High-Lift System for a Supercritical Airfoil: Simplified by Active Flow Control

NASA Technical Reports Server (NTRS)

Melton, LaTunia Pack; Schaeffler, Norman W.; Lin, John C.

2007-01-01

Active flow control wind tunnel experiments were conducted in the NASA Langley Low-Turbulence Pressure Tunnel using a two-dimensional supercritical high-lift airfoil with a 15% chord hinged leading-edge flap and a 25% chord hinged trailing-edge flap. This paper focuses on the application of zero-net-mass-flux periodic excitation near the airfoil trailing edge flap shoulder at a Mach number of 0.1 and chord Reynolds numbers of 1.2 x 10(exp 6) to 9 x 10(exp 6) with leading- and trailing-edge flap deflections of 25 deg. and 30 deg., respectively. The purpose of the investigation was to increase the zero-net-mass-flux options for controlling trailing edge flap separation by using a larger model than used on the low Reynolds number version of this model and to investigate the effect of flow control at higher Reynolds numbers. Static and dynamic surface pressures and wake pressures were acquired to determine the effects of flow control on airfoil performance. Active flow control was applied both upstream of the trailing edge flap and immediately downstream of the trailing edge flap shoulder and the effects of Reynolds number, excitation frequency and amplitude are presented. The excitations around the trailing edge flap are then combined to control trailing edge flap separation. The combination of two closely spaced actuators around the trailing-edge flap knee was shown to increase the lift produced by an individual actuator. The phase sensitivity between two closely spaced actuators seen at low Reynolds number is confirmed at higher Reynolds numbers. The momentum input required to completely control flow separation on the configuration was larger than that available from the actuators used.

Comparing impacts between formal and informal recreational trails.

PubMed

Pickering, Catherine Marina; Norman, Patrick

2017-05-15

Globally there are hundreds of thousands of kilometres of recreational trails traversing natural areas of high conservation value: but what are their impacts and do impacts differ among trails? We compared the effects of four common types of recreational trails [(1) narrow and (2) medium width informal bare earth trails and (3) gravel and (4) tarmac/concrete formal trails] on vegetation adjacent to trails in a high conservation value plant community that is popular for mountain biking and hiking in Australia. Plant species composition was recorded in quadrats along the edge of the four types of trails and in control sites away from trails. Vegetation cover, the cover of individual growth forms, and species richness along the edges of all four types of trails were similar to the controls, although the wider trails affected plant composition, with the tarmac and gravel trails favouring different species. With very few comparative studies, more research is required to allow managers and researchers to directly compare differences in the severity and types of impacts on vegetation among trails. In the meantime, limiting damage to vegetation on the edge of hardened trails during construction, use and maintenance is important, and hardening trails may not always be appropriate. Copyright © 2016. Published by Elsevier Ltd.

The effect of a trail use intervention on urban trail use in Southern Nevada.

PubMed

Clark, Sheila; Bungum, Tim; Shan, Guogen; Meacham, Mindy; Coker, Lisa

2014-10-01

Communities are building or improving trail networks for biking and walking to encourage physical activity, but the relationship between trail environments and physical activity is not well understood. We examined the effect of a trail use intervention in Southern Nevada. We monitored the usage of urban trails (n=10) in Southern Nevada before, during, and after an intervention which included a marketing campaign promoting trail use and the addition of way-finding and incremental distance signage to selected trails (October 2011-October 2012). Data were collected with infrared monitors placed on the trails for three periods of 7days. We compared pre-, mid-, and post-intervention usage rates on the 6 trails where signage was added to usage rates on the 4 control trails. The groups of trails experienced different patterns of increases and decreases over the 1-year study period. Mean users per hour increased 31% for the study trails and 35% for the control trails (p<0.001), but the total increase did not vary between the groups. Trail use increased about 33% during the 1-year study period for the intervention. Adding wayfinding and incremental distance signage appeared to support the increase in usage which followed the marketing campaign. Copyright © 2014 Elsevier Inc. All rights reserved.

Etude de l'effet du gonflement par les solvants sur les proprietes du caoutchouc butyle

NASA Astrophysics Data System (ADS)

Nohile, Cedrick

Polymers and in particular elastomers are widely used for personal protective equipment against chemical and biological hazards. Among them, butyl rubber is one of the most effective elastomers against chemicals. However, if this rubber has a very good resistance to a wide range of them, it is sensitive to non polar solvents. These solvents will easily swell the material and may dramatically affect its properties. This situation may involve a large risk for. butyl rubber protective equipment users. It is thus essential to improve the understanding of the effect of solvents on the properties of butyl rubber. The research that was carried out had two objectives: to identify the parameters controlling the resistance of butyl rubber to solvents and to study the effect of swelling on the properties of butyl rubber. The results show that the resistance of butyl rubber to solvents appears to be controlled by three main parameters: the chemical class of the solvent, its saturation vapor pressure and its molar volume. In addition, swelling affects butyl rubber mechanical properties in a permanent way. The effects can be attributed to the extraction of plasticizers by the solvent and to the degradation of the physico-chemical structure of the polymer network. This chemical degradation was linked to a phenomenon of differential swelling which seems to be controlled by the solvent flow inside the material. These results question some general beliefs within the field of protection against chemical risks. They also open new perspectives for the development of predictive tools relative to the behavior of butyl rubber in the presence of solvents

The optimum content of rubber ash in concrete: flexural strength

NASA Astrophysics Data System (ADS)

Senin, M. S.; Shahidan, S.; Shamsuddin, S. M.; Ariffin, S. F. A.; Othman, N. H.; Rahman, R.; Khalid, F. S.; Nazri, F. M.

2017-11-01

Discarded scrap tyres have become one of the major environmental problems nowadays. Several studies have been carried out to reuse waste tires as an additive or sand replacement in concrete with appropriate percentages of tire rubber, called as rubberized concrete to solve this problem. The main objectives of this study are to investigate the flexural strength performance of concrete when adding the rubber ash and also to analyse the optimum content of rubber ash in concrete prisms. The performance total of 30 number of concrete prisms in size of 100mm x 100mm x 500 mm were investigated, by partially replacement of rubber ash with percentage of 0%, 3%, 5%, 7% and 9% from the volume of the sand. The flexural strength is increased when percentage of rubber ash is added 3% from control concrete prism, RA 0 for both concrete prism age, 7 days and 28 days with value 1.21% and 0.976% respectively. However, for RA 5, RA 7 and RA 9, the flexural strength was decreased compared to the control for both age, 7 days and 28 days. In conclusion, 3% is the optimum content of rubber ash in concrete prism for both concrete age

Numerical natural rubber curing simulation, obtaining a controlled gradient of the state of cure in a thick-section part

NASA Astrophysics Data System (ADS)

El Labban, A.; Mousseau, P.; Bailleul, J. L.; Deterre, R.

2007-04-01

Although numerical simulation has proved to be a useful tool to predict the rubber vulcanization process, few applications in the process control have been reported. Because the end-use rubber properties depend on the state of cure distribution in the parts thickness, the prediction of the optimal distribution remains a challenge for the rubber industry. The analysis of the vulcanization process requires the determination of the thermal behavior of the material and the cure kinetics. A nonisothermal vulcanization model with nonisothermal induction time is used in this numerical study. Numerical results are obtained for natural rubber (NR) thick-section part curing. A controlled gradient of the state of cure in the part thickness is obtained by a curing process that consists not only in mold heating phase, but also a forced convection mold cooling phase in order to stop the vulcanization process and to control the vulcanization distribution. The mold design that allows this control is described. In the heating phase, the state of cure is mainly controlled by the chemical kinetics (the induction time), but in the cooling phase, it is the heat diffusion that controls the state of cure distribution. A comparison among different cooling conditions is shown and a good state of cure gradient control is obtained.

Gas turbine bucket wall thickness control

DOEpatents

Stathopoulos, Dimitrios; Xu, Liming; Lewis, Doyle C.

2002-01-01

A core for use in casting a turbine bucket including serpentine cooling passages is divided into two pieces including a leading edge core section and a trailing edge core section. Wall thicknesses at the leading edge and the trailing edge of the turbine bucket can be controlled independent of each other by separately positioning the leading edge core section and the trailing edge core section in the casting die. The controlled leading and trailing edge thicknesses can thus be optimized for efficient cooling, resulting in more efficient turbine operation.

Patients with Ankylosing Spondylitis and Low Disease Activity because of Anti-TNF-Alpha Therapy Have Higher TRAIL Levels Than Controls: A Potential Compensatory Effect

PubMed Central

López-Mejías, Raquel; Rueda-Gotor, Javier; Miranda-Filloy, José A.; Ubilla, Begoña; Carnero-López, Beatriz; Palmou-Fontana, Natalia; Gómez-Acebo, Inés; Blanco, Ricardo; Pina, Trinitario; Ochoa, Rodrigo; González-Juanatey, Carlos; González-Gay, Miguel A.

2014-01-01

Objective. TRAIL is a potential biomarker of cardiovascular (CV) disease. Ankylosing spondylitis (AS) is a chronic inflammatory disease associated with metabolic syndrome (MeS) and accelerated atherosclerosis. We assessed whether disease activity, systemic inflammation, and MeS features were associated with circulating TRAIL levels in AS patients undergoing TNF-α antagonist infliximab therapy and if infliximab infusion modified TRAIL levels. Methods. We measured TRAIL serum levels in 30 nondiabetic AS patients without CV disease undergoing anti-TNF-α therapy, immediately before and after an infliximab infusion, and in 48 matched controls. Correlations of TRAIL levels with disease activity, systemic inflammation and MeS features, adipokines, and biomarkers of endothelial activation were evaluated. Changes in TRAIL levels following anti-TNF-α infusion were analyzed. Results. TRAIL levels were higher in AS patients than controls. TRAIL levels displayed an inverse correlation with total and LDL cholesterol. We observed an inverse correlation with QUICKI and a marginal association with HOMA-IR. We also found an inverse correlation with resistin and a marginal association with apelin and OPN. Anti-TNF-α infusion did not change TRAIL levels after 120′. Conclusion. Elevated TRAIL levels in AS patients may be the result of a compensatory mechanism to reduce CV risk in these patients. PMID:24976690

Non-motorized winter recreation impacts to snowmelt erosion, Tronsen Basin, Eastern Cascades, Washington.

PubMed

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm(2) total erosion occurring on the trail transects and -3.8 ± 2.4 cm(2) total erosion occurring on the control transect (P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm(2) (P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail (R (2) = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Non-motorized Winter Recreation Impacts to Snowmelt Erosion, Tronsen Basin, Eastern Cascades, Washington

NASA Astrophysics Data System (ADS)

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm2 total erosion occurring on the trail transects and -3.8 ± 2.4 cm2 total erosion occurring on the control transect ( P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm2 ( P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail ( R 2 = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Structural design of morphing trailing edge actuated by SMA

NASA Astrophysics Data System (ADS)

Wang, Qi; Xu, Zhiwei; Zhu, Qian

2013-09-01

In this paper, the morphing trailing edge is designed to achieve the up and down deflection under the aerodynamic load. After a detailed and accurate computational analysis to determine the SMA specifications and layout programs, a solid model is created in CATIA and the structures of the morphing wing trailing edge are produced by CNC machining. A set of DSP measurement and control system is designed to accomplish the controlling experiment of the morphing wing trailing edge. At last, via the force analysis, the trailing edge is fabricated with four sections of aluminum alloy, and the arrangement scheme of SMA wires is determined. Experiment of precise control integral has been performed to survey the control effect. The experiment consists of deflection angle tests of the third joint and the integral structure. Primarily, the ultimate deflection angle is tested in these two experiments. Therefore, the controlling experiment of different angles could be performed within this range. The results show that the deflection error is less than 4%and response time is less than 6.7 s, the precise controlling of the morphing trailing edge is preliminary realized.

Comprehensive Aeroelastic Analysis of Helicopter Rotor with Trailing-Edge Flap for Primary Control and Vibration Control

DTIC Science & Technology

2003-01-01

183 3.34 5/rev fixed system hub normal force with 4/rev open loop trailing-edge flap input...184 3.35 5/rev fixed system hub normal force with 5/rev open loop trailing-edge flap input...185 3.36 5/rev fixed system hub normal force with 6/rev open loop trailing-edge flap

Miniature Trailing Edge Effector for Aerodynamic Control

NASA Technical Reports Server (NTRS)

Lee, Hak-Tae (Inventor); Bieniawski, Stefan R. (Inventor); Kroo, Ilan M. (Inventor)

2008-01-01

Improved miniature trailing edge effectors for aerodynamic control are provided. Three types of devices having aerodynamic housings integrated to the trailing edge of an aerodynamic shape are presented, which vary in details of how the control surface can move. A bucket type device has a control surface which is the back part of a C-shaped member having two arms connected by the back section. The C-shaped section is attached to a housing at the ends of the arms, and is rotatable about an axis parallel to the wing trailing edge to provide up, down and neutral states. A flip-up type device has a control surface which rotates about an axis parallel to the wing trailing edge to provide up, down, neutral and brake states. A rotating type device has a control surface which rotates about an axis parallel to the chord line to provide up, down and neutral states.

Exposure to rubber fume and rubber process dust in the general rubber goods, tyre manufacturing and retread industries.

PubMed

Dost, A A; Redman, D; Cox, G

2000-08-01

This study assesses the current patterns and levels of exposure to rubber fume and rubber process dust in the British rubber industry and compares and contrasts the data obtained from the general rubber goods (GRG), retread tire (RT) and new tire (NT) sectors. A total of 179 rubber companies were visited and data were obtained from 52 general rubber goods, 29 retread tire and 7 new tire manufacturers. The survey was conducted using a questionnaire and included a walk-through inspection of the workplace to assess the extent of use of control measures and the nature of work practices being employed. The most recent (predominantly 1995-97) exposure monitoring data for rubber fume and rubber process dust were obtained from these companies; no additional sampling was conducted for the purpose of this study. In addition to the assessment of exposure data, evaluation of occupational hygiene reports for the quality of information and advice was also carried out.A comparison of the median exposures for processes showed that the order of exposure to rubber fume (E, in mg m(-3)) is: E(moulding) (0.40) approximately E(extrusion) (0.33)>E(milling) (0.18) for GRG; E(press) (0. 32)>E(extrusion) (0.19)>E(autoclave) (0.10) for RT; and E(press) (0. 22) approximately E(all other) (0.22) for NT. The order of exposure to rubber fume between sectors was E(GRG) (0.40)>E(RT) (0.32)>E(NT) (0.22). Median exposures to rubber process dust in the GRG was E(weighing) (4.2)>E(mixing) (1.2) approximately E(milling) (0.8) approximately E(extrusion) (0.8) and no significant difference (P=0. 31) between GRG and NT sectors. The findings compare well with the study carried out in the Netherlands [Kromhout et al. (1994), Annals of Occupational Hygiene 38(1), 3-22], and it is suggested that the factors governing the significant differences noted between the three sectors relate principally to the production and task functions and also to the extent of controls employed. Evaluation of occupational hygiene reports indicated a number of shortcomings including lack of suitable and sufficient information with regard to sampling and analytical methods in use, poor sampling strategy, lack of appreciation regarding true rubber process dust, and a poor understanding of the principles of control for substances assigned maximum exposure limits.

In-depth proteome analysis of the rubber particle of Hevea brasiliensis (para rubber tree).

PubMed

Dai, Longjun; Kang, Guijuan; Li, Yu; Nie, Zhiyi; Duan, Cuifang; Zeng, Rizhong

2013-05-01

The rubber particle is a special organelle in which natural rubber is synthesised and stored in the laticifers of Hevea brasiliensis. To better understand the biological functions of rubber particles and to identify the candidate rubber biosynthesis-related proteins, a comprehensive proteome analysis was performed on H. brasiliensis rubber particles using shotgun tandem mass spectrometry profiling approaches-resulting in a thorough report on the rubber particle proteins. A total of 186 rubber particle proteins were identified, with a range in relative molecular mass of 3.9-194.2 kDa and in isoelectric point values of 4.0-11.2. The rubber particle proteins were analysed for gene ontology and could be categorised into eight major groups according to their functions: including rubber biosynthesis, stress- or defence-related responses, protein processing and folding, signal transduction and cellular transport. In addition to well-known rubber biosynthesis-related proteins such as rubber elongation factor (REF), small rubber particle protein (SRPP) and cis-prenyl transferase (CPT), many proteins were firstly identified to be on the rubber particles, including cyclophilin, phospholipase D, cytochrome P450, small GTP-binding protein, clathrin, eukaryotic translation initiation factor, annexin, ABC transporter, translationally controlled tumour protein, ubiquitin-conjugating enzymes, and several homologues of REF, SRPP and CPT. A procedure of multiple reaction monitoring was established for further protein validation. This comprehensive proteome data of rubber particles would facilitate investigation into molecular mechanisms of biogenesis, self-homeostasis and rubber biosynthesis of the rubber particle, and might serve as valuable biomarkers in molecular breeding studies of H. brasiliensis and other alternative rubber-producing species.

Flutter suppression and gust alleviation using active controls

NASA Technical Reports Server (NTRS)

Nissim, E.

1975-01-01

Application of the aerodynamic energy approach to some problems of flutter suppression and gust alleviation were considered. A simple modification of the control-law is suggested for achieving the required pitch control in the use of a leading edge - trailing edge activated strip. The possible replacement of the leading edge - trailing edge activated strip by a trailing edge - tab strip is also considered as an alternate solution. Parameters affecting the performance of the activated leading edge - trailing edge strip were tested on the Arava STOL Transport and the Westwind Executive Jet Transport and include strip location, control-law gains and a variation in the control-law itself.

Recent advances in aerodynamic energy concept for flutter suppression and gust alleviation using active controls

NASA Technical Reports Server (NTRS)

Nissim, E.

1977-01-01

Control laws are derived, by using realizable transfer functions, which permit relaxation of the stability requirements of the aerodynamic energy concept. The resulting aerodynamic eigenvalues indicate that both the trailing edge and the leading edge-trailing edge control systems can be made more effective. These control laws permit the introduction of aerodynamic damping and stiffness terms in accordance with the requirements of any specific system. Flutter suppression and gust alleviation problems can now be treated by either a trailing edge control system or by a leading edge-trailing edge control system by using the aerodynamic energy concept. Results are applicable to a wide class of aircraft operating at subsonic Mach numbers.

Degradation of polyisoprene rubber by newly isolated Bacillus sp. AF-666 from soil.

PubMed

Shah, A A; Hasan, F; Shah, Z; Mutiullah; Hameed, A

2012-01-01

Various microorganisms were screened for their ability to degrade polyisoprene rubber (natural rubber latex gloves). Strain AF-666, newly isolated from a soil sample, was selected as the best strain having the ability to grow on polyisoprene containing plates. The strain identified as Bacillus sp. AF-666, was found to degrade polyisoprene rubber, both on basal agar plates (latex overlay) as well as in liquid medium. Qualitative analysis of degradation was done through scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy SEM showed changes in surface morphology, like appearance of pits and cracks, and marked difference in transmittance spectra of test and control due to changes in the functional groups, was detected through FTIR. CO2 evolution as a result of rubber degradation, was calculated gravimetrically by Sturm Test. About 4.43 g/1 of CO2 was produced in case of test, whereas, 1.57 g/1 in case of control. The viable number of cells (CFU/ml) was also higher in test than in control. Present study may provide an opportunity for further studies on the applications of biotechnological processes as a tool for rubber waste management.

Reverse-micelle-induced porous pressure-sensitive rubber for wearable human-machine interfaces.

PubMed

Jung, Sungmook; Kim, Ji Hoon; Kim, Jaemin; Choi, Suji; Lee, Jongsu; Park, Inhyuk; Hyeon, Taeghwan; Kim, Dae-Hyeong

2014-07-23

A novel method to produce porous pressure-sensitive rubber is developed. For the controlled size distribution of embedded micropores, solution-based procedures using reverse micelles are adopted. The piezosensitivity of the pressure sensitive rubber is significantly increased by introducing micropores. Using this method, wearable human-machine interfaces are fabricated, which can be applied to the remote control of a robot. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hikers and other trail users

Treesearch

Robert C. Lucas

1971-01-01

Trail users seem neglected. Trail systems are limited, largely relics of fire control rather than designed for recreation; and total trail miles are probably declining. On the other hand, participation in various kinds of trail-oriented recreation is substantial and growing. Most activity is for short periods of time close to participants' homes. A varied and...

Rubber dam isolation of cervical lesions. Part 1: Alternative techniques which avoid injury to the periodontium.

PubMed

Liebenberg, W H

1994-01-01

While it is arguable that the operative procedures depicted in this article could have been done equally well with alternative forms of isolation, it is indisputable that rubber dam provides for the most thorough 'isolation' in the comprehensive sense of the term. It allows for the finite control over peripheral variables such as access and controlled gingival retraction. This in turn permits meticulous execution of restorative procedures within the luxury of 'true four-handed dentistry'. Most operative procedures are done within the limitations of single handed dentistry as the other 'three hands' are involved with retraction, fluid evacuation and access control. The rubber dam is indeed indispensable and with the increased awareness of infection control it is conceivable that rubber dam isolation will continue to be associated with quality patient care. Part 2 of this article will detail the application of the 'Modified Gingival Retractor' in the isolation of cervical lesions.

Leaching of nitroso rubber material removes uncured polymer

NASA Technical Reports Server (NTRS)

Bratfisch, W. A.; Gonzalez, R.

1972-01-01

New leaching process removes uncured polymer from nitroso rubber, elastomer used in presence of nitrogen tetroxide. Uncured portion is removed by controlled soaking of polymer slab in Freon TF. Leaching with Freon TF prevents nitroso rubber from adhering to adjoining surfaces and limiting its usefulness in either static or dynamic applications.

40 CFR 428.93 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.93 Effluent limitations guidelines representing... pollutants or pollutant properties, controlled by this section, and attributable to pan, dry digestion, and mechanical reclaimed rubber processes which are integrated with a wet digestion reclaimed rubber process...

40 CFR 428.93 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.93 Effluent limitations guidelines representing... pollutants or pollutant properties, controlled by this section, and attributable to pan, dry digestion, and mechanical reclaimed rubber processes which are integrated with a wet digestion reclaimed rubber process...

40 CFR 428.93 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.93 Effluent limitations guidelines representing... pollutants or pollutant properties, controlled by this section, and attributable to pan, dry digestion, and mechanical reclaimed rubber processes which are integrated with a wet digestion reclaimed rubber process...

Strategy of arm movement control is determined by minimization of neural effort for joint coordination.

PubMed

Dounskaia, Natalia; Shimansky, Yury

2016-06-01

Optimality criteria underlying organization of arm movements are often validated by testing their ability to adequately predict hand trajectories. However, kinematic redundancy of the arm allows production of the same hand trajectory through different joint coordination patterns. We therefore consider movement optimality at the level of joint coordination patterns. A review of studies of multi-joint movement control suggests that a 'trailing' pattern of joint control is consistently observed during which a single ('leading') joint is rotated actively and interaction torque produced by this joint is the primary contributor to the motion of the other ('trailing') joints. A tendency to use the trailing pattern whenever the kinematic redundancy is sufficient and increased utilization of this pattern during skillful movements suggests optimality of the trailing pattern. The goal of this study is to determine the cost function minimization of which predicts the trailing pattern. We show that extensive experimental testing of many known cost functions cannot successfully explain optimality of the trailing pattern. We therefore propose a novel cost function that represents neural effort for joint coordination. That effort is quantified as the cost of neural information processing required for joint coordination. We show that a tendency to reduce this 'neurocomputational' cost predicts the trailing pattern and that the theoretically developed predictions fully agree with the experimental findings on control of multi-joint movements. Implications for future research of the suggested interpretation of the trailing joint control pattern and the theory of joint coordination underlying it are discussed.

Industrywide studies report of an in-depth survey at Copolymer Rubber and Chemical Corporation, Baton Rouge, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishnan, E.R.; Fajen, J.M.

1987-05-08

An in depth industrial hygiene survey was conducted at the Copolymer Rubber and Chemical Corporation located in Baton Rouge, Louisiana. The facility produced styrene-butadiene rubber and nitrile-butadiene rubber by continuous emulsion polymerization. The ultimate use of this product was for the manufacture of tire and rubber products. The authors recommend that leaking pumps which can present a potential for 1,3-butadiene exposure in the tank farm and recovery areas should be controlled through the use of dual mechanical seals. Employees assigned to maintenance tasks should use respirators with organic vapor cartridges.

Primary control of a Mach scale swashplateless rotor using brushless DC motor actuated trailing edge flaps

NASA Astrophysics Data System (ADS)

Saxena, Anand

The focus of this research was to demonstrate a four blade rotor trim in forward flight using integrated trailing edge flaps instead of using a swashplate controls. A compact brushless DC motor was evaluated as an on-blade actuator, with the possibility of achieving large trailing edge flap amplitudes. A control strategy to actuate the trailing edge flap at desired frequency and amplitude was developed and large trailing edge flap amplitudes from the motor (instead of rotational motion) were obtained. Once the actuator was tested on the bench-top, a lightweight mechanism was designed to incorporate the motor in the blade and actuate the trailing edge flaps. A six feet diameter, four bladed composite rotor with motor-flap system integrated into the NACA 0012 airfoil section was fabricated. Systematic testing was carried out for a range of load conditions, first in the vacuum chamber followed by hover tests. Large trailing edge flap deflections were observed during the hover testing, and a peak to peak trailing edge flap amplitude of 18 degree was achieved at 2000 rotor RPM with hover tip Mach number of 0.628. A closed loop controller was designed to demonstrate trailing edge flap mean position and the peak to peak amplitude control. Further, a soft pitch link was designed and fabricated, to replace the stiff pitch link and thereby reduce the torsional stiffness of the blade to 2/rev. This soft pitch link allowed for blade root pitch motion in response to the trailing edge flap inputs. Blade pitch response due to both steady as well as sinusoidal flap deflections were demonstrated. Finally, tests were performed in Glenn L. Martin wind tunnel using a model rotor rig to assess the performance of motor-flap system in forward flight. A swashplateless trim using brushless DC motor actuated trailing edge flaps was achieved for a rotor operating at 1200 RPM and an advance ratio of 0.28. Also, preliminary exploration was carried out to test the scalability of the motor driven trailing edge flap concept. In conclusion, the concept of using brushless DC motors as on-blade actuators, actuating trailing edge flaps has the potential to replace the current mechanically complex swashplate with a hydraulic-free swashplateless system and thereby reduce overall weight and hub drag.

Condoms - male

MedlinePlus

... Rubbers; Male condoms; Contraceptive - condom; Contraception - condom; Barrier method - condom ... infections.) Latex rubber Polyurethane Condoms are the only method of birth control for men that are not ...

THERMOOXIDATIVE STUDY OF RAW NATURAL RUBBER FROM BRAZILIAN IAC 300 SERIES CLONES

USDA-ARS?s Scientific Manuscript database

The improvement of rubber tree species is of key importance due to the worldwide market demand of this renewable material essential for several types of industries. The thermal performance of natural rubber produced from new clones of IAC 300 series, and the Malaysian RRIM 600 clone (used as control...

Impact of the timing and duration of weed control on the establishment of a rubber tree plantation.

PubMed

Guzzo, Caio D; Carvalho, Leonardo B de; Giancotti, Paulo R F; Alves, Pedro L C A; Gonçalves, Elaine C P; Martins, José V F

2014-03-01

Rubber tree production is reduced by weeds that compete for environmental resources; therefore, the timing and duration of weed control influences weed interference. The objectives of this study were to evaluate the growth of rubber tree (Hevea brasiliensis) plants, to determine the critical period for weed control, and to evaluate the growth recovery of rubber trees that coexisted with weeds for different periods of time after planting. Two groups of treatments were established under field conditions in the first year of the investigation: one group contained crescent periods of weed infestation, while the other contained crescent periods of weed control, also including a weed-free check and a total weedy check. In the second year of the investigation, the weeds were totally controlled. Urochloa decumbens was the dominant weed (over 90% groundcover). Crop growth was greatly reduced due to the weed interference. Plant height decreased more rapidly than did any other characteristic. Plant height, leaf dry mass, and leaf area decreased by 99%, 97% and 96%, respectively, and were the most reduced characteristics. Plant height also recovered more rapidly than did any characteristic when the period of weed control was lengthened. However, stem dry mass increased by 750%, making it the most recovered characteristic. The critical period for weed control was between 4 and 9½ months after planting in the first year; however, the rubber trees showed an expressive growth recovery when the weeds were controlled throughout the second year.

30 CFR 57.4057 - Underground trailing cables.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and Control § 57.4057 Underground trailing cables. Underground trailing cables shall be accepted or... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Underground trailing cables. 57.4057 Section 57.4057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 57.4057 - Underground trailing cables.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and Control § 57.4057 Underground trailing cables. Underground trailing cables shall be accepted or... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Underground trailing cables. 57.4057 Section 57.4057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 57.4057 - Underground trailing cables.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and Control § 57.4057 Underground trailing cables. Underground trailing cables shall be accepted or... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Underground trailing cables. 57.4057 Section 57.4057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

30 CFR 57.4057 - Underground trailing cables.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and Control § 57.4057 Underground trailing cables. Underground trailing cables shall be accepted or... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Underground trailing cables. 57.4057 Section 57.4057 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL...

Accurate control of oxygen level in cells during culture on silicone rubber membranes with application to stem cell differentiation.

PubMed

Powers, Daryl E; Millman, Jeffrey R; Bonner-Weir, Susan; Rappel, Michael J; Colton, Clark K

2010-01-01

Oxygen level in mammalian cell culture is often controlled by placing culture vessels in humidified incubators with a defined gas phase partial pressure of oxygen (pO(2gas)). Because the cells are consuming oxygen supplied by diffusion, a difference between pO(2gas) and that experienced by the cells (pO(2cell)) arises, which is maximal when cells are cultured in vessels with little or no oxygen permeability. Here, we demonstrate theoretically that highly oxygen-permeable silicone rubber membranes can be used to control pO(2cell) during culture of cells in monolayers and aggregates much more accurately and can achieve more rapid transient response following a disturbance than on polystyrene and fluorinated ethylene-propylene copolymer membranes. Cell attachment on silicone rubber was achieved by physical adsorption of fibronectin or Matrigel. We use these membranes for the differentiation of mouse embryonic stem cells to cardiomyocytes and compare the results with culture on polystyrene or on silicone rubber on top of polystyrene. The fraction of cells that are cardiomyocyte-like increases with decreasing pO(2) only when using oxygen-permeable silicone membrane-based dishs, which contract on silicone rubber but not polystyrene. The high permeability of silicone rubber results in pO(2cell) being equal to pO(2gas) at the tissue-membrane interface. This, together with geometric information from histological sections, facilitates development of a model from which the pO(2) distribution within the resulting aggregates is computed. Silicone rubber membranes have significant advantages over polystyrene in controlling pO(2cell), and these results suggest they are a valuable tool for investigating pO(2) effects in many applications, such as stem cell differentiation. Copyright 2009 American Institute of Chemical Engineers

Equations and charts for the rapid estimation of hinge-moment and effectiveness parameters for trailing-edge controls having leading and trailing edges swept ahead of the Mach lines

NASA Technical Reports Server (NTRS)

Goin, Kennith L

1951-01-01

Existing conical-flow solutions have been used to calculate the hinge-moments and effectiveness parameters of trailing-edge controls having leading and trailing edges swept ahead of the Mach lines and having streamwise root and tip chords. Equations and detailed charts are presented for the rapid estimation of these parameters. Also included is an approximate method by which these parameters may be corrected for airfoil-section thickness.

Studies on the preparation and uses of Co-60 gamma-ray irradiated natural latex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kartowardoyo, S.; Sundardi, F.

1977-11-01

The properties are described of low-ammonia latex concentrates produced by gamma-ray irradiation (0.5 to 2.0 Mrad dose) in the presence of carbon tetrachloride or chloroform as sensitizer. Dipping trails with irradiated concentrates and irradiated field latex, for the preparation of condoms and medical gloves, gave products with high ultimate elongation, low modulus, and high permanent set. A change from straight dipping to coagulant dipping and a heat treatment after drying resulted in improved physical properties. A notable feature of products prepared from these materials is their purity, i.e., low content of rubber chemicals. An economic disadvantage, at the present time,more » is the high initial cost of the irradiation equipment.« less

Study on cord/rubber interface at elevated temperatures by H-pull test method

NASA Astrophysics Data System (ADS)

Jamshidi, M.; Afshar, F.; Mohammadi, N.; Pourmahdian, S.

2005-08-01

Cords are used as reinforcing materials in rubber compounds. To increase cord/rubber interfacial adhesion, they are coated by an adhesive (usually based on resorcinol-formaldehyde-latex). These composites are used in many sectors such as tire and belt industries. Cord/rubber adhesion strength is an important aspect to determine the durability of system. Due to temperature increase during running tires, the adhesion energy becomes different from initial one. To study cord/rubber interface at elevated temperatures, H-adhesion test method was used. H-pull test is a simple method for adhesion evaluation at ambient temperature, so it is usually used for material quality control. In this research, cord/rubber systems were vulcanized at different temperatures and H-adhesion of samples were evaluated at elevated temperatures. Also cord/rubber interface was studied by ATR analyze to determine interfacial interactions kind.

Assessment of fatigue load alleviation potential through blade trailing edge morphing

NASA Astrophysics Data System (ADS)

Tsiantas, Theofanis; Manolas, Dimitris I.; Machairas, Theodore; Karakalas, Anargyros; Riziotis, Vasilis A.; Saravanos, Dimitrios; Voutsinas, Spyros G.

2016-09-01

The possibility of alleviating wind turbine loads through blade trailing edge shape morphing is investigated in the present paper. Emphasis is put on analyzing the effect of the trailing edge flap geometry on load reduction levels. The choice of the shape deformation of the camber line as well as the chordwise and spanwise dimensions of the trailing edge flap are addressed. The analysis concerns the conceptual DTU 10 MW RWT. Aeroelastic control of loads is materialized through a standard individual flap controller. Furthermore, a comb ined individual pitch-flap controller is evaluated and found to present advantages compared to the flap only controller. Flapwise fatigue load reduction ranging from 10% to 20%, depending on wind velocity and configuration considered, is obtained. Better performance is achieved by the combined pitch-flap controller.

TRAIL Death Receptor-4, Decoy Receptor-1 and Decoy Receptor-2 Expression on CD8+ T Cells Correlate with the Disease Severity in Patients with Rheumatoid Arthritis

PubMed Central

2010-01-01

Background Rheumatoid Arthritis (RA) is a chronic autoimmune inflammatory disorder. Although the pathogenesis of disease is unclear, it is well known that T cells play a major role in both development and perpetuation of RA through activating macrophages and B cells. Since the lack of TNF-Related Apoptosis Inducing Ligand (TRAIL) expression resulted in defective thymocyte apoptosis leading to an autoimmune disease, we explored evidence for alterations in TRAIL/TRAIL receptor expression on peripheral T lymphocytes in the molecular mechanism of RA development. Methods The expression of TRAIL/TRAIL receptors on T cells in 20 RA patients and 12 control individuals were analyzed using flow cytometry. The correlation of TRAIL and its receptor expression profile was compared with clinical RA parameters (RA activity scored as per DAS28) using Spearman Rho Analysis. Results While no change was detected in the ratio of CD4+ to CD8+ T cells between controls and RA patient groups, upregulation of TRAIL and its receptors (both death and decoy) was detected on both CD4+ and CD8+ T cells in RA patients compared to control individuals. Death Receptor-4 (DR4) and the decoy receptors DcR1 and DcR2 on CD8+ T cells, but not on CD4+ T cells, were positively correlated with patients' DAS scores. Conclusions Our data suggest that TRAIL/TRAIL receptor expression profiles on T cells might be important in revelation of RA pathogenesis. PMID:20799941

Study on Trailing Edge Ramp of Supercritical Airfoil

DTIC Science & Technology

2016-03-30

7 th Asia-Pacific International Symposium on Aerospace Technology, 25 – 27 November 2015, Cairns Study on Trailing Edge Ramp of Supercritical...China Abstract Trailing edge flow control method could improve the performance of supercritical airfoil with a small modification on the original...airfoil. In this paper, a ramp of 2%~7% chord length is sliced near the trailing edge to improve airfoil performance. The trailing edge ramp is

The effects of nitrogen fertilization on N2O emissions from a rubber plantation

NASA Astrophysics Data System (ADS)

Zhou, Wen-Jun; Ji, Hong-Li; Zhu, Jing; Zhang, Yi-Ping; Sha, Li-Qing; Liu, Yun-Tong; Zhang, Xiang; Zhao, Wei; Dong, Yu-Xin; Bai, Xiao-Long; Lin, You-Xin; Zhang, Jun-Hui; Zheng, Xun-Hua

2016-06-01

To gain the effects of N fertilizer applications on N2O emissions and local climate change in fertilized rubber (Hevea brasiliensis) plantations in the tropics, we measured N2O fluxes from fertilized (75 kg N ha-1 yr-1) and unfertilized rubber plantations at Xishuangbanna in southwest China over a 2-year period. The N2O emissions from the fertilized and unfertilized plots were 4.0 and 2.5 kg N ha-1 yr-1, respectively, and the N2O emission factor was 1.96%. Soil moisture, soil temperature, and the area weighted mean ammoniacal nitrogen (NH4+-N) content controlled the variations in N2O flux from the fertilized and unfertilized rubber plantations. NH4+-N did not influence temporal changes in N2O emissions from the trench, slope, or terrace plots, but controlled spatial variations in N2O emissions among the treatments. On a unit area basis, the 100-year carbon dioxide equivalence of the fertilized rubber plantation N2O offsets 5.8% and 31.5% of carbon sink of the rubber plantation and local tropical rainforest, respectively. When entire land area in Xishuangbanna is considered, N2O emissions from fertilized rubber plantations offset 17.1% of the tropical rainforest’s carbon sink. The results show that if tropical rainforests are converted to fertilized rubber plantations, regional N2O emissions may enhance local climate warming.

Assessment  of  Genotoxicity  Among  Rubber  Industry Workers  Occupationally  Exposed  to  Toxic  Agents  Using Micronucleus  Assay.

PubMed

Gemitha, Gem; Sudha, Sellappa

2013-01-01

Occupational and environmental exposures mostly represent complexmixture of genotoxic agents, however there is a wide variation in the specificity of biomarkers. Exploration of correlations among biomarkers contributes to the further progress of molecular cancer epidemiology and to the selection of the optimal biomarkers for the investigation of human exposure to carcinogens. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to toxic agents among rubber industry workers by using Micronucleus (MN) assay. In the present study 35 occupationally exposed rubber industry workers and 30 controls were investigated for genetic damage. Both the exposed and control individuals were selected from rural areas of South India. Exfoliated Buccal cells were collected from the study population and examined for the presence of MN. Rubber industry workers showed a significant increase in micronucleated cells when compared to controls with respect to their smoking and drinking habits (P< 0.05). The present study suggested that occupational exposure to toxic chemicals in rubber industry can cause genetic damage. MN formation reflects genetic changes and/or events associated with carcinogenesis. Therefore the results of this study indicate that rubber industry workers may be at the risk of cancer. Therefore, it is important to take appropriate measures to protect the workers from occupational hazards.

[Treatment of Bell's palsy with combination of traditional Chinese medicine and western medicine].

PubMed

Wang, Xiao-hong; Zhang, Li-ming; Han, Mei; Zhang, Ke-qing; Jiang, Jiao-jiao

2004-06-01

To evaluation the clinical effect of combination of traditional Chinese medicine and western medicine on Bell's palsy. 83 patients with Bell's palsy were randomly divided into two groups (trail group 54 cases and control group 29 cases). Patients in two groups were treated with medicine, acupuncture, physiotherapy, while patients in the trail group were treated with massage and functional exercise as the same time. The results of both groups were evaluated according to Portmann's Simple Scale. The score before treatment of trail group was 2.907 +/- 1.794, while control group was 2.931 +/- 2.034. And the score after treatment of trail group was 18.593 +/- 1.743, while control group was 9.862 +/- 3.091. Score of the function of facial muscles obtained from trail group was distinctly higher than that was from the control group (P < 0.01), as well as the improvement index (P < 0.01, trail group: 0.844 +/- 0.095, control group: 0.712 +/- 0.129). There is significant curative effect and suitability in the treatment of Bell's palsy with combination of traditional Chinese medicine and western medicine. The improvement of facial muscles' motive function pre- and post-treatment and quantitative evaluation of curative effect can be objectively obtained by evaluation of facial muscles' function.

Low-Speed Wind-Tunnel Investigation of Blowing Boundary-Layer Control on Leading- and Trailing-Edge Flaps of a Large-Scale, Low-Aspect-Ratio, 45 Swept-wing Airplane Configuration

NASA Technical Reports Server (NTRS)

Maki, Ralph L.

1959-01-01

Blowing boundary-layer control was applied to the leading- and trailing-edge flaps of a 45 deg sweptback-wing complete model in a full-scale low-speed wind-tunnel study. The principal purpose of the study was to determine the effects of leading-edge flap deflection and boundary-layer control on maximum lift and longitudinal stability. Leading-edge flap deflection alone was sufficient to maintain static longitudinal stability without trailing-edge flaps. However, leading-edge flap blowing was required to maintain longitudinal stability by delaying leading-edge flow separation when trailing-edge flaps were deflected either with or without blowing. Partial-span leading-edge flaps deflected 60 deg with moderate blowing gave the major increase in maximum lift, although higher deflection and additional blowing gave some further increase. Inboard of 0.4 semispan leading-edge flap deflection could be reduced to 40 deg and/or blowing could be omitted with only small loss in maximum lift. Trailing-edge flap lift increments were increased by boundary-layer control for deflections greater than 45 deg. Maximum lift was not increased with deflected trailing-edge flaps with blowing.

Low frequency acoustic properties of a honeycomb-silicone rubber acoustic metamaterial

NASA Astrophysics Data System (ADS)

Gao, Nansha; Hou, Hong

2017-04-01

In order to overcome the influence of mass law on traditional acoustic materials and obtain a lightweight thin-layer structure which can effectively isolate the low frequency noises, a honeycomb-silicone rubber acoustic metamaterial was proposed. Experimental results show that the sound transmission loss (STL) of acoustic metamaterial in this paper is greatly higher than that of monolayer silicone rubber metamaterial. Based on the band structure, modal shapes, as well as the sound transmission simulation, the sound insulation mechanism of the designed honeycomb-silicone rubber structure was analyzed from a new perspective, which had been validated experimentally. Side length of honeycomb structure and thickness of the unit structure would affect STL in damping control zone. Relevant conclusions and design method provide a new concept for engineering noise control.

Method for Molding Structural Parts Utilizing Modified Silicone Rubber

NASA Technical Reports Server (NTRS)

Weiser, Erik S. (Inventor); Baucom, Robert M. (Inventor); Snoha, John J. (Inventor)

1998-01-01

This invention improves upon a method for molding structural parts from preform material. Preform material to be used for the part is provided. A silicone rubber composition containing entrained air voids is prepared. The silicone rubber and preform material assembly is situated within a rigid mold cavity used to shape the preform material to die desired shape. The entire assembly is heated in a standard heating device so that the thermal expansion of the silicone rubber exerts the pressure necessary to force the preform material into contact with the mold container. The introduction of discrete air voids into the silicone rubber allows for accurately controlled pressure application on the preform material at the cure temperature.

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials.

PubMed

Yilmaz, Arin; Degirmenci, Nurhayat

2009-05-01

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.

Mechanical properties of concrete containing a high volume of tire-rubber particles.

PubMed

Khaloo, Ali R; Dehestani, M; Rahmatabadi, P

2008-12-01

Due to the increasingly serious environmental problems presented by waste tires, the feasibility of using elastic and flexible tire-rubber particles as aggregate in concrete is investigated in this study. Tire-rubber particles composed of tire chips, crumb rubber, and a combination of tire chips and crumb rubber, were used to replace mineral aggregates in concrete. These particles were used to replace 12.5%, 25%, 37.5%, and 50% of the total mineral aggregate's volume in concrete. Cylindrical shape concrete specimens 15 cm in diameter and 30 cm in height were fabricated and cured. The fresh rubberized concrete exhibited lower unit weight and acceptable workability compared to plain concrete. The results of a uniaxial compressive strain control test conducted on hardened concrete specimens indicate large reductions in the strength and tangential modulus of elasticity. A significant decrease in the brittle behavior of concrete with increasing rubber content is also demonstrated using nonlinearity indices. The maximum toughness index, indicating the post failure strength of concrete, occurs in concretes with 25% rubber content. Unlike plain concrete, the failure state in rubberized concrete occurs gently and uniformly, and does not cause any separation in the specimen. Crack width and its propagation velocity in rubberized concrete are lower than those of plain concrete. Ultrasonic analysis reveals large reductions in the ultrasonic modulus and high sound absorption for tire-rubber concrete.

The rubber tree genome reveals new insights into rubber production and species adaptation.

PubMed

Tang, Chaorong; Yang, Meng; Fang, Yongjun; Luo, Yingfeng; Gao, Shenghan; Xiao, Xiaohu; An, Zewei; Zhou, Binhui; Zhang, Bing; Tan, Xinyu; Yeang, Hoong-Yeet; Qin, Yunxia; Yang, Jianghua; Lin, Qiang; Mei, Hailiang; Montoro, Pascal; Long, Xiangyu; Qi, Jiyan; Hua, Yuwei; He, Zilong; Sun, Min; Li, Wenjie; Zeng, Xia; Cheng, Han; Liu, Ying; Yang, Jin; Tian, Weimin; Zhuang, Nansheng; Zeng, Rizhong; Li, Dejun; He, Peng; Li, Zhe; Zou, Zhi; Li, Shuangli; Li, Chenji; Wang, Jixiang; Wei, Dong; Lai, Chao-Qiang; Luo, Wei; Yu, Jun; Hu, Songnian; Huang, Huasun

2016-05-23

The Para rubber tree (Hevea brasiliensis) is an economically important tropical tree species that produces natural rubber, an essential industrial raw material. Here we present a high-quality genome assembly of this species (1.37 Gb, scaffold N50 = 1.28 Mb) that covers 93.8% of the genome (1.47 Gb) and harbours 43,792 predicted protein-coding genes. A striking expansion of the REF/SRPP (rubber elongation factor/small rubber particle protein) gene family and its divergence into several laticifer-specific isoforms seem crucial for rubber biosynthesis. The REF/SRPP family has isoforms with sizes similar to or larger than SRPP1 (204 amino acids) in 17 other plants examined, but no isoforms with similar sizes to REF1 (138 amino acids), the predominant molecular variant. A pivotal point in Hevea evolution was the emergence of REF1, which is located on the surface of large rubber particles that account for 93% of rubber in the latex (despite constituting only 6% of total rubber particles, large and small). The stringent control of ethylene synthesis under active ethylene signalling and response in laticifers resolves a longstanding mystery of ethylene stimulation in rubber production. Our study, which includes the re-sequencing of five other Hevea cultivars and extensive RNA-seq data, provides a valuable resource for functional genomics and tools for breeding elite Hevea cultivars.

Best management practices for erosion control from bladed skid trails

Treesearch

Charles R. Wade; W. Michael Aust; M. Chad Bolding; William A. Lakel III

2012-01-01

Sediment from forest operations is primarily associated with roads and skid trails. We evaluated five skid trail closure treatments applied to bladed skid trails in the Virginia Piedmont. Closure treatments were Waterbars, Seed, Mulch, Pine slash, and Hardwood slash. Sediment traps were used to collect monthly sediment samples for one year. The Mulch, Pine slash, and...

Preparation of vinyl acetate grafted natural rubber by irradiation method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porntrairat, A.; Pattamaprom, C.

Improvement in properties of natural rubber could be done by several methods. In this research, gamma radiation technique, which is simple, accurate, easy to control and clean, was applied to enhance the properties of natural rubber (NR) in latex state. The purpose of this research is to study the appropriate condition for preparing grafted natural rubber latex by using irradiation method. Vinyl acetate monomers (VAc) were grafted onto natural rubber latex (NR-g-PVAc) at 0-10 kGys by gamma radiation from Cobalt-60 source at room temperature. Physical properties of grafted natural rubber such as chloroform number, swelling ratio and gel content weremore » measured. The VAc content of NR-g-PVAc was investigated by titration and visualized by FTIR spectroscopy. The FTIR spectra of NR-g-PVAc prepared at 0-10 kGys showed characteristic peaks of the vinyl acetate confirming that VAc could be grafted onto natural rubber molecular chains effectively under appropriate irradiation conditions. From the result, radiation grafting was found to be a useful technique for grafting of vinyl acetate onto natural rubber.« less

Influence of matching solubility parameter of polymer matrix and CNT on electrical conductivity of CNT/rubber composite

PubMed Central

Ata, Seisuke; Mizuno, Takaaki; Nishizawa, Ayumi; Subramaniam, Chandramouli; Futaba, Don N.; Hata, Kenji

2014-01-01

We report a general approach to fabricate elastomeric composites possessing high electrical conductivity for applications ranging from wireless charging interfaces to stretchable electronics. By using arbitrary nine kinds of rubbers as matrices, we experimentally demonstrate that the matching the solubility parameter of CNTs and the rubber matrix is important to achieve higher electrical conductivity in CNT/rubber composite, resulting in continuous conductive pathways leading to electrical conductivities as high as 15 S/cm with 10 vol% CNT in fluorinated rubber. Further, using thermodynamic considerations, we demonstrate an approach to mix CNTs to arbitrary rubber matrices regardless of solubility parameter of matrices by adding small amounts of fluorinated rubber as a polymeric-compatibilizer of CNTs. We thereby achieved electrical conductivities ranging from 1.2 to 13.8 S/cm (10 vol% CNTs) using nine varieties of rubber matrices differing in chemical structures and physical properties. Finally, we investigated the components of solubility parameter of CNT by using Hansen solubility parameters, these findings may useful for controlling solubility parameter of CNTs. PMID:25434701

Experimental Investigation on Damping Property of Coarse Aggregate Replaced Rubber Concrete

NASA Astrophysics Data System (ADS)

Sugapriya, P.; Ramkrishnan, R.; Keerthana, G.; Saravanamurugan, S.

2018-02-01

Rubber has good damping and vibrational characteristics and can reduce cracking significantly due to its elastic nature. This property of rubber can be incorporated in concrete to control vibrations and create better pavements. Crumb Rubber on being dumped in landfills has serious repercussions and causes soil and land pollution. An innovative use of waste tires is shredding them into small pieces and using them as a replacement for coarse aggregate. Crumb rubber is obtained by chopping scrap tires, and in this study it was added in two different sets named SET 1 - Treated Crumb Rubber and concrete, and SET 2 - Treated Crumb rubber with Ultra Fine GGBS as admixture in concrete. Coarse aggregate replaces Rubber in each of the 2 SET’s in proportions of 5, 10, 15 and 20%. Properties like Compressive Strength, Young’s Modulus, Direct and Semi direct Ultrasonic Pulse Velocity, Sorptivity, Damping ratio and Frequency were found out. Deformation and mode shape were studied with modal analysis and static analysis by applying a uniform pressure corresponding to the highest compressive strength of the slab, using ANSYS.

Modeling and Evaluation of Miles-in-Trail Restrictions in the National Air Space

NASA Technical Reports Server (NTRS)

Grabbe, Shon; Sridhar, Banavar

2003-01-01

Miles-in-trail restrictions impact flights in the national air space on a daily basis and these restrictions routinely propagate between adjacent Air Route Traffic Control Centers. Since overly restrictive or ineffective miles-in-trail restrictions can reduce the overall efficiency of the national air space, decision support capabilities that model miles-in-trail restrictions should prove to be very beneficial. This paper presents both an analytical formulation and a linear programming approach for modeling the effects of miles-in-trail restrictions. A methodology for monitoring the conformance of an existing miles-in-trail restriction is also presented. These capabilities have been implemented in the Future ATM Concepts Evaluation Tool for testing purposes. To allow alternative restrictions to be evaluated in post-operations, a new mode of operation, which is referred to as the hybrid-playback mode, has been implemented in the simulation environment. To demonstrate the capabilities of these new algorithms, the miles-in-trail restrictions, which were in effect on June 27, 2002 in the New York Terminal Radar Approach Control, are examined. Results from the miles-in-trail conformance monitoring functionality are presented for the ELIOT, PARKE and WHITE departure fixes. In addition, the miles-in-trail algorithms are used to assess the impact of alternative restrictions at the PARKE departure fix.

Mechanism of trail following by the arboreal termite Nasutitermes corniger (Isoptera: Termitidae).

PubMed

Gazai, Vinícius; Bailez, Omar; Viana-Bailez, Ana Maria

2014-01-01

In this study, we investigated the mechanisms used by the arboreal termite Nasutitermes corniger (Motschulsky, 1855) to follow trails from the nest to sources of food. A plate containing one of seven trail types was used to connect an artificial nest of N. corniger with an artificial foraging arena. The trail types were: termite trail; paraffined termite trail; trail made of paraffin; rectal fluid extract trail; sternal gland extract trail; feces extract trail; and solvent trail (control). In each test, the time was recorded from the start of the test until the occurrence of trail following, at which point the number of termites that followed the trail for least 5 cm in the first 3 min of observation was recorded. The delay for termites initiating trail following along the termite trail was lower (0.55 ± 0.16 min) than in the trails of sternal gland extract (1.05 ± 0.08 min) and trails of termite feces extract (1.57 ± 0.21 min) (F(2), (48) = 22.59, P < 0.001). The number of termites that followed the termite trail was greater (207.3 ± 17.3) than the number that followed the trail of termite feces extract (102.5 ± 9.4) or sternal gland extract (36, 9 ± 1.6) (F(2), (48) = 174.34, P < 0.001). Therefore, feces on the trail may play an important role alongside sternal gland pheromones in increasing the persistence of the trail.

Laboratory Investigation on the Effects of Natural Fine Aggregates and Recycled Waste Tire Rubber in Pervious Concrete to Develop More Sustainable Pavement Materials

NASA Astrophysics Data System (ADS)

Bonicelli, Alessandra; Fuentes, Luis G.; Khalil Dawd Bermejo, Ibrahim

2017-10-01

Pervious concrete pavement is a recognized sustainable solution for urban roads. To enhance mechanical properties of pervious concrete material, in order to allow wider use of this technology, a lot of studies are going on all over the world. The use of a little percentage of fine aggregates is proven to increase the material resistance without an excessive reduction of permeability. This study aimed to evaluate the effect of replacing the fine virgin aggregates with r cycled tire rubber. 14 different mixes were analysed in terms of indirect tensile strength resistance, void content and density. Two different dimensions of crumb rubber were studied, as well as two different dosages, which were applied to different no-fine control mixes. All results were compared with the same control mixes containing natural fine aggregate. The mixes had a fixed granulometric curve but varied in water/cement ratio; this in order to evaluate the effect of recycled rubber depending to w/c ratio of the mix. An image analysis was also conducted to verify the rubber distribution in the mixture and the cracking surfaces. The experimental analysis showed that a correct proportioning of fine sand significantly increased the strength of the material. Moreover, the use of recycled waste tire rubber, gave interesting improvements respect to the no-fine control mixes, even though the developed resistance was lower respect to mixes containing mineral sand. This result was expected because of the cementing property of mineral sand. Although, the important result was that it was possible to use waste tire rubber in pervious concrete, with an appropriate dosage and granular dimension, for increasing the performance of traditional mix design, in order to achieve pavement materials more and more sustainable.

Expression of osteoprotegerin and its ligands, RANKL and TRAIL, in rheumatoid arthritis

PubMed Central

Remuzgo-Martínez, Sara; Genre, Fernanda; López-Mejías, Raquel; Ubilla, Begoña; Mijares, Verónica; Pina, Trinitario; Corrales, Alfonso; Blanco, Ricardo; Martín, Javier; Llorca, Javier; González-Gay, Miguel A.

2016-01-01

Osteoprotegerin (OPG), receptor activator of nuclear factor-ΚB ligand (RANKL) and tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) have been involved in rheumatoid arthritis (RA) pathophysiology. In this study, we assessed messenger RNA (mRNA) expression of these molecules by qPCR in peripheral blood from 26 patients with RA (12 of them with ischemic heart disease –IHD) and 10 healthy controls. Correlation coefficients between OPG, RANKL and TRAIL expression levels in RA patients and their clinical and demographic characteristics were also evaluated. Whereas OPG and OPG/TRAIL ratio expression were significantly increased in RA patients compared to controls (fold change = 1.79, p = 0.013 and 2.07, p = 0.030, respectively), RANKL/OPG ratio was significantly decreased (fold change = 0.50, p = 0.020). No significant differences were found between patients and controls in RANKL and TRAIL expression. Interestingly, TRAIL expression was significantly higher in RA patients with IHD compared to those without IHD (fold change = 1.46, p = 0.033). Moreover, biologic disease-modifying antirheumatic drugs (DMARDs) significantly decreased RANKL expression in RA patients (p = 0.016). Our study supports an important role of OPG and TRAIL in RA. Furthermore, it highlights an effect of biologic DMARDs in the modulation of RANKL. PMID:27403809

Association of circulating sTRAIL and high-sensitivity CRP with type 2 diabetic nephropathy and foot ulcers

PubMed Central

Arık, Hasan Onur; Yalcin, Arzu Didem; Gumuslu, Saadet; Genç, Gizem Esra; Turan, Adil; Sanlioglu, Ahter Dilsad

2013-01-01

Background Hyperglycemia is among the potent factors that may induce or facilitate apoptosis. TNF-Related Apoptosis-Inducing Factor (TRAIL) is known for its apoptotic and immunomodulatory effects that have recently been correlated with diabetes. We examined serum-soluble TRAIL (sTRAIL) and high-sensitivity CRP (hs-CRP) levels and their association with various distinct parameters in type 2 diabetic nephropathy patients with diabetic foot disease. Material/Methods Twenty-two diabetic nephropathy patients with foot ulcers were enrolled in our study. Patients had been diagnosed with diabetes at age 24±10.58 years. Circulating sTRAIL and Hs-CRP levels were compared with control values, and possible correlations were investigated with parameters such as age, Wagner’s Grade (WG), BMI, HbA1c, and creatinine. Results Serum sTRAIL levels were significantly reduced in the patient group, compared to healthy subjects. High HsCRP levels correlated with age, and WGS correlated with BMI and creatinine levels. Conclusions Significantly suppressed sTRAIL levels in diabetic nephropathy patients with foot ulcers compared to healthy controls suggest a protective role for TRAIL in the disease setting. PMID:23986130

Effect of sterilization on stiffness and dimensional stability of rubber-dam clamps.

PubMed

Giebink, D L; Mathieu, G P; Hondrum, S O

1996-01-01

Simulated clinical conditions were used to test the effect of sterilization on rubber-dam clamp stiffness and dimension. Sixty Hygienic and Ivory W7 clamps were either steam or dry heat sterilized and compared to controls. Stiffness and dimensional change between Ivory clamp groups was significant (p<.0001); the sterilized clamps showed less change than the controls. Hygienic groups showed a significant different between the control and dry heat groups (p<.05); the sterilized clamps showed less change than the controls. The change in stiffness and interjaw width for all Ivory clamps compared to all Hygienic clamps was significant (p<.0001). The Hygienic clamps changes less than the Ivory clamps. The results indicate that steam and dry heat sterilization do not affect retention of rubber-dam clamps.

Channel-wing System for Thrust Deflection and Force/Moment Generation

NASA Technical Reports Server (NTRS)

Englar, Robert J. (Inventor); Bushnell, Dennis M. (Inventor)

2006-01-01

An aircraft comprising a Channel Wing having blown c h - ne1 circulation control wings (CCW) for various functions. The blown channel CCW includes a channel that has a rounded or near-round trailing edge. The channel further has a trailing-edge slot that is adjacent to the rounded trailing edge of the channel. The trailing-edge slot has an inlet connected to a source of pressurized air and is capable of tangentially discharging pressurized air over the rounded trailing edge. The aircraft further has a propeller that is located in the channel and ahead of the rounded trailing edge of the channel. The propeller provides a propeller thrust exhaust stream across the channel wing to propel the aircraft through the air and to provide high lift. The pressurized air being discharged over the rounded trailing edge provides a high lift that is obtained independent of an aircraft angle of attack, thus preventing the asymmetry. separated flow, and stall experienced by the CC wing at the high angle of attack it required for high lift generation. The aircraft can further include blown outboard circulation control wings (CCW) that are synergistically connected to the blown channel CCWs. The blown outboard CCWs provide additional high lift, control thrust/drag interchange, and can provide all three aerodynamic moments when differential blowing is applied front-to-rear or left-to-right. Both the blown channel CCW and the outboard CCW also have leading-edge blowing slots to prevent flow separation or to provide aerodynamic moments for control.

Effect of concentrated epoxidised natural rubber and silica masterbatch for tyre application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Azira, A. A., E-mail: azira@lgm.gov.my; Kamal, M. M., E-mail: mazlina@lgm.gov.my; Verasamy, D., E-mail: devaraj@lgm.gov.my

The availability of concentrated epoxidised natural rubber (ENR-LC) has provided a better opportunity for using epoxidised natural rubber (ENR) with silica to reinforce natural rubber for tyre application. ENR-LC mixed directly with silica to rubber by high speed stirrer without using any coupling agent. Some rubber compounds were prepared by mixing a large amount of precipitated amorphous white silica with natural rubber. The silica was prepared in aqueous dispersion and the filler was perfectly dispersed in the ENR-LC. The performance of the composites was evaluated in this work for the viability of ENR-LC/Si in tyre compounding. Compounding was carried outmore » on a two roll mill, where the additives and curing agents was later mixed. Characterization of these composites was performed by Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) for dispersion as well as mechanical testing. C-ENR/Si showed efficient as primary reinforcing filler in ENR with regard to modulus and tensile strength, resulting on an increase in the stiffness of the rubbers compared to ENR latex. Overall improvement in the mechanical properties for the ENR-LC over the control crosslinked rubber sample was probably due to synergisms of silica reinforcement and crosslinking of the polymeric matrix phase.« less

Effect of concentrated epoxidised natural rubber and silica masterbatch for tyre application

NASA Astrophysics Data System (ADS)

Azira, A. A.; Verasamy, D.; Kamal, M. M.

2016-07-01

The availability of concentrated epoxidised natural rubber (ENR-LC) has provided a better opportunity for using epoxidised natural rubber (ENR) with silica to reinforce natural rubber for tyre application. ENR-LC mixed directly with silica to rubber by high speed stirrer without using any coupling agent. Some rubber compounds were prepared by mixing a large amount of precipitated amorphous white silica with natural rubber. The silica was prepared in aqueous dispersion and the filler was perfectly dispersed in the ENR-LC. The performance of the composites was evaluated in this work for the viability of ENR-LC/Si in tyre compounding. Compounding was carried out on a two roll mill, where the additives and curing agents was later mixed. Characterization of these composites was performed by Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) for dispersion as well as mechanical testing. C-ENR/Si showed efficient as primary reinforcing filler in ENR with regard to modulus and tensile strength, resulting on an increase in the stiffness of the rubbers compared to ENR latex. Overall improvement in the mechanical properties for the ENR-LC over the control crosslinked rubber sample was probably due to synergisms of silica reinforcement and crosslinking of the polymeric matrix phase.

Trail pheromone disruption of red imported fire ant.

PubMed

Suckling, David M; Stringer, Lloyd D; Bunn, Barry; El-Sayed, Ashraf M; Vander Meer, Robert K

2010-07-01

The fire ant, Solenopsis invicta (Hymenoptera: Formicidae), is considered one of the most aggressive and invasive species in the world. Toxic bait systems are used widely for control, but they also affect non-target ant species and cannot be used in sensitive ecosystems such as organic farms and national parks. The fire ant uses recruitment pheromones to organize the retrieval of large food resources back to the colony, with Z,E-alpha-farnesene responsible for the orientation of workers along trails. We prepared Z,E-alpha-farnesene, (91% purity) from extracted E,E-alpha-farnesene and demonstrated disruption of worker trail orientation after presentation of an oversupply of this compound from filter paper point sources (30 microg). Trails were established between queen-right colony cells and food sources in plastic tubs. Trail-following behavior was recorded by overhead webcam, and ants were digitized before and after presentation of the treatment, using two software approaches. The linear regression statistic, r(2) was calculated. Ants initially showed high linear trail integrity (r(2) = 0.75). Within seconds of presentation of the Z,E-alpha-farnesene treatment, the trailing ants showed little or no further evidence of trail following behavior in the vicinity of the pheromone source. These results show that trailing fire ants become disorientated in the presence of large amounts of Z,E-alpha-farnesene. Disrupting fire ant recruitment to resources may have a negative effect on colony size or other effects yet to be determined. This phenomenon was demonstrated recently for the Argentine ant, where trails were disrupted for two weeks by using their formulated trail pheromone, Z-9-hexadecenal. Further research is needed to establish the long term effects and control potential for trail disruption in S. invicta.

Association between thyroid hormones and TRAIL.

