth is a non-profit organization providing experiential education for middle and high school aged youth. GCMRC and the Grand Canyon Youth formed a partnership where GCMRC provided the logistical support, equipment, and training to conduct the field work, and the Grand Canyon Youth provided the time and personnel to complete the field work. Two data collection efforts were conducted during the 2004 summer allowing 40 youth the opportunity to contribute valuable information to the Control Point Database. This information included: verification of point existence, photographs, accurate site descriptions concisely describing the location of the point, how to reach the point, the specific point location and detailed bearings to visible and obvious land marks. The youth learned to locate themselves and find the points using 1:1000 airphotos, write detailed site descriptions, take bearings with a compass, measure vertical and horizontal distances, and use a digital camera. The youth found information for 252 control points (29% of the total points).

Use of Virtual Mission Operations Center Technology to Achieve JPDO's Virtual Tower Vision

NASA Technical Reports Server (NTRS)

Ivancic, William D.; Paulsen, Phillip E.

2006-01-01

The Joint Program Development Office has proposed that the Next Generation Air Transportation System (NGATS) consolidate control centers. NGATS would be managed from a few strategically located facilities with virtual towers and TRACONS. This consolidation is about combining the delivery locations for these services not about decreasing service. By consolidating these locations, cost savings in the order of $500 million have been projected. Evolving to spaced-based communication, navigation, and surveillance offers the opportunity to reduce or eliminate much of the ground-based infrastructure cost. Dynamically adjusted airspace offers the opportunity to reduce the number of sectors and boundary inconsistencies; eliminate or reduce "handoffs;" and eliminate the distinction between Towers, TRACONS, and Enroute Centers. To realize a consolidation vision for air traffic management there must be investment in networking. One technology that holds great potential is the use of Virtual Mission Operations Centers to provide secure, automated, intelligent management of the NGATS. This paper provides a conceptual framework for incorporating VMOC into the NGATS.

Review of LOGEX. Main Report and Appendixes A-I

DTIC Science & Technology

1975-05-23

been developed on an RCA Spectra 70 machine located at the Army Logistics Management Center, Fort Lee, Virginia. This was undoubtedly an outstanding...Control Number ADP - Automatic Data Processing ACT - Active Duty for Training ALMC - US Army Logistics Management Center AMO - Ammunition AR - Amy...Directorate CPT McClellan, LOGEX Directorate CPT Weaver, LOGEX Directorate United States Army Logistics Management Center Mr. Loper Mr. Ross United States

KSC-05PD-1461

NASA Technical Reports Server (NTRS)

2005-01-01

KENNEDY SPACE CENTER, FLA. At the Shuttle Landing Facility on NASAs Kennedy Space Center, KSC Director Jim Kennedy talks to attendees at the ribbon-cutting ceremony for the new NASA Air Traffic Control Tower. The dedication took place in the SLFs new media facilities, which were built for the Return to Flight mission STS-114 and the landing of Shuttle Discovery. The facilities are co-located with the new control tower. The dedication and ribbon cutting were held at the base of the tower and included Center Director Jim Kennedy, Space Gateway Support President William A. Sample, External Relations Director Lisa Malone, Center Operations Director Scott D. Kerr, and KSC Safety Aviation Officer Albert E. Taff. The structure rises 110 feet over the midpoint of the runway and offers air traffic controllers a magnificent 360-degree view of Kennedy Space Center, Cape Canaveral Air Force Station and north Brevard County. It replaces the small, portable tower installed at the edge of the runway in 1986. The new control tower will manage all landings and departures from the SLF, including air traffic within the Kennedy Space Center-Cape Canaveral restricted airspace. The facility provides a 24-hour weather-observing facility providing official hourly weather observations for the SLF and the Cape Canaveral vicinity, including special observations for all launches and landings. State-of-the-art, weather-observing equipment has been installed for Space Shuttle landings and for serving conventional aircraft landing at the SLF. At this location, weather observers will have a multi- directional view of the weather conditions at the runway and Launch Complex 39.

Automatic frame-centered object representation and integration revealed by iconic memory, visual priming, and backward masking.

PubMed

Lin, Zhicheng; He, Sheng

2012-10-25

Object identities ("what") and their spatial locations ("where") are processed in distinct pathways in the visual system, raising the question of how the what and where information is integrated. Because of object motions and eye movements, the retina-based representations are unstable, necessitating nonretinotopic representation and integration. A potential mechanism is to code and update objects according to their reference frames (i.e., frame-centered representation and integration). To isolate frame-centered processes, in a frame-to-frame apparent motion configuration, we (a) presented two preceding or trailing objects on the same frame, equidistant from the target on the other frame, to control for object-based (frame-based) effect and space-based effect, and (b) manipulated the target's relative location within its frame to probe frame-centered effect. We show that iconic memory, visual priming, and backward masking depend on objects' relative frame locations, orthogonal of the retinotopic coordinate. These findings not only reveal that iconic memory, visual priming, and backward masking can be nonretinotopic but also demonstrate that these processes are automatically constrained by contextual frames through a frame-centered mechanism. Thus, object representation is robustly and automatically coupled to its reference frame and continuously being updated through a frame-centered, location-specific mechanism. These findings lead to an object cabinet framework, in which objects ("files") within the reference frame ("cabinet") are orderly coded relative to the frame.

Earth Observations

NASA Image and Video Library

2010-07-31

ISS024-E-010403 (31 July 2010) --- This detailed image ? photographed by an Expedition 24 crew member on the International Space Station (ISS) ? is centered on the NASA Lyndon B. Johnson Space Center (JSC), located in the southeastern Houston, TX metropolitan area. While initially being represented by a number of temporary locations in Houston, the facility was established in 1961 as the Manned Spacecraft Center and renamed in honor of the late U.S. President Johnson (a Texas native) in 1973. JSC serves as the lead NASA center for both astronaut training and mission control of manned spacecraft - such as the ISS and space shuttle - and has done so throughout the history of the U.S. manned space program. The Center also collaborates with other NASA and international partner facilities in a variety of scientific and engineering programs related to human spaceflight and planetary exploration. JSC is located approximately midway between downtown Houston and Galveston, TX, and is bordered by several smaller municipalities that form a mosaic of urban and suburban land use (grey areas with street grids, and commercial/industrial areas characterized by white rooftops). Large tracts of grassy fields and forests in the area (light to dark green respectively) include nature preserves, grazing lands, and flood control areas. Also visible at upper left is Ellington Field. This airport services a variety of NASA aircraft used for astronaut training, scientific, and cargo transport purposes. Clear Lake, an inlet of Galveston Bay, is located to the immediate southeast of JSC. Both Clear Lake and Galveston Bay appear silver-grey due to sunglint, or light reflected back towards the observer on the ISS that gives the water surface a mirror-like appearance. Several boat wakes are visible in Galveston Bay (right) due to disruption of the water surface that reduces the sunglint effect.

KSC-99pp1215

NASA Image and Video Library

1999-10-14

Seen from above, construction of a new site at KSC's Visitor Complex, The Early Space Exploration and Conference Center, is nearly finished. It is expected to be open to the public by mid-November. The space exploration facility will feature Mercury and Gemini capsules and the recently relocated Mission Control Center. Attached to it is a state-of-the-art conference center. Built by Delaware North Park Services, the facility is located between the Rock Garden and the Center for Space Education

Manpower Requirements for Air Traffic Control and Flight Service Specialists in Indiana.

ERIC Educational Resources Information Center

Purdue Univ., Lafayette, IN. Office of Manpower Studies.

As of January 1, 1968 the Federal Aviation Administration (FAA) of the United States Department of Transportation employed 6,963 controllers in airport towers, 7,617 controllers in Air Route Traffic Control Centers, and 4,459 flight service specialists at airport locations. Projected needs are as follows: (1) Controllers in airport towers:…

LSS systems planning and performance program

NASA Technical Reports Server (NTRS)

Mckenna, Victoria Jones; Dendy, Michael J.; Naumann, Charles B.; Rice, Sally A.; Weathers, John M.

1993-01-01

This report describes, using viewgraphs, the Marshall Space Flight Center's Large Space Structures Ground Test Facilities located in building 4619. Major topics include the Active Control Evaluation of Systems (ACES) Laboratory; the Control-Structures Interaction/Controls, Astrophysics, and Structures Experiment in Space (CSI/CASES); Advanced Development Facility; and the ACES Guest Investigator Program.

Mission Control Center (MCC) View - Apollo 13 Oxygen Cell Failure - MSC

NASA Image and Video Library

1970-04-15

S70-35014 (15 April 1970) --- A group of flight controllers gathers around the console of Glenn S. Lunney (seated, nearest camera), Shift 4 flight director, in the Mission Operations Control Room (MOCR) of Mission Control Center (MCC), located in Building 30 at the Manned Spacecraft Center (MSC). Their attention is drawn to a weather map of the proposed landing site in the South Pacific Ocean. Among those looking on is Dr. Christopher C. Kraft, deputy director, MSC, standing in black suit, on right. When this photograph was taken, the Apollo 13 lunar landing mission had been canceled, and the problem-plagued Apollo 13 crew members were in trans-Earth trajectory attempting to bring their crippled spacecraft back home.

Incorporating location, routing, and inventory decisions in a bi-objective supply chain design problem with risk-pooling

NASA Astrophysics Data System (ADS)

Tavakkoli-Moghaddam, Reza; Forouzanfar, Fateme; Ebrahimnejad, Sadoullah

2013-07-01

This paper considers a single-sourcing network design problem for a three-level supply chain. For the first time, a novel mathematical model is presented considering risk-pooling, the inventory existence at distribution centers (DCs) under demand uncertainty, the existence of several alternatives to transport the product between facilities, and routing of vehicles from distribution centers to customer in a stochastic supply chain system, simultaneously. This problem is formulated as a bi-objective stochastic mixed-integer nonlinear programming model. The aim of this model is to determine the number of located distribution centers, their locations, and capacity levels, and allocating customers to distribution centers and distribution centers to suppliers. It also determines the inventory control decisions on the amount of ordered products and the amount of safety stocks at each opened DC, selecting a type of vehicle for transportation. Moreover, it determines routing decisions, such as determination of vehicles' routes starting from an opened distribution center to serve its allocated customers and returning to that distribution center. All are done in a way that the total system cost and the total transportation time are minimized. The Lingo software is used to solve the presented model. The computational results are illustrated in this paper.

The role of clinical toxicologists and poison control centers in public health.

PubMed

Sutter, Mark E; Bronstein, Alvin C; Heard, Stuart E; Barthold, Claudia L; Lando, James; Lewis, Lauren S; Schier, Joshua G

2010-06-01

Poison control centers and clinical toxicologists serve many roles within public health; however, the degree to which these entities collaborate is unknown. The objective of this survey was to identify successful collaborations of public health agencies with clinical toxicologists and poison control centers. Four areas including outbreak identification, syndromic surveillance, terrorism preparedness, and daily public health responsibilities amenable to poison control center resources were assessed. An online survey was sent to the directors of poison control centers, state epidemiologists, and the most senior public health official in each state and selected major metropolitan areas. This survey focused on three areas: service, structure within the local or state public health system, and remuneration. Questions regarding remuneration and poison control center location within the public health structure were asked to assess if these were critical factors of successful collaborations. Senior state and local public health officials were excluded because of a low response rate. The survey was completed in October 2007. A total of 111 respondents, 61 poison control centers and 50 state epidemiologists, were eligible for the survey. Sixty-nine (62%) of the 111 respondents, completed and returned the survey. Thirty-three (54%) of the 61 poison control centers responded, and 36 of the 50 state epidemiologists (72%) responded. The most frequent collaborations were terrorism preparedness and epidemic illness reporting. Additional collaborations also exist. Important collaborations exist outside of remuneration or poison control centers being a formal part of the public health structure. Poison control centers have expanded their efforts to include outbreak identification, syndromic surveillance, terrorism preparedness, and daily public health responsibilities amenable to poison control center resources. Collaboration in these areas and others should be expanded. Published by Elsevier Inc.

Bonneville, Power Administration Timing System

NASA Technical Reports Server (NTRS)

Martin, Kenneth E.

1996-01-01

Time is an integral part of the Bonneville Power Administration's (BPA) operational systems. Generation and power transfers are planned in advance. Utilities coordinate with each other by making these adjustments on a timed schedule. Price varies with demand, so billing is based on time. Outages for maintenance are scheduled to assure they do not interrupt reliable power delivery. Disturbance records are aligned with recorded timetags for analysis and comparison with related information. Advanced applications like traveling wave fault location and real-time phase measurement require continuous timing with high precision. Most of BPA is served by a Central Time System (CTS) at the Dittmer Control Center near Portland, OR. This system keeps time locally and supplies time to both the control center systems and field locations via a microwave signal. It is kept synchronized to national standard time and coordinated with interconnected utilities. It is the official BPA time. Powwer system control and operation is described, followed by a description of BPA timing systems including CTS, the Fault Location Acquisition Reporter, time dissemination, and phasor measurements. References are provided for further reading.

Generation of Aerodynamics Via Physics-Based Virtual Flight Simulations

DTIC Science & Technology

2008-12-01

problems associated with projectile and missile aerodynamics. For maneuvering munitions, the effect of many new weapon control mechanisms being...dynamic simulation. The terms containing YPAC constitute the Magnus air load acting at the Magnus center of pressure while the terms containing 0 2...an unsteady aerodynamic moment along with terms due to the fact that the center of pressure and center of Magnus are not located at the mass

Lightning location system supervising Swedish power transmission network

NASA Technical Reports Server (NTRS)

Melin, Stefan A.

1991-01-01

For electric utilities, the ability to prevent or minimize lightning damage on personnel and power systems is of great importance. Therefore, the Swedish State Power Board, has been using data since 1983 from a nationwide lightning location system (LLS) for accurately locating lightning ground strikes. Lightning data is distributed and presented on color graphic displays at regional power network control centers as well as at the national power system control center for optimal data use. The main objectives for use of LLS data are: supervising the power system for optimal and safe use of the transmission and generating capacity during periods of thunderstorms; warning service to maintenance and service crews at power line and substations to end operations hazardous when lightning; rapid positioning of emergency crews to locate network damage at areas of detected lightning; and post analysis of power outages and transmission faults in relation to lightning, using archived lightning data for determination of appropriate design and insulation levels of equipment. Staff have found LLS data useful and economically justified since the availability of power system has increased as well as level of personnel safety.

STS-26 long duration simulation in JSC Mission Control Center (MCC) Bldg 30

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 long duration simulation is conducted in JSC Mission Control Center (MCC) Bldg 30 Flight Control Room (FCR). CBS television camera personnel record MCC activities at Spacecraft Communicator (CAPCOM) and Flight Activities Officer (FAO) (foreground) consoles for '48 Hours' program to be broadcast at a later date. The integrated simulation involved communicating with crewmembers stationed in the fixed based (FB) shuttle mission simulator (SMS) located in JSC Mission Simulation and Training Facility Bldg 5. MCC FCR visual displays are seen in front of the rows of consoles.

INFLIGHT (MISSION CONTROL CENTER) - STS-2 - JSC

NASA Image and Video Library

1981-11-13

S81-39494 (12 Nov. 1981) --- An overall view of activity in the mission operations control room (MOCR) in Houston?s Mission Control Center (MCC) as viewed from the second front row of consoles during the STS-2 mission. The remote manipulator system (RMS) console is in the immediate foreground. Note TV transmission on the Eidophor screen at front of MOCR and shuttle orbiter marker on tracking map at left indicating the vehicle?s location over the Hawaiian Islands. The downlink was through the Hawaii tracking station. Photo credit: NASA

Evaluation of the LA 1 bridge at the Morganza flood control structure.

DOT National Transportation Integrated Search

2010-11-01

This technical assistance report documents the investigation conducted by the Louisiana Transportation : Research Center (LTRC) of the LA 1 Bridge located at the flood control structure near Morganza, LA. : The in-place condition of the bridge deck s...

Evaluation of the LA 1 bridge at the Morganza flood control structure.

DOT National Transportation Integrated Search

2010-11-01

This technical assistance report documents the investigation conducted by the Louisiana Transportation Research Center (LTRC) of the LA 1 Bridge located at the flood control structure near Morganza, LA. The in-place condition of the bridge deck showe...

Aerial view of a new site at KSC's Visitor Complex

NASA Technical Reports Server (NTRS)

1999-01-01

Seen from above, construction of a new site at KSC's Visitor Complex, The Early Space Exploration and Conference Center, is nearly finished. It is expected to be open to the public by mid- November. The space exploration facility will feature Mercury and Gemini capsules and the recently relocated Mission Control Center. Attached to it is a state-of-the-art conference center. Built by Delaware North Park Services, the facility is located between the Rock Garden and the Center for Space Education.

40 CFR 52.2450 - Conditional approval.

Code of Federal Regulations, 2010 CFR

2010-07-01

... reasonably available control technology (RACT) for the Manufacturing Center located in Richmond, Virginia is...) Revises the 1999-2005 portion of the severe area rate-of-progress plan to provide MOBILE6-based mobile...) Revises Reasonably Available Control Technology (RACT) rules to include the lower major source...

Automatic frame-centered object representation and integration revealed by iconic memory, visual priming, and backward masking

PubMed Central

Lin, Zhicheng; He, Sheng

2012-01-01

Object identities (“what”) and their spatial locations (“where”) are processed in distinct pathways in the visual system, raising the question of how the what and where information is integrated. Because of object motions and eye movements, the retina-based representations are unstable, necessitating nonretinotopic representation and integration. A potential mechanism is to code and update objects according to their reference frames (i.e., frame-centered representation and integration). To isolate frame-centered processes, in a frame-to-frame apparent motion configuration, we (a) presented two preceding or trailing objects on the same frame, equidistant from the target on the other frame, to control for object-based (frame-based) effect and space-based effect, and (b) manipulated the target's relative location within its frame to probe frame-centered effect. We show that iconic memory, visual priming, and backward masking depend on objects' relative frame locations, orthogonal of the retinotopic coordinate. These findings not only reveal that iconic memory, visual priming, and backward masking can be nonretinotopic but also demonstrate that these processes are automatically constrained by contextual frames through a frame-centered mechanism. Thus, object representation is robustly and automatically coupled to its reference frame and continuously being updated through a frame-centered, location-specific mechanism. These findings lead to an object cabinet framework, in which objects (“files”) within the reference frame (“cabinet”) are orderly coded relative to the frame. PMID:23104817

Former President George H.W. Bush paid a visit to NASA's Johnson Space Center to speak with Expedition 46 Commander Scott Kelly and Flight Engineer Tim Kopra and take a tour of the Space Vehicle Mockup Facility. Kelly���s twin brother, Mark Kelly and his wife, former Congresswoman Gabrielle Giffords were also present. Photo Date: February 5, 2016. Location: Building 30 - ISS Flight Control Room. Photographer: Robert Markowitz

NASA Image and Video Library

2016-02-05

Former President George H.W. Bush paid a visit to NASA's Johnson Space Center to speak with Expedition 46 Commander Scott Kelly and Flight Engineer Tim Kopra and take a tour of the Space Vehicle Mockup Facility. Kelly’s twin brother, Mark Kelly and his wife, former Congresswoman Gabrielle Giffords were also present. Photo Date: February 5, 2016. Location: Building 30 - ISS Flight Control Room. Photographer: Robert Markowitz

Space Shuttle hypersonic aerodynamic and aerothermodynamic flight research and the comparison to ground test results

NASA Technical Reports Server (NTRS)

Iliff, Kenneth W.; Shafer, Mary F.

1993-01-01

Aerodynamic and aerothermodynamic comparisons between flight and ground test for the Space Shuttle at hypersonic speeds are discussed. All of the comparisons are taken from papers published by researchers active in the Space Shuttle program. The aerodynamic comparisons include stability and control derivatives, center-of-pressure location, and reaction control jet interaction. Comparisons are also discussed for various forms of heating, including catalytic, boundary layer, top centerline, side fuselage, OMS pod, wing leading edge, and shock interaction. The jet interaction and center-of-pressure location flight values exceeded not only the predictions but also the uncertainties of the predictions. Predictions were significantly exceeded for the heating caused by the vortex impingement on the OMS pods and for heating caused by the wing leading-edge shock interaction.

Remote Transmission at High Speed

NASA Technical Reports Server (NTRS)

2003-01-01

Omni and NASA Test Operations at Stennis entered a Dual-Use Agreement to develop the FOTR-125, a 125 megabit-per-second fiber-optic transceiver that allows accurate digital recordings over a great distance. The transceiver s fiber-optic link can be as long as 25 kilometers. This makes it much longer than the standard coaxial link, which can be no longer than 50 meters.The FOTR-125 utilizes laser diode transmitter modules and integrated receivers for the optical interface. Two transmitters and two receivers are employed at each end of the link with automatic or manual switchover to maximize the reliability of the communications link. NASA uses the transceiver in Stennis High-Speed Data Acquisition System (HSDAS). The HSDAS consists of several identical systems installed on the Center s test stands to process all high-speed data related to its propulsion test programs. These transceivers allow the recorder and HSDAS controls to be located in the Test Control Center in a remote location while the digitizer is located on the test stand.

Stability Control of Grasping Objects with Different Locations of Center of Mass and Rotational Inertia

PubMed Central

Slota, Gregory P.; Suh, Moon Suk; Latash, Mark L.; Zatsiorsky, Vladimir M.

2012-01-01

The objective of this study was to observe how the digits of the hand adjust to varying location of the center of mass (CoM) above/below the grasp and rotational inertia (RI) of a hand held object. Such manipulations do not immediately affect the equilibrium equations while stability control is affected. Participants were instructed to hold a handle, instrumented with five force/torque transducers and a 3-D rotational tilt sensor, while either the location of the CoM or the RI values were adjusted. On the whole, people use two mechanisms to adjust to the changed stability requirements; they increase the grip force and redistribute the total moment between the normal and tangential forces offsetting internal torques. The increase in grip force, an internal force, and offsetting internal torques allows for increases in joint and hand rotational apparent stiffness while not creating external forces/torques which would unbalance the equations of equilibrium. PMID:22456054

Flair-fleet location and information reporting

NASA Technical Reports Server (NTRS)

Norman, E. R.; Dunlap, M. E.

1974-01-01

The FLAIR system, as now produced, automatically updates each vehicle's location and corresponding officer's status once each two seconds and presents this information to police dispatchers in the command and control center. The position of all vehicles available for assignment is displayed on a color video map at each dispatcher's console to an accuracy of 50 feet. This gives the dispatcher a continuous picture of the deployment of the total available force and thus complete command and control of all police under his responsibility.

Review of Our National Heritage of Launch Vehicles Using Aerodynamic Surfaces and Current Use of These by Other Nations. Part II; Center Director's Discretionary Fund Project Numbe

NASA Technical Reports Server (NTRS)

Barret, C.

1996-01-01

Marshall Space Flight Center has a rich heritage of launch vehicles that have used aerodynamic surfaces for flight stability and for flight control. Recently, due to the aft center-of-gravity (cg) locations on launch vehicles currently being studied, the need has arisen for the vehicle control augmentation that can be provided by these flight controls. Aerodynamic flight control can also reduce engine gimbaling requirements, provide actuator failure protection, enhance crew safety, and increase vehicle reliability and payload capability. As a starting point for the novel design of aerodynamic flight control augmentors for a Saturn class, aft cg launch vehicle, this report undertakes a review of our national heritage of launch vehicles using aerodynamic surfaces, along with a survey of current use of aerodynamic surfaces on large launch vehicles of other nations. This report presents one facet of Center Director's Discretionary Fund Project 93-05 and has a previous and subsequent companion publication.

SKYLAB III - POSTLAUNCH (MISSION CONTROL CENTER [MCC]) - JSC

NASA Image and Video Library

1973-08-06

S73-31964 (5 August 1973) --- This group of flight controllers discuss today's approaching extravehicular activity (EVA) to be performed by the Skylab 3 crewmen. They are, left to right, scientist-astronaut Story Musgrave, a Skylab 3 spacecraft communicator; Robert Kain and Scott Millican, both of the Crew Procedures Division, EVA Procedures Section; William C. Schneider, Skylab Program Director, NASA Headquarters; and Milton Windler, flight director. Windler points to the model of the Skylab space station cluster to indicate the location of the ATM's film magazines. The group stands near consoles in the Mission Operations Control Room (MOCR) of the JSC Mission Control Center (MCC). Photo credit: NASA

47 CFR 25.280 - Inclined orbit operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of the Earth and centered on the satellite's designated service area; (2) Control all electrical... inclined orbit; and (4) Continue to maintain the space station at the authorized longitude orbital location...

Donation return time at fixed and mobile donation sites

PubMed Central

Carey, Patricia M.; High, Patrick M.; Schlumpf, Karen S.; Johnson, Bryce R.; Mast, Alan E.; Rios, Jorge A.; Simon, Toby L.; Wilkinson, Susan L.

2013-01-01

BACKGROUND This study investigated the effect of blood donation environment, fixed or mobile with differing sponsor types, on donation return time. STUDY DESIGN AND METHODS Data from 2006 through 2009 at six US blood centers participating in the Retrovirus Epidemiology Donor Study-II (REDS-II) were used for analysis. Descriptive statistics stratified by whole blood (WB), plateletpheresis (PP), and double red blood cell (R2) donations were obtained for fixed and mobile locations, including median number of donations and median interdonation interval. A survival analysis estimated median return time at fixed and mobile sites, while controlling for censored return times, demographics, blood center, and mandatory recovery times. RESULTS Two-thirds (67.9%) of WB donations were made at mobile sites, 97.4% of PP donations were made at fixed sites, and R2 donations were equally distributed between fixed and mobile locations. For donations at fixed sites only or alternating between fixed and mobile sites, the highest median numbers of donations were nine and eight, respectively, and the shortest model-adjusted median return times (controlling for mandatory eligibility times of 56 and 112 days) were 36 and 30 days for WB and R2 donations, respectively. For PP donations, the shortest model-adjusted median return time was 23 days at a fixed location and the longest was 693 days at community locations. CONCLUSION WB, PP, and R2 donors with the shortest time between donations were associated with fixed locations and those alternating between fixed and mobile locations, even after controlling for differing mandatory recovery times for the different blood donation procedures. PMID:21745215

Reducing lumber thickness variation using real-time statistical process control

Treesearch

Thomas M. Young; Brian H. Bond; Jan Wiedenbeck

2002-01-01

A technology feasibility study for reducing lumber thickness variation was conducted from April 2001 until March 2002 at two sawmills located in the southern U.S. A real-time statistical process control (SPC) system was developed that featured Wonderware human machine interface technology (HMI) with distributed real-time control charts for all sawing centers and...

Alternative Fuels Data Center: Biodiesel Fueling Station Locations

Science.gov Websites

Station Locations to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Fueling Station Locations on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Fueling Station Locations on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Fueling Station Locations on Google

Flight Research Center, Edwards, California. Environmental Impact Statement

NASA Technical Reports Server (NTRS)

1971-01-01

This is an institutional environmental impact statement relating to the overall operation of the NASA, Flight Research Center. The Center is located in Kern County, California, approximately 100 miles northeast of Los Angeles. Flight activities relate primarily to areas in the vicinity of Los Angeles, Kern, Inyo and San Bernardino counties in Southern California; and to areas in Southern Nevada (principally Nye and Clark counties. Operations of the Flight Research Center have a very neglibible impact on the environment; and they are planned and controlled to eliminate or minimize effects on water, air and noise.

Charting a Path to Location Intelligence for STD Control.

PubMed

Gerber, Todd M; Du, Ping; Armstrong-Brown, Janelle; McNutt, Louise-Anne; Coles, F Bruce

2009-01-01

This article describes the New York State Department of Health's GeoDatabase project, which developed new methods and techniques for designing and building a geocoding and mapping data repository for sexually transmitted disease (STD) control. The GeoDatabase development was supported through the Centers for Disease Control and Prevention's Outcome Assessment through Systems of Integrated Surveillance workgroup. The design and operation of the GeoDatabase relied upon commercial-off-the-shelf tools that other public health programs may also use for disease-control systems. This article provides a blueprint of the structure and software used to build the GeoDatabase and integrate location data from multiple data sources into the everyday activities of STD control programs.

KSC-LOC-63-5674

NASA Image and Video Library

1963-06-04

CAPE CANAVERAL, Fla. - Between 1962 and 1963, the Mission Control Center was modified to handle the additional complexities of the Gemini Program. In 1962, Pan American World Airways Inc. was contracted to design an addition to the facility, which wrapped around the east, north, and most of the west and south sides. The Mercury Mission Control Center in Florida played a key role in the United States' early spaceflight program. Located at Cape Canaveral Air Force Station, the original part of the building was constructed between 1956 and 1958, with additions in 1959 and 1963. The facility officially was transferred to NASA on Dec. 26, 1963, and served as mission control during all the Project Mercury missions, as well as the first three flights of the Gemini Program, when it was renamed Mission Control Center. With its operational days behind, on June 1, 1967, the Mission Control Center became a stop on the public tour of NASA facilities until the mid-90s. In 1999, much of the equipment and furnishings from the Flight Control Area were moved to the Kennedy Space Center Visitor Complex where they became part of the exhibit there. The building was demolished in spring 2010. Photo credit: NASA

KSC-LOC-63-1971

NASA Image and Video Library

1963-02-13

CAPE CANAVERAL, Fla. - Between 1962 and 1963, the Mission Control Center was modified to handle the additional complexities of the Gemini Program. In 1962, Pan American World Airways Inc. was contracted to design an addition to the facility, which wrapped around the east, north, and most of the west and south sides. The Mercury Mission Control Center in Florida played a key role in the United States' early spaceflight program. Located at Cape Canaveral Air Force Station, the original part of the building was constructed between 1956 and 1958, with additions in 1959 and 1963. The facility officially was transferred to NASA on Dec. 26, 1963, and served as mission control during all the Project Mercury missions, as well as the first three flights of the Gemini Program, when it was renamed Mission Control Center. With its operational days behind, on June 1, 1967, the Mission Control Center became a stop on the public tour of NASA facilities until the mid-90s. In 1999, much of the equipment and furnishings from the Flight Control Area were moved to the Kennedy Space Center Visitor Complex where they became part of the exhibit there. The building was demolished in spring 2010. Photo credit: NASA

KSC-LOC-63-1017

NASA Image and Video Library

1963-02-13

CAPE CANAVERAL, Fla. - Between 1962 and 1963, the Mission Control Center was modified to handle the additional complexities of the Gemini Program. In 1962, Pan American World Airways Inc. was contracted to design an addition to the facility, which wrapped around the east, north, and most of the west and south sides. The Mercury Mission Control Center in Florida played a key role in the United States' early spaceflight program. Located at Cape Canaveral Air Force Station, the original part of the building was constructed between 1956 and 1958, with additions in 1959 and 1963. The facility officially was transferred to NASA on Dec. 26, 1963, and served as mission control during all the Project Mercury missions, as well as the first three flights of the Gemini Program, when it was renamed Mission Control Center. With its operational days behind, on June 1, 1967, the Mission Control Center became a stop on the public tour of NASA facilities until the mid-90s. In 1999, much of the equipment and furnishings from the Flight Control Area were moved to the Kennedy Space Center Visitor Complex where they became part of the exhibit there. The building was demolished in spring 2010. Photo credit: NASA

KSC-LOC-63-5635

NASA Image and Video Library

1963-03-01

CAPE CANAVERAL, Fla. - Between 1962 and 1963, the Mission Control Center was modified to handle the additional complexities of the Gemini Program. In 1962, Pan American World Airways Inc. was contracted to design an addition to the facility, which wrapped around the east, north, and most of the west and south sides. The Mercury Mission Control Center in Florida played a key role in the United States' early spaceflight program. Located at Cape Canaveral Air Force Station, the original part of the building was constructed between 1956 and 1958, with additions in 1959 and 1963. The facility officially was transferred to NASA on Dec. 26, 1963, and served as mission control during all the Project Mercury missions, as well as the first three flights of the Gemini Program, when it was renamed Mission Control Center. With its operational days behind, on June 1, 1967, the Mission Control Center became a stop on the public tour of NASA facilities until the mid-90s. In 1999, much of the equipment and furnishings from the Flight Control Area were moved to the Kennedy Space Center Visitor Complex where they became part of the exhibit there. The building was demolished in spring 2010. Photo credit: NASA

KENNEDY SPACE CENTER, FLA. - Dr. Paul Hintze (left) explains to Center Director Jim Kennedy a project he is working at the KSC Beach Corrosion Test Site. Hitze is doing post-graduate work for the National Research Council. The test facility site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - Dr. Paul Hintze (left) explains to Center Director Jim Kennedy a project he is working at the KSC Beach Corrosion Test Site. Hitze is doing post-graduate work for the National Research Council. The test facility site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.207 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.207 Section 408.207 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... degree of effluent reduction attainable by the application of the best conventional pollutant control... processing facility located in population or processing centers including but not limited to Anchorage...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

40 CFR 408.297 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... control technology. 408.297 Section 408.297 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... of effluent reduction attainable by the application of the best conventional pollutant control... facility located in population or processing centers including but not limited to Anchorage, Cordova...

Publications - GMC 380 | Alaska Division of Geological & Geophysical

Science.gov Websites

Publications Geologic Materials Center General Information Inventory Monthly Report Hours and Location Policy DGGS GMC 380 Publication Details Title: 1974 control survey report for Orange Hill, Alaska Authors ): Nabesna Bibliographic Reference Smith, W.H., 2010, 1974 control survey report for Orange Hill, Alaska

78 FR 43817 - Distribution of Reference Biological Standards and Biological Preparations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-22

... and Prevention (CDC), Department of Health and Human Services (HHS). ACTION: Direct final rule and request for comments. SUMMARY: The Centers for Disease Control and Prevention (CDC), located within the... for Disease Control and Prevention, 1600 Clifton Road, NE., MS C-17, Atlanta, Georgia 30333, ATTN...

An Effective Massive Sensor Network Data Access Scheme Based on Topology Control for the Internet of Things.

PubMed

Yi, Meng; Chen, Qingkui; Xiong, Neal N

2016-11-03

This paper considers the distributed access and control problem of massive wireless sensor networks' data access center for the Internet of Things, which is an extension of wireless sensor networks and an element of its topology structure. In the context of the arrival of massive service access requests at a virtual data center, this paper designs a massive sensing data access and control mechanism to improve the access efficiency of service requests and makes full use of the available resources at the data access center for the Internet of things. Firstly, this paper proposes a synergistically distributed buffer access model, which separates the information of resource and location. Secondly, the paper divides the service access requests into multiple virtual groups based on their characteristics and locations using an optimized self-organizing feature map neural network. Furthermore, this paper designs an optimal scheduling algorithm of group migration based on the combination scheme between the artificial bee colony algorithm and chaos searching theory. Finally, the experimental results demonstrate that this mechanism outperforms the existing schemes in terms of enhancing the accessibility of service requests effectively, reducing network delay, and has higher load balancing capacity and higher resource utility rate.

Alternative Fuels Data Center: Ethanol Fueling Station Locations

Science.gov Websites

Fueling Station Locations to someone by E-mail Share Alternative Fuels Data Center: Ethanol Fueling Station Locations on Facebook Tweet about Alternative Fuels Data Center: Ethanol Fueling Station Locations on Twitter Bookmark Alternative Fuels Data Center: Ethanol Fueling Station Locations on Google

Simpler ISS Flight Control Communications and Log Keeping via Social Tools and Techniques

NASA Technical Reports Server (NTRS)

Scott, David W.; Cowart, Hugh; Stevens, Dan

2012-01-01

The heart of flight operations control involves a) communicating effectively in real time with other controllers in the room and/or in remote locations and b) tracking significant events, decisions, and rationale to support the next set of decisions, provide a thorough shift handover, and troubleshoot/improve operations. International Space Station (ISS) flight controllers speak with each other via multiple voice circuits or loops, each with a particular purpose and constituency. Controllers monitor and/or respond to several loops concurrently. The primary tracking tools are console logs, typically kept by a single operator and not visible to others in real-time. Information from telemetry, commanding, and planning systems also plays into decision-making. Email is very secondary/tertiary due to timing and archival considerations. Voice communications and log entries supporting ISS operations have increased by orders of magnitude because the number of control centers, flight crew, and payload operations have grown. This paper explores three developmental ground system concepts under development at Johnson Space Center s (JSC) Mission Control Center Houston (MCC-H) and Marshall Space Flight Center s (MSFC) Payload Operations Integration Center (POIC). These concepts could reduce ISS control center voice traffic and console logging yet increase the efficiency and effectiveness of both. The goal of this paper is to kindle further discussion, exploration, and tool development.

Reagan Test Site Distributed Operations

DTIC Science & Technology

2012-01-01

for missile testing because of its geography and its strategic location in the Pacific [ 1 ]. The atoll’s distance from launch facilities at Vandenberg...research on ballistic missile defense 50 years ago (Figure 1 ). The subsequent development of RTS’s unique instrumentation sensors, including high...control center including hardware, software, networks, and the facility functioned successfully. FIGURE 1 . The map shows the isolated location of the

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

This STS-98 Shuttle mission image shows an overall interior view of the newly attached U.S. Laboratory, Destiny. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-11

This STS-98 mission photograph shows astronauts Thomas D. Jones (foreground) and Kerneth D. Cockrell floating inside the newly installed Laboratory aboard the International Space Station (ISS). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

Location-Control of Large Si Grains by Dual-Beam Excimer-Laser and Thick Oxide Portion

NASA Astrophysics Data System (ADS)

Ishihara, Ryoichi; Burtsev, Artyom; Alkemade, Paul F. A.

2000-07-01

An array of large Si grains was placed at a predetermined position by dual excimer-laser irradiation of a multi-layer structure of silicon (Si), silicon dioxide (SiO2) with an array of bumps and metal on a glass substrate. We have investigated the effects of irradiating energy density and the topology of the structure on the grain size and crystallographic structure by scanning electron microscopy (SEM) and electron back-scattering pattern (EBSP) analysis. In the low-energy-density regime, numerous small grains and petal shaped grains formed on top of the SiO2 bumps. The number of small grains on the bumps decreased with increasing irradiating energy density. At sufficiently high energy densities, one single Si grain as large as 3.5 μm was positioned at the center of the bumps. Although most of the area of the large Si grain has a single crystallographic orientation, twins and low-angle grain boundaries are often formed at the periphery of the grain. There was no preferred crystallographic orientation in the center of the location-controlled Si grain. Numerical analysis of the temperature profile showed that a temperature drop occurs at the center of the bump, during and immediately after laser irradiation. The diameter of the location-controlled Si grain increased with total thickness of the intermediate SiO2 layer, and took the maximum value of 6.2 μm.

Radiological Control Center (RADCC) Renaming Ceremony

NASA Image and Video Library

2017-03-31

A Mars Science Laboratory cap is displayed in the Randall E. Scott Radiological Control Center at NASA's Kennedy Space Center. The facility was recently named in honor of Randy Scott, a professional health physicist of more than 40 years. He served as the Florida spaceport's Radiation Protection Officer for 14 years until his death June 17, 2016. Launched Nov. 26, 2011, the Mars Science Laboratory with the Curiosity lander was powered by a radioisotope thermalelectric generator. Located in the Neil Armstrong Operations and Checkout building, the Randall E. Scott Radiological Control Center is staffed by technical and radiological experts from NASA, the U.S. Department of Energy, the U.S. Air Force 45th Space Wing and the state of Florida. The group performs data collection and assessment functions supporting launch site and field data collection activities during launces involving plutonium-powered spacecraft such as the Mars Science Laboratory.

Biomechanical considerations for distraction of the monobloc, Le Fort III, and Le Fort I segments.

PubMed

Figueroa, Alvaro A; Polley, John W; Figueroa, Aaron D

2010-09-01

Distraction osteogenesis is effective for correction of severe maxillary and midface hypoplasia. The vectors controlling the segment to be moved must be planned. This requires knowledge of the physical characteristics of the osteotomized bone segment, including the location of the center of mass (free body) and the center of resistance (restrained body). The purpose of this study was to determine the center of mass of the osteotomized monobloc, Le Fort III, and Le Fort I bone segments. A dry human skull was used to sequentially isolate three bone segments: monobloc, Le Fort III, and Le Fort I. Each segment was suspended from three different points, and digital photographs were obtained from each suspension. The photographs were digitally superimposed. The center of mass was determined by calculating the intersection of the suspension lines. The center of mass for the monobloc segment was located at a point 43.5 percent of the total height from the occlusal plane to the superior edge of the frontal bone supraorbital osteotomy. For the Le Fort III, it was located 38 percent of the total height from the occlusal plane to the superior edge of the osteotomized base of the nasal bones. For the Le Fort I, it was 53 percent of the total height from the occlusal plane to the superior edge of the osteotomized maxillary bone. Knowledge of the location of the center of mass in the monobloc, Le Fort III, and Le Fort I segments provides a starting point for the clinician when planning vectors for advancement with distraction.

A novel device for head gesture measurement system in combination with eye-controlled human machine interface

NASA Astrophysics Data System (ADS)

Lin, Chern-Sheng; Ho, Chien-Wa; Chang, Kai-Chieh; Hung, San-Shan; Shei, Hung-Jung; Yeh, Mau-Shiun

2006-06-01

This study describes the design and combination of an eye-controlled and a head-controlled human-machine interface system. This system is a highly effective human-machine interface, detecting head movement by changing positions and numbers of light sources on the head. When the users utilize the head-mounted display to browse a computer screen, the system will catch the images of the user's eyes with CCD cameras, which can also measure the angle and position of the light sources. In the eye-tracking system, the program in the computer will locate each center point of the pupils in the images, and record the information on moving traces and pupil diameters. In the head gesture measurement system, the user wears a double-source eyeglass frame, so the system catches images of the user's head by using a CCD camera in front of the user. The computer program will locate the center point of the head, transferring it to the screen coordinates, and then the user can control the cursor by head motions. We combine the eye-controlled and head-controlled human-machine interface system for the virtual reality applications.

Radar Training Facility initial validation.

DOT National Transportation Integrated Search

1983-05-01

The Radar Training Facility (RTF), part of the Federal Aviation Administration Academy located at the Oklahoma City Mike Monroney Aeronautical Center, is designed to identify, as early as possible, air traffic control specialists who do not demonstra...

77 FR 12845 - Centers for Disease Control and Prevention (CDC)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

... announced below concerns Green Housing Study: Follow-up Measurements of Housing Factors and Respiratory... Respiratory Health of Children Located in Cincinnati and Boston (U01), FOA EH12-001.'' Contact Person for More...

Job Grading Standard for Electric Power Controller WG-5407.

ERIC Educational Resources Information Center

Civil Service Commission, Washington, DC. Bureau of Policies and Standards.

The standard is used to grade nonsupervisory jobs involved in controlling the generation or distribution of electric power. The jobs are located at power generating plants, power distribution centers, and substations. The work requires ability to anticipate load changes due to work schedules, weather, and other variables, in order to engage or cut…

Leveraging Executable Architectures in a Joint Environment

DTIC Science & Technology

2009-01-01

Support of Type 2/3 Terminal Attack Control Call Wing Operations Center (WOC) to Task On-Call Aircraft Call Air Command and Control Agency ( ACCA ) to...MIDS MIDS MIDS X = Existing capability P1 = Partial - requires voice ack P2 = Partial - only some F/A-18s None P3 = remarks only TARGET LOCATION

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

40 CFR 408.167 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... control technology. 408.167 Section 408.167 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... control technology. (a) [Reserved] (b) Except as provided in §§ 125.30 through 125.32, any hand-butchered salmon processing facility located in population or processing centers including but not limited to...

Self-Blame in Rape Victims: A Control-Maintenance Strategy.

ERIC Educational Resources Information Center

Janoff-Bulman, Ronnie

Two types of self-blame were investigated: characterological self-blame, corresponding to the popular negative view of self-blame; and behavioral self-blame, representing a positive attempt to reestablish a belief in control. Results of a questionnaire completed by rape crisis centers located across the country attest to the pervasiveness of…

An Overview Of The National Institute For Occupational Safety And Health (NIOSH) Activity In Nonionizing Radiation

NASA Astrophysics Data System (ADS)

Moss, C. Eugene

1980-10-01

The National Institute for Occupational Safety and Health (NIOSH) is a major component of the Center for Disease Control in the Department of Health, Education, and Welfare (DHEW). Headquarters for NIOSH are located in Rockville, Maryland, with laboratory facilities in Morgantown, West Virginia and Cincinnati, Ohio. NIOSH has approximately 900 employees with about 60% located in Cincinnati.

Advanced wind turbine with lift cancelling aileron for shutdown

DOEpatents

Coleman, Clint; Juengst, Theresa M.; Zuteck, Michael D.

1996-06-18

An advanced aileron configuration for wind turbine rotors featuring an independent, lift generating aileron connected to the rotor blade. The aileron has an airfoil profile which is inverted relative to the airfoil profile of the main section of the rotor blade. The inverted airfoil profile of the aileron allows the aileron to be used for strong positive control of the rotation of the rotor while deflected to angles within a control range of angles. The aileron functions as a separate, lift generating body when deflected to angles within a shutdown range of angles, generating lift with a component acting in the direction opposite the direction of rotation of the rotor. Thus, the aileron can be used to shut down rotation of the rotor. The profile of the aileron further allows the center of rotation to be located within the envelope of the aileron, at or near the centers of pressure and mass of the aileron. The location of the center of rotation optimizes aerodynamically and gyroscopically induced hinge moments and provides a fail safe configuration.

Influences of posterior-located center of gravity on lumbar extension strength, balance, and lumbar lordosis in chronic low back pain.

PubMed

Kim, Dae-Hun; Park, Jin-Kyu; Jeong, Myeong-Kyun

2014-01-01

In patients with chronic low back pain, the center of gravity (COG) is abnormally located posterior to the center in most cases. The purpose of this study was to examine the effects of posterior-located COG on the functions (lumbar extension strength, and static and dynamic balance) and structure (lumbar lordosis angle and lumbosacral angle) of the lumbar spine. In this study, the COG of chronic low back pain patients who complained of only low back pain were examined using dynamic body balance equipment. A total of 164 subjects participated in the study (74 males and 90 females), and they were divided into two groups of 82 patients each. One group (n=82) consisted of patients whose COG was located at the center (C-COG); the other group (n=82) consisted of patients whose COG was located posterior to the center (P-COG). The following measures assessed the lumber functions and structures of the two groups: lumbar extension strength, moving speed of static and dynamic COGs, movement distance of the static and dynamic COGs, lumbar lordosis angle, and lumbosacral angle. The measured values were analyzed using independent t-tests. The group of patients with P-COG showed more decreases in lumbar extension strength, lumbar lordosis angle, and lumbosacral angle compared to the group of patients with C-COG. Also this group showed increases in moving speed and movement distance of the static COG. However, there were no differences in moving speed and movement distance of the dynamic COG between the two groups. These findings suggest that chronic LBP patients with P-COG have some disadvantages to establish lumbar extension strength and static and dynamic balance, which require specific efforts to maintain a neutral position and to control posture.

