40 CFR 63.1544 - Standards for fugitive dust sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... according to, a standard operating procedures manual that describes in detail the measures that will be put... (c) of this section, the standard operating procedures manual shall be submitted to the Administrator... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Standards for fugitive dust sources. 63...

40 CFR 63.1544 - Standards for fugitive dust sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... according to, a standard operating procedures manual that describes in detail the measures that will be put... (c) of this section, the standard operating procedures manual shall be submitted to the Administrator... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Standards for fugitive dust sources. 63...

Dust control products at Hagerman National Wildlife Refuge, Texas: environmental safety and performance

USGS Publications Warehouse

Kunz, Bethany K.; Little, Edward E.

2015-01-01

Controlling fugitive dust while protecting natural resources is a challenge faced by all managers of unpaved roads. Unfortunately, road managers choosing between dust control products often have little objective environmental information to aid their decisions. To address this information gap, the U.S. Geological Survey and the U.S. Fish and Wildlife Service collaborated on a field test of three dust control products with the objectives of (a) evaluating product performance under real-world conditions, (b) verifying the environmental safety of products identified as practically nontoxic in laboratory tests, and (c) testing the feasibility of several environmental monitoring techniques for use in dust control tests. In cooperation with refuge staff and product vendors, three products (one magnesium chloride plus binder, one cellulose, and one synthetic fluid plus binder) were applied in July 2012 to replicated road sections at the Hagerman National Wildlife Refuge in Texas. These sections were monitored periodically for 12 months after application. Product performance was assessed by mobile-mounted particulate-matter meters measuring production of fugitive dust and by observations of road conditions. Environmental safety was evaluated through on-site biological observations and leaching tests with samples of treated aggregate. All products reduced dust and improved surface condition during those 12 months. Planned environmental measurements were not always compatible with day-to-day refuge management actions; this incompatibility highlighted the need for flexible biological monitoring plans. As one of the first field tests of dust suppressants that explicitly incorporated biological endpoints, this effort provides valuable information for improving field tests and for developing laboratory or semifield alternatives.

DEPOSITION AND REMOVAL OF FUGITIVE DUST IN THE ARID SOUTHWESTERN UNITED STATES: MEASUREMENTS AND MODEL RESULTS

EPA Science Inventory

This work was motivated by the need to better reconcile emission factors for fugitive dust with the amount of geologic material found on ambient filter samples. The deposition of particulate matter with aerodynamic diameter less than or equal to 10 µm (PM₁₀), generated...

Preliminary assessment of an economical fugitive road dust sampler for the collection of bulk samples for geochemical analysis.

PubMed

Witt, Emitt C; Wronkiewicz, David J; Shi, Honglan

2013-01-01

Fugitive road dust collection for chemical analysis and interpretation has been limited by the quantity and representativeness of samples. Traditional methods of fugitive dust collection generally focus on point-collections that limit data interpretation to a small area or require the investigator to make gross assumptions about the origin of the sample collected. These collection methods often produce a limited quantity of sample that may hinder efforts to characterize the samples by multiple geochemical techniques, preserve a reference archive, and provide a spatially integrated characterization of the road dust health hazard. To achieve a "better sampling" for fugitive road dust studies, a cyclonic fugitive dust (CFD) sampler was constructed and tested. Through repeated and identical sample collection routes at two collection heights (50.8 and 88.9 cm above the road surface), the products of the CFD sampler were characterized using particle size and chemical analysis. The average particle size collected by the cyclone was 17.9 μm, whereas particles collected by a secondary filter were 0.625 μm. No significant difference was observed between the two sample heights tested and duplicates collected at the same height; however, greater sample quantity was achieved at 50.8 cm above the road surface than at 88.9 cm. The cyclone effectively removed 94% of the particles >1 μm, which substantially reduced the loading on the secondary filter used to collect the finer particles; therefore, suction is maintained for longer periods of time, allowing for an average sample collection rate of about 2 g mi. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Source apportionment of size-fractionated particles during the 2013 Asian Youth Games and the 2014 Youth Olympic Games in Nanjing, China.

PubMed

Chen, Pulong; Wang, Tijian; Lu, Xiaobo; Yu, Yiyong; Kasoar, Matthew; Xie, Min; Zhuang, Bingliang

2017-02-01

In this study, samples of size-fractionated particulate matter were collected continuously using a 9-size interval cascade impactor at an urban site in Nanjing, before, during and after the Asian Youth Games (AYG), from July to September of 2013, and the Youth Olympic Games (YOG), from July to September of 2014. First, elemental concentrations, water-soluble ions including Cl - , NO 3 - , SO 4 2- , NH 4 + , K + , Na + and Ca 2+ , organic carbon (OC) and elemental carbon (EC) were analysed. Then, the source apportionment of the fine and coarse particulate matter was carried out using the chemical mass balance (CMB) model. The average PM 10 concentrations were 90.4±20.0μg/m 3 during the 2013 AYG and 70.6±25.3μg/m 3 during the 2014 YOG. For PM 2.1, the average concentrations were 50.0±12.8μg/m 3 in 2013 and 34.6±17.0μg/m 3 in 2014. Investigations showed that the average concentrations of particles declined significantly from 2013 to 2014, and concentrations were at the lowest levels during the events. Results indicated that OC, EC, sulfate and crustal elements have significant monthly and size-based variations. The major components, including crustal elements, water-soluble ions and carbonaceous aerosol accounted for 75.3-91.9% of the total particulate mass concentrations during the sampling periods. Fugitive dust, coal combustion dust, iron dust, construction dust, soil dust, vehicle exhaust, secondary aerosols and sea salt have been classified as the main emissions in Nanjing. The source apportionment results indicate that the emissions from fugitive dust, which was the most abundance emission source during the 2013 AYG, contributed to 23.0% of the total particle mass. However, fugitive dust decreased to 6.2% of the total particle mass during the 2014 YOG. Construction dust (14.7% versus 7.8% for the AYG and the YOG, respectively) and secondary sulfate aerosol (9.3% versus 8.0% for the AYG and the YOG, respectively) showed the same trend as fugitive dust, suggesting that the mitigation measures of controlling particles from the paved roads, construction and industry worked more efficiently during the YOG. Copyright © 2016 Elsevier B.V. All rights reserved.

40 CFR 63.1544 - Standards for fugitive dust sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... associated air pollution control equipment and monitoring equipment, in a manner consistent with safety and good air pollution control practices for minimizing emissions. Determination of whether such operation.... 63.1544 Section 63.1544 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.1544 - Standards for fugitive dust sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... associated air pollution control equipment and monitoring equipment, in a manner consistent with safety and good air pollution control practices for minimizing emissions. Determination of whether such operation.... 63.1544 Section 63.1544 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.1544 - Standards for fugitive dust sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... associated air pollution control equipment and monitoring equipment, in a manner consistent with safety and good air pollution control practices for minimizing emissions. Determination of whether such operation....1544 Section 63.1544 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...

Contribution of Fugitive Emissions for PM10 Concentrations in an Industrial Area of Portugal

NASA Astrophysics Data System (ADS)

Marta Almeida, Susana; Viana Silva, Alexandra; Garcia, Silvia; Miranda, Ana Isabel

2013-04-01

Significant atmospheric dust arises from the mechanical disturbance of granular material exposed to the air. Dust generated from these open sources is termed "fugitive" because it is not discharged to the atmosphere in a confined flow stream. Common sources of fugitive dust include unpaved roads, agricultural tilling operations, aggregate storage piles, heavy construction and harbor operations. The objective of this work was to identify the likeliness and extend of the PM10 limit value exceedences due to fugitive emissions in a particularly zone where PM fugitive emissions are a core of environmental concerns - Mitrena, Portugal. Mitrena, is an industrial area that coexists with a high-density urban region (Setúbal) and areas with an important environmental concern (Sado Estuary and Arrábida which belongs to the protected area Natura 2000 Network). Due to the typology of industry sited in Mitrena (e.g. power plant, paper mill, cement, pesticides and fertilized productions), there are a large uncontrolled PM fugitive emissions, providing from heavy traffic and handling and storage of raw material on uncover stockyards in the harbor and industries. Dispersion modeling was performed with the software TAPM (The Air Pollution Model) and results were mapped over the study area, using GIS (Geographic Information Systems). Results showed that managing local particles concentrations can be a frustrating affair because the weight of fugitive sources is very high comparing with the local anthropogenic stationary sources. In order to ensure that the industry can continue to meet its commitments in protecting air quality, it is essential to warrant that the characteristics of releases from all fugitive sources are fully understood in order to target future investments in those areas where maximum benefit will be achieved.

40 CFR 52.470 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 44431 Section 604 Open Burning 3/15/85 8/28/95, 60 FR 44431 Section 605 Control of Fugitive Dust 3/15/85... 26Civil Fines for Moving and Non-Moving Violations Section 2600.1 Infraction: Inspection, Registration...

40 CFR 52.470 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 44431 Section 604 Open Burning 3/15/85 8/28/95, 60 FR 44431 Section 605 Control of Fugitive Dust 3/15/85... 26Civil Fines for Moving and Non-Moving Violations Section 2600.1 Infraction: Inspection, Registration...

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan.

PubMed

Chang, Chang-Tang; Chang, Yu-Min; Lin, Wen-Yinn; Wu, Ming-Ching

2010-10-01

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.

78 FR 922 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-07

... ) emissions from sources of fugitive dust such as unpaved roads and disturbed soils in open and agricultural... trespass and stabilize disturbed soil on open areas larger than 0.5 acres in urban areas, and larger than...

40 CFR 63.549 - Notification requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... shall submit the fugitive dust control standard operating procedures manual required under § 63.545(a) and the standard operating procedures manual for baghouses required under § 63.548(a) to the... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

40 CFR 63.549 - Notification requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... shall submit the fugitive dust control standard operating procedures manual required under § 63.545(a) and the standard operating procedures manual for baghouses required under § 63.548(a) to the... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

Fugitive Dust Emission Factors for Puff and Mobile Military Sources Measured by Micro-pulse Lidar - A Summary of Results

NASA Astrophysics Data System (ADS)

Yuen, W.; Du, K.; Rood, M. J.; Kemme, M. R.; Kim, B.; Hashmonay, R. A.

2010-12-01

A summary of the development of a novel optical remote sensing (ORS) method that determined fugitive dust emission factors for unique military activities is described for puff and mobile sources. Four field campaigns characterized artillery back blasts as puff sources (M549A1 and M107), and movement of military vehicles (M1A1, M113, Bradley Fighting Vehicle (BFV), M88, M270, M577, and HEMTT) and an airborne helicopter (Bell 210) as mobile sources. The ORS method includes a Micro-Pulse Lidar (MPL) and a reflective target that determines one-dimensional (1-D) light extinction coefficient profiles. The MPL was mounted on a positioner that allows the MPL to automatically scan vertically, which allowed 1-D extinction coefficient profiles to be measured at select angles from horizontal. Two-dimensional (2-D) light extinction coefficient profiles were then determined by interpolating the 1-D extinction profiles measured at select angles. Dust property, in the form of the mass extinction efficiency (MEE), was measured using Open Path- Fourier Transform Infrared Spectrometry (OP-FTIR) and Open Path- Laser Transmissometry (OP-LT) in the first three field campaigns and an OP-LT and DustTrak™ in the fourth field campaign. MEE was used to convert the 2-D light extinction coefficient profiles to 2-D dust mass concentration profiles. Emission factors were determined by integrating the 2-D mass concentration profiles with measured wind vectors. Results from these field campaigns show that: 1) artillery with stronger recoiling forces generates more fugitive dust; 2) the dust emission factors for tracked vehicles are correlated with vehicle momentum; 3) emission factor decreases with increasing speed for airborne helicopters; and 4) wheeled vehicles (HEMTT) generate more fugitive dust than tracked vehicles (M88, M270, M577).

Ensemble classification for identifying neighbourhood sources of fugitive dust and associations with observed PM10

NASA Astrophysics Data System (ADS)

Khuluse-Makhanya, Sibusisiwe; Stein, Alfred; Breytenbach, André; Gxumisa, Athi; Dudeni-Tlhone, Nontembeko; Debba, Pravesh

2017-10-01

In urban areas the deterioration of air quality as a result of fugitive dust receives less attention than the more prominent traffic and industrial emissions. We assessed whether fugitive dust emission sources in the neighbourhood of an air quality monitor are predictors of ambient PM10 concentrations on days characterized by strong local winds. An ensemble maximum likelihood method is developed for land cover mapping in the vicinity of an air quality station using SPOT 6 multi-spectral images. The ensemble maximum likelihood classifier is developed through multiple training iterations for improved accuracy of the bare soil class. Five primary land cover classes are considered, namely built-up areas, vegetation, bare soil, water and 'mixed bare soil' which denotes areas where soil is mixed with either vegetation or synthetic materials. Preliminary validation of the ensemble classifier for the bare soil class results in an accuracy range of 65-98%. Final validation of all classes results in an overall accuracy of 78%. Next, cluster analysis and a varying intercepts regression model are used to assess the statistical association between land cover, a fugitive dust emissions proxy and observed PM10. We found that land cover patterns in the neighbourhood of an air quality station are significant predictors of observed average PM10 concentrations on days when wind speeds are conducive for dust emissions. This study concludes that in the absence of an emissions inventory for ambient particulate matter, PM10 emitted from dust reservoirs can be statistically accounted for by land cover characteristics. This supports the use of land cover data for improved prediction of PM10 at locations without air quality monitoring stations.

40 CFR 63.1548 - Notification requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... submit the fugitive dust control standard operating procedures manual required under § 63.1544(a) and the standard operating procedures manual for baghouses required under § 63.1547(a) to the Administrator or... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

40 CFR 63.1548 - Notification requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... submit the fugitive dust control standard operating procedures manual required under § 63.1544(a) and the standard operating procedures manual for baghouses required under § 63.1547(a) to the Administrator or... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

40 CFR 63.1654 - Operational and work practice standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... according to a written fugitive dust control plan must be incorporated in the operating permit for the... standards. 63.1654 Section 63.1654 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.1654 - Operational and work practice standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... according to a written fugitive dust control plan must be incorporated in the operating permit for the... standards. 63.1654 Section 63.1654 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

Managing dust on unpaved roads and airports.

DOT National Transportation Integrated Search

2014-10-01

Fugitive dust emanating from vehicle traffic on unpaved roads and runways can have significant impacts on safety, health, quality of life, and the cost : of maintenance. Managing dust provides a means of reducing these impacts. Shearing forces create...

40 CFR 63.1654 - Operational and work practice standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... according to a written fugitive dust control plan must be incorporated in the operating permit for the... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Operational and work practice standards... PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR 63.545 - Standards for fugitive dust sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... according to a standard operating procedures manual that describes in detail the measures that will be put... standard operating procedures manual shall be submitted to the Administrator or delegated authority for review and approval. (c) The controls specified in the standard operating procedures manual shall at a...

40 CFR 63.545 - Standards for fugitive dust sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... according to a standard operating procedures manual that describes in detail the measures that will be put... standard operating procedures manual shall be submitted to the Administrator or delegated authority for review and approval. (c) The controls specified in the standard operating procedures manual shall at a...

The Atlantic Richfield Company Black Thunder mine haul road dust study. [Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maxwell, D.R.; Hormel, T.R.; Ives, J.A.

An examination of the effectiveness of various haul road dust control measures was performed at ARCO's Black Thunder Mine near Wright, Wyoming by evaluating both visible observations and quantitative measurements of particle concentrations. In order to evaluate dust control effectiveness both a 300 foot (91.5 meter) and 175 foot (53.4 meter) section of the main coal haul road was selected for testing. The test sections were separated by a 200 foot (61 meter) buffer zone. Each test section was relatively straight and away from interferences from other mine sources. The five haul road treatment test sequences evaluated for control measuremore » effectiveness were: an untreated road segment; water treatment two times per hour; water treatment four times per hour; previously chemically treated segment of haul road (ARCO 2400 dust suppressant); and testing after application of Coherex (10% dilution). By comparing uncontrolled situations with various controlled situations, an estimate of the control efficiency of the dust control measures was determined. Based upon the results of the study a fugitive dust control scheme was selected considering control effectiveness, economics and operational efficiency.« less

Investigation of fugitive dust emissions from nepheline syenite mine tailings near Nephton, Ontario

NASA Astrophysics Data System (ADS)

Ogungbemide, Damilare Immanuel

A set of experiments was designed to investigate the factors--atmospheric and surficial--controlling fugitive dust emissions from the tailings ponds of UNIMIN Canada, a mining company that extracts and produces nepheline syenite (feldspar) at two adjacent sites (Nephton and Blue Mountain) located north of Havelock, Ontario. Using wind tunnel measurements, the combined influence of relative humidity and temperature (represented by the absolute matric potential, |psi|) on dust emission was quantified and modeled. About 300 experimental runs were conducted under various conditions of wind speed (4.5-6.25 ms -1), temperature (0-30°C) and relative humidity (10-70%). Generally, dust flux decreased as a logarithmic function of matric potential, with dust emission strongly suppressed for RH > 60% or |psi|<70 MPa. Field measurements also confirmed the role of relative humidity in suppressing dust emission. Irrigation, which is widely used by mines to control dust emissions, reduced ambient dust concentration at the study site only about 60% of the time, with the highest mitigation efficiencies (average of 90%) occurring when the total depth of water applied intermittently over a few hours was greater than 10 mm. In the absence of emergent vegetation, the terrestrial laser scanning (TLS) technique proved to be a promising method for detecting and estimating both spatial and temporal moisture content changes in the field environment, particularly for the very thin surface layer, which is the most important layer for dust emission. It is hoped that the results from this study will help mines to optimize their dust management programs for the range of climate and topographic conditions found at their sites, and also serve as a source of useful information and input data for atmospheric dispersion models, such as AERMOD and CALPUFF, whose accuracy depends on the quality of the input data such as the emission rate.

Record of Decision for the First Air National Guard F-35A Operational Base

DTIC Science & Technology

2013-12-02

Air Quality • Employ fugitive dust control and soil retention practices including: - Water trucks or sprinkler systems to keep all areas of vehicle...with local fire departments on F-35A crash response procedures. Soils and Water • Sequence construction activities to limit the soil exposure for

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... limited to the following: (i) Use, where possible, of water or chemicals for control of dust in the...) Application of asphalt, oil (but not used oil), water, or other suitable chemicals on unpaved roads, materials... stockpiles in cases where application of oil, water, or chemicals is not sufficient or appropriate to prevent...

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... limited to the following: (i) Use, where possible, of water or chemicals for control of dust in the...) Application of asphalt, oil (but not used oil), water, or other suitable chemicals on unpaved roads, materials... stockpiles in cases where application of oil, water, or chemicals is not sufficient or appropriate to prevent...

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... limited to the following: (i) Use, where possible, of water or chemicals for control of dust in the...) Application of asphalt, oil (but not used oil), water, or other suitable chemicals on unpaved roads, materials... stockpiles in cases where application of oil, water, or chemicals is not sufficient or appropriate to prevent...

Field testing of fugitive dust control techniques at a uranium mill tailings pile - 1982 Field Test, Gas Hills, Wyoming.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elmore, M.R.; Hartley, J.N.

A field test was conducted on a uranium tailings pile to evaluate the effectiveness of 15 chemical stabilizers for control of fugitive dust from uranium mill tailings. A tailings pile at the Federal American Partners (FAP) Uranium Mill, Gas Hills, Wyoming, was used for the field test. Preliminary laboratory tests using a wing tunnel were conducted to select the more promising stabilizers for field testing. Fourteen of the chemical stabilizers were applied with a field spray system pulled behind a tractor; one--Hydro Mulch--was applied with a hydroseeder. A portable weather station and data logger were installed to record the weathermore » conditions at the test site. After 1 year of monitoring (including three site visits), all of the stabilizers have degraded to some degree; but those applied at the manufacturers' recommended rate are still somewhat effective in reducing fugitive emissions. The following synthetic polymer emulsions appear to be the more effective stabilizers: Wallpol 40-133 from Reichold Chemicals, SP-400 from Johnson and March Corporation, and CPB-12 from Wen Don Corporation. Installed costs for the test plots ranged from $8400 to $11,300/ha; this range results from differences in stabilizer costs. Large-scale stabilization costs of the test materials are expected to range from $680 to $3600/ha based on FAP experience. Evaluation of the chemical stabilizers will continue for approximately 1 year. 2 references, 33 figures, 22 tables.« less

EFFECT OF VEHICLE CHARACTERISTICS ON UNPAVED ROAD DUST EMISSIONS

EPA Science Inventory

This paper presents PM₁₀ fugitive dust emission factors for a range of vehicles types and examines the influence of vehicle and wake characteristics on the strength of emissions from an unpaved road.

A wood-strand material for wind erosion control: effects on total sediment loss, PM10 vertical flux, and PM10 loss.

PubMed

Copeland, N S; Sharratt, B S; Wu, J Q; Foltz, R B; Dooley, J H

2009-01-01

Fugitive dust from eroding land poses risks to environmental quality and human health, and thus, is regulated nationally based on ambient air quality standards for particulate matter with mean aerodynamic diameter < or = 10 microm (PM10) established in the Clean Air Act. Agricultural straw has been widely used for rainfall-induced erosion control; however, its performance for wind erosion mitigation has been less studied, in part because straw is mobile at moderate wind velocities. A wood-based long-strand material has been developed for rainfall-induced erosion control and has shown operational promise for control of wind-induced erosion and dust emissions from disturbed sites. The purpose of this study was to evaluate the efficacy of both agricultural straw and wood-strand materials in controlling wind erosion and fugitive dust emissions under laboratory conditions. Wind tunnel tests were conducted to compare wood strands of several geometries to agricultural wheat straw and bare soil in terms of total sediment loss, PM10 vertical flux, and PM10 loss. Results indicate that the types of wood strands tested are stable at wind speeds of up to 18 m s(-1), while wheat straw is only stable at speeds of up to 6.5 m s(-1). Wood strands reduced total sediment loss and PM10 emissions by 90% as compared to bare soil across the range of wind speeds tested. Wheat straw did not reduce total sediment loss for the range of speeds tested, but did reduce PM10 emissions by 75% compared to a bare soil at wind speeds of up to 11 m s(-1).

A wood-strand material for wind erosion control: effects on total sediment loss, PM10 vertical flux, and PM10 loss

Treesearch

N. S. Copeland; B. S. Sharratt; J. Q. Wu; R. B. Foltz; J. H. Dooley

2009-01-01

Fugitive dust from eroding land poses risks to environmental quality and human health, and thus, is regulated nationally based on ambient air quality standards for particulate matter with mean aerodynamic diameter ≤ 10 μm (PM10) established in the Clean Air Act. Agricultural straw has been widely used for rainfall-induced...

Comparison of conventional and bio-treated methods as dust suppressants.

PubMed

Naeimi, Maryam; Chu, Jian

2017-10-01

Dust is an environmental, geotechnical, health, and economical hazard. Fugitive dust emanating along transportation systems such as roads, railways, and airports especially can have significant impacts on health, safety, material loss, cost of maintenance, and interfere with the facilities. Quantitative studies on the effectiveness of the proper dust palliatives and their environmental impact have been studied with a number of biological and chemical methods. The objective of this study was to establish a method for using the microbial Induced calcium carbonate precipitation (MICP) approach to reduce the percent of mass loss against erosive force of wind regarding to the concentration and characteristics of aggregate used, climate, and traffic amounts. The results of this study showed that the required precipitation for dust control of sand by 70% is less than 15 g CaCO 3 /m 2 between sand grains in bio-treated sand. The wind tunnel test results of this study also indicate that the effectiveness of the bio-treatment method for dust control depends on many variables, such as the percent of precipitated calcium carbonate and tensile strength.

Dispersion model on PM₂.₅ fugitive dust and trace metals levels in Kuwait Governorates.

PubMed

Bu-Olayan, A H; Thomas, B V

2012-03-01

Frequent dust storms and recent environmental changes were found to affect the human health especially in residents of arid countries. Investigations on the PM(2.5) fugitive dust in six Kuwait Governorate areas using dispersion Gaussian plume modeling revealed significant relationship between low rate of pollutant emission, low wind velocity, and stable weather conditions' matrix causing high rate of dust deposition in summer than in winter. The rate of dust deposition and trace metals levels in PM(2.5) were in the sequence of G-VI > G-I > G-II > G-V > G-III > G-IV. Trace metals were observed in the sequence of Al > Fe > Zn > Ni > Pb > Cd irrespective of the Governorate areas and the two seasons. The high rate of dust deposition and trace metals in PM(2.5) was reflected by the vast open area, wind velocity, and rapid industrialization besides natural and anthropogenic sources. A combination of air dispersion modeling and nephalometric and gravimetric studies of this kind not only determines the seasonal qualitative and quantitative analyses on the PM(2.5) dust deposition besides trace metals apportionment in six Kuwait Governorate areas, but also characterizes air pollution factors that could be used by environmentalist to deduce preventive measures.

Isotopically constrained lead sources in fugitive dust from unsurfaced roads in the southeast Missouri mining district.

PubMed

Witt, Emitt C; Pribil, Michael J; Hogan, John P; Wronkiewicz, David J

2016-09-01

The isotopic composition of lead (Pb) in fugitive dust suspended by a vehicle from 13 unsurfaced roads in Missouri was measured to identify the source of Pb within an established long-term mining area. A three end-member model using (207)Pb/(206)Pb and concentration as tracers resulted in fugitive dust samples plotting in the mixing field of well characterized heterogeneous end members. End members selected for this investigation include the (207)Pb/(206)Pb for 1) a Pb-mixture representing mine tailings, 2) aerosol Pb-impacted soils within close proximity to the Buick secondary recycling smelter, and 3) an average of soils, rock cores and drill cuttings representing the background conditions. Aqua regia total concentrations and (207)Pb/(206)Pb of mining area dust suggest that 35.4-84.3% of the source Pb in dust is associated with the mine tailings mixture, 9.1-52.7% is associated with the smelter mixture, and 0-21.6% is associated with background materials. Isotope ratios varied minimally within the operational phases of sequential extraction suggesting that mixing of all three Pb mixtures occurs throughout. Labile forms of Pb were attributed to all three end members. The extractable carbonate phase had as much as 96.6% of the total concentration associated with mine tailings, 51.8% associated with smelter deposition, and 34.2% with background. The next most labile geochemical phase (Fe + Mn Oxides) showed similar results with as much as 85.3% associated with mine tailings, 56.8% associated with smelter deposition, and 4.2% associated with the background soil. Published by Elsevier Ltd.

Isotopically constrained lead sources in fugitive dust from unsurfaced roads in the southeast Missouri mining district

USGS Publications Warehouse

Witt, Emitt C.; Pribil, Michael; Hogan, John P; Wronkiewicz, David

2016-01-01

The isotopic composition of lead (Pb) in fugitive dust suspended by a vehicle from 13 unsurfaced roads in Missouri was measured to identify the source of Pb within an established long-term mining area. A three end-member model using 207Pb/206Pb and concentration as tracers resulted in fugitive dust samples plotting in the mixing field of well characterized heterogeneous end members. End members selected for this investigation include the 207Pb/206Pb for 1) a Pb-mixture representing mine tailings, 2) aerosol Pb-impacted soils within close proximity to the Buick secondary recycling smelter, and 3) an average of soils, rock cores and drill cuttings representing the background conditions. Aqua regia total concentrations and 207Pb/206Pb of mining area dust suggest that 35.4–84.3% of the source Pb in dust is associated with the mine tailings mixture, 9.1–52.7% is associated with the smelter mixture, and 0–21.6% is associated with background materials. Isotope ratios varied minimally within the operational phases of sequential extraction suggesting that mixing of all three Pb mixtures occurs throughout. Labile forms of Pb were attributed to all three end members. The extractable carbonate phase had as much as 96.6% of the total concentration associated with mine tailings, 51.8% associated with smelter deposition, and 34.2% with background. The next most labile geochemical phase (Fe + Mn Oxides) showed similar results with as much as 85.3% associated with mine tailings, 56.8% associated with smelter deposition, and 4.2% associated with the background soil.

40 CFR 63.1651 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... continuously monitor relative particulate matter loadings. Capture system means the equipment (including hoods... due to wind or mechanical inducement such as vehicle traffic. Fugitive dust sources include plant...

40 CFR 63.1651 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... continuously monitor relative particulate matter loadings. Capture system means the equipment (including hoods... due to wind or mechanical inducement such as vehicle traffic. Fugitive dust sources include plant...

40 CFR 63.1651 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... continuously monitor relative particulate matter loadings. Capture system means the equipment (including hoods... due to wind or mechanical inducement such as vehicle traffic. Fugitive dust sources include plant...

Potential health benefits of controlling dust emissions in Beijing.

PubMed

Meng, Jing; Liu, Junfeng; Fan, Songmiao; Kang, Chuyun; Yi, Kan; Cheng, Yanli; Shen, Xing; Tao, Shu

2016-06-01

Although the adverse impact of fine particulate matter (i.e., PM2.5) on human health has been well acknowledged, little is known of the health effects of its specific constituents. Over the past decade, the annual average dust concentrations in Beijing were approximately ∼14 μg m(-3), a value that poses a great threat to the city's 20 million residents. In this study, we quantify the potential long-term health damages in Beijing resulting from the dust exposure that occurred from 2000 to 2011. Each year in Beijing, nearly 4000 (95% CI: 1000-7000) premature deaths may be associated with long-term dust exposure, and ∼20% of these deaths are attributed to lung cancer. A decomposition analysis of the inter-annual variability of premature deaths in Beijing indicates that dust concentrations determine the year-to-year tendency, whereas population growth and lung cancer mortality rates drive the increasing tendency of premature death. We suggest that if Beijing takes effective measures towards reducing dust concentrations (e.g., controlling the resuspension of road dust and the fugitive dust from construction sites) to a level comparable to that of New York City's, the associated premature deaths will be significantly reduced. This recommendation offers "low-hanging fruit" suggestions for pollution control that would greatly benefit the public health in Beijing. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fugitive dust mitigation for PM{sub 10} attainment in the western Mojave Desert: Recommendations on revegetation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grantz, D.A.; Vaughn, D.L.; Roberts, E.

1997-12-31

Methods to suppress fugitive dust and associated violations of federal PM{sub 10} standards in the western Mojave Desert, following removal of native vegetation by tillage or overgrazing, have been under investigation by a multi-agency task force for several years. Interim recommendations are now possible for this area of high winds, low rainfall, and mostly arable soil with patchy blowing sand. There can be no guarantee of success in any revegetation program in the desert, but the greatest probability of success in this area can be attained by using the native shrub Atriplex canescens, whether direct seeded or transplanted. No additionalmore » nitrogen should be added, and excess nitrogen should be removed if possible, perhaps by a preliminary cropping of barley. This will itself stabilize the soil surface in the short term. Young plants should be protected from herbivory and the harsh elements by using plastic cones. Irrigation is helpful if available. In areas located near native populations of rabbitbrush annual plant cover should be burned but no tillage or other soil disturbance should be imposed, as this facilitates invasion of annual species, including russian thistle, and prevents establishment of rabbitbrush. In sandy areas, seeding with Indian ricegrass may be more effective than with A. canescens. For immediate, short-term, mitigation of blowing dust, furrowing alone and installation of windfences may be effective. Rainfall exhibits high annual variability in arid regions. Absence of fugitive dust emissions in rainy periods, associated with ground cover by annual vegetation, is unlikely to survive several years of low, but normal, rainfall. It is precisely during those periods when rainfall is adequate that long-term revegetation with shrubs has the best chance of success.« less

Health Effects of Petroleum Coke

EPA Pesticide Factsheets

Significant quantities of fugitive dust from pet coke storage and handling operations present a health risk. EPA’s research suggests that petcoke does not pose a different health risk than similar-sized particulate matter (PM10).

Fugitive Dust Emissions: Development of a Real-time Monitor

DTIC Science & Technology

2011-10-01

the mechanical disturbance of soils which injects particles into the air. Common sources of FD include vehicles driving on unpaved roads...agricultural tilling, and heavy construction operations. For these sources the dust-generation process is caused by two basic physical phenomena...visibility, source apportionment , etc. The PM10 standard set by the U.S. Environmental Protection Agency in 1987 is an example of size-selective

Optical remote sensing to quantify fugitive particulate mass emissions from stationary short-term and mobile continuous sources: part II. Field applications.

PubMed

Du, Ke; Yuen, Wangki; Wang, Wei; Rood, Mark J; Varma, Ravi M; Hashmonay, Ram A; Kim, Byung J; Kemme, Michael R

2011-01-15

Quantification of emissions of fugitive particulate matter (PM) into the atmosphere from military training operations is of interest by the United States Department of Defense. A new range-resolved optical remote sensing (ORS) method was developed to quantify fugitive PM emissions from puff sources (i.e., artillery back blasts), ground-level mobile sources (i.e., movement of tracked vehicles), and elevated mobile sources (i.e., airborne helicopters) in desert areas that are prone to generating fugitive dust plumes. Real-time, in situ mass concentration profiles for PM mass with particle diameters <10 μm (PM(10)) and <2.5 μm (PM(2.5)) were obtained across the dust plumes that were generated by these activities with this new method. Back blasts caused during artillery firing were characterized as a stationary short-term puff source whose plumes typically dispersed to <10 m above the ground with durations of 10-30 s. Fugitive PM emissions caused by artillery back blasts were related to the zone charge and ranged from 51 to 463 g PM/firing for PM(10) and 9 to 176 g PM/firing for PM(2.5). Movement of tracked vehicles and flying helicopters was characterized as mobile continuous sources whose plumes typically dispersed 30-50 m above the ground with durations of 100-200 s. Fugitive PM emissions caused by moving tracked vehicles ranged from 8.3 to 72.5 kg PM/km for PM(10) and 1.1 to 17.2 kg PM/km for PM(2.5), and there was no obvious correlation between PM emission and vehicle speed. The emission factor for the helicopter flying at 3 m above the ground ranged from 14.5 to 114.1 kg PM/km for PM(10) and 5.0 to 39.5 kg PM/km for PM(2.5), depending on the velocity of the helicopter and type of soil it flies over. Fugitive PM emissions by an airborne helicopter were correlated with helicopter speed for a particular soil type. The results from this range-resolved ORS method were also compared with the data obtained with another path-integrated ORS method and a Flux Tower method.

EPA Requires Beemsterboer and KCBX to Take Action

EPA Pesticide Factsheets

In response to complaints of fugitive pet coke dust, EPA issued Clean Air Act Section 114 information request letters to KCBX Terminals and Beemsterboer Slag petroleum coke facilities, and ordered onsite air quality monitoring and petcoke sample analysis.

40 CFR 52.620 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... on applications 11/29/1982 08/18/1983, 48 FR 37403 11-60-26 Fugitive dust 11/29/1982 08/18/1983, 48..., and 1997 and 2006 Fine Particulate Matter (PM2.5) National Ambient Air Quality Standards Statewide 12...

40 CFR 52.620 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... on applications 11/29/1982 08/18/1983, 48 FR 37403 11-60-26 Fugitive dust 11/29/1982 08/18/1983, 48... 2006 PM2.5 national ambient air quality standards. 342B-50 Disposition of collected fines and penalties...

40 CFR 63.1651 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... due to wind or mechanical inducement such as vehicle traffic. Fugitive dust sources include plant roadways, yard areas, and outdoor material storage and transfer operations. Furnace power input means the resistive electrical power consumption of a submerged arc furnace, expressed as megawatts (MW). Malfunction...

40 CFR 63.1651 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... due to wind or mechanical inducement such as vehicle traffic. Fugitive dust sources include plant roadways, yard areas, and outdoor material storage and transfer operations. Furnace power input means the resistive electrical power consumption of a submerged arc furnace, expressed as megawatts (MW). Malfunction...

Atmospheric Fate and Transport of Agricultural Dust and Ammonia

NASA Astrophysics Data System (ADS)

Hiranuma, N.; Brooks, S. D.; Thornton, D. C.; Auvermann, B. W.; Fitz, D. R.

2008-12-01

Agricultural fugitive dust and odor are significant sources of localized air pollution in the semi-arid southern Great Plains. Daily episodes of ground-level fugitive dust emissions from the cattle feedlots associated with increased cattle activity in the early evenings are routinely observed, while consistently high ammonia is observed throughout the day. Here we present measurements of aerosol size distributions and concentrations of gas and particulate phase ammonia species collected at a feedlot in Texas during summers of 2006, 2007 and 2008. A GRIMM sequential mobility particle sizer and GRIMM 1.108 aerosol spectrometer were used to determine aerosol size distributions in the range of 10 nm to 20 µm aerodynamic diameter at the downwind and upwind edges of the facility. Using aqueous scrubbers, simultaneous measurements of both gas phase and total ammonia species present in the gas and particle phases were also collected. In addition to the continuous measurements at the edges of the facility, coincident aerosol and ammonia measurements were obtain at an additional site further downwind (~3.5 km). Taken together our measurements will be used to quantify aerosol and ammonia dispersion and transport. Relationships between the fate and transport of the aerosols and ammonia will be discussed.

40 CFR 49.123 - General provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., road construction and road maintenance, fertilization, logging operations, and forest management... oil. Fugitive dust means a particulate matter emission made airborne by forces of wind, mechanical... § 49.123(a). (vii) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR approved for...

40 CFR 49.123 - General provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., road construction and road maintenance, fertilization, logging operations, and forest management... oil. Fugitive dust means a particulate matter emission made airborne by forces of wind, mechanical... § 49.123(a). (vii) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR approved for...

40 CFR 49.123 - General provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., road construction and road maintenance, fertilization, logging operations, and forest management... oil. Fugitive dust means a particulate matter emission made airborne by forces of wind, mechanical... § 49.123(a). (vii) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR approved for...

40 CFR 49.123 - General provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., road construction and road maintenance, fertilization, logging operations, and forest management... oil. Fugitive dust means a particulate matter emission made airborne by forces of wind, mechanical... § 49.123(a). (vii) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR approved for...

Characterization of the fugitive particulate emissions from construction mud/dirt carryout.

PubMed

Kinsey, John S; Linna, Kara J; Squier, William C; Muleski, Gregory E; Cowherd, Chatten

2004-11-01

Although the fugitive dust associated with construction mud/dirt carryout can represent a substantial portion of the particulate matter (PM) emissions inventory in nonattainment areas, it has not been well characterized by direct sampling methods. In this paper, a research program is described that directly determined both PM10 and PM2.5 (particles < or =10 and 2.5 microm in classical aerodynamic diameter, respectively) emission factors for mud/dirt carryout from a major construction project located in metropolitan Kansas City, MO. The program also assessed the contribution of automotive emissions to the total PM2.5 burden and determined the baseline emissions from the test road. As part of the study, both time-integrated and continuous exposure-profiling methods were used to assess the PM emissions, including particle size and elemental composition. This research resulted in overall PM10 and PM2.5 emission factors of 6 and 0.2 g/vehicle, respectively. Although PM10 is within the range of prior U.S. Environmental Protection Agency (EPA) guidance, the PM2.5 emission factor is far lower than previous estimates published by EPA. In addition, based on both the particle size and chemical data obtained in the study, a major portion of the PM2.5 emissions appears to be attributable to automotive exhaust from light-duty, gasoline-powered vehicles and not to the fugitive dust associated with reentrained mud/dirt carryout.

Trends in spatial patterns of heavy metal deposition on national park service lands along the Red Dog Mine haul road, Alaska, 2001-2006.

PubMed

Neitlich, Peter N; Ver Hoef, Jay M; Berryman, Shanti D; Mines, Anaka; Geiser, Linda H; Hasselbach, Linda M; Shiel, Alyssa E

2017-01-01

Spatial patterns of Zn, Pb and Cd deposition in Cape Krusenstern National Monument (CAKR), Alaska, adjacent to the Red Dog Mine haul road, were characterized in 2001 and 2006 using Hylocomium moss tissue as a biomonitor. Elevated concentrations of Cd, Pb, and Zn in moss tissue decreased logarithmically away from the haul road and the marine port. The metals concentrations in the two years were compared using Bayesian posterior predictions on a new sampling grid to which both data sets were fit. Posterior predictions were simulated 200 times both on a coarse grid of 2,357 points and by distance-based strata including subsets of these points. Compared to 2001, Zn and Pb concentrations in 2006 were 31 to 54% lower in the 3 sampling strata closest to the haul road (0-100, 100-2000 and 2000-4000 m). Pb decreased by 40% in the stratum 4,000-5,000 m from the haul road. Cd decreased significantly by 38% immediately adjacent to the road (0-100m), had an 89% probability of a small decrease 100-2000 m from the road, and showed moderate probabilities (56-71%) for increase at greater distances. There was no significant change over time (with probabilities all ≤ 85%) for any of the 3 elements in more distant reference areas (40-60 km). As in 2001, elemental concentrations in 2006 were higher on the north side of the road. Reductions in deposition have followed a large investment in infrastructure to control fugitive dust escapement at the mine and port sites, operational controls, and road dust mitigation. Fugitive dust escapement, while much reduced, is still resulting in elevated concentrations of Zn, Pb and Cd out to 5,000 m from the haul road. Zn and Pb levels were slightly above arctic baseline values in southern CAKR reference areas.

Trends in spatial patterns of heavy metal deposition on national park service lands along the Red Dog Mine haul road, Alaska, 2001–2006

PubMed Central

Ver Hoef, Jay M.; Berryman, Shanti D.; Mines, Anaka; Geiser, Linda H.; Hasselbach, Linda M.; Shiel, Alyssa E.

2017-01-01

Spatial patterns of Zn, Pb and Cd deposition in Cape Krusenstern National Monument (CAKR), Alaska, adjacent to the Red Dog Mine haul road, were characterized in 2001 and 2006 using Hylocomium moss tissue as a biomonitor. Elevated concentrations of Cd, Pb, and Zn in moss tissue decreased logarithmically away from the haul road and the marine port. The metals concentrations in the two years were compared using Bayesian posterior predictions on a new sampling grid to which both data sets were fit. Posterior predictions were simulated 200 times both on a coarse grid of 2,357 points and by distance-based strata including subsets of these points. Compared to 2001, Zn and Pb concentrations in 2006 were 31 to 54% lower in the 3 sampling strata closest to the haul road (0–100, 100–2000 and 2000–4000 m). Pb decreased by 40% in the stratum 4,000–5,000 m from the haul road. Cd decreased significantly by 38% immediately adjacent to the road (0–100m), had an 89% probability of a small decrease 100–2000 m from the road, and showed moderate probabilities (56–71%) for increase at greater distances. There was no significant change over time (with probabilities all ≤ 85%) for any of the 3 elements in more distant reference areas (40–60 km). As in 2001, elemental concentrations in 2006 were higher on the north side of the road. Reductions in deposition have followed a large investment in infrastructure to control fugitive dust escapement at the mine and port sites, operational controls, and road dust mitigation. Fugitive dust escapement, while much reduced, is still resulting in elevated concentrations of Zn, Pb and Cd out to 5,000 m from the haul road. Zn and Pb levels were slightly above arctic baseline values in southern CAKR reference areas. PMID:28542369

78 FR 52485 - Revisions to the Arizona State Implementation Plan, Maricopa County Area

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-23

...] Revisions to the Arizona State Implementation Plan, Maricopa County Area AGENCY: Environmental Protection... County Area portion of the Arizona State Implementation Plan (SIP). These revisions concern particulate matter (PM) emissions from fugitive dust sources. We are approving local statutes that regulate these...

CHARACTERIZATION OF MUD/DIRT CARRYOUT ONTO PAVED ROADS FROM CONSTRUCTION AND DEMOLITION ACTIVITIES

EPA Science Inventory

The report characterizes fugitive dust generated by vehicular traffic on paved streets and highways resulting from mud/dirt carryout from unpaved areas as a primary source of PM-10 (particles = or < 10 micrometers in aerodynamic diameter), and evaluates three technologies for eff...

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., and other surfaces that can create airborne dust. (iii) Full or partial enclosure of materials... particulate matter from becoming airborne. (iv) Implementation of good housekeeping practices to avoid or minimize the accumulation of dusty materials that have the potential to become airborne, and the prompt...

Use of Anthropogenic Radioisotopes to Estimate Rates of Soil Redistribution by Wind

USDA-ARS?s Scientific Manuscript database

Wind erosion results in soil degradation and fugitive dust emissions. The temporal and spatial variability of aeolian processes makes local estimates of long-term average erosion costly and time consuming. Atmospheric testing of nuclear weapons during the 1950s and 1960s resulted in previously non...

Fugitive dust emissions from off-road vehicle maneuvers on military training lands

USDA-ARS?s Scientific Manuscript database

Off-road vehicle training can contribute to air quality degradation because of increased wind erosion as a result of soil disruption during high wind events. However, limited information exists regarding the impacts of off-road vehicle maneuvering on wind erosion potential of soils. This study was c...

40 CFR 49.124 - Rule for limiting visible emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...% opacity limit. (3) The visible emissions from an oil-fired boiler or solid fuel-fired boiler that..., fuel, fuel oil, fugitive dust, gaseous fuel, grate cleaning, marine vessel, mobile sources, motor..., PM10, PM2.5, reference method, refuse, Regional Administrator, residual fuel oil, smudge pot, solid...

40 CFR 49.124 - Rule for limiting visible emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...% opacity limit. (3) The visible emissions from an oil-fired boiler or solid fuel-fired boiler that..., fuel, fuel oil, fugitive dust, gaseous fuel, grate cleaning, marine vessel, mobile sources, motor..., PM10, PM2.5, reference method, refuse, Regional Administrator, residual fuel oil, smudge pot, solid...

Evaluation of Uncertainties in Measuring Particulate Matter Emission Factors from Atmospheric Fugitive Sources Using Optical Remote Sensing

NASA Astrophysics Data System (ADS)

Yuen, W.; Ma, Q.; Du, K.; Koloutsou-Vakakis, S.; Rood, M. J.

2015-12-01

Measurements of particulate matter (PM) emissions generated from fugitive sources are of interest in air pollution studies, since such emissions vary widely both spatially and temporally. This research focuses on determining the uncertainties in quantifying fugitive PM emission factors (EFs) generated from mobile vehicles using a vertical scanning micro-pulse lidar (MPL). The goal of this research is to identify the greatest sources of uncertainty of the applied lidar technique in determining fugitive PM EFs, and to recommend methods to reduce the uncertainties in this measurement. The MPL detects the PM plume generated by mobile fugitive sources that are carried downwind to the MPL's vertical scanning plane. Range-resolved MPL signals are measured, corrected, and converted to light extinction coefficients, through inversion of the lidar equation and calculation of the lidar ratio. In this research, both the near-end and far-end lidar equation inversion methods are considered. Range-resolved PM mass concentrations are then determined from the extinction coefficient measurements using the measured mass extinction efficiency (MEE) value, which is an intensive PM property. MEE is determined by collocated PM mass concentration and light extinction measurements, provided respectively by a DustTrak and an open-path laser transmissometer. These PM mass concentrations are then integrated with wind information, duration of plume event, and vehicle distance travelled to obtain fugitive PM EFs. To obtain the uncertainty of PM EFs, uncertainties in MPL signals, lidar ratio, MEE, and wind variation are considered. Error propagation method is applied to each of the above intermediate steps to aggregate uncertainty sources. Results include determination of uncertainties in each intermediate step, and comparison of uncertainties between the use of near-end and far-end lidar equation inversion methods.

A new approach to developing a fugitive road dust emission inventory and emission trend from 2006 to 2010 in the beijing metropolitan area, china.

PubMed

Fan, Shoubin; Tian, Gang; Cheng, Shuiyuan; Qin, Jianping

2013-07-01

The USEPA emission factor (AP-42) of fugitive road dust (FRD) is widely used in establishing emission inventories. However, road silt loading sampling for AP-42 is expensive, time consuming, and dangerous. Therefore, a new method for establishing emission inventories based on road dust-fall (DF) monitors is described. Between January 2006 and December 2010, DF was monitored at 40 sites (80 samples), and background dust fall (DF) was monitored at 14 sites in the Beijing metropolitan area. Also during this period, 58 samples of road silt loadings were taken and used in the AP-42 emission factor equation to calculate FRD with particulate matter ≤10 μm in diameter [FRD(PM)] emission from the roads. Simultaneous measurement of FRD(PM) emissions calculated by AP-42 and ΔDF (i.e., the difference between the DF and DF) measured using gauges showed that the FRD(PM) emission for road dust was proportional to the ΔDF ( = 0.92). The FRD(PM) emission (kg km × 30 d) was calculated using the monitored ΔDF (t km × 30 d) by the formulation FRD(PM) = 278.3 × ΔDF - 1151.2. The ΔDF showed a general decline from 2006 to 2010. In particular, there was a sharp decline in August, September, and October 2008 due to strict dust controls enforced during the 2008 Olympic Games. Although there was a small increase in ΔDF after the Games, by the end of 2010 values were still lower than those before the Games. Using the 2006 ΔDF value as a benchmark, ΔDF values declined by 24.7, 33.0, 38.3, and 31.4% in 2007, 2008, 2009, and 2010, respectively. Based on using AP-42 calculations from silt loading and traffic information in 2007, the FRD(PM) emission distribution in the Beijing metropolitan area was mapped, and there were 2.05 × 10 tons of FRD(PM) emitted in 2007. The FRD(PM) from 2006 to 2010 was calculated by the ΔDF values. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

40 CFR 49.124 - Rule for limiting visible emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... emissions. (a) What is the purpose of this section? This section limits the visible emissions of air... residential buildings with four or fewer dwelling units, fugitive dust from public roads owned or maintained... sources. (d) What are the opacity limits for air pollution sources? (1) The visible emissions from an air...

40 CFR 52.1770 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 61213 Sect .0515 Particulates from Miscellaneous Industrial Processes 04/01/03 09/17/03, 68 FR 54362... Utility Boilers 08/01/91 02/14/96, 61 FR 5689 Sect .0540 Particulates from Fugitive Non-process Dust... Sect .0955 Thread Bonding Manufacturing 04/01/95 02/01/96, 62 FR 3589 Sect .0956 Glass Christmas...

Exposure-Reducing Behaviors among Residents Living near a Coal Ash Storage Site

ERIC Educational Resources Information Center

Zierold, Kristina M.; Sears, Clara G.; Brock, Guy N.

2016-01-01

Coal ash, a waste product generated from burning coal for energy, is composed of highly respirable particles containing heavy metals, radioactive elements, and polycylic aromatic hydrocarbons. Coal ash is stored in landfills and surface impoundments frequently located near neighborhoods. Fugitive dust from the storage sites exposes neighborhoods,…

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

40 CFR 63.545 - What are my standards for fugitive dust sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (4) Battery storage area. (5) Equipment maintenance. (6) Material storage areas. (7) Material... achieve 99.97 percent capture efficiency for 0.3 micron particles in a manner that does not generate... 40 CFR 302.4). (4) Battery storage areas. You must inspect any batteries that are not stored in a...

Emission factors for fugitive dust from bulldozers working on a coal pile.

PubMed

Mueller, Stephen F; Mallard, Jonathan W; Mao, Qi; Shaw, Stephanie L

2015-01-01

A study of a Powder River Basin (PRB) coal pile found that fugitive emissions from natural and human activity each produced similar levels of downwind fine + coarse (i.e., smaller than 10 µm, or PM10) particle mass concentrations. Natural impacts were statistically removed from downwind measurements to estimate emission factor Ev for bulldozers working on the pile. The Ev determined here was similar in magnitude to emission factors (EFs) computed using a U.S. Environmental Protection Agency (EPA) formulation for unpaved surfaces at industrial sites, even though the latter was not based on data for coal piles. EF formulations from this study and those in the EPA guidance yield values of similar magnitude but differ in the variables used to compute Ev variations. EPA studies included effects of surface silt fraction and vehicle weight, while the present study captured the influence of coal moisture. Our data indicate that the relationship between PRB coal fugitive dust Ev (expressed as mass of PM10 emitted per minute of bulldozer operation) and coal moisture content Mc (in percent) at the study site is best expressed as Ev =10(f(Mc())) where f(Mc) is a function of moisture. This function was determined by statistical regression between log10(Ev) and Mc where both Ev and Mc are expressed as daily averages of observations based on 289 hours sampled during 44 days from late June through mid-November of 2012. A methodology is described that estimates Mc based on available meteorological data (precipitation amount and solar radiation flux). An example is given of computed variations in daily Ev for an entire year. This illustrates the sensitivity of the daily average particulate EF to meteorological variability at one location. Finally, a method is suggested for combining the moisture-sensitive formulation for Ev with the EPA formulation to accommodate a larger number of independent variables that influence fugitive emissions.

Proceedings from the Workshop on Research Needs for Assessment and Management of Non-Point Air Emissions from Department of Defense Activities held in Research Triangle Park, North Carolina on 19-21 February 2008

DTIC Science & Technology

2008-10-01

Chow, J.C. (2006). Feasibility of soil dust source apportionment by the pyrolysis-gas chromatography/mass spectrometry method. J. Air Waste Manage...receptor-oriented source apportionment models. • Develop monitoring methods to determine source and fence line amounts of fugitive dust emissions for...offsite impact, including evaluation with receptor- oriented source apportionment models 76 8.8.1 Background 76 8.8.2 Significance 77 8.8.3

Petrogenic organic carbon and PAHs in snow deposited on Athabasca oil sands region lakes

NASA Astrophysics Data System (ADS)

Ahad, J. M.; Pakdel, H.; Gammon, P. R.; Savard, M. M.