PubMed

Bernardi, Stella; Bossi, Fleur; Toffoli, Barbara; Giudici, Fabiola; Bramante, Alessandra; Furlanis, Giulia; Stenner, Elisabetta; Secchiero, Paola; Zauli, Giorgio; Carretta, Renzo; Fabris, Bruno

2017-11-01

Recent studies suggest that a circulating protein called TRAIL (TNF-related apoptosis-inducing ligand) might have a role in the regulation of body weight and metabolism. Interestingly, thyroid hormones seem to increase TRAIL tissue expression. This study aimed at evaluating whether overt thyroid disorders affected circulating TRAIL levels. TRAIL circulating levels were measured in euthyroid, hyperthyroid, and hypothyroid patients before and after thyroid function normalization. Univariate and multivariate analyses were performed to evaluate the correlation between thyroid hormones and TRAIL. Then, the stimulatory effect of both triiodothyronine (T3) and thyroxine (T4) on TRAIL was evaluated in vitro on peripheral blood mononuclear cells. Circulating levels of TRAIL significantly increased in hyperthyroid and decreased in hypothyroid patients as compared to controls. Once thyroid function was restored, TRAIL levels normalized. There was an independent association between TRAIL and both fT3 and fT4. Consistent with these findings, T3 and T4 stimulated TRAIL release in vitro. Here we show that thyroid hormones are associated with TRAIL expression in vivo and stimulate TRAIL expression in vitro. Given the overlap between the metabolic effects of thyroid hormones and TRAIL, this work sheds light on the possibility that TRAIL might be one of the molecules mediating thyroid hormones peripheral effects. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Controllable Change of Photoluminescence Spectra of Silicone Rubber Modified by 193 nm ArF Excimer Laser

NASA Astrophysics Data System (ADS)

Okoshi, Masayuki; Iyono, Minako; Inoue, Narumi

2009-12-01

Photoluminescence spectra of silicone rubber ([SiO(CH3)2]n) photochemically modified by a 193 nm ArF excimer laser was found to be controllable. Compared with the modification in air, the photoluminescence spectra could be blueshifted by the modification in vacuum or the additional irradiation of ArF excimer laser in vacuum after the modification in air. To redshift, on the other hand, the additional irradiation of a 157 nm F2 laser in air after the modification in air, the modification in oxygen gas, or the postannealing after the modification in oxygen gas was effective. The blue and redshifts of the photoluminescence were essentially due to the acceleration of reduction and oxidation reactions of silicone rubber, respectively, because the photoluminescence derives its origin from oxygen deficiency centers and peroxy centers of the silica structure in the modified silicone rubber. On the basis of the spectra changes, colorful light-guiding sheets made of silicone rubber under illumination of a 375 nm light-emitting diode were successfully fabricated for cellular phone use.

Local anaesthetic infiltration for the rubber band ligation of early symptomatic haemorrhoids: a systematic review and meta-analysis.

PubMed

Sajid, M S; Bhatti, M I; Caswell, J; Sains, P; Baig, M K

2015-03-01

The objective of this article is to systematically analyse the randomized, controlled trials evaluating the effectiveness of local anaesthetic infiltration prior to the rubber band ligation of early symptomatic haemorrhoids. Published randomized, controlled trials comparing the use of local anaesthetic (LA) versus no-local anaesthetic (NLA) for the rubber band ligation of early symptomatic haemorrhoids were analysed using RevMan®, and the combined outcomes were expressed as odds ratios (OR) and standardized mean difference (SMD). Four randomized, controlled trials evaluating 387 patients were retrieved from the standard electronic databases. The risk of treatment failure (OR 0.44; 95% CI 0.07, 2.79; z = 0.87; p = 0.39) and post-procedure complications (OR 0.48; 95% CI 0.08, 2.76; z = 0.83; p = 0.41) was similar between two techniques. However, the post-procedure pain score (SMD -5.19; 95% CI -9.08, -1.30; z = 2.62; p < 0.009) was significantly lower in the group of patients undergoing rubber band ligation of haemorrhoids under local anaesthetic injection. The use of LA appears to have clinically measurable advantages over NLA in the rubber band ligation of early symptomatic haemorrhoids to lessen post-procedure pain.

Morpho-Molecular Characterization of Two Ampelomyces spp. (Pleosporales) Strains Mycoparasites of Powdery Mildew of Hevea brasiliensis.

PubMed

Liyanage, Kapila K; Khan, Sehroon; Brooks, Siraprapa; Mortimer, Peter E; Karunarathna, Samantha C; Xu, Jianchu; Hyde, Kevin D

2018-01-01

Powdery mildew disease of rubber affects immature green leaves, buds, inflorescences, and other immature tissues of rubber trees, resulting in up to 45% losses in rubber latex yield worldwide. The disease is often controlled by dusting the diseased plants with powdered sulfur, which can have long-term negative effects on the environment. Therefore, it is necessary to search for alternative and environmentally friendly control methods for this disease. This study aimed to identify mycoparasites associated with rubber powdery mildew species, and characterize them on the basis of morpho-molecular characteristics and phylogenetic analyses of ITS rDNA regions. We observed that the Ampelomyces fungus parasitizes rubber powdery mildew, and eventually destroys it. Furthermore, on the basis of phylogenetic analyses and morphological characteristics we confirmed that the Ampelomyces mycoparasite isolated from rubber powdery mildew is closely related to other mycohost taxa in the Erysiphe genus. A total of 73 (71 retrieved from GenBank and two obtained from fresh collections of rubber powdery mildew fungi) Ampelomyces spp. were analyzed using ITS rDNA sequences and 153 polymorphic sites were identified through haplotypic analyses. A total of 28 haplotypes (H1-H28) were identified to have a complex network of mutation events. The results from phylogenetic tree constructed on the basis of maximum likelihood analyses, and the haplotype network tree revealed similar relationships of clustering pattern. This work presents the first report on morpho-molecular characterization of Ampelomyces species that are mycoparasites of powdery mildew of Hevea brasiliensis .

Photo-excitable hybrid nanocomposites for image-guided photo/TRAIL synergistic cancer therapy.

PubMed

Lin, Gan; Zhang, Yang; Zhu, Congqing; Chu, Chengchao; Shi, Yesi; Pang, Xin; Ren, En; Wu, Yayun; Mi, Peng; Xia, Haiping; Chen, Xiaoyuan; Liu, Gang

2018-05-22

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) can induce apoptosis in cancer cells without toxicity to normal cells. However, the efficiency is greatly limited by its short half-life and wild resistance in various cancer cells. In this study, we reported a micellar hybrid nanoparticle to carry TRAIL ligand (denoted as IPN@TRAIL) for a novel photo-excited TRAIL therapy. These IPN@TRAIL offered increased TRAIL stability, prolonged half-life and enhanced tumor accumulation, monitored by dual mode imaging. Furthermore, IPN@TRAIL nanocomposites enhanced wrapped TRAIL therapeutic efficiency greatly towards resistant cancer cells by TRAIL nanovectorization. More importantly, when upon external laser, these nanocomposites not only triggered tumor photothermal therapy (PTT), but also upregulated the expression of death receptors (DR4 and DR5), resulting in a greater apoptosis mediated by co-delivered TRAIL ligand. Such photo/TRAIL synergistic effect showed its great killing effects in a controllable manner on TRAIL-resistant A549 tumor model bearing mice. Finally, these nanocomposites exhibited rapid clearance without obvious systemic toxicity. All these features rendered our nanocomposites a promising theranostic platform in cancer therapy. Copyright © 2018 Elsevier Ltd. All rights reserved.

Preparation of sulfonic acid-containing rubbers from natural rubber vulcanizates

NASA Astrophysics Data System (ADS)

Poonsawat, Worapong; Poompradub, Sirilux; Ngamcharussrivichai, Chawalit

2014-06-01

In this work, a series of sulfonic acid-containing rubbers were prepared by aqueous phase oxidation of natural rubber vulcanizates in the presence of hydrogen peroxide (H2O2) and formic acid (HCOOH). The starting vulcanizates were neatly prepared via an efficient vulcanization (EV) system by varying mass ratio of N-cyclohexyl-2-benzothiazole sulfonamide (CBS), as an accelerator, to sulfur. The oxidation conditions were controlled at the molar ratio of H2O2: HCOOH = 1:1, the concentration of H2O2 = 15 wt.%, the temperature = 50 °C, and the reaction time = 3 h. The rubber materials before and after the oxidation were characterized for their physicochemical properties by using Fourier transform infrared spectroscopy, bomb calorimetry, acid-base titration and swelling measurements. The results indicated the presence of sulfonic acid group in the oxidized rubbers, generated by the oxidative cleaves of sulfide crosslinks in the rubber vulcanizates. The oxidation decreased the sulfur content of the rubber in which the level of sulfur loss was determined by the CBS/sulfur ratio. Moreover, the acidity of the oxidized products was correlated with the amount of sulfur remaining.

Environmental perceptions and objective walking trail audits inform a community-based participatory research walking intervention

PubMed Central

2012-01-01

Background Given the documented physical activity disparities that exist among low-income minority communities and the increased focused on socio-ecological approaches to address physical inactivity, efforts aimed at understanding the built environment to support physical activity are needed. This community-based participatory research (CBPR) project investigates walking trails perceptions in a high minority southern community and objectively examines walking trails. The primary aim is to explore if perceived and objective audit variables predict meeting recommendations for walking and physical activity, MET/minutes/week of physical activity, and frequency of trail use. Methods A proportional sampling plan was used to survey community residents in this cross-sectional study. Previously validated instruments were pilot tested and appropriately adapted and included the short version of the validated International Physical Activity Questionnaire, trail use, and perceptions of walking trails. Walking trails were assessed using the valid and reliable Path Environmental Audit Tool which assesses four content areas including: design features, amenities, maintenance, and pedestrian safety from traffic. Analyses included Chi-square, one-way ANOVA's, multiple linear regression, and multiple logistic models. Results Numerous (n = 21) high quality walking trails were available. Across trails, there were very few indicators of incivilities and safety features rated relatively high. Among the 372 respondents, trail use significantly predicted meeting recommendations for walking and physical activity, and MET/minutes/week. While controlling for other variables, significant predictors of trail use included proximity to trails, as well as perceptions of walking trail safety, trail amenities, and neighborhood pedestrian safety. Furthermore, while controlling for education, gender, and income; for every one time per week increase in using walking trails, the odds for meeting walking recommendations increased 1.27 times, and the odds for meeting PA recommendation increased 3.54 times. Perceived and objective audit variables did not predict meeting physical activity recommendations. Conclusions To improve physical activity levels, intervention efforts are needed to maximize the use of existing trails, as well as improve residents' perceptions related to incivilities, safety, conditions of trail, and amenities of the walking trails. This study provides important insights for informing development of the CBPR walking intervention and informing local recreational and environmental policies in this southern community. PMID:22289653

Sister-chromatid exchanges and cell-cycle kinetics in the lymphocytes of workers occupationally exposed to a chemical mixture in the tyre industry.

PubMed

Sasiadek, M

1993-08-01

Cytogenetic studies of clinically healthy workers employed in the rubber industry showed an increase in chromosome aberrations (CAs), sister-chromatid exchanges (SCEs) and a decrease in proliferation indices (PIs). The aim of the present study was to establish, using the SCE and PI tests, genotoxic effects of hazardous chemicals in the rubber industry. An increase in mean SCEs in the lymphocytes of vulcanizers as compared to controls was observed. Since the PI in the exposed group was insignificantly decreased as compared to the controls, it could be concluded that the SCE test is the most sensitive cytogenetic test for the detection of a genotoxic effect of chemicals in the rubber industry. There was no evidence in the present study that the genotoxic effect of chemicals in the rubber industry was enhanced by cigarette smoking.

Responses of rubber leaf phenology to climatic variations in Southwest China

NASA Astrophysics Data System (ADS)

Zhai, De-Li; Yu, Haiying; Chen, Si-Chong; Ranjitkar, Sailesh; Xu, Jianchu

2017-11-01

The phenology of rubber trees (Hevea brasiliensis) could be influenced by meteorological factors and exhibits significant changes under different geoclimates. In the sub-optimal environment in Xishuangbanna, rubber trees undergo lengthy periods of defoliation and refoliation. The timing of refoliation from budburst to leaf aging could be affected by powdery mildew disease (Oidium heveae), which negatively impacts seed and latex production. Rubber trees are most susceptible to powdery mildew disease at the copper and leaf changing stages. Understanding and predicting leaf phenology of rubber trees are helpful to develop effective means of controlling the disease. This research investigated the effect of several meteorological factors on different leaf phenological stages in a sub-optimal environment for rubber cultivation in Jinghong, Yunnan in Southwest China. Partial least square regression was used to quantify the relationship between meteorological factors and recorded rubber phenologies from 2003 to 2011. Minimum temperature in December was found to be the critical factor for the leaf phenology development of rubber trees. Comparing the delayed effects of minimum temperature, the maximum temperature, diurnal temperature range, and sunshine hours were found to advancing leaf phenologies. A comparatively lower minimum temperature in December would facilitate the advancing of leaf phenologies of rubber trees. Higher levels of precipitation in February delayed the light green and the entire process of leaf aging. Delayed leaf phenology was found to be related to severe rubber powdery mildew disease. These results were used to build predictive models that could be applied to early warning systems of rubber powdery mildew disease.

Up regulation of serum tumor necrosis factor-related apoptosis inducing ligand in juvenile-onset systemic lupus erythematosus: relations with disease activity, antibodies to double -stranded DNA, nephritis and neutropenia.

PubMed

Ezzat, Mohamed H M; El-Gammasy, Tarek M A; Shaheen, Kareem Y A; El-Mezdawi, Ramzi A M; Youssef, Mervat S M

2013-06-01

Apoptosis is induced by binding of death receptor ligands, members of the tumor necrosis factor (TNF) superfamily, to their cognate receptors. It is suggested that TNF-related apoptosis inducing ligand (TRAIL) is involved in pathogenesis of juvenile-onset systemic lupus erythematosus (JSLE). This study aimed to assess TRAIL concentrations in sera of JSLE children and to determine their potential relationship with disease activity, anti-double-stranded DNA (anti-dsDNA) levels, neutropenia and renal involvement. Circulating levels of TRAIL were measured by enzyme-linked immunosorbent assay (ELISA) in serum samples obtained from 40 JSLE patients (20 with active and 20 with inactive disease) and 20 controls. The mean (SEM) serum TRAIL concentration in JSLE was 1750.7 (440.2) pg/mL. Serum TRAIL concentrations in patients were higher than those in controls (P < 0.01). Serum TRAIL concentrations for children with inactive disease (1854.8 [485.4] pg/mL) and those with activity (1646.6 [390.6] pg/mL) were statistically comparable. JSLE children with positive anti-dsDNA antibodies had significantly higher TRAIL levels (mean = 1846 [456] vs. 1455 [325] pg/mL; P < 0.05). Serum TRAIL concentrations were significantly higher in classes III and IV nephritis compared to classes I and II nephritis (1970 [512] vs. 1330 [331] pg/mL; P < 0.01). Serum TRAIL concentrations in patients with neutropenia were higher than those without neutropenia (1805 [505] vs. 1516 [400] pg/mL; P = 0.042) and in controls (P = 0.024). Our data indicate that an increased level of TRAIL is a feature of JSLE that correlates with disease activity, anti-dsDNA titers neutropenia and lupus nephritis. © 2013 The Authors International Journal of Rheumatic Diseases © 2013 Asia Pacific League of Associations for Rheumatology and Wiley Publishing Asia Pty Ltd.

Managing visitor impacts in parks: A multi-method study of the effectiveness of alternative management practices

USGS Publications Warehouse

Park, L.O.; Marion, J.L.; Manning, R.E.; Lawson, S.R.; Jacobi, C.

2008-01-01

How can recreation use be managed to control associated environmental impacts? What management practices are most effective and why? This study explored these and related questions through a series of experimental ?treatments? and associated ?controls? at the summit of Cadillac Mountain in Acadia National Park, a heavily used and environmentally fragile area. The treatments included five management practices designed to keep visitors on maintained trails, and these practices ranged from ?indirect? (information/education) to ?direct? (a fence bordering the trail). Research methods included unobtrusive observation of visitors to determine the percentage of visitors who walked off-trail and a follow-up visitor survey to explore why management practices did or didn?t work. All of the management practices reduced the percentage of visitors who walked off-trail. More aggressive applications of indirect practices were more effective than less aggressive applications, and the direct management practice of fencing was the most effective of all. None of the indirect management practices reduced walking off-trail to a degree that is likely to control damage to soil and vegetation at the study site. Study findings suggest that an integrated suite of direct and indirect management practices be implemented on Cadillac Mountain (and other, similar sites) that includes a) a regulation requiring visitors to stay on the maintained trail, b) enforcement of this regulation as needed, c) unobtrusive fencing along the margins of the trail, d) redesign of the trail to extend it, widen it in key places, and provide short spur trails to key ?photo points?, and e) an aggressive information/education program to inform visitors of the regulation to stay on the trail and the reasons for it. These recommendations are a manifestation of what may be an emerging principle of park and outdoor recreation management: intensive use requires intensive management.

Numerical study of the trailing vortex of a wing with wing-tip blowing

NASA Technical Reports Server (NTRS)

Lim, Hock-Bin

1994-01-01

Trailing vortices generated by lifting surfaces such as helicopter rotor blades, ship propellers, fixed wings, and canard control surfaces are known to be the source of noise, vibration, cavitation, degradation of performance, and other hazardous problems. Controlling these vortices is, therefore, of practical interest. The formation and behavior of the trailing vortices are studied in the present research. In addition, wing-tip blowing concepts employing axial blowing and spanwise blowing are studied to determine their effectiveness in controlling these vortices and their effects on the performance of the wing. The 3D, unsteady, thin-layer compressible Navier-Stokes equations are solved using a time-accurate, implicit, finite difference scheme that employs LU-ADI factorization. The wing-tip blowing is simulated using the actuator plane concept, thereby, not requiring resolution of the jet slot geometry. Furthermore, the solution blanking feature of the chimera scheme is used to simplify the parametric study procedure for the wing-tip blowing. Computed results are shown to compare favorably with experimental measurements. It is found that axial wing-tip blowing, although delaying the rolling-up of the trailing vortices and the near-field behavior of the flowfield, does not dissipate the circulation strength of the trailing vortex farther downstream. Spanwise wing-tip blowing has the effect of displacing the trailing vortices outboard and upward. The increased 'wing-span' due to the spanwise wing-tip blowing has the effect of lift augmentation on the wing and the strengthening of the trailing vortices. Secondary trailing vortices are created at high spanwise wing-tip blowing intensities.

Evaluation of asphalt rubber stress-absorbing membrane.

DOT National Transportation Integrated Search

1997-01-01

This report describes the construction and evaluation of a stress-absorbing membrane (SAM) using a liquid asphalt binder containing ground tire rubber. Approximately 10 lane-km of SAM and 4 lane-km of control surface treatment for comparison were con...

The Motor and the Brake of the Trailing Leg in Human Walking: Leg Force Control Through Ankle Modulation and Knee Covariance

PubMed Central

Toney, Megan E.; Chang, Young-Hui

2016-01-01

Human walking is a complex task, and we lack a complete understanding of how the neuromuscular system organizes its numerous muscles and joints to achieve consistent and efficient walking mechanics. Focused control of select influential task-level variables may simplify the higher-level control of steady state walking and reduce demand on the neuromuscular system. As trailing leg power generation and force application can affect the mechanical efficiency of step-to-step transitions, we investigated how joint torques are organized to control leg force and leg power during human walking. We tested whether timing of trailing leg force control corresponded with timing of peak leg power generation. We also applied a modified uncontrolled manifold analysis to test whether individual or coordinated joint torque strategies most contributed to leg force control. We found that leg force magnitude was adjusted from step-to-step to maintain consistent leg power generation. Leg force modulation was primarily determined by adjustments in the timing of peak ankle plantar-flexion torque, while knee torque was simultaneously covaried to dampen the effect of ankle torque on leg force. We propose a coordinated joint torque control strategy in which the trailing leg ankle acts as a motor to drive leg power production while trailing leg knee torque acts as a brake to refine leg power production. PMID:27334888

The association of trail use with weather-related factors on an urban greenway.

PubMed

Burchfield, Ryan A; Fitzhugh, Eugene C; Bassett, David R

2012-02-01

To study the association between weather-related measures and objectively measured trail use across 3 seasons. Weather has been reported as a barrier to outdoor physical activity (PA), but previous studies have explained only a small amount of the variance in PA using weather-related measures. The dependent variable of this study was trail use measured as mean hourly trail counts by an infrared trail counter located on a greenway. Each trail count represents 1 person breaking the infrared beam of the trail counter. Two sources of weather-related measures were obtained by a site-specific weather station and a public domain weather source. Temperature, relative humidity, and precipitation were significantly correlated with trail counts recorded during daylight hours. More precise hourly weather-related measures explained 42% of the variance in trail counts, regardless of the weather data source with temperature alone explaining 18% of the variance in trail counts. After controlling for all seasonal and weekly factors, every 1°F increase in temperature was associated with an increase of 1.1 trail counts/hr up to 76°F, at which point trail use began to slightly decrease. Weather-related factors have a moderate association with trail use along an urban greenway.

Pheromone trailing behavior of the brown tree snake, Boiga irregularis.

PubMed

Greene, M J; Stark, S L; Mason, R T

2001-11-01

The ability of snakes to follow pheromone trails has significant consequences for survival and reproduction. Of particular importance is the ability of snakes to locate conspecifics during the breeding season via the detection of pheromone trails. In this study, the ability of male brown tree snakes (Boiga irregularis), a tropical, rear-fanged colubrid, to follow pheromone trails produced by reproductively active conspecifics was tested in the laboratory by using a Y maze. Males displayed a trailing response to both female and male pheromone trails over blank controls. As males of this species display ritualized combat behavior, these responses likely represent both direct and indirect mechanisms, respectively, for the location of potential mates in the wild. Males did not, however, discriminate between male and female trails when given a choice on the Y maze.

Effectiveness and costs of overland skid trail BMPs

Treesearch

Clay Sawyers; W. Michael Aust; M. Chad Bolding; William A. Lakel III

2012-01-01

Forestry Best Management Practices (BMPs) are designed to protect water quality; however, little data exists comparing the efficacy and costs of different BMP options for skid trail closure. Study objectives were to evaluate erosion control effectiveness and implementation costs of five overland skid trail closure techniques. Closure techniques were: waterbar only (...

Comparative efficacy of multimodal digital methods in assessing trail/resource degradation

Treesearch

Logan O. Park

2014-01-01

Outdoor recreation can cause both positive and negative impacts on associated forest ecosystems. Forest recreation trails localize negative impacts to a controlled spatial extent while providing recreation access beyond developed areas and transportation networks. Current methods for assessing extent and severity of trail and proximal resource degradation require...

Morpho-Molecular Characterization of Two Ampelomyces spp. (Pleosporales) Strains Mycoparasites of Powdery Mildew of Hevea brasiliensis

PubMed Central

Liyanage, Kapila K.; Khan, Sehroon; Brooks, Siraprapa; Mortimer, Peter E.; Karunarathna, Samantha C.; Xu, Jianchu; Hyde, Kevin D.

2018-01-01

Powdery mildew disease of rubber affects immature green leaves, buds, inflorescences, and other immature tissues of rubber trees, resulting in up to 45% losses in rubber latex yield worldwide. The disease is often controlled by dusting the diseased plants with powdered sulfur, which can have long-term negative effects on the environment. Therefore, it is necessary to search for alternative and environmentally friendly control methods for this disease. This study aimed to identify mycoparasites associated with rubber powdery mildew species, and characterize them on the basis of morpho-molecular characteristics and phylogenetic analyses of ITS rDNA regions. We observed that the Ampelomyces fungus parasitizes rubber powdery mildew, and eventually destroys it. Furthermore, on the basis of phylogenetic analyses and morphological characteristics we confirmed that the Ampelomyces mycoparasite isolated from rubber powdery mildew is closely related to other mycohost taxa in the Erysiphe genus. A total of 73 (71 retrieved from GenBank and two obtained from fresh collections of rubber powdery mildew fungi) Ampelomyces spp. were analyzed using ITS rDNA sequences and 153 polymorphic sites were identified through haplotypic analyses. A total of 28 haplotypes (H1–H28) were identified to have a complex network of mutation events. The results from phylogenetic tree constructed on the basis of maximum likelihood analyses, and the haplotype network tree revealed similar relationships of clustering pattern. This work presents the first report on morpho-molecular characterization of Ampelomyces species that are mycoparasites of powdery mildew of Hevea brasiliensis. PMID:29403464

Experimental and Numerical Characterization of Polymer Nanocomposites for Solid Rocket Motor Internal Insulation

DTIC Science & Technology

2006-09-30

Nanophase, Thermoplastic Elastomer, EPDM Rubber , Surface Modified MMT Clay, Carbon Nanofibers 16. SECURITY CLASSIFICATION OF: a. REPORT u b. ABSTRACT U...diene rubber ( EPDM ) is the baseline insulation material for solid rocket motor cases. A novel class of insulation materials was developed by the Air...Figure 1. Upon analysis of the control sample, it was observed that the EPDM rubber was totally burned forming a small amount of char, which was easily

Utilization of waste tire rubber in manufacture of oriented strandboard.

PubMed

Ayrilmis, Nadir; Buyuksari, Umit; Avci, Erkan

2009-09-01

Some physical and mechanical properties of oriented strandboards (OSBs) containing waste tire rubber at various addition levels based on the oven-dry strand weight, using the same method as that used in the manufacture of OSB. Two resin types, phenol-formaldehyde (PF) and polyisocyanate, were used in the experiments. The manufacturing parameters were: a specific gravity of 0.65 and waste tire rubber content (10/90, 20/80 and 30/70 by wt.% of waste tire rubber/wood strand). Average internal bond values of PF-bonded OSB panels with rubber chips were between 17.6% and 48.5% lower than the average of the control samples while polyisocyanate bonded OSBs were 16.5-50.6%. However, water resistance and mechanical properties of OSBs made using polyisocyanate resin were found to comply with general-purpose OSB minimum property requirements of EN 300 Type 1 (1997) values for use in dry conditions at the lowest tire rubber loading level (10%) based on the oven-dry panel weight. The tire rubber improved water resistance of the OSB panel due to its almost hydrophobic property. Based on the findings obtained from this study, we concluded that waste tire rubber could be used for general-purpose OSB manufacturing up to 10% ratio based on the oven-dry panel weight.

Use of waste tires (crumb rubber) on Colorado highways.

DOT National Transportation Integrated Search

2014-12-01

The objective of this study was to determine the feasibility of using waste tires (crumb rubber) in the : construction of asphalt pavements in Colorado. Two pilot test sections and one control section were constructed : and observed over a five-year ...

Evapotranspiration of rubber ( Hevea brasiliensis ) cultivated at two plantation sites in Southeast Asia: RUBBER EVAPOTRANSPIRATION IN SE ASIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giambelluca, Thomas W.; Mudd, Ryan G.; Liu, Wen

The expansion of rubber (Hevea brasiliensis) cultivation to higher latitudes and higher elevations in southeast Asia is part of a dramatic shift in the direction of rural land cover change in the region toward more tree covered landscapes. To investigate the possible effects of increasing rubber cultivation in the region on ecosystem services including water cycling, eddy covariance towers were established to measure ecosystem fluxes within two rubber plantations, one each in Bueng Kan, northeastern Thailand, and Kampong Cham, central Cambodia. The results show that evapotranspiration (ET) at both sites is strongly related to variations in available energy and leafmore » area, and moderately controlled by soil moisture. Measured mean annual ET was 1128 and 1272 mm for the Thailand and Cambodia sites, respectively. After adjustment for energy closure, mean annual was estimated to be 1211 and 1459 mm yr at the Thailand and Cambodia sites, respectively. Based on these estimates and that of another site in Xishuangbanna, southwestern China, it appears that of rubber is higher than that of other tree dominated land covers in the region, including forest. While measurements by others in non rubber tropical ecosystems indicate that at high net radiation sites is at most only slightly higher than for sites with lower net radiation, mean annual rubber increases strongl with increasing net radiation across the three available rubber plantation observation sites. With the continued expansion of tree dominated land covers, including rubber cultivation, in southeast Asia, the possible association between commercially viable, fast growing tree crop species Giambelluca et al. Evapotranspiration of rubber (Havea brasiliensis) cultivated at two sites in southeast Asia and their relatively high water use raises concerns about potential effects on water and food security.« less

Comparative Analysis of Latex Transcriptome Reveals Putative Molecular Mechanisms Underlying Super Productivity of Hevea brasiliensis

PubMed Central

Li, Heping; Fan, Yujie; Yang, Jianghua; Qi, Jiyan; Li, Huibo

2013-01-01

Increasing demand for natural rubber prompts studies into the mechanisms governing the productivity of rubber tree ( Hevea brasiliensis ). It is very interesting to notice that a rubber tree of clone PR107 in Yunnan, China is reported to yield more than 20 times higher than the average rubber tree. This super-high-yielding (SHY) rubber tree (designated as SY107), produced 4.12 kg of latex (cytoplasm of rubber producing laticifers, containing about 30% of rubber) per tapping, more than 7-fold higher than that of the control. This rubber tree is therefore a good material to study how the rubber production is regulated at a molecular aspect. A comprehensive cDNA-AFLP transcript profiling was performed on the latex of SY107 and its average counterparts by using the 384 selective primer pairs for two restriction enzyme combinations (ApoI/MseI and TaqI/MseI). A total of 746 differentially expressed (DE) transcript-derived fragments (TDFs) were identified, of which the expression patterns of 453 TDFs were further confirmed by RT-PCR. These RT-PCR confirmed TDFs represented 352 non-redundant genes, of which 215 had known or partially known functions and were grouped into 10 functional categories. The top three largest categories were transcription and protein synthesis (representing 24.7% of the total genes), defense and stress (15.3%), and primary and secondary metabolism (14.0%). Detailed analysis of the DE-genes suggests notable characteristics of SHY phenotype in improved sucrose loading capability, rubber biosynthesis-preferred sugar utilization, enhanced general metabolism and timely stress alleviation. However, the SHY phenotype has little correlation with rubber-biosynthesis pathway genes. PMID:24066172

A Lettuce (Lactuca sativa) Homolog of Human Nogo-B Receptor Interacts with cis-Prenyltransferase and Is Necessary for Natural Rubber Biosynthesis*

PubMed Central

Qu, Yang; Chakrabarty, Romit; Tran, Hue T.; Kwon, Eun-Joo G.; Kwon, Moonhyuk; Nguyen, Trinh-Don; Ro, Dae-Kyun

2015-01-01

Natural rubber (cis-1,4-polyisoprene) is an indispensable biopolymer used to manufacture diverse consumer products. Although a major source of natural rubber is the rubber tree (Hevea brasiliensis), lettuce (Lactuca sativa) is also known to synthesize natural rubber. Here, we report that an unusual cis-prenyltransferase-like 2 (CPTL2) that lacks the conserved motifs of conventional cis-prenyltransferase is required for natural rubber biosynthesis in lettuce. CPTL2, identified from the lettuce rubber particle proteome, displays homology to a human NogoB receptor and is predominantly expressed in latex. Multiple transgenic lettuces expressing CPTL2-RNAi constructs showed that a decrease of CPTL2 transcripts (3–15% CPTL2 expression relative to controls) coincided with the reduction of natural rubber as low as 5%. We also identified a conventional cis-prenyltransferase 3 (CPT3), exclusively expressed in latex. In subcellular localization studies using fluorescent proteins, cytosolic CPT3 was relocalized to endoplasmic reticulum by co-occurrence of CPTL2 in tobacco and yeast at the log phase. Furthermore, yeast two-hybrid data showed that CPTL2 and CPT3 interact. Yeast microsomes containing CPTL2/CPT3 showed enhanced synthesis of short cis-polyisoprenes, but natural rubber could not be synthesized in vitro. Intriguingly, a homologous pair CPTL1/CPT1, which displays ubiquitous expressions in lettuce, showed a potent dolichol biosynthetic activity in vitro. Taken together, our data suggest that CPTL2 is a scaffolding protein that tethers CPT3 on endoplasmic reticulum and is necessary for natural rubber biosynthesis in planta, but yeast-expressed CPTL2 and CPT3 alone could not synthesize high molecular weight natural rubber in vitro. PMID:25477521

A lettuce (Lactuca sativa) homolog of human Nogo-B receptor interacts with cis-prenyltransferase and is necessary for natural rubber biosynthesis.

PubMed

Qu, Yang; Chakrabarty, Romit; Tran, Hue T; Kwon, Eun-Joo G; Kwon, Moonhyuk; Nguyen, Trinh-Don; Ro, Dae-Kyun

2015-01-23

Natural rubber (cis-1,4-polyisoprene) is an indispensable biopolymer used to manufacture diverse consumer products. Although a major source of natural rubber is the rubber tree (Hevea brasiliensis), lettuce (Lactuca sativa) is also known to synthesize natural rubber. Here, we report that an unusual cis-prenyltransferase-like 2 (CPTL2) that lacks the conserved motifs of conventional cis-prenyltransferase is required for natural rubber biosynthesis in lettuce. CPTL2, identified from the lettuce rubber particle proteome, displays homology to a human NogoB receptor and is predominantly expressed in latex. Multiple transgenic lettuces expressing CPTL2-RNAi constructs showed that a decrease of CPTL2 transcripts (3-15% CPTL2 expression relative to controls) coincided with the reduction of natural rubber as low as 5%. We also identified a conventional cis-prenyltransferase 3 (CPT3), exclusively expressed in latex. In subcellular localization studies using fluorescent proteins, cytosolic CPT3 was relocalized to endoplasmic reticulum by co-occurrence of CPTL2 in tobacco and yeast at the log phase. Furthermore, yeast two-hybrid data showed that CPTL2 and CPT3 interact. Yeast microsomes containing CPTL2/CPT3 showed enhanced synthesis of short cis-polyisoprenes, but natural rubber could not be synthesized in vitro. Intriguingly, a homologous pair CPTL1/CPT1, which displays ubiquitous expressions in lettuce, showed a potent dolichol biosynthetic activity in vitro. Taken together, our data suggest that CPTL2 is a scaffolding protein that tethers CPT3 on endoplasmic reticulum and is necessary for natural rubber biosynthesis in planta, but yeast-expressed CPTL2 and CPT3 alone could not synthesize high molecular weight natural rubber in vitro. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

The rubber plantation environment and Lassa fever epidemics in Liberia, 2008-2012: a spatial regression.

PubMed

Olugasa, Babasola O; Dogba, John B; Ogunro, Bamidele; Odigie, Eugene A; Nykoi, Jomah; Ojo, Johnson F; Taiwo, Olalekan; Kamara, Abraham; Mulbah, Charles K; Fasunla, Ayotunde J

2014-10-01

As Lassa fever continues to be a public health challenge in West Africa, it is critical to produce good maps of its risk pattern for use in active surveillance and control intervention. We identified eight spatial features related to the rubber plantation environment and used them as explanatory variables for Lassa fever (LF) outbreaks on the Uniroyal Liberian Agricultural Company (LAC) rubber plantation environment in Grand Bassa County, Liberia. We computed classical and spatial lag regression models on all spatial features, including proximity of residential camp to rubber tree-edge, main road in the plantation, LAC hospital, rice farmland, household refuse dump, human population density, post-harvest storage density of rice and density of rodent deterrent on rice storage. We found significant (p=0.0024) spatial autocorrelation between LF cases and the spatial features we have considered. We concluded that the rubber plantation environment influenced Mastomys species' breeding and transmission of Lassa virus along spatial scale to humans. The risk factors identified in this study offered a baseline for more effective surveillance and control of LF in the post-civil conflict Liberia. Copyright © 2014 Elsevier Ltd. All rights reserved.

Aerodynamic analysis of seamless horizontal stabilizer

NASA Astrophysics Data System (ADS)

Nithya, S.; Kanimozhi, S.

2017-05-01

This project presents an investigative view into the concept of seamless aeroelastic wing and hingeless flexible trailing edge. Wings are designed to provide maximum lift and minimal drag and weight. But with conventional wings where rivets are used and the control surfaces are separately hinged, parasite drag comes into play. This project is about analysing a smooth seamless wing with hinge-less flexible trailing edge. This type of wing reduces the drag considerably and the hinge-less trailing edge leads to a minimal control demand and reduces the noise produced when the aircraft comes for landing. Seamless aeroelastic wing will function as an integrated one piece lifting and control surface. It has been designed to enhance a desirable wing camber for control by deflecting a hinge-less flexible trailing edge part instead of a traditional hinged control surface. This kind of flexible wing can be achieved either by a curved beam and disc actuation mechanism or by piezo-electric materials, whose shape change can be achieved by electricity. The intent of this project is to analyze the effects of introducing the concept of Seamless Wing to the horizontal stabilizer. While the removal of rivets and serrations that hinge the elevators to the stabilizer reduces the overall drag by a reasonable value, the overall concept of a control surface-less stabilizer where the maneuvers are done by deflecting the trailing edge offers better maneuverability.

Negative feedback in ants: crowding results in less trail pheromone deposition

PubMed Central

Czaczkes, Tomer J.; Grüter, Christoph; Ratnieks, Francis L. W.

2013-01-01

Crowding in human transport networks reduces efficiency. Efficiency can be increased by appropriate control mechanisms, which are often imposed externally. Ant colonies also have distribution networks to feeding sites outside the nest and can experience crowding. However, ants do not have external controllers or leaders. Here, we report a self-organized negative feedback mechanism, based on local information, which downregulates the production of recruitment signals in crowded parts of a network by Lasius niger ants. We controlled crowding by manipulating trail width and the number of ants on a trail, and observed a 5.6-fold reduction in the number of ants depositing trail pheromone from least to most crowded conditions. We also simulated crowding by placing glass beads covered in nest-mate cuticular hydrocarbons on the trail. After 10 bead encounters over 20 cm, forager ants were 45 per cent less likely to deposit pheromone. The mechanism of negative feedback reported here is unusual in that it acts by downregulating the production of a positive feedback signal, rather than by direct inhibition or the production of an inhibitory signal. PMID:23365196

Comparison of trailside degradation across a gradient of trail use in the Sonoran Desert.

PubMed

Rowe, Helen Ivy; Tluczek, Melanie; Broatch, Jennifer; Gruber, Dan; Jones, Steve; Langenfeld, Debbie; McNamara, Peggy; Weinstein, Leona

2018-02-01

As recreational visitation to the Sonoran Desert increases, the concern of scientists, managers and advocates who manage its natural resources deepens. Although many studies have been conducted on trampling of undisturbed vegetation and the effects of trails on adjacent plant and soil communities, little such research has been conducted in the arid southwest. We sampled nine 450-m trail segments with different visitation levels in Scottsdale's McDowell Sonoran Preserve over three years to understand the effects of visitation on soil erosion, trailside soil crusts and plant communities. Soil crust was reduced by 27-34% near medium and high use trails (an estimated peak rate of 13-70 visitors per hour) compared with control plots, but there was less than 1% reduction near low use trails (peak rate of two to four visitors per hour). We did not detect soil erosion in the center 80% of the trampled area of any of the trails. The number of perennial plant species dropped by less than one plant species on average, but perennial plant cover decreased by 7.5% in trailside plots compared with control plots 6 m off-trail. At the current levels of visitation, the primary management focus should be keeping people on the originally constructed trail tread surface to reduce impact to adjacent soil crusts. Copyright © 2017 Elsevier Ltd. All rights reserved.

Correlation between preferentially expressed antigen of melanoma and tumour necrosis factor-related apoptosis-inducing ligand gene expression in different types of leukaemia patients.

PubMed

Zhang, Wenhui; Chi, Kaikai; Zhang, Yin; Ma, Baogen; Shi, Jie; Chen, Yuqing; Lei, Pingchong; Li, Yulong; Sun, Kai

2013-01-01

Tumour necrosis factor-related apoptosis-inducing ligand (TRAIL) down-regulation by preferentially expressed antigen of melanoma (PRAME) is a general phenomenon in different types of solid tumours, but research on the correlation between PRAME and TRAIL gene expression in leukaemia patients is rare. PRAME and TRAIL expression was detected in bone marrow samples from 80 newly diagnosed acute leukaemia (AL) patients and 40 chronic myeloid leukaemia (CML) patients using TaqMan-based real-time quantitative PCR methods, and a linear correlation analysis was performed on their levels of expression. A total of 15 normal bone marrow samples from individuals with non-malignant haematological diseases served as normal controls. PRAME expression was higher in both AL and CML patients compared to controls (both p < 0.001). CML patients in both blast crisis (BC) and the accelerated phase (AP) had significantly higher PRAME levels than CML patients in the chronic phase (CP) (p = 0.006 and 0.0461, respectively). TRAIL expression was higher in both the acute myeloid leukaemia (AML) group and the acute lymphoblastic leukaemia (ALL) group than in the controls (p = 0.039 and 0.047, respectively). In contrast, CML patients had lower TRAIL levels than controls (p = 0.043), and TRAIL expression in CML patients in the advanced phases (BC and AP) was significantly lower than in CML-CP patients (p = 0.006). In CML patients, there was a significant inverse correlation (Spearman's R = -0.6669, p < 0.0001) between PRAME and TRAIL gene expression, while a greater significant inverse correlation was found in patients in the advanced phases (BC and AP) (R = -0.6764). In addition, no correlation was observed in AML and ALL patients. The simultaneous detection of PRAME and TRAIL gene expression may be helpful to monitor condition changes in leukaemia patients and evaluate therapeutic effects in clinical practice, particularly in CML patients. © 2013 S. Karger AG, Basel.

Use Deflected Trailing Edge to Improve the Aerodynamic Performance and Develop Low Solidity LPT Cascade

NASA Astrophysics Data System (ADS)

Chao, Li; Peigang, Yan; Xiangfeng, Wang; Wanjin, Han; Qingchao, Wang

2017-08-01

This paper investigates the feasibility of improving the aerodynamic performance of low pressure turbine (LPT) blade cascades and developing low solidity LPT blade cascades through deflected trailing edge. A deflected trailing edge improved aerodynamic performance of both LPT blade cascades and low solidity LPT blade cascades. For standard solidity LPT cascades, deflecting the trailing edge can decrease the energy loss coefficient by 20.61 % for a Reynolds number (Re) of 25,000 and freestream turbulence intensities (FSTI) of 1 %. For a low solidity LPT cascade, aerodynamic performance was also improved by deflecting the trailing edge. Solidity of the LPT cascade can be reduced by 12.5 % for blades with a deflected trailing edge without a drop in efficiency. Here, the flow control mechanism surrounding a deflected trailing edge was also revealed.

76 FR 54730 - Rubicon Trail Easement, Eldorado National Forest, Pacific Ranger District

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... erosion control feature as described in the Rubicon Trail Saturated Soil Water Quality Protection Plan (El..., OHV users also drive the trail when it is covered by snow and at times when saturated soil conditions... the Saturated Soil Water Quality Protection Plan would be constructed from Little Sluice to the County...

Assessing children's cognitive flexibility with the Shape Trail Test.

PubMed

Chan, Amy Y C; Morgan, Sarah-Jane

2018-01-01

In this paper we report an initial validation of the Shape Trail Test-Child Version (STT-CV) with a non-clinical sample of children aged 6 to 9 years. The STT-CV has been developed as an age-appropriate and culturally fair direct downward extension of the Trail Making Test (TMT) for the assessment of cognitive flexibility. Children completed the STT-CV and four established measures of executive functions that assessed working memory, inhibitory control and task switching. Results showed the expected age-based differences in completion times for both parts of the STT-CV (Trail A and Trail B). Children's performance on the STT-CV correlated significantly with all four measures of executive functions. After controlling for the effects of chronological age, completion times for Trail B remained correlated with most other measures of executive functions. These findings provide emerging evidence for the utility of the STT-CV, and highlight the need for designing and using appropriate variants of the TMT in the behavioural assessment of cognitive flexibility in developmentally and culturally diverse populations.

Characterization of recycled rubber media for hydrogen sulphide (H2S) control.

PubMed

Wang, Ning; Park, Jaeyoung; Evans, Eric A; Ellis, Timothy G

2014-01-01

Hydrogen sulphide (H2S) adsorption capacities on recycled rubber media, tyre-derived rubber particle (TDRP), and other rubber material (ORM) have been evaluated. As part of the research, densities, moisture contents, and surface properties of TDRP and ORM have been determined. The research team findings show that TDRP and ORM are more particulate in nature and not highly porous-like activated carbon. The characteristics of surface area, pore size, and moisture content support chemisorption on the macrosurface rather than physical adsorption in micropores. For example, moisture content is essential for H2S adsorption on ORM, and an increase in moisture content results in an increase in adsorption capacity.

Demonstration/Validation of the TC-60 Controlled Detonation Chamber, Porton Down, UK: Final Demonstration Test Report

DTIC Science & Technology

2007-06-01

Joint At the exit of the expansion tank, a polymeric composition of ethylene-propylene- diene terpolymer ( EPDM ) rubber was used to mate the flange of...The final connection of the detonator was cumbersome for an operator wearing thick butyl rubber gloves. The detonator wire connection was made to a...operators were required to wear PPE, including rubber gloves. The decision was made to transfer the PLC components to outside the VCS. In Phase I, the

Recreational trails as corridors for alien plants in the Rocky Mountains, USA

USGS Publications Warehouse

Wells, Floye H.; Lauenroth, William K.; Bradford, John B.

2012-01-01

Alien plant species often use areas of heavy human activity for habitat and dispersal. Roads and utility corridors have been shown to harbor more alien species than the surrounding vegetation and are therefore believed to contribute to alien plant persistence and spread. Recreational trails represent another corridor that could harbor alien species and aid their spread. Effective management of invasive species requires understanding how alien plants are distributed at trailheads and trails and how their dispersal may be influenced by native vegetation. Our overall goal was to investigate the distribution of alien plants at trailheads and trails in the Rocky Mountains of Colorado. At trailheads, we found that although the number of alien species was less than the number of native species, alien plant cover ( x̄=50%) did not differ from native plant cover, and we observed a large number of alien seedlings in the soil seed bank, suggesting that alien plants are a large component of trailhead communities and will continue to be so in the future. Along trails, we found higher alien species richness and cover on trail (as opposed to 4 m from the trail) in 3 out of 4 vegetation types, and we observed higher alien richness and cover in meadows than in other vegetation types. Plant communities at both trailheads and trails, as well as seed banks at trailheads, contain substantial diversity and abundance of alien plants. These results suggest that recreational trails in the Rocky Mountains of Colorado may function as corridors that facilitate the spread of alien species into wildlands. Our results suggest that control of alien plants should begin at trailheads where there are large numbers of aliens and that control efforts on trails should be prioritized by vegetation type.

New understanding of microstructure formation of the rubber phase in thermoplastic vulcanizates (TPV).

PubMed

Wu, Hanguang; Tian, Ming; Zhang, Liqun; Tian, Hongchi; Wu, Youping; Ning, Nanying

2014-03-21

The breakup of the rubber phase in an ethylene-propylene-diene monomer (EPDM)/polypropylene (PP) blend at the early stage of dynamic vulcanization is similar to that in an unvulcanized EPDM/PP blend because of the low crosslink density of the EPDM phase. In this work, the minimum size of the rubber phase in the unvulcanized EPDM/PP blend was first calculated by using the critical breakup law of viscoelastic droplets in a matrix. The calculated results showed that the minimum size of the rubber phase in the unvulcanized blend was in the nanometer scale (25-46 nm), not the micrometer scale as reported in many works. Meanwhile, the actual size of the rubber phase in the thermoplastic vulcanizate (TPV) at both the early stage and the final stage of dynamic vulcanization was observed by using peak force tapping atomic force microscopy (PF-AFM). The results indicated that the EPDM phase indeed broke up into nanoparticles at the early stage of dynamic vulcanization, in good agreement with the calculated results. More interestingly, we first revealed that the micrometer-sized rubber particles commonly observed in TPV were actually the agglomerates of rubber nanoparticles with diameters between 40 and 60 nm. The mechanism for the formation of rubber nanoparticles and their agglomerates during dynamic vulcanization was then discussed. Our work provides guidance to control the microstructure of the rubber phase in TPV to prepare high performance TPV products for a wide range of applications in the automobile and electronic industries.

Active Control of Separation From the Flap of a Supercritical Airfoil

NASA Technical Reports Server (NTRS)

Melton, La Tunia Pack; Yao, Chung-Sheng; Seifert, Avi

2003-01-01

Active flow control in the form of periodic zero-mass-flux excitation was applied at several regions on the leading edge and trailing edge flaps of a simplified high-lift system t o delay flow separation. The NASA Energy Efficient Transport (EET) supercritical airfoil was equipped with a 15% chord simply hinged leading edge flap and a 25% chord simply hinged trailing edge flap. Detailed flow features were measured in an attempt to identify optimal actuator placement. The measurements included steady and unsteady model and tunnel wall pressures, wake surveys, arrays of surface hot-films, flow visualization, and particle image velocimetry (PIV). The current paper describes the application of active separation control at several locations on the deflected trailing edge flap. High frequency (F(+) approx.= 10) and low frequency amplitude modulation (F(+)AM approx.= 1) of the high frequency excitation were used for control. Preliminary efforts to combine leading and trailing edge flap excitations are also reported.

Vortex developments over steady and accelerated airfoils incorporating a trailing edge jet

NASA Technical Reports Server (NTRS)

Finaish, F.; Okong'o, N.; Frigerio, J.

1993-01-01

Computational and experimental studies are conducted to investigate the influence of a trailing edge jet on flow separation and subsequent vortex formation over steady and accelerated airfoils at high angles of attack. A computer code, employing the stream function-vorticity approach, is developed and utilized to conduct numerical experiments on the flow problem. To verify and economize such efforts, an experimental system is developed and incorporated into a subsonic wind tunnel where streamline and vortex flow visualization experiments are conducted. The study demonstrates the role of the trailing edge jet in controlling flow separation and subsequent vortex development for steady and accelerating flow at angles past the static stall angle of attack. The results suggest that the concept of the trailing edge jet may be utilized to control the characteristics of unsteady separated flows over lifting surfaces. This control possibility seems to be quite effective and could have a significant role in controlling unsteady separated flows.

Comparison of vegetation conditions along two backcountry trails in Mount Robson Provincial Park, British Columbia (Canada).

PubMed

Nepal, Sanjay K; Way, Paul

2007-01-01

Vegetation conditions, i.e., plant cover, species richness, and the presence of exotic species, are compared along a high-use trail (Berg Lake Trail--BLT) and a low use trail (Mt. Fitzwilliam Trail--FWT) in Canada's Mt. Robson Provincial Park. We established 71 paired quadrats (1 m x 1 m), and assessed the amount of vegetation cover and species richness by four main lifeforms, i.e., woody species, herbaceous species, ferns, and moss, lichen and fungi. The following hypotheses were tested: (1) differences exist between control and trailside quadrats in vegetation cover, species richness and floristic diversity, and (2) differences exist between the high and low-use trails in the above-mentioned three parameters. Results show that for the majority of variables the differences between the control and trailside quadrats are statistically not significant. Variables showing significant differences are relative vegetation cover (for BLT only), exposed soil (BLT and FWT), herbaceous cover (FWT), moss, lichen and fungi cover (BLT), overall species richness (BLT), and herbaceous species richness (BLT). Ruderal and exotic species are present but only on trailside quadrats of the high-use trail. Results indicate that the Park administration's strategy to disperse use in the Mt. Robson Provincial Park should be examined critically, and some guidelines for acceptability of changes should be developed.

Dyslipidemia and Diabetes Increase the OPG/TRAIL Ratio in the Cardiovascular System.

PubMed

Toffoli, Barbara; Fabris, Bruno; Bartelloni, Giacomo; Bossi, Fleur; Bernardi, Stella

2016-01-01

Background . Dyslipidemia and diabetes are two of the most well established risk factors for the development of cardiovascular disease (CVD). Both of them usually activate a complex range of pathogenic pathways leading to organ damage. Here we hypothesized that dyslipidemia and diabetes could affect osteoprotegerin (OPG) and TNF-related apoptosis-inducing ligand (TRAIL) expression in the vessels and the heart. Materials and Methods . Gene and protein expression of OPG, TRAIL, and OPG/TRAIL ratio were quantified in the aorta and the hearts of control mice, dyslipidemic mice, and diabetic mice. Results . Diabetes significantly increased OPG and the OPG/TRAIL ratio expression in the aorta, while dyslipidemia was the major determinant of the changes observed in the heart, where it significantly increased OPG and reduced TRAIL expression, thus increasing cardiac OPG/TRAIL ratio. Conclusions . This work shows that both dyslipidemia and diabetes affect OPG/TRAIL ratio in the cardiovascular system. This could contribute to the changes in circulating OPG/TRAIL which are observed in patients with diabetes and CVD. Most importantly, these changes could mediate/contribute to atherosclerosis development and cardiac remodeling.

Amphiphilic semi-interpenetrating polymer networks using pulverized rubber

NASA Astrophysics Data System (ADS)

Shahidi, Nima

Scrap rubber materials provide a significant challenge to either reuse or safe disposal. Every year, millions of tires are discarded to landfills in the United States, consuming a staggering amount of land space, creating a high risk for large fires, breeding mosquitoes that spread diseases, and wasting the planet's natural resources. This situation cannot be sustained. The challenge of reusing scrap rubber materials is mainly due to the crosslinked structure of vulcanized rubber that prevent them from melting and further processing for reuse. The most feasible recycling approach is believed to be a process in which the vulcanized rubber is first pulverized into a fine powder and then incorporated into new products. The production of fine rubber particles is generally accomplished through the use of a cryogenic process that is costly. Therefore, development of a cost effective technology that utilizes a large quantity of the scrap rubber materials to produce high value added materials is an essential element in maintaining a sustainable solution to rubber recycling. In this research, a cost effective pulverization process, solid state shear extrusion (SSSE), was modified and used for continuous pulverization of the rubber into fine particles. In the modified SSSE process, pulverization takes place at high compressive shear forces and a controlled temperature. Furthermore, an innovative particle modification process was developed to enhance the chemical structure and surface properties of the rubber particles for manufacturing of high value added products. Modification of rubber particles was accomplished through the polymerization of a hydrophilic monomer mixture within the intermolecular structure of the hydrophobic rubber particles. The resulting composite particles are considered as amphiphilic particulate phase semi-interpenetrating polymer networks (PPSIPNs). The modified rubber particles are water dispersible and suitable for use in a variety of aqueous media applications such as additives to waterborne emulsions. This innovative process for the first time opened up the application of rubber particles in aqueous media. The kinetics of polymerization reaction of hydrophilic monomer mixture within the rubber particles was investigated based on the assumption of partitioning of acrylic acid monomer in the hydrophobic rubber particles. The produced PPSIPNs were used as additives to waterborne emulsions and the mechanical and physical properties of the prepared coatings were examined. It was observed that the PPSIPNs could be added in high quantities with an improvement in adhesion, enhancement of the impact strength, and hardness of the coatings. This approach aims to develop environmentally benign products from scrap rubber materials.

TRAIL-CM4 fusion protein shows in vitro antibacterial activity and a stronger antitumor activity than solo TRAIL protein.

PubMed

Sang, Ming; Zhang, Jiaxin; Li, Bin; Chen, Yuqing

2016-06-01

A TRAIL-CM4 fusion protein in soluble form with tumor selective apoptosis and antibacterial functions was expressed in the Escherichia coli expression system and isolated through dialysis refolding and histidine-tag Nickel-affinity purification. Fresh Jurkat cells were treated with the TRAIL-CM4 fusion protein. Trypan blue staining and MTT analyses showed that, similar to a TRAIL positive control, Jurkat cell proliferation was significantly inhibited. Flow cytometry analyses using Annexin V-fluorescein revealed that Jurkat cells treated with the TRAIL-CM4 fusion protein exhibited increased apoptosis. Laser confocal microscopy showed that APB-CM4 and the fusion protein TRAIL-CM4 can bind to Jurkat cell membranes and initiate their destruction. ABP-CM4 enhances the antitumor activity of TRAIL by targeting and damaging the tumor cell membrane. In antibacterial experiments, agar well diffusion and bacterial growth inhibition curve assays revealed concentration-dependent TRAIL-CM4 antibacterial activity against Escherichia coli K12D31. The expressed TRAIL-CM4 fusion protein exhibited enhanced antitumor and antibacterial activities. Fusion protein expression allowed the two different proteins to function in combination. Copyright © 2016 Elsevier Inc. All rights reserved.

Zinc Leaching from Tire Crumb Rubber

NASA Astrophysics Data System (ADS)

Rhodes, E. P.; Ren, J.; Mays, D. C.

2010-12-01

Recent estimates indicate that more than 2 billion scrap tires are currently stockpiled in the United States and approximately 280 million more tires are added annually. Various engineering applications utilize recycled tires in the form of shredded tire crumb rubber. However, the use of tire crumb rubber may have negative environmental impacts, especially when the rubber comes into contact with water. A review of the literature indicates that leaching of zinc from tire crumb rubber is the most significant water quality concern associated with using this material. Zinc is generally used in tire manufacturing, representing approximately 1.3% of the final product by mass. This study will report results from the U.S. Environmental Protection Agency’s (EPA’s) Synthetic Precipitation Leaching Procedure, batch leaching tests, and column leaching tests performed to quantify the process by which zinc leaches from tire crumb rubber into water. Results are interpreted with a first-order kinetic attachment/detachment model, implemented with the U.S. Agricultural Research Service software HYDRUS-1D, in order to determine the circumstances when zinc leaching from tire crumb rubber would be expected to comply with the applicable discharge limits. One potential application for recycled tires is replacing sand with tire crumb rubber in granular media filters used for stormwater pollution control. For this to be a viable application, the total zinc in the stormwater discharge must be below the EPA’s benchmark value of 0.117 mg/L.

Laticifer-specific cis-prenyltransferase silencing affects the rubber, triterpene, and inulin content of Taraxacum brevicorniculatum.

PubMed

Post, Janina; van Deenen, Nicole; Fricke, Julia; Kowalski, Natalie; Wurbs, David; Schaller, Hubert; Eisenreich, Wolfgang; Huber, Claudia; Twyman, Richard M; Prüfer, Dirk; Gronover, Christian Schulze

2012-03-01

Certain Taraxacum species, such as Taraxacum koksaghyz and Taraxacum brevicorniculatum, produce large amounts of high-quality natural rubber in their latex, the milky cytoplasm of specialized cells known as laticifers. This high-molecular mass biopolymer consists mainly of poly(cis-1,4-isoprene) and is deposited in rubber particles by particle-bound enzymes that carry out the stereospecific condensation of isopentenyl diphosphate units. The polymer configuration suggests that the chain-elongating enzyme (rubber transferase; EC 2.5.1.20) is a cis-prenyltransferase (CPT). Here, we present a comprehensive analysis of transgenic T. brevicorniculatum plants in which the expression of three recently isolated CPTs known to be associated with rubber particles (TbCPT1 to -3) was heavily depleted by laticifer-specific RNA interference (RNAi). Analysis of the CPT-RNAi plants by nuclear magnetic resonance, size-exclusion chromatography, and gas chromatography-mass spectrometry indicated a significant reduction in rubber biosynthesis and a corresponding 50% increase in the levels of triterpenes and the main storage carbohydrate, inulin. Transmission electron microscopy revealed that the laticifers in CPT-RNAi plants contained fewer and smaller rubber particles than wild-type laticifers. We also observed lower activity of hydroxymethylglutaryl-coenzyme A reductase, the key enzyme in the mevalonate pathway, reflecting homeostatic control of the isopentenyl diphosphate pool. To our knowledge, this is the first in planta demonstration of latex-specific CPT activity in rubber biosynthesis.

Impacts of informal trails on vegetation and soils in the highest protected area in the Southern Hemisphere.

PubMed

Barros, Agustina; Gonnet, Jorge; Pickering, Catherine

2013-09-30

There is limited recreation ecology research in South America, especially studies looking at informal trails. Impacts of informal trails formed by hikers and pack animals on vegetation and soils were assessed for the highest protected area in the Southern Hemisphere, Aconcagua Provincial Park. The number of braided trails, their width and depth were surveyed at 30 sites along the main access route to Mt Aconcagua (6962 m a.s.l.). Species composition, richness and cover were also measured on control and trail transects. A total of 3.3 ha of alpine meadows and 13.4 ha of alpine steppe were disturbed by trails. Trails through meadows resulted in greater soil loss, more exposed soil and rock and less vegetation than trails through steppe vegetation. Trampling also affected the composition of meadow and steppe vegetation with declines in sedges, herbs, grasses and shrubs on trails. These results highlight how visitor use can result in substantial cumulative damage to areas of high conservation value in the Andes. With unregulated use of trails and increasing visitation, park agencies need to limit the further spread of informal trails and improve the conservation of plant communities in Aconcagua Provincial Park and other popular parks in the region. Copyright © 2013 Elsevier Ltd. All rights reserved.

Trail impacts in Sagarmatha (Mt. Everest) National Park, Nepal: a logistic regression analysis.

PubMed

Nepal, S K

2003-09-01

A trail study was conducted in the Sagarmatha (Mt. Everest) National Park, Nepal, during 1997-1998. Based on that study, this paper examines the spatial variability of trail conditions and analyzes factors that influence trail conditions. Logistic regression (multinomial logit model) is applied to examine the influence of use and environmental factors on trail conditions. The assessment of trail conditions is based on a four-class rating system: (class I, very little damaged; class II, moderately damaged, class III, heavily damaged; and class IV, severely damaged). Wald statistics and a model classification table have been used for data interpretation. Results indicate that altitude, trail gradient, hazard potential, and vegetation type are positively associated with trail condition. Trails are more degraded at higher altitude, on steep gradients, in areas with natural hazard potential, and within shrub/grassland zones. Strong correlations between high levels of trail degradation and higher frequencies of visitors and lodges were found. A detailed analysis of environmental and use factors could provide valuable information to park managers in their decisions about trail design, layout and maintenance, and efficient and effective visitor management strategies. Comparable studies on high alpine environments are needed to predict precisely the effects of topographic and climatic extremes. More refined approaches and experimental methods are necessary to control the effects of environmental factors.

The reproductive performance of the Mupli beetle, Luprops tristis , in relation to leaf age of the para rubber tree, Hevea brasiliensis

PubMed Central

Sabu, T. K.; Nirdev, P. M.; Aswathi, P.

2014-01-01

Abstract An analysis of host plant leaf age preferences and phenology studies led to the predictions that tender rubber plant leaves are essential for the completion of the life cycle of the Mupli beetle, Luprops tristis Fabricius (Coleoptera: Tenebrionidae) and that low tender leaf availability during the post-dormancy stage will limit the beetle population. Analyses of the effects of feeding the beetles leaves of various ages, nitrogen (N) content, and moisture content on fecundity and the duration of post-dormancy survival were carried out. The results showed that tender leaf availability during the post-dormancy phase of L. tristis is a critical factor that determines the survival of L. tristis adults and the subsequent generation. The control of powdery mildew ( Odium hevea ) disease-mediated premature leaf fall in rubber plantations may regulate the beetle population. A peak in fecundity during the early phase of post-dormancy is proposed as an adaptive mechanism of L. tristis to synchronize egg production and feeding with tender leaf availability in rubber plantations. Variations in nutrient levels and moisture content between deciduous rubber tree leaves of different ages are attributed to the leaf nutrient resorption mechanism of senescing leaves. These results established that tender leaves with high N and moisture levels are essential for post-dormancy survival and that N influences fecundity. The results of the experiments could aid decision making regarding the population management and control of L. tristis in rubber plantations. PMID:25373159

The detection and quantification of the defects in adhesive bonded joints of the piezoelectric sensors by infrared thermographic nondestructive testing

NASA Astrophysics Data System (ADS)

Vinod, P. N.; Joseph, Sherin; John, Reji

2017-04-01

In this paper, efficacy of pulsed thermography technique has been explored for the first time for the detection and quantification of the subsurface defects present in the rubber-encapsulated piezoelectric sensors. Initial experiments were performed on adhesively bonded joints of the rubber/Al or rubber/PZT control samples to find out an optimum acquisition time for the 3-mm rubber encapsulants. Thermographic measurements were performed in the reflection mode and acquired thermal images were analysed and processed images were described in terms of the phase images. The defective regions are identified as delamination of the adhesive joints at the interface of rubber and PZT stacks, and presence of porosity in the encapsulation in the inspected hydrophone. The defect depths of the observed anomalies were calculated empirically from the plots of the peak time of thermal contrast (tmax) maximum and thermal contrast maximum (Cmax) for a particular defect. The estimated defect depths of the prominent porosity observed in the PZT hydrophone are found nearly 1 mm from the surface.

Dairy cow preferences for soft or hard flooring when standing or walking.

