Self-Healing Phase Change Salogels with Tunable Gelation Temperature.

PubMed

Karimineghlani, Parvin; Palanisamy, Anbazhagan; Sukhishvili, Svetlana A

2018-05-02

Chemically cross-linked polymer matrices have demonstrated strong potential for shape stabilization of molten phase change materials (PCM). However, they are not designed to be fillable and removable from a heat exchange module for an easy replacement with new PCM matrices and lack self-healing capability. Here, a new category of shapeable, self-healing gels, "salogels", is introduced. The salogels reversibly disassemble in a high-salinity environment of a fluid inorganic PCM [lithium nitrate trihydrate (LNH)], at a preprogrammed temperature. LNH was employed as a high latent heat PCM and simultaneously as a solvent, which supported the formation of a network of polyvinyl alcohol (PVA) chains via physical cross-linking through poly(amidoamine) dendrimers of various generations. The existence of hydrogen bonding and the importance of low-hydration state of PVA for the efficient gelation were experimentally confirmed. The thermal behavior of PCM salogels was highly reversible and repeatable during multiple heating/cooling cycles. Importantly, the gel-sol transition temperature could be precisely controlled within a range of temperature above LNH's melting point by the choice of dendrimer generation and their concentration. Shape stabilization and self-healing properties of the salogels, taken together with tunability of their temperature-induced fluidization make these materials attractive for thermal energy storage applications that require on-demand removal and replacement of used inorganic PCM salt hydrates.

76 FR 16472 - Petition for Exemption From the Vehicle Theft Prevention Standard; Ford Motor Company

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-23

... a separate encrypted message to the body control module, the PEP/RFA module and the PCM. Ford... for the Volvo S60 for MYs 2006-2008 are 1.3803, 0.6907 and 2.3543 respectively. Using an average of 3...(a)(3): Promoting activation; preventing defeat or circumvention of the device by unauthorized...

Performance characteristics of a thermal energy storage module - A transient PCM/forced convection conjugate analysis

NASA Technical Reports Server (NTRS)

Cao, Y.; Faghri, A.

1991-01-01

The performance of a thermal energy storage module is simulated numerically. The change of phase of the phase-change material (PCM) and the transient forced convective heat transfer for the transfer fluid with low Prandtl numbers are solved simultaneously as a conjugate problem. A parametric study and a system optimization are conducted. The numerical results show that module geometry is crucial to the design of a space-based thermal energy storage system.

Pulse Code Modulation (PCM) data storage and analysis using a microcomputer

NASA Technical Reports Server (NTRS)

Massey, D. E.

1986-01-01

A PCM storage device/data analyzer is described. This instrument is a peripheral plug-in board especially built to enable a personal computer to store and analyze data from a PCM source. This board and custom written software turns a computer into a snapshot PCM decommutator. This instrument will take in and store many hundreds or thousands of PCM telemetry data frames, then sift through them over and over again. The data can be converted to any number base and displayed, examined for any bit dropouts or changes in particular words or frames, graphically plotted, or statistically analyzed. This device was designed and built for use on the NASA Sounding Rocket Program for PCM encoder configuration and testing.

Non-parametric PCM to ADM conversion. [Pulse Code to Adaptive Delta Modulation

NASA Technical Reports Server (NTRS)

Locicero, J. L.; Schilling, D. L.

1977-01-01

An all-digital technique to convert pulse code modulated (PCM) signals into adaptive delta modulation (ADM) format is presented. The converter developed is shown to be independent of the statistical parameters of the encoded signal and can be constructed with only standard digital hardware. The structure of the converter is simple enough to be fabricated on a large scale integrated circuit where the advantages of reliability and cost can be optimized. A concise evaluation of this PCM to ADM translation technique is presented and several converters are simulated on a digital computer. A family of performance curves is given which displays the signal-to-noise ratio for sinusoidal test signals subjected to the conversion process, as a function of input signal power for several ratios of ADM rate to Nyquist rate.

PARACOCCIDIOIDOMYCOSIS: CHALLENGES IN THE DEVELOPMENT OF A VACCINE AGAINST AN ENDEMIC MYCOSIS IN THE AMERICAS

PubMed Central

TABORDA, Carlos. P.; URÁN, M.E.; NOSANCHUK, J. D.; TRAVASSOS, L.R.

2015-01-01

SUMMARY Paracoccidioidomycosis (PCM), caused by Paracoccidioides spp, is an important endemic mycosis in Latin America. There are two recognized Paracoccidioides species, P. brasiliensis and P. lutzii, based on phylogenetic differences; however, the pathogenesis and disease manifestations of both are indistinguishable at present. Approximately 1,853 (~51,2%) of 3,583 confirmed deaths in Brazil due to systemic mycoses from 1996-2006 were caused by PCM. Antifungal treatment is required for patients with PCM. The initial treatment lasts from two to six months and sulfa derivatives, amphotericin B, azoles and terbinafine are used in clinical practice; however, despite prolonged therapy, relapses are still a problem. An effective Th1-biased cellular immune response is essential to control the disease, which can be induced by exogenous antigens or modulated by prophylactic or therapeutic vaccines. Stimulation of B cells or passive transference of monoclonal antibodies are also important means that may be used to improve the efficacy of paracoccidioidomycosis treatment in the future. This review critically details major challenges facing the development of a vaccine to combat PCM. PMID:26465365

Collaborative Software Development Approach Used to Deliver the New Shuttle Telemetry Ground Station

NASA Technical Reports Server (NTRS)

Kirby, Randy L.; Mann, David; Prenger, Stephen G.; Craig, Wayne; Greenwood, Andrew; Morsics, Jonathan; Fricker, Charles H.; Quach, Son; Lechese, Paul

2003-01-01

United Space Alliance (USA) developed and used a new software development method to meet technical, schedule, and budget challenges faced during the development and delivery of the new Shuttle Telemetry Ground Station at Kennedy Space Center. This method, called Collaborative Software Development, enabled KSC to effectively leverage industrial software and build additional capabilities to meet shuttle system and operational requirements. Application of this method resulted in reduced time to market, reduced development cost, improved product quality, and improved programmer competence while developing technologies of benefit to a small company in California (AP Labs Inc.). Many modifications were made to the baseline software product (VMEwindow), which improved its quality and functionality. In addition, six new software capabilities were developed, which are the subject of this article and add useful functionality to the VMEwindow environment. These new software programs are written in C or VXWorks and are used in conjunction with other ground station software packages, such as VMEwindow, Matlab, Dataviews, and PVWave. The Space Shuttle Telemetry Ground Station receives frequency-modulation (FM) and pulse-code-modulated (PCM) signals from the shuttle and support equipment. The hardware architecture (see figure) includes Sun workstations connected to multiple PCM- and FM-processing VersaModule Eurocard (VME) chassis. A reflective memory network transports raw data from PCM Processors (PCMPs) to the programmable digital-to-analog (D/A) converters, strip chart recorders, and analysis and controller workstations.

Experimental test of a hot water storage system including a macro-encapsulated phase change material (PCM)

NASA Astrophysics Data System (ADS)

Mongibello, L.; Atrigna, M.; Bianco, N.; Di Somma, M.; Graditi, G.; Risi, N.

2017-01-01

Thermal energy storage systems (TESs) are of fundamental importance for many energetic systems, essentially because they permit a certain degree of decoupling between the heat or cold production and the use of the heat or cold produced. In the last years, many works have analysed the addition of a PCM inside a hot water storage tank, as it can allow a reduction of the size of the storage tank due to the possibility of storing thermal energy as latent heat, and as a consequence its cost and encumbrance. The present work focuses on experimental tests realized by means of an indoor facility in order to analyse the dynamic behaviour of a hot water storage tank including PCM modules during a charging phase. A commercial bio-based PCM has been used for the purpose, with a melting temperature of 58°C. The experimental results relative to the hot water tank including the PCM modules are presented in terms of temporal evolution of the axial temperature profile, heat transfer and stored energy, and are compared with the ones obtained by using only water as energy storage material. Interesting insights, relative to the estimation of the percentage of melted PCM at the end of the experimental test, are presented and discussed.

Experimental Study of Thermal Energy Storage Characteristics using Heat Pipe with Nano-Enhanced Phase Change Materials

NASA Astrophysics Data System (ADS)

Krishna, Jogi; Kishore, P. S.; Brusly Solomon, A.

2017-08-01

The paper presents experimental investigations to evaluate thermal performance of heat pipe using Nano Enhanced Phase Change Material (NEPCM) as an energy storage material (ESM) for electronic cooling applications. Water, Tricosane and nano enhanced Tricosane are used as energy storage materials, operating at different heating powers (13W, 18W and 23W) and fan speeds (3.4V and 5V) in the PCM cooling module. Three different volume percentages (0.5%, 1% and 2%) of Nano particles (Al2O3) are mixed with Tricosane which is the primary PCM. This experiment is conducted to study the temperature distributions of evaporator, condenser and PCM during the heating as well as cooling. The cooling module with heat pipe and nano enhanced Tricosane as energy storage material found to save higher fan power consumption compared to the cooling module that utilities only a heat pipe.

Telemetry Standards, RCC Standard 106-17, Chapter 4, Pulse Code Modulation Standards

DTIC Science & Technology

2017-07-01

Frame Structure .............................................................................................. 4-6 4.3.3 Cyclic Redundancy Check (Class...Spectral and BEP Comparisons for NRZ and Bi-phase............................................ A-3 A.4. PCM Frame Structure Examples...4-4 Figure 4-3. PCM Frame Structure .......................................................................................... 4-6

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newmarker, Marc; Campbell, Mark

2012-03-16

Design, validate at prototype level, and then demonstrate a full size, 800 MWht Thermal Energy Storage (TES) system based on Phase Changing Material (PCM) TES modules with round trip efficiency in excess of 93%. The PCM TES module would be the building block of a TES system which can be deployed at costs inline with the DOE benchmark of 2020. The development of a reliable, unsophisticated, modular, and scalable TES system designed to be massmanufactured utilizing advanced automated fabrication and assembly processes and field installed in the most cost-effective configuration could facilitate the attainment of a Levelized Cost of Energymore » (LCOE) of $.07/kWh by 2015. It was believed that the DOE targets can be attained by finding the best combinationTES module size, its optimal integration in the power cycle, and readily available PCM. Work under this project ultimately focused on the development and performance evaluation of a 100kWht prototype heat exchanger. The design utilizes a commercially available heat exchanger product to create a unique latent heat PCM storage module. The novel ideal associated with this technology is the inclusion of an agitation mechanism that is activated during the discharge process to improve heat transfer. The prototype unit did not meet the performance goals estimated through modeling, nor did the estimated costs of the system fall in line with the goals established by DOE.« less

Nano-based PCMs for building energy efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik

Thermal storage using phase change materials (PCMs) is seen as a viable method for improving the energy efficiency of buildings. PCMs have been used in building applications in various forms PCM slurries in heat exchangers, macro- or microencapsulated PCMs in building envelopes, bulk PCM for modulating photovoltaic temperatures, etc. In the last decade a new class of PCMs, called nano-enhanced PCM (or nanoPCM), has been extensively investigated with the goal of improving the heat transfer and thermal storage properties of PCMs. NanoPCMs can primarily be categorized as nano-encapsulated PCMs and nanoparticle-PCM composites. The former are nano-sized capsules in which themore » PCM forms the core and is surrounded by a high-conductivity membrane or shell. The latter consist of PCM supported within nanostructures or nanoparticles dispersed in PCMs. This article reviews the current state of nanoPCM synthesis and characterization of their heat transfer and thermal storage properties. Further, a critical review of nanoPCM applications and their potential energy benefits is performed. Nano-enhanced PCMs exhibit higher thermal conductivities than regular PCM. However, whether the higher conductivity is desirable in all applications and if the property enhancements are worth the cost and effort needed to create nanoPCMs are questions that still need to be answered.« less

Pulse Code Modulation (PCM) encoder handbook for Aydin Vector MMP-900 series system

NASA Technical Reports Server (NTRS)

Raphael, David

1995-01-01

This handbook explicates the hardware and software properties of a time division multiplex system. This system is used to sample analog and digital data. The data is then merged with frame synchronization information to produce a serial pulse coded modulation (PCM) bit stream. Information in this handbook is required by users to design congruous interface and attest effective utilization of this encoder system. Aydin Vector provides all of the components for these systems to Goddard Space Flight Center/Wallops Flight Facility.

System Level Analysis of a Water PCM HX Integrated into Orion's Thermal Control System

NASA Technical Reports Server (NTRS)

Navarro, Moses; Hansen, Scott; Seth, Rubik; Ungar, Eugene

2015-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development an Orion system level analysis was performed using Thermal Desktop for a water PCM HX integrated into Orion's thermal control system in a 100km Lunar orbit. The study verified of the thermal model by using a wax PCM and analyzed 1) placing the PCM on the Internal Thermal Control System (ITCS) versus the External Thermal Control System (ETCS) 2) use of 30/70 PGW verses 50/50 PGW and 3) increasing the radiator area in order to reduce PCM freeze times. The analysis showed that for the assumed operating and boundary conditions utilizing a water PCM HX on Orion is not a viable option for any case. Additionally, it was found that the radiator area would have to be increased by at least 40% in order to support a viable water-based PCM HX.

Pulse Code Modulation (PCM) encoder handbook for Aydin Vector MMP-600 series system

NASA Technical Reports Server (NTRS)

Currier, S. F.; Powell, W. R.

1986-01-01

The hardware and software characteristics of a time division multiplex system are described. The system is used to sample analog and digital data. The data is merged with synchronization information to produce a serial pulse coded modulation (PCM) bit stream. Information presented herein is required by users to design compatible interfaces and assure effective utilization of this encoder system. GSFC/Wallops Flight Facility has flown approximately 50 of these systems through 1984 on sounding rockets with no inflight failures. Aydin Vector manufactures all of the components for these systems.

An experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management of electronic devices under pulsed power modes

NASA Astrophysics Data System (ADS)

Alshaer, W. G.; Rady, M. A.; Nada, S. A.; Palomo Del Barrio, Elena; Sommier, Alain

2017-02-01

The present article reports on a detailed experimental investigation of using carbon foam-PCM-MWCNTs composite materials for thermal management (TM) of electronic devices subjected to pulsed power. The TM module was fabricated by infiltrating paraffin wax (RT65) as a phase change material (PCM) and multi walled carbon nanotubes (MWCNTs) as a thermal conductivity enhancer in a carbon foam as a base structure. Two carbon foam materials of low and high values of thermal conductivities, CF20 and KL1-250 (3.1 and 40 W/m K), were tested as a base structure for the TM modules. Tests were conducted at different power intensities and power cycling/loading modes. Results showed that for all power varying modes and all carbon foams, the infiltration of RT65 into carbon foam reduces the temperature of TM module and results in damping the temperature spikes height. Infiltration of MWCNTS into RT65 further improves the effectiveness of TM module. Temperature damping was more pronounced in stand-alone pulsed power cycles as compared to pulsed power spikes modes. The effectiveness of inclusion of RT65 and RT65/MWCNTs in damping the temperature spikes height is remarkable in TM modules based on KL1-250 as compared to CF-20.

System Level Analysis of a Water PCM HX Integrated Into Orion's Thermal Control System Abstract

NASA Technical Reports Server (NTRS)

Navarro, Moses; Hansen, Scott; Ungar, Eugene; Sheth, Rubik

2015-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development an Orion system level analysis was performed using Thermal Desktop for a water PCM HX integrated into Orion's thermal control system and in a 100km Lunar orbit. The study analyzed 1) placing the PCM on the Internal Thermal Control System (ITCS) versus the External Thermal Control System (ETCS) 2) use of 30/70 PGW verses 50/50 PGW and 3) increasing the radiator area in order to reduce PCM freeze times. The analysis showed that for the assumed operating and boundary conditions utilizing a water PCM HX on Orion is not a viable option. Additionally, it was found that the radiator area would have to be increased over 20% in order to have a viable water-based PCM HX.

Multi-dimensional modeling of a thermal energy storage canister. M.S. Thesis - Cleveland State Univ., Dec. 1990

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.

1991-01-01

The Solar Dynamic Power Module being developed for Space Station Freedom uses a eutectic mixture of LiF-CaF2 phase change material (PCM) contained in toroidal canisters for thermal energy storage. Presented are the results from heat transfer analyses of a PCM containment canister. One and two dimensional finite difference computer models are developed to analyze heat transfer in the canister walls, PCM, void, and heat engine working fluid coolant. The modes of heat transfer considered include conduction in canister walls and solid PCM, conduction and pseudo-free convection in liquid PCM, conduction and radiation across PCM vapor filled void regions, and forced convection in the heat engine working fluid. Void shape, location, growth or shrinkage (due to density difference between the solid and liquid PCM phases) are prescribed based on engineering judgment. The PCM phase change process is analyzed using the enthalpy method. The discussion of the results focuses on how canister thermal performance is affected by free convection in the liquid PCM and void heat transfer. Characterizing these effects is important for interpreting the relationship between ground-based canister performance (in 1-g) and expected on-orbit performance (in micro-g). Void regions accentuate canister hot spots and temperature gradients due to their large thermal resistance. Free convection reduces the extent of PCM superheating and lowers canister temperatures during a portion of the PCM thermal charge period. Surprisingly small differences in canister thermal performance result from operation on the ground and operation on-orbit. This lack of a strong gravity dependency is attributed to the large contribution of container walls in overall canister energy redistribution by conduction.

Digital transmitter for data bus communications system

NASA Technical Reports Server (NTRS)

Proch, G. E. (Inventor)

1975-01-01

An improved digital transmitter for transmitting serial pulse code modulation (pcm) data at high bit rates over a transmission line is disclosed. When not transmitting, the transmitter features a high output impedance which prevents the transmitter from loading the transmission line. The pcm input is supplied to a logic control circuit which produces two discrete logic level signals which are supplied to an amplifier. The amplifier, which is transformer coupled to the output isolation circuitry, converts the discrete logic level signals to two high current level, ground isolated signals in the secondary windings of the coupling transformer. The latter signals are employed as inputs to the isolation circuitry which includes two series transistor pairs operating into a hybrid transformer functioning to isolate the transmitter circuitry from the transmission line.

Structural-functional integrated concrete with macro-encapsulated inorganic PCM

NASA Astrophysics Data System (ADS)

Mohseni, Ehsan; Tang, Waiching; Wang, Zhiyu

2017-09-01

Over the last few years the application of thermal energy storage system incorporating phase change materials (PCMs) to foster productivity and efficiency of buildings energy has grown rapidly. In this study, a structural-functional integrated concrete was developed using macro-encapsulated PCM-lightweight aggregate (LWA) as partial replacement (25 and 50% by volume) of coarse aggregate in control concrete. The PCM-LWA was prepared by incorporation of an inorganic PCM into porous LWAs through vacuum impregnation. The mechanical and thermal performance of PCM-LWA concrete were studied. The test results revealed that though the compressive strength of concrete with PCM-LWA was lower than the control concrete, but ranged from 22.02 MPa to 42.88 MPa which above the minimum strength requirement for structural application. The thermal performance test indicated that macro-encapsulated PCM-LWA has underwent the phase change transition reducing the indoor temperature.

Development, Testing, and Failure Mechanisms of a Replicative Ice Phase Change Material Heat Exchanger

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Hansen, Scott; Stephan, Ryan A.

2009-01-01

Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as Low Earth Orbit (LEO) and Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM s have over evaporators in this scenario is that they do not use a consumable. Wax PCM units have been baselined for the Orion thermal control system and also provide risk mitigation for the Altair Lander. However, the use of water as a PCM has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. An ice PCM heat exchanger that replicates the thermal energy storage capacity of an existing wax PCM unit was fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion are investigated. This paper presents the results to date of this investigation.

Development, Testing, and Failure Mechanisms of a Replicative Ice Phase Change Material Heat Exchanger

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Hansen, Scott; Stephan, Ryan A.

2010-01-01

Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as Low Earth Orbit (LEO) and Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM's have over evaporators in this scenario is that they do not use a consumable. Wax PCM units have been baselined for the Orion thermal control system and also provide risk mitigation for the Altair Lander. However, the use of water as a PCM has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. An ice PCM heat exchanger that replicates the thermal energy storage capacity of an existing wax PCM unit was fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion are investigated. This paper presents the results to date of this investigation. Nomenclature

Method and apparatus for a single channel digital communications system. [synchronization of received PCM signal by digital correlation with reference signal

NASA Technical Reports Server (NTRS)

Couvillon, L. A., Jr.; Carl, C.; Goldstein, R. M.; Posner, E. C.; Green, R. R. (Inventor)

1973-01-01

A method and apparatus are described for synchronizing a received PCM communications signal without requiring a separate synchronizing channel. The technique provides digital correlation of the received signal with a reference signal, first with its unmodulated subcarrier and then with a bit sync code modulated subcarrier, where the code sequence length is equal in duration to each data bit.

Centrioles regulate centrosome size by controlling the rate of Cnn incorporation into the PCM.

PubMed

Conduit, Paul T; Brunk, Kathrin; Dobbelaere, Jeroen; Dix, Carly I; Lucas, Eliana P; Raff, Jordan W

2010-12-21

centrosomes are major microtubule organizing centers in animal cells, and they comprise a pair of centrioles surrounded by an amorphous pericentriolar material (PCM). Centrosome size is tightly regulated during the cell cycle, and it has recently been shown that the two centrosomes in certain stem cells are often asymmetric in size. There is compelling evidence that centrioles influence centrosome size, but how centrosome size is set remains mysterious. we show that the conserved Drosophila PCM protein Cnn exhibits an unusual dynamic behavior, because Cnn molecules only incorporate into the PCM closest to the centrioles and then spread outward through the rest of the PCM. Cnn incorporation into the PCM is driven by an interaction with the conserved centriolar proteins Asl (Cep152 in humans) and DSpd-2 (Cep192 in humans). The rate of Cnn incorporation into the PCM is tightly regulated during the cell cycle, and this rate influences the amount of Cnn in the PCM, which in turn is an important determinant of overall centrosome size. Intriguingly, daughter centrioles in syncytial embryos only start to incorporate Cnn as they disengage from their mothers; this generates a centrosome size asymmetry, with mother centrioles always initially organizing more Cnn than their daughters. centrioles can control the amount of PCM they organize by regulating the rate of Cnn incorporation into the PCM. This mechanism can explain how centrosome size is regulated during the cell cycle and also allows mother and daughter centrioles to set centrosome size independently of one another.

Space thermal control development

NASA Technical Reports Server (NTRS)

Hoover, M. J.; Grodzka, P. G.; Oneill, M. J.

1971-01-01

The results of experimental investigations on a number of various phase change materials (PCMs) and PCMs in combination with metals and other materials are reported. The evaluations include the following PCM system performance characteristics: PCM and PCM/filler thermal diffusivities, the effects of long-term thermal cycling, PCM-container compatibility, and catalyst effectiveness and stability. Three PCMs demonstrated performance acceptable enough to be considered for use in prototype aluminum thermal control devices. These three PCMs are lithium nitrate trihydrate with zinc hydroxy nitrate catalyst, acetamide, and myristic acid. Of the fillers tested, aluminum honeycomb filler was found to offer the most increase in system thermal diffusivity.

Energy-Efficient Phase-Change Memory with Graphene as a Thermal Barrier.

PubMed

Ahn, Chiyui; Fong, Scott W; Kim, Yongsung; Lee, Seunghyun; Sood, Aditya; Neumann, Christopher M; Asheghi, Mehdi; Goodson, Kenneth E; Pop, Eric; Wong, H-S Philip

2015-10-14

Phase-change memory (PCM) is an important class of data storage, yet lowering the programming current of individual devices is known to be a significant challenge. Here we improve the energy-efficiency of PCM by placing a graphene layer at the interface between the phase-change material, Ge2Sb2Te5 (GST), and the bottom electrode (W) heater. Graphene-PCM (G-PCM) devices have ∼40% lower RESET current compared to control devices without the graphene. This is attributed to the graphene as an added interfacial thermal resistance which helps confine the generated heat inside the active PCM volume. The G-PCM achieves programming up to 10(5) cycles, and the graphene could further enhance the PCM endurance by limiting atomic migration or material segregation at the bottom electrode interface.

OA-7 Cargo Module Move from Airlock to Highbay

NASA Image and Video Library

2017-01-10

Inside an environmentally controlled shipping container the Orbital ATK OA-7 Cygnus spacecraft's pressurized cargo module (PCM) moves from an airlock to the high bay of the Space Station Processing Facility of NASA's Kennedy Space Center in Florida. Scheduled to launch on March 19, 2017, the Orbital ATK OA-7 mission will lift off atop a United Launch Alliance Atlas V rocket from Space launch Complex 41 at Cape Canaveral Air Force Station. The commercial resupply services mission to the International Space Station will deliver thousands of pounds of supplies, equipment and scientific research materials that improve life on Earth and drive progress toward future space exploration.

Avionics Architecture Standards as an Approach to Obsolescence Management

DTIC Science & Technology

2000-10-01

and goals is one method of system. The term System Architecture refers to a achieving the necessary critical mass of skilled and consistent set of such...Processing Module (GPM), Mass Memory Module executed on the modules within an ASAAC system will (MMM) and Power Conversion Module (PCM). be stored in a central...location, the Mass Memory * MOS -Module Support Layer to Operating System Module (MMM). Therefore, if modules are to be The purpose of the MOS

Experiments with phase change thermal energy storage canisters for Space Station Freedom

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.

1991-01-01

The solar dynamic power module proposed for the Space Station Freedom (SSF) uses the heat of fusion of a phase change material (PCM) to efficiently store thermal energy for use during eclipse periods. The PCM, a LiF-20CaF2 salt, is contained in annular, metal canisters located in a heat receiver at the focus of a solar concentrator. PCM canister ground-based experiments and analytical heat transfer studies are discussed. The hardware, test procedures, and test results from these experiments are discussed. After more than 900 simulated SSF orbital cycles, no canister cracks or leaks were observed and all data were successfully collected. The effect of 1-g test orientation on canister wall temperatures was generally small while void position was strongly dependent on test orientation and canister cooling. In one test orientation, alternating wall temperature data were measured that supports an earlier theory of oscillating vortex flow in the PCM melt. Analytical canister wall temperatures compared very favorably with experimental temperature data. This illustrates that ground-based canister thermal performance can be predicted well by analyses that employ straight-forward, engineering models of void behavior and liquid PCM free convection.

Phase change materials handbook

NASA Technical Reports Server (NTRS)

Hale, D. V.; Hoover, M. J.; Oneill, M. J.

1971-01-01

This handbook is intended to provide theory and data needed by the thermal design engineer to bridge the gap between research achievements and actual flight systems, within the limits of the current state of the art of phase change materials (PCM) technology. The relationship between PCM and more conventional thermal control techniques is described and numerous space and terrestrial applications of PCM are discussed. Material properties of the most promising PCMs are provided; the purposes and use of metallic filler materials in PCM composites are presented; and material compatibility considerations relevant to PCM design are included. The engineering considerations of PCM design are described, especially those pertaining to the thermodynamic and heat transfer phenomena peculiar to PCM design. Methods of obtaining data not currently available are presented. The special problems encountered in the space environment are described. Computational tools useful to the designer are discussed. In summary, each aspect of the PCM problem important to the design engineer is covered to the extent allowed by the scope of this effort and the state of the art.

Paracoccidioidomycosis in Brazilian Patients With and Without Human Immunodeficiency Virus Infection

PubMed Central

de Almeida, Fabrício Arantes; Neves, Fernando Freitas; Mora, Delio Jose; Reis, Tarcisio Albertin Dos; Sotini, Diego Moelas; Ribeiro, Barbara De Melo; Andrade-Silva, Leonardo Eurípedes; Nascentes, Gabriel Nogueira; Ferreira-Paim, Kennio; Silva-Vergara, Mario León

2017-01-01

Paracoccidioidomycosis (PCM) is endemic to Latin America, where 10 million people may be infected with Paracoccidioides brasiliensis/Paracoccidioides lutzii and 1,600,000 individuals live with human immunodeficiency virus (HIV) infection. An epidemiological overlapping of these infections occurred early in acquired immunodeficiency syndrome era with nearly 180 published cases. This study presents epidemiological, clinical, and outcome profiles for 31 PCM patients with HIV infection diagnosed in a teaching hospital in Brazil, and includes an update of previously reported cases. Medical records were reviewed and data compared with 64 PCM patients without HIV infection. Of the 31 PCM patients with HIV infection, 23 (74.1%) were male, with a median age of 36.7 years, whereas of the 64 PCM, 45 (70.3%) were male, with a median age of 35.1 years. Both groups presented similar proportions for smoking and alcoholism. PCM patients with HIV infection presented more fever, weight loss, and the acute clinical form than the PCM patients who had more mucosal and respiratory involvement characterizing the chronic form. Most PCM patients with HIV infection exhibited overlapping symptoms from both clinical forms with median symptom duration of 4.5 months compared with 8.3 months for the PCM control. Patients received sulfonamides and/or itraconazole for a median of 15.7 and 16.7 months for PCM/HIV-infected and PCM, respectively. Relapses occurred more in PCM (12 [30%]) than PCM/HIV-infected (4 [14.8%]) patients, whose mortality rate was higher (10 [32.8%]) than PCM patients (8 [20%]). The cases of PCM/HIV infection confirm that HIV can interact with some endemic diseases without increasing their frequency, while changing their natural history, clinical presentation, and outcome. The data presented here are in agreement with those observed in other studies. PMID:27895278

VHF command system study. [spectral analysis of GSFC VHF-PSK and VHF-FSK Command Systems

NASA Technical Reports Server (NTRS)

Gee, T. H.; Geist, J. M.

1973-01-01

Solutions are provided to specific problems arising in the GSFC VHF-PSK and VHF-FSK Command Systems in support of establishment and maintenance of Data Systems Standards. Signal structures which incorporate transmission on the uplink of a clock along with the PSK or FSK data are considered. Strategies are developed for allocating power between the clock and data, and spectral analyses are performed. Bit error probability and other probabilities pertinent to correct transmission of command messages are calculated. Biphase PCM/PM and PCM/FM are considered as candidate modulation techniques on the telemetry downlink, with application to command verification. Comparative performance of PCM/PM and PSK systems is given special attention, including implementation considerations. Gain in bit error performance due to coding is also considered.

Intersubunit distances in full-length, dimeric, bacterial phytochrome Agp1, as measured by pulsed electron-electron double resonance (PELDOR) between different spin label positions, remain unchanged upon photoconversion.

PubMed

Kacprzak, Sylwia; Njimona, Ibrahim; Renz, Anja; Feng, Juan; Reijerse, Edward; Lubitz, Wolfgang; Krauss, Norbert; Scheerer, Patrick; Nagano, Soshichiro; Lamparter, Tilman; Weber, Stefan

2017-05-05

Bacterial phytochromes are dimeric light-regulated histidine kinases that convert red light into signaling events. Light absorption by the N-terminal photosensory core module (PCM) causes the proteins to switch between two spectrally distinct forms, Pr and Pfr, thus resulting in a conformational change that modulates the C-terminal histidine kinase region. To provide further insights into structural details of photoactivation, we investigated the full-length Agp1 bacteriophytochrome from the soil bacterium Agrobacterium fabrum using a combined spectroscopic and modeling approach. We generated seven mutants suitable for spin labeling to enable application of pulsed EPR techniques. The distances between attached spin labels were measured using pulsed electron-electron double resonance spectroscopy to probe the arrangement of the subunits within the dimer. We found very good agreement of experimental and calculated distances for the histidine-kinase region when both subunits are in a parallel orientation. However, experimental distance distributions surprisingly showed only limited agreement with either parallel- or antiparallel-arranged dimer structures when spin labels were placed into the PCM region. This observation indicates that the arrangements of the PCM subunits in the full-length protein dimer in solution differ significantly from that in the PCM crystals. The pulsed electron-electron double resonance data presented here revealed either no or only minor changes of distance distributions upon Pr-to-Pfr photoconversion. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

Integrating Phase-Change Materials into Automotive Thermoelectric Generators

NASA Astrophysics Data System (ADS)

Klein Altstedde, Mirko; Rinderknecht, Frank; Friedrich, Horst

2014-06-01

Because the heat emitted by conventional combustion-engine vehicles during operation has highly transient properties, automotive thermoelectric generators (TEG) are intended for a particular operating state (design point). This, however, leads to two problems. First, whenever the combustion engine runs at low load, the maximum operating temperature cannot be properly utilised; second, a combustion engine at high load requires partial diversion of exhaust gas away from the TEG to protect the thermoelectric modules. An attractive means of stabilising dynamic exhaust behaviour (thereby keeping the TEG operating status at the design point for as long as possible) is use of latent heat storage, also known as phase-change materials (PCM). By positioning PCM between module and exhaust heat conduit, and choosing a material with a phase-change temperature matching the module's optimum operating temperature, it can be used as heat storage. This paper presents results obtained during examination of the effect of integration of latent heat storage on the potential of automotive TEG to convert exhaust heat. The research resulted in the development of a concept based on the initial integration idea, followed by proof of concept by use of a specially created prototype. In addition, the potential amount of energy obtained by use of a PCM-equipped TEG was calculated. The simulations indicated a significant increase in electrical energy was obtained in the selected test cycle.

Opposing effects of pericentrin and microcephalin on the pericentriolar material regulate CHK1 activation in the DNA damage response.

PubMed

Antonczak, A K; Mullee, L I; Wang, Y; Comartin, D; Inoue, T; Pelletier, L; Morrison, C G

2016-04-14

Genotoxic stresses lead to centrosome amplification, a frequently-observed feature in cancer that may contribute to genome instability and to tumour cell invasion. Here we have explored how the centrosome controls DNA damage responses. For most of the cell cycle, centrosomes consist of two centrioles embedded in the proteinaceous pericentriolar material (PCM). Recent data indicate that the PCM is not an amorphous assembly of proteins, but actually a highly organised scaffold around the centrioles. The large coiled-coil protein, pericentrin, participates in PCM assembly and has been implicated in the control of DNA damage responses (DDRs) through its interactions with checkpoint kinase 1 (CHK1) and microcephalin (MCPH1). CHK1 is required for DNA damage-induced centrosome amplification, whereas MCPH1 deficiency greatly increases the amplification seen after DNA damage. We found that the PCM showed a marked expansion in volume and a noticeable change in higher-order organisation after ionising radiation treatment. PCM expansion was dependent on CHK1 kinase activity and was potentiated by MCPH1 deficiency. Furthermore, pericentrin deficiency or mutation of a separase cleavage site blocked DNA damage-induced PCM expansion. The extent of nuclear CHK1 activation after DNA damage reflected the level of PCM expansion, with a reduction in pericentrin-deficient or separase cleavage site mutant-expressing cells, and an increase in MCPH1-deficient cells that was suppressed by the loss of pericentrin. Deletion of the nuclear export signal of CHK1 led to its hyperphosphorylation after irradiation and reduced centrosome amplification. Deletion of the nuclear localisation signal led to low CHK1 activation and low centrosome amplification. From these data, we propose a feedback loop from the PCM to the nuclear DDR in which CHK1 regulates pericentrin-dependent PCM expansion to control its own activation.

Experimental Investigation of Ice Phase Change Material Heat Exchangers

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Stephan, Ryan A.

2011-01-01

Phase change materials (PCM) may be useful for spacecraft thermal control systems that involve cyclical heat loads or cyclical thermal environments. Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. This can result in a decreased turndown ratio for the radiator and a reduced system mass. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents an overview of the results of this investigation from the past three years.

Experimental Investigation of Ice Phase Change Material Heat Exchangers

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Stephan, Ryan A.

2012-01-01

Phase change materials (PCM) may be useful for spacecraft thermal control systems that involve cyclical heat loads or cyclical thermal environments. Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. This can result in a decreased turndown ratio for the radiator and a reduced system mass. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents an overview of the results of this investigation from the past three years.

Calmodulin Gene Family in Potato: Developmental and Touch-Induced Expression of the mRNA Encoding a Novel Isoform

NASA Technical Reports Server (NTRS)

Takezawa, D.; Liu, Z. H.; An, G.; Poovaiah, B. W.

1995-01-01

Eight genomic clones of potato calmodulin (PCM1 to 8) were isolated and characterized. Sequence comparisons of different genes revealed that the deduced amino acid sequence of PCM1 had several unique substitutions, especially in the fourth Ca(2+)-binding area. The expression patterns of different genes were studied by northern analysis using the 3'-untranslated regions as probes. The expression of PCM1, 5, and 8 was highest in the stolon tip and it decreased during tuber development. The expression of PCM6 did not vary much in the tissues tested, except in the leaves, where the expression was lower; whereas, the expression of PCM4 was very low in all the tissues. The expression of PCM2 and PCM3 was not detected in any of the tissues tested. Among these genes, only PCM1 showed increased expression following touch stimulation. To study the regulation of PCM1, transgenic potato plants carrying the PCM1 promoter fused to the beta-glucuronidase (GUS) reporter gene were produced. GUS expression was found to be developmentally regulated and touch-responsive, indicating a positive correlation between the expression of PCM1 and GUS mRNAs. These results suggest that the 5'-flanking region of PCM1 controls developmental and touch-induced expression. X-Gluc staining patterns revealed that GUS localization is high in meristematic tissues such as the stem apex, stolon tip, and vascular regions.

OA-7 Cargo Module Arrival

NASA Image and Video Library

2017-01-09

Still sealed in its environmentally controlled shipping container, the Orbital ATK OA-7 Cygnus spacecraft's pressurized cargo module (PCM) has arrived inside the Space Station Processing Facility at NASA's Kennedy Space Center in Florida. Once the Cygnus spacecraft is removed from its shipping container, engineers and technicians will begin preparing for launch scheduled for March 2017. Orbital ATK CRS-7 will lift off atop a United Launch Alliance Atlas V rocket from Space launch Complex 41 at Cape Canaveral Air Force Station. The commercial resupply services mission to the International Space Station will deliver thousands of pounds of supplies, equipment and scientific research materials that improve life on Earth and drive progress toward future space exploration.

Testing and Failure Mechanisms of Ice Phase Change Material Heat Exchangers

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Stephan, Ryan A.; Hawkins-Reynolds, Ebony

2010-01-01

Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as Low Earth Orbit (LEO) and Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM s have over evaporators in this scenario is that they do not use a consumable. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents the results of testing that occurred from March through September of 2010 and builds on testing that occurred during the previous year.

Testing and Failure Mechanisms of Ice Phase Change Material Heat Exchangers

NASA Technical Reports Server (NTRS)

Leimkuehler, Thomas O.; Stephan, Ryan A.; Hawkins-Reynolds, Ebony

2011-01-01

Phase change materials (PCM) may be useful for thermal control systems that involve cyclical heat loads or cyclical thermal environments such as specific spacecraft orientations in Low Earth Orbit (LEO) and low beta angle Low Lunar Orbit (LLO). Thermal energy can be stored in the PCM during peak heat loads or in adverse thermal environments. The stored thermal energy can then be released later during minimum heat loads or in more favorable thermal environments. One advantage that PCM s have over evaporators in this scenario is that they do not use a consumable. The use of water as a PCM rather than the more traditional paraffin wax has the potential for significant mass reduction since the latent heat of formation of water is approximately 70% greater than that of wax. One of the potential drawbacks of using ice as a PCM is its potential to rupture its container as water expands upon freezing. In order to develop a space qualified ice PCM heat exchanger, failure mechanisms must first be understood. Therefore, a methodical experimental investigation has been undertaken to demonstrate and document specific failure mechanisms due to ice expansion in the PCM. A number of ice PCM heat exchangers were fabricated and tested. Additionally, methods for controlling void location in order to reduce the risk of damage due to ice expansion were investigated. This paper presents the results of testing that occurred from March through September of 2010 and builds on testing that occurred during the previous year.

Low-Cost Bio-Based Phase Change Materials as an Energy Storage Medium in Building Envelopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Abhari, Mr. Ramin; Shukla, Dr. Nitin

2015-01-01

A promising approach to increasing the energy efficiency of buildings is the implementation of phase change material (PCM) in building envelope systems. Several studies have reported the energy saving potential of PCM in building envelopes. However, wide application of PCMs in building applications has been inhibited, in part, by their high cost. This article describes a novel paraffin product made of naturally occurring fatty acids/glycerides trapped into high density polyethylene (HDPE) pellets and its performance in a building envelope application, with the ultimate goal of commercializing a low-cost PCM platform. The low-cost PCM pellets were mixed with cellulose insulation, installedmore » in external walls and field-tested under natural weatherization conditions for a period of several months. In addition, several PCM samples and PCM-cellulose samples were prepared under controlled conditions for laboratory-scale testing. The laboratory tests were performed to determine the phase change properties of PCM-enhanced cellulose insulation both at microscopic and macroscopic levels. This article presents the data and analysis from the exterior test wall and the laboratory-scale test data. PCM behavior is influenced by the weather and interior conditions, PCM phase change temperature and PCM distribution within the wall cavity, among other factors. Under optimal conditions, the field data showed up to 20% reduction in weekly heat transfer through an external wall due to the PCM compared to cellulose-only insulation.« less

Feasibility of using phase change materials to control the heat of hydration in massive concrete structures.

PubMed

Choi, Won-Chang; Khil, Bae-Soo; Chae, Young-Seok; Liang, Qi-Bo; Yun, Hyun-Do

2014-01-01

This paper presents experimental results that can be applied to select a possible phase change material (PCM), such as a latent heat material (LHM), to control the hydration heat in mass concrete structures. Five experimental tests (microconduction, simplified adiabatic temperature rise, heat, and compressive strength tests) were conducted to select the most desirable LHM out of seven types of inorganic PCM used in cement mortar and to determine the most suitable mix design. The results of these experimental tests were used to assess the feasibility of using PCM to reduce hydration heat in mass concrete that was examined. The experimental results show that cement mortar containing barium- [Ba(OH)2 · 8H2O] based PCM has the lowest amount of total hydration heat of the cement pastes. The barium-based PCM provides good latent heat properties that help to prevent volume change and microcracks caused by thermal stress in mass concrete.

Recruitment of PCM1 to the centrosome by the cooperative action of DISC1 and BBS4: a candidate for psychiatric illnesses.

PubMed

Kamiya, Atsushi; Tan, Perciliz L; Kubo, Ken-ichiro; Engelhard, Caitlin; Ishizuka, Koko; Kubo, Akiharu; Tsukita, Sachiko; Pulver, Ann E; Nakajima, Kazunori; Cascella, Nicola G; Katsanis, Nicholas; Sawa, Akira

2008-09-01

A role for the centrosome has been suggested in the pathology of major mental illnesses, especially schizophrenia (SZ). To show that pericentriolar material 1 protein (PCM1) forms a complex at the centrosome with disrupted-in-schizophrenia 1 (DISC1) and Bardet-Biedl syndrome 4 protein (BBS4), which provides a crucial pathway for cortical development associated with the pathology of SZ. To identify mutations in the PCM1 gene in an SZ population. Interaction of DISC1, PCM1, and BBS proteins was assessed by immunofluorescent staining and coimmunoprecipitation. Effects of PCM1, DISC1, and BBS on centrosomal functions and corticogenesis in vivo were tested by RNA interference. The PCM1 gene was examined by sequencing 39 exons and flanking splice sites. Probands and controls were from the collection of one of us (A.E.P.). Thirty-two probands with SZ from families that had excess allele sharing among affected individuals at 8p22 and 219 white controls. Protein interaction and recruitment at the centrosome in cells; neuronal migration in the cerebral cortex; and variant discovery in PCM1 in patients with SZ. PCM1 forms a complex with DISC1 and BBS4 through discrete binding domains in each protein. DISC1 and BBS4 are required for targeting PCM1 and other cargo proteins, such as ninein, to the centrosome in a synergistic manner. In the developing cerebral cortex, suppression of PCM1 leads to neuronal migration defects, which are phenocopied by the suppression of either DISC1 or BBS4 and are exacerbated by the concomitant suppression of both. Furthermore, a nonsense mutation that segregates with SZ spectrum psychosis was found in 1 family. Our data further support for the role of centrosomal proteins in cortical development and suggest that perturbation of centrosomal function contributes to the development of mental diseases, including SZ.

Hypothyroidism modifies morphometry and thyroid-hormone receptor expression in periurethral muscles of female rabbits.

PubMed

Sánchez-García, Octavio; Rodríguez-Castelán, Julia; Martínez-Gómez, Margarita; Cuevas, Estela; Castelán, Francisco

2016-11-01

To evaluate the morphometry and thyroid-hormone receptor (TR) expression in pelvic (pubococcygeus, Pcm) and perineal (bulbospongiosus, Bsm) muscles of control and hypothyroid female rabbits. Hypothyroidism was induced administering 0.02% methimazole in the drinking water for one month. Hematoxylin-eosin stained muscle sections were used to evaluate the fiber cross-sectional area (CSA) and the number of peripheral myonuclei per fiber. Immunohistochemistry was used to calculate the proportion of TR immunoreactive nuclei per fiber. Significant differences were considered at a P ≤ 0.05. As compared to control rabbits, hypothyroidism increased the averaged fiber CSA and the myonuclei per fiber in the Bsm. Although the myonuclei number per fiber was also increased in the Pcm, the effect concerning the fiber CSA was only observed in a fraction of the Pcm fibers. Both TRα and TRβ were similarly expressed in the Pcm and Bsm. Hypothyroidism increased the expression of the TRα in the Bsm. Meanwhile, the expression of TR isoforms in the Pcm was not altered. Our findings support that the TR signaling is directly involved in morphometrical changes induced by hypothyroidism in the Pcm and Bsm. The effect of hypothyroidism on the Pcm and Bsm could be related to the different type of fiber and metabolism that these muscles have. Neurourol. Urodynam. 35:895-901, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

Regulated Expression of a Calmodulin Isoform Alters Growth and Development in Potato

NASA Technical Reports Server (NTRS)

Poovaiah, B. W.; Takezawa, D.; An, G.; Han, T.-J.

1996-01-01

A transgene approach was taken to study the consequences of altered expression of a calmodutin iso-form on plant growth and development. Eight genomic clones of potato calmodulin (PCM 1 to 8) have been isolated and characterized. Among the potato calmodulin isoforms studied, PCM 1 differs from the other isoforms because of its unique amino acid substitutions. Transgenic potato plants were produced carrying sense construct of PCM 1 fused to the CAMV 35S promoter. Transgenic plants showing a moderate increase in PCM 1 MRNA exhibited strong apical dominance, produced elongated tubers, and were taller than the controls. Interestingly, the plants expressing the highest level of PCM 1 MRNA did not form underground tubers. Instead, these transgenic plants produced aerial tubers when allowed to grow for longer periods. The expression of different calmodulin isoforms (PCM 1, 5, 6, and 8) was studied in transgenic plants. Among the four potato calmodulin isoforms, only the expression of PCM 1 MRNA was altered in transgenic plants, while the expression of other isoforms was not significantly altered. Western analysis revealed increased PCM 1 protein in transgenic plants, indicating that the expression of both MRNA and protein are altered in transgenic plants. These results suggest that increasing the expression of PCM 1 alters growth and development in potato plants.

Digital Signal Processing Based Biotelemetry Receivers

NASA Technical Reports Server (NTRS)

Singh, Avtar; Hines, John; Somps, Chris

1997-01-01

This is an attempt to develop a biotelemetry receiver using digital signal processing technology and techniques. The receiver developed in this work is based on recovering signals that have been encoded using either Pulse Position Modulation (PPM) or Pulse Code Modulation (PCM) technique. A prototype has been developed using state-of-the-art digital signal processing technology. A Printed Circuit Board (PCB) is being developed based on the technique and technology described here. This board is intended to be used in the UCSF Fetal Monitoring system developed at NASA. The board is capable of handling a variety of PPM and PCM signals encoding signals such as ECG, temperature, and pressure. A signal processing program has also been developed to analyze the received ECG signal to determine heart rate. This system provides a base for using digital signal processing in biotelemetry receivers and other similar applications.

An alternative cooling system to enhance the safety of Li-ion battery packs

NASA Astrophysics Data System (ADS)

Kizilel, Riza; Sabbah, Rami; Selman, J. Robert; Al-Hallaj, Said

A passive thermal management system is evaluated for high-power Li-ion packs under stressful or abusive conditions, and compared with a purely air-cooling mode under normal and abuse conditions. A compact and properly designed passive thermal management system utilizing phase change material (PCM) provides faster heat dissipation than active cooling during high pulse power discharges while preserving sufficiently uniform cell temperature to ensure the desirable cycle life for the pack. This study investigates how passive cooling with PCM contributes to preventing the propagation of thermal runaway in a single cell or adjacent cells due to a cell catastrophic failure. Its effectiveness is compared with that of active cooling by forced air flow or natural convection using the same compact module and pack configuration corresponding to the PCM matrix technology. The effects of nickel tabs and spacing between the cells were also studied.

Aedes aegypti larvicide from the ethanolic extract of Piper nigrum black peppercorns.

PubMed

Santiago, Viviene S; Alvero, Rita Grace; Villaseñor, Irene M

2015-01-01

Due to unavailability of a vaccine and a specific cure to dengue, the focus nowadays is to develop an effective vector control method against the female Aedes aegypti mosquito. This study aims to determine the larvicidal fractions from Piper nigrum ethanolic extracts (PnPcmE) and to elucidate the identity of the bioactive compounds that comprise these larvicidal fractions. Larvicidal assay was performed by subjecting 3rd to 4th A. aegypti instar larvae to PnPcmE of P. nigrum. The PnPcmE exhibited potential larvicidal activity having an LC50 of 7.1246 ± 0.1304 ppm (mean ± Std error). Normal phase vacuum liquid chromatography of the PnPcmE was employed which resulted in five fractions, two of which showed larvicidal activity. The most active of the PnPcmE fractions is PnPcmE-1A, with an LC50 and LC90 of 1.7101 ± 0.0491 ppm and 3.7078 ppm, respectively. Subsequent purification of PnPcmE-1A allowed the identification of the larvicidal compound as oleic acid.

Air Force Geophysics Laboratory portable PCM ground station

NASA Astrophysics Data System (ADS)

Shaw, H.; Lawrence, F. A.

The present paper is concerned with the development of a portable Pulse-Code Modulation (PCM) telemetry station for the Air Force Geophysics Laboratory (AFGL). A system description is provided, taking into account the system equipment, the interface, the decommutator (DECOM) section of the interface, the direct memory access (DMA) section, and system specifications and capabilities. In the context of selecting between two conflicting philosophies regarding software, it was decided to favor a small scale specialized approach. Attention is given to the operating system, aspects of setting up the software, the application software, and questions of portability.

Regulated expression of a calmodulin isoform alters growth and development in potato.

PubMed

Poovaiah, B W; Takezawa, D; An, G; Han, T J

1996-01-01

A transgene approach was taken to study the consequences of altered expression of a calmodulin isoform on plant growth and development. Eight genomic clones of potato calmodulin (PCM1 to 8) have been isolated and characterized (Takezawa et al., 1995). Among the potato calmodulin isoforms studied, PCM1 differs from the other isoforms because of its unique amino acid substitutions. Transgenic potato plants were produced carrying sense construct of PCM1 fused to the CaMV 35S promoter. Transgenic plants showing a moderate increase in PCM1 mRNA exhibited strong apical dominance, produced elongated tubers, and were taller than the controls. Interestingly, the plants expressing the highest level of PCM1 mRNA did not form underground tubers. Instead, these transgenic plants produced aerial tubers when allowed to grow for longer periods. The expression of different calmodulin isoforms (PCM1, 5, 6, and 8) was studied in transgenic plants. Among the four potato calmodulin isoforms, only the expression of PCM1 mRNA was altered in transgenic plants, while the expression of other isoforms was not significantly altered. Western analysis revealed increased PCM1 protein in transgenic plants, indicating that the expression of both mRNA and protein are altered in transgenic plants. These results suggest that increasing the expression of PCM1 alters growth and development in potato plants.

Comparison of power curve monitoring methods

NASA Astrophysics Data System (ADS)

Cambron, Philippe; Masson, Christian; Tahan, Antoine; Torres, David; Pelletier, Francis

2017-11-01

Performance monitoring is an important aspect of operating wind farms. This can be done through the power curve monitoring (PCM) of wind turbines (WT). In the past years, important work has been conducted on PCM. Various methodologies have been proposed, each one with interesting results. However, it is difficult to compare these methods because they have been developed using their respective data sets. The objective of this actual work is to compare some of the proposed PCM methods using common data sets. The metric used to compare the PCM methods is the time needed to detect a change in the power curve. Two power curve models will be covered to establish the effect the model type has on the monitoring outcomes. Each model was tested with two control charts. Other methodologies and metrics proposed in the literature for power curve monitoring such as areas under the power curve and the use of statistical copulas have also been covered. Results demonstrate that model-based PCM methods are more reliable at the detecting a performance change than other methodologies and that the effectiveness of the control chart depends on the types of shift observed.

Development of a prototype thermoelectric space cooling system using phase change material to improve the performance

NASA Astrophysics Data System (ADS)

Zhao, Dongliang

The thermoelectric cooling system has advantages over conventional vapor compression cooling devices, including compact in size, light in weight, high reliability, no mechanical moving parts, no refrigerant, being powered by direct current, and easily switching between cooling and heating modes. However, it has been long suffering from its relatively high cost and low energy efficiency, which has restricted its usage to niche applications, such as space missions, portable cooling devices, scientific and medical equipment, where coefficient of performance (COP) is not as important as reliability, energy availability, and quiet operation environment. Enhancement of thermoelectric cooling system performance generally relies on two methods: improving thermoelectric material efficiency and through thermoelectric cooling system thermal design. This research has been focused on the latter one. A prototype thermoelectric cooling system integrated with phase change material (PCM) thermal energy storage unit for space cooling has been developed. The PCM thermal storage unit used for cold storage at night, functions as the thermoelectric cooling system's heat sink during daytime's cooling period and provides relatively lower hot side temperature for the thermoelectric cooling system. The experimental test of the prototype system in a reduced-scale chamber has realized an average cooling COP of 0.87, with the maximum value of 1.22. Another comparison test for efficacy of PCM thermal storage unit shows that 35.3% electrical energy has been saved from using PCM for the thermoelectric cooling system. In general, PCM faces difficulty of poor thermal conductivity at both solid and liquid phases. This system implemented a finned inner tube to increase heat transfer during PCM charging (melting) process that directly impacts thermoelectric system's performance. A simulation tool for the entire system has been developed including mathematical models for a single thermoelectric module, for the thermoelectric cooling unit, for the PCM thermal storage unit, and for the outdoor air-water heat exchanger. When modeling PCM thermal storage unit, the enthalpy method has been adopted. Since natural convection has been observed in experiments playing a key effect on heat transfer in PCM, a staged effective thermal conductivity (ke) concept and modified Rayleigh (Ra) number formula have been developed to better capture natural convection's variable effects during the PCM charging process. Therefore, a modeling-based design procedure for thermoelectric cooling system integrating with PCM has been proposed. A case study has been completed for a model office room to demonstrate the qualitative and quantitative evaluations to the major system components. Results of this research can be extended to other applications in relevant areas. For instance, the proposed PCM thermal storage unit can be applied to integration with water-cooled conventional air-conditioning devices. Instead of using water cooling, a case study of using the proposed PCM unit for a water-cooled air-conditioner shows a COP increase of more than 25.6%.

Cryotherapy Reinvented: Application of Phase Change Material for Recovery in Elite Soccer.

PubMed

Clifford, Tom; Abbott, Will; Kwiecien, Susan Y; Howatson, Glyn; McHugh, Malachy P

2018-05-01

To examine whether donning lower-body garments fitted with cooled phase change material (PCM) would enhance recovery after a soccer match. In a randomized, crossover design, 11 elite soccer players from the reserve squad of a team in the second-highest league in England wore PCM cooled to 15°C (PCM cold ) or left at ambient temperature (PCM amb ; sham control) for 3 h after a soccer match. To assess recovery, countermovement jump height, maximal isometric voluntary contraction (MIVC), muscle soreness, and the adapted Brief Assessment of Mood Questionnaire (BAM+) were measured before 12, 36, and 60 h after each match. A belief questionnaire was completed preintervention and postintervention to determine the perceived effectiveness of each garment. Results are comparisons between the 2 conditions at each time point postmatch. MIVC at 36 h postmatch was greater with PCM cold versus PCM warm (P = .01; ES = 1.59; 95% CI, 3.9-17.1%). MIVC also tended to be higher at 60 h postmatch (P = .05; ES = 0.85; 95% CI, -0.4% to 11.1%). Muscle soreness was 26.5% lower in PCM cold versus PCM warm at 36 h (P = .02; ES = 1.7; 95% CI, -50.4 to -16.1 mm) and 24.3% lower at 60 h (P = .04; ES = 1.1; 95% CI, -26.9 to -0.874 mm). There were no between-conditions differences in postmatch countermovement jump height or BAM+ (P > .05). The belief questionnaire revealed that players felt the PCM cold was more effective than the PCM amb after the intervention (P = .004). PCM cooling garments provide a practical means of delivering prolonged postexercise cooling and thereby accelerate recovery in elite soccer players.

Interplex modulation and a suppressed-carrier tracking loop for coherent communications systems

NASA Technical Reports Server (NTRS)

Butman, S.; Timor, U.

1974-01-01

Simple addition to hardware and new mode of operation of transmitter and receiver in coherent, PCM/PSK/PM configuration greatly improves channel efficiency. Procedure reduces amount of power lost to intermodulation products.

Aromatase expression is linked to estrogenic sensitivity of periurethral muscles in female rabbits.

PubMed

de los Ángeles Carrasco-Ruiz, María; García-Villamar, Verónica; López-García, Kenia; Sánchez-García, Octavio; Pacheco, Pablo; Cuevas, Estela; Martínez-Gómez, Margarita; Castelán, Francisco

2015-06-01

Beyond its role in the conversion of androgens to estrogens, the expression of aromatase could influence on the estrogenic signalling in targeted tissues. Considering the well-defined biochemical and physiological differences between the pubococcygeus (Pcm) and bulbospongiosus (Bsm) muscles in female rabbits, it is presently hypothesized that the aromatase expression is differentially linked to the estrogen sensitivity of each muscle. To this end, serum estradiol levels and the aromatase expression, presence of ERα and ERβ and morphometry were evaluated in the Pcm and Bsm of female rabbits allocated in control, ovariectomized (OVX) and OVX treated with estradiol benzoate (OVX + EB) groups. Aromatase expression was high in the Pcm. Independently to serum estradiol, ovariectomy increased aromatase expression in the Pcm while decreased it in the Bsm. The EB treatment avoided the effect of ovariectomy only in the Pcm. The number of immunoreactive nuclei anti-ERα and anti-ERβ was high in the Pcm of OVX and OVX + EB rabbits, while those in the Bsm remained unchanged. The number of peripheral nuclei per fibre and the cross-sectional area-to-myonucleus ratio were modified only in the Pcm. Our findings support aromatase expression in the Pcm, and Bsm of rabbits is differentially linked to estrogenic sensitivity of each muscle. Copyright © 2015 John Wiley & Sons, Ltd.

The structure and function of the pericellular matrix of articular cartilage.

PubMed

Wilusz, Rebecca E; Sanchez-Adams, Johannah; Guilak, Farshid

2014-10-01

Chondrocytes in articular cartilage are surrounded by a narrow pericellular matrix (PCM) that is both biochemically and biomechanically distinct from the extracellular matrix (ECM) of the tissue. While the PCM was first observed nearly a century ago, its role is still under investigation. In support of early hypotheses regarding its function, increasing evidence indicates that the PCM serves as a transducer of biochemical and biomechanical signals to the chondrocyte. Work over the past two decades has established that the PCM in adult tissue is defined biochemically by several molecular components, including type VI collagen and perlecan. On the other hand, the biomechanical properties of this structure have only recently been measured. Techniques such as micropipette aspiration, in situ imaging, computational modeling, and atomic force microscopy have determined that the PCM exhibits distinct mechanical properties as compared to the ECM, and that these properties are influenced by specific PCM components as well as disease state. Importantly, the unique relationships among the mechanical properties of the chondrocyte, PCM, and ECM in different zones of cartilage suggest that this region significantly influences the stress-strain environment of the chondrocyte. In this review, we discuss recent advances in the measurement of PCM mechanical properties and structure that further increase our understanding of PCM function. Taken together, these studies suggest that the PCM plays a critical role in controlling the mechanical environment and mechanobiology of cells in cartilage and other cartilaginous tissues, such as the meniscus or intervertebral disc. Copyright © 2014 International Society of Matrix Biology. Published by Elsevier B.V. All rights reserved.

ArtinM offers new perspectives in the development of antifungal therapy

PubMed Central

Ruas, Luciana P.; Carvalho, Fernanda C.; Roque-Barreira, Maria-Cristina

2012-01-01

The thermally dimorphic fungus Paracoccidioides brasiliensis is the causative agent of paracoccidioidomycosis (PCM), the most frequent systemic mycosis that affects the rural populations in Latin America. Despite significant developments in antifungal chemotherapy, its efficacy remains limited since drug therapy is prolonged and associated with toxic side effects and relapses. In response to these challenges, it is now recognized that several aspects of antifungal immunity can be modulated to better deal with fungal infections. A common idea for halting fungal infections has been the need to activate a cell-based, pro-inflammatory Th1 immune response to improve the fungal elimination. ArtinM, a D-mannose binding lectin from Artocarpus heterophyllus, has the property of modulating immunity against several intracellular pathogens. Here, we review the immunomodulatory activity of ArtinM during experimental PCM in mice. Both prophylactic and therapeutic protocols of ArtinM administration promotes a Th1 immune response balanced by IL-10, which outstandingly reduces the fungal load in organs of the treated mice while maintaining a controlled inflammation at the site of infection. A carbohydrate recognition-based interaction of ArtinM with Toll-like receptor 2 (TLR2) accounts for initiating the immunomodulatory effect of the lectin. The precise identification of the TLR2 N-glycan(s) targeted by ArtinM may support novel basis for the development of antifungal therapy. PMID:22715337

A Randomized Comparative Study of Two Techniques to Optimize the Root Coverage Using a Porcine Collagen Matrix.

PubMed

Reino, Danilo Maeda; Maia, Luciana Prado; Fernandes, Patrícia Garani; Souza, Sergio Luis Scombatti de; Taba Junior, Mario; Palioto, Daniela Bazan; Grisi, Marcio Fermandes de Moraes; Novaes, Arthur Belém

2015-10-01

The aim of this randomized controlled clinical study was to compare the extended flap technique (EFT) with the coronally advanced flap technique (CAF) using a porcine collagen matrix (PCM) for root coverage. Twenty patients with two bilateral gingival recessions, Miller class I or II on non-molar teeth were treated with CAF+PCM (control group) or EFT+PCM (test group). Clinical measurements of probing pocket depth (PPD), clinical attachment level (CAL), recession height (RH), keratinized tissue height (KTH), keratinized mucosa thickness (KMT) were determined at baseline, 3 and 6 months post-surgery. At 6 months, the mean root coverage for test group was 81.89%, and for control group it was 62.80% (p<0.01). The change of recession depth from baseline was statistically significant between test and control groups, with an mean of 2.21 mm gained at the control sites and 2.84 mm gained at the test sites (p=0.02). There were no statistically significant differences for KTH, PPD or CAL comparing the two therapies. The extended flap technique presented better root coverage than the coronally advanced flap technique when PCM was used.

Functional and phenotypic evaluation of eosinophils from patients with the acute form of paracoccidioidomycosis.

PubMed

Braga, Fernanda Gambogi; Ruas, Luciana Pereira; Pereira, Ricardo Mendes; Lima, Xinaida Taligare; Antunes, Edson; Mamoni, Ronei Luciano; Blotta, Maria Heloisa Souza Lima

2017-05-01

Eosinophilia is a typical finding of the acute/juvenile form of paracoccidioidomycosis (PCM), a systemic mycosis endemic in Latin America. This clinical form is characterized by depressed cellular immune response and production of Th2 cytokines. Moreover, it has been shown that the increased number of eosinophils in peripheral blood of patients returns to normal values after antifungal treatment. However, the role of eosinophils in PCM has never been evaluated. This study aimed to assess the phenotypic and functional characteristics of eosinophils in PCM. In 15 patients with the acute form of the disease, we detected expression of MBP, CCL5 (RANTES) and CCL11 (eotaxin) in biopsies of lymph nodes and liver. In addition, there were higher levels of chemokines and granule proteins in the peripheral blood of patients compared to controls. Isolation of eosinophils from blood revealed a higher frequency of CD69+ and TLR2+ eosinophils in patients compared to controls, and a lower population of CD80+ cells. We also evaluated the fungicidal capacity of eosinophils in vitro. Our results revealed that eosinophils from PCM patients and controls exhibit similar ability to kill P. brasiliensis yeast cells, although eosinophils of patients were less responsive to IL-5 stimulation than controls. In conclusion, we suggest that eosinophils might play a role in the host response to fungi and in the pathophysiology of PCM by inducing an intense and systemic inflammatory response in the initial phase of the infection.

OA-7 Cargo Module Hatch Closure and Rotate to Vertical at SSPF

NASA Image and Video Library

2017-02-12

In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, the hatch is closed on the Cygnus spacecraft's pressurized cargo module (PCM) for the Orbital ATK CRS-7 mission to the International Space Station. The module is then rotated to vertical for mating to the service module. Scheduled to launch on March 19, 2017, the commercial resupply services mission will lift off atop a United Launch Alliance Atlas V rocket from Space launch Complex 41 at Cape Canaveral Air Force Station.

Hypothyroidism impairs somatovisceral reflexes involved in micturition of female rabbits.

PubMed

Sánchez-García, Octavio; López-Juárez, Rhode; Rodríguez-Castelán, Julia; Corona-Quintanilla, Dora L; Martínez-Gómez, Margarita; Cuevas-Romero, Estela; Castelán, Francisco

2018-04-17

To determine the impact of hypothyroidism on the bladder and urethral functions as well as in the activation of the pubococcygeous (Pcm) and bulbospongiosus (Bsm) during micturition. Age-matched control and methimazole-induced hypothyroid female rabbits were used to simultaneously record cystometrograms, urethral pressure, and the reflex activation of Pcm and Bsm during the induced micturition. Urodynamic and urethral variables were measured. Activation or no activation of the Pcm and Bsm during the storage and voiding phases of micturition were categorized as 1 or 0. Significant differences (P ≤ 0.05) between control and hypothyroid groups were determined with unpaired Student-t or Mann-Whitney tests. One-month induced hypothyroidism increased the residual volume and threshold pressure while the opposite was true for the voided volume, maximal pressure, and voiding efficiency. Urethral pressure was also affected as supported by a notorious augmentation of the urethral resistance, among other changes in the rest of measured variables. Hypothyroidism also affected the reflex activation of the Pcm in the voiding phase of micturition. Our findings demonstrate hypothyroidism impairs the bladder and, urethral functions, and reflex activation of Pcm and Bsm affecting the micturition in female rabbits. © 2018 Wiley Periodicals, Inc.

Development of Hollow Steel Ball Macro-Encapsulated PCM for Thermal Energy Storage Concrete

PubMed Central

Dong, Zhijun; Cui, Hongzhi; Tang, Waiching; Chen, Dazhu; Wen, Haibo

2016-01-01

The application of thermal energy storage with phase change materials (PCMs) for energy efficiency of buildings grew rapidly in the last few years. In this research, octadecane paraffin was served as a PCM, and a structural concrete with the function of indoor temperature control was developed by using a macro-encapsulated PCM hollow steel ball (HSB). The macro-encapsulated PCM-HSB was prepared by incorporation of octadecane into HSBs through vacuum impregnation. Test results showed that the maximum percentage of octadecane carried by HSBs was 80.3% by mass. The macro-encapsulated PCM-HSB has a latent heat storage capacity as high as 200.5 J/g. The compressive strength of concrete with macro-encapsulated PCM-HSB at 28 days ranged from 22 to 40 MPa. The indoor thermal performance test revealed that concrete with macro-encapsulated octadecane-HSB was capable of reducing the peak indoor air temperature and the fluctuation of indoor temperature. It can be very effective in transferring the heating and cooling loads away from the peak demand times. PMID:28787859

Phase Change Material Heat Sink for an ISS Flight Experiment

NASA Technical Reports Server (NTRS)

Quinn, Gregory; Stieber, Jesse; Sheth, Rubik; Ahlstrom, Thomas

2015-01-01

A flight experiment is being constructed to utilize the persistent microgravity environment of the International Space Station (ISS) to prove out operation of a microgravity compatible phase change material (PCM) heat sink. A PCM heat sink can help to reduce the overall mass and volume of future exploration spacecraft thermal control systems (TCS). The program is characterizing a new PCM heat sink that incorporates a novel phase management approach to prevent high pressures and structural deformation that often occur with PCM heat sinks undergoing cyclic operation in microgravity. The PCM unit was made using brazed aluminum construction with paraffin wax as the fusible material. It is designed to be installed into a propylene glycol and water cooling loop, with scaling consistent with the conceptual designs for the Orion Multipurpose Crew Vehicle. This paper reports on the construction of the PCM heat sink and on initial ground test results conducted at UTC Aerospace Systems prior to delivery to NASA. The prototype will be tested later on the ground and in orbit via a self-contained experiment package developed by NASA Johnson Space Center to operate in an ISS EXPRESS rack.

Development of Hollow Steel Ball Macro-Encapsulated PCM for Thermal Energy Storage Concrete.

PubMed

Dong, Zhijun; Cui, Hongzhi; Tang, Waiching; Chen, Dazhu; Wen, Haibo

2016-01-19

The application of thermal energy storage with phase change materials (PCMs) for energy efficiency of buildings grew rapidly in the last few years. In this research, octadecane paraffin was served as a PCM, and a structural concrete with the function of indoor temperature control was developed by using a macro-encapsulated PCM hollow steel ball (HSB). The macro-encapsulated PCM-HSB was prepared by incorporation of octadecane into HSBs through vacuum impregnation. Test results showed that the maximum percentage of octadecane carried by HSBs was 80.3% by mass. The macro-encapsulated PCM-HSB has a latent heat storage capacity as high as 200.5 J/g. The compressive strength of concrete with macro-encapsulated PCM-HSB at 28 days ranged from 22 to 40 MPa. The indoor thermal performance test revealed that concrete with macro-encapsulated octadecane-HSB was capable of reducing the peak indoor air temperature and the fluctuation of indoor temperature. It can be very effective in transferring the heating and cooling loads away from the peak demand times.

Altered distribution of peripheral blood dendritic cell subsets in patients with pulmonary paracoccidioidomycosis.

PubMed

Venturini, James; Cavalcante, Ricardo Souza; Moris, Daniela Vanessa; Golim, Márjorie de Assis; Levorato, Adriele Dandara; Reis, Karoline Hagatha Dos; Arruda, Maria Sueli Parreira de; Mendes, Rinaldo Poncio

2017-09-01

Paracoccidioidomycosis (PCM) is a systemic mycosis caused by fungi from the genus Paracoccidioides in Latin America. PCM-patients (PCM-p) are classified as having acute/subacute or chronic (CF) clinical forms. CF is responsible for 75%-90% of all cases, affects mainly adults over 30 years old and the clinical manifestation are associated mainly with lungs and mucosa of upper airdigestive tract. In addition, the CF patients exhibit fibrosis of the lungs, oral mucous membranes and adrenals, and pulmonary emphysema. Consequently, CF PCM-p with active disease, as well as those that have been apparently cured, seem to be an interesting model for studies aiming to understand the long-term host-fungi relationship and hypoxia. Dendritic cells (DCs) constitute a system that serve as a major link between innate and adaptive immunity composed of several subpopulations of cells including two main subsets: myeloid (mDCs) and plasmacytoid (pDCs). The present study aimed to access the distribution of PBDC subsets of CF PCM-p who were not treated (NT) or treated (apparently cured - AC). CF PCM-p were categorized into two groups, consisting of 9 NTs and 9 ACs. Twenty-one healthy individuals were used as the control group. The determination of the PBDC subsets was performed by FACS (fluorescence-activated cell sorting) and the dosage of serum TNF-α, IL1β, IL-18, CCL3, IL-10 and basic fibroblast growth factor (bFGF) by ELISA (enzyme-linked immunosorbent assay). A high count and percentage of mDCs was observed before treatment, along with a low count of pDCs in treated patients. Furthermore, the mDC:pDC ratio and serum levels of TNF-α was higher in both of the PCM-p groups than in the control group. In conclusion, our findings demonstrated that active PCM influences the distribution of mDCs and pDCs, and after treatment, PCM-p retained a lower count of pDCs associated with pro-inflammatory profile. Therefore, we identified new evidences of persistent immunological abnormalities in PCM-p after treatment. Even these patients showing fungal clearance after successful antifungal treatment; the hypoxia, triggered by the persistent pulmonary sequelae, possibly continues to interfere in the immune response. Copyright © 2017 Elsevier B.V. All rights reserved.

