9. VIEW OF THE TRASH RAKES, TRASH RAKE GATELIFTING MECHANISM, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. VIEW OF THE TRASH RAKES, TRASH RAKE GATE-LIFTING MECHANISM, AND SHED ROOF (REMOVED AUTUMN OF 1996), WITH TRASH LOG LIFTING MECHANISM IN FOREGROUND, LOOKING WEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

The evaluation of a rake method to quantify submersed vegetation in the Upper Mississippi River

USGS Publications Warehouse

Yin, Yao; Kreiling, Rebecca M.

2011-01-01

A long-handled, double-headed garden rake was used to collect submersed aquatic vegetation (SAV) and compared to in-boat visual inspection to record species presence at 67 individual sites. Six rake subsamples were taken at each site and a rake density rating was given to each species collected in the subsamples. Presence at the site, frequency of occurrence in the six rake samples, and additive density rating (the sum of the six rake density ratings) were quantified for each species at each site. The validity of the indices was tested against biomass data collected by clipping all remaining vegetation from the 67 sites. In the turbid water of the Mississippi River, visual inspection of SAV from boats was ineffective with only 27% of the species detected, while raking retrieved on average 70% of the total number of submersed species in the 67 sites. Presence of species at individual sites was correlated with biomass from Stuckenia pectinata, while frequency of occurrence and additive density rating were correlated with biomass for species with greater than 21 g of total biomass from all sites. The efficiency of the rake to collect biomass varied among species; only 18% of total biomass was captured via raking the site six times. Additive density rating as an index of abundance can be used to detect temporal changes in the same water body; however, cross-species comparison is not encouraged unless the efficiency of the rake has been determined for each species being compared.

Power optimization of digital baseband WCDMA receiver components on algorithmic and architectural level

NASA Astrophysics Data System (ADS)

Schämann, M.; Bücker, M.; Hessel, S.; Langmann, U.

2008-05-01

High data rates combined with high mobility represent a challenge for the design of cellular devices. Advanced algorithms are required which result in higher complexity, more chip area and increased power consumption. However, this contrasts to the limited power supply of mobile devices. This presentation discusses the application of an HSDPA receiver which has been optimized regarding power consumption with the focus on the algorithmic and architectural level. On algorithmic level the Rake combiner, Prefilter-Rake equalizer and MMSE equalizer are compared regarding their BER performance. Both equalizer approaches provide a significant increase of performance for high data rates compared to the Rake combiner which is commonly used for lower data rates. For both equalizer approaches several adaptive algorithms are available which differ in complexity and convergence properties. To identify the algorithm which achieves the required performance with the lowest power consumption the algorithms have been investigated using SystemC models regarding their performance and arithmetic complexity. Additionally, for the Prefilter Rake equalizer the power estimations of a modified Griffith (LMS) and a Levinson (RLS) algorithm have been compared with the tool ORINOCO supplied by ChipVision. The accuracy of this tool has been verified with a scalable architecture of the UMTS channel estimation described both in SystemC and VHDL targeting a 130 nm CMOS standard cell library. An architecture combining all three approaches combined with an adaptive control unit is presented. The control unit monitors the current condition of the propagation channel and adjusts parameters for the receiver like filter size and oversampling ratio to minimize the power consumption while maintaining the required performance. The optimization strategies result in a reduction of the number of arithmetic operations up to 70% for single components which leads to an estimated power reduction of up to 40% while the BER performance is not affected. This work utilizes SystemC and ORINOCO for the first estimation of power consumption in an early step of the design flow. Thereby algorithms can be compared in different operating modes including the effects of control units. Here an algorithm having higher peak complexity and power consumption but providing more flexibility showed less consumption for normal operating modes compared to the algorithm which is optimized for peak performance.

Does raking basal duff affect tree growth rates or mortality?

Treesearch

Erin Noonan-Wright; Sharon M. Hood; Danny R. Cluck

2010-01-01

Mortality and reduced growth rates due to raking accumulated basal duff were evaluated for old, large-diameter ponderosa and Jeffrey pine trees on the Lassen National Forest, California. No fire treatments were included to isolate the effect of raking from fire. Trees were monitored annually for 5 years after the raking treatment for mortality and then cored to measure...

Semiempirical method of determining flow coefficients for pitot rake mass flow rate measurements

NASA Technical Reports Server (NTRS)

Trefny, C. J.

1985-01-01

Flow coefficients applicable to area-weighted pitot rake mass flow rate measurements are presented for fully developed, turbulent flow in an annulus. A turbulent velocity profile is generated semiempirically for a given annulus hub-to-tip radius ratio and integrated numerically to determine the ideal mass flow rate. The calculated velocities at each probe location are then summed, and the flow rate as indicated by the rake is obtained. The flow coefficient to be used with the particular rake geometry is subsequently obtained by dividing the ideal flow rate by the rake-indicated flow rate. Flow coefficients ranged from 0.903 for one probe placed at a radius dividing two equal areas to 0.984 for a 10-probe area-weighted rake. Flow coefficients were not a strong function of annulus hub-to-tip radius ratio for rakes with three or more probes. The semiempirical method used to generate the turbulent velocity profiles is described in detail.

Raking it in: the impact of enculturation on chimpanzee tool use.

PubMed

Furlong, E E; Boose, K J; Boysen, S T

2008-01-01

Recent evidence for different tool kits, proposed to be based upon culture-like transmission, have been observed across different chimpanzee communities across Western Africa. In light of these findings, the reported failures by seven captive juvenile chimpanzees tested with 27 tool use tasks (Povinelli 2000) seem enigmatic. Here we report successful performance by a group of nine captive, enculturated chimpanzees, and limited success by a group of six semi-enculturated chimpanzees, on two of the Povinelli tasks, the Flimsy Tool task, and the Hybrid Tool task. All chimpanzees were presented with a rake with a flimsy head and a second rake with a rigid head, either of which could be used to attempt to retrieve a food reward that was out of reach. The rigid rake was constructed such that it had the necessary functional features to permit successful retrieval, while the flimsy rake did not. Both chimpanzee groups in the present experiment selected the functional rigid tool correctly to use during the Flimsy Tool task. All animals were then presented with two "hybrid rakes" A and B, with one half of each rake head constructed from flimsy, non-functional fabric, and the other half of the head was made of wood. Food rewards were placed in front of the rigid side of Rake A and the flimsy side of Rake B. To be successful, the chimps needed to choose the rake that had the reward in front of the rigid side of the rake head. The fully enculturated animals were successful in selecting the functional rake, while the semi-enculturated subjects chose randomly between the two hybrid tools. Compared with findings from Povinelli, whose non-enculturated animals failed both tasks, our results demonstrate that chimpanzees reared under conditions of semi-enculturation could learn to discriminate correctly the necessary tool through trial-and-error during the Flimsy Tool task, but were unable to recognize the functional relationship necessary for retrieving the reward with the "hybrid" rake. In contrast, the enculturated chimpanzees were correct in their choices during both the Flimsy Tool and the Hybrid Tool tasks. These results provide the first empirical evidence for the differential effects of enculturation on subsequent tool use capacities in captive chimpanzees.

Pinestraw raking, fertilization and poultry litter amendment effects on soil physical properties for a mid-rotation loblolly pine plantation

Treesearch

William B. Patterson; Michael A. Blazier; Steven L. Holtard

2010-01-01

Frequent pinestraw raking and removal in pine plantations has led to concerns about nutrient removal from the stand. While soil chemistry of raked stands has been studied, little attention has been placed on potential compaction from raking operations. Four treatments were applied to a 16-year-old loblolly pine plantation at the Louisiana State University AgCenter...

Design and flight testing of a nullable compressor face rake

NASA Technical Reports Server (NTRS)

Holzman, J. K.; Payne, G. A.

1973-01-01

A compressor face rake with an internal valve arrangement to permit nulling was designed, constructed, and tested in the laboratory and in flight at the NASA Flight Research Center. When actuated by the pilot in flight, the nullable rake allowed the transducer zero shifts to be determined and then subsequently removed during data reduction. Design details, the fabrication technique, the principle of operation, brief descriptions of associated digital zero-correction programs and the qualification tests, and test results are included. Sample flight data show that the zero shifts were large and unpredictable but could be measured in flight with the rake. The rake functioned reliably and as expected during 25 hours of operation under flight environmental conditions and temperatures from 230 K (-46 F) to greater than 430 K (314 F). The rake was nulled approximately 1000 times. The in-flight zero-shift measurement technique, as well as the rake design, was successful and should be useful in future applications, particularly where accurate measurements of both steady-state and dynamic pressures are required under adverse environmental conditions.

Dual Rotating Rake Measurements of Higher-Order Duct Modes: Validation Using Experimental and Numerical Data

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Hixon, Duane R.; Sutliff, Daniel L.

2018-01-01

A rotating rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode coefficient amplitudes and phases were quantified. Early studies using this system found that mode power levels computed from rotating rake measured data would agree with the far-field power levels. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection and previous studies suggested conditions could exist where significant reflections could occur. This paper shows that mounting a second rake to the rotating system, with an offset in both the axial and the azimuthal directions, measures the data necessary to determine the modes propagating in both directions within a duct. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode coefficients at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode coefficients for the modes propagating in both directions within the duct while accounting for the presence of evanescent modes. The validation of the dual-rotating-rake measurements was conducted using data from a combination of experiments and numerical calculations to compute reflection coefficients and other mode coefficient ratios. Compared to results from analytical and numerical computations, the results from dual-rotating-rake measured data followed the expected trends when frequency, mode number, and duct termination geometry were changed.

The effects of raking on sugar pine mortality following prescribed fire in Sequoia and Kings Canyon National Parks, California, USA

USGS Publications Warehouse

Nesmith, Jonathan C. B.; O'Hara, Kevin L.; van Mantgem, Phillip J.; de Valpine, Perry

2010-01-01

Prescribed fire is an important tool for fuel reduction, the control of competing vegetation, and forest restoration. The accumulated fuels associated with historical fire exclusion can cause undesirably high tree mortality rates following prescribed fires and wildfires. This is especially true for sugar pine (Pinus lambertiana Douglas), which is already negatively affected by the introduced pathogen white pine blister rust (Cronartium ribicola J.C. Fisch. ex Rabenh). We tested the efficacy of raking away fuels around the base of sugar pine to reduce mortality following prescribed fire in Sequoia and Kings Canyon national parks, California, USA. This study was conducted in three prescribed fires and included 457 trees, half of which had the fuels around their bases raked away to mineral soil to 0.5 m away from the stem. Fire effects were assessed and tree mortality was recorded for three years after prescribed fires. Overall, raking had no detectable effect on mortality: raked trees averaged 30% mortality compared to 36% for unraked trees. There was a significant effect, however, between the interaction of raking and average pre-treatment forest floor fuel depth: the predicted probability of survival of a 50 cm dbh tree was 0.94 vs. 0.96 when average pre-treatment fuel depth was 0 cm for a raked and unraked tree, respectively. When average pre-treatment forest floor fuel depth was 30 cm, the predicted probability of survival for a raked 50 cm dbh tree was 0.60 compared to only 0.07 for an unraked tree. Raking did not affect mortality when fire intensity, measured as percent crown volume scorched, was very low (0% scorch) or very high (>80% scorch), but the raking treatment significantly increased the proportion of trees that survived by 9.6% for trees that burned under moderate fire intensity (1% to 80% scorch). Raking significantly reduced the likelihood of bole charring and bark beetle activity three years post fire. Fuel depth and anticipated fire intensity need to be accounted for to maximize the effectiveness of the treatments. Raking is an important management option to reduce tree mortality from prescribed fire, but is most effective under specific fuel and burning conditions.

Flow Visualization on a Small Scale.

DTIC Science & Technology

1988-03-01

1150 22.43 26 A good tunnel must have very uniform flow across the test section. The uniformity was checked using a seven tube pitot static rake ...calibration. il Figure 7. The Pitot Static Rake 27 To map the entire 15 x 24 inch cross section 84 individual readings and 12 rake locations were required... rake readings was taken, the micromanometer was reattached to the permanent pitot static probe to ensure calibration of the tunnel to .02 inches of

Further Development of Rotating Rake Mode Measurement Data Analysis

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Hixon, Ray; Sutliff, Daniel L.

2013-01-01

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode amplitudes and phases were quantified. For low-speed fans within axisymmetric ducts, mode power levels computed from rotating rake measured data would agree with the far-field power levels on a tone by tone basis. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection at the exit and previous studies suggested conditions could exist where significant reflections could occur. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. The fit equations were also modified to allow evanescent mode amplitudes to be computed. This extension of the rotating rake data analysis technique was tested using simulated data, numerical code produced data, and preliminary in-duct measured data.

Analysis of Dual Rotating Rake Data from the NASA Glenn Advanced Noise Control Fan Duct with Artificial Sources

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Sutliff, Daniel L.

2014-01-01

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. Initially, the mode amplitudes and phases were quantified from a single rake measurement at one axial location. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was then extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. Validation experiments have been conducted using artificial acoustic sources. Results are shown for the measurement of the standing waves in the duct from sound generated by one and two acoustic sources that are separated into the component modes propagating in both directions within the duct. Measured reflection coefficients from the open end of the duct are compared to analytical predictions.

Ground Impingement of a Fan Jet Exhaust Plume

DTIC Science & Technology

1978-05-01

ground plane to avoid a possible interaction between the ground-deflected exhaust and the fan j .t engine inlet. Two pitot pressure rakes , shown on the...Pressure signals from the two rakes (total of 18 pitot tubes) were read sequentially with a Scannivalve system, time-averaged, and displayed on a pen...taken from the inner anid outer rakes with the ground plane normal to the flow at h/d f 2. Pitot pressures from each rake were normalized by the

Multipurpose Rotating Rake Arrays for Integrated Inlet and Fan Stage Performance Measurement

NASA Technical Reports Server (NTRS)

Wolter, John D.

2017-01-01

Low-pressure-ratio fan stage performance measurement requires precise measurement of conditions upstream and downstream of the fan stage. This presentation will discuss the rotating rake arrays used for the recent Boundary Layer Ingesting Inlet-Distortion-Tolerant Fan experiment in the NASA Glenn 8 by 6 foot wind tunnel. To achieve precise measurements, simulations of the rake sampling from pre-test CFD (Computerized Fluid Dynamics) solutions were used to optimize the number and locations of rake instruments.

Rotating Rake Turbofan Duct Mode Measurement System

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2005-01-01

An experimental measurement system was developed and implemented by the NASA Glenn Research Center in the 1990s to measure turbofan duct acoustic modes. The system is a continuously rotating radial microphone rake that is inserted into the duct. This Rotating Rake provides a complete map of the acoustic duct modes present in a ducted fan and has been used on a variety of test articles: from a low-speed, concept test rig, to a full-scale production turbofan engine. The Rotating Rake has been critical in developing and evaluating a number of noise reduction concepts as well as providing experimental databases for verification of several aero-acoustic codes. More detailed derivation of the unique Rotating Rake equations are presented in the appendix.

Design and development of an F/A-18 inlet distortion rake: A cost and time saving solution

NASA Technical Reports Server (NTRS)

Yuhas, Andrew J.; Ray, Ronald J.; Burley, Richard R.; Steenken, William G.; Lechtenberg, Leon; Thornton, Don

1995-01-01

An innovative inlet total pressure distortion measurement rake has been designed and developed for the F/A-18 A/B/C/D aircraft inlet. The design was conceived by NASA and General Electric Aircraft Engines personnel. This rake has been flight qualified and flown in the F/A-18 High Alpha Research Vehicle at NASA Dryden Flight Research Center, Edwards, California. The eight-legged, one-piece, wagon wheel design of the rake was developed at a reduced cost and offered reduced installation time compared to traditional designs. The rake features 40 dual-measurement ports for low- and high-frequency pressure measurements with the high-frequency transducer mounted at the port. This high-frequency transducer offers direct absolute pressure measurements from low to high frequencies of interest, thereby allowing the rake to be used during highly dynamic aircraft maneuvers. Outstanding structural characteristics are inherent to the design through its construction and use of lightweight materials.

Thrust Vectoring for Advanced Fighter Aircraft - High Angle of Attack Intake Investigations -

DTIC Science & Technology

2001-06-01

these losses. plane) a rake for the measurement of swirl and pressure recovery has been used. The five-hole probes and the pitot Whereas the total...true for the two be recognized in fig. 4,3.1. There exist 8 rake arms with 7 pitot intake parameters mean swirl and dynamic distortion. In order probes...recognized that at the low intake mass this rake is measured with the help of 16 rake arms with 5 pitot flowT the pressure recovery up to an angle of

Biomechanics of a convergently derived prey-processing mechanism in fishes: evidence from comparative tongue bite apparatus morphology and raking kinematics.

PubMed

Konow, Nicolai; Sanford, Christopher P J

2008-11-01

A tongue-bite apparatus (TBA) governs raking behaviors in two major and unrelated teleost lineages, the osteoglossomorph and salmoniform fishes. We present data on comparative morphology and kinematics from two representative species, the rainbow trout (Oncorhynchus mykiss) and the Australian arowana (Scleropages jardinii), which suggest that both the TBA and raking are convergently derived in these lineages. Similar TBA morphologies were present, except for differences in TBA dentition and shape of the novel cleithrobranchial ligament (CBL), which is arc-shaped in O. mykiss and straight in S. jardinii. Eight kinematic variables were used to quantify motion magnitude and maximum-timing in the kinematic input mechanisms of the TBA. Five variables differed inter-specifically (pectoral girdle retraction magnitude and timing, cranial and hyoid elevation and gape-distance timing), yet an incomplete taxon separation across multivariate kinematic space demonstrated an overall similarity in raking behavior. An outgroup analysis using bowfin (Amia calva) and pickerel (Esox americanus) to compare kinematics of raking with chewing and prey-capture provided robust quantitative evidence of raking being a convergently derived behavior. Support was also found for the notion that raking more likely evolved from the strike, a functionally distinct behavior, than from chewing, an alternative prey-processing behavior. Based on raking kinematic and muscle-activity data, we propose biomechanical models of the three input mechanisms that govern kinematics of the basihyal output mechanism during the raking power stroke: (1) cranial elevation protracts the upper TBA jaw from the lower (basihyal) TBA jaw; (2) basihyal retraction is caused directly by contraction of the sternohyoideus (SH); (3) hypaxial shortening, relayed via the pectoral girdle and SH-CBL complex, is an indirect basihyal retraction mechanism modeled as a four-bar linkage. These models will aid future analyses mapping structural and functional traits to the evolution of behaviors.

Longleaf pine site response to repeated fertilization and forest floor removal by raking and prescribed burning

Treesearch

Kim Ludovici; Robert Eaton; Stanley Zarnoch

2018-01-01

Removal of forest floor litter by pine needle raking and prescribed burning is a common practice in longleaf pine (Pinus palustris Mill.) stands on Coastal Plain sites in the Southeastern United States. Repeated removal of litter by raking and the loss of surface organic matter from controlled burns can affect the...

Skin-Friction Measurements at Subsonic and Transonic Mach Numbers with Embedded-Wire Gages

DTIC Science & Technology

1981-01-01

Model ................................... 17 9. Boundary-Layer Rake Installation on EBOR Model...boundary-layer total pressure rake eliminates this bulky mechanism and the long data acquisition time, but it introduces interferences which affect the...its construction. Further, boundary-layer rakes are restricted to measurements in thick boundary layers. Surface pressure probes such as Stanton tubes

Calibration of a pitot-static rake

NASA Technical Reports Server (NTRS)

Stump, H. P.

1977-01-01

A five-element pitot-static rake was tested to confirm its accuracy and determine its suitability for use at Langley during low-speed tunnel calibration primarily at full-scale tunnel. The rake was tested at one airspeed of 74 miles per hour (33 meters per second) and at pitch and yaw angles of 0 to + or - 20 degrees in 4 deg increments.

Effect of Geometric Parameters on the Performance of Second Throat Annular Steam Ejectors

DTIC Science & Technology

1991-07-01

Cell Pressure versus Rake Average Exit Pitot Pressure . . . . . . . . . . . 42 15. Baseline Wall Pressure Profiles...diffuser exit plane pitot pressure rake . 2.5.2 Alternate Configurations Six alternate ejector diffuser configurations were tested. A summary of...along the walls of the diffusers to help characterize the flow. The ejector diffuser exit pitot pressure was measured with a 6-probe pitot pressure rake

Congruence between muscle activity and kinematics in a convergently derived prey-processing behavior.

PubMed

Konow, Nicolai; Camp, Ariel L; Sanford, Christopher P J

2008-08-01

Quantification of anatomical and physiological characteristics of the function of a musculoskeletal system may yield a detailed understanding of how the organizational levels of morphology, biomechanics, kinematics, and muscle activity patterns (MAPs) influence behavioral diversity. Using separate analyses of these organizational levels in representative study taxa, we sought patterns of congruence in how organizational levels drive behavioral modulation in a novel raking prey-processing behavior found in teleosts belonging to two evolutionarily distinct lineages. Biomechanically divergent prey (elusive, robust goldfish and sedentary, malleable earthworms) were fed to knifefish, Chitala ornata (Osteoglossomorpha) and brook trout, Salvelinus fontinalis (Salmoniformes). Electromyography recorded MAPs from the hyoid protractor, jaw adductor, sternohyoideus, epaxialis, and hypaxialis musculature, while sonomicrometry sampled deep basihyal kinesis and contractile length dynamics in the basihyal protractor and retractor muscles. Syntheses of our results with recent analyses of cranial morphology and raking kinematics showed that raking in Salvelinus relies on an elongated cranial out lever, extensive cranial elevation and a curved cleithrobranchial ligament (CBL), and that both raking MAPs and kinematics remain entirely unmodulated-a highly unusual trait, particularly among feeding generalists. Chitala had a shorter CBL and a raking power stroke involving increased retraction of the elongated pectoral girdle during raking on goldfish. The raking MAP was also modulated in Chitala, involving an extensive overlap between muscle activity of the preparatory and power stroke phases, driven by shifts in hypaxial timing and recruitment of the hyoid protractor muscle. Sonomicrometry revealed that the protractor hyoideus muscle stored energy from retraction of the pectoral girdle for ca. 5-20 ms after onset of the power stroke and then hyper-extended. This mechanism of elastic recoil in Chitala, which amplifies retraction of the basihyal during raking on goldfish without a significant increase in recruitment of the hypaxialis, suggests a unique mechanism of modulation based on performance-enhancing changes in the design and function of the musculoskeletal system.

2-Step Maximum Likelihood Channel Estimation for Multicode DS-CDMA with Frequency-Domain Equalization

NASA Astrophysics Data System (ADS)

Kojima, Yohei; Takeda, Kazuaki; Adachi, Fumiyuki

Frequency-domain equalization (FDE) based on the minimum mean square error (MMSE) criterion can provide better downlink bit error rate (BER) performance of direct sequence code division multiple access (DS-CDMA) than the conventional rake combining in a frequency-selective fading channel. FDE requires accurate channel estimation. In this paper, we propose a new 2-step maximum likelihood channel estimation (MLCE) for DS-CDMA with FDE in a very slow frequency-selective fading environment. The 1st step uses the conventional pilot-assisted MMSE-CE and the 2nd step carries out the MLCE using decision feedback from the 1st step. The BER performance improvement achieved by 2-step MLCE over pilot assisted MMSE-CE is confirmed by computer simulation.

Design and Calibration of a Flowfield Survey Rake for Inlet Flight Research

NASA Technical Reports Server (NTRS)

Flynn, Darin C.; Ratnayake, Nalin A.; Frederick, Michael

2009-01-01

Flowfield rake was designed to quantify the flowfield for inlet research underneath NASA DFRC s F-15B airplane. Detailed loads and stress analysis performed using CFD and empirical methods to assure structural integrity. Calibration data were generated through wind tunnel testing of the rake. Calibration algorithm was developed to determine the local Mach and flow angularity at each probe. RAGE was flown November, 2008. Data is currently being analyzed.

Heat Transfer Due to Shock Wave Turbulent Boundary Layer Interactions on High Speed Weapon Systems

DTIC Science & Technology

1974-04-01

Thermocouple Location. ............ 20 8 Pressure Tap LoceL.lons ............ 23 9 Pitot Pressurp Rake Detail and Profile Measurement Stations... Pitot Pressure Profile Measurements - Pitot pressure measure- ments were made with a NASA Langley five-probe pitot pressure rake at the axial location...defined in Figure 6. Figure 9 is a schematic illustration providing the dimensions of the rake and the pitot pressure profile measure- ment stations. The

Coulomb stress analysis of the 21 February 2008 Mw= 6.0 Wells, Nevada, earthquake

USGS Publications Warehouse

Sevilgen, Volkan

2011-01-01

Static Coulomb stress changes imparted by the February 21, 2008 Wells, Nevada earthquake are calculated, using an 8 x 6 km rectangular patch with a uniform slip as a source fault. Stress changes are resolved on nearby active faults using their rake, dip, and strike direction, assuming a fault friction of 0.4. The largest Coulomb stress increase (0.2 bars) imparted to surrounding major active faults from the Wells earthquake occurs on the Clover Hill fault, which may be the southern continuation of the ruptured fault. A 0.1 bar Coulomb stress increase is calculated on the western Snake Mountains fault. Coulomb stress decreases of 0.5 bars are calculated for the northern parts of the Independence and Ruby Mountains faults. The Coulomb stress change is calculated on relocated aftershocks assuming that they have the same strike, dip, and rake, as the source fault. Under this assumption, 75% of the aftershocks received a Coulomb stress increase.

Identification of atmospheric structure by coherent microwave sounding

NASA Technical Reports Server (NTRS)

Birkemeier, W. P.

1969-01-01

Two atmospheric probing experiments involving beyond-the-horizon propagation of microwave signals are reported. In the first experiment, Doppler-shift caused by the cross path wind is measured by a phase lock receiver with the common volume displaced in azimuth from the great circle. Variations in the measured Doppler shift values are explained in terms of variations in atmospheric structure. The second experiment makes use of the pseudorandom sounding signal used in a RAKE communication system. Both multipath delay and Doppler shift are provided by the receiver, permitting the cross section of the atmospheric layer structure to be deduced.

The numerical study of the rake angle of impeller blade in centrifugal compressor

NASA Astrophysics Data System (ADS)

Drozdov, A.; Galerkin, Y.

2017-08-01

Investigated impellers have blade surfaces formed by straight generatrix. Blade profiles on shroud and disc surfaces are optimized by velocity diagram control (inviscid, quasi-three dimensional calculations). The blade profiles at hub and shroud blade-to-blade surfaces must be coordinated. A designer can choose the generatrix position at a trailing edge for it. The position is defined by the rake angle that is the angle between a trailing edge generatrix and a meridional plane. Two stages with 3D impellers, vaneless diffusers and return channels were investigated. Seven candidates of impellers of these stages with rake angles in range plus-minus 30 degrees were designed and investigated by quasi-three-dimensional inviscid calculation. CFD-calculations were made for the stages with these impellers. The optimal rake angle is minus 20 degrees for the high flow rate impeller due to lesser blade surface area and favorable meridian velocity field. Zero rake angle is optimal for the medium flow rate impeller where blade surface area is not so important. The combination of inviscid and viscid calculations is the informative instrument for further studies.

34. HILLMAN BARGE AND CONSTRUCTION COMPANY EMPLOYEES EXAMINING BARGE RAKE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. HILLMAN BARGE AND CONSTRUCTION COMPANY EMPLOYEES EXAMINING BARGE RAKE PART PATTERN, NORTHWEST MOLD LOFT - Hillman Barge & Construction Company, Paul Thomas Boulevard, Brownsville, Fayette County, PA

Investigations on the Effect of Steady and Pulsed Surface. Thermal Perturbations on the Hypersonic Flow-Field Over a Flat Plate and a Sharp Cone

DTIC Science & Technology

2010-03-10

achieved by setting proper driver and driven pressures. A calibration of the tunnel was done for the decided freestream conditions with a pitot rake ...measurement. A rake of 12 pitot probes spanning the diameter of the nozzle (300 mm) was placed facing the freestream. The pitot pressures were... pitot rake and shock tube measurements, the freestream conditions for each of the observed rupture pressure are estimated. It was observed that of

Investigation of Differences Between Measured and Predicted Pressures in AEDC/VKF Hypersonic Tunnel B

DTIC Science & Technology

1997-01-01

coordinates are presented in Fig. 4b. The primary calibration data used in this paper is derived from the rake . The 42 pitot probes cov- ered a range...the lateral (YT) direction. Figures 5 and 6 show examples of the pitot pressure and total temperature rake data from a lateral survey and American...Figure 5. Rake pitot measurements, XT = 16 in. 0 10 YT, in. b. Local Mach number 20 Total Temperature Contours, R Static Temperature Contours, R

Characteristics of Perforated Diffusers at Free-Stream Mach Number 1.90

DTIC Science & Technology

1950-05-08

deg) Subscripts: 0 free stream 1 inlet entrance 2 Inlet throat 3 pitot -static rake in simulated combustion chamber 4 outlet of simulated...consisted of a 40-tube pitot -static survey rake located 0.55 combust Ion-chamber diameter downstream of the outlet of the subsonic diffuser (fig. 8(b...The rake was so designed that eaoh pitot -static tube was located at the oentroid of one of the forty equal area segments Into which the combustion

Astronaut Harrison Schmitt collects lunar rake samples during EVA

NASA Image and Video Library

1972-12-11

AS17-134-20425 (11 Dec. 1972) --- Scientist-astronaut Harrison H. Schmitt, lunar module pilot, collects lunar rake samples at Station 1 during the first Apollo 17 extravehicular activity (EVA) at the Taurus-Littrow landing site. This picture was taken by astronaut Eugene Cernan, commander. The lunar rake, an Apollo lunar geology hand tool, is used to collect discrete samples of rocks and rock chips ranging in size from one-half inch (1.3 centimeter) to one inch (2.5 centimeter).

Comparison of conditional sampling and averaging techniques in a turbulent boundary layer

NASA Astrophysics Data System (ADS)

Subramanian, C. S.; Rajagopalan, S.; Antonia, R. A.; Chambers, A. J.

1982-10-01

A rake of cold wires was used in a slightly heated boundary layer to identify coherent temperature fronts. An X-wire/cold-wire arrangement was used simultaneously with the rake to provide measurements of the longitudinal and normal velocity fluctuations and temperature fluctuations. Conditional averages of these parameters and their products were obtained by application of conditional techniques (VITA, HOLE, BT, RA1, and RA3) based on the detection of temperature fronts using information obtained at only one point in space. It is found that none of the one-point detection techniques is in good quantitative agreement with the rake detection technique, the largest correspondence being 51%. Despite the relatively poor correspondence between the conditional techniques, these techniques, with the exception of HOLE, produce conditional averages that are in reasonable qualitative agreement with those deduced using the rake.

Development of a Rotating Rake Array for Boundary-Layer-Ingesting Fan-Stage Measurements

NASA Technical Reports Server (NTRS)

Wolter, John D.; Arend, David J.; Hirt, Stefanie M.; Gazzaniga, John A.

2017-01-01

The recent Boundary-Layer-Ingesting Inlet/Distortion Tolerant Fan wind tunnel experiment at NASA Glenn Research Center's 8- by 6-foot Supersonic Wind Tunnel (SWT) examined the performance of a novel inlet and fan stage that was designed to ingest the vehicle boundary layer in order to take advantage of a predicted overall propulsive efficiency benefit. A key piece of the experiment's instrumentation was a pair of rotating rake arrays located upstream and downstream of the fan stage. This paper examines the development of these rake arrays. Pre-test numerical solutions were sampled to determine placement and spacing for rake pressure and temperature probes. The effects of probe spacing and survey density on the repeatability of survey measurements was examined. These data were then used to estimate measurement uncertainty for the adiabatic efficiency.

Development of a Rotating Rake Array for Boundary-Layer-Ingesting Fan-Stage Measurements

NASA Technical Reports Server (NTRS)

Wolter, John D.; Arend, David J.; Hirt, Stefanie M.; Gazzaniga, John A.

2017-01-01

The recent Boundary-Layer-Ingesting Inlet/Distortion Tolerant Fan wind tunnel experiment at NASA Glenn Research Center's 8-foot by 6-foot supersonic wind tunnel examined the performance of a novel inlet and fan stage that was designed to ingest the vehicle boundary layer in order to take advantage of a predicted overall propulsive efficiency benefit. A key piece of the experiment's instrumentation was a pair of rotating rake arrays located upstream and downstream of the fan stage. This paper examines the development of these rake arrays. Pre-test numerical solutions were sampled to determine placement and spacing for rake pressure and temperature probes. The effects of probe spacing and survey density on the repeatability of survey measurements was examined. These data were then used to estimate measurement uncertainty for the adiabatic efficiency.

Cornice Detail of Rake, Cornice Detail of Eave, Wood DoubleHung ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Cornice Detail of Rake, Cornice Detail of Eave, Wood Double-Hung Window Details, Wood Door Details - Boxley Grist Mill, Boxley vicinity on State Route 43, Buffalo National River, Ponca, Newton County, AR

Shock Boundary Layer Interaction Flow Control with Micro Vortex Generators

DTIC Science & Technology

2011-05-01

Pitot rake ( p̄02p01 ) u = time-averaged streamwise velocity ufs = time-averaged freestream streamwise velocity u∗ = √ τw ρw = wall-shear velocity w...upstream of the normal shock-wave 2 = station 2, at the Pitot rake location I. Introduction With the exception of the scramjet, all current air-breathing...to this.7 1 shock holder near-normal shock μVGs 123 143 14 hole Pitot rake 6o x vg variable φ cylinder mounted on the centre-line 380 M ∞ =1.4

Astronaut Harrison Schmitt collects lunar rake samples during EVA

NASA Image and Video Library

1972-12-11

AS17-134-20426 (11 Dec. 1972) --- Scientist-astronaut Harrison H. Schmitt collects lunar rake samples at Station 1 during the first Apollo 17 extravehicular activity (EVA) at the Taurus-Littrow landing site. This picture was taken by astronaut Eugene A. Cernan, Apollo 17 commander. Schmitt is the lunar module pilot. The Lunar Rake, an Apollo Lunar Geology Hand Tool, is used to collect discrete samples of rocks and rock chips ranging in size from one-half inch (1.3 cm) to one inch (2.5 cm).

Evaluation of beach grooming techniques on Escherichia coli density in foreshore sand at North Beach, Racine, WI

USGS Publications Warehouse

Kinzelman, Julie L.; Whitman, Richard L.; Byappanahalli, Muruleedhara N.; Jackson, Emma; Bagley, Robert C.

2003-01-01

Elevated levels of Escherichia coli(E. coli) in bathing waters at North Beach, a popular recreational site in Racine, Wisconsin, have been a persistent problem often resulting in the issuance of poor water quality advisories. Moreover, waterfowl (mostly Larus delawarensis and L. argentatus) in nearshore and offshore areas are common and may serve as non-point sources for bacterial contamination of recreational waters. Current beach management practice involves daily mechanical grooming of the nearshore sand for aesthetics and removal of hazardous debris. However, this practice has not been evaluated in terms of its effects on E. coli loading to beach sand and potential introduction to contiguous swimming water. In this study, we tested E. coli responses to three treatments: mechanical groomer, daily and twice weekly hand raking, and a control (no raking/grooming). A randomized block design consisted of replicated treatments and one control (10 each), for a total of 40 blocks sampled daily for 10 days. Foreshore sand samples were collected by hand coring to an average depth of 10 cm. Median E. colirecovered were 73 (mechanically groomed), 27 (hand-raked daily), 32 (hand-raked twice weekly), and 22 (control) colony-forming units (CFU) per gram dry weight sand. E. colicounts in sand that was groomed were significantly higher than hand rakings and control (p <0.0001), and there was no significant difference between control and raking treatments (p<0.01). This study demonstrates the beach management implications related to grooming efficacy and the importance of understanding non-point sources of bacterial contamination.

Rotating rake design for unique measurement of fan-generated spinning acoustic modes

NASA Technical Reports Server (NTRS)

Konno, Kevin E.; Hausmann, Clifford R.

1993-01-01

In light of the current emphasis on noise reduction in subsonic aircraft design, NASA has been actively studying the source of and propagation of noise generated by subsonic fan engines. NASA/LeRC has developed and tested a unique method of accurately measuring these spinning acoustic modes generated by an experimental fan. This mode measuring method is based on the use of a rotating microphone rake. Testing was conducted in the 9 x 15 Low-speed Wind Tunnel. The rotating rake was tested with the Advanced Ducted Propeller (ADP) model. This memorandum discusses the design and performance of the motor/drive system for the fan-synchronized rotating acoustic rake. This novel motor/drive design approach is now being adapted for additional acoustic mode studies in new test rigs as baseline data for the future design of active noise control for subsonic fan engines. Included in this memorandum are the research requirements, motor/drive specifications, test performance results, and a description of the controls and software involved.

5. UPSTREAM VIEW OF THE TRASH RAKES, GATES AND GATELIFTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. UPSTREAM VIEW OF THE TRASH RAKES, GATES AND GATE-LIFTING MECHANISMS FOR THE POST FALLS DAM AND POWERHOUSE, LOOKING NORTHWEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

Effect of Cutting Angle and Depth of Cut on the Occurrence of Chipped Grain on Sycamore

Treesearch

Harold A. Stewart

1970-01-01

Sycamore specimens were planned with various combinations of depths of cut and rake angles. Depths of cut up to 1/16 inch had no significant effect on the occurrence of chipped grain in sycamore but rake angle did.

1. EXISTING TRASH RAKE STRUCTURE AND STEEL IBEAM TRACK, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EXISTING TRASH RAKE STRUCTURE AND STEEL I-BEAM TRACK, LOOKING EAST/NORTHEAST. - Washington Water Power Spokane River Upper Falls Hydroelectric Development, Gates & Gate-Lifting Mechanisms, Spokane River, approximately 0.5 mile northeast of intersection of Spokane Falls Boulevard & Post Street, Spokane, Spokane County, WA

An Analysis of Thrust Normalization of Ground Flowfield Pressures, Temperatures, and Velocities, for an AV-8B -408 Harrier During Hover

NASA Technical Reports Server (NTRS)

Naumowicz, Tim; Hange, Craig; Olson, Lawrence E. (Technical Monitor)

1998-01-01

An external environment test for an AV-8B Harrier during hover and vertical operations was conducted at NAWCAD at Patuxent River, Maryland in July 1997. Four boundary layer rakes were instrumented with static and total pressures, and thermocouples for measuring temperatures. These rakes were installed at 30, 50, 75, and 100 foot from the hover center. The 50 ft and 100 ft rakes were offset 20 deg from the other two to minimize interference effects. In order to measure a complete flowfield footprint, it was necessary to have the Harrier change its heading relative to the rakes from 0 to 180 deg. A 20 deg increment in azimuth was used. This permitted the four rakes to measure the flowfield at 72 locations relative to the aircraft. However, as the Harrier burns fuel, the hover thrust must be reduced by the pilot in order to maintain a constant height above ground. The typical test procedure employed was: (1) vertical takeoff at an initial heading; (2) 20 second hover dwell at that heading; (3) pedal turn to a second heading, followed by a 20 second dwell hover; (4) pedal turn to a third heading, followed by a 20 second dwell hover; and (5) vertical landing at the third heading. Additional information is contained in the original extended abstract.

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

... nonhuman primates come in contact must be spot-cleaned daily and sanitized in accordance with § 3.84 of... bedding, sand, gravel, grass, or other similar material, and planted enclosures must be raked or spot.... Contaminated material must be removed or replaced whenever raking and spot cleaning does not eliminate odors...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which nonhuman primates come in contact must be spot-cleaned daily and sanitized in... must be raked or spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be removed or replaced whenever raking and spot cleaning...

Asphalt Raking. Instructor Manual. Trainee Manual.

ERIC Educational Resources Information Center

Laborers-AGC Education and Training Fund, Pomfret Center, CT.

This packet consists of the instructor and trainee manuals for an asphalt raking course. The instructor manual contains a course schedule for 4 days of instruction, content outline, and instructor outline. The trainee manual is divided into five sections: safety, asphalt basics, placing methods, repair and patching, and clean-up and maintenance.…

Human See, Human Do.

ERIC Educational Resources Information Center

Tomasello, Michael

1997-01-01

A human demonstrator showed human children and captive chimpanzees how to drag food or toys closer using a rakelike tool. One side of the rake was less efficient than the other for dragging. Chimps tried to reproduce results rather than methods while children imitated and used the more efficient rake side. Concludes that imitation leads to…

An application of wake survey rakes to the experimental determination of thrust for a propeller driven aircraft

NASA Technical Reports Server (NTRS)

Hall, K. R.; Miley, S. J.; Tsai, H. J.

1981-01-01

The lack of slipstream static pressure distribution seriously affected the results but recommendations for removing the deficiency are discussed. The wake survey rake is shown to be a valuable tool in aircraft flight testing. Flow characteristics in the wake of the propeller were examined.

2D simulations of orthogonal cutting of CFRP: Effect of tool angles on parameters of cut and chip morphology

NASA Astrophysics Data System (ADS)

Benhassine, Mehdi; Rivière-Lorphèvre, Edouard; Arrazola, Pedro-Jose; Gobin, Pierre; Dumas, David; Madhavan, Vinay; Aizpuru, Ohian; Ducobu, François

2018-05-01

Carbon-fiber reinforced composites (CFRP) are attractive materials for lightweight designs in applications needing good mechanical properties. Machining of such materials can be harder than metals due to their anisotropic behavior. In addition, the combination of the fibers and resin mechanical properties must also include the fiber orientation. In the case of orthogonal cutting, the tool inclination, rake angle or cutting angle usually influence the cutting process but such a detailed investigation is currently lacking in a 2D configuration. To address this issue, a model has been developed with Abaqus Explicit including Hashin damage. This model has been validated with experimental results from the literature. The effects of the tool parameters (rake angle, clearance angle) on the tool cutting forces, CFRP chip morphology and surface damage are herewith studied. It is shown that 90° orientation for the CFRP increases the surface damage. The rake angle has a minimal effect on the cutting forces but modifies the chip formation times. The feed forces are increased with increasing rake angle.

An analytical method on the surface residual stress for the cutting tool orientation

NASA Astrophysics Data System (ADS)

Li, Yueen; Zhao, Jun; Wang, Wei

2010-03-01

The residual stress is measured by choosing 8 kinds orientations on cutting the H13 dies steel on the HSM in the experiment of this paper. The measured data shows on that the residual stress exists periodicity for the different rake angle (β) and side rake angle (θ) parameters, further study find that the cutting tool orientations have closed relationship with the residual stresses, and for the original of the machined residual stress on the surface from the cutting force and the axial force, it can be gained the simply model of tool-workpiece force, using the model it can be deduced the residual stress model, which is feasible to calculate the size of residual stress. And for almost all the measured residual stresses are compressed stress, the compressed stress size and the direction could be confirmed by the input data for the H13 on HSM. As the result, the residual stress model is the key for optimization of rake angle (β) and side rake angle (θ) in theory, using the theory the more cutting mechanism can be expressed.

Orthogonal cutting of cancellous bone with application to the harvesting of bone autograft.

PubMed

Malak, Sharif F F; Anderson, Iain A

2008-07-01

Autogenous bone graft harvesting results in cell death within the graft and trauma at the donor site. The latter can be mitigated by using minimally invasive tools and techniques, while cell morbidity may be reduced by improving cutter design and cutting parameters. We have performed orthogonal cutting experiments on bovine cancellous bone samples, to gain a basic understanding of the cutting mechanism and to determine design guidelines for tooling. Measurements were performed at cutting speeds from 11.2 to 5000 mm/min, with tool rake angles of 23 degrees, 45 degrees and 60 degrees, and depths of cut in the range of 0.1-3.0 mm. Horizontal and vertical cutting forces were measured, and the chip formation process video recorded. Continuous chip formation was observed for rake angles of 45 degrees and 60 degrees , and depths of cut greater than 0.8 mm. Chip formation for depths of cut greater than 1.0 mm was accompanied by bone marrow extruding out of the free surfaces and away from the rake face. Specific cutting energies decreased with increasing rake angle, increasing depth of cut and increasing cutting speed. Our orthogonal cutting experiments showed that a rake angle of 60 degrees and a depth of cut of 1mm, will avoid excessive fragmentation, keep specific cutting energy low and promote bone marrow extrusion, which may be beneficial for cell survival. We demonstrate how drill bit clearance angle and feed rate can be calculated facilitating a 1mm depth of cut.

Reproductive ecology of American Oystercatchers nesting on shell rakes

USGS Publications Warehouse

Jodice, Patrick G.R.; Thibault, Janet M.; Collins, S.A.; Spinks, Mark D.; Sanders, Felicia J.

2014-01-01

Degradation of nesting habitat for coastal birds has led to the use of nontraditional nesting habitat. The American Oystercatcher (Haematopus palliatus) is listed as a "Species of High Concern'' by the U. S. Shorebird Conservation Plan and is declining in the southern portion of its U. S. breeding range, where ~ 50% of breeding oystercatchers nest on shell substrate instead of beachfront habitat. We measured daily survival rates during incubation and chick rearing in shell rake habitats over five breeding seasons in the Cape Romain region of South Carolina, USA. Of 354 nesting attempts monitored, 16.1% hatched at least one egg. During incubation, daily survival rate was 0.938, corresponding to 22.8% success to hatching (nest success). For broods, daily survival was 0.991, or 74.0% success from hatching to fledging. Productivity in the Cape Romain region is primarily being lost during the incubation phase, when nests are exposed to overwash and predation. Mobile chicks may, however, be able to avoid flood events or predators by relocating to higher or more protected portions of a shell rake. Based on comparative data for American Oystercatchers from elsewhere in their range, it does not appear that shell rakes in the Cape Romain region are inferior breeding habitat. Our data suggest that conservation actions targeting nest and chick loss from flooding and predation have the greatest opportunity to enhance reproductive success in this core breeding area, and that an assessment of the availability, structure, avian use, and protection status of shell rakes is warranted.

Flight Test Results from the Rake Airflow Gage Experiment on the F-15B Airplane

NASA Technical Reports Server (NTRS)

Frederick, Michael A.; Ratnayake, Nalin A.

2010-01-01

The Rake Airflow Gage Experiment involves a flow-field survey rake that was flown on the Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center using the Dryden F-15B research test bed airplane. The objective of this flight test was to ascertain the flow-field angularity, local Mach number profile, total pressure distortion, and dynamic pressure at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment. This new mixed-compression, supersonic inlet is planned for flight test in the near term. Knowledge of the flow-field characteristics at this location underneath the airplane is essential to flight test planning and computational modeling of the new inlet, and it is also applicable for future propulsion systems research that may use the Propulsion Flight Test Fixture. This report describes the flight test preparation and execution, and the local flowfield properties calculated from pressure measurements of the rake. Data from the two Rake Airflow Gage Experiment research flights demonstrate that the F-15B airplane, flying at a free-stream Mach number of 1.65 and a pressure altitude of 40,000 ft, would achieve the desired local Mach number for the future inlet flight test. Interface plane distortion levels of 2 percent and a local angle of attack of 2 were observed at this condition. Alternative flight conditions for future testing and an exploration of certain anomalous data also are provided.

Flight Test Results from the Rake Airflow Gage Experiment on the F-15B Airplane

NASA Technical Reports Server (NTRS)

Frederick, Michael A.; Ratnayake, Nalin A.

2011-01-01

The Rake Airflow Gage Experiment involves a flow-field survey rake that was flown on the Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center using the Dryden F-15B research test bed airplane. The objective of this flight test was to ascertain the flow-field angularity, local Mach number profile, total pressure distortion, and dynamic pressure at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment. This new mixed-compression, supersonic inlet is planned for flight test in the near term. Knowledge of the flow-field characteristics at this location underneath the airplane is essential to flight test planning and computational modeling of the new inlet, an< it is also applicable for future propulsion systems research that may use the Propulsion Flight Test Fixture. This report describes the flight test preparation and execution, and the local flow-field properties calculated from pressure measurements of the rake. Data from the two Rake Airflow Gage Experiment research flights demonstrate that the F-15B airplane, flying at a free-stream Mach number of 1.65 and a pressure altitude of 40,000 ft, would achieve the desired local Mach number for the future inlet flight test. Interface plane distortion levels of 2 percent and a local angle of attack of -2 deg were observed at this condition. Alternative flight conditions for future testing and an exploration of certain anomalous data also are provided.

10. CLOSEUP VIEW OF THE TRASH RAKES, THEIR LIFTING MECHANISM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. CLOSE-UP VIEW OF THE TRASH RAKES, THEIR LIFTING MECHANISM (RIGHT FOREGROUND), AND CLUTCHES THAT OPEN AND CLOSE THE SIX INTAKE GATES ON THE POST FALLS POWERHOUSE, LOOKING WEST. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

A survey of aerobraking orbital transfer vehicle design concepts

NASA Technical Reports Server (NTRS)

Park, Chul

1987-01-01

The five existing design concepts of the aerobraking orbital transfer vehicle (namely, the raked sphere-cone designs, conical lifting-brake, raked elliptic-cone, lifting-body, and ballute) are reviewed and critiqued. Historical backgrounds, and the geometrical, aerothermal, and operational features of these designs are reviewed first. Then, the technological requirements for the vehicle (namely, navigation, aerodynamic stability and control, afterbody flow impingement, nonequilibrium radiation, convective heat-transfer rates, mission abort and multiple atmospheric passes, transportation and construction, and the payload-to-vehicle weight requirements) are delineated by summarizing the recent advancements made on these issues. Each of the five designs are critiqued and rated on these issues. The highest and the lowest ratings are given to the raked sphere-cone and the ballute design, respectively.

Comparison of Engine/Inlet Distortion Measurements with MEMS and ESP Pressure Sensors

NASA Technical Reports Server (NTRS)

Soto, Hector L.; Hernandez, Corey D.

2004-01-01

A study of active-flow control in a small-scale boundary layer ingestion inlet was conducted at the NASA Langley Basic Aerodynamic Research Tunnel (BART). Forty MEMS pressure sensors, in a rake style configuration, were used to examine both the mean (DC) and high frequency (AC) components of the total pressure across the inlet/engine interface plane. The mean component was acquired and used to calculate pressure distortion. The AC component was acquired separately, at a high sampling rate, and is used to study the unsteady effects of the active-flow control. An identical total pressure rake, utilizing an Electronically Scanned Pressure (ESP) system, was also used to calculate distortion; a comparison of the results obtained using the two rakes is presented.

Intensive straw harvesting, fertilization, and fertilizer source affect nitrogen mineralization and soil labile carbon of a loblolly pine plantation

Treesearch

K. Ellum; H.O. Liechty; M.A. Blazier

2013-01-01

Straw harvesting can supplement traditional revenues generated by loblolly pine (Pinus taeda L.) plantation management. However, repeated raking may alter soil properties and nutrition. In northcentral Louisiana, a study was conducted to evaluate the long-term effects of intensive straw raking and fertilizer source (inorganic or organic) on nitrogen...

Evaluation of Federal Aviation Administration Engine Exhaust Sampling Rake.

DTIC Science & Technology

1977-06-01

Engine exit total pressure - Pt7 " High turbine discharge temperature - Tt65,6 . Engine exit total temperature - Tt7 - Burner pressure - Ps4 0 Total...illustrated by Figure 22, a plot of Ps4 /Pt7 (expansion thru the turbine) vs. EPR (Pt7/Pt2). This plot indicates that the ECCP rake has no measurable effect on

67. September 1913 "No. 103. Oil being applied and raked ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

67. September 1913 "No. 103. Oil being applied and raked in, oil treated earth surface, experimental section. The frame in foreground was 1 x 5 yards, each square yard being indicated thereon, by which it was possible to determine the amount of oil placed in each square yard." - Crater Lake National Park Roads, Klamath Falls, Klamath County, OR

Design and Calibration of a Flowfield Survey Rake for Inlet Flight Research

NASA Technical Reports Server (NTRS)

Flynn, Darin C.; Ratnayake, Nalin A.; Frederick, Michael

2009-01-01

The Propulsion Flight Test Fixture at the NASA Dryden Flight Research Center is a unique test platform available for use on NASA's F-15B aircraft, tail number 836, as a modular host for a variety of aerodynamics and propulsion research. For future flight data from this platform to be valid, more information must be gathered concerning the quality of the airflow underneath the body of the F-15B at various flight conditions, especially supersonic conditions. The flow angularity and Mach number must be known at multiple locations on any test article interface plane for measurement data at these locations to be valid. To determine this prerequisite information, flight data will be gathered in the Rake Airflow Gauge Experiment using a custom-designed flowfield rake to probe the airflow underneath the F-15B at the desired flight conditions. This paper addresses the design considerations of the rake and probe assembly, including the loads and stress analysis using analytical methods, computational fluid dynamics, and finite element analysis. It also details the flow calibration procedure, including the completed wind-tunnel test and posttest data reduction, calibration verification, and preparation for flight-testing.

Cone-Probe Rake Design and Calibration for Supersonic Wind Tunnel Models

NASA Technical Reports Server (NTRS)

Won, Mark J.

1999-01-01

A series of experimental investigations were conducted at the NASA Langley Unitary Plan Wind Tunnel (UPWT) to calibrate cone-probe rakes designed to measure the flow field on 1-2% scale, high-speed wind tunnel models from Mach 2.15 to 2.4. The rakes were developed from a previous design that exhibited unfavorable measurement characteristics caused by a high probe spatial density and flow blockage from the rake body. Calibration parameters included Mach number, total pressure recovery, and flow angularity. Reference conditions were determined from a localized UPWT test section flow survey using a 10deg supersonic wedge probe. Test section Mach number and total pressure were determined using a novel iterative technique that accounted for boundary layer effects on the wedge surface. Cone-probe measurements were correlated to the surveyed flow conditions using analytical functions and recursive algorithms that resolved Mach number, pressure recovery, and flow angle to within +/-0.01, +/-1% and +/-0.1deg , respectively, for angles of attack and sideslip between +/-8deg. Uncertainty estimates indicated the overall cone-probe calibration accuracy was strongly influenced by the propagation of measurement error into the calculated results.

Effect of micro-scale texturing on the cutting tool performance

NASA Astrophysics Data System (ADS)

Vasumathy, D.; Meena, Anil

2018-05-01

The present study is mainly focused on the cutting performance of the micro-scale textured carbide tools while turning AISI 304 austenitic stainless steel under dry cutting environment. The texture on the rake face of the carbide tools was fabricated by laser machining. The cutting performance of the textured tools was further compared with conventional tools in terms of cutting forces, tool wear, machined surface quality and chip curl radius. SEM and EDS analyses have been also performed to better understand the tool surface characteristics. Results show that the grooves help in breaking the tool-chip contact leading to a lesser tool-chip contact area which results in reduced iron (Fe) adhesion to the tool.

Aerobraking orbital transfer vehicle

NASA Technical Reports Server (NTRS)

Scott, Carl D. (Inventor); Nagy, Kornel (Inventor); Roberts, Barney B. (Inventor); Ried, Robert C. (Inventor); Kroll, Kenneth R. (Inventor); Gamble, Joe (Inventor)

1989-01-01

An aerobraking orbital transfer vehicle which includes an aerobraking device which also serves as a heat shield in the shape of a raked-off elliptic or circular cone with a circular or elliptical base, and with an ellipsoid or other blunt shape nose. The aerobraking device is fitted with a toroid-like skirt and is integral with the support structure of the propulsion system and other systems of the space vehicle. The vehicle is intended to be transported in components to a space station in lower earth orbit where it is assembled for use as a transportation system from low earth orbit to geosynchronous earth orbit and return. Conventional guidance means are included for autonomous flight.

Experimental investigation of a newly designed supersonic wind tunnel

NASA Astrophysics Data System (ADS)

Wu, J.; Radespiel, R.

2015-06-01

The flow characteristics of the tandem nozzle supersonic wind tunnel at the Institute of Fluid Mechanics, Technische Universität Braunschweig, a are investigated. Conventional measurement techniques were utilized. The flow development is examined by pressure sensors installed at various streamwise positions. The temperature is measured in the storage tube and the settling chamber. The influence of flow treatment in the settling chamber on the flow quality is also studied. The flow quality of test section is evaluated by a 6-probe Pitot rake. The pressure fluctuations in the test section are studied by a sharp cone model. Eventually, good agreement between the measurements and numerical simulation of the tunnel design is achieved.

Low gravity liquid level sensor rake

NASA Technical Reports Server (NTRS)

Grayson, Gary D. (Inventor); Craddock, Jeffrey C. (Inventor)

2003-01-01

The low gravity liquid level sensor rake measures the liquid surface height of propellant in a propellant tank used in launch and spacecraft vehicles. The device reduces the tendency of the liquid propellant to adhere to the sensor elements after the bulk liquid level has dropped below a given sensor element thereby reducing the probability of a false liquid level measurement. The liquid level sensor rake has a mast attached internal to a propellant tank with an end attached adjacent the tank outlet. Multiple sensor elements that have an arm and a sensor attached at a free end thereof are attached to the mast at locations selected for sensing the presence or absence of the liquid. The sensor elements when attached to the mast have a generally horizontal arm and a generally vertical sensor.

A Future Moon Mission: Curatorial Statistics on Regolith Fragments Applicable to Sample Collection by Raking

NASA Technical Reports Server (NTRS)

Allton, J. H.; Bevill, T. J.

2003-01-01

The strategy of raking rock fragments from the lunar regolith as a means of acquiring representative samples has wide support due to science return, spacecraft simplicity (reliability) and economy [3, 4, 5]. While there exists widespread agreement that raking or sieving the bulk regolith is good strategy, there is lively discussion about the minimum sample size. Advocates of consor-tium studies desire fragments large enough to support petrologic and isotopic studies. Fragments from 5 to 10 mm are thought adequate [4, 5]. Yet, Jolliff et al. [6] demonstrated use of 2-4 mm fragments as repre-sentative of larger rocks. Here we make use of cura-torial records and sample catalogs to give a different perspective on minimum sample size for a robotic sample collector.

Survivorship of raked and unraked trees through prescribed fires in conifer forests in northeastern California

Treesearch

William F. Laudenslayer; George N. Steger; Jonathan Arnold

2008-01-01

Large diameter, old trees are an important component of functioning forests, as they provide habitat for many wildlife species and add value to the scenery along roads and trails that cross our National Forests and Parks. Tree mortality, from prescribed or wild fire, is of great concern to forests managers, especially mortality of those of large diameter. Raking away...

