Attitude control system of the Delfi-n3Xt satellite

NASA Astrophysics Data System (ADS)

Reijneveld, J.; Choukroun, D.

2013-12-01

This work is concerned with the development of the attitude control algorithms that will be implemented on board of the Delfi-n3xt nanosatellite, which is to be launched in 2013. One of the mission objectives is to demonstrate Sun pointing and three axis stabilization. The attitude control modes and the associated algorithms are described. The control authority is shared between three body-mounted magnetorquers (MTQ) and three orthogonal reaction wheels. The attitude information is retrieved from Sun vector measurements, Earth magnetic field measurements, and gyro measurements. The design of the control is achieved as a trade between simplicity and performance. Stabilization and Sun pointing are achieved via the successive application of the classical Bdot control law and a quaternion feedback control. For the purpose of Sun pointing, a simple quaternion estimation scheme is implemented based on geometric arguments, where the need for a costly optimal filtering algorithm is alleviated, and a single line of sight (LoS) measurement is required - here the Sun vector. Beyond the three-axis Sun pointing mode, spinning Sun pointing modes are also described and used as demonstration modes. The three-axis Sun pointing mode requires reaction wheels and magnetic control while the spinning control modes are implemented with magnetic control only. In addition, a simple scheme for angular rates estimation using Sun vector and Earth magnetic measurements is tested in the case of gyro failures. The various control modes performances are illustrated via extensive simulations over several orbits time spans. The simulated models of the dynamical space environment, of the attitude hardware, and the onboard controller logic are using realistic assumptions. All control modes satisfy the minimal Sun pointing requirements allowed for power generation.

Study design options in evaluating gene-environment interactions: practical considerations for a planned case-control study of pediatric leukemia.

PubMed

Goodman, Michael; Dana Flanders, W

2007-04-01

We compare methodological approaches for evaluating gene-environment interaction using a planned study of pediatric leukemia as a practical example. We considered three design options: a full case-control study (Option I), a case-only study (Option II), and a partial case-control study (Option III), in which information on controls is limited to environmental exposure only. For each design option we determined its ability to measure the main effects of environmental factor E and genetic factor G, and the interaction between E and G. Using the leukemia study example, we calculated sample sizes required to detect and odds ratio (OR) of 2.0 for E alone, an OR of 10 for G alone and an interaction G x E of 3. Option I allows measuring both main effects and interaction, but requires a total sample size of 1,500 cases and 1,500 controls. Option II allows measuring only interaction, but requires just 121 cases. Option III allows calculating the main effect of E, and interaction, but not the main effect of G, and requires a total of 156 cases and 133 controls. In this case, the partial case-control study (Option III) appears to be more efficient with respect to its ability to answer the research questions for the amount of resources required. The design options considered in this example are not limited to observational epidemiology and may be applicable in studies of pharmacogenomics, survivorship, and other areas of pediatric ALL research.

Data Obtained in the Flight Measurements to Determine the Stability and Control Characteristics of a C-54D Airplane (AAF No. 42-72713) and a Summary of the Test Program

NASA Technical Reports Server (NTRS)

Talmage, Donald B.; Reeder, John P.

1947-01-01

The flight investigation of the C-54D airplane was initiated to determine the necessity of changes or additions to existing handling-qualities requirements to cove the case of instrument approaches with large airplanes. This paper gives a brief synopsis of the results and presents the measured data of tests to determine the stability and control characteristics. It was found that no new requirements were necessary to cover the problems of instrument approaches. The C-54D airplane tested met the Amy and Navy stability and control requirements except for the following items. The control-system friction with autopilot installed vas double that allowed by the requirements. The amount of friction was found to impair the controllability of the airplane in precision flying. The lateral and directional characteristics were good except that the maximum pb/2V was slightly below the minimum required, and the elevator-control forces to obtain the maximum pb/2V at low speeds were above the Army and Navy requirements. The longitudinal stability and control characteristics were good except that the elevator-control forces exceeded the limits of the Army and Navy requirements in turns and in landings. The stalling characteristics were considered good in all conditions with the stall warning in the form of tail buffeting occurring at speeds approximately 5 miles per hour above the stall.

12 CFR Appendix B to Part 741 - Guidance for an Interest Rate Risk Policy and an Effective Program

Code of Federal Regulations, 2013 CFR

2013-01-01

... Measurement Methods C. Components of IRR Measurement Methods V. Internal Controls VI. Decision-Making Informed... effective IRR management program identifies, measures, monitors, and controls IRR and is central to safe and... critical to the control of IRR exposure. All FICUs required to have an IRR policy and program should...

12 CFR Appendix B to Part 741 - Guidance for an Interest Rate Risk Policy and an Effective Program

Code of Federal Regulations, 2014 CFR

2014-01-01

... Measurement Methods C. Components of IRR Measurement Methods V. Internal Controls VI. Decision-Making Informed... effective IRR management program identifies, measures, monitors, and controls IRR and is central to safe and... critical to the control of IRR exposure. All FICUs required to have an IRR policy and program should...

Measuring the efficiency of control rods in the RBMK critical assembly using a model of RKI-1 reactimeter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhitarev, V. E., E-mail: vejitarev@yandex.ru; Lebedev, G. V.; Sergevnin, A. Yu.

2016-12-15

The efficiency of control rods of the RBMK critical assembly is measured in a series of experiments. The aim of measurements is to determine the characteristics of the model of an RKI-1 reactimeter. The RKI-1 reactimeter is intended for measuring the efficiency of control rods when, according to conditions of operation, the metrological certification of results of an experiment is required. Complications with the metrological certification of reactimeters arise owing to the fact that usually calculated corrections to the results of measurements are required. When the RKI-1 reactimeter is used, there is no need to introduce calculated corrections; the resultmore » of measurements is given with the indication of substantiated errors. In connection with this, the metrological certification of the results of measurements using the RKI-1 reactimeter is simplified.« less

76 FR 70091 - Approval and Promulgation of Implementation Plans and Designation of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... reasonable further progress (RFP), reasonable available control measures, and contingency measures under... request. The General Preamble sets forth EPA's view of applicable requirements for purposes of evaluating...) contingency measures is not applicable for purposes of redesignation. Id. Section 172(c)(3) requires...

NEUTRON MULTIPLICITY AND ACTIVE WELL NEUTRON COINCIDENCE VERIFICATION MEASUREMENTS PERFORMED FOR MARCH 2009 SEMI-ANNUAL DOE INVENTORY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dewberry, R.; Ayers, J.; Tietze, F.

The Analytical Development (AD) Section field nuclear measurement group performed six 'best available technique' verification measurements to satisfy a DOE requirement instituted for the March 2009 semi-annual inventory. The requirement of (1) yielded the need for SRNL Research Operations Department Material Control & Accountability (MC&A) group to measure the Pu content of five items and the highly enrich uranium (HEU) content of two. No 14Q-qualified measurement equipment was available to satisfy the requirement. The AD field nuclear group has routinely performed the required Confirmatory Measurements for the semi-annual inventories for fifteen years using sodium iodide and high purity germanium (HpGe)more » {gamma}-ray pulse height analysis nondestructive assay (NDA) instruments. With appropriate {gamma}-ray acquisition modeling, the HpGe spectrometers can be used to perform verification-type quantitative assay for Pu-isotopics and HEU content. The AD nuclear NDA group is widely experienced with this type of measurement and reports content for these species in requested process control, MC&A booking, and holdup measurements assays Site-wide. However none of the AD HpGe {gamma}-ray spectrometers have been 14Q-qualified, and the requirement of reference 1 specifically excluded a {gamma}-ray PHA measurement from those it would accept for the required verification measurements. The requirement of reference 1 was a new requirement for which the Savannah River National Laboratory (SRNL) Research Operations Department (ROD) MC&A group was unprepared. The criteria for exemption from verification were: (1) isotope content below 50 grams; (2) intrinsically tamper indicating or TID sealed items which contain a Category IV quantity of material; (3) assembled components; and (4) laboratory samples. Therefore all (SRNL) Material Balance Area (MBA) items with greater than 50 grams total Pu or greater than 50 grams HEU were subject to a verification measurement. The pass/fail criteria of reference 7 stated 'The facility will report measured values, book values, and statistical control limits for the selected items to DOE SR...', and 'The site/facility operator must develop, document, and maintain measurement methods for all nuclear material on inventory'. These new requirements exceeded SRNL's experience with prior semi-annual inventory expectations, but allowed the AD nuclear field measurement group to demonstrate its excellent adaptability and superior flexibility to respond to unpredicted expectations from the DOE customer. The requirements yielded five SRNL items subject to Pu verification and two SRNL items subject to HEU verification. These items are listed and described in Table 1.« less

A method exploiting direct communication between phasor measurement units for power system wide-area protection and control algorithms.

PubMed

Almas, Muhammad Shoaib; Vanfretti, Luigi

2017-01-01

Synchrophasor measurements from Phasor Measurement Units (PMUs) are the primary sensors used to deploy Wide-Area Monitoring, Protection and Control (WAMPAC) systems. PMUs stream out synchrophasor measurements through the IEEE C37.118.2 protocol using TCP/IP or UDP/IP. The proposed method establishes a direct communication between two PMUs, thus eliminating the requirement of an intermediate phasor data concentrator, data mediator and/or protocol parser and thereby ensuring minimum communication latency without considering communication link delays. This method allows utilizing synchrophasor measurements internally in a PMU to deploy custom protection and control algorithms. These algorithms are deployed using protection logic equations which are supported by all the PMU vendors. Moreover, this method reduces overall equipment cost as the algorithms execute internally in a PMU and therefore does not require any additional controller for their deployment. The proposed method can be utilized for fast prototyping of wide-area measurements based protection and control applications. The proposed method is tested by coupling commercial PMUs as Hardware-in-the-Loop (HIL) with Opal-RT's eMEGAsim Real-Time Simulator (RTS). As illustrative example, anti-islanding protection application is deployed using proposed method and its performance is assessed. The essential points in the method are: •Bypassing intermediate phasor data concentrator or protocol parsers as the synchrophasors are communicated directly between the PMUs (minimizes communication delays).•Wide Area Protection and Control Algorithm is deployed using logic equations in the client PMU, therefore eliminating the requirement for an external hardware controller (cost curtailment)•Effortless means to exploit PMU measurements in an environment familiar to protection engineers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kegel, T.M.

Calibration laboratories are faced with the need to become accredited or registered to one or more quality standards. One requirement common to all of these standards is the need to have in place a measurement assurance program. What is a measurement assurance program? Brian Belanger, in Measurement Assurance Programs: Part 1, describes it as a {open_quotes}quality assurance program for a measurement process that quantifies the total uncertainty of the measurements (both random and systematic components of error) with respect to national or designated standards and demonstrates that the total uncertainty is sufficiently small to meet the user`s requirements.{close_quotes} Rolf Schumachermore » is more specific in Measurement Assurance in Your Own Laboratory. He states, {open_quotes}Measurement assurance is the application of broad quality control principles to measurements of calibrations.{close_quotes} Here, the focus is on one important part of any measurement assurance program: implementation of statistical process control (SPC). Paraphrasing Juran`s Quality Control Handbook, a process is in statistical control if the only observed variations are those that can be attributed to random causes. Conversely, a process that exhibits variations due to assignable causes is not in a state of statistical control. Finally, Carrol Croarkin states, {open_quotes}In the measurement assurance context the measurement algorithm including instrumentation, reference standards and operator interactions is the process that is to be controlled, and its direct product is the measurement per se. The measurements are assumed to be valid if the measurement algorithm is operating in a state of control.{close_quotes} Implicit in this statement is the important fact that an out-of-control process cannot produce valid measurements. 7 figs.« less

40 CFR 51.213 - Transportation control measures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... REQUIREMENTS FOR PREPARATION, ADOPTION, AND SUBMITTAL OF IMPLEMENTATION PLANS Source Survelliance § 51.213 Transportation control measures. (a) The plan must contain procedures for obtaining and maintaining data on... the case of measures based on traffic flow changes or reductions in vehicle use, the data must include...

40 CFR 51.213 - Transportation control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... REQUIREMENTS FOR PREPARATION, ADOPTION, AND SUBMITTAL OF IMPLEMENTATION PLANS Source Survelliance § 51.213 Transportation control measures. (a) The plan must contain procedures for obtaining and maintaining data on... the case of measures based on traffic flow changes or reductions in vehicle use, the data must include...

Online terahertz thickness measurement in films and coatings

NASA Astrophysics Data System (ADS)

Duling, Irl N.; White, Jeffrey S.

2017-02-01

Pulsed terahertz systems are currently being deployed for online process control and quality control of multi-layered products for use in the building products and aerospace industries. While many laboratory applications of terahertz can allow waveforms to be acquired at rates of 1 - 40 Hz, online applications require measurement rates of in excess of 100Hz. The existing technologies of thickness measurement (nuclear, x-ray, or laser gauges) have rates between 100 and 1000 Hz. At these rates, the single waveform bandwidth must still remain at 2THz or above to allow thinner layers to be measured. In the applications where terahertz can provide unique capability (e.g. multi-layer thickness, delamination, density) long-term stability must be guaranteed within the tolerance required by the measurement. This can mean multi-day stability of less than a micron. The software that runs on these systems must be flexible enough to allow multiple product configurations, while maintaining the simplicity required by plant operators. The final requirement is to have systems that can withstand the environmental conditions of the measurement. This might mean qualification in explosive environments, or operation in hot, wet or dusty environments. All of these requirements can put restrictions on not only the voltage of electronic circuitry used, but also the wavelength and optical power used for the transmitter and receiver. The application of terahertz systems to online process control presents unique challenges that not only effect the physical design of the system, but can also effect the choices made on the terahertz technology itself.

Experimental characterization of the effects of pneumatic tubing on unsteady pressure measurements

NASA Technical Reports Server (NTRS)

Whitmore, Stephen A.; Lindsey, William T.; Curry, Robert E.; Gilyard, Glenn B.

1990-01-01

Advances in aircraft control system designs have, with increasing frequency, required that air data be used as flight control feedback. This condition requires that these data be measured with accuracy and high fidelity. Most air data information is provided by pneumatic pressure measuring sensors. Typically unsteady pressure data provided by pneumatic sensing systems are distorted at high frequencies. The distortion is a result of the pressure being transmitted to the pressure sensor through a length of connective tubing. The pressure is distorted by frictional damping and wave reflection. As a result, air data provided all-flush, pneumatically sensed air data systems may not meet the frequency response requirements necessary for flight control augmentation. Both lab and flight test were performed at NASA-Ames to investigate the effects of this high frequency distortion in remotely located pressure measurement systems. Good qualitative agreement between lab and flight data are demonstrated. Results from these tests are used to describe the effects of pneumatic distortion in terms of a simple parametric model.

40 CFR 51.1010 - Requirements for reasonably available control technology (RACT) and reasonably available control...

Code of Federal Regulations, 2010 CFR

2010-07-01

... the list of the potential measures considered by the State, and information and analysis sufficient to.... Potential measures that are reasonably available considering technical and economic feasibility must be...

Grasp Assist Device with Automatic Mode Control Logic

NASA Technical Reports Server (NTRS)

Laske, Evan (Inventor); Davis, Donald R. (Inventor); Ihrke, Chris A. (Inventor)

2018-01-01

A system includes a glove, sensors, actuator assemblies, and controller. The sensors include load sensors which measure an actual grasping force and attitude sensors which determine a glove attitude. The actuator assembly provides a grasp assist force to the glove. Respective locations of work cells in the work environment and permitted work tasks for each work cell are programmed into the controller. The controller detects the glove location and attitude. A work task is selected by the controller for the location. The controller calculates a required grasp assist force using measured actual grasping forces from the load sensors. The required grasp assist force is applied via the glove using the actuator assembly to thereby assist the operator in performing the identified work task.

Control system and method for a power delivery system having a continuously variable ratio transmission

DOEpatents

Frank, Andrew A.

1984-01-01

A control system and method for a power delivery system, such as in an automotive vehicle, having an engine coupled to a continuously variable ratio transmission (CVT). Totally independent control of engine and transmission enable the engine to precisely follow a desired operating characteristic, such as the ideal operating line for minimum fuel consumption. CVT ratio is controlled as a function of commanded power or torque and measured load, while engine fuel requirements (e.g., throttle position) are strictly a function of measured engine speed. Fuel requirements are therefore precisely adjusted in accordance with the ideal characteristic for any load placed on the engine.

Operational space trajectory tracking control of robot manipulators endowed with a primary controller of synthetic joint velocity.

PubMed

Moreno-Valenzuela, Javier; González-Hernández, Luis

2011-01-01

In this paper, a new control algorithm for operational space trajectory tracking control of robot arms is introduced. The new algorithm does not require velocity measurement and is based on (1) a primary controller which incorporates an algorithm to obtain synthesized velocity from joint position measurements and (2) a secondary controller which computes the desired joint acceleration and velocity required to achieve operational space motion control. The theory of singularly perturbed systems is crucial for the analysis of the closed-loop system trajectories. In addition, the practical viability of the proposed algorithm is explored through real-time experiments in a two degrees-of-freedom horizontal planar direct-drive arm. Copyright © 2010 ISA. Published by Elsevier Ltd. All rights reserved.

Reusable Reentry Satellite (RRS): Thermal control trade study

NASA Technical Reports Server (NTRS)

Wallace, Clark

1990-01-01

The design and assessment work performed in defining the on-orbit Thermal Control Subsystem (TCS) requirements for the Reusable Reentry Satellite (RRS) is discussed. Specifically, it describes the hardware and design measures necessary for maintaining the Payload Module (PM) Environmental Control Life Support System (ECLSS) heat exchanger, the hydrazine propellant, and PM water supply within their required temperature limits.

Automatic method of measuring silicon-controlled-rectifier holding current

NASA Technical Reports Server (NTRS)

Maslowski, E. A.

1972-01-01

Development of automated silicon controlled rectifier circuit for measuring minimum anode current required to maintain rectifiers in conducting state is discussed. Components of circuit are described and principles of operation are explained. Illustration of circuit is provided.

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

40 CFR 96.172 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or... Administrator revokes prospectively the certification status of the monitoring system. The data measured and...

Controllable Grid Interface | Grid Modernization | NREL

Science.gov Websites

groundbreaking apparatus for testing and demonstrating advanced controls for wind and solar power generation at requirements. These requirements involve various aspects of renewable power plant operation, including fault respond directly to grid conditions measured on plant terminals, including: "Nasty" and "

Electrostatic discharge control for STDN stations

NASA Technical Reports Server (NTRS)

Mckiernan, J.

1983-01-01

This manual defines the requirements and control methods necessary to control the effect of electrostatic discharges that damage or destroy electronic equipment components. Test procedures for measuring the effectiveness of the control are included.

Precise attitude control of the Stanford relativity satellite.

NASA Technical Reports Server (NTRS)

Bull, J. S.; Debra, D. B.

1973-01-01

A satellite being designed by the Stanford University to measure (with extremely high precision) the effect of General Relativity is described. Specifically, the satellite will measure two relativistic precessions predicted by the theory: the geodetic effect (6.9 arcsec/yr), due solely to motion about the earth, and the motional effect (0.05 arcsec/yr), due to rotation of the earth. The gyro design requirements, including the requirement for precise attitude control and a dynamic model for attitude control synthesis, are discussed. Closed loop simulation of the satellite's natural dynamics on an analog computer is described.

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 96.272 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of or... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 60.115b - Reporting and recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... years. The record required by (c)(1) will be kept for the life of the control equipment. (a) After...) Within 60 days of performing the seal gap measurements required by § 60.113b(b)(1), furnish the... measurement. (iii) The calculations described in § 60.113b (b)(2) and (b)(3). (3) Keep a record of each gap...

40 CFR 60.115b - Reporting and recordkeeping requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... years. The record required by (c)(1) will be kept for the life of the control equipment. (a) After...) Within 60 days of performing the seal gap measurements required by § 60.113b(b)(1), furnish the... measurement. (iii) The calculations described in § 60.113b (b)(2) and (b)(3). (3) Keep a record of each gap...

Control system and method for a power delivery system having a continuously variable ratio transmission

DOEpatents

Frank, A.A.

1984-07-10

A control system and method for a power delivery system, such as in an automotive vehicle, having an engine coupled to a continuously variable ratio transmission (CVT). Totally independent control of engine and transmission enable the engine to precisely follow a desired operating characteristic, such as the ideal operating line for minimum fuel consumption. CVT ratio is controlled as a function of commanded power or torque and measured load, while engine fuel requirements (e.g., throttle position) are strictly a function of measured engine speed. Fuel requirements are therefore precisely adjusted in accordance with the ideal characteristic for any load placed on the engine. 4 figs.

77 FR 50577 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-22

... the drive mechanism of the horizontal stabilizer trim actuator. This AD requires repetitive detailed... horizontal stabilizer trim control system; repetitive measurements for discrepancies of the ballscrew to... lubrication of the horizontal stabilizer trim control system; repetitive measurements for discrepancies of the...

Statistical Characterization of Environmental Error Sources Affecting Electronically Scanned Pressure Transducers

NASA Technical Reports Server (NTRS)

Green, Del L.; Walker, Eric L.; Everhart, Joel L.

2006-01-01

Minimization of uncertainty is essential to extend the usable range of the 15-psid Electronically Scanned Pressure [ESP) transducer measurements to the low free-stream static pressures found in hypersonic wind tunnels. Statistical characterization of environmental error sources inducing much of this uncertainty requires a well defined and controlled calibration method. Employing such a controlled calibration system, several studies were conducted that provide quantitative information detailing the required controls needed to minimize environmental and human induced error sources. Results of temperature, environmental pressure, over-pressurization, and set point randomization studies for the 15-psid transducers are presented along with a comparison of two regression methods using data acquired with both 0.36-psid and 15-psid transducers. Together these results provide insight into procedural and environmental controls required for long term high-accuracy pressure measurements near 0.01 psia in the hypersonic testing environment using 15-psid ESP transducers.

Statistical Characterization of Environmental Error Sources Affecting Electronically Scanned Pressure Transducers

NASA Technical Reports Server (NTRS)

Green, Del L.; Walker, Eric L.; Everhart, Joel L.

2006-01-01

Minimization of uncertainty is essential to extend the usable range of the 15-psid Electronically Scanned Pressure (ESP) transducer measurements to the low free-stream static pressures found in hypersonic wind tunnels. Statistical characterization of environmental error sources inducing much of this uncertainty requires a well defined and controlled calibration method. Employing such a controlled calibration system, several studies were conducted that provide quantitative information detailing the required controls needed to minimize environmental and human induced error sources. Results of temperature, environmental pressure, over-pressurization, and set point randomization studies for the 15-psid transducers are presented along with a comparison of two regression methods using data acquired with both 0.36-psid and 15-psid transducers. Together these results provide insight into procedural and environmental controls required for long term high-accuracy pressure measurements near 0.01 psia in the hypersonic testing environment using 15-psid ESP transducers.

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 60.4172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... certification status of the monitoring system. The data measured and recorded by the monitoring system shall not...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.432 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 60.4172 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures... certification status of the monitoring system. The data measured and recorded by the monitoring system shall not...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.172 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.272 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D of appendix D to part 75 of this chapter... prospectively the certification status of the monitoring system. The data measured and recorded by the...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

40 CFR 97.372 - Out of control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or... monitoring system. The data measured and recorded by the monitoring system shall not be considered valid...

10 CFR 74.59 - Quality assurance and accounting requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... analyses and evaluations of the design, installation, preoperational tests, calibration, and operation of... performed at a pre-determined frequency, indicate a need for recalibration. Calibrations and tests must be... necessary for performance of the material control tests required by § 74.53(b). (e) Measurement control. The...

10 CFR 74.59 - Quality assurance and accounting requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... analyses and evaluations of the design, installation, preoperational tests, calibration, and operation of... performed at a pre-determined frequency, indicate a need for recalibration. Calibrations and tests must be... necessary for performance of the material control tests required by § 74.53(b). (e) Measurement control. The...

Data Driven Synthesis of Three Term Digital Controllers

NASA Astrophysics Data System (ADS)

Keel, Lee H.; Mitra, Sandipan; Bhattacharyya, Shankar P.

This paper presents a method for digital PID and first order controller synthesis based on frequency domain data alone. The techniques given here first determine all stabilizing controllers from measurement data. In both PID and first order controller cases, the only information required are frequency domain data (Nyquist-Bode data) and the number of open-loop RHP poles. Specifically no identification of the plant model is required. Examples are given for illustration.

Continuous performance measurement in flight systems. [sequential control model

NASA Technical Reports Server (NTRS)

Connelly, E. M.; Sloan, N. A.; Zeskind, R. M.

1975-01-01

The desired response of many man machine control systems can be formulated as a solution to an optimal control synthesis problem where the cost index is given and the resulting optimal trajectories correspond to the desired trajectories of the man machine system. Optimal control synthesis provides the reference criteria and the significance of error information required for performance measurement. The synthesis procedure described provides a continuous performance measure (CPM) which is independent of the mechanism generating the control action. Therefore, the technique provides a meaningful method for online evaluation of man's control capability in terms of total man machine performance.

Development of a reference Phasor Measurement Unit (PMU) for the monitoring and control of grid stability and quality

NASA Astrophysics Data System (ADS)

Ndilimabaka, Hervé; Blanc, Isabelle

2014-08-01

This paper discusses the details of the development of a Phasor Measurement Unit regarding the requirements of the IEEE C37.118-2005 synchrophasor standard relative to steady-state conditions on grid monitoring and control. This phasor measurement unit is intended to be used for field tests sooner.

Electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, S.R.

1995-09-12

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydraulic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control. 10 figs.

Electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, Susan R.

1995-01-01

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydrualic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control.

Design and analysis of an automatic method of measuring silicon-controlled-rectifier holding current

NASA Technical Reports Server (NTRS)

Maslowski, E. A.

1971-01-01

The design of an automated SCR holding-current measurement system is described. The circuits used in the measurement system were designed to meet the major requirements of automatic data acquisition, reliability, and repeatability. Performance data are presented and compared with calibration data. The data verified the accuracy of the measurement system. Data taken over a 48-hr period showed that the measurement system operated satisfactorily and met all the design requirements.

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, S.R.

1994-10-25

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control. 123 figs.

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

DOEpatents

Cikanek, Susan R.

1994-01-01

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control.

Diagnostics and control for the steady state and pulsed tokamak DEMO

NASA Astrophysics Data System (ADS)

Orsitto, F. P.; Villari, R.; Moro, F.; Todd, T. N.; Lilley, S.; Jenkins, I.; Felton, R.; Biel, W.; Silva, A.; Scholz, M.; Rzadkiewicz, J.; Duran, I.; Tardocchi, M.; Gorini, G.; Morlock, C.; Federici, G.; Litnovsky, A.

2016-02-01

The present paper is devoted to a first assessment of the DEMO diagnostics systems and controls in the context of pulsed and steady state reactor design under study in Europe. In particular, the main arguments treated are: (i) The quantities to be measured in DEMO and the requirements for the measurements; (ii) the present capability of the diagnostic and control technology, determining the most urgent gaps, and (iii) the program and strategy of the research and development (R&D) needed to fill the gaps. Burn control, magnetohydrodynamic stability, and basic machine protection require improvements to the ITER technology, and moderated efforts in R&D can be dedicated to infrared diagnostics (reflectometry, electron cyclotron emission, polarimetry) and neutron diagnostics. Metallic Hall sensors appear to be a promising candidate for magnetic measurements in the high neutron fluence and long/steady state discharges of DEMO.

Operation of controls on consumer products by physically impaired users.

PubMed

Kanis, H

1993-06-01

The self-reliance of the physically impaired can be seriously jeopardized by their inability to operate everyday products, especially if both upper extremities are impaired. To determine the difficulties impaired users encounter in operating consumer product controls, on-site video recordings were made of subjects suffering from arthritis or a muscular disease. Subjects' force exertion was compared with that of a group of nonimpaired users. The resulting inventory allowed the analysis of the manipulation problems faced by impaired subjects and the development of design recommendations. In this study the force exerted by the subjects and that required to operate the controls were measured. A comparison of the results of these force measurements led to a number of conclusions. This study led to the following design recommendations: the amount of force required to operate controls should be kept as low as possible; the user should not be required to make two manipulations at the same time, such as simultaneously pushing and rotating a control device; pushing is preferable to rotating; and there should be a great degree of freedom to manipulate controls.

Microbiological water methods: quality control measures for Federal Clean Water Act and Safe Drinking Water Act regulatory compliance.

PubMed

Root, Patsy; Hunt, Margo; Fjeld, Karla; Kundrat, Laurie

2014-01-01

Quality assurance (QA) and quality control (QC) data are required in order to have confidence in the results from analytical tests and the equipment used to produce those results. Some AOAC water methods include specific QA/QC procedures, frequencies, and acceptance criteria, but these are considered to be the minimum controls needed to perform a microbiological method successfully. Some regulatory programs, such as those at Code of Federal Regulations (CFR), Title 40, Part 136.7 for chemistry methods, require additional QA/QC measures beyond those listed in the method, which can also apply to microbiological methods. Essential QA/QC measures include sterility checks, reagent specificity and sensitivity checks, assessment of each analyst's capabilities, analysis of blind check samples, and evaluation of the presence of laboratory contamination and instrument calibration and checks. The details of these procedures, their performance frequency, and expected results are set out in this report as they apply to microbiological methods. The specific regulatory requirements of CFR Title 40 Part 136.7 for the Clean Water Act, the laboratory certification requirements of CFR Title 40 Part 141 for the Safe Drinking Water Act, and the International Organization for Standardization 17025 accreditation requirements under The NELAC Institute are also discussed.

Control banding assessment of workers' exposure to indium and its compounds in 13 Japanese indium plants.

PubMed

Higashikubo, Ichiro; Arito, Heihachiro; Ando, Kenji; Araki, Akihiro; Shimizu, Hidesuke; Sakurai, Haruhiko

2018-05-25

This study aimed to assess workers' exposure to indium and its compounds in 55 indium-handling operations among 13 Japanese plants. The surveyed plants were selected from indium-manufacturing plants whose annual indium production exceeded 500 kg. The Control of Substances Hazardous to Health (COSHH) Essentials control banding toolkit, which contains simple scales for hazard levels, quantities in daily use, and "dustiness" characteristics, was used to assess generic risks of indium-handling operations. The operations were then classified into one of four Control Approaches (CAs). There were 35 indium-handling operations classified into CA4 (requires expert advice) and 16 grouped into CA3 (requires containment). There were three operations classified into CA2 (requires engineering controls) and only one into CA1 (requires good general ventilation (GV) and working practices). Of the 51 operations classified as CA4 and CA3, 36 were found to be improperly equipped with local exhaust ventilation, and the remaining 15 operations solely relied on GV practices. Respiratory protective equipment (RPE) used in the 13 indium plants was examined with reference to the recommendations of the COSHH Essentials and Japan's Technical Guidelines. Our findings suggest that stringent engineering control measures and respiratory protection from indium dust are needed to improve indium-handling operations. Our results show that the most common control approach for Japanese indium-handling operations is to require expert advice, including worker health checks for respiratory diseases and exposure measurement by air sampling.

Lateral stability and control tests of the XP-77 airplane in the NACA full-scale tunnel, 16 June 1944

NASA Technical Reports Server (NTRS)

Czarnecki, K. R.; Donlan, C. J.

1976-01-01

Tests were made in the NACA full-scale tunnel to determine the lateral stability and control characteristics of the XP-77 airplane. Measurements were made of the forces and moments on the airplane at various angles of attack and angles of yaw. The measurements were made with the propeller removed and with the propeller installed and operating at various thrust coefficients, and with the landing flaps retracted and deflected. The effects of aileron, elevator, and rudder deflection on control surface effectiveness and hinge moments were determined. The tests were planned to obtain the data required to evaluate as completely as possible the Army Air Force requirements on lateral stability and control for pursuit-type airplanes.

Optimal Attitude Control of Agile Spacecraft Using Combined Reaction Wheel and Control Moment Gyroscope Arrays

DTIC Science & Technology

2015-12-01

10 IMU Inertial Measurement Unit . . . . . . . . . . . . . . . . . . . . . . . . . 11 PS Pseudo...filters to diminish the effect of gyro corruption in the inertial measurement unit ( IMU ) [32]. Therefore, s/c states determined by the hardware...simulator’s IMU hold the required level of accuracy for characterization of the RWCMG system in the current research. Future external state measurement systems

Terrestrial Planet Finder Coronagraph and Enabling Technologies

NASA Technical Reports Server (NTRS)

Ford, Virginia G.

2005-01-01

Starlight suppression research is Stowed in Delta IV-H advancing rapidly to approach the required contrast ratio. The current analysis of the TPF Coronagraph system indicates that it is feasible to achieve the stability required by using developing technologies: a) Wave Front Sensing and Control (DMs, control algorithms, and sensing); b) Laser metrology. Yet needed: a) Property data measured with great precision in the required environments; b) Modeling tools that are verified with testbeds.

Effects of cusped field thruster on the performance of drag-free control system

NASA Astrophysics Data System (ADS)

Cui, K.; Liu, H.; Jiang, W. J.; Sun, Q. Q.; Hu, P.; Yu, D. R.

2018-03-01

With increased measurement tasks of space science, more requirements for the spacecraft environment have been put forward. Those tasks (e.g. the measurement of Earth's steady state gravity field anomalies) lead to the desire for developing drag-free control. Higher requirements for the thruster performance are made due to the demand for the drag-free control system and real-time compensation for non-conservative forces. Those requirements for the propulsion system include wide continuous throttling ability, high resolution, rapid response, low noise and so on. As a promising candidate, the cusped field thruster has features such as the high working stability, the low erosion rate, a long lifetime and the simple structure, so that it is chosen as the thruster to be discussed in this paper. Firstly, the performance of a new cusped field thruster is tested and analyzed. Then a drag-free control scheme based on the cusped field thruster is designed to evaluate the performance of this thruster. Subsequently, the effects of the thrust resolution, transient response time and thrust uncertainty on the controller are calculated respectively. Finally, the performance of closed-loop system is analyzed, and the simulation results verify the feasibility of applying cusped field thruster to drag-free flight in the space science measurement tasks.

Instrument Pointing Control System for the Stellar Interferometry Mission - Planet Quest

NASA Technical Reports Server (NTRS)

Brugarolas, Paul B.; Kang, Bryan

2006-01-01

This paper describes the high precision Instrument Pointing Control System (PCS) for the Stellar Interferometry Mission (SIM) - Planet Quest. The PCS system provides front-end pointing, compensation for spacecraft motion, and feedforward stabilization, which are needed for proper interference. Optical interferometric measurements require very precise pointing (0.03 as, 1-(sigma) radial) for maximizing the interference pattern visibility. This requirement is achieved by fine pointing control of articulating pointing mirrors with feedback from angle tracking cameras. The overall pointing system design concept is presentcd. Functional requirements and an acquisition concept are given. Guide and Science pointing control loops are discussed. Simulation analyses demonstrate the feasibility of the design.

Metrology: Calibration and measurement processes guidelines

NASA Technical Reports Server (NTRS)

Castrup, Howard T.; Eicke, Woodward G.; Hayes, Jerry L.; Mark, Alexander; Martin, Robert E.; Taylor, James L.

1994-01-01

The guide is intended as a resource to aid engineers and systems contracts in the design, implementation, and operation of metrology, calibration, and measurement systems, and to assist NASA personnel in the uniform evaluation of such systems supplied or operated by contractors. Methodologies and techniques acceptable in fulfilling metrology quality requirements for NASA programs are outlined. The measurement process is covered from a high level through more detailed discussions of key elements within the process, Emphasis is given to the flowdown of project requirements to measurement system requirements, then through the activities that will provide measurements with defined quality. In addition, innovations and techniques for error analysis, development of statistical measurement process control, optimization of calibration recall systems, and evaluation of measurement uncertainty are presented.

Playing Hardball with Facilities Expenses.

ERIC Educational Resources Information Center

Fickes, Michael

1997-01-01

Describes one school district manager's tactics for successfully controlling district costs and increasing capital improvements while only marginally increasing the facilities maintenance budget. Highlights guidelines for controlling personnel requirements and cost-reduction methods. Discusses specific cost-control measures involving telephone…

Estimation of excitation forces for wave energy converters control using pressure measurements

NASA Astrophysics Data System (ADS)

Abdelkhalik, O.; Zou, S.; Robinett, R.; Bacelli, G.; Wilson, D.

2017-08-01

Most control algorithms of wave energy converters require prediction of wave elevation or excitation force for a short future horizon, to compute the control in an optimal sense. This paper presents an approach that requires the estimation of the excitation force and its derivatives at present time with no need for prediction. An extended Kalman filter is implemented to estimate the excitation force. The measurements in this approach are selected to be the pressures at discrete points on the buoy surface, in addition to the buoy heave position. The pressures on the buoy surface are more directly related to the excitation force on the buoy as opposed to wave elevation in front of the buoy. These pressure measurements are also more accurate and easier to obtain. A singular arc control is implemented to compute the steady-state control using the estimated excitation force. The estimated excitation force is expressed in the Laplace domain and substituted in the control, before the latter is transformed to the time domain. Numerical simulations are presented for a Bretschneider wave case study.

Treatment Trials for Neonatal Seizures: The Effect of Design on Sample Size

PubMed Central

Stevenson, Nathan J.; Boylan, Geraldine B.; Hellström-Westas, Lena; Vanhatalo, Sampsa

2016-01-01

Neonatal seizures are common in the neonatal intensive care unit. Clinicians treat these seizures with several anti-epileptic drugs (AEDs) to reduce seizures in a neonate. Current AEDs exhibit sub-optimal efficacy and several randomized control trials (RCT) of novel AEDs are planned. The aim of this study was to measure the influence of trial design on the required sample size of a RCT. We used seizure time courses from 41 term neonates with hypoxic ischaemic encephalopathy to build seizure treatment trial simulations. We used five outcome measures, three AED protocols, eight treatment delays from seizure onset (Td) and four levels of trial AED efficacy to simulate different RCTs. We performed power calculations for each RCT design and analysed the resultant sample size. We also assessed the rate of false positives, or placebo effect, in typical uncontrolled studies. We found that the false positive rate ranged from 5 to 85% of patients depending on RCT design. For controlled trials, the choice of outcome measure had the largest effect on sample size with median differences of 30.7 fold (IQR: 13.7–40.0) across a range of AED protocols, Td and trial AED efficacy (p<0.001). RCTs that compared the trial AED with positive controls required sample sizes with a median fold increase of 3.2 (IQR: 1.9–11.9; p<0.001). Delays in AED administration from seizure onset also increased the required sample size 2.1 fold (IQR: 1.7–2.9; p<0.001). Subgroup analysis showed that RCTs in neonates treated with hypothermia required a median fold increase in sample size of 2.6 (IQR: 2.4–3.0) compared to trials in normothermic neonates (p<0.001). These results show that RCT design has a profound influence on the required sample size. Trials that use a control group, appropriate outcome measure, and control for differences in Td between groups in analysis will be valid and minimise sample size. PMID:27824913

Terrestrial Planet Finder cryogenic delay line development

NASA Technical Reports Server (NTRS)

Smythe, Robert F.; Swain, Mark R.; Alvarez-Salazar, Oscar; Moore, James D.

2004-01-01

Delay lines provide the path-length compensation that makes the measurement of interference fringes possible. When used for nulling interferometry, the delay line must control path-lengths so that the null is stable and controlled throughout the measurement. We report on a low noise, low disturbance, and high bandwidth optical delay line capable of meeting the TPF interferometer optical path length control requirements at cryogenic temperatures.

Training of U.S. Air Traffic Controllers. (IDA Report No. R-206).

ERIC Educational Resources Information Center

Henry, James H.; And Others

The report reviews the evolution of existing national programs for air traffic controller training, estimates the number of persons requiring developmental and supplementary training, examines present controller selection and training programs, investigates performance measurement methods, considers standardization and quality control, discusses…

Visibility and aerosol measurement by diode-laser random-modulation CW lidar

NASA Technical Reports Server (NTRS)

Takeuchi, N.; Baba, H.; Sakurai, K.; Ueno, T.; Ishikawa, N.

1986-01-01

Examples of diode laser (DL) random-modulation continuous wave (RM-CW) lidar measurements are reported. The ability of the measurement of the visibility, vertical aerosol profile, and the cloud ceiling height is demonstrated. Although the data shown here were all measured at night time, the daytime measurement is, of course, possible. For that purpose, accurate control of the laser frequency to the center frequency of a narrow band filter is required. Now a new system with a frequency control is under construction.

Control of polysilicon on-film particulates with on-product measurements

NASA Astrophysics Data System (ADS)

Barker, Judith B.; Chain, Elizabeth E.; Plachecki, Vincent E.

1997-08-01

Historically, a number of in-line particle measurements have been performed on separate test wafers included with product wafers during polysilicon processes. By performing film thickness and particulate measurements directly on product wafers, instead, a number of benefits accrue: (1) reduced test wafer usage, (2) reduced test wafer storage requirements, (3) reduced need for equipment to reclaim test wafers, (4) reduced need for direct labor to reclaim test wafers, and (5) reduced engineering 'false alarms' due to incorrectly processed test wafers. Implementation of on-product measurements for the polysilicon diffusion process required a number of changes in both philosophy and methodology. We show the necessary steps to implementation of on-product particle measurements with concern for overall manufacturing efficiency and the need to maintain appropriate control. Particle results from the Tencor 7600 Surfscan are presented.

Direct Torque Control of a Small Wind Turbine with a Sliding-Mode Speed Controller

NASA Astrophysics Data System (ADS)

Sri Lal Senanayaka, Jagath; Karimi, Hamid Reza; Robbersmyr, Kjell G.

2016-09-01

In this paper. the method of direct torque control in the presence of a sliding-mode speed controller is proposed for a small wind turbine being used in water heating applications. This concept and control system design can be expanded to grid connected or off-grid applications. Direct torque control of electrical machines has shown several advantages including very fast dynamics torque control over field-oriented control. Moreover. the torque and flux controllers in the direct torque control algorithms are based on hvsteretic controllers which are nonlinear. In the presence of a sliding-mode speed control. a nonlinear control system can be constructed which is matched for AC/DC conversion of the converter that gives fast responses with low overshoots. The main control objectives of the proposed small wind turbine can be maximum power point tracking and soft-stall power control. This small wind turbine consists of permanent magnet synchronous generator and external wind speed. and rotor speed measurements are not required for the system. However. a sensor is needed to detect the rated wind speed overpass events to activate proper speed references for the wind turbine. Based on the low-cost design requirement of small wind turbines. an available wind speed sensor can be modified. or a new sensor can be designed to get the required measurement. The simulation results will be provided to illustrate the excellent performance of the closed-loop control system in entire wind speed range (4-25 m/s).