Controllable SET process in O-Ti-Sb-Te based phase change memory for synaptic application

NASA Astrophysics Data System (ADS)

Ren, Kun; Li, Ruiheng; Chen, Xin; Wang, Yong; Shen, Jiabin; Xia, Mengjiao; Lv, Shilong; Ji, Zhenguo; Song, Zhitang

2018-02-01

The nonlinear resistance change and small bit resolution of phase change memory (PCM) under identical operation pulses will limit its performance as a synaptic device. The octahedral Ti-Te units in Ti-Sb-Te, regarded as nucleation seeds, are degenerated when Ti is bonded with O, causing a slower crystallization and a controllable SET process in PCM cells. A linear resistance change under identical pulses, a resolution of ˜8 bits, and an ON/OFF ratio of ˜102 has been achieved in O-Ti-Sb-Te based PCM, showing its potential application as a synaptic device to improve recognition performance of the neural network.

Phase Change Material for Temperature Control of Imager or Sounder on GOES Type Satellites in GEO

NASA Technical Reports Server (NTRS)

Choi, Michael K.

2014-01-01

This paper uses phase change material (PCM) in the scan cavity of an imager or sounder on satellites in geostationary orbit (GEO) to maintain the telescope temperature stable. When sunlight enters the scan aperture, solar heating causes the PCM to melt. When sunlight stops entering the scan aperture, the PCM releases the thermal energy stored to keep the components in the telescope warm. It has no moving parts or bimetallic springs. It reduces heater power required to make up the heat lost by radiation to space through the aperture. It is an attractive thermal control option to a radiator with a louver and a sunshade.

Processing of on-board recorded data for quick analysis of aircraft performance. [rotor systems research aircraft

NASA Technical Reports Server (NTRS)

Michaud, N. H.

1979-01-01

A system of independent computer programs for the processing of digitized pulse code modulated (PCM) and frequency modulated (FM) data is described. Information is stored in a set of random files and accessed to produce both statistical and graphical output. The software system is designed primarily to present these reports within a twenty-four hour period for quick analysis of the helicopter's performance.

A distributed control approach for power and energy management in a notional shipboard power system

NASA Astrophysics Data System (ADS)

Shen, Qunying

The main goal of this thesis is to present a power control module (PCON) based approach for power and energy management and to examine its control capability in shipboard power system (SPS). The proposed control scheme is implemented in a notional medium voltage direct current (MVDC) integrated power system (IPS) for electric ship. To realize the control functions such as ship mode selection, generator launch schedule, blackout monitoring, and fault ride-through, a PCON based distributed power and energy management system (PEMS) is developed. The control scheme is proposed as two-layer hierarchical architecture with system level on the top as the supervisory control and zonal level on the bottom as the decentralized control, which is based on the zonal distribution characteristic of the notional MVDC IPS that was proposed as one of the approaches for Next Generation Integrated Power System (NGIPS) by Norbert Doerry. Several types of modules with different functionalities are used to derive the control scheme in detail for the notional MVDC IPS. Those modules include the power generation module (PGM) that controls the function of generators, the power conversion module (PCM) that controls the functions of DC/DC or DC/AC converters, etc. Among them, the power control module (PCON) plays a critical role in the PEMS. It is the core of the control process. PCONs in the PEMS interact with all the other modules, such as power propulsion module (PPM), energy storage module (ESM), load shedding module (LSHED), and human machine interface (HMI) to realize the control algorithm in PEMS. The proposed control scheme is implemented in real time using the real time digital simulator (RTDS) to verify its validity. To achieve this, a system level energy storage module (SESM) and a zonal level energy storage module (ZESM) are developed in RTDS to cooperate with PCONs to realize the control functionalities. In addition, a load shedding module which takes into account the reliability of power supply (in terms of quality of service) is developed. This module can supply uninterruptible power to the mission critical loads. In addition, a multi-agent system (MAS) based framework is proposed to implement the PCON based PEMS through a hardware setup that is composed of MAMBA boards and FPGA interface. Agents are implemented using Java Agent DEvelopment Framework (JADE). Various test scenarios were tested to validate the approach.

Functional and phenotypic evaluation of eosinophils from patients with the acute form of paracoccidioidomycosis

PubMed Central

Braga, Fernanda Gambogi; Ruas, Luciana Pereira; Pereira, Ricardo Mendes; Lima, Xinaida Taligare; Antunes, Edson; Mamoni, Ronei Luciano

2017-01-01

Background Eosinophilia is a typical finding of the acute/juvenile form of paracoccidioidomycosis (PCM), a systemic mycosis endemic in Latin America. This clinical form is characterized by depressed cellular immune response and production of Th2 cytokines. Moreover, it has been shown that the increased number of eosinophils in peripheral blood of patients returns to normal values after antifungal treatment. However, the role of eosinophils in PCM has never been evaluated. This study aimed to assess the phenotypic and functional characteristics of eosinophils in PCM. Methods/Principal findings In 15 patients with the acute form of the disease, we detected expression of MBP, CCL5 (RANTES) and CCL11 (eotaxin) in biopsies of lymph nodes and liver. In addition, there were higher levels of chemokines and granule proteins in the peripheral blood of patients compared to controls. Isolation of eosinophils from blood revealed a higher frequency of CD69+ and TLR2+ eosinophils in patients compared to controls, and a lower population of CD80+ cells. We also evaluated the fungicidal capacity of eosinophils in vitro. Our results revealed that eosinophils from PCM patients and controls exhibit similar ability to kill P. brasiliensis yeast cells, although eosinophils of patients were less responsive to IL-5 stimulation than controls. Conclusion/Principal findings In conclusion, we suggest that eosinophils might play a role in the host response to fungi and in the pathophysiology of PCM by inducing an intense and systemic inflammatory response in the initial phase of the infection. PMID:28489854

Phase change material based tunable reflectarray for free-space optical inter/intra chip interconnects.

PubMed

Zou, Longfang; Cryan, Martin; Klemm, Maciej

2014-10-06

The concept of phase change material (PCM) based optical antennas and antenna arrays is proposed for dynamic beam shaping and steering utilized in free-space optical inter/intra chip interconnects. The essence of this concept lies in the fact that the behaviour of PCM based optical antennas will change due to the different optical properties of the amorphous and crystalline state of the PCM. By engineering optical antennas or antenna arrays, it is feasible to design dynamic optical links in a desired manner. In order to illustrate this concept, a PCM based tunable reflectarray is proposed for a scenario of a dynamic optical link between a source and two receivers. The designed reflectarray is able to switch the optical link between two receivers by switching the two states of the PCM. Two types of antennas are employed in the proposed tunable reflectarray to achieve full control of the wavefront of the reflected beam. Numerical studies show the expected binary beam steering at the optical communication wavelength of 1.55 μm. This study suggests a new research area of PCM based optical antennas and antenna arrays for dynamic optical switching and routing.

Radiosensitivities of bacterial isolates on minced chicken and poached chicken meal and their elimination following irradiation and chilled storage

NASA Astrophysics Data System (ADS)

Adu-Gyamfi, A.; Nketsia-Tabiri, J.; Apea Bah, F.

2008-02-01

The radiosensitivities of Escherichia coli and Staphylococcus aureus on poached chicken meal (PCM) and minced chicken substrate (MCS) were determined. Effect of irradiation (0, 1, 2 kGy) on total viable cells (TVC) of PCM components was determined under chilled (3-5 °C) storage (0, 9, 14, 21 days) and challenge testing of the bacterial isolates with irradiation (0, 2, 3 kGy) was also conducted on PCM under chilled storage (0,7, 14, 21, 28 days). Additionally, sensory evaluation of the PCM components was assessed with irradiation (0, 2, 3 kGy) during chilled storage (0, 7, 14, 21 days). D10 of E. coli on PCM and MCS were 0.18 and 0.25 kGy whiles those of S. aureus were 0.27 and 0.29 kGy, respectively. D10 values for PCM E. coli. 2 kGy controlled TVC and extended the shelf life of meals to ⩾14 days but 3 kGy was required to eliminate E. coli and S. aureus. Sensory qualities of the meal were not affected by an irradiation dose of 3 kGy.

PCM1 is recruited to the centrosome by the cooperative action of DISC1 and BBS4 and is a candidate for psychiatric illness

PubMed Central

Kamiya, Atsushi; Tan, Perciliz L.; Kubo, Ken-ichiro; Engelhard, Caitlin; Ishizuka, Koko; Kubo, Akiharu; Tsukita, Sachiko; Pulver, Ann E.; Nakajima, Kazunori; Cascella, Nicola G.; Katsanis, Nicholas; Sawa, Akira

2009-01-01

Context A role for the centrosome has been suggested in the pathology of major mental illnesses, especially schizophrenia (SZ). Objectives To show that pericentriolar material-1 protein (PCM1) forms a complex at the centrosome with Disrupted-In-Schizophrenia-1 (DISC1) and Bardet-Biedl syndrome-4 protein (BBS4), which provides a crucial pathway for cortical development associated with the pathology of SZ. To identify mutations in the PCM1 gene in a SZ population. Design Interaction of DISC1, PCM1, and BBS proteins was assessed by immunofluorescent staining and co-immunoprecipitation. Effects of PCM1, DISC1, and BBS on centrosomal functions and corticogenesis in vivo were tested by RNAi. PCM1 gene was examined by sequencing 39 exons and flanking splice sites. Setting and Patients Thirty-two probands with SZ from families that had excess allele sharing among affected individuals at 8p22, and 219 Caucasian controls. Main Outcome Measures Protein interaction and recruitment at the centrosome in cells; neuronal migration in the cerebral cortex; variant discovery in PCM1 in SZ patients. Results PCM1 forms a complex with DISC1 and BBS4 through discrete binding domains in each protein. DISC1 and BBS4 are required for targeting PCM1 and other cargo proteins, such as ninein, to the centrosome in a synergistic manner. In the developing cerebral cortex, suppression of PCM1 leads to neuronal migration defects, which are phenocopied by the suppression of either DISC1 or BBS4, and are exacerbated by the concomitant suppression of both. Furtheremore, a nonsense mutation that segregates with schizophrenia-spectrum psychosis is found in one family. Conclusion Our data further support for the role of centrosomal proteins in cortical development and suggest that perturbation of centrosomal function contributes to the development of mental diseases including SZ. PMID:18762586

Single closed contact for 0.18-micron photolithography process

NASA Astrophysics Data System (ADS)

Cheung, Cristina; Phan, Khoi A.; Chiu, Robert J.

2000-06-01

With the rapid advances of deep submicron semiconductor technology, identifying defects is converted into a challenge for different modules in the fabrication of chips. Yield engineers often do bitmap on a memory circuit array (SRAM) to identify the failure bits. This is followed by a wafer stripback to look for visual defects at each deprocessed layer for feedback to the Fab. However, to identify the root cause of a problem, Fab engineers must be able to detect similar defects either on the product wafers in process or some short loop test wafers. In the photolithography process, we recognize that the detection of defects is becoming as important as satisfying the critical dimension (CD) of the device. For a multi-level metallization chemically mechanical polish backend process, it is very difficult to detect missing contacts or via at the masking steps due to metal grain roughness, film color variation and/or previous layer defects. Often, photolithography engineer must depend on Photo Cell Monitor (PCM) and short loop experiments for controlling baseline defects and improvement. In this paper, we discuss the findings on the Poly mask PCM and the Contact mask PCM. We present the comparison between the Poly mask and the Contact mask of the I-line Phase Shifted Via mask and DUV mask process for a 0.18 micron process technology. The correlation and the different type of defects between the Contact PCM and the Poly Mask are discussed. The Contact PCM was found to be more sensitive and correlated to contact failure at sort yield better. We also dedicate to study the root cause of a single closed contact hole in the Contact mask short loop experiment for a 0.18 micron process technology. A single closed contact defect was often caused by the developer process, such as bubbles in the line, resist residue left behind, and the rinse mechanism. We also found surfactant solution helps to improve the surface tension of the wafer for the developer process and this prevents/eliminates a single closed contact hole defects. The applications and effects of using different substrates like SiON, different thicknesses of Oxides, and Poly in the Contact Photo Mask is shown. Finally, some defect troubleshooting techniques and the root cause analysis are also discussed.

75 FR 30103 - Petition for Exemption From the Vehicle Theft Prevention Standard; Ford Motor Company

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... (BCM), the PEP/RFA module and the PCM. Ford pointed out that in addition to the programmed key, the... concludes that the device will provide four of the five types of performance listed in Sec. 543.6(a)(3...

Biotelemetry system for ambulatory patients

NASA Technical Reports Server (NTRS)

Fryer, T. B.

1978-01-01

Compact transmitter for multichannel telemetry of medical data is carried in patient's belt. Pulse-code modulation (PCM), is used for high-quality signal, and low-power CMOS integrated circuits make miniaturization possible. Transmitter is useful for electro-encephalograms (EEG) and electro-cardiograms (EKG) and other biomedical patient-monitoring situations.

Using Paraffin PCM to Make Optical Communication Type of Payloads Thermally Self-Sufficient for Operation in Orion Crew Module

NASA Technical Reports Server (NTRS)

Choi, Michael K.

2016-01-01

An innovative concept of using paraffin phase change material with a melting point of 28 C to make Optical Communication type of payload thermally self-sufficient for operation in the Orion Crew Module is presented. It stores the waste heat of the payload and permits it to operate for about one hour by maintaining its temperature within the maximum operating limit. It overcomes the problem of relying on the availability of cold plate heat sink in the Orion Crew Module.

Long Duration Exposure Facility (LDEF) low-temperature Heat Pipe Experiment Package (HEPP) flight results

NASA Technical Reports Server (NTRS)

Mcintosh, Roy; Mccreight, Craig; Brennan, Patrick J.

1992-01-01

The Low Temperature Heat Pipe Flight Experiment (HEPP) is a fairly complicated thermal control experiment that was designed to evaluate the performance of two different low temperature ethane heat pipes and a n-Heptane Phase Change Material (PCM) canister. A total of 388 days of continuous operation with an axially grooved aluminum fixed conductance heat pipe of axially grooved stainless steel heat pipe diode was demonstrated before the EDS batteries lost power. The inability of the HEPP's radiator to cool below 190 K in flight prevented freezing of the PCM and the opportunity to conduct transport tests with the heat pipes. Post flight tests showed that the heat pipes and the PCM are still functioning. This paper presents a summary of the flight data analysis for the HEPP and its related support systems. Pre and post-flight thermal vacuum tests results are presented for the HEPP thermal control system along with individual heat pipe performance and PCM behavior. Appropriate SIG related systems data will also be included along with a 'lessons learned' summary.

106-17 Telemetry Standards Metadata Configuration Chapter 23

DTIC Science & Technology

2017-07-01

23-1 23.2 Metadata Description Language ...Chapter 23, July 2017 iii Acronyms HTML Hypertext Markup Language MDL Metadata Description Language PCM pulse code modulation TMATS Telemetry...Attributes Transfer Standard W3C World Wide Web Consortium XML eXtensible Markup Language XSD XML schema document Telemetry Network Standard

Analysis of a Delayed Delta Modulator.

DTIC Science & Technology

1983-05-01

parallels that of Janardhanan [10] for DPCM with matched integra- tion of stationary first-order Gauss-Markov input. In Subsection A the limiting...181, 1978. [10] JANARDHANAN , E., "Differential PCM -ystems", IEEE Trans. Conmmun., vol. Com-27, pp. 82-93, 1979. [111 KANTOROVICI, L.V. and KRYLOV, V.I

Atomic entanglement purification and concentration using coherent state input-output process in low-Q cavity QED regime.

PubMed

Cao, Cong; Wang, Chuan; He, Ling-Yan; Zhang, Ru

2013-02-25

We investigate an atomic entanglement purification protocol based on the coherent state input-output process by working in low-Q cavity in the atom-cavity intermediate coupling region. The information of entangled states are encoded in three-level configured single atoms confined in separated one-side optical micro-cavities. Using the coherent state input-output process, we design a two-qubit parity check module (PCM), which allows the quantum nondemolition measurement for the atomic qubits, and show its use for remote parities to distill a high-fidelity atomic entangled ensemble from an initial mixed state ensemble nonlocally. The proposed scheme can further be used for unknown atomic states entanglement concentration. Also by exploiting the PCM, we describe a modified scheme for atomic entanglement concentration by introducing ancillary single atoms. As the coherent state input-output process is robust and scalable in realistic applications, and the detection in the PCM is based on the intensity of outgoing coherent state, the present protocols may be widely used in large-scaled and solid-based quantum repeater and quantum information processing.

M2 macrophages and inflammatory cells in oral lesions of chronic paracoccidioidomycosis.

PubMed

de Carli, Marina Lara; Miyazawa, Marta; Nonogaki, Suely; Shirata, Neuza Kasumi; Oliveira, Denise Tostes; Pereira, Alessandro Antônio Costa; Hanemann, João Adolfo Costa

2016-02-01

Paracoccidioidomycosis (PCM) is a systemic fungal infection caused by Paracoccidioides brasiliensis (Pb) and associated with deficient cellular immune response, which is modulated by inflammatory cells, mainly macrophages, and cytokines. Recently, the comprehension of the macrophage polarization mediated by Th1 and Th2 cytokines has contributed to elucidate the immune response that takes part in some diseases. Thus, the aim of this study was to assess the presence of Th1- and Th2-immune response and also Pb counting in oral lesions of chronic PCM. Forty-eight cases of chronic PCM oral lesions were included. All cases were classified as loose or dense granulomas. S100 protein, IL-1β, IL-6, TNF-α, CD163 and CD68 immunoexpressions, and Pb localization were evaluated. The fungi present in the tissue were quantified by anti-Pb antibody. Most patients were white men with mean age of 47 years old and showed higher incidence of multiple lesions. Loose granulomas were predominant and exhibited a great amount of M2 macrophages, which were visualized with anti-CD163 antibody. The expression for CD163 and CD68 was similar (P = 0.05), highlighting the predominance of M2 macrophages in PCM. IL-1β, IL-6, and TNF-α immunoexpression did not significantly change with CD163, CD68, and S100 protein. The number of fungi was significantly higher in cases with intense IL-1β immunoexpression (P = 0.003). M2-activated macrophages were the majority among inflammatory cells in chronic PCM, characterizing the action of a Th2-immune response. Nevertheless, Th1 cytokines were also found; mainly IL-1β, which was associated with fungi counting in oral lesions. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

OA-7 Cargo Module Loading

NASA Image and Video Library

2017-02-07

In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, thousands of pounds of supplies, equipment and scientific research materials are prepared for loading aboard a Cygnus spacecraft's pressurized cargo module (PCM) for the Orbital ATK CRS-7 mission to the International Space Station. Scheduled to launch on March 19, 2017, the commercial resupply services mission will lift off atop a United Launch Alliance Atlas V rocket from Space launch Complex 41 at Cape Canaveral Air Force Station.

Reconfigurable Antenna Aperture with Optically Controlled GeTe-Based RF Switches

DTIC Science & Technology

2015-03-31

duration (~100ns) but high amplitude raises the material’s temperature above the melting point . As a liquid, the atoms are randomly distributed...100ns, there is sufficient optical energy to heat and melt a 100nm thick GeTe PCM area of approximately 3µm 2 . Figure 3. Optimum PCM area...which tracks well with previously published thin film heater model [9]. Figure 4. Validation of Melt /Quench Thermal Model Optical Control: The

Phoenix dactylifera protects against oxidative stress and hepatic injury induced by paracetamol intoxication in rats.

PubMed

Salem, Gamal A; Shaban, Ahmed; Diab, Hussain A; Elsaghayer, Wesam A; Mjedib, Manal D; Hnesh, Aomassad M; Sahu, Ravi P

2018-05-16

The current studies were sought to determine effects of antioxidant potential of aqueous and methanolic extracts of Phoenix dactylifera leaves (PLAE and PLME) against the widely-used analgesic paracetamol (PCM) induced hepatotoxicity. Groups of rats were treated with or without PCM (1500 mg/kg), PLAE and PLME (300 mg/kg) and n-acetylcysteine (NAC, 50 mg/kg) followed by assessments of liver function tests, oxidative stress, antioxidant defenses, and hepatotoxicity. We observed that PCM significantly elevated serum liver markers, aspartate aminotransferase (AST), alanine aminotransferase (ALT), alkaline phosphatase (ALP), gamma glutamyl transferase (GGT), and bilirubin compared to control (untreated) group. These PCM-induced effects were associated with oxidative stress as demonstrated by increased levels of malondialdehyde (MDA) and reduced levels of hepatic antioxidant enzymes, glutathione peroxidase (GPx), catalase (CAT), and superoxide dismutase (SOD). Pretreatment of PLME decreased ALT and AST by 78.2% and tissue MDA by 54.1%, and increased hepatic GPx (3.5 folds), CAT (7 folds) and SOD (2.5 folds) compared to PCM group. These PLME-mediated effects were comparable to NAC pretreatment. Histological analysis demonstrates that PLME conserved hepatic tissues against lesions such as inflammation, centrilobular necrosis, and hemorrhages induced by PCM. In contrast, PLAE-mediated effects were less effective in reducing levels of liver function enzymes, oxidative stress, and liver histopathological profiles, and restoring antioxidant defenses against PCM-induced intoxication. These findings indicate that PLME exerts protective effects against PCM-induced hepatotoxicity via scavenging free radicals and restoring hepatic antioxidant enzymes. Thus, PLME and its bioactive components could further be evaluated for their pharmacological properties against drug-induced deleterious effects. Copyright © 2018. Published by Elsevier Masson SAS.

Space shuttle heat pipe thermal control systems

NASA Technical Reports Server (NTRS)

Alario, J.

1973-01-01

Heat pipe (HP) thermal control systems designed for possible space shuttle applications were built and tested under this program. They are: (1) a HP augmented cold rail, (2) a HP/phase change material (PCM) modular heat sink and (3) a HP radiating panel for compartment temperature control. The HP augmented cold rail is similar to a standard two-passage fluid cold rail except that it contains an integral, centrally located HP throughout its length. The central HP core helps to increase the local power density capability by spreading concentrated heat inputs over the entire rail. The HP/PCM modular heat sink system consists of a diode HP connected in series to a standard HP that has a PCM canister attached to its mid-section. It is designed to connect a heat source to a structural heat sink during normal operation, and to automatically decouple from it and sink to the PCM whenever structural temperatures are too high. The HP radiating panel is designed to conductively couple the panel feeder HPs directly to a fluid line that serves as a source of waste heat. It is a simple strap-on type of system that requires no internal or external line modifications to distribute the heat to a large radiating area.

Environmental Control Unit with Integral Thermal Storage

DTIC Science & Technology

2014-06-12

integrated PCM Heat Exchanger (PHX) to provide thermal energy storage . By storing thermal energy during the hottest part of the day and rejecting this stored...Environmental Control Unit (ECU) that uses an integrated PCM Heat Exchanger (PHX) to provide thermal energy storage . To aid in the development of the PHX...Thermal Storage 5a. CONTRACT NUMBER W911QX-14-C-0014 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Michael C. Ellis Ryan McDevitt 5d

Computer program design specifications for the Balloon-borne Ultraviolet Stellar Spectrometer (BUSS) science data decommutation program (BAPS48)

NASA Technical Reports Server (NTRS)

Rodriguez, R. M.

1975-01-01

The Balloon-Borne Ultraviolet Stellar Spectrometer (BUSS) Science Data Docummutation Program (BAPS48) is a pulse code modulation docummutation program that will format the BUSS science data contained on a one inch PCM tracking tape into a seven track serial bit stream formatted digital tape.

The dry-heat loss effect of melt-spun phase change material fibres.

PubMed

Tjønnås, Maria Suong; Færevik, Hilde; Sandsund, Mariann; Reinertsen, Randi E

2015-01-01

Phase change materials (PCM) have the ability to store latent heat when they change phases, a property that gives clothing that incorporates PCM its cooling effect. This study investigated the effect of dry-heat loss (cooling) of a novel melt-spun PCM fibre on the basis of the area covered, mass, the latent heat of fusion and melting temperature, compared to a known PCM clothing product. PCM fibres with melting temperatures of 28.4 and 32.0°C and PCM packs with melting temperatures of 28.0 and 32.0°C were studied. The results showed that the PCM fibres had a larger initial peak cooling effect than that of the PCM packs. The duration of the cooling effect of PCM fibres was primarily dependent on the PCM mass and the latent heat of fusion capacity, and secondly on the covered area and melting temperature of the PCM. This study investigates the cooling effect of PCM fibres on a thermal manikin. The PCM fibres had a high but short-lasting cooling effect. This study contributes to the knowledge of how the body's temperature regulation may be affected by the cooling properties of clothing that incorporates PCM.

Numerical analysis of phase change materials for thermal control of power battery of high power dissipations

NASA Astrophysics Data System (ADS)

Xia, X.; Zhang, H. Y.; Deng, Y. C.

2016-08-01

Solid-fluid phase change materials have been of increasing interest in various applications due to their high latent heat with minimum volume change. In this work, numerical analysis of phase change materials is carried out for the purpose of thermal control of the cylindrical power battery cells for applications in electric vehicles. Uniform heat density is applied at the battery cell, which is surrounded by phase change material (PCM) of paraffin wax type and contained in a metal housing. A two-dimensional geometry model is considered due to the model symmetry. The effects of power densities, heat transfer coefficients and onset melting temperatures are examined for the battery temperature evolution. Temperature plateaus can be observed from the present numerical analysis for the pure PCM cases, with the temperature level depending on the power densities, heat transfer coefficients, and melting temperatures. In addition, the copper foam of high thermal conductivity is inserted into the copper foam to enhance the heat transfer. In the modeling, the local thermal non-equilibrium between the metal foam and the PCM is taken into account and the temperatures for the metal foam and PCM are obtained respectively.

Continuous adaptive beam pointing and tracking for laser power transmission.

PubMed

Schäfer, Christian A

2010-06-21

The adaptive beam pointing concept has been revisited for the purpose of controlled transmission of laser energy from an optical transmitter to a target. After illumination, a bidirectional link is established by a retro-reflector on the target and an amplifier-phase conjugate mirror (A-PCM) on the transmitter. By setting the retro-reflector's aperture smaller than the diffraction limited spot size but big enough to provide sufficient amount of optical feedback, a stable link can be maintained and light that hits the retro-reflector's surrounded area can simultaneously be reconverted into usable electric energy. The phase conjugate feedback ensures that amplifier's distortions are compensated and the target tracked accurately.After deriving basic arithmetic expressions for the proposed system, a section is devoted for the motivation of free-space laser power transmission which is supposed to find varied applicability in space. As an example, power transmission from a satellite to the earth is described where recently proposed solar power generating structures on high-altitudes receive the power above the clouds to provide constant energy supply.In the experimental part, an A-PCM setup with reflectivity of about R(A-PCM) = 100 was realized using a semiconductor optical amplifier and a photorefractive self-pumped PCM. Simulation results show that a reflectivity of R(A-PCM)>1000 could be obtained by improving the self-pumped PCM's efficiency. That would lead to a transmission efficiency of eta>90%.

Passive control of temperature excursion and uniformity in high-energy Li-ion battery packs at high current and ambient temperature

NASA Astrophysics Data System (ADS)

Kizilel, R.; Lateef, A.; Sabbah, R.; Farid, M. M.; Selman, J. R.; Al-Hallaj, S.

A strategy for portable high-power applications with a controlled thermal environment has been developed and has demonstrated the advantage of using the novel phase change material (PCM) thermal management systems over conventional active cooling systems. A passive thermal management system using PCM for Li-ion batteries is tested for extreme conditions, such as ambient temperature of 45 °C and discharge rate of 2.08 C-rate (10 A). Contrary to Li-ion packs without thermal management system, high-energy packs with PCM are discharged safely at high currents and degrading rate of capacity of the Li-ion packs lowered by half. Moreover, the compactness of the packs not only decreases the volume occupied by the packs and its associated complex cooling system, but also decreases the total weight for large power application.

A novel thermal management system for improving discharge/charge performance of Li-ion battery packs under abuse

NASA Astrophysics Data System (ADS)

Arora, Shashank; Kapoor, Ajay; Shen, Weixiang

2018-02-01

Parasitic load, which describes electrical energy consumed by battery thermal management system (TMS), is an important design criterion for battery packs. Passive TMSs using phase change materials (PCMs) are thus generating much interest. However, PCMs suffer from low thermal conductivities. Most current thermal conductivity enhancement techniques involve addition of foreign particles to PCMs. Adding foreign particles increases effective thermal conductivity of PCM-systems but at expense of their latent heat capacity. This paper presents an alternate approach for improving thermal performance of PCM-based TMSs. The introduced technique involves placing battery cells in a vertically inverted position within the battery-pack. It is demonstrated through experiments that inverted cell-layout facilitates build-up of convection current in the pack, which in turn minimises thermal variations within the PCM matrix by enabling PCM mass transfer between the top and the bottom regions of the battery pack. The proposed system is found capable of maintaining tight control over battery cell temperature even during abusive usage, defined as high-rate repetitive cycling with minimal rest periods. In addition, this novel TMS can recover waste heat from PCM-matrix through thermoelectric devices, thereby resulting in a negative parasitic load for TMS.

A multi-controlled drug delivery system based on magnetic mesoporous Fe3O4 nanopaticles and a phase change material for cancer thermo-chemotherapy

NASA Astrophysics Data System (ADS)

Zhang, Qi; Liu, Jian; Yuan, Kunjie; Zhang, Zhengguo; Zhang, Xiaowen; Fang, Xiaoming

2017-10-01

Herein a novel multi-controlled drug release system for doxorubicin (DOX) was developed, in which monodisperse mesoporous Fe3O4 nanoparticles were combined with a phase change material (PCM) and polyethylene glycol 2000 (PEG2000). It is found that the PCM/PEG/DOX mixture containing 20% PEG could be dissolved into water at 42 °C. The mesoporous Fe3O4 nanoparticles prepared by the solvothermal method had sizes of around 25 nm and exhibited a mesoporous microstructure. A simple solvent evaporation process was employed to load the PCM/PEG/DOX mixture on the mesoporous Fe3O4 nanoparticles completely. In the Fe3O4@PCM/PEG/DOX system, the pores of the Fe3O4 nanoparticles were observed to be filled with the mixture of PCM/PEG/DOX. The Fe3O4@PCM/PEG/DOX system showed a saturation magnetization value of 50.0 emu g-1, lower than 71.1 emu g-1 of the mesoporous Fe3O4 nanoparticles, but it was still high enough for magnetic targeting and hyperthermia application. The evaluation on drug release performance indicated that the Fe3O4@PCM/PEG/DOX system achieved nearly zero release of DOX in vitro in body temperature, while around 80% of DOX could be released within 1.5 h at the therapeutic threshold of 42 °C or under the NIR laser irradiation for about 4 h. And a very rapid release of DOX was achieved by this system when applying an alternating magnetic field. By comparing the systems with and without PEG2000, it is revealed that the presence of PEG2000 makes DOX easy to be released from 1-tetradecanol to water, owing to its functions of increasing the solubility of DOX in 1-tetradecanol as well as decreasing the surface tension between water and 1-tetradecanol. The novel drug release system shows great potential for the development of thermo-chemotherapy of cancer treatment.

Test Methods for Telemetry Systems and Subsystems. Volume 5: Test Methods for Digital Recorder/Reproducer Systems and Recorder Memory Modules

DTIC Science & Technology

2016-09-26

serial communications program ( Hyper terminal) Configure METS for PCM 1 Mbps and MIL-STD-1553 10-Hz rate 4 Configure the host software to...Verify recorder stopped 44 Issue . LOOP . Verify recorder goes into record and play in read after write mode 45 Issue .STOP, Verify recorder

Optical Switching Using Transition from Dipolar to Charge Transfer Plasmon Modes in Ge2Sb2Te5 Bridged Metallodielectric Dimers

PubMed Central

Ahmadivand, Arash; Gerislioglu, Burak; Sinha, Raju; Karabiyik, Mustafa; Pala, Nezih

2017-01-01

Capacitive coupling and direct shuttling of charges in nanoscale plasmonic components across a dielectric spacer and through a conductive junction lead to excitation of significantly different dipolar and charge transfer plasmon (CTP) resonances, respectively. Here, we demonstrate the excitation of dipolar and CTP resonant modes in metallic nanodimers bridged by phase-change material (PCM) sections, material and electrical characteristics of which can be controlled by external stimuli. Ultrafast switching (in the range of a few nanoseconds) between amorphous and crystalline phases of the PCM section (here Ge2Sb2Te5 (GST)) allows for designing a tunable plasmonic switch for optical communication applications with significant modulation depth (up to 88%). Judiciously selecting the geometrical parameters and taking advantage of the electrical properties of the amorphous phase of the GST section we adjusted the extinction peak of the dipolar mode at the telecommunication band (λ~1.55 μm), which is considered as the OFF state. Changing the GST phase to crystalline via optical heating allows for direct transfer of charges through the junction between nanodisks and formation of a distinct CTP peak at longer wavelengths (λ~1.85 μm) far from the telecommunication wavelength, which constitutes the ON state. PMID:28205643

Optical Switching Using Transition from Dipolar to Charge Transfer Plasmon Modes in Ge2Sb2Te5 Bridged Metallodielectric Dimers.

PubMed

Ahmadivand, Arash; Gerislioglu, Burak; Sinha, Raju; Karabiyik, Mustafa; Pala, Nezih

2017-02-16

Capacitive coupling and direct shuttling of charges in nanoscale plasmonic components across a dielectric spacer and through a conductive junction lead to excitation of significantly different dipolar and charge transfer plasmon (CTP) resonances, respectively. Here, we demonstrate the excitation of dipolar and CTP resonant modes in metallic nanodimers bridged by phase-change material (PCM) sections, material and electrical characteristics of which can be controlled by external stimuli. Ultrafast switching (in the range of a few nanoseconds) between amorphous and crystalline phases of the PCM section (here Ge 2 Sb 2 Te 5 (GST)) allows for designing a tunable plasmonic switch for optical communication applications with significant modulation depth (up to 88%). Judiciously selecting the geometrical parameters and taking advantage of the electrical properties of the amorphous phase of the GST section we adjusted the extinction peak of the dipolar mode at the telecommunication band (λ~1.55 μm), which is considered as the OFF state. Changing the GST phase to crystalline via optical heating allows for direct transfer of charges through the junction between nanodisks and formation of a distinct CTP peak at longer wavelengths (λ~1.85 μm) far from the telecommunication wavelength, which constitutes the ON state.

Optical Switching Using Transition from Dipolar to Charge Transfer Plasmon Modes in Ge2Sb2Te5 Bridged Metallodielectric Dimers

NASA Astrophysics Data System (ADS)

Ahmadivand, Arash; Gerislioglu, Burak; Sinha, Raju; Karabiyik, Mustafa; Pala, Nezih

2017-02-01

Capacitive coupling and direct shuttling of charges in nanoscale plasmonic components across a dielectric spacer and through a conductive junction lead to excitation of significantly different dipolar and charge transfer plasmon (CTP) resonances, respectively. Here, we demonstrate the excitation of dipolar and CTP resonant modes in metallic nanodimers bridged by phase-change material (PCM) sections, material and electrical characteristics of which can be controlled by external stimuli. Ultrafast switching (in the range of a few nanoseconds) between amorphous and crystalline phases of the PCM section (here Ge2Sb2Te5 (GST)) allows for designing a tunable plasmonic switch for optical communication applications with significant modulation depth (up to 88%). Judiciously selecting the geometrical parameters and taking advantage of the electrical properties of the amorphous phase of the GST section we adjusted the extinction peak of the dipolar mode at the telecommunication band (λ~1.55 μm), which is considered as the OFF state. Changing the GST phase to crystalline via optical heating allows for direct transfer of charges through the junction between nanodisks and formation of a distinct CTP peak at longer wavelengths (λ~1.85 μm) far from the telecommunication wavelength, which constitutes the ON state.

IL-6/STAT3 signaling pathway is activated in plasma cell mastitis.

PubMed

Liu, Yang; Zhang, Jian; Zhou, Yu-Hui; Jiang, Yi-Na; Zhang, Wei; Tang, Xiao-Jiang; Ren, Yu; Han, Shui-Ping; Liu, Pei-Jun; Xu, Jing; He, Jian-Jun

2015-01-01

Plasma cell mastitis (PCM), a particular type of mastitis, mainly occurs in females at nonpregnant and nonlactating stages. The infiltration of abundant plasma cells and lymphocytes is the hallmark of the disease. The incidence rate of PCM increased gradually and its pathogenesis remained unclear. In this study, we investigated the expression of IL-6/STAT3 signaling pathway, which is vital not only for the differentiation of plasma cells but also for survival of plasma cells and T lymphocytes, in 30 PCM cases, 10 acute mastitis cases and 10 normal breast tissues by immunohistochemical analysis. IL-6 level was significantly higher in PCM patients than in acute mastitis patients or normal group. The positive rate of IL-6 and p-STAT3 staining in PCM samples was 93.3% (28/30) and 70% (21/30), respectively, and there was a significant positive association between IL-6 and p-STAT3 staining (r=0.408, P=0.025). In PCM group, the rate of nipple retraction was 40% (12/30). Significantly higher IL-6 expression was found in PCM patients with nipple retraction than in other PCM patients. However, no significant difference in IL-6 or p-STAT3 staining was detected between PCM patients experiencing recurrence and other PCM patients. In addition, Bcl-2 level was higher in PCM patients than in acute mastitis patients or normal group, but there was no difference in Bcl-2 immunostaining between PCM patients experiencing recurrence and other PCM patients. These indicate that IL-6/STAT3 signaling is activated in PCM and may play an important role in the pathogenesis of PCM.

Phase Change Material Heat Exchanger Life Test

NASA Technical Reports Server (NTRS)

Lillibridge, Sean; Stephan, Ryan; Lee, Steve; He, Hung

2008-01-01

Low Lunar Orbit (LLO) poses unique thermal challenges for the orbiting space craft, particularly regarding the performance of the radiators. The emitted infrared (IR) heat flux from the lunar surface varies drastically from the light side to the dark side of the moon. Due to the extremely high incident IR flux, especially at low beta angles, a radiator is oftentimes unable to reject the vehicle heat load throughout the entire lunar orbit. One solution to this problem is to implement Phase Change Material (PCM) Heat Exchangers. PCM Heat Exchangers act as a "thermal capacitor," storing thermal energy when the radiator is unable to reject the required heat load. The stored energy is then removed from the PCM heat exchanger when the environment is more benign. Because they do not use an expendable resource, such as the feed water used by sublimators and evaporators, PCM Heat Exchangers are ideal for long duration Low Lunar Orbit missions. The Advanced Thermal Control project at JSC is completing a PCM heat exchanger life test to determine whether further technology development is warranted. The life test is being conducted on four nPentadecane, carbon filament heat exchangers. Fluid loop performance, repeatability, and measurement of performance degradation over 2500 melt-freeze cycles will be performed and reported in the current document.

Hierarchically Self-Assembled Block Copolymer Blends for Templating Hollow Phase-Change Nanostructures with an Extremely Low Switching Current

DOE PAGES

Park, Woon Ik; Kim, Jong Min; Jeong, Jae Won; ...

2015-03-17

Phase change memory (PCM) is one of the most promising candidates for next-generation nonvolatile memory devices because of its high speed, excellent reliability, and outstanding scalability. But, the high switching current of PCM devices has been a critical hurdle to realize low-power operation. Although one solution is to reduce the switching volume of the memory, the resolution limit of photolithography hinders further miniaturization of device dimensions. Here, we employed unconventional self-assembly geometries obtained from blends of block copolymers (BCPs) to form ring-shaped hollow PCM nanostructures with an ultrasmall contact area between a phase-change material (Ge 2Sb 2Te 5) and amore » heater (TiN) electrode. The high-density (approximately 0.1 terabits per square inch) PCM nanoring arrays showed extremely small switching current of 2-3 mu A. Furthermore, the relatively small reset current of the ring-shaped PCM compared to the pillar-shaped devices is attributed to smaller switching volume, which is well supported by electro-thermal simulation results. Our approach may also be extended to other nonvolatile memory device applications such as resistive switching memory and magnetic storage devices, where the control of nanoscale geometry can significantly affect device performances.« less

High-Pressure Oxygen Generation for Outpost EVA

NASA Technical Reports Server (NTRS)

Jeng, Frank; Conger, Bruce; Anderson, Molly

2008-01-01

Low Lunar Orbit (LLO) poses unique thermal challenges for the orbiting space craft, particularly regarding the performance of the radiators. The emitted infrared (IR) heat flux from the lunar surface varies drastically from the light side to the dark side of the moon. Due to the extremely high incident IR flux, especially at low beta angles, a radiator is oftentimes unable to reject the vehicle heat load throughout the entire lunar orbit. One solution to this problem is to implement Phase Change Material (PCM) Heat Exchangers. PCM Heat Exchangers act as a "thermal capacitor, storing thermal energy when the radiator is unable to reject the required heat load. The stored energy is then removed from the PCM heat exchanger when the environment is more benign. Because they do not use an expendable resource, such as the feed water used by sublimators and evaporators, PCM Heat Exchangers are ideal for long duration Low Lunar Orbit missions. The Advanced Thermal Control project at JSC is completing a PCM heat exchanger life test to determine whether further technology development is warranted. The life test is being conducted on four nPentadecane, carbon filament heat exchangers. Fluid loop performance, repeatability, and measurement of performance degradation over 2500 meltfreeze cycles will be performed and reported in the current document.

Telemetry Standards, RCC Standard 106-17. Chapter 8. Digital Data Bus Acquisition Formatting Standard

DTIC Science & Technology

2017-07-01

8-3 8.4.1 Characteristics of a Singular Composite Output Signal ...................................... 8-3 8.5 Single Bus Track Spread Recording ...Format .............................................................. 8-5 8.5.1 Single Bus Recording Technique Characteristics...check FCS frame check sequence HDDR high-density digital recording MIL-STD Military Standard msb most significant bit PCM pulse code modulation

Internet Protocol Over Telemetry Testing for Earth Science Capability Demo Summary

NASA Technical Reports Server (NTRS)

Franz, Russ; Pestana, Mark; Bessent, Shedrick; Hang, Richard; Ng, Howard

2006-01-01

The development and flight tests described here focused on utilizing existing pulse code modulation (PCM) telemetry equipment to enable on-vehicle networks of instruments and computers to be a simple extension of the ground station network. This capability is envisioned as a necessary component of a global range that supports test and development of manned and unmanned airborne vehicles.

Real time computer data system for the 40 x 80 ft wind tunnel facility at Ames Research Center

NASA Technical Reports Server (NTRS)

Cambra, J. M.; Tolari, G. P.

1974-01-01

The wind tunnel realtime computer system is a distributed data gathering system that features a master computer subsystem, a high speed data gathering subsystem, a quick look dynamic analysis and vibration control subsystem, an analog recording back-up subsystem, a pulse code modulation (PCM) on-board subsystem, a communications subsystem, and a transducer excitation and calibration subsystem. The subsystems are married to the master computer through an executive software system and standard hardware and FORTRAN software interfaces. The executive software system has four basic software routines. These are the playback, setup, record, and monitor routines. The standard hardware interfaces along with the software interfaces provide the system with the capability of adapting to new environments.

Thermal Vacuum Test of Ice as a Phase Change Material Integrated with a Radiator

NASA Technical Reports Server (NTRS)

Lee, Steve; Le, Hung; Leimkuehler, Thomas O.; Stephan, Ryan A.

2009-01-01

Water may be used as radiation shielding for Solar Particle Events (SPE) to protect crewmembers in the Lunar Electric Rover (LER). Because the water is already present for radiation protection, it could also provide a mass efficient solution to the vehicle's thermal control system. This water can be frozen by heat rejection from a radiator and used as a Phase Change Material (PCM) for thermal storage. Use of this water as a PCM can eliminate the need for a pumped fluid loop thermal control system as well as reduce the required size of the radiator. This paper describes the testing and analysis performed for the Rover Engineering Development Unit (REDU), a scaled-down version of a water PCM heat sink for the LER. The REDU was tested in a thermal-vacuum chamber at environmental temperatures similar to those of a horizontal radiator panel on the lunar surface. Testing included complete freeze and melt cycles along with scaled transient heat load profiles simulating a 24-hour day for the rover.

Conditioned medium from Bifidobacteria infantis protects against Cronobacter sakazakii-induced intestinal inflammation in newborn mice

PubMed Central

Weng, Meiqian; Ganguli, Kriston; Zhu, Weishu; Shi, Hai Ning

2014-01-01

Necrotizing enterocolitis (NEC) is associated with a high morbidity and mortality in very low birth weight infants. Several hypotheses regarding the pathogenesis of NEC have been proposed but to date no effective treatment is available. Previous studies suggest that probiotic supplementation is protective. We recently reported that probiotic (Bifidobacterium infantis) conditioned medium (PCM) has an anti-inflammatory effect in cultured fetal human intestinal cells (H4) and fetal intestine explants. In this study, we tested in vivo whether PCM protects neonatal mice from developing intestinal inflammation induced by exposure to Cronobacter sakazakii (C. sakazakii), an opportunistic pathogen associated with NEC. We found that infected neonatal mice had a significantly lower body weight than control groups. Infection led to ileal tissue damage including villous rupture, disruption of epithelial cell alignment, intestinal inflammation, apoptotic cell loss, and decreased mucus production. Pretreatment with PCM prevented infection caused decrease in body weight, attenuated enterocyte apoptotic cell death, mitigated reduced mucin production, and maintained ileal structure. Infected ileum expressed reduced levels of IκBα, which could be restored upon pretreatment with PCM. We also observed a nuclear translocation of NF-κB p65 in H4 cells exposed to C. sakazakii, which was prevented in PCM-pretreated cells. Finally, treatment of neonatal mice with PCM prior to infection sustained the capacity of ileal epithelial proliferation. This study suggests that an active component(s) released into the culture medium by B. infantis may prevent ileal damage by a pathogen linked to NEC. PMID:24627567

Effect of ArtinM on Human Blood Cells During Infection With Paracoccidioides brasiliensis.

PubMed

Ruas, Luciana P; Genaro, Livia M; Justo-Junior, Amauri S; Coser, Lilian O; de Castro, Lívia F; Trabasso, Plinio; Mamoni, Ronei L; Roque-Barreira, Maria-Cristina; Blotta, Maria-Heloisa S L

2018-01-01

Infections caused by fungi are prominent in our environment and can be potentially fatal. paracoccidioidomycosis (PCM), caused by fungi of the Paracoccidioides genus, is the most frequent systemic mycosis in Brazil and the main cause of death among immunocompetent individuals. The antifungal therapy for PCM is usually effective but side effects and relapses are often reported. The latter could be avoided with alternative or complementary therapies aimed at boosting the immune response to combat this pathogen. Recent reports have pointed at the importance of an effective cellular immune response, with the participation of Th1 cells, in the resistance to and control of Paracoccidioides infection. The ArtinM lectin, extracted from jackfruit ( Artocarpus heterophyllus ) seeds, exhibits immunomodulatory activity against several intracellular pathogens, including Paracoccidioides brasiliensis , by promoting the development of a Th1 immune response. The aim of this work was to characterize the effect of ArtinM on peripheral blood cells of patients with PCM and on those of control individuals infected with fungal yeasts cells in vitro . Our results demonstrate that ArtinM activates human neutrophils in vitro , leading to an increase in cytokine production and CD54 expression. ArtinM activated P. brasiliensis -infected neutrophils from both healthy individuals and patients with PCM. This activation was not dependent on the dectin-1 receptor, because pre-incubation with laminarin, a dectin-1 receptor blocker, did not reverse the activated state of the cells. ArtinM also stimulated human peripheral blood mononuclear cells to secrete pro-inflammatory Th1-related cytokines, which are protective against Paracoccidioides infection. These data support the immunostimulatory action of ArtinM and encourage new studies using the lectin for the immunotherapy of PCM.

Effect of ArtinM on Human Blood Cells During Infection With Paracoccidioides brasiliensis

PubMed Central

Ruas, Luciana P.; Genaro, Livia M.; Justo-Junior, Amauri S.; Coser, Lilian O.; de Castro, Lívia F.; Trabasso, Plinio; Mamoni, Ronei L.; Roque-Barreira, Maria-Cristina; Blotta, Maria-Heloisa S. L.

2018-01-01

Infections caused by fungi are prominent in our environment and can be potentially fatal. paracoccidioidomycosis (PCM), caused by fungi of the Paracoccidioides genus, is the most frequent systemic mycosis in Brazil and the main cause of death among immunocompetent individuals. The antifungal therapy for PCM is usually effective but side effects and relapses are often reported. The latter could be avoided with alternative or complementary therapies aimed at boosting the immune response to combat this pathogen. Recent reports have pointed at the importance of an effective cellular immune response, with the participation of Th1 cells, in the resistance to and control of Paracoccidioides infection. The ArtinM lectin, extracted from jackfruit (Artocarpus heterophyllus) seeds, exhibits immunomodulatory activity against several intracellular pathogens, including Paracoccidioides brasiliensis, by promoting the development of a Th1 immune response. The aim of this work was to characterize the effect of ArtinM on peripheral blood cells of patients with PCM and on those of control individuals infected with fungal yeasts cells in vitro. Our results demonstrate that ArtinM activates human neutrophils in vitro, leading to an increase in cytokine production and CD54 expression. ArtinM activated P. brasiliensis-infected neutrophils from both healthy individuals and patients with PCM. This activation was not dependent on the dectin-1 receptor, because pre-incubation with laminarin, a dectin-1 receptor blocker, did not reverse the activated state of the cells. ArtinM also stimulated human peripheral blood mononuclear cells to secrete pro-inflammatory Th1-related cytokines, which are protective against Paracoccidioides infection. These data support the immunostimulatory action of ArtinM and encourage new studies using the lectin for the immunotherapy of PCM. PMID:29780375

Empirical equations for viscosity and specific heat capacity determination of paraffin PCM and fatty acid PCM

NASA Astrophysics Data System (ADS)

Barreneche, C.; Ferrer, G.; Palacios, A.; Solé, A.; Inés Fernández, A.; Cabeza, L. F.

2017-10-01

Phase change materials (PCM) used in thermal energy storage (TES) systems have been presented, over recent years, as one of the most effective options in energy storage. Paraffin and fatty acids are some of the most used PCM in TES systems, as they have high phase change enthalpy and in addition they do not present subcooling nor hysteresis and have proper cycling stability. The simulations and design of TES systems require the knowledge of the thermophysical properties of PCM. Thermal conductivity, viscosity, specific heat capacity (Cp) can be experimentally determined, but these are material and time consuming tasks. To avoid or to reduce them, and to have reliable data without the need of experimentation, thermal properties can be calculated by empirical equations. In this study, five different equations are given to calculate the viscosity and specific heat capacity of fatty acid PCM and paraffin PCM. Two of these equations concern, respectively, the empirical calculation of the viscosity and liquid Cp of the whole paraffin PCM family, while the other three equations presented are for the corresponding calculation of viscosity, solid Cp, liquid Cp of the whole fatty acid family of PCM. Therefore, this study summarize the work performed to obtain the main empirical equations to measure the above mentioned properties for whole fatty acid PCM family and whole paraffin PCM family. Moreover, empirical equations have been obtained to calculate these properties for other materials of these PCM groups and these empirical equations can be extrapolated for PCM with higher or lower phase change temperatures within a lower relative error 4%.

An architecture for object-oriented intelligent control of power systems in space

NASA Technical Reports Server (NTRS)

Holmquist, Sven G.; Jayaram, Prakash; Jansen, Ben H.

1993-01-01

A control system for autonomous distribution and control of electrical power during space missions is being developed. This system should free the astronauts from localizing faults and reconfiguring loads if problems with the power distribution and generation components occur. The control system uses an object-oriented simulation model of the power system and first principle knowledge to detect, identify, and isolate faults. Each power system component is represented as a separate object with knowledge of its normal behavior. The reasoning process takes place at three different levels of abstraction: the Physical Component Model (PCM) level, the Electrical Equivalent Model (EEM) level, and the Functional System Model (FSM) level, with the PCM the lowest level of abstraction and the FSM the highest. At the EEM level the power system components are reasoned about as their electrical equivalents, e.g, a resistive load is thought of as a resistor. However, at the PCM level detailed knowledge about the component's specific characteristics is taken into account. The FSM level models the system at the subsystem level, a level appropriate for reconfiguration and scheduling. The control system operates in two modes, a reactive and a proactive mode, simultaneously. In the reactive mode the control system receives measurement data from the power system and compares these values with values determined through simulation to detect the existence of a fault. The nature of the fault is then identified through a model-based reasoning process using mainly the EEM. Compound component models are constructed at the EEM level and used in the fault identification process. In the proactive mode the reasoning takes place at the PCM level. Individual components determine their future health status using a physical model and measured historical data. In case changes in the health status seem imminent the component warns the control system about its impending failure. The fault isolation process uses the FSM level for its reasoning base.

Thermal characterization of full-scale PCM products and numerical simulations, including hysteresis, to evaluate energy impacts in an envelope application

DOE PAGES

Biswas, Kaushik; Shukla, Yash; Desjarlais, Andre Omer; ...

2018-04-17

This article presents combined measurements of fatty acid-based organic PCM products and numerical simulations to evaluate the energy benefits of adding a PCM layer to an exterior wall. The thermal storage characteristics of the PCM were measured using a heat flow meter apparatus (HFMA). The PCM characterization is based on a recent ASTM International standard test method, ASTM C1784. The PCM samples were subjected to step changes in temperature and allowed to stabilize at each temperature. By measuring the heat absorbed or released by the PCM, the temperature-dependent enthalpy functions for melting and freezing were determined.Here, the simulations were donemore » using a previously-validated two-dimensional (2D) wall model containing a PCM layer and incorporating the HFMA-measured enthalpy functions. The wall model was modified to include the hysteresis phenomenon observed in PCMs, which is reflected in different melting and freezing temperatures of the PCM. Simulations were done with a single enthalpy curve based on the PCM melting tests, both melting and freezing enthalpy curves, and with different degrees of hysteresis between the melting and freezing curves. Significant differences were observed between the thermal performances of the modeled wall with the PCM layer under the different scenarios.« less

Thermal characterization of full-scale PCM products and numerical simulations, including hysteresis, to evaluate energy impacts in an envelope application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Shukla, Yash; Desjarlais, Andre Omer

This article presents combined measurements of fatty acid-based organic PCM products and numerical simulations to evaluate the energy benefits of adding a PCM layer to an exterior wall. The thermal storage characteristics of the PCM were measured using a heat flow meter apparatus (HFMA). The PCM characterization is based on a recent ASTM International standard test method, ASTM C1784. The PCM samples were subjected to step changes in temperature and allowed to stabilize at each temperature. By measuring the heat absorbed or released by the PCM, the temperature-dependent enthalpy functions for melting and freezing were determined.Here, the simulations were donemore » using a previously-validated two-dimensional (2D) wall model containing a PCM layer and incorporating the HFMA-measured enthalpy functions. The wall model was modified to include the hysteresis phenomenon observed in PCMs, which is reflected in different melting and freezing temperatures of the PCM. Simulations were done with a single enthalpy curve based on the PCM melting tests, both melting and freezing enthalpy curves, and with different degrees of hysteresis between the melting and freezing curves. Significant differences were observed between the thermal performances of the modeled wall with the PCM layer under the different scenarios.« less

Experimental performances of a battery thermal management system using a phase change material

NASA Astrophysics Data System (ADS)

Hémery, Charles-Victor; Pra, Franck; Robin, Jean-François; Marty, Philippe

2014-12-01

Li-ion batteries are leading candidates for mobility because electric vehicles (EV) are an environmentally friendly mean of transport. With age, Li-ion cells show a more resistive behavior leading to extra heat generation. Another kind of problem called thermal runway arises when the cell is too hot, what happens in case of overcharge or short circuit. In order to evaluate the effect of these defects at the whole battery scale, an air-cooled battery module was built and tested, using electrical heaters instead of real cells for safety reasons. A battery thermal management system based on a phase change material is developed in that study. This passive system is coupled with an active liquid cooling system in order to initialize the battery temperature at the melting of the PCM. This initialization, or PCM solidification, can be performed during a charge for example, in other words when the energy from the network is available.

Experimental investigation of thermal characteristics of lithium ion battery using phase change materials combined with metallic foams and fins

NASA Astrophysics Data System (ADS)

Deng, Y. C.; Zhang, H. Y.; Xia, X.

2016-08-01

Phase change materials are of great interest in energy storage and energy management applications due to their high latent heat and excellent cycling stability. In this paper, the thermal characteristics of phase change materials (PCM) for thermal management of cylindrical 18650 lithium-ion battery (LIB) were experimentally investigated. A commercial paraffin wax with a melting temperaturerange between 47 - 53.8oC was used in this study. A metal cylinder with a heater was used to emulate the heat generation from a battery, which was surrounded with the paraffin PCM and containted in a metal housing. The experiment was conducted in an environmental test chamber with controlled ambient temperatures and power inputs. Both the battery temperature and the housing wall temperature were measured during steady-state heating and cyclic heating conditions. Since PCM has low thermal conductivity, thermal enhancement techniques were investigated by adding metal foams (MFs) or combining metallic foam and fins into the PCM to enhance the thermal conductivity. The battery temperatures were measured for all the cases and the results were analyzed and discussed.

A mathematical model of embodied consciousness.

PubMed

Rudrauf, David; Bennequin, Daniel; Granic, Isabela; Landini, Gregory; Friston, Karl; Williford, Kenneth

2017-09-07

We introduce a mathematical model of embodied consciousness, the Projective Consciousness Model (PCM), which is based on the hypothesis that the spatial field of consciousness (FoC) is structured by a projective geometry and under the control of a process of active inference. The FoC in the PCM combines multisensory evidence with prior beliefs in memory and frames them by selecting points of view and perspectives according to preferences. The choice of projective frames governs how expectations are transformed by consciousness. Violations of expectation are encoded as free energy. Free energy minimization drives perspective taking, and controls the switch between perception, imagination and action. In the PCM, consciousness functions as an algorithm for the maximization of resilience, using projective perspective taking and imagination in order to escape local minima of free energy. The PCM can account for a variety of psychological phenomena: the characteristic spatial phenomenology of subjective experience, the distinctions and integral relationships between perception, imagination and action, the role of affective processes in intentionality, but also perceptual phenomena such as the dynamics of bistable figures and body swap illusions in virtual reality. It relates phenomenology to function, showing the computational advantages of consciousness. It suggests that changes of brain states from unconscious to conscious reflect the action of projective transformations and suggests specific neurophenomenological hypotheses about the brain, guidelines for designing artificial systems, and formal principles for psychology. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Diagnostic Approach for Rodent Progressive Cardiomyopathy and Like Lesions in Toxicology Studies up to 28 Days in the Sprague Dawley Rat (Part 1 of 2).

PubMed

Hailey, James R; Maleeff, Beverly E; Thomas, Heath C; Pearse, Gail; Klapwijk, Jan C; Cristofori, Patrizia G; Berridge, Brian; Kimbrough, Carie L; Parker, George A; Morton, Daniel; Elmore, Susan; Hardisty, Jerry F; Dybdal, Noel O; Rehagen, David A; Fikes, James D; Lamb, Martin; Biddle, Kathleen; Buetow, Bernard S; Carreira, Vinicius; Nyska, Abraham; Tripathi, Niraj K; Workman, Heather C; Bienvenu, Jean-Guy; Brees, Ingrid; Turk, James R; Adler, Rick R

2017-12-01

Spontaneous rodent progressive cardiomyopathy (PCM) in the Sprague Dawley rat may confound identification and/or interpretation of potential test article (TA)-related cardiotoxicity. Pathologists apply diagnostic term(s) and thresholds for diagnosing and assigning severity grades for PCM and/or PCM-like (PCM/like) lesions consistently within a study, which is necessary to identify and interpret TA-related findings. Due to differences in training and/or experiences, diagnostic terms and thresholds may vary between pathologists. Harmonized terminology and thresholds across studies will generate better historical control data, will likely enhance interpretation of study data, and may further enhance our understanding of the spontaneous change. An assessment of the diagnostic approaches of a group of 37 pathologists identified an approach that is relatively easily applied; and if adopted, it could enhance diagnostic consistency across studies. This approach uses the single "slash" term "necrosis/inflammatory cell infiltrate (NICI)" as the diagnosis for the spectrum of lesions seen in younger rats, uses no threshold for diagnosis (e.g., diagnose all lesions clearly identifiable as PCM/like), and uses aggregate lesion size of approximately ≥45% of the field of view (FOV) using a 10×/22 eyepiece and the 40× objective or approximately ≥100% of the FOV using the 60× objective as the criterion separating minimal from mild severities.

Anti-Idiotypic Antibodies in Patients with Different Clinical Forms of Paracoccidioidomycosis

PubMed Central

Souza, A. R.; Gesztesi, J.-L.; del Negro, G. M. B.; Benard, G.; Sato, J.; Santos, M. V. B.; Abrahão, T. B.; Lopes, J. D.

2000-01-01

Paracoccidioidomycosis (PCM) is the most prevalent systemic mycosis in Latin America. Patients with PCM show a wide spectrum of clinical and pathological manifestations depending on both host and pathogen factors. Two clinical forms of the disease are recognized: the acute or juvenile form and the chronic or adult form. The major antigenic component of the parasite is a glycoprotein of 43 kDa (gp43). All patient sera present antibodies against gp43 (anti-gp43) and, as demonstrated before by our group, spontaneous anti-idiotypic (anti-Id) antibodies (Ab2) can be detected in patient sera with high titers of anti-gp43. Since it has been postulated that anti-Id antibodies may have a modulating function, we decided to purify and characterize anti-Id antibodies in this system. The possible correlation of Ab2 titers with different clinical forms of disease was also verified. Results showed that purified human anti-Id antibodies (human Ab2) recognized specifically the idiotype of some murine monoclonal anti-gp43 (17c and 3e) but not others (40.d7, 27a, and 8a). Spontaneous anti-Id antibodies were found in all clinical forms of disease. The majority of patients (88%, n = 8) with the acute form of PCM had high titers of Ab2. However, among patients with the multifocal chronic form of the disease, only 29% (n = 14) had high titers of Ab2; 70% (n = 10) of patients with the unifocal chronic form had low titers of Ab2. A correlation between Ab2 titers and anti-gp43 titers was observed before and during antimycotic treatment. Our results suggest that titers of anti-Id antibodies correlate with the severity of PCM in humans. PMID:10702489

Validation Methodology to Allow Simulated Peak Reduction and Energy Performance Analysis of Residential Building Envelope with Phase Change Materials: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tabares-Velasco, P. C.; Christensen, C.; Bianchi, M.

2012-08-01

Phase change materials (PCM) represent a potential technology to reduce peak loads and HVAC energy consumption in residential buildings. This paper summarizes NREL efforts to obtain accurate energy simulations when PCMs are modeled in residential buildings: the overall methodology to verify and validate Conduction Finite Difference (CondFD) and PCM algorithms in EnergyPlus is presented in this study. It also shows preliminary results of three residential building enclosure technologies containing PCM: PCM-enhanced insulation, PCM impregnated drywall and thin PCM layers. The results are compared based on predicted peak reduction and energy savings using two algorithms in EnergyPlus: the PCM and Conductionmore » Finite Difference (CondFD) algorithms.« less

Evaluation of in situ expression of effector and regulatory cytokines, TLR, galectins and matrix metalloproteinases in oral manifestations of paracoccidioidomycosis.

PubMed

de Araújo, Marcelo Sivieri; Alves, Polyanna Miranda; de Lima, Lilian Margareth Biagioni; da Silva, Marcelo Fernandes; de Lima Pereira, Sanívia Aparecida; Rodrigues, Virmondes; Rodrigues, Denise Bertulucci Rocha

2015-01-01

Although the pathophysiology of paracoccidioidomycosis (PCM) is not completely understood, the study of immune response against fungus has provided insight into understanding the natural course of the disease and its clinical manifestations, hence contributing to the development of preventive measures and treatment proposals. The aim of this study was to evaluate the histopathological and immunological aspects involved in the role of different effector and regulatory responses, as well as the correlation between the TLRs, Galectins, Matrix Metalloproteinases and cytoplasmic proteases of mast cells in this infection. Sixteen biopsy specimens with oral lesions of chronic PCM, as well as 13 sections of normal oral mucosa were analyzed. Histopathological and immunological aspects involved in the role of different effector and regulatory responses were evaluated. Indirect immunohistochemistry was performed for IL-17, IL-10, IL-4, TGF-β, FoxP3, Gal-1, Gal-3, Gal-9, TLR-2, TLR-4, MMP-3 and MMP-9, as well as for chymase and tryptase for mast cells identification. Fibrosis was quantified using Picrosirius. There was a significant increase in the area of fibrosis and in the number of cells expressing IL-10, IL-4, IL-17, FoxP3, Gal-3, TLR-2, MMP3 and MMP9 in patients with PCM in comparison with patients in the group control. There was no difference in the expression of TGF-β, TLR-4, Gal-1 or Gal-9. Mast cells number was found to be significantly lower in oral chronic PCM when compared to control samples after quantification of mast cells and expression of chymase and tryptase. PCM granulomas were classified to the morphological aspects in organized ou non-organized. Expression of IL-4 in non-organized granulomas was significantly higher. The proteins studied herein appear to play an important role in the development and maintenance of oral lesions of PCM, as well as in the processes of development and progression of lesions caused by the fungus and by the immune response associated with the infection. Copyright © 2014 Elsevier GmbH. All rights reserved.

Study of Fresh and Hardening Process Properties of Gypsum with Three Different PCM Inclusion Methods

PubMed Central

Serrano, Susana; Barreneche, Camila; Navarro, Antonia; Haurie, Laia; Fernandez, A. Inés; Cabeza, Luisa F.

2015-01-01

Gypsum has two important states (fresh and hardened states), and the addition of phase change materials (PCM) can vary the properties of the material. Many authors have extensively studied properties in the hardened state; however, the variation of fresh state properties due to the addition of Micronal® DS 5001 X PCM into gypsum has been the object of few investigations. Properties in fresh state define the workability, setting time, adherence and shrinkage, and, therefore the possibility of implementing the material in building walls. The aim of the study is to analyze, compare and evaluate the variability of fresh state properties after the inclusion of 10% PCM. PCM are added into a common gypsum matrix by three different methods: adding microencapsulated PCM, making a suspension of PCM/water, and incorporating PCM through a vacuum impregnation method. Results demonstrate that the inclusion of PCM change completely the water required by the gypsum to achieve good workability, especially the formulation containing Micronal® DS 5001 X: the water required is higher, the retraction is lower (50% less) due to the organic nature of the PCM with high elasticity and, the adherence is reduced (up to 45%) due to the difference between the porosity of the different surfaces as well as the surface tension difference. PMID:28793584

T Helper 1–Inducing Adjuvant Protects against Experimental Paracoccidioidomycosis

PubMed Central

de Oliveira, Leandro Licursi; Coltri, Kely Cristine; Cardoso, Cristina Ribeiro Barros; Roque-Barreira, Maria-Cristina; Panunto-Castelo, Ademilson

2008-01-01

Immunostimulatory therapy is a promising approach to improving the treatment of systemic fungal infections such as paracoccidioidomycosis (PCM), whose drug therapy is usually prolonged and associated with toxic side effects and relapses. The current study was undertaken to determine if the injection of a T helper (Th) 1–stimulating adjuvant in P. brasiliensis–infected mice could have a beneficial effect on the course of experimental PCM. For this purpose, mice were infected and treated with complete Freund's adjuvant (CFA), a well-established Th1 experimental inductor, or incomplete Freund's adjuvant (IFA - control group) on day 20 postinfection. Four weeks after treatment, the CFA-treated mice presented a mild infection in the lungs characterized by absence of epithelioid cell granulomas and yeast cells, whereas the control mice presented multiple sites of focal epithelioid granulomas with lymphomonocytic halos circumscribing a high number of viable and nonviable yeast cells. In addition, CFA administration induced a 2.4 log reduction (>99%) in the fungal burden when compared to the control group, and led to an improvement of immune response, reversing the immunosuppression observed in the control group. The immunotherapy with Th1-inducing adjuvant, approved to be used in humans, might be a valuable tool in the treatment of PCM and potentially useful to improve the clinical cure rate in humans. PMID:18335066

Temperature control transport system

DOEpatents

Schabron, John F; Sorini-Wong, Susan S

2014-12-09

Embodiments of the inventive technology may involve the use of layered, insulated PCM assemblage that itself comprises: modular insulating foam material 8 that, upon establishment as part of the assemblage, defines inner foam material sides 9 and outer foam material sides 10; thin reflective material 11 established against (whether directly in contact with or not) at least either the inner foam material sides or the outer foam materials sides, and modular, enclosed PCM sections 12 established between the modular insulating foam material and the interior center.

Genetic algorithm based active vibration control for a moving flexible smart beam driven by a pneumatic rod cylinder

NASA Astrophysics Data System (ADS)

Qiu, Zhi-cheng; Shi, Ming-li; Wang, Bin; Xie, Zhuo-wei

2012-05-01

A rod cylinder based pneumatic driving scheme is proposed to suppress the vibration of a flexible smart beam. Pulse code modulation (PCM) method is employed to control the motion of the cylinder's piston rod for simultaneous positioning and vibration suppression. Firstly, the system dynamics model is derived using Hamilton principle. Its standard state-space representation is obtained for characteristic analysis, controller design, and simulation. Secondly, a genetic algorithm (GA) is applied to optimize and tune the control gain parameters adaptively based on the specific performance index. Numerical simulations are performed on the pneumatic driving elastic beam system, using the established model and controller with tuned gains by GA optimization process. Finally, an experimental setup for the flexible beam driven by a pneumatic rod cylinder is constructed. Experiments for suppressing vibrations of the flexible beam are conducted. Theoretical analysis, numerical simulation and experimental results demonstrate that the proposed pneumatic drive scheme and the adopted control algorithms are feasible. The large amplitude vibration of the first bending mode can be suppressed effectively.

Numerical analysis of fluid flow and heat transfer during melting inside a cylindrical container for thermal energy storage system

NASA Astrophysics Data System (ADS)

Bellan, Selvan; Cheok, Cho Hyun; Gokon, Nobuyuki; Matsubara, Koji; Kodama, Tatsuya

2017-06-01

This paper presents a numerical analysis of unconstrained melting of high temperature(>1000K) phase change material (PCM) inside a cylindrical container. Sodium chloride and Silicon carbide have been used as phase change material and shell of the capsule respectively. The control volume discretization approach has been used to solve the conservation equations of mass, momentum and energy. The enthalpy-porosity method has been used to track the solid-liquid interface of the PCM during melting process. Transient numerical simulations have been performed in order to study the influence of radius of the capsule and the Stefan number on the heat transfer rate. The simulation results show that the counter-clockwise Buoyancy driven convection over the top part of the solid PCM enhances the melting rate quite faster than the bottom part.