PubMed

Telezhenko, E; Lidfors, L; Bergsten, C

2007-08-01

Concrete is the most commonly used alley flooring in confined dairy herds because of its qualities of construction and ease of cleaning. Nevertheless, the hardness, abrasiveness, and slipperiness of concrete floors have adverse effects on animal well-being and health, and yielding rubber flooring is becoming popular as a way of improving the flooring conditions on walkways. The aim of this study was to investigate preferences of dairy cows for rubber compared with concrete flooring under the conditions of a commercial dairy farm. The study was conducted in an organic dairy herd with free-stall housing. Floor preference was tested on groups of standing cows in a 120-m2 holding pen before milking, and 1 yr later on a 12- x 3-m walkway. The holding pen and the walkway were divided lengthwise into 2 identical sections. Two types of solid rubber mats (soft and extra soft) were tested against solid concrete in the holding pen. Slatted and solid rubber mats were tested against slatted concrete in the walkway. Each floor type was tested over 4 d on the left side and 4 d on the right side of the holding pen and the walkway, respectively. Concrete flooring on both sides of the sections was tested as a control before the testing of different section materials. All observations of the distribution of cows in the sections were made from video recordings captured in association with the afternoon milking. The number of cows on each section was recorded approximately every 7 min in the holding pen, and continuously on the walkway. A significantly higher proportion of cows stood on the side with the soft and extra soft rubber mats (65.1 +/- 2.7 and 69.3 +/- 2.6%, respectively, mean +/- SEM) compared with the control distribution when only the solid concrete was available (50.9 +/- 3.9%). A significantly higher proportion of nonlame cows walked exclusively on the side with the slatted (64.5 +/- 5.4%, d 4) or solid rubber mats (68.2 +/- 5.1%, d 4) compared with controls (28.9 +/- 4.3%). Lame cows within a group of walking cows did not show a higher preference for soft flooring as distinct as nonlame cows (52.7 +/- 6.9 and 59.4 +/- 6.2% for the solid and slatted rubber mats, respectively, at d 4 vs. 40.3 +/- 6.2% for control), presumably because of competition with other, higher ranked cows. It was concluded that the majority of cows preferred to walk and stand on soft rubber rather than on concrete flooring.

Acute and chronic pain in calves after different methods of rubber-ring castration.

PubMed

Becker, Johanna; Doherr, Marcus G; Bruckmaier, Rupert M; Bodmer, Michèle; Zanolari, Patrik; Steiner, Adrian

2012-12-01

The goal of the present study was to evaluate the effect of different methods of rubber-ring castration on acute and chronic pain in calves. Sixty-three 4-6 week-old calves were randomly and sequentially allocated to one of five groups: Group RR (traditional rubber ring castration); group BRR (combination of one rubber ring with Burdizzo); group Rcut (one rubber ring applied with the scrotal tissue and rubber ring removed on day 9); group 3RR (three rubber rings placed one above the other around the scrotal neck); and group CO (controls; sham-castrated). All calves received 0.2 mL/kg bodyweight lidocaine 2%, injected into the spermatic cords and around the scrotal neck 15 min before castration. The presence of acute and chronic pain was assessed using plasma cortisol concentrations, response to palpation of scrotal area, time from castration until complete wound healing, and behavioural signs. Calves of group 3RR showed severe swelling and inflammation, and licking of the scrotal area occurred significantly more often than in groups Rcut and CO. Technique 3RR was discontinued for welfare reasons before the end of the study. All castration groups had significantly more pain upon palpation than calves of group CO, but palpation elicited markedly less pain in group Rcut than in the other castration groups. The most rapid healing time and shortest duration of chronic pain after castration was achieved in group Rcut. For welfare reasons, the Rcut technique should be considered as a valuable alternative to traditional rubber ring castration of calves at 4-6 weeks of age. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparative Proteomics of Rubber Latex Revealed Multiple Protein Species of REF/SRPP Family Respond Diversely to Ethylene Stimulation among Different Rubber Tree Clones.

PubMed

Tong, Zheng; Wang, Dan; Sun, Yong; Yang, Qian; Meng, Xueru; Wang, Limin; Feng, Weiqiang; Li, Ling; Wurtele, Eve Syrkin; Wang, Xuchu

2017-05-02

Rubber elongation factor (REF) and small rubber particle protein (SRPP) are two key factors for natural rubber biosynthesis. To further understand the roles of these proteins in rubber formation, six different genes for latex abundant REF or SRPP proteins, including REF 138,175,258 and SRPP 117,204,243 , were characterized from Hevea brasiliensis Reyan (RY) 7-33-97. Sequence analysis showed that REFs have a variable and long N-terminal, whereas SRPPs have a variable and long C-terminal beyond the REF domain, and REF 258 has a β subunit of ATPase in its N-terminal. Through two-dimensional electrophoresis (2-DE), each REF/SRPP protein was separated into multiple protein spots on 2-DE gels, indicating they have multiple protein species. The abundance of REF/SRPP proteins was compared between ethylene and control treatments or among rubber tree clones with different levels of latex productivity by analyzing 2-DE gels. The total abundance of each REF/SRPP protein decreased or changed a little upon ethylene stimulation, whereas the abundance of multiple protein species of the same REF/SRPP changed diversely. Among the three rubber tree clones, the abundance of the protein species also differed significantly. Especially, two protein species of REF 175 or REF 258 were ethylene-responsive only in the high latex productivity clone RY 8-79 instead of in RY 7-33-97 and PR 107. Some individual protein species were positively related to ethylene stimulation and latex productivity. These results suggested that the specific protein species could be more important than others for rubber production and post-translational modifications might play important roles in rubber biosynthesis.

Recreational trails reduce the density of ground-dwelling birds in protected areas.

PubMed

Thompson, Bill

2015-05-01

Recreational disturbance associated with trails has been identified as one of the major factors causing a decline of native biodiversity within protected areas. However, despite the negative impacts that recreation can have on biodiversity, providing public access to nature is critical for the future of the conservation of biodiversity. As such, many protected area managers are looking for tools to help maintain a balance between public access and biodiversity conservation. The objectives of this study were to examine the impacts of recreational trails on forest-dwelling bird communities in eastern North America, identify functional guilds which are particularly sensitive to recreational trails, and derive guidelines for trail design to assist in managing the impacts of recreational trails on forest-dwelling birds. Trails within 24 publicly owned natural areas were mapped, and breeding bird communities were described with the use of point count surveys. The density of forest birds, particularly of those species which nest or forage on the ground, were significantly positively influenced by the amount of trail-free refuge habitat. Although management options to control trail use in non-staffed protected areas are limited, this study suggests that protected area managers could design and maintain a trail network that would minimize impacts on resident wildlife, while providing recreational opportunities for visitors, by designing their trail network to maximize the area of trail-free habitat.

Recreational Trails Reduce the Density of Ground-Dwelling Birds in Protected Areas

NASA Astrophysics Data System (ADS)

Thompson, Bill

2015-05-01

Recreational disturbance associated with trails has been identified as one of the major factors causing a decline of native biodiversity within protected areas. However, despite the negative impacts that recreation can have on biodiversity, providing public access to nature is critical for the future of the conservation of biodiversity. As such, many protected area managers are looking for tools to help maintain a balance between public access and biodiversity conservation. The objectives of this study were to examine the impacts of recreational trails on forest-dwelling bird communities in eastern North America, identify functional guilds which are particularly sensitive to recreational trails, and derive guidelines for trail design to assist in managing the impacts of recreational trails on forest-dwelling birds. Trails within 24 publicly owned natural areas were mapped, and breeding bird communities were described with the use of point count surveys. The density of forest birds, particularly of those species which nest or forage on the ground, were significantly positively influenced by the amount of trail-free refuge habitat. Although management options to control trail use in non-staffed protected areas are limited, this study suggests that protected area managers could design and maintain a trail network that would minimize impacts on resident wildlife, while providing recreational opportunities for visitors, by designing their trail network to maximize the area of trail-free habitat.

Magnetic iron oxide nanoparticles mediated gene therapy for breast cancer--an in vitro study.

PubMed

Wei, Weizhong; Xu, Chunfang; Wu, Hua

2006-01-01

The aim of this study was to evaluate the feasibility and efficacy of using TRAIL gene to treat breast cancer mediated with a novel carrier - magnetic iron oxide nanoparticles (poly-MAG-1000) coated with PEI. The magnetic iron oxide nanoparticles were used as gene carrier to transfect TRAIL gene into MCF-7 cells. The polyMAG-1000 without TRAIL gene was transfected into the tumor cells as negative control. TRAIL gene transfection with liposome as carrier served as positive control. The apoptosis of cells was detected with TUNEL method. The apoptosis ratio of tumor cells was measured with flow cytometry (FCM). It was found that the apoptosis occurred in the tumor cells after transfection of TRAIL gene mediated by both polyMAG-1000 and liposome. The apoptosis ratio in the group with polyMAG-1000 as gene carrier was (25.11+/-2.85) %, whereas it was (5.06+/- 1.05) % in the control group with polyMAG-1000 (P<0.01). The apoptosis ratio was as low as (18.31+/-2.44) % in the group with liposome as gene carrier (P<0.05, as compared with the group with polyMAG-1000 as gene carrier). It is suggested that TRAIL gene may induce apoptosis in MCF-7 breast cancer cells. The magnetic iron oxide nanoparticles coated with PEI may be a potential gene carrier with high transfection efficacy for cancer gene therapy..

Investigation of dairy cattle ease of movement on new methyl methacrylate resin aggregate floorings.

PubMed

Franco-Gendron, N; Bergeron, R; Curilla, W; Conte, S; DeVries, T; Vasseur, E

2016-10-01

Freestall dairy farms commonly present issues with cattle slips and falls caused by smooth flooring and manure slurry. This study examined the effect of 4 new methyl methacrylate (MMA) resin aggregate flooring types (1-4) compared with rubber (positive) and concrete (negative control) on dairy cow (n=18) ease of movement when walking on straight and right-angled corridors. Our hypothesis was that cow ease of movement when walking on the MMA surfaces would be better than when walking on traction milled concrete, and at least as good as when walking on rubber. Cattle ease of movement was measured using kinematics, accelerometers, and visual observation of gait and associated behaviors. Stride length, swing time, stance time, and hoof height were obtained from kinematic evaluation. Acceleration and asymmetry of variance were measured with accelerometers. Locomotion score and behaviors associated with lameness, such as arch back, head bob, tracking up, step asymmetry, and reluctance to bear weight were visually observed. Stride length, swing time, stance time, and the number of steps taken were the only variables affected by flooring type. Differences between flooring types for these variables were tested using a generalized linear mixed model with cow as a random effect, week as a random block factor, and flooring type as a fixed effect. Multiple comparisons with a Scheffé adjustment were done to analyze differences among flooring types. Stride length was 0.14 m longer (better) on rubber when compared with concrete, and 0.11 and 0.17 m shorter on MMA 1 and 2 compared with rubber. On MMA 3 and 4, stride length did not differ from either rubber or concrete. Swing time was 0.04 s shorter (worse) on MMA 1 than on rubber, but did not differ from any other flooring. Stance time was 0.18 s longer (worse) on MMA 2 when compared with rubber, but it did not differ from any other treatment. The number of steps was higher on MMA 4 compared with rubber (4.57 vs. 3.95 steps), but did not differ from any other treatment. Of all the MMA floors tested, MMA 3 was the only one that was consistently as good as rubber (positive control). All 4 MMA floors never differed from concrete (negative control) in any of the ease of movement variables measured. These results suggest that MMA 3 may improve cow ease of movement, compared with the other MMA floors, but more research is required to confirm these findings. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Rubber dam use less stressful for children and dentists.

PubMed

Innes, Nicola

2012-06-01

Randomised controlled trial, single centre and operator. 72 patients (6-16 years) assessed as compliant, with no allergies, not on significant medication were divided into two groups by 'drawing sealed lots'. 234 fully erupted teeth were sealed. Molars and/or premolars were sealed dependant on age. Teeth were pre-cleaned with prophy paste. In the controls, teeth were isolated with buccal and lingual cotton rolls and salivary ejector in the intervention group a rubber dam was used. The same etching, rinsing and placement protocol was used in both arms. Outcomes were: patients' subjective measures of pain using a visual analogue scale; blood pressure (before and after treatment), breath rate, pulse rate and skin resistance at five time points. The operator's pulse rate was measured and they completed a questionnaire on subjective mental and physical stress following treatment. Treatment times were recorded. The breath rate was significantly (P < 0.05) lower and the skin resistance level was significantly higher during treatment with rubber dam compared to the control group. Subjective pain perception was significantly lower for the test group. The treatment time needed for the fissure sealing procedure was 12.4% less in the test group. The authors state; '... in the hands of an experienced dentist, isolation with rubber dam is less stressful for children and adolescents than isolation with cotton rolls, and can save valuable treatment time.' The operator's stress measures were lower with rubber dam and treatment time was reduced.

Thermoset recycling via high-pressure high-temperature sintering: Revisiting the effect of interchange chemistry

NASA Astrophysics Data System (ADS)

Morin, Jeremy Edward

In 1844 Charles Goodyear obtained U.S. Patent #3,633 for his "Gum Elastic Composition". In a published circular, which describes his patent for the sulfur vulcanization of gum elastic composition, he stated: "No degree of heat, without blaze, can melt it (rubber)... It resists the most powerful chemical reagents. Aquafortis (nitric acid), sulphuric acid, essential and common oils, turpentine and other solvents... ..." Goodyear's sulfur vulcanization of rubber fueled much of the industrial revolution and made transportation possible, as it exists today. In doing so, Goodyear created one of the most difficult materials to recycle. Rubber will not melt, dissolve, or lend itself to the usual methods of chemical decomposition. Ironically, Goodyear recognized this problem and in 1853 he patented the process of adding ground rubber to virgin material, now currently known as regrind blending. Today, scrap tires represent one of the most serious sources of pollution in the world. Studies estimate that there are roughly 2 billion scrap tires in U.S. landfills and more are being added at a rate of over 273 million tires per year. Current methods of recycling waste tires are crude, ineffective, and use rubber powder as a low cost filler instead of a new rubber. The groundwork for a very simple and effective method of producing high-quality rubber goods using 100% scrap rubber was discovered in 1944 by A. V. Tobolsky et al. This application, however, was not recognized until recently in our laboratory. The process as studied to date represents a method of creating quality, high-value added rubber goods with nothing other than heat and pressure. High pressure is required to obtain a void-free compaction of the rubber particles by forcing all of the free surfaces into intimate contact. High temperature then activates the chemical rearrangement, scission, and reformation of the chemical bonds thus providing new bridges between the once fractured interfaces. This occurs both within and between particles. The technique of high-pressure high-temperature sintering has worked on all types of thermoset materials. Typical mechanical properties for sintered SBR powder rubber are as follows: 1.3 MPa 100% Modulus, 12.0 MPa Tensile Strength and 300% Elongation at Break. The goal of this research is two-fold. First, to gain an understanding of the variables that control the process of high-pressure high-temperature sintering. Second, to study the factors governing the mechanism of fusion with the hope of controlling and exploiting this process so that tires can be recycled to produce high quality and high-value added products.

Differences in the impacts of formal and informal recreational trails on urban forest loss and tree structure.

PubMed

Ballantyne, Mark; Pickering, Catherine Marina

2015-08-15

Recreational trails are one of the most common types of infrastructure used for nature-based activities such as hiking and mountain biking worldwide. Depending on their design, location, construction, maintenance and use, these trails differ in their environmental impacts. There are few studies, however, comparing the impacts of different trail types including between formal management-created trails and informal visitor-created trails. Although both types of trails can be found in remote natural areas, dense networks of them often occur in forests close to cities where they experience intense visitor use. To assess the relative impacts of different recreational trails in urban forests, we compared the condition of the trail surface, loss of forest strata and changes in tree structure caused by seven types of trails (total network 46.1 km) traversing 17 remnants of an endangered urban forest in Australia. After mapping and classifying all trails, we assessed their impact on the forest condition at 125 sites (15 sites per trail type, plus 15 control sites within undisturbed forest). On the trail sites, the condition of the trail surface, distance from the trail edge to four forest strata (litter, understory, midstorey and tree cover) and structure of the tree-line were assessed. Informal trails generally had poorer surface conditions and were poorly-designed and located. Per site, formal and informal trails resulted in similar loss of forest strata, with wider trails resulting in greater loss of forest. Because there were more informal trails, however, they accounted for the greatest cumulative forest loss. Structural impacts varied, with the widest informal trails and all formal hardened trails resulting in similar reductions in canopy cover and tree density but an increase in saplings. These structural impacts are likely a function of the unregulated and intense use of large informal trails, and disturbance from the construction and maintenance of formal trails. The results demonstrate that different types of recreational trails vary in the type and range of impacts they cause to forests. They highlight the importance of careful consideration towards management options when dealing with trail networks especially in areas of high conservation value. Copyright © 2015 Elsevier Ltd. All rights reserved.

Area-Suction Boundary-Layer Control as Applied to the Trailing-Edge Flaps of a 35 Degree Swept-Wing Airplane

NASA Technical Reports Server (NTRS)

Cook, Woodrow L; Anderson, Seth B; Cooper, George E

1958-01-01

A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying area-suction boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effect of boundary-layer control in the handling qualities and operation of the airplane, particularly during landing. The wind-tunnel and flight tests indicated that area suction applied to the trailing-edge flaps produced significant increases in flap lift increment. Although the flap boundary-layer control reduced the stall speed only slightly, a reduction in minimum comfortable approach speed of about 12 knots was obtained.

Pressure distributions from subsonic tests of an advanced laminar-flow-control wing with leading- and trailing-edge flaps

NASA Technical Reports Server (NTRS)

Applin, Zachary T.; Gentry, Garl L., Jr.

1988-01-01

An unswept, semispan wing model equipped with full-span leading- and trailing-edge flaps was tested in the Langley 14- by 22-Foot Subsonic Tunnel to determine the effect of high-lift components on the aerodynamics of an advanced laminar-flow-control (LFC) airfoil section. Chordwise pressure distributions near the midsemispan were measured for four configurations: cruise, trailing-edge flap only, and trailing-edge flap with a leading-edge Krueger flap of either 0.10 or 0.12 chord. Part 1 of this report (under separate cover) presents a representative sample of the plotted pressure distribution data for each configuration tested. Part 2 presents the entire set of plotted and tabulated pressure distribution data. The data are presented without analysis.

49 CFR 571.224 - Standard No. 224; Rear impact protection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the vehicle is in motion. Nonstructural protrusions such as taillights, rubber bumpers, hinges and... deliver asphalt and other road building materials, in a controlled horizontal manner, into a lay down... protrusions such as taillights, hinges, rubber bumpers, and latches are excluded from the determination of the...

Weed control in a native rubber crop (Parthenium argentatum gray)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitworth, J.W.

1978-01-01

There is a renewed interest in the production of rubber from guayule (Parthenium argentatum). Excellent control of several weed species in guayule has been obtained with Varsol (a naphtha oil) at 30-40 gal/acre applied at the cotyledon stage. At this stage, guayule survival averaged 86-63% according to dose, but plants up to 10 days old at the time of treatment showed increasing tolerance. Paraffin was somewhat more selective that Varsol.

Over-expression of 3-hydroxy-3- methylglutaryl-coenzyme A reductase 1 (hmgr1) gene under super-promoter for enhanced latex biosynthesis in rubber tree (Hevea brasiliensis Muell. Arg.).

PubMed

Jayashree, R; Nazeem, P A; Rekha, K; Sreelatha, S; Thulaseedharan, A; Krishnakumar, R; Kala, R G; Vineetha, M; Leda, P; Jinu, U; Venkatachalam, P

2018-06-01

Natural rubber (cis-1, 4-polyisoprene) is being produced from bark laticifer cells of Hevea brasiliensis and the popular high latex yielding Indian rubber clones are easily prone to onset of tapping panel dryness syndrome (TPD) which is considered as a physiological syndrome affecting latex production either partially or completely. This report describes an efficient protocol for development of transgenic rubber plants by over-expression of 3-hydroxy 3-methylglutaryl Co-enzyme A reductase 1 (hmgr1) gene which is considered as rate limiting factor for latex biosynthesis via Agrobacterium-mediated transformation. The pBIB plasmid vector containing hmgr1 gene cloned under the control of a super-promoter was used for genetic transformation using embryogenic callus. Putatively transgenic cell lines were obtained on selection medium and produced plantlets with 44% regeneration efficiency. Transgene integration was confirmed by PCR amplification of 1.8 kb hmgr1 and 0.6 kb hpt genes from all putatively transformed callus lines as well as transgenic plants. Southern blot analysis showed the stable integration and presence of transgene in the transgenic plants. Over expression of hmgr1 transgene was determined by Northern blot hybridization, semi-quantitative PCR and real-time PCR (qRT-PCR) analysis. Accumulation of hmgr1 mRNA transcripts was more abundant in transgenic plants than control. Increased level of photosynthetic pigments, protein contents and HMGR enzyme activity was also noticed in transgenic plants over control. Interestingly, the latex yield was significantly enhanced in all transgenic plants compared to the control. The qRT-PCR results exhibit that the hmgr1 mRNA transcript levels was 160-fold more abundance in transgenic plants over untransformed control. These results altogether suggest that there is a positive correlation between latex yield and accumulation of mRNA transcripts level as well as HMGR enzyme activity in transgenic rubber plants. It is presumed that there is a possibility for enhanced level of latex biosynthesis in transgenic plants as the level of mRNA transcripts and HMGR enzyme activity is directly correlated with latex yield in rubber tree. Further, the present results clearly suggest that the quantification of HMGR enzyme activity in young seedlings will be highly beneficial for early selection of high latex yielding plants in rubber breeding programs. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Laticifer-Specific cis-Prenyltransferase Silencing Affects the Rubber, Triterpene, and Inulin Content of Taraxacum brevicorniculatum12[C][W

PubMed Central

Post, Janina; van Deenen, Nicole; Fricke, Julia; Kowalski, Natalie; Wurbs, David; Schaller, Hubert; Eisenreich, Wolfgang; Huber, Claudia; Twyman, Richard M.; Prüfer, Dirk; Gronover, Christian Schulze

2012-01-01

Certain Taraxacum species, such as Taraxacum koksaghyz and Taraxacum brevicorniculatum, produce large amounts of high-quality natural rubber in their latex, the milky cytoplasm of specialized cells known as laticifers. This high-molecular mass biopolymer consists mainly of poly(cis-1,4-isoprene) and is deposited in rubber particles by particle-bound enzymes that carry out the stereospecific condensation of isopentenyl diphosphate units. The polymer configuration suggests that the chain-elongating enzyme (rubber transferase; EC 2.5.1.20) is a cis-prenyltransferase (CPT). Here, we present a comprehensive analysis of transgenic T. brevicorniculatum plants in which the expression of three recently isolated CPTs known to be associated with rubber particles (TbCPT1 to -3) was heavily depleted by laticifer-specific RNA interference (RNAi). Analysis of the CPT-RNAi plants by nuclear magnetic resonance, size-exclusion chromatography, and gas chromatography-mass spectrometry indicated a significant reduction in rubber biosynthesis and a corresponding 50% increase in the levels of triterpenes and the main storage carbohydrate, inulin. Transmission electron microscopy revealed that the laticifers in CPT-RNAi plants contained fewer and smaller rubber particles than wild-type laticifers. We also observed lower activity of hydroxymethylglutaryl-coenzyme A reductase, the key enzyme in the mevalonate pathway, reflecting homeostatic control of the isopentenyl diphosphate pool. To our knowledge, this is the first in planta demonstration of latex-specific CPT activity in rubber biosynthesis. PMID:22238421

Trail Pheromone of the Argentine Ant, Linepithema humile (Mayr) (Hymenoptera: Formicidae)

PubMed Central

Choe, Dong-Hwan; Villafuerte, David B.; Tsutsui, Neil D.

2012-01-01

The Argentine ant (Linepithema humile) is recognized as one of the world's most damaging invasive species. One reason for the ecological dominance of introduced Argentine ant populations is their ability to dominate food and habitat resources through the rapid mobilization and recruitment of thousands of workers. More than 30 years ago, studies showed that (Z)-9-hexadecenal strongly attracted Argentine ant workers in a multi-choice olfactometer, suggesting that (Z)-9-hexadecenal might be the trail pheromone, or a component of a trail pheromone mixture. Since then, numerous studies have considered (Z)-9-hexadecenal as the key component of the Argentine ant trails. Here, we report the first chemical analyses of the trails laid by living Argentine ants and find that (Z)-9-hexadecenal is not present in a detectible quantity. Instead, two iridoids, dolichodial and iridomyrmecin, appear to be the primary chemical constituents of the trails. Laboratory choice tests confirmed that Argentine ants were attracted to artificial trails comprised of these two chemicals significantly more often than control trails. Although (Z)-9-hexadecenal was not detected in natural trails, supplementation of artificial dolichodial+iridomyrmecin trails with an extremely low concentraion of (Z)-9-hexadecenal did increase the efficacy of the trail-following behavior. In stark contrast with previous dogma, our study suggests that dolichodial and iridomyrmecin are major components of the Argentine ant trail pheromone. (Z)-9-hexadecenal may act in an additive manner with these iridoids, but it does not occur in detectable quantities in Argentine ant recruitment trails. PMID:23028739

Decreased placental and maternal serum TRAIL-R2 levels are associated with placenta accreta.

PubMed

Oztas, Efser; Ozler, Sibel; Ersoy, Ali Ozgur; Ersoy, Ebru; Caglar, Ali Turhan; Uygur, Dilek; Yucel, Aykan; Ergin, Merve; Danisman, Nuri

2016-03-01

TNF-related apoptosis-inducing ligand receptor-2 (TRAIL-R2) is produced both by decidual and trophoblast cells during pregnancy and known to participate in apoptosis. In this study, we aimed to determine and to compare maternal serum and placental TRAIL-R2 levels in patients with placenta accreta, non-adherent placenta previa and in healthy pregnancies. We also aimed to analyze the association of placenta accreta with the occurrence of previous C-sections. A total of 82 pregnant women were enrolled in this case-control study (27 placenta accreta patients, 26 non-adherent placenta previa patients and 29 age-, and BMI-matched healthy, uncomplicated pregnant controls). TRAIL-R2 levels were studied in both maternal serum and placental tissue homogenates. Determining the best predictor(s) which discriminate placenta accreta was analyzed by multiple logistic regression analyses. Adjusted odds ratios and 95% confidence intervals were also calculated. Both placental and serum TRAIL-R2 levels were significantly lower in placenta accreta group (median 34.82 pg/mg and 19.85 pg/mL, respectively) when compared with both non-adherent placenta previa (median 39.24 pg/mg and 25.99 pg/mL, respectively) and the control groups (median 41.62 pg/mg and 25.87 pg/mL, respectively) (p < 0.05). Placental TRAIL-R2 levels and previous cesarean section were found to be significantly associated with placenta accreta (OR: 0.934 95% CI 0.883-0.987, p = 0.016 and OR:7.725 95% CI: 2.717-21.965, p < 0.001, respectively). Placental and serum TRAIL-R2 levels were positively correlated. Decreased levels of placental TRAIL-R2 and previous history of cesarean section were found to be significantly associated with placenta accreta, suggesting a possible role of apoptosis in abnormal trophoblast invasion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Serum zinc concentrations: contamination from laboratory equipment.

PubMed

Ralstin, J O; Schneider, P J; Blackstone, L; Ruberg, R L

1979-01-01

The following experiment was designed because of high serum zinc reported in patients who were reciving total parenteral nutrition (TPN) concentrations. Blood samples were collected, divided into 3 containers: a clean glass control test tube, a vacuum collecting tube with a rubber stopper, and paraffin clot activator. It was found that compared to glass control tubes, vacuum collection with rubber stoppers contributed an average of 76 +/- 14 microgram/dl of zinc as contaminants. Moreover, tubes with a rubber stopper and clot activator contributed 198 +/- 42 microgram/dl of zinc as contaminants. It is concluded that care must be used to avoid trace element contaminants when plasma zinc concentrations are analyzed. Without proper methodology, including selection of the container in which the sample is taken, erroneous results will be reported.

Nanostructured magnesium oxide as cure activator for polychloroprene rubber.

PubMed

Kar, Sritama; Bhowmick, Anil K

2009-05-01

The aim of this research was to synthesize magnesium oxide nanoparticles and to use them as cure activator for polychloroprene rubber (CR). The effects of counterions of magnesium salts on the homogeneous phase precipitation reaction to control size, monodispersity, crystallinity, and morphology of Mg(OH)2 nanoparticles were also investigated. Magnesium oxide nanoparticles were synthesized by optimizing the calcination temperature of Mg(OH)2 nanoparticles. Finally, the MgO nanoparticles were dispersed in polychloroprene rubber (CR) solution along with zinc oxide (ZnO) powder. The influence of MgO nanoparticles on the mechanical, dynamic mechanical and thermal properties of the resulting nanocomposites was quantified. The modulus and strength of ZnO-cured polychloroprene rubber with 4% MgO nanoparticles appeared to be superior to those with ZnO particles or ZnO with rubber grade MgO particles. These composites were further characterized by transmission electron microscopy and infrared spectroscopy in order to understand the morphology of the resulting system and the load transfer mechanism.

Rubber friction and tire dynamics.

PubMed

Persson, B N J

2011-01-12

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

Trail pheromone disruption of Argentine ant trail formation and foraging.

PubMed

Suckling, David Maxwell; Peck, Robert W; Stringer, Lloyd D; Snook, Kirsten; Banko, Paul C

2010-01-01

Trail pheromone disruption of invasive ants is a novel tactic that builds on the development of pheromone-based pest management in other insects. Argentine ant trail pheromone, (Z)-9-hexadecenal, was formulated as a micro-encapsulated sprayable particle and applied against Argentine ant populations in 400 m2 field plots in Hawai'i Volcanoes National Park. A widely dispersed point source strategy for trail pheromone disruption was used. Traffic rates of ants in bioassays of treated filter paper, protected from rainfall and sunlight, indicated the presence of behaviorally significant quantities of pheromone being released from the formulation for up to 59 days. The proportion of plots, under trade wind conditions (2–3 m s−1), with visible trails was reduced for up to 14 days following treatment, and the number of foraging ants at randomly placed tuna-bait cards was similarly reduced. The success of these trail pheromone disruption trials in a natural ecosystem highlights the potential of this method for control of invasive ant species in this and other environments.

Laboratory and field studies of guayule modified to overexpress HMGR

USDA-ARS?s Scientific Manuscript database

We report the genetic modification of guayule to overexpress the isoprenoid pathway enzyme HMGR. The rubber content of two-month old in vitro transformed plantlets showed a 65% increase in rubber over the control for one line (HMGR6), and lower resin for another (HMGR2). In field evaluations HMGR6...

40 CFR 721.4100 - Tris(disubstituted alkyl) het-er-o-cy-cle.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for... substance is present in a plastic, an elastomer, a rubber matrix, or in a solution. (iii) Industrial... substance imported in a plastic, an elastomer, a rubber matrix, or in a solution, such that inhalation is...

40 CFR 721.4100 - Tris(disubstituted alkyl) het-er-o-cy-cle.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for... substance is present in a plastic, an elastomer, a rubber matrix, or in a solution. (iii) Industrial... substance imported in a plastic, an elastomer, a rubber matrix, or in a solution, such that inhalation is...

A rubber-covered ceramic weapon reduces the incidence of dental trauma in recruits during combat basic training.

PubMed

Becker, Talia; Ashkenazi, Malka

2011-10-01

The effect of a rubber-covered ceramic weapon was assessed on the incidence of dental trauma during basic training, since soldiers are more at risk of impact from a personal weapon. Dental files of soldiers (n = 4,542), who completed 8 months of training during 2008, were analyzed for incidence and type of dental trauma from a personal weapon. A rubber-covered ceramic weapon (n = 2,972) or a conventional one (n = 1,570, control) was used. Dental trauma was 0.4% per 8 months (0.6% per year) from the ceramic weapon and 1.5% per 8 months (2.3% per year) from the conventional one (p<0.001). The most prevalent type of injury was a simple/noncomplicated crown fracture (82% in study group, 75% in control group). The ceramic weapon significantly reduced dental trauma by diminishing the impact while in direct contact with the teeth or by absorbing and/or distributing the impact force. In conclusion, when possible a rubber-covered ceramic weapon should be preferred for basic combat training.

Molecular identification and characterization of the pyruvate decarboxylase gene family associated with latex regeneration and stress response in rubber tree.

PubMed

Long, Xiangyu; He, Bin; Wang, Chuang; Fang, Yongjun; Qi, Jiyan; Tang, Chaorong

2015-02-01

In plants, ethanolic fermentation occurs not only under anaerobic conditions but also under aerobic conditions, and involves carbohydrate and energy metabolism. Pyruvate decarboxylase (PDC) is the first and the key enzyme of ethanolic fermentation, which branches off the main glycolytic pathway at pyruvate. Here, four PDC genes were isolated and identified in a rubber tree, and the protein sequences they encode are very similar. The expression patterns of HbPDC4 correlated well with tapping-simulated rubber productivity in virgin rubber trees, indicating it plays an important role in regulating glycometabolism during latex regeneration. HbPDC1, HbPDC2 and HbPDC3 had striking expressional responses in leaves and bark to drought, low temperature and high temperature stresses, indicating that the HbPDC genes are involve in self-protection and defense in response to various abiotic and biotic stresses during rubber tree growth and development. To understand ethanolic fermentation in rubber trees, it will be necessary to perform an in-depth study of the regulatory pathways controlling the HbPDCs in the future. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Composite Elastic Skins for Shape-Changing Structures

NASA Technical Reports Server (NTRS)

Cagle, Christopher M.; Schlecht, Robin W.

2007-01-01

Composite elastic skins having tailorable mechanical properties have been invented for covering shape-changing ( morphable ) structures. These skins are intended especially for use on advanced aircraft that change shapes in order to assume different aerodynamic properties. Many of the proposals for aircraft that could perform large aerodynamic shape changes require flexible skins that could follow shape changes of internal structures driven by actuators. Examples of such shape changes can include growth or shrinkage of bumps, conformal changes in wing planforms, cambers, twists, and bending of integrated leading- and trailing-edge flaps. Prior to this invention, there was no way of providing smooth aerodynamic surfaces capable of large deflections while maintaining smoothness and sufficient rigidity. Although latex rubber, silicone rubber, and similar conventional materials can be made into smooth coverings, they are not suitable for this purpose because, in order to impart required stiffness against out-of-plane bending, it would be necessary to make the coverings excessively thick, thereby necessitating the use of impractically large actuation forces. The basic idea of the invention is that of smoothly wrapping an underlying variable structure with a smooth skin that can be stretched or otherwise warped with low actuation force in one or both in-plane direction(s) and is relatively stiff against out-of-plane bending. It is envisioned that a skin according to the invention could be stretched as much as 20 percent in a desired direction. Because this basic idea admits of numerous variations, the following description is necessarily oversimplified for the sake of brevity.

Disturbances in body ownership in schizophrenia: evidence from the rubber hand illusion and case study of a spontaneous out-of-body experience.

PubMed

Thakkar, Katharine N; Nichols, Heathman S; McIntosh, Lindsey G; Park, Sohee

2011-01-01

A weakened sense of self may contribute to psychotic experiences. Body ownership, one component of self-awareness, can be studied with the rubber hand illusion (RHI). Watching a rubber hand being stroked while one's unseen hand is stroked synchronously can lead to a sense of ownership over the rubber hand, a shift in perceived position of the real hand, and a limb-specific drop in stimulated hand temperature. We aimed to assess the RHI in schizophrenia using quantifiable measures: proprioceptive drift and stimulation-dependent changes in hand temperature. The RHI was elicited in 24 schizophrenia patients and 21 matched controls by placing their unseen hand adjacent to a visible rubber hand and brushing real and rubber hands synchronously or asynchronously. Perceived finger location was measured before and after stimulation. Hand temperature was taken before and during stimulation. Subjective strength of the illusion was assessed by a questionnaire. Across groups, the RHI was stronger during synchronous stimulation, indicated by self-report and proprioceptive drift. Patients reported a stronger RHI than controls. Self-reported strength of RHI was associated with schizotypy in controls Proprioceptive drift was larger in patients, but only following synchronous stimulation. Further, we observed stimulation-dependent changes in skin temperature. During right hand stimulation, temperature dropped in the stimulated hand and rose in the unstimulated hand. Interestingly, induction of RHI led to an out-of-body experience in one patient, linking body disownership and psychotic experiences. The RHI is quantitatively and qualitatively stronger in schizophrenia. These findings suggest that patients have a more flexible body representation and weakened sense of self, and potentially indicate abnormalities in temporo-parietal networks implicated in body ownership. Further, results suggest that these body ownership disturbances might be at the heart of a subset of the pathognomonic delusions of passivity.

Disturbances in Body Ownership in Schizophrenia: Evidence from the Rubber Hand Illusion and Case Study of a Spontaneous Out-of-Body Experience

PubMed Central

Thakkar, Katharine N.; Nichols, Heathman S.; McIntosh, Lindsey G.; Park, Sohee

2011-01-01

Background A weakened sense of self may contribute to psychotic experiences. Body ownership, one component of self-awareness, can be studied with the rubber hand illusion (RHI). Watching a rubber hand being stroked while one's unseen hand is stroked synchronously can lead to a sense of ownership over the rubber hand, a shift in perceived position of the real hand, and a limb-specific drop in stimulated hand temperature. We aimed to assess the RHI in schizophrenia using quantifiable measures: proprioceptive drift and stimulation-dependent changes in hand temperature. Methods The RHI was elicited in 24 schizophrenia patients and 21 matched controls by placing their unseen hand adjacent to a visible rubber hand and brushing real and rubber hands synchronously or asynchronously. Perceived finger location was measured before and after stimulation. Hand temperature was taken before and during stimulation. Subjective strength of the illusion was assessed by a questionnaire. Results Across groups, the RHI was stronger during synchronous stimulation, indicated by self-report and proprioceptive drift. Patients reported a stronger RHI than controls. Self-reported strength of RHI was associated with schizotypy in controls Proprioceptive drift was larger in patients, but only following synchronous stimulation. Further, we observed stimulation-dependent changes in skin temperature. During right hand stimulation, temperature dropped in the stimulated hand and rose in the unstimulated hand. Interestingly, induction of RHI led to an out-of-body experience in one patient, linking body disownership and psychotic experiences. Conclusions The RHI is quantitatively and qualitatively stronger in schizophrenia. These findings suggest that patients have a more flexible body representation and weakened sense of self, and potentially indicate abnormalities in temporo-parietal networks implicated in body ownership. Further, results suggest that these body ownership disturbances might be at the heart of a subset of the pathognomonic delusions of passivity. PMID:22073126

Electronic Escape Trails for Firefighters

NASA Technical Reports Server (NTRS)

Jorgensen, Charles; Schipper, John; Betts, Bradley

2008-01-01

A proposed wireless-communication and data-processing system would exploit recent advances in radio-frequency identification devices (RFIDs) and software to establish information lifelines between firefighters in a burning building and a fire chief at a control station near but outside the building. The system would enable identification of trails that firefighters and others could follow to escape from the building, including identification of new trails should previously established trails become blocked. The system would include a transceiver unit and a computer at the control station, portable transceiver units carried by the firefighters in the building, and RFID tags that the firefighters would place at multiple locations as they move into and through the building (see figure). Each RFID tag, having a size of the order of a few centimeters, would include at least standard RFID circuitry and possibly sensors for measuring such other relevant environmental parameters as temperature, levels of light and sound, concentration of oxygen, concentrations of hazardous chemicals in smoke, and/or levels of nuclear radiation. The RFID tags would be activated and interrogated by the firefighters and control-station transceivers. Preferably, RFID tags would be configured to communicate with each other and with the firefighters units and the control station in an ordered sequence, with built-in redundancy. In a typical scenario, as firefighters moved through a building, they would scatter many RFID tags into smoke-obscured areas by use of a compressed-air gun. Alternatively or in addition, they would mark escape trails by dropping RFID tags at such points of interest as mantraps, hot spots, and trail waypoints. The RFID tags could be of different types, operating at different frequencies to identify their functions, and possibly responding by emitting audible beeps when activated by signals transmitted by transceiver units carried by nearby firefighters.

Rubber dam may increase the survival time of dental restorations.

PubMed

Keys, William; Carson, Susan J

2017-03-01

Data sourcesCochrane Oral Health's Trials Register, Cochrane Central Register of Controlled Trials (CENTRAL), Medline, Embase, LILACS, SciELO, Chinese BioMedical Literature Database, VIP, China National Knowledge Infrastructure, ClinicalTrials.gov, World Health Organization International Clinical Trials Registry Platform, OpenGrey and Sciencepaper Online databases. Handsearches in a number of journals.Study selectionRandomised controlled trials, including split-mouth studies assessing the effects of rubber dam isolation for restorative treatments in dental patients.Data extraction and synthesisTwo review authors independently screened the results of the electronic searches, extracted data and assessed the risk of bias of the included studies.ResultsFour studies involving a total of 1,270 patients were included. The studies were at high risk of bias. One trial was excluded from the analysis due to inconsistencies in the presented data. Restorations had a significantly higher survival rate in the rubber dam isolation group compared to the cotton roll isolation group at six months in participants receiving composite restorative treatment of non-carious cervical lesions (risk ratio (RR) 1.19, 95% confidence interval (CI) 1.04 to 1.37, very low-quality evidence). The rubber dam group had a lower risk of failure at two years in children undergoing proximal atraumatic restorative treatment in primary molars (hazard ratio (HR) 0.80, 95% CI 0.66 to 0.97, very low-quality evidence). One trial reported limited data showing that rubber dam usage during fissure sealing might shorten the treatment time. None of the included studies mentioned adverse effects or reported the direct cost of the treatment, or the level of patient acceptance/satisfaction. There was also no evidence evaluating the effects of rubber dam usage on the quality of the restorations.ConclusionsWe found some very low-quality evidence, from single studies, suggesting that rubber dam usage in dental direct restorative treatments may lead to a lower failure rate of the restorations, compared with the failure rate for cotton roll usage. Further high quality research evaluating the effects of rubber dam usage on different types of restorative treatments is required.

Forestry best management practices and sediment control at skidder stream crossings

Treesearch

Laura R. Wear; W. Michael Aust; M. Chad Bolding; Brian D. Strahm; Andrew C. Dolloff

2015-01-01

Stream crossings for skid trails have high sediment delivery ratios. Forestry Best Management Practices (BMPs) have proven to be effective for erosion control, but few studies have quantified the impact of various levels of BMPs on sedimentation. In this study, three skid-trail stream-crossing BMP treatments were installed on nine operational stream crossings (three...

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

NASA Technical Reports Server (NTRS)

Heinemann, K.; Brown, Jeff

1992-01-01

This report discusses progress made on NASA Cooperative Agreement NCC2-545, 'An Experimental Study of a Turbulent Boundary Layer in the Trailing-Edge Region of a Circulation-Control Airfoil' during the period 9/1/91 through 9/30/92. The study features 2-component laser Doppler velocimeter (LDV) measurements in the trailing edge and wake regions of a generic 2-dimensional circulation-control model. The final experimental phase of the study will be carried out in the Ames High Reynolds Number Channel 2 (HRC2) transonic blow-down-facility. During the 13-month period covered by this report, work continued on the development of the near-wall laser Doppler velocimeter (LDV) described in previous reports.

Fast and robust method for the determination of microstructure and composition in butadiene, styrene-butadiene, and isoprene rubber by near-infrared spectroscopy.

PubMed

Vilmin, Franck; Dussap, Claude; Coste, Nathalie

2006-06-01

In the tire industry, synthetic styrene-butadiene rubber (SBR), butadiene rubber (BR), and isoprene rubber (IR) elastomers are essential for conferring to the product its properties of grip and rolling resistance. Their physical properties depend on their chemical composition, i. e., their microstructure and styrene content, which must be accurately controlled. This paper describes a fast, robust, and highly reproducible near-infrared analytical method for the quantitative determination of the microstructure and styrene content. The quantitative models are calculated with the help of pure spectral profiles estimated from a partial least squares (PLS) regression, using (13)C nuclear magnetic resonance (NMR) as the reference method. This versatile approach allows the models to be applied over a large range of compositions, from a single BR to an SBR-IR blend. The resulting quantitative predictions are independent of the sample path length. As a consequence, the sample preparation is solvent free and simplified with a very fast (five minutes) hot filming step of a bulk polymer piece. No precise thickness control is required. Thus, the operator effect becomes negligible and the method is easily transferable. The root mean square error of prediction, depending on the rubber composition, is between 0.7% and 1.3%. The reproducibility standard error is less than 0.2% in every case.

Reduced adherence of Candida to silane-treated silicone rubber.

PubMed

Price, C L; Williams, D W; Waters, M G J; Coulthwaite, L; Verran, J; Taylor, R L; Stickler, D; Lewis, M A O

2005-07-01

Silicone rubber is widely used in the construction of medical devices that can provide an essential role in the treatment of human illness. However, subsequent microbial colonization of silicone rubber can result in clinical infection or device failure. The objective of this study was to determine the effectiveness of a novel silane-treated silicone rubber in inhibiting microbial adherence and material penetration. Test material was prepared by a combination of argon plasma discharge treatment and fluorinated silane coupling. Chemicophysical changes were then confirmed by X-ray photoelectron spectroscopy, contact-angle measurement, and atomic force microscopy. Two separate adherence assays and a material penetration assay assessed the performance of the new material against four strains of Candida species. Results showed a significant reduction (p < 0.01) of Candida albicans GDH 2346 adherence to silane-treated silicone compared with untreated controls. This reduction was still evident after the incorporation of saliva into the assay. Adherence inhibition also occurred with Candida tropicalis MMU and Candida krusei NCYC, although this was assay dependent. Reduced penetration of silane-treated silicone by Candida was evident when compared to untreated controls, plaster-processed silicone, and acrylic-processed silicone. To summarize, a novel silicone rubber material is described that inhibits both candidal adherence and material penetration. The clinical benefit and performance of this material remains to be determined. Copyright 2005 Wiley Periodicals, Inc.

The impact of glide phases on the trackability of hydrodynamic trails in harbour seals (Phoca vitulina).

PubMed

Wieskotten, S; Dehnhardt, G; Mauck, B; Miersch, L; Hanke, W

2010-11-01

The mystacial vibrissae of harbour seals (Phoca vitulina) constitute a highly sensitive hydrodynamic receptor system enabling the seals to detect and follow hydrodynamic trails. In the wild, hydrodynamic trails, as generated by swimming fish, consist of cyclic burst-and-glide phases, associated with various differences in the physical parameters of the trail. Here, we investigated the impact of glide phases on the trackability of differently aged hydrodynamic trails in a harbour seal. As fish are not easily trained to swim certain paths with predetermined burst-and-glide phases, the respective hydrodynamic trails were generated using a remote-controlled miniature submarine. Gliding phases in hydrodynamic trails had a negative impact on the trackability when trails were 15 s old. The seal lost the generated trails more often within the transition zones, when the submarine switched from a burst to a glide moving pattern. Hydrodynamic parameter analysis (particle image velocimetry) revealed that the smaller dimensions and faster decay of hydrodynamic trails generated by the gliding submarine are responsible for the impaired success of the seal tracking the gliding phase. Furthermore, the change of gross water flow generated by the submarine from a rearwards-directed stream in the burst phase to a water flow passively dragged behind the submarine during gliding might influence the ability of the seal to follow the trail as this might cause a weaker deflection of the vibrissae. The possible ecological implications of intermittent swimming behaviour in fish for piscivorous predators are discussed.

Genetic variants in the tumor Necrosis Factor-Related Apoptosis-Inducing Ligand (TRAIL) do not contribute but Death Receptor (DR4) genes may contribute to susceptibility to head and neck cancer in Pakistani population.

PubMed

Sarwar, R; Mansoor, Q; Farooqi, A A; Shahzad, S; Fayyaz, S; Ismail, M

2015-12-19

TRAIL mediated signaling in cancer cells has emerged as one amongst the most deeply studied molecular phenomenon. Recent breakthroughs have shown that overexpression of anti-apoptotic proteins, inactivation of pro-apoptotic proteins, transcriptional downregulation of TRAIL, DR4/DR5, degradation of DR/DR5 are some of the mechanisms which dramatically abrogate TRAIL induced apoptosis in cancer cells. Data obtained through genetic studies has highlighted highly polymorphic nature of DR4 and in accordance with this concept, we investigated the association between Head and Neck Cancer and polymorphisms in TRAIL (1595 C/T) and DR4 (C626G and A1322G) gene. We selected 100 patients with Head and Neck Cancer and 100 healthy, sex and age matched volunteers randomly. C626G and A1322G in DR4 gene were analyzed using Polymerase Change Reaction (PCR) - Restriction Fragment Length Polymorphism (RFLP) and Amplification Refractory Mutation System (ARMS) techniques respectively. For TRAIL gene 1595 C>T genotypes, there was no statistically significant role of homozygous CC or TT in Head and Neck cancer. CC was 58% in patients and 49% in controls. CT was 30% in patients and 43% in controls. TT was 12% in patients and 8% in controls. Allele frequency for C was noted to be 0.73 (patients) and 0.705 (controls), p-value (1). For T, 0.025 (patients) and 0.001(controls), p-value (0.88). The genotyping for DR4 gene 626 C>G polymorphism was done for 100 head and neck cancer patients and 100 age and sex matched healthy controls. All the genotypes for the polymorphism were in Hardy-Weinberg Equilibrium. For DR4626 C>G genotype, CC was 10% in patients and 2% in controls. GC was 63% in patients and 40% in controls. GG was 27% in patients and 58% in controls. Interestingly, in DR4 genotyping, CC was predisposing factor and GG acted as a protective factor. Allele frequency for C was noted to be 0.41 (patients) and 0.22 (controls), p-value (0.81). For G, 0.585 (patients) and 0.78 (controls), p-value (0.867). For the A1322G polymorphism, TT was 23% in patients and 36% in controls with a p-value 0.09 (table 6). CT was statistically significant in patients (45%) and controls (28%), p-value 0.04. CC was non-significant in patients (32%) and controls (36%), p-value 0.62 (table 6). C allele was 0.45% in patients and 0.5% in controls. T allele was 0.54% in patients and 0.5% in controls. Future studies must converge on somatic mutations, epigenetic mutations and expression analysis of TRAIL and DR4 to get a step closer to individualized medicine.

40 CFR 721.10579 - Carbon black derived from the pyrolysis of rubber tire shreds (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Carbon black derived from the pyrolysis of rubber tire shreds (generic). 721.10579 Section 721.10579 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical...

Decoy receptors block TRAIL sensitivity at a supracellular level: the role of stromal cells in controlling tumour TRAIL sensitivity.

PubMed

O'Leary, L; van der Sloot, A M; Reis, C R; Deegan, S; Ryan, A E; Dhami, S P S; Murillo, L S; Cool, R H; Correa de Sampaio, P; Thompson, K; Murphy, G; Quax, W J; Serrano, L; Samali, A; Szegezdi, E

2016-03-10

Tumour necrosis factor-related apoptosis-inducing ligand (TRAIL) is a death ligand cytokine known for its cytotoxic activity against malignantly transformed cells. TRAIL induces cell death through binding to death receptors DR4 and DR5. The inhibitory decoy receptors (DcR1 and DcR2) co-expressed with death receptor 4 (DR4)/DR5 on the same cell can block the transmission of the apoptotic signal. Here, we show that DcRs also regulate TRAIL sensitivity at a supracellular level and thus represent a mechanism by which the microenvironment can diminish tumour TRAIL sensitivity. Mathematical modelling and layered or spheroid stroma-extracellular matrix-tumour cultures were used to model the tumour microenvironment. By engineering TRAIL to escape binding by DcRs, we found that DcRs do not only act in a cell-autonomous or cis-regulatory manner, but also exert trans-cellular regulation originating from stromal cells and affect tumour cells, highlighting the potent inhibitory effect of DcRs in the tumour tissue and the necessity of selective targeting of the two death-inducing TRAIL receptors to maximise efficacy.

The effect of minimum impact education on visitor spatial behavior in parks and protected areas: An experimental investigation using GPS-based tracking.

PubMed

Kidd, Abigail M; Monz, Christopher; D'Antonio, Ashley; Manning, Robert E; Reigner, Nathan; Goonan, Kelly A; Jacobi, Charles

2015-10-01

The unmanaged impacts of recreation and tourism can often result in unacceptable changes in resource conditions and quality of the visitor experience. Minimum impact visitor education programs aim to reduce the impacts of recreation by altering visitor behaviors. Specifically, education seeks to reduce impacts resulting from lack of knowledge both about the consequences of one's actions and impact-minimizing best practices. In this study, three different on-site minimum impact education strategies ("treatments") and a control condition were applied on the trails and summit area of Sargent Mountain in Acadia National Park, Maine. Treatment conditions were designed to encourage visitors to stay on marked trails and minimize off-trail travel. Treatments included a message delivered via personal contact, and both an ecological-based message and an amenity-based message posted on signs located alongside the trail. A control condition of current trail markings and directional signs was also assessed. The efficacy of the messaging was evaluated through the use of Global Positioning System (GPS) tracking of visitor spatial behavior on/off trails. Spatial analysis of GPS tracks revealed statistically significant differences among treatments, with the personal contact treatment yielding significantly less dispersion of visitors on the mountain summit. Results also indicate that the signs deployed in the study were ineffective at limiting off-trail use beyond what can be accomplished with trail markers and directional signs. These findings suggest that personal contact by a uniformed ranger or volunteer may be the most effective means of message delivery for on-site minimum impact education. Copyright © 2015 Elsevier Ltd. All rights reserved.

Cancer risk in the rubber industry: a review of the recent epidemiological evidence

PubMed Central

Kogevinas, M.; Sala, M.; Boffetta, P.; Kazerouni, N.; Kromhout, H.; Hoar-Zahm, S.

1998-01-01

OBJECTIVES: To examine the recent epidemiological evidence on cancer risk among workers in the rubber industry. METHODS: Epidemiological studies published after the last detailed review by the International Agency for Research on Cancer (IARC) in 1982 were reviewed. 12 cohort studies in nine countries that examined distinct populations of workers in the rubber industry, seven industry based nested case-control studies, 48 community based case-control studies in 16 countries, and 23 studies based on administrative data that reported risks for employment in the rubber industry were identified. RESULTS: Excess risks of bladder cancer, lung cancer, and leukaemia were found in most studies, with risks above 1.5 in about half of the studies. A moderate excess risk for laryngeal cancer was consistent across studies. Excess risks were found in a few studies for cancers of the oesophagus, stomach, colon, liver, pancreas, skin, prostate, kidney, brain, and thyroid, and for malignant lymphoma and multiple myeloma, but overall results were not consistent for these neoplasms. CONCLUSIONS: Magnitude of the observed risks varied considerably between studies, but overall the findings indicate the presence of a widespread moderate increased cancer risk among rubber workers. The most consistent results were for bladder, laryngeal, and lung cancer and for leukaemia. Excess risks were also found for other neoplasms but an evaluation of the consistency of the findings is difficult because of the possible selective reporting of results. Recent studies do not provide information associating specific exposures with cancer risk. The preventive measures taken in the rubber industry in recent years may decrease risks, but this has not been documented yet in epidemiological studies.   PMID:9536156

Trail Pheromone Disruption of Argentine Ant Trail Formation and Foraging

USGS Publications Warehouse

Suckling, D.M.; Peck, R.W.; Stringer, L.D.; Snook, K.; Banko, P.C.

2010-01-01

Trail pheromone disruption of invasive ants is a novel tactic that builds on the development of pheromone-based pest management in other insects. Argentine ant trail pheromone, (Z)-9-hexadecenal, was formulated as a micro-encapsulated sprayable particle and applied against Argentine ant populations in 400 m2 field plots in Hawai'i Volcanoes National Park. A widely dispersed point source strategy for trail pheromone disruption was used. Traffic rates of ants in bioassays of treated filter paper, protected from rainfall and sunlight, indicated the presence of behaviorally significant quantities of pheromone being released from the formulation for up to 59 days. The proportion of plots, under trade wind conditions (2-3 m s-1), with visible trails was reduced for up to 14 days following treatment, and the number of foraging ants at randomly placed tuna-bait cards was similarly reduced. The success of these trail pheromone disruption trials in a natural ecosystem highlights the potential of this method for control of invasive ant species in this and other environments. ?? Springer Science+Business Media, LLC 2010.

Rubber dam isolation for restorative treatment in dental patients.

PubMed

Wang, Yan; Li, Chunjie; Yuan, He; Wong, May Cm; Zou, Jing; Shi, Zongdao; Zhou, Xuedong

2016-09-20

Successful restorations in dental patients depend largely on the effective control of moisture and microbes during the procedure. The rubber dam technique has been one of the most widely used isolation methods in dental restorative treatments. The evidence on the effects of rubber dam usage on the longevity of dental restorations is conflicting. Therefore, it is important to summarise the available evidence to determine the effects of this method. To assess the effects of rubber dam isolation compared with other types of isolation used for direct and indirect restorative treatments in dental patients. We searched the following electronic databases: Cochrane Oral Health's Trials Register (searched 17 August 2016), Cochrane Central Register of Controlled Trials (CENTRAL; 2016, Issue 7) in the Cochrane Library (searched 17 August 2016), MEDLINE Ovid (1946 to 17 August 2016), Embase Ovid (1980 to 17 August 2016), LILACS BIREME Virtual Health Library (Latin American and Caribbean Health Science Information database; 1982 to 17 August 2016), SciELO BIREME Virtual Health Library (1998 to 17 August 2016), Chinese BioMedical Literature Database (CBM, in Chinese) (1978 to 30 August 2016), VIP (in Chinese) (1989 to 30 August 2016), and China National Knowledge Infrastructure (CNKI, in Chinese) (1994 to 30 August 2016). We searched ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform, OpenGrey and Sciencepaper Online (in Chinese) for ongoing trials. There were no restrictions on the language or date of publication when searching the electronic databases. We included randomised controlled trials (including split-mouth trials) assessing the effects of rubber dam isolation for restorative treatments in dental patients. Two review authors independently screened the results of the electronic searches, extracted data and assessed the risk of bias of the included studies. We resolved disagreement by discussion. We included four studies that analysed 1270 participants (among which 233 participants were lost to follow-up). All the included studies were at high risk of bias. We excluded one trial from the analysis due to inconsistencies in the presented data.The results indicated that dental restorations had a significantly higher survival rate in the rubber dam isolation group compared to the cotton roll isolation group at six months in participants receiving composite restorative treatment of non-carious cervical lesions (risk ratio (RR) 1.19, 95% confidence interval (CI) 1.04 to 1.37, very low-quality evidence). It also showed that the rubber dam group had a lower risk of failure at two years in children undergoing proximal atraumatic restorative treatment in primary molars (hazard ratio (HR) 0.80, 95% CI 0.66 to 0.97, very low-quality evidence). One trial reported limited data showing that rubber dam usage during fissure sealing might shorten the treatment time. None of the included studies mentioned adverse effects or reported the direct cost of the treatment, or the level of patient acceptance/satisfaction. There was also no evidence evaluating the effects of rubber dam usage on the quality of the restorations. We found some very low-quality evidence, from single studies, suggesting that rubber dam usage in dental direct restorative treatments may lead to a lower failure rate of the restorations, compared with the failure rate for cotton roll usage. Further high quality research evaluating the effects of rubber dam usage on different types of restorative treatments is required.

Motile bacteria in a critical fluid mixture

NASA Astrophysics Data System (ADS)

Koumakis, Nick; Devailly, Clémence; Poon, Wilson C. K.

2018-06-01

We studied the swimming of Escherichia coli bacteria in the vicinity of the critical point in a solution of the nonionic surfactant C12E5 in buffer solution. In phase-contrast microscopy, each swimming cell produces a transient trail behind itself lasting several seconds. Comparing quantitative image analysis with simulations show that these trails are due to local phase reorganization triggered by differential adsorption. This contrasts with similar trails seen in bacteria swimming in liquid crystals, which are due to shear effects. We show how our trails are controlled, and use them to probe the structure and dynamics of critical fluctuations in the fluid medium.

Natural Rubber Nanocomposite with Human-Tissue-Like Mechanical Characteristic

NASA Astrophysics Data System (ADS)

Murniati, Riri; Novita, Nanda; Sutisna; Wibowo, Edy; Iskandar, Ferry; Abdullah, Mikrajuddin

2017-07-01

The blends of synthetic rubber and natural rubber with nanosilica were prepared using a blending technique in presence of different filler volume fraction. The effect of filler on morphological and mechanical characteristics was studied. Utilization of human cadaver in means of medical study has been commonly used primarily as tools of medical teaching and training such as surgery. Nonetheless, human cadaver brought inevitable problems. So it is necessary to find a substitute material that can be used to replace cadavers. In orthopaedics, the materials that resemble in mechanical properties to biological tissues are elastomers such as natural rubber (latex) and synthetic rubber (polyurethanes, silicones). This substitution material needs to consider the potential of Indonesia to help the development of the nation. Indonesia is the second largest country producer of natural rubber in the world. This paper aims to contribute to adjusting the mechanical properties of tissue-mimicking materials (TMMs) to the recommended range of biological tissue value and thus allow the development of phantoms with greater stability and similarity to human tissues. Repeatability for the phantom fabrication process was also explored. Characteristics were then compared to the control and mechanical characteristics of different human body part tissue. Nanosilica is the best filler to produce the best nanocomposite similarities with human tissue. We produced composites that approaching the properties of human internal tissues.

Behaviour of Steel Fibre Reinforced Rubberized Continuous Deep Beams

NASA Astrophysics Data System (ADS)

Sandeep, MS; Nagarajan, Praveen; Shashikala, A. P.

2018-03-01

Transfer girders and pier caps, which are in fact deep beams, are critical structural elements present in high-rise buildings and bridges respectively. During an earthquake, failure of lifeline structures like bridges and critical structural members like transfer girders will result in severe catastrophes. Ductility is the key factor that influences the resistance of any structural member against seismic action. Structural members cast using materials having higher ductility will possess higher seismic resistance. Previous research shows that concrete having rubber particles (rubcrete) possess better ductility and low density in comparison to ordinary concrete. The main hindrance to the use of rubcrete is the reduction in compressive and tensile strength of concrete due to the presence of rubber. If these undesirable properties of rubcrete can be controlled, a new cementitious composite with better ductility, seismic performance and economy can be developed. A combination of rubber particles and steel fibre has the potential to reduce the undesirable effect of rubcrete. In this paper, the effect of rubber particles and steel fibre in the behaviour of two-span continuous deep beams is studied experimentally. Based on the results, optimum proportions of steel fibre and rubber particles for getting good ductile behaviour with less reduction in collapse load is found out.

Mechanical Properties and Morphologies of Carboxyl-Terminated Butadiene Acrylonitrile Liquid Rubber/Epoxy Blends Compatibilized by Pre-Crosslinking.

PubMed

Xu, Shiai; Song, Xiaoxue; Cai, Yangben

2016-07-29

In order to enhance the compatibilization and interfacial adhesion between epoxy and liquid carboxyl-terminated butadiene acrylonitrile (CTBN) rubber, an initiator was introduced into the mixture and heated to initiate the cross-linking reaction of CTBN. After the addition of curing agents, the CTBN/epoxy blends with a localized interpenetrating network structure were prepared. The mechanical properties and morphologies of pre-crosslinked and non-crosslinked CTBN/epoxy blends were investigated. The results show that the tensile strength, elongation at break and impact strength of pre-crosslinked CTBN/epoxy blends are significantly higher than those of non-crosslinked CTBN/epoxy blends, which is primarily due to the enhanced interfacial strength caused by the chemical bond between the two phases and the localized interpenetrating network structure. Both pre-crosslinked and non-crosslinked CTBN/epoxy blends show a bimodal distribution of micron- and nano-sized rubber particles. However, pre-crosslinked CTBN/epoxy blends have smaller micron-sized rubber particles and larger nano-sized rubber particles than non-crosslinked CTBN/epoxy blends. The dynamic mechanical analysis shows that the storage modulus of pre-crosslinked CTBN/epoxy blends is higher than that of non-crosslinked CTBN/epoxy blends. The glass transition temperature of the CTBN phase in pre-crosslinked CTBN/epoxy blends increases slightly compared with the CTBN/epoxy system. The pre-crosslinking of rubber is a promising method for compatibilization and controlling the morphology of rubber-modified epoxy materials.

Mechanical Properties and Morphologies of Carboxyl-Terminated Butadiene Acrylonitrile Liquid Rubber/Epoxy Blends Compatibilized by Pre-Crosslinking

PubMed Central

Xu, Shiai; Song, Xiaoxue; Cai, Yangben

2016-01-01

In order to enhance the compatibilization and interfacial adhesion between epoxy and liquid carboxyl-terminated butadiene acrylonitrile (CTBN) rubber, an initiator was introduced into the mixture and heated to initiate the cross-linking reaction of CTBN. After the addition of curing agents, the CTBN/epoxy blends with a localized interpenetrating network structure were prepared. The mechanical properties and morphologies of pre-crosslinked and non-crosslinked CTBN/epoxy blends were investigated. The results show that the tensile strength, elongation at break and impact strength of pre-crosslinked CTBN/epoxy blends are significantly higher than those of non-crosslinked CTBN/epoxy blends, which is primarily due to the enhanced interfacial strength caused by the chemical bond between the two phases and the localized interpenetrating network structure. Both pre-crosslinked and non-crosslinked CTBN/epoxy blends show a bimodal distribution of micron- and nano-sized rubber particles. However, pre-crosslinked CTBN/epoxy blends have smaller micron-sized rubber particles and larger nano-sized rubber particles than non-crosslinked CTBN/epoxy blends. The dynamic mechanical analysis shows that the storage modulus of pre-crosslinked CTBN/epoxy blends is higher than that of non-crosslinked CTBN/epoxy blends. The glass transition temperature of the CTBN phase in pre-crosslinked CTBN/epoxy blends increases slightly compared with the CTBN/epoxy system. The pre-crosslinking of rubber is a promising method for compatibilization and controlling the morphology of rubber-modified epoxy materials. PMID:28773762

A method for the determination of syringe needle punctures in rubber stoppers using stereoscopic light microscopy.