2017-12-01

Fugitive dust associated with surface mining activities is one of the principal vectors for transport of airborne contaminants in Canada's Athabasca oil sands (AOS) region. The two main sources for mining-related dust - unprocessed oil sand and petroleum coke (petcoke) - contain high levels of bitumen-derived organic contaminants such as polycyclic aromatic hydrocarbons (PAHs). Here, we report the radiocarbon (14C) contents of solvent-extractable organics in snow particulates deposited during the winter of 2016-17 on fourteen lakes across the AOS region to quantify the contribution of anthropogenic dust transported directly to these ecosystems. Concentrations of parent and alkylated PAHs were determined in both dissolved and particulate fractions of snow. Radiocarbon isotope ratios (Δ14C) ranged from -805 to -177‰, indicating a significant contribution of petrogenic or fossil (i.e., Δ14C = -1000‰) carbon in snowpack dust at some sites. More negative Δ14C values were generally found in samples containing higher levels of particulate matter and at lakes closer to the geographic center of AOS mining operations. Concentrations of PAHs > 2 rings were significantly higher in the particulate phase and in samples with the largest petrogenic carbon components. Relatively high levels of PAHs at some distal sites associated with less negative Δ14C values pointed to an important modern carbon contribution, potentially ash originating from the 1.5 million acre 2016 Fort McMurray wildfire. As demonstrated here, fugitive dust in snow covering AOS region lakes can contain significant petrogenic organic carbon and high levels of PAHs, particularly in areas close (i.e., < 25 km) to the center of AOS mining operations. The spring snowmelt thus provides a direct pathway for mining-related contaminants to lake sediments.

Temporal and Spatial Variations in Fine and Coarse Particles in Seoul, Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghim, Young Sung

2015-01-01

Concentrations of fine (PM2.5) and coarse particles (PM10 -2.5), whose diameters are less 2.5 µm, and between 2.5 and 10 µm, respectively, at ambient air monitoring stations in Seoul between 2002 and 2008 were analyzed. Effects of Asian dust are mainly manifested as concentration spikes of PM10 - 2.5 but were considerable on PM2.5 levels in 2002 when Asian dust storms were the strongest. Excluding the effects of Asian dust, annual average PM2.5 showed a downward trend. Despite a similarity in year - to - year variations, PM10- 2.5, mostly affected by fugitive dust emissions, and CO and NO2, primarilymore » affected by motor vehicle emissions, did not show a decrease. PM2.5 along with CO and NO2 had the highest values during the morning rush hour. PM10 - 2.5 peak lagged about one hour behind that of PM2.5 because of fugitive dust emissions despite an increasing mixing height. On high PM2.5 days, PM2. 5 peaks occurred two hours later than usual as the effects of secondary formation became more important. A test for the spatial variabilities shows that PM10 - 2.5, which is known to be greatly influenced by local effects, is lower in its correlation coeffic ient and higher in its coefficient of divergence (COD, which serves as an indicator for spatial variability) than PM2.5, albeit that the difference between the two is small. The average COD of PM2.5 among monitoring stations was about 0.2 but was lowered t o 0.13 when considering high PM2.5 days only, which signifies that spatial uniformity increases significantly.« less

Dust emissions from unpaved roads on the Colorado Plateau

NASA Astrophysics Data System (ADS)

Duniway, M.; Flagg, C.; Belnap, J.

2013-12-01

On the Colorado Plateau, elevated levels of aeolian dust have become a major land management and policy concern due to its influence on climate, weather, terrestrial ecosystem dynamics, landscape development and fertility, melting of snow and ice, air quality, and human health. Most desert soil surfaces are stabilized by plants, rocks, and/or physical or biological soil crusts, but once disturbed, sediment production from these surfaces can increase dramatically. Road development and use is a common surface disturbing activity in the region. The extent and density of roads and road networks is rapidly increasing due to continued energy exploration, infrastructure development, and off-highway recreation activities. Though it is well known that unpaved roads produce dust, the relative contribution of dust from existing roads or the implications of future road development to regional dust loading is unknown. To address this need, we have initiated a multifaceted research effort to evaluating dust emissions from unpaved roads regionally. At 34 sites arranged across various road surfaces and soil textures in southeastern Utah, we are: 1) monitoring dust emissions, local wind conditions, and vehicle traffic and 2) evaluating fugitive dust potential using a portable wind tunnel and measuring road characteristics that affect dust production. We will then 3) develop a GIS-based model that integrates results from 1 & 2 to estimate potential dust contributions from current and future scenarios of regional road development. Passive, horizontal sediment traps were installed at three distances downwind from the road edge. One control trap was placed upwind of the samplers to account for local, non-road dust emissions. An electronic vehicle counter and anemometer were also installed at monitoring sites. Dust samples were collected every three months at fixed heights, 15 cm up to 100 cm above the soil surface, from March 2010 to the present. Threshold friction velocities (TFV), the minimum wind velocity required to initiate erosion, and sediment production were also quantified using a portable wind tunnel at monitoring sites. Additionally, numerous characteristics including gravel cover, particle-size distribution, soil compaction, and loose-erodible material were measured on road surfaces at monitoring sites. Preliminary results suggest that roads are an important regional dust source, as emissions from roads are comparable to non-road, rural sources that are being monitored concurrently. While gravel roads produce more dust per day on average, per vehicle emissions are larger on dirt roads. Dust flux decreases with distance from the road edge on all road types, however this decline is less pronounced on dirt roads. Portable wind tunnel results indicate that TFV is consistently lower on dirt versus gravel roads across all soil types. Fugitive dust flux is generally larger and more variable on dirt roads compared to gravel roads. Initial analyses suggest that several easily measurable road surface characteristics can potentially be used to predict both TFV and sediment production, including: total gravel cover, gravel particle-size classes, clay content, and road compaction. The relation between TFV and total gravel cover in particular appears to be non-linear, with TFV increasing rapidly above ~40% gravel cover.

78 FR 27071 - Approval and Promulgation of Air Quality Implementation Plans; Alaska: Mendenhall Valley...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-09

... lungs and cause serious adverse health effects. People with heart or lung diseases, children and older...) submitted with the Mendenhall Valley NAA PM 10 LMP, for base year 2004 and projected year 2018, identifies... projected to remain close to that level through 2018. Fugitive dust emissions from travel on unpaved roads...

Lidar characterization of crystalline silica generation and transport from a sand and gravel plant.

PubMed

Trzepla-Nabaglo, Krystyna; Shiraki, Ryoji; Holmén, Britt A

2006-04-30

Light detection and ranging (Lidar) remote sensing two-dimensional vertical and horizontal scans collected downwind of a sand and gravel plant were used to evaluate the generation and transport of geologic fugitive dust emitted by quarry operations. The lidar data give unsurpassed spatial resolution of the emitted dust, but lack quantitative particulate matter (PM) mass concentration data. Estimates of the airborne PM10 and crystalline silica concentrations were determined using linear relationships between point monitor PM10 and quartz content data with the lidar backscatter signal collected from the point monitor location. Lidar vertical profiles at different distances downwind from the plant were used to quantify the PM10 and quartz horizontal fluxes at 2-m vertical resolution as well as off-site emission factors. Emission factors on the order of 65-110 kg of PM10 (10-30 kg quartz) per daily truck activity or 2-4 kg/t product shipped (0.5-1 kg quartz/t) were quantified for this facility. The lidar results identify numerous elevated plumes at heights >30 m and maximum plume heights of 100 m that cannot be practically sampled by conventional point sampler arrays. The PM10 and quartz mass flux was greatest at 10-25 m height and decreased with distance from the main operation. Measures of facility activity were useful for explaining differences in mass flux and emission rates between days. The study results highlight the capabilities of lidar remote sensing for determining the spatial distribution of fugitive dust emitted by area sources with intermittent and spatially diverse dust generation rates.

Particulate matter over a seven year period in urban and rural areas within, proximal and far from mining and power station operations in Greece.

PubMed

Triantafyllou, A G; Zoras, S; Evagelopoulos, V

2006-11-01

Lignite mining operations and lignite-fired power stations result in major particulate pollution (fly ash and fugitive dust) problems in the areas surrounding these activities. The problem is more complicated, especially, for urban areas located not far from these activities, due to additional contribution from the urban pollution sources. Knowledge of the distribution of airborne particulate matter into size fraction has become an increasing area of focus when examining the effects of particulate pollution. On the other hand, airborne particle concentration measurements are useful in order to assess the air pollution levels based on national and international air quality standards. These measurements are also necessary for developing air pollutants control strategies or for evaluating the effectiveness of these strategies, especially, for long periods. In this study an attempt is made in order to investigate the particle size distribution of fly ash and fugitive dust in a heavy industrialized (mining and power stations operations) area with complex terrain in the northwestern part of Greece. Parallel total suspended particulates (TSP) and particulate matter with an aerodynamic diameter less than 10 microm (PM10) concentrations are analyzed. These measurements gathered from thirteen monitoring stations located in the greater area of interest. Spatial, temporal variation and trend are analyzed over the last seven years. Furthermore, the geographical variation of PM10 - TSP correlation and PM10/TSP ratio are investigated and compared to those in the literature. The analysis has indicated that a complex system of sources and meteorological conditions modulate the particulate pollution of the examined area.

Global dust sources detection using MODIS Deep Blue Collection 6 aerosol products

NASA Astrophysics Data System (ADS)

Pérez García-Pando, C.; Ginoux, P. A.

2015-12-01

Our understanding of the global dust cycle is limited by a dearth of information about dust sources, especially small-scale features which could account for a large fraction of global emissions. Remote sensing sensors are the most useful tool to locate dust sources. These sensors include microwaves, visible channels, and lidar. On the global scale, major dust source regions have been identified using polar orbiting satellite instruments. The MODIS Deep Blue algorithm has been particularly useful to detect small-scale sources such as floodplains, alluvial fans, rivers, and wadis , as well as to identify anthropogenic sources from agriculture. The recent release of Collection 6 MODIS aerosol products allows to extend dust source detection to the entire land surfaces, which is quite useful to identify mid to high latitude dust sources and detect not only dust from agriculture but fugitive dust from transport and industrial activities. This presentation will overview the advantages and drawbacks of using MODIS Deep Blue for dust detection, compare to other instruments (polar orbiting and geostationary). The results of Collection 6 with a new dust screening will be compared against AERONET. Applications to long range transport of anthropogenic dust will be presented.

Methamphetamine

MedlinePlus

... OPERATIONS Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip DRUG INFO Drug Fact Sheets ... Operations Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip Drug Info Drug Fact Sheets ...

Narcotics

MedlinePlus

... OPERATIONS Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip DRUG INFO Drug Fact Sheets ... Operations Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip Drug Info Drug Fact Sheets ...

Hydrocodone

MedlinePlus

... OPERATIONS Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip DRUG INFO Drug Fact Sheets ... Operations Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip Drug Info Drug Fact Sheets ...

USER'S GUIDE: EMISSION CONTROL TECHNOLOGIES AND EMISSION FACTORS FOR UNPAVED ROAD FUGITIVE EMISSIONS

EPA Science Inventory

This document assists control agency personnel in evaluating unpaved road fugitive emissions control plans and helps industry personnel develop effective control strategies for unpaved roads. he brochure describes control techniques for reducing unpaved road emissions and methods...

Heroin Photos

MedlinePlus

... OPERATIONS Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip DRUG INFO Drug Fact Sheets ... Operations Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip Drug Info Drug Fact Sheets ...

Road dust and its effect on human health: a literature review

PubMed Central

2018-01-01

The purpose of this study was to determine the effects of road dust on human health. A PubMed search was used to extract references that included the words “road dust” and “health” or “fugitive dust” and “health” in the title or abstract. A total of 46 references were extracted and selected for review after the primary screening of 949 articles. The respiratory system was found to be the most affected system in the human body. Lead, platinum-group elements (platinum, rhodium, and bohrium), aluminum, zinc, vanadium, and polycyclic aromatic hydrocarbons were the components of road dust that were most frequently referenced in the articles reviewed. Road dust was found to have harmful effects on the human body, especially on the respiratory system. To determine the complex mechanism of action of various components of road dust on the human body and the results thereof, the authors recommend a further meta-analysis and extensive risk-assessment research into the health impacts of dust exposure. PMID:29642653

75 FR 17307 - Revisions to the Arizona State Implementation Plan; Pinal County

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-06

... Standards--Hayden 01/07/09 06/12/09 PM10 Non-attainment Area. 4-2-020 Fugitive Dust--General 12/04/02 06/12... Standards--Hayden PM-10 Non- attainment Area,'' adopted on January 7, 2009. (i) Pinal County Board of... District Rules, adopted January 7, 2009; to Wit: Rule 2-8-302 (Performance Standards--Hayden PM10...

Methamphetamine Lab Incidents, 2004-2014

MedlinePlus

... OPERATIONS Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip DRUG INFO Drug Fact Sheets ... Operations Diversion Control Programs Most Wanted Fugitives Training Intelligence Submit a Tip Drug Info Drug Fact Sheets ...

Lead contamination around secondary smelters: estimation of dispersal and accumulation by humans.

PubMed

Roberts, T M; Hutchinson, T C; Paciga, J; Chattopadhyay, A; Jervis, R E; VanLoon, J; Parkinson, D K

1974-12-20

A high rate of lead fallout around two secondary lead smelters originated mainly from episodal large-particulate emissions from low-level fugitive sources rather than from stack fumes. The lead content of dustfall, and consequently of soil, vegetation, and outdoor dust, decreased exponentially with distance from the two smelters. Between 13 and 30 percent of the children living in the contaminated areas had absorbed excessive amounts of lead (more than 40 micrograms per 100 milliliters of blood and more than 100 micrograms per gram of hair) as compared with less than 1 percent in a control group. A relationship between blood and hair was established which indicated that the absorption was fairly constant for most children examined. It seemned that the ingestion of contaminated dirt and dusts rather than "paint pica" was the major route of lead intake. Metabolic changes were found in most of 21 children selected from those with excessive lead absorption; 10 to 15 percent of this group showed subtle neurological dysfunctions and minor psychomotor abnormalities.

Measurement and Modeling of Fugitive Dust from Off Road DoD Activities

DTIC Science & Technology

2017-12-08

each soil and vehicle type (see Table 2). Note, no tracked vehicles were run at YTC. CT is the curve track sampling location, CR is the curve ridge...Soil is SL = sandy loam. ...................... 116 Figure 35. Single-event Wind Erosion Evaluation Program (SWEEP) Run example results. ... 121...Figure 36. Single-event Wind Erosion Evaluation Program (SWEEP) Threshold Run example results screen

Environmental Assessment: Maintenance of the Bear Lake Storm Water Retention Pond Whiteman Air Force Base, Missouri

DTIC Science & Technology

2010-10-01

Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202-4302. Respondents should be...and fugitive dust The noise environment due to construction vehicle operations Biological resources and wetlands due to land and water disturbance...construction vehicle operations ; Biological resources and wetlands due to land and water disturbance; Water quality due to land and water disturbance

Air quality as a constraint to the use of coal in California

NASA Technical Reports Server (NTRS)

Austin, T. C.

1978-01-01

Low-NOx burners, wet scrubbing systems, baghouses and ammonia injection systems are feasible for use on large combustion sources such as utility boilers. These devices, used in combination with coal handling techniques which minimize fugitive dust and coal transportation related emissions, should enable new power plants and large industrial boilers to burn coal without the adverse air quality impacts for which coal became notorious.

Salt Efflorescence Effects on Soil Surface Erodibility and Dust Emissions

NASA Astrophysics Data System (ADS)

Van Pelt, R. S.; Zhang, G.

2017-12-01

Soluble salts resulting from weathering of geological materials often form surface crusts or efflorescences in areas with shallow saline groundwater. In many cases, the affected areas are susceptible to wind erosion due to their lack of protective vegetation and their flat topography. Fugitive dusts containing soluble salts affect the biogeochemistry of deposition regions and may result in respiratory irritation during transport. We created efflorescent crusts on soil trays by surface evaporation of single salt solutions and bombarded the resultant efflorescences with quartz abrader sand in a laboratory wind tunnel. Four replicate trays containing a Torrifluvent soil affected by one of nine salts commonly found in arid and semiarid streams were tested and the emissions were captured by an aspirated multi-stage deposition and filtering system. We found that in most cases the efflorescent crust reduced the soil surface erodibility but also resulted in the emission of salt rich dust. Two of the salts, sodium thiosulfate and calcium chloride, resulted in increased soil volume and erodibility. However, one of the calcium chloride replicates was tested after an outbreak of humid air caused hygroscopic wetting of the soil and it became indurated upon drying greatly decreasing the erodibility. Although saline affected soils are not used for agricultural production and degradation is not a great concern, the release of salt rich dust is an area of environmental concern and steps to control the dust emissions from affected soils should be developed. Future testing will utilize suites of salts found in streams of arid and semiarid regions.

Environmental Assessment for the Radar Tomography Range and Equipment Storage Facility, Wright-Patterson Air Force Base, Ohio

DTIC Science & Technology

2012-10-01

relocated to Wright-Patterson AFB, and therefore, the antenna to~ e ! ring and services must relocate to Wright-Patterson AFB to continue the AFRLIRY...Support, 88 ABW/CEANQ, Wright‐Patterson Air Force Base.  E ‐ mail to Tamar Krantz, Labat Environmental regarding Title V and fugitive dust permits April...Greene, and Montgomery  Counties, Ohio. Division of Air Pollution Control. May 2011. Accessed on August 28, 2011 at  http://www.epa.ohio.gov/ portals /27

Source apportionment of fine particles and its chemical components over the Yangtze River Delta, China during a heavy haze pollution episode

NASA Astrophysics Data System (ADS)

Li, L.; An, J. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Lu, Q.; Lin, L.; Wang, Y. J.; Tao, S. K.; Qiao, L. P.; Zhu, S. H.; Chen, C. H.

2015-12-01

An extremely high PM2.5 pollution episode occurred over the eastern China in January 2013. In this paper, the particulate matter source apportionment technology (PSAT) method coupled within the Comprehensive air quality model with extensions (CAMx) is applied to study the source contributions to PM2.5 and its major components at six receptors (Urban Shanghai, Chongming, Dianshan Lake, Urban Suzhou, Hangzhou and Zhoushan) in the Yangtze River Delta (YRD) region. Contributions from 4 source areas (including Shanghai, South Jiangsu, North Zhejiang and Super-region) and 9 emission sectors (including power plants, industrial boilers and kilns, industrial processing, mobile source, residential, volatile emissions, dust, agriculture and biogenic emissions) to PM2.5 and its major components (sulfate, nitrate, ammonia, organic carbon and elemental carbon) at the six receptors in the YRD region are quantified. Results show that accumulation of local pollution was the largest contributor during this air pollution episode in urban Shanghai (55%) and Suzhou (46%), followed by long-range transport (37% contribution to Shanghai and 44% to Suzhou). Super-regional emissions play an important role in PM2.5 formation at Hangzhou (48%) and Zhoushan site (68%). Among the emission sectors contributing to the high pollution episode, the major source categories include industrial processing (with contributions ranging between 12.7 and 38.7% at different receptors), combustion source (21.7-37.3%), mobile source (7.5-17.7%) and fugitive dust (8.4-27.3%). Agricultural contribution is also very significant at Zhoushan site (24.5%). In terms of the PM2.5 major components, it is found that industrial boilers and kilns are the major source contributor to sulfate and nitrate. Volatile emission source and agriculture are the major contributors to ammonia; transport is the largest contributor to elemental carbon. Industrial processing, volatile emissions and mobile source are the most significant contributors to organic carbon. Results show that the Yangtze River Delta region should focus on the joint pollution control of industrial processing, combustion emissions, mobile source emissions, and fugitive dust. Regional transport of air pollution among the cities are prominent, and the implementation of regional joint prevention and control of air pollution will help to alleviate fine particulate matter concentrations under heavy pollution case significantly.

Effects of Adding Corn Dried Distiller Grains with Solubles (DDGS) to the Dairy Cow Diet and Effects of Bedding in Dairy Cow Slurry on Fugitive Methane Emissions.

PubMed

Massé, Daniel I; Jarret, Guillaume; Benchaar, Chaouki; Hassanat, Fadi

2014-12-09

The specific objectives of this experiment were to investigate the effects of adding 10% or 30% corn dried distillers grains with solubles (DDGS) to the dairy cow diet and the effects of bedding type (wood shavings, straw or peat moss) in dairy slurry on fugitive CH₄ emissions. The addition of DDGS10 to the dairy cow diet significantly increased (29%) the daily amount of fat excreted in slurry compared to the control diet. The inclusion of DDGS30 in the diet increased the daily amounts of excreted DM, volatile solids (VS), fat, neutral detergent fiber (NDF), acid detergent fiber (ADF) and hemicellulose by 18%, 18%, 70%, 30%, 15% and 53%, respectively, compared to the control diet. During the storage experiment, daily fugitive CH₄ emissions showed a significant increase of 15% (p < 0.05) for the slurry resulting from the corn DDGS30 diet. The addition of wood shavings and straw did not have a significant effect on daily fugitive CH₄ emissions relative to the control diet, whereas the addition of peat moss caused a significant increase of 27% (p < 0.05) in fugitive CH₄ emissions.

Monitoring fugitive methane and natural gas emissions, validation of measurement techniques.

NASA Astrophysics Data System (ADS)

Robinson, Rod; Innocenti, Fabrizio; Gardiner, Tom; Helmore, Jon; Finlayson, Andrew; Connor, Andy

2017-04-01

The detection and quantification of fugitive and diffuse methane emissions has become an increasing priority in recent years. As the requirements for routine measurement to support industry initiatives increase there is a growing requirement to assess and validate the performance of fugitive emission measurement technologies. For reported emissions traceability and comparability of measurements is important. This talk will present recent work addressing these needs. Differential Absorption Lidar (DIAL) is a laser based remote sensing technology, able to map the concentration of gases in the atmosphere and determine emission fluxes for fugitive emissions. A description of the technique and its application for determining fugitive emissions of methane from oil and gas operations and waste management sites will be given. As DIAL has gained acceptance as a powerful tool for the measurement and quantification of fugitive emissions, and given the rich data it produces, it is being increasingly used to assess and validate other measurement approaches. In addition, to support the validation of technologies, we have developed a portable controlled release facility able to simulate the emissions from area sources. This has been used to assess and validate techniques which are used to monitor emissions. The development and capabilities of the controlled release facility will be described. This talk will report on recent studies using DIAL and the controlled release facility to validate fugitive emission measurement techniques. This includes side by side comparisons of two DIAL systems, the application of both the DIAL technique and the controlled release facility in a major study carried out in 2015 by South Coast Air Quality Management District (SCAQMD) in which a number of optical techniques were assessed and the development of a prototype method validation approach for techniques used to measure methane emissions from shale gas sites. In conclusion the talk will provide an update on the current status in the development of a European Standard for the measurement of fugitive emissions of VOCs and the use of validation data in the standardisation process and discuss the application of this to methane measurement.

Fugitive Dust Emissions from Construction Haul Roads

DTIC Science & Technology

1977-02-01

38 APPENDIX A: Probe Analysis APPENDIX B: Soil Water Potential and Soil Psychrometers APPENDIX C: Complete Listing of Reduced Data...traveling through the 10-in. (25-cm) duct. Four soil psychrometers (see Appendix B) used to measure soil water poten- tial were buried in the wheel paths of...average slow speed test lasted approximately 8 hours. For com- par1qnn, an attempt was made to run all tests over the same range of soil psychrometer

Fugitive emission rates assessment of PM2.5 and PM10 from open storage piles in China

NASA Astrophysics Data System (ADS)

Cao, Yiqi; Liu, Tao; He, Jiao

2018-03-01

An assessment of the fugitive emission rates of PM2.5 and PM10 from an open static coal and mine storage piles. The experiment was conducted at a large union steel enterprises in the East China region to effectively control the fugitive particulate emissions pollution on daily work and extreme weather conditions. Wind tunnel experiments conducted on the surface of static storage piles, and it generated specific fugitive emission rates (SERs) at ground level of between ca.10-1 and ca.102 (mg/m2·s) for PM2.5 and between ca.101 and ca.103 (mg/m2·s) for PM10 under the u*(wind velocity) between ca.3.0 (m/s) and 10.0 (m/s). Research results show that SERs of different materials differ a lot. Material particulate that has lower surface moisture content generate higher SER and coal material generate higher SER than mine material. For material storage piles with good water infiltrating properties, aspersion is a very effective measure for control fugitive particulate emission.

Fugitive dust emissions from paved road travel in the Lake Tahoe basin.

PubMed

Zhu, Dongzi; Kuhns, Hampden D; Brown, Scott; Gillies, John A; Etyemezian, Vicken; Gertler, Alan W

2009-10-01

The clarity of water in Lake Tahoe has declined substantially over the past 40 yr. Causes of the degradation include nitrogen and phosphorous fertilization of the lake waters and increasing amounts of inorganic fine sediment that can scatter light. Atmospheric deposition is a major source of fine sediment. A year-round monitoring study of road dust emissions around the lake was completed in 2007 using the Testing Re-entrained Aerosol Kinetic Emissions from Roads (TRAKER) system developed at the Desert Research Institute (DRI). Results of this study found that, compared with the summer season, road dust emissions increased by a factor of 5 in winter, on average, and about a factor of 10 when traction control material was applied to the roads after snow events. For winter and summer, road dust emission factors (grams coarse particulate matter [PM10] per vehicle kilometer traveled [g/vkt]) showed a decreasing trend with the travel speed of the road. The highest emission factors were observed on very low traffic volume roads on the west side of the lake. These roads were composed of either a 3/8-in. gravel material or had degraded asphalt. The principle factors influencing road dust emissions in the basin are season, vehicle speed (or road type), road condition, road grade, and proximity to other high-emitting roads. Combined with a traffic volume model, an analysis of the total emissions from the road sections surveyed indicated that urban areas (in particular South Lake Tahoe) had the highest emitting roads in the basin.

Saccharide Composition in Fine and Coarse Particulate Matter and Soils in Central Arizona and Use of Saccharides as Molecular Markers for Source Apportionment

NASA Astrophysics Data System (ADS)

Jia, Y.; Clements, A.; Fraser, M.

2009-04-01

The desert southwestern United States routinely exceeds health-based standards for coarse particulate matter [1]. PM10 concentrations are high in both urban and rural areas and are believed to originate from fugitive dust emissions from agricultural fields and roads and soil erosion from the surrounding desert locations. Soil together with its associated biota contains a complex mixture of biogenic detritus, including plant detritus, airborne microbes comprised of bacteria, viruses, spores of lichens and fungi, small algae, and protozoan cysts [4][5], which can mostly become airborne when winds are strong enough and soil dry enough to be re-entrained into the atmosphere [3]. Other potential sources to PM10 may include primary biological aerosol particles (PBAPs), given a multitude of flower, grass, and fungal species that thrive in the Sonoran desert and actively release pollens and spores throughout the year [2]. However, because soil and fugitive dust is also believed to contain a large number of these biological particles and is considered as a secondary host of PBAPs [3] [4], the role and contribution of PBAPs as a direct ambient PM source in the desert southwest have not been clearly stated or investigated. In an effort to identify and assess the relative contribution of these and other major PM sources in the southwestern US region, and particularly to assess the contribution from soil and fugitive dust, a series of ambient PM samples and soil samples were collected in Higley, AZ, USA, a suburb of the Phoenix metropolitan area which has seen rapid urban sprawl onto agricultural lands. Because of their suggested ability to track biologically important organic materials from natural environment [4][6][7][8][9][10], saccharides were chosen as the key compounds to trace the release of soil dusts into the atmosphere, and to elucidate other major sources that contribute to the PM levels in this location in the arid southwestern US. To this end, saccharide compounds were analyzed in size segregated soil and ambient PM samples at Higley; intra- and inter- comparisons were made between the ambient PM and three types of soil dust samples (agricultural soil, native soil, road dust) based on the particle size (fine vs. coarse), seasonality, and relative composition of 12 saccharide compounds. Based on the ambient concentrations of major saccharides and a number of other specific compounds (including elemental and organic carbon, ions, metals, alkanes, organic acids, and polycyclic aromatic hydrocarbons) that are simultaneously resolved in Higley PM samples, a Positive Matrix Factorization (PMF) model was performed to determine the key contributors to PM10 and PM2.5 levels. Six distinct factors were isolated, with two factors dominated by the enrichment of saccharide compounds. There was not consistency between the source profiles of these two saccharide rich source factors with the saccharide composition of the local size-segregated soil samples, which implies that there may be other major sources contributing to ambient PM saccharides. One possible alternative is that PBAPs that are injected directly into the atmosphere instead of residing in the surface soil and being re-entrained through soil erosion or agricultural processing. To our knowledge, this study is the first of its kind to compare the saccharide composition between the fine and coarse fraction of different soils types in two seasons, and to relate the contribution from soil dust to ambient PM using saccharide species. REFERENCE [1] AirData: Access to Air Pollution data. [cited 2009 Jan 11, 2009]; Available from: http://www.epa.gov/air/data/index.html [2] Allergy and Asthma in the Southwestern United States. [cited 2009 Jan 11, 2009]; Available from: http://allergy.peds.arizona.edu/southwest/swpollen.html [3] Cox, C.S., Wathes, C.M., 1995. Bioaerosols Handbook, Lewis Publishers, NY [4] Simoneit, B.R.T., Elias, V.O., et al., 2004. "Sugars - Dominant water-soluble organic compounds in soils and characterization as tracers in atmospheric particulate matter", Environmental Science and Technology (38): 5939-5949. [5] Simoneit, B.R.T., Mazurek, M.A., 1981. "Air Pollution - the Organic-Components", Crc Critical Reviews in Environmental Control (11): 219-276. [6] Medeiros, P.M., Simoneit, B.R.T, 2007. "Analysis of sugars in environmental samples by gas chromatography-mass spectrometry", Jouranl of Chromatography A (1141): 271-278. [7] Rogge, W.F., Medeiros, P.M, et al., 2007. ‘Organic marker compounds in surface soils of crop fields from the San Joaquin Valley fugitive dust characterization study", Atmospheric Environment (41): 8183-8204. [8] Bauer, H., Claeys, M., et al., 2008. "Arabitol and mannitol as tracers for the quantification of airborne fungal spores", Atmospheric Environment (42): 588-593. [9] Elbert, W., Taylor, P.E., et al., 2007. "Contribution of fungi to primary biogenic aerosols in the atmosphere: wet and dry discharged spores, carbohydrates, and inorganic ions", Atmospheric Chemistry and Physics (7): 4569-4588. [10] Graham, B., Guyon, P., et al., 2003. "Organic compounds present in the natural Amazonian aerosol: Characterization by gas chromatography-mass spectrometry", Journal of Geophysical Research (108): 4766, doi:10.1029/2003JD003990.

Numerical Validation of a Near-Field Fugitive Dust Model for Vehicles Moving on Unpaved Surfaces

DTIC Science & Technology

2013-02-05

vehicles such as the numerical models developed at George mason University[2, 3]. Their model focused on represent- ing vehicles in a virtual...vehicles trav- eling on unpaved roads. In Proceedings of the conference on metroplitan physical environment (1977), G . Heisler and L. Herrington, Eds., pp...295–302. [5] Etyemezian, V., Gillies, J., Huhns, H., Nikolic, D., Watson, J., Ve- ranth, J., Laben, R., Seshadri, G ., and Gillette, D. Field testing

Design Analysis, Basin F Liquid Waste Disposal Facility, Rocky Mountain Arsenal, Commerce City, Colorado, FY81.

DTIC Science & Technology

1981-08-01

City were contacted concern- ing Building and Construction permits. No regulations apply since they do not have jurisdiction over RMA property. It may...Division. Mr. Dale advised that their agency’s regulations applied only to permanent pollution emitting sources. Mr. Plog thought that their "fugitive dust...processing, treat- ment, recovery, and disposal of hazardous waste. "Person" means an individual trust, firm, joint stock company , Federal Agency

Study on reinforcement of soil for suppressing fugitive dust by bio-cementitious material

NASA Astrophysics Data System (ADS)

Zhan, Qiwei; Qian, Chunxiang

2017-06-01

Microbial-induced reinforcement of soil, as a new green and environmental-friendly method, is being paid extensive attention to in that it has low cost, simple operation and rapid effects. In this research, reinforcement of soil for suppressing fugitive dust by bio-cementitious material was investigated. Soil cemented by bio-cementitious material had superior mechanical properties, such as hardness, compressive strength, microstructure, wind-erosion resistance, rainfall-erosion resistance and freeze-thaw resistance. The average hardness of sandy soil, floury soil and clay soil is 18.9 º, 25.2 º and 26.1 º, while average compressive strength of samples is 0.43 MPa, 0.54 MPa and 0.69 MPa, respectively; meanwhile, the average calcite content of samples is 6.85 %, 6.09 %, and 5.96 %, respectively. Compared with the original sandy soil, floury soil and clay soil, the porosity decreases by 38.5 %, 33.7 % and 29.2 %. When wind speed is 12 m/s, the mass loss of sandy soil, floury soil and clay soil cemented by bio-cementitious material are all less than 30 g/(m2·h). After three cycles of rainfall erosion of 2.5 mm/h, the mass loss are less than 25 g/(m2·h) and the compressive strength residual ratio are more than 98.0 %. Under 25 cycles of freeze-thaw, the mass loss ratio are less than 3.0 %.

A computational study of particulate emissions from an open pit quarry under neutral atmospheric conditions

NASA Astrophysics Data System (ADS)

Silvester, S. A.; Lowndes, I. S.; Hargreaves, D. M.

2009-12-01

The extraction of minerals from surface mines and quarries can produce significant fugitive dust emissions as a result of site activities such as blasting, road haulage, loading, crushing and stockpiling. If uncontrolled, these emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. The dispersion of pollutant emissions within the atmosphere is principally determined by the background wind systems characterized by the atmospheric boundary layer (ABL). This paper presents an overview of the construction and solution of a computational fluid dynamics (CFD) model to replicate the development of the internal ventilation regime within a surface quarry excavation due to the presence of a neutral ABL above this excavation. This model was then used to study the dispersion and deposition of fugitive mineral dust particles generated during rock blasting operations. The paths of the mineral particles were modelled using Lagrangian particle tracking. Particles of four size fractions were released from five blast locations for eight different wind directions. The study concluded that dependent on the location of the bench blast within the quarry and the direction of the wind, a mass fraction of between 0.3 and 0.6 of the emitted mineral particles was retained within the quarry. The retention was largest when the distance from the blast location to the downwind pit boundary was greatest.

A Methodology to Monitor Airborne PM10 Dust Particles Using a Small Unmanned Aerial Vehicle

PubMed Central

Alvarado, Miguel; Gonzalez, Felipe; Erskine, Peter; Cliff, David; Heuff, Darlene

2017-01-01

Throughout the process of coal extraction from surface mines, gases and particles are emitted in the form of fugitive emissions by activities such as hauling, blasting and transportation. As these emissions are diffuse in nature, estimations based upon emission factors and dispersion/advection equations need to be measured directly from the atmosphere. This paper expands upon previous research undertaken to develop a relative methodology to monitor PM10 dust particles produced by mining activities making use of small unmanned aerial vehicles (UAVs). A module sensor using a laser particle counter (OPC-N2 from Alphasense, Great Notley, Essex, UK) was tested. An aerodynamic flow experiment was undertaken to determine the position and length of a sampling probe of the sensing module. Flight tests were conducted in order to demonstrate that the sensor provided data which could be used to calculate the emission rate of a source. Emission rates are a critical variable for further predictive dispersion estimates. First, data collected by the airborne module was verified using a 5.0 m tower in which a TSI DRX 8533 (reference dust monitoring device, TSI, Shoreview, MN, USA) and a duplicate of the module sensor were installed. Second, concentration values collected by the monitoring module attached to the UAV (airborne module) obtaining a percentage error of 1.1%. Finally, emission rates from the source were calculated, with airborne data, obtaining errors as low as 1.2%. These errors are low and indicate that the readings collected with the airborne module are comparable to the TSI DRX and could be used to obtain specific emission factors from fugitive emissions for industrial activities. PMID:28216557

Large-Scale Land Development, Fugitive Dust, and Increased Coccidioidomycosis Incidence in the Antelope Valley of California, 1999-2014.

PubMed

Colson, Aaron J; Vredenburgh, Larry; Guevara, Ramon E; Rangel, Natalia P; Kloock, Carl T; Lauer, Antje

2017-06-01

Ongoing large-scale land development for renewable energy projects in the Antelope Valley, located in the Western Mojave Desert, has been blamed for increased fugitive dust emissions and coccidioidomycosis incidence among the general public in recent years. Soil samples were collected at six sites that were destined for solar farm construction and were analyzed for the presence of the soil-borne fungal pathogen Coccidioides immitis which is endemic to many areas of central and southern California. We used a modified culture-independent nested PCR approach to identify the pathogen in all soil samples and also compared the sampling sites in regard to soil physical and chemical parameters, degree of disturbance, and vegetation. Our results indicated the presence of C. immitis at four of the six sites, predominantly in non-disturbed soils of the Pond-Oban complex, which are characterized by an elevated pH and salt bush communities, but also in grassland characterized by different soil parameters and covered with native and non-native annuals. Overall, we were able to detect the pathogen in 40% of the soil samples (n = 42). Incidence of coccidioidomycosis in the Antelope Valley was positively correlated with land use and particulate matter in the air (PM10) (Pearson correlation coefficient >0.5). With the predicted population growth and ongoing large-scale disturbance of soil in the Antelope Valley in coming years, incidence of coccidioidomycosis will likely further increase if policy makers and land developers continue to ignore the risk of grading land without implementing long-term dust mitigation plans in Environmental Impact Reports.

Dust Generation Resulting from Desiccation of Playa Systems: Studies on Mono and Owens Lakes, California

NASA Astrophysics Data System (ADS)

Gill, Thomas Edward

1995-01-01

Playas, evaporites, and aeolian sediments frequently are linked components within the Earth system. Anthropogenic water diversions from terminal lakes form playas that release fugitive dust. These actions, documented worldwide, simulate aeolian processes activated during palaeoclimatic pluvial/interpluvial transitions, and have significant environmental impacts. Pluvial lakes Russell and Owens in North America's Great Basin preceded historic Mono and Owens Lakes, now desiccated by water diversions into dust-generating, evaporite -encrusted playas. Geochemical and hydrologic cycles acting on the Owens (Dry) Lake playa form three distinct crust types each year. Although initial dust production results from deflation of surface efflorescences after the playa dries, most aerosols are created by saltation abrasion of salt/silt/clay crusts at crust/ sand sheet contacts. The warm-season, clastic "cemented" crust is slowest to degrade into dust. If the playa surface is stabilized by an unbroken, non-efflorescent crust, dust formation is discouraged. When Mono Lake's surFace elevation does not exceed 1951 meters (6400 feet), similar processes will also generate dust from its saline lower playa. Six factors--related to wind, topography, groundwater, and sediments--control dust formation at both playas. These factors were combined into a statistical model relating suspended dust concentrations to playa/lake morphometry. The model shows the extent and severity of Mono Lake dust storms expands significantly below the surface level 6376 feet (1943.5 meters). X-ray diffraction analysis of Mono Basin soils, playa sediments, and aerosols demonstrates geochemical cycling of materials through land, air and water during Mono Lake's 1982 low stand. Soils and clastic playa sediments contain silicate minerals and tephra. Saline groundwater deposited calcite, halite, thenardite, gaylussite, burkeite and glauberite onto the lower playa. Aerosols contained silicate minerals (especially micas) and salts (including calcite, thenardite, gaylussite and halite). Playa-specific compounds were detected in the aerosol, even at a site not visually impacted by dust plumes. Anthropogenic mitigation may help alleviate playa dust storms. Reducing water diversions, legally mandated for Mono Lake, is not feasible everywhere. Most successful land rehabilitation schemes for playas have combined engineering (sand fences, flooding) and ecological (revegetation) techniques to mimic and accelerate natural processes; this is recommended for Owens (Dry) Lake.

Characterizing and Quantifying Emissions and Transport of Fugitive Dust Emissions Due to Department of Defense Activities

DTIC Science & Technology

2015-09-19

response to shear stress (τ, N m-2) induced by the PI-SWERL®, the viscosity of the fluid exerts a torque (N m-1) that eventually balances with τ. The...Engelbrecht et al. (2012) from CCSEM measurements, report that these silicate mineral particles are largely coated by a veneer of clay minerals and fine...content does not, by itself, contribute to the high emissions observed at YTC. The presence of high clay content can constrain the emissions by

Environmental Assessment for Tower Construction at the Brandywine Communication Receiver Site, Prince George’s County, Maryland

DTIC Science & Technology

2005-05-01

mobilization . • Place1nent of tower guy wires will be adjusted to avoid construction and disturbance to any wetlands or small tributaries through on...include combustion emissions (VOC, NOx, CO, SO2) and fugitive dust (PM10) from mobile heavy-duty diesel- and gasoline-powered equipment and soil...Pollutant Factors, Mobile Sources (AP 42). 4th Edition, U.S. Environmental Protection Agency, Ann Arbor, Michigan. Total estimated emissions for VOC and

Effects of Adding Corn Dried Distiller Grains with Solubles (DDGS) to the Dairy Cow Diet and Effects of Bedding in Dairy Cow Slurry on Fugitive Methane Emissions

PubMed Central

Massé, Daniel I.; Jarret, Guillaume; Benchaar, Chaouki; Hassanat, Fadi

2014-01-01

Simple Summary The objectives of this experiment were to investigate the effects of adding corn DDGS to the dairy cow diet as well as the bedding types (wood shavings, straw or peat moss) on manure fugitive CH4 emissions. The incorporation of DDGS in the diet has increased manure methane emission by 15% and the use of peat moss as bedding has increased manure methane emission by 27%. Abstract The specific objectives of this experiment were to investigate the effects of adding 10% or 30% corn dried distillers grains with solubles (DDGS) to the dairy cow diet and the effects of bedding type (wood shavings, straw or peat moss) in dairy slurry on fugitive CH4 emissions. The addition of DDGS10 to the dairy cow diet significantly increased (29%) the daily amount of fat excreted in slurry compared to the control diet. The inclusion of DDGS30 in the diet increased the daily amounts of excreted DM, volatile solids (VS), fat, neutral detergent fiber (NDF), acid detergent fiber (ADF) and hemicellulose by 18%, 18%, 70%, 30%, 15% and 53%, respectively, compared to the control diet. During the storage experiment, daily fugitive CH4 emissions showed a significant increase of 15% (p < 0.05) for the slurry resulting from the corn DDGS30 diet. The addition of wood shavings and straw did not have a significant effect on daily fugitive CH4 emissions relative to the control diet, whereas the addition of peat moss caused a significant increase of 27% (p < 0.05) in fugitive CH4 emissions. PMID:26479012

Tracing Sources and Contamination Assessments of Heavy Metals in Road and Foliar Dusts in a Typical Mining City, China

PubMed Central

Yang, Jie; Teng, Yanguo; Song, Liuting; Zuo, Rui

2016-01-01

Road and foliar dust samples from four land-use districts of Panzhihua City, a famous V-Ti magnetite production area of China, were collected to investigate the sources and distribution characteristics of 9 heavy metals (V, Pb, Cd, Cu, Zn, Ni, Cr, Fe, and Mn). The results suggest that foliar samples had smaller particle size and higher heavy metal contents than road dusts. The contamination assessments of heavy metals were as follows: Pb and V (significant enrichment) > Zn, Ni, Cr, Fe, and Mn (moderate enrichment) > Cd and Ni (minimal enrichment). Statistical analyses showed Pb, as the primary pollution element, originated from waste incineration and lead-fuel combustion. The sources of Zn, Ni, Cr, Fe, V, and Mn were fugitive dust and traffic activities. Potential origins of Cu were corrosion of alloys used in vehicle components, vehicle covers, or other metallic surfaces and materials. The sources of Cd were different from any other heavy metals. Traffic and industrial activities were the main anthropogenic origins of heavy metals in dusts of Panzhihua, and more attention should be paid to heavy metal pollution in agricultural area. PMID:27992518

Tracing Sources and Contamination Assessments of Heavy Metals in Road and Foliar Dusts in a Typical Mining City, China.

PubMed

Yang, Jie; Teng, Yanguo; Song, Liuting; Zuo, Rui

2016-01-01

Road and foliar dust samples from four land-use districts of Panzhihua City, a famous V-Ti magnetite production area of China, were collected to investigate the sources and distribution characteristics of 9 heavy metals (V, Pb, Cd, Cu, Zn, Ni, Cr, Fe, and Mn). The results suggest that foliar samples had smaller particle size and higher heavy metal contents than road dusts. The contamination assessments of heavy metals were as follows: Pb and V (significant enrichment) > Zn, Ni, Cr, Fe, and Mn (moderate enrichment) > Cd and Ni (minimal enrichment). Statistical analyses showed Pb, as the primary pollution element, originated from waste incineration and lead-fuel combustion. The sources of Zn, Ni, Cr, Fe, V, and Mn were fugitive dust and traffic activities. Potential origins of Cu were corrosion of alloys used in vehicle components, vehicle covers, or other metallic surfaces and materials. The sources of Cd were different from any other heavy metals. Traffic and industrial activities were the main anthropogenic origins of heavy metals in dusts of Panzhihua, and more attention should be paid to heavy metal pollution in agricultural area.

Sphagnum Moss as an Indicator of Contemporary Rates of Atmospheric Dust Deposition in the Athabasca Bituminous Sands Region.

PubMed

Mullan-Boudreau, Gillian; Belland, Rene; Devito, Kevin; Noernberg, Tommy; Pelletier, Rick; Shotyk, William

2017-07-05

Sphagnum moss was collected from ombrotrophic (rain-fed) peat bogs to quantify dust emissions from the open-pit mining and upgrading of Athabasca bituminous sands (ABS). A total of 30 bogs were sampled in the ABS region, and 5 were sampled in central Alberta. Ash was separated into the acid-insoluble ash (AIA) and acid-soluble ash (ASA) fractions using HCl. The AIA concentrations increase toward industry from 0.4 ± 0.5% to 4.7 ± 2.0% over a distance of 30 km; the control site at the Utikuma Region Study Area (URSA) yielded 0.29 ± 0.07% (n = 30). Mass accumulations rates showed similar spatial variation. The morphology and mineralogy of the AIA particles were studied using scanning electron microscopy and energy-dispersive X-ray analysis and the particle size distributions using optical methods. Particle size was more variable in moss closer to industry. Major ions in the ASA fraction showed elevated accumulation rates of Ca, K, Fe, Mg, P, and S, with P being up to 5 times greater in samples nearest industry compared to those in distal locations. Given that P has been regarded as the growth-limiting nutrient in bogs, fertilization of nutrient-poor ecosystems, such as these from fugitive emissions of dusts from open-pit mining, may have long-term ecological ramifications.

HIGHLIGHTS FROM TECHNICAL MANUAL ON HOOD SYSTEM CAPTURE OF PROCESS FUGITIVE PARTICULATE EMISSIONS

EPA Science Inventory

The paper discusses a technical manual whose emphasis is on the design and evaluation of actual hood systems used to control various fugitive particulate emission sources. Engineering analyses of the most important hood types are presented to provide a conceptual understanding of...

Inter-annual variability of wintertime PM2.5 chemical composition in Xi'an, China: Evidences of changing source emissions.

PubMed

Xu, Hongmei; Cao, Junji; Chow, Judith C; Huang, R-J; Shen, Zhenxing; Chen, L W Antony; Ho, Kin Fai; Watson, John G

2016-03-01

Chemical characteristics of PM2.5 in Xi'an in wintertime of 2006, 2008, and 2010 were investigated. Markers of OC2, EC1, and NO3(-)/SO4(2-) ratio were calculated to investigate the changes in PM2.5 emission sources over the 5-year period. Positive matrix factorization (PMF) model was used to identify and quantify the main sources of PM2.5 and their contributions. The results showed that coal combustion, motor vehicular emissions, fugitive dust, and secondary inorganic aerosol accounted for more than 80% of PM2.5 mass. The importance of these major sources to the PM2.5 mass varied yearly: coal combustion was the largest contributor (31.2% ± 5.2%), followed by secondary inorganic aerosol (20.9% ± 5.2%) and motor vehicular emissions (19.3% ± 4.8%) in 2006; the order was still coal combustion emissions (27.6% ± 3.4%), secondary inorganic aerosol (23.2% ± 6.9%), and motor vehicular emissions (20.9% ± 4.6%) in 2008; while coal combustion emission further decreased (24.1% ± 3.1%) with fugitive dust (19.4% ± 5.5%) increasing in 2010. The changes in PM2.5 chemical compositions and source contributions can be attributed to the social and economic developments in Xi'an, China, including energy structure adjustment, energy consumption, the expansion of civil vehicles, and the increase of urban construction activities. Copyright © 2015 Elsevier B.V. All rights reserved.

40 CFR 63.544 - Standards for process fugitive sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... National Emission Standards for Hazardous Air Pollutants from Secondary Lead Smelting § 63.544 Standards for process fugitive sources. (a) Each owner or operator of a secondary lead smelter shall control the...) Smelting furnace and dryer charging hoppers, chutes, and skip hoists; (2) Smelting furnace lead taps, and...

Fine particulate matter emissions inventories: comparisons of emissions estimates with observations from recent field programs.

PubMed

Simon, Heather; Allen, David T; Wittig, Ann E

2008-02-01

Emissions inventories of fine particulate matter (PM2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5-20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM2.s are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.

Using Si depletion in aerosol to identify the sources of crustal dust in two Chinese megacities

NASA Astrophysics Data System (ADS)

Zhao, Qing; He, Kebin; Rahn, Kenneth A.; Ma, Yongliang; Yang, Fumo; Duan, Fengkui

2010-07-01

Depletion of Si in transported dust has been recognized for many years. It can be used to distinguish between transported and local dust in cities, although it rarely has been. Here we use the variations of the Si/Al ratio in 15 months of continuous PM 2.5 samples at Beijing (northern China) and Chongqing (southwestern China) to reveal the seasonal patterns of their dust sources. For both cities, peaks of concentration for Si and Al in PM 2.5 corresponded with minima of Si/Al, and could often be linked to pulsed air flow from deserts to the northwest. With significant depletion (up to 80%) and homogeneous distribution at urban and rural sites, Si/Al showed a clear seasonal evolution, which decreased from spring to summer, increased from fall to winter, and collapsed during Chinese Spring Festival, indicating the dominance of transported dust, local fugitive dust and firework influence, respectively. The low ratios implied that desert dust is a common source during spring at Chongqing, whereas its presence during cold season at Beijing was also more frequent than expected. Failing to recognize the depletion of Si may lead to an overestimate of desert dust by 15%-65% when using the average abundance of Al in crust (6%-8%), as in previous studies. The difference in Si/Al ratio between local and transported dust implies that >60% of the dust at Beijing came from outside the city during the springs of 2004-2006. This result can help resolve the contradictory findings on this topic that have been presented earlier.

Superfund Record of Decision (EPA Region 8): Anaconda Smelter Site, Mill Creek, Montana (first remedial action), October 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-10-02

The 160-acre community of Mill Creek is located in Deerlodge County, Montana, immediately adjacent to the Anaconda Smelter NPL site. The community of Mill Creek has been contaminated for over 100 years with smelter emissions, fugitive emissions of flu dust at the smelter, and continued fugitive emissions emanating from adjacent highly contaminated soils. Settled flue emissions in the community of Mill Creek, from the now-defunct copper-smelting operation, contain arsenic, cadmium, and lead. Environmental siting of the community and biological testing of pre-school children, led EPA to conclude that contamination in the Mill Creek area poses an imminent and substantial endangermentmore » to the health of individuals residing there. The primary contaminant of concern at this site is arsenic. Cadmium and lead are secondary contaminants of concern. The selected remedial action for the site includes: permanent relocation of all residents (8 homes) with temporary erosional stabilization of disturbed areas by establishing and maintaining a vegetative cover; demolition, consolidation, and storage.« less

[Influence of traffic restriction on road and construction fugitive dust].

PubMed

Tian, Gang; Li, Gang; Qin, Jian-Ping; Fan, Shou-Bin; Huang, Yu-Hu; Nie, Lei

2009-05-15

By monitoring the road and construction dust fall continuously during the "Good Luck Beijing" sport events, the reduction of road and construction dust fall caused by traffic restriction was studied. The contribution rate of road and construction dust to particulate matter of Beijing atmosphere environment, and the emission ratio of it to total local PM10 emission were analyzed. The results show that the traffic restriction reduces road and construction dust fall significantly. The dust fall average value of ring roads was 0.27 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 0.81 and 0.59 g x (m2 x d)(-1) 1 month and 7 days before. The dust fall average value of major arterial and minor arterial was 0.21 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 0.54 and 0.58 g x (m2 x d)(-1) 1 month and 7 days before. The roads emission reduced 60%-70% compared with before traffic restriction. The dust fall average values of civil architecture and utility architecture were 0.61 and 1.06 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 1.15 and 1.55 g x (m2 x d)(-1) 20 days before. The construction dust reduced 30%-47% compared with 20 days before traffic restriction. Road and construction dust emission are the main source of atmosphere particulate matter in Beijing, and its contribution to ambient PM10 concentration is 21%-36%. PM10 emitted from roads and constructions account for 42%-72% and 30%-51% of local emission while the local PM10 account for 50% and 70% of the total emission.

Philadelphia gas works medium-Btu coal gasification project: environmental assessment. [GKT supplied by Krupp-Koppers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-12-01

The coal gasification plant will occupy a 43-acre site, known as the Riverside Site, located along the Delaware River next to Port Richmond between the Betsy Ross and Benjamin Franklin Bridges. The cleared site was previously used for industrial purposes and has a G-2 industrial zoning. Adverse impacts during the construction phase of the project are not expected to be significantly different than those occurring during any major industrial construction project. During operation of the coal gasification facility, specific mitigative measures have been designed into the facility to avoid adverse environmental impacts wherever possible. In addition to these extensive engineeringmore » safeguards, elaborate monitoring and control instrumentation shall be used. The GKT entrained bed, oxygen-blown gasification process provided by Krupp/Koppers was selected because it is a commercially proven system and because of its positive environmental characteristics such as its ability to gasify many coal types and the fact that it does not produce tars, phenols, or ammonia. During gasification of the coal, pollutants such as heavy metals in the coal are concentrated into the slag and ash. None of these pollutants are found in the product gas. The facility will produce 250 tpd of non-hazardous slag and fly ash. The combined slag and fly ash will occupy 347 cubic yards per day of landfill volume. Available haulers and landfills have been identified.A sophisticated health and safety program will include appropriate monitoring instruments for CO, H/sub 2/, H/sub 2/S, polynuclear aromatic hydrocarbons, organic compounds, and coal dust. Air emissions from operation of the coal gasification plant are not considered significant. Dust control systems have been designed into the facility to minimize fugitive dust emissions.« less

Determination of water-soluble elements in PM2.5, PM10, and PM2.5-10 collected in the surroundings of power plants

NASA Astrophysics Data System (ADS)

Zajusz-Zubek, Elwira; Mainka, Anna; Kaczmarek, Konrad

2018-01-01

The analysis reported in this study was performed to characterize the concentrations and water-soluble content of trace elements (As, Cd, Co, Cr, Hg, Mn, Ni, Pb, Sb and Se) in PM2.5, PM10 and PM2.5-10 samples collected in the surroundings of power plants in southern Poland. The solubility of trace elements bound to PM2.5 and PM10 was higher than for PM2.5-10, and in most cases, significant differences were revealed in the relative percentage concentrations of the water-soluble fractions. The occurrence of Cd, Cr, Mn, Ni, Pb and Se in first PCA (Principal Component Analysis) factor (PC1) - indicate coal combustion processes as the potential source of these elements. Other factors indicate two further anthropogenic sources: the resuspension of road dust due to vehicular activities and waste burning in domestic sources - factor (PC2), and, soil dust sources affected by fugitive dust from the mining processes and unpaved roads, as well as transportation and deposition of coal -factor (PC3).