An evaluation of legislative measures on electrical and electronic waste in the People's Republic of China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Shan-Shan, E-mail: sschung@hkbu.edu.hk; Zhang Chan, E-mail: abigailchanzhang@gmail.com

2011-12-15

Graphical abstract: Highlights: > The most recent specific WEEE laws of China are reviewed and evaluated. > Take-back requirement is vaguely defined. > The 'environmental expiry date' requirement is redundant. > Use of a 'multiple enforcement body' approach has hampered enforcement. - Abstract: With the increasing number of recycling mishaps in connection with waste electronic and electrical equipment (WEEE) in the People's Republic of China, it is imperative that the handling and recycling of WEEE be sufficiently regulated in China. Regulations covering three major issues, namely, take-back issues, controls on hazardous substances in WEEE and the assurance of good environmentalmore » management in WEEE plants, were promulgated between 2006 and 2008. The evaluation in this country report shows that few of these regulatory measures have performed satisfactorily in terms of enforcement, of public acceptance and of environmental concerns. In brief, the take-back requirements and the associated financial responsibilities are only vaguely defined; the control on hazardous substances and the so-called 'environmental expiry date' requirements cannot be properly enforced, and the resources needed to ensure the satisfactory enforcement of the environmental abatement and pollution control requirements in WEEE plants are overwhelming. In addition, the use of a 'multiple enforcement body' approach to the control of hazardous substances in WEEE is an indication that the Chinese government lacks the determination to properly enforce the relevant legal requirements.« less

75 FR 42672 - Approval and Promulgation of Implementation Plans; New Jersey; 8-hour Ozone Control Measures

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-22

... definition of VOC throughout Title 7, Chapter 27 of the New Jersey Administrative Codes (N.J.A.C.) and... requirements, such as labeling, recordkeeping, and reporting requirements. C. What is EPA's evaluation? The... requirements, recordkeeping requirements, and test methods and compliance procedures. C. What is EPA's...

Plant Demands Require Reliable Instrumentation.

ERIC Educational Resources Information Center

McClain, Terry L.; Goswami, Santosh R.

1979-01-01

Listed are available control parameters including basic definitions and concepts and methods of measurement. The application of these parameters to the control of water and wastewater treatment plants is also outlined. (CS)

49 CFR 192.491 - Corrosion control records.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Corrosion control records. 192.491 Section 192.491... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.491 Corrosion... detail to demonstrate the adequacy of corrosion control measures or that a corrosive condition does not...

49 CFR 192.491 - Corrosion control records.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Corrosion control records. 192.491 Section 192.491... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.491 Corrosion... detail to demonstrate the adequacy of corrosion control measures or that a corrosive condition does not...

49 CFR 192.491 - Corrosion control records.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Corrosion control records. 192.491 Section 192.491... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.491 Corrosion... detail to demonstrate the adequacy of corrosion control measures or that a corrosive condition does not...

49 CFR 192.491 - Corrosion control records.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Corrosion control records. 192.491 Section 192.491... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.491 Corrosion... detail to demonstrate the adequacy of corrosion control measures or that a corrosive condition does not...

49 CFR 192.491 - Corrosion control records.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Corrosion control records. 192.491 Section 192.491... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.491 Corrosion... detail to demonstrate the adequacy of corrosion control measures or that a corrosive condition does not...

A telerobotic digital controller system

NASA Technical Reports Server (NTRS)

Brown, Richard J.

1992-01-01

This system is a network of joint mounted dual axes digital servo-controllers (DDSC), providing control of various joints and end effectors of different robotic systems. This report provides description of and user required information for the Digital Controller System Network (DSCN) and, in particular, the DDSC, Model DDSC-2, developed to perform the controller functions. The DDSC can control 3 phase brushless or brush type DC motors, requiring up to 8 amps. Only four wires, two for power and 2 for serial communication, are required, except for local sensor and motor connections. This highly capable, very flexible, programmable servo-controller, contained on a single, compact printed circuit board measuring only 4.5 x 5.1 inches, is applicable to control systems of all types from sub-arc second precision pointing to control of robotic joints and end effectors. This document concentrates on the robotic applications for the DDSC.

Driver electronics design and control for a total artificial heart linear motor.

PubMed

Unthan, Kristin; Cuenca-Navalon, Elena; Pelletier, Benedikt; Finocchiaro, Thomas; Steinseifer, Ulrich

2018-01-27

For any implantable device size and efficiency are critical properties. Thus, a linear motor for a Total Artificial Heart was optimized with focus on driver electronics and control strategies. Hardware requirements were defined from power supply and motor setup. Four full bridges were chosen for the power electronics. Shunt resistors were set up for current measurement. Unipolar and bipolar switching for power electronics control were compared regarding current ripple and power losses. Here, unipolar switching showed smaller current ripple and required less power to create the necessary motor forces. Based on calculations for minimal power losses Lorentz force was distributed to the actor's four coils. The distribution was determined as ratio of effective magnetic flux through each coil, which was captured by a force test rig. Static and dynamic measurements under physiological conditions analyzed interaction of control and hardware and all efficiencies were over 89%. In conclusion, the designed electronics, optimized control strategy and applied current distribution create the required motor force and perform optimal under physiological conditions. The developed driver electronics and control offer optimized size and efficiency for any implantable or portable device with multiple independent motor coils. Graphical Abstract ᅟ.

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2012 CFR

2012-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2011 CFR

2011-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2014 CFR

2014-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2013 CFR

2013-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

Management of fluid mud in estuaries, bays, and lakes. II: Measurement, modeling, and management

USGS Publications Warehouse

McAnally, W.H.; Teeter, A.; Schoellhamer, David H.; Friedrichs, C.; Hamilton, D.; Hayter, E.; Shrestha, P.; Rodriguez, H.; Sheremet, A.; Kirby, R.

2007-01-01

Techniques for measurement, modeling, and management of fluid mud are available, but research is needed to improve them. Fluid mud can be difficult to detect, measure, or sample, which has led to new instruments and new ways of using existing instruments. Multifrequency acoustic fathometers sense neither density nor viscosity and are, therefore, unreliable in measuring fluid mud. Nuclear density probes, towed sleds, seismic, and drop probes equipped with density meters offer the potential for accurate measurements. Numerical modeling of fluid mud requires solving governing equations for flow velocity, density, pressure, salinity, water surface, plus sediment submodels. A number of such models exist in one-, two-, and three-dimensional form, but they rely on empirical relationships that require substantial site-specific validation to observations. Management of fluid mud techniques can be classified as those that accomplish: Source control, formation control, and removal. Nautical depth, a fourth category, defines the channel bottom as a specific fluid mud density or alternative parameter as safe for navigation. Source control includes watershed management measures to keep fine sediment out of waterways and in-water measures such as structures and traps. Formation control methods include streamlined channels and structures plus other measures to reduce flocculation and structures that train currents. Removal methods include the traditional dredging and transport of dredged material plus agitation that contributes to formation control and/or nautical depth. Conditioning of fluid mud by dredging and aerating offers the possibility of improved navigability. Two examples—the Atchafalaya Bar Channel and Savannah Harbor—illustrate the use of measurements and management of fluid mud.

An Exchange-Only Qubit in Isotopically Enriched 28Si

NASA Astrophysics Data System (ADS)

Gyure, Mark

2015-03-01

We demonstrate coherent manipulation and universal control of a qubit composed of a triple quantum dot implemented in an isotopically enhanced Si/SiGe heterostructure, which requires no local AC or DC magnetic fields for operation. Strong control over tunnel rates is enabled by a dopantless, accumulation-only device design, and an integrated measurement dot enables single-shot measurement. Reduction of magnetic noise is achieved via isotopic purification of the silicon quantum well. We demonstrate universal control using composite pulses and employ these pulses for spin-echo-type sequences to measure both magnetic noise and charge noise. The noise measured is sufficiently low to enable the long pulse sequences required for exchange-only quantum information processing. Sponsored by United States Department of Defense. The views and conclusions contained in this document are those of the authors and should not be interpreted as representing the official policies, either expressly or implied, of the United States Department of Defense or the U.S. Government. Approved for public release, distribution unlimited.

Silver halide fiber optic radiometry for temperature monitoring and control of tissues heated by microwave

NASA Astrophysics Data System (ADS)

Shenfeld, Ofer; Belotserkovsky, Edward; Goldwasser, Benad; Zur, Albert; Katzir, Abraham

1993-02-01

The heating of tissue by microwave radiation has attained a place of importance in various medical fields, such as the treatment of malignancies, urinary retention, and hypothermia. Accurate temperature measurements in these treated tissues is important for treatment planning and for the control of the heating process. It is also important to be able to measure spacial temperature distribution in the tissues because they are heated in a nonuniform way by the microwave radiation. Conventional temperature sensors used today are inaccurate in the presence of microwave radiation and require contact with the heated tissue. Fiber optic radiometry makes it possible to measure temperatures accurately in the presence of microwave radiation and does not require contact with the tissue. Accurate temperature measurements of tissues heated by microwave was obtained using a silver halide optic radiometer, enabling control of the heating process in other regions of the tissue samples. Temperature mappings of the heated tissues were performed and the nonuniform temperature distributions in these tissues was demonstrated.

49 CFR 195.589 - What corrosion control information do I have to maintain?

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false What corrosion control information do I have to... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.589 What corrosion control... sufficient detail to demonstrate the adequacy of corrosion control measures or that corrosion requiring...

49 CFR 195.589 - What corrosion control information do I have to maintain?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false What corrosion control information do I have to... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.589 What corrosion control... sufficient detail to demonstrate the adequacy of corrosion control measures or that corrosion requiring...

49 CFR 195.589 - What corrosion control information do I have to maintain?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false What corrosion control information do I have to... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.589 What corrosion control... sufficient detail to demonstrate the adequacy of corrosion control measures or that corrosion requiring...

49 CFR 195.589 - What corrosion control information do I have to maintain?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false What corrosion control information do I have to... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.589 What corrosion control... sufficient detail to demonstrate the adequacy of corrosion control measures or that corrosion requiring...

49 CFR 195.589 - What corrosion control information do I have to maintain?

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false What corrosion control information do I have to... SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Corrosion Control § 195.589 What corrosion control... sufficient detail to demonstrate the adequacy of corrosion control measures or that corrosion requiring...

Nonparametric method for failures diagnosis in the actuating subsystem of aircraft control system

NASA Astrophysics Data System (ADS)

Terentev, M. N.; Karpenko, S. S.; Zybin, E. Yu; Kosyanchuk, V. V.

2018-02-01

In this paper we design a nonparametric method for failures diagnosis in the aircraft control system that uses the measurements of the control signals and the aircraft states only. It doesn’t require a priori information of the aircraft model parameters, training or statistical calculations, and is based on analytical nonparametric one-step-ahead state prediction approach. This makes it possible to predict the behavior of unidentified and failure dynamic systems, to weaken the requirements to control signals, and to reduce the diagnostic time and problem complexity.

Unhealthy health care costs.

PubMed

Shelton, J K; Janosi, J M

1992-02-01

The private sector has implemented many cost containment measures in efforts to control rising health care costs. However, these measures have not controlled costs in the long run, and can be expected not to succeed as long as business cannot control factors within the health care system which affect costs. Controlling private sector health care costs requires constraints on cost shifting which necessitates a unified financing system with expenditure limits. A unified financing system will involve a partnership between the public and private sectors.

Noncontact conductivity and dielectric measurement for high throughput roll-to-roll nanomanufacturing

NASA Astrophysics Data System (ADS)

Orloff, Nathan D.; Long, Christian J.; Obrzut, Jan; Maillaud, Laurent; Mirri, Francesca; Kole, Thomas P.; McMichael, Robert D.; Pasquali, Matteo; Stranick, Stephan J.; Alexander Liddle, J.

2015-11-01

Advances in roll-to-roll processing of graphene and carbon nanotubes have at last led to the continuous production of high-quality coatings and filaments, ushering in a wave of applications for flexible and wearable electronics, woven fabrics, and wires. These applications often require specific electrical properties, and hence precise control over material micro- and nanostructure. While such control can be achieved, in principle, by closed-loop processing methods, there are relatively few noncontact and nondestructive options for quantifying the electrical properties of materials on a moving web at the speed required in modern nanomanufacturing. Here, we demonstrate a noncontact microwave method for measuring the dielectric constant and conductivity (or geometry for samples of known dielectric properties) of materials in a millisecond. Such measurement times are compatible with current and future industrial needs, enabling real-time materials characterization and in-line control of processing variables without disrupting production.

Noncontact conductivity and dielectric measurement for high throughput roll-to-roll nanomanufacturing

PubMed Central

Orloff, Nathan D.; Long, Christian J.; Obrzut, Jan; Maillaud, Laurent; Mirri, Francesca; Kole, Thomas P.; McMichael, Robert D.; Pasquali, Matteo; Stranick, Stephan J.; Alexander Liddle, J.

2015-01-01

Advances in roll-to-roll processing of graphene and carbon nanotubes have at last led to the continuous production of high-quality coatings and filaments, ushering in a wave of applications for flexible and wearable electronics, woven fabrics, and wires. These applications often require specific electrical properties, and hence precise control over material micro- and nanostructure. While such control can be achieved, in principle, by closed-loop processing methods, there are relatively few noncontact and nondestructive options for quantifying the electrical properties of materials on a moving web at the speed required in modern nanomanufacturing. Here, we demonstrate a noncontact microwave method for measuring the dielectric constant and conductivity (or geometry for samples of known dielectric properties) of materials in a millisecond. Such measurement times are compatible with current and future industrial needs, enabling real-time materials characterization and in-line control of processing variables without disrupting production. PMID:26592441

Adaptive weld control for high-integrity welding applications

NASA Technical Reports Server (NTRS)

Powell, Bradley W.

1993-01-01

An advanced adaptive control weld system for high-integrity welding applications is presented. The system consists of a state-of-the-art weld control subsystem, motion control subsystem, and sensor subsystem which closes the loop on the process. The adaptive control subsystem (ACS), which is required to totally close the loop on weld process control, consists of a multiprocessor system, data acquisition hardware, and three welding sensors which provide measurements from all areas around the torch in real time. The ACS acquires all 'measurables' and feeds offset trims back into the weld control and motion control subsystems to modify the 'controllables' in order to maintain a previously defined weld quality.

Chapter 19: HVAC Controls (DDC/EMS/BAS) Evaluation Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurnik, Charles W.; Romberger, Jeff

The HVAC Controls Evaluation Protocol is designed to address evaluation issues for direct digital controls/energy management systems/building automation systems (DDC/EMS/BAS) that are installed to control heating, ventilation, and air-conditioning (HVAC) equipment in commercial and institutional buildings. (This chapter refers to the DDC/EMS/BAS measure as HVAC controls.) This protocol may also be applicable to industrial facilities such as clean rooms and labs, which have either significant HVAC equipment or spaces requiring special environmental conditions.

Current Source Based on H-Bridge Inverter with Output LCL Filter

NASA Astrophysics Data System (ADS)

Blahnik, Vojtech; Talla, Jakub; Peroutka, Zdenek

2015-09-01

The paper deals with a control of current source with an LCL output filter. The controlled current source is realized as a single-phase inverter and output LCL filter provides low ripple of output current. However, systems incorporating LCL filters require more complex control strategies and there are several interesting approaches to the control of this type of converter. This paper presents the inverter control algorithm, which combines model based control with a direct current control based on resonant controllers and single-phase vector control. The primary goal is to reduce the current ripple and distortion under required limits and provides fast and precise control of output current. The proposed control technique is verified by measurements on the laboratory model.

Visual processing in reading disorders and attention-deficit/hyperactivity disorder and its contribution to basic reading ability

PubMed Central

Kibby, Michelle Y.; Dyer, Sarah M.; Vadnais, Sarah A.; Jagger, Audreyana C.; Casher, Gabriel A.; Stacy, Maria

2015-01-01

Whether visual processing deficits are common in reading disorders (RD), and related to reading ability in general, has been debated for decades. The type of visual processing affected also is debated, although visual discrimination and short-term memory (STM) may be more commonly related to reading ability. Reading disorders are frequently comorbid with ADHD, and children with ADHD often have subclinical reading problems. Hence, children with ADHD were used as a comparison group in this study. ADHD and RD may be dissociated in terms of visual processing. Whereas RD may be associated with deficits in visual discrimination and STM for order, ADHD is associated with deficits in visual-spatial processing. Thus, we hypothesized that children with RD would perform worse than controls and children with ADHD only on a measure of visual discrimination and a measure of visual STM that requires memory for order. We expected all groups would perform comparably on the measure of visual STM that does not require sequential processing. We found children with RD or ADHD were commensurate to controls on measures of visual discrimination and visual STM that do not require sequential processing. In contrast, both RD groups (RD, RD/ADHD) performed worse than controls on the measure of visual STM that requires memory for order, and children with comorbid RD/ADHD performed worse than those with ADHD. In addition, of the three visual measures, only sequential visual STM predicted reading ability. Hence, our findings suggest there is a deficit in visual sequential STM that is specific to RD and is related to basic reading ability. The source of this deficit is worthy of further research, but it may include both reduced memory for order and poorer verbal mediation. PMID:26579020

Visual processing in reading disorders and attention-deficit/hyperactivity disorder and its contribution to basic reading ability.

PubMed

Kibby, Michelle Y; Dyer, Sarah M; Vadnais, Sarah A; Jagger, Audreyana C; Casher, Gabriel A; Stacy, Maria

2015-01-01

Whether visual processing deficits are common in reading disorders (RD), and related to reading ability in general, has been debated for decades. The type of visual processing affected also is debated, although visual discrimination and short-term memory (STM) may be more commonly related to reading ability. Reading disorders are frequently comorbid with ADHD, and children with ADHD often have subclinical reading problems. Hence, children with ADHD were used as a comparison group in this study. ADHD and RD may be dissociated in terms of visual processing. Whereas RD may be associated with deficits in visual discrimination and STM for order, ADHD is associated with deficits in visual-spatial processing. Thus, we hypothesized that children with RD would perform worse than controls and children with ADHD only on a measure of visual discrimination and a measure of visual STM that requires memory for order. We expected all groups would perform comparably on the measure of visual STM that does not require sequential processing. We found children with RD or ADHD were commensurate to controls on measures of visual discrimination and visual STM that do not require sequential processing. In contrast, both RD groups (RD, RD/ADHD) performed worse than controls on the measure of visual STM that requires memory for order, and children with comorbid RD/ADHD performed worse than those with ADHD. In addition, of the three visual measures, only sequential visual STM predicted reading ability. Hence, our findings suggest there is a deficit in visual sequential STM that is specific to RD and is related to basic reading ability. The source of this deficit is worthy of further research, but it may include both reduced memory for order and poorer verbal mediation.

Evaluation of effectiveness of combined sewer overflow control measures by operational data.

PubMed

Schroeder, K; Riechel, M; Matzinger, A; Rouault, P; Sonnenberg, H; Pawlowsky-Reusing, E; Gnirss, R

2011-01-01

The effect of combined sewer overflow (CSO) control measures should be validated during operation based on monitoring of CSO activity and subsequent comparison with (legal) requirements. However, most CSO monitoring programs have been started only recently and therefore no long-term data is available for reliable efficiency control. A method is proposed that focuses on rainfall data for evaluating the effectiveness of CSO control measures. It is applicable if a sufficient time-series of rainfall data and a limited set of data on CSO discharges are available. The method is demonstrated for four catchments of the Berlin combined sewer system. The analysis of the 2000-2007 data shows the effect of CSO control measures, such as activation of in-pipe storage capacities within the Berlin system. The catchment, where measures are fully implemented shows less than 40% of the CSO activity of those catchments, where measures have not yet or not yet completely been realised.

10 CFR 75.23 - Operating records.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Accounting and Control for Facilities § 75.23 Operating records. The operating records required by § 75.21... to control the quality of measurements, and the derived estimates of random and systematic error; (c...

Novel sensors to enable closed-loop active clearance control in gas turbine engines

NASA Astrophysics Data System (ADS)

Geisheimer, Jonathan; Holst, Tom

2014-06-01

Active clearance control within the turbine section of gas turbine engines presents and opportunity within aerospace and industrial applications to improve operating efficiencies and the life of downstream components. Open loop clearance control is currently employed during the development of all new large core aerospace engines; however, the ability to measure the gap between the blades and the case and close down the clearance further presents as opportunity to gain even greater efficiencies. The turbine area is one of the harshest environments for long term placement of a sensor in addition to the extreme accuracy requirements required to enable closed loop clearance control. This paper gives an overview of the challenges of clearance measurements within the turbine as well as discusses the latest developments of a microwave sensor designed for this application.

Combustion process science and technology

NASA Technical Reports Server (NTRS)

Hale, Robert R.

1989-01-01

An important and substantial area of technical work in which noncontact temperature measurement (NCTM) is desired is that involving combustion process research. In the planning for this workshop, it was hoped that W. Serignano would provide a briefing regarding the experimental requirements for thermal measurements to support such research. The particular features of thermal measurement requirements included those describing the timeline for combustion experiments, the requirements for thermal control and diagnostics of temperature and other related thermal measurements and the criticality to the involved science to parametric features of measurement capability including precision, repeatability, stability, and resolution. In addition, it was hoped that definitions could be provided which characterize the needs for concurrent imaging as it relates to science observations during the conduct of experimentation.

A whole process quality control system for energy measuring instruments inspection based on IOT technology

NASA Astrophysics Data System (ADS)

Yin, Bo; Liu, Li; Wang, Jiahan; Li, Xiran; Liu, Zhenbo; Li, Dewei; Wang, Jun; Liu, Lu; Wu, Jun; Xu, Tingting; Cui, He

2017-10-01

Electric energy measurement as a basic work, an accurate measurements play a vital role for the economic interests of both parties of power supply, the standardized management of the measurement laboratory at all levels is a direct factor that directly affects the fairness of measurement. Currently, the management of metering laboratories generally uses one-dimensional bar code as the recognition object, advances the testing process by manual management, most of the test data requires human input to generate reports. There are many problems and potential risks in this process: Data cannot be saved completely, cannot trace the status of inspection, the inspection process isn't completely controllable and so on. For the provincial metrology center's actual requirements of the whole process management for the performance test of the power measuring appliances, using of large-capacity RF tags as a process management information media, we developed a set of general measurement experiment management system, formulated a standardized full performance test process, improved the raw data recording mode of experimental process, developed a storehouse automatic inventory device, established a strict test sample transfer and storage system, ensured that all the raw data of the inspection can be traced back, achieved full life-cycle control of the sample, significantly improved the quality control level and the effectiveness of inspection work.

Optimum aerobic volume control based on continuous in-line oxygen uptake monitoring.

PubMed

Svardal, K; Lindtner, S; Winkler, S

2003-01-01

Dynamic adaptation of the aerated volume to changing load conditions is essential to maximise the nitrogen removal performance and to minimise energy consumption. A control strategy is presented which provides optimum aerobic volume control (OAV-control concept) based on continuous in-line oxygen uptake monitoring. For ammonium concentrations below 1 mg/l the oxygen uptake rate shows a strong and almost linear dependency on the ammonium concentration. Therefore, the oxygen uptake rate is an ideal indicator for the nitrification performance in activated sludge systems. The OAV-control concept provides dynamic variation of the minimum aerobic volume required for complete nitrification and therefore maximises the denitrification performance. In-line oxygen uptake monitoring is carried out by controlling the oxygen concentration in a continuous aerated zone of the aeration tank and measuring the total air flow to the aeration tank. The total air flow to the aeration tank is directly proportional to the current oxygen uptake rate and can therefore be used as an indicator for the required aerobic volume. The instrumentation requirements for installation of the OAV-control are relatively low, oxygen sensors in the aeration tank and an on-line air flow measurement are needed. This enables individual control of aeration tanks operated in parallel at low investment costs. The OAV-control concept is installed at the WWTP Linz-Asten (1 Mio PE) and shows very good results. Full scale results are presented.

Studies and research concerning BNFP: computerized nuclear materials control and accounting system development evaluation report, FY 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, J M; Ehinger, M H; Joseph, C

1978-10-01

Development work on a computerized system for nuclear materials control and accounting in a nuclear fuel reprocessing plant is described and evaluated. Hardware and software were installed and tested to demonstrate key measurement, measurement control, and accounting requirements at accountability input/output points using natural uranium. The demonstration included a remote data acquisition system which interfaces process and special instrumentation to a cenral processing unit.

Can the reinforcing value of food be measured in bulimia nervosa?

PubMed Central

Schebendach, Janet; Broft, Allegra; Foltin, Richard W.; Walsh, B. Timothy

2013-01-01

Binge eating is a core clinical feature of bulimia nervosa (BN). Enhanced reinforcing value of food may play a role in this behavioral disturbance, but a systematic behavioral assessment of objective measures of the rewarding value of binge eating is lacking. The purpose of this study was to quantify the reinforcing value of food in BN patients as compared with normal controls. A progressive ratio (PR) computerized work task was completed under binge and non-binge instruction. The task consisted of 12 trials. The first trial required 50 keyboard taps to earn one portion of yogurt shake, and subsequent trials required progressive work increments of 200 taps for each additional portion. Completion of all 12 trials required 13,800 taps to earn 2,100 ml of shake. The breakpoint, defined as the largest ratio completed before a participant stopped working, was the measure of reinforcing efficacy. Ten patients and 10 controls completed the experiment. Under binge instruction, patients completed more trials and taps, and had a higher breakpoint than controls. The non-binge instruction yielded opposite findings; compared to controls, patients completed fewer trials and taps, and had a lower breakpoint. These results support the feasibility and potential utility of a PR task to quantify the reinforcing value of food in patients with BN. PMID:23178173

User definition and mission requirements for unmanned airborne platforms, revised

NASA Technical Reports Server (NTRS)

Kuhner, M. B.; Mcdowell, J. R.

1979-01-01

The airborne measurement requirements of the scientific and applications experiment user community were assessed with respect to the suitability of proposed strawman airborne platforms. These platforms provide a spectrum of measurement capabilities supporting associated mission tradeoffs such as payload weight, operating altitude, range, duration, flight profile control, deployment flexibility, quick response, and recoverability. The results of the survey are used to examine whether the development of platforms is warranted and to determine platform system requirements as well as research and technology needs.

Mission Adaptive Uas Capabilities for Earth Science and Resource Assessment

NASA Astrophysics Data System (ADS)

Dunagan, S.; Fladeland, M.; Ippolito, C.; Knudson, M.; Young, Z.

2015-04-01

Unmanned aircraft systems (UAS) are important assets for accessing high risk airspace and incorporate technologies for sensor coordination, onboard processing, tele-communication, unconventional flight control, and ground based monitoring and optimization. These capabilities permit adaptive mission management in the face of complex requirements and chaotic external influences. NASA Ames Research Center has led a number of Earth science remote sensing missions directed at the assessment of natural resources and here we describe two resource mapping problems having mission characteristics requiring a mission adaptive capability extensible to other resource assessment challenges. One example involves the requirement for careful control over solar angle geometry for passive reflectance measurements. This constraint exists when collecting imaging spectroscopy data over vegetation for time series analysis or for the coastal ocean where solar angle combines with sea state to produce surface glint that can obscure the signal. Furthermore, the primary flight control imperative to minimize tracking error should compromise with the requirement to minimize aircraft motion artifacts in the spatial measurement distribution. A second example involves mapping of natural resources in the Earth's crust using precision magnetometry. In this case the vehicle flight path must be oriented to optimize magnetic flux gradients over a spatial domain having continually emerging features, while optimizing the efficiency of the spatial mapping task. These requirements were highlighted in recent Earth Science missions including the OCEANIA mission directed at improving the capability for spectral and radiometric reflectance measurements in the coastal ocean, and the Surprise Valley Mission directed at mapping sub-surface mineral composition and faults, using high-sensitivity magnetometry. This paper reports the development of specific aircraft control approaches to incorporate the unusual and demanding requirements to manage solar angle, aircraft attitude and flight path orientation, and efficient (directly geo-rectified) surface and sub-surface mapping, including the near-time optimization of these sometimes competing requirements.

Online total organic carbon (TOC) monitoring for water and wastewater treatment plants processes and operations optimization

NASA Astrophysics Data System (ADS)

Assmann, Céline; Scott, Amanda; Biller, Dondra

2017-08-01

Organic measurements, such as biological oxygen demand (BOD) and chemical oxygen demand (COD) were developed decades ago in order to measure organics in water. Today, these time-consuming measurements are still used as parameters to check the water treatment quality; however, the time required to generate a result, ranging from hours to days, does not allow COD or BOD to be useful process control parameters - see (1) Standard Method 5210 B; 5-day BOD Test, 1997, and (2) ASTM D1252; COD Test, 2012. Online organic carbon monitoring allows for effective process control because results are generated every few minutes. Though it does not replace BOD or COD measurements still required for compliance reporting, it allows for smart, data-driven and rapid decision-making to improve process control and optimization or meet compliances. Thanks to the smart interpretation of generated data and the capability to now take real-time actions, municipal drinking water and wastewater treatment facility operators can positively impact their OPEX (operational expenditure) efficiencies and their capabilities to meet regulatory requirements. This paper describes how three municipal wastewater and drinking water plants gained process insights, and determined optimization opportunities thanks to the implementation of online total organic carbon (TOC) monitoring.

Brake testing methodology study : driver effects testing

DOT National Transportation Integrated Search

1999-03-01

The National Highway Traffic Safety Administration (NHTSA) is exploring the feasibility of developing brake tests to measure brake system performance of light vehicles. Developing test procedures requires controlling test variability so that measured...

Development and Characterization of a Low-Pressure Calibration System for Hypersonic Wind Tunnels

NASA Technical Reports Server (NTRS)

Green, Del L.; Everhart, Joel L.; Rhode, Matthew N.

2004-01-01

Minimization of uncertainty is essential for accurate ESP measurements at very low free-stream static pressures found in hypersonic wind tunnels. Statistical characterization of environmental error sources requires a well defined and controlled calibration method. A calibration system has been constructed and environmental control software developed to control experimentation to eliminate human induced error sources. The initial stability study of the calibration system shows a high degree of measurement accuracy and precision in temperature and pressure control. Control manometer drift and reference pressure instabilities induce uncertainty into the repeatability of voltage responses measured from the PSI System 8400 between calibrations. Methods of improving repeatability are possible through software programming and further experimentation.

A low-level rf control system for a quarter-wave resonator

NASA Astrophysics Data System (ADS)

Kim, Jongwon; Hwang, Churlkew

2012-06-01

A low-level rf control system was designed and built for an rf deflector, which is a quarter wave resonator, and was designed to deflect a secondary electron beam to measure the bunch length of an ion beam. The deflector has a resonance frequency near 88 MHz, its required phase stability is approximately ±1° and its amplitude stability is less than ±1%. The control system consists of analog input and output components and a digital system based on a field-programmable gate array for signal processing. The system is cost effective, while meeting the stability requirements. Some basic properties of the control system were measured. Then, the capability of the rf control was tested using a mechanical vibrator made of a dielectric rod attached to an audio speaker system, which could induce regulated perturbations in the electric fields of the resonator. The control system was flexible so that its parameters could be easily configured to compensate for the disturbance induced in the resonator.

Value-Based Argumentation for Justifying Compliance

NASA Astrophysics Data System (ADS)

Burgemeestre, Brigitte; Hulstijn, Joris; Tan, Yao-Hua

Compliance is often achieved 'by design' through a coherent system of controls consisting of information systems and procedures . This system-based control requires a new approach to auditing in which companies must demonstrate to the regulator that they are 'in control'. They must determine the relevance of a regulation for their business, justify which set of control measures they have taken to comply with it, and demonstrate that the control measures are operationally effective. In this paper we show how value-based argumentation theory can be applied to the compliance domain. Corporate values motivate the selection of control measures (actions) which aim to fulfill control objectives, i.e. adopted norms (goals). In particular, we show how to formalize the dialogue in which companies justify their compliance decisions to regulators using value-based argumentation. The approach is illustrated by a case study of the safety and security measures adopted in the context of EU customs regulation.

Measurement and Control System Based on Wireless Senor Network for Granary

NASA Astrophysics Data System (ADS)

Song, Jian

A wireless measurement and control system for granary is developed for the sake of overcoming the shortcoming of the wired measurement and control system such as complex wiring and low anti-interference capacity. In this system, Zigbee technology is applied with Zigbee protocol stack development platform by TI, and wireless senor network is used to collect and control the temperature and the humidity. It is composed of the upper PC, central control node based on CC2530, sensor nodes, sensor modules and the executive device. The wireless sensor node is programmed by C language in IAR Embedded Workbench for MCS-51 Evaluation environment. The upper PC control system software is developed based on Visual C++ 6.0 platform. It is shown by experiments that data transmission in the system is accurate and reliable and the error of the temperature and humidity is below 2%, meeting the functional requirements for the granary measurement and control system.

3D laser scanning for quality control and assurance in bridge deck construction.

DOT National Transportation Integrated Search

2014-08-01

The inspection of installations of rebar and other embedded components in bridge deck construction is a tedious : task for eld inspectors, requiring considerable eld time for measurement and verication against code requirement. The verica...

40 CFR 51.124 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., or any form of solid, liquid, or gaseous fuel derived from such material. Fossil-fuel-fired means...) If a State elects to impose control measures on fossil fuel-fired non-EGUs that are boilers or... chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non-EGUs that are boilers...

40 CFR 51.124 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., or any form of solid, liquid, or gaseous fuel derived from such material. Fossil-fuel-fired means...) If a State elects to impose control measures on fossil fuel-fired non-EGUs that are boilers or... chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non-EGUs that are boilers...

40 CFR 51.124 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or any form of solid, liquid, or gaseous fuel derived from such material. Fossil-fuel-fired means...) If a State elects to impose control measures on fossil fuel-fired non-EGUs that are boilers or... chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non-EGUs that are boilers...

40 CFR 51.124 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., or any form of solid, liquid, or gaseous fuel derived from such material. Fossil-fuel-fired means...) If a State elects to impose control measures on fossil fuel-fired non-EGUs that are boilers or... chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non-EGUs that are boilers...

40 CFR 51.124 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., or any form of solid, liquid, or gaseous fuel derived from such material. Fossil-fuel-fired means...) If a State elects to impose control measures on fossil fuel-fired non-EGUs that are boilers or... chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non-EGUs that are boilers...

Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test

NASA Technical Reports Server (NTRS)

Lenahan, Keven C.; Schatzman, David M.; Wilson, Jacob Samuel

2013-01-01

Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.

30 CFR 780.18 - Reclamation plan: General requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... appropriate, and pest and disease control measures, if any; and (vi) Measures proposed to be used to determine... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 784.13 - Reclamation plan: General requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... appropriate, and pest and disease control measures, if any; (vi) Measures proposed to be used to determine the... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 784.13 - Reclamation plan: General requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... appropriate, and pest and disease control measures, if any; (vi) Measures proposed to be used to determine the... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 784.13 - Reclamation plan: General requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... appropriate, and pest and disease control measures, if any; (vi) Measures proposed to be used to determine the... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 780.18 - Reclamation plan: General requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... appropriate, and pest and disease control measures, if any; and (vi) Measures proposed to be used to determine... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 780.18 - Reclamation plan: General requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... appropriate, and pest and disease control measures, if any; and (vi) Measures proposed to be used to determine... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 780.18 - Reclamation plan: General requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... appropriate, and pest and disease control measures, if any; and (vi) Measures proposed to be used to determine... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 780.18 - Reclamation plan: General requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... appropriate, and pest and disease control measures, if any; and (vi) Measures proposed to be used to determine... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 784.13 - Reclamation plan: General requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... appropriate, and pest and disease control measures, if any; (vi) Measures proposed to be used to determine the... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

30 CFR 784.13 - Reclamation plan: General requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... appropriate, and pest and disease control measures, if any; (vi) Measures proposed to be used to determine the... chemical and physical analyses, field-site trials, or greenhouse tests if determined to be necessary or...

40 CFR Appendix D to Part 60 - Required Emission Inventory Information

Code of Federal Regulations, 2010 CFR

2010-07-01

... one device operates in series. The method of control efficiency determination shall be indicated (e.g., design efficiency, measured efficiency, estimated efficiency). (iii) Annual average control efficiency, in percent, taking into account control equipment down time. This shall be a combined efficiency when...

40 CFR Appendix D to Part 60 - Required Emission Inventory Information

Code of Federal Regulations, 2011 CFR

2011-07-01

... one device operates in series. The method of control efficiency determination shall be indicated (e.g., design efficiency, measured efficiency, estimated efficiency). (iii) Annual average control efficiency, in percent, taking into account control equipment down time. This shall be a combined efficiency when...

40 CFR Appendix D to Part 60 - Required Emission Inventory Information

Code of Federal Regulations, 2012 CFR

2012-07-01

... one device operates in series. The method of control efficiency determination shall be indicated (e.g., design efficiency, measured efficiency, estimated efficiency). (iii) Annual average control efficiency, in percent, taking into account control equipment down time. This shall be a combined efficiency when...

40 CFR Appendix D to Part 60 - Required Emission Inventory Information

Code of Federal Regulations, 2013 CFR

2013-07-01

... one device operates in series. The method of control efficiency determination shall be indicated (e.g., design efficiency, measured efficiency, estimated efficiency). (iii) Annual average control efficiency, in percent, taking into account control equipment down time. This shall be a combined efficiency when...

40 CFR Appendix D to Part 60 - Required Emission Inventory Information

Code of Federal Regulations, 2014 CFR

2014-07-01

... one device operates in series. The method of control efficiency determination shall be indicated (e.g., design efficiency, measured efficiency, estimated efficiency). (iii) Annual average control efficiency, in percent, taking into account control equipment down time. This shall be a combined efficiency when...

76 FR 74014 - Approval and Promulgation of Implementation Plans; Illinois; Volatile Organic Compound Emission...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-30

... Promulgation of Implementation Plans; Illinois; Volatile Organic Compound Emission Control Measures for Chicago... Act's (the Act) requirement that States revise their SIPs to include reasonably available control... rules are approvable because they are consistent with the Control Technique Guideline (CTG) documents...

33 CFR 104.265 - Security measures for access control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Security measures for access... SECURITY MARITIME SECURITY MARITIME SECURITY: VESSELS Vessel Security Requirements § 104.265 Security... security measures to: (1) Deter the unauthorized introduction of dangerous substances and devices...

Characterizing SWCNT Dispersion in Polymer Composites

NASA Technical Reports Server (NTRS)

Lillehei, Peter T.; Kim, Jae-Woo; Gibbons, Luke; Park, Cheol

2007-01-01

The new wave of single wall carbon nanotube (SWCNT) infused composites will yield structurally sound multifunctional nanomaterials. The SWCNT network requires thorough dispersion within the polymer matrix in order to maximize the benefits of the nanomaterial. However, before any nanomaterials can be used in aerospace applications a means of quality assurance and quality control must be certified. Quality control certification requires a means of quantification, however, the measurement protocol mandates a method of seeing the dispersion first. We describe here the new tools that we have developed and implemented to first be able to see carbon nanotubes in polymers and second to measure or quantify the dispersion of the nanotubes.

Oregon Department of Transportation research leader : fall 2008.

DOT National Transportation Integrated Search

2008-01-01

The newsletter includes: : 1) To ensure safe travel through construction work zones, Traffic Control Plans (TCPs) are developed to communicate required traffic control measures to the construction team. The quality of the design and implementation of...

Infection prevention and control.

PubMed

Pegram, Anne; Bloomfield, Jacqueline

2015-03-18

All newly registered graduate nurses are required to have the appropriate knowledge and understanding to perform the skills required for patient care, specifically the competencies identified in the Nursing and Midwifery Council's essential skills clusters. This article focuses on the third essential skills cluster - infection prevention and control. It provides an overview and discussion of the key skills and behaviours that must be demonstrated to meet the standards set by the Nursing and Midwifery Council. In doing so, it considers the key principles of infection prevention and control, including local and national policies, standard infection control precautions, risk assessment, standard isolation measures and asepsis.

Measuring the development of inhibitory control: The challenge of heterotypic continuity

PubMed Central

Petersen, Isaac T.; Hoyniak, Caroline P.; McQuillan, Maureen E.; Bates, John E.; Staples, Angela D.

2016-01-01

Inhibitory control is thought to demonstrate heterotypic continuity, in other words, continuity in its purpose or function but changes in its behavioral manifestation over time. This creates major methodological challenges for studying the development of inhibitory control in childhood including construct validity, developmental appropriateness and sensitivity of measures, and longitudinal factorial invariance. We meta-analyzed 198 studies using measures of inhibitory control, a key aspect of self-regulation, to estimate age ranges of usefulness for each measure. The inhibitory control measures showed limited age ranges of usefulness owing to ceiling/floor effects. Tasks were useful, on average, for a developmental span of less than 3 years. This suggests that measuring inhibitory control over longer spans of development may require use of different measures at different time points, seeking to measure heterotypic continuity. We suggest ways to study the development of inhibitory control, with overlapping measurement in a structural equation modeling framework and tests of longitudinal factorial or measurement invariance. However, as valuable as this would be for the area, we also point out that establishing longitudinal factorial invariance is neither sufficient nor necessary for examining developmental change. Any study of developmental change should be guided by theory and construct validity, aiming toward a better empirical and theoretical approach to the selection and combination of measures. PMID:27346906

Quantifying control effort of biological and technical movements: an information-entropy-based approach.

PubMed

Haeufle, D F B; Günther, M; Wunner, G; Schmitt, S

2014-01-01

In biomechanics and biorobotics, muscles are often associated with reduced movement control effort and simplified control compared to technical actuators. This is based on evidence that the nonlinear muscle properties positively influence movement control. It is, however, open how to quantify the simplicity aspect of control effort and compare it between systems. Physical measures, such as energy consumption, stability, or jerk, have already been applied to compare biological and technical systems. Here a physical measure of control effort based on information entropy is presented. The idea is that control is simpler if a specific movement is generated with less processed sensor information, depending on the control scheme and the physical properties of the systems being compared. By calculating the Shannon information entropy of all sensor signals required for control, an information cost function can be formulated allowing the comparison of models of biological and technical control systems. Exemplarily applied to (bio-)mechanical models of hopping, the method reveals that the required information for generating hopping with a muscle driven by a simple reflex control scheme is only I=32 bits versus I=660 bits with a DC motor and a proportional differential controller. This approach to quantifying control effort captures the simplicity of a control scheme and can be used to compare completely different actuators and control approaches.