PubMed

Platek, S Frank; Keisler, Mark A; Ranieri, Nicola; Reynolds, Todd W; Crowe, John B

2002-09-01

The ability to accurately determine the number of syringe needle penetration holes through the rubber stoppers in pharmaceutical vials and rubber septa in intravenous (i.v.) line and bag ports has been a critical factor in a number of forensic cases involving the thefts of controlled substances or suspected homicide by lethal injection. In the early 1990s, the microscopy and microanalysis group of the U.S. Food and Drug Administration's Forensic Chemistry Center (FCC) developed and implemented a method (unpublished) to locate needle punctures in rubber pharmaceutical vial stoppers. In 1996, as part of a multiple homicide investigation, the Indiana State Police Laboratory (ISPL) contacted the FCC for information on a method to identify and count syringe needle punctures through rubber stoppers in pharmaceutical vials. In a joint project and investigation using the FCC's needle hole location method and applying a method of puncture site mapping developed by the ISPL, a systematic method was developed to locate, identify, count, and map syringe punctures in rubber bottle stoppers or i.v. bag ports using microscopic analysis. The method requires documentation of punctures on both sides of the rubber stoppers and microscopic analysis of each suspect puncture site. The final result of an analysis using the method is a detailed diagram of puncture holes on both sides of a questioned stopper and a record of the minimum number of puncture holes through a stopper.

Is Body Dysmorphic Disorder Associated with Abnormal Bodily Self-Awareness? A Study Using the Rubber Hand Illusion

PubMed Central

Kaplan, Ryan A.; Enticott, Peter G.; Hohwy, Jakob; Castle, David J.; Rossell, Susan L.

2014-01-01

Evidence from past research suggests that behaviours and characteristics related to body dissatisfaction may be associated with greater instability of perceptual body image, possibly due to problems in the integration of body-related multisensory information. We investigated whether people with body dysmorphic disorder (BDD), a condition characterised by body image disturbances, demonstrated enhanced susceptibility to the rubber hand illusion (RHI), which arises as a result of multisensory integration processes when a rubber hand and the participant's hidden real hand are stimulated in synchrony. Overall, differences in RHI experience between the BDD group and healthy and schizophrenia control groups (n = 17 in each) were not significant. RHI strength, however, was positively associated with body dissatisfaction and related tendencies. For the healthy control group, proprioceptive drift towards the rubber hand was observed following synchronous but not asynchronous stimulation, a typical pattern when inducing the RHI. Similar drifts in proprioceptive awareness occurred for the BDD group irrespective of whether stimulation was synchronous or not. These results are discussed in terms of possible abnormalities in visual processing and multisensory integration among people with BDD. PMID:24925079

Gas turbine engine exhaust diffuser including circumferential vane

DOEpatents

Orosa, John A.; Matys, Pawel

2015-05-19

A flow passage defined between an inner and an outer boundary for guiding a fluid flow in an axial direction. A flow control vane is supported at a radial location between the inner and outer boundaries. A fluid discharge opening is provided for discharging a flow of the compressed fluid from a trailing edge of the vane, and a fluid control surface is provided adjacent to the fluid discharge opening and extends in the axial direction at the trailing edge of the vane. The fluid control surface has a curved trailing edge forming a Coanda surface. The fluid discharge opening is selectively provided with a compressed fluid to produce a Coanda effect along the control surface. The Coanda effect has a component in the radial direction effecting a turning of the fluid flow in the flow path radially inward or outward toward one of the inner and outer boundaries.

Bird Responses to Lowland Rainforest Conversion in Sumatran Smallholder Landscapes, Indonesia

PubMed Central

Clough, Yann; Toledo-Hernandez, Manuel; Arlettaz, Raphael; Mulyani, Yeni A.; Tscharntke, Teja

2016-01-01

Rapid land-use change in the tropics causes dramatic losses in biodiversity and associated functions. In Sumatra, Indonesia, lowland rainforest has mainly been transformed by smallholders into oil palm (Elaeis guineensis) and rubber (Hevea brasiliensis) monocultures, interspersed with jungle rubber (rubber agroforests) and a few forest remnants. In two regions of the Jambi province, we conducted point counts in 32 plots of four different land-use types (lowland rainforest, jungle rubber, rubber plantation and oil palm plantation) as well as in 16 nearby homegardens, representing a small-scale, traditional agricultural system. We analysed total bird abundance and bird abundance in feeding guilds, as well as species richness per point count visit, per plot, and per land-use system, to unveil the conservation importance and functional responses of birds in the different land-use types. In total, we identified 71 species from 24 families. Across the different land-use types, abundance did not significantly differ, but both species richness per visit and per plot were reduced in plantations. Feeding guild abundances between land-use types were variable, but homegardens were dominated by omnivores and granivores, and frugivorous birds were absent from monoculture rubber and oil palm. Jungle rubber played an important role in harbouring forest bird species and frugivores. Homegardens turned out to be of minor importance for conserving birds due to their low sizes, although collectively, they are used by many bird species. Changes in functional composition with land-use conversion may affect important ecosystem functions such as biological pest control, pollination, and seed dispersal. In conclusion, maintaining forest cover, including degraded forest and jungle rubber, is of utmost importance to the conservation of functional and taxonomic bird diversity. PMID:27224063

Bird Responses to Lowland Rainforest Conversion in Sumatran Smallholder Landscapes, Indonesia.

PubMed

Prabowo, Walesa Edho; Darras, Kevin; Clough, Yann; Toledo-Hernandez, Manuel; Arlettaz, Raphael; Mulyani, Yeni A; Tscharntke, Teja

2016-01-01

Rapid land-use change in the tropics causes dramatic losses in biodiversity and associated functions. In Sumatra, Indonesia, lowland rainforest has mainly been transformed by smallholders into oil palm (Elaeis guineensis) and rubber (Hevea brasiliensis) monocultures, interspersed with jungle rubber (rubber agroforests) and a few forest remnants. In two regions of the Jambi province, we conducted point counts in 32 plots of four different land-use types (lowland rainforest, jungle rubber, rubber plantation and oil palm plantation) as well as in 16 nearby homegardens, representing a small-scale, traditional agricultural system. We analysed total bird abundance and bird abundance in feeding guilds, as well as species richness per point count visit, per plot, and per land-use system, to unveil the conservation importance and functional responses of birds in the different land-use types. In total, we identified 71 species from 24 families. Across the different land-use types, abundance did not significantly differ, but both species richness per visit and per plot were reduced in plantations. Feeding guild abundances between land-use types were variable, but homegardens were dominated by omnivores and granivores, and frugivorous birds were absent from monoculture rubber and oil palm. Jungle rubber played an important role in harbouring forest bird species and frugivores. Homegardens turned out to be of minor importance for conserving birds due to their low sizes, although collectively, they are used by many bird species. Changes in functional composition with land-use conversion may affect important ecosystem functions such as biological pest control, pollination, and seed dispersal. In conclusion, maintaining forest cover, including degraded forest and jungle rubber, is of utmost importance to the conservation of functional and taxonomic bird diversity.

Comparison of microclimate in various land-use systems in Sumatra, Indonesia

NASA Astrophysics Data System (ADS)

Shekhar Badu, Chandra; Meijide, Ana; Gunawan, Dodo; Knohl, Alexander

2017-04-01

Deforestation and land-use changes are ongoing problems for rain forests in Indonesia. The conversion of forests to monocultures of rubber and oil palm plantations reduces not only biodiversity and carbon pools but also affects canopy structure, which is an important determinant of microclimate. There is, however, a lack of quantitative information characterizing the effect of land transformation on microclimate with a systematic experimental design. Here, we report observations microclimatic conditions (air temperature, relative humidity, soil moisture and soil temperature) on a daily, weekly and seasonal basis across four land-use systems (rain forest, jungle rubber, rubber plantation, oil palm plantation) in two near-by landscapes. The data set covers a period of approximately three years from April 2013 to March 2016 and includes one of the strongest El Nino-Southern Oscillation (ENSO) of the last decades. Mean air temperature, soil temperature, relative humidity, and vapour pressure deficit differed significantly between the four land-use systems whereas the mean soil moisture differed significantly between two landscapes. Air temperature, vapour pressure deficit and soil temperature were highest in oil palm and rubber plantations whereas lowest in forest and jungle rubber. Canopy openness was the most dominant control of microclimatic differences across the land-use systems. During the ENSO 2015, a significant increase in mean air temperature, soil temperature and vapour pressure deficit but a decrease in relative air humidity and soil moisture in all four land-use systems was found. The relative effect of ENSO was highest in forest and jungle rubber compared to rubber and oil palm plantations. In conclusion, conversion of forest to rubber and oil palm plantations has led to substantially warmer and drier microclimatic conditions than before.

Effect of local anaesthesia on short- and long-term pain induced by two bloodless castration methods in calves.

PubMed

Thüer, Susann; Mellema, Sibylle; Doherr, Marcus G; Wechsler, Beat; Nuss, Karl; Steiner, Adrian

2007-03-01

Behavioural and cortisol responses of calves were used as indicators of pain to assess short- and long-term effects of bloodless castration methods with and without local anaesthesia. Seventy calves, aged 21-28 days, were control handled (20) or castrated using the Burdizzo (25) or rubber ring technique (25). Either 10 mL lidocaine or NaCl were distributed in both spermatic cords and the scrotal neck. The plasma cortisol response was recorded for 72 h, and behavioural and clinical traits monitored over a three month period. Local anaesthesia reduced the level of indicators of acute pain after both the Burdizzo and rubber ring techniques. It did not, however, result in a totally painless castration. As there was evidence of chronic pain lasting for several weeks after rubber ring castration, the Burdizzo method is judged to be preferable to the rubber ring technique.

Artificial Turf: Contested Terrains for Precautionary Public Health with Particular Reference to Europe?

PubMed Central

Watterson, Andrew

2017-01-01

Millions of adults, children and teenagers use artificial sports pitches and playgrounds globally. Pitches are artificial grass and bases may be made up of crumb rubber from recycled tires or new rubber and sand. Player injury on pitches was a major concern. Now, debates about health focus on possible exposure and uptake of chemicals within pitch and base materials. Research has looked at potential risks to users from hazardous substances such as metals, volatile organic compounds, polycyclic aromatic hydrocarbons including benzo (a) (e) pyrenes and phthalates: some are carcinogens and others may be endocrine disruptors and have developmental reproductive effects. Small environmental monitoring and modelling studies, often with significant data gaps about exposure, range of substances monitored, occupational exposures, types of surfaces monitored and study length across seasons, indicated little risk to sports people and children but some risk to installation workers. A few, again often small, studies indicated potentially harmful human effects relating to skin, respiration and cancers. Only one widely cited biomonitoring study has been done and no rigorous cancer epidemiological studies exist. Unravelling exposures and uptake over decades may prove complex. European regulators have strengthened controls over crumb rubber chemicals, set different standards for toys and crumb rubber pitches. Bigger US studies now underway attempting to fill some of the data gaps will report between 2017 and 2019. Public health professionals in the meantime may draw on established principles to support greater caution in setting crumb rubber exposure limits and controls. PMID:28895924

Design of magneto-rheological mount for a cabin of heavy equipment vehicles

NASA Astrophysics Data System (ADS)

Yang, Soon-Yong; Do, Xuan Phu; Choi, Seung-Bok

2016-04-01

In this paper, magneto-rheological (MR) mount for a cabin of heavy equipment vehicles is designed for improving vibration isolation in both low and high frequency domains. The proposed mount consists of two principal parts of mount, rubber part and MR fluid path. The rubber part of existed mount and spring are used to change the stiffness and frequency characteristics for low vibration frequency range. The MR fluid path is a valve type structure using flow mode. In order to control the external magnetic field, a solenoid coil is placed in MR mount. Magnetic intensity analysis is then conducted to optimize dimensions using computer simulation. Experimental results show that magnetic field can reduce low frequency vibration. The results presented in this work indicate that proper application of MR fluid and rubber characteristic to devise MR mount can lead to the improvement of vibration control performance in both low and high frequency ranges.

Sex-specific trail pheromone mediates complex mate finding behavior in Anoplophora glabripennis.

PubMed

Hoover, Kelli; Keena, Melody; Nehme, Maya; Wang, Shifa; Meng, Peter; Zhang, Aijun

2014-02-01

Anoplophora glabripennis (Motsch.) is a polyphagous member of the Cerambycidae, and is considered, worldwide, to be one of the most serious quarantine pests of deciduous trees. We isolated four chemicals from the trail of A. glabripennis virgin and mated females that were not present in trails of mature males. These compounds were identified as 2-methyldocosane and (Z)-9-tricosene (major components), as well as (Z)-9-pentacosene and (Z)-7-pentacosene (minor components); every trail wash sample contained all four chemical components, although the amounts and ratios changed with age of the female. Males responded to the full pheromone blend, regardless of mating status, but virgin females chose the control over the pheromone, suggesting that they may use it as a spacing pheromone to avoid intraspecific competition and maximize resources. Virgin, but not mated, males also chose the major pheromone components in the absence of the minor components, over the control. Taken together, these results indicate that all four chemicals are components of the trail pheromone. The timing of production of the ratios of the pheromone blend components that produced positive responses from males coincided with the timing of sexual maturation of the female.

Development and Testing of the Phase 0 Autonomous Formation Flight Research System

NASA Technical Reports Server (NTRS)

Petersen, Shane; Fantini, Jay; Norlin, Ken; Theisen, John; Krasiewski, Steven

2004-01-01

The Autonomous Formation Flight (AFF) project was initiated in 1995 to demonstrate at least 10-percent drag reduction by positioning a trailing aircraft in the wingtip vortex of a leading aircraft. If successful, this technology would provide increased fuel savings, reduced emissions, and extended flight duration for fleet aircraft flying in formation. To demonstrate this technology, the AFF project at NASA Dryden Flight Research Center developed a system architecture incorporating two F-18 aircraft flying in leading-trailing formation. The system architecture has been designed to allow the trailing aircraft to maintain station-keeping position relative to the leading aircraft within +/-10 ft. Development of this architecture would be directed at the design and development of a computing system to feed surface position commands into the flight control computers, thereby controlling the longitudinal and lateral position of the trailing aircraft. In addition, modification to the instrumentation systems of both aircraft, pilot displays, and a means of broadcasting the leading aircraft inertial and global positioning system-based positional data to the trailing aircraft would be needed. This presentation focuses on the design and testing of the AFF Phase 0 research system.

The effect of TRAIL molecule on cell viability in in vitro beta cell culture.

PubMed

Tekmen, I; Ozyurt, D; Pekçetin, C; Buldan, Z

2007-06-01

Insulin-dependent diabetes mellitus (IDDM) is an organ-specific autoimmune disorder triggered by autoreactive T cells directed to pancreas beta-cell antigens. In this disorder, more than 90% of beta cells are destroyed. Cell death may be mediated via soluble or membrane-bound cell death ligands. One of these ligands may be tumour necrosis factor (TNF)-related apoptosis-inducing ligand (TRAIL), a member of the TNF-alpha superfamily. In the present study, we examined whether TRAIL had cytotoxic effects on adult rat pancreas beta cell cultures and INS1-E rat insulinoma cell line cultures or not. In this study, cell destruction models were built with TRAIL concentrations of 10, 100 and 1000 ng. 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) test was used for evaluating cell viability. It was detected that cell cultures with TRAIL added showed no differences statistically when compared with control cultures containing no toxic additions. These results showed that TRAIL did not have significant cytotoxic effects on pancreas beta cell culture and INS-1E rat insulinoma cell line cultures. Detection of the expression of TRAIL receptors and natural apoptosis inhibitor proteins will be favourable to investigate the resistance mechanisms to TRAIL-induced cell death in this cell culture system.

Improved hemocompatibility of silicone rubber extracorporeal tubing via solvent swelling-impregnation of S-nitroso-N-acetylpenicillamine (SNAP) and evaluation in rabbit thrombogenicity model.

PubMed

Brisbois, Elizabeth J; Major, Terry C; Goudie, Marcus J; Bartlett, Robert H; Meyerhoff, Mark E; Handa, Hitesh

2016-06-01

Blood-contacting devices, including extracorporeal circulation (ECC) circuits, can suffer from complications due to platelet activation and thrombus formation. Development of nitric oxide (NO) releasing polymers is one method to improve hemocompatibility, taking advantage of the ability of low levels of NO to prevent platelet activation/adhesion. In this study a novel solvent swelling method is used to load the walls of silicone rubber tubing with the NO donor S-nitroso-N-acetylpenicillamine (SNAP). This SNAP-silicone rubber tubing exhibits an NO flux of ca. 1×10(-10)molcm(-2)min(-1), which mimics the range of NO release from the normal endothelium, which is stable for at least 4h. Images of the tubing before and after swelling, obtained via scanning electron microscopy, demonstrate that this swelling method has little effect on the surface properties of the tubing. The SNAP-loaded silicone rubber and silicone rubber control tubing are used to fabricate ECC circuits that are evaluated in a rabbit model of thrombogenicity. After 4h of blood flow, the SNAP-loaded silicone rubber circuits were able to preserve the blood platelet count at 64% of baseline (vs. 12% for silicone rubber control). A 67% reduction in the degree of thrombus formation within the thrombogenicity chamber was also observed. This study demonstrates the ability to improve the hemocompatibility of existing/commercial silicone rubber tubing via a simple solvent swelling-impregnation technique, which may also be applicable to other silicone-based blood-contacting devices. Localized nitric oxide (NO) release can be achieved from biomedical grade polymers doped with S-nitroso-N-acetylpenicillamine (SNAP). Despite the promising in vitro and in vivo biocompatibility results reported for these NO releasing polymers, many of these materials may face challenges in being translated to clinical applications, especially in the areas of polymer processing and manufacturing. In this study, we report a solvent swelling-impregnation technique to incorporate SNAP into extracorporeal circuit (ECC) tubing. These NO-releasing ECCs were able to attenuate the activation of platelets and maintain their functionality, while significantly reducing the extent of thrombus formation during 4h blood flow in the rabbit model of thrombogenicity. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Ubiquitination by the Membrane-associated RING-CH-8 (MARCH-8) Ligase Controls Steady-state Cell Surface Expression of Tumor Necrosis Factor-related Apoptosis Inducing Ligand (TRAIL) Receptor 1*

PubMed Central

van de Kooij, Bert; Verbrugge, Inge; de Vries, Evert; Gijsen, Merel; Montserrat, Veronica; Maas, Chiel; Neefjes, Jacques; Borst, Jannie

2013-01-01

The eleven members of the membrane-associated RING-CH (MARCH) ubiquitin ligase family are relatively unexplored. Upon exogenous (over)expression, a number of these ligases can affect the trafficking of membrane molecules. However, only for MARCH-1 endogenous functions have been demonstrated. For the other endogenous MARCH proteins, no functions or substrates are known. We report here that TRAIL-R1 is a physiological substrate of the endogenous MARCH-8 ligase. Human TRAIL-R1 and R2 play a role in immunosurveillance and are targets for cancer therapy, because they selectively induce apoptosis in tumor cells. We demonstrate that TRAIL-R1 is down-regulated from the cell surface, with great preference over TRAIL-R2, by exogenous expression of MARCH ligases that are implicated in endosomal trafficking, such as MARCH-1 and -8. MARCH-8 attenuated TRAIL-R1 cell surface expression and apoptosis signaling by virtue of its ligase activity. This suggested that ubiquitination of TRAIL-R1 was instrumental in its down-regulation by MARCH-8. Indeed, in cells with endogenous MARCH expression, TRAIL-R1 was ubiquitinated at steady-state, with the conserved membrane-proximal lysine 273 as one of the potential acceptor sites. This residue was also essential for the interaction of TRAIL-R1 with MARCH-1 and MARCH-8 and its down-regulation by these ligases. Gene silencing identified MARCH-8 as the endogenous ligase that ubiquitinates TRAIL-R1 and attenuates its cell surface expression. These findings reveal that endogenous MARCH-8 regulates the steady-state cell surface expression of TRAIL-R1. PMID:23300075

Methionine Deprivation Induces a Targetable Vulnerability in Triple-negative Breast Cancer Cells by Enhancing TRAIL Receptor-2 Expression

PubMed Central

Strekalova, Elena; Malin, Dmitry; Good, David M.; Cryns, Vincent L.

2015-01-01

Purpose Many neoplasms are vulnerable to methionine deficiency by mechanisms that are poorly understood. Because gene profiling studies have revealed that methionine depletion increases TNF-related apoptosis-inducing ligand receptor-2 (TRAIL-R2) mRNA, we postulated that methionine stress sensitizes breast cancer cells to proapoptotic TRAIL-R2 agonists. Experimental Design Human triple (ER/PR/HER2)-negative breast carcinoma cell lines were cultured in control or methionine-free media. The effects of methionine depletion on TRAIL receptor expression and sensitivity to chemotherapy or a humanized agonistic TRAIL-R2 monoclonal antibody (lexatumumab) were determined. The melanoma-associated antigen MAGED2 was silenced to delineate its functional role in sensitizing TNBC cells to methionine stress. An orthotopic TNBC model was utilized to evaluate the effects of dietary methionine deficiency, lexatumumab or the combination. Results Methionine depletion sensitized TNBC cells to lexatumumab-induced caspase activation and apoptosis by increasing TRAIL-R2 mRNA and cell surface expression. MCF-10A cells transformed by oncogenic H-Ras, but not untransformed cells, and matrix-detached TNBC cells were highly sensitive to the combination of lexatumumab and methionine depletion. Proteomics analyses revealed that MAGED2, which has been reported to reduce TRAIL-R2 expression, was suppressed by methionine stress. Silencing MAGED2 recapitulated features of methionine deprivation, including enhanced mRNA and cell surface expression of TRAIL receptors and increased sensitivity to TRAIL receptor agonists. Dietary methionine deprivation enhanced the antitumor effects of lexatumumab in an orthotopic metastatic TNBC model. Conclusion Methionine depletion exposes a targetable defect in TNBC cells by increasing TRAIL-R2 expression. Our findings provide the foundation for a clinical trial combining dietary methionine restriction and TRAIL-R2 agonists. PMID:25724522

Speed Control Law for Precision Terminal Area In-Trail Self Spacing

NASA Technical Reports Server (NTRS)

Abbott, Terence S.

2002-01-01

This document describes a speed control law for precision in-trail airborne self-spacing during final approach. This control law was designed to provide an operationally viable means to obtain a desired runway threshold crossing time or minimum distance, one aircraft relative to another. The control law compensates for dissimilar final approach speeds between aircraft pairs and provides guidance for a stable final approach. This algorithm has been extensively tested in Monte Carlo simulation and has been evaluated in piloted simulation, with preliminary results indicating acceptability from operational and workload standpoints.

LSRA STS Tire Test - on rim

NASA Technical Reports Server (NTRS)

1995-01-01

From 1993 to 1995, in conjunction with other NASA centers, NASA Dryden Flight Research Center, Edwards, California, used a Convair CV-990 airplane as a Landing Systems Research Aircraft (LSRA) to perform Space Shuttle tire tests. The results provided the Space Shuttle Program with data to support its flight rules and enabled it to resurface a grooved runway at Kennedy Space Center that had added unnecessary wear to the Space Shuttle tires. Tests were done using a unique fixture mounted in the center of the CV-990 fuselage, between the main landing gear. Landing gear systems from other aircraft could be attached to the test fixture, which lowered them to the runway surface during actual landings. The LSRA had the ability to reproduce the loads and speeds of the other aircraft, as well as simulate crosswind landing conditions in a safe, controlled environment. The video clip shows a landing on the concrete runway at Edwards, California on August 11, 1995, which concluded the Space Shuttle gear research program. As the Space Shuttle tire was lowered onto the surface, it was destroyed almost instantly. The rim scraped on the concrete, and stopped rolling as it became flat. It heated up and left a flaming trail of hot rubber and aluminum alloy particles. Notice how the fire quickly went out as the test gear was raised, indicating a safer condition than prevailed in a lakebed landing.

Requirement of T-lymphokine-activated killer cell-originated protein kinase for TRAIL resistance of human HeLa cervical cancer cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwon, Hyeok-Ran; Lee, Ki Won; Dong, Zigang

2010-01-01

T-lymphokine-activated killer cell-originated protein kinase (TOPK) appears to be highly expressed in various cancer cells and to play an important role in maintaining proliferation of cancer cells. However, the underlying mechanism by which TOPK regulates growth of cancer cells remains elusive. Here we report that upregulated endogenous TOPK augments resistance of cancer cells to apoptosis induced by tumor necrosis factor-related apoptosis inducing ligand (TRAIL). Stable knocking down of TOPK markedly increased TRAIL-mediated apoptosis of human HeLa cervical cancer cells, as compared with control cells. Caspase 8 or caspase 3 activities in response to TRAIL were greatly incremented in TOPK-depleted cells.more » Ablation of TOPK negatively regulated TRAIL-mediated NF-{kappa}B activity. Furthermore, expression of NF-{kappa}B-dependent genes, FLICE-inhibitory protein (FLIP), inhibitor of apoptosis protein 1 (c-IAP1), or X-linked inhibitor of apoptosis protein (XIAP) was reduced in TOPK-depleted cells. Collectively, these findings demonstrated that TOPK contributed to TRAIL resistance of cancer cells via NF-{kappa}B activity, suggesting that TOPK might be a potential molecular target for successful cancer therapy using TRAIL.« less

Respiratory and skin effects of exposure to wood dust from the rubber tree Hevea brasiliensis.

PubMed

Sripaiboonkij, P; Phanprasit, W; Jaakkola, M S

2009-07-01

Potential health effects related to wood dust from the rubber tree, which produces natural rubber latex, have not been previously investigated. The main aim of this study was to investigate the relations of rubber tree dust exposure to respiratory and skin symptoms, asthma and lung function. A cross-sectional study was conducted among 103 workers (response rate 89%) in a rubber tree furniture factory and 76 office workers (73%) in four factories in Thailand. All participants answered a questionnaire and performed spirometry. Inhalable dust levels were measured in different work areas. Factory workers showed increased risk of wheezing, nasal symptoms and asthma compared to office workers. There was a dose-dependent increase in wheeze and skin symptoms in relation to dust level. Significantly increased risks of nasal symptoms (adj OR 3.67, 95% CI 1.45 to 9.28) and asthma (8.41, 1.06 to 66.60) were detected in the low exposure category. Workers exposed to ethyl cyanoacrylate glue had significantly increased risk of cough, breathlessness and nasal symptoms. There was dose-dependent reduction in spirometric lung function with wood dust level. This study provides new evidence that workers exposed to wood dust from the rubber tree experience increased risk of nasal symptoms, wheeze, asthma and skin symptoms and have reduced spirometric lung function. Exposure to cyanoacrylate is related to significantly increased respiratory symptoms. Results suggest that the furniture industry using rubber tree wood should implement appropriate exposure control measures to reduce wood dust exposure and cyanoacrylate glue exposure to protect their employees.

Hand eczema and occupational contact allergies in healthcare workers with a focus on rubber additives.

PubMed

Hamnerius, Nils; Svedman, Cecilia; Bergendorff, Ola; Björk, Jonas; Bruze, Magnus; Engfeldt, Malin; Pontén, Ann

2018-06-20

Hand eczema (HE) in healthcare workers (HCWs) is common. Besides wet work, healthcare work also implies exposure to contact allergens. To assess HE and contact allergy related to occupational exposures in HCWs. In a cross-sectional study, 311 HCWs with HE within the preceding 12 months and a control group of 114 HCWs without HE were investigated with the baseline series and a special patch test series based on substances found in the gloves, soaps, alcoholic hand disinfectants and hand creams provided at the hospitals. Contact allergy to rubber additives was significantly more common in HCWs with HE (6%) than in HCWs without HE (1%, P = .02). The corresponding percentages for fragrances were 11% and 3%, respectively (P = .004). Occupational HE was found in 193 of 311 (62%) HCWs. Of these, 22 of 193 (11%) had occupational allergic contact dermatitis, including 17 with glove-related rubber contact allergy. Contact allergy to diphenylguanidine was as common as contact allergy to thiurams. Occupational contact allergy to rubber additives was significantly associated with sick-leave related to HE. Contact allergy to rubber additives in medical gloves is the most common cause of occupational allergic contact dermatitis in HCWs. Aimed patch testing with relevant rubber additives is mandatory when HE in HCWs is investigated. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The no-touch rubber hand paradigm and mirror-touch sensation: Support for the self-other theory of mirror-touch synesthesia.

PubMed

White, Rebekah C; Davies, Anne M Aimola

2015-01-01

We thoroughly enjoyed Ward and Banissy's Discussion Paper on mirror-touch synesthesia. The authors contrast two theories for explaining this phenomenon-the Threshold Theory and their Self-Other Theory. Ward and Banissy note that the Self-Other Theory garners support from studies that have tested individuals with mirror-touch synesthesia using the rubber hand paradigm. In this Commentary, we provide further support for the Self-Other Theory by drawing on findings from control participants without mirror-touch synesthesia tested with two different no-touch rubber hand paradigms-one paradigm makes it easier while the other makes it more difficult to make the self-other distinction.

Association between the TRAIL single nucleotide polymorphism rs1131580 and type 2 diabetes mellitus in a Han Chinese population.

PubMed

Yu, M Y; Zhao, P Q; Yan, X H; Liu, B; Zhang, Q Q; Wang, R; Ma, C H; Liang, X H; Zhu, F L; Gao, L F

2013-09-10

Tumor necrosis factor (TNF)-related apoptosis-inducing ligand (TRAIL) is expressed in different tissues and cells, including the pancreas and lymphocytes, and it can selectively induce apoptosis in tumor cells but not in most normal cells. TRAIL plays critical roles in type 1 diabetes mellitus, and is involved in type 2 diabetes mellitus (T2DM). We recently discovered the association of nonalcoholic fatty liver disease, a risk factor for T2DM, with a single nucleotide polymorphism (SNP) in the TRAIL (TNFSF10) gene at site 1595C/T (rs1131580), indicating the possible association of T2DM with this TRAIL polymorphism. The aim of this study was to investigate the relationship of the TRAIL SNP at site 1595C/T (rs1131580) with T2DM susceptibility and the biometabolic parameters of T2DM in a Han Chinese population. The polymerase chain reaction-restriction fragment length polymorphism method was used to genotype SNP rs1131580 in 292 patients with T2DM and 266 healthy controls. We found that the frequency of the CC genotype and that of the C allele of rs1131580 were significantly higher in T2DM patients than in the control group. Additionally, the triglyceride and serum creatinine levels of T2DM patients with the CC genotype were significantly higher than those of patients with the TT genotype. Thus, the CC genotype of the TRAIL SNP at 1595C/T (rs1131580) confers increased susceptible to T2DM in a Han Chinese population from Shandong Province. These data suggest that the CC genotype at this SNP is related to diabetic severity and it might be a candidate for the prognostic assessment of T2DM.

Understanding the effects of decompaction maintenance on the infill state and play performance of third-generation artificial grass pitches

PubMed Central

Forrester, Stephanie E; McLaren, Nicholas J

2015-01-01

Third generation artificial grass pitches have been observed to get harder over time. The maintenance technique of rubber infill decompaction is intended to help slow, or reverse, this process. At present, little is understood about either the science of the infill compaction process or the efficacy of decompaction maintenance. The objective of this study was to measure the changes in rubber infill net bulk density, force reduction (impact absorption) and vertical ball rebound under various levels of compactive effort in controlled laboratory-based testing. The assessments were repeated after the systems had been raked to simulate the decompaction maintenance techniques. These tests defined the limits of compaction (loose to maximally compacted) in terms of the change in rubber infill net bulk density, force reduction and vertical ball rebound. Site testing was also undertaken at four third generation pitches immediately pre and post decompaction, to determine the measurable effects in the less well controlled field environment. Rubber infill net bulk density was found to increase as compactive effort increased, resulting in increased hardness. Decompacting the surface was found to approximately fully reverse these effects. In comparison, the site measurements demonstrated similar but notably smaller magnitudes of change following the decompaction process suggesting that the field state pre and post decompaction did not reach the extremes obtained in the laboratory. The findings suggest that rubber infill net bulk density is an important parameter influencing the hardness of artificial grass and that decompactions can be an effective method to reverse compaction related hardness changes. PMID:29708108

A microbiological investigation following the disinfection of alginate and addition cured silicone rubber impression materials.

PubMed

al-Omari, W M; Jones, J C; Hart, P

1998-09-01

The antimicrobial efficacy of four commercially available disinfectants (Haz-tabs, chlorhexidine, Virkon and C&J Algisept Spray) was investigated. It was shown that all were effective in decontaminating the impressions whilst those placed only in sterile water, used as a control, showed variable levels of bacterial growth. Moreover, alginate appeared to carry significantly higher numbers of bacteria than addition cured silicone rubber.

A case-control study of bladder cancer in the United States rubber and tyre industry.

PubMed

Checkoway, H; Smith, A H; McMichael, A J; Jones, F S; Monson, R R; Tyroler, H A

1981-08-01

A case-control study of bladder cancer was conducted in five United States rubber and tyre companies to determine if there were high-risk jobs and work areas within the industry. The study included 220 male cases of bladder cancer, of whom 107 were identified from hospital record reviews and 113 from death certificates. Each case was matched individually with two industry controls by sex, race, year of birth, and company. One control was matched additionally by year of hire and duration of employment. Comparisons of cases and controls not matched by year of hire and age of hire showed no differences for those variables, which suggests that age and calendar period of first exposure to the industry were not risk determinants. When the work histories of both cases and controls were contrasted it was found that cases were more likely than controls to have worked in milling (odds ratio (OR) = 1.91) and calender operation (OR = 2.21) jobs. The relative risk estimates for milling and calender operation both exhibited linear trends of increase with duration of exposure. Milling and calender operation jobs entail potential exposures to volatilised reaction products from heated rubber stock. A better understanding of aetiological associations with job type will require more detailed characterisation of the work environment with regard to the sources and levels of aromatic amines and other suspected bladder carcinogens.

A case-control study of bladder cancer in the United States rubber and tyre industry.

PubMed Central

Checkoway, H; Smith, A H; McMichael, A J; Jones, F S; Monson, R R; Tyroler, H A

1981-01-01

A case-control study of bladder cancer was conducted in five United States rubber and tyre companies to determine if there were high-risk jobs and work areas within the industry. The study included 220 male cases of bladder cancer, of whom 107 were identified from hospital record reviews and 113 from death certificates. Each case was matched individually with two industry controls by sex, race, year of birth, and company. One control was matched additionally by year of hire and duration of employment. Comparisons of cases and controls not matched by year of hire and age of hire showed no differences for those variables, which suggests that age and calendar period of first exposure to the industry were not risk determinants. When the work histories of both cases and controls were contrasted it was found that cases were more likely than controls to have worked in milling (odds ratio (OR) = 1.91) and calender operation (OR = 2.21) jobs. The relative risk estimates for milling and calender operation both exhibited linear trends of increase with duration of exposure. Milling and calender operation jobs entail potential exposures to volatilised reaction products from heated rubber stock. A better understanding of aetiological associations with job type will require more detailed characterisation of the work environment with regard to the sources and levels of aromatic amines and other suspected bladder carcinogens. PMID:7272236

Skipping on uneven ground: trailing leg adjustments simplify control and enhance robustness.

PubMed

Müller, Roy; Andrada, Emanuel

2018-01-01

It is known that humans intentionally choose skipping in special situations, e.g. when descending stairs or when moving in environments with lower gravity than on Earth. Although those situations involve uneven locomotion, the dynamics of human skipping on uneven ground have not yet been addressed. To find the reasons that may motivate this gait, we combined experimental data on humans with numerical simulations on a bipedal spring-loaded inverted pendulum model (BSLIP). To drive the model, the following parameters were estimated from nine subjects skipping across a single drop in ground level: leg lengths at touchdown, leg stiffness of both legs, aperture angle between legs, trailing leg angle at touchdown (leg landing first after flight phase), and trailing leg retraction speed. We found that leg adjustments in humans occur mostly in the trailing leg (low to moderate leg retraction during swing phase, reduced trailing leg stiffness, and flatter trailing leg angle at lowered touchdown). When transferring these leg adjustments to the BSLIP model, the capacity of the model to cope with sudden-drop perturbations increased.

Performance of Swashplateless Ultralight Helicopter Rotor with Trailing-edge Flaps for Primary Flight Control

NASA Technical Reports Server (NTRS)

Shen, Jin-Wei; Chopra, Inderjit

2003-01-01

The objective of present study is to evaluate the rotor performance, trailing-edge deflections and actuation requirement of a helicopter rotor with trailing-edge flap system for primary flight control. The swashplateless design is implemented by modifying a two-bladed teetering rotor of an production ultralight helicopter through the use of plain flaps on the blades, and by replacing the pitch link to fixed system control system assembly with a root spring. A comprehensive rotorcraft analysis based on UMARC is carried out to obtain the results for both the swashplateless and a conventional baseline rotor configuration. The predictions show swashplateless configuration achieve superior performance than the conventional rotor attributed from reduction of parasite drag by eliminating swashplate mechanic system. It is indicated that optimal selection of blade pitch index angle, flap location, length, and chord ratio reduces flap deflections and actuation requirements, however, has virtually no effect on rotor performance.

Compliant flow designs for optimum lift control of wind turbine rotors

NASA Astrophysics Data System (ADS)

Williams, Theodore J. H.

An optimization approach was formulated to determine geometric designs that are most compliant to flow control devices. Single dielectric barrier discharge (SDBD) plasma actuators are used in the flow control design optimization as they are able to be incorporated into CFD simulations. An adjoint formulation was derived in order to have a numerically efficient way of calculating the shape derivatives on the surface of the geometric design. The design of a wind turbine blade retrofit for the JIMP 25kW wind turbine at Notre Dame is used to motivate analyses that utilize the optimization approach. The CFD simulations of the existing wind turbine blade were validated against wind tunnel testing. A one-parameter optimization was performed in order to design a trailing edge addition for the current wind turbine blade. The trailing edge addition was designed to meet a desired lift target while maximizing the lift-to-drag ratio. This analysis was performed at seven radial locations on the wind turbine blade. The new trailing edge retrofits were able to achieve the lift target for the outboard radial locations. The designed geometry has been fabricated and is currently being validated on a full-scale turbine and it is predicted to have an increase in annual energy production of 4.30%. The design of a trailing edge retrofit that includes the use of a SDBD plasma actuator was performed using a two-parameter optimization. The objective of this analysis was to meet the lift target and maximize the controllability of the design. The controllability is defined as the difference in lift between plasma on and plasma off cases. A trailing edge retrofit with the plasma actuator located on the pressure side was able to achieve the target passive lift increase while using plasma flow control to reduce the lift to below the original design. This design resulted in a highly compliant flow.

The Rubber Hand Illusion: Feeling of Ownership and Proprioceptive Drift Do Not Go Hand in Hand

PubMed Central

Rohde, Marieke; Di Luca, Massimiliano; Ernst, Marc O.

2011-01-01

In the Rubber Hand Illusion, the feeling of ownership of a rubber hand displaced from a participant's real occluded hand is evoked by synchronously stroking both hands with paintbrushes. A change of perceived finger location towards the rubber hand (proprioceptive drift) has been reported to correlate with this illusion. To measure the time course of proprioceptive drift during the Rubber Hand Illusion, we regularly interrupted stroking (performed by robot arms) to measure perceived finger location. Measurements were made by projecting a probe dot into the field of view (using a semi-transparent mirror) and asking participants if the dot is to the left or to the right of their invisible hand (Experiment 1) or to adjust the position of the dot to that of their invisible hand (Experiment 2). We varied both the measurement frequency (every 10 s, 40 s, 120 s) and the mode of stroking (synchronous, asynchronous, just vision). Surprisingly, with frequent measurements, proprioceptive drift occurs not only in the synchronous stroking condition but also in the two control conditions (asynchronous stroking, just vision). Proprioceptive drift in the synchronous stroking condition is never higher than in the just vision condition. Only continuous exposure to asynchronous stroking prevents proprioceptive drift and thus replicates the differences in drift reported in the literature. By contrast, complementary subjective ratings (questionnaire) show that the feeling of ownership requires synchronous stroking and is not present in the asynchronous stroking condition. Thus, subjective ratings and drift are dissociated. We conclude that different mechanisms of multisensory integration are responsible for proprioceptive drift and the feeling of ownership. Proprioceptive drift relies on visuoproprioceptive integration alone, a process that is inhibited by asynchronous stroking, the most common control condition in Rubber Hand Illusion experiments. This dissociation implies that conclusions about feelings of ownership cannot be drawn from measuring proprioceptive drift alone. PMID:21738756

30 CFR 28.21 - Certificates of approval; contents.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Approval and Disapproval § 28.21 Certificates of approval... protection for trailing cables. (c) Each certificate of approval shall be accompanied by a reproduction of... certificate of approval shall also contain the approved quality control plan as specified in § 28.31. ...

30 CFR 28.21 - Certificates of approval; contents.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Approval and Disapproval § 28.21 Certificates of approval... protection for trailing cables. (c) Each certificate of approval shall be accompanied by a reproduction of... certificate of approval shall also contain the approved quality control plan as specified in § 28.31. ...

30 CFR 28.21 - Certificates of approval; contents.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Approval and Disapproval § 28.21 Certificates of approval... protection for trailing cables. (c) Each certificate of approval shall be accompanied by a reproduction of... certificate of approval shall also contain the approved quality control plan as specified in § 28.31. ...

30 CFR 28.21 - Certificates of approval; contents.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION FOR TRAILING CABLES IN COAL MINES Approval and Disapproval § 28.21 Certificates of approval... protection for trailing cables. (c) Each certificate of approval shall be accompanied by a reproduction of... certificate of approval shall also contain the approved quality control plan as specified in § 28.31. ...

Pheromone disruption of Argentine ant trail integrity.

PubMed

Suckling, D M; Peck, R W; Manning, L M; Stringer, L D; Cappadonna, J; El-Sayed, A M

2008-12-01

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m(2)) to 1- and 4-m(2) plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected.

Pheromone disruption of Argentine ant trail integrity

USGS Publications Warehouse

Suckling, D.M.; Peck, R.W.; Manning, L.M.; Stringer, L.D.; Cappadonna, J.; El-Sayed, A. M.

2008-01-01

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m2) to 1- and 4-m2 plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. ?? 2008 Springer Science+Business Media, LLC.

Suppression of flutter

NASA Technical Reports Server (NTRS)

Nissim, E. (Inventor)

1973-01-01

An active aerodynamic control system to control flutter over a large range of oscillatory frequencies is described. The system is not affected by mass, stiffness, elastic axis, or center of gravity location of the system, mode of vibration, or Mach number. The system consists of one or more pairs of leading edge and trailing edge hinged or deformable control surfaces, each pair operated in concert by a stability augmentation system. Torsion and bending motions are sensed and converted by the stability augmentation system into leading and trailing edge control surface deflections which produce lift forces and pitching moments to suppress flutter.

Soil nitrogen oxide fluxes from lowland forests converted to smallholder rubber and oil palm plantations in Sumatra, Indonesia

NASA Astrophysics Data System (ADS)

Hassler, Evelyn; Corre, Marife D.; Kurniawan, Syahrul; Veldkamp, Edzo

2017-06-01

Oil palm (Elaeis guineensis) and rubber (Hevea brasiliensis) plantations cover large areas of former rainforest in Sumatra, Indonesia, supplying the global demand for these crops. Although forest conversion is known to influence soil nitrous oxide (N2O) and nitric oxide (NO) fluxes, measurements from oil palm and rubber plantations are scarce (for N2O) or nonexistent (for NO). Our study aimed to (1) quantify changes in soil-atmosphere fluxes of N oxides with forest conversion to rubber and oil palm plantations and (2) determine their controlling factors. In Jambi, Sumatra, we selected two landscapes that mainly differed in texture but were both on heavily weathered soils: loam and clay Acrisol soils. Within each landscape, we investigated lowland forests, rubber trees interspersed in secondary forest (termed as jungle rubber), both as reference land uses and smallholder rubber and oil palm plantations as converted land uses. In the loam Acrisol landscape, we conducted a follow-on study in a large-scale oil palm plantation (called PTPN VI) for comparison of soil N2O fluxes with smallholder oil palm plantations. Land-use conversion to smallholder plantations had no effect on soil N-oxide fluxes (P = 0. 58 to 0.76) due to the generally low soil N availability in the reference land uses that further decreased with land-use conversion. Soil N2O fluxes from the large-scale oil palm plantation did not differ with those from smallholder plantations (P = 0. 15). Over 1-year measurements, the temporal patterns of soil N-oxide fluxes were influenced by soil mineral N and water contents. Across landscapes, annual soil N2O emissions were controlled by gross nitrification and sand content, which also suggest the influence of soil N and water availability. Soil N2O fluxes (µg N m-2 h-1) were 7 ± 2 to 14 ± 7 (reference land uses), 6 ± 3 to 9 ± 2 (rubber), 12 ± 3 to 12 ± 6 (smallholder oil palm) and 42 ± 24 (large-scale oil palm). Soil NO fluxes (µg N m-2 h-1) were -0.6 ± 0.7 to 5.7 ± 5.8 (reference land uses), -1.2 ± 0.5 to -1.0 ± 0.2 (rubber) and -0.2 ± 1.2 to 0.7 ± 0.7 (smallholder oil palm). To improve the estimate of soil N-oxide fluxes from oil palm plantations in this region, studies should focus on large-scale plantations (which usually have 2 to 4 times higher N fertilization rates than smallholders) with frequent measurements following fertilizer application.

Influence of Rubber Size on Properties of Crumb Rubber Mortars

PubMed Central

Yu, Yong; Zhu, Han

2016-01-01

Studies on the properties and applications of rubber cement-based materials are well documented. The sizes of rubbers used in these materials varied. However, information about the effects of rubber size on the properties of rubber cement-based materials, especially pore structure, mechanical strengths, and drying shrinkage properties, remains limited. Three groups of rubber with major particle sizes of 2–4 mm, 1–3 mm, and 0–2 mm were selected in this study. This paper presents experimental studies on the effects of rubber size on the consistency, fresh density, pore structure, mechanical properties, and drying shrinkage properties of crumb rubber mortars (CRMs). Results demonstrated that the consistency and fresh density of CRMs decreased with the rubber size. As to the pore structure, the total pore volume increased with the decrease of the rubber size. By contrast, the influence of the rubber size on the mesopore (<50 nm) volume is not as significant as that of the rubber content. The mechanical properties of CRMs decreased with the rubber size. Low rubber stiffness and large pore volumes, especially those of small sized rubbers, contribute to the reduction of CRMs strength. The drying shrinkage of CRM increases as the rubber size decreases. The influences of rubber size on capillary tension are not significant. Thus, the shrinkage increases with the decrease of rubber size mainly because of its function in the deformation modulus reduction of CRMs. PMID:28773649

Down-Regulation of Small Rubber Particle Protein Expression Affects Integrity of Rubber Particles and Rubber Content in Taraxacum brevicorniculatum

PubMed Central

Hillebrand, Andrea; Post, Janina J.; Wurbs, David; Wahler, Daniela; Lenders, Malte; Krzyzanek, Vladislav; Prüfer, Dirk; Gronover, Christian Schulze

2012-01-01

The biosynthesis of rubber is thought to take place on the surface of rubber particles in laticifers, highly specialized cells that are present in more than 40 plant families. The small rubber particle protein (SRPP) has been supposed to be involved in rubber biosynthesis, and recently five SRPPs (TbSRPP1–5) were identified in the rubber-producing dandelion species Taraxacum brevicorniculatum. Here, we demonstrate by immunogold labeling that TbSRPPs are localized to rubber particles, and that rubber particles mainly consist of TbSRPP3, 4 and 5 as shown by high-resolution two-dimensional gel electrophoresis and mass spectrometric analysis. We also carried out an RNA-interference approach in transgenic plants to address the function of TbSRPPs in rubber biosynthesis as well as rubber particle morphology and stability. TbSRPP-RNAi transgenic T. brevicorniculatum plants showed a 40–50% reduction in the dry rubber content, but neither the rubber weight average molecular mass nor the polydispersity of the rubber were affected. Although no phenotypical differences to wild-type particles could be observed in vivo, rubber particles from the TbSRPP-RNAi transgenic lines were less stable and tend to rapidly aggregate in expelling latex after wounding of laticifers. Our results prove that TbSRPPs are very crucial for rubber production in T. brevicorniculatum, probably by contributing to a most favourable and stable rubber particle architecture for efficient rubber biosynthesis and eventually storage. PMID:22911861

Systematic review of the evidence for Trails B cut-off scores in assessing fitness-to-drive.

PubMed

Roy, Mononita; Molnar, Frank

2013-01-01

Fitness-to-drive guidelines recommend employing the Trail Making B Test (a.k.a. Trails B), but do not provide guidance regarding cut-off scores. There is ongoing debate regarding the optimal cut-off score on the Trails B test. The objective of this study was to address this controversy by systematically reviewing the evidence for specific Trails B cut-off scores (e.g., cut-offs in both time to completion and number of errors) with respect to fitness-to-drive. Systematic review of all prospective cohort, retrospective cohort, case-control, correlation, and cross-sectional studies reporting the ability of the Trails B to predict driving safety that were published in English-language, peer-reviewed journals. Forty-seven articles were reviewed. None of the articles justified sample sizes via formal calculations. Cut-off scores reported based on research include: 90 seconds, 133 seconds, 147 seconds, 180 seconds, and < 3 errors. There is support for the previously published Trails B cut-offs of 3 minutes or 3 errors (the '3 or 3 rule'). Major methodological limitations of this body of research were uncovered including (1) lack of justification of sample size leaving studies open to Type II error (i.e., false negative findings), and (2) excessive focus on associations rather than clinically useful cut-off scores.

The Relative Contribution of Ankle Moment and Trailing Limb Angle to Propulsive Force during Gait

PubMed Central

Hsiao, HaoYuan; Knarr, Brian A.; Higginson, Jill S.; Binder-Macleod, Stuart A.

2014-01-01

A major factor for increasing walking speed is the ability to increase propulsive force. Although propulsive force has been shown to be related to ankle moment and trailing limb angle, the relative contribution of each factor to propulsive force has never been determined. The primary purpose of this study was to quantify the relative contribution of ankle moment and trailing limb angle to propulsive force for able-bodied individuals walking at different speeds. Twenty able-bodied individuals walked at their self-selected and 120% of self-selected walking speed on the treadmill. Kinematic data were collected using an 8-camera motion-capture system. A model describing the relationship between ankle moment, trailing limb angle and propulsive force was obtained through quasi-static analysis. Our main findings were that ankle moment and trailing limb angle each contributes linearly to propulsive force, and that the change in trailing limb angle contributes almost as twice as much as the change in ankle moment to the increase in propulsive force during speed modulation for able-bodied individuals. Able-bodied individuals preferentially modulate trailing limb angle more than ankle moment to increase propulsive force. Future work will determine if this control strategy can be applied to individuals poststroke. PMID:25498289

Risk of exposure to potential vector mosquitoes for rural workers in Northern Lao PDR

PubMed Central

Thammavong, Phoutmany; Lindsay, Steve W.; Brey, Paul T.

2017-01-01

Background One major consequence of economic development in South-East Asia has been a rapid expansion of rubber plantations, in which outbreaks of dengue and malaria have occurred. Here we explored the difference in risk of exposure to potential dengue, Japanese encephalitis (JE), and malaria vectors between rubber workers and those engaged in traditional forest activities in northern Laos PDR. Methodology/Principal findings Adult mosquitoes were collected for nine months in secondary forests, mature and immature rubber plantations, and villages. Human behavior data were collected using rapid participatory rural appraisals and surveys. Exposure risk was assessed by combining vector and human behavior and calculating the basic reproduction number (R0) in different typologies. Compared to those that stayed in the village, the risk of dengue vector exposure was higher for those that visited the secondary forests during the day (odds ratio (OR) 36.0), for those living and working in rubber plantations (OR 16.2) and for those that tapped rubber (OR 3.2). Exposure to JE vectors was also higher in the forest (OR 1.4) and, similar when working (OR 1.0) and living in the plantations (OR 0.8). Exposure to malaria vectors was greater in the forest (OR 1.3), similar when working in the plantations (OR 0.9) and lower when living in the plantations (OR 0.6). R0 for dengue was >2.8 for all habitats surveyed, except villages where R0≤0.06. The main malaria vector in all habitats was Anopheles maculatus s.l. in the rainy season and An. minimus s.l. in the dry season. Conclusions/Significance The highest risk of exposure to vector mosquitoes occurred when people visit natural forests. However, since rubber workers spend long periods in the rubber plantations, their risk of exposure is increased greatly compared to those who temporarily enter natural forests or remain in the village. This study highlights the necessity of broadening mosquito control to include rubber plantations. PMID:28742854

Sensitization to Rubber Accelerators in Northeastern Italy: The Triveneto Patch Test Database.

PubMed

Buttazzo, Silvia; Prodi, Andrea; Fortina, Anna Belloni; Corradin, Maria Teresa; Larese Filon, Francesca

2016-01-01

Natural and synthetic rubbers containing rubber accelerators are well-known causes of occupational skin disease. Allergic contact dermatitis caused by rubber gloves is frequent and has almost exclusively been attributed to contact sensitization to accelerators. This study aimed to evaluate the frequency of rubber accelerators sensitization in the population living in northeastern Italy, to find time trend and a correlation with occupations, and to investigate co-sensitization between rubber accelerators. A population of 23,774 subjects was patch tested in 6 cities in northeastern Italy in the years 1996 to 2012 using carba mix 3%, thiuram mix 1%, benzothiazole (MBT) mix 1%, and isopropyl phenyl paraphenylamine diamine (IPPD) mix 0.6%. The overall frequency of carbamates, MBT, thiurams, and IPPD mix sensitization was 3.4%, 0.65%, 1.75%, and 0.83%, respectively. On a logistic regression analysis (control group: white-collar workers), we found a statistically significant association to carbamates (odds ratio [OR], 1.3; 95% confidence interval [CI], 1.03-1.7) and thiurams (OR, 1.6; 95% CI, 1.1-2.3) for health care workers. Thiuram sensitivity was also significantly associated with dermatitis in maids and restaurant workers (OR, 2.2; 95% CI, 1.4-3.6), hairdressers (OR, 3.6; 95% CI, 1.8-7.1), shop assistants (OR, 2.9; 95% CI, 1.2-6.8), construction workers (OR, 2.7; 95% CI, 1.7-4.1), mechanics (OR, 2.1; 95% CI, 1.3-3.4), and professional drivers (OR, 2.6; 95% CI, 1.2-5.9). In conclusion, our results demonstrated that rubber accelerators have an important role in allergic contact dermatitis in the northeast of Italy and their sensitization is associated significantly with occupations that wear gloves or use chemical substances. Between rubber accelerators tested, carbamates sensitization is prevalent and increasing during considered years.

Causes and Control of Corrosion in Buried-Conduit Heat Distribution Systems

DTIC Science & Technology

1991-07-01

rubber , and foamed plastics such as polyurethanic anld phenolic) nominally contain 10 to 500 ppmn soluble chloide.’ Further, insulation can also become...pressure ratings. A maximum P X T limitation exists for all gasket materials. For example, the maximum temperature and pressure ratings for an EPDM ...ethylene propylene diene monomer) rubber material are, respectively, 3() ’F and 150 psi. The material, however, cannot be expected to perform

Recent achievements and research initiated in the Swedish plastics and rubber industry.

PubMed Central

Englund, A; Holmberg, B

1976-01-01

The improvement in exposure conditions in the Swedish vinyl chloride producing industry is reported. The article comments on the technology and control methods by which the vinyl chloride concentration has been lowered to less than 1 ppm vinyl chloride. Two epidemiological retrospective cohort studies are presently under way on workers in PVC-utilizing industries and in the rubber industry. Images FIGURE 1. FIGURE 2. FIGURE 3. PMID:1026411

Reusable Material for Drop Tower

DTIC Science & Technology

2011-08-01

R3 Buna-N Rubber ............................................................................................... 32 B-3. R5 EPDM Rubber ...Butyl Rubber . Figure B-2. R3 Buna-N Rubber . Figure B-3. R5 EPDM Rubber . Figure B-4. R6 Gel Rubber . UNCLASSIFIED 33...11 Current Drop Tower Material & Setup .......................................................... 11 Bowling Ball Rubber Material Sample Test

Effects of tumor necrosis factor-related apoptosis-inducing ligand alone and in combination with chemotherapeutic agents on patients' colon tumors grown in SCID mice.

PubMed

Naka, Takuji; Sugamura, Kenji; Hylander, Bonnie L; Widmer, Michael B; Rustum, Youcef M; Repasky, Elizabeth A

2002-10-15

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) has been reported to induce apoptosis in a variety of malignant cell lines, but it shows little or no toxicity in most normal cells. We examined the response of three human colon tumors to TRAIL alone and in combination with chemotherapy, using SCID mice engrafted with intact patient surgical specimens. These tumors, taken from fresh surgical specimens, contained the heterogeneous tumor cell population characteristic of patient tumors and showed differential sensitivity to TRAIL alone. We also investigated the effect of TRAIL in combination with chemotherapy, using one tumor that showed moderate sensitivity to TRAIL alone. Combining TRAIL with either 5-fluorouracil (5-FU) or CPT-11 (irinotecan hydrochloride) produced a greatly enhanced antitumor effect over that of either agent alone, with 50% of the animals achieving complete tumor regression with a combination of TRAIL and CPT-11. By histological analysis, tumors treated with TRAIL plus either 5-FU or CPT-11 were seen to consist mainly of connective tissue and fibrotic areas with only a few scattered tumor cells encapsulated in the connective tissue. Several markers were assessed to investigate the basis for the observed therapeutic effect, and significant induction of apoptosis was observed in tumors treated with curative combinations. Cytoplasmic and cell surface expression of the TRAIL receptors DR4 and DR5 was observed in this patient's tumor by immunohistochemistry. Tumors treated with CPT-11 showed increased membrane expression of DR5, suggesting that CPT-11 may increase sensitivity to TRAIL by up-regulation of DR5. These results obtained in a relevant preclinical model support the idea that the use of TRAIL in combination with either 5-FU or CPT-11 may be an effective strategy in controlling human colon cancer.

Methionine Deprivation Induces a Targetable Vulnerability in Triple-Negative Breast Cancer Cells by Enhancing TRAIL Receptor-2 Expression.

PubMed

Strekalova, Elena; Malin, Dmitry; Good, David M; Cryns, Vincent L

2015-06-15

Many neoplasms are vulnerable to methionine deficiency by mechanisms that are poorly understood. Because gene profiling studies have revealed that methionine depletion increases TNF-related apoptosis-inducing ligand receptor-2 (TRAIL-R2) mRNA, we postulated that methionine stress sensitizes breast cancer cells to proapoptotic TRAIL-R2 agonists. Human triple (ER/PR/HER2)-negative breast carcinoma cell lines were cultured in control or methionine-free media. The effects of methionine depletion on TRAIL receptor expression and sensitivity to chemotherapy or a humanized agonistic TRAIL-R2 monoclonal antibody (lexatumumab) were determined. The melanoma-associated antigen MAGED2 was silenced to delineate its functional role in sensitizing TNBC cells to methionine stress. An orthotopic TNBC model was utilized to evaluate the effects of dietary methionine deficiency, lexatumumab, or the combination. Methionine depletion sensitized TNBC cells to lexatumumab-induced caspase activation and apoptosis by increasing TRAIL-R2 mRNA and cell surface expression. MCF-10A cells transformed by oncogenic H-Ras, but not untransformed cells, and matrix-detached TNBC cells were highly sensitive to the combination of lexatumumab and methionine depletion. Proteomics analyses revealed that MAGED2, which has been reported to reduce TRAIL-R2 expression, was suppressed by methionine stress. Silencing MAGED2 recapitulated features of methionine deprivation, including enhanced mRNA and cell surface expression of TRAIL receptors and increased sensitivity to TRAIL receptor agonists. Dietary methionine deprivation enhanced the antitumor effects of lexatumumab in an orthotopic metastatic TNBC model. Methionine depletion exposes a targetable defect in TNBC cells by increasing TRAIL-R2 expression. Our findings provide the foundation for a clinical trial combining dietary methionine restriction and TRAIL-R2 agonists. Clin Cancer Res; 21(12); 2780-91. ©2015 AACR. ©2015 American Association for Cancer Research.

Multifunctionalized polyethyleneimine-based nanocarriers for gene and chemotherapeutic drug combination therapy through one-step assembly strategy

PubMed Central

Wang, Tianqi; Zhang, Bo; Liu, Chunxi; Zhang, Na

2017-01-01

Gene therapy combined with chemotherapy to achieve synergistic therapeutic effects has been a hot topic in recent years. In this project, the human tumor necrosis factor-related apoptosis-inducing ligand-encoding plasmid gene (TRAIL) and doxorubicin (Dox)-coloaded multi-functional nanocarrier was constructed based on the theory of circulation, accumulation, internalization, and release. Briefly, polyethyleneimine (PEI) was selected as skeleton material to synthesize PEI–polyethylene glycol (PEG)–TAT (PPT). Dox was conjugated to PEI using C6-succinimidyl 6-hydrazinonicotinate acetone hydrazone (C6-SANH), and a pH-sensitive Dox-PEI (DP) conjugate was obtained. Then, intracellular cationic pH-sensitive cellular assistant PPT and DP were mixed to condense TRAIL, and TRAIL–Dox coloaded PPT/DP/TRAIL (PDT) nanocarriers were obtained by one-step assembly. TRAIL was completely condensed by DP or PPT when mass ratios (DP/PPT to TRAIL) were up to 100:64, which indicated that DP and PPT could be mixed at any ratio for TRAIL condensation. The intracellular uptake rate of PDT was enhanced (P<0.05) when the contents of PPT in PPT+DP increased from 0 to 30%. Free Dox and TRAIL-loaded nanocarriers (PPT/C6-SANH-PEI/TRAIL [PCT]) were selected as controls to verify the synergistic antitumor effects of PDT. Compared with free TRAIL, TRAIL-protein expression was upregulated by PDT and PCT on Western blotting assays. The in vitro cytotoxicity of PDT was significantly enhanced compared to free Dox and PCT (P<0.01). Furthermore, murine PDT nanocarriers showed higher in vivo antitumor ability than both the Dox group (P<0.05) and the murine PCT group (P<0.05). These results indicated that the TRAIL + Dox synergistic antitumor effect could be achieved by PDT, which paves the way to gene–drug combination therapy for cancer. PMID:29263663

Toxic effects of butyl elastomers on aerobic methane oxidation

NASA Astrophysics Data System (ADS)

Niemann, Helge; Steinle, Lea I.; Blees, Jan H.; Krause, Stefan; Bussmann, Ingeborg; Lehmann, Moritz F.; Treude, Tina

2013-04-01

Large quantities of the potent greenhouse gas methane are liberated into the water column of marine and lacustrine environments where it may be consumed by aerobic methane oxidising bacteria before reaching the atmosphere.The reliable quantification of aerobic methane oxidation (MOx) rates is consequently of paramount importance for estimating methane budgets and to understand the controls on water column methane cycling. A widely used set of methods for measuring MOx rates is based on the incubation of water samples during which the consumption of methane is monitored, for instance with radio-tracer assays. Typically, incubation vessels are sealed with butyl rubber stoppers because these elastomers are essentially impermeable for gases at the relevant time scales. We tested the effect of different stopper materials (unmodified- and halogenated butyl rubber) on MOx activity in environmental samples and in cultures of methane oxidising bacteria. MOx rates in samples sealed with unmodified butyl rubber were > 75% lower compared to parallel incubations with halogenated butyl rubber seals, suggesting inhibiting/toxic effects associated with the use of unmodified butyl elastomers. To further explore the cause of these effects, we analysed aqueous extracts of the different stoppers. Halogenated butyl rubber stoppers appeared to bleed off comparably little amounts of organics. In stark contrast, extracts of unmodified butyl rubber were contaminated with various organic compounds including potential bactericides such as benzyltoluenes, phenylalkanes and benzuothiazoles. We also found tetramethylthiourea, a scavenger of active oxygen species, which may inhibit the MOx pathway.