Fort Carson Fugitive Dust Generation and Transport Study: Lessons Learned.

DTIC Science & Technology

1981-11-01

15 99.9 024.9 1309 9/16 99.9 058.6 1307 9/17 99.9 029.2 1361 9/18 99.9 058.8 1353 9/19 99.9 030.2 1352 9/20 99.9 019.4 1347 9/21 99.9 036.6 1348 9/22...0413 4/25 99.9 059.7 0412 4/26 99.9 039.3 0417 4/27 99.9 042.0 0423 4/28 99.9 023.4 0428 4/29 99.9 007.8 0425 4/30 007.8 0425 Geometric Mean - 25.561

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

NASA Astrophysics Data System (ADS)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press), authors show how to apply in ME-2 this knowledge to obtain a quantitative assessment of this source. The achievement of this objective permitted to show how is possible to improve a basic solution of PMF2 basing on an extended model. Results show that road dust resuspension accounted for 6.7 µg/m3 (16%) in PM10, 2.2 µg/m3 (8%) of PM2.5 and 0.3 µg/m3 (1%) of PM1, revealing that fugitive emissions were responsible of the 36%, 18% and 2% of total traffic emissions respectively in PM10, PM2.5 and PM1. Acknowledments: This work was funded by the Spanish Ministry of Science and Innovation (GRACCIE-SCD2007-00067)

Advancing Knowledge on Fugitive Natural Gas from Energy Resource Development at a Controlled Release Field Observatory

NASA Astrophysics Data System (ADS)

Cahill, A. G.; Chao, J.; Forde, O.; Prystupa, E.; Mayer, K. U.; Black, T. A.; Tannant, D. D.; Crowe, S.; Hallam, S.; Mayer, B.; Lauer, R. M.; van Geloven, C.; Welch, L. A.; Salas, C.; Levson, V.; Risk, D. A.; Beckie, R. D.

2017-12-01

Fugitive gas, comprised primarily of methane, can be unintentionally released from upstream oil and gas development either at surface from leaky infrastructure or in the subsurface through failure of energy well bore integrity. For the latter, defective cement seals around energy well casings may permit buoyant flow of natural gas from the deeper subsurface towards shallow aquifers, the ground surface and potentially into the atmosphere. Concerns associated with fugitive gas release at surface and in the subsurface include contributions to greenhouse gas emissions, subsurface migration leading to accumulation in nearby infrastructure and impacts to groundwater quality. Current knowledge of the extent of fugitive gas leakage including how to best detect and monitor over time, and particularly its migration and fate in the subsurface, is incomplete. We have established an experimental field observatory for evaluating fugitive gas leakage in an area of historic and ongoing hydrocarbon resource development within the Montney Resource Play of the Western Canadian Sedimentary Basin, British Columbia, Canada. Natural gas will be intentionally released at surface and up to 25 m below surface at various rates and durations. Resulting migration patterns and impacts will be evaluated through examination of the geology, hydrogeology, hydro-geochemistry, isotope geochemistry, hydro-geophysics, vadose zone and soil gas processes, microbiology, and atmospheric conditions. The use of unmanned aerial vehicles and remote sensors for monitoring and detection of methane will also be assessed for suitability as environmental monitoring tools. Here we outline the experimental design and describe initial research conducted to develop a detailed site conceptual model of the field observatory. Subsequently, results attained from pilot surface and sub-surface controlled natural gas releases conducted in late summer 2017 will be presented as well as results of numerical modelling conducted to plan methane release experiments in 2018 and onwards. This research will create knowledge which informs strategies to detect and monitor fugitive gas fluxes at the surface and in groundwater; as well as guide associated regulatory and technical policies.

No short-term cytogenetic consequences of Hungarian red mud catastrophe.

PubMed

Gundy, Sarolta; Farkas, Gyöngyi; Székely, Gábor; Kásler, Miklós

2013-01-01

Red mud is an industrial waste produced in the process of alumina extraction from bauxite with concentrated NaOH. When the red mud-containing reservoir collapsed in Ajka Alumina Plant Hungary in October 2010, the most serious immediate effects were caused by the high alkalinity (pH ≥ 13) of the flood. Many persons suffered burn-like damage to tissues and contact with caustic desiccated ultra-fine dust with traces of toxic metals also caused irritation of upper respiratory tract and eyes. This catastrophe was unique from the point of view of genotoxic effects as well. Therefore cytogenetic examinations were carried out on inhabitants, either with burns (17 persons) or on those inhaling desiccated caustic dust (42 persons). Chromosomal aberration (CA) analysis and bleomycin (BLM)-sensitivity assays, as possible markers of effects, were studied in peripheral blood lymphocytes of persons within 4-6 weeks following the catastrophe. Controls were matched for age, sex and smoking habits, and also places of residence with different constituents of air pollution either from rural (59 persons), or from urban environments (59 persons). Neither spontaneous rate of CAs (1.47% vs. 1.69%) nor BLM-induced in vitro chromosomal breakage (0.79 vs. 0.83 break/cell) showed elevated rates when cytogenetic biomarkers of genotoxicity were compared between controls and exposed persons. Time spent in cleaning did not affect cytogenetic changes either (R(2) = 0.04). BLM-induced mutagen sensitivity was similar in exposed and control persons (27.1% vs. 30.5%). It seems that the red mud exposure does not appear to pose an immediate genotoxic hazard on residents when measured with cytogenetic methods. We recommend, however, that those involved in clean-up activities should be followed closely not only for overall health, but also for further genotoxic risk assessment, because the long-term hazards of ultra-fine fugitive dust particles with alkalinity of residual NaOH in red mud are still unknown.

Impairment of soil health due to fly ash-fugitive dust deposition from coal-fired thermal power plants.

PubMed

Raja, R; Nayak, A K; Shukla, A K; Rao, K S; Gautam, Priyanka; Lal, B; Tripathi, R; Shahid, M; Panda, B B; Kumar, A; Bhattacharyya, P; Bardhan, G; Gupta, S; Patra, D K

2015-11-01

Thermal power stations apart from being source of energy supply are causing soil pollution leading to its degradation in fertility and contamination. Fine particle and trace element emissions from energy production in coal-fired thermal power plants are associated with significant adverse effects on human, animal, and soil health. Contamination of soil with cadmium, nickel, copper, lead, arsenic, chromium, and zinc can be a primary route of human exposure to these potentially toxic elements. The environmental evaluation of surrounding soil of thermal power plants in Odisha may serve a model study to get the insight into hazards they are causing. The study investigates the impact of fly ash-fugitive dust (FAFD) deposition from coal-fired thermal power plant emissions on soil properties including trace element concentration, pH, and soil enzymatic activities. Higher FAFD deposition was found in the close proximity of power plants, which led to high pH and greater accumulation of heavy metals. Among the three power plants, in the vicinity of NALCO, higher concentrations of soil organic carbon and nitrogen was observed whereas, higher phosphorus content was recorded in the proximity of NTPC. Multivariate statistical analysis of different variables and their association indicated that FAFD deposition and soil properties were influenced by the source of emissions and distance from source of emission. Pollution in soil profiles and high risk areas were detected and visualized using surface maps based on Kriging interpolation. The concentrations of chromium and arsenic were higher in the soil where FAFD deposition was more. Observance of relatively high concentration of heavy metals like cadmium, lead, nickel, and arsenic and a low concentration of enzymatic activity in proximity to the emission source indicated a possible link with anthropogenic emissions.

Chemical characterization and receptor modeling of PM10 in the surroundings of the opencast lignite mines of Western Macedonia, Greece.

PubMed

Samara, Constantini; Argyropoulos, George; Grigoratos, Theodoros; Kouras, Αthanasios; Manoli, Εvangelia; Andreadou, Symela; Pavloudakis, Fragkiskos; Sahanidis, Chariton

2018-05-01

The Western Macedonian Lignite Center (WMLC) in northwestern Greece is the major lignite center in the Balkans feeding four major power plants of total power exceeding 4 GW. Concentrations of PM 10 (i.e., particulate matters with diameters ≤10 μm) are the main concern in the region, and the high levels observed are often attributed to the activities related to power generation. In this study, the contribution of fugitive dust emissions from the opencast lignite mines to the ambient levels of PM 10 in the surroundings was estimated by performing chemical mass balance (CMB) receptor modeling. For this purpose, PM 10 samples were concurrently collected at four receptor sites located in the periphery of the mine area during the cold and the warm periods of the year (November-December 2011 and August-September 2012), and analyzed for a total of 26 macro- and trace elements and ionic species (sulfate, nitrate, chloride). The robotic chemical mass balance (RCMB) model was employed for source identification/apportionment of PM 10 at each receptor site using as inputs the ambient concentrations and the chemical profiles of various sources including the major mine operations, the fly ash escaping the electrostatic filters of the power plants, and other primary and secondary sources. Mean measured PM 10 concentrations at the different sites ranged from 38 to 72 μg m -3 . The estimated total contribution of mines ranged between 9 and 22% in the cold period increasing to 36-42% in the dry warm period. Other significant sources were vehicular traffic, biomass burning, and secondary sulfate and nitrate aerosol. These results imply that more efficient measures to prevent and suppress fugitive dust emissions from the mines are needed.

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Rule for limiting fugitive particulate matter emissions. (a) What is the purpose of this section? This section limits the amount of fugitive particulate matter that may be emitted from certain air pollution... source of fugitive particulate matter emissions. (c) What is exempted from this section? This section...

Size-Resolved Dust and Aerosol Contaminants Associated with Copper and Lead Smelting Emissions: Implications for Emissions Management and Human Health

PubMed Central

Csavina, Janae; Taylor, Mark P.; Félix, Omar; Rine, Kyle P.; Sáez, A. Eduardo; Betterton, Eric A.

2014-01-01

Mining operations, including crushing, grinding, smelting, refining, and tailings management, are a significant source of airborne metal and metalloid contaminants such as As, Pb and other potentially toxic elements. In this work, we show that size-resolved concentrations of As and Pb generally follow a bimodal distribution with the majority of contaminants in the fine size fraction (< 1 μm) around mining activities that include smelting operations at various sites in Australia and Arizona. This evidence suggests that contaminated fine particles (< 1 μm) are the result of vapor condensation and coagulation from smelting operations while coarse particles are most likely the result of windblown dust from contaminated mine tailings and fugitive emissions from crushing and grinding activities. These results on the size distribution of contaminants around mining operations are reported to demonstrate the ubiquitous nature of this phenomenon so that more effective emissions management and practices that minimize health risks associated with metal extraction and processing can be developed. PMID:24995641

Wildlife conservation and solar energy development in the Desert Southwest, United States

USGS Publications Warehouse

Lovich, Jeffrey E.; Ennen, Josua R.

2011-01-01

Large areas of public land are currently being permitted or evaluated for utility-scale solar energy development (USSED) in the southwestern United States, including areas with high biodiversity and protected species. However, peer-reviewed studies of the effects of USSED on wildlife are lacking. The potential effects of the construction and the eventual decommissioning of solar energy facilities include the direct mortality of wildlife; environmental impacts of fugitive dust and dust suppressants; destruction and modification of habitat, including the impacts of roads; and off-site impacts related to construction material acquisition, processing, and transportation. The potential effects of the operation and maintenance of the facilities include habitat fragmentation and barriers to gene flow, increased noise, electromagnetic field generation, microclimate alteration, pollution, water consumption, and fire. Facility design effects, the efficacy of site-selection criteria, and the cumulative effects of USSED on regional wildlife populations are unknown. Currently available peer-reviewed data are insufficient to allow a rigorous assessment of the impact of USSED on wildlife.

Chemical characterization of sanding dust and methylene chloride usage in automotive refinishing: implications for occupational and environmental health.

PubMed

Enander, Richard T; Gute, David M; Cohen, Howard J; Brown, Linfield C; Desmaris, Anne Marie C; Missaghian, Richard

2002-01-01

Surface preparation activities conducted during automotive refinishing present several potential human health and environmental risks. This study examines the chemical composition of vehicle sanding dust and the prevalence of methylene chloride use as a basis for evaluating potential chemical exposures in the work environment, fugitive environmental releases, and take-home toxics. This article reports on the findings of (1) a statewide technology and work practices survey of 353 licensed auto body shops and (2) laboratory analyses of sanding dust representing more than 200 vehicles, 10 commercial body filler compounds, and work shirts worn during vehicle sanding while using nonventilated equipment. Survey data revealed that the majority of shops (78%) do not use ventilated sanding equipment, that most workers (55%) take their work clothes and shoes home at the end of the workday, and that 17% of the respondents used a methylene chloride-based paint stripper as an adjunct to mechanical sanding. Laboratory results showed that Pb, As, Cr, Mn, and Ni were present in the sanding dust at every facility tested. Lead concentrations in sanding dust were found to be highest at facilities that performed complete vehicle refinishing (range 770 to 7300 ppm) and at a collision repair shop that used a high-lead content body filler compound (1800 ppm). Hexavalent chromium also was found in two vocational high school paint dust samples at concentrations of 54 and 710 ppm. When total lead and chromium concentrations reached 7300 and 2300 ppm, respectively, facility sanding dust samples failed the U.S. Environmental Protection Agency's Toxicity Characteristic Leaching Procedure for hazardous waste. Metals found in the sanding dust also were present on the work shirts of technicians-ranging from 0.06 (Cd) to 81 (Mg) microg/inch2 of cloth-who sanded on paint without ventilated equipment. Results suggest that sanding dust and methylene chloride paint strippers used in vehicle resurfacing operations pose a potential hazard to human health and the environment.

Airborne concentrations of methylene diphenyl diisocyanate (MDI) in North American wood mills during the manufacturing of oriented strand board (OSB).

PubMed

Karoly, William J; Flatley, John J; Stevenson, Ralph D; Bowers, John D

2004-12-01

Air monitoring data were collected from industrial hygiene surveys over an 8-year period in oriented strand board (OSB) mills. Personal samples were taken to evaluate potential employee exposures to MDI. Area samples were taken to determine the effectiveness of control measures used in the mills to prevent fugitive emissions of wood dust, MDI, and MDI-coated wood dust from the OSB manufacturing process. Personal sampling results (578 samples covering 11 different job categories) ranged from 0.0002-0.524 mg/m3, with a GM = 0.001 and GSD = 3.71. Area sampling results (1657 samples covering 14 stationary locations in the mills) ranged from 0.0002-2.5 mg/m3, with a GM = 0.004 and GSD = 5.52. The statistical range of the data suggests high variability. While exposures to MDI above the established limits (0.051 mg/m3, 8-hour time-weighted average, 0.2 mg/m3, ceiling) can and do occur when engineering controls are not maintained and/or proper work practices and personal protective equipment are not followed/used for certain high exposure potential tasks, the data indicate that over 97% of the personal and 92% of the area sampling results are less than 0.051 mg/m3. Wipe testing was performed to determine the presence of removable, unreacted diisocyanates (NCO functional groups)from various surfaces. Positive results were found in about 13% of the wipe tests on surfaces confined to the blender, forming line, and hopper deck process areas.

The Yucca Mountain Project prototype air-coring test, U12g tunnel, Nevada test site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ray, J.M.; Newsom, J.C.

1994-12-01

The Prototype Air-Coring Test was conducted at the Nevada Test Site (NTS) G-Tunnel facility to evaluate standard coring techniques, modified slightly for air circulation, for use in testing at a prospective nuclear waste repository at Yucca Mountain, Nevada. Air-coring technology allows sampling of subsurface lithology with minimal perturbation to ambient characteristic such as that required for exploratory holes near aquifers, environmental applications, and site characterization work. Two horizontal holes were cored, one 50 ft long and the other 150 ft long, in densely welded fractured tuff to simulate the difficult drilling conditions anticipated at Yucca Mountain. Drilling data from sevenmore » holes on three other prototype tests in nonwelded tuff were also collected for comparison. The test was used to establish preliminary standards of performance for drilling and dust collection equipment and to assess procedural efficiencies. The Longyear-38 drill achieved 97% recovery for HQ-size core (-2.5 in.), and the Atlas Copco dust collector (DCT-90) captured 1500 lb of fugitive dust in a mine environment with only minor modifications. Average hole production rates were 6-8 ft per 6-h shift in welded tuff and almost 20 ft per shift on deeper holes in nonwelded tuff. Lexan liners were successfully used to encapsulate core samples during the coring process and protect core properties effectively. The Prototype Air-Coring Test demonstrated that horizontal air coring in fractured welded tuff (to at least 150 ft) can be safely accomplished by proper selection, integration, and minor modification of standard drilling equipment, using appropriate procedures and engineering controls. The test also indicated that rig logistics, equipment, and methods need improvement before attempting a large-scale dry drilling program at Yucca Mountain.« less

75 FR 48880 - Approval and Promulgation of Gila River Indian Community's Tribal Implementation Plan

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-12

...The Environmental Protection Agency (EPA) proposes to approve the Gila River Indian Community's (GRIC or the Tribe) Tribal Implementation Plan (TIP) under the Clean Air Act (CAA) to regulate air pollution within the exterior boundaries of the Tribe's reservation. The proposed TIP is one of four CAA regulatory programs that comprise the Tribe's Air Quality Management Plan (AQMP). EPA approved the Tribe for treatment in the same manner as a State (Treatment as State or TAS) for purposes of administering the AQMP and other CAA authorities on October 21, 2009. In this action we propose to act only on those portions of the AQMP that constitute a TIP containing severable elements of an implementation plan under CAA section 110(a). The proposed TIP includes general and emergency authorities, ambient air quality standards, permitting requirements for minor sources of air pollution, enforcement authorities, procedures for administrative appeals and judicial review in Tribal court, requirements for area sources of fugitive dust and fugitive particulate matter, general prohibitory rules, and source category-specific emission limitations. The purpose of the proposed TIP is to implement, maintain, and enforce the National Ambient Air Quality Standards (NAAQS) in the GRIC reservation. The intended effect of today's proposed action is to make the GRIC TIP federally enforceable.

Concentrations and bioaccessibility of metals in vegetation and dust near a mining haul road, Cape Krusenstern National Monument, Alaska

USGS Publications Warehouse

Brumbaugh, William G.; Morman, Suzette A.; May, Thomas W.

2011-01-01

Vegetation, sub-surface peat, and road dust were sampled near the Delong Mountain Transportation System (DMTS) haul road in northwest Alaska in 2005-2006 to document aluminum, barium, cadmium, lead, and zinc concentrations, and to evaluate bioaccessibility of these metals. The DMTS haul road is the transport corridor between Red Dog Mine (a large-scale, lead-zinc mine and mill) and the coastal shipping port, and it traverses National Park Service lands. Compared to reference locations, total metal concentrations in four types of vegetation (birch, cranberry, and willow leaves, and cotton grass blades/stalks) collected 25 m from the haul road were enriched on average by factors of 3.5 for zinc, 8.0 for barium, 20 for cadmium, and 150 for lead. Triple rinsing of vegetation with a water/methanol mixture reduced metals concentrations by at most 50%, and cadmium and zinc concentrations were least affected by rinsing. Cadmium and zinc bioaccessibility was greater in vegetation (50% to 100%) than in dust (15% to 20%); whereas the opposite pattern was observed for lead bioaccessibility (<30% in vegetation; 50% in dust). Barium exhibited low-to-intermediate bioaccessibility in dust and vegetation (20% to 40%), whereas aluminum bioaccessibility was relatively low (<6%) in all sample types. Our reconnaissance-level study indicates that clean-up and improvements in lead/zinc concentrate transfer activities have been effective; however, as of 2006, metal dispersion from past and/or present releases of fugitive dusts along the DMTS road still may have been contributing to elevated metals in surface vegetation. Vegetation was most enriched in lead, but because bioaccessibility of cadmium was greater, any potential risks to animals that forage near the haul road might be equally important for both of these metals.

High resolution spatial and temporal evolution of dissolved gases in groundwater during a controlled natural gas release experiment.

PubMed

Cahill, Aaron G; Parker, Beth L; Mayer, Bernhard; Mayer, K Ulrich; Cherry, John A

2018-05-01

Fugitive gas comprised primarily of methane (CH 4 ) with traces of ethane and propane (collectively termed C 1-3 ) may negatively impact shallow groundwater when unintentionally released from oil and natural gas wells. Currently, knowledge of fugitive gas migration, subsurface source identification and oxidation potential in groundwater is limited. To advance understanding, a controlled release experiment was performed at the Borden Research Aquifer, Canada, whereby 51m 3 of natural gas was injected into an unconfined sand aquifer over 72days with dissolved gases monitored over 323days. During active gas injection, a dispersed plume of dissolved C 1-3 evolved in a depth discrete and spatially complex manner. Evolution of the dissolved gas plume was driven by free-phase gas migration controlled by small-scale sediment layering and anisotropy. Upon cessation of gas injection, C 1-3 concentrations increased to the greatest levels observed, particularly at 2 and 6m depths, reaching up to 31.5, 1.5 and 0.1mg/L respectively before stabilizing and persisting. At no time did groundwater become fully saturated with natural gas at the scale of sampling undertaken. Throughout the experiment the isotopic composition of injected methane (δ 13 C of -42.2‰) and the wetness parameter (i.e. the ratio of C 1 to C 2+ ) constituted excellent tracers for the presence of fugitive gas at concentrations >2mg/L. At discrete times C 1-3 concentrations varied by up to 4 orders of magnitude over 8m of aquifer thickness (e.g. from <0.01 to 30mg/L for CH 4 ), while some groundwater samples lacked evidence of fugitive gas, despite being within 10m of the injection zone. Meanwhile, carbon isotope ratios of dissolved CH 4 showed no evidence of oxidation. Our results show that while impacts to aquifers from a fugitive gas event are readily detectable at discrete depths, they are spatially and temporally variable and dissolved methane has propensity to persist. Copyright © 2017 Elsevier B.V. All rights reserved.

Assessing fugitive emissions of CH4 from high-pressure gas pipelines

NASA Astrophysics Data System (ADS)

Worrall, Fred; Boothroyd, Ian; Davies, Richard

2017-04-01

The impact of unconventional natural gas production using hydraulic fracturing methods from shale gas basins has been assessed using life-cycle emissions inventories, covering areas such as pre-production, production and transmission processes. The transmission of natural gas from well pad to processing plants and its transport to domestic sites is an important source of fugitive CH4, yet emissions factors and fluxes from transmission processes are often based upon ver out of date measurements. It is important to determine accurate measurements of natural gas losses when compressed and transported between production and processing facilities so as to accurately determine life-cycle CH4 emissions. This study considers CH4 emissions from the UK National Transmission System (NTS) of high pressure natural gas pipelines. Mobile surveys of CH4 emissions using a Picarro Surveyor cavity-ring-down spectrometer were conducted across four areas in the UK, with routes bisecting high pressure pipelines and separate control routes away from the pipelines. A manual survey of soil gas measurements was also conducted along one of the high pressure pipelines using a tunable diode laser. When wind adjusted 92 km of high pressure pipeline and 72 km of control route were drive over a 10 day period. When wind and distance adjusted CH4 fluxes were significantly greater on routes with a pipeline than those without. The smallest leak detectable was 3% above ambient (1.03 relative concentration) with any leaks below 3% above ambient assumed ambient. The number of leaks detected along the pipelines correlate to the estimated length of pipe joints, inferring that there are constant fugitive CH4 emissions from these joints. When scaled up to the UK's National Transmission System pipeline length of 7600 km gives a fugitive CH4 flux of 4700 ± 2864 kt CH4/yr - this fugitive emission from high pressure pipelines is 0.016% of the annual gas supply.

Emissions from vehicles, tailpipe and vehicle re-entrained road dust

NASA Astrophysics Data System (ADS)

Zhu, Dongzi

Emissions from transportation are some of the largest sources of urban air pollution. Transportation emissions originate from both the engine-through combustion processes and non-tailpipe re-suspended road dust emissions induced by vehicle travel on unpaved and paved roads. Gaseous and particulate emissions from transportation sources have negative impacts on human health, visibility and may influence the global radiation balance. Fugitive dust emissions originating from vehicle travel on paved and unpaved roads constitute a significant fraction of the PM10 in many areas of the western US impacting their attainment status of National Ambient Air Quality Standards. The research used three novel instrument platforms developed at the Desert Research Institute. The In-Plume Emissions Test Stand (IPETS) was designed to provide characterization of exhaust emissions from in-use individual vehicles or engines by analyzing air as close as 1 m from the exhaust port. Real-world emission factors can be quantified by in-plume measurements and provide more realistic measures for emission inventories, source modeling, and receptor modeling than certification measurements. The Testing Re-entrained Aerosol Kinetic Emissions from Roads (TRAKER) provides an effective alternate approach to the EPA AP-42 road dust emissions estimation techniques by sampling 1000s of km of roads versus isolated 3 m sections. The Portable Deposition Monitoring Platform (PDMP incorporates PM and meteorological instruments to characterize the downwind change in particle concentrations to define depositional losses in different environments. The research outcome provides important knowledge for understanding diesel engine emissions, road dust emissions and aerosol deposition process near road sources.

Assessing fugitive emissions of CH4 from high-pressure gas pipelines in the UK

NASA Astrophysics Data System (ADS)

Clancy, S.; Worrall, F.; Davies, R. J.; Almond, S.; Boothroyd, I.

2016-12-01

Concern over the greenhouse gas impact of the exploitation of unconventional natural gas from shale deposits has caused a spotlight to be shone on to the entire hydrocarbon industry. Numerous studies have developed life-cycle emissions inventories to assess the impact that hydraulic fracturing has upon greenhouse gas emissions. Incorporated within life-cycle assessments are transmission and distribution losses, including infrastructure such as pipelines and compressor stations that pressurise natural gas for transport along pipelines. Estimates of fugitive emissions from transmission, storage and distribution have been criticized for reliance on old data from inappropriate sources (1970s Russian gas pipelines). In this study, we investigate fugitive emissions of CH4 from the UK high pressure national transmission system. The study took two approaches. Firstly, CH4 concentration is detected by driving along roads bisecting high pressure gas pipelines and also along an equivalent distance along a route where no high pressure gas pipeline was nearby. Five pipelines and five equivalent control routes were driven and the test was that CH4 measurements, when adjusted for distance and wind speed, should be greater on any route with a pipe than any route without a pipe. Secondly, 5 km of a high pressure gas pipeline and 5 km of equivalent farmland, were walked and soil gas (above the pipeline where present) was analysed every 7 m using a tunable diode laser. When wind adjusted 92 km of high pressure pipeline and 72 km of control route were drive over a 10 day period. When wind and distance adjusted CH4 fluxes were significantly greater on routes with a pipeline than those without. The smallest leak detectable was 3% above ambient (1.03 relative concentration) with any leaks below 3% above ambient assumed ambient. The number of leaks detected along the pipelines correlate to the estimated length of pipe joints, inferring that there are constant fugitive CH4 emissions from these joints. When scaled up to the UK's National Transmission System pipeline length of 7600 km gives a fugitive CH4 flux of 62.6 kt CH4/yr with a CO2 equivalent of 1570 kt CO2eq/yr - this fugitive emission from high pressure pipelines is 0.14% of the annual gas supply.

Flux estimation of fugitive particulate matter emissions from loose Calcisols at construction sites

NASA Astrophysics Data System (ADS)

Hassan, Hala A.; Kumar, Prashant; Kakosimos, Konstantinos E.

2016-09-01

A major source of airborne pollution in arid and semi-arid environments (i.e. North Africa, Middle East, Central Asia, and Australia) is the fugitive particulate matter (fPM), which is a frequent product of wind erosion. However, accurate determination of fPM is an ongoing scientific challenge. The objective of this study is to examine fPM emissions from the loose Calcisols (i.e. soils with a substantial accumulation of secondary carbonates), owing to construction activities that can be frequently seen nowadays in arid urbanizing regions such as the Middle East. A two months field campaign was conducted at a construction site, at rest, within the city of Doha (Qatar) to measure number concentrations of PM over a size range of 0.25-32 μm using light scattering based monitoring stations. The fPM emission fluxes were calculated using the Fugitive Dust Model (FDM) in an iterative manner and were fitted to a power function, which expresses the wind velocity dependence. The power factors were estimated as 1.87, 1.65, 2.70 and 2.06 for the four different size classes of particles ≤2.5, 2.5-6, 6-10 and ≤10 μm, respectively. Fitted power function was considered acceptable given that adjusted R2 values varied from 0.13 for the smaller particles and up to 0.69 for the larger ones. These power factors are in the same range of those reported in the literature for similar sources. The outcome of this study is expected to contribute to the improvement of PM emission inventories by focusing on an overlooked but significant pollution source, especially in dry and arid regions, and often located very close to residential areas and sensitive population groups. Further campaigns are recommended to reduce the uncertainty and include more fPM sources (e.g. earthworks) and other types of soil.

Size-resolved dust and aerosol contaminants associated with copper and lead smelting emissions: implications for emission management and human health.

PubMed

Csavina, Janae; Taylor, Mark P; Félix, Omar; Rine, Kyle P; Eduardo Sáez, A; Betterton, Eric A

2014-09-15

Mining operations, including crushing, grinding, smelting, refining, and tailings management, are a significant source of airborne metal and metalloid contaminants such as As, Pb and other potentially toxic elements. In this work, we show that size-resolved concentrations of As and Pb generally follow a bimodal distribution with the majority of contaminants in the fine size fraction (<1 μm) around mining activities that include smelting operations at various sites in Australia and Arizona. This evidence suggests that contaminated fine particles (<1 μm) are the result of vapor condensation and coagulation from smelting operations while coarse particles are most likely the result of windblown dust from contaminated mine tailings and fugitive emissions from crushing and grinding activities. These results on the size distribution of contaminants around mining operations are reported to demonstrate the ubiquitous nature of this phenomenon so that more effective emission management and practices that minimize health risks associated with metal extraction and processing can be developed. Copyright © 2014 Elsevier B.V. All rights reserved.

Superfund record of decision amendment (EPA Region 5): Carter Industrials Site, Detroit, MI, February 28, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This decision document changes a decision made on September 18, 1991 in which the United States Environmental Protection Agency (U.S. EPA) chose low-temperature thermal desorption as the remedy for PCB contamination at the Carter Industrials Site in Detroit, Michigan. U.S. EPA is hereby amending the 1991 Record of Decision (PB92-964126) to select off-site disposal as the remedy. This response action addresses remediation of PCB-contaminated soil, debris, and buildings at the Carter Industrials Site. The principal threats posed by conditions at the Site include inhalation of volatilized PCBs and fugitive dust, and dermal contact with contaminated materials. The amended remedy willmore » eliminate these threats.« less

40 CFR 57.503 - Control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Control measures. 57.503 Section 57.503... NONFERROUS SMELTER ORDERS Fugitive Emission Evaluation and Control § 57.503 Control measures. The NSO of any... requirement of § 57.501. Measures required to be implemented may include: (a) Additional supplementary control...

40 CFR 57.503 - Control measures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Control measures. 57.503 Section 57.503... NONFERROUS SMELTER ORDERS Fugitive Emission Evaluation and Control § 57.503 Control measures. The NSO of any... requirement of § 57.501. Measures required to be implemented may include: (a) Additional supplementary control...

40 CFR 57.503 - Control measures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Control measures. 57.503 Section 57.503... NONFERROUS SMELTER ORDERS Fugitive Emission Evaluation and Control § 57.503 Control measures. The NSO of any... requirement of § 57.501. Measures required to be implemented may include: (a) Additional supplementary control...

40 CFR 57.503 - Control measures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Control measures. 57.503 Section 57.503... NONFERROUS SMELTER ORDERS Fugitive Emission Evaluation and Control § 57.503 Control measures. The NSO of any... requirement of § 57.501. Measures required to be implemented may include: (a) Additional supplementary control...

Simplified and low cost optical remote sensing technology for fenceline monitoring of fugitive releases

EPA Science Inventory

Reducing fugitive emissions of hazardous air pollutants from industrial facilities is an ongoing priority for the U.S. Environmental Protection Agency (EPA). Unlike stack emissions, fugitive releases are difficult to detect due to their spatial extent and inherent temporal variab...

75 FR 6823 - Prevention of Significant Deterioration (PSD) and Nonattainment New Source Review (NSR...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-11

...-AP73 Prevention of Significant Deterioration (PSD) and Nonattainment New Source Review (NSR... Review (NSR): Reconsideration of Fugitive Emissions'' (``Fugitive Emissions Rule''). The Fugitive... whether a physical or operation change results in a major modification only for sources in industries that...

Health hazard prospecting by modeling wind transfer of metal-bearing dust from mining waste dumps: application to Jebel Ressas Pb-Zn-Cd abandoned mining site (Tunisia).

PubMed

Ghorbel, Manel; Munoz, Marguerite; Solmon, Fabien

2014-10-01

This work presents a modeling approach to simulate spatial distribution of metal contamination in aerosols with evaluation of health hazard. This approach offers the advantage to be non-intrusive, less expensive than sampling and laboratory analyses. It was applied to assess the impact of metal-bearing dust from mining wastes on air quality for a nearby community and agricultural lands in Jebel Ressas (Tunisia) locality. Dust emission rates were calculated using existing parameterization adapted to the contamination source composed of mining wastes. Metal concentrations were predicted using a Gaussian model (fugitive dust model) with, as input: emission rates, dump physical parameters and meteorological data measured in situ for 30 days in summertime. Metal concentration maps were built from calculated PM10 particle concentrations. They evidence the areas where Pb and Cd concentrations exceeded WHO guidelines (0.5 and 0.005 µg/m(3), respectively). Maximum concentrations of Pb and Cd in PM10 are, respectively, of 5.74 and 0.0768 µg/m(3) for measured wind speed values up to 22 m/s. Preferential areas of contamination were determined in agricultural lands to the NW from the source dump where Pb and Cd exceeded guidelines up to a distance of 1,200 m. The secondary spreading directions were SW and E, toward the village. Health hazard prospecting shown that a major part of the village was exposed to contaminated dust and that daily hazard quotient (HQ) values reached locally 118 and 158, respectively, for Pb and Cd during the study period. However, HQ variations in the village are high, both temporally and geographically.

Characteristics of polycyclic aromatic hydrocarbons and their gas/particle partitioning from fugitive emissions in coke plants

NASA Astrophysics Data System (ADS)

Mu, Ling; Peng, Lin; Liu, Xiaofeng; Song, Chongfang; Bai, Huiling; Zhang, Jianqiang; Hu, Dongmei; He, Qiusheng; Li, Fan

2014-02-01

Coking is one of the most important emission sources of polycyclic aromatic hydrocarbons (PAHs) in China. However, there is little information available on the emission characteristics of PAHs from fugitive emission during coking, especially on the specific processes dominating the gas-particle partitioning of PAHs. In this study, emission characteristics and gas-particle partitioning of PAHs from fugitive emission in four typical coke plants (CPs) with different scales and techniques were investigated. The average concentrations of total PAHs from fugitive emission at CP2, CP3 and CP4 (stamp charging) were 146.98, 31.82, and 35.20 μg m-3, which were 13.38-, 2.90- and 3.20-fold higher, respectively, than those at CP1 (top charging, 10.98 μg m-3). Low molecular weight PAHs with 2-3 rings made up 75.3% of the total PAHs on average, and the contributions of particulate PAH to the total BaP equivalent concentrations (BaPeq) in each plant were significantly higher than the corresponding contributions to the total PAH mass concentrations. The calculated total BaPeq concentrations varied from 0.19 to 10.86 μg m-3 with an average of 3.14 μg m-3, and more efficient measures to control fugitive emission in coke plants should be employed to prevent or reduce the health risk to workers. Absorption into organic matter dominated the gas-particle partitioning for most of the PAHs including PhA, FluA, Chr, BbF, BkF and BaP, while adsorption on elemental carbon appeared to play a dominant role for AcPy, AcP and Flu.

PARTICULATE EMISSION MEASUREMENTS FROM CONTROLLED CONSTRUCTION ACTIVITIES

EPA Science Inventory

The report summarized the results of field testing of the effectiveness of control measures for sources of fugitive particulate emissions found at construction sites. The effectiveness of watering temporary, unpaved travel surfaces on emissions of particulate matter with aerodyna...

77 FR 22676 - Revisions to the Arizona State Implementation Plan, Pinal County Air Quality Control District

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... the Arizona State Implementation Plan, Pinal County Air Quality Control District AGENCY: Environmental... disapproval of a revision to the Pinal County Air Quality Control District portion of the Arizona State... the Control Officer to determine whether the manner of control of fugitive emissions is satisfactory...

Chemical composition and source apportionment of PM10 at an urban background site in a high-altitude Latin American megacity (Bogota, Colombia).

PubMed

Ramírez, Omar; Sánchez de la Campa, A M; Amato, Fulvio; Catacolí, Ruth A; Rojas, Néstor Y; de la Rosa, Jesús

2018-02-01

Bogota registers frequent episodes of poor air quality from high PM 10 concentrations. It is one of the main Latin American megacities, located at 2600 m in the tropical Andes, but there is insufficient data on PM 10 source contribution. A characterization of the chemical composition and the source apportionment of PM 10 at an urban background site in Bogota was carried out in this study. Daily samples were collected from June 2015 to May 2016 (a total of 311 samples). Organic carbon (OC), elemental carbon (EC), water soluble compounds (SO 4 2- , Cl - , NO 3 - , NH 4 + ), major elements (Al, Fe, Mg, Ca, Na, K, P) and trace metals (V, Cd, Pb, Sr, Ba, among others) were analyzed. The results were interpreted in terms of their variability during the rainy season (RS) and the dry season (DS). The data obtained revealed that the carbonaceous fraction (∼51%) and mineral dust (23%) were the main PM 10 components, followed by others (15%), Secondary Inorganic Compounds (SIC) (11%) and sea salt (0.4%). The average concentrations of soil, SIC and OC were higher during RS than DS. However, peak values were observed during the DS due to photochemical activity and forest fires. Although trace metals represented <1% of PM 10 , high concentrations of toxic elements such as Pb and Sb on RS, and Cu on DS, were obtained. By using a PMF model, six factors were identified (∼96% PM 10 ) including fugitive dust, road dust, metal processing, secondary PM, vehicles exhaust and industrial emissions. Traffic (exhaust emissions + road dust) was the major PM 10 source, accounting for ∼50% of the PM 10 . The results provided novel data about PM 10 chemical composition, its sources and its seasonal variability during the year, which can help the local government to define control strategies for the main emission sources during the most critical periods. Copyright © 2017 Elsevier Ltd. All rights reserved.

Concentrations and bioaccessibility of metals in vegetation and dust near a mining haul road, Cape Krusenstern National Monument, Alaska

USGS Publications Warehouse

Brumbaugh, W.G.; Morman, S.A.; May, T.W.

2011-01-01

Vegetation, sub-surface peat, and road dust were sampled near the Delong Mountain Transportation System (DMTS) haul road in northwest Alaska in 2005-2006 to document aluminum, barium, cadmium, lead, and zinc concentrations, and to evaluate bioaccessibility of these metals. The DMTS haul road is the transport corridor between Red Dog Mine (a large-scale, lead-zinc mine and mill) and the coastal shipping port, and it traverses National Park Service lands. Compared to reference locations, total metal concentrations in four types of vegetation (birch, cranberry, and willow leaves, and cotton grass blades/stalks) collected 25 m from the haul road were enriched on average by factors of 3.5 for zinc, 8.0 for barium, 20 for cadmium, and 150 for lead. Triple rinsing of vegetation with a water/methanol mixture reduced metals concentrations by at most 50%, and cadmium and zinc concentrations were least affected by rinsing. Cadmium and zinc bioaccessibility was greater in vegetation (50% to 100%) than in dust (15% to 20%); whereas the opposite pattern was observed for lead bioaccessibility (<30% in vegetation; 50% in dust). Barium exhibited low-to-intermediate bioaccessibility in dust and vegetation (20% to 40%), whereas aluminum bioaccessibility was relatively low (<6%) in all sample types. Our reconnaissance-level study indicates that clean-up and improvements in lead/zinc concentrate transfer activities have been effective; however, as of 2006, metal dispersion from past and/or present releases of fugitive dusts along the DMTS road still may have been contributing to elevated metals in surface vegetation. Vegetation was most enriched in lead, but because bioaccessibility of cadmium was greater, any potential risks to animals that forage near the haul road might be equally important for both of these metals. ?? 2011 Springer Science+Business Media B.V. (outside the USA).

PM 10 and ozone control strategy to improve visibility in the los angeles basin

NASA Astrophysics Data System (ADS)

Farber, Robert J.; Welsing, Peter R.; Rozzi, Carlo

The greater Los Angeles metropolitan area is in violation of the United States Environmental Protection Agency (USEPA) ambient standards for both ozone and PM 10. Accompanying these violations are hazy summer conditions, with current annual median visibility in the inland portions of Los Angeles running about 13 km, and visibilities decreasing to about 3 km on the 90th percentile days (worst days). The USEPA has given the local air pollution control agency until 2010 to bring the area into compliance with these standards. Because of continued population growth, accompanying light industry, dependence on private motor vehicles, and adverse natural meteorological conditions, emission reductions costing billions of dollars will be needed between now and 2010. The combination of emission reductions which will result in the fastest ozone and PM 10 cleanup at the lowest cost are presented. Substantial emission reductions in NO x, reactive hydrocarbons, SO x, ammonia, soot and fugitive dust will result in visibility improvements in the Los Angeles area. However, enactment of this comprehensive control strategy will only improve the annual median visibility to about 20 km and the 90th percentile days to 6.5 km. Significant changes in fine mass will result in relatively small changes in perceived visibility since the human eye is unable to differentiate visual range changes even as large as 40% in an urban landscape typical of Los Angeles.

Ozone and its potential control strategy for Chon Buri city, Thailand.

PubMed

Prabamroong, Thayukorn; Manomaiphiboon, Kasemsan; Limpaseni, Wongpun; Sukhapan, Jariya; Bonnet, Sebastien

2012-12-01

This work studies O3 pollution for Chon Buri city in the eastern region of Thailand, where O3 has become an increased and serious concern in the last decade. It includes emission estimation and photochemical box modeling in support of investigating the underlying nature of O3 formation over the city and the roles of precursors emitted from sources. The year 2006 was considered and two single-day episodes (January 29 and February 14) were chosen for simulations. It was found that, in the city, the industrial sector is the largest emissions contributor for every O3 precursor (i.e., NO(x), non-methane volatile organic compounds or NMVOC, and CO), followed by on-road mobile group. Fugitive NMVOC is relatively large, emitted mainly from oil refineries and tank farms. Simulated results acceptably agree with observations for daily maximum O3 level in both episodes and evidently indicate the VOC-sensitive regime for O3 formation. This regime is also substantiated by morning NMVOC/NO(x) ratios observed in the city. The corresponding O3 isopleth diagrams suggest NMVOC control alone to lower elevated O3. In seeking a potential O3 control strategy for the city, a combination of brute-force sensitivity tests, an experimental design, statistical modeling, and cost optimization was employed. A number of emission subgroups were found to significantly contribute to O3 formation, based on the February 14 episode, for example, oil refinery (fugitive), tank farm (fugitive), passenger car (gasoline), and motorcycle (gasoline). But the cost-effective strategy suggests control only on the first two subgroups to meet the standard. The cost of implementing the strategy was estimated and found to be small (only 0.2%) compared to the gross provincial product generated by the entire province where the city is located within. These findings could be useful as a needed guideline to support O3 management for the city. Elevated O3 in the urban and industrial city of Chon Buri needs better understanding of the problem and technical guidelines for its management. With a city-specific emission inventory and air quality modeling, O3 formation was found to be VOC sensitive, and a cost-effective control strategy developed highlights fugitive emissions from the industrial sector to be controlled.

40 CFR Table 3 to Subpart Ooo of... - Fugitive Emission Limits

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Fugitive Emission Limits 3 Table 3 to... Mineral Processing Plants Pt. 60, Subpt. OOO, Table 3 Table 3 to Subpart OOO of Part 60—Fugitive Emission...; andPeriodic inspections of water sprays according to § 60.674(b) and § 60.676(b); and A repeat...

40 CFR Table 3 to Subpart Ooo of... - Fugitive Emission Limits

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Fugitive Emission Limits 3 Table 3 to... Mineral Processing Plants Subpt. OOO, Table 3 Table 3 to Subpart OOO of Part 60—Fugitive Emission Limits... performance test according to § 60.11 of this part and § 60.675 of this subpart; andPeriodic inspections of...

40 CFR Table 3 to Subpart Ooo of... - Fugitive Emission Limits

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Fugitive Emission Limits 3 Table 3 to... Mineral Processing Plants Pt. 60, Subpt. OOO, Table 3 Table 3 to Subpart OOO of Part 60—Fugitive Emission...; andPeriodic inspections of water sprays according to § 60.674(b) and § 60.676(b); and A repeat...

40 CFR Table 3 to Subpart Ooo - Fugitive Emission Limits

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Fugitive Emission Limits 3 Table 3 to... Processing Plants Subpt. OOO, Table 3 Table 3 to Subpart OOO—Fugitive Emission Limits Table 3 to Subpart OOO...; andPeriodic inspections of water sprays according to § 60.674(b) and § 60.676(b); and A repeat...

40 CFR Table 3 to Subpart Ooo - Fugitive Emission Limits

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Fugitive Emission Limits 3 Table 3 to... Processing Plants Subpt. OOO, Table 3 Table 3 to Subpart OOO—Fugitive Emission Limits Table 3 to Subpart OOO...; andPeriodic inspections of water sprays according to § 60.674(b) and § 60.676(b); and A repeat...

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2010 CFR

2010-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2010 CFR

2010-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a...

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2012 CFR

2012-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a...

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2012 CFR

2012-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2013 CFR

2013-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a...

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2011 CFR

2011-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2013 CFR

2013-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2011 CFR

2011-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a...

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2014 CFR

2014-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Code of Federal Regulations, 2014 CFR

2014-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a...

Directional passive ambient air monitoring of ammonia for fugitive source attribution; a field trial with wind tunnel characteristics

NASA Astrophysics Data System (ADS)

Solera García, M. A.; Timmis, R. J.; Van Dijk, N.; Whyatt, J. D.; Leith, I. D.; Leeson, S. R.; Braban, C. F.; Sheppard, L. J.; Sutton, M. A.; Tang, Y. S.

2017-10-01

Atmospheric ammonia is a precursor for secondary particulate matter formation, which harms human health and contributes to acidification and eutrophication. Under the 2012 Gothenburg Protocol, 2005 emissions must be cut by 6% by 2020. In the UK, 83% of total emissions originate from agricultural practices such as fertilizer use and rearing of livestock, with emissions that are spatially extensive and variable in nature. Such fugitive emissions make resolving and tracking of individual site performance challenging. The Directional Passive Air quality Sampler (DPAS) was trialled at Whim Bog, an experimental site with a wind-controlled artificial release of ammonia, in combination with CEH-developed ammonia samplers. Whilst saturation issues were identified, two DPAS-MANDE (Mini Annular Denuder) systems, when deployed in parallel, displayed an average relative deviation of 15% (2-54%) across all 12 directions, with the directions exposed to the ammonia source showing ∼5% difference. The DPAS-MANDE has shown great potential for directional discrimination and can contribute to the understanding and management of fugitive ammonia sources from intensive agriculture sites.

CELiS (Compact Eyesafe Lidar System), a portable 1.5 μm elastic lidar system for rapid aerosol concentration measurement: Part 1, Instrument Design and Operation

NASA Astrophysics Data System (ADS)

Bird, A. W.; Wojcik, M.; Moore, K. D.; Lemon, R.

2014-12-01

CELiS (Compact Eyesafe Lidar System) is an elastic lidar system conceived for the purpose of monitoring air quality environmental compliance regarding particulate matter (PM) generated from off-road use of wheeled and tracked vehicles. CELiS is a prototype instrument development by the Space Dynamics Laboratory to demonstrate a small, low power, eye-safe lidar system capable of monitoring PM fence-line concentration of fugitive dust from off-road vehicle activity as part of the SERDP (Strategic Environmental Research and Development Program) Measurement and Modeling of Fugitive Dust Emission from Off-Road Department of Defense Activities program. CELiS is small, lightweight and easily transportable for quick setup and measurement of PM concentration and emissions. The instrument is mounted on Moog Quickset pan and tilt positioner. Ground support equipment includes portable racks with laser power and cooler, power supplies, readout electronics and computer. The complete CELiS instrument weighs less than 300 lbs., is less than 1 cubic meters in volume and uses 700 W of 120V AC power. CELiS has a working range of better than 6km and a range resolution of 1.5m-6m. CELiS operates in a biaxial configuration at the 1.5μm eyesafe wavelength. The receiver is an off-axis parabolic (OAP) telescope, aft-optics and alignment assembly and InGaAs APD detector readout. The transmitter is a 20Hz PRF - 25mJ Quantel 1.574 μm laser with a 20x beam expander. Both the receiver and transmitter are mounted on a carbon fiber optical breadboard with a custom mounting solution to minimize misalignment due to thermal operating range (0-40 C) and pointing vectors. Any lidar system used to monitor fence-line PM emissions related to off-road training activities will be subject to a strict eye-safety requirement to protect both troops and wildlife. CELiS is eyesafe at the output aperture. CELiS has participated in two Dugway Proving Ground Lidar exercises performing within expectations. Retrieval of particulate matter concentration is presented in companion poster by K. Moore.

Contamination characteristics and possible sources of PM10 and PM2.5 in different functional areas of Shanghai, China

NASA Astrophysics Data System (ADS)

Wang, Jun; Hu, Zimei; Chen, Yuanyuan; Chen, Zhenlou; Xu, Shiyuan

2013-04-01

From July 2009 through September 2010, PM10 and PM2.5 were collected at two different functional areas in Shanghai (Baoshan district, an industrial area, and Putuo district, a mixed-use area of residential, commercial, and educational compounds). In our analysis, 15 elements were determined using a 710-ES Inductively Coupled Plasma-Emission Spectrometer (ICP-AES). The contents of PM2.5, PM10, and metal elements at the two different sites were comparatively analyzed. The results show that the mean annual concentrations of PM10 and PM2.5 (149.22 μg m-3 and 103.07 μg m-3, respectively) in Baoshan district were significantly higher than those in Putuo district (97.44 μg m-3 and 62.25 μg m-3 respectively). The concentrations of PM10 and PM2.5 were both greatest in winter and lowest in summer, with the two different sites exhibiting the same seasonal variation. It was found that the proportions of 15 metal elements in PM10 and PM2.5 in Baoshan district were 20.49% and 20.56%, respectively, while the proportions in Putuo district were higher (25.98% and 25.93%, respectively). In addition, the proportions of eight heavy metals in PM10 and PM2.5 were 5.50% and 3.07%, respectively, for Baoshan district, while these proportions in Putuo district were 3.18% and 2.77%, respectively, indicating that heavy metal pollution is more pronounced in Baoshan district. Compared with cities in developed countries, the total levels of PM10, PM2.5 and heavy metals in Shanghai were slightly higher. Scanning electron microscopy (SEM) and principal component analysis (PCA) suggested that the possible sources of PM10 in Baoshan district were ground level fugitive dust, traffic sources, and industrial activities, whereas PM2.5 mainly originated from industrial activities, coal combustion, and traffic sources. The sources are same for PM10 and PM2.5 in Putuo region, which originate from traffic sources and ground level fugitive dust.

Novorossiysk agglomeration landscapes and cement production: geochemical impact assessment

NASA Astrophysics Data System (ADS)

Alekseenko, A. V.; Pashkevich, M. A.

2016-09-01

The article deals with assessing the environmental impact of marl mining and cement production in Novorossiysk city (Krasnodar krai, Russia). The existing methods of studying the environmental effects caused by the cement industry have been reviewed. Soil and aquatic vegetation sampling has been carried out and the gross concentration of metals in the samples has been defined. The research has been conducted in the certified and accredited laboratory using emission spectral analysis. The external control has been carried out via X-ray fluorescence analysis. Based on the collected data, main chemical pollutants in soil cover and water area near the cement plant have been identified. The contaminants released by urban enterprises and motor vehicle emissions, as well as fugitive dust from dumps and the cement factory, lead to multi-element lithogeochemical anomaly at geochemical barriers in soils. Accumulation of pollutants in soil depends on the type of land use and the area relief. The most contaminated aquatic landscapes have been identified in the inner bay. According to this information, the technical proposals can be prepared for environmental safety management in strongly polluted city areas, as well as for the reclamation design in the areas currently experiencing the negative impact of cement production.

40 CFR 63.11526 - What are the standards for new and existing ferroalloys production facilities?

Code of Federal Regulations, 2011 CFR

2011-07-01

... must not discharge to the atmosphere visible emissions (VE) from the control device that exceed 5... atmosphere fugitive PM emissions from the furnace building containing the electrometallurgical operations...

40 CFR 63.11526 - What are the standards for new and existing ferroalloys production facilities?

Code of Federal Regulations, 2013 CFR

2013-07-01

... must not discharge to the atmosphere visible emissions (VE) from the control device that exceed 5... atmosphere fugitive PM emissions from the furnace building containing the electrometallurgical operations...