Using VAPEPS for noise control on Space Station Freedom

NASA Technical Reports Server (NTRS)

Badilla, Gloria; Bergen, Thomas; Scharton, Terry

1991-01-01

Noise environmental control is an important design consideration for Space Station Freedom (SSF), both for crew safety and productivity. Acoustic noise requirements are established to eliminate fatigue and potential hearing loss by crew members from long-term exposure and to facilitate speech communication. VAPEPS (VibroAcoustic Payload Environment Prediction System) is currently being applied to SSF for prediction of the on-orbit noise and vibration environments induced in the 50 to 10,000 Hz frequency range. Various sources such as fans, pumps, centrifuges, exercise equipment, and other mechanical devices are used in the analysis. The predictions will be used in design tradeoff studies and to provide confidence that requirements will be met. Preliminary predictions show that the required levels will be exceeded unless substantial noise control measures are incorporated in the SSF design. Predicted levels for an SSF design without acoustic control treatments exceed requirements by 25 dB in some one-third octave frequency bands.

49 CFR Appendix F to Part 229 - Recommended Practices for Design and Safety Analysis

Code of Federal Regulations, 2014 CFR

2014-10-01

... expected order of use; (v) Group similar controls together; (vi) Design for high stimulus-response compatibility (geometric and conceptual); (vii) Design safety-critical controls to require more than one... description of all backup methods of operation; and (s) The configuration/revision control measures designed...

49 CFR Appendix F to Part 229 - Recommended Practices for Design and Safety Analysis

Code of Federal Regulations, 2012 CFR

2012-10-01

... expected order of use; (v) Group similar controls together; (vi) Design for high stimulus-response compatibility (geometric and conceptual); (vii) Design safety-critical controls to require more than one... description of all backup methods of operation; and (s) The configuration/revision control measures designed...

49 CFR Appendix F to Part 229 - Recommended Practices for Design and Safety Analysis

Code of Federal Regulations, 2013 CFR

2013-10-01

... expected order of use; (v) Group similar controls together; (vi) Design for high stimulus-response compatibility (geometric and conceptual); (vii) Design safety-critical controls to require more than one... description of all backup methods of operation; and (s) The configuration/revision control measures designed...

40 CFR 52.726 - Control strategy: Ozone.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Transportation Study: “Transportation Control Measures Contribution to the Post-1996 Rate-Of-Progress State...) [Reserved] (2) The State conducts a study to demonstrate that the 75 percent overall control efficiency requirement in Rule 205(n) represents RACT, submits the results of the study to USEPA, and submits any...

40 CFR 52.726 - Control strategy: Ozone.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Transportation Study: “Transportation Control Measures Contribution to the Post-1996 Rate-Of-Progress State...) [Reserved] (2) The State conducts a study to demonstrate that the 75 percent overall control efficiency requirement in Rule 205(n) represents RACT, submits the results of the study to USEPA, and submits any...

40 CFR 141.87 - Monitoring requirements for water quality parameters.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (c) Monitoring after installation of corrosion control. Any large system which installs optimal corrosion control treatment pursuant to § 141.81(d)(4) shall measure the water quality parameters at the...)(i). Any small or medium-size system which installs optimal corrosion control treatment shall conduct...

40 CFR 141.87 - Monitoring requirements for water quality parameters.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (c) Monitoring after installation of corrosion control. Any large system which installs optimal corrosion control treatment pursuant to § 141.81(d)(4) shall measure the water quality parameters at the...)(i). Any small or medium-size system which installs optimal corrosion control treatment shall conduct...

40 CFR 141.87 - Monitoring requirements for water quality parameters.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (c) Monitoring after installation of corrosion control. Any large system which installs optimal corrosion control treatment pursuant to § 141.81(d)(4) shall measure the water quality parameters at the...)(i). Any small or medium-size system which installs optimal corrosion control treatment shall conduct...

40 CFR 141.87 - Monitoring requirements for water quality parameters.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (c) Monitoring after installation of corrosion control. Any large system which installs optimal corrosion control treatment pursuant to § 141.81(d)(4) shall measure the water quality parameters at the...)(i). Any small or medium-size system which installs optimal corrosion control treatment shall conduct...

40 CFR 141.87 - Monitoring requirements for water quality parameters.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (c) Monitoring after installation of corrosion control. Any large system which installs optimal corrosion control treatment pursuant to § 141.81(d)(4) shall measure the water quality parameters at the...)(i). Any small or medium-size system which installs optimal corrosion control treatment shall conduct...

20171015 - Generating Exposure-Relevant Measurement Data for Potential Use in Support of TSCA Requirements (ISES)

EPA Science Inventory

The EPA Office of Research and Development (ORD) has a number of ongoing projects which generate exposure measurements. These data may inform ongoing implementation of the amended Toxic Substances Control Act (TSCA). Exposure measurements include physical-chemical property inform...

Design of a temperature measurement and feedback control system based on an improved magnetic nanoparticle thermometer

NASA Astrophysics Data System (ADS)

Du, Zhongzhou; Sun, Yi; Liu, Jie; Su, Rijian; Yang, Ming; Li, Nana; Gan, Yong; Ye, Na

2018-04-01

Magnetic fluid hyperthermia, as a novel cancer treatment, requires precise temperature control at 315 K-319 K (42 °C-46 °C). However, the traditional temperature measurement method cannot obtain the real-time temperature in vivo, resulting in a lack of temperature feedback during the heating process. In this study, the feasibility of temperature measurement and feedback control using magnetic nanoparticles is proposed and demonstrated. This technique could be applied in hyperthermia. Specifically, the triangular-wave temperature measurement method is improved by reconstructing the original magnetization response of magnetic nanoparticles based on a digital phase-sensitive detection algorithm. The standard deviation of the temperature in the magnetic nanoparticle thermometer is about 0.1256 K. In experiments, the temperature fluctuation of the temperature measurement and feedback control system using magnetic nanoparticles is less than 0.5 K at the expected temperature of 315 K. This shows the feasibility of the temperature measurement method for temperature control. The method provides a new solution for temperature measurement and feedback control in hyperthermia.

Tuberculosis and infection control.

PubMed

Karim, Kelvin

Against a background of rising tuberculosis (TB) rates, increasing incidence of TB and human immunodeficiency virus (HIV) co-infection, coupled with the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB), the need for effective TB infection control has never been more vital (World Health Organization (WHO), 2009). TB infection control has been defined as 'a combination of measures aimed at minimizing the risk of TB transmission within populations' (WHO, 2009: p.ix). Health professionals are frequently confused about appropriate infection control measures when caring for patients affected by infectious respiratory tuberculosis (Mohandas and Cunniffe, 2009). This article aims to address the key infection control measures required to optimize patient care and reduce the risk of TB transmission within hospital and community settings.

Command and Control Systems Requirements Analysis. Volume 2. Measuring C2 Effectiveness with Decision Probability

DTIC Science & Technology

1990-09-01

MEASURING C2 EFFECTIVENESS WUIlT DECISION PROBABILITY SEPTEMBER 1990 TABLE OF CONTENTS 1.0 IN T R O D U CTIIO N...i ’i | " i | , TABLE OF CONTENTS (Continued) Ra. 5.0 EXPRESSING REQUIREMENTS WITH PROBABILITY .................................... 15 5.1...gaitrering and maintaining the data needed, and complfeting and reviewing the coiierction of Intoirmallon Send continnts regarding MAr burden asilmate o

40 CFR 51.123 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2014 CFR

2014-07-01

... the source: (i) For EGUs and for fossil-fuel-fired non-EGUs that are boilers or combustion turbines... sources in the State. (ii) If a State elects to impose control measures on fossil fuel-fired non-EGUs that... part 75 of this chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non...

40 CFR 51.123 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2011 CFR

2011-07-01

... the source: (i) For EGUs and for fossil-fuel-fired non-EGUs that are boilers or combustion turbines... sources in the State. (ii) If a State elects to impose control measures on fossil fuel-fired non-EGUs that... part 75 of this chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non...

40 CFR 51.123 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2012 CFR

2012-07-01

... the source: (i) For EGUs and for fossil-fuel-fired non-EGUs that are boilers or combustion turbines... sources in the State. (ii) If a State elects to impose control measures on fossil fuel-fired non-EGUs that... part 75 of this chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non...

40 CFR 51.123 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2010 CFR

2010-07-01

... the source: (i) For EGUs and for fossil-fuel-fired non-EGUs that are boilers or combustion turbines... sources in the State. (ii) If a State elects to impose control measures on fossil fuel-fired non-EGUs that... part 75 of this chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non...

40 CFR 51.123 - Findings and requirements for submission of State implementation plan revisions relating to...

Code of Federal Regulations, 2013 CFR

2013-07-01

... the source: (i) For EGUs and for fossil-fuel-fired non-EGUs that are boilers or combustion turbines... sources in the State. (ii) If a State elects to impose control measures on fossil fuel-fired non-EGUs that... part 75 of this chapter. (ii) If the SIP revision contains measures to control fossil fuel-fired non...

Spill Prevention and Countermeasures Plan

DTIC Science & Technology

1984-08-01

THE DISCHARGE OF OiIL AND HAZARDOUS SUBSTANCES AT RMA. THE SPCC PLAN IDENTIFIES POTENTIAL SOURCES OF OIL AND HAZARDOUS SUBSTANCES AND THE MEASURES...Control and Countermeasure (SPCC) Plan is to prevent and control the discharge of oil and hazardous sub- stances at Rocky Mountain Arsenal (RYA). The...SPCC Plan identifies potential sources of oil and hazardous substances and the measures required to prevent an accidental discharge resulting from

Detection of gas leakage

DOEpatents

Thornberg, Steven [Peralta, NM; Brown, Jason [Albuquerque, NM

2012-06-19

A method of detecting leaks and measuring volumes as well as an apparatus, the Power-free Pump Module (PPM), that is a self-contained leak test and volume measurement apparatus that requires no external sources of electrical power during leak testing or volume measurement, where the invention is a portable, pneumatically-controlled instrument capable of generating a vacuum, calibrating volumes, and performing quantitative leak tests on a closed test system or device, all without the use of alternating current (AC) power. Capabilities include the ability is to provide a modest vacuum (less than 10 Torr), perform a pressure rise leak test, measure the gas's absolute pressure, and perform volume measurements. All operations are performed through a simple rotary control valve which controls pneumatically-operated manifold valves.

Detection of gas leakage

DOEpatents

Thornberg, Steven M; Brown, Jason

2015-02-17

A method of detecting leaks and measuring volumes as well as a device, the Power-free Pump Module (PPM), provides a self-contained leak test and volume measurement apparatus that requires no external sources of electrical power during leak testing or volume measurement. The PPM is a portable, pneumatically-controlled instrument capable of generating a vacuum, calibrating volumes, and performing quantitative leak tests on a closed test system or device, all without the use of alternating current (AC) power. Capabilities include the ability is to provide a modest vacuum (less than 10 Torr) using a venturi pump, perform a pressure rise leak test, measure the gas's absolute pressure, and perform volume measurements. All operations are performed through a simple rotary control valve which controls pneumatically-operated manifold valves.

Can the reinforcing value of food be measured in bulimia nervosa?

PubMed

Schebendach, Janet; Broft, Allegra; Foltin, Richard W; Walsh, B Timothy

2013-03-01

Binge eating is a core clinical feature of bulimia nervosa (BN). Enhanced reinforcing value of food may play a role in this behavioral disturbance, but a systematic behavioral assessment of objective measures of the rewarding value of binge eating is lacking. The purpose of this study was to quantify the reinforcing value of food in BN patients as compared with normal controls. A progressive ratio (PR) computerized work task was completed under binge and non-binge instruction. The task consisted of 12 trials. The first trial required 50 keyboard taps to earn one portion of yogurt shake, and subsequent trials required progressive work increments of 200 taps for each additional portion. Completion of all 12 trials required 13,800 taps to earn 2100ml of shake. The breakpoint, defined as the largest ratio completed before a participant stopped working, was the measure of reinforcing efficacy. Ten patients and 10 controls completed the experiment. Under binge instruction, patients completed more trials and taps, and had a higher breakpoint than controls. The non-binge instruction yielded opposite findings; compared to controls, patients completed fewer trials and taps, and had a lower breakpoint. These results support the feasibility and potential utility of a PR task to quantify the reinforcing value of food in patients with BN. Copyright © 2012 Elsevier Ltd. All rights reserved.

Instrumentation: Software-Driven Instrumentation: The New Wave.

ERIC Educational Resources Information Center

Salit, M. L.; Parsons, M. L.

1985-01-01

Software-driven instrumentation makes measurements that demand a computer as an integral part of either control, data acquisition, or data reduction. The structure of such instrumentation, hardware requirements, and software requirements are discussed. Examples of software-driven instrumentation (such as wavelength-modulated continuum source…

40 CFR 98.284 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... accounting purposes including direct measurement weighing the petroleum coke fed into your process (by belt... used to ensure the accuracy of monthly petroleum coke consumption measurements. (c) For CO2 process... quality assurance and quality control of the supplier data, you must conduct an annual measurement of the...

On Cyber Warfare Command and Control Systems

DTIC Science & Technology

2004-06-01

longer adequate to rely solely on the now traditional defense-in-depth strategy. We must recognize that we are engaged in a form of warfare, cyber warfare , and... warfare . This causes security devices to be used ineffectively and responses to be untimely. Cyber warfare then becomes a one-sided battle where the... cyber warfare strategy and tactics requires a cyber warfare command and control system. Responses to cyber attacks do not require offensive measures

Application of advanced diffraction based optical metrology overlay capabilities for high-volume manufacturing

NASA Astrophysics Data System (ADS)

Chen, Kai-Hsiung; Huang, Guo-Tsai; Hsieh, Hung-Chih; Ni, Wei-Feng; Chuang, S. M.; Chuang, T. K.; Ke, Chih-Ming; Huang, Jacky; Rao, Shiuan-An; Cumurcu Gysen, Aysegul; d'Alfonso, Maxime; Yueh, Jenny; Izikson, Pavel; Soco, Aileen; Wu, Jon; Nooitgedagt, Tjitte; Ottens, Jeroen; Kim, Yong Ho; Ebert, Martin

2017-03-01

On-product overlay requirements are becoming more challenging with every next technology node due to the continued decrease of the device dimensions and process tolerances. Therefore, current and future technology nodes require demanding metrology capabilities such as target designs that are robust towards process variations and high overlay measurement density (e.g. for higher order process corrections) to enable advanced process control solutions. The impact of advanced control solutions based on YieldStar overlay data is being presented in this paper. Multi patterning techniques are applied for critical layers and leading to additional overlay measurement demands. The use of 1D process steps results in the need of overlay measurements relative to more than one layer. Dealing with the increased number of overlay measurements while keeping the high measurement density and metrology accuracy at the same time presents a challenge for high volume manufacturing (HVM). These challenges are addressed by the capability to measure multi-layer targets with the recently introduced YieldStar metrology tool, YS350. On-product overlay results of such multi-layers and standard targets are presented including measurement stability performance.

Measuring Software Product Quality: The ISO 25000 Series and CMMI

DTIC Science & Technology

2004-06-14

performance objectives” covers objectives and requirements for product quality, service quality , and process performance. Process performance objectives...such that product quality, service quality , and process performance attributes are measurable and controlled throughout the project (internal and

78 FR 17781 - Transportation Worker Identification Credential (TWIC)-Reader Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-22

...In this Notice of Proposed Rulemaking (NPRM), the Coast Guard proposes to require owners and operators of certain vessels and facilities regulated by the Coast Guard to use electronic readers designed to work with the Transportation Worker Identification Credential (TWIC) as an access control measure. This NPRM also proposes additional requirements associated with electronic TWIC readers, including recordkeeping requirements for those owners and operators required to use an electronic TWIC reader, and security plan amendments to incorporate TWIC requirements. The TWIC program, including the proposed TWIC reader requirements in this rule, is an important component of the Coast Guard's multi-layered system of access control requirements and other measures designed to enhance maritime security. This rulemaking action, once final, would build upon existing Coast Guard regulations designed to ensure that only individuals who hold a TWIC are granted unescorted access to secure areas at those locations. The Coast Guard has already promulgated regulations pursuant to the Maritime Transportation Security Act of 2002 (MTSA) that require mariners and other individuals to obtain a TWIC and present it for inspection by security personnel prior to gaining access to such secure areas. By requiring certain vessels and facilities to perform TWIC inspections using electronic TWIC readers, this rulemaking would further enhance security at those locations. This rulemaking would also implement the Security and Accountability For Every Port Act of 2006 electronic TWIC reader requirements.

Oculomotor Cognitive Control Abnormalities in Australian Rules Football Players with a History of Concussion.

PubMed

Clough, Meaghan; Mutimer, Steven; Wright, David K; Tsang, Adrian; Costello, Daniel M; Gardner, Andrew J; Stanwell, Peter; Mychasiuk, Richelle; Sun, Mujun; Brady, Rhys D; McDonald, Stuart J; Webster, Kyria M; Johnstone, Maddison R; Semple, Bridgette D; Agoston, Denes V; White, Owen B; Frayne, Richard; Fielding, Joanne; O'Brien, Terence J; Shultz, Sandy R

2018-03-01

This study used oculomotor, cognitive, and multi-modal magnetic resonance imaging (MRI) measures to assess for neurological abnormalities in current asymptomatic amateur Australian rules footballers (i.e., Australia's most participated collision sport) with a history of sports-related concussion (SRC). Participants were 15 male amateur Australian rules football players with a history of SRC greater than 6 months previously, and 15 sex-, age-, and education-matched athlete control subjects that had no history of neurotrauma or participation in collision sports. Participants completed a clinical interview, neuropsychological measures, and oculomotor measures of cognitive control. MRI investigation involved structural imaging, as well as diffusion tensor imaging and resting-state functional MRI sequences. Despite no group differences on conventional neuropsychological tests and multi-modal MRI measures, Australian rules football players with a history of SRC performed significantly worse on an oculomotor switch task: a measure of cognitive control that interleaves the response of looking towards a target (i.e., a prosaccade) with the response of looking away from a target (i.e., an antisaccade). Specifically, Australian footballers performed significantly shorter latency prosaccades and found changing from an antisaccade trial to a prosaccade trial (switch cost) significantly more difficult than control subjects. Poorer switch cost was related to poorer performance on a number of neuropsychological measures of inhibitory control. Further, when comparing performance on the cognitively more demanding switch task with performance on simpler, antisaccade/prosaccades tasks which require a single response, Australian footballers demonstrated a susceptibility to increased cognitive load, compared to the control group who were unaffected. These initial results suggest that current asymptomatic amateur Australian rules football players with a history of SRC may have persisting, subtle, cognitive changes, which are demonstrable on oculomotor cognitive measures. Future studies are required in order to further elucidate the full nature and clinical relevance of these findings.

Validity of the Instrumented Push and Release Test to Quantify Postural Responses in Persons With Multiple Sclerosis.

PubMed

El-Gohary, Mahmoud; Peterson, Daniel; Gera, Geetanjali; Horak, Fay B; Huisinga, Jessie M

2017-07-01

To test the validity of wearable inertial sensors to provide objective measures of postural stepping responses to the push and release clinical test in people with multiple sclerosis. Cross-sectional study. University medical center balance disorder laboratory. Total sample N=73; persons with multiple sclerosis (PwMS) n=52; healthy controls n=21. Stepping latency, time and number of steps required to reach stability, and initial step length were calculated using 3 inertial measurement units placed on participants' lumbar spine and feet. Correlations between inertial sensor measures and measures obtained from the laboratory-based systems were moderate to strong and statistically significant for all variables: time to release (r=.992), latency (r=.655), time to stability (r=.847), time of first heel strike (r=.665), number of steps (r=.825), and first step length (r=.592). Compared with healthy controls, PwMS demonstrated a longer time to stability and required a larger number of steps to reach stability. The instrumented push and release test is a valid measure of postural responses in PwMS and could be used as a clinical outcome measures for patient care decisions or for clinical trials aimed at improving postural control in PwMS. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

16 CFR 1633.3 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... FLAMMABILITY (OPEN FLAME) OF MATTRESS SETS The Standard § 1633.3 General requirements. (a) Summary of test method. The test method set forth in § 1633.7 measures the flammability (fire test response... allowing it to burn freely under well-ventilated, controlled environmental conditions. The flaming ignition...

43 CFR 6304.22 - What special provisions apply to control of fire, insects, and diseases?

Code of Federal Regulations, 2011 CFR

2011-10-01

... of fire, insects, and diseases? 6304.22 Section 6304.22 Public Lands: Interior Regulations Relating... apply to control of fire, insects, and diseases? BLM may prescribe measures to control fire, noxious weeds, non-native invasive plants, insects, and diseases. BLM may require restoration concurrent with or...

43 CFR 6304.22 - What special provisions apply to control of fire, insects, and diseases?

Code of Federal Regulations, 2013 CFR

2013-10-01

... of fire, insects, and diseases? 6304.22 Section 6304.22 Public Lands: Interior Regulations Relating... apply to control of fire, insects, and diseases? BLM may prescribe measures to control fire, noxious weeds, non-native invasive plants, insects, and diseases. BLM may require restoration concurrent with or...

43 CFR 6304.22 - What special provisions apply to control of fire, insects, and diseases?

Code of Federal Regulations, 2014 CFR

2014-10-01

... of fire, insects, and diseases? 6304.22 Section 6304.22 Public Lands: Interior Regulations Relating... apply to control of fire, insects, and diseases? BLM may prescribe measures to control fire, noxious weeds, non-native invasive plants, insects, and diseases. BLM may require restoration concurrent with or...

43 CFR 6304.22 - What special provisions apply to control of fire, insects, and diseases?

Code of Federal Regulations, 2012 CFR

2012-10-01

... of fire, insects, and diseases? 6304.22 Section 6304.22 Public Lands: Interior Regulations Relating... apply to control of fire, insects, and diseases? BLM may prescribe measures to control fire, noxious weeds, non-native invasive plants, insects, and diseases. BLM may require restoration concurrent with or...

25 CFR 543.16 - What are the minimum internal controls for information technology?

Code of Federal Regulations, 2012 CFR

2012-04-01

... controls for information technology? (a) Physical security measures restricting access to agents, including... longer required. (2) In the event of remote access, the information technology employees must prepare a... 25 Indians 2 2012-04-01 2012-04-01 false What are the minimum internal controls for information...

25 CFR 543.16 - What are the minimum internal controls for information technology?

Code of Federal Regulations, 2011 CFR

2011-04-01

... controls for information technology? (a) Physical security measures restricting access to agents, including... longer required. (2) In the event of remote access, the information technology employees must prepare a... 25 Indians 2 2011-04-01 2011-04-01 false What are the minimum internal controls for information...

78 FR 48103 - Approval and Promulgation of Air Quality Implementation Plans; Illinois; Redesignation of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-07

... Redesignation Request ii. Subpart 4 Requirements and Illinois' Redesignation Request iii. Subpart 4 and Control... due to permanent and enforceable emission reductions? 1. Permanent and Enforceable Controls a. Federal Emission Control Measures i. Tier 2 Emission Standards for Vehicles and Gasoline Sulfur Standards ii. Heavy...

Computer program for post-flight evaluation of the control surface response for an attitude controlled missile

NASA Technical Reports Server (NTRS)

Knauber, R. N.

1982-01-01

A FORTRAN IV coded computer program is presented for post-flight analysis of a missile's control surface response. It includes preprocessing of digitized telemetry data for time lags, biases, non-linear calibration changes and filtering. Measurements include autopilot attitude rate and displacement gyro output and four control surface deflections. Simple first order lags are assumed for the pitch, yaw and roll axes of control. Each actuator is also assumed to be represented by a first order lag. Mixing of pitch, yaw and roll commands to four control surfaces is assumed. A pseudo-inverse technique is used to obtain the pitch, yaw and roll components from the four measured deflections. This program has been used for over 10 years on the NASA/SCOUT launch vehicle for post-flight analysis and was helpful in detecting incipient actuator stall due to excessive hinge moments. The program is currently set up for a CDC CYBER 175 computer system. It requires 34K words of memory and contains 675 cards. A sample problem presented herein including the optional plotting requires eleven (11) seconds of central processor time.

Active chatter suppression with displacement-only measurement in turning process

NASA Astrophysics Data System (ADS)

Ma, Haifeng; Wu, Jianhua; Yang, Liuqing; Xiong, Zhenhua

2017-08-01

Regenerative chatter is a major hindrance for achieving high quality and high production rate in machining processes. Various active controllers have been proposed to mitigate chatter. However, most of existing controllers were developed on the basis of multi-states feedback of the system and state observers were usually needed. Moreover, model parameters of the machining process (mass, damping and stiffness) were required in existing active controllers. In this study, an active sliding mode controller, which employs a dynamic output feedback sliding surface for the unmatched condition and an adaptive law for disturbance estimation, is designed, analyzed, and validated for chatter suppression in turning process. Only displacement measurement is required by this approach. Other sensors and state observers are not needed. Moreover, it facilitates a rapid implementation since the designed controller is established without using model parameters of the turning process. Theoretical analysis, numerical simulations and experiments on a computer numerical control (CNC) lathe are presented. It shows that the chatter can be substantially attenuated and the chatter-free region can be significantly expanded with the presented method.

Applications of fuzzy logic to control and decision making

NASA Technical Reports Server (NTRS)

Lea, Robert N.; Jani, Yashvant

1991-01-01

Long range space missions will require high operational efficiency as well as autonomy to enhance the effectivity of performance. Fuzzy logic technology has been shown to be powerful and robust in interpreting imprecise measurements and generating appropriate control decisions for many space operations. Several applications are underway, studying the fuzzy logic approach to solving control and decision making problems. Fuzzy logic algorithms for relative motion and attitude control have been developed and demonstrated for proximity operations. Based on this experience, motion control algorithms that include obstacle avoidance were developed for a Mars Rover prototype for maneuvering during the sample collection process. A concept of an intelligent sensor system that can identify objects and track them continuously and learn from its environment is under development to support traffic management and proximity operations around the Space Station Freedom. For safe and reliable operation of Lunar/Mars based crew quarters, high speed controllers with ability to combine imprecise measurements from several sensors is required. A fuzzy logic approach that uses high speed fuzzy hardware chips is being studied.

Novel Metrics to Characterize Embryonic Elongation of the Nematode Caenorhabditis elegans.

PubMed

Martin, Emmanuel; Rocheleau-Leclair, Olivier; Jenna, Sarah

2016-03-28

Dissecting the signaling pathways that control the alteration of morphogenic processes during embryonic development requires robust and sensitive metrics. Embryonic elongation of the nematode Caenorhabditis elegans is a late developmental stage consisting of the elongation of the embryo along its longitudinal axis. This developmental stage is controlled by intercellular communication between hypodermal cells and underlying body-wall muscles. These signaling mechanisms control the morphology of hypodermal cells by remodeling the cytoskeleton and the cell-cell junctions. Measurement of embryonic lethality and developmental arrest at larval stages as well as alteration of cytoskeleton and cell-cell adhesion structures in hypodermal and muscle cells are classical phenotypes that have been used for more than 25 years to dissect these signaling pathways. Recent studies required the development of novel metrics specifically targeting either early or late elongation and characterizing morphogenic defects along the antero-posterior axis of the embryo. Here, we provide detailed protocols enabling the accurate measurement of the length and the width of the elongating embryos as well as the length of synchronized larvae. These methods constitute useful tools to identify genes controlling elongation, to assess whether these genes control both early and late phases of this stage and are required evenly along the antero-posterior axis of the embryo.

Advanced optical sensing and processing technologies for the distributed control of large flexible spacecraft

NASA Technical Reports Server (NTRS)

Williams, G. M.; Fraser, J. C.

1991-01-01

The objective was to examine state-of-the-art optical sensing and processing technology applied to control the motion of flexible spacecraft. Proposed large flexible space systems, such an optical telescopes and antennas, will require control over vast surfaces. Most likely distributed control will be necessary involving many sensors to accurately measure the surface. A similarly large number of actuators must act upon the system. The used technical approach included reviewing proposed NASA missions to assess system needs and requirements. A candidate mission was chosen as a baseline study spacecraft for comparison of conventional and optical control components. Control system requirements of the baseline system were used for designing both a control system containing current off-the-shelf components and a system utilizing electro-optical devices for sensing and processing. State-of-the-art surveys of conventional sensor, actuator, and processor technologies were performed. A technology development plan is presented that presents a logical, effective way to develop and integrate advancing technologies.

Investigation of Space Interferometer Control Using Imaging Sensor Output Feedback

NASA Technical Reports Server (NTRS)

Leitner, Jesse A.; Cheng, Victor H. L.

2003-01-01

Numerous space interferometry missions are planned for the next decade to verify different enabling technologies towards very-long-baseline interferometry to achieve high-resolution imaging and high-precision measurements. These objectives will require coordinated formations of spacecraft separately carrying optical elements comprising the interferometer. High-precision sensing and control of the spacecraft and the interferometer-component payloads are necessary to deliver sub-wavelength accuracy to achieve the scientific objectives. For these missions, the primary scientific product of interferometer measurements may be the only source of data available at the precision required to maintain the spacecraft and interferometer-component formation. A concept is studied for detecting the interferometer's optical configuration errors based on information extracted from the interferometer sensor output. It enables precision control of the optical components, and, in cases of space interferometers requiring formation flight of spacecraft that comprise the elements of a distributed instrument, it enables the control of the formation-flying vehicles because independent navigation or ranging sensors cannot deliver the high-precision metrology over the entire required geometry. Since the concept can act on the quality of the interferometer output directly, it can detect errors outside the capability of traditional metrology instruments, and provide the means needed to augment the traditional instrumentation to enable enhanced performance. Specific analyses performed in this study include the application of signal-processing and image-processing techniques to solve the problems of interferometer aperture baseline control, interferometer pointing, and orientation of multiple interferometer aperture pairs.

Automated potentiometric electrolyte analysis system. [for use in weightlessness

NASA Technical Reports Server (NTRS)

1973-01-01

The feasibility is demonstrated of utilizing chemical sensing electrode technology as the basis for an automatically-controlled system for blood gas and electrolyte analyses under weightlessness conditions. The specific measurements required were pH, pCO2, sodium, chloride, potassium ions, and ionized calcium. The general electrode theory, and ion activity measurements are described along with the fluid transport package, electronics unit, and controller for the automated potentiometric analysis system.

Clean focus, dose and CD metrology for CD uniformity improvement

NASA Astrophysics Data System (ADS)

Lee, Honggoo; Han, Sangjun; Hong, Minhyung; Kim, Seungyoung; Lee, Jieun; Lee, DongYoung; Oh, Eungryong; Choi, Ahlin; Kim, Nakyoon; Robinson, John C.; Mengel, Markus; Pablo, Rovira; Yoo, Sungchul; Getin, Raphael; Choi, Dongsub; Jeon, Sanghuck

2018-03-01

Lithography process control solutions require more exacting capabilities as the semiconductor industry goes forward to the 1x nm node DRAM device manufacturing. In order to continue scaling down the device feature sizes, critical dimension (CD) uniformity requires continuous improvement to meet the required CD error budget. In this study we investigate using optical measurement technology to improve over CD-SEM methods in focus, dose, and CD. One of the key challenges is measuring scanner focus of device patterns. There are focus measurement methods based on specially designed marks on scribe-line, however, one issue of this approach is that it will report focus of scribe line which is potentially different from that of the real device pattern. In addition, scribe-line marks require additional design and troubleshooting steps that add complexity. In this study, we investigated focus measurement directly on the device pattern. Dose control is typically based on using the linear correlation behavior between dose and CD. The noise of CD measurement, based on CD-SEM for example, will not only impact the accuracy, but also will make it difficult to monitor dose signature on product wafers. In this study we will report the direct dose metrology result using an optical metrology system which especially enhances the DUV spectral coverage to improve the signal to noise ratio. CD-SEM is often used to measure CD after the lithography step. This measurement approach has the advantage of easy recipe setup as well as the flexibility to measure critical feature dimensions, however, we observe that CD-SEM metrology has limitations. In this study, we demonstrate within-field CD uniformity improvement through the extraction of clean scanner slit and scan CD behavior by using optical metrology.

49 CFR 40.351 - What confidentiality requirements apply to service agents?

Code of Federal Regulations, 2013 CFR

2013-10-01

... confidentiality and security measures to ensure that confidential employee records are not available to unauthorized persons. This includes protecting the physical security of records, access controls, and computer security measures to safeguard confidential data in electronic data bases. ...

49 CFR 40.351 - What confidentiality requirements apply to service agents?

Code of Federal Regulations, 2014 CFR

2014-10-01

... confidentiality and security measures to ensure that confidential employee records are not available to unauthorized persons. This includes protecting the physical security of records, access controls, and computer security measures to safeguard confidential data in electronic data bases. ...

49 CFR 40.351 - What confidentiality requirements apply to service agents?

Code of Federal Regulations, 2012 CFR

2012-10-01

... confidentiality and security measures to ensure that confidential employee records are not available to unauthorized persons. This includes protecting the physical security of records, access controls, and computer security measures to safeguard confidential data in electronic data bases. ...

49 CFR 40.351 - What confidentiality requirements apply to service agents?

Code of Federal Regulations, 2011 CFR

2011-10-01

... confidentiality and security measures to ensure that confidential employee records are not available to unauthorized persons. This includes protecting the physical security of records, access controls, and computer security measures to safeguard confidential data in electronic data bases. ...

Ground robotic measurement of aeolian processes

USDA-ARS?s Scientific Manuscript database

Models of aeolian processes rely on accurate measurements of the rates of sediment transport by wind, and careful evaluation of the environmental controls of these processes. Existing field approaches typically require intensive, event-based experiments involving dense arrays of instruments. These d...

New control design principles based on measured performance and energy analysis of HVAC (Heating, Ventilating, and Air-Conditioning) systems

NASA Astrophysics Data System (ADS)

Hittle, D. C.; Johnson, D. L.

1985-01-01

This report is one of a series on the development of heating, ventilating, and air-conditioning (HVAC) control systems that are simple, efficient, reliable, maintainable, and well-documented. This report identifies major problems associated with three currently used HVAC control systems. It also describes the development of a retrofit control system applicable to military buildings that will allow easy identification of component failures, facilitate repair, and minimize system failures. Evaluation of currently used controls showed that pneumatic temperature control equipment requires a very clean source of supply air and is also not very accurate. Pneumatic, rather than electronic, actuators should be used because they are cheaper and require less maintenance. Thermistor temperature detectors should not be used for HVAC applications because they require frequent calibration. It was found that enthalpy economy cycles cannot be used for control because the humidity sensors required for their use are prone to rapid drift, inaccurate, and hard to calibrate in the field. Performance of control systems greatly affects HVAC operating costs. Significant savings can be achieved if proportional-plus-integral control schemes are used. Use of the retrofit prototype control panel developed in this study on variable-air-volume systems should provide significant energy cost savings, improve comfort and reliability, and reduce maintenance costs.

Noncontact temperature measurements in the microgravity fluids and transport phenomena discipline

NASA Technical Reports Server (NTRS)

Salzman, Jack

1988-01-01

The program of activities within the Microgravity Fluids and Transport Phenomena Discipline has been structured to enable the systematic pursuit of an increased understanding of low gravity fluid behavior/phenomena in a way which ensures that the results are appropriate to the widest range of applications. This structure is discussed and an overview of some of the activities which are underway is given. Of significance is the fact that in the majority of the current and planned activities, the measurement and, or control of the fluid temperature is a key experiment requirement. In addition, many of the experiments require that the temperature measurement be nonintrusive. A description of these requirements together with the current techniques which are being employed or under study to make these measurements is also discussed.

Measurement and control of in-plane surface chemistry during the oxidation of H-terminated (111) Si

PubMed Central

Gokce, Bilal; Adles, Eric J.; Aspnes, David E.; Gundogdu, Kenan

2010-01-01

In-plane directional control of surface chemistry during interface formation can lead to new opportunities regarding device structures and applications. Control of this type requires techniques that can probe and hence provide feedback on the chemical reactivity of bonds not only in specific directions but also in real time. Here, we demonstrate both control and measurement of the oxidation of H-terminated (111) Si. Control is achieved by externally applying uniaxial strain, and measurement by second-harmonic generation (SHG) together with the anisotropic-bond model of nonlinear optics. In this system anisotropy results because bonds in the strain direction oxidize faster than those perpendicular to it, leading in addition to transient structural changes that can also be detected at the bond level by SHG. PMID:20876145

A dissociation between stopping and switching actions following a lesion of the pre-supplementary motor area

PubMed Central

Roberts, R. Edward; Husain, Masud

2015-01-01

Introduction Although the pre-supplementary motor area (pre-SMA) is one of the most frequently reported areas of activation in functional imaging studies, the role of this brain region in cognition is still a matter of intense debate. Here we present a patient with a focal lesion of caudal pre-SMA who displays a selective deficit in updating a response plan to switch actions, but shows no impairment when required to withhold a response – stopping. Materials & methods The patient and a control group underwent three tasks designed to measure different aspects of cognitive control and executive function. Results The pre-SMA patient displayed no impairment when responding in the face of distracting stimuli (Eriksen flanker paradigm), or when required to halt an on-going response (STOP task). However, a specific deficit was observed when she was required to rapidly switch between response plans (CHANGE task). Conclusions These findings suggest that the caudal pre-SMA may have a particularly important role in a network of brain regions required for rapidly updating and implementing response plans. The lack of any significant impairment on other measures of cognitive control suggests that this is not likely due to a global deficit in cognitive control. We discuss the implications of these results in the context of current theories of pre-SMA function. PMID:25282056

Assessment of Joystick control during the performance of powered wheelchair driving tasks

PubMed Central

2011-01-01

Background Powered wheelchairs are essential for many individuals who have mobility impairments. Nevertheless, if operated improperly, the powered wheelchair poses dangers to both the user and to those in its vicinity. Thus, operating a powered wheelchair with some degree of proficiency is important for safety, and measuring driving skills becomes an important issue to address. The objective of this study was to explore the discriminate validity of outcome measures of driving skills based on joystick control strategies and performance recorded using a data logging system. Methods We compared joystick control strategies and performance during standardized driving tasks between a group of 10 expert and 13 novice powered wheelchair users. Driving tasks were drawn from the Wheelchair Skills Test (v. 4.1). Data from the joystick controller were collected on a data logging system. Joystick control strategies and performance outcome measures included the mean number of joystick movements, time required to complete tasks, as well as variability of joystick direction. Results In simpler tasks, the expert group's driving skills were comparable to those of the novice group. Yet, in more difficult and spatially confined tasks, the expert group required fewer joystick movements for task completion. In some cases, experts also completed tasks in approximately half the time with respect to the novice group. Conclusions The analysis of joystick control made it possible to discriminate between novice and expert powered wheelchair users in a variety of driving tasks. These results imply that in spatially confined areas, a greater powered wheelchair driving skill level is required to complete tasks efficiently. Based on these findings, it would appear that the use of joystick signal analysis constitutes an objective tool for the measurement of powered wheelchair driving skills. This tool may be useful for the clinical assessment and training of powered wheelchair skills. PMID:21609435

Thermal monitoring, measurement, and control system for a Volatile Condensable Materials (VCM) test apparatus

NASA Technical Reports Server (NTRS)

Ives, R. E.

1982-01-01

A thermal monitoring and control concept is described for a volatile condensable materials (VCM) test apparatus where electric resistance heaters are employed. The technique is computer based, but requires only proportioning ON/OFF relay control signals supplied through a programmable scanner and simple quadrac power controllers. System uniqueness is derived from automatic temperature measurements and the averaging of these measurements in discrete overlapping temperature zones. Overall control tolerance proves to be better than + or - 0.5 C from room ambient temperature to 150 C. Using precisely calibrated thermocouples, the method provides excellent temperature control of a small copper VCM heating plate at 125 + or - 0.2 C over a 24 hr test period. For purposes of unattended operation, the programmable computer/controller provides a continual data printout of system operation. Real time operator command is also provided for, as is automatic shutdown of the system and operator alarm in the event of malfunction.

40 CFR 141.80 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.80 General requirements. (a... drinking water regulations for lead and copper. Unless otherwise indicated, each of the provisions of this... and copper action levels measured in samples collected at consumers' taps. (c) Lead and copper action...

Mobile robot trajectory tracking using noisy RSS measurements: an RFID approach.

PubMed

Miah, M Suruz; Gueaieb, Wail

2014-03-01

Most RF beacons-based mobile robot navigation techniques rely on approximating line-of-sight (LOS) distances between the beacons and the robot. This is mostly performed using the robot's received signal strength (RSS) measurements from the beacons. However, accurate mapping between the RSS measurements and the LOS distance is almost impossible to achieve in reverberant environments. This paper presents a partially-observed feedback controller for a wheeled mobile robot where the feedback signal is in the form of noisy RSS measurements emitted from radio frequency identification (RFID) tags. The proposed controller requires neither an accurate mapping between the LOS distance and the RSS measurements, nor the linearization of the robot model. The controller performance is demonstrated through numerical simulations and real-time experiments. ©2013 Published by ISA. All rights reserved.

Rotating pressure measurement system using an on board calibration standard

NASA Technical Reports Server (NTRS)

Senyitko, Richard G.; Blumenthal, Philip Z.; Freedman, Robert J.

1991-01-01

A computer-controlled multichannel pressure measurement system was developed to acquire detailed flow field measurements on board the Large Low Speed Centrifugal Compressor Research Facility at the NASA Lewis Research Center. A pneumatic slip ring seal assembly is used to transfer calibration pressures to a reference standard transducer on board the compressor rotor in order to measure very low differential pressures with the high accuracy required. A unique data acquisition system was designed and built to convert the analog signal from the reference transducer to the variable frequency required by the multichannel pressure measurement system and also to provide an output for temperature control of the reference transducer. The system also monitors changes in test cell barometric pressure and rotating seal leakage and provides an on screen warning to the operator if limits are exceeded. The methods used for the selection and testing of the the reference transducer are discussed, and the data acquisition system hardware and software design are described. The calculated and experimental data for the system measurement accuracy are also presented.