Alternative Fuels Data Center: Electric Vehicle Charging Station Locations

Science.gov Websites

Electric Vehicle Charging Station Locations to someone by E-mail Share Alternative Fuels Data Center: Electric Vehicle Charging Station Locations on Facebook Tweet about Alternative Fuels Data Center : Electric Vehicle Charging Station Locations on Twitter Bookmark Alternative Fuels Data Center: Electric

Alternative Fuels Data Center: Alternative Fueling Station Locator

Science.gov Websites

Locate Stations Printable Version Share this resource Send a link to Alternative Fuels Data Center : Alternative Fueling Station Locator to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuels Data Center: Alternative Fueling Station Locator on Digg Find More places to share Alternative

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

The Payload Operations Center (POC) is the science command post for the International Space Station (ISS). Located at NASA's Marshall Space Flight Center in Huntsville, Alabama, it is the focal point for American and international science activities aboard the ISS. The POC's unique capabilities allow science experts and researchers around the world to perform cutting-edge science in the unique microgravity environment of space. The POC is staffed around the clock by shifts of payload flight controllers. At any given time, 8 to 10 flight controllers are on consoles operating, plarning for, and controlling various systems and payloads. This photograph shows the Timeline Change Officer (TCO) at a work station. The TCO maintains the daily schedule of science activities and work assignments, and works with planners at Mission Control at Johnson Space Center in Houston, Texas, to ensure payload activities are accommodated in overall ISS plans and schedules.

STS-112 crew with President of Ajara in Georgia (Russia)

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- Aslan Abashidze, President of the Autonomous Republic of Ajara in Georgia (Russia) shakes hands with STS-112 Mission Specialist Fyodor N. Yurchikhin, Ph.D., (right) a cosmonaut with the Russian Space Agency. Yurchikhin is at Kennedy Space Center awaiting his launch aboard Space Shuttle Atlantis on mission STS-112 to the International Space Station. The launch has been postponed to no earlier than Monday, Oct. 7, so that the Mission Control Center, located at the Lyndon B. Johnson Space Center in Houston, Texas, can be secured and protected from potential storm impacts from Hurricane Lili.

Metal Building Insulation System Provides Energy Savings and Noise Control.

ERIC Educational Resources Information Center

School Business Affairs, 1979

1979-01-01

Thermal efficiency increased substantially when an underdeck metal building insulation system was used at the North Valley Occupational Center, an aircraft mechanic's school located at the edge of the Van Nuys, California, airport. (Author)

An Effective Massive Sensor Network Data Access Scheme Based on Topology Control for the Internet of Things

PubMed Central

Yi, Meng; Chen, Qingkui; Xiong, Neal N.

2016-01-01

This paper considers the distributed access and control problem of massive wireless sensor networks’ data access center for the Internet of Things, which is an extension of wireless sensor networks and an element of its topology structure. In the context of the arrival of massive service access requests at a virtual data center, this paper designs a massive sensing data access and control mechanism to improve the access efficiency of service requests and makes full use of the available resources at the data access center for the Internet of things. Firstly, this paper proposes a synergistically distributed buffer access model, which separates the information of resource and location. Secondly, the paper divides the service access requests into multiple virtual groups based on their characteristics and locations using an optimized self-organizing feature map neural network. Furthermore, this paper designs an optimal scheduling algorithm of group migration based on the combination scheme between the artificial bee colony algorithm and chaos searching theory. Finally, the experimental results demonstrate that this mechanism outperforms the existing schemes in terms of enhancing the accessibility of service requests effectively, reducing network delay, and has higher load balancing capacity and higher resource utility rate. PMID:27827878

14 CFR 1206.401 - Location of NASA Information Centers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 5 2012-01-01 2012-01-01 false Location of NASA Information Centers. 1206... § 1206.401 Location of NASA Information Centers. (a) NASA will maintain the following Information Centers... which copies of Agency forms may be obtained: (1) NASA Headquarters (HQ) Information Center, National...

14 CFR 1206.401 - Location of NASA Information Centers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 5 2013-01-01 2013-01-01 false Location of NASA Information Centers. 1206... § 1206.401 Location of NASA Information Centers. (a) NASA will maintain the following Information Centers... which copies of Agency forms may be obtained: (1) NASA Headquarters (HQ) Information Center, National...

14 CFR 1206.401 - Location of NASA Information Centers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Location of NASA Information Centers. 1206... § 1206.401 Location of NASA Information Centers. (a) NASA will maintain the following Information Centers... which copies of Agency forms may be obtained: (1) NASA Headquarters (HQ) Information Center, National...

14 CFR 1206.401 - Location of NASA Information Centers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Location of NASA Information Centers. 1206... § 1206.401 Location of NASA Information Centers. (a) NASA will maintain the following Information Centers... which copies of Agency forms may be obtained: (1) NASA Headquarters (HQ) Information Center, National...

KSC-04pd1730

NASA Image and Video Library

2004-09-08

KENNEDY SPACE CENTER, FLA. - The work to clean up and secure the roof of the Processing Control Center which sustained damage from Hurricane Frances is under way. The storm's path over Florida took it through Cape Canaveral and KSC property during Labor Day weekend. Located in Launch Complex 39, the facility houses some of the staff and computers responsible for Launch Processing System (LPS) software development, launch team training, and LPS maintenance.

KSC-04pd1731

NASA Image and Video Library

2004-09-08

KENNEDY SPACE CENTER, FLA. - KSC employees secure the roof of the Processing Control Center which sustained damage from Hurricane Frances. The storm's path over Florida took it through Cape Canaveral and KSC property during Labor Day weekend. Located in Launch Complex 39 adjacent to the Vehicle Assembly Building (background right), the facility houses some of the staff and computers responsible for Launch Processing System (LPS) software development, launch team training, and LPS maintenance.

KSC-04pd1729

NASA Image and Video Library

2004-09-08

KENNEDY SPACE CENTER, FLA. - KSC employees begin the work to clean up and secure the roof of the Processing Control Center which sustained damage from Hurricane Frances. The storm's path over Florida took it through Cape Canaveral and KSC property during Labor Day weekend. Located in Launch Complex 39, the facility houses some of the staff and computers responsible for Launch Processing System (LPS) software development, launch team training, and LPS maintenance.

73. VIEW OF LAUNCH OPERATOR AND LAUNCH ANAYLST PANELS LOCATED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

73. VIEW OF LAUNCH OPERATOR AND LAUNCH ANAYLST PANELS LOCATED NEAR CENTER OF SOUTH WALL OF SLC-3E CONTROL ROOM. FROM LEFT TO RIGHT ON WALL IN BACKGROUND: COMMUNICATIONS HEADSET AND FOOT PEDAL IN FORGROUND. ACCIDENT REPORTING EMERGENCY NOTIFICATION SYSTEM TELEPHONE, ATLAS H FUEL COUNTER, AND DIGITAL COUNTDOWN CLOCK. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Operations Building, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

An investigation of the effects of touchpad location within a notebook computer.

PubMed

Kelaher, D; Nay, T; Lawrence, B; Lamar, S; Sommerich, C M

2001-02-01

This study evaluated effects of the location of a notebook computer's integrated touchpad, complimenting previous work in the area of desktop mouse location effects. Most often integrated touchpads are located in the computer's wrist rest, and centered on the keyboard. This study characterized effects of this bottom center location and four alternatives (top center, top right, right side, and bottom right) upon upper extremity posture, discomfort, preference, and performance. Touchpad location was found to significantly impact each of those measures. The top center location was particularly poor, in that it elicited more ulnar deviation, more shoulder flexion, more discomfort, and perceptions of performance impedance. In general, the bottom center, bottom right, and right side locations fared better, though subjects' wrists were more extended in the bottom locations. Suggestions for notebook computer design are provided.

STS-40 crew trains in JSC's SLS mockup located in Bldg 36

NASA Image and Video Library

1987-03-10

STS-40 Payload Specialist Millie Hughes-Fulford along with backup payload specialist Robert Ward Phillips familiarize themselves with Spacelab Life Sciences 1 (SLS-1) equipment. The two scientists are in JSC's Life Sciences Project Division (LSPD) SLS mockup located in the Bioengineering and Test Support Facility Bldg 36. Hughes-Fulford, in the center aisle, pulls equipment from an overhead stowage locker while Phillips, in the foreground, experiments with the baroreflex neck pressure chamber at Rack 11. The baroreflex collar will be used in conjuction with Experiment No. 022, Influence of Weightlessness Upon Human Autonomic Cardiovascular Control. Behind Phillips in the center aisle are body mass measurement device (BMMD) (foreground) and the stowed bicycle ergometer.

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

This STS-98 mission photograph shows astronauts Thomas D. Jones (foreground) and Kerneth D. Cockrell floating inside the newly installed Laboratory aboard the International Space Station (ISS). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

This closer image of the International Space Station (ISS) showing the newly installed U.S. Laboratory, Destiny (left), was taken from the departing Space Shuttle Atlantis. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

Remote-area health care delivery through space technology - STARPAHC

NASA Technical Reports Server (NTRS)

Belasco, N.; Johnston, R. S.; Stonesifer, J. C.; Pool, S. L.

1977-01-01

A joint NASA/HEW project called Space Technology Applied to Rural Papage Advanced Health Care (STARPAHC) has been developed to deliver quality health care to inhabitants of remote geographical areas. The system consists of a hospital-based support control center, a fixed clinic, a mobile clinic, and a referral center with access to specialists via television links to the control center. A strategically located relay station routes television, voice, and data transmissions between system elements. A model system has been installed on the Papage Indian Reservation in Arizona, and is undergoing a 2-year evaluation. The system has been shown to be both effective and cost-efficient, and applications of the concept are planned for future manned spacecraft flights.

14 CFR § 1206.401 - Location of NASA Information Centers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 5 2014-01-01 2014-01-01 false Location of NASA Information Centers. Â... § 1206.401 Location of NASA Information Centers. (a) NASA will maintain the following Information Centers... which copies of Agency forms may be obtained: (1) NASA Headquarters (HQ) Information Center, National...

Technique for controlling shrinkage distortion in cold-pressed annular pellets

DOEpatents

Johnson, R.G.R.; Burke, T.J.

1982-06-28

A process and apparatus are described for the production of annular fuel pellets comprising locating particulate fuel material in a compaction chamber having side walls, a moveable punch located opposite a fixed member and a frustoconical element having a taper of between about 0.010 to 0.015 inches/inch located in about the center of the chamber. The punch is moved toward the fixed surface to compact the particulate material. The compacted pellet is fired to produce sintered pellets having substantially straight inner side walls essentially parallel to the pellet axis.

Canadarm2 Maneuvers Quest Airlock

NASA Technical Reports Server (NTRS)

2001-01-01

At the control of Expedition Two Flight Engineer Susan B. Helms, the newly-installed Canadian-built Canadarm2, Space Station Remote Manipulator System (SSRMS) maneuvers the Quest Airlock into the proper position to be mated onto the starboard side of the Unity Node I during the first of three extravehicular activities (EVA) of the STS-104 mission. The Quest Airlock makes it easier to perform space walks, and allows both Russian and American spacesuits to be worn when the Shuttle is not docked with the International Space Station (ISS). American suits will not fit through Russion airlocks at the Station. The Boeing Company, the space station prime contractor, built the 6.5-ton (5.8 metric ton) airlock and several other key components at the Marshall Space Flight Center (MSFC), in the same building where the Saturn V rocket was built. Installation activities were supported by the development team from the Payload Operations Control Center (POCC) located at the MSFC and the Mission Control Center at NASA's Johnson Space Flight Center in Houston, Texas.

International Space Station (ISS)

NASA Image and Video Library

2001-07-15

At the control of Expedition Two Flight Engineer Susan B. Helms, the newly-installed Canadian-built Canadarm2, Space Station Remote Manipulator System (SSRMS) maneuvers the Quest Airlock into the proper position to be mated onto the starboard side of the Unity Node I during the first of three extravehicular activities (EVA) of the STS-104 mission. The Quest Airlock makes it easier to perform space walks, and allows both Russian and American spacesuits to be worn when the Shuttle is not docked with the International Space Station (ISS). American suits will not fit through Russion airlocks at the Station. The Boeing Company, the space station prime contractor, built the 6.5-ton (5.8 metric ton) airlock and several other key components at the Marshall Space Flight Center (MSFC), in the same building where the Saturn V rocket was built. Installation activities were supported by the development team from the Payload Operations Control Center (POCC) located at the MSFC and the Mission Control Center at NASA's Johnson Space Flight Center in Houston, Texas.

Fuel management system for cruise performance optimization on a large blended wing body airliner

NASA Astrophysics Data System (ADS)

Wildschek, A.; Stroscher, F.; Haniš, T.; Belschner, T.

2013-12-01

Blended Wing Body (BWB) aircraft configurations have been proposed for significant fuel efficiency improvement on commercial transport. In order to fly with the optimum lift-to-drag ratio throughout most of the mission, an adaptation of the center of gravity (CG) by fuel redistribution is proposed. The most aft location of the CG which still is controllable is mainly limited by actuator bandwidth whereas the front CG location is limited by control authority of the trailing edge control surfaces. This paper provides an optimization of the CG position with regards to minimization of fuel consumption. Layout of the fuel tank system is illustrated. Moreover, active stabilization of faulty CG positions is discussed.

Neuroendokrine Regulationsmechanismen

NASA Astrophysics Data System (ADS)

Wuttke, Wolfgang

1980-06-01

The main center for the control of sexual functions is located in the hypothalamus. The medial preoptic area and the mediobasal hypothalamus are sites of production of neuropeptides which are released into the hypothalamo-pituitary portal vessel system and which function as releasing and inhibiting hormones.

The radiative decays of excited states of transition elements located inside and near core-shell nanoparticles

NASA Astrophysics Data System (ADS)

Pukhov, Konstantin K.

2017-12-01

Here we discuss the radiative decays of excited states of transition elements located inside and outside of the subwavelength core-shell nanoparticles embedded in dielectric medium. Based on the quantum mechanics and quantum electrodynamics, the general analytical expressions are derived for the probability of the spontaneous transitions in the luminescent centers (emitter) inside and outside the subwavelength core-shell nanoparticle. Obtained expressions holds for arbitrary orientation of the dipole moment and the principal axes of the quadrupole moment of the emitter with respect to the radius-vector r connecting the center of the emitter with the center of the nanoparticle. They have simple form and show how the spontaneous emission in core-shell NPs can be controlled and engineered due to the dependence of the emission rates on core-shell sizes, radius-vector r and permittivities of the surrounding medium, shell, and core.

KSC-02pd1417

NASA Image and Video Library

2002-10-01

KENNEDY SPACE CENTER, FLA. - STS-112 Commander Jeffrey S. Ashby poses in front of Launch Pad 39B during a tour of Kennedy Space Center prior to launch. Also on the tour were the other members of the crew including Pilot Pamela Ann Melroy and Mission Specialists David A. Wolf, Sandra H. Magnus, Piers J. Sellers, and Fyodor N. Yurchikhin of the Russian Space Agency. The launch of Space Shuttle Atlantis was postponed today to no earlier than Thursday, Oct. 3, while weather forecasters and the mission management team assess the possible effect Hurricane Lili may have on the Mission Control Center located at the Lyndon B. Johnson Space Center in Houston, Texas.

KSC-02pd1416

NASA Image and Video Library

2002-10-01

KENNEDY SPACE CENTER, FLA. - Members of the STS-112 crew pose in front of Launch Pad 39B during a tour of Kennedy Space Center prior to launch. From left, they are Mission Specialist Sandra H. Magnus, Commander Jeffrey S. Ashby, Pilot Pamela Ann Melroy, and Mission Specialists David A. Wolf, Fyodor N. Yurchikhin of the Russian Space Agency, and Piers J. Sellers. The launch of Space Shuttle Atlantis was postponed today to no earlier than Thursday, Oct. 3, while weather forecasters and the mission management team assess the possible effect Hurricane Lili may have on the Mission Control Center located at the Lyndon B. Johnson Space Center in Houston, Texas.

A global spacecraft control network for spacecraft autonomy research

NASA Technical Reports Server (NTRS)

Kitts, Christopher A.

1996-01-01

The development and implementation of the Automated Space System Experimental Testbed (ASSET) space operations and control network, is reported on. This network will serve as a command and control architecture for spacecraft operations and will offer a real testbed for the application and validation of advanced autonomous spacecraft operations strategies. The proposed network will initially consist of globally distributed amateur radio ground stations at locations throughout North America and Europe. These stations will be linked via Internet to various control centers. The Stanford (CA) control center will be capable of human and computer based decision making for the coordination of user experiments, resource scheduling and fault management. The project's system architecture is described together with its proposed use as a command and control system, its value as a testbed for spacecraft autonomy research, and its current implementation.

76 FR 1195 - Privacy Act System of Records Notice (11-001)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-07

... Aeronautics and Space Administration Washington, DC 20546-0001 Location 2 Ames Research Center, National Aeronautics and Space Administration, Moffett Field, CA 94035-1000 Location 3 Dryden Flight Research Center... Center, FL 32899-0001 Location 7 Langley Research Center, National Aeronautics and Space Administration...

Efficacy of agricultural oil and fungicide combinations as a late dormant treatment for control of peach scab in Alabama, 2016

USDA-ARS?s Scientific Manuscript database

Fungicides were evaluated for control of scab in a mid-ripening peach experimental block (‘Ruston Red’) located at the Chilton Area Research and Extension Center in Clanton, AL. Chemical formulations were applied with an airblast sprayer (112.5 gal/A spray volume). Treatment regimens included a non-...

Large robotized turning centers described

NASA Astrophysics Data System (ADS)

Kirsanov, V. V.; Tsarenko, V. I.

1985-09-01

The introduction of numerical control (NC) machine tools has made it possible to automate machining in series and small series production. The organization of automated production sections merged NC machine tools with automated transport systems. However, both the one and the other require the presence of an operative at the machine for low skilled operations. Industrial robots perform a number of auxiliary operations, such as equipment loading-unloading and control, changing cutting and auxiliary tools, controlling workpieces and parts, and cleaning of location surfaces. When used with a group of equipment they perform transfer operations between the machine tools. Industrial robots eliminate the need for workers to form auxiliary operations. This underscores the importance of developing robotized manufacturing centers providing for minimal human participation in production and creating conditions for two and three shift operation of equipment. Work carried out at several robotized manufacturing centers for series and small series production is described.

Dynamic test results for the CASES ground experiment

NASA Technical Reports Server (NTRS)

Bukley, Angelia P.; Patterson, Alan F.; Jones, Victoria L.

1993-01-01

The Controls, Astrophysics, and Structures Experiment in Space (CASES) Ground Test Facility (GTF) has been developed at Marshall Space Flight Center (MSFC) to provide a facility for the investigation of Controls/Structures Interaction (CSI) phenomena, to support ground testing of a potential shuttle-based CASES flight experiment, and to perform limited boom deployment and retraction dynamics studies. The primary objectives of the ground experiment are to investigate CSI on a test article representative of a Large Space Structure (LSS); provide a platform for Guest Investigators (GI's) to conduct CSI studies; to test and evaluate LSS control methodologies, system identification (ID) techniques, failure mode analysis; and to compare ground test predictions and flight results. The proposed CASES flight experiment consists of a 32 meter deployable/retractable boom at the end of which is an occulting plate. The control objective of the experiment is to maintain alignment of the tip plate (occulter) with a detector located at the base of the boom in the orbiter bay. The tip plate is pointed towards a star, the sun, or the galactic center to collect high-energy X-rays emitted by these sources. The tip plate, boom, and detector comprise a Fourier telescope. The occulting holes in the tip plate are approximately one millimeter in diameter making the alignment requirements quite stringent. Control authority is provided by bidirectional linear thrusters located at the boom tip and Angular Momentum Exchange Devices (AMED's) located at mid-boom and at the tip. The experiment embodies a number of CSI control problems including vibration suppression, pointing a long flexible structure, and disturbance rejection. The CASES GTF is representative of the proposed flight experiment with identical control objectives.

Alternative Fuels Data Center: Hydrogen Fueling Station Locations

Science.gov Websites

Hydrogen Printable Version Share this resource Send a link to Alternative Fuels Data Center : Hydrogen Fueling Station Locations to someone by E-mail Share Alternative Fuels Data Center: Hydrogen Fuels Data Center: Hydrogen Fueling Station Locations on Digg Find More places to share Alternative

42 CFR 478.18 - Location for submitting requests for reconsideration.

Code of Federal Regulations, 2010 CFR

2010-10-01

... reconsideration. 478.18 Section 478.18 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS RECONSIDERATIONS AND APPEALS Utilization and Quality Control Quality Improvement Organization (QIO) Reconsiderations and Appeals § 478.18...

The Quality Control Algorithms Used in the Process of Creating the NASA Kennedy Space Center Lightning Protection System Towers Meteorological Database

NASA Technical Reports Server (NTRS)

Orcutt, John M.; Brenton, James C.

2016-01-01

The methodology and the results of the quality control (QC) process of the meteorological data from the Lightning Protection System (LPS) towers located at Kennedy Space Center (KSC) launch complex 39B (LC-39B) are documented in this paper. Meteorological data are used to design a launch vehicle, determine operational constraints, and to apply defined constraints on day-of-launch (DOL). In order to properly accomplish these tasks, a representative climatological database of meteorological records is needed because the database needs to represent the climate the vehicle will encounter. Numerous meteorological measurement towers exist at KSC; however, the engineering tasks need measurements at specific heights, some of which can only be provided by a few towers. Other than the LPS towers, Tower 313 is the only tower that provides observations up to 150 m. This tower is located approximately 3.5 km from LC-39B. In addition, data need to be QC'ed to remove erroneous reports that could pollute the results of an engineering analysis, mislead the development of operational constraints, or provide a false image of the atmosphere at the tower's location.

General view of a Space Shuttle Main Engine (SSME) mounted ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of a Space Shuttle Main Engine (SSME) mounted on an SSME engine handler, taken in the SSME Processing Facility at Kennedy Space Center. The most prominent features of the engine assembly in this view are the Low-Pressure Fuel Turbopump Discharge Duct looping around the right side and underneath the assembly, the High-Pressure Fuel Turbopump located on the lower left portion of the assembly, the Engine Controller and Main Fuel Valve Hydraulic Actuator located on the upper portion of the assembly and the Low-Pressure Oxidizer Turbopump Discharge Duct at the top of the engine assembly in this view. - Space Transportation System, Space Shuttle Main Engine, Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

The USGS National Wildlife Health Center: Advancing wildlife and ecosystem health

USGS Publications Warehouse

Moede Rogall, Gail; Sleeman, Jonathan M.

2017-01-11

In 1975, the Federal government responded to the need for establishing national expertise in wildlife health by creating the National Wildlife Health Center (NWHC), a facility within the Department of the Interior; the NWHC is the only national center dedicated to wildlife disease detection, control, and prevention. Its mission is to provide national leadership to safeguard wildlife and ecosystem health through active partnerships and exceptional science. Comparisons are often made between the NWHC, which strives to protect the health of our Nation’s wildlife, and the Centers for Disease Control and Prevention (CDC), which strive to protect public health. The NWHC, a science center of the U.S. Geological Survey (USGS) with specialized laboratories, works to safeguard the Nation’s wildlife from diseases by studying the causes and drivers of these threats, and by developing strategies to prevent and manage them. In addition to the main campus, located in Madison, Wisconsin, the NWHC also operates the Honolulu Field Station that addresses wildlife health issues in Hawaii and the Pacific Region.

Research on Using the Naturally Cold Air and the Snow for Data Center Air-conditioning, and Humidity Control

NASA Astrophysics Data System (ADS)

Tsuda, Kunikazu; Tano, Shunichi; Ichino, Junko

To lower power consumption has becomes a worldwide concern. It is also becoming a bigger area in Computer Systems, such as reflected by the growing use of software-as-a-service and cloud computing whose market has increased since 2000, at the same time, the number of data centers that accumulates and manages the computer has increased rapidly. Power consumption at data centers is accounts for a big share of the entire IT power usage, and is still rapidly increasing. This research focuses on the air-conditioning that occupies accounts for the biggest portion of electric power consumption by data centers, and proposes to develop a technique to lower the power consumption by applying the natural cool air and the snow for control temperature and humidity. We verify those effectiveness of this approach by the experiment. Furthermore, we also examine the extent to which energy reduction is possible when a data center is located in Hokkaido.

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

The Payload Operations Center (POC) is the science command post for the International Space Station (ISS). Located at NASA's Marshall Space Flight Center in Huntsville, Alabama, it is the focal point for American and international science activities aboard the ISS. The POC's unique capabilities allow science experts and researchers around the world to perform cutting-edge science in the unique microgravity environment of space. The POC is staffed around the clock by shifts of payload flight controllers. At any given time, 8 to 10 flight controllers are on consoles operating, plarning for, and controlling various systems and payloads. This photograph shows the Operations Controllers (OC) at their work stations. The OC coordinates the configuration of resources to enable science operations, such as power, cooling, commanding, and the availability of items like tools and laboratory equipment.

Development of a two-dimensional skin friction balance nulling circuit using multivariable control theory

NASA Technical Reports Server (NTRS)

Tripp, John S.; Patek, Stephen D.

1988-01-01

Measurement of planar skin friction forces in aerodynamic testing currently requires installation of two perpendicularly mounted, single-axis balances; consequently, force components must be sensed at two distinct locations. A two-axis instrument developed at the Langley Research Center to overcome this disadvantage allows measurement of a two-dimensional force at one location. This paper describes a feedback-controlled nulling circuit developed for the NASA two-axis balance which, without external compensation, is inherently unstable because of its low friction mechanical design. Linear multivariable control theory is applied to an experimentally validated mathematical model of the balance to synthesize a state-variable feedback control law. Pole placement techniques and computer simulation studies are employed to select eigenvalues which provide ideal transient response with decoupled sensing dynamics.

13 CFR 130.320 - Location of lead centers and SBDC service providers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Location of lead centers and SBDC service providers. 130.320 Section 130.320 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS DEVELOPMENT CENTERS § 130.320 Location of lead centers and SBDC service providers. (a...

13 CFR 130.320 - Location of lead centers and SBDC service providers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Location of lead centers and SBDC service providers. 130.320 Section 130.320 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS DEVELOPMENT CENTERS § 130.320 Location of lead centers and SBDC service providers. (a...

Sexual Violence Screening Practices of Student Health Centers Located on Universities in Florida

ERIC Educational Resources Information Center

Halstead, Valerie; Williams, Jessica R.; Gattamorta, Karina; Gonzalez-Guarda, Rosa

2017-01-01

Objective: The purpose of this study is to describe current sexual violence screening practices of student health centers located on universities in Florida. Participants: Institutional level data was collected from 33 student health centers from November 2015 through January 2016. The student health centers were located on public or private…

KSC-03pd0844

NASA Image and Video Library

2003-03-26

KENNEDY SPACE CENTER, FLA. - Workers in the KSC Launch Control Center look at the printout from Columbia's Orbiter Experiment Support System (OEX) recorder. After duplication the tape will be reviewed at the Johnson Space Center in Houston and other facilities. No actual sensor data on that tape has been reviewed at this time. Search teams near Hemphill, Texas recovered the recorder, which stores sensor information about temperature, aerodynamic pressure, vibrations and other data from dozens of sensor locations on the orbiter, operating only during launch and re-entry. The OEX uses magnetic tape to record data that is not sent to the ground by telemetry.

KSC-03pd0842

NASA Image and Video Library

2003-03-26

KENNEDY SPACE CENTER, FLA. - Workers in the KSC Launch Control Center watch the taping operation involving Columbia's Orbiter Experiment Support System (OEX) recorder. After duplication the tape will be reviewed at the Johnson Space Center in Houston and other facilities. No actual sensor data on that tape has been reviewed at this time. Search teams near Hemphill, Texas recovered the recorder, which stores sensor information about temperature, aerodynamic pressure, vibrations and other data from dozens of sensor locations on the orbiter, operating only during launch and re-entry. The OEX uses magnetic tape to record data that is not sent to the ground by telemetry.

KSC-03pd0841

NASA Image and Video Library

2003-03-26

KENNEDY SPACE CENTER, FLA. -- Columbia's Orbiter Experiment Support System (OEX) recorder is put on taping equipment in the KSC Launch Control Center. The recorder tape is being duplicated and will be reviewed at the Johnson Space Center in Houston and other facilities. No actual sensor data on that tape has been reviewed at this time, Search teams near Hemphill, Texas recovered the recorder, which stores sensor information about temperature, aerodynamic pressure, vibrations and other data from dozens of sensor locations on the orbiter, operating only during launch and re-entry. The OEX uses magnetic tape to record data that is not sent to the ground by telemetry.

KSC-03pd0843

NASA Image and Video Library

2003-03-26

KENNEDY SPACE CENTER, FLA. - Workers in the KSC Launch Control Center look at the printout from Columbia's Orbiter Experiment Support System (OEX) recorder. After duplication the tape will be reviewed at the Johnson Space Center in Houston and other facilities. No actual sensor data on that tape has been reviewed at this time. Search teams near Hemphill, Texas recovered the recorder, which stores sensor information about temperature, aerodynamic pressure, vibrations and other data from dozens of sensor locations on the orbiter, operating only during launch and re-entry. The OEX uses magnetic tape to record data that is not sent to the ground by telemetry.

Complete data listings for CSEM soundings on Kilauea Volcano, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kauahikaua, J.; Jackson, D.B.; Zablocki, C.J.

1983-01-01

This document contains complete data from a controlled-source electromagnetic (CSEM) sounding/mapping project at Kilauea volcano, Hawaii. The data were obtained at 46 locations about a fixed-location, horizontal, polygonal loop source in the summit area of the volcano. The data consist of magnetic field amplitudes and phases at excitation frequencies between 0.04 and 8 Hz. The vector components were measured in a cylindrical coordinate system centered on the loop source. 5 references.

50. VIEW LOOKING SOUTHEAST AT A MOTORGENERATOR SET LOCATED UNDER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

50. VIEW LOOKING SOUTHEAST AT A MOTOR-GENERATOR SET LOCATED UNDER CONTROL ROOM. THREE 450 kva., 2500 VOLT, 60 CYCLE MOTOR-GENERATOR UNITS PROVIDED POWER FOR THE RAILROAD SIGNAL SYSTEM. 25 CYCLE POWER WAS PROVIDED TO THE MOTOR (LEFT BACKGROUND). THE MOTOR TURNED THE GENERATOR (CENTER FOREGROUND) WHICH PRODUCED 60 CYCLE POWER TO OPERATE LIGHTS AND SIGNALING DEVICES. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

76 FR 9578 - Clinical Laboratory Improvement Advisory Committee

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Clinical Laboratory Improvement Advisory Committee Correction: This notice was published in the Federal Register on January 31, 2011, Volume 76, Number 20, page 5379. The location of the meeting has changed as follows...

Detail view of the flight deck looking aft. The aft ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of the flight deck looking aft. The aft viewing windows are uncovered in this view and look out towards the payload bay. The overhead viewing windows have exterior covers in place in this view. The aft flight deck contains displays and controls for executing maneuvers for rendezvous, docking, payload deployment and retrieval, payload monitoring and the remote manipulator arm controls. Payload bay doors are also operated from this location. This view was taken in the Orbiter Processing Facility at the Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Airport Remote Tower Sensor Systems

NASA Technical Reports Server (NTRS)

Maluf, David A.; Gawdiak, Yuri; Leidichj, Christopher; Papasin, Richard; Tran, Peter B.; Bass, Kevin

2006-01-01

Networks of video cameras, meteorological sensors, and ancillary electronic equipment are under development in collaboration among NASA Ames Research Center, the Federal Aviation Administration (FAA), and the National Oceanic Atmospheric Administration (NOAA). These networks are to be established at and near airports to provide real-time information on local weather conditions that affect aircraft approaches and landings. The prototype network is an airport-approach-zone camera system (AAZCS), which has been deployed at San Francisco International Airport (SFO) and San Carlos Airport (SQL). The AAZCS includes remotely controlled color video cameras located on top of SFO and SQL air-traffic control towers. The cameras are controlled by the NOAA Center Weather Service Unit located at the Oakland Air Route Traffic Control Center and are accessible via a secure Web site. The AAZCS cameras can be zoomed and can be panned and tilted to cover a field of view 220 wide. The NOAA observer can see the sky condition as it is changing, thereby making possible a real-time evaluation of the conditions along the approach zones of SFO and SQL. The next-generation network, denoted a remote tower sensor system (RTSS), will soon be deployed at the Half Moon Bay Airport and a version of it will eventually be deployed at Los Angeles International Airport. In addition to remote control of video cameras via secure Web links, the RTSS offers realtime weather observations, remote sensing, portability, and a capability for deployment at remote and uninhabited sites. The RTSS can be used at airports that lack control towers, as well as at major airport hubs, to provide synthetic augmentation of vision for both local and remote operations under what would otherwise be conditions of low or even zero visibility.

Earth Observations taken by STS-122 Crewmember

NASA Image and Video Library

2008-02-10

S122-E-007690 (10 Feb. 2008) --- An almost nadir view of the John F. Kennedy Space Center (KSC) was provided by one of STS-122 crewmembers with a digital camera. KSC is the NASA space vehicle launch facility and launch control center (spaceport) on Merritt Island, Brevard County, Florida. The site is near Cape Canaveral, between Miami and Jacksonville. It is 34 miles (55 kilometers) long and around 6 miles (10 kilometers) wide, covering 219 square miles (567 square kilometers). Because much of KSC is a restricted area and only 9 percent of the land is developed, the site also serves as an important wildlife sanctuary; Mosquito Lagoon, Indian River, Merritt Island Wildlife Refuge and Canaveral National Seashore are also features of this area. Pictured just below center is Launch Complex 39, with the roadway leading to the giant Vehicle Assembly Building (VAB), 3 miles (5 kilometers) to the west (above) of the two launch pads. Located 5 miles (8 kilometers) south is the KSC industrial area, where many of the Center's support facilities and the administrative Headquarters Building are located. The Shuttle Landing Facility can be seen northwest of the VAB, in frame center.

The Automation of Nowcast Model Assessment Processes

DTIC Science & Technology

2016-09-01

that will automate real-time WRE-N model simulations, collect and quality control check weather observations for assimilation and verification, and...domains centered near White Sands Missile Range, New Mexico, where the Meteorological Sensor Array (MSA) will be located. The MSA will provide...observations and performing quality -control checks for the pre-forecast data assimilation period. 2. Run the WRE-N model to generate model forecast data

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

In the grasp of the Shuttle's Remote Manipulator System (RMS) robot arm, the U.S. Laboratory, Destiny, is moved from its stowage position in the cargo bay of the Space Shuttle Atlantis. This photograph was taken by astronaut Thomas D. Jones during his Extravehicular Activity (EVA). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter- (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

In the grasp of the Shuttle's Remote Manipulator System (RMS) robot arm, the U.S. Laboratory, Destiny, is moved from its stowage position in the cargo bay of the Space Shuttle Atlantis. This photograph was taken by astronaut Thomas D. Jones during his Extravehicular Activity (EVA). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

With its new U.S. Laboratory, Destiny, contrasted over a blue and white Earth, the International Space Station (ISS) was photographed by one of the STS-98 crew members aboard the Space Shuttle Atlantis following separation of the Shuttle and Station. The Laboratory is shown at the lower right of the Station. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-16

The International Space Station (ISS), with its newly attached U.S. Laboratory, Destiny, was photographed by a crew member aboard the Space Shuttle Orbiter Atlantis during a fly-around inspection after Atlantis separated from the Space Station. The Laboratory is shown in the foreground of this photograph. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-16

With its new U.S. Laboratory, Destiny, contrasted over a blue and white Earth, the International Space Station (ISS) was photographed by one of the STS-98 crew members aboard the Space Shuttle Atlantis following separation of the Shuttle and Station. The Laboratory is shown at the lower right of the Station. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

In the grasp of the Shuttle's Remote Manipulator System (RMS) robot arm, the U.S. Laboratory, Destiny, is moved from its stowage position in the cargo bay of the Space Shuttle Atlantis. This photograph was taken by astronaut Thomas D. Jones during his Extravehicular Activity (EVA). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

In the grasp of the Shuttle's Remote Manipulator System (RMS) robot arm, the U.S. Laboratory, Destiny, is moved from its stowage position in the cargo bay of the Space Shuttle Atlantis. This photograph was taken by astronaut Thomas D. Jones during his Extravehicular Activity (EVA). The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the International Space Station (ISS), where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5- meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter- (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

A robust recognition and accurate locating method for circular coded diagonal target

NASA Astrophysics Data System (ADS)

Bao, Yunna; Shang, Yang; Sun, Xiaoliang; Zhou, Jiexin

2017-10-01

As a category of special control points which can be automatically identified, artificial coded targets have been widely developed in the field of computer vision, photogrammetry, augmented reality, etc. In this paper, a new circular coded target designed by RockeTech technology Corp. Ltd is analyzed and studied, which is called circular coded diagonal target (CCDT). A novel detection and recognition method with good robustness is proposed in the paper, and implemented on Visual Studio. In this algorithm, firstly, the ellipse features of the center circle are used for rough positioning. Then, according to the characteristics of the center diagonal target, a circular frequency filter is designed to choose the correct center circle and eliminates non-target noise. The precise positioning of the coded target is done by the correlation coefficient fitting extreme value method. Finally, the coded target recognition is achieved by decoding the binary sequence in the outer ring of the extracted target. To test the proposed algorithm, this paper has carried out simulation experiments and real experiments. The results show that the CCDT recognition and accurate locating method proposed in this paper can robustly recognize and accurately locate the targets in complex and noisy background.

Joint Optimization of Distribution Network Design and Two-Echelon Inventory Control with Stochastic Demand and CO2 Emission Tax Charges.

PubMed

Li, Shuangyan; Li, Xialian; Zhang, Dezhi; Zhou, Lingyun

2017-01-01

This study develops an optimization model to integrate facility location and inventory control for a three-level distribution network consisting of a supplier, multiple distribution centers (DCs), and multiple retailers. The integrated model addressed in this study simultaneously determines three types of decisions: (1) facility location (optimal number, location, and size of DCs); (2) allocation (assignment of suppliers to located DCs and retailers to located DCs, and corresponding optimal transport mode choices); and (3) inventory control decisions on order quantities, reorder points, and amount of safety stock at each retailer and opened DC. A mixed-integer programming model is presented, which considers the carbon emission taxes, multiple transport modes, stochastic demand, and replenishment lead time. The goal is to minimize the total cost, which covers the fixed costs of logistics facilities, inventory, transportation, and CO2 emission tax charges. The aforementioned optimal model was solved using commercial software LINGO 11. A numerical example is provided to illustrate the applications of the proposed model. The findings show that carbon emission taxes can significantly affect the supply chain structure, inventory level, and carbon emission reduction levels. The delay rate directly affects the replenishment decision of a retailer.

Invasive Cardiologists Are Exposed to Greater Left Sided Cranial Radiation: The BRAIN Study (Brain Radiation Exposure and Attenuation During Invasive Cardiology Procedures).

PubMed

Reeves, Ryan R; Ang, Lawrence; Bahadorani, John; Naghi, Jesse; Dominguez, Arturo; Palakodeti, Vachaspathi; Tsimikas, Sotirios; Patel, Mitul P; Mahmud, Ehtisham

2015-08-17

This study sought to determine radiation exposure across the cranium of cardiologists and the protective ability of a nonlead, XPF (barium sulfate/bismuth oxide) layered cap (BLOXR, Salt Lake City, Utah) during fluoroscopically guided, invasive cardiovascular (CV) procedures. Cranial radiation exposure and potential for protection during contemporary invasive CV procedures is unclear. Invasive cardiologists wore an XPF cap with radiation attenuation ability. Six dosimeters were fixed across the outside and inside of the cap (left, center, and right), and 3 dosimeters were placed outside the catheterization lab to measure ambient exposure. Seven cardiology fellows and 4 attending physicians (38.4 ± 7.2 years of age; all male) performed diagnostic and interventional CV procedures (n = 66.2 ± 27 cases/operator; fluoroscopy time: 14.9 ± 5.0 min). There was significantly greater total radiation exposure at the outside left and outside center (106.1 ± 33.6 mrad and 83.1 ± 18.9 mrad) versus outside right (50.2 ± 16.2 mrad; p < 0.001 for both) locations of the cranium. The XPF cap attenuated radiation exposure (42.3 ± 3.5 mrad, 42.0 ± 3.0 mrad, and 41.8 ± 2.9 mrad at the inside left, inside center, and inside right locations, respectively) to a level slightly higher than that of the ambient control (38.3 ± 1.2 mrad, p = 0.046). After subtracting ambient radiation, exposure at the outside left was 16 times higher than the inside left (p < 0.001) and 4.7 times higher than the outside right (p < 0.001). Exposure at the outside center location was 11 times higher than the inside center (p < 0.001), whereas no difference was observed on the right side. Radiation exposure to invasive cardiologists is significantly higher on the left and center compared with the right side of the cranium. Exposure may be reduced similar to an ambient control level by wearing a nonlead XPF cap. (Brain Radiation Exposure and Attenuation During Invasive Cardiology Procedures [BRAIN]; NCT01910272). Copyright © 2015 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

DENSITY CONTROL IN A REACTOR

DOEpatents

Marshall, J. Jr.

1961-10-24

A reactor is described in which natural-uranium bodies are located in parallel channels which extend through the graphite mass in a regular lattice. The graphite mass has additional channels that are out of the lattice and contain no uranium. These additional channels decrease in number per unit volume of graphite from the center of the reactor to the exterior and have the effect of reducing the density of the graphite more at the center than at the exterior, thereby spreading neutron activity throughout the reactor. (AEC)

Crew Training- STS-11 (RMS)

NASA Image and Video Library

1983-06-14

S83-33925 (14 June 1983) --- Astronaut Ronald E. McNair, one of NASA?s three 41-B mission specialists, participates in a training session in the Shuttle one-g trainer in the Johnson Space Center?s mockup and integrating laboratory. He stands at the aft flight deck, where controls for the remote manipulator system (RMS) arm are located. Dr. McNair and the remainder of the five-man astronaut crew are scheduled to lift into space aboard the Challenger on February 3, 1984.

Peripersonal space as the space of the bodily self.

PubMed

Noel, Jean-Paul; Pfeiffer, Christian; Blanke, Olaf; Serino, Andrea

2015-11-01

Bodily self-consciousness (BSC) refers to experience of one's self as located within an owned body (self-identification) and as occupying a specific location in space (self-location). BSC can be altered through multisensory stimulation, as in the Full Body Illusion (FBI). If participants view a virtual body from a distance being stroked, while receiving synchronous tactile stroking on their physical body, they feel as if the virtual body were their own and they experience, subjectively, to drift toward the virtual body. Here we hypothesized that--while normally the experience of the body in space depends on the integration of multisensory body-related signals within a limited space surrounding the body (i.e. peripersonal space, PPS)--during the FBI the boundaries of PPS would shift toward the virtual body, that is, toward the position of experienced self-location. To test this hypothesis, we used synchronous visuo-tactile stroking to induce the FBI, as contrasted with a control condition of asynchronous stroking. Concurrently, we applied an audio-tactile interaction paradigm to estimate the boundaries of PPS. PPS was measured in front of and behind the participants' body as the distance where tactile information interacted with auditory stimuli looming in space toward the participant's physical body. We found that during synchronous stroking, i.e. when participants experienced the FBI, PPS boundaries extended in the front-space, toward the avatar, and concurrently shrunk in the back-space, as compared to the asynchronous stroking control condition, when FBI was induced. These findings support the view that during the FBI, PPS boundaries translate toward the virtual body, such that the PPS representation shifts from being centered at the location of the physical body to being now centered at the subjectively experienced location of the self. Copyright © 2015 Elsevier B.V. All rights reserved.

Peripersonal Space as the space of the Bodily Self

PubMed Central

Noel, Jean-Paul; Pfeiffer, Christian; Blanke, Olaf; Serino, Andrea

2016-01-01

Bodily self-consciousness (BSC) refers to experience of our self as located within an owned body (self-identification) and as occupying a specific location in space (self-location). BSC can be altered through multisensory stimulation, as in the Full Body Illusion (FBI). If participants view a virtual body from a distance being stroked, while receiving synchronous tactile stroking on their physical body, they feel such as the virtual body were their own and they experience, subjectively, to drift toward the virtual body. Here we hypothesized that - while normally the experience of the body in space depends on the integration of multisensory body-related signals within a limited space surrounding the body (i.e. peripersonal space, PPS) - during the FBI the boundaries of PPS would shift toward the virtual body, that is toward the position of self-location. To test this hypothesis, we used synchronous visuo-tactile stroking to induce the FBI, as contrasted with a control condition of asynchronous stroking. Concurrently, we applied an audio-tactile interaction paradigm to estimate the boundaries of PPS. PPS was measured in front of and behind the participants' body as the distance where tactile information interacted with auditory stimuli looming in space toward the participant's physical body. We found that during synchronous stroking, i.e. when participants experienced the FBI, PPS boundaries extended in the front-space, toward the avatar, and concurrently shrunk in the back-space, as compared to the asynchronous stroking control condition, where no FBI was induced. These findings support the view that during the FBI, PPS boundaries translate toward the virtual body, such that the PPS representation shifts from being centered at the location of the physical body to being now centered at the subjectively experienced location of the self. PMID:26231086

National Center for Nuclear Security - NCNS

ScienceCinema

None

2018-01-16

As the United States embarks on a new era of nuclear arms control, the tools for treaty verification must be accurate and reliable, and must work at stand-off distances. The National Center for Nuclear Security, or NCNS, at the Nevada National Security Site, is poised to become the proving ground for these technologies. The center is a unique test bed for non-proliferation and arms control treaty verification technologies. The NNSS is an ideal location for these kinds of activities because of its multiple environments; its cadre of experienced nuclear personnel, and the artifacts of atmospheric and underground nuclear weapons explosions. The NCNS will provide future treaty negotiators with solid data on verification and inspection regimes and a realistic environment in which future treaty verification specialists can be trained. Work on warhead monitoring at the NCNS will also support future arms reduction treaties.