40 CFR 63.11526 - What are the standards for new and existing ferroalloys production facilities?

Code of Federal Regulations, 2014 CFR

2014-07-01

... must not discharge to the atmosphere visible emissions (VE) from the control device that exceed 5... atmosphere fugitive PM emissions from the furnace building containing the electrometallurgical operations...

40 CFR 63.11526 - What are the standards for new and existing ferroalloys production facilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... must not discharge to the atmosphere visible emissions (VE) from the control device that exceed 5... atmosphere fugitive PM emissions from the furnace building containing the electrometallurgical operations...

40 CFR 63.11526 - What are the standards for new and existing ferroalloys production facilities?

Code of Federal Regulations, 2012 CFR

2012-07-01

... must not discharge to the atmosphere visible emissions (VE) from the control device that exceed 5... atmosphere fugitive PM emissions from the furnace building containing the electrometallurgical operations...

PM RESEARCH

EPA Science Inventory

Activity Area (F03): PM Implementation NRMRL conducts research to improve the techniques used to quantify PM and PM precursor emissions from stationary, mobile, and fugitive sources and investigates the performance and cost of innovative control technology systems. The emission...

Vadose Zone and Surficial Monitoring a Controlled Release of Methane in the Borden Aquifer, Ontario.

NASA Astrophysics Data System (ADS)

Forde, O.; Mayer, K. U.; Cahill, A.; Parker, B. L.; Cherry, J. A.

2015-12-01

Development of shale gas resources and potential impacts on groundwater and fugitive gas emissions necessitates further research on subsurface methane gas (CH4) migration and fate. To address this issue, a controlled release experiment is undertaken at the Borden research aquifer, Ontario, Canada. Due to low solubility, it is expected that the injection will lead to gas exsolution and ebullition. Gas migration is expected to extend to the unsaturated zone and towards the ground surface, and may possibly be affected by CH4 oxidation. The project consists of multiple components targeting the saturated zone, unsaturated zone, and gas emissions at the ground surface. This presentation will focus on the analysis of surficial CO2 and CH4 effluxes and vadose zone gas composition to track the temporal and spatial evolution of fugitive gas. Surface effluxes are measured with flux chambers connected to a laser-based gas analyzer, and subsurface gas samples are being collected via monitoring wells equipped with sensors for oxygen, volumetric water content, electrical conductivity, and temperature to correlate with changes in gas composition. First results indicate rapid migration of CH4 to the ground surface in the vicinity of the injection locations. We will present preliminary data from this experiment and evaluate the distribution and rate of gas migration. This research specifically assesses environmental risks associated with fugitive gas emissions related to shale gas resource development.

Elucidating the urban levels, sources and health risks of polycyclic aromatic hydrocarbons (PAHs) in Pakistan: Implications for changing energy demand.

PubMed

Hamid, Naima; Syed, Jabir Hussain; Junaid, Muhammad; Mahmood, Adeel; Li, Jun; Zhang, Gan; Malik, Riffat Naseem

2018-04-01

Due to the severe fuel crisis in terms of natural gas, a paradigm shift in fuel combustion (diesel, gasoline, and biomass) may increase the atmospheric emissions and associated health risks in Pakistan. Present study was aimed to investigate the concentration of fugitive PAHs in the environment (outdoor and indoor settings), associated probabilistic health risk assessment in the exposed population, and possible linkage between fuel consumption patterns and PAHs emissions in twin cities (Rawalpindi and Islamabad) of Pakistan. Results showed that the mean PAHs concentrations (air: 2390pgm -3 ; dust: 167ngg -1 ) in the indoor environment were higher than that of the outdoor environment (air: 2132pgm -3 ; dust: 90.0ngg -1 ). Further, the source apportionment PCA-MLR receptor model identified diesel and gasoline combustion as the primary PAHs sources in the urban and sub-urban settings. Estimated life cancer risk (LCR) potential via inhalation to indoor PAHs was higher with a probability of 2.0 cases per 10,000 inhabitants as compared to outdoor exposure. Incremental lifetime cancer risk (ILCR) model from exposure to dust bound PAHs showed risk in the order of ingestion>dermal>inhalation for various exposure pathways. Likewise, estimated daily intake (EDI) model reflects that PAHs in surface dust enter into the human body mainly through the respiratory system because EDI for breathing was reported higher than that of oral intake. Therefore, adoption of sustainable fuels is recommended to meet the energy requirements and to reduce PAHs emissions and related health risks in the twin cities of Pakistan. Copyright © 2017 Elsevier B.V. All rights reserved.

Global emissions of PM10 and PM2.5 from agricultural tillage and harvesting operations

NASA Astrophysics Data System (ADS)

Chen, W.; Tong, D.; Lee, P.

2014-12-01

Soil particles emitted during agricultural activities is a major recurring source contributing to atmospheric aerosol loading. Emission inventories of agricultural dust emissions have been compiled in several regions. These inventories, compiled based on historic survey and activity data, may reflect the current emission strengths that introduce large uncertainties when they are used to drive chemical transport models. In addition, there is no global emission inventory of agricultural dust emissions required to support global air quality and climate modeling. In this study, we present our recent efforts to develop a global emission inventory of PM10 and PM2.5 released from field tillage and harvesting operations using an emission factors-based approach. Both major crops (e.g., wheat and corn) and forage production were considered. For each crop or forage, information of crop area, crop calendar, farming activities and emission factors of specified operations were assembled. The key issue of inventory compilation is the choice of suitable emission factors for specified operations over different parts of the world. Through careful review of published emission factors, we modified the traditional emission factor-based model by multiplying correction coefficient factors to reflect the relationship between emission factors, soil texture, and climate conditions. Then, the temporal (i.e., monthly) and spatial (i.e., 0.5º resolution) distribution of agricultural PM10 and PM2.5 emissions from each and all operations were estimated for each crop or forage. Finally, the emissions from individual crops were aggregated to assemble a global inventory from agricultural operations. The inventory was verified by comparing the new data with the existing agricultural fugitive dust inventory in North America and Europe, as well as satellite observations of anthropogenic agricultural dust emissions.

77 FR 13150 - Notice of Lodging of Third Amendment to Consent Decree Under the Clean Air Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

... adopt facility-wide enhanced benzene waste monitoring and fugitive emission control programs..., $98,500, and $21,000 to resolve alleged Benzene Waste Operations NESHAP (``BWON'') violations at its...

A Mobile Sensing Approach for Regional Surveillance of Fugitive Methane Emissions in Oil and Gas Production.

PubMed

Albertson, John D; Harvey, Tierney; Foderaro, Greg; Zhu, Pingping; Zhou, Xiaochi; Ferrari, Silvia; Amin, M Shahrooz; Modrak, Mark; Brantley, Halley; Thoma, Eben D

2016-03-01

This paper addresses the need for surveillance of fugitive methane emissions over broad geographical regions. Most existing techniques suffer from being either extensive (but qualitative) or quantitative (but intensive with poor scalability). A total of two novel advancements are made here. First, a recursive Bayesian method is presented for probabilistically characterizing fugitive point-sources from mobile sensor data. This approach is made possible by a new cross-plume integrated dispersion formulation that overcomes much of the need for time-averaging concentration data. The method is tested here against a limited data set of controlled methane release and shown to perform well. We then present an information-theoretic approach to plan the paths of the sensor-equipped vehicle, where the path is chosen so as to maximize expected reduction in integrated target source rate uncertainty in the region, subject to given starting and ending positions and prevailing meteorological conditions. The information-driven sensor path planning algorithm is tested and shown to provide robust results across a wide range of conditions. An overall system concept is presented for optionally piggybacking of these techniques onto normal industry maintenance operations using sensor-equipped work trucks.

Refinery evaluation of optical imaging to locate fugitive emissions.

PubMed

Robinson, Donald R; Luke-Boone, Ronke; Aggarwal, Vineet; Harris, Buzz; Anderson, Eric; Ranum, David; Kulp, Thomas J; Armstrong, Karla; Sommers, Ricky; McRae, Thomas G; Ritter, Karin; Siegell, Jeffrey H; Van Pelt, Doug; Smylie, Mike

2007-07-01

Fugitive emissions account for approximately 50% of total hydrocarbon emissions from process plants. Federal and state regulations aiming at controlling these emissions require refineries and petrochemical plants in the United States to implement a Leak Detection and Repair Program (LDAR). The current regulatory work practice, U.S. Environment Protection Agency Method 21, requires designated components to be monitored individually at regular intervals. The annual costs of these LDAR programs in a typical refinery can exceed US$1,000,000. Previous studies have shown that a majority of controllable fugitive emissions come from a very small fraction of components. The Smart LDAR program aims to find cost-effective methods to monitor and reduce emissions from these large leakers. Optical gas imaging has been identified as one such technology that can help achieve this objective. This paper discusses a refinery evaluation of an instrument based on backscatter absorption gas imaging technology. This portable camera allows an operator to scan components more quickly and image gas leaks in real time. During the evaluation, the instrument was able to identify leaking components that were the source of 97% of the total mass emissions from leaks detected. More than 27,000 components were monitored. This was achieved in far less time than it would have taken using Method 21. In addition, the instrument was able to find leaks from components that are not required to be monitored by the current LDAR regulations. The technology principles and the parameters that affect instrument performance are also discussed in the paper.

Development of a life-cycle fugitive methane emissions model utilizing device level emissions and activity factors

NASA Astrophysics Data System (ADS)

Englander, J.; Brandt, A. R.

2017-12-01

There has been numerous studies in quantifying the scale of fugitive emissions from across the natural gas value chain. These studies have typically focused on either specific types of equipment (such as valves) or on a single part of the life-cycle of natural gas production (such as gathering stations).1,2 However it has been demonstrated that average emissions factors are not sufficient for representing leaks in the natural gas system.3 In this work, we develop a robust estimate of fugitive emissions rates by incorporating all publicly available studies done at the component up to the process level. From these known studies, we create a database of leaks with normalized nomenclature from which leak estimates can be drawn from actual leak observations. From this database, and parameterized by meta-data such as location, scale of study, or placement in the life-cycle, we construct stochastic emissions factors specific for each process unit. This will be an integrated tool as part of the Oil production greenhouse gas estimator (OPGEE) as well as the Fugitive Emissions Abatement Simulation Toolkit (FEAST) models to enhances their treatment of venting and fugitive emissions, and will be flexible to include user provided data and input parameters.4,51. Thoma, ED et al. Assessment of Uinta Basin Oil and Natural Gas Well Pad Pneumatic Controller Emissions. J. Environ. Prot. 2017. 2. Marchese, AJ et al. Methane Emissions from United States Natural Gas Gathering and Processing. ES&T 2015. doi:10.1021/acs.est.5b02275 3. Brandt, AR et al. Methane Leaks from Natural Gas Systems Follow Extreme Distributions. ES&T 2016. doi:10.1021/acs.est.6b04303 4. El-Houjeiri, HM et al. An open-source LCA tool estimating greenhouse gas emissions from crude oil production using field characteristics. ES&T 2013. doi: 10.1021/es304570m 5. Kemp, CE et al. Comparing Natural Gas Leakage Detection Technologies Using an Open-Source `Virtual Gas Field' Simulator. ES&T 2016. doi:10.1021/acs.est.5b06068

40 CFR 52.515 - Original identification of plan section.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Natural Resources and Environmental Control. (19) The Plan revision entitled “Revisions to the..., Cylinder wipe, Emission unit, Federally enforceable, Flexography, Fugitive emission, Gas services, Gas..., Freeboard ratio, Mayor, Vehicular fuel tank. Abbreviations: (Degree), VOC, “%”. (ii) Additional material. (A...

Health assessment for Shaw Avenue Dump, Charles City, Iowa, Region 7. CERCLIS No. IAD980630560. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-12-07

The Shaw Avenue Dump Site is listed on the National Priorities List. The 8-acre city dump site, consisting of three waste-disposal areas, is located in southeast Charles City approximately 500 feet east of the Cedar River. Sludge from the Charles City waste water treatment plant, which received liquid waste discharge from Salisbury, was placed from 1949 to 1969 in the northern waste cells and in the undefined area on the southern portion of the site. Arsenic is the contaminant of concern at the Shaw Avenue Dump Site. The site is considered to be of public health concern because of themore » potential risk to human health caused by possible exposure to hazardous substances via ingestion of ground water, soil, and surface water; inhalation of fugitive dust; and dermal contact with soil, surface water, and ground water.« less

Method for fabricating light weight carbon-bonded carbon fiber composites

DOEpatents

Wrenn, Jr., George E.; Abbatiello, Leonard A.; Lewis, Jr., John

1989-01-01

Ultralight carbon-bonded carbon fiber composites of densities in the range of about 0.04 to 0.10 grams per cubic centimeter are fabricated by forming an aqueous slurry of carbonaceous fibers which include carbonized fibers and 0-50 weight percent fugitive fibers and a particulate thermosetting resin precursor. The slurry is brought into contact with a perforated mandrel and the water is drained from the slurry through the perforations at a controlled flow rate of about 0.03 to 0.30 liters per minutes per square inch of mandrel surface. The deposited billet of fibers and resin precursor is heated to cure the resin precursor to bind the fibers together, removed from the mandrel, and then the resin and fugitive fibers, if any, are carbonized.

Characteristics of coal mine ventilation air flows.

PubMed

Su, Shi; Chen, Hongwei; Teakle, Philip; Xue, Sheng

2008-01-01

Coal mine methane (CMM) is not only a greenhouse gas but also a wasted energy resource if not utilised. Underground coal mining is by far the most important source of fugitive methane emissions, and approximately 70% of all coal mining related methane is emitted to the atmosphere through mine ventilation air. Therefore, research and development on mine methane mitigation and utilisation now focuses on methane emitted from underground coal mines, in particular ventilation air methane (VAM) capture and utilisation. To date, most work has focused on the oxidation of very low concentration methane. These processes may be classified based on their combustion kinetic mechanisms into thermal oxidation and catalytic oxidation. VAM mitigation/utilisation technologies are generally divided into two basic categories: ancillary uses and principal uses. However, it is possible that the characteristics of ventilation air flows, for example the variations in methane concentration and the presence of certain compounds, which have not been reported so far, could make some potential VAM mitigation and utilisation technologies unfeasible if they cannot cope with the characteristics of mine site ventilation air flows. Therefore, it is important to understand the characteristics of mine ventilation air flows. Moreover, dust, hydrogen sulphide, sulphur dioxide, and other possible compounds emitted through mine ventilation air into the atmosphere are also pollutants. Therefore, this paper presents mine-site experimental results on the characteristics of mine ventilation air flows, including methane concentration and its variations, dust loadings, particle size, mineral matter of the dust, and other compounds in the ventilation air flows. The paper also discusses possible correlations between ventilation air characteristics and underground mining activities.

75 FR 29338 - Energy Efficiency of Natural Gas Infrastructure and Operations Conference; Final Notice of Public...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-25

... recovery projects and issues associated with fugitive methane. Bruce Hedman, ICF International, on behalf... associated with fugitive methane. Richard D. Murphy, S.V.P. Energy Solutions Services, National Grid, on...

40 CFR Table 2 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at New Sources

Code of Federal Regulations, 2010 CFR

2010-07-01

... Receivers at New Sources 2 Table 2 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 2 Table 2 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at New Sources Vessel...

40 CFR Table 2 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at New Sources

Code of Federal Regulations, 2011 CFR

2011-07-01

... Receivers at New Sources 2 Table 2 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 2 Table 2 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at New Sources Vessel...

40 CFR Table 1 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at Existing Sources

Code of Federal Regulations, 2010 CFR

2010-07-01

... Receivers at Existing Sources 1 Table 1 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 1 Table 1 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at Existing Sources...

40 CFR Table 1 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at Existing Sources

Code of Federal Regulations, 2011 CFR

2011-07-01

... Receivers at Existing Sources 1 Table 1 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 1 Table 1 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at Existing Sources...

40 CFR 52.920 - Identification of plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... New oil-effluent water separators 06/29/79 08/07/81, 46 FR 40188. 401 KAR 59:101 New bulk gasoline.../06/79 01/25/80, 45 FR 6092. 401 KAR 61:045 Existing oil-effluent water separators 06/29/79 08/07/81....11 Control of Open Burning 10/23/01 66 FR 53660 02/22/90 1.14 Control of Fugitive Particulate...

40 CFR Table 1 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at Existing Sources

Code of Federal Regulations, 2014 CFR

2014-07-01

... Receivers at Existing Sources 1 Table 1 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 1 Table 1 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at Existing Sources...

40 CFR Table 1 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at Existing Sources

Code of Federal Regulations, 2013 CFR

2013-07-01

... Receivers at Existing Sources 1 Table 1 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 1 Table 1 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at Existing Sources...

40 CFR Table 2 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at New Sources

Code of Federal Regulations, 2013 CFR

2013-07-01

... Receivers at New Sources 2 Table 2 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 2 Table 2 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at New Sources Vessel...

40 CFR Table 1 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at Existing Sources

Code of Federal Regulations, 2012 CFR

2012-07-01

... Receivers at Existing Sources 1 Table 1 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 1 Table 1 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at Existing Sources...

40 CFR Table 2 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at New Sources

Code of Federal Regulations, 2014 CFR

2014-07-01

... Receivers at New Sources 2 Table 2 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 2 Table 2 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at New Sources Vessel...

40 CFR Table 2 to Subpart V of... - Surge Control Vessels and Bottoms Receivers at New Sources

Code of Federal Regulations, 2012 CFR

2012-07-01

... Receivers at New Sources 2 Table 2 to Subpart V of Part 61 Protection of Environment ENVIRONMENTAL... POLLUTANTS National Emission Standard for Equipment Leaks (Fugitive Emission Sources) Pt. 61, Subpt. V, Table 2 Table 2 to Subpart V of Part 61—Surge Control Vessels and Bottoms Receivers at New Sources Vessel...

Social Science Libraries Section. Special Libraries Division. Papers.

ERIC Educational Resources Information Center

International Federation of Library Associations, The Hague (Netherlands).

Papers on social science documentation and information services presented at the 1982 International Federation of Library Associations (IFLA) conference include: (1) "Problems in the Availability of Some Social Science Publications," a discussion by Maurice B. Line (United Kingdom) of bibliographic control of fugitive literature in the…

Center for Corporate Climate Leadership: Direct Fugitive Emissions from Refrigeration, Air Conditioning, Fire Suppression, and Industrial Gases

EPA Pesticide Factsheets

This guidance document focuses on several fugitive emissions sources that are common for organizations in many sectors: refrigeration and air conditioningsystems, fire suppression systems, and the purchase and release of industrial gases.

Investigation of fugitive emissions from petrochemical transport barges using optical remote sensing

EPA Science Inventory

Recent airborne remote sensing survey data acquired with passive gas imaging equipment (PGIE), in this case infrared cameras, have shown potentially significant fugitive volatile organic carbon (VOC) emissions from petrochemical transport barges. The experiment found remote sens...

SPECTRAL MONITORING OF FUGITIVE CONTAMINANTS IN THE ENVIRONMENT

EPA Science Inventory

The accidental or intentional release of hazardous chemical substances into the environment is an inevitable consequence of anthropogenic activity. The detection, monitoring and remediation of fugitive contaminants is a major risk factor for human and ecological health and i...

Fugitive methane assessment with mobile and fence line sensors

EPA Science Inventory

There is no published abstract for this short panel talk. The panel presentation titled “Fugitive methane assessment with mobile and fence line sensors” provides a basic introduction to the topic of next generation sensor technologies for identifying and fixing emiss...

EVALUATION OF FUGITIVE EMISSIONS USING GROUND-BASED OPTICAL REMOTE SENSING TECHNOLOGY

EPA Science Inventory

EPA has developed and evaluated a method for characterizing fugitive emissions from large area sources. The method, known as radial plume mapping (RPM) uses multiple-beam, scanning, optical remote sensing (ORS) instrumentation such as open-path Fourier transform infrared spectro...

MEASUREMENT OF FUGITIVE EMISSIONS AT A BIOREACTOR LANDFILL

EPA Science Inventory

This report focuses on three field campaigns performed in 2002 and 2003 to measure fugitive emissions at a bioreactor landfill in Louisville, KY, using an open-path Fourier transform infrared spectrometer. The study uses optical remote sensing-radial plume mapping. The horizontal...

Method for fabricating light weight carbon-bonded carbon fiber composites

DOEpatents

Wrenn, G.E. Jr.; Abbatiello, L.A.; Lewis, J. Jr.

1987-06-17

The invention is directed to the fabrication of ultralight carbon- bonded carbon fiber composites of densities in the range of about 0. 04 to 0.10 grams per cubic centimeter. The composites are fabricated by forming an aqueous slurry of carbonaceous fibers which include carbonized fibers and 0-50 weight percent fugitive fibers and a particulate thermosetting resin precursor. The slurry is brought into contact with a perforated mandrel and the water is drained from the slurry through the perforations at a controlled flow rate of about 0. 03 to 0.30 liters per minutes per square inch of a mandrel surface. The deposited billet of fibers and resin precursor is heated to cure the resin precursor to bind the fibers together, removed from the mandrel, and then the resin and fugitive fibers, if any, are carbonized.

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... lead metal produced) from the aggregation of emissions discharged from the air pollution control... CATEGORIES National Emission Standards for Hazardous Air Pollutants for Primary Lead Smelting § 63.1543... reconstructed primary lead smelter shall discharge or cause to be discharged into the atmosphere lead compounds...

MEASUREMENT OF FUGITIVE EMISSIONS AT A LANDFILL PRACTICING LEACHATE RECIRCULATION AND AIR INJECTION

EPA Science Inventory

Recently research has begun on operating bioreactor landfills. The bioreactor process involves the injection of liquid into the waste mass to accelerate waste degradation. Arcadis and EPA conducted a fugitive emissions characterization study at the Three Rivers Solid Waste Techno...

FUGITIVE EMISSION SOURCES AND BATCH OPERATIONS IN SYNTHETIC ORGANIC CHEMICAL PRODUCTION

EPA Science Inventory

This survey report was developed for the EPA for use in assessing the potential magnitude of fugitive volatile organic compound (VOC) emissions from agitator seals, cooling towers and batch operations in the production of 378 designated chemicals. The information presented in thi...

Dust emissions created by low-level rotary-winged aircraft flight over desert surfaces

NASA Astrophysics Data System (ADS)

Gillies, J. A.; Etyemezian, V.; Kuhns, H.; McAlpine, J. D.; King, J.; Uppapalli, S.; Nikolich, G.; Engelbrecht, J.

2010-03-01

There is a dearth of information on dust emissions from sources that are unique to U.S. Department of Defense testing and training activities. Dust emissions of PM 10 and PM 2.5 from low-level rotary-winged aircraft travelling (rotor-blade ≈7 m above ground level) over two types of desert surfaces (i.e., relatively undisturbed desert pavement and disturbed desert soil surface) were characterized at the Yuma Proving Ground (Yuma, AZ) in May 2007. Fugitive emissions are created by the shear stress of the outflow of high speed air created by the rotor-blade. The strength of the emissions was observed to scale primarily as a function of forward travel speed of the aircraft. Speed affects dust emissions in two ways: 1) as speed increases, peak shear stress at the soil surface was observed to decline proportionally, and 2) as the helicopter's forward speed increases its residence time over any location on the surface diminishes, so the time the downward rotor-generated flow is acting upon that surface must also decrease. The state of the surface over which the travel occurs also affects the scale of the emissions. The disturbed desert test surface produced approximately an order of magnitude greater emission than the undisturbed surface. Based on the measured emission rates for the test aircraft and the established scaling relationships, a rotary-winged aircraft similar to the test aircraft traveling 30 km h -1 over the disturbed surface would need to travel 4 km to produce emissions equivalent to one kilometer of travel by a light wheeled military vehicle also traveling at 30 km h -1 on an unpaved road. As rotary-winged aircraft activity is substantially less than that of off-road vehicle military testing and training activities it is likely that this source is small compared to emissions created by ground-based vehicle movements.

Mobile monitoring of fugitive methane emissions from natural gas consumer industries

EPA Science Inventory

Natural gas is used as a feedstock for major industrial processes, such as ammonia and fertilizer production. However, fugitive methane emissions from many major end-use sectors of the natural gas supply chain have not yet been well quantified. This presentation introduces new m...

The Mobile Monitoring of fugitive methane emissions from natural gas consumer industries

EPA Science Inventory

Natural gas is used as a feedstock for major industrial processes, such as ammonia and fertilizer production. However, fugitive methane emissions from many major end-use sectors of the natural gas supply chain have not been quantified yet. This presentation introduces new tools ...

OPEN PATH TUNABLE DIODE LASER ABSORPTION SPECTROSCOPY FOR ACQUISITION OF FUGITIVE EMISSION FLUX DATA

EPA Science Inventory

Air pollutant emission from unconfined sources is an increasingly important environmental issue. The U.S. EPA has developed a gorund-based optical remote sensing method that enables direct measurement of fugitive emission flux from large area sources. Open-path Fourier transfor...

40 CFR 60.441 - Definitions and symbols.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Fugitive volatile organic compounds means any volatile organic compounds which are emitted from the coating... capture fugitive volatile organic compounds. Oven means a chamber which uses heat or irradiation to bake... or label product. Solvent applied in the coating means all organic solvent contained in the adhesive...

40 CFR 60.441 - Definitions and symbols.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Fugitive volatile organic compounds means any volatile organic compounds which are emitted from the coating... capture fugitive volatile organic compounds. Oven means a chamber which uses heat or irradiation to bake... or label product. Solvent applied in the coating means all organic solvent contained in the adhesive...

40 CFR 60.441 - Definitions and symbols.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Fugitive volatile organic compounds means any volatile organic compounds which are emitted from the coating... capture fugitive volatile organic compounds. Oven means a chamber which uses heat or irradiation to bake... or label product. Solvent applied in the coating means all organic solvent contained in the adhesive...

40 CFR 60.441 - Definitions and symbols.

Code of Federal Regulations, 2014 CFR

2014-07-01

... = the weight fraction of organics applied of each coating (i) applied during a calendar month as.... Fugitive volatile organic compounds means any volatile organic compounds which are emitted from the coating... capture fugitive volatile organic compounds. Oven means a chamber which uses heat or irradiation to bake...

40 CFR 63.544 - Standards for process fugitive sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Smelting furnace and dryer charging hoppers, chutes, and skip hoists; (2) Smelting furnace lead taps, and molds during tapping; (3) Smelting furnace slag taps, and molds during tapping; (4) Refining kettles; (5) Dryer transition pieces; and (6) Agglomerating furnace product taps. (b) Process fugitive emission...

Queer Histories: Exploring Fugitive Forms of Social Knowledge.

ERIC Educational Resources Information Center

Hill, Bob, Ed.

This document contains eight papers from a conference on fugitive forms of social knowledge that was sponsored by the Adult Education Research Conference (AERC) Lesbian, Gay, Bisexual, Transgender, Queer, and Allies Caucus. The welcome address, "Working Memory at AERC: A Queer Welcome...and a Retrospective" (Bob Hill), explores the…

A Walk on the Underground Railroad.

ERIC Educational Resources Information Center

Cohen, Anthony

2001-01-01

Describes one historian's search for information on the Underground Railroad, retracing on foot one of the routes formerly traveled by fugitives, seeking historical societies and libraries in each town, and interviewing descendants of slaves. He also had himself boxed up and smuggled onto a train to simulate the situation of one fugitive. A…

Performance Evaluations and Quality Validation System for Optical Gas Imaging Cameras That Visualize Fugitive Hydrocarbon Gas Emissions

EPA Science Inventory

Optical gas imaging (OGI) cameras have the unique ability to exploit the electromagnetic properties of fugitive chemical vapors to make invisible gases visible. This ability is extremely useful for industrial facilities trying to mitigate product losses from escaping gas and fac...

76 FR 23489 - Prevention of Significant Deterioration (PSD) and Nonattainment New Source Review (NSR...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-27

...): Reconsideration of Inclusion of Fugitive Emissions; Interim Rule; Stay and Revisions AGENCY: Environmental... (PSD) and Nonattainment New Source Review (NSR): Reconsideration of Inclusion of Fugitive Emissions... inclusion in the public docket. Information so marked will not be disclosed except in accordance with...

Estimation of point source fugitive emission rates from a single sensor time series: a conditionally-sampled Gaussian plume reconstruction

EPA Science Inventory

This paper presents a technique for determining the trace gas emission rate from a point source. The technique was tested using data from controlled methane release experiments and from measurement downwind of a natural gas production facility in Wyoming. Concentration measuremen...

Fugitive and Codified Knowledge: Implications for Communities Struggling to Control the Meaning of Local Environmental Hazards

ERIC Educational Resources Information Center

Hill, Robert

2004-01-01

The purpose of this qualitative research was to determine the ways that knowledge is constructed and used by emergent citizen's groups (ECGs are grassroots, action-oriented, problem-solving groups) engaged in environmental conflicts, and by a state government environmental regulatory agency that interfaced with them. Four…

Quantifying Fugitive Methane Emissions from Natural Gas Production with Mobile Technology

NASA Astrophysics Data System (ADS)

Tsai, T.; Rella, C.; Crosson, E.

2013-12-01

Quantification of fugitive methane (CH4) emissions to determine the environmental impact of natural gas production is challenging with current methods. We present a new mobile method known as the Plume Scanner that can quickly quantify CH4 emissions of point sources. The Plume Scanner is a direct measurement technique which utilizes a mobile Picarro cavity ring-down spectrometer and a gas sampling system based on AirCore technology [1]. As the Plume Scanner vehicle drives through the plume, the air is simultaneously sampled at four different heights, and therefore, the spatial CH4 distribution can be captured (Fig. 1). The flux of the plume is then determined by multiplying the spatial CH4 distribution data with the anemometer measurements. In this way, fugitive emission rates of highly localized sources such as natural gas production pads can be made quickly (~7 min). Verification with controlled CH4 releases demonstrate that under stable atmospheric conditions (Pasquill stability class is C or greater), the Plume Scanner measurements have an error of 2% and a repeatability of 15% [2]. Under unstable atmospheric conditions (Class A or B), the error is 6%, and the repeatability increases to 70% due to the variability of wind conditions. Over two weeks, 275 facilities in the Barnett Shale were surveyed from public roads by sampling the air for elevations in CH4 concentration, and 77% were found leaking. Emissions from 52 sites have been quantified with the Plume Scanner (Fig. 2), and the total emission is 4,900 liters per min (lpm) or 39,000 metric tons/yr CO2e. 1. Karion, A., C. Sweeney, P. Tans, and T. Newberger (2010), AirCore: An innovative atmospheric sampling system, J. Atmos. Oceanic Tech, 27, 1839-1853. 2. F. Pasquill (1961), The estimation of the dispersion of wind borne material, Meterol. Mag., 90(1063), 33-49 Figure 1. Plume Scanner Cartoon Figure 2. Distribution of methane fugitive emissions with error bars associated with the Pasquill stability classes drawn for reference.

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado, Utah, and Texas using mobile isotopic methane analysis based on Cavity Ringdown Spectroscopy

NASA Astrophysics Data System (ADS)

Rella, Chris; Winkler, Renato; Sweeney, Colm; Karion, Anna; Petron, Gabrielle; Crosson, Eric

2014-05-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of carbon dioxide emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation, provided that the fugitive emissions of methane are kept under control. A key step in assessing these emissions in a given region is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis, using the isotopic carbon signature to distinguish between natural gas and landfills or ruminants. We present measurements of methane using a mobile spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in three intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, the Uintah basin in Utah, and the Barnett Shale in Texas. Performance of the CRDS isotope analyzer is presented, including precision, calibration, stability, and the potential for measurement bias due to other atmospheric constituents. Mobile isotope measurements of individual sources and in the nocturnal boundary layer have been combined to establish the fraction of the observed methane emissions that can be attributed to natural gas activities. The fraction of total methane emissions in the Denver-Julesburg basin attributed to natural gas emissions is 78 +/- 13%. In the Uinta basin, which has no other significant sources of methane, the fraction is 96% +/- 15%. In addition, results from the Barnett shale are presented, which includes a major urban center (Dallas / Ft. Worth). Methane emissions in this region are spatially highly heterogeneous. Spatially-resolved isotope and concentration measurements are interpreted using a simple emissions model to arrive at an overall isotope ratio for the region.

40 CFR 63.7351 - Who implements and enforces this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and...-product coke oven battery with vertical flues, fugitive pushing emissions in § 63.7292(a) for a by-product coke oven battery with horizontal flues, fugitive pushing emissions in § 63.7293 for a non-recovery...

40 CFR 63.7351 - Who implements and enforces this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and...-product coke oven battery with vertical flues, fugitive pushing emissions in § 63.7292(a) for a by-product coke oven battery with horizontal flues, fugitive pushing emissions in § 63.7293 for a non-recovery...

40 CFR 63.7351 - Who implements and enforces this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and...-product coke oven battery with vertical flues, fugitive pushing emissions in § 63.7292(a) for a by-product coke oven battery with horizontal flues, fugitive pushing emissions in § 63.7293 for a non-recovery...

40 CFR 63.7351 - Who implements and enforces this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and...-product coke oven battery with vertical flues, fugitive pushing emissions in § 63.7292(a) for a by-product coke oven battery with horizontal flues, fugitive pushing emissions in § 63.7293 for a non-recovery...

Bayesian Estimation of Fugitive Methane Point Source Emission Rates from a SingleDownwind High-Frequency Gas Sensor

EPA Science Inventory

Bayesian Estimation of Fugitive Methane Point Source Emission Rates from a Single Downwind High-Frequency Gas Sensor With the tremendous advances in onshore oil and gas exploration and production (E&P) capability comes the realization that new tools are needed to support env...

CHARACTERIZATION OF THE FUGITIVE MERCURY EMISSIONS AT A CHLOR-ALKALI PLANT. OVERALL STUDY DESIGN

EPA Science Inventory

The paper discusses a detailed emissions measurement campaign that was conducted over a 9-day period within a mercury (Hg) cell chlor-alkali plant in the southeastern United States (U.S.). The principal focus of this study was to measure fugitive (non-ducted) airborne Hg emission...

FUGITIVE EMISSION REDUCTIONS DUE TO THE USE OF ENCLOSED DOCTOR BLADE SYSTEMS IN THE FLEXOGRAPHIC AND ROTOGRAVURE PRINTING INDUSTRIES

EPA Science Inventory

The report gives results of a quantification of the level of fugitive emission reductions resulting from the use of enclosed doctor blade (EDB) systems in place of traditional ink feed systems at flexographic and rotogravure printing operations. An EDB system is an innovative ink...

The Fugitive Literature of Acid Rain: Making Use of Nonconventional Information Sources in a Vertical File.

ERIC Educational Resources Information Center

Lovenburg, Susan L.; Stoss, Frederick W.

1988-01-01

Discusses the advantages of vertical file collections for nonconventional literature, and describes the classification scheme used for fugitive literature by the Acid Rain Information Clearinghouse at the Center for Environmental Information. An annotated list of organizations and examples of titles they offer is provided. (8 notes with…

40 CFR 60.55b - Standards for municipal waste combustor fugitive ash emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Performance for Large Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for municipal waste combustor... municipal waste combustor fugitive ash emissions. (a) On and after the date on which the initial performance...

40 CFR 60.55b - Standards for municipal waste combustor fugitive ash emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Performance for Large Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for municipal waste combustor... municipal waste combustor fugitive ash emissions. (a) On and after the date on which the initial performance...

77 FR 19153 - Nonpayment of Benefits to Fugitive Felons and Probation or Parole Violators

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-30

... SOCIAL SECURITY ADMINISTRATION 20 CFR Parts 404 and 416 [Docket No. SSA 2006-0173] RIN 0960-AG12 Nonpayment of Benefits to Fugitive Felons and Probation or Parole Violators AGENCY: Social Security Administration. ACTION: Proposed rules; withdrawal. SUMMARY: We are withdrawing the proposed rules we published...

Dust control research for SEI. [Space Exploration Initiative

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Harris, Jeffrey R.

1992-01-01

A study, at NASA Johnson Space Center, of dust control requirements for surface habitats has focused on identification of the dust problem, identifying dust control techniques and dust control technology areas requiring research development. This research was performed for the Surface Habitats and Construction (SHAC) technology area. Dust control consists of two problems: (1) how to keep it out of the habitat; and (2) once the habitat or airlock is contaminated with dust, how to collect it. This paper describes the dust environment, the Apollo experience and dust control methods used, future EVA operational considerations, and dust control concepts for surface habitats.

Fugitive Emissions from Conventional and Hydraulically Fractured Natural Gas Developments in Western Canada

NASA Astrophysics Data System (ADS)

Atherton, E. E.; Risk, D. A.; Lavoie, M.; Marshall, A. D.; Baillie, J.; Williams, J. P.

2015-12-01

Presently, fugitive emissions released into the atmosphere during the completion and production of oil and gas wells are poorly regulated within Canada. Some possible upstream sources of these emissions include flowback during well completions, liquid unloading, chemical injection pumps, and equipment leaks. The environmental benefits of combusting natural gas compared to oil or coal are negated if methane leakages surpass 3.2% of total production, so it is important to have a thorough understanding of these fugitive emissions. This study compares atmospheric leakage pathways of methane and other fugitive gases in both conventional and unconventional oil and gas developments in Western Canada to help fill this knowledge gap. Over 5000 kilometers of mobile survey campaigns were completed in carefully selected developments in the Montney shale play in British Columbia, and in conventional oil fields in Alberta. These sites are developed by more than 25 different operators. High precision laser and UV fluorescence gas analyzers were used to gather geolocated trace gas concentrations at a frequency of 1 Hz while driving. These data were processed with an adaptive technique to compensate for fluctuations in background concentrations for each gas. The residual excess concentrations were compositionally fingerprinted on the basis of the expected gas ratios for potential emission sites in order to definitively attribute anomalies to infrastructural leak sources. Preliminary results from the mobile surveys of both conventional and unconventional oil and gas sites are presented here. Pathways of methane and other fugitive gases are mapped to their respective sources, identifying common causes of emissions leaks across the oil and gas industry. This is the first bottom-up study of fugitive emissions from Canadian energy developments to produce publicly available data. These findings are significant to operators interested in lowering emissions for economic benefit, as well as public and governmental groups looking to become more informed on the impacts of oil and gas developments in Canada.

Plutonium release from the 903 pad at Rocky Flats.

PubMed

Mongan, T R; Ripple, S R; Winges, K D

1996-10-01

The Colorado Department of Public Health and Environment (CDH) sponsored a study to reconstruct contaminant doses to the public from operations at the Rocky Flats nuclear weapons plant. This analysis of the accidental release of plutonium from the area known as the 903 Pad is part of the CDH study. In the 1950's and 1960's, 55-gallon drums of waste oil contaminated with plutonium, and uranium were stored outdoors at the 903 Pad. The drums corroded, leaking contaminated oil onto soil subsequently carried off-site by the wind. The plutonium release is estimated using environmental data from the 1960's and 1970's and an atmospheric transport model for fugitive dust. The best estimate of total plutonium release to areas beyond plant-owned property is about 0.26 TBq (7 Ci). Off-site airborne concentrations and deposition of plutonium are estimated for dose calculation purposes. The best estimate of the highest predicted off-site effective dose is approximately 72 microSv (7.2 mrem).

EVALUATION OF FUGITIVE EMISSIONS AT A FORMER LANDFILL SITE IN COLORADO SPRINGS, COLORADO, USING GROUND-BASED OPTICAL REMOTE SENSING TECHNOLOGY

EPA Science Inventory

This report details a measurement campaign conducted using the Radial Plume Mapping (RPM) method and optical remote sensing technologies to characterize fugitive emissions. This work was funded by EPAs Monitoring and Measurement for the 21st Century Initiative, or 21M2. The si...

Document Preparation (for Filming). ERIC Processing Manual, Appendix B.

ERIC Educational Resources Information Center

Brandhorst, Ted, Ed.; And Others

The technical report or "fugitive" literature collected by ERIC is produced using a wide variety of printing techniques, many formats, and variable degrees of quality control. Since the documents processed by ERIC go on to be microfilmed and reproduced in microfiche and paper copy for sale to users, it is essential that the ERIC document…

40 CFR 52.781 - Rules and regulations.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) A part of the second sentence in section 3, APC-17, which states “Where there is a violation or... pollution control equipment shall comply with th (c)-(d) [Reserved] (e) Section 2(d) of APC-20, Fugitive...) Subsections 3(b)(3) and 3(b)(5) of APC-2 (May 18, 1977) are disapproved because they are unenforceable within...

Race towards Freedom: W.E.B. Du Bois and the Tradition of Fugitive Black Study

ERIC Educational Resources Information Center

Tinson, Christopher M.

2017-01-01

This essay centers the defense of black educational possibility in the work of historian, pioneering sociologist, and scholar, W.E.B. Du Bois (1868-1963) as a conduit igniting what critical social theorists Stefano Harney and Fred Moten (2013) call Fugitive Black Study. The critical appreciation of Du Bois forces us to consider the weight of…

Identifying sources of fugitive emissions in industrial facilities using trajectory statistical methods

NASA Astrophysics Data System (ADS)

Brereton, Carol A.; Johnson, Matthew R.

2012-05-01

Fugitive pollutant sources from the oil and gas industry are typically quite difficult to find within industrial plants and refineries, yet they are a significant contributor of global greenhouse gas emissions. A novel approach for locating fugitive emission sources using computationally efficient trajectory statistical methods (TSM) has been investigated in detailed proof-of-concept simulations. Four TSMs were examined in a variety of source emissions scenarios developed using transient CFD simulations on the simplified geometry of an actual gas plant: potential source contribution function (PSCF), concentration weighted trajectory (CWT), residence time weighted concentration (RTWC), and quantitative transport bias analysis (QTBA). Quantitative comparisons were made using a correlation measure based on search area from the source(s). PSCF, CWT and RTWC could all distinguish areas near major sources from the surroundings. QTBA successfully located sources in only some cases, even when provided with a large data set. RTWC, given sufficient domain trajectory coverage, distinguished source areas best, but otherwise could produce false source predictions. Using RTWC in conjunction with CWT could overcome this issue as well as reduce sensitivity to noise in the data. The results demonstrate that TSMs are a promising approach for identifying fugitive emissions sources within complex facility geometries.

Determining a Criminal Defendant's Competency to Proceed With an Extradition Hearing.

PubMed

Piel, Jennifer; Finkle, Michael J; Giske, Megan; Leong, Gregory B

2015-06-01

When a criminal defendant flees from one state (often referred to as the requesting state) to another (often referred to as the asylum state), the requesting state can demand that the asylum state return the defendant through a process called extradition. Only a handful of states have considered a fugitive's right to be competent to proceed with an extradition hearing. Those states fall into three categories. Some states apply the same standard as in criminal trial competency cases. Others apply a more limited competency standard. Two have found that a fugitive has no right to be competent to proceed in an extradition hearing. The particular legal test adopted affects the nature and scope of the competency evaluation conducted by the psychiatrist or psychologist in the extradition hearing. In addition, we are not aware of any state that has considered what happens to the fugitive if he is ultimately found not competent to proceed. Legislation, either state by state or through amendments to the Uniform Criminal Extradition Act, can provide the legal and psychiatric communities with guidance in assessing competency initially and in taking appropriate steps if the fugitive is ultimately found not competent. © 2015 American Academy of Psychiatry and the Law.

Impact of fugitive sources and meteorological parameters on vertical distribution of particulate matter over the industrial agglomeration.

PubMed

Štrbová, Kristína; Raclavská, Helena; Bílek, Jiří

2017-12-01

The aim of the study was to characterize vertical distribution of particulate matter, in an area well known by highest air pollution levels in Europe. A balloon filled with helium with measuring instrumentation was used for vertical observation of air pollution over the fugitive sources in Moravian-Silesian metropolitan area during spring and summer. Synchronously, selected meteorological parameters were recorded together with particulate matter for exploration its relationship with particulate matter. Concentrations of particulate matter in the vertical profile were significantly higher in the spring than in the summer. Significant effect of fugitive sources was observed up to the altitude ∼255 m (∼45 m above ground) in both seasons. The presence of inversion layer was observed at the altitude ∼350 m (120-135 m above ground) at locations with major source traffic load. Both particulate matter concentrations and number of particles for the selected particle sizes decreased with increasing height. Strong correlation of particulate matter with meteorological parameters was not observed. The study represents the first attempt to assess the vertical profile over the fugitive emission sources - old environmental burdens in industrial region. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fugitive from Labor Cases: Henry Garnett (1850) and Moses Honner (1860). The Constitution Community: Civil War and Reconstruction (1850-1870).

ERIC Educational Resources Information Center

Lawlor, John M., Jr.

The cases of Henry Garnett and Moses Honner bookend the 1850s, a decade of intensifying political crisis that was deeply connected to the institution of slavery. In both court actions, which were tried in the Third Circuit Court, Eastern District, Philadelphia, Pennsylvania, the defendants were charged with being "fugitives from labor."…

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Code of Federal Regulations, 2010 CFR

2010-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Code of Federal Regulations, 2013 CFR

2013-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Code of Federal Regulations, 2012 CFR

2012-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Code of Federal Regulations, 2014 CFR

2014-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Code of Federal Regulations, 2011 CFR

2011-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

Organic Components and Elemental Carbon in Soils and Ambient Particles near Phoenix, AZ

NASA Astrophysics Data System (ADS)

Fraser, M. P.; Jia, Y.; Clements, A.

2008-12-01

In the desert southwest, fugitive dust emissions contribute significantly to ambient aerosol concentrations. Wind erosion from the arid land is a primary contributor to ambient particulate matter (PM) concentrations but, in regions including Central Arizona, desert lands have been converted for agriculture use and thus agriculture processes constitute another contributor. As the metropolitan Phoenix region expands into these agricultural lands, urban sources and construction also contributes to the ambient PM load. In an effort to identify and access relative contribution of these and other major PM sources in the region, a series of ambient PM samples and soil samples were collected near Higley, AZ, a suburb of Phoenix which has seen rapid urbanization onto agricultural lands between January and May 2008. The soil samples collected were resuspended and samples of resuspended dust were collected to represent particles smaller than 2.5 microns and 10 microns in aerodynamic diameter (PM2.5 and PM10 respectively). The size segregated soil and ambient PM samples were analyzed for bulk mass, elemental and organic carbon content, and a number of specific compounds including ions, metals, alkanes, organic acids, polycyclic aromatic hydrocarbons, and saccharides. The saccharide contribution to soil organic carbon has been studied to elucidate key factors in the soil carbon balance and markers have been developed for tracing fungal metabolites, plant growth and budding and organic matter decay. Using organic markers, the contribution of various sources to PM10 and PM2.5 levels have been determined by positive matrix factorization (PMF) of the ambient aerosol marker concentrations quantified from PM samples. Subsequently, samples of local soil from native and agricultural fields and local roadways wers size- segregated and analyzed in an effort to create a source profile for the dust in the area. A chemical mass balance model has been used to compare with the PMF results where sampled and resuspended agricultural soil, native soil and road dusts are used to characterize direct emissions of these sources to ambient fine and coarse particulate matter.

30 CFR 72.630 - Drill dust control at underground areas of underground mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... dust control at underground areas of underground mines. (a) Dust resulting from drilling in rock shall... condition. Dust collectors approved under Part 33—Dust Collectors for Use in Connection with Rock Drilling... the purpose of this section. (c) Water control. Water used to control dust from drilling rock shall be...

30 CFR 72.630 - Drill dust control at underground areas of underground mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... dust control at underground areas of underground mines. (a) Dust resulting from drilling in rock shall... condition. Dust collectors approved under Part 33—Dust Collectors for Use in Connection with Rock Drilling... the purpose of this section. (c) Water control. Water used to control dust from drilling rock shall be...

Differential Absorption Lidar Measurements of Fugitive Benzene Emissions

NASA Astrophysics Data System (ADS)

Robinson, R. A.; Innocenti, F.; Helmore, J.; Gardiner, T.; Finlayson, A.; Connor, A.

2016-12-01

The Differential Absorption Lidar (DIAL) technique is based on the optical analogue of radar; lidar (light detection and ranging). It provides the capability to remotely measure the concentration and spatial distribution of compounds in the atmosphere. The ability to scan the optical measurement beam throughout the atmosphere enables pollutant concentrations to be mapped, and emission fluxes to be determined when combined with wind data. The NPL DIAL systems can operate in the UV and infrared spectral, enabling the measurement of a range of air pollutants and GHGs including hazardous air pollutants such as benzene. The mobile ground based DIAL systems developed at NPL for pollution monitoring have been used for over 25 years. They have been deployed for routine monitoring, emission factor studies, research investigations and targeted monitoring campaigns. More recently the NPL DIAL has been used in studies to validate other monitoring techniques. In support of this capability, NPL have developed a portable, configurable controlled release system (CRF) able to simulate emissions from typical sources. This has been developed to enable the validation and assessment of fugitive emission monitoring techniques. Following a brief summary of the technique, we outline recent developments in the use of DIAL for monitoring fugitive and diffuse emissions, including the development of a European Standard Method for fugitive emission monitoring. We will present the results of a number of validation exercises using the CRF presenting an update on the performance of DIAL for emission quantification and discuss the wider validation of novel technologies. We will report on recent measurements of the emissions of benzene from industrial sites including a large scale emissions monitoring study carried out by the South Coast Air Quality Management District (SCAQMD) and will report on the measurement of emissions from petrochemical facilities and examine an example of the identification and quantification of a significant benzene release from a facility in Europe. We will discuss the use of advanced techniques such as DIAL in support of the recently introduced EPA refinery rule (and the long term sampling approach in EPA method 325) and explore the role these techniques can have in providing improved data on emissions.

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado, Utah, and Texas using mobile δ13CH4 analysis

NASA Astrophysics Data System (ADS)

Rella, C.; Crosson, E.; Petron, G.; Sweeney, C.; Karion, A.

2013-12-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of CO2 emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation, provided that the fugitive emissions of methane are kept under control. A key step in assessing these emissions in a given region is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis, using the δ13CH4 signature to distinguish between natural gas and landfills or ruminants. We present measurements of mobile field δ13CH4 using a spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in three intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, the Uintah basin in Utah, and the Barnett Shale in Texas. Mobile isotope measurements of individual sources and in the nocturnal boundary layer have been combined to establish the fraction of the observed methane emissions that can be attributed to natural gas activities. The fraction of total methane emissions in the Denver-Julesburg basin attributed to natural gas emissions is 78 +/- 13%. In the Uinta basin, which has no other significant sources of methane, the fraction is 96% +/- 15%. In addition, results from the Barnett shale are presented, which includes a major urban center (Dallas / Ft. Worth). Methane emissions in this region are spatially highly heterogeneous. Spatially-resolved isotope and concentration measurements are interpreted using a simple emissions model to arrive at an overall isotope ratio for the region. (left panel) Distribution of oil and gas well pads (yellow) and landfills (blue) in the Dallas / Ft. Worth area. Mobile nocturnal measurements of methane are shown in red, indicating a strong degree of source heterogeneity. (right panel) Histogram of individual isotopic source signatures, showing distinct signatures for landfills (red) and oil and gas sources (green).

Portable air pollution control equipment for the control of toxic particulate emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chaurushia, A.; Odabashian, S.; Busch, E.

1997-12-31

Chromium VI (Cr VI) has been identified by the environmental regulatory agencies as a potent carcinogen among eleven heavy metals. A threshold level of 0.0001 lb/year for Cr VI emissions has been established by the California Air Resources Board for reporting under Assembly Bill 2588. A need for an innovative control technology to reduce fugitive emissions of Cr VI was identified during the Air Toxic Emissions Reduction Program at Northrop Grumman Military Aircraft Systems Division (NGMASD). NGMASD operates an aircraft assembly facility in El Segundo, CA. Nearly all of the aircraft components are coated with a protective coating (primer) priormore » to assembly. The primer has Cr VI as a component for its excellent corrosion resistance property. The complex assembly process requires fasteners which also need primer coating. Therefore, NGMASD utilizes High Volume Low Pressure (HVLP) guns for the touch-up spray coating operations. During the touch-up spray coating operations, Cr VI particles are atomized and transferred to the aircraft surface. The South Coast Air Quality Management District (SCAQMD) has determined that the HVLP gun transfers 65% of the paint particles onto the substrate and the remaining 35% are emitted as an overspray if air pollution controls are not applied. NGMASD has developed the Portable Air Pollution Control Equipment (PAPCE) to capture and control the overspray in order to reduce fugitive Cr VI emissions from the touch-up spray coating operations. A source test was performed per SCAQMD guidelines and the final report has been approved by the SCAQMD.« less

Spatial and temporal patterns in trace element deposition to lakes in the Athabasca oil sands region (Alberta, Canada)

NASA Astrophysics Data System (ADS)

Cooke, Colin A.; Kirk, Jane L.; Muir, Derek C. G.; Wiklund, Johan A.; Wang, Xiaowa; Gleason, Amber; Evans, Marlene S.

2017-12-01

The mining and processing of the Athabasca oil sands (Alberta, Canada) has been occurring for decades; however, a lack of consistent regional monitoring has obscured the long-term environmental impact. Here, we present sediment core results to reconstruct spatial and temporal patterns in trace element deposition to lakes in the Athabasca oil sands region. Early mining operations (during the 1970s and 1980s) led to elevated V and Pb inputs to lakes located <50 km from mining operations. Subsequent improvements to mining and upgrading technologies since the 1980s have reduced V and Pb loading to near background levels at many sites. In contrast, Hg deposition increased by a factor of ~3 to all 20 lakes over the 20th century, reflecting global-scale patterns in atmospheric Hg emissions. Base cation deposition (from fugitive dust emissions) has not measurably impacted regional lake sediments. Instead, results from a principal components analysis suggest that the presence of carbonate bedrock underlying lakes located close to development appears to exert a first-order control over lake sediment base cation concentrations and overall lake sediment geochemical composition. Trace element concentrations generally did not exceed Canadian sediment quality guidelines, and no spatial or temporal trends were observed in the frequency of guideline exceedence. Our results demonstrate that early mining efforts had an even greater impact on trace element cycling than has been appreciated previously, placing recent monitoring efforts in a critical long-term context.