Influence of intertidal recreational fisheries and 'bouchot' mussel culture on bivalve recruitment.

PubMed

Toupoint, Nicolas; Barbier, Pierrick; Tremblay, Réjean; Archambault, Philippe; McKindsey, Christopher W; Winkler, Gesche; Meziane, Tarik; Olivier, Frédéric

2016-06-01

In coastal environments, fishing and aquaculture may be important sources of disturbance to ecosystem functioning, the quantification of which must be assessed to make them more sustainable. In the Chausey Archipelago, France, recreational fishing and commercial shellfish farming are the only two evident anthropogenic activities, dominated by bivalve hand-raking and 'bouchot' mussel culture, respectively. This study evaluates the impact of both activities on bivalve recruitment dynamics by comparing primary recruitment intensity (short-term effect) and recruitment efficiency (medium-term effect) by sampling bivalves in reference (undisturbed) and disturbed (i.e. subjected to hand-raking or in 'bouchot' mussel culture areas) parcels throughout and at the end of the recruitment season, respectively. Specific hypotheses evaluated were that (H1) bivalve hand-raking negatively affects bivalve recruitment and that (H2) 'bouchot' mussel culture promotes bivalve recruitment. Patterns in bivalve community structure in reference parcels (i.e. natural pattern) differed between initial and final recruitment, underlining the great importance of early post-settlement processes, particularly secondary dispersal. Primary recruitment intensity was inhibited in hand-raking parcels whereas it was promoted in 'bouchot' mussel culture parcels, but the effect on recruitment efficiency was muted for both activities due to post-settlement processes. Nevertheless, the importance of effects that occur during the first step of recruitment should not be ignored as they may affect bivalve communities and induce immediate consequences on the trophic web through a cascade effect. Finally, it is highlighted that hand-raking damages all life stages of the common cockle Cerastoderma edule, one of the major target species, suggesting that this activity should be managed with greater caution than is currently done. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design of a constant tension thermocouple rake suitable for flame studies

NASA Technical Reports Server (NTRS)

Ahuja, Sandeep; Miller, David L.

1993-01-01

An improved, spring-loaded thermocouple rake, suitable for studying flame structure, has been designed. This design keeps the thermocouple under tension thereby ensuring that the thermocouple does not droop due to the thermal expansion of the sensing wire when inserted in the flame. The present design allows the usage of thermocouple wire as small as 0.0508 mm and relative ease in changing thermocouple wire.

Noise Identification in a Hot Transonic Jet Using Low-Dimensional Methods

DTIC Science & Technology

2008-03-01

calibration between the nozzle static pressure (transducer) and total pressure ( pitot probe) reveals a nearly linear relationship between the two, exhibiting... rakes of hot-wires. Multi-point correlations of velocity components coupled with assumptions of homogeneity and periodicity in the jet flow flied...axisymmetric incompressible jet at one downstream position using an in-house designed rake of 138 hot-wires. The experiment was then carried out at multiple

Calibration of averaging total pressure flight wake rake and natural-laminar-flow airfoil drag certification

NASA Technical Reports Server (NTRS)

Irani, E.; Snyder, M. H.

1988-01-01

An averaging total pressure wake rake used by the Cessna Aircraft Company in flight tests of a modified 210 airplane with a laminar flow wing was calibrated in wind tunnel tests against a five-tube pressure probe. The model generating the wake was a full-scale model of the Cessna airplane wing. Indications of drag trends were the same for both instruments.

A sex difference in effect of prior experience on object-mediated problem-solving in gibbons.

PubMed

Cunningham, Clare; Anderson, James; Mootnick, Alan

2011-07-01

Understanding the functionally relevant properties of objects is likely facilitated by learning with a critical role for past experience. However, current evidence is conflicting regarding the effect of prior object exposure on acquisition of object manipulation skills. This may be due to the influence of life history variables on the capacity to benefit from such experience. This study assessed effect of task-relevant object exposure on object-mediated problem-solving in 22 gibbons using a raking-in task. Despite not using tools habitually, 14 gibbons spontaneously used a rake to obtain a reward. Having prior experience with the rake in an unrewarded context did not improve learning efficiency in males. However, females benefitted significantly from the opportunity to interact with the rake before testing, with reduced latencies to solution compared to those with no previous exposure. These results reflect potential sex differences in approach to novelty that moderate the possible benefits of prior experience. Due to their relatively high energetic requirements, reproductively active females may be highly motivated to explore potential resources; however, increased investment in developing offspring could make them more guarded in their investigations. Previous exposure that allows females to learn of an object's neutrality can offset this cautious exploration.

Pre-Flight Ground Testing of the Full-Scale HIFiRE-1 at Fully Duplicated Flight Conditions

DTIC Science & Technology

2008-05-14

survey rake installed in the test section to measure X ... -------- pitot pressure, static pressure and stagnation point heat transfer in . the...equilibrium at Figure 17. Photograph of Pitot Rake Assembly all points. This is a safe assumption, as the pressures and Mounted Inside Test Section of...measurement technique in supersonic and hypersonic test facilities, and the small size of the sensing element coupled with the insulating substrate

The AFFDL-Nielsen Flow-Field Study

DTIC Science & Technology

1976-04-01

76-18 1.0 INTRODUCTION This investigation was conducted in the von K ~ n Gas Dynamics Facility (VKF) Supersonic Wind Tunnel (A) for Nielsen...flow field-surveys, using a cone probe rake to determine the local velocity field; (2) pressure distributions on a store model; and (3) force and...moment data on a store model. In addition, free-stream (interference-free) data were obtained with the probe rake and on the force and pressure store

A flammability study of thin plastic film materials

NASA Technical Reports Server (NTRS)

Skinner, S. Ballou

1990-01-01

The Materials Science Laboratory at the Kennedy Space Center presently conducts flammability tests on thin plastic film materials by using a small needle rake method. Flammability data from twenty-two thin plastic film materials were obtained and cross-checked by using three different testing methods: (1) the presently used small needle rake; (2) the newly developed large needle rake; and (3) the previously used frame. In order to better discern the melting-burning phenomenon of thin plastic film material, five additional specific experiments were performed. These experiments determined the following: (1) the heat sink effect of each testing method; (2) the effect of the burn angle on the burn length or melting/shrinkage length; (3) the temperature profile above the ignition source; (4) the melting point and the fire point of each material; and (5) the melting/burning profile of each material via infrared (IR) imaging. The results of these experimentations are presented.

Effect of number of probes and their orientation on the calculation of several compressor face distortion descriptors

NASA Technical Reports Server (NTRS)

Stoll, F.; Tremback, J. W.; Arnaiz, H. H.

1979-01-01

A study was performed to determine the effects of the number and position of total pressure probes on the calculation of five compressor face distortion descriptors. This study used three sets of 320 steady state total pressure measurements that were obtained with a special rotating rake apparatus in wind tunnel tests of a mixed-compression inlet. The inlet was a one third scale model of the inlet on a YF-12 airplane, and it was tested in the wind tunnel at representative flight conditions at Mach numbers above 2.0. The study shows that large errors resulted in the calculation of the distortion descriptors even with a number of probes that were considered adequate in the past. There were errors as large as 30 and -50 percent in several distortion descriptors for a configuration consisting of eight rakes with five equal-area-weighted probes on each rake.

Investigation of Shock Diffusers at Mach Number 1.85. 2 - Projecting Double-Shock Cones

DTIC Science & Technology

1947-06-17

pitot - static rake located as shown in figure 1(a). Total-pressure recoveries were measured for a series of tip projections varied in minimum steps...is shown. The position of the pitot -static rake with which these distributions were .measured is shown in figure 1(a). The data points correspond...Schroeder SUMMARY An Investigation has "been undertaken in the Cleveland 18- by 18-Inch, supersonic tunnel to determine the total-pressure

Investigation of Shock Diffusers at Mach Number 1.85. 1 - Projecting Single Shock Cones

DTIC Science & Technology

1947-06-17

cylindrical simulated combustion chamber was used to vary the outlet area of the flow through the diffuser. The pitot -static rake , located as shown in the...Simulated combustion u chamber A 90° W •—Conical damper S Static-pressure orifice ps pitot -static "" rake ’ NATIONAL ADVISORY...recoveries were obtained with subsonic entrance flow. INTRODCJCTION For efficient conversion of the kinetic energy of a supersonic air stream into ram

Comparison of wind tunnel and flight test afterbody and nozzle pressures for a twin-jet fighter aircraft at transonic speeds

NASA Technical Reports Server (NTRS)

Nugent, Jack; Pendergraft, Odis C., Jr.

1987-01-01

Afterbody and nozzle pressures measured on a 1/12-scale model and in flight on a twin-jet fighter aircraft were compared as Mach number varied from 0.6 to 1.2, Reynolds number from 17.5 million to 302.5 million, and angle of attack from 1 to 7 deg. At Mach 0.6 and 0.8, nozzle pressure coefficient distributions and nozzle axial force coefficients agreed and showed good recompression. At Mach 0.9 and 1.2, flow complexity caused a loss in recompression for both flight and wind tunnel nozzle data. The flight data exhibited less negative values of pressure coefficient and lower axial force coefficients than did the wind tunnel data. Reynolds number effects were noted only at these Mach numbers. Jet temperature and mass flux ratio did not affect the comparisons of nozzle axial flow coefficient. At subsonic speeds, the levels of pressure coefficient distributions on the upper fuselage and lower nacelle surfaces for flight were less negative than those for the model. The model boundary layer thickness at the aft rake station exceeded that for the forward rake station and increased with increasing angle of attack. The flight boundary layer thickness at the aft rake station was less than that for the forward rake station and decreased with increasing angle of attack.

Constraints on the exploitation of the functional properties of objects in expert tool-using chimpanzees (Pan troglodytes).

PubMed

Povinelli, Daniel J; Frey, Scott H

2016-09-01

Many species exploit immediately apparent dimensions of objects during tool use and manufacture and operate over internal perceptual representations of objects (they move and reorient objects in space, have rules of operation to deform or modify objects, etc). Humans, however, actively test for functionally relevant object properties before such operations begin, even when no previous percepts of a particular object's qualities in the domain have been established. We hypothesize that such prospective diagnostic interventions are a human specialization of cognitive function that has been entirely overlooked in the neuropsychological literature. We presented chimpanzees with visually identical rakes: one was functional for retrieving a food reward; the other was non-functional (its base was spring-loaded). Initially, they learned that only the functional tool could retrieve a distant reward. In test 1, we explored if they would manually test for the rakes' rigidity during tool selection, but before using it. We found no evidence of such behavior. In test 2, we obliged the apes to deform the non-functional tool's base before using it, in order to evaluate whether this would cause them to switch rakes. It did not. Tests 3-6 attempted to focus the apes' attention on the functionally relevant property (rigidity). Although one ape eventually learned to abandon the non-functional rake before using it, she still did not attempt to test the rakes for rigidity prior to use. While these results underscore the ability of chimpanzees to use novel tools, at the same time they point toward a fundamental (and heretofore unexplored) difference in causal reasoning between humans and apes. We propose that this behavioral difference reflects a human specialization in how object properties are represented, which could have contributed significantly to the evolution of our technological culture. We discuss developing a new line of evolutionarily motivated neuropsychological research on action disorders. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modular Rake of Pitot Probes

NASA Technical Reports Server (NTRS)

Dunlap, Timothy A.; Henry, Michael W.; Homyk, Raymond P.

2004-01-01

The figure presents selected views of a modular rake of 17 pitot probes for measuring both transient and steady-state pressures in a supersonic wind tunnel. In addition to pitot tubes visible in the figure, the probe modules contain (1) high-frequency dynamic-pressure transducers connected through wires to remote monitoring circuitry and (2) flow passages that lead to tubes that, in turn, lead to remote steady-state pressure transducers. Prior pitot-probe rakes were fabricated as unitary structures, into which the individual pitot probes were brazed. Repair or replacement of individual probes was difficult, costly, and time-consuming because (1) it was necessary to remove entire rakes in order to unbraze individual malfunctioning probes and (2) the heat of unbrazing a failed probe and of brazing a new probe in place could damage adjacent probes. In contrast, the modules in the present probe are designed to be relatively quickly and easily replaceable with no heating and, in many cases, without need for removal of the entire rake from the wind tunnel. To remove a malfunctioning probe, one first removes a screw-mounted V-cross-section cover that holds the probe and adjacent probes in place. Then one removes a screw-mounted cover plate to gain access to the steady-state pressure tubes and dynamicpressure wires. Next, one disconnects the tube and wires of the affected probe. Finally, one installs a new probe in the reverse of the aforementioned sequence. The wire connections can be made by soldering, but to facilitate removal and installation, they can be made via miniature plugs and sockets. The connections between the probe flow passages and the tubes leading to the remote pressure sensors can be made by use of any of a variety of readily available flexible tubes that can be easily pulled off and slid back on for removal and installation, respectively.

Laminar Boundary Layer Stability Measurements at Mach 7 Including Wall Temperature Effects

DTIC Science & Technology

1977-11-01

Diagnostics were done by a four-probe rake bearing a pitot tube, a To probe and two hot films - a boundary layer hot film probe (BLHF) and a freestream hot...tunnel. Inset shows hot film probe close to the surface with second probe positioned higher to sample simultaneously the frcestream turbulence ( pitot ... rake away from the surface by small increments and taking readings at each stop. The readings were simultaneously recorded and reduced by the Tunnel B

Cross-Grain Knife Planing Improves Surface Quality and Utilization of Aspen

Treesearch

Harold A. Stewart

1971-01-01

Aspen at 6 percent moisture content was planed parallel to the grain and across the grain on a cabinet planer with a 25? rake angle, 1/16- and 1/32-inch depth of cut, and 20 knife marks per inch. Aspen was also cross-grain knife planed with a 45? rake angle, 1/32-, 1/16-, and 1/8-inch depths of cut, and 20, 10, 5, and 2.5 knife marks per inch. Cross-grain knife...

Wall Boundary Layer Measurements for the NASA Langley Transonic Dynamics Tunnel

NASA Technical Reports Server (NTRS)

Wieseman, Carol D.; Bennett, Robert M.

2007-01-01

Measurements of the boundary layer parameters in the NASA Langley Transonic Dynamics tunnel were conducted during extensive calibration activities following the facility conversion from a Freon-12 heavy-gas test medium to R-134a. Boundary-layer rakes were mounted on the wind-tunnel walls, ceiling, and floor. Measurements were made over the range of tunnel operation envelope in both heavy gas and air and without a model in the test section at three tunnel stations. Configuration variables included open and closed east sidewall wall slots, for air and R134a test media, reentry flap settings, and stagnation pressures over the full range of tunnel operation. The boundary layer thickness varied considerably for the six rakes. The thickness for the east wall was considerably larger that the other rakes and was also larger than previously reported. There generally was some reduction in thickness at supersonic Mach numbers, but the effect of stagnation pressure, and test medium were not extensive.

Research Results Of Stress-Strain State Of Cutting Tool When Aviation Materials Turning

NASA Astrophysics Data System (ADS)

Serebrennikova, A. G.; Nikolaeva, E. P.; Savilov, A. V.; Timofeev, S. A.; Pyatykh, A. S.

2018-01-01

Titanium alloys and stainless steels are hard-to-machine of all the machining types. Cutting edge state of turning tool after machining titanium and high-strength aluminium alloys and corrosion-resistant high-alloy steel has been studied. Cutting forces and chip contact arears with the rake surface of cutter has been measured. The relationship of cutting forces and residual stresses are shown. Cutting forces and residual stresses vs value of cutting tool rake angle relation were obtained. Measurements of residual stresses were performed by x-ray diffraction.

High-Subsonic Performance Characteristics and Boundary-Layer Investigations of a 12 deg 10-Inch-Inlet-Diameter Conical Diffuser

DTIC Science & Technology

1950-05-11

available condition supersonic flow was obtained as far as K.5 inches downstream from the diffueer inlet with a maximum Mach number of M % 1.5...Boundary—layer total-pressure measurements were made with the rake shown in figure k. The tubes varied in size from 0.030-Inch outside diameter...at the wall to 0.050—inch outside diameter farther out. A static-pressure tube was mounted on the rake to measure static pressures at the same

Experiments in Numerical Studies of Low Density and Real Gas Effects on Regions of Shock Wave/Boundary Layer Interaction in Hypervelocity Flows

DTIC Science & Technology

2006-06-01

Figure 13 Survey Rake containing Instrumentation to Measure Pitot and Static Pressure, Heating Distributions on Cylinders and Spheres, and Cone...35a and is in close agreement with the inviscid flow prediction in Figure 35b. Measurements made with a pitot pressure rake positioned at the end of...Velocity 15,00o 7 ’ DISOl• AglOrf (feet per sec) 10 N•’’ 10,000 47_T"___ ____ VIBATIONA Hypersonic 5,000 EXCITATION REGION Supersonic IDEAL GAS -Transonic 0

Fluid Dynamic and Acoustic Experiments on Turbomachine Rotors Subject to Variable Flow Conditions

DTIC Science & Technology

1990-03-31

conjunction with a standard pitot tube that is mounted in the wind tunnel test section upstream of the dynamometer system. The 4 manometer has a...generator." The smoke is then pumped into a "smoke rake ," in which it cools to ambient temperature and is directed the smoke into the inlet of the wind...34 and "smoke rake " are shown in Figures 5 and 6. A more complete explanation of the smoke generation process and apparatus is provided by Mueller (1983

An Innovative Flow-Measuring Device: Thermocouple Boundary Layer Rake

NASA Technical Reports Server (NTRS)

Hwang, Danny P.; Fralick, Gustave C.; Martin, Lisa C.; Wrbanek, John D.; Blaha, Charles A.

2001-01-01

An innovative flow-measuring device, a thermocouple boundary layer rake, was developed. The sensor detects the flow by using a thin-film thermocouple (TC) array to measure the temperature difference across a heater strip. The heater and TC arrays are microfabricated on a constant-thickness quartz strut with low heat conductivity. The device can measure the velocity profile well into the boundary layer, about 65 gm from the surface, which is almost four times closer to the surface than has been possible with the previously used total pressure tube.

Coseismic temporal changes of slip direction: the effect of absolute stress on dynamic rupture

USGS Publications Warehouse

Guatteri, Mariagiovanna; Spudich, P.

1998-01-01

We investigate the dynamics of rupture at low-stress level. We show that one main difference between the dynamics of high- and low-stress events is the amount of coseismic temporal rake rotation occurring at given points on the fault. Curved striations on exposed fault surfaces and earthquake dislocation models derived from ground-motion inversion indicate that the slip direction may change with time at a point on the fault during dynamic rupture. We use a 3D boundary integral method to model temporal rake variations during dynamic rupture propagation assuming a slip-weakening friction law and isotropic friction. The points at which the slip rotates most are characterized by an initial shear stress direction substantially different from the average stress direction over the fault plane. We show that for a given value of stress drop, the level of initial shear stress (i.e., the fractional stress drop) determines the amount of rotation in slip direction. We infer that seismic events that show evidence of temporal rake rotations are characterized by a low initial shear-stress level with spatially variable direction on the fault (possibly due to changes in fault surface geometry) and an almost complete stress drop.Our models motivate a new interpretation of curved and cross-cutting striations and put new constraints on their analysis. The initial rake is in general collinear with the initial stress at the hypocentral zone, supporting the assumptions made in stress-tensor inversion from first-motion analysis. At other points on the fault, especially away from the hypocenter, the initial slip rake may not be collinear with the initial shear stress, contradicting a common assumption of structural geology. On the other hand, the later part of slip in our models is systematically more aligned with the average stress direction than the early slip. Our modeling suggests that the length of the straight part of curved striations is usually an upper bound of the slip-weakening distance if this parameter is uniform over the fault plane, and the direction of the late part of slip of curved striations should have more weight in the estimate of initial stress direction.

Successive Interference Cancellation in Rake Receiver for CDMA Signals

DTIC Science & Technology

2009-06-01

Madkour [1], who worked on algorithms in 2002, to cancel out...Hadamard matrix is produced as shown in Figure 2 [2].  1 1H  1 1 2 1 1 1 1 1 1 H H H H H             2 2 4 2 2 1 1 1 1...1 1 1 1 1 1 1 1 1 1 1 1 H H H H H                    Figure 2. Production of Walsh functions. The

Accurate Bit Error Rate Calculation for Asynchronous Chaos-Based DS-CDMA over Multipath Channel

NASA Astrophysics Data System (ADS)

Kaddoum, Georges; Roviras, Daniel; Chargé, Pascal; Fournier-Prunaret, Daniele

2009-12-01

An accurate approach to compute the bit error rate expression for multiuser chaosbased DS-CDMA system is presented in this paper. For more realistic communication system a slow fading multipath channel is considered. A simple RAKE receiver structure is considered. Based on the bit energy distribution, this approach compared to others computation methods existing in literature gives accurate results with low computation charge. Perfect estimation of the channel coefficients with the associated delays and chaos synchronization is assumed. The bit error rate is derived in terms of the bit energy distribution, the number of paths, the noise variance, and the number of users. Results are illustrated by theoretical calculations and numerical simulations which point out the accuracy of our approach.

Calculation of sidewall boundary-layer parameters from rake measurements for the Langley 0.3-meter transonic cryogenic tunnel

NASA Technical Reports Server (NTRS)

Murthy, A. V.

1987-01-01

Correction of airfoil data for sidewall boundary-layer effects requires a knowledge of the boundary-layer displacement thickness and the shape factor with the tunnel empty. To facilitate calculation of these quantities under various test conditions for the Langley 0.3 m Transonic Cryogenic Tunnel, a computer program was written. This program reads the various tunnel parameters and the boundary-layer rake total head pressure measurements directly from the Engineering Unit tapes to calculate the required sidewall boundary-layer parameters. Details of the method along with the results for a sample case are presented.

Experimental and predicted pressure and heating distributions for an Aeroassist Flight Experiment vehicle in air at Mach 10

NASA Technical Reports Server (NTRS)

Micol, John R.

1989-01-01

The Aeroassisted Flight Experiment vehicle for whose scale model pressure and heat-transfer rate distributions have been measured in air at Mach 10 is a 60-deg elliptic cone, raked off at a 73-percent angle, with an ellipsoid nose and a skirt added to the base of the rake plane to reduce heating. The predictions of both an inviscid flow-field code and a Navier-Stokes solver are compared with measured values. Good agreement is obtained in the case of pressure distributions; the effect of Reynolds number on heat-transfer distributions is noted to be small.

Duct Mode Measurements on the TFE731-60 Full Scale Engine

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.; Konno, Kevin E.; Heidelberg, Laurence J.

2002-01-01

A continuously rotating rake with radial microphones was developed to measure the inlet and exhaust duct modes on a TFE731-60 turbofan engine. This was the first time the rotating rake technology was used on a production engine. The modal signature for the first three fan harmonics was obtained in the inlet and exhaust. Rotor-stator and rotor-strut interaction modes were measured. Total harmonic power was calculated over a range of fan speeds. Above sonic tip speed, the rotor locked mode was not strong enough to be identified, but the 'buzz-saw' noise at fan sub-harmonics was identified.

Flowfield measurements in the NASA Lewis Research Center 9- by 15-foot low-speed wind tunnel

NASA Technical Reports Server (NTRS)

Hughes, Christopher E.

1989-01-01

An experimental investigation was conducted in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel to determine the flow characteristics in the test section during wind tunnel operation. In the investigation, a 20-probe horizontally-mounted Pitot-static flow survey rake was used to obtain cross-sectional total and static pressure surveys at four axial locations in the test section. At each axial location, the cross-sectional flowfield surveys were made by repositioning the Pitot-static flow survey rake vertically. In addition, a calibration of the new wind tunnel rake instrumentation, used to determine the wind tunnel operating conditions, was performed. Boundary laser surveys were made at three axial locations in the test section. The investigation was conducted at tunnel Mach numbers 0.20, 0.15, 0.10, and 0.05. The test section profile results from the investigation indicate that fairly uniform total pressure profiles (outside the test section boundary layer) and fairly uniform static pressure and Mach number profiles (away from the test section walls and downstream of the test section entrance) exist throughout in the wind tunnel test section.

RLS Channel Estimation with Adaptive Forgetting Factor for DS-CDMA Frequency-Domain Equalization

NASA Astrophysics Data System (ADS)

Kojima, Yohei; Tomeba, Hiromichi; Takeda, Kazuaki; Adachi, Fumiyuki

Frequency-domain equalization (FDE) based on the minimum mean square error (MMSE) criterion can increase the downlink bit error rate (BER) performance of DS-CDMA beyond that possible with conventional rake combining in a frequency-selective fading channel. FDE requires accurate channel estimation. Recently, we proposed a pilot-assisted channel estimation (CE) based on the MMSE criterion. Using MMSE-CE, the channel estimation accuracy is almost insensitive to the pilot chip sequence, and a good BER performance is achieved. In this paper, we propose a channel estimation scheme using one-tap recursive least square (RLS) algorithm, where the forgetting factor is adapted to the changing channel condition by the least mean square (LMS)algorithm, for DS-CDMA with FDE. We evaluate the BER performance using RLS-CE with adaptive forgetting factor in a frequency-selective fast Rayleigh fading channel by computer simulation.

F-16XL ship #1 CAWAP flight

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

Aero-Thermal Calibration of the NASA Glenn Icing Research Tunnel (2012 Test)

NASA Technical Reports Server (NTRS)

Pastor-Barsi, Christine M.; Arrington, E. Allen; VanZante, Judith Foss

2012-01-01

A major modification of the refrigeration plant and heat exchanger at the NASA Glenn Icing Research Tunnel (IRT) occurred in autumn of 2011. It is standard practice at NASA Glenn to perform a full aero-thermal calibration of the test section of a wind tunnel facility upon completion of major modifications. This paper will discuss the tools and techniques used to complete an aero-thermal calibration of the IRT and the results that were acquired. The goal of this test entry was to complete a flow quality survey and aero-thermal calibration measurements in the test section of the IRT. Test hardware that was used includes the 2D Resistive Temperature Detector (RTD) array, 9-ft pressure survey rake, hot wire survey rake, and the quick check survey rake. This test hardware provides a map of the velocity, Mach number, total and static pressure, total temperature, flow angle and turbulence intensity. The data acquired were then reduced to examine pressure, temperature, velocity, flow angle, and turbulence intensity. Reduced data has been evaluated to assess how the facility meets flow quality goals. No icing conditions were tested as part of the aero-thermal calibration. However, the effects of the spray bar air injections on the flow quality and aero-thermal calibration measurements were examined as part of this calibration.

Functional morphology and biomechanics of the tongue-bite apparatus in salmonid and osteoglossomorph fishes

PubMed Central

Camp, Ariel L; Konow, Nicolai; Sanford, Christopher P J

2009-01-01

The tongue-bite apparatus and its associated musculoskeletal elements of the pectoral girdle and neurocranium form the structural basis of raking, a unique prey-processing behaviour in salmonid and osteoglossomorph fishes. Using a quantitative approach, the functional osteology and myology of this system were compared between representatives of each lineage, i.e. the salmonid Salvelinus fontinalis (N =10) and the osteoglossomorph Chitala ornata(N = 8). Divergence was found in the morphology of the novel cleithrobranchial ligament, which potentially relates to kinematic differences between the raking lineage representatives. Salvelinus had greater anatomical cross-sectional areas of the epaxial, hypaxial and protractor hyoideus muscles, whereas Chitala had greater sternohyoideus and adductor mandibulae mass. Two osteology-based biomechanical models (a third-order lever for neurocranial elevation and a modified four-bar linkage for hyoid retraction) showed divergent force/velocity priorities in the study taxa. Salvelinus maximizes both force (via powerful cranial muscles) and velocity (through mechanical amplification) during raking. In contrast, Chitala has relatively low muscle force but more efficient force transmission through both mechanisms compared with Salvelinus. It remains unclear if and how behavioural modulation and specializations in the post-cranial anatomy may affect the force/velocity trade-offs in Chitala. Further studies of tongue-bite apparatus morphology and biomechanics in a broader species range may help to clarify the role that osteology and myology play in the evolution of behavioural diversity. PMID:19438765

Golfer's Elbow

MedlinePlus

... your elbow can cause golfer's elbow. This includes painting, raking, hammering, chopping wood, using a computer, doing ... using older golfing irons, consider upgrading to lighter graphite clubs. If you play tennis, a racket with ...

Slip re-orientation in the oblique Abiquiu embayment, northern Rio Grande rift

NASA Astrophysics Data System (ADS)

Liu, Y.; Murphy, M. A.; Andrea, R. A.

2015-12-01

Traditional models of oblique rifting predict that an oblique fault accommodates both dip-slip and strike-slip kinematics. However, recent analog experiments suggest that slip can be re-oriented to almost pure dip-slip on oblique faults if a preexisting weak zone is present at the onset of oblique extension. In this study, we use fault slip data from the Abiquiu embayment in northern Rio Grande rift to test the new model. The Rio Grande rift is a Cenozoic oblique rift extending from southern Colorado to New Mexico. From north to south, it comprises three major half grabens (San Luis, Española, and Albuquerque). The Abiquiu embayment is a sub-basin of the San Luis basin in northern New Mexico. Rift-border faults are generally older and oblique to the trend of the rift, whereas internal faults are younger and approximately N-S striking, i.e. orthogonal to the regional extension direction. Rift-border faults are deep-seated in the basement rocks while the internal faults only cut shallow stratigraphic sections. It has been suggested by many that inherited structures may influence the Rio Grande rifting. Particularly, Laramide structures (and possibly the Ancestral Rockies as well) that bound the Abiquiu embayment strike N- to NW. Our data show that internal faults in the Abiquiu embayment exhibit almost pure dip-slip (rake of slickenlines = 90º ± 15º), independent of their orientations with respect to the regional extension direction. On the contrary, border faults show two sets of rakes: almost pure dip-slip (rake = 90º ± 15º) where the fault is sub-parallel to the foliation, and moderately-oblique (rake = 30º ± 15º) where the fault is high angle to the foliation. We conclude that slip re-orientation occurs on most internal faults and some oblique border faults under the influence of inherited structures. Regarding those border faults on which slip is not re-oriented, we hypothesize that it may be caused by the Jemez volcanism or small-scale mantle convection.

The Apollo 17 samples: The Massifs and landslide

NASA Technical Reports Server (NTRS)

Ryder, Graham

1992-01-01

More than 50 kg of rock and regolith samples, a little less than half the total Apollo 17 sample mass, was collected from the highland stations at Taurus-Littrow. Twice as much material was collected from the North Massif as from the South Massif and its landslide (the apparent disproportionate collecting at the mare sites is mainly a reflection of the large size of a few individual basalt samples). Descriptions of the collection, documentation, and nature of the samples are given. A comprehensive catalog is currently being produced. Many of the samples have been intensely studied over the last 20 years and some of the rocks have become very familiar and depicted in popular works, particularly the dunite clast (72415), the troctolite sample (76535), and the station 6 boulder samples. Most of the boulder samples have been studied in Consortium mode, and many of the rake samples have received a basic petrological/geochemical characterization.

F-16XL ship #1 CAWAP flight - alpha 5 degrees, altitude 10,000 feet

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. This photo shows the aircraft gathering data at an altitude of 10,000 feet, with an angle of attack of 5 degrees. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

F-16XL ship #1 CAWAP flight

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

F-16XL ship #1 wing close-up showing boundary layer detection Preston tubes

NASA Technical Reports Server (NTRS)

1995-01-01

This photo shows the boundary layer Preston tubes mounted on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

Bonnie Takes Aim at an Oily Gulf

NASA Image and Video Library

2010-07-24

Tropical Storm Bonnie, now a depression, rakes South Florida in this infrared image from NASA Atmospheric Infrared Sounder , en route to a weekend run-in with the Gulf of Mexico and the Gulf oil spill.

In-flight comparisons of boundary-layer and wake measurement probes for incompressible flow

NASA Technical Reports Server (NTRS)

Mertaugh, L. J., Jr.

1972-01-01

The results are presented of in-flight comparisons of a number of boundary-layer and wake measurement probes suitable for low-speed flight-test investigations. The tested boundary-layer probes included a traversing total-pressure probe and a hot-film probe mounted on an internally-mounted drive mechanism, a curved and a straight boundary-layer rake, and a traversing hot-film probe with an externally-mounted drive mechanism. The wake measuring devices included a traversing, self-aligning probe, a wake rake, and an integrating wake rate. The boundary-layer data are compared with a common reference velocity profile and comments given regarding the accuracy of the static-pressure and total-pressure measurements. Discussions on the various calibration presentations used with hot-wire and hot-film sensors and various aspects of improving the accuracy of hot-film sensor results are given in the appendix of this report.

Probabilistic Analysis and Design of a Raked Wing Tip for a Commercial Transport

NASA Technical Reports Server (NTRS)

Mason Brian H.; Chen, Tzi-Kang; Padula, Sharon L.; Ransom, Jonathan B.; Stroud, W. Jefferson

2008-01-01

An approach for conducting reliability-based design and optimization (RBDO) of a Boeing 767 raked wing tip (RWT) is presented. The goal is to evaluate the benefits of RBDO for design of an aircraft substructure. A finite-element (FE) model that includes eight critical static load cases is used to evaluate the response of the wing tip. Thirteen design variables that describe the thickness of the composite skins and stiffeners are selected to minimize the weight of the wing tip. A strain-based margin of safety is used to evaluate the performance of the structure. The randomness in the load scale factor and in the strain limits is considered. Of the 13 variables, the wing-tip design was controlled primarily by the thickness of the thickest plies in the upper skins. The report includes an analysis of the optimization results and recommendations for future reliability-based studies.

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake

NASA Astrophysics Data System (ADS)

Heidelberg, Laurence J.; Hall, David G.

1993-01-01

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.

Acoustic Mode Measurements in the Inlet of a Model Turbofan Using a Continuously Rotating Rake

NASA Technical Reports Server (NTRS)

Heidelberg, Laurence J.; Hall, David G.

1992-01-01

Comprehensive measurements of the spinning acoustic mode structure in the inlet of the Advanced Ducted Propeller (ADP) have been completed. These measurements were taken using a unique and previously untried method which was first proposed by T.G. Sofrin. A continuously rotating microphone system was employed. The ADP model was designed and built by Pratt & Whitney and tested in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Three inlet configurations were tested with cut-on and cutoff stator vane sets. The cutoff stator was designed to suppress all modes at the blade passing frequency. Rotating rake measurements indicate that several extraneous circumferential modes were active. The mode orders suggest that their source was an interaction between the rotor and small interruptions in the casing tip treatment. The cut-on stator produced the expected circumferential modes plus higher levels of the unexpected modes seen with the cutoff stator.

On the closed form mechanistic modeling of milling: Specific cutting energy, torque, and power

NASA Astrophysics Data System (ADS)

Bayoumi, A. E.; Yücesan, G.; Hutton, D. V.

1994-02-01

Specific energy in metal cutting, defined as the energy expended in removing a unit volume of workpiece material, is formulated and determined using a previously developed closed form mechanistic force model for milling operations. Cutting power is computed from the cutting torque, cutting force, kinematics of the cutter, and the volumetric material removal rate. Closed form expressions for specific cutting energy were formulated and found to be functions of the process parameters: pressure and friction for both rake and flank surfaces and chip flow angle at the rake face of the tool. Friction is found to play a very important role in cutting torque and power. Experiments were carried out to determine the effects of feedrate, cutting speed, workpiece material, and flank wear land width on specific cutting energy. It was found that the specific cutting energy increases with a decrease in the chip thickness and with an increase in flank wear land.

Test data from small solid propellant rocket motor plume measurements (FA-21)

NASA Technical Reports Server (NTRS)

Hair, L. M.; Somers, R. E.

1976-01-01

A program is described for obtaining a reliable, parametric set of measurements in the exhaust plumes of solid propellant rocket motors. Plume measurements included pressures, temperatures, forces, heat transfer rates, particle sampling, and high-speed movies. Approximately 210,000 digital data points and 15,000 movie frames were acquired. Measurements were made at points in the plumes via rake-mounted probes, and on the surface of a large plate impinged by the exhaust plume. Parametric variations were made in pressure altitude, propellant aluminum loading, impinged plate incidence angle and distance from nozzle exit to plate or rake. Reliability was incorporated by continual use of repeat runs. The test setup of the various hardware items is described along with an account of test procedures. Test results and data accuracy are discussed. Format of the data presentation is detailed. Complete data are included in the appendix.

Impact of Collection Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

DOE Office of Scientific and Technical Information (OSTI.GOV)

William Smith; Jeffery Einerson; Kevin Kenney

2014-09-01

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment testedmore » included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg-1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.« less

Promoting species establishment in a phragmites-dominated great lakes coastal wetland

USGS Publications Warehouse

Carlson, M.L.; Kowalski, K.P.; Wilcox, D.A.

2009-01-01

This study examined efforts to promote species establishment and maintain diversity in a Phragmites-dominated wetland where primary control measures were underway. A treatment experiment was performed at Crane Creek, a drowned-river-mouth wetland in Ottawa National Wildlife Refuge along the shore of western Lake Erie. Following initial aerial spraying of Phragmites with glyphosate, this study tested combinations of cutting, raking, and additional hand spraying of Phragmites with glyphosate as methods to promote growth of other wetland species and increase plant diversity. Percent-cover vegetation data were collected in permanent plots before and after treatments, and follow-up sampling was performed the following year. Increased species richness, species emergence, and relative dominance of non-Phragmites taxa were used as measures of treatment success. We also examined treatment effects on Phragmites cover. Dimensionality of seedbank and soil properties was reduced using principal component analysis. With the exception of nitrogen, soil nutrients affected species establishment, non-Phragmites taxa dominance, and Phragmites cover. A more viable seedbank led to greater species emergence. Treatments had differential effects on diversity depending on elevation and resulting degree of hydrologic inundation. Whereas raking to remove dead Phragmites biomass was central to promoting species establishment in dry areas, spraying had a greater impact in continually inundated areas. For treatment success across elevations into the year following treatments, spraying in combination with cutting and raking had the greatest effect. The results of this study suggest that secondary treatments can produce a short-term benefit to the plant community in areas treated for Phragmites.

Crashworthiness analysis of the January 26, 2005 Glendale, California rail collision

DOT National Transportation Integrated Search

2011-03-16

In Glendale, California on January 26, 2005, impact with : an SUV on the track caused a southbound commuter train to : derail, impact a standing freight train, buckle laterally outward, : and rake the side of a northbound commuter train. Significant ...

Effects of fault dip and slip rake angles on near-source ground motions: Why rupture directivity was minimal in the 1999 Chi-Chi, Taiwan, earthquake

USGS Publications Warehouse

Aagaard, Brad T.; Hall, J.F.; Heaton, T.H.

2004-01-01

We study how the fault dip and slip rake angles affect near-source ground velocities and displacements as faulting transitions from strike-slip motion on a vertical fault to thrust motion on a shallow-dipping fault. Ground motions are computed for five fault geometries with different combinations of fault dip and rake angles and common values for the fault area and the average slip. The nature of the shear-wave directivity is the key factor in determining the size and distribution of the peak velocities and displacements. Strong shear-wave directivity requires that (1) the observer is located in the direction of rupture propagation and (2) the rupture propagates parallel to the direction of the fault slip vector. We show that predominantly along-strike rupture of a thrust fault (geometry similar in the Chi-Chi earthquake) minimizes the area subjected to large-amplitude velocity pulses associated with rupture directivity, because the rupture propagates perpendicular to the slip vector; that is, the rupture propagates in the direction of a node in the shear-wave radiation pattern. In our simulations with a shallow hypocenter, the maximum peak-to-peak horizontal velocities exceed 1.5 m/sec over an area of only 200 km2 for the 30??-dipping fault (geometry similar to the Chi-Chi earthquake), whereas for the 60??- and 75??-dipping faults this velocity is exceeded over an area of 2700 km2 . These simulations indicate that the area subjected to large-amplitude long-period ground motions would be larger for events of the same size as Chi-Chi that have different styles of faulting or a deeper hypocenter.

Sugarcane cultural practices to increase profits

USDA-ARS?s Scientific Manuscript database

Multiple experiments were initiated in an effort to reduce costs, increase ratooning, and maximize profits. A new method of mechanical removal using a modified rake produced yields similarly to burning, with both yielding an additional 1000 lbs/A than full retention. Where burning was not an option,...

Big Jobs: Planning for Competence

ERIC Educational Resources Information Center

Jones, Nancy P.

2005-01-01

Three- to five-year-olds grow emotionally participating in meaningful and challenging physical, social, and problem-solving activities outdoors in an early childhood program on a farm. Caring for animals, planting, raking, shoveling, and engaging in meaningful indoor activities, under adult supervision, children learn to work collaboratively,…

Investigating the effects of PDC cutters geometry on ROP using the Taguchi technique

NASA Astrophysics Data System (ADS)

Jamaludin, A. A.; Mehat, N. M.; Kamaruddin, S.

2017-10-01

At times, the polycrystalline diamond compact (PDC) bit’s performance dropped and affects the rate of penetration (ROP). The objective of this project is to investigate the effect of PDC cutter geometry and optimize them. An intensive study in cutter geometry would further enhance the ROP performance. The relatively extended analysis was carried out and four significant geometry factors have been identified that directly improved the ROP. Cutter size, back rake angle, side rake angle and chamfer angle are the stated geometry factors. An appropriate optimization technique that effectively controls all influential geometry factors during cutters manufacturing is introduced and adopted in this project. By adopting L9 Taguchi OA, simulation experiment is conducted by using explicit dynamics finite element analysis. Through a structure Taguchi analysis, ANOVA confirms that the most significant geometry to improve ROP is cutter size (99.16% percentage contribution). The optimized cutter is expected to drill with high ROP that can reduce the rig time, which in its turn, may reduce the total drilling cost.

The effects of floor incline on lower extremity biomechanics during unilateral landing from a jump in dancers.

PubMed

Pappas, Evangelos; Orishimo, Karl F; Kremenic, Ian; Liederbach, Marijeanne; Hagins, Marshall

2012-05-01

Retrospective studies have suggested that dancers performing on inclined ("raked") stages have increased injury risk. One study suggests that biomechanical differences exist between flat and inclined surfaces during bilateral landings; however, no studies have examined whether such differences exist during unilateral landings. In addition, little is known regarding potential gender differences in landing mechanics of dancers. Professional dancers (N = 41; 14 male, 27 female) performed unilateral drop jumps from a 30 cm platform onto flat and inclined surfaces while extremity joint angles and moments were identified and analyzed. There were significant joint angle and moment effects due to the inclined flooring. Women had significantly decreased peak ankle dorsiflexion and hip adduction moment compared with men. Findings of the current study suggest that unilateral landings on inclined stages create measurable changes in lower extremity biomechanical variables. These findings provide a preliminary biomechanical rationale for differences in injury rates found in observational studies of raked stages.

Effects of Distortion on Mass Flow Plug Calibration

NASA Technical Reports Server (NTRS)

Sasson, Jonathan; Davis, David O.; Barnhart, Paul J.

2015-01-01

A numerical, and experimental investigation to study the effects of flow distortion on a Mass Flow Plug (MFP) used to control and measure mass-flow during an inlet test has been conducted. The MFP was first calibrated using the WIND-US flow solver for uniform (undistorted) inflow conditions. These results are shown to compare favorably with an experimental calibration under similar conditions. The effects of distortion were investigated by imposing distorted flow conditions taken from an actual inlet test to the inflow plane of the numerical simulation. The computational fluid dynamic (CFD) based distortion study only showed the general trend in mass flow rate. The study used only total pressure as the upstream boundary condition, which was not enough to define the flow. A better simulation requires knowledge of the turbulence structure and a specific distortion pattern over a range of plug positions. It is recommended that future distortion studies utilize a rake with at least the same amount of pitot tubes as the AIP rake.

The generation of tire cornering forces in aircraft with a free-swiveling nose gear

NASA Technical Reports Server (NTRS)

Daugherty, R. H.; Stubbs, S. M.

1985-01-01

An experimental investigation was conducted to study the effect of various parameters on the cornering forces produced by a rolling aircraft tire installed on a tilted, free-swiveling nose gear. The parameters studied included tilt angle, trial, tire inflation pressure, rake angle, vertical load, and whether or not a twin tire configuration corotates. These parameters were evaluated by measuring the cornering force produced by an aircraft tire installed on the nose gear of a modified vehicle as it was towed slowly. Cornering force coefficient increased with increasing tilt angle. Increasing trial or rake angle decreased the magnitude of the cornering force coefficient. Tire inflation pressure had no effect on the cornering force coefficient. Increasing vertical load decreased the cornering force coefficient. When the tires of a twin tire system rotated independently, the cornering force coefficients were the same as those for the single-tire configuration. When the twin tire system was made to corotate, however, the cornering force coefficients increased significantly.

16-foot transonic tunnel test section flowfield survey

NASA Technical Reports Server (NTRS)

Yetter, J. A.; Abeyounis, W. K.

1994-01-01

A flow survey has been made of the test section of the NASA Langley Research Center 16-Foot Transonic Tunnel at subsonic and supersonic speeds. The survey was performed using five five-hole pyramid-head probes mounted at 14 inch intervals on a survey rake. Probes were calibrated at freestream Mach numbers from 0.50 to 0.95 and from 1.18 to 1.23. Flowfield surveys were made at Mach numbers from 0.50 to 0.90 and at Mach 1.20. The surveys were made at tunnel stations 130.6, 133.6, and 136.0. By rotating the survey rake through 180 degrees, a cylindrical volume of the test section 4.7 feet in diameter and 5.4 feet long centered about the tunnel centerline was surveyed. Survey results showing the measured test section upflow and sideflow characteristics and local Mach number distributions are presented. The report documents the survey probe calibration techniques used, summarizes the procedural problems encountered during testing, and identifies the data discrepancies observed during the post-test data analysis.

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake: Data collection/analysis techniques

NASA Technical Reports Server (NTRS)

Hall, David G.; Heidelberg, Laurence; Konno, Kevin

1993-01-01

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.

Acoustic mode measurements in the inlet of a model turbofan using a continuously rotating rake - Data collection/analysis techniques

NASA Technical Reports Server (NTRS)

Hall, David G.; Heidelberg, Laurence; Konno, Kevin

1993-01-01

The rotating microphone measurement technique and data analysis procedures are documented which are used to determine circumferential and radial acoustic mode content in the inlet of the Advanced Ducted Propeller (ADP) model. Circumferential acoustic mode levels were measured at a series of radial locations using the Doppler frequency shift produced by a rotating inlet microphone probe. Radial mode content was then computed using a least squares curve fit with the measured radial distribution for each circumferential mode. The rotating microphone technique is superior to fixed-probe techniques because it results in minimal interference with the acoustic modes generated by rotor-stator interaction. This effort represents the first experimental implementation of a measuring technique developed by T. G. Sofrin. Testing was performed in the NASA Lewis Low Speed Anechoic Wind Tunnel at a simulated takeoff condition of Mach 0.2. The design is included of the data analysis software and the performance of the rotating rake apparatus. The effect of experiment errors is also discussed.

Moment-tensor solutions for the 24 November 1987 Superstition Hills, California, earthquakes

USGS Publications Warehouse

Sipkin, S.A.

1989-01-01

The teleseismic long-period waveforms recorded by the Global Digital Seismograph Network from the two largest Superstition Hills earthquakes are inverted using an algorithm based on optimal filter theory. These solutions differ slightly from those published in the Preliminary Determination of Epicenters Monthly Listing because a somewhat different, improved data set was used in the inversions and a time-dependent moment-tensor algorithm was used to investigate the complexity of the main shock. The foreshock (origin time 01:54:14.5, mb 5.7, Ms6.2) had a scalar moment of 2.3 ?? 1025 dyne-cm, a depth of 8km, and a mechanism of strike 217??, dip 79??, rake 4??. The main shock (origin time 13:15:56.4, mb 6.0, Ms6.6) was a complex event, consisting of at least two subevents, with a combined scalar moment of 1.0 ?? 1026 dyne-cm, a depth of 10km, and a mechanism of strike 303??, dip 89??, rake -180??. -Authors

A study of the cornering forces generated by aircraft tires on a tilted, free-swiveling nose gear

NASA Technical Reports Server (NTRS)

Daugherty, R. H.; Stubbs, S. M.

1985-01-01

An experimental investigation was conducted to study the effect of various parameters on the cornering forces produced by a rolling aircraft tire installed on a tilted, free-swiveling nose gear. The parameters studied included tilt angle, trial, tire inflation pressure, rake angle, vertical load, and whether or not a twin tire configuration corotates. These parameters were evaluated by measuring the cornering force produced by an aircraft tire installed on the nose gear of a modified vehicle as it was towed slowly. Cornering force coefficient increased with increasing tilt angle. Increasing trial or rake angle decreased the magnitude of the cornering force coefficient. Tire inflation pressure had no effect on the cornering force coefficient. Increasing vertical load decreased the cornering force coefficient. When the tires of a twin tire system rotated independently, the cornering force coefficients were the same as those for the single-tire configuration. When the twin tire system was made to corotate, however, the cornering force coefficients increased significantly.

F-16XL ship #1 - CAWAP boundary layer hot film, left wing

NASA Technical Reports Server (NTRS)

1996-01-01

This photo shows the boundary layer hot film on the left wing of NASA's single-seat F-16XL (ship #1) used for the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. Hot film is used to measure temperature changes on a surface. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

F-16XL ship #1 CAWAP flight - alpha 15 degrees, altitude 5,000 feet

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. This photo shows the aircraft gathering data at an altitude of 5000 feet, with an angle of attack of 15 degrees. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

9 CFR 3.1 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... Hard surfaces with which the dogs or cats come in contact must be spot-cleaned daily and sanitized in... spot-cleaned with sufficient frequency to ensure all animals the freedom to avoid contact with excreta. Contaminated material must be replaced whenever this raking and spot-cleaning is not sufficient to prevent or...

Faculty Workload: An Analytical Approach

ERIC Educational Resources Information Center

Dennison, George M.

2012-01-01

Recent discussions of practices in higher education have tended toward muck-raking and self-styled exposure of cynical self-indulgence by faculty and administrators at the expense of students and their families, as usually occurs during periods of economic duress, rather than toward analytical studies designed to foster understanding This article…

Exploring Online Graduate Students' Responses to Online Self-Regulation Training

ERIC Educational Resources Information Center

Dunn, Karee E.; Rakes, Glenda C.

2015-01-01

In this study, online graduate students participated in four brief online self-regulatory trainings for self-efficacy, achievement goal orientation, learning strategies, and attributional thinking. These variables are critical to success in learning environments, but perhaps even more so in the online academic environment (Rakes, Dunn, &…

An Earthquake Source Sensitivity Analysis for Tsunami Propagation in the Eastern Mediterranean

NASA Astrophysics Data System (ADS)

Necmioglu, Ocal; Meral Ozel, Nurcan

2013-04-01

An earthquake source parameter sensitivity analysis for tsunami propagation in the Eastern Mediterranean has been performed based on 8 August 1303 Crete and Dodecanese Islands earthquake resulting in destructive inundation in the Eastern Mediterranean. The analysis involves 23 cases describing different sets of strike, dip, rake and focal depth, while keeping the fault area and displacement, thus the magnitude, same. The main conclusions of the evaluation are drawn from the investigation of the wave height distributions at Tsunami Forecast Points (TFP). The earthquake vs. initial tsunami source parameters comparison indicated that the maximum initial wave height values correspond in general to the changes in rake angle. No clear depth dependency is observed within the depth range considered and no strike angle dependency is observed in terms of amplitude change. Directivity sensitivity analysis indicated that for the same strike and dip, 180° shift in rake may lead to 20% change in the calculated tsunami wave height. Moreover, an approximately 10 min difference in the arrival time of the initial wave has been observed. These differences are, however, greatly reduced in the far field. The dip sensitivity analysis, performed separately for thrust and normal faulting, has both indicated that an increase in the dip angle results in the decrease of the tsunami wave amplitude in the near field approximately 40%. While a positive phase shift is observed, the period and the shape of the initial wave stays nearly the same for all dip angles at respective TFPs. These affects are, however, not observed at the far field. The resolution of the bathymetry, on the other hand, is a limiting factor for further evaluation. Four different cases were considered for the depth sensitivity indicating that within the depth ranges considered (15-60 km), the increase of the depth has only a smoothing effect on the synthetic tsunami wave height measurements at the selected TFPs. The strike sensitivity analysis showed clear phase shift with respect to the variation of the strike angles, without leading to severe variation of the initial and maximum waves at locations considered. Travel time maps for two cases corresponding to difference in the strike value (60° vs 150°) presented a more complex wave propagation for the case with 60° strike angle due to the fact that the normal of the fault plane is orthogonal to the main bathymetric structure in the region, namely the Eastern section of the Hellenic Arc between Crete and Rhodes Islands. For a given set of strike, dip and focal depth parameters, the effect of the variation in the rake angle has been evaluated in the rake sensitivity analysis. A waveform envelope composed of symmetric synthetic recordings at one TFPs could be clearly observed as a result of rake angle variations in 0-180° range. This could also lead to the conclusion that for a given magnitude (fault size and displacement), the expected maximum and minimum tsunami wave amplitudes could be evaluated as a waveform envelope rather limited to a single point of time or amplitude. The Evaluation of the initial wave arrival times follows an expected pattern controlled by the distance, wheras maximum wave arrival time distribution presents no clear pattern. Nevertheless, the distribution is rather concentrated in time domain for some TFPs. Maximum positive and minimum negative wave amplitude distributions indicates a broader range for a subgroup of TFPs, wheras for the remaining TFPs the distributions are narrow. Any deviation from the expected trend of calculating narrower ranges of amplitude distributions could be interpreted as the result o the bathymetry and focusing effects. As similar studies conducted in the different parts of the globe indicated, the main characteristics of the tsunami propagation are unique for each basin. It should be noted, however, that the synthetic measurements obtained at the TFPs in the absence of high-resolution bathymetric data, should be considered only an overall guidance. The results indicate the importance of the accuracy of earthquake source parameters for reliable tsunami predictions and the need for high-resolution bathymetric data to be able to perform calculations with higher accuracy. On the other hand, this study did not address other parameters, such as heterogeneous slip distribution and rupture duration, which affect the tsunami initiation and propagation process.

"Language Must Be Raked": Experience, Race, and the Pressure of Air

ERIC Educational Resources Information Center

Standish, Paul

2018-01-01

This article begins by clarifying the notion of what Stanley Cavell has called "Emersonian moral perfectionism." It goes on to explore this through close analysis of aspects of Emerson's essay "Experience," in which ideas of trying or attempting or experimenting bring out the intimate relation between perfectionism and styles…

46 CFR 32.63-20 - Hull structure-B/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... condition such that the forward rake bulkhead rests upon a pinnacle at the water surface, the maximum hull bending stress shall not exceed the following limits: (1) Independent tanks may be installed in such a... stress shall not exceed either 50 percent of the minimum ultimate tensile strength of the material or 70...

12. CLOSEUP OF THE CURRENT TRASH RAKELIFTING MECHANISM (CALLED 'JAWS' ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. CLOSE-UP OF THE CURRENT TRASH RAKE-LIFTING MECHANISM (CALLED 'JAWS' BY THE PRESENT OPERATORS), LOOKING WEST. THIS EQUIPMENT WAS REMOVED IN AUTUMN OF 1996. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

Landscape in a Lacquer Box

ERIC Educational Resources Information Center

Savage, Martha

2010-01-01

A symbolic dry landscape garden of Eastern origin holds a special fascination for the author's middle-school students, which is why the author chose to create a project exploring this view of nature. A dry landscape garden, or "karesansui," is an arrangement of rocks, worn by nature and surrounded by a "sea" of sand, raked into patterns…

EFFECTS OF RECREATIONAL CLAM HARVESTING ON EELGRASS (ZOSTERA MARINA) AND ASSOCIATED INFAUNAL INVERTEBRATES: IN SITU MANIPULATIVE EXPERIMENTS

EPA Science Inventory

The effect of recreational clam harvesting on eelgrass (Zostera marina) was experimentally tested by raking or digging for clams in experimental 1-m2 plots located in a Yaquina Bay (Newport, OR) eelgrass meadow. After three monthly treatments, eelgrass measures of biomass, prima...

Performance Calculations for a Boundary-Layer-Ingesting Fan Stage from Sparse Measurements

NASA Technical Reports Server (NTRS)

Hirt, Stefanie M.; Wolter, John D.; Arend, David J.; Hearn, Tristan A.; Hardin, Larry W.; Gazzaniga, John A.

2018-01-01

A test of the Boundary Layer Ingesting-Inlet / Distortion-Tolerant Fan was completed in NASA Glenn's 8-Foot by 6-Foot supersonic wind tunnel. Inlet and fan performance were measured by surveys using a set of rotating rake arrays upstream and downstream of the fan stage. Surveys were conducted along the 100 percent speed line and a constant exit corrected flow line passing through the aerodynamic design point. These surveys represented only a small fraction of the data collected during the test. For other operating points, data was recorded as snapshots without rotating the rakes which resulted in a sparser set of recorded data. This paper will discuss analysis of these additional, lower measurement density data points to expand our coverage of the fan map. Several techniques will be used to supplement the snapshot data at test conditions where survey data also exists. The supplemented snapshot data will be compared with survey results to assess the quality of the approach. Effective methods will be used to analyze the data set for which only snapshots exist.

Effects of land clearing techniques and tillage systems on runoff and soil erosion in a tropical rain forest in Nigeria.