Thermal buffering performance of composite phase change materials applied in low-temperature protective garments

NASA Astrophysics Data System (ADS)

Yang, Kai; Jiao, Mingli; Yu, Yuanyuan; Zhu, Xueying; Liu, Rangtong; Cao, Jian

2017-07-01

Phase change material (PCM) is increasingly being applied in the manufacturing of functional thermo-regulated textiles and garments. This paper investigated the thermal buffering performance of different composite PCMs which are suitable for the application in functional low-temperature protective garments. First, according to the criteria selecting PCM for functional textiles/garments, three kinds of pure PCM were selected as samples, which were n-hexadecane, n-octadecane and n-eicosane. To get the adjustable phase change temperature range and higher phase change enthalpy, three kinds of composite PCM were prepared using the above pure PCM. To evaluate the thermal buffering performance of different composite PCM samples, the simulated low-temperature experiments were performed in the climate chamber, and the skin temperature variation curves in three different low temperature conditions were obtained. Finally composite PCM samples’ thermal buffering time, thermal buffering capacity and thermal buffering efficiency were calculated. Results show that the comprehensive thermal buffering performance of n-octadecane and n-eicosane composite PCM is the best.

A molecular mechanism of mitotic centrosome assembly in Drosophila

PubMed Central

Conduit, Paul T; Richens, Jennifer H; Wainman, Alan; Holder, James; Vicente, Catarina C; Pratt, Metta B; Dix, Carly I; Novak, Zsofia A; Dobbie, Ian M; Schermelleh, Lothar; Raff, Jordan W

2014-01-01

Centrosomes comprise a pair of centrioles surrounded by pericentriolar material (PCM). The PCM expands dramatically as cells enter mitosis, but it is unclear how this occurs. In this study, we show that the centriole protein Asl initiates the recruitment of DSpd-2 and Cnn to mother centrioles; both proteins then assemble into co-dependent scaffold-like structures that spread outwards from the mother centriole and recruit most, if not all, other PCM components. In the absence of either DSpd-2 or Cnn, mitotic PCM assembly is diminished; in the absence of both proteins, it appears to be abolished. We show that DSpd-2 helps incorporate Cnn into the PCM and that Cnn then helps maintain DSpd-2 within the PCM, creating a positive feedback loop that promotes robust PCM expansion around the mother centriole during mitosis. These observations suggest a surprisingly simple mechanism of mitotic PCM assembly in flies. DOI: http://dx.doi.org/10.7554/eLife.03399.001 PMID:25149451

Serum interleukin-18 and soluble tumour necrosis factor receptor 2 are associated with disease severity in patients with paracoccidioidomycosis

PubMed Central

Corvino, C L; Mamoni, R L; Fagundes, G Z Z; Blotta, M H S L

2007-01-01

Interleukin (IL)-18 is a proinflammatory cytokine of the IL-1 superfamily that exhibits broad functional effects in innate and acquired immune responses and which has been found in high levels in several chronic inflammatory and autoimmune diseases. Over-expression of IL-18 may promote early resolution of infection or could promote a detrimental exaggerated immune response. The aim of this study was to determine serum levels of IL-18 and other inflammatory mediators [IL-12, soluble intercellular adhesion molecule 1 (sICAM-1), soluble tumour necrosis factor receptor 1 (TNF-RI), sTNF-RII, CXC chemokine ligand 9 (CXCL9), CXCL10] at baseline and after anti-fungal therapy in serum from patients with juvenile (JF) and adult (AF) forms of paracoccidioidomycosis (PCM), as well as in healthy controls (C), and to assess their possible relationships to the severity of disease. IL-18 and sTNF-RII levels in patients with the JF of PCM were significantly higher than those in the AF and controls. In relation to sICAM-1, no difference was observed between JF and AF patients but both presented higher levels than controls. sTNF-RI levels were higher in patients with PCM than in controls, and significantly higher concentrations were detected in AF patients compared to JF patients. Moreover, IL-12 and chemokines CXCL9 and CXCL10 were also higher in patients than in controls. In JF patients IL-18 levels correlated significantly with sICAM-1 (r = 0·62, P < 0·0001), sTNF-RI (r = 0·63, P < 0·0001), sTNF-RII (r = 0·51, P = 0·02), as well as with clinical severity. The results suggest the value of serum IL-18 and sTNF-Rs levels as a parameter of PCM severity and may support a possible role for them in the pathogenesis of the disease. PMID:17302897

Integrity of the Pericentriolar Material Is Essential for Maintaining Centriole Association during M Phase

PubMed Central

Rhee, Kunsoo

2015-01-01

A procentriole is assembled next to the mother centriole during S phase and remains associated until M phase. After functioning as a spindle pole during mitosis, the mother centriole and procentriole are separated at the end of mitosis. A close association of the centriole pair is regarded as an intrinsic block to the centriole reduplication. Therefore, deregulation of this process may cause a problem in the centriole number control, resulting in increased genomic instability. Despite its importance for faithful centriole duplication, the mechanism of centriole separation is not fully understood yet. Here, we report that centriole pairs are prematurely separated in cells whose cell cycle is arrested at M phase by STLC. Dispersal of the pericentriolar material (PCM) was accompanied. This phenomenon was independent of the separase activity but needed the PLK1 activity. Nocodazole effectively inhibited centriole scattering in STLC-treated cells, possibly by reducing the microtubule pulling force around centrosomes. Inhibition of PLK1 also reduced the premature separation of centrioles and the PCM dispersal as well. These results revealed the importance of PCM integrity in centriole association. Therefore, we propose that PCM disassembly is one of the driving forces for centriole separation during mitotic exit. PMID:26407333

HIV Immune Recovery Inflammatory Syndrome and Central Nervous System Paracoccidioidomycosis.

PubMed

de Almeida, Sérgio Monteiro; Roza, Thiago Henrique

2017-04-01

The immune reconstitution inflammatory syndrome (IRIS) is a deregulated inflammatory response to invading microorganisms. It is manifested when there is an abrupt change in host immunity from an anti-inflammatory and immunosuppressive state to a pro-inflammatory state as a result of rapid depletion or removal of factors that promote immune suppression or inhibition of inflammation. The aim of this paper is to discuss and re-interpret the possibility of association of paracoccidioidomycosis (PCM) with IRIS in the central nervous system (CNS) in a case from Brazil published by Silva-Vergara ML. et al. (Mycopathologia 177:137-141, 6). An AIDS patient who was not receiving medical care developed pulmonary PCM successfully treated with itraconazole. The patient developed central nervous system PCM (NPCM) after starting the ARV therapy with recovery of immunity and control of HIV viral load, although it was not interpreted as IRIS by the authors, it fulfills the criteria for CNS IRIS. This could be the first case of NPCM associated with IRIS described. Although not frequent, IRIS must be considered in PCM patients and HIV, from endemic areas or patients that traveled to endemic areas, receiving ARV treatment and with worsening symptoms.

Energy saving opportunities in the refrigerated transport sector through Phase Change Materials (PCMs) application

NASA Astrophysics Data System (ADS)

Principi, P.; Fioretti, R.; Copertaro, B.

2017-11-01

Transportation of food products at controlled temperature is a critical task in the transport sector. In fact, whilst there is a need of ensuring both food quality and safety to the global population, its impact in terms of energy consumption and related CO2 emissions into the atmosphere is becoming increasingly evident. In this regard, Thermal Energy Storage (TES) using Phase Change Materials (PCMs) can be considered as a potential way of reducing the cooling load, energy consumption and related greenhouse gas emissions in refrigerated transport sector. In this paper two different PCM applications are investigated. Specifically, in the first study a PCM (35 °C melting temperature) layer was added to the external side of a refrigerated enclosure wall with the aim of managing the cooling peak (shifting and reducing) and reducing the daily energy rate. Outdoor experimental results showed that the added PCM layer helps to reduce (between 5.55% and 8.57%) and delay (between 4.30 h and 3.30 h) the peak load of incoming heat compared to the reference one. In the second study, the energy performance of a refrigerated chamber with an air heat exchanger containing PCM (5°C melting temperature) was investigated. The study purpose was to reduce the cooling energy consumption during steady state operating conditions and the rate of temperature increase throughout the course of a power failure event. Test results showed that using a PCM air heat exchanger addition, up to 16% of energy can be saved.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1994-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1994-02-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 2 figures.

Development of a system for off-peak electrical energy use by air conditioners and heat pumps

NASA Astrophysics Data System (ADS)

Russell, L. D.

1980-05-01

Investigation and evaluation of several alternatives for load management for the TVA system are described. Specific data for the TVA system load characteristics were studied to determine the typical peak and off peak periods for the system. The alternative systems investigated for load management included gaseous energy storage, phase change materials energy storage, zeolite energy storage, variable speed controllers for compressors, and weather sensitive controllers. After investigating these alternatives, system design criteria were established; then, the gaseous and PCM energy storage systems were analyzed. The system design criteria include economic assessment of all alternatives. Handbook data were developed for economic assessment. A liquid/PCM energy storage system was judged feasible.

Thermal Energy Storage using PCM for Solar Domestic Hot Water Systems: A Review

NASA Astrophysics Data System (ADS)

Khot, S. A.; Sane, N. K.; Gawali, B. S.

2012-06-01

Thermal energy storage using phase chase materials (PCM) has received considerable attention in the past two decades for time dependent energy source such as solar energy. From several experimental and theoretical analyses that have been made to assess the performance of thermal energy storage systems, it has been demonstrated that PCM-based systems are reliable and viable options. This paper covers such information on PCMs and PCM-based systems developed for the application of solar domestic hot water system. In addition, economic analysis of thermal storage system using PCM in comparison with conventional storage system helps to validate its commercial possibility. From the economic analysis, it is found that, PCM based solar domestic hot water system (SWHS) provides 23 % more cumulative and life cycle savings than conventional SWHS and will continue to perform efficiently even after 15 years due to application of non-metallic tank. Payback period of PCM-based system is also less compared to conventional system. In conclusion, PCM based solar water heating systems can meet the requirements of Indian climatic situation in a cost effective and reliable manner.

An investigation of lithium-ion battery thermal management using paraffin/porous-graphite-matrix composite

NASA Astrophysics Data System (ADS)

Greco, Angelo; Jiang, Xi; Cao, Dongpu

2015-03-01

The thermal management of a cylindrical battery cell by a phase change material (PCM)/compressed expanded natural graphite (CENG) is investigated in this study. The transient thermal behaviour of both the battery and the PCM/CENG is described with a simplified one-dimensional model taking into account the physical and phase change properties of the PCM/CENG composite. The 1D analytical/computational model yielded nearly identical results to the three-dimensional simulation results for various cooling strategies. Therefore, the 1D model is sufficient to describe the transient behaviour of the battery cooled by a PCM/CENG composite. Moreover, the maximum temperature reached by the PCM/CENG cooling strategy is much lower than that by the forced convection in the same configuration. In the test case studied, the PCM showed superior transient characteristics to forced convection cooling. The PCM cooling is able to maintain a lower maximum temperature during the melting process and to extend the transient time for temperature rise. Furthermore, the graphite-matrix bulk density is identified as an important parameter for optimising the PCM/CENG cooling strategy.

Phased Array Technology with Phase and Amplitude Controlled Magnetron for Microwave Power Transmission

NASA Astrophysics Data System (ADS)

Shinohara, N.; Matsumoto, H.

2004-12-01

We need a microwave power transmitter with light weight and high DC-RF conversion efficiency for an economical SSPS (Space Solar Power System). We need a several g/W for a microwave power transmission (MPT) system with a phased array with 0.0001 degree of beam control accuracy (=tan-1 (100m/36,000km)) and over 80 % of DC-RF conversion efficiency when the weight of the 1GW-class SPS is below a several thousand ton - a several tens of thousand ton. We focus a microwave tube, especially magnetron by economical reason and by the amount of mass-production because it is commonly used for microwave oven in the world. At first, we have developed a phase controlled magnetron (PCM) with different technologies from what Dr. Brown developed. Next we have developed a phase and amplitude controlled magnetron (PACM). For the PACM, we add a feedback to magnetic field of the PCM with an external coil to control and stabilize amplitude of the microwave. We succeed to develop the PACM with below 10-6 of frequency stability and within 1 degree of an error in phase and within 1% of amplitude. We can control a phase and amplitude of the PACM and we have developed a phased array the PCMs. With the PCM technology, we have developed a small light weight MPT transmitter COMET (Compact Microwave Energy Transmitter) with consideration of heat radiation for space use and with consideration of mobility to space.

Nanofluid based on self-nanoencapsulated metal/metal alloys phase change materials with tuneable crystallisation temperature.

PubMed

Navarrete, Nuria; Gimeno-Furio, Alexandra; Mondragon, Rosa; Hernandez, Leonor; Cabedo, Luis; Cordoncillo, Eloisa; Julia, J Enrique

2017-12-14

Nanofluids using nanoencapsulated Phase Change Materials (nePCM) allow increments in both the thermal conductivity and heat capacity of the base fluid. Incremented heat capacity is produced by the melting enthalpy of the nanoparticles core. In this work two important advances in this nanofluid type are proposed and experimentally tested. It is firstly shown that metal and metal alloy nanoparticles can be used as self-encapsulated nePCM using the metal oxide layer that forms naturally in most commercial synthesis processes as encapsulation. In line with this, Sn/SnOx nanoparticles morphology, size and thermal properties were studied by testing the suitability and performance of encapsulation at high temperatures and thermal cycling using a commercial thermal oil (Therminol 66) as the base fluid. Secondly, a mechanism to control the supercooling effect of this nePCM type based on non-eutectic alloys was developed.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1992-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1993-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1993-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garmets, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1993-10-19

Free flowing, conformable powder-like mix of silica particles and a phase change material (pcm) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 10 figures.

Energy Performance and Optimal Control of Air-conditioned Buildings Integrated with Phase Change Materials

NASA Astrophysics Data System (ADS)

Zhu, Na

This thesis presents an overview of the previous research work on dynamic characteristics and energy performance of buildings due to the integration of PCMs. The research work on dynamic characteristics and energy performance of buildings using PCMs both with and without air-conditioning is reviewed. Since the particular interest in using PCMs for free cooling and peak load shifting, specific research efforts on both subjects are reviewed separately. A simplified physical dynamic model of building structures integrated with SSPCM (shaped-stabilized phase change material) is developed and validated in this study. The simplified physical model represents the wall by 3 resistances and 2 capacitances and the PCM layer by 4 resistances and 2 capacitances respectively while the key issue is the parameter identification of the model. This thesis also presents the studies on the thermodynamic characteristics of buildings enhanced by PCM and on the investigation of the impacts of PCM on the building cooling load and peak cooling demand at different climates and seasons as well as the optimal operation and control strategies to reduce the energy consumption and energy cost by reducing the air-conditioning energy consumption and peak load. An office building floor with typical variable air volume (VAV) air-conditioning system is used and simulated as the reference building in the comparison study. The envelopes of the studied building are further enhanced by integrating the PCM layers. The building system is tested in two selected cities of typical climates in China including Hong Kong and Beijing. The cold charge and discharge processes, the operation and control strategies of night ventilation and the air temperature set-point reset strategy for minimizing the energy consumption and electricity cost are studied. This thesis presents the simulation test platform, the test results on the cold storage and discharge processes, the air-conditioning energy consumption and demand reduction potentials in typical air-conditioning seasons in typical China cites as well as the impacts of operation and control strategies.

Combined experimental and numerical evaluation of a prototype nano-PCM enhanced wallboard

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; LuPh.D., Jue; Soroushian, Parviz

2014-01-01

In the United States, forty-eight (48) percent of the residential end-use energy consumption is spent on space heating and air conditioning. Reducing envelope-generated heating and cooling loads through application of phase change material (PCM)-enhanced building envelopes can facilitate maximizing the energy efficiency of buildings. Combined experimental testing and numerical modeling of PCM-enhanced envelope components are two important aspects of the evaluation of their energy benefits. An innovative phase change material (nano-PCM) was developed with PCM encapsulated with expanded graphite (interconnected) nanosheets, which is highly conductive for enhanced thermal storage and energy distribution, and is shape-stable for convenient incorporation into lightweightmore » building components. A wall with cellulose cavity insulation and prototype PCM-enhanced interior wallboards was built and tested in a natural exposure test (NET) facility in a hot-humid climate location. The test wall contained PCM wallboards and regular gypsum wallboard, for a side-by-side annual comparison study. Further, numerical modeling of the walls containing the nano-PCM wallboard was performed to determine its actual impact on wall-generated heating and cooling loads. The model was first validated using experimental data, and then used for annual simulations using Typical Meteorological Year (TMY3) weather data. This article presents the measured performance and numerical analysis evaluating the energy-saving potential of the nano-PCM-enhanced wallboard.« less

PCM-Based Durable Write Cache for Fast Disk I/O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Zhuo; Wang, Bin; Carpenter, Patrick

2012-01-01

Flash based solid-state devices (FSSDs) have been adopted within the memory hierarchy to improve the performance of hard disk drive (HDD) based storage system. However, with the fast development of storage-class memories, new storage technologies with better performance and higher write endurance than FSSDs are emerging, e.g., phase-change memory (PCM). Understanding how to leverage these state-of-the-art storage technologies for modern computing systems is important to solve challenging data intensive computing problems. In this paper, we propose to leverage PCM for a hybrid PCM-HDD storage architecture. We identify the limitations of traditional LRU caching algorithms for PCM-based caches, and develop amore » novel hash-based write caching scheme called HALO to improve random write performance of hard disks. To address the limited durability of PCM devices and solve the degraded spatial locality in traditional wear-leveling techniques, we further propose novel PCM management algorithms that provide effective wear-leveling while maximizing access parallelism. We have evaluated this PCM-based hybrid storage architecture using applications with a diverse set of I/O access patterns. Our experimental results demonstrate that the HALO caching scheme leads to an average reduction of 36.8% in execution time compared to the LRU caching scheme, and that the SFC wear leveling extends the lifetime of PCM by a factor of 21.6.« less

Energy storage options for space power

NASA Astrophysics Data System (ADS)

Hoffman, H. W.; Martin, J. F.; Olszewski, M.

Including energy storage in a space power supply enhances the feasibility of using thermal power cycles (Rankine or Brayton) and providing high-power pulses. Superconducting magnets, capacitors, electrochemical batteries, thermal phase-change materials (PCM), and flywheels are assessed; the results obtained suggest that flywheels and phase-change devices hold the most promise. Latent heat storage using inorganic salts and metallic eutectics offers thermal energy storage densities of 1500 kJ/kg to 2000 kJ/kg at temperatures to 1675 K. Innovative techniques allow these media to operate in direct contact with the heat engine working fluid. Enhancing thermal conductivity and/or modifying PCM crystallization habit provide other options. Flywheels of low-strain graphite and Kevlar fibers have achieved mechanical energy storage densities of 300 kJ/kg. With high-strain graphite fibers, storage densities appropriate to space power needs (about 500 kJ/kg) seem feasible. Coupling advanced flywheels with emerging high power density homopolar generators and compulsators could result in electric pulse-power storage modules of significantly higher energy density.

Solvent effects on the relative stability of radicals derived from artemisinin: DFT study using the PCM/COSMO approach

NASA Astrophysics Data System (ADS)

Araujo, M. T. De; Carneiro, J. W. De M.; Taranto, A. G.

The PCM/COSMO approach was employed to calculate the relative stability of radicals derived from the antimalarial artemisinin. The calculations were performed in polar (water) and apolar (THF) solvent at the density functional level [B3LYP/6-31g(d)]. Relative stabilities were calculated by means of isodesmic equations using artemisinin as reference. Replacement of oxygen atoms by CH2 unities was found to decrease the relative stability of the anionic radical intermediates. The degree of destabilization is reduced in the presence of solvent, being less in water than in THF. The dipole moment and the corresponding solvation free energies of these species modulate this effect. Derivatives with inverted stereochemistry are more stable than those with the artemisinin-like stereochemistry, although the solvent attenuates this stabilization effect. As was found in the in vacuo calculations, the radicals centered on carbon are always more stable than the corresponding radicals centered on oxygen.

Phase-change memory: A continuous multilevel compact model of subthreshold conduction and threshold switching

NASA Astrophysics Data System (ADS)

Pigot, Corentin; Gilibert, Fabien; Reyboz, Marina; Bocquet, Marc; Zuliani, Paola; Portal, Jean-Michel

2018-04-01

Phase-change memory (PCM) compact modeling of the threshold switching based on a thermal runaway in Poole–Frenkel conduction is proposed. Although this approach is often used in physical models, this is the first time it is implemented in a compact model. The model accuracy is validated by a good correlation between simulations and experimental data collected on a PCM cell embedded in a 90 nm technology. A wide range of intermediate states is measured and accurately modeled with a single set of parameters, allowing multilevel programing. A good convergence is exhibited even in snapback simulation owing to this fully continuous approach. Moreover, threshold properties extraction indicates a thermally enhanced switching, which validates the basic hypothesis of the model. Finally, it is shown that this model is compliant with a new drift-resilient cell-state metric. Once enriched with a phase transition module, this compact model is ready to be implemented in circuit simulators.

Cancer genomics: technology, discovery, and translation.

PubMed

Tran, Ben; Dancey, Janet E; Kamel-Reid, Suzanne; McPherson, John D; Bedard, Philippe L; Brown, Andrew M K; Zhang, Tong; Shaw, Patricia; Onetto, Nicole; Stein, Lincoln; Hudson, Thomas J; Neel, Benjamin G; Siu, Lillian L

2012-02-20

In recent years, the increasing awareness that somatic mutations and other genetic aberrations drive human malignancies has led us within reach of personalized cancer medicine (PCM). The implementation of PCM is based on the following premises: genetic aberrations exist in human malignancies; a subset of these aberrations drive oncogenesis and tumor biology; these aberrations are actionable (defined as having the potential to affect management recommendations based on diagnostic, prognostic, and/or predictive implications); and there are highly specific anticancer agents available that effectively modulate these targets. This article highlights the technology underlying cancer genomics and examines the early results of genome sequencing and the challenges met in the discovery of new genetic aberrations. Finally, drawing from experiences gained in a feasibility study of somatic mutation genotyping and targeted exome sequencing led by Princess Margaret Hospital-University Health Network and the Ontario Institute for Cancer Research, the processes, challenges, and issues involved in the translation of cancer genomics to the clinic are discussed.

The Drosophila Pericentrin-like-protein (PLP) cooperates with Cnn to maintain the integrity of the outer PCM

PubMed Central

Richens, Jennifer H.; Barros, Teresa P.; Lucas, Eliana P.; Peel, Nina; Pinto, David Miguel Susano; Wainman, Alan; Raff, Jordan W.

2015-01-01

ABSTRACT Centrosomes comprise a pair of centrioles surrounded by a matrix of pericentriolar material (PCM). In vertebrate cells, Pericentrin plays an important part in mitotic PCM assembly, but the Drosophila Pericentrin-like protein (PLP) appears to have a more minor role in mitotic fly cells. Here we investigate the function of PLP during the rapid mitotic cycles of the early Drosophila embryo. Unexpectedly, we find that PLP is specifically enriched in the outer-most regions of the PCM, where it largely co-localizes with the PCM scaffold protein Cnn. In the absence of PLP the outer PCM appears to be structurally weakened, and it rapidly disperses along the centrosomal microtubules (MTs). As a result, centrosomal MTs are subtly disorganized in embryos lacking PLP, although mitosis is largely unperturbed and these embryos develop and hatch at near-normal rates. Y2H analysis reveals that PLP can potentially form multiple interactions with itself and with the PCM recruiting proteins Asl, Spd-2 and Cnn. A deletion analysis suggests that PLP participates in a complex network of interactions that ultimately help to strengthen the PCM. PMID:26157019

The Drosophila Pericentrin-like-protein (PLP) cooperates with Cnn to maintain the integrity of the outer PCM.

PubMed

Richens, Jennifer H; Barros, Teresa P; Lucas, Eliana P; Peel, Nina; Pinto, David Miguel Susano; Wainman, Alan; Raff, Jordan W

2015-07-08

Centrosomes comprise a pair of centrioles surrounded by a matrix of pericentriolar material (PCM). In vertebrate cells, Pericentrin plays an important part in mitotic PCM assembly, but the Drosophila Pericentrin-like protein (PLP) appears to have a more minor role in mitotic fly cells. Here we investigate the function of PLP during the rapid mitotic cycles of the early Drosophila embryo. Unexpectedly, we find that PLP is specifically enriched in the outer-most regions of the PCM, where it largely co-localizes with the PCM scaffold protein Cnn. In the absence of PLP the outer PCM appears to be structurally weakened, and it rapidly disperses along the centrosomal microtubules (MTs). As a result, centrosomal MTs are subtly disorganized in embryos lacking PLP, although mitosis is largely unperturbed and these embryos develop and hatch at near-normal rates. Y2H analysis reveals that PLP can potentially form multiple interactions with itself and with the PCM recruiting proteins Asl, Spd-2 and Cnn. A deletion analysis suggests that PLP participates in a complex network of interactions that ultimately help to strengthen the PCM. © 2015. Published by The Company of Biologists Ltd.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1992-04-21

A free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7 [times] 10[sup [minus]3] to about 7 [times] 10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 9 figs.

Design and Testing of a Thermal Storage System for Electric Vehicle Cabin Heating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Mingyu; WolfeIV, Edward; Craig, Timothy

Without the waste heat available from the engine of a conventional automobile, electric vehicles (EVs) must provide heat to the cabin for climate control using energy stored in the vehicle. In current EV designs, this energy is typically provided by the traction battery. In very cold climatic conditions, the power required to heat the EV cabin can be of a similar magnitude to that required for propulsion of the vehicle. As a result, the driving range of an EV can be reduced very significantly during winter months, which limits consumer acceptance of EVs and results in increased battery costs tomore » achieve a minimum range while ensuring comfort to the EV driver. To minimize the range penalty associated with EV cabin heating, a novel climate control system that includes thermal energy storage has been designed for use in EVs and plug-in hybrid electric vehicles (PHEVs). The system uses the stored latent heat of an advanced phase change material (PCM) to provide cabin heating. The PCM is melted while the EV is connected to the electric grid for charging of the electric battery, and the stored energy is subsequently transferred to the cabin during driving. To minimize thermal losses when the EV is parked for extended periods, the PCM is encased in a high performance insulation system. The electrical PCM-Assisted Thermal Heating System (ePATHS) was designed to provide enough thermal energy to heat the EV s cabin for approximately 46 minutes, covering the entire daily commute of a typical driver in the U.S.« less

Using the tabulated diffusion flamelet model ADF-PCM to simulate a lifted methane-air jet flame

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michel, Jean-Baptiste; Colin, Olivier; Angelberger, Christian

2009-07-15

Two formulations of a turbulent combustion model based on the approximated diffusion flame presumed conditional moment (ADF-PCM) approach [J.-B. Michel, O. Colin, D. Veynante, Combust. Flame 152 (2008) 80-99] are presented. The aim is to describe autoignition and combustion in nonpremixed and partially premixed turbulent flames, while accounting for complex chemistry effects at a low computational cost. The starting point is the computation of approximate diffusion flames by solving the flamelet equation for the progress variable only, reading all chemical terms such as reaction rates or mass fractions from an FPI-type look-up table built from autoigniting PSR calculations using complexmore » chemistry. These flamelets are then used to generate a turbulent look-up table where mean values are estimated by integration over presumed probability density functions. Two different versions of ADF-PCM are presented, differing by the probability density functions used to describe the evolution of the stoichiometric scalar dissipation rate: a Dirac function centered on the mean value for the basic ADF-PCM formulation, and a lognormal function for the improved formulation referenced ADF-PCM{chi}. The turbulent look-up table is read in the CFD code in the same manner as for PCM models. The developed models have been implemented into the compressible RANS CFD code IFP-C3D and applied to the simulation of the Cabra et al. experiment of a lifted methane jet flame [R. Cabra, J. Chen, R. Dibble, A. Karpetis, R. Barlow, Combust. Flame 143 (2005) 491-506]. The ADF-PCM{chi} model accurately reproduces the experimental lift-off height, while it is underpredicted by the basic ADF-PCM model. The ADF-PCM{chi} model shows a very satisfactory reproduction of the experimental mean and fluctuating values of major species mass fractions and temperature, while ADF-PCM yields noticeable deviations. Finally, a comparison of the experimental conditional probability densities of the progress variable for a given mixture fraction with model predictions is performed, showing that ADF-PCM{chi} reproduces the experimentally observed bimodal shape and its dependency on the mixture fraction, whereas ADF-PCM cannot retrieve this shape. (author)« less

Controllable Thermal Rectification Realized in Binary Phase Change Composites

PubMed Central

Chen, Renjie; Cui, Yalong; Tian, He; Yao, Ruimin; Liu, Zhenpu; Shu, Yi; Li, Cheng; Yang, Yi; Ren, Tianling; Zhang, Gang; Zou, Ruqiang

2015-01-01

Phase transition is a natural phenomenon happened around our daily life, represented by the process from ice to water. While melting and solidifying at a certain temperature, a high heat of fusion is accompanied, classified as the latent heat. Phase change material (PCM) has been widely applied to store and release large amount of energy attributed to the distinctive thermal behavior. Here, with the help of nanoporous materials, we introduce a general strategy to achieve the binary eicosane/PEG4000 stuffed reduced graphene oxide aerogels, which has two ends with different melting points. It's successfully demonstrated this binary PCM composites exhibits thermal rectification characteristic. Partial phase transitions within porous networks instantaneously result in one end of the thermal conductivity saltation at a critical temperature, and therefore switch on or off the thermal rectification with the coefficient up to 1.23. This value can be further raised by adjusting the loading content of PCM. The uniqueness of this device lies in its performance as a normal thermal conductor at low temperature, only exhibiting rectification phenomenon when temperature is higher than a critical value. The stated technology has broad applications for thermal energy control in macroscopic scale such as energy-efficiency building or nanodevice thermal management. PMID:25748640

Controllable Thermal Rectification Realized in Binary Phase Change Composites

NASA Astrophysics Data System (ADS)

Chen, Renjie; Cui, Yalong; Tian, He; Yao, Ruimin; Liu, Zhenpu; Shu, Yi; Li, Cheng; Yang, Yi; Ren, Tianling; Zhang, Gang; Zou, Ruqiang

2015-03-01

Phase transition is a natural phenomenon happened around our daily life, represented by the process from ice to water. While melting and solidifying at a certain temperature, a high heat of fusion is accompanied, classified as the latent heat. Phase change material (PCM) has been widely applied to store and release large amount of energy attributed to the distinctive thermal behavior. Here, with the help of nanoporous materials, we introduce a general strategy to achieve the binary eicosane/PEG4000 stuffed reduced graphene oxide aerogels, which has two ends with different melting points. It's successfully demonstrated this binary PCM composites exhibits thermal rectification characteristic. Partial phase transitions within porous networks instantaneously result in one end of the thermal conductivity saltation at a critical temperature, and therefore switch on or off the thermal rectification with the coefficient up to 1.23. This value can be further raised by adjusting the loading content of PCM. The uniqueness of this device lies in its performance as a normal thermal conductor at low temperature, only exhibiting rectification phenomenon when temperature is higher than a critical value. The stated technology has broad applications for thermal energy control in macroscopic scale such as energy-efficiency building or nanodevice thermal management.

[Current Research Activities on Person-Centered Medicine in Academic Institutes of General Practice in Germany and Austria].

PubMed

Weber, Annemarie; Schelling, Jörg; Kohls, Niko; van Dyck, Marcus; Poggenburg, Stephanie; Vajda, Christian; Hirsch, Jameson; Sirois, Fuschia; Toussaint, Loren; Offenbächer, Martin

2017-10-11

Aim of study Person-centered medicine (PCM) with its focus on humanistic-biographical-oriented medicine and integrated, positive-salutogenic health is a central aspect in the patient-physician relationship in general practice. The objective of this analysis is to assess the prevalence and type of research project in academic institutions of general practice in Germany (Ger) and Austria (At) and the thematic priorities of the projects in the areas PCM, health promotion (HP), prevention (PRE) and conventional medicine (CM). Methods A search was conducted (September-December 2015) on the websites of 30 institutes and divisions of general medicine for their current research projects. The retrieved projects were assigned to five categories: PCM, HP, PRE, CM and others. Subsequently, we identified the targeted patient groups of the projects as well as the thematic focus in the categories PCM, HP, PRE and CM with focus on PCM and HP. Results 541 research projects were identified, 452 in Germany and 89 in Austria. Research projects were only included if they were explicitly indicated as research-oriented. Seventy projects addressed PCM aspects, 15 projects HP aspects, 32 projects PRE aspects and 396 projects CM aspects. The most frequently target groups in the categories PCM (24 of 70) and HP (7 of 15) were chronically ill patients. The most common thematic focus in PCM was communication (13 of 70) and in HP, physical activity (6 of 15). Conclusion The vast majority of research projects investigated conventional medical topics. The percentage of research activities in the field of PCM (13%) or PCM including HP (16%) in Ger and At is below the European average of 20%. From our point of view, PCM and HP need to be implemented to a greater extent in general practice. © Georg Thieme Verlag KG Stuttgart · New York.

Effect of Polysaccharide from Cordyceps militaris (Ascomycetes) on Physical Fatigue Induced by Forced Swimming.

PubMed

Xu, Yan-Feng

2016-01-01

Cordyceps militaris is the one of the most important medicinal mushrooms, widely used in East Asian countries. Polysaccharide is considered to be the principal active component in C. militaris and has a wide range of biological and pharmacological properties. This study was undertaken to investigate the effect of polysaccharide from C. militaris (PCM) on physical fatigue induced in animals through a forced swimming test. The mice were divided into 4 groups receiving 28 days' treatment with drinking water (exercise control) or low-, medium-, and high-dose PCM (40, 80, and 160 mg/kg/day, respectively). After 28 days, the mice were subjected to the forced swimming test; the exhaustive swimming time was measured and fatigue-related biochemical parameters, including serum lactic acid, urea nitrogen, creatine kinase, alanine aminotransferase, aspartate aminotransferase, superoxide dismutase, glutathi- one peroxidase, catalase, malondialdehyde, liver glycogen, and muscle glycogen, were analyzed. The results showed that PCM could significantly prolong the exhaustive swimming time of mice; decrease concentrations of serum lactic acid, urea nitrogen, creatine kinase, aspartate aminotransferase, alanine aminotransferase, and malondialdehyde; and increase liver and muscle glycogen contents and the concentrations of serum superoxide dismutase, glutathione per- oxidase, and catalase. The data suggest that PCM has an antifatigue effect, and it might become a new functional food or medicine for fatigue resistance.

Using Pre-Melted Phase Change Material to Keep Payloads in Space Warm for Hours without Power

NASA Technical Reports Server (NTRS)

Choi, Michael

2013-01-01

Adding phase change material (PCM) to a mission payload can maintain its temperature above the cold survival limit, without power, for several hours in space. For the International Space Station, PCM is melted by heaters just prior to the payload translation to the worksite when power is available. When power is cut off during the six-hour translation, the PCM releases its latent heat to make up the heat loss from the radiator(s) to space. For the interplanetary Probe, PCM is melted by heaters just prior to separation from the orbiter when power is available from the orbiter power system. After the Probe separates from the orbiter, the PCM releases its latent heat to make up the heat loss from the Probe exterior to space. Paraffin wax is a good PCM candidate.

The storage system of PCM based on random access file system

NASA Astrophysics Data System (ADS)

Han, Wenbing; Chen, Xiaogang; Zhou, Mi; Li, Shunfen; Li, Gezi; Song, Zhitang

2016-10-01

Emerging memory technologies such as Phase change memory (PCM) tend to offer fast, random access to persistent storage with better scalability. It's a hot topic of academic and industrial research to establish PCM in storage hierarchy to narrow the performance gap. However, the existing file systems do not perform well with the emerging PCM storage, which access storage medium via a slow, block-based interface. In this paper, we propose a novel file system, RAFS, to bring about good performance of PCM, which is built in the embedded platform. We attach PCM chips to the memory bus and build RAFS on the physical address space. In the proposed file system, we simplify traditional system architecture to eliminate block-related operations and layers. Furthermore, we adopt memory mapping and bypassed page cache to reduce copy overhead between the process address space and storage device. XIP mechanisms are also supported in RAFS. To the best of our knowledge, we are among the first to implement file system on real PCM chips. We have analyzed and evaluated its performance with IOZONE benchmark tools. Our experimental results show that the RAFS on PCM outperforms Ext4fs on SDRAM with small record lengths. Based on DRAM, RAFS is significantly faster than Ext4fs by 18% to 250%.

Comparative fixation methods of cervical disc arthroplasty versus conventional methods of anterior cervical arthrodesis: serration, teeth, keels, or screws?

PubMed

Cunningham, Bryan W; Hu, Nianbin; Zorn, Candace M; McAfee, Paul C

2010-02-01

Using a synthetic vertebral model, the authors quantified the comparative fixation strengths and failure mechanisms of 6 cervical disc arthroplasty devices versus 2 conventional methods of cervical arthrodesis, highlighting biomechanical advantages of prosthetic endplate fixation properties. Eight cervical implant configurations were evaluated in the current investigation: 1) PCM Low Profile; 2) PCM V-Teeth; 3) PCM Modular Flange; 4) PCM Fixed Flange; 5) Prestige LP; 6) Kineflex/C disc; 7) anterior cervical plate + interbody cage; and 8) tricortical iliac crest. All PCM treatments contained a serrated implant surface (0.4 mm). The PCM V-Teeth and Prestige contained 2 additional rows of teeth, which were 1 mm and 2 mm high, respectively. The PCM Modular and Fixed Flanged devices and anterior cervical plate were augmented with 4 vertebral screws. Eight pullout tests were performed for each of the 8 conditions by using a synthetic fixation model consisting of solid rigid polyurethane foam blocks. Biomechanical testing was conducted using an 858 Bionix test system configured with an unconstrained testing platform. Implants were positioned between testing blocks, using a compressive preload of -267 N. Tensile load-to-failure testing was performed at 2.5 mm/second, with quantification of peak load at failure (in Newtons), implant surface area (in square millimeters), and failure mechanisms. The mean loads at failure for the 8 implants were as follows: 257.4 +/- 28.54 for the PCM Low Profile; 308.8 +/- 15.31 for PCM V-Teeth; 496.36 +/- 40.01 for PCM Modular Flange; 528.03+/- 127.8 for PCM Fixed Flange; 306.4 +/- 31.3 for Prestige LP; 286.9 +/- 18.4 for Kineflex/C disc; 635.53 +/- 112.62 for anterior cervical plate + interbody cage; and 161.61 +/- 16.58 for tricortical iliac crest. The anterior plate exhibited the highest load at failure compared with all other treatments (p < 0.05). The PCM Modular and Fixed Flange PCM constructs in which screw fixation was used exhibited higher pullout loads than all other treatments except the anterior plate (p < 0.05). The PCM VTeeth and Prestige and Kineflex/C implants exhibited higher pullout loads than the PCM Low Profile and tricortical iliac crest (p < 0.05). Tricortical iliac crest exhibited the lowest pullout strength, which was different from all other treatments (p < 0.05). The surface area of endplate contact, measuring 300 mm(2) (PCM treatments), 275 mm(2) (Prestige LP), 250 mm(2) (Kineflex/C disc), 180 mm(2) (plate + cage), and 235 mm(2) (tricortical iliac crest), did not correlate with pullout strength (p > 0.05). The PCM, Prestige, and Kineflex constructs, which did not use screw fixation, all failed by direct pullout. Screw fixation devices, including anterior plates, led to test block fracture, and tricortical iliac crest failed by direct pullout. These results demonstrate a continuum of fixation strength based on prosthetic endplate design. Disc arthroplasty constructs implanted using vertebral body screw fixation exhibited the highest pullout strength. Prosthetic endplates containing toothed ridges (>or= 1 mm) or keels placed second in fixation strength, whereas endplates containing serrated edges exhibited the lowest fixation strength. All treatments exhibited greater fixation strength than conventional tricortical iliac crest. The current study offers insights into the benefits of various prosthetic endplate designs, which may potentially improve acute fixation following cervical disc arthroplasty.

The IDO-AhR Axis Controls Th17/Treg Immunity in a Pulmonary Model of Fungal Infection.

PubMed

de Araújo, Eliseu Frank; Feriotti, Claudia; Galdino, Nayane Alves de Lima; Preite, Nycolas Willian; Calich, Vera Lúcia Garcia; Loures, Flávio Vieira

2017-01-01

In infectious diseases, the enzyme indoleamine 2,3 dioxygenase-1 (IDO1) that catalyzes the tryptophan (Trp) degradation along the kynurenines (Kyn) pathway has two main functions, the control of pathogen growth by reducing available Trp and immune regulation mediated by the Kyn-mediated expansion of regulatory T (Treg) cells via aryl hydrocarbon receptor (AhR). In pulmonary paracoccidioidomycosis (PCM) caused by the dimorphic fungus Paracoccidioides brasiliensis , IDO1 was shown to control the disease severity of both resistant and susceptible mice to the infection; however, only in resistant mice, IDO1 is induced by TGF-β signaling that confers a stable tolerogenic phenotype to dendritic cells (DCs). In addition, in pulmonary PCM, the tolerogenic function of plasmacytoid dendritic cells was linked to the IDO1 activity. To further evaluate the function of IDO1 in pulmonary PCM, IDO1-deficient (IDO1 -/- ) C57BL/6 mice were intratracheally infected with P. brasiliensis yeasts and the infection analyzed at three postinfection periods regarding several parameters of disease severity and immune response. The fungal loads and tissue pathology of IDO1 -/- mice were higher than their wild-type controls resulting in increased mortality rates. The evaluation of innate lymphoid cells showed an upregulated differentiation of the innate lymphoid cell 3 phenotype accompanied by a decreased expansion of ILC1 and NK cells in the lungs of infected IDO1 -/- mice. DCs from these mice expressed elevated levels of costimulatory molecules and cytokine IL-6 associated with reduced production of IL-12, TNF-α, IL-1β, TGF-β, and IL-10. This response was concomitant with a marked reduction in AhR production. The absence of IDO1 expression caused an increased influx of activated Th17 cells to the lungs with a simultaneous reduction in Th1 and Treg cells. Accordingly, the suppressive cytokines IL-10, TGF-β, IL-27, and IL-35 appeared in reduced levels in the lungs of IDO1 -/- mice. In conclusion, the immunological balance mediated by the axis IDO/AhR is fundamental to determine the balance between Th17/Treg cells and control the severity of pulmonary PCM.

Microcontroller-based underwater acoustic ECG telemetry system.

PubMed

Istepanian, R S; Woodward, B

1997-06-01

This paper presents a microcontroller-based underwater acoustic telemetry system for digital transmission of the electrocardiogram (ECG). The system is designed for the real time, through-water transmission of data representing any parameter, and it was used initially for transmitting in multiplexed format the heart rate, breathing rate and depth of a diver using self-contained underwater breathing apparatus (SCUBA). Here, it is used to monitor cardiovascular reflexes during diving and swimming. The programmable capability of the system provides an effective solution to the problem of transmitting data in the presence of multipath interference. An important feature of the paper is a comparative performance analysis of two encoding methods, Pulse Code Modulation (PCM) and Pulse Position Modulation (PPM).

Utilization of Phase Change Materials (PCM) to Reduce Energy Consumption in Buildings

DTIC Science & Technology

2011-09-14

incorporating PCM for use in building applications. Ongoing research in thermal storage in which the PCM were encapsulated in concrete, gypsum wallboard ... wallboards were made from commercial panels after a first attempt to use gypsum walls. Three types of wallboards were studied: (i) a polycarbonate panel...and compared with ordinary gypsum wallboard . Within this comparison, the PCM composite solidification temperature was 22 °C (i.e. 2 K higher than the

Solute Transport in the Bone Lacunar-Canalicular System (LCS).

PubMed

Wang, Liyun

2018-02-01

Solute transport in the lacunar-canalicular system (LCS) plays important roles in osteocyte metabolism and cell-cell signaling. This review will summarize recent studies that establish pericellular matrix (PCM), discovered inside the LCS, as a crucial regulator of solute transport in bone. Utilizing confocal imaging and mathematical modeling, recent studies successfully quantified molecular diffusion and convection in the LCS as well as the size-dependent sieving effects of the PCM, leading to the quantification of the effective PCM fiber spacing (10 to 17 nm) in murine adult bones. Perlecan/HSPG2, a large linear proteoglycan, was identified to be an essential PCM component. The PCM-filled LCS is bone's chromatographic column, where fluid/solute transport to and from the osteocytes is regulated. The chemical composition, deposition rate, and turnover rate of the osteocyte PCM should be further defined to better understand osteocyte physiology and bone metabolism.

Quantum cluster theory for the polarizable continuum model. I. The CCSD level with analytical first and second derivatives.

PubMed

Cammi, R

2009-10-28

We present a general formulation of the coupled-cluster (CC) theory for a molecular solute described within the framework of the polarizable continuum model (PCM). The PCM-CC theory is derived in its complete form, called PTDE scheme, in which the correlated electronic density is used to have a self-consistent reaction field, and in an approximate form, called PTE scheme, in which the PCM-CC equations are solved assuming the fixed Hartree-Fock solvent reaction field. Explicit forms for the PCM-CC-PTDE equations are derived at the single and double (CCSD) excitation level of the cluster operator. At the same level, explicit equations for the analytical first derivatives of the PCM basic energy functional are presented, and analytical second derivatives are also discussed. The corresponding PCM-CCSD-PTE equations are given as a special case of the full theory.

Spontaneous pneumothorax in paracoccidioidomycosis patients from an endemic area in Midwestern Brazil.

PubMed

Cabrera, Lucas G G; Santos, Aline F; Andrade, Ursulla V; Guedes, Carlos Ivan A; Oliveira, Sandra M V L; Chang, Marilene R; Mendes, Rinaldo P; Paniago, Anamaria M M

2017-02-01

Paracoccidioidomycosis (PCM) is the most important systemic mycosis in Latin America. About 80% of PCM patients are present with its chronic form. The lungs are affected in most patients with the chronic form; however, pleural involvement has rarely been reported. We describe nine cases of PCM that presented with lung involvement and spontaneous pneumothorax. All patients, except one whose condition was not investigated, were smokers. PCM was diagnosed during the pneumothorax episode in three patients, and from 3 to 16 years before the pneumothorax episode in six patients. A total of six patients underwent chest drainage and one died as a direct result of the pneumothorax. We suggest that pneumothorax, although rare, should be considered in PCM patients who present with suddenly worsening dyspnoea. PCM should also be investigated in cases of pneumothorax in adult men from mycosis-endemic areas. © 2016 Blackwell Verlag GmbH.

Low-Cost Phase Change Material for Building Envelopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abhari, Ramin

2015-08-06

A low-cost PCM process consisting of conversion of fats and oils to PCM-range paraffins, and subsequent “encapsulation” of the paraffin using conventional plastic compounding/pelletizing equipment was demonstrated. The PCM pellets produced were field-tested in a building envelope application. This involved combining the PCM pellets with cellulose insulation, whereby 33% reduction in peak heat flux and 12% reduction in heat gain was observed (average summertime performance). The selling price of the PCM pellets produced according to this low-cost process is expected to be in the $1.50-$3.00/lb range, compared to current encapsulated PCM price of about $7.00/lb. Whole-building simulations using corresponding PCMmore » thermal analysis data suggest a payback time of 8 to 16 years (at current energy prices) for an attic insulation retrofit project in the Phoenix climate area.« less

A Liquid-Liquid Thermoelectric Heat Exchanger as a Heat Pump for Testing Phase Change Material Heat Exchangers

NASA Technical Reports Server (NTRS)

Sheth, Rubik B.; Makinen, Janice; Le, Hung V.

2016-01-01

The primary objective of the Phase Change HX payload on the International Space Station (ISS) is to test and demonstrate the viability and performance of Phase Change Material Heat Exchangers (PCM HX). The system was required to pump a working fluid through a PCM HX to promote the phase change material to freeze and thaw as expected on Orion's Multipurpose Crew Vehicle. Due to limitations on ISS's Internal Thermal Control System, a heat pump was needed on the Phase Change HX payload to help with reducing the working fluid's temperature to below 0degC (32degF). This paper will review the design and development of a TEC based liquid-liquid heat exchanger as a way to vary to fluid temperature for the freeze and thaw phase of the PCM HX. Specifically, the paper will review the design of custom coldplates and sizing for the required heat removal of the HX.

Treatment of gingival recession defects using coronally advanced flap with a porcine collagen matrix compared to coronally advanced flap with connective tissue graft: a randomized controlled clinical trial.

PubMed

Cardaropoli, Daniele; Tamagnone, Lorenzo; Roffredo, Alessandro; Gaveglio, Lorena

2012-03-01

Connective tissue graft (CTG) plus coronally advanced flap (CAF) is the reference therapy for root coverage. The aim of the present study is to evaluate the use of a porcine collagen matrix (PCM) plus CAF as an alternative to CTG+CAF for the treatment of gingival recessions (REC), in a prospective randomized, controlled clinical trial. Eighteen adult patients participated in this study. The patients presented 22 single Miller's Class I or II REC, randomly assigned to the test (PCM+CAF) or control (CTG+CAF) group. REC, probing depth, clinical attachment level (CAL), and width of keratinized tissue (KG) were evaluated at 12 months. In addition, the gingival thickness (GT) was measured 1mm apical to the bottom of the sulcus. At 12 months, mean REC was 0.23 mm for test sites and 0.09 mm for control sites (P <0.01), whereas percentage of root coverage was 94.32% and 96.97%, respectively. CAL gain was 2.41 mm in test sites and 2.95 mm in control sites (P <0.01). KG gain was 1.23 mm in the test group and 1.27 mm in the control group (P <0.01). In test sites, GT changed from 0.82 to 1.82 mm, and in control sites, from 0.86 to 2.09 mm (P <0.01). Within the limits of the study, both treatment procedures resulted in significant reduction in REC at 12 months. No statistically significant differences were found between PCM+CAF and CTG+CAF with regard to any clinical parameter. The collagen matrix represents a possible alternative to CTG.

Effect of phase change material on the heat transfer rate of different building materials

NASA Astrophysics Data System (ADS)

Hasan, Mushfiq; Alam, Shahnur; Ahmed, Dewan Hasan

2017-12-01

Phase change material (PCM) is widely known as latent heat storage. A comprehensive study is carried out to investigate the effect of PCM on heat transfer rate of building materials. Paraffin is used as PCM along with different conventional building materials to investigate the heat transfer rate from the heated region to the cold region. PCM is placed along with the three different types of building materials like plaster which is well know building material in urban areas and wood and straw which are commonly used in rural areas for roofing as well as wall panel material and investigated the heat transfer rate. An experimental setup was constructed with number of rectangular shape aluminum detachable casing (as cavity) and placed side by side. Series of rectangular cavity filled with convent ional building materials and PCM and these were placed in between two chambers filled with water at different temperature. Building materials and PCM were placed in different cavities with different combinations and investigated the heat transfer rate. The results show that using the PCM along with other building materials can be used to maintain lower temperature at the inner wall and chamber of the cold region. Moreover, the placement or orientation of the building materials and PCM make significant contribution to heat transfer rate from the heated zone to the cold zone.

Additive effect of rPb27 immunization and chemotherapy in experimental paracoccidioidomycosis.

PubMed

Fernandes, Viviane C; Martins, Estefânia M N; Boeloni, Jankerle N; Coitinho, Juliana B; Serakides, Rogéria; Goes, Alfredo M

2011-03-10

Paracoccidioidomycosis, PCM, the major systemic mycosis in Latin America, is caused by the termally dimorphic fungus Paracoccidioides brasiliensis and requires extended periods of chemotherapy with a significant frequency of relapsing disease. The search for new alternatives of treatment is necessary. rPb27 is an antigenic protein from P. brasiliensis that already showed a significant protective activity as a vaccine for PCM in experimental models. The cDNA of rPb27 was subcloned into a pET-DEST 42 plasmid, expressed in E. coli with a his-tag and purified by affinity chromatography. Immunization with this recombinant protein and chemotherapy were used together in an attempt to improve treatment of PCM. For this, BALB/c mice were challenged with pathogenic P. brasiliensis strain and after immunized with rPb27, in the presence of Corynebacterium parvum and Al(OH)(3), some groups were also treated with fluconazole. After 40 days of treatment, the combined drug/rPb27 administration controlled PCM in the liver and spleen, with long lasting protection, and largely preserved tissues structures of these organs. Additionally, in the lungs after 40 days of treatment there was a significant reduction in the fungal load and size of lesions. At the same time, the levels of TNF-α were higher than infected-only mice. Moreover, significant levels of anti-rPb27 specific IgG1, IgG2a and IgG2b isotypes were detected in the sera of mice immunized with rPb27 fluconazole treated or not. These results showed an additive protective effect of rPb27 immunization and chemotherapy, suggesting that an rPb27-based vaccine can be used to enhance PCM antifungal treatment.

Experimental evaluation of passive cooling using phase change materials (PCM) for reducing overheating in public building

NASA Astrophysics Data System (ADS)

Ahmed, Abdullahi; Mateo-Garcia, Monica; McGough, Danny; Caratella, Kassim; Ure, Zafer

2018-02-01

Indoor Environmental Quality (IEQ) is essential for the health and productivity of building users. The risk of overheating in buildings is increasing due to increased density of occupancy of people and heat emitting equipment, increase in ambient temperature due to manifestation of climate change or changes in urban micro-climate. One of the solutions to building overheating is to inject some exposed thermal mass into the interior of the building. There are many different types of thermal storage materials which typically includes sensible heat storage materials such as concrete, bricks, rocks etc. It is very difficult to increase the thermal mass of existing buildings using these sensible heat storage materials. Alternative to these, there are latent heat storage materials called Phase Change Materials (PCM), which have high thermal storage capacity per unit volume of materials making them easy to implement within retrofit project. The use of Passive Cooling Thermal Energy Storage (TES) systems in the form of PCM PlusICE Solutions has been investigated in occupied spaces to improve indoor environmental quality. The work has been carried out using experimental set-up in existing spaces and monitored through the summer the months. The rooms have been monitored using wireless temperature and humidity sensors. There appears to be significant improvement in indoor temperature of up to 5°K in the room with the PCM compared to the monitored control spaces. The success of PCM for passive cooling is strongly dependent on the ventilation strategy employed in the spaces. The use of night time cooling to purge the stored thermal energy is essential for improved efficacy of the systems to reduce overheating in the spaces. The investigation is carried within the EU funded RESEEPEE project.

Non-von Neumann computing using plasmon particles interacting with phase change materials (Conference Presentation)

NASA Astrophysics Data System (ADS)

Saiki, Toshiharu

2016-09-01

Control of localized surface plasmon resonance (LSPR) excited on metal nanostructures has drawn attention for applications in dynamic switching of plasmonic devices. As a reversible active media for LSPR control, chalcogenide phase-change materials (PCMs) such as GeSbTe (GST) are promising for high-contrast robust plasmonic switching. Owing to the plasticity and the threshold behavior during both amorphization and crystallization of PCMs, PCM-based LSPR switching elements possess a dual functionality of memory and processing. Integration of LSPR switching elements so that they interact with each other will allow us to build non-von-Neumann computing devices. As a specific demonstration, we discuss the implementation of a cellular automata (CA) algorithm into interacting LSPR switching elements. In the model we propose, PCM cells, which can be in one of two states (amorphous and crystalline), interact with each other by being linked by a AuNR, whose LSPR peak wavelength is determined by the phase of PCM cells on the both sides. The CA program proceeds by irradiating with a light pulse train. The local rule set is defined by the temperature rise in the PCM cells induced by the LSPR of the AuNR, which is subject to the intensity and wavelength of the irradiating pulse. We also investigate the possibility of solving a problem analogous to the spin-glass problem by using a coupled dipole system, in which the individual coupling strengths can be modified to optimize the system so that the exact solution can be easily reached. For this algorithm, we propose an implementation based on an idea that coupled plasmon particles can create long-range spatial correlations, and the interaction of this with a phase-change material allows the coupling strength to be modified.

Active plasma release experiments

NASA Technical Reports Server (NTRS)

1986-01-01

A pulse code modulator (PCM) encoder capable of storing data onboard into the mass memory in the encoder at up to 12 megabits per second was designed and constructed. This telemetry system was programed for two successful flights. All parts of the electronic system functioned perfectly during both previous flights and the detectors performed perfectly. However, in the first flight in Pokerflat, Alaska, an electron arm did not deploy for reasons as yet unkown. The ion arm deployed perfectly and good data was acquired.

A TDM link with channel coding and digital voice.

NASA Technical Reports Server (NTRS)

Jones, M. W.; Tu, K.; Harton, P. L.

1972-01-01

The features of a TDM (time-division multiplexed) link model are described. A PCM telemetry sequence was coded for error correction and multiplexed with a digitized voice channel. An all-digital implementation of a variable-slope delta modulation algorithm was used to digitize the voice channel. The results of extensive testing are reported. The measured coding gain and the system performance over a Gaussian channel are compared with theoretical predictions and computer simulations. Word intelligibility scores are reported as a measure of voice channel performance.

Application of Pulse Code Modulation (PCM) Technology to Aircraft Dynamics Data Acquisition.

DTIC Science & Technology

1981-04-01

and 27 is a summary of pro- jected contract awards. This plan is ordered to minimize develop- ment risks and costs in the evolution of a fully qualified...160 DOTS/INCH YES YES FORTRAN CALLABLE PLOT SOFTWARE YES YES ANALYSIS SOFTWARE YES YES 206 7. RECOMM0ENDATIONS The evaluation of the results of Phase...on metallic heat strips and specific heat sinks to provide a high degree of heat conduction from the component bodies through bonded joints to the

Hydrologic Implications of Dynamical and Statistical Approaches to Downscaling Climate Model Outputs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, Andrew W; Leung, Lai R; Sridhar, V

Six approaches for downscaling climate model outputs for use in hydrologic simulation were evaluated, with particular emphasis on each method's ability to produce precipitation and other variables used to drive a macroscale hydrology model applied at much higher spatial resolution than the climate model. Comparisons were made on the basis of a twenty-year retrospective (1975–1995) climate simulation produced by the NCAR-DOE Parallel Climate Model (PCM), and the implications of the comparison for a future (2040–2060) PCM climate scenario were also explored. The six approaches were made up of three relatively simple statistical downscaling methods – linear interpolation (LI), spatial disaggregationmore » (SD), and bias-correction and spatial disaggregation (BCSD) – each applied to both PCM output directly (at T42 spatial resolution), and after dynamical downscaling via a Regional Climate Model (RCM – at ½-degree spatial resolution), for downscaling the climate model outputs to the 1/8-degree spatial resolution of the hydrological model. For the retrospective climate simulation, results were compared to an observed gridded climatology of temperature and precipitation, and gridded hydrologic variables resulting from forcing the hydrologic model with observations. The most significant findings are that the BCSD method was successful in reproducing the main features of the observed hydrometeorology from the retrospective climate simulation, when applied to both PCM and RCM outputs. Linear interpolation produced better results using RCM output than PCM output, but both methods (PCM-LI and RCM-LI) lead to unacceptably biased hydrologic simulations. Spatial disaggregation of the PCM output produced results similar to those achieved with the RCM interpolated output; nonetheless, neither PCM nor RCM output was useful for hydrologic simulation purposes without a bias-correction step. For the future climate scenario, only the BCSD-method (using PCM or RCM) was able to produce hydrologically plausible results. With the BCSD method, the RCM-derived hydrology was more sensitive to climate change than the PCM-derived hydrology.« less

Numerical investigation of PCM in vertical triplex tube thermal energy storage system for CSP applications

NASA Astrophysics Data System (ADS)

Almsater, Saleh; Saman, Wasim; Bruno, Frank

2017-06-01

Numerical study for phase change material (PCM) in high temperature vertical triplex tube thermal energy storage system (TTTESS) were performed, using ANSYS FLUENT 15. For validation purposes, numerical modelling of a low temperature PCM was initially conducted and the predicted results were compared with the numerical and experimental data from the literature. The average temperature for freezing and melting agree well with the results from the literature. The validated model for the low temperature PCM was extended to high temperature TTTESS; the supercritical CO2 as the heat transfer fluid (HTF) flows in the inside and outside tubes during the charging and discharging processes, whereas the Lithium and Potassium carbonate (Li2CO3-K2CO3) (35%-65%) as the PCM is enclosed between them. To enhance the heat transfer inside the PCM, eight fins have been incorporated between the internal and external tubes. This study also provides results demonstrating the effect of adding more fins relative to the case of no fins on the freezing and melting fraction of the PCM. Compared to 2 tank system, the TTTESS with eight fins can provide significant performance with less size.

Analysis of wallboard containing a phase change material

NASA Astrophysics Data System (ADS)

Tomlinson, J. J.; Heberle, D. P.

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified to accommodate walls that are covered with PCM plasterboard, and to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application.

Re-utilization of Industrial CO 2 for Algae Production Using a Phase Change Material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph, Brian

This is the final report of a 36-month Phase II cooperative agreement. Under this project, Touchstone Research Laboratory (Touchstone) investigated the merits of incorporating a Phase Change Material (PCM) into an open-pond algae production system that can capture and re-use the CO 2 from a coal-fired flue gas source located in Wooster, OH. The primary objective of the project was to design, construct, and operate a series of open algae ponds that accept a slipstream of flue gas from a coal-fired source and convert a significant portion of the CO 2 to liquid biofuels, electricity, and specialty products, while demonstratingmore » the merits of the PCM technology. Construction of the pilot facility and shakedown of the facility in Wooster, OH, was completed during the first two years, and the focus of the last year was on operations and the cultivation of algae. During this Phase II effort a large-scale algae concentration unit from OpenAlgae was installed and utilized to continuously harvest algae from indoor raceways. An Algae Lysing Unit and Oil Recovery Unit were also received and installed. Initial parameters for lysing nanochloropsis were tested. Conditions were established that showed the lysing operation was effective at killing the algae cells. Continuous harvesting activities yielded over 200 kg algae dry weight for Ponds 1, 2 and 4. Studies were conducted to determine the effect of anaerobic digestion effluent as a nutrient source and the resulting lipid productivity of the algae. Lipid content and total fatty acids were unaffected by culture system and nutrient source, indicating that open raceway ponds fed diluted anaerobic digestion effluent can obtain similar lipid productivities to open raceway ponds using commercial nutrients. Data were also collected with respect to the performance of the PCM material on the pilot-scale raceway ponds. Parameters such as evaporative water loss, temperature differences, and growth/productivity were tracked. The pond with the PCM material was consistently 2 to 5°C warmer than the control pond. This difference did not seem to increase significantly over time. During phase transitions for the PCM, the magnitude of the difference between the daily minimum and maximum temperatures decreased, resulting in smaller daily temperature fluctuations. A thin layer of PCM material reduced overall water loss by 74% and consistently provided algae densities that were 80% greater than the control pond.« less

Microchannel Heat Sink with Micro Encapsulated Phase Change Material (MEPCM) Slurry

DTIC Science & Technology

2009-05-31

inlet temperature of the fluid, melting range of PCM and base heat flux. 15. SUBJECT TERMS Phase Change Materials; microchannel cooling; slurry...such as particle concentration, inlet temperature of the fluid, melting range of PCM , base heat flux and base fluid. Nomenclature A Aspect ratio Ab...of fluid, J/kg.K cp,p Specific heat of MEPCM particle, J/kg.K Cp, pcm Specific heat of PCM , J/kg.K D Hydraulic diameter, m d, dp Particle diameter

Pericellular Versican Regulates the Fibroblast-Myofibroblast Transition

PubMed Central

Hattori, Noriko; Carrino, David A.; Lauer, Mark E.; Vasanji, Amit; Wylie, James D.; Nelson, Courtney M.; Apte, Suneel S.

2011-01-01

The cell and its glycosaminoglycan-rich pericellular matrix (PCM) comprise a functional unit. Because modification of PCM influences cell behavior, we investigated molecular mechanisms that regulate PCM volume and composition. In fibroblasts and other cells, aggregates of hyaluronan and versican are found in the PCM. Dermal fibroblasts from Adamts5−/− mice, which lack a versican-degrading protease, ADAMTS5, had reduced versican proteolysis, increased PCM, altered cell shape, enhanced α-smooth muscle actin (SMA) expression and increased contractility within three-dimensional collagen gels. The myofibroblast-like phenotype was associated with activation of TGFβ signaling. We tested the hypothesis that fibroblast-myofibroblast transition in Adamts5−/− cells resulted from versican accumulation in PCM. First, we noted that versican overexpression in human dermal fibroblasts led to increased SMA expression, enhanced contractility, and increased Smad2 phosphorylation. In contrast, dermal fibroblasts from Vcan haploinsufficient (Vcanhdf/+) mice had reduced contractility relative to wild type fibroblasts. Using a genetic approach to directly test if myofibroblast transition in Adamts5−/− cells resulted from increased PCM versican content, we generated Adamts5−/−;Vcanhdf/+ mice and isolated their dermal fibroblasts for comparison with dermal fibroblasts from Adamts5−/− mice. In Adamts5−/− fibroblasts, Vcan haploinsufficiency or exogenous ADAMTS5 restored normal fibroblast contractility. These findings demonstrate that altering PCM versican content through proteolytic activity of ADAMTS5 profoundly influenced the dermal fibroblast phenotype and may regulate a phenotypic continuum between the fibroblast and its alter ego, the myofibroblast. We propose that a physiological function of ADAMTS5 in dermal fibroblasts is to maintain optimal versican content and PCM volume by continually trimming versican in hyaluronan-versican aggregates. PMID:21828051

Brain and retinal ferroportin 1 dysregulation in polycythaemia mice.

PubMed

Iacovelli, Jared; Mlodnicka, Agnieska E; Veldman, Peter; Ying, Gui-Shuang; Dunaief, Joshua L; Schumacher, Armin

2009-09-15

Disruption of iron homeostasis within the central nervous system (CNS) can lead to profound abnormalities during both development and aging in mammals. The radiation-induced polycythaemia (Pcm) mutation, a 58-bp microdeletion in the promoter region of ferroportin 1 (Fpn1), disrupts transcriptional and post-transcriptional regulation of this pivotal iron transporter. This regulatory mutation induces dynamic alterations in peripheral iron homeostasis such that newborn homozygous Pcm mice exhibit iron deficiency anemia with increased duodenal Fpn1 expression while adult homozygotes display decreased Fpn1 expression and anemia despite organismal iron overload. Herein we report the impact of the Pcm microdeletion on iron homeostasis in two compartments of the central nervous system: brain and retina. At birth, Pcm homozygotes show a marked decrease in brain iron content and reduced levels of Fpn1 expression. Upregulation of transferrin receptor 1 (TfR1) in brain microvasculature appears to mediate the compensatory iron uptake during postnatal development and iron content in Pcm brain is restored to wild-type levels by 7 weeks of age. Similarly, changes in expression are transient and expression of Fpn1 and TfR1 is indistinguishable between Pcm homozygotes and wild-type by 12 weeks of age. Strikingly, the adult Pcm brain is effectively protected from the peripheral iron overload and maintains normal iron content. In contrast to Fpn1 downregulation in perinatal brain, the retina of Pcm homozygotes reveals increased levels of Fpn1 expression. While retinal morphology appears normal at birth and during early postnatal development, adult Pcm mice demonstrate a marked, age-dependent loss of photoreceptors. This phenotype demonstrates the importance of iron homeostasis in retinal health.

Brain and retinal ferroportin 1 dysregulation in polycythaemia mice

PubMed Central

Iacovelli, Jared; Mlodnicka, Agnieska E.; Veldman, Peter; Ying, Gui-Shuang; Dunaief, Joshua L.; Schumacher, Armin

2009-01-01

Disruption of iron homeostatsis within the central nervous system (CNS) can lead to profound abnormalities during both development and aging in mammals. The radiation-induced polycythaemia (Pcm) mutation, a 58-bp microdeletion in the promoter region of ferroportin 1 (Fpn1), disrupts transcriptional and post-transcriptional regulation of this pivotal iron transporter. This regulatory mutation induces dynamic alterations in peripheral iron homeostatis such that newborn homozygous Pcm mice exhibit iron deficiency anemia with increased duodenal Fpn1 expression while adult homozygotes display decreased Fpn1 expression and anemia despite organismal iron overload. Herein we report the impact of the Pcm microdeletion on iron homeostasis in two compartments of the the central nervous system: brain and retina. At birth, Pcm homozygotes show a marked decrease in brain iron content and reduced levels of Fpn1 expression. Upregulation of transferrin receptor 1 (TfR1) in brain microvasculature appears to mediate the compensatory iron uptake during postnatal development and iron content in Pcm brain is restored to wildtype levels by 7 weeks of age. Similarly, changes in expression are transient and expression of Fpn1 and TfR1 is indistinguishable between Pcm homozygotes and wildtype by 12 weeks of age. Strikingly, the adult Pcm brain is effectively protected from the peripheral iron overload and maintains normal iron content. In contrast to Fpn1 downregulation in perinatal brain, the retina of Pcm homozygotes reveals increased levels of Fpn1 expression. While retinal morphology appears normal at birth and during early postnatal development, adult Pcm mice demonstrate a marked, age-dependent loss of photoreceptors. This phenotype demonstrates the importance of iron homeostasis in retinal health. PMID:19596281

A study of the optimal transition temperatue of PCM (Phase Change Material) wallboard for solar energy storage

NASA Astrophysics Data System (ADS)

Drake, J. B.

1987-09-01

The performance of wallboard impregnated with phase change material (PCM) is considered. An ideal setting is assumed and several measures of performance discussed. With a definition of optimal performance given, the performance with respect to variation of transition temperature is studied. Results are based on computer simulations of PCM wallboard with a standard stud wall construction. The diurnal heat capacity was found to be to be overly sensitive to numerical errors for use in PCM applications. The other measures of performance, diurnal effectiveness, net collected to storage ratio, and absolute discharge flux, all indicate similar trends. It is shown that the optimal transition temperature of the PCM is strongly influenced by the amount of solar flux absorbed.

Thermal energy and economic analysis of a PCM-enhanced household envelope considering different climate zones in Morocco

NASA Astrophysics Data System (ADS)

Kharbouch, Yassine; Mimet, Abdelaziz; El Ganaoui, Mohammed; Ouhsaine, Lahoucine

2018-07-01

This study investigates the thermal energy potentials and economic feasibility of an air-conditioned family household-integrated phase change material (PCM) considering different climate zones in Morocco. A simulation-based optimisation was carried out in order to define the optimal design of a PCM-enhanced household envelope for thermal energy effectiveness and cost-effectiveness of predefined candidate solutions. The optimisation methodology is based on coupling Energyplus® as a dynamic simulation tool and GenOpt® as an optimisation tool. Considering the obtained optimum design strategies, a thermal energy and economic analysis are carried out to investigate PCMs' integration feasibility in the Moroccan constructions. The results show that the PCM-integrated household envelope allows minimising the cooling/heating thermal energy demand vs. a reference household without PCM. While for the cost-effectiveness optimisation, it has been deduced that the economic feasibility is stilling insufficient under the actual PCM market conditions. The optimal design parameters results are also analysed.