Thermoplastic vulcanizate nanocomposites based on polypropylene/ethylene propylene diene terpolymer (PP/EPDM) prepared by reactive extrusion

NASA Astrophysics Data System (ADS)

Mirzadeh, Amin

For this work, different grades of polypropylene-g-maleic anhydride polymers were chosen to elucidate the effect of compatibilizer on the nanoclay dispersion level in thermoplastic phase. X-ray diffraction (XRD) patterns along with transmission electron microscopy (TEM) and scanning electron microscope (SEM) micrographs confirmed that prepared PP nanocomposites ranged from intercalated structure to a coexistence of intercalated tactoids and exfoliated layers namely “partially exfoliated” nanocomposite. Among various factors affecting the compatibilizer performance, it is shown that only the relaxation behaviour of compatibilizer correlates directly with the nanocomposites characterization results; higher relaxation times of the compatibilizer are associated with better dispersion of nanoclay. To study the co-continuity development of the nonreactive blends, EPDM and the mentioned PP nanocomposites at various compositions were melt blended using an internal mixer. Based on continuity measurements of TPEs and TPE nanocomposites for both thermoplastic and rubber phase, it is shown that the presence of nanoclay decreases the co-continuity composition range and alters its symmetrical feature. However, this effect is more pronounced in the intercalated nanocomposites than in partially exfoliated nanocomposites. It seems that better nanoclay dispersion limits the reduction of the thermoplastic phase continuity in a manner that the continuity index of the thermoplastic phase for partially exfoliated TPE nanocomposite prepared at high EPDM content (i.e. at 70 wt%) is greater than that of corresponding TPE without nanoclay. According to these results, it is possible to shift to higher EPDM content using partially exfoliated system before formation of matrix-dispersed particle structure which limits thermoplastic vulcanizate production. This should be mentioned that gamma irradiation was carried out in order to fix the EPDM morphology to estimate the continuity of PP using the solvent extraction and gravimetry technique. Additionally, the effect of continuity on rheological behaviour of TPE nanocomposites was investigated. The ultimate goal in this field is to maximize the rubber like behaviour by controlling the blend morphology and the level of crosslinking. Therefore, this study also covers the effects of nanoclay presence and its dispersion level on the crosslinking reaction of thermoplastic vulcanizate nanocomposites prepared by reactive extrusion. Here, the rubber phase was dynamically vulcanized using dimethylol phenolic resin or octylphenol-formaldehyde resin along with stannous chloride dihydrate as the catalyst. In the present study, the dynamic vulcanization of the prepared TPVs and corresponding nanocomposites are characterized using different criteria, such as gel content, viscosity and normalized storage modulus in the time sweep tests, nuclear magnetic resonance (NMR) signal line width, bound curative content and residual diene concentration. The combination of the above parameters appears to be sufficient to provide a clear description of the systems. The last part of the present study is devoted to find how the dispersion level of nanoclay and consequently the extent of crosslinking change the rubber like behaviour and the morphology of the prepared TPVs. Therefore, recently developed method named temperature scanning stress relaxation (TSSR) was used to estimate the rubber indices of TPVs and TPV nanocomposites. The mentioned method also successfully provided information about the extent of crosslinking reaction. It is shown that the rubber like behaviour of the blends containing 50wt% and 60wt% of EPDM in which morphological studies suggest the presence of the rubber droplets in vicinity of irregular shape rubber particles with a low level of interconnectivity, correlates with the rubber droplet size. Therefore, the nanoclay presence affects the rubber index values mainly through its effect on the size of the rubber droplets that controls the number of retraction points in the proposed buckling mechanism during the TSSR test. It should be mentioned that by increasing the EPDM content, the number of the droplet like domains decreases and more irregular shape rubber particles is formed. On the other hand, the direct relation between rubber index values and the crosslink density is observed only for those series of TPVs showing the fully developed extensive network between irregular shape rubber domains (blends containing 70wt% of EPDM). Hence, the nanoclay dispersion level influences the rubber like behaviour through its effect on the crosslink density. (Abstract shortened by UMI.).

Smart vibration control analysis of seismic response using MR dampers in the elevated highway bridge structures

NASA Astrophysics Data System (ADS)

Yan, Shi; Zhang, Hai

2005-05-01

The magnetorheological (MR) damper is on of the smart controllers used widely in civil engineering structures. These kinds of dampers are applied in the paper in the elevated highway bridge (EHB) with rubber bearing support piers to mitigate damages of the bridge during the severe earthquake ground motion. The dynamic calculating model and equation of motion for the EHB system are set up theoretically and the LQR semi-active control algorithm of seismic response for the EHB system is developed to reduce effectively the responses of the structure. The non-linear calculation model of the piers that rigid degradation is considered and numerical simulative calculation are carried out by Matlab program. The number and location as well as the maximum control forces of the MR dampers, which are the most important parameters for the controlled system, are determined and the rubber bearing and connection forms of the damper play also important rule in the control efficiency. A real EHB structure that is located in Anshan city, Liaoning province in China is used as an example to be calculated under different earthquake records. The results of the calculation show that it is effective to reduce seismic responses of the EHB system by combining the rubber bearing isolation with semi-active MR control technique under the earthquake ground motion. The locations of MR dampers and structural parameters will influence seriously to the effects of structural vibration control.

Environmental Assessment. Proposed Sahara Mustard Control on the Barry M. Goldwater Range - East

DTIC Science & Technology

2012-02-01

While some sites consist of only a few artifacts or a single archaeological feature such as a trail or a hearth ; others cover a large area and...such as hearths , roasting pits, and fire-affected rock, cleared areas or sleeping circles, linear and circular rock alignments, rock cairns, trails

77 FR 23305 - Self-Regulatory Organizations; New York Stock Exchange LLC; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-18

... Organizations Report to the Order Audit Trail System Information Barriers Put Into Place by the Member... Rule 5320 to require that member organizations report to the Order Audit Trail System (``OATS... implements and uses an effective system of internal controls--such as appropriate information barriers--that...

Soil response to skidder trafficking and slash application

Treesearch

Brian M. Parkhurst; W. Michael Aust; M. Chad Bolding; Scott M. Barrett; Emily A. Carter

2018-01-01

Ground-based timber harvesting systems are common in the United States. Harvesting machinery can negatively influence soils by increasing erosion and decreasing site productivity. Skid trails can become compacted and erosive. Slash applications to skid trails are effective for erosion control, yet few investigations have examined effects of slash on soil physical...

Degradation of blending vulcanized natural rubber and nitril rubber (NR/NBR) by dimethyl ether through variation of elastomer ratio

NASA Astrophysics Data System (ADS)

Saputra, A. H.; Juneva, S.; Sari, T. I.; Cifriadi, A.

2018-04-01

Dimethyl ether can cause degradation of the rubber material seal in some applications. In order to use of natural rubber in industry, research about a blending of natural rubber (NR) and nitrile rubber (NBR) to produce rubber to meet the standard seal material application were conducted. This study will observe the degradation mechanisms that occur in the blending natural rubber and nitrile rubber (NR/NBR) by dimethyl ether. Nitrile rubber types used in this study is medium quality nitrile rubber with 33% of acrylonitrile content (NBR33). The observed parameters are percent change in mass, mechanical properties and surface morphology. This study is limited to see the effect of variation vulcanized blending ratio (NR/NBR33) against to swelling. The increase of nitrile rubber (NBR33) ratio of blending rubber vulcanized can reduce the tensile strength and elongation. The best elastomer variation was obtained after comparing with the standard feasibility material of seal is rubber vulcanized blending (NR/NBR33) with ratio 40:60 NR: NBR.

Rubber industry

NASA Astrophysics Data System (ADS)

Staszak, Maciej

2018-03-01

Following chapter presents short introductory description of rubber and rubber industry. The main problem of rubber industry is the way of the usage of spent tires. Furthermore very important group of problems arise considering the metal and nonmetal additives which are significant component of the vulcanized rubber. The key attention is dedicated to typical ways of rubber usage in utilization and recovery of metals from spent rubber materials concentrating specifically on used tires processing. The method of recovery of rare metals from rubber tires was described. The rubber debris finds widest use in the field of waste metal solutions processing. The environmental pollution caused by metals poses serious threat to humans. Several applications of the use of waste rubber debris to remove metals from environmental waters were described. Moreover, the agriculture usage of waste tire rubber debris is described, presenting systems where the rubber material can be useful as a soil replacement.

Rats track odour trails accurately using a multi-layered strategy with near-optimal sampling.

PubMed

Khan, Adil Ghani; Sarangi, Manaswini; Bhalla, Upinder Singh

2012-02-28

Tracking odour trails is a crucial behaviour for many animals, often leading to food, mates or away from danger. It is an excellent example of active sampling, where the animal itself controls how to sense the environment. Here we show that rats can track odour trails accurately with near-optimal sampling. We trained rats to follow odour trails drawn on paper spooled through a treadmill. By recording local field potentials (LFPs) from the olfactory bulb, and sniffing rates, we find that sniffing but not LFPs differ between tracking and non-tracking conditions. Rats can track odours within ~1 cm, and this accuracy is degraded when one nostril is closed. Moreover, they show path prediction on encountering a fork, wide 'casting' sweeps on encountering a gap and detection of reappearance of the trail in 1-2 sniffs. We suggest that rats use a multi-layered strategy, and achieve efficient sampling and high accuracy in this complex task.

Helicopter rotor trailing edge noise. [noise prediction

NASA Technical Reports Server (NTRS)

Schlinker, R. H.; Amier, R. K.

1981-01-01

A two dimensional section of a helicopter main rotor blade was tested in an acoustic wind tunnel at close to full-scale Reynolds numbers to obtain boundary layer data and acoustic data for use in developing an acoustic scaling law and testing a first principles trailing edge noise theory. Results were extended to the rotating frame coordinate system to develop a helicopter rotor trailing edge noise prediction. Comparisons of the calculated noise levels with helicopter flyover spectra demonstrate that trailing edge noise contributes significantly to the total helicopter noise spectrum at high frequencies. This noise mechanism is expected to control the minimum rotor noise. In the case of noise radiation from a local blade segment, the acoustic directivity pattern is predicted by the first principles trailing edge noise theory. Acoustic spectra are predicted by a scaling law which includes Mach number, boundary layer thickness and observer position. Spectrum shape and sound pressure level are also predicted by the first principles theory but the analysis does not predict the Strouhal value identifying the spectrum peak.

South American Leaf Blight of the Rubber Tree (Hevea spp.): New Steps in Plant Domestication using Physiological Features and Molecular Markers

PubMed Central

Lieberei, Reinhard

2007-01-01

Background Rubber trees (Hevea spp.) are perennial crops of Amazonian origin that have been spread over the whole tropical belt to guarantee worldwide production of natural rubber. This crop plant has found its place in many national economies of producing countries, and although its domestication by selection of suitable genotypes was very slow, it contributes a lot to the welfare of small farmers worldwide. Its development is limited by severe diseases. In South America, the main fungal disease of rubber trees is the South American leaf blight (SALB) caused by the ascomycete Microcyclus ulei. This fungus inhibits natural rubber production on a commercial scale in South and Central America. Scope The disease is still restricted to its continent of origin, but its potential to be distributed around the world rises with every transcontinental airline connection that directly links tropical regions. The need to develop control measures against the disease is an urgent task and must be carried out on an international scale. All control efforts so far taken since 1910 have ended in a miserable failure. Even the use of modern systemic fungicides and use of greatly improved application techniques have failed to prevent large losses and dieback of trees. The results of research dealing with both the disease and the pathosystem over more than 50 years are summarized and placed into perspective. Future Prospects A detailed knowledge of this host–pathogen combination requires understanding of the dynamics of Hevea leaf development, the biochemical potential for cyanide liberation, and molecular data for several types of resistance factors. Resolution of the Hevea–SALB problem may serve as a model for future host–pathogen studies of perennial plants requiring a holistic approach. PMID:17650512

In vitro biocompatibility of EPM and EPDM rubbers.

PubMed

Mast, F; Hoschtitzky, J A; Van Blitterswijk, C A; Huysmans, H A

1997-01-01

The in vitro toxicity of two EPDM rubbers (K 778 and K 4802) and one EPM rubber (K 740) was tested using human fibroblasts. The modulus of elasticity of each rubber was varied by exposure to different amounts of electron-beam radiation (0, 5 and 10 Mrad). The short-term in vitro toxicity was tested by culturing cells on polymer films. The long-term effect of ageing was simulated by growing fibroblasts in nutrient media prepared from extracts of heat-exposed materials. Cell cultures were studied both quantitatively and (ultra) structurally. Growth curves obtained in the toxicity test did not differ significantly from control values at any day of observation, and also showed that electron-beam radiation did not alter the biocompatibility. The same results were found for all but one material in the artificial ageing test. The number of cells in the K4802/10 Mrad extraction medium was decreased. Ultrastructurally no gross deviations from normal morphology were observed, either in the direct contact test or in the artificial ageing test. The most characteristic feature was a somewhat dilated endoplasmic reticulum. In summary, the in vitro biocompatibility of EPDM-rubbers as observed in this study is satisfactory and motivates further investigation of their biocompatibility in animal experiments.

Identification of a Taraxacum brevicorniculatum rubber elongation factor protein that is localized on rubber particles and promotes rubber biosynthesis.

PubMed

Laibach, Natalie; Hillebrand, Andrea; Twyman, Richard M; Prüfer, Dirk; Schulze Gronover, Christian

2015-05-01

Two protein families required for rubber biosynthesis in Taraxacum brevicorniculatum have recently been characterized, namely the cis-prenyltransferases (TbCPTs) and the small rubber particle proteins (TbSRPPs). The latter were shown to be the most abundant proteins on rubber particles, where rubber biosynthesis takes place. Here we identified a protein designated T. brevicorniculatum rubber elongation factor (TbREF) by using mass spectrometry to analyze rubber particle proteins. TbREF is homologous to the TbSRPPs but has a molecular mass that is atypical for the family. The promoter was shown to be active in laticifers, and the protein itself was localized on the rubber particle surface. In TbREF-silenced plants generated by RNA interference, the rubber content was significantly reduced, correlating with lower TbCPT protein levels and less TbCPT activity in the latex. However, the molecular mass of the rubber was not affected by TbREF silencing. The colloidal stability of rubber particles isolated from TbREF-silenced plants was also unchanged. This was not surprising because TbREF depletion did not affect the abundance of TbSRPPs, which are required for rubber particle stability. Our findings suggest that TbREF is an important component of the rubber biosynthesis machinery in T. brevicorniculatum, and may play a role in rubber particle biogenesis and influence rubber production. © 2015 The Authors The Plant Journal © 2015 John Wiley & Sons Ltd.

TRAIL overexpression co-regulated by Egr1 and HRE enhances radiosensitivity of hypoxic A549 cells depending on its apoptosis inducing role.

PubMed

Yang, Yan-Ming; Fang, Fang; Li, Xin; Yu, Lei; Wang, Zhi-Cheng

2017-01-01

Ionizing radiation can upregulate the expression levels of TRAIL and enhance tumor cell apoptosis. While Early growth response 1 (Egr1) gene promoter has radiation inducible characteristics, the expression for exogenous gene controlled by Egr1 promoter could be enhanced by ionizing radiation, but its efficiency is limited by tissue hypoxia. Hypoxia response elements (HREs) are important hypoxic response regulatory sequences and sensitivity enhancers. Therefore, we chose TRAIL as the gene radiotherapy to observe whether it is regulated by Egr1 and HER and its effects on A549 cells and its mechanism. The pcDNA3.1-Egr1-TRAIL (pc-E-hsT) and pcDNA3.1-HRE/Egr1-TRAIL (pc-H/E-hsT) plasmids containing Egr1-hsTRAIL and HRE/Egr1-hsTRAIL were transfected into A549 cells, the cells were treated by hypoxia and radiation. The TRAIL mRNA in the cells and protein concentration in the culture supernatants were measured by RT-PCR and ELISA, respectively. Mean lethal dose D0 value was evaluated with colony forming assay. The cell apoptotic rates were analyzed by FCM and TUNEL assay. Expression of DR4, DR5 and cleaved caspase-3 proteins were analyzed by western blotting. It showed that TRAIL mRNA expression and TRAIL concentration all significantly increased under hypoxia and/or radiation. D0 value of pc-H/E‑hsT transfected cells under hypoxia was lowest, indicating more high radiosensitivity. Hypoxia could not cause the pc-E-hsT transfected cell apoptotic rate increase, but there were promoting effects in pc-H/E-hsT transfected cells. DR4 had not obvious change in pc-E-hsT and pc-H/E-hsT transfected cells under normoxic and hypoxic condition, otherwise, DR5 and cleaved caspase-3 increased mostly in pc-H/E-hsT transfected cells under hypoxic condition. TRAIL overexpression was co-regulated by Egr1 and HRE. TRAIL might promote hypoxic A549 cell radiosensitivity and induce apoptosis depending on DR5 to caspase-3 pathways.

In-depth survey report: control technology assessment of unit operations employed in oral-contraceptive tablet-making operations at Ortho Pharmaceutical Corporation, Raritan, New Jersey, June 13-17, 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anastas, M.Y.; Caplan, P.E.; Froehlich, P.A.

An on-site visit was made to the Ortho Pharmaceutical Corporation (OPC), Raritan, New Jersey to evaluate methods of controlling exposure to hazardous materials during the manufacturing of medications. OPC produced oral-contraceptive tablets containing norethindrone (NOR), mestranol, and ethynylestradiol (EE). Ventilation was an important engineering control at this site. Other engineering controls included the isolation of work procedures and automation of work practices for weighing ingredients, granulation of substances, tableting, and packaging. Area samples were taken for air monitoring of steroid concentration levels in each manufacturing area. Access to the work areas was only through the locker rooms. Samples taken inmore » the locker rooms revealed no detectable contaminant levels. Workers performing high risk activities wore air supplied vinyl suits and disposable rubber gloves. The vinyl suits had overshoes attached. For moderate risk activities the workers wore a disposable suit, rubber gloves and shoe covers. Appropriate respirators were provided. Workers in low risk activities wore disposable rubber gloves and appropriate respirators. Sampling indicated that processing workers experienced breathing-zone levels outside their vinyl suits of 16.40 and 0.36 micrograms/cubic meter of NOR and EE, respectively.« less

Falciparum Malaria Outbreak in Sabah Linked to an Immigrant Rubber Tapper.

PubMed

Jeffree, Saffree Mohammad; Ahmed, Kamruddin; Safian, Nazarudin; Hassan, Rohaizat; Mihat, Omar; Lukman, Khamisah Awang; Shamsudin, Shamsul Bahari; Kamaludin, Fadzilah

2018-01-01

Sabah is a Malaysian state situated in the northern part of Borneo, and it is endemic for malaria. The incidence of malaria is the lowest (0.05/1,000 population) in Penampang districts of Sabah. In June 26, 2012, two Plasmodium falciparum malaria cases were notified to public health department from a village in Penampang. Immediate investigation was initiated to identify the risk factors and to institute control measures. We performed active case finding by asking household members of all houses in the village regarding malaria symptoms and by examining blood smears. Environmental investigation was performed by collecting samples to detect mosquito breeding sites and to identify malaria transmitting vector mosquitoes. A case-control study with a ratio of 1:4 (11 cases and 44 controls) was conducted using self-administered questionnaire. The microscopic examination of blood smear for malarial parasite and entomology sampling was carried out. The malarial attack rate was 2.3%, 6/11 smears have gametocyte, and the case fatality rate was 9.1%. One case was a migrant rubber tapper from Indonesia which happened to be the first case with gametocyte positive. Overall, the incidence of malaria was higher (6/11) among rubber tappers. The odds of cases for those living nearby stagnant water were 7.3 [95% confidence interval: 1.2-43.5] times higher. In conclusion, an outbreak of P. falciparum malaria was introduced into a malaria-free village by a migrant rubber tapper, by whom the imported parasite was introduced to the community via vector Anopheles balabacensis . Living near stagnant water bodies was the risk factor in this outbreak.

Development of hand exoskeleton for rehabilitation of post-stroke patient

NASA Astrophysics Data System (ADS)

Zaid, Amran Mohd; Chean, Tee Chu; Sukor, Jumadi Abdul; Hanafi, Dirman

2017-10-01

Degenerative muscle diseases characterized by loss of strength in human hand significantly affect the physical of affected individuals. A soft assistive exoskeleton glove is designed to help post-stroke patient with their rehabilitation process. The glove uses soft bending actuator which has a rubber like tender characteristic. Due to its rubber like characteristic, flexion of finger can be achieved easily through pneumatic air without considering other hand motions. The application involves a post-stroke patient to wear the soft exoskeleton glove on his paralyzed hand and control the actuation of the glove by using pneumatic air source. The fabrication of the soft bending actuator involves silicone rubber Mold Star® 15 SLOW which falls within the soft category of shore A hardness scale. The soft bending actuator is controlled by Arduino Mega 2560 as main controller board and relay module is used to trigger the 3/2-way single solenoid valve by switching on the 24VDC power supply. The actuation of the soft bending actuator can be manipulated by setting delay ON and OFF for the relay switching. Thus, the repetition of the bending motion can be customized to fulfil the rehabilitation needs of the patient.

Pro-apoptotic signaling induced by Retinoic acid and dsRNA is under the control of Interferon Regulatory Factor-3 in breast cancer cells.

PubMed

Bernardo, Ana R; Cosgaya, José M; Aranda, Ana; Jiménez-Lara, Ana M

2017-07-01

Breast cancer is one of the most lethal malignancies for women. Retinoic acid (RA) and double-stranded RNA (dsRNA) are considered signaling molecules with potential anticancer activity. RA, co-administered with the dsRNA mimic polyinosinic-polycytidylic acid (poly(I:C)), synergizes to induce a TRAIL (Tumor-Necrosis-Factor Related Apoptosis-Inducing Ligand)- dependent apoptotic program in breast cancer cells. Here, we report that RA/poly(I:C) co-treatment, synergically, induce the activation of Interferon Regulatory Factor-3 (IRF3) in breast cancer cells. IRF3 activation is mediated by a member of the pathogen recognition receptors, Toll-like receptor-3 (TLR3), since its depletion abrogates IRF3 activation by RA/poly(I:C) co-treatment. Besides induction of TRAIL, apoptosis induced by RA/poly(I:C) correlates with the increased expression of pro-apoptotic TRAIL receptors, TRAIL-R1/2, and the inhibition of the antagonistic receptors TRAIL-R3/4. IRF3 plays an important role in RA/poly(I:C)-induced apoptosis since IRF3 depletion suppresses caspase-8 and caspase-3 activation, TRAIL expression upregulation and apoptosis. Interestingly, RA/poly(I:C) combination synergizes to induce a bioactive autocrine/paracrine loop of type-I Interferons (IFNs) which is ultimately responsible for TRAIL and TRAIL-R1/2 expression upregulation, while inhibition of TRAIL-R3/4 expression is type-I IFN-independent. Our results highlight the importance of IRF3 and type-I IFNs signaling for the pro-apoptotic effects induced by RA and synthetic dsRNA in breast cancer cells.

Design and implementation of an audit trail in compliance with US regulations.

PubMed

Jiang, Keyuan; Cao, Xiang

2011-10-01

Audit trails have been used widely to ensure quality of study data and have been implemented in computerized clinical trials data systems. Increasingly, there is a need to audit access to study participant identifiable information to provide assurance that study participant privacy is protected and confidentiality is maintained. In the United States, several federal regulations specify how the audit trail function should be implemented. To describe the development and implementation of a comprehensive audit trail system that meets the regulatory requirements of assuring data quality and integrity and protecting participant privacy and that is also easy to implement and maintain. The audit trail system was designed and developed after we examined regulatory requirements, data access methods, prevailing application architecture, and good security practices. Our comprehensive audit trail system was developed and implemented at the database level using a commercially available database management software product. It captures both data access and data changes with the correct user identifier. Documentation of access is initiated automatically in response to either data retrieval or data change at the database level. Currently, our system has been implemented only on one commercial database management system. Although our audit trail algorithm does not allow for logging aggregate operations, aggregation does not reveal sensitive private participant information. Careful consideration must be given to data items selected for monitoring because selection of all data items using our system can dramatically increase the requirements for computer disk space. Evaluating the criticality and sensitivity of individual data items selected can control the storage requirements for clinical trial audit trail records. Our audit trail system is capable of logging data access and data change operations to satisfy regulatory requirements. Our approach is applicable to virtually any data that can be stored in a relational database.

The Effectiveness at High Speeds of a 20-Percent-Chord Plain Trailing-Edge Flap on the NACA 65-210 Airfoil

NASA Technical Reports Server (NTRS)

Stivers, Louis S., Jr.

1947-01-01

An analysis has been made of the lift control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flap on the NACA 65-210 airfoil section. The analysis indicates that the plain trailing-edge flap employed on the 10-percent-thick airfoil at Mach numbers as high as 0.875 retains at least 50-percent of its low-speed lift-control effectiveness, and is sufficiently effective in lateral control application, assuming a rigid wing, to provide adequate airplane rolling characteristics. The plain trailing-edge flap, as compared to the spoiler and the dive-recovery flap, appears to afford the most favorable characteristics as a device for controlling lift continuously throughout the range of Mach numbers from 0.3 to 0.875. At Mach numbers above those for lift divergence of the wing, either a plain flap or a dive-recovery flap may be used on a thin airplane wing to provide auxiliary wing lift when the airplane is to be controlled in flight, other than in dives, at these Mach numbers. The choice of a lift-control device for this use, however, should include the consideration of other factors such as the increments of drag and pitching moment accompanying the use of the device, and the structural and high-speed aerodynamic characteristics of the airplane which is to employ the device.

Bio-Inspired Control of Roughness and Trailing Edge Noise

NASA Astrophysics Data System (ADS)

Clark, Ian Andrew

Noise from fluid flow over rough surfaces is an important consideration in the design and performance of certain vehicles with high surface-area-to-perimeter ratios. A new method of noise control based on the anatomy of owls is developed and consists of fabric or fibrous canopies suspended above the surface. The method is tested experimentally and is found to reduce the total far-field noise emitted by the surface. The treatment also is found to reduce the magnitude of pressure fluctuations felt by the underlying surface by up to three orders of magnitude. Experimental investigations into the effects of geometric parameters of the canopies lead to an optimized design which maximizes noise reduction. The results obtained during the canopy experiment inspired a separate new device for the reduction of trailing edge noise. This type of noise is generated by flow past the wing of an aircraft or the blades of a wind turbine, and is a source of annoyance for those in surrounding communities. The newly developed treatment consists of small fins, or "finlets," placed near the trailing edge of an airfoil. The treatment is tested experimentally at near-full-scale conditions and is found to reduce the magnitude of far-field noise by up to 10 dB. Geometric parameters of the finlets are tested to determine the optimal size and spacing of the finlets to maximize noise reduction. Follow-up computational and experimental studies reveal the fluid mechanics behind the noise reduction by showing that the finlets produce a velocity deficit in the flow near the trailing edge and limit the magnitude and spanwise correlation lengthscale of turbulence near the trailing edge, factors which determine the magnitude of far-field noise. In a final experiment, the finlets are applied to a marine propeller and are found to reduce not only trailing edge noise, but also noise caused by the bluntness of the trailing edge. The results of this experiment show the potential usefulness of finlets to reduce noise from rotating systems, such as fans or propellers, as well as from structures which feature blunt trailing edges.

Identification of natural rubber and characterization of rubber biosynthetic activity in fig tree.

PubMed

Kang, H; Kang, M Y; Han, K H

2000-07-01

Natural rubber was extracted from the fig tree (Ficus carica) cultivated in Korea as part of a survey of rubber producing plants. Fourier transform infrared and (13)C nuclear magnetic resonance analysis of samples prepared by successive extraction with acetone and benzene confirmed that the benzene-soluble residues are natural rubber, cis-1,4-polyisoprene. The rubber content in the latex of fig tree was about 4%, whereas the rubber content in the bark, leaf, and fruit was 0.3%, 0.1%, and 0.1%, respectively. Gel-permeation chromatography revealed that the molecular size of the natural rubber from fig tree is about 190 kD. Similar to rubber tree (Hevea brasiliensis) and guayule (Parthenium argentatum Gray), rubber biosynthesis in fig tree is tightly associated with rubber particles. The rubber transferase in rubber particles exhibited a higher affinity for farnesyl pyrophosphate than for isopentenyl pyrophosphate, with apparent K(m) values of 2.8 and 228 microM, respectively. Examination of latex serum from fig tree by sodium dodecyl sulfate-polyacrylamide gel electrophoresis revealed major proteins of 25 and 48 kD in size, and several proteins with molecular mass below 20 and above 100 kD. Partial N-terminal amino acid sequencing and immunochemical analyses revealed that the 25- and 48-kD proteins were novel and not related to any other suggested rubber transferases. The effect of EDTA and Mg(2+) ion on in vitro rubber biosynthesis in fig tree and rubber tree suggested that divalent metal ion present in the latex serum is an important factor in determining the different rubber biosynthetic activities in fig tree and rubber tree.

Identification of Natural Rubber and Characterization of Rubber Biosynthetic Activity in Fig Tree1

PubMed Central

Kang, Hunseung; Kang, Min Young; Han, Kyung-Hwan

2000-01-01

Natural rubber was extracted from the fig tree (Ficus carica) cultivated in Korea as part of a survey of rubber producing plants. Fourier transform infrared and 13C nuclear magnetic resonance analysis of samples prepared by successive extraction with acetone and benzene confirmed that the benzene-soluble residues are natural rubber, cis-1,4-polyisoprene. The rubber content in the latex of fig tree was about 4%, whereas the rubber content in the bark, leaf, and fruit was 0.3%, 0.1%, and 0.1%, respectively. Gel-permeation chromatography revealed that the molecular size of the natural rubber from fig tree is about 190 kD. Similar to rubber tree (Hevea brasiliensis) and guayule (Parthenium argentatum Gray), rubber biosynthesis in fig tree is tightly associated with rubber particles. The rubber transferase in rubber particles exhibited a higher affinity for farnesyl pyrophosphate than for isopentenyl pyrophosphate, with apparent Km values of 2.8 and 228 μm, respectively. Examination of latex serum from fig tree by sodium dodecyl sulfate-polyacrylamide gel electrophoresis revealed major proteins of 25 and 48 kD in size, and several proteins with molecular mass below 20 and above 100 kD. Partial N-terminal amino acid sequencing and immunochemical analyses revealed that the 25- and 48-kD proteins were novel and not related to any other suggested rubber transferases. The effect of EDTA and Mg2+ ion on in vitro rubber biosynthesis in fig tree and rubber tree suggested that divalent metal ion present in the latex serum is an important factor in determining the different rubber biosynthetic activities in fig tree and rubber tree. PMID:10889262

Systematic review of the evidence for Trails B cut-off scores in assessing fitness-to-drive

PubMed Central

Roy, Mononita; Molnar, Frank

2013-01-01

Background Fitness-to-drive guidelines recommend employing the Trail Making B Test (a.k.a. Trails B), but do not provide guidance regarding cut-off scores. There is ongoing debate regarding the optimal cut-off score on the Trails B test. The objective of this study was to address this controversy by systematically reviewing the evidence for specific Trails B cut-off scores (e.g., cut-offs in both time to completion and number of errors) with respect to fitness-to-drive. Methods Systematic review of all prospective cohort, retrospective cohort, case-control, correlation, and cross-sectional studies reporting the ability of the Trails B to predict driving safety that were published in English-language, peer-reviewed journals. Results Forty-seven articles were reviewed. None of the articles justified sample sizes via formal calculations. Cut-off scores reported based on research include: 90 seconds, 133 seconds, 147 seconds, 180 seconds, and < 3 errors. Conclusions There is support for the previously published Trails B cut-offs of 3 minutes or 3 errors (the ‘3 or 3 rule’). Major methodological limitations of this body of research were uncovered including (1) lack of justification of sample size leaving studies open to Type II error (i.e., false negative findings), and (2) excessive focus on associations rather than clinically useful cut-off scores. PMID:23983828

77 FR 23303 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-18

... the Order Audit Trail System Information Barriers Put Into Place by the ETP Holder in Reliance on... report to the Order Audit Trail System (``OATS'') information barriers put into place by the ETP Holder... uses an effective system of internal controls--such as appropriate information barriers--that operate...

Neuropsychological Assessment of Children with Hearing Impairment on Trail Making, Tactual Performance, and Category Tests.

ERIC Educational Resources Information Center

Kelly, Mark D.

1995-01-01

The performance of 42 hearing-impaired children and 42 matched hearing peers was examined on the Category, Tactual Performance, and Trail Making tests of the Halstead-Reitan Neuropsychological Battery for Older Children. The major finding was that performance of deaf students was similar to that of hearing controls. (SLD)

Comparative studies on the mechanical properties of natural rubber and natural rubber filled with multi-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

The present article compares the mechanical properties of natural rubber (NR) and carbon nanotubes (CNTs) filled natural rubber composites. Four types of nanocomposite specimens are fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. The specimens are tested for their mechanical properties. It is observed that the tensile strength, hardness and elongation break of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs. Percentage of the elongation at break of rubber CNTs composites is lower than that of raw rubber.

Mechanical Performance Test of Rubber-Powder Modified Concrete

NASA Astrophysics Data System (ADS)

Zhang, Yan Cong; Gao, Ling Ling

2018-06-01

A number of rubber cement concrete specimens that rubber powder dosage different were obtained using same cement, water and fine aggregates, by adjusting the dosage of rubber powder. Then it was used to research the influence of rubber powder dosage on performance of cement concrete by measuring its liquidity, strength and toughness. The results show that: when water-cement ratio was equal and rubber powder replacing the same volume sand, the fluidity of cement concrete almost linear increased with rubber powder dosage increasing. With dosage of rubber powder increasing, compressive strength and flexural strength reduced, but toughness linear growth trend when dosage of rubber powder less 30%.

How do rubber ( Hevea brasiliensis) plantations behave under seasonal water stress in northeastern Thailand and central Cambodia?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumagai, Tomo'omi; Mudd, Ryan G.; Giambelluca, Thomas W.

Plantation rubber ( Hevea brasiliensis Müll. Arg.) is a viable economic resource for Southeast Asian countries. Consequently, rubber plantations are rapidly expanding into both climatically optimal and sub-optimal environments throughout mainland Southeast Asia, potentially changing the partitioning of water, energy, and carbon at multiple scales, compared with the traditional land covers they are replacing. Delineating the characteristics of biosphere-atmosphere exchange in rubber plantations is therefore important to understanding the impacts of such land use change on environmental processes. We have conducted eddy flux measurements in two rubber plantation sites: (1) Som Sanuk (SS), located northern Thailand; and (2) Cambodian Rubbermore » Research Institute (CRRI), central Cambodia. Both sites have a distinct dry season. Measurements were made over a 3-year period. We used combination of actual evapotranspiration (E T) flux measurements and an inversed version of a simple 2-layer E T model for estimating the mean canopy stomatal conductances (g s), which is among the most effective measures for describing water and energy exchanges and tree water use characteristics. A main novelty in this analysis is that the rubber canopy conductance can be extracted from total surface conductance (including the canopy and the vegetation floor effects) and hence environmental and biological controls on rubber tree gs are explicitly compared at each site in different seasons and years. It is demonstrated how each studied rubber plantation copes with each strong seasonal drought via tree water use strategies. Potential tree water use deficit (precipitation (P) – potential evaporation (E T_POT)) for each season (i.e., December-February: DJF, March-May: MAM, June-August: JJA, and September-November: SON) revealed in which season and how the water use should be controlled. We found that in seasons when actual tree water use deficit (P – E T) was negative (i.e., DJF and MAM), the deficit was compensated by soil water from the previous season stored within the soil layer at depths of 0-2 m at the Thailand site, and at depths of 0-3 m at CRRI. Two ecophysiological parameters, the reference value of g s (g sref) and the sensitivity of g s to atmospheric demand (m), as well as their proportionality (m/g sref), were derived from the logarithmic response curve of g s to vapor pressure deficit (D) for each season and each site. At both sites, g sref and m appeared to be smaller in DJF and MAM than those in the other seasons (i.e., JJA and SON). On average in a whole year, m/g sref was less than 0.6 at SS and almost 0.6 at the CRRI site, suggesting that there was less sufficient stomatal regulation at SS, where the risk of water stress-induced hydraulic failure is low because of its high annual rainfall amount. In comparison, at CRRI where annual P – E T_POT was negative, there was stricter stomatal regulation that prevents excessive xylem cavitation. These tendencies imply that in the drier season, i.e., DJF and MAM, the rubber trees in SS and CRRI adopt the stomatal control strategy of changing g sref with reluctance and positive to change m, respectively.« less

Aerodynamic Characteristics at a Mach Number of 6.8 of Two Hypersonic Missile Configurations, One with Low-Aspect-Ratio Cruciform Fins and Trailing-Edge Flaps and One with a Flared Afterbody and All-Movable Controls

NASA Technical Reports Server (NTRS)

Robinson, Ross B; Bernot, Peter T

1958-01-01

An investigation has been made to determine the aerodynamic characteristics in pitch at a Mach number of 6.8 of hypersonic missile configurations with cruciform trailing-edge flaps and with all-movable control surfaces. The flaps were tested on a configuration having low-aspect-ratio cruciform fins with an apex angle of 5 deg the all-movable controls were mounted at the 46.7-percent body station on a configuration having a 10 deg flared afterbody. The tests were made through an angle-of-attack range of -2 deg to 20 deg at zero sideslip in the Langley 11-inch hypersonic tunnel. The results indicated that the all-movable controls on the flared afterbody model should be capable of producing much larger values of trim lift and of normal acceleration than the trailing-edge -flap configuration. The flared -after body configuration had considerably higher drag than the cruciform-fin model but only slightly lower values of lift drag ratio.

Aerodynamic Characteristics at a Mach Number of 6.8 of Two Hypersonic Missile Configurations, One with Low-Aspect-Ratio Cruciform Fins and Trailing-Edge Flaps and One with a Flared Afterbody and All-Movable Controls

NASA Technical Reports Server (NTRS)

Bernot, P. T.; Robinson, R. B.

1958-01-01

An investigation has been made to determine the aerodynamic characteristics in pitch at a Mach number of 6.8 of hypersonic missile configurations with cruciform trailing-edge flaps and with all-movable control surfaces. The flaps were tested on a configuration having low-aspect-ratio cruciform fins with an apex angle of 5 degrees; the all-movable controls were mounted at the 46.7-percent body station on a configuration having a 10 degrees flared afterbody. The tests were made through an angle-of-attack range of -2 degrees to 20 degrees at zero sideslip in the Langley 11-inch hypersonic tunnel. The results indicated that the all-movable controls on the flared-afterbody model should be capable of producing much larger values of trim lift and of normal acceleration than the trailing-edge-flap configuration. The flared-afterbody configuration had considerably higher drag than the cruciform-fin model but only slightly lower values of lift-drag ratio.

Preclinical Biosafety Evaluation of Genetically Modified Human Adipose Tissue-Derived Mesenchymal Stem Cells for Clinical Applications to Brainstem Glioma.

PubMed

Choi, Seung Ah; Yun, Jun-Won; Joo, Kyeung Min; Lee, Ji Yeoun; Kwak, Pil Ae; Lee, Young Eun; You, Ji-Ran; Kwon, Euna; Kim, Woo Ho; Wang, Kyu-Chang; Phi, Ji Hoon; Kang, Byeong-Cheol; Kim, Seung-Ki

2016-06-15

Stem-cell based gene therapy is a promising novel therapeutic approach for inoperable invasive tumors, including brainstem glioma. Previously, we demonstrated the therapeutic potential of human adipose tissue-derived mesenchymal stem cells (hAT-MSC) genetically engineered to express a secreted form of tumor necrosis factor-related apoptosis-inducing ligand (sTRAIL) against brainstem glioma. However, safety concerns should be comprehensively investigated before clinical applications of hAT-MSC.sTRAIL. At first, we injected stereotactically low (1.2 × 10(5) cells/18 μL), medium (2.4 × 10(5)/18 μL), or high dose (3.6 × 10(5)/18 μL) of hAT-MSC.sTRAIL into the brainstems of immunodeficient mice reflecting the plan of the future clinical trial. Local toxicity, systemic toxicity, secondary tumor formation, and biodistribution of hAT-MSC.sTRAIL were investigated. Next, presence of hAT-MSC.sTRAIL was confirmed in the brain and major organs at 4, 9, and 14 weeks in brainstem glioma-bearing mice. In the 15-week subchronic toxicity test, no serious adverse events in terms of body weight, food consumption, clinical symptom, urinalysis, hematology, clinical chemistry, organ weight, and histopathology were observed. In the 26-week tumorigenicity test, hAT-MSC.sTRAIL made no detectable tumors, whereas positive control U-87 MG cells made huge tumors in the brainstem. No remaining hAT-MSC.sTRAIL was observed in any organs examined, including the brainstem at 15 or 26 weeks. In brainstem glioma-bearing mice, injected hAT-MSC.sTRAIL was observed, but gradually decreased over time in the brain. The mRNA of human specific GAPDH and TRAIL was not detected in all major organs. These results indicate that the hAT-MSC.sTRAIL could be applicable to the future clinical trials in terms of biosafety.

40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber... manufacture of emulsion crumb rubber, other than acrylonitrilebutadiene rubber. [40 FR 18173, Apr. 25, 1975] ...

40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber... manufacture of emulsion crumb rubber, other than acrylonitrilebutadiene rubber. [40 FR 18173, Apr. 25, 1975] ...

40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber... manufacture of emulsion crumb rubber, other than acrylonitrilebutadiene rubber. [40 FR 18173, Apr. 25, 1975] ...

Interference in adhesion of bacteria and yeasts isolated from explanted voice prostheses to silicone rubber by rhamnolipid biosurfactants.

PubMed

Rodrigues, L R; Banat, I M; van der Mei, H C; Teixeira, J A; Oliveira, R

2006-03-01

The effects and extent of adhesion of four different bacterial and two yeast strains isolated from explanted voice prostheses to silicone rubber with and without an adsorbed rhamnolipid biosurfactant layer obtained from Pseudomonasaeruginosa DS10-129 was studied. The ability of rhamnolipid biosurfactant to inhibit adhesion of micro-organisms to silicone rubber was investigated in a parallel-plate flow chamber. The anti-adhesive activity of the biosurfactant at different concentrations was significant against all the strains and depended on the micro-organism tested. The results showed an effective reduction in the initial deposition rates, and the number of bacterial cells adhering after 4 h, for all micro-organisms tested at the 4 g l(-1) undiluted rhamnolipid solution. Maximum initial reduction of adhesion rate (an average of 66%) occurred for Streptococcus salivarius GB 24/9 and Candida tropicalis GB 9/9. The number of cells adhering after 4 h on silicone rubber conditioned with biosurfactant was reduced to 48% for Staphylococcus epidermidis GB 9/6, Strep. salivarius GB 24/9, Staphylococcus aureus GB 2/1 and C. tropicalis GB 9/9 in comparison to controls. Perfusing the flow chamber with biosurfactant containing solution followed by the passage of a liquid-air interface, to investigate detachment of micro-organisms adhering to silicone rubber, produced high detachment (96%) of adhered cells for all micro-organisms studied, except for Staph. aureus GB 2/1 (67%). It is concluded that biosurfactant represent suitable compounds that should be considered in developing future strategies to prevent the microbial colonization of silicone rubber voice prostheses.

Strength and microstructure characteristics of the recycled rubber tire-sand mixtures as lightweight backfill.

PubMed

Zhang, Tao; Cai, Guojun; Duan, Weihong

2018-02-01

The disposal of scrap rubber tires has induced critical environmental issue worldwide due to the rapid increase in the number of vehicles. Recycled scrap tires as a construction material in civil engineering have significant environmental benefits from a waste management perspective. A systematic study that deals with strength and microstructure characteristics of the rubber-sand mixtures is initiated, and mechanical response of the mixtures is discussed in this investigation. Experiments were conducted to evaluate the effects of rubber fraction on the basic properties including mass density (ρ), stress-strain characteristics, shear strength, and unconfined compression strength (q u ) of the rubber-sand mixtures. Additionally, scanning electron microscopy (SEM) was carried out to reveal the microstructure characteristics of the mixtures with various rubber fractions. A discussion on the micromechanics of the mixtures also was conducted. This study demonstrates that the ρ, friction angle, and q u decrease linearly with an increase in rubber fraction, whereas shear strain at peak increases. The stress-strain characteristics of the rubber-sand mixtures shift from brittle to ductile as the rubber fraction increase. These changes are attributed to remarkably lower stiffness and higher compressibility of the rubber particle compared with those of the conventional mineral aggregates. With an increase in the rubber fraction, the mechanical response of rubber-sand mixtures exhibits two types: sand-like material and rubber-like material. Rubber particle possesses the capacity to prevent the contacted sand particles from sliding at lower rubber fraction, whereas it transmits the applied loadings as the rubber fraction increased. This outcome reinforces the practicability of using recycled rubber tire-sand mixtures as a lightweight backfill in subbase/base applications.

Experimental Investigation of the Mechanical and Durability Properties of Crumb Rubber Concrete.

PubMed

Liu, Hanbing; Wang, Xianqiang; Jiao, Yubo; Sha, Tao

2016-03-07

Recycling waste tire rubber by incorporating it into concrete has become the preferred solution to dispose of waste tires. In this study, the effect of the volume content of crumb rubber and pretreatment methods on the performances of concrete was evaluated. Firstly, the fine aggregate and mixture were partly replaced by crumb rubber to produce crumb rubber concrete. Secondly, the mechanical and durability properties of crumb rubber concrete with different replacement forms and volume contents had been investigated. Finally, the crumb rubber after pretreatment by six modifiers was introduced into the concrete mixture. Corresponding tests were conducted to verify the effectiveness of pretreatment methods as compared to the concrete containing untreated crumb rubber. It was observed that the mechanical strength of crumb rubber concrete was reduced, while durability was improved with the increasing of crumb rubber content. 20% replacement of fine aggregate and 5% replacement of the total mixture exhibited acceptable properties for practical applications. In addition, the results indicated that the modifiers had a positive impact on the mechanical and durability properties of crumb rubber concrete. It avoided the disadvantage of crumb rubber concrete having lower strength and provides a reference for the production of modified crumb rubber concrete.

Experimental Investigation of the Mechanical and Durability Properties of Crumb Rubber Concrete

PubMed Central

Liu, Hanbing; Wang, Xianqiang; Jiao, Yubo; Sha, Tao

2016-01-01

Recycling waste tire rubber by incorporating it into concrete has become the preferred solution to dispose of waste tires. In this study, the effect of the volume content of crumb rubber and pretreatment methods on the performances of concrete was evaluated. Firstly, the fine aggregate and mixture were partly replaced by crumb rubber to produce crumb rubber concrete. Secondly, the mechanical and durability properties of crumb rubber concrete with different replacement forms and volume contents had been investigated. Finally, the crumb rubber after pretreatment by six modifiers was introduced into the concrete mixture. Corresponding tests were conducted to verify the effectiveness of pretreatment methods as compared to the concrete containing untreated crumb rubber. It was observed that the mechanical strength of crumb rubber concrete was reduced, while durability was improved with the increasing of crumb rubber content. 20% replacement of fine aggregate and 5% replacement of the total mixture exhibited acceptable properties for practical applications. In addition, the results indicated that the modifiers had a positive impact on the mechanical and durability properties of crumb rubber concrete. It avoided the disadvantage of crumb rubber concrete having lower strength and provides a reference for the production of modified crumb rubber concrete. PMID:28773298

Camera trap placement and the potential for bias due to trails and other features

PubMed Central

Forrester, Tavis D.

2017-01-01

Camera trapping has become an increasingly widespread tool for wildlife ecologists, with large numbers of studies relying on photo capture rates or presence/absence information. It is increasingly clear that camera placement can directly impact this kind of data, yet these biases are poorly understood. We used a paired camera design to investigate the effect of small-scale habitat features on species richness estimates, and capture rate and detection probability of several mammal species in the Shenandoah Valley of Virginia, USA. Cameras were deployed at either log features or on game trails with a paired camera at a nearby random location. Overall capture rates were significantly higher at trail and log cameras compared to their paired random cameras, and some species showed capture rates as much as 9.7 times greater at feature-based cameras. We recorded more species at both log (17) and trail features (15) than at their paired control cameras (13 and 12 species, respectively), yet richness estimates were indistinguishable after 659 and 385 camera nights of survey effort, respectively. We detected significant increases (ranging from 11–33%) in detection probability for five species resulting from the presence of game trails. For six species detection probability was also influenced by the presence of a log feature. This bias was most pronounced for the three rodents investigated, where in all cases detection probability was substantially higher (24.9–38.2%) at log cameras. Our results indicate that small-scale factors, including the presence of game trails and other features, can have significant impacts on species detection when camera traps are employed. Significant biases may result if the presence and quality of these features are not documented and either incorporated into analytical procedures, or controlled for in study design. PMID:29045478

Influence of Cattle Trails on Runoff Quantity and Quality.

PubMed

Miller, Jim J; Curtis, Tony; Chanasyk, David S; Willms, Walter D

2017-03-01

Cattle trails in grazed pastures close to rivers may adversely affect surface water quality of the adjacent river by directing runoff to it. The objective of this 3-yr study (2013-2015) in southern Alberta, Canada, was to determine if cattle trails significantly increased the risk of runoff and contaminants (sediment, nutrients) compared with the adjacent grazed pasture (control). A portable rainfall simulator was used to generate artificial rainfall (140 mm h) and runoff. The runoff properties measured were time to runoff and initial abstraction (infiltration), total runoff depth and average runoff rates, as well as concentrations and mass loads of sediment, N, and P fractions. Cattle trails significantly ( ≤ 0.10) decreased time to runoff and initial abstraction (26-32%) in the 2 yr measured and increased total runoff depth, runoff coefficients, and average runoff rates (21-51%) in 2 of 3 yr. Concentrations of sediment, N, and P fractions in runoff were not significantly greater for cattle trails than for control areas. However, mass loads of total suspended solids (57-85% increase), NH-N (31-90%), and dissolved reactive P (DRP) (30-92%) were significantly greater because of increased runoff volumes. Overall, runoff quantity and loads of sediment, NH-N, and DRP were greater for cattle trails compared with the adjacent grazed pasture, and hydrologic connection with cattle-access sites on the riverbank suggests that this could adversely affect water quality in the adjacent river. Extrapolation of the study results should be tempered by the specific conditions represented by this rainfall simulation study. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Camera trap placement and the potential for bias due to trails and other features.

PubMed

Kolowski, Joseph M; Forrester, Tavis D

2017-01-01

Camera trapping has become an increasingly widespread tool for wildlife ecologists, with large numbers of studies relying on photo capture rates or presence/absence information. It is increasingly clear that camera placement can directly impact this kind of data, yet these biases are poorly understood. We used a paired camera design to investigate the effect of small-scale habitat features on species richness estimates, and capture rate and detection probability of several mammal species in the Shenandoah Valley of Virginia, USA. Cameras were deployed at either log features or on game trails with a paired camera at a nearby random location. Overall capture rates were significantly higher at trail and log cameras compared to their paired random cameras, and some species showed capture rates as much as 9.7 times greater at feature-based cameras. We recorded more species at both log (17) and trail features (15) than at their paired control cameras (13 and 12 species, respectively), yet richness estimates were indistinguishable after 659 and 385 camera nights of survey effort, respectively. We detected significant increases (ranging from 11-33%) in detection probability for five species resulting from the presence of game trails. For six species detection probability was also influenced by the presence of a log feature. This bias was most pronounced for the three rodents investigated, where in all cases detection probability was substantially higher (24.9-38.2%) at log cameras. Our results indicate that small-scale factors, including the presence of game trails and other features, can have significant impacts on species detection when camera traps are employed. Significant biases may result if the presence and quality of these features are not documented and either incorporated into analytical procedures, or controlled for in study design.

A comparative study of ground tire rubber devulcanization using twin screw extruder and internal mixer

NASA Astrophysics Data System (ADS)

Ujianto, O.; Putri, D. B.; Jayatin; AWinarto, D.

2017-07-01

Devulcanization of ground tire rubber (GTR) was done using twin screw extruder (TSE) and internal mixer (IM). Processing parameters were varied to analyze its effect on gel content. Fourier Transform Infrared Spectroscopy (FTIR) analysis was performed as qualitative technique to confirm structural change. The devulcanized rubbers with the least gel content percentage produced in both TSE and IM were then used as filler in natural rubber (NR)/coconut coir (CC) composite preparation. Effects of gel content percentage on NR/CC composite tensile strength and elongation at break were analyzed. The results show that the gel content decreased by 41% for sample processed in TSE and 50% in IM compared to control sample. Overall, the devulcanization is influenced by high energy generated by thermal or thermo-mechanical process. FTIR spectra show chemically structural changes of GTR as C=C, CH2, CH3 with higher intensity for IM sample than its counterpart indicated devulcanization. The replacement of GTR to DGTR on NR/CC/GTR composites provided less network structures and resulted better tensile strength and elongation at break.

Analysis of material parameter effects on fluidlastic isolators performance

NASA Astrophysics Data System (ADS)

Cheng, Q. Y.; Deng, J. H.; Feng, Z. Z.; Qian, F.

2018-01-01

Control of vibration in helicopters has always been a complex and challenging task. The fluidlastic isolators become more and more widely used because the fluids are non-toxic, non-corrosive, nonflammable, and compatible with most elastomers and adhesives. In the field of the fluidlastic isolators design, the selection of design parameters of fluid and rubber is very important to obtain efficient vibration-suppressed. Aiming at getting the property of fluidlastic isolator to material design parameters, a dynamic equation is set up based on the dynamic theory. And the dynamic analysis is carried out. The influences of design parameters on the property of fluidlastic isolator are calculated. The material parameters examined are the properties of fluid and rubber. Analysis results showed that the design parameters such as density of fluid, viscosity coefficient of fluid, stiffness of rubber (K1) and loss coefficient of rubber have obvious influence on the performance of isolator. Base on the results of the study it is concluded that the efficient vibration-suppressed can be obtained by the selection of design parameters.

Silencing the lettuce homologs of small rubber particle protein does not influence natural rubber biosynthesis in lettuce (Lactuca sativa).

PubMed

Chakrabarty, Romit; Qu, Yang; Ro, Dae-Kyun

2015-05-01

Natural rubber, cis-1,4-polyisoprene, is an important raw material in chemical industries, but its biosynthetic mechanism remains elusive. Natural rubber is known to be synthesized in rubber particles suspended in laticifer cells in the Brazilian rubber tree (Hevea brasiliensis). In the rubber tree, rubber elongation factor (REF) and its homolog, small rubber particle protein (SRPP), were found to be the most abundant proteins in rubber particles, and they have been implicated in natural rubber biosynthesis. As lettuce (Lactuca sativa) can synthesize natural rubber, we utilized this annual, transformable plant to examine in planta roles of the lettuce REF/SRPP homologs by RNA interference. Among eight lettuce REF/SRPP homologs identified, transcripts of two genes (LsSRPP4 and LsSRPP8) accounted for more than 90% of total transcripts of REF/SRPP homologs in lettuce latex. LsSRPP4 displays a typical primary protein sequence as other REF/SRPP, while LsSRPP8 is twice as long as LsSRPP4. These two major LsSRPP transcripts were individually and simultaneously silenced by RNA interference, and relative abundance, polymer molecular weight, and polydispersity of natural rubber were analyzed from the LsSRPP4- and LsSRPP8-silenced transgenic lettuce. Despite previous data suggesting the implications of REF/SRPP in natural rubber biosynthesis, qualitative and quantitative alterations of natural rubber could not be observed in transgenic lettuce lines. It is concluded that lettuce REF/SRPP homologs are not critically important proteins in natural rubber biosynthesis in lettuce. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of a Two-Piece Mask and Lens and Mold for Same.

DTIC Science & Technology

1980-05-01

Antioxidants in EPDM -6150C Heat - Ref. No. Antioxidant Composition of Antioxidant % gel aged Unaged QA0010-Q Control 98.16 1 3.5 -1 Agerite NA Polymeric...Uniroyal. With the exception of Royalene 100, which is an SPu, the types we examined are EPDM rubbers . Our trials with Royalene 100 were not successful...with aliphatic hydrocarbons is probably what explains the good compatibility of this resin with EPDM rubbers , one of our candidate polymers. Elvax resins

Simulated Solar Heat Tests of M.U.S.T. Air-Inflatable, Double-Wall Hospital Ward Shelters

DTIC Science & Technology

1974-05-01

fro« Controlling Off! CO.) R3AD INSTRUCTIONS BEFORE COMPLETING FORM S. RECIPIENT’S CATALOO NUMBER TYRE OF REPORT ft PERIOD COVERED S. PERFORMING...tape to coated side of web. 3. All pressure relief valves have the 1.75 ± .25 psi springs installed, 4. Pressure relief valve collars are rubber discs...pressure relief valve collars are of the fabric patch design in lieu of specified rubber disc. Each patch was installed using 52544 advesive. 5. All

Shock and Vibration Symposium (59th) Held in Albuquerque, New Mexico on 18-20 October 1988. Volume 2

DTIC Science & Technology

1988-10-01

030 in. Thick V-45 Rubber Shear Ply Aluminum Coated Steel Snap- FM-73 Film NAS 6703 Bolts ring 7 Polar Layers - M7885/4 Rivets 76 Required 11.5 Deg...Feedback Q. Zhang, S. Shelley 1. N. Lou and R. J. Allemang Relating Material Properties and Wave Effects in Vibration Isolators M. C. Reid, S. 0...Load-Deflection Characteristics of Rubber Element for Vibration Control Devices E. I. Rivin and B. S. Lee Vi ______ _____________ AIRBLAST Envelope

HIPAA-compliant automatic monitoring system for RIS-integrated PACS operation

NASA Astrophysics Data System (ADS)

Jin, Jin; Zhang, Jianguo; Chen, Xiaomeng; Sun, Jianyong; Yang, Yuanyuan; Liang, Chenwen; Feng, Jie; Sheng, Liwei; Huang, H. K.

2006-03-01

As a governmental regulation, Health Insurance Portability and Accountability Act (HIPAA) was issued to protect the privacy of health information that identifies individuals who are living or deceased. HIPAA requires security services supporting implementation features: Access control; Audit controls; Authorization control; Data authentication; and Entity authentication. These controls, which proposed in HIPAA Security Standards, are Audit trails here. Audit trails can be used for surveillance purposes, to detect when interesting events might be happening that warrant further investigation. Or they can be used forensically, after the detection of a security breach, to determine what went wrong and who or what was at fault. In order to provide security control services and to achieve the high and continuous availability, we design the HIPAA-Compliant Automatic Monitoring System for RIS-Integrated PACS operation. The system consists of two parts: monitoring agents running in each PACS component computer and a Monitor Server running in a remote computer. Monitoring agents are deployed on all computer nodes in RIS-Integrated PACS system to collect the Audit trail messages defined by the Supplement 95 of the DICOM standard: Audit Trail Messages. Then the Monitor Server gathers all audit messages and processes them to provide security information in three levels: system resources, PACS/RIS applications, and users/patients data accessing. Now the RIS-Integrated PACS managers can monitor and control the entire RIS-Integrated PACS operation through web service provided by the Monitor Server. This paper presents the design of a HIPAA-compliant automatic monitoring system for RIS-Integrated PACS Operation, and gives the preliminary results performed by this monitoring system on a clinical RIS-integrated PACS.

Computational Evaluation of the Steady and Pulsed Jet Effects on the Performance of a Circulation Control Wing Section

NASA Technical Reports Server (NTRS)

Liu, Yi; Sankar, Lakshmi N.; Englar, Robert; Ahuja, K.; Gaeta, R.

2003-01-01

Circulation Control Wing (CCW) technology is a very effective way of achieving very high lift coefficients needed by aircraft during take-off and landing. This technology can also be used to directly control the flow field over the wing. Compared to a conventional high-lift system, a Circulation Control Wing (CCW) can generate the required values of lift coefficient C(sub L,max) during take-off/landing with fewer or no moving parts and much less complexity. Earlier designs of CCW configurations used airfoils with a large radius rounded trailing edge to maximize the lift benefit. However, these designs also produced very high drag. These high drag levels associated with the blunt, large radius trailing edge can be prohibitive under cruise conditions when Circulation Control is no longer necessary. To overcome this difficulty, an advanced CCW section, i.e., a circulation hinged flap was developed to replace the original rounded trailing edge CC airfoil. This concept developed by Englar is shown. The upper surface of the CCW flap is a large-radius arc surface, but the lower surface of the flap is flat. The flap could be deflected from 0 degrees to 90 degrees. When an aircraft takes-off or lands, the flap is deflected as in a conventional high lift system. Then this large radius on the upper surface produces a large jet turning angle, leading to high lift. When the aircraft is in cruise, the flap is retracted and a conventional sharp trailing edge shape results, greatly reducing the drag. This kind of flap does have some moving elements that increase the weight and complexity over an earlier CCW design. But overall, the hinged flap design still maintains most of the Circulation Control high lift advantages, while greatly reducing the drag in cruising condition associated with the rounded trailing edge CCW design. In the present work, an unsteady three-dimensional Navier-Stokes analysis procedure has been developed and applied to this advanced CCW configuration. The solver can be used in both a 2-D and a 3-D mode, and can thus model airfoils as well as finite wings. The jet slot location, slot height, and the flap angle can all be varied easily and individually in the grid generator and the flow solver. Steady jets, pulsed jets, the leading edge and trailing edge blowing can all be studied with this solver.

Active Flow Separation Control on a NACA 0015 Wing Using Fluidic Actuators

NASA Technical Reports Server (NTRS)

Melton, Latunia P.

2014-01-01

Results are presented from a recent set of wind tunnel experiments using sweeping jet actuators to control ow separation on the 30% chord trailing edge ap of a 30 deg. swept wing model with an aspect ratio (AR) of 4.35. Two sweeping jet actuator locations were examined, one on the flap shoulder and one on the trailing edge flap. The parameters that were varied included actuator momentum, freestream velocity, and trailing edge flap deflection (Delta f ) angle. The primary focus of this set of experiments was to determine the mass flow and momentum requirements for controlling separation on the flap, especially at large flap deflection angles which would be characteristic of a high lift system. Surface pressure data, force and moment data, and stereoscopic particle image velocimetry (PIV) data were acquired to evaluate the performance benefits due to applying active flow control. Improvements in lift over the majority of the wing span were obtained using sweeping jet actuator control. High momentum coefficient, Cu, levels were needed when using the actuators on the ap because they were located downstream of separation. Actuators on the flap shoulder performed slightly better but actuator size, orientation, and spacing still need to be optimized.

Polishing performance of multiple-use silicone rubber-based polishing instruments with and without disinfection/sterilization.

PubMed

Heintze, Siegward Dietmar; Forjanic, Monika

2008-10-01

To evaluate the effect of the multiple-use of a three-step rubber-based polishing system on the polishing performance with and without a disinfection/sterilization protocol with prolonged disinfection (overnight). The three-step polishing system Astropol was applied under standardized contact pressure of 2 N on 320 grit pre-roughened flat composite specimens of Tetric EvoCeram for 10 seconds (F and P disc) and 30 seconds (HP disc) respectively. After each polishing step, the surface gloss and roughness were measured with a glossmeter and an optical sensor (FRT MicroProf), respectively. Material loss of the composite specimens and polishing instruments were measured after each step with a high precision digital scale. For all four variables (surface gloss, surface roughness, composite loss, loss of rubber material) the mean percentage of change compared to the reference was calculated. Already after the first use, the instruments which were used without disinfection or sterilization demonstrated a statistically significantly reduced polishing performance in all polishing steps compared to the reference (new polishing system) (t-test, P < 0.05). In addition, this loss in performance further increased with the second and third re-use. Especially the third component (Astropol HP) was affected by performance loss. By contrast, the multiple-use of the instruments which were subjected to prolonged disinfection did not result in a reduced polishing performance. For the P disc, a statistically significant improvement of the polishing performance could be observed throughout almost all multiple-use sessions (ANOVA, P < 0.05). The improved polishing performance was, however, accompanied by an increased loss of the silicone rubber material of the P and F polishing discs; the HP discs were not affected by this loss. Furthermore, particles of the rubber material also adhered to the composite. The polishing performance of the discs which were only subjected to the sterilization process was not statistically significantly different to the polishing performance of the control group in terms of surface roughness; but the surface gloss was worse than that of the control group. No loss of rubber material or adherence to the composite was observed in this group.

40 CFR 428.50 - Applicability; description of the small-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... RUBBER MANUFACTURING POINT SOURCE CATEGORY Small-Sized General Molded, Extruded, and Fabricated Rubber..., foam rubber backing, rubber cement-dipped goods, and retreaded tires by small-sized plants...

40 CFR 428.70 - Applicability; description of the large-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... RUBBER MANUFACTURING POINT SOURCE CATEGORY Large-Sized General Molded, Extruded, and Fabricated Rubber..., foam rubber backing, rubber cement-dipped goods, and retreaded tires by large-sized plants...

Conversion of tropical forests to smallholder rubber and oil palm plantations impacts nutrient leaching losses and nutrient retention efficiency in highly weathered soils

NASA Astrophysics Data System (ADS)

Kurniawan, Syahrul; Corre, Marife D.; Matson, Amanda L.; Schulte-Bisping, Hubert; Rahayu Utami, Sri; van Straaten, Oliver; Veldkamp, Edzo

2017-04-01

We examined the impact of forest conversion to rubber and oil palm plantations on nutrient leaching and nutrient retention efficiency in the soil. In Jambi province, Indonesia, we selected two landscapes with highly weathered Acrisol soils, which differed in texture: loam and clay. Within each landscape, we compared two reference land uses (lowland forest and jungle rubber, defined as rubber trees interspersed in secondary forest) with two converted land uses (smallholder rubber and oil palm plantations). The first three land uses were represented by four replicate sites and the oil palm by three sites within each landscape. We measured leaching losses using suction cup lysimeters, sampled biweekly to monthly from February to December 2013. In these highly weathered soils, texture controlled nutrient- and water-holding capacity and leaching losses. The clay Acrisol reference land uses had larger soil cation exchange capacity, base saturation and soil organic C than those in the loam Acrisol; this resulted in lower leaching of dissolved N and base cations (P=0.01-0.06) and in higher retention efficiency of N and base cations in the clay soils (P<0.01-0.07). The fertilized area in smallholder oil palm plantations resulted in increased leaching of dissolved N, organic C and base cation (P<0.01-0.08) and in reduced N and base cation retention efficiencies compared to the reference land uses and/or the rubber plantations (P<0.01), particularly in the loam Acrisol. Additionally, N fertilization in the loam Acrisol oil palm plantations had decreased soil solution pH and increased dissolved Al. The unfertilized rubber plantations had low nutrient leaching fluxes brought about by its reduced soil fertility. Our results highlight the importance of developing soil management practices to maintain soil fertility in unfertilized rubber plantations and to increase nutrient retention efficiency in fertilized oil palm plantations in order to minimize the reductions of ecosystem provisioning services (e.g., soil fertility and water quality) in these converted landscapes.