Reconfiguration control system for an aircraft wing

NASA Technical Reports Server (NTRS)

Wakayama, Sean R. (Inventor)

2008-01-01

Independently deflectable control surfaces are located on the trailing edge of the wing of a blended wing-body aircraft. The reconfiguration control system of the present invention controls the deflection of each control surface to optimize the spanwise lift distribution across the wing for each of several flight conditions, e.g., cruise, pitch maneuver, and high lift at low speed. The control surfaces are deflected and reconfigured to their predetermined optimal positions when the aircraft is in each of the aforementioned flight conditions. With respect to cruise, the reconfiguration control system will maximize the lift to drag ratio and keep the aircraft trimmed at a stable angle of attack. In a pitch maneuver, the control surfaces are deflected to pitch the aircraft and increase lift. Moreover, this increased lift has its spanwise center of pressure shifted inboard relative to its location for cruise. This inboard shifting reduces the increased bending moment about the aircraft's x-axis occasioned by the increased pitch force acting normal to the wing. To optimize high lift at low speed, during take-off and landing for example, the control surfaces are reconfigured to increase the local maximum coefficient of lift at stall-critical spanwise locations while providing pitch trim with control surfaces that are not stall critical.

Telework Centers. An Evaluation of the North American and Japanese Experience. Workscape 21: The Ecology of New Ways of Working.

ERIC Educational Resources Information Center

Becker, Franklin; Rappaport, Andrew J.; Quinn, Kristen L.; Sims, William R.

Telework Centers are work locations used by firms to acommodate staff who live near the telework center location. A study examined the impact of using telework centers on communication, work groups/departments, performance, supervision, travel/environment, and type of work done in various locations. A case study approach was used to investigate 10…

Engineering Technical Support Center Annual Report Fiscal Year 2013; Technical Support and Innovative Research for Contaminated Sites

EPA Science Inventory

This report summarizes a variety of significant projects that the ETSC, located in the Land Remediation and Pollution Control Division (LRPCD), National Risk Management Research Laboratory (NRMRL), has supported throughout fiscal year 2013. Projects have addressed an array of env...

76 FR 18191 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-01

... action would be effective without further notice on May 2, 2011 unless comments are received which result... replace with ``DMDC 10 DoD.'' * * * * * System location: Delete entry and replace with ``Defense Manpower... facilities or using facilities interfacing with Defense Manpower Data Center Physical Access Control Systems...

View of new centrifuge at Flight Acceleration Facility

NASA Technical Reports Server (NTRS)

1966-01-01

View of the new centrifuge at the Manned Spacecraft Center (MSC), located in the Flight Acceleration Facility, bldg 29. The 50-ft. arm can swing the three man gondola to create g-forces astronauts will experience during controlled flight and during reentry. The centrifuge was designed primarily for training Apollo astronauts.

Astronaut Scott Carpenter practices in the ALFA trainer at Langley

NASA Technical Reports Server (NTRS)

1962-01-01

Project Mercury Astronaut M. Scott Carpenter practices in the Air Lubricated Free Attitude (ALFA) trainer located at NASA's Manned Spacecraft Center at Langley AFB, Virginia. This trainer allows the astronaut to see the image of the earth's surface at his feet while manually controlling the spacecraft.

Consolidating NASA's Arc Jets

NASA Technical Reports Server (NTRS)

Balboni, John A.; Gokcen, Tahir; Hui, Frank C. L.; Graube, Peter; Morrissey, Patricia; Lewis, Ronald

2015-01-01

The paper describes the consolidation of NASA's high powered arc-jet testing at a single location. The existing plasma arc-jet wind tunnels located at the Johnson Space Center were relocated to Ames Research Center while maintaining NASA's technical capability to ground-test thermal protection system materials under simulated atmospheric entry convective heating. The testing conditions at JSC were reproduced and successfully demonstrated at ARC through close collaboration between the two centers. New equipment was installed at Ames to provide test gases of pure nitrogen mixed with pure oxygen, and for future nitrogen-carbon dioxide mixtures. A new control system was custom designed, installed and tested. Tests demonstrated the capability of the 10 MW constricted-segmented arc heater at Ames meets the requirements of the major customer, NASA's Orion program. Solutions from an advanced computational fluid dynamics code were used to aid in characterizing the properties of the plasma stream and the surface environment on the calorimeters in the supersonic flow stream produced by the arc heater.

Closeup view of the bottom area of Space Shuttle Main ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close-up view of the bottom area of Space Shuttle Main Engine (SSME) 2052 engine assembly mounted in a SSME Engine Handler in the Horizontal Processing area of the SSME Processing Facility at Kennedy Space Center. The most prominent features in this view are the Low-Pressure Oxidizer Discharge Duct toward the bottom of the assembly, the SSME Engine Controller and the Main Fuel Valve Hydraulic Actuator are in the approximate center of the assembly in this view, the Low-Pressure Fuel Turbopump (LPFTP), the LPFTP Discharge Duct are to the left on the assembly in this view and the High-Pressure Fuel Turbopump is located toward the top of the engine assembly in this view. The ring of tabs in the right side of the image, at the approximate location of the Nozzle and the Coolant Outlet Manifold interface is the Heat Shield Support Ring. - Space Transportation System, Space Shuttle Main Engine, Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Airspace Analysis for Phase II of the Regional Airport Plan Update Program.

DTIC Science & Technology

1979-03-01

Base; and Hamilton, Sonoma County , and Napa County Airports) is comparable in terms of airspace capacity. Note that if the aircraft redistributed to the...Oakland ARTCC (Oakland Center) Napa County Airport Sonoma County Airport (at Santa Rosa) Stockton Approach Control Livermore Municipal Airport... Sonoma County Airport The ATC Tower located at these airports exercises control of aircraft within the Airport Traffic Areas. Rules of aircraft

Exploratory wind tunnel investigation of the stability and control characteristics of a three-surface, forward-swept wing advanced turboprop model

NASA Technical Reports Server (NTRS)

Coe, Paul L., Jr.; Perkins, John N.; Owens, D. Bruce

1990-01-01

The purpose of the present investigation was to parametrically study the stability and control characteristics of a forward-swept wing three-surface turboprop model through an extended angle of attack range, including the deep-stall region. As part of a joint research program between North Carolina State University and NASA Langley Research Center, a low-speed wind tunnel investigation was conducted with a three-surface, forward-swept wing, aft-mounted, twin-pusher propeller, model, representative of an advanced turboprop configuration. The tests were conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. The model parameters varied in the test were horizontal tail location, canard size, sweep and location, and wing position. The model was equipped with air turbines, housed within the nacelles and driven by compressed air, to model turboprop power effects. A three-surface, forward-swept wing configuration that provided satisfactory static longitudinal and lateral/directional stability was identified. The three-surface configuration was found to have greater longitudinal control and increased center of gravity range relative to a conventional (two-surface) design. The test showed that power had a large favorable effect on stability and control about all three axis in the post-stall regime.

ED08-0109-08

NASA Image and Video Library

2008-05-01

Ikhana fiber optic wing shape sensor team: clockwise from left, Anthony "Nino" Piazza, Allen Parker, William Ko and Lance Richards. The sensors, located along a fiber the thickness of a human hair, aren't visible in the center of the Ikhana aircraft's left wing. NASA Dryden Flight Research Center is evaluating an advanced fiber optic-based sensing technology installed on the wings of NASA's Ikhana aircraft. The fiber optic system measures and displays the shape of the aircraft's wings in flight. There are other potential safety applications for the technology, such as vehicle structural health monitoring. If an aircraft structure can be monitored with sensors and a computer can manipulate flight control surfaces to compensate for stresses on the wings, structural control can be established to prevent situations that might otherwise result in a loss of control.

10. Interior view of control room in Components Test Laboratory ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Interior view of control room in Components Test Laboratory (T-27), looking east. The control room is located in the center of the building and abuts the Test Cell 8, 9, and 10 and equipment room wings. Photograph shows upgraded instrumentation, piping, and technological modifications installed in 1997-99 to accommodate component testing requirements for the Atlas V missile. - Air Force Plant PJKS, Systems Integration Laboratory, Components Test Laboratory, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

KSC-02pd1418

NASA Image and Video Library

2002-10-01

KENNEDY SPACE CENTER, FLA. - STS-112 Pilot Pamela Ann Melroy (left) conducts a last-minute inspection of some cables inside Space Shuttle Atlantis at Launch Pad 39B prior to the launch of her mission. The STS-112 crew also includes Commander Jeffrey S. Ashby and Mission Specialists David A. Wolf, Sandra H. Magnus, Piers J. Sellers, and Fyodor N. Yurchikhin of the Russian Space Agency. Launch of the mission was postponed today to no earlier than Thursday, Oct. 3, while weather forecasters and the mission management team assess the possible effect Hurricane Lili may have on the Mission Control Center located at the Lyndon B. Johnson Space Center in Houston, Texas.

Design of a wheeled articulating land rover

NASA Technical Reports Server (NTRS)

Stauffer, Larry; Dilorenzo, Mathew; Yandle, Barbara

1994-01-01

The WALRUS is a wheeled articulating land rover that will provide Ames Research Center with a reliable, autonomous vehicle for demonstrating and evaluating advanced technologies. The vehicle is one component of the Ames Research Center's on-going Human Exploration Demonstration Project. Ames Research Center requested a system capable of traversing a broad spectrum of surface types and obstacles. In addition, this vehicle must have an autonomous navigation and control system on board and its own source of power. The resulting design is a rover that articulates in two planes of motion to allow for increased mobility and stability. The rover is driven by six conical shaped aluminum wheels, each with an independent, internally coupled motor. Mounted on the rover are two housings and a removable remote control system. In the housings, the motor controller board, tilt sensor, navigation circuitry, and QED board are mounted. Finally, the rover's motors and electronics are powered by thirty C-cell rechargeable batteries, which are located in the rover wheels and recharged by a specially designed battery charger.

The Tripartite Seminars at the Russian Methodological and Training Center: An Overview of Progress in Nuclear Materials Control and Accounting in the Russian Federation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pshakin, Gennady; Dickman, Deborah A.; Ryazanov, Boris

2003-09-16

The development of the Russian Methodological and Training Center (RMTC) has been an important element of collaboration between the Russian Federation (RF), the European Union and the US. The RMTC, located at the Institute of Physics and Power Engineering (IPPE) in Obninsk, Russia has been designated by the Russian Ministry of Atomic Energy (Minatom) to provide nuclear materials protection, control and Accounting training to Minatom and the Federal Nuclear and Radiation Safety Authority (Gosatomnadzor) personnel. In addition, the RMTC was chartered with the responsibility of providing a venue for exchange of experiences and information between Russian and international specialists.

US Search and Rescue Mission Control Center functions

NASA Technical Reports Server (NTRS)

1977-01-01

A satellite aided Search and Rescue (SAR) Mission concept consisting of a local coverage bent pipe system, and a global coverage system is described. The SAR instrument is to consist of a Canadian repeater and a French processor for which Canada and France, respectively are to evaluate health and trends. Performance evaluations of each system were provided. The United States and Canada will each have a Search and Rescue Mission Control Center (MCC) and their functions were also examined. A summary of the interface requirements necessary to perform each function was included as well as the information requirements between the USMCC and each of its interfaces. Physical requirements such as location, manning etc. of the USMCC were discussed.

ATS-1/ATS-3 dual satellite navigation study

NASA Technical Reports Server (NTRS)

Hoover, W. M.

1971-01-01

A study which illustrated the feasibility of implementing an on-board aircraft navigation system based on using the ATS-1 and ATS-3 satellites, the modified Omega Position Location Equipment (OPLE) Control Center, and a suitable aircraft terminal was conducted. The report provides: (1) a consideration of the problems of satellite navigation and an objective definition of the optimum system under the constraints of its specified components, (2) a description of the necessary modifications to the OPLE Control Center, the design of an aircraft terminal, and the design of ground reference terminals, and (3) an outline of an experiment plan and an estimate of the cost to be expected in conducting the program.

An aerodynamic assessment of various supersonic fighter airplanes based on Soviet design concepts

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1983-01-01

The aerodynamic, stability, and control characteristics of several supersonic fighter airplane concepts were assessed. The configurations include fixed-wing airplanes having delta wings, swept wings, and trapezoidal wings, and variable wing-sweep airplanes. Each concept employs aft tail controls. The concepts vary from lightweight, single engine, air superiority, point interceptor, or ground attack types to larger twin-engine interceptor and reconnaissance designs. Results indicate that careful application of the transonic or supersonic area rule can provide nearly optimum shaping for minimum drag for a specified Mach number requirement. Through the proper location of components and the exploitation of interference flow fields, the concepts provide linear pitching moment characteristics, high control effectiveness, and reasonably small variations in aerodynamic center location with a resulting high potential for maneuvering capability. By careful attention to component shaping and location and through the exploitation of local flow fields, favorable roll-to-yaw ratios may result and a high degree of directional stability can be achieved.

General view of a Space Shuttle Main Engine (SSME) mounted ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of a Space Shuttle Main Engine (SSME) mounted on an SSME engine handler, taken in the SSME Processing Facility at Kennedy Space Center. The most prominent features of the engine assembly in this view are the Low-Pressure Oxidizer Turbopump Discharge Duct looping around the right side of the engine assembly then turning in and connecting to the High-Pressure Oxidizer Turbopump. The sphere in the approximate center of the assembly is the POGO System Accumulator, the Engine Controller is located on the bottom and slightly left of the center of the Engine Assembly in this view. - Space Transportation System, Space Shuttle Main Engine, Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

DCDM1: Lessons Learned from the World's Most Energy Efficient Data Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sickinger, David E; Van Geet, Otto D; Carter, Thomas

This presentation discusses the holistic approach to design the world's most energy-efficient data center, which is located at the U.S. Department of Energy National Renewable Energy Laboratory (NREL). This high-performance computing (HPC) data center has achieved a trailing twelve-month average power usage effectiveness (PUE) of 1.04 and features a chiller-less design, component-level warm-water liquid cooling, and waste heat capture and reuse. We provide details of the demonstrated PUE and energy reuse effectiveness (ERE) and lessons learned during four years of production operation. Recent efforts to dramatically reduce the water footprint will also be discussed. Johnson Controls partnered with NREL andmore » Sandia National Laboratories to deploy a thermosyphon cooler (TSC) as a test bed at NREL's HPC data center that resulted in a 50% reduction in water usage during the first year of operation. The Thermosyphon Cooler Hybrid System (TCHS) integrates the control of a dry heat rejection device with an open cooling tower.« less

Stimulated emission depletion microscopy resolves individual nitrogen vacancy centers in diamond nanocrystals.

PubMed

Arroyo-Camejo, Silvia; Adam, Marie-Pierre; Besbes, Mondher; Hugonin, Jean-Paul; Jacques, Vincent; Greffet, Jean-Jacques; Roch, Jean-François; Hell, Stefan W; Treussart, François

2013-12-23

Nitrogen-vacancy (NV) color centers in nanodiamonds are highly promising for bioimaging and sensing. However, resolving individual NV centers within nanodiamond particles and the controlled addressing and readout of their spin state has remained a major challenge. Spatially stochastic super-resolution techniques cannot provide this capability in principle, whereas coordinate-controlled super-resolution imaging methods, like stimulated emission depletion (STED) microscopy, have been predicted to fail in nanodiamonds. Here we show that, contrary to these predictions, STED can resolve single NV centers in 40-250 nm sized nanodiamonds with a resolution of ≈10 nm. Even multiple adjacent NVs located in single nanodiamonds can be imaged individually down to relative distances of ≈15 nm. Far-field optical super-resolution of NVs inside nanodiamonds is highly relevant for bioimaging applications of these fluorescent nanolabels. The targeted addressing and readout of individual NV(-) spins inside nanodiamonds by STED should also be of high significance for quantum sensing and information applications.

Launch vehicle flight control augmentation using smart materials and advanced composites (CDDF Project 93-05)

NASA Technical Reports Server (NTRS)

Barret, C.

1995-01-01

The Marshall Space Flight Center has a rich heritage of launch vehicles that have used aerodynamic surfaces for flight stability such as the Saturn vehicles and flight control such as on the Redstone. Recently, due to aft center-of-gravity locations on launch vehicles currently being studied, the need has arisen for the vehicle control augmentation that is provided by these flight controls. Aerodynamic flight control can also reduce engine gimbaling requirements, provide actuator failure protection, enhance crew safety, and increase vehicle reliability, and payload capability. In the Saturn era, NASA went to the Moon with 300 sq ft of aerodynamic surfaces on the Saturn V. Since those days, the wealth of smart materials and advanced composites that have been developed allow for the design of very lightweight, strong, and innovative launch vehicle flight control surfaces. This paper presents an overview of the advanced composites and smart materials that are directly applicable to launch vehicle control surfaces.

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Testbed Manager Louis MacDowell (right) explains to Center Director Jim Kennedy about the test blocks being used to test a newly developed coating to protect steel inside concrete. Between MacDowell and Kennedy are Dr. Paul Hintze and Lead Scientist Dr. Luz Marina Calle. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Testbed Manager Louis MacDowell (right) explains to Center Director Jim Kennedy about the test blocks being used to test a newly developed coating to protect steel inside concrete. Between MacDowell and Kennedy are Dr. Paul Hintze and Lead Scientist Dr. Luz Marina Calle. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

Declining functional connectivity and changing hub locations in Alzheimer's disease: an EEG study.

PubMed

Engels, Marjolein M A; Stam, Cornelis J; van der Flier, Wiesje M; Scheltens, Philip; de Waal, Hanneke; van Straaten, Elisabeth C W

2015-08-20

EEG studies have shown that patients with Alzheimer's disease (AD) have weaker functional connectivity than controls, especially in higher frequency bands. Furthermore, active regions seem more prone to AD pathology. How functional connectivity is affected in AD subgroups of disease severity and how network hubs (highly connected brain areas) change is not known. We compared AD patients with different disease severity and controls in terms of functional connections, hub strength and hub location. We studied routine 21-channel resting-state electroencephalography (EEG) of 318 AD patients (divided into tertiles based on disease severity: mild, moderate and severe AD) and 133 age-matched controls. Functional connectivity between EEG channels was estimated with the Phase Lag Index (PLI). From the PLI-based connectivity matrix, the minimum spanning tree (MST) was derived. For each node (EEG channel) in the MST, the betweenness centrality (BC) was computed, a measure to quantify the relative importance of a node within the network. Then we derived color-coded head plots based on BC values and calculated the center of mass (the exact middle had x and y values of 0). A shifting of the hub locations was defined as a shift of the center of mass on the y-axis across groups. Multivariate general linear models with PLI or BC values as dependent variables and the groups as continuous variables were used in the five conventional frequency bands. We found that functional connectivity decreases with increasing disease severity in the alpha band. All, except for posterior, regions showed increasing BC values with increasing disease severity. The center of mass shifted from posterior to more anterior regions with increasing disease severity in the higher frequency bands, indicating a loss of relative functional importance of the posterior brain regions. In conclusion, we observed decreasing functional connectivity in the posterior regions, together with a shifted hub location from posterior to central regions with increasing AD severity. Relative hub strength decreases in posterior regions while other regions show a relative rise with increasing AD severity, which is in accordance with the activity-dependent degeneration theory. Our results indicate that hubs are disproportionally affected in AD.

Reliable and Affordable Control Systems Active Combustor Pattern Factor Control

NASA Technical Reports Server (NTRS)

McCarty, Bob; Tomondi, Chris; McGinley, Ray

2004-01-01

Active, closed-loop control of combustor pattern factor is a cooperative effort between Honeywell (formerly AlliedSignal) Engines and Systems and the NASA Glenn Research Center to reduce emissions and turbine-stator vane temperature variations, thereby enhancing engine performance and life, and reducing direct operating costs. Total fuel flow supplied to the engine is established by the speed/power control, but the distribution to individual atomizers will be controlled by the Active Combustor Pattern Factor Control (ACPFC). This system consist of three major components: multiple, thin-film sensors located on the turbine-stator vanes; fuel-flow modulators for individual atomizers; and control logic and algorithms within the electronic control.

Implementing health management information systems: measuring success in Korea's health centers.

PubMed

Chae, Y M; Kim, S I; Lee, B H; Choi, S H; Kim, I S

1994-01-01

This article analyses the effects that the introduction and adoption of a health management information system (HMIS) can have on both the productivity of health center staff as well as on user-satisfaction. The focus is upon the service provided by the Kwonsun Health Center located in Suwon City, Korea. Two surveys were conducted to measure the changes in productivity and adoption (knowledge, persuasion, decision, implementation and confirmation) of health center staff over time. In addition, a third survey was conducted to measure the effects of HMIS on the level of satisfaction perceived by the visitors, by comparing the satisfaction level between the study health center and a similar health center identified as a control. The results suggest that HMIS increased the productivity and satisfaction of the staff but did not increase their persuasion and decision levels; and, that is also succeeded in increasing the levels of visitors' satisfaction with the services provided.

KSC-05pd2569

NASA Image and Video Library

2005-12-06

KENNEDY SPACE CENTER, FLA. -- Inside NASA Kennedy Space Center’s Orbiter Processing Facility Bay 1, workers get ready to lift the sling placed round the forward reaction control system that will be installed on Atlantis. The forward reaction control system is located in the forward fuselage nose area. During ascent of the space shuttle, it provides the thrust for attitude (rotational) maneuvers (pitch, yaw and roll) and for small velocity changes along the orbiter axis (translation maneuvers).

Colloquia | Cancer Prevention Fellowship Program

Cancer.gov

The Cancer Prevention and Control Colloquia Series features current research findings from guest researchers from a variety of research disciplines. Topics cover current challenges and methods used by investigators to address gaps, advance the field of cancer prevention and control, and promote the application of successful strategies. When Usually twice a month on Tuesday from 11:00 am - noon between September and June. Where NCI's Shady Grove Campus, 9609 Medical Center Drive, Rockville, MD (conference room locations vary).

iss01e5107

NASA Image and Video Library

2000-12-01

ISS01-E-5107 (December 2000) --- This nadir view of a Chilean glaciated area was provided by one of the early December digital still camera images down linked from the International Space Station (ISS) to ground controllers in Houston. The remote headwaters of the Rio de la Colonia are located on the eastern flank of the Cerro Pared Norte, a high, coastal range of the Andes in southern Chile. This is but a portion of a larger glaciated region of the Chilean coast located at only 47 degrees south latitude. The river actually begins its flow just off the top of this scene at the foot of the two large, converging, valley glaciers near the center. Some of the numerous lakes visible are tinted by the fine glacial sediments suspended in their waters. Note the shards of ice that have calved from the glaciers into the lakes on the left. Also note the shadows of the crest of the over 14,000-foot mountains (lower center). The remote headwaters of the Rio de la Colonia are located on the eastern flank of the Cerro Pared Norte, a high, coastal range of the Andes in southern Chile. This is a but a portion of a larger glaciated region of the Chilean coast located at only 47 degrees south latitude. The river actually begins its flow just off the top of this scene at the foot of the two large, converging, valley glaciers near the center. Some of the numerous lakes visible are tinted by the fine glacial sediments suspended in their waters. Note the shards of ice that have calved from the glaciers into the lakes on the left. Also note the shadows of the crest of the over 14,000-foot mountains (lower center).

A PDP-15 to industrial-14 interface at the Lewis Research Center's cyclotron

NASA Technical Reports Server (NTRS)

Kebberly, F. R.; Leonard, R. F.

1977-01-01

An interface (hardware and software) was built which permits the loading, monitoring, and control of a digital equipment industrial-14/30 programmable controller by a PDP-15 computer. The interface utilizes the serial mode for data transfer to and from the controller, so that the required hardware is essentially that of a teletype unit except for the speed of transmission. Software described here permits the user to load binary paper tape, read or load individual controller memory locations, and if desired turn controller outputs on and off directly from the computer.

Analysis of logistic distribution performance of good supply from PT. Mentari Trans Nusantara distribution center to branches using Smart PLS 3.0

NASA Astrophysics Data System (ADS)

Endrawati, Titin; Siregar, M. Tirtana

2018-03-01

PT Mentari Trans Nusantara is a company engaged in the distribution of goods from the manufacture of the product to the distributor branch of the customer so that the product distribution must be controlled directly from the PT Mentari Trans Nusantara Center for faster delivery process. Problems often occur on the expedition company which in charge in sending the goods although it has quite extensive networking. The company is less control over logistics management. Meanwhile, logistics distribution management control policy will affect the company's performance in distributing products to customer distributor branches and managing product inventory in distribution center. PT Mentari Trans Nusantara is an expedition company which engaged in good delivery, including in Jakarta. Logistics management performance is very important due to its related to the supply of goods from the central activities to the branches based oncustomer demand. Supply chain management performance is obviously depends on the location of both the distribution center and branches, the smoothness of transportation in the distribution and the availability of the product in the distribution center to meet the demand in order to avoid losing sales. This study concluded that the company could be more efficient and effective in minimizing the risks of loses by improve its logistic management.

A comparative analysis of resistance testing methods in Aedes albopictus (Diptera: Culicidae) from St. Johns County, Florida

USDA-ARS?s Scientific Manuscript database

Aedes albopictus Skuse (Diptera: Culicidae) was tested for resistance to permethrin, bifenthrin, and malathion using Centers for Disease Control and Prevention (CDC) bottle bioassays and topical toxicology assays on adults and larval bioassays. Eggs were collected from 3 locations across St. Johns C...

Identification and location of catenary insulator in complex background based on machine vision

NASA Astrophysics Data System (ADS)

Yao, Xiaotong; Pan, Yingli; Liu, Li; Cheng, Xiao

2018-04-01

It is an important premise to locate insulator precisely for fault detection. Current location algorithms for insulator under catenary checking images are not accurate, a target recognition and localization method based on binocular vision combined with SURF features is proposed. First of all, because of the location of the insulator in complex environment, using SURF features to achieve the coarse positioning of target recognition; then Using binocular vision principle to calculate the 3D coordinates of the object which has been coarsely located, realization of target object recognition and fine location; Finally, Finally, the key is to preserve the 3D coordinate of the object's center of mass, transfer to the inspection robot to control the detection position of the robot. Experimental results demonstrate that the proposed method has better recognition efficiency and accuracy, can successfully identify the target and has a define application value.

STS-98 Onboard Photograph-U.S. Laboratory, Destiny

NASA Technical Reports Server (NTRS)

2001-01-01

The International Space Station (ISS), with the newly installed U.S. Laboratory, Destiny, is backdropped over clouds, water and land in South America. South Central Chile shows up at the bottom of the photograph. Just below the Destiny, the Chacao Charnel separates the large island of Chile from the mainland and connects the Gulf of Coronado on the Pacific side with the Gulf of Ancud, southwest of the city of Puerto Montt. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

International Space Station (ISS)

NASA Image and Video Library

2001-02-16

The International Space Station (ISS), with the newly installed U.S. Laboratory, Destiny, is backdropped over clouds, water and land in South America. South Central Chile shows up at the bottom of the photograph. Just below the Destiny, the Chacao Charnel separates the large island of Chile from the mainland and connects the Gulf of Coronado on the Pacific side with the Gulf of Ancud, southwest of the city of Puerto Montt. The American-made Destiny module is the cornerstone for space-based research aboard the orbiting platform and the centerpiece of the ISS, where unprecedented science experiments will be performed in the near-zero gravity of space. Destiny will also serve as the command and control center for the ISS. The aluminum module is 8.5-meters (28-feet) long and 4.3-meters (14-feet) in diameter. The laboratory consists of three cylindrical sections and two endcones with hatches that will be mated to other station components. A 50.9-centimeter (20-inch-) diameter window is located on one side of the center module segment. This pressurized module is designed to accommodate pressurized payloads. It has a capacity of 24 rack locations. Payload racks will occupy 15 locations especially designed to support experiments. The Destiny module was built by the Boeing Company under the direction of the Marshall Space Flight Center.

Cancellation control law for lateral-directional dynamics of a supermaneuverable aircraft

NASA Technical Reports Server (NTRS)

Snell, Antony

1993-01-01

Cancellation control laws are designed which reduce the high levels of lateral acceleration encountered during aggressive rolling maneuvers executed at high angle of attack. Two independent problem are examined. One is to reduce lateral acceleration at the mass center, while the other focuses on lateral acceleration at the pilot's station, located 7.0 m forward of the mass center. Both of these problems are challenging and somewhat different in their limitations. In each case the design is based on a linearization of the lateral-directional dynamics about a high angle of attack condition. The controllers incorporate dynamic inversion inner loops to provide control of stability-axis roll- and yaw-rates and then employ cancellation filters in both feed-forward and feed-back signal paths. The relative simplicity of the control laws should allow nonlinear generalizations to be devised. Although it is shown that lateral acceleration can be reduced substantially by such control laws, this is at the cost of slowed roll response, poor dutch-roll damping or a combination of the two.

Trim drag reduction concepts for horizontal takeoff single-stage-to-Orbit vehicles

NASA Technical Reports Server (NTRS)

Shaughnessy, John D.; Gregory, Irene M.

1991-01-01

The results of a study to investigate concepts for minimizing trim drag of horizontal takeoff single-stage-to-orbit (SSTO) vehicles are presented. A generic hypersonic airbreathing conical configuration was used as the subject aircraft. The investigation indicates that extreme forward migration of the aerodynamic center as the vehicle accelerates to orbital velocities causes severe aerodynamic instability and trim moments that must be counteracted. Adequate stability can be provided by active control of elevons and rudder, but use of elevons to produce trim moments results in excessive trim drag and fuel consumption. To alleviate this problem, two solution concepts are examined. Active control of the center of gravity (COG) location to track the aerodynamic center decreases trim moment requirements, reduces elevon deflections, and leads to significant fuel savings. Active control of the direction of the thrust vector produces required trim moments, reduces elevon deflections, and also results in significant fuel savings. It is concluded that the combination of active flight control to provide stabilization, (COG) position control to minimize trim moment requirements, and thrust vectoring to generate required trim moments has the potential to significantly reduce fuel consumption during ascent to orbit of horizontal takeoff SSTO vehicles.

Optical Sensor/Actuator Locations for Active Structural Acoustic Control

NASA Technical Reports Server (NTRS)

Padula, Sharon L.; Palumbo, Daniel L.; Kincaid, Rex K.

1998-01-01

Researchers at NASA Langley Research Center have extensive experience using active structural acoustic control (ASAC) for aircraft interior noise reduction. One aspect of ASAC involves the selection of optimum locations for microphone sensors and force actuators. This paper explains the importance of sensor/actuator selection, reviews optimization techniques, and summarizes experimental and numerical results. Three combinatorial optimization problems are described. Two involve the determination of the number and position of piezoelectric actuators, and the other involves the determination of the number and location of the sensors. For each case, a solution method is suggested, and typical results are examined. The first case, a simplified problem with simulated data, is used to illustrate the method. The second and third cases are more representative of the potential of the method and use measured data. The three case studies and laboratory test results establish the usefulness of the numerical methods.

Joint Optimization of Distribution Network Design and Two-Echelon Inventory Control with Stochastic Demand and CO2 Emission Tax Charges

PubMed Central

Li, Shuangyan; Li, Xialian; Zhang, Dezhi; Zhou, Lingyun

2017-01-01

This study develops an optimization model to integrate facility location and inventory control for a three-level distribution network consisting of a supplier, multiple distribution centers (DCs), and multiple retailers. The integrated model addressed in this study simultaneously determines three types of decisions: (1) facility location (optimal number, location, and size of DCs); (2) allocation (assignment of suppliers to located DCs and retailers to located DCs, and corresponding optimal transport mode choices); and (3) inventory control decisions on order quantities, reorder points, and amount of safety stock at each retailer and opened DC. A mixed-integer programming model is presented, which considers the carbon emission taxes, multiple transport modes, stochastic demand, and replenishment lead time. The goal is to minimize the total cost, which covers the fixed costs of logistics facilities, inventory, transportation, and CO2 emission tax charges. The aforementioned optimal model was solved using commercial software LINGO 11. A numerical example is provided to illustrate the applications of the proposed model. The findings show that carbon emission taxes can significantly affect the supply chain structure, inventory level, and carbon emission reduction levels. The delay rate directly affects the replenishment decision of a retailer. PMID:28103246

12. GENERAL VIEW TO THE WEST FROM NEAR BUILDING NO. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. GENERAL VIEW TO THE WEST FROM NEAR BUILDING NO. 14 (CONTROL HOUSE FOR DRY DOCK), NOW LOCATED AT THE EAST END OF THE PROJECT AREA. IN THE LEFT FAR DISTANCE ARE TWO WATER TOWERS OF THE FORMER ALAMEDA NAVAL AIR STATION. DIRECTLY BENEATH THEM IS THE FRAME OF BUILDING NO. 6. BUILDING NO. 1 IS IN THE CENTER DISTANCE, MOSTLY OBSCURED BY A MODERN METAL BUILDING. BUILDING NO. 18 AND THE WET BASIN ARE AT RIGHT CENTER, IN DISTANCE. - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

Linear magnetic bearings

NASA Technical Reports Server (NTRS)

Goldowskiy, M. P.

1984-01-01

A self regulating, nonfrictional, active magnetic bearing is disclosed which has an elongated cylindrical housing for containing a shaft type armature with quadrature positioned shaft position sensors and equidistantly positioned electromagnets located at one end of the housing. Each set of sensors is responsive to orthogonal displacement of the armature and is used to generate control signals to energize the electromagnets to center the armature. A bumper magnet assembly is located at one end of the housing for dampening any undesired axial movement of the armature or to axially move the armature either continuously or fixedly.

Associations of Distance to Trauma Care, Community Income, and Neighborhood Median Age With Rates of Injury Mortality.

PubMed

Jarman, Molly P; Curriero, Frank C; Haut, Elliott R; Pollack Porter, Keshia; Castillo, Renan C

2018-02-07

Rural, low-income, and historically underrepresented minority communities face substantial barriers to trauma care and experience high injury incidence and mortality rates. Characteristics of injury incident locations may contribute to poor injury outcomes. To examine the association of injury scene characteristics with injury mortality. In this cross-sectional study, data from trauma center and emergency medical services provided by emergency medical services companies and designated trauma centers in the state of Maryland from January 1, 2015, to December 31, 2015, were geocoded by injury incident locations and linked with injury scene characteristics. Participants included adults who experienced traumatic injury in Maryland and were transported to a designated trauma center or died while in emergency medical services care at the incident scene or in transit. The primary exposures of interest were geographic characteristics of injury incident locations, including distance to the nearest trauma center, designation level and ownership status of the nearest trauma center, and land use, as well as community-level characteristics such as median age and per capita income. Odds of death were estimated with multilevel logistic regression, controlling for individual demographic measures and measures of injury and health. Of the 16 082 patients included in this study, 8716 (52.4%) were white, and 5838 (36.3%) were African American. Most patients were male (10 582; 65.8%) and younger than 65 years (12 383; 77.0%). Odds of death increased by 8.0% for every 5-mile increase in distance to the nearest trauma center (OR, 1.08; 95% CI, 1.01-1.15; P = .03). Compared with privately owned level 1 or 2 centers, odds of death increased by 49.9% when the nearest trauma center was level 3 (OR, 1.50; 95% CI, 1.06-2.11; P = .02), and by 80.7% when the nearest trauma center was publicly owned (OR, 1.81; 95% CI, 1.39-2.34; P < .001). At the zip code tabulation area level, odds of death increased by 16.0% for every 5-year increase in median age (OR, 1.16; 95% CI, 1.03-1.30; P = .02), and decreased by 26.6% when the per capita income was greater than $25 000 (OR, 0.73; 95% CI, 0.54-0.99; P = .05). Injury scene characteristics are associated with injury mortality. Odds of death are highest for patients injured in communities with higher median age or lower per capita income and at locations farthest from level 1 or 2 trauma centers.

[Effect of school-based peer leader centered smoking prevention program].

PubMed

Shin, Sung Rae; Oh, Pok Ja; Youn, Hye Kyung; Shin, Sun Hwa

2014-12-01

The purpose of this study was to develop and evaluate a school-based peer leader centered smoking prevention program. Non-equivalent control group with a pre/post-test design was used. Students (n=174) in two boys' junior high schools located in D city, Korea participated with 85 being selected for the experimental group and 89 for the control group. Five sessions were given to the experimental group and a 50 minute lecture to the control group. Knowledge, attitude, non-smoking intention, and non-smoking efficacy were measured for the both experimental and control group at two weeks before the program and one month after the program was completed. Data were analyzed using χ²-test, Fisher's exact test, independent t-test and paired t-test with the SPSS 21.0 program. The experimental group showed higher overall knowledge, negative attitude toward smoking, and higher non-smoking intention and efficacy. After receiving the school based peer leader centered smoking prevention program scores for attitude toward smoking and non-smoking efficacy increased in the experimental group were higher than in the control group. The school-based peer leader centered smoking prevention program needs longitudinal evaluation, but from this study, there is an indication that this program can be used with junior high school students and effectively change students' attitude toward smoking and promote non-smoking efficacy.

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

The Payload Operations Center (POC) is the science command post for the International Space Station (ISS). Located at NASA's Marshall Space Flight Center in Huntsville, Alabama, it is the focal point for American and international science activities aboard the ISS. The POC's unique capabilities allow science experts and researchers around the world to perform cutting-edge science in the unique microgravity environment of space. The POC is staffed around the clock by shifts of payload flight controllers. At any given time, 8 to 10 flight controllers are on consoles operating, plarning for, and controlling various systems and payloads. This photograph shows a Payload Rack Officer (PRO) at a work station. The PRO is linked by a computer to all payload racks aboard the ISS. The PRO monitors and configures the resources and environment for science experiments including EXPRESS Racks, multiple-payload racks designed for commercial payloads.

Balance training and center-of-pressure location in participants with chronic ankle instability.

PubMed

Mettler, Abby; Chinn, Lisa; Saliba, Susan A; McKeon, Patrick O; Hertel, Jay

2015-04-01

Chronic ankle instability (CAI) occurs in some people after a lateral ankle sprain and often results in residual feelings of instability and episodes of the ankle's giving way. Compared with healthy people, patients with CAI demonstrated poor postural control and used a more anteriorly and laterally positioned center of pressure (COP) during a single-limb static-balance task on a force plate. Balance training is an effective means of altering traditional COP measures; however, whether the overall location of the COP distribution under the foot also changes is unknown. To determine if the spatial locations of COP data points in participants with CAI change after a 4-week balance-training program. Randomized controlled trial. Laboratory. Thirty-one persons with self-reported CAI. Participants were randomly assigned to a 4-week balance-training program or no balance training. We collected a total of 500 COP data points while participants balanced using a single limb on a force plate during a 10-second trial. The location of each COP data point relative to the geometric center of the foot was determined, and the frequency count in 4 sections (anteromedial, anterolateral, posteromedial, posterolateral) was analyzed for differences between groups. Overall, COP position in the balance-training group shifted from being more anterior to less anterior in both eyes-open trials (before trial = 319.1 ± 165.4, after trial = 160.5 ± 149.5; P = .006) and eyes-closed trials (before trial = 387.9 ± 123.8, after trial = 189.4 ± 102.9; P < .001). The COP for the group that did not perform balance training remained the same in the eyes-open trials (before trial = 214.1 ± 193.3, after trial = 230.0 ± 176.3; P = .54) and eyes-closed trials (before trial = 326.9 ± 134.3, after trial = 338.2 ± 126.1; P = .69). In participants with CAI, the balance-training program shifted the COP location from anterolateral to posterolateral. The program may have repaired some of the damaged sensorimotor system pathways, resulting in a more optimally functioning and less constrained system.

Center of mass detection via an active pixel sensor

NASA Technical Reports Server (NTRS)

Yadid-Pecht, Orly (Inventor); Minch, Brad (Inventor); Pain, Bedabrata (Inventor); Fossum, Eric (Inventor)

2005-01-01

An imaging system for identifying the location of the center of mass (COM) in an image. In one aspect, an imaging system includes a plurality of photosensitive elements arranged in a matrix. A center of mass circuit coupled to the photosensitive elements includes a resistive network and a normalization circuit including at least one bipolar transistor. The center of mass circuit identifies a center of mass location in the matrix and includes: a row circuit, where the row circuit identifies a center of mass row value in each row of the matrix and identifies a row intensity for each row; a horizontal circuit, where the horizontal circuit identifies a center of mass horizontal value; and a vertical circuit, where the vertical circuit identifies a center of mass vertical value. The horizontal and vertical center of mass values indicate the coordinates of the center of mass location for the image.

Center of mass detection via an active pixel sensor

NASA Technical Reports Server (NTRS)

Yadid-Pecht, Orly (Inventor); Minch, Brad (Inventor); Pain, Bedabrara (Inventor); Fossum, Eric (Inventor)

2006-01-01

An imaging system for identifying the location of the center of mass (COM) in an image. In one aspect, an imaging system includes a plurality of photosensitive elements arranged in a matrix. A center of mass circuit coupled to the photosensitive elements includes a resistive network and a normalization circuit including at least one bipolar transistor. The center of mass circuit identifies a center of mass location in the matrix and includes: a row circuit, where the row circuit identifies a center of mass row value in each row of the matrix and identifies a row intensity for each row; a horizontal circuit, where the horizontal circuit identifies a center of mass horizontal value; and a vertical circuit, where the vertical circuit identifies a center of mass vertical value. The horizontal and vertical center of mass values indicate the coordinates of the center of mass location for the image.

Center of mass detection via an active pixel sensor

NASA Technical Reports Server (NTRS)

Yadid-Pecht, Orly (Inventor); Minch, Brad (Inventor); Pain, Bedabrata (Inventor); Fossum, Eric (Inventor)

2002-01-01

An imaging system for identifying the location of the center of mass (COM) in an image. In one aspect, an imaging system includes a plurality of photosensitive elements arranged in a matrix. A center of mass circuit coupled to the photosensitive elements includes a resistive network and a normalization circuit including at least one bipolar transistor. The center of mass circuit identifies a center of mass location in the matrix and includes: a row circuit, where the row circuit identifies a center of mass row value in each row of the matrix and identifies a row intensity for each row; a horizontal circuit, where the horizontal circuit identifies a center of mass horizontal value; and a vertical circuit, where the vertical circuit identifies a center of mass vertical value. The horizontal and vertical center of mass values indicate the coordinates of the center of mass location for the image.

Mass center estimation of a drag-free satellite

NASA Technical Reports Server (NTRS)

Sanz Fernandez De Cordova, S.; Debra, D. B.

1975-01-01

The mass center location of a spinning drag-free satellite can be estimated because there is control required to accelerate the mass center along the axis of spin as long as there is some nutation in the spinning motion. Linear and nonlinear models are compared and observability discussed. Online estimation fails when nutation is damped so an offline mechanization is proposed. A new sensor has been designed to permit greater relative motion than was possible on the drag-free satellite flown in 1972 (JH-1). Experimental laboratory results using a spinning vehicle with the new sensor mounted 30 cm from a spherical air bearing support are presented which confirm earlier simulation results.

STS-112 Pilot Melroy inspects cables prior to launch

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. - STS-112 Pilot Pamela Ann Melroy (left) conducts a last-minute inspection of some cables inside Space Shuttle Atlantis at Launch Pad 39B prior to the launch of her mission. The STS-112 crew also includes Commander Jeffrey S. Ashby and Mission Specialists David A. Wolf, Sandra H. Magnus, Piers J. Sellers, and Fyodor N. Yurchikhin of the Russian Space Agency. Launch of the mission was postponed today to no earlier than Thursday, Oct. 3, while weather forecasters and the mission management team assess the possible effect Hurricane Lili may have on the Mission Control Center located at the Lyndon B. Johnson Space Center in Houston, Texas.

STS-112 crew with President of Ajara in Georgia (Russia)

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- In the Operations and Checkout Building, Aslan Abashidze (left), President of the Autonomous Republic of Ajara in Georgia (Russia), STS-112 Mission Specialist Fyodor N. Yurchikhin, Ph.D., a cosmonaut with the Russian Space Agency; and Georgi Abashidze, Mayor of Batumi (Yurchikhin's hometown), pose for a portrait. Yurchikhin and the other members of the STS-112 crew are awaiting launch to the International Space Station aboard Space Shuttle Atlantis. The launch has been postponed to no earlier than Monday, Oct. 7, so that the Mission Control Center, located at the Lyndon B. Johnson Space Center in Houston, Texas, can be secured and protected from potential storm impacts from Hurricane Lili.

Environmental Control and Life Support Systems Test Facility at MSFC

NASA Technical Reports Server (NTRS)

2001-01-01

The Marshall Space Flight Center (MSFC) is responsible for designing and building the life support systems that will provide the crew of the International Space Station (ISS) a comfortable environment in which to live and work. Scientists and engineers at the MSFC are working together to provide the ISS with systems that are safe, efficient, and cost-effective. These compact and powerful systems are collectively called the Environmental Control and Life Support Systems, or simply, ECLSS. This photograph shows the development Water Processor located in two racks in the ECLSS test area at the Marshall Space Flight Center. Actual waste water, simulating Space Station waste, is generated and processed through the hardware to evaluate the performance of technologies in the flight Water Processor design.

Design of automatic leveling and centering system of theodolite

NASA Astrophysics Data System (ADS)

Liu, Chun-tong; He, Zhen-Xin; Huang, Xian-xiang; Zhan, Ying

2012-09-01

To realize the theodolite automation and improve the azimuth Angle measurement instrument, the theodolite automatic leveling and centering system with the function of leveling error compensation is designed, which includes the system solution, key components selection, the mechanical structure of leveling and centering, and system software solution. The redesigned leveling feet are driven by the DC servo motor; and the electronic control center device is installed. Using high precision of tilt sensors as horizontal skew detection sensors ensures the effectiveness of the leveling error compensation. Aiming round mark center is located using digital image processing through surface array CCD; and leveling measurement precision can reach the pixel level, which makes the theodolite accurate centering possible. Finally, experiments are conducted using the automatic leveling and centering system of the theodolite. The results show the leveling and centering system can realize automatic operation with high centering accuracy of 0.04mm.The measurement precision of the orientation angle after leveling error compensation is improved, compared with that of in the traditional method. Automatic leveling and centering system of theodolite can satisfy the requirements of the measuring precision and its automation.