Subscale Water Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Sheth, Rubik; Hansen, Scott

2016-01-01

Supplemental heat rejection devices are required in many spacecraft as the radiators are not sized to meet the full heat rejection demand. One means of obtaining additional heat rejection is through the use of phase change material heat exchangers (PCM HX's). PCM HX's utilize phase change to store energy in unfavorable thermal environments (melting) and reject the energy in favorable environments (freezing). Traditionally, wax has been used as a PCM on spacecraft. However, water is an attractive alternative because it is capable of storing about 40% more energy per unit mass due to its higher latent heat of fusion. The significant problem in using water as a PCM is its expansion while freezing, leading to structural integrity concerns when housed in an enclosed heat exchanger volume. Significant investigation and development has taken place over the past five years to understand and overcome the problems associated with water PCM HX's. This paper reports on the final efforts by Johnson Space Center's Thermal Systems Branch to develop a water based PCM HX. The test article developed and reported on is a subscale version of the full-scale water-based PCM HX's constructed by Mezzo Technologies. The subscale unit was designed by applying prior research on freeze front propagation and previous full-scale water PCM HX development. Design modifications to the subscale unit included use of urethane bladder, decreased aspect ratio, perforated protection sheet, and use of additional mid-plates. Testing of the subscale unit was successful and 150 cycles were completed without fail.

(p)ppGpp-Dependent Persisters Increase the Fitness of Escherichia coli Bacteria Deficient in Isoaspartyl Protein Repair.

PubMed

VandenBerg, Kelsey E; Ahn, Sarah; Visick, Jonathan E

2016-09-01

The l-isoaspartyl protein carboxyl methyltransferase (PCM) repairs protein damage resulting from spontaneous conversion of aspartyl or asparaginyl residues to isoaspartate and increases long-term stationary-phase survival of Escherichia coli under stress. In the course of studies intended to examine PCM function in metabolically inactive cells, we identified pcm as a gene whose mutation influences the formation of ofloxacin-tolerant persisters. Specifically, a Δpcm mutant produced persisters for an extended period in stationary phase, and a ΔglpD mutation drastically increased persisters in a Δpcm background, reaching 23% of viable cells. The high-persister double mutant showed much higher competitive fitness than the pcm mutant in competition with wild type during long-term stationary phase, suggesting a link between persistence and the mitigation of unrepaired protein damage. We hypothesized that reduced metabolism in the high-persister strain might retard protein damage but observed no gross differences in metabolism relative to wild-type or single-mutant strains. However, methylglyoxal, which accumulates in glpD mutants, also increased fitness, suggesting a possible mechanism. High-level persister formation in the Δpcm ΔglpD mutant was dependent on guanosine pentaphosphate [(p)ppGpp] and polyphosphate. In contrast, persister formation in the Δpcm mutant was (p)ppGpp independent and thus may occur by a distinct pathway. We also observed an increase in conformationally unstable proteins in the high-persister strain and discuss this as a possible trigger for persistence as a response to unrepaired protein damage. Protein damage is an important factor in the survival and function of cells and organisms. One specific form of protein damage, the formation of the abnormal amino acid isoaspartate, can be repaired by a nearly universally conserved enzyme, PCM. PCM-directed repair is associated with stress survival and longevity in bacteria, insects, worms, plants, mice, and humans, but much remains to be learned about the specific effects of protein damage and repair. This paper identifies an unexpected connection between isoaspartyl protein damage and persisters, subpopulations in bacterial cultures showing increased tolerance to antibiotics. In the absence of PCM, the persister population in Escherichia coli bacteria increased, especially if the metabolic gene glpD was also mutated. High levels of persisters in pcm glpD double mutants correlated with increased fitness of the bacteria in a competition assay, and the fitness was dependent on the signal molecule (p)ppGpp; this may represent an alternative pathway for responding to protein damage. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

A rotor-mounted digital instrumentation system for helicopter blade flight research measurements

NASA Technical Reports Server (NTRS)

Knight, V. H., Jr.; Haywood, W. S., Jr.; Williams, M. L.

1978-01-01

A rotor mounted flight instrumentation system developed for helicopter rotor blade research is described. The system utilizes high speed digital techniques to acquire research data from miniature pressure transducers on advanced rotor airfoils which are flight tested on an AH-1G helicopter. The system employs microelectronic pulse code modulation (PCM) multiplexer digitizer stations located remotely on the blade and in a hub mounted metal canister. As many as 25 sensors can be remotely digitized by a 2.5 mm thick electronics package mounted on the blade near the tip to reduce blade wiring. The electronics contained in the canister digitizes up to 16 sensors, formats these data with serial PCM data from the remote stations, and transmits the data from the canister which is above the plane of the rotor. Data are transmitted over an RF link to the ground for real time monitoring and to the helicopter fuselage for tape recording. The complete system is powered by batteries located in the canister and requires no slip rings on the rotor shaft.

Determination of the solar transmittance for the translucent shutter with PCM in liquid and solid state

NASA Astrophysics Data System (ADS)

Komerska, Anna; Ksionek, Dariusz; Rosiński, Marian

2017-11-01

This article presents results of the energy performance of an external translucent shading component integrated with a phase change material. A proposed technology is able to accumulate considerable amounts of energy in the latent heat by absorbing solar energy. Due to selective optical properties, much of the visible light is still transmitted through the facade. Experimental measurements were carried out in a laboratory set-up - testing thermal chamber, located in the Faculty of Building Services, Hydro and Environmental Engineering at Warsaw University of Technology. The main result of the experimental study was the evaluation of the average solar transmittance in the whole measured spectrum, as well as in the infrared and visible light. Since the shift in optical properties was observed when the material was undergoing a phase transition, the average spectral transmittances were measured for different states of matter of the PCM material. The tested shutter showed abilities to reduce and modulate daylight and solar heat gains in the indoor environment, which could contribute to considerable energy savings.

Thermal Assessment of a Latent-Heat Energy Storage Module During Melting and Freezing for Solar Energy Applications

NASA Astrophysics Data System (ADS)

Ramos Archibold, Antonio

Capital investment reduction, exergetic efficiency improvement and material compatibility issues have been identified as the primary techno-economic challenges associated, with the near-term development and deployment of thermal energy storage (TES) in commercial-scale concentrating solar power plants. Three TES techniques have gained attention in the solar energy research community as possible candidates to reduce the cost of solar-generated electricity, namely (1) sensible heat storage, (2) latent heat (tank filled with phase change materials (PCMs) or encapsulated PCMs packed in a vessel) and (3) thermochemical storage. Among these the PCM macro-encapsulation approach seems to be one of the most-promising methods because of its potential to develop more effective energy exchange, reduce the cost associated with the tank and increase the exergetic efficiency. However, the technological barriers to this approach arise from the encapsulation techniques used to create a durable capsule, as well as an assessment of the fundamental thermal energy transport mechanisms during the phase change. A comprehensive study of the energy exchange interactions and induced fluid flow during melting and solidification of a confined storage medium is reported in this investigation from a theoretical perspective. Emphasis has been placed on the thermal characterization of a single constituent storage module rather than an entire storage system, in order to, precisely capture the energy exchange contributions of all the fundamental heat transfer mechanisms during the phase change processes. Two-dimensional, axisymmetric, transient equations for mass, momentum and energy conservation have been solved numerically by the finite volume scheme. Initially, the interaction between conduction and natural convection energy transport modes, in the absence of thermal radiation, is investigated for solar power applications at temperatures (300--400°C). Later, participating thermal radiation within the storage medium has been included in order to extend the conventional natural convection-dominated model and to analyze its influence on the melting and freezing dynamics at elevated temperatures (800-850°C). A parametric analysis has been performed in order to ascertain the effects of the controlling parameters on the melting/freezing rates and the total and radiative heat transfer rates at the inner surface of the shell. The results show that the presence of thermal radiation enhances the melting and solidification processes. Finally, a simplified model of the packed bed heat exchanger with multiple spherical capsules filled with the storage medium and positioned in a vertical array inside a cylindrical container is analyzed and numerically solved. The influence of the inlet mass flow rate, inner shell surface emissivity and PCM attenuation coefficient on the melting dynamics of the PCM has been analyzed and quantified.

Treatment of cervical radiculopathy: A review of the evolution and economics.

PubMed

Ament, Jared D; Karnati, Tejas; Kulubya, Edwin; Kim, Kee D; Johnson, J Patrick

2018-01-01

The surgical treatment of cervical radiculopathy has centered around anterior cervical discectomy and fusion (ACDF). Alternatively, the posterior cervical laminoforaminotomy/microdiscectomy (PCF/PCM), which results in comparable outcomes and is more cost-effective, has been underutilized. Here, we compared the direct/indirect costs, reoperation rates, and outcome for ACDF and PCF vs. PCM using PubMed, Medline, and Embase databases. There were no significant differences between the re-operative rates of PCF/PCM (2% to 9.8%) versus ACDF (2% to 8%). Direct costs of ACDF were also significantly higher; the 1-year cost-utility analysis demonstrated that ACDF had $131,951/QALY while PCM had $79,856/QALY. PCF/PCM for radiculopathy are safe and more cost-effective vs. ACDF, and have similar clinical outcomes.

Cooling Curve Analysis of Micro- and Nanographite Particle-Embedded Salt-PCMs for Thermal Energy Storage Applications

NASA Astrophysics Data System (ADS)

Sudheer, R.; Prabhu, K. N.

2017-08-01

In recent years, the focus of phase change materials (PCM) research was on the development of salt mixtures with particle additives to improve their thermal energy storage (TES) functionalities. The effect of addition of microsized (50 μm) and nanosized (400 nm) graphite particles on TES parameters of potassium nitrate was analyzed in this work. A novel technique of computer-aided cooling curve analysis was employed here to study the suitability of large inhomogeneous PCM samples. The addition of graphite micro- and nanoparticles reduced the solidification time of the PCM significantly enhancing the heat removal rates, in the first thermal cycle. The benefits of dispersing nanoparticles diminished in successive 10 thermal cycles, and its performance was comparable to the microparticle-embedded PCM thereafter. The decay of TES functionalities on thermal cycling is attributed to the agglomeration of nanoparticles which was observed in SEM images. The thermal diffusivity property of the PCM decreased with addition of graphite particles. With no considerable change in the cooling rates and a simultaneous decrease in thermal diffusivity, it is concluded that the addition of graphite particles increased the specific heat capacity of the PCM. It is also suggested that the additive concentration should not be greater than 0.1% by weight of the PCM sample.

Analysis of wallboard containing a phase change material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomlinson, J.J.; Heberle, D.P.

1990-01-01

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified tomore » accommodate walls that are covered with PCM plasterboard, nd to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application. 5 refs., 4 figs., 4 tabs.« less

Numerical investigation on thermal behaviors of two-dimensional latent thermal energy storage with PCM and aluminum foam

NASA Astrophysics Data System (ADS)

Buonomo, B.; Ercole, D.; Manca, O.; Nardini, S.

2017-01-01

A numerical investigation on Latent Heat Thermal Energy Storage System (LHTESS) based on a phase change material (PCM) is accomplished. The PCM is a pure paraffin wax with a low thermal conductivity. An aluminum metal foam is employed to enhance the PCM thermal behaviors. The geometry is a vertical shell-and-tube LHTESS made with two concentric aluminum tubes. The internal surface of the hollow cylinder is assumed at a constant temperature above the melting temperature of the PCM to simulate the heat transfer from a hot fluid. The external surface is assumed adiabatic. The phase change of the PCM is modelled with the enthalpy porosity theory while the metal foam is considered as a porous media in Darcy-Forchheimer assumption and the Boussinesq approximation is employed. Local thermal non-equilibrium (LTNE) model is assumed. The results are compared in terms of melting time and temperature fields as a function of time for the charging and discharging phases for different porosities and an assigned pore per inch. Results show that the metal foam improves significantly the heat transfer in the LHTESS giving a faster phase change process with respect to pure PCM, reducing the melting time more than one order of magnitude.

Metallic phase-change materials for solar dynamic energy storage systems

NASA Astrophysics Data System (ADS)

Lauf, R. J.; Hamby, C., Jr.

1990-12-01

Solar (thermal) dynamic power systems for satellites require a heat storage system that is capable of operating the engine during eclipse. The conventional approach to this thermal storage problem is to use the latent heat of fluoride salts, which would melt during insolation and freeze during eclipse. Although candidate fluorides have large heats of fusion per unit mass, their poor thermal conductivity limits the rate at which energy can be transferred to and from the storage device. System performance is further limited by the high parasitic mass of the superalloy canisters needed to contain the salt. A new thermal storage system is described in which the phase-change material (PCM) is a metal (typically germanium) contained in modular graphite canisters. These modules exhibit good thermal conductivity and low parasitic mass, and they are physically and chemically stable. Prototype modules have survived over 600 melt/freeze cycles without degradation. Advanced concepts to further improve performance are described. These concepts include the selection of ternary eutectic alloys to provide a wider range of useful melting temperatures and the use of infiltration to control the location of liquid alloy and to compensate for differences in thermal expansion.

All-optically tunable EIT-like dielectric metasurfaces hybridized with thin phase change material layers

NASA Astrophysics Data System (ADS)

Petronijevic, Emilija; Sibilia, Concita

2017-05-01

Electromagnetically induced transparency (EIT), a pump-induced narrow transparency window within the absorption region of a probe, had offered new perspectives in slow-light control in atomic physics. For applications in nanophotonics, the implementation on chip-scaled devices has later been obtained by mimicking this effect by metallic metamaterials. High losses in visible and near infrared range of metal-based metamaterialls have recently opened a new field of all-dielectric metamaterials; a proper configuration of high refractive index dielectric nanoresonators can mimick this effect without losses to get high Q, slow-light response. The next step would be the ability to tune their optical response, and in this work we investigate thin layers of phase change materials (PCM) for all-optical control of EIT-like all-dielectric metamaterials. PCM can be nonvolatively and reversibly switched between two stable phases that differ in optical properties by applying a visible laser pulse. The device is based on Si nanoresonators covered by a thin layer of PCM GeTe; optical and transient thermal simulations have been done to find and optimize the fabrication parameters and switching parameters such as the intensity and duration of the pulse. We have found that the EIT-like response can be switched on and off by applying the 532nm laser pulse to change the phase of the upper GeTe layer. We strongly believe that such approach could open new perspectives in all-optically controlled slow-light metamaterials.

Paracoccidioidomycosis due to Paracoccidioides brasiliensis S1 plus HIV co-infection

PubMed Central

de Macedo, Priscila Marques; Almeida-Paes, Rodrigo; Almeida, Marcos de Abreu; Coelho, Rowena Alves; Andrade, Hugo Boechat; Ferreira, Ana Beatriz Teixeira Brandão Camello; Zancopé-Oliveira, Rosely Maria; do Valle, Antonio Carlos Francesconi

2018-01-01

BACKGROUND Paracoccidioidomycosis (PCM) is one of the most important systemic mycoses in Latin America and the leading fungal cause of mortality in non-immunosuppressed individuals in Brazil. However, HIV/PCM co-infection can increase the clinical severity in these co-infected patients. This co-infection is rarely reported in the literature mainly because of the different epidemiological profiles of these infections. Furthermore, PCM is a neglected and non-notifiable disease, which may underestimate the real importance of this disease. The advent of molecular studies on the species of the genus Paracoccidioides has expanded the knowledge regarding the severity and the clinical spectrum in PCM. In this context, the development of studies to describe the association of the Paracoccidioides phylogenetic cryptic species in vulnerable populations, such as HIV-infected patients, appears relevant. OBJECTIVE To describe the clinical, epidemiological, therapeutic and prognostic aspects in HIV/PCM co-infected patients, along with the molecular identification of the Paracoccidioides species involved in these cases. METHODS The investigators performed a molecular and clinical retrospective study involving HIV/PCM co-infected patients, from a reference centre for PCM care in the endemic area of Rio de Janeiro, Brazil, from 1998 to 2015. Molecular identification of the fungal strains was done by amplification of partial sequences of arf and gp43 genes. FINDINGS Of 89 patients diagnosed with PCM by fungal isolation in the culture, a viable isolate was recovered for molecular analysis from 44 patients. Of these 44 patients, 28 (63.6%) had their serum samples submitted for enzyme immunoassay tests for screening of HIV antibodies, and 5 (17.9%) had a positive result. All cases were considered severe, with a variable clinical presentation, including mixed, acute/subacute clinical forms and a high rate of complications, requiring combination therapy. Paracoccidioides brasiliensis S1 was the species identified in all cases. CONCLUSIONS HIV/PCM co-infection can change the natural history of this fungal disease. The authors reinforce the need to include HIV screening diagnostic tests routinely for patients with PCM. PMID:29412355

Serology of Paracoccidioidomycosis Due to Paracoccidioides lutzii

PubMed Central

Gegembauer, Gregory; Araujo, Leticia Mendes; Pereira, Edy Firmina; Rodrigues, Anderson Messias; Paniago, Anamaria Mello Miranda; Hahn, Rosane Christine; de Camargo, Zoilo Pires

2014-01-01

Paracoccidioides lutzii is a new agent of paracoccidioidomycosis (PCM) and has its epicenter localized to the Central-West region of Brazil. Serological diagnosis of PCM caused by P. lutzii has not been established. This study aimed to develop new antigenic preparations from P. lutzii and to apply them in serological techniques to improve the diagnosis of PCM due to P. lutzii. Paracoccidioides lutzii exoantigens, cell free antigen (CFA), and a TCA-precipitated antigen were evaluated in immunodiffusion (ID) tests using a total of 89 patient sera from the Central-West region of Brazil. Seventy-two sera were defined as reactive for P. brasiliensis using traditional antigens (AgPbB339 and gp43). Non-reactive sera for traditional antigens (n = 17) were tested with different P. lutzii preparations and P. lutzii CFA showed 100% reactivity. ELISA was found to be a very useful test to titer anti-P. lutzii antibodies using P. lutzii-CFA preparations. Sera from patients with PCM due to P. lutzii presented with higher antibody titers than PCM due to P. brasiliensis and heterologous sera. In western blot, sera from patients with PCM due to P. lutzii were able to recognize antigenic molecules from the P. lutzii-CFA antigen, but sera from patients with PCM due to P. brasiliensis could not recognize any P. lutzii molecules. Due to the facility of preparing P. lutzii CFA antigens we recommend its use in immunodiffusion tests for the diagnosis of PCM due to P. lutzii. ELISA and western blot can be used as complementary tests. PMID:25032829

Distribution of pericellular matrix molecules in the temporomandibular joint and their chondroprotective effects against inflammation

PubMed Central

Chu, Wern Cui; Zhang, Shipin; Sng, Timothy J; Ong, Yu Jie; Tan, Wen-Li; Ang, Vivien Y; Foldager, Casper B; Toh, Wei Seong

2017-01-01

The objectives of this study were to (1) determine the distribution and synthesis of pericellular matrix (PCM) molecules (collagen VI, collagen IV and laminin) in rat temporomandibular joint (TMJ) and (2) investigate the effects of PCM molecules on chondrocytes against inflammation in osteoarthritis. Four zones (fibrous, proliferating, mature and hypertrophic) of condylar cartilage and three bands (anterior, intermediate and posterior) of disc were analysed by immunohistochemistry for the presence of PCM molecules in rat TMJs. Isolated chondrocytes were pre-treated with PCM molecules before being subjected to interleukin (IL)-1β treatment to stimulate inflammation. The responses of the chondrocytes were analysed using gene expression, nitric oxide release and matrix metalloproteinase (MMP)-13 production measures. Histomorphometric analyses revealed that the highest areal deposition of collagen VI (67.4%), collagen IV (45.7%) and laminin (52.4%) was in the proliferating zone of TMJ condylar cartilage. No significant difference in the distribution of PCM molecules was noted among the three bands of the TMJ disc. All three PCM molecules were expressed intracellularly by chondrocytes cultured in the monolayer. Among the PCM molecules, pre-treatment with collagen VI enhanced cellular proliferation, ameliorated IL-1β-induced MMP-3, MMP-9, MMP-13 and inducible nitric oxide synthase gene expression, and attenuated the downregulation of cartilage matrix genes, including collagen I, aggrecan and cartilage oligomeric matrix protein (COMP). Concurrently, collagen VI pretreatment inhibited nitric oxide and MMP-13 production. Our study demonstrates for the first time the distribution and role of PCM molecules, particularly collagen VI, in the protection of chondrocytes against inflammation. PMID:28282029

Analysis of thermal energy storage material with change-of-phase volumetric effects

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.; Ibrahim, Mounir B.

1990-01-01

NASA's Space Station Freedom proposed hybrid power system includes photovoltaic arrays with nickel hydrogen batteries for energy storage and solar dynamic collectors driving Brayton heat engines with change-of-phase Thermal Energy Storage (TES) devices. A TES device is comprised of multiple metallic, annular canisters which contain a eutectic composition LiF-CaF2 Phase Change Material (PCM) that melts at 1040 K. A moderately sophisticated LiF-CaF2 PCM computer model is being developed in three stages considering 1-D, 2-D, and 3-D canister geometries, respectively. The 1-D model results indicate that the void has a marked effect on the phase change process due to PCM displacement and dynamic void heat transfer resistance. Equally influential are the effects of different boundary conditions and liquid PCM natural convection. For the second stage, successful numerical techniques used in the 1-D phase change model are extended to a 2-D (r,z) PCM containment canister model. A prototypical PCM containment canister is analyzed and the results are discussed.

Re-examining the role of Drosophila Sas-4 in centrosome assembly using two-colour-3D-SIM FRAP

PubMed Central

Conduit, Paul T; Wainman, Alan; Novak, Zsofia A; Weil, Timothy T; Raff, Jordan W

2015-01-01

Centrosomes have many important functions and comprise a ‘mother’ and ‘daughter’ centriole surrounded by pericentriolar material (PCM). The mother centriole recruits and organises the PCM and templates the formation of the daughter centriole. It has been reported that several important Drosophila PCM-organising proteins are recruited to centrioles from the cytosol as part of large cytoplasmic ‘S-CAP’ complexes that contain the centriole protein Sas-4. In a previous paper (Conduit et al., 2014b) we showed that one of these proteins, Cnn, and another key PCM-organising protein, Spd-2, are recruited around the mother centriole before spreading outwards to form a scaffold that supports mitotic PCM assembly; the recruitment of Cnn and Spd-2 is dependent on another S-CAP protein, Asl. We show here, however, that Cnn, Spd-2 and Asl are not recruited to the mother centriole as part of a complex with Sas-4. Thus, PCM recruitment in fly embryos does not appear to require cytosolic S-CAP complexes. DOI: http://dx.doi.org/10.7554/eLife.08483.001 PMID:26530814

Background, Structure and Priorities of the 2013 Geneva Declaration on Person-centered Health Research

PubMed Central

Salvador-Carulla, Luis; Cloninger, C Robert; Thornicroft, Amalia; Mezzich, Juan E.

2015-01-01

Declarations are relevant tools to frame new areas in health care, to raise awareness and to facilitate knowledge-to-action. The International College on Person Centered Medicine (ICPCM) is seeking to extend the impact of the ICPCM Conference Series by producing a declaration on every main topic. The aim of this paper is to describe the development of the 2013 Geneva Declaration on Person-centered Health Research and to provide additional information on the research priority areas identified during this iterative process. There is a need for more PCM research and for the incorporation of the PCM approach into general health research. Main areas of research focus include: Conceptual, terminological, and ontological issues; research to enhance the empirical evidence of PCM main components such as PCM informed clinical communication; PCM-based diagnostic models; person-centered care and interventions; and people-centered care, research on training and curriculum development. Dissemination and implementation of PCM knowledge-base is integral to Person-centered Health Research and shall engage currently available scientific and translational dissemination tools such journals, events and eHealth. PMID:26146541

Simulation of passive thermal management system for lithium-ion battery packs

NASA Astrophysics Data System (ADS)

Mills, Andrew; Al-Hallaj, Said

A passive thermal management system that uses a phase change material (PCM) is designed and simulated for a lithium-ion (Li-ion) laptop battery pack. The problem of low thermal conductivity of the PCM was significantly improved by impregnating an expanded graphite (EG) matrix with the PCM. The heat generation rate for a commercial 186502.2 Ah Li-ion battery was experimentally measured for various constant power discharges. Simulation of the battery pack, composed of six Li-ion batteries, shows that safe operation of the battery pack during the most extreme case requires the volume of the battery pack be almost doubled to fit sufficient PCM in the pack. Improving the properties of the PCM composite have the potential to significantly reduce the volume increase in comparison to the original battery pack volume.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1993-05-18

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the p.c.m. must be added to the silica in an amount of 80 wt. % or less p.c.m. per combined weight of silica and p.c.m. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a p.c.m. material. The silica-p.c.m. mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

A study of the optimal transition temperature of PCM (phase change material) wallboard for solar energy storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drake, J.B.

1987-09-01

In this report, we consider the performance of wallboard impregnated with phase change material. An ideal setting is assumed and several measures of performance discussed. With a definition of optimal performance given, the performance with respect to variation of transition temperature is studied. Results are based on computer simulations of PCM wallboard with a standard stud wall construction. We find the diurnal heat capacity to be overly sensitive to numerical errors for use in PCM applications. The other measures of performance, diurnal effectiveness, net collected to storage ratio, and absolute discharge flux, all indicate similar trends. It is shown thatmore » the optimal transition temperature of the PCM is strongly influenced by amount of solar flux absorbed by the PCM. 6 refs., 5 figs., 5 tabs.« less

Subtractive phage display selection for screening and identification of peptide sequences with potential use in serodiagnosis of paracoccidioidomycosis caused by Paracoccidioides brasiliensis.

PubMed

Portes, L da Silva; Kioshima, E S; de Camargo, Z P; Batista, W L; Xander, P

2017-11-01

Paracoccidioidomycosis (PCM) is a systemic granulomatous disease endemic in Latin America whose aetiologic agents are the thermodimorphic fungi Paracoccidioides brasiliensis and Paracoccidioides lutzii. Despite technological advances, some problems have been reported for the fungal antigens used for serological diagnosis, and inconsistencies among laboratories have been reported. The use of synthetic peptides in the serological diagnosis of infectious diseases has proved to be a valuable strategy because in some cases, the reactions are more specific and sensitive. In this study, we used a subtractive selection with a phage display library against purified polyclonal antibodies for negative and positive PCM sera caused by P. brasiliensis. The binding phages were sequenced and tested in a binding assay to evaluate its interaction with sera from normal individuals and PCM patients. Synthetic peptides derived from these phage clones were tested in a serological assay, and we observed a significant recognition of LP15 by sera from PCM patients infected with P. brasiliensis. Our results demonstrated that subtractive phage display selection may be useful for identifying new epitopes that can be applied to the serodiagnosis of PCM caused by P. brasiliensis. Currently, there is no standardized method for the preparation of paracoccidioidomycosis (PCM) antigens, which has resulted in differences in the antigens used for serological diagnosis. Here, we report a procedure that uses subtractive phage display selection to select and identify new epitopes for the serodiagnosis of PCM caused by Paracoccidioides brasiliensis. A synthetic peptide obtained using this methodology was successfully recognized by sera from PCM patients, thus demonstrating its potential use for improving the serodiagnosis of this mycosis. The development of synthetic peptides for the serodiagnosis of PCM could be a promising alternative for the better standardization of diagnoses among laboratories. © 2017 The Society for Applied Microbiology.

Study on the optimum PCM melting temperature for energy savings in residential buildings worldwide

NASA Astrophysics Data System (ADS)

Saffari, M.; de Gracia, A.; Fernández, C.; Zsembinszki, G.; Cabeza, L. F.

2017-10-01

To maintain comfort conditions in residential buildings along a full year period, the use of active systems is generally required to either supply heating or cooling. The heating and cooling demands strongly depend on the climatic conditions, type of building and occupants’ behaviour. The overall annual energy consumption of the building can be reduced by the use of renewable energy sources and/or passive systems. The use of phase change materials (PCM) as passive systems in buildings enhances the thermal mass of the envelope, and reduces the indoor temperature fluctuations. As a consequence, the overall energy consumption of the building is generally lower as compared to the case when no PCM systems are used. The selection of the PCM melting temperature is a key issue to reduce the energy consumption of the buildings. The main focus of this study is to determine the optimum PCM melting temperature for passive heating and cooling according to different weather conditions. To achieve that, numerical simulations were carried out using EnergyPlus v8.4 coupled with GenOpt® v3.1.1 (a generic optimization software). A multi-family residential apartment was selected from ASHRAE Standard 90.1- 2013 prototype building model, and different climate conditions were considered to determine the optimum melting temperature (in the range from 20ºC to 26ºC) of the PCM contained in gypsum panels. The results confirm that the optimum melting temperature of the PCM strongly depends on the climatic conditions. In general, in cooling dominant climates the optimum PCM temperature is around 26ºC, while in heating dominant climates it is around 20ºC. Furthermore, the results show that an adequate selection of the PCM as passive system in building envelope can provide important energy savings for both heating dominant and cooling dominant regions.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1994-01-01

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1995-01-01

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

The relation between FoxP3⁺ regulatory T cells and fungal density in oral paracoccidioidomycosis: a preliminary study.

PubMed

Cardoso, Rhanderson Miller Nascimento; Jham, Bruno Correia; do Carmo, Gabriela Mota; Batista, Aline Carvalho; de Oliveira, Flávia Aparecida; de Paula, Elbio Candido; Mesquita, Ricardo Alves; da Silva, Tarcília Aparecida; Duarte, Eliza Carla Barroso

2014-12-01

Regulatory T (Treg) cells may play an important role in the pathogenesis of paracoccidioidomycosis (PCM), but data on the role of Treg cells in the context of oral PCM are still scarce. The objectives of this study were to investigate the density of FoxP3(+) T regulatory cells in oral PCM and to correlate the results with the density of Paracoccidioides brasiliensis in the lesions. Cases of chronic oral PCM seen between 2000 and 2008 were included in this study. The diagnosis of all lesions was confirmed with histopathological examination and Grocott-Gomori staining. The quantitative analysis of the viable fungi was conducted in all cases with Grocott-stained slides. Treg cells were identified using antibodies against FoxP3. Pearson correlation coefficient was used to test the correlation between the density of fungi and Treg cells. Results were considered significant when P < 0.05. A total of 11 cases of oral PCM were obtained. There was a positive correlation between fungal density and FoxP3(+) Treg cells density in oral lesions, however, without statistical significance. A positive relation between Treg cells and fungal density was seen in oral PCM. Further studies are required to further elucidate the role of these cells in the pathogenesis of oral PCM, as well the clinical significance of these findings. © 2014 Blackwell Verlag GmbH.

Influence of PCMs in thermal insulation on thermal behaviour of building envelopes

NASA Astrophysics Data System (ADS)

Dydek, K.; Furmański, P.; Łapka, P.

2016-09-01

A model of heat transfer through a wall consisting of a layer of concrete and PCM enhanced thermal insulation is considered. The model accounts for heat conduction in both layers, thermal radiation and heat absorption/release due to phase change in the insulation as well as time variation in the ambient temperature and insolation. Local thermal equilibrium between encapsulated PCM and light-weight thermal insulation was assumed. Radiation emission, absorption and scattering were also accounted for in the model. Comparison of different cases of heat flow through the building envelope was carried out. These cases included presence or absence of PCM and thermal radiation in the insulation, effect of emissivity of the PCM microcapsules as well as an effect of solar radiation or its lack on the ambient side of the envelope. Two ways of the PCM distribution in thermal insulation were also considered. The results of simulations were presented for conditions corresponding to the mean summer and winter seasons in Warsaw. It was found that thermal radiation plays an important role in heat transfer through thermal insulation layer of the wall while the presence of the PCM in it significantly contributes to damping of temperature fluctuations and a decrease in heat fluxes flowing into or lost by the interior of the building. The similar effect was observed for a decrease in emissivity of the microcapsules containing PCM.

Effect of PCM on the Hydration Process of Cement-Based Mixtures: A Novel Thermo-Mechanical Investigation.

PubMed

Fabiani, Claudia; Pisello, Anna Laura; D'Alessandro, Antonella; Ubertini, Filippo; Cabeza, Luisa F; Cotana, Franco

2018-05-23

The use of Phase Change Material (PCM) for improving building indoor thermal comfort and energy saving has been largely investigated in the literature in recent years, thus confirming PCM’s capability to reduce indoor thermal fluctuation in both summer and winter conditions, according to their melting temperature and operation boundaries. Further to that, the present paper aims at investigating an innovative use of PCM for absorbing heat released by cement during its curing process, which typically contributes to micro-cracking of massive concrete elements, therefore compromising their mechanical performance during their service life. The experiments carried out in this work showed how PCM, even in small quantities (i.e., up to 1% in weight of cement) plays a non-negligible benefit in reducing differential thermal increases between core and surface and therefore mechanical stresses originating from differential thermal expansion, as demonstrated by thermal monitoring of cement-based cubes. Both PCM types analyzed in the study (with melting temperatures at 18 and 25 ∘ C) were properly dispersed in the mix and were shown to be able to reduce the internal temperature of the cement paste by several degrees, i.e., around 5 ∘ C. Additionally, such small amount of PCM produced a reduction of the final density of the composite and an increase of the characteristic compressive strength with respect to the plain recipe.

Visual monitoring of the melting front propagation in a paraffin-based PCM

NASA Astrophysics Data System (ADS)

Charvát, Pavel; Štětina, Josef; Mauder, Tomáš; Klimeš, Lubomír

Experiments were carried out in an environmental chamber with the aim to monitor the melting front propagation in a rectangular cavity filled with a paraffin-based Phase Change Material (PCM). The PCM was contained in transparent containers with the heat flux introduced by means of an electric heating element. The stabilized power source was used to maintain the constant heat output of the heating elements. The experiments were performed for the heat flux introduced at the side wall of the container and at the upper surface of the PCM. The paraffin-based PCM RT28HC with the phase change temperature of 28 °C was used in the experiments. The temperature in the environmental chamber was maintained at the melting temperature of the PCM. The propagation of the melting front was monitored with a digital camera and temperatures at several locations were monitored with RTDs and thermocouples. Significant natural convection was observed for the heat flux introduced at the side wall of the container. As a result the melting front propagated much faster at the top of the container than at its bottom. The heat flux introduced at the upper-surface of the PCM resulted in almost one-dimensional propagation of the melting front. The acquired data are to be used for validation of an in-house developed numerical model based on the front-tracking method.

Cooling vests with phase change materials: the effects of melting temperature on heat strain alleviation in an extremely hot environment.

PubMed

Gao, Chuansi; Kuklane, Kalev; Holmér, Ingvar

2011-06-01

A previous study by the authors using a heated thermal manikin showed that the cooling rates of phase change material (PCM) are dependent on temperature gradient, mass, and covering area. The objective of this study was to investigate if the cooling effects of the temperature gradient observed on a thermal manikin could be validated on human subjects in extreme heat. The subjects wore cooling vests with PCMs at two melting temperatures (24 and 28°C) and fire-fighting clothing and equipment, thus forming three test groups (vest24, vest28 and control group without the vest). They walked on a treadmill at a speed of 5 km/h in a climatic chamber (air temperature = 55°C, relative humidity = 30%, vapour pressure = 4,725 Pa, and air velocity = 0.4 m/s). The results showed that the PCM vest with a lower melting temperature (24°C) has a stronger cooling effect on the torso and mean skin temperatures than that with a higher melting temperature (28°C). Both PCM vests mitigate peak core temperature increase during the resting recovery period. The two PCM vests tested, however, had no significant effect on the alleviation of core temperature increase during exercise in the heat. To study the possibility of effective cooling of core temperature, cooling garments with PCMs at even lower melting temperatures (e.g. 15°C) and a larger covering area should be investigated.

An Adult Education Study of Participatory Community Mapping for Indigenous Knowledge Production

ERIC Educational Resources Information Center

Campbell, Craig A., Jr.

2010-01-01

This dissertation explores the notion of participatory community mapping (PCM) for Indigenous knowledge production. Three major questions were posed in the study. First, how can PCM foster Indigenous knowledge production and documentation? Second, how can PCM be used to include local voice and input in mapping projects, and third, how can adult…

PERFORMANCE EVALUATION OF A SUSTAINABLE AND ENERGY EFFICIENT RE-ROOFING TECHNOLOGY USING FIELD-TEST DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Miller, William A; Childs, Phillip W

2011-01-01

Three test attics were constructed to evaluate a new sustainable method of re-roofing utilizing photo-voltaic (PV) laminates, metal roofing panels, and PCM heat sink in the Envelope Systems Research Apparatus (ESRA) facility in the ORNL campus. Figure 1 is a picture of the three attic roofs located adjacent to each other. The leftmost roof is the conventional shingle roof, followed by the metal panel roof incorporating the cool-roof coating, and third from left is the roof with the PCM. On the PCM roof, the PV panels are seen as well; they're labelled from left-to-right as panels 5, 6 and 7.more » The metal panel roof consists of three metal panels with the cool-roof coating; in further discussion this is referred to as the infrared reflective (IRR) metal roof. The IRR metal panels reflect the incoming solar radiation and then quickly re-emit the remaining absorbed portion, thereby reducing the solar heat gain of the attic. Surface reflectance of the panels were measured using a Solar Spectrum Reflectometer. In the 0.35-2.0 {mu}m wavelength interval, which accounts for more than 94% of the solar energy, the IRR panels have an average reflectance of 0.303. In the infrared portion of the spectrum, the IRR panel reflectance is 0.633. The PCM roof consists of a layer of macro-encapsulated bio-based PCM at the bottom, followed by a 2-cm thick layer of dense fiberglass insulation with a reflective surface on top, and metal panels with pre-installed PV laminates on top. The PCM has a melting point of 29 C (84.2 F) and total enthalpy between 180 and 190 J/g. The PCM was macro-packaged in between two layers of heavy-duty plastic foil forming arrays of PCM cells. Two air cavities, between PCM cells and above the fiberglass insulation, helped the over-the-deck natural air ventilation. It is anticipated that during summer, this extra ventilation will help in reducing the attic-generated cooling loads. The extra ventilation, in conjunction with the PCM heat sink, are used to minimize thermal stresses due to the PV laminates on sunny days. In PV laminates sunlight is converted into electricity and heat simultaneous. In case of building integrated applications, a relatively high solar absorption of amorphous silicon laminates can be utilized during the winter for solar heating purposes with PCM providing necessary heat storage capacity. However, PV laminates may also generate increased building cooling loads during the summer months. Therefore, in this project, the PCM heat sink was to minimize summer heat gains as well. The PCM-fibreglass-PV assembly and the IRR metal panels are capable of being installed directly on top of existing shingle roofs during re-roofing, precluding the need for recycling or disposal of waste materials. The PV laminates installed on the PCM attic are PVL-144 models from Uni-Solar. Each laminate contains 22 triple junction amorphous silicon solar cells connected in series. The silicon cells are of dimensions 356 mm x 239 mm (14-in. x 9.4-in.). The PVL-144 laminate is encapsulated in durable ETFE (poly-ethylene-co-tetrafluoroethylene) high light-transmissive polymer. Table 1 lists the power, voltage and current ratings of the PVL-144 panel.« less

Thermal energy storage with phase change materials (PCMs) for the improvement of the energy performance of buildings

NASA Astrophysics Data System (ADS)

Soares, Nelson

The improvement of the energy efficiency of buildings during their operational phase is an active area of research. The markets are looking for new technologies, namely new thermal energy storage (TES) systems, which can be used to reduce buildings' dependency on fossil fuels, to make use of renewable energy sources and to contribute to match energy supply and demand efficiently. The main goals of this thesis are: (i) to evaluate the heat transfer with solid-liquid phase-change through small TES units filled with phase-change materials (PCMs), providing experimental data to be used in the design of new TES systems for buildings and in the validation of numerical models, and (ii) to provide some guidelines for the incorporation of PCM-drywalls in buildings aiming to reduce the energy demand for heating and cooling by making use of the latent heat from the phase-change processes of PCMs. The first part of this thesis refers to the experimental study of the heat transfer through a vertical stack of metallic rectangular cavities filled with different PCMs (a microencapsulated and a free-form PCM). The research carried out aims: (i) to analyze the melting and solidification processes of the PCM within the enclosures, (ii) to evaluate the influence of the aspect ratio of the cavities on the heat transfer and (iii) to discuss which type of PCM is better for specific cases. As a result, a big amount of experimental data for benchmarking and validation of numerical models is made available to the scientific community. Moreover, the results allow discussing which arrangement of the TES unit is better for specific applications considering the thermal regulation effect during charging, the influence of subcooling during discharging, and the influence of natural convection during both processes. It is shown that the effect of natural convection in the free-form PCM must be considered in any simulation to better describe the charging process. During discharging, subcooling must also be considered. On the contrary, the effect of natural convection and subcooling can be neglected when considering the microencapsulated PCM. The second part of this thesis concentrates on the dynamic simulation of energy in buildings considering the latent heat from PCMs' phase-change processes. The energy system under investigation is extended to an air-conditioned residential single-zone room. The main goals are: (i) to develop a holistic methodology to optimize the incorporation of PCM-drywalls in different typologies of construction and (ii) to provide guidelines for the incorporation of PCM-drywalls in different climates. Two studies are carried out: (i) a multi-dimensional optimization study combining EnergyPlus and GenOpt tools to optimize the incorporation of PCM-drywalls in lightweight steel-framed (LSF) residential buildings in Europe, and (ii) an EnergyPlus-based parametric study to optimize the incorporation of PCM-drywalls in heavyweight residential buildings in Kuwait. It is shown that an optimum PCM-drywall solution can be found for each European climate and that the incorporation of PCM-drywalls can contribute for heating and cooling energy savings in LSF construction. The results show that PCM-drywalls are particularly interesting for LSF construction in Mediterranean climates leading to higher energy savings. PCM-drywalls can also be used to reduce the annual energy demand for cooling in Kuwait by almost 5%.

Mechanical Reinforcement, Shapestabilization and Thermal Improvement of Phase-Change Energy Storage Materials Using Graphene Oxide Aerogel

NASA Astrophysics Data System (ADS)

Schuman, Yue Xu

Paraffin is known as a good energy storage phase change material (PCM) because of its high energy storage capacity and low cost. However, the leakage of liquid paraffin beyond its melting point and its low thermal conductivity hinder applications of paraffin in energy storage systems. Recently, nanomaterials have been used to create PCM composites in order to enhance their thermal properties while shape stabilizing the PCMs. However, fundamental studies on the material structures and mechanical behavior of the thermally enhanced PCM composites are limited especially at the nanoscale. In this study, we developed a PCM composite using graphene oxide aerogel (GOxA) as the reinforcing 3D network. The GOxA functions thermally as a heat transfer path and mechanically as a nanofiller to reinforce the PCM matrix. We characterized the morphology, the crystal and molecular structures as well as the multiscale mechanical and thermal behavior of the GOxA-PCM composite to evaluate the role of GOxA in the PCM composite. The molecular and diffraction characterizations imply that the GOxA network may affect the paraffin's crystallization, potentially forming an interfacial phase at the surfaces of GOxA. Furthermore, the mechanical properties were studied using nanoindentation at the nano/microscale and a digital durometer at the macroscale from 25degree C to 80 degree C. The mechanical characterizations show that the GOxA-PCM composite is 3 7x harder than pure paraffin and maintains significant strength even above paraffin's melting point due to the support from the GoxA. Moreover, the composite is much less strain-rate sensitive than paraffin. The reinforcement via GOxA is much beyond the prediction by the rule of mixture, implying a strong GOxA-paraffin interfacial bonding. Finally, a thermal scanning microscopy (SThM) along with AFM was used to study the thermal properties at microscale. AFM and thermal images indicate that GOxA-PCM has a better thermal conductivity. The latent heats and thermal conductivities were analyzed using DSC and TPS at the macroscale. Results imply that there might be an interphase between the paraffin and the GOxA resulting in a greater latent heat storage ability and better thermal conductivity of the GOxA-PCM. We believe this is the first fundamental study on the mechanical and thermal behaviors of paraffin and GOxA-PCM composite at the multiscale. The enhancement in hardness, latent heat, and thermal conductivity are expected to aid the analysis and design of thermal energy storage composites with higher performance in the future.

Sounding of the Ion Energization Region: Resolving Ambiguities

NASA Technical Reports Server (NTRS)

LaBelle, James

2003-01-01

Dartmouth College provided a single-channel high-frequency wave receiver to the Sounding of the Ion Energization Region: Resolving Ambiguities (SIERRA) rocket experiment launched from Poker Flat, Alaska, in January 2002. The receiver used signals from booms, probes, preamplifiers, and differential amplifiers provided by Cornell University coinvestigators. Output was to a dedicated 5 MHz telemetry link provided by WFF, with a small amount of additional Pulse Code Modulation (PCM) telemetry required for the receiver gain information. We also performed preliminary analysis of the data. The work completed is outlined below, in chronological order.

Optimization of Phase Change Memory with Thin Metal Inserted Layer on Material Properties

NASA Astrophysics Data System (ADS)

Harnsoongnoen, Sanchai; Sa-Ngiamsak, Chiranut; Siritaratiwat, Apirat

This works reports, for the first time, the thorough study and optimisation of Phase Change Memory (PCM) structure with thin metal inserted chalcogenide via electrical resistivity (ρ) using finite element modeling. PCM is one of the best candidates for next generation non-volatile memory. It has received much attention recently due to its fast write speed, non-destructive readout, superb scalability, and great compatibility with current silicon-based mass fabrication. The setback of PCM is a high reset current typically higher than 1mA based on 180nm lithography. To reduce the reset current and to solve the over-programming failure, PCM with thin metal inserted chalcogenide (bottom chalcogenide/metal inserted/top chalcogenide) structure has been proposed. Nevertheless, reports on optimisation of the electrical resistivity using the finite element method for this new PCM structure have never been published. This work aims to minimize the reset current of this PCM structure by optimizing the level of the electrical resistivity of the PCM profile using the finite element approach. This work clearly shows that PCM characteristics are strongly affected by the electrical resistivity. The 2-D simulation results reveal clearly that the best thermal transfer of and self-joule-heating at the bottom chalcogenide layer can be achieved under conditions; ρ_bottom chalcogenide > ρ_metal inserted > ρ_top chalcogenide More specifically, the optimized electrical resistivity of PCMTMI is attained with ρ_top chalcogenide: ρ_metal inserted: ρ_bottom chalcogenide ratio of 1:6:16 when ρ_top chalcogenide is 10-3 Ωm. In conclusion, high energy efficiency can be obtained with the reset current as low as 0.3mA and with high speed operation of less than 30ns.

Conserved TCP domain of Sas-4/CPAP is essential for pericentriolar material tethering during centrosome biogenesis

PubMed Central

Zheng, Xiangdong; Gooi, Li Ming; Wason, Arpit; Gabriel, Elke; Mehrjardi, Narges Zare; Yang, Qian; Zhang, Xingrun; Debec, Alain; Basiri, Marcus L.; Avidor-Reiss, Tomer; Pozniakovsky, Andrei; Poser, Ina; Šarić, Tomo; Hyman, Anthony A.; Li, Haitao; Gopalakrishnan, Jay

2014-01-01

Pericentriolar material (PCM) recruitment to centrioles forms a key step in centrosome biogenesis. Deregulation of this process leads to centrosome aberrations causing disorders, one of which is autosomal recessive primary microcephaly (MCPH), a neurodevelopmental disorder where brain size is reduced. During PCM recruitment, the conserved centrosomal protein Sas-4/CPAP/MCPH6, known to play a role in centriole formation, acts as a scaffold for cytoplasmic PCM complexes to bind and then tethers them to centrioles to form functional centrosomes. To understand Sas-4’s tethering role, we determined the crystal structure of its T complex protein 10 (TCP) domain displaying a solvent-exposed single-layer of β-sheets fold. This unique feature of the TCP domain suggests that it could provide an “extended surface-like” platform to tether the Sas-4–PCM scaffold to a centriole. Functional studies in Drosophila, human cells, and human induced pluripotent stem cell-derived neural progenitor cells were used to test this hypothesis, where point mutations within the 9–10th β-strands (β9–10 mutants including a MCPH-associated mutation) perturbed PCM tethering while allowing Sas-4/CPAP to scaffold cytoplasmic PCM complexes. Specifically, the Sas-4 β9–10 mutants displayed perturbed interactions with Ana2, a centrosome duplication factor, and Bld-10, a centriole microtubule-binding protein, suggesting a role for the β9–10 surface in mediating protein–protein interactions for efficient Sas-4–PCM scaffold centriole tethering. Hence, we provide possible insights into how centrosomal protein defects result in human MCPH and how Sas-4 proteins act as a vehicle to tether PCM complexes to centrioles independent of its well-known role in centriole duplication. PMID:24385583

PCM/wood composite to store thermal energy in passive building envelopes

NASA Astrophysics Data System (ADS)

Barreneche, C.; Vecstaudza, J.; Bajare, D.; Fernandez, A. I.

2017-10-01

The development of new materials to store thermal energy in a passive building system is a must to improve the thermal efficiency by thermal-regulating the indoor temperatures. This fact will deal with the reduction of the gap between energy supply and energy demand to achieve thermal comfort in building indoors. The aim of this work was to test properties of novel PCM/wood composite materials developed at Riga Technical University. Impregnation of PCM (phase change material) in wood increases its thermal mass and regulates temperature fluctuations during day and night. The PCM used are paraffin waxes (RT-21 and RT-27 from Rubitherm) and the wood used was black alder, the most common wood in Latvia. The PCM distribution inside wood sample has been studied as well as its thermophysical, mechanical and fire reaction properties. Developed composite materials are promising in the field of energy saving in buildings.

Plastic phase change material and articles made therefrom

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abhari, Ramin

The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds aremore » provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.« less

Electronic excitation of molecules in solution calculated using the symmetry-adapted cluster–configuration interaction method in the polarizable continuum model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuda, Ryoichi, E-mail: fukuda@ims.ac.jp; Ehara, Masahiro; Elements Strategy Initiative for Catalysts and Batteries

2015-12-31

The effects from solvent environment are specific to the electronic states; therefore, a computational scheme for solvent effects consistent with the electronic states is necessary to discuss electronic excitation of molecules in solution. The PCM (polarizable continuum model) SAC (symmetry-adapted cluster) and SAC-CI (configuration interaction) methods are developed for such purposes. The PCM SAC-CI adopts the state-specific (SS) solvation scheme where solvent effects are self-consistently considered for every ground and excited states. For efficient computations of many excited states, we develop a perturbative approximation for the PCM SAC-CI method, which is called corrected linear response (cLR) scheme. Our test calculationsmore » show that the cLR PCM SAC-CI is a very good approximation of the SS PCM SAC-CI method for polar and nonpolar solvents.« less

B cell-deficient mice display enhanced susceptibility to Paracoccidioides brasiliensis Infection.

PubMed

Tristão, F S M; Panagio, L A; Rocha, F A; Cavassani, K A; Moreira, A P; Rossi, M A; Silva, J S

2013-08-01

Paracoccidioidomycosis (PCM) is a chronic granulomatous disease caused by the thermally dimorphic fungus Paracoccidioides brasiliensis. T helper 1 (Th1)-mediated immunity is primarily responsible for acquired resistance during P. brasiliensis infection. On the contrary, the susceptibility is associated with occurrence of type-2 immunity (Th2), which is characterized by IL-4 release, B cell activation, and production of antibodies. Although antibodies are frequently associated with severe PCM, it is not clear whether they contribute to susceptibility or merely constitute a marker of infection stage. Here, we assessed the function of B cells during experimental P. brasiliensis infection in mice, and our results showed that B cell-knockout (B(KO)) mice are more susceptible than their wild-type littermate controls (C57BL/6, WT). The B(KO) mice showed higher mortality rate, increased number of colony-forming units in the lungs, and larger granulomas than WT mice. In the absence of B cells, we observed high levels of IL-10, whereas IFN-γ, TNF-α, and IL-4 levels were similar between both groups. Finally, we showed that transference of WT immune serum to B(KO) mice resulted in diminished infiltration of inflammatory cells and better organization of the pulmonary granulomas. Taken together, these data suggest that B cells are effectively involved in the control of P. brasiliensis growth and organization of the granulomatous lesions observed during the experimental PCM.

Phase Change Material for Temperature Control of Imager or Sounder on GOES Type Satellites in GEO

NASA Technical Reports Server (NTRS)

Choi, Michael

2013-01-01

An imager or sounder on satellites, such as the Geostationary Operational Environmental Satellite (GOES), in geostationary orbit (GEO) has a scan mirror and motor in the scan cavity. The GEO orbit is 24 hours long. During part of the orbit, direct sunlight enters the scan aperture and adds heat to components in the scan cavity. Solar heating also increases the scan motor temperature. Overheating of the scan motor could reduce its reliability. For GOES-N to P, a radiator with a thermal louver rejects the solar heat absorbed to keep the scan cavity cool. A sunshield shields the radiator/louver from the Sun. This innovation uses phase change material (PCM) in the scan cavity to maintain the temperature stability of the scan mirror and motor. When sunlight enters the scan aperture, solar heating causes the PCM to melt. When sunlight stops entering the scan aperture, the PCM releases the thermal energy stored to keep the components in the scan cavity warm. It reduces the heater power required to make up the heat lost by radiation to space through the aperture. This is a major advantage when compared to a radiator/ louver. PCM is compact because it has a high solid-to-liquid enthalpy. Also, it could be spread out in the scan cavity. This is another advantage. Paraffin wax is a good PCM candidate, with high solid-to-liquid enthalpy, which is about 225 kJ/kg. For GOES-N to P, a radiator with a louver rejects the solar heat that enters the aperture to keep the scan cavity cool. For the remainder of the orbit, sunlight does not enter the scan aperture. However, the radiator/louver continues radiating heat to space because the louver effective emittance is about 0.12, even if the louver is fully closed. This requires makeup heater power to maintain the temperature within the stability range.

Portable chlorophyll meter (PCM-502) values are related to total chlorophyll concentration and photosynthetic capacity in papaya (Carica papaya L.)

USDA-ARS?s Scientific Manuscript database

This study was carried out to verify the practical use of the portable chlorophyll meter-PCM502 (PCM) in two papaya cultivars with contrasting green coloring of the leaf blade (‘Golden’: yellowish-green; ‘Solo’: dark green). The relationship was studied between the photosynthetic process and leaf n...

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1995-12-26

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figs.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1994-12-06

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figures.

Geographical evaluation of Neuroparacoccidioidomycosis and Paracoccidioidomycosis in Southern Brazil.

PubMed

de Almeida, Sergio Monteiro; Salvador, Gabriel L O; Roza, Thiago Henrique; Izycki, Luís Felipe; Dos Santos, Isaias; Aragão, Afonso; Kulik, Amanda; Muro, Marisol; Torres, Luis Fernando Bleggi; de Noronha, Lucia Helena

2018-04-17

Paracoccidioidomycosis (PCM) is the most prevalent systemic mycosis among immunocompetent patients in Latin America. This study aimed to describe the expansion over time and the geographical distribution of confirmed Neuroparacoccidioidomycosis (NPCM) and PCM cases, and relate it to environmental characteristics such as climate, soil types, and coffee crops. This was a retrospective study of autopsy and biopsy reports between 1951 and 2014 from the Medical Pathology Section of the Hospital de Clinicas, UFPR, Curitiba, Southern Brazil. PCM was predominant in male agricultural workers. PCM cases predominated in areas with subtropical climate with hot summers in North West Parana state. NPCM cases were distributed statewide more frequent in rural than metropolitan area. There was no association with climate, soil type, or coffee crop culture. Most of the PCM cases were in the metropolitan area of the capital, chiefly due to migration fluxes. Even though the history is predominantly agricultural activities. PCM cases were distributed mainly in the metropolitan area of the state capital, there was no association with climate and soil. NPCM cases were numerically more frequent in rural than metropolitan area. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Heat transfer enhancement of PCM melting in 2D horizontal elliptical tube using metallic porous matrix

NASA Astrophysics Data System (ADS)

Jourabian, Mahmoud; Farhadi, Mousa; Rabienataj Darzi, Ahmad Ali

2016-12-01

In this study, the melting process of ice as a phase-change material (PCM) saturated with a nickel-steel porous matrix inside a horizontal elliptical tube is investigated. Due to the low thermal conductivity of the PCM, it is motivated to augment the heat transfer performance of the system simultaneously by finding an optimum value of the aspect ratio and impregnating a metallic porous matrix into the base PCM. The lattice Boltzmann method with a double distribution function formulated based on the enthalpy method, is applied at the representative elementary volume scale under the local thermal equilibrium assumption between the PCM and porous matrix in the composite. While reducing or increasing the aspect ratio of the circular tubes leads to the expedited melting, the 90° inclination of each elliptical tube in the case of the pure PCM melting does not affect the melting rate. With the reduction in the porosity, the effective thermal conductivity and melting rate in all tubes promoted. Although the natural convection is fully suppressed due to the significant flow blockage in the porous structure, the melting rates are generally increased in all cases.

Preparation and Supercooling Modification of Salt Hydrate Phase Change Materials Based on CaCl₂·2H₂O/CaCl₂.

PubMed

Xu, Xiaoxiao; Dong, Zhijun; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi

2017-06-23

Salt hydrates have issues of supercooling when they are utilized as phase change materials (PCMs). In this research, a new method was adopted to prepare a salt hydrate PCM (based on a mixture of calcium chloride dihydrate and calcium chloride anhydrous) as a novel PCM system to reduce the supercooling phenomenon existing in CaCl₂·6H₂O. Six samples with different compositions of CaCl₂ were prepared. The relationship between the performance and the proportion of calcium chloride dihydrate (CaCl₂·2H₂O) and calcium chloride anhydrous (CaCl₂) was also investigated. The supercooling degree of the final PCM reduced with the increase in volume of CaCl₂·2H₂O during its preparation. The PCM obtained with 66.21 wt % CaCl₂·2H₂O reduced the supercooling degree by about 96.8%. All six samples, whose ratio of CaCl₂·2H₂O to (CaCl₂ plus CaCl₂·2H₂O) was 0%, 34.03%, 53.82%, 76.56%, 90.74%, and 100% respectively, showed relatively higher enthalpy (greater than 155.29 J/g), and have the possibility to be applied in buildings for thermal energy storage purposes. Hence, CaCl₂·2H₂O plays an important role in reducing supercooling and it can be helpful in adjusting the solidification enthalpy. Thereafter, the influence of adding different percentages of Nano-SiO₂ (0.1 wt %, 0.3 wt %, 0.5 wt %) in reducing the supercooling degree of some PCM samples was investigated. The test results showed that the supercooling of the salt hydrate PCM in Samples 6 and 5 reduced to 0.2 °C and 0.4 °C respectively. Finally, the effect of the different cooling conditions, including frozen storage (-20 °C) and cold storage (5 °C), that were used to prepare the salt hydrate PCM was considered. It was found that both cooling conditions are effective in reducing the supercooling degree of the salt hydrate PCM. With the synergistic action of the two materials, the performance and properties of the newly developed PCM systems were better especially in terms of reducing the supercooling degree of the PCM. The novel composite PCMs are promising candidates for thermal energy storage applications.

Novel Formulations of Phase Change Materials—Epoxy Composites for Thermal Energy Storage

PubMed Central

Alvarez Feijoo, Miguel Angel

2018-01-01

This research aimed to evaluate the thermal properties of new formulations of phase change materials (PCMs)-epoxy composites, containing a thickening agent and a thermally conductive phase. The composite specimens produced consisted of composites fabricated using (a) inorganic PCMs (hydrated salts), epoxy resins and aluminum particulates or (b) organic PCM (paraffin), epoxy resins, and copper particles. Differential Scanning Calorimetry (DSC) was used to analyze the thermal behavior of the samples, while hardness measurements were used to determine changes in mechanical properties at diverse PCM and conductive phase loading values. The results indicate that the epoxy matrix can act as a container for the PCM phase without hindering the heat-absorbing behavior of the PCMs employed. Organic PCMs presented reversible phase transformations over multiple cycles, an advantage that was lacking in their inorganic counterparts. The enthalpy of the organic PCM-epoxy specimens increased linearly with the PCM content in the matrix. The use of thickening agents prevented phase segregation issues and allowed the fabrication of specimens containing up to 40% PCM, a loading significantly higher than others reported. The conductive phase seemed to improve the heat transfer and the mechanical properties of the composites when present in low percentages (<10 wt %); however, given its mass, the enthalpy detected in the composites was reduced as their loading further increased. The conductive phase combination (PCM + epoxy resin + hardener + thickening agent) presents great potential as a heat-absorbing material at the temperatures employed. PMID:29373538

Novel Formulations of Phase Change Materials-Epoxy Composites for Thermal Energy Storage.

PubMed

Arce, Maria Elena; Alvarez Feijoo, Miguel Angel; Suarez Garcia, Andres; Luhrs, Claudia C

2018-01-26

This research aimed to evaluate the thermal properties of new formulations of phase change materials (PCMs)-epoxy composites, containing a thickening agent and a thermally conductive phase. The composite specimens produced consisted of composites fabricated using (a) inorganic PCMs (hydrated salts), epoxy resins and aluminum particulates or (b) organic PCM (paraffin), epoxy resins, and copper particles. Differential Scanning Calorimetry (DSC) was used to analyze the thermal behavior of the samples, while hardness measurements were used to determine changes in mechanical properties at diverse PCM and conductive phase loading values. The results indicate that the epoxy matrix can act as a container for the PCM phase without hindering the heat-absorbing behavior of the PCMs employed. Organic PCMs presented reversible phase transformations over multiple cycles, an advantage that was lacking in their inorganic counterparts. The enthalpy of the organic PCM-epoxy specimens increased linearly with the PCM content in the matrix. The use of thickening agents prevented phase segregation issues and allowed the fabrication of specimens containing up to 40% PCM, a loading significantly higher than others reported. The conductive phase seemed to improve the heat transfer and the mechanical properties of the composites when present in low percentages (<10 wt %); however, given its mass, the enthalpy detected in the composites was reduced as their loading further increased. The conductive phase combination (PCM + epoxy resin + hardener + thickening agent) presents great potential as a heat-absorbing material at the temperatures employed.

Phase change wallboard for peak demand reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, K.L.; Shepard, M.

1993-12-31

After more than a decade of research in university and government laboratories, wallboard impregnated with a phase change material (PCM) appears to be close to commercialization, and could prove to be a powerful peak demand management tool for utilities, particularly in the residential sector. As a lightweight, easily installed thermal storage medium, PCM wallboard could be suitable for both new construction and retrofit applications. Computer simulations performed at Los Alamos National Laboratory (LANL) predicted that PCM wallboard could shift more than 90 percent of the sensible load of a residential air-conditioning system to off-peak periods, and could permit a 30more » percent reduction in equipment capacity. Residential winter peak loads could also be reduced. An Oak Ridge National Laboratory (ORNL) simulation showed that PCM wallboard could reduce peak heating demand by a third in a Tennessee climate. With more than 70 billion square feet of plasterboard produced annually in the US, widespread adoption of PCM wallboard could have a significant impact on peak load, while moderating temperature swings and enhancing comfort in homes and perhaps commercial spaces as well. Energy savings are also possible when PCM wallboard is used to take advantage of solar gain. LANL simulations predict 28 percent heating energy savings in a Boston passive solar house, and 54 percent savings in Denver. ORNL researchers support these findings -- they calculate that moving windows to the south and adding PCM wallboard could save from one-third to one-half of the heating energy needed in a Denver home.« less

Silicon waveguide optical switch with embedded phase change material.

PubMed

Miller, Kevin J; Hallman, Kent A; Haglund, Richard F; Weiss, Sharon M

2017-10-30

Phase-change materials (PCMs) have emerged as promising active elements in silicon (Si) photonic systems. In this work, we design, fabricate, and characterize a hybrid Si-PCM optical switch. By integrating vanadium dioxide (a PCM) within a Si photonic waveguide, in a non-resonant geometry, we achieve ~10 dB broadband optical contrast with a PCM length of 500 nm using thermal actuation.

Direct adaptive fuzzy control of a translating piezoelectric flexible manipulator driven by a pneumatic rodless cylinder

NASA Astrophysics Data System (ADS)

Qiu, Zhi-cheng; Wang, Bin; Zhang, Xian-min; Han, Jian-da

2013-04-01

This study presents a novel translating piezoelectric flexible manipulator driven by a rodless cylinder. Simultaneous positioning control and vibration suppression of the flexible manipulator is accomplished by using a hybrid driving scheme composed of the pneumatic cylinder and a piezoelectric actuator. Pulse code modulation (PCM) method is utilized for the cylinder. First, the system dynamics model is derived, and its standard multiple input multiple output (MIMO) state-space representation is provided. Second, a composite proportional derivative (PD) control algorithms and a direct adaptive fuzzy control method are designed for the MIMO system. Also, a time delay compensation algorithm, bandstop and low-pass filters are utilized, under consideration of the control hysteresis and the caused high-frequency modal vibration due to the long stroke of the cylinder, gas compression and nonlinear factors of the pneumatic system. The convergence of the closed loop system is analyzed. Finally, experimental apparatus is constructed and experiments are conducted. The effectiveness of the designed controllers and the hybrid driving scheme is verified through simulation and experimental comparison studies. The numerical simulation and experimental results demonstrate that the proposed system scheme of employing the pneumatic drive and piezoelectric actuator can suppress the vibration and achieve the desired positioning location simultaneously. Furthermore, the adopted adaptive fuzzy control algorithms can significantly enhance the control performance.

Neutrophils in Oral Paracoccidioidomycosis and the Involvement of Nrf2

PubMed Central

Araújo, Vera Cavalcanti; Demasi, Ana Paula Dias; Soares, Andresa Borges; Passador-Santos, Fabrício; Napimoga, Marcelo Henrique; Martinez, Elizabeth Ferreira; Freitas, Nadir Severina; Araújo, Ney Soares

2013-01-01

Neutrophils have been implicated in granuloma formation in several infectious diseases, in addition to their main phagocytic and pathogen destruction role. It has been demonstrated that Nrf2 regulates antioxidant protection in neutrophils, attenuating inflammation without compromising the hosts bacterial defense. In this study, we analyzed the presence of neutrophils in Paracoccidioides brasiliensis mycosis (PCM), as well as the immunoexpression of Nrf2. Thirty-nine cases of oral PCM were classified according to quantity of fungi and to the presence of loose or well-organized granulomas and microabscesses. An Nrf2 antibody was used for immunohistochemical analysis. The results showed that neutrophils are present in microabscesses and loose granulomas, but were absent in structured granulomas. A greater quantity of fungi was shown in cases with only loose granulomas when compared to loose and well organized granulomas. Nrf2 was observed in the nuclei of neutrophils of loose granulomas and abscesses, with its expression in loose granulomas maintained despite the additional presence of well organized granulomas in the same specimen. This study suggests that neutrophils participate in P. brasiliensis granuloma formation and that Nrf2 has a possible role in neutrophil survival, via modulation of the inflammatory response. PMID:24204715

Neutrophils in oral paracoccidioidomycosis and the involvement of Nrf2.

PubMed

Araújo, Vera Cavalcanti; Demasi, Ana Paula Dias; Soares, Andresa Borges; Passador-Santos, Fabrício; Napimoga, Marcelo Henrique; Martinez, Elizabeth Ferreira; Freitas, Nadir Severina; Araújo, Ney Soares

2013-01-01

Neutrophils have been implicated in granuloma formation in several infectious diseases, in addition to their main phagocytic and pathogen destruction role. It has been demonstrated that Nrf2 regulates antioxidant protection in neutrophils, attenuating inflammation without compromising the hosts bacterial defense. In this study, we analyzed the presence of neutrophils in Paracoccidioides brasiliensis mycosis (PCM), as well as the immunoexpression of Nrf2. Thirty-nine cases of oral PCM were classified according to quantity of fungi and to the presence of loose or well-organized granulomas and microabscesses. An Nrf2 antibody was used for immunohistochemical analysis. The results showed that neutrophils are present in microabscesses and loose granulomas, but were absent in structured granulomas. A greater quantity of fungi was shown in cases with only loose granulomas when compared to loose and well organized granulomas. Nrf2 was observed in the nuclei of neutrophils of loose granulomas and abscesses, with its expression in loose granulomas maintained despite the additional presence of well organized granulomas in the same specimen. This study suggests that neutrophils participate in P. brasiliensis granuloma formation and that Nrf2 has a possible role in neutrophil survival, via modulation of the inflammatory response.

A Computer-Aided Type-II Fuzzy Image Processing for Diagnosis of Meniscus Tear.

PubMed

Zarandi, M H Fazel; Khadangi, A; Karimi, F; Turksen, I B

2016-12-01

Meniscal tear is one of the prevalent knee disorders among young athletes and the aging population, and requires correct diagnosis and surgical intervention, if necessary. Not only the errors followed by human intervention but also the obstacles of manual meniscal tear detection highlight the need for automatic detection techniques. This paper presents a type-2 fuzzy expert system for meniscal tear diagnosis using PD magnetic resonance images (MRI). The scheme of the proposed type-2 fuzzy image processing model is composed of three distinct modules: Pre-processing, Segmentation, and Classification. λ-nhancement algorithm is used to perform the pre-processing step. For the segmentation step, first, Interval Type-2 Fuzzy C-Means (IT2FCM) is applied to the images, outputs of which are then employed by Interval Type-2 Possibilistic C-Means (IT2PCM) to perform post-processes. Second stage concludes with re-estimation of "η" value to enhance IT2PCM. Finally, a Perceptron neural network with two hidden layers is used for Classification stage. The results of the proposed type-2 expert system have been compared with a well-known segmentation algorithm, approving the superiority of the proposed system in meniscal tear recognition.

Maintaining the proper connection between the centrioles and the pericentriolar matrix requires Drosophila centrosomin.

PubMed

Lucas, Eliana P; Raff, Jordan W

2007-08-27

Centrosomes consist of two centrioles surrounded by an amorphous pericentriolar matrix (PCM), but it is unknown how centrioles and PCM are connected. We show that the centrioles in Drosophila embryos that lack the centrosomal protein Centrosomin (Cnn) can recruit PCM components but cannot maintain a proper attachment to the PCM. As a result, the centrioles "rocket" around in the embryo and often lose their connection to the nucleus in interphase and to the spindle poles in mitosis. This leads to severe mitotic defects in embryos and to errors in centriole segregation in somatic cells. The Cnn-related protein CDK5RAP2 is linked to microcephaly in humans, but cnn mutant brains are of normal size, and we observe only subtle defects in the asymmetric divisions of mutant neuroblasts. We conclude that Cnn maintains the proper connection between the centrioles and the PCM; this connection is required for accurate centriole segregation in somatic cells but is not essential for the asymmetric division of neuroblasts.

Continued Water-Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Hansen, Scott; Poynot, Joe

2014-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full-scale, Orion sized water-based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research and experimentation to the full scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Design and construction of these HX's led to successful testing of both PCM HX's.

Design and Preparation of Carbon Based Composite Phase Change Material for Energy Piles.

PubMed

Yang, Haibin; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi; Li, Dongxu

2017-04-07

Energy piles-A fairly new renewable energy concept-Use a ground heat exchanger (GHE) in the foundation piles to supply heating and cooling loads to the supported building. Applying phase change materials (PCMs) to piles can help in maintaining a stable temperature within the piles and can then influence the axial load acting on the piles. In this study, two kinds of carbon-based composite PCMs (expanded graphite-based PCM and graphite nanoplatelet-based PCM) were prepared by vacuum impregnation for potential application in energy piles. Thereafter, a systematic study was performed and different characterization tests were carried out on two composite PCMs. The composite PCMs retained up to 93.1% of paraffin and were chemically compatible, thermally stable and reliable. The latent heat of the composite PCM was up to 152.8 J/g while the compressive strength of cement paste containing 10 wt % GNP-PCM was found to be 37 MPa. Hence, the developed composite PCM has potential for thermal energy storage applications.

Study of signal-to-noise ratio in digital mammography

NASA Astrophysics Data System (ADS)

Kato, Yuri; Fujita, Naotoshi; Kodera, Yoshie

2009-02-01

Mammography techniques have recently advanced from those using analog systems (the screen-film system) to those using digital systems; for example, computed radiography (CR) and flat-panel detectors (FPDs) are nowadays used in mammography. Further, phase contrast mammography (PCM)-a digital technique by which images with a magnification of 1.75× can be obtained-is now available in the market. We studied the effect of the air gap in PCM and evaluated the effectiveness of an antiscatter x-ray grid in conventional mammography (CM) by measuring the scatter fraction ratio (SFR) and relative signal-to-noise ratio (rSNR) and comparing them between PCM and the digital CM. The results indicated that the SFRs for the CM images obtained with a grid were the lowest and that these ratios were almost the same as those for the PCM images. In contrast, the rSNRs for the PCM images were the highest, which means that the scattering of x-rays was sufficiently reduced by the air gap without the loss of primary x-rays.