Public-health assessment for Mottolo Pig Farm, Raymond, Rockingham County, New Hampshire, Region 1. CERCLIS NO. NHD980503361. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-07-20

The Mottolo Pig Farm National Priorities List (NPL) Site is located east of Blueberry Hill Road, in Rockingham County, approximately three miles west of the center of Raymond, New Hampshire. Contamination at the Mottolo Pig Farm Site includes contaminated groundwater, soil, surface water, and sediments. Site contaminants consist primarily of various volatile organic compounds (VOCs). Acid and base/neutral extractable compounds (ABNs) and metals have also been identified at the site. The site was initially discovered in April of 1979 and the U.S. Environmental Protection Agency (EPA) began an emergency action to remove buried drums and pails at the site inmore » September of 1980. There are no known documented completed exposure pathways for contaminated media present at the Mottolo Pig Farm Site. Exposure pathways of potential concern include direct contact with contaminated on-site soils and surface waters; inhalation of contaminated on-site soils as fugitive dust; and incidental ingestion of contaminated on-site soils and surface waters.« less

Health assessment for Shaw Avenue Dump Site, Charles City, Iowa, Region 7 (amended). CERCLIS No. IAD980630560. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-12-07

The Shaw Avenue Dump Site is listed by the U.S. Environmental Protection Agency (USEPA) on the National Priorities List (NPL). The 8-acre city dump site, consisting of three waste disposal areas, is located in the southeast edge of Charles City approximately 500 feet east of the Cedar River. The three disposal areas are no longer in use and have been covered with soil and are vegetated. Arsenic is the contaminant of concern at the Shaw Avenue Dump Site. On-site soil samples collected in 1981 contained concentrations of arsenic that ranged from 4-820 mg/kg. On-site groundwater, surface water, and air analysesmore » were not conducted in previous investigations. From the available information, this site is considered to be of public health concern because of the potential risk to human health caused by possible exposure to hazardous substances via ingestion of groundwater, soil, and surface water; inhalation of fugitive dust; and dermal contact with soil, surface water, and groundwater.« less

Quantitation of Japanese cedar pollen and radiocesium adhered to nonwoven fabric masks worn by the general population.

PubMed

Higaki, Shogo; Shirai, Hideharu; Hirota, Masahiro; Takeda, Eisuke; Yano, Yukiko; Shibata, Akira; Mishima, Yoshitaka; Yamamoto, Hiromi; Miyazawa, Kiyoshi

2014-08-01

In the spring of 2012, a year after the Fukushima Daiichi nuclear disaster, radiocesium-contaminated Japanese cedar pollen may have caused internal exposure to the general population by inhalation. To determine if pollen had been contaminated through uptake of radiocesium by Japanese cedars and was therefore contributing to inhalation doses, the authors measured radiocesium and Japanese cedar pollen adhered to masks worn by 68 human subjects residing in eastern Japan, including Fukushima prefecture, for 8 wk in the spring of 2012. The maximum cumulative Cs and Cs radioactivities on masks worn by an individual were 21 ± 0.36 Bq and 15 ± 0.22 Bq, respectively, and the estimated effective dose during the 8 wk was 0.494 μSv. The average estimated effective dose during the 8 wk was 0.149 μSv in Fukushima prefecture and 0.015 μSv in other prefectures, including Tokyo metropolitan. The correlation between radiocesium activity and the Japanese cedar pollen count was moderate. However, imaging-plate and light microscopy observations showed that the main source of radiocesium adhered to masks was fugitive dust.

On-Site Incineration of Contaminated Soil: A Study into U.S. Navy Applications

DTIC Science & Technology

1991-08-01

venturi scrubber Minimum water flow rate and p1l to absorber Minimum water/alkaline reagent flow to dry scrubber Minimum particulate scrubber blowdown...remove hydrochloric acid and sulfur dioxide from flue gases using, for example, wet scrubbers and limestone adsorption towers, respectively. Modified...Reagent preparation 8) Bllending 26) Fugitive emission control 9) Pretreatment 27) Scrubber liquid cooling 10) Blended and pretreated solid waste

RHIC AND THE PURSUIT OF THE QUARK-GLUON PLASMA.

DOE Office of Scientific and Technical Information (OSTI.GOV)

MITCHELL,J.T.

2001-07-25

There is a fugitive on the loose. Its name is Quark-Gluon Plasma, alias the QGP. The QGP is a known informant with knowledge about the fundamental building blocks of nature that we wish to extract. This briefing will outline the status of the pursuit of the elusive QGP. We will cover what makes the QGP tick, its modus operandi, details on how we plan to hunt the fugitive down, and our level of success thus far.

Dust Plume Modeling at Fort Bliss: Full Training Scenario

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chapman, Elaine G.; Rishel, Jeremy P.; Rutz, Frederick C.

2006-09-26

The potential for air quality impacts from heavy mechanized vehicles operating in the training ranges and on the unpaved main supply routes at Fort Bliss is being investigated. The investigation uses the atmospheric modeling system DUSTRAN to simulate fugitive dust emission and dispersion from typical activities occurring on the installation. This report conveys the results of DUSTRAN simulations conducted using a “Full Training” scenario developed by Fort Bliss personnel. he Full Training scenario includes simultaneous off-road activities of two full Heavy Brigade Combat Teams (HCBTs) and one HCBT battalion on three training ranges. Simulations were conducted for the six-day period,more » April 25-30, 2005, using previously archived meteorological records. Simulation results are presented in the form of 24-hour average PM10 plots and peak 1-hour PM10 concentration plots, where the concentrations represent contributions resulting from the specified military vehicular activities, not total ambient PM10 concentrations. Results indicate that the highest PM10 contribution concentrations occurred on April 30 when winds were light and variable. Under such conditions, lofted particulates generated by vehicular movement stay in the area of generation and are not readily dispersed. The effect of training duration was investigated by comparing simulations with vehicular activity extending over a ten hour period (0700 to 1700 MST) with simulations where vehicular activity was compressed into a one hour period (0700 to 0800 MST). Compressing all vehicular activity into one hour led to higher peak one-hour and 24-hour average concentration contributions, often substantially higher.« less

Summary, synthesis, and significance: Chapter 6

USGS Publications Warehouse

Esque, Todd C.; Nussear, Kenneth E.; Inman, Richard D.; Matocq, Marjorie D.; Weisberg, Peter J.; Dilts, Thomas E.; Leitner, Phillip

2013-01-01

The initial habitat suitability model estimates pre‐European suitable habitat of the Mohave ground squirrel (MGS, Xerospermophilus mohavensis) covering 19,023 km2. Impact scenarios predicted that between 10 percent and 16 percent of suitable habitat has been lost to historical human disturbances, and up to an additional 10 percent may be affected by renewable energy development in the near future. These figures are the result of analyses conducted solely on public lands. State and private lands in the region also have pending proposals for renewable energy on 260 km2, and an additional 3,500 km2 may be available for renewable energy. The sum of potential habitat disturbance on public, State, and private lands could equal up to a quarter of historic suitable habitat from pre‐European settlement levels.   While the analyses conducted here consider direct impacts from the footprint of renewable energy and associated transmission corridors, there are many indirect sources of environmental disturbance related to renewable energy development (Lovich and Ennen 2011). Some of those potentially important to the MGS include: increased fugitive dust and the release of chemicals such as dust suppressants, insulating fluids, and herbicides throughout the operational life of facilities, auditory interference from the sound and vibrations of turbines, increases in predators and invasive species that further alter system processes, and changes in surface flow of water that also influence vegetation that is important in these habitats. However, there is little research in the broader context of these topics for the Mojave Desert ecosystem, and less, if any, about the MGS.  

Design of biomass management systems and components for closed loop life support systems

NASA Technical Reports Server (NTRS)

1991-01-01

The goal of the EGM 4000/1 Design class was to investigate a Biomass Management System (BMS) and design, fabricate, and test components for biomass management in a closed-loop life support system (CLLSS). The designs explored were to contribute to the development of NASA's Controlled Ecological Life Support System (CELSS) at Kennedy Space Center. Designs included a sectored plant growth unit, a container and transfer mechanism, and an air curtain system for fugitive particle control. The work performed by the class members is summarized.

Measurements of Methane Emissions and Volatile Organic Compounds from Shale Gas Operations in the Marcellus Shale

NASA Astrophysics Data System (ADS)

Omara, M.; Subramanian, R.; Sullivan, M.; Robinson, A. L.; Presto, A. A.

2014-12-01

The Marcellus Shale is the most expansive shale gas reserve in play in the United States, representing an estimated 17 to 29 % of the total domestic shale gas reserves. The rapid and extensive development of this shale gas reserve in the past decade has stimulated significant interest and debate over the climate and environmental impacts associated with fugitive releases of methane and other pollutants, including volatile organic compounds. However, the nature and magnitude of these pollutant emissions remain poorly characterized. This study utilizes the tracer release technique to characterize total fugitive methane release rates from natural gas facilities in southwestern Pennsylvania and West Virginia that are at different stages of development, including well completion flowbacks and active production. Real-time downwind concentrations of methane and two tracer gases (acetylene and nitrous oxide) released onsite at known flow rates were measured using a quantum cascade tunable infrared laser differential absorption spectrometer (QC-TILDAS, Aerodyne, Billerica, MA) and a cavity ring down spectrometer (Model G2203, Picarro, Santa Clara, CA). Evacuated Silonite canisters were used to sample ambient air during downwind transects of methane and tracer plumes to assess volatile organic compounds (VOCs). A gas chromatograph with a flame ionization detector was used to quantify VOCs following the EPA Method TO-14A. A preliminary assessment of fugitive emissions from actively producing sites indicated that methane leak rates ranged from approximately 1.8 to 6.2 SCFM, possibly reflecting differences in facility age and installed emissions control technology. A detailed comparison of methane leak rates and VOCs emissions with recent published literature for other US shale gas plays will also be discussed.

30 CFR 72.630 - Drill dust control at underground areas of underground mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... condition. Dust collectors approved under Part 33—Dust Collectors for Use in Connection with Rock Drilling...) Ventilation control. To adequately control dust from drilling rock, the air current shall be so directed that...

30 CFR 72.630 - Drill dust control at underground areas of underground mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... condition. Dust collectors approved under Part 33—Dust Collectors for Use in Connection with Rock Drilling...) Ventilation control. To adequately control dust from drilling rock, the air current shall be so directed that...

30 CFR 57.9315 - Dust control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Dust control. 57.9315 Section 57.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....9315 Dust control. Dust shall be controlled at muck piles, material transfer points, crushers, and on...

30 CFR 57.9315 - Dust control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Dust control. 57.9315 Section 57.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....9315 Dust control. Dust shall be controlled at muck piles, material transfer points, crushers, and on...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heath, Garvin; Warner, Ethan; Steinberg, Daniel

A growing number of studies have raised questions regarding uncertainties in our understanding of methane (CH 4) emissions from fugitives and venting along the natural gas (NG) supply chain. In particular, a number of measurement studies have suggested that actual levels of CH 4 emissions may be higher than estimated by EPA" tm s U.S. GHG Emission Inventory. We reviewed the literature to identify the growing number of studies that have raised questions regarding uncertainties in our understanding of methane (CH 4) emissions from fugitives and venting along the natural gas (NG) supply chain.

30 CFR 58.620 - Drill dust control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drill dust control. 58.620 Section 58.620... SAFETY AND HEALTH HEALTH STANDARDS FOR METAL AND NONMETAL MINES Miscellaneous § 58.620 Drill dust control. Holes shall be collared and drilled wet, or other effective dust control measures shall be used, when...

30 CFR 58.620 - Drill dust control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drill dust control. 58.620 Section 58.620... SAFETY AND HEALTH HEALTH STANDARDS FOR METAL AND NONMETAL MINES Miscellaneous § 58.620 Drill dust control. Holes shall be collared and drilled wet, or other effective dust control measures shall be used, when...

30 CFR 58.620 - Drill dust control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drill dust control. 58.620 Section 58.620... SAFETY AND HEALTH HEALTH STANDARDS FOR METAL AND NONMETAL MINES Miscellaneous § 58.620 Drill dust control. Holes shall be collared and drilled wet, or other effective dust control measures shall be used, when...

30 CFR 58.620 - Drill dust control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drill dust control. 58.620 Section 58.620... SAFETY AND HEALTH HEALTH STANDARDS FOR METAL AND NONMETAL MINES Miscellaneous § 58.620 Drill dust control. Holes shall be collared and drilled wet, or other effective dust control measures shall be used, when...

30 CFR 58.620 - Drill dust control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drill dust control. 58.620 Section 58.620... SAFETY AND HEALTH HEALTH STANDARDS FOR METAL AND NONMETAL MINES Miscellaneous § 58.620 Drill dust control. Holes shall be collared and drilled wet, or other effective dust control measures shall be used, when...

Impacts of air pollutants from fire and non-fire emissions on the regional air quality in Southeast Asia

NASA Astrophysics Data System (ADS)

Lee, Hsiang-He; Iraqui, Oussama; Gu, Yefu; Hung-Lam Yim, Steve; Chulakadabba, Apisada; Yiu-Ming Tonks, Adam; Yang, Zhengyu; Wang, Chien

2018-05-01

Severe haze events in Southeast Asia caused by particulate pollution have become more intense and frequent in recent years. Widespread biomass burning occurrences and particulate pollutants from human activities other than biomass burning play important roles in degrading air quality in Southeast Asia. In this study, numerical simulations have been conducted using the Weather Research and Forecasting (WRF) model coupled with a chemistry component (WRF-Chem) to quantitatively examine the contributions of aerosols emitted from fire (i.e., biomass burning) versus non-fire (including fossil fuel combustion, and road dust, etc.) sources to the degradation of air quality and visibility over Southeast Asia. These simulations cover a time period from 2002 to 2008 and are driven by emissions from (a) fossil fuel burning only, (b) biomass burning only, and (c) both fossil fuel and biomass burning. The model results reveal that 39 % of observed low-visibility days (LVDs) can be explained by either fossil fuel burning or biomass burning emissions alone, a further 20 % by fossil fuel burning alone, a further 8 % by biomass burning alone, and a further 5 % by a combination of fossil fuel burning and biomass burning. Analysis of an 24 h PM2.5 air quality index (AQI) indicates that the case with coexisting fire and non-fire PM2.5 can substantially increase the chance of AQI being in the moderate or unhealthy pollution level from 23 to 34 %. The premature mortality in major Southeast Asian cities due to degradation of air quality by particulate pollutants is estimated to increase from ˜ 4110 per year in 2002 to ˜ 6540 per year in 2008. In addition, we demonstrate the importance of certain missing non-fire anthropogenic aerosol sources including anthropogenic fugitive and industrial dusts in causing urban air quality degradation. An experiment of using machine learning algorithms to forecast the occurrence of haze events in Singapore is also explored in this study. All of these results suggest that besides minimizing biomass burning activities, an effective air pollution mitigation policy for Southeast Asia needs to consider controlling emissions from non-fire anthropogenic sources.

Evaluation of particulate matter emissions from manganese alloy production using life-cycle assessment.

PubMed

Davourie, Julia; Westfall, Luke; Ali, Mohammed; McGough, Doreen

2017-01-01

Life-cycle assessments (LCAs) provide a wealth of industry data to assist in evaluating the environmental impacts of industrial processes and product supply chains. In this investigation, data from a recent LCA covering global manganese alloy production was used to evaluate sources of particulate matter (PM) emissions associated with the manganese alloy supply chain. The analysis is aimed at providing an empirical, industry-averaged breakdown of the contribution that processes and emissions controls have on total emissions, manganese releases and occupational exposure. The assessment shows that 66% of PM emissions associated with manganese production occur beyond manganese facilities. Direct or on-site emissions represent 34% of total PM and occur predominantly as disperse sources during mineral extraction and hauling, and as primary furnace emissions. The largest contribution of manganese-bearing PM at ground-level is associated with fugitive emissions from metal and slag tapping, casting, crushing and screening. The evaluation provides a high-level ranking of emissions by process area, to assist in identifying priority areas for industry-wide initiatives to reduce emissions and occupational exposure of manganese. The range of PM emission levels in industry indicate that further enhancements in PM emissions can be achieved by sharing of best practices in emissions controls, limiting furnace conditions which lead to by-passing of emissions controls and application of secondary emission controls to capture fugitive emissions during tapping and casting. The LCA approach to evaluating PM emissions underscores the important role that process optimization and resource efficiency have on reducing PM emissions throughout the manganese supply chain. Copyright © 2016. Published by Elsevier B.V.

Methane fugitive emissions quantification using the novel 'plume camera' (spatial correlation) method

NASA Astrophysics Data System (ADS)

Crosson, E.; Rella, C.

2012-12-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Given that the global warming potential of methane is many times greater than that of carbon dioxide, the importance of quantifying methane emissions becomes clear. The rapidly increasing reliance on shale gas (or other unconventional sources) is only intensifying the interest in fugitive methane releases. Natural gas (which is predominantly methane) is an attractive energy source, as it emits 40% less carbon dioxide per Joule of energy generated than coal. However, if just a small percentage of the natural gas consumed is lost due to fugitive emissions during production, processing, or transport, this global warming benefit is lost (Howarth et al. 2012). It is therefore imperative, as production of natural gas increases, that the fugitive emissions of methane are quantified accurately. Traditional direct measurement techniques often involve physical access of the leak itself to quantify the emissions rate, and are generally require painstaking effort to first find the leak and then quantify the emissions rate. With over half a million natural gas producing wells in the U.S. (U.S. Energy Information Administration), not including the associated processing, storage, and transport facilities, and with each facility having hundreds or even thousands of fittings that can potentially leak, the need is clear to develop methodologies that can provide a rapid and accurate assessment of the total emissions rate on a per-well head basis. In this paper we present a novel method for emissions quantification which uses a 'plume camera' with three 'pixels' to quantify emissions using direct measurements of methane concentration in the downwind plume. By analyzing the spatial correlation between the pixels, the spatial extent of the instantaneous plume can be inferred. This information, when combined with the wind speed through the measurement plane, provides a direct measurement of the emission rate. One example of this method is shown in Fig. 1. This method is simple to deploy, does not require an accurate model of atmospheric transport or knowledge of the distance to the emission source or its spatial distribution. Accurate measurements of the emissions can be made with just a few minutes of data collection. Results of controlled release methane experiments are presented, and the strengths and limitations of the methodology are discussed. REFERENCES R. Howarth, R. Santoro, and A. Ingraffea (2011): "Methane and the greenhouse-gas footprint of natural gas from shale formations," Climatic Change 106, 679 - 690. Fig 1: Spatial correlation analysis for two measurement points (or pixels) distributed vertically (A and B) or horizontally (A and C), for measurements at a distance of 21 meters from a methane point source of 650 sccm. The emission rate recovered from this analysis was 496 ± 160 sccm of CH4. The total measurement time was 30 minutes.

Source influence on emission pathways and ambient PM2.5 pollution over India (2015-2050)

NASA Astrophysics Data System (ADS)

Venkataraman, Chandra; Brauer, Michael; Tibrewal, Kushal; Sadavarte, Pankaj; Ma, Qiao; Cohen, Aaron; Chaliyakunnel, Sreelekha; Frostad, Joseph; Klimont, Zbigniew; Martin, Randall V.; Millet, Dylan B.; Philip, Sajeev; Walker, Katherine; Wang, Shuxiao

2018-06-01

India is currently experiencing degraded air quality, and future economic development will lead to challenges for air quality management. Scenarios of sectoral emissions of fine particulate matter and its precursors were developed and evaluated for 2015-2050, under specific pathways of diffusion of cleaner and more energy-efficient technologies. The impacts of individual source sectors on PM2.5 concentrations were assessed through systematic simulations of spatially and temporally resolved particulate matter concentrations, using the GEOS-Chem model, followed by population-weighted aggregation to national and state levels. We find that PM2.5 pollution is a pan-India problem, with a regional character, and is not limited to urban areas or megacities. Under present-day emissions, levels in most states exceeded the national PM2.5 annual standard (40 µg m-3). Sources related to human activities were responsible for the largest proportion of the present-day population exposure to PM2.5 in India. About 60 % of India's mean population-weighted PM2.5 concentrations come from anthropogenic source sectors, while the remainder are from other sources, windblown dust and extra-regional sources. Leading contributors are residential biomass combustion, power plant and industrial coal combustion and anthropogenic dust (including coal fly ash, fugitive road dust and waste burning). Transportation, brick production and distributed diesel were other contributors to PM2.5. Future evolution of emissions under regulations set at current levels and promulgated levels caused further deterioration of air quality in 2030 and 2050. Under an ambitious prospective policy scenario, promoting very large shifts away from traditional biomass technologies and coal-based electricity generation, significant reductions in PM2.5 levels are achievable in 2030 and 2050. Effective mitigation of future air pollution in India requires adoption of aggressive prospective regulation, currently not formulated, for a three-pronged switch away from (i) biomass-fuelled traditional technologies, (ii) industrial coal-burning and (iii) open burning of agricultural residue. Future air pollution is dominated by industrial process emissions, reflecting larger expansion in industrial, rather than residential energy demand. However, even under the most active reductions envisioned, the 2050 mean exposure, excluding any impact from windblown mineral dust, is estimated to be nearly 3 times higher than the WHO Air Quality Guideline.

Experimental study on effects of drilling parameters on respirable dust production during roof bolting operations.

PubMed

Jiang, Hua; Luo, Yi; McQuerrey, Joe

2018-02-01

Underground coalmine roof bolting operators exhibit a continued risk for overexposure to airborne levels of respirable coal and crystalline silica dust from the roof drilling operation. Inhaling these dusts can cause coal worker's pneumoconiosis and silicosis. This research explores the effect of drilling control parameters, specifically drilling bite depth, on the reduction of respirable dust generated during the drilling process. Laboratory drilling experiments were conducted and results demonstrated the feasibility of this dust control approach. Both the weight and size distribution of the dust particles collected from drilling tests with different bite depths were analyzed. The results showed that the amount of total inhalable and respirable dust was inversely proportional to the drilling bite depth. Therefore, control of the drilling process to achieve proper high-bite depth for the rock can be an important approach to reducing the generation of harmful dust. Different from conventional passive engineering controls, such as mist drilling and ventilation approaches, this approach is proactive and can cut down the generation of respirable dust from the source. These findings can be used to develop an integrated drilling control algorithm to achieve the best drilling efficiency as well as reducing respirable dust and noise.

[Appropriate dust control measures for jade carving operations].

PubMed

Liu, Jiang; Wang, Qiushui; Liu, Guangquan

2002-12-01

To provide the appropriate dust control measures for jade carving operations. Dust concentrations in the workplace were measured according to GB/T 5748-85. Ventilation system of dust control were measured according to GB/T 16157-1996. Dust particle size distributions for different sources and particle size fraction collecting efficiencies of the dust collectors were measured with WY-1 in-stack 7 stage cascade impactors. On the basis of adopting wet process in the carving operations, local exhaust ventilation system for dust control was installed, which included: the special designed slot exhaust hoods with hood face velocity of 2.5 m/s and exhaust volume of 600 m3/h. The pipe sizes were determined according to the air volume passing through the pipe and the reasonable air velocities. Impinging scrubber or bag filter dust collector were selected to treat the dust laden air from the local exhaust ventilation system, which gave a total collecting efficiency of 97% for impinging scrubber and 98% for bag filter; The type of fan and its size were selected according to the total air volume of the ventilation system and maximum total pressure needed for the longest pipe line plus the pressure drop of the dust collector. Practical application showed that, after installation and use of the appropriate dust control measures, the dust concentrations in the workplaces could meet or nearly meet the national hygienic standard and the dust laden air at the local exhaust ventilation system could meet the national emission standard.

30 CFR 72.630 - Drill dust control at underground areas of underground mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drill dust control at underground areas of underground mines. 72.630 Section 72.630 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT... dust control at underground areas of underground mines. (a) Dust resulting from drilling in rock shall...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, H.R.; Overbey, W.K. Jr.; Koperna, G.J. Jr.

The purpose of this study is to assess the state-of-the-art of excavation technology as related to environmental remediation applications. A further purpose is to determine which of the excavation technologies reviewed could be used by the US Corp of Engineers in remediating contaminated soil to be excavated in the near future for construction of a new Lock and Dam at Winfield, WV. The study is designed to identify excavation methodologies and equipment which can be used at any environmental remediation site but more specifically at the Winfield site on the Kanawha River in Putnam County, West Virginia. A technical approachmore » was determined whereby a functional analysis was prepared to determine the functions to be conducted during the excavation phase of the remediation operations. A number of excavation technologies were identified from the literature. A set of screening criteria was developed that would examine the utility and ranking of the technologies with respect to the operations that needed to be conducted at the Winfield site. These criteria were performance, reliability, implementability, environmental safety, public health, and legal and regulatory compliance. The Loose Bulk excavation technology was ranked as the best technology applicable to the Winfield site. The literature was also examined to determine the success of various methods of controlling fugitive dust. Depending upon any changes in the results of chemical analyses, or prior remediation of the VOCs from the vadose zone, consideration should be given to testing a new ``Pneumatic Excavator`` which removes the VOCs liberated during the excavation process as they outgas from the soil. This equipment however would not be needed on locations with low levels of VOC emissions.« less

Natural gas fugitive emissions rates constrained by global atmospheric methane and ethane.

PubMed

Schwietzke, Stefan; Griffin, W Michael; Matthews, H Scott; Bruhwiler, Lori M P

2014-07-15

The amount of methane emissions released by the natural gas (NG) industry is a critical and uncertain value for various industry and policy decisions, such as for determining the climate implications of using NG over coal. Previous studies have estimated fugitive emissions rates (FER)--the fraction of produced NG (mainly methane and ethane) escaped to the atmosphere--between 1 and 9%. Most of these studies rely on few and outdated measurements, and some may represent only temporal/regional NG industry snapshots. This study estimates NG industry representative FER using global atmospheric methane and ethane measurements over three decades, and literature ranges of (i) tracer gas atmospheric lifetimes, (ii) non-NG source estimates, and (iii) fossil fuel fugitive gas hydrocarbon compositions. The modeling suggests an upper bound global average FER of 5% during 2006-2011, and a most likely FER of 2-4% since 2000, trending downward. These results do not account for highly uncertain natural hydrocarbon seepage, which could lower the FER. Further emissions reductions by the NG industry may be needed to ensure climate benefits over coal during the next few decades.

Effect of Simulant Type on the Absorptance and Emittance of Dusted Thermal Control Surfaces in a Simulated Lunar Environment

NASA Technical Reports Server (NTRS)

Gaier, James R.

2010-01-01

During the Apollo program the effects of lunar dust on thermal control surfaces was found to be more significant than anticipated, with several systems overheating due to deposition of dust on them. In an effort to reduce risk to future missions, a series of tests has been initiated to characterize the effects of dust on these surfaces, and then to develop technologies to mitigate that risk. Given the variations in albedo across the lunar surface, one variable that may be important is the darkness of the lunar dust, and this study was undertaken to address that concern. Three thermal control surfaces, AZ-93 white paint and AgFEP and AlFEP second surface mirrors were dusted with three different lunar dust simulants in a simulated lunar environment, and their solar absorptivity and thermal emissivity values determined experimentally. The three simulants included JSC 1AF, a darker mare simulant, NU-LHT-1D, a light highlands simulant, and 1:1 mixture of the two. The response of AZ-93 was found to be slightly more pronounced than that of AgFEP. The increased with fractional dust coverage in both types of samples by a factor of 1.7 to 3.3, depending on the type of thermal control surface and the type of dust. The of the AZ-93 decreased by about 10 percent when fully covered by dust, while that of AgFEP increased by about 10 percent. It was found that alpha/epsilon varied by more than a factor of two depending on the thermal control surface and the darkness of the dust. Given that the darkest simulant used in this study may be significantly lighter than the darkest dust that could be encountered on the lunar surface, it becomes apparent that the performance degradation of thermal control surfaces due to dust on the moon will be strongly dependent on the and of the dust in the specific locality.

Effect of Simulant Type on the Absorptance and Emittance of Dusted Thermal Control Surfaces in a Simulated Lunar Environment

NASA Technical Reports Server (NTRS)

Gaier, James R.

2010-01-01

During the Apollo program the effects of lunar dust on thermal control surfaces was found to be more significant than anticipated, with several systems overheating due to deposition of dust on them. In an effort to reduce risk to future missions, a series of tests has been initiated to characterize the effects of dust on these surfaces, and then to develop technologies to mitigate that risk. Given the variations in albedo across the lunar surface, one variable that may be important is the darkness of the lunar dust, and this study was undertaken to address that concern. Three thermal control surfaces, AZ-93 white paint and AgFEP and AlFEP second surface mirrors were dusted with three different lunar dust simulants in a simulated lunar environment, and their integrated solar absorptance ( ) and thermal emittance ( ) values determined experimentally. The three simulants included JSC-1AF, a darker mare simulant, NU-LHT-1D, a light highlands simulant, and 1:1 mixture of the two. The response of AZ-93 was found to be slightly more pronounced than that of AgFEP. The increased with fractional dust coverage in both types of samples by a factor of 1.7 to 3.3, depending on the type of thermal control surface and the type of dust. The of the AZ-93 decreased by about 10 percent when fully covered by dust, while that of AgFEP increased by about 10 percent. It was found that / varied by more than a factor of two depending on the thermal control surface and the darkness of the dust. Given that the darkest simulant used in this study may be lighter than the darkest dust that could be encountered on the lunar surface, it becomes apparent that the performance degradation of thermal control surfaces due to dust on the Moon will be strongly dependent on the and of the dust in the specific locality

Chemical signatures of urban, open burning and dust transportation in an urban environment- megacity in South Asia

NASA Astrophysics Data System (ADS)

Priyadharshini, B.; Verma, S.

2016-12-01

A sub-micron aerosol sampler (SAS) consisting of two parallel stacked filter units (SFU) was deployed at an urban location (Kolkata) to study the sub-micron aerosols (water soluble inorganic ions (WSII) and carbonaceous aerosols (elemental carbon (EC) and organic carbon (OC)) collected over a year (September 2010 to August 2011). Quantification of 10 WSII species using Ion Chromatograph (IC) indicated alkaline nature of aerosols with calcium (Ca2+) being the major neutralizing factor of acidity at the study site. In terms of WSII percentage contribution, the most abundant were crustal species (Ca2+, magnesium (Mg2+) and marine species (chloride (Cl-)), followed by the secondary species sulphate (SO42-), nitrate (NO3-) and ammonium (NH4+) . Ca2+ (fugitive and transported dust) was dominant throughout the study period with K+ concentrations exhibiting seasonality with agricultural residue burning. Further, results of carbonaceous aerosols analyzed using the OC-EC aerosol analyzer following Interagency Monitoring of Protected Visual Environment (IMPROVE) protocol exhibited pronounced seasonality in OC than EC with the overall mean concentration of OC being three folds than EC. Primary organic carbon (POC) and secondary organic carbon concentrations (SOC) estimated using EC tracer method showed 57% (43%) of POC (SOC) from various emission sources. Investigation of OC/EC ratio along with non-sea salt potassium (nss-K+) values revealed influence of season specific anthropogenic activities on both OC and EC concentrations (viz. Open burning (OB)) besides fossil fuel (FF) and biofuel (BF) usage for cooking and heating prevalent over the region. Source apportionment was discerned using positive matrix factorization (PMF) with four major factors (crustal, agricultural, anthropogenic sources and mixed source (crustal + agriculture + anthropogenic) as the primary contributors to the sub-micron aerosols at the study site.

Optical properties of size-resolved particles at a Hong Kong urban site during winter

NASA Astrophysics Data System (ADS)

Gao, Yuan; Lai, Senchao; Lee, Shun-Cheng; Yau, Pui Shan; Huang, Yu; Cheng, Yan; Wang, Tao; Xu, Zheng; Yuan, Chao; Zhang, Yingyi

2015-03-01

Visibility degradation in Hong Kong is related to the city's serious air pollution problems. To investigate the aerosols' optical properties and their relationship with the chemical composition and size distribution of the particles, a monitoring campaign was conducted at an urban site in the early winter period (from October to December, 2010). The particle light scattering coefficient (Bsp) and absorption coefficient (Bap) were measured. Two collocated Micro-Orifice Uniform Deposit Impactor samplers (MOUDI110, MSP, USA) with nominal 50% cut-off aerodynamic diameters of 18, 10, 5.6, 3.2, 1.8, 1, 0.56, 0.32, 0.18, 0.1, and 0.056 μm were used to collect size-resolved particle samples. The average Bsp and Bap were 201.96 ± 105.82 Mm- 1 and 39.91 ± 19.16 Mm- 1, with an average single scattering albedo (ωo) of 0.82 ± 0.07. The theoretical method of light extinction calculation was used to determine the extinction of the size-resolved particulate matters (PM). The reconstructed light scattering coefficient correlated well with the measured scattering value in the Hong Kong urban area. Droplet mode (0.56-1.8 μm) particles contributed most to the particle light extinction (~ 69%). Organic matter, ammonium sulphate and elemental carbon were the key components causing visibility degradation in the droplet (0.56-1.8 μm) and condensation (0.1-0.56 μm) size ranges. Five sources contributing to particle light extinction have been identified using positive matrix factorisation (PMF). Traffic/engine exhausts and secondary aerosols accounted for ~ 36% and ~ 32% of particle light extinction, respectively, followed by sea salt (15%). The remaining sources, soil/fugitive dust and tire dust, contributed by ~ 10% and 7%, respectively, to particle light extinction.

Fully-Enclosed Ceramic Micro-burners Using Fugitive Phase and Powder-based Processing

NASA Astrophysics Data System (ADS)

Do, Truong; Shin, Changseop; Kwon, Patrick; Yeom, Junghoon

2016-08-01

Ceramic-based microchemical systems (μCSs) are more suitable for operation under harsh environments such as high temperature and corrosive reactants compared to the more conventional μCS materials such as silicon and polymers. With the recent renewed interests in chemical manufacturing and process intensification, simple, inexpensive, and reliable ceramic manufacturing technologies are needed. The main objective of this paper is to introduce a new powder-based fabrication framework, which is a one-pot, cost-effective, and versatile process for ceramic μCS components. The proposed approach employs the compaction of metal-oxide sub-micron powders with a graphite fugitive phase that is burned out to create internal cavities and microchannels before full sintering. Pure alumina powder has been used without any binder phase, enabling more precise dimensional control and less structure shrinkage upon sintering. The key process steps such as powder compaction, graphite burnout during partial sintering, machining in a conventional machine tool, and final densification have been studied to characterize the process. This near-full density ceramic structure with the combustion chamber and various internal channels was fabricated to be used as a micro-burner for gas sensing applications.

Mobile sensing of point-source fugitive methane emissions using Bayesian inference: the determination of the likelihood function

NASA Astrophysics Data System (ADS)

Zhou, X.; Albertson, J. D.

2016-12-01

Natural gas is considered as a bridge fuel towards clean energy due to its potential lower greenhouse gas emission comparing with other fossil fuels. Despite numerous efforts, an efficient and cost-effective approach to monitor fugitive methane emissions along the natural gas production-supply chain has not been developed yet. Recently, mobile methane measurement has been introduced which applies a Bayesian approach to probabilistically infer methane emission rates and update estimates recursively when new measurements become available. However, the likelihood function, especially the error term which determines the shape of the estimate uncertainty, is not rigorously defined and evaluated with field data. To address this issue, we performed a series of near-source (< 30 m) controlled methane release experiments using a specialized vehicle mounted with fast response methane analyzers and a GPS unit. Methane concentrations were measured at two different heights along mobile traversals downwind of the sources, and concurrent wind and temperature data are recorded by nearby 3-D sonic anemometers. With known methane release rates, the measurements were used to determine the functional form and the parameterization of the likelihood function in the Bayesian inference scheme under different meteorological conditions.

Fully-Enclosed Ceramic Micro-burners Using Fugitive Phase and Powder-based Processing

PubMed Central

Do, Truong; Shin, Changseop; Kwon, Patrick; Yeom, Junghoon

2016-01-01

Ceramic-based microchemical systems (μCSs) are more suitable for operation under harsh environments such as high temperature and corrosive reactants compared to the more conventional μCS materials such as silicon and polymers. With the recent renewed interests in chemical manufacturing and process intensification, simple, inexpensive, and reliable ceramic manufacturing technologies are needed. The main objective of this paper is to introduce a new powder-based fabrication framework, which is a one-pot, cost-effective, and versatile process for ceramic μCS components. The proposed approach employs the compaction of metal-oxide sub-micron powders with a graphite fugitive phase that is burned out to create internal cavities and microchannels before full sintering. Pure alumina powder has been used without any binder phase, enabling more precise dimensional control and less structure shrinkage upon sintering. The key process steps such as powder compaction, graphite burnout during partial sintering, machining in a conventional machine tool, and final densification have been studied to characterize the process. This near-full density ceramic structure with the combustion chamber and various internal channels was fabricated to be used as a micro-burner for gas sensing applications. PMID:27546059

Fate and Transport of Shale-derived, Biogenic Methane.

PubMed

Hendry, M Jim; Schmeling, Erin E; Barbour, S Lee; Huang, M; Mundle, Scott O C

2017-07-07

Natural gas extraction from unconventional shale gas reservoirs is the subject of considerable public debate, with a key concern being the impact of leaking fugitive natural gases on shallow potable groundwater resources. Baseline data regarding the distribution, fate, and transport of these gases and their isotopes through natural formations prior to development are lacking. Here, we define the migration and fate of CH 4 and δ 13 C-CH 4 from an early-generation bacterial gas play in the Cretaceous of the Williston Basin, Canada to the water table. Our results show the CH 4 is generated at depth and diffuses as a conservative species through the overlying shale. We also show that the diffusive fractionation of δ 13 C-CH 4 (following glaciation) can complicate fugitive gas interpretations. The sensitivity of the δ 13 C-CH 4 profile to glacial timing suggests it may be a valuable tracer for characterizing the timing of geologic changes that control transport of CH 4 (and other solutes) and distinguishing between CH 4 that rapidly migrates upward through a well annulus or other conduit and CH 4 that diffuses upwards naturally. Results of this study were used to provide recommendations for designing baseline investigations.

Petroleum coke in the urban environment: a review of potential health effects.

PubMed

Caruso, Joseph A; Zhang, Kezhong; Schroeck, Nicholas J; McCoy, Benjamin; McElmurry, Shawn P

2015-05-29

Petroleum coke, or petcoke, is a granular coal-like industrial by-product that is separated during the refinement of heavy crude oil. Recently, the processing of material from Canadian oil sands in U.S. refineries has led to the appearance of large petcoke piles adjacent to urban communities in Detroit and Chicago. The purpose of this literature review is to assess what is known about the effects of petcoke exposure on human health. Toxicological studies in animals indicate that dermal or inhalation petcoke exposure does not lead to a significant risk for cancer development or reproductive and developmental effects. However, pulmonary inflammation was observed in long-term inhalation exposure studies. Epidemiological studies in coke oven workers have shown increased risk for cancer and chronic obstructive pulmonary diseases, but these studies are confounded by multiple industrial exposures, most notably to polycyclic aromatic hydrocarbons that are generated during petcoke production. The main threat to urban populations in the vicinity of petcoke piles is most likely fugitive dust emissions in the form of fine particulate matter. More research is required to determine whether petcoke fine particulate matter causes or exacerbates disease, either alone or in conjunction with other environmental contaminants.

Petroleum Coke in the Urban Environment: A Review of Potential Health Effects

PubMed Central

Caruso, Joseph A.; Zhang, Kezhong; Schroeck, Nicholas J.; McCoy, Benjamin; McElmurry, Shawn P.

2015-01-01

Petroleum coke, or petcoke, is a granular coal-like industrial by-product that is separated during the refinement of heavy crude oil. Recently, the processing of material from Canadian oil sands in U.S. refineries has led to the appearance of large petcoke piles adjacent to urban communities in Detroit and Chicago. The purpose of this literature review is to assess what is known about the effects of petcoke exposure on human health. Toxicological studies in animals indicate that dermal or inhalation petcoke exposure does not lead to a significant risk for cancer development or reproductive and developmental effects. However, pulmonary inflammation was observed in long-term inhalation exposure studies. Epidemiological studies in coke oven workers have shown increased risk for cancer and chronic obstructive pulmonary diseases, but these studies are confounded by multiple industrial exposures, most notably to polycyclic aromatic hydrocarbons that are generated during petcoke production. The main threat to urban populations in the vicinity of petcoke piles is most likely fugitive dust emissions in the form of fine particulate matter. More research is required to determine whether petcoke fine particulate matter causes or exacerbates disease, either alone or in conjunction with other environmental contaminants. PMID:26035666

Simulation of large particle transport near the surface under stable conditions: comparison with the Hanford tracer experiments

NASA Astrophysics Data System (ADS)

Kim, Eugene; Larson, Timothy

A plume model is presented describing the downwind transport of large particles (1-100 μm) under stable conditions. The model includes both vertical variations in wind speed and turbulence intensity as well as an algorithm for particle deposition at the surface. Model predictions compare favorably with the Hanford single and dual tracer experiments of crosswind integrated concentration (for particles: relative bias=-0.02 and 0.16, normalized mean square error=0.61 and 0.14, for the single and dual tracer experiments, respectively), whereas the US EPA's fugitive dust model consistently overestimates the observed concentrations at downwind distances beyond several hundred meters (for particles: relative bias=0.31 and 2.26, mean square error=0.42 and 1.71, respectively). For either plume model, the measured ratio of particle to gas concentration is consistently overestimated when using the deposition velocity algorithm of Sehmel and Hodgson (1978. DOE Report PNL-SA-6721, Pacific Northwest Laboratories, Richland, WA). In contrast, these same ratios are predicted with relatively little bias when using the algorithm of Kim et al. (2000. Atmospheric Environment 34 (15), 2387-2397).

Concentration variations in primary and secondary particulate matter near a major road in Korea

DOE PAGES

Ghim, Young Sung; Won, Soo Ran; Choi, Yongjoo; ...

2016-03-31

Here, particle-phase concentrations were measured at 10, 80, and 200 m from the roadside of a national highway near Seoul in January and May 2008. The highway has two lanes each way, with an average hourly traffic volume of 1,070 vehicles. In January 2008, PM 10 concentrations decreased from 10 to 80 m but increased at 200 m. Black carbon (BC) decreased only slightly with distance due to the influence of biomass burning and open burning from the surrounding areas. In May 2008, the effect of secondary formation on both PM 10 and PM 2.5 was significant due to highmore » temperatures compared with January. Because on-road emissions had little effect on secondary formation for a short time, variations in PM 10 concentrations became smaller, and PM 2.5 concentrations increased with distance. The effects of fugitive dust on PM concentrations were greater in May than in January when the mean temperature was below freezing. In the composition variations, the amounts of primary ions, organic carbon (OC), and BC were larger in January, while those of secondary ions and others were larger in PM 10, as well as PM 2.5 in May.« less

Concentration variations in primary and secondary particulate matter near a major road in Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghim, Young Sung; Won, Soo Ran; Choi, Yongjoo

Here, particle-phase concentrations were measured at 10, 80, and 200 m from the roadside of a national highway near Seoul in January and May 2008. The highway has two lanes each way, with an average hourly traffic volume of 1,070 vehicles. In January 2008, PM 10 concentrations decreased from 10 to 80 m but increased at 200 m. Black carbon (BC) decreased only slightly with distance due to the influence of biomass burning and open burning from the surrounding areas. In May 2008, the effect of secondary formation on both PM 10 and PM 2.5 was significant due to highmore » temperatures compared with January. Because on-road emissions had little effect on secondary formation for a short time, variations in PM 10 concentrations became smaller, and PM 2.5 concentrations increased with distance. The effects of fugitive dust on PM concentrations were greater in May than in January when the mean temperature was below freezing. In the composition variations, the amounts of primary ions, organic carbon (OC), and BC were larger in January, while those of secondary ions and others were larger in PM 10, as well as PM 2.5 in May.« less

Evaluation of Surface Modification as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Waters, Deborah L.; Misconin, Robert M.; Banks, Bruce A.; Crowder, Mark

2011-01-01

Three surface treatments were evaluated for their ability to lower the adhesion between lunar simulant dust and AZ93, AlFEP, and AgFEP thermal control surfaces under simulated lunar conditions. Samples were dusted in situ and exposed to a standardized puff of nitrogen gas. Thermal performance before dusting, after dusting, and after part of the dust was removed by the puff of gas, were compared to perform the assessment. None of the surface treatments was found to significantly affect the adhesion of lunar simulants to AZ93 thermal control paint. Oxygen ion beam texturing also did not lower the adhesion of lunar simulant dust to AlFEP or AgFEP. But a workfunction matching coating and a proprietary Ball Aerospace surface treatment were both found to significantly lower the adhesion of lunar simulants to AlFEP and AgFEP. Based on these results, it is recommended that all these two techniques be further explored as dust mitigation coatings for AlFEP and AgFEP thermal control surfaces.

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

30 CFR 72.620 - Drill dust control at surface mines and surface areas of underground mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... collared and drilled wet, or other effective dust control measures shall be used, when drilling non-water-soluble material. Effective dust control measures shall be used when drilling water-soluble material. ...

Nurse Case Management and Housing Interventions Reduce Allergen Exposures: The Milwaukee Randomized Controlled Trial

PubMed Central

Breysse, Jill; Wendt, Jean; Dixon, Sherry; Murphy, Amy; Wilson, Jonathan; Meurer, John; Cohn, Jennifer; Jacobs, David E.

2011-01-01

Objective We examined the impact of a combination of home environmental interventions and nurse case management services on total settled dust loadings and on allergen concentrations in the homes of asthmatic children. Methods Using a randomized longitudinal controlled trial study design, we randomly assigned homes of asthmatic children in Milwaukee to either a control (n=64) or an intervention (n=57) group. Control group homes received a visual assessment, education, bed/pillow dust mite encasings, and treatment of lead-based paint hazards. The intervention group received these same services plus nurse case management that included tailored, individual asthma action plans, provision of minor home repairs, home cleaning using special vacuuming and wet washing, and integrated pest management. Dust vacuum samples were collected from measured surface areas of floors in the TV room, kitchen, and child's bedroom at baseline and at three-, six-, and 12-month follow-up visits. Dust loading (mass per surface area) is a means of measuring total dust and the total amount of allergen present. Results For the intervention group, geometric mean dust loadings declined significantly from baseline (39 milligrams per square foot [mg/ft2]) to post-intervention (11 mg/ft2) (p<0.001). Baseline dust loading, treatment group, visit, and season were significant predictors of follow-up dust loadings. Mean post-intervention dust loadings were 72% higher in the control group. The total amount of allergen in settled house dust declined significantly following the intervention because total dust loading declined; the concentration of allergens in settled dust did not change significantly. Conclusion The combination of nurse case management and home environmental interventions promotes collaboration between health and housing professionals and is effective in reducing exposures to allergens in settled dust. PMID:21563716

Emergence, Agency, and Interaction-Notes from the Field.

PubMed

Penny, Simon

2015-01-01

This article describes the development of several interactive installations and robotic artworks developed through the 1990s and the technological, theoretical, and discursive context in which those works arose. The main works discussed are Petit Mal (1989-1995), Sympathetic Sentience (1996-1997), Fugitive I (1996-1997), Traces (1998-1999), and Fugitive II (2001-2004)-full documentation at ( www.simonpenny.net/works ). These works were motivated by a critical analysis of cognitivist computer science, which contrasted with notions of embodied experience arising from the arts. The works address questions of agency and interaction, informed by cybernetics and artificial life.

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado and Utah using mobile stable isotope (13CH4) analysis

NASA Astrophysics Data System (ADS)

Rella, Chris; Jacobson, Gloria; Crosson, Eric; Karion, Anna; Petron, Gabrielle; Sweeney, Colm

2013-04-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of CO2 emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation. However, given that the global warming potential of methane is many times greater than that of carbon dioxide (Solomon et al. 2007), the importance of quantifying the fugitive emissions of methane throughout the natural gas production and distribution process becomes clear (Howarth et al. 2011). A key step in the process of assessing the emissions arising from natural gas production activities is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis. In particular, the 13CH4 signature of natural gas (-35 to -40 permil) is significantly different that the signature of other significant sources of methane, such as landfills or ruminants (-45 to -70 permil). In this paper we present measurements of mobile field 13CH4 using a spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in two intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, and the Uintah basin in Utah. Mobile isotope measurements in the nocturnal boundary layer have been made, over a total path of 100s of km throughout the regions, allowing spatially resolved measurements of the regional isotope signature. Secondly, this analyzer was used to quantify the isotopic signature of those individual sources (natural gas fugitive emissions, concentrated animal feeding operations, and landfills) that constitute the majority of methane emissions in these regions, by making measurements of the isotope ratio directly in the downwind plume from each source. These data are combined to establish the fraction of the observed methane emissions that can be attributed to natural gas activities in the regions. The fraction of total methane emissions in the Denver-Julesburg basin that can be attributed to natural gas fugitive emissions has been determined to be 71 +/- 9%. References: 1. S. Solomon, D. Qin, M. Manning, Z. Chen, M. Marquis, K.B. Averyt, M.Tignor and H.L. Miller (eds.). IPCC, 2007: Climate Change 2007: The Physical Science Basis of the Fourth Assessment Report. Cambridge University Press, Cambridge, United Kingdom and New York, NY, USA. 2. R.W. Howarth, R. Santoro, and A. Ingraffea. "Methane and the greenhouse-gas footprint of natural gas from shale formations." Climate Change, 106, 679 (2011).

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

Estimating sources of Valley Fever pathogen propagation in southern Arizona: A remote sensing approach

NASA Astrophysics Data System (ADS)

Pianalto, Frederick S.

Coccidioidomycosis (Valley Fever) is an environmentally-mediated respiratory disease caused by the inhalation of airborne spores from the fungi Coccidioides spp. The fungi reside in arid and semi-arid soils of the Americas. The disease has increased epidemically in Arizona and other areas within the last two decades. Despite this increase, the ecology of the fungi remains obscure, and environmental antecedents of the disease are largely unstudied. Two sources of soil disturbance, hypothesized to affect soil ecology and initiate spore dissemination, are investigated. Nocturnal desert rodents interact substantially with the soil substrate. Rodents are hypothesized to act as a reservoir of coccidioidomycosis, a mediator of soil properties, and a disseminator of fungal spores. Rodent distributions are poorly mapped for the study area. We build automated multi-linear regression models and decision tree models for ten rodent species using rodent trapping data from the Organ Pipe Cactus National Monument (ORPI) in southwest Arizona with a combination of surface temperature, a vegetation index and its texture, and a suite of topographic rasters. Surface temperature, derived from Landsat TM thermal images, is the most widely selected predictive variable in both automated methods. Construction-related soil disturbance (e.g. road construction, trenching, land stripping, and earthmoving) is a significant source of fugitive dust, which decreases air quality and may carry soil pathogens. Annual differencing of Landsat Thematic Mapper (TM) mid-infrared images is used to create change images, and thresholded change areas are associated with coordinates of local dust inspections. The output metric identifies source areas of soil disturbance, and it estimates the annual amount of dust-producing surface area for eastern Pima County spanning 1994 through 2009. Spatially explicit construction-related soil disturbance and rodent abundance data are compared with coccidioidomycosis incidence data using rank order correlation and regression methods. Construction-related soil disturbance correlates strongly with annual county-wide incidence. It also correlates with Tucson periphery incidence aggregated to zip codes. Abundance values for the desert pocket mouse (Chaetodipus penicillatus), derived from a soil-adjusted vegetation index, aspect (northing) and thermal radiance, correlate with total study period incidence aggregated to zip code.

Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece.

PubMed

Argyropoulos, G; Grigoratos, Th; Voutsinas, M; Samara, C

2013-10-01

Ambient concentrations of PM10 and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM10 concentrations at the urban site (44.2 ± 33.6 μg m(-3)) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m(-3)). Source apportionment of PM10 and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM10 inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM10 contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the rural site located to the south of the power plants, although it was less important (7.2 %). Moderate contributions of fly ash were found at the urban site (5.4 and 2.7 % in the cold and the warm period, respectively). Finally, the mine field was identified as a minor PM10 source, occasionally contributing with lignite dust and/or deposited wet ash dust under dry summer conditions, with the summertime contributions ranging between 3.1 and 11.0 % among the three sites. The non-parametric bootstrapped potential source contribution function analysis was further applied to localize the regions of sources apportioned by the RCMB. For the majority of sources, source regions appeared as being located within short distances from the sampling sites (within the Peloponnesse Peninsula). More distant Greek areas of the NNE sector also appeared to be source regions for traffic emissions and secondary calcium sulfate dust.

Effects of grain dust on lungs prior to and following dust remediation.

PubMed

Pahwa, Punam; Dosman, James A; McDuffie, Helen H

2008-12-01

To determine longitudinal estimates of pulmonary function decline in Canadian grain elevator workers before and after dust control by analyzing data collected from five regions of Canada over 15 years. Declines in forced expired volume in one second and forced vital capacity before and after dust control were estimated by using a generalized estimating equations approach. For grain workers who were in the grain industry for 20 or more years both before and after dust control: the mean annual loss of forced expired volume in one second was greatest among current smoking grain workers followed by ex-smokers and nonsmokers, respectively. Similar results were obtained for forced vital capacity. Grain dust control was effective in reducing decline in the lung function measurements among grain workers in all smoking and exposure categories.

Evaluate fundamental approaches to longwall dust control. Phase III report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babbitt, C.; Bartlett, P.; Kelly, J.

1984-03-31

The overall objective of the contract is to evaluate the effectiveness of available dust control technology for double-drum shearer longwall sections in a coordinated, systematic program at a few longwall test sections and to make the results available to the entire coal mining industry. This program is investigating nine different dust control techniques. These nine subprograms encompass a broad range of dust control measures ranging from administrative controls to new hardware. They span not only presently employed methods but also those recently adopted in the United States and those proposed for the future. This report documents the Phase III effortmore » on each of the subprograms. For clarity, the report is divided in sections by subprogram as follows: Section 2, Subprogram A - passive barriers/spray air movers for dust control; Section 3, Subprogram B - practical aspects of deep cutting; Section 4, Subprogram C - stage loader dust control; Section 5, Subprogram D - longwall automation technology; Section 6, Subprogram E - longwall application of ventilation curtains; Section 7, Subprogram F - reversed drum rotation; Section 8, Subprogram G - reduction of shield generated dust; Section 9, Subprogram H - air canopies for longwalls; and Section 10, Subprogram I - mining practices. 43 figures, 11 tables.« less

Effect of ground control mesh on dust sampling and explosion mitigation.