PubMed

Ehigiator, O A; Anyata, B U

2011-11-01

This work reports runoff and soil loss from each of 14 sub-watersheds in a secondary rain forest in south-western Nigeria. The impact of methods of land clearing and post-clearing management on runoff and soil erosion under the secondary forest is evaluated. These data were acquired eighteen years after the deforestation of primary vegetation during the ' West bank' project of the International Institute for Tropical Agriculture (IITA). These data are presented separately for each season; however, statistical analyses for replicates were not conducted due to differences in their past management. Soil erosion was affected by land clearing and tillage methods. The maximum soil erosion was observed on sub-watersheds that were mechanically cleared with tree-pusher/root-rake attachments and tilled conventionally. A high rate of erosion was observed even when graded-channel terraces were constructed to minimize soil erosion. In general there was much less soil erosion on manually cleared than on mechanically cleared sub-watersheds (2.5 t ha(-1) yr(-1) versus 13.8 t ha(-1) yr(-1)) and from the application of no-tillage methods than from conventionally plowed areas (6.5 t ha(-1) yr(-1) versus 12.1 t ha(-1) yr(-1)). The data indicate that tillage methods and appropriate management of soils and crops play an important role in soil and water conservation and in decreasing the rate of decline of soil quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

11. VIEW SHOWING THE SUPERSTRUCTURE OF THE SHED ROOF (REMOVED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. VIEW SHOWING THE SUPERSTRUCTURE OF THE SHED ROOF (REMOVED AUTUMN OF 1996) PROTECTING THE PRESENT INTAKE GATES- AND RAKE-LIFTING MECHANISMS AND THE TRASH RACKS (LOWER FOREGROUND), LOOKING NORTH. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

Behind the Scenes: Understanding Teacher Perspectives on Technology Integration in a Suburban District Technology Initiative

ERIC Educational Resources Information Center

Woolard, John

2012-01-01

Efforts to prepare students with skills necessary to compete in a 21st Century global, digital economy require technological literacy, but many teachers are inhibited by antiquated models of education and epistemological beliefs that leave them reluctant to integrate educational technologies in their content instruction (Dunn & Rakes, 2010;…

F-16XL ship #1 CAWAP flight - alpha 10 degrees, beta -5 degrees, altitude 10,000 feet

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. This photo shows the aircraft gathering data at an altitude of 10,000 feet, with an angle of attack of 10 degrees and a sideslip angle of -5 degrees. The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

F-16XL ship #1 crew

NASA Technical Reports Server (NTRS)

1995-01-01

November 27, 1995 Photograph of the F-16XL Ship #1 Cranked-Arrow Wing Aerodynamic Project (CAWAP) Test Team; from left to right, Ron Wilcox; Operations Engineer, Art Cope; Aircraft Mechanic, Dave Fisher; Chief Project Engineer, Dick Denman; Aircraft Mechanic, Bob Garcia; A/C Crew Chief, Susan Ligon; Aircraft Mechanic, Rodger Tarango; Mobile Operations Facility (MOF) Staff, Jerry Cousins; Aircraft Mechanic, Bruce Gallmeyer; MOF Staff, and Mike Reardon; Aircraft Mechanic/Helper. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. The first flight of CAWAP occurred at NASA's Dryden Flight Research Center, Edwards, California, on November 21, 1995, and the test program ended in April 1996.

F-16XL ship #1 CAWAP flight - alpha 21 degrees, altitude 17,500 feet

NASA Technical Reports Server (NTRS)

1996-01-01

The single-seat F-16XL (ship #1) makes another run during the Cranked-Arrow Wing Aerodynamic Project (CAWAP) at Dryden Flight Research Center, Edwards, California. The modified airplane features a delta 'cranked-arrow' wing with strips of tubing along the leading edge to the trailing edge to sense static on the wing and obtain pressure distribution data. The right wing receives data on pressure distribution and the left wing (visible here) has three types of instrumentation - preston tubes to measure local skin friction, boundary layer rakes to measure boundary layer profiles (the layer where the air interacts with the surfaces of a moving aircraft), and hot films to determine boundary layer transition locations. This photo shows the aircraft gathering data at an altitude of 17,500 feet, with an angle of attack of 21 degrees The program also gathered aero data on two wing planforms for NASA's High Speed Research Program. The first flight of CAWAP occurred on November 21, 1995, and the test program ended in April 1996.

A comparative Thermal Analysis of conventional parabolic receiver tube and Cavity model tube in a Solar Parabolic Concentrator

NASA Astrophysics Data System (ADS)

Arumugam, S.; Ramakrishna, P.; Sangavi, S.

2018-02-01

Improvements in heating technology with solar energy is gaining focus, especially solar parabolic collectors. Solar heating in conventional parabolic collectors is done with the help of radiation concentration on receiver tubes. Conventional receiver tubes are open to atmosphere and loose heat by ambient air currents. In order to reduce the convection losses and also to improve the aperture area, we designed a tube with cavity. This study is a comparative performance behaviour of conventional tube and cavity model tube. The performance formulae were derived for the cavity model based on conventional model. Reduction in overall heat loss coefficient was observed for cavity model, though collector heat removal factor and collector efficiency were nearly same for both models. Improvement in efficiency was also observed in the cavity model’s performance. The approach towards the design of a cavity model tube as the receiver tube in solar parabolic collectors gave improved results and proved as a good consideration.

Intensive Hemodialysis Associates with Improved Survival Compared with Conventional Hemodialysis

PubMed Central

Lindsay, Robert M.; Cuerden, Meaghan S.; Garg, Amit X.; Port, Friedrich; Austin, Peter C.; Moist, Louise M.; Pierratos, Andreas; Chan, Christopher T.; Zimmerman, Deborah; Lockridge, Robert S.; Couchoud, Cécile; Chazot, Charles; Ofsthun, Norma; Levin, Adeera; Copland, Michael; Courtney, Mark; Steele, Andrew; McFarlane, Philip A.; Geary, Denis F.; Pauly, Robert P.; Komenda, Paul; Suri, Rita S.

2012-01-01

Patients undergoing conventional maintenance hemodialysis typically receive three sessions per week, each lasting 2.5–5.5 hours. Recently, the use of more intensive hemodialysis (>5.5 hours, three to seven times per week) has increased, but the effects of these regimens on survival are uncertain. We conducted a retrospective cohort study to examine whether intensive hemodialysis associates with better survival than conventional hemodialysis. We identified 420 patients in the International Quotidian Dialysis Registry who received intensive home hemodialysis in France, the United States, and Canada between January 2000 and August 2010. We matched 338 of these patients to 1388 patients in the Dialysis Outcomes and Practice Patterns Study who received in-center conventional hemodialysis during the same time period by country, ESRD duration, and propensity score. The intensive hemodialysis group received a mean (SD) 4.8 (1.1) sessions per week with a mean treatment time of 7.4 (0.87) hours per session; the conventional group received three sessions per week with a mean treatment time of 3.9 (0.32) hours per session. During 3008 patient-years of follow-up, 45 (13%) of 338 patients receiving intensive hemodialysis died compared with 293 (21%) of 1388 patients receiving conventional hemodialysis (6.1 versus 10.5 deaths per 100 person-years; hazard ratio, 0.55 [95% confidence interval, 0.34–0.87]). The strength and direction of the observed association between intensive hemodialysis and improved survival were consistent across all prespecified subgroups and sensitivity analyses. In conclusion, there is a strong association between intensive home hemodialysis and improved survival, but whether this relationship is causal remains unknown. PMID:22362910

Developing a Data Set and Processing Methodology for Fluid/Structure Interaction Code Validation

DTIC Science & Technology

2007-06-01

50 29. 9-Probe Wake Survey Rake Configurations...structural stability and fatigue in test article components and, in general, in facility support structures and rotating machinery blading . Both T&E... blade analysis and simulations. To ensure the accuracy of the U of CO technology, validation using flight-test data and test data from a wind tunnel

Impacts of switchgrass intercropping in traditional pine forests on hydrology and water quality in the southeastern United States.

Treesearch

Devendra Amatya; G.M. Chescheir; J.E. Nettles

2016-01-01

Preliminary results indicate that switchgrass (Panicum virgatum L.), grown as a cellulosic biofuel between managed loblolly pine (Pinus taeda L.) beds on the Atlantic Coastal Plain forests has no significant effect on shallow ground water table and stream outflows. Although management operations (e.g. harvesting, shearing between pine rows, raking, and bedding)...

Project CHECO Southeast Asia Report. Operation DELAWARE 19 April - 17 May 1968

DTIC Science & Technology

1968-09-02

artillery delivered to LZs PEPPER and GOODMANT󈧸/ 25 (D+6) 3d Bde, 1st Cav Div, air-assaulted into LZ STALLION (A Luoi Airfield), 53/ Three 37-mm AAA guns...cases) 500 Beef bouillon qts) 10 Preserves (cases) 11 Pork and beef CHICOM) (qts) 1,125 MISCELLANEOUS ITEMS Barbed wire (rolls) 30 Pick, shovels, rakes

2. CLOSEUP OF SOUTH FACADE OF UPPER FALLS GATE HOUSE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. CLOSEUP OF SOUTH FACADE OF UPPER FALLS GATE HOUSE, SHOWING TRASH RACKS, REMOVABLE STEEL DOORS, TRASH RAKE STRUCTURE, AND DERRICK, WINCH AND CABLE GATE LIFTING DEVICE, LOOKING SOUTH/SOUTHWEST. - Washington Water Power Spokane River Upper Falls Hydroelectric Development, Gate House, Spokane River, approximately 0.5 mile northeast of intersection of Spokane Falls Boulevard & Post Street, Spokane, Spokane County, WA

Reliability Based Design for a Raked Wing Tip of an Airframe

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Coroneos, Rula M.

2011-01-01

A reliability-based optimization methodology has been developed to design the raked wing tip of the Boeing 767-400 extended range airliner made of composite and metallic materials. Design is formulated for an accepted level of risk or reliability. The design variables, weight and the constraints became functions of reliability. Uncertainties in the load, strength and the material properties, as well as the design variables, were modeled as random parameters with specified distributions, like normal, Weibull or Gumbel functions. The objective function and constraint, or a failure mode, became derived functions of the risk-level. Solution to the problem produced the optimum design with weight, variables and constraints as a function of the risk-level. Optimum weight versus reliability traced out an inverted-S shaped graph. The center of the graph corresponded to a 50 percent probability of success, or one failure in two samples. Under some assumptions, this design would be quite close to the deterministic optimum solution. The weight increased when reliability exceeded 50 percent, and decreased when the reliability was compromised. A design could be selected depending on the level of risk acceptable to a situation. The optimization process achieved up to a 20-percent reduction in weight over traditional design.

Numerical Technique for Analyzing Rotating Rake Mode Measurements in a Duct With Passive Treatment and Shear Flow

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Sutliff, Daniel L.

2007-01-01

A technique is presented for the analysis of measured data obtained from a rotating microphone rake system. The system is designed to measure the interaction modes of ducted fans. A Fourier analysis of the data from the rotating system results in a set of circumferential mode levels at each radial location of a microphone inside the duct. Radial basis functions are then least-squares fit to this data to obtain the radial mode amplitudes. For ducts with soft walls and mean flow, the radial basis functions must be numerically computed. The linear companion matrix method is used to obtain both the eigenvalues of interest, without an initial guess, and the radial basis functions. The governing equations allow for the mean flow to have a boundary layer at the wall. In addition, a nonlinear least-squares method is used to adjust the wall impedance to best fit the data in an attempt to use the rotating system as an in-duct wall impedance measurement tool. Simulated and measured data are used to show the effects of wall impedance and mean flow on the computed results.

Investigating bone chip formation in craniotomy.

PubMed

Huiyu, He; Chengyong, Wang; Yue, Zhang; Yanbin, Zheng; Linlin, Xu; Guoneng, Xie; Danna, Zhao; Bin, Chen; Haoan, Chen

2017-10-01

In a craniotomy, the milling cutter is one of the most important cutting tools. The operating performance, tool durability and cutting damage to patients are influenced by the tool's sharpness, intensity and structure, whereas the cutting characteristics rely on interactions between the tool and the skull. In this study, an orthogonal cutting experiment during a craniotomy of fresh pig skulls was performed to investigate chip formation on the side cutting and face cutting of the skull using a high-speed camera. The cutting forces with different combinations of cutting parameters, such as the rake angle, clearance angle, depth of cut and cutting speed, were measured. The skull bone microstructure and cutting damage were observed by scanning electron microscope. Cutting models for different cutting approaches and various depths of cut were constructed and analyzed. The study demonstrated that the effects of shearing, tension and extrusion occur during chip formation. Various chip types, such as unit chips, splintering chips and continuous chips, were generated. Continuous pieces of chips, which are advisable for easy removal from the field of operation, were formed at greater depths of cut and tool rake angles greater than 10°. Cutting damage could be relieved with a faster recovery with clearance angles greater than 20°.

Determination Hypocentre and Focal Mechanism Earthquake of Oct 31, 2016 in Bone, South Sulawesi

NASA Astrophysics Data System (ADS)

Altin Massinai, Muhammad; Fawzy Ismullah M, Muhammad

2018-03-01

Indonesian Meteorology, Climatology and Geophysics Agency (BMKG) recorded an earthquake with M4.6 on at October 31, 2016 at Bone District, around 80 Km northeast form Makassar, South Sulawesi. The earthquake occurred 18:18:14 local time in 4.7°S, 120°E with depth 10 Km. Seismicity around location predicted caused by activity Walennae fault. We reprocessed earthquake data to determine precise hypocentre location and focal mechanism. The P- and S-wave arrival time got from BMKG used as input HYPOELLIPSE code to determine hypocentre. The results showed that the earthquake occurred 10:18:14.46 UTC in 4.638°S, 119.966°E with depth 24.76 Km. The hypocentre resolved 10 Km fix depth and had lower travel time residual than BMKG result. Focal mechanism determination used Azmtak code based on the first arrival polarity at earthquake waveform manually picked. The result showed a reverse mechanism with strike direction 38°, dip 44°, rake angle 134° on fault plane I and strike direction 164°, dip 60°, rake angle 56° on fault plane II. So, the earthquake which may be related to a reverse East Walennae Fault.

Modification of a liquid hydrogen tank for integrated refrigeration and storage

NASA Astrophysics Data System (ADS)

Swanger, A. M.; Jumper, K. M.; Fesmire, J. E.; Notardonato, W. U.

2015-12-01

The modification and outfitting of a 125,000-liter liquid hydrogen tank was performed to provide integrated refrigeration and storage capability. These functions include zero boil-off, liquefaction, and densification and therefore require provisions for sub-atmospheric tank pressures within the vacuum-jacketed, multilayer insulated tank. The primary structural modification was to add stiffening rings inside the inner vessel. The internal stiffening rings were designed, built, and installed per the ASME Boiler and Pressure Vessel Code, Section VIII, to prevent collapse in the case of vacuum jacket failure in combination with sub-atmospheric pressure within the tank. For the integrated refrigeration loop, a modular, skeleton-type heat exchanger, with refrigerant temperature instrumentation, was constructed using the stiffening rings as supports. To support the system thermal performance testing, three custom temperature rakes were designed and installed along the 21-meter length of the tank, once again using rings as supports. The temperature rakes included a total of 20 silicon diode temperature sensors mounted both vertically and radially to map the bulk liquid temperature within the tank. The tank modifications were successful and the system is now operational for the research and development of integrated refrigeration technology.

The Use of Electronic Mail in Biomedical Communication

PubMed Central

Costello, Richard; Shaw, Anthony; Cheetham, Roz; Moots, Robert J.

2000-01-01

Objectives: To determine whether there are statistically significant differences in the content of electronic mail (e-mail) and conventional mail sent to authors of papers published in medical journals. Design: Prospective study by postal questionnaire. Over two one-month periods, corresponding authors of papers published in medical journals were asked to record details of the correspondence prompted by their publications. Measurements: Conventional and e-mail correspondence received. Reprint requests. Content of correspondence. Quality of correspondence. Results: Eighty-two of 96 authors replied. Fifty received e-mail (mean, 5.7 ± 8.8 e-mails per author) and 72 received conventional mail (15.5 ± 32.8 letters per author) (p ≪ 0.05). Seventy percent of e-mails and only 53% of correspondence sent by conventional mail (p ≪ 0.05) referred to the content of the paper. Conclusions: Publication in general medical journals stimulates more conventional than electronic mail. However, the content of e-mail may be of greater scientific relevance. Electronic mail can be encouraged without fear of diminishing the quality of the communications received. PMID:10641967

Looking east along the operating deck above the intake toward ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking east along the operating deck above the intake toward the Main Control Room. An evaporative-cooling system is to the left of the Control Room, and a motor-operated, geared trolly hoist and rake for removing debris from the trash rack is in the foreground - Wellton-Mohawk Irrigation System, Pumping Plant No. 1, Bounded by Gila River & Union Pacific Railroad, Wellton, Yuma County, AZ

Soil Profile Characteristics of a 25-Year-Old Windrowed Loblolly Pine Plantation in Louisiana

Treesearch

William B. Patterson; John C. Adams; Spencer E. Loe; R. Jarod Patterson

2002-01-01

Windrowing site preparation, the raking and piling of long rows of logging debris, has been reported to displace surface soil, redistribute nutrients, and reduce volume growth of southern pine forests. Many of these studies have reported short-term results, and there are few long-term studies of the effects of windrowing on soil properties and pine growth. A 16.2...

Eighteen-year response of slash pine to wet-weather harvesting and site preparation on a poorly drained silt loam soil in Louisiana

Treesearch

D. Andrew Scott; Allan E. Tiarks

2006-01-01

Physical disturbances to soil resulting from forest management operations may reduce tree survival and growth, but responses are soil-, species-, and disturbance-specific. We studied wet-weather harvesting, shearing, root-raking, disking, and phosphorus fertilization on a poorly drained flatwoods site in Louisiana. Slash pine survival was improved by wet-weather...

Aerodynamic Analysis of Variable Geometry Raked Wingtips for Mid-Range Transonic Transport Aircraft

NASA Astrophysics Data System (ADS)

Jingeleski, David J.

Previous applications have shown that a wingtip treatment on a commercial airliner will reduce drag and increase fuel efficiency and the most common types of treatment are blended winglets and raked wingtips. With Boeing currently investigating novel designs for its next generation of airliners, a variable geometry raked wingtip novel control effector (VGRWT/NCE) was studied to determine the aerodynamic performance benefits over an untreated wingtip. The Boeing SUGAR design employing a truss-braced wing was selected as the baseline. Vortex lattice method (VLM) and computational fluid dynamics (CFD) software was implemented to analyze the aerodynamic performance of such a configuration applied to a next-generation, transonic, mid-range transport aircraft. Several models were created to simulate various sweep positions for the VGRWT/NCE tip, as well as a baseline model with an untreated wingtip. The majority of investigation was conducted using the VLM software, with CFD used largely as a validation of the VLM analysis. The VGRWT/NCE tip was shown to increase the lift of the wing while also decreasing the drag. As expected, the unswept VGRWT/NCE tip increases the amount of lift available over the untreated wingtip, which will be very beneficial for take-off and landing. Similarly, the swept VGRWT/NCE tip reduced the drag of the wing during cruise compared to the unmodified tip, which will favorably impact the fuel efficiency of the aircraft. Also, the swept VGRWT/NCE tip showed an increase in moment compared to the unmodified wingtip, implying an increase in stability, as well providing an avenue for roll control and gust alleviation for flexible wings. CFD analysis validated VLM as a useful low fidelity tool that yielded quite accurate results. The main results of this study are tabulated "deltas" in the forces and moments on the VGRWT/NCE tip as a function of sweep angle and aileron deflection compared to the baseline wing. A side study of the effects of the joint between the main wing and the movable tip showed that the drag impact can be kept small by careful design.

Slip complexity and frictional heterogeneities in dynamic fault models

NASA Astrophysics Data System (ADS)

Bizzarri, A.

2005-12-01

The numerical modeling of earthquake rupture requires the specification of the fault system geometry, the mechanical properties of the media surrounding the fault, the initial conditions and the constitutive law for fault friction. The latter accounts for the fault zone properties and allows for the description of processes of nucleation, propagation, healing and arrest of a spontaneous rupture. In this work I solve the fundamental elasto-dynamic equation for a planar fault, adopting different constitutive equations (slip-dependent and rate- and state-dependent friction laws). We show that the slip patterns may be complicated by different causes. The spatial heterogeneities of constitutive parameters are able to cause the healing of slip, like barrier-healing or slip pulses. Our numerical experiments show that the heterogeneities of the parameter L affect the dynamic rupture propagation and weakly modify the dynamic stress drop and the rupture velocity. The heterogeneity of a and b parameters affects the dynamic rupture propagation in a more complex way: a velocity strengthening area (a > b) can arrest a dynamic rupture, but can be driven to an instability if suddenly loaded by the dynamic rupture front. Our simulations provide a picture of the complex interactions between fault patches having different frictional properties. Moreover, the slip distribution on the fault plane is complicated considering the effects of the rake rotation during the propagation: depending on the position on the fault plane, the orientation of instantaneous total dynamic traction can change with time with respect to the imposed initial stress direction. These temporal rake rotations depend on the amplitude of the initial stress and on its distribution. They also depend on the curvature and direction of the rupture front with respect to the imposed initial stress direction: this explains why rake rotations are mostly located near the rupture front and within the cohesive zone, where the breakdown processes take places. Finally, the rupture behavior, the fault slip distribution and the traction evolution may be changed and complicated including additional physical phenomena, like thermal pressurization of pore fluid (due to frictional heating). Our results involve interesting implications for slip duration and fracture energy.

Simulated Firefighting Task Performance and Physiology Under Very Hot Conditions

PubMed Central

Larsen, Brianna; Snow, Rod; Williams-Bell, Michael; Aisbett, Brad

2015-01-01

Purpose: To assess the impact of very hot (45°C) conditions on the performance of, and physiological responses to, a simulated firefighting manual-handling task compared to the same work in a temperate environment (18°C). Methods: Ten male volunteer firefighters performed a 3-h protocol in both 18°C (CON) and 45°C (VH). Participants intermittently performed 12 × 1-min bouts of raking, 6 × 8-min bouts of low-intensity stepping, and 6 × 20-min rest periods. The area cleared during the raking task determined work performance. Core temperature, skin temperature, and heart rate were measured continuously. Participants also periodically rated their perceived exertion (RPE) and thermal sensation. Firefighters consumed water ad libitum. Urine specific gravity (USG) and changes in body mass determined hydration status. Results: Firefighters raked 19% less debris during the VH condition. Core and skin temperature were 0.99 ± 0.20 and 5.45 ± 0.53°C higher, respectively, during the VH trial, and heart rate was 14–36 beats.min−1 higher in the VH trial. Firefighters consumed 2950 ± 1034 mL of water in the VH condition, compared to 1290 ± 525 in the CON trial. Sweat losses were higher in the VH (1886 ± 474 mL) compared to the CON trial (462 ± 392 mL), though both groups were hydrated upon protocol completion (USG < 1.020). Participants' average RPE was higher in the VH (15.6 ± 0.9) compared to the CON trial (12.6 ± 0.9). Similarly, the firefighers' thermal sensation scores were significantly higher in the VH (6.4 ± 0.5) compared to the CON trial (4.4 ± 0.4). Conclusions: Despite the decreased work output and aggressive fluid replacement observed in the VH trial, firefighters' experienced increases in thermal stress, and exertion. Fire agencies should prioritize the health and safety of fire personnel in very hot temperatures, and consider the impact of reduced productivity on fire suppression efforts. PMID:26617527

Short daily-, nocturnal- and conventional-home hemodialysis have similar patient and treatment survival.

PubMed

Tennankore, Karthik K; Na, Yingbo; Wald, Ron; Chan, Christopher T; Perl, Jeffrey

2018-01-01

Home hemodialysis (HHD) has many benefits, but less is known about relative outcomes when comparing different home-based hemodialysis modalities. Here, we compare patient and treatment survival for patients receiving short daily HHD (2-3 hours/5 plus sessions per week), nocturnal HHD (6-8 hours/5 plus sessions per week) and conventional HHD (3-6 hours/2-4 sessions per week). A nationally representative cohort of Canadian HHD patients from 1996-2012 was studied. The primary outcome was death or treatment failure (defined as a permanent return to in-center hemodialysis or peritoneal dialysis) using an intention to treat analysis and death-censored treatment failure as a secondary outcome. The cohort consisted of 600, 508 and 202 patients receiving conventional, nocturnal, and short daily HHD, respectively. Conventional-HHD patients were more likely to use dialysis catheter access (43%) versus nocturnal or short daily HHD (32% and 31%, respectively). Although point estimates were in favor of both therapies, after multivariable adjustment for patient and center factors, there was no statistically significant reduction in the relative hazard for the death/treatment failure composite comparing nocturnal to conventional HHD (hazard ratio 0.83 [95% confidence interval 0.66-1.03]) or short daily to conventional HHD (0.84, 0.63-1.12). Among those with information on vascular access, patients receiving nocturnal HHD had a relative improvement in death-censored treatment survival (0.75, 0.57-0.98). Thus, in this national cohort of HHD patients, those receiving short daily and nocturnal HHD had similar patient/treatment survival compared with patients receiving conventional HHD. Copyright © 2017 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

Comparison of Ventilation With One-Handed Mask Seal With an Intraoral Mask Versus Conventional Cuffed Face Mask in a Cadaver Model: A Randomized Crossover Trial.

PubMed

Amack, Andrew J; Barber, Gary A; Ng, Patrick C; Smith, Thomas B; April, Michael D

2017-01-01

We compare received minute volume with an intraoral mask versus conventional cuffed face mask among medics obtaining a 1-handed mask seal on a cadaver model. This study comprised a randomized crossover trial of adult US Army combat medic volunteers participating in a cadaver laboratory as part of their training. We randomized participants to obtain a 1-handed mask seal during ventilation of a fresh unembalmed cadaver, first using either an intraoral airway device or conventional cuffed face mask. Participants obtained a 1-handed mask seal while a ventilator delivered 10 standardized 750-mL breaths during 1 minute. After a 5-minute rest period, they repeated the study with the alternative mask. The primary outcome measure was received minute volume as measured by a respirometer. Of 27 recruited participants, all completed the study. Median received minute volume was higher with the intraoral mask compared with conventional cuffed mask by 1.7 L (95% confidence interval 1.0 to 1.9 L; P<.001). The intraoral mask resulted in greater received minute volume received compared with conventional cuffed face mask during ventilation with a 1-handed mask seal in a cadaver model. The intraoral mask may prove a useful airway adjunct for ventilation. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Fundamental Studies of SUBSONIC and Transonic Flow Separation. Part 3. Third Phase Summary Report

DTIC Science & Technology

1979-10-01

circular bump using a laser velocimeter and pitot probe. They point out that external probes like pitot probes or rakes of different kinds may...numerical Navier-Stokes solutions for high Reynolds number two-dimenslonal flow. The flow conditions have been extended to include low supersonic free...Setups . . . . . . . . . . . 19 Shock Holder and Its Orientation in the Tunnel . . . . . . . . . . . . . . 21 Pitot and Cone Probes Mounted on

Tool Forces and Chip Types In Orthogonal Cutting Of Southern Hardwoods

Treesearch

G.E. Woodson

1979-01-01

Specimens (l/8 to l/4 inch thick) from 5 trees of each of 22 hardwood species were cut orthogonally at 5 inches per minute. Average parallel and normal cutting forces for various rake angles (50, 60, and 70 degrees for veneer; 10, 20, and 30 degrees for planing; 20, 30, and 40 degrees for crosscutting) were measured at three moisture contents (10 percent, 20 percent,...

Unsteady Force Calculations in Turbomachinery

DTIC Science & Technology

1991-07-01

Engineering for Gas Turbines and Power, Vol. 107, pp. 945-952, October 1985. Lefcort, M. P., "An Investigation into Unsteady Blade Forces in...generated unsteady flow around a rotating turbine blade row .. ..... 43 7 The rotating coordinate system with skew, 0, and rake, zr, defined at midchord...while Kerrebrock and Mikolajczak [19701 5 proved it experimentally. For a turbine blade passage, the wake fluid moves from the pressure 3 surface to the

Comparison of three site preparation techniques on growth of planted loblolly pine 6 years after a southern pine beetle epidemic

Treesearch

Wayne K. Clatterbuck; Michael Carr

2013-01-01

Three site preparation treatments: (1) complete removal of woody debris—drum chopped, raked, and disked; (2) drum chopping leaving woody debris; and (3) no site preparation—planting among dead standing trees were compared by evaluating the growth and survival of planted loblolly pine (Pinus taeda L.) after six growing seasons following a southern...

Analysis of Building 839: Carlisle Barracks, Pennsylvania

DTIC Science & Technology

2013-09-01

within prehistory or history is made clear.”101 A historic property is determined as either significant or not significant by applying standardized...yielded, or is likely to yield, information important in prehistory or history. 3.3 Significance Eligibility to the NRHP is based upon...given period in history or prehistory . The workmanship of Building 839 is evident in the mortar joints of the brick walls (Figure 53), the rake boards

Radial and circumferential flow surveys at the inlet and exit of the Space Shuttle Main Engine High Pressure Fuel Turbine Model

NASA Technical Reports Server (NTRS)

Hudson, S. T.; Bordelon, W. J., Jr.; Smith, A. W.; Ramachandran, N.

1995-01-01

The main objective of this test was to obtain detailed radial and circumferential flow surveys at the inlet and exit of the SSME High Pressure Fuel Turbine model using three-hole cobra probes, hot-film probes, and a laser velocimeter. The test was designed to meet several objectives. First, the techniques for making laser velocimeter, hot-film probe, and cobra probe measurements in turbine flows were developed and demonstrated. The ability to use the cobra probes to obtain static pressure and, therefore, velocity had to be verified; insertion techniques had to be established for the fragile hot-film probes; and a seeding method had to be established for the laser velocimetry. Once the measurement techniques were established, turbine inlet and exit velocity profiles, temperature profiles, pressure profiles, turbulence intensities, and boundary layer thicknesses were measured at the turbine design point. The blockage effect due to the model inlet and exit total pressure and total temperature rakes on the turbine performance was also studied. A small range of off-design points were run to obtain the profiles and to verify the rake blockage effects off-design. Finally, a range of different Reynolds numbers were run to study the effect of Reynolds number on the various measurements.

Flow-Field Survey in the Test Region of the SR-71 Aircraft Test Bed Configuration

NASA Technical Reports Server (NTRS)

Mizukami, Masashi; Jones, Daniel; Weinstock, Vladimir D.

2000-01-01

A flat plate and faired pod have been mounted on a NASA SR-71A aircraft for use as a supersonic flight experiment test bed. A test article can be placed on the flat plate; the pod can contain supporting systems. A series of test flights has been conducted to validate this test bed configuration. Flight speeds to a maximum of Mach 3.0 have been attained. Steady-state sideslip maneuvers to a maximum of 2 deg have been conducted, and the flow field in the test region has been surveyed. Two total-pressure rakes, each with two flow-angle probes, have been placed in the expected vicinity of an experiment. Static-pressure measurements have been made on the flat plate. At subsonic and low supersonic speeds with no sideslip, the flow in the surveyed region is quite uniform. During sideslip maneuvers, localized flow distortions impinge on the test region. Aircraft sideslip does not produce a uniform sidewash over the test region. At speeds faster than Mach 1.5, variable-pressure distortions were observed in the test region. Boundary-layer thickness on the flat plate at the rake was less than 2.1 in. For future experiments, a more focused and detailed flow-field survey than this one would be desirable.

Wind Code Application to External Forebody Flowfields with Comparisons to Experimental Results

NASA Technical Reports Server (NTRS)

Frate, F. C.; Kim, H. D.

2001-01-01

The WIND Code, a general purpose Navier-Stokes solver, has been utilized to obtain supersonic external flowfield Computational Fluid Dynamics (CFD) solutions over an axisymmetric, parabolic forebody with comparisons made to wind tunnel experimental results. Various cases have been investigated at supersonic freestream conditions ranging from Mach 2.0 to 3.5, at 0 deg and 3 deg angles-of-attack, and with either a sharp-nose or blunt-nose forebody configuration. Both a turbulent (Baldwin-Lomax algebraic turbulence model) and a laminar model have been implemented in the CFD. Obtaining the solutions involved utilizing either the parabolized- or full-Navier-Stokes analyses supplied in WIND. Comparisons have been made with static pressure measurements, with boundary-layer rake and flowfield rake pitot pressure measurements, and with temperature sensitive paint experimental results. Using WIND's parabolized Navier-Stokes capability, grid sequencing, and the Baldwin-Lomax algebraic turbulence model allowed for significant reductions in computational time while still providing good agreement with experiment. Given that CFD and experiment compare well, WIND is found to be a good computational platform for solving this type of forebody problem, and the grids developed in conjunction with it will be used in the future to investigate varying freestream conditions not tested experimentally.

Quantitative determination of microbial activity and community nutritional status in estuarine sediments: evidence for a disturbance artifact

NASA Technical Reports Server (NTRS)

Findlay, R. H.; Pollard, P. C.; Moriarty, D. J.; White, D. C.

1985-01-01

In estuarine sediments with a high degree of vertical heterogeneity in reduced substrate and terminal electron acceptor concentrations, the method of exposure of the microbiota to labeled substrates can introduce a "disturbance artifact" into measures of metabolic activity. The detection of this artifact is based on quantitative measurement of the relative rates of incorporation of [14C]acetate into phospholipid fatty acids (PLFA) and endogenous storage lipid, poly-beta-hydroxyalkanoate (PHA). Previous studies have shown that PLFA synthesis measures cellular growth and that PHA synthesis measures carbon accumulation (unbalanced growth). The "disturbance artifact" of exposure to [14C]acetate was demonstrated by comparing injection of a core with the usual or pore-water replacement or slurry techniques. Only injection of labeled substrate allowed detection of preassay disturbance of the sediment with a garden rake. The raking increased PLFA synthesis with little effect to differences in concentration or distribution of [14C]acetate in the 10-min incubation. Bioturbation induced by sand dollar feeding in estuarine sediment could be detected in an increased PLFA/PHA ratio which was due to decreased PHA synthesis if the addition of labeled substrate was by the injection technique. Addition of labeled precursors to sediment by slurry or pore-water replacement induces greater disturbance artifacts than injection techniques.

CFD Models of a Serpentine Inlet, Fan, and Nozzle

NASA Technical Reports Server (NTRS)

Chima, R. V.; Arend, D. J.; Castner, R. S.; Slater, J. W.; Truax, P. P.

2010-01-01

Several computational fluid dynamics (CFD) codes were used to analyze the Versatile Integrated Inlet Propulsion Aerodynamics Rig (VIIPAR) located at NASA Glenn Research Center. The rig consists of a serpentine inlet, a rake assembly, inlet guide vanes, a 12-in. diameter tip-turbine driven fan stage, exit rakes or probes, and an exhaust nozzle with a translating centerbody. The analyses were done to develop computational capabilities for modeling inlet/fan interaction and to help interpret experimental data. Three-dimensional Reynolds averaged Navier-Stokes (RANS) calculations of the fan stage were used to predict the operating line of the stage, the effects of leakage from the turbine stream, and the effects of inlet guide vane (IGV) setting angle. Coupled axisymmetric calculations of a bellmouth, fan, and nozzle were used to develop techniques for coupling codes together and to investigate possible effects of the nozzle on the fan. RANS calculations of the serpentine inlet were coupled to Euler calculations of the fan to investigate the complete inlet/fan system. Computed wall static pressures along the inlet centerline agreed reasonably well with experimental data but computed total pressures at the aerodynamic interface plane (AIP) showed significant differences from the data. Inlet distortion was shown to reduce the fan corrected flow and pressure ratio, and was not completely eliminated by passage through the fan

Alterations in plaque accumulation and gingival inflammation promoted by treatment with self-ligating and conventional orthodontic brackets

PubMed Central

Cardoso, Mauricio de Almeida; Saraiva, Patrícia Pinto; Maltagliati, Liliana Ávila; Rhoden, Fernando Kleinübing; Costa, Carla Cristina Alvarenga; Normando, David; Capelozza, Leopoldino

2015-01-01

OBJECTIVE: The aim of the present study was to evaluate, comparatively, the periodontal response during orthodontic treatment performed with self-ligating and conventional brackets. METHODS: Sixteen Caucasian individuals of both sexes, aged between 12 and 16 years old and in permanent dentition were selected. Eight individuals were treated with conventional brackets installed on the lower dental arch and self-ligating brackets on the upper arch. Another eight individuals received self-ligating brackets in the lower arch and conventional brackets in the upper arch. The subjects received material and instructions for oral hygiene. Visible plaque index (VPI), gingival bleeding index (GBI) and clinical attachment level (CAL) were evaluated just after installation of orthodontic appliances, and 30, 60 and 180 days later. Mann-Whitney test was used to compare differences between groups (self-ligating and conventional), two-way ANOVA followed by Tukey's test was used to assess CAL at each site of each tooth. Significance level was set at 5%. RESULTS: No significant changes were found with regard to the assessed parameters (VPI, GBI and CAL) in either one of the systems. CONCLUSION: No significant changes were found with regard to the periodontal response to orthodontic treatment for the variables assessed and between subjects receiving passive self-ligating and conventional brackets. All individuals had received oral hygiene instructions and had their periodontal conditions monitored. PMID:25992985

Alterations in plaque accumulation and gingival inflammation promoted by treatment with self-ligating and conventional orthodontic brackets.

PubMed

Cardoso, Mauricio de Almeida; Saraiva, Patrícia Pinto; Maltagliati, Liliana Ávila; Rhoden, Fernando Kleinübing; Costa, Carla Cristina Alvarenga; Normando, David; Capelozza Filho, Leopoldino

2015-01-01

The aim of the present study was to evaluate, comparatively, the periodontal response during orthodontic treatment performed with self-ligating and conventional brackets. Sixteen Caucasian individuals of both sexes, aged between 12 and 16 years old and in permanent dentition were selected. Eight individuals were treated with conventional brackets installed on the lower dental arch and self-ligating brackets on the upper arch. Another eight individuals received self-ligating brackets in the lower arch and conventional brackets in the upper arch. The subjects received material and instructions for oral hygiene. Visible plaque index (VPI), gingival bleeding index (GBI) and clinical attachment level (CAL) were evaluated just after installation of orthodontic appliances, and 30, 60 and 180 days later. Mann-Whitney test was used to compare differences between groups (self-ligating and conventional), two-way ANOVA followed by Tukey's test was used to assess CAL at each site of each tooth. Significance level was set at 5%. No significant changes were found with regard to the assessed parameters (VPI, GBI and CAL) in either one of the systems. No significant changes were found with regard to the periodontal response to orthodontic treatment for the variables assessed and between subjects receiving passive self-ligating and conventional brackets. All individuals had received oral hygiene instructions and had their periodontal conditions monitored.

Topical Administration of Pirfenidone Increases Healing of Chronic Diabetic Foot Ulcers: A Randomized Crossover Study

PubMed Central

Janka-Zires, Marcela; Uribe-Wiechers, Ana Cecilia; Juárez-Comboni, Sonia Citlali; López-Gutiérrez, Joel; Escobar-Jiménez, Jarod Jazek; Gómez-Pérez, Francisco J.

2016-01-01

Only 30 percent of chronic diabetic foot ulcers heal after 20 weeks of standard treatment. Pirfenidone is a drug with biological, anti-inflammatory, and antifibrotic effects. The aim of this study was to evaluate the effect of topical pirfenidone added to conventional treatment in noninfected chronic diabetic foot ulcers. This was a randomized crossover study. Group 1 received topical pirfenidone plus conventional treatment for 8 weeks; after this period, they were switched to receive conventional treatment only for 8 more weeks. In group 2, the order of the treatments was the opposite. The end points were complete ulcer healing and size reduction. Final data were obtained from 35 ulcers in 24 patients. Fifty-two percent of ulcers treated with pirfenidone healed before 8 weeks versus 14.3% treated with conventional treatment only (P = 0.025). Between 8 and 16 weeks, 30.8% ulcers that received pirfenidone healed versus 0% with conventional treatment (P = 0.081). By week 8, the reduction in ulcer size was 100% [73–100] with pirfenidone versus 57.5% with conventional treatment [28.9–74] (P = 0.011). By week 16, the reduction was 93% [42.7–100] with pirfenidone and 21.8% [8–77.5] with conventional treatment (P = 0.050). The addition of topical pirfenidone to conventional treatment significantly improves the healing of chronic diabetic noninfected foot ulcers. PMID:27478849

Topical Administration of Pirfenidone Increases Healing of Chronic Diabetic Foot Ulcers: A Randomized Crossover Study.

PubMed

Janka-Zires, Marcela; Almeda-Valdes, Paloma; Uribe-Wiechers, Ana Cecilia; Juárez-Comboni, Sonia Citlali; López-Gutiérrez, Joel; Escobar-Jiménez, Jarod Jazek; Gómez-Pérez, Francisco J

2016-01-01

Only 30 percent of chronic diabetic foot ulcers heal after 20 weeks of standard treatment. Pirfenidone is a drug with biological, anti-inflammatory, and antifibrotic effects. The aim of this study was to evaluate the effect of topical pirfenidone added to conventional treatment in noninfected chronic diabetic foot ulcers. This was a randomized crossover study. Group 1 received topical pirfenidone plus conventional treatment for 8 weeks; after this period, they were switched to receive conventional treatment only for 8 more weeks. In group 2, the order of the treatments was the opposite. The end points were complete ulcer healing and size reduction. Final data were obtained from 35 ulcers in 24 patients. Fifty-two percent of ulcers treated with pirfenidone healed before 8 weeks versus 14.3% treated with conventional treatment only (P = 0.025). Between 8 and 16 weeks, 30.8% ulcers that received pirfenidone healed versus 0% with conventional treatment (P = 0.081). By week 8, the reduction in ulcer size was 100% [73-100] with pirfenidone versus 57.5% with conventional treatment [28.9-74] (P = 0.011). By week 16, the reduction was 93% [42.7-100] with pirfenidone and 21.8% [8-77.5] with conventional treatment (P = 0.050). The addition of topical pirfenidone to conventional treatment significantly improves the healing of chronic diabetic noninfected foot ulcers.

Clinical evaluation of extraperitoneal colostomy without damaging the muscle layer of the abdominal wall.

PubMed

Dong, L-R; Zhu, Y-M; Xu, Q; Cao, C-X; Zhang, B-Z

2012-01-01

This study investigated whether extraperitoneal colostomy without damaging the muscle layer of the abdominal wall is an improved surgical procedure compared with conventional sigmoid colostomy in patients undergoing abdominoperineal resection. Patients with rectal cancer undergoing abdominoperineal resection were selected and randomly divided into two groups: the study group received extraperitoneal colostomy without damaging the muscle layer of the abdominal wall and the control group received conventional colostomy. Clinical data from both groups were analysed. A total of 128 patients were included: 66 received extraperitoneal colostomy without damaging the muscle layer of the abdominal wall and 62 received conventional colostomy. Significant differences between the two groups were found in relation to colostomy operating time, defaecation sensation, bowel control and overall stoma-related complications. Duration of postoperative hospital stay was also significantly different between the study groups. Extraperitoneal colostomy without damaging the muscle layer of the abdominal wall was found to be an improved procedure compared with conventional sigmoid colostomy in abdominoperineal resection, and may reduce colostomy-related complications, shorten operating time and postoperative hospital stay, and potentially improve patients' quality of life.

Advanced CFD Methods for Hypervelocity Wind Tunnels

DTIC Science & Technology

2011-03-10

Mach 14 nozzle produces non-uniformities in the test section flow that are not desirable [1,2]. Calibration runs with Pitot pressure rakes suggest...flows is presented. The grid is based on the characteristic lines of the supersonic regions of the flow. This allows for grid alignment and clustering...novel grid generation scheme for hypersonic nozzle flows is presented. The grid is based on the characteristic lines of the supersonic regions of the

Astronaut John Young photographed collecting lunar samples

NASA Technical Reports Server (NTRS)

1972-01-01

Astronaut John W. Young, commander of the Apollo 16 lunar landing mission, is photographed collecting lunar samples near North Ray crater during the third Apollo 16 extravehicular activity (EVA-3) at the Descartes landing site. This picture was taken by Astronaut Charles M. Duke Jr., lunar module pilot. Young is using the lunar surface rake and a set of tongs. The Lunar Roving Vehicle is parked in the field of large boulders in the background.

Serpentine Diffuser Performance with Emphasis on Future Introduction to a Transonic Fan (Postprint)

DTIC Science & Technology

2013-01-01

conditioning barrel . The velocity distribution across the flow conditioning barrel was measured at the same axial location of inlet temperature and...rakes at the same axial plane (AIP) of the total pressure probe tips. The probes were constructed from stainless steel tubing with 0.027 inch inside...numbers with 195 axial and circumferential static pressure measurements within the diffuser flow path. Pressure distortion at the diffuser discharge

Validation of Viewing Reports: Exploration of a Photographic Method.

ERIC Educational Resources Information Center

Fletcher, James E.; Chen, Charles Chao-Ping

A time lapse camera loaded with Super 8 film was employed to photographically record the area in front of a conventional television receiver in selected homes. The camera took one picture each minute for three days, including in the same frame the face of the television receiver. Family members kept a conventional viewing diary of their viewing…

The source parameters of 2013 Mw6.6 Lushan earthquake constrained with the restored local clipped seismic waveforms

NASA Astrophysics Data System (ADS)

Hao, J.; Zhang, J. H.; Yao, Z. X.

2017-12-01

We developed a method to restore the clipped seismic waveforms near epicenter using projection onto convex sets method (Zhang et al, 2016). This method was applied to rescue the local clipped waveforms of 2013 Mw 6.6 Lushan earthquake. We restored 88 out of 93 clipped waveforms of 38 broadband seismic stations of China Earthquake Networks (CEN). The epicenter distance of the nearest station to the epicenter that we can faithfully restore is only about 32 km. In order to investigate if the source parameters of earthquake could be determined exactly with the restored data, restored waveforms are utilized to get the mechanism of Lushan earthquake. We apply the generalized reflection-transmission coefficient matrix method to calculate the synthetic seismic records and simulated annealing method in inversion (Yao and Harkrider, 1983; Hao et al., 2012). We select 5 stations of CEN with the epicenter distance about 200km whose records aren't clipped and three-component velocity records are used. The result shows the strike, dip and rake angles of Lushan earthquake are 200o, 51o and 87o respectively, hereinafter "standard result". Then the clipped and restored seismic waveforms are applied respectively. The strike, dip and rake angles of clipped seismic waveforms are 184o, 53o and 72o respectively. The largest misfit of angle is 16o. In contrast, the strike, dip and rake angles of restored seismic waveforms are 198o, 51o and 87o respectively. It is very close to the "standard result". We also study the rupture history of Lushan earthquake constrained with the restored local broadband and teleseismic waves based on finite fault method (Hao et al., 2013). The result consists with that constrained with the strong motion and teleseismic waves (Hao et al., 2013), especially the location of the patch with larger slip. In real-time seismology, determining the source parameters as soon as possible is important. This method will help us to determine the mechanism of earthquake using the local clipped waveforms. Strong motion stations in China don't have good coverage at present. This method will help us to investigate the rupture history of large earthquake in China using the local clipped data of broadband stations.

Management of severe ischemic cardiomyopathy: left ventricular assist device as destination therapy versus conventional bypass and mitral valve surgery.

PubMed

Maltais, Simon; Tchantchaleishvili, Vahtang; Schaff, Hartzell V; Daly, Richard C; Suri, Rakesh M; Dearani, Joseph A; Topilsky, Yan; Stulak, John M; Joyce, Lyle D; Park, Soon J

2014-04-01

Patients with severe ischemic cardiomyopathy (left ventricular ejection fraction <25%) and severe ischemic mitral regurgitation have a poor survival with medical therapy alone. Left ventricular assist device as destination therapy is reserved for patients who are too high risk for conventional surgery. We evaluated our outcomes with conventional surgery within this population and the comparative effectiveness of these 2 therapies. We identified patients who underwent conventional surgery or left ventricular assist device as destination therapy for severe ischemic cardiomyopathy (left ventricular ejection fraction <25%) and severe mitral regurgitation. The era for conventional surgery spanned from 1993 to 2009 and from 2007 to 2011 for left ventricular assist device as destination therapy. We compared baseline patient characteristics and outcomes in terms of end-organ function and survival. A total of 88 patients were identified; 55 patients underwent conventional surgery (63%), and 33 patients (37%) received a left ventricular assist device as destination therapy. Patients who received left ventricular assist device as destination therapy had the increased prevalence of renal failure, inotrope dependency, and intra-aortic balloon support. Patients undergoing conventional surgery required longer ventilatory support, and patients receiving a left ventricular assist device required more reoperation for bleeding. Mortality rates were similar between the 2 groups at 30 days (7% in the conventional surgery group vs 3% in the left ventricular assist device as destination therapy group, P = .65) and at 1 year (22% in the conventional surgery group vs 15% in the left ventricular assist device as destination therapy group, P = .58). There was a trend toward improved survival in patients receiving a left ventricular assist device compared with the propensity-matched groups at 1 year (94% vs 71%, P = .171). The operative mortality and early survival after conventional surgery seem to be acceptable. For inoperable or prohibitive-risk patients, left ventricular assist device as destination therapy can be offered with similar outcomes. Copyright © 2014 The American Association for Thoracic Surgery. Published by Mosby, Inc. All rights reserved.

Analytical, Numerical, and Experimental Results on Turbulent Boundary Layers

DTIC Science & Technology

1976-07-01

a pitot pressure rake where the spacing between probe centers was 0.5 in. near the wall and 1.0 in. away from the wall. Recently, measurements have...Pressure Gradient, Part II. Analysis- of the Experimental Data." BRL R 1543, June 1971. 51. Allen, J. M. " Pitot -Probe Displacement in a Supersonic Turbulent...numbers; (4) a description of the data reduction of pitot pressure measurements utilizing these analytical results in order to obtain velocity

Open-Water Resistance and Seakeeping Characteristics of Ships with Icebreaking Bows

DTIC Science & Technology

1991-05-13

of a Knuckled Forefoot on a Typical Icebreaker ...... ................... . 19 3-2. Lines Plan, T-AGS OCEAN (ICE) . * * .... . 23 3-3. Curve of...the ice. As the stem strikes the ice, initial failure of the ice occurs by simple crushing. Then the raked stem of the icebreaker rides up onto the ice...bossings, skegs, rudders, 18 and special stem forefoot shapes were not included in the shapes tested. To ensure that the parent and its variants

Change of magnetic domain structure by mechanically induced twin boundary motion in Ni-Mn-Ga single crystal

NASA Astrophysics Data System (ADS)

Kopecký, Vít; Heczko, Oleg

2017-10-01

The single variant state exhibits usual labyrinth and band magnetic domains depending on orientation of easy magnetization axis. By the passage of single twin boundary induced by mechanical stress the rake and granular domain patterns are formed. These domain patterns are further modified by repeated passage of the twin boundary resulting in similar domain patterns in the sample even though the orientation of the magnetization is different.

In-flight leading-edge extension vortex flow-field survey measurements on a F-18 aircraft at high angle of attack

NASA Technical Reports Server (NTRS)

Richwine, David M.; Fisher, David F.

1992-01-01

Flow-field measurements on the leading-edge extension (LEX) of the F-18 High Alpha Research Vehicle (HARV) were obtained using a rotating rake with 16 hemispherical-tipped five-hole probes. Detailed pressure, velocity, and flow direction data were obtained through the LEX vortex core. Data were gathered during 1-g quasi-stabilized flight conditions at angles of attack alpha from 10 degrees to 52 degrees and at Reynolds numbers based on mean aerodynamic cord up to 16 x 10(exp 6). Normalized dynamic pressures and crossflow velocities clearly showed the primary vortex above the LEX and formation of a secondary vortex at higher angles of attack. The vortex was characterized by a ring of high dynamic pressure surrounding a region of low dynamic pressure at the vortex core center. The vortex core, subcore diameter, and vertical location of the core above the LEX increased with angle of attack. Minimum values for static pressure were obtained in the vortex subcore and decreased nearly linearly with increasing angle of attack until vortex breakdown. Rake-measured static pressures were consistent with previously documented surface pressures and showed good agreement with flow visualization flight test results. Comparison of the LEX vortex flight test data to computational solutions at alpha approximately equals 19 degrees and 30 degrees showed fair correlation.

Accounting for Fault Roughness in Pseudo-Dynamic Ground-Motion Simulations

NASA Astrophysics Data System (ADS)

Mai, P. Martin; Galis, Martin; Thingbaijam, Kiran K. S.; Vyas, Jagdish C.; Dunham, Eric M.

2017-09-01

Geological faults comprise large-scale segmentation and small-scale roughness. These multi-scale geometrical complexities determine the dynamics of the earthquake rupture process, and therefore affect the radiated seismic wavefield. In this study, we examine how different parameterizations of fault roughness lead to variability in the rupture evolution and the resulting near-fault ground motions. Rupture incoherence naturally induced by fault roughness generates high-frequency radiation that follows an ω-2 decay in displacement amplitude spectra. Because dynamic rupture simulations are computationally expensive, we test several kinematic source approximations designed to emulate the observed dynamic behavior. When simplifying the rough-fault geometry, we find that perturbations in local moment tensor orientation are important, while perturbations in local source location are not. Thus, a planar fault can be assumed if the local strike, dip, and rake are maintained. We observe that dynamic rake angle variations are anti-correlated with the local dip angles. Testing two parameterizations of dynamically consistent Yoffe-type source-time function, we show that the seismic wavefield of the approximated kinematic ruptures well reproduces the radiated seismic waves of the complete dynamic source process. This finding opens a new avenue for an improved pseudo-dynamic source characterization that captures the effects of fault roughness on earthquake rupture evolution. By including also the correlations between kinematic source parameters, we outline a new pseudo-dynamic rupture modeling approach for broadband ground-motion simulation.

Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G.

2011-01-17

The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasivemore » and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.« less

In-Flight Capability for Evaluating Skin-Friction Gages and Other Near-Wall Flow Sensors

NASA Technical Reports Server (NTRS)

Bui, Trong T.; Pipitone, Brett J.; Krake, Keith L.; Richwine, Dave (Technical Monitor)

2003-01-01

An 8-in.-square boundary-layer sensor panel has been developed for in-flight evaluation of skin-friction gages and other near-wall flow sensors on the NASA Dryden Flight Research Center F-15B/Flight Test Fixture (FTF). Instrumentation on the sensor panel includes a boundary-layer rake, temperature sensors, static pressure taps, and a Preston tube. Space is also available for skin-friction gages or other near-wall flow sensors. Pretest analysis of previous F-15B/FTF flight data has identified flight conditions suitable for evaluating skin-friction gages. At subsonic Mach numbers, the boundary layer over the sensor panel closely approximates the two-dimensional (2D), law-of-the-wall turbulent boundary layer, and skin-friction estimates from the Preston tube and the rake (using the Clauser plot method) can be used to evaluate skin-friction gages. At supersonic Mach numbers, the boundary layer over the sensor panel becomes complex, and other means of measuring skin friction are needed to evaluate the accuracy of new skin-friction gages. Results from the flight test of a new rubber-damped skin-friction gage confirm that at subsonic Mach numbers, nearly 2D, law-of-the-wall turbulent boundary layers exist over the sensor panel. Sensor panel data also show that this new skin-friction gage prototype does not work in flight.

Wear Mechanism of Chemical Vapor Deposition (CVD) Carbide Insert in Orthogonal Cutting Ti-6Al-4V ELI at High Cutting Speed

NASA Astrophysics Data System (ADS)

Gusri, A. I.; Che Hassan, C. H.; Jaharah, A. G.

2011-01-01

The performance of Chemical Vapor Deposition (CVD) carbide insert with ISO designation of CCMT 12 04 04 LF, when turning titanium alloys was investigated. There were four layers of coating materials for this insert i.e.TiN-Al2O3-TiCN-TiN. The insert performance was evaluated based on the insert's edge resistant towards the machining parameters used at high cutting speed range of machining Ti-6Al-4V ELI. Detailed study on the wear mechanism at the cutting edge of CVD carbide tools was carried out at cutting speed of 55-95 m/min, feed rate of 0.15-0.35 mm/rev and depth of cut of 0.10-0.20 mm. Wear mechanisms such as abrasive and adhesive were observed on the flank face. Crater wear due to diffusion was also observed on the rake race. The abrasive wear occurred more at nose radius and the fracture on tool were found at the feed rate of 0.35 mm/rev and the depth of cut of 0.20 mm. The adhesion wear takes place after the removal of the coating or coating delaminating. Therefore, adhesion or welding of titanium alloy onto the flank and rake faces demonstrates a strong bond at the workpiece-tool interface.

Prevention of rat liver fibrosis and carcinogenesis by coffee and caffeine.

PubMed

Furtado, Kelly S; Polletini, Jossimara; Dias, Marcos C; Rodrigues, Maria A M; Barbisan, Luis F

2014-02-01

Coffee has been inversely related to the incidence of human liver disease; however, whether caffeine is the component responsible for the beneficial effects of coffee remains controversial. This study evaluated the beneficial effects of coffee or caffeine in a medium-term bioassay for rat liver fibrosis/carcinogenesis induced by diethylnitrosamine (DEN) and carbon tetrachloride (CCl4). One week after the DEN injection, the groups started to receive conventional coffee, instant coffee or 0.1% caffeine ad libitum for 24 weeks. The groups receiving conventional coffee or caffeine presented a significant reduction in collagen content and mRNA expression of collagen I. The groups receiving instant coffee or caffeine had a significant reduction in the size and area of pre-neoplastic lesions and in the mean number of neoplastic lesions. A significant increase in liver bax protein levels was observed in the groups receiving instant coffee or caffeine as compared to the control group. These data indicate that the most pronounced hepatoprotective effect against fibrosis was observed in the groups receiving conventional coffee and 0.1% caffeine, and the greatest effects against liver carcinogenesis were detected in the groups receiving instant coffee and 0.1% caffeine. Copyright © 2013 Elsevier Ltd. All rights reserved.

Complementary and alternative medicine contacts by persons with mental disorders in 25 countries: results from the World Mental Health Surveys.