Radiation exposure levels within timber industries in Calabar, Nigeria

PubMed Central

Inyang, S. O.; Inyang, I. S.; Egbe, N. O.

2009-01-01

The UNSCEAR (2000) observed that there could be some exposure at work which would require regulatory control but is not really considered. This study was, therefore, set up to evaluate the effective dose in timber industries in Calabar, Nigeria to determine if the evaluated dose levels could lead to any radiological health effect in the workers, and also determine if the industries require regulatory control. The gamma ray exposure at four timber industries measured using an exposure meter were converted to effective dose and compared with the public and occupational values. The evaluated effective dose values in the timber industries were below public and occupational exposure limits and may not necessarily result in any radiological health hazard. Therefore, they may not require regulatory control. PMID:20098544

Measurement of whole tire profile

NASA Astrophysics Data System (ADS)

Yang, Yongyue; Jiao, Wenguang

2010-08-01

In this paper, a precision measuring device is developed for obtaining characteristic curve of tire profile and its geometric parameters. It consists of a laser displacement measurement unit, a closed-loop precision two-dimensional coordinate table, a step motor control system and a fast data acquisition and analysis system. Based on the laser trigonometry, a data map of tire profile and coordinate values of all points can be obtained through corresponding data transformation. This device has a compact structure, a convenient control, a simple hardware circuit design and a high measurement precision. Experimental results indicate that measurement precision can meet the customer accuracy requirement of +/-0.02 mm.

Minimum data requirement for neural networks based on power spectral density analysis.

PubMed

Deng, Jiamei; Maass, Bastian; Stobart, Richard

2012-04-01

One of the most critical challenges ahead for diesel engines is to identify new techniques for fuel economy improvement without compromising emissions regulations. One technique is the precise control of air/fuel ratio, which requires the measurement of instantaneous fuel consumption. Measurement accuracy and repeatability for fuel rate is the key to successfully controlling the air/fuel ratio and real-time measurement of fuel consumption. The volumetric and gravimetric measurement principles are well-known methods for measurement of fuel consumption in internal combustion engines. However, the fuel flow rate measured by these methods is not suitable for either real-time control or real-time measurement purposes because of the intermittent nature of the measurements. This paper describes a technique that can be used to find the minimum data [consisting of data from just 2.5% of the non-road transient cycle (NRTC)] to solve the problem concerning discontinuous data of fuel flow rate measured using an AVL 733S fuel meter for a medium or heavy-duty diesel engine using neural networks. Only torque and speed are used as the input parameters for the fuel flow rate prediction. Power density analysis is used to find the minimum amount of the data. The results show that the nonlinear autoregressive model with exogenous inputs could predict the particulate matter successfully with R(2) above 0.96 using 2.5% NRTC data with only torque and speed as inputs.

A dissociation of objective and subjective workload measures in assessing the impact of speech controls in advanced helicopters

NASA Technical Reports Server (NTRS)

Vidulich, Michael A.; Bortolussi, Michael R.

1988-01-01

Among the new technologies that are expected to aid helicopter designers are speech controls. Proponents suggest that speech controls could reduce the potential for manual control overloads and improve time-sharing performance in environments that have heavy demands for manual control. This was tested in a simulation of an advanced single-pilot, scout/attack helicopter. Objective performance indicated that the speech controls were effective in decreasing the interference of discrete responses during moments of heavy flight control activity. However, subjective ratings indicated that the use of speech controls required extra effort to speak precisely and to attend to feedback. Although the operational reliability of speech controls must be improved, the present results indicate that reliable speech controls could enhance the time-sharing efficiency of helicopter pilots. Furthermore, the results demonstrated the importance of using multiple assessment techniques to completely assess a task. Neither the objective nor the subjective measures alone provided complete information. It was the contrast between the measures that was most informative.

Reduced state feedback gain computation. [optimization and control theory for aircraft control

NASA Technical Reports Server (NTRS)

Kaufman, H.

1976-01-01

Because application of conventional optimal linear regulator theory to flight controller design requires the capability of measuring and/or estimating the entire state vector, it is of interest to consider procedures for computing controls which are restricted to be linear feedback functions of a lower dimensional output vector and which take into account the presence of measurement noise and process uncertainty. Therefore, a stochastic linear model that was developed is presented which accounts for aircraft parameter and initial uncertainty, measurement noise, turbulence, pilot command and a restricted number of measurable outputs. Optimization with respect to the corresponding output feedback gains was performed for both finite and infinite time performance indices without gradient computation by using Zangwill's modification of a procedure originally proposed by Powell. Results using a seventh order process show the proposed procedures to be very effective.

Online devices and measuring systems for the automatic control of newspaper printing

NASA Astrophysics Data System (ADS)

Marszalec, Elzbieta A.; Heikkila, Ismo; Juhola, Helene; Lehtonen, Tapio

1999-09-01

The paper reviews the state-of-the-art color measuring systems used for the control of newspaper printing. The printing process requirements are specified and different off-line and on-line color quality control systems, commercially available and under development, are evaluated. Recent market trends in newspaper printing are discussed based on the survey. The study was made on information derived from: conference proceedings (TAGA, IARIGAI, SPIE and IS&T), journals (American Printer, Applied Optics), discussions with experts (GMI, QTI, HONEYWELL, TOBIAS, GretagMacbeth), IFRA Expo'98/Quality Measuring Technologies, commercial brochures, and the Internet. On the background of this review, three different measuring principles, currently, under investigation at VTT Information Technology, are described and their applicability to newspaper printing is evaluated.

Accuracy assessment for a multi-parameter optical calliper in on line automotive applications

NASA Astrophysics Data System (ADS)

D'Emilia, G.; Di Gasbarro, D.; Gaspari, A.; Natale, E.

2017-08-01

In this work, a methodological approach based on the evaluation of the measurement uncertainty is applied to an experimental test case, related to the automotive sector. The uncertainty model for different measurement procedures of a high-accuracy optical gauge is discussed in order to individuate the best measuring performances of the system for on-line applications and when the measurement requirements are becoming more stringent. In particular, with reference to the industrial production and control strategies of high-performing turbochargers, two uncertainty models are proposed, discussed and compared, to be used by the optical calliper. Models are based on an integrated approach between measurement methods and production best practices to emphasize their mutual coherence. The paper shows the possible advantages deriving from the considerations that the measurement uncertainty modelling provides, in order to keep control of the uncertainty propagation on all the indirect measurements useful for production statistical control, on which basing further improvements.

[Malfunction simulation by spaceflight training simulator].

PubMed

Chang, Tian-chun; Zhang, Lian-hua; Xue, Liang; Lian, Shun-guo

2005-04-01

To implement malfunction simulation in spaceflight training simulator. The principle of malfunction simulation was defined according to spacecraft malfunction predict and its countermeasures. The malfunction patterns were classified, and malfunction type was confirmed. A malfunction simulation model was established, and the malfunction simulation was realized by math simulation. According to the requirement of astronaut training, a spacecraft subsystem malfunction simulation model was established and realized, such as environment control and life support, GNC, push, power supply, heat control, data management, measure control and communication, structure and so on. The malfunction simulation function implemented in the spaceflight training simulator satisfied the requirements for astronaut training.

A comparison of advanced overlay technologies

NASA Astrophysics Data System (ADS)

Dasari, Prasad; Smith, Nigel; Goelzer, Gary; Liu, Zhuan; Li, Jie; Tan, Asher; Koh, Chin Hwee

2010-03-01

The extension of optical lithography to 22nm and beyond by Double Patterning Technology is often challenged by CDU and overlay control. With reduced overlay measurement error budgets in the sub-nm range, relying on traditional Total Measurement Uncertainty (TMU) estimates alone is no longer sufficient. In this paper we will report scatterometry overlay measurements data from a set of twelve test wafers, using four different target designs. The TMU of these measurements is under 0.4nm, within the process control requirements for the 22nm node. Comparing the measurement differences between DBO targets (using empirical and model based analysis) and with image-based overlay data indicates the presence of systematic and random measurement errors that exceeds the TMU estimate.

CHALLENGES IN SETTING UP QUALITY CONTROL IN DIAGNOSTIC RADIOLOGY FACILITIES IN NIGERIA.

PubMed

Inyang, S O; Egbe, N O; Ekpo, E

2015-01-01

The Nigerian Nuclear Regulatory Authority (NNRA) was established to regulate and control the use of radioactive and radiation emitting sources in Nigeria. Quality control (QC) on diagnostic radiology equipment form part of the fundamental requirements for the authorization of diagnostic radiology facilities in the Country. Some quality control tests (output, exposure linearity and reproducibility) were measured on the x-ray machines in the facilities that took part in the study. Questionnaire was developed to evaluate the frequencies at which QC tests were conducted in the facilities and the challenges in setting up QC. Results show great variation in the values of the QC parameters measured. Inadequate cooperation by facilities management, lack of QC equipment and insufficient staff form the major challenges in setting up QC in the facilities under study. The responses on the frequencies at which QC tests should be conducted did not correspond to the recommended standards; indicating that personnel were not familiar with QC implementation and may require further training on QC.

40 CFR 122.26 - Storm water discharges (applicable to State NPDES programs, see § 123.25).

Code of Federal Regulations, 2013 CFR

2013-07-01

... controls are not needed based on a TMDL or, for non-impaired waters that do not require a TMDL, an... applied; the location and a description of existing structural and non-structural control measures to... controls would be those suitable to the site conditions and consistent with generally accepted engineering...

The Impact of Sub-Skills and Item Content on Students' Skills with Regard to the Control-of-Variables Strategy

ERIC Educational Resources Information Center

Schwichow, Martin; Christoph, Simon; Boone, William J.; Härtig, Hendrik

2016-01-01

The so-called control-of-variables strategy (CVS) incorporates the important scientific reasoning skills of designing controlled experiments and interpreting experimental outcomes. As CVS is a prominent component of science standards appropriate assessment instruments are required to measure these scientific reasoning skills and to evaluate the…

77 FR 28772 - Air Quality: Widespread Use for Onboard Refueling Vapor Recovery and Stage II Waiver

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

... required emissions control measure in Serious, Severe, and Extreme ozone nonattainment areas. Beginning... control on nearly all new highway vehicles since 2006. Over time, non- ORVR vehicles will continue to be replaced with ORVR vehicles. Stage II and ORVR emission control systems are redundant, and the EPA has...

Nanoparticle Enhancement Cascade for Sensitive Multiplex Measurements of Biomarkers in Complex Fluids with Surface Plasmon Resonance Imaging.

PubMed

Hendriks, Jan; Stojanovic, Ivan; Schasfoort, Richard B M; Saris, Daniël B F; Karperien, Marcel

2018-06-05

There is a large unmet need for reliable biomarker measurement systems for clinical application. Such systems should meet challenging requirements for large scale use, including a large dynamic detection range, multiplexing capacity, and both high specificity and sensitivity. More importantly, these requirements need to apply to complex biological samples, which require extensive quality control. In this paper, we present the development of an enhancement detection cascade for surface plasmon resonance imaging (SPRi). The cascade applies an antibody sandwich assay, followed by neutravidin and a gold nanoparticle enhancement for quantitative biomarker measurements in small volumes of complex fluids. We present a feasibility study both in simple buffers and in spiked equine synovial fluid with four cytokines, IL-1β, IL-6, IFN-γ, and TNF-α. Our enhancement cascade leads to an antibody dependent improvement in sensitivity up to 40 000 times, resulting in a limit of detection as low as 50 fg/mL and a dynamic detection range of more than 7 logs. Additionally, measurements at these low concentrations are highly reliable with intra- and interassay CVs between 2% and 20%. We subsequently showed this assay is suitable for multiplex measurements with good specificity and limited cross-reactivity. Moreover, we demonstrated robust detection of IL-6 and IL-1β in spiked undiluted equine synovial fluid with small variation compared to buffer controls. In addition, the availability of real time measurements provides extensive quality control opportunities, essential for clinical applications. Therefore, we consider this method is suitable for broad application in SPRi for multiplex biomarker detection in both research and clinical settings.

[Designing and implementation of a web-based quality monitoring system for plasma glucose measurement in multicenter population study].

PubMed

Liu, Yong; Wang, Limin; Pang, Richard; Mo, Nanxun; Hu, Yan; Deng, Qian; Hu, Zhaohui

2015-05-01

The aim of this paper is to describe the designing and implementation of a web-based plasma glucose measurement quality monitoring system to assess the analytical quality of plasma glucose measurements in multicenter population study and provide evidence for the future studies. In the chronic non-communicable disease and related factor surveillance in China, a web based quality monitoring system for plasma glucose measurement was established to conduct evaluation on plasma glucose monitoring quality and effectiveness in 302 surveillance centers, including quality control data entry, transmission and feedback. The majority of the surveillance centers met the quality requirements and passed the evaluation of reproducibility and precision of plasma glucose measurement, only a few centers required intensive training and re-assessment. In order to ensure the completeness and reliability of plasma glucose measurement in the surveillance centers, the establishment of web-based plasma glucose measurement quality control system can facilitate the identification of the qualified surveillance centers and evaluation of plasma glucose measurement quality in different regions. Communication and training are important in ensuring plasma glucose measurement quality. It is necessary to further improve this web-based plasma glucose measurement quality monitoring system in the future to reduce the method specific plasma glucose measurement bias.

The relationship between strategic control and conscious structural knowledge in artificial grammar learning.

PubMed

Norman, Elisabeth; Scott, Ryan B; Price, Mark C; Dienes, Zoltan

2016-05-01

We address Jacoby's (1991) proposal that strategic control over knowledge requires conscious awareness of that knowledge. In a two-grammar artificial grammar learning experiment all participants were trained on two grammars, consisting of a regularity in letter sequences, while two other dimensions (colours and fonts) varied randomly. Strategic control was measured as the ability to selectively apply the grammars during classification. For each classification, participants also made a combined judgement of (a) decision strategy and (b) relevant stimulus dimension. Strategic control was found for all types of decision strategy, including trials where participants claimed to lack conscious structural knowledge. However, strong evidence of strategic control only occurred when participants knew or guessed that the letter dimension was relevant, suggesting that strategic control might be associated with - or even causally requires - global awareness of the nature of the rules even though it does not require detailed knowledge of their content. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

IDSAC-IUCAA digital sampler array controller

NASA Astrophysics Data System (ADS)

Chattopadhyay, Sabyasachi; Chordia, Pravin; Ramaprakash, A. N.; Burse, Mahesh P.; Joshi, Bhushan; Chillal, Kalpesh

2016-07-01

In order to run the large format detector arrays and mosaics that are required by most astronomical instruments, readout electronic controllers are required which can process multiple CCD outputs simultaneously at high speeds and low noise levels. These CCD controllers need to be modular and configurable, should be able to run multiple detector types to cater to a wide variety of requirements. IUCAA Digital Sampler Array Controller (IDSAC), is a generic CCD Controller based on a fully scalable architecture which is adequately flexible and powerful enough to control a wide variety of detectors used in ground based astronomy. The controller has a modular backplane architecture that consists of Single Board Controller Cards (SBCs) and can control up to 5 CCDs (mosaic or independent). Each Single Board Controller (SBC) has all the resources to a run Single large format CCD having up to four outputs. All SBCs are identical and are easily interchangeable without needing any reconfiguration. A four channel video processor on each SBC can process up to four output CCDs with or without dummy outputs at 0.5 Megapixels/Sec/Channel with 16 bit resolution. Each SBC has a USB 2.0 interface which can be connected to a host computer via optional USB to Fibre converters. The SBC uses a reconfigurable hardware (FPGA) as a Master Controller. IDSAC offers Digital Correlated Double Sampling (DCDS) to eliminate thermal kTC noise. CDS performed in Digital domain (DCDS) has several advantages over its analog counterpart, such as - less electronics, faster readout and easier post processing. It is also flexible with sampling rate and pixel throughput while maintaining the core circuit topology intact. Noise characterization of the IDSAC CDS signal chain has been performed by analytical modelling and practical measurements. Various types of noise such as white, pink, power supply, bias etc. has been considered while creating an analytical noise model tool to predict noise of a controller system like IDSAC. Several tests are performed to measure the actual noise of IDSAC. The theoretical calculation matches very well with practical measurements within 10% accuracy.

Performance monitor system functional simulator, environmental data, orbiter 101(HFT)

NASA Technical Reports Server (NTRS)

Parker, F. W.

1974-01-01

Information concerning the environment component of the space shuttle performance monitor system simulator (PMSS) and those subsystems operational on the shuttle orbiter 101 used for horizontal flight test (HFT) is provided, along with detailed data for the shuttle performance monitor system (PMS) whose software requirements evolve from three basic PMS functions: (1) fault detection and annunciation; (2) subsystem measurement management; and (3) subsystem configuration management. Information relative to the design and operation of Orbiter systems for HFT is also presented, and the functional paths are identified to the lowest level at which the crew can control the system functions. Measurement requirements are given which are necessary to adequately monitor the health status of the system. PMS process requirements, relative to the measurements which are necessary for fault detection and annunciation of a failed functional path, consist of measurement characteristics, tolerance limits, precondition tests, and correlation measurements.

Computation of records of streamflow at control structures

USGS Publications Warehouse

Collins, Dannie L.

1977-01-01

Traditional methods of computing streamflow records on large, low-gradient streams require a continuous record of water-surface slope over a natural channel reach. This slope must be of sufficient magnitude to be accuratly measured with available stage measuring devices. On highly regulated streams, this slope approaches zero during periods of low flow and accurate measurement is difficult. Methods are described to calibrate multipurpose regulating control structures to more accurately compute streamflow records on highly-regulated streams. Hydraulic theory, assuming steady, uniform flow during a computational interval, is described for five different types of flow control. The controls are: Tainter gates, hydraulic turbines, fixed spillways, navigation locks, and crest gates. Detailed calibration procedures are described for the five different controls as well as for several flow regimes for some of the controls. The instrumentation package and computer programs necessary to collect and process the field data are discussed. Two typical calibration procedures and measurement data are presented to illustrate the accuracy of the methods. (Woodard-USGS)

78 FR 20039 - Reportable Events and Certain Other Notification Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-03

...'' test and four other criteria designed to measure various aspects of financial soundness. The credit... controlled group changes. Like section 4043, the reportable events regulation generally requires post-event... available for plans that could meet one of two funding tests that would be more stringent than those...

Hydrologic controls on nitrogen availability in a high-latitude, semi-arid floodplain.

Treesearch

Nicholas J. Lisuzzo; Knut Kielland; Jeremy B. Jones

2008-01-01

Past research shows a discrepancy between apparent nitrogen supply and the annual growth requirements for early successional plant communities along the Tanana River floodplain in interior Alaska. Because previous measurements of nitrogen fixation, mineralization, and deposition can only account for approximately 26% of these communities' nitrogen requirements,...

27 CFR 19.193 - Breaking Government locks.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Breaking Government locks... Requirements Other Plant Requirements § 19.193 Breaking Government locks. TTB may assign TTB officers to a distilled spirits plant and utilize controls, such as Government locks, if TTB determines that such measures...

77 FR 20505 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-05

... Company Model 757 airplanes. This AD requires replacing the power control relays for the fuel boost pumps and override pumps with new relays having a ground fault interrupter (GFI) feature. This AD also requires an electrical bonding resistance measurement for certain GFI relays to verify that certain bonding...

Active Mirror Predictive and Requirements Verification Software (AMP-ReVS)

NASA Technical Reports Server (NTRS)

Basinger, Scott A.

2012-01-01

This software is designed to predict large active mirror performance at various stages in the fabrication lifecycle of the mirror. It was developed for 1-meter class powered mirrors for astronomical purposes, but is extensible to other geometries. The package accepts finite element model (FEM) inputs and laboratory measured data for large optical-quality mirrors with active figure control. It computes phenomenological contributions to the surface figure error using several built-in optimization techniques. These phenomena include stresses induced in the mirror by the manufacturing process and the support structure, the test procedure, high spatial frequency errors introduced by the polishing process, and other process-dependent deleterious effects due to light-weighting of the mirror. Then, depending on the maturity of the mirror, it either predicts the best surface figure error that the mirror will attain, or it verifies that the requirements for the error sources have been met once the best surface figure error has been measured. The unique feature of this software is that it ties together physical phenomenology with wavefront sensing and control techniques and various optimization methods including convex optimization, Kalman filtering, and quadratic programming to both generate predictive models and to do requirements verification. This software combines three distinct disciplines: wavefront control, predictive models based on FEM, and requirements verification using measured data in a robust, reusable code that is applicable to any large optics for ground and space telescopes. The software also includes state-of-the-art wavefront control algorithms that allow closed-loop performance to be computed. It allows for quantitative trade studies to be performed for optical systems engineering, including computing the best surface figure error under various testing and operating conditions. After the mirror manufacturing process and testing have been completed, the software package can be used to verify that the underlying requirements have been met.

Selective Attention to Emotion in the Aging Brain

PubMed Central

Samanez-Larkin, Gregory R.; Robertson, Elaine R.; Mikels, Joseph A.; Carstensen, Laura L.; Gotlib, Ian H.

2009-01-01

A growing body of research suggests that the ability to regulate emotion remains stable or improves across the adult life span. Socioemotional selectivity theory maintains that this pattern of findings reflects the prioritization of emotional goals. Given that goal-directed behavior requires attentional control, the present study was designed to investigate age differences in selective attention to emotional lexical stimuli under conditions of emotional interference. Both neural and behavioral measures were obtained during an experiment in which participants completed a flanker task that required them to make categorical judgments about emotional and non-emotional stimuli. Older adults showed interference in both the behavioral and neural measures on control trials, but not on emotion trials. Although older adults typically show relatively high levels of interference and reduced cognitive control during non-emotional tasks, they appear to be able successfully to reduce interference during emotional tasks. PMID:19739908

Thermal Control Subsystem Design for the Avionics of a Space Station Payload

NASA Technical Reports Server (NTRS)

Moran, Matthew E.

1996-01-01

A case study of the thermal control subsystem development for a space based payload is presented from the concept stage through preliminary design. This payload, the Space Acceleration Measurement System 2 (SAMS-2), will measure the acceleration environment at select locations within the International Space Station. Its thermal control subsystem must maintain component temperatures within an acceptable range over a 10 year life span, while restricting accessible surfaces to touch temperature limits and insuring fail safe conditions in the event of loss of cooling. In addition to these primary design objectives, system level requirements and constraints are imposed on the payload, many of which are driven by multidisciplinary issues. Blending these issues into the overall system design required concurrent design sessions with the project team, iterative conceptual design layouts, thermal analysis and modeling, and hardware testing. Multiple tradeoff studies were also performed to investigate the many options which surfaced during the development cycle.

Selective attention to emotion in the aging brain.

PubMed

Samanez-Larkin, Gregory R; Robertson, Elaine R; Mikels, Joseph A; Carstensen, Laura L; Gotlib, Ian H

2009-09-01

A growing body of research suggests that the ability to regulate emotion remains stable or improves across the adult life span. Socioemotional selectivity theory maintains that this pattern of findings reflects the prioritization of emotional goals. Given that goal-directed behavior requires attentional control, the present study was designed to investigate age differences in selective attention to emotional lexical stimuli under conditions of emotional interference. Both neural and behavioral measures were obtained during an experiment in which participants completed a flanker task that required them to make categorical judgments about emotional and nonemotional stimuli. Older adults showed interference in both the behavioral and neural measures on control trials but not on emotion trials. Although older adults typically show relatively high levels of interference and reduced cognitive control during nonemotional tasks, they appear to be able to successfully reduce interference during emotional tasks. (c) 2009 APA, all rights reserved.

Practical aspects of modeling aircraft dynamics from flight data

NASA Technical Reports Server (NTRS)

Iliff, K. W.; Maine, R. E.

1984-01-01

The purpose of parameter estimation, a subset of system identification, is to estimate the coefficients (such as stability and control derivatives) of the aircraft differential equations of motion from sampled measured dynamic responses. In the past, the primary reason for estimating stability and control derivatives from flight tests was to make comparisons with wind tunnel estimates. As aircraft became more complex, and as flight envelopes were expanded to include flight regimes that were not well understood, new requirements for the derivative estimates evolved. For many years, the flight determined derivatives were used in simulations to aid in flight planning and in pilot training. The simulations were particularly important in research flight test programs in which an envelope expansion into new flight regimes was required. Parameter estimation techniques for estimating stability and control derivatives from flight data became more sophisticated to support the flight test programs. As knowledge of these new flight regimes increased, more complex aircraft were flown. Much of this increased complexity was in sophisticated flight control systems. The design and refinement of the control system required higher fidelity simulations than were previously required.

Working memory capacity and the scope and control of attention.

PubMed

Shipstead, Zach; Harrison, Tyler L; Engle, Randall W

2015-08-01

Complex span and visual arrays are two common measures of working memory capacity that are respectively treated as measures of attention control and storage capacity. A recent analysis of these tasks concluded that (1) complex span performance has a relatively stronger relationship to fluid intelligence and (2) this is due to the requirement that people engage control processes while performing this task. The present study examines the validity of these conclusions by examining two large data sets that include a more diverse set of visual arrays tasks and several measures of attention control. We conclude that complex span and visual arrays account for similar amounts of variance in fluid intelligence. The disparity relative to the earlier analysis is attributed to the present study involving a more complete measure of the latent ability underlying the performance of visual arrays. Moreover, we find that both types of working memory task have strong relationships to attention control. This indicates that the ability to engage attention in a controlled manner is a critical aspect of working memory capacity, regardless of the type of task that is used to measure this construct.

Engineering challenges of BioNEMS: the integration of microfluidics, micro- and nanodevices, models and external control for systems biology.

PubMed

Wikswo, J P; Prokop, A; Baudenbacher, F; Cliffel, D; Csukas, B; Velkovsky, M

2006-08-01

Systems biology, i.e. quantitative, postgenomic, postproteomic, dynamic, multiscale physiology, addresses in an integrative, quantitative manner the shockwave of genetic and proteomic information using computer models that may eventually have 10(6) dynamic variables with non-linear interactions. Historically, single biological measurements are made over minutes, suggesting the challenge of specifying 10(6) model parameters. Except for fluorescence and micro-electrode recordings, most cellular measurements have inadequate bandwidth to discern the time course of critical intracellular biochemical events. Micro-array expression profiles of thousands of genes cannot determine quantitative dynamic cellular signalling and metabolic variables. Major gaps must be bridged between the computational vision and experimental reality. The analysis of cellular signalling dynamics and control requires, first, micro- and nano-instruments that measure simultaneously multiple extracellular and intracellular variables with sufficient bandwidth; secondly, the ability to open existing internal control and signalling loops; thirdly, external BioMEMS micro-actuators that provide high bandwidth feedback and externally addressable intracellular nano-actuators; and, fourthly, real-time, closed-loop, single-cell control algorithms. The unravelling of the nested and coupled nature of cellular control loops requires simultaneous recording of multiple single-cell signatures. Externally controlled nano-actuators, needed to effect changes in the biochemical, mechanical and electrical environment both outside and inside the cell, will provide a major impetus for nanoscience.

Stability of ionized calcium measurements at concentrations less than 0.3 mmol/L by point-of-care blood gas instruments: application for postfilter calcium quality control in patients with citrate anticoagulation during extracorporeal circulation.

PubMed

Averina, Maria; Jakobsen, Raymond

2017-05-01

Background Measurements of ionized calcium (Ca 2+ ) at concentrations less than 0.3 mmol/L are required for postfilter control in patients who receive extracorporeal circulation with sodium citrate anticoagulation. This study evaluates the stability of the Ca 2+ measurements at such concentrations. Methods The stability of the Ca 2+ measurements was tested by measuring daily the external standard Qualicheck concentration 3 s7950, Radiometer (0.22-0.25 mmol/L) by blood gas instruments ABL800 and ABL90, Radiometer. Two different Ca 2+ membrane lots were tested for the usual membrane lifetime of 12 weeks at ABL800 instruments. For the ABL90 instrument, the sensor cassette (with Ca 2+ membrane and electrode) was replaced after four weeks as required. Results We observed over 40% Ca 2+ increase within the usual 12 weeks lifetime of the Ca 2+ membrane at the ABL800 instruments. Measurements of Ca 2+ at concentrations less than 0.3 mmol/L were within acceptable limits for both ABL800 and ABL90 instruments when Ca 2+ membrane and sensor cassette were replaced after four weeks. Conclusions For ABL800 instruments, it is necessary to use an extra quality control (<0.3 mmol/L) in addition to the usual quality controls to monitor Ca 2+ measurements below 0.3 mmol/L. The acceptable stability of the Ca 2+ measurements can be achieved by the Ca 2+ membrane and sensor cassette replacement after four weeks. If the usual 12 weeks of Ca 2+ membrane lifetime is maintained, it may result in a clinically significant overestimation of Ca 2+ by ABL800 instruments.

A generic testbed for the design of plasma spectrometer control software with application to the THOR-CSW solar wind instrument

NASA Astrophysics Data System (ADS)

De Keyser, Johan; Lavraud, Benoit; Neefs, Eddy; Berkenbosch, Sophie; Beeckman, Bram; Maggiolo, Romain; Gamby, Emmanuel; Fedorov, Andrei; Baruah, Rituparna; Wong, King-Wah; Amoros, Carine; Mathon, Romain; Génot, Vincent; Marcucci, Federica; Brienza, Daniele

2017-04-01

Modern plasma spectrometers require intelligent software that is able to exploit their capabilities to the fullest. While the low-level control of the instrument and basic tasks such as performing the basic measurement, temperature control, and production of housekeeping data are to be done by software that is executed on an FPGA and/or processor inside the instrument, higher level tasks such as control of measurement sequences, on-board moment calculation, beam tracking decisions, and data compression, may be performed by the instrument or in the payload data processing unit. Such design decisions, as well as an assessment of the workload on the different processing components, require early prototyping. We have developed a generic simulation testbed for the design of plasma spectrometer control software that allows an early evaluation of the level of resources that is needed at each level. Early prototyping can pinpoint bottlenecks in the design allowing timely remediation. We have applied this tool to the THOR Cold Solar Wind (CSW) plasma spectrometer. Some examples illustrating the usefulness of the tool are given.

Expertise on Cognitive Workloads and Performance During Navigation and Target Detection

DTIC Science & Technology

2012-03-01

requiring little or no attention 1. Little confusion, risk, frustration, or anxiety exists and can be easily accomodated 2. Occasionally have spare...to confusion, frustration, or anxiety noticeably adds to workload. Significant compensation is required to maintain adequate performance. 3... anxiety . High to extreme determination and self- control required 59 Field Description elapsedTime (sec) Continuous measurement of time from the

Asthma Quiz

MedlinePlus

... Asthma is a chronic disease that requires ongoing management. Personalized plans for treatment may include medications, an asthma action plan, and environmental control measures to avoid your child's asthma triggers. ...

Plasma source for spacecraft potential control

NASA Technical Reports Server (NTRS)

Olsen, R. C.

1983-01-01

A stable electrical ground which enables the particle spectrometers to measure the low energy particle populations was investigated and the current required to neutralize the spacecraft was measured. In addition, the plasma source for potential control (PSPO C) prevents high charging events which could affect the spacecraft electrical integrity. The plasma source must be able to emit a plasma current large enough to balance the sum of all other currents to the spacecraft. In ion thrusters, hollow cathodes provide several amperes of electron current to the discharge chamber. The PSPO C is capable of balancing the net negative currents found in eclipse charging events producing 10 to 100 microamps of electron current. The largest current required is the ion current necessary to balance the total photoelectric current.

C/SCSC overview: approach, implementation, use. [Cost/Schedule Control Systems Criteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turf, Larry

1979-01-01

An overview of the Cost/Schedule Control System Criteria, known as C/SCS or C/S Squared is pesented. In the mid-1960s, several DOD service agencies embarked on a new performance measurement concept to track cost and schedule performance on major DOD programs. The performance measurement concept of C/SCS has expanded from DOD use to the Department of Energy (PMS), NASA (533 reports), and private industry such as shipbuilding, utilities, and construction. This paper describes the C/SCSC with the events leading to the C/SCS requirement, how to approach the requirement, and discusses implementing and using the system. Many government publications, directives, and instructionsmore » on the subject are listed in the publication.« less

Phytometric intelligence sensors

NASA Technical Reports Server (NTRS)

Seelig, Hans-Dieter (Inventor); Stoner, II, Richard J. (Inventor); Hoehn, Alexander (Inventor); Adams, III, William Walter (Inventor)

2010-01-01

Methods and apparatus for determining when plants require watering, and methods of attending to the watering of plants including signaling the grower that the plants are in need of hydration are provided. The novel methods include real-time measurement of plant metabolics and phytometric physiology changes of intrinsic physical or behavioral traits within the plant such as determining physiological flux measurement of enzyme flux due to environmental changes such as the wind and drought stress, soil and plant mineral deficiencies, or the interaction with a bio-control for organic disease control including, cell movement, signal transduction, internal chemical processes and external environmental processes including when plants require watering, and methods of attending to the watering of plants including signaling the grower that the plants are in need of hydration.

Development of a wearable measurement and control unit for personal customizing machine-supported exercise.

PubMed

Wang, Zhihui; Tamura, Naoki; Kiryu, Tohru

2005-01-01

Wearable technology has been used in various health-related fields to develop advanced monitoring solutions. However, the monitoring function alone cannot meet all the requirements of personal customizing machine-supported exercise that have biosignal-based controls. In this paper, we propose a new wearable unit design equipped with measurement and control functions to support the personal customization process. The wearable unit can measure the heart rate and electromyogram signals during exercise and output workload control commands to the exercise machines. We then applied a prototype of the wearable unit to an Internet-based cycle ergometer system. The wearable unit was examined using twelve young people to check its feasibility. The results verified that the unit could successfully adapt to the control of the workload and was effective for continuously supporting gradual changes in physical activities.

Designing Control System Application Software for Change

NASA Technical Reports Server (NTRS)

Boulanger, Richard

2001-01-01

The Unified Modeling Language (UML) was used to design the Environmental Systems Test Stand (ESTS) control system software. The UML was chosen for its ability to facilitate a clear dialog between software designer and customer, from which requirements are discovered and documented in a manner which transposes directly to program objects. Applying the UML to control system software design has resulted in a baseline set of documents from which change and effort of that change can be accurately measured. As the Environmental Systems Test Stand evolves, accurate estimates of the time and effort required to change the control system software will be made. Accurate quantification of the cost of software change can be before implementation, improving schedule and budget accuracy.

Mass Property Measurements of the Mars Science Laboratory Rover

NASA Technical Reports Server (NTRS)

Fields, Keith

2012-01-01

The NASA/JPL Mars Science Laboratory (MSL) spacecraft mass properties were measured on a spin balance table prior to launch. This paper discusses the requirements and issues encountered with the setup, qualification, and testing using the spin balance table, and the idiosyncrasies encountered with the test system. The final mass measurements were made in the Payload Hazardous Servicing Facility (PHSF) at Kennedy Space Center on the fully assembled and fueled spacecraft. This set of environmental tests required that the control system for the spin balance machine be at a remote location, which posed additional challenges to the operation of the machine

Recall initiation strategies must be controlled in training studies that use immediate free recall tasks to measure the components of working memory capacity across time.

PubMed

Gibson, Bradley S; Gondoli, Dawn M; Johnson, Ann C; Robison, Matthew K

2014-01-01

There has been great interest in using working memory (WM) training regimens as an alternative treatment for ADHD, but it has recently been concluded that existing training regimens may not be optimally designed because they target the primary memory component but not the secondary component of WM capacity. This conclusion requires the ability to accurately measure changes in primary and secondary memory abilities over time. The immediate free recall task has been used in previous studies to measure these changes; however, one concern with these tasks is that the recall order required on training exercises may influence the recall strategy used during free recall, which may in turn influence the relative number of items recalled from primary and secondary memory. To address this issue, previous training studies have explicitly controlled recall strategy before and after training. However, the necessity of controlling for recall strategies has not been explicitly tested. The present study investigated the effects of forward-serial-order training on free recall performance under conditions in which recall strategy was not controlled using a sample of adolescents with ADHD. Unlike when recall order was controlled, the main findings showed selective improvement of the secondary memory component (as opposed to the primary memory component) when recall order was uncontrolled. This finding advances our understanding of WM training by highlighting the importance of controlling for recall strategies when free recall tasks are used to measure changes in the primary and secondary components of WM across time.

Working memory capacity and the top-down control of visual search: Exploring the boundaries of "executive attention".

PubMed

Kane, Michael J; Poole, Bradley J; Tuholski, Stephen W; Engle, Randall W

2006-07-01

The executive attention theory of working memory capacity (WMC) proposes that measures of WMC broadly predict higher order cognitive abilities because they tap important and general attention capabilities (R. W. Engle & M. J. Kane, 2004). Previous research demonstrated WMC-related differences in attention tasks that required restraint of habitual responses or constraint of conscious focus. To further specify the executive attention construct, the present experiments sought boundary conditions of the WMC-attention relation. Three experiments correlated individual differences in WMC, as measured by complex span tasks, and executive control of visual search. In feature-absence search, conjunction search, and spatial configuration search, WMC was unrelated to search slopes, although they were large and reliably measured. Even in a search task designed to require the volitional movement of attention (J. M. Wolfe, G. A. Alvarez, & T. S. Horowitz, 2000), WMC was irrelevant to performance. Thus, WMC is not associated with all demanding or controlled attention processes, which poses problems for some general theories of WMC. Copyright 2006 APA, all rights reserved.

Development and implementation of an automated quantitative film digitizer quality control program

NASA Astrophysics Data System (ADS)

Fetterly, Kenneth A.; Avula, Ramesh T. V.; Hangiandreou, Nicholas J.

1999-05-01

A semi-automated, quantitative film digitizer quality control program that is based on the computer analysis of the image data from a single digitized test film was developed. This program includes measurements of the geometric accuracy, optical density performance, signal to noise ratio, and presampled modulation transfer function. The variability of the measurements was less than plus or minus 5%. Measurements were made on a group of two clinical and two laboratory laser film digitizers during a trial period of approximately four months. Quality control limits were established based on clinical necessity, vendor specifications and digitizer performance. During the trial period, one of the digitizers failed the performance requirements and was corrected by calibration.

General Procedure for Protective Cooling and Equipment Evaluations Relative to Heat and Cold Stress

DTIC Science & Technology

2008-09-01

climatic chamber housing the manikin. The most widely accepted test procedures for the operation of a TM are published by the American Society for...describes measurement of the clo value of a complete clothing ensemble. It requires a TM surface temperature of 35ºC and a climatic chamber controlled...Clothing Using a Sweating Manikin” (1) measures the im of a complete clothing ensemble. It requires a TM surface temperature of 35ºC and a climatic

A Reward-Based Behavioral Platform to Measure Neural Activity during Head-Fixed Behavior.

PubMed

Micallef, Andrew H; Takahashi, Naoya; Larkum, Matthew E; Palmer, Lucy M

2017-01-01

Understanding the neural computations that contribute to behavior requires recording from neurons while an animal is behaving. This is not an easy task as most subcellular recording techniques require absolute head stability. The Go/No-Go sensory task is a powerful decision-driven task that enables an animal to report a binary decision during head-fixation. Here we discuss how to set up an Ardunio and Python based platform system to control a Go/No-Go sensory behavior paradigm. Using an Arduino micro-controller and Python-based custom written program, a reward can be delivered to the animal depending on the decision reported. We discuss the various components required to build the behavioral apparatus that can control and report such a sensory stimulus paradigm. This system enables the end user to control the behavioral testing in real-time and therefore it provides a strong custom-made platform for probing the neural basis of behavior.

Improved dewpoint-probe calibration

NASA Technical Reports Server (NTRS)

Stephenson, J. G.; Theodore, E. A.

1978-01-01

Relatively-simple pressure-control apparatus calibrates dewpoint probes considerably faster than conventional methods, with no loss of accuracy. Technique requires only pressure measurement at each calibration point and single absolute-humidity measurement at beginning of run. Several probes can be calibrated simultaneously and points can be checked above room temperature.

An Arduino-Controlled Photogate

ERIC Educational Resources Information Center

Galeriu, Calin

2013-01-01

It is hard to imagine teaching physics without doing experimental measurements of position as a function of time. These measurements, needed for the determination of velocity and acceleration, are most easily performed with the help of photogates. Unfortunately, commercial photogates are rather expensive. Many require the purchase of an additional…

Semiconductor Measurement Technology: Progress Report October 1 to December 31, 1974

DTIC Science & Technology

1975-11-01

the Nomarski differential interference contrast mode. The magnification as measured on the photo- microgranh was 58?X. From these photo...linear encoder or a laser Interferometrically controlled stage. A schematic diagram of this system Is shown In figure 23. The required resolution of

40 CFR 1065.659 - Removed water correction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Removed water correction. 1065.659... CONTROLS ENGINE-TESTING PROCEDURES Calculations and Data Requirements § 1065.659 Removed water correction. (a) If you remove water upstream of a concentration measurement, x, or upstream of a flow measurement...

33 CFR 105.255 - Security measures for access control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and facilities; (4) Granting access to only those responding to the security incident or threat... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Security measures for access... SECURITY MARITIME SECURITY MARITIME SECURITY: FACILITIES Facility Security Requirements § 105.255 Security...

The role of fiberoptics in remote temperature measurement

NASA Technical Reports Server (NTRS)

Vanzetti, Riccardo

1988-01-01

The use of optical fibers in conjunction with infrared detectors and signal processing electronics represents the latest advance in the field of non-contact temperature measurement and control. The operating principles and design of fiber-optic radiometric systems are discussed and the advantages and disadvantages of using optical fibers are addressed. Signal processing requirements and various infrared detector types are also described. Several areas in which infrared fiber-optic instrumentation is used for temperature monitoring and control are discussed.

Lignin Sensor Based On Flash-Pyrolysis Mass Spectrometry

NASA Technical Reports Server (NTRS)

Kwack, Eug Y.; Lawson, Daniel D.; Shakkottai, Parthasarathy

1990-01-01

New lignin sensor takes only few minutes to measure lignin content of specimen of wood, pulp, paper, or similar material. Includes flash pyrolizer and ion-trap detector that acts as mass spectrometer. Apparatus measures amount of molecular fragments of lignin in pyrolysis products of samples. Helpful in controlling digestors in paper mills to maintain required lignin content, and also in bleaching plants, where good control of bleaching becomes possible if quick determination of lignin content made.

The epidemics of bovine spongiform encephalopathy and variant Creutzfeldt-Jakob disease: current status and future prospects.

PubMed Central

Smith, Peter G.