PubMed

Alexander, D W; Chasko, L L

2015-07-01

Researchers from the National Institute for Occupational Safety and Health's Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Effect of ground control mesh on dust sampling and explosion mitigation

PubMed Central

Alexander, D.W.; Chasko, L.L.

2017-01-01

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries. PMID:28936000

Accuracy of vertical radial plume mapping technique in measuring lagoon gas emissions.

PubMed

Viguria, Maialen; Ro, Kyoung S; Stone, Kenneth C; Johnson, Melvin H

2015-04-01

Recently, the U.S. Environmental Protection Agency (EPA) posted a ground-based optical remote sensing method on its Web site called Other Test Method (OTM) 10 for measuring fugitive gas emission flux from area sources such as closed landfills. The OTM 10 utilizes the vertical radial plume mapping (VRPM) technique to calculate fugitive gas emission mass rates based on measured wind speed profiles and path-integrated gas concentrations (PICs). This study evaluates the accuracy of the VRPM technique in measuring gas emission from animal waste treatment lagoons. A field trial was designed to evaluate the accuracy of the VRPM technique. Control releases of methane (CH4) were made from a 45 m×45 m floating perforated pipe network located on an irrigation pond that resembled typical treatment lagoon environments. The accuracy of the VRPM technique was expressed by the ratio of the calculated emission rates (QVRPM) to actual emission rates (Q). Under an ideal condition of having mean wind directions mostly normal to a downwind vertical plane, the average VRPM accuracy was 0.77±0.32. However, when mean wind direction was mostly not normal to the downwind vertical plane, the emission plume was not adequately captured resulting in lower accuracies. The accuracies of these nonideal wind conditions could be significantly improved if we relaxed the VRPM wind direction criteria and combined the emission rates determined from two adjacent downwind vertical planes surrounding the lagoon. With this modification, the VRPM accuracy improved to 0.97±0.44, whereas the number of valid data sets also increased from 113 to 186. The need for developing accurate and feasible measuring techniques for fugitive gas emission from animal waste lagoons is vital for livestock gas inventories and implementation of mitigation strategies. This field lagoon gas emission study demonstrated that the EPA's vertical radial plume mapping (VRPM) technique can be used to accurately measure lagoon gas emission with two downwind vertical concentration planes surrounding the lagoon.

The Effect of Simulated Lunar Dust on the Absorptivity, Emissivity, and Operating Temperature on AZ-93 and Ag/FEP Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Siamidis, John; Panko, Scott R.; Rogers, Kerry J.; Larkin, Elizabeth M. G.

2008-01-01

JSC-1AF lunar simulant has been applied to AZ-93 and AgFEP thermal control surfaces on aluminum or composite substrates in a simulated lunar environment. The temperature of these surfaces was monitored as they were heated with a solar simulator and cooled in a 30 K coldbox. Thermal modeling was used to determine the absorptivity ( ) and emissivity ( ) of the thermal control surfaces in both their clean and dusted states. Then, a known amount of power was applied to the samples while in the coldbox and the steady state temperatures measured. It was found that even a submonolayer of simulated lunar dust can significantly degrade the performance of both white paint and second-surface mirror type thermal control surfaces under these conditions. Contrary to earlier studies, dust was found to affect as well as . Dust lowered the emissivity by as much as 16 percent in the case of AZ-93, and raised it by as much as 11 percent in the case of AgFEP. The degradation of thermal control surface by dust as measured by / rose linearly regardless of the thermal control coating or substrate, and extrapolated to degradation by a factor 3 at full coverage by dust. Submonolayer coatings of dust were found to not significantly change the steady state temperature at which a shadowed thermal control surface will radiate.

Assessing the efficacy of a novel temperature and humidity control machine to minimize house dust mite allergen exposure and clinical symptoms in allergic rhinitis children sensitized to dust mites: a pilot study.

PubMed

Manuyakorn, Wiparat; Padungpak, Savitree; Luecha, Orawin; Kamchaisatian, Wasu; Sasisakulporn, Cherapat; Vilaiyuk, Soamarat; Monyakul, Veerapol; Benjaponpitak, Suwat

2015-06-01

House dust mite avoidance is advised in dust mite sensitized patients to decrease the risk to develop allergic symptoms. Maintaining a relative humidity (RH) of less than 50% in households is recommended to prevent dust mite proliferation. To investigate the efficacy of a novel temperature and humidity machine to control the level of dust mite allergens and total nasal symptom score (TNSS) in dust mite sensitized allergic rhinitis children. Children (8-15 years) with dust mite sensitized persistent allergic rhinitis (AR) were enrolled. The temperature and humidity control machine was installed in the bedroom where the enrolled children stayed for 6 months. TNSS was assessed before and every month after machine set up and the level of dust mite allergen (Der p 1 and Der f 1) from the mattress were measured before and every 2 months after machine set up using enzyme-linked immunosorbent assay (ELISA). A total of 7 children were enrolled. Noticeable reduction of Der f 1 was observed as early as 2 months after installing the machine, but proper significant differences appeared 4 months after and remained low until the end of the experiment (p <0.05). Although no correlation was observed between TNSS and the level of dust mite allergens, there was a significant reduction in TNSS at 2 and 4 months (p <0.05) and 70% of the patients were able to stop using their intranasal corticosteroids by the end of the experiment. The level of house dust mite in mattresses was significantly reduced after using the temperature and humidity control machine. This machine may be used as an effective tool to control clinical symptoms of dust mite sensitized AR children.

Behavioral Responses of the Common Bed Bug, Cimex lectularius, to Insecticide Dusts.

PubMed

Agnew, John L; Romero, Alvaro

2017-08-08

Bed bugs have reemerged recently as a serious and growing problem not only in North America but in many parts of the world. These insects have become the most challenging pest to control in urban environments. Residual insecticides are the most common methods used for bed bug control; however, insecticide resistance limits the efficacy of treatments. Desiccant dusts have emerged as a good option to provide a better residual effect for bed bug control. Several studies have focused on determining the efficacy of dust-based insecticides against bed bugs. However, behavioral responses of bed bugs to insecticide dusts could influence their efficacy. The behavioral responses of bed bugs to six insecticide dusts commonly used in the United States were evaluated with an advanced video tracking technique (Ethovision). Bed bugs took longer to make first contact with areas treated with the diatomaceous earth (DE)-based products MotherEarth D and Alpine than pyrethroid, pyrethrins or silica gel based products, DeltaDust, Tempo 1% Dust and CimeXa, respectively. Lower visitation rates of bed bugs were recorded for areas treated with MotherEarth D, Alpine and CimeXa than that of DeltaDust, Tempo 1% Dust, and Tri-Die Silica + Pyrethrum Dust. Bed bugs spent less time in areas treated with Tri-Die Dust, CimeXa, Alpine, and MotherEarth D than DeltaDust and Tempo 1% Dust, and they exhibited a reduction in locomotor parameters when crawling on areas treated with CimeXa and Alpine. The implications of these responses to bed bug control are discussed.

Behavioral Responses of the Common Bed Bug, Cimex lectularius, to Insecticide Dusts

PubMed Central

Agnew, John L.; Romero, Alvaro

2017-01-01

Bed bugs have reemerged recently as a serious and growing problem not only in North America but in many parts of the world. These insects have become the most challenging pest to control in urban environments. Residual insecticides are the most common methods used for bed bug control; however, insecticide resistance limits the efficacy of treatments. Desiccant dusts have emerged as a good option to provide a better residual effect for bed bug control. Several studies have focused on determining the efficacy of dust-based insecticides against bed bugs. However, behavioral responses of bed bugs to insecticide dusts could influence their efficacy. The behavioral responses of bed bugs to six insecticide dusts commonly used in the United States were evaluated with an advanced video tracking technique (Ethovision). Bed bugs took longer to make first contact with areas treated with the diatomaceous earth (DE)-based products MotherEarth D and Alpine than pyrethroid, pyrethrins or silica gel based products, DeltaDust, Tempo 1% Dust and CimeXa, respectively. Lower visitation rates of bed bugs were recorded for areas treated with MotherEarth D, Alpine and CimeXa than that of DeltaDust, Tempo 1% Dust, and Tri-Die Silica + Pyrethrum Dust. Bed bugs spent less time in areas treated with Tri-Die Dust, CimeXa, Alpine, and MotherEarth D than DeltaDust and Tempo 1% Dust, and they exhibited a reduction in locomotor parameters when crawling on areas treated with CimeXa and Alpine. The implications of these responses to bed bug control are discussed. PMID:28786920

Noble gases identify the mechanisms of fugitive gas contamination in drinking-water wells overlying the Marcellus and Barnett Shales

PubMed Central

Darrah, Thomas H.; Vengosh, Avner; Jackson, Robert B.; Warner, Nathaniel R.; Poreda, Robert J.

2014-01-01

Horizontal drilling and hydraulic fracturing have enhanced energy production but raised concerns about drinking-water contamination and other environmental impacts. Identifying the sources and mechanisms of contamination can help improve the environmental and economic sustainability of shale-gas extraction. We analyzed 113 and 20 samples from drinking-water wells overlying the Marcellus and Barnett Shales, respectively, examining hydrocarbon abundance and isotopic compositions (e.g., C2H6/CH4, δ13C-CH4) and providing, to our knowledge, the first comprehensive analyses of noble gases and their isotopes (e.g., 4He, 20Ne, 36Ar) in groundwater near shale-gas wells. We addressed two questions. (i) Are elevated levels of hydrocarbon gases in drinking-water aquifers near gas wells natural or anthropogenic? (ii) If fugitive gas contamination exists, what mechanisms cause it? Against a backdrop of naturally occurring salt- and gas-rich groundwater, we identified eight discrete clusters of fugitive gas contamination, seven in Pennsylvania and one in Texas that showed increased contamination through time. Where fugitive gas contamination occurred, the relative proportions of thermogenic hydrocarbon gas (e.g., CH4, 4He) were significantly higher (P < 0.01) and the proportions of atmospheric gases (air-saturated water; e.g., N2, 36Ar) were significantly lower (P < 0.01) relative to background groundwater. Noble gas isotope and hydrocarbon data link four contamination clusters to gas leakage from intermediate-depth strata through failures of annulus cement, three to target production gases that seem to implicate faulty production casings, and one to an underground gas well failure. Noble gas data appear to rule out gas contamination by upward migration from depth through overlying geological strata triggered by horizontal drilling or hydraulic fracturing. PMID:25225410

Noble gases identify the mechanisms of fugitive gas contamination in drinking-water wells overlying the Marcellus and Barnett Shales.

PubMed

Darrah, Thomas H; Vengosh, Avner; Jackson, Robert B; Warner, Nathaniel R; Poreda, Robert J

2014-09-30

Horizontal drilling and hydraulic fracturing have enhanced energy production but raised concerns about drinking-water contamination and other environmental impacts. Identifying the sources and mechanisms of contamination can help improve the environmental and economic sustainability of shale-gas extraction. We analyzed 113 and 20 samples from drinking-water wells overlying the Marcellus and Barnett Shales, respectively, examining hydrocarbon abundance and isotopic compositions (e.g., C2H6/CH4, δ(13)C-CH4) and providing, to our knowledge, the first comprehensive analyses of noble gases and their isotopes (e.g., (4)He, (20)Ne, (36)Ar) in groundwater near shale-gas wells. We addressed two questions. (i) Are elevated levels of hydrocarbon gases in drinking-water aquifers near gas wells natural or anthropogenic? (ii) If fugitive gas contamination exists, what mechanisms cause it? Against a backdrop of naturally occurring salt- and gas-rich groundwater, we identified eight discrete clusters of fugitive gas contamination, seven in Pennsylvania and one in Texas that showed increased contamination through time. Where fugitive gas contamination occurred, the relative proportions of thermogenic hydrocarbon gas (e.g., CH4, (4)He) were significantly higher (P < 0.01) and the proportions of atmospheric gases (air-saturated water; e.g., N2, (36)Ar) were significantly lower (P < 0.01) relative to background groundwater. Noble gas isotope and hydrocarbon data link four contamination clusters to gas leakage from intermediate-depth strata through failures of annulus cement, three to target production gases that seem to implicate faulty production casings, and one to an underground gas well failure. Noble gas data appear to rule out gas contamination by upward migration from depth through overlying geological strata triggered by horizontal drilling or hydraulic fracturing.

Effective Dust Control Systems on Concrete Dowel Drilling Machinery

PubMed Central

Echt, Alan S.; Sanderson, Wayne T.; Mead, Kenneth R.; Feng, H. Amy; Farwick, Daniel R.; Farwick, Dawn Ramsey

2016-01-01

Rotary-type percussion dowel drilling machines, which drill horizontal holes in concrete pavement, have been documented to produce respirable crystalline silica concentrations above recommended exposure criteria. This places operators at potential risk for developing health effects from exposure. United States manufacturers of these machines offer optional dust control systems. The effectiveness of the dust control systems to reduce respirable dust concentrations on two types of drilling machines was evaluated under controlled conditions with the machines operating inside large tent structures in an effort to eliminate secondary exposure sources not related to the dowel-drilling operation. Area air samples were collected at breathing zone height at three locations around each machine. Through equal numbers of sampling rounds with the control systems randomly selected to be on or off, the control systems were found to significantly reduce respirable dust concentrations from a geometric mean of 54 mg per cubic meter to 3.0 mg per cubic meter on one machine and 57 mg per cubic meter to 5.3 mg per cubic meter on the other machine. This research shows that the dust control systems can dramatically reduce respirable dust concentrations by over 90% under controlled conditions. However, these systems need to be evaluated under actual work conditions to determine their effectiveness in reducing worker exposures to crystalline silica below hazardous levels. PMID:27074062

House-Dust Allergy

PubMed Central

Johnson, C. A.

1982-01-01

House-dust allergy is a common cause of perennial allergic rhinitis and extrinsic asthma. Symptoms tend to be worse when the patient is in bed. A positive skin test properly performed and interpreted confirms the diagnosis. The house-dust mite is the most important antigenic component of house-dust. Treatment consists of environmental control directed at reducing the mite content of bedroom dust, plus control of symptoms with drugs. Immunotherapy is controversial. ImagesFig. 1 PMID:21286201

A randomized trial of the effect of dust control on children's blood lead levels.

PubMed

Lanphear, B P; Winter, N L; Apetz, L; Eberly, S; Weitzman, M

1996-07-01

Dust control is recommended as one of the cornerstones of controlling childhood lead exposure; however, the effectiveness of dust control has not been demonstrated for children who have low to mild elevations in blood lead (ie, less than 25 micrograms/dL). The objective of this study was to determine whether dust control, as performed by families, had an effect on children's blood lead levels and dust lead levels in children's homes. Randomized, controlled trial. Community-based trial in Rochester, NY. One hundred four children, 12 to 31 months of age at baseline. Families and children were randomized to one of two groups. Families of children in the intervention group received cleaning supplies, information about cleaning areas that are often contaminated with lead, and a cleaning demonstration. Families in the control group received only a brochure about lead poisoning prevention. Baseline measurements of lead in blood, house dust, soil, water, and paint were taken from both groups. Seven months after enrollment, a second blood lead assay was obtained, and lead levels in household dust were measured. The main outcome measures were change in blood lead levels and dust lead levels by treatment group. The median blood lead level of children enrolled in the study was 6.7 micrograms/dL (range, 1.7 to 30.6 micrograms/dL). There was no significant difference in the change of children's blood lead levels or dust lead levels by treatment group. The median change in blood lead levels among children in the intervention group was -0.05 micrograms/dL compared with -0.60 micrograms/dL among those in the control group. There also was no significant difference in the change of dust lead by group assignment, although there was a trend toward a significant difference in the percentage of change in dust lead levels on noncarpeted floors, which was greater among houses in the intervention group. These data suggest that an intervention that consists only of providing cleaning supplies and a brief description of dust control is not effective at reducing blood lead levels among urban children with low to mild elevations in blood lead levels at a 7-month follow-up.

Implementation of the fugitive emissions system program: The OxyChem experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deshmukh, A.

An overview is provided for the Fugitive Emissions System (FES) that has been implemented at Occidental Chemical in conjunction with the computer-based maintenance system called PassPort{reg_sign} developed by Indus Corporation. The goal of PassPort{reg_sign} FES program has been to interface with facilities data, equipment information, work standards and work orders. Along the way, several implementation hurdles had to be overcome before a monitoring and regulatory system could be standardized for the appropriate maintenance, process and environmental groups. This presentation includes step-by-step account of several case studies that developed during the implementation of the FES system.

Localization and Quantification of Trace-gas Fugitive Emissions Using a Portable Optical Spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Eric; Teng, Chu; van Kessel, Theodore

We present a portable optical spectrometer for fugitive emissions monitoring of methane (CH4). The sensor operation is based on tunable diode laser absorption spectroscopy (TDLAS), using a 5 cm open path design, and targets the 2ν3 R(4) CH4 transition at 6057.1 cm-1 (1651 nm) to avoid cross-talk with common interfering atmospheric constituents. Sensitivity analysis indicates a normalized precision of 2.0 ppmv∙Hz-1/2, corresponding to a noise-equivalent absorption (NEA) of 4.4×10-6 Hz-1/2 and minimum detectible absorption (MDA) coefficient of αmin = 8.8×10-7 cm-1∙Hz-1/2. Our TDLAS sensor is deployed at the Methane Emissions Technology Evaluation Center (METEC) at Colorado State University (CSU) formore » initial demonstration of single-sensor based source localization and quantification of CH4 fugitive emissions. The TDLAS sensor is concurrently deployed with a customized chemi-resistive metal-oxide (MOX) sensor for accuracy benchmarking, demonstrating good visual correlation of the concentration time-series. Initial angle-of-arrival (AOA) results will be shown, and development towards source magnitude estimation will be described.« less

Vendors unveil one-step fugitive emissions monitoring, management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walter, M.

1995-04-01

An alliance of manufacturers has developed a ``single-source solution`` for fugitive emissions monitoring. The LeakTracker{trademark} system combines barcode scans, and vapor detection and data collection capabilities to help companies comply with leak detection and repair requirements as mandated by the Environmental Protection Agency`s Method 21 guidelines. LeakTracker doubles productivity and helps eliminate human-error factors associated with fugitive emissions monitoring. Two-person teams, clipboard-and-pencil data entry, and manual data transcription are eliminated. By automating the process and integrating all components, a technician can monitor 500 points daily following Method 21 guidelines, compared to about 250 readings per day using other systems. LeakTrackermore » includes a handheld workstation, sampling probe and laser-scan barcode reader that fit in a vest worn by a field technician. The technician points the workstation toward a barcode tag and pulls the trigger, which initiates a barcode read and automatically records the time, date and location. While the detachable probe ``sniffs`` for emissions, an analyzer interface module converts the gas detection signal from analog to digital format, allowing data to be recorded by the workstation. LeakTracker has an accuracy rate of 1 part per million.« less

Signs of Recent Volcanism and Hydrothermal Activity Along the Eastern Segment of the Galapagos Spreading Center

NASA Astrophysics Data System (ADS)

Raineault, N.; Smart, C.; Mayer, L. A.; Ballard, R. D.; Fisher, C. R.; Marsh, L.; Shank, T. M.

2016-12-01

Since the initial discovery of the Galápagos Spreading Center (GSC) vents in 1977, large-scale disturbances resulting from eruptive and tectonic activity have both destroyed and created vent habitats along the GSC. In 2015, the E/V Nautilus returned to the GSC with remotely operated vehicles (ROVs) to explore 17 kilometers of the rift valley from the Rosebud site in the west, to a previously unexplored temperature anomaly east of the Tempus Fugit vent site. In the years to over a decade since scientists last visited the Rosebud, Rose Garden, and Tempus Fugit sites, there were many changes. Most notably, the Rosebud site, where scientists found a nascent vent community and left site markers in 2002, was apparently covered with glassy basaltic sheet flows. In addition to visual exploration, oceanographic sensor measurements and direct sampling, we used the ROV Hercules imaging suite, comprised of stereo cameras and a structured light laser sensor to map an area of diffuse flow in the Tempus Fugit field (100 m x 150 m). The centimeter-level photographic and bathymetric maps created with this system, along with ROV HD video, samples, and environmental sensors, documented hydrothermal activity and changes in biological community structure (e.g., Riftia tubeworms observed in nascent stages of community development in 2011 were now, in 2015, in greater abundance (with tubes almost 4 m in length). The detection of active venting and associated faunal assemblages will provide insight into the temporal and spatial variability of venting activity at the Tempus Fugit site. On a visual survey of the Rift east of the Tempus Fugit site, extinct sulfide chimney structures were discovered and sampled. There were several chimneys and sulfide deposits in a span of over 8 km that ranged in height from over a half meter to 1.5 m tall. Diffuse flow hosting white and blue bacterial mats was observed near the chimneys complexes. The base of a large chimney structure, venting white fluids, as well as adjacent chemically-stained sediments supported vent-endemic fauna including the Pompeii worm (Alvinella pompejana) and other polychaete worms, along with pycnogonids, rat-tail fish, and galatheid crabs. This discovery provided the first evidence that the eastern segment of the GSC may have contained high-temperature, black smoker vents.

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces

PubMed Central

Beck, T.W.; Seaman, C.E.; Shahan, M.R.; Mischler, S.E.

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. PMID:29348700

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces.

PubMed

Beck, T W; Seaman, C E; Shahan, M R; Mischler, S E

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening.

Effective dust control systems on concrete dowel drilling machinery.

PubMed

Echt, Alan S; Sanderson, Wayne T; Mead, Kenneth R; Feng, H Amy; Farwick, Daniel R; Farwick, Dawn Ramsey

2016-09-01

Rotary-type percussion dowel drilling machines, which drill horizontal holes in concrete pavement, have been documented to produce respirable crystalline silica concentrations above recommended exposure criteria. This places operators at potential risk for developing health effects from exposure. United States manufacturers of these machines offer optional dust control systems. The effectiveness of the dust control systems to reduce respirable dust concentrations on two types of drilling machines was evaluated under controlled conditions with the machines operating inside large tent structures in an effort to eliminate secondary exposure sources not related to the dowel-drilling operation. Area air samples were collected at breathing zone height at three locations around each machine. Through equal numbers of sampling rounds with the control systems randomly selected to be on or off, the control systems were found to significantly reduce respirable dust concentrations from a geometric mean of 54 mg per cubic meter to 3.0 mg per cubic meter on one machine and 57 mg per cubic meter to 5.3 mg per cubic meter on the other machine. This research shows that the dust control systems can dramatically reduce respirable dust concentrations by over 90% under controlled conditions. However, these systems need to be evaluated under actual work conditions to determine their effectiveness in reducing worker exposures to crystalline silica below hazardous levels.

Source contributions to United States ozone and particulate matter over five decades from 1970 to 2020

NASA Astrophysics Data System (ADS)

Nopmongcol, Uarporn; Alvarez, Yesica; Jung, Jaegun; Grant, John; Kumar, Naresh; Yarwood, Greg

2017-10-01

Evaluating long-term air quality trends can demonstrate effectiveness of control strategies and guide future air quality management planning. Observations have shown that ozone (O3) and fine particulate matter (PM2.5) in the US have declined since as early as 1980 in some areas. But observation trends alone cannot separate effects of changes in local and global emissions to US air quality which are important to air quality planners. This study uses a regional model (CAMx) nested within a global model (GEOS-Chem) to characterize regional changes in O3 and PM2.5 due to the intercontinental transport and local/regional emissions representing six modeling years within five decades (1970-2020). We use the CAMx Source Apportionment Technology (OSAT/PSAT) to estimate contributions from 6 source sectors in 7 source regions plus 6 other groups for a total of 48 tagged contributions. On-road mobile sources consistently make the largest U.S. anthropogenic emissions contribution to O3 in all cities examined even though they decline substantially from 1970 to 2005 and also from 2005 to 2020. Off-road mobile source contributions increase from 1970 to 2005 and then decrease after 2005 in all of the cities. The boundary conditions, mostly from intercontinental transport, contribute more than 20 ppb to high maximum daily 8-h average (MDA8) O3 for all six years. We found that lowering NOx emissions raises O3 formation efficiency (OFE) across all emission categories which will limit potential O3 benefits of local NOx strategies in the near future. PM2.5 benefited from adoption of control devices between 1970 and 1980 and has continued to decline through 2005 and expected to decline further by 2020. Area sources such as residential, commercial and fugitive dust emissions stand out as making large contributions to PM2.5 that are not declining. Inter-regional transport is less important in 2020 than 1990 for both pollutants.

Coupling the Mars Dust and Water Cycles: Investigating the Role of Clouds in Controlling the Vertical Distribution of Dust During N. H. Summer

NASA Technical Reports Server (NTRS)

Kahre, M. A.; Haberle, R. M.; Hollingsworth, J. L.; Wilson, R. J.

2014-01-01

The dust cycle is critically important for the current climate of Mars. The radiative effects of dust impact the thermal and dynamical state of the atmosphere (Gierasch and Goody, 1968; Haberle et al., 1982; Zurek et al., 1992). Although dust is present in the Martian atmosphere throughout the year, the level of dustiness varies with season. The atmosphere is generally the dustiest during northern fall and winter and the least dusty during northern spring and summer (Smith, 2004). Dust particles are lifted into the atmosphere by dust storms that range in size from meters to thousands of kilometers across (Cantor et al., 2001). During some years, regional storms combine to produce hemispheric or planet encircling dust clouds that obscure the surface and raise atmospheric temperatures by as much as 40 K (Smith et al., 2002). Key recent observations of the vertical distribution of dust indicate that elevated layers of dust exist in the tropics and sub-tropics throughout much of the year (Heavens et al., 2011). These observations have brought particular focus on the processes that control the vertical distribution of dust in the Martian atmosphere. The goal of this work is to further our understanding of how clouds in particular control the vertical distribution of dust, particularly during N. H. spring and summer

30 CFR 71.301 - Respirable dust control plan; approval by District Manager and posting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... District Manager and posting. 71.301 Section 71.301 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... plan; approval by District Manager and posting. (a) The District Manager will approve respirable dust control plans on a mine-by-mine basis. When approving respirable dust control plans, the District Manager...

Impact of a lead mining-smelting complex on the forest-floor litter arthropod fauna in the new lead belt region of southeast Missouri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watson, A.P.; Van Hook, R.I.; Jackson, D.R.

1976-07-01

Studies of biological activity within the litter horizons of a watershed contaminated by emissions from a lead-ore processing complex focused on the litter-arthropod food chain as a means of detecting perturbations in a heavy-metal contaminated ecosystem. Both point sources (smelter stack emissions) and fugitive sources (ore-handling processes, yard dusts, and exposed concentrate piles) contributed to the Pb, Zn, Cu, and Cd levels in the study area. Arthropod trophic level density, biomass, and heavy metal content were determined by analysis of specimens removed from litter by von Tullgren funnel extraction, taxonomically classified, and segregated into the trophic categories. Changes in littermore » decomposition were reflected in the dynamics of the litter arthropod community. Food-chain dilution of Pb, Zn, Cu, and Cd from litter to litter consumer was occurring, as indicated by the mean concentration factors. Accumulation of Pb by litter consumers was much less than that found for the other three heavy metals. In contrast, predatory arthropods on Crooked Creek Watershed either concentrated or equilibrated with respect to Pb, Zn, and Cd from their prey, as indicated by mean total predator concentration factors. A significant depression of the Ca, Mg, and K content litter occurred relative to the control within 0.8 km of the stack. Two mechanisms were postulated to explain this result: increased leaching of cations through the litter induced by a loss of cation exchange capacity, a decrease in pH, and a decrease in microbial immobilization of macronutrients; and a decreased uptake of macronutrients due to root damage produced by heavy-metal concentrations.« less

Laboratory evaluation to reduce respirable crystalline silica dust when cutting concrete roofing tiles using a masonry saw.

PubMed

Carlo, Rebecca V; Sheehy, John; Feng, H Amy; Sieber, William K

2010-04-01

Respirable crystalline silica dust exposure in residential roofers is a recognized hazard resulting from cutting concrete roofing tiles. Roofers cutting tiles using masonry saws can be exposed to high concentrations of respirable dust. Silica exposures remain a serious threat for nearly two million U.S. construction workers. Although it is well established that respiratory diseases associated with exposure to silica dust are preventable, they continue to occur and cause disability or death. The effectiveness of both a commercially available local exhaust ventilation (LEV) system and a water suppression system in reducing silica dust was evaluated separately. The LEV system exhausted 0.24, 0.13, or 0.12 m(3)/sec of dust laden air, while the water suppression system supplied 0.13, 0.06, 0.03, or 0.02 L/sec of water to the saw blade. Using a randomized block design, implemented under laboratory conditions, the aforementioned conditions were evaluated independently on two types of concrete roofing tiles (s-shape and flat) using the same saw and blade. Each engineering control (LEV or water suppression) was replicated eight times, or four times for each type of tile. Analysis of variance was performed by comparing the mean airborne respirable dust concentrations generated during each run and engineering control treatment. The use of water controls and ventilation controls compared with the "no control" treatment resulted in a statistically significant (p < 0.05) reduction of mean respirable dust concentrations generated per tile cut. The percent reduction for respirable dust concentrations was 99% for the water control and 91% for the LEV. Results suggest that water is an effective method for reducing crystalline silica exposures. However, water damage potential, surface discolorations, cleanup, slip hazards, and other requirements may make the use of water problematic in many situations. Concerns with implementing an LEV system to control silica dust exposures include sufficient capture velocity, additional weight of the saw with the LEV system, electricity connections, and cost of air handling unit.

House dust mites, our intimate associates.

PubMed

Nadchatram, M

2005-06-01

House dust mites have lived in human contact from time immemorial. Human dander or dead skin constitutes the major organic component of the house dust ecosystem. Because the mites feed on dander, dust mites and human association will continue to co-exist as part of our environment. Efficient house-keeping practice is the best form of control to reduce infestation. However, special precautions are important when individuals are susceptible or sensitive to dust mites. House dust mites are responsible for causing asthma, rhinitis and contact dermatitis. The respiratory allergies are caused by the inhalation of dead or live mites, their faecal matter or other byproducts. Immune factors are of paramount importance in the development of dust related or mite induced respiratory diseases. House dust mites were found in some 1,000 samples of dust taken from approximately 330 dwellings in Peninsular Malaysia and Singapore. Mattresses, carpets, corners of a bedroom, and floor beneath the bed are favourable dust mite habitats. The incriminating species based on studies here and elsewhere, as well as many other species of dust mites of unknown etiological importance are widely distributed in Malaysian homes. Density of dust mites in Malaysia and Singapore is greater than in temperate countries. Prevention and control measures with reference to subjects sensitive to dust mite allergies, including chemical control described in studies conducted in Europe and America are discussed. However, a cost free and most practical way to remove mites, their faecal matter and other products is to resort to sunning the bedding and carpets to kill the living mites, and then beaten and brushed to remove the dust and other components.

Effects of dust on forest tree health in Zagros oak forests.

PubMed

Moradi, A; Taheri Abkenar, K; Afshar Mohammadian, M; Shabanian, N

2017-10-10

Dust is one of the most devastating factors for the environment threatening all animal and plant species. In many regions, the ecological and economic impact of microdust on scarce species is critical. In the western region of Iran, the Zagros forests have been exposed to dust storms for many years. In this study, the effect of dust on oak trees, the most important trees of Zagros forests, is investigated. For this purpose, 3-year-old seedlings of three species of oak trees under natural conditions were exposed to dust during spring and summer months. Seedlings were divided into two groups; one group was assigned as dust treatment and the other as control that the control group washed regularly to remove dust. Anatomical characteristics of leaves and dust deposits on leaves during the study period were examined by scanning electron microscope (SEM). The rate of photosynthesis and gas exchange in control and treated plants was examined by IRGA, LCI. SEM images showed that stomata structure, trichome density, and epicuticular waxes of leaves are different in all three species. This difference in micromorphology of species influences the effects of dust deposited on the leaves. A comparison of leaf species images in control and dust treatment showed that in dust treatment the percentage of stomata blocked by dust in three species (per unit area) of Quercus infectoria, Q. libni, and Q. brantii were 61/6, 48/4, and 38/1%, respectively. The results of leaf gas exchange investigation indicated that stomatal occlusion by dust had a negative impact on the examined parameters of three oak species (P ≤ 0.01). Thus, gas exchange and photosynthetic rates of the treated species were significantly reduced. The results of both parts of the study showed the vulnerability of the three species to dust as Q. infectoria > Q. libni > Q. brantii. Therefore, based on these findings, dust can disrupt the physiological activities of the studied species and the continuation of the exposure to dust will accelerate the process of destruction of these forests.

Influence of Air Humidity and Water Particles on Dust Control Using Ultrasonic Atomization

NASA Astrophysics Data System (ADS)

Okawa, Hirokazu; Nishi, Kentaro; Shindo, Dai; Kawamura, Youhei

2012-07-01

The influence of air humidity and water particles on dust control was examined using ultrasonic atomization at 2.4 MHz, an acrylic box (61 L), and four types of ore dust samples: green tuff (4 µm), green tuff (6 µm), kaolin, and silica. It was clearly demonstrated that ultrasonic atomization was effective in raising humidity rapidly. However, at high relative air humidity, the water particles remained stable in the box without changing to water vapor. Ultrasonic atomization was applied to suppress dust dispersion and 40-95% dust reduction was achieved at 83% relative air humidity. Dust dispersion was more effective with ultrasonic atomization than without.

Influence of continuous mining arrangements on respirable dust exposures

PubMed Central

Beck, T. W.; Organiscak, J. A.; Pollock, D. E.; Potts, J. D.; Reed, W. R.

2017-01-01

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remote-controlled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures. PMID:28529441

Evaluations of bit sleeve and twisted-body bit designs for controlling roof bolter dust

PubMed Central

Beck, T.W.

2015-01-01

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dust escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust-hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated in comparison with the dust-hog-type bit. Based on the results of our laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emission can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared with the commonly used dust-hog-type bit. PMID:26257435

Interannual Modulation of Subtropical Atlantic Boreal Summer Dust Variability by ENSO

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeFlorio, Mike; Goodwin, Ian D.; Cayan, Dan

2016-01-01

Dust variability in the climate system has been studied for several decades, yet there remains an incomplete understanding of the dynamical mechanisms controlling interannual and decadal variations in dust transport. The sparseness of multi-year observational datasets has limited our understanding of the relationship between climate variations and atmospheric dust. We use available observations and a century-length fully coupled Community Earth System Model (CESM) simulation to show that the El Niño- Southern Oscillation (ENSO) exerts a control on North African dust transport during boreal summer. In CESM, this relationship is stronger over the dusty tropical North Atlantic than near Barbados, onemore » of the few sites having a multi-decadal observed record. During strong La Niña summers in CESM, a statistically significant increase in lower tropospheric easterly wind is associated with an increase in North African dust transport over the Atlantic. Barbados dust and Pacific SST variability are only weakly correlated in both observations and CESM, suggesting that other processes are controlling the crossbasin variability of dust. We also use our CESM simulation to show that the relationship between downstream North African dust transport and ENSO fluctuates on multidecadal timescales and may be modulated by the North Atlantic Oscillation (NAO). Our findings indicate that existing observations of dust over the tropical North Atlantic are not extensive enough to completely describe the variability of dust and dust transport, and demonstrate the importance of global models to supplement and interpret observational records.« less

Fugitive Methane Gas Emission Monitoring in oil and gas industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, Levente

Identifying fugitive methane leaks allow optimization of the extraction process, can extend gas extraction equipment lifetime, and eliminate hazardous work conditions. We demonstrate a wireless sensor network based on cost effective and robust chemi-resistive methane sensors combined with real time analytics to identify leaks from 2 scfh to 10000 scfh. The chemi-resistive sensors were validated for sensitivity better than 1 ppm of methane plume detection. The real time chemical sensor and wind data is integrated into an inversion models to identify the location and the magnitude of the methane leak. This integrated solution can be deployed in outdoor environment formore » long term monitoring of chemical plumes.« less

[Analysis on occupational exposure levels and control effectiveness of dust in cement production line of new dry method].

PubMed

Wang, De-jun; Sui, Shao-feng; Kong, Fan-ling; Huang, Dong-hai

2012-11-01

To investigate the occupational exposure levels of dust in new suspension preheated dry process (NSP) cement production line and put forward rectification measures for dust-exposed posts, and to provide ideas for the modern cement production enterprises in dust control and occupational health management. Occupational health field investigation combined with field test were used to measure the time-weighted average concentration (C(TWA)) of the dust in the workplace. Rectification measures were taken for the dust-exposed posts with unqualified dust concentration, and the protective effects of dustproof facilities in the rectified workplace were evaluated. The field investigation revealed incompletely closed dustproof facilities, improperly set dust hoods, excess of dust leakage points, and other problems in the dust-exposed posts of an NSP cement production line before rectification, and the dustproof facilities could hardly exert dust removal effect. The field test showed that the vast majority of dust-exposed posts had the dust concentrations exceeding the occupational exposure limits (OELs), with a qualified rate as low as 31.8%. A series of rectification measures were taken for these posts. After the rectification, the dust-exposed posts demonstrated dramatically dropped C(TWA), and the qualified rate of dust concentration in the dust-exposed posts rose to 90.9%. The dust hazards in NSP cement production line cannot be ignored. Taking appropriate protective measures are critical for curbing dust hazards in modern cement production.

Development of the technology for the fabrication of reliable laminar from control panels

NASA Technical Reports Server (NTRS)

Meade, L. E.; Kays, A. O.; Ferrill, R. S.; Young, H. R.

1977-01-01

Materials were assessed and fabrication techniques were developed for use in the manufacture of wing surface materials compatible with the application of both aluminum alloys and nonmetallic composites. The concepts investigated included perforations and slots in the metallic test panels and microporosity and perforations in the composite test panels. Perforations were produced in the metallic test panels by the electron beam process and slots were developed by controlled gaps between the metal sheets. Microporosity was produced in the composite test panels by the resin bleed process, and perforations were produced by the fugitive fiber technique. Each of these concepts was fabricated into test panels, and air flow tests were conducted on the panels.

Wood chips for dust control on surface-mine haul roads

Treesearch

George P., Jr. Williams

1979-01-01

On a coal haul spur road where water sprinkling was the primary method of dust control, the duration of control was increased tenfold by covering the road surface with a layer of wood chips. The chip blanket prevented existing dust-size particles from being kicked up and swept into plumes by passing traffic, insulated the road surface against evaporation and protected...

Effect of Illumination Angle on the Performance of Dusted Thermal Control Surfaces in a Simulated Lunar Environment

NASA Technical Reports Server (NTRS)

Gaier, James R.

2009-01-01

JSC-1A lunar simulant has been applied to AZ93 and AgFEP thermal control surfaces on aluminum substrates in a simulated lunar environment. The temperature of these surfaces was monitored as they were heated with a solar simulator using varying angles of incidence and cooled in a 30 K coldbox. Thermal modeling was used to determine the solar absorptivity (a) and infrared emissivity (e) of the thermal control surfaces in both their clean and dusted states. It was found that even a sub-monolayer of dust can significantly raise the a of either type of surface. A full monolayer can increase the a/e ratio by a factor of 3 to 4 over a clean surface. Little angular dependence of the a of pristine thermal control surfaces for both AZ93 and AgFEP was observed, at least until 30 from the surface. The dusted surfaces showed the most angular dependence of a when the incidence angle was in the range of 25 to 35 . Samples with a full monolayer, like those with no dust, showed little angular dependence in a. The e of the dusted thermal control surfaces was within the spread of clean surfaces, with the exception of high dust coverage, where a small increase was observed at shallow angles.

Improvement of storage, handling, and transportability of fine coal. Quarterly technical progress report number 8, October 1--December 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Mulled Coal process was developed as a means of overcoming the adverse handling characteristics of wet fine coal without thermal drying. The process involves the addition of a low cost, harmless reagent to wet fine coal using off-the-shelf mixing equipment. Based on laboratory- and bench-scale testing, Mulled coal can be stored, shipped, and burned without causing any of the plugging, pasting, carryback and freezing problems normally associated with wet coal. On the other hand, Mulled Coal does not cause the fugitive and airborne dust problems normally associated with thermally dried coal. The objectives of this project are to demonstratemore » that: the Mulled Coal process, which has been proved to work on a wide range of wet fine coals at bench scale, will work equally well on a continuous basis, producing consistent quality, and at a convincing rate of production in a commercial coal preparation plant; the wet product from a fine coal cleaning circuit can be converted to a solid fuel form for ease of handling and cost savings in storage and rail car transportation; and a wet fine coal product thus converted to a solid fuel form, can be stored, shipped, and burned with conventional fuel handling, transportation, and combustion systems.« less

Gas-fired power in the UK: Bridging supply gaps and implications of domestic shale gas exploitation for UK climate change targets.

PubMed

Turk, Jeremy K; Reay, David S; Haszeldine, R Stuart

2018-03-01

There is a projected shortcoming in the fourth carbon budget of 7.5%. This shortfall may be increased if the UK pursues a domestic shale gas industry to offset projected decreases in traditional gas supply. Here we estimate that, if the project domestic gas supply gap for power generation were to be met by UK shale gas with low fugitive emissions (0.08%), an additional 20.4MtCO 2 e 1 would need to be accommodated during carbon budget periods 3-6. We find that a modest fugitive emissions rate (1%) for UK shale gas would increase global emissions compared to importing an equal quantity of Qatari liquefied natural gas. Additionally, we estimate that natural gas electricity generation would emit 420-466MtCO 2 e (460 central estimate) during the same time period within the traded EU emissions cap. We conclude that domestic shale gas production with even a modest 1% fugitive emissions rate would risk exceedance of UK carbon budgets. We also highlight that, under the current production-based greenhouse gas accounting system, the UK is incentivized to import natural gas rather than produce it domestically. Copyright © 2017 Elsevier B.V. All rights reserved.

Fugitive emissions from nanopowder manufacturing

NASA Astrophysics Data System (ADS)

Trompetter, W. J.; Ancelet, T.; Davy, P. K.; Kennedy, J.

2016-07-01

In response to health and safety questions and concerns regarding particulate matter emissions from equipment used for synthesizing NiFe and TiO2 nanopowders, a study was undertaken to assess their impact on the air quality inside and outside a laboratory where the manufacturing equipment is operated. Elemental concentrations determined by ion beam analysis (IBA) of air particulate matter (PM) samples collected hourly with a StreakerTM sampler were used to identify possible sources and estimate contributions from nanopowder production and other sources. The fugitive nanopowder emissions were the highest at the indoor sampling location when powders were being manufactured. Average fugitive emissions of 210 ng m-3 (1-h average) (maximum 2163 ng m-3 1-h average) represented 2 % (maximum 20 %) of the average PM collected (9359 ng m-3 1-h average). The measured NiFe alloy or TiO2 PM concentrations were much smaller than the 8-h time-weighted average (TWA) workplace exposure standards (WES) for these materials (≥1,000,000 ng m-3). Most PM was found to be from infiltrated outdoor ambient sources. This suggests that nanopowder production in the laboratory is not likely to have adverse health effects on individuals using the equipment, although further improvements can be made to further limit exposure.

Imaging-based dust sensors: equipment and methods

NASA Astrophysics Data System (ADS)

Bonifazi, Giuseppe; Greco, Sonia

2004-05-01

Dust detection and control in real time, represent one of the most challenging problem in all those environments where fine and ultrafine airborne particulate solids products are present. The presence of such products can be linked to several factors, often directly related and influenced by the working-production actions performed. Independently from the causes generating dust, airborne contaminants are an occupational problem of increasing interest as they are related to a wide number of diseases. In particular, airborne dusts are well known to be associated with several classical occupational lung diseases, such as the pneumoconiosis, especially at high levels of exposure. Nowadays there is also an increasing interest in other dust related diseases, from the most serious as cancer and asthma, to those related with allergies or irritation and other illnesses, also occurring at lower levels of exposure. Among the different critical factors influencing health risk for airborne dust exposure, mainly four have to be considered, that is: i) nature of the dust resulting from working in terms of presence of specific poisoning material, i.e. free silica, and morphological and morphometrical attributes of particulates constituting airborne dust; ii) size of the particles, iii) duration of exposure time and, finally, iv) airborne dust concentration in the breathing zone where the worker performs his activity. A correct dust detection is not easy, especially if some of the previous mentioned factors, have to be detected and quantified in real time in order to define specific "on-line" control actions aimed to reduce the level of the exposure to dust of the workers, as for example: i) modification of aspirating devices operating condition, change of filtering cleaning sequence, etc. . The more severe are the environmental conditions, in terms of dust presence (in quantity and quality) more difficult is to utilize efficient sampling devices. Detection devices, in fact, tend to become "blind" to dust as dust presence increases, on the other hand severe dust production conditions is exactly the case where control strategies have to be applied to realize safer conditions for the workers. In this paper the possibility to utilize a new logic to perform an "on-line" airborne dust sampling and analysis utilizing imaging is described with particular reference to dusts flowing in a duct after the caption and before their abatement by classical mechanical filtering. The study was particularly addressed to define, design and implement a logic able to extract those parameters affecting airborne dust behavior with respect to its efficient abatement. All dust sampling was performed directly in an industrial plant where tests were carried out in a controlled environment.

Global dust cycle

NASA Astrophysics Data System (ADS)

Ridgwell, Andy

Dust, micron to submicron particles and mostly comprising soil mineral fragments, affects a multitude of climatic and biogeochemical processes during its journey from its sources on land to sinks on land and in the ocean. Suspended in the atmosphere, the presence of dust can alter both shortwave and longwave radiation balances, enhance cloud nucleation, and affect photochemical reaction rates. Deposited to the land surface, dust has beneficial impacts on soil quality but detrimental implications for human health. At the interface of surface ocean and lower atmosphere, dust deposited to seawater supplies plankton with the essential micronutrient iron and hence provides an important control on marine ecosystems. This chapter reviews these various roles of dust in the Earth system; summarizes the factors controlling the production, transport, and deposition of dust; and, because the causes and consequences of dust are interlinked via climate and atmospheric CO2, discusses the potential importance of dusty feedback in past and future climate change.

Extraction of Thermal Performance Values from Samples in the Lunar Dust Adhesion Bell Jar

NASA Technical Reports Server (NTRS)

Gaier, James R.; Siamidis, John; Larkin, Elizabeth M. G.

2008-01-01

A simulation chamber has been developed to test the performance of thermal control surfaces under dusty lunar conditions. The lunar dust adhesion bell jar (LDAB) is a diffusion pumped vacuum chamber (10(exp -8) Torr) built to test material samples less than about 7 cm in diameter. The LDAB has the following lunar dust simulant processing capabilities: heating and cooling while stirring in order to degas and remove adsorbed water; RF air-plasma for activating the dust and for organic contaminant removal; RF H/He-plasma to simulate solar wind; dust sieving system for controlling particle sizes; and a controlled means of introducing the activated dust to the samples under study. The LDAB is also fitted with an in situ Xe arc lamp solar simulator, and a cold box that can reach 30 K. Samples of thermal control surfaces (2.5 cm diameter) are introduced into the chamber for calorimetric evaluation using thermocouple instrumentation. The object of this paper is to present a thermal model of the samples under test conditions and to outline the procedure to extract the absorptance, emittance, and thermal efficiency from the pristine and sub-monolayer dust covered samples.

Extraction of Thermal Performance Values from Samples in the Lunar Dust Adhesion Bell Jar

NASA Technical Reports Server (NTRS)

Gaier, James R.; Siamidis, John; Larkin, Elizabeth M.G.

2008-01-01

A simulation chamber has been developed to test the performance of thermal control surfaces under dusty lunar conditions. The lunar dust adhesion bell jar (LDAB) is a diffusion pumped vacuum chamber (10-8 Torr) built to test material samples less than about 7 cm in diameter. The LDAB has the following lunar dust stimulant processing capabilities: heating and cooling while stirring in order to degas and remove absorbed water; RF air-plasma for activating the dust and for organic contaminant removal; RF H/He-plasma to simulate solar wind; dust sieving system for controlling particle sizes; and a controlled means of introducing the activated dust to the samples under study. The LDAB is also fitted with an in situ Xe arc lamp solar simulator, and a cold box that can reach 30 K. Samples of thermal control surfaces (2.5 cm diameter) are introduced into the chamber for calorimetric evaluation using thermocouple instrumentation. The object of this paper is to present a thermal model of the samples under test conditions, and to outline the procedure to extract the absorptance, emittance, and thermal efficiency from the pristine and sub-monolayer dust covered samples

Extraction of Thermal Performance Values from Samples in the Lunar Dust Adhesion Bell Jar

NASA Technical Reports Server (NTRS)

Gaier, James R.; Siamidis, John; Larkin, Elizabeth M. G.

2010-01-01

A simulation chamber has been developed to test the performance of thermal control surfaces under dusty lunar conditions. The lunar dust adhesion bell jar (LDAB) is a diffusion pumped vacuum chamber (10(exp -8) Torr) built to test material samples less than about 7 cm in diameter. The LDAB has the following lunar dust simulant processing capabilities: heating and cooling while stirring in order to degas and remove adsorbed water; RF air-plasma for activating the dust and for organic contaminant removal; RF H/He-plasma to simulate solar wind; dust sieving system for controlling particle sizes; and a controlled means of introducing the activated dust to the samples under study. The LDAB is also fitted with an in situ Xe arc lamp solar simulator, and a cold box that can reach 30 K. Samples of thermal control surfaces (2.5 cm diameter) are introduced into the chamber for calorimetric evaluation using thermocouple instrumentation. The object of this paper is to present a thermal model of the samples under test conditions and to outline the procedure to extract the absorptance, emittance, and thermal efficiency from the pristine and sub-monolayer dust covered samples.

The winter gap effect in methane leak detection and repair with optical gas imaging cameras

NASA Astrophysics Data System (ADS)

Fox, T. A.; Barchyn, T.; Hugenholtz, C.

2017-12-01

Implementing effective leak detection and repair (LDAR) programs is essential for mitigating fugitive methane emissions from oil and gas operations. In Canada, newly proposed regulations will require that high-risk facilities be surveyed 3 times/yr for fugitive leaks. Like the United States, Canada promotes the use of Optical Gas Imaging cameras (OGIs) for detecting natural gas leaks during LDAR surveys. However, recent research suggests OGIs may perform poorly under adverse environmental conditions, especially in low temperatures. For regions like Canada that experience cold winters, OGIs may not be reliably used for months at a time, meaning that leaks may accumulate and emit for longer periods before being repaired. While considerable oil and gas activity occurs in high-latitude regions with cold winters, no research has explored how extended cold periods impact OGI-focused LDAR programs. To improve this understanding, we present a simple model exploring relationships among winter gap length, fugitive methane emissions, and investment input for LDAR programs employing OGI instruments in gas producing regions of different latitudes. Preliminary results suggest that longer gaps between LDAR surveys caused by cold temperatures result in either 1) higher total emissions for the year, or 2) greater time and equipment investment in LDAR programs to achieve emissions mitigation equivalent to LDAR programs operating under ideal conditions. When weather constraints are removed and LDAR surveys are evenly spaced throughout the year, emissions mitigation is optimized. However, as the winter gap duration and the size of the implicated area increases, fugitive leaks last longer. Furthermore, a spillover effect is observed as LDAR crews become overwhelmed with the high volume of work required as temperatures increase in the spring. Our model adds weight to the argument that LDAR programs should be tailored to regional needs, and that regulators should be more cognisant of sensor-specific limitations as they develop LDAR protocols.

Instruments speak global language

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nudo, L.

1993-07-01

If all goes as planned, companies that use instruments for measurement and control will get more complete, reliable and repeatable information about their processes with advanced digital devices that speak a global language. That language, in technical terms, is known as international fieldbus. But it's not much different from English's role as the international language of business. Companies that use a remote measurement device for environmental applications, such as pH control and fugitive emissions control, are candidates for fieldbus devices, which are much faster and measure more process variables than their counterpart analog devices. With the advent of a globalmore » fieldbus, users will see digital valves, solenoids and multivariable transmitters. Fieldbus technology redefines the roles of the control system and field devices. The control system still serves as a central clearinghouse, but field devices will handle more control and reporting functions and generate data that can be used for trending and preventive maintenance.« less

Effect of soil texture and chemical properties on laboratory-generated dust emissions from SW North America

NASA Astrophysics Data System (ADS)

Mockford, T.; Zobeck, T. M.; Lee, J. A.; Gill, T. E.; Dominguez, M. A.; Peinado, P.

2012-12-01

Understanding the controls of mineral dust emissions and their particle size distributions during wind-erosion events is critical as dust particles play a significant impact in shaping the earth's climate. It has been suggested that emission rates and particle size distributions are independent of soil chemistry and soil texture. In this study, 45 samples of wind-erodible surface soils from the Southern High Plains and Chihuahuan Desert regions of Texas, New Mexico, Colorado and Chihuahua were analyzed by the Lubbock Dust Generation, Analysis and Sampling System (LDGASS) and a Beckman-Coulter particle multisizer. The LDGASS created dust emissions in a controlled laboratory setting using a rotating arm which allows particle collisions. The emitted dust was transferred to a chamber where particulate matter concentration was recorded using a DataRam and MiniVol filter and dust particle size distribution was recorded using a GRIMM particle analyzer. Particle size analysis was also determined from samples deposited on the Mini-Vol filters using a Beckman-Coulter particle multisizer. Soil textures of source samples ranged from sands and sandy loams to clays and silts. Initial results suggest that total dust emissions increased with increasing soil clay and silt content and decreased with increasing sand content. Particle size distribution analysis showed a similar relationship; soils with high silt content produced the widest range of dust particle sizes and the smallest dust particles. Sand grains seem to produce the largest dust particles. Chemical control of dust emissions by calcium carbonate content will also be discussed.