PubMed

de Jonge, P; Wardenaar, K J; Hoenders, H R; Evans-Lacko, S; Kovess-Masfety, V; Aguilar-Gaxiola, S; Al-Hamzawi, A; Alonso, J; Andrade, L H; Benjet, C; Bromet, E J; Bruffaerts, R; Bunting, B; Caldas-de-Almeida, J M; Dinolova, R V; Florescu, S; de Girolamo, G; Gureje, O; Haro, J M; Hu, C; Huang, Y; Karam, E G; Karam, G; Lee, S; Lépine, J-P; Levinson, D; Makanjuola, V; Navarro-Mateu, F; Pennell, B-E; Posada-Villa, J; Scott, K; Tachimori, H; Williams, D; Wojtyniak, B; Kessler, R C; Thornicroft, G

2017-12-28

A substantial proportion of persons with mental disorders seek treatment from complementary and alternative medicine (CAM) professionals. However, data on how CAM contacts vary across countries, mental disorders and their severity, and health care settings is largely lacking. The aim was therefore to investigate the prevalence of contacts with CAM providers in a large cross-national sample of persons with 12-month mental disorders. In the World Mental Health Surveys, the Composite International Diagnostic Interview was administered to determine the presence of past 12 month mental disorders in 138 801 participants aged 18-100 derived from representative general population samples. Participants were recruited between 2001 and 2012. Rates of self-reported CAM contacts for each of the 28 surveys across 25 countries and 12 mental disorder groups were calculated for all persons with past 12-month mental disorders. Mental disorders were grouped into mood disorders, anxiety disorders or behavioural disorders, and further divided by severity levels. Satisfaction with conventional care was also compared with CAM contact satisfaction. An estimated 3.6% (standard error 0.2%) of persons with a past 12-month mental disorder reported a CAM contact, which was two times higher in high-income countries (4.6%; standard error 0.3%) than in low- and middle-income countries (2.3%; standard error 0.2%). CAM contacts were largely comparable for different disorder types, but particularly high in persons receiving conventional care (8.6-17.8%). CAM contacts increased with increasing mental disorder severity. Among persons receiving specialist mental health care, CAM contacts were reported by 14.0% for severe mood disorders, 16.2% for severe anxiety disorders and 22.5% for severe behavioural disorders. Satisfaction with care was comparable with respect to CAM contacts (78.3%) and conventional care (75.6%) in persons that received both. CAM contacts are common in persons with severe mental disorders, in high-income countries, and in persons receiving conventional care. Our findings support the notion of CAM as largely complementary but are in contrast to suggestions that this concerns person with only mild, transient complaints. There was no indication that persons were less satisfied by CAM visits than by receiving conventional care. We encourage health care professionals in conventional settings to openly discuss the care patients are receiving, whether conventional or not, and their reasons for doing so.

Clinical and radiological investigations of mandibular overdentures supported by conventional or mini-dental implants: A 2-year prospective follow-up study.

PubMed

Temizel, Sonay; Heinemann, Friedhelm; Dirk, Cornelius; Bourauel, Christoph; Hasan, Istabrak

2017-02-01

Conventional dental implants are not applicable in the mandibular interforaminal region if bone volume is limited. Mini-dental implants offer an alternative means of supporting mandibular overdentures in a narrow residual ridge, without additional surgery. The purpose of this nonrandomized clinical trial was to compare the ability of mini-dental implants with that of conventional dental implants in supporting mandibular overdentures during a 2-year clinical follow-up. Bone quality, bone resorption, implant stability, and oral health were assessed radiographically. A total of 32 participants with edentulism were included. Twenty-two participants (99 implants) received 4 to 5 mini-dental implants (diameter: 1.8-2.4 mm; length: 13-15 mm, study group), and 10 participants (35 implants) received 2 to 4 conventional dental implants (diameter: 3.3-3.7 mm; length: 11-13 mm, control group). The selection of the participants in the study or control group was based on the available bone volume in the mandible. The selection was not randomized. The density of cortical bone thickness was measured in Hounsfield units (HU) from computed tomography data, and patients were followed for 2 years. The participants were examined 3, 6, 12, and 24 months after surgery. Primary stability immediately after the insertion of dental implants (Periotest), secondary stability 6 months after implantation, modified plaque, bleeding on probing indices, and probing depth were measured and analyzed statistically (α=.05). The mean HU value 6 months after implantation in the participants who received mini-dental implants was significantly (P=.035) higher (1250 HU) than that in the participants who received conventional dental implants (1100 HU). The probing depths around the conventional dental implants (1.6 and 1.8 mm, respectively) were significantly higher than those around the mini-dental implants (1.3 and 1.2 mm, respectively) 12 and 24 months after surgery, respectively (P<.001). The mean primary and secondary stability values for conventional dental implants were -4.0 and -4.9, respectively. The primary and secondary stability values for the mini-dental implants were -0.3 and -1.4, respectively. The Periotest values of the primary (measured immediately after implant insertion) and secondary implant stabilities (measured 6 months after implant insertion) were significantly higher for the conventional dental implants than for the mini-dental implants (P<.001). Based on this 2-year clinical trial, patients receiving mini-dental implants had clinical outcomes similar to those of patients receiving conventional dental implants to support overdenture prostheses. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Comparison of Three Biomass Sampling Techniques on Submersed Aquatic Plants in a Northern Tier Lake

DTIC Science & Technology

2010-07-01

distribution in 3 out of 14 species when comparing the box-core sampler and the rake method. These included forked duckweed (Lemna trisulca L, p...each site did not exhibit differences. These included coontail (p=0.2949), muskgrass (p=0.2746), American elodea (p=0.7622), forked duckweed (p...collected by the PVC-core sampler. These included coontail (p=0.000), chara (p=0.0219), American elodea (p=0.0061), forked duckweed (p=0.0000), najas (p

Measurements in Regions of Shock Wave/Turbulent Boundary Layer Interaction from Mach 3 to 10 for Open and Blind Code Evaluation/Validation

DTIC Science & Technology

2013-03-01

rakes containing pitot pressure probes, stagnation heat transfer gauges on hemispherical cylinders, total temperature measurements with vented...defined configurations in both “true temperature” and “cold” supersonic and hypersonic flows with boundary and flow conditions to provide the basis for...conducted over the past 50 years to provide data on both wedge- and shock- induced turbulent separated regions in supersonic and hypersonic flows suffer from

Pre-Flight Ground Testing of the Full-Scale HIFiRE-1 Vehicle at Fully Duplicated Flight Conditions: Part 2

DTIC Science & Technology

2008-05-14

survey rake installed in the test section to measure pitot pressure, static pressure and stagnation point heat transfer in the freestream. From these...on the cone, employing time of arrival pressure transducers to obtain 2"d mode transition frequencies, and making pitot pressure measurements to...these studies have proven to be the most accurate measurement technique in supersonic and hypersonic test facilities, and the small size of the sensing

Wind Tunnel Results from a Nozzle Afterbody Test of A 0.1-Scale Fighter Aircraft in the Mach Number Regime of 0.6 to 1.6

DTIC Science & Technology

1978-06-01

25 4. Nose Strake and Pitot Boom Details . . . . . . . . . . . . . . . . . . . . . . 28 5. Exhaust Nozzle Closure...actual wing through the use of simulated wing gloves (Fig. 3c) which duplicated the modification required on the wingtip supported model. The pitot ...pressure rakes located in the model plenum upstream of the nozzle throat were used to monitor the simulated jet flow. 2.2.5 Surface Pressures

Evaluation of a Wedge on a Force Balance as a Flow Angle Probe

DTIC Science & Technology

1975-02-01

pitot rake attached to the Captive Trajectory System (CTS), and (3) measurement of flow angles in the same region with a probe attached to the CTS...localized pressures. Although it was the characteristics of supersonic flow which led to this conclusion, and even though the wedge design was based...vary the open area from near zero to 10 percent. Suction through the porous walls is used to maximize flow uniformity and to develop supersonic flow

Modeling of thermal processes arising during shaping gears with internal non-involute teeth

NASA Astrophysics Data System (ADS)

Kanatnikov, N. V.; Kanatnikova, P. A.; Vlasov, V. V.; Pashmentova, A. S.

2018-03-01

The paper presents a model for predicting the thermal processes arising during shaping gears with internal non-involute teeth. The kinematics of cutting is modeled due to the analytical model. Chipping is modeled using the finite element method. The experiment is based on the method of infrared photography of the cutting process. The simulation results showed that the maximum temperatures and heat flows in the tool vary by more than 10% when the rake and clearance angels of the cutting are changed.

Long-term Outcomes of Hypofractionation Versus Conventional Radiation Therapy After Breast-Conserving Surgery for Ductal Carcinoma In Situ of the Breast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lalani, Nafisha; Paszat, Lawrence; Department of Radiation Oncology, Sunnybrook Health Sciences Centre, Toronto, Ontario

Purpose: Whole-breast radiation therapy (XRT) after breast-conserving surgery (BCS) for ductal carcinoma in situ (DCIS) may decrease the risk of local recurrence, but the optimal dose regimen remains unclear. Past studies administered 50 Gy in 25 fractions (conventional); however, treatment pattern studies report that hypofractionated (HF) regimens (42.4 Gy in 16 fractions) are frequently used. We report the impact of HF (vs conventional) on the risk of local recurrence after BCS for DCIS. Methods and Materials: All women with DCIS treated with BCS and XRT in Ontario, Canada from 1994 to 2003 were identified. Treatment and outcomes were assessed through administrative databasesmore » and validated by chart review. Survival analyses were performed. To account for systematic differences between women treated with alternate regimens, we used a propensity score adjustment approach. Results: We identified 1609 women, of whom 971 (60%) received conventional regimens and 638 (40%) received HF. A total of 489 patients (30%) received a boost dose, of whom 143 (15%) received conventional radiation therapy and 346 (54%) received HF. The median follow-up time was 9.2 years. The median age at diagnosis was 56 years (interquartile range [IQR], 49-65 years). On univariate analyses, the 10-year actuarial local recurrence–free survival was 86% for conventional radiation therapy and 89% for HF (P=.03). On multivariable analyses, age <45 years (hazard ratio [HR] = 2.4; 95% CI: 1.6-3.4; P<.0001), high (HR=2.9; 95% CI: 1.2-7.3; P=.02) or intermediate nuclear grade (HR=2.7; 95% CI: 1.1-6.6; P=.04), and positive resection margins (HR=1.4; 95% CI: 1.0-2.1; P=.05) were associated with an increased risk of local recurrence. HF was not significantly associated with an increased risk of local recurrence compared with conventional radiation therapy on multivariate analysis (HR=0.8; 95% CI: 0.5-1.2; P=.34). Conclusions: The risk of local recurrence among individuals treated with HF regimens after BCS for DCIS was similar to that among individuals treated with conventional radiation therapy.« less

Severe Hepatic Sinusoidal Obstruction Syndrome in a Child Receiving Vincristine, Actinomycin-D, and Cyclophosphamide for Rhabdomyosarcoma: Successful Treatment with Defibrotide.

PubMed

Choi, Aery; Kang, Young Kyung; Lim, Sewon; Kim, Dong Ho; Lim, Jung Sub; Lee, Jun Ah

2016-10-01

Hepatic sinusoidal obstruction syndrome (SOS) is a life-threatening syndrome that generally occurs as a complication after hematopoietic stem cell transplantation or, less commonly, after conventional chemotherapy. Regarding SOS in rhabdomyosarcoma patients who received conventional chemotherapy, the doses of chemotherapeutic agents are associated with the development of SOS. Several cases of SOS in rhabdomyosarcoma patients after receiving chemotherapy with escalated doses of cyclophosphamide have been reported. Here, we report on a 9-year-old female with rhabdomyosarcoma who developed severe SOS after receiving chemotherapy consisting of vincristine, actinomycin-D, and a moderate dose of cyclophosphamide. She was treated successfully with defibrotide without sequelae to the liver.

Lower conjunctival fornix packing for mydriasis in premature infants: a randomized trial

PubMed Central

Thanathanee, Onsiri; Ratanapakorn, Tanapat; Morley, Michael G; Yospaiboon, Yosanan

2012-01-01

Objective To compare the mydriatic effect of lower conjunctival fornix packing to conventional instillation of eyedrops containing 2.5% phenylephrine and 1% tropicamide in premature infants undergoing examination for retinopathy of prematurity. Methods The patients were randomized to receive either conventional instillation of mydriatic drops or lower conjunctival fornix packing in one eye and the alternate method in the fellow eye. For the eyes receiving lower conjunctival fornix packing (study group), one small piece of the cotton wool soaked with one drop of 2.5% phenylephrine and one drop of 1% tropicamide was packed in the lower conjunctival fornix for 15 minutes. For the eyes receiving the conventional instillation (control group), 2.5% phenylephrine and 1% tropicamide were alternately instilled every 5 minutes for two doses each. Horizontal pupil diameter was measured with a ruler in millimeters 40 minutes later. Results The mean dilated pupil diameter in study group and control group were 5.76 ± 1.01 mm and 4.50 ± 1.08 mm, respectively. This difference was statistically significant (P < 0.05). Conclusion The dilated pupil diameter after receiving the lower conjunctival fornix packing was larger than conventional instillation with a statistically significant difference. We recommended the packing method to dilate the preterm infant pupil, especially if the pupil is difficult to dilate. PMID:22368443

Survival time of dogs with splenic hemangiosarcoma treated by splenectomy with or without adjuvant chemotherapy: 208 cases (2001-2012).

PubMed

Wendelburg, Kristin M; Price, Lori Lyn; Burgess, Kristine E; Lyons, Jeremiah A; Lew, Felicia H; Berg, John

2015-08-15

To determine survival time for dogs with splenic hemangiosarcoma treated with splenectomy alone, identify potential prognostic factors, and evaluate the efficacy of adjuvant chemotherapy. Retrospective case series. 208 dogs. Medical records were reviewed, long-term follow-up information was obtained, and survival data were analyzed statistically. 154 dogs were treated with surgery alone, and 54 were treated with surgery and chemotherapy. Twenty-eight dogs received conventional chemotherapy, 13 received cyclophosphamide-based metronomic chemotherapy, and 13 received both conventional and metronomic chemotherapy. Median survival time of dogs treated with splenectomy alone was 1.6 months. Clinical stage was the only prognostic factor significantly associated with survival time. When the entire follow-up period was considered, there was no significant difference in survival time between dogs treated with surgery alone and dogs treated with surgery and chemotherapy. However, during the first 4 months of follow-up, after adjusting for the effects of clinical stage, survival time was significantly prolonged among dogs receiving any type of chemotherapy (hazard ratio, 0.6) and among dogs receiving both conventional and metronomic chemotherapy (hazard ratio, 0.4). Clinical stage was strongly associated with prognosis for dogs with splenic hemangiosarcoma. Chemotherapy was effective in prolonging survival time during the early portion of the follow-up period. Combinations of doxorubicin-based conventional protocols and cyclophosphamide-based metronomic protocols appeared to be more effective than either type of chemotherapy alone, but prolongations in survival time resulting from current protocols were modest.

Timing Recovery Strategies in Magnetic Recording Systems

NASA Astrophysics Data System (ADS)

Kovintavewat, Piya

At some point in a digital communications receiver, the received analog signal must be sampled. Good performance requires that these samples be taken at the right times. The process of synchronizing the sampler with the received analog waveform is known as timing recovery. Conventional timing recovery techniques perform well only when operating at high signal-to-noise ratio (SNR). Nonetheless, iterative error-control codes allow reliable communication at very low SNR, where conventional techniques fail. This paper provides a detailed review on the timing recovery strategies based on per-survivor processing (PSP) that are capable of working at low SNR. We also investigate their performance in magnetic recording systems because magnetic recording is a primary method of storage for a variety of applications, including desktop, mobile, and server systems. Results indicate that the timing recovery strategies based on PSP perform better than the conventional ones and are thus worth being employed in magnetic recording systems.

Severe Hepatic Sinusoidal Obstruction Syndrome in a Child Receiving Vincristine, Actinomycin-D, and Cyclophosphamide for Rhabdomyosarcoma: Successful Treatment with Defibrotide

PubMed Central

Choi, Aery; Kang, Young Kyung; Lim, Sewon; Kim, Dong Ho; Lim, Jung Sub; Lee, Jun Ah

2016-01-01

Hepatic sinusoidal obstruction syndrome (SOS) is a life-threatening syndrome that generally occurs as a complication after hematopoietic stem cell transplantation or, less commonly, after conventional chemotherapy. Regarding SOS in rhabdomyosarcoma patients who received conventional chemotherapy, the doses of chemotherapeutic agents are associated with the development of SOS. Several cases of SOS in rhabdomyosarcoma patients after receiving chemotherapy with escalated doses of cyclophosphamide have been reported. Here, we report on a 9-year-old female with rhabdomyosarcoma who developed severe SOS after receiving chemotherapy consisting of vincristine, actinomycin-D, and a moderate dose of cyclophosphamide. She was treated successfully with defibrotide without sequelae to the liver. PMID:27034141

Diagnostic developments for velocity and temperature measurements in uni-element rocket environments

NASA Astrophysics Data System (ADS)

Philippart, Kenneth D.

1995-08-01

Velocity and temperature measurements were taken within a uni-element rocket combustion chamber for hydrogen-oxygen propellants using laser Doppler velocimetry, thermocouples, and a thermocouple-based temperature rake developed for this effort. Velocity and turbulence profiles were obtained for firings with a gaseous oxygen (GO2)/gaseous hydrogen (GH2) coaxial shear injector at axial locations of 1.6 mm (0.063 in.), 6.4 mm (0.25 in.), 12.7 mm (0.5 in.), 25.4 mm (1 in.) and 50.8 mm (2 in.). Aluminum oxide particles of various sizes seeded the flow in an attempt to explain the discrepancies. While cold-flow simulations were promising, hot-fire results for the various particles were virtually identical and still lower than earlier data. The hot-firings were self-consistent and question the reproducibility of the previous data. Velocity measurements were made closer to the injector than the preceding work. Asymmetries were noted in all profiles. The shear layer displayed high turbulence levels. The central flow near the injector resembled turbulent pipe flow. Recirculation zones existed at the chamber walls and became smaller as the flow evolved downstream. The combusting flow region expanded with increasing axial distance. A thermocouple-instrumented coaxial injector was fired with GO2/GH2 propellants. The injector exit plane boundary conditions were determined. The feasibility of a thermocouple-based temperature rake was established. Tests at three axial positions for air/GM2 firings revealed asymmetric profiles. Temperatures increased with increasing axial distance.

Macrophyte monitoring along the Trentino side of the Lake Garda

NASA Astrophysics Data System (ADS)

Pellegrini, Giovanna; Monauni, Catia; Fedrizzi, Fabio; Laura, Fravezzi; Paola, Testa; Silvia, Costaraoss; Mario, Mazzurana; Gaetano, Patti; Barbara, Zennaro

2013-04-01

Macrophytes, that grow along the Trentino shorezone of the Lake Garda, were sampled and mapped during summer 2010. The sampling protocol foresees a lake bottom survey until the depth of 15 using GPS system, for identifying sampling sites and transects, waterproof camcorder, batiscope and a rake. The proof of 13/14 meters is the internal limit for macrophyte development. The area between 6 and 13/14 meters was surveyed with a robot camcorder placed on a boat of the fireworks brigade of Trento. This boat was used to track the 14 km of the shorezone of the Trentino part of the Lake Garda. The investigation result is a survey of a wide carex prairie that has no interruption all along the lake perimeter. An inflatable boat was used to inspect the shorezone using a batiscope. The macrophyte samples were collected using a rake. The number of mapped sites is 15, transects are 15 and identified 18 different species. During 2011, in conjunction with the flight MIVIS within the EULAKES project, the macrophyte distribution was confirmed and further inspection was carried out for sampling and classifying caracee. Among the species collected, Chara globularis was present in all sites sampled, while sites 0 and 12, corresponding respectively to local reserve Val Gola and the bay of Torbole, showed the highest biodiversity among sites, with 11 species collected of the 18 total. Within each site, higher number of species were collected between 2 and 5 meters depth's.

Side Flow Effect on Surface Generation in Nano Cutting

NASA Astrophysics Data System (ADS)

Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

2017-05-01

The side flow of material in nano cutting is one of the most important factors that deteriorate the machined surface quality. The effects of the crystallographic orientation, feed, and the cutting tool geometry, including tool edge radius, rake angle and inclination angle, on the side flow are investigated employing molecular dynamics simulation. The results show that the stagnation region is formed in front of tool edge and it is characterized by the stagnation radius R s and stagnation height h s . The side flow is formed because the material at or under the stagnation region is extruded by the tool edge to flow to the side of the tool edge. Higher stagnation height would increase the size of the side flow. The anisotropic nature of the material which partly determines the stagnation region also influences the side flow due to the different deformation mechanism under the action of the tool edge. At different cutting directions, the size of the side flow has a great difference which would finally affect the machined surface quality. The cutting directions of {100} < 011>, {110} < 001>, and {110} < 1-10 > are beneficial to obtain a better surface quality with small side flow. Besides that, the side flow could be suppressed by reducing the feed and optimizing the cutting tool geometry. Cutting tool with small edge radius, large positive rake angle, and inclination angle would decrease the side flow and consequently improve the machined surface quality.

Side Flow Effect on Surface Generation in Nano Cutting.

PubMed

Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

2017-12-01

The side flow of material in nano cutting is one of the most important factors that deteriorate the machined surface quality. The effects of the crystallographic orientation, feed, and the cutting tool geometry, including tool edge radius, rake angle and inclination angle, on the side flow are investigated employing molecular dynamics simulation. The results show that the stagnation region is formed in front of tool edge and it is characterized by the stagnation radius R s and stagnation height h s . The side flow is formed because the material at or under the stagnation region is extruded by the tool edge to flow to the side of the tool edge. Higher stagnation height would increase the size of the side flow. The anisotropic nature of the material which partly determines the stagnation region also influences the side flow due to the different deformation mechanism under the action of the tool edge. At different cutting directions, the size of the side flow has a great difference which would finally affect the machined surface quality. The cutting directions of {100} < 011>, {110} < 001>, and {110} < 1-10 > are beneficial to obtain a better surface quality with small side flow. Besides that, the side flow could be suppressed by reducing the feed and optimizing the cutting tool geometry. Cutting tool with small edge radius, large positive rake angle, and inclination angle would decrease the side flow and consequently improve the machined surface quality.

Faulting Parameters of the January 16, 1994 Wyomissing Hills, Pennsylvania Earthquakes

USGS Publications Warehouse

Ammon, C.J.; Herrmann, Robert B.; Langston, C.A.; Benz, H.

1998-01-01

Two events dominated the January 1994, Wyomissing, PA earthquake sequence, an Mw 4.0 foreshock, followed by an Mw 4.6 mainshock. We modeled regional waveforms to estimate the event depth and the moment tensors for the two largest events in the sequence, and examine teleseismic wave-forms recorded on the ARCESS short-period seismic array to estimate the depth and source time function of the mainshock. Our data constrain the depth of the events to be shallower than 5 km, and prefer a depth of 3-5 km. For an assumed depth of 3 km, the mainshock moment tensor is 75% double couple, with (the major double couple) planes striking at 135??N, 347??N, dips of 49??, 46??, and rakes of 68??, 114??. The estimated moment is 8.9 ?? 1022 dyne-cm. The P axis strikes 241??N and plunges 2??, the Tension axis strikes 336??N and plunges 73??. The foreshock inversion results are virtually identical to the mainshock results; for a source depth of three km, we find a major double couple with a strike, dip, and rake of 121??N, 60??, and 66??, respectively. The seismic moment for the foreshock is 1.2 ?? 1022 dyne-cm, which is approximately 13% of the mainshock moment release. These events did not excite high-frequency Lg waves as effectively as typical eastern North American events, and the mainshock had a stress drop in the range of 25-50 bars.

Sumatran orangutans differ in their cultural knowledge but not in their cognitive abilities.

PubMed

Gruber, Thibaud; Singleton, Ian; van Schaik, Carel

2012-12-04

Animal cultures are controversial because the method used to isolate culture in animals aims at excluding genetic and environmental influences rather than demonstrating social learning. Here, we analyzed these factors in parallel in captivity to determine their influences on tool use. We exposed Sumatran orangutan (Pongo abelii) orphans from tool-using and non-tool-using regions (western swamps and eastern Langkat, respectively) that differed in both genetic and cultural backgrounds to a raking task and a honey-dipping task to assess their understanding of stick use. Orangutans from both regions were equally successful in raking; however, swamp orangutans were more successful than Langkat orangutans in honey dipping, where previously acquired knowledge was required. A larger analysis suggested that the Alas River could constitute a geographical barrier to the spread of this cultural trait. Finally, honey-dipping individuals were on average less than 4 years old, but this behavior is not observed in the wild before 6 years of age. Our results suggest first that genetic differences between wild Sumatran populations cannot explain their differences in stick use; however, their performances in honey dipping support a cultural differentiation in stick knowledge. Second, the results suggest that the honey-dippers were too young when arriving at the quarantine center to have possibly mastered the behavior in the wild individually, suggesting that they arrived with preestablished mental representations of stick use or, simply put, "cultural ideas." Copyright © 2012 Elsevier Ltd. All rights reserved.

New tool holder design for cryogenic machining of Ti6Al4V

NASA Astrophysics Data System (ADS)

Bellin, Marco; Sartori, Stefano; Ghiotti, Andrea; Bruschi, Stefania

2017-10-01

The renewed demand of increasing the machinability of the Ti6Al4V titanium alloy to produce biomedical and aerospace parts working at high temperature has recently led to the application of low-temperature coolants instead of conventional cutting fluids to increase both the tool life and the machined surface integrity. In particular, the liquid nitrogen directed to the tool rake face has shown a great capability of reducing the temperature at the chip-tool interface, as well as the chemical interaction between the tool coating and the titanium to be machined, therefore limiting the tool crater wear, and improving, at the same time, the chip breakability. Furthermore, the nitrogen is a safe, non-harmful, non-corrosive, odorless, recyclable, non-polluting and abundant gas, characteristics that further qualify it as an environmental friendly coolant to be applied to machining processes. However, the behavior of the system composed by the tool and the tool holder, exposed to the cryogenics temperatures may represent a critical issue in order to obtain components within the required geometrical tolerances. On this basis, the paper aims at presenting the design of an innovative tool holder installed on a CNC lathe, which includes the cryogenic coolant provision system, and which is able to hinder the part possible distortions due to the liquid nitrogen adduction by stabilizing its dimensions through the use of heating cartridges and appropriate sensors to monitor the temperature evolution of the tool holder.

Investigation of the Effect of Tool Edge Geometry upon Cutting Variables, Tool Wear and Burr Formation Using Finite Element Simulation — A Progress Report

NASA Astrophysics Data System (ADS)

Sartkulvanich, Partchapol; Al-Zkeri, Ibrahim; Yen, Yung-Chang; Altan, Taylan

2004-06-01

This paper summarizes some of the progress made on FEM simulations of metal cutting processes conducted at the Engineering Research Center (ERC/NSM). Presented research focuses on the performance of various cutting edge geometries (hone and chamfer edges) for different tool materials and specifically on: 1) the effect of round and chamfer edge geometries on the cutting variables in machining carbon steels and 2) the effect of the edge hone size upon the flank wear and burr formation behavior in face milling of A356-T6 aluminum alloy. In the second task, an innovative design of edge preparation with varying hone size around the tool nose is also explored using FEM. In order to model three-dimensional conventional turning and face milling with two-dimensional orthogonal cutting simulations, 2D simulation cross-sections consisting of the cutting speed direction and chip flow direction are selected at different locations along the tool nose radius. Then the geometries of the hone and chamfer edges and their associated tool angles as well as uncut chip thickness are determined on these planes and employed in cutting simulations. The chip flow direction on the tool rake face are obtained by examining the wear grooves on the experimental inserts or estimated by using Oxley's approximation theory of oblique cutting. Simulation results are compared with the available experimental results (e.g. cutting forces) both qualitatively and quantitatively.

Analyzing the effect of tool edge radius on cutting temperature in micro-milling process

NASA Astrophysics Data System (ADS)

Liang, Y. C.; Yang, K.; Zheng, K. N.; Bai, Q. S.; Chen, W. Q.; Sun, G. Y.

2010-10-01

Cutting heat is one of the important physical subjects in the cutting process. Cutting heat together with cutting temperature produced by the cutting process will directly have effects on the tool wear and the life as well as on the workpiece processing precision and surface quality. The feature size of the workpiece is usually several microns. Thus, the tiny changes of cutting temperature will affect the workpiece on the surface quality and accuracy. Therefore, cutting heat and temperature generated in micro-milling will have significantly different effect than the one in the traditional tools cutting. In this paper, a two-dimensional coupled thermal-mechanical finite element model is adopted to determine thermal fields and cutting temperature during the Micro-milling process, by using software Deform-2D. The effect of tool edge radius on effective stress, effective strain, velocity field and cutting temperature distribution in micro-milling of aluminum alloy Al2024-T6 were investigated and analyzed. Also, the transient cutting temperature distribution was simulated dynamically. The simulation results show that the cutting temperature in Micro-milling is lower than those occurring in conventional milling processes due to the small loads and low cutting velocity. With increase of tool edge radius, the maximum temperature region gradually occurs on the contact region between finished surfaced and flank face of micro-cutter, instead of the rake face or the corner of micro-cutter. And this phenomenon shows an obvious size effect.

Radar, target and ranging

NASA Astrophysics Data System (ADS)

1984-09-01

This Test Operations Procedure (TOP) provides conventional test methods employing conventional test instrumentation for testing conventional radars. Single tests and subtests designed to test radar components, transmitters, receivers, antennas, etc., and system performance are conducted with single item instruments such as meters, generators, attenuators, counters, oscillators, plotters, etc., and with adequate land areas for conducting field tests.

The effect of mandibular 2-implant overdentures on oral health-related quality of life: an international multicentre study.

PubMed

Awad, Manal A; Rashid, Faahim; Feine, Jocelyne S

2014-01-01

To determine the difference in oral health-related quality of life (OHRQoL) in patients who received mandibular 2-implant overdentures and conventional dentures in a pragmatic international study. In this prospective study, data were gathered from 203 edentulous patients (mean age, 68.8; SD: 10.4 years) at eight centres in North America, South America and Europe. The patients were provided with new mandibular conventional dentures or implant overdentures supported by 2 implants and ball attachments and opposed by conventional dentures. At baseline and at 6 months post-treatment, patients rated their oral health-related quality of life using the OHIP-20. A significantly higher proportion of the participants in the implant group in North America reported improvement in both the psychological and the handicap domains, compared to those who received conventional dentures (93% vs. 52%; P < 0.05). In South America, 100% of participants who received implant overdentures reported improvement in physical pain, compared to 66% in the conventional group (P < 0.05). Differences in mean change scores among those who expressed improvement were not significantly different between sites or treatments. Mandibular 2-implant overdentures are more likely than conventional dentures to improve OHRQL for edentulous patients. Cultural differences were also observed in the impact of implant overdentures on the different domains of the OHIP-20. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Impact of conventional or intensive milk replacer programs on Holstein heifer performance through six months of age and during first lactation.

PubMed

Raeth-Knight, M; Chester-Jones, H; Hayes, S; Linn, J; Larson, R; Ziegler, D; Ziegler, B; Broadwater, N

2009-02-01

The objectives were to evaluate the impact of conventional or intensive milk replacer (MR) feeding programs on heifer calf performance through 6 mo of age, age at first calving, and first lactation performance. At 3 (+/-1 d) d of age, 133 Holstein heifer calves from 3 commercial dairy farms were randomly assigned, within calf source, to a conventional [20% crude protein (CP), 20% fat] or intensive MR (28% CP, 18% fat). Milk replacer treatments and percent solids were 1) conventional nonacidified (CNA), 13.9%; 2) conventional acidified (CA), 13.9%; 3) modified intensive high solids (IHS), 16.7%; 4) modified intensive low solids (ILS), 12.5%; and 5) intensive high solids, high feeding (IHSHF), 16.7%. Calves were individually housed and remained on trial for 56 d. At 2 mo of age, heifers were grouped in pens by treatment with 6 heifers per pen (4 pens per treatment). An 18.1% CP grower concentrate mix (dry matter basis) was fed to heifers that received a conventional MR and a 21.2% CP grower concentrate mix was fed to heifers that received the intensive MR preweaning. Heifers were offered 2.45 kg/d (dry matter basis) of their respective grower concentrate mix for 112 d plus free access to hay and water. At approximately 24 wk of age, heifers were transported to a second-stage grower before returning to their respective farms approximately 1 mo before calving. First-lactation performance was determined using Dairy Herd Improvement Association records. The IHSHF treatment resulted in increased calf body weight and hip height during the preweaning and early postweaning (PEP) period and the postweaning heifer grower (PHG) period as compared with the conventional (CNA and CA) or modified intensive MR treatments (IHS and ILS). Calves receiving the IHS treatment were heavier at d 56 of the PEP period compared with the conventional or ILS treatments; however, this growth advantage was not maintained in the PHG period. Feed cost per kilogram of gain during the PEP period was lowest for CNA and CA, intermediate for IHS and ILS, and highest for the IHSHF treatment. There was no effect of MR feeding program on first-lactation performance; however, heifers that received the IHSHF MR preweaning calved 27.5 d earlier than those fed a conventional MR.

The effect of different physiotherapy interventions in post-BTX-A treatment of children with cerebral palsy.

PubMed

Desloovere, K; De Cat, J; Molenaers, G; Franki, I; Himpens, E; Van Waelvelde, H; Fagard, K; Van den Broeck, C

2012-01-01

To distinguish the effects of different physiotherapeutic programs in a post BTX-A regime for children with Cerebral Palsy (CP). Retrospective, controlled intervention study. A group of 38 children (X¯ = 7y7m, GMFCS I-III, 27 bilateral, 11 unilateral CP) receiving an individually defined Neurodevelopment Treatment (NDT) program, was matched and compared to a group of children with the same age, GMFCS and diagnosis, receiving more conventional physiotherapy treatment. All patients received selective tone-reduction by means of multilevel BTX-A injections and adequate follow-up treatment, including physiotherapy. Three-dimensional gait analyses and clinical examination was performed pre and two months post-injection. Treatment success was defined using the Goal Attainment Scale (GAS). Both groups' mean converted GAS scores were above 50. The average converted GAS score was higher in the group of children receiving NDT than in the group receiving conventional physiotherapy (p < 0.05). In the NDT group, overall treatment success was achieved in 76% of the goals, compared to 67% of the goals defined for the conventional physiotherapy group. Especially for the goals based on gait analyses (p < 0.05) and in the group of children with bilateral CP (p < 0.05), treatment success was higher in the NDT group. In a post-BTX-A regime, the short-term effects of an NDT approach are more pronouncedthan these from a conventional physiotherapy approach. Copyright © 2011 European Paediatric Neurology Society. Published by Elsevier Ltd. All rights reserved.

Kramers-Kronig receiver operable without digital upsampling.

PubMed

Bo, Tianwai; Kim, Hoon

2018-05-28

The Kramers-Kronig (KK) receiver is capable of retrieving the phase information of optical single-sideband (SSB) signal from the optical intensity when the optical signal satisfies the minimum phase condition. Thus, it is possible to direct-detect the optical SSB signal without suffering from the signal-signal beat interference and linear transmission impairments. However, due to the spectral broadening induced by nonlinear operations in the conventional KK algorithm, it is necessary to employ the digital upsampling at the beginning of the digital signal processing (DSP). The increased number of samples at the DSP would hinder the real-time implementation of this attractive receiver. Hence, we propose a new DSP algorithm for KK receiver operable at 2 samples per symbol. We adopt a couple of mathematical approximations to avoid the use of nonlinear operations such as logarithm and exponential functions. By using the proposed algorithm, we demonstrate the transmission of 112-Gb/s SSB orthogonal frequency-division-multiplexed signal over an 80-km fiber link. The results show that the proposed algorithm operating at 2 samples per symbol exhibits similar performance to the conventional KK one operating at 6 samples per symbol. We also present the error analysis of the proposed algorithm for KK receiver in comparison with the conventional one.

Rotating hot-wire investigation of the vortex responsible for blade-vortex interaction noise

NASA Technical Reports Server (NTRS)

Fontana, Richard Remo

1988-01-01

This distribution of the circumferential velocity of the vortex responsible for blade-vortex interaction noise was measured using a rotating hot-wire rake synchronously meshed with a model helicopter rotor at the blade passage frequency. Simultaneous far-field acoustic data and blade differential pressure measurements were obtained. Results show that the shape of the measured far-field acoustic blade-vortex interaction signature depends on the blade-vortex interaction geometry. The experimental results are compared with the Widnall-Wolf model for blade-vortex interaction noise.

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER “HOT SHOT” ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-4 FOR IDENTICAL B&W NEGATIVE. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTH ELEVATION OF GOLD HILL MILL, LOOKING SOUTH. AT LEFT EDGE IS THE SINGLE CYLINDER “HOT SHOT” ENGINE THAT PROVIDED POWER FOR THE MILL. JUST IN FRONT OF IT IS AN ARRASTRA. AT CENTER IS THE BALL MILL AND SECONDARY ORE BIN. JUST TO THE RIGHT OF THE BALL MILL IS A RAKE CLASSIFIER, AND TO THE RIGHT ARE THE CONCENTRATION TABLES. WARM SPRINGS CAMP IS IN THE DISTANCE. SEE CA-292-17 (CT) FOR IDENTICAL COLOR TRANSPARENCY. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

Advanced Noise Control Fan: A 20-Year Retrospective

NASA Technical Reports Server (NTRS)

Sutliff, Dan

2016-01-01

The ANCF test bed is used for evaluating fan noise reduction concepts, developing noise measurement technologies, and providing a database for Aero-acoustic code development. Rig Capabilities: 4 foot 16 bladed rotor @ 2500 rpm, Auxiliary air delivery system (3 lbm/sec @ 6/12 psi), Variable configuration (rotor pitch angle, stator count/position, duct length), synthetic acoustic noise generation (tone/broadband). Measurement Capabilities: 112 channels dynamic data system, Unique rotating rake mode measuremen, Farfield (variable radius), Duct wall microphones, Stator vane microphones, Two component CTA w/ traversing, ESP for static pressures.

A Mode Propagation Database Suitable for Code Validation Utilizing the NASA Glenn Advanced Noise Control Fan and Artificial Sources

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2014-01-01

The NASA Glenn Research Center's Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. A series of tests were performed primarily for the use of code validation and tool validation. Rotating Rake mode measurements were acquired for parametric sets of: (i) mode blockage, (ii) liner insertion loss, (iii) short ducts, and (iv) mode reflection.

A Mode Propagation Database Suitable for Code Validation Utilizing the NASA Glenn Advanced Noise Control Fan and Artificial Sources

NASA Technical Reports Server (NTRS)

Sutliff, Daniel L.

2014-01-01

The NASA Glenn Research Center's Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. A series of tests were performed primarily for the use of code validation and tool validation. Rotating Rake mode measurements were acquired for parametric sets of: (1) mode blockage, (2) liner insertion loss, (3) short ducts, and (4) mode reflection.

Geometerial description for a proposed aeroassist flight experiment vehicle

NASA Technical Reports Server (NTRS)

Cheatwood, F. M.; Dejarnette, F. J.; Hamilton, H. H., II

1986-01-01

One geometry currently under consideration for the Aeroassist Flight Experiment (AFE) vehicle is composed of several segments of simple general conics: an ellipsoidal nose tangent to an elliptical cone and a base skirt with the base plane raked relative to the body axis. An analytic representation for the body coordinates and first and second partial derivatives of this configuration has been developed. Equations are given which define the body radius and partial derivatives for a prescribed axial and circumferential position on the vehicle. The results for a sample case are tabulated and presented graphically.

Improvement of diagnostic efficiency in distinguishing the benign and malignant thyroid nodules via conventional ultrasound combined with ultrasound contrast and elastography

PubMed Central

Liu, Mei-Juan; Men, Yan-Ming; Zhang, Yong-Lin; Zhang, Yu-Xi; Liu, Hao

2017-01-01

We aimed to evaluate the diagnostic values of conventional ultrasound (US), ultrasound contrast (UC) and ultrasound elastography (UE) in distinguishing the benign and malignant thyroid nodules. A total of 100 patients with thyroid nodules receiving operative treatment were selected; they underwent the conventional US, UE and UC examinations before operation, respectively. The nodules received pathological examination after operation to distinguish benign from malignant lesions. The sensitivity, specificity and diagnostic accordance rate of each diagnostic method was evaluated by receiver operating characteristic (ROC) curve, and the area under the curve (AUC) of ROC was calculated. The manifestations of malignant thyroid nodules in conventional US examination were mostly the hypoecho, heterogeneous echo, irregular shape, unclear boundary, aspect ratio <1, microcalcification and irregular peripheral echo halo, and there were statistically significant differences compared with the benign nodules (P<0.05). UE showed that the differences between benign and malignant nodules in 2, 3 and 4 points were statistically significant (P<0.05). The manifestations of malignant nodules in UC were mostly the irregular shape, obscure boundary, no obvious enhancement, heterogeneous enhancement and visible perfusion defects, and there were statistically significant differences compared with the benign nodules (P<0.05). ROC curve showed that both sensitivity and specificity of UE and UC were superior to those of conventional US. AUC was the largest (AUC = 0.908) and the diagnostic value was the highest in the conventional US combined with UE and UC. Conventional US combined with elastography and UC can significantly improve the sensitivity, specificity and accuracy of diagnosis of benign and malignant thyroid nodules. PMID:28693244

Improvement of diagnostic efficiency in distinguishing the benign and malignant thyroid nodules via conventional ultrasound combined with ultrasound contrast and elastography.

PubMed

Liu, Mei-Juan; Men, Yan-Ming; Zhang, Yong-Lin; Zhang, Yu-Xi; Liu, Hao

2017-07-01

We aimed to evaluate the diagnostic values of conventional ultrasound (US), ultrasound contrast (UC) and ultrasound elastography (UE) in distinguishing the benign and malignant thyroid nodules. A total of 100 patients with thyroid nodules receiving operative treatment were selected; they underwent the conventional US, UE and UC examinations before operation, respectively. The nodules received pathological examination after operation to distinguish benign from malignant lesions. The sensitivity, specificity and diagnostic accordance rate of each diagnostic method was evaluated by receiver operating characteristic (ROC) curve, and the area under the curve (AUC) of ROC was calculated. The manifestations of malignant thyroid nodules in conventional US examination were mostly the hypoecho, heterogeneous echo, irregular shape, unclear boundary, aspect ratio <1, microcalcification and irregular peripheral echo halo, and there were statistically significant differences compared with the benign nodules (P<0.05). UE showed that the differences between benign and malignant nodules in 2, 3 and 4 points were statistically significant (P<0.05). The manifestations of malignant nodules in UC were mostly the irregular shape, obscure boundary, no obvious enhancement, heterogeneous enhancement and visible perfusion defects, and there were statistically significant differences compared with the benign nodules (P<0.05). ROC curve showed that both sensitivity and specificity of UE and UC were superior to those of conventional US. AUC was the largest (AUC = 0.908) and the diagnostic value was the highest in the conventional US combined with UE and UC. Conventional US combined with elastography and UC can significantly improve the sensitivity, specificity and accuracy of diagnosis of benign and malignant thyroid nodules.

A nationwide survey of deep fungal infections and fungal prophylaxis after hematopoietic stem cell transplantation in Japan.

PubMed

Imataki, O; Kami, M; Kim, S-W; Gotoh, M; Komaba, S; Kasai, M; Hashino, S; Naito, K; Masuda, M; Anan, K; Teshima, H; Togitani, K; Inoue, T; Nishimura, M; Adachi, Y; Fukuhara, T; Yamashita, T; Uike, N; Kobayashi, Y; Hamaguchi, M; Higuchi, M; Kawakami, K; Takaue, Y

2004-06-01

We conducted a nationwide survey to define incidence of deep fungal infections and fungal prophylaxis practices after HSCT. In all, 63 institutions responded. Total number of in-patient transplantations was 935: 367 autologous, 414 allogeneic myeloablative, and 154 allogeneic reduced-intensity (RIST) (n=154). Number of patients who were cared for in a clean room at transplant was 261 (71%) in autologous, 409 (99%) in conventional and 93 (66%) in RIST, respectively. All patients received prophylactic antifungal agents; 89% fluconazole. Number of patients who received the dosage recommended in the CDC guidelines (400 mg/day) was 135 (42%) in conventional transplant and 34 (30%) in RIST (P=0.037). Number of patients who received fluconazole until engraftment and beyond day 75 in conventional transplant vs RIST was, respectively, 324 (100%) vs 109 (97%), and 39 (12%) vs 18 (16%), with no significant difference between the two groups. A total of 37 patients (4.0%) were diagnosed with deep fungal infections; autologous transplantation (0.03%), conventional transplantation (6.0%) and RIST (7.1%). Wide variations in antifungal prophylaxis practice according to the type of transplant and the institutions, and deep fungal infection remain significant problems in RIST.

The effect of a whole-body vibration therapy on the sitting balance of subacute stroke patients: a randomized controlled trial.

PubMed

Lee, Jong Hwa; Kim, Sang Beom; Lee, Kyeong Woo; Lee, Sook Joung; Park, Hyuntae; Kim, Dong Won

2017-09-01

The use of a whole-body vibration (WBV) therapy has recently been applied and investigated as a rehabilitation method for subacute stroke patients. To evaluate the effects of a WBV therapy on recovery of balance in subacute stroke patients who were unable to gain sitting balance. The conventional rehabilitation group (CG) received conventional physical therapy, including sitting balance training by a physical therapist, for 30 min a one session, for twice a day for five days a week for two weeks. The whole-body vibration group (VG) received one session of conventional physical therapy, and received WBV therapy instead of conventional physical therapy for 30 min a day for five days a week for two weeks. There were 15 patients in the CG and 15 patients in the VG who completed the two-week therapy. After the two-week therapy, both groups showed functional improvement. Patients in the VG improved functional ambulation categories, Berg balance scale, trunk impairment scale scores. But, no statistically significant correlations between the therapeutic methods and outcomes were observed in either group. Our results suggest that WBV therapy led to improvement of the recovery in balance recovery for subacute stroke patients. Because the WBV therapy was as effective as conventional physical therapy, we can consider a WBV therapy as a clinical method to improve the sitting balance of subacute stoke patients.

Three-Dimensional Messages for Interstellar Communication

NASA Astrophysics Data System (ADS)

Vakoch, Douglas A.

One of the challenges facing independently evolved civilizations separated by interstellar distances is to communicate information unique to one civilization. One commonly proposed solution is to begin with two-dimensional pictorial representations of mathematical concepts and physical objects, in the hope that this will provide a foundation for overcoming linguistic barriers. However, significant aspects of such representations are highly conventional, and may not be readily intelligible to a civilization with different conventions. The process of teaching conventions of representation may be facilitated by the use of three-dimensional representations redundantly encoded in multiple formats (e.g., as both vectors and as rasters). After having illustrated specific conventions for representing mathematical objects in a three-dimensional space, this method can be used to describe a physical environment shared by transmitter and receiver: a three-dimensional space defined by the transmitter--receiver axis, and containing stars within that space. This method can be extended to show three-dimensional representations varying over time. Having clarified conventions for representing objects potentially familiar to both sender and receiver, novel objects can subsequently be depicted. This is illustrated through sequences showing interactions between human beings, which provide information about human behavior and personality. Extensions of this method may allow the communication of such culture-specific features as aesthetic judgments and religious beliefs. Limitations of this approach will be noted, with specific reference to ETI who are not primarily visual.

Unconventional signal detection techniques with Gaussian probability mixtures adaptation in non-AWGN channels: full resolution receiver

NASA Astrophysics Data System (ADS)

Chabdarov, Shamil M.; Nadeev, Adel F.; Chickrin, Dmitry E.; Faizullin, Rashid R.

2011-04-01

In this paper we discuss unconventional detection technique also known as «full resolution receiver». This receiver uses Gaussian probability mixtures for interference structure adaptation. Full resolution receiver is alternative to conventional matched filter receivers in the case of non-Gaussian interferences. For the DS-CDMA forward channel with presence of complex interferences sufficient performance increasing was shown.

Knowledge Dissemination of Intimate Partner Violence Intervention Studies Measured Using Alternative Metrics: Results From a Scoping Review.

PubMed

Madden, Kim; Evaniew, Nathan; Scott, Taryn; Domazetoska, Elena; Dosanjh, Pritnek; Li, Chuan Silvia; Thabane, Lehana; Bhandari, Mohit; Sprague, Sheila

2016-07-01

Alternative metrics measure the number of online mentions that an academic paper receives, including mentions in social media and online news outlets. It is important to monitor and measure dispersion of intimate partner violence (IPV) victim intervention research so that we can improve our knowledge translation and exchange (KTE) processes improving utilization of study findings. The objective of this study is to describe the dissemination of published IPV victim intervention studies and to explore which study characteristics are associated with a greater number of alternative metric mentions and conventional citations. As part of a larger scoping review, we conducted a literature search to identify IPV intervention studies. Outcomes included znumber of alternative metric mentions and conventional citations. Fifty-nine studies were included in this study. The median number of alternative metric mentions was six, and the median number of conventional citations was two. Forty-one percent of the studies (24/59) had no alternative metric mentions, and 27% (16/59) had no conventional citations. Longer time since publication was significantly associated with a greater number of mentions and citations, as were systematic reviews and randomized controlled trial designs. The majority of IPV studies receive little to no online attention or citations in academic journals, indicating a need for the field to focus on implementing strong knowledge dissemination plans. The papers receiving the most alternative metric mentions and conventional citations were also the more rigorous study designs, indicating a need to focus on study quality. We recommend using alternative metrics in conjunction with conventional metrics to evaluate the full dissemination of IPV research.

Student Learning Strategy and Soft-skill in Clothing Business Management

NASA Astrophysics Data System (ADS)

Ampera, D.

2018-02-01

Clothing Business Management course is a subject delivering knowledge and skills about how to manage clothing business. This course requires students’ ethics, leadership, commitment, toughness, honesty, and the ability to take initiative, argue logically, and work together. However, students are not fully efficient in managing a business during practical task. The purpose of the study is to investigate: (1) the differences of students’ learning achievement between those receiving gradual and conventional learning strategy, (2)the effect of interactions between learning strategy and soft skills toward students learning achievement, (3) the differences of learning achievement of high soft skills students who receive gradual and conventional learning strategy, (4) the differences of learning achievement of low soft skills students who receive gradual and conventional learning strategy. The 2x2 treatment-by-level experimental study was carried out in Dressmaking Study Program. The result proved significantly that, overall, differences of students learning achievement exist, except of low soft skills students.

Effects of Small-Group Tutoring with and without Validated Classroom Instruction on At-Risk Students' Math Problem Solving: Are Two Tiers of Prevention Better Than One?

PubMed

Fuchs, Lynn S; Fuchs, Douglas; Craddock, Caitlin; Hollenbeck, Kurstin N; Hamlett, Carol L; Schatschneider, Christopher

2008-01-01

The purpose of this study was to assess the effects of small-group tutoring with and without validated classroom instruction on at-risk (AR) students' math problem solving. Stratifying within schools, 119 3(rd)-grade classes were randomly assigned to conventional or validated problem-solving instruction (Hot Math [schema-broadening instruction]). Students identified as AR (n = 243) were randomly assigned, within classroom conditions, to receive Hot Math tutoring or not. Students were tested on problem-solving and math applications measures before and after 16 weeks of intervention. Analyses of variance, which accounted for the nested structure of the data, revealed the tutored students who received validated classroom instruction achieved better than tutored students who received conventional classroom instruction (ES = 1.34). However, the advantage for tutoring over no tutoring was similar whether or not students received validated or conventional classroom instruction (ESs = 1.18 and 1.13). Tutoring, not validated classroom instruction reduced the prevalence of math difficulty. Implications for responsiveness-to-intervention prevention models and for enhancing math problem-solving instruction are discussed.

Analysis of switch and examine combining with post-examining selection in cognitive radio

NASA Astrophysics Data System (ADS)

Agarwal, Rupali; Srivastava, Neelam; Katiyar, Himanshu

2018-06-01

To perform spectrum sensing in fading environment is one of the most challenging tasks for a CR system. Diversity combining schemes are used to combat the effect of fading and hence detection probability of CR gets improved. Among many diversity combining techniques, switched diversity offers one of the lowest complexity solutions. The receiver embedded with switched diversity looks for an acceptable diversity path (having signal to noise ratio (SNR) above the required threshold) to receive the data. In conventional switch and examine combining (SEC) scheme, when no acceptable path is found after all the paths are examined, the receiver randomly chooses an unacceptable path. Switch and examine combining with post-examining selection (SECp) is a modified version of conventional SEC. In SECp, the conventional SEC scheme is altered in a way that it selects the best path when no acceptable path is found after all paths have been examined. In this paper, formula for probability of detection ( ?) is derived using SECp and SEC diversity combining technique over Rayleigh fading channel. Also the performance of SECp is compared with SEC and no diversity case. Performance comparison is done with the help of SNR vs. ? and complementary receiver operating characteristic curves.

Effects of Small-Group Tutoring with and without Validated Classroom Instruction on At-Risk Students' Math Problem Solving: Are Two Tiers of Prevention Better Than One?

PubMed Central

Fuchs, Lynn S.; Fuchs, Douglas; Craddock, Caitlin; Hollenbeck, Kurstin N.; Hamlett, Carol L.; Schatschneider, Christopher

2008-01-01

The purpose of this study was to assess the effects of small-group tutoring with and without validated classroom instruction on at-risk (AR) students' math problem solving. Stratifying within schools, 119 3rd-grade classes were randomly assigned to conventional or validated problem-solving instruction (Hot Math [schema-broadening instruction]). Students identified as AR (n = 243) were randomly assigned, within classroom conditions, to receive Hot Math tutoring or not. Students were tested on problem-solving and math applications measures before and after 16 weeks of intervention. Analyses of variance, which accounted for the nested structure of the data, revealed the tutored students who received validated classroom instruction achieved better than tutored students who received conventional classroom instruction (ES = 1.34). However, the advantage for tutoring over no tutoring was similar whether or not students received validated or conventional classroom instruction (ESs = 1.18 and 1.13). Tutoring, not validated classroom instruction reduced the prevalence of math difficulty. Implications for responsiveness-to-intervention prevention models and for enhancing math problem-solving instruction are discussed. PMID:19122881

Comparative Short-Term Clinical Outcomes of Mediastinum Tumor Excision Performed by Conventional VATS and Single-Port VATS: Is It Worthwhile?

PubMed

Wu, Ching-Feng; Gonzalez-Rivas, Diego; Wen, Chih-Tsung; Liu, Yun-Hen; Wu, Yi-Cheng; Chao, Yin-Kai; Hsieh, Ming-Ju; Wu, Ching-Yang; Chen, Wei-Hsun

2015-11-01

Single-port video-assisted thoracoscopic surgery (VATS) has been widely applied recently. However, there are still only few reports describing its use in mediastinum tumor resection. We present the technique of single-port video-assisted thoracoscopic mediastinum tumor resection and compare it with conventional VATS with regard to short-term outcome.We retrospectively enrolled 105 patients who received mediastinum surgery in Chang Gung Memorial Hospital. Sixteen patients received sternotomy or thoracotomy, 29 patients received single-port VATS, and 60 patients received conventional VATS (3 ports). The operative time, blood loss, postoperation day 1 pain score, discharge day pain score, and postoperative hospital stay were compared. In order to establish a well balanced cohort study, we also use propensity scores match (1:1) to compare the short-term clinical outcome in 2 groups.No operative deaths occurred in this study. Single-port VATS was associated with shorter operative time, lower postoperation day 1 pain score, and shorter postoperation hospital stay in our cohort study (P = 0.001, <0.001, and 0.039), and propensity scores matched cohort study (P = 0.003, <0.001, and <0.001).Single-port VATS for mediastinum tumor appears to be a safe and promising technique with short-term outcome not inferior to conventional VATS in our cohort study. The long-term oncology outcome may require time and more enrolled patients to be further evaluated.

Multi-Institutional Evaluation of Digital Tomosynthesis, Dual-Energy Radiography, and Conventional Chest Radiography for the Detection and Management of Pulmonary Nodules.

PubMed

Dobbins, James T; McAdams, H Page; Sabol, John M; Chakraborty, Dev P; Kazerooni, Ella A; Reddy, Gautham P; Vikgren, Jenny; Båth, Magnus

2017-01-01

Purpose To conduct a multi-institutional, multireader study to compare the performance of digital tomosynthesis, dual-energy (DE) imaging, and conventional chest radiography for pulmonary nodule detection and management. Materials and Methods In this binational, institutional review board-approved, HIPAA-compliant prospective study, 158 subjects (43 subjects with normal findings) were enrolled at four institutions. Informed consent was obtained prior to enrollment. Subjects underwent chest computed tomography (CT) and imaging with conventional chest radiography (posteroanterior and lateral), DE imaging, and tomosynthesis with a flat-panel imaging device. Three experienced thoracic radiologists identified true locations of nodules (n = 516, 3-20-mm diameters) with CT and recommended case management by using Fleischner Society guidelines. Five other radiologists marked nodules and indicated case management by using images from conventional chest radiography, conventional chest radiography plus DE imaging, tomosynthesis, and tomosynthesis plus DE imaging. Sensitivity, specificity, and overall accuracy were measured by using the free-response receiver operating characteristic method and the receiver operating characteristic method for nodule detection and case management, respectively. Results were further analyzed according to nodule diameter categories (3-4 mm, >4 mm to 6 mm, >6 mm to 8 mm, and >8 mm to 20 mm). Results Maximum lesion localization fraction was higher for tomosynthesis than for conventional chest radiography in all nodule size categories (3.55-fold for all nodules, P < .001; 95% confidence interval [CI]: 2.96, 4.15). Case-level sensitivity was higher with tomosynthesis than with conventional chest radiography for all nodules (1.49-fold, P < .001; 95% CI: 1.25, 1.73). Case management decisions showed better overall accuracy with tomosynthesis than with conventional chest radiography, as given by the area under the receiver operating characteristic curve (1.23-fold, P < .001; 95% CI: 1.15, 1.32). There were no differences in any specificity measures. DE imaging did not significantly affect nodule detection when paired with either conventional chest radiography or tomosynthesis. Conclusion Tomosynthesis outperformed conventional chest radiography for lung nodule detection and determination of case management; DE imaging did not show significant differences over conventional chest radiography or tomosynthesis alone. These findings indicate performance likely achievable with a range of reader expertise. © RSNA, 2016 Online supplemental material is available for this article.