Resistive switching characteristics of interfacial phase-change memory at elevated temperature

NASA Astrophysics Data System (ADS)

Mitrofanov, Kirill V.; Saito, Yuta; Miyata, Noriyuki; Fons, Paul; Kolobov, Alexander V.; Tominaga, Junji

2018-04-01

Interfacial phase-change memory (iPCM) devices were fabricated using W and TiN for the bottom and top contacts, respectively, and the effect of operation temperature on the resistive switching was examined over the range between room temperature and 200 °C. It was found that the high-resistance (RESET) state in an iPCM device drops sharply at around 150 °C to a low-resistance (SET) state, which differs by ˜400 Ω from the SET state obtained by electric-field-induced switching. The iPCM device SET state resistance recovered during the cooling process and remained at nearly the same value for the RESET state. These resistance characteristics greatly differ from those of the conventional Ge-Sb-Te (GST) alloy phase-change memory device, underscoring the fundamentally different switching nature of iPCM devices. From the thermal stability measurements of iPCM devices, their optimal temperature operation was concluded to be less than 100 °C.

Design and Preparation of Carbon Based Composite Phase Change Material for Energy Piles

PubMed Central

Yang, Haibin; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi; Li, Dongxu

2017-01-01

Energy piles—A fairly new renewable energy concept—Use a ground heat exchanger (GHE) in the foundation piles to supply heating and cooling loads to the supported building. Applying phase change materials (PCMs) to piles can help in maintaining a stable temperature within the piles and can then influence the axial load acting on the piles. In this study, two kinds of carbon-based composite PCMs (expanded graphite-based PCM and graphite nanoplatelet-based PCM) were prepared by vacuum impregnation for potential application in energy piles. Thereafter, a systematic study was performed and different characterization tests were carried out on two composite PCMs. The composite PCMs retained up to 93.1% of paraffin and were chemically compatible, thermally stable and reliable. The latent heat of the composite PCM was up to 152.8 J/g while the compressive strength of cement paste containing 10 wt % GNP-PCM was found to be 37 MPa. Hence, the developed composite PCM has potential for thermal energy storage applications. PMID:28772752

Identification of Metabolism and Excretion Differences of Procymidone between Rats and Humans Using Chimeric Mice: Implications for Differential Developmental Toxicity.

PubMed

Abe, Jun; Tomigahara, Yoshitaka; Tarui, Hirokazu; Omori, Rie; Kawamura, Satoshi

2018-02-28

A metabolite of procymidone, hydroxylated-PCM, causes rat-specific developmental toxicity due to higher exposure to it in rats than in rabbits or monkeys. When procymidone was administered to chimeric mice with rat or human hepatocytes, the plasma level of hydroxylated-PCM was higher than that of procymidone in rat chimeric mice, and the metabolic profile of procymidone in intact rats was well reproduced in rat chimeric mice. In human chimeric mice, the plasma level of hydroxylated-PCM was less, resulting in a much lower exposure. The main excretion route of hydroxylated-PCM-glucuronide was bile (the point that hydroxylated-PCM enters the enterohepatic circulation) in rat chimeric mice, and urine in human chimeric mice. These data suggest that humans, in contrast to rats, extensively form the glucuronide and excrete it in urine, as do rabbits and monkeys. Overall, procymidone's potential for causing teratogenicity in humans must be low compared to that in rats.

A wideband-PCM recorder for the Space Shuttle orbiter

NASA Technical Reports Server (NTRS)

Petit, R. D.

1976-01-01

The Shuttle wideband-PCM recorder accomplishes recording on up to 14 data tracks with analog or digital data inputs. FM multiplexed analog frequencies of up to 2 MHz and digital rates of 1 Mb/s are accommodated at a tape speed of 120 in/s. Recording time in analog mode varies between 4 min for 2 MHz data to 80 min for 100 kHz data. The total digital data storage is 3.44 x 10 to the 9th bits with recording times from 1 hour for 1 Mb/s to 19 hours for 50 Kb/s data in the serial track switching mode. A versatile command decoder and control interface are used for eight primary modes of operation.

A multichannel EEG telemetry system utilizing a PCM subcarrier

NASA Technical Reports Server (NTRS)

Fryer, T. B.

1974-01-01

A multichannel personal-type telemetry system is described that utilizes PCM encoding for the most effective range with minimum RF bandwidth and noise interference. Recent IC developments (COS MOS) make it possible to implement a sophisticated encoding system (PCM) within the low power and size constraints necessary for a personal biotelemetry system. This system includes low-level high-impedance preamplifiers to make the system suitable for EEG recording.

Compressive and flexural strength of high strength phase change mortar

NASA Astrophysics Data System (ADS)

Qiao, Qingyao; Fang, Changle

2018-04-01

High-strength cement produces a lot of hydration heat when hydrated, it will usually lead to thermal cracks. Phase change materials (PCM) are very potential thermal storage materials. Utilize PCM can help reduce the hydration heat. Research shows that apply suitable amount of PCM has a significant effect on improving the compressive strength of cement mortar, and can also improve the flexural strength to some extent.

The effectiveness of organic PCM based on lauric acid from coconut oil and inorganic PCM based on salt hydrate CaCl2.6H2o as latent heat energy storage system in Indonesia

NASA Astrophysics Data System (ADS)

U, Sri Rahayu A.; Putri, Widya A.; Sutjahja, I. M.; Kurnia, D.; Wonorahardjo, S.

2016-08-01

A latent heat energy storage system utilizing phase change materials (PCM) is an alternative strategy to reduce the use of Air Conditioning (AC) system in big cities in Indonesia in order for energy conservation in the future. In this research we used two kinds of materials, namely organic PCM based on lauric acid from coconut oil (CO) and inorganic PCM based on salt hydrate CaCl2.6H2O, because they have thermophysical parameters suitable for human's thermal comfort application in the building. The CO which contained more than 50% lauric acid has the melting temperature (Tm ) of about 26 °C and heat entalphy (ΔH) around 103 kJ/kg, while CaCl2.6H2O has the melting point of 29 °C and heat entalphy of 190 kJ/kg. In this paper we report the effectiveness of those two kinds of PCM in reducing the air temperature as one of some criteria for human's thermal comfort. The experiments were performed in a close and adiabatic room and the time-temperature measurements were done automatically using Arduino microcontroller and LM35 temperature sensor connected to the PC.

Reactivity Coefficient Calculation for AP1000 Reactor Using the NODAL3 Code

NASA Astrophysics Data System (ADS)

Pinem, Surian; Malem Sembiring, Tagor; Tukiran; Deswandri; Sunaryo, Geni Rina

2018-02-01

The reactivity coefficient is a very important parameter for inherent safety and stability of nuclear reactors operation. To provide the safety analysis of the reactor, the calculation of changes in reactivity caused by temperature is necessary because it is related to the reactor operation. In this paper, the temperature reactivity coefficients of fuel and moderator of the AP1000 core are calculated, as well as the moderator density and boron concentration. All of these coefficients are calculated at the hot full power condition (HFP). All neutron diffusion constant as a function of temperature, water density and boron concentration were generated by the SRAC2006 code. The core calculations for determination of the reactivity coefficient parameter are done by using NODAL3 code. The calculation results show that the fuel temperature, moderator temperature and boron reactivity coefficients are in the range between -2.613 pcm/°C to -4.657pcm/°C, -1.00518 pcm/°C to 1.00649 pcm/°C and -9.11361 pcm/ppm to -8.0751 pcm/ppm, respectively. For the water density reactivity coefficients, the positive reactivity occurs at the water temperature less than 190 °C. The calculation results show that the reactivity coefficients are accurate because the results have a very good agreement with the design value.

Towards a drift-free multi-level Phase Change Memory

NASA Astrophysics Data System (ADS)

Cinar, Ibrahim; Ozdemir, Servet; Cogulu, Egecan; Gokce, Aisha; Stipe, Barry; Katine, Jordan; Aktas, Gulen; Ozatay, Ozhan

For ultra-high density data storage applications, Phase Change Memory (PCM) is considered a potentially disruptive technology. Yet, the long-term reliability of the logic levels corresponding to the resistance states of a PCM device is an important issue for a stable device operation since the resistance levels drift uncontrollably in time. The underlying mechanism for the resistance drift is considered as the structural relaxation and spontaneous crystallization at elevated temperatures. We fabricated a nanoscale single active layer-phase change memory cell with three resistance levels corresponding to crystalline, amorphous and intermediate states by controlling the current injection site geometry. For the intermediate state and the reset state, the activation energies and the trap distances have been found to be 0.021 eV and 0.235 eV, 1.31 nm and 7.56 nm, respectively. We attribute the ultra-low and weakly temperature dependent drift coefficient of the intermediate state (ν = 0.0016) as opposed to that of the reset state (ν = 0.077) as being due to the dominant contribution of the interfacial defects in electrical transport in the case of the mixed phase. Our results indicate that the engineering of interfacial defects will enable a drift-free multi-level PCM device design.

Heat transfer and thermal management of electric vehicle batteries with phase change materials

NASA Astrophysics Data System (ADS)

Ramandi, M. Y.; Dincer, I.; Naterer, G. F.

2011-07-01

This paper examines a passive thermal management system for electric vehicle batteries, consisting of encapsulated phase change material (PCM) which melts during a process to absorb the heat generated by a battery. A new configuration for the thermal management system, using double series PCM shells, is analyzed with finite volume simulations. A combination of computational fluid dynamics (CFD) and second law analysis is used to evaluate and compare the new system against the single PCM shells. Using a finite volume method, heat transfer in the battery pack is examined and the results are used to analyse the exergy losses. The simulations provide design guidelines for the thermal management system to minimize the size and cost of the system. The thermal conductivity and melting temperature are studied as two important parameters in the configuration of the shells. Heat transfer from the surroundings to the PCM shell in a non-insulated case is found to be infeasible. For a single PCM system, the exergy efficiency is below 50%. For the second case for other combinations, the exergy efficiencies ranged from 30-40%. The second shell content did not have significant influence on the exergy efficiencies. The double PCM shell system showed higher exergy efficiencies than the single PCM shell system (except a case for type PCM-1). With respect to the reference environment, it is found that in all cases the exergy efficiencies decreased, when the dead-state temperatures rises, and the destroyed exergy content increases gradually. For the double shell systems for all dead-state temperatures, the efficiencies were very similar. Except for a dead-state temperature of 302 K, with the other temperatures, the exergy efficiencies for different combinations are well over 50%. The range of exergy efficiencies vary widely between 15 and 85% for a single shell system, and between 30-80% for double shell systems.

Sb-Te Phase-change Materials under Nanoscale Confinement

NASA Astrophysics Data System (ADS)

Ihalawela, Chandrasiri A.

Size, speed and efficiency are the major challenges of next generation nonvolatile memory (NVM), and phase-change memory (PCM) has captured a great attention due to its promising features. The key for PCM is rapid and reversible switching between amorphous and crystalline phases with optical or electrical excitation. The structural transition is associated with significant contrast in material properties which can be utilized in optical (CD, DVD, BD) and electronic (PCRAM) memory applications. Importantly, both the functionality and the success of PCM technology significantly depend on the core material and its properties. So investigating PC materials is crucial for the development of PCM technology to realized enhanced solutions. In regards to PC materials, Sb-Te binary plays a significant role as a basis to the well-known Ge-Sb-Te system. Unlike the conventional deposition methods (sputtering, evaporation), electrochemical deposition method is used due to its multiple advantages, such as conformality, via filling capability, etc. First, the controllable synthesis of Sb-Te thin films was studied for a wide range of compositions using this novel deposition method. Secondly, the solid electrolytic nature of stoichiometric Sb2Te3 was studied with respect to precious metals. With the understanding of 2D thin film synthesis, Sb-Te 1D nanowires (18 - 220 nm) were synthesized using templated electrodeposition, where nanoporous anodic aluminum oxide (AAO) was used as a template for the growth of nanowires. In order to gain the controllability over the deposition in high aspect ratio structures, growth mechanisms of both the thin films and nanowires were investigated. Systematic understanding gained thorough previous studies helped to formulate the ultimate goal of this dissertation. In this dissertation, the main objective is to understand the size effect of PC materials on their phase transition properties. The reduction of effective memory cell size in conjunction with multilevel cells could be promising to achieve high data densities. However the size reduction may result in changes in material properties. If phase transition properties of the materials are also tunable with respect to the size, then more attractive solutions could be realized. So we have reported the size effect on crystallization temperature of prototypical Sb2Te3 nanowires synthesized in AAO templates. Moreover, we have found that the reduction of nanowire size can elevate the crystallization temperature, which is crucial for data retention in PCM technology. Energy dispersive X-ray spectroscopy, X-ray diffraction, electron microscopy and electrical resistivity measurements were used to characterize the composition, structure, morphology, and phase transition properties of the materials. We believe that this dissertation will provide new insights into the size effect of PC materials in addition to the controllable synthesis of PC thin films and nanowires through the novel electrochemical method.

Comparison of radiologist performance with photon-counting full-field digital mammography to conventional full-field digital mammography.

PubMed

Cole, Elodia B; Toledano, Alicia Y; Lundqvist, Mats; Pisano, Etta D

2012-08-01

The purpose of this study was to assess the performance of a MicroDose photon-counting full-field digital mammography (PCM) system in comparison to full-field digital mammography (FFDM) for area under the receiver-operating characteristic (ROC) curve (AUC), sensitivity, specificity, and feature analysis of standard-view mammography for women presenting for screening mammography, diagnostic mammography, or breast biopsy. A total of 133 women were enrolled in this study at two European medical centers, with 67 women who had a pre-existing 10-36 months FFDM enrolled prospectively into the study and 66 women who underwent breast biopsy and had screening PCM and diagnostic FFDM, including standard craniocaudal and mediolateral oblique views of the breast with the lesion, enrolled retrospectively. The case mix consisted of 49 cancers, 17 biopsy-benign cases, and 67 normal cases. Sixteen radiologists participated in the reader study and interpreted all 133 cases in both conditions, separated by washout period of ≥4 weeks. ROC curve and free-response ROC curve analyses were performed for noninferiority of PCM compared to FFDM using a noninferiority margin Δ value of 0.10. Feature analysis of the 66 cases with lesions was conducted with all 16 readers at the conclusion of the blinded reads. Mean glandular dose was recorded for all cases. The AUC for PCM was 0.947 (95% confidence interval [CI], 0.920-0.974) and for FFDM was 0.931 (95% CI, 0.898-0.964). Sensitivity per case for PCM was 0.936 (95% CI, 0.897-0.976) and for FFDM was 0.908 (95% CI, 0.856-0.960). Specificity per case for PCM was 0.764 (95% CI, 0.688-0.841) and for FFDM was 0.749 (95% CI, 0.668-0.830). Free-response ROC curve figures of merit were 0.920 (95% CI, 0.881-0.959) and 0.903 (95% CI, 0.858-0.948) for PCM and FFDM, respectively. Sensitivity per lesion was 0.903 (95% CI, 0.846-0.960) and 0.883 (95% CI, 0.823-0.944) for PCM and FFDM, respectively. The average false-positive marks per image of noncancer cases were 0.265 (95% CI, 0.171-0.359) and 0.281 (95% CI, 0.188-0.374) for PCM and FFDM, respectively. Noninferiority P values for AUC, sensitivity (per case and per lesion), specificity, and average false-positive marks per image were all statistically significant (P < .001). The noninferiority P value for free-response ROC was <.025, from the 95% CI for the difference. Feature analysis resulted in PCM being preferred to FFDM by the readers for ≥70% of the cases. The average mean glandular dose for PCM was 0.74 mGy (95% CI, 0.722-0.759 mGy) and for FFDM was 1.23 mGy (95% CI, 1.199-1.262 mGy). In this study, radiologist performance with PCM was not inferior to that with conventional FFDM at an average 40% lower mean glandular dose. Copyright © 2012 AUR. Published by Elsevier Inc. All rights reserved.

Comprehensive, Individualized, Person-Centered Management of Community-Residing Persons with Moderate-to-Severe Alzheimer Disease: A Randomized Controlled Trial.

PubMed

Reisberg, Barry; Shao, Yongzhao; Golomb, James; Monteiro, Isabel; Torossian, Carol; Boksay, Istvan; Shulman, Melanie; Heller, Sloane; Zhu, Zhaoyin; Atif, Ayesha; Sidhu, Jaskirat; Vedvyas, Alok; Kenowsky, Sunnie

2017-01-01

The aim was to examine added benefits of a Comprehensive, Individualized, Person-Centered Management (CI-PCM) program to memantine treatment. This was a 28-week, clinician-blinded, randomized, controlled, parallel-group study, with a similar study population, similar eligibility criteria, and a similar design to the memantine pivotal trial of Reisberg et al. [N Engl J Med 2003;348:1333-1341]. Twenty eligible community-residing Alzheimer disease (AD) subject-caregiver dyads were randomized to the CI-PCM program (n = 10) or to usual community care (n = 10). Primary outcomes were the New York University Clinician's Interview-Based Impression of Change Plus Caregiver Input (NYU-CIBIC-Plus), assessed by one clinician set, and an activities of daily living inventory, assessed by a separate clinician set at baseline and at weeks 4, 12, and 28. Primary outcomes showed significant benefits of the CI-PCM program at all post-baseline evaluations. Improvement on the NYU-CIBIC-Plus in the management group at 28 weeks was 2.9 points over the comparator group. The memantine 2003 trial showed an improvement of 0.3 points on this global measure in memantine-treated versus placebo-randomized subjects at 28 weeks. Hence, globally, the management program intervention benefits were 967% greater than memantine treatment alone. These results are approximately 10 times those usually observed with both nonpharmacological and pharmacological treatments and indicate substantial benefits with the management program for advanced AD persons. © 2017 S. Karger AG, Basel.

Point charge representation of multicenter multipole moments in calculation of electrostatic properties

NASA Technical Reports Server (NTRS)

Sokalski, W. A.; Shibata, M.; Ornstein, R. L.; Rein, R.

1993-01-01

Distributed Point Charge Models (PCM) for CO, (H2O)2, and HS-SH molecules have been computed from analytical expressions using multi-center multipole moments. The point charges (set of charges including both atomic and non-atomic positions) exactly reproduce both molecular and segmental multipole moments, thus constituting an accurate representation of the local anisotropy of electrostatic properties. In contrast to other known point charge models, PCM can be used to calculate not only intermolecular, but also intramolecular interactions. Comparison of these results with more accurate calculations demonstrated that PCM can correctly represent both weak and strong (intramolecular) interactions, thus indicating the merit of extending PCM to obtain improved potentials for molecular mechanics and molecular dynamics computational methods.

Satellite thermal storage systems using metallic phase-change materials

NASA Astrophysics Data System (ADS)

Lauf, R. J.; Hamby, C.

Solar (thermal) dynamic power systems for satellites require a heat storage system capable of operating the engine during eclipse. A system is described in which the phase-change material (PCM) is a metal rather than the more conventional fluoride salts. Thermal storage modules consisting of germanium contained in graphite have good thermal conductivity, low parasitic mass, and are physically and chemically stable. The result is described for thermal cycle testing of graphite capsules containing germanium and several germanium- and silicon-based alloys, as well as some initial tests of the compatibility of graphite with Nb-1 percent Zr structural materials.

Volumetric changes and clinical outcome for petroclival meningiomas after primary treatment with Gamma Knife radiosurgery.

PubMed

Sadik, Zjiwar H A; Lie, Suan Te; Leenstra, Sieger; Hanssens, Patrick E J

2018-01-26

OBJECTIVE Petroclival meningiomas (PCMs) can cause devastating clinical symptoms due to mass effect on cranial nerves (CNs); thus, patients harboring these tumors need treatment. Many neurosurgeons advocate for microsurgery because removal of the tumor can provide relief or result in symptom disappearance. Gamma Knife radiosurgery (GKRS) is often an alternative for surgery because it can cause tumor shrinkage with improvement of symptoms. This study evaluates qualitative volumetric changes of PCM after primary GKRS and its impact on clinical symptoms. METHODS The authors performed a retrospective study of patients with PCM who underwent primary GKRS between 2003 and 2015 at the Gamma Knife Center of the Elisabeth-Tweesteden Hospital in Tilburg, the Netherlands. This study yields 53 patients. In this study the authors concentrate on qualitative volumetric tumor changes, local tumor control rate, and the effect of the treatment on trigeminal neuralgia (TN). RESULTS Local tumor control was 98% at 5 years and 93% at 7 years (Kaplan-Meier estimates). More than 90% of the tumors showed regression in volume during the first 5 years. The mean volumetric tumor decrease was 21.2%, 27.1%, and 31% at 1, 3, and 6 years of follow-up, respectively. Improvement in TN was achieved in 61%, 67%, and 70% of the cases at 1, 2, and 3 years of follow-up, respectively. This was associated with a mean volumetric tumor decrease of 25% at the 1-year follow-up to 32% at the 3-year follow-up. CONCLUSIONS GKRS for PCMs yields a high tumor control rate with a low incidence of neurological deficits. Many patients with TN due to PCM experienced improvement in TN after radiosurgery. GKRS achieves significant volumetric tumor decrease in the first years of follow-up and thereafter.

Improved OTEC System for a Submarine Robot

NASA Technical Reports Server (NTRS)

Chao, Yi; Jones, Jack; Valdez, Thomas

2010-01-01

An ocean thermal energy conversion (OTEC), now undergoing development, is a less-massive, more-efficient means of exploiting the same basic principle as that of the proposed system described in "Alternative OTEC Scheme for a Submarine Robot" (NPO-43500), NASA Tech Briefs, Vol. 33, No. 1 (January 2009), page 50. The proposed system as described previously would be based on the thawing-expansion/freezing-contraction behavior of a wax or perhaps another suitable phase-change material (PCM). The power generated by the system would be used to recharge the batteries in a battery- powered unmanned underwater vehicle [UUV (essentially, a small exploratory submarine robot)] of a type that has been deployed in large numbers in research pertaining to global warming. A UUV of this type travels between the ocean surface and depths, measuring temperature and salinity. At one phase of its operational cycle, the previously proposed system would utilize the surface ocean temperature (which lies between 15 and 30 C over most of the Earth) to melt a PCM that has a melting/freezing temperature of about 10 C. At the opposite phase of its operational cycle, the system would utilize the lower ocean temperature at depth (e.g., between 4 and 7 C at a depth of 300 m) to freeze the PCM. The melting or freezing would cause the PCM to expand or contract, respectively, by about 9 volume percent. The PCM would be contained in tubes that would be capable of expanding and contracting with the PCM. The PCM-containing tubes would be immersed in a hydraulic fluid. The expansion and contraction would drive a flow of the hydraulic fluid against a piston that, in turn, would push a rack-and-pinion gear system to spin a generator to charge a battery.

A Study on a Novel Phase Change Material Panel Based on Tetradecanol/Lauric Acid/Expanded Perlite/Aluminium Powder for Building Heat Storage

PubMed Central

Wang, Enyu; Kong, Xiangfei; Rong, Xian; Yao, Chengqiang; Yang, Hua; Qi, Chengying

2016-01-01

Phase change material (PCM) used in buildings can reduce the building energy consumption and indoor temperature fluctuation. A composite PCM has been fabricated by the binary eutectic mixture of tetradecanol (TD) and lauric acid (LA) absorbed into the expanded perlite (EP) using vacuum impregnation method, and its thermal conductivity was promoted by aluminium powder (AP) additive. Besides, the styrene-acrylic emulsion has been mixed with the composite PCM particles to form the protective film, so as to solve the problem of leakage. Thus, a novel PCM panel (PCMP) has been prepared using compression moulding forming method. The thermal property, microstructure characteristic, mechanical property, thermal conductivity, thermal reliability and leakage of the composite PCM have been investigated and analysed. Meanwhile, the thermal performance of the prepared PCMP was tested through PCMPs installed on the inside wall of a cell under outdoor climatic conditions. The composite PCM has a melting temperature of 24.9 °C, a freezing temperature of 25.2 °C, a melting latent heat of 78.2 J/g and a freezing latent heat of 81.3 J/g. The thermal conductivity test exposed that the thermal conductivity has been enhanced with the addition of AP and the latent heat has been decreased, but it still remains in a high level. The leakage test result has proven that liquid PCM leaking has been avoided by the surface film method. The thermal performance experiment has shown the significant function of PCMP about adjusting the indoor temperature and reducing the heats transferring between the wall inside and outside. In view of the thermal performance, mechanical property and thermal reliability results, it can be concluded that the prepared PCMP has a promising building application potential. PMID:28774020

A non-volatile flip-flop based on diode-selected PCM for ultra-low power systems

NASA Astrophysics Data System (ADS)

Ye, Yong; Du, Yuan; Gao, Dan; Kang, Yong; Song, Zhitang; Chen, Bomy

2016-10-01

As the process technology is continuously shrinking, low power consumption is a major issue in VLSI Systems-on-Chip (SoCs), especially for standby-power-critical applications. Recently, the emerging CMOS-compatible non-volatile memories (NVMs), such as Phase Change Memory (PCM), have been used as on-chip storage elements, which can obtain non-volatile processing, nearly-zero standby power and instant-on capability. PCM has been considered as the best candidate for the next generation of NVMs for its low cost, high density and high resistance transformation ratio. In this paper, for the first time, we present a diode-selected PCM based non-volatile flip-flop (NVFF) which is optimized for better power consumption and process variation tolerance. With dual trench isolation process, the diode-selected PCM realizes ultra small area, which is very suitable for multi-context configuration and large scale flip-flops matrix. Since the MOS-selected PCM is hard to shrink further due to large amount of PCM write current, the proposed NVFF achieves higher power efficiency without loss of current driving capability. Using the 40nm manufacturing process, the area of the cell (1D1R) is as small as 0.016 μm2. Simulation results show that the energy consumption during the recall operation is 62 fJ with 1.1 standard supply voltage, which is reduced by 54.9% compared to the previous 2T2R based NVFF. When the supply voltage reduces to 0.7 V, the recall energy is as low as 17 fJ. With the great advantages in cell size and energy, the proposed diode-selected NVFF is very applicable and cost-effective for ULP systems.

Correlating Computed Tomography Perfusion Changes in the Pharyngeal Constrictor Muscles During Head-and-Neck Radiotherapy to Dysphagia Outcome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Truong, Minh Tam, E-mail: mitruong@bu.edu; Department of Radiology, Boston Medical Center and Boston University School of Medicine, Boston, MA; Lee, Richard

2012-02-01

Purpose: To measure changes in perfusion of the pharyngeal constrictor muscles (PCM) using CT perfusion (CTP) imaging during a course of definitive radiotherapy (RT) in head-and-neck cancer (HNC) patients and correlate with dysphagia outcome after RT. Methods and Materials: Fifteen HNC patients underwent CTP imaging of the PCM at baseline and Weeks 2, 4, and 6 during RT and 6 weeks after RT. Blood flow and blood volume were measured in the PCM, and percentage change from baseline scan was determined. A single physician-based assessment of dysphagia was performed every 3 months after RT using the Common Terminology Criteria formore » Adverse Events, version 3.0 grading system. Results: With a median follow-up of 28 months (range, 6-44 months), Grade 3 dysphagia was present in 7 of 15 patients, and 8 patients experienced Grade 0-2 dysphagia. The CTP parameters at Week 2 of RT demonstrated an increase in mean PCM blood flow of 161.9% vs. 12.3% (p = 0.007) and an increase in mean PCM blood volume of 96.6% vs. 8.7% (p = 0.039) in patients with 6-month post-RT Grade 3 dysphagia and Grade 0-2 dysphagia, respectively. On multivariate analysis, when adjusting for smoking history, tumor volume, and baseline dysphagia status, an increase in blood flow in the second week of RT was significant for 3- and 6-month Grade 3 dysphagia (p < 0.05). Conclusions: Perfusion changes in the PCM during Week 2 of RT in the PCM may predict the severity of dysphagia after HNC RT.« less

Estimating Energy Expenditure Using Heat Flux Measured at Single Body Site

PubMed Central

Lyden, Kate; Swibas, Tracy; Catenacci, Victoria; Guo, Ruixin; Szuminsky, Neil; Melanson, Edward L.

2014-01-01

Introduction The Personal Calorie Monitor (PCM) is a portable direct calorimeter that estimates energy expenditure (EE) from measured heat flux (i.e. the sum of conductive, convective, radiative, and evaporative). Purpose The primary aim of this study was to compare EE estimated from measures of heat flux to indirect calorimetry in a thermoneutral environment (26°C). A secondary aim was to determine if exposure to ambient temperature below thermoneutral (19°C) influences the accuracy of the PCM. Methods 34 Adults (mean±SD, age = 28±5 y, body mass index = 22.9±2.6 kg.m2) were studied for 5 h in a whole-room indirect calorimeter (IC) in thermoneutral and cool conditions. Participants wore the PCM on their upper arm and completed two, 20-minute treadmill-walking bouts (0% grade, 3 mph). The remaining time was spent sedentary (e.g., watching television, using a computer). Results In thermoneutral, EE (mean (95% CI)) measured by IC and PCM was 560.0 (526.5, 593.5) and 623.3 (535.5, 711.1) kcals, respectively. In cool, EE measured by IC and PCM was 572.5 (540.9, 604.0) and 745.5 (668.1, 822.8) kcals, respectively. Under thermoneutral conditions, mean PCM minute-by-minute EE tracked closely with IC, resulting in a small, non-significant bias (63 kcals (−5.8, 132.4)). During cool conditions, mean PCM minute-by-minute EE did not track IC, resulting in a large bias (173.0 (93.9, 252.1)) (p<0.001). Conclusion This study demonstrated the validity of using measured heat flux to estimate EE. However, accuracy may be impaired in cool conditions, possibly due to excess heat loss from the exposed limbs. PMID:24811326

Heat transfer characteristics of coconut oil as phase change material to room cooling application

NASA Astrophysics Data System (ADS)

Irsyad, M.; Harmen

2017-03-01

Thermal comfort in a room is one of human needs in the workplace and dwellings, so that the use of air conditioning system in tropical countries is inevitable. This equipment has an impact on the increase of energy consumption. One method of minimizing the energy use is by using the phase change material (PCM) as thermal energy storage. This material utilizes the temperature difference between day and night for the storage and release of thermal energy. PCM development on application as a material for air cooling inlet, partitioning and interior needs to be supported by the study of heat transfer characteristics when PCM absorbs heat from ambient temperature. This study was conducted to determine the heat transfer characteristics on coconut oil as a phase change material. There are three models of experiments performed in this research. Firstly, an experiment was conducted to analyze the time that was needed by material to phase change by varying the temperature. The second experiment analyzed the heat transfer characteristics of air to PCM naturally convection. The third experiment analyzed the forced convection heat transfer on the surface of the PCM container by varying the air velocity. The data of experimental showed that, increasing ambient air temperature resulted in shorter time for phase change. At temperatures of 30°C, the time for phase change of PCM with the thickness of 8 cm was 1700 min, and it was stable at temperatures of 27°C. Increasing air temperature accelerated the phase change in the material. While for the forced convection heat transfer, PCM could reduce the air temperature in the range of 30 to 35°C at about 1 to 2°C, with a velocity of 1-3 m/s.

Electronic excitation spectra of molecules in solution calculated using the symmetry-adapted cluster-configuration interaction method in the polarizable continuum model with perturbative approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuda, Ryoichi, E-mail: fukuda@ims.ac.jp; Ehara, Masahiro; Elements Strategy Initiative for Catalysts and Batteries

A perturbative approximation of the state specific polarizable continuum model (PCM) symmetry-adapted cluster-configuration interaction (SAC-CI) method is proposed for efficient calculations of the electronic excitations and absorption spectra of molecules in solutions. This first-order PCM SAC-CI method considers the solvent effects on the energies of excited states up to the first-order with using the zeroth-order wavefunctions. This method can avoid the costly iterative procedure of the self-consistent reaction field calculations. The first-order PCM SAC-CI calculations well reproduce the results obtained by the iterative method for various types of excitations of molecules in polar and nonpolar solvents. The first-order contribution ismore » significant for the excitation energies. The results obtained by the zeroth-order PCM SAC-CI, which considers the fixed ground-state reaction field for the excited-state calculations, are deviated from the results by the iterative method about 0.1 eV, and the zeroth-order PCM SAC-CI cannot predict even the direction of solvent shifts in n-hexane for many cases. The first-order PCM SAC-CI is applied to studying the solvatochromisms of (2,2{sup ′}-bipyridine)tetracarbonyltungsten [W(CO){sub 4}(bpy), bpy = 2,2{sup ′}-bipyridine] and bis(pentacarbonyltungsten)pyrazine [(OC){sub 5}W(pyz)W(CO){sub 5}, pyz = pyrazine]. The SAC-CI calculations reveal the detailed character of the excited states and the mechanisms of solvent shifts. The energies of metal to ligand charge transfer states are significantly sensitive to solvents. The first-order PCM SAC-CI well reproduces the observed absorption spectra of the tungsten carbonyl complexes in several solvents.« less

[A case of paracoccidioidomycosis with severe adrenal insufficiency].

PubMed

Yoshimura, Yukihiro; Tachikawa, Natsuo; Oosawa, Takayuki; Kosuge, Youko; Kamei, Katsuhiko

2012-05-01

Paracoccidioidomycosis (PCM) is the most common systemic fungal disease in central-south America, but is rare in Japan. We experiensed a case of PCM in a patient, who came from Bolivia and presented with mouth pain and reduced dietary intake but no fever. Adrenal insufficiency was diagnosed with extremely high serum adrenocorticotropic hormone (ACTH) and was resolved with hormone supplementation. The PCM was treated with trimethoprim-sulfamethoxazole which was switched to itraconazole and improvement was achieved.

Application of TRIZ Theory in Patternless Casting Manufacturing Technique

NASA Astrophysics Data System (ADS)

Yang, Weidong; Gan, Dequan; Jiang, Ping; Tian, Yumei

The ultimate goal of Patternless Casting Manufacturing (referred to as PCM) is how to obtain the casts by casting the sand mold directly. In the previous PCM, the resin content of sand mold is much higher than that required by traditional resin sand, so the casts obtained are difficult to be sound and qualified products, which limits the application of this technique greatly. In this paper, the TRIZ algorithm is introduced to the innovation process in PCM systematically.

Analysis of the vibration modes of piezoelectric circular microdiaphragms

NASA Astrophysics Data System (ADS)

Olfatnia, M.; Singh, V. R.; Xu, T.; Miao, J. M.; Ong, L. S.

2010-08-01

The vibration modes of a piezoelectric circular microdiaphragm (PCM) are visualized and investigated in this paper. The PCM was previously fabricated by combining sol-gel PZT thin film and MEMS technology (Olfatnia et al 2010 J. Micromech. Microeng. 20 015007). We used a reflection digital holography microscope to visualize different frequency modes. It was found that the degeneracy of the modes with at least one nodal diameter is broken, even though it was expected that these orthogonal modes are degenerated in frequency (Meirovitch 1967 Analytical Methods in Vibrations (New York: Macmillan)). These non-degenerated modes are correlated to the lack of symmetry of the PCM, mainly imposed by the top electrode configuration. The theoretical and experimental measurements of the resonance frequency of different modes show that even though for the first fundamental mode, the diaphragm behaves more like a membrane, in higher modes the stiffness contribution increases, for instance, from 6% in mode (0, 1) to 46% in mode (0, 3). Finite element simulations demonstrate that the frequency shift of the PCM to mass loading increases in higher frequency modes. This shift is almost 8.5 times higher in mode (0, 3) than in mode (0, 1). The impedance characterization of the PCM shows that by applying higher excitation voltages, more vibration modes can be excited. However, these higher voltages induce geometric nonlinearities in the PCM, which in turn increases the resonant frequency of the device.

Low-cost phase change material as an energy storage medium in building envelopes: Experimental and numerical analyses

DOE PAGES

Biswas, Kaushik; Abhari, Ramin

2014-10-03

A promising approach to increasing the energy efficiency of buildings is the implementation of a phase change material (PCM) in the building envelope. Numerous studies over the last two decades have reported the energy saving potential of PCMs in building envelopes, but their wide application has been inhibited, in part, by their high cost. This article describes a novel PCM made of naturally occurring fatty acids/glycerides trapped into high density polyethylene (HDPE) pellets and its performance in a building envelope application. The PCM-HDPE pellets were mixed with cellulose insulation and then added to an exterior wall of a test buildingmore » in a hot and humid climate, and tested over a period of several months, To demonstrate the efficacy of the PCM-enhanced cellulose insulation in reducing the building envelope heat gains and losses, side-by-side comparison was performed with another wall section filled with cellulose-only insulation. Further, numerical modeling of the test wall was performed to determine the actual impact of the PCM-HDPE pellets on wall-generated heating and cooling loads and the associated electricity consumption. The model was first validated using experimental data and then used for annual simulations using typical meteorological year (TMY3) weather data. Furthermore, this article presents the experimental data and numerical analyses showing the energy-saving potential of the new PCM.« less

Optimal design variable considerations in the use of phase change materials in indirect evaporative cooling

NASA Astrophysics Data System (ADS)

Chilakapaty, Ankit Paul

The demand for sustainable, energy efficient and cost effective heating and cooling solutions is exponentially increasing with the rapid advancement of computation and information technology. Use of latent heat storage materials also known as phase change materials (PCMs) for load leveling is an innovative solution to the data center cooling demands. These materials are commercially available in the form of microcapsules dispersed in water, referred to as the microencapsulated phase change slurries and have higher heat capacity than water. The composition and physical properties of phase change slurries play significant role in energy efficiency of the cooling systems designed implementing these PCM slurries. Objective of this project is to study the effect of PCM particle size, shape and volumetric concentration on overall heat transfer potential of the cooling systems designed with PCM slurries as the heat transfer fluid (HTF). In this study uniform volume heat source model is developed for the simulation of heat transfer potential using phase change materials in the form of bulk temperature difference in a fully developed flow through a circular duct. Results indicate the heat transfer potential increases with PCM volumetric concentration with gradually diminishing returns. Also, spherical PCM particles offer greater heat transfer potential when compared to cylindrical particles. Results of this project will aid in efficient design of cooling systems based on PCM slurries.

Differential response to gepirone but not to chlordiazepoxide in malnourished rats subjected to learned helplessness.

PubMed

Camargo, L M M; Nascimento, A B; Almeida, S S

2008-01-01

The learned helplessness (LH) paradigm is characterized by learning deficits resulting from inescapable events. The aims of the present study were to determine if protein-calorie malnutrition (PCM) alters learning deficits induced by LH and if the neurochemical changes induced by malnutrition alter the reactivity to treatment with GABA-ergic and serotonergic drugs during LH. Well-nourished (W) and PCM Wistar rats (61 days old) were exposed or not to inescapable shocks (IS) and treated with gepirone (GEP, 0.0-7.5 mg/kg, intraperitoneally, N = 128) or chlordiazepoxide (0.0-7.5 mg/kg, intraperitoneally, N = 128) 72 h later, 30 min before the test session (30 trials of escape learning). The results showed that rats exposed to IS had higher escape latency than non-exposed rats (12.6 +/- 2.2 vs 4.4 +/- 0.8 s) and that malnutrition increased learning impairment produced by LH. GEP increased the escape latency of W animals exposed or non-exposed to IS, but did not affect the response of PCM animals, while chlordiazepoxide reduced the escape deficit of both W and PCM rats. The data suggest that PCM animals were more sensitive to the impairment produced by LH and that PCM led to neurochemical changes in the serotonergic system, resulting in hyporeactivity to the anxiogenic effects of GEP in the LH paradigm.

Materials and other needs for advanced phase change memory (Presentation Recording)

NASA Astrophysics Data System (ADS)

Sosa, Norma E.

2015-09-01

Phase change memory (PCM), with its long history, may now hold its brightest promise to date. This bright future is being fueled by the "push" from big data. PCM is a non-volatile memory technology used to create solid-state random access memory devices that operate based the resistance properties of materials. Employing the electrical resistance differences-as opposed to differences in charge stored-between the amorphous and crystalline phases of the material, PCM can store bits, namely one's and zero's. Indeed, owing to the method of storage, PCM can in fact be designed to hold multiple bits thus leading to a high-density technology twice the storage density and less than half the cost of DRAM, the main kind found in typical personal computers. It has been long known that PCM can fill a need gap that spans 3 decades in performance from DRAM to solid state drive (NAND Flash). Furthermore, PCM devices can lead to performance and reliability improvements essential to enabling significant steps forward to supporting big data centric computing. This talk will focus on the science and challenges of aggressive scaling to realize the density needed, how this scaling challenge is intertwined with materials needs for endurance into the giga-cycles, and the associated forefront research aiming to realizing multi-level functionality into these nanoscale programmable resistor devices.

Submerged AUV Charging Station

NASA Technical Reports Server (NTRS)

Jones, Jack A.; Chao, Yi; Curtin, Thomas

2014-01-01

Autonomous Underwater Vehicles (AUVs) are becoming increasingly important for military surveillance and mine detection. Most AUVs are battery powered and have limited lifetimes of a few days to a few weeks. This greatly limits the distance that AUVs can travel underwater. Using a series of submerged AUV charging stations, AUVs could travel a limited distance to the next charging station, recharge its batteries, and continue to the next charging station, thus traveling great distances in a relatively short time, similar to the Old West “Pony Express.” One solution is to use temperature differences at various depths in the ocean to produce electricity, which is then stored in a submerged battery. It is preferred to have the upper buoy submerged a reasonable distance below the surface, so as not to be seen from above and not to be inadvertently destroyed by storms or ocean going vessels. In a previous invention, a phase change material (PCM) is melted (expanded) at warm temperatures, for example, 15 °C, and frozen (contracted) at cooler temperatures, for example, 8 °C. Tubes containing the PCM, which could be paraffin such as pentadecane, would be inserted into a container filled with hydraulic oil. When the PCM is melted (expanded), it pushes the oil out into a container that is pressurized to about 3,000 psi (approx equals 20.7 MPa). When a valve is opened, the high-pressure oil passes through a hydraulic motor, which turns a generator and charges a battery. The low-pressure oil is finally reabsorbed into the PCM canister when the PCM tubes are frozen (contracted). Some of the electricity produced could be used to control an external bladder or a motor to the tether line, such that depth cycling is continued for a very long period of time. Alternatively, after the electricity is generated by the hydraulic motor, the exiting low-pressure oil from the hydraulic motor could be vented directly to an external bladder on the AUV, such that filling of the bladder causes the AUV to rise, and emptying of the bladder allows the AUV to descend. This type of direct buoyancy control is much more energy efficient than using electrical pumps in that the inefficiencies of converting thermal energy to electrical energy to mechanical energy is avoided. AUV charging stations have been developed that use electricity produced by waves on floating buoys and that use electricity from solar photovoltaics on floating buoys. This is the first device that has absolutely no floating or visible parts, and is thus impervious to storms, inadvertent ocean vessel collisions, or enemy sabotage.

MiRNA-128 regulates the proliferation and neurogenesis of neural precursors by targeting PCM1 in the developing cortex

PubMed Central

Zhang, Wei; Kim, Paul Jong; Chen, Zhongcan; Lokman, Hidayat; Qiu, Lifeng; Zhang, Ke; Rozen, Steven George; Tan, Eng King; Je, Hyunsoo Shawn; Zeng, Li

2016-01-01

During the development, tight regulation of the expansion of neural progenitor cells (NPCs) and their differentiation into neurons is crucial for normal cortical formation and function. In this study, we demonstrate that microRNA (miR)-128 regulates the proliferation and differentiation of NPCs by repressing pericentriolar material 1 (PCM1). Specifically, overexpression of miR-128 reduced NPC proliferation but promoted NPC differentiation into neurons both in vivo and in vitro. In contrast, the reduction of endogenous miR-128 elicited the opposite effects. Overexpression of miR-128 suppressed the translation of PCM1, and knockdown of endogenous PCM1 phenocopied the observed effects of miR-128 overexpression. Furthermore, concomitant overexpression of PCM1 and miR-128 in NPCs rescued the phenotype associated with miR-128 overexpression, enhancing neurogenesis but inhibiting proliferation, both in vitro and in utero. Taken together, these results demonstrate a novel mechanism by which miR-128 regulates the proliferation and differentiation of NPCs in the developing neocortex. DOI: http://dx.doi.org/10.7554/eLife.11324.001 PMID:26883496

Development of multicomponent hybrid density functional theory with polarizable continuum model for the analysis of nuclear quantum effect and solvent effect on NMR chemical shift.

PubMed

Kanematsu, Yusuke; Tachikawa, Masanori

2014-04-28

We have developed the multicomponent hybrid density functional theory [MC_(HF+DFT)] method with polarizable continuum model (PCM) for the analysis of molecular properties including both nuclear quantum effect and solvent effect. The chemical shifts and H/D isotope shifts of the picolinic acid N-oxide (PANO) molecule in chloroform and acetonitrile solvents are applied by B3LYP electron exchange-correlation functional for our MC_(HF+DFT) method with PCM (MC_B3LYP/PCM). Our MC_B3LYP/PCM results for PANO are in reasonable agreement with the corresponding experimental chemical shifts and isotope shifts. We further investigated the applicability of our method for acetylacetone in several solvents.

Recent advances in pericentriolar material organization: ordered layers and scaffolding gels.

PubMed

Fry, Andrew M; Sampson, Josephina; Shak, Caroline; Shackleton, Sue

2017-01-01

The centrosome is an unusual organelle that lacks a surrounding membrane, raising the question of what limits its size and shape. Moreover, while electron microscopy (EM) has provided a detailed view of centriole architecture, there has been limited understanding of how the second major component of centrosomes, the pericentriolar material (PCM), is organized. Here, we summarize exciting recent findings from super-resolution fluorescence imaging, structural biology, and biochemical reconstitution that together reveal the presence of ordered layers and complex gel-like scaffolds in the PCM. Moreover, we discuss how this is leading to a better understanding of the process of microtubule nucleation, how alterations in PCM size are regulated in cycling and differentiated cells, and why mutations in PCM components lead to specific human pathologies.

Recent advances in pericentriolar material organization: ordered layers and scaffolding gels

PubMed Central

Fry, Andrew M.; Sampson, Josephina; Shak, Caroline; Shackleton, Sue

2017-01-01

The centrosome is an unusual organelle that lacks a surrounding membrane, raising the question of what limits its size and shape. Moreover, while electron microscopy (EM) has provided a detailed view of centriole architecture, there has been limited understanding of how the second major component of centrosomes, the pericentriolar material (PCM), is organized. Here, we summarize exciting recent findings from super-resolution fluorescence imaging, structural biology, and biochemical reconstitution that together reveal the presence of ordered layers and complex gel-like scaffolds in the PCM. Moreover, we discuss how this is leading to a better understanding of the process of microtubule nucleation, how alterations in PCM size are regulated in cycling and differentiated cells, and why mutations in PCM components lead to specific human pathologies. PMID:29026530

A low jitter PLL clock used for phase change memory

NASA Astrophysics Data System (ADS)

Xiao, Hong; Houpeng, Chen; Zhitang, Song; Daolin, Cai; Xi, Li

2013-02-01

A fully integrated low-jitter, precise frequency CMOS phase-locked loop (PLL) clock for the phase change memory (PCM) drive circuit is presented. The design consists of a dynamic dual-reset phase frequency detector (PFD) with high frequency acquisition, a novel low jitter charge pump, a CMOS ring oscillator based voltage-controlled oscillator (VCO), a 2nd order passive loop filter, and a digital frequency divider. The design is fabricated in 0.35 μm CMOS technology and consumes 20 mW from a supply voltage of 5 V. In terms of the PCM's program operation requirement, the output frequency range is from 1 to 140 MHz. For the 140 MHz output frequency, the circuit features a cycle-to-cycle jitter of 28 ps RMS and 250 ps peak-to-peak.

The influence of flow modification on air and PCM temperatures in an accumulative heat exchanger

NASA Astrophysics Data System (ADS)

Borcuch, Marcin; Musiał, Michał; Sztekler, Karol; Kalawa, Wojciech; Gumuła, Stanisław; Stefański, Sebastian

2018-06-01

The paper presents the influence of flow modification on the operation of an accumulative heat exchanger. This device can be used as a regenerator in ventilation and air supply systems. A heat exchanger uses ceresine (a mixture of paraffins) as a phase change material (PCM). The aim of this research was to determine the effect of flow modification on temperature distribution and pressure drops in the device. The introduction contains a short description of the test stand used, including the accumulative heat exchanger, the guide vanes, and the locations of measurement and control equipment. We found that additional objects limited vortex structures, increased the inside temperature, and dropped the pressure along the heat exchanger. Guidelines for further research are proposed and briefly discussed.

What are the potential benefits of including latent storage in common wallboard?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, T.K.; Tomlinson, J.J.

1992-07-01

Previous work has shown that wallboard can be successfully manufactured to contain up to 30% phase change material (PCM), or wax, thus enabling this common building material to serve as a thermal energy storage device. This material was analyzed for passive solar applications and found to save energy with a reasonable pay-back time period. Further evaluations of the wallboard are reported in this paper. This analysis looks at potential applications of PCM wallboard as a load management device and as a comfort enhancer. Results show that the wallboard is ineffective in modifying the comfort level but can provide significant loadmore » management relief with no energy penalty. Modifications to typical heating and air-conditioning control strategies were necessary for successful load management.« less

What are the potential benefits of including latent storage in common wallboard

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, T.K.; Tomlinson, J.J.

1992-01-01

Previous work has shown that wallboard can be successfully manufactured to contain up to 30% phase change material (PCM), or wax, thus enabling this common building material to serve as a thermal energy storage device. This material was analyzed for passive solar applications and found to save energy with a reasonable pay-back time period. Further evaluations of the wallboard are reported in this paper. This analysis looks at potential applications of PCM wallboard as a load management device and as a comfort enhancer. Results show that the wallboard is ineffective in modifying the comfort level but can provide significant loadmore » management relief with no energy penalty. Modifications to typical heating and air-conditioning control strategies were necessary for successful load management.« less

Lessons Learned in the Specification, Purchase, Validation and Final Installation Process of a Replacement PCM Bit Synchronizer

NASA Technical Reports Server (NTRS)

Price, Richard N.

2007-01-01

This paper intends to describe the lessons learned while specifying validating and installing a bit sync to replace the 30 year old Aydin Model 335a PCM bit sync used in the Space Shuttle Launch Control Center. The engineer had to analyze the original requirements and specifications and then create new requirements documentation that more correctly described our needs. One issue to consider was the removal of unnecessary requirements such as various data formats when only one format is used. The conversion to a system that no longer has an assortment of analog rotary switches required retraining of the operators. Finally, post-procurement corrections for undisclosed user requirements and missed design requirements required close contact with a manufacturer who was willing to accommodate the changes.

Reversible optical switching of highly confined phonon-polaritons with an ultrathin phase-change material

NASA Astrophysics Data System (ADS)

Li, Peining; Yang, Xiaosheng; Maß, Tobias W. W.; Hanss, Julian; Lewin, Martin; Michel, Ann-Katrin U.; Wuttig, Matthias; Taubner, Thomas

2016-08-01

Surface phonon-polaritons (SPhPs), collective excitations of photons coupled with phonons in polar crystals, enable strong light-matter interaction and numerous infrared nanophotonic applications. However, as the lattice vibrations are determined by the crystal structure, the dynamical control of SPhPs remains challenging. Here, we realize the all-optical, non-volatile, and reversible switching of SPhPs by controlling the structural phase of a phase-change material (PCM) employed as a switchable dielectric environment. We experimentally demonstrate optical switching of an ultrathin PCM film (down to 7 nm, <λ/1,200) with single laser pulses and detect ultra-confined SPhPs (polariton wavevector kp > 70k0, k0 = 2π/λ) in quartz. Our proof of concept allows the preparation of all-dielectric, rewritable SPhP resonators without the need for complex fabrication methods. With optimized materials and parallelized optical addressing we foresee application potential for switchable infrared nanophotonic elements, for example, imaging elements such as superlenses and hyperlenses, as well as reconfigurable metasurfaces and sensors.

Experimental studies on cycling stable characteristics of inorganic phase change material CaCl2·6H2O-MgCl2·6H2O modified with SrCl2·6H2O and CMC

NASA Astrophysics Data System (ADS)

He, Meizhi; Yang, Luwei; Zhang, Zhentao

2018-01-01

By means of mass ratio method, binary eutectic hydrated salts inorganic phase change thermal energy storage system CaCl2·6H2O-20wt% MgCl2·6H2O was prepared, and through adding nucleating agent 1wt% SrCl2·6H2O and thickening agent 0.5wt% carboxy methyl cellulose (CMC), inoganic phase change material (PCM) modified was obtained. With recording cooling-melting curves simultaneously, this PCM was frozen and melted for 100 cycles under programmable temperature control. After per 10 cycles, the PCM was charaterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD) and density meter, then analysing variation characteristics of phase change temperature, supercooling degree, superheat degree, latent heat, crystal structure and density with the increase of cycle index. The results showed that the average values of average phase change temperature for cooling and heating process were 25.70°C and 27.39°C respectively with small changes. The average values of average supercooling and superheat degree were 0.59°C and 0.49°C respectively, and the maximum value was 1.10°C. The average value and standard deviation of latent heat of fusion were 120.62 J/g and 1.90 J/g respectively. Non-molten white solid sediments resulted from phase separation were tachyhydrite (CaMg2Cl6·12H2O), which was characterized by XRD. Measuring density of the PCM after per 10 cycles, and the results suggested that the total mass of tachyhydrite was limited. In summary, such modified inoganic PCM CaCl2·6H2O-20wt% MgCl2·6H2O-1wt% SrCl2·6H2O-0.5wt% CMC could stay excellent circulation stability within 100 cycles, and providing reference value in practical use.

Prevalence and Serological Diagnosis of Relapse in Paracoccidioidomycosis Patients

PubMed Central

Sylvestre, Tatiane Fernanda; Silva, Luciane Regina Franciscone; Cavalcante, Ricardo de Souza; Moris, Daniela Vanessa; Venturini, James; Vicentini, Adriana Pardini; de Carvalho, Lídia Raquel; Mendes, Rinaldo Poncio

2014-01-01

A review of 400 clinical records of paracoccidioidomycosis (PCM) patients, 93 with the acute/subacute (AF) and 307 with the chronic form (CF), attended from 1977 to 2011, selected as to the schedule of release for study by the Office of Medical Records at the University Hospital of the Faculdade de Medicina de Botucatu – São Paulo State University – UNESP, was performed to detect cases in relapse. The control of cure was performed by clinical and serological evaluation using the double agar gel immunodiffusion test (DID). In the diagnosis of relapse, DID, enzyme-linked immunosorbent assay (ELISA) and immunoblotting assay (IBgp70 and IBgp43) were evaluated. Out of 400 patients, 21 (5.2%) went through relapse, 18 of them were male and 3 were female, 6∶1 male/female ratio. Out of the 21 patients in relapse, 15 (4.8%) showed the CF, and 6 (6.4%) the AF (p>0.05). The sensitivity of DID and ELISA before treatment was the same (76.1%). DID presented higher sensitivity in pre-treatment (80%) than at relapse (45%; p = 0.017), while ELISA showed the same sensitivity (80% vs 65%; p = 0.125). The serological methods for identifying PCM patients in relapse showed low rates of sensitivity, from 12.5% in IBgp70 to 65.0% in IBgp43 identification and 68.8% in ELISA. The sensitivity of ELISA in diagnosing PCM relapse showed a strong tendency to be higher than DID (p = 0.06) and is equal to IBgp43 (p = 0.11). In sum, prevalence of relapse was not high in PCM patients whose treatment duration was based on immunological parameters. However, the used methods for serological diagnosis present low sensitivity. While more accurate serological methods are not available, we pay special attention to the mycological and histopathological diagnosis of PCM relapse. Hence, direct mycological, cytopathological, and histopathological examinations and isolation in culture for P. brasiliensis must be appropriately and routinely performed when the hypothesis of relapse is considered. PMID:24787147

Collagen Type IV and Laminin Expressions during Cartilage Repair and in Late Clinically Failed Repair Tissues from Human Subjects

PubMed Central

Foldager, Casper Bindzus; Toh, Wei Seong; Christensen, Bjørn Borsøe; Lind, Martin; Gomoll, Andreas H.; Spector, Myron

2016-01-01

Objective To identify the collagen type IV (Col4) isoform in articular cartilage and to evaluate the expressions of Col4 and laminin in the pericellular matrix (PCM) in damaged cartilage and during cartilage repair. Design The Col4 isoform was determined in chondrocytes isolated from 6 patients cultured up to 6 days and in 21% O2 or 1% O2, and the gene expression of Col4 α-chains was investigated. The distribution of Col4 and laminin in traumatically damaged cartilage (n = 7) and clinically failed cartilage repair (microfracture, TruFit, autologous chondrocyte implantation; n = 11) were investigated using immunohistochemistry. Normal human cartilage was used as control (n = 8). The distribution during clinical cartilage repair procedures was investigated in a minipig model with 6-month follow-up (untreated chondral, untreated osteochondral, microfracture, autologous chondrocyte implantation; n = 10). Results The Col4 isoform in articular cartilage was characterized as α1α1α2, which is an isoform containing antiangiogenic domains in the NC1-terminals (arresten and canstatin). In normal cartilage, laminin and Col4 was exclusively found in the PCM. High amounts (>50%) of Col4 in the PCM significantly decreased in damaged cartilage (P = 0.004) and clinically failed repair tissue (P < 0.001). Laminin was only found with high expression (>50%) in 4/8 of the normal samples, which was not statistically significantly different from damaged cartilage (P = 0.15) or failed cartilage repair (P = 0.054). Conclusions Col4 in cartilage contain antiangiogenic domains and may play a role in the hypoxic environment in articular cartilage. Col4 and laminin was not found in the PCM of damaged and clinically failed repair. PMID:26958317

Computation of forces arising from the polarizable continuum model within the domain-decomposition paradigm

NASA Astrophysics Data System (ADS)

Gatto, Paolo; Lipparini, Filippo; Stamm, Benjamin

2017-12-01

The domain-decomposition (dd) paradigm, originally introduced for the conductor-like screening model, has been recently extended to the dielectric Polarizable Continuum Model (PCM), resulting in the ddPCM method. We present here a complete derivation of the analytical derivatives of the ddPCM energy with respect to the positions of the solute's atoms and discuss their efficient implementation. As it is the case for the energy, we observe a quadratic scaling, which is discussed and demonstrated with numerical tests.

Antigenemia in Patients with Paracoccidioidomycosis: Detection of the 87-Kilodalton Determinant during and after Antifungal Therapy

PubMed Central

Gómez, B. L.; Figueroa, J. I.; Hamilton, A. J.; Diez, S.; Rojas, M.; Tobón, A. M.; Hay, R. J.; Restrepo, A.

1998-01-01

Serological diagnosis and follow-up of paracoccidioidomycosis (PCM) patients have relied mainly on the detection of antibody responses by using techniques such as complement fixation (CF) and immunodiffusion. We recently described a novel inhibition enzyme-linked immunosorbent assay (inh-ELISA) which proved to be useful in the diagnosis of PCM via the detection of an 87-kDa determinant in patient sera (B. L. Gomez, J. I. Figueroa, A. J. Hamilton, B. Ortiz, M. A. Robledo, R. J. Hay, and A. Restrepo, J. Clin. Microbiol. 35:3278–3283, 1997). This test has now been assessed as a means of following up PCM patients. A total of 24 PCM patients, classified according to their clinical presentation (6 with the acute form of the disease, of whom two had AIDS, 12 with the multifocal form of the disease, and 6 with the unifocal form of the disease), were studied. The four human immunodeficiency virus-negative patients with acute PCM showed a statistically significant decrease in circulating antigen levels after the start of antifungal therapy. Antigen levels in this group became negative by our criteria (≤2.3 μg/ml) before week 20 and remained so in three of four of these patients. In contrast, the two AIDS patients who also presented with the acute form of PCM showed no statistically significant decrease in circulating antigen levels even after 68 weeks of therapy. Taken together as a group, the patients with the multifocal form showed a statistically significant decrease in antigenemia after 28 weeks of therapy. In addition, five of six patients with the unifocal form became antigen negative by week 40. Antigen level decrease mirrored clinical cure in the majority of patients in all clinical groups; in contrast, measurement of anti-PCM antibodies via the CF test showed wide fluctuations in titers during the follow-up period. The inh-ELISA for the detection of the 87-kDa Paracoccidioides brasiliensis determinant would appear to be a valuable additional tool in the follow-up of PCM patients. PMID:9774584

NASA Tech Briefs, August 2005

NASA Technical Reports Server (NTRS)

2005-01-01

Topics include: Hidden Identification on Parts: Magnetic Machine-Readable Matrix Symbols; System for Processing Coded OFDM Under Doppler and Fading; Multipurpose Hyperspectral Imaging System; Magnetic-Flux-Compensated Voltage Divider; High-Performance Satellite/Terrestrial-Network Gateway; Internet-Based System for Voice Communication With the ISS; Stripline/Microstrip Transition in Multilayer Circuit Board; Dual-Band Feed for a Microwave Reflector Antenna; Quadratic Programming for Allocating Control Effort; Range Process Simulation Tool; Simulator of Space Communication Networks; Computing Q-D Relationships for Storage of Rocket Fuels; Contour Error Map Algorithm; Portfolio Analysis Tool; Glass Frit Filters for Collecting Metal Oxide Nanoparticles; Anhydrous Proton-Conducting Membranes for Fuel Cells; Portable Electron-Beam Free-Form Fabrication System; Miniature Laboratory for Detecting Sparse Biomolecules; Multicompartment Liquid-Cooling/Warming Protective Garments; Laser Metrology for an Optical-Path-Length Modulator; PCM Passive Cooling System Containing Active Subsystems; Automated Electrostatics Environmental Chamber; Estimating Aeroheating of a 3D Body Using a 2D Flow Solver; Artificial Immune System for Recognizing Patterns; Computing the Thermodynamic State of a Cryogenic Fluid; Safety and Mission Assurance Performance Metric; Magnetic Control of Concentration Gradient in Microgravity; Avionics for a Small Robotic Inspection Spacecraft; and Simulation of Dynamics of a Flexible Miniature Airplane.

26 CFR 1.460-1 - Long-term contracts.

Code of Federal Regulations, 2011 CFR

2011-04-01

... attributable to designing the satellite and developing computer software using the PCM. Example 7. Non-long... customer has title to, control over, or bears the risk of loss from, the property manufactured or... as design and engineering costs, other than expenses attributable to bidding and negotiating...

26 CFR 1.460-1 - Long-term contracts.

Code of Federal Regulations, 2012 CFR

2012-04-01

... attributable to designing the satellite and developing computer software using the PCM. Example 7. Non-long... customer has title to, control over, or bears the risk of loss from, the property manufactured or... as design and engineering costs, other than expenses attributable to bidding and negotiating...

26 CFR 1.460-1 - Long-term contracts.

Code of Federal Regulations, 2014 CFR

2014-04-01

... attributable to designing the satellite and developing computer software using the PCM. Example 7. Non-long... customer has title to, control over, or bears the risk of loss from, the property manufactured or... as design and engineering costs, other than expenses attributable to bidding and negotiating...

26 CFR 1.460-1 - Long-term contracts.

Code of Federal Regulations, 2013 CFR

2013-04-01

... attributable to designing the satellite and developing computer software using the PCM. Example 7. Non-long... customer has title to, control over, or bears the risk of loss from, the property manufactured or... as design and engineering costs, other than expenses attributable to bidding and negotiating...

Thermal analysis of void cavity for heat pipe receiver under microgravity

NASA Astrophysics Data System (ADS)

Gui, Xiaohong; Song, Xiange; Nie, Baisheng

2017-04-01

Based on theoretical analysis of PCM (Phase Change Material) solidification process, the model of improved void cavity distribution tending to high temperature region is established. Numerical results are compared with NASA (National Aeronautics and Space Administration) results. Analysis results show that the outer wall temperature, the melting ratio of PCM and the temperature gradient of PCM canister, have great difference in different void cavity distribution. The form of void distribution has a great effect on the process of phase change. Based on simulation results under the model of improved void cavity distribution, phase change heat transfer process in thermal storage container is analyzed. The main goal of the improved designing for PCM canister is to take measures in reducing the concentration distribution of void cavity by adding some foam metal into phase change material.

Stability and corrosion testing of a high temperature phase change material for CSP applications

NASA Astrophysics Data System (ADS)

Liu, Ming; Bell, Stuart; Tay, Steven; Will, Geoffrey; Saman, Wasim; Bruno, Frank

2016-05-01

This paper presents the stability and corrosion testing results of a candidate high temperature phase change material (PCM) for potential use in concentrating solar power applications. The investigated PCM is a eutectic mixture of NaCl and Na2CO3 and both are low cost materials. This PCM has a melting temperature of 635 °C and a relatively high latent heat of fusion of 308.1 J/g. The testing was performed by means of an electric furnace subjected to 150 melt-freeze cycles between 600 °C and 650 °C. The results showed that this PCM candidate has no obvious decomposition up to 650 °C after 150 cycles and stainless steel 316 potentially can be used as the containment material under the minimized oxygen atmosphere.

Rheological and thermal properties of suspensions of microcapsules containing phase change materials.

PubMed

Cao, Vinh Duy; Salas-Bringas, Carlos; Schüller, Reidar Barfod; Szczotok, Anna M; Hiorth, Marianne; Carmona, Manuel; Rodriguez, Juan F; Kjøniksen, Anna-Lena

2018-01-01

The thermal and rheological properties of suspensions of microencapsulated phase change materials (MPCM) in glycerol were investigated. When the microcapsule concentration is raised, the heat storage capacity of the suspensions becomes higher and a slight decline in the thermal conductivity of the suspensions is observed. The temperature-dependent shear-thinning behaviour of the suspensions was found to be strongly affected by non-encapsulated phase change materials (PCM). Accordingly, the rheological properties of the MPCM suspensions could be described by the Cross model below the PCM melting point while a power law model best described the data above the PCM melting point. The MPCM suspensions are interesting for energy storage and heat transfer applications. However, the non-encapsulated PCM contributes to the agglomeration of the microcapsules, which can lead to higher pumping consumption and clogging of piping systems.

Structured illumination of the interface between centriole and peri-centriolar material

PubMed Central

Fu, Jingyan; Glover, David M.

2012-01-01

The increase in centrosome size in mitosis was described over a century ago, and yet it is poorly understood how centrioles, which lie at the core of centrosomes, organize the pericentriolar material (PCM) in this process. Now, structured illumination microscopy reveals in Drosophila that, before clouds of PCM appear, its proteins are closely associated with interphase centrioles in two tube-like layers: an inner layer occupied by centriolar microtubules, Sas-4, Spd-2 and Polo kinase; and an outer layer comprising Pericentrin-like protein (Dplp), Asterless (Asl) and Plk4 kinase. Centrosomin (Cnn) and γ-tubulin associate with this outer tube in G2 cells and, upon mitotic entry, Polo activity is required to recruit them together with Spd-2 into PCM clouds. Cnn is required for Spd-2 to expand into the PCM during this maturation process but can itself contribute to PCM independently of Spd-2. By contrast, the centrioles of spermatocytes elongate from a pre-existing proximal unit during the G2 preceding meiosis. Sas-4 is restricted to the microtubule-associated, inner cylinder and Dplp and Cnn to the outer cylinder of this proximal part. γ-Tubulin and Asl associate with the outer cylinder and Spd-2 with the inner cylinder throughout the entire G2 centriole. Although they occupy different spatial compartments on the G2 centriole, Cnn, Spd-2 and γ-tubulin become diminished at the centriole upon entry into meiosis to become part of PCM clouds. PMID:22977736

Cumulative energy demand and global warming potential of a building-integrated solar thermal system with/without phase change material.

PubMed

Lamnatou, Chr; Motte, F; Notton, G; Chemisana, D; Cristofari, C

2018-04-15

Building-integrated solar thermal (BIST) systems are a specific type of solar thermal systems which are integrated into the building and they participate in building functionality. The present article is about the life-cycle assessment of different options of a BIST system (Mediterranean climatic conditions: Ajaccio, France). The environmental profile of the studied configurations is assessed by means of CED (cumulative energy demand), GWP (global warming potential) and EPBT (energy payback time). The proposed configurations (for the collector) include: i) a system without PCM (phase change material) using only rock wool as insulation and ii) a system with PCM (myristic acid) and rock wool. Concerning life-cycle results based on CED and GWP 100a (scenario without recycling), the configuration without PCM shows 0.67 MJ prim /kWh and 0.06 kg CO 2.eq /kWh while the configuration with PCM presents 0.74 MJ prim /kWh and 0.08 kg CO 2.eq /kWh. Regarding EPBT, if the inputs for pumping/auxiliary heating are not taken into account, both configurations (with/without PCM) have almost the same EPBT (about 1.3 years). On the other hand, if the inputs for pumping/auxiliary heating are considered, EPBT is lower for the system with PCM. In addition, scenarios with recycling have been examined and the results demonstrate that recycling considerably improves the environmental profile of the studied configurations. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects of the heat transfer fluid velocity on the storage characteristics of a cylindrical latent heat energy storage system: a numerical study

NASA Astrophysics Data System (ADS)

Ogoh, Wilson; Groulx, Dominic

2012-03-01

A numerical study of the effects of the thermal fluid velocity on the storage characteristics of a cylindrical latent heat energy storage system (LHESS) was conducted. Due to the low thermal conductivity of phase change materials (PCMs) used in LHESS, fins were added to the system to increase the rate of heat transfer and charging. Finite elements were used to implement the developed numerical method needed to study and solve for the phase change heat transfer (melting of PCM) encountered in a LHESS during charging. The effective heat capacity method was applied in order to account for the large amount of latent energy stored during melting of the PCM and the moving interface between the solid and liquid phases. The effects of the heat transfer fluid (HTF) velocity on the melting rate of the PCM were studied for configurations having between 0 and 18 fins. Results show that the overall heat transfer rate to the PCM increases with an increase in the HTF velocity. However, the effect of the HTF velocity was observed to be small in configurations having very few fins, owing to the large residual thermal resistance offered by the PCM. However, the effect of the HTF velocity becomes more pronounced with addition of fins; since the thermal resistance on the PCM side of the LHESS is significantly reduce by the large number of fins in the system.

Integrating precision cancer medicine into healthcare-policy, practice, and research challenges.

PubMed

Bertier, Gabrielle; Carrot-Zhang, Jian; Ragoussis, Vassilis; Joly, Yann

2016-10-24

Precision medicine (PM) can be defined as a predictive, preventive, personalized, and participatory healthcare service delivery model. Recent developments in molecular biology and information technology make PM a reality today through the use of massive amounts of genetic, 'omics', clinical, environmental, and lifestyle data. With cancer being one of the most prominent public health threats in developed countries, both the research community and governments have been investing significant time, money, and efforts in precision cancer medicine (PCM). Although PCM research is extremely promising, a number of hurdles still remain on the road to an optimal integration of standardized and evidence-based use of PCM in healthcare systems. Indeed, PCM raises a number of technical, organizational, ethical, legal, social, and economic challenges that have to be taken into account in the development of an appropriate health policy framework. Here, we highlight some of the more salient issues regarding the standards needed for integration of PCM into healthcare systems, and we identify fields where more research is needed before policy can be implemented. Key challenges include, but are not limited to, the creation of new standards for the collection, analysis, and sharing of samples and data from cancer patients, and the creation of new clinical trial designs with renewed endpoints. We believe that these issues need to be addressed as a matter of priority by public health policymakers in the coming years for a better integration of PCM into healthcare.