2003-01-01

The large epidemic of bovine spongiform encephalopathy (BSE) in the United Kingdom has been in decline since 1992, but has spread to other countries. The extensive control measures that have been put in place across the European Union and also in Switzerland should have brought the transmission of BSE under control in these countries, provided that the measures were properly enforced. Postmortem tests on brain tissue enable infected animals to be detected during the late stages of the incubation period, but tests that can be performed on live animals (including humans) and that will detect infections early are urgently needed. The number of infected animals currently entering the food chain is probably small, and the controls placed on bovine tissues in the European Union and Switzerland should ensure that any risks to human health are small and diminishing. Vigilance is required in all countries, especially in those in which there has been within-species recycling of ruminant feed. Fewer than 150 people, globally, have been diagnosed with variant Creutzfeldt-Jakob disease (vCJD), but there are many uncertainties about the future course of the epidemic because of the long and variable incubation period. Better control measures are necessary to guard against the possibility of iatrogenic transmission through blood transfusion or contaminated surgical instruments. These measures will required sensitive and specific, diagnostic tests and improved decontamination methods. PMID:12751420

Optimal Control Design using an H(sub 2) Method for the Glovebox Integrated Microgravity Isolation Technology (G-Limit)

NASA Technical Reports Server (NTRS)

Calhoun, Philip C.; Hampton, R. David

2002-01-01

The acceleration environment on the International Space Station (ISS) will likely exceed the requirements of many micro-gravity experiments. The Glovebox Integrated Microgravity Isolation Technology (g-LIMIT) is being built by the NASA Marshall Space Flight Center to attenuate the nominal acceleration environment and provide some isolation for microgravity science experiments. G-LIMIT uses Lorentz (voice-coil) magnetic actuators to isolate a platform for mounting science payloads from the nominal acceleration environment. The system utilizes payload acceleration, relative position, and relative orientation measurements in a feedback controller to accomplish the vibration isolation task. The controller provides current commands to six magnetic actuators, producing the required experiment isolation from the ISS acceleration environment. This paper presents the development of a candidate control law to meet the acceleration attenuation requirements for the g-LIMIT experiment platform. The controller design is developed using linear optimal control techniques for frequency-weighted H(sub 2) norms. Comparison of the performance and robustness to plant uncertainty for this control design approach is included in the discussion.

Frequency Weighted H2 Control Design for the Glovebox Integrated Microgravity Isolation Technology (g-LIMIT)

NASA Technical Reports Server (NTRS)

Calhoun, Philip C.; Hampton, R. David

2004-01-01

The acceleration environment on the International Space Station (ISS) exceeds the requirements of many microgravity experiments. The Glovebox Integrated Microgravity Isolation Technology (g-LIMIT) has been built by the NASA Marshall Space Flight Center to attenuate the nominal acceleration environment and provide some isolation for microgravity science experiments. The g-LIMIT uses Lorentz (voice-coil) magnetic actuators to isolate a platform, for mounting science payloads, from the nominal acceleration environment. The system utilizes payload-acceleration, relative-position, and relative-orientation measurements in a feedback controller to accomplish the vibration isolation task. The controller provides current commands to six magnetic actuators, producing the required experiment isolation from the ISS acceleration environment. The present work documents the development of a candidate control law to meet the acceleration attenuation requirements for the g-LIMIT experiment platform. The controller design is developed using linear optimal control techniques for frequency-weighted H2 norms. Comparison of performance and robustness to plant uncertainty for this control design approach is included in the discussion. System performance is demonstrated in the presence of plant modeling error.

Optimal Control Design Using an H2 Method for the Glovebox Integrated Microgravity Isolation Technology (g-LIMIT)

NASA Technical Reports Server (NTRS)

Calhoun, Phillip C.; Hampton, R. David; Whorton, Mark S.

2001-01-01

The acceleration environment on the International Space Station (ISS) will likely exceed the requirements of many micro-gravity experiments. The Glovebox Integrated Microgravity Isolation Technology (g-LIMIT) is being built by the NASA Marshall Space Flight Center to attenuate the nominal acceleration environment and provide some isolation for micro-gravity science experiments. G-LIMIT uses Lorentz (voice-coil) magnetic actuators to isolate a platform for mounting science payloads from the nominal acceleration environment. The system utilizes payload acceleration, relative position, and relative orientation measurements in a feedback controller to accomplish the vibration isolation task. The controller provides current command to six magnetic actuators, producing the required experiment isolation from the ISS acceleration environment. This paper presents the development of a candidate control law to meet the acceleration attenuation requirements for the g-LIMIT experiment platform. The controller design is developed using linear optimal control techniques for both frequency-weighted H(sub 2) and H(sub infinity) norms. Comparison of the performance and robustness to plant uncertainty for these two optimal control design approaches are included in the discussion.

Single subject controlled experiments in aphasia: The science and the state of the science

PubMed Central

Thompson, Cynthia K.

2007-01-01

This paper discusses the use of single subject controlled experimental designs for investigating the effect of treatment for aphasia. A brief historical perspective is presented, followed by discussions of the advantages and disadvantages of single subject and group approaches, the basic requirements of single subject experimental research, and crucial considerations in design selection. In the final sections, results of reviews of published single subject controlled experiments are discussed, with emphasis on internal validity issues, the number of participants enrolled in published studies, operational specification of the dependent and independent variables, and reliability of measurement. Learning outcomes As a result of reading this paper, the participant will: (1) understand the mechanisms required for demonstration of internal and external validity using single subject controlled experimental designs, (2) become familiar with the basic requirements of single subject controlled experimental research, (3) understand the types of single subject controlled experimental designs that are the most appropriate for studying the effects of treatment for aphasia, and (4) become familiar with trends in the published aphasia treatment literature in which single subject controlled experimental designs have been used. PMID:16635494

Spectrally controlled interferometry for measurements of flat and spherical optics

NASA Astrophysics Data System (ADS)

Salsbury, Chase; Olszak, Artur G.

2017-10-01

Conventional interferometry is widely used to measure spherical and at surfaces with nanometer level precision but is plagued by back reflections. We describe a new method of isolating the measurement surface by controlling spectral properties of the source (Spectrally Controlled Interferometry - SCI). Using spectral modulation of the interferometer's source enables formation of localized fringes where the optical path difference is non-zero. As a consequence it becomes possible to form white-light like fringes in common path interferometers, such as the Fizeau. The proposed setup does not require mechanical phase shifting, resulting in simpler instruments and the ability to upgrade existing interferometers. Furthermore, it allows absolute measurement of distance, including radius of curvature of lenses in a single setup with possibility of improving the throughput and removing some modes of failure.

25 CFR 543.16 - What are the minimum internal controls for information technology?

Code of Federal Regulations, 2010 CFR

2010-04-01

... technology? 543.16 Section 543.16 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN... controls for information technology? (a) Physical security measures restricting access to agents, including... longer required. (2) In the event of remote access, the information technology employees must prepare a...

In vitro fracture resistance of three commercially available zirconia crowns for primary molars.

PubMed

Townsend, Janice A; Knoell, Patrick; Yu, Qingzhao; Zhang, Jian-Feng; Wang, Yapin; Zhu, Han; Beattie, Sean; Xu, Xiaoming

2014-01-01

The purpose of this study was to measure the fracture resistance of primary mandibular first molar zirconia crowns from three different manufacturers-EZ Pedo (EZP), NuSmile (NSZ), and Kinder Krowns (KK)-and compare it with the thickness of the zirconia crowns and the measured fracture resistance of preveneered stainless steel crowns (SSCs). The thickness of 20 zirconia crowns from three manufacturers were measured. The mean force required to fracture the crowns was determined. Preveneered NuSmile (NSW) SSCs were tested as a control. EZP crowns were significantly thicker in three of the six measured locations. The force required to fracture the EZP crown was significantly higher than that required for NSZ and KK. There was a positive correlation between fracture resistance and crown thickness in the mesial, distal, mesioocclusal, and distoocclusal dimensions. None of the zirconia crowns proved to be as resistant to fracture as the preveneered SSCs. Statistically significant differences were found among the forces required to fracture zirconia crowns by three different manufacturers. The increase in force correlated with crown thickness. The forces required to fracture the preveneered stainless steel crowns were greater than the forces required to fracture all manufacturers' zirconia crowns.

76 FR 10852 - Magnuson-Stevens Act Provisions; Fisheries of the Northeastern United States; Northeast...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-28

..., permitting restrictions, gear restrictions designed to minimize habitat impacts, and reporting requirements... requirement was previously approved for FY 2010 based upon the rationale that this measure was designed to... gillnet gear. This exemption was previously approved for FY 2010 because it is designed to control fishing...

30 CFR 250.420 - What well casing and cementing requirements must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Casing and Cementing Requirements § 250.420 What well casing and cementing... thereof. (2) The casing design must include safety measures that ensure well control during drilling and...

30 CFR 250.420 - What well casing and cementing requirements must I meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Casing and Cementing Requirements § 250.420 What well casing and cementing... casing design must include safety measures that ensure well control during drilling and safe operations...

30 CFR 250.420 - What well casing and cementing requirements must I meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Casing and Cementing Requirements § 250.420 What well casing and cementing... thereof. (2) The casing design must include safety measures that ensure well control during drilling and...

The Color-Word Interference Test and Its Relation to Performance Impairment under Auditory Distraction.

ERIC Educational Resources Information Center

Thackray, Richard I.; And Others

The ability to resist distraction is an important requirement for air traffic controllers. The study examined the relationship between performance on the Stroop color-word interference test (a suggested measure of distraction susceptibility) and impairment under auditory distraction on a task requiring the subject to generate random sequences of…

Using epidemiological information to develop effective integrated virus disease management strategies.

PubMed

Jones, Roger A C

2004-03-01

Virus diseases cause serious losses in yield and quality of cultivated plants worldwide. These losses and the resulting financial damage can be limited by controlling epidemics using measures that minimise virus infection sources or suppress virus spread. For each combination of virus, cultivated plant and production system, there is an 'economic threshold' above which the financial damage is sufficient to justify using such measures. However, individual measures used alone may bring only small benefits and they may become ineffective, especially over the long term. When diverse control measures that act in different ways are combined and used together, their effects are complementary resulting in far more effective overall control. Such experiences have led to the development of integrated management concepts for virus diseases that combine available host resistance, cultural, chemical and biological control measures. Selecting the ideal mix of measures for each pathosystem and production situation requires detailed knowledge of the epidemiology of the causal virus and the mode of action of each individual control measure so that diverse responses can be devised to meet the unique features of each of the different scenarios considered. The strategies developed must be robust and necessitate minimal extra expense, labour demands and disruption to standard practices. Examples of how epidemiological information can be used to develop effective integrated disease management (IDM) strategies for diverse situations are described. They involve circumstances where virus transmission from plant-to-plant occurs in four different ways: by contact, non-persistently or persistently by insect vectors, and by root-infecting fungi. The examples are: Subterranean clover mottle virus (SCMoV) (contact-transmitted) and Bean yellow mosaic virus (BYMV) (non-persistently aphid-transmitted) in annually self-regenerating clover pasture; three seed-borne viruses (all non-persistently aphid-transmitted) plots of pasture legume improvement programmes; Tomato spotted wilt virus (TSWV) (persistently thrips-transmitted) in vegetables in seedling nurseries, protected cropping or field systems; and lettuce big-vein disease (fungus-transmitted) in lettuce in seedling nursery, hydroponic, infested field or uninfested field situations. By describing the kinds of approaches required, this article is intended to help future research and extension programmes devise integrated disease management strategies that not only function effectively to diminish the losses caused by economically important plant virus diseases but also fulfill the requirement of being environmentally and socially responsible.

Cognitive performance in women with fibromyalgia: A case-control study.

PubMed

Pérez de Heredia-Torres, Marta; Huertas-Hoyas, Elisabet; Máximo-Bocanegra, Nuria; Palacios-Ceña, Domingo; Fernández-De-Las-Peñas, César

2016-10-01

This study aimed to evaluate the differences in cognitive skills between women with fibromyalgia and healthy women, and the correlations between functional independence and cognitive limitations. A cross-sectional study was performed. Twenty women with fibromyalgia and 20 matched controls participated. Outcomes included the Numerical Pain Rating Scale, the Functional Independence Measure, the Fibromyalgia Impact Questionnaire and Gradior © software. The Student's t-test and the Spearman's rho test were applied to the data. Women affected required a greater mean time (P < 0.020) and maximum time (P < 0.015) during the attention test than the healthy controls. In the memory test they displayed greater execution errors (P < 0.001), minimal time (P < 0.001) and mean time (P < 0.001) whereas, in the perception tests, they displayed a greater mean time (P < 0.009) and maximum time (P < 0.048). Correlations were found between the domains of the functional independence measure and the cognitive abilities assessed. Women with fibromyalgia exhibited a decreased cognitive ability compared to healthy controls, which negatively affected the performance of daily activities, such as upper limb dressing, feeding and personal hygiene. Patients required more time to perform activities requiring both attention and perception, decreasing their functional independence. Also, they displayed greater errors when performing activities requiring the use of memory. Occupational therapists treating women with fibromyalgia should consider the negative impact of possible cognitive deficits on the performance of daily activities and offer targeted support strategies. © 2016 Occupational Therapy Australia.

Industrial Photogrammetry - Accepted Metrology Tool or Exotic Niche

NASA Astrophysics Data System (ADS)

Bösemann, Werner

2016-06-01

New production technologies like 3D printing and other adaptive manufacturing technologies have changed the industrial manufacturing process, often referred to as next industrial revolution or short industry 4.0. Such Cyber Physical Production Systems combine virtual and real world through digitization, model building process simulation and optimization. It is commonly understood that measurement technologies are the key to combine the real and virtual worlds (eg. [Schmitt 2014]). This change from measurement as a quality control tool to a fully integrated step in the production process has also changed the requirements for 3D metrology solutions. Key words like MAA (Measurement Assisted Assembly) illustrate that new position of metrology in the industrial production process. At the same time it is obvious that these processes not only require more measurements but also systems to deliver the required information in high density in a short time. Here optical solutions including photogrammetry for 3D measurements have big advantages over traditional mechanical CMM's. The paper describes the relevance of different photogrammetric solutions including state of the art, industry requirements and application examples.

A low cost virtual reality system for home based rehabilitation of the arm following stroke: a randomised controlled feasibility trial

PubMed Central

Standen, PJ; Threapleton, K; Richardson, A; Connell, L; Brown, DJ; Battersby, S; Platts, F; Burton, A

2016-01-01

Objective: To assess the feasibility of conducting a randomised controlled trial of a home-based virtual reality system for rehabilitation of the arm following stroke. Design: Two group feasibility randomised controlled trial of intervention versus usual care. Setting: Patients’ homes. Participants: Patients aged 18 or over, with residual arm dysfunction following stroke and no longer receiving any other intensive rehabilitation. Interventions: Eight weeks’ use of a low cost home-based virtual reality system employing infra-red capture to translate the position of the hand into game play or usual care. Main measures: The primary objective was to collect information on the feasibility of a trial, including recruitment, collection of outcome measures and staff support required. Patients were assessed at three time points using the Wolf Motor Function Test, Nine-Hole Peg Test, Motor Activity Log and Nottingham Extended Activities of Daily Living. Results: Over 15 months only 47 people were referred to the team. Twenty seven were randomised and 18 (67%) of those completed final outcome measures. Sample size calculation based on data from the Wolf Motor Function Test indicated a requirement for 38 per group. There was a significantly greater change from baseline in the intervention group on midpoint Wolf Grip strength and two subscales of the final Motor Activity Log. Training in the use of the equipment took a median of 230 minutes per patient. Conclusions: To achieve the required sample size, a definitive home-based trial would require additional strategies to boost recruitment rates and adequate resources for patient support. PMID:27029939

Automatic pattern localization across layout database and photolithography mask

NASA Astrophysics Data System (ADS)

Morey, Philippe; Brault, Frederic; Beisser, Eric; Ache, Oliver; Röth, Klaus-Dieter

2016-03-01

Advanced process photolithography masks require more and more controls for registration versus design and critical dimension uniformity (CDU). The distribution of the measurement points should be distributed all over the whole mask and may be denser in areas critical to wafer overlay requirements. This means that some, if not many, of theses controls should be made inside the customer die and may use non-dedicated patterns. It is then mandatory to access the original layout database to select patterns for the metrology process. Finding hundreds of relevant patterns in a database containing billions of polygons may be possible, but in addition, it is mandatory to create the complete metrology job fast and reliable. Combining, on one hand, a software expertise in mask databases processing and, on the other hand, advanced skills in control and registration equipment, we have developed a Mask Dataprep Station able to select an appropriate number of measurement targets and their positions in a huge database and automatically create measurement jobs on the corresponding area on the mask for the registration metrology system. In addition, the required design clips are generated from the database in order to perform the rendering procedure on the metrology system. This new methodology has been validated on real production line for the most advanced process. This paper presents the main challenges that we have faced, as well as some results on the global performances.

Integrated identification, modeling and control with applications

NASA Astrophysics Data System (ADS)

Shi, Guojun

This thesis deals with the integration of system design, identification, modeling and control. In particular, six interdisciplinary engineering problems are addressed and investigated. Theoretical results are established and applied to structural vibration reduction and engine control problems. First, the data-based LQG control problem is formulated and solved. It is shown that a state space model is not necessary to solve this problem; rather a finite sequence from the impulse response is the only model data required to synthesize an optimal controller. The new theory avoids unnecessary reliance on a model, required in the conventional design procedure. The infinite horizon model predictive control problem is addressed for multivariable systems. The basic properties of the receding horizon implementation strategy is investigated and the complete framework for solving the problem is established. The new theory allows the accommodation of hard input constraints and time delays. The developed control algorithms guarantee the closed loop stability. A closed loop identification and infinite horizon model predictive control design procedure is established for engine speed regulation. The developed algorithms are tested on the Cummins Engine Simulator and desired results are obtained. A finite signal-to-noise ratio model is considered for noise signals. An information quality index is introduced which measures the essential information precision required for stabilization. The problems of minimum variance control and covariance control are formulated and investigated. Convergent algorithms are developed for solving the problems of interest. The problem of the integrated passive and active control design is addressed in order to improve the overall system performance. A design algorithm is developed, which simultaneously finds: (i) the optimal values of the stiffness and damping ratios for the structure, and (ii) an optimal output variance constrained stabilizing controller such that the active control energy is minimized. A weighted q-Markov COVER method is introduced for identification with measurement noise. The result is use to develop an iterative closed loop identification/control design algorithm. The effectiveness of the algorithm is illustrated by experimental results.

The physics of symbols: bridging the epistemic cut.

PubMed

Pattee, H H

2001-01-01

Evolution requires the genotype-phenotype distinction, a primeval epistemic cut that separates energy-degenerate, rate-independent genetic symbols from the rate-dependent dynamics of construction that they control. This symbol-matter or subject-object distinction occurs at all higher levels where symbols are related to a referent by an arbitrary code. The converse of control is measurement in which a rate-dependent dynamical state is coded into quiescent symbols. Non-integrable constraints are one necessary condition for bridging the epistemic cut by measurement, control, and coding. Additional properties of heteropolymer constraints are necessary for biological evolution.

Report: EPA’s Handling of a Proposed Alternative Method for Measuring Oil and Grease in Wastewater Met Requirements But Controls Need to Be Strengthened

EPA Pesticide Factsheets

Report #13-P-0317, July 11, 2013. EPA’s handling of the proposed alternative method for measuring oil and grease in wastewater (ASTM D7575) adhered to applicable laws, regulations, policies, procedures, and guidance.

Software quality assurance | News

Science.gov Websites

Measure was removed: "Sufficient level of detail in the requirements to develop test cases." ; This control measure was removed since the sufficient level of detail needed to develop test cases is recorded for all test cases. (Note: This is mandatory for applications graded with a High Quality Assurance

Short-term effects of goal-setting focusing on the life goal concept on subjective well-being and treatment engagement in subacute inpatients: a quasi-randomized controlled trial

PubMed Central

Ogawa, Tatsuya; Omon, Kyohei; Yuda, Tomohisa; Ishigaki, Tomoya; Imai, Ryota; Ohmatsu, Satoko; Morioka, Shu

2016-01-01

Objective: To investigate the short-term effects of the life goal concept on subjective well-being and treatment engagement, and to determine the sample size required for a larger trial. Design: A quasi-randomized controlled trial that was not blinded. Setting: A subacute rehabilitation ward. Subjects: A total of 66 patients were randomized to a goal-setting intervention group with the life goal concept (Life Goal), a standard rehabilitation group with no goal-setting intervention (Control 1), or a goal-setting intervention group without the life goal concept (Control 2). Interventions: The goal-setting intervention in the Life Goal and Control 2 was Goal Attainment Scaling. The Life Goal patients were assessed in terms of their life goals, and the hierarchy of goals was explained. The intervention duration was four weeks. Main measures: Patients were assessed pre- and post-intervention. The outcome measures were the Hospital Anxiety and Depression Scale, 12-item General Health Questionnaire, Pittsburgh Rehabilitation Participation Scale, and Functional Independence Measure. Results: Of the 296 potential participants, 66 were enrolled; Life Goal (n = 22), Control 1 (n = 22) and Control 2 (n = 22). Anxiety was significantly lower in the Life Goal (4.1 ±3.0) than in Control 1 (6.7 ±3.4), but treatment engagement was significantly higher in the Life Goal (5.3 ±0.4) compared with both the Control 1 (4.8 ±0.6) and Control 2 (4.9 ±0.5). Conclusions: The life goal concept had a short-term effect on treatment engagement. A sample of 31 patients per group would be required for a fully powered clinical trial. PMID:27496700

Reliability of a Cryoscopic Micro-Osmometer Using 15-µL Plasma Samples to Measure Hydration Status in Varied Environmental Conditions

ERIC Educational Resources Information Center

Scanlan, Aaron T.; Richter-Stretton, Gina L.; Madueno, Maria C.; Borges, Nattai R.; Fenning, Andrew S.

2017-01-01

Measurement of plasma osmolality (P[subscript osm]) remains popular for assessing hydration status in exercise science. However, a controlled reliability assessment of micro-osmometry using small sample volumes to measure Posm remains to be performed. This study aimed to examine the reliability of a cryoscopic micro-osmometer requiring 15-µL…

Oscillatory motion based measurement method and sensor for measuring wall shear stress due to fluid flow

DOEpatents

Armstrong, William D [Laramie, WY; Naughton, Jonathan [Laramie, WY; Lindberg, William R [Laramie, WY

2008-09-02

A shear stress sensor for measuring fluid wall shear stress on a test surface is provided. The wall shear stress sensor is comprised of an active sensing surface and a sensor body. An elastic mechanism mounted between the active sensing surface and the sensor body allows movement between the active sensing surface and the sensor body. A driving mechanism forces the shear stress sensor to oscillate. A measuring mechanism measures displacement of the active sensing surface relative to the sensor body. The sensor may be operated under periodic excitation where changes in the nature of the fluid properties or the fluid flow over the sensor measurably changes the amplitude or phase of the motion of the active sensing surface, or changes the force and power required from a control system in order to maintain constant motion. The device may be operated under non-periodic excitation where changes in the nature of the fluid properties or the fluid flow over the sensor change the transient motion of the active sensor surface or change the force and power required from a control system to maintain a specified transient motion of the active sensor surface.

Design and development of LED-based irregular leather area measuring machine

NASA Astrophysics Data System (ADS)

Adil, Rehan; Khan, Sarah Jamal

2012-01-01

Using optical sensor array, a precision motion control system in a conveyer follows the irregular shaped leather sheet to measure its surface area. In operation, irregular shaped leather sheet passes on conveyer belt and optical sensor array detects the leather sheet edge. In this way outside curvature of the leather sheet is detected and is then feed to the controller to measure its approximate area. Such system can measure irregular shapes, by neglecting rounded corners, ellipses etc. To minimize the error in calculating surface area of irregular curve to the above mentioned system, the motion control system only requires the footprint of the optical sensor to be small and the distance between the sensors is to be minimized. In the proposed technique surface area measurement of irregular shaped leather sheet is done by defining velocity and detecting position of the move. The motion controller takes the information and creates the necessary edge profile on point-to-point bases. As a result irregular shape of leather sheet is mapped and is then feed to the controller to calculate surface area.

Focus control enhancement and on-product focus response analysis methodology

NASA Astrophysics Data System (ADS)

Kim, Young Ki; Chen, Yen-Jen; Hao, Xueli; Samudrala, Pavan; Gomez, Juan-Manuel; Mahoney, Mark O.; Kamalizadeh, Ferhad; Hanson, Justin K.; Lee, Shawn; Tian, Ye

2016-03-01

With decreasing CDOF (Critical Depth Of Focus) for 20/14nm technology and beyond, focus errors are becoming increasingly critical for on-product performance. Current on product focus control techniques in high volume manufacturing are limited; It is difficult to define measurable focus error and optimize focus response on product with existing methods due to lack of credible focus measurement methodologies. Next to developments in imaging and focus control capability of scanners and general tool stability maintenance, on-product focus control improvements are also required to meet on-product imaging specifications. In this paper, we discuss focus monitoring, wafer (edge) fingerprint correction and on-product focus budget analysis through diffraction based focus (DBF) measurement methodology. Several examples will be presented showing better focus response and control on product wafers. Also, a method will be discussed for a focus interlock automation system on product for a high volume manufacturing (HVM) environment.

Measuring strategic control in artificial grammar learning.

PubMed

Norman, Elisabeth; Price, Mark C; Jones, Emma

2011-12-01

In response to concerns with existing procedures for measuring strategic control over implicit knowledge in artificial grammar learning (AGL), we introduce a more stringent measurement procedure. After two separate training blocks which each consisted of letter strings derived from a different grammar, participants either judged the grammaticality of novel letter strings with respect to only one of these two grammars (pure-block condition), or had the target grammar varying randomly from trial to trial (novel mixed-block condition) which required a higher degree of conscious flexible control. Random variation in the colour and font of letters was introduced to disguise the nature of the rule and reduce explicit learning. Strategic control was observed both in the pure-block and mixed-block conditions, and even among participants who did not realise the rule was based on letter identity. This indicated detailed strategic control in the absence of explicit learning. Copyright © 2011 Elsevier Inc. All rights reserved.

Assembly and Commissioning of a Liquid Argon Detector and Development of a Slow Control System for the COHERENT Experiment

NASA Astrophysics Data System (ADS)

Kaemingk, Michael; Cooper, Robert; Coherent Collaboration

2016-09-01

COHERENT is a collaboration whose goal is to measure coherent elastic neutrino-nucleus scattering (CEvNS). COHERENT plans to deploy a suite of detectors to measure the expected number-of-neutrons squared dependence of CEvNS at the Spallation Neutron Source at Oak Ridge National Laboratory. One of these detectors is a liquid argon detector which can measure these low energy nuclear recoil interactions. Ensuring optimal functionality requires the development of a slow control system to monitor and control various aspects, such as the temperature and pressure, of these detectors. Electronics manufactured by Beckhoff, Digilent, and Arduino among others are being used to create these slow control systems. This poster will generally discuss the assembly and commissioning of this CENNS-10 liquid argon detector at Indiana University and will feature work on the slow control systems.

Practical scheme for error control using feedback

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarovar, Mohan; Milburn, Gerard J.; Ahn, Charlene

2004-05-01

We describe a scheme for quantum-error correction that employs feedback and weak measurement rather than the standard tools of projective measurement and fast controlled unitary gates. The advantage of this scheme over previous protocols [for example, Ahn et al. Phys. Rev. A 65, 042301 (2001)], is that it requires little side processing while remaining robust to measurement inefficiency, and is therefore considerably more practical. We evaluate the performance of our scheme by simulating the correction of bit flips. We also consider implementation in a solid-state quantum-computation architecture and estimate the maximal error rate that could be corrected with current technology.

Correcting AUC for Measurement Error.

PubMed

Rosner, Bernard; Tworoger, Shelley; Qiu, Weiliang

2015-12-01

Diagnostic biomarkers are used frequently in epidemiologic and clinical work. The ability of a diagnostic biomarker to discriminate between subjects who develop disease (cases) and subjects who do not (controls) is often measured by the area under the receiver operating characteristic curve (AUC). The diagnostic biomarkers are usually measured with error. Ignoring measurement error can cause biased estimation of AUC, which results in misleading interpretation of the efficacy of a diagnostic biomarker. Several methods have been proposed to correct AUC for measurement error, most of which required the normality assumption for the distributions of diagnostic biomarkers. In this article, we propose a new method to correct AUC for measurement error and derive approximate confidence limits for the corrected AUC. The proposed method does not require the normality assumption. Both real data analyses and simulation studies show good performance of the proposed measurement error correction method.

64nm pitch metal1 double patterning metrology: CD and OVL control by SEMCD, image based overlay and diffraction based overlay

NASA Astrophysics Data System (ADS)

Ducoté, Julien; Dettoni, Florent; Bouyssou, Régis; Le-Gratiet, Bertrand; Carau, Damien; Dezauzier, Christophe

2015-03-01

Patterning process control of advanced nodes has required major changes over the last few years. Process control needs of critical patterning levels since 28nm technology node is extremely aggressive showing that metrology accuracy/sensitivity must be finely tuned. The introduction of pitch splitting (Litho-Etch-Litho-Etch) at 14FDSOInm node requires the development of specific metrologies to adopt advanced process control (for CD, overlay and focus corrections). The pitch splitting process leads to final line CD uniformities that are a combination of the CD uniformities of the two exposures, while the space CD uniformities are depending on both CD and OVL variability. In this paper, investigations of CD and OVL process control of 64nm minimum pitch at Metal1 level of 14FDSOI technology, within the double patterning process flow (Litho, hard mask etch, line etch) are presented. Various measurements with SEMCD tools (Hitachi), and overlay tools (KT for Image Based Overlay - IBO, and ASML for Diffraction Based Overlay - DBO) are compared. Metrology targets are embedded within a block instanced several times within the field to perform intra-field process variations characterizations. Specific SEMCD targets were designed for independent measurement of both line CD (A and B) and space CD (A to B and B to A) for each exposure within a single measurement during the DP flow. Based on those measurements correlation between overlay determined with SEMCD and with standard overlay tools can be evaluated. Such correlation at different steps through the DP flow is investigated regarding the metrology type. Process correction models are evaluated with respect to the measurement type and the intra-field sampling.

Generation of Requirements for Simulant Measurements. Revised, May 30, 2010

NASA Technical Reports Server (NTRS)

Rickman, Doug; Edmunson, Jennifer

2010-01-01

This document provides a formal, logical explanation of the parameters selected for the Figure of Merit algorithm used to evaluate lunar regolith simulant. The objectives, requirements, assumptions and analysis behind the parameters is provided. From NASA's objectives for lunar simulants a requirement is derived to verify and validate simulant performance versus lunar regolith. This requirement leads to a specification that comparative measurements be taken the same way on the regolith and the simulant. In turn this leads to a set of 9 criteria with which to evaluate comparative measurement. Many of the potential measurements of interest are not defensible under these criteria, for example many geotechnical properties of interest were not explicitly measured during Apollo and they can only be measured in situ on the Moon. A 2005 workshop identified 32 properties of major interest to users (Sibille Carpenter Schlagheck, and French, 2006). Virtually all of the properties are tightly constrained, though not predictable, if just four parameters are controlled. Three: composition, size and shape, are recognized as being definable at the particle level. The fourth, density, is a bulk property. In recent work a fifth parameter has been identified, which will need to be added to future releases of the Figure of Merit: spectroscopy.

Generation of Requirements for Simulant Measurements

NASA Technical Reports Server (NTRS)

Rickman, D. L.; Schrader, C. M.; Edmunson, J. E.

2010-01-01

This TM presents a formal, logical explanation of the parameters selected for the figure of merit (FoM) algorithm. The FoM algorithm is used to evaluate lunar regolith simulant. The objectives, requirements, assumptions, and analysis behind the parameters are provided. A requirement is derived to verify and validate simulant performance versus lunar regolith from NASA s objectives for lunar simulants. This requirement leads to a specification that comparative measurements be taken the same way on the regolith and the simulant. In turn, this leads to a set of nine criteria with which to evaluate comparative measurements. Many of the potential measurements of interest are not defensible under these criteria. For example, many geotechnical properties of interest were not explicitly measured during Apollo and they can only be measured in situ on the Moon. A 2005 workshop identified 32 properties of major interest to users. Virtually all of the properties are tightly constrained, though not predictable, if just four parameters are controlled. Three parameters (composition, size, and shape) are recognized as being definable at the particle level. The fourth parameter (density) is a bulk property. In recent work, a fifth parameter (spectroscopy) has been identified, which will need to be added to future releases of the FoM.

40 CFR 51.1000 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Benchmark RFP plan means the reasonable further progress plan that requires generally linear emission... Federally enforceable national, State, or local control measure that has been approved in the SIP and that...

40 CFR 51.1000 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Benchmark RFP plan means the reasonable further progress plan that requires generally linear emission... Federally enforceable national, State, or local control measure that has been approved in the SIP and that...

40 CFR 51.1000 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Benchmark RFP plan means the reasonable further progress plan that requires generally linear emission... Federally enforceable national, State, or local control measure that has been approved in the SIP and that...

40 CFR 51.1000 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Benchmark RFP plan means the reasonable further progress plan that requires generally linear emission... Federally enforceable national, State, or local control measure that has been approved in the SIP and that...

40 CFR 51.1000 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Benchmark RFP plan means the reasonable further progress plan that requires generally linear emission... Federally enforceable national, State, or local control measure that has been approved in the SIP and that...

Candidate control design metrics for an agile fighter

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.; Bailey, Melvin L.; Ostroff, Aaron J.

1991-01-01

Success in the fighter combat environment of the future will certainly demand increasing capability from aircraft technology. These advanced capabilities in the form of superagility and supermaneuverability will require special design techniques which translate advanced air combat maneuvering requirements into design criteria. Control design metrics can provide some of these techniques for the control designer. Thus study presents an overview of control design metrics and investigates metrics for advanced fighter agility. The objectives of various metric users, such as airframe designers and pilots, are differentiated from the objectives of the control designer. Using an advanced fighter model, metric values are documented over a portion of the flight envelope through piloted simulation. These metric values provide a baseline against which future control system improvements can be compared and against which a control design methodology can be developed. Agility is measured for axial, pitch, and roll axes. Axial metrics highlight acceleration and deceleration capabilities under different flight loads and include specific excess power measurements to characterize energy meneuverability. Pitch metrics cover both body-axis and wind-axis pitch rates and accelerations. Included in pitch metrics are nose pointing metrics which highlight displacement capability between the nose and the velocity vector. Roll metrics (or torsion metrics) focus on rotational capability about the wind axis.

Diffraction based overlay re-assessed

NASA Astrophysics Data System (ADS)

Leray, Philippe; Laidler, David; D'havé, Koen; Cheng, Shaunee

2011-03-01

In recent years, numerous authors have reported the advantages of Diffraction Based Overlay (DBO) over Image Based Overlay (IBO), mainly by comparison of metrology figures of merit such as TIS and TMU. Some have even gone as far as to say that DBO is the only viable overlay metrology technique for advanced technology nodes; 22nm and beyond. Typically the only reported drawback of DBO is the size of the required targets. This severely limits its effective use, when all critical layers of a product, including double patterned layers need to be measured, and in-die overlay measurements are required. In this paper we ask whether target size is the only limitation to the adoption of DBO for overlay characterization and control, or are there other metrics, which need to be considered. For example, overlay accuracy with respect to scanner baseline or on-product process overlay control? In this work, we critically re-assess the strengths and weaknesses of DBO for the applications of scanner baseline and on-product process layer overlay control. A comprehensive comparison is made to IBO. For on product process layer control we compare the performance on critical process layers; Gate, Contact and Metal. In particularly we focus on the response of the scanner to the corrections determined by each metrology technique for each process layer, as a measure of the accuracy. Our results show that to characterize an overlay metrology technique that is suitable for use in advanced technology nodes requires much more than just evaluating the conventional metrology metrics of TIS and TMU.

Reduction of User Interaction by Autonomy

NASA Technical Reports Server (NTRS)

Morfopoulos, Arin; McHenry, Michael; Matthies, Larry

2006-01-01

This paper describes experiments that quantify the improvement that autonomous behaviors enable in the amount of user interaction required to navigate a robot in urban environments. Many papers have discussed various ways to measure the absolute level of autonomy of a system; we measured the relative improvement of autonomous behaviors over teleoperation across multiple traverses of the same course. We performed four runs each on an 'easy' course and a 'hard' course, where half the runs were teleoperated and half used more autonomous behaviors. Statistics show 40-70% reductions in the amount of time the user interacts with the control station; however, with the behaviors tested, user attention remained on the control station even when he was not interacting. Reducing the need for attention will require better obstacle detection and avoidance and better absolute position estimation.

External Contamination Control of Attached Payloads on the International Space Station

NASA Technical Reports Server (NTRS)

Soares, Carlos E.; Mikatarian, Ronald R.; Olsen, Randy L.; Huang, Alvin Y.; Steagall, Courtney A.; Schmidl, William D.; Wright, Bruce D.; Koontz, Steven

2012-01-01

The International Space Station (ISS) is an on-orbit platform for science utilization in low Earth orbit with multiple sites for external payloads with exposure to the natural and induced environments. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. This paper describes the external contamination control requirements and integration process for externally mounted payloads on the ISS. The external contamination control requirements are summarized and a description of the integration and verification process is detailed to guide payload developers in the certification process of attached payloads on the vehicle. A description of the required data certification deliverables covers the characterization of contamination sources. Such characterization includes identification, usage and operational data for each class of contamination source. Classes of external contamination sources covered are vacuum exposed materials, sources of leakage, vacuum venting and thrusters. ISS system level analyses are conducted by the ISS Space Environments Team to certify compliance with external contamination control requirements. This paper also addresses the ISS induced contamination environment at attached payload sites, both at the requirements level as well as measurements made on ISS.

Personal customizing exercise with a wearable measurement and control unit.

PubMed

Wang, Zhihui; Kiryu, Tohru; Tamura, Naoki

2005-06-28

Recently, wearable technology has been used in various health-related fields to develop advanced monitoring solutions. However, the monitoring function alone cannot meet all the requirements of customizing machine-based exercise on an individual basis by relying on biosignal-based controls. We propose a new wearable unit design equipped with measurement and control functions to support the customization process. The wearable unit can measure the heart rate and electromyogram signals during exercise performance and output workload control commands to the exercise machines. The workload is continuously tracked with exercise programs set according to personally customized workload patterns and estimation results from the measured biosignals by a fuzzy control method. Exercise programs are adapted by relying on a computer workstation, which communicates with the wearable unit via wireless connections. A prototype of the wearable unit was tested together with an Internet-based cycle ergometer system to demonstrate that it is possible to customize exercise on an individual basis. We tested the wearable unit in nine people to assess its suitability to control cycle ergometer exercise. The results confirmed that the unit could successfully control the ergometer workload and continuously support gradual changes in physical activities. The design of wearable units equipped with measurement and control functions is an important step towards establishing a convenient and continuously supported wellness environment.

Assessment of a User Guide for One Semi-Automated Forces (OneSAF) Version 2.0

DTIC Science & Technology

2009-09-01

OneSAF uses a two-dimensional feature named a Plan View Display ( PVD ) as the primary graphical interface. The PVD replicates a map with a series...primary interface, the PVD is how the user watches the scenario unfold and requires the most interaction with the user. As seen in Table 3, all...participant indicated never using these seven map-related functions. Graphic control measures. Graphic control measures are applied to the PVD map to

Performance measurement: A tool for program control

NASA Technical Reports Server (NTRS)

Abell, Nancy

1994-01-01

Performance measurement is a management tool for planning, monitoring, and controlling as aspects of program and project management--cost, schedule, and technical requirements. It is a means (concept and approach) to a desired end (effective program planning and control). To reach the desired end, however, performance measurement must be applied and used appropriately, with full knowledge and recognition of its power and of its limitations--what it can and cannot do for the project manager. What is the potential of this management tool? What does performance measurement do that a traditional plan vs. actual technique cannot do? Performance measurement provides an improvement over the customary comparison of how much money was spent (actual cost) vs. how much was planned to be spent based on a schedule of activities (work planned). This commonly used plan vs. actual comparison does not allow one to know from the numerical data if the actual cost incurred was for work intended to be done.

Security of medical multimedia.

PubMed

Tzelepi, S; Pangalos, G; Nikolacopoulou, G

2002-09-01

The application of information technology to health care has generated growing concern about the privacy and security of medical information. Furthermore, data and communication security requirements in the field of multimedia are higher. In this paper we describe firstly the most important security requirements that must be fulfilled by multimedia medical data, and the security measures used to satisfy these requirements. These security measures are based mainly on modern cryptographic and watermarking mechanisms as well as on security infrastructures. The objective of our work is to complete this picture, exploiting the capabilities of multimedia medical data to define and implement an authorization model for regulating access to the data. In this paper we describe an extended role-based access control model by considering, within the specification of the role-permission relationship phase, the constraints that must be satisfied in order for the holders of the permission to use those permissions. The use of constraints allows role-based access control to be tailored to specifiy very fine-grained and flexible content-, context- and time-based access control policies. Other restrictions, such as role entry restriction also can be captured. Finally, the description of system architecture for a secure DBMS is presented.

Design and implementation of sensor systems for control of a closed-loop life support system

NASA Technical Reports Server (NTRS)

Alnwick, Leslie; Clark, Amy; Debs, Patricia; Franczek, Chris; Good, Tom; Rodrigues, Pedro

1989-01-01

The sensing and controlling needs for a Closed-Loop Life Support System (CLLSS) were investigated. The sensing needs were identified in five particular areas and the requirements were defined for workable sensors. The specific areas of interest were atmosphere and temperature, nutrient delivery, plant health, plant propagation and support, and solids processing. The investigation of atmosphere and temperature control focused on the temperature distribution within the growth chamber as well as the possibility for sensing other parameters such as gas concentration, pressure, and humidity. The sensing needs were studied for monitoring the solution level in a porous membrane material along with the requirements for measuring the mass flow rate in the delivery system. The causes and symptoms of plant disease were examined and the various techniques for sensing these health indicators were explored. The study of sensing needs for plant propagation and support focused on monitoring seed viability and measuring seed moisture content as well as defining the requirements for drying and storing the seeds. The areas of harvesting, food processing, and resource recycling, were covered with a main focus on the sensing possibilities for regulating the recycling process.