The influence of vehicle aerodynamic and control response characteristics on driver-vehicle performance

NASA Technical Reports Server (NTRS)

Alexandridis, A. A.; Repa, B. S.; Wierwille, W. W.

1978-01-01

The effects of changes in understeer, control sensitivity, and location of the lateral aerodynamic center of pressure (c.p.) of a typical passenger car on the driver's opinion and on the performance of the driver-vehicle system were studied in a moving-base driving simulator. Twelve subjects with no prior experience on the simulator and no special driving skills performed regulation tasks in the presence of both random and step wind gusts.

War on Drugs: Reauthorization of the Office of National Drug Control Policy

DTIC Science & Technology

2005-06-01

Authorization of the Office of National Drug Control Policy (ONDCP) expired on September 30, 2003. Located in the Executive Office of the President...Counter-Drug Technology Assessment Center. The office was created in 1988 and reauthorized twice since then. A bill has been introduced in the House (H.R...Congress as it prepares to consider reauthorization of the office of the drug czar. This report will be updated as legislative activity occurs.

Development Activities Locator and Assessment Method (DALAM)

DTIC Science & Technology

2013-11-01

click tab for “leading health indicators.” - Center for Disease Control : o http://www.cdc.gov and choose from “health and safety topics” on the home...to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE...losers” if the project is executed? Who are they? Why? Can they be co-opted or compensated ? - Does the project compensate beneficiaries for an

Automatic image acquisition processor and method

DOEpatents

Stone, William J.

1986-01-01

A computerized method and point location system apparatus is disclosed for ascertaining the center of a primitive or fundamental object whose shape and approximate location are known. The technique involves obtaining an image of the object, selecting a trial center, and generating a locus of points having a predetermined relationship with the center. Such a locus of points could include a circle. The number of points overlying the object in each quadrant is obtained and the counts of these points per quadrant are compared. From this comparison, error signals are provided to adjust the relative location of the trial center. This is repeated until the trial center overlies the geometric center within the predefined accuracy limits.

Automatic image acquisition processor and method

DOEpatents

Stone, W.J.

1984-01-16

A computerized method and point location system apparatus is disclosed for ascertaining the center of a primitive or fundamental object whose shape and approximate location are known. The technique involves obtaining an image of the object, selecting a trial center, and generating a locus of points having a predetermined relationship with the center. Such a locus of points could include a circle. The number of points overlying the object in each quadrant is obtained and the counts of these points per quadrant are compared. From this comparison, error signals are provided to adjust the relative location of the trial center. This is repeated until the trial center overlies the geometric center within the predefined accuracy limits.

Design of a robotic vehicle with self-contained intelligent wheels

NASA Astrophysics Data System (ADS)

Poulson, Eric A.; Jacob, John S.; Gunderson, Robert W.; Abbott, Ben A.

1998-08-01

The Center for Intelligent Systems has developed a small robotic vehicle named the Advanced Rover Chassis 3 (ARC 3) with six identical intelligent wheel units attached to a payload via a passive linkage suspension system. All wheels are steerable, so the ARC 3 can move in any direction while rotating at any rate allowed by the terrain and motors. Each intelligent wheel unit contains a drive motor, steering motor, batteries, and computer. All wheel units are identical, so manufacturing, programing, and spare replacement are greatly simplified. The intelligent wheel concept would allow the number and placement of wheels on the vehicle to be changed with no changes to the control system, except to list the position of all the wheels relative to the vehicle center. The task of controlling the ARC 3 is distributed between one master computer and the wheel computers. Tasks such as controlling the steering motors and calculating the speed of each wheel relative to the vehicle speed in a corner are dependent on the location of a wheel relative to the vehicle center and ar processed by the wheel computers. Conflicts between the wheels are eliminated by computing the vehicle velocity control in the master computer. Various approaches to this distributed control problem, and various low level control methods, have been explored.

Barriers and facilitators to senior centers participating in translational research.

PubMed

Felix, Holly C; Adams, Becky; Cornell, Carol E; Fausett, Jennifer K; Krukowski, Rebecca A; Love, ShaRhonda J; Prewitt, T Elaine; West, Delia Smith

2014-01-01

Senior centers are ideal locations to deliver evidence-based health promotion programs to the rapidly growing population of older Americans to help them remain healthy and independent in the community. However, little reported research is conducted in partnership with senior centers; thus, not much is known about barriers and facilitators for senior centers serving as research sites. To fill this gap and potentially accelerate research within senior centers to enhance translation of evidence-based interventions into practice, the present study examined barriers and facilitators of senior centers invited to participate in a cluster-randomized controlled trial. Primary barriers to participation related to staffing and perceived inability to recruit older adult participants meeting research criteria. The primary facilitator was a desire to offer programs that were of interest and beneficial to seniors. Senior centers are interested in participating in research that provides benefit to older adults but may need assistance from researchers to overcome participation barriers. © The Author(s) 2012.

Suppression of flutter

NASA Technical Reports Server (NTRS)

Nissim, E. (Inventor)

1973-01-01

An active aerodynamic control system to control flutter over a large range of oscillatory frequencies is described. The system is not affected by mass, stiffness, elastic axis, or center of gravity location of the system, mode of vibration, or Mach number. The system consists of one or more pairs of leading edge and trailing edge hinged or deformable control surfaces, each pair operated in concert by a stability augmentation system. Torsion and bending motions are sensed and converted by the stability augmentation system into leading and trailing edge control surface deflections which produce lift forces and pitching moments to suppress flutter.

Direct Observation of Pore Formation and Bubble Mobility during Controlled Melting and Resolidification in Microgravity

NASA Technical Reports Server (NTRS)

Grugel, Richard N.; Anilkumar, A. V.; Lee, C. P.

2004-01-01

Detailed studies on the controlled melting and subsequent re-solidification of succinonitrile were conducted in the microgravity environment aboard the International Space Station (ISS) using the PFMI apparatus (Pore Formation and Mobility Investigation) located in the ISS glovebox facility (GBX). Samples were initially prepared on ground by filling glass tubes, 1 cm ID and approximately 30 cm in length, with pure succinonitrile (SCN) under 450 millibar of nitrogen. During Space processing, experimental parameters like temperature gradient and translation speed, for melting and solidification, were remotely monitored and controlled from the ground Telescience Center (TSC) at the Marshall Space Flight Center. Real time visualization during controlled melting revealed bubbles of different sizes initiating at the solid/liquid interface, and traveling up the temperature gradient ahead of them. Subsequent controlled re-solidification of the SCN revealed the details of porosity formation and evolution. A preliminary analysis of the melt back and re- solidification and its implications to future microgravity materials processing is presented and discussed.

Continuous on-line steam quality monitoring system of the Bacman Geothermal Production Field, Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solis, R.P.; Chavez, F.C.; Garcia, S.E.

1997-12-31

In any operating geothermal power plant, steam quality is one of the most important parameters being monitored. In the Bacon-Manito Geothermal Production Field (BGPF), an online steam quality monitoring system have been installed in two operating power plants which provides an accurate, efficient and continuous real-time data which is more responsive to the various requirements of the field operation. The system utilizes sodium as an indicator of steam purity. Sodium concentration is read by the flame photometer located at the interface after aspirating a sample of the condensed steam through a continuous condensate sampler. The condensate has been degassed throughmore » a condensate-NCG separator. The flame photometer analog signal is then converted by a voltage-to-current converter/transmitter and relayed to the processor which is located at the control center through electrical cable to give a digital sodium concentration read-out at the control panel. The system features a high and high-high sodium level alarm, a continuous strip-chart recorder and a central computer for data capture, retrieval, and processing for further interpretation. Safety devices, such as the flame-off indicator at the control center and the automatic fuel cut-off device along the fuel line, are incorporated in the system.« less

Robust Eye Center Localization through Face Alignment and Invariant Isocentric Patterns

PubMed Central

Teng, Dongdong; Chen, Dihu; Tan, Hongzhou

2015-01-01

The localization of eye centers is a very useful cue for numerous applications like face recognition, facial expression recognition, and the early screening of neurological pathologies. Several methods relying on available light for accurate eye-center localization have been exploited. However, despite the considerable improvements that eye-center localization systems have undergone in recent years, only few of these developments deal with the challenges posed by the profile (non-frontal face). In this paper, we first use the explicit shape regression method to obtain the rough location of the eye centers. Because this method extracts global information from the human face, it is robust against any changes in the eye region. We exploit this robustness and utilize it as a constraint. To locate the eye centers accurately, we employ isophote curvature features, the accuracy of which has been demonstrated in a previous study. By applying these features, we obtain a series of eye-center locations which are candidates for the actual position of the eye-center. Among these locations, the estimated locations which minimize the reconstruction error between the two methods mentioned above are taken as the closest approximation for the eye centers locations. Therefore, we combine explicit shape regression and isophote curvature feature analysis to achieve robustness and accuracy, respectively. In practical experiments, we use BioID and FERET datasets to test our approach to obtaining an accurate eye-center location while retaining robustness against changes in scale and pose. In addition, we apply our method to non-frontal faces to test its robustness and accuracy, which are essential in gaze estimation but have seldom been mentioned in previous works. Through extensive experimentation, we show that the proposed method can achieve a significant improvement in accuracy and robustness over state-of-the-art techniques, with our method ranking second in terms of accuracy. According to our implementation on a PC with a Xeon 2.5Ghz CPU, the frame rate of the eye tracking process can achieve 38 Hz. PMID:26426929

Championing School-Located Influenza Immunization: The School Nurse's Role

ERIC Educational Resources Information Center

Li, Christina; Freedman, Marian; Boyer-Chu, Lynda

2009-01-01

According to the 2008 recommendations of the Advisory Committee on Immunization Practices of the Centers for Disease Control and Prevention, influenza vaccine should be administered on an annual basis to all children aged 6 months through 18 years. School-age children are more likely than any other age group to be infected with influenza, and…

The Deployment of a Commercial RGA to the International Space Station

NASA Technical Reports Server (NTRS)

Kowitt, Matt; Hawk, Doug; Rossetti, Dino; Woronowicz, Michael

2015-01-01

The International Space Station (ISS) uses ammonia as a medium for heat transport in its Active Thermal Control System. Over time, there have been intermittent component failures and leaks in the ammonia cooling loop. One specific challenge in dealing with an ammonia leak on the exterior of the ISS is determining the exact location from which ammonia is escaping before addressing the problem. Together, researchers and engineers from Stanford Research Systems (SRS) and NASA's Johnson Space Center and Goddard Space Flight Center have adapted a commercial off-the-shelf (COTS) residual gas analyzer (RGA) for repackaging and operation outside the ISS as a core component in the ISS Robotic External Leak Locator, a technology demonstration payload currently scheduled for launch during 2015. The packaging and adaptation of the COTS RGA to the Leak Locator will be discussed. The collaborative process of adapting a commercial instrument for spaceflight will also be reviewed, including the build-­-up of the flight units. Measurements from a full-­-scale thermal vacuum test will also be presented demonstrating the absolute and directional sensitivity of the RGA.

Interaction between gaze and visual and proprioceptive position judgements.

PubMed

Fiehler, Katja; Rösler, Frank; Henriques, Denise Y P

2010-06-01

There is considerable evidence that targets for action are represented in a dynamic gaze-centered frame of reference, such that each gaze shift requires an internal updating of the target. Here, we investigated the effect of eye movements on the spatial representation of targets used for position judgements. Participants had their hand passively placed to a location, and then judged whether this location was left or right of a remembered visual or remembered proprioceptive target, while gaze direction was varied. Estimates of position of the remembered targets relative to the unseen position of the hand were assessed with an adaptive psychophysical procedure. These positional judgements significantly varied relative to gaze for both remembered visual and remembered proprioceptive targets. Our results suggest that relative target positions may also be represented in eye-centered coordinates. This implies similar spatial reference frames for action control and space perception when positions are coded relative to the hand.

Hypergol Systems: Design, Buildup, and Operation

NASA Technical Reports Server (NTRS)

Baker, David; Rathgeber, Kurt

2006-01-01

This course was developed by personnel at the NASA JSC White Sands Test Facility in conjunction with the NASA Safety Training Center (NSTC). The NSTC was established in May 1991 by the NASA Headquarters Safety Directorate to provide up-to-date, high-quality, NASA specific safety training on location at NASA centers, or simultaneously to multiple centers over the Video Teleconferencing System (ViTS). Our desire is to establish and maintain a strong, long-lasting relationship with all NASA centers in order to fulfill your safety training needs on a cost-effective basis. Our ultimate goal is to provide a positive contribution to safe operations at NASA. NSTC Course 055 is a 2-day course discussing the safe usage of hypergols (hydrazine fuels and nitrogen tetroxide). During the course we will identify the hazards associated with hypergols including toxicity, reactivity, fire, and explosion. Management of risk is discussed in terms of the primary engineering controls design, buildup, and operation; and secondary controls personal protective equipment and detectors/monitors. The emphasis is on the design and buildup of compatible systems and the safe operation of these systems by technicians and engineers.

Site Rehabilitation Completion Report with No Further Action Proposal for the Northeast Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, Joe; Tabor, Charles; Survochak, Scott

2013-05-01

The purpose of this Site Rehabilitation Completion Report is to present the post-active-remediation monitoring results for the Northeast Site and to propose No Further Action with Controls. This document includes information required by Chapter 62-780.750(4)(d), 62-780.750(6), and 62-780.600(8)(a)27 Florida Administrative Code (F.A.C.). The Closure Monitoring Plan for the Northeast Site and 4.5 Acre Site (DOE 2009a) describes the approach for post-active-remediation monitoring. The Young - Rainey Science, Technology, and Research Center (STAR Center) is a former U.S. Department of Energy (DOE) facility constructed in the mid-1950s. The 99-acre STAR Center is located in Largo, Florida. The Northeast Site is locatedmore » in the northeast corner of the STAR Center. The Northeast Site meets all the requirements for an RMO II closure—No Further Action with Controls. DOE is nearing completion of a restrictive covenant for the Northeast Site. DOE has completed post-active-remediation monitoring at the Northeast Site as of September 2012. No additional monitoring will be conducted.« less

Results from Testing Crew-Controlled Surface Telerobotics on the International Space Station

NASA Technical Reports Server (NTRS)

Bualat, Maria; Schreckenghost, Debra; Pacis, Estrellina; Fong, Terrence; Kalar, Donald; Beutter, Brent

2014-01-01

During Summer 2013, the Intelligent Robotics Group at NASA Ames Research Center conducted a series of tests to examine how astronauts in the International Space Station (ISS) can remotely operate a planetary rover. The tests simulated portions of a proposed lunar mission, in which an astronaut in lunar orbit would remotely operate a planetary rover to deploy a radio telescope on the lunar far side. Over the course of Expedition 36, three ISS astronauts remotely operated the NASA "K10" planetary rover in an analogue lunar terrain located at the NASA Ames Research Center in California. The astronauts used a "Space Station Computer" (crew laptop), a combination of supervisory control (command sequencing) and manual control (discrete commanding), and Ku-band data communications to command and monitor K10 for 11 hours. In this paper, we present and analyze test results, summarize user feedback, and describe directions for future research.

JPL's Real-Time Weather Processor project (RWP) metrics and observations at system completion

NASA Technical Reports Server (NTRS)

Loesh, Robert E.; Conover, Robert A.; Malhotra, Shan

1990-01-01

As an integral part of the overall upgraded National Airspace System (NAS), the objective of the Real-Time Weather Processor (RWP) project is to improve the quality of weather information and the timeliness of its dissemination to system users. To accomplish this, an RWP will be installed in each of the Center Weather Service Units (CWSUs), located in 21 of the 23 Air Route Traffic Control Centers (ARTCCs). The RWP System is a prototype system. It is planned that the software will be GFE and that production hardware will be acquired via industry competitive procurement. The ARTCC is a facility established to provide air traffic control service to aircraft operating on Instrument Flight Rules (IFR) flight plans within controlled airspace, principally during the en route phase of the flight. Covered here are requirement metrics, Software Problem Failure Reports (SPFRs), and Ada portability metrics and observations.

Thermal transistor utilizing gas-liquid transition.

PubMed

Komatsu, Teruhisa S; Ito, Nobuyasu

2011-01-01

We propose a simple thermal transistor, a device to control heat current. In order to effectively change the current, we utilize the gas-liquid transition of the heat-conducting medium (fluid) because the gas region can act as a good thermal insulator. The three terminals of the transistor are located at both ends and the center of the system, and are put into contact with distinct heat baths. The key idea is a special arrangement of the three terminals. The temperature at one end (the gate temperature) is used as an input signal to control the heat current between the center (source, hot) and another end (drain, cold). Simulating the nanoscale systems of this transistor, control of heat current is demonstrated. The heat current is effectively cut off when the gate temperature is cold and it flows normally when it is hot. By using an extended version of this transistor, we also simulate a primitive application for an inverter.

KSC-05pd2567

NASA Image and Video Library

2005-12-06

KENNEDY SPACE CENTER, FLA. -- Inside NASA Kennedy Space Center’s Orbiter Processing Facility Bay 1, workers make adjustments to the sling being placed round the forward reaction control system that will be installed on Atlantis. When ready, the shuttle equipment will be lifted for installation. The forward reaction control system is located in the forward fuselage nose area. During ascent of the space shuttle, it provides the thrust for attitude (rotational) maneuvers (pitch, yaw and roll) and for small velocity changes along the orbiter axis (translation maneuvers).

KSC-05pd2566

NASA Image and Video Library

2005-12-06

KENNEDY SPACE CENTER, FLA. -- Inside NASA Kennedy Space Center’s Orbiter Processing Facility Bay 1, workers move the sling into place around the forward reaction control system that will be installed on Atlantis. When ready, the shuttle equipment will be lifted for installation. The forward reaction control system is located in the forward fuselage nose area. During ascent of the space shuttle, it provides the thrust for attitude (rotational) maneuvers (pitch, yaw and roll) and for small velocity changes along the orbiter axis (translation maneuvers).

KSC-05pd2568

NASA Image and Video Library

2005-12-06

KENNEDY SPACE CENTER, FLA. -- Inside NASA Kennedy Space Center’s Orbiter Processing Facility Bay 1, workers secure the overhead crane to the sling placed round the forward reaction control system that will be installed on Atlantis. When ready, the shuttle equipment will be lifted for installation. The forward reaction control system is located in the forward fuselage nose area. During ascent of the space shuttle, it provides the thrust for attitude (rotational) maneuvers (pitch, yaw and roll) and for small velocity changes along the orbiter axis (translation maneuvers).

STS payloads mission control study continuation phase A-1. Volume 2-B: Task 2. Evaluation and refinement of implementation guidelines for the selected STS payload operator concept

NASA Technical Reports Server (NTRS)

1976-01-01

The functions of Payload Operations Control Centers (POCC) at JSC, GSFC, JPL, and non-NASA locations are analyzed to establish guidelines for standardization, and facilitate the development of a fully integrated NASA-wide system of ground facilities for all classes of payloads. Operational interfaces between the space transportation system operator and the payload operator elements are defined. The advantages and disadvantages of standardization are discussed.

Morphing wing structure with controllable twist based on adaptive bending-twist coupling

NASA Astrophysics Data System (ADS)

Raither, Wolfram; Heymanns, Matthias; Bergamini, Andrea; Ermanni, Paolo

2013-06-01

A novel semi-passive morphing airfoil concept based on variable bending-twist coupling induced by adaptive shear center location and torsional stiffness is presented. Numerical parametric studies and upscaling show that the concept relying on smart materials permits effective twist control while offering the potential of being lightweight and energy efficient. By means of an experimental characterization of an adaptive beam and a scaled adaptive wing structure, effectiveness and producibility of the structural concept are demonstrated.

Corrosion detector apparatus for universal assessment of pollution in data centers

DOEpatents

Hamann, Hendrik F.; Klein, Levente I.

2015-08-18

A compact corrosion measurement apparatus and system includes an air fan, a corrosion sensor, a temperature sensor, a humidity sensor, a heater element, and an air flow sensor all under control to monitor and maintain constant air parameters in an environment and minimize environmental fluctuations around the corrosion sensor to overcome the variation commonly encountered in corrosion rate measurement. The corrosion measurement apparatus includes a structure providing an enclosure within which are located the sensors. Constant air flow and temperature is maintained within the enclosure where the corrosion sensor is located by integrating a variable speed air fan and a heater with the corresponding feedback loop control. Temperature and air flow control loops ensure that corrosivity is measured under similar conditions in different facilities offering a general reference point that allow a one to one comparison between facilities with similar or different pollution levels.

High-voltage R-F feedthrough bushing

DOEpatents

Grotz, G.F.

1982-09-03

Described is a multi-element, high voltage radio frequency bushing for transmitting rf energy to an antenna located in a vacuum container. The bushing includes a center conductor of complex geometrical shape, an outer coaxial shield conductor, and a thin-walled hollow truncated cone insulator disposed between central and outer conductors. The shape of the center conductor, which includes a reverse curvature portion formed of a radially inwardly directed shoulder and a convex portion, controls the uniformity of the axial surface gradient on the insulator cone. The outer shield has a first substantially cylindrical portion and a second radially inwardly extending truncated cone portion.

High voltage RF feedthrough bushing

DOEpatents

Grotz, Glenn F.

1984-01-01

Described is a multi-element, high voltage radio frequency bushing for trmitting RF energy to an antenna located in a vacuum container. The bushing includes a center conductor of complex geometrical shape, an outer coaxial shield conductor, and a thin-walled hollow truncated cone insulator disposed between central and outer conductors. The shape of the center conductor, which includes a reverse curvature portion formed of a radially inwardly directed shoulder and a convex portion, controls the uniformity of the axial surface gradient on the insulator cone. The outer shield has a first substantially cylindrical portion and a second radially inwardly extending truncated cone portion.

Effect of Changing the Center of Gravity on Human Performance in Simulated Lunar Gravity

NASA Technical Reports Server (NTRS)

Chappell, Steven P.; Norcross, Jason R.; Gernhardt, Michael L.

2010-01-01

The presentation slides include: Moving Past Apollo, Testing in Analog Environments, NEEMO/NBL CG (center of gravity) Studies, Center of Gravity Test Design and Methods, CG Suited Locations and Results, CG Individual Considerations, CG Shirt-Sleeve Locations and Results.

Logistics Distribution Center Location Evaluation Based on Genetic Algorithm and Fuzzy Neural Network

NASA Astrophysics Data System (ADS)

Shao, Yuxiang; Chen, Qing; Wei, Zhenhua

Logistics distribution center location evaluation is a dynamic, fuzzy, open and complicated nonlinear system, which makes it difficult to evaluate the distribution center location by the traditional analysis method. The paper proposes a distribution center location evaluation system which uses the fuzzy neural network combined with the genetic algorithm. In this model, the neural network is adopted to construct the fuzzy system. By using the genetic algorithm, the parameters of the neural network are optimized and trained so as to improve the fuzzy system’s abilities of self-study and self-adaptation. At last, the sampled data are trained and tested by Matlab software. The simulation results indicate that the proposed identification model has very small errors.

Conflict and disfluency as aversive signals: context-specific processing adjustments are modulated by affective location associations.

PubMed

Dreisbach, Gesine; Reindl, Anna-Lena; Fischer, Rico

2018-03-01

Context-specific processing adjustments are one signature feature of flexible human action control. However, up to now the precise mechanisms underlying these adjustments are not fully understood. Here it is argued that aversive signals produced by conflict- or disfluency-experience originally motivate such context-specific processing adjustments. We tested whether the efficiency of the aversive conflict signal for control adaptation depends on the affective nature of the context it is presented in. In two experiments, high vs. low proportions of aversive signals (Experiment 1: conflict trials; Experiment 2: disfluent trials) were presented either above or below the screen center. This location manipulation was motivated by existing evidence that verticality is generally associated with affective valence with up being positive and down being negative. From there it was hypothesized that the aversive signals would lose their trigger function for processing adjustments when presented at the lower (i.e., more negative) location. This should then result in a reduced context-specific proportion effect when the high proportion of aversive signals was presented at the lower location. Results fully confirmed the predictions. In both experiments, the location-specific proportion effects were only present when the high proportion of aversive signals occurred at the more positive location above but were reduced (Experiment 1) or even eliminated (Experiment 2) when the high proportion occurred at the more negative location below. This interaction of processing adjustments with affective background contexts can thus be taken as further hint for an affective origin of control adaptations.

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Louis MacDowell (right), Testbed manager, explains to Center Director Jim Kennedy a project being undertaken for the U.S. Navy. At left are nonchrome primers for aircraft being studied. Behind Kennedy is Lead Scientist Dr. Luz Marina Calle. Behind MacDowell is Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Louis MacDowell (right), Testbed manager, explains to Center Director Jim Kennedy a project being undertaken for the U.S. Navy. At left are nonchrome primers for aircraft being studied. Behind Kennedy is Lead Scientist Dr. Luz Marina Calle. Behind MacDowell is Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Center Director Jim Kennedy (second from right) learns from Testbed Manager Louis MacDowell (right) about a project being undertaken for the U.S. Navy. Being studied are nonchrome primers for aircraft. At left are Lead Scientist Dr. Luz Marina Calle and Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Center Director Jim Kennedy (second from right) learns from Testbed Manager Louis MacDowell (right) about a project being undertaken for the U.S. Navy. Being studied are nonchrome primers for aircraft. At left are Lead Scientist Dr. Luz Marina Calle and Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Testbed Manager Louis MacDowell (foreground) explains to Center Director Jim Kennedy (third from right) about a study being undertaken for the U.S. Navy: nonchrome primers for aircraft. At left is Lead Scientist Dr. Luz Marina Calle and behind MacDowell is Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

NASA Image and Video Library

2003-08-21

KENNEDY SPACE CENTER, FLA. - On a tour of the KSC Beach Corrosion Test Site, Testbed Manager Louis MacDowell (foreground) explains to Center Director Jim Kennedy (third from right) about a study being undertaken for the U.S. Navy: nonchrome primers for aircraft. At left is Lead Scientist Dr. Luz Marina Calle and behind MacDowell is Dr. Paul Hintze, who is working on a graduate project for the National Research Council. The KSC Beach Corrosion Test Site was established in the 1960s and has provided more than 30 years of historical information on the long-term performance of many materials in use at KSC and other locations around the world. Located 100 feet from the Atlantic Ocean approximately 1 mile south of the Space Shuttle launch sites, the test facility includes an atmospheric exposure site, a flowing seawater exposure site, and an on-site electrochemistry laboratory and monitoring station. The beach laboratory is used to conduct real-time corrosion experiments and provides for the remote monitoring of surrounding weather conditions. The newly added flowing seawater immersion facility provides for the immersion testing of materials and devices under controlled conditions.

Efficient management of cardiovascular risk screening programs

NASA Technical Reports Server (NTRS)

Roth, Carol

1993-01-01

The Environmental Health Unit, located on-site at the the Goddard Space Flight Center (GSFC), is responsible for the implementation of the Center's Employee Environmental and Occupational Health Program. The Health Unit, Health Physics (HP), and Industrial Hygiene (IH) staffs collaborate to provide quality service to the employees at GSFC. The Health Unit staff identifies, evaluates, and ensures the control of occupational hazards on the Center. In the past, components of the Industrial Hygiene Program have included the Industrial Hygiene Health Hazard Identification Program (IHHIP), the Hearing Conservation Program (HCP), the Hazard Communication Program, and the bi-annual fume hood survey. More recently, the Environmental Health Unit has expanded its services by adding the Ergonomics Program. Various aspects of the Ergonomics Program are discussed.

Entry Vehicle Control System Design for the Mars Smart Lander

NASA Technical Reports Server (NTRS)

Calhoun, Philip C.; Queen, Eric M.

2002-01-01

The NASA Langley Research Center, in cooperation with the Jet Propulsion Laboratory, participated in a preliminary design study of the Entry, Descent and Landing phase for the Mars Smart Lander Project. This concept utilizes advances in Guidance, Navigation and Control technology to significantly reduce uncertainty in the vehicle landed location on the Mars surface. A candidate entry vehicle controller based on the Reaction Control System controller for the Apollo Lunar Excursion Module digital autopilot is proposed for use in the entry vehicle attitude control. A slight modification to the phase plane controller is used to reduce jet-firing chattering while maintaining good control response for the Martian entry probe application. The controller performance is demonstrated in a six-degree-of-freedom simulation with representative aerodynamics.

Intelligent Software for System Design and Documentation

NASA Technical Reports Server (NTRS)

2002-01-01

In an effort to develop a real-time, on-line database system that tracks documentation changes in NASA's propulsion test facilities, engineers at Stennis Space Center teamed with ECT International of Brookfield, WI, through the NASA Dual-Use Development Program to create the External Data Program and Hyperlink Add-on Modules for the promis*e software. Promis*e is ECT's top-of-the-line intelligent software for control system design and documentation. With promis*e the user can make use of the automated design process to quickly generate control system schematics, panel layouts, bills of material, wire lists, terminal plans and more. NASA and its testing contractors currently use promis*e to create the drawings and schematics at the E2 Cell 2 test stand located at Stennis Space Center.

The Role of the George Kuzmycz Training Center in Improving the Nuclear Material Management Culture in Ukraine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavrylyuk, V. I.; Scherbachenko, A. M.; Bazavov, D. A.

2001-01-01

The George Kuzmycz Training Center for Physical Protection, Control and Accounting (GKTC) was established in 1998 in a collaborative endeavor of the State Nuclear Regulatory Administration of Ukraine, the Ukrainian Academy of Sciences, and the U.S. Department of Energy. Located at the Institute for Nuclear Research in Kyiv, the GKTC provides theoretical and practical training in physical protection, control, and accounting techniques and systems that are employed to reduce the risk of unauthorized use, theft, or diversion of weapons-usable nuclear material. Participants in GKTC workshops and courses include nuclear facility specialists as well as officials of the State's regulatory authorities.more » Recently, the training scope has been broadened to include students from other nations in the region.« less

Space Station Environmental Control and Life Support System Test Facility at Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Springer, Darlene

1989-01-01

Different aspects of Space Station Environmental Control and Life Support System (ECLSS) testing are currently taking place at Marshall Space Flight Center (MSFC). Unique to this testing is the variety of test areas and the fact that all are located in one building. The north high bay of building 4755, the Core Module Integration Facility (CMIF), contains the following test areas: the Subsystem Test Area, the Comparative Test Area, the Process Material Management System (PMMS), the Core Module Simulator (CMS), the End-use Equipment Facility (EEF), and the Pre-development Operational System Test (POST) Area. This paper addresses the facility that supports these test areas and briefly describes the testing in each area. Future plans for the building and Space Station module configurations will also be discussed.

KSC-04PD-0268

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. NASA Administrator Sean OKeefe gestures during a discussion with Florida government leaders about the location for NASAs new Shared Services Center. At left of OKeefe is U.S. Senator Bill Nelson; at right is Congressman Dave Weldon. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASAs payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The Florida location being proposed is of the Central Florida Research Park, near Orlando. Others attending the presentation included Congressman Tom Feeney, U.S. Representative Ric Keller, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

Hunter AAF, Savannah, Georgia. Revised Uniform Summary of Surface Weather Observations (RUSSWO)

DTIC Science & Technology

1970-11-18

Center of AIT/I.1Q-11 No Chile 13 Ft. to F~po 62 Rnwy 6 mar 62 Located 471 pt. 883 of Ros. No Chgc No Chile 15 Ft. to Feb 67 7 Mar 67 1. Located 300 Ft...N of lbwy 09 No Chile No Chile 25 Ft. o Feb 68 at 500 Ft Marker. 2. Located 300 Ft. N of Rawy 27 No Chile 15 Ft. at 500 Ft. Marker. 8 Mar 68 1...Located 500 Ft.from. Center Linc No Chile No Chile 20 Ft. May 70 and 1500 Pt from end of 1"w 95 2. Located 1100 Ft from Center Lir No Chge J-- 16 Ft and

The Presidential Initiative on Shared Early Warning

NASA Astrophysics Data System (ADS)

Pettis, Roy

2000-04-01

In September 1998, President Clinton and President Yeltsin issued a statement that our two countries would develop a system to share data from our respective early warning systems. The purpose of the initiative is to further reduce the risk of ballistic missile launches occurring in response to a misunderstanding about the data from such systems. The proposal includes a permanent center for sharing such data, located in Moscow, separate from but communicating with the strategic command-and-control centers of each country. It also includes development of a system of pre-launch notifications, which is expected to eventually provide notification of a broad class of launches, on a voluntary basis, including launches by all the countries that engage in missile and space activities. The status, progress, and prognosis for the work will be discussed. The presentation will address the experience gained from the operation of the Center for Y2K Strategic Stability in Colorado Springs (12/99 - 01/00), which tested many of our ideas for a joint center sharing both pre- launch and sensor data on worldwide launches. In addition, the potential of the initiative -- the first arms control effort involving active and continuing U.S.-Russian joint operations -- to provide a model for future arms control opportunities will be discussed.

Effect of higher rate of quintec for the control of powdery mildew on summer squash, 2012

USDA-ARS?s Scientific Manuscript database

The experiment was conducted at the Ohio Agricultural Research and Development Center’s Snyder Farm located in Wooster, OH on Wooster-Riddles silty clay loam soil, pH 6.0. On 2 May, the field was cultivated. On 15 May raised beds on 5 ft centers were prepared, laid with drip tape and plastic. On...

Effect of higher rate of quintec for the control of powdery mildew on cucumber, 2012

USDA-ARS?s Scientific Manuscript database

The experiment was conducted at the Ohio Agricultural Research and Development Center’s Snyder Farm located in Wooster, OH on Wooster-Riddles silty clay loam soil, pH 6.0. On 2 May, the field was cultivated. On 15 May raised beds on 5 ft centers were prepared, laid with drip tape and plastic. On...

Automated Welding System

NASA Technical Reports Server (NTRS)

Bayless, E. O.; Lawless, K. G.; Kurgan, C.; Nunes, A. C.; Graham, B. F.; Hoffman, D.; Jones, C. S.; Shepard, R.

1993-01-01

Fully automated variable-polarity plasma arc VPPA welding system developed at Marshall Space Flight Center. System eliminates defects caused by human error. Integrates many sensors with mathematical model of the weld and computer-controlled welding equipment. Sensors provide real-time information on geometry of weld bead, location of weld joint, and wire-feed entry. Mathematical model relates geometry of weld to critical parameters of welding process.

The influence of object shape and center of mass on grasp and gaze

PubMed Central

Desanghere, Loni; Marotta, Jonathan J.

2015-01-01

Recent experiments examining where participants look when grasping an object found that fixations favor the eventual index finger landing position on the object. Even though the act of picking up an object must involve complex high-level computations such as the visual analysis of object contours, surface properties, knowledge of an object’s function and center of mass (COM) location, these investigations have generally used simple symmetrical objects – where COM and horizontal midline overlap. Less research has been aimed at looking at how variations in object properties, such as differences in curvature and changes in COM location, affect visual and motor control. The purpose of this study was to examine grasp and fixation locations when grasping objects whose COM was positioned to the left or right of the objects horizontal midline (Experiment 1) and objects whose COM was moved progressively further from the midline of the objects based on the alteration of the object’s shape (Experiment 2). Results from Experiment 1 showed that object COM position influenced fixation locations and grasp locations differently, with fixations not as tightly linked to index finger grasp locations as was previously reported with symmetrical objects. Fixation positions were also found to be more central on the non-symmetrical objects. This difference in gaze position may provide a more holistic view, which would allow both index finger and thumb positions to be monitored while grasping. Finally, manipulations of COM distance (Experiment 2) exerted marked effects on the visual analysis of the objects when compared to its influence on grasp locations, with fixation locations more sensitive to these manipulations. Together, these findings demonstrate how object features differentially influence gaze vs. grasp positions during object interaction. PMID:26528207

Promoting Crew Autonomy: Current Advances and Novel Techniques

NASA Technical Reports Server (NTRS)

Harris, Samantha

2017-01-01

Since the dawn of the era of human space flight, mission control centers around the world have played an integral role in guiding space travelers toward mission success. In the International Space Station (ISS) program, astronauts and cosmonauts have the benefit of near constant access to the expertise and resources within mission control, as well as lifeboat capability to quickly return to Earth if something were to go wrong. As we move into an era of longer duration missions to more remote locations, rapid and ready access to mission control on earth will no longer be feasible. To prepare for such missions, long duration crews must be prepared to operate more autonomously, and the mission control paradigm that has been successfully employed for decades must be re-examined. The team at NASA's Payload Operations and Integration Center (POIC) in Huntsville, Alabama is playing an integral role in the development of concepts for a more autonomous long duration crew of the future via research on the ISS.

Association of Employee Attributes and Exceptional Performance Rating at a National Center of the US Centers for Disease Control and Prevention, 2011.

PubMed

Roberts, Henry; Myles, Ranell L; Truman, Benedict I; Dean, Hazel D

2015-01-01

Employee performance evaluation motivates and rewards exceptional individual performance that advances the achievement of organizational goals. The Centers for Disease Control and Prevention (CDC) and its operating units evaluate employee performance annually and reward exceptional performance with a cash award or quality step increase in pay. A summary performance rating (SPR) of "exceptional" indicated personal achievements in 2011 that were beyond expectations described in the employee's performance plan. To determine whether personal attributes and job setting of civil service employees were associated with an exceptional SPR in National Center for HIV/AIDS, Viral Hepatitis, STD, and TB Prevention (NCHHSTP) in 2011. Data from the CDC 2011 performance management database collected in 2012 were analyzed in 2013 to identify SPR, personal attributes, and job settings of full-time civil service employees. Multivariate logistic regression controlled for confounding and stratified analysis detected effect modifiers of the association between receiving an exceptional SPR in 2011 and gender, race/ethnicity, education, job location, job series, grade level, years in grade, years of federal service, supervisory role, and NCHHSTP division. Among the 1037 employees, exceptional SPR was independently associated with: female gender (adjusted odds ratio: 1.7 [1.3, 2.3]), advanced degrees (doctorate: 1.7 [1.1, 2.5] master's: [1.1, 2.0]), headquarters location (2.8 [1.9, 4.1]), higher pay grade (3.3 [2.4, 4.5]) and years in grade (0-1 years: 1.7 [1.3, 2.4]; 2-4 years: 1.5 [1.1, 2.0]), division level (Division A: 5.0 [2.5, 9.9]; Division B: 5.5 [3.5, 8.8]), and supervisory status (at a lower-pay grade) (odds ratio: 3.7 [1.1, 11.3]). Exceptional SPR is independently associated with personal employee attributes and job settings that are not modifiable by interventions designed to improve employee performance based on accomplishments.

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (center) and NASA Administrator Sean O’Keefe are deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson at left is Congressman Tom Feeney. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

NASA Image and Video Library

2004-02-19

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (center) and NASA Administrator Sean O’Keefe are deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson at left is Congressman Tom Feeney. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

46 CFR 28.535 - Inclining test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... section, each vessel for which the lightweight displacement and centers of gravity must be determined in... of the vessel which was inclined and the location of the longitudinal center of gravity differs less... characteristics can be made and the precise location of the position of the vessel's vertical center of gravity is...

46 CFR 28.535 - Inclining test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... section, each vessel for which the lightweight displacement and centers of gravity must be determined in... of the vessel which was inclined and the location of the longitudinal center of gravity differs less... characteristics can be made and the precise location of the position of the vessel's vertical center of gravity is...

46 CFR 28.535 - Inclining test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... section, each vessel for which the lightweight displacement and centers of gravity must be determined in... of the vessel which was inclined and the location of the longitudinal center of gravity differs less... characteristics can be made and the precise location of the position of the vessel's vertical center of gravity is...

Technology Insertion-Engineering Services Process Characterization, Task Order Number 1 (Block 1) Database Documentation Book, MANPGB

DTIC Science & Technology

1989-08-14

General Information > MANPGB is a Resource Control Center under the MANPG section of the Industrial W Products Division (MAN) at WR-ALC/ MANPGB is located...zo a N 1 I- I- LU ~a U) La ~ca LU P- 1= .: - "~0. ujN La7N LU 0 U 1I. DATE WORK CONTROL DOCUMENT . . . * ~:0IA~ r JOB ORDER NUMBER. 31J~ANTITY 4. N...30834A ---1.-- Cicleappropriate control number Clean iniao-xenlsrae. 02. Functional analysis - B- f 3 Deseal -Mt___ 04 Internal cleaning & visual. 05

Hazardous Waste Cleanup: Niagara Mohawk Power Corporation – Seventh North Service Center in Liverpool, New York

EPA Pesticide Factsheets

Niagara Mohawk Power Corporation (NMPC) - Seventh North Service Center is located on an approximately 119 acre-parcel of property located in the Town of Clay, Onondaga County, New York. The facility is located in an industrially zoned area, and is bordered

A hypothesis on the formation of the primary ossification centers in the membranous neurocranium: a mathematical and computational model.

PubMed

Garzón-Alvarado, Diego A

2013-01-21

This article develops a model of the appearance and location of the primary centers of ossification in the calvaria. The model uses a system of reaction-diffusion equations of two molecules (BMP and Noggin) whose behavior is of type activator-substrate and its solution produces Turing patterns, which represents the primary ossification centers. Additionally, the model includes the level of cell maturation as a function of the location of mesenchymal cells. Thus the mature cells can become osteoblasts due to the action of BMP2. Therefore, with this model, we can have two frontal primary centers, two parietal, and one, two or more occipital centers. The location of these centers in the simplified computational model is highly consistent with those centers found at an embryonic level. Copyright © 2012 Elsevier Ltd. All rights reserved.

Motion Path of the Instant Center of Rotation in the Cervical Spine During In Vivo Dynamic Flexion-Extension: Implications for Artificial Disc Design and Evaluation of Motion Quality Following Arthrodesis

PubMed Central

Anderst, William; Baillargeon, Emma; Donaldson, William; Lee, Joon; Kang, James

2013-01-01

Study Design Case-control. Objective To characterize the motion path of the instant center of rotation (ICR) at each cervical motion segment from C2 to C7 during dynamic flexion-extension in asymptomatic subjects. To compare asymptomatic and single-level arthrodesis patient ICR paths. Summary of Background Data The ICR has been proposed as an alternative to range of motion (ROM) for evaluating the quality of spine movement and for identifying abnormal midrange kinematics. The motion path of the ICR during dynamic motion has not been reported. Methods 20 asymptomatic controls, 12 C5/C6 and 5 C6/C7 arthrodesis patients performed full ROM flexion-extension while biplane radiographs were collected at 30 Hz. A previously validated tracking process determined three-dimensional vertebral position with sub-millimeter accuracy. The finite helical axis method was used to calculate the ICR between adjacent vertebrae. A linear mixed-model analysis identified differences in the ICR path among motion segments and between controls and arthrodesis patients. Results From C2/C3 to C6/C7, the mean ICR location moved superior for each successive motion segment (p < .001). The AP change in ICR location per degree of flexion-extension decreased from the C2/C3 motion segment to the C6/C7 motion segment (p < .001). Asymptomatic subject variability (95% CI) in the ICR location averaged ±1.2 mm in the SI direction and ±1.9 mm in the AP direction over all motion segments and flexion-extension angles. Asymptomatic and arthrodesis groups were not significantly different in terms of average ICR position (all p ≥ .091) or in terms of the change in ICR location per degree of flexion-extension (all p ≥ .249). Conclusions To replicate asymptomatic in vivo cervical motion, disc replacements should account for level-specific differences in the location and motion path of ICR. Single-level anterior arthrodesis does not appear to affect cervical motion quality during flexion-extension. PMID:23429677

Optimal location of radiation therapy centers with respect to geographic access.

PubMed

Santibáñez, Pablo; Gaudet, Marc; French, John; Liu, Emma; Tyldesley, Scott

2014-07-15

To develop a framework with which to evaluate locations of radiation therapy (RT) centers in a region based on geographic access. Patient records were obtained for all external beam radiation therapy started in 2011 for the province of British Columbia, Canada. Two metrics of geographic access were defined. The primary analysis was percentage of patients (coverage) within a 90-minute drive from an RT center (C90), and the secondary analysis was the average drive time (ADT) to an RT center. An integer programming model was developed to determine optimal center locations, catchment areas, and capacity required under different scenarios. Records consisted of 11,096 courses of radiation corresponding to 161,616 fractions. Baseline geographic access was estimated at 102.5 minutes ADT (each way, per fraction) and 75.9% C90. Adding 2 and 3 new centers increased C90 to 88% and 92%, respectively, and decreased ADT by between 43% and 61%, respectively. A scenario in which RT was provided in every potential location that could support at least 1 fully utilized linear accelerator resulted in 35.3 minutes' ADT and 93.6% C90. The proposed framework and model provide a data-driven means to quantitatively evaluate alternative configurations of a regional RT system. Results suggest that the choice of location for future centers can significantly improve geographic access to RT. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Development a heuristic method to locate and allocate the medical centers to minimize the earthquake relief operation time.

PubMed

Aghamohammadi, Hossein; Saadi Mesgari, Mohammad; Molaei, Damoon; Aghamohammadi, Hasan

2013-01-01

Location-allocation is a combinatorial optimization problem, and is defined as Non deterministic Polynomial Hard (NP) hard optimization. Therefore, solution of such a problem should be shifted from exact to heuristic or Meta heuristic due to the complexity of the problem. Locating medical centers and allocating injuries of an earthquake to them has high importance in earthquake disaster management so that developing a proper method will reduce the time of relief operation and will consequently decrease the number of fatalities. This paper presents the development of a heuristic method based on two nested genetic algorithms to optimize this location allocation problem by using the abilities of Geographic Information System (GIS). In the proposed method, outer genetic algorithm is applied to the location part of the problem and inner genetic algorithm is used to optimize the resource allocation. The final outcome of implemented method includes the spatial location of new required medical centers. The method also calculates that how many of the injuries at each demanding point should be taken to any of the existing and new medical centers as well. The results of proposed method showed high performance of designed structure to solve a capacitated location-allocation problem that may arise in a disaster situation when injured people has to be taken to medical centers in a reasonable time.