Multi-Institutional Evaluation of Digital Tomosynthesis, Dual-Energy Radiography, and Conventional Chest Radiography for the Detection and Management of Pulmonary Nodules

PubMed Central

McAdams, H. Page; Sabol, John M.; Chakraborty, Dev P.; Kazerooni, Ella A.; Reddy, Gautham P.; Vikgren, Jenny; Båth, Magnus

2017-01-01

Purpose To conduct a multi-institutional, multireader study to compare the performance of digital tomosynthesis, dual-energy (DE) imaging, and conventional chest radiography for pulmonary nodule detection and management. Materials and Methods In this binational, institutional review board–approved, HIPAA-compliant prospective study, 158 subjects (43 subjects with normal findings) were enrolled at four institutions. Informed consent was obtained prior to enrollment. Subjects underwent chest computed tomography (CT) and imaging with conventional chest radiography (posteroanterior and lateral), DE imaging, and tomosynthesis with a flat-panel imaging device. Three experienced thoracic radiologists identified true locations of nodules (n = 516, 3–20-mm diameters) with CT and recommended case management by using Fleischner Society guidelines. Five other radiologists marked nodules and indicated case management by using images from conventional chest radiography, conventional chest radiography plus DE imaging, tomosynthesis, and tomosynthesis plus DE imaging. Sensitivity, specificity, and overall accuracy were measured by using the free-response receiver operating characteristic method and the receiver operating characteristic method for nodule detection and case management, respectively. Results were further analyzed according to nodule diameter categories (3–4 mm, >4 mm to 6 mm, >6 mm to 8 mm, and >8 mm to 20 mm). Results Maximum lesion localization fraction was higher for tomosynthesis than for conventional chest radiography in all nodule size categories (3.55-fold for all nodules, P < .001; 95% confidence interval [CI]: 2.96, 4.15). Case-level sensitivity was higher with tomosynthesis than with conventional chest radiography for all nodules (1.49-fold, P < .001; 95% CI: 1.25, 1.73). Case management decisions showed better overall accuracy with tomosynthesis than with conventional chest radiography, as given by the area under the receiver operating characteristic curve (1.23-fold, P < .001; 95% CI: 1.15, 1.32). There were no differences in any specificity measures. DE imaging did not significantly affect nodule detection when paired with either conventional chest radiography or tomosynthesis. Conclusion Tomosynthesis outperformed conventional chest radiography for lung nodule detection and determination of case management; DE imaging did not show significant differences over conventional chest radiography or tomosynthesis alone. These findings indicate performance likely achievable with a range of reader expertise. © RSNA, 2016 Online supplemental material is available for this article. PMID:27439324

Off-label use of rituximab for systemic lupus erythematosus in Europe.

PubMed

Rydén-Aulin, Monica; Boumpas, Dimitrios; Bultink, Irene; Callejas Rubio, Jose Luis; Caminal-Montero, Luis; Castro, Antoni; Colodro Ruiz, Agustín; Doria, Andrea; Dörner, Thomas; Gonzalez-Echavarri, Cristina; Gremese, Elisa; Houssiau, Frederic A; Huizinga, Tom; Inanç, Murat; Isenberg, David; Iuliano, Annamaria; Jacobsen, Søren; Jimenéz-Alonso, Juan; Kovács, Lászlo; Mariette, Xavier; Mosca, Marta; Nived, Ola; Oristrell, Joaquim; Ramos-Casals, Manuel; Rascón, Javier; Ruiz-Irastorza, Guillermo; Sáez-Comet, Luis; Salvador Cervelló, Gonzalo; Sebastiani, Gian Domenico; Squatrito, Danilo; Szücs, Gabriella; Voskuyl, Alexandre; van Vollenhoven, Ronald

2016-01-01

Rituximab (RTX) is a biological treatment used off-label in patients with systemic lupus erythematosus (SLE). This survey aimed to investigate the off-label use of RTX in Europe and compare the characteristics of patients receiving RTX with those receiving conventional therapy. Data on patients with SLE receiving RTX were taken from the International Registry for Biologics in SLE retrospective registry and complemented with data on patients with SLE treated with conventional therapy. For nationwide estimates of RTX use in patients with SLE, investigators were asked to provide data through case report forms (CRFs). Countries for which no data were submitted through CRFs, published literature and/or personal communication were used, and for European countries where no data were available, estimates were made on the assumption of similarities with neighbouring countries. The estimated off-label use of RTX in Europe was 0.5%-1.5% of all patients with SLE. In comparison with patients with SLE on conventional therapy, patients treated with RTX had longer disease duration, higher disease activity and were more often treated with immunosuppressives. The most frequent organ manifestations for which either RTX or conventional therapy was initiated were lupus nephritis followed by musculoskeletal and haematological. The reason for treatment was, besides disease control, corticosteroid-sparing for patients treated with conventional therapy. RTX use for SLE in Europe is restrictive and appears to be used as a last resort in patients for whom other reasonable options have been exhausted.

Off-label use of rituximab for systemic lupus erythematosus in Europe

PubMed Central

Rydén-Aulin, Monica; Boumpas, Dimitrios; Bultink, Irene; Callejas Rubio, Jose Luis; Caminal-Montero, Luis; Castro, Antoni; Colodro Ruiz, Agustín; Doria, Andrea; Dörner, Thomas; Gonzalez-Echavarri, Cristina; Gremese, Elisa; Houssiau, Frederic A; Huizinga, Tom; Inanç, Murat; Isenberg, David; Iuliano, Annamaria; Jacobsen, Søren; Jimenéz-Alonso, Juan; Kovács, Lászlo; Mariette, Xavier; Mosca, Marta; Nived, Ola; Oristrell, Joaquim; Ramos-Casals, Manuel; Rascón, Javier; Sáez-Comet, Luis; Salvador Cervelló, Gonzalo; Sebastiani, Gian Domenico; Squatrito, Danilo; Szücs, Gabriella; Voskuyl, Alexandre; van Vollenhoven, Ronald

2016-01-01

Objectives Rituximab (RTX) is a biological treatment used off-label in patients with systemic lupus erythematosus (SLE). This survey aimed to investigate the off-label use of RTX in Europe and compare the characteristics of patients receiving RTX with those receiving conventional therapy. Methods Data on patients with SLE receiving RTX were taken from the International Registry for Biologics in SLE retrospective registry and complemented with data on patients with SLE treated with conventional therapy. For nationwide estimates of RTX use in patients with SLE, investigators were asked to provide data through case report forms (CRFs). Countries for which no data were submitted through CRFs, published literature and/or personal communication were used, and for European countries where no data were available, estimates were made on the assumption of similarities with neighbouring countries. Results The estimated off-label use of RTX in Europe was 0.5%–1.5% of all patients with SLE. In comparison with patients with SLE on conventional therapy, patients treated with RTX had longer disease duration, higher disease activity and were more often treated with immunosuppressives. The most frequent organ manifestations for which either RTX or conventional therapy was initiated were lupus nephritis followed by musculoskeletal and haematological. The reason for treatment was, besides disease control, corticosteroid-sparing for patients treated with conventional therapy. Conclusions RTX use for SLE in Europe is restrictive and appears to be used as a last resort in patients for whom other reasonable options have been exhausted. PMID:27651920

The First Page of the Official Journal of the Constitutional Convention--Just the Tip of a Records Iceberg!

ERIC Educational Resources Information Center

Potter, Lee Ann

2012-01-01

On Monday, September 17, 1787, 39 delegates to the Federal Convention in Philadelphia signed the Constitution of the United States, along with Major William Jackson, who had served as the secretary of the Convention. That same day, Jackson received instructions to leave for New York City on Tuesday and carry the document to Congress. All of these…

Multi-Band Received Signal Strength Fingerprinting Based Indoor Location System

NASA Astrophysics Data System (ADS)

Sertthin, Chinnapat; Fujii, Takeo; Ohtsuki, Tomoaki; Nakagawa, Masao

This paper proposes a new multi-band received signal strength (MRSS) fingerprinting based indoor location system, which employs the frequency diversity on the conventional single-band received signal strength (RSS) fingerprinting based indoor location system. In the proposed system, the impacts of frequency diversity on the enhancements of positioning accuracy are analyzed. Effectiveness of the proposed system is proved by experimental approach, which was conducted in non line-of-sight (NLOS) environment under the area of 103m2 at Yagami Campus, Keio University. WLAN access points, which simultaneously transmit dual-band signal of 2.4 and 5.2GHz, are utilized as transmitters. Likewise, a dual-band WLAN receiver is utilized as a receiver. Signal distances calculated by both Manhattan and Euclidean were classified by K-Nearest Neighbor (KNN) classifier to illustrate the performance of the proposed system. The results confirmed that Frequency diversity attributions of multi-band signal provide accuracy improvement over 50% of the conventional single-band.

Effects of frequent hemodialysis on perceived caregiver burden in the Frequent Hemodialysis Network trials.

PubMed

Suri, Rita S; Larive, Brett; Hall, Yoshio; Kimmel, Paul L; Kliger, Alan S; Levin, Nathan; Tamura, Manjula Kurella; Chertow, Glenn M

2014-05-01

Patients receiving hemodialysis often perceive their caregivers are overburdened. We hypothesize that increasing hemodialysis frequency would result in higher patient perceptions of burden on their unpaid caregivers. In two separate trials, 245 patients were randomized to receive in-center daily hemodialysis (6 days/week) or conventional hemodialysis (3 days/week) while 87 patients were randomized to receive home nocturnal hemodialysis (6 nights/week) or home conventional hemodialysis for 12 months. Changes in overall mean scores over time in the 10-question Cousineau perceived burden scale were compared. In total, 173 of 245 (70%) and 80 of 87 (92%) randomized patients in the Daily and Nocturnal Trials, respectively, reported having an unpaid caregiver at baseline or during follow-up. Relative to in-center conventional dialysis, the 12-month change in mean perceived burden score with in-center daily hemodialysis was -2.1 (95% confidence interval, -9.4 to +5.3; P=0.58). Relative to home conventional dialysis, the 12-month change in mean perceived burden score with home nocturnal dialysis was +6.1 (95% confidence interval, -0.8 to +13.1; P=0.08). After multiple imputation for missing data in the Nocturnal Trial, the relative difference between home nocturnal and home conventional hemodialysis was +9.4 (95% confidence interval, +0.55 to +18.3; P=0.04). In the Nocturnal Trial, changes in perceived burden were inversely correlated with adherence to dialysis treatments (Pearson r=-0.35; P=0.02). Relative to conventional hemodialysis, in-center daily hemodialysis did not result in higher perceptions of caregiver burden. There was a trend to higher perceived caregiver burden among patients randomized to home nocturnal hemodialysis. These findings may have implications for the adoption of and adherence to frequent nocturnal hemodialysis.

Advanced solar receiver conceptual design study

NASA Technical Reports Server (NTRS)

Kesseli, J. B.; Lacy, D. E.

1987-01-01

High temperature solar dynamic Brayton and Stirling receivers are investigated as candidate electrical power generating systems for future LEO missions. These receivers are smaller and more efficient than conventional receivers, and they offer less structural complexity and fewer thermal stress problems. Use of the advanced Direct Absorption Storage Receiver allows many of the problems associated with working with high-volumetric-change phase-change materials to be avoided. A specific mass reduction of about 1/3 with respect to the baseline receiver has been realized.

Novel Control Effectors for Truss Braced Wing

NASA Technical Reports Server (NTRS)

White, Edward V.; Kapania, Rakesh K.; Joshi, Shiv

2015-01-01

At cruise flight conditions very high aspect ratio/low sweep truss braced wings (TBW) may be subject to design requirements that distinguish them from more highly swept cantilevered wings. High aspect ratio, short chord length and relative thinness of the airfoil sections all contribute to relatively low wing torsional stiffness. This may lead to aeroelastic issues such as aileron reversal and low flutter margins. In order to counteract these issues, high aspect ratio/low sweep wings may need to carry additional high speed control effectors to operate when outboard ailerons are in reversal and/or must carry additional structural weight to enhance torsional stiffness. The novel control effector evaluated in this study is a variable sweep raked wing tip with an aileron control surface. Forward sweep of the tip allows the aileron to align closely with the torsional axis of the wing and operate in a conventional fashion. Aft sweep of the tip creates a large moment arm from the aileron to the wing torsional axis greatly enhancing aileron reversal. The novelty comes from using this enhanced and controllable aileron reversal effect to provide roll control authority by acting as a servo tab and providing roll control through intentional twist of the wing. In this case the reduced torsional stiffness of the wing becomes an advantage to be exploited. The study results show that the novel control effector concept does provide roll control as described, but only for a restricted class of TBW aircraft configurations. For the configuration studied (long range, dual aisle, Mach 0.85 cruise) the novel control effector provides significant benefits including up to 12% reduction in fuel burn.

Wind Tunnel Results from a Nozzle Afterbody Test of a 0.2-Scale Fighter Aircraft in the Mach Number Regime of 0.6 to 1.5. Volume 1. Test Technique Evaluation

DTIC Science & Technology

1979-04-01

edge up. The influence of the aircraft on the static pressure reading from the pitot boom was determined with a scaled version of the pltot probe...stabilization before advancing to the next port. Jet exhaust simulation flow was monitored by internal duct pressure and temperature rakes . Standard...Mach numbers 0.6 and 1.2, Figs. 24 and 25. 13 AE DC-TR-79-10 At supersonic speeds, changes in the afterbody and nozzle axial loads (Fig. 22b) are

Tools being considered for use in freeing solar array wing of Skylab

NASA Technical Reports Server (NTRS)

1973-01-01

Engineers at the Marshall Space Flight Center examine tools that are being considered for use in freeing the solar array wing of Skylab. The device at center is a cable cutter which is operated by cable. At right is the handle end of a rod. White material taped just below the handle is buoyancy packing to make the oject weightless when submerged in water. Small object at left is the attachment head for a two-prong 'rake' device for use on the end of a pole made up of one, two or more five-foot secitons of extension rods.

Connections between survey calibration estimators and semiparametric models for incomplete data

PubMed Central

Lumley, Thomas; Shaw, Pamela A.; Dai, James Y.

2012-01-01

Survey calibration (or generalized raking) estimators are a standard approach to the use of auxiliary information in survey sampling, improving on the simple Horvitz–Thompson estimator. In this paper we relate the survey calibration estimators to the semiparametric incomplete-data estimators of Robins and coworkers, and to adjustment for baseline variables in a randomized trial. The development based on calibration estimators explains the ‘estimated weights’ paradox and provides useful heuristics for constructing practical estimators. We present some examples of using calibration to gain precision without making additional modelling assumptions in a variety of regression models. PMID:23833390

Measurement of beam divergence of 30-centimeter dished grids

NASA Technical Reports Server (NTRS)

Danilowicz, R. L.; Rawlin, V. K.; Banks, B. A.; Wintucky, E. G.

1973-01-01

The beam divergence of a 30-centimeter diameter thruster with dished grids was calculated from current densities measured with a probe rake containing seventeen planar molybdenum probes. The measured data were analyzed as a function of a number of parameters. The most sensitive parameters were the amount of compensation of the accelerator grid and the ratio of net to total accelerating voltage. The thrust losses were reduced by over 5 percent with the use of compensated grids alone, and by variation of other parameters the overall thrust losses due to beam divergence were reduced to less than 2 percent.

Ship To Ship Pulse Recognition System

DTIC Science & Technology

1941-10-24

rflr" scrcwtirivar. At the tW;, a: tte cAbinet are a pli,; connectio f~Lrom, tae .uplexer to the antenn -a switci., t:.e control oea n to the antenna...The blinker li.)it uwncs L~.. sec 15 wrntto U1S Volt ia.;isa in ’WijarajL J1i. ’fli* p~rcp&a~aioY1 syv~o- (antmnnimi Antenne switch aind fIlipiexer...Iinput to thePrWsel•etr Is a 31/Sm coOentric line whose center conductor rakes a eml loop to pound which servos to inductively couple the antma system

Measurement of beam divergence of 30-centimeter dished grids

NASA Technical Reports Server (NTRS)

Danilowicz, R. L.; Rawlin, V. K.; Banks, B. A.; Wintucky, E. G.

1973-01-01

The beam divergence of a 30-centimeter diameter thrustor with dished grids was calculated from current densities measured with a probe rake containing seventeen planar molybdenum probes. The measured data were analyzed as a function of a number of parameters. The most sensitive parameters were the amount of compensation of the accelerator grid and the ratio of net to total accelerating voltage. The thrust losses were reduced by over 5 percent with the use of compensated grids alone, and by variation of other parameters the overall thrust losses due to beam divergence were reduced to less than 2 percent.

Influence of technical parameters of disk-shaped reactor on productivity of heat treatment of crushed wood

NASA Astrophysics Data System (ADS)

Safin, R. R.; Khasanshin, R. R.; Mukhametzyanov, S. R.

2018-03-01

The existing installations for heat treatment of the crushed wood are analyzed. The technology of heat treatment of the crushed wood in the devices of disk-shaped type is offered. The results of modeling for the purpose of determination of interrelation of the key design and technological parameters of the disk-shaped device are presented. It is established that the major factors, affecting duration of stay of the material in a device, are the speed of rotation of the mixer, the number of mixers and the number of rakes on the mixer.

Experimental Study of the Influence of Speed and Load on Thermal Behavior of High-Speed Helical Gear Trains

NASA Technical Reports Server (NTRS)

Handschuh, R.; Kilmain, C.

2005-01-01

An experimental effort has been conducted on an aerospace-quality helical gear train to investigate the thermal behavior of the gear system as speed, load, and lubricant flow rate were varied. Temperature test data from a helical gear train at varying speeds and loads (to 5000 hp and 15000 rpm) was collected using thermocouple rakes and axial arrays. The instrumentation was able to capture the radial and axial expelled lubricant-air environment (fling-off lubricant) that is expelled during the gear meshing process. Effects of operational characteristics are presented.

77 FR 12371 - Proposed Collection; Comment Request for Regulation Project

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

... applicable conventions under the accelerated cost recovery system. DATES: Written comments should be received... INFORMATION: Title: Applicable Conventions Under the Accelerated Cost Recovery System. OMB Number: 1545-1146...-profit organizations, and farms. Estimated Number of Respondents: 700. Estimated Time per Respondent: 6...

Intensive diabetes therapy and ocular surgery in type 1 diabetes.

PubMed

Aiello, Lloyd Paul; Sun, Wanjie; Das, Arup; Gangaputra, Sapna; Kiss, Szilard; Klein, Ronald; Cleary, Patricia A; Lachin, John M; Nathan, David M

2015-04-30

The Diabetes Control and Complications Trial (DCCT) showed a beneficial effect of 6.5 years of intensive glycemic control on retinopathy in patients with type 1 diabetes. Between 1983 and 1989, a total of 1441 patients with type 1 diabetes in the DCCT were randomly assigned to receive either intensive diabetes therapy or conventional therapy aimed at preventing hyperglycemic symptoms. They were treated and followed until 1993. Subsequently, 1375 of these patients were followed in the observational Epidemiology of Diabetes Interventions and Complications (EDIC) study. The self-reported history of ocular surgical procedures was obtained annually. We evaluated the effect of intensive therapy as compared with conventional therapy on the incidence and cost of ocular surgery during these two studies. Over a median follow-up of 23 years, 130 ocular operations were performed in 63 of 711 patients assigned to intensive therapy (8.9%) and 189 ocular operations in 98 of 730 patients assigned to conventional therapy (13.4%) (P<0.001). After adjustment for DCCT baseline factors, intensive therapy was associated with a reduction in the risk of any diabetes-related ocular surgery by 48% (95% confidence interval [CI], 29 to 63; P<0.001) and a reduction in the risk of all such ocular procedures by 37% (95% CI, 12 to 55; P=0.01). Forty-two patients who received intensive therapy and 61 who received conventional therapy underwent cataract extraction (adjusted risk reduction with intensive therapy, 48%; 95% CI, 23 to 65; P=0.002); 29 patients who received intensive therapy and 50 who received conventional therapy underwent vitrectomy, retinal-detachment surgery, or both (adjusted risk reduction, 45%; 95% CI, 12 to 66; P=0.01). The costs of surgery were 32% lower in the intensive-therapy group. The beneficial effects of intensive therapy were fully attenuated after adjustment for mean glycated hemoglobin levels over the entire follow-up. Intensive therapy in patients with type 1 diabetes was associated with a substantial reduction in the long-term risk of ocular surgery. (Funded by the National Institute of Diabetes and Digestive and Kidney Diseases and others; DCCT/EDIC ClinicalTrials.gov numbers, NCT00360893 and NCT00360815.).

A comparative evaluation of pain and anxiety levels in 2 different anesthesia techniques: locoregional anesthesia using conventional syringe versus intraosseous anesthesia using a computer-controlled system (Quicksleeper).

PubMed

Özer, Senem; Yaltirik, Mehmet; Kirli, Irem; Yargic, Ilhan

2012-11-01

The aim of this study was to compare anxiety and pain levels during anesthesia and efficacy of Quicksleeper intraosseous (IO) injection system, which delivers computer-controlled IO anesthesia and conventional inferior alveolar nerve block (IANB) in impacted mandibular third molars. Forty subjects with bilateral impacted mandibular third molars randomly received IO injection or conventional IANB at 2 successive appointments. The subjects received 1.8 mL 2% articaine. IO injection has many advantages, such as enabling painless anesthesia with less soft tissue numbness and quick onset of anesthesia as well as lingual and palatal anesthesia with single needle penetration. Although IO injection is a useful technique commonly used during various treatments in dentistry, the duration of injection takes longer than conventional techniques, there is a possibility of obstruction at the needle tip, and, the duration of the anesthetic effect is inadequate for prolonged surgical procedures. Copyright © 2012 Elsevier Inc. All rights reserved.

Impairments in prehension produced by early postnatal sensory motor cortex activity blockade.

PubMed

Martin, J H; Donarummo, L; Hacking, A

2000-02-01

This study examined the effects of blocking neural activity in sensory motor cortex during early postnatal development on prehension. We infused muscimol, either unilaterally or bilaterally, into the sensory motor cortex of cats to block activity continuously between postnatal weeks 3-7. After stopping infusion, we trained animals to reach and grasp a cube of meat and tested behavior thereafter. Animals that had not received muscimol infusion (unilateral saline infusion; age-matched) reached for the meat accurately with small end-point errors. They grasped the meat using coordinated digit flexion followed by forearm supination on 82.7% of trials. Performance using either limb did not differ significantly. In animals receiving unilateral muscimol infusion, reaching and grasping using the limb ipsilateral to the infusion were similar to controls. The limb contralateral to infusion showed significant increases in systematic and variable reaching end-point errors, often requiring subsequent corrective movements to contact the meat. Grasping occurred on only 14.8% of trials, replaced on most trials by raking without distal movements. Compensatory adjustments in reach length and angle, to maintain end-point accuracy as movements were started from a more lateral position, were less effective using the contralateral limb than ipsilateral limb. With bilateral inactivations, the form of reaching and grasping impairments was identical to that produced by unilateral inactivation, but the magnitude of the reaching impairments was less. We discuss these results in terms of the differential effects of unilateral and bilateral inactivation on corticospinal tract development. We also investigated the degree to which these prehension impairments after unilateral blockade reflect control by each hemisphere. In animals that had received unilateral blockade between postnatal weeks (PWs) 3 and 7, we silenced on-going activity (after PW 11) during task performance using continuous muscimol infusion. We inactivated the right (previously active) and then the left (previously silenced) sensory motor cortex. Inactivation of the ipsilateral (right) sensory motor cortex produced a further increase in systematic error and less frequent normal grasping. Reinactivation of the contralateral (left) cortex produced larger increases in reaching and grasping impairments than those produced by ipsilateral inactivation. This suggests that the impaired limb receives bilateral sensory motor cortex control but that control by the contralateral (initially silenced) cortex predominates. Our data are consistent with the hypothesis that the normal development of skilled motor behavior requires activity in sensory motor cortex during early postnatal life.

77 FR 71501 - International Fisheries; Western and Central Pacific Fisheries for Highly Migratory Species...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-03

...NMFS issues regulations under the authority of the Western and Central Pacific Fisheries Convention Implementation Act (WCPFC Implementation Act) to implement requirements for U.S. fishing vessels used for commercial fishing that offload or receive transshipments of highly migratory species (HMS), U.S. fishing vessels used for commercial fishing that provide bunkering or other support services to fishing vessels, and U.S. fishing vessels used for commercial fishing that receive bunkering or engage in other support services, in the area of application of the Convention on the Conservation and Management of Highly Migratory Fish Stocks in the Western and Central Pacific Ocean (Convention). Some of the requirements also apply to transshipments of fish caught in the area of application of the Convention (Convention Area) and transshipped elsewhere. NMFS also issues requirements regarding notification of entry into and exit from the ``Eastern High Seas Special Management Area'' (Eastern SMA) and requirements relating to discards from purse seine fishing vessels. This action is necessary for the United States to implement decisions of the Commission for the Conservation and Management of Highly Migratory Fish Stocks in the Western and Central Pacific Ocean (Commission or WCPFC) and to satisfy its obligations under the Convention, to which it is a Contracting Party.

Research on the output bit error rate of 2DPSK signal based on stochastic resonance theory

NASA Astrophysics Data System (ADS)

Yan, Daqin; Wang, Fuzhong; Wang, Shuo

2017-12-01

Binary differential phase-shift keying (2DPSK) signal is mainly used for high speed data transmission. However, the bit error rate of digital signal receiver is high in the case of wicked channel environment. In view of this situation, a novel method based on stochastic resonance (SR) is proposed, which is aimed to reduce the bit error rate of 2DPSK signal by coherent demodulation receiving. According to the theory of SR, a nonlinear receiver model is established, which is used to receive 2DPSK signal under small signal-to-noise ratio (SNR) circumstances (between -15 dB and 5 dB), and compared with the conventional demodulation method. The experimental results demonstrate that when the input SNR is in the range of -15 dB to 5 dB, the output bit error rate of nonlinear system model based on SR has a significant decline compared to the conventional model. It could reduce 86.15% when the input SNR equals -7 dB. Meanwhile, the peak value of the output signal spectrum is 4.25 times as that of the conventional model. Consequently, the output signal of the system is more likely to be detected and the accuracy can be greatly improved.

Techno-economic sensitivity study of heliostat field parameters for micro-gas turbine CSP

NASA Astrophysics Data System (ADS)

Landman, Willem A.; Gauché, Paul; Dinter, Frank; Myburgh, J. T.

2017-06-01

Concentrating solar power systems based on micro-gas turbines potentially offer numerous benefits should they become commercially viable. Heliostat fields for such systems have unique requirements in that the number of heliostats and the focal ratios are typically much lower than conventional central receiver systems. This paper presents a techno-economic sensitivity study of heliostat field parameters for a micro-gas turbine central receiver system. A 100 kWe minitower system is considered for the base case and a one-at-a-time strategy is used to investigate parameter sensitivities. Increasing heliostat focal ratios are found to have significant optical performance benefits due to both a reduction in astigmatic aberrations and a reduction in the number of facet focal lengths required; confirming the hypothesis that smaller heliostats offer a techno-economic advantage. Fixed Horizontal Axis tracking mechanism is shown to outperform the conventional Azimuth Zenith tracking mechanism in high density heliostat fields. Although several improvements to heliostat field performance are discussed, the capex fraction of the heliostat field for such system is shown to be almost half that of a conventional central receiver system and optimum utilization of the higher capex components, namely; the receiver and turbine subsystems, are more rewarding than that of the heliostat field.

Influence of etanercept on leptin and ghrelin secretion in children with juvenile idiopathic arthritis.

PubMed

Maciejewska-Paszek, Izabela; Grochowska-Niedworok, Elżbieta; Siwiec, Andrzej; Gruenpeter, Anna; Dul, Lechosław; Irzyniec, Tomasz

2017-04-01

Objective To assess possible changes in leptin and ghrelin secretion due to etanercept in juvenile idiopathic arthritis (JIA). Methods 50 patients with JIA and 16 age-matched controls were enrolled into this prospective, cross-sectional study. Serum leptin, total and acyl ghrelin were measured in addition to white blood cell (WBC) and lymphocyte counts. Results 25 patients received etanercept and 25 conventional therapies (including methotrexate) for JIA. There was no difference between treatment and control groups in leptin or ghrelin levels and no evidence of a relationship between leptin and ghrelin in patients with JIA. In all children with JIA there was a correlation between leptin and body mass index (BMI). However, compared with children in the conventional treatment group, children in the etanercept group showed a positive correlation between total ghrelin and BMI and those with a low BMI showed a negative correlation between acyl ghrelin and BMI. Conclusion No differences in leptin and ghrelin concentrations were found when patients with JIA and controls were compared or when patients who received etanercept were compared with those who received conventional treatment for JIA.

Influence of etanercept on leptin and ghrelin secretion in children with juvenile idiopathic arthritis

PubMed Central

Maciejewska-Paszek, Izabela; Grochowska-Niedworok, Elżbieta; Siwiec, Andrzej; Gruenpeter, Anna; Dul, Lechosław

2017-01-01

Objective To assess possible changes in leptin and ghrelin secretion due to etanercept in juvenile idiopathic arthritis (JIA). Methods 50 patients with JIA and 16 age-matched controls were enrolled into this prospective, cross-sectional study. Serum leptin, total and acyl ghrelin were measured in addition to white blood cell (WBC) and lymphocyte counts. Results 25 patients received etanercept and 25 conventional therapies (including methotrexate) for JIA. There was no difference between treatment and control groups in leptin or ghrelin levels and no evidence of a relationship between leptin and ghrelin in patients with JIA. In all children with JIA there was a correlation between leptin and body mass index (BMI). However, compared with children in the conventional treatment group, children in the etanercept group showed a positive correlation between total ghrelin and BMI and those with a low BMI showed a negative correlation between acyl ghrelin and BMI. Conclusion No differences in leptin and ghrelin concentrations were found when patients with JIA and controls were compared or when patients who received etanercept were compared with those who received conventional treatment for JIA. PMID:28415953

Investigation of coherent receiver designs in high-speed optical inter-satellite links using digital signal processing

NASA Astrophysics Data System (ADS)

Schaefer, S.; Gregory, M.; Rosenkranz, W.

2017-09-01

Due to higher data rates, better data security and unlicensed spectral usage optical inter-satellite links (OISL) offer an attractive alternative to conventional RF-communication. However, the very high transmission distances necessitate an optical receiver design enabling high receiver sensitivity which requires careful carrier synchronization and a quasi-coherent detection scheme.

Simvastatin as an Adjunct to Conventional Therapy of Non-infectious Uveitis: A Randomized, Open-Label Pilot Study.

PubMed

Shirinsky, Ivan V; Biryukova, Anastasia A; Shirinsky, Valery S

2017-12-01

Statins have been shown to reduce ocular inflammation in animal models of uveitis and to prevent development of uveitis in observational studies. There have been no experimental human studies evaluating statins' efficacy and safety in uveitis. In this study, we aimed to investigate efficacy and safety of simvastatin in patients with uveitis. For this single-center, open-label, randomized study, we enrolled patients with acute non-infectious uveitis. The patients were randomized to receive 40 mg simvastatin per day for 2 months in addition to conventional treatment or conventional treatment alone. The studied outcomes were the rate of steroid-sparing control of ocular inflammation, measures of ocular inflammation, intraocular pressure, and visual acuity. Fifty patients were enrolled in the study. Twenty-five patients were randomly assigned to receive simvastatin with conventional treatment and 25 to conventional treatment alone. Simvastatin was associated with significantly higher rates of steroid-sparing ocular inflammation control, decrease in anterior chamber inflammation, and improvement in visual acuity. The treatment was well tolerated, no serious adverse effects were observed. Our findings suggest that statins may have therapeutic potential in uveitis. These results need to be confirmed in double-blind, randomized, controlled studies.

Novel Neuromuscular Electrical Stimulation System for Treatment of Dysphagia after Brain Injury

PubMed Central

TOYAMA, Keiichi; MATSUMOTO, Shuji; KURASAWA, Miho; SETOGUCHI, Haruka; NOMA, Tomokazu; TAKENAKA, Keita; SOEDA, Akina; SHIMODOZONO, Megumi; KAWAHIRA, Kazumi

2014-01-01

The purpose of this study was to compare the effects of a novel neuromuscular electrical stimulation (NMES) to the effects of conventional treatment in patients with dysphagia after brain injury. In total, 26 patients were non-randomly divided into an experimental group (n = 12) and a control group (n = 14). The experimental group received NMES intervention followed by conventional treatment, including thermal-tactile stimulation with intensive repetition of a dry-swallow task. The control group received conventional treatment without NMES. NMES at a fixed pulse duration of 50 μs and a frequency of 50 Hz was delivered over the skin areas above the motor point of the target muscles, i.e., the bilateral geniohyoid, mylohyoid/anterior belly of the digastric, and thyrohyoid muscles, using a high-voltage pulsed-current device. The two groups received 40-min treatments once a day, 5 days per week, for 8 weeks. Outcome, assessed before and 8 weeks after treatment, was evaluated with regard to the videofluoroscopic dysphagia scale (VDS), the anterior and superior displacement of the hyoid bone and larynx, and the functional oral intake scale. Both groups exhibited improvement, but the experimental group exhibited more significant improvement in the displacement of the hyoid bone and larynx, VDS-total score, and VDS-pharyngeal score than the control group did. The results suggest that NMES combined with conventional treatment is superior to conventional treatment alone in patients with dysphagia following treatment for brain injury. Further investigations are necessary to examine the effects of NMES in patients with more varied types of diseases. PMID:24670314

Improving Diagrammatic Reasoning in Middle School Science Using Conventions of Diagrams Instruction

ERIC Educational Resources Information Center

Miller, B. W.; Cromley, J. G.; Newcombe, N. S.

2016-01-01

Visual representations are essential for science understanding, but many students have poor diagrammatic reasoning skills. Previous research showed that teaching high school and college students about the conventions of diagrams (COD) can improve diagrammatic reasoning. In this study, middle school science students received COD instruction…

The American High School

ERIC Educational Resources Information Center

Ediger, Marlow

2008-01-01

Of all levels of schooling, the high school receives by far the most criticism. There are continuous innovations recommended in journal articles, textbooks, and speeches at state/national conventions on ways to improve the secondary level of schooling. At one teacher education convention, the speaker was criticizing the American high school and…

Comparison of emerging contaminants in receiving waters downstream of a conventional wastewater treatment plant and a forest-water reuse system

EPA Science Inventory

Forest-water reuse (FWR) systems treat municipal, industrial, and agricultural wastewaters via land application to forest soils. Previous studies have shown that both large-scale conventional wastewater treatment plants (WWTPs) and FWR systems do not completely remove many contam...

Rupture Dynamics and Seismic Radiation on Rough Faults for Simulation-Based PSHA

NASA Astrophysics Data System (ADS)

Mai, P. M.; Galis, M.; Thingbaijam, K. K. S.; Vyas, J. C.; Dunham, E. M.

2017-12-01

Simulation-based ground-motion predictions may augment PSHA studies in data-poor regions or provide additional shaking estimations, incl. seismic waveforms, for critical facilities. Validation and calibration of such simulation approaches, based on observations and GMPE's, is important for engineering applications, while seismologists push to include the precise physics of the earthquake rupture process and seismic wave propagation in 3D heterogeneous Earth. Geological faults comprise both large-scale segmentation and small-scale roughness that determine the dynamics of the earthquake rupture process and its radiated seismic wavefield. We investigate how different parameterizations of fractal fault roughness affect the rupture evolution and resulting near-fault ground motions. Rupture incoherence induced by fault roughness generates realistic ω-2 decay for high-frequency displacement amplitude spectra. Waveform characteristics and GMPE-based comparisons corroborate that these rough-fault rupture simulations generate realistic synthetic seismogram for subsequent engineering application. Since dynamic rupture simulations are computationally expensive, we develop kinematic approximations that emulate the observed dynamics. Simplifying the rough-fault geometry, we find that perturbations in local moment tensor orientation are important, while perturbations in local source location are not. Thus, a planar fault can be assumed if the local strike, dip, and rake are maintained. The dynamic rake angle variations are anti-correlated with local dip angles. Based on a dynamically consistent Yoffe source-time function, we show that the seismic wavefield of the approximated kinematic rupture well reproduces the seismic radiation of the full dynamic source process. Our findings provide an innovative pseudo-dynamic source characterization that captures fault roughness effects on rupture dynamics. Including the correlations between kinematic source parameters, we present a new pseudo-dynamic rupture modeling approach for computing broadband ground-motion time-histories for simulation-based PSHA

Orthogonal cutting of laser beam melted parts

NASA Astrophysics Data System (ADS)

Götze, Elisa; Zanger, Frederik; Schulze, Volker

2018-05-01

The finishing process of parts manufactured by laser beam melting is of high concern due to the lack of surface accuracy. Therefore, the focus of this work lies on the influence of the build-up direction of the parts and their effect on the finishing process. The orthogonal cutting reveals findings in the fields of chip formation, involved forces and temperatures appearing during machining. In the investigations, the cutting depth was varied between 0.05 and 0.15 mm representing a finishing process and the cutting velocity ranges from 30 to 200 m/min depending on the material. The experiments contain the materials stainless steel (AISI 316L), titanium (Ti6Al4V) and nickel-base alloy (IN718). The two materials named latter are of high interest in the aerospace sector and at the same time titanium is used in the medical field due to its biocompatibility. For the materials IN718 and Ti6Al4V a negative rake angle of -7.5° and for stainless steel a rake angle of 12.5° are chosen for the cutting experiments. The results provide the base for processing strategies. Therefore, the specimens were solely laser beam melted without post-processing like heat treatment. The evaluation of the experiments shows that an increase in cutting speed has different effects depending on the material. For stainless steel the measured forces regarding the machining direction to the layers approach the same values. In contrast, the influence of the layers regarding the forces appearing during orthogonal cutting of the materials IN718 and Ti6Al4V differ for lower cutting speeds.

Childhood exposure to Libby amphibole during outdoor activities.

PubMed

Ryan, Patrick H; LeMasters, Grace K; Burkle, Jeffrey; Lockey, James E; Black, Brad; Rice, Carol

2015-01-01

Residents of Libby, MT were exposed to amphibole asbestos through multiple environmental pathways. Previous exposure characterization has primarily relied on qualitative report of these exposure activities. The objectives of this study were to describe available data from the US EPA preremediation actions for Libby amphibole (LA) exposure in Libby, MT and develop an approach to characterize outdoor residential exposure to LA among children. Homes in Libby, MT included in the US EPA preremediation Contaminant Screening Survey (CSS) were categorized by the presence of interior and/or exterior visible vermiculite and concentrations of LA were measured in samples of dust and soil. Airborne exposure to LA while digging/gardening, raking, and mowing were estimated using US EPA activity-based sampling (ABS) results. Residential histories and frequency/duration of childhood activities were combined with ABS to demonstrate the approach for estimating potential exposure. A total of 3154 residential properties participated in the CSS and 44% of these had visible exterior vermiculite. Airborne concentrations of LA where there was visible vermiculite outdoors were 3-15 times higher during digging/gardening, raking, and mowing activities compared with homes without visible outdoor vermiculite. Digging and gardening activities represented the greatest contribution to estimated exposures and 73% of the participants reported this activity before the age of 6 years. This methodology demonstrated the use of historical preremediation data to estimate residential exposures of children for specific activities. Children younger than age 6 years may have been exposed to LA while digging/gardening, especially at homes where there is visible outdoor vermiculite. This approach may be extended to other activities and applied to the entire cohort to examine health outcomes.

The 2016 Mihoub (north-central Algeria) earthquake sequence: Seismological and tectonic aspects

NASA Astrophysics Data System (ADS)

Khelif, M. F.; Yelles-Chaouche, A.; Benaissa, Z.; Semmane, F.; Beldjoudi, H.; Haned, A.; Issaadi, A.; Chami, A.; Chimouni, R.; Harbi, A.; Maouche, S.; Dabbouz, G.; Aidi, C.; Kherroubi, A.

2018-06-01

On 28 May 2016 at 23:54 (UTC), an Mw5.4 earthquake occurred in Mihoub village, Algeria, 60 km southeast of Algiers. This earthquake was the largest event in a sequence recorded from 10 April to 15 July 2016. In addition to the permanent national network, a temporary network was installed in the epicentral region after this shock. Recorded event locations allow us to give a general overview of the sequence and reveal the existence of two main fault segments. The first segment, on which the first event in the sequence was located, is near-vertical and trends E-W. The second fault plane, on which the largest event of the sequence was located, dips to the southeast and strikes NE-SW. A total of 46 well-constrained focal mechanisms were calculated. The events located on the E-W-striking fault segment show mainly right-lateral strike-slip (strike N70°E, dip 77° to the SSE, rake 150°). The events located on the NE-SW-striking segment show mainly reverse faulting (strike N60°E, dip 70° to the SE, rake 130°). We calculated the static stress change caused by the first event (Md4.9) of the sequence; the result shows that the fault plane of the largest event in the sequence (Mw5.4) and most of the aftershocks occurred within an area of increased Coulomb stress. Moreover, using the focal mechanisms calculated in this work, we estimated the orientations of the main axes of the local stress tensor ellipsoid. The results confirm previous findings that the general stress field in this area shows orientations aligned NNW-SSE to NW-SE. The 2016 Mihoub earthquake sequence study thus improves our understanding of seismic hazard in north-central Algeria.

Pitot survey of exhaust flow field of a 2-D scramjet nozzle at Mach 6 with air or freon and argon used for exhaust simulation

NASA Technical Reports Server (NTRS)

Monta, William J.

1992-01-01

A pitot-rake survey of the simulated exhaust of a half-span scramjet nozzle model was conducted in the Langley 20-Inch Mach 6 Tunnel to provide an additional data set for computational fluid dynamics (CFD) code comparisons. A wind-tunnel model was tested with a 26-tube pitot rake that could be manually positioned along the mid-semispan plane of the model. The model configuration had an external expansion surface of 20 degrees and an internal cowl expansion of 12 degrees; tests were also performed with a flow fence. Tests were conducted at a free-stream Reynolds number of approximately 6.5 x 10(exp 6) per foot and a model angle of attack of -0.75 degrees. The two exhaust gas mediums that were tested were air and a Freon 12-argon mixture. Each medium was tested at two jet total pressures at approximately 28 and 14 psia. This document presents the flow-field survey results in graphical as well as tabular form, and several observations concerning the results are discussed. The surveys reveal the major expected flow-field characteristics for each test configuration. For a 50-percent freon 12 and 50-percent argon mixture by volume (Fr-Ar), the exhaust jet pressures were slightly higher than those for air. The addition of a flow fence slightly raised the pitot pressure for the Fr-Ar mixture, but it produced little change for air. For the Fr-Ar exhaust, the plume was larger and the region between the shock wave and plume was smaller.

Teleseismic Body Wave Analysis for the 27 September 2003 Altai, Earthquake (Mw7.4) and Large Aftershocks

NASA Astrophysics Data System (ADS)

Gomez-Gonzalez, J. M.; Mellors, R.

2007-05-01

We investigate the kinematics of the rupture process for the September 27, 2003, Mw7.3, Altai earthquake and its associated large aftershocks. This is the largest earthquake striking the Altai mountains within the last 50 years, which provides important constraints on the ongoing tectonics. The fault plane solution obtained by teleseismic body waveform modeling indicated a predominantly strike-slip event (strike=130, dip=75, rake 170), Scalar moment for the main shock ranges from 0.688 to 1.196E+20 N m, a source duration of about 20 to 42 s, and an average centroid depth of 10 km. Source duration would indicate a fault length of about 130 - 270 km. The main shock was followed closely by two aftershocks (Mw5.7, Mw6.4) occurred the same day, another aftershock (Mw6.7) occurred on 1 October , 2003. We also modeled the second aftershock (Mw6.4) to asses geometric similarities during their respective rupture process. This aftershock occurred spatially very close to the mainshock and possesses a similar fault plane solution (strike=128, dip=71, rake=154), and centroid depth (13 km). Several local conditions, such as the crustal model and fault geometry, affect the correct estimation of some source parameters. We perfume a sensitivity evaluation of several parameters, including centroid depth, scalar moment and source duration, based on a point and finite source modeling. The point source approximation results are the departure parameters for the finite source exploration. We evaluate the different reported parameters to discard poor constrained models. In addition, deformation data acquired by InSAR are also included in the analysis.

Establishing repeatable operation of a centrifugal compressor research facility for aerodynamic investigations

NASA Astrophysics Data System (ADS)

Dolan, Matthew Philip

The objective of this research has been to analyze the steady state performance of a new centrifugal compressor research facility. The CSTAR (Centrifugal STage for Aerodynamic Research) compressor has been designed to be placed as the last stage in an axial compressor and its performance in this flow regime was measured. Because the compressor was designed as a research vehicle, unique instrumentation throughout the flow path provides a detailed look at its steady state performance. Rakes at the inlet and deswirl section quantify the overall performance but other instrumentation is used to understand the component performance. Static pressure taps along the shroud, within the diffuser, and through the turn-to-axial show the static pressure rise. Additionally, rakes at the inlet and exit of diffuser also characterize the performance of the wedge diffuser and the impeller. Additionally, capacitance probes located at the knee and exducer of the impeller non-intrusively measure the size of the tip clearance during facility operation. An investigation into these measurements resulted in a standard procedure for in-situ calibration and installation to produce repeatable and accurate clearance measurements. Finally, the feasibility of future Laser Doppler Velocimetry measurements acquired through the shroud window was tested and was found to be achievable with the use of beam translators to ensure that measurement volumes are created after beam refraction through the windows. Inlet conditions of the facility have been investigated and fluctuations of the ambient conditions have been mitigated with a large settling chamber to ensure repeatable and stable operation. The current instrumentation was utilized to determine the compressor performance. Measurements of the steady performance parameters along with those of the internal flowfield are documented.

Implementing virtual reality interfaces for the geosciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bethel, W.; Jacobsen, J.; Austin, A.

1996-06-01

For the past few years, a multidisciplinary team of computer and earth scientists at Lawrence Berkeley National Laboratory has been exploring the use of advanced user interfaces, commonly called {open_quotes}Virtual Reality{close_quotes} (VR), coupled with visualization and scientific computing software. Working closely with industry, these efforts have resulted in an environment in which VR technology is coupled with existing visualization and computational tools. VR technology may be thought of as a user interface. It is useful to think of a spectrum, ranging the gamut from command-line interfaces to completely immersive environments. In the former, one uses the keyboard to enter threemore » or six-dimensional parameters. In the latter, three or six-dimensional information is provided by trackers contained either in hand-held devices or attached to the user in some fashion, e.g. attached to a head-mounted display. Rich, extensible and often complex languages are a vehicle whereby the user controls parameters to manipulate object position and location in a virtual world, but the keyboard is the obstacle in that typing is cumbersome, error-prone and typically slow. In the latter, the user can interact with these parameters by means of motor skills which are highly developed. Two specific geoscience application areas will be highlighted. In the first, we have used VR technology to manipulate three-dimensional input parameters, such as the spatial location of injection or production wells in a reservoir simulator. In the second, we demonstrate how VR technology has been used to manipulate visualization tools, such as a tool for computing streamlines via manipulation of a {open_quotes}rake.{close_quotes} The rake is presented to the user in the form of a {open_quotes}virtual well{close_quotes} icon, and provides parameters used by the streamlines algorithm.« less

Design Architecture and Initial Results from an FPGA Based Digital Receiver for Multistatic Meteor Measurements

NASA Astrophysics Data System (ADS)

Palo, Scott; Vaudrin, Cody

Defined by a minimal RF front-end followed by an analog-to-digital converter (ADC) and con-trolled by a reconfigurable logic device (FPGA), the digital receiver will replace conventional heterodyning analog receivers currently in use by the COBRA meteor radar. A basic hardware overview touches on the major digital receiver components, theory of operation and data han-dling strategies. We address concerns within the community regarding the implementation of digital receivers in small-scale scientific radars, and outline the numerous benefits with a focus on reconfigurability. From a remote sensing viewpoint, having complete visibility into a band of the EM spectrum allows an experiment designer to focus on parameter estimation rather than hardware limitations. Finally, we show some basic multistatic receiver configurations enabled through GPS time synchronization. Currently, the digital receiver is configured to facilitate range and radial velocity determination of meteors in the MLT region for use with the COBRA meteor radar. Initial measurements from data acquired at Platteville, Colorado and Tierra Del Fuego in Argentina will be presented. We show an improvement in detection rates compared to conventional analog systems. Scientific justification for a digital receiver is clearly made by the presentation of RTI plots created using data acquired from the receiver. These plots reveal an interesting phenomenon concerning vacillating power structures in a select number of meteor trails.

Lipid profile in antipsychotic drug users: A comparative study

PubMed Central

Roohafza, Hamidreza; Khani, Azam; Afshar, Hamid; Garakyaraghi, Mohammad; Amirpour, Afshin; Ghodsi, Basir

2013-01-01

BACKGROUND Schizophrenic patients who receive antipsychotic drugs may be highly prone to metabolic disorders such as weight gain, dyslipidemia, and insulin resistance. The objective of the present study was to compare the effect of atypical and conventional antipsychotics on lipid profile. METHODS 128 schizophrenic patients were enrolled into the study. Patients were divided into two groups. One group had received one type of atypical antipsychotic drug, and, the other, one type of conventional antipsychotic drug. They were considered as atypical and conventional groups. Moreover, both groups had not used any other antipsychotic drugs during the past year. Demographic data and food frequency questionnaire were completed by the participants. Serum triglyceride, total cholesterol (TC), high-density lipoprotein and low-density lipoprotein (LDL) cholesterols, and apolipoprotein A and B (Apo B) were tested by blood sample drawing after 12 hours of fasting through the antecubital vein. Student’s t-test was used to compare atypical and conventional groups. RESULTS There was no significant difference in age, gender, duration of illness, period of drug consumption, and age at onset of illness in the two groups. Patients in the atypical group used clozapine and risperidone (46.9%) more than olanzapine. In the conventional group 81.3% of patients used phenothiazines. Comparison between lipid profile in the conventional and atypical groups showed a significantly higher mean in TC (P = 0.01), LDL (P = 0.03), and Apo B (P = 0.01) in conventional group than the atypical group. CONCLUSION In schizophrenic patients, the level of lipid profile had been increased in both atypical and conventional antipsychotic users, especially conventional users, so the effect of antipsychotic drugs should be investigated periodically. PMID:23766777

Incidence of Tardive Dyskinesia with Atypical and Conventional Antipsychotic Medications: Prospective Cohort Study

PubMed Central

Woods, Scott W.; Morgenstern, Hal; Saksa, John R.; Walsh, Barbara C.; Sullivan, Michelle C.; Money, Roy; Hawkins, Keith A.; Gueorguieva, Ralitza V.; Glazer, William M.

2011-01-01

Objective Most previous studies of the incidence of tardive dyskinesia with atypical compared to conventional antipsychotics have not had tardive dyskinesia as their primary focus. The current study aimed to compare the incidence of tardive dyskinesia with atypical vs. conventional antipsychotics using methods similar to those from a previous prospective cohort study at our site in the 1980s. Method 352 initially tardive dyskinesia-free psychiatric outpatients were examined for a new diagnosis of tardive dyskinesia every 6 months for up to 4 years at a community mental health center. At baseline, subjects were receiving conventional antipsychotics only (23%), atypicals only (64%), or both (14%). Only 26 subjects had never received conventional antipsychotics. Results Compared with subjects treated with conventional antipsychotics alone since the previous visit, the adjusted tardive dyskinesia incidence rate-ratio for subjects treated with atypical antipsychotics alone was 0.68 (95% confidence interval 0.29 to 1.64). The incidence and prevalence of tardive dyskinesia was similar to previous findings at this site in the 1980s. Conclusion The incidence of tardive dyskinesia with recent exposure to atypical antipsychotics alone was more similar to that for conventional antipsychotics than in most previous studies. Despite high penetration of atypical antipsychotics into clinical practice, the incidence and prevalence of tardive dyskinesia appeared relatively unchanged since the 1980s. Clinicians should continue to monitor for tardive dyskinesia, and researchers should continue to pursue efforts to treat or prevent it. PMID:20156410

Food selection and perceptions of chewing ability following provision of implant and conventional prostheses in complete denture wearers.

PubMed

Allen, Finbarr; McMillan, Anne

2002-06-01

The loss of natural teeth compromises chewing efficiency, and edentulous patients often have a diet that is deficient in fibre and vitamins. Prostheses that are retained on implants offer the possibility of overcoming some of the limitations of conventional dentures in terms of chewing efficiency. The aim of this study was to test the hypothesis that improvement in satisfaction with oral prostheses would result in improved food selection in edentulous patients. This prospective study involved three groups, namely (i) subjects who requested and received implants to stabilise a complete fixed or removable prosthesis (IG, n = 26), (ii) edentulous subjects who requested implant prostheses, but received conventional dentures (CDG1, n = 22), and (iii) edentulous subjects who requested and received conventional dentures (CDG2, n = 35). Data were collected using validated questionnaires pre- and postoperatively. Prior to treatment, all subjects were asked whether they ate a variety of hard and soft foods, to indicate the degree of difficulty they experienced when chewing these foods, and to rate their satisfaction with various aspects of their maxillary and mandibular complete dentures. Following the completion of treatment, subjects completed the questionnaires again. Pre- and postoperative data were compared. Subjects who received implant prostheses reported significant improvement in chewing hard and soft foods. CDG2 subjects also reported improvement, but CDG1 subjects reported no change or even deterioration following treatment. Despite reported improvement in satisfaction with comfort and ability to chew food, 30-50% of IG and CDG2 subjects still avoided eating foods such as carrot and apple. This suggests that, in the absence of tailored dietary advice, apparently successful prosthetic rehabilitation does not necessarily result in a satisfactory diet.

Using Marginal Structural Modeling to Estimate the Cumulative Impact of an Unconditional Tax Credit on Self-Rated Health.

PubMed

Pega, Frank; Blakely, Tony; Glymour, M Maria; Carter, Kristie N; Kawachi, Ichiro

2016-02-15

In previous studies, researchers estimated short-term relationships between financial credits and health outcomes using conventional regression analyses, but they did not account for time-varying confounders affected by prior treatment (CAPTs) or the credits' cumulative impacts over time. In this study, we examined the association between total number of years of receiving New Zealand's Family Tax Credit (FTC) and self-rated health (SRH) in 6,900 working-age parents using 7 waves of New Zealand longitudinal data (2002-2009). We conducted conventional linear regression analyses, both unadjusted and adjusted for time-invariant and time-varying confounders measured at baseline, and fitted marginal structural models (MSMs) that more fully adjusted for confounders, including CAPTs. Of all participants, 5.1%-6.8% received the FTC for 1-3 years and 1.8%-3.6% for 4-7 years. In unadjusted and adjusted conventional regression analyses, each additional year of receiving the FTC was associated with 0.033 (95% confidence interval (CI): -0.047, -0.019) and 0.026 (95% CI: -0.041, -0.010) units worse SRH (on a 5-unit scale). In the MSMs, the average causal treatment effect also reflected a small decrease in SRH (unstabilized weights: β = -0.039 unit, 95% CI: -0.058, -0.020; stabilized weights: β = -0.031 unit, 95% CI: -0.050, -0.007). Cumulatively receiving the FTC marginally reduced SRH. Conventional regression analyses and MSMs produced similar estimates, suggesting little bias from CAPTs. © The Author 2016. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Effectiveness of the Virtual Reality System Toyra on Upper Limb Function in People with Tetraplegia: A Pilot Randomized Clinical Trial.

PubMed

Dimbwadyo-Terrer, I; Gil-Agudo, A; Segura-Fragoso, A; de los Reyes-Guzmán, A; Trincado-Alonso, F; Piazza, S; Polonio-López, B

2016-01-01

The aim of this study was to investigate the effects of a virtual reality program combined with conventional therapy in upper limb function in people with tetraplegia and to provide data about patients' satisfaction with the virtual reality system. Thirty-one people with subacute complete cervical tetraplegia participated in the study. Experimental group received 15 sessions with Toyra(®) virtual reality system for 5 weeks, 30 minutes/day, 3 days/week in addition to conventional therapy, while control group only received conventional therapy. All patients were assessed at baseline, after intervention, and at three-month follow-up with a battery of clinical, functional, and satisfaction scales. Control group showed significant improvements in the manual muscle test (p = 0,043, partial η (2) = 0,22) in the follow-up evaluation. Both groups demonstrated clinical, but nonsignificant, changes to their arm function in 4 of the 5 scales used. All patients showed a high level of satisfaction with the virtual reality system. This study showed that virtual reality added to conventional therapy produces similar results in upper limb function compared to only conventional therapy. Moreover, the gaming aspects incorporated in conventional rehabilitation appear to produce high motivation during execution of the assigned tasks. This trial is registered with EudraCT number 2015-002157-35.

Effectiveness of the Virtual Reality System Toyra on Upper Limb Function in People with Tetraplegia: A Pilot Randomized Clinical Trial

PubMed Central

Dimbwadyo-Terrer, I.; Gil-Agudo, A.; Segura-Fragoso, A.; de los Reyes-Guzmán, A.; Trincado-Alonso, F.; Piazza, S.; Polonio-López, B.

2016-01-01

The aim of this study was to investigate the effects of a virtual reality program combined with conventional therapy in upper limb function in people with tetraplegia and to provide data about patients' satisfaction with the virtual reality system. Thirty-one people with subacute complete cervical tetraplegia participated in the study. Experimental group received 15 sessions with Toyra® virtual reality system for 5 weeks, 30 minutes/day, 3 days/week in addition to conventional therapy, while control group only received conventional therapy. All patients were assessed at baseline, after intervention, and at three-month follow-up with a battery of clinical, functional, and satisfaction scales. Control group showed significant improvements in the manual muscle test (p = 0,043, partial η 2 = 0,22) in the follow-up evaluation. Both groups demonstrated clinical, but nonsignificant, changes to their arm function in 4 of the 5 scales used. All patients showed a high level of satisfaction with the virtual reality system. This study showed that virtual reality added to conventional therapy produces similar results in upper limb function compared to only conventional therapy. Moreover, the gaming aspects incorporated in conventional rehabilitation appear to produce high motivation during execution of the assigned tasks. This trial is registered with EudraCT number 2015-002157-35. PMID:26885511

The early psychological adjustment of cleft patients after maxillary distraction osteogenesis and conventional orthognathic surgery: a preliminary study.

PubMed

Cheung, Lim Kwong; Loh, John Ser Pheng; Ho, Samuel M Y

2006-12-01

To compare the early psychological changes of cleft lip and palate (CLP) and noncleft patients after maxillofacial corrective surgery, including maxillary distraction osteogenesis and conventional orthognathic surgery. Nine CLP patients were compared with a group of 9 non-CLP patients having similar dentofacial deformities in a prospective longitudinal cohort study. Five of the CLP patients underwent maxillary distraction osteogenesis and 4 underwent conventional orthognathic surgery. A control group of 9 noncleft patients received conventional orthognathic surgery. All patients completed a set of questionnaires to enable their psychological profile to be assessed. The data were collected immediately before surgery (T1), and at 3 weeks (T2) and 12 weeks (T3) after surgery. The CLP patients treated with distraction osteogenesis were happier, but had a higher level of social anxiety and distress than the CLP patients receiving conventional orthognathic surgery. On the other hand, the CLP patients overall were happier, with lower social anxiety and distress, than the noncleft control group. The CLP patients showed a higher level of parental self-esteem than the noncleft patients. This preliminary study shows that CLP patients were generally happier, and had a higher level of parental support, than normal patients suffering from dentofacial deformities. Maxillary distraction osteogenesis seemed to induce a higher level of anxiety and distress in CLP patients than conventional orthognathic surgery in both cleft and noncleft patients.