Digging more in the genetic risk prediction of hepatitis C virus epidemic in Egypt: Apoptosis genes polymorphisms in the susceptibility of hepatitis C virus and association with viral load.

PubMed

Khalifa, Rania H; Shahin, Rasha Mohamad Hosny; Aboukhalil, Reham Emad Eldin; Marie, Mohamed A; El-Deeb, Amr M; Riad, Nermine Magdi

2017-06-15

Egypt is confronted with the highest hepatitis C virus (HCV) epidemic. Apoptosis and cellular immune responses are crucial to the clearance or persistence of viral infections. This case-control study was carried out to detect whether apoptosis genes single nucleotide polymorphisms (SNPs) confer risk to HCV in a cohort of Egyptian patients and to explore their association with viral load. One hundred and ninety six blood samples were withdrawn from 96 HCV patients and 100 controls. The Tumor necrosis factor-related apoptosis inducing ligand (TRAIL) -1525G>A and FasL-844T>C SNPs were genotyped using the polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP). Hepatitis C viral load was measured using Real time PCR. Results Genotypes distributions of TRAIL -1525G>A and FasL-844 T>C polymorphisms in controls were in accordance with Hardy-Weinberg equilibrium (p>0.05). The study showed a statistically significant difference in the distribution of the TRAIL -1525G>A polymorphism genotypes and the FasL-844 T>C polymorphism genotypes between the HCV patients and the controls (p=0.001 and 0.02 respectively), with association of the -1525GA genotype and -844 TT genotype with increased risk of HCV infection (OR=2.68, 1.942 respectively, 95% CI=1.482-4.846, 1.1-3.43, respectively). No significant association was detected between TRAIL, FasL and the viral load. Our results suggest that the FasL -844T>C SNP is implicated in the susceptibility to HCV in Egyptian patients and firstly report the involvement of TRAIL gene polymorphism in the risk of the disease. Therefore we recommend national programs to delineate genetic factors that may put individuals at risk for contracting HCV. Copyright © 2017 Elsevier B.V. All rights reserved.

Criteria for asphalt-rubber concrete in civil airport pavements: Mixture design

NASA Astrophysics Data System (ADS)

Roberts, F. L.; Lytton, R. L.; Hoyt, D.

1986-07-01

A mixture design procedure is developed to allow the use of asphalt-rubber binders in concrete for flexible airport pavement. The asphalt-rubber is produced by reacting asphalt with ground, scrap tire rubber to produce the binder for the asphalt-rubber concrete. Procedures for laboratory preparation of alsphalt-rubber binders using an equipment setup that was found by researchers to produce laboratory binders with similar properties to field processes are included. The rubber-asphalt concrete mixture design procedure includes adjustments to the aggregate gradation to permit space for the rubber particles in the asphalt-rubber binder as well as suggested mixing and compaction temperatures, and compaction efforts. While the procedure was used in the laboratory to successfully produce asphalt-rubber concrete mixtures, it should be evaluated in the field to ensure that consistent results can be achieved in a production environment.

An analytical approach for the non-invasive selection of consolidants in rubber artworks.

PubMed

Manfredi, Marcello; Barberis, Elettra; Rava, Antonio; Poli, Tommaso; Chiantore, Oscar; Marengo, Emilio

2016-08-01

The effectiveness of five polymeric materials for the long-term conservation and restoration of rubber artworks was evaluated by accelerated photo-oxidative degradation studies. Two different ethylene vinyl-acetate resins, generally used in industry and uncommon in conservation field, a new water-based polyurethane, and two ethylene butyl-acrylate resins were assessed for the consolidation of rubber. By monitoring their degradation along time with LED imaging coupled to statistics and Fourier transform infrared spectroscopy (FTIR), the polymeric materials with the best properties that ensure the protection and security of the artwork were identified. The degradation was performed in solar box simulating the light exposure in a museum, under controlled temperature at no more than 35 °C in order to exclude the thermal effects that could influence the ageing of polymers. The mechanical stress of the treated samples was also investigated. The spectroscopic analyses, the chromatic changes study, and the mechanical degradation were used as indicators of the consolidant stability, allowing the evaluation of the materials selected for the consolidation and conservation of rubber. The ethylene-vinyl acetate copolymers resulted the most stable and suitable for the conservation of rubber artworks. Lastly, the conservation treatment identified in this research was employed for the restoration of the contemporary artwork "Presagi di Birnam" made with bicycle inner tubes by the artist Carol Rama.

Feasibility study of a soil-based rubberized CLSM.

PubMed

Wu, Jason Y; Tsai, Mufan

2009-02-01

The development of beneficial uses of recycled scrap tires is always in great demand around the world. The disposal of on-site surplus excavated soil and the production of standard engineering aggregates have also been facing increasing environmental and ecological challenges in congested islands, such as Taiwan. This paper presents an experimental study using recycled crumb rubber and native silty sand to produce a lightweight, soil-based, rubberized controlled low strength material (CLSM) for a bridge approach repair. To assess the technical feasibility of this material, the effects of weight ratios of cement-to-water (C/W) and water-to-solid (W/S), and of rubber content on the engineering properties for different mixtures were investigated. The presented test results include flowability, unit weight, strength, settlement potential, and bearing capacity. Based on the findings, we conclude that a soil-based rubberized CLSM with 40% sand by weight and an optimal design ratio of 0.7 for C/W and 0.35 for W/S can be used for the proposed bridge approach repair. Such a mixture has demonstrated acceptable flowability, strength, and bearing capacity. Its lower unit weight, negligible compressibility, and hydrocollapse potential also help ensure that detrimental settlement is unlikely to occur. The results illustrate a novel scheme of CLSM production, and suggest a beneficial alternative for the reduction of scrap tires as well as conservation of resources and environment.

Microwave treatment of vulcanized rubber

DOEpatents

Wicks, George G [Aiken, SC; Schulz, Rebecca L [Aiken, SC; Clark, David E [Gainesville, FL; Folz, Diane C [Gainesville, FL

2002-07-16

A process and resulting product is provided in which a vulcanized solid particulate, such as vulcanized crumb rubber, has select chemical bonds broken by microwave radiation. The direct application of microwaves in combination with uniform heating of the crumb rubber renders the treated crumb rubber more suitable for use in new rubber formulations. As a result, larger particle sizes and/or loading levels of the treated crumb rubber can be used in new rubber mixtures to produce recycled composite products with good properties.

F/A-18 Performance Benefits Measured During the Autonomous Formation Flight Project

NASA Technical Reports Server (NTRS)

Vachon, M. Jake; Ray, Ronald J.; Walsh, Kevin R.; Ennix, Kimberly

2003-01-01

The Autonomous Formation Flight (AFF) project at the NASA Dryden Flight Research Center (Edwards, California) investigated performance benefits resulting from formation flight, such as reduced aerodynamic drag and fuel consumption. To obtain data on performance benefits, a trailing F/A-18 airplane flew within the wing tip-shed vortex of a leading F/A-18 airplane. The pilot of the trail airplane used advanced station-keeping technology to aid in positioning the trail airplane at precise locations behind the lead airplane. The specially instrumented trail airplane was able to obtain accurate fuel flow measurements and to calculate engine thrust and vehicle drag. A maneuver technique developed for this test provided a direct comparison of performance values while flying in and out of the vortex. Based on performance within the vortex as a function of changes in vertical, lateral, and longitudinal positioning, these tests explored design-drivers for autonomous stationkeeping control systems. Observations showed significant performance improvements over a large range of trail positions tested. Calculations revealed maximum drag reductions of over 20 percent, and demonstrated maximum reductions in fuel flow of just over 18 percent.

Absence of jamming in ant trails: feedback control of self-propulsion and noise.

PubMed

Chaudhuri, Debasish; Nagar, Apoorva

2015-01-01

We present a model of ant traffic considering individual ants as self-propelled particles undergoing single-file motion on a one-dimensional trail. Recent experiments on unidirectional ant traffic in well-formed natural trails showed that the collective velocity of ants remains approximately unchanged, leading to the absence of jamming even at very high densities [John et al., Phys. Rev. Lett. 102, 108001 (2009)]. Assuming a feedback control mechanism of self-propulsion force generated by each ant using information about the distance from the ant in front, our model captures all the main features observed in the experiment. The distance headway distribution shows a maximum corresponding to separations within clusters. The position of this maximum remains independent of average number density. We find a non-equilibrium first-order transition, with the formation of an infinite cluster at a threshold density where all the ants in the system suddenly become part of a single cluster.

Exposure to aged crumb rubber reduces survival time during a stress test in earthworms (Eisenia fetida).

PubMed

Pochron, Sharon; Nikakis, Jacqueline; Illuzzi, Kyra; Baatz, Andrea; Demirciyan, Loriana; Dhillon, Amritjot; Gaylor, Thomas; Manganaro, Alexa; Maritato, Nicholas; Moawad, Michael; Singh, Rajwinder; Tucker, Clara; Vaughan, Daniel

2018-04-01

Solid waste management struggles with the sustainable disposal of used tires. One solution involves shredding used tires into crumb rubber and using the material as infill for artificial turf. However, crumb rubber contains hydrocarbons, organic compounds, and heavy metals, and it travels into the environment. Earthworms living in soil contaminated with virgin crumb rubber gained 14% less body weight than did earthworms living in uncontaminated soil, but the impact of aged crumb rubber on the earthworms is unknown. Since many athletic fields contain aged crumb rubber, we compared the body weight, survivorship, and longevity in heat and light stress for earthworms living in clean topsoil to those living in topsoil contaminated with aged crumb rubber. We also characterized levels of metals, nutrients, and micronutrients of both soil treatments and compared those to published values for soil contaminated with virgin crumb rubber. Consistent with earlier research, we found that contaminated soil did not inhibit microbial respiration rates. Aged crumb rubber, like new crumb rubber, had high levels of zinc. However, while exposure to aged crumb rubber did not reduce earthworm body weight as did exposure to new crumb rubber, exposure to aged crumb rubber reduced earthworm survival time during a stress test by a statistically significant 38 min (16.2%) relative to the survival time for worms that had lived in clean soil. Aged crumb rubber and new crumb rubber appear to pose similar toxic risks to earthworms. This study suggests an environmental cost associated with the current tire-recycling solution.

LES of High-Reynolds-Number Coanda Flow Separating from a Rounded Trailing Edge of a Circulation Control Airfoil

NASA Technical Reports Server (NTRS)

Nichino, Takafumi; Hahn, Seonghyeon; Shariff, Karim

2010-01-01

This slide presentation reviews the Large Eddy Simulation of a high reynolds number Coanda flow that is separated from a round trailing edge of a ciruclation control airfoil. The objectives of the study are: (1) To investigate detailed physics (flow structures and statistics) of the fully turbulent Coanda jet applied to a CC airfoil, by using LES (2) To compare LES and RANS results to figure out how to improve the performance of existing RANS models for this type of flow.

The Effectiveness at High Speeds of a 20-Percent-chord Plain Trailing-edge Flap on the NACA 65-210 Airfoil Section

NASA Technical Reports Server (NTRS)

Stivers, Louis S., Jr.

1947-01-01

An analysis has been made of the lift-control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flag on the INCA 65-210 airfoil section.

Diversity of Mosquitoes (Diptera: Culicidae) Attracted to Human Subjects in Rubber Plantations, Secondary Forests, and Villages in Luang Prabang Province, Northern Lao PDR.

PubMed

Tangena, Julie-Anne A; Thammavong, Phoutmany; Malaithong, Naritsara; Inthavong, Thavone; Ouanesamon, Phuthasone; Brey, Paul T; Lindsay, Steve W

2017-11-07

The impact of the rapid expansion of rubber plantations in South-East Asia on mosquito populations is uncertain. We compared the abundance and diversity of adult mosquitoes using human-baited traps in four typical rural habitats in northern Lao PDR: secondary forests, immature rubber plantations, mature rubber plantations, and villages. Generalized estimating equations were used to explore differences in mosquito abundance between habitats, and Simpson's diversity index was used to measure species diversity. Over nine months, 24,927 female mosquitoes were collected, including 51 species newly recorded in Lao PDR. A list of the 114 mosquito species identified is included. More mosquitoes, including vector species, were collected in the secondary forest than immature rubber plantations (rainy season, odds ratio [OR] 0.33, 95% confidence interval [CI] 0.31-0.36; dry season, 0.46, 95% CI 0.41-0.51), mature rubber plantations (rainy season, OR 0.25, 95% CI 0.23-0.27; dry season, OR 0.25, 95% CI 0.22-0.28), and villages (rainy season, OR 0.13, 95% CI 0.12-0.14; dry season, 0.20, 95% CI 0.18-0.23). All habitats showed high species diversity (Simpson's indexes between 0.82-0.86) with vectors of dengue, Japanese encephalitis (JE), lymphatic filariasis, and malaria. In the secondary forests and rubber plantations, Aedes albopictus (Skuse), a dengue vector, was the dominant mosquito species, while in the villages, Culex vishnui (Theobald), a JE vector, was most common. This study has increased the overall knowledge of mosquito fauna in Lao PDR. The high abundance of Ae. albopictus in natural and man-made forests warrants concern, with vector control measures currently only implemented in cities and villages. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Calibration of silicone rubber rods as passive samplers for pesticides at two different flow velocities: Modeling of sampling rates under water boundary layer and polymer control.

PubMed

Martin, Alexis; Margoum, Christelle; Jolivet, Antoine; Assoumani, Azziz; El Moujahid, Bachir; Randon, Jérôme; Coquery, Marina

2018-04-01

There is a need to determine time-weighted average concentrations of polar contaminants such as pesticides by passive sampling in environmental waters. Calibration data for silicone rubber-based passive samplers are lacking for this class of compounds. The calibration data, sampling rate (R s ), and partition coefficient between silicone rubber and water (K sw ) were precisely determined for 23 pesticides and 13 candidate performance reference compounds (PRCs) in a laboratory calibration system over 14 d for 2 water flow velocities, 5 and 20 cm s -1 . The results showed that an in situ exposure duration of 7 d left a silicone rubber rod passive sampler configuration in the linear or curvilinear uptake period for 19 of the pesticides studied. A change in the transport mechanism from polymer control to water boundary layer control was observed for pesticides with a log K sw of approximately 3.3. The PRC candidates were not fully relevant to correct the impact of water flow velocity on R s . We therefore propose an alternative method based on an overall resistance to mass transfer model to adjust R s from laboratory experiments to in situ hydrodynamic conditions. We estimated diffusion coefficients (D s ) and thickness of water boundary layer (δ w ) as adjustable model parameters. Log D s values ranged from -12.13 to -10.07 m 2  s -1 . The estimated δ w value showed a power function correlation with water flow velocity. Environ Toxicol Chem 2018;37:1208-1218. © 2017 SETAC. © 2017 SETAC.

Body ownership and attention in the mirror: insights from somatoparaphrenia and the rubber hand illusion.

PubMed

Jenkinson, Paul M; Haggard, Patrick; Ferreira, Nicola C; Fotopoulou, Aikaterini

2013-07-01

The brain receives and synthesises information about the body from different modalities, coordinates and perspectives, and affords us with a coherent and stable sense of body ownership. We studied this sense in a somatoparaphrenic patient and three control patients, all with unilateral right-hemisphere lesions. We experimentally manipulated the visual perspective (direct- versus mirror-view) and spatial attention (drawn to peripersonal space versus extrapersonal space) in an experiment involving recognising one's own hand. The somatoparaphrenic patient denied limb ownership in all direct view trials, but viewing the hand via a mirror significantly increased ownership. The extent of this increase depended on spatial attention; when attention was drawn to the extrapersonal space (near-the-mirror) the patient showed a near perfect recognition of her arm in the mirror, while when attention was drawn to peripersonal space (near-the-body) the patient recognised her arm in only half the mirror trials. In a supplementary experiment, we used the Rubber Hand Illusion to manipulate the same factors in healthy controls. Ownership of the rubber hand occurred in both direct and mirror view, but shifting attention between peripersonal and extrapersonal space had no effect on rubber-hand ownership. We conclude that the isolation of visual perspectives on the body and the division of attention between two different locations is not sufficient to affect body ownership in healthy individuals and right hemisphere controls. However, in somatoparaphrenia, where first-person body ownership and stimulus-driven attention are impaired by lesions to a right-hemisphere ventral attentional-network, the body can nevertheless be recognised as one's own if perceived in a third-person visual perspective and particularly if top-down, spatial attention is directed away from peripersonal space. Copyright © 2013 Elsevier Ltd. All rights reserved.

Nonaqueous ozonation of vulcanized rubber

DOEpatents

Serkiz, Steven M.

1999-01-01

A process and resulting product is provided in which a solid particulate, such as vulcanized crumb rubber, has the surface functional groups oxidized by ozonation using a nonpolar solvent. The ozonation process renders the treated crumb rubber more suitable for use in new rubber formulations. As a result, larger loading levels of the treated crumb rubber can be used in new rubber mixtures.

Comparative studies on crosslinked and uncrosslinked natural rubber biodegradation by Pseudomonas sp.

PubMed

Roy, Ram Vinod; Das, Mithu; Banerjee, Rintu; Bhowmick, Anil K

2006-12-01

A comparative study on biodegradation of di-cumyl peroxide (DCP) crosslinked and uncrosslinked natural rubber by Pseudomonas sp. was carried out. Decrease in organic carbon content along with the changes in tensile strength of the treated rubber, both DCP crosslinked and uncrosslinked natural rubber, indicated rubber hydrocarbon utilization by the Pseudomonas sp. A decrease in 60.88% MPa and 41.66% MPa was observed after five month's old treated uncrosslinked natural rubber and DCP crosslinked rubber, respectively. Biodegradation was more pronounced in natural uncrosslinked rubber, which was further confirmed by the formation of aldehydic compounds with decrease in CH2 stretching frequencies.

Effect of superhydrophobicity on surface damage of silicone rubber under AC voltage

NASA Astrophysics Data System (ADS)

Li, Yufeng; Jin, Haiyun; Nie, Shichao; Tong, Cheng; Gao, Naikui

2018-03-01

In this paper, the influence of superhydrophobicity on the surface damage of silicone rubber is studied. On a common silicone rubber surface, a droplet can become elongated, and arc discharge induced by the droplet can cause tracking on the silicone rubber surface. However, for a superhydrophobic silicone rubber surface, a droplet can leave the silicone rubber due to the low adhesion of the superhydrophobic surface. Accordingly, arc discharge caused by the droplet does not occur, and the surface of the silicone rubber is not affected. Results demonstrate that using a superhydrophobic surface has a significant effect on limiting the surface damage of silicone rubber.

MRI and Neuropsychological Correlates in African Americans with Hypertension and left vEntricular Hypertrophy.

PubMed

Waldron-Perrine, B; Kisser, J E; Brody, A; Haacke, E M; Dawood, R; Millis, S; Levy, P

2018-04-17

African Americans (AA) are at high risk for hypertension (HTN) and poor blood pressure (BP) control. Persistently elevated BP contributes to cardiovascular morbidity. White matter hyperintensities (WMH) are a definable magnetic resonance imaging (MRI) marker of cerebrovascular injury linked to impairments in higher level thinking (i.e., executive functions), memory formation and speed of perceptual-motor processing. This sub-investigation evaluated neuropsychological functioning in association with WMH on brain MRIs in 23 otherwise healthy hypertensive AAs participating in an NIH-funded study of the effects of Vitamin D on BP and cardiac remodeling in AA patients 30-74 years of age with HTN and left ventricular hypertrophy. Neuropsychological assessment included psychomotor processing speed [(Symbol Digit Modality Test (SDMT) and Trail Making Test], executive functioning (Controlled Oral Word Association Test and Trail Making Test Part B), memory (Rey Auditory Verbal Learning Test), and fine motor functioning (Finger Tapping). Significant correlations (p< .05) were found between volume of periventricular lesions and Trails A (r = .51) and dominant hand finger tapping speed (r = -.69) and between subcortical lesion volume and Trails A (r = .60), both dominant (r = -.62) and non-dominant hand finger tapping speed (r = -.76) and oral SDMT (r = -.60); higher lesion volumes correlated to worse neuropsychological performance. Psychomotor tests including the Trail Making Test and finger tapping speed are sensitive indicators of subclinical deficits in mental processing speed and could serve as early markers of deep subcortical cerebrovascular injury in otherwise-healthy individuals with uncontrolled chronic HTN.

Advances in rubber/halloysite nanotubes nanocomposites.

PubMed

Jia, Zhixin; Guo, Baochun; Jia, Demin

2014-02-01

The research advances in rubber/halloysite nanotubes (rubber/HNTs) nanocomposites are reviewed. HNTs are environmentally-friendly natural nanomaterials, which could be used to prepare the rubber-based nanocomposites with high performance and low cost. Unmodified HNTs could be adopted to prepare the rubber/HNTs composites with improved mechanical properties, however, the rubber/HNTs nanocomposites with fine morphology and excellent properties were chiefly prepared with various modifiers by in situ mixing method. A series of rubber/HNTs nanocomposites containing several rubbers (SBR, NR, xSBR, NBR, PU) and different modifiers (ENR, RH, Si69, SA, MAA, ILs) have been investigated. The results showed that all the rubber/HNTs nanocomposites achieved strong interfacial interaction via interfacial covalent bonds, hydrogen bonds or multiple interactions, realized significantly improved dispersion of HNTs at nanoscale and exhibited excellent mechanical performances and other properties.

Modern Control Aspects of Automatically Steered Vehicles

DOT National Transportation Integrated Search

1971-12-01

In the study of automatically steered rubber tired vehicles, little emphasis in the past has been placed on the steering control laws. The report examines the control law problem from the state variable point of view and it is shown that, except for ...

Transonic Drag Reduction Through Trailing-Edge Blowing on the FAST-MAC Circulation Control Model

NASA Technical Reports Server (NTRS)

Chan, David T.; Jones, Gregory S.; Milholen, William E., II; Goodliff, Scott L.

2017-01-01

A third wind tunnel test of the FAST-MAC circulation control semi-span model was completed in the National Transonic Facility at the NASA Langley Research Center where the model was configured for transonic testing of the cruise configuration with 0deg flap detection to determine the potential for transonic drag reduction with the circulation control blowing. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged ap. Recent upgrades to transonic semi-span flow control testing at the NTF have demonstrated an improvement to overall data repeatability, particularly for the drag measurement, that allows for increased confidence in the data results. The static thrust generated by the blowing slot was removed from the wind-on data using force and moment balance data from wind-o thrust tares. This paper discusses the impact of the trailing-edge blowing to the transonic aerodynamics of the FAST-MAC model in the cruise configuration, where at flight Reynolds numbers, the thrust-removed corrected data showed that an overall drag reduction and increased aerodynamic efficiency was realized as a consequence of the blowing.

The effect of high concentration potassium permanganate on protein contamination from metallic and synthetic rubber airway equipment.

PubMed

Laupu, W; Brimacombe, J

2007-08-01

We tested the hypothesis that supplementary cleaning using potassium permanganate 8 mg.l(-1) eliminates protein deposits from the reusable metallic and synthetic rubber airway equipment. Twenty Macintosh laryngoscope blades (surgical steel), 20 pairs of Magill's forceps (surgical steel) and 20 Guedel airways (synthetic rubber) were allocated to two groups for supplementary cleaning. In group A, the device was immersed in potassium permanganate 8 mg.l(-1). In group B (controls), the device was immersed in sterile water. The devices were then immersed in a protein staining solution, rinsed and the severity of staining was scored. In addition, the devices were inspected for tissue and then tested for occult blood. Protein contamination was lower in the potassium permanganate group for all devices (each device: p < 0.0001). There was no staining detected in the permanganate group. In the permanganate group, dried tissue was detected in the teeth of one pair of forceps, which was not detected following supplementary cleaning. Additionally, occult blood was detected on two pairs of forceps and a laryngoscope blade, which was not detected following supplementary cleaning. In the control group, no tissue was detected but one pair of forceps and two laryngoscope blades tested positive for occult blood before and after supplementary cleaning. We conclude that supplementary cleaning using potassium permanganate 8 mg.l(-1) eliminates protein deposits from re-usable metallic and synthetic rubber airway equipment.

Geospatial application for the identification and monitoring of rubber smallholders in the Malaysian state of Negeri Sembilan

NASA Astrophysics Data System (ADS)

Hafiz Mohd Hazir, Mohd; Muda, Tuan Mohamad Tuan

2016-06-01

The Malaysian rubber industry, especially in the upstream sector, is much dependent on smallholders to produce latex or cup lumps. Identification and monitoring of rubber smallholders are essential tasks when it comes to the Malaysian rubber industry's sustainability. The authorised agencies who support the rubber smallholders can do better planning, arranging, and managing. This paper introduces a method of calculating the total number of smallholders as well as identifying the location of their planted rubber area. The scope of this study only focused on land owners as rubber smallholders in the selected study area of Negeri Sembilan. The land use map provided by the Department of Agriculture Malaysia gave information on distribution of rubber area in Malaysia, while the cadastral map from the Department of Survey and Mapping Malaysia was specifically used for identifying land owners of each rubber parcel or rubber lot. Both data were analyzed and processed with ArcGIS software to extract the information, and the results were then compared to the Malaysian Rubber Board smallholders database.

Development and demonstration of a flutter-suppression system using active controls. [wind tunnel tests

NASA Technical Reports Server (NTRS)

Sandford, M. C.; Abel, I.; Gray, D. L.

1975-01-01

The application of active control technology to suppress flutter was demonstrated successfully in the transonic dynamics tunnel with a delta-wing model. The model was a simplified version of a proposed supersonic transport wing design. An active flutter suppression method based on an aerodynamic energy criterion was verified by using three different control laws. The first two control laws utilized both leading-edge and trailing-edge active control surfaces, whereas the third control law required only a single trailing-edge active control surface. At a Mach number of 0.9 the experimental results demonstrated increases in the flutter dynamic pressure from 12.5 percent to 30 percent with active controls. Analytical methods were developed to predict both open-loop and closed-loop stability, and the results agreed reasonably well with the experimental results.

Experimental evaluation of the certification-trail method

NASA Technical Reports Server (NTRS)

Sullivan, Gregory F.; Wilson, Dwight S.; Masson, Gerald M.; Itoh, Mamoru; Smith, Warren W.; Kay, Jonathan S.

1993-01-01

Certification trails are a recently introduced and promising approach to fault-detection and fault-tolerance. A comprehensive attempt to assess experimentally the performance and overall value of the method is reported. The method is applied to algorithms for the following problems: huffman tree, shortest path, minimum spanning tree, sorting, and convex hull. Our results reveal many cases in which an approach using certification-trails allows for significantly faster overall program execution time than a basic time redundancy-approach. Algorithms for the answer-validation problem for abstract data types were also examined. This kind of problem provides a basis for applying the certification-trail method to wide classes of algorithms. Answer-validation solutions for two types of priority queues were implemented and analyzed. In both cases, the algorithm which performs answer-validation is substantially faster than the original algorithm for computing the answer. Next, a probabilistic model and analysis which enables comparison between the certification-trail method and the time-redundancy approach were presented. The analysis reveals some substantial and sometimes surprising advantages for ther certification-trail method. Finally, the work our group performed on the design and implementation of fault injection testbeds for experimental analysis of the certification trail technique is discussed. This work employs two distinct methodologies, software fault injection (modification of instruction, data, and stack segments of programs on a Sun Sparcstation ELC and on an IBM 386 PC) and hardware fault injection (control, address, and data lines of a Motorola MC68000-based target system pulsed at logical zero/one values). Our results indicate the viability of the certification trail technique. It is also believed that the tools developed provide a solid base for additional exploration.

Economic status, smoking, occupational exposure to rubber, and lung cancer: a case-cohort study.

PubMed

Li, Ke; Yu, Shunzhang

2002-05-01

Recent studies tend consistently to confirm the presence of a moderate excess risk of lung cancer in the rubber industry. However, the agent responsible for the excess of lung cancer is still obscure. Also, analyses without regard to the modifying effects of sex, economic status, and smoking habit are less than satisfactory. To explore these questions, we have conducted a case-cohort study using the data of 51 lung cancer deaths in 1973-1997 and a random sample (sub-cohort) of 188 from among 1598 subjects in a rubber factory in Shanghai, China. We computed the risks of lung cancer by economic status, smoking habit, coal fumes in home, and year of first employment. We assessed lung cancer risks for occupational exposures, unadjusted and adjusted for economic status and smoking. After confounding effects of smoking and economic status were controlled, we found that rate ratios were 1.43 (95% confidence interval (CI) 0.43-4.69), 1.79 (95% CI 0.64-5.03), and 3.76 (95% CI 1.44-9.86) for 1-14, 15-29, and 30-45 exposure-years in curing department, respectively. The data showed significant trends in increased risk of lung cancer with duration of exposure in tire-curing department (score test for trend:, P = 0.004). However, in front rubber processing (weighing and mixing, calendering, extruding, and milling), no significant excess risk of lung cancer was found. If it can be confirmed that nitrosamines are mainly generated in back rubber processing (curing and vulcanizing), it would be reasonable to conclude that excess risk of lung cancer in rubber industry is attributable, at least partially, to exposure to nitrosamines.

Electrospinning of PVC with natural rubber

NASA Astrophysics Data System (ADS)

Othman, Muhammad Hariz; Mohamed, Mahathir; Abdullah, Ibrahim

2013-11-01

Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber's mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphology and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber.

40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber subcategory...

40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber subcategory...

21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by the...

Effect of non-rubber constituents on Guayule and Hevea rubber intrinsic properties

USDA-ARS?s Scientific Manuscript database

To meet the increasing demand for natural rubber (NR), currently sourced from the tropical rubber tree Hevea brasiliensis, and address price volatility and steadily increasing labor costs, alternate rubber-producing species are in commercial development. One of these, guayule (Parthenium argentatum)...

Mechanical Behavior and Fatigue Studies of Rubber Components Used in Tracked Vehicles

DTIC Science & Technology

2010-08-17

durability to this elastomers and polybutadiene is rubber , which gives rubber -like properties. SBR has good abrasion resistance and good aging ...SIMULATION, TESTING AND VALIDATION (MSTV) MINI-SYMPOSIUM AUGUST 17-19 DEARBORN, MICHIGAN MECHANICAL BEHAVIOR AND FATIGUE STUDIES OF RUBBER COMPONENTS USED...Analytics Group US Army TARDEC Warren, MI ABSTRACT In this study, a styrene butadiene rubber , which is similar to the rubber used in road wheel

N2O emissions in tropical rainforest and rubber plantation, the indicator from landuse changing in Xishuangbanna, Southwest China

NASA Astrophysics Data System (ADS)

Zhou, W. J.; Zhu, J.; Ji, H. L.; Zhang, Y.; Zhang, J.; Zheng, X.

2016-12-01

To understand the effects of landuse on N2O emissions and local climate change in the tropics, we measured N2O fluxes from a primary tropical rainforest (TRF, with treatments of litter removal and control) and a fertilized rubber plantation (RP, with treatments of fertilization (75 kg N ha-1 yr-1) and unfertilization) at Xishuangbanna, southwest China since 2012. The results have shown: 1) Fertilized RP N2O emission is bimodel, one peak after dry season fertilizer, another after rainy season fertilizer. Otherwise, the unfertilized RP and TRF have the similar seasonal dynamic with one peak in the middle of rainy season. 2) due to the fertilizer influence, the poaitive correlation between soil temperature/soil moisture and N2O was more significantly in unfertilized RP than fertilized RP respectively litter input changed the dominated controller of N2O emission in TRF: litter carbon input and soil DOC content for control treatment and, soil temperature and soil NO3- -N for litter removal treatment. 3) lab incubation indicated denitrification and nitrification as the main source for N2O emission in TRF and RP, respectively. 4) The N2O emissions from the fertilized and unfertilized plots in RP were 4.0 and 2.5 kg N ha-1 yr-1, respectively, from control and litter removal plots in TRF were 0.48 and 0.32 kg N ha-1 yr-1,respectively. 5) 100-year carbon dioxide equivalence of N2O from fertilized RP offsets 5.8% and 31.5% of carbon sink of the rubber plantation and local TRF, respectively. Upscaling it to the whole Xishuangbanna, N2O emissions from fertilized RP offset 17.1% of the tropical rainforest's carbon sink. When tropical rainforests are converted to fertilized rubber plantations, the N2O emission seasonal dynamic and mechanisms changed, the global warming effect is enhanced.

N2O emissions in tropical rainforest and rubber plantation, the indicator from landuse changing in Xishuangbanna, Southwest China

NASA Astrophysics Data System (ADS)

Zhou, Wenjun; Zhu, Jing; Ji, Hong-li; Zhang, Yi-Ping; Sha, Li-Qing; Gao, Jin-Bo; Zhang, Jun-Hui; Zheng, Xunhua

2017-04-01

To understand the effects of landuse on N2O emissions and local climate change in the tropics, we measured N2O fluxes from a primary tropical rainforest (TRF, with treatments of litter removal and control) and a fertilized rubber plantation (RP, with treatments of fertilization (75 kg N ha-1 yr-1) and unfertilization) at Xishuangbanna, southwest China since 2012. The results have shown: 1) Fertilized RP N2O emission is bimodel, one peak after dry season fertilizer, another after rainy season fertilizer. Otherwise, the unfertilized RP and TRF have the similar seasonal dynamic with one peak in the middle of rainy season. 2) due to the fertilizer influence, the poaitive correlation between soil temperature/soil moisture and N2O was more significantly in unfertilized RP than fertilized RP respectively litter input changed the dominated controller of N2O emission in TRF: litter carbon input and soil DOC content for control treatment and, soil temperature and soil NO3- -N for litter removal treatment. 3) lab incubation indicated denitrification and nitrification as the main source for N2O emission in TRF and RP, respectively. 4) The N2O emissions from the fertilized and unfertilized plots in RP were 4.0 and 2.5 kg N ha-1 yr-1, respectively, from control and litter removal plots in TRF were 0.48 and 0.32 kg N ha-1 yr-1,respectively. 5) 100-year carbon dioxide equivalence of N2O from fertilized RP offsets 5.8% and 31.5% of carbon sink of the rubber plantation and local TRF, respectively. Upscaling it to the whole Xishuangbanna, N2O emissions from fertilized RP offset 17.1% of the tropical rainforest's carbon sink. When tropical rainforests are converted to fertilized rubber plantations, the N2O emission seasonal dynamic and mechanisms changed, the global warming effect is enhanced.

Utilization of the cellular stress response to sensitize cancer cells to TRAIL-mediated apoptosis.

PubMed

Siegelin, Markus David

2012-08-01

Tumor necrosis factor-related apoptosis inducing ligand (TRAIL) is a promising death ligand who has received significant attention due to its specific anti-cancer activity. Recently, a number of clinical trials involving either recombinant soluble TRAIL or agonistic death receptor (DR) antibodies have even been initiated. One major caveat in TRAIL-based anti-cancer therapies is that a considerable number of cancer cells are notorious resistant to apoptosis induction by TRAIL. Overcoming this primary or secondary evolved resistance is an utmost important goal of present cancer research. The current literature suggests that TRAIL resistance is mediated by a number of endogenous factors. According to recent research, stress-related transcription factors have acquired a pivotal role in the sensitization of highly resistant cancer cells, for example, pancreatic cancer and glioblastoma cells, to TRAIL-mediated cell death. Out of this transcription factor family, C/EBP-homologous protein (CHOP) is linked to the control of DR-mediated apoptosis by modulation of several apoptotic and anti-apoptotic factors. Stress responses in certain organelles, such as endoplasmic reticulum (ER) and mitochondria, are potent inductors of CHOP expression. This report focuses on the influence of stress responses on endogenous or acquired resistance to extrinsic apoptosis in tumor cells and summarizes recent findings and results. The Medline and ClinicalTrials database with key words were used for this review. A potential novel treatment strategy for highly treatment-resistant tumors is the induction of a cellular stress response in cancer cells. The induction of an organelle-related stress response, such as nuclear, ER and mitochondrial stress, leads to a dramatic sensitization of a broad variety of cancer cells of different tumor entities to the apoptotic ligand, TRAIL. Importantly, non-neoplastic cells are not sensitized to TRAIL-mediated cell death through the unfolded protein response in most instances, suggesting that this treatment is not only of high efficacy, but even more less of unwanted toxicity in patients.

Investigating the Improved Aerodynamic Efficiency of Cambered Frames on Membrane MAV Wings

NASA Astrophysics Data System (ADS)

Wrist, Andrew; Zhang, Zheng; Hubner, Paul

2014-11-01

Previous research has demonstrated that membrane wings with cambered frames are more aerodynamically efficient than those with flat frames, despite passive dynamic membrane cambering for both. To help understand this aerodynamic benefit, this study compares the time-averaged membrane shape as well as membrane vibration frequency and amplitude for a group of wings with cambered frames. The frames were 3D printed with a hardened polymer material, and a silicon rubber membrane was attached to the top surface. The frame aspect ratio is two, comprised of two cells each with a cell aspect ratio of one. The rigid leading edge extended 20% of the chord, and the trailing edge was scalloped at 25%. Camber ranged from 2--6%, camber location from 40--60%, and airfoil thickness from 4--6%. Tests were performed in the University of Alabama's MAV wind tunnel at 10 m/s (Re = 50,000). High speed imaging results of the deformation and vibration will be discussed in context to airfoil and wing theory. National Science Foundation Grant Number: 1358991.

Reinforcement effect of soy protein nanoparticles in amine-modified natural rubber latex

USDA-ARS?s Scientific Manuscript database

Mechanical properties of natural rubber reinforced with soy protein nanoparticles are useful for various rubber applications. However, the properties is further improved by improving interactions between soy protein and rubber. A novel method is used to modify particle surface of natural rubber late...

Particle reinforced composites from acrylamide modified blend of styrene-butadiene and natural rubber

USDA-ARS?s Scientific Manuscript database

Blends of styrene-butadiene rubber and natural rubber that provide balanced properties were modified with acrylamide and reinforced with soy protein particles. The rubber composites show improved mechanical properties. Both modified rubber and composites showed a faster curing rate. The crosslinking...

Method for the addition of vulcanized waste rubber to virgin rubber products

DOEpatents

Romine, Robert A.; Snowden-Swan, Lesley J.

1997-01-01

The invention is a method of using enzymes from thiophyllic microbes for selectively breaking the sulfur rubber cross-link bonds in vulcanized rubber. The process is halted at the sulfoxide or sulfone step so that a devulcanized layer is reactive with virgin rubber.

Method for the addition of vulcanized waste rubber to virgin rubber products

DOEpatents

Romine, R.A.; Snowden-Swan, L.J.

1997-01-28

The invention is a method of using enzymes from thiophyllic microbes for selectively breaking the sulfur rubber cross-link bonds in vulcanized rubber. The process is halted at the sulfoxide or sulfone step so that a devulcanized layer is reactive with virgin rubber. 8 figs.

The functional analyses of the cis-prenyltransferase and the rubber elongation factor in rubber biosynthesis

USDA-ARS?s Scientific Manuscript database

Natural rubber (cis-1,4-polyisoprene) is an essential plant derived commodity required for the manufacture of numerous industrial, medical and household items. Rubber is synthesized and sequestered on cytsolic vesicles known as rubber particles. When provided with farnesyl pyrophosphate (FPP) and is...

Chlorinated rubbers with advanced properties for tire industry

NASA Astrophysics Data System (ADS)

Mikhaylov, I. A.; Sukhareva, K. V.; Andriasyan, Yu. O.; Popov, A. A.

2017-12-01

The paper investigates the production and processing of halide-modified chlorinated rubbers, such as isobutylene isoprene rubber and ethylene-propylene-diene-monomer rubber (IIR and EPDM), which are perspective in terms of application in rubber industry. Prospects for their production and application are determined by the specific properties of these rubbers (low gas permeability of IIR, high heat and ozone resistance of EPDM). These properties are governed by the structure of both initial IIR and EPDM and chlorinated rubbers (ChIIR and ChEPDM). A new alternative technology of obtaining chlorinated elastomers based on solid-phase mechanochemical halide modification is proposed. Novel chlorinated polyolefin rubbers obtained by the developed technology show good technological properties under industrial production conditions due to enhanced covulcanization.

Electrospinning of PVC with natural rubber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Othman, Muhammad Hariz; Abdullah, Ibrahim; Mohamed, Mahathir

Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber’s mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphologymore » and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber.« less

Microbial detoxification of waste rubber material by wood-rotting fungi.

PubMed

Bredberg, Katarina; Andersson, B Erik; Landfors, Eva; Holst, Olle

2002-07-01

The extensive use of rubber products, mainly tires, and the difficulties to recycle those products, has resulted in world wide environmental problems. Microbial devulcanisation is a promising way to increase the recycling of rubber materials. One obstacle is that several microorganisms tested for devulcanisation are sensitive to rubber additives. A way to overcome this might be to detoxify the rubber material with fungi prior to the devulcanisation. In this study, 15 species of white-rot and brown-rot fungi have been screened with regard to their capacity to degrade an aromatic model compound in the presence of ground waste tire rubber. The most effective fungus, Resinicium bicolor, was used for detoxification of rubber material. Increase in growth of the desulfurising bacterium Thiobacillus ferrooxidans in presence of the rubber treated with Resinicium bicolor compared to untreated rubber demonstrated that detoxification with fungi is possible.

Effects of forests, roads and mistletoe on bird diversity in monoculture rubber plantations

NASA Astrophysics Data System (ADS)

Sreekar, Rachakonda; Huang, Guohualing; Yasuda, Mika; Quan, Rui-Chang; Goodale, Eben; Corlett, Richard T.; Tomlinson, Kyle W.

2016-02-01

Rising global demand for natural rubber is expanding monoculture rubber (Hevea brasilensis) at the expense of natural forests in the Old World tropics. Conversion of forests into rubber plantations has a devastating impact on biodiversity and we have yet to identify management strategies that can mitigate this. We determined the life-history traits that best predict bird species occurrence in rubber plantations in SW China and investigated the effects of surrounding forest cover and distance to roads on bird diversity. Mistletoes provide nectar and fruit resources in rubber so we examined mistletoe densities and the relationship with forest cover and rubber tree diameter. In rubber plantations, we recorded less than half of all bird species extant in the surrounding area. Birds with wider habitat breadths and low conservation value had a higher probability of occurrence. Species richness and diversity increased logarithmically with surrounding forest cover, but roads had little effect. Mistletoe density increased exponentially with rubber tree diameters, but was unrelated to forest cover. To maximize bird diversity in rubber-dominated landscapes it is therefore necessary to preserve as much forest as possible, construct roads through plantations and not forest, and retain some large rubber trees with mistletoes during crop rotations.

Effects of forests, roads and mistletoe on bird diversity in monoculture rubber plantations.

PubMed

Sreekar, Rachakonda; Huang, Guohualing; Yasuda, Mika; Quan, Rui-Chang; Goodale, Eben; Corlett, Richard T; Tomlinson, Kyle W

2016-02-23

Rising global demand for natural rubber is expanding monoculture rubber (Hevea brasilensis) at the expense of natural forests in the Old World tropics. Conversion of forests into rubber plantations has a devastating impact on biodiversity and we have yet to identify management strategies that can mitigate this. We determined the life-history traits that best predict bird species occurrence in rubber plantations in SW China and investigated the effects of surrounding forest cover and distance to roads on bird diversity. Mistletoes provide nectar and fruit resources in rubber so we examined mistletoe densities and the relationship with forest cover and rubber tree diameter. In rubber plantations, we recorded less than half of all bird species extant in the surrounding area. Birds with wider habitat breadths and low conservation value had a higher probability of occurrence. Species richness and diversity increased logarithmically with surrounding forest cover, but roads had little effect. Mistletoe density increased exponentially with rubber tree diameters, but was unrelated to forest cover. To maximize bird diversity in rubber-dominated landscapes it is therefore necessary to preserve as much forest as possible, construct roads through plantations and not forest, and retain some large rubber trees with mistletoes during crop rotations.

Adhesion International 1987. Proceedings of the Annual Meeting of the Adhesion Society, Inc. (10th) Held in Williamsburg, Virginia on 23-27 February 1987

DTIC Science & Technology

1987-01-01

Sons, New York, 1983). The Effect of Electrochemical Potentials on the Durability of Rubber /Metal Bonds in Sea Watert A. STEVENSON Materials...cohesive fracture through the rubber . As a control experiment, a set of new dry testpieces were cut at the bond to various depths-simulating the full...melts are a new class of adhesives. They are created to improve the heat performance of hot melts without losing the advantages of hot melts, for

EVALUATION OF GLOVEBOX GLOVES FOR EFFECTIVE PERMEATION CONTROL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korinko, P.

A research and development task was undertaken to determine the permeabilities of hydrogen and dry air through different polymeric glove materials that are used to maintain the integrity of glovebox secondary containment. Fifteen different glove samples were obtained from four different manufacturers and samples cut from these gloves were tested. The gloves included baseline butyl rubber, Viton{reg_sign}, Dupont{reg_sign} Hypalon{reg_sign}, polyurethane, as well as composite gloves. The testing indicated that all of the vendor's butyl rubber gloves and the Jung Viton{reg_sign} gloves performed comparably in both gases.

Characterization of MUDENG, a novel anti-apoptotic protein

PubMed Central

Choi, J-H; Lim, J-B; Wickramanayake, D D; Wagley, Y; Kim, J; Lee, H-C; Seo, H G; Kim, T-H; Oh, J-W

2016-01-01

MUDENG (Mu-2-related death-inducing gene, MuD) is revealed to be involved in cell death signaling. Astrocytes, the major glial cell type in the central nervous system, are a source of brain tumors. In this study, we examined MuD expression and function in human astroglioma cells. Stimulation of U251-MG cells with tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) resulted in a 40% decrease in cell viability and a 33% decrease in MuD protein levels, although not in MuD mRNA levels. To study the functional relevance of MuD expression, stable transfectants expressing high levels of MuD were generated. Stimulation of these transfectants with TRAIL resulted in enhanced cell survival (77% for stable and 46% for control transfectants). Depletion of MuD led to a marked reduction upon TRAIL stimulation in cell viability (22% in MuD-depleted cells and 54% in control cells). In addition, we observed that MuD depletion increased the susceptibility of the cells to TRAIL by enhancing the cleavage of caspase-3/-9 and BH3-interacting domain death agonist (Bid). A unique 25-kDa fragment of B-cell lymphoma 2 (Bcl-2) lacking BH4 was observed 60–180 min post TRAIL treatment in MuD-depleted cells, suggesting that Bcl-2 is converted from its anti-apoptotic form to the truncated pro-apoptotic form. Importantly, the TRAIL-mediated decrease in cell viability in MuD-depleted cells was abrogated upon Bid depletion, indicating that the role of MuD in apoptotic signaling takes place at the Bid and Bcl-2 junction. MuD localizes predominantly in the endoplasmic reticulum and partly in the mitochondria and its amounts are reduced 6 h post TRAIL stimulation, presumably via caspase-3-mediated MuD cleavage. Collectively, these results suggest that MuD, a novel signaling protein, not only possesses an anti-apoptotic function but may also constitute an important target for the design of ideal candidates for combinatorial treatment strategies for glioma cells. PMID:27136675

40 CFR 258.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; plastics and resins manufacturing; pulp and paper industry; rubber and miscellaneous plastic products... wastewater treatment plant, water supply treatment plant, or air pollution control facility exclusive of the... a wastewater treatment plant, water supply treatment plant, or air pollution control facility and...

Experimental and simulated control of lift using trailing edge devices

NASA Astrophysics Data System (ADS)

Cooperman, A.; Blaylock, M.; van Dam, C. P.

2014-12-01

Two active aerodynamic load control (AALC) devices coupled with a control algorithm are shown to decrease the change in lift force experienced by an airfoil during a change in freestream velocity. Microtabs are small (1% chord) surfaces deployed perpendicular to an airfoil, while microjets are pneumatic jets with flow perpendicular to the surface of the airfoil near the trailing edge. Both devices are capable of producing a rapid change in an airfoil's lift coefficient. A control algorithm for microtabs has been tested in a wind tunnel using a modified S819 airfoil, and a microjet control algorithm has been simulated for a NACA 0012 airfoil using OVERFLOW. In both cases, the AALC devices have shown the ability to mitigate the changes in lift during a gust.

In-Trail Procedure Air Traffic Control Procedures Validation Simulation Study

NASA Technical Reports Server (NTRS)

Chartrand, Ryan C.; Hewitt, Katrin P.; Sweeney, Peter B.; Graff, Thomas J.; Jones, Kenneth M.

2012-01-01

In August 2007, Airservices Australia (Airservices) and the United States National Aeronautics and Space Administration (NASA) conducted a validation experiment of the air traffic control (ATC) procedures associated with the Automatic Dependant Surveillance-Broadcast (ADS-B) In-Trail Procedure (ITP). ITP is an Airborne Traffic Situation Awareness (ATSA) application designed for near-term use in procedural airspace in which ADS-B data are used to facilitate climb and descent maneuvers. NASA and Airservices conducted the experiment in Airservices simulator in Melbourne, Australia. Twelve current operational air traffic controllers participated in the experiment, which identified aspects of the ITP that could be improved (mainly in the communication and controller approval process). Results showed that controllers viewed the ITP as valid and acceptable. This paper describes the experiment design and results.

Characterization of rubber particles and rubber chain elongation in Taraxacum koksaghyz

PubMed Central

2010-01-01

Background Natural rubber is a biopolymer with exceptional qualities that cannot be completely replaced using synthetic alternatives. Although several key enzymes in the rubber biosynthetic pathway have been isolated, mainly from plants such as Hevea brasiliensis, Ficus spec. and the desert shrub Parthenium argentatum, there have been no in planta functional studies, e.g. by RNA interference, due to the absence of efficient and reproducible protocols for genetic engineering. In contrast, the Russian dandelion Taraxacum koksaghyz, which has long been considered as a potential alternative source of low-cost natural rubber, has a rapid life cycle and can be genetically transformed using a simple and reliable procedure. However, there is very little molecular data available for either the rubber polymer itself or its biosynthesis in T. koksaghyz. Results We established a method for the purification of rubber particles - the active sites of rubber biosynthesis - from T. koksaghyz latex. Photon correlation spectroscopy and transmission electron microscopy revealed an average particle size of 320 nm, and 13C nuclear magnetic resonance (NMR) spectroscopy confirmed that isolated rubber particles contain poly(cis-1,4-isoprene) with a purity >95%. Size exclusion chromatography indicated that the weight average molecular mass (w) of T. koksaghyz natural rubber is 4,000-5,000 kDa. Rubber particles showed rubber transferase activity of 0.2 pmol min-1 mg-1. Ex vivo rubber biosynthesis experiments resulted in a skewed unimodal distribution of [1-14C]isopentenyl pyrophosphate (IPP) incorporation at a w of 2,500 kDa. Characterization of recently isolated cis-prenyltransferases (CPTs) from T. koksaghyz revealed that these enzymes are associated with rubber particles and are able to produce long-chain polyprenols in yeast. Conclusions T. koksaghyz rubber particles are similar to those described for H. brasiliensis. They contain very pure, high molecular mass poly(cis-1,4-isoprene) and the chain elongation process can be studied ex vivo. Because of their localization on rubber particles and their activity in yeast, we propose that the recently described T. koksaghyz CPTs are the major rubber chain elongating enzymes in this species. T. koksaghyz is amenable to genetic analysis and modification, and therefore could be used as a model species for the investigation and comparison of rubber biosynthesis. PMID:20170509

Modeling no-jam traffic in ant trails: a pheromone-controlled approach

NASA Astrophysics Data System (ADS)

Guo, Ning; Hu, Mao-Bin; Jiang, Rui; Ding, Jianxun; Ling, Xiang

2018-05-01

The experiment in John et al (2009 Phys. Rev. Lett. 102 108001) shows that when ants move in a single-file trail, no jam emerges even at very high densities. We propose a self-propelled model of ant traffic to reproduce the fundamental diagram without a jammed branch. In this model, ants can adjust their desired velocities actively by perceiving pheromone concentration near the front of the trail. Moreover, ants will bear the repulsive force when they have physical contact with neighbors. The velocity in the simulation decreases slightly with increasing density, which captures the main feature observed in the experiment. Distributions of velocity and distance headway basically also conform to the experimental ones.

Construction of Pará rubber tree genome and multi-transcriptome database accelerates rubber researches.

PubMed

Makita, Yuko; Kawashima, Mika; Lau, Nyok Sean; Othman, Ahmad Sofiman; Matsui, Minami

2018-01-19

Natural rubber is an economically important material. Currently the Pará rubber tree, Hevea brasiliensis is the main commercial source. Little is known about rubber biosynthesis at the molecular level. Next-generation sequencing (NGS) technologies brought draft genomes of three rubber cultivars and a variety of RNA sequencing (RNA-seq) data. However, no current genome or transcriptome databases (DB) are organized by gene. A gene-oriented database is a valuable support for rubber research. Based on our original draft genome sequence of H. brasiliensis RRIM600, we constructed a rubber tree genome and transcriptome DB. Our DB provides genome information including gene functional annotations and multi-transcriptome data of RNA-seq, full-length cDNAs including PacBio Isoform sequencing (Iso-Seq), ESTs and genome wide transcription start sites (TSSs) derived from CAGE technology. Using our original and publically available RNA-seq data, we calculated co-expressed genes for identifying functionally related gene sets and/or genes regulated by the same transcription factor (TF). Users can access multi-transcriptome data through both a gene-oriented web page and a genome browser. For the gene searching system, we provide keyword search, sequence homology search and gene expression search; users can also select their expression threshold easily. The rubber genome and transcriptome DB provides rubber tree genome sequence and multi-transcriptomics data. This DB is useful for comprehensive understanding of the rubber transcriptome. This will assist both industrial and academic researchers for rubber and economically important close relatives such as R. communis, M. esculenta and J. curcas. The Rubber Transcriptome DB release 2017.03 is accessible at http://matsui-lab.riken.jp/rubber/ .

Cognitive Performance and Locomotor Adaptation in Persons With Anterior Cruciate Ligament Reconstruction.

PubMed

Stone, Amanda E; Roper, Jaimie A; Herman, Daniel C; Hass, Chris J

2018-05-01

Persons with anterior cruciate ligament reconstruction (ACLR) show deficits in gait and neuromuscular control following rehabilitation. This altered behavior extends to locomotor adaptation and learning, however the contributing factors to this observed behavior have yet to be investigated. The purpose of this study was to assess differences in locomotor adaptation and learning between ACLR and controls, and identify underlying contributors to motor adaptation in these individuals. Twenty ACLR individuals and 20 healthy controls (CON) agreed to participate in this study. Participants performed four cognitive and dexterity tasks (local version of Trail Making Test, reaction time test, electronic pursuit rotor test, and the Purdue pegboard). Three-dimensional kinematics were also collected while participants walked on a split-belt treadmill. ACLR individuals completed the local versions of Trails A and Trails B significantly faster than CON. During split-belt walking, ACLR individuals demonstrated smaller step length asymmetry during EARLY and LATE adaptation, smaller double support asymmetry during MID adaptation, and larger stance time asymmetry during DE-ADAPT compared with CON. ACLR individuals performed better during tasks that required visual attention and task switching and were less perturbed during split-belt walking compared to controls. Persons with ACLR may use different strategies than controls, cognitive or otherwise, to adapt locomotor patterns.

Chlorinolysis reclaims rubber of waste tires

NASA Technical Reports Server (NTRS)

Dufresne, E. R.; Tervet, J. H.; Hull, G. G.

1981-01-01

Process reclaims rubber and reduces sulfur content by using chlorine gas to oxidize sulfur bonds in preference to other bonds. Rubber does not have poor hysteresis and abrasion resistance like conventionally reclaimed rubber and is suitable for premium radial tires. Chlorinated rubber is less susceptible to swelling by oils and may be used as paint ingredient.

The role of the small rubber particle protein in determining rubber yields and polymer length in Russian dandelion

USDA-ARS?s Scientific Manuscript database

Several proteins have been identified and implicated in natural rubber biosynthesis, one of which, the small rubber particle protein (SRPP), was originally identified in Hevea brasiliensis as an abundant protein associated with cytosolic vesicles known as rubber particles. While previous in vitro s...

Comprehensive evaluation of the long-term performance of rubberized pavement, phase I : laboratory study of rubberized asphalt mix performance.

DOT National Transportation Integrated Search

2012-12-01

Crumb rubber, made from scrap tires, has been introduced into the production of different types of hot : mix asphalt (HMA) in either a wet or dry process. In the wet process, the crumb rubber and binder are : completely mixed to form asphalt rubber (...

21 CFR 872.6300 - Rubber dam and accessories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... center intended to isolate a tooth from fluids in the mouth during dental procedures, such as filling a... center. The device includes the rubber dam, rubber dam clamp, rubber dam frame, and forceps for a rubber... sexually transmitted diseases through oral sex; those devices are classified as condoms in § 884.5300 of...

21 CFR 872.6300 - Rubber dam and accessories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... center intended to isolate a tooth from fluids in the mouth during dental procedures, such as filling a... center. The device includes the rubber dam, rubber dam clamp, rubber dam frame, and forceps for a rubber... sexually transmitted diseases through oral sex; those devices are classified as condoms in § 884.5300 of...

21 CFR 872.6300 - Rubber dam and accessories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... center intended to isolate a tooth from fluids in the mouth during dental procedures, such as filling a... center. The device includes the rubber dam, rubber dam clamp, rubber dam frame, and forceps for a rubber... sexually transmitted diseases through oral sex; those devices are classified as condoms in § 884.5300 of...

21 CFR 872.6300 - Rubber dam and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... center intended to isolate a tooth from fluids in the mouth during dental procedures, such as filling a... center. The device includes the rubber dam, rubber dam clamp, rubber dam frame, and forceps for a rubber... sexually transmitted diseases through oral sex; those devices are classified as condoms in § 884.5300 of...

21 CFR 872.6300 - Rubber dam and accessories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... center intended to isolate a tooth from fluids in the mouth during dental procedures, such as filling a... center. The device includes the rubber dam, rubber dam clamp, rubber dam frame, and forceps for a rubber... sexually transmitted diseases through oral sex; those devices are classified as condoms in § 884.5300 of...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2011 CFR

2011-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2012 CFR

2012-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

40 CFR 63.498 - Back-end process provisions-recordkeeping.

Code of Federal Regulations, 2013 CFR

2013-07-01

... be the crumb rubber dry weight of the rubber leaving the stripper. (iv) The organic HAP content of... be the crumb rubber dry weight of the crumb rubber leaving the stripper. (iii) The hourly average of... test runs. (1) The uncontrolled residual organic HAP content in the latex or dry crumb rubber, as...

[Epidemiology of contact hypersensitivity to rubber components in manufacturers of automobile tires at the Stomil plant].

PubMed

Rubisz-Brzezińska, J; Bogdanowski, T; Brzezińska-Wcisło, L; Mozdzanowska, K; Bajcar, S

1990-01-01

Dermatological examination and patch tests with 34 rubber components were carried out in 114 tire manufacturers, 78 women and 36 men aged 29 years on average, with a mean duration of work in the plant 7 years. For correct interpretation of the obtained results patch tests with the same components were done in two control groups that is in 120 healthy subjects and 120 patients with contact dermatitis. Patch tests with proper concentrations of the studied components were evaluated after 48, 72 and 96 hours. Positive patch tests were found most frequently with antioxidants--16.6% (including IPPD--8.6%), followed by vulcanization accelerators--10.6%, and other rubber components--11.4% in all. During about 3 years of follow-up in 4 manufacturers contact allergic eczema was noted and polyvalent hypersensitivity to antioxidants and vulcanization accelerators without clinical manifestations of this hypersensitivity was diagnosed in 3 other subjects.

Synthesis of ethylene-propylene rubber graft copolymers by borane approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, T.C.; Janvikul, W.; Bernard, R.

1994-01-01

This paper describes a new method to prepare graft copolymers which have an EP rubber backbone and several free radical polymerized polymers grafted thereto. The process involves hydroboration of commercial EPDM rubbers, such as poly(ethylene-co-propylene-co-1,4-hexadiene) and poly(ethylene-co-propylene-co-5-ethylidene-2-norbornene), with 9-borabicyclononane (9-BBN). The resulting secondary alkyl-9-BBN moieties in the EPDM copolymer were then exposed to oxygen in the presence of free radical polymerizable monomers. Under certain conditions, the selective autoxidation reaction of secondary alkyl-9-BBN took place to create desirable polymeric radicals which can in situ initiate free radical polymerization. High graft efficiency was observed with controllable copolymer compositions. The graft copolymer ofmore » EP-g-PMMA is used to show the chemistry as well as some of the physical properties.« less

Genomic validation of PB 260 clone of rubber (Hevea brasiliensis) at Cikumpay Plantation by SSR marker

NASA Astrophysics Data System (ADS)

Royani, J. I.; Safarrida, A.; Rachmawati, I.; Khairiyah, H.; Mustika, I. P.; Suyono, A.; Rudiyana, Y.; Kubil; Nurjaya; Arianto, A.

2017-05-01

Rubber from Hevea brasiliensis is the only commercial natural rubber in the world. Propagation of rubber trees usually done by grafting and seed germination. BPPT had been producing rubber tree by in vitro technique with embryo somatic methods. Validation of mother plant for in vitro propagation is important to compare between mother plant and propagated plants. The aim for this research was to validation of PB 260 clone that planted at Cikumpay Plantation by SSR marker. Sampling of 10 rubber leaves were done at Cikumpay Plantation based on GPS position from the area of PB 260 clone. Rubber leaves were isolated with CTAB modification method to obtained DNA. Four of SSR primers from rubber, i.e.: hmac 4, hmac 5, hmct 1, and hmct 5, were used as primers to amplification of rubber DNA. The result showed that no band that different from 10 rubber of PB 260 clone at Cikumpay Plantation. This research will continue to compare genomic validation between mother plant and propagated plants that had been produced from BPPT.

Subcellular localization and interactions among rubber particle proteins from Hevea brasiliensis.

PubMed

Brown, Daniel; Feeney, Mistianne; Ahmadi, Mathin; Lonoce, Chiara; Sajari, Roslinda; Di Cola, Alessandra; Frigerio, Lorenzo

2017-11-02

Natural rubber (polyisoprene) from the rubber tree Hevea brasiliensis is synthesized by specialized cells called laticifers. It is not clear how rubber particles arise, although one hypothesis is that they derive from the endoplasmic reticulum (ER) membrane. Here we cloned the genes encoding four key proteins found in association with rubber particles and studied their intracellular localization by transient expression in Nicotiana benthamiana leaves. We show that, while the cis-prenyltransferase (CPT), responsible for the synthesis of long polyisoprene chains, is a soluble, cytosolic protein, other rubber particle proteins such as rubber elongation factor (REF), small rubber particle protein (SRPP) and Hevea rubber transferase 1-REF bridging protein (HRBP) are associated with the endoplasmic reticulum (ER). We also show that SRPP can recruit CPT to the ER and that interaction of CPT with HRBP leads to both proteins relocating to the plasma membrane. We discuss these results in the context of the biogenesis of rubber particles. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology.

A study of the influence of micro and nano phase morphology on the mechanical properties of a rubber-modified epoxy resin

NASA Astrophysics Data System (ADS)

Russell, Bobby Glenn

Epoxy resins are thermosets with extraordinary adhesion; high strength; good resistance to creep, heat, and chemicals; and they have low shrinkage. Conversely, these polymers are brittle, they are sensitive to moisture, and they exhibit poor toughness. To improve their toughness, they are often modified by introducing dispersed rubber particles in the primary phase. In this study, the epoxy resin was modified with carboxyl-terminated butadiene acrylonitrile (CTBN), liquid-reactive rubbers. The initiator concentration, percent acrylonitrile in the CTBN rubber, and cure temperatures were altered to give varying materials properties. Statistical analysis of the morphology data showed that the percentage of rubber acrylonitrile had an effect on both the rubber particle size and volume fraction. The cure temperature had an effect on the rubber particle volume and modulus. Plots of the rubber particle size, volume fraction, and modulus versus bulk elastic storage modulus and fracture toughness revealed that rubber particle size had no effect on bulk properties, volume fraction and rubber particle modulus had an effect on both the bulk storage elastic modulus and fracture toughness.