Field Observations of Methane Emissions from Unconventional and Conventional Fossil Fuel Exploration

NASA Astrophysics Data System (ADS)

Dubey, M.; Lindenmaier, R.; Arata, C.; Costigan, K. R.; Frankenberg, C.; Kort, E. A.; Rahn, T. A.; Henderson, B. G.; Love, S. P.; Aubrey, A. D.

2013-12-01

Energy from methane (CH4) has lower carbon dioxide and air pollutant emissions per unit energy produced than coal or oil making it a desirable fossil fuel. Hydraulic fracturing is allowing United States to harvest the nation's abundant domestic shale gas reservoirs to achieve energy independence. However, CH4 is a gas that is hard to contain during mining, processing, transport and end-use. Therefore fugitive CH4 leaks occur that are reported in bottom up inventories by the EPA. Recent targeted field observations at selected plays have provided top down CH4 leak estimates that are larger than the reported EPA inventories. Furthermore, no long-term regional baselines are available to delineate leaks from unconventional mining operations from historical conventional mining. We will report and compare observations of fugitive CH4 leaks from conventional and unconventional mining to understand changes from technology shifts. We will report in situ and regional column measurements of CH4, its isotopologue 13CH4 and ethane (C2H6) at our Four Corners site near Farmington, NM. The region has substantial coal bed methane, conventional oil and gas production, processing and distribution with minimal hydraulic fracturing activity. We observe large enhancements in in situ and regional column CH4 with distinct time dependence. Our in situ 13CH4 observations and remote C2H6/CH4 provide strong evidence of thermogenic sources. Comparisons of WRF-simulations with emissions inventory (Edgar) with our observations show that the fugitive CH4 leaks from conventional mining are 3 times greater than reported. We also compare in situ mobile surveys of fugitive CH4 and 13CH4 leak signals in basins with conventional (San Juan) mining and unconventional (Permian and Powder River) mining. A large number of active and closed wells were sampled in these regions. Furthermore, play scale surveys on public roads allowed us to gain a regional perspective. The composition of atmospheric 13CH4 observed in the Powder River basin was lighter than the Permian and San Juan basins indicating a higher microbial generated fraction. More extensive and larger CH4 enhancements were measured in the Permian basin that could be a result of the large expansion of unconventional oil and gas production in this region. However, there are variations amongst wells and plays suggesting that operator practices and reservoir formation play a role in determining the fugitive leaks.

The impacts of the axial-to-radial airflow quantity ratio and suction distance on air curtain dust control in a fully mechanized coal face.

PubMed

Wang, Hao; Cheng, Weimin; Sun, Biao; Yu, Haiming; Jin, Hu

2018-03-01

To understand the impacts of the axial-to-radial airflow quantity ratio (denoted as R) and the suction distance (denoted as D s ) on air curtain dust control in a fully mechanized coal face, the 3 down 610 coal face in Jiangzhuang coal mine was numerically simulated in this study. A mathematic model was established to describe the airflow migration and dust diffusion in a coal face, and a scaled physical model was constructed. The comparison between simulation results and field measurements validated the model and the parameter settings. Furthermore, the airflow migration and dust diffusion at various R and D s are analyzed using Ansys CFD. The results show that a reduction of R and D s is conducive to the formation of an effective axial dust control air curtain; the dust diffusion distance decreases with the decrease of both R and D s . By analyzing the simulation results, the optimal parameter for air curtain dust control in the 3 down 610 coal face and those faces with similar production conditions is determined as R = 1/9 and D s  = 2 m. Under the optimal parameter condition, the high-concentration dust can be confined in front of the mining driver within a space 5.8 m away from the coal face.

Foam property tests to evaluate the potential for longwall shield dust control.

PubMed

Reed, W R; Beck, T W; Zheng, Y; Klima, S; Driscoll, J

2018-01-01

Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration's lower coal mine respirable dust standard of 1.5 mg/m 3 . Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control.

Foam property tests to evaluate the potential for longwall shield dust control

PubMed Central

Reed, W.R.; Beck, T.W.; Zheng, Y.; Klima, S.; Driscoll, J.

2018-01-01

Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. PMID:29416179

Elements in Mud and Snow in the Vicinity of the DeLong Mountain Regional Transportation System Road, Red Dog Mine, and Cape Krusenstern National Monument, Alaska, 2005-06

USGS Publications Warehouse

Brumbaugh, William J.; May, Thomas W.

2008-01-01

A small number of mud, road bed soil, and snow samples were collected in 2005 and 2006 to assess metal concentrations and loadings to areas adjacent to the DeLong Mountain Regional Transportation System (DMTS) road in northwest Alaska. The DMTS road is used by large trucks to transport lead and zinc concentrates from Red Dog Mine to the shipping facility at Red Dog Port; it traverses 32 kilometers of land in Cape Krusenstern National Monument (CAKR). Mud collected in the summer of 2005 from wheel-wells of two passenger vehicles used for transport between Red Dog Mine and the port facility were enriched in cadmium, lead, and zinc by factors of about 200 to 800 as compared with mud collected from a vehicle stationed in Kotzebue, Alaska, whereas DMTS road bed soil samples were enriched by factors of 6 to 12. Thus, as of 2005, dispersal of mine ore wastes or concentrates by vehicles appeared to remain a potential source of metals along the DMTS road. Compared to snow samples obtained near a gravel road located near Kotzebue, Alaska, metal loadings estimated from individual snow samples collected in CAKR in April 2006 near three creeks, 13 to 50 meters from the road, were greater by factors of 13 to 316 for cadmium, 28 to 589 for lead, and 8 to 195 for zinc. When averaged for all three creek locations, mean loadings of cadmium, lead, and zinc calculated from snow samples collected at a nominal distance of 15 meters to the north of the road were 0.63, 34, and 89 milligrams of metal per square meter, respectively. Variability of particulate and metal loadings between individual samples and the three creek locations probably was affected by localized meteorological conditions and micro-topography on the snow drift and scour patterns, but road orientation on attainable truck speeds also might have been a factor. Results indicated that the ?port effect?, previously attributed to fugitive metal-enriched dusts stemming from concentrate transfer operations at the port facility, was not necessarily an important factor affecting spatial differences of metals deposition in snow along the road in CAKR during winter 2005?06. The average metal content of particulates in 2005?06 snow samples was slightly less than that of snow samples collected by the U.S. Geological Survey in CAKR at three near-road locations in April 2003. Mean metals concentrations in 2006 snow particulates were about three times greater than in the road bed soils that were sampled in 2005; however, the fraction of annual metals loadings occurring in winter as compared to the remainder of the year was not readily determined by these data. Although procedures have been implemented in recent years to reduce the quantities of metal-enriched fugitive dusts, particulates dispersed near the road during the winter of 2005?06 were enriched in metals and these particulates contributed considerable metal loadings to the nearby terrain.

Effect of ecological restoration programs on dust concentrations in the North China Plain: a case study

NASA Astrophysics Data System (ADS)

Long, Xin; Tie, Xuexi; Li, Guohui; Cao, Junji; Feng, Tian; Zhao, Shuyu; Xing, Li; An, Zhisheng

2018-05-01

In recent decades, the Chinese government has made a great effort in initiating large-scale ecological restoration programs (ERPs) to reduce the dust concentrations in China, especially for dust storm episodes. Using the Moderate Resolution Imaging Spectroradiometer (MODIS) land cover product, the ERP-induced land cover changes are quantitatively evaluated in this study. Two obvious vegetation protective barriers arise throughout China from the southwest to the northeast, which are well known as the Green Great Wall (GGW). Both the grass GGW and forest GGW are located between the dust source region (DSR) and the densely populated North China Plain (NCP). To assess the effect of ERPs on dust concentrations, a regional transport/dust model (WRF-DUST, Weather Research and Forecast model with dust) is applied to investigate the evolution of dust plumes during a strong dust storm episode from 2 to 8 March 2016. The WRF-DUST model generally performs reasonably well in reproducing the temporal variations and spatial distributions of near-surface [PMC] (mass concentration of particulate matter with aerodynamic diameter between 2.5 and 10 µm) during the dust storm event. Sensitivity experiments have indicated that the ERP-induced GGWs help to reduce the dust concentration in the NCP, especially in BTH (Beijing, Tianjin, and Hebei). When the dust storm is transported from the upwind DSR to the downwind NCP, the [PMC] reduction ranges from -5 to -15 % in the NCP, with a maximum reduction of -12.4 % (-19.2 µg m-3) in BTH and -7.6 % (-10.1 µg m-3) in the NCP. We find the dust plumes move up to the upper atmosphere and are transported from the upwind DSR to the downwind NCP, accompanied by dust decrease. During the episode, the forest GGW is nonsignificant in dust concentration control because it is of benefit for dry deposition and not for emission. Conversely, the grass GGW is beneficial in controlling dust erosion and is the dominant reason for [PMC] decrease in the NCP. Because the air pollution is severe in eastern China, especially in the NCP, and the contribution of dust episodes is significant, the reduction of dust concentrations will have important effects on severe air pollution. This study illustrates the considerable contribution of ERPs to the control of air pollution in China, especially in springtime.

Graphic products used in the evaluation of traditional and emerging remote sensing technologies for the detection of fugitive contamination at selected superfund hazardous waste sites

USGS Publications Warehouse

Slonecker, E. Terrence; Fisher, Gary B.

2011-01-01

This report presents the overhead imagery and field sampling results used to prepare U.S. Geological Survey Open-File Report 2011-1050, 'Evaluation of Traditional and Emerging Remote Sensing Technologies for the Detection of Fugitive Contamination at Selected Superfund Hazardous Waste Sites'. These graphic products were used in the evaluation of remote sensing technology in postclosure monitoring of hazardous waste sites and represent an ongoing research effort. Soil sampling results presented here were accomplished with field portable x-ray fluoresence (XRF) technology and are used as screening tools only representing the current conditions of metals and other contaminants at selected Superfund hazardous waste sites.

Is Optical Gas Imaging Effective for Detecting Fugitive Methane Emissions? - A Technological and Policy Perspective

NASA Astrophysics Data System (ADS)

Ravikumar, A. P.; Wang, J.; Brandt, A. R.

2016-12-01

Mitigating fugitive methane emissions from the oil and gas industry has become an important concern for both businesses and regulators. While recent studies have improved our understanding of emissions from all sectors of the natural gas supply chain, cost-effectively identifying leaks over expansive natural gas infrastructure remains a significant challenge. Recently, the Environmental Protection Agency (EPA) has recommended the use of optical gas imaging (OGI) technologies to be used in industry-wide leak detection and repair (LDAR) programs. However, there has been little to no systematic study of the effectiveness of infrared-camera-based OGI technology for leak detection applications. Here, we develop a physics-based model that simulates a passive infrared camera imaging a methane leak against varying background and ambient conditions. We verify the simulation tool through a series of large-volume controlled release field experiments wherein known quantities of methane were released and imaged from a range of distances. After simulator verification, we analyze the effects of environmental conditions like temperature, wind, and imaging background on the amount of methane detected from a statistically representative survey program. We also examine the effects of LDAR design parameters like imaging distance, leak size distribution, and gas composition. We show that imaging distance strongly affects leak detection - EPA's expectation of a 60% reduction in fugitive emissions based on a semi-annual LDAR survey will be realized only if leaks are imaged at a distance less than 10 m from the source under ideal environmental conditions. Local wind speed is also shown to be important. We show that minimum detection limits are 3 to 4 times higher for wet-gas compositions that contain a significant fraction of ethane and propane, resulting a significantly large leakage rate. We also explore the importance of `super-emitters' on the performance of an OGI-based leak detection program, and show that OGI technology can be used as an approximate leak-quantification method to selectively target the biggest leaks. Finally, we also provide recommendations and best-practices guidelines for achieving expected methane mitigation.

Molten Metal Treatment by Salt Fluxing with Low Environmental Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yogeshwar Sahai

2007-07-31

Abstract: Chlorine gas is traditionally used for fluxing of aluminum melt for removal of alkali and alkaline earth elements. However this results in undesirable emissions of particulate matter and gases such as HCl and chlorine, which are often at unacceptable levels. Additionally, chlorine gas is highly toxic and its handling, storage, and use pose risks to employees and the local community. Holding of even minimal amounts of chlorine necessitates extensive training for all plant employees. Fugitive emissions from chlorine usage within the plant cause accelerated corrosion of plant equipment. The Secondary Aluminum Maximum Achievable Control Technology (MACT) under the Cleanmore » Air Act, finalized in March 2000 has set very tough new limits on particulate matter (PM) and total hydrogen chloride emissions from aluminum melting and holding furnaces. These limits are 0.4 and 0.1 lbs per ton of aluminum for hydrogen chloride and particulate emissions, respectively. Assuming new technologies for meeting these limits can be found, additional requirements under the Clean Air Act (Prevention of Significant Deterioration and New Source Review) trigger Best Available Control Technology (BACT) for new sources with annual emissions (net emissions not expressed per ton of production) over specified amounts. BACT currently is lime coated bag-houses for control of particulate and HCl emissions. These controls are expensive, difficult to operate and maintain, and result in reduced American competitiveness in the global economy. Solid salt fluxing is emerging as a viable option for the replacement of chlorine gas fluxing, provided emissions can be consistently maintained below the required levels. This project was a cooperative effort between the Ohio State University and Alcoa to investigate and optimize the effects of solid chloride flux addition in molten metal for alkali impurity and non-metallic inclusion removal minimizing dust and toxic emissions and maximizing energy conservation. In this program, the salt metal interactions were studies and the emissions at laboratory scale at OSU were monitored. The goal of the project was to obtain a fundamental understanding, based on first principles, of the pollutant formation that occurs when the salts are used in furnaces. This information will be used to control process parameters so that emissions are consistently below the required levels. The information obtained in these experiments will be used in industrial furnaces at aluminum plants and which will help in optimizing the process.« less

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport.

PubMed

Shahan, M R; Seaman, C E; Beck, T W; Colinet, J F; Mischler, S E

2017-09-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8.

House dust mite barrier bedding for childhood asthma: randomised placebo controlled trial in primary care [ISRCTN63308372].

PubMed

Sheikh, Aziz; Hurwitz, Brian; Sibbald, Bonnie; Barnes, Greta; Howe, Maggie; Durham, Stephen

2002-06-18

The house dust mite is the most important environmental allergen implicated in the aetiology of childhood asthma in the UK. Dust mite barrier bedding is relatively inexpensive, convenient to use, and of proven effectiveness in reducing mattress house dust mite load, but no studies have evaluated its clinical effectiveness in the control of childhood asthma when dispensed in primary care. We therefore aimed to evaluate the effectiveness of house dust mite barrier bedding in children with asthma treated in primary care. Pragmatic, randomised, double-blind, placebo controlled trial conducted in eight family practices in England. Forty-seven children aged 5 to 14 years with confirmed house dust mite sensitive asthma were randomised to receive six months treatment with either house dust mite barrier or placebo bedding. Peak expiratory flow was the main outcome measure of interest; secondary outcome measures included asthma symptom scores and asthma medication usage. No difference was noted in mean monthly peak expiratory flow, asthma symptom score, medication usage or asthma consultations, between children who received active bedding and those who received placebo bedding. Treating house dust mite sensitive asthmatic children in primary care with house dust mite barrier bedding for six months failed to improve peak expiratory flow. Results strongly suggest that the intervention made no impact upon other clinical features of asthma.

House dust mite barrier bedding for childhood asthma: randomised placebo controlled trial in primary care [ISRCTN63308372

PubMed Central

Sheikh, Aziz; Hurwitz, Brian; Sibbald, Bonnie; Barnes, Greta; Howe, Maggie; Durham, Stephen

2002-01-01

Background The house dust mite is the most important environmental allergen implicated in the aetiology of childhood asthma in the UK. Dust mite barrier bedding is relatively inexpensive, convenient to use, and of proven effectiveness in reducing mattress house dust mite load, but no studies have evaluated its clinical effectiveness in the control of childhood asthma when dispensed in primary care. We therefore aimed to evaluate the effectiveness of house dust mite barrier bedding in children with asthma treated in primary care. Methods Pragmatic, randomised, double-blind, placebo controlled trial conducted in eight family practices in England. Forty-seven children aged 5 to 14 years with confirmed house dust mite sensitive asthma were randomised to receive six months treatment with either house dust mite barrier or placebo bedding. Peak expiratory flow was the main outcome measure of interest; secondary outcome measures included asthma symptom scores and asthma medication usage. Results No difference was noted in mean monthly peak expiratory flow, asthma symptom score, medication usage or asthma consultations, between children who received active bedding and those who received placebo bedding. Conclusions Treating house dust mite sensitive asthmatic children in primary care with house dust mite barrier bedding for six months failed to improve peak expiratory flow. Results strongly suggest that the intervention made no impact upon other clinical features of asthma. PMID:12079502

SPARCLE: Electrostatic Dust Control Tool Proof of Concept

NASA Technical Reports Server (NTRS)

Clark, P. E.; Curtis, S. A.; Minetto, F.; Marshall, J.; Nuth, J.; Calle, C.

2010-01-01

Successful exploration of most planetary surfaces, with their impact-generated dusty regoliths, will depend on the capabilities to keep surfaces free of the performance-compromising dust. Once in contact with surfaces, whether set in motion by natural or mechanical means, regolith fines, or dust, behave like abrasive Velcro, coating surfaces, clogging mechanisms, making movement progressively more difticult, and being almost impossible to remove by mechanical mcans (brushing). The successful dust removal strategy will deal with dust dynamics resulting from interaction between Van der Waals and Coulombic forces. Here, proof of concept for an electrostatically-based concept for dust control tool is described and demonstrated. A low power focused electron beam is used in the presence of a small electrical field to increase the negative charge to mass ratio of a dusty surface until dust repulsion and attraction to a lower potential surface, acting as a dust collector, occurred. Our goal is a compact device of less than 5 kg mass and using less than 5 watts of power to be operational in less than 5 years with heritage from ionic sweepers for active spacecraft potential control (e.g ., on POLAR). Rovers could be fitted with devices that could hamess the removal of dust for sampling as part of the extended exploration process on Mercury, Mars, asteroids or outer solar system satellites, as well as the Moon.

Development of differential absorption lidar (DIAL) for detection of CO2, CH4 and PM in Alberta

NASA Astrophysics Data System (ADS)

Wojcik, Michael; Crowther, Blake; Lemon, Robert; Valupadas, Prasad; Fu, Long; Leung, Bonnie; Yang, Zheng; Huda, Quamrul; Chambers, Allan

2005-05-01

Rapid expansion of the oil and gas industry in Alberta, including the oil sands, has challenged the Alberta Government to keep pace in its efforts to monitor and mitigate the environmental impacts of development. The limitations of current monitoring systems has pushed the provincial government to seek out advanced sensing technologies such as satellite imagery and laser based sensors. The Space Dynamics Laboratory (SDL) of Utah State University, in cooperation with Alberta Environmental Monitoring, Evaluation and Reporting Agency (AEMERA), has developed North America's first mobile differential absorption lidar (DIAL) system designed specifically for emissions measurement. This instrument is housed inside a 36' trailer which allows for mobility to travel across Alberta to characterize source emissions and to locate fugitive leaks. DIAL is capable of measuring concentrations for carbon dioxide (CO2) and methane (CH4) at ranges of up to 3 km with a spatial resolution of 10 meters. DIAL can map both CO2 and CH4, as well as particulate matter (PM) in a linear fashion; by scanning the laser beam in both azimuth and elevation DIAL can create images of emissions in two dimensions. DIAL imagery may be used to understand and control production practices, characterize source emissions, determine emission factors, locate fugitive leaks, assess plume dispersion, and confirm air dispersion modeling. A system overview of the DIAL instrument and some representative results will be discussed.

Real-time measurement of dust in the workplace using video exposure monitoring: Farming to pharmaceuticals

NASA Astrophysics Data System (ADS)

Walsh, P. T.; Forth, A. R.; Clark, R. D. R.; Dowker, K. P.; Thorpe, A.

2009-02-01

Real-time, photometric, portable dust monitors have been employed for video exposure monitoring (VEM) to measure and highlight dust levels generated by work activities, illustrate dust control techniques, and demonstrate good practice. Two workplaces, presenting different challenges for measurement, were used to illustrate the capabilities of VEM: (a) poultry farming activities and (b) powder transfer operations in a pharmaceutical company. For the poultry farm work, the real-time monitors were calibrated with respect to the respirable and inhalable dust concentrations using cyclone and IOM reference samplers respectively. Different rankings of exposure for typical activities were found on the small farm studied here compared to previous exposure measurements at larger poultry farms: these were mainly attributed to the different scales of operation. Large variations in the ratios of respirable, inhalable and real-time monitor TWA concentrations of poultry farm dust for various activities were found. This has implications for the calibration of light-scattering dust monitors with respect to inhalable dust concentration. In the pharmaceutical application, the effectiveness of a curtain barrier for dust control when dispensing powder in a downflow booth was rapidly demonstrated.

Reducing float coal dust

PubMed Central

Patts, J.R.; Colinet, J.F.; Janisko, S.J.; Barone, T.L.; Patts, L.D.

2016-01-01

Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. PMID:28018004

Life cycle and reproduction of house-dust mites: environmental factors influencing mite populations.

PubMed

Hart, B J

1998-01-01

An understanding of the life cycle of house-dust mites, as well as environmental factors influencing mite populations, can be exploited in mite control. The most important limiting factor for house-dust-mite populations is air humidity. House-dust mites osmoregulate through the cuticle and therefore require a high ambient air humidity to prevent excessive water loss. In addition, the supracoxal glands actively take up ambient water vapour, and the protonynph stage of the life cycle is resistant to desiccation. Larger house-dust-mite populations are found when the absolute indoor air humidity is above 7 g/kg (45% relative humidity at 20 degrees C). Consequently, ventilation by air-conditioning systems is being developed as a means of control. A number of other aspects of the domestic environment are also being manipulated in an integrated approach to render the habitat less suitable for mites. The potential exists for developing models for house-dust mite populations, environmental characteristics, and the effects of various approaches to control.

Developing a new controllable lunar dust simulant: BHLD20

NASA Astrophysics Data System (ADS)

Sun, Hao; Yi, Min; Shen, Zhigang; Zhang, Xiaojing; Ma, Shulin

2017-07-01

Identifying and eliminating the negative effects of lunar dust are of great importance for future lunar exploration. Since the available lunar samples are limited, developing terrestrial lunar dust simulant becomes critical for the study of lunar dust problem. In this work, beyond the three existing lunar dust simulants: JSC-1Avf, NU-LHT-1D, and CLDS-i, we developed a new high-fidelity lunar dust simulant named as BHLD20. And we concluded a methodology that soil and dust simulants can be produced by variations in portions of the overall procedure, whereby the properties of the products can be controlled by adjusting the feedstock preparation and heating process. The key ingredients of our innovative preparation route include: (1) plagioclase, used as a major material in preparing all kinds of lunar dust simulants; (2) a muffle furnace, applied to expediently enrich the glass phase in feedstock, with the production of some composite particles; (3) a one-step sand-milling technique, employed for mass pulverization without wasting feedstock; and (4) a particle dispersant, utilized to prevent the agglomeration in lunar dust simulant and retain the real particle size. Research activities in the development of BHLD20 can help solve the lunar dust problem.

40 CFR 52.478 - Rules and Regulations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... synthesized pharmaceutical products, pneumatic rubber tires, vegetable oil, synthetic organic chemicals...) Graphic arts systems; (9) Storage, transportation and marketing of VOCs (fugitive VOCs from oil and gas...

40 CFR 52.478 - Rules and Regulations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... synthesized pharmaceutical products, pneumatic rubber tires, vegetable oil, synthetic organic chemicals...) Graphic arts systems; (9) Storage, transportation and marketing of VOCs (fugitive VOCs from oil and gas...

Repellent activity of desiccant dusts and conidia of the entomopathogenic fungus Beauveria bassiana when tested against poultry red mites (Dermanyssus gallinae) in laboratory experiments.

PubMed

Kilpinen, Ole; Steenberg, Tove

2016-11-01

Desiccant dusts and entomopathogenic fungi have previously been found to hold potential against the poultry red mite, which is an important pest in egg production and notoriously difficult to control. Both control agents may cause repellence in other arthropods and potentially also influence control levels adversely when used against the poultry red mite. Five desiccant dust products with good efficacy against the poultry red mite Dermanyssus gallinae caused avoidance behavior in mites when tested in bioassays. The repellent activity was correlated with efficacy, which was found to depend on both dose and relative humidity (RH). However, one desiccant dust was significantly less repellent compared to other dusts with similar levels of efficacy. Further, dry conidia of the fungus Beauveria bassiana were also shown to be repellent to poultry red mites, both when applied on its own and when admixed with a low dose of the desiccant dust Diamol. The pick-up of desiccant dust particles and fungus conidia from treated surfaces by mites did not differ depending on RH, whereas the overall efficacy of the two control agents were significantly higher at 75 than at 85 % RH. In addition, the combined effect of the two substances was synergistic when tested in a bioassay where mites could choose whether to cross a treated surface. This is the first time a member of Acari has been shown to be repelled by desiccant dusts and by conidia of an entomopathogenic fungus.

The Ferrofluids Story

NASA Technical Reports Server (NTRS)

1993-01-01

A new Ferrofluidics exclusion seal promises improvement in controlling "fugitive emissions" -vapors that escape into the atmosphere from petroleum refining and chemical processing facilities. These are primarily volatile organic compounds, and their emissions are highly regulated by the EPA. The ferrofluid system consists of a primary mechanical seal working in tandem with a secondary seal. Ferrofluids are magnetic liquids - fluids in which microscopic metal particles have been suspended, allowing the liquid to be controlled by a magnetic force. The concept was developed in the early years of the Space program, but never used. Two Avco scientists, however, saw commercial potential in ferrofluids and formed a company. Among exclusion seal commercial applications are rotary feedthrough seals, hydrodynamic bearings and fluids for home and automotive loudspeakers. Ferrofluidics has subsidiaries throughout the world.

Atopy patch test reactions to house dust mites in patients with scabies.

PubMed

Taşkapan, Oktay; Harmanyeri, Yavuz

2005-01-01

It is well known that the house dust and the scabies mites are related phylogenetically. We therefore performed atopy patch tests with house dust mite antigens (Dermatophagoides pteronyssinus (Dp) and/or Dermatophagoides farinae (Df)) in scabies patients without atopy and healthy controls. We studied 25 men with active scabies and 25 healthy controls. Skin prick tests with standardized house dust mite extract were performed for all patients and controls. An intradermal test procedure was carried out in skin prick test-negative patients, and for controls showing positive atopy patch test to Dp and/or Df. While atopy patch tests were performed directly in all healthy controls, patients with scabies were first treated and on the next day, atopy patch tests were performed. Twenty-two of 25 patients with scabies (88%) had skin prick test and/or intradermal test positivity against house dust mites, whereas 17/25 patients (68%) had atopy patch test positivity against house dust mites (Dp and/or Df). There was no statistically significant difference between skin prick test and/or intradermal test positivity and atopy patch test positivity in a regression analysis (p=0.222). The only statistically significant correlation was between atopy patch test positivity and the extent of scabies involvement (p<0.05). Only few of the healthy controls had positive tests. In this study, we have shown that a positive atopy patch test to house dust mite antigens is not specific for patients with atopic dermatitis, but also occurs in scabies patients without a history of atopic dermatitis.

Analysis of chromosomal aberrations in men occupationally exposed to cement dust.

PubMed

Fatima, S K; Prabhavathi, P A; Padmavathi, P; Reddy, P P

2001-02-20

Cement industry is considered as a major pollution problem on account of dust and particulate matter emitted at various steps of cement manufacture. Cement dust consists of many toxic constituents. The workers who are employed in cement industries are exposed to cement dust for long periods. Therefore, it is mandatory to evaluate the mutagenic effects of occupational exposure to cement dust in such workers. In the present study, we analyzed the samples of 124 male workers including 59 smokers and 65 non-smokers who were employed in cement industry for a period of 1-17 years. For comparison, 106 controls (including 47 smokers and 59 non-smokers) of the same age group and socio-economic status were also studied. Controls had no exposure to cement dust or any known physical or chemical agent. A significant increase in the incidence of chromosomal aberrations was observed in the exposed group when compared to the control group. The results were analyzed separately for non-smokers and smokers. The chromosomal damage was more pronounced in the smokers when compared with the non-smokers both in control and exposed groups. A significant increase in the frequency of chromosomal aberrations was also observed with increase in age in both control and exposed subjects.

Synergistic interaction between the fungus Beauveria bassiana and desiccant dusts applied against poultry red mites (Dermanyssus gallinae).

PubMed

Steenberg, Tove; Kilpinen, Ole

2014-04-01

The poultry red mite, Dermanyssus gallinae, is a major pest in egg production, feeding on laying hens. Widely used non-chemical control methods include desiccant dusts, although their persistence under field conditions is often short. Entomopathogenic fungi may also hold potential for mite control, but these fungi often take several days to kill mites. Laboratory experiments were carried out to study the efficacy of 3 types of desiccant dusts, the fungus Beauveria bassiana and combinations of the two control agents against D. gallinae. There was significant synergistic interaction between each of the desiccant dusts and the fungus, with observed levels of mite mortality significantly higher than those expected for an additive effect (up to 38 % higher). Synergistic interaction between desiccant dust and fungus was found also when different application methods were used for the fungus and at different levels of relative humidity. Although increased levels of mortality were reached due to the synergistic interaction, the speed of lethal action was not influenced by combining the two components. The persistence of the control agents applied separately or in combination did not change over a period of 4 weeks. Overall, combinations of desiccant dusts and fungus conidia seem to hold considerable promise for future non-chemical control of poultry red mites.

Kawasaki syndrome: a controlled study of an outbreak in Wisconsin.

PubMed

Klein, B S; Rogers, M F; Patrican, L A; White, M C; Burgdorfer, W; Schell, W L; Kochel, R L; Marchette, N J; McPherson, J T; Nelson, D B

1986-08-01

The etiology of Kawasaki syndrome remains unestablished, although a possible role has been suggested for exposure to the application of carpet shampoo, house dust mites, and rickettsial infection. During an outbreak of 20 cases of Kawasaki syndrome that occurred in southeastern Wisconsin from November 1982 through March 1983, a case-control study was done of 15 cases and 30 matched controls. The study included questionnaire administration, dust collection from homes, and serum specimen collection. Only one patient had been exposed to a shampooed carpet within 30 days before onset of illness. No differences were noted between cases and controls in the degree of exposure to house dust mite-associated factors in the home, nor in the occurrence, density and species-specific prevalence of house dust mites in the home. Meadow voles exposed to house dust mites from the homes of patients did not develop serologic or pathologic evidence of infection due to rickettsiae in the spotted fever and typhus groups or Coxiella burnetii. Anti-mite-specific immunoglobulin E was not detected in serum specimens from cases or controls. Results from this study do not support hypotheses suggesting that the development of Kawasaki syndrome is associated with exposure to application of carpet shampoo, house dust mites, or rickettsial infection.

Dust control technology usage patterns in the drywall finishing industry.

PubMed

Young-Corbett, Deborah E; Nussbaum, Maury A

2009-06-01

A telephone survey was conducted to quantify drywall finishing industry usage rates of dust control technology, identify barriers to technology adoption, and explore firm owner perception of risk. Industry use of the following technologies was described: wet methods, respiratory protection, pole sanders, ventilated sanders, and low-dust joint compound. A survey instrument composed of both Likert-type scaled items and open-ended items was developed and administered by telephone to the census population of the owners of member firms of trade associations: Finishing Contractors Association and Association of the Wall and Ceiling Industries. Of 857 firms, 264 interviews were completed. Along with descriptive statistics, results were analyzed to examine effects of firm size and union affiliation on responses. Responses to open-ended items were analyzed using content analysis procedures. Firm owners rated the risk of dust to productivity and customer satisfaction as low-moderate. Half rated the dust as having some impact on worker health, with higher impacts indicated by owners of small firms. Among the available control technologies, respiratory protection was used most frequently. Several barriers to implementation of the more effective control technologies were identified. Barriers associated with technology usability, productivity, and cost, as well as misperceptions of risk, should be addressed to improve dust control in the drywall finishing industry.

Health risk impacts analysis of fugitive aromatic compounds emissions from the working face of a municipal solid waste landfill in China.

PubMed

Liu, Yanjun; Liu, Yanting; Li, Hao; Fu, Xindi; Guo, Hanwen; Meng, Ruihong; Lu, Wenjing; Zhao, Ming; Wang, Hongtao

2016-12-01

Aromatic compounds (ACs) emitted from landfills have attracted a lot of attention of the public due to their adverse impacts on the environment and human health. This study assessed the health risk impacts of the fugitive ACs emitted from the working face of a municipal solid waste (MSW) landfill in China. The emission data was acquired by long-term in-situ samplings using a modified wind tunnel system. The uncertainty of aromatic emissions is determined by means of statistics and the emission factors were thus developed. Two scenarios, i.e. 'normal-case' and 'worst-case', were presented to evaluate the potential health risk in different weather conditions. For this typical large anaerobic landfill, toluene was the dominant species owing to its highest releasing rate (3.40±3.79g·m -2 ·d -1 ). Despite being of negligible non-carcinogenic risk, the ACs might bring carcinogenic risks to human in the nearby area. Ethylbenzene was the major health threat substance. The cumulative carcinogenic risk impact area is as far as ~1.5km at downwind direction for the normal-case scenario, and even nearly 4km for the worst-case scenario. Health risks of fugitive ACs emissions from active landfills should be concerned, especially for landfills which still receiving mixed MSW. Copyright © 2016 Elsevier Ltd. All rights reserved.

Measurement of fugitive volatile organic compound emissions from a petrochemical tank farm using open-path Fourier transform infrared spectrometry

NASA Astrophysics Data System (ADS)

Wu, Chang-Fu; Wu, Tzong-gang; Hashmonay, Ram A.; Chang, Shih-Ying; Wu, Yu-Syuan; Chao, Chun-Ping; Hsu, Cheng-Ping; Chase, Michael J.; Kagann, Robert H.

2014-01-01

Fugitive emission of air pollutants is conventionally estimated based on standard emission factors. The Vertical Radial Plume Mapping (VRPM) technique, as described in the US EPA OTM-10, is designed to measure emission flux by directly monitoring the concentration of the plume crossing a vertical plane downwind of the site of interest. This paper describes the evaluation results of implementing VRPM in a complex industrial setting (a petrochemical tank farm). The vertical plane was constructed from five retroreflectors and an open-path Fourier transform infrared spectrometer. The VRPM configuration was approximately 189.2 m in width × 30.7 m in height. In the accompanying tracer gas experiment, the bias of the VRPM estimate was less than 2% and its 95% confidence interval contained the true release rate. Emission estimates of the target VOCs (benzene, m-xylene, o-xylene, p-xylene, and toluene) ranged from 0.86 to 2.18 g s-1 during the 14-day field campaign, while estimates based on the standard emission factors were one order of magnitude lower, possibly leading to an underestimation of the impact of these fugitive emissions on air quality and human health. It was also demonstrated that a simplified 3-beam geometry (i.e., without one dimensional scanning lines) resulted in higher uncertainties in the emission estimates.

The Electrostatic Environments of Mars: Atmospheric Discharges

NASA Technical Reports Server (NTRS)

Calle, Carlos I.; Mackey, Paul J.; Johansen, Michael R.; Hogue, Michael D.; Phillips, James, III; Cox, Rachel E.

2016-01-01

The electrostatic environment on Mars is controlled by its ever present atmospheric dust. Dust devils and dust storms tribocharge this dust. Theoretical studies predict that lightning and/or glow discharges should be present on Mars, but none have been directly observed. Experiments are planned to shed light on this issue.

Evaluation of Brushing as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Journey, Khrissaundra; Christopher, Steven; Davis, Shanon

2011-01-01

Evaluation of brushing to remove lunar simulant dust from thermal control surfaces is described. First, strip brushes made with nylon, PTFE, or Thunderon (Nihon Sanmo Dyeing Company Ltd.) bristles were used to remove JSC-1AF dust from AZ93 thermal control paint or aluminized FEP (AlFEP) thermal control surface under ambient laboratory conditions. Nylon and PTFE bristles removed a promising amount of dust from AZ93, and nylon and Thunderon bristles from AlFEP. But when these were tested under simulated lunar conditions in the lunar dust adhesion bell jar (LDAB), they were not effective. In a third effort, seven brushes made up of three different materials, two different geometries, and different bristle lengths and thicknesses were tested under laboratory conditions against AZ93 and AlFEP. Two of these brushes, the Zephyr fiberglass fingerprint brush and the Escoda nylon fan brush, removed over 90 percent of the dust, and so were tested in the fourth effort in the LDAB. They also performed well under these conditions recovering 80 percent or more of the original thermal performance (solar absorptance/thermal emittance) of both AZ93 and AgFEP after 20 strokes, and 90 or more percent after 200 strokes

Evaluation of Brushing as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Journey, Hhrissaundra; Christopher, Steven; Davis, Shanon

2011-01-01

Evaluation of brushing to remove lunar simulant dust from thermal control surfaces is described. First, strip brushes made with nylon, PTFE, or Thunderon bristles were used to remove JSC-1AF dust from AZ93 thermal control paint or aluminized FEP (AlFEP) thermal control surface under ambient laboratory conditions. Nylon and PTFE bristles removed a promising amount of dust from AZ93, and nylon and Thunderon bristles from AlFEP. But when these were tested under simulated lunar conditions in the lunar dust adhesion bell jar (LDAB), they were not effective. In a third effort, seven brushes made up of three different materials, two different geometries, and different bristle lengths and thicknesses were tested under laboratory conditions against AZ93 and AlFEP. Two of these brushes, the Zephyr fiberglass fingerprint brush and the Escoda nylon fan brush, removed over 90 percent of the dust, and so were tested in the fourth effort in the LDAB. They also performed well under these conditions recovering 80 percent or more of the original thermal performance (solar absorptance/thermal emittance) of both AZ93 and AgFEP after 20 strokes, and 90 or more percent after 200 strokes.

Wood-related occupations, wood dust exposure, and sinonasal cancer.

PubMed

Hayes, R B; Gerin, M; Raatgever, J W; de Bruyn, A

1986-10-01

A case-control study was conducted to examine the relations between type of woodworking and the extent of wood dust exposure to the risks for specific histologic types of sinonasal cancer. In cooperation with the major treatment centers in the Netherlands, 116 male patients newly diagnosed between 1978 and 1981 with primary malignancies of epithelial origin of this site were identified for study. Living controls were selected from the municipal registries, and deceased controls were selected from the national death registry. Interviews were completed for 91 (78%) cases and 195 (75%) controls. Job histories were coded by industry and occupation. An index of exposure was developed to classify the extent of occupational exposure to wood dust. When necessary, adjustment was made for age and usual cigarette use. The risk for nasal adenocarcinoma was elevated by industry for the wood and paper industry (odds ratio (OR) = 11.9) and by occupation for those employed in furniture and cabinet making (OR = 139.8), in factory joinery and carpentry work (OR = 16.3), and in association with high-level wood dust exposure (OR = 26.3). Other types of nasal cancer were not found to be associated with wood-related industries or occupations. A moderate excess in risk for squamous cell cancer (OR = 2.5) was associated with low-level wood dust exposure; however, no dose-response relation was evident. The association between wood dust and adenocarcinoma was strongest for those employed in wood dust-related occupations between 1930 and 1941. The risk of adenocarcinoma did not appear to decrease for at least 15 years after termination of exposure to wood dust. No cases of nasal adenocarcinoma were observed in men whose first exposure to wood dust occurred after 1941.

Dust control for Enabler

NASA Technical Reports Server (NTRS)

Hilton, Kevin; Karl, Chad; Litherland, Mark; Ritchie, David; Sun, Nancy

1992-01-01

The dust control group designed a system to restrict dust that is disturbed by the Enabler during its operation from interfering with astronaut or camera visibility. This design also considers the many different wheel positions made possible through the use of artinuation joints that provide the steering and wheel pitching for the Enabler. The system uses a combination of brushes and fenders to restrict the dust when the vehicle is moving in either direction and in a turn. This design also allows for each of maintenance as well as accessibility of the remainder of the vehicle.

Dust control for Enabler

NASA Technical Reports Server (NTRS)

Hilton, Kevin; Karl, Chad; Litherland, Mark; Ritchie, David; Sun, Nancy

1992-01-01

The dust control group designed a system to restrict dust that is disturbed by the Enabler during its operation from interfering with astronaut or camera visibility. This design also considers the many different wheel positions made possible through the use of artinuation joints that provide the steering and wheel pitching for the Enabler. The system uses a combination of brushes and fenders to restrict the dust when the vehicle is moving in either direction and in a turn. This design also allows for ease of maintenance as well as accessibility of the remainder of the vehicle.

Respirable dust measured downwind during rock dust application.

PubMed

Harris, M L; Organiscak, J; Klima, S; Perera, I E

2017-05-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

Investigating the Hydro-geochemical Impact of Fugitive Methane on Groundwater: The Borden Aquifer Controlled Release Study

NASA Astrophysics Data System (ADS)

Cahill, A. G.; Parker, B. L.; Cherry, J. A.; Mayer, K. U.; Mayer, B.; Ryan, C.

2014-12-01

Shale gas development by hydraulic fracturing is believed by many to have the potential to transform the world's energy economy. The propensity of this technique to cause significant environmental impact is strongly contested and lacks evidence. Fugitive methane (CH4), potentially mobilized during well drilling, the complex extraction process and/or leaking well seals over time is arguably the greatest concern. Advanced understanding of CH4 mobility and fate in the subsurface is needed in order to assess risks, design suitable monitoring systems and gain public trust. Currently knowledge on subsurface CH4 mobilization and migration at scales relevant to shale gas development is lacking. Consequently a shallow aquifer controlled CH4 release experiment is being conducted at the Borden aquifer research facility (an unconfined, unconsolidated silicate sand aquifer) in Ontario, Canada. During the experiment, 100 m3 of gas phase CH4 was injected into the saturated zone over approximately 60 days through 2 inclined sparging wells (4.5 and 9 m depth) at rates relevant to natural gas well casing vent flows. The gas mobility and fate is being comprehensively monitored temporally and spatially in both the saturated and unsaturated zones considering; aqueous chemistry (including stable isotopes), soil gas characterization, surface efflux, geophysics (GPR and ERT), real time sensors (total dissolved gas pressure, soil moisture content, CH4 and CO2), mineralogical and microbiological characterization before, during and after injection. An overview of this unique study will be given including experimental design, monitoring system configuration and preliminary results. This multidisciplinary study will provide important insights regarding the mechanisms and rates for shallow CH4 migration, attenuation and water quality impacts that will inform baseline groundwater monitoring programs and retrospective forensic studies.

Investigating the Hydro-geochemical Impact of Fugitive Methane on Groundwater: The Borden Aquifer Controlled Release Study

NASA Astrophysics Data System (ADS)

Cahill, A. G.; Parker, B. L.; Cherry, J. A.; Mayer, K. U.; Mayer, B.; Ryan, C.

2015-12-01

Shale gas development by hydraulic fracturing is believed by many to have the potential to transform the world's energy economy. The propensity of this technique to cause significant environmental impact is strongly contested and lacks evidence. Fugitive methane (CH4), potentially mobilized during well drilling, the complex extraction process and/or leaking well seals over time is arguably the greatest concern. Advanced understanding of CH4 mobility and fate in the subsurface is needed in order to assess risks, design suitable monitoring systems and gain public trust. Currently knowledge on subsurface CH4 mobilization and migration at scales relevant to shale gas development is lacking. Consequently a shallow aquifer controlled CH4 release experiment is being conducted at the Borden aquifer research facility (an unconfined, unconsolidated silicate sand aquifer) in Ontario, Canada. During the experiment, 100 m3 of gas phase CH4 was injected into the saturated zone over approximately 60 days through 2 inclined sparging wells (4.5 and 9 m depth) at rates relevant to natural gas well casing vent flows. The gas mobility and fate is being comprehensively monitored temporally and spatially in both the saturated and unsaturated zones considering; aqueous chemistry (including stable isotopes), soil gas characterization, surface efflux, geophysics (GPR and ERT), real time sensors (total dissolved gas pressure, soil moisture content, CH4 and CO2), mineralogical and microbiological characterization before, during and after injection. An overview of this unique study will be given including experimental design, monitoring system configuration and preliminary results. This multidisciplinary study will provide important insights regarding the mechanisms and rates for shallow CH4 migration, attenuation and water quality impacts that will inform baseline groundwater monitoring programs and retrospective forensic studies.

Monitoring Volatile Organic Compounds (VOCs) in real-time on oil and natural gas production sites

NASA Astrophysics Data System (ADS)

Lupardus, R.; Franklin, S. B.

2017-12-01

Oil and Natural Gas (O&NG) development, production, infrastructure, and associated processing activities can be a substantial source of air pollution, yet relevant data and real-time quantification methods are lacking. In the current study, O&NG fugitive emissions of Volatile Organic Compounds (VOCs) were quantified in real-time and used to determine the spatial and temporal windows of exposure for proximate flora and fauna. Eleven O&NG sites on the Pawnee National Grassland in Northeastern Colorado were randomly selected and grouped according to production along with 13 control sites from three geographical locations. At each site, samples were collected 25 m from the wellhead in NE, SE, and W directions. In each direction, two samples were collected with a Gasmet DX4040 gas analyzer every hour from 8:00 am to 2:00 pm (6 hours total), July to October, 2016 (N=864). VOC concentrations generally increased during the 6 hr. day with the exception of N2O and were predominately the result of O&NG production and not vehicle exhaust. Thirteen of 24 VOCs had significantly different levels between production groups, frequently above reference standards and at biologically relevant levels for flora and fauna. The most biologically relevant VOCs, found at concentrations exceeding time weighted average permissible exposure limits (TWA PELs), were benzene and acrolein. Generalized Estimating Equations (GEEs) measured the relative quality of statistical models predicting benzene concentrations on sites. The data not only confirms that O&NG emissions are impacting the region, but also that this influence is present at all sites, including controls. Increased real-time VOC monitoring on O&NG sites is required to identify and contain fugitive emissions and to protect human and environmental health.

Sprayed skin turbine component

DOEpatents

Allen, David B

2013-06-04

Fabricating a turbine component (50) by casting a core structure (30), forming an array of pits (24) in an outer surface (32) of the core structure, depositing a transient liquid phase (TLP) material (40) on the outer surface of the core structure, the TLP containing a melting-point depressant, depositing a skin (42) on the outer surface of the core structure over the TLP material, and heating the assembly, thus forming both a diffusion bond and a mechanical interlock between the skin and the core structure. The heating diffuses the melting-point depressant away from the interface. Subsurface cooling channels (35) may be formed by forming grooves (34) in the outer surface of the core structure, filling the grooves with a fugitive filler (36), depositing and bonding the skin (42), then removing the fugitive material.

EVALUATION OF THE PULMONARY TOXICITY OF AMBIENT PARTICULATE MATTER FROM CAMP VICTORY, IRAQ

PubMed Central

Porter, K. L.; Green, F. H. Y.; Harley, R. A.; Vallyathan, V.; Castranova, V.; Waldron, N. R.; Leonard, S. S.; Nelson, D. E.; Lewis, J. A.; Jackson, D. A.

2016-01-01

Anecdotal reports in the press and epidemiological studies suggest that deployment to Iraq and Afghanistan may be associated with respiratory diseases and symptoms in U.S. military personnel and veterans. Exposures during military operations were complex, but virtually all service members were exposed to high levels of respirable, geogenic dust. Inhalation of other dusts has been shown to be associated with adverse health effects, but the pulmonary toxicity of ambient dust from Iraq has not been previously studied. The relative toxicity of Camp Victory dust was evaluated by comparing it to particulate matter from northern Kuwait, a standard U.S. urban dust, and crystalline silica using a single intratracheal instillation in rats. Lung histology, protein levels, and cell counts were evaluated in the bronchoalveolar lavage fluid 1–150 d later. The Iraq dust provoked an early significant, acute inflammatory response. However, the level of inflammation in response to the Iraq dust, U.S. urban dust, and Kuwait dust rapidly declined and was nearly at control levels by the end of the study At later times, animals exposed to the Iraq, U.S. urban, or Kuwait dusts showed increased small airway remodeling and emphysema compared to silica-exposed and control animals without evidence of fibrosis or premalignant changes. The severity and persistence of pulmonary toxicity of these three dusts from the Middle East resemble those of a U.S. urban dust and are less than those of silica. Therefore, Iraq dust exposure is not highly toxic, but similar to other poorly soluble low-toxicity dusts. PMID:26594896

DNA Damage among Wood Workers Assessed with the Comet Assay

PubMed Central

Bruschweiler, Evin Danisman; Wild, Pascal; Huynh, Cong Khanh; Savova-Bianchi, Dessislava; Danuser, Brigitta; Hopf, Nancy B.

2016-01-01

Exposure to wood dust, a human carcinogen, is common in wood-related industries, and millions of workers are occupationally exposed to wood dust worldwide. The comet assay is a rapid, simple, and sensitive method for determining DNA damage. The objective of this study was to investigate the DNA damage associated with occupational exposure to wood dust using the comet assay (peripheral blood samples) among nonsmoking wood workers (n = 31, furniture and construction workers) and controls (n = 19). DNA damage was greater in the group exposed to composite wood products compared to the group exposed to natural woods and controls (P < 0.001). No difference in DNA damage was observed between workers exposed to natural woods and controls (P = 0.13). Duration of exposure and current dust concentrations had no effect on DNA damage. In future studies, workers’ exposures should include cumulative dust concentrations and exposures originating from the binders used in composite wood products. PMID:27398027

Aeolian controls of soil geochemistry and weathering fluxes in high-elevation ecosystems of the Rocky Mountains, Colorado

USGS Publications Warehouse

Lawrence, Corey R.; Reynolds, Richard L.; Kettterer, Michael E.; Neff, Jason C.

2013-01-01

When dust inputs are large or have persisted for long periods of time, the signature of dust additions are often apparent in soils. The of dust will be greatest where the geochemical composition of dust is distinct from local sources of soil parent material. In this study the influence of dust accretion on soil geochemistry is quantified for two different soils from the San Juan Mountains of southwestern Colorado, USA. At both study sites, dust is enriched in several trace elements relative to local rock, especially Cd, Cu, Pb, and Zn. Mass-balance calculations that do not explicitly account for dust inputs indicate the accumulation of some elements in soil beyond what can be explained by weathering of local rock. Most observed elemental enrichments are explained by accounting for the long-term accretion of dust, based on modern isotopic and geochemical estimates. One notable exception is Pb, which based on mass-balance calculations and isotopic measurements may have an additional source at one of the study sites. These results suggest that dust is a major factor influencing the development of soil in these settings and is also an important control of soil weathering fluxes. After accounting for dust inputs in mass-balance calculations, Si weathering fluxes from San Juan Mountain soils are within the range observed for other temperate systems. Comparing dust inputs with mass-balanced based flux estimates suggests dust could account for as much as 50–80% of total long-term chemical weathering fluxes. These results support the notion that dust inputs may sustain chemical weathering fluxes even in relatively young continental settings. Given the widespread input of far-traveled dust, the weathering of dust is likely and important and underappreciated aspect of the global weathering engine.

Aeolian controls of soil geochemistry and weathering fluxes in high-elevation ecosystems of the Rocky Mountains, Colorado

NASA Astrophysics Data System (ADS)

Lawrence, Corey R.; Reynolds, Richard L.; Ketterer, Michael E.; Neff, Jason C.

2013-04-01

When dust inputs are large or have persisted for long periods of time, the signature of dust additions are often apparent in soils. The of dust will be greatest where the geochemical composition of dust is distinct from local sources of soil parent material. In this study the influence of dust accretion on soil geochemistry is quantified for two different soils from the San Juan Mountains of southwestern Colorado, USA. At both study sites, dust is enriched in several trace elements relative to local rock, especially Cd, Cu, Pb, and Zn. Mass-balance calculations that do not explicitly account for dust inputs indicate the accumulation of some elements in soil beyond what can be explained by weathering of local rock. Most observed elemental enrichments are explained by accounting for the long-term accretion of dust, based on modern isotopic and geochemical estimates. One notable exception is Pb, which based on mass-balance calculations and isotopic measurements may have an additional source at one of the study sites. These results suggest that dust is a major factor influencing the development of soil in these settings and is also an important control of soil weathering fluxes. After accounting for dust inputs in mass-balance calculations, Si weathering fluxes from San Juan Mountain soils are within the range observed for other temperate systems. Comparing dust inputs with mass-balanced based flux estimates suggests dust could account for as much as 50-80% of total long-term chemical weathering fluxes. These results support the notion that dust inputs may sustain chemical weathering fluxes even in relatively young continental settings. Given the widespread input of far-traveled dust, the weathering of dust is likely and important and underappreciated aspect of the global weathering engine.

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport

PubMed Central

Shahan, M.R.; Seaman, C.E.; Beck, T.W.; Colinet, J.F.; Mischler, S.E.

2017-01-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. PMID:28936001

Effects of inhaled fine dust on lung tissue changes and antibody response induced by spores of opportunistic fungi in goats.

PubMed

Purdy, Charles W; Layton, Robert C; Straus, David C; Ayers, J R

2008-04-01

To investigate the effects of sterile fine dust aerosol inhalation on antibody responses and lung tissue changes induced by Mucor ramosissimus or Trichoderma viride spores following intratracheal inoculation in goats. 36 weanling Boer-Spanish goats. 6 goats were allocated to each of 2 M ramosissimus-inoculated groups, 2 T viride-inoculated groups, and 2 control (tent or pen) groups. One of each pair of sporetreated groups and the tent control group were exposed 7 times to sterilized fine feedyard dust (mean+/-SD particle diameter, <7.72+/-0.69 microm) for 4 hours in a specially constructed tent. Goats in the 4 fungal treatment groups were inoculated intratracheally 5 times with a fungal spore preparation (30 mL), whereas tent control goats were intratracheally inoculated with physiologic saline (0.9% NaCl) solution (30 mL). Pen control goats were not inoculated or exposed to dust. Goats received an IV challenge with equine RBCs to assess antibody responses to foreign antigens. Postmortem examinations were performed at study completion (day 68) to evaluate lung tissue lesions. 5 of 7 deaths occurred between days 18 and 45 and were attributed to fine dust exposures prior to fungal treatments. Fine dust inhalation induced similar lung lesions and precipitating antibodies among spore-treated goats. Following spore inoculations, dust-exposed goats had significantly more spores per gram of consolidated lung tissue than did their nonexposed counterparts. Fine dust inhalation appeared to decrease the ability of goats to successfully clear fungal spores from the lungs following intratracheal inoculation.