COMBINED SEWER OVERFLOW - BALANCING FLOW FOR CSO ABATEMENT

EPA Science Inventory

Instead of using conventional storage units, e.g., reinforced concrete tanks and lined earthen basins, which are relatively expensive and require a lot of urban land area, the in-receiving water flow balance method (FBM) facilities use the receiving water body itself for storage ...

Efficacy and safety of a 14-day administration of tolvaptan in the treatment of patients with ascites in hepatic oedema.

PubMed

Sakaida, Isao; Yamashita, Satoyoshi; Kobayashi, Tomoo; Komatsu, Masafumi; Sakai, Terufumi; Komorizono, Yasuji; Okada, Mitsuru; Okita, Kiwamu

2013-06-01

To investigate the efficacy and safety of 14 days' orally administered tolvaptan as adjunctive treatment for hepatic oedema in Japanese liver cirrhosis patients with insufficient response to conventional diuretics, with the option to increase dose in those who did not respond initially. This multicentre, single-arm, phase 3 study allocated patients with liver cirrhosis and persistent ascites to 7-day treatment with 7.5 mg/day tolvaptan followed by an additional 7 days' treatment. Responders at day 7 (achieving ≥ 1 kg body-weight reduction) continued on 7.5 mg/day tolvaptan; nonresponders (<1 kg body-weight reduction) received 15 mg/day tolvaptan. Conventional diuretic treatment continued throughout. The primary endpoint was change in body weight from baseline, as a marker of ascites volume. A total of 51 patients received 7.5 mg/day tolvaptan for 7 days, which caused a significant reduction in mean body weight (55% response rate). During the second 7-day treatment period, 30 patients received 7.5 mg/day tolvaptan and 13 patients received tolvaptan 15 mg/day: response rates were 43% and 23%, respectively. Two serious adverse events were observed. Serum sodium was within normal range. Tolvaptan therapy for 14 days (with possible dose increase as necessary), in combination with conventional diuretics, effectively reduced body weight in patients with hepatic oedema.

Self-Harm and Conventional Gender Roles in Women

ERIC Educational Resources Information Center

Straiton, Melanie L.; Hjelmeland, Heidi; Grimholt, Tine K.; Dieserud, Gudrun

2013-01-01

A total of thirty-two women admitted to a general hospital for medical treatment after self-harming completed measures of conventional positive and negative masculinity and femininity. Comparisons were made with two control groups with no self-harm history; 33 women receiving psychiatric outpatient treatment and a nonclinical sample of 206 women.…

Astronaut John Young collecting samples at North Ray crater during EVA

NASA Image and Video Library

1972-04-23

AS16-117-18826 (23 April 1972) --- Astronaut John W. Young collects samples at the North Ray Crater geological site during the mission's third and final Apollo 16 extravehicular activity (EVA). He has a rake in his hand, and the gnomon is near his foot. Note how soiled Young's Extravehicular Mobility Unit (EMU) is. While astronauts Young, commander; and Charles M. Duke Jr., lunar module pilot; descended in the Apollo 16 Lunar Module (LM) "Orion" to explore the Descartes highlands landing site on the moon, astronaut Thomas K. Mattingly II, command module pilot, remained with the Command and Service Modules (CSM) "Casper" in lunar orbit.

Optical Cryogenic Tank Level Sensor

NASA Technical Reports Server (NTRS)

Duffell, Amanda

2005-01-01

Cryogenic fluids play an important role in space transportation. Liquid oxygen and hydrogen are vital fuel components for liquid rocket engines. It is also difficult to accurately measure the liquid level in the cryogenic tanks containing the liquids. The current methods use thermocouple rakes, floats, or sonic meters to measure tank level. Thermocouples have problems examining the boundary between the boiling liquid and the gas inside the tanks. They are also slow to respond to temperature changes. Sonic meters need to be mounted inside the tank, but still above the liquid level. This causes problems for full tanks, or tanks that are being rotated to lie on their side.

Sidewall Mach Number Distributions for the NASA Langley Transonic Dynamics Tunnel

NASA Technical Reports Server (NTRS)

Florance, James R.; Rivera, Jose A., Jr.

2001-01-01

The Transonic Dynamics Tunnel(TDT) was recalibrated due to the conversion of the heavy gas test medium from R-12 to R-134a. The objectives of the tests were to determine the relationship between the free-stream Mach number and the measured test section Mach number, and to quantify any necessary corrections. Other tests included the measurement of pressure distributions along the test-section walls, test-section centerline, at certain tunnel stations via a rake apparatus, and in the tunnel settling chamber. Wall boundary layer, turbulence, and flow angularity measurements were also performed. This paper discusses the determination of sidewall Mach number distributions.

Study of the Effects of Centrifugal Instabilities on Flow in a 40 to 1 Aspect Ratio Rectangular Curved Channel, for Dean Numbers from 35 to Fully Turbulent Conditions

DTIC Science & Technology

1990-12-01

is constructed from stainless steel hypodermic tubing with inner and outer diameters of 0.203 mm and 0.406 mm. The five tubes were first joined by...for all channels is 256 kHz. A schematic diagram of the measurement process [Ref. 25] is given in Figure 78, and is also described below. The analog...and smoke rake. Combustion takes place inside a 40.64 cm long, 6.27 cm inside diameter (2.5 inch schedule 40) steel pipe. Inside this chamber, smoke is

Computations and turbulent flow modeling in support of helicopter rotor technology

NASA Technical Reports Server (NTRS)

Rose, W. C.

1985-01-01

The angle of attack (AOA) tandem cavity wind tunnel experiment was prepared. Actual wind tunnel testing started shortly after the beginning of 1985. A multi-probe aerodynamic rake was designed and installed for use in surveying the shear layers present over the open cavity on the Kuiper Airborne Observatory (KAO). The nature of the behavior of the thermal environment within the KAO cavity at operational altitudes was determined. Assistance was given in the design of the cavity for the University of Denver radiometer. Attempts to distinguish between the optical terms of blur circle size (or image size) and the term due to jitter were discussed.

Techniques used in the F-14 variable-sweep transition flight experiment

NASA Technical Reports Server (NTRS)

Anderson, Bianca Trujillo; Meyer, Robert R., Jr.; Chiles, Harry R.

1988-01-01

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system; (2) two boundary-layer rakes; (3) surface pitot tubes; and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.

An Investigation of the McDonnell XP-85 Airplane in the Ames 40- by 80-Foot Wind Tunnel: Pressure-Distribution Tests

NASA Technical Reports Server (NTRS)

Hunton, Lynn W.; James, Harry A.

1948-01-01

Pressure measurements were made during wind-tunnel tests of the McDonnell XP-85 parasite fighter. Static-pressure orifices were located over the fuselage nose, over the canopy, along the wing root, and along the upper and lower stabilizer roots. A total-pressure and static-pressure rake was located in the turbojet engine air-intake duct. It was installed at the station where the compressor face would be located. Pressure data were obtained for two airplane conditions, clean and with skyhook extended, through a range of angle of attack and a range of yaw.

Improving Passive Time Reversal Underwater Acoustic Communications Using Subarray Processing.

PubMed

He, Chengbing; Jing, Lianyou; Xi, Rui; Li, Qinyuan; Zhang, Qunfei

2017-04-24

Multichannel receivers are usually employed in high-rate underwater acoustic communication to achieve spatial diversity. In the context of multichannel underwater acoustic communications, passive time reversal (TR) combined with a single-channel adaptive decision feedback equalizer (TR-DFE) is a low-complexity solution to achieve both spatial and temporal focusing. In this paper, we present a novel receiver structure to combine passive time reversal with a low-order multichannel adaptive decision feedback equalizer (TR-MC-DFE) to improve the performance of the conventional TR-DFE. First, the proposed method divides the whole received array into several subarrays. Second, we conduct passive time reversal processing in each subarray. Third, the multiple subarray outputs are equalized with a low-order multichannel DFE. We also investigated different channel estimation methods, including least squares (LS), orthogonal matching pursuit (OMP), and improved proportionate normalized least mean squares (IPNLMS). The bit error rate (BER) and output signal-to-noise ratio (SNR) performances of the receiver algorithms are evaluated using simulation and real data collected in a lake experiment. The source-receiver range is 7.4 km, and the data rate with quadrature phase shift keying (QPSK) signal is 8 kbits/s. The uncoded BER of the single input multiple output (SIMO) systems varies between 1 × 10 - 1 and 2 × 10 - 2 for the conventional TR-DFE, and between 1 × 10 - 2 and 1 × 10 - 3 for the proposed TR-MC-DFE when eight hydrophones are utilized. Compared to conventional TR-DFE, the average output SNR of the experimental data is enhanced by 3 dB.

Improving Passive Time Reversal Underwater Acoustic Communications Using Subarray Processing

PubMed Central

He, Chengbing; Jing, Lianyou; Xi, Rui; Li, Qinyuan; Zhang, Qunfei

2017-01-01

Multichannel receivers are usually employed in high-rate underwater acoustic communication to achieve spatial diversity. In the context of multichannel underwater acoustic communications, passive time reversal (TR) combined with a single-channel adaptive decision feedback equalizer (TR-DFE) is a low-complexity solution to achieve both spatial and temporal focusing. In this paper, we present a novel receiver structure to combine passive time reversal with a low-order multichannel adaptive decision feedback equalizer (TR-MC-DFE) to improve the performance of the conventional TR-DFE. First, the proposed method divides the whole received array into several subarrays. Second, we conduct passive time reversal processing in each subarray. Third, the multiple subarray outputs are equalized with a low-order multichannel DFE. We also investigated different channel estimation methods, including least squares (LS), orthogonal matching pursuit (OMP), and improved proportionate normalized least mean squares (IPNLMS). The bit error rate (BER) and output signal-to-noise ratio (SNR) performances of the receiver algorithms are evaluated using simulation and real data collected in a lake experiment. The source-receiver range is 7.4 km, and the data rate with quadrature phase shift keying (QPSK) signal is 8 kbits/s. The uncoded BER of the single input multiple output (SIMO) systems varies between 1×10−1 and 2×10−2 for the conventional TR-DFE, and between 1×10−2 and 1×10−3 for the proposed TR-MC-DFE when eight hydrophones are utilized. Compared to conventional TR-DFE, the average output SNR of the experimental data is enhanced by 3 dB. PMID:28441763

How to sell coal without penalties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gould, G.

1977-06-01

The total heat content of a coal shipment is a constant, not a variable quantity. This provides the cornerstone of a fundamentally sound concept that could replace the conventional as-received Btu concept. It is the CEC Btu concept, the Constant Energy Content, to distinguish it from the conventional as-received Btu concept. There are several major advantages of the CEC Btu concept: It denies the fallacies of conventional as-received Btu concepts and will thus diminish the potentials for error arising out of such misconceptions as well as avoid the pyschological handicap of penalty thinking. It should simplify reaching agreement on pricemore » and quality. It provides the opportunity for buyer and seller to share equitably in the costs of transporting the non-commodity water in a way that is readily observable and accountable. It places correct emphasis on the need for weighing and sampling the coal simultaneously enough to preclude material change in moisture content between the two events. It should not be difficult to implement because the means in many cases are at hand, it requires no change in laboratory analysis or reporting of results and evaluation of competitive values on a cost per million Btu basis is already common practice.« less

Comparison of Radiation-Induced Normal Lung Tissue Density Changes for Patients From Multiple Institutions Receiving Conventional or Hypofractionated Treatments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diot, Quentin, E-mail: quentin.diot@ucdenver.edu; Marks, Lawrence B.; Bentzen, Soren M.

Purpose: To quantitatively assess changes in computed tomography (CT)–defined normal lung tissue density after conventional and hypofractionated radiation therapy (RT). Methods and Materials: The pre-RT and post-RT CT scans from 118 and 111 patients receiving conventional and hypofractionated RT, respectively, at 3 institutions were registered to each other and to the 3-dimensional dose distribution to quantify dose-dependent changes in normal lung tissue density. Dose-response curves (DRC) for groups of patients receiving conventional and hypofractionated RT were generated for each institution, and the frequency of density changes >80 Hounsfield Units (HU) was modeled depending on the fractionation type using a Probitmore » model for different follow-up times. Results: For the pooled data from all institutions, there were significant differences in the DRC between the conventional and hypofractionated groups; the respective doses resulting in 50% complication risk (TD{sub 50}) were 62 Gy (95% confidence interval [CI] 57-67) versus 36 Gy (CI 33-39) at <6 months, 48 Gy (CI 46-51) versus 31 Gy (CI 28-33) at 6-12 months, and 47 Gy (CI 45-49) versus 35 Gy (32-37) at >12 months. The corresponding m values (slope of the DRC) were 0.52 (CI 0.46-0.59) versus 0.31 (CI 0.28-0.34) at <6 months, 0.46 (CI 0.42-0.51) versus 0.30 (CI 0.26-0.34) at 6-12 months, and 0.45 (CI 0.42-0.50) versus 0.31 (CI 0.27-0.35) at >12 months (P<.05 for all comparisons). Conclusion: Compared with conventional fractionation, hypofractionation has a lower TD{sub 50} and m value, both suggesting an increased degree of normal tissue density sensitivity with hypofractionation.« less

Comparison of Three Non-Imaging Angle-Diversity Receivers as Input Sensors of Nodes for Indoor Infrared Wireless Sensor Networks: Theory and Simulation

PubMed Central

Mendoza, Beatriz R.; Rodríguez, Silvestre; Pérez-Jiménez, Rafael; Ayala, Alejandro; González, Oswaldo

2016-01-01

In general, the use of angle-diversity receivers makes it possible to reduce the impact of ambient light noise, path loss and multipath distortion, in part by exploiting the fact that they often receive the desired signal from different directions. Angle-diversity detection can be performed using a composite receiver with multiple detector elements looking in different directions. These are called non-imaging angle-diversity receivers. In this paper, a comparison of three non-imaging angle-diversity receivers as input sensors of nodes for an indoor infrared (IR) wireless sensor network is presented. The receivers considered are the conventional angle-diversity receiver (CDR), the sectored angle-diversity receiver (SDR), and the self-orienting receiver (SOR), which have been proposed or studied by research groups in Spain. To this end, the effective signal-collection area of the three receivers is modelled and a Monte-Carlo-based ray-tracing algorithm is implemented which allows us to investigate the effect on the signal to noise ratio and main IR channel parameters, such as path loss and rms delay spread, of using the three receivers in conjunction with different combination techniques in IR links operating at low bit rates. Based on the results of the simulations, we show that the use of a conventional angle-diversity receiver in conjunction with the equal-gain combining technique provides the solution with the best signal to noise ratio, the lowest computational capacity and the lowest transmitted power requirements, which comprise the main limitations for sensor nodes in an indoor infrared wireless sensor network. PMID:27428966

A Randomized Trial of Phototherapy with Filtered Sunlight in African Neonates.

PubMed

Slusher, Tina M; Olusanya, Bolajoko O; Vreman, Hendrik J; Brearley, Ann M; Vaucher, Yvonne E; Lund, Troy C; Wong, Ronald J; Emokpae, Abieyuwa A; Stevenson, David K

2015-09-17

Sequelae of severe neonatal hyperbilirubinemia constitute a substantial disease burden in areas where effective conventional phototherapy is unavailable. We previously found that the use of filtered sunlight for the purpose of phototherapy is a safe and efficacious method for reducing total bilirubin. However, its relative safety and efficacy as compared with conventional phototherapy are unknown. We conducted a randomized, controlled noninferiority trial in which filtered sunlight was compared with conventional phototherapy for the treatment of hyperbilirubinemia in term and late-preterm neonates in a large, urban Nigerian maternity hospital. The primary end point was efficacy, which was defined as a rate of increase in total serum bilirubin of less than 0.2 mg per deciliter per hour for infants up to 72 hours of age or a decrease in total serum bilirubin for infants older than 72 hours of age who received at least 5 hours of phototherapy; we prespecified a noninferiority margin of 10% for the difference in efficacy rates between groups. The need for an exchange transfusion was a secondary end point. We also assessed safety, which was defined as the absence of the need to withdraw therapy because of hyperthermia, hypothermia, dehydration, or sunburn. We enrolled 447 infants and randomly assigned 224 to filtered sunlight and 223 to conventional phototherapy. Filtered sunlight was efficacious on 93% of treatment days that could be evaluated, as compared with 90% for conventional phototherapy, and had a higher mean level of irradiance (40 vs. 17 μW per square centimeter per nanometer, P<0.001). Temperatures higher than 38.0°C occurred in 5% of the infants receiving filtered sunlight and in 1% of those receiving conventional phototherapy (P<0.001), but no infant met the criteria for withdrawal from the study for reasons of safety or required an exchange transfusion. Filtered sunlight was noninferior to conventional phototherapy for the treatment of neonatal hyperbilirubinemia and did not result in any study withdrawals for reasons of safety. (Funded by the Thrasher Research Fund, Salt Lake City, and the National Center for Advancing Translational Sciences of the National Institutes of Health; Clinical Trials.gov number, NCT01434810.).

Efficacy of adding the Kinesio Taping method to guideline-endorsed conventional physiotherapy in patients with chronic nonspecific low back pain: a randomised controlled trial.

PubMed

Added, Marco Aurélio Nemitalla; Costa, Leonardo Oliveira Pena; Fukuda, Thiago Yukio; de Freitas, Diego Galace; Salomão, Evelyn Cassia; Monteiro, Renan Lima; Costa, Lucíola da Cunha Menezes

2013-10-24

Chronic nonspecific low back pain is a significant health condition with high prevalence worldwide and it is associated with enormous costs to society. Clinical practice guidelines show that many interventions are available to treat patients with chronic low back pain, but the vast majority of these interventions have a modest effect in reducing pain and disability. An intervention that has been widespread in recent years is the use of elastic bandages called Kinesio Taping. Although Kinesio Taping has been used extensively in clinical practice, current evidence does not support the use of this intervention; however these conclusions are based on a small number of underpowered studies. Therefore, questions remain about the effectiveness of the Kinesio Taping method as an additional treatment to interventions, such as conventional physiotherapy, that have already been recommended by the current clinical practice guidelines in robust and high-quality randomised controlled trials. We aim to determine the effectiveness of the addition of the use of Kinesio Taping in patients with chronic nonspecific low back pain who receive guideline-endorsed conventional physiotherapy. One hundred and forty-eight patients will be randomly allocated to receive either conventional physiotherapy, which consists of a combination of manual therapy techniques, general exercises, and specific stabilisation exercises (Guideline-Endorsed Conventional Physiotherapy Group) or to receive conventional physiotherapy with the addition of Kinesio Taping to the lumbar spine (Conventional Physiotherapy plus Kinesio Taping Group) over a period of 5 weeks (10 sessions of treatment). Clinical outcomes (pain intensity, disability and global perceived effect) will be collected at baseline and at 5 weeks, 3 months, and 6 months after randomisation. We will also collect satisfaction with care and adverse effects after treatment. Data will be collected by a blinded assessor. All statistical analysis will be conducted following the principles of intention to treat, and the effects of treatment will be calculated using Linear Mixed Models. The results of this study will provide new information about the usefulness of Kinesio Taping as an additional component of a guideline-endorsed physiotherapy program in patients with chronic nonspecific low back pain.

Dosimetric quality endpoints for low-dose-rate prostate brachytherapy using biological effective dose (bed) vs. conventional dose

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Rachana; Al-Hallaq, Hania; Pelizzari, Charles A.

2003-12-31

The purpose of this study was to compare conventional low-dose-rate prostate brachytherapy dosimetric quality parameters with their biological effective dose (BED) counterparts. To validate a model for transformation from conventional dose to BED, the postimplant plans of 31 prostate brachytherapy patients were evaluated using conventional dose-volume histogram (DVH) quality endpoints and analogous BED-DVH endpoints. Based on CT scans obtained 4 weeks after implantation, DVHs were computed and standard dosimetric endpoints V100 (volume receiving 100% of the prescribed dose), V150, V200, HI (1-[V150/V100]), and D90 (dose that 90% of the target volume received) were obtained for quality analysis. Using known andmore » reported transformations, dose grids were transformed to BED-early ({alpha}/{beta} = 10 Gy) and BED-late ({alpha}/{beta} = 3 Gy) grids, and the same dosimetric endpoints were analyzed. For conventional, BED-early and BED-late DVHs, no differences in V100 were seen (0.896, 0.893, and 0.894, respectively). However, V150 and V200 were significantly higher for both BED-early (0.582 and 0.316) and BED-late (0.595 and 0.337), compared with the conventional (0.539 and 0.255) DVHs. D90 was significantly lower for the BED-early (103.1 Gy) and BED-late transformations (106.9 Gy) as compared with the conventional (119.5 Gy) DVHs. The conventional prescription parameter V100 is the same for the corresponding BED-early and BED-late transformed DVHs. The toxicity parameters V150 and V200 are slightly higher using the BED transformations, suggesting that the BED doses are somewhat higher than predicted using conventional DVHs. The prescription/quality parameter D90 is slightly lower, implying that target coverage is lower than predicted using conventional DVHs. This methodology can be applied to analyze BED dosimetric endpoints to improve clinical outcome and reduce complications of prostate brachytherapy.« less

Free-space coherent optical communication receivers implemented with photorefractive optical beam combiners

NASA Technical Reports Server (NTRS)

Davidson, Frederic M.

1992-01-01

Performance measurements are reported concerning a coherent optical communication receiver that contained an iron doped indium phosphide photorefractive beam combiner, rather than a conventional optical beam splitter. The system obtained a bit error probability of 10(exp -6) at received signal powers corresponding to less than 100 detected photons per bit. The system used phase modulated Nd:YAG laser light at a wavelength of 1.06 microns.

Application of Renyi entropy for ultrasonic molecular imaging.

PubMed

Hughes, M S; Marsh, J N; Arbeit, J M; Neumann, R G; Fuhrhop, R W; Wallace, K D; Thomas, L; Smith, J; Agyem, K; Lanza, G M; Wickline, S A; McCarthy, J E

2009-05-01

Previous work has demonstrated that a signal receiver based on a limiting form of the Shannon entropy is, in certain settings, more sensitive to subtle changes in scattering architecture than conventional energy-based signal receivers [M. S. Hughes et al., J. Acoust. Soc. Am. 121, 3542-3557 (2007)]. In this paper new results are presented demonstrating further improvements in sensitivity using a signal receiver based on the Renyi entropy.

Repeated high-dose chemotherapy followed by purged autologous bone marrow transplantation as consolidation therapy in metastatic neuroblastoma.

PubMed

Hartmann, O; Benhamou, E; Beaujean, F; Kalifa, C; Lejars, O; Patte, C; Behard, C; Flamant, F; Thyss, A; Deville, A

1987-08-01

Among 62 children over 1 year of age at diagnosis, who were treated for stage IV neuroblastoma, 33 entered complete remission (CR) or good partial remission (GPR) after conventional therapy and received high-dose chemotherapy (HDC) with in vitro purged autologous bone marrow transplantation (ABMT) as consolidation therapy. The HDC was a combination of carmustine (BCNU), teniposide (VM-26), and melphalan. Thirty-three patients received one course of this regimen, and 18 received two courses. At present, 16 of the 33 grafted patients are alive in continuous CR, with a median follow-up of 28 months. Toxicity of this regimen was tolerable, principally marked by bone marrow depression and gastrointestinal (GI) tract complications. Four complication-related deaths were observed. Relapse post-ABMT occurred most often in the bone marrow. Under this treatment, actuarial disease-free survival is improved compared with that observed under conventional therapy.

Work-related medical rehabilitation in patients with musculoskeletal disorders: the protocol of a propensity score matched effectiveness study (EVA-WMR, DRKS00009780).

PubMed

Neuderth, Silke; Schwarz, Betje; Gerlich, Christian; Schuler, Michael; Markus, Miriam; Bethge, Matthias

2016-08-17

Musculoskeletal disorders are one of the most important causes of work disability. Various rehabilitation services and return-to-work programs have been developed in order to reduce sickness absence and increase sustainable return-to-work. As the effects of conventional medical rehabilitation programs on sickness absence duration were shown to be slight, work-related medical rehabilitation programs have been developed and tested. While such studies proved the efficacy of work-related medical rehabilitation compared with conventional medical rehabilitation in well-conducted randomized controlled trials, its effectiveness under real-life conditions has yet to be proved. The cohort study will be performed under real-life conditions with two parallel groups. Participants will receive either a conventional or a work-related medical rehabilitation program. Propensity score matching will be used to identify controls that are comparable to treated work-related medical rehabilitation patients. Over a period of three months, about 18,000 insured patients with permission to undergo a musculoskeletal rehabilitation program will be contacted. Of these, 15,000 will receive a conventional and 3,000 a work-related medical rehabilitation. We expect a participation rate of 40 % at baseline. Patients will be aged 18 to 65 years and have chronic musculoskeletal disorders, usually back pain. The control group will receive a conventional medical rehabilitation program without any explicit focus on work, work ability and return to work in diagnostics and therapy. The intervention group will receive a work-related medical rehabilitation program that in addition to common rehabilitation treatments contains 11 to 25 h of work-related treatment modules. Follow-up data will be assessed three and ten months after patients' discharge from the rehabilitation center. Additionally, department characteristics will be assessed and administrative data records used. The primary outcomes are sick leave duration, stable return to work and subjective work ability. Secondary outcomes cover several dimensions of health, functioning and coping strategies. This study will determine the relative effectiveness of a complex, newly implemented work-related rehabilitation strategy for patients with musculoskeletal disorders. German Clinical Trials Register ( DRKS00009780 , February 10, 2016).

Jackknife variance of the partial area under the empirical receiver operating characteristic curve.

PubMed

Bandos, Andriy I; Guo, Ben; Gur, David

2017-04-01

Receiver operating characteristic analysis provides an important methodology for assessing traditional (e.g., imaging technologies and clinical practices) and new (e.g., genomic studies, biomarker development) diagnostic problems. The area under the clinically/practically relevant part of the receiver operating characteristic curve (partial area or partial area under the receiver operating characteristic curve) is an important performance index summarizing diagnostic accuracy at multiple operating points (decision thresholds) that are relevant to actual clinical practice. A robust estimate of the partial area under the receiver operating characteristic curve is provided by the area under the corresponding part of the empirical receiver operating characteristic curve. We derive a closed-form expression for the jackknife variance of the partial area under the empirical receiver operating characteristic curve. Using the derived analytical expression, we investigate the differences between the jackknife variance and a conventional variance estimator. The relative properties in finite samples are demonstrated in a simulation study. The developed formula enables an easy way to estimate the variance of the empirical partial area under the receiver operating characteristic curve, thereby substantially reducing the computation burden, and provides important insight into the structure of the variability. We demonstrate that when compared with the conventional approach, the jackknife variance has substantially smaller bias, and leads to a more appropriate type I error rate of the Wald-type test. The use of the jackknife variance is illustrated in the analysis of a data set from a diagnostic imaging study.

Retrospective cohort study of diabetes mellitus and antipsychotic treatment in a geriatric population in the United States.

PubMed

Feldman, Peter D; Hay, Linda K; Deberdt, Walter; Kennedy, John S; Hutchins, David S; Hay, Donald P; Hardy, Thomas A; Hoffmann, Vicki P; Hornbuckle, Kenneth; Breier, Alan

2004-01-01

The objective of this study was to investigate risk of diabetes among elderly patients during treatment with antipsychotic medications. We conducted a longitudinal, retrospective study assessing the incidence of new prescription claims for antihyperglycemic agents during antipsychotic therapy. Prescription claims from the AdvancePCS claim database were followed for 6 to 9 months. Study participants consisted of patients in the United States aged 60+ and receiving antipsychotic monotherapy. The following cohorts were studied: an elderly reference population (no antipsychotics: n = 1,836,799), those receiving haloperidol (n = 6481) or thioridazine (n = 1658); all patients receiving any conventional antipsychotic monotherapy (n = 11,546), clozapine (n = 117), olanzapine (n = 5382), quetiapine (n = 1664), and risperidone (n = 12,244), and all patients receiving any atypical antipsychotic monotherapy (n = 19,407). We used Cox proportional hazards regression to determine the risk ratio of diabetes for antipsychotic cohorts relative to the reference population. Covariates included sex and exposure duration. New antihyperglycemic prescription rates were higher in each antipsychotic cohort than in the reference population. Overall rates were no different between atypical and conventional antipsychotic cohorts. Among individual antipsychotic cohorts, rates were highest among patients treated with thioridazine (95% confidence interval [CI], 3.1- 5.7), lowest with quetiapine (95% CI, 1.3-2.9), and intermediate with haloperidol, olanzapine, and risperidone. Among atypical cohorts, only risperidone users had a significantly higher risk (95% CI, 1.05-1.60; P = 0.016) than for haloperidol. Conclusions about clozapine were hampered by the low number of patients. These data suggest that diabetes risk is elevated among elderly patients receiving antipsychotic treatment. However, causality remains to be demonstrated. As a group, the risk for atypical antipsychotic users was not significantly different than for users of conventional antipsychotics.

Respiratory source control using surgical masks with nanofiber media.

PubMed

Skaria, Shaji D; Smaldone, Gerald C

2014-07-01

Potentially infected individuals ('source') are sometimes encouraged to use face masks to reduce exposure of their infectious aerosols to others ('receiver'). To improve compliance with Respiratory Source Control via face mask and therefore reduce receiver exposure, a mask should be comfortable and effective. We tested a novel face mask designed to improve breathability and filtration using nanofiber filtration. Using radiolabeled test aerosols and a calibrated exposure chamber simulating source to receiver interaction, facepiece function was measured with a life-like ventilated manikin model. Measurements included mask airflow resistance (pressure difference during breathing), filtration, (mask capture of exhaled radiolabeled test aerosols), and exposure (the transfer of 'infectious' aerosols from the 'source' to a 'receiver'). Polydisperse aerosols were measured at the source with a mass median aerodynamic diameter of 0.95 µm. Approximately 90% of the particles were <2.0 µm. Tested facepieces included nanofiber prototype surgical masks, conventional surgical masks, and for comparison, an N95-class filtering facepiece respirator (commonly known as an 'N95 respirator'). Airflow through and around conventional surgical face mask and nanofiber prototype face mask was visualized using Schlieren optical imaging. Airflow resistance [ΔP, cmH2O] across sealed surgical masks (means: 0.1865 and 0.1791 cmH2O) approached that of the N95 (mean: 0.2664 cmH2O). The airflow resistance across the nanofiber face mask whether sealed or not sealed (0.0504 and 0.0311 cmH2O) was significantly reduced in comparison. In addition, 'infected' source airflow filtration and receiver exposure levels for nanofiber face masks placed on the source were comparable to that achieved with N95 placed on the source; 98.98% versus 82.68% and 0.0194 versus 0.0557, respectively. Compared to deflection within and around the conventional face masks, Schlieren optical imaging demonstrated enhanced airflow through the nanofiber mask. Substituting nanofiber for conventional filter media significantly reduced face mask airflow resistance directing more airflow through the face mask resulting in enhanced filtration. Respiratory source control efficacy similar to that achieved through the use of an N95 respirator worn by the source and decreased airflow resistance using nanofiber masks may improve compliance and reduce receiver exposure. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Discrimination Training and Formative Evaluation for Remediation in Basic Waxing Skills.

ERIC Educational Resources Information Center

Knight, G. William; Guenzel, Pamela

1990-01-01

An experimental group (n=6) of student dentists received discrimination training and self-evaluation exercises on 4 waxing projects and 4 handpiece projects over 13 hours. An equivalent "conventional" group (n=7) received verbal feedback with models on 7 waxing projects over 13 hours. The experimental group outperformed the conventional…

Improved PLL For FM Demodulator

NASA Technical Reports Server (NTRS)

Kirkham, Harold; Jackson, Shannon P.

1992-01-01

Phase-locked loop (PLL) for frequency demodulator contains improved frequency-to-voltage converter producing less ripple than conventional phase detector. In improved PLL, phase detector replaced by state estimator, implemented by ramp/sample-and-hold circuit. Intended to reduce noise in receiver of frequency-modulated (FM) telemetry link without sacrificing bandwidth. Also applicable to processing received FM signals.

The Impact of Recurrent On-Line Synchronous Scientific Argumentation on Students' Argumentation and Conceptual Change

ERIC Educational Resources Information Center

Chen, Chien-Hsien; She, Hsiao-Ching

2012-01-01

This study reports the impact of Recurrent On-Line Synchronous Scientific Argumentation learning on 8th grade students' scientific argumentation ability and conceptual change involving physical science. The control group (N = 76) were recruited to receive conventional instruction whereas the experimental group (N = 74) received the Recurrent…

26 CFR 514.3 - Dividends received by addressee not actual owner.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) REGULATIONS UNDER TAX CONVENTIONS FRANCE Withholding of Tax § 514.3 Dividends received by... in France of any dividend, paid on or after January 1, 1957, from which United States tax at the... source. (2) Fiduciary or partnership. A fiduciary or a partnership with an address in France which...

Low-level laser therapy of myofascial pain syndromes of patients with osteoarthritis of knee and hip joints

NASA Astrophysics Data System (ADS)

Gasparyan, Levon V.

2001-04-01

The purpose of the given research is the comparison of efficiency of conventional treatment of myofascial pain syndromes of patients with osteoarthritis (OA) of hip and knee joints and therapy with additional application of low level laser therapy (LLLT) under dynamic control of clinical picture, rheovasographic, electromyographic examinations, and parameters of peroxide lipid oxidation. The investigation was made on 143 patients with OA of hip and knee joints. Patients were randomized in 2 groups: basic group included 91 patients, receiving conventional therapy with a course of LLLT, control group included 52 patients, receiving conventional treatment only. Transcutaneous ((lambda) equals 890 nm, output peak power 5 W, frequency 80 - 3000 Hz) and intravenous ((lambda) equals 633 nm, output 2 mW in the vein) laser irradiation were used for LLLT. Studied showed, that clinical efficiency of LLLT in the complex with conventional treatment of myofascial pain syndromes at the patients with OA is connected with attenuation of pain syndrome, normalization of parameters of myofascial syndrome, normalization of the vascular tension and parameters of rheographic curves, as well as with activation of antioxidant protection system.

Application of Renyi entropy for ultrasonic molecular imaging

PubMed Central

Hughes, M. S.; Marsh, J. N.; Arbeit, J. M.; Neumann, R. G.; Fuhrhop, R. W.; Wallace, K. D.; Thomas, L.; Smith, J.; Agyem, K.; Lanza, G. M.; Wickline, S. A.; McCarthy, J. E.

2009-01-01

Previous work has demonstrated that a signal receiver based on a limiting form of the Shannon entropy is, in certain settings, more sensitive to subtle changes in scattering architecture than conventional energy-based signal receivers [M. S. Hughes et al., J. Acoust. Soc. Am. 121, 3542–3557 (2007)]. In this paper new results are presented demonstrating further improvements in sensitivity using a signal receiver based on the Renyi entropy. PMID:19425656

An experimental measurement of galactic cosmic radiation dose in conventional aircraft between San Francisco and London compared to theoretical values for conventional and supersonic aircraft

NASA Technical Reports Server (NTRS)

Wallace, R.; Boyer, M. F.

1972-01-01

These direct measurements are in fair agreement with computations made using a program which considers both basic cosmic ray atmospheric physics and the focusing effect of the earth's magnetic field. These measurements also agree with those made at supersonic jet aircraft altitudes in Rb-57 aircraft. It is concluded that experiments and theory show that the doses received at conventional jet aircraft altitudes are slightly higher than those encountered in supersonic flights at much higher altitudes.

In vitro evaluation of an alternative method to bond molar tubes

PubMed Central

PINZAN-VERCELINO, Célia Regina Maio; PINZAN, Arnaldo; GURGEL, Júlio de Araújo; BRAMANTE, Fausto Silva; PINZAN, Luciana Maio

2011-01-01

Despite the advances in bonding materials, many clinicians today still prefer to place bands on molar teeth. Molar bonding procedures need improvement to be widely accepted clinically. Objective The purpose of this study was to evaluate the shear bond strength when an additional adhesive layer was applied on the occlusal tooth/tube interface to provide reinforcement to molar tubes. Material and methods Sixty third molars were selected and allocated to the 3 groups: group 1 received a conventional direct bond followed by the application of an additional layer of adhesive on the occlusal tooth/tube interface, group 2 received a conventional direct bond, and group 3 received a conventional direct bond and an additional cure time of 10 s. The specimens were debonded in a universal testing machine. The results were analyzed statistically by ANOVA and Tukey’s test (α=0.05). Results Group 1 had a significantly higher (p<0.05) shear bond strength compared to groups 2 and 3. No difference was detected between groups 2 and 3 (p>0.05). Conclusions The present in vitro findings indicate that the application of an additional layer of adhesive on the tooth/tube interface increased the shear bond strength of the bonded molar tubes. PMID:21437468

A non-randomised, controlled clinical trial of an innovative device for negative pressure wound therapy of pressure ulcers in traumatic paraplegia patients.

PubMed

Srivastava, Rajeshwar N; Dwivedi, Mukesh K; Bhagat, Amit K; Raj, Saloni; Agarwal, Rajiv; Chandra, Abhijit

2016-06-01

The conventional methods of treatment of pressure ulcers (PUs) by serial debridement and daily dressings require prolonged hospitalisation, associated with considerable morbidity. There is, however, recent evidence to suggest that negative pressure wound therapy (NPWT) accelerates healing. The commercial devices for NPWT are costly, cumbersome, and electricity dependent. We compared PU wound healing in traumatic paraplegia patients by conventional dressing and by an innovative negative pressure device (NPD). In this prospective, non-randomised trial, 48 traumatic paraplegia patients with PUs of stages 3 and 4 were recruited. Patients were divided into two groups: group A (n = 24) received NPWT with our NPD, and group B (n = 24) received conventional methods of dressing. All patients were followed up for 9 weeks. At week 9, all patients on NPD showed a statistically significant improvement in PU healing in terms of slough clearance, granulation tissue formation, wound discharge and culture. A significant reduction in wound size and ulcer depth was observed in NPD as compared with conventional methods at all follow-up time points (P = 0·0001). NPWT by the innovative device heals PUs at a significantly higher rate than conventional treatment. The device is safe, easy to apply and cost-effective. © 2014 The Authors. International Wound Journal © 2014 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

Tongue acupuncture in treatment of post-stroke dysphagia

PubMed Central

Cai, Haiyan; Ma, Benxu; Gao, Xia; Gao, Huanmin

2015-01-01

Tongue acupuncture is a technique that treats illness through acupuncture applied to the tongue. This study was designed to assess its therapeutic effects in the treatment of post-stroke dysphagia. A clinical control study was conducted with randomly selected 180 patients with post-stroke dysphagia. The patients were assigned into 2 groups: 90 in the Tongue acupuncture group received tongue acupuncture on the basis of conventional medication, 90 in the conventional acupuncture group received acupuncture on the neck and wrist. Acupoints in the tongue are Juanquan (EX-HN10) (at the midpoint of dorsal raphe of the tongue) and Haiquan (EX-HN11) (Sublingual frenulum midpoint). Acupoits on the body are Fengchi (GB20) and Neiguan (PC6). The effective rate, the national institutes of health stroke scale (NIHSS), TV X-ray fluoroscopy swallowing function (VFSS), the incidence rate of pneumonia were used to evaluate the efficacy after 4 weeks treatment. The NIHSS and VFSS of tongue acupuncture group were improved significantly than that of the conventional group (P < 0.01, respectively). The incidence rate of pneumonia decreased (P < 0. 01). The effective rate of the tongue acupuncture group was higher than that of conventional group (96.67% vs. 66.67%, P < 0. 01). On the basis of the conventional medication, tongue acupuncture would effectively improve the swallow functions, decrease the neurological deficit and reduce the incidence of pneumonia in patients with post-stroke dysphagia. PMID:26550374

Incidence of tardive dyskinesia with atypical versus conventional antipsychotic medications: a prospective cohort study.

PubMed

Woods, Scott W; Morgenstern, Hal; Saksa, John R; Walsh, Barbara C; Sullivan, Michelle C; Money, Roy; Hawkins, Keith A; Gueorguieva, Ralitza V; Glazer, William M

2010-04-01

Most previous studies of the incidence of tardive dyskinesia with atypical antipsychotics compared with conventional antipsychotics have not had tardive dyskinesia as their primary focus. The current study aimed to compare the incidence of tardive dyskinesia with atypical vs conventional antipsychotics using methods similar to those from a previous prospective cohort study at our site in the 1980s. Three hundred fifty-two initially tardive dyskinesia-free psychiatric outpatients (diagnosed at baseline using the Structured Clinical Interview for DSM-IV) were examined for a new diagnosis of tardive dyskinesia (using the Abnormal Involuntary Movement Scale and Glazer-Morgenstern criteria) every 6 months for up to 4 years at a community mental health center. At baseline, subjects were receiving conventional antipsychotics only (23%), atypicals only (64%), or both (14%). Only 26 subjects had never received conventional antipsychotics. Baseline evaluations were conducted from November 2000 through May 2003. Follow-ups were conducted through February 2005. Compared with subjects treated with conventional antipsychotics alone since the previous visit, the adjusted tardive dyskinesia incidence rate-ratio for subjects treated with atypical antipsychotics alone was 0.68 (95% CI, 0.29-1.64). The incidence and prevalence of tardive dyskinesia was similar to previous findings at this site in the 1980s. The incidence of tardive dyskinesia with recent exposure to atypical antipsychotics alone was more similar to that for conventional antipsychotics than in most previous studies. Despite high penetration of atypical antipsychotics into clinical practice, the incidence and prevalence of tardive dyskinesia appeared relatively unchanged since the 1980s. Clinicians should continue to monitor for tardive dyskinesia, and researchers should continue to pursue efforts to treat or prevent it. Copyright 2010 Physicians Postgraduate Press, Inc.

Aerodynamic Performance of a Compact, High Work-Factor Centrifugal Compressor at the Stage and Subcomponent Level

NASA Technical Reports Server (NTRS)

Braunscheidel, Edward P.; Welch, Gerard E.; Skoch, Gary J.; Medic, Gorazd; Sharma, Om P.

2014-01-01

The measured aerodynamic performance of a compact, high work factor, single-stage centrifugal compressor, comprising an impeller, diffuser, 90-bend, and exit guide vane (EGV), is reported. Performance levels are based on steady-state total-pressure and total-temperature rake and angularity-probe data acquired at key machine rating planes during recent testing at NASA Glenn Research Center. Aerodynamic performance at the stage level are reported for operation between 70 to 105 of design corrected speed, with subcomponent (impeller, diffuser, and exitguide-vane) detailed flow field measurements presented and discussed at the 100 design-speed condition. Individual component losses from measurements are compared with pre-test predictions on a limited basis.

High temperature helical tubular receiver for concentrating solar power system

NASA Astrophysics Data System (ADS)

Hossain, Nazmul

In the field of conventional cleaner power generation technology, concentrating solar power systems have introduced remarkable opportunity. In a solar power tower, solar energy concentrated by the heliostats at a single point produces very high temperature. Falling solid particles or heat transfer fluid passing through that high temperature region absorbs heat to generate electricity. Increasing the residence time will result in more heat gain and increase efficiency. A novel design of solar receiver for both fluid and solid particle is approached in this paper which can increase residence time resulting in higher temperature gain in one cycle compared to conventional receivers. The helical tubular solar receiver placed at the focused sunlight region meets the higher outlet temperature and efficiency. A vertical tubular receiver is modeled and analyzed for single phase flow with molten salt as heat transfer fluid and alloy625 as heat transfer material. The result is compared to a journal paper of similar numerical and experimental setup for validating our modeling. New types of helical tubular solar receivers are modeled and analyzed with heat transfer fluid turbulent flow in single phase, and granular particle and air plug flow in multiphase to observe the temperature rise in one cyclic operation. The Discrete Ordinate radiation model is used for numerical analysis with simulation software Ansys Fluent 15.0. The Eulerian granular multiphase model is used for multiphase flow. Applying the same modeling parameters and boundary conditions, the results of vertical and helical receivers are compared. With a helical receiver, higher temperature gain of heat transfer fluid is achieved in one cycle for both single phase and multiphase flow compared to the vertical receiver. Performance is also observed by varying dimension of helical receiver.

How to Study Chronic Diseases-Implications of the Convention on the Rights of Persons with Disabilities for Research Designs.

PubMed

von Peter, Sebastian; Bieler, Patrick

2017-01-01

The Convention on the Rights of Persons with Disabilities (CRPD) has been received considerable attention internationally. The Convention's main arguments are conceptually analyzed. Implications for the development of research designs are elaborated upon. The Convention entails both a human rights and a sociopolitical dimension. Advancing a relational notion of disability, it enters a rather foreign terrain to medical sciences. Research designs have to be changed accordingly. Research designs in accordance with the CRPD should employ and further develop context-sensitive research strategies and interdisciplinary collaboration. Complex designs that allow for a relational analysis of personalized effects have to be established and evaluated, thereby systematically integrating qualitative methods.

Low-cost high-resolution fast spin-echo MR of acoustic schwannoma: an alternative to enhanced conventional spin-echo MR?

PubMed

Allen, R W; Harnsberger, H R; Shelton, C; King, B; Bell, D A; Miller, R; Parkin, J L; Apfelbaum, R I; Parker, D

1996-08-01

To determine whether unenhanced high-resolution T2-weighted fast spin-echo MR imaging provides an acceptable and less expensive alternative to contrast-enhanced conventional T1-weighted spin-echo MR techniques in the diagnosis of acoustic schwannoma. We reviewed in a blinded fashion the records of 25 patients with pathologically documented acoustic schwannoma and of 25 control subjects, all of whom had undergone both enhanced conventional spin-echo MR imaging and unenhanced fast spin-echo MR imaging of the cerebellopontine angle/internal auditory canal region. The patients were imaged with the use of a quadrature head receiver coil for the conventional spin-echo sequences and dual 3-inch phased-array receiver coils for the fast spin-echo sequences. The size of the acoustic schwannomas ranged from 2 to 40 mm in maximum dimension. The mean maximum diameter was 12 mm, and 12 neoplasms were less than 10 mm in diameter. Acoustic schwannoma was correctly diagnosed on 98% of the fast spin-echo images and on 100% of the enhanced conventional spin-echo images. Statistical analysis of the data using the kappa coefficient demonstrated agreement beyond chance between these two imaging techniques for the diagnosis of acoustic schwannoma. There is no statistically significant difference in the sensitivity and specificity of unenhanced high-resolution fast spin-echo imaging and enhance T1-weighted conventional spin-echo imaging in the detection of acoustic schwannoma. We believe that the unenhanced high-resolution fast spin-echo technique provides a cost-effective method for the diagnosis of acoustic schwannoma.

78 FR 3081 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-15

... receiver, electrical key and an electronic control module (ECM). The conventional key components consist of a transponder key ECU assembly, transponder key coil, security indicator, ignition key and an ECM... certification ECU and steering lock ECU receive confirmation of the valid key, allowing the ECM to start the...

76 FR 59173 - Standard Format and Content of License Applications for Conventional Uranium Mills

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-23

...On May 30, 2008 (73 FR 31152), the U.S. Nuclear Regulatory Commission (NRC) published for public comment a notice of issuance and availability of Draft Regulatory Guide (DG)-3024, ``Standard Format and Content of License Applications for Conventional Uranium Mills.'' DG- 3024 was a proposed Revision 2 of Regulatory Guide (RG) 3.5. However, upon further consideration the NRC has decided not to revise RG 3.5 at this time. For this reason, DG-3024 will be withdrawn. The comment period closed on August 4, 2008, and 6 comments were received. The comments received will be considered and incorporated as appropriate if the NRC decides to revise RG 3.5 in the future.

SweepSAR: Beam-forming on Receive Using a Reflector-Phased Array Feed Combination for Spaceborne SAR

NASA Technical Reports Server (NTRS)

Freeman, A.; Krieger, G.; Rosen, P.; Younis, M.; Johnson, W. T. K.; Huber, S.; Jordan, R.; Moreira, A.

2012-01-01

In this paper, an alternative approach is described that is suited for longer wavelength SARs in particular, employing a large, deployable reflector antenna and a much simpler phased array feed. To illuminate a wide swath, a substantial fraction of the phased array feed is excited on transmit to sub-illuminate the reflector. Shorter transmit pulses are required than for conventional SAR. On receive, a much smaller portion of the phased array feed is used to collect the return echo, so that a greater portion of the reflector antenna area is used. The locus of the portion of the phased array used on receive is adjusted using an analog beam steering network, to 'sweep' the receive beam(s) across the illuminated swath, tracking the return echo. This is similar in some respects to the whiskbroom approach to optical sensors, hence the name: SweepSAR.SweepSAR has advantages over conventional SAR in that it requires less transmit power, and if the receive beam is narrow enough, it is relatively immune to range ambiguities. Compared to direct radiating arrays with digital beam- forming, it is much simpler to implement, uses currently available technologies, is better suited for longer wavelength systems, and does not require extremely high data rates or onboard processing.

A comparative study of optical concentrators for visible light communications

NASA Astrophysics Data System (ADS)

Mulyawan, Rahmat; Gomez, Ariel; Chun, Hyunchae; Rajbhandari, Sujan; Manousiadis, Pavlos P.; Vithanage, Dimali A.; Faulkner, Grahame; Turnbull, Graham A.; Samuel, Ifor D. W.; Collins, Stephen; O'Brien, Dominic

2017-01-01

Given the imminent radio frequency spectrum crunch, Visible Light Communication (VLC) is being proposed as an alternative wireless technology allowing for scalable connectivity to potentially millions of mobile and Internet-of- Things (IoT) devices. A VLC system uses a photo-detector (PD) receiver that converts the optically modulated light from a light source into a modulated electrical signal. The corresponding receiver electrical bandwidth is typically inversely proportional to the PD active area. Consequently, to construct a high-speed VLC link, the PD active area is often substantially reduced and an optical concentrator is used to enhance the receiver collection area. However, to achieve high concentrating factor, the link field-of-view (FOV) needs to be narrow due to the étendue conservation in linear passive optical systems. This paper studies a Fluorescent Concentrator (FC) that breaks this étendue conservation. The FC is not only based on reflective and refractive principles but also makes use of fluorescence process. A comparison between the FC and conventional optical concentrators, namely Compound Parabolic Concentrator (CPC) is also investigated. The trade-off between received signal strength and incoming link angle is demonstrated over 60° coverage. Experimental results show that performance degradation as the link angle increases using FC-based receivers is significantly lower than for conventional CPC.

Effect of Video Triggering During Conventional Lectures on Final Grades of Dental Students in an Oral Biology Course: A Two-Year Retrospective Study.

PubMed

Farooq, Imran; Al-Jandan, Badr A

2015-12-01

The aim of this study was to analyze the effect of the inclusion of video triggers in conventional face-to-face lectures on the final grades of dental students in an oral biology course. The study consisted of two groups of students taking the course in two academic years at a dental school in Saudi Arabia: group 1, 2013-14 (control); and group 2, 2014-15. The total sample comprised 163 students (n=163; group 1: 71 and group 2: 92). Group 1 received lectures without any videos, whereas group 2 received lectures that included two to three videos of one to five minutes in duration with triggering effect (a video was shown every 10-15 minutes into the lecture). The final examination grades of the students were accessed retrospectively, and the data were compared with a chi-square test. The results confirmed that a higher number of students who received video triggering during lectures (group 2) performed better than their counterparts who did not receive video triggers (group 1); the difference was statistically significant (p<0.05). Among the group 2 students, 26% achieved a grade of A, and 37% achieved a grade of B. In contrast, only 7% of the group 1 students obtained a grade of A, and 31% achieved a grade of B. These results suggest that video triggers may offer an advantage over conventional methods and their inclusion in lectures can be a way to enhance students' learning.

Significance of stress transfer in time-dependent earthquake probability calculations

USGS Publications Warehouse

Parsons, T.

2005-01-01

A sudden change in stress is seen to modify earthquake rates, but should it also revise earthquake probability? Data used to derive input parameters permits an array of forecasts; so how large a static stress change is require to cause a statistically significant earthquake probability change? To answer that question, effects of parameter and philosophical choices are examined through all phases of sample calculations, Drawing at random from distributions of recurrence-aperiodicity pairs identifies many that recreate long paleoseismic and historic earthquake catalogs. Probability density funtions built from the recurrence-aperiodicity pairs give the range of possible earthquake forecasts under a point process renewal model. Consequences of choices made in stress transfer calculations, such as different slip models, fault rake, dip, and friction are, tracked. For interactions among large faults, calculated peak stress changes may be localized, with most of the receiving fault area changed less than the mean. Thus, to avoid overstating probability change on segments, stress change values should be drawn from a distribution reflecting the spatial pattern rather than using the segment mean. Disparity resulting from interaction probability methodology is also examined. For a fault with a well-understood earthquake history, a minimum stress change to stressing rate ratio of 10:1 to 20:1 is required to significantly skew probabilities with >80-85% confidence. That ratio must be closer to 50:1 to exceed 90-95% confidence levels. Thus revision to earthquake probability is achievable when a perturbing event is very close to the fault in question or the tectonic stressing rate is low.

Growth, Morphogenesis, and Virulence of Candida albicans after Oral Inoculation in the Germ-Free and Conventional Chick1

PubMed Central

Balish, Edward; Phillips, A. W.

1966-01-01

Balish, Edward (Syracuse University, Syracuse, N.Y.), and A. W. Phillips. Growth, morphogenesis, and virulence of Candida albicans after oral inoculation in the germ-free and conventional chick. J. Bacteriol. 91:1736–1743. 1966.—The effects of intestinal bacteria on the multiplication, morphogenesis, and infectivity of Candida albicans in the alimentary tract were investigated by comparing results obtained in germ-free and conventional chicks after oral inoculation. This challenge resulted in the establishment of large numbers of the pathogen in the alimentary tract of each group of chicks; these numbers were increased in crop contents from challenged bacteria-free chicks wherein hyphae predominated over the yeast form. These animals also had lesions of the crop epithelium containing numerous hyphae and few yeast-like forms. In contrast, challenged conventional chicks receiving an adequate diet displayed no evidence of infection. Their alimentary tract contained the yeast form of C. albicans; no hyphae were seen. Although we found bacterial inhibition of C. albicans multiplication in the alimentary tract, this in itself did not seem to explain the resistance to intestinal candidiasis in our conventional chicks. We argued that this resistance to infection was due chiefly to the prevention of hyphal development in C. albicans by intestinal bacteria. C. albicans in the gut of our conventional chicks resulted in some increase in numbers of enterococci in contents from the crop. Increased pH values in contents from the gut of germ-free chicks were not clearly related to infection after challenge. The Eh of the above crop contents were only slightly decreased in the germ-free crop. Thus the Eh did not appear to be involved in susceptibility to infection. Invasion of the blood stream and kidneys of conventional chicks by the yeast form of C. albicans occurred in challenged animals receiving a purified diet which had been radiation-sterilized and stored for 6 months at room temperature (25 C). Their growth rate decreased and they became moribund; no hyphae were observed in tissues or intestine of these animals. Challenged bacteria-free chicks receiving the same diet were resistant to the above invasion, although they had crop lesions containing hyphae as described. The resistance of these chicks to systemic invasion was attributed to absence of intestinal bacteria competing for low levels of vitamins in the stored diet. Germ-free chicks had decreased levels of serum γ-globulin which increased after challenge, whereas this value was unchanged in conventional birds after challenge. Images PMID:4160824

Effect of using reporting guidelines during peer review on quality of final manuscripts submitted to a biomedical journal: masked randomised trial

PubMed Central

Cortés, J; Ribera, J M; Cardellach, F; Selva-O’Callaghan, A; Kostov, B; García, L; Cirugeda, L; Altman, D G; González, J A; Sànchez, J A; Miras, F; Urrutia, A; Fonollosa, V; Rey-Joly, C; Vilardell, M

2011-01-01

Objective To investigate the effect of an additional review based on reporting guidelines such as STROBE and CONSORT on quality of manuscripts. Design Masked randomised trial. Population Original research manuscripts submitted to the Medicina Clínica journal from May 2008 to April 2009 and considered suitable for publication. Intervention Control group: conventional peer reviews alone. Intervention group: conventional review plus an additional review looking for missing items from reporting guidelines. Outcomes Manuscript quality, assessed with a 5 point Likert scale (primary: overall quality; secondary: average quality of specific items in paper). Main analysis compared groups as allocated, after adjustment for baseline factors (analysis of covariance); sensitivity analysis compared groups as reviewed. Adherence to reviewer suggestions assessed with Likert scale. Results Of 126 consecutive papers receiving conventional review, 34 were not suitable for publication. The remaining 92 papers were allocated to receive conventional reviews alone (n=41) or additional reviews (n=51). Four papers assigned to the conventional review group deviated from protocol; they received an additional review based on reporting guidelines. We saw an improvement in manuscript quality in favour of the additional review group (comparison as allocated, 0.25, 95% confidence interval –0.05 to 0.54; as reviewed, 0.33, 0.03 to 0.63). More papers with additional reviews than with conventional reviews alone improved from baseline (22 (43%) v eight (20%), difference 23.6% (3.2% to 44.0%), number needed to treat 4.2 (from 2.3 to 31.2), relative risk 2.21 (1.10 to 4.44)). Authors in the additional review group adhered more to suggestions from conventional reviews than to those from additional reviews (average increase 0.43 Likert points (0.19 to 0.67)). Conclusions Additional reviews based on reporting guidelines improve manuscript quality, although the observed effect was smaller than hypothesised and not definitively demonstrated. Authors adhere more to suggestions from conventional reviews than to those from additional reviews, showing difficulties in adhering to high methodological standards at the latest research phases. To boost paper quality and impact, authors should be aware of future requirements of reporting guidelines at the very beginning of their study. Trial registration and protocol Although registries do not include trials of peer review, the protocol design was submitted to sponsored research projects (Instituto de Salud Carlos III, PI081903). PMID:22108262

Effects of High-Definition and Conventional tDCS on Response Inhibition.