Analytical quality goals derived from the total deviation from patients' homeostatic set points, with a margin for analytical errors.

PubMed

Bolann, B J; Asberg, A

2004-01-01

The deviation of test results from patients' homeostatic set points in steady-state conditions may complicate interpretation of the results and the comparison of results with clinical decision limits. In this study the total deviation from the homeostatic set point is defined as the maximum absolute deviation for 95% of measurements, and we present analytical quality requirements that prevent analytical error from increasing this deviation to more than about 12% above the value caused by biology alone. These quality requirements are: 1) The stable systematic error should be approximately 0, and 2) a systematic error that will be detected by the control program with 90% probability, should not be larger than half the value of the combined analytical and intra-individual standard deviation. As a result, when the most common control rules are used, the analytical standard deviation may be up to 0.15 times the intra-individual standard deviation. Analytical improvements beyond these requirements have little impact on the interpretability of measurement results.

Spatial correlation in matter-wave interference as a measure of decoherence, dephasing, and entropy

NASA Astrophysics Data System (ADS)

Chen, Zilin; Beierle, Peter; Batelaan, Herman

2018-04-01

The loss of contrast in double-slit electron diffraction due to dephasing and decoherence processes is studied. It is shown that the spatial intensity correlation function of diffraction patterns can be used to distinguish between dephasing and decoherence. This establishes a measure of time reversibility that does not require the determination of coherence terms of the density matrix, while von Neumann entropy, another measure of time reversibility, does require coherence terms. This technique is exciting in view of the need to understand and control the detrimental experimental effect of contrast loss and for fundamental studies on the transition from the classical to the quantum regime.

Mark Tracking: Position/orientation measurements using 4-circle mark and its tracking experiments

NASA Technical Reports Server (NTRS)

Kanda, Shinji; Okabayashi, Keijyu; Maruyama, Tsugito; Uchiyama, Takashi

1994-01-01

Future space robots require position and orientation tracking with visual feedback control to track and capture floating objects and satellites. We developed a four-circle mark that is useful for this purpose. With this mark, four geometric center positions as feature points can be extracted from the mark by simple image processing. We also developed a position and orientation measurement method that uses the four feature points in our mark. The mark gave good enough image measurement accuracy to let space robots approach and contact objects. A visual feedback control system using this mark enabled a robot arm to track a target object accurately. The control system was able to tolerate a time delay of 2 seconds.

[Measurement and study report as a part of the control system for human safety and health protection against electromagnetic fields and electromagnetic radiation (0 Hz-300 GHz)].

PubMed

Aniołczyk, Halina

2007-01-01

The National Control System for safety and health protection against electromagnetic fields (EMF) and electromagnetic radiation (EMR) (0 Hz-300 GHz) is constantly analyzed in view of Directive 2004/40/EC. Reports on the effects of investments (at the designing stage or at the stage of looking for their localization) on the environment and measurement and study reports on the objects already existing or being put into operation are important elements of this system. These documents should meet both national and European Union's legislation requirements. The overriding goal of the control system is safety and health protection of humans against electromagnetic fields in the environment and in occupational settings. The author pays a particular attention to provisions made in directives issued by relevant ministers and to Polish standards, which should be documented in measurement and study reports published by the accredited laboratories and relating to the problems of human safety and health protection. Similar requirements are valid for the Reports. Therefore, along with measurement outcomes, the reports should include data on the EMF exposure classification at work-posts and the assessment of occupational risk resulting from EMF exposure or at least thorough data facilitating such a classification.

Microbial certification of the MER spacecraft

NASA Technical Reports Server (NTRS)

Schubert, W. W.; Arakelian, T.; Barengoltz, J. B.; Chough, N. G.; Chung, S. Y.; Law, J.; Kirschner, L.; Koukol, R. C.; Newlin, L. E.; Morales, F.

2003-01-01

We conclude in this paper that a combination of Dry Heat Microbrial Reduction and control measures during complex mechanical assembly processes can result in a total spore bioburden that meets requirements.

50 CFR 600.1002 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... moratorium on new entrants, restrictions on vessel upgrades, and other effort control measures, taking into account the full potential fishing capacity of the fleet; (2) Establish a specified or target total...

Contaminant levels, source strengths, and ventilation rates in California retail stores.

PubMed

Chan, W R; Cohn, S; Sidheswaran, M; Sullivan, D P; Fisk, W J

2015-08-01

This field study measured ventilation rates and indoor air quality in 21 visits to retail stores in California. Three types of stores, such as grocery, furniture/hardware stores, and apparel, were sampled. Ventilation rates measured using a tracer gas decay method exceeded the minimum requirement of California's Title 24 Standard in all but one store. Concentrations of volatile organic compounds (VOCs), ozone, and carbon dioxide measured indoors and outdoors were analyzed. Even though there was adequate ventilation according to standard, concentrations of formaldehyde and acetaldehyde exceeded the most stringent chronic health guidelines in many of the sampled stores. The whole-building emission rates of VOCs were estimated from the measured ventilation rates and the concentrations measured indoor and outdoor. Estimated formaldehyde emission rates suggest that retail stores would need to ventilate at levels far exceeding the current Title 24 requirement to lower indoor concentrations below California's stringent formaldehyde reference level. Given the high costs of providing ventilation, effective source control is an attractive alternative. Field measurements suggest that California retail stores were well ventilated relative to the minimum ventilation rate requirement specified in the Building Energy Efficiency Standards Title 24. Concentrations of formaldehyde found in retail stores were low relative to levels found in homes but exceeded the most stringent chronic health guideline. Looking ahead, California is mandating zero energy commercial buildings by 2030. To reduce the energy use from building ventilation while maintaining or even lowering formaldehyde in retail stores, effective formaldehyde source control measures are vitally important. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

33 CFR 274.7 - Authorization of pesticide use.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF DEFENSE PEST CONTROL PROGRAM FOR CIVIL WORKS PROJECTS Project Operation § 274.7 Authorization... unexpected outbreak of a pest requires control measures which are not according to the registered use, such... Engineer. An emergency will be deemed to exist when: (1) A pest outbreak has or is about to occur and no...

Field evaluations of emamectin benzoate for control of birch leafminer (Hymenoptera: Tenthredinidae) in Interior Alaska

Treesearch

Christopher J. Fettig; Roger E. Burnside; Christopher J. Hayes; Mark E. Schultz

2012-01-01

Ambermarked birch leafminer, Profenusa thomsoni (Konow) (Hymenoptera: Tenthredinidae), is an exotic, invasive pest of urban and wildland birch, Betula spp., in portions of North America. Extensive defoliation of ornamental birch in Alaska requires that suitable control measures be evaluated and developed. Based on previous work, we evaluated the...

A Multi-Sample Investigation of the Assessment and Locomotion Scales in a Population of Secondary School Students

ERIC Educational Resources Information Center

Hodis, Flaviu A.

2015-01-01

Understanding human motivation requires gauging individuals' strivings to be effective in controlling goal pursuits and establishing the truth about themselves and their experiences. Two constructs, assessment and locomotion, capture well truth and control strivings, respectively. The validation process of the instruments measuring assessment and…

Storage Capacity Explains Fluid Intelligence but Executive Control Does Not

ERIC Educational Resources Information Center

Chuderski, Adam; Taraday, Maciej; Necka, Edward; Smolen, Tomasz

2012-01-01

We examined whether fluid intelligence (Gf) is better predicted by the storage capacity of active memory or by the effectiveness of executive control. In two psychometric studies, we measured storage capacity with three kinds of task which required the maintenance of a visual array, the monitoring of simple relations among perceptually available…

40 CFR Appendix F to Part 112 - Facility-Specific Response Plan

Code of Federal Regulations, 2012 CFR

2012-07-01

... Prevention, Control, and Countermeasures (SPCC) Plan as required by 40 CFR 112.3. In these cases, owners or... sections for the non-transportation-related and transportation-related components, as described in § 112.20... of measure Response Action Actions Taken to Correct, Control or Mitigate Incident: Impact Number of...

40 CFR Appendix F to Part 112 - Facility-Specific Response Plan

Code of Federal Regulations, 2013 CFR

2013-07-01

... Prevention, Control, and Countermeasures (SPCC) Plan as required by 40 CFR 112.3. In these cases, owners or... sections for the non-transportation-related and transportation-related components, as described in § 112.20... of measure Response Action Actions Taken to Correct, Control or Mitigate Incident: Impact Number of...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... equivalency to EPA under this part must submit the request to EPA (via CDX) using e-PMN software. See 40 CFR 720.40(a)(2)(ii) for information on how to obtain e-PMN software. Support documents related to these...

A hydraulically driven colonoscope.

PubMed

Coleman, Stuart A; Tapia-Siles, Silvia C; Pakleppa, Markus; Vorstius, Jan B; Keatch, Robert P; Tang, Benjie; Cuschieri, Alfred

2016-10-01

Conventional colonoscopy requires a high degree of operator skill and is often painful for the patient. We present a preliminary feasibility study of an alternative approach where a self-propelled colonoscope is hydraulically driven through the colon. A hydraulic colonoscope which could be controlled manually or automatically was developed and assessed in a test bed modelled on the anatomy of the human colon. A conventional colonoscope was used by an experienced colonoscopist in the same test bed for comparison. Pressures and forces on the colon were measured during the test. The hydraulic colonoscope was able to successfully advance through the test bed in a comparable time to the conventional colonoscope. The hydraulic colonoscope reduces measured loads on artificial mesenteries, but increases intraluminal pressure compared to the colonoscope. Both manual and automatically controlled modes were able to successfully advance the hydraulic colonoscope through the colon. However, the automatic controller mode required lower pressures than manual control, but took longer to reach the caecum. The hydraulic colonoscope appears to be a viable device for further development as forces and pressures observed during use are comparable to those used in current clinical practice.

40 CFR 63.11585 - What are my notification, recordkeeping, and reporting requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the bag leak detector, parameter monitor, or CPMS. (ix) If a CPMS is used, the date of the latest...) Records of all inspections as required by § 63.11584(b) and pressure measurement device checks (if... according to § 63.11583(f). (viii) Records of particulate control device manufacturing specifications and...

40 CFR 63.5545 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... process unit such that the measurement is representative of control of the exhaust emissions (e.g., on or..., and validation check. (9) Except for redundant sensors, any device that is used to conduct an initial validation or accuracy audit of a CPMS must meet the accuracy requirements specified in paragraphs (f)(9)(i...

40 CFR 63.5545 - What are my monitoring installation, operation, and maintenance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... process unit such that the measurement is representative of control of the exhaust emissions (e.g., on or..., and validation check. (9) Except for redundant sensors, any device that is used to conduct an initial validation or accuracy audit of a CPMS must meet the accuracy requirements specified in paragraphs (f)(9)(i...

Plans for Assessing Contractor Performance for the Camp Lemonnier Base Operations Support Contract Needed Improvement

DTIC Science & Technology

2015-08-27

ensure the functional assessment plans ( FAP ) for the three services contained all contractor work requiring assessment, measurable performance...review the FAPs after development and revisions to the FAPs , and did not require additional controls over the contractor assessment process in an...revised as follows: • Business Management System B-14.3 was updated to require the contract officer representative conduct a FAP review to ensure

Measuring Workload Differences Between Short-term Memory and Long-term Memory Scenarios in a Simulated Flight Environment

NASA Technical Reports Server (NTRS)

Berg, S. L.; Sheridan, T. B.

1984-01-01

Four highly experienced Air Force pilots each flew four simulated flight scenarios. Two scenarios required a great deal of aircraft maneuvering. The other two scenarios involved less maneuvering, but required remembering a number of items. All scenarios were designed to be equaly challenging. Pilot's Subjective Ratings for Activity-level, Complexity, Difficulty, Stress, and Workload were higher for the manuevering scenarios than the memory scenarios. At a moderate workload level, keeping the pilots active resulted in better aircraft control. When required to monitor and remember items, aircraft control tended to decrease. Pilots tended to weigh information about the spatial positioning and performance of their aircraft more heavily than other items.

Control and prevention of tuberculosis in the United Kingdom: Code of Practice 2000

PubMed Central

Joint, T

2000-01-01

BACKGROUND—The guidelines on control and prevention of tuberculosis in the United Kingdom have been reviewed and updated.
METHODS—A subcommittee was appointed by the Joint Tuberculosis Committee (JTC) of the British Thoracic Society to revise the guidelines published in 1994 by the JTC, including representatives of the Royal College of Nursing, Public Health Medicine Environmental Group, and Medical Society for Study of Venereal Diseases. In preparing the revised guidelines the authors took account of new published evidence and graded the strength of evidence for their recommendations. The guidelines have been approved by the JTC and the Standards of Care Committee of the British Thoracic Society.
RECOMMENDATIONS—Tuberculosis services in each district should have staffing and resources to fulfil both the control and prevention recommendations in this document and to ensure adequate treatment monitoring. Notification of tuberculosis is required for surveillance and to initiate contact tracing (where appropriate). The following areas are discussed and recommendations made where appropriate: (1) public health law in relation to tuberculosis; (2) the organisational requirements for tuberculosis services; (3) measures for control of tuberculosis in hospitals, including segregation of patients; (4) the requirements for health care worker protection, including HIV infected health care workers; (5) measures for control of tuberculosis in prisons; (6) protection for other groups with potential exposure to tuberculosis; (7) awareness of the high rates of tuberculosis in the homeless together with local plans for detection and action; (8) detailed advice on contact tracing; (9) contact tracing required for close contacts of bovine tuberculosis; (10) management of tuberculosis in schools; (11) screening of new immigrants and how this should be performed; (12) outbreak contingency investigation; and (13) BCG vaccination and the management of positive reactors found in the schools programme.

 PMID:11050256

Passivity-based control with collision avoidance for a hub-beam spacecraft

NASA Astrophysics Data System (ADS)

Wen, Hao; Chen, Ti; Jin, Dongping; Hu, Haiyan

2017-01-01

For the application of robotically assembling large space structures, a feedback control law is synthesized for transitional and rotational maneuvers of a 'tug' spacecraft in order to transport a flexible element to a desired position without colliding with other space bodies. The flexible element is treated as a long beam clamped to the 'tug' spacecraft modelled as a rigid hub. First, the physical property of passivity of Euler-Lagrange system is exploited to design the position and attitude controllers by taking a simpler obstacle-free control problem into account. To reduce sensing and actuating requirements, the vibration modes of the beam appendage are supposed to be not directly measured and actuated on. Besides, the requirements of measuring velocities are removed with the aid of a dynamic extension technique. Second, the bounding boxes in the form of super-quadric surfaces are exploited to enclose the maximal extents of the obstacles and the hub-beam spacecraft. The collision avoidance between bounding boxes is achieved by applying additional repulsive force and torque to the spacecraft based on the method of artificial potential field. Finally, the effectiveness of proposed control scheme is numerically demonstrated via case studies.

The Validation by Measurement Theory of Proposed Object-Oriented Software Metrics

NASA Technical Reports Server (NTRS)

Neal, Ralph D.

1996-01-01

Moving software development into the engineering arena requires controllability, and to control a process, it must be measurable. Measuring the process does no good if the product is not also measured, i.e., being the best at producing an inferior product does not define a quality process. Also, not every number extracted from software development is a valid measurement. A valid measurement only results when we are able to verify that the number is representative of the attribute that we wish to measure. Many proposed software metrics are used by practitioners without these metrics ever having been validated, leading to costly but often useless calculations. Several researchers have bemoaned the lack of scientific precision in much of the published software measurement work and have called for validation of software metrics by measurement theory. This dissertation applies measurement theory to validate fifty proposed object-oriented software metrics.

High-throughput electrical characterization for robust overlay lithography control

NASA Astrophysics Data System (ADS)

Devender, Devender; Shen, Xumin; Duggan, Mark; Singh, Sunil; Rullan, Jonathan; Choo, Jae; Mehta, Sohan; Tang, Teck Jung; Reidy, Sean; Holt, Jonathan; Kim, Hyung Woo; Fox, Robert; Sohn, D. K.

2017-03-01

Realizing sensitive, high throughput and robust overlay measurement is a challenge in current 14nm and advanced upcoming nodes with transition to 300mm and upcoming 450mm semiconductor manufacturing, where slight deviation in overlay has significant impact on reliability and yield1). Exponentially increasing number of critical masks in multi-patterning lithoetch, litho-etch (LELE) and subsequent LELELE semiconductor processes require even tighter overlay specification2). Here, we discuss limitations of current image- and diffraction- based overlay measurement techniques to meet these stringent processing requirements due to sensitivity, throughput and low contrast3). We demonstrate a new electrical measurement based technique where resistance is measured for a macro with intentional misalignment between two layers. Overlay is quantified by a parabolic fitting model to resistance where minima and inflection points are extracted to characterize overlay control and process window, respectively. Analyses using transmission electron microscopy show good correlation between actual overlay performance and overlay obtained from fitting. Additionally, excellent correlation of overlay from electrical measurements to existing image- and diffraction- based techniques is found. We also discuss challenges of integrating electrical measurement based approach in semiconductor manufacturing from Back End of Line (BEOL) perspective. Our findings open up a new pathway for accessing simultaneous overlay as well as process window and margins from a robust, high throughput and electrical measurement approach.

Effect of N-Methyl-D-Aspartate Receptor Antagonist Dextromethorphan on Opioid Analgesia in Pediatric Intensive Care Unit

PubMed Central

Al Alem, Hala; Al Shehri, Ali; Al-Jeraisy, Majed

2016-01-01

Objective. Pain control is an essential goal in the management of critical children. Narcotics are the mainstay for pain control. Patients frequently need escalating doses of narcotics. In such cases an adjunctive therapy may be beneficial. Dextromethorphan (DM) is NMDA receptor antagonist and may prevent tolerance to narcotics; however, its definitive role is still unclear. We sought whether dextromethorphan addition could decrease the requirements of fentanyl to control pain in critical children. Design. Double-blind, randomized control trial (RCT). Setting. Pediatric multidisciplinary ICU in tertiary care center. Patients. Thirty-six pediatric patients 2–14 years of age in a multidisciplinary PICU requiring analgesia were randomized into dextromethorphan and placebo. The subjects in both groups showed similarity in most of the characteristics. Interventions. Subjects while receiving fentanyl for pain control received dextromethorphan or placebo through nasogastric/orogastric tubes for 96 hours. Pain was assessed using FLACC and faces scales. Measurements and Main Results. This study found no statistical significant difference in fentanyl requirements between subjects receiving dextromethorphan and those receiving placebo (p = 0.127). Conclusions. Dextromethorphan has no effect on opioid requirement for control of acute pain in children admitted with acute critical care illness in PICU. The registration number for this trial is NCT01553435. PMID:27867308

Effect of N-Methyl-D-Aspartate Receptor Antagonist Dextromethorphan on Opioid Analgesia in Pediatric Intensive Care Unit.

PubMed

Naeem, Mohammed; Al Alem, Hala; Al Shehri, Ali; Al-Jeraisy, Majed

2016-01-01

Objective . Pain control is an essential goal in the management of critical children. Narcotics are the mainstay for pain control. Patients frequently need escalating doses of narcotics. In such cases an adjunctive therapy may be beneficial. Dextromethorphan (DM) is NMDA receptor antagonist and may prevent tolerance to narcotics; however, its definitive role is still unclear. We sought whether dextromethorphan addition could decrease the requirements of fentanyl to control pain in critical children. Design . Double-blind, randomized control trial (RCT). Setting . Pediatric multidisciplinary ICU in tertiary care center. Patients . Thirty-six pediatric patients 2-14 years of age in a multidisciplinary PICU requiring analgesia were randomized into dextromethorphan and placebo. The subjects in both groups showed similarity in most of the characteristics. Interventions . Subjects while receiving fentanyl for pain control received dextromethorphan or placebo through nasogastric/orogastric tubes for 96 hours. Pain was assessed using FLACC and faces scales. Measurements and Main Results . This study found no statistical significant difference in fentanyl requirements between subjects receiving dextromethorphan and those receiving placebo ( p = 0.127). Conclusions . Dextromethorphan has no effect on opioid requirement for control of acute pain in children admitted with acute critical care illness in PICU. The registration number for this trial is NCT01553435.

Towards DMD-Based Estimation and Control of Flow Separation using an Array of Surface Pressure Sensors

NASA Astrophysics Data System (ADS)

Deem, Eric; Cattafesta, Louis; Zhang, Hao; Rowley, Clancy

2016-11-01

Closed-loop control of flow separation requires the spatio-temporal states of the flow to be fed back through the controller in real time. Previously, static and dynamic estimation methods have been employed that provide reduced-order model estimates of the POD-coefficients of the flow velocity using surface pressure measurements. However, this requires a "learning" dataset a priori. This approach is effective as long as the dynamics during control do not stray from the learning dataset. Since only a few dynamical features are required for feedback control of flow separation, many of the details provided by full-field snapshots are superfluous. This motivates a state-observation technique that extracts key dynamical features directly from surface pressure, without requiring PIV snapshots. The results of identifying DMD modes of separated flow through an array of surface pressure sensors in real-time are presented. This is accomplished by employing streaming DMD "on the fly" to surface pressure snapshots. These modal characteristics exhibit striking similarities to those extracted from PIV data and the pressure field obtained via solving Poisson's equation. Progress towards closed-loop separation control based on the dynamic modes of surface pressure will be discussed. Supported by AFOSR Grant FA9550-14-1-0289.

40 CFR 1045.115 - What other requirements apply?

Code of Federal Regulations, 2014 CFR

2014-07-01

... area networks. Your broadcasting protocol must allow for valid measurements using the field-testing... information broadcast by an engine's on-board computers and electronic control modules. If you broadcast a...

Implementing the new HEDIS hypertension performance measure.

PubMed

Sennett, C

2000-04-01

There is a problem with blood pressure control in the United States--a problem with significant implications for the health and welfare of the populace. This problem is bigger than managed care, but managed care organizations have both unique opportunities and unique obligations to address it. NCQA has responded to this problem, and to the opportunity for better care implicit in it, by introducing into HEDIS a measure that focuses on hypertension control. This measure will add pressure to health plans to address the problem of hypertension control, but it also will create the opportunity for positive recognition for those plans that succeed. The HEDIS hypertension measure is well grounded in both the science of medicine and the science of measurement. But HEDIS measurement alone will not create change. To effect change will require analysis of the problems that limit the delivery of effective care to patients with hypertension. It will require measurement of the success of the key processes of care upon which effective care depends. And it will require response--rational, focused, and operationally effective. These, in turn, will challenge key managers in health plans. Medical directors will have to influence provider behavior. Pharmacy directors will have to leverage pharmacy resources to support efforts to change provider and enrollee behaviors. And QA directors will have to manage a challenging set of measurement activities, from which plans' efforts to improve will be launched. The next few years will not be easy--demands for improvement increase annually, and resources are every year more scarce. Yet the goal is worth the struggle--to transform an industry that the public perceives to be interested in limiting care into one that the public turns to for assurance that care represents high value. Responding effectively to the HEDIS hypertension measure creates a unique opportunity for managed care--to demonstrate to the public that managed care is leading national efforts to improve quality for 50 million Americans needlessly at risk for heart disease and stroke, and in doing so, to demonstrate its commitment to health maintenance--the very foundation of managed care.

Autonomous Underwater Munitions and Explosives of Concern Detection System

DTIC Science & Technology

2015-03-01

Field Magnetometer ......................................................................... 19 5.3.2 Fluxgate Compass...through the vehicle control system. Magnetic measurements are sampled at 10 Hz. 5.3.2 Fluxgate Compass Located in the magnetometer module pressure...pitch, and roll) from the fluxgate compass and the total field magnetometer measurements are required for processing into the MagComp compensation

49 CFR 192.487 - Remedial measures: Distribution lines other than cast iron or ductile iron lines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... STANDARDS Requirements for Corrosion Control § 192.487 Remedial measures: Distribution lines other than cast iron or ductile iron lines. (a) General corrosion. Except for cast iron or ductile iron pipe, each... engineering tests and analyses show can permanently restore the serviceability of the pipe. Corrosion pitting...

49 CFR 192.487 - Remedial measures: Distribution lines other than cast iron or ductile iron lines.

Code of Federal Regulations, 2013 CFR

2013-10-01

... STANDARDS Requirements for Corrosion Control § 192.487 Remedial measures: Distribution lines other than cast iron or ductile iron lines. (a) General corrosion. Except for cast iron or ductile iron pipe, each... engineering tests and analyses show can permanently restore the serviceability of the pipe. Corrosion pitting...

49 CFR 192.487 - Remedial measures: Distribution lines other than cast iron or ductile iron lines.

Code of Federal Regulations, 2012 CFR

2012-10-01

... STANDARDS Requirements for Corrosion Control § 192.487 Remedial measures: Distribution lines other than cast iron or ductile iron lines. (a) General corrosion. Except for cast iron or ductile iron pipe, each... engineering tests and analyses show can permanently restore the serviceability of the pipe. Corrosion pitting...

49 CFR 192.487 - Remedial measures: Distribution lines other than cast iron or ductile iron lines.

Code of Federal Regulations, 2014 CFR

2014-10-01

... STANDARDS Requirements for Corrosion Control § 192.487 Remedial measures: Distribution lines other than cast iron or ductile iron lines. (a) General corrosion. Except for cast iron or ductile iron pipe, each... engineering tests and analyses show can permanently restore the serviceability of the pipe. Corrosion pitting...

40 CFR Table 3 to Subpart Lllll of... - Requirements for Performance Tests a,b

Code of Federal Regulations, 2011 CFR

2011-07-01

..., THC destruction efficiency, THC outlet concentration, or combustion efficiency standards, the sampling... combustion efficiency or THC standards a. Measure the concentration of carbon dioxideb. Measure the... method 25A in appendix A to part 60 of this chapter 10. Each control device used to comply with the THC...

40 CFR Table 3 to Subpart Lllll of... - Requirements for Performance Tests a,b

Code of Federal Regulations, 2012 CFR

2012-07-01

..., THC destruction efficiency, THC outlet concentration, or combustion efficiency standards, the sampling... combustion efficiency or THC standards a. Measure the concentration of carbon dioxideb. Measure the... method 25A in appendix A to part 60 of this chapter 10. Each control device used to comply with the THC...

40 CFR Table 3 to Subpart Lllll of... - Requirements for Performance Tests a,b

Code of Federal Regulations, 2010 CFR

2010-07-01

..., THC destruction efficiency, THC outlet concentration, or combustion efficiency standards, the sampling... combustion efficiency or THC standards a. Measure the concentration of carbon dioxideb. Measure the... method 25A in appendix A to part 60 of this chapter 10. Each control device used to comply with the THC...

40 CFR Table 3 to Subpart Lllll of... - Requirements for Performance Tests a b

Code of Federal Regulations, 2014 CFR

2014-07-01

..., THC destruction efficiency, THC outlet concentration, or combustion efficiency standards, the sampling... combustion efficiency or THC standards a. Measure the concentration of carbon dioxideb. Measure the... method 25A in appendix A to part 60 of this chapter 10. Each control device used to comply with the THC...

40 CFR Table 3 to Subpart Lllll of... - Requirements for Performance Tests a,b

Code of Federal Regulations, 2013 CFR

2013-07-01

..., THC destruction efficiency, THC outlet concentration, or combustion efficiency standards, the sampling... combustion efficiency or THC standards a. Measure the concentration of carbon dioxideb. Measure the... method 25A in appendix A to part 60 of this chapter 10. Each control device used to comply with the THC...

Speed Isn't Everything: Complex Processing Speed Measures Mask Individual Differences and Developmental Changes in Executive Control

ERIC Educational Resources Information Center

Cepeda, Nicholas J.; Blackwell, Katharine A.; Munakata, Yuko

2013-01-01

The rate at which people process information appears to influence many aspects of cognition across the lifespan. However, many commonly accepted measures of "processing speed" may require goal maintenance, manipulation of information in working memory, and decision-making, blurring the distinction between processing speed and executive…

Image Tiling for Profiling Large Objects

NASA Technical Reports Server (NTRS)

Venkataraman, Ajit; Schock, Harold; Mercer, Carolyn R.

1992-01-01

Three dimensional surface measurements of large objects arc required in a variety of industrial processes. The nature of these measurements is changing as optical instruments arc beginning to replace conventional contact probes scanned over the objects. A common characteristic of the optical surface profilers is the trade off between measurement accuracy and field of view. In order to measure a large object with high accuracy, multiple views arc required. An accurate transformation between the different views is needed to bring about their registration. In this paper, we demonstrate how the transformation parameters can be obtained precisely by choosing control points which lie in the overlapping regions of the images. A good starting point for the transformation parameters is obtained by having a knowledge of the scanner position. The selection of the control points arc independent of the object geometry. By successively recording multiple views and obtaining transformation with respect to a single coordinate system, a complete physical model of an object can be obtained. Since all data arc in the same coordinate system, it can thus be used for building automatic models for free form surfaces.

A computer-controlled apparatus for Seebeck inhomogeneity testing of sheathed thermocouples

NASA Technical Reports Server (NTRS)

Burkett, Cecil G., Jr.; Bauserman, Willard A., Jr.

1993-01-01

Mineral-insulated metal-sheathed (MIMS) thermocouple assemblies are used throughout industry and research facilities as a method of temperature measurement where requirements for either harsh environmental conditions exist, or where rigidity of the measurement probe is required. Seebeck inhomogeneity is the abnormal variation of the Seebeck coefficient from point to point in a material. It is not disclosed in conventional calibration. A standardized method of measuring thermoelectric inhomogeneity along the thermocouple probe length is not available. Therefore, calibration for sheathed probes normally does not include testing of probe inhomogeneity. The measurement accuracy would be severely impacted if significant inhomogeneity and a temperature gradient were present in the same region of the probe. A computer-controlled system for determining inhomogeneities was designed, fabricated, and tested. This system provides an accurate method for the identification of the location of inhomogeneity along the length of a sheathed thermocouple and for the quantification of the inhomogeneity. This paper will discuss the apparatus and procedure used to perform these tests and will present data showing tests performed on sheathed thermocouple probes.

Lessons Learned "Establishing an Electrically Safe Work Condition" Specifically related to Racking Electrical Breakers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, Tommy Robert; Romero, Philbert Roland; Garcia, Samuel Anthony

During low voltage electrical equipment maintenance, a bad breaker was identified. The breaker was racked out from the substation cubicle without following the hazardous energy control process identified in the Integrated Work Document (IWD). The IWD required the substation to be in an electrically safe work condition prior to racking the breaker. Per NFPA 70E requirements, electrical equipment shall be put into an electrically safe work condition before an employee performs work on or interacts with equipment in a manner that increases the likelihood of creating an arc flash. Racking in or out a breaker on an energized bus maymore » increase the likelihood of creating an arc flash dependent on equipment conditions. A thorough risk assessment must be performed prior to performing such a task. The risk assessment determines the risk control measures to be put in place prior to performing the work. Electrical Safety Officers (ESO) can assist in performing risk assessments and incorporating risk control measures.« less

Active Control of Separation From the Flap of a Supercritical Airfoil

NASA Technical Reports Server (NTRS)

Melton, LaTunia Pack; Yao, Chung-Sheng; Seifert, Avi

2006-01-01

Zero-mass-flux periodic excitation was applied at several regions on a simplified high-lift system to delay the occurrence of flow separation. The NASA Energy Efficient Transport (EET) supercritical airfoil was equipped with a 15% chord simply hinged leading edge flap and a 25% chord simply hinged trailing edge flap. Detailed flow features were measured in an attempt to identify optimal actuator placement. The measurements included steady and unsteady model and tunnel wall pressures, wake surveys, arrays of surface hot-films, flow visualization, and particle image velocimetry (PIV). The current paper describes the application of active separation control at several locations on the deflected trailing edge flap. High frequency (F(+) approximately equal to 10) and low frequency amplitude modulation (F(+) sub AM approximately equal to 1) of the high frequency excitation were used for control. It was noted that the same performance gains were obtained with amplitude modulation and required only 30% of the momentum input required by pure sine excitation.

A Computational Framework to Control Verification and Robustness Analysis

NASA Technical Reports Server (NTRS)

Crespo, Luis G.; Kenny, Sean P.; Giesy, Daniel P.

2010-01-01

This paper presents a methodology for evaluating the robustness of a controller based on its ability to satisfy the design requirements. The framework proposed is generic since it allows for high-fidelity models, arbitrary control structures and arbitrary functional dependencies between the requirements and the uncertain parameters. The cornerstone of this contribution is the ability to bound the region of the uncertain parameter space where the degradation in closed-loop performance remains acceptable. The size of this bounding set, whose geometry can be prescribed according to deterministic or probabilistic uncertainty models, is a measure of robustness. The robustness metrics proposed herein are the parametric safety margin, the reliability index, the failure probability and upper bounds to this probability. The performance observed at the control verification setting, where the assumptions and approximations used for control design may no longer hold, will fully determine the proposed control assessment.

Air-condition Control System of Weaving Workshop Based on LabVIEW

NASA Astrophysics Data System (ADS)

Song, Jian

The project of air-condition measurement and control system based on LabVIEW is put forward for the sake of controlling effectively the environmental targets in the weaving workshop. In this project, which is based on the virtual instrument technology and in which LabVIEW development platform by NI is adopted, the system is constructed on the basis of the virtual instrument technology. It is composed of the upper PC, central control nodes based on CC2530, sensor nodes, sensor modules and executive device. Fuzzy control algorithm is employed to achieve the accuracy control of the temperature and humidity. A user-friendly man-machine interaction interface is designed with virtual instrument technology at the core of the software. It is shown by experiments that the measurement and control system can run stably and reliably and meet the functional requirements for controlling the weaving workshop.

Instrumentation and control of harmonic oscillators via a single-board microprocessor-FPGA device.

PubMed

Picone, Rico A R; Davis, Solomon; Devine, Cameron; Garbini, Joseph L; Sidles, John A

2017-04-01

We report the development of an instrumentation and control system instantiated on a microprocessor-field programmable gate array (FPGA) device for a harmonic oscillator comprising a portion of a magnetic resonance force microscope. The specific advantages of the system are that it minimizes computation, increases maintainability, and reduces the technical barrier required to enter the experimental field of magnetic resonance force microscopy. Heterodyne digital control and measurement yields computational advantages. A single microprocessor-FPGA device improves system maintainability by using a single programming language. The system presented requires significantly less technical expertise to instantiate than the instrumentation of previous systems, yet integrity of performance is retained and demonstrated with experimental data.

Instrumentation and control of harmonic oscillators via a single-board microprocessor-FPGA device

NASA Astrophysics Data System (ADS)

Picone, Rico A. R.; Davis, Solomon; Devine, Cameron; Garbini, Joseph L.; Sidles, John A.

2017-04-01

We report the development of an instrumentation and control system instantiated on a microprocessor-field programmable gate array (FPGA) device for a harmonic oscillator comprising a portion of a magnetic resonance force microscope. The specific advantages of the system are that it minimizes computation, increases maintainability, and reduces the technical barrier required to enter the experimental field of magnetic resonance force microscopy. Heterodyne digital control and measurement yields computational advantages. A single microprocessor-FPGA device improves system maintainability by using a single programming language. The system presented requires significantly less technical expertise to instantiate than the instrumentation of previous systems, yet integrity of performance is retained and demonstrated with experimental data.

An on-line monitoring system for navigation equipment

NASA Astrophysics Data System (ADS)

Wang, Bo; Yang, Ping; Liu, Jing; Yang, Zhengbo; Liang, Fei

2017-10-01

Civil air navigation equipment is the most important infrastructure of Civil Aviation, which is closely related to flight safety. In addition to regular flight inspection, navigation equipment's patrol measuring, maintenance measuring, running measuring under special weather conditions are the important means of ensuring aviation flight safety. According to the safety maintenance requirements of Civil Aviation Air Traffic Control navigation equipment, this paper developed one on-line monitoring system with independent intellectual property rights for navigation equipment, the system breakthroughs the key technologies of measuring navigation equipment on-line including Instrument Landing System (ILS) and VHF Omni-directional Range (VOR), which also meets the requirements of navigation equipment ground measurement set by the ICAO DOC 8071, it provides technical means of the ground on-line measurement for navigation equipment, improves the safety of navigation equipment operation, and reduces the impact of measuring navigation equipment on airport operation.

Guidance and Control System for a Satellite Constellation

NASA Technical Reports Server (NTRS)

Bryson, Jonathan Lamar; Cox, James; Mays, Paul Richard; Neidhoefer, James Christian; Ephrain, Richard

2010-01-01

A distributed guidance and control algorithm was developed for a constellation of satellites. The system repositions satellites as required, regulates satellites to desired orbits, and prevents collisions. 1. Optimal methods are used to compute nominal transfers from orbit to orbit. 2. Satellites are regulated to maintain the desired orbits once the transfers are complete. 3. A simulator is used to predict potential collisions or near-misses. 4. Each satellite computes perturbations to its controls so as to increase any unacceptable distances of nearest approach to other objects. a. The avoidance problem is recast in a distributed and locally-linear form to arrive at a tractable solution. b. Plant matrix values are approximated via simulation at each time step. c. The Linear Quadratic Gaussian (LQG) method is used to compute perturbations to the controls that will result in increased miss distances. 5. Once all danger is passed, the satellites return to their original orbits, all the while avoiding each other as above. 6. The delta-Vs are reasonable. The controller begins maneuvers as soon as practical to minimize delta-V. 7. Despite the inclusion of trajectory simulations within the control loop, the algorithm is sufficiently fast for available satellite computer hardware. 8. The required measurement accuracies are within the capabilities of modern inertial measurement devices and modern positioning devices.

Measuring coercive control: what can we learn from national population surveys?

PubMed

Myhill, Andy

2015-03-01

Numerous academic studies point to gender symmetry in the prevalence of intimate partner violence (IPV). Many of these studies report findings from surveys with small and/or unrepresentative samples that have insufficient questions to differentiate adequately between different types of abuse. Data from a large, nationally representative survey suggest that, while the prevalence of situational violence is fairly symmetrical, coercive controlling abuse is highly gendered, with women overwhelmingly the victims. The authors conclude that more comprehensive measures are required in national surveys that consider a wider range of controlling behaviors as well as the meaning and impact of abuse. © The Author(s) 2015.

Creosote bush (Larrea tridentata) resin increases water demands and reduces energy availability in desert woodrats (Neotoma lepida).

PubMed

Mangione, Antonio M; Dearing, M Denise; Karasov, William H

2004-07-01

Although many plant secondary compounds are known to have serious consequences for herbivores, the costs of processing them are generally unknown. Two potential costs of ingestion and detoxification of secondary compounds are elevation of the minimum drinking water requirement and excretion of energetically expensive metabolites (i.e., glucuronides) in the urine. To address these impacts, we studied the costs of ingestion of resin from creosote bush (Larrea tridentata) on desert woodrats (Neotoma lepida). The following hypotheses were tested: ingestion of creosote resin by woodrats (1) increases minimum water requirement and (2) reduces energy available by increasing fecal and urinary energy losses. We tested the first hypothesis, by measuring the minimum water requirement of woodrats fed a control diet with and without creosote resin. Drinking water was given in decreasing amounts until woodrats could no longer maintain constant body mass. In two separate experiments, the minimum drinking water requirement of woodrats fed resin was higher than that of controls by 18-30% (about 1-1.7 ml/d). We tested several potential mechanisms of increased water loss associated with the increase in water requirement. The rate of fecal water loss was higher in woodrats consuming resin. Neither urinary water nor evaporative water loss was affected by ingestion of resin. Hypothesis 2 was tested by measuring energy fluxes of woodrats consuming control vs. resin-treated diets. Woodrats on a resin diet had higher urinary energy losses and, thus, metabolized a lower proportion of the dietary energy than did woodrats on control diet. Fecal energy excretion was not affected by resin. The excretion of glucuronic acid represented almost half of the energy lost as a consequence of resin ingestion. The increased water requirement and energy losses of woodrats consuming a diet with resin could have notable ecological consequences.

Real-time optical fiber digital speckle pattern interferometry for industrial applications

NASA Astrophysics Data System (ADS)

Chan, Robert K.; Cheung, Y. M.; Lo, C. H.; Tam, T. K.

1997-03-01

There is current interest, especially in the industrial sector, to use the digital speckle pattern interferometry (DSPI) technique to measure surface stress. Indeed, many publications in the subject are evident of the growing interests in the field. However, to bring the technology to industrial use requires the integration of several emerging technologies, viz. optics, feedback control, electronics, imaging processing and digital signal processing. Due to the highly interdisciplinary nature of the technique, successful implementation and development require expertise in all of the fields. At Baptist University, under the funding of a major industrial grant, we are developing the technology for the industrial sector. Our system fully exploits optical fibers and diode lasers in the design to enable practical and rugged systems suited for industrial applications. Besides the development in optics, we have broken away from the reliance of a microcomputer PC platform for both image capture and processing, and have developed a digital signal processing array system that can handle simultaneous and independent image capture/processing with feedback control. The system, named CASPA for 'cascadable architecture signal processing array,' is a third generation development system that utilizes up to 7 digital signal processors has proved to be a very powerful system. With our CASPA we are now in a better position to developing novel optical measurement systems for industrial application that may require different measurement systems to operate concurrently and requiring information exchange between the systems. Applications in mind such as simultaneous in-plane and out-of-plane DSPI image capture/process, vibrational analysis with interactive DSPI and phase shifting control of optical systems are a few good examples of the potentials.

Direct measurement of the rates of synthesis of plasma proteins in control subjects and patients with gastrointestinal protein loss

PubMed Central

Wochner, R. Dean; Weissman, Sherman M.; Waldmann, Thomas A.; Houston, Delores; Berlin, Nathaniel I.