KSC-04pd0268

NASA Image and Video Library

2004-02-19

KENNEDY SPACE CENTER, FLA. - NASA Administrator Sean O’Keefe gestures during a discussion with Florida government leaders about the location for NASA’s new Shared Services Center. At left of O’Keefe is U.S. Senator Bill Nelson; at right is Congressman Dave Weldon. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The Florida location being proposed is of the Central Florida Research Park, near Orlando. Others attending the presentation included Congressman Tom Feeney, U.S. Representative Ric Keller, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

Aerial view of the Kennedy Space Center Visitor Center

NASA Technical Reports Server (NTRS)

1998-01-01

This Shuttle/Gantry mockup and Post Show Dome anchor the northeast corner of the Kennedy Space Center Visitor Complex. The Astronaut Memorial is located just above. Sprawling across 70 acres on Florida's Space Coast, the complex is located off State Road 405, NASA Parkway, six miles inside the Space Center entrance. The building at the upper left is the Theater Complex. Other exhibits and buildings on the site are the Center for Space Education, Cafeteria, Space Flight Exhibit Building, Souvenir Sales Building, Spaceport Central, Ticket Pavilion and Center for Space Education.

Sexual violence screening practices of student health centers located on universities in Florida.

PubMed

Halstead, Valerie; Williams, Jessica R; Gattamorta, Karina; Gonzalez-Guarda, Rosa

2017-01-01

The purpose of this study is to describe current sexual violence screening practices of student health centers located on universities in Florida. Institutional level data was collected from 33 student health centers from November 2015 through January 2016. The student health centers were located on public or private universities. A cross-sectional descriptive study design was used. Data was collected from student health center representatives through use of a telephone administered survey. Findings reveal that the majority of student health centers screen for sexual violence. However, not all use effective screening strategies. Further, the majority of screening questions used are not specific to sexual violence. Findings can be used to assist universities with responding to campus sexual violence among the college population. Recommendations for strengthening sexual violence screening practices and future research are provided.

Effectiveness of a Mobile Mammography Program.

PubMed

Stanley, Elizabeth; Lewis, Madelene C; Irshad, Abid; Ackerman, Susan; Collins, Heather; Pavic, Dag; Leddy, Rebecca J

2017-12-01

Mobile mammography units have increasingly been used to address patient health care disparities; however, there are limited data comparing mobile units to stationary sites. This study aims to evaluate the characteristics of women who underwent mammography screening in a mobile unit versus those who underwent mammography screening at a cancer center. In this retrospective study, we analyzed all screening mammography examinations performed in a mobile unit in 2014 (n = 1433 examinations). For comparison, we randomized and reviewed an equivalent number of screening mammography examinations performed at our cancer center in 2014 (n = 1434 examinations). BI-RADS assessment, adherence to follow-up, biopsies performed, cancer detection rate, and sociodemographic variables were recorded. An independent-samples t test was conducted to identify potential differences in age between cancer center patients and mobile unit patients. Chi-square analyses were used to test for associations between location and factors such as health insurance, race, marital status, geographic area, adherence to screening guidelines, recall rate, adherence to follow-up, and cancer detection rates. Patients visiting our cancer center (mean = 57.74 years; SD = 10.55) were significantly older than those visiting the mobile unit (mean = 52.58 years; SD = 8.19; p < 0.001). There was a significant association between location and health insurance status (χ 2 = 610.92; p < 0.001) with more uninsured patients undergoing screening in the mobile van (cancer center = 3.70%, mobile unit = 38.73%). There was a significant association between screening location and patient race (χ 2 = 118.75, p < 0.001), with more white patients being screened at the cancer center (cancer center = 47.28%, mobile unit = 33.30%), more black patients being screened in the mobile van (cancer center = 49.30%, mobile unit = 54.15%), and more Hispanic patients being screened in the mobile van (cancer center = 1.05%, mobile unit = 6.77%). There was a significant association between location and patient marital status (χ 2 = 135.61, p < 0.001), with more married patients screened at the cancer center (cancer center = 49.16%, mobile unit = 38.31%), more single patients screened in the mobile van (cancer center = 25.17%, mobile unit = 34.47%), and more widowed patients being screened at the cancer center (cancer center = 8.09%, mobile unit = 4.47%). There was a significant association between location and geographic area (χ 2 = 33.33, p < 0.001), with both locations reaching more urban than rural patients (cancer center = 79.99%, mobile unit = 70.62%). There was a significant association between location and adherence to screening guidelines (χ 2 = 179.60, p < 0.001), with patients screened at the cancer center being more compliant (cancer center = 56.90%, mobile unit = 34.47%). Finally, there was a significant association between location and recall rate (χ 2 = 4.06, p < 0.001). The cancer center had a lower recall rate (13.32%) than the mobile van (15.98%). Of those patients with BI-RADS 0, there was a significant association between location and adherence to follow-up (χ 2 = 22.75, p < 0.001) with patients using the mobile unit less likely to return for additional imaging (cancer center = 2.65%, mobile unit = 17.03%). Significant differences were found among patients visiting the cancer center versus the mobile mammography van. The cancer center's population is older and more adherent to guidelines, whereas the mobile mammography population exhibited greater racial and marital diversity, higher recall rate, and lack of adherence to follow-up recommendations. By identifying these characteristics, we can develop programs and materials that meet these populations' needs and behaviors, ultimately increasing mammography screening and follow-up rates among underserved populations.

75 FR 17126 - Foreign-Trade Zone 26-Atlanta, Georgia, Application for Expansion and Reorganization under...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

..., Jeffersonville (Twiggs County); Site 16 (308 acres) -- Meridian 75 Logistics Center, located at Interstate 75 and Rumble Road, Forsyth (Monroe County); Site 17 (193 acres) -- Majestic Airport Center III, located at... Futral Road, Griffin (Spalding County); Site 9 (321 acres) -- at the Hamilton Mill Business Center...

Rapid-Response Parenting Intervention in Diagnostic Centers as a Patient-Centered Innovation for Autism Spectrum Disorders

ERIC Educational Resources Information Center

McMillin, Stephen Edward; Bultas, Margaret W.; Wilmott, Jennifer; Grafeman, Sarah; Zand, Debra H.

2015-01-01

Parents of children newly diagnosed with autism spectrum disorders are a high-need population for whom skills-based parenting interventions likely help. Diagnostic centers are compelling locations to deliver parenting interventions because families are served in an accessible location and at a time they receive overwhelming treatment…

Failure of evidence-based cancer care in the United States: the association between rectal cancer treatment, cancer center volume, and geography.

PubMed

Monson, John R T; Probst, Christian P; Wexner, Steven D; Remzi, Feza H; Fleshman, James W; Garcia-Aguilar, Julio; Chang, George J; Dietz, David W

2014-10-01

This study examines recent adherence to recommended neoadjuvant chemoradiotherapy guidelines for patients with rectal cancer across geographic regions and institution volume and assesses trends over time. A recent report by the Institute of Medicine described US cancer care as chaotic. Cited deficiencies included wide variation in adherence to evidence-based guidelines even where clear consensus exists. Patients operated on for clinical stage II and III rectal cancer were selected from the 2006-2011 National Cancer Data Base. Multivariable logistic regressions were used to assess variation in chemotherapy and radiation use by cancer center type, geographical location, and hospital volume. The analysis controlled for patient age at diagnosis, sex, race/ethnicity, primary payer, average household income, average education, urban/rural classification of patient residence, comorbidity, and oncologic stage. There were 30,994 patients who met the inclusion criteria. Use of neoadjuvant radiation therapy and chemotherapy varied significantly by type of cancer center. The highest rates of adherence were observed in high-volume centers compared with low-volume centers (78% vs 69%; adjusted odds ratio = 1.46; P < 0.001). This variation is mirrored by hospital geographic location. Primary payer and year of diagnosis were not predictive of rates of neoadjuvant chemoradiotherapy. Adherence to evidence-based treatment guidelines in rectal cancer is suboptimal in the United States, with significant differences based on hospital volume and geographic regions. Little improvement has occurred in the last 5 years. These results support the implementation of standardized care pathways and a Centers of Excellence program for US patients with rectal cancer.

MISR Level 3 Imagery Overview

Atmospheric Science Data Center

2016-10-06

... is located at (90 N, 180 W) with the center of that grid cell being located at (89.75 N, 179.75 W). Conversely, the lower-right hand ... of the image is located at (90 S, 180 E) with that given cell being centered at (89.75 S, 179.75 E). In addition, select variances and ...

A power comparison of generalized additive models and the spatial scan statistic in a case-control setting.

PubMed

Young, Robin L; Weinberg, Janice; Vieira, Verónica; Ozonoff, Al; Webster, Thomas F

2010-07-19

A common, important problem in spatial epidemiology is measuring and identifying variation in disease risk across a study region. In application of statistical methods, the problem has two parts. First, spatial variation in risk must be detected across the study region and, second, areas of increased or decreased risk must be correctly identified. The location of such areas may give clues to environmental sources of exposure and disease etiology. One statistical method applicable in spatial epidemiologic settings is a generalized additive model (GAM) which can be applied with a bivariate LOESS smoother to account for geographic location as a possible predictor of disease status. A natural hypothesis when applying this method is whether residential location of subjects is associated with the outcome, i.e. is the smoothing term necessary? Permutation tests are a reasonable hypothesis testing method and provide adequate power under a simple alternative hypothesis. These tests have yet to be compared to other spatial statistics. This research uses simulated point data generated under three alternative hypotheses to evaluate the properties of the permutation methods and compare them to the popular spatial scan statistic in a case-control setting. Case 1 was a single circular cluster centered in a circular study region. The spatial scan statistic had the highest power though the GAM method estimates did not fall far behind. Case 2 was a single point source located at the center of a circular cluster and Case 3 was a line source at the center of the horizontal axis of a square study region. Each had linearly decreasing logodds with distance from the point. The GAM methods outperformed the scan statistic in Cases 2 and 3. Comparing sensitivity, measured as the proportion of the exposure source correctly identified as high or low risk, the GAM methods outperformed the scan statistic in all three Cases. The GAM permutation testing methods provide a regression-based alternative to the spatial scan statistic. Across all hypotheses examined in this research, the GAM methods had competing or greater power estimates and sensitivities exceeding that of the spatial scan statistic.

A power comparison of generalized additive models and the spatial scan statistic in a case-control setting

PubMed Central

2010-01-01

Background A common, important problem in spatial epidemiology is measuring and identifying variation in disease risk across a study region. In application of statistical methods, the problem has two parts. First, spatial variation in risk must be detected across the study region and, second, areas of increased or decreased risk must be correctly identified. The location of such areas may give clues to environmental sources of exposure and disease etiology. One statistical method applicable in spatial epidemiologic settings is a generalized additive model (GAM) which can be applied with a bivariate LOESS smoother to account for geographic location as a possible predictor of disease status. A natural hypothesis when applying this method is whether residential location of subjects is associated with the outcome, i.e. is the smoothing term necessary? Permutation tests are a reasonable hypothesis testing method and provide adequate power under a simple alternative hypothesis. These tests have yet to be compared to other spatial statistics. Results This research uses simulated point data generated under three alternative hypotheses to evaluate the properties of the permutation methods and compare them to the popular spatial scan statistic in a case-control setting. Case 1 was a single circular cluster centered in a circular study region. The spatial scan statistic had the highest power though the GAM method estimates did not fall far behind. Case 2 was a single point source located at the center of a circular cluster and Case 3 was a line source at the center of the horizontal axis of a square study region. Each had linearly decreasing logodds with distance from the point. The GAM methods outperformed the scan statistic in Cases 2 and 3. Comparing sensitivity, measured as the proportion of the exposure source correctly identified as high or low risk, the GAM methods outperformed the scan statistic in all three Cases. Conclusions The GAM permutation testing methods provide a regression-based alternative to the spatial scan statistic. Across all hypotheses examined in this research, the GAM methods had competing or greater power estimates and sensitivities exceeding that of the spatial scan statistic. PMID:20642827

Virtual collaborative environments: programming and controlling robotic devices remotely

NASA Astrophysics Data System (ADS)

Davies, Brady R.; McDonald, Michael J., Jr.; Harrigan, Raymond W.

1995-12-01

This paper describes a technology for remote sharing of intelligent electro-mechanical devices. An architecture and actual system have been developed and tested, based on the proposed National Information Infrastructure (NII) or Information Highway, to facilitate programming and control of intelligent programmable machines (like robots, machine tools, etc.). Using appropriate geometric models, integrated sensors, video systems, and computing hardware; computer controlled resources owned and operated by different (in a geographic sense as well as legal sense) entities can be individually or simultaneously programmed and controlled from one or more remote locations. Remote programming and control of intelligent machines will create significant opportunities for sharing of expensive capital equipment. Using the technology described in this paper, university researchers, manufacturing entities, automation consultants, design entities, and others can directly access robotic and machining facilities located across the country. Disparate electro-mechanical resources will be shared in a manner similar to the way supercomputers are accessed by multiple users. Using this technology, it will be possible for researchers developing new robot control algorithms to validate models and algorithms right from their university labs without ever owning a robot. Manufacturers will be able to model, simulate, and measure the performance of prospective robots before selecting robot hardware optimally suited for their intended application. Designers will be able to access CNC machining centers across the country to fabricate prototypic parts during product design validation. An existing prototype architecture and system has been developed and proven. Programming and control of a large gantry robot located at Sandia National Laboratories in Albuquerque, New Mexico, was demonstrated from such remote locations as Washington D.C., Washington State, and Southern California.

Design of a Solar Tracking System Using the Brightest Region in the Sky Image Sensor

PubMed Central

Wei, Ching-Chuan; Song, Yu-Chang; Chang, Chia-Chi; Lin, Chuan-Bi

2016-01-01

Solar energy is certainly an energy source worth exploring and utilizing because of the environmental protection it offers. However, the conversion efficiency of solar energy is still low. If the photovoltaic panel perpendicularly tracks the sun, the solar energy conversion efficiency will be improved. In this article, we propose an innovative method to track the sun using an image sensor. In our method, it is logical to assume the points of the brightest region in the sky image representing the location of the sun. Then, the center of the brightest region is assumed to be the solar-center, and is mathematically calculated using an embedded processor (Raspberry Pi). Finally, the location information on the sun center is sent to the embedded processor to control two servo motors that are capable of moving both horizontally and vertically to track the sun. In comparison with the existing sun tracking methods using image sensors, such as the Hough transform method, our method based on the brightest region in the sky image remains accurate under conditions such as a sunny day and building shelter. The practical sun tracking system using our method was implemented and tested. The results reveal that the system successfully captured the real sun center in most weather conditions, and the servo motor system was able to direct the photovoltaic panel perpendicularly to the sun center. In addition, our system can be easily and practically integrated, and can operate in real-time. PMID:27898002

Design of a Solar Tracking System Using the Brightest Region in the Sky Image Sensor.

PubMed

Wei, Ching-Chuan; Song, Yu-Chang; Chang, Chia-Chi; Lin, Chuan-Bi

2016-11-25

Solar energy is certainly an energy source worth exploring and utilizing because of the environmental protection it offers. However, the conversion efficiency of solar energy is still low. If the photovoltaic panel perpendicularly tracks the sun, the solar energy conversion efficiency will be improved. In this article, we propose an innovative method to track the sun using an image sensor. In our method, it is logical to assume the points of the brightest region in the sky image representing the location of the sun. Then, the center of the brightest region is assumed to be the solar-center, and is mathematically calculated using an embedded processor (Raspberry Pi). Finally, the location information on the sun center is sent to the embedded processor to control two servo motors that are capable of moving both horizontally and vertically to track the sun. In comparison with the existing sun tracking methods using image sensors, such as the Hough transform method, our method based on the brightest region in the sky image remains accurate under conditions such as a sunny day and building shelter. The practical sun tracking system using our method was implemented and tested. The results reveal that the system successfully captured the real sun center in most weather conditions, and the servo motor system was able to direct the photovoltaic panel perpendicularly to the sun center. In addition, our system can be easily and practically integrated, and can operate in real-time.

Neurons with object-centered spatial selectivity in macaque SEF: do they represent locations or rules?

PubMed

Tremblay, Léon; Gettner, Sonya N; Olson, Carl R

2002-01-01

In macaque monkeys performing a task that requires eye movements to the leftmost or rightmost of two dots in a horizontal array, some neurons in the supplementary eye field (SEF) fire differentially according to which side of the array is the target regardless of the array's location on the screen. We refer to these neurons as exhibiting selectivity for object-centered location. This form of selectivity might arise from involvement of the neurons in either of two processes: representing the locations of targets or representing the rules by which targets are selected. To distinguish between these possibilities, we monitored neuronal activity in the SEF of two monkeys performing a task that required the selection of targets by either an object-centered spatial rule or a color rule. On each trial, a sample array consisting of two side-by-side dots appeared; then a cue flashed on one dot; then the display vanished and a delay ensued. Next a target array consisting of two side-by-side dots appeared at an unpredictable location and another delay ensued; finally the monkey had to make an eye movement to one of the target dots. On some trials, the monkey had to select the dot on the same side as the cue (right or left). On other trials, he had to select the target of the same color as the cue (red or green). Neuronal activity robustly encoded the object-centered locations first of the cue and then of the target regardless of the whether the monkey was following a rule based on object-centered location or color. Neuronal activity was at most weakly affected by the type of rule the monkey was following (object-centered-location or color) or by the color of the cue and target (red or green). On trials involving a color rule, neuronal activity was moderately enhanced when the cue and target appeared on opposite sides of their respective arrays. We conclude that the general function of SEF neurons selective for object-centered location is to represent where the cue and target are in their respective arrays rather than to represent the rule for target selection.

The Malvinas War from the Argentinian Viewpoint

DTIC Science & Technology

1988-05-01

commercial concern is The Falkland Islands Company. This company owns 80 per cent of the total economic product. Communications are a considerable problem...krill also exists. Additionally, the islands’ strategic position is critical to control of the South Atlantic, with many commercial lines of communication ...the traditional 18 rivalry between services, and the poor communications network to receive orders from the decision centers located on the conti

Environmental Impact Statement. Peacekeeper Rail Garrison Program. Volume 1

DTIC Science & Technology

1989-02-01

Dupree Steve Coop Shannon Dupree Ernest Cooper Thomas W. Dupree Wainright Copass, Jr. Steve Dust Robert M. Corrie Dean Easton William Couchigian Arthur...located within the Shreveport- Texarkana -Tyler Interstate Air Quality Control Region (No. 022). There are no Prevention of Significant Deterioration Class...Master of Environmental Laws, National Law Center, The George Washington Univerqity, Washington, DC Years of Experience: 14 William R. Livingstone

Location in the right hemi-colon is an independent risk factor for delayed post-polypectomy hemorrhage: a multi-center case-control study.

PubMed

Buddingh, K Tim; Herngreen, Thomas; Haringsma, Jelle; van der Zwet, Wil C; Vleggaar, Frank P; Breumelhof, Ronald; Ter Borg, Frank

2011-06-01

Delayed hemorrhage is an infrequent, but serious complication of colonoscopic polypectomy. Large size is the only polyp-related factor that has been unequivocally proven to increase the risk of delayed bleeding. It has been suggested that location in the right hemi-colon is also a risk factor. The objective of this study was to determine whether polyp location is an independent risk factor for delayed post-polypectomy hemorrhage. A retrospective case-control study was conducted in two university hospitals and two community hospitals. Thirty-nine cases and 117 controls were identified. In multivariate analysis, size and location were found to be independent polyp-related risk factors for delayed type hemorrhage. The risk increased by 13% for every 1 mm increase in polyp diameter (odds ratio (OR) 1.13, 95% confidence interval (CI) 1.05-1.20, P<0.001). Polyps located in the right hemi-colon had an OR of 4.67 (1.88-11.61, P=0.001) for delayed hemorrhage. Polyps in the cecum seemed to be especially at high risk in univariate analysis (OR 13.82, 95% CI 2.66-71.73), but this could not be assessed in multivariate analysis as the number of cases was too small. Polyp type (sessile or pedunculated) was not a risk factor. Polyp location in the right hemi-colon seems to be an independent and substantial risk factor for delayed post-polypectomy hemorrhage. A low threshold for preventive hemostatic measures is advised when removing polyps from this region.

Surveying Local Health Departments and County Emergency Management Offices on Cooling Centers as a Heat Adaptation Resource in New York State.

PubMed

Nayak, Seema G; Lin, Shao; Sheridan, Scott C; Lu, Yi; Graber, Nathan; Primeau, Michael; Rafferty, Claudine Jones; Hwang, Syni-An

2017-02-01

Local agencies in New York State (NYS) set up cooling centers to provide relief from summer-time heat especially for people with limited access to air-conditioning. We aimed to determine cooling center locations in NYS, and explore county agencies' involvement in organizing and promoting utilization of cooling centers. We conducted a survey among county health and emergency preparedness offices in NYS (excluding NYC) and explored official county websites. We identified 377 cooling centers, mostly in metropolitan areas of NYS. Although 47 % of counties listed locations online, only 29 % reported locations via survey. Radio (90 %) and internet (84 %) were popular for information dissemination. Air-conditioning was available at all indoor cooling center facilities. Cooling centers in 13 % of the counties were accessible by either public transportation or shuttles arranged by the facility. About 38 % counties do not consider cooling centers important in their region or promote informal cooling centers. More than a third of New York counties had neither cooling centers nor plans to establish a cooling center as extreme heat was not perceived as a threat in their region.

Real-time graphics for the Space Station Freedom cupola, developed in the Systems Engineering Simulator

NASA Technical Reports Server (NTRS)

Red, Michael T.; Hess, Philip W.

1989-01-01

Among the Lyndon B. Johnson Space Center's responsibilities for Space Station Freedom is the cupola. Attached to the resource node, the cupola is a windowed structure that will serve as the space station's secondary control center. From the cupola, operations involving the mobile service center and orbital maneuvering vehicle will be conducted. The Systems Engineering Simulator (SES), located in building 16, activated a real-time man-in-the-loop cupola simulator in November 1987. The SES cupola is an engineering tool with the flexibility to evolve in both hardware and software as the final cupola design matures. Two workstations are simulated with closed-circuit television monitors, rotational and translational hand controllers, programmable display pushbuttons, and graphics display with trackball and keyboard. The displays and controls of the SES cupola are driven by a Silicon Graphics Integrated Raster Imaging System (IRIS) 4D/70 GT computer. Through the use of an interactive display builder program, SES, cupola display pages consisting of two dimensional and three dimensional graphics are constructed. These display pages interact with the SES via the IRIS real-time graphics interface. The focus is on the real-time graphics interface applications software developed on the IRIS.

Method and apparatus for strip casting

DOEpatents

Follstaedt, Donald W.; Powell, John C.; Sussman, Richard C.; Williams, Robert S.

1991-01-01

Casting nozzles will provide improved flow conditions with the parameters controlled according to the present invention. The gap relationships between the nozzle slot and exit orifice must be controlled in combination with converging exit passageway to provide a smooth flow without shearing and turbulence in the stream. The nozzle lips are also rounded to improve flow and increase refractory life of the lips of the nozzle. The tundish walls are tapered to provide improve flow for supplying the melt to the nozzle. The nozzle is located about 45.degree. below top dead center for optimum conditions.

An Adaptive H infinity Control Algorithm for Jitter Control and Target Tracking in a Directed Energy Weapon

DTIC Science & Technology

2012-05-16

large size and lack of efficiency of current technology after initial review. In the 1990’s the Air Force designed and produced a high- altitude ...Forden, G.E., "The airborne laser," Spectrum, IEEE , vol.34, no.9, pp.40-49, Sep 1997 10 altitude of 40,000 ft. the atmosphere was much clearer...distance remains the same. OT-5 provides a relative position of beam center on the detector. Two voltage outputs are given corresponding to x-axis location

Control coil arrangement for a rotating machine rotor

DOEpatents

Shah, Manoj R.; Lewandowsk, Chad R.

2001-07-31

A rotating machine (e.g., a turbine, motor or generator) is provided wherein a fixed solenoid or other coil configuration is disposed adjacent to one or both ends of the active portion of the machine rotor for producing an axially directed flux in the active portion so as to provide planar axial control at single or multiple locations for rotor balance, levitation, centering, torque and thrust action. Permanent magnets can be used to produce an axial bias magnetic field. The rotor can include magnetic disks disposed in opposed, facing relation to the coil configuration.

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (left front) and NASA Administrator Sean O’Keefe (right front) leave the Central Florida Research Park, near Orlando. Behind Nelson (at left) is Congressman Tom Feeney. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

NASA Image and Video Library

2004-02-19

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (left front) and NASA Administrator Sean O’Keefe (right front) leave the Central Florida Research Park, near Orlando. Behind Nelson (at left) is Congressman Tom Feeney. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

Real-time target tracking and locating system for UAV

NASA Astrophysics Data System (ADS)

Zhang, Chao; Tang, Linbo; Fu, Huiquan; Li, Maowen

2017-07-01

In order to achieve real-time target tracking and locating for UAV, a reliable processing system is built on the embedded platform. Firstly, the video image is acquired in real time by the photovoltaic system on the UAV. When the target information is known, KCF tracking algorithm is adopted to track the target. Then, the servo is controlled to rotate with the target, when the target is in the center of the image, the laser ranging module is opened to obtain the distance between the UAV and the target. Finally, to combine with UAV flight parameters obtained by BeiDou navigation system, through the target location algorithm to calculate the geodetic coordinates of the target. The results show that the system is stable for real-time tracking of targets and positioning.

Seismic reading taken at MSC recording impact of Apollo 13 S-IVB with surface

NASA Technical Reports Server (NTRS)

1970-01-01

A seismic reading taken from instruments at the Manned Spacecraft Center (MSC) recording impact of the Apollo 13 S-IVB/Instrument Unit with lunar surface. The expended Saturn third stage and instrument unit impacted the lunar surface at 7:09 p.m., April 14, 1970. The location of the impact was 2.4 degrees south latitude and 27.9 degrees west longitude, about 76 nautical miles west-northwest of the Apollo 12 Lunar Surface Experiment package deployment site. The S-IVB/IU impact was picked up by the Passive Seismic Experiment, a component of the package and transmitted to instruments at the Mission Control Center.

STS-44 Atlantis, OV-104, crewmembers participate in FB-SMS training at JSC

NASA Technical Reports Server (NTRS)

1991-01-01

STS-44 Atlantis, Orbiter Vehicle (OV) 104, Commander Frederick D. Gregory (left) and Pilot Terence T. Henricks (right), positioned at their appointed stations on the forward flight deck, are joined by Mission Specialist (MS) F. Story Musgrave (center). The crewmembers are participating in a flight simulation in the Fixed Base (FB) Shuttle Mission Simulator (SMS) located in JSC's Mission Simulation and Training Facility Bldg 5. Gregory in the commanders seat, Musgrave sitting on center console, and Henricks in the pilots seat look back toward the aft flight deck and the photographer. Seat backs appear in the foreground and forward control panels in the background.

KSC01padig024

NASA Image and Video Library

2001-01-19

KENNEDY SPACE CENTER, FLA. -- Space Shuttle Atlantis nears the Vehicle Assembly Building (left) and Launch Control Center on its way back from Launch Pad 39A. Atlantis is rolling back to the VAB so that workers can conduct inspections, make continuity checks and conduct X-ray analysis on the 36 solid rocket booster cables located inside each booster’s system tunnel. An extensive evaluation of NASA’s SRB cable inventory revealed conductor damage in four (of about 200) cables on the shelf. Shuttle managers decided to prove the integrity of the system tunnel cables already on Atlantis before launching Jan. 19. The launch has been rescheduled no earlier than Feb. 6

Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U

DOE PAGES

Boyer, M. D.; Battaglia, D. J.; Mueller, D.; ...

2018-01-25

Here, the upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U control system (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgradedmore » to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.« less

Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyer, M. D.; Battaglia, D. J.; Mueller, D.

Here, the upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U control system (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgradedmore » to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.« less

Plasma boundary shape control and real-time equilibrium reconstruction on NSTX-U

NASA Astrophysics Data System (ADS)

Boyer, M. D.; Battaglia, D. J.; Mueller, D.; Eidietis, N.; Erickson, K.; Ferron, J.; Gates, D. A.; Gerhardt, S.; Johnson, R.; Kolemen, E.; Menard, J.; Myers, C. E.; Sabbagh, S. A.; Scotti, F.; Vail, P.

2018-03-01

The upgrade to the National Spherical Torus eXperiment (NSTX-U) included two main improvements: a larger center-stack, enabling higher toroidal field and longer pulse duration, and the addition of three new tangentially aimed neutral beam sources, which increase available heating and current drive, and allow for flexibility in shaping power, torque, current, and particle deposition profiles. To best use these new capabilities and meet the high-performance operational goals of NSTX-U, major upgrades to the NSTX-U control system (NCS) hardware and software have been made. Several control algorithms, including those used for real-time equilibrium reconstruction and shape control, have been upgraded to improve and extend plasma control capabilities. As part of the commissioning phase of first plasma operations, the shape control system was tuned to control the boundary in both inner-wall limited and diverted discharges. It has been used to accurately track the requested evolution of the boundary (including the size of the inner gap between the plasma and central solenoid, which is a challenge for the ST configuration), X-point locations, and strike point locations, enabling repeatable discharge evolutions for scenario development and diagnostic commissioning.

Display Sharing: An Alternative Paradigm

NASA Technical Reports Server (NTRS)

Brown, Michael A.

2010-01-01

The current Johnson Space Center (JSC) Mission Control Center (MCC) Video Transport System (VTS) provides flight controllers and management the ability to meld raw video from various sources with telemetry to improve situational awareness. However, maintaining a separate infrastructure for video delivery and integration of video content with data adds significant complexity and cost to the system. When considering alternative architectures for a VTS, the current system's ability to share specific computer displays in their entirety to other locations, such as large projector systems, flight control rooms, and back supporting rooms throughout the facilities and centers must be incorporated into any new architecture. Internet Protocol (IP)-based systems also support video delivery and integration. IP-based systems generally have an advantage in terms of cost and maintainability. Although IP-based systems are versatile, the task of sharing a computer display from one workstation to another can be time consuming for an end-user and inconvenient to administer at a system level. The objective of this paper is to present a prototype display sharing enterprise solution. Display sharing is a system which delivers image sharing across the LAN while simultaneously managing bandwidth, supporting encryption, enabling recovery and resynchronization following a loss of signal, and, minimizing latency. Additional critical elements will include image scaling support, multi -sharing, ease of initial integration and configuration, integration with desktop window managers, collaboration tools, host and recipient controls. This goal of this paper is to summarize the various elements of an IP-based display sharing system that can be used in today's control center environment.

20 CFR 670.200 - Who decides where Job Corps centers will be located?

Code of Federal Regulations, 2014 CFR

2014-04-01

... 20 Employees' Benefits 4 2014-04-01 2014-04-01 false Who decides where Job Corps centers will be... LABOR (CONTINUED) THE JOB CORPS UNDER TITLE I OF THE WORKFORCE INVESTMENT ACT Site Selection and Protection and Maintenance of Facilities § 670.200 Who decides where Job Corps centers will be located? (a...

The Location of Community Mental Health Centers in Texas: Some Descriptions and Comparisons.

ERIC Educational Resources Information Center

Valdez, Ramiro

Part of a series of studies designed to lead to policy recommendations to improve mental health services to Mexican Americans in Texas, this monograph explores the availability and accessibility of community mental health centers (CMHCs) throughout the state. In hopes of explaining the underutilization of the centers statewide, the locations of…

Optimal Location of Radiation Therapy Centers With Respect to Geographic Access

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santibáñez, Pablo; Gaudet, Marc; French, John

2014-07-15

Purpose: To develop a framework with which to evaluate locations of radiation therapy (RT) centers in a region based on geographic access. Methods and Materials: Patient records were obtained for all external beam radiation therapy started in 2011 for the province of British Columbia, Canada. Two metrics of geographic access were defined. The primary analysis was percentage of patients (coverage) within a 90-minute drive from an RT center (C90), and the secondary analysis was the average drive time (ADT) to an RT center. An integer programming model was developed to determine optimal center locations, catchment areas, and capacity required undermore » different scenarios. Results: Records consisted of 11,096 courses of radiation corresponding to 161,616 fractions. Baseline geographic access was estimated at 102.5 minutes ADT (each way, per fraction) and 75.9% C90. Adding 2 and 3 new centers increased C90 to 88% and 92%, respectively, and decreased ADT by between 43% and 61%, respectively. A scenario in which RT was provided in every potential location that could support at least 1 fully utilized linear accelerator resulted in 35.3 minutes' ADT and 93.6% C90. Conclusions: The proposed framework and model provide a data-driven means to quantitatively evaluate alternative configurations of a regional RT system. Results suggest that the choice of location for future centers can significantly improve geographic access to RT.« less

Spontaneous Metacognition in Rhesus Monkeys.

PubMed

Rosati, Alexandra G; Santos, Laurie R

2016-09-01

Metacognition is the ability to think about thinking. Although monitoring and controlling one's knowledge is a key feature of human cognition, its evolutionary origins are debated. In the current study, we examined whether rhesus monkeys (Macaca mulatta; N = 120) could make metacognitive inferences in a one-shot decision. Each monkey experienced one of four conditions, observing a human appearing to hide a food reward in an apparatus consisting of either one or two tubes. The monkeys tended to search the correct location when they observed this baiting event, but engaged in information seeking-by peering into a center location where they could check both potential hiding spots-if their view had been occluded and information seeking was possible. The monkeys only occasionally approached the center when information seeking was not possible. These results show that monkeys spontaneously use information about their own knowledge states to solve naturalistic foraging problems, and thus provide the first evidence that nonhumans exhibit information-seeking responses in situations with which they have no prior experience. © The Author(s) 2016.

Station report on the Goddard Space Flight Center (GSFC) 1.2 meter telescope facility

NASA Technical Reports Server (NTRS)

Mcgarry, Jan F.; Zagwodzki, Thomas W.; Abbott, Arnold; Degnan, John J.; Cheek, Jack W.; Chabot, Richard S.; Grolemund, David A.; Fitzgerald, Jim D.

1993-01-01

The 1.2 meter telescope system was built for the Goddard Space Flight Center (GSFC) in 1973-74 by the Kollmorgen Corporation as a highly accurate tracking telescope. The telescope is an azimuth-elevation mounted six mirror Coude system. The facility has been used for a wide range of experimentation including helioseismology, two color refractometry, lunar laser ranging, satellite laser ranging, visual tracking of rocket launches, and most recently satellite and aircraft streak camera work. The telescope is a multi-user facility housed in a two story dome with the telescope located on the second floor above the experimenter's area. Up to six experiments can be accommodated at a given time, with actual use of the telescope being determined by the location of the final Coude mirror. The telescope facility is currently one of the primary test sites for the Crustal Dynamics Network's new UNIX based telescope controller software, and is also the site of the joint Crustal Dynamics Project / Photonics Branch two color research into atmospheric refraction.

Predicting worsening asthma control following the common cold

PubMed Central

Walter, Michael J.; Castro, Mario; Kunselman, Susan J.; Chinchilli, Vernon M; Reno, Melissa; Ramkumar, Thiruvamoor P.; Avila, Pedro C.; Boushey, Homer A.; Ameredes, Bill T.; Bleecker, Eugene R.; Calhoun, William J.; Cherniack, Reuben M.; Craig, Timothy J.; Denlinger, Loren C.; Israel, Elliot; Fahy, John V.; Jarjour, Nizar N.; Kraft, Monica; Lazarus, Stephen C.; Lemanske, Robert F.; Martin, Richard J.; Peters, Stephen P.; Ramsdell, Joe W.; Sorkness, Christine A.; Rand Sutherland, E.; Szefler, Stanley J.; Wasserman, Stephen I.; Wechsler, Michael E.

2008-01-01

The asthmatic response to the common cold is highly variable and early characteristics that predict worsening of asthma control following a cold have not been identified. In this prospective multi-center cohort study of 413 adult subjects with asthma, we used the mini-Asthma Control Questionnaire (mini-ACQ) to quantify changes in asthma control and the Wisconsin Upper Respiratory Symptom Survey-21 (WURSS-21) to measure cold severity. Univariate and multivariable models examined demographic, physiologic, serologic, and cold-related characteristics for their relationship to changes in asthma control following a cold. We observed a clinically significant worsening of asthma control following a cold (increase in mini-ACQ of 0.69 ± 0.93). Univariate analysis demonstrated season, center location, cold length, and cold severity measurements all associated with a change in asthma control. Multivariable analysis of the covariates available within the first 2 days of cold onset revealed the day 2 and the cumulative sum of the day 1 and 2 WURSS-21 scores were significant predictors for the subsequent changes in asthma control. In asthmatic subjects the cold severity measured within the first 2 days can be used to predict subsequent changes in asthma control. This information may help clinicians prevent deterioration in asthma control following a cold. PMID:18768579

Conducting Research on the International Space Station Using the EXPRESS Rack Facilities

NASA Technical Reports Server (NTRS)

Thompson, Sean W.; Lake, Robert E.

2013-01-01

Conducting Research on the International Space Station using the EXPRESS Rack Facilities. Sean W. Thompson and Robert E. Lake. NASA Marshall Space Flight Center, Huntsville, AL, USA. Eight "Expedite the Processing of Experiments to Space Station" (EXPRESS) Rack facilities are located within the International Space Station (ISS) laboratories to provide standard resources and interfaces for the simultaneous and independent operation of multiple experiments within each rack. Each EXPRESS Rack provides eight Middeck Locker Equivalent locations and two drawer locations for powered experiment equipment, also referred to as sub-rack payloads. Payload developers may provide their own structure to occupy the equivalent volume of one, two, or four lockers as a single unit. Resources provided for each location include power (28 Vdc, 0-500 W), command and data handling (Ethernet, RS-422, 5 Vdc discrete, +/- 5 Vdc analog), video (NTSC/RS 170A), and air cooling (0-200 W). Each rack also provides water cooling (500 W) for two locations, one vacuum exhaust interface, and one gaseous nitrogen interface. Standard interfacing cables and hoses are provided on-orbit. One laptop computer is provided with each rack to control the rack and to accommodate payload application software. Four of the racks are equipped with the Active Rack Isolation System to reduce vibration between the ISS and the rack. EXPRESS Racks are operated by the Payload Operations Integration Center at Marshall Space Flight Center and the sub-rack experiments are operated remotely by the investigating organization. Payload Integration Managers serve as a focal to assist organizations developing payloads for an EXPRESS Rack. NASA provides EXPRESS Rack simulator software for payload developers to checkout payload command and data handling at the development site before integrating the payload with the EXPRESS Functional Checkout Unit for an end-to-end test before flight. EXPRESS Racks began supporting investigations onboard ISS on April 24, 2001 and will continue through the life of the ISS.

The automation of an inlet mass flow control system

NASA Technical Reports Server (NTRS)

Supplee, Frank; Tcheng, Ping; Weisenborn, Michael

1989-01-01

The automation of a closed-loop computer controlled system for the inlet mass flow system (IMFS) developed for a wind tunnel facility at Langley Research Center is presented. This new PC based control system is intended to replace the manual control system presently in use in order to fully automate the plug positioning of the IMFS during wind tunnel testing. Provision is also made for communication between the PC and a host-computer in order to allow total animation of the plug positioning and data acquisition during the complete sequence of predetermined plug locations. As extensive running time is programmed for the IMFS, this new automated system will save both manpower and tunnel running time.

Transmission in situ and operando high temperature X-ray powder diffraction in variable gaseous environments

NASA Astrophysics Data System (ADS)

Schlicker, Lukas; Doran, Andrew; Schneppmüller, Peter; Gili, Albert; Czasny, Mathias; Penner, Simon; Gurlo, Aleksander

2018-03-01

This work describes a device for time-resolved synchrotron-based in situ and operando X-ray powder diffraction measurements at elevated temperatures under controllable gaseous environments. The respective gaseous sample environment is realized via a gas-tight capillary-in-capillary design, where the gas flow is achieved through an open-end 0.5 mm capillary located inside a 0.7 mm capillary filled with a sample powder. Thermal mass flow controllers provide appropriate gas flows and computer-controlled on-the-fly gas mixing capabilities. The capillary system is centered inside an infrared heated, proportional integral differential-controlled capillary furnace allowing access to temperatures up to 1000 °C.

76 FR 64112 - Privacy Act of 1974; Privacy Act System of Records Appendices

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

..., Greenbelt, MD 20771-0001. Location 5 Lyndon B. Johnson Space Center, National Aeronautics and Space... Center, MS 39529-6000. Location 19 NASA Wallops Flight Facility, Wallops Island, VA 23337. Appendix B...

The National Water Data Exchange (NAWDEX)

USGS Publications Warehouse

Edwards, Melvin D.

1977-01-01

The National Water Data Exchange (NAWDEX) was established in 1976 to assist users of water data to identify, locate, and acquire needed data. NAWDEX is a confederation of water-oriented organizations working together to provide more timely and convenient access to their data. A directory of sources of water data and a nationwide index of available water data are maintained for the storage and dissemination of information on available water data. Assistance services are provided through a nationwide network of Local Assistance Centers. This network consists of 51 Centers located in 45 states and Puerto Rico. The Centers provide convenient access to NAWDEX services as well as making local-area expertise available in the identification and location of needed data. Additional Centers will be added to the network, as needed, to meet demands. NAWDEX is centrally managed by a Program Office located within the U.S. Geological Survey 's Water Resources Division in Reston, Virginia. (Woodard-USGS)

Provision of Telemedicine Services by Community Health Centers

PubMed Central

Sharac, Jessica; Jacobs, Feygele

2014-01-01

The objective of this study was to assess the use of telemedicine services at community health centers. A national survey was distributed to all federally qualified health centers to gather data on their use of health information technology, including telemedicine services. Over a third of responding health centers (37%) provided some type of telemedicine service while 63% provided no telemedicine services. A further analysis that employed ANOVA and chi-square tests to assess differences by the provision of telemedicine services (provided no telemedicine services, provided one telemedicine service, and provided two or more telemedicine services) found that the groups differed by Meaningful Use compliance, location, percentage of elderly patients, mid-level provider, medical, and mental health staffing ratios, the percentage of patients with diabetes with good blood sugar control, and state and local funds per patient and per uninsured patient. This article presents the first national estimate of the use of telemedicine services at community health centers. Further study is needed to determine how to address factors, such as reimbursement and provider shortages, that may serve as obstacles to further expansion of telemedicine services use by community health centers. PMID:25422721

Kinesthetic control simulator. [for pilot training

NASA Technical Reports Server (NTRS)

Hill, P. R.; Thomas, D. F., Jr. (Inventor)

1975-01-01

A kinesthetic control simulator is reported that has a flat base upon which rests a support structure having a lower spherical surface for rotation on the base plate with columns which support a platform above the support structure at a desired location with respect to the center of curvature of the spherical surface. A handrail is at approximately the elevation of the hips of the operator above the platform with a ring attached to the support structure which may be used to limit the angle of tilt. Five degree freedom-of-motion can be obtained by utilizing an air pad structure for support of the control simulator.

Data Acquisition Systems

NASA Technical Reports Server (NTRS)

1994-01-01

In the mid-1980s, Kinetic Systems and Langley Research Center determined that high speed CAMAC (Computer Automated Measurement and Control) data acquisition systems could significantly improve Langley's ARTS (Advanced Real Time Simulation) system. The ARTS system supports flight simulation R&D, and the CAMAC equipment allowed 32 high performance simulators to be controlled by centrally located host computers. This technology broadened Kinetic Systems' capabilities and led to several commercial applications. One of them is General Atomics' fusion research program. Kinetic Systems equipment allows tokamak data to be acquired four to 15 times more rapidly. Ford Motor company uses the same technology to control and monitor transmission testing facilities.

Infrasound Monitoring of Local, Regional and Global Events

DTIC Science & Technology

2007-09-01

detect and associate signals from the March 9th 2005 eruption at Mount Saint Helens, and locate the event to be within 5 km of the caldera . The...are located within 5 km of the center of the caldera at Mount Saint Helens. Figure 4. Locations of grid nodes that were automatically associated...photograph, and are located within 5 km of the center of the caldera . 29th Monitoring Research Review: Ground-Based Nuclear Explosion Monitoring

Infection prevention and control practice for Crimean-Congo hemorrhagic fever-A multi-center cross-sectional survey in Eurasia.

PubMed

Fletcher, Tom E; Gulzhan, Abuova; Ahmeti, Salih; Al-Abri, Seif S; Asik, Zahide; Atilla, Aynur; Beeching, Nick J; Bilek, Heval; Bozkurt, Ilkay; Christova, Iva; Duygu, Fazilet; Esen, Saban; Khanna, Arjun; Kader, Çiğdem; Mardani, Masoud; Mahmood, Faisal; Mamuchishvili, Nana; Pshenichnaya, Natalia; Sunbul, Mustafa; Yalcin, Tuğba Y; Leblebicioglu, Hakan

2017-01-01

Crimean Congo Hemorrhagic Fever (CCHF) is a life threatening acute viral infection that presents significant risk of nosocomial transmission to healthcare workers. Evaluation of CCHF infection prevention and control (IP&C) practices in healthcare facilities that routinely manage CCHF cases in Eurasia. A cross-sectional CCHF IP&C survey was designed and distributed to CCHF centers in 10 endemic Eurasian countries in 2016. Twenty-three responses were received from centers in Turkey, Pakistan, Russia, Georgia, Kosovo, Bulgaria, Oman, Iran, India and Kazakhstan. All units had dedicated isolation rooms for CCHF, with cohorting of confirmed cases in 15/23 centers and cohorting of suspect and confirmed cases in 9/23 centers. There was adequate personal protective equipment (PPE) in 22/23 facilities, with 21/23 facilities reporting routine use of PPE for CCHF patients. Adequate staffing levels to provide care reported in 14/23 locations. All centers reported having a high risk CCHFV nosocomial exposure in last five years, with 5 centers reporting more than 5 exposures. Education was provided annually in most centers (13/23), with additional training requested in PPE use (11/23), PPE donning/doffing (12/23), environmental disinfection (12/23) and waste management (14/23). Staff and patient safety must be improved and healthcare associated CCHF exposure and transmission eliminated. Improvements are recommended in isolation capacity in healthcare facilities, use of PPE and maintenance of adequate staffing levels. We recommend further audit of IP&C practice at individual units in endemic areas, as part of national quality assurance programs.