PubMed

Hogeveen, J; Grafman, J; Aboseria, M; David, A; Bikson, M; Hauner, K K

2016-01-01

Response inhibition is a critical executive function, enabling the adaptive control of behavior in a changing environment. The inferior frontal cortex (IFC) is considered to be critical for response inhibition, leading researchers to develop transcranial direct current stimulation (tDCS) montages attempting to target the IFC and improve inhibitory performance. However, conventional tDCS montages produce diffuse current through the brain, making it difficult to establish causality between stimulation of any one given brain region and resulting behavioral changes. Recently, high-definition tDCS (HD-tDCS) methods have been developed to target brain regions with increased focality relative to conventional tDCS. Remarkably few studies have utilized HD-tDCS to improve cognitive task performance, however, and no study has directly compared the behavioral effects of HD-tDCS to conventional tDCS. In the present study, participants received either HD-tDCS or conventional tDCS to the IFC during performance of a response inhibition task (stop-signal task, SST) or a control task (choice reaction time task, CRT). A third group of participants completed the same behavioral protocols, but received tDCS to a control site (mid-occipital cortex). Post-stimulation improvement in SST performance was analyzed as a function of tDCS group and the task performed during stimulation using both conventional and Bayesian parameter estimation analyses. Bayesian estimation of the effects of HD- and conventional tDCS to IFC relative to control site stimulation demonstrated enhanced response inhibition for both conditions. No improvements were found after control task (CRT) training in any tDCS condition. Results support the use of both HD- and conventional tDCS to the IFC for improving response inhibition, providing empirical evidence that HD-tDCS can be used to facilitate performance on an executive function task. Copyright © 2016 Elsevier Inc. All rights reserved.

Peer coaching to teach faculty surgeons an advanced laparoscopic skill: A randomized controlled trial.

PubMed

Palter, Vanessa N; Beyfuss, Kaitlyn A; Jokhio, Adam R; Ryzynski, Agnes; Ashamalla, Shady

2016-11-01

Preliminary evidence suggests that coaching is an effective adjunct in resident training. The learning needs of faculty, however, are different from those of trainees. Assessing the effectiveness of peer coaching at improving the technical proficiency of practicing surgeons is an area that remains largely unexplored. The purpose of this study was to assess the efficacy of a peer coaching program that teaches laparoscopic suturing to faculty surgeons. Surgeons inexperienced in laparoscopic suturing were randomized to either conventional training or peer coaching. Both groups performed a pretest on a box trainer. The conventional training group then received a web link to a tutorial for teaching laparoscopic suturing and a box trainer for independent practice. In addition to the web link and the box trainer, the peer coaching group received 2 half hour peer coaching sessions. Both groups then performed a stitch on the box trainer that was video recorded. The primary outcome measure was technical performance, which was assessed by a global rating scale. Eighteen faculty were randomized (conventional training n = 9; peer coaching n = 9). Initially, there was no difference in technical skills between the groups (conventional training median score 10 [interquartile range 8.5-15]; peer coaching 13 [10.5-14]; P = .64). After the intervention, the peer coaching group had improved technical performance (conventional training 11 [8.5-12.5]; peer coaching 18 [17-19]; P < .01). Comparing the pre- and postintervention scores within both groups, there was an improvement in technical proficiency in the peer coaching group, yet none in the conventional training group (before conventional training 10 [8.5-15], after conventional training 11 [8.5-12.5]; P = .56; before peer coaching 13 [10.5-14], after peer coaching 18 [17-19]; P < .01). This trial demonstrates that a structured peer coaching program can facilitate faculty surgeons learning a novel procedure. Copyright © 2016 Elsevier Inc. All rights reserved.

Reliability-Based Design Optimization of a Composite Airframe Component

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Coroneos, Rula M.

2009-01-01

A stochastic design optimization methodology (SDO) has been developed to design components of an airframe structure that can be made of metallic and composite materials. The design is obtained as a function of the risk level, or reliability, p. The design method treats uncertainties in load, strength, and material properties as distribution functions, which are defined with mean values and standard deviations. A design constraint or a failure mode is specified as a function of reliability p. Solution to stochastic optimization yields the weight of a structure as a function of reliability p. Optimum weight versus reliability p traced out an inverted-S-shaped graph. The center of the inverted-S graph corresponded to 50 percent (p = 0.5) probability of success. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure that corresponds to unity for reliability p (or p = 1). Weight can be reduced to a small value for the most failure-prone design with a reliability that approaches zero (p = 0). Reliability can be changed for different components of an airframe structure. For example, the landing gear can be designed for a very high reliability, whereas it can be reduced to a small extent for a raked wingtip. The SDO capability is obtained by combining three codes: (1) The MSC/Nastran code was the deterministic analysis tool, (2) The fast probabilistic integrator, or the FPI module of the NESSUS software, was the probabilistic calculator, and (3) NASA Glenn Research Center s optimization testbed CometBoards became the optimizer. The SDO capability requires a finite element structural model, a material model, a load model, and a design model. The stochastic optimization concept is illustrated considering an academic example and a real-life raked wingtip structure of the Boeing 767-400 extended range airliner made of metallic and composite materials.

The Ms4.4 2016 Yuncheng, Shanxi, China, Seismic Sequence: Source Characterizations and Tectonic Implications

NASA Astrophysics Data System (ADS)

Xie, Z.; Riaz, M. S.; Zheng, Y.; Xiong, X.

2017-12-01

On 12 March 2016 at 11:14 (Beijing time) , a moderate earthquake with magnitude Ms4.4 struck Yuncheng County, Shanxi Province, Central China. Seismic activity continued with numerous aftershocks, and another event with little smaller magnitude of Ms4.0 occurred on 27 March 2016 at 3:58 as well as a lot of aftershocks followed. Seismic waves from the earthquakes were recorded by a dense local broadband seismic network in Shanxi and its surrounding provinces, enabling detailed the source characterizations of this earthquake sequence. The hypocenters of the Yuncheng earthquake sequence determined by the TomoDD method displayed that the events occurred in the middle of Yuncheng Basin which locates between Weihe Basin and Fenhe Basin, one of renowned active seismic belts in mainland China. The relocation of the aftershocks presented a NNW-SSE orientated distribution, and the earlier aftershocks tended to fault at shallow depths, concentrating at 5 km. After the Ms4.0 event, the aftershocks extended to the SSE direction with deeper focal depths. The focal mechanisms of the mainshock and the biggest aftershock obtained by the CAP (Cut And Paste) method indicated consistent right-lateral strike-slip faults. Since the magnitude was relatively small, no surface rupture associated with this shock sequence had been observed, and no known faults exited around the epicenter, indicating that the causative fault was ambiguous just based on the focal mechanism. According to the aftershocks distribution and the recent GPS results, the ruptured fault was apt to the nodal plane striking at 194°, dipping 79° and rake 151° for Ms4.4 mainshock and 199°/73°/141°, representing strike/dip/rake, for Ms4.0 aftershock. This earthquake sequence was regarded as an adjustment of stress accumulation in the pull-apart Yuncheng Basin, implying that the energy around the boundary faults of the basin has accumulated continuously.

Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation

PubMed Central

Gharwade, Chandrakant Rambhau

2016-01-01

Follicular unit extraction (FUE) is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant). Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs). The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°–15°) of emergent hair from scalp skin, higher variance angle (15°–35°) between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions. PMID:28216821

Flight Test Results from the Rake Airflow Gage Experiment on the F-15B

NASA Technical Reports Server (NTRS)

Frederick, Michael; Ratnayake, Nalin

2011-01-01

The results are described of the Rake Airflow Gage Experiment (RAGE), which was designed and fabricated to support the flight test of a new supersonic inlet design using Dryden's Propulsion Flight Test Fixture (PFTF) and F-15B testbed airplane (see figure). The PFTF is a unique pylon that was developed for flight-testing propulsion-related experiments such as inlets, nozzles, and combustors over a range of subsonic and supersonic flight conditions. The objective of the RAGE program was to quantify the local flowfield at the aerodynamic interface plane of the Channeled Centerbody Inlet Experiment (CCIE). The CCIE is a fixed representation of a conceptual mixed-compression supersonic inlet with a translating biconic centerbody. The primary goal of RAGE was to identify the relationship between free-stream and local Mach number in the low supersonic regime, with emphasis on the identification of the particular free-stream Mach number that produced a local Mach number of 1.5. Measurements of the local flow angularity, total pressure distortion, and dynamic pressure over the interface plane were also desired. The experimental data for the RAGE program were obtained during two separate research flights. During both flights, local flowfield data were obtained during straight and level acceleration segments out to steady-state test points. The data obtained from the two flights showed small variations in Mach number, flow angularity, and dynamic pressure across the interface plane at all flight conditions. The data show that a free-stream Mach number of 1.65 will produce the desired local Mach number of 1.5 for CCIE. The local total pressure distortion over the interface plane at this condition was approximately 1.5%. At this condition, there was an average of nearly 2 of downwash over the interface plane. This small amount of downwash is not expected to adversely affect the performance of the CCIE inlet.

A formulation of directivity for earthquake sources using isochrone theory

USGS Publications Warehouse

Spudich, Paul; Chiou, Brian S.J.; Graves, Robert; Collins, Nancy; Somerville, Paul

2004-01-01

A functional form for directivity effects can be derived from isochrone theory, in which the measure of the directivity-induced amplification of an S body wave is c, the isochrone velocity. Ground displacement of the near-, intermediate-, and far-field terms of P and S waves is linear in isochrone velocity for a finite source in a whole space. We have developed an approximation c-tilde-prime of isochrone velocity that can easily be implemented as a predictor of directivity effects in empirical ground motion prediction relations. Typically, for a given fault surface, hypocenter, and site geometry, c-tilde-prime is a simple function of the hypocentral distance, the rupture distance, the crustal shear wave speed in the seismogenic zone, and the rupture velocity. c-tilde-prime typically ranges in the interval 0.44, for rupture away from the station, to about 4, for rupture toward the station. In this version of the theory directivity is independent of period. Additionally, we have created another functional form which is c-tilde-prime modified to include the approximate radiation pattern of a finite fault having a given rake. This functional form can be used to model the spatial variations of fault-parallel and fault-normal horizontal ground motions. The strengths of this formulation are 1) the proposed functional form is based on theory, 2) the predictor is unambiguously defined for all possible site locations and source rakes, and 3) it can easily be implemented for well-studied important previous earthquakes. We compare predictions of our functional form with synthetic ground motions calculated for finite strike-slip and dip-slip faults in the magnitude range 6.5 - 7.5. In general our functional form correlates best with computed fault-normal and fault-parallel motions in the synthetic motions calculated for events with M6.5. Correlation degrades but is still useful for larger events and for the geometric average horizontal motions. We have had limited success applying it to geometrically complicated faults.

Use of fault striations and dislocation models to infer tectonic shear stress during the 1995 Hyogo-Ken Nanbu (Kobe) earthquake

USGS Publications Warehouse

Spudich, P.; Guatteri, Mariagiovanna; Otsuki, K.; Minagawa, J.

1998-01-01

Dislocation models of the 1995 Hyogo-ken Nanbu (Kobe) earthquake derived by Yoshida et al. (1996) show substantial changes in direction of slip with time at specific points on the Nojima and Rokko fault systems, as do striations we observed on exposures of the Nojima fault surface on Awaji Island. Spudich (1992) showed that the initial stress, that is, the shear traction on the fault before the earthquake origin time, can be derived at points on the fault where the slip rake rotates with time if slip velocity and stress change are known at these points. From Yoshida's slip model, we calculated dynamic stress changes on the ruptured fault surfaces. To estimate errors, we compared the slip velocities and dynamic stress changes of several published models of the earthquake. The differences between these models had an exponential distribution, not gaussian. We developed a Bayesian method to estimate the probability density function (PDF) of initial stress from the striations and from Yoshida's slip model. Striations near Toshima and Hirabayashi give initial stresses of about 13 and 7 MPa, respectively. We obtained initial stresses of about 7 to 17 MPa at depths of 2 to 10 km on a subset of points on the Nojima and Rokko fault systems. Our initial stresses and coseismic stress changes agree well with postearthquake stresses measured by hydrofracturing in deep boreholes near Hirabayashi and Ogura on Awaji Island. Our results indicate that the Nojima fault slipped at very low shear stress, and fractional stress drop was complete near the surface and about 32% below depths of 2 km. Our results at depth depend on the accuracy of the rake rotations in Yoshida's model, which are probably correct on the Nojima fault but debatable on the Rokko fault. Our results imply that curved or cross-cutting fault striations can be formed in a single earthquake, contradicting a common assumption of structural geology.

Mind-Body Approaches to Treating Mental Health Symptoms Among Disadvantaged Populations: A Comprehensive Review.

PubMed

Burnett-Zeigler, Inger; Schuette, Stephanie; Victorson, David; Wisner, Katherine L

2016-02-01

Mind-body approaches are commonly used to treat a variety of chronic health conditions, including depression and anxiety. A substantial proportion of individuals with depression and anxiety disorders do not receive conventional treatment; disadvantaged individuals are especially unlikely to receive treatment. Mind-body approaches offer a potentially more accessible and acceptable alternative to conventional mental health treatment for disadvantaged individuals, who may not otherwise receive mental health treatment. This review examines evidence for the efficacy of mind-body interventions for mental health symptoms among disadvantaged populations. While rates of utilization were relatively lower for racial/ethnic minorities, evidence suggests that significant proportions of racial/ethnic minorities are using complementary health approaches as health treatments, especially prayer/healers and natural or herbal remedies. This review of studies on the efficacy of mind-body interventions among disadvantaged populations found evidence for the efficacy of mind-body approaches for several mental and physical health symptoms, functioning, self-care, and overall quality of life.

Optical and thermal performance of bladed receivers

NASA Astrophysics Data System (ADS)

Pye, John; Coventry, Joe; Ho, Clifford; Yellowhair, Julius; Nock, Ian; Wang, Ye; Abbasi, Ehsan; Christian, Joshua; Ortega, Jesus; Hughes, Graham

2017-06-01

Bladed receivers use conventional receiver tube-banks rearranged into bladed/finned structures, and offer better light trapping, reduced radiative and convective losses, and reduced tube mass, based on the presented optical and thermal analysis. Optimising for optical performance, deep blades emerge. Considering thermal losses leads to shallower blades. Horizontal blades perform better, in both windy and no-wind conditions, than vertical blades, at the scales considered so far. Air curtains offer options to further reduce convective losses; high flux on blade-tips is still a concern.

EEG Monitoring Technique Influences the Management of Hypoxic-Ischemic Seizures in Neonates Undergoing Therapeutic Hypothermia.

PubMed

Jan, Saber; Northington, Frances J; Parkinson, Charlamaine M; Stafstrom, Carl E

2017-01-01

Electroencephalogram (EEG) monitoring techniques for neonatal hypoxia-ischemia (HI) are evolving over time, and the specific type of EEG utilized could influence seizure diagnosis and management. We examined whether the type of EEG performed affected seizure treatment decisions (e.g., the choice and number of antiseizure drugs [ASDs]) in therapeutic hypothermia-treated neonates with HI from 2007 to 2015 in the Johns Hopkins Hospital Neonatal Intensive Care Unit. During this period, 3 different EEG monitoring protocols were utilized: Period 1 (2007-2009), single, brief conventional EEG (1 h duration) at a variable time during therapeutic hypothermia treatment, i.e., ordered when a seizure was suspected; Period 2 (2009-2013), single, brief conventional EEG followed by amplitude-integrated EEG for the duration of therapeutic hypothermia treatment and another brief conventional EEG after rewarming; and Period 3 (2014-2015), continuous video-EEG (cEEG) for the duration of therapeutic hypothermia treatment (72 h) plus for an additional 12 h during and after rewarming. One hundred and sixty-two newborns were included in this retrospective cohort study. As a function of the type and duration of EEG monitoring, we assessed the risk (likelihood) of receiving no ASD, at least 1 ASD, or ≥2 ASDs. We found that the risk of a neonate being prescribed an ASD was 46% less during Period 3 (cEEG) than during Period 1 (brief conventional EEG only) (95% CI 6-69%, p = 0.03). After adjusting for initial EEG and MRI results, compared with Period 1, there was a 38% lower risk of receiving an ASD during Period 2 (95% CI: 9-58%, p = 0.02) and a 67% lower risk during Period 3 (95% CI: 23-86%, p = 0.01). The risk ratio of receiving ≥2 ASDs was not significantly different across the 3 periods. In conclusion, in addition to the higher sensitivity and specificity of continuous video-EEG monitoring, fewer infants are prescribed an ASD when undergoing continuous forms of EEG monitoring (aEEG or cEEG) than those receiving conventional EEG. We recommend that use of continuous video-EEG be considered whenever possible, both to treat seizures more specifically and to avoid overtreatment. © 2017 S. Karger AG, Basel.

First and Second Language Acquisition in German Children Attending a Kindergarten Immersion Program: A Combined Longitudinal and Cross-Sectional Study

ERIC Educational Resources Information Center

Bergström, Kirstin; Klatte, Maria; Steinbrink, Claudia; Lachmann, Thomas

2016-01-01

This study investigated first (L1) and second (L2) language acquisition in two age-matched groups of 2- to 6-year-old kindergarten children over the course of 2.5 years. The immersion group participated in a partial English immersion program whereas the conventional instruction group received a conventional L2 course (30 minutes per week); the…

Efficacy and safety of add on low-dose mirtazapine in depression.

PubMed

Matreja, Prithpal S; Badyal, Dinesh K; Deswal, Randhir S; Sharma, Arvind

2012-03-01

Although antidepressant medications are effective, they have a delayed onset of effect. Mirtazapine, an atypical antidepressant is an important option for add-on therapy in major depression. There is insufficient data on mirtazapine in Indian population; hence this study was designed to study the add-on effect of low-dose mirtazapine with selective serotonin reuptake inhibitors (SSRIs) in major depressive disorder (MDD) in Indian population. In an open, randomized study, 60 patients were divided into two groups. In Group A (n=30) patients received conventional SSRIs for 6 weeks. In Group B (n=30) patients received conventional SSRIs with low-dose mirtazapine for 6 weeks. Patients were evaluated at baseline and then at 1, 2, 3, 4, 5, and 6 weeks. There was significant improvement in Hamilton Depression Rating Scale (HDRS), Montgomery and Asberg depression rating scale (MADRS) scores (P<0.05) in both groups. Mirtazapine in low dose as add on therapy showed improvement in scores, had earlier onset of action, and more number of responders and remitters as compared to conventional treatment (P<0.05). No serious adverse event was reported in either of the groups. Low-dose mirtazapine as add-on therapy has shown better efficacy, earlier onset of action and more number of responders and remitters as compared to conventional treatment in MDD in Indian patients.

The Effect of Additional Virtual Reality Training on Balance in Children with Cerebral Palsy after Lower Limb Surgery: A Feasibility Study.

PubMed

Meyns, Pieter; Pans, Liene; Plasmans, Kaat; Heyrman, Lieve; Desloovere, Kaat; Molenaers, Guy

2017-02-01

Impaired balance is disabling for children with cerebral palsy (CPc), especially for CPc who recently underwent lower limb surgery. Positive results of using virtual reality (VR) in balance rehabilitation have been published in several outpatient populations. We investigated the feasibility of applying additional VR training focused on sitting balance in CP inpatients of a rehabilitation center after lower limb surgery. Additionally, we investigated the rate of enjoyment of VR training compared with conventional physiotherapy. Eleven spastic CPc (4/7 males/females) following rehabilitation after lower limb orthopedic surgery were included (5-18 years). The control group received conventional physiotherapy. The intervention group received additional VR training. Balance was measured using the Trunk Control Measurement Scale every 3 weeks of the rehabilitation period. Enjoyment was analyzed using a 10-point Visual Analog Scale. Providing additional VR training was feasible in terms of recruitment, treatment adherence, and assessment adherence. Both groups improved sitting balance after therapy. The current games were not perceived as more enjoyable than conventional physiotherapy. Including additional VR training to conventional physiotherapy is feasible and might be promising to train sitting balance in CPc after lower limb surgery. Future research should take equal patient allocation and training duration between groups into consideration.

Incidence of Heterotopic Ossification after Surface and Conventional Total Hip Arthroplasty: A Comparative Study Using Anterolateral Approach and Indomethacin Prophylaxis

PubMed Central

Sandri, Andrea; Sambugaro, Elena

2013-01-01

The incidence and severity of heterotopic ossification (HO) in two homogeneous groups of patients that received surface replacement arthroplasty (SRA) and conventional total hip arthroplasty (THA) were evaluated retrospectively. Thirty-nine patients undergoing 42 hip resurfacing procedures and 41 primary cementless THAs through an anterolateral approach received a 10-day course of 150 mg/die of indomethacin postoperatively. The median surgical time was 190 minutes and 156 minutes, respectively (P < 0.003). At a minimum 1-year followup, the development of HO was assessed on standard X-ray using Brooker grading. Ectopic bone formation was detected in five cases (11.9%, two Brooker grade I and three grade II) in the SRA group and in 14 hips (34.1%, 12 grade I and two grade II) treated with conventional THA, but the difference was not significant (P < 0.11). No clinically relevant periprosthetic ossification (Brooker III or IV) occurred in both groups. Although the difference was not statistically significant, the incidence of HO after SRA was lower than conventional THA. More extensive soft tissue trauma, bone debris, and longer operative time in hip resurfacing are not likely to be absolute risk factors for HO. Further investigations including larger patient populations are needed to confirm these findings. PMID:23865045

76 FR 45907 - Implementation of the Amendments to the International Convention on Standards of Training...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-01

...The Coast Guard proposes to amend the existing regulations that implement the International Convention on Standards of Training, Certification and Watchkeeping for Seafarers, 1978, as amended (STCW Convention), as well as the Seafarer's Training, Certification and Watchkeeping Code (STCW Code). The changes proposed in this Supplemental Notice of Proposed Rulemaking (SNPRM) address the comments received from the public response to the Notice of Proposed Rulemaking (NPRM), in most cases through revisions based on those comments, and propose to incorporate the 2010 amendments to the STCW Convention that will come into force on January 1, 2012. In addition, this SNPRM proposes to make other non-STCW changes necessary to reorganize, clarify, and update these regulations.

Assessing the dose values received by patients during conventional radiography X-ray examinations and the technical condition of the equipment used for this purpose.

PubMed

Bekas, Marcin; Pachocki, Krzysztof A; Waśniewska, Elżbieta; Bogucka, Dagmara; Magiera, Andrzej

2014-01-01

X-ray examination is associated with patient exposure to ionizing radiation. Dose values depend on the type of medical procedure used, the X-ray unit technical condition and exposure conditions selected. The aim of this study was to determine the dose value received by patients during certain conventional radiography X-ray examinations and to assess the technical condition of medical equipment used for this purpose. The study covered the total number of 118 conventional diagnostic X-ray units located in the Masovian Voivodeship. The methodology used to assess the conventional diagnostic X-ray unit technical condition and the measurement of the radiation dose rate received by patients are based on test procedures developed by the Department of Radiation Protection and Radiobiology of the National Institute of Public Health - National Institute of Hygiene (Warszawa, Poland) accredited for compliance with PN-EN 17025 standard by the Polish Centre for Accreditation. It was found that 84.7% of X-ray units fully meet the criteria set out in the Polish legislation regarding the safe use of ionizing radiation in medicine, while 15.3% of the units do not meet some of them. The broadest dose value range was recorded for adult patients. Particularly, during lateral (LATl) lumbar spine radiography the recorded entrance surface dose (ESD) values ranged from 283.5 to 7827 µGy (mean: 2183.3 µGy). It is absolutely necessary to constantly monitor the technical condition of all X-ray units, because it affects population exposure to ionizing radiation. Furthermore, it is essential to raise radiographers' awareness of the effects that ionizing radiation exposure can have on the human body.

Oxygen therapy for corneal edema after cataract surgery.

PubMed

Sharifipour, Farideh; Panahi-Bazaz, Mahmoodreza; Idani, Esmaeil; Hajizadeh, Maryam; Saki, Azadeh

2015-07-01

To evaluate the effects of oxygen therapy on corneal edema after cataract surgery. Imam Khomeini Hospital, Ahvaz, Iran. Randomized controlled trial. Patients with severe corneal edema were randomized into 3 groups. Group 1 (control) received conventional therapy including topical sodium chloride, timolol, and betamethasone. Group 2 received the same therapy in addition to systemic normobaric oxygen at a flow rate of 10 L/min for 1 hour twice daily for 3 weeks. Group 3 received conventional therapy and transcorneal oxygen at a flow rate of 5 L/min for 1 hour twice daily for 3 weeks. Preoperative pachymetry and specular microscopy were performed. Pachymetry was performed 1, 3, 5, 7, 10, and 14 days postoperatively. At 1, 3 and 12 months, pachymetry and specular microscopy were performed. The study enrolled 45 patients. Preoperatively, there was no significant difference between the groups. Pachymetry was more than 1000 μm 1 day postoperatively in all patients. The preoperative pachymetry was restored in 14 days in Group 3 only. After 1 year, the endothelial cell count (ECC) was 1603 cells/mm(2), 1693 cells/mm(2), and 1911 cells/mm(2) with a loss of 37%, 32%, and 25% in Group 1, Group 2, and Group 3, respectively (P = .034, Groups 1 and 3). Group 3 had a higher ECC than the control group at 3 months (P = .037) and 1 year (P = .025). One patient in Group 1 and 1 patient in Group 2 developed bullous keratopathy. Transcorneal oxygen decreased corneal edema more rapidly than conventional and systemic oxygen therapies and preserved more endothelial cells than conventional therapy. No author has a financial or proprietary interest in any material or method mentioned. Copyright © 2015 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Population pharmacokinetics of conventional and intermittent dosing of liposomal amphotericin B in adults: a first critical step for rational design of innovative regimens.

PubMed

Hope, William W; Goodwin, Joanne; Felton, Timothy W; Ellis, Michael; Stevens, David A

2012-10-01

There is increased interest in intermittent regimen of liposomal amphotericin B, which may facilitate use in ambulatory settings. Little is known, however, about the most appropriate dosage and schedule of administration. Plasma pharmacokinetic data were acquired from 30 patients receiving liposomal amphotericin B for empirical treatment of suspected invasive fungal infection. Two cohorts were studied. The first cohort received 3 mg of liposomal amphotericin B/kg of body weight/day; the second cohort received 10 mg of liposomal amphotericin B/kg at time zero, followed by 5 mg/kg at 48 and 120 h. The levels of liposomal amphotericin B were measured by high-pressure liquid chromatography (HPLC). The pharmacokinetics were estimated by using a population methodology. Monte Carlo simulations were performed. D-optimal design was used to identify maximally informative sampling times for both conventional and intermittent regimens for future studies. A three-compartment pharmacokinetic model best described the data. The pharmacokinetics for both conventional and intermittent dosing were linear. The estimates for the mean (standard deviation) for clearance and the volume of the central compartment were 1.60 (0.85) liter/h and 20.61 (15.27) liters, respectively. Monte Carlo simulations demonstrated considerable variability in drug exposure. Bayesian estimates for clearance and volume increased in a linear manner with weight, but only the former was statistically significant (P = 0.039). D-optimal design provided maximally informative sampling times for future pharmacokinetic studies. The pharmacokinetics of a conventional and an intermittently administered high-dose regimen liposomal amphotericin B are linear. Further pharmacokinetic-pharmacodynamic preclinical and clinical studies are required to identify safe and effective intermittent regimens.

Population Pharmacokinetics of Conventional and Intermittent Dosing of Liposomal Amphotericin B in Adults: a First Critical Step for Rational Design of Innovative Regimens

PubMed Central

Goodwin, Joanne; Felton, Timothy W.; Ellis, Michael; Stevens, David A.

2012-01-01

There is increased interest in intermittent regimen of liposomal amphotericin B, which may facilitate use in ambulatory settings. Little is known, however, about the most appropriate dosage and schedule of administration. Plasma pharmacokinetic data were acquired from 30 patients receiving liposomal amphotericin B for empirical treatment of suspected invasive fungal infection. Two cohorts were studied. The first cohort received 3 mg of liposomal amphotericin B/kg of body weight/day; the second cohort received 10 mg of liposomal amphotericin B/kg at time zero, followed by 5 mg/kg at 48 and 120 h. The levels of liposomal amphotericin B were measured by high-pressure liquid chromatography (HPLC). The pharmacokinetics were estimated by using a population methodology. Monte Carlo simulations were performed. D-optimal design was used to identify maximally informative sampling times for both conventional and intermittent regimens for future studies. A three-compartment pharmacokinetic model best described the data. The pharmacokinetics for both conventional and intermittent dosing were linear. The estimates for the mean (standard deviation) for clearance and the volume of the central compartment were 1.60 (0.85) liter/h and 20.61 (15.27) liters, respectively. Monte Carlo simulations demonstrated considerable variability in drug exposure. Bayesian estimates for clearance and volume increased in a linear manner with weight, but only the former was statistically significant (P = 0.039). D-optimal design provided maximally informative sampling times for future pharmacokinetic studies. The pharmacokinetics of a conventional and an intermittently administered high-dose regimen liposomal amphotericin B are linear. Further pharmacokinetic-pharmacodynamic preclinical and clinical studies are required to identify safe and effective intermittent regimens. PMID:22869566

The Right to Inclusive Education under International Law: Following Italy's Lead

ERIC Educational Resources Information Center

Kanter, Arlene S.; Damiani, Michelle L.; Ferri, Beth A.

2014-01-01

It is estimated in the world today, that more than one billion people have a disability (World Health Organization, 2011). Many people with disabilities receive no education, and, of those who do, few receive an education on an equal basis with their non-disabled peers. In 2006, the United Nations adopted the Convention on the Rights of Persons…

Reinforcement for percutaneous nephrostomy tubes with a new technique.

PubMed

Zhou, Tie; Gao, Xiaofeng; Yang, Cheng; Peng, Yonghan; Xiao, Liang; Xu, Chuanliang; Wang, Linhui; Hou, Jianguo; Sun, Yinghao

2011-01-01

Percutaneous nephrostomy (PCN) still plays a significant role in decompressing the renal collecting system. Percutaneous nephrostomy tubes (PNTs), however, which are flexible and may not be protected well by patients, are vulnerable to mechanical drag, although they are carefully fixed to the skin with silk suture. We developed a simple method to reinforce the nephrostomy tube against dislodgement from the skin. A total of 133 adult patients underwent ultrasonography-guided PCN; 85 patients received a conventional method to fix the tubes, while the other 48 patients received a new one. We used a rubber drainage tube, about 2 cm long, sheared longitudinally, as the outer tube to encase the nephrostomy tube, and then sutured the cutting edges together with the skin suture to reinforce the nephrostomy tube. Compared with the 85 patients who received the conventional method, there was not any tube dislodgement after PCN in the 48 patients who received the new one at the end of 2 weeks (0 vs 7, P=0.049) and 4 weeks (0 vs 10, P=0.014) follow-up. This is a simple, effective, and inexpensive method that can significantly decrease the dislodgement incidence of PNTs and keep them fixed well after surgery.

Influence of maternal factors on the successful outcome of kangaroo mother care in low birth-weight infants: A randomized controlled trial.

PubMed

Lumbanraja, S N

2016-01-01

Kangaroo mother care (KMC) is associated with positive neonatal outcomes. Studies demonstrated significant influence of maternal factors on the success of applying KMC. To determine maternal factors that influence on anthropometric parameters in low birth weight babies that received kangaroo mother care. This is a randomized controlled study that involved low birth weight newborns. We randomly assigned newborns into two groups; a group who received KMC and a group who received conventional care. Maternal factors were recorded. We followed weight, length, and head circumferences of newborns for thirty days. A total of 40 newborns were included. Weight parameters were significantly higher in the KMC group than the conventional group. From maternal characteristics, only gestational age was found to influence increased head circumference in KMC group (p = 0.035); however, it did not affect the increase in weight or length. Maternal age, parity, education, mode of delivery, fetal sex, and initial Apgar score did not influence growth parameters in either groups. KMC was associated with increased weight gain in LBW infants. Gestational age influences head growth in infants who received KMC.

A Prospective Open-Label Study of Combined Treatment for Idiopathic Parkinson's Disease Using Acupuncture and Bee Venom Acupuncture as an Adjunctive Treatment.

PubMed

Doo, Kyeong-Hee; Lee, Ji-Hyun; Cho, Seung-Yeon; Jung, Woo-Sang; Moon, Sang-Kwan; Park, Jung-Mi; Ko, Chang-Nam; Kim, Ho; Park, Hi-Joon; Park, Seong-Uk

2015-10-01

The purpose of this study was to examine the effectiveness and safety of combined treatment using acupuncture and bee venom acupuncture (BVA) as an adjunctive treatment for idiopathic Parkinson's disease (PD). Eleven patients (7 men and 4 women) with idiopathic PD who had been receiving a stable dose of anti-parkinsonian medication for at least 4 weeks. Participants received conventional treatment for 12 weeks. Subsequently, they received additional treatment with acupuncture and BVA twice weekly for 12 weeks while still maintaining conventional treatment. All participants were assessed at baseline, 12 weeks, and 24 weeks by using the Unified Parkinson's Disease Rating Scale (UPDRS), the Parkinson's Disease Quality of Life Questionnaire (PDQL), the speed and number of steps required to walk 20 m, and the Beck Depression Inventory (BDI). Maximum excursion and directional control, measured by computerized dynamic posturography (Balance Master(®) System, NeuroCom, San Carlos, CA), were used to assess postural stability. Patients who underwent 12 weeks of twice-weekly combined treatment with acupuncture and BVA showed significant improvements in gait speed, PDQL score, activities of daily living (UPDRS part II), motor symptoms (UPDRS part III), and combined UPDRS part II+III scores compared with assessments after conventional treatment. Combined treatment with acupuncture and BVA showed promising results as a safe adjunctive therapy for PD.

A versatile microprocessor-controlled hybrid receiver. [with firmware control for operation over large frequency uncertainty

NASA Technical Reports Server (NTRS)

Grant, T. L.

1978-01-01

A hybrid receiver has been designed for the Galileo Project. The receiver, located on the Galileo Orbiter, will autonomously acquire and track signals from the first atmospheric probe of Jupiter as well as demodulate, bit-synchronize, and buffer the telemetry data. The receiver has a conventional RF and LF front end but performs multiple functions digitally under firmware control. It will be a self-acquiring receiver that operates under a large frequency uncertainty; it can accommodate different modulation types, bit rates, and other parameter changes via reprogramming. A breadboard receiver and test set demonstrate a preliminary version of the sequential detection process and verify the hypothesis that a fading channel does not reduce the probability of detection.

Usefulness of diffusion-weighted MR imaging for differentiating between benign and malignant superficial soft tissue tumours and tumour-like lesions

PubMed Central

Jeon, Ji Young; Lee, Min Hee; Lee, Sang Hoon; Shin, Myung Jin

2016-01-01

Objective: To evaluate the usefulness of adding diffusion-weighted imaging (DWI) with apparent diffusion coefficient (ADC) mapping to conventional 3.0-T MRI to differentiate between benign and malignant superficial soft-tissue masses (SSTMs). Methods: The institutional review board approved this study and informed consent was waived. The authors retrospectively analyzed conventional MR images including diffusion-weighted images (b-values: 0, 400, 800 s mm−2) in 60 histologically proven SSTMs (35 benign and 25 malignant) excluding lipomas. Two radiologists independently evaluated the conventional MRI alone and again with the additional DWI for the evaluation of malignant masses. The mean ADC values measured within an entire mass and the contrast-enhancing solid portion were used for quantitative analysis. Diagnostic performances were compared using receiver-operating characteristic analysis. Results: For an inexperienced reader, using only conventional MRI, the sensitivity, specificity and accuracy were 84%, 80% and 81.6%, respectively. When combining conventional MRI and DWI, the sensitivity, specificity and accuracy were 96%, 85.7% and 90%, respectively. Additional DWI influenced the improvement of the rate of correct diagnosis by 8.3% (5/60). For an experienced reader, additional DWI revealed the same accuracy of 86.7% without added value on the correct diagnosis. The group mean ADCs of malignant SSTMs were significantly lower than that of benign SSTMs (p < 0.001). The best diagnostic performance with respect to differentiation of SSTMs could be obtained when conventional MRI was assessed in combination with DWI. Conclusion: Adding qualitative and quantitative DWI to conventional MRI can improve the diagnostic performance for the differentiation between benign and malignant SSTMs. Advances in knowledge: Because the imaging characteristics of many malignant superficial soft-tissue lesions overlap with those of benign ones, inadequate surgical resection due to misinterpretation of MRI often occurs. Adding DWI to conventional MRI yields greater diagnostic performances [area under the receiver-operating characteristic curve (AUC), 0.83–0.99] than does the use of conventional MRI alone (AUC, 0.71–0.93) in the evaluation of malignant superficial masses by inexperienced readers. PMID:26892266

Suitable closure for post-duodenal endoscopic resection taking medical costs into consideration

PubMed Central

Mori, Hirohito; Ayaki, Maki; Kobara, Hideki; Fujihara, Shintaro; Nishiyama, Noriko; Matsunaga, Tae; Yachida, Tatsuo; Masaki, Tsutomu

2015-01-01

AIM: To compare closure methods, closure times and medical costs between two groups of patients who had post-endoscopic resection (ER) artificial ulcer floor closures. METHODS: Nineteen patients with duodenal adenoma, early duodenal cancer, and subepithelial tumors that received ER between September 2009 and September 2014 at Kagawa University Hospital and Ehime Rosai Hospital, an affiliated hospital of Kagawa University, were included in the study. We retrospectively compared two groups of patients who received post-ER artificial ulcer floor closure: the conventional clip group vs the over-the-scope clip (OTSC) group. Delayed bleeding, procedure time of closure, delayed perforation, total number of conventional clips and OTSCs and medical costs were analyzed. RESULTS: Although we observed delayed bleeding in three patients in the conventional clip group, we observed no delayed bleeding in the OTSC group (P = 0.049). We did not observe perforation in either group. The mean procedure times for ulcer closure were 33.26 ± 12.57 min and 9.71 ± 2.92 min, respectively (P = 0.0001). The resection diameters were 18.8 ± 1.30 mm and 22.9 ± 1.21 mm for the conventional clip group and the OTSC group, respectively, with significant difference (P = 0.039). As for medical costs, the costs of all conventional clips were USD $1257 and the costs of OTSCs were $7850 (P = 0.005). If the post-ER ulcer is under 20 mm in diameter, a conventional clip closure may be more suitable with regard to the prevention of delayed perforation and to medical costs. CONCLUSION: If the post-ER ulcer is over 20 mm, the OTSC closure should be selected with regard to safety and reliable closure even if there are high medical costs. PMID:25954101

Web-Based Versus Conventional Training for Medical Students on Infant Gross Motor Screening.

PubMed

Pusponegoro, Hardiono D; Soebadi, Amanda; Surya, Raymond

2015-12-01

Early detection of developmental abnormalities is important for early intervention. A simple screening method is needed for use by general practitioners, as is an effective and efficient training method. This study aims to evaluate the effectiveness, acceptability, and usability of Web-based training for medical students on a simple gross motor screening method in infants. Fifth-year medical students at University of Indonesia in Jakarta were randomized into two groups. A Web-based training group received online video modules, discussions, and assessments (at www.schoology.com ). A conventional training group received a 1-day live training using the same module. Both groups completed identical pre- and posttests and the User Satisfaction Questionnaire (USQ). The Web-based group also completed the System Usability Scale (SUS). The module was based on a gross motor screening method used in the World Health Organization Multicentre Growth Reference Study. There were 39 and 32 subjects in the Web-based and conventional groups, respectively. Mean pretest versus posttest scores (correct answers out of 20) were 9.05 versus 16.95 (p=0.0001) in the Web-based group and 9.31 versus 16.88 (p=0.0001) in the conventional group. Mean difference between pre- and posttest scores did not differ significantly between the Web-based and conventional groups (mean [standard deviation], 7.56 [3.252] versus 7.90 [5.170]; p=0.741]. Both training methods were acceptable based on USQ scores. Based on SUS scores, the Web-based training had good usability. Web-based training is an effective, efficient, and acceptable training method for medical students on simple infant gross motor screening and is as effective as conventional training.

Assessment of the efficacy of the utilisation of conventional and electric toothbrushes by the elderly.

PubMed

Nobre, Cristiane V C; Gomes, Ana M M; Gomes, Ana P M; Gomes, Antonio A; Nascimento, Ana P C

2014-07-17

Objective:  To evaluate the efficacy of electric and conventional toothbrushes for a group of elderly individuals. Background:  Although the electric toothbrush has been recommended for elderly individuals, there had previously never been a study regarding its efficacy. Material and methods:  Sixty independent elders of both genders with different oral conditions from the Center Adult Day Vitória, Espírito Santo, Brazil, were randomly divided into two groups of 30 individuals. One group received the Oral B CrossAction Power electric toothbrush, whereas the other received a conventional Bitufo Class 32 soft toothbrush to perform oral hygiene. The bacterial plaque index (O'Leary Plaque Index) and DMFT index were assessed as a measure of oral hygiene and oral health. The data were analysed using the Shapiro-Wilk, Mann-Whitney and Wilcoxon tests. Results:  The results of the efficacy of the Oral B Cross Action Power electric toothbrush demonstrated that on the 7th and 15th days, the bacterial plaque indexes were 24.91 ± 12.81 and 22.11 ± 14.46, respectively, which corresponds to a 50.24% removal of bacterial plaque on the 7th and 55.83% on the 15th days. Although the electric toothbrush removed more bacterial plaque than the conventional toothbrush, the difference was not statistically significant. Conclusion:  Both the conventional and the electric toothbrushes were effective in removing bacterial plaque within the elderly group. More studies are necessary to test the efficacy of electric toothbrushes in relation to conventional toothbrushes for elderly patients. © 2012 The Gerodontology Society and John Wiley & Sons A/S.

Short daily hemodialysis is associated with lower plasma FGF23 levels when compared with conventional hemodialysis

PubMed Central

Zaritsky, Joshua; Rastogi, Anjay; Fischmann, George; Yan, Jieshi; Kleinman, Kenneth; Chow, Georgina; Gales, Barbara; Salusky, Isidro B.; Wesseling-Perry, Katherine

2014-01-01

Background The utilization of short-term daily hemodialysis has increased over the last few years, but little is known on its effects on the control of serum phosphate and fibroblast growth factor 23 (FGF23) levels. Methods We therefore performed a cross-sectional study to compare FGF23 levels as well as other biochemical variables between 24 patients undergoing short daily hemodialysis using the NxStage System® and 54 patients treated with conventional in-center hemodialysis. FGF23 levels were measured using the second-generation Immutopics® C-terminal assay. Results Short daily hemodialysis patients were younger than patients on conventional hemodialysis but there were no differences between groups in the duration of end-stage renal disease nor in the number of patients with residual renal function. A greater number of short daily hemodialysis patients received vitamin D sterol therapy than did conventional in-center hemodialysis patients while there were no differences in the use of different phosphate binders and calcimimetic therapy between groups. Overall serum calcium, phosphorus and intact parathyroid hormone levels were similar between groups. While serum phosphorus levels correlated with FGF23 concentrations in each group separately [r = 0.522 (P < 0.01) and r = 0.42 (P < 0.01) in short daily and conventional in-center hemodialysis, respectively], FGF23 levels were lower [823 RU/mL (263, 2169)] in the patients receiving short daily hemodialysis than in patients treated with conventional hemodialysis [2521 RU/mL (909, 5556)] (P < 0.01 between groups). Conclusions These findings demonstrate that FGF23 levels are significantly lower in short daily hemodialysis patients and suggest that FGF23 levels may be a more sensitive biomarker of cumulative phosphate burden than single or multiple serum phosphorus determinations in patients treated with hemodialysis. PMID:24009282

Short daily hemodialysis is associated with lower plasma FGF23 levels when compared with conventional hemodialysis.

PubMed

Zaritsky, Joshua; Rastogi, Anjay; Fischmann, George; Yan, Jieshi; Kleinman, Kenneth; Chow, Georgina; Gales, Barbara; Salusky, Isidro B; Wesseling-Perry, Katherine

2014-02-01

The utilization of short-term daily hemodialysis has increased over the last few years, but little is known on its effects on the control of serum phosphate and fibroblast growth factor 23 (FGF23) levels. We therefore performed a cross-sectional study to compare FGF23 levels as well as other biochemical variables between 24 patients undergoing short daily hemodialysis using the NxStage System® and 54 patients treated with conventional in-center hemodialysis. FGF23 levels were measured using the second-generation Immutopics® C-terminal assay. Short daily hemodialysis patients were younger than patients on conventional hemodialysis but there were no differences between groups in the duration of end-stage renal disease nor in the number of patients with residual renal function. A greater number of short daily hemodialysis patients received vitamin D sterol therapy than did conventional in-center hemodialysis patients while there were no differences in the use of different phosphate binders and calcimimetic therapy between groups. Overall serum calcium, phosphorus and intact parathyroid hormone levels were similar between groups. While serum phosphorus levels correlated with FGF23 concentrations in each group separately [r=0.522 (P<0.01) and r=0.42 (P<0.01) in short daily and conventional in-center hemodialysis, respectively], FGF23 levels were lower [823 RU/mL (263, 2169)] in the patients receiving short daily hemodialysis than in patients treated with conventional hemodialysis [2521 RU/mL (909, 5556)] (P<0.01 between groups). These findings demonstrate that FGF23 levels are significantly lower in short daily hemodialysis patients and suggest that FGF23 levels may be a more sensitive biomarker of cumulative phosphate burden than single or multiple serum phosphorus determinations in patients treated with hemodialysis.

Suitable closure for post-duodenal endoscopic resection taking medical costs into consideration.

PubMed

Mori, Hirohito; Ayaki, Maki; Kobara, Hideki; Fujihara, Shintaro; Nishiyama, Noriko; Matsunaga, Tae; Yachida, Tatsuo; Masaki, Tsutomu

2015-05-07

To compare closure methods, closure times and medical costs between two groups of patients who had post-endoscopic resection (ER) artificial ulcer floor closures. Nineteen patients with duodenal adenoma, early duodenal cancer, and subepithelial tumors that received ER between September 2009 and September 2014 at Kagawa University Hospital and Ehime Rosai Hospital, an affiliated hospital of Kagawa University, were included in the study. We retrospectively compared two groups of patients who received post-ER artificial ulcer floor closure: the conventional clip group vs the over-the-scope clip (OTSC) group. Delayed bleeding, procedure time of closure, delayed perforation, total number of conventional clips and OTSCs and medical costs were analyzed. Although we observed delayed bleeding in three patients in the conventional clip group, we observed no delayed bleeding in the OTSC group (P = 0.049). We did not observe perforation in either group. The mean procedure times for ulcer closure were 33.26 ± 12.57 min and 9.71 ± 2.92 min, respectively (P = 0.0001). The resection diameters were 18.8 ± 1.30 mm and 22.9 ± 1.21 mm for the conventional clip group and the OTSC group, respectively, with significant difference (P = 0.039). As for medical costs, the costs of all conventional clips were USD $1257 and the costs of OTSCs were $7850 (P = 0.005). If the post-ER ulcer is under 20 mm in diameter, a conventional clip closure may be more suitable with regard to the prevention of delayed perforation and to medical costs. If the post-ER ulcer is over 20 mm, the OTSC closure should be selected with regard to safety and reliable closure even if there are high medical costs.

B1-control receive array coil (B-RAC) for reducing B1+ inhomogeneity in abdominal imaging at 3T-MRI

NASA Astrophysics Data System (ADS)

Kaneko, Yukio; Soutome, Yoshihisa; Habara, Hideta; Bito, Yoshitaka; Ochi, Hisaaki

2018-02-01

B1+ inhomogeneity in the human body increases as the nuclear magnetic resonance (NMR) frequency increases. Various methods have thus been developed to reduce B1+ inhomogeneity, such as a dielectric pad, a coupling coil, parallel transmit, and radio-frequency (RF) shimming. However, B1+ inhomogeneity still remains in some cases of abdominal imaging. In this study, we developed a B1-control receive array coil (B-RAC). Unlike the conventional receive array coil, B-RAC reduces B1+ inhomogeneity by using additional PIN diodes to generate the inductive loop during the RF transmit period. The inductive loop can generate dense and sparse regions of the magnetic flux, which can be used to compensate for B1+ inhomogeneity. First, B-RAC is modeled in the numerical simulation, and the spatial distributions of B1+ in a phantom and a human model were analyzed. Next, we fabricated a 12-channel B-RAC and measured receive sensitivity and B1+ maps in a 3T-MRI experiment. It was demonstrated that B-RAC can reduce B1+ inhomogeneity in the phantom and human model without increasing the maximum local specific absorption rate (SAR) in the body. B-RAC was also found to have almost the same the receive sensitivity as the conventional receive coil. Using RF shimming combined with B-RAC was revealed to more effectively reduce B1+ inhomogeneity than using only RF shimming. Therefore, B-RAC can reduce B1+ inhomogeneity while maintaining the receive sensitivity.

Aerodynamic Performance of a Compact, High Work-Factor Centrifugal Compressor at the Stage and Subcomponent Level

NASA Technical Reports Server (NTRS)

Braunscheidel, Edward P.; Welch, Gerard E.; Skoch, Gary J.; Medic, Gorazd; Sharma, Om P.

2015-01-01

The measured aerodynamic performance of a compact, high work-factor, single-stage centrifugal compressor, comprising an impeller, diffuser, 90deg-bend, and exit guide vane is reported. Performance levels are based on steady-state total-pressure and total-temperature rake and angularity-probe data acquired at key machine rating planes during recent testing at NASA Glenn Research Center. Aerodynamic performance at the stage level is reported for operation between 70 to 105 percent of design corrected speed, with subcomponent (impeller, diffuser, and exit-guide-vane) flow field measurements presented and discussed at the 100 percent design-speed condition. Individual component losses from measurements are compared with pre-test CFD predictions on a limited basis.

Directivity in NGA earthquake ground motions: Analysis using isochrone theory

USGS Publications Warehouse

Spudich, P.; Chiou, B.S.J.

2008-01-01

We present correction factors that may be applied to the ground motion prediction relations of Abrahamson and Silva, Boore and Atkinson, Campbell and Bozorgnia, and Chiou and Youngs (all in this volume) to model the azimuthally varying distribution of the GMRotI50 component of ground motion (commonly called 'directivity') around earthquakes. Our correction factors may be used for planar or nonplanar faults having any dip or slip rake (faulting mechanism). Our correction factors predict directivity-induced variations of spectral acceleration that are roughly half of the strike-slip variations predicted by Somerville et al. (1997), and use of our factors reduces record-to-record sigma by about 2-20% at 5 sec or greater period. ?? 2008, Earthquake Engineering Research Institute.

Metamorphism of brecciated ANT rocks - Anorthositic troctolite 72559 and norite 78527. [Anorthositic-Noritic-Troctolitic

NASA Technical Reports Server (NTRS)

Nehru, C. E.; Warner, R. D.; Keil, K.; Taylor, G. J.

1978-01-01

Rake samples 72559 and 78527 are annealed rocks of ANT-suite mineralogy and bulk composition. The rocks were presumably derived from ancient lunar highland ANT rocks of cumulate origin. Sample 72559 is polymict and its precursors were anorthositic-troctolitic in composition. Sample 78527 is monomict and of noritic derivation. The precursors were brecciated due to impact processes; 72559 shows evidence of some impact melting. The samples were thermally metamorphosed forming rocks with granoblastic matrix textures. Coexisting matrix pyroxenes indicate equilibration temperatures of 950-1000 C for both rocks. Accessory opaque oxide minerals in the rocks show rather wide compositional variations. These probably primarily reflect compositional ranges inherited from the precursor/s with little integranular equilibration among them during metamorphism.

Aerodynamic Performance of a Compact, High Work-Factor Centrifugal Compressor at the Stage and Subcomponent Level

NASA Technical Reports Server (NTRS)

Braunscheidel, Edward P.; Welch, Gerard E.; Skoch, Gary J.; Medic, Gorazd; Sharma, Om P.

2014-01-01

The measured aerodynamic performance of a compact, high work-factor, single-stage centrifugal compressor, comprising an impeller, diffuser, 90º-bend, and exit guide vane is reported. Performance levels are based on steady-state total-pressure and total-temperature rake and angularity-probe data acquired at key machine rating planes during recent testing at NASA Glenn Research Center. Aerodynamic performance at the stage level is reported for operation between 70 to 105% of design corrected speed, with subcomponent (impeller, diffuser, and exit-guide-vane) flow field measurements presented and discussed at the 100% design-speed condition. Individual component losses from measurements are compared with pre-test CFD predictions on a limited basis.

Monthly plasmapheresis for systemic lupus erythematosus with diffuse proliferative glomerulonephritis: a pilot study

PubMed Central

Clark, William F.; Lindsay, Robert M.; Cattran, Daniel C.; Chodirker, William B.; Barnes, Colin C.; Linton, Adam L.

1981-01-01

Twelve patients with systemic lupus erythematosus and biopsy-proved diffuse proliferative glomerulonephritis were randomly allocated to a control group (to continue receiving conventional therapy only) or to a plasmapheresis group (to receive conventional therapy along with one 4-I plasma exchange a month). The six patients treated with plasmapheresis had better preservation of renal function, reduced disease activity, fewer admissions to hospital and less need for steroid and immunosuppressive therapy than the six control patients. The patients treated with plasmapheresis also showed evidence of reduced immunologic activity and had no side effects attributable to the plasma exchange. These results suggest that monthly plasma exchange should be assessed in a controlled randomized trial as a possible therapeutic adjunct in patients with systemic lupus erythematosus and diffuse proliferative glomerulonephritis. PMID:7272867

High dynamic GPS receiver validation demonstration

NASA Technical Reports Server (NTRS)

Hurd, W. J.; Statman, J. I.; Vilnrotter, V. A.

1985-01-01

The Validation Demonstration establishes that the high dynamic Global Positioning System (GPS) receiver concept developed at JPL meets the dynamic tracking requirements for range instrumentation of missiles and drones. It was demonstrated that the receiver can track the pseudorange and pseudorange rate of vehicles with acceleration in excess of 100 g and jerk in excess of 100 g/s, dynamics ten times more severe than specified for conventional High Dynamic GPS receivers. These results and analytic extensions to a complete system configuration establish that all range instrumentation requirements can be met. The receiver can be implemented in the 100 cu in volume required by all missiles and drones, and is ideally suited for transdigitizer or translator applications.

Effects of inspiratory muscle training on balance ability and abdominal muscle thickness in chronic stroke patients

PubMed Central

Oh, Dongha; Kim, Gayeong; Lee, Wanhee; Shin, Mary Myong Sook

2016-01-01

[Purpose] This study evaluated the effects of inspiratory muscle training on pulmonary function, deep abdominal muscle thickness, and balance ability in stroke patients. [Subjects] Twenty-three stroke patients were randomly allocated to an experimental (n = 11) or control group (n = 12). [Methods] The experimental group received inspiratory muscle training-based abdominal muscle strengthening with conventional physical therapy; the control group received standard abdominal muscle strengthening with conventional physical therapy. Treatment was conducted 20 minutes per day, 3 times per week for 6 weeks. Pulmonary function testing was performed using an electronic spirometer. Deep abdominal muscle thickness was measured by ultrasonography. Balance was measured using the Berg balance scale. [Results] Forced vital capacity, forced expiratory volume in 1 second, deep abdominal muscle thickness, and Berg balance scale scores were significantly improved in the experimental group than in the control group. [Conclusion] Abdominal muscle strengthening accompanied by inspiratory muscle training is recommended to improve pulmonary function in stroke patients, and may also be used as a practical adjunct to conventional physical therapy. PMID:26957739

Mirror therapy for distal radial fractures: A pilot randomized controlled study.

PubMed

Bayon-Calatayud, Manuel; Benavente-Valdepeñas, Ana Maria; Del Prado Vazquez-Muñoz, Maria

2016-10-12

To investigate the efficacy of mirror therapy in reducing pain and disability in patients with distal radial fractures. Pilot randomized controlled study. Twenty-two patients with closed distal radial fracture. Patients were randomly assigned to experimental (= 11) or control (= 11) groups. Researchers were blinded to group allocation. Both groups received conventional physiotherapy. In addition, the experimental group had 15 sessions of mirror therapy (a daily session, 30 min). The control group received the same amount of conventional occupational therapy. Assessment was made from baseline to post-treatment. Pain was measured on a visual analogue scale (VAS). Active wrist extension and Quick-DASH (Disabilities of Arm, Shoulder and Hand) were used to assess functional recovery. Pain, disability, and range of motion improved for both groups after intervention. No significant post-treatment differences were found between groups in Quick-DASH (= 0.409), active wrist extension (= 0.191) and VAS scores (= 0.807). There was no significant difference in active wrist extension between groups. Mirror therapy was not superior to conventional occupational therapy in reducing pain and disability.

Modeling and Analysis of Wholesale Electricity Market Design. Understanding the Missing Money Problem. December 2013 - January 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Papalexopoulos, A.; Hansen, C.; Perrino, D.

This project examined the impact of renewable energy sources, which have zero incremental energy costs, on the sustainability of conventional generation. This “missing money” problem refers to market outcomes in which infra-marginal energy revenues in excess of operations and maintenance (O&M) costs are systematically lower than the amortized costs of new entry for a marginal generator. The problem is caused by two related factors: (1) conventional generation is dispatched less, and (2) the price that conventional generation receives for its energy is lower. This lower revenue stream may not be sufficient to cover both the variable and fixed costs ofmore » conventional generation. In fact, this study showed that higher wind penetrations in the Electric Reliability Council of Texas (ERCOT) system could cause many conventional generators to become uneconomic.« less

Comparison of performance due to guided hyperlearning, unguided hyperlearning, and conventional learning in mathematics: an empirical study

NASA Astrophysics Data System (ADS)

Fathurrohman, Maman; Porter, Anne; Worthy, Annette L.

2014-07-01

In this paper, the use of guided hyperlearning, unguided hyperlearning, and conventional learning methods in mathematics are compared. The design of the research involved a quasi-experiment with a modified single-factor multiple treatment design comparing the three learning methods, guided hyperlearning, unguided hyperlearning, and conventional learning. The participants were from three first-year university classes, numbering 115 students in total. Each group received guided, unguided, or conventional learning methods in one of the three different topics, namely number systems, functions, and graphing. The students' academic performance differed according to the type of learning. Evaluation of the three methods revealed that only guided hyperlearning and conventional learning were appropriate methods for the psychomotor aspects of drawing in the graphing topic. There was no significant difference between the methods when learning the cognitive aspects involved in the number systems topic and the functions topic.