Paracoccidioidomycosis in southern Rio Grande do Sul: a retrospective study of histopathologically diagnosed cases.

PubMed

de Souza, Silvana Pereira; Jorge, Valéria Magalhães; Xavier, Melissa Orzechowski

2014-01-01

Paracoccidioidomycosis (PCM) is a systemic mycosis caused by the fungus Paracoccidioides brasiliensis and is endemic to Brazil. The aim of this study was to perform a retrospective analysis of the PCM cases in the countryside south of Rio Grande do Sul, Brazil. The files from four histopathology laboratories located in the city of Pelotas were obtained, and all of the epidemiological and clinical data from the PCM diagnosed cases were collected for analysis. A total of 123 PCM cases diagnosed between 1966 and 2009 were selected. Of these patients, 104 (84.5%) were male, and 17 were female. The patients ranged from 02 to 92 years of age. Fifty-two cases (41.9%) were obtained from the oral pathology laboratory, and the remaining 71 cases (58.1%) were obtained from the three general pathology laboratories. Of all of the patients studied, 65.2% lived in rural zones and worked in agriculture or other related fields. Data on the evolution of this disease was available for 43 cases, and the time frame ranged from 20 to 2920 days (mean = 572.3 days). An accurate diagnosis performed in less than 30 days only occurred in 21% of the cases. PCM is endemic to the countryside of Rio Grande do Sul. Therefore, it is recommended that PCM be included as a differential diagnosis, mainly for individuals between 30 and 60 years of age, living in rural zones and who have respiratory signs and associated-oropharyngeal lesions.

Paracoccidioidomycosis in southern Rio Grande do Sul: A retrospective study of histopathologically diagnosed cases

PubMed Central

de Souza, Silvana Pereira; Jorge, Valéria Magalhães; Xavier, Melissa Orzechowski

2014-01-01

Paracoccidioidomycosis (PCM) is a systemic mycosis caused by the fungus Paracoccidioides brasiliensis and is endemic to Brazil. The aim of this study was to perform a retrospective analysis of the PCM cases in the countryside south of Rio Grande do Sul, Brazil. The files from four histopathology laboratories located in the city of Pelotas were obtained, and all of the epidemiological and clinical data from the PCM diagnosed cases were collected for analysis. A total of 123 PCM cases diagnosed between 1966 and 2009 were selected. Of these patients, 104 (84.5%) were male, and 17 were female. The patients ranged from 02 to 92 years of age. Fifty-two cases (41.9%) were obtained from the oral pathology laboratory, and the remaining 71 cases (58.1%) were obtained from the three general pathology laboratories. Of all of the patients studied, 65.2% lived in rural zones and worked in agriculture or other related fields. Data on the evolution of this disease was available for 43 cases, and the time frame ranged from 20 to 2920 days (mean = 572.3 days). An accurate diagnosis performed in less than 30 days only occurred in 21% of the cases. PCM is endemic to the countryside of Rio Grande do Sul. Therefore, it is recommended that PCM be included as a differential diagnosis, mainly for individuals between 30 and 60 years of age, living in rural zones and who have respiratory signs and associated-oropharyngeal lesions. PMID:24948940

PCM-SABRE: a platform for benchmarking and comparing outcome prediction methods in precision cancer medicine.

PubMed

Eyal-Altman, Noah; Last, Mark; Rubin, Eitan

2017-01-17

Numerous publications attempt to predict cancer survival outcome from gene expression data using machine-learning methods. A direct comparison of these works is challenging for the following reasons: (1) inconsistent measures used to evaluate the performance of different models, and (2) incomplete specification of critical stages in the process of knowledge discovery. There is a need for a platform that would allow researchers to replicate previous works and to test the impact of changes in the knowledge discovery process on the accuracy of the induced models. We developed the PCM-SABRE platform, which supports the entire knowledge discovery process for cancer outcome analysis. PCM-SABRE was developed using KNIME. By using PCM-SABRE to reproduce the results of previously published works on breast cancer survival, we define a baseline for evaluating future attempts to predict cancer outcome with machine learning. We used PCM-SABRE to replicate previous work that describe predictive models of breast cancer recurrence, and tested the performance of all possible combinations of feature selection methods and data mining algorithms that was used in either of the works. We reconstructed the work of Chou et al. observing similar trends - superior performance of Probabilistic Neural Network (PNN) and logistic regression (LR) algorithms and inconclusive impact of feature pre-selection with the decision tree algorithm on subsequent analysis. PCM-SABRE is a software tool that provides an intuitive environment for rapid development of predictive models in cancer precision medicine.

Osteoarthritis as a disease of the cartilage pericellular matrix.

PubMed

Guilak, Farshid; Nims, Robert; Dicks, Amanda; Wu, Chia-Lung; Meulenbelt, Ingrid

2018-05-22

Osteoarthritis is a painful joint disease characterized by progressive degeneration of the articular cartilage as well as associated changes to the subchondral bone, synovium, and surrounding joint tissues. While the effects of osteoarthritis on the cartilage extracellular matrix (ECM) have been well recognized, it is now becoming apparent that in many cases, the onset of the disease may be initially reflected in the matrix region immediately surrounding the chondrocytes, termed the pericellular matrix (PCM). Growing evidence suggests that the PCM - which along with the enclosed chondrocytes are termed the "chondron" - acts as a critical transducer or "filter" of biochemical and biomechanical signals for the chondrocyte, serving to help regulate the homeostatic balance of chondrocyte metabolic activity in response to environmental signals. Indeed, it appears that alterations in PCM properties and cell-matrix interactions, secondary to genetic, epigenetic, metabolic, or biomechanical stimuli, could in fact serve as initiating or progressive factors for osteoarthritis. Here, we discuss recent advances in the understanding of the role of the PCM, with an emphasis on the reciprocity of changes that occur in this matrix region with disease, as well as how alterations in PCM properties could serve as a driver of ECM-based diseases such as osteoarthritis. Further study of the structure, function, and composition of the PCM in normal and diseased conditions may provide new insights into the understanding of the pathogenesis of osteoarthritis, and presumably new therapeutic approaches for this disease. Copyright © 2017. Published by Elsevier B.V.

Shooting for the Moon or Flying Too Near the Sun? Crossing the Value Rubicon in Precision Cancer Care.

PubMed

Lawler, Mark; French, Declan; Henderson, Raymond; Aggarwal, Ajay; Sullivan, Richard

In his last two State of the Union addresses, President Barack Obama has focused on the need to deliver innovative solutions to improve human health, through the Precision Medicine Initiative in 2015 and the recently announced Cancer Moonshot in 2016. Precision cancer care has delivered clear patient benefit, but even for high-impact medicines such as imatinib mesylate (Glivec) in chronic myeloid leukaemia, the excitement at the success of this practice-changing clinical intervention has been somewhat tempered by the escalating price of this 'poster child' for precision cancer medicine (PCM). Recent studies on the costs of cancer drugs have revealed significant price differentials, which are a major causative factor behind disparities in the access to new generations of immunological and molecularly targeted agents. In this perspective, we will discuss the benefits of PCM to modern cancer control, but also emphasise how increasing costs are rendering the current approaches to integrating the paradigm of PCM unsustainable. Despite the ever increasing pressure on cancer and health care budgets, innovation will and must continue. Value-based frameworks offer one of the most rational approaches for policymakers committed to improving cancer outcomes through a public health approach. © 2016 S. Karger AG, Basel.

Phase Change Material Trade Study: A Comparison Between Wax and Water for Manned Spacecraft

NASA Technical Reports Server (NTRS)

Quinn, Gregory; Hodgson, Ed; Stephan, Ryan A,

2011-01-01

Phase change material heat sinks have been recognized as an important tool in optimizing thermal control systems for space exploration vehicles and habitats that must deal with widely varying thermal loads and environments. In order to better focus technology investment in this arena, NASA has supported a trade study with the objective of identifying where the best potential pay-off can be found among identified aqueous and paraffin wax phase change materials and phase change material heat sink design approaches. The study used a representative exploration mission with well understood parameters to support the trade. Additional sensitivity studies were performed to ensure the applicability of study results across varying systems and destinations. Results from the study indicate that replacing a wax PCM heat sink with a water ice PCM heat sink has the potential to decrease the equivalent system mass of the mission s vehicle through a combination of a smaller heat sink and a slight 5% increase in radiator size or the addition of a lightweight heat pump. An evaluation of existing and emerging PCM heat sink technologies indicates that further mass savings should be achievable through continued development of those technologies. The largest mass savings may be realized by eliminating the melting and freezing pressure of wax and water, respectively.

Thermal Storage System for Electric Vehicle Cabin Heating Component and System Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaClair, Tim J; Gao, Zhiming; Abdelaziz, Omar

Cabin heating of current electric vehicle (EV) designs is typically provided using electrical energy from the traction battery, since waste heat is not available from an engine as in the case of a conventional automobile. In very cold climatic conditions, the power required for space heating of an EV can be of a similar magnitude to that required for propulsion of the vehicle. As a result, its driving range can be reduced very significantly during the winter season, which limits consumer acceptance of EVs and results in increased battery costs to achieve a minimum range while ensuring comfort to themore » EV driver. To minimize the range penalty associated with EV cabin heating, a novel climate control system that includes thermal energy storage from an advanced phase change material (PCM) has been designed for use in EVs and plug-in hybrid electric vehicles (PHEVs). The present paper focuses on the modeling and analysis of this electrical PCM-Assisted Thermal Heating System (ePATHS) and is a companion to the paper Design and Testing of a Thermal Storage System for Electric Vehicle Cabin Heating. A detailed heat transfer model was developed to simulate the PCM heat exchanger that is at the heart of the ePATHS and was subsequently used to analyze and optimize its design. The results from this analysis were integrated into a MATLAB Simulink system model to simulate the fluid flow, pressure drop and heat transfer in all components of the ePATHS. The system model was then used to predict the performance of the climate control system in the vehicle and to evaluate control strategies needed to achieve the desired temperature control in the cabin. The analysis performed to design the ePATHS is described in detail and the system s predicted performance in a vehicle HVAC system is presented.« less

Qualification of APOLLO2 BWR calculation scheme on the BASALA mock-up

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaglio-Gaudard, C.; Santamarina, A.; Sargeni, A.

2006-07-01

A new neutronic APOLLO2/MOC/SHEM/CEA2005 calculation scheme for BWR applications has been developed by the French 'Commissariat a l'Energie Atomique'. This scheme is based on the latest calculation methodology (accurate mutual and self-shielding formalism, MOC treatment of the transport equation) and the recent JEFF3.1 nuclear data library. This paper presents the experimental validation of this new calculation scheme on the BASALA BWR mock-up The BASALA programme is devoted to the measurements of the physical parameters of high moderation 100% MOX BWR cores, in hot and cold conditions. The experimental validation of the calculation scheme deals with core reactivity, fission rate maps,more » reactivity worth of void and absorbers (cruciform control blades and Gd pins), as well as temperature coefficient. Results of the analysis using APOLLO2/MOC/SHEM/CEA2005 show an overestimation of the core reactivity by 600 pcm for BASALA-Hot and 750 pcm for BASALA-Cold. Reactivity worth of gadolinium poison pins and hafnium or B{sub 4}C control blades are predicted by APOLLO2 calculation within 2% accuracy. Furthermore, the radial power map is well predicted for every core configuration, including Void configuration and Hf / B{sub 4}C configurations: fission rates in the central assembly are calculated within the {+-}2% experimental uncertainty for the reference cores. The C/E bias on the isothermal Moderator Temperature Coefficient, using the CEA2005 library based on JEFF3.1 file, amounts to -1.7{+-}03 pcm/ deg. C on the range 10 deg. C-80 deg. C. (authors)« less

Continued Water-Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Hansen, Scott W.; Sheth, Rubik B.; Poynot, Joe; Giglio, Tony; Ungar, Gene K.

2015-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to meet the full heat rejection demands. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HX's do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development two full-scale, Orion sized water-based PCM HX's were constructed by Mezzo Technologies. These HX's were designed by applying prior research on freeze front propagation to a full-scale design. Design options considered included bladder restraint and clamping mechanisms, bladder manufacturing, tube patterns, fill/drain methods, manifold dimensions, weight optimization, and midplate designs. Two units, Units A and B, were constructed and differed only in their midplate design. Both units failed multiple times during testing. This report highlights learning outcomes from these tests and are applied to a final sub-scale PCM HX which is slated to be tested on the ISS in early 2017.

Viscoelastic response of a model endothelial glycocalyx

NASA Astrophysics Data System (ADS)

Nijenhuis, Nadja; Mizuno, Daisuke; Spaan, Jos A. E.; Schmidt, Christoph F.

2009-06-01

Many cells cover themselves with a multifunctional polymer coat, the pericellular matrix (PCM), to mediate mechanical interactions with the environment. A particular PCM, the endothelial glycocalyx (EG), is formed by vascular endothelial cells at their luminal side, forming a mechanical interface between the flowing blood and the endothelial cell layer. The glycosaminoglycan (GAG) hyaluronan (HA) is involved in the main functions of the EG, mechanotransduction of fluid shear stress and molecular sieving. HA, due to its length, is the only GAG in the EG or any other PCM able to form an entangled network. The mechanical functions of the EG are, however, impaired when any one of its components is removed. We here used microrheology to measure the effect of the EG constituents heparan sulfate, chondroitin sulfate, whole blood plasma and albumin on the high-bandwidth mechanical properties of a HA solution. Furthermore, we probed the effect of the hyaldherin aggrecan, a constituent of the PCM of chondrocytes, and very similar to versican (present in the PCM of various cells, and possibly in the EG). We show that components directly interacting with HA (chondroitin sulfate and aggrecan) can increase the viscoelastic shear modulus of the polymer composite.

Asbestos exposure from the overhaul of a Pratt & Whitney R2800 engine.

PubMed

Mlynarek, S P; Van Orden, D R

2012-11-01

This study assessed the asbestos exposures of airplane piston engine mechanics while performing overhaul work on a Pratt & Whitney R2800 radial engine, with tools and practices in use since the time these engines were manufactured. Approximately 40% of the bulk samples collected during this test were found to contain chrysotile. Air samples were collected during the overhaul and were analyzed by phase contrast microscopy (PCM) and transmission electron microscopy (TEM). The average worker exposure during disassembly was 0.0272f/ml (PCM) and ranged from 0.0013 to 0.1240f/ml (PCM) during an average sample collection time of 188min. The average worker exposure during reassembly was 0.0198f/ml (PCM) and ranged from 0.0055 to 0.0913f/ml (PCM) during an average sample collection time of 222min. Only one worker sample (during reassembly) was found to contain asbestos at a concentration of 0.0012f/ml (PCME). Similar results should be found in other aircraft piston engines that use metal clad and non-friable asbestos gaskets, which are the current standard in aircraft piston engines. Copyright © 2012 Elsevier Inc. All rights reserved.

Review of Development Survey of Phase Change Material Models in Building Applications

PubMed Central

Akeiber, Hussein J.; Wahid, Mazlan A.; Hussen, Hasanen M.; Mohammad, Abdulrahman Th.

2014-01-01

The application of phase change materials (PCMs) in green buildings has been increasing rapidly. PCM applications in green buildings include several development models. This paper briefly surveys the recent research and development activities of PCM technology in building applications. Firstly, a basic description of phase change and their principles is provided; the classification and applications of PCMs are also included. Secondly, PCM models in buildings are reviewed and discussed according to the wall, roof, floor, and cooling systems. Finally, conclusions are presented based on the collected data. PMID:25313367

Prevalence of Preventive Cardiovascular Medication Use In Nursing Home Residents. Room for Deprescribing? The SHELTER Study.

PubMed

Malek Makan, Alireza; van Hout, Hein; Onder, Graziano; Finne-Soveri, Harriet; van der Roest, Henriëtte; van Marum, Rob

2017-12-01

In nursing home (NH) residents with a very short life expectancy, the benefits of preventive cardiovascular medication maintenance are questionable. To assess the prevalence of 4 classes of preventive cardiovascular medication (PCM) in NH residents, and to explore differences of prevalence across length of stay, mortality risk, cognitive impairment, functional disability, and across countries. A 12-month prospective cohort study was conducted in 57 NHs in 8 countries (Czech Republic, England, Finland, France, Germany, Italy, The Netherlands, and Israel). We assessed the prevalence at first measurement of 4 classes of PCM: oral anticoagulants (OAC), platelet aggregation inhibitor (PAI), antihypertensive (AHT), and lipid-modifying agent (LMA), in older (60+ years) residents with valid medication assessments. The PCM prevalence was compared across the length of stay (short <60 days, mid, long >12 months), health instability as defined by Changes in Health, End-Stage Disease, Signs, and Symptoms Scale (CHESS) > 3, cognitive impairment by Cognitive Performance Scale (CPS) > 2, and functional disability was measured using the Activities of Daily Living Hierarchy Scale (ADLH) ≥5. Of the 3759 eligible residents, 2175 (57.9%) used at least 1 PCM. The prevalence of the 4 groups of PCM: OAC, PAI, AHT and LMA were 5.6%, 34.9%, 35.7%, and 10.4%, respectively. PCM use was lower in long-stay residents versus mid-stay: 56.0% vs. 62.7%, in cognitively impaired residents (47.1% vs. 67%), in residents with a high mortality risk (47.4% vs. 58.6%), and in residents with a high ADLH score (48.6% vs 64.0%). Although the prevalence of PCM use was lower in long-stay, cognitively impaired residents, persons with a high mortality risk, and residents with more functional disabilities, there seems to be room for deprescribing. Copyright © 2017 AMDA – The Society for Post-Acute and Long-Term Care Medicine. Published by Elsevier Inc. All rights reserved.

Development of paracetamol-caffeine co-crystals to improve compressional, formulation and in vivo performance.

PubMed

Latif, Sumera; Abbas, Nasir; Hussain, Amjad; Arshad, Muhammad Sohail; Bukhari, Nadeem Irfan; Afzal, Hafsa; Riffat, Sualeha; Ahmad, Zeeshan

2018-07-01

Paracetamol, a frequently used antipyretic and analgesic drug, has poor compression moldability owing to its low plasticity. In this study, new co-crystals of paracetamol (PCM) with caffeine (as a co-former) were prepared and delineated. Co-crystals exhibited improved compaction and mechanical behavior. A screening study was performed by utilizing a number of methods namely dry grinding, liquid assisted grinding (LAG), solvent evaporation (SE), and anti-solvent addition using various weight ratios of starting materials. LAG and SE were found successful in the screening study. Powders at 1:1 and 2:1 weight ratio of PCM/CAF by LAG and SE, respectively, resulted in the formation of co-crystals. Samples were characterized by PXRD, DSC, and ATR-FTIR techniques. Compressional properties of PCM and developed co-crystals were analyzed by in-die heckle model. Mean yield pressure (Py), an inverse measure of plasticity, obtained from the heckle plots decreased significantly (p < .05) for co-crystals than pure drug. Intrinsic dissolution profile of co-crystals showed up to 2.84-fold faster dissolution than PCM and physical mixtures in phosphate buffer pH 6.8 at 37 °C. In addition, co-crystals formulated into tablets by direct compression method showed better mechanical properties like hardness and tensile strength. In vitro dissolution studies on tablets also showed enhanced dissolution profiles (∼90-97%) in comparison to the tablets of PCM prepared by direct compression (∼55%) and wet granulation (∼85%) methods. In a single dose sheep model study, co-crystals showed up to twofold increase in AUC and C max . A significant (p < .05) decrease in clearance as compared to pure drug was also recorded. In conclusion, new co-crystals of PCM were successfully prepared with improved tabletability in vitro and in vivo profile. Enhancement in AUC and C max of PCM by co-crystallization might suggest the dose reduction and avoidance of side effects.

Phase-change materials for non-volatile memory devices: from technological challenges to materials science issues

NASA Astrophysics Data System (ADS)

Noé, Pierre; Vallée, Christophe; Hippert, Françoise; Fillot, Frédéric; Raty, Jean-Yves

2018-01-01

Chalcogenide phase-change materials (PCMs), such as Ge-Sb-Te alloys, have shown outstanding properties, which has led to their successful use for a long time in optical memories (DVDs) and, recently, in non-volatile resistive memories. The latter, known as PCM memories or phase-change random access memories (PCRAMs), are the most promising candidates among emerging non-volatile memory (NVM) technologies to replace the current FLASH memories at CMOS technology nodes under 28 nm. Chalcogenide PCMs exhibit fast and reversible phase transformations between crystalline and amorphous states with very different transport and optical properties leading to a unique set of features for PCRAMs, such as fast programming, good cyclability, high scalability, multi-level storage capability, and good data retention. Nevertheless, PCM memory technology has to overcome several challenges to definitively invade the NVM market. In this review paper, we examine the main technological challenges that PCM memory technology must face and we illustrate how new memory architecture, innovative deposition methods, and PCM composition optimization can contribute to further improvements of this technology. In particular, we examine how to lower the programming currents and increase data retention. Scaling down PCM memories for large-scale integration means the incorporation of the PCM into more and more confined structures and raises materials science issues in order to understand interface and size effects on crystallization. Other materials science issues are related to the stability and ageing of the amorphous state of PCMs. The stability of the amorphous phase, which determines data retention in memory devices, can be increased by doping the PCM. Ageing of the amorphous phase leads to a large increase of the resistivity with time (resistance drift), which has up to now hindered the development of ultra-high multi-level storage devices. A review of the current understanding of all these issues is provided from a materials science point of view.

Co-culture of chondrons and mesenchymal stromal cells reduces the loss of collagen VI and improves extracellular matrix production.

PubMed

Owida, H A; De Las Heras Ruiz, T; Dhillon, A; Yang, Y; Kuiper, N J

2017-12-01

Adult articular chondrocytes are surrounded by a pericellular matrix (PCM) to form a chondron. The PCM is rich in hyaluronan, proteoglycans, and collagen II, and it is the exclusive location of collagen VI in articular cartilage. Collagen VI anchors the chondrocyte to the PCM. It has been suggested that co-culture of chondrons with mesenchymal stromal cells (MSCs) might enhance extracellular matrix (ECM) production. This co-culture study investigates whether MSCs help to preserve the PCM and increase ECM production. Primary bovine chondrons or chondrocytes or rat MSCs were cultured alone to establish a baseline level for ECM production. A xenogeneic co-culture monolayer model using rat MSCs (20, 50, and 80%) was established. PCM maintenance and ECM production were assessed by biochemical assays, immunofluorescence, and histological staining. Co-culture of MSCs with chondrons enhanced ECM matrix production, as compared to chondrocyte or chondron only cultures. The ratio 50:50 co-culture of MSCs and chondrons resulted in the highest increase in GAG production (18.5 ± 0.54 pg/cell at day 1 and 11 ± 0.38 pg/cell at day 7 in 50:50 co-culture versus 16.8 ± 0.61 pg/cell at day 1 and 10 ± 0.45 pg/cell at day 7 in chondron monoculture). The co-culture of MSCs with chondrons appeared to decelerate the loss of the PCM as determined by collagen VI expression, whilst the expression of high-temperature requirement serine protease A1 (HtrA1) demonstrated an inverse relationship to that of the collagen VI. Together, this implies that MSCs directly or indirectly inhibited HtrA1 activity and the co-culture of MSCs with chondrons enhanced ECM synthesis and the preservation of the PCM.

Direct Digital Modulation Converter (DDMC)

DTIC Science & Technology

1976-01-01

the four different PCM channel banks: the D-l, TD968, TD660 and the European sys - tem. In Chapter 2, the computer simulation of the CVSD and of the...nave nafe nane nasse nabe nache nase nate rique eise clfe cide cipe cisse die eigne sime cive cive else lofe löge lome lone loce logue lobe lote...to cf ’&. snV A ^Y i^Y sY P*’ 13 10 co icr O u u diO KJ - < ’o cT dg ROTH^ l<^1 P/i 8 i c« i%sl X _ § I ■C CO C

Co-translational protein targeting facilitates centrosomal recruitment of PCNT during centrosome maturation in vertebrates

PubMed Central

Mahe, Karan; Ou, Tingyoung; Castro, Noemi M; Christensen, Lana N; Cheung, Lee; Jiang, Xueer; Yoon, Daniel; Huang, Bo

2018-01-01

As microtubule-organizing centers of animal cells, centrosomes guide the formation of the bipolar spindle that segregates chromosomes during mitosis. At mitosis onset, centrosomes maximize microtubule-organizing activity by rapidly expanding the pericentriolar material (PCM). This process is in part driven by the large PCM protein pericentrin (PCNT), as its level increases at the PCM and helps recruit additional PCM components. However, the mechanism underlying the timely centrosomal enrichment of PCNT remains unclear. Here, we show that PCNT is delivered co-translationally to centrosomes during early mitosis by cytoplasmic dynein, as evidenced by centrosomal enrichment of PCNT mRNA, its translation near centrosomes, and requirement of intact polysomes for PCNT mRNA localization. Additionally, the microtubule minus-end regulator, ASPM, is also targeted co-translationally to mitotic spindle poles. Together, these findings suggest that co-translational targeting of cytoplasmic proteins to specific subcellular destinations may be a generalized protein targeting mechanism. PMID:29708497

Experimental process investigation of a latent heat energy storage system with a staggered heat exchanger with different phase change materials for solar thermal energy storage applications

NASA Astrophysics Data System (ADS)

Tsolakoglou, Nikolas P.; Koukou, Maria K.; Vrachopoulos, Michalis Gr.; Tachos, Nikolaos; Lymberis, Kostas; Stathopoulos, Vassilis

2017-11-01

This work investigates melting and solidification processes of four different Phase Change Materials (PCM) used as latent heat thermal storage system. The experimental rig was consisted of an insulated tank, filled with the under investigation PCM, a staggered heat exchanger to supply or extract heat from the PCM cavity and a water pump to circulate Heat Transfer Fluid (HTF). Both charging (melting) and discharging (solidification) processes were conducted for two different HTF flow rates. The main scope of this work was to develop a first approach and to investigate the behaviour of PCM under various load conditions (different HTF flow rates). Results show that different HTF flow rates affect melting and solidification time periods; in both processes time was reduced while HTF flow rate was increased but in differentways due to the transition from conduction to convection heat transfer mechanisms.

Verification and Validation of EnergyPlus Phase Change Material Model for Opaque Wall Assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tabares-Velasco, P. C.; Christensen, C.; Bianchi, M.

2012-08-01

Phase change materials (PCMs) represent a technology that may reduce peak loads and HVAC energy consumption in buildings. A few building energy simulation programs have the capability to simulate PCMs, but their accuracy has not been completely tested. This study shows the procedure used to verify and validate the PCM model in EnergyPlus using a similar approach as dictated by ASHRAE Standard 140, which consists of analytical verification, comparative testing, and empirical validation. This process was valuable, as two bugs were identified and fixed in the PCM model, and version 7.1 of EnergyPlus will have a validated PCM model. Preliminarymore » results using whole-building energy analysis show that careful analysis should be done when designing PCMs in homes, as their thermal performance depends on several variables such as PCM properties and location in the building envelope.« less

The usage of phase change materials in fire fighter protective clothing: its effect on thermal protection

NASA Astrophysics Data System (ADS)

Zhao, Mengmeng

2017-12-01

The thermal protective performance of the fire fighter protective clothing is of vital importance for fire fighters. In the study fabrics treated by phase change materials (PCMs) were applied in the multi-layered fabrics of the fire fighter protective clothing ensemble. The PCM fabrics were placed at the different layers of the clothing and their thermal protective performance were measured by a TPP tester. Results show that with the application of the PCM fabrics the thermal protection of the multi-layered fabrics was greatly increased. The time to reach a second degree burn was largely reduced. The location of the PCM fabrics at the different layers did not affect much on the thermal protective performance. The higher amount of the PCM adds on, the higher thermal protection was brought. The fabrics with PCMs of a higher melting temperature could contribute to higher thermal protection.

Adhesion properties of Lactobacillus rhamnosus mucus-binding factor to mucin and extracellular matrix proteins.

PubMed

Nishiyama, Keita; Nakamata, Koichi; Ueno, Shintaro; Terao, Akari; Aryantini, Ni Putu Desy; Sujaya, I Nengah; Fukuda, Kenji; Urashima, Tadasu; Yamamoto, Yuji; Mukai, Takao

2015-01-01

We previously described potential probiotic Lactobacillus rhamnosus strains, isolated from fermented mare milk produced in Sumbawa Island, Indonesia, which showed high adhesion to porcine colonic mucin (PCM) and extracellular matrix (ECM) proteins. Recently, mucus-binding factor (MBF) was found in the GG strain of L. rhamnosus as a mucin-binding protein. In this study, we assessed the ability of recombinant MBF protein from the FSMM22 strain, one of the isolates of L. rhamnosus from fermented Sumbawa mare milk, to adhere to PCM and ECM proteins by overlay dot blot and Biacore assays. MBF bound to PCM, laminin, collagen IV, and fibronectin with submicromolar dissociation constants. Adhesion of the FSMM22 mbf mutant strain to PCM and ECM proteins was significantly less than that of the wild-type strain. Collectively, these results suggested that MBF contribute to L. rhamnosus host colonization via mucin and ECM protein binding.

Computational Fluid Dynamic Analysis of Enhancing Passenger Cabin Comfort Using PCM

NASA Astrophysics Data System (ADS)

Purusothaman, M.; Valarmathi, T. N.; Dada Mohammad, S. K.

2016-09-01

The main purpose of this study is to determine a cost effective way to enhance passenger cabin comfort by analyzing the effect of solar radiation of a open parked vehicle, which is exposed to constant solar radiation on a hot and sunny day. Maximum heat accumulation occurs in the car cabin due to the solar radiation. By means of computational fluid dynamics (CFD) analysis, a simulation process is conducted for the thermal regulation of the passenger cabin using a layer of phase change material (PCM) on the roof structure of a stationary car when exposed to ambient temperature on a hot sunny day. The heat energy accumulated in the passenger cabin is absorbed by a layer of PCM for phase change process. The installation of a ventilation system which uses an exhaust fan to create a natural convection scenario in the cabin is also considered to enhance passenger comfort along with PCM.

On numerical model of one-dimensional time-dependent gas flows through bed of encapsulated phase change material

NASA Astrophysics Data System (ADS)

Lutsenko, N. A.; Fetsov, S. S.

2017-10-01

Mathematical model and numerical method are proposed for investigating the one-dimensional time-dependent gas flows through a packed bed of encapsulated Phase Change Material (PCM). The model is based on the assumption of interacting interpenetrating continua and includes equations of state, continuity, momentum conservation and energy for PCM and gas. The advantage of the method is that it does not require predicting the location of phase transition zone and can define it automatically as in a usual shock-capturing method. One of the applications of the developed numerical model is the simulation of novel Adiabatic Compressed Air Energy Storage system (A-CAES) with Thermal Energy Storage subsystem (TES) based on using the encapsulated PCM in packed bed. Preliminary test calculations give hope that the method can be effectively applied in the future for modelling the charge and discharge processes in such TES with PCM.

Development of form stable Poly(methyl methacrylate) (PMMA) coated thermal phase change material for solar water heater applications

NASA Astrophysics Data System (ADS)

Munusamy, Y.; Shanmugam, S.; Shi-Ying, Kee

2018-04-01

Phase change material (PCM) is one of the most popular and widely used thermal energy storage material in solar water heater because it able to absorb and release a large amount of latent heat during a phase change process over a narrow temperature range. However the practical application of PCM is limited by two major issues; 1) leakage which leads to material loss and corrosion of tank and 2) large volume change during phase change process which cause pressure build up in the tank. In this work, form-stable PCM was prepared by coating myristic acid with Poly(methyl methacrylate) (PMMA) to prevent leakage of PCM. PMMA was mixed with different weight percentage (0.1, 0.2, 0.3, 0.4 and 0.5 wt%) of dicumyl peroxide (DCP). The purpose of adding DCP to PMMA is to crosslink the polymer and to increase the mechanical strength of PMMA to hold the myristic acid content inside the coating during the phase change process. Leakage test results showed that PMMA mixed with 0.1% DCP exhibit 0% leakage. This result is further supported by Field Emission Scanning Electron Microscopy (FESEM) images and Fourier transform infrared spectroscopy (FTIR) analysis results, where a compact and uniform coating without cracks were formed for PCM coated with PMMA with 0.1% DCP. Differential scanning calorimetry (DSC) results shows that the melting point of form-stable PCM is 55°C, freezing point is 50°C, the latent heat of melting and freezing is 67.59 J/g.

Three-dimensional finite element modeling of pericellular matrix and cell mechanics in the nucleus pulposus of the intervertebral disk based on in situ morphology.

PubMed

Cao, Li; Guilak, Farshid; Setton, Lori A

2011-02-01

Nucleus pulposus (NP) cells of the intervertebral disk (IVD) have unique morphological characteristics and biologic responses to mechanical stimuli that may regulate maintenance and health of the IVD. NP cells reside as single cell, paired or multiple cells in a contiguous pericellular matrix (PCM), whose structure and properties may significantly influence cell and extracellular matrix mechanics. In this study, a computational model was developed to predict the stress-strain, fluid pressure and flow fields for cells and their surrounding PCM in the NP using three-dimensional (3D) finite element models based on the in situ morphology of cell-PCM regions of the mature rat NP, measured using confocal microscopy. Three-dimensional geometries of the extracellular matrix and representative cell-matrix units were used to construct 3D finite element models of the structures as isotropic and biphasic materials. In response to compressive strain of the extracellular matrix, NP cells and PCM regions were predicted to experience volumetric strains that were 1.9-3.7 and 1.4-2.1 times greater than the extracellular matrix, respectively. Volumetric and deviatoric strain concentrations were generally found at the cell/PCM interface, while von Mises stress concentrations were associated with the PCM/extracellular matrix interface. Cell-matrix units containing greater cell numbers were associated with higher peak cell strains and lower rates of fluid pressurization upon loading. These studies provide new model predictions for micromechanics of NP cells that can contribute to an understanding of mechanotransduction in the IVD and its changes with aging and degeneration.

Flat plate solar air heater with latent heat storage

NASA Astrophysics Data System (ADS)

Touati, B.; Kerroumi, N.; Virgone, J.

2017-02-01

Our work contains two parts, first is an experimental study of the solar air heater with a simple flow and forced convection, we can use thatlaste oneit in many engineering's sectors as solardrying, space heating in particular. The second part is a numerical study with ansys fluent 15 of the storage of part of this solar thermal energy produced,using latent heat by using phase change materials (PCM). In the experimental parts, we realize and tested our solar air heater in URER.MS ADRAR, locate in southwest Algeria. Where we measured the solarradiation, ambient temperature, air flow, thetemperature of the absorber, glasses and the outlet temperature of the solar air heater from the Sunrise to the sunset. In the second part, we added a PCM at outlet part of the solar air heater. This PCM store a part of the energy produced in the day to be used in peak period at evening by using the latent heat where the PCMs present a grateful storagesystem.A numerical study of the fusion or also named the charging of the PCM using ANSYS Fluent 15, this code use the method of enthalpies to solve the fusion and solidification formulations. Furthermore, to improve the conjugate heat transfer between the heat transfer fluid (Air heated in solar plate air heater) and the PCM, we simulate the effect of adding fins to our geometry. Also, four user define are write in C code to describe the thermophysicalpropriety of the PCM, and the inlet temperature of our geometry which is the temperature at the outflow of the solar heater.

Study on solid liquid interface heat transfer of PCM under simultaneous charging and discharging (SCD) in horizontal cylinder annulus

NASA Astrophysics Data System (ADS)

Omojaro, Adebola Peter; Breitkopf, Cornelia

2017-07-01

Heat transfer performance during the simultaneous charging and discharging (SCD) operation process for phase change materials (PCM) contained inside the annulus of concentric horizontal cylinder was investigated. In the experimental set-up, the PCM inside the annulus serves as the heat sink along with an externally imposed forced cooling air. The obtained time wise temperature profile was used to determine the effects of different heat fluxes and the imposed forced convection cooling on the melt fraction values and the transition shift time from the observed conduction to natural convection heat transfer patterns. Furthermore, non-dimensional analysis was presented for the heat transfer at the interface to enable generalizing the result. Comparison of the results show that the SCD operation mode establish the condition that enables much PCM phase transition time and thus longer time of large latent heat transfer effect than the Partial and non simultaneous operations. Analysis results show that the variation of the heat flux for the SCD mode did not change the dominance of the natural convection over conduction heat transfers in the PCM. However, it significantly influences the commencement/transition shift time and melting rate while higher heat fluxes yields melt fraction that was 38-63% more for investigated process time. Variation with different cooling air flow rate shows more influences on the melt fraction than on the mode of heat transfer occurring in the PCM during melting. Available non-SCD modes correlation was shown to be insufficient to accurately predict interface heat transfer for the SCD modes.

Paracoccidioidomycosis in patients with human immunodeficiency virus: review of 12 cases observed in an endemic region in Brazil.

PubMed

Paniago, Anamaria Mello Miranda; de Freitas, Ana Carolina Carli; Aguiar, Eliana Setti Albuquerque; Aguiar, José Ivan Albuquerque; da Cunha, Rivaldo Venâncio; Castro, Ana Rita Coimbra Motta; Wanke, Bodo

2005-10-01

To study the clinical characteristics of 12 patients with paracoccidioidomycosis (PCM) and human immunodeficiency virus (HIV) infection. The clinical manifestations, diagnosis, treatment, and outcome of PCM in 12 patients infected with HIV attended at a University Hospital of Mato Grosso do Sul, Brazil, were evaluated. All patients were men, mean age 36.1 years old, and 11 had a diagnosis other than PCM as the aids-defining illness. Lymph nodes were the organs most often involved (10 patients, 83.3%), followed by lung involvement, usually with an interstitial pattern (seven patients, 58.3%), papule-nodular skin lesions with central ulceration in six (50%) and ulcerated lesions of oral mucous membrane in five (41.6%) patients. Pleural involvement occurred in one patient who presented large pleural effusion beside a pathologic rib fracture caused by P. brasiliensis. Seven patients showed involvement in more than one extrapulmonary organ. In eight (66.6%) cases the diagnosis was established by direct microscopy of clinical specimens. All patients used trimethoprim-sulfamethoxazole and seven patients were also treated with amphotericin B. Eight patients died with progressive PCM manifestations. Our review demonstrates that PCM, an endemic systemic mycosis in Brazil, when associated with AIDS, behaves clinically as an opportunistic disease.

Oral paracoccidioidomycosis: Retrospective analysis of 55 Brazilian patients.

PubMed

Trindade, Aline Heloísa; Meira, Henrique Côrtes; Pereira, Igor Figueiredo; de Lacerda, Julio César Tanos; de Mesquita, Ricardo Alves; Santos, Vagner Rodrigues

2017-08-01

Paracoccidioidomycosis (PCM) is a rare fungal infection in the world, but endemic and acquired exclusively in Latin America, with the highest prevalence in South America and Brazil, particularly. Changes in oral cavity are common and constitute the first clinical manifestation in many patients. The aim of this study was to describe the prevalence of oral PCM and analyse the profile of the disease and patients. Retrospective research, consisting of information present in the medical records in the period 1998-2015, whose histopathological diagnosis was oral PCM. Fifty-five oral PCM cases were confirmed. Of these patients, 90.9% were males and 9.1% were females. The average age was 49.66 years and the most reported occupation was rural workers. The painful symptomatology was present in 61.82% of patients. Erythematous lesions were predominant in 73% of them. In single lesions (22 cases), the most common locations were jugal mucosa and tongue. In multiple involvement (30 cases), the most affected regions were lips, jugal mucosa and alveolar ridge. Epidemiology of PCM, was similar to several other studies, especially in Brazil. This is the most important fungal infection in Latin America and the recognition of oral lesions is extremely important, as is often the first and in many cases the only manifestation of the disease. © 2017 Blackwell Verlag GmbH.

Low-Energy Amorphization of Ti1Sb2Te5 Phase Change Alloy Induced by TiTe2 Nano-Lamellae

PubMed Central

Ding, Keyuan; Rao, Feng; Lv, Shilong; Cheng, Yan; Wu, Liangcai; Song, Zhitang

2016-01-01

Increasing SET operation speed and reducing RESET operation energy have always been the innovation direction of phase change memory (PCM) technology. Here, we demonstrate that ∼87% and ∼42% reductions of RESET operation energy can be achieved on PCM cell based on stoichiometric Ti1Sb2Te5 alloy, compared with Ge2Sb2Te5 and non-stoichiometric Ti0.4Sb2Te3 based PCM cells at the same size, respectively. The Ti1Sb2Te5 based PCM cell also shows one order of magnitude faster SET operation speed compared to that of the Ge2Sb2Te5 based one. The enhancements may be caused by substantially increased concentration of TiTe2 nano-lamellae in crystalline Ti1Sb2Te5 phase. The highly electrical conduction and lowly thermal dissipation of the TiTe2 nano-lamellae play a major role in enhancing the thermal efficiency of the amorphization, prompting the low-energy RESET operation. Our work may inspire the interests to more thorough understanding and tailoring of the nature of the (TiTe2)n(Sb2Te3)m pseudobinary system which will be advantageous to realize high-speed and low-energy PCM applications. PMID:27469931

Cnn dynamics drive centrosome size asymmetry to ensure daughter centriole retention in Drosophila neuroblasts.

PubMed

Conduit, Paul T; Raff, Jordan W

2010-12-21

Centrosomes comprise a pair of centrioles surrounded by an amorphous network of pericentriolar material (PCM). In certain stem cells, the two centrosomes differ in size, and this appears to be important for asymmetric cell division [1, 2]. In some cases, centrosome asymmetry is linked to centriole age because the older, mother centriole always organizes more PCM than the daughter centriole, thus ensuring that the mother centriole is always retained in the stem cell after cell division [3]. This has raised the possibility that an "immortal" mother centriole may help maintain stem cell fate [4, 5]. It is unclear, however, how centrosome size asymmetry is generated in stem cells. Here we provide compelling evidence that centrosome size asymmetry in Drosophila neuroblasts is generated by the differential regulation of Cnn incorporation into the PCM at mother and daughter centrioles. Shortly after centriole separation, mother and daughter centrioles organize similar amounts of PCM, but Cnn incorporation is then rapidly downregulated at the mother centriole, while it is maintained at the daughter centriole. This ensures that the daughter centriole maintains its PCM and so its position at the apical cortex. Thus, the daughter centriole, rather than an "immortal" mother centriole, is ultimately retained in these stem cells.

Low-Energy Amorphization of Ti1Sb2Te5 Phase Change Alloy Induced by TiTe2 Nano-Lamellae.

PubMed

Ding, Keyuan; Rao, Feng; Lv, Shilong; Cheng, Yan; Wu, Liangcai; Song, Zhitang

2016-07-29

Increasing SET operation speed and reducing RESET operation energy have always been the innovation direction of phase change memory (PCM) technology. Here, we demonstrate that ∼87% and ∼42% reductions of RESET operation energy can be achieved on PCM cell based on stoichiometric Ti1Sb2Te5 alloy, compared with Ge2Sb2Te5 and non-stoichiometric Ti0.4Sb2Te3 based PCM cells at the same size, respectively. The Ti1Sb2Te5 based PCM cell also shows one order of magnitude faster SET operation speed compared to that of the Ge2Sb2Te5 based one. The enhancements may be caused by substantially increased concentration of TiTe2 nano-lamellae in crystalline Ti1Sb2Te5 phase. The highly electrical conduction and lowly thermal dissipation of the TiTe2 nano-lamellae play a major role in enhancing the thermal efficiency of the amorphization, prompting the low-energy RESET operation. Our work may inspire the interests to more thorough understanding and tailoring of the nature of the (TiTe2)n(Sb2Te3)m pseudobinary system which will be advantageous to realize high-speed and low-energy PCM applications.

Optimization of the level and range of working temperature of the PCM in the gypsum-microencapsulated PCM thermal energy storage unit for summer conditions in Central Poland

NASA Astrophysics Data System (ADS)

Łapka, P.; Jaworski, M.

2017-10-01

In this paper thermal energy storage (TES) unit in a form of a ceiling panel made of gypsum-microencapsulated PCM composite with internal U-shaped channels was considered and optimal characteristics of the microencapsulated PCM were determined. This panel may be easily incorporated into, e.g., an office or residential ventilation system in order to reduce daily variations of air temperature during the summer without additional costs related to the consumption of energy for preparing air parameters to the desired level. For the purpose of the analysis of heat transfer in the panel, a novel numerical simulator was developed. The numerical model consists of two coupled parts, i.e., the 1D which deals with the air flowing through the U-shaped channel and the 3D which deals with heat transfer in the body of the panel. The computational tool was validated based on the experimental study performed on the special set-up. Using this tool an optimization of parameters of the gypsum-microencapsulated PCM composite was performed in order to determine its most appropriate properties for the application under study. The analyses were performed for averaged local summer conditions in Warsaw, Poland.

The BepiColombo Laser Altimeter (BeLA) power converter module (PCM): Concept and characterisation.

PubMed

Rodrigo, J; Gasquet, E; Castro, J-M; Herranz, M; Lara, L-M; Muñoz, M; Simon, A; Behnke, T; Thomas, N

2017-03-01

This paper presents the principal considerations when designing DC-DC converters for space instruments, in particular for the power converter module as part of the first European space laser altimeter: "BepiColombo Laser Altimeter" on board the European Space Agency-Japan Aerospace Exploration Agency (JAXA) mission BepiColombo. The main factors which determine the design of the DC-DC modules in space applications are printed circuit board occupation, mass, DC-DC converter efficiency, and environmental-survivability constraints. Topics included in the appropriated DC-DC converter design flow are hereby described. The topology and technology for the primary and secondary stages, input filters, transformer design, and peripheral components are discussed. Component selection and design trade-offs are described. Grounding, load and line regulation, and secondary protection circuitry (under-voltage, over-voltage, and over-current) are then introduced. Lastly, test results and characterization of the final flight design are also presented. Testing of the inrush current, the regulated output start-up, and the switching function of the power supply indicate that these performances are fully compliant with the requirements.

Thermal Vacuum Test of Ice as a Phase Change Material Integrated with a Radiator

NASA Technical Reports Server (NTRS)

Lee, Steve A.; Leimkuehler, Thomas O.; Stephan, Ryan; Le, Hung V.

2010-01-01

Water may be used as radiation shielding for Solar Particle Events (SPE) to protect crewmembers in the Lunar Electric Rover (LER). Because the water is already present for radiation protection, it could also provide a mass efficient solution to the vehicle's thermal control system. This water can be frozen by heat rejection from a radiator and used as a Phase Change Material (PC1V1) for thermal storage. Use of this water as a PCM can eliminate the need for a pumped fluid loop thermal control system as well as reduce the required size of the radiator. This paper describes the testing and analysis performed for the Rover Engineering Development Unit (REDU), a scaled-down version of a water PCM heat sink for the LER. The REDU was tested in a thermal-vacuum chamber at environmental temperatures similar to those of a horizontal radiator panel on the lunar surface. Testing included complete freeze and melt cycles along with scaled transient heat load profiles simulating a 24-hour day for the rover.

PCM-enhanced lime plasters for vernacular and contemporary architecture

NASA Astrophysics Data System (ADS)

Theodoridou, Magdalini; Kyriakou, Loucas; Ioannou, Ioannis

2016-04-01

In 1997, the European Union (EU) pledged to reduce the amount of greenhouse gas emissions by 20% below the levels of 1990 by the end of 2020. In recent years it has become evident that, in order to reach that goal, EU Member States must take measures to encourage sustainability in the building industry, which is a major energy consumer. Such measures should involve the use of innovative, environmentally friendly materials and methods in new constructions, as well as the renovation of existing properties by upgrading their current state of energy efficiency. Phase Change Materials (PCMs) have the ability to absorb and release thermal energy, in the form of latent heat, during the melting or solidifying processes respectively. Thus, they may be used as additives in the production of thermally efficient composite building materials. A PCM-enhanced plaster is a heat storage medium combining an appropriate PCM with a cementitious or non-cementitious matrix to produce a low-cost thermal storage material with structural and thermostatic properties. Although innovative technologies, such as PCMs, have certainly contributed to the boost in the evolution of the building materials industry in recent years, a significant proportion of these technologies and practices have not yet been fully exploited in materials based on traditional principles. This paper focuses on the design and production of novel cementless PCM-enhanced lime plasters, in line with the traditional production technology of lime composites. The new plasters are produced using either hydrated or natural hydraulic lime binder, crushed calcarenite sand (0-2 mm) and commercial microencapsulated PCM in powder form (5% w/w of solids). Results from comparative tests between reference mixtures and mixtures with the addition of PCM, carried out 28, 56 and 90 days after laboratory production, prove the potential of PCMs in enhancing the thermal performance of traditional lime-based composites. The modified composites have significantly lower (by 55%) thermal conductivity and increased (by almost 20%) specific heat capacity at 90 days after laboratory production. At the same time, even though porosity values are higher for the PCM-enhanced renders, compared to the reference mixtures, their capillary absorption coefficient is significantly reduced (up to 60%). This is of great importance in the case of renders and may well be an indication for better expected durability in the long-term. Regarding the mechanical properties of the laboratory composites, PCM addition seems to have a negative effect on the hydraulic plasters. In contrast, when PCM is added to the hydrated lime-based plaster, no change is observed for the flexural strength, while the compressive strength is notably improved (up to 36%). The apparently improved properties of the PCM-enhanced plasters render them particularly appropriate for application in southern European climatic conditions. Due to their compatibility with traditional substrate materials (e.g. natural stone), the aforementioned composites may be used not only in new contemporary structures, but also for the renovation and retrofitting of existing buildings. The lime-based nature of their matrix and their physico-mechanical properties further extend their applicability to listed and monumental buildings.

Long Duration Exposure Facility (LDEF) low temperature Heat Pipe Experiment Package (HEPP) flight results

NASA Technical Reports Server (NTRS)

Mcintosh, Roy; Mccreight, Craig; Brennan, Patrick J.

1993-01-01

The Low Temperature Heat Pipe Flight Experiment (HEPP) is a fairly complicated thermal control experiment that was designed to evaluate the performance of two different low temperature ethane heat pipes and a low-temperature (182 K) phase change material. A total of 390 days of continuous operation with an axially grooved aluminum fixed conductance heat pipe and an axially grooved stainless steel heat pipe diode was demonstrated before the data acquisition system's batteries lost power. Each heat pipe had approximately 1 watt applied throughout this period. The HEPP was not able to cool below 188.6 K during the mission. As a result, the preprogrammed transport test sequence which initiates when the PCM temperature drops below 180 K was never exercised, and transport tests with both pipes and the diode reverse mode test could not be run in flight. Also, because the melt temperature of the n-heptane PCM is 182 K, its freeze/thaw behavior could not be tested. Post-flight thermal vacuum tests and thermal analyses have indicated that there was an apparent error in the original thermal analyses that led to this unfortunate result. Post-flight tests have demonstrated that the performance of both heat pipes and the PCM has not changed since being fabricated more than 14 years ago. A summary of HEPP's flight data and post-flight test results are presented.

Fabrication of composite poly(d,l-lactide)/montmorillonite nanoparticles for controlled delivery of acetaminophen by solvent-displacement method using glass capillary microfluidics.

PubMed

Othman, Rahimah; Vladisavljević, Goran T; Thomas, Noreen L; Nagy, Zoltan K

2016-05-01

Paracetamol (PCM)-loaded composite nanoparticles (NPs) composed of a biodegradable poly(d,l-lactide) (PLA) polymer matrix filled with organically modified montmorillonite (MMT) nanoparticles were fabricated by antisolvent nanoprecipitation in a microfluidic co-flow glass capillary device. The incorporation of MMT in the polymer improved both the drug encapsulation efficiency and the drug loading, and extended the rate of drug release in simulated intestinal fluid (pH 7.4). The particle size increased on increasing both the drug loading and the concentration of MMT in the polymer matrix, and decreased on increasing the aqueous to organic flow rate ratio. The drug encapsulation efficiency in the NPs was higher at higher aqueous to organic flow rate ratio due to faster formation of the NPs. The PCM-loaded PLA NPs containing 2 wt% MMT in PLA prepared at an aqueous to organic flow rate ratio of 10 with an orifice size of 200 μm exhibited a spherical shape with a mean size of 296 nm, a drug encapsulation efficiency of 38.5% and a drug loading of 5.4%. The encapsulation of MMT and PCM in the NPs was confirmed by transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis and attenuated total reflection-Fourier transform infrared spectroscopy. Copyright © 2016 Elsevier B.V. All rights reserved.

[Psychosomatic aspects of protein-calorie malnutrition in early childhood in a tropical environment. Facts and hypotheses].

PubMed

Guedeney, A

1986-01-01

After a brief look at the clinical descriptions of marasmus and kwashiorkor, and a summary of the physiopathological concepts of these protein calorie malnutritions (PCM), the author looks at arguments which suggest there is a change in the mother-child relationship at the onset of PCM, excluding, however, those malnutritions which appear in conditions of famine or catastrophe. These arguments are drawn principally from studies done in Africa, and are based on clinical, sociological, and ethnopsychiatric data. The contributing factor of maternal depression and that of relational characteristics of the child are considered, and an analysis is made of how these factors might converge at the onset of PCM. The author attempts to demonstrate the important role of a psychomotor retardation in the tableau of psychological troubles which present themselves during the course of Kwashiorkor. The role and importance of weaning, of the separation and the psychomotor retardation in the genesis of the "situation of malnutrition" are discussed. Finally, a parallel is established between PCM and early psychosomatic syndromes observed in the west, principally the anorexias and insomnias during the first year of life. The point in common between these situations and PCM is perhaps the onset of conditions having an upsetting and distorting effect on the mother-child relationship. The family and the entourage use certain collective representations in Africa ("Nit-KuBon", "Tjid-a-Paxer") to try and explain the onset of PCM. The description of these traditional representations is utilized as a materialization, by the mother and the social group, of an alteration of the mother-child relationship, and can be compared to representations which play the same role in the west.

2014 Global Conference on Polymer and Composite Materials (PCM 2014)

NASA Astrophysics Data System (ADS)

2014-08-01

The 2014 Global Conference on Polymer and Composite Materials (PCM 2014) sponsored by Ningbo Adhesives and Products Industry Association, Shanghai Bonding Technology Association, Zhejiang Bonding Technology Association, Wuhan Bonding Technology Association, Hebei Bonding and Coatings Association and Polyurethane Industry Association was held from May 27 to May 29 2014 in Ningbo, China. The technical program consisted of 8 international keynote speakers, oral presentations, and a poster session. The conference also included an industrial exhibition where more than 50 companies displayed in their booths their most recent advanced products and services. The present issue of IOP Conference Series: Materials Science and Engineering (MSE) records the proceedings of PCM 2014 and contains 37 specially selected manuscripts submitted to PCM2014 conference. The electronic submission and handling of manuscripts via the conference website, including the selection of reviewers and evaluation of manuscripts, were identical to the procedures applied to manuscripts submitted as regular contributions for publication. The organization of this conference and the preparation of proceedings volumes would have been impossible without the tremendous efforts and dedication of many individuals, especially from Ms. Yin Pan, who oversaw the organization of the conference and the program; and a large team of reviewers with their timely submission of quality reports. We express our sincere thanks to all authors and presenters for their contributions. We also thank very much our sponsors for their generous support. The 2015 Global Conference on Polymer and Composite Materials (PCM2015) will be held in Beijing, China on May 16-18, 2015. Beijing, the capital of the People's Republic of China and one of the most populous cities in the world, will welcome to all participants for a renewed and vibrant conference. Prof. Dr. Esteban Broitman Linköping University, Sweden Editor in Chief — PCM2014

Ti-Sb-Te alloy: a candidate for fast and long-life phase-change memory.

PubMed

Xia, Mengjiao; Zhu, Min; Wang, Yuchan; Song, Zhitang; Rao, Feng; Wu, Liangcai; Cheng, Yan; Song, Sannian

2015-04-15

Phase-change memory (PCM) has great potential for numerous attractive applications on the premise of its high-device performances, which still need to be improved by employing a material with good overall phase-change properties. In respect to fast speed and high endurance, the Ti-Sb-Te alloy seems to be a promising candidate. Here, Ti-doped Sb2Te3 (TST) materials with different Ti concentrations have been systematically studied with the goal of finding the most suitable composition for PCM applications. The thermal stability of TST is improved dramatically with increasing Ti content. The small density change of T0.32Sb2Te3 (2.24%), further reduced to 1.37% for T0.56Sb2Te3, would greatly avoid the voids generated at phase-change layer/electrode interface in a PCM device. Meanwhile, the exponentially diminished grain size (from ∼200 nm to ∼12 nm), resulting from doping more and more Ti, enhances the adhesion between phase-change film and substrate. Tests of TST-based PCM cells have demonstrated a fast switching rate of ∼10 ns. Furthermore, because of the lower thermal conductivities of TST materials, compared with Sb2Te3-based PCM cells, T0.32Sb2Te3-based ones exhibit lower required pulse voltages for Reset operation, which largely decreases by ∼50% for T0.43Sb2Te3-based ones. Nevertheless, the operation voltages for T0.56Sb2Te3-based cells dramatically increase, which may be due to the phase separation after doping excessive Ti. Finally, considering the decreased resistance ratio, TixSb2Te3 alloy with x around 0.43 is proved to be a highly promising candidate for fast and long-life PCM applications.

Voice disorders in residual paracoccidioidomycosis in upper airways and digestive tract.

PubMed

da Costa, Ananda Dutra; Vargas, Amanda Pereira; Lucena, Marcia Mendonça; Ruas, Ana Cristina Nunes; Braga, Fernanda da Silva Santos; Bom-Braga, Mateus Pereira; Bom-Braga, Frederico Pereira; do Valle, Antonio Carlos Francesconi; Igreja, Ricardo Pereira; Valete-Rosalino, Cláudia Maria

Paracoccidioidomycosis (PCM) is a systemic mycosis of acute and chronic evolution, caused by species belonging to the genus Paracoccidioides. It is considered the most prevalent systemic endemic mycosis in Latin America, with cases in the tropical and subtropical regions. Residual PCM refers to the fibrotic scar sequelae resulting from the disease treatment which, when associated with collagen accumulation, leads to functional and anatomic alterations in the organs. The aim of this study was to evaluate the vocal function of patients with residual PCM in upper airways and digestive tract. We performed a cross-sectional study in 2010 in a cohort of 21 patients with residual PCM in upper airways and digestive tract. The average age was 49.48±9.1 years, and only two (9.5%) patients were female. The study was performed in the 1-113 month-period (median 27) after the end of drug treatment. Five (23.8%) patients had alterations in the larynx as a sequela of the disease. However, all patients had vocal changes in vocal auditory perceptual analysis by GRBASI scale. The computerized acoustic analysis using the software Vox Metria, showed that 11 patients (52.4%) presented alterations in jitter, 15 (71.4%) in shimmer, 8 (38.1%) in F0, 4 (19%) in glottal to noise excitation (GNE), 7 (33.3%) in the presence of noise and 12 (57.1%) in the presence of vibratory irregularity. The great frequency of alterations in residual PCM suggests that the patients in such phase could benefit from a multidisciplinary treatment, offering them integral monitoring of the disease, including speech rehabilitation after the PCM is healed. Copyright © 2017 Asociación Española de Micología. Publicado por Elsevier España, S.L.U. All rights reserved.

Substantial reductions in ambient PAHs pollution and lives saved as a co-benefit of effective long-term PM2.5 pollution controls.

PubMed

Kong, Shaofei; Yan, Qin; Zheng, Huang; Liu, Haibiao; Wang, Wei; Zheng, Shurui; Yang, Guowei; Zheng, Mingming; Wu, Jian; Qi, Shihua; Shen, Guofeng; Tang, Lili; Yin, Yan; Zhao, Tianliang; Yu, Huan; Liu, Dantong; Zhao, Delong; Zhang, Tao; Ruan, Jujun; Huang, Mingzhi

2018-05-01

Under great efforts in fighting against serious haze problem of China since 2013, decreasing of air pollutants especially for fine particles (PM 2.5 ) has been revealed for several key regions. This study tried to answer whether the reduction of PM 2.5 -bound polycyclic aromatic hydrocarbons (PAHs) was coincident with PM 2.5 because of long-term pollution control measures (PCM), and to assess source-oriented health risks associated with inhalation exposure to PAHs. Field measurements were carried out before and after the publishing of local air pollution protection plan for Nanjing, a mega-city in east China. Results indicated that the air quality was substantially improving, with a significant reduction in annual average PM 2.5 by 34%, and moreover, PM 2.5 -bound PAHs significantly reduced by 63% (p < 0.001). The remarkable reduction was mainly attributable to the change of emission sources, compared to the influence of atmospheric circulation patterns, surface meteorological conditions, and atmospheric chemical reaction. Four PAHs sources including coal combustion (CC), petroleum and oil burning (PO), wood burning (WB) and vehicle emission (VE) were identified. On an annual basis, contributions to ambient PM 2.5 -PAHs from WB, PO, CC and VE sources in the period before the action of control measures were 2.26, 2.20, 1.96 and 5.62 ng m -3 , respectively. They reduced to 1.09, 0.37, 1.31 and 1.77 ng m -3 for the four source types, with the reduction percentages as 51, 83, 33 and 68%, respectively. The estimated reduction in lifetime lung cancer risk was around 61%. The study that firstly assessed the health effects of PAHs reduction as a co-benefit raised by air PCM sustained for a long period is believed to be applicable and referential for other mega-cities around the world for assessing the benefits of PCM. Copyright © 2018 Elsevier Ltd. All rights reserved.

Synchronous oral paracoccidioidomycosis and pulmonary tuberculosis in an immunocompetent patient.

PubMed

Amorim Pellicioli, Ana Carolina; Neves-Silva, Rodrigo; Santos-Silva, Alan Roger; Vargas, Pablo Agustin; Lopes, Márcio Ajudarte

2015-06-01

Paracoccidioidomycosis (PCM) and tuberculosis (TB) are chronic granulomatous infectious diseases, in which the main form of contraction is through inhalation of the microorganism-Paracoccidioides brasiliensis and Mycobacterium tuberculosis. Oral involvement of PCM is observed in up to 70 % of the cases and usually presents clinically as ulcerations with granular surface showing tiny hemorrhagic areas. Oral presentation of TB is rare with prevalence smaller than 0.5 % of all cases. Clinical presentation of oral TB mainly consists of single ulcers with irregular limits and necrotic base. A 70-year-old immunocompetent man presented simultaneously oral PCM and pulmonary TB. Medical history revealed a previous diagnosis of pulmonary TB; however, even under treatment for TB, the patient remained with oral lesions and intense pulmonary fibrosis. The physician requested P. brasiliensis serological analysis, which resulted positive. Although the combination of PCM and TB has been reported in the literature, it is still considered an uncommon condition and their diagnosis may represent a challenge to healthcare professionals because of the similarity between their clinical and radiological presentations.

Preparation and Characterization of Inorganic PCM Microcapsules by Fluidized Bed Method

PubMed Central

Ushak, Svetlana; Cruz, M. Judith; Cabeza, Luisa F.; Grágeda, Mario

2016-01-01

The literature shows that inorganic phase change materials (PCM) have been very seldom microencapsulated, so this study aims to contribute to filling this research gap. Bischofite, a by-product from the non-metallic industry identified as having good potential to be used as inorganic PCM, was microencapsulated by means of a fluidized bed method with acrylic as polymer and chloroform as solvent, after compatibility studies of both several solvents and several polymers. The formation of bischofite and pure MgCl2·6H2O microcapsules was investigated and analyzed. Results showed an efficiency in microencapsulation of 95% could be achieved when using 2 min of fluidization time and 2 kg/h of atomization flow. The final microcapsules had excellent melting temperatures and enthalpy compared to the original PCM, 104.6 °C and 95 J/g for bischofite, and 95.3 and 118.3 for MgCl2·6H2O. PMID:28787823

Sustainable Retrofit of Residential Roofs Using Metal Roofing Panels, Thin-Film Photovoltaic Laminates, and PCM Heat Sink Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kosny, Jan; Miller, William A; Childs, Phillip W

2011-01-01

During September-October 2009, research teams representing Metal Construction Association (the largest North American trade association representing metal building manufacturers, builders, and material suppliers), CertainTeed (one of the largest U.S. manufacturers of thermal insulation and building envelope materials), Unisolar (largest U.S. producer of amorphous silicone photo-voltaic (PV) laminates), Phase Change Energy (manufacturer of bio-based PCM), and Oak Ridge National Laboratory (ORNL) installed three experimental attics utilizing different roof retrofit strategies in the ORNL campus. The main goal of this project was experimental evaluation of a newly-developed sustainable re-roofing technology utilizing amorphous silicone PV laminates integrated with metal roof and PCM heatmore » sink. The experimental attic with PV laminate was expected to work during the winter time as a passive solar collector with PCM storing solar heat, absorbed during the day, and increasing overall attic air temperature during the night.« less

Nanoscale cross-point diode array accessing embedded high density PCM

NASA Astrophysics Data System (ADS)

Wang, Heng; Liu, Yan; Liu, Bo; Gao, Dan; Xu, Zhen; Zhan, Yipeng; Song, Zhitang; Feng, Songlin

2017-08-01

The main bottlenecks in the development of current embedded phase change memory (PCM) technology are the current density and data storage density. In this paper, we present a PCM with 4F2 cross-point diode selector and blade-type bottom electrode contact (BEC). A blade TiN BEC with a cross-sectional area of 630 nm2 (10 nm × 63 nm) reduces the reset current down to about 750 μA. The optimized diode array could supply this 750 μA reset current at about 1.7 V and low off-current 1 × 10-4 μA at about -5.05 V. The on-off ratio of this device is 7.5 × 106. The proposed nanoscale PCM device simultaneously exhibits an operation voltage as low as 3 V and a high density drive current with an ultra small cell size of 4F2 (108 nm × 108 nm). Over 106 cycling endurance properties guarantee that it can work effectively on the embedded memory.

Numerical modelling of phase-change material used for PV panels cooling

NASA Astrophysics Data System (ADS)

Sellami, Assia; Elotmani, Rabie; Kandoussi, Khalid; Eljouad, Mohamed; Hajjaji, Abdelowahed; Boutaous, M'Hamed

2017-12-01

Passive cooling of a PV solar panel using phase-change material (PCM) may play an important role in increasing efficiency of PV cells. Because it does not need a maintenance and does not release greenhouses gases, PCM seems to be a good way to decrease the among of overheating of PV cell. The aims of this paper describes a detailed multiphysical issue in order to understand the effect of PCM (RT25) in keeping PV cell temperature close to ambient. The study is focused on modeling the heat and mass transfer in a PCM domain by modifying the buoyancy term in momentum equation. Due to a phase-change and free convection, transient incompressible flow is taken into account to explain the dynamic variations of the velocity profile and viscosity distribution. With standard condition of irradiation and heat flux on both sides of the PV panel, a melt front has been tracked by the energy equation, which gives a good argument for the temperature evolution during phase-change.

High temperature thermal energy storage, including a discussion of TES integrated into power plants

NASA Technical Reports Server (NTRS)

Turner, R. H.

1978-01-01

Storage temperatures of 260 C and above are considered. Basic considerations concerning energy thermal storage are discussed, taking into account general aspects of thermal energy storage, thermal energy storage integrated into power plants, thermal storage techniques and technical considerations, and economic considerations. A description of system concepts is provided, giving attention to a survey of proposed concepts, storage in unpressurized fluids, water storage in pressurized containers, the use of an underground lined cavern for water storage, a submerged thin insulated steel shell under the ocean containing pressurized water, gas passage through solid blocks, a rock bed with liquid heat transport fluid, hollow steel ingots, heat storage in concrete or sand, sand in a fluidized bed, sand poured over pipes, a thermal energy storage heat exchanger, pipes or spheres filled with phase change materials (PCM), macroencapsulated PCM with heat pipe concept for transport fluid, solid PCM removed from heat transfer pipes by moving scrapers, and the direct contact between PCM and transport fluid.

Parametric studies of phase change thermal energy storage canisters for Space Station Freedom

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.

1991-01-01

Phase Change Materials (PCM) canister parametric studies are discussed wherein the thermal-structural effects of changing various canister dimensions and contained PCM mass values are examined. With the aim of improving performance, 11 modified canister designs are analyzed and judged relative to a baseline design using five quantitative performance indicators. Consideration is also given to qualitative factors such as fabrication/inspection, canister mass production, and PCM containment redundancy. Canister thermal analyses are performed using the finite-difference based computer program NUCAM-2DV. Thermal-stresses are calculated using closed-form solutions and simplifying assumptions. Canister wall thickness, outer radius, length, and contained PCM mass are the parameters considered for this study. Results show that singular canister design modifications can offer improvements on one or two performance indicators. Yet, improvement in one indicator is often realized at the expense of another. This confirms that the baseline canister is well designed. However, two alternative canister designs, which incorporate multiple modifications, are presented that offer modest improvements in mass or thermal performance, respectively.

Thermophysical and heat transfer properties of phase change material candidate for waste heat transportation system

NASA Astrophysics Data System (ADS)

Kaizawa, Akihide; Maruoka, Nobuhiro; Kawai, Atsushi; Kamano, Hiroomi; Jozuka, Tetsuji; Senda, Takeshi; Akiyama, Tomohiro

2008-05-01

A waste heat transportation system trans-heat (TH) system is quite attractive that uses the latent heat of a phase change material (PCM). The purpose of this paper is to study the thermophysical properties of various sugars and sodium acetate trihydrate (SAT) as PCMs for a practical TH system and the heat transfer property between PCM selected and heat transfer oil, by using differential scanning calorimetry (DSC), thermogravimetry-differential thermal analysis (TG-DTA) and a heat storage tube. As a result, erythritol, with a large latent heat of 344 kJ/kg at melting point of 117°C, high decomposition point of 160°C and excellent chemical stability under repeated phase change cycles was found to be the best PCM among them for the practical TH system. In the heat release experiments between liquid erythritol and flowing cold oil, we observed foaming phenomena of encapsulated oil, in which oil droplet was coated by solidification of PCM.

Numerical and experimental analysis of heat pipes with application in concentrated solar power systems

NASA Astrophysics Data System (ADS)

Mahdavi, Mahboobe

Thermal energy storage systems as an integral part of concentrated solar power plants improve the performance of the system by mitigating the mismatch between the energy supply and the energy demand. Using a phase change material (PCM) to store energy increases the energy density, hence, reduces the size and cost of the system. However, the performance is limited by the low thermal conductivity of the PCM, which decreases the heat transfer rate between the heat source and PCM, which therefore prolongs the melting, or solidification process, and results in overheating the interface wall. To address this issue, heat pipes are embedded in the PCM to enhance the heat transfer from the receiver to the PCM, and from the PCM to the heat sink during charging and discharging processes, respectively. In the current study, the thermal-fluid phenomenon inside a heat pipe was investigated. The heat pipe network is specifically configured to be implemented in a thermal energy storage unit for a concentrated solar power system. The configuration allows for simultaneous power generation and energy storage for later use. The network is composed of a main heat pipe and an array of secondary heat pipes. The primary heat pipe has a disk-shaped evaporator and a disk-shaped condenser, which are connected via an adiabatic section. The secondary heat pipes are attached to the condenser of the primary heat pipe and they are surrounded by PCM. The other side of the condenser is connected to a heat engine and serves as its heat acceptor. The applied thermal energy to the disk-shaped evaporator changes the phase of working fluid in the wick structure from liquid to vapor. The vapor pressure drives it through the adiabatic section to the condenser where the vapor condenses and releases its heat to a heat engine. It should be noted that the condensed working fluid is returned to the evaporator by the capillary forces of the wick. The extra heat is then delivered to the phase change material through the secondary heat pipes. During the discharging process, secondary heat pipes serve as evaporators and transfer the stored energy to the heat engine. (Abstract shortened by ProQuest.).