Infection prevention and control practice for Crimean-Congo hemorrhagic fever—A multi-center cross-sectional survey in Eurasia

PubMed Central

Gulzhan, Abuova; Ahmeti, Salih; Al-Abri, Seif S.; Asik, Zahide; Atilla, Aynur; Beeching, Nick J.; Bilek, Heval; Bozkurt, Ilkay; Christova, Iva; Duygu, Fazilet; Esen, Saban; Khanna, Arjun; Kader, Çiğdem; Mardani, Masoud; Mahmood, Faisal; Mamuchishvili, Nana; Pshenichnaya, Natalia; Sunbul, Mustafa; Yalcin, Tuğba Y.; Leblebicioglu, Hakan

2017-01-01

Background Crimean Congo Hemorrhagic Fever (CCHF) is a life threatening acute viral infection that presents significant risk of nosocomial transmission to healthcare workers. Aim Evaluation of CCHF infection prevention and control (IP&C) practices in healthcare facilities that routinely manage CCHF cases in Eurasia. Methods A cross-sectional CCHF IP&C survey was designed and distributed to CCHF centers in 10 endemic Eurasian countries in 2016. Results Twenty-three responses were received from centers in Turkey, Pakistan, Russia, Georgia, Kosovo, Bulgaria, Oman, Iran, India and Kazakhstan. All units had dedicated isolation rooms for CCHF, with cohorting of confirmed cases in 15/23 centers and cohorting of suspect and confirmed cases in 9/23 centers. There was adequate personal protective equipment (PPE) in 22/23 facilities, with 21/23 facilities reporting routine use of PPE for CCHF patients. Adequate staffing levels to provide care reported in 14/23 locations. All centers reported having a high risk CCHFV nosocomial exposure in last five years, with 5 centers reporting more than 5 exposures. Education was provided annually in most centers (13/23), with additional training requested in PPE use (11/23), PPE donning/doffing (12/23), environmental disinfection (12/23) and waste management (14/23). Conclusions Staff and patient safety must be improved and healthcare associated CCHF exposure and transmission eliminated. Improvements are recommended in isolation capacity in healthcare facilities, use of PPE and maintenance of adequate staffing levels. We recommend further audit of IP&C practice at individual units in endemic areas, as part of national quality assurance programs. PMID:28886039

77 FR 65596 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-29

... to offer remote multi-cast ITCH Wave Ports for clients co-located at other third party data centers... delivery of third party market data to market center clients via a wireless network using millimeter wave... Multi- cast ITCH Wave Ports for clients co-located at other third-party data centers, through which...

High angle-of-attack aerodynamics of a strake-canard-wing V/STOL fighter configuration

NASA Technical Reports Server (NTRS)

Durston, D. A.; Schreiner, J. A.

1983-01-01

High angle-of-attack aerodynamic data are analyzed for a strake-canard-wing V/STOL fighter configuration. The configuration represents a twin-engine supersonic V/STOL fighter aircraft which uses four longitudinal thrust-augmenting ejectors to provide vertical lift. The data were obtained in tests of a 9.39 percent scale model of the configuration in the NASA Ames 12-Foot Pressure Wind Tunnel, at a Mach number of 0.2. Trimmed aerodynamic characteristics, longitudinal control power, longitudinal and lateral/directional stability, and effects of alternate strake and canard configurations are analyzed. The configuration could not be trimmed (power-off) above 12 deg angle of attack because of the limited pitch control power and the high degree of longitudinal instability (28 percent) at this Mach number. Aerodynamic center location was found to be controllable by varying strake size and canard location without significantly affecting lift and drag. These configuration variations had relatively little effect on the lateral/directional stability up to 10 deg angle of attack.

Sexual orientation and spatial position effects on selective forms of object location memory.

PubMed

Rahman, Qazi; Newland, Cherie; Smyth, Beatrice Mary

2011-04-01

Prior research has demonstrated robust sex and sexual orientation-related differences in object location memory in humans. Here we show that this sexual variation may depend on the spatial position of target objects and the task-specific nature of the spatial array. We tested the recovery of object locations in three object arrays (object exchanges, object shifts, and novel objects) relative to veridical center (left compared to right side of the arrays) in a sample of 35 heterosexual men, 35 heterosexual women, and 35 homosexual men. Relative to heterosexual men, heterosexual women showed better location recovery in the right side of the array during object exchanges and homosexual men performed better in the right side during novel objects. However, the difference between heterosexual and homosexual men disappeared after controlling for IQ. Heterosexual women and homosexual men did not differ significantly from each other in location change detection with respect to task or side of array. These data suggest that visual space biases in processing categorical spatial positions may enhance aspects of object location memory in heterosexual women. Copyright © 2010 Elsevier Inc. All rights reserved.

An Active Damping at Blade Resonances Using Piezoelectric Transducers

NASA Technical Reports Server (NTRS)

Choi, Benjamin; Morrison, Carlos; Duffy, Kirsten

2008-01-01

The NASA Glenn Research Center (GRC) is developing an active damping at blade resonances using piezoelectric structure to reduce excessive vibratory stresses that lead to high cycle fatigue (HCF) failures in aircraft engine turbomachinery. Conventional passive damping work was shown first on a nonrotating beam made by Ti-6A1-4V with a pair of identical piezoelectric patches, and then active feedback control law was derived in terms of inductor, resister, and capacitor to control resonant frequency only. Passive electronic circuit components and adaptive feature could be easily programmable into control algorithm. Experimental active damping was demonstrated on two test specimens achieving significant damping on tip displacement and patch location. Also a multimode control technique was shown to control several modes.

Bottom Interaction in Long Range Acoustic Propagation

DTIC Science & Technology

2006-09-30

Pacific Ocean utilizing controlled sources and vertical and horizontal receiver arrays . Broadband sources are considered with typical center...The LOAPEX (Long-range Ocean Acoustic Propagation Experiment) vertical line arrays (VLA) are described on page 1 of the LOAPEX cruise report: " The...hydrophone arrays on the two combined VLAs covered most of the 5-km water column. We refer to one of the VLAs as the deep VLA (DVLA), located at

Improving the seismic torsional behavior of plan-asymmetric, single-storey, concrete moment resisting buildings with fluid viscous dampers

NASA Astrophysics Data System (ADS)

Rofooei, Fayaz Rahimzadeh; Mohammadzadeh, Sahar

2016-03-01

The optimal distribution of fluid viscous dampers (FVD) in controlling the seismic response of eccentric, single-storey, moment resisting concrete structures is investigated using the previously defined center of damping constant (CDC). For this purpose, a number of structural models with different one-way stiffness and strength eccentricities are considered. Extensive nonlinear time history analyses are carried out for various arrangements of FVDs. It is shown that the arrangement of FVDs for controlling the torsional behavior due to asymmetry in the concrete structures is very dependent on the intensity of the peak ground acceleration (PGA) and the extent of the structural stiffness and strength eccentricities. The results indicate that, in the linear range of structural behavior the stiffness eccentricity es which is the main parameter in determining the location of optimal CDC, is found to be less or smaller than the optimal damping constant eccentricity e*d, i.e., |e*d| > |es|. But, in the nonlinear range of structural behavior where the strength eccentricity er is the dominant factor in determining the location of optimal CDC, |e*d| > |er|. It is also concluded that for the majority of the plan-asymmetric, concrete structures considered in this study with er ≠ 0, the optimal CDC approaches the center of mass as er decreases.

Leon M. Lederman Science Education Center: General Information

Science.gov Websites

field trips. Location: Located at Fermilab about 35 miles west of Chicago, the Center is easily accessible from the Fermilab main entrance at Kirk Road and Pine Street in Batavia, just three miles north of

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (left foreground) and NASA Administrator Sean O’Keefe (right) look deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson is Congressman Tom Feeney and Center Director Jim Kennedy. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

NASA Image and Video Library

2004-02-19

KENNEDY SPACE CENTER, FLA. - U.S. Senator Bill Nelson (left foreground) and NASA Administrator Sean O’Keefe (right) look deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson is Congressman Tom Feeney and Center Director Jim Kennedy. The research park is being proposed as the location for NASA’s new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

In-Field Diffuse Ultraviolet Spectroscopy and Imaging of the Stardust Sample Return Capsule

NASA Technical Reports Server (NTRS)

Pugel, D. Elizabeth; Stackpoole, Mairead; McNamara, Karen; Schwartz, C.; Warren, J.; Kontinos, Dean

2008-01-01

In-field diffuse Ultraviolet (UV) spectroscopy and imaging systems were developed for the purposes of evaluating the surface chemical composition of spacecraft thermal control coatings and materials. The investigation of these systems and the compilation of an associated UV reflectance and luminescence database were conducted using the Stardust Sample Return Capsule (SRC), located at the Johnson Space Center. Spectral responses of the surfaces of the Stardust forebody and aftbody in both reflectance and fluorescence modes were examined post-flight. In this paper, we report on two primary findings of in-field diffuse UV spectroscopy and imaging: (1) deduction of the thermal history of thermal control coatings of the forebody and (2) bond line variations in the aftbody. In the forebody, the thermal history of thermal control coatings may be deduced from the presence of particular semiconducting defect states associated with ZnO, a common emissivity constituent in thermal control coatings. A spatial dependence of this history was mapped for these regions. In the aftbody, luminescing defect states, associated with Si and SiO2 color centers were found along regions of bond variability.

KSC-98pc1059

NASA Image and Video Library

1998-08-06

This Shuttle/Gantry mockup and Post Show Dome anchor the northeast corner of the Kennedy Space Center Visitor Complex. The Astronaut Memorial is located just above. Sprawling across 70 acres on Florida's Space Coast, the complex is located off State Road 405, NASA Parkway, six miles inside the Space Center entrance. The building at the upper left is the Theater Complex. Other exhibits and buildings on the site are the Center for Space Education, Cafeteria, Space Flight Exhibit Building, Souvenir Sales Building, Spaceport Central, Ticket Pavilion and Center for Space Education

Western Aeronautical Test Range

NASA Technical Reports Server (NTRS)

Sakahara, Robert D.

2008-01-01

NASA's Western Aeronautical Test Range (WATR) is a network of facilities used to support aeronautical research, science missions, exploration system concepts, and space operations. The WATR resides at NASA's Dryden Flight Research Center located at Edwards Air Force Base, California. The WATR is a part of NASA's Corporate Management of Aeronautical Facilities and funded by the Strategic Capability Asset Program (SCAP). It is managed by the Aeronautics Test Program (ATP) of the Aeronautics Research Mission Directorate (ARMD) to provide the right facility at the right time. NASA is a tenant on Edwards Air Force Base and has an agreement with the Air Force Flight Test Center to use the land and airspace controlled by the Department of Defense (DoD). The topics include: 1) The WATR supports a variety of vehicles; 2) Dryden shares airspace with the AFFTC; 3) Restricted airspace, corridors, and special use areas are available for experimental aircraft; 4) WATR Products and Services; 5) WATR Support Configuration; 6) Telemetry Tracking; 7) Time Space Positioning; 8) Video; 9) Voice Communication; 10) Mobile Operations Facilities; 11) Data Processing; 12) Mission Control Center; 13) Real-Time Data Analysis; and 14) Range Safety.

The NASA Lewis Research Center: An Economic Impact Study

NASA Technical Reports Server (NTRS)

Austrian, Ziona

1996-01-01

The NASA Lewis Research Center (LeRC), established in 1941, is one of ten NASA research centers in the country. It is situated on 350 acres of land in Cuyahoga County and occupies more than 140 buildings and over 500 specialized research and test facilities. Most of LeRC's facilities are located in the City of Cleveland; some are located within the boundaries of the cities of Fairview Park and Brookpark. LeRC is a lead center for NASA's research, technology, and development in the areas of aeropropulsion and selected space applications. It is a center of excellence for turbomachinery, microgravity fluid and combustion research, and commercial communication. The base research and technology disciplines which serve both aeronautics and space areas include materials and structures, instrumentation and controls, fluid physics, electronics, and computational fluid dynamics. This study investigates LeRC's economic impact on Northeast Ohio's economy. It was conducted by The Urban Center's Economic Development Program in Cleveland State University's Levin College of Urban Affairs. The study measures LeRC's direct impact on the local economy in terms of jobs, output, payroll, and taxes, as well as the indirect impact of these economic activities when they 'ripple' throughout the economy. To fully explain LeRC's overall impact on the region, its contributions in the areas of technology transfer and education are also examined. The study uses a highly credible and widely accepted research methodology. First, regional economic multipliers based on input-output models were used to estimate the effect of LERC spending on the Northeast Ohio economy. Second, the economic models were complemented by interviews with industrial, civic, and university leaders to qualitatively assess LeRC's impact in the areas of technology transfer and education.

Near-Surface Profiles of Water Stable Isotope Components and Indicated Transitional History of Ice-Wedge Polygons Near Barrow

NASA Astrophysics Data System (ADS)

Iwahana, G.; Wilson, C.; Newman, B. D.; Heikoop, J. M.; Busey, R.

2017-12-01

Wetlands associated with ice-wedge polygons are commonly distributed across the Arctic Coastal Plain of northern Alaska, a region underlain by continuous permafrost. Micro-topography of the ice-wedge polygons controls local hydrology, and the micro-topography could be altered due to factors such like surface vegetation, wetness, freeze-thaw cycles, and permafrost degradation/aggradation under climate change. Understanding status of the wetlands in the near future is important because it determines biogeochemical cycle, which drives release of greenhouse gases from the ground. However, transitional regime of the ice-wedge polygons under the changing climate is not fully understood. In this study, we analyzed geochemistry of water extracted from frozen soil cores sampled down to about 1m depth in 2014 March at NGEE-Arctic sites in the Barrow Environmental Observatory. The cores were sampled from troughs/rims/centers of five different low-centered or flat-centered polygons. The frozen cores are divided into 5-10cm cores for each location, thawed in sealed plastic bags, and then extracted water was stored in vials. Comparison between the profiles of geochemistry indicated connection of soil water in the active layer at different location in a polygon, while it revealed that distinctly different water has been stored in permafrost layer at troughs/rims/centers of some polygons. Profiles of volumetric water content (VWC) showed clear signals of freeze-up desiccation in the middle of saturated active layers as low VWC anomalies at most sampling points. Water in the active layer and near-surface permafrost was classified into four categories: ice wedge / fresh meteoric / transitional / highly fractionated water. The overall results suggested prolonged separation of water in the active layer at the center of low-centered polygons without lateral connection in water path in the past.

THE EPIDEMIOLOGY OF EMERGENCY DEPARTMENT THORACOTOMY IN A STATEWIDE TRAUMA SYSTEM: DOES CENTER VOLUME MATTER?

PubMed

Dumas, Ryan P; Seamon, Mark J; Smith, Brian P; Yang, Wei; Cannon, Jeremy W; Schwab, C William; Reilly, Patrick M; Holena, Daniel N

2018-04-17

The relationship between high volume and improved outcomes has been described for a host of elective high-impact, low-frequency procedures, but there are little data to support such a relationship in high-impact low-frequency procedures in trauma. Using emergency department thoracotomy (EDT) as a model, we hypothesized that patients presenting to centers with higher institutional volumes of EDT would have improved survival referent to those presenting to lower volume institutions. We queried the Pennsylvania Trauma Outcomes Study (PTOS) registry from 2007-2015 for all EDTs performed at level I and II centers identified by ICD-9 procedure codes and a location stamp indicating the emergency department. We examined patient-level risk factors for survival in univariate regression and multivariable regression models. Centers were divided into tertiles of mean annual EDT volume and the association between mean annual EDT volume and patient survival was examined using logistic regression after controlling for patient factors. 1,399 emergency department thoracotomies were performed at 28 centers. Overall survival was 6.8%. After controlling for patient age, mechanism of injury, signs of life, and injury severity, patients presenting to centers in the highest tertile of volume had significantly higher odds of survival compared to patients presenting to centers in the lowest tertile of volume (OR 4.56, 95% CI 1.43-14.50). Patients presenting to centers with higher mean annual volume of EDTs have improved survival compared to those presenting to institutions with lower mean annual EDT volume. Efforts to understand the etiology of this finding may lead to interventions to improve outcomes at lower volume centers. Level 3: Retrospective cohort study.

STS-112 crew with President of Ajara in Georgia (Russia)

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- In the Operations and Checkout Building, Aslan Abashidze (right), President of the Autonomous Republic of Ajara in Georgia (Russia), visits with the STS-112 crew. From left, they are Mission Specialist Piers J. Sellers; Pilot Pamela Ann Melroy; Mission Specialist Fyodor N. Yurchikhin, a cosmonaut with the Russian Space Agency; Mission Specialist Sandra H. Magnus; and CommanderJeffrey S. Ashby. Mission Specialist David A. Wolf, not pictured, is also a member of the crew. The crew is awaiting launch on mission STS-112 to the International Space Station aboard Space Shuttle Atlantis. The launch has been postponed to no earlier than Monday, Oct. 7, so that the Mission Control Center, located at the Lyndon B. Johnson Space Center in Houston, Texas, can be secured and protected from potential storm impacts from Hurricane Lili.

Oblique Wing Research Aircraft on ramp

NASA Technical Reports Server (NTRS)

1976-01-01

This 1976 photograph of the Oblique Wing Research Aircraft was taken in front of the NASA Flight Research Center hangar, located at Edwards Air Force Base, California. In the photograph the noseboom, pitot-static probe, and angles-of-attack and sideslip flow vanes(covered-up) are attached to the front of the vehicle. The clear nose dome for the television camera, and the shrouded propellor for the 90 horsepower engine are clearly seen. The Oblique Wing Research Aircraft was a small, remotely piloted, research craft designed and flight tested to look at the aerodynamic characteristics of an oblique wing and the control laws necessary to achieve acceptable handling qualities. NASA Dryden Flight Research Center and the NASA Ames Research Center conducted research with this aircraft in the mid-1970s to investigate the feasibility of flying an oblique wing aircraft.

A Transdisciplinary Training Program for Behavioral Oncology and Cancer Control Scientists

PubMed Central

McDaniel, Anna M.; Champion, Victoria L.; Kroenke, Kurt

2008-01-01

Transdisciplinary health research training has been identified as a major initiative to achieve the vision for research teams of the future as articulated in the NIH Roadmap for Medical Research. To address the need for scientists who can integrate diverse scientific approaches and work in transdisciplinary teams to solve complex health problems, Indiana University has designed an innovative training program that will provide the didactic and research experiences to enable trainees to establish productive careers in behavioral oncology and cancer control research. Development of a successful transdisciplinary training program requires mentorship, research, and a specialized curriculum that encompass a broad range of disciplines. The program capitalizes on a unique set of existing and emerging training opportunities resulting from the collaborative activities of the Indiana University (IU) Simon Cancer Center, the IU Schools of Nursing and Medicine, and multiple research institutes and academic centers located in Indiana and neighboring states. PMID:18501750

The epigenetic control of the Athila family of retrotransposons in Arabidopsis.

PubMed

Slotkin, R Keith

2010-08-16

Retrotransposons are major constituents of both plant and animal genomes. In the genome of the model plant Arabidopsis thaliana, which is known for its small size and low repeat content, the Athila retrotransposon family occupies over 2.7% of the total genome and is a major building block of the centromere. However, the copy number and location of Athila elements fail to tell the complete story, as recent experiments have demonstrated that Athila is not only literally at the center of each chromosome, but figuratively at the center of Arabidopsis epigenetic regulation. The silencing of Athila retrotransposons has come to the forefront of Arabidopsis small RNA regulation, the control of the centromere core, as well as potentially playing a role in speciation. This review explores what studying one of the largest transposable element families in one of the smallest plant genomes can tell us about the epigenetic regulation of the genome.

Protein Crystal Growth

NASA Technical Reports Server (NTRS)

2003-01-01

In order to rapidly and efficiently grow crystals, tools were needed to automatically identify and analyze the growing process of protein crystals. To meet this need, Diversified Scientific, Inc. (DSI), with the support of a Small Business Innovation Research (SBIR) contract from NASA s Marshall Space Flight Center, developed CrystalScore(trademark), the first automated image acquisition, analysis, and archiving system designed specifically for the macromolecular crystal growing community. It offers automated hardware control, image and data archiving, image processing, a searchable database, and surface plotting of experimental data. CrystalScore is currently being used by numerous pharmaceutical companies and academic and nonprofit research centers. DSI, located in Birmingham, Alabama, was awarded the patent Method for acquiring, storing, and analyzing crystal images on March 4, 2003. Another DSI product made possible by Marshall SBIR funding is VaporPro(trademark), a unique, comprehensive system that allows for the automated control of vapor diffusion for crystallization experiments.

75 FR 17161 - Job Corps: Preliminary Finding of No Significant Impact (FONSI) for the Installation of a Small...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... Impact (FONSI) for the Installation of a Small Wind Turbine at the Pine Ridge Job Corps Center Located at...: Preliminary Finding of No Significant Impact (FONSI) for a small Wind Turbine Installation to be located at... prepared for a proposed Wind Turbine Installation to be located at the Pine Ridge Job Corps Center, 15710...

78 FR 77765 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

...-location services allow Users to rent space in the data center so they may locate their electronic servers... Cabinets A User is able to request a physical cabinet to house its servers and other equipment in the data... order gateway, regardless of whether the sender is co-located in the data center or not. In addition, co...

58. VIEW OF SIGNAL BUS SECTION NUMBER 2 LOCATED OVER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

58. VIEW OF SIGNAL BUS SECTION NUMBER 2 LOCATED OVER THE CONTROL ROOM MEZZANINE IN THE SIGNAL POWER CONDITIONING ROOM. BUS IS A HEAVY COPPER BAR APPROXIMATELY 1/2" BY 4" WHICH CONDUCTS POWER THROUGHOUT THE POWER PLANT. BUS ARE PROTECTED BY A BRICK AND SOAPSTONE HOUSING. OPENINGS FOR INSPECTION AND ACCESS WOULD NORMALLY BE PROTECTED BY GLASS DOORS. THE BUS WOULD BE SUPPORTED ON INSULATORS WITHIN THE BRICK CHAMBER. BUS WAS REMOVED AND SALVAGED WHEN THE STATION WAS ABANDONED. THE OBJECT IN THE TOP CENTER OF THE PHOTOGRAPH IS A POTENTIAL TRANSFORMER USED TO REDUCE BUS POTENTIAL OF 2200 VOLTS TO LOW VOLTAGES SAFE FOR USE IN CONTROL ROOM CIRCUITRY. POTENTIAL TRANSFORMERS ARE PRECISION DEVICES WHICH PRODUCE AN ACCURATE LOW VOLTAGE ANALOG OF THE HIGH VOLTAGE ON THE BUS. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Degree of target utilization influences the location of movement endpoint distributions.

PubMed

Slifkin, Andrew B; Eder, Jeffrey R

2017-03-01

According to dominant theories of motor control, speed and accuracy are optimized when, on the average, movement endpoints are located at the target center and when the variability of the movement endpoint distributions is matched to the width of the target (viz., Meyer, Abrams, Kornblum, Wright, & Smith, 1988). The current study tested those predictions. According to the speed-accuracy trade-off, expanding the range of variability to the amount permitted by the limits of the target boundaries allows for maximization of movement speed while centering the distribution on the target center prevents movement errors that would have occurred had the distribution been off center. Here, participants (N=20) were required to generate 100 consecutive targeted hand movements under each of 15 unique conditions: There were three movement amplitude requirements (80, 160, 320mm) and within each there were five target widths (5, 10, 20, 40, 80mm). According to the results, it was only at the smaller target widths (5, 10mm) that movement endpoint distributions were centered on the target center and the range of movement endpoint variability matched the range specified by the target boundaries. As target width increased (20, 40, 80mm), participants increasingly undershot the target center and the range of movement endpoint variability increasingly underestimated the variability permitted by the target region. The degree of target center undershooting was strongly predicted by the difference between the size of the target and the amount of movement endpoint variability, i.e., the amount of unused space in the target. The results suggest that participants have precise knowledge of their variability relative to that permitted by the target, and they use that knowledge to systematically reduce the travel distance to targets. The reduction in travel distance across the larger target widths might have resulted in greater cost savings than those associated with increases in speed. Copyright © 2017. Published by Elsevier B.V.

Remotely Delivered Exercise-Based Cardiac Rehabilitation: Design and Content Development of a Novel mHealth Platform.

PubMed

Rawstorn, Jonathan C; Gant, Nicholas; Meads, Andrew; Warren, Ian; Maddison, Ralph

2016-06-24

Participation in traditional center-based cardiac rehabilitation exercise programs (exCR) is limited by accessibility barriers. Mobile health (mHealth) technologies can overcome these barriers while preserving critical attributes of center-based exCR monitoring and coaching, but these opportunities have not yet been capitalized on. We aimed to design and develop an evidence- and theory-based mHealth platform for remote delivery of exCR to any geographical location. An iterative process was used to design and develop an evidence- and theory-based mHealth platform (REMOTE-CR) that provides real-time remote exercise monitoring and coaching, behavior change education, and social support. The REMOTE-CR platform comprises a commercially available smartphone and wearable sensor, custom smartphone and Web-based applications (apps), and a custom middleware. The platform allows exCR specialists to monitor patients' exercise and provide individualized coaching in real-time, from almost any location, and provide behavior change education and social support. Intervention content incorporates Social Cognitive Theory, Self-determination Theory, and a taxonomy of behavior change techniques. Exercise components are based on guidelines for clinical exercise prescription. The REMOTE-CR platform extends the capabilities of previous telehealth exCR platforms and narrows the gap between existing center- and home-based exCR services. REMOTE-CR can complement center-based exCR by providing an alternative option for patients whose needs are not being met. Remotely monitored exCR may be more cost-effective than establishing additional center-based programs. The effectiveness and acceptability of REMOTE-CR are now being evaluated in a noninferiority randomized controlled trial.

Planning Paths Through Singularities in the Center of Mass Space

NASA Technical Reports Server (NTRS)

Doggett, William R.; Messner, William C.; Juang, Jer-Nan

1998-01-01

The center of mass space is a convenient space for planning motions that minimize reaction forces at the robot's base or optimize the stability of a mechanism. A unique problem associated with path planning in the center of mass space is the potential existence of multiple center of mass images for a single Cartesian obstacle, since a single center of mass location can correspond to multiple robot joint configurations. The existence of multiple images results in a need to either maintain multiple center of mass obstacle maps or to update obstacle locations when the robot passes through a singularity, such as when it moves from an elbow-up to an elbow-down configuration. To illustrate the concepts presented in this paper, a path is planned for an example task requiring motion through multiple center of mass space maps. The object of the path planning algorithm is to locate the bang- bang acceleration profile that minimizes the robot's base reactions in the presence of a single Cartesian obstacle. To simplify the presentation, only non-redundant robots are considered and joint non-linearities are neglected.

KSC-04PD-0937

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000- foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid- point of the runway is where the new control tower is located.

KSC-04PD-0936

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo shows the runway at the KSC Shuttle Landing Facility extending left to upper right. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower center. In the upper right is a grassy area where the new control tower is located.

KSC-04PD-0938

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000- foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid- point of the runway is where the new control tower is located.

KSC-04pd0936

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo shows the runway at the KSC Shuttle Landing Facility extending left to upper right. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower center. In the upper right is a grassy area where the new control tower is located.

KSC-04pd0938

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid-point of the runway is where the new control tower is located.

KSC-04pd0937

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid-point of the runway is where the new control tower is located.

Geological and geochemical aspects of uranium deposits: a selected, annotated bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, J.M.; Brock, M.L.; Garland, P.A.

1978-06-01

A compilation of 490 references is presented which is the second in a series compiled from the National Uranium Resource Evaluation (NURE) Bibliographic Data Base. This data base is one of six created by the Ecological Sciences Information Center, Oak Ridge National Laboratory, for the Grand Junction Office of the Department of Energy. Major emphasis for this volume has been placed on uranium geology, encompassing deposition, genesis of ore deposits, and ore controls; and prospecting techniques, including geochemistry and aerial reconnaissance. The following indexes are provided to aid the user in locating references of interest: author, geographic location, quadrangel name,more » geoformational feature, taxonomic name, and keyword.« less

Foraging swarms as Nash equilibria of dynamic games.

PubMed

Özgüler, Arif Bülent; Yildiz, Aykut

2014-06-01

The question of whether foraging swarms can form as a result of a noncooperative game played by individuals is shown here to have an affirmative answer. A dynamic game played by N agents in 1-D motion is introduced and models, for instance, a foraging ant colony. Each agent controls its velocity to minimize its total work done in a finite time interval. The game is shown to have a unique Nash equilibrium under two different foraging location specifications, and both equilibria display many features of a foraging swarm behavior observed in biological swarms. Explicit expressions are derived for pairwise distances between individuals of the swarm, swarm size, and swarm center location during foraging.

Supersonic aerodynamic characteristics of a proposed Assured Crew Return Capability (ACRC) lifting-body configuration

NASA Technical Reports Server (NTRS)

Ware, George M.

1989-01-01

An investigation was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers from 1.6 to 4.5. The model had a low-aspect-ratio body with a flat undersurface. A center fin and two outboard fins were mounted on the aft portion of the upper body. The outboard fins were rolled outboard 40 deg from the vertical. Elevon surfaces made up the trailing edges of the outboard fins, and body flaps were located on the upper and lower aft fuselage. The center fin pivoted about its midchord for yaw control. The model was longitudinally stable about the design center-of-gravity position at 54 percent of the body length. The configuration with undeflected longitudinal controls trimmed near 0 deg angle of attack at Mach numbers from 1.6 to 3.0 where lift and lift-drag ratio were negative. Longitudinal trim was near the maximum lift-drag ratio (1.4) at Mach 4.5. The model was directionally stable over Mach number range except at angles of attack around 4 deg at M = 2.5. Pitch control deflection of more than -10 deg with either elevons or body flaps is needed to trim the model to angles of attack at which lift becomes positive. With increased control deflection, the lifting-body configuration should perform the assured crew return mission through the supersonic speed range.

From Apollo to Cognac

NASA Technical Reports Server (NTRS)

1980-01-01

Shell Oil Company started oil and gas production from a new offshore platform called Cognac located in the Gulf of Mexico. It is the world's tallest oil platform, slightly taller than the Empire State Building. The highly complex job of installing Cognac's support "jacket" under water more than a thousand feet deep was directed from a barge-based control center. To enable crews to practice in advance difficult tasks never before accomplished, Honeywell, adapting NASA's Apollo technology, developed a system for simulating the various underwater operations. In training sessions, displays and controls reacted exactly as they would in real operation.

Method and apparatus for strip casting

DOEpatents

Follstaedt, D.W.; Powell, J.C.; Sussman, R.C.; Williams, R.S.

1991-11-12

Casting nozzles will provide improved flow conditions with the parameters controlled according to the present invention. The gap relationships between the nozzle slot and exit orifice must be controlled in combination with converging exit passageway to provide a smooth flow without shearing and turbulence in the stream. The nozzle lips are also rounded to improve flow and increase refractory life of the lips of the nozzle. The tundish walls are tapered to provide improve flow for supplying the melt to the nozzle. The nozzle is located about 45[degree] below top dead center for optimum conditions. 2 figures.

PHOTO DATE: 08-10-15.LOCATION: Bldg. 30 - FCR-1 (30M/231).SUBJECT: Expedition 44, Kjell Lindgren.Kimiya Yui AND SCOTT KELLY TASTING SPACE LETTUCE EXPERIMENT.PHOTOGRAPHER: BILL STAFFORD

NASA Image and Video Library

2015-08-10

JSC2015E076004 (08/10/2015) --- Flight controllers in the International Space Station Mission Control at the Johnson Space Center monitor systems aboard the orbiting laboratory during a number of dynamic events for Expedition 44. Screens in the front of the room show the camera views from two spacewalking Russian cosmonauts while NASA astronaut Kjell Lindgren is seen harvesting lettuce from the Veggie experiment that would become the first food grown in space to be eaten. NASA Photographer Bill Stafford.

Aerial view of the Shuttle Landing Facility

NASA Technical Reports Server (NTRS)

1998-01-01

From the air over KSC can be seen the Shuttle Landing Facility. Orbiter landings at the Kennedy Space Center are made on one of the largest runways in the world. The runway is located 3.2 km (2 miles) northwest of the Vehicle Assembly Building and is 4,572 meters (15,000ft) long and 91.4 meters (300ft) wide -- about as wide as the length of a football field. It has 305 meters (1000ft) of paved overruns at each end and the paving thickness is 40.6cm (15 inches) at the center. At left in the photo is the Aircraft Ground Equipment Shed; in the center is the Landing Aids Control Building (LACB) which supports landing operations and houses operations personnel. Located at the northeast corner of the parking apron is the Mate/Demate device (MDD) used to raise and lower the orbiter from its 747 carrier aircraft during ferry operations. The open-truss steel structure is equipped with hoists, adapters and movable platforms for access to certain orbiter components and equipment. It also is equipped with lightning protection devices. The MDD is 45.7 meters (150ft) long, 28.3 meters (93ft) wide and 32 meters (105ft) high. On the landing area in front of the SLF is a T-38 jet airplane.

A Study of Flood Evacuation Center Using GIS and Remote Sensing Technique

NASA Astrophysics Data System (ADS)

Mustaffa, A. A.; Rosli, M. F.; Abustan, M. S.; Adib, R.; Rosli, M. I.; Masiri, K.; Saifullizan, B.

2016-07-01

This research demonstrated the use of Remote Sensing technique and GIS to determine the suitability of an evacuation center. This study was conducted in Batu Pahat areas that always hit by a series of flood. The data of Digital Elevation Model (DEM) was obtained by ASTER database that has been used to delineate extract contour line and elevation. Landsat 8 image was used for classification purposes such as land use map. Remote Sensing incorporate with GIS techniques was used to determined the suitability location of the evacuation center from contour map of flood affected areas in Batu Pahat. GIS will calculate the elevation of the area and information about the country of the area, the road access and percentage of the affected area. The flood affected area map may provide the suitability of the flood evacuation center during the several levels of flood. The suitability of evacuation centers can be determined based on several criteria and the existing data of the evacuation center will be analysed. From the analysis among 16 evacuation center listed, there are only 8 evacuation center suitable for the usage during emergency situation. The suitability analysis was based on the location and the road access of the evacuation center toward the flood affected area. There are 10 new locations with suitable criteria of evacuation center proposed on the study area to facilitate the process of rescue and evacuating flood victims to much safer and suitable locations. The results of this study will help in decision making processes and indirectly will help organization such as fire-fighter and the Department of Social Welfare in their work. Thus, this study can contribute more towards the society.

Marine Corps Close Air Support Development from Guadalcanal to Okinawa

DTIC Science & Technology

2011-03-05

air support (CAS) of troops in contact with the enemy came of age . While the capability clearly had potential, issues of coordination, accurate...including the first use of an Air Support Control Unit ( ASCU ), predecessor of the Fire S.upport Coordination Center.71 The Command Ship initially...which artillery had to cease fire for low- level napalm air strikes. When two or more battalions fired on the same location, the ASCU used maximum

Humanoid robot Lola: design and walking control.

PubMed

Buschmann, Thomas; Lohmeier, Sebastian; Ulbrich, Heinz

2009-01-01

In this paper we present the humanoid robot LOLA, its mechatronic hardware design, simulation and real-time walking control. The goal of the LOLA-project is to build a machine capable of stable, autonomous, fast and human-like walking. LOLA is characterized by a redundant kinematic configuration with 7-DoF legs, an extremely lightweight design, joint actuators with brushless motors and an electronics architecture using decentralized joint control. Special emphasis was put on an improved mass distribution of the legs to achieve good dynamic performance. Trajectory generation and control aim at faster, more flexible and robust walking. Center of mass trajectories are calculated in real-time from footstep locations using quadratic programming and spline collocation methods. Stabilizing control uses hybrid position/force control in task space with an inner joint position control loop. Inertial stabilization is achieved by modifying the contact force trajectories.

Clinical islet transplantation experience of the University of California Islet Transplant Consortium.

PubMed

Brunicardi, F C; Atiya, A; Stock, P; Kenmochi, T; Une, S; Benhamou, P Y; Watt, P C; Miyamato, M; Wantanabe, Y; Nomura, Y

1995-12-01

The University of California Islet Transplant Consortium was formed to evaluate the feasibility of performing clinical islet transplantation at different transplant centers by using a single centralized islet isolation laboratory. From July 1992 through February 1995 seven adult islet transplantations were performed, six allografts and one autograft. Once procured, human pancreata were brought to the UCLA-VA Islet Core Laboratory for islet isolation and purification, which were then transported to different centers for transplantation. Patients 1 through 3 received their transplants in Los Angeles, patient 4 received her islet transplant in Torrance, and patients 5 through 7 received their transplants in San Francisco. Although none of these patients achieved insulin independence, four of seven had functioning grafts longer than 6 months as indicated by circulating C-peptide level greater than 0.7 ng/ml. Furthermore, improved glucose control as shown by a decreased insulin requirement was seen in 57% (four of seven patients) of these patients. The ability to isolate islets at a single laboratory and transport them long distances to different centers was shown in patients 4 through 7. Islet transplantation can be performed with improvements in blood glucose control, and islets can be isolated at a centralized location and successfully transported to different centers for transplantation.

Sensors Locate Radio Interference

NASA Technical Reports Server (NTRS)

2009-01-01

After receiving a NASA Small Business Innovation Research (SBIR) contract from Kennedy Space Center, Soneticom Inc., based in West Melbourne, Florida, created algorithms for time difference of arrival and radio interferometry, which it used in its Lynx Location System (LLS) to locate electromagnetic interference that can disrupt radio communications. Soneticom is collaborating with the Federal Aviation Administration (FAA) to install and test the LLS at its field test center in New Jersey in preparation for deploying the LLS at commercial airports. The software collects data from each sensor in order to compute the location of the interfering emitter.

The Northern California Earthquake Management System: A Unified System From Realtime Monitoring to Data Distribution

NASA Astrophysics Data System (ADS)

Neuhauser, D.; Dietz, L.; Lombard, P.; Klein, F.; Zuzlewski, S.; Kohler, W.; Hellweg, M.; Luetgert, J.; Oppenheimer, D.; Romanowicz, B.

2006-12-01

The longstanding cooperation between the USGS Menlo Park and UC Berkeley's Seismological Laboratory for monitoring earthquakes and providing data to the research community is achieving a new level of integration. While station support and data collection for each network (NC, BK, BP) remain the responsibilities of the host institution, picks, codas and amplitudes will be produced and shared between the data centers continuously. Thus, realtime earthquake processing from triggering and locating through magnitude and moment tensor calculation and Shakemap production will take place independently at both locations, improving the robustness of event reporting in the Northern California Earthquake Management Center. Parametric data will also be exchanged with the Southern California Earthquake Management System to allow statewide earthquake detection and processing for further redundancy within the California Integrated Seismic Network (CISN). The database plays an integral part in this system, providing the coordination for event processing as well as the repository for event, instrument (metadata) and waveform information. The same master database serves both realtime processing, data quality control and archival, and the data center which provides waveforms and earthquake data to users in the research community. Continuous waveforms from all BK, BP, and NC stations, event waveform gathers, and event information automatically become available at the Northern California Earthquake Data Center (NCEDC). Currently, the NCEDC is collecting and makes available over 4 TByes of data per year from the NCEMC stations and other seismic networks, as well as from GPS and and other geophysical instrumentation.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2017-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2018-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

Italy INAF Analysis Center Report

NASA Technical Reports Server (NTRS)

Negusini, M.; Sarti, P.

2013-01-01

This report summarizes the activity of the Italian INAF VLBI Analysis Center. Our Analysis Center is located in Bologna, Italy and belongs to the Institute of Radioastronomy, which is part of the National Institute of Astrophysics. IRA runs the observatories of Medicina and Noto, where two 32-m VLBI AZ-EL telescopes are situated. This report contains the AC's VLBI data analysis activities and shortly outlines the investigations into the co-locations of space geodetic instruments.

Distributing Data to Hand-Held Devices in a Wireless Network

NASA Technical Reports Server (NTRS)

Hodges, Mark; Simmons, Layne

2008-01-01

ADROIT is a developmental computer program for real-time distribution of complex data streams for display on Web-enabled, portable terminals held by members of an operational team of a spacecraft-command-and-control center who may be located away from the center. Examples of such terminals include personal data assistants, laptop computers, and cellular telephones. ADROIT would make it unnecessary to equip each terminal with platform- specific software for access to the data streams or with software that implements the information-sharing protocol used to deliver telemetry data to clients in the center. ADROIT is a combination of middleware plus software specific to the center. (Middleware enables one application program to communicate with another by performing such functions as conversion, translation, consolidation, and/or integration.) ADROIT translates a data stream (voice, video, or alphanumerical data) from the center into Extensible Markup Language, effectuates a subscription process to determine who gets what data when, and presents the data to each user in real time. Thus, ADROIT is expected to enable distribution of operations and to reduce the cost of operations by reducing the number of persons required to be in the center.

Public Address Set AN/UIQ-10 (XLW-1)

DTIC Science & Technology

1972-01-01

case. /,320 Hz No visible indication. Major Horizontal Broadband Resonance Resonance center located 300 to 500 peak at on case over relay bracket. ’ 375 ... Hz No visible indication. Minor Horizontal Broadband Resonance Resonance center located 150 to 190 peak at case over relay bracket. � Hz Slight

20 CFR 670.200 - Who decides where Job Corps centers will be located?

Code of Federal Regulations, 2010 CFR

2010-04-01

... for making decisions concerning the establishment, relocation, expansion, or closing of contract... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Who decides where Job Corps centers will be located? 670.200 Section 670.200 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF...

The effect of number and distribution of unsplinted maxillary implants on the load transfer in implant-retained maxillary overdentures: an in vitro study.

PubMed

Damghani, Sahar; Masri, Radi; Driscoll, Carl F; Romberg, Elaine

2012-06-01

There is little information as to how the number and distribution of implants affect the amount of load transmitted to the palate in implant-retained maxillary overdentures. The purpose of this study was to evaluate the effect of the number and distribution of dental implants on the load transmitted to the palate. Eight implant analogues were placed in a replica of an average sized edentulous maxilla corresponding to the position of canines, first and second premolars, and first molars. The anteroposterior distance between the centers of implants in each quadrant was 8 mm. Fifteen denture bases were fabricated to fit the edentulous maxilla analogue. The denture bases were attached to the oral analogue using 6 different configurations of attachments (6 groups): Either no Locator attachments were used (control group), or the 2 most anterior attachments were attached, or 4 implants were engaged with a distance of 8, 16, or 24 mm between the centers of implants on left and right side, and finally, when all 8 attachments were activated. A force-measuring sensor was used to measure the force transmitted to the palate when a static force of 245 N was applied on the occlusal rims of the denture bases. Data (Newtons) were analyzed using 1-way ANOVA and Tukey's HSD test α=.05). The mean (SD) amount of force measured on the palate when the overdentures were supported by 4 Locator attachments; [49.84 (26.52) at 8 mm spacing], [24.42 (15.05) at 16 mm spacing], [35.66 (22.94) at 24 mm spacing] was significantly lower than when no attachments [90.98 (20.20), control], or when 2 Locator attachments were used [76.07 (27.63)] (P<.001). When the overdentures were supported by 8 Locator attachments, the force measured on the palate [20.67(16.06) N] was significantly lower than that for the control group (P<.001), overdentures supported by 2 Locator attachments (P<.001), and overdentures supported by 4 Locator attachments when the distance between the anterior and posterior implants was 8 mm P=.006). The distribution of implants had a significant effect on the force measured on the palate of the oral analogue in overdentures retained by Locator attachments. When the distance between the 4 implants was 16 or more mm, the load was not significantly lower than the 8 implant design, suggesting that the palate of a 4 implant-retained overdenture with a distance of 16 mm or more, does not contribute significantly to the load transfer to underlying hard palate in the in vitro analogue evaluated. Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

KSC-04PD-0279

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. U.S. Senator Bill Nelson (center) and NASA Administrator Sean OKeefe are deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson at left is Congressman Tom Feeney. The research park is being proposed as the location for NASAs new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASAs payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

Mitigation of the consequence of seismically induced damage on a utility water network by means of next generation SCADA

NASA Astrophysics Data System (ADS)

Robertson, Jamie; Shinozuka, Masanobu; Wu, Felix

2011-04-01

When a lifeline system such as a water delivery network is damaged due to a severe earthquake, it is critical to identify its location and extent of the damage in real time in order to minimize the potentially disastrous consequence such damage could otherwise entail. This paper demonstrates how the degree of such minimization can be estimated qualitatively by using the water delivery system of Irvine Water Ranch District (IRWD) as testbed, when it is subjected to magnitude 6.6 San Joaquin Hills Earthquake. In this demonstration, we consider two cases when the IRWD system is equipped or not equipped with a next generation SCADA which consists of a network of MEMS acceleration sensors densely populated and optimally located. These sensors are capable of identifying the location and extent of the damage as well as transmitting the data to the SCADA center for monitoring and control.

Method and apparatus for deflection measurements using eddy current effects

NASA Astrophysics Data System (ADS)

Chern, Engmin J.

1993-05-01

A method and apparatus for inserting and moving a sensing assembly with a mechanical positioning assembly to a desired remote location of a surface of a specimen under test and measuring angle and/or deflection by sensing the change in the impedance of at least one sensor coil located in a base plate which has a rotatable conductive plate pivotally mounted thereon so as to uncover the sensor coil(s) whose impedance changes as a function of deflection away from the center line of the base plate in response to the movement of the rotator plate when contacting the surface of the specimen under test is presented. The apparatus includes the combination of a system controller, a sensing assembly, an eddy current impedance measuring apparatus, and a mechanical positioning assembly driven by the impedance measuring apparatus to position the sensing assembly at a desired location of the specimen.

Method and apparatus for deflection measurements using eddy current effects

NASA Technical Reports Server (NTRS)

Chern, Engmin J. (Inventor)

1993-01-01

A method and apparatus for inserting and moving a sensing assembly with a mechanical positioning assembly to a desired remote location of a surface of a specimen under test and measuring angle and/or deflection by sensing the change in the impedance of at least one sensor coil located in a base plate which has a rotatable conductive plate pivotally mounted thereon so as to uncover the sensor coil(s) whose impedance changes as a function of deflection away from the center line of the base plate in response to the movement of the rotator plate when contacting the surface of the specimen under test is presented. The apparatus includes the combination of a system controller, a sensing assembly, an eddy current impedance measuring apparatus, and a mechanical positioning assembly driven by the impedance measuring apparatus to position the sensing assembly at a desired location of the specimen.