Preliminary Design and Evaluation of an Airfoil with Continuous Trailing-Edge Flap

NASA Technical Reports Server (NTRS)

Shen, Jinwei; Thornburgh, Robert P.; Kreshock, Andrew R.; Wilbur, Matthew L.; Liu, Yi

2012-01-01

This paper presents the preliminary design and evaluation of an airfoil with active continuous trailing-edge flap (CTEF) as a potential rotorcraft active control device. The development of structural cross-section models of a continuous trailing-edge flap airfoil is described. The CTEF deformations with MFC actuation are predicted by NASTRAN and UM/VABS analyses. Good agreement is shown between the predictions from the two analyses. Approximately two degrees of CTEF deflection, defined as the rotation angle of the trailing edge, is achieved with the baseline MFC-PZT bender. The 2D aerodynamic characteristics of the continuous trailing-edge flap are evaluated using a CFD analysis. The aerodynamic efficiency of a continuous trailing-edge flap is compared to that of a conventional discrete trailing-edge flap (DTEF). It is found that the aerodynamic characteristics of a CTEF are equivalent to those of a conventional DTEF with the same deflection angle but with a smaller flap chord. A fluid structure interaction procedure is implemented to predict the deflection of the continuous trailingedge flap under aerodynamic pressure. The reductions in CTEF deflection are overall small when aerodynamic pressure is applied: 2.7% reduction is shown with a CTEF deflection angle of two degrees and at angle of attack of six degrees. In addition, newly developed MFC-PMN actuator is found to be a good supplement to MFC-PZT when applied as the bender outside layers. A mixed MFC-PZT and MFC-PMN bender generates 3% more CTEF deformation than an MFC-PZT only bender and 5% more than an MFC-PMN only bender under aerodynamic loads.

BID is a critical factor controlling cell viability regulated by IFN-α.

PubMed

Tsuno, Takaya; Mejido, Josef; Zhao, Tongmao; Phillips, Terry; Myers, Timothy G; Bekisz, Joseph; Zoon, Kathryn C

2012-01-01

Clinical applications of human interferon (IFN)-α have met with varying degrees of success. Nevertheless, key molecules in cell viability regulated by IFN-α have not been clearly identified. Our previous study indicated that IFN (α, β, and ω) receptor (IFNAR) 1/2- and IFN regulatory factor 9-RNA interference (RNAi) completely restored cell viability after IFN-α treatment in human ovarian adenocarcinoma OVCAR3 cells sensitive to IFN-α. In this study, IFNAR1/2- and IFN regulatory factor 9-RNAi inhibited the gene expression of tumor necrosis factor-related apoptosis-inducing ligand (TRAIL), but not of Fas ligand, after IFN-α treatment. In fact, TRAIL but not Fas ligand inhibited the viability of OVCAR3 cells. IFN-α notably upregulated the levels of TRAIL protein in the supernatant and on the membrane of OVCAR3 cells. After TRAIL signaling, caspase 8 inhibitor and BH3 interacting domain death agonist (BID)-RNAi significantly restored cell viability in response to IFN-α and TRAIL in OVCAR3 cells. Furthermore, BID-RNAi prevented both IFN-α and TRAIL from collapsing the mitochondrial membrane potential (ΔΨm). Finally, we provided important evidence that BID overexpression led to significant inhibition of cell viability after IFN-α or TRAIL treatments in human lung carcinoma A549 cells resistant to IFN-α. Thus, this study suggests that BID is crucial for cell viability regulated by IFN-α which can induce mitochondria-mediated apoptosis, indicating a notable potential to be a targeted therapy for IFN-α resistant tumors.

Study on a Haptic Sensor Using MCF (Magnetic Compound Fluid) Electric Conductive Rubber

NASA Astrophysics Data System (ADS)

Zheng, Yaoyang; Shimada, Kunio

To provide a new composite material having a high degree of sensitivity regarding both electrical conduction and temperature for the field of robotics or sensing, we have developed magnetic rubber that contains a network-like magnetic cluster. We compared the temperature response of MCF rubber with others rubbers made under various experimental conditions, allowing us to find an optimum condition for making MCF rubber. The temperature response was obtained by an experimental equation. We also compared the electric conductivity of MCF rubber with that of ordinary electric conductive rubber and found that its electric sensitivity was lower at a small deformation, but increased at larger deformations. Therefore, MCF rubber has proven itself effective as a switching sensor when a small deformation is applied.

Continuous Trailing-Edge Flaps for Primary Flight Control of a Helicopter Main Rotor

NASA Technical Reports Server (NTRS)

Thornburgh, Robert P.; Kreshock, Andrew R.; Wilbur, Matthew L.; Sekula, Martin K.; Shen, Jinwei

2014-01-01

The use of continuous trailing-edge flaps (CTEFs) for primary flight control of a helicopter main rotor is studied. A practical, optimized bimorph design with Macro-Fiber Composite actuators is developed for CTEF control, and a coupled structures and computational fluid dynamics methodology is used to study the fundamental behavior of an airfoil with CTEFs. These results are used within a comprehensive rotorcraft analysis model to study the control authority requirements of the CTEFs when utilized for primary flight control of a utility class helicopter. A study of the effect of blade root pitch index (RPI) on CTEF control authority is conducted, and the impact of structural and aerodynamic model complexity on the comprehensive analysis results is presented. The results show that primary flight control using CTEFs is promising; however, a more viable option may include the control of blade RPI, as well.

Blowing-Type Boundary-Layer Control as Applied to the Trailing-Edge Flaps of a 35 Degree Swept-Wing Airplane

NASA Technical Reports Server (NTRS)

Kelly, Mark W; Anderson, Seth B; Innis, Robert C

1958-01-01

A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying blowing-type boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effects of boundary-layer control on the handling qualities and operation of the airplane, particularly during landing and take-off. The wind-tunnel and flight tests indicated that blowing over the flaps produced large increases in flap lift increment, and significant increases in maximum lift. The use of blowing permitted reductions in the landing approach speeds of as much as 12 knots.

Combination biological and microwave treatments of used rubber products

DOEpatents

Fliermans, Carl B.; Wicks, George G.

2002-01-01

A process and resulting product is provided in which a vulcanized solid particulate, such as vulcanized crumb rubber, has select chemical bonds altered by biotreatment with thermophillic microorganisms selected from natural isolates from hot sulfur springs. Following the biotreatment, microwave radiation is used to further treat the surface and to treat the bulk interior of the crumb rubber. The resulting combined treatments render the treated crumb rubber more suitable for use in new rubber formulations. As a result, larger loading levels and sizes of the treated crumb rubber can be used in new rubber mixtures and good properties obtained from the new recycled products.

Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

PubMed

Przepiórkowska, A; Chrońska, K; Zaborski, M

2007-03-06

The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

The Delicate Balance between Parental Protection, Unsupervised Wandering, and Adolescents' Autonomy and Its Relation with Antisocial Behavior: The TRAILS Study

ERIC Educational Resources Information Center

Sentse, Miranda; Dijkstra, Jan Kornelis; Lindenberg, Siegwart; Ormel, Johan; Veenstra, Rene

2010-01-01

In a large sample of early adolescents (T2: N = 1023; M age = 13.51; 55.5% girls), the impact of parental protection and unsupervised wandering on adolescents' antisocial behavior 2.5 years later was tested in this TRAILS study; gender and parental knowledge were controlled for. In addition, the level of biological maturation and having antisocial…

Invasive plant species how they can affect trail access (and how you can help prevent their access)

Treesearch

James H. Miller

2004-01-01

The natural beauty of our southern forest landscapes is under attack and our access to lands and trails are becoming increasingly restricted. Alien invasive plants are the culprits and they are spreading, occupying and controlling our lands like armies of invaders that they are. Kudzu is a world-wide recognized invader of the South, but few people sense the threat from...

Shear modulus and damping ratio of natural rubber containing carbon nanotubes

NASA Astrophysics Data System (ADS)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

This paper presents the results of an investigation into the potential application of Natural rubber (NR) containing Carbon Nanotubes (CNTs) by measuring its shear modulus and damping ratio. Four different types of rubber specimens which fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. It is observed that the shear modulus and damping ratio of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs.

A systems biology approach to overcome TRAIL resistance in cancer treatment.

PubMed

Selvarajoo, Kumar

2017-09-01

Over the last decade, our research team has investigated the dynamic responses and global properties of living cells using systems biology approaches. More specifically, we have developed computational models and statistical techniques to interpret instructive cell signaling and high-throughput transcriptome-wide behaviors of immune, cancer, and embryonic development cells. Here, I will focus on our recent works in overcoming cancer resistance. TRAIL (tumor necrosis factor related apoptosis-inducing ligand), a proinflammatory cytokine, has shown promising success in controlling cancer threat due to its ability to induce apoptosis in cancers specifically, while having limited effect on normal cells. Nevertheless, several malignant cancer types, such as fibrosarcoma (HT1080) or colorectal adenocarcinoma (HT29), remain non-sensitive to TRAIL. To sensitize HT1080 to TRAIL treatment, we first developed a dynamic computational model based on perturbation-response approach, to predict a crucial co-target to enhance cell death. The model simulations suggested that PKC inhibition together with TRAIL induce 95% cell death. Subsequently, we confirmed this result experimentally utilizing the PKC inhibitor, bisindolylmaleimide (BIM) I, and PKC siRNAs in HT1080. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of forests, roads and mistletoe on bird diversity in monoculture rubber plantations

PubMed Central

Sreekar, Rachakonda; Huang, Guohualing; Yasuda, Mika; Quan, Rui-Chang; Goodale, Eben; Corlett, Richard T.; Tomlinson, Kyle W.

2016-01-01

Rising global demand for natural rubber is expanding monoculture rubber (Hevea brasilensis) at the expense of natural forests in the Old World tropics. Conversion of forests into rubber plantations has a devastating impact on biodiversity and we have yet to identify management strategies that can mitigate this. We determined the life-history traits that best predict bird species occurrence in rubber plantations in SW China and investigated the effects of surrounding forest cover and distance to roads on bird diversity. Mistletoes provide nectar and fruit resources in rubber so we examined mistletoe densities and the relationship with forest cover and rubber tree diameter. In rubber plantations, we recorded less than half of all bird species extant in the surrounding area. Birds with wider habitat breadths and low conservation value had a higher probability of occurrence. Species richness and diversity increased logarithmically with surrounding forest cover, but roads had little effect. Mistletoe density increased exponentially with rubber tree diameters, but was unrelated to forest cover. To maximize bird diversity in rubber-dominated landscapes it is therefore necessary to preserve as much forest as possible, construct roads through plantations and not forest, and retain some large rubber trees with mistletoes during crop rotations. PMID:26903032

Time-Dependent Testing Evaluation and Modeling for Rubber Stopper Seal Performance.

PubMed

Zeng, Qingyu; Zhao, Xia

2018-01-01

Sufficient rubber stopper sealing performance throughout the entire sealed product life cycle is essential for maintaining container closure integrity in the parenteral packaging industry. However, prior publications have lacked systematic considerations for the time-dependent influence on sealing performance that results from the viscoelastic characteristics of the rubber stoppers. In this paper, we report results of an effort to study these effects by applying both compression stress relaxation testing and residual seal force testing for time-dependent experimental data collection. These experiments were followed by modeling fit calculations based on the Maxwell-Wiechert theory modified with the Kohlrausch-Williams-Watts stretched exponential function, resulting in a nonlinear, time-dependent sealing force model. By employing both testing evaluations and modeling calculations, an in-depth understanding of the time-dependent effects on rubber stopper sealing force was developed. Both testing and modeling data show good consistency, demonstrating that the sealing force decays exponentially over time and eventually levels off because of the viscoelastic nature of the rubber stoppers. The nonlinearity of stress relaxation derives from the viscoelastic characteristics of the rubber stoppers coupled with the large stopper compression deformation into restrained geometry conditions. The modeling fit with capability to handle actual testing data can be employed as a tool to calculate the compression stress relaxation and residual seal force throughout the entire sealed product life cycle. In addition to being time-dependent, stress relaxation is also experimentally shown to be temperature-dependent. The present work provides a new, integrated methodology framework and some fresh insights to the parenteral packaging industry for practically and proactively considering, designing, setting up, controlling, and managing stopper sealing performance throughout the entire sealed product life cycle. LAY ABSTRACT: Historical publications in the parenteral packaging industry have lacked systematic considerations for the time-dependent influence on the sealing performance that results from effects of viscoelastic characteristic of the rubber stoppers. This study applied compression stress relaxation testing and residual seal force testing for time-dependent experimental data collection. These experiments were followed by modeling fit calculations based on the Maxwell-Wiechert theory modified with the Kohlrausch-Williams-Watts stretched exponential function, resulting in a nonlinear, time-dependent sealing force model. Experimental and modeling data show good consistency, demonstrating that sealing force decays exponentially over time and eventually levels off. The nonlinearity of stress relaxation derives from the viscoelastic characteristics of the rubber stoppers coupled with the large stopper compression deformation into restrained geometry conditions. In addition to being time-dependent stress relaxation, it is also experimentally shown to be temperature-dependent. The present work provides a new, integrated methodology framework and some fresh insights to the industry for practically and proactively considering, designing, setting up, controlling, and managing of the stopper sealing performance throughout the entire sealed product life cycle. © PDA, Inc. 2018.

Natural rubber latex skin testing reagents: safety and diagnostic accuracy of nonammoniated latex, ammoniated latex, and latex rubber glove extracts.

PubMed

Hamilton, R G; Adkinson, N F

1996-11-01

Nonammoniated latex, ammoniated latex, and rubber glove extracts are the only sources of natural rubber (Hevea brasiliensis) latex that have potential for use as skin testing reagents in the diagnosis of latex allergy. Their diagnostic sensitivity and specificity as skin test reagents are unknown. We conducted a phase 1/2 clinical study to examine the safety and diagnostic accuracy (sensitivity and specificity) of nonammoniated latex, ammoniated latex, and rubber glove extracts as skin test extracts to identify the most efficacious source material for future skin test reagent development. Twenty-four adults not allergic to latex, 19 adults with hand dermatitis or pruritus, and 59 adults with a latex allergy were identified by clinical history. All provided blood and then received puncture skin tests and intradermal skin tests with nonammoniated latex, ammoniated latex, and rubber glove extracts from Malaysian H. brasiliensis latex by use of sequential titration. A glove provocation test and IgE anti-latex RAST were used to clarify positive history-negative skin test response and negative history-positive skin test response mismatches. All three extracts were biologically safe and sterile. After normalization to 1 mg/ml of total protein, all three extracts produced equivalent diagnostic sensitivity and specificity in puncture skin tests and intradermal skin tests at various extract concentrations. Optimal diagnostic accuracy was safely achieved at 100 micrograms/ml for intradermal skin tests (e.g., nonammoniated latex: puncture skin test sensitivity 96%, specificity 100%; intradermal skin test sensitivity 93%, specificity 96%). The presence of IgE antibody in skin was highly correlated with IgE anti-latex in serum (nonammoniated latex: r = 0.98, p < 0.001; ammoniated latex: r = 0.94, p < 0.001; rubber glove extract: r = 0.96, p < 0.001). All five available subjects with a positive history, negative skin test response, and absence of IgE antibody in serum had a negative glove provocation test response, indicating no clinical evidence of latex allergy. No systemic or large local allergic reactions were observed with puncture skin tests or intradermal skin tests. Equivalent diagnostic sensitivity and specificity were observed with the nonammoniated latex, ammoniated latex, and rubber glove extract skin test reagents after normalization for total protein; nonammoniated latex may be considered the reagent of choice on the basis of practical quality control and reproducibility considerations.

Electric field control in DC cable test termination by nano silicone rubber composite

NASA Astrophysics Data System (ADS)

Song, Shu-Wei; Li, Zhongyuan; Zhao, Hong; Zhang, Peihong; Han, Baozhong; Fu, Mingli; Hou, Shuai

2017-07-01

The electric field distributions in high voltage direct current cable termination are investigated with silicone rubber nanocomposite being the electric stress control insulator. The nanocomposite is composed of silicone rubber, nanoscale carbon black and graphitic carbon. The experimental results show that the physical parameters of the nanocomposite, such as thermal activation energy and nonlinearity-relevant coefficient, can be manipulated by varying the proportion of the nanoscale fillers. The numerical simulation shows that safe electric field distribution calls for certain parametric region of the thermal activation energy and nonlinearity-relevant coefficient. Outside the safe parametric region, local maximum of electric field strength around the stress cone appears in the termination insulator, enhancing the breakdown of the cable termination. In the presence of the temperature gradient, thermal activation energy and nonlinearity-relevant coefficient work as complementary factors to produce a reasonable electric field distribution. The field maximum in the termination insulator show complicate variation in the transient processes. The stationary field distribution favors the increase of the nonlinearity-relevant coefficient; for the transient field distribution in the process of negative lighting impulse, however, an optimized value of the nonlinearity-relevant coefficient is necessary to equalize the electric field in the termination.

The Effect of Particles on Electrolytically Polymerized Thin Natural MCF Rubber for Soft Sensors Installed in Artificial Skin.

PubMed

Shimada, Kunio; Mochizuki, Osamu; Kubota, Yoshihiro

2017-04-19

The aim of this study is to investigate the effect of particles as filler in soft rubber sensors installed in artificial skin. We examine sensors made of natural rubber (NR-latex) that include magnetic particles of Ni and Fe₃O₄ using magnetic compound fluid (MCF). The 1-mm thickness of the electrolytically polymerized MCF rubber makes production of comparatively thin rubber sensors feasible. We first investigate the effect of magnetic particles Ni and Fe₃O₄ on the curing of MCF rubber. Next, in order to adjust the electric properties of the MCF rubber, we adopt Al₂O₃ dielectric particles. We investigate the effect of Al₂O₃ particles on changes in electric current, voltage and temperature of electrolytically polymerized MCF rubber liquid, and on the electric properties under the application of normal and shear forces. By adjusting the ratio of Ni, Fe₃O₄, Al₂O₃ and water in MCF rubber with Al₂O₃, it is possible to change the electric properties.

Research on Extrusion of Rubber Composites Reinforced by Short Fibers Orientation Based on FEA

NASA Astrophysics Data System (ADS)

Zhang, Dewei; Wang, Chuansheng; Shen, Bo; Li, Shaoming; Bian, Huiguang

2018-06-01

In recent years, rubber composites reinforced by short fibers has been researched deeply, because of its good performances such as higher wear resistance, higher cut resistance and so on. Some research results indicated that if short fibers get orientation in rubber composites, the performances of rubber products could be promoted greatly. But how to make short fibers get orientation in rubber matrix during extrusion is still a real problem. And there are many parameters affect the short fibers orientation. So, in this paper, the effects of die structure including expansion-die and dam-expansion-die on extrusion flow field of short fiber and rubber composite material during extrusion process has been researched by Polyflow. And the FEA results about the pressure field, velocity field and the velocity vector of the rubber composites flow field indicate that, comparing with expansion-die and the dam-expansion-die, the latter one is better for the extrusion process of rubber composites and making short fibers get radial orientation in rubber matrix.

Tough Rubber.

ERIC Educational Resources Information Center

Schmid, Sue

1994-01-01

Describes the benefits of using rubber floor coverings in a gym's free-weight and cardiovascular equipment areas. Tips on purchasing a rubber floor are highlighted as is an annotated list of suppliers and their rubber flooring products. (GR)

Natural rubber (NR) biosynthesis: perspectives from polymer chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barkakaty, Balaka

Natural rubber is an important strategic raw material for manufacturing a wide variety of industrial products. There are at least 2,500 different latex-producing plant species; however, only Hevea brasiliensis (the Brazilian rubber tree) is a commercial source. The chemical structure of natural rubber is cis-1,4-polyisoprene, but the exact structure of the head and end groups remains unknown. Since synthetic cis-1,4-polyisoprenes cannot match the superior properties of natural rubber, understanding the chemistry behind the biosynthetic process is key to finding a possible replacement. T his chapter summarizes our current understandings from the perspective of a polymer scientist by comparing synthetic polyisoprenesmore » to natural rubber. The chapter also highlights biomimetic polymerization, research towards a synthetic match of natural rubber and the role of natural rubber in health care.« less

Higher modulus compositions incorporating particulate rubber

DOEpatents

Bauman, B.D.; Williams, M.A.; Bagheri, R.

1997-12-02

Rubber particles, to be used as fillers or extenders for various composite polymer systems, are chlorinated by a gas-solid phase reaction with a chlorine-containing gas. A composite polymer containing the chlorinated rubber fillers or extenders exhibits a higher flexural modulus than if prepared using an unchlorinated rubber filler or extender. Chlorination of the rubber particles is carried out by contacting the finely divided rubber particles with a chlorine-containing gas comprising at least about 5 volume percent chlorine. Advantageously, the chlorine can be diluted with air, nitrogen or other essentially inert gases and may contain minor amounts of fluorine. Improved performance is obtained with nitrogen dilution of the chlorine gas over air dilution. Improved polymer composite systems having higher flexural modulus result from the use of the chlorinated rubber particles as fillers instead of unchlorinated rubber particles. 2 figs.

Higher modulus compositions incorporating particulate rubber

DOEpatents

McInnis, E.L.; Scharff, R.P.; Bauman, B.D.; Williams, M.A.

1995-01-17

Rubber particles, to be used as fillers or extenders for various composite polymer systems, are chlorinated by a gas-solid phase reaction with a chlorine-containing gas. A composite polymer containing the chlorinated rubber fillers or extenders exhibits a higher flexural modulus than if prepared using an unchlorinated rubber filler or extender. Chlorination of the rubber particles is carried out by contacting the finely divided rubber particles with a chlorine-containing gas comprising at least about 5 volume percent chlorine. Advantageously, the chlorine can be diluted with air, nitrogen or other essentially inert gases and may contain minor amounts of fluorine. Improved performance is obtained with nitrogen dilution of the chlorine gas over air dilution. Improved polymer composite systems having higher flexural modulus result from the use of the chlorinated rubber particles as fillers instead of unchlorinated rubber particles. 2 figures.

Higher modulus compositions incorporating particulate rubber

DOEpatents

McInnis, E.L.; Bauman, B.D.; Williams, M.A.

1996-04-09

Rubber particles, to be used as fillers or extenders for various composite polymer systems, are chlorinated by a gas-solid phase reaction with a chlorine-containing gas. A composite polymer containing the chlorinated rubber fillers or extenders exhibits a higher flexural modulus than if prepared using an unchlorinated rubber filler or extender. Chlorination of the rubber particles is carried out by contacting the finely divided rubber particles with a chlorine-containing gas comprising at least about 5 volume percent chlorine. Advantageously, the chlorine can be diluted with air, nitrogen or other essentially inert gases and may contain minor amounts of fluorine. Improved performance is obtained with nitrogen dilution of the chlorine gas over air dilution. Improved polymer composite systems having higher flexural modulus result from the use of the chlorinated rubber particles as fillers instead of unchlorinated rubber particles. 2 figs.

On the stability and control of a trailing vortex

NASA Astrophysics Data System (ADS)

Edstrand, Adam M.

Trailing vortices are both a fundamental and practical problem of fluid mechanics. Fundamentally, they provide a canonical vortex flow that is pervasive in finite aspect ratio lifting bodies, practically producing many adverse effects across aeronautical and maritime applications. These adverse effects coupled with the broad range of applicability make their active control desirable; however, they remain robust to control efforts. Experimental baseline results provided an explanation of vortex wandering, the side-to-side motion often attributed to wind-tunnel unsteadiness or a vortex instability. We extracted the wandering motion and found striking similarities with the eigenmodes, growth rates, and frequencies from a stability analysis of the Batchelor vortex. After concluding that wandering is a result of a vortex instability, we applied control to the trailing vortex flow field through blowing from a slot at the wingtip. We experimentally obtained modest reductions in the metrics, but found the parameter space for optimization unwieldy. With the ultimate goal of designing control, we performed a physics-based stability analysis in the wake of a NACA0012 wing with an aspect ratio of 1.25 positioned at a geometric angle of attack of 5 degrees. Numerically computing the base flow at a chord Reynolds number of 1000, we perform a parallel temporal and spatial stability analysis three chords downstream of the trailing edge finding seven instabilities: three temporal, four spatial. The three temporal contain a wake instability, a vortex instability, and a mixed instability, which is a higher-order wake instability. The primary instability localized to the wake results from the two-dimensional wake, while the secondary instability is the mixed instability, containing higher-order spanwise structures in the wake. These instabilities imply that although it may be intuitive to place control at the wingtip, these results show that control may be more effective at the trailing edge, which would excite these instabilities that result with the eventual break up of the vortex. Further, by performing a wave-packet analysis, we found the wave packets contained directivity, coming inward toward the vortex above and below the wing, and traveling outward in the spanwise directions. We conjecture that this directivity can be translated to receptivity, with free-stream disturbances above and below the wing being more receptive than spanwise disturbances. With this, we provide two methods for instability excitation: utilizing control devices on the wing to excite near-field instabilities directly and utilizing free-stream disturbances to such as a speaker to excite near-field instabilities through receptivity.

Numerical study on influence of single control surface on aero elastic behavior of forward-swept wing

NASA Astrophysics Data System (ADS)

Wang, Ning; Su, Xinbing; Ma, Binlin; Zhang, Xiaofei

2017-10-01

In order to study the influence of elastic forward-swept wing (FSW) with single control surface, the computational fluid dynamics/computational structural dynamics (CFD/CSD) loose coupling static aero elastic numerical calculation method was adopted for numerical simulation. The effects of the elastic FSW with leading- or trailing-edge control surface on aero elastic characteristics were calculated and analysed under the condition of high subsonic speed. The result shows that, the deflection of every single control surface could change the aero elastic characteristics of elastic FSW greatly. Compared with the baseline model, when leading-edge control surface deflected up, under the condition of small angles of attack, the aerodynamic characteristics was poor, but the bending and torsional deformation decreased. Under the condition of moderate angles of attack, the aerodynamic characteristics was improved, but bending and torsional deformation increased; When leading-edge control surface deflected down, the aerodynamic characteristics was improved, the bending and torsional deformation decreased/increased under the condition of small/moderate angles of attack. Compared with the baseline model, when trailing-edge control surface deflected down, the aerodynamic characteristics was improved. The bending and torsional deformation increased under the condition of small angles of attack. The bending deformation increased under the condition of small angles of attack, but torsional deformation decreases under the condition of moderate angles of attack. So, for the elastic FSW, the deflection of trailing-edge control surface play a more important role on the improvement of aerodynamic and elastic deformation characteristics.

Biodiesel production methods of rubber seed oil: a review

NASA Astrophysics Data System (ADS)

Ulfah, M.; Mulyazmi; Burmawi; Praputri, E.; Sundari, E.; Firdaus

2018-03-01

The utilization of rubber seed as raw material of biodiesel production is seen highly potential in Indonesia. The availability of rubber seeds in Indonesia is estimated about 5 million tons per annum, which can yield rubber seed oil about 2 million tons per year. Due to the demand of edible oils as a food source is tremendous and the edible oil feedstock costs are far expensive to be used as fuel, production of biodiesel from non-edible oils such as rubber seed is an effective way to overcome all the associated problems with edible oils. Various methods for producing biodiesel from rubber seed oil have been reported. This paper introduces an optimum condition of biodiesel production methods from rubber seed oil. This article was written to be a reference in the selection of methods and the further development of biodiesel production from rubber seed oil. Biodiesel production methods for rubber seed oils has been developed by means of homogeneous catalysts, heterogeneous catalysts, supercritical method, ultrasound, in-situ and enzymatic processes. Production of biodiesel from rubber seed oil using clinker loaded sodium methoxide as catalyst is very interesting to be studied and developed further.

Crumb Rubber Recycling in Enhancing Damping Properties of Concrete

NASA Astrophysics Data System (ADS)

Sugapriya, P.; Ramkrishnan, R.

2018-02-01

Damping plays a major role in the design of roadside structures that gets affected due to vibrations transmitted from moving traffic. In this study, fine aggregates were partially replaced with crumb rubber in concrete, at varying percentages of 5, 10, 15 and 20% by weight. Three different sets of concrete, mixed with crumb rubber were prepared using raw rubber, treated rubber and treated rubber with partial replacement of cement. Cement was partially replaced with Ultra-Fine Ground Granulated Blast furnace Slag (UFGGBS) for this study. Samples were cast, cured and tested for various properties on the 7th and 28th day. The damping ratio and frequency of the peak value from a number of waves in rubber incorporated beams were found out using a FFT Analyser along with its Strength, Damping and Sorptivity characteristics. SEM analysis was conducted to analyse the micro structural bonding between rubber and concrete. The mode shapes of pavement slabs were modelled and analysed using a FEM tool, ANSYS. From the results, the behaviour of the three sets of rubberized concrete were compared and analysed, and an optimum percentage for crumb rubber and UFGGBS was proposed to achieve best possible damping without compromising the strength properties.

Parametric Evaluation of Thin, Transonic Circulation-Control Airfoils

NASA Technical Reports Server (NTRS)

Schlecht, Robin; Anders, Scott

2007-01-01

Wind-tunnel tests were conducted in the NASA Langley Transonic Dynamics Tunnel on a 6 percent-thick, elliptical circulation-control airfoil with upper-surface and lower-surface blowing capability. Results for elliptical Coanda trailing-edge geometries, biconvex Coanda trailing-edge geometries, and leading-edge geometries are reported. Results are presented at subsonic and transonic Mach numbers of 0.3 and 0.8, respectively. When considering one fixed trailing-edge geometry, for both the subsonic and transonic conditions it was found that the [3.0:1] ratio elliptical Coanda surface with the most rounded leading-edge [03] performed favorably and was determined to be the best compromise between comparable configurations that took advantage of the Coanda effect. This configuration generated a maximum. (Delta)C(sub 1) = 0.625 at a C(sub mu) = 0.06 at M = 0.3, alpha = 6deg. This same configuration generated a maximum (Delta)C(sub 1) = 0.275 at a C(sub mu) = 0.0085 at M = 0.8, alpha = 3deg.

Alveolar epithelial cells in idiopathic pulmonary fibrosis display upregulation of TRAIL, DR4 and DR5 expression with simultaneous preferential over-expression of pro-apoptotic marker p53.

PubMed

Akram, Khondoker M; Lomas, Nicola J; Forsyth, Nicholas R; Spiteri, Monica A

2014-01-01

Idiopathic pulmonary fibrosis (IPF) is a progressive, debilitating, and fatal lung disease of unknown aetiology with no current cure. The pathogenesis of IPF remains unclear but repeated alveolar epithelial cell (AEC) injuries and subsequent apoptosis are believed to be among the initiating/ongoing triggers. However, the precise mechanism of apoptotic induction is hitherto elusive. In this study, we investigated expression of a panel of pro-apoptotic and cell cycle regulatory proteins in 21 IPF and 19 control lung tissue samples. We reveal significant upregulation of the apoptosis-inducing ligand TRAIL and its cognate receptors DR4 and DR5 in AEC within active lesions of IPF lungs. This upregulation was accompanied by pro-apoptotic protein p53 overexpression. In contrast, myofibroblasts within the fibroblastic foci of IPF lungs exhibited high TRAIL, DR4 and DR5 expression but negligible p53 expression. Similarly, p53 expression was absent or negligible in IPF and control alveolar macrophages and lymphocytes. No significant differences in TRAIL expression were noted in these cell types between IPF and control lungs. However, DR4 and DR5 upregulation was detected in IPF alveolar macrophages and lymphocytes. The marker of cellular senescence p21(WAF1) was upregulated within affected AEC in IPF lungs. Cell cycle regulatory proteins Cyclin D1 and SOCS3 were significantly enhanced in AEC within the remodelled fibrotic areas of IPF lungs but expression was negligible in myofibroblasts. Taken together these findings suggest that, within the remodelled fibrotic areas of IPF, AEC can display markers associated with proliferation, senescence, and apoptotosis, where TRAIL could drive the apoptotic response. Clear understanding of disease processes and identification of therapeutic targets will direct us to develop effective therapies for IPF.

Ubiquitin-specific protease 8 links the PTEN-Akt-AIP4 pathway to the control of FLIPS stability and TRAIL sensitivity in glioblastoma multiforme.

PubMed

Panner, Amith; Crane, Courtney A; Weng, Changjiang; Feletti, Alberto; Fang, Shanna; Parsa, Andrew T; Pieper, Russell O

2010-06-15

The antiapoptotic protein FLIP(S) is a key suppressor of tumor necrosis factor-related apoptosis-inducing ligand (TRAIL)-induced apoptosis in human glioblastoma multiforme (GBM) cells. We previously reported that a novel phosphatase and tensin homologue (PTEN)-Akt-atrophin-interacting protein 4 (AIP4) pathway regulates FLIP(S) ubiquitination and stability, although the means by which PTEN and Akt were linked to AIP4 activity were unclear. Here, we report that a second regulator of ubiquitin metabolism, the ubiquitin-specific protease 8 (USP8), is a downstream target of Akt, and that USP8 links Akt to AIP4 and the regulation of FLIP(S) stability and TRAIL resistance. In human GBM xenografts, levels of USP8 correlated inversely with pAkt levels, and genetic or pharmacologic manipulation of Akt regulated USP8 levels in an inverse manner. Overexpression of wild-type USP8, but not catalytically inactive USP8, increased FLIP(S) ubiquitination, decreased FLIP(S) half-life, decreased FLIP(S) steady-state levels, and decreased TRAIL resistance, whereas short interfering RNA (siRNA)-mediated suppression of USP8 levels had the opposite effect. Because high levels of the USP8 deubiquitinase correlated with high levels of FLIP(S) ubiquitination, USP8 seemed to control FLIP(S) ubiquitination through an intermediate target. Consistent with this idea, overexpression of wild-type USP8 decreased the ubiquitination of the FLIP(S) E3 ubiquitin ligase AIP4, an event previously shown to increase AIP4-FLIP(S) interaction, whereas siRNA-mediated suppression of USP8 increased AIP4 ubiquitination. Furthermore, the suppression of FLIP(S) levels by USP8 overexpression was reversed by the introduction of siRNA targeting AIP4. These results show that USP8, a downstream target of Akt, regulates the ability of AIP4 to control FLIP(S) stability and TRAIL sensitivity.

High-order TRAIL oligomer formation in TRAIL-coated lipid nanoparticles enhances DR5 cross-linking and increases antitumour effect against colon cancer.

PubMed

De Miguel, Diego; Gallego-Lleyda, Ana; Ayuso, José María; Pejenaute-Ochoa, Dolores; Jarauta, Vidal; Marzo, Isabel; Fernández, Luis J; Ochoa, Ignacio; Conde, Blanca; Anel, Alberto; Martinez-Lostao, Luis

2016-12-28

During the last years, a great effort has been invested into developing new TRAIL formulations with increased bioactivity, trying to overcome the resistance to conventional soluble TRAIL (sTRAIL) exhibited by many primary tumours. In our group, we have generated artificial lipid nanoparticles decorated with sTRAIL (LUV-TRAIL), emulating the physiological TRAIL-containing exosomes by which T-cells release TRAIL upon activation. We already demonstrated that LUV-TRAIL has greater cytotoxicity against both chemoresistant haematologic tumour cells and epithelial carcinoma cells compared to a form of sTRAIL similar to that used in clinical trials. In this study we have tested LUV-TRAIL in several human colon cancer cell lines with different sensitivity to sTRAIL. LUV-TRAIL significantly improved sTRAIL cytotoxicity in all colon cancer cell lines tested. Trying to ascertain the molecular mechanism by which LUV-TRAIL exhibited improved cytotoxicity, we demonstrated that TRAIL-coated lipid nanoparticles were able to activate DR5 more efficiently than sTRAIL, and this relied on LUV-TRAIL ability to promote DR5 clustering on the cell surface. Moreover, we show that TRAIL molecules are arranged in higher order oligomers only in LUV-TRAIL, which may explain their enhanced DR5 clustering ability. Finally, LUV-TRAIL showed significantly better antitumour activity than sTRAIL in an in vivo model using HCT-116 xenograft tumours in nude mice, validating its potential clinical application. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

[Study of an adherence rating score system for tuberculosis patients in China].

PubMed

Yuan, Yan-li; Yu, Bao-zhu; Jiang, Shi-wen; Wang, Tao; Lv, Jun; Tao, Qiu-Shan

2010-06-18

To develop an adherence rating score (ARS) system specific for tuberculosis (TB) patients. A cross-sectional survey of 124 TB patients was conducted to figure out risk factors for adherence to treatment. The step-wise logistic regression models were used for selecting adherence-related variables. ARS was developed based on the weighting scores of the parameters of all the predicted variables in the logistic model. The reliability and responsibility of ARS was evaluated by using external data from an open label randomized controlled trial on 574 TB patients. The patients were grouped as adherence group (247 patients) and non-adherence group (327 patients) based on the predicted ARS. And the non-adherence group was randomized divided into a trail group (146 patients) and a control group (181 patients). The intervention for the trail group was custom health educational material aimed to reduce ARS, while the intervention for control groups was general TB education material, which was routinely used in the current local TB control settings. The cumulative non-adherence rates of the three groups were compared with each other after six-month follow-up period of treatment. The ARS system had 7 items which covered the following domains: disease status, psychology, patients' KAP (knowledge, attitude, and practice), regularly life-style and social supports. The score of ARS was 2.38+/-0.18 (mean+/-SD) for adherence patients, and 4.69 +/-0.20 (mean+/-SD) for non-adherence patients (t=8.52, P<0.01). In the randomized controlled trial, the six months cumulative non-adherence rates ware 24.7% for the trail group and it was 41.4% for the control group(P<0.01); while the six months cumulative non-adherence rates were not statistical significant difference between trail group and adherence group (P>0.05). The ARS system was reliability and validity for evaluating the adherence of TB treatment in the stop TB settings in China.

A review on the suitability of rubberized concrete for concrete bridge decks

NASA Astrophysics Data System (ADS)

Syamir Senin, Mohamad; Shahidan, Shahiron; Radziah Abdullah, Siti; Anting Guntor, Nickholas; Syazani Leman, Alif

2017-11-01

Road authorities manage a large population of ageing bridges, a substantial number of which fail to meet the current requirements either due to deterioration and other structural deficiencies or as a result of the escalating demands imposed by increased traffic. This problem is related to the dynamic load from vehicles. This problem can be solved by producing a type of concrete that can reduce the amplitude of oscillation or vibration such as rubberized concrete. Green construction has been a very important aspect in concrete production field in the last decade. One of the most problematic waste materials is scrap tires. The use of scrap tires in civil engineering is increasing by producing rubberized concrete. Rubberized concrete is a type of concrete that is mixed with rubber. The purpose of this review is to justify the suitability of rubberized concrete for concrete bridge decks. Several parameters named physical, chemical and mechanical properties were measured to ensure the suitability of rubberized concrete for concrete bridge decks. Rubberized concrete has similar workability to normal concrete. The rubber reduced the density and compressive strength of the concrete while increased the flexural strength, water absorption and damping ratio. The used of rubber in concrete beyond 20% is not recommended due to decreasing in compressive strength. Rubberized concrete recommended to be used in circumstances where vibration damping was required such as in bridge construction as shock-wave absorber.

Performance of USDA guayule lines in the Northern Negev of Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mills, D.; Benzioni, A.; Forti, M.

The rubber yield of the guayule plant (Parthenium argentatum) is determined by its rubber concentration and biomass production, both of which are a function of genetic constituents and environmental conditions. With the aim of selecting best performing lines of guayule under the climatic conditions of the northern Negev of Israel, two-yr-old guayule plants from 13 USDA lines were evaluated for height, spread, canopy fresh and dry weight, branch and leaf dry weight, rubber and resin concentration, and rubber and resin yield per plant. Significant differences were found among the lines for all the characteristics tested. Lines 11600 and 11604 excelledmore » in rubber and biomass production and were taller and more uniform than the other lines; whereas line N593, conventionally used as a standard, performed poorly and was less uniform. The correlation between rubber yield per plant and rubber concentration was poor, rubber yield being related mainly to biomass production and to a lesser degree to height and spread of the plants. Taken together with fact that biomass production was more variable than rubber concentration, this finding suggests that breeding and selection of guayule and for high rubber yield should be directed primarily towards improvement of biomass production rather than rubber concentration. In the northern Negev of Israel, USDA lines 11600 and 11604 performed well.« less

40 CFR Table 5 to Subpart U of... - Known Organic HAP Emitted From the Production of Elastomer Products

Code of Federal Regulations, 2010 CFR

2010-07-01

...) ✔ Epichlorohydrin (106898) ✔ Ethylbenzene (100414) ✔ ✔ Ethylene Dichloride (107062) ✔ Ethylene Oxide (75218... Rubber. EPI = Epichlorohydrin Rubber. EPR = Ethylene Propylene Rubber. HBR = Halobutyl Rubber. HYP...

Rubber friction on road surfaces: Experiment and theory for low sliding speeds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lorenz, B.; Persson, B. N. J.; Oh, Y. R.

We study rubber friction for tire tread compounds on asphalt road surfaces. The road surface topographies are measured using a stylus instrument and atomic force microscopy, and the surface roughness power spectra are calculated. The rubber viscoelastic modulus mastercurves are obtained from dynamic mechanical analysis measurements and the large-strain effective modulus is obtained from strain sweep data. The rubber friction is measured at different temperatures and sliding velocities, and is compared to the calculated data obtained using the Persson contact mechanics theory. We conclude that in addition to the viscoelastic deformations of the rubber surface by the road asperities, theremore » is an important contribution to the rubber friction from shear processes in the area of contact. The analysis shows that the latter contribution may arise from rubber molecules (or patches of rubber) undergoing bonding-stretching-debonding cycles as discussed in a classic paper by Schallamach.« less

Structural characterization of rubber from jackfruit and euphorbia as a model of natural rubber.

PubMed

Mekkriengkrai, Dararat; Ute, Koiichi; Swiezewska, Ewa; Chojnacki, Tadeusz; Tanaka, Yasuyuki; Sakdapipanich, Jitladda T

2004-01-01

A structural study of low molecular weight rubbers from Jackfruit (Artocarpus heterophyllus) and Painted spurge (Euphorbia heterophylla) was carried out as model compounds of natural rubber from Hevea brasiliensis. The rubber content of latex from Jackfruit was 0.4-0.7%, which is very low compared with that of 30-35% in the latex from Hevea tree. The rubber from Jackfruit latex was low molecular weight with narrow unimodal molecular weight distribution (MWD), whereas that obtained from E. heterophylla showed very broad MWD. The 1H and 13C NMR analyses showed that Jackfruit rubber consists of a dimethylallyl group and two trans-isoprene units connected to a long sequence of cis-isoprene units. The alpha-terminal group of Jackfruit rubber was presumed to be composed of a phosphate group based on the presence of 1H NMR signal at 4.08 ppm corresponding to the terminal =CH-CH2OP group.

Flight control system development and flight test experience with the F-111 mission adaptive wing aircraft

NASA Technical Reports Server (NTRS)

Larson, R. R.

1986-01-01

The wing on the NASA F-111 transonic aircraft technology airplane was modified to provide flexible leading and trailing edge flaps. This wing is known as the mission adaptive wing (MAW) because aerodynamic efficiency can be maintained at all speeds. Unlike a conventional wing, the MAW has no spoilers, external flap hinges, or fairings to break the smooth contour. The leading edge flaps and three-segment trailing edge flaps are controlled by a redundant fly-by-wire control system that features a dual digital primary system architecture providing roll and symmetric commands to the MAW control surfaces. A segregated analog backup system is provided in the event of a primary system failure. This paper discusses the design, development, testing, qualification, and flight test experience of the MAW primary and backup flight control systems.

23 CFR 751.7 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... not nonconforming junkyards. (b) Junk. Old or scrap metal, rope, rags, batteries, paper, trash, rubber... relative to Outdoor Advertising Control shall apply insofar as industrial zones are concerned. (e) Unzoned...

Pyrogen tests of infusions, blood anticoagulant solutions, plastic materials and rubber products.

PubMed

Pintér, J; Zsdánszky, C; Györffy, G

1977-01-01

The methods of the pyrogen test in rabbit as adopted by the authors are presented. The test includes positive and negative controls. The conditions of using the same rabbits on two consecutive days are discussed. Methods of sampling of sterile infusions and the preparation for pyrogen test of anticoagulant solutions containing citrate, phosphate and/or edetate ions are presented. The necessity of pyrogen control of distilled water is stressed. Attention is called on the importance of testing for pyrogenicity of the plastic materials and the rubber-wares to be applied during the production of anticoagulant solutions and infusions. A pyrogen test highly sensitive for detecting traces of detergent is applied for washed glassware. It is emphasized that sensitive pyrogen tests are indispensable not only when new derivatives are being introduced, but also during routine control, because occasional changes in the manufacturer's technology may sometimes be demonstrable in this way.

Kinetics of zinc release from ground tire rubber and rubber ash in a calcareous soil as alternatives to Zn fertilizers

USDA-ARS?s Scientific Manuscript database

Ground rubber contains 15-20 g Zn/kg but very low levels of Cd and could serve as an inexpensive byproduct Zn fertilizer. The aim of this investigation was to test the kinetics of Zn release in a soil treated with ground tire rubber and rubber ash compared with commercial Zn fertilizer and a labora...

Source Hierarchy List. Volume 2. E through N

DTIC Science & Technology

1994-07-01

SEE CONTINENTAL AG HANNOVER (GERMANY F R) 421628 02 GENERAL TIRE AND RUBBER CO MARION IN 151750 02 GENERAL TIRE ANO RUBBER CO WABASH IN...151800 03 GENERAL TIRE AND RUBBER CO WABASH IN 151820 INDUSTRIAL PRODUCTS DIV...GENERAL TIRE AND RUBBER CO WABASH IN 151800 FOR HIGHEST ORGANIZATIONAL LEVEL SEE CONTINENTAL AG HANNOVER (GERMANY F R) G3 GENERAL TIRE AND RUBBER CO

Strategies to improve the adhesion of rubbers to adhesives by means of plasma surface modification

NASA Astrophysics Data System (ADS)

Martín-Martínez, J. M.; Romero-Sánchez, M. D.

2006-05-01

The surface modifications produced by treatment of a synthetic sulfur vulcanized styrene-butadiene rubber with oxidizing (oxygen, air, carbon dioxide) and non oxidizing (nitrogen, argon) RF low pressure plasmas, and by treatment with atmospheric plasma torch have been assessed by ATR-IR and XPS spectroscopy, SEM, and contact angle measurements. The effectiveness of the low pressure plasma treatment depended on the gas atmosphere used to generate the plasma. A lack of relationship between surface polarity and wettability, and peel strength values was obtained, likely due to the cohesive failure in the rubber obtained in the adhesive joints. In general, acceptable adhesion values of plasma treated rubber were obtained for all plasmas, except for nitrogen plasma treatment during 15 minutes due to the creation of low molecular weight moieties on the outermost rubber layer. A toluene wiping of the N{2 } plasma treated rubber surface for 15 min removed those moieties and increased adhesion was obtained. On the other hand, the treatment of the rubber with atmospheric pressure by means of a plasma torch was proposed. The wettability of the rubber was improved by decreasing the rubber-plasma torch distance and by increasing the duration because a partial removal of paraffin wax from the rubber surface was produced. The rubber surface was oxidized by the plasma torch treatment, and the longer the duration of the plasma torch treatment, the higher the degree of surface oxidation (mainly creation of C O moieties). However, although the rubber surface was effectively modified by the plasma torch treatment, the adhesion was not greatly improved, due to the migration of paraffin wax to the treated rubber-polyurethane adhesive interface once the adhesive joint was produced. On the other hand, the extended treatment with plasma torch facilitated the migration of zinc stearate to the rubber-adhesive interface, also contributing to deteriorate the adhesion in greater extent. Finally, it has been found that cleaning of SBS rubber in an ultrasonic bath prior to plasma torch treatment produced a partial removal of paraffin waxes from the surface, and thus improved adhesion was obtained.

Detection of Interfacial Debonding in a Rubber-Steel-Layered Structure Using Active Sensing Enabled by Embedded Piezoceramic Transducers.

PubMed

Feng, Qian; Kong, Qingzhao; Jiang, Jian; Liang, Yabin; Song, Gangbing

2017-09-01

Rubber-steel-layered structures are used in many engineering applications. Laminated rubber-steel bearing, as a type of seismic isolation device, is one of the most important applications of the rubber-steel-layered structures. Interfacial debonding in rubber-steel-layered structures is a typical failure mode, which can severely reduce their load-bearing capacity. In this paper, the authors developed a simple but effective active sensing approach using embedded piezoceramic transducers to provide an in-situ detection of the interfacial debonding between the rubber layers and steel plates. A sandwiched rubber-steel-layered specimen, consisting of one rubber layer and two steel plates, was fabricated as the test specimen. A novel installation technique, which allows the piezoceramic transducers to be fully embedded into the steel plates without changing the geometry and the surface conditions of the plates, was also developed in this research. The active sensing approach, in which designed stress waves can propagate between a pair of the embedded piezoceramic transducers (one as an actuator and the other one as a sensor), was employed to detect the steel-rubber debonding. When the rubber-steel debonding occurs, the debonded interfaces will attenuate the propagating stress wave, so that the amplitude of the received signal will decrease. The rubber-steel debonding was generated by pulling the two steel plates in opposite directions in a material-testing machine. The changes of the received signal before and after the debonding were characterized in a time domain and further quantified by using a wavelet packet-based energy index. Experiments on the healthy rubber-steel-layered specimen reveal that the piezoceramic-induced stress wave can propagate through the rubber layer. The destructive test on the specimen demonstrates that the piezoceramic-based active sensing approach can effectively detect the rubber-steel debonding failure in real time. The active sensing approach is often used in structures with "hard" materials, such as steel, concrete, and carbon fiber composites. This research lays a foundation for extending the active sensing approach to damage detection of structures involving "soft" materials, such as rubber.

Research on the conductivity of a haptic sensor, especially with the sensor under extended condition

NASA Astrophysics Data System (ADS)

Zheng, Yaoyang; Shimada, Kunio

2008-11-01

The present paper describes the application of magnetic compound fluid (MCF) rubber as a haptic sensor for use as a material for robot sensors, artificial skin, and so on. MCF rubber is one of several new composite materials utilizing the MCF magnetic responsive fluid developed by Shimada. By applying MCF to silicon oil rubber, we can make MCF rubber highly sensitive to temperature and electric conduction. By mixing Cu and Ni particles in the silicon oil rubber and then applying a strong magnetic field, we can produce magnetic clusters at high density. The clusters form a network, as confirmed by optical observation. The MCF rubber with small deformations can act as an effective sensor. We report herein several experiments in which changes in the MCF rubber's resistance were observed when the rubber was compressed and a deformation was generated. We then made a trial haptic sensor using the MCF conductive rubber and performed many experiments to observe changes in the electrical resistance of the sensor. The experimental results showed that the proposed sensor made with MCF conductive rubber is useful for sensing small amounts of pressure or small deformations. Sometimes, however, the sensor rubber will be extended when we apply this sensor to the finger of the robot or an elbow. In these cases, it is necessary to understand the changes in sensor's conductivity. We therefore carried out some experiments to demonstrate how, under tensile conditions, the sensor's conductivity changes to a small value easier than the sensor in free condition. The results show that the sensors became more sensitive to the same pressure under extended conditions. In the present paper, we first describe the new type of functional fluid MCF rubber and a new composite material based on this MCF fluid. We then explain the production method for MCF conductive rubber and its conductive algorithm. Finally, we report our results regarding the MCF sensitivity when the MCF rubber was pulled. These experiments show an improvement in the sensitivity of the MCF rubber in the extended state.

Addition of Rubber to soil damages the functional diversity of soil.

PubMed

Goswami, Madhurankhi; Bhattacharyya, Purnita; Tribedi, Prosun

2017-07-01

Rubber is a polymer of isoprene, consisting mainly of cis-1,4-polyisoprene units. The unmanageable production and its irresponsible disposal pose severe threats to environmental ecology. Therefore, the current study focuses extensively on the ill-effects of Rubber disposal on soil microbial functional diversity as it reflects the health of ecosystem by acting as a key component in ecosystem productivity. To investigate the effect of Rubber on soil microbial functional diversity, soil samples were collected from landfill sites and three different soil microcosms (Rubber treated, untreated, and sterile soil) were prepared. The soil enzymatic activity was determined by fluorescein diacetate hydrolysis followed by the determination of the microbial metabolic potential and functional diversity by average well color development and Shannon-Weaver index (H), respectively. BiOLOG ECO plates were used for determining the microbial functional diversity of the soil microcosms. Higher heterotrophic microbial count as well as higher soil microbial activity was observed in Rubber untreated soil than Rubber treated soil microcosm. The result indicated that the addition of Rubber to soil reduced soil heterotrophic microbial count and soil microbial activity considerably. Similarly, soil microbial metabolic potential as well as microbial functional diversity of soil had been decreased by the addition of Rubber gloves in it. Variation in soil microbial metabolic spectrum between Rubber treated and untreated microcosm was confirmed by multivariate analysis. Collectively, all the results demonstrated that the addition of Rubber to soil reduced the soil microbial functional diversity considerably. Therefore, it is necessary for the commission of serious steps regarding Rubber disposal and protection of the environment from serious environmental issues.

Research on a haptic sensor made using MCF conductive rubber

NASA Astrophysics Data System (ADS)

Zheng, Yaoyang; Shimada, Kunio

2008-05-01

To provide a new composite material having a high electrical sensitivity in the fields of robotics and sensing, a magnetic rubber having network-like magnetic clusters was developed by utilizing a magnetic compound fluid (MCF). MCF rubber with small deformations can provide an effective sensor. In this paper, we report many experiments in which changes of the MCF rubber's resistance were observed when the rubber was compressed and a deformation was generated; we then made a trial haptic sensor using the MCF conductive rubber and performed many experiments to observe changes of the electrical resistance of the sensor. The results of experiments showed that the proposed sensor made with MCF conductive rubber is useful for sensing small amounts of pressure or small deformations.

Research on a haptic sensor made using MCF conductive rubber.

PubMed

Zheng, Yaoyang; Shimada, Kunio

2008-05-21

To provide a new composite material having a high electrical sensitivity in the fields of robotics and sensing, a magnetic rubber having network-like magnetic clusters was developed by utilizing a magnetic compound fluid (MCF). MCF rubber with small deformations can provide an effective sensor. In this paper, we report many experiments in which changes of the MCF rubber's resistance were observed when the rubber was compressed and a deformation was generated; we then made a trial haptic sensor using the MCF conductive rubber and performed many experiments to observe changes of the electrical resistance of the sensor. The results of experiments showed that the proposed sensor made with MCF conductive rubber is useful for sensing small amounts of pressure or small deformations.

Z-Pin Stubble Technology Advanced Research (ZSTAR)

DTIC Science & Technology

2008-04-01

2.3 MANUFACTURING WITH RUBBER SHEETS ...................................................................... 12 2.3.1 Rubber Sheet Material...17 2.3.6 Rubber Material Intact and Gripped ........................................................................ 17 2.3.7 Successful...0.125 inch Stubble Fabrication ............................................................... 17 2.3.8 Rubber Material Guidelines

The reclaiming of butyl rubber and in-situ compatibilization of thermoplastic elastomer by power ultrasound

NASA Astrophysics Data System (ADS)

Feng, Wenlai

This is a study of the continuous ultrasound aided extrusion process for the in-situ compatibilization of isotactic polypropylene (iPP)/ethylene-propylene diene rubber (EPDM) thermoplastic elastomer (TPE) using a newly developed ultrasonic treatment reactor. The rheological, mechanical properties and morphology of the TPE with and without ultrasonic treatment were studied. In-situ compatibilization in the ultrasonically treated blends was observed as evident by their more stable morphology after annealing, improved mechanical properties and IR spectra. The obtained results indicated that ultrasonic treatment induced the thermo-mechanical degradations and led to the possibility of enhanced molecular transport and chemical reactions at the interfaces. Processing conditions were established for enhanced in situ compatibilization of the PP/EPDM TPE. The ultrasonic treatments of butyl rubber gum and ultrasonic devulcanization of butyl rubber, tire-curing bladder during extrusion using a grooved barrel ultrasonic reactor were carried out. The ultrasonic treatment of gum caused degradation of the polymer main chain leading to lower molecular weight, broader molecular weight distribution, less unsaturation and changes in physical properties. The devulcanization of butyl rubber was successfully accomplished only at severe conditions of ultrasonic treatment. The mechanical properties of vulcanizates prepared from devulcanized butyl rubber are comparable to that of the virgin vulcanizate. The molecular characterization of sol fraction of devulcanized butyl rubber showed the devulcanization and degradation of butyl rubber occurred simultaneously. 1H NMR transverse relaxation was also used to study butyl rubber gum before and after ultrasonic treatment, and ultrasonically devulcanized unfilled butyl rubber. The T2 relaxation decays were successfully described using a two-component model. The recyclability of tire-curing bladder was also investigated. Gel fraction, crosslink density, cure behavior, dynamic properties and mechanical properties were measured. Good mechanical properties of revulcanized rubber were achieved by blending devulcanized rubber with the carbon black filled virgin butyl rubber. The structural characteristics of devulcanized butyl rubber were simulated using the Dobson-Gordon theory of rubber network statistics. A fairly good agreement between experimental data and theoretical prediction on normalized gel fraction vs. normalized crosslink density was achieved. The simulation of devulcanized butyl rubber indicated that the rate of crosslink rupture is much higher than that of the main chain.

Effect of vulcanization temperature and humidity on the properties of RTV silicone rubber

NASA Astrophysics Data System (ADS)

Wu, Xutao; Li, Xiuguang; Hao, Lu; Wen, Xishan; Lan, Lei; Yuan, Xiaoqing; Zhang, Qingping

2017-06-01

In order to study the difference in performance of room temperature vulcanized (RTV) silicone rubber in vulcanization environment with different temperature and humidity, static contact angle method, FTIR and TG is utilized to depict the properties of hydrophobicity, transfer of hydrophobicity, functional groups and thermal stability of RTV silicone rubber. It is found that different vulcanization conditions have effects on the characteristics of RTV silicone rubber, which shows that the hydrophobicity of RTV silicone rubber changes little with the vulcanization temperature but a slight increase with the vulcanization humidity. Temperature and humidity have obvious effects on the hydrophobicity transfer ability of RTV silicone rubber, which is better when vulcanization temperature is 5°C or vulcanization humidity is 95%. From the Fourier transform infrared spectroscopy, it can be concluded that humidity and temperature of vulcanization conditions have great effect on the functional groups of silicone rubber, and vulcanization conditions also have effect on thermal stability of RTV silicone rubber. When vulcanization temperature is 5°C or vulcanization humidity is 15% or 95%, the thermal stability of silicone rubber becomes worse.

The Effect of Particles on Electrolytically Polymerized Thin Natural MCF Rubber for Soft Sensors Installed in Artificial Skin

PubMed Central

Shimada, Kunio; Mochizuki, Osamu; Kubota, Yoshihiro

2017-01-01

The aim of this study is to investigate the effect of particles as filler in soft rubber sensors installed in artificial skin. We examine sensors made of natural rubber (NR-latex) that include magnetic particles of Ni and Fe3O4 using magnetic compound fluid (MCF). The 1-mm thickness of the electrolytically polymerized MCF rubber makes production of comparatively thin rubber sensors feasible. We first investigate the effect of magnetic particles Ni and Fe3O4 on the curing of MCF rubber. Next, in order to adjust the electric properties of the MCF rubber, we adopt Al2O3 dielectric particles. We investigate the effect of Al2O3 particles on changes in electric current, voltage and temperature of electrolytically polymerized MCF rubber liquid, and on the electric properties under the application of normal and shear forces. By adjusting the ratio of Ni, Fe3O4, Al2O3 and water in MCF rubber with Al2O3, it is possible to change the electric properties. PMID:28422061

36 CFR 261.70 - Issuance of regulations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... more of the following purposes: (1) Fire prevention or control. (2) Disease prevention or control. (3) Protection of property, roads, or trails. (4) Protection of threatened, endangered, rare, unique, or...

36 CFR 261.70 - Issuance of regulations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... more of the following purposes: (1) Fire prevention or control. (2) Disease prevention or control. (3) Protection of property, roads, or trails. (4) Protection of threatened, endangered, rare, unique, or...

36 CFR 261.70 - Issuance of regulations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... more of the following purposes: (1) Fire prevention or control. (2) Disease prevention or control. (3) Protection of property, roads, or trails. (4) Protection of threatened, endangered, rare, unique, or...

36 CFR 261.70 - Issuance of regulations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... more of the following purposes: (1) Fire prevention or control. (2) Disease prevention or control. (3) Protection of property, roads, or trails. (4) Protection of threatened, endangered, rare, unique, or...

On the wake flow of asymmetrically beveled trailing edges

NASA Astrophysics Data System (ADS)

Guan, Yaoyi; Pröbsting, Stefan; Stephens, David; Gupta, Abhineet; Morris, Scott C.

2016-05-01

Trailing edge and wake flows are of interest for a wide range of applications. Small changes in the design of asymmetrically beveled or semi-rounded trailing edges can result in significant difference in flow features which are relevant for the aerodynamic performance, flow-induced structural vibration and aerodynamically generated sound. The present study describes in detail the flow field characteristics around a family of asymmetrically beveled trailing edges with an enclosed trailing-edge angle of 25° and variable radius of curvature R. The flow fields over the beveled trailing edges are described using data obtained by particle image velocimetry (PIV) experiments. The flow topology for different trailing edges was found to be strongly dependent on the radius of curvature R, with flow separation occurring further downstream as R increases. This variation in the location of flow separation influences the aerodynamic force coefficients, which were evaluated from the PIV data using a control volume approach. Two-point correlations of the in-plane velocity components are considered to assess the structure in the flow field. The analysis shows large-scale coherent motions in the far wake, which are associated with vortex shedding. The wake thickness parameter yf is confirmed as an appropriate length scale to characterize this large-scale roll-up motion in the wake. The development in the very near wake was found to be critically dependent on R. In addition, high-speed PIV measurements provide insight into the spectral characteristics of the turbulent fluctuations. Based on the time-resolved flow field data, the frequency range associated with the shedding of coherent vortex pairs in the wake is identified. By means of time-correlation of the velocity components, turbulent structures are found to convect from the attached or separated shear layers without distinct separation point into the wake.

Non-linear controls influence functions in an aircraft dynamics simulator

NASA Technical Reports Server (NTRS)

Guerreiro, Nelson M.; Hubbard, James E., Jr.; Motter, Mark A.

2006-01-01

In the development and testing of novel structural and controls concepts, such as morphing aircraft wings, appropriate models are needed for proper system characterization. In most instances, available system models do not provide the required additional degrees of freedom for morphing structures but may be modified to some extent to achieve a compatible system. The objective of this study is to apply wind tunnel data collected for an Unmanned Air Vehicle (UAV), that implements trailing edge morphing, to create a non-linear dynamics simulator, using well defined rigid body equations of motion, where the aircraft stability derivatives change with control deflection. An analysis of this wind tunnel data, using data extraction algorithms, was performed to determine the reference aerodynamic force and moment coefficients for the aircraft. Further, non-linear influence functions were obtained for each of the aircraft s control surfaces, including the sixteen trailing edge flap segments. These non-linear controls influence functions are applied to the aircraft dynamics to produce deflection-dependent aircraft stability derivatives in a non-linear dynamics simulator. Time domain analysis of the aircraft motion, trajectory, and state histories can be performed using these nonlinear dynamics and may be visualized using a 3-dimensional aircraft model. Linear system models can be extracted to facilitate frequency domain analysis of the system and for control law development. The results of this study are useful in similar projects where trailing edge morphing is employed and will be instrumental in the University of Maryland s continuing study of active wing load control.

Exploring the TRAILs less travelled: TRAIL in cancer biology and therapy.

PubMed

von Karstedt, Silvia; Montinaro, Antonella; Walczak, Henning

2017-05-24

The discovery that the tumour necrosis factor-related apoptosis-inducing ligand (TRAIL) can induce apoptosis of cancer cells without causing toxicity in mice has led to the in-depth study of pro-apoptotic TRAIL receptor (TRAIL-R) signalling and the development of biotherapeutic drug candidates that activate TRAIL-Rs. The outcome of clinical trials with these TRAIL-R agonists has, however, been disappointing so far. Recent evidence indicates that many cancers, in addition to being TRAIL resistant, use the endogenous TRAIL-TRAIL-R system to their own advantage. However, novel insight on two fronts - how resistance of cancer cells to TRAIL-based pro-apoptotic therapies might be overcome, and how the pro-tumorigenic effects of endogenous TRAIL might be countered - gives reasonable hope that the TRAIL system can be harnessed to treat cancer. In this Review we assess the status quo of our understanding of the biology of the TRAIL-TRAIL-R system - as well as the gaps therein - and discuss the opportunities and challenges in effectively targeting this pathway.

REACTOR COOLANT TUBE SEAL

DOEpatents

Morris, W.J.

1958-12-01

A plle-flattenlng control element and a fluid seal therefore to permit movement of the element into a liquld contnining region of a neutronlc reactor are described. The device consists of flattened, thin-walled aluminum tubing contalnlng a uniform mixture of thermal neutron absorbing material, and a number of soft rubber closures for the process tubes, having silts capable of passing the flattened elements therethrough, but effectively sealing the process tubes against fluld leaknge by compression of the rubber. The flattened tubing is sufficiently flexible to enable it to conform to the configuratlon of the annular spacing surrounding the fuel elements ln the process tubes.

48 CFR 225.370-4 - Policy.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., acoustic hailing devices, electromuscular TASER guns, blunt-trauma devices like rubber balls and sponge grenades, and a variety of other riot control agents and delivery systems) are employed by personnel...

Argentine ant trail pheromone disruption is mediated by trail concentration.