1968-01-01

The guanido carbon of hepatic arginine is the common precursor of urea and of the arginine of plasma proteins synthesized in the liver. It is possible to measure the momentary synthetic rates of plasma proteins by “pulse labeling” this arginine pool with bicarbonate-14C. In the current study, this method has been adapted in order to use urinary urea data and was applied to control subjects and patients with gastrointestinal protein loss. The assumptions required for this determination are discussed. There was close agreement between albumin synthetic rates measured by this method and albumin catabolic rates derived from simultaneous albumin-131I studies, supporting the validity of the method and suggesting that there is relatively little fluctuation in the rate of albumin synthesis from time to time. The albumin synthetic rates in six control subjects averaged 5.8 mg/kg per hr, while those of five patients with gastrointestinal protein loss averaged 7.2 mg/kg per hr. Thus in these patients, there was relatively little acceleration of albumin synthesis in response to continued loss of plasma proteins into the gastrointestinal tract. Fibrinogen synthetic rates averaged 1.9 mg/kg per hr in five control subjects and 3.2 mg/kg per hr in five patients with gastrointestinal protein loss. Transferrin synthetic rates exhibited considerable individual variation in both groups and averaged 0.24 mg/kg per hr in four control subjects and 0.31 mg/kg per hr in five patients with gastrointestinal protein loss. The method employed in this study offers several advantages in studying plasma protein metabolism. It provides a direct measurement of protein synthesis, applicable to several proteins simultaneously, does not require a long-term steady state in the metabolism of the proteins, and is capable of measuring short-term fluctuations in synthetic rates. Therefore, this approach is applicable to the investigation of the physiological factors controlling the rates of synthesis for plasma proteins. PMID:5239039

Combining control input with flight path data to evaluate pilot performance in transport aircraft.

PubMed

Ebbatson, Matt; Harris, Don; Huddlestone, John; Sears, Rodney

2008-11-01

When deriving an objective assessment of piloting performance from flight data records, it is common to employ metrics which purely evaluate errors in flight path parameters. The adequacy of pilot performance is evaluated from the flight path of the aircraft. However, in large jet transport aircraft these measures may be insensitive and require supplementing with frequency-based measures of control input parameters. Flight path and control input data were collected from pilots undertaking a jet transport aircraft conversion course during a series of symmetric and asymmetric approaches in a flight simulator. The flight path data were analyzed for deviations around the optimum flight path while flying an instrument landing approach. Manipulation of the flight controls was subject to analysis using a series of power spectral density measures. The flight path metrics showed no significant differences in performance between the symmetric and asymmetric approaches. However, control input frequency domain measures revealed that the pilots employed highly different control strategies in the pitch and yaw axes. The results demonstrate that to evaluate pilot performance fully in large aircraft, it is necessary to employ performance metrics targeted at both the outer control loop (flight path) and the inner control loop (flight control) parameters in parallel, evaluating both the product and process of a pilot's performance.

Uniaxial three-dimensional shape measurement with multioperation modes for different modulation algorithms

NASA Astrophysics Data System (ADS)

Jing, Hailong; Su, Xianyu; You, Zhisheng

2017-03-01

A uniaxial three-dimensional shape measurement system with multioperation modes for different modulation algorithms is proposed. To provide a general measurement platform that satisfies the specific measurement requirements in different application scenarios, a measuring system with multioperation modes based on modulation measuring profilometry (MMP) is presented. Unlike the previous solutions, vertical scanning by focusing control of an electronic focus (EF) lens is implemented. The projection of a grating pattern is based on a digital micromirror device, which means fast phase-shifting with high precision. A field programmable gate array-based master control center board acts as the coordinator of the MMP system; it harmonizes the workflows, such as grating projection, focusing control of the EF lens, and fringe pattern capture. Fourier transform, phase-shifting technique, and temporary Fourier transform are used for modulation analysis in different operation modes. The proposed system features focusing control, speed, programmability, compactness, and availability. This paper details the principle of MMP for multioperation modes and the design of the proposed system. The performances of different operation modes are analyzed and compared, and a work piece with steep holes is measured to verify this multimode MMP system.

A Reward-Based Behavioral Platform to Measure Neural Activity during Head-Fixed Behavior

PubMed Central

Micallef, Andrew H.; Takahashi, Naoya; Larkum, Matthew E.; Palmer, Lucy M.

2017-01-01

Understanding the neural computations that contribute to behavior requires recording from neurons while an animal is behaving. This is not an easy task as most subcellular recording techniques require absolute head stability. The Go/No-Go sensory task is a powerful decision-driven task that enables an animal to report a binary decision during head-fixation. Here we discuss how to set up an Ardunio and Python based platform system to control a Go/No-Go sensory behavior paradigm. Using an Arduino micro-controller and Python-based custom written program, a reward can be delivered to the animal depending on the decision reported. We discuss the various components required to build the behavioral apparatus that can control and report such a sensory stimulus paradigm. This system enables the end user to control the behavioral testing in real-time and therefore it provides a strong custom-made platform for probing the neural basis of behavior. PMID:28620282

Emotional and cognitive influences in air traffic controller tasks: An investigation using a virtual environment?

PubMed

Truschzinski, Martina; Betella, Alberto; Brunnett, Guido; Verschure, Paul F M J

2018-05-01

Air traffic controllers are required to perform complex tasks which require attention and high precision. This study investigates how the difficulty of such tasks influences emotional states, cognitive workload and task performance. We use quantitative and qualitative measurements, including the recording of pupil dilation and changes in affect using questionnaires. Participants were required to perform a number of air traffic control tasks using the immersive human accessible Virtual Reality space in the "eXperience Induction Machine". Based on the data collected, we developed and validated a model which integrates personality, workload and affective theories. Our results indicate that the difficulty of an air traffic control task has a direct influence on cognitive workload as well as on the self-reported mood; whereas both mood and workload seem to change independently. In addition, we show that personality, in particular neuroticism, affects both mood and performance of the participants. Copyright © 2018 Elsevier Ltd. All rights reserved.

Requirements for a mobile communications satellite system. Volume 3: Large space structures measurements study

NASA Technical Reports Server (NTRS)

Akle, W.

1983-01-01

This study report defines a set of tests and measurements required to characterize the performance of a Large Space System (LSS), and to scale this data to other LSS satellites. Requirements from the Mobile Communication Satellite (MSAT) configurations derived in the parent study were used. MSAT utilizes a large, mesh deployable antenna, and encompasses a significant range of LSS technology issues in the areas of structural/dynamics, control, and performance predictability. In this study, performance requirements were developed for the antenna. Special emphasis was placed on antenna surface accuracy, and pointing stability. Instrumentation and measurement systems, applicable to LSS, were selected from existing or on-going technology developments. Laser ranging and angulation systems, presently in breadboard status, form the backbone of the measurements. Following this, a set of ground, STS, and GEO-operational were investigated. A third scale (15 meter) antenna system as selected for ground characterization followed by STS flight technology development. This selection ensures analytical scaling from ground-to-orbit, and size scaling. Other benefits are cost and ability to perform reasonable ground tests. Detail costing of the various tests and measurement systems were derived and are included in the report.

A "caliper" type of controlled-source, frequency-domain, electromagnetic sounding method

NASA Astrophysics Data System (ADS)

Zhang, W.; Lin, J.; Zhou, F.; Liu, C.; Chen, J.; Xue, K.; Liu, L.; Wu, Y.

2011-12-01

We developed a special measurement manner for controlled-source, frequency-domain, electromagnetic sounding method that can improve resolution and efficiency, called as "caliper". This manner is base on our array electromagnetic system DPS-I, which consists of 53 channels and can cover 2500 m survey line at one arrangement. There are several steps to apply this method. First, a rough measurement is carried out, using large dynamic range but sparse frequencies. The ratio of adjacent frequency is set to be 2 or 4. The frequency points cover the entire frequency band that is required according to the geological environment, and are almost equidistantly distributed at logarithmic axis. Receivers array are arranged in one or more survey lines to measure the amplitude and phase of electromagnetic field components simultaneously. After all frequency points for rough measurement are measured, data in each sub-receiver are transmitted to the controller and the apparent resistivity and phase are calculated in field quickly. Then the pseudo section diagrams of apparent resistivity and phase are drew. By the pseudo section we can roughly lock the abnormal zone and determine the frequency band required for detail investigation of abnormal zone. Next, the measurement using high density of frequencies in this frequency band is carried out, which we called "detailed measurement". The ratio of adjacent frequency in this time is m which lies between 1 and 2. The exact value of m will depend on how detailed that the user expected. After "detailed measurement" is finished, the pseudo section diagrams of apparent resistivity and phase are drew in the same way with the first step. We can see more detailed information about the abnormal zone and decide whether further measurement is necessary. If it is necessary, we can repeat the second step using smaller m until the resolution meet the requirements to distinguish the target. By simulation, we know that high density of frequencies really help us to improve resolution. But we also need to say that the improvement is limited and it will do no help to add frequencies if the frequency is already dense enough. This method not only improves efficiency, but also improves the ability to distinguish the abnormal body. This measurement mode consisting of rough measurement and detailed measurement is similar to the caliper measurement of length, so called "caliper" type. It is accurate and fast. It not only can be applied to frequency-domain sounding, such as controlled source audio -frequency magnetotelluric (CSAMT), but also can be extended to the spectral induced polarization method. By using this measurement manner, high resolution and high-efficiency can be expected.

An Anaylsis of Control Requirements and Control Parameters for Direct-Coupled Turbojet Engines

NASA Technical Reports Server (NTRS)

Novik, David; Otto, Edward W.

1947-01-01

Requirements of an automatic engine control, as affected by engine characteristics, have been analyzed for a direct-coupled turbojet engine. Control parameters for various conditions of engine operation are discussed. A hypothetical engine control is presented to illustrate the use of these parameters. An adjustable speed governor was found to offer a desirable method of over-all engine control. The selection of a minimum value of fuel flow was found to offer a means of preventing unstable burner operation during steady-state operation. Until satisfactory high-temperature-measuring devices are developed, air-fuel ratio is considered to be a satisfactory acceleration-control parameter for the attainment of the maximum acceleration rates consistent with safe turbine temperatures. No danger of unstable burner operation exists during acceleration if a temperature-limiting acceleration control is assumed to be effective. Deceleration was found to be accompanied by the possibility of burner blow-out even if a minimum fuel-flow control that prevents burner blow-out during steady-state operation is assumed to be effective. Burner blow-out during deceleration may be eliminated by varying the value of minimum fuel flow as a function of compressor-discharge pressure, but in no case should the fuel flow be allowed to fall below the value required for steady-state burner operation.

Multimode ergometer system

NASA Technical Reports Server (NTRS)

Bynum, B. G.; Gause, R. L.; Spier, R. A.

1971-01-01

System overcomes previous ergometer design and calibration problems including inaccurate measurements, large weight, size, and input power requirements, poor heat dissipation, high flammability, and inaccurate calibration. Device consists of lightweight, accurately controlled ergometer, restraint system, and calibration system.

40 CFR Table 5 to Subpart Eeee of... - Requirements for Performance Tests and Design Evaluations

Code of Federal Regulations, 2010 CFR

2010-07-01

... 1 through 10 a. A performance test to determine the organic HAP (or, upon approval, TOC) control... appendix A of 40 CFR part 63 for measuring form-aldehyde (A) Total organic HAP (or, upon approval, TOC), or... total organic HAP (or, upon approval, TOC) emissions are reduced by the required weight-percent or, as...

JPL noise control program

NASA Technical Reports Server (NTRS)

Klascius, A. F.

1975-01-01

Exposures of personnel to noise pollution at the Jet Propulsion Laboratories, Pasadena, California, were investigated. As a result of the study several protective measures were taken: (1) employees exposed to noise hazards were required to wear ear-protection devices, (2) mufflers and air diversion devices were installed around the wind tunnels; and (3) all personnel that are required to wear ear protection are given annual audimeter tests.

Exploring Improvement Science in Education: Promoting College Access in Fresno Unified School District

ERIC Educational Resources Information Center

Aguilar, Jorge; Nayfack, Michelle; Bush-Mecenas, Susan

2017-01-01

California's Local Control Funding Formula (LCFF) requires districts to report multiple measures of student performance that reflect success in the goal of preparing students for college, career, and citizenship. As they engage in the Local Control Accountability Plan (LCAP) process, they are expected to use state and local indicator data from…

Apparatus for controlling the scan width of a scanning laser beam

DOEpatents

Johnson, Gary W.

1996-01-01

Swept-wavelength lasers are often used in absorption spectroscopy applications. In experiments where high accuracy is required, it is desirable to continuously monitor and control the range of wavelengths scanned (the scan width). A system has been demonstrated whereby the scan width of a swept ring-dye laser, or semiconductor diode laser, can be measured and controlled in real-time with a resolution better than 0.1%. Scan linearity, or conformity to a nonlinear scan waveform, can be measured and controlled. The system of the invention consists of a Fabry-Perot interferometer, three CAMAC interface modules, and a microcomputer running a simple analysis and proportional-integral control algorithm. With additional modules, multiple lasers can be simultaneously controlled. The invention also includes an embodiment implemented on an ordinary PC with a multifunction plug-in board.

Apparatus for controlling the scan width of a scanning laser beam

DOEpatents

Johnson, G.W.

1996-10-22

Swept-wavelength lasers are often used in absorption spectroscopy applications. In experiments where high accuracy is required, it is desirable to continuously monitor and control the range of wavelengths scanned (the scan width). A system has been demonstrated whereby the scan width of a swept ring-dye laser, or semiconductor diode laser, can be measured and controlled in real-time with a resolution better than 0.1%. Scan linearity, or conformity to a nonlinear scan waveform, can be measured and controlled. The system of the invention consists of a Fabry-Perot interferometer, three CAMAC interface modules, and a microcomputer running a simple analysis and proportional-integral control algorithm. With additional modules, multiple lasers can be simultaneously controlled. The invention also includes an embodiment implemented on an ordinary PC with a multifunction plug-in board. 8 figs.

Advanced helicopter cockpit and control configurations for helicopter combat missions

NASA Technical Reports Server (NTRS)

Haworth, Loran A.; Atencio, Adolph, Jr.; Bivens, Courtland; Shively, Robert; Delgado, Daniel

1987-01-01

Two piloted simulations were conducted by the U.S. Army Aeroflightdynamics Directorate to evaluate workload and helicopter-handling qualities requirements for single pilot operation in a combat Nap-of-the-Earth environment. The single-pilot advanced cockpit engineering simulation (SPACES) investigations were performed on the NASA Ames Vertical Motion Simulator, using the Advanced Digital Optical Control System control laws and an advanced concepts glass cockpit. The first simulation (SPACES I) compared single pilot to dual crewmember operation for the same flight tasks to determine differences between dual and single ratings, and to discover which control laws enabled adequate single-pilot helicopter operation. The SPACES II simulation concentrated on single-pilot operations and use of control laws thought to be viable candidates for single pilot operations workload. Measures detected significant differences between single-pilot task segments. Control system configurations were task dependent, demonstrating a need for inflight reconfigurable control system to match the optimal control system with the required task.

ArControl: An Arduino-Based Comprehensive Behavioral Platform with Real-Time Performance.

PubMed

Chen, Xinfeng; Li, Haohong

2017-01-01

Studying animal behavior in the lab requires reliable delivering stimulations and monitoring responses. We constructed a comprehensive behavioral platform (ArControl: Arduino Control Platform) that was an affordable, easy-to-use, high-performance solution combined software and hardware components. The hardware component was consisted of an Arduino UNO board and a simple drive circuit. As for software, the ArControl provided a stand-alone and intuitive GUI (graphical user interface) application that did not require users to master scripts. The experiment data were automatically recorded with the built in DAQ (data acquisition) function. The ArControl also allowed the behavioral schedule to be entirely stored in and operated on the Arduino chip. This made the ArControl a genuine, real-time system with high temporal resolution (<1 ms). We tested the ArControl, based on strict performance measurements and two mice behavioral experiments. The results showed that the ArControl was an adaptive and reliable system suitable for behavioral research.

ArControl: An Arduino-Based Comprehensive Behavioral Platform with Real-Time Performance

PubMed Central

Chen, Xinfeng; Li, Haohong

2017-01-01

Studying animal behavior in the lab requires reliable delivering stimulations and monitoring responses. We constructed a comprehensive behavioral platform (ArControl: Arduino Control Platform) that was an affordable, easy-to-use, high-performance solution combined software and hardware components. The hardware component was consisted of an Arduino UNO board and a simple drive circuit. As for software, the ArControl provided a stand-alone and intuitive GUI (graphical user interface) application that did not require users to master scripts. The experiment data were automatically recorded with the built in DAQ (data acquisition) function. The ArControl also allowed the behavioral schedule to be entirely stored in and operated on the Arduino chip. This made the ArControl a genuine, real-time system with high temporal resolution (<1 ms). We tested the ArControl, based on strict performance measurements and two mice behavioral experiments. The results showed that the ArControl was an adaptive and reliable system suitable for behavioral research. PMID:29321735

Improved process robustness by using closed loop control in deep drawing applications

NASA Astrophysics Data System (ADS)

Barthau, M.; Liewald, M.; Christian, Held

2017-09-01

The production of irregular shaped deep-drawing parts with high quality requirements, which are common in today’s automotive production, permanently challenges production processes. High requirements on lightweight construction of passenger car bodies following European regulations until 2020 have been massively increasing the use of high strength steels substantially for years and are also leading to bigger challenges in sheet metal part production. Of course, the more and more complex shapes of today’s car body shells also intensify the issue due to modern and future design criteria. The metal forming technology tries to meet these challenges by developing a highly sophisticated layout of deep drawing dies that consider part quality requirements, process robustness and controlled material flow during the deep or stretch drawing process phase. A new method for controlling material flow using a closed loop system was developed at the IFU Stuttgart. In contrast to previous approaches, this new method allows a control intervention during the deep-drawing stroke. The blank holder force around the outline of the drawn part is used as control variable. The closed loop is designed as trajectory follow up with feed forward control. The used command variable is the part-wall stress that is measured with a piezo-electric measuring pin. In this paper the used control loop will be described in detail. The experimental tool that was built for testing the new control approach is explained here with its features. A method for gaining the follow up trajectories from simulation will also be presented. Furthermore, experimental results considering the robustness of the deep drawing process and the gain in process performance with developed control loop will be shown. Finally, a new procedure for the industrial application of the new control method of deep drawing will be presented by using a new kind of active element to influence the local blank holder pressure onto part flange.

Turbine gas temperature measurement and control system

NASA Technical Reports Server (NTRS)

Webb, W. L.

1973-01-01

A fluidic Turbine Inlet Gas Temperature (TIGIT) Measurement and Control System was developed for use on a Pratt and Whitney Aircraft J58 engine. Based on engine operating requirements, criteria for high temperature materials selection, system design, and system performance were established. To minimize development and operational risk, the TIGT control system was designed to interface with an existing Exhaust Gas Temperature (EGT) Trim System and thereby modulate steady-state fuel flow to maintain a desired TIGT level. Extensive component and system testing was conducted including heated (2300F) vibration tests for the fluidic sensor and gas sampling probe, temperature and vibration tests on the system electronics, burner rig testing of the TIGT measurement system, and in excess of 100 hours of system testing on a J58 engine. (Modified author abstract)

Personal customizing exercise with a wearable measurement and control unit

PubMed Central

Wang, Zhihui; Kiryu, Tohru; Tamura, Naoki

2005-01-01

Background Recently, wearable technology has been used in various health-related fields to develop advanced monitoring solutions. However, the monitoring function alone cannot meet all the requirements of customizing machine-based exercise on an individual basis by relying on biosignal-based controls. We propose a new wearable unit design equipped with measurement and control functions to support the customization process. Methods The wearable unit can measure the heart rate and electromyogram signals during exercise performance and output workload control commands to the exercise machines. The workload is continuously tracked with exercise programs set according to personally customized workload patterns and estimation results from the measured biosignals by a fuzzy control method. Exercise programs are adapted by relying on a computer workstation, which communicates with the wearable unit via wireless connections. A prototype of the wearable unit was tested together with an Internet-based cycle ergometer system to demonstrate that it is possible to customize exercise on an individual basis. Results We tested the wearable unit in nine people to assess its suitability to control cycle ergometer exercise. The results confirmed that the unit could successfully control the ergometer workload and continuously support gradual changes in physical activities. Conclusion The design of wearable units equipped with measurement and control functions is an important step towards establishing a convenient and continuously supported wellness environment. PMID:15982425

Real-time reflectometry measurement validation in H-mode regimes for plasma position control.

PubMed

Santos, J; Guimarais, L; Manso, M

2010-10-01

It has been shown that in H-mode regimes, reflectometry electron density profiles and an estimate for the density at the separatrix can be jointly used to track the separatrix within the precision required for plasma position control on ITER. We present a method to automatically remove, from the position estimation procedure, measurements performed during collapse and recovery phases of edge localized modes (ELMs). Based on the rejection mechanism, the method also produces an estimate confidence value to be fed to the position feedback controller. Preliminary results show that the method improves the real-time experimental separatrix tracking capabilities and has the potential to eliminate the need for an external online source of ELM event signaling during control feedback operation.

Optimal Redundancy Management in Reconfigurable Control Systems Based on Normalized Nonspecificity

NASA Technical Reports Server (NTRS)

Wu, N.Eva; Klir, George J.

1998-01-01

In this paper the notion of normalized nonspecificity is introduced. The nonspecifity measures the uncertainty of the estimated parameters that reflect impairment in a controlled system. Based on this notion, a quantity called a reconfiguration coverage is calculated. It represents the likelihood of success of a control reconfiguration action. This coverage links the overall system reliability to the achievable and required control, as well as diagnostic performance. The coverage, when calculated on-line, is used for managing the redundancy in the system.

Neutron Imaging Control Report: FY 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gibson, D. J.

2016-11-30

During the 2016 fiscal year, work began on the supervision and control systems for the neutron source currently under construction in the B194 accelerator caves. This source relies on a deuteron beam colliding with a high-speed stream of deuterium gas to create neutrons, which poses significant technical challenges. To help overcome those challenges, an integrated, operator-focused control architecture is required to collect and assimilate disparate data from a variety of measurement points, as well as provide the means to remotely control the system hardware.

Management of geriatric incontinence in nursing homes.

PubMed Central

Schnelle, J F; Traughber, B; Morgan, D B; Embry, J E; Binion, A F; Coleman, A

1983-01-01

A behavioral management system designed to reduce urinary incontinence was evaluated in two nursing homes with a pretest-posttest control group design with repeated measures. The primary components of the system were prompting and contingent social approval/disapproval which required approximately 2.5 minutes per patient per hour to administer. The frequency of correct toileting for experimental subjects increased by approximately 45%. The experimental groups were significantly different from the control groups on both incontinence and correct toileting measures. The results are discussed in view of the management issues inherent in nursing home settings. PMID:6885672

Floating Gate sensor for in-vivo dosimetry in radiation therapies. Design and first characterization.

NASA Astrophysics Data System (ADS)

Faigon, A.; Martinez Vazquez, I.; Carbonetto, S.; García Inza, M.; G

2017-01-01

A floating gate dosimeter was designed and fabricated in a standard CMOS technology. The design guides and characterization are presented. The characterization included the controlled charging by tunneling of the floating gate, and its discharging under irradiation while measuring the transistor drain current whose change is the measure of the absorbed dose. The resolution of the obtained device is close to 1 cGy satisfying the requirements for most radiation therapies dosimetry. Pending statistical proofs, the dosimeter is a potential candidate for wide in-vivo control of radiotherapy treatments.

Application of extremum seeking for time-varying systems to resonance control of RF cavities

DOE PAGES

Scheinker, Alexander

2016-09-13

A recently developed form of extremum seeking for time-varying systems is implemented in hardware for the resonance control of radio-frequency cavities without phase measurements. Normal conducting RF cavity resonance control is performed via a slug tuner, while superconducting TESLA-type cavity resonance control is performed via piezo actuators. The controller maintains resonance by minimizing reflected power by utilizing model-independent adaptive feedback. Unlike standard phase-measurement-based resonance control, the presented approach is not sensitive to arbitrary phase shifts of the RF signals due to temperature-dependent cable length or phasemeasurement hardware changes. The phase independence of this method removes common slowly varying drifts andmore » required periodic recalibration of phase-based methods. A general overview of the adaptive controller is presented along with the proof of principle experimental results at room temperature. Lastly, this method allows us to both maintain a cavity at a desired resonance frequency and also to dynamically modify its resonance frequency to track the unknown time-varying frequency of an RF source, thereby maintaining maximal cavity field strength, based only on power-level measurements.« less

Reinforcement learning for partially observable dynamic processes: adaptive dynamic programming using measured output data.

PubMed

Lewis, F L; Vamvoudakis, Kyriakos G

2011-02-01

Approximate dynamic programming (ADP) is a class of reinforcement learning methods that have shown their importance in a variety of applications, including feedback control of dynamical systems. ADP generally requires full information about the system internal states, which is usually not available in practical situations. In this paper, we show how to implement ADP methods using only measured input/output data from the system. Linear dynamical systems with deterministic behavior are considered herein, which are systems of great interest in the control system community. In control system theory, these types of methods are referred to as output feedback (OPFB). The stochastic equivalent of the systems dealt with in this paper is a class of partially observable Markov decision processes. We develop both policy iteration and value iteration algorithms that converge to an optimal controller that requires only OPFB. It is shown that, similar to Q -learning, the new methods have the important advantage that knowledge of the system dynamics is not needed for the implementation of these learning algorithms or for the OPFB control. Only the order of the system, as well as an upper bound on its "observability index," must be known. The learned OPFB controller is in the form of a polynomial autoregressive moving-average controller that has equivalent performance with the optimal state variable feedback gain.

Effect of music on labor pain relief, anxiety level and postpartum analgesic requirement: a randomized controlled clinical trial.

PubMed

Simavli, Serap; Gumus, Ilknur; Kaygusuz, Ikbal; Yildirim, Melahat; Usluogullari, Betul; Kafali, Hasan

2014-01-01

The control of labor pain and the prevention of suffering are major concerns of clinicians and their patients. The aim of this study was to evaluate the effect of music on labor pain and anxiety, maternal hemodynamics, fetal-neonatal parameters and postpartum analgesic requirement in primiparous women. Overall, 156 primiparous women who expected vaginal delivery were recruited and randomly assigned to a music group (n = 77) or a control group (n = 79). Women in the music group listened to music during labor. Pain intensity and anxiety level were measured using a visual analogue scale (0-10 cm). The two groups were compared in terms of pain severity, anxiety level, maternal hemodynamics, fetal-neonatal parameters and postpartum analgesic requirement. Mothers in the music therapy group had a lower level of pain and anxiety compared with those in the control group at all stages of labor (p < 0.001). A significant difference was observed between the two groups in terms of maternal hemodynamics and fetal heart rate after intervention (p < 0.01). Postpartum analgesic requirement significantly decreased in the music therapy group (p < 0.01). Listening to music during labor has a positive impact on labor pain and anxiety, maternal-fetal parameters and analgesic requirement. © 2014 S. Karger AG, Basel.

40 CFR Table 18 to Subpart Uuu of... - Requirements for Performance Tests for Organic HAP Emissions From Catalytic Reforming Units

Code of Federal Regulations, 2010 CFR

2010-07-01

... part 60, appendix A), as applicable c. Measure TOC concentration (for percent reduction standard) Method 25 (40 part 60, appendix A) to measure nonmethane TOC concentration (in carbon equivalents) at inlet and outlet of the control device. If the nonmethane TOC outlet concentration is expected to be...

40 CFR 63.7927 - What are my inspection and monitoring requirements for closed vent systems and control devices?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CPMS) to measure and record the hourly average total regeneration stream mass flow during each carbon... during regeneration (except during the cooling cycle). (3) Use a CPMS to measure and record the hourly average temperature of the adsorption bed after regeneration (and within 15 minutes after completing any...

40 CFR 63.7927 - What are my inspection and monitoring requirements for closed vent systems and control devices?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CPMS) to measure and record the hourly average total regeneration stream mass flow during each carbon... during regeneration (except during the cooling cycle). (3) Use a CPMS to measure and record the hourly average temperature of the adsorption bed after regeneration (and within 15 minutes after completing any...

40 CFR 63.7927 - What are my inspection and monitoring requirements for closed vent systems and control devices?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CPMS) to measure and record the hourly average total regeneration stream mass flow during each carbon... during regeneration (except during the cooling cycle). (3) Use a CPMS to measure and record the hourly average temperature of the adsorption bed after regeneration (and within 15 minutes after completing any...

40 CFR 63.7927 - What are my inspection and monitoring requirements for closed vent systems and control devices?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CPMS) to measure and record the hourly average total regeneration stream mass flow during each carbon... during regeneration (except during the cooling cycle). (3) Use a CPMS to measure and record the hourly average temperature of the adsorption bed after regeneration (and within 15 minutes after completing any...

40 CFR 63.7927 - What are my inspection and monitoring requirements for closed vent systems and control devices?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CPMS) to measure and record the hourly average total regeneration stream mass flow during each carbon... during regeneration (except during the cooling cycle). (3) Use a CPMS to measure and record the hourly average temperature of the adsorption bed after regeneration (and within 15 minutes after completing any...

40 CFR 63.1512 - Performance test/compliance demonstration requirements and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operator must conduct a performance test to measure THC and D/F emissions at the outlet of the control.../decoating kiln. The owner or operator must conduct performance tests to measure emissions of THC, D/F, HCl... operating temperature of each afterburner every 15 minutes during the THC and D/F performance tests; (ii...

40 CFR 63.1512 - Performance test/compliance demonstration requirements and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operator must conduct a performance test to measure THC and D/F emissions at the outlet of the control.../decoating kiln. The owner or operator must conduct performance tests to measure emissions of THC, D/F, HCl... operating temperature of each afterburner every 15 minutes during the THC and D/F performance tests; (ii...

DataHawk 1 data from COALA Engineering Evaluation

DOE Data Explorer

de Boer, Gijs

2015-10-07

These are raw (uncorrected) measurements from the DataHawk 1 sensor package. This is a level 0 data product and only minimal quality control measures have been applied. It is likely that substantial further corrections will be required to use these in a physically meaningful way. Please contact the PI if interested in using the dataset.

Efficacy of chlorine dioxide mouthwash against halitosis

NASA Astrophysics Data System (ADS)

Bestari, M. D.; Sunarto, H.; Kemal, Y.

2017-08-01

To ascertain the effectiveness of using chlorine dioxide mouthwash in addressing halitosis. Forty people were divided equally into the test group (required to gargle with mouthwash containing chlorine dioxide) and the control group (required to gargle with aquadest). The volatile sulfur compound (VSC) and organoleptic scores were measured before gargling and 30 min, 2 h, 4 h, and 6 h after. The Wilcoxon test analysis showed a significant difference (p<0.05) in the mean value of VSC scores between the test group and the control group in four testing periods after gargling. Chlorine dioxide mouthwash is effective in addressing halitosis.

Far field and wavefront characterization of a high-power semiconductor laser for free space optical communications

NASA Technical Reports Server (NTRS)

Cornwell, Donald M., Jr.; Saif, Babak N.

1991-01-01

The spatial pointing angle and far field beamwidth of a high-power semiconductor laser are characterized as a function of CW power and also as a function of temperature. The time-averaged spatial pointing angle and spatial lobe width were measured under intensity-modulated conditions. The measured pointing deviations are determined to be well within the pointing requirements of the NASA Laser Communications Transceiver (LCT) program. A computer-controlled Mach-Zehnder phase-shifter interferometer is used to characterize the wavefront quality of the laser. The rms phase error over the entire pupil was measured as a function of CW output power. Time-averaged measurements of the wavefront quality are also made under intensity-modulated conditions. The measured rms phase errors are determined to be well within the wavefront quality requirements of the LCT program.

Aerobic Exercise As a Potential Way to Improve Self-Control after Ego-Depletion in Healthy Female College Students.

PubMed

Zou, Zhiling; Liu, Yang; Xie, Jing; Huang, Xiting

2016-01-01

To test whether aerobic exercise can help build self-control stamina in healthy female young adults. Stamina in this context is defined as the capability to endure ego depletion, which can be measured with a self-control task following another activity also requiring self-control. Forty-five healthy undergraduate women were randomized to either an experimental group or control group. Participants in the experimental group were required to run in their campus running field for 30 min for a period of 5 weeks. Individuals in the control group were required to do diary entries regarding self-control in their daily lives, also for a period of 5 weeks. Before and after the 5-week intervention, participants completed a pain threshold test, a color word Stroop task and the following Cold Pressor Task (CPT) (with and without a distraction component). There was significant decrease of pain tolerance in session 2 relative to session 1 in the control group, but no such decline was found in the experimental group (though the improvement of pain tolerance was not significant), possibly suggesting successful self-control against this kind of decline. Five weeks of aerobic exercise increased self-control after ego depletion in terms of pain tolerance. These findings suggest that aerobic exercise may serve as a potential effective intervention for enhancing self-control in a college female population.

What's Measured Is Not Necessarily What Matters: A Cautionary Story from Public Health

PubMed Central

Schwartz, Robert

2016-01-01

A systematic review of the introduction and use of outcome-based performance management systems for public health organizations found differences between their use as a management system (which requires rigorous definition and measurement to allow comparison across organizational units) versus for improvement (which may require more flexibility). What is included in performance measurement/management systems is influenced by ease of measurement, data quality, ability of organization to control outcomes, ability to measure success in terms of doing things (rather than preventing things) and what is already happening. To the extent that most providers wish to do a good job, the availability of good data to enable benchmarking and improvement is an important step forward. However, to the extent that the health of a population is dependent on multiple factors, many beyond the mandate of the health system, too extensive a reliance on performance measurement may risk unintended consequences of marginalizing critical activities. PMID:28032824

Development of an instantaneous local fuel-concentration measurement probe: an engine application

NASA Astrophysics Data System (ADS)

Guibert, P.; Boutar, Z.; Lemoyne, L.

2003-11-01

This work presents a new tool which can deliver instantaneous local measurements of fuel concentration in an engine cylinder with a high temporal resolution, particularly during compression strokes. Fuel concentration is represented by means of equivalence fuel-air ratio, i.e. the real engine mass ratio of fuel to air divided by the same ratio in ideal stoichiometry conditions. Controlling the mixture configuration for any strategy in a spark ignition engine and for auto-ignition combustion has a dominant effect on the subsequent processes of ignition, flame propagation and auto-ignition combustion progression, pollutant formation under lean or even stoichiometric operating conditions. It is extremely difficult, under a transient operation, to control the equivalence air/fuel ratio precisely at a required value and at the right time. This requires the development of a highly accurate equivalence air/fuel ratio control system and a tool to measure using crank angle (CA) resolution. Although non-intrusive laser techniques have considerable advantages, they are most of the time inappropriate due to their optical inaccessibility or the complex experimental set-up involved. Therefore, as a response to the demand for a relatively simple fuel-concentration measurement system a probe is presented that replaces a spark plug and allows the engine to run completely normally. The probe is based on hot-wire like apparatus, but involves catalytic oxidation at the wire surface. The development, characteristics and calibration of the probe are presented followed by applications to in-cylinder engine measurements.

ROBOCAL: Gamma-ray isotopic hardware/software interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurd, J.R.; Bonner, C.A.; Ostenak, C.A.

1989-01-01

ROBOCAL, presently being developed at the Los Alamos National Laboratory, is a full-scale prototypical robotic system for remotely performing calorimetric and gamma-ray isotopics measurements of nuclear materials. It features a fully automated vertical stacker-retriever for storing and retrieving packaged nuclear materials from a multi-drawer system, and a fully automated, uniquely integrated gantry robot for programmable selection and transfer of nuclear materials to calorimetric and gamma-ray isotopic measurement stations. Since ROBOCAL is to require almost no operator intervention, a mechanical control system is required in addition to a totally automated assay system. The assay system must be a completely integrated datamore » acquisition and isotopic analysis package fully capable of performing state-of-the-art homogeneous and heterogeneous analyses on many varied matrices. The TRIFID assay system being discussed at this conference by J. G. Fleissner of the Rocky Flats Plant has been adopted because of its many automated features. These include: MCA/ADC setup and acquisition; spectral storage and analysis utilizing an expert system formalism; report generation with internal measurement control printout; user friendly screens and menus. The mechanical control portion consists primarily of two detector platforms and a sample platform, each with independent movement. Some minor modifications and additions are needed with TRIFID to interface the assay and mechanical portions with the CimRoc 4000 software controlling the robot. 6 refs., 5 figs., 3 tabs.« less

What are Soil Fumigants?

EPA Pesticide Factsheets

These pesticides, when applied to soil, form a gas to control pests including nematodes, fungi, bacteria, insects, and weeds, that live in the soil and can disrupt plant growth and crop production. Required safety measures reduce exposure risks.

29 CFR 1910.22 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... performed. Measures for the control of toxic materials are considered to be outside the scope of this... maintained in a clean and, so far as possible, a dry condition. Where wet processes are used, drainage shall...

42 CFR 423.150 - Scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PROGRAM VOLUNTARY MEDICARE PRESCRIPTION DRUG BENEFIT Cost Control and Quality Improvement Requirements... utilization management programs, quality assurance measures and systems, and medication therapy management... organization (QIO) activities. (f) Compliance deemed on the basis of accreditation. (g) Accreditation...

Designing Effective In-vehicle Icons

DOT National Transportation Integrated Search

1975-04-01

The design of a system for scanning sequences of aerial photographs with a computer-controlled flying-spot scanner and automatically measuring vehicle locations is described. Hardware and software requirements for an operational system of this type a...

Translations on Eastern Europe, Political, Sociological and Military Affairs, Number 1579

DTIC Science & Technology

1978-08-23

ized not by any random authority but specifically by state, economic, and public organs and organizations, under the guidance and control of the...development. The in- clusion of civil defense measures into the integrated plans insures the pos- sibility to control and implement their fulfillment...to superiors at all levels. Using means of political influence and party control they are able to energize the study and application of the require

Computation of output feedback gains for linear stochastic systems using the Zangwill-Powell method

NASA Technical Reports Server (NTRS)

Kaufman, H.

1977-01-01

Because conventional optimal linear regulator theory results in a controller which requires the capability of measuring and/or estimating the entire state vector, it is of interest to consider procedures for computing controls which are restricted to be linear feedback functions of a lower dimensional output vector and which take into account the presence of measurement noise and process uncertainty. To this effect a stochastic linear model has been developed that accounts for process parameter and initial uncertainty, measurement noise, and a restricted number of measurable outputs. Optimization with respect to the corresponding output feedback gains was then performed for both finite and infinite time performance indices without gradient computation by using Zangwill's modification of a procedure originally proposed by Powell.

CALL FOR PAPERS: 13th International Conference on Force and Mass Measurement

NASA Astrophysics Data System (ADS)

1992-01-01

10 14 May 1993, Helsinki Fair Centre, Finland Scope of the Conference The Conference reports and reviews the state of the art and future trends in force and mass measurements in science and industry. Emphasis is on the applications of new methods, current problems in calibration and quality control, as well as on advancements in new sensor technologies and industrial application of force and mass measurements. Main Themes and Topics 1. The state of the art and development trends in force and mass measurements Development and stability of high level mass standards Mass comparators and force standard machine New research topics in mass and force 2. Calibration and quality control Calibration methods Estimation of uncertainties and classification of accuracies Relations between calibration, testing and quality control Requirements for quality control Verification of weighing instruments and their main devices 3. Application of force and mass measurements Automatic weighing Mass flow measurements Quality control in process industry Sensor technologies Practical applications Special applications in industry, trade, etc. Deadline for submission of abstracts: 30 June 1992. For further information please contact: Finnish Society of Automation, Asemapäällikönkatu 12C, SF-00520 HELSINKI, Finland Phone: Int. +3580 1461 644, Fax: Int. +3580 1461 650

Report on SNL RCBC control options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ponciroli, R.; Vilim, R. B.

The attractive performance of the S-CO 2 recompression cycle arises from the thermo-physical properties of carbon dioxide near the critical point. However, to ensure efficient operation of the cycle near the critical point, precise control of the heat removal rate by the Printed Circuit Heat Exchanger (PCHE) upstream of the main compressor is required. Accomplishing this task is not trivial because of the large variations in fluid properties with respect to temperature and pressure near the critical point. The use of a model-based approach for the design of a robust feedback regulator is being investigated to achieve acceptable control ofmore » heat removal rate at different operating conditions. A first step in this procedure is the development of a dynamic model of the heat exchanger. In this work, a one-dimensional (1-D) control-oriented model of the PCHE was developed using the General Plant Analyzer and System Simulator (GPASS) code. GPASS is a transient simulation code that supports analysis and control of power conversion cycles based on the S-CO 2 Brayton cycle. This modeling capability was used this fiscal year to analyze experiment data obtained from the heat exchanger in the SNL recompression Brayton cycle. The analysis suggested that the error in the water flowrate measurement was greater than required for achieving precise control of heat removal rate. Accordingly, a new water flowmeter was installed, significantly improving the quality of the measurement. Comparison of heat exchanger measurements in subsequent experiments with code simulations yielded good agreement establishing a reliable basis for the use of the GPASS PCHE model for future development of a model-based feedback controller.« less

PI controller design for indirect vector controlled induction motor: A decoupling approach.

PubMed

Jain, Jitendra Kr; Ghosh, Sandip; Maity, Somnath; Dworak, Pawel

2017-09-01

Decoupling of the stator currents is important for smoother torque response of indirect vector controlled induction motors. Typically, feedforward decoupling is used to take care of current coupling that requires exact knowledge of motor parameters, additional circuitry and signal processing. In this paper, a method is proposed to design the regulating proportional-integral gains that minimize coupling without any requirement of the additional decoupler. The variation of the coupling terms for change in load torque is considered as the performance measure. An iterative linear matrix inequality based H ∞ control design approach is used to obtain the controller gains. A comparison between the feedforward and the proposed decoupling schemes is presented through simulation and experimental results. The results show that the proposed scheme is simple yet effective even without additional block or burden on signal processing. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Crew Exploration Vehicle Launch Abort Controller Performance Analysis

NASA Technical Reports Server (NTRS)

Sparks, Dean W., Jr.; Raney, David L.

2007-01-01

This paper covers the simulation and evaluation of a controller design for the Crew Module (CM) Launch Abort System (LAS), to measure its ability to meet the abort performance requirements. The controller used in this study is a hybrid design, including features developed by the Government and the Contractor. Testing is done using two separate 6-degree-of-freedom (DOF) computer simulation implementations of the LAS/CM throughout the ascent trajectory: 1) executing a series of abort simulations along a nominal trajectory for the nominal LAS/CM system; and 2) using a series of Monte Carlo runs with perturbed initial flight conditions and perturbed system parameters. The performance of the controller is evaluated against a set of criteria, which is based upon the current functional requirements of the LAS. Preliminary analysis indicates that the performance of the present controller meets (with the exception of a few cases) the evaluation criteria mentioned above.

Analysis of a Linear System for Variable-Thrust Control in the Terminal Phase of Rendezvous

NASA Technical Reports Server (NTRS)

Hord, Richard A.; Durling, Barbara J.