Study on Data Clustering and Intelligent Decision Algorithm of Indoor Localization

NASA Astrophysics Data System (ADS)

Liu, Zexi

2018-01-01

Indoor positioning technology enables the human beings to have the ability of positional perception in architectural space, and there is a shortage of single network coverage and the problem of location data redundancy. So this article puts forward the indoor positioning data clustering algorithm and intelligent decision-making research, design the basic ideas of multi-source indoor positioning technology, analyzes the fingerprint localization algorithm based on distance measurement, position and orientation of inertial device integration. By optimizing the clustering processing of massive indoor location data, the data normalization pretreatment, multi-dimensional controllable clustering center and multi-factor clustering are realized, and the redundancy of locating data is reduced. In addition, the path is proposed based on neural network inference and decision, design the sparse data input layer, the dynamic feedback hidden layer and output layer, low dimensional results improve the intelligent navigation path planning.

Teaching Health Center Graduate Medical Education Locations Predominantly Located in Federally Designated Underserved Areas.

PubMed

Barclift, Songhai C; Brown, Elizabeth J; Finnegan, Sean C; Cohen, Elena R; Klink, Kathleen

2016-05-01

Background The Teaching Health Center Graduate Medical Education (THCGME) program is an Affordable Care Act funding initiative designed to expand primary care residency training in community-based ambulatory settings. Statute suggests, but does not require, training in underserved settings. Residents who train in underserved settings are more likely to go on to practice in similar settings, and graduates more often than not practice near where they have trained. Objective The objective of this study was to describe and quantify federally designated clinical continuity training sites of the THCGME program. Methods Geographic locations of the training sites were collected and characterized as Health Professional Shortage Area, Medically Underserved Area, Population, or rural areas, and were compared with the distribution of Centers for Medicare and Medicaid Services (CMS)-funded training positions. Results More than half of the teaching health centers (57%) are located in states that are in the 4 quintiles with the lowest CMS-funded resident-to-population ratio. Of the 109 training sites identified, more than 70% are located in federally designated high-need areas. Conclusions The THCGME program is a model that funds residency training in community-based ambulatory settings. Statute suggests, but does not explicitly require, that training take place in underserved settings. Because the majority of the 109 clinical training sites of the 60 funded programs in 2014-2015 are located in federally designated underserved locations, the THCGME program deserves further study as a model to improve primary care distribution into high-need communities.

The dynamics and control of large flexible space structures. Part A: Discrete model and modal control

NASA Technical Reports Server (NTRS)

Bainum, P. M.; Sellappan, R.

1978-01-01

Attitude control techniques for the pointing and stabilization of very large, inherently flexible spacecraft systems were investigated. The attitude dynamics and control of a long, homogeneous flexible beam whose center of mass is assumed to follow a circular orbit was analyzed. First order effects of gravity gradient were included. A mathematical model which describes the system rotations and deflections within the orbital plane was developed by treating the beam as a number of discretized mass particles connected by massless, elastic structural elements. The uncontrolled dynamics of the system are simulated and, in addition, the effects of the control devices were considered. The concept of distributed modal control, which provides a means for controlling a system mode independently of all other modes, was examined. The effect of varying the number of modes in the model as well as the number and location of the control devices were also considered.

Positional priming of visual pop-out search is supported by multiple spatial reference frames

PubMed Central

Gokce, Ahu; Müller, Hermann J.; Geyer, Thomas

2015-01-01

The present study investigates the representations(s) underlying positional priming of visual ‘pop-out’ search (Maljkovic and Nakayama, 1996). Three search items (one target and two distractors) were presented at different locations, in invariant (Experiment 1) or random (Experiment 2) cross-trial sequences. By these manipulations it was possible to disentangle retinotopic, spatiotopic, and object-centered priming representations. Two forms of priming were tested: target location facilitation (i.e., faster reaction times – RTs– when the trial n target is presented at a trial n-1 target relative to n-1 blank location) and distractor location inhibition (i.e., slower RTs for n targets presented at n-1 distractor compared to n-1 blank locations). It was found that target locations were coded in positional short-term memory with reference to both spatiotopic and object-centered representations (Experiment 1 vs. 2). In contrast, distractor locations were maintained in an object-centered reference frame (Experiments 1 and 2). We put forward the idea that the uncertainty induced by the experiment manipulation (predictable versus random cross-trial item displacements) modulates the transition from object- to space-based representations in cross-trial memory for target positions. PMID:26136718

Alternative Fuels Data Center: Natural Gas Fueling Station Locations

Science.gov Websites

or ZIP code or along a route in the United States. Loading alternative fueling station locator Fleet Rightsizing System Efficiency Locate Stations Search by Location Map a Route Laws & Incentives

42 CFR 482.70 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... geographic area specified by CMS. Heart-Lung transplant center means a transplant center that is located in a hospital with an existing Medicare-approved heart transplant center and an existing Medicare-approved lung center that performs combined heart-lung transplants. Intestine transplant center means a Medicare...

42 CFR 482.70 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... geographic area specified by CMS. Heart-Lung transplant center means a transplant center that is located in a hospital with an existing Medicare-approved heart transplant center and an existing Medicare-approved lung center that performs combined heart-lung transplants. Intestine transplant center means a Medicare...

42 CFR 482.70 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... geographic area specified by CMS. Heart-Lung transplant center means a transplant center that is located in a hospital with an existing Medicare-approved heart transplant center and an existing Medicare-approved lung center that performs combined heart-lung transplants. Intestine transplant center means a Medicare...

42 CFR 482.70 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... geographic area specified by CMS. Heart-Lung transplant center means a transplant center that is located in a hospital with an existing Medicare-approved heart transplant center and an existing Medicare-approved lung center that performs combined heart-lung transplants. Intestine transplant center means a Medicare...

Artificial Intelligence (AI) Center of Excellence at the University of Pennsylvania

DTIC Science & Technology

1995-07-01

that controls impact forces. Robust Location Estimation for MLR and Non-MLR Distributions (Dissertation Proposal) Gerda L. Kamberova MS-CIS-92-28...Bayesian Approach To Computer Vision Problems Gerda L. Kamberova MS-CIS-92-29 GRASP LAB 310 The object of our study is the Bayesian approach in...Estimation for MLR and Non-MLR Distributions (Dissertation) Gerda L. Kamberova MS-CIS-92-93 GRASP LAB 340 We study the problem of estimating an unknown

Solar-energy-system performance evaluation, October 1980-August 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wetzel, P.E.

The solar site is an Animal Quarantine Center in Upton, New York, using 2484 ft/sup 2/ of flat-plate collectors and 5300 gallons of solar hot water storage located outside and above ground. The system was designed to provide 20% of the annual heating load and 100% of the annual domestic hot water load. The solar system actually provided 5% of the total system load. Many control and mechanical malfunctions contributed to the poor performance. (MHR)

STS-26 Commander Hauck in fixed based (FB) shuttle mission simulator (SMS)

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Commander Frederick H. Hauck, wearing comunications kit assembly headset, checks control panel data while seated in the commanders seat on forward flight deck. A flight data file (FDF) notebook rests on his lap. A portable computer (laptop) is positioned on the center console. The STS-26 crew is training in the fixed base (FB) shuttle mission simulator (SMS) located in JSC Mission Simulation and Training Facility Bldg 5.

Aerodynamics and Hovering Control of LTA Vehicles

DTIC Science & Technology

1977-05-01

not at all the usual terminology for Magnus Force which is usually thought of as arising from viscous effects when cylinder or sphere is rotating and...Number for Circular Cylinders 9 Ratio of the Drag Coefficient of a Circular Cylinder 29 of Finite Length to That of a Cylincer of Infinite Length as...Application of Non-Linear Drag 82 30 Directional Stability Derivative 83 31 Center of Lateral Pressure Location 84 32 Dihedral Effect Derivative 85 v Figures

Houston, Galveston Bay, Texas, USA

NASA Image and Video Library

1985-10-07

Long regarded as one of the best photo of Houston, Texas (29.5N, 95.0W), this view from space shows the entire greater Houston/Galveston region in remarkable detail and clarity. The dark north/south line in the water between Houston and Galveston is the Houston Ship Channel. NASA's Johnson Space Center and Mission Control is located on the north shore of Clear Lake west of the channel. The extensive road and highway network can be seen in great detail.

26. Port side of engine room looking forward from aft ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Port side of engine room looking forward from aft bulkhead. This area contains mostly electrical equipment. Two single-cylinder steam-driven dynamos are located near the engine bed, one at right foreground, the other in background. At left in image are a motor-generator set installed to convert DC current (from dynamos) to AC current. Edge-on view of control panel appears near center of image. - Ferry TICONDEROGA, Route 7, Shelburne, Chittenden County, VT

Effects of visual cues of object density on perception and anticipatory control of dexterous manipulation.

PubMed

Crajé, Céline; Santello, Marco; Gordon, Andrew M

2013-01-01

Anticipatory force planning during grasping is based on visual cues about the object's physical properties and sensorimotor memories of previous actions with grasped objects. Vision can be used to estimate object mass based on the object size to identify and recall sensorimotor memories of previously manipulated objects. It is not known whether subjects can use density cues to identify the object's center of mass (CM) and create compensatory moments in an anticipatory fashion during initial object lifts to prevent tilt. We asked subjects (n = 8) to estimate CM location of visually symmetric objects of uniform densities (plastic or brass, symmetric CM) and non-uniform densities (mixture of plastic and brass, asymmetric CM). We then asked whether subjects can use density cues to scale fingertip forces when lifting the visually symmetric objects of uniform and non-uniform densities. Subjects were able to accurately estimate an object's center of mass based on visual density cues. When the mass distribution was uniform, subjects could scale their fingertip forces in an anticipatory fashion based on the estimation. However, despite their ability to explicitly estimate CM location when object density was non-uniform, subjects were unable to scale their fingertip forces to create a compensatory moment and prevent tilt on initial lifts. Hefting object parts in the hand before the experiment did not affect this ability. This suggests a dichotomy between the ability to accurately identify the object's CM location for objects with non-uniform density cues and the ability to utilize this information to correctly scale their fingertip forces. These results are discussed in the context of possible neural mechanisms underlying sensorimotor integration linking visual cues and anticipatory control of grasping.

Longitudinal Stability and Control Characteristics from a Flight Investigation of a Cruciform Canard Missile Configuration Having an Exposed Wing-canard Area Ratio of 16:1

NASA Technical Reports Server (NTRS)

Moul, Martin T; Wineman, Andrew R

1952-01-01

A flight investigation has been made to determine the longitudinal stability and control characteristics of a 60 0 delta-wing-canard missile configuration with an exposed wing-canard area ratio of 16:1. The results presented include the longitudinal stability derivatives, control effectiveness, and drag characteristics for a Mach number range of 0.75 to 1.80 and are compared with the results of a similar configuration having larger 6ontrols. Stability characteristics are also presented from the flights of an interdigitated canard configuration at a Mach number of 2.08 and a wing-body configuration at Mach numbers of 1.25 to 1.45. The stability derivatives varied gradually with Mach number with the exception of the damping-in-pitch derivative. Aerodynamic damping in pitch decreased to a minimum at a Mach number of 1.0 3, then increased to a peak value at a Mach number of 1.26 followed by a gradual decrease at higher Mach numbers. The aerodynamic-center location of the in-line canard configuration shifted rearward 13 percent of the mean aerodynamic chord at transonic speeds. The pitching-moment curve slope was 25 percent greater for the model having no canards than for the in-line configuration. No large effects of interdigitation were noted in the stability derivatives. Pitching effectiveness of the in-line configuration was maintained throughout the Mach number range. A comparison of the stability and control characteristics of two canard configurations having different area controls showed that decreasing the control area 44 percent decreased the pitching effectiveness proportionally, shifted the aerodynamic-center location rearward 9 to 14 percent of the mean aerodynamic chord, and reduced the total hinge moments required for 10 trimmed flight about 50 percent at transonic speeds.

Investigation of Control System and Display Variations on Spacecraft Handling Qualities for Docking with Stationary and Rotating Targets

NASA Technical Reports Server (NTRS)

Jackson, E. Bruce; Goodrich, Kenneth H.; Bailey, Randall E.; Barnes, James R.; Ragsdale, William A.; Neuhaus, Jason R.

2010-01-01

This paper documents the investigation into the manual docking of a preliminary version of the Crew Exploration Vehicle with stationary and rotating targets in Low Earth Orbit. The investigation was conducted at NASA Langley Research Center in the summer of 2008 in a repurposed fixed-base transport aircraft cockpit and involved nine evaluation astronauts and research pilots. The investigation quantified the benefits of a feed-forward reaction control system thruster mixing scheme to reduce translation-into-rotation coupling, despite unmodeled variations in individual thruster force levels and off-axis center of mass locations up to 12 inches. A reduced rate dead-band in the phase-plane attitude controller also showed some promise. Candidate predictive symbology overlaid on a docking ring centerline camera image did not improve handling qualities, but an innovative attitude status indicator symbol was beneficial. The investigation also showed high workload and handling quality problems when manual dockings were performed with a rotating target. These concerns indicate achieving satisfactory handling quality ratings with a vehicle configuration similar to the nominal Crew Exploration Vehicle may require additional automation.

Development of quality control and instrumentation performance metrics for diffuse optical spectroscopic imaging instruments in the multi-center clinical environment

NASA Astrophysics Data System (ADS)

Keene, Samuel T.; Cerussi, Albert E.; Warren, Robert V.; Hill, Brian; Roblyer, Darren; Leproux, AnaÑ--s.; Durkin, Amanda F.; O'Sullivan, Thomas D.; Haghany, Hosain; Mantulin, William W.; Tromberg, Bruce J.

2013-03-01

Instrument equivalence and quality control are critical elements of multi-center clinical trials. We currently have five identical Diffuse Optical Spectroscopic Imaging (DOSI) instruments enrolled in the American College of Radiology Imaging Network (ACRIN, #6691) trial located at five academic clinical research sites in the US. The goal of the study is to predict the response of breast tumors to neoadjuvant chemotherapy in 60 patients. In order to reliably compare DOSI measurements across different instruments, operators and sites, we must be confident that the data quality is comparable. We require objective and reliable methods for identifying, correcting, and rejecting low quality data. To achieve this goal, we developed and tested an automated quality control algorithm that rejects data points below the instrument noise floor, improves tissue optical property recovery, and outputs a detailed data quality report. Using a new protocol for obtaining dark-noise data, we applied the algorithm to ACRIN patient data and successfully improved the quality of recovered physiological data in some cases.

Remotely Delivered Exercise-Based Cardiac Rehabilitation: Design and Content Development of a Novel mHealth Platform

PubMed Central

Gant, Nicholas; Meads, Andrew; Warren, Ian; Maddison, Ralph

2016-01-01

Background Participation in traditional center-based cardiac rehabilitation exercise programs (exCR) is limited by accessibility barriers. Mobile health (mHealth) technologies can overcome these barriers while preserving critical attributes of center-based exCR monitoring and coaching, but these opportunities have not yet been capitalized on. Objective We aimed to design and develop an evidence- and theory-based mHealth platform for remote delivery of exCR to any geographical location. Methods An iterative process was used to design and develop an evidence- and theory-based mHealth platform (REMOTE-CR) that provides real-time remote exercise monitoring and coaching, behavior change education, and social support. Results The REMOTE-CR platform comprises a commercially available smartphone and wearable sensor, custom smartphone and Web-based applications (apps), and a custom middleware. The platform allows exCR specialists to monitor patients’ exercise and provide individualized coaching in real-time, from almost any location, and provide behavior change education and social support. Intervention content incorporates Social Cognitive Theory, Self-determination Theory, and a taxonomy of behavior change techniques. Exercise components are based on guidelines for clinical exercise prescription. Conclusions The REMOTE-CR platform extends the capabilities of previous telehealth exCR platforms and narrows the gap between existing center- and home-based exCR services. REMOTE-CR can complement center-based exCR by providing an alternative option for patients whose needs are not being met. Remotely monitored exCR may be more cost-effective than establishing additional center-based programs. The effectiveness and acceptability of REMOTE-CR are now being evaluated in a noninferiority randomized controlled trial. PMID:27342791

Territorial organization of the lowland classic maya.

PubMed

Marcus, J

1973-06-01

Thus far I have discussed ancient Maya sociopolitical structure from the upper levels of the hierarchy downward. Let me now summarize their territorial organization from the bottom upward, starting at the hamlet level (Fig. 8). The smallest unit of settlement-one usually overlooked by archeological surveys in the lowland rain forest-was probably a cluster of thatched huts occupied by a group of related families; larger clusters may have been divided into four quadrants along the lines suggested by Coe (26). Because of the long fallow period (6 to 8 years) characteristic of slash-and-burn agriculture in the Petén, these small hamlets are presumed to have changed location over the years, although they probably shifted in a somewhat circular fashion around a tertiary ceremonial-civic center for whose maintenance they were partly responsible. These tertiary centers were spaced at fairly regular intervals around secondary ceremonial-civic centers with pyramids, carved monuments, and palace-like residences. In turn, the secondary centers occurred at such regular intervals as to form hexagonal patterns around primary centers, which were still larger, with acropolises, multiple ceremonial plazas, and greater numbers of monuments. In some cases, the distance between secondary centers was roughly twice the distance between secondary and tertiary centers, creating a lattice of nested hexagonal cells. This pattern, which conforms to a Western theoretical construct, was presumably caused by factors of service function, travel, and transport. The pattern was not recognized by the Maya at all. They simply recognized that a whole series of smaller centers were dependent on a primary center and therefore mentioned its emblem glyph. Linking the centers of the various hexagons were marriage alliances between members of royal dynasties, who had no kinship ties with the farmers in the hamlets. Out of the large number of primary centers available to them, the Maya selected four as regional capitals. True to their cosmology, the Maya regarded these capitals as associated with the four quadrants of their realm, regardless of their actual location. Each was the home city for a very important dynasty whose junior members probably ruled secondary centers. Since the hexagonal lattices were probably adjusted to variations in population density, each of the four quadrants of the Maya realm probably controlled a comparable number of persons. So strong was the cognized model that, despite the rise and fall of individual centers, there seem always to have been four capitals, each associated with a direction and, presumably, with a color. There is still a great deal to learn about the social, political, and territorial organization of the lowland Maya, and parts of the picture presented here need far more data for their confirmation. What seems likely is that the Maya had an overall quadripartite organization (rather than a core and buffer zone) and that within each quadrant there was at least a five-tiered administrative hierarchy of capital, secondary center, tertiary center, village, and hamlet. Perhaps most significant, there was no real conflict between the lattice-like network predicted by locational analysis and the cosmological four-part structure predicted by epigraphy and ethnology.

Conducting Research on the International Space Station Using the EXPRESS Rack Facilities

NASA Technical Reports Server (NTRS)

Thompson, Sean W.; Lake, Robert E.

2013-01-01

Eight "Expedite the Processing of Experiments to Space Station" (EXPRESS) Rack facilities are located within the International Space Station (ISS) laboratories to provide standard resources and interfaces for the simultaneous and independent operation of multiple experiments within each rack. Each EXPRESS Rack provides eight Middeck Locker Equivalent locations and two drawer locations for powered experiment equipment, also referred to as sub-rack payloads. Payload developers may provide their own structure to occupy the equivalent volume of one, two, or four lockers as a single unit. Resources provided for each location include power (28 Vdc, 0-500 W), command and data handling (Ethernet, RS-422, 5 Vdc discrete, +/- 5 Vdc analog), video (NTSC/RS 170A), and air cooling (0-200 W). Each rack also provides water cooling (500 W) for two locations, one vacuum exhaust interface, and one gaseous nitrogen interface. Standard interfacing cables and hoses are provided on-orbit. One laptop computer is provided with each rack to control the rack and to accommodate payload application software. Four of the racks are equipped with the Active Rack Isolation System to reduce vibration between the ISS and the rack. EXPRESS Racks are operated by the Payload Operations Integration Center at Marshall Space Flight Center and the sub-rack experiments are operated remotely by the investigating organization. Payload Integration Managers serve as a focal to assist organizations developing payloads for an EXPRESS Rack. NASA provides EXPRESS Rack simulator software for payload developers to checkout payload command and data handling at the development site before integrating the payload with the EXPRESS Functional Checkout Unit for an end-to-end test before flight. EXPRESS Racks began supporting investigations onboard ISS on April 24, 2001 and will continue through the life of the ISS.

Conducting Research on the International Space Station using the EXPRESS Rack Facilities

NASA Technical Reports Server (NTRS)

Thompson, Sean W.; Lake, Robert E.

2016-01-01

Eight "Expedite the Processing of Experiments to Space Station" (EXPRESS) Rack facilities are located within the International Space Station (ISS) laboratories to provide standard resources and interfaces for the simultaneous and independent operation of multiple experiments within each rack. Each EXPRESS Rack provides eight Middeck Locker Equivalent locations and two drawer locations for powered experiment equipment, also referred to as sub-rack payloads. Payload developers may provide their own structure to occupy the equivalent volume of one, two, or four lockers as a single unit. Resources provided for each location include power (28 Vdc, 0-500 W), command and data handling (Ethernet, RS-422, 5 Vdc discrete, +/- 5 Vdc analog), video (NTSC/RS 170A), and air cooling (0-200 W). Each rack also provides water cooling for two locations (500W ea.), one vacuum exhaust interface, and one gaseous nitrogen interface. Standard interfacing cables and hoses are provided on-orbit. One laptop computer is provided with each rack to control the rack and to accommodate payload application software. Four of the racks are equipped with the Active Rack Isolation System to reduce vibration between the ISS and the rack. EXPRESS Racks are operated by the Payload Operations Integration Center at Marshall Space Flight Center and the sub-rack experiments are operated remotely by the investigating organization. Payload Integration Managers serve as a focal to assist organizations developing payloads for an EXPRESS Rack. NASA provides EXPRESS Rack simulator software for payload developers to checkout payload command and data handling at the development site before integrating the payload with the EXPRESS Functional Checkout Unit for an end-to-end test before flight. EXPRESS Racks began supporting investigations onboard ISS on April 24, 2001 and will continue through the life of the ISS.

The dynamics and control of large flexible space structures, part 11

NASA Technical Reports Server (NTRS)

Bainum, Peter M.; Reddy, A. S. S. R; Diarra, Cheick M.; Li, Feiyue

1988-01-01

A mathematical model is developed to predict the dynamics of the proposed Spacecraft Control Laboratory Experiment during the stationkeeping phase. The Shuttle and reflector are assumed to be rigid, while the mass connecting the Shuttle to the reflector is assumed to be flexible with elastic deformations small as compared with its length. It is seen that in the presence of gravity-gradient torques, the system assumes a new equilibrium position primarily due to the offset in the mass attachment point to the reflector from the reflector's mass center. Control is assumed to be provided through the Shuttle's three torquers and throught six actuators located by painrs at two points on the mass and at the reflector mass center. Numerical results confirm the robustness of an LQR derived control strategy during stationkeeping with maximum control efforts significantly below saturation levels. The linear regulator theory is also used to derive control laws for the linearized model of the rigidized SCOLE configuration where the mast flexibility is not included. It is seen that this same type of control strategy can be applied for the rapid single axis slewing of the SCOLE through amplitudes as large as 20 degrees. These results provide a definite trade-off between the slightly larger slewing times with the considerable reduction in over-all control effort as compared with the results of the two point boundary value problem application of Pontryagin's Maximum Principle.

International Space Station (ISS)

NASA Image and Video Library

2001-02-01

The Marshall Space Flight Center (MSFC) is responsible for designing and building the life support systems that will provide the crew of the International Space Station (ISS) a comfortable environment in which to live and work. Scientists and engineers at the MSFC are working together to provide the ISS with systems that are safe, efficient, and cost-effective. These compact and powerful systems are collectively called the Environmental Control and Life Support Systems, or simply, ECLSS. This photograph shows the development Water Processor located in two racks in the ECLSS test area at the Marshall Space Flight Center. Actual waste water, simulating Space Station waste, is generated and processed through the hardware to evaluate the performance of technologies in the flight Water Processor design.

KSC-98pc268

NASA Image and Video Library

1998-02-05

KENNEDY SPACE CENTER, FLA. -- Technicians gather around the STS-90 Neurolab payload during weight and center-of-gravity measurements in KSC's Operations and Checkout Building. Investigations during the Neurolab mission will focus on the effects of microgravity on the nervous system. Specifically, experiments will study the adaptation of the vestibular system, the central nervous system, and the pathways that control the ability to sense location in the absence of gravity, as well as the effect of microgravity on a developing nervous system. The crew of STS-90, slated for launch in April, will include Commander Richard Searfoss, Pilot Scott Altman, Mission Specialists Richard Linnehan, Dafydd (Dave) Williams, M.D., and Kathryn (Kay) Hire, and Payload Specialists Jay Buckey, M.D., and James Pawelczyk, Ph.D

Clip gage attachment for frictionless measurement of displacement during high-temperature mechanical testing

DOEpatents

Alexander, David J.

1994-01-01

An attachment for placement between a test specimen and a remote clip gage extensometer providing improved fracture toughness tests of materials at elevated temperature. Using a cylindrical tube and axial rod in new relationship, the device transfers the displacement signal of the fracture toughness test specimen directly to a clip gage extensometer located outside the high temperature furnace. Virtually frictionless operation is assured by having the test specimen center one end of the rod in one end of the tube, while the clip gage extensometer arms center the other end of the rod in the other end of the tube. By providing positive control over both ends of both rod and tube, the attachment may be operated in orientations other than vertical.

Closeup view of the interior of an Aft Skirt being ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close-up view of the interior of an Aft Skirt being tested and prepared for mating with sub assemblies in the Solid Rocket Booster (SRB) Assembly and Refurbishment Facility at Kennedy Space Center. This view is showing the SRB Thrust Vector Control (TVC) System which includes independent auxiliary power units for each actuator to pressurize their respective hydraulic systems. When the Nozzle is mated with the Aft Skirt the two actuators, located on the left and right side of the TVC System in this view, can swivel it up to 3.5 degrees to redirect the thrust to steer and maintain the Shuttle's programmed trajectory. - Space Transportation System, Solid Rocket Boosters, Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Cryogenic Pressure Control Modeling for Ellipsoidal Space Tanks

NASA Technical Reports Server (NTRS)

Lopez, Alfredo; Grayson, Gary D.; Chandler, Frank O.; Hastings, Leon J.; Heyadat, Ali

2007-01-01

A computational fluid dynamics (CFD) model is developed to simulate pressure control of an ellipsoidal-shaped liquid hydrogen tank under external heating in normal gravity. Pressure control is provided by an axial jet thermodynamic vent system (TVS) centered within the vessel that injects cooler liquid into the tank, mixing the contents and reducing tank pressure. The two-phase cryogenic tank model considers liquid hydrogen in its own vapor with liquid density varying with temperature only and a fully compressible ullage. The axisymmetric model is developed using a custom version of the commercially available FLOW-31) software. Quantitative model validation is ,provided by engineering checkout tests performed at Marshall Space Flight Center in 1999 in support of the Solar Thermal Upper Stage_ Technology Demonstrator (STUSTD) program. The engineering checkout tests provide cryogenic tank self-pressurization test data at various heat leaks and tank fill levels. The predicted self-pressurization rates, ullage and liquid temperatures at discrete locations within the STUSTD tank are in good agreement with test data. The work presented here advances current CFD modeling capabilities for cryogenic pressure control and helps develop a low cost CFD-based design process for space hardware.

Shopping Centers: Their Development and Impact on a Community.

ERIC Educational Resources Information Center

Berezowski, P. E.; And Others

Presenting extensive background material on the development of shopping centers, this paper includes elementary and junior high school outdoor education activities centering upon shopping center studies. Background material includes analysis of the following: shopping center types (architecture, regional location, etc); land use (guidelines for…

Geological and geochemical aspects of uranium deposits: a selected, annotated bibliography. Vol. 2, Rev. 1. [490 references

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, J.M.; Brock, M.L.; Garland, P.A.

1979-07-01

This bibliography, a compilation of 490 references, is the second in a series compiled from the National Uranium Resource Evaluation (NURE) Bibliographic Data Base. This data base is one of six data bases created by the Ecological Sciences Information Center, Oak Ridge National Laboratory, for the Grand Junction Office of the Department of Energy. Major emphasis for this volume has been placed on uranium geology, encompassing deposition, genesis of ore deposits, and ore controls; and prospecting techniques, including geochemistry and aerial reconnaissance. The following indexes are provided to aid the user in locating references of interest: author, geographic location, quadranglemore » name, geoformational feature, taxonomic name, and keyword.« less

Surficial geology of part of Worth Center Quadrangle, Oswego County, New York

USGS Publications Warehouse

Miller, Todd S.

1980-01-01

The location and extent of six kinds of surficial deposits in part of Worth Center quadrangle, Oswego County, N.Y., are mapped on a 7.5-minute U.S. Geological Survey topographic map. The map was compiled to indicate the lithology and potential for groundwater development at any specific location. (USGS)

76 FR 62144 - Environmental Impact Statement for Implementation of Passenger Rail Service Between Tucson, AZ...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... characterized by urban densities at the northern and southern limits of the study area (Phoenix Metropolitan... communities located between these urban centers (primarily located in Pinal County). Historic rapid employment.... There are no public transportation services that directly connect the Phoenix and Tucson urban centers...

InfoPlace: A Case Study.

ERIC Educational Resources Information Center

Bosl, Rebecca

InfoPlace is a state-of-the-art vocational education program and special library. As part of the Cuyahoga County Library System of Greater Cleveland (Ohio), its resource center is located in the Maple Heights regional library. Although the resource center has one location, the staff of InfoPlace travels to the many branches of the Cuyahoga County…

Modeling, simulation, and high-autonomy control of a Martian oxygen production plant

NASA Technical Reports Server (NTRS)

Schooley, L. C.; Cellier, F. E.; Wang, F.-Y.; Zeigler, B. P.

1992-01-01

Progress on a project for the development of a high-autonomy intelligent command and control architecture for process plants used to produce oxygen from local planetary resources is reported. A distributed command and control architecture is being developed and implemented so that an oxygen production plant, or other equipment, can be reliably commanded and controlled over an extended time period in a high-autonomy mode with high-level task-oriented teleoperation from one or several remote locations. During the reporting period, progress was made at all levels of the architecture. At the remote site, several remote observers can now participate in monitoring the plant. At the local site, a command and control center was introduced for increased flexibility, reliability, and robustness. The local control architecture was enhanced to control multiple tubes in parallel, and was refined for increased robustness. The simulation model was enhanced to full dynamics descriptions.

The Skylab Airlock Module

NASA Technical Reports Server (NTRS)

1968-01-01

This illustration is a cutaway view of the external arrangement of the Airlock Module (AM). The aft end of the Docking Adapter mated to the AM, and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the 'utility center' of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

The Skylab Airlock Module

NASA Technical Reports Server (NTRS)

1972-01-01

This artist's concept is a cutaway illustration of the Skylab Airlock Module and its characteristics. The aft end of the Docking Adapter mated to the Airlock Module (AM), and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the 'utility center' of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

Skylab

NASA Image and Video Library

1968-01-01

This illustration is a cutaway view of the internal arrangement of the Airlock Module (AM). The aft end of the Docking Adapter mated to the AM, and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the "utility center" of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

Skylab

NASA Image and Video Library

1972-01-01

This artist's concept is a cutaway illustration of the Skylab Airlock Module and its characteristics. The aft end of the Docking Adapter mated to the Airlock Module (AM), and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the "utility center" of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

Skylab

NASA Image and Video Library

1968-01-01

This illustration is a cutaway view of the external arrangement of the Airlock Module (AM). The aft end of the Docking Adapter mated to the AM, and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the "utility center" of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

The Skylab Airlock Module

NASA Technical Reports Server (NTRS)

1968-01-01

This illustration is a cutaway view of the internal arrangement of the Airlock Module (AM). The aft end of the Docking Adapter mated to the AM, and served as the environmental, electrical, and communications control center. The docking adapter also contained the port through which the astronauts exited to perform extravehicular activity. The AM contained a turnel section through which Skylab crewmen could move between the workshop and the forward end of the airlock. It was encircled, for part of its length, at its aft end by the fixed Airlock Shroud (FAS), that had the same diameter as the workshop (22 feet) and was attached to the workshop's forward end. High pressure containers for oxygen and nitrogen providing Skylab's atmosphere, were mounted in the annular space between the outside of the tunnel and the inside of the shroud. The forward end of the FAS was the base on which the tubular structure supporting the solar observatory was mounted. Many of the supplies, and most of the control systems for Skylab were located in the AM; this module could well be the 'utility center' of the Skylab cluster. McDonnell Douglas fabricated the module with close Marshall Space Flight Center's involvement in design, development, and test activities.

"Survivor" Black Holes May Be Mid-Sized

NASA Astrophysics Data System (ADS)

2010-04-01

New evidence from NASA's Chandra X-ray Observatory and ESA's XMM-Newton strengthens the case that two mid-sized black holes exist close to the center of a nearby starburst galaxy. These "survivor" black holes avoided falling into the center of the galaxy and could be examples of the seeds required for the growth of supermassive black holes in galaxies, including the one in the Milky Way. For several decades, scientists have had strong evidence for two distinct classes of black hole: the stellar-mass variety with masses about ten times that of the Sun, and the supermassive ones, located at the center of galaxies, that range from hundreds of thousands to billions of solar masses. But a mystery has remained: what about black holes that are in between? Evidence for these objects has remained controversial, and until now there were no strong claims of more than one such black hole in a single galaxy. Recently, a team of researchers has found signatures in X-ray data of two mid-sized black holes in the starburst galaxy M82 located 12 million light years from Earth. "This is the first time that good evidence for two mid-sized black holes has been found in one galaxy," said Hua Feng of the Tsinghua University in China, who led two papers describing the results. "Their location near the center of the galaxy might provide clues about the origin of the Universe's largest black holes - supermassive black holes found in the centers of most galaxies." One possible mechanism for the formation of supermassive black holes involves a chain reaction of collisions of stars in compact star clusters that results in the buildup of extremely massive stars, which then collapse to form intermediate-mass black holes. The star clusters then sink to the center of the galaxy, where the intermediate-mass black holes merge to form a supermassive black hole. In this picture, clusters that were not massive enough or close enough to the center of the galaxy to fall in would survive, as would any black holes they contain. "We can't say whether this process actually occurred in M82, but we do know that both of these possible mid-sized black holes are located in or near star clusters," said Phil Kaaret from the University of Iowa, who co-authored both papers. "Also, M82 is the nearest place to us where the conditions are similar to those in the early Universe, with lots of stars forming." The evidence for these two "survivor" black holes comes from how their X-ray emission varies over time and analysis of their X-ray brightness and spectra, i.e., the distribution of X-rays with energy. Chandra and XMM-Newton data show that the X-ray emission for one of these objects changes in a distinctive manner similar to stellar-mass black holes found in the Milky Way. Using this information and theoretical models, the team estimated this black hole's mass is between 12,000 and 43,000 times the mass of the Sun. This mass is large enough for the black hole to generate copious X-rays by pulling gas directly from its surroundings, rather than from a binary companion, like with stellar-mass black holes. The black hole is located at a projected distance of 290 light years from the center of M82. The authors estimate that, at this close distance, if the black hole was born at the same time as the galaxy and its mass was more than about 30,000 solar masses it would have been pulled into the center of the galaxy. That is, it may have just escaped falling into the supermassive black hole that is presumably located in the center of M82. The second object, located 600 light years in projection away from the center of M82, was observed by both Chandra and XMM-Newton. During X-ray outbursts, periodic and random variations normally present in the X-ray emission disappear, a strong indication that a disk of hot gas dominates the X-ray emission. A detailed fit of the X-ray data indicates that the disk extends all the way to the innermost stable orbit around the black hole. Similar behavior has been seen from stellar-mass black holes in our Galaxy, but this is the first likely detection in a candidate intermediate-mass black hole. The radius of the innermost stable orbit depends only on the mass and spin of the black hole. The best model for the X-ray emission implies a rapidly spinning black hole with mass in the range 200 to 800 times the mass of the Sun. The mass agrees with theoretical estimates for a black hole created in a star cluster by runaway collisions of stars. "This result is one of the strongest pieces of evidence to date for the existence of an intermediate-mass black hole," said Feng. "This looks just like well-studied examples of stellar-mass black holes, except for being more than 20 times as massive." The two papers describing these results recently appeared in The Astrophysical Journal. NASA's Marshall Space Flight Center in Huntsville, Ala., manages the Chandra program for NASA's Science Mission Directorate in Washington. The Smithsonian Astrophysical Observatory controls Chandra's science and flight operations from Cambridge, Mass. The XMM-Newton spacecraft is controlled by the European Space Operations Center. The XMM-Newton Science Operations Center situated at ESAC in Villafranca, Spain, manages observation requests and receives XMM-Newton data. The XMM-Newton Survey Science Centre at Leicester University, UK, processes and correlates all XMM-Newton observations with existing sky data held elsewhere in the world. More information, including images and other multimedia, can be found at: http://chandra.harvard.edu and http://chandra.nasa.gov and http://www.esa.int/esaSC/

Staphylococcus aureus recovery from environmental and human locations in 2 collegiate athletic teams.

PubMed

Oller, Anna R; Province, Larry; Curless, Brian

2010-01-01

Staphylococcus aureus is spread via direct contact with persons and indirect contact via environmental surfaces such as weight benches. Athletes participating in direct-contact sports have an increased risk of acquiring S aureus infections. To determine (1) potential environmental reservoirs of S aureus in football and wrestling locker rooms and weight rooms, (2) environmental bacterial status after employing more stringent cleaning methods, (3) differences in colonization rates between athletes and nonathletes, (4) exposed body locations where Staphylococcus was recovered more frequently, and (5) personal hygiene practices of athletes and nonathletes. Cross-sectional study. Locker room and strengthening and conditioning facilities at a National Collegiate Athletic Association Division II university. Collegiate football players and wrestlers, with nonathlete campus residents serving as the control group. Infection control methods, education of the custodial staff, and education of the athletes regarding the Centers for Disease Control and Prevention guidelines for infection prevention. Cultures were taken from the participants' noses, fingertips, knuckles, forearms, and shoes and from the environment. Before the intervention, from the 108 environmental samples taken from the football locker room and weight room, 26 (24%) contained methicillin-susceptible S aureus (MSSA) and 33 (31%) contained methicillin-resistant S aureus (MRSA). From the 39 environmental samples taken from the wrestling locker room and pit areas, 1 (3%) contained MSSA and 4 (10%) contained MRSA. The MRSA rates were different between the 2 locations according to a chi(2) test (P = .01). Seven MRSA isolates were recovered from football players and 1 from a wrestler; no MRSA isolates were recovered from the control group. The fingertip location of S aureus recovery from football players was significant when compared with both other locations in football players and fingertips in wrestlers and the control group (P < .05). Football players and wrestlers shared more personal items than the control group (P < .05). After the intervention, the football locker room and weight room samples were negative for S aureus. Intact strengthening and conditioning equipment, proper hygiene, and proper disinfection methods lowered both environmental and human S aureus recovery at 1 university.

Optical position measurement for a Large Gap Magnetic Suspension System

NASA Technical Reports Server (NTRS)

Welch, Sharon S.; Shelton, Kevin J.; Clemmons, James I.

1991-01-01

This paper describes the design of an optical position measurement system which is being built as part of the NASA Langley Large Gap Magnetic Suspension System (LGMSS). The LGMSS is a five degree-of-freedom, large-gap magnetic suspension system which is being built for Langley Research Center as part of the Advanced Controls Test Facility (ACTF). The LGMSS consists of a planar array of electromagnets which levitate and position a cylindrically shaped model containing a permanent magnet core. The optical position measurement system provides information on the location and orientation of the model to the LGMSS control system to stabilize levitation of the model.

Ancient techniques for new materials

NASA Technical Reports Server (NTRS)

2000-01-01

NASA is looking to biological techniques that are millions of years old to help it develop new materials and technologies for the 21st century. Sponsored by NASA, Viola Vogel, director of Washington University's Center for Nanotechnology and a principal investigator for the microgravity biotechnology program, is researching a monorail on a nanoscale to learn how to control translational motion of motor proteins in nonbiological environments in order to transport cargo between user-specified locations. Shear-deposition of Teflon on glass (top) is used in Viola Vogel's lab to create a nanogrooved surface. The topography controls the path that microtubules take as they shuttle nano-sized cargo between user-defined destinations.

Saskatchewan Forest Fire Control Centre Surface Meteorological Data

NASA Technical Reports Server (NTRS)

Hall, Forrest G. (Editor); Newcomer, Jeffrey A. (Editor); Funk, Barry; Strub, Richard

2000-01-01

The Saskatchewan Forest Fire Control Centre (SFFCC) provided surface meteorological data to BOREAS from its archive. This data set contains hourly surface meteorological data from 18 of the Meteorological stations located across Saskatchewan. Included in these data are parameters of date, time, temperature, relative humidity, wind direction, wind speed, and precipitation. Temporally, the data cover the period of May through September of 1994 and 1995. The data are provided in comma-delimited ASCII files, and are classified as AFM-Staff data. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Microgravity

NASA Image and Video Library

2000-12-15

NASA is looking to biological techniques that are millions of years old to help it develop new materials and technologies for the 21st century. Sponsored by NASA, Viola Vogel, director of Washington University's Center for Nanotechnology and a principal investigator for the microgravity biotechnology program, is researching a monorail on a nanoscale to learn how to control translational motion of motor proteins in nonbiological environments in order to transport cargo between user-specified locations. Shear-deposition of Teflon on glass (top) is used in Viola Vogel's lab to create a nanogrooved surface. The topography controls the path that microtubules take as they shuttle nano-sized cargo between user-defined destinations.

A multicriteria decision making approach based on fuzzy theory and credibility mechanism for logistics center location selection.

PubMed

Wang, Bowen; Xiong, Haitao; Jiang, Chengrui

2014-01-01

As a hot topic in supply chain management, fuzzy method has been widely used in logistics center location selection to improve the reliability and suitability of the logistics center location selection with respect to the impacts of both qualitative and quantitative factors. However, it does not consider the consistency and the historical assessments accuracy of experts in predecisions. So this paper proposes a multicriteria decision making model based on credibility of decision makers by introducing priority of consistency and historical assessments accuracy mechanism into fuzzy multicriteria decision making approach. In this way, only decision makers who pass the credibility check are qualified to perform the further assessment. Finally, a practical example is analyzed to illustrate how to use the model. The result shows that the fuzzy multicriteria decision making model based on credibility mechanism can improve the reliability and suitability of site selection for the logistics center.

A Multicriteria Decision Making Approach Based on Fuzzy Theory and Credibility Mechanism for Logistics Center Location Selection

PubMed Central

Wang, Bowen; Jiang, Chengrui

2014-01-01

As a hot topic in supply chain management, fuzzy method has been widely used in logistics center location selection to improve the reliability and suitability of the logistics center location selection with respect to the impacts of both qualitative and quantitative factors. However, it does not consider the consistency and the historical assessments accuracy of experts in predecisions. So this paper proposes a multicriteria decision making model based on credibility of decision makers by introducing priority of consistency and historical assessments accuracy mechanism into fuzzy multicriteria decision making approach. In this way, only decision makers who pass the credibility check are qualified to perform the further assessment. Finally, a practical example is analyzed to illustrate how to use the model. The result shows that the fuzzy multicriteria decision making model based on credibility mechanism can improve the reliability and suitability of site selection for the logistics center. PMID:25215319

Apollo 9 Mission image - S0-65 Multispectral Photography - Texas

NASA Image and Video Library

2009-02-19

AS09-26A-3727A (8 March 1969) --- Color infrared photograph of the Texas Gulf Coast, Galveston Bay to Matagorda Bay, as seen from the Apollo 9 spacecraft during it 78th revolution of Earth. Houston is located at right center edge of photograph. Also visible are Galveston, Texas City, Manned Spacecraft Center, and Freeport. The mouth of the Colorado River is located near left center edge of picture. This picture was taken as a part of the SO65 Multispectral Terrain Photography Experiment.

KENNEDY SPACE CENTER, FLA. - KSC Director Jim Kennedy (center) makes a presentation to NASA and other officials about the benefits of locating NASA’s new Shared Services Center in the Central Florida Research Park, near Orlando. Central Florida leaders are proposing the research park as the site for the NASA Shared Services Center. The center would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Six sites around the U.S. are under consideration by NASA.

NASA Image and Video Library

2004-02-19

KENNEDY SPACE CENTER, FLA. - KSC Director Jim Kennedy (center) makes a presentation to NASA and other officials about the benefits of locating NASA’s new Shared Services Center in the Central Florida Research Park, near Orlando. Central Florida leaders are proposing the research park as the site for the NASA Shared Services Center. The center would centralize NASA’s payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Six sites around the U.S. are under consideration by NASA.

The study on the Layout of the Charging Station in Chengdu

NASA Astrophysics Data System (ADS)

Cai, yun; Zhang, wanquan; You, wei; Mao, pan

2018-03-01

In this paper, the comprehensive analysis of the factors affecting the layout of the electric car, considering the principle of layout of the charging station. Using queuing theory in operational research to establish mathematical model and basing on the principle of saving resource and convenient owner to optimize site number. Combining the theory of center to determine the service radius, Using the Gravity method to determine the initial location, Finally using the method of center of gravity to locate the charging station’s location.

[Telematics equipment for poison control surveillance. Its applications in the health management of relevant chemical incidents].

PubMed

Butera, R; Locatelli, C; Gandini, C; Minuco, G; Mazzoleni, M C; Giordano, A; Zanuti, M; Varango, C; Petrolini, V; Candura, S M; Manzo, L

1997-01-01

Health management of major chemical incidents requires a close collaboration between rescuers (on the disaster site and in the emergency department) and the poison center. The study tested telematic technologies allowing telepresence and teleconsulting, a real time and continuous connection among health care personnel and toxicologists involved in the management of the emergency. The link between the poison center (PC) and the emergency department in the local hospital is provided by a ISDN operating video conferencing system, while the data transmission from the site of the accident to the PC is achieved with a personal computer and GSM cellular data transmission. Toxicological databases and risk assessment software are integrated in the system, to support information sharing. To test such instruments in operative nearly realistic conditions, the main phase of the study has implemented simulated chemical disasters in different locations in Italy. Instruments for telepresence and teleconsulting have been effectively utilized to evaluate from a remote location the scenario and the severity of the accident, by inspecting either specific details or the whole scene, to enable PC guiding the triage of the victims before and after hospitalization, to utilize and share data, such as intervention protocols or patient records, and to document all the activities. In summary, this experience shows that the telematic link allows the toxicologists of the poison center to rapidly understand the situation, and to correctly learn about the conditions of patients with the help of images. The results of this study indicate the valuable benefits of telematic instruments for the health care in case of major chemical disasters occurring in a remote geographical location or in an area which lacks local toxicological experts, where specialized expertise can be achieved by the use of telematic technologies.