Symptoms, airway responsiveness, and exposure to dust in beech and oak wood workers

PubMed Central

Bohadana, A.; Massin, N.; Wild, P.; Toamain, J.; Engel, S.; Goutet, P.

2000-01-01

OBJECTIVES—To investigate the relation between levels of cumulative exposure to wood dust and respiratory symptoms and the occurrence of bronchial hyperresponsiveness among beech and oak workers.
METHODS—114 Male woodworkers from five furniture factories and 13 male unexposed controls were examined. The unexposed control group was supplemented by 200 male historical controls. Statistical analyses were performed excluding and including the historical controls. Dust concentration was measured by personal sampling methods. Cumulative exposure to dust was calculated for each woodworker by multiplying the duration of the work by the intensity of exposure (years.mg/m3). Bronchial hyperresponsiveness was assessed by the methacholine bronchial challenge test. Subjects were labelled methacholine bronchial challenge positive if forced expiratory volume in 1 second (FEV1) fell by ⩾20%. The linear dose-response slope was calculated as the last dose divided by the total dose given.
RESULTS—443 Dust samples were collected. The median cumulative exposure to dust was 110 years.mg/m3 with lower and upper quartiles at 70 and 160 years.mg/m3 Overall, no declines in FEV1 and forced vital capacity (FVC) were found with increasing exposures. A dose-response relation was found between intensity of exposure on the one hand, and sore throat, increased prevalence of positive methacholine bronchial challenge tests, and steeper dose-response slope, on the other.
CONCLUSION—Exposure to oak and beech dust may lead to the development of sore throat and bronchial hyperresponsiveness.


Keywords: bronchial hyperresponsiveness; wood dust; beech; oak PMID:10810114

22 CFR 95.3 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... legal offices review and analyze information relevant to the case in preparing a recommendation to the... relevant information, the Secretary may decide to surrender the fugitive to the requesting State, to deny...

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality... equipment procedures and records and to interview the employees who conduct the control tests. Two copies of...

Migration of tungsten dust in tokamaks: role of dust-wall collisions

NASA Astrophysics Data System (ADS)

Ratynskaia, S.; Vignitchouk, L.; Tolias, P.; Bykov, I.; Bergsåker, H.; Litnovsky, A.; den Harder, N.; Lazzaro, E.

2013-12-01

The modelling of a controlled tungsten dust injection experiment in TEXTOR by the dust dynamics code MIGRAINe is reported. The code, in addition to the standard dust-plasma interaction processes, also encompasses major mechanical aspects of dust-surface collisions. The use of analytical expressions for the restitution coefficients as functions of the dust radius and impact velocity allows us to account for the sticking and rebound phenomena that define which parts of the dust size distribution can migrate efficiently. The experiment provided unambiguous evidence of long-distance dust migration; artificially introduced tungsten dust particles were collected 120° toroidally away from the injection point, but also a selectivity in the permissible size of transported grains was observed. The main experimental results are reproduced by modelling.

Quantifying the Movement and Dissolution of Fugitive Methane in Shallow Aquifers: Visualization Experiments

NASA Astrophysics Data System (ADS)

Van De Ven, C. J. C.; Mumford, K. G.

2016-12-01

The environmental impact and potential human health implications, specifically from the contamination of groundwater sources, has sparked controversy around shale gas extraction in North America. It is clear that understanding the effects of hydraulic fracturing on shallow fresh water aquifers is of great importance, including the threat of stray gas (also referred to as fugitive methane) on groundwater quality. Faulty wells provide a preferential pathway for free gas phase (mostly methane) to migrate from deeper gas-bearing formations of natural gas to shallow aquifers, followed by its dissolution into the surrounding groundwater. An increased understanding of the fate of fugitive methane in shallow aquifers is required to assess the potential risks associated with current and future operations, as well as to better link gas migration, dissolution and the deterioration of groundwater quality. In this study, a series of laboratory experiments were performed using carbon dioxide (CO2) gas as a surrogate for methane to improve our understanding of gas dissolution in groundwater systems. Using CO2, a novel laboratory technique was developed that allows the measurement of dissolved CO2 concentrations using image analysis alongside visualization of free gas mobilization. The technique is based on the acidification of water during CO2 dissolution, which causes a colour change in an indicator dye. The colour change is recorded using a visual light transmission technique, in which digital images are used to track dissolved concentrations at high spatial (1 mm) and temporal (5 s) resolutions in a two-dimensional (25 × 25 × 1 cm3) flow cell. The experiments were completed in both homogeneous sand packs and sand packs containing layered heterogeneities to investigate the dissolution of both gas fingers and gas pools. The results demonstrate the potential of this novel technique for investigating gas dissolution, and showed significant tailing of dissolved CO2 and persistence of other gas phase components. This technique will aid in the development of conceptual models to link fugitive methane to groundwater contamination and provide detailed data required for the validation of numerical models that account for gas-water mass transfer; both of which are required for the development of sound monitoring techniques.

Constraining Methane Emissions from Natural Gas Production in Northeastern Pennsylvania Using Aircraft Observations and Mesoscale Modeling

NASA Astrophysics Data System (ADS)

Barkley, Z.; Davis, K.; Lauvaux, T.; Miles, N.; Richardson, S.; Martins, D. K.; Deng, A.; Cao, Y.; Sweeney, C.; Karion, A.; Smith, M. L.; Kort, E. A.; Schwietzke, S.

2015-12-01

Leaks in natural gas infrastructure release methane (CH4), a potent greenhouse gas, into the atmosphere. The estimated fugitive emission rate associated with the production phase varies greatly between studies, hindering our understanding of the natural gas energy efficiency. This study presents a new application of inverse methodology for estimating regional fugitive emission rates from natural gas production. Methane observations across the Marcellus region in northeastern Pennsylvania were obtained during a three week flight campaign in May 2015 performed by a team from the National Oceanic and Atmospheric Administration (NOAA) Global Monitoring Division and the University of Michigan. In addition to these data, CH4 observations were obtained from automobile campaigns during various periods from 2013-2015. An inventory of CH4 emissions was then created for various sources in Pennsylvania, including coalmines, enteric fermentation, industry, waste management, and unconventional and conventional wells. As a first-guess emission rate for natural gas activity, a leakage rate equal to 2% of the natural gas production was emitted at the locations of unconventional wells across PA. These emission rates were coupled to the Weather Research and Forecasting model with the chemistry module (WRF-Chem) and atmospheric CH4 concentration fields at 1km resolution were generated. Projected atmospheric enhancements from WRF-Chem were compared to observations, and the emission rate from unconventional wells was adjusted to minimize errors between observations and simulation. We show that the modeled CH4 plume structures match observed plumes downwind of unconventional wells, providing confidence in the methodology. In all cases, the fugitive emission rate was found to be lower than our first guess. In this initial emission configuration, each well has been assigned the same fugitive emission rate, which can potentially impair our ability to match the observed spatial variability. The current model also does not distinguish between natural gas emissions during the different stages of transportation. We finally discuss the use of additional tracers such as the 13CH4 isotopic ratio and ethane concentrations to separate the various contributors to the regional atmospheric CH4 enhancement.

SPARCLE: Electrostatic Tool for Lunar Dust Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, P. E.; Curtis, S. A.; Minetto, F.

2009-03-16

Successful exploration of most planetary surfaces, with their impact-generated dusty regoliths, will depend on the capabilities to keep surfaces free of the dust which could compromise performance and to collect dust for characterization. Solving the dust problem is essential before we return to the Moon. During the Apollo missions, the discovery was made that regolith fines, or dust, behaved like abrasive velcro, coating surfaces, clogging mechanisms, and making movement progressively more difficult as it was mechanically stirred up during surface operations, and abrading surfaces, including spacesuits, when attempts were made to remove it manually. In addition, some of the astronautsmore » experienced breathing difficulties when exposed to dust that got into the crew compartment. The successful strategy will deal with dust dynamics resulting from interaction between mechanical and electrostatic forces. Here we will describe the surface properties of dust particles, the basis for their behavior, and an electrostatically-based approach and methodology for addressing this issue confirmed by our preliminary results. Our device concept utilizes a focused electron beam to control the electrostatic potential of the surface. A plate of the opposite potential is then used to induce dust migration in the presence of an electrical field. Our goal is a compact device of <5 kg mass and using <5 watts of power to be operational in <5 years with heritage from ionic sweepers for active spacecraft potential control (e.g., on POLAR). Rovers could be fitted with devices that could harness the removal of dust for sampling as part of the extended exploration process on Mercury, Mars, asteroids or outer solar system satellites, as well as the Moon.« less

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Loading, Hauling, and Dumping Safety... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

Controlling dust from concrete saw cutting.

PubMed

Shepherd, Susan; Woskie, Susan

2013-01-01

Cutting concrete with gas-powered saws is ubiquitous in the construction industry and a source of exposure to respirable crystalline silica. Volunteers from the New England Laborers Training Center were recruited to participate in a field experiment examining dust reductions through the use of water, from a hose and from a sprayer, as a dust control. In four series of tests, reinforced concrete pipe was cut under both "dry" and "wet" control conditions. Overall, the geometric mean respirable dust concentration for "dry" cutting (14.396 mg/m³) exceeded both types of water-based controls by more than tenfold. Wet cutting reduced the respirable dust concentration by 85% compared with dry cutting when comparing tests paired by person and saw blade (n = 79 pairs). Using a respirable cyclone, a total of 178 samples were taken. Due to the high variability in dust exposure found in this and other studies of saw cutting, the data were examined for potential exposure determinants that contribute to that variability. Using mixed models, three fixed effects were statistically significant: control condition, worker experience, and location. A random effect for subject was included in the model to account for repeated measures. When each of the significant fixed effects was included with the random effect, it was apparent that inclusion of worker experience or location reduced the between-worker component of exposure variability, while inclusion of control condition (wet vs. dry) explained a large portion of the within-subject variability. Overall, the fixed effect variable for control condition explained the largest fraction of the total exposure variability.

27 CFR 555.106 - Certain prohibited distributions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... a fugitive from justice; (3) Is an unlawful user of marijuana, or any depressant or stimulant drug... 50 pounds, intended to be used solely for sporting, recreational, or cultural purposes in antique...

27 CFR 555.106 - Certain prohibited distributions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... a fugitive from justice; (3) Is an unlawful user of marijuana, or any depressant or stimulant drug... 50 pounds, intended to be used solely for sporting, recreational, or cultural purposes in antique...

27 CFR 555.106 - Certain prohibited distributions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... a fugitive from justice; (3) Is an unlawful user of marijuana, or any depressant or stimulant drug... 50 pounds, intended to be used solely for sporting, recreational, or cultural purposes in antique...

Finding Fugitive Sex Offenders Act of 2011

THOMAS, 112th Congress

Sen. Sessions, Jeff [R-AL

2011-03-29

Senate - 12/01/2011 Placed on Senate Legislative Calendar under General Orders. Calendar No. 247. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Identification of specific sources of airborne particles emitted from within a complex industrial (steelworks) site

NASA Astrophysics Data System (ADS)

Beddows, D. C. S.; Harrison, Roy M.

2018-06-01

A case study is provided of the development and application of methods to identify and quantify specific sources of emissions from within a large complex industrial site. Methods include directional analysis of concentrations, chemical source tracers and correlations with gaseous emissions. Extensive measurements of PM10, PM2.5, trace gases, particulate elements and single particle mass spectra were made at sites around the Port Talbot steelworks in 2012. By using wind direction data in conjunction with real-time or hourly-average pollutant concentration measurements, it has been possible to locate areas within the steelworks associated with enhanced pollutant emissions. Directional analysis highlights the Slag Handling area of the works as the most substantial source of elevated PM10 concentrations during the measurement period. Chemical analyses of air sampled from relevant wind directions is consistent with the anticipated composition of slags, as are single particle mass spectra. Elevated concentrations of PM10 are related to inverse distance from the Slag Handling area, and concentrations increase with increased wind speed, consistent with a wind-driven resuspension source. There also appears to be a lesser source associated with Sinter Plant emissions affecting PM10 concentrations at the Fire Station monitoring site. The results are compared with a ME2 study using some of the same data, and shown to give a clearer view of the location and characteristics of emission sources, including fugitive dusts.

Chemical characterization of atmospheric particles and source apportionment in the vicinity of a steelmaking industry.

PubMed

Almeida, S M; Lage, J; Fernández, B; Garcia, S; Reis, M A; Chaves, P C

2015-07-15

The objective of this work was to provide a chemical characterization of atmospheric particles collected in the vicinity of a steelmaking industry and to identify the sources that affect PM10 levels. A total of 94 PM samples were collected in two sampling campaigns that occurred in February and June/July of 2011. PM2.5 and PM2.5-10 were analyzed for a total of 22 elements by Instrumental Neutron Activation Analysis and Particle Induced X-ray Emission. The concentrations of water soluble ions in PM10 were measured by Ion Chromatography and Indophenol-Blue Spectrophotometry. Positive Matrix Factorization receptor model was used to identify sources of particulate matter and to determine their mass contribution to PM10. Seven main groups of sources were identified: marine aerosol identified by Na and Cl (22%), steelmaking and sinter plant represented by As, Cr, Cu, Fe, Ni, Mn, Pb, Sb and Zn (11%), sinter plant stack identified by NH4(+), K and Pb (12%), an unidentified Br source (1.8%), secondary aerosol from coke making and blast furnace (19%), fugitive emissions from the handling of raw material, sinter plant and vehicles dust resuspension identified by Al, Ca, La, Si, Ti and V (14%) and sinter plant and blast furnace associated essentially with Fe and Mn (21%). Copyright © 2015 Elsevier B.V. All rights reserved.

Spatial and temporal characterization of methane plumes from mobile platforms

NASA Astrophysics Data System (ADS)

O'Brien, A.; Wendt, L.; Miller, D. J.; Lary, D. J.; Zondlo, M. A.

2013-12-01

The spatial and temporal characterization of methane plumes from hydraulic fracturing well sites are presented. Methane measurements from the Marcellus shale region obtained using a commercial instrument on a motor vehicle are discussed. Over 100 well sites in the region were sampled and the methane signature in the vicinity of these wells is presented. Additionally, measurements of methane from our open-path instrument flown aboard the UT Dallas AMR Payload Master 100 remote-controlled, electric aircraft in the Barnett shale region are presented. Using our observations of aircraft surveys near well sites and a gaussian plume dispersion model emission estimates of fugitive methane are presented.

Dust exposure and chronic respiratory symptoms among coffee curing workers in Kilimanjaro: a cross sectional study.

PubMed

Sakwari, Gloria; Bråtveit, Magne; Mamuya, Simon H D; Moen, Bente E

2011-11-24

Coffee processing causes organic dust exposure which may lead to development of respiratory symptoms. Previous studies have mainly focused on workers involved in roasting coffee in importing countries. This study was carried out to determine total dust exposure and respiratory health of workers in Tanzanian primary coffee-processing factories. A cross sectional study was conducted among 79 workers in two coffee factories, and among 73 control workers in a beverage factory. Personal samples of total dust (n = 45 from the coffee factories and n = 19 from the control factory) were collected throughout the working shift from the breathing zone of the workers. A questionnaire with modified questions from the American Thoracic Society questionnaire was used to assess chronic respiratory symptoms. Differences between groups were tested by using independent t-tests and Chi square tests. Poisson Regression Model was used to estimate prevalence ratio, adjusting for age, smoking, presence of previous lung diseases and years worked in dusty factories. All participants were male. The coffee workers had a mean age of 40 years and were older than the controls (31 years). Personal total dust exposure in the coffee factories were significantly higher than in the control factory (geometric mean (GM) 1.23 mg/m3, geometric standard deviation (GSD) (0.8) vs. 0.21(2.4) mg/m3). Coffee workers had significantly higher prevalence than controls for cough with sputum (23% vs. 10%; Prevalence ratio (PR); 2.5, 95% CI 1.0-5.9) and chest tightness (27% vs. 13%; PR; 2.4, 95% CI 1.1-5.2). The prevalence of morning cough, cough with and without sputum for 4 days or more in a week was also higher among coffee workers than among controls. However, these differences were not statistically significant. Workers exposed to coffee dust reported more respiratory symptoms than did the controls. This might relate to their exposure to coffee dust. Interventions for reduction of dust levels and provision of respiratory protective equipment are recommended.

Dust exposure and chronic respiratory symptoms among coffee curing workers in Kilimanjaro: a cross sectional study

PubMed Central

2011-01-01

Background Coffee processing causes organic dust exposure which may lead to development of respiratory symptoms. Previous studies have mainly focused on workers involved in roasting coffee in importing countries. This study was carried out to determine total dust exposure and respiratory health of workers in Tanzanian primary coffee-processing factories. Methods A cross sectional study was conducted among 79 workers in two coffee factories, and among 73 control workers in a beverage factory. Personal samples of total dust (n = 45 from the coffee factories and n = 19 from the control factory) were collected throughout the working shift from the breathing zone of the workers. A questionnaire with modified questions from the American Thoracic Society questionnaire was used to assess chronic respiratory symptoms. Differences between groups were tested by using independent t-tests and Chi square tests. Poisson Regression Model was used to estimate prevalence ratio, adjusting for age, smoking, presence of previous lung diseases and years worked in dusty factories. Results All participants were male. The coffee workers had a mean age of 40 years and were older than the controls (31 years). Personal total dust exposure in the coffee factories were significantly higher than in the control factory (geometric mean (GM) 1.23 mg/m3, geometric standard deviation (GSD) (0.8) vs. 0.21(2.4) mg/m3). Coffee workers had significantly higher prevalence than controls for cough with sputum (23% vs. 10%; Prevalence ratio (PR); 2.5, 95% CI 1.0 - 5.9) and chest tightness (27% vs. 13%; PR; 2.4, 95% CI 1.1 - 5.2). The prevalence of morning cough, cough with and without sputum for 4 days or more in a week was also higher among coffee workers than among controls. However, these differences were not statistically significant. Conclusion Workers exposed to coffee dust reported more respiratory symptoms than did the controls. This might relate to their exposure to coffee dust. Interventions for reduction of dust levels and provision of respiratory protective equipment are recommended. PMID:22114929

A Three-Year Course of House Dust Mite Sublingual Immunotherapy Appears Effective in Controlling the Symptoms of Allergic Rhinitis.

PubMed

Novakova, Silviya M; Novakova, Plamena I; Yakovliev, Plamen H; Staevska, Maria T; Mateva, Nonka G; Dimcheva, Teodora D; Peichev, Jivko L

2018-05-01

Background Allergic rhinitis is the most common allergic disorder. Although the management of the disease is successful in many patients, based on guidelines, some of them remain with symptoms uncontrolled with pharmacotherapy. Presently, there is no substantiated information on the control of allergic rhinitis in patients who underwent sublingual immunotherapy. Objective The purpose of this prospective follow-up study was to assess the control of allergic rhinitis in adults after a three-year course of house dust mite sublingual immunotherapy. Methods This prospective real-life study was designed to include adults with moderate to severe allergic rhinitis sensitized to house dust mite who underwent a three-year course of sublingual immunotherapy. Control of symptoms was assessed by Rhinitis Control Assessment Test (RCAT) after three years of house dust mite sublingual immunotherapy. Additionally, patients assessed their symptoms by utilizing a visual analog scale. Results A total number of 86 consecutively enrolled patients (46 (53.49%) men; mean age 26.10 years (SD = 5.85)) with moderate to severe allergic rhinitis and clinically relevant sensitization to house dust mite were evaluated. When assessed by RCAT on the third year, 74 (86.05%) had well-controlled symptoms and 20 (27.03%) of them were completely controlled. A significant reduction in visual analog scale scores-from 7.52 cm at baseline to 2.31 cm-was established ( P < 0.0001). There was a strong negative correlation between RCAT scores and visual analog scale (r = -0.65; P < 0.01). Conclusion This study provided evidence that a three-year course of house dust mite sublingual immunotherapy appears effective in controlling the symptoms of allergic rhinitis.

Polycyclic Aromatic Hydrocarbons in Residential Dust and Risk of Childhood Acute Lymphoblastic Leukemia

PubMed Central

Deziel, NC; Rull, RP; Colt, JS; Reynolds, P; Whitehead, TP; Gunier, RB; Month, SR; Taggart, DR; Buffler, P; Ward, MH; Metayer, C

2014-01-01

Several polycyclic aromatic hydrocarbons (PAHs) are known or probable human carcinogens. We evaluated the relationship between PAH exposure and risk of childhood acute lymphoblastic leukemia (ALL) using concentrations in residential dust as an exposure indicator. We conducted a population-based case-control study (251 ALL cases, 306 birth-certificate controls) in Northern and Central California from 2001–2007. We collected residential dust using a high volume small surface sampler (HVS3) (n=185 cases, 212 controls) or by sampling from participants’ household vacuum cleaners (n=66 cases, 94 controls). We evaluated log-transformed concentrations of 9 individual PAHs, the summed PAHs, and the summed PAHs weighted by their carcinogenic potency (the toxic equivalence). We calculated odds ratios (ORs) and 95% confidence intervals (CI) using logistic regression adjusting for demographic characteristics and duration between diagnosis/reference date and dust collection. Among participants with HVS3 dust, risk of ALL was not associated with increasing concentration of any PAHs (based on OR per ln(ng/g). Among participants with vacuum dust, we observed positive associations between ALL risk and increasing concentrations of benzo[a]pyrene (OR per ln[ng/g]=1.42, 95% CI=0.95, 2.12), dibenzo[a,h]anthracene (OR=1.98, 95% CI=1.11, 3.55), benzo[k]fluoranthene (OR=1.71, 95% CI= 0.91, 3.22), indeno[1,2,3-cd]pyrene (OR=1.81, 95% CI=1.04, 3.16), and the toxic equivalence (OR=2.35, 95% CI=1.18, 4.69). The increased ALL risk among participants with vacuum dust suggests that PAH exposure may increase the risk of childhood ALL; however, reasons for the different results based on HVS3 dust samples deserve further study. PMID:24948546

Particle Removal by Electrostatic and Dielectrophoretic Forces for Dust Control During Lunar Exploration Missions

NASA Technical Reports Server (NTRS)

Calle, C. I.; Buhler, C. R.; McFall, J. L.; Snyder, S. J.

2009-01-01

Particle removal during lunar exploration activities is of prime importance for the success of robotic and human exploration of the moon. We report on our efforts to use electrostatic and dielectrophoretic forces to develop a dust removal technology that prevents the accumulation of dust on solar panels and removes dust adhering to those surfaces. Testing of several prototypes showed solar shield output above 90% of the initial potentials after dust clearing.

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

Dust control effectiveness of drywall sanding tools.

PubMed

Young-Corbett, Deborah E; Nussbaum, Maury A

2009-07-01

In this laboratory study, four drywall sanding tools were evaluated in terms of dust generation rates in the respirable and thoracic size classes. In a repeated measures study design, 16 participants performed simulated drywall finishing tasks with each of four tools: (1) ventilated sander, (2) pole sander, (3) block sander, and (4) wet sponge. Dependent variables of interest were thoracic and respirable breathing zone dust concentrations. Analysis by Friedman's Test revealed that the ventilated drywall sanding tool produced significantly less dust, of both size classes, than did the other three tools. The pole and wet sanders produced significantly less dust of both size classes than did the block sander. The block sander, the most commonly used tool in drywall finishing operations, produced significantly more dust of both size classes than did the other three tools. When compared with the block sander, the other tools offer substantial dust reduction. The ventilated tool reduced respirable concentrations by 88% and thoracic concentrations by 85%. The pole sander reduced respirable concentrations by 58% and thoracic by 50%. The wet sander produced reductions of 60% and 47% in the respirable and thoracic classes, respectively. Wet sponge sanders and pole sanders are effective at reducing breathing-zone dust concentrations; however, based on its superior dust control effectiveness, the ventilated sander is the recommended tool for drywall finishing operations.

Fabrication of porous titanium scaffold materials by a fugitive filler method.

PubMed

Hong, T F; Guo, Z X; Yang, R

2008-12-01

A clean powder metallurgy route was developed here to produce Ti foams, using a fugitive polymeric filler, polypropylene carbonate (PPC), to create porosities in a metal-polymer compact at the pre-processing stage. The as-produced foams were studied by scanning electron microscopy (SEM), LECO combustion analyses and X-ray diffraction (XRD). Compression tests were performed to assess their mechanical properties. The results show that titanium foams with open pores can be successfully produced by the method. The compressive strength and modulus of the foams decrease with an increasing level of porosity and can be tailored to those of the human bones. After alkali treatment and soaking in a simulated body fluid (SBF) for 3 days, a thin apatite layer was formed along the Ti foam surfaces, which provides favourable bioactive conditions for bone bonding and growth.

Autonomous mobile platform for monitoring air emissions from industrial and municipal wastewater ponds.

PubMed

Fu, Long; Huda, Quamrul; Yang, Zheng; Zhang, Lucas; Hashisho, Zaher

2017-11-01

Significant amounts of volatile organic compounds and greenhouse gases are generated from wastewater lagoons and tailings ponds in Alberta, Canada. Accurate measurements of these air pollutants and greenhouse gases are needed to support management and regulatory decisions. A mobile platform was developed to measure air emissions from tailings pond in the oil sands region of Alberta. The mobile platform was tested in 2015 in a municipal wastewater treatment lagoon. With a flux chamber and a CO 2 /CH 4 sensor on board, the mobile platform was able to measure CO 2 and CH 4 emissions over two days at two different locations in the pond. Flux emission rates of CO 2 and CH 4 that were measured over the study period suggest the presence of aerobic and anaerobic zones in the wastewater treatment lagoon. The study demonstrated the capabilities of the mobile platform in measuring fugitive air emissions and identified the potential for the applications in air and water quality monitoring programs. The Mobile Platform demonstrated in this study has the ability to measure greenhouse gas (GHG) emissions from fugitive sources such as municipal wastewater lagoons. This technology can be used to measure emission fluxes from tailings ponds with better detection of spatial and temporal variations of fugitive emissions. Additional air and water sampling equipment could be added to the mobile platform for a broad range of air and water quality studies in the oil sands region of Alberta.

Global Gene Expression Profiling in Lung Tissues of Rat Exposed to Lunar Dust Particles

NASA Technical Reports Server (NTRS)

Yeshitla, Samrawit A.; Lam, Chiu-Wing; Kidane, Yared H.; Feiveson, Alan H.; Ploutz-Snyder, Robert; Wu, Honglu; James, John T.; Meyers, Valerie E.; Zhang, Ye

2014-01-01

The Moon's surface is covered by a layer of fine, potential reactive dust. Lunar dust contain about 1-2% respirable very fine dust (less than 3 micrometers). The habitable area of any lunar landing vehicle and outpost would inevitably be contaminated with lunar dust that could pose a health risk. The purpose of the study is to analyze the dynamics of global gene expression changes in lung tissues of rats exposed to lunar dust particles. F344 rats were exposed for 4 weeks (6h/d; 5d/wk) in nose-only inhalation chambers to concentrations of 0 (control air), 2.1, 6.8, 21, and 61 mg/m3 of lunar dust. Animals were euthanized at 1 day and 13 weeks after the last inhalation exposure. After being lavaged, lung tissue from each animal was collected and total RNA was isolated. Four samples of each dose group were analyzed using Agilent Rat GE v3 microarray to profile global gene expression of 44K transcripts. After background subtraction, normalization, and log transformation, t tests were used to compare the mean expression levels of each exposed group to the control group. Correction for multiple testing was made using the method of Benjamini, Krieger, and Yekuteli (1) to control the false discovery rate. Genes with significant changes of at least 1.75 fold were identified as genes of interest. Both low and high doses of lunar dust caused dramatic, dose-dependent global gene expression changes in the lung tissues. However, the responses of lung tissue to low dose lunar dust are distinguished from those of high doses, especially those associated with 61mg/m3 dust exposure. The data were further integrated into the Ingenuity system to analyze the gene ontology (GO), pathway distribution and putative upstream regulators and gene targets. Multiple pathways, functions, and upstream regulators have been identified in response to lunar dust induced damage in the lung tissue.

Review of dust transport and mitigation technologies in lunar and Martian atmospheres

NASA Astrophysics Data System (ADS)

Afshar-Mohajer, Nima; Wu, Chang-Yu; Curtis, Jennifer Sinclair; Gaier, James R.

2015-09-01

Dust resuspension and deposition is a ubiquitous phenomenon in all lunar and Martian missions. The near-term plans to return to the Moon as a stepping stone to further exploration of Mars and beyond bring scientists' attention to development and evaluation of lunar and Martian dust mitigation technologies. In this paper, different lunar and Martian dust transport mechanisms are presented, followed by a review of previously developed dust mitigation technologies including fluidal, mechanical, electrical and passive self-cleaning methods for lunar/Martian installed surfaces along with filtration for dust control inside cabins. Key factors in choosing the most effective dust mitigation technology are recognized to be the dust transport mechanism, energy consumption, environment, type of surface materials, area of the surface and surface functionality. While electrical methods operating at higher voltages are identified to be suitable for small but light sensitive surfaces, pre-treatment of the surface is effective for cleaning thermal control surfaces, and mechanical methods are appropriate for surfaces with no concerns of light blockage, surface abrasion and 100% cleaning efficiency. Findings from this paper can help choose proper surface protection/cleaning for future space explorations. Hybrid techniques combining the advantages of different methods are recommended.

State background checks for gun purchase and firearm deaths: an exploratory study.

PubMed

Sen, Bisakha; Panjamapirom, Anantachai

2012-10-01

This study examines the relationship between the types of background-information check required by states prior to firearm purchases, and firearm homicide and suicide deaths. Negative binomial models are used to analyze state-level data for homicides and suicides in the U.S. from 1996 to 2005. Data on types of background information are retrieved from the Surveys of State Procedures Related to Firearm Sales, and the violent death data are from the WISQARS. Several other state level factors were controlled for. More background checks are associated with fewer homicide (IRR:0.93, 95% CI:0.91-0.96) and suicide (IRR:0.98, 95% CI:0.96-1.00) deaths. Firearm homicide deaths are lower when states have checks for restraining orders (IRR:0.87, 95% CI:0.79-0.95) and fugitive status (IRR:0.79, 95% CI:0.72-0.88). Firearm suicide deaths are lower when states have background checks for mental illness (IRR:0.96, 95% CI:0.92-0.99), fugitive status (IRR:0.95, 95% CI:0.90-0.99) and misdemeanors (IRR:0.95, 95% CI:0.92-1.00). It does not appear that reductions in firearm deaths are offset by increases in non-firearm violent deaths. More extensive background checks prior to gun purchase are mostly associated with reductions in firearm homicide and suicide deaths. Several study limitations are acknowledged, and further research is called for to ascertain causality. Copyright © 2012 Elsevier Inc. All rights reserved.

30 CFR 74.6 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control. 74.6 Section 74.6 Mineral... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality...

Assessment of control strategies for reducing volatile organic compound emissions from the polyvinyl chloride wallpaper production industry in Taiwan.

PubMed

Chang, Chang-Tang; Chiou, Chyow-Shan

2006-05-01

This study attempts to assess the effectiveness of control strategies for reducing volatile organic compound (VOC) emission from the polyvinyl chloride (PVC) wallpaper production industry. In Taiwan, methyl ethyl ketone, TOL, and cyclohexanone have comprised the major content of solvents, accounting for approximately 113,000 t/yr to avoid excessive viscosity of plasticizer dioctyl phthalate (DOP) and to increase facility in working. Emissions of these VOCs from solvents have caused serious odor and worse air quality problems. In this study, 80 stacks in five factories were tested to evaluate emission characteristics at each VOC source. After examining the VOC concentrations in the flue gases and contents, the VOC emission rate before treatment and from fugitive sources was 93,000 and 800 t/yr, respectively. In this study, the semiwet electrostatic precipitator is recommended for use as cost-effective control equipment.

Herschel-ATLAS: Dusty early-type galaxies

NASA Astrophysics Data System (ADS)

Rowlands, K.; Dunne, L.; Maddox, S.

2015-03-01

Early-type galaxies (ETGs) are thought to be devoid of dust and star-formation, having formed most of their stars at early epochs. We present the detection of the dustiest ETGs in a large-area blind submillimetre survey with Herschel (H-ATLAS, Eales et al. 2010), where the lack of pre-selection in other bands makes it the first unbiased survey for cold dust in ETGs. The parent sample of 1087 H-ATLAS galaxies in this study have a >= 5σ detection at 250μm, a reliable optical counterpart to the submillimetre source (Smith et al. 2011) and a spectroscopic redshift from the GAMA survey (Driver et al. 2011). Additionally, we construct a control sample of 1052 optically selected galaxies undetected at 250μm and matched in stellar mass to the H-ATLAS parent sample to eliminate selection effects. ETGs were selected from both samples via visual classifications using SDSS images. Further details can be found in Rowlands et al. (2012). Physical parameters are derived for each galaxy using the multiwavelength spectral energy distribution (SED) fitting code of da Cunha, Charlot and Elbaz (2008), Smith et al. 2012, using an energy balance argument. We investigate the differences between the dusty ETGs and the general ETG population, and find that the H-ATLAS ETGs are more than an order of magnitude dustier than the control ETGs. The mean dust mass of the 42 H-ATLAS ETGs is 5.5 × 107M⊙ (comparable to the dust mass of spirals in our sample), whereas the dust mass of the 233 control ETGs inferred from stacking at optical positions on the 250μm map is (0.8 - 4.0) × 106M⊙ for 25-15 K dust. The average star-formation rate of the H-ATLAS ETGs is 1.0 dex higher than that of control ETGs, and the mean r-band light-weighted age of the H-ATLAS ETGs is 1.8 Gyr younger than the control ETGs. The rest-frame NUV - r colours of the H-ATLAS ETGs are 1.0 magnitudes bluer than the control ETGs, and some ETGs may be transitioning from the blue cloud to the red sequence. Some H-ATLAS ETGs show signs of morphological disturbance and may have undergone recent rejuvenation of their ISM via gas and dust delivered by mergers. It is found that late-type stars cannot produce enough dust to account for that observed in the H-ATLAS ETGs. This indicates that either an external source of dust from mergers is required, a substantial amount of dust grain growth must occur in the ISM, or dust destruction by hot X-ray gas is less efficient than predicted.

The Black Underground: Fugitives from Slavery

ERIC Educational Resources Information Center

Quarles, Benjamin

1969-01-01

A brief account of the activities prior to the American Civil War of those who assisted black slaves in their flight from the South to the Northern States and Canada by an underground railroad movement. (RJ)

Progress in Evaluating Quantitative Optical Gas Imaging

EPA Science Inventory

Development of advanced fugitive emission detection and assessment technologies that facilitate cost effective leak and malfunction mitigation strategies is an ongoing goal shared by industry, regulators, and environmental groups. Optical gas imaging (OGI) represents an importan...

27 CFR 555.106 - Certain prohibited distributions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... was convicted in any court of, a crime punishable by imprisonment for a term exceeding 1 year; (2) Is a fugitive from justice; (3) Is an unlawful user of marijuana, or any depressant or stimulant drug...

The effect of cleanliness control during installation work on the amount of accumulated dust in ducts of new HVAC installations.

PubMed

Holopainen, R; Tuomainen, M; Asikainen, V; Pasanen, P; Säteri, J; Seppänen, O

2002-09-01

The aim of this study was to evaluate the amount of dust in supply air ducts in recently installed ventilation systems. The samples for the determination of dust accumulation were collected from supply air ducts in 18 new buildings that have been constructed according to two different cleanliness control levels classified as category P1 (low oil residues and protected against contaminations) and category P2, as defined in the Classification of Indoor Climate, Construction and Building Materials. In the ducts installed according to the requirements of cleanliness category P1 the mean amount of accumulated dust was 0.9 g/m2 (0.4-2.9 g/m2), and in the ducts installed according to the cleanliness category P2 it was 2.3 g/m2 (1.2-4.9 g/m2). A significant difference was found in the mean amounts of dust between ducts of categories P1 and P2 (P < 0.008). The cleanliness control procedure in category P1 proved to be a useful and effective tool for preventing dust accumulation in new air ducts during the construction process. Additionally, the ducts without residual oil had lower amounts of accumulated dust indicating that the demand for oil free components in the cleanliness classification is reasonable.

Climatic controls of the interannual to decadal variability in Saudi Arabian dust activity: Towards the development of a seasonal prediction tool

NASA Astrophysics Data System (ADS)

Yu, Y.; Notaro, M.; Liu, Z.; Alkolibi, F.; Fadda, E.; Bakhrjy, F.

2013-12-01

Atmospheric dust significantly influences the climate system, as well as human life in Saudi Arabia. Skillful seasonal prediction of dust activity with climatic variables will help prevent some negative social impacts of dust storms. Yet, the climatic regulators on Saudi Arabian dust activity remain largely unaddressed. Remote sensing and station observations show consistent seasonal cycles in Saudi Arabian dust activity, which peaks in spring and summer. The climatic controls on springtime and summertime Saudi Arabian dust activity during 1975-2010 are studied using observational and reanalysis data. Empirical Orthogonal Function (EOF) of the observed Saudi Arabian dust storm frequency shows a dominant homogeneous pattern across the country, which has distinct interannual and decadal variations, as revealed by the power spectrum. Regression and correlation analyses reveal that Saudi Arabian dust activity is largely tied to precipitation on the Arabian Peninsula in spring and northwesterly (Shamal) wind in summer. On the seasonal-interannual time scale, warm El Niño-Southern Oscillation (ENSO) phase (El Niño) in winter-to-spring inhibits spring dust activity by increasing the precipitation over the Rub'al Khali Desert, a major dust source region on the southern Arabian Peninsula; warm ENSO and warm Indian Ocean Basin Mode (IOBM) in winter-to-spring favor less summer dust activity by producing anomalously low sea-level pressure over eastern north Africa and Arabian Peninsula, which leads to the reduced Shamal wind speed. The decadal variation in dust activity is likely associated with the Atlantic Multidecadal Oscillation (AMO), which impacts Sahel rainfall and North African dust, and likely dust transport to Saudi Arabia. The Pacific Decadal Oscillation (PDO) and tropical Indian Ocean SST also have influence on the decadal variation in Saudi Arabian dust activity, by altering precipitation over the Arabian Peninsula and summer Shamal wind speed. Using eastern tropical Pacific SST as the high-frequency predictor and antecedent accumulated precipitation over the Arabian Peninsula and North Africa as low-frequency predictors, the predicted seasonal dust activity over Saudi Arabia is well correlated with the original time series (correlation above 0.6).

Bioaccessibility of Fipronil Sorbed to Soil and House Dust

EPA Science Inventory

Fipronil is a phenylpyrazole insecticide with uses ranging from soil treatment, to the control of household pests and ectoparasites on pets. Soils and house dusts readily sorb fipronil and when these soils and dusts are ingested, the fipronil may become bioaccessible for uptake ...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: DUST SUPPRESSANT PRODUCTS: NORTH AMERICAN SALT COMPANY'S DUSTGARD

EPA Science Inventory

Dust suppressant products used to control particulate emissions from unpaved roads are among the technologies evaluated by the Air Pollution Control Technology (APCT) Verification Center, part of the U.S. Environmental Protection Agency's Environmental Technology Verification (ET...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: DUST SUPPRESSANT PRODUCTS: SYNTECH PRODUCTS CORPORATION'S TECHSUPPRESS

EPA Science Inventory

Dust suppressant products used to control particulate emissions from unpaved roads are among the technologies evaluated by the Air Pollution Control Technology (APCT) Verification Center, part of the U.S. Environmental Protection Agency's Environmental Technology Verification (ET...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: DUST SUPPRESSANT PRODUCTS: SYNTECH PRODUCTS CORPORATION'S PETROTAC

EPA Science Inventory

Dust suppressant products used to control particulate emissions from unpaved roads are among the technologies evaluated by the Air Pollution Control Technology (APCT) Verification Center, part of the U.S. Environmental Protection Agency's Environmental Technology Verification (ET...

Injurious effects of wool and grain dusts on alveolar epithelial cells and macrophages in vitro.

PubMed Central

Brown, D M; Donaldson, K

1991-01-01

Epidemiological studies of workers in wool textile mills have shown a direct relation between the concentration of wool dust in the air and respiratory symptoms. Injurious effects of wool dust on the bronchial epithelium could be important in causing inflammation and irritation. A pulmonary epithelial cell line in vitro was therefore used to study the toxic effects of wool dust. Cells of the A549 epithelial cell line were labelled with 51Cr and treated with whole wool dusts and extracts of wool, after which injury was assessed. Also, the effects of grain dust, which also causes a form of airway obstruction, were studied. The epithelial injury was assessed by measuring 51Cr release from cells as an indication of lysis, and by monitoring cells which had detached from the substratum. No significant injury to A549 cells was caused by culture with any of the dusts collected from the air but surface "ledge" dust caused significant lysis at some doses. Quartz, used as a toxic control dust, caused significant lysis at the highest concentration of 100 micrograms/well. To determine whether any injurious material was soluble the dusts were incubated in saline and extracts collected. No extracts caused significant injury to epithelial cells. A similar lack of toxicity was found when 51Cr labelled control alveolar macrophages were targets for injury. Significant release of radiolabel was evident when macrophages were exposed to quartz at concentrations of 10 and 20 micrograms/well, there being no significant injury with either wool or grain dusts. These data suggest that neither wool nor grain dust produce direct injury to epithelial cells, and further studies are necessary to explain inflammation leading to respiratory symptoms in wool and grain workers. PMID:2015211

Effect of energetic electrons on dust charging in hot cathode filament discharge

NASA Astrophysics Data System (ADS)

Kakati, B.; Kausik, S. S.; Saikia, B. K.; Bandyopadhyay, M.

2011-03-01

The effect of energetic electrons on dust charging for different types of dust is studied in hydrogen plasma. The hydrogen plasma is produced by hot cathode filament discharge method in a dusty plasma device. A full line cusped magnetic field cage is used to confine the plasma elements. To study the plasma parameters for various discharge conditions, a cylindrical Langmuir probe having 0.15 mm diameter and 10.0 mm length is used. An electronically controlled dust dropper is used to drop the dust particles into the plasma. For different discharge conditions, the dust current is measured using a Faraday cup connected to an electrometer. The effect of secondary emission as well as discharge voltage on charging of dust grains in hydrogen plasma is studied with different dust.

Effect of asthma management education program on stress and compliance of patients with allergic asthma to house dust mite.

PubMed

Yoo, Yang Sook; Cho, Ok Hee; Kim, Eun Sin; Jeong, Hye Sun

2005-06-01

This study was designed to examine the effect of asthma management education program applied to allergic asthma patients receiving immunotherapy due to house dust mite on their stress and compliance with health care regimens. A quasi experimental design with non-equivalent control group and non-synchronized design was used. The subjects of this study were 61 patients who were receiving immunotherapy at intervals of a week after their symptoms were diagnosed as house dust mite allergic asthma at the pulmonary department of a university hospital in Seoul. They were divided into an experimental group of 29 patients who received asthma management education and a control group of 32 patients. The asthma management education program was composed of group education (once) and reinforcement education (three times) with environmental therapy and immunotherapy to house dust mite. Stress significantly decreased in the experimental group compared to that in the control group. Compliance with health care regimens significantly increased in the experimental group compared to that in the control group. The results suggested that the asthma management education program is effective for the management of stress and the improvement of compliance in patients with allergic asthma to house dust mite.

Deltamethrin flea-control preserves genetic variability of black-tailed prairie dogs during a plague outbreak

USGS Publications Warehouse

Jones, P.H.; Biggins, D.E.; Eads, D.A.; Eads, S.L.; Britten, H.B.

2012-01-01

Genetic variability and structure of nine black-tailed prairie dog (BTPD, Cynomys ludovicianus) colonies were estimated with 15 unlinked microsatellite markers. A plague epizootic occurred between the first and second years of sampling and our study colonies were nearly extirpated with the exception of three colonies in which prairie dog burrows were previously dusted with an insecticide, deltamethrin, used to control fleas (vectors of the causative agent of plague, Yersinia pestis). This situation provided context to compare genetic variability and structure among dusted and non-dusted colonies pre-epizootic, and among the three dusted colonies pre- and post-epizootic. We found no statistical difference in population genetic structures between dusted and non-dusted colonies pre-epizootic. On dusted colonies, gene flow and recent migration rates increased from the first (pre-epizootic) year to the second (post-epizootic) year which suggested dusted colonies were acting as refugia for prairie dogs from surrounding colonies impacted by plague. Indeed, in the dusted colonies, estimated densities of adult prairie dogs (including dispersers), but not juveniles (non-dispersers), increased from the first year to the second year. In addition to preserving BTPDs and many species that depend on them, protecting colonies with deltamethrin or a plague vaccine could be an effective method to preserve genetic variability of prairie dogs. ?? 2011 Springer Science+Business Media B.V.

40 CFR 62.14106 - Emission limits for municipal waste combustor fugitive ash emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the atmosphere from that affected facility visible emissions of combustion ash from an ash conveying... paragraph (a) of this section does cover visible emissions discharged to the atmosphere from buildings or...

Stochastic industrial source detection using lower cost methods

EPA Science Inventory

Hazardous air pollutants (HAPs) can be emitted from a variety of sources in industrial facilities, energy production, and commercial operations. Stochastic industrial sources (SISs) represent a subcategory of emissions from fugitive leaks, variable area sources, malfunctioning p...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: DUST SUPPRESSANT PRODUCTS: MIDWEST INDUSTRIAL SUPPLY, INC.'S ENVIROKLEEN

EPA Science Inventory

Dust suppressant products used to control particulate emissions from unpaved roads are among the technologies evaluated by the Air Pollution Control Technology (APCT) Verification Center, part of the U.S. Environmental Protection Agency's Environmental Technology Verification (ET...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: DUST SUPPRESSANT PRODUCTS: MIDWEST INDUSTRIAL SUPPLY, INC.'S EK35

EPA Science Inventory

Dust suppressant products used to control particulate emissions from unpaved roads are among the technologies evaluated by the Air Pollution Control Technology (APCT) Verification Center, part of the U.S. Environmental Protection Agency's Environmental Technology Verification (ET...

An evaluation of traditional and emerging remote sensing technologies for the detection of fugitive contamination at selected Superfund hazardous waste sites

USGS Publications Warehouse

Slonecker, E. Terrence; Fisher, Gary B.

2011-01-01

This report represents a remote sensing research effort conducted by the U.S. Geological Survey in cooperation with the U.S. Environmental Protection Agency (EPA) for the EPA Office of Inspector General. The objective of this investigation was to explore the efficacy of remote sensing as a technology for postclosure monitoring of hazardous waste sites as defined under the Comprehensive Environmental Response Compensation and Liability Act of 1980 (Public Law 96-510, 42 U.S.C. §9601 et seq.), also known as \\"Superfund.\\" Five delisted Superfund sites in Maryland and Virginia were imaged with a hyperspectral sensor and visited for collection of soil, water, and spectral samples and inspection of general site conditions. This report evaluates traditional and hyperspectral imagery and field spectroscopic measurement techniques in the characterization and analysis of fugitive (anthropogenic, uncontrolled) contamination at previously remediated hazardous waste disposal sites.

Effect of simulated ambient particulate matter exposure on performance, rectal temperature, and leukocytosis of young Spanish goats with or without tilmicosin phosphate.

PubMed

Chirase, N K; Purdy, C W; Avampato, J M

2004-04-01

Dust is an environmental stressor and can become extensive in agricultural production systems. Thirty-six female, Spanish goats (average BW 21.1 kg, SEM = 1.31; age = 4 mo) were randomly assigned to simulated dust events or no dust, with or without tilmicosin phosphate treatment in a 2 x 2 factorial arrangement of treatments to determine effects on performance, rectal temperature, and leukocyte changes. All goats were fed a standard growing diet (13.6% CP) consisting of 37% roughage and 63% concentrate (DM basis). Feed intake was measured daily, and BW (unshrunk) measured individually every 7 d. The tilmicosin-treated group received tilmicosin phosphate (10 mg/kg BW s.c.) before starting the study. Goats exposed to dust were enclosed as a group inside a canvass tent for 4 h each day and ground feed yard manure dust (mean particle size 100 microm) was aerosolized inside the tent to simulate a dust event. There was one single dust event (Phase I) followed by rectal temperature measurement, and heparinized blood collection for complete cell counts at 0 (pretrial), 4, 12, 20, 44, 68, and 210 h after dust exposure. This was followed by 21 d of chronic dust events (Phase II). The sampling procedures for Phase II were exactly the same as in Phase I, except that samples were obtained daily at 0 (before dust application), 4, 8, and 12 h after each dust event. Dust treatment had no effect (P > 0.05) on feed intake or ADG, but the gain:feed (G:F) ratio was lower (P < 0.05) in the control goats than the dust exposed group. Tilmicosin phosphate-treated goats had a higher (P < 0.05) G:F ratio than untreated goats. Dust exposure increased (P < 0.002), but tilmicosin treatment decreased (P < 0.05) rectal temperature at 4 and 8 h. Dust exposure increased (P < 0.02) blood lymphocyte counts compared with controls. These results suggest that simulated dust events altered rectal temperature and leukocyte counts of goats.

Quantification of Fugitive Methane Emissions with Spatially Correlated Measurements Collected with Novel Plume Camera

NASA Astrophysics Data System (ADS)

Tsai, Tracy; Rella, Chris; Crosson, Eric

2013-04-01

Quantification of fugitive methane emissions from unconventional natural gas (i.e. shale gas, tight sand gas, etc.) production, processing, and transport is essential for scientists, policy-makers, and the energy industry, because methane has a global warming potential of at least 21 times that of carbon dioxide over a span of 100 years [1]. Therefore, fugitive emissions reduce any environmental benefits to using natural gas instead of traditional fossil fuels [2]. Current measurement techniques involve first locating all the possible leaks and then measuring the emission of each leak. This technique is a painstaking and slow process that cannot be scaled up to the large size of the natural gas industry in which there are at least half a million natural gas wells in the United States alone [3]. An alternative method is to calculate the emission of a plume through dispersion modeling. This method is a scalable approach since all the individual leaks within a natural gas facility can be aggregated into a single plume measurement. However, plume dispersion modeling requires additional knowledge of the distance to the source, atmospheric turbulence, and local topography, and it is a mathematically intensive process. Therefore, there is a need for an instrument capable of simple, rapid, and accurate measurements of fugitive methane emissions on a per well head scale. We will present the "plume camera" instrument, which simultaneously measures methane at different spatial points or pixels. The spatial correlation between methane measurements provides spatial information of the plume, and in addition to the wind measurement collected with a sonic anemometer, the flux can be determined. Unlike the plume dispersion model, this approach does not require knowledge of the distance to the source and atmospheric conditions. Moreover, the instrument can fit inside a standard car such that emission measurements can be performed on a per well head basis. In a controlled experiment with known releases from a methane tank, a 2-pixel plume camera measured 496 ± 160 sccm from a release of 650 sccm located 21 m away, and 4,180 ± 962 sccm from a release of 3,400 sccm located 49 m away. These results in addition to results with a higher-pixel camera will be discussed. Field campaign data collected with the plume camera pixels mounted onto a vehicle and driven through the natural gas fields in the Uintah Basin (Utah, United States) will also be presented along with the limitations and advantages of the instrument. References: 1. S. Solomon, D. Qin, M. Manning, Z. Chen, M. Marquis, K.B. Averyt, M.Tignor and H.L. Miller (eds.). IPCC, 2007: Climate Change 2007: The Physical Science Basis of the Fourth Assessment Report. Cambridge University Press, Cambridge, United Kingdom and New York, NY, USA. 2. R.W. Howarth, R. Santoro, and A. Ingraffea. "Methane and the greenhouse-gas footprint of natural gas from shale formations." Climate Change, 106, 679 (2011). 3. U.S. Energy Information Administration. "Number of Producing Wells." . Accessed 6 January 2013.

Silica dust exposures during selected construction activities.

PubMed

Flanagan, Mary Ellen; Seixas, Noah; Majar, Maria; Camp, Janice; Morgan, Michael

2003-01-01

This study characterized exposure for dust-producing construction tasks. Eight common construction tasks were evaluated for quartz and respirable dust exposure by collecting 113 personal task period samples for cleanup; demolition with handheld tools; concrete cutting; concrete mixing; tuck-point grinding; surface grinding; sacking and patching concrete; and concrete floor sanding using both time-integrating filter samples and direct-reading respirable dust monitors. The geometric mean quartz concentration was 0.10 mg/m(3) (geometric standard deviation [GSD]=4.88) for all run time samples, with 71% exceeding the threshold limit value. Activities with the highest exposures were surface grinding, tuck-point grinding, and concrete demolition (GM[GSD] of 0.63[4.12], 0.22[1.94], and 0.10[2.60], respectively). Factors recorded each minute were task, tool, work area, respiratory protection and controls used, estimated cross draft, and whether anyone nearby was making dust. Factors important to exposure included tool used, work area configuration, controls employed, cross draft, and in some cases nearby dust. More protective respirators were employed as quartz concentration increased, although respiratory protection was found to be inadequate for 42% of exposures. Controls were employed for only 12% of samples. Exposures were reduced with three controls: box fan for surface grinding and floor sanding, and vacuum/shroud for surface grinding, with reductions of 57, 50, and 71%, respectively. Exposures were higher for sweeping compound, box fan for cleanup, ducted fan dilution, and wetted substrate. Construction masons and laborers are frequently overexposed to silica. The usual protection method, respirators, was not always adequate, and engineering control use was infrequent and often ineffective.