Pulmonary Abnormalities in Mice with Paracoccidioidomycosis: A Sequential Study Comparing High Resolution Computed Tomography and Pathologic Findings

PubMed Central

Hidalgo, José Miguel; de Oliveira Pascarelli, Bernardo Miguel; Patiño, Jairo Hernando; Lenzi, Henrique Leonel; Restrepo, Angela; Cano, Luz Elena

2010-01-01

Background Human paracoccidioidomycosis (PCM) is an endemic fungal disease of pulmonary origin. Follow-up of pulmonary lesions by image studies in an experimental model of PCM has not been previously attempted. This study focuses on defining patterns, topography and intensity of lung lesions in experimentally infected PCM mice by means of a comparative analysis between High Resolution Computed Tomography (HRCT) and histopathologic parameters. Methodology Male BALB/c mice were intranasally inoculated with 3×106 Paracoccidioides brasiliensis (Pb) conidia (n = 50) or PBS (n = 50). HRCT was done every four weeks to determine pulmonary lesions, quantify lung density, reconstruct and quantify lung air structure. Lungs were also analyzed by histopathology and histomorphometry. Results Three different patterns of lesions were evidenced by HRCT and histopathology, as follows: nodular-diffuse, confluent and pseudo-tumoral. The lesions were mainly located around the hilus and affected more frequently the left lung. At the 4th week post-challenge HRCT showed that 80% of the Pb-infected mice had peri-bronchial consolidations associated with a significant increase in upper lung density when compared with controls, (−263±25 vs. −422±10 HU, p<0.001). After the 8th and 12th weeks, consolidation had progressed involving also the middle regions. Histopathology revealed that consolidation as assessed by HRCT was equivalent histologically to a confluent granulomatous reaction, while nodules corresponded to individual compact granulomas. At the 16th week of infection, confluent granulomas formed pseudotumoral masses that obstructed large bronchi. Discrete focal fibrosis was visible gradually around granulomas, but this finding was only evident by histopathology. Conclusions/Significance This study demonstrated that conventional HRCT is a useful tool for evaluation and quantification of pulmonary damage occurring in experimental mouse PCM. The experimental design used decreases the need to sacrifice a large number of animals, and serves to monitor treatment efficacy by means of a more rational approach to the study of human lung disease. PMID:20614019

Difficulty in diagnosing oral paracoccidioidomycosis after topical nystatin usage.

PubMed

Sperandio, Felipe Fornias; Giudice, Fernanda Salgueiredo; Coelho, Ana Patricia Carneiro Goncalves Bezerra; de Sousa, Suzana Cantanhede Orsini Machado; Martins, Marilia Triervelier

2012-01-01

Paracoccidioidomycosis (PCM) is caused by a dimorphic fungus called Paracoccidioides brasiliensis and is a disseminated, systemic disorder that involves the lungs and other organs but presents characteristic oral lesions as the prominent feature. This article reports an unusual case of a 56-year-old man who had symptomatic granulomatous lesions in the oral cavity. The patient had received a nystatin-based treatment that masked the presence of fungi and made the diagnosis of PCM difficult. Although nystatin is normally used to treat oral fungal infections such as candidiasis, its topical usage is not appropriate for management of PCM. Once the patient received the correct treatment, he demonstrated a full recovery.

Amphotericin B lipid complex in the treatment of severe paracoccidioidomycosis: a case series.

PubMed

Peçanha, Paulo Mendes; de Souza, Stella; Falqueto, Aloísio; Grão-Veloso, Tânia Regina; Lírio, Ludmila Ventura; Ferreira, Carlos Urbano Gonçalves; Santos, Aline Rocha; Costa, Hélbia Garcia; de Souza, Lúcia Renata Meirelles; Tuon, Felipe Francisco

2016-10-01

Amphotericin B deoxycholate is the main option for intravenous (i.v.) treatment of severe paracoccidioidomycosis (PCM). This is the first report of amphotericin B lipid complex (ABLC) in the treatment of PCM. Among 28 patients, cure was achieved in all patients (100%) using ABLC. Mean and median daily doses of ABLC were 3.39 mg/kg/day and 3.35 mg/kg/day, respectively. ABLC may be a choice in the treatment of severe forms of PCM or when i.v. options are required. Copyright © 2016 Elsevier B.V. and International Society of Chemotherapy. All rights reserved.

Methanol in its own gravy. A PCM study for simulation of vibrational spectra.

PubMed

Billes, Ferenc; Mohammed-Ziegler, Ildikó; Mikosch, Hans

2011-05-07

For studying both hydrogen bond and dipole-dipole interactions between methanol molecules (self-association) the geometry of clusters of increasing numbers of methanol molecules (n = 1,2,3) were optimized and also their vibrational frequencies were calculated with quantum chemical methods. Beside these B3LYP/6-311G** calculations, PCM calculations were also done for all systems with PCM at the same quantum chemical method and basis set, for considering the effect of the liquid continuum on the cluster properties. Comparing the results, the measured and calculated infrared spectra are in good accordance. This journal is © the Owner Societies 2011

Coherent beam combination using self-phase locked stimulated Brillouin scattering phase conjugate mirrors with a rotating wedge for high power laser generation.

PubMed

Park, Sangwoo; Cha, Seongwoo; Oh, Jungsuk; Lee, Hwihyeong; Ahn, Heekyung; Churn, Kil Sung; Kong, Hong Jin

2016-04-18

The self-phase locking of a stimulated Brillouin scattering-phase conjugate mirror (SBS-PCM) allows a simple and scalable coherent beam combination of existing lasers. We propose a simple optical system composed of a rotating wedge and a concave mirror to overcome the power limit of the SBS-PCM. Its phase locking ability and the usefulness on the beam-combination laser are demonstrated experimentally. A four-beam combination is demonstrated using this SBS-PCM scheme. The relative phases between the beams were measured to be less than λ/24.7.

Thermal energy storage behaviour of nanoparticle enhanced PCM during freezing and melting

NASA Astrophysics Data System (ADS)

P, Murugan; P, Ganesh Kumar; V, Kumaresan; M, Meikandan; K, Malar Mohan; R, Velraj

2018-03-01

The present research work aimed to investigate the melting and solidification characteristics of NPCM. The NPCM was prepared using paraffin as the PCM and high conductive MWCNT as the nanomaterial without using any dispersant. The NPCM was prepared by dispersing MWCNTs with volume fractions of 0.3%, 0.6% and 0.9% in PCM as the base PCM. SEM morphology showed the uniform dispersion of MWCNTs in the paraffin wax. The MWCNT nano-additives PCMs showed two peaks in the heating curve by DSC measurement. Lessening in melting and solidification time of 30% and 43% was attained in the case of NPCM with 0.3% and 0.9%, respectively. It is observed from the DSC analysis that the latent heat of pure paraffin during freezing and melting cycle was 139.2 J/g (at 56.61 °C) and 131.8 J/g (at 57.55 °C), respectively. Whereas, the latent heat of NPCM with 0.9% of nanofluid was 150.7 J/g (at 56.36 °C) and 148.3 J/g (58.35 °C). It is construed that a maximum change in latent heat of 7.6% and 11% was observed between pure PCM and NPCM during freezing and melting cycle. For the lesser nanoparticle concentration (0.3% and 0.6%), the percentage change in latent heat was lesser than 0.9%.

Resonant-convergent PCM response theory for the calculation of second harmonic generation in makaluvamines A-V: pyrroloiminoquinone marine natural products from poriferans of genus Zyzzya.

PubMed

Milne, Bruce F; Norman, Patrick

2015-05-28

The first-order hyperpolarizability, β, has been calculated for a group of marine natural products, the makaluvamines. These compounds possess a common cationic pyrroloiminoquinone structure that is substituted to varying degrees. Calculations at the MP2 level indicate that makaluvamines possessing phenolic side chains conjugated with the pyrroloiminoquinone moiety display large β values, while breaking this conjugation leads to a dramatic decrease in the calculated hyperpolarizability. This is consistent with a charge-transfer donor-π-acceptor (D-π-A) structure type, characteristic of nonlinear optical chromophores. Dynamic hyperpolarizabilities calculated using resonance-convergent time-dependent density functional theory coupled to polarizable continuum model (PCM) solvation suggest that significant resonance enhancement effects can be expected for incident radiation with wavelengths around 800 nm. The results of the current work suggest that the pyrroloiminoquinone moiety represents a potentially useful new chromophore subunit, in particular for the development of molecular probes for biological imaging. The introduction of solvent-solute interactions in the theory is conventionally made in a density matrix formalism, and the present work will provide detailed account of the approximations that need to be introduced in wave function theory and our program implementation. The program implementation as such is achieved by a mere combination of existing modules from previous developments, and it is here only briefly reviewed.

Bone marrow necrosis related to paracoccidioidomycosis: the first eight cases identified at autopsy

PubMed Central

Resende, Lucilene S R; Mendes, Rinaldo P; Bacchi, Maura M; Marques, Sílvio A; Barraviera, Benedito; Souza, Lenice R; Meira, Domingos A; Niéro-Melo, Lígia

2009-01-01

Aims: To report the first eight bone marrow necrosis (BMN) cases related to paracoccidioidomycosis (PCM) from patient autopsies with well-documented bone marrow (BM) histology and cytology. Methods and results: A retrospective evaluation was performed on BM specimens from eight autopsied patients from Botucatu University Hospital with PCM-related BMN. Relevant BMN literature was searched and analysed. Conclusions: All eight patients had acute PCM. Six had histological only (biopsies) and two cytological only (smears) specimens. Five biopsy specimens revealed severe and one mild coagulation patterned necrotic areas. Five had osteonecrosis. The cytological specimens also showed typical BMN patterns. Paracoccidioides brasiliensis yeast forms were visible within necrotic areas in all cases. PMID:19309401

Role of mechanical stress in the resistance drift of Ge2Sb2Te5 films and phase change memories

NASA Astrophysics Data System (ADS)

Rizzi, M.; Spessot, A.; Fantini, P.; Ielmini, D.

2011-11-01

In a phase change memory (PCM), the device resistance increases slowly with time after the formation of the amorphous phase, thus affecting the stability of stored data. This work investigates the resistance drift in thin films of amorphous Ge2Sb2Te5 and in PCMs, demonstrating a common kinetic of drift in stressed/unstressed films and in the nanometer-size active volume of a PCM with different stress levels developed via stressor layers. It is concluded that stress is not the root cause of PCM drift, which is instead attributed to intrinsic structural relaxation due to the disordered, metastable nature of the amorphous chalcogenide phase.

Phase Change Material Thermal Power Generator

NASA Technical Reports Server (NTRS)

Jones, Jack A.

2013-01-01

An innovative modification has been made to a previously patented design for the Phase Change Material (PCM) Thermal Generator, which works in water where ocean temperature alternatively melts wax in canisters, or allows the wax to re-solidify, causing high-pressure oil to flow through a hydraulic generator, thus creating electricity to charge a battery that powers the vehicle. In this modification, a similar thermal PCM device has been created that is heated and cooled by the air and solar radiation instead of using ocean temperature differences to change the PCM from solid to liquid. This innovation allows the device to use thermal energy to generate electricity on land, instead of just in the ocean.

A Randomized Trial of Probation Case Management for Drug-Involved Women Offenders

ERIC Educational Resources Information Center

Guydish, Joseph; Chan, Monica; Bostrom, Alan; Jessup, Martha A.; Davis, Thomas B.; Marsh, Cheryl

2011-01-01

This article reports findings from a clinical trial of a probation case management (PCM) intervention for drug-involved women offenders. Participants were randomly assigned to PCM (n = 92) or standard probation (n = 91) and followed for 12 months using measures of substance abuse, psychiatric symptoms, social support, and service utilization.…

Evaluation of Probation Case Management (PCM) for Drug-Involved Women Offenders

ERIC Educational Resources Information Center

Chan, Monica; Guydish, Joseph; Prem, Rosemary; Jessup, Martha A.; Cervantes, Armando; Bostrom, Alan

2005-01-01

Based on availability of case management services, drug-involved women offenders entered either a probation case management (PCM) intervention(n = 65) or standard probation(n = 44). Participants were placed in the case management condition until all slots were filled, then placed in standard probation until case management slots opened.…

Thermal storage/discharge performances of Cu-Si alloy for solar thermochemical process

NASA Astrophysics Data System (ADS)

Gokon, Nobuyuki; Yamaguchi, Tomoya; Cho, Hyun-seok; Bellan, Selvan; Hatamachi, Tsuyoshi; Kodama, Tatsuya

2017-06-01

The present authors (Niigata University, Japan) have developed a tubular reactor system using novel "double-walled" reactor/receiver tubes with carbonate molten-salt thermal storage as a phase change material (PCM) for solar reforming of natural gas and with Al-Si alloy thermal storage as a PCM for solar air receiver to produce high-temperature air. For both of the cases, the high heat capacity and large latent heat (heat of solidification) of the PCM phase circumvents the rapid temperature change of the reactor/receiver tubes at high temperatures under variable and uncontinuous characteristics of solar radiation. In this study, we examined cyclic properties of thermal storage/discharge for Cu-Si alloy in air stream in order to evaluate a potentiality of Cu-Si alloy as a PCM thermal storage material. Temperature-increasing performances of Cu-Si alloy are measured during thermal storage (or heat-charge) mode and during cooling (or heat-discharge) mode. A oxidation state of the Cu-Si alloy after the cyclic reaction was evaluated by using electron probe micro analyzer (EPMA).

Geopolymer encapsulation of a chloride salt phase change material for high temperature thermal energy storage

NASA Astrophysics Data System (ADS)

Jacob, Rhys; Trout, Neil; Raud, Ralf; Clarke, Stephen; Steinberg, Theodore A.; Saman, Wasim; Bruno, Frank

2016-05-01

In an effort to reduce the cost and increase the material compatibility of encapsulated phase change materials (EPCMs) a new encapsulated system has been proposed. In the current study a molten salt eutectic of barium chloride (53% wt.), potassium chloride (28% wt.) and sodium chloride (19% wt.) has been identified as a promising candidate for low cost EPCM storage systems. The latent heat, melting point and thermal stability of the phase change material (PCM) was determined by DSC and was found to be in good agreement with results published in the literature. To cope with the corrosive nature of the PCM, it was decided that a fly-ash based geopolymer met the thermal and economic constraints for encapsulation. The thermal stability of the geopolymer shell was also tested with several formulations proving to form a stable shell for the chosen PCM at 200°C and/or 600°C. Lastly several capsules of the geopolymer shell with a chloride PCM were fabricated using a variety of methods with several samples remaining stable after exposure to 600°C testing.

Paracoccidioidomycosis in Mexico: clinical and epidemiological data from 93 new cases (1972-2012).

PubMed

López-Martínez, Rubén; Hernández-Hernández, Francisca; Méndez-Tovar, Luis Javier; Manzano-Gayosso, Patricia; Bonifaz, Alexandro; Arenas, Roberto; Padilla-Desgarennes, María Del Carmen; Estrada, Roberto; Chávez, Guadalupe

2014-09-01

Paracoccidioidomycosis (PCM) is an endemic systemic infection in several countries of Latin America. The few registered cases in Mexico most likely do not reflect the real frequency. Disseminate the epidemiological and clinical data of unreported cases of PCM in Mexico from 1972 until 2012 is the aim of this work. Epidemiological and clinical information of non-published cases of PCM was requested from the principal mycological diagnosis centres in Mexico. A total of 93 cases were received. The infection was found predominantly in men (95.7%), peasants (88.5%) and individual between 31 and 60 years of age. Most of the cases were found in tropical areas of the Gulf of Mexico (54.84%) and the Pacific littoral (20.3%). The main sites of dissemination were the oral mucosa (39.38%) and skin (34.05%). The most effective treatments were itraconazole alone and the combination of itraconazole with sulfamethoxazole-trimethoprim. PCM is a subdiagnosed pathology in Mexico. Therefore, adequate training is necessary to determine the current status of this mycosis. © 2014 Blackwell Verlag GmbH.

Marketing of Personalized Cancer Care on the Web: An Analysis of Internet Websites

PubMed Central

Cronin, Angel; Bair, Elizabeth; Lindeman, Neal; Viswanath, Vish; Janeway, Katherine A.

2015-01-01

Internet marketing may accelerate the use of care based on genomic or tumor-derived data. However, online marketing may be detrimental if it endorses products of unproven benefit. We conducted an analysis of Internet websites to identify personalized cancer medicine (PCM) products and claims. A Delphi Panel categorized PCM as standard or nonstandard based on evidence of clinical utility. Fifty-five websites, sponsored by commercial entities, academic institutions, physicians, research institutes, and organizations, that marketed PCM included somatic (58%) and germline (20%) analysis, interpretive services (15%), and physicians/institutions offering personalized care (44%). Of 32 sites offering somatic analysis, 56% included specific test information (range 1–152 tests). All statistical tests were two-sided, and comparisons of website content were conducted using McNemar’s test. More websites contained information about the benefits than limitations of PCM (85% vs 27%, P < .001). Websites specifying somatic analysis were statistically significantly more likely to market one or more nonstandard tests as compared with standard tests (88% vs 44%, P = .04). PMID:25745021

Design and Development of a Sub-Zero Fluid System for Demonstration of Orion's Phase Change Material Heat Exchangers on ISS

NASA Technical Reports Server (NTRS)

Sheth, Rubik B.; Ahlstrom, Thomas D.; Le, Hung V.

2016-01-01

NASA's Orion Multipurpose Crew Vehicle's Exploration Mission 2 is expected to loiter in Lunar orbit for a relatively long period of time. In low Lunar orbit (LLO) the thermal environment is cyclic - extremely cold in the eclipse and relatively hot near the subsolar point. Phase change material heat exchangers (PCM HXs) are the best option for long term missions in these environments. A PCM HX allows a vehicle to store excess waste energy by thawing a phase change material such as n-pentadecane wax. During portions of the orbit that are extremely cold, the excess energy is rejected, resolidifying the wax. Due to the inherent risk of compromising the heat exchanger during multiple freeze and thaw cycles, a unique payload was designed for the International Space Station to test and demonstration the functions of a PCM HX. The payload incorporates the use of a pumped fluid system and a thermoelectric heat exchanger to promote the freezing and thawing of the PCM HX. This paper shall review the design and development undertaken to build such a system.

Simulation and Experimental Study on Effect of Phase Change Material Thickness to Reduce Temperature of Photovoltaic Panel

NASA Astrophysics Data System (ADS)

Indartono, Y. S.; Prakoso, S. D.; Suwono, A.; Zaini, I. N.; Fernaldi, B.

2015-09-01

Solar energy is promising renewable energy which can be applied in Indonesia. Average solar radiation in the country is 4.8 kWh/day/m2. Weakness of silicon-based photovoltaic (PV) is efficiency reduction caused by temperature increase. Many attempts have been done to reduce PV temperature. In previous study, palm oil, which is widely available in Indonesia, is suitable to be used as phase change material (PCM) to reduce PV temperature. In this study, thickness of aluminium rectangular-tube containing phase change material oil is varied. The tube is placed at back part of PV. Numerical and experimental study was done to evaluate the effect of tube thickness to the temperature reduction of the PV. Variation of tube thickness used in the experiment is 50.8mm, 76.2 mm, 101.6 mm. Both studies show that increase of PCM thickness reduces PV temperature. Higher PCM thickness cause large reduction on PV temperature. Simulation result shows there is an optimum thickness of the PCM which is applied to the PV.

Clavibacter michiganensis subsp. michiganensis: first steps in the understanding of virulence of a Gram-positive phytopathogenic bacterium.

PubMed

Gartemann, Karl-Heinz; Kirchner, Oliver; Engemann, Jutta; Gräfen, Ines; Eichenlaub, Rudolf; Burger, Annette

2003-12-19

Clavibacter michiganensis subsp. michiganensis is a plant-pathogenic actinomycete. It infects tomato, spreads through the xylem and causes bacterial wilt and canker. The wild-type strain NCPPB382 carries two plasmids, pCM1 and pCM2. The cured plasmid-free derivative CMM100 is still able to colonize tomato, but no disease symptoms develop indicating that all genes required for successful infection, establishment and growth in the plant reside on the chromosome. Both plasmids carry one virulence factor, a gene encoding a cellulase, CelA in case of pCM1 and a putative serine protease Pat-1 on pCM2. These genes can independently convert the non-virulent strain CMM100 into a pathogen causing wilt on tomatoes. Currently, genome projects for Cmm and the closely related potato-pathogen C. michiganensis subsp. sepedonicus have been initiated. The data from the genome project shall give clues on further genes involved in plant-microbe interaction that can be tested experimentally. Especially, identification of genes related to host-specificity through genome comparison of the two subspecies might be possible.

GIAO-DFT calculation of 15 N NMR chemical shifts of Schiff bases: Accuracy factors and protonation effects.

PubMed

Semenov, Valentin A; Samultsev, Dmitry O; Krivdin, Leonid B

2018-02-09

15 N NMR chemical shifts in the representative series of Schiff bases together with their protonated forms have been calculated at the density functional theory level in comparison with available experiment. A number of functionals and basis sets have been tested in terms of a better agreement with experiment. Complimentary to gas phase results, 2 solvation models, namely, a classical Tomasi's polarizable continuum model (PCM) and that in combination with an explicit inclusion of one molecule of solvent into calculation space to form supermolecule 1:1 (SM + PCM), were examined. Best results are achieved with PCM and SM + PCM models resulting in mean absolute errors of calculated 15 N NMR chemical shifts in the whole series of neutral and protonated Schiff bases of accordingly 5.2 and 5.8 ppm as compared with 15.2 ppm in gas phase for the range of about 200 ppm. Noticeable protonation effects (exceeding 100 ppm) in protonated Schiff bases are rationalized in terms of a general natural bond orbital approach. Copyright © 2018 John Wiley & Sons, Ltd.

Numerical and Experimental Analysis on Inorganic Phase Change Material Usage in Construction

NASA Astrophysics Data System (ADS)

Muthuvel, S.; Saravanasankar, S.; Sudhakarapandian, R.; Muthukannan, M.

2014-12-01

This work demonstrates the significance of Phase Change Material (PCM) in the construction of working sheds and product storage magazines in fireworks industries to maintain less temperature variation by passive cooling. The inorganic PCM, namely Calcium Chloride Hexahydrate (CCH) is selected in this study. First, the performance of two models with inbuilt CCH was analysed, using computational fluid dynamics. A significant change in the variation of inner wall temperature was observed, particularly during the working hours. This is mainly due to passive cooling, where the heat transfer from the surroundings to the room is partially used for the phase change from solid to liquid. The experiment was carried out by constructing two models, one with PCM packed in hollow brick walls and roof, and the other one as a conventional construction. The experimental results show that the temperature of the room got significantly reduced up to 7 °C. The experimental analysis results had good agreement with the numerical analysis results, and this reveals the advantage of the PCM in the fireworks industry construction.

A phage display vector optimized for the generation of human antibody combinatorial libraries and the molecular cloning of monoclonal antibody fragments.

PubMed

Solforosi, Laura; Mancini, Nicasio; Canducci, Filippo; Clementi, Nicola; Sautto, Giuseppe Andrea; Diotti, Roberta Antonia; Clementi, Massimo; Burioni, Roberto

2012-07-01

A novel phagemid vector, named pCM, was optimized for the cloning and display of antibody fragment (Fab) libraries on the surface of filamentous phage. This vector contains two long DNA "stuffer" fragments for easier differentiation of the correctly cut forms of the vector. Moreover, in pCM the fragment at the heavy-chain cloning site contains an acid phosphatase-encoding gene allowing an easy distinction of the Escherichia coli cells containing the unmodified form of the phagemid versus the heavy-chain fragment coding cDNA. In pCM transcription of heavy-chain Fd/gene III and light chain is driven by a single lacZ promoter. The light chain is directed to the periplasm by the ompA signal peptide, whereas the heavy-chain Fd/coat protein III is trafficked by the pelB signal peptide. The phagemid pCM was used to generate a human combinatorial phage display antibody library that allowed the selection of a monoclonal Fab fragment antibody directed against the nucleoprotein (NP) of Influenza A virus.

Immunocytochemical localization of cytokines and inducible nitric oxide synthase (iNOS) in oral mucosa and lymph nodes of patients with paracoccidioidomycosis.

PubMed

Neworal, E P M; Altemani, A; Mamoni, R L; Noronha, I L; Blotta, M H S L

2003-03-07

Paracoccidioidomycosis (PCM) is a deep mycosis caused by Paracoccidioides brasiliensis, with high incidence in Brazil. In order to examine the immune response in lesional tissue from patients with PCM, we analyzed cytokines as well as the phenotype of the cell infiltrate. Paraffin-embedded tissue from the oral mucosa of eight patients with the localized adult form (AF) of PCM and from the lymph nodes of 10 patients with the juvenile form (JF) of PCM was analyzed by immunohistochemistry to detect tumor necrosis factor-alpha (TNF-alpha), inducible nitric oxide synthase (iNOS), transforming growth factor-beta (TGF-beta) and interleukin-10 (IL-10). Most of the inflammatory cells in the lymph nodes were CD68+ (macrophages, epithelioid and giant cells), while a mixed infiltrate with macrophages, plasma cells and neutrophils was detected in the oral mucosa. TNF-alpha as well as iNOS expression was similar in lymph nodes and oral mucosa, whereas TGF-beta and IL-10 were observed in a larger number of macrophages, epithelioid and giant cells in the lymph nodes, where numerous yeast cells were visualized. The higher expression of anti-inflammatory cytokines (IL-10 and TGF-beta) in lesions of patients with the JF of PCM (lymph nodes) may represent a mechanism by which the fungus evades the host immune response, contributing to a more severe and disseminated form of the disease.

Developing porous carbon with dihydrogen phosphate groups as sulfur host for high performance lithium sulfur batteries

NASA Astrophysics Data System (ADS)

Cui, Yanhui; Zhang, Qi; Wu, Junwei; Liang, Xiao; Baker, Andrew P.; Qu, Deyang; Zhang, Hui; Zhang, Huayu; Zhang, Xinhe

2018-02-01

Carbon matrix (CM) derived from biomass is low cost and easily mass produced, showing great potential as sulfur host for lithium sulfur batteries. In this paper we report on a dihydrogen phosphate modified CM (PCM-650) prepared from luffa sponge (luffa acutangula) by phosphoric acid treatment. The phosphoric acid not only increases the surface area of the PCM-650, but also introduces dihydrogen phosphate onto PCM-650 (2.28 at% P). Sulfur impregnated (63.6 wt%) PCM-650/S, in comparison with samples with less dihydrogen phosphate LPCM-650/S, shows a significant performance improvement. XPS analysis is conducted for sulfur at different stages, including sulfur (undischarged), polysulfides (discharge to 2.1 V) and short chain sulfides (discharge to 1.7 V). The results consistently show chemical shifts for S2p in PCM-650, suggesting an enhanced adsorption effect. Furthermore, density functional theory (DFT) calculations is used to clarify the molecular binding: carbon/sulfur (0.86 eV), carbon/Li2S (0.3 eV), CH3-O-PO3H2/sulfur (1.24 eV), and CH3-O-PO3H2/Li2S (1.81 eV). It shows that dihydrogen phosphate group can significantly enhance the binding with sulfur and sulfide, consistent with XPS results. Consequently a CM functionalised with dihydrogen phosphate shows great potential as the sulfur host in a Li-S battery.

Identification of men with low-risk biopsy-confirmed prostate cancer as candidates for active surveillance.

PubMed

Lin, Daniel W; Crawford, E David; Keane, Thomas; Evans, Brent; Reid, Julia; Rajamani, Saradha; Brown, Krystal; Gutin, Alexander; Tward, Jonathan; Scardino, Peter; Brawer, Michael; Stone, Steven; Cuzick, Jack

2018-06-01

A combined clinical cell-cycle risk (CCR) score that incorporates prognostic molecular and clinical information has been recently developed and validated to improve prostate cancer mortality (PCM) risk stratification over clinical features alone. As clinical features are currently used to select men for active surveillance (AS), we developed and validated a CCR score threshold to improve the identification of men with low-risk disease who are appropriate for AS. The score threshold was selected based on the 90th percentile of CCR scores among men who might typically be considered for AS based on NCCN low/favorable-intermediate risk criteria (CCR = 0.8). The threshold was validated using 10-year PCM in an unselected, conservatively managed cohort and in the subset of the same cohort after excluding men with high-risk features. The clinical effect was evaluated in a contemporary clinical cohort. In the unselected validation cohort, men with CCR scores below the threshold had a predicted mean 10-year PCM of 2.7%, and the threshold significantly dichotomized low- and high-risk disease (P = 1.2 × 10 -5 ). After excluding high-risk men from the validation cohort, men with CCR scores below the threshold had a predicted mean 10-year PCM of 2.3%, and the threshold significantly dichotomized low- and high-risk disease (P = 0.020). There were no prostate cancer-specific deaths in men with CCR scores below the threshold in either analysis. The proportion of men in the clinical testing cohort identified as candidates for AS was substantially higher using the threshold (68.8%) compared to clinicopathologic features alone (42.6%), while mean 10-year predicted PCM risks remained essentially identical (1.9% vs. 2.0%, respectively). The CCR score threshold appropriately dichotomized patients into low- and high-risk groups for 10-year PCM, and may enable more appropriate selection of patients for AS. Copyright © 2018 Elsevier Inc. All rights reserved.

Heat transfer characteristics of building walls using phase change material

NASA Astrophysics Data System (ADS)

Irsyad, M.; Pasek, A. D.; Indartono, Y. S.; Pratomo, A. W.

2017-03-01

Minimizing energy consumption in air conditioning system can be done with reducing the cooling load in a room. Heat from solar radiation which passes through the wall increases the cooling load. Utilization of phase change material on walls is expected to decrease the heat rate by storing energy when the phase change process takes place. The stored energy is released when the ambient temperature is low. Temperature differences at noon and evening can be utilized as discharging and charging cycles. This study examines the characteristics of heat transfer in walls using phase change material (PCM) in the form of encapsulation and using the sleeve as well. Heat transfer of bricks containing encapsulated PCM, tested the storage and released the heat on the walls of the building models were evaluated in this study. Experiments of heat transfer on brick consist of time that is needed for heat transfer and thermal conductivity test as well. Experiments were conducted on a wall coated by PCM which was exposed on a day and night cycle to analyze the heat storage and heat release. PCM used in these experiments was coconut oil. The measured parameter is the temperature at some points in the brick, walls and ambient temperature as well. The results showed that the use of encapsulation on an empty brick can increase the time for thermal heat transfer. Thermal conductivity values of a brick containing encapsulated PCM was lower than hollow bricks, where each value was 1.3 W/m.K and 1.6 W/m.K. While the process of heat absorption takes place from 7:00 am to 06:00 pm, and the release of heat runs from 10:00 pm to 7:00 am. The use of this PCM layer can reduce the surface temperature of the walls of an average of 2°C and slows the heat into the room.

Factors of influence upon the SF-36-based health related quality of life of patients following surgery for petroclival and lateral posterior surface of pyramid meningiomas.

PubMed

Pintea, B; Kandenwein, J A; Lorenzen, H; Boström, J P; Daher, F; Velazquez, V; Kristof, R A

2018-03-01

To describe the patient's self assessed health related quality of life (saHRQoL) based upon the medical outcome study 36-item short form health survey (SF-36) as well as the factors of influence upon the saHRQoL following surgery for petroclival (PCM) and lateral posterior surface of the pyramid (LPPM) meningiomas. In a series of 78 patients operated consecutively for PCM (n = 46) or LPPM (n = 32) the preoperative, intraoperative and postoperative data were collected retrospectively. The saHRQoL was obtained by mailing the SF-36 questionnaire to the patients. The SF-36 data of the whole patients group was compared with a healthy population. The SF-36 data of the PCM- and LPPM were compared to each other. The influence of pre-, intra- and postoperative findings upon the SF-36 was assessed by uni- and multifactorial analysis. 58 (69%) out of the 78 patients answered the SF-36 questionnaire at a median postoperative follow-up of 59 months. The patients, who answered the SF-36 questionnaire, had a significant lower perioperative complication rate than those who did not (46% vs. 75%, p = 0.019). The saHRQoL of the LPPM and PCM was reduced on several sub-scales, when compared to the German reference population. The outcome of PCM is, assessed by saHRQoL as well as by conventional neurosurgical grading scales, inferior to that of LPPM. The saHRQoL of LPPM correlated in the uni- and multivariate analysis with the early postoperative KPI on the sub-scales SF1 (physical functioning) and SF5 (vitality). Accordingly, the sub-scale SF2 (role-physical) of PCM correlated with the change of the KPI from preoperative to the last follow up. The saHRQoL of the evaluable patients was lower than that of the normal population. The saHRQoL score of PCM-patients was lower than that of LPPM-patients. For the future the saHRQol should be assessed routinely; It reflects the patients' perspective upon postoperative outcome and enables the comparison with other treatment modalities of these difficult to treat tumors. Copyright © 2018 Elsevier B.V. All rights reserved.

Risk factors associated with postcraniotomy meningitis: A retrospective study

PubMed Central

Chen, Chang-Hua; Chang, Chih-Yen; Lin, Li-Jhen; Chen, Wei Liang; Chang, Yu-Jun; Wang, Shu-Hui; Cheng, Chun-Yuan; Yen, Hua-Cheng

2016-01-01

Abstract Postcraniotomy meningitis (PCM) is a major challenge in neurosurgery, and changing patterns of infectious agents in PCM have been noted. The limited epidemiological data and urgent clinical needs motivated this research. We conducted this study to determine a risk assessment for PCM and the current pattern of infectious agents. We performed a retrospective case-control study of significant cases of postcraniotomy meningitis in the Changhua Christian Hospital System between January 1, 2008, and December 31, 2012. Postcraniotomy meningitis was diagnosed in 22 out of 4392 surgical patients; this data was reviewed for risk assessment. This study assessed the risk factors for postcraniotomy meningitis and found that it was more frequently seen in patients who were elderly (OR = 1.57, 95% CI = 1.32–2.98, P = 0.013), underwent emergency procedures (OR = 4.82, 95% CI = 1.50–14.53, P = 0.008), had leak of cerebrospinal fluid (OR = 4.62, 95% CI = 2.03–10.50, P = 0.012), had external ventricular drainage (OR = 4.68, 95% CI = 2.46–8.87, P = 0.006), were admitted to the intensive care unit (OR = 2.41, 95% CI = 1.53–8.08, P = 0.012), had used drain placement >72 hours (OR = 2.66, 95% CI = 1.04–4.29, P = 0.007), had surgery >4.5 hours (OR = 2.38, 95% CI = 1.39–4.05, P = 0.005), had repeat operations (OR = 2.74, 95% CI = 1.31–5.73, P = 0.018), endured trauma (OR = 5.97, 95% CI = 1.57–17.61, P = 0.007), or had 30-days mortality (OR = 5.07, 95% CI = 2.20–11.48, P = 0.001). The predominant pathogens isolated from cerebrospinal fluid were Staphylococcus aureus in 8 patients (36.7%) and Acinetobacter baumannii in 7 patients (31.8%). In our study, the mortality rate was 5.1% among all postcraniotomy patients. Accurate risk assessment, early diagnosis, and choice of appropriate antibiotics in accordance with epidemiologic information are the cornerstones of reducing mortality and morbidity in PCM. The changing pattern of infectious agents in PCM over time suggests the necessity of further studies to provide the most up-to-date insight to physicians. PMID:27495035

Some Considerations on the Partial Credit Model

ERIC Educational Resources Information Center

Verhelst, N. D.; Verstralen, H. H. F. M.

2008-01-01

The Partial Credit Model (PCM) is sometimes interpreted as a model for stepwise solution of polytomously scored items, where the item parameters are interpreted as difficulties of the steps. It is argued that this interpretation is not justified. A model for stepwise solution is discussed. It is shown that the PCM is suited to model sums of binary…

Methods for Assessing Item, Step, and Threshold Invariance in Polytomous Items Following the Partial Credit Model

ERIC Educational Resources Information Center

Penfield, Randall D.; Myers, Nicholas D.; Wolfe, Edward W.

2008-01-01

Measurement invariance in the partial credit model (PCM) can be conceptualized in several different but compatible ways. In this article the authors distinguish between three forms of measurement invariance in the PCM: step invariance, item invariance, and threshold invariance. Approaches for modeling these three forms of invariance are proposed,…

Interdisciplinary Science through the Parallel Curriculum Model: Lessons from the Sea

ERIC Educational Resources Information Center

Hathcock, Stephanie J.

2018-01-01

The Parallel Curriculum Model (PCM) lends itself to considering curriculum development from different angles. It begins with a solid Core Curriculum and can then be extended through the Curriculum of Connections, Practice, and Identity. This article showcases a way of thinking about the creation of a PCM unit by providing examples from an…

Mathematical modeling of moving boundary problems in thermal energy storage

NASA Technical Reports Server (NTRS)

Solomon, A. D.

1980-01-01

The capability for predicting the performance of thermal energy storage (RES) subsystems and components using PCM's based on mathematical and physical models is developed. Mathematical models of the dynamic thermal behavior of (TES) subsystems using PCM's based on solutions of the moving boundary thermal conduction problem and on heat and mass transfer engineering correlations are also discussed.

Simulated Aging and Characterization of Phase Change Materials for Thermal Management of Building Envelopes

DTIC Science & Technology

2015-09-01

materials of a PCM wall or ceiling panel. BioPCMat™ absorbs heat in the daytime and releases that heat during the night. The dimension of the typical...micrographs of Energain PCM samples showed evidence of melting and re- ERDC/CERL TR-15-23 32 crystallization ; however, there was no significant

Principal Leadership and School Culture with a School-Wide Implementation of Professional Crisis Management: A Redemptive v. Punitive Model

ERIC Educational Resources Information Center

Adams, Mark Thomas

2013-01-01

This qualitative study investigated the nature of the relationship between principal leadership and school culture within a school-wide implementation of Professional Crisis Management (PCM). PCM is a comprehensive and fully integrated system designed to manage crisis situations effectively, safely, and with dignity. While designed primarily to…

Using Paraffin PCM, Cryogel and TEC to Maintain Comet Surface Sample Cold from Earth Approach Through Retrieval

NASA Technical Reports Server (NTRS)

Choi, Michael K.

2017-01-01

An innovative thermal design concept to maintain comet surface samples cold (for example, 263 degrees Kelvin, 243 degrees Kelvin or 223 degrees Kelvin) from Earth approach through retrieval is presented. It uses paraffin phase change material (PCM), Cryogel insulation and thermoelectric cooler (TEC), which are commercially available.

Self-regulated transport in photonic crystals with phase-changing defects

NASA Astrophysics Data System (ADS)

Thomas, Roney; Ellis, Fred M.; Vitebskiy, Ilya; Kottos, Tsampikos

2018-01-01

Phase-changing materials (PCMs) are widely used for optical data recording, sensing, all-optical switching, and optical limiting. Our focus here is on the case when the change in transmission characteristics of the optical material is caused by the input light itself. Specifically, the light-induced heating triggers the phase transition in the PCM. In this paper, using a numerical example, we demonstrate that the incorporation of the PCM in a photonic structure can lead to a dramatic modification of the effects of light-induced phase transition, as compared to a stand-alone sample of the same PCM. Our focus is on short pulses. We discuss some possible applications of such phase-changing photonic structures for optical sensing and limiting.

Phase-change memory function of correlated electrons in organic conductors

NASA Astrophysics Data System (ADS)

Oike, H.; Kagawa, F.; Ogawa, N.; Ueda, A.; Mori, H.; Kawasaki, M.; Tokura, Y.

2015-01-01

Phase-change memory (PCM), a promising candidate for next-generation nonvolatile memories, exploits quenched glassy and thermodynamically stable crystalline states as reversibly switchable state variables. We demonstrate PCM functions emerging from a charge-configuration degree of freedom in strongly correlated electron systems. Nonvolatile reversible switching between a high-resistivity charge-crystalline (or charge-ordered) state and a low-resistivity quenched state, charge glass, is achieved experimentally via heat pulses supplied by optical or electrical means in organic conductors θ -(BEDT-TTF)2X . Switching that is one order of magnitude faster is observed in another isostructural material that requires faster cooling to kinetically avoid charge crystallization, indicating that the material's critical cooling rate can be useful guidelines for pursuing a faster correlated-electron PCM function.

A Review of the Experimental and Modeling Development of a Water Phase Change Heat Exchanger for Future Exploration Support Vehicles

NASA Technical Reports Server (NTRS)

Cognata, Thomas; Leimkuehler, Thomas; Ramaswamy, Balasubramaniam; Nayagam, Vedha; Hasan, Mohammad; Stephan, Ryan

2011-01-01

Water affords manifold benefits for human space exploration. Its properties make it useful for the storage of thermal energy as a Phase Change Material (PCM) in thermal control systems, in radiation shielding against Solar Particle Events (SPE) for the protection of crew members, and it is indisputably necessary for human life support. This paper envisions a single application for water which addresses these benefits for future exploration support vehicles and it describes recent experimental and modeling work that has been performed in order to arrive at a description of the thermal behavior of such a system. Experimental units have been developed and tested which permit the evaluation of the many parameters of design for such a system with emphasis on the latent energy content, temperature rise, mass, and interstitial material geometry. The experimental results are used to develop a robust and well correlated model which is intended to guide future design efforts toward the multi-purposed water PCM heat exchanger envisioned.

University of South Florida- Phase Change Materials (PCM)

ScienceCinema

Goswami, Yogi; Stefanakos, Lee

2018-05-30

USF is developing low-cost, high-temperature phase-change materials (PCMs) for use in thermal energy storage systems. Heat storage materials are critical to the energy storage process. In solar thermal storage systems, heat can be stored in these materials during the day and released at night--when the sun is not out--to drive a turbine and produce electricity. In nuclear storage systems, heat can be stored in these materials at night and released to produce electricity during daytime peak-demand hours. Most PCMs do not conduct heat very well. Using an innovative, electroless encapsulation technique, USF is enhancing the heat transfer capability of its PCMs. The inner walls of the capsules will be lined with a corrosion-resistant, high-infrared emissivity coating, and the absorptivity of the PCM will be controlled with the addition of nano-sized particles. USF's PCMs remain stable at temperatures from 600 to 1,000°C and can be used for solar thermal power storage, nuclear thermal power storage, and other applications.

Solvothermal method as a green chemistry solution for micro-encapsulation of phase change materials for high temperature thermal energy storage

NASA Astrophysics Data System (ADS)

Tudor, Albert Ioan; Motoc, Adrian Mihail; Ciobota, Cristina Florentina; Ciobota, Dan. Nastase; Piticescu, Radu Robert; Romero-Sanchez, Maria Dolores

2018-05-01

Thermal energy storage systems using phase change materials (PCMs) as latent heat storage are one of the main challenges at European level in improving the performances and efficiency of concentrated solar power energy generation due to their high energy density. PCM with high working temperatures in the temperature range 300-500 °C are required for these purposes. However their use is still limited due to the problems raised by the corrosion of the majority of high temperature PCMs and lower thermal transfer properties. Micro-encapsulation was proposed as one method to overcome these problems. Different micro-encapsulation methods proposed in the literature are presented and discussed. An original process for the micro-encapsulation of potassium nitrate as PCM in inorganic zinc oxide shells based on a solvothermal method followed by spray drying to produce microcapsules with controlled phase composition and distribution is proposed and their transformation temperatures and enthalpies measured by differential scanning calorimetry are presented.

Mirror-symmetric magneto-optical Kerr rotation using visible light in [(GeTe)2(Sb2Te3)1]n topological superlattices.

PubMed

Bang, Do; Awano, Hiroyuki; Tominaga, Junji; Kolobov, Alexander V; Fons, Paul; Saito, Yuta; Makino, Kotaro; Nakano, Takashi; Hase, Muneaki; Takagaki, Yukihiko; Giussani, Alessandro; Calarco, Raffaella; Murakami, Shuichi

2014-07-17

Interfacial phase change memory (iPCM), that has a structure of a superlattice made of alternating atomically thin GeTe and Sb2Te3 layers, has recently attracted attention not only due to its superior performance compared to the alloy of the same average composition in terms of energy consumption but also due to its strong response to an external magnetic field (giant magnetoresistance) that has been speculated to arise from switching between topological insulator (RESET) and normal insulator (SET) phases. Here we report magneto-optical Kerr rotation loops in the visible range, that have mirror symmetric resonances with respect to the magnetic field polarity at temperatures above 380 K when the material is in the SET phase that has Kramers-pairs in spin-split bands. We further found that this threshold temperature may be controlled if the sample was cooled in a magnetic field. The observed results open new possibilities for use of iPCM beyond phase-change memory applications.

Nimbus 4/IRLS Balloon Interrogation Package (BIP)

NASA Technical Reports Server (NTRS)

1971-01-01

The balloon interrogation package (BIP), an integral part of the overall interrogation, recording, and location subsystems (IRLS) for the Nimbus 4 program, is described. The BIP is a self-contained, integrated transponder designed to be carried aloft by a constant altitude, superpressure balloon to an altitude of 67,000 or 78,000 feet. After launch the BIP senses high-altitude balloon overpressure and temperature, and upon receipt of an interrogated command from the IRLS aboard the Nimbus 4 satellite, the BIP enodes the data on a real-time basis into a pulse-code modulation (PCM) format and transmits this data to the satellite. A summary of the program activity to produce 30 BIP systems and to support balloon launches from Ascension Island is presented.

Recent Patents on Nano-Enhanced Materials for Use in Thermal Energy Storage (TES).

PubMed

Ferrer, Gerard; Barreneche, Camila; Solé, Aran; Juliá, José Enrique; Cabeza, Luisa F

2017-07-10

Thermal energy storage (TES) systems using phase change materials (PCM) have been lately studied and are presented as one of the key solutions for the implementation of renewable energies. These systems take advantage of the latent heat of phase change of PCM during their melting/ solidification processes to store or release heat depending on the needs and availability. Low thermal conductivity and latent heat are the main disadvantages of organic PCM, while corrosion, subcooling and thermal stability are the prime problems that inorganic PCM present. Nanotechnology can be used to overcome these drawbacks. Nano-enhanced PCM are obtained by the dispersion of nanoparticles in the base material and thermal properties such as thermal conductivity, viscosity and specific heat capacity, within others, can be enhanced. This paper presents a review of the patents regarding the obtaining of nano-enhanced materials for thermal energy storage (TES) in order to realize the development nanotechnologies have gained in the TES field. Patents regarding the synthesis methods to obtain nano-enhanced phase materials (NEPCM) and TES systems using NEPCM have been found and are presented in the paper. The few existing number of patents found is a clear indicator of the recent and thus low development nanotechnology has in the TES field so far. Nevertheless, the results obtained with the reviewed inventions already show the big potential that nanotechnology has in TES and denote a more than probable expansion of its use in the next years. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Synergistic hepatoprotective potential of ethanolic extract of Solanum xanthocarpum and Juniperus communis against paracetamol and azithromycin induced liver injury in rats.

PubMed

Singh, Hem; Prakash, Atish; Kalia, A N; Majeed, Abu Bakar Abdul

2016-10-01

Previously explored combination therapies mostly involved the use of bioactive molecules. It is believed that herbal compounds containing multiple plant products have synergistic hepatoprotective effects and could enhance the desired actions. To investigate the combination of ethanolic fruits extract of Solanum xanthocarpum (SX) and Juniperus communis (JC) against Paracetamol (PCM) and Azithromycin (AZM) induced liver toxicity in rats. Liver toxicity was induced by combine oral administration of PCM (250 mg/kg) and AZM (200 mg/kg) for 7 days in Wistar rats. Fruit extract of SX (200 and 400 mg/kg) and JC (200 and 400 mg/kg) were administered daily for 14 days. The hepatoprotective activity was assessed using liver functional test, oxidative parameters and histopathological examination. The results demonstrated that combine administration of AZM and PCM significantly produced liver toxicity by increasing the serum level of hepatic enzymes and oxidative parameters in liver of rats. Histopathological examination also indicated that AZM and PCM produced liver damage in rats. Chronic treatment of SX and JC extract significantly and dose-dependently attenuated the liver toxicity by normalizing the biochemical factors and no gross histopathological changes were observed in liver of rats. Furthermore, combine administration of lower dose of SX and JC significantly potentiated their hepatoprotective effect which was significant as compared to their effect per se. The results clearly indicated that SX and JC extract has hepatoprotective potential against AZM and PCM induced liver toxicity due to their synergistic anti-oxidant properties.

A comparison between state-specific and linear-response formalisms for the calculation of vertical electronic transition energy in solution with the CCSD-PCM method.

PubMed

Caricato, Marco

2013-07-28

The calculation of vertical electronic transition energies of molecular systems in solution with accurate quantum mechanical methods requires the use of approximate and yet reliable models to describe the effect of the solvent on the electronic structure of the solute. The polarizable continuum model (PCM) of solvation represents a computationally efficient way to describe this effect, especially when combined with coupled cluster (CC) methods. Two formalisms are available to compute transition energies within the PCM framework: State-Specific (SS) and Linear-Response (LR). The former provides a more complete account of the solute-solvent polarization in the excited states, while the latter is computationally very efficient (i.e., comparable to gas phase) and transition properties are well defined. In this work, I review the theory for the two formalisms within CC theory with a focus on their computational requirements, and present the first implementation of the LR-PCM formalism with the coupled cluster singles and doubles method (CCSD). Transition energies computed with LR- and SS-CCSD-PCM are presented, as well as a comparison between solvation models in the LR approach. The numerical results show that the two formalisms provide different absolute values of transition energy, but similar relative solvatochromic shifts (from nonpolar to polar solvents). The LR formalism may then be used to explore the solvent effect on multiple states and evaluate transition probabilities, while the SS formalism may be used to refine the description of specific states and for the exploration of excited state potential energy surfaces of solvated systems.

Impact of Stoichiometry on the Structure of van der Waals Layered GeTe/Sb2 Te3 Superlattices Used in Interfacial Phase-Change Memory (iPCM) Devices.

PubMed

Kowalczyk, Philippe; Hippert, Françoise; Bernier, Nicolas; Mocuta, Cristian; Sabbione, Chiara; Batista-Pessoa, Walter; Noé, Pierre

2018-06-01

Van der Waals layered GeTe/Sb 2 Te 3 superlattices (SLs) have demonstrated outstanding performances for use in resistive memories in so-called interfacial phase-change memory (iPCM) devices. GeTe/Sb 2 Te 3 SLs are made by periodically stacking ultrathin GeTe and Sb 2 Te 3 crystalline layers. The mechanism of the resistance change in iPCM devices is still highly debated. Recent experimental studies on SLs grown by molecular beam epitaxy or pulsed laser deposition indicate that the local structure does not correspond to any of the previously proposed structural models. Here, a new insight is given into the complex structure of prototypical GeTe/Sb 2 Te 3 SLs deposited by magnetron sputtering, which is the used industrial technique for SL growth in iPCM devices. X-ray diffraction analysis shows that the structural quality of the SL depends critically on its stoichiometry. Moreover, high-angle annular dark-field-scanning transmission electron microscopy analysis of the local atomic order in a perfectly stoichiometric SL reveals the absence of GeTe layers, and that Ge atoms intermix with Sb atoms in, for instance, Ge 2 Sb 2 Te 5 blocks. This result shows that an alternative structural model is required to explain the origin of the electrical contrast and the nature of the resistive switching mechanism observed in iPCM devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reductions in Transmission Risk Behaviors in HIV-Positive Clients Receiving Prevention Case Management Services: Findings from a Community Demonstration Project

ERIC Educational Resources Information Center

Gasiorowicz, Mari; Llanas, Michelle R.; DiFranceisco, Wayne; Benotsch, Eric G.; Brondino, Michael J.; Catz, Sheryl L.; Hoxie, Neil J.; Reiser, William J.; Vergeront, James M.

2005-01-01

Prevention case management (PCM) for HIV-infected persons is an HIV risk reduction intervention designed to assist clients who are aware of their HIV infection and who continue to engage in risk transmission behaviors. PCM combines individual risk reduction counseling with case management to address the psychosocial factors affecting HIV…

Kaposi sarcoma and paracoccidioidomycosis in the same fragment of oral mucosa biopsy: a rare association in human immunodeficiency virus-positive patient. A case report.

PubMed

Pontes, Helder Antônio Rebelo; Guimarães, Douglas Magno; Pontes, Flávia Siroteau Corrêa; Paiva, Helena Borges; Pinto, Lara Carolina D'araujo; de Freitas Silva, Brunno Santos; Dos Santos Pinto, Décio

2011-02-01

The immunossuppression caused by HIV infection makes the affected individuals more susceptible to some diseases including infections, neoplasms, or even the association between them. Kaposi sarcoma (KS) is the most common AIDS-related neoplasm, featured as an angioproliferative disorder. Its cause seems to be related to the human herpesvirus type 8 and it is usually associated with lower CD4+ T cell count. Oral involvement is frequent, presenting red to blue-purplish plaques, maculaes, and nodules. On the other hand, paracoccidioidomycosis (PCM) is a systemic mycosis, endemic in Latin America, caused by Paracoccidioides brasiliensis. This mycosis is not commonly related to human immunodeficiency virus (HIV) infection, although PCM can be present in immunosuppression cases. Oral lesions, as granulomatous ulcers, are often identified in seropositive patients with PCM. A rare case, in which a male HIV-positive patient presented simultaneously Kaposi sarcoma and PCM in the same fragment of oral mucosa biopsy, is described. To the best of our knowledge, this concomitant association had not been previously described. Copyright © 2011 Elsevier Inc. All rights reserved.

Marketing of personalized cancer care on the web: an analysis of Internet websites.

PubMed

Gray, Stacy W; Cronin, Angel; Bair, Elizabeth; Lindeman, Neal; Viswanath, Vish; Janeway, Katherine A

2015-05-01

Internet marketing may accelerate the use of care based on genomic or tumor-derived data. However, online marketing may be detrimental if it endorses products of unproven benefit. We conducted an analysis of Internet websites to identify personalized cancer medicine (PCM) products and claims. A Delphi Panel categorized PCM as standard or nonstandard based on evidence of clinical utility. Fifty-five websites, sponsored by commercial entities, academic institutions, physicians, research institutes, and organizations, that marketed PCM included somatic (58%) and germline (20%) analysis, interpretive services (15%), and physicians/institutions offering personalized care (44%). Of 32 sites offering somatic analysis, 56% included specific test information (range 1-152 tests). All statistical tests were two-sided, and comparisons of website content were conducted using McNemar's test. More websites contained information about the benefits than limitations of PCM (85% vs 27%, P < .001). Websites specifying somatic analysis were statistically significantly more likely to market one or more nonstandard tests as compared with standard tests (88% vs 44%, P = .04). © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

An experimental study of PCM based finned and un-finned heat sinks for passive cooling of electronics

NASA Astrophysics Data System (ADS)

Usman, Hazrat; Ali, Hafiz Muhammad; Arshad, Adeel; Ashraf, Muhammad Junaid; Khushnood, Shahab; Janjua, Muhammad Mansoor; Kazi, S. N.

2018-05-01

This experimental study determines and compares the thermal performance of unfinned and finned PCM based heat sinks. For the analysis considering pin-fins as thermal conductivity enhancer (TCE), triangular configuration is considered. It is further classified into inline and staggered pin-fin arrangements. Three popular variants of paraffin namely paraffin wax, RT-44 and RT-35HC are incorporated as phase change materials (PCMs) inside the heat sink. The volume fraction of pin-fins and PCMs are kept constant at 9% and 90% respectively. The heat input at the base of heat sinks ranges from 5 W to 8 W. The results are presented in two different cases, charging and discharging, and the analysis of temperature variation and comparison of fin arrangements in three different heat sinks with and without PCM. Further the enhancement ratios are determined to quantify the thermal performance in operation time of heat sink for passive cooling with the influence of PCMs and TCEs. The results suggest triangular inline pin-fin as the dominant heat sink geometry and RT-44 as the most efficient PCM for passive thermal management of electronic devices.

Phase Change Material Heat Exchanger Life Test

NASA Technical Reports Server (NTRS)

Lillibridge, Sean; Stephan, Ryan

2009-01-01

Low Lunar Orbit (LLO) poses unique thermal challenges for the orbiting space craft, particularly regarding the performance of the radiators. The IR environment of the space craft varies drastically from the light side to the dark side of the moon. The result is a situation where a radiator sized for the maximal heat load in the most adverse situation is subject to freezing on the dark side of the orbit. One solution to this problem is to implement Phase Change Material (PCM) Heat Exchangers. PCM Heat Exchangers act as a "thermal capacitor," storing thermal energy when there is too much being produced by the space craft to reject to space, and then feeding that energy back into the thermal loop when conditions are more favorable. Because they do not use an expendable resource, such as the feed water used by sublimators and evaporators, PCM Heat Exchangers are ideal for long duration LLO missions. In order to validate the performance of PCM Heat Exchangers, a life test is being conducted on four n-Pentadecane, carbon filament heat exchangers. Fluid loop performance, repeatability, and measurement of performance degradation over 2500 melt-freeze cycles will be performed.

Use of phase change materials during compressed air expansion for isothermal CAES plants

NASA Astrophysics Data System (ADS)

Castellani, B.; Presciutti, A.; Morini, E.; Filipponi, M.; Nicolini, A.; Rossi, F.

2017-11-01

Compressed air energy storage (CAES) plants are designed to store compressed air into a vessel or in an underground cavern and to expand it in an expansion turbine when energy demand is high. An innovative CAES configuration recently proposed is the isothermal process. Several methods to implement isothermal CAES configuration are under investigation. In this framework, the present paper deals with the experimental testing of phase change materials (PCM) during compressed air expansion phase. The experimental investigation was carried out by means of an apparatus constituted by a compression section, a steel pressure vessel, to which an expansion valve is connected. The initial internal absolute pressure was equal to 5 bar to avoid moisture condensation and the experimental tests were carried out with two paraffin-based PCM amounts (0.05 kg and 0.1 kg). Results show that the temperature change during air expansion decreases with increasing the PCM amount inside the vessel. With the use of PCM during expansions an increase of the expansion work occurs. The increase is included in the range from 9.3% to 18.2%. In every test there is an approach to the isothermal values, which represent the maximum theoretical value of the obtainable expansion work.

Using Pre-melted Phase Change Material to Keep Payload Warm without Power for Hours in Space

NASA Technical Reports Server (NTRS)

Choi, Michael K.

2012-01-01

During a payload transition from the transport vehicle to its worksite on the International Space Station (ISS), the payload is unpowered for up to 6 hours. Its radiator(s) will continue to radiate heat to space. It is necessary to make up the heat loss to maintain the payload temperature above the cold survival limit. Typically an interplanetary Probe has no power generation system. It relies on its battery to provide limited power for the Communication and Data Handling (C&DH) subsystem during cruise, and heater power is unavailable. It is necessary to maintain the C&DH temperature above the minimum operating limit. This paper presents a novel thermal design concept that utilizes phase change material (PCM) to store thermal energy by melting it before the payload or interplanetary Probe is unpowered. For the ISS, the PCM is melted by heaters just prior to the payload transition from the transport vehicle to its worksite. For an interplanetary Probe, the PCM is melted by heaters just prior to separation from the orbiter. The PCM releases thermal energy to keep the payload warm for several hours after power is cut off.

Proton irradiation of CVD diamond detectors for high-luminosity experiments at the LHC

NASA Astrophysics Data System (ADS)

Meier, D.; Adam, W.; Bauer, C.; Berdermann, E.; Bergonzo, P.; Bogani, F.; Borchi, E.; Bruzzi, M.; Colledani, C.; Conway, J.; Dabrowski, W.; Delpierre, P.; Deneuville, A.; Dulinski, W.; van Eijk, B.; Fallou, A.; Foulon, F.; Friedl, M.; Jany, C.; Gan, K. K.; Gheeraert, E.; Grigoriev, E.; Hallewell, G.; Hall-Wilton, R.; Han, S.; Hartjes, F.; Hrubec, J.; Husson, D.; Kagan, H.; Kania, D.; Kaplon, J.; Kass, R.; Knöpfle, K. T.; Krammer, M.; Manfredi, P. F.; Marshall, R. D.; Mishina, M.; Le Normand, F.; Pan, L. S.; Palmieri, V. G.; Pernegger, H.; Pernicka, M.; Peitz, A.; Pirollo, S.; Pretzl, K.; Re, V.; Riester, J. L.; Roe, S.; Roff, D.; Rudge, A.; Schnetzer, S.; Sciortino, S.; Speziali, V.; Stelzer, H.; Stone, R.; Tapper, R. J.; Tesarek, R.; Thomson, G. B.; Trawick, M.; Trischuk, W.; Turchetta, R.; Walsh, A. M.; Wedenig, R.; Weilhammer, P.; Ziock, H.; Zoeller, M.; RD42 Collaboration

1999-04-01

CVD diamond shows promising properties for use as a position-sensitive detector for experiments in the highest radiation areas at the Large Hadron Collider. In order to study the radiation hardness of diamond we exposed CVD diamond detector samples to 24 Gev/ c and 500 Mev protons up to a fluence of 5×10 15 p/cm 2. We measured the charge collection distance, the average distance electron-hole pairs move apart in an external electric field, and leakage currents before, during, and after irradiation. The charge collection distance remains unchanged up to 1×10 15 p/cm 2 and decreases by ≈40% at 5×10 15 p/cm 2. Leakage currents of diamond samples were below 1 pA before and after irradiation. The particle-induced currents during irradiation correlate well with the proton flux. In contrast to diamond, a silicon diode, which was irradiated for comparison, shows the known large increase in leakage current. We conclude that CVD diamond detectors are radiation hard to 24 GeV/ c and 500 MeV protons up to at least 1×10 15p/cm 2 without signal loss.

Thermal analysis of a Phase Change Material for a Solar Organic Rankine Cycle

NASA Astrophysics Data System (ADS)

Iasiello, M.; Braimakis, K.; Andreozzi, A.; Karellas, S.

2017-11-01

Organic Rankine Cycle (ORC) is a promising technology for low temperature power generation, for example for the utilization of medium temperature solar energy. Since heat generated from solar source is variable throughout the day, the implementation of Thermal Energy Storage (TES) systems to guarantee the continuous operation of solar ORCs is a critical task, and Phase Change Materials (PCM) rely on latent heat to store large amounts of energy. In the present study, a thermal analysis of a PCM for a solar ORC is carried out. Three different types of PCMs are analyzed. The energy equation for the PCM is modeled by using the heat capacity method, and it is solved by employing a 1Dexplicit finite difference scheme. The solar source is modeled with a time-variable temperature boundary condition, with experimental data taken from the literature for two different solar collectors. Results are presented in terms of temperature profiles and stored energy. It has been shown that the stored energy depends on the heat source temperature, on the employed PCM and on the boundary conditions. It has been demonstrated that the use of a metal foam can drastically enhance the stored energy due to the higher overall thermal conductivity.

Development of a Hand Held Thromboelastograph

DTIC Science & Technology

2015-01-01

documents will be referenced during the Entegrion PCM System design, verification and validation activities. EN 61010 -1:2010 (Edition3.0) Safety...requirements for electrical equipment for measurement, control, and laboratory use – Part 1: General requirements. EN 61010 -2-101:2002 Safety...IPC-A-610E Acceptability of Electronic Assemblies IPC 7711/21B Rework, Modification and Repair of Electronic Assemblies. IEC 62304:2006/AC:2008

Permeation Testing of Materials With Chemical Agents or Simulants (Swatch Testing)

DTIC Science & Technology

2013-08-05

through a protective clothing material on a molecular level. Permeation involves the following: (1) sorption of molecules of the chemical into the...de Nemours and Company, Wilmington, Delaware), Teflon perfluoro- alkoxy ( PFA ), and Teflon polytetrafluoroethylene (PTFE). c. In all cases, only...pamphlet PCM positive control material PFA perfluoroalkoxy pH negative ion activity POL petroleum, oil, and lubricants PQL program quantification

Design of a thermosyphon-based thermal valve for controlled high-temperature heat extraction

DOE PAGES

Oshman, Christopher; Hardin, Corey; Rea, Jonathan; ...

2017-01-16

Conventional concentrated solar power (CSP) is a reliable alternative energy source that uses the sun’s heat to drive a heat engine to produce electrical power. An advantage of CSP is its ability to store thermal energy for use during off-sun hours which is typically done by storing sensible heat in molten salts. Alternatively, thermal energy may be stored as latent heat in a phase-change material (PCM), which stores large quantities of thermal energy in an isothermal process. On-sun, the PCM melts, storing energy. Off-sun, the latent heat is extracted to produce dispatchable electrical power. Here, this paper presents the designmore » of a thermosyphon-based device with sodium working fluid that is able to extract heat from a source as demand requires. A prototype has been designed to transfer 37 kW of thermal energy from a 600°C molten PCM tank to an array of 9% efficient thermoelectric generators (TEGs) to produce 3 kW of usable electrical energy for 5 h. This “thermal valve” design incorporates a funnel to collect condensate and a central shut-off valve to control condensate gravity return to the evaporator. Three circumferential tubes allow vapour transport up to the condenser. Pressure and a thermal resistance models were developed to predict the performance of the thermal valve. The pressure model predicts that the thermal valve will function as designed. The thermal resistance model predicts a 5500× difference in total thermal resistance between “on” and “off” states. The evaporator and condenser walls comprise 96% of the “on” thermal resistance, while the small parasitic heat transfer in the “off” state is primarily (77%) due to radiation losses. Lastly, this simple and effective technology can have a strong impact on the feasibility, scalability, and dispatchability of CSP latent storage. In addition, other industrial and commercial applications can benefit from this thermal valve concept.« less

Design of a thermosyphon-based thermal valve for controlled high-temperature heat extraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oshman, Christopher; Hardin, Corey; Rea, Jonathan

Conventional concentrated solar power (CSP) is a reliable alternative energy source that uses the sun’s heat to drive a heat engine to produce electrical power. An advantage of CSP is its ability to store thermal energy for use during off-sun hours which is typically done by storing sensible heat in molten salts. Alternatively, thermal energy may be stored as latent heat in a phase-change material (PCM), which stores large quantities of thermal energy in an isothermal process. On-sun, the PCM melts, storing energy. Off-sun, the latent heat is extracted to produce dispatchable electrical power. Here, this paper presents the designmore » of a thermosyphon-based device with sodium working fluid that is able to extract heat from a source as demand requires. A prototype has been designed to transfer 37 kW of thermal energy from a 600°C molten PCM tank to an array of 9% efficient thermoelectric generators (TEGs) to produce 3 kW of usable electrical energy for 5 h. This “thermal valve” design incorporates a funnel to collect condensate and a central shut-off valve to control condensate gravity return to the evaporator. Three circumferential tubes allow vapour transport up to the condenser. Pressure and a thermal resistance models were developed to predict the performance of the thermal valve. The pressure model predicts that the thermal valve will function as designed. The thermal resistance model predicts a 5500× difference in total thermal resistance between “on” and “off” states. The evaporator and condenser walls comprise 96% of the “on” thermal resistance, while the small parasitic heat transfer in the “off” state is primarily (77%) due to radiation losses. Lastly, this simple and effective technology can have a strong impact on the feasibility, scalability, and dispatchability of CSP latent storage. In addition, other industrial and commercial applications can benefit from this thermal valve concept.« less

Development flight instrumentation for the redesigned solid rocket booster for the Space Shuttle program

NASA Astrophysics Data System (ADS)

Stevens, Walter H.

This paper describes the upgraded development flight instrumentation (DFI) system for monitoring the performance of the redesigned solid rocket boosters. The DFI system, which was manufactured, qualification tested, and subsequently flown on STS-26 on September 29, 1988, consists of one main power distributor, two frequency division multiplexers, two wideband signal conditioners one PCM subsystem, one chamber pressure signal conditioner, one tape recorder, and one battery. The PCM subsystem, which was newly designed for this application, consists of one programmable master unit and three identical remote slave units. These units conditioned all of the information received from the sensors and multiplexed this data into one encoded PCM data stream and two independent FM composite outputs. Block diagrams of the DFI system and its subsystems are included.

Feasibility study of current pulse induced 2-bit/4-state multilevel programming in phase-change memory

NASA Astrophysics Data System (ADS)

Liu, Yan; Fan, Xi; Chen, Houpeng; Wang, Yueqing; Liu, Bo; Song, Zhitang; Feng, Songlin

2017-08-01

In this brief, multilevel data storage for phase-change memory (PCM) has attracted more attention in the memory market to implement high capacity memory system and reduce cost-per-bit. In this work, we present a universal programing method of SET stair-case current pulse in PCM cells, which can exploit the optimum programing scheme to achieve 2-bit/ 4state resistance-level with equal logarithm interval. SET stair-case waveform can be optimized by TCAD real time simulation to realize multilevel data storage efficiently in an arbitrary phase change material. Experimental results from 1 k-bit PCM test-chip have validated the proposed multilevel programing scheme. This multilevel programming scheme has improved the information storage density, robustness of resistance-level, energy efficient and avoiding process complexity.

Amelioration of Paracetamol-Induced Hepatotoxicity in Rat by the Administration of Methanol Extract of Muntingia calabura L. Leaves

PubMed Central

Mahmood, N. D.; Mamat, S. S.; Kamisan, F. H.; Yahya, F.; Kamarolzaman, M. F. F.; Nasir, N.; Mohtarrudin, N.; Tohid, S. F. Md.; Zakaria, Z. A.

2014-01-01

Muntingia calabura L. is a tropical plant species that belongs to the Elaeocarpaceae family. The present study is aimed at determining the hepatoprotective activity of methanol extract of M. calabura leaves (MEMC) using two models of liver injury in rats. Rats were divided into five groups (n = 6) and received 10% DMSO (negative control), 50 mg/kg N-acetylcysteine (NAC; positive control), or MEMC (50, 250, and 500 mg/kg) orally once daily for 7 days and on the 8th day were subjected to the hepatotoxic induction using paracetamol (PCM). The blood and liver tissues were collected and subjected to biochemical and microscopical analysis. The extract was also subjected to antioxidant study using the 2,2-diphenyl-1-picrylhydrazyl-(DPPH) and superoxide anion-radical scavenging assays. At the same time, oxygen radical antioxidant capacity (ORAC) and total phenolic content were also determined. From the histological observation, lymphocyte infiltration and marked necrosis were observed in PCM-treated groups (negative control), whereas maintenance of hepatic structure was observed in group pretreated with N-acetylcysteine and MEMC. Hepatotoxic rats pretreated with NAC or MEMC exhibited significant decrease (P < 0.05) in ALT and AST enzymes level. Moreover, the extract also exhibited good antioxidant activity. In conclusion, MEMC exerts potential hepatoprotective activity that could be partly attributed to its antioxidant activity and, thus warrants further investigations. PMID:24868543

Piezoelectric crystal microbalance measurements of enthalpy of sublimation of C2-C9 dicarboxylic acids

NASA Astrophysics Data System (ADS)

Dirri, F.; Palomba, E.; Longobardo, A.; Zampetti, E.

2016-02-01

We present here a novel experimental set-up that is able to measure the enthalpy of sublimation of a given compound by means of piezoelectric crystal microbalances (PCMs). The PCM sensors have already been used for space measurements, such as for the detection of organic and non-organic volatile species and refractory materials in planetary environments. In Earth atmospherics applications, PCMs can be also used to obtain some physical-chemical processes concerning the volatile organic compounds (VOCs) present in atmospheric environments. The experimental set-up has been developed and tested on dicarboxylic acids. In this work, a temperature-controlled effusion cell was used to sublimate VOC, creating a molecular flux that was collimated onto a cold PCM. The VOC recondensed onto the PCM quartz crystal, allowing the determination of the deposition rate. From the measurements of deposition rates, it has been possible to infer the enthalpy of sublimation of adipic acid, i.e. ΔHsub : 141.6 ± 0.8 kJ mol-1, succinic acid, i.e. 113.3 ± 1.3 kJ mol-1, oxalic acid, i.e. 62.5 ± 3.1 kJ mol-1, and azelaic acid, i.e. 124.2 ± 1.2 kJ mol-1. The results obtained show an accuracy of 1 % for succinic, adipic, and azelaic acid and within 5 % for oxalic acid and are in very good agreement with previous works (within 6 % for adipic, succinic, and oxalic acid and within 11 % or larger for azelaic acid).