A multilevel intervention to increase physical activity and improve healthy eating and physical literacy among young children (ages 3-5) attending early childcare centres: the Healthy Start-Départ Santé cluster randomised controlled trial study protocol.

PubMed

Bélanger, Mathieu; Humbert, Louise; Vatanparast, Hassan; Ward, Stéphanie; Muhajarine, Nazeem; Chow, Amanda Froehlich; Engler-Stringer, Rachel; Donovan, Denise; Carrier, Natalie; Leis, Anne

2016-04-12

Childhood obesity is a growing concern for public health. Given a majority of children in many countries spend approximately 30 h per week in early childcare centers, this environment represents a promising setting for implementing strategies to foster healthy behaviours for preventing and controlling childhood obesity. Healthy Start-Départ Santé was designed to promote physical activity, physical literacy, and healthy eating among preschoolers. The objectives of this study are to assess the effectiveness of the Healthy Start-Départ Santé intervention in improving physical activity levels, physical literacy, and healthy eating among preschoolers attending early childcare centers. This study follows a cluster randomized controlled trial design in which the childcare centers are randomly assigned to receive the intervention or serve as usual care controls. The Healthy Start-Départ Santé intervention is comprised of interlinked components aiming to enable families and educators to integrate physical activity and healthy eating in the daily lives of young children by influencing factors at the intrapersonal, interpersonal, organizational, community, physical environment and policy levels. The intervention period, spanning 6-8 months, is preceded and followed by data collections. Participants are recruited from 61 childcare centers in two Canadian provinces, New Brunswick and Saskatchewan. Centers eligible for this study have to prepare and provide meals for lunch and have at least 20 children between the ages of 3 and 5. Centers are excluded if they have previously received a physical activity or nutrition promoting intervention. Eligible centers are stratified by province, geographical location (urban or rural) and language (English or French), then recruited and randomized using a one to one protocol for each stratum. Data collection is ongoing. The primary study outcomes are assessed using accelerometers (physical activity levels), the Test of Gross Motor Development-II (physical literacy), and digital photography-assisted weighted plate waste (food intake). The multifaceted approach of Healthy Start-Départ Santé positions it well to improve the physical literacy and both dietary and physical activity behaviors of children attending early childcare centers. The results of this study will be of relevance given the overwhelming prevalence of overweight and obesity in children worldwide. NCT02375490 (ClinicalTrials.gov registry).

Medial knee loading is altered in subjects with early osteoarthritis during gait but not during step-up-and-over task

PubMed Central

Wesseling, Mariska; Smith, Colin R.; Thelen, Darryl G.; Verschueren, Sabine; Jonkers, Ilse

2017-01-01

This study evaluates knee joint loading during gait and step-up-and-over tasks in control subjects, subjects with early knee OA and those with established knee OA. Thirty-seven subjects with varying degrees of medial compartment knee OA severity (eighteen with early OA and sixteen with established OA), and nineteen healthy controls performed gait and step-up-and-over tasks. Knee joint moments, contact forces (KCF), the magnitude of contact pressures and center of pressure (CoP) location were analyzed for the three groups for both activities using a multi-body knee model with articular cartilage contact, 14 ligaments, and six degrees of freedom tibiofemoral and patellofemoral joints. During gait, the first peak of the medial KCF was significantly higher for patients with early knee OA (p = 0.048) and established knee OA (p = 0.001) compared to control subjects. Furthermore, the medial contact pressure magnitudes and CoP location were significantly different in both groups of patients compared to controls. Knee rotation moments (KRMs) and external rotation angles were significantly higher during early stance in both patient groups (p < 0.0001) compared to controls. During step-up-and-over, there was a high variability between the participants and no significant differences in KCF were observed between the groups. Knee joint loading and kinematics were found to be altered in patients with early knee OA only during gait. This is an indication that an excessive medial KCF and altered loading location, observed in these patients, is a contributor to early progression of knee OA. PMID:29117248

A Learning Center Can Happen to You.

ERIC Educational Resources Information Center

Currey, Mary Nell; Hancock, Vickie

This booklet describes the development and activities of the Clinton Park Elementary School Media Center, a first and second grade learning center located in Clinton, Mississippi. Following introductory materials on the establishment of the media center in September 1975 and federal funding of media center projects from 1975 to 1978, information…

Low-speed wind-tunnel test of a STOL supersonic-cruise fighter concept

NASA Technical Reports Server (NTRS)

Coe, Paul L., Jr.; Riley, Donald R.

1988-01-01

A wind-tunnel investigation was conducted to examine the low-speed static stability and control characteristics of a 0.10 scale model of a STOL supersonic cruise fighter concept. The concept, referred to as a twin boom fighter, was designed as a STOL aircraft capable of efficient long range supersonic cruise. The configuration name is derived from the long twin booms extending aft of the engine to the twin vertical tails which support a high center horizontal tail. The propulsion system features a two dimensional thrust vectoring exhaust nozzle which is located so that the nozzle hinge line is near the aircraft center of gravity. This arrangement is intended to allow large thrust vector angles to be used to obtain significant values of powered lift, while minimizing pitching moment trim changes. Low speed stability and control information was obtained over an angle of attack range including the stall. A study of jet induced power effects was included.

The Virtual Mission Operations Center

NASA Technical Reports Server (NTRS)

Moore, Mike; Fox, Jeffrey

1994-01-01

Spacecraft management is becoming more human intensive as spacecraft become more complex and as operations costs are growing accordingly. Several automation approaches have been proposed to lower these costs. However, most of these approaches are not flexible enough in the operations processes and levels of automation that they support. This paper presents a concept called the Virtual Mission Operations Center (VMOC) that provides highly flexible support for dynamic spacecraft management processes and automation. In a VMOC, operations personnel can be shared among missions, the operations team can change personnel and their locations, and automation can be added and removed as appropriate. The VMOC employs a form of on-demand supervisory control called management by exception to free operators from having to actively monitor their system. The VMOC extends management by exception, however, so that distributed, dynamic teams can work together. The VMOC uses work-group computing concepts and groupware tools to provide a team infrastructure, and it employs user agents to allow operators to define and control system automation.

Roles of Knowledge in Motor Learning.

DTIC Science & Technology

1987-02-02

Aalgorithms, and much of traditional adaptive control. /-/ COPY Accesion For NTIS CRA&I -, OTIC TAB - ~ ~Jj: t:! C t~ 3 ...... . .. J- o F-- --*-- * F- %r.o...W [WX c (3.9) - - w, 0 , V 37 V#J’ ¢7" --𔄁 .- .,,,77, . ° .. . o -. . -. . -. " . . " " . % . % " " . ", " - . -. . . % % 7- _ - 2...require the principal moments of inertia ’.39 O . 1, 12, I, the location of the center of mass c , and the orientation p.R of Q with respect to P. The

Environment sanitation handbook

NASA Technical Reports Server (NTRS)

1973-01-01

The environmental Sanitation handbook provides guidance in the implementation of the basic provisions of occupational medicine and environmental health programs to environmental sanitation. It presents methods and procedures useful for the control of those sanitation factors which could create discomfort and illness in man or do harm to his environment. The provisions of this handbook are applicable to all organizational elements of the Kennedy Space Center (KSC),NASA, and to its associated contractors located at KSC in accordance with the terms of their respective contracts.

60. VIEW OF THE CURRENT TRANSFORMER VAULT. THIS CURRENT TRANSFORMER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. VIEW OF THE CURRENT TRANSFORMER VAULT. THIS CURRENT TRANSFORMER WAS USED TO SENSE HIGH CURRENT BEING GENERATED ON GENERATOR NUMBER 3 AND REDUCE IT TO A LOWER, EXACT ANALOG VALUE THAT COULD BE SAFELY HANDLED AND MONITORED WITH THE CONTROL CIRCUITRY. THE CURRENT TRANSFORMER IS LOCATED IN THE CENTER OF THE PHOTOGRAPH. THE CONNECTING BUS ABOVE THE TRANSFORMER WAS REMOVED FOR SALVAGE. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Advanced Aircrew Display Symposium Proceedings (5th) Held at the Naval Air Test Center, Patuxent, Maryland on 15-16 September 1981

DTIC Science & Technology

1981-01-01

cruisc air combat , etc. These are selected from the keyboard located at the forward end o.f the left console. Tie miscion phase packager of...and brightness test - low ambient phase Color discrimination performance was assessed by a comparative procedure which best reflects the operational...flight information for air to air , air to surface, and navigation phases of the mission. UP FRONT CONTROL (UPC- MASTER fHEAD-UP MASTER DISPLAY

Aerospace applications of integer and combinatorial optimization

NASA Technical Reports Server (NTRS)

Padula, S. L.; Kincaid, R. K.

1995-01-01

Research supported by NASA Langley Research Center includes many applications of aerospace design optimization and is conducted by teams of applied mathematicians and aerospace engineers. This paper investigates the benefits from this combined expertise in solving combinatorial optimization problems. Applications range from the design of large space antennas to interior noise control. A typical problem, for example, seeks the optimal locations for vibration-damping devices on a large space structure and is expressed as a mixed/integer linear programming problem with more than 1500 design variables.

Technical Update: Johnson Space Center system using a solid electrolytic cell in a remote location to measure oxygen fugacities in CO/CO2 controlled-atmosphere furnaces

NASA Technical Reports Server (NTRS)

Jurewicz, A. J. G.; Williams, R. J.; Le, L.; Wagstaff, J.; Lofgren, G.; Lanier, A.; Carter, W.; Roshko, A.

1993-01-01

Details are given for the design and application of a (one atmosphere) redox-control system. This system differs from that given in NASA Technical Memorandum 58234 in that it uses a single solid-electrolytic cell in a remote location to measure the oxygen fugacities of multiple CO/CO2 controlled-atmosphere furnaces. This remote measurement extends the range of sample-furnace conditions that can be measured using a solid-electrolytic cell, and cuts costs by extending the life of the sensors and by minimizing the number of sensors in use. The system consists of a reference furnace and an exhaust-gas manifold. The reference furnace is designed according to the redox control system of NASA Technical Memorandum 58234, and any number of CO/CO2 controlled-atmosphere furnaces can be attached to the exhaust-gas manifold. Using the manifold, the exhaust gas from individual CO/CO2 controlled atmosphere furnaces can be diverted through the reference furnace, where a solid-electrolyte cell is used to read the ambient oxygen fugacity. The oxygen fugacity measured in the reference furnace can then be used to calculate the oxygen fugacity in the individual CO/CO2 controlled-atmosphere furnace. A BASIC computer program was developed to expedite this calculation.

TASAR Flight Trial 2: Assessment of Air Traffic Controller Acceptability of TASAR Requests

NASA Technical Reports Server (NTRS)

Idris, Husni; Enea, Gabriele

2016-01-01

In support of the Flight Trial (FT-2) of NASA's prototype of the Traffic Aware Strategic Aircrew Requests (TASAR) concept, observations were conducted at the air traffic facilities to identify and assess the main factors that affect the acceptability of pilot requests by air traffic controllers. Two observers shadowed air traffic controllers at the Atlanta (ZTL) and Jacksonville (ZJX) air traffic control centers as the test flight pilot made pre-scripted requests to invoke acceptability issues and then they interviewed the observed and other controllers voluntarily. Fifty controllers were interviewed with experience ranging from one to thirty-five years. All interviewed controllers were enthusiastic about the technology and accounting for sector boundaries in pilot requests, particularly if pilots can be made aware of high workload situations. All interviewed controllers accept more than fifty percent of pilot requests; forty percent of them reject less than ten percent of requests. The most common reason for rejecting requests is conflicting with traffic followed by violating letters of agreement (LOAs) and negatively impacting neighboring sector workload, major arrival and departure flows and flow restrictions. Thirty-six requests were made during the test, eight of which were rejected due to: the aircraft already handed off to another sector, violating LOA, opposing traffic, intruding into an active special use airspace (SUA), intruding into another center, weather, and unfamiliarity with the requested waypoint. Nine requests were accepted with delay mostly because the controller needed to locate unfamiliar waypoints or to coordinate with other controllers.

Attention doesn’t slide: spatiotopic updating after eye movements instantiates a new, discrete attentional locus

PubMed Central

Marino, Alexandria C.; Chun, Marvin M.

2011-01-01

During natural vision, eye movements can drastically alter the retinotopic (eye-centered) coordinates of locations and objects, yet the spatiotopic (world-centered) percept remains stable. Maintaining visuospatial attention in spatiotopic coordinates requires updating of attentional representations following each eye movement. However, this updating is not instantaneous; attentional facilitation temporarily lingers at the previous retinotopic location after a saccade, a phenomenon known as the retinotopic attentional trace. At various times after a saccade, we probed attention at an intermediate location between the retinotopic and spatiotopic locations to determine whether a single locus of attentional facilitation slides progressively from the previous retinotopic location to the appropriate spatiotopic location, or whether retinotopic facilitation decays while a new, independent spatiotopic locus concurrently becomes active. Facilitation at the intermediate location was not significant at any time, suggesting that top-down attention can result in enhancement of discrete retinotopic and spatiotopic locations without passing through intermediate locations. PMID:21258903

Vasovagal reactions in whole blood donors at 3 REDS-II blood centers in Brazil

PubMed Central

Goncalez, T. T.; Sabino, E. C.; Schlumpf, K.S.; Wright, D.J.; Leao, S.; Sampaio, D.; Takecian, P. L.; Carneiro-Proietti, AB; Murphy, E.; Busch, M.; Custer, B.

2013-01-01

Background In Brazil little is known about adverse reactions during donation and the donor characteristics that may be associated with such events. Donors are offered snacks and fluids prior to donating and are required to consume a light meal after donation. For these reasons the frequency of reactions may be different than those observed in other countries. Methods A cross-sectional study was conducted of eligible whole blood donors at three large blood centers located in Brazil between July 2007 and December 2009. Vasovagal reactions (VVRs) along with donor demographic and biometric data were collected. Reactions were defined as any presyncopal or syncopal event during the donation process. Multivariable logistic regression was performed to identify predictors of VVRs. Results Of 724,861 donor presentations, 16,129 (2.2%) VVRs were recorded. Rates varied substantially between the three centers: 53, 290 and 381 per 10,000 donations in Recife, São Paulo and Belo Horizonte, respectively. Although the reaction rates varied, the donor characteristics associated with VVRs were similar [younger age (18–29), replacement donors, first time donors, low estimated blood volume (EBV)]. In multivariable analysis controlling for differences between the donor populations in each city younger age, first-time donor status and lower EBV were the factors most associated with reactions. Conclusion Factors associated with VVRs in other locations are also evident in Brazil. The difference in VVR rates between the three centers might be due to different procedures for identifying and reporting the reactions. Potential interventions to reduce the risk of reactions in Brazil should be considered. PMID:22073941

Perceived displacement explains wolfpack effect

PubMed Central

Šimkovic, Matúš; Träuble, Birgit

2014-01-01

We investigate the influence of perceived displacement of moving agent-like stimuli on the performance in dynamic interactive tasks. In order to reliably measure perceived displacement we utilize multiple tasks with different task demands. The perceived center of an agent's body is displaced in the direction in which the agent is facing and this perceived displacement is larger than the theoretical position of the center of mass would predict. Furthermore, the displacement in the explicit judgment is dissociated from the displacement obtained by the implicit measures. By manipulating the location of the pivot point, we show that it is not necessary to postulate orientation as an additional cue utilized by perception, as has been suggested by earlier studies. These studies showed that the agent's orientation influences the detection of chasing motion and the detection-related performance in interactive tasks. This influence has been labeled wolfpack effect. In one of the demonstrations of the wolfpack effect participants control a green circle on a display with a computer mouse. It has been shown that participants avoid display areas with agents pointing toward the green circle. Participants do so in favor of areas where the agents point in the direction perpendicular to the circle. We show that this avoidance behavior arises because the agent's pivot point selected by the earlier studies is different from where people locate the center of agent's body. As a consequence, the nominal rotation confounds rotation and translation. We show that the avoidance behavior disappears once the pivot point is set to the center of agent's body. PMID:25566114

Structure and Development of the Subesophageal Zone of the Drosophila Brain. II. Sensory Compartments

PubMed Central

Kendroud, Sarah; Bohra, Ali Asgar; Kuert, Philipp A.; Nguyen, Bao; Guillermin, Oriane; Sprecher, Simon G.; Reichert, Heinrich; VijayRaghavan, Krishnaswamy; Hartenstein, Volker

2018-01-01

The subesophageal zone (SEZ) of the Drosophila brain processes mechanosensory and gustatory sensory input from sensilla located on the head, mouth cavity and trunk. Motor output from the SEZ directly controls the movements involved in feeding behavior. In an accompanying paper (Hartenstein et al., 2017) we analyzed the systems of fiber tracts and secondary lineages to establish reliable criteria for defining boundaries between the four neuromeres of the SEZ, as well as discrete longitudinal neuropil domains within each SEZ neuromere. Here we use this anatomical framework to systematically map the sensory projections entering the SEZ throughout development. Our findings show a continuity between larval and adult sensory neuropils. Gustatory axons from internal and external taste sensilla of the larva and adult form two closely related sensory projections, (1) the anterior central sensory center (ACSC) located deep in the ventromedial neuropil of the tritocerebrum and mandibular neuromere, and (2) the anterior ventral sensory center (AVSC), occupying a superficial layer within the ventromedial tritocerebrum. Additional, presumed mechanosensory terminal axons entering via the labial nerve define the ventromedial sensory center (VMSC) in the maxilla and labium. Mechanosensory afferents of the massive array of chordotonal organs (Johnston’s organ) of the adult antenna project into the centrolateral neuropil column of the anterior SEZ, creating the antenno-mechanosensory and motor center (AMMC). Dendritic projections of dye back-filled motor neurons extend throughout a ventral layer of the SEZ, overlapping widely with the AVSC and VMSC. Our findings elucidate fundamental structural aspects of the developing sensory systems in Drosophila. PMID:28875566

75 FR 47026 - Cedar Creek and Belle Grove National Historical Park Advisory Commission; Notice of Public Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-04

.... Location: Warren County Government Center, 220 North Commerce Avenue, Front Royal, VA. Date: December 16... 16, 2011 Location: Warren County Government Center, 220 North Commerce Avenue, Front Royal, VA. All meetings will convene at 8:30 a.m. and are open to the public. FOR FURTHER INFORMATION CONTACT: Diann Jacox...

Cluster analysis for determining distribution center location

NASA Astrophysics Data System (ADS)

Lestari Widaningrum, Dyah; Andika, Aditya; Murphiyanto, Richard Dimas Julian

2017-12-01

Determination of distribution facilities is highly important to survive in the high level of competition in today’s business world. Companies can operate multiple distribution centers to mitigate supply chain risk. Thus, new problems arise, namely how many and where the facilities should be provided. This study examines a fast-food restaurant brand, which located in the Greater Jakarta. This brand is included in the category of top 5 fast food restaurant chain based on retail sales. There were three stages in this study, compiling spatial data, cluster analysis, and network analysis. Cluster analysis results are used to consider the location of the additional distribution center. Network analysis results show a more efficient process referring to a shorter distance to the distribution process.

Epidemic assistance by the Centers for Disease Control and Prevention: role of the Epidemic Intelligence Service, 1946-2005.

PubMed

Thacker, Stephen B; Stroup, Donna F; Sencer, David J

2011-12-01

Since 1946, the Centers for Disease Control and Prevention has responded to urgent requests from US states, federal agencies, and international organizations through epidemic-assistance investigations (Epi-Aids). The authors describe the first 60 years of Epi-Aids, breadth of problems addressed, evolution of methodologies, scope of activities, and impact of investigations on population health. They reviewed Epi-Aid reports and EIS Bulletins, contacted current and former Epidemic Intelligence Service staff, and systematically searched the PubMed and Web of Science databases. They abstracted information on dates, location, staff involved, health problems, methods, and impacts of investigations according to a preplanned protocol. They assessed the methods presented as well as the quality of reports. During 1946-2005, a total of 4,484 investigations of health events were initiated by 2,815 Epidemic Intelligence Service officers. In the early years, the majority were in response to infectious agents, although environmental problems emerged. Investigations in subsequent years focused on occupational conditions, birth defects, reproductive health, tobacco use, cancer, violence, legal debate, and terrorism. These Epi-Aids heralded expansion of the agency's mission and presented new methods in statistics and epidemiology. Recommendations from Epi-Aids led to policy implementation, evaluation, or modification. Epi-Aids provide the Centers for Disease Control and Prevention with the agility to respond rapidly to public health crises.

Multiple Autonomous Discrete Event Controllers for Constellations

NASA Technical Reports Server (NTRS)

Esposito, Timothy C.

2003-01-01

The Multiple Autonomous Discrete Event Controllers for Constellations (MADECC) project is an effort within the National Aeronautics and Space Administration Goddard Space Flight Center's (NASA/GSFC) Information Systems Division to develop autonomous positioning and attitude control for constellation satellites. It will be accomplished using traditional control theory and advanced coordination algorithms developed by the Johns Hopkins University Applied Physics Laboratory (JHU/APL). This capability will be demonstrated in the discrete event control test-bed located at JHU/APL. This project will be modeled for the Leonardo constellation mission, but is intended to be adaptable to any constellation mission. To develop a common software architecture. the controllers will only model very high-level responses. For instance, after determining that a maneuver must be made. the MADECC system will output B (Delta)V (velocity change) value. Lower level systems must then decide which thrusters to fire and for how long to achieve that (Delta)V.

SES cupola interactive display design environment

NASA Technical Reports Server (NTRS)

Vu, Bang Q.; Kirkhoff, Kevin R.

1989-01-01

The Systems Engineering Simulator, located at the Lyndon B. Johnson Space Center in Houston, Texas, is tasked with providing a real-time simulator for developing displays and controls targeted for the Space Station Freedom. These displays and controls will exist inside an enclosed workstation located on the space station. The simulation is currently providing the engineering analysis environment for NASA and contractor personnel to design, prototype, and test alternatives for graphical presentation of data to an astronaut while he performs specified tasks. A highly desirable aspect of this environment is to have the capability to rapidly develop and bring on-line a number of different displays for use in determining the best utilization of graphics techniques in achieving maximum efficiency of the test subject fulfilling his task. The Systems Engineering Simulator now has available a tool which assists in the rapid development of displays for these graphic workstations. The Display Builder was developed in-house to provide an environment which allows easy construction and modification of displays within minutes of receiving requirements for specific tests.

KSC-04PD-0277

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. U.S. Senator Bill Nelson (left foreground) and NASA Administrator Sean OKeefe (right) look deep in conversation as they leave the Central Florida Research Park, near Orlando. Behind Nelson is Congressman Tom Feeney and Center Director Jim Kennedy. The research park is being proposed as the location for NASAs new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASAs payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

KSC-04PD-0278

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. U.S. Senator Bill Nelson (left front) and NASA Administrator Sean OKeefe (right front) leave the Central Florida Research Park, near Orlando. Behind Nelson (at left) is Congressman Tom Feeney. The research park is being proposed as the location for NASAs new Shared Services Center. Six sites around the U.S. are under consideration for location of the Center, which would centralize NASAs payroll, accounting, human resources, facilities and procurement offices that are now handled at each field center. The consolidation is part of the One NASA focus. Others attending the presentation included U.S. Representative Ric Keller, Congressman Dave Weldon, Center Director Jim Kennedy and Pamella J. Dana, Ph.D., director, Office of Tourism, Trade, and Economic Development in Florida.

INFINITY ribbon-cutting

NASA Image and Video Library

2012-04-11

Stennis Space Center welcomes participants during ribbon-cutting activities for the INFINITY at NASA Stennis Space Center facility April 11, 2012. The visitor center and museum is located on Interstate 10, Exit 2, in south Mississippi.

A Probabilistic, Facility-Centric Approach to Lightning Strike Location

NASA Technical Reports Server (NTRS)

Huddleston, Lisa L.; Roeder, William p.; Merceret, Francis J.

2012-01-01

A new probabilistic facility-centric approach to lightning strike location has been developed. This process uses the bivariate Gaussian distribution of probability density provided by the current lightning location error ellipse for the most likely location of a lightning stroke and integrates it to determine the probability that the stroke is inside any specified radius of any location, even if that location is not centered on or even with the location error ellipse. This technique is adapted from a method of calculating the probability of debris collisionith spacecraft. Such a technique is important in spaceport processing activities because it allows engineers to quantify the risk of induced current damage to critical electronics due to nearby lightning strokes. This technique was tested extensively and is now in use by space launch organizations at Kennedy Space Center and Cape Canaveral Air Force Station. Future applications could include forensic meteorology.

Object-centered representations support flexible exogenous visual attention across translation and reflection.

PubMed

Lin, Zhicheng

2013-11-01

Visual attention can be deployed to stimuli based on our willful, top-down goal (endogenous attention) or on their intrinsic saliency against the background (exogenous attention). Flexibility is thought to be a hallmark of endogenous attention, whereas decades of research show that exogenous attention is attracted to the retinotopic locations of the salient stimuli. However, to the extent that salient stimuli in the natural environment usually form specific spatial relations with the surrounding context and are dynamic, exogenous attention, to be adaptive, should embrace these structural regularities. Here we test a non-retinotopic, object-centered mechanism in exogenous attention, in which exogenous attention is dynamically attracted to a relative, object-centered location. Using a moving frame configuration, we presented two frames in succession, forming either apparent translational motion or in mirror reflection, with a completely uninformative, transient cue presented at one of the item locations in the first frame. Despite that the cue is presented in a spatially separate frame, in both translation and mirror reflection, behavioralperformance in visual search is enhanced when the target in the second frame appears at the same relative location as the cue location than at other locations. These results provide unambiguous evidence for non-retinotopic exogenous attention and further reveal an object-centered mechanism supporting flexible exogenous attention. Moreover, attentional generalization across mirror reflection may constitute an attentional correlate of perceptual generalization across lateral mirror images, supporting an adaptive, functional account of mirror images confusion. Copyright © 2013 Elsevier B.V. All rights reserved.

Object-centered representations support flexible exogenous visual attention across translation and reflection

PubMed Central

Lin, Zhicheng

2013-01-01

Visual attention can be deployed to stimuli based on our willful, top-down goal (endogenous attention) or on their intrinsic saliency against the background (exogenous attention). Flexibility is thought to be a hallmark of endogenous attention, whereas decades of research show that exogenous attention is attracted to the retinotopic locations of the salient stimuli. However, to the extent that salient stimuli in the natural environment usually form specific spatial relations with the surrounding context and are dynamic, exogenous attention, to be adaptive, should embrace these structural regularities. Here we test a non-retinotopic, object-centered mechanism in exogenous attention, in which exogenous attention is dynamically attracted to a relative, object-centered location. Using a moving frame configuration, we presented two frames in succession, forming either apparent translational motion or in mirror reflection, with a completely uninformative, transient cue presented at one of the item locations in the first frame. Despite that the cue is presented in a spatially separate frame, in both translation and mirror reflection, human performance in visual search is enhanced when the target in the second frame appears at the same relative location as the cue location than at other locations. These results provide unambiguous evidence for non-retinotopic exogenous attention and further reveal an object-centered mechanism supporting flexible exogenous attention. Moreover, attentional generalization across mirror reflection may constitute an attentional correlate of perceptual generalization across lateral mirror images, supporting an adaptive, functional account of mirror images confusion. PMID:23942348

The new emergency structure of the Istituto Nazionale di Geofisica e Vulcanologia during the L’Aquila 2009 seismic sequence: the contribution of the COES (Seismological Emergency Operation Center - Centro Operativo Emergenza Sismica)

NASA Astrophysics Data System (ADS)

Moretti, M.; Govoni, A.; Nostro, C.; La Longa, F.; Crescimbene, M.; Pignone, M.; Selvaggi, G.; Working Group, C.

2009-12-01

The Centro Nazionale Terremoti (CNT - National Earthquake Center), departement of Istituto Nazionale di Geofisica e Vulcanologia (INGV), has designed and setup a rapid response emergency structure to face the occurrence of strong earthquakes. This structure is composed by a real time satellite telemetered temporary seismic network (see Abruzzese et al., 2009 Fall AGU) used to improve the hypocentral locations of the INGV National Seismic Network, a stand alone temporary seismic network whose goal is primarily the high dynamic/high resolution data acquisition in the epicentral area and a mobile operational center, the COES (Centro Operativo Emergenza Sismica, Seismological Emergency Operational Center). The COES structure is a sort of mobile office equipped with satellite internet communication that can be rapidly installed in the disaster area to support all the INGV staff operative needs and to cooperate with the Civil Protection department (DPC) aggregating all the scientific information available on the seismic sequence and providing updated information to Civil Protection for the decision making stage during the emergency. The structure is equipped with a heavy load trolley that carries a 6x6 inflatable tent, a satellite router, an UPS, computers, monitors and furniture. The facility can be installed in a couple of hours in the epicentral area and provides a full featured office with dedicated internet connection and VPN access to the INGV data management center in Rome. Just after the April 6 2009 Mw 6.3 earthquake in L’Aquila (Central Italy) the COES has been installed upon request of the Italian Civil Protection (DPC) in the DICOMAC (Directorate of Command and Control - which is the central structure of the DPC that coordinates the emergency activities in the areas affected by the earthquake) located in the Guardia di Finanza headquarters in Coppito nearby L'Aquila (the same location that hosted the G8 meeting). The COES produces real time reports on the seismic sequence evolution constituted by a detailed sequence map, histograms showing the evolution of the magnitude and the number of earthquakes in time and a daily event list. Moreover, it is possible to see the real time hypocentral locations using “SISMAP” (Doumaz et al., 2008), the same tool used in the Seismic Monitoring Center in Rome. During the emergency the COES has been also a reference information point for all people involved in the crisis management and has provided also psychological support to the rescuers and to the earthquake affected population. This education and outreach activity has proved to be extremely effective. References Abruzzese L. et al., AGU Fall Meeting 2009. Doumaz F. et al., Geomedia, speciale geologia, pp. 10-13, 2008.

Autonomous robot for detecting subsurface voids and tunnels using microgravity

NASA Astrophysics Data System (ADS)

Wilson, Stacy S.; Crawford, Nicholas C.; Croft, Leigh Ann; Howard, Michael; Miller, Stephen; Rippy, Thomas

2006-05-01

Tunnels have been used to evade security of defensive positions both during times of war and peace for hundreds of years. Tunnels are presently being built under the Mexican Border by drug smugglers and possibly terrorists. Several have been discovered at the border crossing at Nogales near Tucson, Arizona, along with others at other border towns. During this war on terror, tunnels under the Mexican Border pose a significant threat for the security of the United States. It is also possible that terrorists will attempt to tunnel under strategic buildings and possibly discharge explosives. The Center for Cave and Karst Study (CCKS) at Western Kentucky University has a long and successful history of determining the location of caves and subsurface voids using microgravity technology. Currently, the CCKS is developing a remotely controlled robot which will be used to locate voids underground. The robot will be a remotely controlled vehicle that will use microgravity and GPS to accurately detect and measure voids below the surface. It is hoped that this robot will also be used in military applications to locate other types of voids underground such as tunnels and bunkers. It is anticipated that the robot will be able to function up to a mile from the operator. This paper will describe the construction of the robot and the use of microgravity technology to locate subsurface voids with the robot.

75 FR 49526 - Freescale Semiconductor, Inc., Technical Information Center, Tempe, AZ; Freescale Semiconductor...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-13

... Semiconductor, Inc., Technical Information Center, Tempe, AZ; Freescale Semiconductor, Inc., Technical... October 1, 2009, applicable to workers of Freescale Semiconductor, Inc., Technical Information Center..., Massachusetts location of Freescale Semiconductor, Inc., Technical Information Center. The intent of the...

Italy INAF Data Center Report

NASA Technical Reports Server (NTRS)

Negusini, M.; Sarti, P.

2013-01-01

This report summarizes the activities of the Italian INAF VLBI Data Center. Our Data Center is located in Bologna, Italy and belongs to the Institute of Radioastronomy, which is part of the National Institute of Astrophysics.

The New Cloud Absorption Radiometer (CAR) Software: One Model for NASA Remote Sensing Virtual Instruments

NASA Technical Reports Server (NTRS)

Roth, Don J.; Rapchun, David A.; Jones, Hollis H.

2001-01-01

The Cloud Absorption Radiometer (CAR) instrument has been the most frequently used airborne instrument built in-house at NASA Goddard Space Flight Center, having flown scientific research missions on-board various aircraft to many locations in the United States, Azores, Brazil, and Kuwait since 1983. The CAR instrument is capable of measuring scattered light by clouds in fourteen spectral bands in UV, visible and near-infrared region. This document describes the control, data acquisition, display, and file storage software for the new version of CAR. This software completely replaces the prior CAR Data System and Control Panel with a compact and robust virtual instrument computer interface. Additionally, the instrument is now usable for the first time for taking data in an off-aircraft mode. The new instrument is controlled via a LabVIEW v5. 1.1-developed software interface that utilizes, (1) serial port writes to write commands to the controller module of the instrument, and (2) serial port reads to acquire data from the controller module of the instrument. Step-by-step operational procedures are provided in this document. A suite of other software programs has been developed to complement the actual CAR virtual instrument. These programs include: (1) a simulator mode that allows pretesting of new features that might be added in the future, as well as demonstrations to CAR customers, and development at times when the instrument/hardware is off-location, and (2) a post-experiment data viewer that can be used to view all segments of individual data cycles and to locate positions where 'start' and stop' byte sequences were incorrectly formulated by the instrument controller. The CAR software described here is expected to be the basis for CAR operation for many missions and many years to come.

Localization of virtual sound at 4 Gz.

PubMed

Sandor, Patrick M B; McAnally, Ken I; Pellieux, Lionel; Martin, Russell L

2005-02-01

Acceleration directed along the body's z-axis (Gz) leads to misperception of the elevation of visual objects (the "elevator illusion"), most probably as a result of errors in the transformation from eye-centered to head-centered coordinates. We have investigated whether the location of sound sources is misperceived under increased Gz. Visually guided localization responses were made, using a remotely controlled laser pointer, to virtual auditory targets under conditions of 1 and 4 Gz induced in a human centrifuge. As these responses would be expected to be affected by the elevator illusion, we also measured the effect of Gz on the accuracy with which subjects could point to the horizon. Horizon judgments were lower at 4 Gz than at 1 Gz, so sound localization responses at 4 Gz were corrected for this error in the transformation from eye-centered to head-centered coordinates. We found that the accuracy and bias of sound localization are not significantly affected by increased Gz. The auditory modality is likely to provide a reliable means of conveying spatial information to operators in dynamic environments in which Gz can vary.

Preliminary research of a novel center-driven robot for upper extremity rehabilitation.

PubMed

Cao, Wujing; Zhang, Fei; Yu, Hongliu; Hu, Bingshan; Meng, Qiaoling

2018-01-19

Loss of upper limb function often appears after stroke. Robot-assisted systems are becoming increasingly common in upper extremity rehabilitation. Rehabilitation robot provides intensive motor therapy, which can be performed in a repetitive, accurate and controllable manner. This study aims to propose a novel center-driven robot for upper extremity rehabilitation. A new power transmission mechanism is designed to transfer the power to elbow and shoulder joints from three motors located on the base. The forward and inverse kinematics equations of the center-driven robot (CENTROBOT) are deduced separately. The theoretical values of the scope of joint movements are obtained with the Denavit-Hartenberg parameters method. A prototype of the CENTROBOT is developed and tested. The elbow flexion/extension, shoulder flexion/extension and shoulder adduction/abduction can be realized of the center-driven robot. The angles value of joints are in conformity with the theoretical value. The CENTROBOT reduces the overall size of the robot arm, the influence of motor noise, radiation and other adverse factors by setting all motors on the base. It can satisfy the requirements of power and movement transmission of the robot arm.

A magnetic damper for first mode vibration reduction in multimass flexible rotors

NASA Technical Reports Server (NTRS)

Kasarda, M. E. F.; Allaire, P. E.; Humphris, R. R.; Barrett, L. E.

1989-01-01

Many rotating machines such as compressors, turbines and pumps have long thin shafts with resulting vibration problems, and would benefit from additional damping near the center of the shaft. Magnetic dampers have the potential to be employed in these machines because they can operate in the working fluid environment unlike conventional bearings. An experimental test rig is described which was set up with a long thin shaft and several masses to represent a flexible shaft machine. An active magnetic damper was placed in three locations: near the midspan, near one end disk, and close to the bearing. With typical control parameter settings, the midspan location reduced the first mode vibration 82 percent, the disk location reduced it 75 percent and the bearing location attained a 74 percent reduction. Magnetic damper stiffness and damping values used to obtain these reductions were only a few percent of the bearing stiffness and damping values. A theoretical model of both the rotor and the damper was developed and compared to the measured results. The agreement was good.

New sonic shockwave multi-element sensors mounted on a small airfoil flown on F-15B testbed aircraft

NASA Technical Reports Server (NTRS)

1996-01-01

An experimental device to pinpoint the location of a shockwave that develops in an aircraft flying at transonic and supersonic speeds was recently flight-tested at NASA's Dryden Flight Research Center, Edwards, California. The shock location sensor, developed by TAO Systems, Hampton, Va., utilizes a multi-element hot-film sensor array along with a constant-voltage anemometer and special diagnostic software to pinpoint the exact location of the shockwave and its characteristics as it develops on an aircraft surface. For this experiment, the 45-element sensor was mounted on the small Dryden-designed airfoil shown in this illustration. The airfoil was attached to the Flight Test Fixture mounted underneath the fuselage of Dryden's F-15B testbed aircraft. Tests were flown at transonic speeds of Mach 0.7 to 0.9, and the device isolated the location of the shock wave to within a half-inch. Application of this technology could assist designers of future supersonic aircraft in improving the efficiency of engine air inlets by controlling the shockwave, with a related improvement in aircraft performance and fuel economy.

Spatial balance of color triads in the abstract art of Piet Mondrian.

PubMed

Locher, Paul; Overbeeke, Kees; Stappers, Pieter Jan

2005-01-01

We examined the interactive contribution of the color and size of the three areas occupied by the primary colors red, yellow, and blue in adaptations of abstract compositions by Mondrian to the perceived weight of the areas and the location of the balance centers of the compositions. Thirty-six art stimuli were created by experimentally changing the colors in the three areas of six original works so that the resulting five variations and the original constituted the six possible spatial arrangements of the three colors in the three locations. In experiment 1, design-trained and untrained participants determined the location of the balance center of each composition seen on a computer screen and rated the apparent weight or heaviness of each color area. In experiment 2, untrained participants determined the location of the balance centers of the compositions when projected to their actual size. It was found that, for both trained and untrained participants, the perceived weight of a color, especially red and yellow, varied as a function of the size of the area it occupied. Furthermore, participants in both experiments perceived shifts in the locations of the balance centers between the originals and their altered versions. Only the trained participants, however, perceived significant shifts in balance centers among the five variations of the compositions, demonstrating their superior sensitivity to the contribution of color to balance structure. Taken together, the findings demonstrate the existence of a color-area-weight relationship among color triads in abstract displays and the influence of this relationship on color balance in abstract compositions.

A Virtual Mission Operations Center: Collaborative Environment

NASA Technical Reports Server (NTRS)

Medina, Barbara; Bussman, Marie; Obenschain, Arthur F. (Technical Monitor)

2002-01-01

The Virtual Mission Operations Center - Collaborative Environment (VMOC-CE) intent is to have a central access point for all the resources used in a collaborative mission operations environment to assist mission operators in communicating on-site and off-site in the investigation and resolution of anomalies. It is a framework that as a minimum incorporates online chat, realtime file sharing and remote application sharing components in one central location. The use of a collaborative environment in mission operations opens up the possibilities for a central framework for other project members to access and interact with mission operations staff remotely. The goal of the Virtual Mission Operations Center (VMOC) Project is to identify, develop, and infuse technology to enable mission control by on-call personnel in geographically dispersed locations. In order to achieve this goal, the following capabilities are needed: Autonomous mission control systems Automated systems to contact on-call personnel Synthesis and presentation of mission control status and history information Desktop tools for data and situation analysis Secure mechanism for remote collaboration commanding Collaborative environment for remote cooperative work The VMOC-CE is a collaborative environment that facilitates remote cooperative work. It is an application instance of the Virtual System Design Environment (VSDE), developed by NASA Goddard Space Flight Center's (GSFC) Systems Engineering Services & Advanced Concepts (SESAC) Branch. The VSDE is a web-based portal that includes a knowledge repository and collaborative environment to serve science and engineering teams in product development. It is a "one stop shop" for product design, providing users real-time access to product development data, engineering and management tools, and relevant design specifications and resources through the Internet. The initial focus of the VSDE has been to serve teams working in the early portion of the system/product lifecycle - concept development, proposal preparation, and formulation. The VMOC-CE expands the application of the VSDE into the operations portion of the system lifecycle. It will enable meaningful and real-time collaboration regardless of the geographical distribution of project team members. Team members will be able to interact in satellite operations, specifically for resolving anomalies, through access to a desktop computer and the Internet. Mission Operations Management will be able to participate and monitor up to the minute status of anomalies or other mission operations issues. In this paper we present the VMOC-CE project, system capabilities, and technologies.

Hole-Center Locating Tool

NASA Technical Reports Server (NTRS)

Senter, H. F.

1984-01-01

Tool alines center of new hold with existing hole. Tool marks center of new hole drilled while workpiece is in place. Secured with bolts while hole center marked with punch. Used for field installations where reference points unavailable or work area cramped and not easily accessible with conventional tools.

14 CFR 1206.400 - Information Centers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Information Centers. 1206.400 Section 1206... TO MEMBERS OF THE PUBLIC Location for Inspection and Request of Agency Records § 1206.400 Information Centers. NASA will maintain Information Centers as set forth in this subpart. ...

Research on reverse logistics location under uncertainty environment based on grey prediction

NASA Astrophysics Data System (ADS)

Zhenqiang, Bao; Congwei, Zhu; Yuqin, Zhao; Quanke, Pan

This article constructs reverse logistic network based on uncertain environment, integrates the reverse logistics network and distribution network, and forms a closed network. An optimization model based on cost is established to help intermediate center, manufacturing center and remanufacturing center make location decision. A gray model GM (1, 1) is used to predict the product holdings of the collection points, and then prediction results are carried into the cost optimization model and a solution is got. Finally, an example is given to verify the effectiveness and feasibility of the model.

Implementation of Information Management System for Radiation Safety of Personnel at the Russian Northwest Center for Radioactive Waste Management 'SevRAO' - 13131

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chizhov, K.; Simakov, A.; Seregin, V.

2013-07-01

The report is an overview of the information-analytical system designed to assure radiation safety of workers. The system was implemented in the Northwest Radioactive Waste Management Center 'SevRAO' (which is a branch of the Federal State Unitary Enterprise 'Radioactive Waste Management Enterprise RosRAO'). The center is located in the Northwest Russia. In respect to 'SevRAO', the Federal Medical-Biological Agency is the regulatory body, which deals with issues of radiation control. The main document to regulate radiation control is 'Reference levels of radiation factors in radioactive wastes management center'. This document contains about 250 parameters. We have developed a software toolmore » to simplify control of these parameters. The software includes: input interface, the database, dose calculating module and analytical block. Input interface is used to enter radiation environment data. Dose calculating module calculates the dose on the route. Analytical block optimizes and analyzes radiation situation maps. Much attention is paid to the GUI and graphical representation of results. The operator can enter the route at the industrial site or watch the fluctuations of the dose rate field on the map. Most of the results are presented in a visual form. Here we present some analytical tasks, such as comparison of the dose rate in some point with control levels at this point, to be solved for the purpose of radiation safety control. The program helps to identify points making the largest contribution to the collective dose of the personnel. The tool can automatically calculate the route with the lowest dose, compare and choose the best route. The program uses several options to visualize the radiation environment at the industrial site. This system will be useful for radiation monitoring services during the operation, planning of works and development of scenarios. The paper presents some applications of this system on real data over three years - from March 2009 to February 2012. (authors)« less

KENNEDY SPACE CENTER, FLA. - Workers calibrate a tracking telescope, part of the Distant Object Attitude Measurement System (DOAMS), located in Cocoa Beach, Fla. The telescope provides optical support for launches from KSC and Cape Canaveral.

NASA Image and Video Library

2003-09-03

KENNEDY SPACE CENTER, FLA. - Workers calibrate a tracking telescope, part of the Distant Object Attitude Measurement System (DOAMS), located in Cocoa Beach, Fla. The telescope provides optical support for launches from KSC and Cape Canaveral.

About High-Performance Computing at NREL | High-Performance Computing |

Science.gov Websites

Day(s): First Thursday of every month Hours: 11 a.m. - 12 p.m. Location: ESIF B211-Edison Conference Room Contact: Jennifer Southerland Insight Center - Visualization Tools Day(s): Every Monday Hours: 10 Data System Day(s): Every Monday Hours: 10 a.m. - 11 a.m. Location: ESIF B308-Insight Center

75 FR 59310 - Self-Regulatory Organizations; New York Stock Exchange LLC; Order Approving a Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-27

... same order gateway regardless of whether the sender is co-located in the Exchange's data center or not... for co-location services. The proposed rule change was published for comment in the Federal Register... it planned to begin operating a data center in Mahwah, New Jersey, from which it will offer co...

75 FR 14644 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing of Proposed Rule Change Amending...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-26

... Items have been prepared by the self-regulatory organization. The Commission is publishing this notice... currently offers co-location services at a data center operated by a private third party vendor located in New Jersey. The Exchange offers space at the data center ranging from half cabinets up to two full...

Location and Venue | The Metastatic Niche: Models, Mechanisms and Targeting Targets into Therapeutics

Cancer.gov

Location and Venue **EVENT CHANGE OF LOCATION:  **Building 10 (Clinical Center) - Masur Auditorium** Helpful links to locate the Masur Auditorium on the NIH campus:  https://www.ors.od.nih.gov/maps/Pages/NIH-Visitor-Map.aspx