PubMed

Suckling, David Maxwell; Stringer, Lloyd D; Corn, Joshua E

2011-10-01

Argentine ant trail pheromone disruption, using continuous release of the trail pheromone compound (Z)-9-hexadecanal, reduces the incidence of trails and foraging rates of field populations. However, little is known about the concentrations of pheromone required for successful disruption. We hypothesized that higher pheromone quantities would be necessary to disrupt larger ant populations. To test this, we laid a 30-cm long base trail of (Z)-9-hexadecanal on a glass surface at low and high rates (1 and 100 pg/cm) (Trail 1), and laid a second, shorter trail (Trail 2, 10 cm long, located 1.5 cm upwind) near the middle of Trail 1 at six rates (1, 10, 100, 1,000, 10,000, and 100,000 pg/cm). We then recorded and digitized movements of individual ants following Trail 1, and derived a regression statistic, r (2), as an index of trail integrity, and also recorded arrival success at the other end of the trail (30 cm) near a food supply. Disruption of trails required 100 fold more pheromone upwind, independent of base-trail concentration. This implies that in the field, trail disruption is likely to be less successful against high ant-trail densities (greater concentration of trail pheromone), and more successful against newly formed or weak trails, as could be expected along invasion fronts.

Tunable-focus liquid lens controlled using a servo motor

NASA Astrophysics Data System (ADS)

Ren, Hongwen; Fox, David; Anderson, P. Andrew; Wu, Benjamin; Wu, Shin-Tson

2006-09-01

We demonstrated a liquid lens whose focal length can be controlled by an actuator. The lens cell is composed of elastic membrane, planar glass plate, a periphery sealing ring, and a liquid with a fixed volume in the lens chamber. Part of the periphery sealing ring is excavated to form a hollow chamber which functions as a reservoir. This hollowed periphery is surrounded by an exterior rubber membrane. The shaft of an actuator is used to deform the elastic rubber. Squeezing the liquid contained in the reservoir into the lens chamber. Excess liquid in the lens chamber will push the lens membrane to outward, resulting in a lens shape change. Due to the compact structure and easy operation, this liquid lens has potential applications in zoom lenses, auto beam steering, and eyeglasses.

Characterization of asphalt cements modified with crumbed rubber from discarded tires : final report.

DOT National Transportation Integrated Search

1994-11-01

The potential legislative requirement for incorporation of scrap rubber into asphalt blends mandated a thorough evaluation of the influence of scrap rubber additives on the physical properties and aging characteristics of rubber/asphalt blends. Blend...

Investigation to Identify Performance Criteria and Test Methods for Evaluating Single-Ply Roofing Systems.

DTIC Science & Technology

1987-03-01

Reinforced Black EPDM Rubber Sheets for Use in Roofing Applications ( Rubber Manufacturers Association [RMAJ, 1984). Minimum Requirements for Fabric-Reinforced...Black Polychloroprene Rubber Sheets for Use in Roofing Applications (RMA, 1984). Minimum Requirements for Non-Reinforced Black EPDM Rubber Sheets for...and materials. The Rubber Manufacturers Amoeiation (RMA) (USA) RMA is funding a study in conjunction with ASTM to evaluate three different EPDM

Investigation of surface halide modification of nitrile butadiene rubber

NASA Astrophysics Data System (ADS)

Sukhareva, K. V.; Mikhailov, I. A.; Andriasyan, Yu O.; Mastalygina, E. E.; Popov, A. A.

2017-12-01

The investigation is devoted to the novel technology of surface halide modification of rubber samples based on nitrile butadiene rubber (NBR). 1,1,2-trifluoro-1,2,2-trichlorethane was used as halide modifier. The developed technology is characterized by production stages reduction to one by means of treating the rubber compound with a halide modifier. The surface halide modification of compounds based on nitrile butadiene rubber (NBR) was determined to result in increase of resistance to thermal oxidation and aggressive media. The conducted research revealed the influence of modification time on chemical resistance and physical-mechanical properties of rubbers under investigation.

The use of smoke acid as an alternative coagulating agent for natural rubber sheets' production.

PubMed

Ferreira, Vanda S; Rêgo, Ione N C; Pastore, Floriano; Mandai, Mariana M; Mendes, Leonardo S; Santos, Karin A M; Rubim, Joel C; Suarez, Paulo A Z

2005-03-01

A comparative study of rubber sheets obtained using formic, acetic, and smoke acid as coagulants is shown for latex obtained from native Amazonian trees and also from commercial cultivated trees. The evaluation of both processes of coagulation was carried out by spectroscopic and physical-chemical analysis, showing no differences in the rubber sheets obtained. This new method of rubber sheet preparation was introduced into Amazonian rainforest rubber tapper communities, which are actually producing in large scale. The physical-mechanical properties were similar among a large sheets made by different rubber tapper communities using this new method.

FTIR spectra and mechanical strength analysis of some selected rubber derivatives.

PubMed

Gunasekaran, S; Natarajan, R K; Kala, A

2007-10-01

Rubber materials have wide range of commercial applications such as, infant diapers, famine hygiene products, drug delivery devices and incontinency products such as rubber tubes, tyres, etc. In the present work, studies on mechanical properties of some selected rubber materials viz., natural rubber (NR), styrene butadiene rubber (SBR), nitrile butadiene rubber (NBR) and ethylene propylene diene monomer (EPDM) have been carried out in three states viz., raw, vulcanized and reinforced. To enhance the quality of rubber elastomers, an attempt is made to prepare new elastomers called polyblends. In the present study an attempt is made to blend NR with NBR and with EPDM. We here report, a novel approach for the evaluation of various physico-mechanical properties such as mechanical strength, tensile strength, elongation and hardness. The method is simple, direct and fast and involves infrared spectral measurements for the evaluation of these properties. With the applications of modern infrared spectroscopy, the mechanical strength of these rubber materials have been analyzed by calculating the internal standards among the methyl and methylene group vibrational frequencies obtained from FTIR spectroscopy. Also the tensile strength measurements carried out by universal testing machine. The results pertaining physico-mechanical properties of the rubber derivatives undertaken in the present study obtained by IR-based method are in good agreement with data resulted from the standard methods.

FTIR spectra and mechanical strength analysis of some selected rubber derivatives

NASA Astrophysics Data System (ADS)

Gunasekaran, S.; Natarajan, R. K.; Kala, A.

2007-10-01

Rubber materials have wide range of commercial applications such as, infant diapers, famine hygiene products, drug delivery devices and incontinency products such as rubber tubes, tyres, etc. In the present work, studies on mechanical properties of some selected rubber materials viz., natural rubber (NR), styrene butadiene rubber (SBR), nitrile butadiene rubber (NBR) and ethylene propylene diene monomer (EPDM) have been carried out in three states viz., raw, vulcanized and reinforced. To enhance the quality of rubber elastomers, an attempt is made to prepare new elastomers called polyblends. In the present study an attempt is made to blend NR with NBR and with EPDM. We here report, a novel approach for the evaluation of various physico-mechanical properties such as mechanical strength, tensile strength, elongation and hardness. The method is simple, direct and fast and involves infrared spectral measurements for the evaluation of these properties. With the applications of modern infrared spectroscopy, the mechanical strength of these rubber materials have been analyzed by calculating the internal standards among the methyl and methylene group vibrational frequencies obtained from FTIR spectroscopy. Also the tensile strength measurements carried out by universal testing machine. The results pertaining physico-mechanical properties of the rubber derivatives undertaken in the present study obtained by IR-based method are in good agreement with data resulted from the standard methods.

The outgassing characteristic research of the silicone rubber in high power laser system

NASA Astrophysics Data System (ADS)

Wu, Qipeng; Lv, Haibing; Dong, Meng; Fu, Zhaohui

2016-11-01

The outgassing characteristic of the silicone rubber which is the main material of non-metallic materials in high power laser system was studied outgassing rates of the silicone rubber and the baked-out silicone rubber which was performed at 80°C4 hours were measured by the constant volume process method and outgassing properties of them were analyzed by the quadrupole mass spectrometer. The results show that the outgassing rate of the silicone rubber and the baked-out silicone rubber is 2.69×10-7 Pa·m3s-1cm-2 and 6.47×10-8 Pa·m3s-1cm-2 respectively. All of them give out condensable volatile matter in vacuum. The outgassing rate and condensable volatile matter of the baked-out silicone rubber are less an order of magnitude compared with the silicone rubber, and the outgassing rate of the silicone rubber is less than 1×10-7 Pa·m3s-1cm-2, which is fit for non-metallic material of the high power laser system. This paper also discusses the method of reducing the outgassing rate and condensable volatile matter of the silicone rubber in high power laser system.

Comprehensive Proteomics Analysis of Laticifer Latex Reveals New Insights into Ethylene Stimulation of Natural Rubber Production.

PubMed

Wang, Xuchu; Wang, Dan; Sun, Yong; Yang, Qian; Chang, Lili; Wang, Limin; Meng, Xueru; Huang, Qixing; Jin, Xiang; Tong, Zheng

2015-09-08

Ethylene is a stimulant to increase natural rubber latex. After ethylene application, both fresh yield and dry matter of latex are substantially improved. Moreover, we found that ethylene improves the generation of small rubber particles. However, most genes involved in rubber biosynthesis are inhibited by exogenous ethylene. Therefore, we conducted a proteomics analysis of ethylene-stimulated rubber latex, and identified 287 abundant proteins as well as 143 ethylene responsive latex proteins (ERLPs) with mass spectrometry from the 2-DE and DIGE gels, respectively. In addition, more than 1,600 proteins, including 404 ERLPs, were identified by iTRAQ. Functional classification of ERLPs revealed that enzymes involved in post-translational modification, carbohydrate metabolism, hydrolase activity, and kinase activity were overrepresented. Some enzymes for rubber particle aggregation were inhibited to prolong latex flow, and thus finally improved latex production. Phosphoproteomics analysis identified 59 differential phosphoproteins; notably, specific isoforms of rubber elongation factor and small rubber particle protein that were phosphorylated mainly at serine residues. This post-translational modification and isoform-specific phosphorylation might be important for ethylene-stimulated latex production. These results not only deepen our understanding of the rubber latex proteome but also provide new insights into the use of ethylene to stimulate rubber latex production.

RoxB Is a Novel Type of Rubber Oxygenase That Combines Properties of Rubber Oxygenase RoxA and Latex Clearing Protein (Lcp).

PubMed

Birke, Jakob; Röther, Wolf; Jendrossek, Dieter

2017-07-15

Only two types of rubber oxygenases, rubber oxygenase (RoxA) and latex clearing protein (Lcp), have been described so far. RoxA proteins (RoxAs) are c -type cytochromes of ≈70 kDa produced by Gram-negative rubber-degrading bacteria, and they cleave polyisoprene into 12-oxo-4,8-dimethyltrideca-4,8-diene-1-al (ODTD), a C 15 oligo-isoprenoid, as the major end product. Lcps are common among Gram-positive rubber degraders and do not share amino acid sequence similarities with RoxAs. Furthermore, Lcps have much smaller molecular masses (≈40 kDa), are b -type cytochromes, and cleave polyisoprene to a mixture of C 20 , C 25 , C 30 , and higher oligo-isoprenoids as end products. In this article, we purified a new type of rubber oxygenase, RoxB Xsp (RoxB of Xanthomonas sp. strain 35Y). RoxB Xsp is distantly related to RoxAs and resembles RoxAs with respect to molecular mass (70.3 kDa for mature protein) and cofactor content (2 c -type hemes). However, RoxB Xsp differs from all currently known RoxAs in having a distinctive product spectrum of C 20 , C 25 , C 30 , and higher oligo-isoprenoids that has been observed only for Lcps so far. Purified RoxB Xsp revealed the highest specific activity of 4.5 U/mg (at 23°C) of all currently known rubber oxygenases and exerts a synergistic effect on the efficiency of polyisoprene cleavage by RoxA Xsp RoxB homologs were identified in several other Gram-negative rubber-degrading species, pointing to a prominent function of RoxB for the biodegradation of rubber in Gram-negative bacteria. IMPORTANCE The enzymatic cleavage of rubber (polyisoprene) is of high environmental importance given that enormous amounts of rubber waste materials are permanently released (e.g., by abrasion of tires). Research from the last decade has discovered rubber oxygenase A, RoxA, and latex clearing protein (Lcp) as being responsible for the primary enzymatic attack on the hydrophobic and water-insoluble biopolymer poly( cis -1,4-isoprene) in Gram-negative and Gram-positive rubber-degrading bacteria, respectively. Here, we provide evidence that a third type of rubber oxygenase is present in Gram-negative rubber-degrading species. Due to its characteristics, we suggest the designation RoxB for the new type of rubber oxygenase. Bioinformatic analysis of genome sequences indicates the presence of roxB homologs in other Gram-negative rubber degraders. Copyright © 2017 American Society for Microbiology.

Pre-test data and lessons learned from a group research project examining changes in physical activity behavior following construction of a rails-to-trails facility.

PubMed

Chatfield, Sheryl L; Mumaw, Elizabeth; Davis, T; Hallam, Jeffrey S

2014-04-01

Built environments in rural settings may provide greater challenges than those in urban settings due to physical characteristics inherent to low-density population areas. Multiuse recreational trails, such as those that repurpose abandoned railroad lines, may provide a physical activity resource that is well suited to rural areas. However, the direct impact of trail availability on physical activity behavior is not generally known because it is unclear whether activity reported in most trail research represents increases in physical activity or displacement of activity in individuals who previously exercised in other locations. This research, initiated by a group of students in a graduate seminar, represents to our knowledge, the first instance in which PA was assessed prior to the availability of an entirely new rails-to-trails facility. The research was implemented using a nonequivalent dependent variable design to counter the lack of a control group; the nonequivalent dependent variable chosen was weekly servings of fruit and vegetables. Participants responding to intercept interviews classified days of activity during the prior week as mild, moderate or vigorous. Baseline results for 244 participants suggested generally low levels of activity prior to trail availability; number of reported days of activity decreased with described intensity. We also discuss several issues encountered in planning and implementing this group project including those related to data collection, variable levels of commitment among student members, and inconsistent project management, and offer potential solutions to these concerns.

Applicability of Landsat TM data for inventorying and monitoring of rubber (Hevea brasiliensis) plantations in Selangor, Malaysia: Linkages to policies

NASA Astrophysics Data System (ADS)

Suratman, Mohd Nazip

2003-06-01

Rubber tree (Hevea brasiliensis (Wild ex Adr. De Juss) Muell Arg.) plantations in Malaysia are important sources of natural rubber and wood products. Effective management and appropriate policy for these resources require reliable information on resource dynamics and forecasts of resource availability. The need for inventories and monitoring systems prompted this research into utilising ground information and satellite imagery for developing methods for forest plantation inventory. Monitoring procedures were developed using three dates of Landsat Thematic Mapper (TM) imagery. The specific objectives of the research were: (1) to develop an effective method for inventorying rubber tree plantations using an appropriate combination of satellite imagery and ground sampling in the State of Selangor, Malaysia; (2) to demonstrate the application of a Landsat TM-based rubber volume model in an extended area of rubber plantations south of Kuala Lumpur (KL), Malaysia; (3) to develop an operational methodology for monitoring land use/cover change, with a primary focus on rubber plantations; and (4) to identify relationships between the primary drivers of resource change and policies, and examine the evidence of policies---rubber area change linkages in the study area. Reasonably accurate predictions of the volume, age, and area of rubber plantations were obtained from Landsat TM data. The use of supervised image classification and an image segmentation approach for rubber volume model application showed better performance for volume prediction than a combined land use/cover and rubber volume classification technique, thus providing a useful tool for displaying rubber stand volume within segments or spatial units across the landscape. The combined use of a time series of Landsat TM imagery, modified postclassification change detection, and geographic information system (GIS) techniques made it possible to produce land use/cover change matrices and rubber area change information, thus helping to understand the dynamics of the rubber tree resource. The decrease in the area of rubber plantations and the increase in the area of mixed crops from 1989--1993 in south of KL were partly attributed to the adoption of a crop diversification policy which was driven by relatively poor natural rubber prices during that time. The decrease in the areas of rubber plantations from 1993--1999 in this area was primarily due to rapid urbanization and infrastructure development driven by demographic expansion in the area south of KL. This thesis makes a practical contribution to the development of methods for inventory of forest plantations by linking ground information with model projections based on satellite data. Additionally, the thesis demonstrates the development of monitoring tools to assess resource availability and variability over time, and establish its linkages to policies. The inventory information, models, and monitoring protocols are needed for effective resource management planning aimed at maximizing the potential benefits of rubber tree crops for wood and natural rubber supply in Malaysia.

Computational Test Cases for a Clipped Delta Wing with Pitching and Trailing-Edge Control Surface Oscillations

NASA Technical Reports Server (NTRS)

Bennett, Robert M.; Walker, Charlotte E.

1999-01-01

Computational test cases have been selected from the data set for a clipped delta wing with a six-percent-thick circular-arc airfoil section that was tested in the NASA Langley Transonic Dynamics Tunnel. The test cases include parametric variation of static angle of attack, pitching oscillation frequency, trailing-edge control surface oscillation frequency, and Mach numbers from subsonic to low supersonic values. Tables and plots of the measured pressures are presented for each case. This report provides an early release of test cases that have been proposed for a document that supplements the cases presented in AGARD Report 702.

Abscisic acid-dependent regulation of small rubber particle protein gene expression in Taraxacum brevicorniculatum is mediated by TbbZIP1.

PubMed

Fricke, Julia; Hillebrand, Andrea; Twyman, Richard M; Prüfer, Dirk; Schulze Gronover, Christian

2013-04-01

Natural rubber is a high-molecular-mass biopolymer found in the latex of >2,500 plant species, including Hevea brasiliensis, Parthenium argentatum and Taraxacum spp. The active sites of rubber biosynthesis are rubber particles, which comprise a hydrophobic rubber core surrounded by a phospholipid monolayer membrane containing species-dependent lipids and associated proteins. Small rubber particle proteins are the most abundant rubber particle-associated proteins in Taraxacum brevicorniculatum (TbSRPPs) and may promote rubber biosynthesis by stabilizing the rubber particle architecture. We investigated the transcriptional regulation of genes encoding SRPPs and identified a bZIP transcription factor (TbbZIP.1) similar to the Arabidopsis thaliana ABI5-ABF-AREB subfamily, which is thought to include downstream targets of ABA and/or abiotic stress-inducible protein kinases. The TbbZIP.1 gene was predominantly expressed in laticifers and regulates the expression of TbSRPP genes in an ABA-dependent manner. The individual TbSRPP genes showed distinct induction profiles, suggesting diverse roles in rubber biosynthesis and stress adaptation. The potential involvement of TbSRPPs in the adaptation of T. brevicorniculatum plants to environmental stress is discussed based on our current knowledge of the stress-response roles of SRPPs and their homologs, and the protective function of latex and rubber against pathogens. Our data suggest that TbSRPPs contribute to stress tolerance in T. brevicorniculatum and that their effects are mediated by TbbZIP.1.

PEO Ammunition Systems Portfolio Book 2012-2013

DTIC Science & Technology

2011-02-02

assembly. Aluminum ogive contains firing pin, a rubber anti-creep spring and M550 fuze escapement assembly and is threaded to projectile body...51 The Mortar Weapons and Fire Control Family M95/M96 Mortar Fire Control System (MFCS) – Mounted...52 M150/M151 Mortar Fire Control System Dismounted (MFCS-D

Exploring the neural substrates of attentional control and human intelligence: Diffusion tensor imaging of prefrontal white matter tractography in healthy cognition.

PubMed

Ohtani, Toshiyuki; Nestor, Paul G; Bouix, Sylvain; Newell, Dominick; Melonakos, Eric D; McCarley, Robert W; Shenton, Martha E; Kubicki, Marek

2017-01-26

We combined diffusion tension imaging (DTI) of prefrontal white matter integrity and neuropsychological measures to examine the functional neuroanatomy of human intelligence. Healthy participants completed the Wechsler Adult Intelligence Scale-Third Edition (WAIS-III) along with neuropsychological tests of attention and executive control, as measured by Trail Making Test (TMT) and Wisconsin Card Sorting Test (WCST). Stochastic tractography, considered the most effective DTI method, quantified white matter integrity of the medial orbital frontal cortex (mOFC) and rostral anterior cingulate cortex (rACC) circuitry. Based on prior studies, we hypothesized that posterior mOFC-rACC connections may play a key structural role linking attentional control processes and intelligence. Behavioral results provided strong support for this hypothesis, specifically linking attentional control processes, measured by Trails B and WCST perseverative errors, to intelligent quotient (IQ). Hierarchical regression results indicated left posterior mOFC-rACC fractional anisotropy (FA) and Trails B performance time, but not WCST perseverative errors, each contributed significantly to IQ, accounting for approximately 33.95-51.60% of the variance in IQ scores. These findings suggested that left posterior mOFC-rACC white matter connections may play a key role in supporting the relationship of executive functions of attentional control and general intelligence in healthy cognition. Copyright © 2016. Published by Elsevier Ltd.

Methacrylamide grafted elastomer composites reinforced with biobased particles

USDA-ARS?s Scientific Manuscript database

Modulus of rubber can be improved with grafting of unsaturated monomers. To increase the modulus of bio-based rubber composites, methacrylamide was grafted onto natural rubber composites reinforced with bio-based hydrophilic particles. Rubber particles in water were modified with methacrylamide usin...

Interaggregate Interaction in Filled Rubber

DTIC Science & Technology

1989-01-01

from a black masterbatch (Carbomix 1848 from the Copolymer Rubber and Chemical Corporation). The masterbatch was unmilled (SBR-83-0), passed 5 times...Vanderbilt Company) 3 97% 1,2-polybutadiene (Firestone Tire and Rubber Company) 4 Carbomix 1848 Masterbatch (Copolymer Rubber and Chemical Corporation) 14

75 FR 38119 - Polychloroprene Rubber From Japan

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-01

... Rubber From Japan AGENCY: United States International Trade Commission. ACTION: Institution of a five-year review concerning the antidumping duty finding on polychloroprene rubber from Japan. SUMMARY: The... on polychloroprene rubber from Japan would be likely to lead to continuation or recurrence of...

Use of scrap tire rubber : state of the technology and best practices.

DOT National Transportation Integrated Search

2005-02-01

The California Department of Transportation (Caltrans) has been using scrap tire rubber (called crumb : rubber modifier (CRM)) in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized : asphalt concrete (RAC). The performance of...

Prognostic value of tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and TRAIL receptors in renal cell cancer.

PubMed

Macher-Goeppinger, Stephan; Aulmann, Sebastian; Tagscherer, Katrin E; Wagener, Nina; Haferkamp, Axel; Penzel, Roland; Brauckhoff, Antje; Hohenfellner, Markus; Sykora, Jaromir; Walczak, Henning; Teh, Bin T; Autschbach, Frank; Herpel, Esther; Schirmacher, Peter; Roth, Wilfried

2009-01-15

The death ligand tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and its receptors (TRAIL-R) are involved in immune surveillance and tumor development. Here, we studied a possible association between the expression of TRAIL/TRAIL-Rs and the prognosis in patients with renal cell carcinomas (RCC). A tissue microarray containing RCC tumor tissue samples and corresponding normal tissue samples from 838 patients was generated. Expression of TRAIL and TRAIL-Rs was examined by immunohistochemistry and the effect of TRAIL and TRAIL-R expression on disease-specific survival was assessed. High TRAIL-R2 expression levels were associated with high-grade RCCs (P < 0.001) and correlated negatively with disease-specific survival (P = 0.01). Similarly, high TRAIL expression was associated with a shorter disease-specific survival (P = 0.01). In contrast, low TRAIL-R4 expression was associated with high-stage RCCs (P < 0.001) as well as with the incidence of distant metastasis (P = 0.03) and correlated negatively with disease-specific survival (P = 0.02). In patients without distant metastasis, multivariate Cox regression analyses revealed that TRAIL-R2 and TRAIL are independent prognostic factors for cancer-specific survival (in addition to tumor extent, regional lymph node metastasis, grade of malignancy, and type of surgery). High TRAIL-R2, high TRAIL, and low TRAIL-R4 expression levels are associated with a worse disease-specific survival in patients with RCCs. Therefore, the assessment of TRAIL/TRAIL-R expression offers valuable prognostic information that could be used to select patients for adjuvant therapy studies. Moreover, our findings are of relevance for a potential experimental therapeutic administration of TRAIL-R agonists in patients with RCCs.

Active flow control for a blunt trailing edge profiled body

NASA Astrophysics Data System (ADS)

Naghib Lahouti, Arash

Flow in the wake of nominally two-dimensional bluff bodies is dominated by vortex shedding, beyond a very small threshold Reynolds number. Vortex shedding poses challenges in the design of structures, due to its adverse effects such as cyclic aerodynamic loads and fatigue. The wake vortices are often accompanied by large- and small-scale secondary instabilities, which manifest as dislocations in the primary wake vortices, and/or pairs of counter-rotating streamwise vortices, depending on the dominant instability mode(s), which in turn depends on the profile geometry and Reynolds number. The secondary instabilities interact with the wake vortices through several mechanisms. Therefore, manipulation of the secondary instabilities can be used as a means to alter the wake vortices, in order to reduce their adverse effects. In the present study, flow in the wake of a blunt trailing edge profiled body, composed of an elliptical leading edge and a rectangular trailing edge, has been studied at Reynolds numbers ranging from Re(d) = 500 to 2150 where d is thickness of the body, to identify the secondary instabilities. Various tools, including numerical simulations, Laser Induced Fluorescence (LIF), and Particle Image Velocimetry (PIV) have been used for this study. Proper Orthogonal Decomposition (POD) has been applied to analyze the velocity field data. The results indicate the existence of small-scale instabilities with a spanwise wavelength of 2.0d to 2.5d in the near wake. The mechanism of the instability is similar to the Mode-A instability of a circular cylinder; however, it displays features that are specific to the blunt trailing edge profiled body. An active three-dimensional flow control mechanism based on the small-scale instabilities has been designed and evaluated. The mechanism comprises a series of trailing edge injection ports, with a spanwise spacing equal to the wavelength of the small-scale instabilities. Following preliminary evaluation of the control mechanism through numerical simulations, and experimental study of the effect of injection flow rate, extensive PIV experiments have been conducted to investigate the effectiveness of the flow control mechanism, and its effects on the wake flow structure, at Reynolds numbers ranging from Re(d ) = 700 to 1980. Measurements have been carried out at multiple spanwise locations, to establish a comprehensive image of the effect of the flow control mechanism on parameters such as drag force, wake width, and formation length. POD analysis and frequency spectrums are used to describe the process by which the mechanism affects the wake parameters and drag force. The results indicate that the flow control mechanism is able to reduce drag force by 10%. It is also shown that the best effectiveness in terms of suppression of the drag component resulting from velocity fluctuations is achieved when the flow control actuation wavelength closely matches the wavelength of the small-scale instabilities. KEYWORDS: Blunt Trailing Edge Profiled Body, Vortex Shedding, Wake Instability, Streamwise Vortex, Flow Control, Drag Reduction, Particle Image Velocimetry (PIV), Laser Induced Fluorescence (LIF), Flow Visualization, Numerical Simulation

Nonlinear aeroservoelastic analysis of a controlled multiple-actuated-wing model with free-play

NASA Astrophysics Data System (ADS)

Huang, Rui; Hu, Haiyan; Zhao, Yonghui

2013-10-01

In this paper, the effects of structural nonlinearity due to free-play in both leading-edge and trailing-edge outboard control surfaces on the linear flutter control system are analyzed for an aeroelastic model of three-dimensional multiple-actuated-wing. The free-play nonlinearities in the control surfaces are modeled theoretically by using the fictitious mass approach. The nonlinear aeroelastic equations of the presented model can be divided into nine sub-linear modal-based aeroelastic equations according to the different combinations of deflections of the leading-edge and trailing-edge outboard control surfaces. The nonlinear aeroelastic responses can be computed based on these sub-linear aeroelastic systems. To demonstrate the effects of nonlinearity on the linear flutter control system, a single-input and single-output controller and a multi-input and multi-output controller are designed based on the unconstrained optimization techniques. The numerical results indicate that the free-play nonlinearity can lead to either limit cycle oscillations or divergent motions when the linear control system is implemented.

Correlates of Trail Use for Recreation and Transportation on 5 Massachusetts Trails.

PubMed

Orstad, Stephanie L; McDonough, Meghan H; Klenosky, David B; Mattson, Marifran; Troped, Philip J

2016-08-01

Promoting use of community trails is a recommended strategy for increasing population levels of physical activity. Correlates of walking and cycling for recreation or transportation differ, though few studies have compared correlates of trail-based physical activity for recreation and transportation purposes. This study examined associations of demographic, social, and perceived built environmental factors with trail use for recreation and transportation and whether associations were moderated by age, gender, and prior trail use. Adults (N = 1195) using 1 of 5 trails in Massachusetts responded to an intercept survey. We used multiple linear and logistic regression models to examine associations with trail use. Respondents' mean age was 44.9 years (standard deviation = 12.5), 55.3% were female, and 82.0% were white. Age (longer-term users only), trail use with others, travel time to the trail, and trail design were significantly associated with use for recreation (P < .05). Age, gender, trail safety (longer-term users only), travel time to the trail, trail design (younger users only), and trail beauty were associated with use for transportation (P < .05). Some common correlates were found for recreational and transportation trail use, whereas some variables were uniquely associated with use for 1 purpose. Tailored strategies are suggested to promote trail use for recreation and transportation.

Slipping through the Cracks: Rubber Plantation Is Unsuitable Breeding Habitat for Frogs in Xishuangbanna, China

PubMed Central

Behm, Jocelyn E.; Yang, Xiaodong; Chen, Jin

2013-01-01

Conversion of tropical forests into agriculture may present a serious risk to amphibian diversity if amphibians are not able to use agricultural areas as habitat. Recently, in Xishuangbanna Prefecture, Yunnan Province – a hotspot of frog diversity within China – two-thirds of the native tropical rainforests have been converted into rubber plantation agriculture. We conducted surveys and experiments to quantify habitat use for breeding and non-breeding life history activities of the native frog species in rainforest, rubber plantation and other human impacted sites. Rubber plantation sites had the lowest species richness in our non-breeding habitat surveys and no species used rubber plantation sites as breeding habitat. The absence of breeding was likely not due to intrinsic properties of the rubber plantation pools, as our experiments indicated that rubber plantation pools were suitable for tadpole growth and development. Rather, the absence of breeding in the rubber plantation was likely due to a misalignment of breeding and non-breeding habitat preferences. Analyses of our breeding surveys showed that percent canopy cover over pools was the strongest environmental variable influencing breeding site selection, with species exhibiting preferences for pools under both high and low canopy cover. Although rubber plantation pools had high canopy cover, the only species that bred in high canopy cover sites used the rainforest for both non-breeding and breeding activities, completing their entire life cycle in the rainforest. Conversely, the species that did use the rubber plantation for non-breeding habitat preferred to breed in low canopy sites, also avoiding breeding in the rubber plantation. Rubber plantations are likely an intermediate habitat type that ‘slips through the cracks’ of species habitat preferences and is thus avoided for breeding. In summary, unlike the rainforests they replaced, rubber plantations alone may not be able to support frog populations. PMID:24040026

Trail Transect: A Method for Documenting Trail Changes

Treesearch

R.E. Leonard; A.M. Whitney

1977-01-01

A trail transect that documents trail conditions and changes in trails has been used successfully over the past 3 years to measure soil loss, and changes in trail width and vegetation. The system also can be used to study the relationship between trail degradation and the physical characteristics of the site. Data from trail transects can be useful in determining the...

Guide to Camouflage for DARCOM Equipment Developers

DTIC Science & Technology

1978-04-29

the trails by dragging devices, etc., can delay recognition of a tracked- veicle trail. A missile system, having fixed physical characteristics which...systems applicable to surface-to-air, air-to-air, and air-to-surface missiles. Sensors in the 0.2 to 0.4 and 1.0 to 5.0 micron bands are hybrid ...a wide variety of ultra- violet, visible and near infrared sensor systems. Actual sensors are hybrid computer controlled in six degrees-of-freedom

[Contemporary state of work conditions and occupational morbidity of workers engaged into rubber, mechanical rubber and tire industries].

PubMed

Stepanov, E G; Galiullina, É F; Samsonov, V M; Kudriavtsev, V P; Davletgareeva, G R; Shakirova, É D; Khasanov, B G; Buliakov, R T; Kamilov, R F; Shakirov, D F

2014-01-01

Based on analysis of materials provided by occupational safety department PC "UZEMiK" and JSC "Kauchuk", the authors evaluate contemporary work conditions and occupational morbidity in workers engaged into rubber, mechanical rubber and tyre industries.

Enhancing and standardizing interaction of rubber particles with asphalt : final report.

DOT National Transportation Integrated Search

1995-11-01

Addition of ground rubber particles to asphalt can enhance several fold the stiffness of the blend as reflected by G*/sin of the rubber-asphalt cements (RACs). Pretreatment of rubber particles with as little as 5% aromatic oil (AO) enhances the ap...

Magnesium affects rubber biosynthesis and particle stability in Ficus elastica, Hevea brasiliensis and Parthenium argentatum

USDA-ARS?s Scientific Manuscript database

Natural rubber biosynthesis occurs in laticifers of Ficus elastica and Hevea brasiliensis, and in parenchyma cells of Parthenium argentatum. Natural rubber is synthesized by rubber transferase using allylic pyrophosphates as initiators, isopentenyl pyrophosphate as monomeric substrate and magnesium ...

78 FR 39633 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-02

...We propose to supersede three existing airworthiness directives (ADs) that apply to The Boeing Company Model 757-200, - 200PF, and -200CB series airplanes. The existing ADs currently require repetitive inspections and audible tap tests of the upper and lower skins of the trailing edge wedges on certain slats, and related investigative and corrective actions if necessary. Since we issued these ADs, we have received reports of slats disbonding on airplanes on which the terminating actions of the existing ADs were completed and also reports of slats disbonding on airplanes outside of the applicability of the existing ADs. This proposed AD would require a determination of the type of trailing edge wedges of the leading edge slats, repetitive inspections on certain trailing edge wedges for areas of skin-to-core disbonding, and corrective actions if necessary. This proposed AD would also provide an optional terminating action for the repetitive inspections. This AD would revise the applicability of the existing ADs to include additional airplanes. We are proposing this AD to prevent delamination of the trailing edge wedge of the leading edge slats, possible loss of pieces of the trailing edge wedge assembly during flight, reduction of the reduced maneuver and stall margins, and consequent reduced controllability of the airplane.

Blade-mounted trailing edge flap control for BVI noise reduction

NASA Technical Reports Server (NTRS)

Hassan, A. A.; Charles, B. D.; Tadghighi, H.; Sankar, L. N.

1992-01-01

Numerical procedures based on the 2-D and 3-D full potential equations and the 2-D Navier-Stokes equations were developed to study the effects of leading and trailing edge flap motions on the aerodynamics of parallel airfoil-vortex interactions and on the aerodynamics and acoustics of the more general self-generated rotor blade vortex interactions (BVI). For subcritical interactions, the 2-D results indicate that the trailing edge flap can be used to alleviate the impulsive loads experienced by the airfoil. For supercritical interactions, the results show the necessity of using a leading edge flap, rather than a trailing edge flap, to alleviate the interaction. Results for various time dependent flap motions and their effect on the predicted temporal sectional loads, differential pressures, and the free vortex trajectories are presented. For the OLS model rotor, contours of a BVI noise metric were used to quantify the effects of the trailing edge flap on the size and directivity of the high/low intensity noise region(s). Average reductions in the BVI noise levels on the order of 5 dB with moderate power penalties on the order of 18 pct. for a four bladed rotor and 58 pct. for a two bladed rotor were obtained.

Audit Technical of Kori Rubber Dam in the River of Keyang District of Ponorogo East Java Province

NASA Astrophysics Data System (ADS)

Murnianto, E.; Suprapto, M.; Ikhsan, C.

2018-03-01

The development of science and technology for the utilization and protection of rivers has embodied various types of river infrastructure. Without proper maintenance, rapid river sediments undergo physical degradation and function. Problems that occur in Kori Rubber Dam, among others, the damage to the body of the rubber dam that is made of rubber, so that the function of flower deflection is not optimal. This happens because of limited operational and maintenance activities (OM). A technical audit is a process of identifying problems, analyzing, and evaluating ones conducted independently, objectively and professionally on the basis of examination, to assess the truth, accuracy, credibility, and reliability of information about a job. In this case an assessment of the Kori Rubber Dam, which is basically a benchmarking activity. Assessment of rubber dam components includes the physical conditions and functions that affect the weir. This research is expected to know the performance of Kori rubber Dam as a recommendation material in the implementation of OM Rubber Dam activities.

The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

NASA Astrophysics Data System (ADS)

Rezaei Abadchi, Majid; Jalali-Arani, Azam

2014-02-01

The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using 60Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >Cdbnd C< double bands decreased. Also Charlesby-Pinner equation was used to evaluate radiation yield.

Analysis of Physical Properties and Mineralogical of Pyrolysis Tires Rubber Ash Compared Natural Sand in Concrete material

NASA Astrophysics Data System (ADS)

Syamir Senin, Mohamad; Shahidan, Shahiron; Syazani Leman, Alif; Izzati Raihan Ramzi Hannan, Nurul

2016-11-01

Waste tires pose significant health and environmental concerns if not recycled or discarded properly. At the same time, natural sand is becoming scarcer and costlier due to its non-availability. Waste tires as fine aggregate can be an economical and sustainable alternative to the natural sand. Recent years, the interest on recycling waste tires into civil engineering applications by the researchers has increased. In this research, the chemical and physical properties of the tires rubber ash and the natural sand have been analysed. The densities of the rubber ash are lower than the natural sand. Rubber ash had finer particle size compared to the natural sand. Almost all chemical in the natural sand had in rubber ash with the additional sulphur trioxide and zinc oxide in the rubber ash, made the rubber ash better than natural sand. Rubber ash seems to be a suitable material to use in concrete as sand replacement.

Practical application of thermoreversibly Cross-linked rubber products

NASA Astrophysics Data System (ADS)

Polgar, L. M.; Picchioni, F.; de Ruiter, E.; van Duin, M.

2017-07-01

Currently, rubber products cannot simply be reprocessed after their product life, due to the irreversible cross-linking methods traditionally applied. The purpose of this work is to investigate how thermoreversible cross-linking of rubbers via Diels Alder chemistry can be used for the development of recyclable rubber products. Unfortunately, the applicability of the thermoreversible EPM-g-furan/BM system appears to be limited to room temperature applications, because of the rapid deterioration of the compression set at elevated temperatures compared to irreversibly cross-linked EPM. However, the use of EPM rubber modified with thiophene or cyclopentadiene moieties may extend the temperature application range and results in rubber products with acceptable properties. Finally, rubber products generally comprise fillers such as silica, carbon black or fibers. In this context, the reinforcing effect of short cut aramid fibers on the material properties of the newly developed thermoreversibly cross-linked EPM rubbers was also studied. The material properties of the resulting products were found to be comparable to those of a fiber reinforced, peroxide cured reference sample.

New type of liquid rubber and compositions based on it.

PubMed

Semikolenov, S V; Nartova, A V; Voronchikhin, V D; Dubkov, K A

2014-11-01

The new method for producing the functionalized polymers and oligomers containing carbonyl C=O groups is developed. The method is based on the noncatalytic oxidation of unsaturated rubbers by nitrous oxide (N2O) at 180-230 °С. The proposed method allows obtaining the new type of functionalized rubbers-liquid unsaturated polyketones with regulated molecular weight and concentration of C=O groups. The influence of the liquid polyketone addition on properties of rubber-based composites is investigated. The study indicates good prospects of using the liquid polyketones for the improvement of properties and operating characteristics of the various types of rubbers and the rubber-cord systems.

Use of rubber crumbs in cement concrete

NASA Astrophysics Data System (ADS)

Longvinenko, A. A.

2018-03-01

Rubber crumb obtained from worn out tires has been increasingly used over the last 15-20 years, especially in manufacture of asphalt and cement concrete mixtures. This review pays principal attention to application of the rubber crumb to cement concrete mixtures. Use of the rubber crumb in cement concrete is not as successful as in asphalt concrete mixtures, due to incompatibility problems linked to chemical composition and a significant difference in rigidity between the rubber crumb and concrete mixture aggregates. Different methods are proposed and studied to mitigate the adverse influence and increase the beneficial effects of the rubber crumb when added to cement concrete.

Adhesion of nitrile rubber to UV-assisted surface chemical modified PET fabric, part II: Interfacial characterization of MDI grafted PET

NASA Astrophysics Data System (ADS)

Razavizadeh, Mahmoud; Jamshidi, Masoud

2016-08-01

Fiber to rubber adhesion is an important subject in rubber industry. It is well known that surface treatment (i.e. physical, mechanical and chemical) is an effective method to improve interfacial bonding of fibers and/or fabrics to rubbers. UV irradiation is an effective method which has been used to increase fabric-rubber interfacial interactions. In this research UV assisted chemical modification of PET fabrics was used to increase PET to nitrile rubber (NBR) adhesion. Nitrile rubber is a perfect selection as fuel and oil resistant rubber. However it has weak bonding to PET fabric. For this purpose PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was grafted on carboxylated PET. The chemical composition of the fabric before and after surface treatment was investigated by X-ray photoelectron spectroscopy (XPS). The sectional morphology of the experimental PET fibers and the interface between rubber compound and PET fabric was studied using scanning electron microscope (SEM). The morphology and structure of the product were analyzed by an energy dispersive X-ray spectrometer (EDX). FTIR-ATR and H NMR analysis were used to assess surface modifications on the PET irradiated fabrics.

Efficacy of tray adhesives for the adhesion of elastomer rubber impression materials to impression modeling plastics for border molding.

PubMed

Nishigawa, G; Sato, T; Suenaga, K; Minagi, S

1998-02-01

Tray adhesive, which is used for the adhesion of elastomer rubber impression materials to a custom resin tray, lowers the retention of the impression materials to the impression modeling plastics, as some ingredients of tray adhesive make the impression modeling plastic soft and tacky. The efficacy of tray adhesive, which is used for the adhesion of elastomer rubber impression materials to a custom resin tray, on the adhesion between elastomer rubber impression material and impression modeling plastic was investigated. Four silicone rubber impression materials (two addition reaction types and two condensation reaction types), two polysulfide rubber impression materials, and one impression modeling plastic were used in this study. Tensile strength between elastomer rubber impression material and impression modeling plastic with or without the application of tray adhesive was evaluated. Although tray adhesives for both addition reaction type and both condensation reaction type of silicone impression materials and one tray adhesive for polysulfide rubber impression material increased the tensile strength between the impression material and impression modeling plastic, one tray adhesive for polysulfide rubber impression material decreased the tensile strength when sufficient drying time was not applied.

Gingival cell proliferation induced by use of a sonic toothbrush with warmed silicone rubber bristles.

PubMed

Tomofuji, Takaaki; Kusano, Hiroki; Azuma, Tetsuji; Ekuni, Daisuke; Yamamoto, Tatsuo; Watanabe, Tatsuo; Kishimoto, Takashi

2004-12-01

Toothbrushing promotes gingival cell proliferation, which may occur as the result of the physical stimulation of the gingiva. The present study evaluated the effects of temperature and silicone rubber bristles of a sonic toothbrush on gingival cell proliferation in dogs. During the 5-week experimental period, one quadrant in each of eight dogs received a different toothbrushing regimen: a manual toothbrush or a sonic toothbrush with 1) nylon, 2) silicone rubber, or 3) warmed silicone rubber bristles. The proliferative activity of gingival cells was evaluated based on expression of proliferating cell nuclear antigen (PCNA). Use of the sonic toothbrushes produced a higher density of PCNA-positive and total fibroblasts than did use of a manual toothbrush. The warm silicone rubber bristles resulted in a higher density of PCNA-positive fibroblasts compared with the cooler silicone rubber bristle. The number of PCNA-positive basal cells in the junctional epithelium also increased following electric toothbrushing with warmed silicone rubber bristles. The sonic toothbrush with silicone rubber bristles induced gingival fibroblast proliferation to a greater degree than a manual toothbrush. Warming the silicone rubber bristles increased their stimulatory effects on the proliferative activity of gingival cells.

Why dentists don't use rubber dam during endodontics and how to promote its usage?

PubMed

Madarati, Ahmad A

2016-02-25

This survey study aimed at investigating the frequency of rubber dam use during root canal treatment, identifying influencing factors for not using it by Saudi general dental practitioners (GDPs) and endodontists. It also aimed at identifying measures that increase rubber dam usage. After obtaining an ethical approval, two pilot studies were conducted on staff members at Taibah University College of Dentistry and a group of GDPs. A final online survey was constructed comprising 17 close-ended questions divided into six categories: demographics, endodontic practice, rubber dam use, alternative isolation methods, reasons for not using rubber dam, and measures and policies that increase its usage. The survey was emailed to 375 GDPs randomly selected from the dental register and all endodontists (n = 53) working in the western province, Saudi Arabia. Data were analyzed using the Chi-square and Linear-by-Linear association tests at p ≤ 0.05. The proportion of endodontists who used rubber dam (84.8 %) was significantly greater than that of GDPs (21.6 %) (p < 0.001). Significantly the highest proportion (40.5 %) did not use rubber dam because of unavailability at working place. Most rubber dam none-users (69.25 %) used a combination of other isolation means. The highest proportion of those who used rubber dam were working in the governmental sector (54.3 %). Among rubber dam users, the greatest proportion graduated from Saudi Arabia (57.8 %) compared to those graduated from Egypt (34.3 %) and Syria (22.4 %). There was a significant correlation between the patterns of rubber dam use during undergraduate training and its usage after graduation (p = 0.001). The highest proportion of participants (48.1 %) reported better undergraduate education as the most important factor that would increase rubber dam use in dental practice. Using of rubber dam was not common in Saudi general dental practice. Dentists must follow the recommended standards of care. Place of work and patterns of using rubber dam during undergraduate study were the most influencing factors. Better undergraduate education was the most important proposed measure to increase its usage. The combination of cotton rolls and saliva high-volume ejector or gauze was the most common alternative to rubber dam isolation.

40 CFR 428.80 - Applicability; description of the wet digestion reclaimed rubber subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... digestion reclaimed rubber subcategory. 428.80 Section 428.80 Protection of Environment ENVIRONMENTAL... CATEGORY Wet Digestion Reclaimed Rubber Subcategory § 428.80 Applicability; description of the wet digestion reclaimed rubber subcategory. The provisions of this subpart are applicable to process waste water...

40 CFR 428.80 - Applicability; description of the wet digestion reclaimed rubber subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... digestion reclaimed rubber subcategory. 428.80 Section 428.80 Protection of Environment ENVIRONMENTAL... Wet Digestion Reclaimed Rubber Subcategory § 428.80 Applicability; description of the wet digestion... discharges resulting from the production of reclaimed rubber by use of the wet digestion process. ...

40 CFR 428.80 - Applicability; description of the wet digestion reclaimed rubber subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... digestion reclaimed rubber subcategory. 428.80 Section 428.80 Protection of Environment ENVIRONMENTAL... CATEGORY Wet Digestion Reclaimed Rubber Subcategory § 428.80 Applicability; description of the wet digestion reclaimed rubber subcategory. The provisions of this subpart are applicable to process waste water...

40 CFR 428.80 - Applicability; description of the wet digestion reclaimed rubber subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... digestion reclaimed rubber subcategory. 428.80 Section 428.80 Protection of Environment ENVIRONMENTAL... Wet Digestion Reclaimed Rubber Subcategory § 428.80 Applicability; description of the wet digestion... discharges resulting from the production of reclaimed rubber by use of the wet digestion process. ...

40 CFR 428.80 - Applicability; description of the wet digestion reclaimed rubber subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... digestion reclaimed rubber subcategory. 428.80 Section 428.80 Protection of Environment ENVIRONMENTAL... CATEGORY Wet Digestion Reclaimed Rubber Subcategory § 428.80 Applicability; description of the wet digestion reclaimed rubber subcategory. The provisions of this subpart are applicable to process waste water...

Transcriptome and gene expression analysis in cold-acclimated guayule (Parthenium argentatum)rubber-producing tissue

USDA-ARS?s Scientific Manuscript database

Natural rubber biosynthesis in guayule (Parthenium argentatum) is associated with moderately cold night temperatures. To begin to dissect the molecular events triggered by cold temperatures that govern rubber synthesis induction in guayule, the transcriptome of bark tissue, where rubber is produced...

Evaluation of the use of rubber-tire rollers on asphalt concrete.

DOT National Transportation Integrated Search

1989-01-01

The addition of a rubber-tire roller was required on two projects on maintenance schedules and on two construction projects in 1988. The rubber-tire roller was used as an addition to the conventional rollers on one-half of each project. The rubber-ti...

Evaluation of crumb rubber in hot mix asphalt.

DOT National Transportation Integrated Search

2004-07-01

An asphalt-rubber hot mix asphalt (AR-HMA) design was created using a Superpave 12.5mm gradation and a #30 (-) mesh : crumb rubber at 20% total weight of the asphalt binder. At this point in time, asphalt rubber has only been used with HMA : that con...

27 CFR 21.125 - Rubber hydrocarbon solvent.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative. (b...

27 CFR 21.125 - Rubber hydrocarbon solvent.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative. (b...

A sustainability review of domestic rubber from the guayule plant

USDA-ARS?s Scientific Manuscript database

Guayule (Parthenium argentatum Gray) is an arid-adapted, low-input perennial shrub native to Mexico and southern Texas that has received considerable attention as an alternative source of natural rubber. It has potential to replace the most common types of rubbers, including synthetic rubber derived...

Analysis of a Compressible Fluid Soft Recoil (CFSR) Concept Applied to a 155 MM Howitzer

DTIC Science & Technology

1979-03-01

Nitrile or Buna-N ( NBR ) rubber with ’ backup rings of nylotron. HITRILE NVLOTRON Piston seals An unresolved problem is that the coefficient of...fluid at atmospheric pressure Poisson’s ratio for Nitrile rubber dynamic coefficient of friction for rubber mass of recoiling parts weight of...Greene, tweed 5 Co. Palmetto catalog.) 43 [i^ - 0.50 = coefficient of friction (An approximate figure for rubber supplied by RIA Rubber

Toxicity of Pyrolysis Gases from Elastomers

NASA Technical Reports Server (NTRS)

Hilado, Carlos J.; Kosola, Kay L.; Solis, Alida N.; Kourtides, Demetrius A.; Parker, John A.

1977-01-01

The toxicity of the pyrolysis gases from six elastomers was investigated. The elastomers were polyisoprene (natural rubber), styrene-butadiene rubber (SBR), ethylene propylene diene terpolymer (EPDM), acrylonitrile rubber, chlorosulfonated polyethylene rubber, and polychloroprene. The rising temperature and fixed temperature programs produced exactly the same rank order of materials based on time to death. Acryltonitrile rubber exhibited the greatest toxicity under these test conditions; carbon monoxide was not found in sufficient concentrations to be the primary cause of death.

Effects of preparation process on performance of rubber modified asphalt

NASA Astrophysics Data System (ADS)

Liu, Hanbing; Luo, Guobao; Wang, Xianqiang; Jiao, Yubo

2015-06-01

The rational utilization of waste rubber tire is essential for the environmental protection. Utilizing rubber particles to modify asphalt can not only improve asphalt performance, but also help the recycling of waste materials. Considering the effect of different preparation process parameters on the performance of rubber modified asphalt, this paper analyzes the effects of the shear temperature, shear time and shear rate on the performance of rubber modified asphalt, and provided a reference for its preparation.

Correlation Of Ortho-Positronium Intensity With Doppler Broadening For Rubber Above And Below The Glass Transition Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Towry, Amanda; Quarles, C. A.

Previous research has demonstrated a correlation between the Doppler broadening S parameter and the intensity of the ortho-positronium lifetime component in polymers that depends on the composition of the polymer. On the other hand, rubber polymers do not show this correlation and behave more like liquids for which the S parameter is essentially independent of the ortho-positronium intensity. The bubble model has been suggested as an explanation of the lack of correlation in analogy with liquids, but the bubble model applied to rubber is controversial. There are two important differences between the rubber and the polymers samples: first, the rubbermore » samples at room temperature were all above the glass transition temperature (T{sub G}). Second, the rubber samples all contained sulfur and were vulcanized. These differences were investigated by first measuring the S parameter for six rubber samples below T{sub G} where the bubble model would not be expected to work. Second, raw rubber samples that did not contain any sulfur and were unvulcanized were studied at room temperature. The results show that the lack of correlation between the S parameter and the ortho-positronium intensity previously observed for vulcanized rubber is due to the inhibition of positronium formation by the sulfur in the vulcanized rubber samples rather than to the rubber being above T{sub G}.« less

Attention in selective mutism--an exploratory case-control study.

PubMed

Oerbeck, Beate; Kristensen, Hanne

2008-01-01

The aim of the study was to explore the association between selective mutism (SM) and attention. In SM social anxiety seems central but language impairment and motor problems are also reported. Attention problems have been described in parental behavioral ratings, while neuropsychological studies are lacking. A neuropsychological test (the Trail Making Test) and parental ratings of attention- and anxiety problems were administered to a clinical sample of 23 children with SM (aged 7-16 years, 12 boys and 11 girls) and 46 non-referred matched controls. The SM group differed from controls on the Trail Making Test, but the group difference disappeared, when controlling for motor function and IQ. Parental ratings of attention problems were not significantly associated with the neuropsychological attention measure. Neuropsychological studies of attention controlled for IQ and motor function are needed as well as tests that measure different aspects of attention.

Arabidopsis AtPAP1 transcription factor induces anthocyanin production in transgenic Taraxacum brevicorniculatum.

PubMed

Qiu, Jian; Sun, Shuquan; Luo, Shiqiao; Zhang, Jichuan; Xiao, Xianzhou; Zhang, Liqun; Wang, Feng; Liu, Shizhong

2014-04-01

This study developed a new purple coloured Taraxacum brevicorniculatum plant through genetic transformation using the Arabidopsis AtPAP1 gene, which overproduced anthocyanins in its vegetative tissues. Rubber-producing Taraxacum plants synthesise high-quality natural rubber (NR) in their roots and so are a promising alternative global source of this raw material. A major factor in its commercialization is the need for multipurpose exploitation of the whole plant. To add value to the aerial tissues, red/purple plants of the rubber-producing Taraxacum brevicorniculatum species were developed through heterologous expression of the production of anthocyanin pigment 1 (AtPAP1) transcription factor from Arabidopsis thaliana. The vegetative tissue of the transgenic plants showed an average of a 48-fold increase in total anthocyanin content over control levels, but with the exception of pigmentation, the transgenic plants were phenotypically comparable to controls and displayed similar growth vigor. Southern blot analysis confirmed that the AtPAP1 gene had been integrated into the genome of the high anthocyanin Taraxacum plants. The AtPAP1 expression levels were estimated by quantitative real-time PCR and were highly correlated with the levels of total anthocyanins in five independent transgenic lines. High levels of three cyanidin glycosides found in the purple plants were characterized by high performance liquid chromatography-mass spectrum analysis. The presence of NR was verified by NMR and infrared spectroscopy, and confirmed that NR biosynthesis had not been affected in the transgenic Taraxacum lines. In addition, other major phenylpropanoid products such as chlorogenic acid and quercetin glycosides were also enhanced in the transgenic Taraxacum. The red/purple transgenic Taraxacum lines described in this study would increase the future application of the species as a rubber-producing crop due to its additional health benefits.

The Moving Rubber Hand Illusion Reveals that Explicit Sense of Agency for Tapping Movements Is Preserved in Functional Movement Disorders.

PubMed

Marotta, Angela; Bombieri, Federica; Zampini, Massimiliano; Schena, Federico; Dallocchio, Carlo; Fiorio, Mirta; Tinazzi, Michele

2017-01-01

Functional movement disorders (FMD) are characterized by motor symptoms (e.g., tremor, gait disorder, and dystonia) that are not compatible with movement abnormalities related to a known organic cause. One key clinical feature of FMD is that motor symptoms are similar to voluntary movements but are subjectively experienced as involuntary by patients. This gap might be related to abnormal self-recognition of bodily action, which involves two main components: sense of agency and sense of body ownership. The aim of this study was to systematically investigate whether this function is altered in FMD, specifically focusing on the subjective feeling of agency, body ownership, and their interaction during normal voluntary movements. Patients with FMD ( n = 21) and healthy controls ( n = 21) underwent the moving Rubber Hand Illusion (mRHI), in which passive and active movements can differentially elicit agency, ownership or both. Explicit measures of agency and ownership were obtained via a questionnaire. Patients and controls showed a similar pattern of response: when the rubber hand was in a plausible posture, active movements elicited strong agency and ownership; implausible posture of the rubber hand abolished ownership but not agency; passive movements suppressed agency but not ownership. These findings suggest that explicit sense of agency and body ownership are preserved in FMD. The latter finding is shared by a previous study in FMD using a static version of the RHI, whereas the former appears to contrast with studies demonstrating altered implicit measures of agency (e.g., sensory attenuation). Our study extends previous findings by suggesting that in FMD: (i) the sense of body ownership is retained also when interacting with the motor system; (ii) the subjective experience of agency for voluntary tapping movements, as measured by means of mRHI, is preserved.

40 CFR 428.95 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mechanical Reclaimed Rubber Subcategory § 428.95 Standards of performance for new sources. (a) The following standards of performance establish the quantity or quality of pollutants or pollutant properties, controlled... or quality of pollutants or pollutant properties, controlled by this section and attributable to pan...

Quantification of trans-1,4-polyisoprene in Eucommia ulmoides by fourier transform infrared spectroscopy and pyrolysis-gas chromatography/mass spectrometry.

PubMed

Takeno, Shinya; Bamba, Takeshi; Nakazawa, Yoshihisa; Fukusaki, Eiichiro; Okazawa, Atsushi; Kobayashi, Akio

2008-04-01

Commercial development of trans-1,4-polyisoprene from Eucommia ulmoides Oliver (EU-rubber) requires specific knowledge on selection of high-rubber-content lines and establishment of agronomic cultivation methods for achieving maximum EU-rubber yield. The development can be facilitated by high-throughput and highly sensitive analytical techniques for EU-rubber extraction and quantification. In this paper, we described an efficient EU-rubber extraction method, and validated that the accuracy was equivalent to that of the conventional Soxhlet extraction method. We also described a highly sensitive quantification method for EU-rubber by Fourier transform infrared spectroscopy (FT-IR) and pyrolysis-gas chromatography/mass spectrometry (PyGC/MS). We successfully applied the extraction/quantification method for study of seasonal changes in EU-rubber content and molecular weight distribution.

Lipid Nanoparticles Decorated with TNF-Related Aptosis-Inducing Ligand (TRAIL) Are More Cytotoxic than Soluble Recombinant TRAIL in Sarcoma.

PubMed

Gallego-Lleyda, Ana; De Miguel, Diego; Anel, Alberto; Martinez-Lostao, Luis

2018-05-13

Sarcomas are rare and heterogeneous cancers classically associated with a poor outcome. Sarcomas are 1% of the cancer but recent estimations indicate that sarcomas account for 2% of the estimated cancer-related deaths. Traditional treatment with surgery, radiotherapy, and chemotherapy has improved the outcome for some types of sarcomas. However, novel therapeutic strategies to treat sarcomas are necessary. TNF-related apoptosis-inducing ligand (TRAIL) is a death ligand initially described as capable of inducing apoptosis on tumor cell while sparing normal cells. Only few clinical trials have used TRAIL-based treatments in sarcoma, but they show only low or moderate efficacy of TRAIL. Consequently, novel TRAIL formulations with an improved TRAIL bioactivity are necessary. Our group has developed a novel TRAIL formulation based on tethering this death ligand on a lipid nanoparticle surface (LUV-TRAIL) resembling the physiological secretion of TRAIL as a trasmembrane protein inserted into the membrane of exosomes. We have already demonstrated that LUV-TRAIL shows an improved cytotoxic activity when compared to soluble recombinant TRAIL both in hematological malignancies and epithelial-derived cancers. In the present study, we have tested LUV-TRAIL in several human sarcoma tumor cell lines with different sensitivity to soluble recombinant TRAIL, finding that LUV-TRAIL was more efficient than soluble recombinant TRAIL. Moreover, combined treatment of LUV-TRAIL with distinct drugs proved to be especially effective, sensitizing even more resistant cell lines to TRAIL.

Recycled tire crumb rubber anodes for sustainable power production in microbial fuel cells

NASA Astrophysics Data System (ADS)

Wang, Heming; Davidson, Matthew; Zuo, Yi; Ren, Zhiyong

One of the greatest challenges facing microbial fuel cells (MFCs) in large scale applications is the high cost of electrode material. We demonstrate here that recycled tire crumb rubber coated with graphite paint can be used instead of fine carbon materials as the MFC anode. The tire particles showed satisfactory conductivity after 2-4 layers of coating. The specific surface area of the coated rubber was over an order of magnitude greater than similar sized graphite granules. Power production in single chamber tire-anode air-cathode MFCs reached a maximum power density of 421 mW m -2, with a coulombic efficiency (CE) of 25.1%. The control graphite granule MFC achieved higher power density (528 mW m -2) but lower CE (15.6%). The light weight of tire particle could reduce clogging and maintenance cost but posts challenges in conductive connection. The use of recycled material as the MFC anodes brings a new perspective to MFC design and application and carries significant economic and environmental benefit potentials.

75 FR 29466 - Airworthiness Directives; Gulfstream Aerospace LP (Type Certificate Previously Held by Israel...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-26

... baggage compartment rubber seals, and replacing the baggage compartment rubber seals manufactured by Gumiyan with seals manufactured by Rubbercraft. Since the proposed AD was issued, we have received new... manufacturer of the baggage compartment rubber seals, and replacing the baggage compartment rubber seals...

40 CFR 428.90 - Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., dry digestion, and mechanical reclaimed rubber subcategory. 428.90 Section 428.90 Protection of... MANUFACTURING POINT SOURCE CATEGORY Pan, Dry Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.90 Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory. The...

40 CFR 428.90 - Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., dry digestion, and mechanical reclaimed rubber subcategory. 428.90 Section 428.90 Protection of... MANUFACTURING POINT SOURCE CATEGORY Pan, Dry Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.90 Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory. The...

40 CFR 428.90 - Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., dry digestion, and mechanical reclaimed rubber subcategory. 428.90 Section 428.90 Protection of... POINT SOURCE CATEGORY Pan, Dry Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.90 Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory. The...

40 CFR 428.90 - Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., dry digestion, and mechanical reclaimed rubber subcategory. 428.90 Section 428.90 Protection of... MANUFACTURING POINT SOURCE CATEGORY Pan, Dry Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.90 Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory. The...

40 CFR 428.90 - Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., dry digestion, and mechanical reclaimed rubber subcategory. 428.90 Section 428.90 Protection of... POINT SOURCE CATEGORY Pan, Dry Digestion, and Mechanical Reclaimed Rubber Subcategory § 428.90 Applicability; description of the pan, dry digestion, and mechanical reclaimed rubber subcategory. The...

Modified Silicone-Rubber Tooling For Molding Composite Parts

NASA Technical Reports Server (NTRS)

Baucom, Robert M.; Snoha, John J.; Weiser, Erik S.

1995-01-01

Reduced-thermal-expansion, reduced-bulk-modulus silicone rubber for use in mold tooling made by incorporating silica powder into silicone rubber. Pressure exerted by thermal expansion reduced even further by allowing air bubbles to remain in silicone rubber instead of deaerating it. Bubbles reduce bulk modulus of material.

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded, extruded, and...

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2014 CFR

2014-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... (CONTINUED) RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded...

40 CFR 428.60 - Applicability; description of the medium-sized general molded, extruded, and fabricated rubber...

Code of Federal Regulations, 2013 CFR

2013-07-01

... medium-sized general molded, extruded, and fabricated rubber plants subcategory. 428.60 Section 428.60... (CONTINUED) RUBBER MANUFACTURING POINT SOURCE CATEGORY Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants Subcategory § 428.60 Applicability; description of the medium-sized general molded...

40 CFR 63.494 - Back-end process provisions-residual organic HAP and emission limitations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... producing butyl rubber, epichlorohydrin elastomer, neoprene, and nitrile butadiene rubber shall not exceed... processes at affected sources producing butyl rubber, epichlorohydrin elastomer, neoprene, and nitrile... submitted in accordance with § 63.499(f)(1). (i) For butyl rubber, the organic HAP emission limitation shall...

40 CFR 62.14102 - Affected facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... plastics/rubber recycling unit (as defined in 40 CFR 60.51b) are not subject to this subpart if the owner or operator of the plastics/rubber recycling unit keeps records of the weight of plastics, rubber... chemical plants or petroleum refineries that use feestocks produced by plastics/rubber recycling units are...

40 CFR 62.14102 - Affected facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... plastics/rubber recycling unit (as defined in 40 CFR 60.51b) are not subject to this subpart if the owner or operator of the plastics/rubber recycling unit keeps records of the weight of plastics, rubber... chemical plants or petroleum refineries that use feestocks produced by plastics/rubber recycling units are...

40 CFR 62.14102 - Affected facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... plastics/rubber recycling unit (as defined in 40 CFR 60.51b) are not subject to this subpart if the owner or operator of the plastics/rubber recycling unit keeps records of the weight of plastics, rubber... chemical plants or petroleum refineries that use feestocks produced by plastics/rubber recycling units are...