A novel personal cooling system (PCS) incorporated with phase change materials (PCMs) and ventilation fans: An investigation on its cooling efficiency.

PubMed

Lu, Yehu; Wei, Fanru; Lai, Dandan; Shi, Wen; Wang, Faming; Gao, Chuansi; Song, Guowen

2015-08-01

Personal cooling systems (PCS) have been developed to mitigate the impact of severe heat stress for humans working in hot environments. It is still a great challenge to develop PCSs that are portable, inexpensive, and effective. We studied the performance of a new hybrid PCS incorporating both ventilation fans and phase change materials (PCMs). The cooling efficiency of the newly developed PCS was investigated on a sweating manikin in two hot conditions: hot humid (HH, 34°C, 75% RH) and hot dry (HD, 34°C, 28% RH). Four test scenarios were selected: fans off with no PCMs (i.e., Fan-off, the CONTROL), fans on with no PCMs (i.e., Fan-on), fans off with fully solidified PCMs (i.e., PCM+Fan-off), and fans on with fully solidified PCMs (i.e., PCM+Fan-on). It was found that the addition of PCMs provided a 54∼78min cooling in HH condition. In contrast, the PCMs only offered a 19-39min cooling in HD condition. In both conditions, the ventilation fans greatly enhanced the evaporative heat loss compared with Fan-off. The hybrid PCS (i.e., PCM+Fan-on) provided a continuous cooling effect during the three-hour test and the average cooling rate for the whole body was around 111 and 315W in HH and HD conditions, respectively. Overall, the new hybrid PCS may be an effective means of ameliorating symptoms of heat stress in both hot-humid and hot-dry environments. Copyright © 2015 Elsevier Ltd. All rights reserved.

An Isotonic Partial Credit Model for Ordering Subjects on the Basis of Their Sum Scores

ERIC Educational Resources Information Center

Ligtvoet, Rudy

2012-01-01

In practice, the sum of the item scores is often used as a basis for comparing subjects. For items that have more than two ordered score categories, only the partial credit model (PCM) and special cases of this model imply that the subjects are stochastically ordered on the common latent variable. However, the PCM is very restrictive with respect…

Neutrophil Extracellular Traps Identification in Tegumentary Lesions of Patients with Paracoccidioidomycosis and Different Patterns of NETs Generation In Vitro

PubMed Central

Della Coletta, Amanda Manoel; Bachiega, Tatiana Fernanda; de Quaglia e Silva, Juliana Carvalho; Soares, Ângela Maria Victoriano de Campos; De Faveri, Julio; Marques, Silvio Alencar; Marques, Mariângela Esther Alencar; Ximenes, Valdecir Farias; Dias-Melicio, Luciane Alarcão

2015-01-01

Paracoccidioidomycosis (PCM) is a systemic mycosis, endemic in most Latin American countries, especially in Brazil. It is caused by the thermo-dimorphic fungus of the genus Paracoccidioides (Paracoccidioides brasiliensis and Paracoccidioides lutzii). Innate immune response plays a crucial role in host defense against fungal infections, and neutrophils (PMNs) are able to combat microorganisms with three different mechanisms: phagocytosis, secretion of granular proteins, which have antimicrobial properties, and the most recent described mechanism called NETosis. This new process is characterized by the release of net-like structures called Neutrophil Extracellular Traps (NETs), which is composed of nuclear (decondensed DNA and histones) and granular material such as elastase. Several microorganisms have the ability of inducing NETs formation, including gram-positive and gram-negative bacteria, viruses and some fungi. We proposed to identify NETs in tegumentary lesions of patients with PCM and to analyze the interaction between two strains of P. brasiliensis and human PMNs by NETs formation in vitro. In this context, the presence of NETs in vivo was evidenced in tegumentary lesions of patients with PCM by confocal spectrum analyzer. Furthermore, we showed that the high virulent P. brasiliensis strain 18 (Pb18) and the lower virulent strain Pb265 are able to induce different patterns of NETs formation in vitro. The quantification of extracellular DNA corroborates the idea of the ability of P. brasiliensis in inducing NETs release. In conclusion, our data show for the first time the identification of NETs in lesions of patients with PCM and demonstrate distinct patterns of NETs in cultures challenged with fungi in vitro. The presence of NETs components both in vivo and in vitro open new possibilities for the detailed investigation of immunity in PCM. PMID:26327485

Acute juvenile Paracoccidioidomycosis: A 9-year cohort study in the endemic area of Rio de Janeiro, Brazil

PubMed Central

Almeida-Paes, Rodrigo; Freitas, Dayvison Francis Saraiva; Varon, Andréa Gina; Paixão, Ariane Gomes; Romão, Anselmo Rocha; Coutinho, Ziadir Francisco; Pizzini, Claudia Vera; Zancopé-Oliveira, Rosely Maria; Francesconi do Valle, Antonio Carlos

2017-01-01

Background Paracoccidioidomycosis (PCM) is a systemic mycosis caused by pathogenic dimorphic fungi of the genus Paracoccidioides. It is the most important systemic mycosis in Latin America and the leading cause of hospitalizations and death among them in Brazil. Acute PCM is less frequent but relevant because vulnerable young patients are affected and the severity is usually higher than that of the chronic type. Methods The authors performed a retrospective cohort study from 2001 to 2009 including acute juvenile PCM patients from a reference center in Rio de Janeiro, Brazil. Clinical, epidemiological, diagnostic, therapeutic, and prognostic data were reported. Results Twenty-nine patients were included. The average age was 23 years old and the male to female ratio was 1:1.07. All cases were referred from 3 of 9 existing health areas in the state of Rio de Janeiro, predominantly from urban areas (96.5%). Lymph nodes were the most affected organs (100%), followed by the skin and the spleen (31% each). Twenty-eight patients completed treatment (median 25 months) and progressed to clinical and serological cure; 1 death occurred. Twenty-four patients completed 48-month median follow-up. Four patients abandoned follow-up after the end of treatment. The most frequent sequela was low adrenal reserve. Paracoccidioides brasiliensis S1 was identified by partial sequencing of the arf and gp43 genes from 4 patients who presented a viable fungal culture. Conclusion Acute juvenile PCM is a severe disease with a high rate of complications. There are few cohort clinical studies of acute PCM in the literature. More studies should be developed to promote improvement in patients’ healthcare. PMID:28355221

Photodynamic inactivation of Paracoccidioides brasiliensis helps the outcome of oral paracoccidiodomycosis.

PubMed

Dos Santos, Letícia F M; Melo, Nathália B; de Carli, Marina L; Mendes, Ana Carolina S C; Bani, Giulia Maria A C; Verinaud, Liana M; Burger, Eva; de Oliveira I Moraes, Gabriel; Pereira, Alessandro A C; Brigagão, Maísa R L; Hanemann, João Adolfo C; Sperandio, Felipe F

2017-05-01

The antifungal drug therapy often employed to treat paracoccidiodomycosis (PCM), an important neglected fungal systemic infection, leads to offensive adverse effects, besides being very long-lasting. In addition, PCM compromises the oral health of patients by leading to oral lesions that are very painful and disabling. In that way, photodynamic therapy (PDT) arises as a new promising adjuvant treatment for inactivating Paracoccidioides brasiliensis (Pb), the responsible fungus for PCM, and also for helping the patients to deal with such debilitating oral lesions. PDT has been linked to an improved microbial killing, also presenting the advantage of not inducing immediate microbial resistance such as drugs. For the present study, we investigated the generation of reactive oxygen species (ROS) by using the fluorescent probes hydroxyphenyl fluorescein (HPF) and aminophenyl fluorescein (APF) after toluidine blue (TBO-37.5 mg/L)-mediated PDT (660 nm, 40 mW, and 0.04 cm 2 spot area) and the action of TBO-PDT upon Pb cultures grown for 7 or 15 days in semisolid Fava Netto's culture medium; we also targeted oral PCM manifestations by reporting the first clinical cases (three patients) to receive topic PDT for such purpose. We were able to show a significant generation of hydroxyl radicals and hypochlorite after TBO-PDT with doses around 90 J/cm 2 ; such ROS generation was particularly useful to attack and inactivate Pb colonies at 7 and 15 days. All three patients reported herein related an immediate relief when it came to pain, mouth opening, and also the ability to chew and swallow. As extracted from our clinical results, which are in fact based on in vitro outcomes, TBO-PDT is a very safe, inexpensive, and promising therapy for the oral manifestations of PCM.

Surface-promoted hydrolysis of 2,4,6-trinitrotoluene and 2,4-dinitroanisole on pyrogenic carbonaceous matter.

PubMed

Ding, Kai; Byrnes, Cory; Bridge, Jarrod; Grannas, Amanda; Xu, Wenqing

2018-04-01

This study investigates the fate of sorbed nitroaromatics on the surface of pyrogenic carbonaceous matter (PCM) to assess the feasibility of a PCM-promoted hydrolysis. The degradation of two nitroaromatic compounds, 2,4,6-trinitrotoluene (TNT) and 2,4-dinitroanisole, was observed at pH 7 in the presence of graphite powder, a model PCM. By contrast, no decay occurred without graphite. Using TNT as a model compound, our results suggest that TNT decay demonstrated a strong pH dependence, with no reaction at pH 3-5 but rapid degradation at pH 6-10. Moreover, by fitting TNT decay at different pH conditions along with its sorption kinetics to the Langmuir Kinetic Model, our results suggest that the base-catalyzed hydrolysis was important. The activation energy for TNT decay was obtained by measuring reaction rates at different temperatures with or without graphite and no significant difference was observed. However, the addition of tetramethylammonium cation was able to promote TNT decay possibly due to its ability to attract more OH - from the aqueous solution, leading to an increase in the sorbed OH - concentrations. Nitrite and a Meisenheimer complex were identified as degradation products for TNT. Other PCM, such as biochar, also demonstrated a comparable ability in promoting TNT decay at pH 7. Furthermore, a rapid degradation of TNT at pH 7 was observed when biochar was used as a soil amendment (4% by weight). Our results suggest that PCM can facilitate TNT and 2,4-dinitroanisole decay via a surface-promoted hydrolysis at neutral pH conditions, suggesting a promising alternative for in situ soil remediation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Variation of thermophysical parameters of PCM CaCl2.6H2O with dopant from T-history data analysis

NASA Astrophysics Data System (ADS)

Sutjahja, I. M.; Silalahi, Alfriska O.; Sukmawati, Nissa; Kurnia, D.; Wonorahardjo, S.

2018-03-01

T-history is a powerful method for deriving the thermophysical parameters of a phase change material (PCM), which consists of solid and liquid specific heats as well as latent heat enthalpy. The performance of a PCM for thermal energy storage could be altered by chemical dopants added directly to the PCM in order to form a stable suspension. We described in this paper the role of chemical dopants in the variation of thermophysical parameters for CaCl2 · 6H2O inorganic PCM with 1 wt% and 2 wt% dopant concentration and BaSO4 (1 wt%) as a nucleator using the T-history method. The dopant consists graphite and CuO nanoparticles. The data analysis follows the original method proposed by (Zhang et al 1999 Meas. Sci. Technol. 10 201–205) and its modification by (Hong et al 2004 Int. J. Refrig. 27 360–366). In addition, the enthalpy-temperature curve is obtained by adopting a method proposed by (Marín et al 2003 Meas. Sci. Technol. 14 184–189). We found that the solid specific heat tends to increase non-linearly with increased dopant concentration for all dopants. The increased liquid specific heat, however, indicates the optimum value for 1 wt% graphite dopant. In contrast, the CuO dopant shows a smaller increase in dopant concentration. The specific heat data are analyzed based on the interacting mesolayer model for a nanofluid. The heat of fusion show strong variation with dopant type, in agreement with other experimental data for various PCMs and dopant particles.

Active latent heat storage with a screw heat exchanger - experimental results for heat transfer and concept for high pressure steam

NASA Astrophysics Data System (ADS)

Zipf, Verena; Willert, Daniel; Neuhäuser, Anton

2016-05-01

An innovative active latent heat storage concept was invented and developed at Fraunhofer ISE. It uses a screw heat exchanger (SHE) for the phase change during the transport of a phase change material (PCM) from a cold to a hot tank or vice versa. This separates heat transfer and storage tank in comparison to existing concepts. A test rig has been built in order to investigate the heat transfer coefficients of the SHE during melting and crystallization of the PCM. The knowledge of these characteristics is crucial in order to assess the performance of the latent heat storage in a thermal system. The test rig contains a double shafted SHE, which is heated or cooled with thermal oil. The overall heat transfer coefficient U and the convective heat transfer coefficient on the PCM side hPCM both for charging and discharging have been calculated based on the measured data. For charging, the overall heat transfer coefficient in the tested SHE was Uch = 308 W/m2K and for discharging Udis = 210 W/m2K. Based on the values for hPCM the overall heat transfer coefficients for a larger SHE with steam as heat transfer fluid and an optimized geometry were calculated with Uch = 320 W/m2K for charging and Udis = 243 W/m2K for discharging. For pressures as high as p = 100 bar, an SHE concept has been developed, which uses an organic fluid inside the flight of the SHE as working media. With this concept, the SHE can also be deployed for very high pressure, e.g. as storage in solar thermal power plants.

Evaluating variation in use of definitive therapy and risk-adjusted prostate cancer mortality in England and the USA.

PubMed

Sachdeva, Ashwin; van der Meulen, Jan H; Emberton, Mark; Cathcart, Paul J

2015-02-24

Prostate cancer mortality (PCM) in the USA is among the lowest in the world, whereas PCM in England is among the highest in Europe. This paper aims to assess the association of variation in use of definitive therapy on risk-adjusted PCM in England as compared with the USA. Observational study. Cancer registry data from England and the USA. Men diagnosed with non-metastatic prostate cancer (PCa) in England and the USA between 2004 and 2008. Competing-risks survival analyses to estimate subhazard ratios (SHR) of PCM adjusted for age, ethnicity, year of diagnosis, Gleason score (GS) and clinical tumour (cT) stage. 222,163 men were eligible for inclusion. Compared with American patients, English patients were more likely to present at an older age (70-79 years: England 44.2%, USA 29.3%, p<0.001), with higher tumour stage (cT3-T4: England 25.1%, USA 8.6%, p<0.001) and higher GS (GS 8-10: England 20.7%, USA 11.2%, p<0.001). They were also less likely to receive definitive therapy (England 38%, USA 77%, p<0.001). English patients were more likely to die of PCa (SHR=1.9, 95% CI 1.7 to 2.0, p<0.001). However, this difference was no longer statistically significant when also adjusted for use of definitive therapy (SHR=1.0, 95% CI 1.0 to 1.1, p=0.3). Risk-adjusted PCM is significantly higher in England compared with the USA. This difference may be explained by less frequent use of definitive therapy in England. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

What are the potential benefits of including latent storage in common wallboard?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, T.K.; Tomlinson, J.J.

1995-11-01

Previous work has shown that wallboard can be successfully manufactured to contain up to 30% phase-change material (PCM), or wax, thus enabling this common building material to serve as a thermal energy storage device. The PCM wallboard was analyzed for passive solar applications and found to save energy with a reasonable payback time period of five years. Further evaluations of the wallboard are reported in this paper. This analysis looks at potential applications of PCM wallboard as a load management device and as a comfort enhancer. Results show that the wallboard is ineffective in modifying the comfort level but canmore » provide significant load management relief. In some applications the load management strategy also serves to save a small amount of energy, in others there is a small energy penalty.« less

Get Connected: an HIV prevention case management program for men and women leaving California prisons.

PubMed

Myers, Janet; Zack, Barry; Kramer, Katie; Gardner, Mick; Rucobo, Gonzalo; Costa-Taylor, Stacy

2005-10-01

Individuals leaving prison face challenges to establishing healthy lives in the community, including opportunities to engage in behavior that puts them at risk for HIV transmission. HIV prevention case management (PCM) can facilitate linkages to services, which in turn can help remove barriers to healthy behavior. As part of a federally funded demonstration project, the community-based organization Centerforce provided 5 months of PCM to individuals leaving 3 state prisons in California. Program effects were measured by assessing changes in risk behavior, access to services, reincarnation, and program completion. Although response rates preclude definitive conclusions, HIV risk behavior did decrease. Regardless of race, age, or gender, those receiving comprehensive health services were significantly more likely to complete the program. PCM appears to facilitate healthy behavior for individuals leaving prison.

A Summary of the Naval Postgraduate School Research Program.

DTIC Science & Technology

1982-05-01

and testing of PCM modu- lation formats, design and test of an underwater video line using a diver’s handheld camera and bi-directional interconnection...to design and develop advanced control schemes which successfully optimize the tor- pedo steering performance for Project Courageous. cummary: Work...investigating the feasibility and design of fiber optic communications in underwater torpedo ranges. Summary: An underwater fiber optic video uplink was

Worldwide Report, Telecommunications Policy, Research, and Development

DTIC Science & Technology

1985-12-06

11 Nov 85) 81 FEDERAL REPUBLIC OF GERMANY Commission To Investigate How To Improve Domestic Technology (R. Schulze; Duesseldorf VDI NACHRICHTEN...from four terminal interfaces to generate the international standard PCM-32 link (which has a data rate of 2048 kbps). Four PCM 32 links (from 128...INVESTIGATE HOW TO IMPROVE DOMESTIC TECHNOLOGY Duesseldorf VDI NACHRICHTEN in German 3 May 85 p 2 [Article by R. Schulze: "Communications

77 FR 7521 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-13

... product operators Replace rudder PCM (P/N 241700- 11 work-hours x $85 $5,856 $6,791 $47,537 1007). per... = $935. Modify rudder PCM (P/N 241700-1007) 3 work-hours x $85 1,374 1,629 11,403 per hours = $255... part number (P/N) 60B80093-3 (Parker P/N 241700-1005) or Boeing P/N 60B80093-4 (Parker P/N 241700-1007...

Serum antibody levels correlate with oral fungal cell numbers and influence the patients' response to chronic paracoccidioidomycosis.

PubMed

de Carli, Marina Lara; Cardoso, Beatriz Cristina Bachião; Malaquias, Luiz Cosme Cotta; Nonogaki, Suely; Pereira, Alessandro Antônio Costa; Sperandio, Felipe Fornias; Hanemann, João Adolfo Costa

2015-06-01

Paracoccidioidomycosis (PCM) is a neglected fungal disease that elicits an important granulomatous inflammatory reaction which aims to isolate the fungi and resolve the infection; besides the innate cellular response, the patients' sera may contain different levels of antibodies directed against PCM's pathogenic agent: Paracoccidioides brasiliensis (Pb). The aim of the study was to assess the distinct serum antibody levels of 19 chronic PCM patients and to associate these levels to the granulomatous inflammatory response and presence of fungi in oral lesions caused by Pb. The presence of Pb was detected and counted within oral tissues using immunohistochemistry; antibody levels were classified as negative, low-grade, moderate or high-grade groups. The Kruskal-Wallis and Dunn's test were used to verify possible associations among the groups. Interestingly, lower antibody titres were associated with lesser numbers of Pb, which favours the cellular response over the humoral response to fight PCM. On the other hand, negative serological results were linked to a higher presence of Pb in the tissues, indicating that a deficient humoral response supports the fungal proliferation. The number of Pb was conveniently associated with the level of serum antibodies, showing that the humoral immune response is required, however, not solely responsible to restrain the dissemination of Pb. © 2015 Blackwell Verlag GmbH.

Performance enhancement of fin attached ice-on-coil type thermal storage tank for different fin orientations using constrained and unconstrained simulations

NASA Astrophysics Data System (ADS)

Kim, M. H.; Duong, X. Q.; Chung, J. D.

2017-03-01

One of the drawbacks in latent thermal energy storage system is the slow charging and discharging time due to the low thermal conductivity of the phase change materials (PCM). This study numerically investigated the PCM melting process inside a finned tube to determine enhanced heat transfer performance. The influences of fin length and fin numbers were investigated. Also, two different fin orientations, a vertical and horizontal type, were examined, using two different simulation methods, constrained and unconstrained. The unconstrained simulation, which considers the density difference between the solid and liquid PCM showed approximately 40 % faster melting rate than that of constrained simulation. For a precise estimation of discharging performance, unconstrained simulation is essential. Thermal instability was found in the liquid layer below the solid PCM, which is contrary to the linear stability theory, due to the strong convection driven by heat flux from the coil wall. As the fin length increases, the area affected by the fin becomes larger, thus the discharging time becomes shorter. The discharging performance also increased as the fin number increased, but the enhancement of discharging performance by more than two fins was not discernible. The horizontal type shortened the complete melting time by approximately 10 % compared to the vertical type.

Phase change energy storage for solar dynamic power systems

NASA Technical Reports Server (NTRS)

Chiaramonte, F. P.; Taylor, J. D.

1992-01-01

This paper presents the results of a transient computer simulation that was developed to study phase change energy storage techniques for Space Station Freedom (SSF) solar dynamic (SD) power systems. Such SD systems may be used in future growth SSF configurations. Two solar dynamic options are considered in this paper: Brayton and Rankine. Model elements consist of a single node receiver and concentrator, and takes into account overall heat engine efficiency and power distribution characteristics. The simulation not only computes the energy stored in the receiver phase change material (PCM), but also the amount of the PCM required for various combinations of load demands and power system mission constraints. For a solar dynamic power system in low earth orbit, the amount of stored PCM energy is calculated by balancing the solar energy input and the energy consumed by the loads corrected by an overall system efficiency. The model assumes an average 75 kW SD power system load profile which is connected to user loads via dedicated power distribution channels. The model then calculates the stored energy in the receiver and subsequently estimates the quantity of PCM necessary to meet peaking and contingency requirements. The model can also be used to conduct trade studies on the performance of SD power systems using different storage materials.

Phase change energy storage for solar dynamic power systems

NASA Astrophysics Data System (ADS)

Chiaramonte, F. P.; Taylor, J. D.

This paper presents the results of a transient computer simulation that was developed to study phase change energy storage techniques for Space Station Freedom (SSF) solar dynamic (SD) power systems. Such SD systems may be used in future growth SSF configurations. Two solar dynamic options are considered in this paper: Brayton and Rankine. Model elements consist of a single node receiver and concentrator, and takes into account overall heat engine efficiency and power distribution characteristics. The simulation not only computes the energy stored in the receiver phase change material (PCM), but also the amount of the PCM required for various combinations of load demands and power system mission constraints. For a solar dynamic power system in low earth orbit, the amount of stored PCM energy is calculated by balancing the solar energy input and the energy consumed by the loads corrected by an overall system efficiency. The model assumes an average 75 kW SD power system load profile which is connected to user loads via dedicated power distribution channels. The model then calculates the stored energy in the receiver and subsequently estimates the quantity of PCM necessary to meet peaking and contingency requirements. The model can also be used to conduct trade studies on the performance of SD power systems using different storage materials.

High-power direct ethylene glycol fuel cell (DEGFC) based on nanoporous proton-conducting membrane (NP-PCM)

NASA Astrophysics Data System (ADS)

Peled, E.; Livshits, V.; Duvdevani, T.

We recently reported the development of a new nanoporous proton-conducting membrane (NP-PCM) and have applied it in a direct methanol fuel cell (DMFC) and in other direct oxidation fuel cells. The use of the NP-PCM in the DMFC offers several advantages over the Nafion-based DMFC including lower membrane cost, lower methanol crossover which leads to a much higher fuel utilization and higher conductivity. In this work, we found that the 90 °C swelling of the NP-PCM is only 5-8% and that the diffusion constant of methanol at 80-130 °C is higher by a factor of 1.5-3 than that of ethylene glycol (EG). The maximum power density of methanol/oxygen and EG/oxygen FCs equipped with a 100 μm thick NP-PCMs is 400 and 300 mW/cm 2 respectively, higher than that for a DMFC based on Nafion 115 (260 mW/cm 2 [Eletrochem. Solid-State Lett. 4 (4) (2001) A31]. This puts the DEGFC in direct competition with both DMFC and indirect methanol FC. Ethylene glycol (EG) is well known in the automobile industry and in contrast to methanol, its distribution infrastructure already exists, thus it is a promising candidate for practical electric vehicles.

Multiparity modifies contractile properties of pelvic muscles affecting the genesis of vaginal pressure in rabbits.

PubMed

López-Juárez, Rhode; Zempoalteca, René; Corona-Quintanilla, Dora Luz; Jiménez-Estrada, Ismael; Castelán, Francisco; Martínez-Gómez, Margarita

2018-01-01

To characterize the contractile properties of the bulbospongiosus (Bsm), isquiocavernosus (Ism), and pubococcygeus muscles (Pcm), and their involvement in the genesis of vaginal pressure in nulliparous and multiparous rabbits. Age-matched nulliparous and multiparous rabbits were used to record the isometric contractile responses of each muscle as well as the intravaginal pressure evoked by single square electrical pulses and stimulation trains of ascending frequency. To establish significant differences between groups, two-tail unpaired Student t tests were carried out. The linear correlation between intravaginal pressure and muscle contractile force was analyzed with Pearson correlation tests. For all cases, a P ≤ 0.05 was set as statistically significant. Multiparity decreased the contractile force of Bsm and Ism generated by high-frequency stimulation trains. The normalized force of the Pcm increased when evoked at 1, 4, and 10 Hz while this decreased at higher frequencies (20, 50, and 100 Hz). The contraction of both Bsm and Ism raised particularly the pressure on the perineal vagina while that of the Pcm increased the pressure in the pelvic vagina. Such a functional segregation is still present in multiparous rabbits albeit it was modified. Multiparity induces changes in the contractile responses of Bsm, Ism, and Pcm, which alterates the vaginal pressure. © 2017 Wiley Periodicals, Inc.

Fabrication of 3D lawn-shaped N-doped porous carbon matrix/polyaniline nanocomposite as the electrode material for supercapacitors

NASA Astrophysics Data System (ADS)

Zhang, Xiuling; Ma, Li; Gan, Mengyu; Fu, Gang; Jin, Meng; Lei, Yao; Yang, Peishu; Yan, Maofa

2017-02-01

A facile approach to acquire electrode materials with prominent electrochemical property is pivotal to the progress of supercapacitors. 3D nitrogen-doped porous carbon matrix (PCM), with high specific surface area (SSA) up to 2720 m2 g-1, was obtained from the carbonization and activation of the nitrogen-enriched composite precursor (graphene/polyaniline). Then 3D lawn-shaped PCM/PANI composite was obtained by the simple in-situ polymerization. The morphology and structure of these resulting composites were characterized by combining SEM and TEM measurements, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) spectroscopy analyses and Raman spectroscope. The element content of all samples was evaluated using CHN analysis. The results of electrochemical testing indicated that the PCM/PANI composite displays a higher capacitance value of 527 F g-1 at 1 A g-1 compared to 338 F g-1 for pure PANI, and exhibits appreciable rate capability with a retention of 76% at 20 A g-1 as well as fine long-term cycling performance (with 88% retention of specific capacitance after 1000 cycles at 10 A g-1). Simultaneously, the excellent capacitance performance coupled with the facile synthesis of PCM/PANI indicates it is a promising electrode material for supercapacitors.

Metallic phase change material thermal storage for Dish Stirling

DOE PAGES

Andraka, C. E.; Kruizenga, A. M.; Hernandez-Sanchez, B. A.; ...

2015-06-05

Dish-Stirling systems provide high-efficiency solar-only electrical generation and currently hold the world record at 31.25%. This high efficiency results in a system with a high possibility of meeting the DOE SunShot goal of $0.06/kWh. However, current dish-Stirling systems do not incorporate thermal storage. For the next generation of non-intermittent and cost-competitive solar power plants, we propose adding a thermal energy storage system that combines latent (phase-change) energy transport and latent energy storage in order to match the isothermal input requirements of Stirling engines while also maximizing the exergetic efficiency of the entire system. This paper reports current findings in themore » area of selection, synthesis and evaluation of a suitable high performance metallic phase change material (PCM) as well as potential interactions with containment alloy materials. The metallic PCM's, while more expensive than salts, have been identified as having substantial performance advantages primarily due to high thermal conductivity, leading to high exergetic efficiency. Systems modeling has indicated, based on high dish Stirling system performance, an allowable cost of the PCM storage system that is substantially higher than SunShot goals for storage cost on tower systems. Several PCM's are identified with suitable melting temperature, cost, and performance.« less

Experimental Investigation of A Heat Pipe-Assisted Latent Heat Thermal Energy Storage System

NASA Astrophysics Data System (ADS)

Tiari, Saeed; Mahdavi, Mahboobe; Qiu, Songgang

2016-11-01

In the present work, different operation modes of a latent heat thermal energy storage system assisted by a heat pipe network were studied experimentally. Rubitherm RT55 enclosed by a vertical cylindrical container was used as the Phase Change Material (PCM). The embedded heat pipe network consisting of a primary heat pipe and an array of four secondary heat pipes were employed to transfer heat to the PCM. The primary heat pipe transports heat from the heat source to the heat sink. The secondary heat pipes transfer the extra heat from the heat source to PCM during charging process or retrieve thermal energy from PCM during discharging process. The effects of heat transfer fluid (HTF) flow rate and temperature on the thermal performance of the system were investigated for both charging and discharging processes. It was found that the HTF flow rate has a significant effect on the total charging time of the system. Increasing the HTF flow rate results in a remarkable increase in the system input thermal power. The results also showed that the discharging process is hardly affected by the HTF flow rate but HTF temperature plays an important role in both charging and discharging processes. The authors would like to acknowledge the financial supports by Temple University for the project.

Smart Polyacrylonitrile (PAN) Nanofibers with Thermal Energy Storage and Retrieval Functionality

NASA Astrophysics Data System (ADS)

Cherry, De'Andre James

Phase change materials (PCMs) are generally substances with a high heat of fusion in the process of solid to liquid phase change. The nature of PCMs make them efficient materials to store and retrieve large amounts of thermal energy. Presently, high efficiency thermal energy storage/retrieval in applications where flexibility and space saving are required, such as smart textiles, still remains as a challenge. In this study, lauric acid (LA) and myristic acid (MA) were combined to prepare a specific binary fatty acid eutectic (LA-MA) with a melting point near the operating body temperature of a human being and then encapsulated in polyacrylonitrile (PAN) nanofibers through the electrospinning technique. Functionalized PCM-enhanced PAN nanofibers containing LA-MA at 30%, 50%, 70% and 100% of the weight of the PAN were successfully synthesized. The morphological structures and thermal energy storage capacity of the PCM-enhanced PAN nanofibers were characterized by electron microscopy (EM) and differential scanning calorimetry (DSC). The novel PCM-enhanced PAN nanofibers maintained their cylindrical fiber morphology after multiple heating-cooling cycles and retained their latent heat storage functionality. Thus, it is envisioned that the prepared PCM-enhanced PAN nanofibers will find use in applications such as smart textiles where temperature regulation functionality is required.

Solar-thermal conversion and thermal energy storage of graphene foam-based composites.

PubMed

Zhang, Lianbin; Li, Renyuan; Tang, Bo; Wang, Peng

2016-08-14

Among various utilizations of solar energy, solar-thermal conversion has recently gained renewed research interest due to its extremely high energy efficiency. However, one limiting factor common to all solar-based energy conversion technologies is the intermittent nature of solar irradiation, which makes them unable to stand-alone to satisfy the continuous energy need. Herein, we report a three-dimensional (3D) graphene foam and phase change material (PCM) composite for the seamlessly combined solar-thermal conversion and thermal storage for sustained energy release. The composite is obtained by infiltrating the 3D graphene foam with a commonly used PCM, paraffin wax. The high macroporosity and low density of the graphene foam allow for high weight fraction of the PCM to be incorporated, which enhances the heat storage capacity of the composite. The interconnected graphene sheets in the composite provide (1) the solar-thermal conversion capability, (2) high thermal conductivity and (3) form stability of the composite. Under light irradiation, the composite effectively collects and converts the light energy into thermal energy, and the converted thermal energy is stored in the PCM and released in an elongated period of time for sustained utilization. This study provides a promising route for sustainable utilization of solar energy.

Performance analysis of phase-change material storage unit for both heating and cooling of buildings

NASA Astrophysics Data System (ADS)

Waqas, Adeel; Ali, Majid; Ud Din, Zia

2017-04-01

Utilisation of solar energy and the night ambient (cool) temperatures are the passive ways of heating and cooling of buildings. Intermittent and time-dependent nature of these sources makes thermal energy storage vital for efficient and continuous operation of these heating and cooling techniques. Latent heat thermal energy storage by phase-change materials (PCMs) is preferred over other storage techniques due to its high-energy storage density and isothermal storage process. The current study was aimed to evaluate the performance of the air-based PCM storage unit utilising solar energy and cool ambient night temperatures for comfort heating and cooling of a building in dry-cold and dry-hot climates. The performance of the studied PCM storage unit was maximised when the melting point of the PCM was ∼29°C in summer and 21°C during winter season. The appropriate melting point was ∼27.5°C for all-the-year-round performance. At lower melting points than 27.5°C, declination in the cooling capacity of the storage unit was more profound as compared to the improvement in the heating capacity. Also, it was concluded that the melting point of the PCM that provided maximum cooling during summer season could be used for winter heating also but not vice versa.

High-Temperature Phase Change Materials (PCM) Candidates for Thermal Energy Storage (TES) Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez, J. C.

2011-09-01

It is clearly understood that lower overall costs are a key factor to make renewable energy technologies competitive with traditional energy sources. Energy storage technology is one path to increase the value and reduce the cost of all renewable energy supplies. Concentrating solar power (CSP) technologies have the ability to dispatch electrical output to match peak demand periods by employing thermal energy storage (TES). Energy storage technologies require efficient materials with high energy density. Latent heat TES systems using phase change material (PCM) are useful because of their ability to charge and discharge a large amount of heat from amore » small mass at constant temperature during a phase transformation like melting-solidification. PCM technology relies on the energy absorption/liberation of the latent heat during a physical transformation. The main objective of this report is to provide an assessment of molten salts and metallic alloys proposed as candidate PCMs for TES applications, particularly in solar parabolic trough electrical power plants at a temperature range from 300..deg..C to 500..deg.. C. The physical properties most relevant for PCMs service were reviewed from the candidate selection list. Some of the PCM candidates were characterized for: chemical stability with some container materials; phase change transformation temperatures; and latent heats.« less

Water Based Phase Change Material Heat Exchanger Development

NASA Technical Reports Server (NTRS)

Hansen, Scott W.; Sheth, Ribik B.; Atwell, Matt; Cheek, Ann; Agarwal, Muskan; Hong, Steven; Patel, Aashini,; Nguyen, Lisa; Posada, Luciano

2014-01-01

In a cyclical heat load environment such as low Lunar orbit, a spacecraft’s radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a “topper” to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. Studies conducted in this paper investigate utilizing water’s high latent heat of formation as a PCM, as opposed to traditional waxes, and corresponding complications surrounding freezing water in an enclosed volume. Work highlighted in this study is primarily visual and includes understanding ice formation, freeze front propagation, and the solidification process of water/ice. Various test coupons were constructed of copper to emulate the interstitial pin configuration (to aid in conduction) of the proposed water PCM HX design. Construction of a prototypic HX was also completed in which a flexible bladder material and interstitial pin configurations were tested. Additionally, a microgravity flight was conducted where three copper test articles were frozen continuously during microgravity and 2-g periods and individual water droplets were frozen during microgravity.

The process of processing: exploring the validity of Neisser's perceptual cycle model with accounts from critical decision-making in the cockpit.

PubMed

Plant, Katherine L; Stanton, Neville A

2015-01-01

The perceptual cycle model (PCM) has been widely applied in ergonomics research in domains including road, rail and aviation. The PCM assumes that information processing occurs in a cyclical manner drawing on top-down and bottom-up influences to produce perceptual exploration and actions. However, the validity of the model has not been addressed. This paper explores the construct validity of the PCM in the context of aeronautical decision-making. The critical decision method was used to interview 20 helicopter pilots about critical decision-making. The data were qualitatively analysed using an established coding scheme, and composite PCMs for incident phases were constructed. It was found that the PCM provided a mutually exclusive and exhaustive classification of the information-processing cycles for dealing with critical incidents. However, a counter-cycle was also discovered which has been attributed to skill-based behaviour, characteristic of experts. The practical applications and future research questions are discussed. Practitioner Summary: This paper explores whether information processing, when dealing with critical incidents, occurs in the manner anticipated by the perceptual cycle model. In addition to the traditional processing cycle, a reciprocal counter-cycle was found. This research can be utilised by those who use the model as an accident analysis framework.

A Diagnostic Approach for Rodent Progressive Cardiomyopathy and Like Lesions in Toxicology Studies up to 28 Days in the Sprague Dawley Rat (Part 2 of 2).

PubMed

Hailey, James R; Maleeff, Beverly E; Thomas, Heath C; Pearse, Gail; Klapwijk, Jan C; Cristofori, Patrizia G; Berridge, Brian; Kimbrough, Carie L; Parker, George A; Morton, Daniel; Elmore, Susan; Hardisty, Jerry F; Dybdal, Noel O; Rehagen, David A; Fikes, James D; Lamb, Martin; Biddle, Kathleen; Buetow, Bernard S; Carreira, Vinicius; Nyska, Abraham; Tripathi, Niraj K; Workman, Heather C; Bienvenu, Jean-Guy; Brees, Ingrid; Turk, James R; Adler, Rick R

2017-12-01

To test the diagnostic approach described in part 1 of this article, 2 exercises were completed by pathologists from multiple companies/agencies. Pathologist's examination of whole slide image (WSI) heart sections from rats using personal diagnostic approaches (exercise #1) corroborated conclusions from study #1. Using the diagnostic approach described in part 1, these pathologists examined the same WSI heart sections (exercise #2) to determine whether that approach increased consistency of diagnosis of rodent progressive cardiomyopathy (PCM) lesions. In exercise #2, there was improved consistency of categorization of small borderline morphologies and mild lesions, but a decrement in consistency of categorizing minimal lesions. Exercises 1 and 2 suggest the described diagnostic approach is representative of that in use by the majority of toxicologic pathologists across companies/agencies and that application by all may improve diagnostic consistency of PCM/like lesions. Additionally, a criterion of approximately 5% heart section involvement is suggested for separating mild from moderate or greater severity. While evidence is not absolute, until further investigation shows otherwise, microscopic changes resembling PCM, but located in the epicardial and subepicardial region of the right ventricle, may be considered as part of the spectrum of PCM.

Airborne UV photon-counting radiometer

NASA Astrophysics Data System (ADS)

Bauer, Marc C.; Wilcher, George; Banks, Calvin R.; Wood, Ronald L.

2000-11-01

The radiometric measurements group at the Arnold Engineering Development Center (AEDC) has developed new solar-blind radiometers for the SENSOR TALON flight test. These radiometers will be flown in an instrument pod by the 46th Test Wing at Eglin AFB. The radiometers are required to fit into a single quadrant of a 22-in.-diam sphere turret of the instrument pod. Because of minimal space requirements and photon-counting sensitivity needs, the radiometric measurements group used image intensifiers instead of the standard photomultiplier tubes (PMTs). The new design concept improved the photon-counting sensitivity, dynamic range, and uniformity of the field of view as compared to standard PMTs. A custom data acquisition system was required to miniaturize the electronics and generate a pulse code-modulated (PCM) data stream to the standard tape recording system.

DFT/PCM, QTAIM, 1H NMR conformational studies and QSAR modeling of thirty-two anti-Leishmania amazonensis Morita-Baylis-Hillman Adducts

NASA Astrophysics Data System (ADS)

Filho, Edilson B. A.; Moraes, Ingrid A.; Weber, Karen C.; Rocha, Gerd B.; Vasconcellos, Mário L. A. A.

2012-08-01

Morita-Baylis-Hillman Adducts (MBHA) has been recently synthesized and bio-evaluated by our research group against Leishmania amazonensis, parasite that causes cutaneous and mucocutaneous leishmaniasis. We present here a theoretical conformational study of thirty-two leismanicidal MBHA by B3LYP/6-31+g(d) calculations with Polarized Continuum Model (PCM) to simulate water influence. Intramolecular Hydrogen Bonds (IHBs) indicated to control the most conformational preferences of MBHA. Quantum Theory Atoms in Molecules (QTAIM) calculations were able to characterize these interactions at Bond Critical Point level. Compounds presenting an unusual seven member IHB between NO2 group and hydroxyl moiety, supported by experimental spectroscopic data, showed a considerable improvement of biological activity (lower IC50 values). These results are in accordance to redox NO2 mechanism of action. Based on structural observations, some molecular descriptors were calculated and submitted to Quantitative Structure-Activity Relationship (QSAR) studies through the PLS Regression Method. These studies provided a model with good validation parameters values (R2 = 0.71, Q2 = 0.61 and Qext2 = 0.92).

Mirror-symmetric Magneto-optical Kerr Rotation using Visible Light in [(GeTe)2(Sb2Te3)1]n Topological Superlattices

PubMed Central

Bang, Do; Awano, Hiroyuki; Tominaga, Junji; Kolobov, Alexander V.; Fons, Paul; Saito, Yuta; Makino, Kotaro; Nakano, Takashi; Hase, Muneaki; Takagaki, Yukihiko; Giussani, Alessandro; Calarco, Raffaella; Murakami, Shuichi

2014-01-01

Interfacial phase change memory (iPCM), that has a structure of a superlattice made of alternating atomically thin GeTe and Sb2Te3 layers, has recently attracted attention not only due to its superior performance compared to the alloy of the same average composition in terms of energy consumption but also due to its strong response to an external magnetic field (giant magnetoresistance) that has been speculated to arise from switching between topological insulator (RESET) and normal insulator (SET) phases. Here we report magneto-optical Kerr rotation loops in the visible range, that have mirror symmetric resonances with respect to the magnetic field polarity at temperatures above 380 K when the material is in the SET phase that has Kramers-pairs in spin-split bands. We further found that this threshold temperature may be controlled if the sample was cooled in a magnetic field. The observed results open new possibilities for use of iPCM beyond phase-change memory applications. PMID:25030304

Chronic paracoccidioidmycosis in a woman with Crohn Disease.

PubMed

Tavares Dos Santos, Harim; Augusto Benevenuto de Andrade, Bruno; Fernandes, Darcy; Caxias Travassos, Daphine; Bufalino, Andreia

2017-04-15

We report a rare case of chronic paracoccidioidomycosis(PCM) in a woman with Crohn disease in the setting of treatment with azathioprine and mesalazine. Serum tests for antigens to Paracoccidioides brasiliensis, Histoplasma capsulatum, and Aspergillus fumigatus were negative. An incisional biopsy of an oral lesion with periodic acid-schiff and Grocott-methenamine silver stains revealed chronic granulomatous inflammation with multinucleated giant cells with Paracoccidioides brasiliensis within the cytoplasm, confirming the diagnosis of PCM.

Spacecraft Heat Rejection Methods: Active and Passive Heat Transfer for Electronic Systems.

DTIC Science & Technology

1986-08-29

Storage in avionics, spacecraft and electronics ,;"ters. Microencapsulated phase change materials (PCMs) in a two-component water SlUrrv- were useo with...capsules was observed in the pumping process. Inaddition, both microencapsulated and pure PCM were used to passively reduce tile tempera- tuo .tremes of...conducted as a Phase I Small Business Innovation Research (SBIR) program to explore the feasibility of using microencapsulated phase change materials (PCM) in

Numerical modeling of a finned PCM heat sink

NASA Astrophysics Data System (ADS)

Kozak, Y.; Ziskind, G.

2012-09-01

Phase-change materials (PCMs) can absorb large amounts of heat without significant rise of their temperature during the melting process. This effect is attractive for using in thermal energy storage and passive thermal management. One of the techniques enhance the rate of heat transfer into PCMs is by using fins made of a thermally high conductive material. This paper deals with numerical modeling of a finned PCM-based heat sink. Heat is dissipated on the heat sink base and may be either absorbed by the PCM stored in compartments with conducting walls, or dissipated to the air using fins, or both. A detailed analysis had been done by means of a complete solution of the governing multi-dimensional conservation equations, taking into account convection in the melt, density and volume change due to phase change and temperature variation, motion of solid in the liquid, and other associated phenomena.

First principles investigation of the unipolar resistive switching mechanism in an interfacial phase change memory based on a GeTe/Sb2Te3 superlattice

NASA Astrophysics Data System (ADS)

Shirakawa, Hiroki; Araidai, Masaaki; Shiraishi, Kenji

2018-04-01

The interfacial phase change memory (iPCM) based on a GeTe/Sb2Te3 superlattice is one of the candidates for future storage class memories. However, the atomic structures of the high and low resistance states (HRS/LRS) remain unclear and the resistive switching mechanism is still under debate. Clarifying the switching mechanism is essential for developing further high-reliability and low-power-consumption iPCM. We propose, on the basis of the results of first-principles molecular dynamics simulations, a mechanism for resistive switching, and describe the atomic structures of the high and low resistance states of iPCM for unipolar switching. Our simulations indicated that switching from HRS to LRS occurs with Joule heating only, while that from LRS to HRS occurs with both hole injection and Joule heating.

A numerical study of latent thermal energy storage in a phase change material/carbon panel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mekaddem, Najoua, E-mail: mekaddem.najoua@gmail.com; Ali, Samia Ben, E-mail: samia.benali@enig.rnu.tn; Hannachi, Ahmed, E-mail: ahmed.hannachi@enig.rnu.tn

2016-07-25

To reduce the energetic dependence of building, it has become necessary to explore and develop new materials promoting energy conservation. Because of their high storage capacity, phase change materials (PCMs) are efficient to store thermal energy. In this paper, a 3D model was studied for simulation of energy storing cycles to predict the performances of PCM loaded panels. Carbon was used as supporting material for the PCM. The simulation was based on the enthalpy method using Ansys Fluent software. The panel was exposed to a daily heat flow including the effects of convection and radiation. The results show that themore » temperature decreased of approximately 2.5°C with a time shift about 2 hours. The steady state was reached after four cycles. Thus, after four cycles the PCM showed its effects on the temperature conditioning.« less

On the Behavior of Different PCMs in a Hot Water Storage Tank against Thermal Demands.

PubMed

Porteiro, Jacobo; Míguez, José Luis; Crespo, Bárbara; de Lara, José; Pousada, José María

2016-03-21

Advantages, such as thermal storage improvement, are found when using PCMs (Phase Change Materials) in storage tanks. The inclusion of three different types of materials in a 60 l test tank is studied. Two test methodologies were developed, and four tests were performed following each methodology. A thermal analysis is performed to check the thermal properties of each PCM. The distributions of the water temperatures inside the test tanks are evaluated by installing four Pt-100 sensors at different heights. A temperature recovery is observed after exposing the test tank to an energy demand. An energetic analysis that takes into account the energy due to the water temperature, the energy due to the PCM and the thermal loss to the ambient environment is also presented. The percentage of each PCM that remains in the liquid state after the energy demand is obtained.

Experimental research in the phase change materials based on paraffin and expanded perlite

NASA Astrophysics Data System (ADS)

Jiesheng, Liu; Faping, Li; Xiaoqiang, Gong; Rongtang, Zhang

2018-06-01

In this study, paraffin (PA)/expanded perlite (EP) form-stable phase change material (PCM) was first fabricated using the direct impregnation method without vacuum treatment. Absorptive capacity results showed that the PA/EP composite can obtain good absorptive capacity with the temperature 80 °C and the time 2 h. Compared with the water absorption of EP, the decrease in the water absorption of PA/EP form-stable proved that the absorption of PA into porous EP has been carried out successfully. Scanning electron microscope (SEM) and Fourier transform infrared (FT-IR) results show that paraffin can be well impregnated into EP pores and has good compatibility with it. Differential scanning calorimetry (DSC) results reveal that paraffin/EP composite PCM has melting temperature and latent heat of 53.6 °C and 91.3 J/g, respectively. The durability cycles results suggest that form-stable PA/EP PCM shows good durability.

Evo-devo models of tooth development and the origin of hominoid molar diversity

PubMed Central

Bailey, Shara E.; Schwartz, Gary T.; Skinner, Matthew M.

2018-01-01

The detailed anatomical features that characterize fossil hominin molars figure prominently in the reconstruction of their taxonomy, phylogeny, and paleobiology. Despite the prominence of molar form in human origins research, the underlying developmental mechanisms generating the diversity of tooth crown features remain poorly understood. A model of tooth morphogenesis—the patterning cascade model (PCM)—provides a developmental framework to explore how and why the varying molar morphologies arose throughout human evolution. We generated virtual maps of the inner enamel epithelium—an indelibly preserved record of enamel knot arrangement—in 17 living and fossil hominoid species to investigate whether the PCM explains the expression of all major accessory cusps. We found that most of the variation and evolutionary changes in hominoid molar morphology followed the general developmental rule shared by all mammals, outlined by the PCM. Our results have implications for the accurate interpretation of molar crown configuration in hominoid systematics. PMID:29651459

Relative complexation energies for Li(+) ion in solution: molecular level solvation versus polarizable continuum model study.

PubMed

Eilmes, Andrzej; Kubisiak, Piotr

2010-01-21

Relative complexation energies for the lithium cation in acetonitrile and diethyl ether have been studied. Quantum-chemical calculations explicitly describing the solvation of Li(+) have been performed based on structures obtained from molecular dynamics simulations. The effect of an increasing number of solvent molecules beyond the first solvation shell has been found to consist in reduction of the differences in complexation energies for different coordination numbers. Explicit-solvation data have served as a benchmark to the results of polarizable continuum model (PCM) calculations. It has been demonstrated that the PCM approach can yield relative complexation energies comparable to the predictions based on molecular-level solvation, but at significantly lower computational cost. The best agreement between the explicit-solvation and the PCM results has been obtained when the van der Waals surface was adopted to build the molecular cavity.

On the Behavior of Different PCMs in a Hot Water Storage Tank against Thermal Demands

PubMed Central

Porteiro, Jacobo; Míguez, José Luis; Crespo, Bárbara; de Lara, José; Pousada, José María

2016-01-01

Advantages, such as thermal storage improvement, are found when using PCMs (Phase Change Materials) in storage tanks. The inclusion of three different types of materials in a 60 𝓁 test tank is studied. Two test methodologies were developed, and four tests were performed following each methodology. A thermal analysis is performed to check the thermal properties of each PCM. The distributions of the water temperatures inside the test tanks are evaluated by installing four Pt-100 sensors at different heights. A temperature recovery is observed after exposing the test tank to an energy demand. An energetic analysis that takes into account the energy due to the water temperature, the energy due to the PCM and the thermal loss to the ambient environment is also presented. The percentage of each PCM that remains in the liquid state after the energy demand is obtained. PMID:28773339

Modelling and simulation of “Free Cooling” process applied to building construction

NASA Astrophysics Data System (ADS)

Ousegui, A.; Asbik, M.

2018-05-01

Thermal energy storage systems (TES), using phase change material (PCM) in building walls, consists a hot topic within the research community currently. In the present work, a numerical model is developed to simulate free cooling of air-PCM heat exchanger in both charging and discharging steps. The studied case is taken from experimental work. The domain consists in two parallel plates made of Paraffin as PCM, separate by a gap where air circulates. The flow and temperature can be adjusted. The goal is to calculate the temperature of the air at the outlet, in order to analyse the performance of the device. A good agreement was founded between experimental and numerical results. The analysis of the influence of the flow rate on the efficiency of the process confirms a previous works, that the heating flow rate should be higher than cooling one.

Photocurrent measurements of pentacene-based devices

NASA Astrophysics Data System (ADS)

Masurkar, Amrita; Kymissis, Ioannis

2015-09-01

Photocurrent spectroscopy (PCS) and photocurrent microscopy (PCM) are powerful tools that can probe the underlying mechanisms of charge generation and transport in organic semiconductor devices. There has been significant progress in the use of these techniques, which has yielded a number of insights into the underlying materials and operation of the devices. Despite the potential for PCS and PCM to become standard tools, however, a consensus has not been reached on (1) its uses and (2) the underlying mechanisms which produce the photoresponse. This is particularly true for measurements of pentacene devices, as the energy dynamics of pentacene are complex. Accordingly, here we report the current body of PCS and PCM of pentacene devices, offer interpretations of the data, and discuss which questions remain unanswered. We have divided the reviewed work into four categories based on the goals of the study and the technique used: photocurrent spectroscopy, scanning photocurrent microscopy, mobility, and trap density-of-states.

Automatic neuron segmentation and neural network analysis method for phase contrast microscopy images.

PubMed

Pang, Jincheng; Özkucur, Nurdan; Ren, Michael; Kaplan, David L; Levin, Michael; Miller, Eric L

2015-11-01

Phase Contrast Microscopy (PCM) is an important tool for the long term study of living cells. Unlike fluorescence methods which suffer from photobleaching of fluorophore or dye molecules, PCM image contrast is generated by the natural variations in optical index of refraction. Unfortunately, the same physical principles which allow for these studies give rise to complex artifacts in the raw PCM imagery. Of particular interest in this paper are neuron images where these image imperfections manifest in very different ways for the two structures of specific interest: cell bodies (somas) and dendrites. To address these challenges, we introduce a novel parametric image model using the level set framework and an associated variational approach which simultaneously restores and segments this class of images. Using this technique as the basis for an automated image analysis pipeline, results for both the synthetic and real images validate and demonstrate the advantages of our approach.

A solar air collector with integrated latent heat thermal storage

NASA Astrophysics Data System (ADS)

Charvat, Pavel; Ostry, Milan; Mauder, Tomas; Klimes, Lubomir

2012-04-01

Simulations of the behaviour of a solar air collector with integrated latent heat thermal storage were performed. The model of the collector was created with the use of coupling between TRNSYS 17 and MATLAB. Latent heat storage (Phase Change Material - PCM) was integrated with the solar absorber. The model of the latent heat storage absorber was created in MATLAB and the model of the solar air collector itself was created in TRNSYS with the use of TYPE 56. The model of the latent heat storage absorber allows specification of the PCM properties as well as other parameters. The simulated air collector was the front and back pass collector with the absorber in the middle of the air cavity. Two variants were considered for comparison; the light-weight absorber made of sheet metal and the heat-storage absorber with the PCM. Simulations were performed for the climatic conditions of the Czech Republic (using TMY weather data).

High rate data acquisition from Spacelab/Shuttle

NASA Technical Reports Server (NTRS)

Coffey, R.

1978-01-01

The need for high data rates from a variety of experiments on Spacelab/Shuttle produced the requirement for the Spacelab High Rate Multiplexer/Demultiplexer system. This system acquires serial digital data at asynchronous bit rates from up to sixteen experiments, two data buses, three voice links, two tape recorders, and a universal time channel. Experiment data rates may vary from 200 bps to 16 Mbps while recorded data rates range from 250 Kbps to 32 Mbps. The High Rate Multiplexer (HRM) accepts these data inputs and forms a serial PCM output at flexible rates up to 48 Mbps. This PCM output is transmitted to ground by a Ku-Band RF link via the Tracking and Data Relay Satellite System (TDRSS) or recorded on board for delayed transmission. A complementary ground based High Rate Demultiplexer (HRDM) accepts and demultiplexes the composite PCM data at ground processing locations.

Coordinated regulation of photosynthesis in rice increases yield and tolerance to environmental stress

PubMed Central

Ambavaram, Madana M. R.; Basu, Supratim; Krishnan, Arjun; Ramegowda, Venkategowda; Batlang, Utlwang; Rahman, Lutfor; Baisakh, Niranjan; Pereira, Andy

2014-01-01

Plants capture solar energy and atmospheric carbon dioxide (CO2) through photosynthesis, which is the primary component of crop yield, and needs to be increased considerably to meet the growing global demand for food. Environmental stresses, which are increasing with climate change, adversely affect photosynthetic carbon metabolism (PCM) and limit yield of cereals such as rice (Oryza sativa) that feeds half the world. To study the regulation of photosynthesis, we developed a rice gene regulatory network and identified a transcription factor HYR (HIGHER YIELD RICE) associated with PCM, which on expression in rice enhances photosynthesis under multiple environmental conditions, determining a morpho-physiological programme leading to higher grain yield under normal, drought and high-temperature stress conditions. We show HYR is a master regulator, directly activating photosynthesis genes, cascades of transcription factors and other downstream genes involved in PCM and yield stability under drought and high-temperature environmental stress conditions. PMID:25358745

Piezoelectric crystal microbalance measurements of enthalpy of sublimation of C2-C9 dicarboxylic acids

NASA Astrophysics Data System (ADS)

Dirri, F.; Palomba, E.; Longobardo, A.; Zampetti, E.

2015-07-01

We present here a novel experimental setup able to measure the enthalpy of sublimation of a given compound by means of Piezoelectric Crystal Microbalances (PCM). This experiment was performed in the TG-Lab facility in IAPS-INAF, dedicated to the development of TGA sensors for space measurements, such as detection of organic and non-organic volatile species and refractory materials in planetary environments. In order to study physical-chemical processes concerning the Volatile Organic Compounds (VOC) present in atmospheric environments, the setup has been tested on Dicarboxylic acids. Acids with low molecular weight are among the components of organic fraction of particulate matter in the atmosphere, coming from different sources (biogenic and anthropogenic). Considering their relative abundance, it is useful to consider Dicarboxylic acid as "markers" to define the biogenic or anthropogenic origin of the aerosol, thus obtaining some information of the emission sources. In this work, a temperature controlled effusion cell was used to sublimate VOC, creating a molecular flux that was collimated onto a cold PCM. The VOC re-condensed onto the PCM quartz crystal allowing the determination of the deposition rate. From the measurements of deposition rates, it was possible to infer the enthalpy of sublimation of Adipic acid, i.e. Δ Hsub: 141.6 ± 0.8 kJ mol-1, Succinic acid, i.e. 113.3 ± 1.3 kJ mol-1, Oxalic acid, i.e. 62.5 ± 3.1 kJ mol-1 and Azelaic acid, i.e. 124.2 ± 1.2 kJ mol-1 (weight average values). The results obtained are in very good agreement with literature within 10 % for the Adipic, Succinic and Oxalic acid.

Upper ocean moored current and density profiler applied to winter conditions near Bermuda

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eriksen, C.C.; Dahlen, J.M.; Shillingford, J.T. Jr.

1982-09-20

A new moored instrument which makes repeated high vertical resolution profiles of current, temperature, and salinity in the upper ocean over extended periods was used to observe midwinter conditions near Bermuda. The operation and performance of the instrument, called the profiling current meter (PCM), in the surface wave environment of winter storms is reported here. The PCM profiles along the upper portion of a slightly subsurface mooring by adjusting its buoyancy under computer control. This design decouples the instrument from vertical motions of the mooring induced by surface waves, so that its electromagnetic current sensor operates in a favorable mean-to-fluctuatingmore » flow regime. Current, temperature, and electrical conductivity are (vector) averaged into contiguous preselected bins several meters wide over the possible profile range of 20- to 250-m depth. The PCM is capable of collecting 1000--4000 profiles in a 6- to 12-month period, depending on depth range and ambient currents. A variety of baroclinic motions are evident in the Bermuda observations. Upper ocean manifestations of both Kelvin and superinertial island-trapped waves dominate longshore currents. Vertical coherence of onshore current and temperature suggest that internal wave vertical wave number energy distribution is independent of frequency but modified by island bathymetry. Kinetic energy in shear integrated over a 115.6-m-thick layer in the upper ocean is limited to values less than or equal to the potential energy required to mix the existing stratification. Mixing events occur when kinetic energy associated with shear drives the bulk Richardson number (defined by the ratio of energy integrals over the range profiles) to unity, where it remains while shear and stratification disappear together.« less

Previous exposure to musical auditory stimulation immediately influences the cardiac autonomic responses to the postural change maneuver in women.

PubMed

de Castro, Bianca Cr; Guida, Heraldo L; Roque, Adriano L; de Abreu, Luiz Carlos; Ferreira, Lucas L; Raimundo, Rodrigo D; Monteiro, Carlos Bm; Goulart, Flávia C; Ferreira, Celso; Marcomini, Renata S; Ribeiro, Vivian F; Ré, Alessandro Hn; Vanderlei, Luiz Carlos M; Valenti, Vitor E

2013-08-14

Chronic exposure to musical auditory stimulation has been reported to improve cardiac autonomic regulation. However, it is not clear if music acutely influences it in response to autonomic tests. We evaluated the acute effects of music on heart rate variability (HRV) responses to the postural change maneuver (PCM) in women. We evaluated 12 healthy women between 18 and 28 years old and HRV was analyzed in the time (SDNN, RMSSD, NN50 and pNN50) and frequency (LF, HF and LF/HF ratio) domains. In the control protocol, the women remained at seated rest for 10 minutes and quickly stood up within three seconds and remained standing still for 15 minutes. In the music protocol, the women remained at seated rest for 10 minutes, were exposed to music for 10 minutes and quickly stood up within three seconds and remained standing still for 15 minutes. HRV was recorded at the following time: rest, music (music protocol) 0-5, 5-10 and 10-15 min during standing. In the control protocol the SDNN, RMSSD and pNN50 indexes were reduced at 10-15 minutes after the volunteers stood up, while the LF (nu) index was increased at the same moment compared to seated rest. In the protocol with music, the indexes were not different from control but the RMSSD, pNN50 and LF (nu) were different from the music period. Musical auditory stimulation attenuates the cardiac autonomic responses to the PCM.

Solar wind ion density variations that preceded the M6+ earthquakes occurring on a global scale between 3 and 15 September 2013

NASA Astrophysics Data System (ADS)

Cataldi, Gabriele; Cataldi, Daniele; Straser, Valentino

2015-04-01

Between 3 and 15 September 2013 on Earth were recorded nine M6+ earthquakes: Canada M6,1 earthquake occurred on 3 September at 20:19 UTC; Japan M6,5 earthquake occurred on 4 September at 00:18 UTC; Canada M6,0 earthquake occurred on 4 September at 00:23 UTC; Alaska M6,5 earthquake occurred on 4 September at 02:32 UTC; Alaska M6,0 earthquake occurred on 4 September at 06:27 UTC; Northern Mid-Atlantic Ridge M6,0 earthquake occurred on 5 September at 04:01 UTC; Guatemala M6,4 earthquake occurred on 7 September at 00:13 UTC; Central East Pacific Rise M6,1 earthquake occurred on 11 September at 12:44 UTC; Alaska M6,1 earthquake occurred on 15 September at 16:21 UTC. The authors analyzed the modulation of solar wind ion density during the period from 1 to 18 September 2013 to determine whether the nine earthquakes were preceded by a variations of the solar wind ion density and for testing a method to be applied in the future also for the prediction of tsunami. The data on ion density used to realize the correlation study are represented by: solar wind ion density variation detected by ACE (Advanced Composition Explorer) Satellite, in orbit near the L1 Lagrange point, at 1.5 million of km from Earth, in direction of the Sun. The instrument used to perform the measurement of the solar wind ion density is the Electron, Proton, and Alpha Monitor (EPAM) instrument, equipped on the ACE Satellite. To conduct the study, the authors have taken in consideration the variation of the solar wind protons density that have these characteristics: differential proton flux 1060-1900 keV (p/cm^2-sec-ster-MeV); differential proton flux 761-1220 keV (p/cm^2-sec-ster-MeV); differential proton flux 310-580 keV (p/cm^2-sec-ster-MeV) and differential proton flux 115-195 keV (p/cm^2-sec-ster-MeV). This data set has been marked with the times (time markers) of M6+ earthquakes occurred on a global scale (the data on M6+ seismic activity are provided in real time by USGS, INGV and the CSEM) between 3 and 15 September 2013. The result of the analysis showed that the nine M6+ earthquakes occurred on a global scale in the time period taken as a reference, were preceded by a significant variation of the solar wind proton density to which was superimposed on a coronal mass ejection (CME) that reached the Earth on September 1, 2013 at 09:19 UTC (± 6 hours, iSWA data). The CME event preceded the first earthquake taken in reference (Canada M6,1 earthquake occurred on September 3 at 20:19 UTC) of about 59 hours.

Disseminated paracoccidioidomycosis diagnosis based on oral lesions.

PubMed

Webber, Liana Preto; Martins, Manoela Domingues; de Oliveira, Márcia Gaiger; Munhoz, Etiene Andrade; Carrard, Vinicius Coelho

2014-04-01

Paracoccidioidomycosis (PCM) is a deep mycosis with primary lung manifestations that may present cutaneous and oral lesions. Oral lesions mimic other infectious diseases or even squamous cell carcinoma, clinically and microscopically. Sometimes, the dentist is the first to detect the disease, because lung lesions are asymptomatic, or even misdiagnosed. An unusual case of PCM with 5 months of evolution presenting pulmonary, oral, and cutaneous lesions that was diagnosed by the dentist based on oral lesions is presented and discussed.

PARACOCCIDIOIDOMYCOSIS IN A RENAL TRANSPLANT RECIPIENT

PubMed Central

GÓES, Heliana Freitas de Oliveira; DURÃES, Sandra Maria Barbosa; LIMA, Caren dos Santos; de SOUZA, Mariana Boechat; VILAR, Enoi Aparecida Guedes; DALSTON, Marcos Olivier

2016-01-01

Paracoccidioidomycosis (PCM) is the most common endemic mycosis in Latin America. The etiological agents, which comprise two species, Paracoccidioides brasiliensis and P. lutzii, are thermodimorphic fungi that usually affect previously healthy adults. They primarily involve the lungs and then disseminate to other organs. Such mycosis is rare in organ transplant recipients; there have been only three cases reported in literature, until now. We report a case of PCM in a renal transplant recipient with an unusual dermatological presentation. PMID:26910451

Nonlinear functional for solvation in Density Functional Theory

NASA Astrophysics Data System (ADS)

Gunceler, Deniz; Sundararaman, Ravishankar; Schwarz, Kathleen; Letchworth-Weaver, Kendra; Arias, T. A.

2013-03-01

Density functional calculations of molecules and surfaces in a liquid can accelerate the development of many technologies ranging from solar energy harvesting to lithium batteries. Such studies require the development of robust functionals describing the liquid. Polarizable continuum models (PCM's) have been applied to some solvated systems; but they do not sufficiently capture solvation effects to describe highly polar systems like surfaces of ionic solids. In this work, we present a nonlinear fluid functional within the framework of Joint Density Functional Theory. The fluid is treated not as a linear dielectric, but as a distribution of dipoles that responds to the solute, which we describe starting from the exact free energy functional for point dipoles. We also show PCM's can be recovered as the linear limit of our functional. Our description is of similar computational cost to PCM's, and captures complex solvation effects like dielectric saturation without requiring new fit parameters. For polar and nonpolar molecules, it achieves millihartree level agreement with experimental solvation energies. Furthermore, our functional now makes it possible to investigate chemistry on the surface of lithium battery materials, which PCM's predict to be unstable. Supported as part of the Energy Materials Center at Cornell, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under Award Number DE-SC0001086

Form-Stable Phase Change Materials Based on Eutectic Mixture of Tetradecanol and Fatty Acids for Building Energy Storage: Preparation and Performance Analysis

PubMed Central

Huang, Jingyu; Lu, Shilei; Kong, Xiangfei; Liu, Shangbao; li, Yiran

2013-01-01

This paper is focused on preparation and performance analysis of a series of form-stable phase change materials (FSPCMs), based on eutectic mixtures as phase change materials (PCMs) for thermal energy storage and high-density polyethylene (HDPE)-ethylene-vinyl acetate (EVA) polymer as supporting materials. The PCMs were eutectic mixtures of tetradecanol (TD)–capric acid (CA), TD–lauric acid (LA), and TD–myristic acid (MA), which were rarely explored before. Thermal properties of eutectic mixtures and FSPCMs were measured by differential scanning calorimeter (DSC). The onset melting/solidification temperatures of form-stable PCMs were 19.13 °C/13.32 °C (FS TD–CA PCM), 24.53 °C/24.92 °C (FS TD–LA PCM), and 33.15 °C/30.72 °C (FS TD–MA PCM), respectively, and latent heats were almost greater than 90 J/g. The surface morphologies and chemical stability of form-stable PCM were surveyed by scanning electron microscopy (SEM) and Fourier-transform infrared (FT-IR) spectroscopy, respectively. The thermal cycling test revealed that the thermal reliability of these three form-stable PCMs was good. Thermal storage/release experiment indicated melting/solidification time was shortened by introducing 10 wt % aluminum powder (AP). It is concluded that these FSPCMs can act as potential building thermal storage materials in terms of their satisfactory thermal properties. PMID:28788358

Characteristics and performance of lanthanum gallate electrolyte-supported SOFC under ethanol steam and hydrogen

NASA Astrophysics Data System (ADS)

Huang, Bo; Zhu, Xin-Jian; Hu, Wan-Qi; Yu, Qing-Chun; Tu, Heng-Yong

This study is focused on the electrochemical performance of perovskite-type materials based on doped LaGaO 3. La 0.8Sr 0.2Ga 0.8Mg 0.2O 3- δ (LSGM) and La 0.8Sr 0.2Ga 0.8Mg 0.115Co 0.085O 3- δ (LSGMC) were used as electrolytes and (Pr 0.7Ca 0.3) 0.9MnO 3 (PCM) and La 0.75Sr 0.25Cr 0.5Mn 0.5O 3- δ (LSCM) as cathode and anode material, respectively. LSGM and LSGMC electrolytes were prepared by tape casting with a thickness of about 600 μm. The performance of LSCM/LSGMC/PCM was slightly superior to that obtained on LSCM/LSGM/PCM at different temperatures in both humidified hydrogen and ethanol steam atmospheres, good values of power output in LSCM/LSGMC/PCM were 182 and 169 mW cm -2 using humidified hydrogen and ethanol steam as fuel, respectively, and oxygen as oxidant at 850 °C. Cell stability tests indicate no significant degradation in performance after 60 h of cell testing when LSCM anode was exposed to ethanol steam at 750 °C. Almost no carbon deposits were detected after testing in ethanol steam at 750 °C for >60 h on the LSCM anodes, suggesting that carbon deposition was limited during cell operation.

Evaluation of erythrocyte dysmorphism by light microscopy with lowering of the condenser lens: A simple and efficient method.

PubMed

Barros Silva, Gyl Eanes; Costa, Roberto Silva; Ravinal, Roberto Cuan; Saraiva e Silva, Jucélia; Dantas, Marcio; Coimbra, Terezila Machado

2010-03-01

To demonstrate that the evaluation of erythrocyte dysmorphism by light microscopy with lowering of the condenser lens (LMLC) is useful to identify patients with a haematuria of glomerular or non-glomerular origin. A comparative double-blind study between phase contrast microscopy (PCM) and LMLC is reported to evaluate the efficacy of these techniques. Urine samples of 39 patients followed up for 9 months were analyzed, and classified as glomerular and non-glomerular haematuria. The different microscopic techniques were compared using receiver-operator curve (ROC) analysis and area under curve (AUC). Reproducibility was assessed by coefficient of variation (CV). Specific cut-offs were set for each method according to their best rate of specificity and sensitivity as follows: 30% for phase contrast microscopy and 40% for standard LMLC, reaching in the first method the rate of 95% and 100% of sensitivity and specificity, respectively, and in the second method the rate of 90% and 100% of sensitivity and specificity, respectively. In ROC analysis, AUC for PCM was 0.99 and AUC for LMLC was 0.96. The CV was very similar in glomerular haematuria group for PCM (35%) and LMLC (35.3%). LMLC proved to be effective in contributing to the direction of investigation of haematuria, toward the nephrological or urological side. This method can substitute PCM when this equipment is not available.