1961-01-01

A linear system for applying thrust to a ferry vehicle in the 3 terminal phase of rendezvous with a satellite is analyzed. This system requires that the ferry thrust vector per unit mass be variable and equal to a suitable linear combination of the measured position and velocity vectors of the ferry relative to the satellite. The variations of the ferry position, speed, acceleration, and mass ratio are examined for several combinations of the initial conditions and two basic control parameters analogous to the undamped natural frequency and the fraction of critical damping. Upon making a desirable selection of one control parameter and requiring minimum fuel expenditure for given terminal-phase initial conditions, a simplified analysis in one dimension practically fixes the choice of the remaining control parameter. The system can be implemented by an automatic controller or by a pilot.

Critical dosimetry measures and surrogate tools that can facilitate clinical success in PDT (Conference Presentation)

NASA Astrophysics Data System (ADS)

Pogue, Brian W.; Davis, Scott C.; Kanick, Stephen C.; Maytin, Edward V.; Pereira, Stephen P.; Palanisami, Akilan; Hasan, Tayyaba

2016-03-01

Photodynamic therapy can be a highly complex treatment with more than one parameter to control, or in some cases it is easily implemented with little control other than prescribed drug and light values. The role of measured dosimetry as related to clinical adoption has not been as successful as it could have been, and part of this may be from the conflicting goals of advocating for as many measurements as possible for accurate control, versus companies and clinical adopters advocating for as few measurements as possible, to keep it simple. An organized approach to dosimetry selection is required, which shifts from mechanistic measurements in pre-clinical and early phase I trials, towards just those essential dose limiting measurements and a focus on possible surrogate measures in phase II/III trials. This essential and surrogate approach to dosimetry should help successful adoption of clinical PDT if successful. The examples of essential dosimetry points and surrogate dosimetry tools which might be implemented in phase II and higher trials are discussed for solid tissue PDT with verteporfin and skin lesion treatment with aminolevulinc acid.

Active vibration control on a quarter-car for cancellation of road noise disturbance

NASA Astrophysics Data System (ADS)

Belgacem, Walid; Berry, Alain; Masson, Patrice

2012-07-01

In this paper, a methodology is presented for the cancellation of road noise, from the analysis of vibration transmission paths for an automotive suspension to the design of an active control system using inertial actuators on a suspension to reduce the vibrations transmitted to the chassis. First, experiments were conducted on a Chevrolet Epica LS automobile on a concrete test track to measure accelerations induced on the suspension by the road. These measurements were combined with experimental Frequency Response Functions (FRFs) measured on a quarter-car test bench to reconstruct an equivalent three dimensional force applied on the wheel hub. Second, FRFs measured on the test bench between the three-dimensional driving force and forces at each suspension/chassis linkage were used to characterize the different transmission paths of vibration energy to the chassis. Third, an experimental model of the suspension was constructed to simulate the configuration of the active control system, using the primary (disturbance) FRFs and secondary (control) FRFs also measured on the test bench. This model was used to optimize the configuration of the control actuators and to evaluate the required forces. Finally, a prototype of an active suspension was implemented and measurements were performed in order to assess the performance of the control approach. A 4.6 dB attenuation on transmitted forces was obtained in the 50-250 Hz range.

Function library programming to support B89 evaluation of Sheffield Apollo RS50 DCC (Direct Computer Control) CMM (Coordinate Measuring Machine)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frank, R.N.

1990-02-28

The Inspection Shop at Lawrence Livermore Lab recently purchased a Sheffield Apollo RS50 Direct Computer Control Coordinate Measuring Machine. The performance of the machine was specified to conform to B89 standard which relies heavily upon using the measuring machine in its intended manner to verify its accuracy (rather than parametric tests). Although it would be possible to use the interactive measurement system to perform these tasks, a more thorough and efficient job can be done by creating Function Library programs for certain tasks which integrate Hewlett-Packard Basic 5.0 language and calls to proprietary analysis and machine control routines. This combinationmore » provides efficient use of the measuring machine with a minimum of keyboard input plus an analysis of the data with respect to the B89 Standard rather than a CMM analysis which would require subsequent interpretation. This paper discusses some characteristics of the Sheffield machine control and analysis software and my use of H-P Basic language to create automated measurement programs to support the B89 performance evaluation of the CMM. 1 ref.« less

Vertical Position and Current Profile Measurements by Faraday-effect Polarimetry On EAST tokamak

NASA Astrophysics Data System (ADS)

Ding, Weixing; Liu, H. Q.; Jie, Y. X.; Brower, D. L.; Qian, J. P.; Zou, Z. Y.; Lian, H.; Wang, S. X.; Luo, Z. P.; Xiao, B. J.; Ucla Team; Asipp Team

2017-10-01

A primary goal for ITER and prospective fusion power reactors is to achieve controlled long-pulse/steady-state burning plasmas. For elongated divertor plasmas, both the vertical position and current profile have to be precisely controlled to optimize performance and prevent disruptions. An eleven-channel laser-based POlarimeter-INTerferometer (POINT) system has been developed for measuring the internal magnetic field in the EAST tokamak and can be used to obtain the plasma current profile and vertical position. Current profiles are determined from equilibrium reconstruction including internal magnetic field measurements as internal constraints. Horizontally-viewing chords at/near the mid-plane allow us to determine plasma vertical position non-inductively with subcentimeter spatial resolution and time response up to 1 s. The polarimeter-based position measurement, which does not require equilibrium reconstruction, is benchmarked against conventional flux loop measurements and can be exploited for feedback control. Work supported by US DOE through Grants No. DE-FG02-01ER54615 and No. DC-SC0010469.

Laboratory Methods for the Measurement of Pollutants in Water and Waste Effluents

NASA Technical Reports Server (NTRS)

Ballinger, Dwight G.

1971-01-01

The requirement for accurate, precise, and rapid analytical procedures for the examination of water and waste samples requires the use of a variety of instruments. The instrumentation in water laboratories includes atomic absorption, UV-visible. and infrared spectrophotometers, automatic colorimetric analyzers, gas chromatographs and mass spectrometers. Because of the emphasis on regulatory action, attention is being directed toward quality control of analytical results. Among the challenging problems are the differentiation of metallic species in water at nanogram concentrations, rapid measurement of free cyanide and free ammonia, more sensitive methods for arsenic and selenium and improved characterization of organic contaminants.

Arm Locking for the Laser Interferometer Space Antenna

NASA Technical Reports Server (NTRS)

Maghami, P. G.; Thorpe, J. I.; Livas, J.

2009-01-01

The Laser Interferometer Space Antenna (LISA) mission is a planned gravitational wave detector consisting of three spacecraft in heliocentric orbit. Laser interferometry is used to measure distance fluctuations between test masses aboard each spacecraft to the picometer level over a 5 million kilometer separation. Laser frequency fluctuations must be suppressed in order to meet the measurement requirements. Arm-locking, a technique that uses the constellation of spacecraft as a frequency reference, is a proposed method for stabilizing the laser frequency. We consider the problem of arm-locking using classical optimal control theory and find that our designs satisfy the LISA requirements.

Tailored Excitation for Multivariable Stability-Margin Measurement Applied to the X-31A Nonlinear Simulation

NASA Technical Reports Server (NTRS)

Bosworth, John T.; Burken, John J.

1997-01-01

Safety and productivity of the initial flight test phase of a new vehicle have been enhanced by developing the ability to measure the stability margins of the combined control system and vehicle in flight. One shortcoming of performing this analysis is the long duration of the excitation signal required to provide results over a wide frequency range. For flight regimes such as high angle of attack or hypersonic flight, the ability to maintain flight condition for this time duration is difficult. Significantly reducing the required duration of the excitation input is possible by tailoring the input to excite only the frequency range where the lowest stability margin is expected. For a multiple-input/multiple-output system, the inputs can be simultaneously applied to the control effectors by creating each excitation input with a unique set of frequency components. Chirp-Z transformation algorithms can be used to match the analysis of the results to the specific frequencies used in the excitation input. This report discusses the application of a tailored excitation input to a high-fidelity X-31A linear model and nonlinear simulation. Depending on the frequency range, the results indicate the potential to significantly reduce the time required for stability measurement.

The Earth Observing System AM Spacecraft - Thermal Control Subsystem

NASA Technical Reports Server (NTRS)

Chalmers, D.; Fredley, J.; Scott, C.

1993-01-01

Mission requirements for the EOS-AM Spacecraft intended to monitor global changes of the entire earth system are considered. The spacecraft is based on an instrument set containing the Advanced Spaceborne Thermal Emission and Reflection radiometer (ASTER), Clouds and Earth's Radiant Energy System (CERES), Multiangle Imaging Spectro-Radiometer (MISR), Moderate-Resolution Imaging Spectrometer (MODIS), and Measurements of Pollution in the Troposphere (MOPITT). Emphasis is placed on the design, analysis, development, and verification plans for the unique EOS-AM Thermal Control Subsystem (TCS) aimed at providing the required environments for all the onboard equipment in a densely packed layout. The TCS design maximizes the use of proven thermal design techniques and materials, in conjunction with a capillary pumped two-phase heat transport system for instrument thermal control.

Development of a Hand Held Thromboelastograph

DTIC Science & Technology

2015-01-01

documents will be referenced during the Entegrion PCM System design, verification and validation activities. EN 61010 -1:2010 (Edition3.0) Safety...requirements for electrical equipment for measurement, control, and laboratory use – Part 1: General requirements. EN 61010 -2-101:2002 Safety...IPC-A-610E Acceptability of Electronic Assemblies IPC 7711/21B Rework, Modification and Repair of Electronic Assemblies. IEC 62304:2006/AC:2008

Effects of carbohydrate counting method on metabolic control in children with type 1 diabetes mellitus.

PubMed

Gökşen, Damla; Atik Altınok, Yasemin; Ozen, Samim; Demir, Günay; Darcan, Sükran

2014-01-01

Medical nutritional therapy is important for glycemic control in children and adolescents with type 1 diabetes mellitus (T1DM). Carbohydrate (carb) counting, which is a more flexible nutritional method, has become popular in recent years. This study aimed to investigate the effects of carb counting on metabolic control, body measurements and serum lipid levels in children and adolescents with T1DM. T1DM patients aged 7-18 years and receiving flexible insulin therapy were divided into carb counting (n=52) and control (n=32) groups and were followed for 2 years in this randomized, controlled study. Demographic characteristics, body measurements, insulin requirements, hemoglobin A1c (HbA1c) and serum lipid levels at baseline and at follow-up were evaluated. There were no statistically significant differences between the groups in mean HbA1c values in the year preceding the study or in age, gender, duration of diabetes, puberty stage, total daily insulin dose, body mass index (BMI) standard deviation score (SDS) and serum lipid values. While there were no differences in BMI SDS, daily insulin requirement, total cholesterol, low-density lipoprotein and triglyceride values between the two groups (p>0.05) during the follow-up, annual mean HbA1c levels of the 2nd year were significantly lower in the carb counting group (p=0.010). The mean values of high-density lipoprotein were also significantly higher in the first and 2nd years in the carb counting group (p=0.02 and p=0.043, respectively). Carb counting may provide good metabolic control in children and adolescents with T1DM without causing any increase in weight or in insulin requirements.

Monitoring fugitive methane and natural gas emissions, validation of measurement techniques.

NASA Astrophysics Data System (ADS)

Robinson, Rod; Innocenti, Fabrizio; Gardiner, Tom; Helmore, Jon; Finlayson, Andrew; Connor, Andy

2017-04-01

The detection and quantification of fugitive and diffuse methane emissions has become an increasing priority in recent years. As the requirements for routine measurement to support industry initiatives increase there is a growing requirement to assess and validate the performance of fugitive emission measurement technologies. For reported emissions traceability and comparability of measurements is important. This talk will present recent work addressing these needs. Differential Absorption Lidar (DIAL) is a laser based remote sensing technology, able to map the concentration of gases in the atmosphere and determine emission fluxes for fugitive emissions. A description of the technique and its application for determining fugitive emissions of methane from oil and gas operations and waste management sites will be given. As DIAL has gained acceptance as a powerful tool for the measurement and quantification of fugitive emissions, and given the rich data it produces, it is being increasingly used to assess and validate other measurement approaches. In addition, to support the validation of technologies, we have developed a portable controlled release facility able to simulate the emissions from area sources. This has been used to assess and validate techniques which are used to monitor emissions. The development and capabilities of the controlled release facility will be described. This talk will report on recent studies using DIAL and the controlled release facility to validate fugitive emission measurement techniques. This includes side by side comparisons of two DIAL systems, the application of both the DIAL technique and the controlled release facility in a major study carried out in 2015 by South Coast Air Quality Management District (SCAQMD) in which a number of optical techniques were assessed and the development of a prototype method validation approach for techniques used to measure methane emissions from shale gas sites. In conclusion the talk will provide an update on the current status in the development of a European Standard for the measurement of fugitive emissions of VOCs and the use of validation data in the standardisation process and discuss the application of this to methane measurement.

Quality of mass-reared codling moth (Lepidoptera: Tortricidae) after long distance transportation 1. Logistics of shipping procedures and quality parameters as measured in the laboratory.

USDA-ARS?s Scientific Manuscript database

The sterile insect technique is a proven effective control tactic against lepidopteran pests when applied in an area-wide integrated pest management programme. The construction of insect mass-rearing facilities requires considerable investment and moth control strategies that include the use of ster...

A Comparison of Electromagnetic Induction Mapping to Measurements of Maximum Effluent Flow Depth for Assessing Flow Paths in Vegetative Treatment Areas

USDA-ARS?s Scientific Manuscript database

Vegetative treatment systems (VTSs) are one type of control structure that has shown potential to control runoff from open feedlots. To achieve maximum performance, sheet-flow over the width of the vegetative treatment area (VTA) is required. Tools, such as maps of flow paths through the VTA, are ne...

Kudzu: Where did it come from? And how can we stop it?

Treesearch

James H. Miller; Boyd Edwards

1983-01-01

Kudzu is spreading in the South and control measures are required on large acreages. Control can be accomplished by persistent applications of effective herbicides or by overgrazing for two to three years. Soil-active herbicides containing the active ingredient picloram or dicamba are presently most effective. Herbicide sprays should be applied in a mixture with 60 to...

Summary Report for the Evaluation of Current QA Processes Within the FRMAC FAL and EPA MERL.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shanks, Sonoya T.; Redding, Ted; Jaussi, Lynn

The Federal Radiological Monitoring and Assessment Center (FRMAC) relies on accurate and defensible analytical laboratory data to support its mission. Therefore, FRMAC must ensure that the environmental analytical laboratories providing analytical services maintain an ongoing capability to provide accurate analytical results to DOE. It is undeniable that the more Quality Assurance (QA) and Quality Control (QC) measures required of the laboratory, the less resources that are available for analysis of response samples. Being that QA and QC measures in general are understood to comprise a major effort related to a laboratory’s operations, requirements should only be considered if they aremore » deemed “value-added” for the FRMAC mission. This report provides observations of areas for improvement and potential interoperability opportunities in the areas of Batch Quality Control Requirements, Written Communications, Data Review Processes, Data Reporting Processes, along with the lessons learned as they apply to items in the early phase of a response that will be critical for developing a more efficient, integrated response for future interactions between the FRMAC and EPA assets.« less

Controlled sound field with a dual layer loudspeaker array

NASA Astrophysics Data System (ADS)

Shin, Mincheol; Fazi, Filippo M.; Nelson, Philip A.; Hirono, Fabio C.

2014-08-01

Controlled sound interference has been extensively investigated using a prototype dual layer loudspeaker array comprised of 16 loudspeakers. Results are presented for measures of array performance such as input signal power, directivity of sound radiation and accuracy of sound reproduction resulting from the application of conventional control methods such as minimization of error in mean squared pressure, maximization of energy difference and minimization of weighted pressure error and energy. Procedures for selecting the tuning parameters have also been introduced. With these conventional concepts aimed at the production of acoustically bright and dark zones, all the control methods used require a trade-off between radiation directivity and reproduction accuracy in the bright zone. An alternative solution is proposed which can achieve better performance based on the measures presented simultaneously by inserting a low priority zone named as the “gray” zone. This involves the weighted minimization of mean-squared errors in both bright and dark zones together with the gray zone in which the minimization error is given less importance. This results in the production of directional bright zone in which the accuracy of sound reproduction is maintained with less required input power. The results of simulations and experiments are shown to be in excellent agreement.

A High Stability Optical Shadow Sensor With Applications for Precision Accelerometers

NASA Astrophysics Data System (ADS)

Bramsiepe, Steven G.; Loomes, David; Middlemiss, Richard P.; Paul, Douglas J.; Hammond, Giles D.

2018-05-01

Gravimeters are devices which measure changes in the value of the gravitational acceleration, \\textit{g}. This information is used to infer changes in density under the ground allowing the detection of subsurface voids; mineral, oil and gas reserves; and even the detection of the precursors of volcanic eruptions. A micro-electro mechanical system (MEMS) gravimeter has been fabricated completely in silicon allowing the possibility of cost e-effective, lightweight and small gravimeters. To obtain a measurement of gravity, a highly stable displacement measurement of the MEMS is required. This requires the development of a portable electronics system that has a displacement sensitivity of $\\leq 2.5$ nm over a period of a day or more. The portable electronics system presented here has a displacement sensitivity $\\leq 10$ nm$/\\sqrt{\\textrm{Hz}}$ ($\\leq 0.6$ nm at $1000$ s). The battery power system used a modulated LED for measurements and required temperature control of the system to $\\pm$ 2 mK, monitoring of the tilt to $\\pm$ 2 $\\mu$radians, the storage of measured data and the transmission of the data to an external server.

Remote Monitoring of the Polarized Target's Control for E1039

NASA Astrophysics Data System (ADS)

Fox, David; SeaQuest Collaboration

2017-09-01

The 1039 experiment at FNAL will further our understanding of spin structure by measuring the contribution that sea quarks orbital angular momentum provide to overall nucleon spin. It is accepted that the valence-quarks of nucleons only provide 30% of the total nucleon spin. To study the nucleon's sea quark contribution, E1039 will use the Drell-Yan process by colliding 120 GeV un-polarized beam protons with polarized ammonia targets of hydrogen and deuterium. The asymmetric spin distributions of resulting dimuons will be measured. These asymmetries are sensitive, among other effects, to the orbital angular momentum contribution of the sea quarks. The polarized target requires a multi-stage vacuum pump located near the target. Since access to its present controls will not be possible during running, remote control and monitoring upgrades were required. A secondary control panel was purchased and tested. Information from the programmable logic controller (PLC) must be fed into our data stream to enable remote monitoring and to signal possible alarm conditions. This solution and the program created using explicit TCP/IP messaging to extract data tags from the PLC and log it within our databases will be presented. Supported by U.S. D.O.E. Medium Energy Nuclear Physics under Grant DE-FG02-03ER41243.

Designing on-Board Data Handling for EDF (Electric Ducted Fan) Rocket

NASA Astrophysics Data System (ADS)

Mulyana, A.; Faiz, L. A. A.

2018-02-01

The EDF (Electric Ducted Fan) rocket to launch requires a system of monitoring, tracking and controlling to allow the rocket to glide properly. One of the important components in the rocket is OBDH (On-Board Data Handling) which serves as a medium to perform commands and data processing. However, TTC (Telemetry, Tracking, and Command) are required to communicate between GCS (Ground Control Station) and OBDH on EDF rockets. So the design control system of EDF rockets and GCS for telemetry and telecommand needs to be made. In the design of integrated OBDH controller uses a lot of electronics modules, to know the behavior of rocket used IMU sensor (Inertial Measurement Unit) in which consist of 3-axis gyroscope sensor and Accelerometer 3-axis. To do tracking using GPS, compass sensor as a determinant of the direction of the rocket as well as a reference point on the z-axis of gyroscope sensor processing and used barometer sensors to measure the height of the rocket at the time of glide. The data can be known in real-time by sending data through radio modules at 2.4 GHz frequency using XBee-Pro S2B to GCS. By using windows filter, noises can be reduced, and it used to guarantee monitoring and controlling system can work properly.

Control Surface Interaction Effects of the Active Aeroelastic Wing Wind Tunnel Model

NASA Technical Reports Server (NTRS)

Heeg, Jennifer

2006-01-01

This paper presents results from testing the Active Aeroelastic Wing wind tunnel model in NASA Langley s Transonic Dynamics Tunnel. The wind tunnel test provided an opportunity to study aeroelastic system behavior under combined control surface deflections, testing for control surface interaction effects. Control surface interactions were observed in both static control surface actuation testing and dynamic control surface oscillation testing. The primary method of evaluating interactions was examination of the goodness of the linear superposition assumptions. Responses produced by independently actuating single control surfaces were combined and compared with those produced by simultaneously actuating and oscillating multiple control surfaces. Adjustments to the data were required to isolate the control surface influences. Using dynamic data, the task increases, as both the amplitude and phase have to be considered in the data corrections. The goodness of static linear superposition was examined and analysis of variance was used to evaluate significant factors influencing that goodness. The dynamic data showed interaction effects in both the aerodynamic measurements and the structural measurements.

FPGA-Based Smart Sensor for Online Displacement Measurements Using a Heterodyne Interferometer

PubMed Central

Vera-Salas, Luis Alberto; Moreno-Tapia, Sandra Veronica; Garcia-Perez, Arturo; de Jesus Romero-Troncoso, Rene; Osornio-Rios, Roque Alfredo; Serroukh, Ibrahim; Cabal-Yepez, Eduardo

2011-01-01

The measurement of small displacements on the nanometric scale demands metrological systems of high accuracy and precision. In this context, interferometer-based displacement measurements have become the main tools used for traceable dimensional metrology. The different industrial applications in which small displacement measurements are employed requires the use of online measurements, high speed processes, open architecture control systems, as well as good adaptability to specific process conditions. The main contribution of this work is the development of a smart sensor for large displacement measurement based on phase measurement which achieves high accuracy and resolution, designed to be used with a commercial heterodyne interferometer. The system is based on a low-cost Field Programmable Gate Array (FPGA) allowing the integration of several functions in a single portable device. This system is optimal for high speed applications where online measurement is needed and the reconfigurability feature allows the addition of different modules for error compensation, as might be required by a specific application. PMID:22164040

A Mobile System for Measuring Water Surface Velocities Using Unmanned Aerial Vehicle and Large-Scale Particle Image Velocimetry

NASA Astrophysics Data System (ADS)

Chen, Y. L.

2015-12-01

Measurement technologies for velocity of river flow are divided into intrusive and nonintrusive methods. Intrusive method requires infield operations. The measuring process of intrusive methods are time consuming, and likely to cause damages of operator and instrument. Nonintrusive methods require fewer operators and can reduce instrument damages from directly attaching to the flow. Nonintrusive measurements may use radar or image velocimetry to measure the velocities at the surface of water flow. The image velocimetry, such as large scale particle image velocimetry (LSPIV) accesses not only the point velocity but the flow velocities in an area simultaneously. Flow properties of an area hold the promise of providing spatially information of flow fields. This study attempts to construct a mobile system UAV-LSPIV by using an unmanned aerial vehicle (UAV) with LSPIV to measure flows in fields. The mobile system consists of a six-rotor UAV helicopter, a Sony nex5T camera, a gimbal, an image transfer device, a ground station and a remote control device. The activate gimbal helps maintain the camera lens orthogonal to the water surface and reduce the extent of images being distorted. The image transfer device can monitor the captured image instantly. The operator controls the UAV by remote control device through ground station and can achieve the flying data such as flying height and GPS coordinate of UAV. The mobile system was then applied to field experiments. The deviation of velocities measured by UAV-LSPIV of field experiments and handhold Acoustic Doppler Velocimeter (ADV) is under 8%. The results of the field experiments suggests that the application of UAV-LSPIV can be effectively applied to surface flow studies.

Improving NEC Fit

DTIC Science & Technology

2015-09-01

issues The Navy primarily uses Rating Control Number ( RCN ) Fit and NEC Fit to measure and assess enlisted fleet manning levels.1 In general, Fit...measures the quantity and quality of the crew relative to the unit’s authorized requirements. RCN Fit measures how well units are manned at the rating...below RCN Fit, and levels for non-critical NECs have been even lower. The levels in September 2014 indicate that a quarter of the critical NEC

Multifractal Properties of Process Control Variables

NASA Astrophysics Data System (ADS)

Domański, Paweł D.

2017-06-01

Control system is an inevitable element of any industrial installation. Its quality affects overall process performance significantly. The assessment, whether control system needs any improvement or not, requires relevant and constructive measures. There are various methods, like time domain based, Minimum Variance, Gaussian and non-Gaussian statistical factors, fractal and entropy indexes. Majority of approaches use time series of control variables. They are able to cover many phenomena. But process complexities and human interventions cause effects that are hardly visible for standard measures. It is shown that the signals originating from industrial installations have multifractal properties and such an analysis may extend standard approach to further observations. The work is based on industrial and simulation data. The analysis delivers additional insight into the properties of control system and the process. It helps to discover internal dependencies and human factors, which are hardly detectable.

Sliding mode-based lateral vehicle dynamics control using tyre force measurements

NASA Astrophysics Data System (ADS)

Kunnappillil Madhusudhanan, Anil; Corno, Matteo; Holweg, Edward

2015-11-01

In this work, a lateral vehicle dynamics control based on tyre force measurements is proposed. Most of the lateral vehicle dynamics control schemes are based on yaw rate whereas tyre forces are the most important variables in vehicle dynamics as tyres are the only contact points between the vehicle and road. In the proposed method, active front steering is employed to uniformly distribute the required lateral force among the front left and right tyres. The force distribution is quantified through the tyre utilisation coefficients. In order to address the nonlinearities and uncertainties of the vehicle model, a gain scheduling sliding-mode control technique is used. In addition to stabilising the lateral dynamics, the proposed controller is able to maintain maximum lateral acceleration. The proposed method is tested and validated on a multi-body vehicle simulator.

[Infection control team (ICT) in cooperation with microbiology laboratories].

PubMed

Okazaki, Mitsuhiro

2012-10-01

Infection control as a medical safety measure is an important issue in all medical facilities. In order to tackle this measure, cooperation between the infection control team (ICT) and microbiological laboratory is indispensable. Multiple drug-resistant bacteria have shifted from Gram-positive bacteria to Gram-negative bacilli within the last ten years. There are also a variety of bacilli, complicating the examination method and test results further. Therefore, cooperation between the ICT and microbiological laboratory has become important to understand examination results and to use them. In order to maintain functional cooperation, explanatory and communicative ability between the microbiological laboratory and ICT is required every day. Such positive information exchange will develop into efficient and functional ICT activity.

Pre-measured Products Boost Efficiency, Cut Costs

ERIC Educational Resources Information Center

Miller, Floyd G.; Pleasant, James

1974-01-01

Reduction of storage requirements, purchasing problems, handling, and costs has become a reality through the use of cleaning products in portion-controlled packages at the Chicago Circle Campus and the Medical Center of the University of Illinois. (Author)

Evaluation of the environmental impact of bridge deck runoff.

DOT National Transportation Integrated Search

2012-12-01

Bridges are located in very close proximity to receiving waters, and regulatory agencies often require specific stormwater : control measures for bridge deck runoff. While there is some information available on roadway runoff, few studies have : focu...

An efficient method for computing unsteady transonic aerodynamics of swept wings with control surfaces

NASA Technical Reports Server (NTRS)

Liu, D. D.; Kao, Y. F.; Fung, K. Y.

1989-01-01

A transonic equivalent strip (TES) method was further developed for unsteady flow computations of arbitrary wing planforms. The TES method consists of two consecutive correction steps to a given nonlinear code such as LTRAN2; namely, the chordwise mean flow correction and the spanwise phase correction. The computation procedure requires direct pressure input from other computed or measured data. Otherwise, it does not require airfoil shape or grid generation for given planforms. To validate the computed results, four swept wings of various aspect ratios, including those with control surfaces, are selected as computational examples. Overall trends in unsteady pressures are established with those obtained by XTRAN3S codes, Isogai's full potential code and measured data by NLR and RAE. In comparison with these methods, the TES has achieved considerable saving in computer time and reasonable accuracy which suggests immediate industrial applications.

Occupational noise exposure of nightclub bar employees in Ireland.

PubMed

Kelly, Aoife C; Boyd, Sara M; Henehan, Gary T M; Chambers, Gordon

2012-01-01

Due to the transposition of the EU Directive 2003/10/EC into Irish Law, the entertainment sector was obligated to comply with the requirements of the Safety, Health and Welfare at Work (General Application) Regulations 2007, Chapter 1 Part 5: Control of Noise at Work since February 2008. Compliance with the Noise Regulations was examined in 9 nightclubs in Ireland. The typical daily noise exposure of 19 bar employees was measured using 2 logging dosimeters and a Type 1 fixed position sound level meter. Physical site inspections identified nightclub noise control measures. Interviews and questionnaires were used to assess the managers and employees awareness of the noise legislation. The average bar employee daily noise exposure (L(EX, 8h)) was 92 dBA, almost 4 times more than the accepted legal limit. None of the venues examined were fully compliant with the requirements of the 2007 Noise Regulations, and awareness of this legislation was limited.

Cleaning Genesis Mission Payload for Flight with Ultra-Pure Water and Assembly in ISO Class 4 Environment

NASA Technical Reports Server (NTRS)

Allton, Judith H.

2012-01-01

Genesis mission to capture and return to Earth solar wind samples had very stringent contamination control requirements in order to distinguish the solar atoms from terrestrial ones. Genesis mission goals were to measure solar composition for most of the periodic table, so great care was taken to avoid particulate contamination. Since the number 1 and 2 science goals were to determine the oxygen and nitrogen isotopic composition, organic contamination was minimized by tightly controlling offgassing. The total amount of solar material captured in two years is about 400 micrograms spread across one sq m. The contamination limit requirement for each of C, N, and O was <1015 atoms/sq cm. For carbon, this is equivalent to 10 ng/cm2. Extreme vigilance was used in pre-paring Genesis collectors and cleaning hardware for flight. Surface contamination on polished silicon wafers, measured in Genesis laboratory is approximately 10 ng/sq cm.

A Detector for Cosmic Microwave Background Polarimetry

NASA Technical Reports Server (NTRS)

Wollack, E.; Cao, N.; Chuss, D.; Hsieh, W.-T.; Moseley, S. Harvey; Stevenson, T.; U-yen, K.

2008-01-01

We present preliminary design and development work on polarized detectors intended to enable Cosmic Microwave Background polarization measurements that will probe the first moments of the universe. The ultimate measurement will be challenging, requiring background-limited detectors and good control of systematic errors. Toward this end, we are integrating the beam control of HE-11 feedhorns with the sensitivity of transition-edge sensors. The coupling between these two devices is achieved via waveguide probe antennas and superconducting microstrip lines. This implementation allows band-pass filters to be incorporated on the detector chip. We believe that a large collection of single-mode polarized detectors will eventually be required for the reliable detection of the weak polarized signature that is expected to result from gravitational waves produced by cosmic inflation. This focal plane prototype is an important step along the path to this detection, resulting in a capability that will enable various future high performance instrument concepts.

Enabling optical metrology on small 5×5μm2 in-cell targets to support flexible sampling and higher order overlay and CD control for advanced logic devices nodes

NASA Astrophysics Data System (ADS)

Salerno, Antonio; de la Fuente, Isabel; Hsu, Zack; Tai, Alan; Chang, Hammer; McNamara, Elliott; Cramer, Hugo; Li, Daoping

2018-03-01

In next generation Logic devices, overlay control requirements shrink to sub 2.5nm level on-product overlay. Historically on-product overlay has been defined by the overlay capability of after-develop in-scribe targets. However, due to design and dimension, the after development metrology targets are not completely representative for the final overlay of the device. In addition, they are confined to the scribe-lane area, which limits the sampling possibilities. To address these two issues, metrology on structures matching the device structure and which can be sampled with high density across the device is required. Conventional after-etch CDSEM techniques on logic devices present difficulties in discerning the layers of interest, potential destructive charging effects and finally, they are limited by the long measurement times[1] [2] [3] . All together, limit the sampling densities and making CDSEM less attractive for control applications. Optical metrology can overcome most of these limitations. Such measurement, however, does require repetitive structures. This requirement is not fulfilled by logic devices, as the features vary in pitch and CD over the exposure field. The solution is to use small targets, with a maximum pad size of 5x5um2 , which can easily be placed in the logic cell area. These targets share the process and architecture of the device features of interest, but with a modified design that replicates as close as possible the device layout, allowing for in-device metrology for both CD and Overlay. This solution enables measuring closer to the actual product feature location and, not being limited to scribe-lanes, it opens the possibility of higher-density sampling schemes across the field. In summary, these targets become the facilitator of in-device metrology (IDM), that is, enabling the measurements both in-device Overlay and the CD parameters of interest and can deliver accurate, high-throughput, dense and after-etch measurements for Logic. Overlay improvements derived from a high-densely sampled Overlay map measured with 5x5 um2 In Device Metrology (IDM) targets were investigated on a customer Logic application. In this work we present both the main design aspects of the 5x5 um2 IDM targets, as well as the results on the improved Overlay performance.

Neural Basis of Stimulus-Angle-Dependent Motor Control of Wind-Elicited Walking Behavior in the Cricket Gryllus bimaculatus

PubMed Central

Oe, Momoko; Ogawa, Hiroto

2013-01-01

Crickets exhibit oriented walking behavior in response to air-current stimuli. Because crickets move in the opposite direction from the stimulus source, this behavior is considered to represent ‘escape behavior’ from an approaching predator. However, details of the stimulus-angle-dependent control of locomotion during the immediate phase, and the neural basis underlying the directional motor control of this behavior remain unclear. In this study, we used a spherical-treadmill system to measure locomotory parameters including trajectory, turn angle and velocity during the immediate phase of responses to air-puff stimuli applied from various angles. Both walking direction and turn angle were correlated with stimulus angle, but their relationships followed different rules. A shorter stimulus also induced directionally-controlled walking, but reduced the yaw rotation in stimulus-angle-dependent turning. These results suggest that neural control of the turn angle requires different sensory information than that required for oriented walking. Hemi-severance of the ventral nerve cords containing descending axons from the cephalic to the prothoracic ganglion abolished stimulus-angle-dependent control, indicating that this control required descending signals from the brain. Furthermore, we selectively ablated identified ascending giant interneurons (GIs) in vivo to examine their functional roles in wind-elicited walking. Ablation of GI8-1 diminished control of the turn angle and decreased walking distance in the initial response. Meanwhile, GI9-1b ablation had no discernible effect on stimulus-angle-dependent control or walking distance, but delayed the reaction time. These results suggest that the ascending signals conveyed by GI8-1 are required for turn-angle control and maintenance of walking behavior, and that GI9-1b is responsible for rapid initiation of walking. It is possible that individual types of GIs separately supply the sensory signals required to control wind-elicited walking. PMID:24244644

Evaluation of 12 blood glucose monitoring systems for self-testing: system accuracy and measurement reproducibility.

PubMed

Freckmann, Guido; Baumstark, Annette; Schmid, Christina; Pleus, Stefan; Link, Manuela; Haug, Cornelia

2014-02-01

Systems for self-monitoring of blood glucose (SMBG) have to provide accurate and reproducible blood glucose (BG) values in order to ensure adequate therapeutic decisions by people with diabetes. Twelve SMBG systems were compared in a standardized manner under controlled laboratory conditions: nine systems were available on the German market and were purchased from a local pharmacy, and three systems were obtained from the manufacturer (two systems were available on the U.S. market, and one system was not yet introduced to the German market). System accuracy was evaluated following DIN EN ISO (International Organization for Standardization) 15197:2003. In addition, measurement reproducibility was assessed following a modified TNO (Netherlands Organization for Applied Scientific Research) procedure. Comparison measurements were performed with either the glucose oxidase method (YSI 2300 STAT Plus™ glucose analyzer; YSI Life Sciences, Yellow Springs, OH) or the hexokinase method (cobas(®) c111; Roche Diagnostics GmbH, Mannheim, Germany) according to the manufacturer's measurement procedure. The 12 evaluated systems showed between 71.5% and 100% of the measurement results within the required system accuracy limits. Ten systems fulfilled with the evaluated test strip lot minimum accuracy requirements specified by DIN EN ISO 15197:2003. In addition, accuracy limits of the recently published revision ISO 15197:2013 were applied and showed between 54.5% and 100% of the systems' measurement results within the required accuracy limits. Regarding measurement reproducibility, each of the 12 tested systems met the applied performance criteria. In summary, 83% of the systems fulfilled with the evaluated test strip lot minimum system accuracy requirements of DIN EN ISO 15197:2003. Each of the tested systems showed acceptable measurement reproducibility. In order to ensure sufficient measurement quality of each distributed test strip lot, regular evaluations are required.

The validation by measurement theory of proposed object-oriented software metrics

NASA Technical Reports Server (NTRS)

Neal, Ralph D.

1994-01-01

Moving software development into the engineering arena requires controllability, and to control a process, it must be measurable. Measuring the process does no good if the product is not also measured, i.e., being the best at producing an inferior product does not define a quality process. Also, not every number extracted from software development is a valid measurement. A valid measurement only results when we are able to verify that the number is representative of the attribute that we wish to measure. Many proposed software metrics are used by practitioners without these metrics ever having been validated, leading to costly but often useless calculations. Several researchers have bemoaned the lack of scientific precision in much of the published software measurement work and have called for validation of software metrics by measurement theory. This dissertation applies measurement theory to validate fifty proposed object-oriented software metrics (Li and Henry, 1993; Chidamber and Kemerrer, 1994; Lorenz and Kidd, 1994).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheinker, Alexander

A recently developed form of extremum seeking for time-varying systems is implemented in hardware for the resonance control of radio-frequency cavities without phase measurements. Normal conducting RF cavity resonance control is performed via a slug tuner, while superconducting TESLA-type cavity resonance control is performed via piezo actuators. The controller maintains resonance by minimizing reflected power by utilizing model-independent adaptive feedback. Unlike standard phase-measurement-based resonance control, the presented approach is not sensitive to arbitrary phase shifts of the RF signals due to temperature-dependent cable length or phasemeasurement hardware changes. The phase independence of this method removes common slowly varying drifts andmore » required periodic recalibration of phase-based methods. A general overview of the adaptive controller is presented along with the proof of principle experimental results at room temperature. Lastly, this method allows us to both maintain a cavity at a desired resonance frequency and also to dynamically modify its resonance frequency to track the unknown time-varying frequency of an RF source, thereby maintaining maximal cavity field strength, based only on power-level measurements.« less

Flow Control and Measurement in Electric Propulsion Systems: Towards an AIAA Reference Standard

NASA Technical Reports Server (NTRS)

Snyder, John Steven; Baldwin, Jeff; Frieman, Jason D.; Walker, Mitchell L. R.; Hicks, Nathan S.; Polzin, Kurt A.; Singleton, James T.

2013-01-01

Accurate control and measurement of propellant flow to a thruster is one of the most basic and fundamental requirements for operation of electric propulsion systems, whether they be in the laboratory or on flight spacecraft. Hence, it is important for the electric propulsion community to have a common understanding of typical methods for flow control and measurement. This paper addresses the topic of propellant flow primarily for the gaseous propellant systems which have dominated laboratory research and flight application over the last few decades, although other types of systems are also briefly discussed. While most flight systems have employed a type of pressure-fed flow restrictor for flow control, both thermal-based and pressure-based mass flow controllers are routinely used in laboratories. Fundamentals and theory of operation of these types of controllers are presented, along with sources of uncertainty associated with their use. Methods of calibration and recommendations for calibration processes are presented. Finally, details of uncertainty calculations are presented for some common calibration methods and for the linear fits to calibration data that are commonly used.

Information systems as a tool to improve legal metrology activities

NASA Astrophysics Data System (ADS)

Rodrigues Filho, B. A.; Soratto, A. N. R.; Gonçalves, R. F.

2016-07-01

This study explores the importance of information systems applied to legal metrology as a tool to improve the control of measuring instruments used in trade. The information system implanted in Brazil has also helped to understand and appraise the control of the measurements due to the behavior of the errors and deviations of instruments used in trade, allowing the allocation of resources wisely, leading to a more effective planning and control on the legal metrology field. A study case analyzing the fuel sector is carried out in order to show the conformity of fuel dispersers according to maximum permissible errors. The statistics of measurement errors of 167,310 fuel dispensers of gasoline, ethanol and diesel used in the field were analyzed demonstrating the accordance of the fuel market in Brazil to the legal requirements.

Pointing and control system performance and improvement strategies for the SOFIA Airborne Telescope

NASA Astrophysics Data System (ADS)

Graf, Friederike; Reinacher, Andreas; Jakob, Holger; Lampater, Ulrich; Pfueller, Enrico; Wiedemann, Manuel; Wolf, Jürgen; Fasoulas, Stefanos

2016-07-01

The Stratospheric Observatory for Infrared Astronomy (SOFIA) has already successfully conducted over 300 flights. In its early science phase, SOFIA's pointing requirements and especially the image jitter requirements of less than 1 arcsec rms have driven the design of the control system. Since the first observation flights, the image jitter has been gradually reduced by various control mechanisms. During smooth flight conditions, the current pointing and control system allows us to achieve the standards set for early science on SOFIA. However, the increasing demands on the image size require an image jitter of less than 0.4 arcsec rms during light turbulence to reach SOFIA's scientific goals. The major portion of the remaining image motion is caused by deformation and excitation of the telescope structure in a wide range of frequencies due to aircraft motion and aerodynamic and aeroacoustic effects. Therefore the so-called Flexible Body Compensation system (FBC) is used, a set of fixed-gain filters to counteract the structural bending and deformation. Thorough testing of the current system under various flight conditions has revealed a variety of opportunities for further improvements. The currently applied filters have solely been developed based on a FEM analysis. By implementing the inflight measurements in a simulation and optimization, an improved fixed-gain compensation method was identified. This paper will discuss promising results from various jitter measurements recorded with sampling frequencies of up to 400 Hz using the fast imaging tracking camera.

Scalable Quantum Networks for Distributed Computing and Sensing

DTIC Science & Technology

2016-04-01

probabilistic measurement , so we developed quantum memories and guided-wave implementations of same, demonstrating controlled delay of a heralded single...Second, fundamental scalability requires a method to synchronize protocols based on quantum measurements , which are inherently probabilistic. To meet...AFRL-AFOSR-UK-TR-2016-0007 Scalable Quantum Networks for Distributed Computing and Sensing Ian Walmsley THE UNIVERSITY OF OXFORD Final Report 04/01