Wii-based interactive video games as a supplement to conventional therapy for rehabilitation of children with cerebral palsy: A pilot, randomized controlled trial.

PubMed

Sajan, Jane Elizabeth; John, Judy Ann; Grace, Pearlin; Sabu, Sneha Sara; Tharion, George

2017-08-01

To assess the effect of interactive video gaming (IVG) with Nintendo Wii (Wii) supplemented to conventional therapy in rehabilitation of children with cerebral palsy (CP). Randomized, controlled, assessor-blinded study. Children with CP; 10 children each in the control and intervention groups. IVG using Wii, given as a supplement to conventional therapy, for 45 min per day, 6 days a week for 3 weeks. The children in the control group received conventional therapy alone. Posture control and balance, upper limb function, visual-perceptual skills, and functional mobility. Significant improvement in upper limb functions was seen in the intervention group but not in the control group. Improvements in balance, visual perception, and functional mobility were not significantly different between control and intervention groups. Wii-based IVG may be offered as an effective supplement to conventional therapy in the rehabilitation of children with CP.

Design and baseline characteristics of the Food4Me study: a web-based randomised controlled trial of personalised nutrition in seven European countries.

PubMed

Celis-Morales, Carlos; Livingstone, Katherine M; Marsaux, Cyril F M; Forster, Hannah; O'Donovan, Clare B; Woolhead, Clara; Macready, Anna L; Fallaize, Rosalind; Navas-Carretero, Santiago; San-Cristobal, Rodrigo; Kolossa, Silvia; Hartwig, Kai; Tsirigoti, Lydia; Lambrinou, Christina P; Moschonis, George; Godlewska, Magdalena; Surwiłło, Agnieszka; Grimaldi, Keith; Bouwman, Jildau; Daly, E J; Akujobi, Victor; O'Riordan, Rick; Hoonhout, Jettie; Claassen, Arjan; Hoeller, Ulrich; Gundersen, Thomas E; Kaland, Siv E; Matthews, John N S; Manios, Yannis; Traczyk, Iwona; Drevon, Christian A; Gibney, Eileen R; Brennan, Lorraine; Walsh, Marianne C; Lovegrove, Julie A; Alfredo Martinez, J; Saris, Wim H M; Daniel, Hannelore; Gibney, Mike; Mathers, John C

2015-01-01

Improving lifestyle behaviours has considerable potential for reducing the global burden of non-communicable diseases, promoting better health across the life-course and increasing well-being. However, realising this potential will require the development, testing and implementation of much more effective behaviour change interventions than are used conventionally. Therefore, the aim of this study was to conduct a multi-centre, web-based, proof-of-principle study of personalised nutrition (PN) to determine whether providing more personalised dietary advice leads to greater improvements in eating patterns and health outcomes compared to conventional population-based advice. A total of 5,562 volunteers were screened across seven European countries; the first 1,607 participants who fulfilled the inclusion criteria were recruited into the trial. Participants were randomly assigned to one of the following intervention groups for a 6-month period: Level 0-control group-receiving conventional, non-PN advice; Level 1-receiving PN advice based on dietary intake data alone; Level 2-receiving PN advice based on dietary intake and phenotypic data; and Level 3-receiving PN advice based on dietary intake, phenotypic and genotypic data. A total of 1,607 participants had a mean age of 39.8 years (ranging from 18 to 79 years). Of these participants, 60.9 % were women and 96.7 % were from white-European background. The mean BMI for all randomised participants was 25.5 kg m(-2), and 44.8 % of the participants had a BMI ≥ 25.0 kg m(-2). Food4Me is the first large multi-centre RCT of web-based PN. The main outcomes from the Food4Me study will be submitted for publication during 2015.

Self organization of wireless sensor networks using ultra-wideband radios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dowla, Farid U; Nekoogar, Franak; Spiridon, Alex

A novel UWB communications method and system that provides self-organization for wireless sensor networks is introduced. The self-organization is in terms of scalability, power conservation, channel estimation, and node synchronization in wireless sensor networks. The UWB receiver in the present invention adds two new tasks to conventional TR receivers. The two additional units are SNR enhancing unit and timing acquisition and tracking unit.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qin, Rosie; Olson, Adam; Singh, Bhavana

Purpose: Ipilimumab and radiation therapy (RT) are standard treatments for advanced melanoma; preclinical models suggest the potential for synergy. However, limited clinical information exists regarding safety and optimal timing of the combination. Methods and Materials: We reviewed the records of consecutive patients with unresectable stage 3 or 4 melanoma treated with ipilimumab. Patients were categorized as having received RT or not. Differences were estimated between these 2 cohorts. Results: We identified 88 patients treated with ipilimumab. At baseline, the ipilimumab-plus-RT group (n=44) had more unfavorable characteristics. Despite this, overall survival, progression-free survival, and both immune-related and non–immune-related toxicity were notmore » statistically different (P=.67). Patients who received ipilimumab before RT had an increased duration of irradiated tumor response compared with patients receiving ipilimumab after RT (74.7% vs 44.8% at 12 months; P=.01, log-rank test). In addition, patients receiving ablative RT had non–statistically significantly improved median overall survival (19.6 vs 10.2 months), as well as 6-month (95.1% vs 72.7%) and 12-month (79.7% vs 48.5%) survival rates, compared with those treated with conventionally fractionated RT. Conclusions: We found that both ablative and conventionally fractionated RT can be safely administered with ipilimumab without a clinically apparent increase in toxicity. Patients who received ipilimumab before RT had an increased duration of irradiated tumor response.« less

Evaluation of the White Test for the Intraoperative Detection of Bile Leakage

PubMed Central

Leelawat, Kawin; Chaiyabutr, Kittipong; Subwongcharoen, Somboon; Treepongkaruna, Sa-ad

2012-01-01

We assess whether the White test is better than the conventional bile leakage test for the intraoperative detection of bile leakage in hepatectomized patients. This study included 30 patients who received elective liver resection. Both the conventional bile leakage test (injecting an isotonic sodium chloride solution through the cystic duct) and the White test (injecting a fat emulsion solution through the cystic duct) were carried out in the same patients. The detection of bile leakage was compared between the conventional method and the White test. A bile leak was demonstrated in 8 patients (26.7%) by the conventional method and in 19 patients (63.3%) by the White test. In addition, the White test detected a significantly higher number of bile leakage sites compared with the conventional method (Wilcoxon signed-rank test; P < 0.001). The White test is better than the conventional test for the intraoperative detection of bile leakage. Based on our study, we recommend that surgeons investigating bile leakage sites during liver resections should use the White test instead of the conventional bile leakage test. PMID:22547901

Evaluation of the white test for the intraoperative detection of bile leakage.

PubMed

Leelawat, Kawin; Chaiyabutr, Kittipong; Subwongcharoen, Somboon; Treepongkaruna, Sa-Ad

2012-01-01

We assess whether the White test is better than the conventional bile leakage test for the intraoperative detection of bile leakage in hepatectomized patients. This study included 30 patients who received elective liver resection. Both the conventional bile leakage test (injecting an isotonic sodium chloride solution through the cystic duct) and the White test (injecting a fat emulsion solution through the cystic duct) were carried out in the same patients. The detection of bile leakage was compared between the conventional method and the White test. A bile leak was demonstrated in 8 patients (26.7%) by the conventional method and in 19 patients (63.3%) by the White test. In addition, the White test detected a significantly higher number of bile leakage sites compared with the conventional method (Wilcoxon signed-rank test; P < 0.001). The White test is better than the conventional test for the intraoperative detection of bile leakage. Based on our study, we recommend that surgeons investigating bile leakage sites during liver resections should use the White test instead of the conventional bile leakage test.

Interleaving subthalamic nucleus deep brain stimulation to avoid side effects while achieving satisfactory motor benefits in Parkinson disease: A report of 12 cases.

PubMed

Zhang, Shizhen; Zhou, Peizhi; Jiang, Shu; Wang, Wei; Li, Peng

2016-12-01

Deep brain stimulation (DBS) of the subthalamic nucleus is an effective treatment for advanced Parkinson disease (PD). However, achieving ideal outcomes by conventional programming can be difficult in some patients, resulting in suboptimal control of PD symptoms and stimulation-induced adverse effects. Interleaving stimulation (ILS) is a newer programming technique that can individually optimize the stimulation area, thereby improving control of PD symptoms while alleviating stimulation-induced side effects after conventional programming fails to achieve the desired results. We retrospectively reviewed PD patients who received DBS programming during the previous 4 years in our hospital. We collected clinical and demographic data from 12 patients who received ILS because of incomplete alleviation of PD symptoms or stimulation-induced adverse effects after conventional programming had proven ineffective or intolerable. Appropriate lead location was confirmed with postoperative reconstruction images. The rationale and clinical efficacy of ILS was analyzed. We divided our patients into 4 groups based on the following symptoms: stimulation-induced dysarthria and choreoathetoid dyskinesias, gait disturbance, and incomplete control of parkinsonism. After treatment with ILS, patients showed satisfactory improvement in PD symptoms and alleviation of stimulation-induced side effects, with a mean improvement in Unified PD Rating Scale motor scores of 26.9%. ILS is a newer choice and effective programming strategy to maximize symptom control in PD while decreasing stimulation-induced adverse effects when conventional programming fails to achieve satisfactory outcome. However, we should keep in mind that most DBS patients are routinely treated with conventional stimulation and that not all patients benefit from ILS. ILS is not recommended as the first choice of programming, and it is recommended only when patients have unsatisfactory control of PD symptoms or stimulation-induced side effects after multiple treatments with conventional stimulation. A return to conventional stimulation may be required if ILS induces new side effects or the needs of the patient change.

Interleaving subthalamic nucleus deep brain stimulation to avoid side effects while achieving satisfactory motor benefits in Parkinson disease

PubMed Central

Zhang, Shizhen; Zhou, Peizhi; Jiang, Shu; Wang, Wei; Li, Peng

2016-01-01

Abstract Background: Deep brain stimulation (DBS) of the subthalamic nucleus is an effective treatment for advanced Parkinson disease (PD). However, achieving ideal outcomes by conventional programming can be difficult in some patients, resulting in suboptimal control of PD symptoms and stimulation-induced adverse effects. Interleaving stimulation (ILS) is a newer programming technique that can individually optimize the stimulation area, thereby improving control of PD symptoms while alleviating stimulation-induced side effects after conventional programming fails to achieve the desired results. Methods: We retrospectively reviewed PD patients who received DBS programming during the previous 4 years in our hospital. We collected clinical and demographic data from 12 patients who received ILS because of incomplete alleviation of PD symptoms or stimulation-induced adverse effects after conventional programming had proven ineffective or intolerable. Appropriate lead location was confirmed with postoperative reconstruction images. The rationale and clinical efficacy of ILS was analyzed. Results: We divided our patients into 4 groups based on the following symptoms: stimulation-induced dysarthria and choreoathetoid dyskinesias, gait disturbance, and incomplete control of parkinsonism. After treatment with ILS, patients showed satisfactory improvement in PD symptoms and alleviation of stimulation-induced side effects, with a mean improvement in Unified PD Rating Scale motor scores of 26.9%. Conclusions: ILS is a newer choice and effective programming strategy to maximize symptom control in PD while decreasing stimulation-induced adverse effects when conventional programming fails to achieve satisfactory outcome. However, we should keep in mind that most DBS patients are routinely treated with conventional stimulation and that not all patients benefit from ILS. ILS is not recommended as the first choice of programming, and it is recommended only when patients have unsatisfactory control of PD symptoms or stimulation-induced side effects after multiple treatments with conventional stimulation. A return to conventional stimulation may be required if ILS induces new side effects or the needs of the patient change. PMID:27930569

World Trade Organization, ILO conventions, and workers' compensation.

PubMed

LaDou, Joseph

2005-01-01

The World Trade Organization, the World Bank, and the International Monetary Fund can assist in the implementation of ILO Conventions relating to occupational safety and health in developing countries. Most countries that seek to trade globally receive permission to do so from the WTO. If the WTO required member countries to accept the core ILO Conventions relating to occupational safety and health and workers' compensation, it could accomplish something that has eluded international organizations for decades. International workers' compensation standards are seldom discussed, but may at this time be feasible. Acceptance of a minimum workers' compensation insurance system could be a requirement imposed on applicant nations by WTO member states.

Snow in Time for the Solstice

NASA Technical Reports Server (NTRS)

2004-01-01

In mid-December, the weather in eastern North America cooperated with the calendar, and a wintry blast from the Arctic delivered freezing cold air, blustery winds, and snow just in time for the Winter Solstice on December 21' the Northern Hemisphere's longest night of the year and the official start of winter. This image was captured by the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) on December 20, 2004, the day after an Arctic storm dove down into the United States, bringing snow to New England (upper right of top image); the coastal mid-Atlantic, including Washington, D.C.; and the southern Appalachian Mountains in Tennessee and North Carolina. Over the Atlantic Ocean (image right), the fierce Arctic winds were raking the clouds into rows, like a gardener getting ready to plant the seeds of winter. The detailed close-up at the bottom of this image pair shows the cloud and snow patterns around Lake Ontario, illustrating the occurrence of 'lake-effect snow.' Areas in western upstate New York often get as much as fifteen feet or more of snow each year as cold air from Canada and the Arctic sweeps down over the relatively warm waters of Lakes Ontario and Erie. Cold air plus moisture from the lakes equals heavy snow. Since the wind generally blows from west to east, it is the 'downwind' cities like Buffalo and Rochester that receive the heaping helpings of snowfall, while cities on the upwind side of the lake, such as Toronto, receive much less. Unlike storms that begin with specific low-pressure systems in the Pacific Ocean and march eastward across the Pacific Northwest, the Rockies, the Great Plains, and sometimes the East, the lake-effect snows aren't tied to a specific atmospheric disturbance. They are more a function of geography, which means that the lakes can keep fueling snow storms for as long as they remain ice-free in early winter, as well as when they begin to thaw in late winter and early spring. Image courtesy the SeaWiFS Project, NASA/Goddard Space Flight Center, and ORBIMAGE.

Managing cardiac arrest with refractory ventricular fibrillation in the emergency department: Conventional cardiopulmonary resuscitation versus extracorporeal cardiopulmonary resuscitation.

PubMed

Siao, Fu-Yuan; Chiu, Chun-Chieh; Chiu, Chun-Wen; Chen, Ying-Chen; Chen, Yao-Li; Hsieh, Yung-Kun; Lee, Chien-Hui; Wu, Chang-Te; Chou, Chu-Chung; Yen, Hsu-Heng

2015-07-01

Refractory ventricular fibrillation, resistant to conventional cardiopulmonary resuscitation (CPR), is a life threatening rhythm encountered in the emergency department. Although previous reports suggest the use of extracorporeal CPR can improve the clinical outcomes in patients with prolonged cardiac arrest, the effectiveness of this novel strategy for refractory ventricular fibrillation is not known. We aimed to compare the clinical outcomes of patients with refractory ventricular fibrillation managed with conventional CPR or extracorporeal CPR in our institution. This is a retrospective chart review study from an emergency department in a tertiary referral medical center. We identified 209 patients presenting with cardiac arrest due to ventricular fibrillation between September 2011 and September 2013. Of these, 60 patients were enrolled with ventricular fibrillation refractory to resuscitation for more than 10 min. The clinical outcome of patients with ventricular fibrillation received either conventional CPR, including defibrillation, chest compression, and resuscitative medication (C-CPR, n = 40) or CPR plus extracorporeal CPR (E-CPR, n = 20) were compared. The overall survival rate was 35%, and 18.3% of patients were discharged with good neurological function. The mean duration of CPR was longer in the E-CPR group than in the C-CPR group (69.90 ± 49.6 min vs 34.3 ± 17.7 min, p = 0.0001). Patients receiving E-CPR had significantly higher rates of sustained return of spontaneous circulation (95.0% vs 47.5%, p = 0.0009), and good neurological function at discharge (40.0% vs 7.5%, p = 0.0067). The survival rate in the E-CPR group was higher (50% vs 27.5%, p = 0.1512) at discharge and (50% vs 20%, p = 0. 0998) at 1 year after discharge. The management of refractory ventricular fibrillation in the emergency department remains challenging, as evidenced by an overall survival rate of 35% in this study. Patients with refractory ventricular fibrillation receiving E-CPR had a trend toward higher survival rates and significantly improved neurological outcomes than those receiving C-CPR. Copyright © 2015 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Secondary leukemia associated with a conventional dose of etoposide: review of serial germ cell tumor protocols.

PubMed

Nichols, C R; Breeden, E S; Loehrer, P J; Williams, S D; Einhorn, L H

1993-01-06

Case reports have suggested that treatment with high-dose etoposide can result in development of a unique secondary leukemia. This study was designed to estimate the risk of developing leukemia for patients receiving conventional doses of etoposide along with cisplatin and bleomycin. We reviewed the records at Indiana University of all untreated patients entering clinical trials using etoposide at conventional doses (cumulative dose, 2000 mg/m2 or less) for germ cell cancer between 1982 and 1991. The records of all patients who received a chemotherapy regimen containing etoposide, ifosfamide, or cisplatin after failing to respond to primary chemotherapy were also reviewed. Between 1982 and 1991, 538 patients entered serial clinical trials with planned cumulative etoposide doses of 1500-2000 mg/m2 in combination with cisplatin plus either ifosfamide or bleomycin. Of these 538 patients, 348 received an etoposide combination as initial chemotherapy and 190 received etoposide as part of salvage treatment. To date, 315 patients are alive, with median follow-up of 4.9 years, and 337 patients have had follow-up beyond 2 years. Two patients (0.37%) developed leukemia. One developed acute undifferentiated leukemia with a t(4;11) (q21;q23) cytogenetic abnormality 2.0 years after starting etoposide-based therapy, and one developed acute myelomonoblastic leukemia with no chromosome abnormalities 2.3 years after beginning chemotherapy. During this period, several hundred patients were treated with etoposide-based chemotherapy and did not enter clinical trials. Three of these patients are known to have developed hematologic abnormalities, including one patient with acute monoblastic leukemia with a t(11;19)(q13;p13) abnormality. Secondary leukemia after treatment with a conventional dose of etoposide does occur, but the low incidence does not alter the risk-to-benefit ratio of etoposide-based chemotherapy in germ cell cancer. The reports of leukemia associated with high doses of etoposide emphasize the need for diligent follow-up of patients and make careful risk-to-benefit analysis imperative.

Clinical Outcomes of a Pneumatic Unloader Brace for Kellgren-Lawrence Grades 3 to 4 Osteoarthritis: A Minimum 1-Year Follow-Up Study.

PubMed

Chughtai, Morad; Bhave, Anil; Khan, Sabahat Z; Khlopas, Anton; Ali, Osman; Harwin, Steven F; Mont, Michael A

2016-11-01

The use of a pneumatic unloader brace has been shown in pilot studies to decrease pain and increase muscle strength in patients with knee osteoarthritis (OA). Therefore, we analyzed patients who had knee OA, and either received a pneumatic unloader brace and conventional treatment or conventional treatment alone. Specifically, we assessed: (1) use of pain relieving injections; (2) opioid consumption; and (3) the eventual need for total knee arthroplasty (TKA) in the above-mentioned cohort. We performed an analysis of a longitudinally maintained database of patients from a prospective, randomized, single center study. This study randomized patients who had Kellgren-Lawrence grades 3 to 4 to receive either a pneumatic unloader brace and conventional treatment or conventional treatment alone. The brace cohort comprised 11 patients with a mean age of 55 years (range, 37-70 years). The final matched cohort comprised 25 patients with a mean age of 63 years (range, 41-86 years). The minimum follow-up was 1 year. There was a lower proportion of patients who underwent an eventual TKA in the bracing cohort as compared with the nonbracing cohort (18 vs. 36%). The mean time to TKA was longer in the bracing cohort as compared with the nonbracing cohort (482 vs. 389 days). The proportion of patients who used opioids was similar in both groups (27 vs. 22%). There was a significantly lower number of patients who received injections in the bracing cohort as compared with the nonbracing cohort (46 vs. 83%, p  = 0.026). The bracing cohort had received a significantly lower number of injections and a lower rate of subsequent TKA as compared with the nonbracing cohort. The mean time to TKA was also longer among the bracing cohort. These results may demonstrate the potential of this brace to reduce the need for and prolonging the time to TKA. Performing larger prospective randomized studies, with built-in compliance monitors is warranted. This brace may be a valuable adjunct to the current knee OA treatment armamentarium pending further investigation. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Techno-economic assessment of a hybrid solar receiver and combustor

NASA Astrophysics Data System (ADS)

Lim, Jin Han; Nathan, Graham; Dally, Bassam; Chinnici, Alfonso

2016-05-01

A techno-economic analysis is performed to compare two different configurations of hybrid solar thermal systems with fossil fuel backup to provide continuous electricity output. The assessment compares a Hybrid Solar Receiver Combustor (HSRC), in which the functions of a solar cavity receiver and a combustor are integrated into a single device with a reference conventional solar thermal system using a regular solar cavity receiver with a backup boiler, termed the Solar Gas Hybrid (SGH). The benefits of the integration is assessed by varying the size of the storage capacity and heliostat field while maintaining the same overall thermal input to the power block.

Random noise attenuation of non-uniformly sampled 3D seismic data along two spatial coordinates using non-equispaced curvelet transform

NASA Astrophysics Data System (ADS)

Zhang, Hua; Yang, Hui; Li, Hongxing; Huang, Guangnan; Ding, Zheyi

2018-04-01

The attenuation of random noise is important for improving the signal to noise ratio (SNR). However, the precondition for most conventional denoising methods is that the noisy data must be sampled on a uniform grid, making the conventional methods unsuitable for non-uniformly sampled data. In this paper, a denoising method capable of regularizing the noisy data from a non-uniform grid to a specified uniform grid is proposed. Firstly, the denoising method is performed for every time slice extracted from the 3D noisy data along the source and receiver directions, then the 2D non-equispaced fast Fourier transform (NFFT) is introduced in the conventional fast discrete curvelet transform (FDCT). The non-equispaced fast discrete curvelet transform (NFDCT) can be achieved based on the regularized inversion of an operator that links the uniformly sampled curvelet coefficients to the non-uniformly sampled noisy data. The uniform curvelet coefficients can be calculated by using the inversion algorithm of the spectral projected-gradient for ℓ1-norm problems. Then local threshold factors are chosen for the uniform curvelet coefficients for each decomposition scale, and effective curvelet coefficients are obtained respectively for each scale. Finally, the conventional inverse FDCT is applied to the effective curvelet coefficients. This completes the proposed 3D denoising method using the non-equispaced curvelet transform in the source-receiver domain. The examples for synthetic data and real data reveal the effectiveness of the proposed approach in applications to noise attenuation for non-uniformly sampled data compared with the conventional FDCT method and wavelet transformation.

Hearing evaluation of intratympanic methylprednisolone perfusion for refractory sudden sensorineural hearing loss.

PubMed

She, Wandong; Dai, Yanhong; Du, Xiaoping; Yu, Chenjie; Chen, Feng; Wang, Junguo; Qin, Xiaoming

2010-02-01

To investigate the effectiveness and safety of intratympanic methylprednisolone perfusion (IMP) through a microcatheter in patients with sudden sensorineural hearing loss (SSNHL) who failed a conventional treatment. Prospective clinical study. This study was conducted in Nanjing Drum Tower Hospital, Nanjing University Medical School. Patients who had failed a minimum 10-day conventional treatment were included. Twenty-six patients in the study group (SG) received methylprednisolone perfusion through a microcatheter placed into the tympanum once a day for 10 days and the conventional treatment. Twenty-three patients who received a second conventional treatment (no steroid) served as the comparison group (CG). All patients were followed up for three months after the end of treatment. The effective rates for SG and CG were 50 percent (61.9% when only patients with an interval from onset to IMP < or = 60 days were included) and 21.7 percent, respectively (chi(2) = 4.194, P = 0.041). The pure-tone average improvement was 20.2 +/- 15.6 dB in SG, and 9.2 +/- 13.7 dB in CG (z = 2.51, P = 0.011). In SG, hearing improvement at low frequencies was better than that at high frequencies. The interval from onset to IMP affected the efficacy of IMP. IMP through a microcatheter is a promising treatment for refractory SSNHL. The data suggest that the treatment may be more effective when administered at the earlier stages of SSNHL when the conventional treatment has failed. Copyright 2010 American Academy of Otolaryngology-Head and Neck Surgery Foundation. Published by Mosby, Inc. All rights reserved.

Quality of life after robotic thyroidectomy by a gasless unilateral axillary approach.

PubMed

Song, Chang Myeon; Ji, Yong Bae; Bang, Hyang Sook; Park, Chul Won; Kim, Dong Sun; Tae, Kyung

2014-12-01

Robotic thyroidectomies have been safely performed with early surgical outcomes comparable to conventional cervical thyroidectomies. However, health-related quality of life (HRQOL) after robotic thyroidectomy has not yet been evaluated. The aim of this study was to compare HRQOL of patients who underwent robotic thyroidectomy with that of those who received conventional thyroidectomy. We conducted a cross-sectional study in 111 patients who underwent either robotic thyroidectomy (44 patients) via a gasless unilateral axillary approach, or conventional cervical thyroidectomy (67 patients), for papillary thyroid carcinoma (PTC). HRQOL of patients was assessed using two questionnaires, the University of Washington Quality of Life (UW-QOL) questionnaire for patients with head and neck cancer, and the Quality of Life-Thyroid Version (QOL-TV), which was specifically designed for thyroid cancer patients. The survey using the questionnaires was performed 1 year after surgery at a routine outpatient clinic follow-up. There was no difference in UW-QOL scores between the two groups for any factor other than neck appearance and physical composite score, which were higher in the robotic group. Humor (mood) and anxiety, emotional measures of UW-QOL, were selected by patients in both groups as being their most significant issue during the preceding 7 days. There was no between-group difference in the four QOL-TV domains (physical, psychological, social, and spiritual well-being). Patients who underwent robotic thyroidectomy reported a higher score for satisfaction with neck appearance compared to patients receiving conventional cervical thyroidectomy. However, the overall HRQOL of patients in the robotic and conventional groups was similar.

The ultrasound-assisted physical examination in the periodic health evaluation of the elderly.

PubMed

Siepel, T; Clifford, D S; James, P A; Cowan, T M

2000-07-01

Except for specific procedures such as blood pressure measurement, the conventional physical examination (PE) does not have sufficient sensitivity to be useful as part of the periodic health evaluation. Ultrasound has demonstrated greater sensitivity and specificity in numerous studies but has been too expensive to be widely employed in health screening. The purpose of our study was to determine whether an examination in which conventional and ultrasound techniques are blended and applied by a primary care physician might be feasible and useful in the periodic health evaluations of senior citizens. Seventy-two patients presenting to a community-based family physician for periodic health evaluations received an ultrasound-assisted physical examination (USA-PE) from a second family physician. The results were reported to the primary physician, and the outcomes were tracked for periods of up to 2 years. Twenty-two of the 72 patients (31%) had abnormalities found by the USA-PE that were not apparent during the conventional PE. Five of these patients (7%) had serious conditions that received prompt treatment with apparent benefit. Findings included endometrial carcinoma, abdominal aortic aneurysm, carotid stenosis, hydronephrosis, and urinary retention. The USA-PE found more abnormalities in this group of patients than conventional PE. Whether it can improve outcomes for senior citizens undergoing periodic health evaluations in a cost-effective manner is yet to be determined.

Efficacy of an Electromechanical Gait Trainer Poststroke in Singapore: A Randomized Controlled Trial.

PubMed

Chua, Joyce; Culpan, Jane; Menon, Edward

2016-05-01

To evaluate the longer-term effects of electromechanical gait trainers (GTs) combined with conventional physiotherapy on health status, function, and ambulation in people with subacute stroke in comparison with conventional physiotherapy given alone. Randomized controlled trial with intention-to-treat analysis. Community hospital in Singapore. Nonambulant individuals (N=106) recruited approximately 1 month poststroke. Both groups received 45 minutes of physiotherapy 6 times per week for 8 weeks as follows: the GT group received 20 minutes of GT training and 5 minutes of stance/gait training in contrast with 25 minutes of stance/gait training for the control group. Both groups completed 10 minutes of standing and 10 minutes of cycling. The primary outcome was the Functional Ambulation Category (FAC). Secondary outcomes were the Barthel Index (BI), gait speed and endurance, and Stroke Impact Scale (SIS). Measures were taken at baseline and 4, 8, 12, 24, and 48 weeks. Generalized linear model analysis showed significant improvement over time (independent of group) for the FAC, BI, and SIS physical and participation subscales. However, no significant group × time or group differences were observed for any of the outcome variables after generalized linear model analysis. The use of GTs combined with conventional physiotherapy can be as effective as conventional physiotherapy applied alone for people with subacute stroke. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Integrating life skills into a theory-based drug-use prevention program: effectiveness among junior high students in Taiwan.

PubMed

Huang, Chiu-Mieh; Chien, Li-Yin; Cheng, Chin-Feng; Guo, Jong-Long

2012-07-01

Drug use has been noted among students in Taiwan during the past decade and schools have a role in preventing or delaying students' drug use. We developed and evaluated a school-based, drug-use prevention program integrating the theory of planned behavior (TPB) and life skills for junior high school students. We recruited 441 seventh graders from randomly selected schools: N = 143 experimental groups, N = 142 conventional groups, and N = 156 control groups. The experimental group received ten 45-minute sessions of theory-based interventions. The conventional group got traditional didactic teaching and drug refusal skills. The control group received no intervention. Compared to the control group, experimental group students showed greater improvement in attitude, subjective norm, perceived behavioral control, life skills, and intention not to use drugs. Compared to the conventional group, the experimental group had significantly higher posttest scores for 4 of the 5 outcomes, including life skills (96.53 vs. 90.92, p < .001), attitude (27.43 vs. 24.40, p = .012), subjective norm (29.51 vs. 28.06, p = .002), and perceived behavioral control (18.59 vs. 16.81, p < .001). The conventional group scored significantly higher in behavioral intention than did the control group. Study results demonstrated the effectiveness of a drug-use prevention program integrating the TPB and life skills. © 2012, American School Health Association.

Evaluation of a Self-Management Program for Gastroesophageal Reflux Disease in China.

PubMed

Xu, Wenhong; Sun, Changxian; Lin, Zheng; Lin, Lin; Wang, Meifeng; Zhang, Hongjie; Song, Yulei

2016-01-01

Gastroesophageal reflux disease is a chronic disease with a high incidence worldwide. The various symptoms have substantial impact on the quality of life of affected individuals. A long-term self-management program can increase the ability of patients to make behavioral changes, and health outcomes can improve as a consequence. This study's aim was to evaluate the effectiveness of a self-management program for gastroesophageal reflux disease. A total of 115 patients with gastroesophageal reflux disease were allocated to the experimental group and the control group. The former received self-management intervention along with conventional drug therapy, whereas the latter received standard outpatient care and conventional drug therapy. After the clinical trial, the control group also received the same self-management intervention. The levels of self-management behaviors, self-efficacy, gastroesophageal reflux disease symptoms, and psychological condition were compared. Those in the experimental group demonstrated significantly higher self-efficacy for managing their illness, showed positive changes in self-management behaviors, and had comparatively better remission of symptoms and improvement in psychological distress. The program helped patients with gastroesophageal reflux disease self-manage their illness as possible.

Evidence for the long term cost effectiveness of home care reablement programs.

PubMed

Lewin, Gill F; Alfonso, Helman S; Alan, Janine J

2013-01-01

The objectives of this study were to determine whether older individuals who participated in a reablement (restorative) program rather than immediately receiving conventional home care services had a reduced need for ongoing support and lower home care costs over the next 57 months (nearly 5 years). Data linkage was used to examine retrospectively the service records of older individuals who had received a reablement service versus a conventional home care service to ascertain their use of home care services over time. Individuals who had received a reablement service were less likely to use a personal care service throughout the follow-up period or any other type of home care over the next 3 years. This reduced use of home care services was associated with median cost savings per person of approximately AU $12,500 over nearly 5 years. The inclusion of reablement as the starting point for individuals referred for home care within Australia's reformed aged care system could increase the system's cost effectiveness and ensure that all older Australians have the opportunity to maximize their independence as they age.

Ultrasonic imaging using optoelectronic transmitters.

PubMed

Emery, C D; Casey, H C; Smith, S W

1998-04-01

Conventional ultrasound scanners utilize electronic transmitters and receivers at the scanner with a separate coaxial cable connected to each transducer element in the handle. The number of transducer elements determines the size and weight of the transducer cable assembly that connects the imaging array to the scanner. 2-D arrays that allow new imaging modalities to be introduced significantly increase the channel count making the transducer cable assembly more difficult to handle. Therefore, reducing the size and increasing the flexibility of the transducer cable assembly is a concern. Fiber optics can be used to transmit signals optically and has distinct advantages over standard coaxial cable to increase flexibility and decrease the weight of the transducer cable for larger channel numbers. The use of fiber optics to connect the array and the scanner entails the use of optoelectronics such as detectors and laser diodes to send and receive signals. In transmit, optoelectronics would have to be designed to produce high-voltage wide-bandwidth pulses across the transducer element. In this paper, we describe a 48 channel ultrasound system having 16 optoelectronic transmitters and 32 conventional electronic receivers. We investigated both silicon avalanche photodiodes (APD's) and GaAs lateral photoconductive semiconductor switches (PCSS's) for producing the transmit pulses. A Siemens SI-1200 scanner and a 2.25 MHz linear array were used to compare the optoelectronic system to a conventional electronic transmit system. Transmit signal results and images in tissue mimicking of cysts and tumors are provided for comparison.

Effectiveness of conventional versus virtual reality-based balance exercises in vestibular rehabilitation for unilateral peripheral vestibular loss: results of a randomized controlled trial.

PubMed

Meldrum, Dara; Herdman, Susan; Vance, Roisin; Murray, Deirdre; Malone, Kareena; Duffy, Douglas; Glennon, Aine; McConn-Walsh, Rory

2015-07-01

To compare the effectiveness of virtual reality-based balance exercises to conventional balance exercises during vestibular rehabilitation in patients with unilateral peripheral vestibular loss (UVL). Assessor-blind, randomized controlled trial. Two acute care university teaching hospitals. Patients with UVL (N=71) who had dizziness/vertigo, and gait and balance impairment. Patients with UVL were randomly assigned to receive 6 weeks of either conventional (n=36) or virtual reality-based (n=35) balance exercises during vestibular rehabilitation. The virtual reality-based group received an off-the-shelf virtual reality gaming system for home exercise, and the conventional group received a foam balance mat. Treatment comprised weekly visits to a physiotherapist and a daily home exercise program. The primary outcome was self-preferred gait speed. Secondary outcomes included other gait parameters and tasks, Sensory Organization Test (SOT), dynamic visual acuity, Hospital Anxiety and Depression Scale, Vestibular Rehabilitation Benefits Questionnaire, and Activities Balance Confidence Questionnaire. The subjective experience of vestibular rehabilitation was measured with a questionnaire. Both groups improved, but there were no significant differences in gait speed between the groups postintervention (mean difference, -.03m/s; 95% confidence interval [CI], -.09 to .02m/s). There were also no significant differences between the groups in SOT scores (mean difference, .82%; 95% CI, -5.00% to 6.63%) or on any of the other secondary outcomes (P>.05). In both groups, adherence to exercise was high (∼77%), but the virtual reality-based group reported significantly more enjoyment (P=.001), less difficulty with (P=.009) and less tiredness after (P=.03) balance exercises. At 6 months, there were no significant between-group differences in physical outcomes. Virtual reality-based balance exercises performed during vestibular rehabilitation were not superior to conventional balance exercises during vestibular rehabilitation but may provide a more enjoyable method of retraining balance after unilateral peripheral vestibular loss. Copyright © 2015 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Randomized Controlled Double-blind Trial Comparing Haloperidol Combined With Conventional Therapy to Conventional Therapy Alone in Patients With Symptomatic Gastroparesis.

PubMed

Roldan, Carlos J; Chambers, Kimberly A; Paniagua, Linda; Patel, Sonali; Cardenas-Turanzas, Marylou; Chathampally, Yashwant

2017-11-01

Gastroparesis is a debilitating condition that causes nausea, vomiting, and abdominal pain. Management includes analgesics and antiemetics, but symptoms are often refractory. Haloperidol has been utilized in the palliative care setting for similar symptoms. The study objective was to determine whether haloperidol as an adjunct to conventional therapy would improve symptoms in gastroparesis patients presenting to the emergency department (ED). This was a randomized, double-blind, placebo-controlled trial of adult ED patients with acute exacerbation of previously diagnosed gastroparesis. The treatment group received 5 mg of haloperidol plus conventional therapy (determined by the treating physician). The control group received a placebo plus conventional therapy. The severity of each subject's abdominal pain and nausea were assessed before intervention and every 15 minutes thereafter for 1 hour using a 10-point scale for pain and a 5-point scale for nausea. Primary outcomes were decreased pain and nausea 1 hour after treatment. Of the 33 study patients, 15 were randomized to receive haloperidol. Before treatment, the mean intensity of pain was 8.5 in the haloperidol group and 8.28 in the placebo group; mean pretreatment nausea scores were 4.53 and 4.11, respectively. One hour after therapy, the mean pain and nausea scores in the haloperidol group were 3.13 and 1.83 compared to 7.17 and 3.39 in the placebo group. The reduction in mean pain intensity therapy was 5.37 in the haloperidol group (p ≤ 0.001) compared to 1.11 in the placebo group (p = 0.11). The reduction in mean nausea score was 2.70 in the haloperidol group (p ≤ 0.001) and 0.72 in the placebo group (p = 0.05). Therefore, the reductions in symptom scores were statistically significant in the haloperidol group but not in the placebo group. No adverse events were reported. Haloperidol as an adjunctive therapy is superior to placebo for acute gastroparesis symptoms. © 2017 by the Society for Academic Emergency Medicine.

Non-Kinetic Capabilities for Irregular Warfare: Four Case Studies

DTIC Science & Technology

2009-03-01

on the job, absenteeism , receiving free “perks”) 2. “Conventional” Corruption—Something is done or not done for some reward (bribery, kickbacks...occupational deviance that breaks departmental rules and regulations, such as sleeping on the job, absenteeism , and receiving free “perks.” “Conventional...African Security Review, Vol. 7, No. 1, 1998. Tanzi, Vito, “Corruption Around the World: Causes, Consequences, Scope, and Cures ,” IMF Staff Papers

Receiver System: Lessons Learned from Solar Two

NASA Astrophysics Data System (ADS)

Litwin, R. Z.

2002-03-01

The Boeing Company fabricated the Solar Two receiver as a subcontractor for the Solar Two project. The receiver absorbed sunlight reflected from the heliostat field. A molten-nitrate-salt heat transfer fluid was pumped from a storage tank at grade level, heated from 290 to 565DGC by the receiver mounted on top of a tower, then flowed back down into another storage tank. To make electricity, the hot salt was pumped through a steam generator to produce steam that powered a conventional Rankine steam turbine/generator. This evaluation identifies the most significant Solar Two receiver system lessons learned from the Mechanical Design, Instrumentation and Control, Panel Fabrication, Site Construction, Receiver System Operation, and Management from the perspective of the receiver designer/manufacturer. The lessons learned on the receiver system described here consist of two parts: the Problem and one or more identified Solutions. The appendix summarizes an inspection of the advanced receiver panel developed by Boeing that was installed and operated in the Solar Two receiver.

Receiver System: Lessons Learned From Solar Two

DOE Office of Scientific and Technical Information (OSTI.GOV)

LITWIN, ROBERT Z.; PACHECO, JAMES E.

The Boeing Company fabricated the Solar Two receiver as a subcontractor for the Solar Two project. The receiver absorbed sunlight reflected from the heliostat field. A molten-nitrate-salt heat transfer fluid was pumped from a storage tank at grade level, heated from 290 to 565 C by the receiver mounted on top of a tower, then flowed back down into another storage tank. To make electricity, the hot salt was pumped through a steam generator to produce steam that powered a conventional Rankine steam turbine/generator. This evaluation identifies the most significant Solar Two receiver system lessons learned from the Mechanical Design,more » Instrumentation and Control, Panel Fabrication, Site Construction, Receiver System Operation, and Management from the perspective of the receiver designer/manufacturer. The lessons learned on the receiver system described here consist of two parts: the Problem and one or more identified Solutions. The appendix summarizes an inspection of the advanced receiver panel developed by Boeing that was installed and operated in the Solar Two receiver.« less

CD20 positivity and white blood cell count predict treatment outcomes in Philadelphia chromosome-negative acute lymphoblastic leukemia patients ineligible for pediatric-inspired chemotherapy.

PubMed

Isshiki, Yusuke; Ohwada, Chikako; Sakaida, Emiko; Onoda, Masahiro; Aotsuka, Nobuyuki; Tanaka, Hiroaki; Fukazawa, Motoharu; Cho, Ryuko; Sugawara, Takeaki; Kawaguchi, Takeharu; Hara, Satoru; Yokota, Akira

2017-11-01

The efficacy of conventional chemotherapy and allogeneic hematopoietic stem cell transplantation (allo-HSCT) has been controversial as post-remission therapies for adult Philadelphia chromosome-negative acute lymphoblastic leukemia patients. We retrospectively analyzed 96 adolescent and adult cases of Philadelphia chromosome-negative acute lymphoblastic leukemia to evaluate whether allo-HSCT should be performed after first complete remission (1CR). In total, 34 patients received chemotherapy followed by allo-HSCT (HSCT group) and 62 received chemotherapy alone (chemotherapy group). No significant differences in the event-free survival (EFS) or overall survival were observed between the two groups. In the chemotherapy group, use of pediatric regimens was significantly associated with favorable EFS, while high white blood cell (WBC) count and CD20 positivity were associated with poor outcome. In patients who received pediatric regimens, subsequent allo-HSCT did not influence EFS. In patients who received conventional chemotherapy (adult regimen), subsequent allo-HSCT did not improve EFS. High WBC count and CD20 positivity were also significantly associated with poor EFS in patients who received adult regimens. Patients with low WBC count and absence of CD20 who received adult regimens did not benefit from allo-HSCT. Allo-HSCT may not be required in the pediatric regimen-eligible patients; however, pediatric regimen-ineligible patients with either CD20 positivity or high WBC count should receive allo-HSCT after achieving 1CR. This study was registered at http://www.umin.ac.jp/ctr/ as #C000016287. © The Author 2017. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Effectiveness of dental checkups incorporating tooth brushing instruction.

PubMed

Furusawa, Masahiro; Takahashi, Jun-ichi; Isoyama, Motoko; Kitamura, Yoshiko; Kashima, Tomoko; Ueshima, Fumie; Nakahama, Noriko; Araki, Misako; Rokukawa, Yasuko; Takahashi, Yoshikazu; Makiishi, Takemi; Yatabe, Ken-ichi

2011-01-01

The purpose of this study was to compare the effectiveness of dental checkups incorporating tooth-brushing instruction (TBI) with that of conventional dental checkups. A team consisting of one dentist and three dental hygienists saw an average of 60 employees per day on-site at an airline company. The patient's teeth were stained with a disclosing tablet and the results recorded on a Plaque Control Record (PCR) chart. The patient was then given TBI. After recording the relevant data, including TBI given and PCR scores, the charts were stored. Checkups were performed in a total of 3,854 patients between 2001 and 2005 and changes in annual scores investigated. In addition, annual shifts in mean score in patients receiving checkups over all five years were compared with those in patients receiving checkups for the first time in each of the five years. The mean score in patients receiving a checkup in 2001 was 35.1%, declining by 2.6 points to 32.5% in 2005. Among patients receiving checkups over all five years, the mean score in 2001 was 34.0%, declining by 11.2 points to 22.8% in 2005. Over the five-year period, the mean score in patients receiving checkups was 34.1%. In patients receiving checkups over all five years, the proportion with PCR scores <30% increased each year. This was because the number of patients with PCR scores ≥60% decreased each year. These findings suggest that TBI is effective in reducing poor plaque control. When compared with in patients who had not received TBI, five consecutive years of checkups was clearly effective. These results indicate that checkups incorporating TBI are more effective than conventional dental checkups that simply check for caries. In future, this type of checkup should contribute to improved preventative dentistry with minimal intervention.

On The Computation Of The Best-fit Okada-type Tsunami Source

NASA Astrophysics Data System (ADS)

Miranda, J. M. A.; Luis, J. M. F.; Baptista, M. A.

2017-12-01

The forward simulation of earthquake-induced tsunamis usually assumes that the initial sea surface elevation mimics the co-seismic deformation of the ocean bottom described by a simple "Okada-type" source (rectangular fault with constant slip in a homogeneous elastic half space). This approach is highly effective, in particular in far-field conditions. With this assumption, and a given set of tsunami waveforms recorded by deep sea pressure sensors and (or) coastal tide stations it is possible to deduce the set of parameters of the Okada-type solution that best fits a set of sea level observations. To do this, we build a "space of possible tsunami sources-solution space". Each solution consists of a combination of parameters: earthquake magnitude, length, width, slip, depth and angles - strike, rake, and dip. To constrain the number of possible solutions we use the earthquake parameters defined by seismology and establish a range of possible values for each parameter. We select the "best Okada source" by comparison of the results of direct tsunami modeling using the solution space of tsunami sources. However, direct tsunami modeling is a time-consuming process for the whole solution space. To overcome this problem, we use a precomputed database of Empirical Green Functions to compute the tsunami waveforms resulting from unit water sources and search which one best matches the observations. In this study, we use as a test case the Solomon Islands tsunami of 6 February 2013 caused by a magnitude 8.0 earthquake. The "best Okada" source is the solution that best matches the tsunami recorded at six DART stations in the area. We discuss the differences between the initial seismic solution and the final one obtained from tsunami data This publication received funding of FCT-project UID/GEO/50019/2013-Instituto Dom Luiz.

Gonzalez Regimen (PDQ)

MedlinePlus

... were more active than the rats in the control group , which did not receive the enzyme. Have any ... was how well patients in the Gonzalez regimen group actually followed the ... or control or cure disease. Unlike conventional treatments for cancer, ...

An Experimental Study of Turbulent Skin Friction Reduction in Supersonic Flow Using a Microblowing Technique

NASA Technical Reports Server (NTRS)

Hwang, Danny P.

1999-01-01

A new turbulent skin friction reduction technology, called the microblowing technique has been tested in supersonic flow (Mach number of 1.9) on specially designed porous plates with microholes. The skin friction was measured directly by a force balance and the boundary layer development was measured by a total pressure rake at the tailing edge of a test plate. The free stream Reynolds number was 1.0(10 exp 6) per meter. The turbulent skin friction coefficient ratios (C(sub f)/C(sub f0)) of seven porous plates are given in this report. Test results showed that the microblowing technique could reduce the turbulent skin friction in supersonic flow (up to 90 percent below a solid flat plate value, which was even greater than in subsonic flow).

A numerical study of hypersonic stagnation heat transfer predictions at a coordinate singularity

NASA Technical Reports Server (NTRS)

Grasso, Francesco; Gnoffo, Peter A.

1990-01-01

The problem of grid induced errors associated with a coordinate singularity on heating predictions in the stagnation region of a three-dimensional body in hypersonic flow is examined. The test problem is for Mach 10 flow over an Aeroassist Flight Experiment configuration. This configuration is composed of an elliptic nose, a raked elliptic cone, and a circular shoulder. Irregularities in the heating predictions in the vicinity of the coordinate singularity, located at the axis of the elliptic nose near the stagnation point, are examined with respect to grid refinement and grid restructuring. The algorithm is derived using a finite-volume formulation. An upwind-biased total-variation diminishing scheme is employed for the inviscid flux contribution, and central differences are used for the viscous terms.

Calculation of skiving cutter blade

NASA Astrophysics Data System (ADS)

Xu, Lei; Lao, Qicheng; Shang, Zhiyi

2018-05-01

The gear skiving method is a kind of gear machining technology with high efficiency and high precision. According to the method of gear machining, a method for calculating the blade of skiving cutter in machining an involute gear is proposed. Based on the principle of meshing gear and the kinematic relationship between the machined flank and the gear skiving, the mathematical model of skiving for machining the internal gear is built and the gear tooth surface is obtained by solving the meshing equation. The mathematical model of the gear blade curve of the skiving cutter is obtained by choosing the proper rake face and the cutter tooth surface for intersection. Through the analysis of the simulation of the skiving gear, the feasibility and correctness of the skiving cutter blade design are verified.

Experimental wake survey behind a 140 deg-included-angle cone at angles of attack of 0 deg and 5 deg, Mach numbers from 1.60 to 3.95, and longitudinal stations varying from 1.0 to 8.39 body diameters

NASA Technical Reports Server (NTRS)

Brown, C. A., Jr.; Campbell, J. F.

1971-01-01

The flow properties in the wake of a 140 deg-included-angle cone at Mach numbers from 1.60 to 3.95 and at angles of attack of 0 deg and 5 deg are discussed. The wake flow properties are calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.0 to 8.39 body diameters and at lateral stations varying from -0.42 to 3.0 body diameters. These measurements show a consistent trend throughout the range of Mach number and longitudinal distance and an increase in dynamic pressure with increasing longitudinal station.

Experimental wake survey behind Viking 1975 entry vehicle at angles of attack of 0 deg and 5 deg, Mach numbers from 1.60 to 3.95, and longitudinal stations from 1.0 to 8.39 body diameters

NASA Technical Reports Server (NTRS)

Brown, C. A., Jr.; Campbell, J. F.; Tudor, D. H.

1971-01-01

An investigation was conducted to obtain flow properties in the wake of the Viking '75 entry vehicle at Mach numbers from 1.60 to 3.95 and at angles of attack of 0 deg and 5 deg. The wake flow properties were calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.0 to 8.39 body diameters and lateral stations varying from -0.42 to 3.0 body diameters. These measurements showed a a consistent trend throughout the range of Mach numbers and longitudinal distances and an increase in dynamic pressure with increasing downstream position.

High Accuracy Temperature Measurements Using RTDs with Current Loop Conditioning

NASA Technical Reports Server (NTRS)

Hill, Gerald M.

1997-01-01

To measure temperatures with a greater degree of accuracy than is possible with thermocouples, RTDs (Resistive Temperature Detectors) are typically used. Calibration standards use specialized high precision RTD probes with accuracies approaching 0.001 F. These are extremely delicate devices, and far too costly to be used in test facility instrumentation. Less costly sensors which are designed for aeronautical wind tunnel testing are available and can be readily adapted to probes, rakes, and test rigs. With proper signal conditioning of the sensor, temperature accuracies of 0.1 F is obtainable. For reasons that will be explored in this paper, the Anderson current loop is the preferred method used for signal conditioning. This scheme has been used in NASA Lewis Research Center's 9 x 15 Low Speed Wind Tunnel, and is detailed.

Long-term survival after sporadic and delayed metastases of conventional osteosarcoma

PubMed Central

Kubo, Tadahiko; Furuta, Taisuke; Johan, Muhammad P.; Yoshizuka, Masaaki; Ochi, Mitsuo; Adachi, Nobuo

2017-01-01

Abstract Histologically conventional osteosarcoma, once metastasized to the lung, generally causes a rapid and fatal outcome. Osteosarcoma metastasis to the gastrointestinal tract is extremely rare. We report herein a case of osteoblastic osteosarcoma with exceptionally unique features: sporadic lung metastases and delayed metastases to the stomach and the jejunum with long-term survival. She received multiple operations and chemotherapies, but consequently died of peritoneal dissemination. A review of the literature on osteosarcoma metastasis to the gastrointestinal tract is presented. This patient was very unusual in terms of a long-term survival and metastatic sites, suggesting the importance of vigilance and thorough follow-up for patients with conventional osteosarcoma. PMID:28471986

Frequency-noise cancellation in semiconductor lasers by nonlinear heterodyne detection.

PubMed

Bondurant, R S; Welford, D; Alexander, S B; Chan, V W

1986-12-01

The bit-error-rate (BER) performance of conventional noncoherent, heterodyne frequency-shift-keyed (FSK) optical communications systems can be surpassed by the use of a differential FSK modulation format and nonlinear postdetection processing at the receiver. A BER floor exists for conventional frequency-shift keying because of the frequency noise of the transmitter and local oscillator. The use of differential frequency-shift keying with nonlinear postdetection processing suppresses this BER floor for the semiconductor laser system considered here.

UWB communication receiver feedback loop

DOEpatents

Spiridon, Alex; Benzel, Dave; Dowla, Farid U.; Nekoogar, Faranak; Rosenbury, Erwin T.

2007-12-04

A novel technique and structure that maximizes the extraction of information from reference pulses for UWB-TR receivers is introduced. The scheme efficiently processes an incoming signal to suppress different types of UWB as well as non-UWB interference prior to signal detection. Such a method and system adds a feedback loop mechanism to enhance the signal-to-noise ratio of reference pulses in a conventional TR receiver. Moreover, sampling the second order statistical function such as, for example, the autocorrelation function (ACF) of the received signal and matching it to the ACF samples of the original pulses for each transmitted bit provides a more robust UWB communications method and system in the presence of channel distortions.

Dynamic Transmit-Receive Beamforming by Spatial Matched Filtering for Ultrasound Imaging with Plane Wave Transmission.

PubMed

Chen, Yuling; Lou, Yang; Yen, Jesse

2017-07-01

During conventional ultrasound imaging, the need for multiple transmissions for one image and the time of flight for a desired imaging depth limit the frame rate of the system. Using a single plane wave pulse during each transmission followed by parallel receive processing allows for high frame rate imaging. However, image quality is degraded because of the lack of transmit focusing. Beamforming by spatial matched filtering (SMF) is a promising method which focuses ultrasonic energy using spatial filters constructed from the transmit-receive impulse response of the system. Studies by other researchers have shown that SMF beamforming can provide dynamic transmit-receive focusing throughout the field of view. In this paper, we apply SMF beamforming to plane wave transmissions (PWTs) to achieve both dynamic transmit-receive focusing at all imaging depths and high imaging frame rate (>5000 frames per second). We demonstrated the capability of the combined method (PWT + SMF) of achieving two-way focusing mathematically through analysis based on the narrowband Rayleigh-Sommerfeld diffraction theory. Moreover, the broadband performance of PWT + SMF was quantified in terms of lateral resolution and contrast from both computer simulations and experimental data. Results were compared between SMF beamforming and conventional delay-and-sum (DAS) beamforming in both simulations and experiments. At an imaging depth of 40 mm, simulation results showed a 29% lateral resolution improvement and a 160% contrast improvement with PWT + SMF. These improvements were 17% and 48% for experimental data with noise.

Extended hours hemodialysis and survival: extended hours, extended evidence?

PubMed

Wald, Ron; Perl, Jeffrey

2016-12-01

Extended-hours hemodialysis presents another approach to the intensification of therapy for maintenance hemodialysis recipients. Smaller studies have demonstrated several potential benefits with this modality, but the impact on patient-centered outcomes has been unclear. We review the largest published study to compare survival among patients who received extended-hours hemodialysis with those who received conventional hemodialysis. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

BMDO Technology Applications in Biomedicine

DTIC Science & Technology

1996-01-01

capacitance and low- noise detectors. NOVA’s systems could also be used for bone densitometry and panoramic dental X-rays. Potential Use to Medicine Dr...receiver coils, increasing signal-to- noise ratio by a factor of two in some cases. This change is especially important in low-strength MRI fields...ongoing in this area. Receivers for this technology must be even more sensitive than for conventional MRI, because the " noise " level in these tissue

Cost-Benefit Analysis for ECIA Chapter 1 and State DPPF Programs Comparing Groups Receiving Regular Program Instruction and Groups Receiving Computer Assisted Instruction/Computer Management System (CAI/CMS). 1986-87.

ERIC Educational Resources Information Center

Chamberlain, Ed

A cost benefit study was conducted to determine the effectiveness of a computer assisted instruction/computer management system (CAI/CMS) as an alternative to conventional methods of teaching reading within Chapter 1 and DPPF funded programs of the Columbus (Ohio) Public Schools. The Chapter 1 funded Compensatory Language Experiences and Reading…

Solar power satellite system definition study. Volume 4: Solid State SPS Analysis, Phase 3

NASA Technical Reports Server (NTRS)

1980-01-01

A 2500 megawatt solid ground output Solar Power Satellite (SPS) of conventional configuration was designed and analyzed. Because the power per receiving antenna is halved, as compared with the klystron reference, twice the number of receiving antennas are needed to deliver the same total power. The solid state approach appears feasible with a slightly greater specific mass and slightly higher cost than the klystron SPS design.

Uncertainties for seismic moment tensors and applications to nuclear explosions, volcanic events, and earthquakes

NASA Astrophysics Data System (ADS)

Tape, C.; Alvizuri, C. R.; Silwal, V.; Tape, W.

2017-12-01

When considered as a point source, a seismic source can be characterized in terms of its origin time, hypocenter, moment tensor, and source time function. The seismologist's task is to estimate these parameters--and their uncertainties--from three-component ground motion recorded at irregularly spaced stations. We will focus on one portion of this problem: the estimation of the moment tensor and its uncertainties. With magnitude estimated separately, we are left with five parameters describing the normalized moment tensor. A lune of normalized eigenvalue triples can be used to visualize the two parameters (lune longitude and lune latitude) describing the source type, while the conventional strike, dip, and rake angles can be used to characterize the orientation. Slight modifications of these five parameters lead to a uniform parameterization of moment tensors--uniform in the sense that equal volumes in the coordinate domain of the parameterization correspond to equal volumes of moment tensors. For a moment tensor m that we have inferred from seismic data for an earthquake, we define P(V) to be the probability that the true moment tensor for the earthquake lies in the neighborhood of m that has fractional volume V. The average value of P(V) is then a measure of our confidence in our inference of m. The calculation of P(V) requires knowing both the probability P(w) and the fractional volume V(w) of the set of moment tensors within a given angular radius w of m. We apply this approach to several different data sets, including nuclear explosions from the Nevada Test Site, volcanic events from Uturuncu (Bolivia), and earthquakes. Several challenges remain: choosing an appropriate misfit function, handling time shifts between data and synthetic waveforms, and extending the uncertainty estimation to include more source parameters (e.g., hypocenter and source time function).

Development and Deployment of an Aerospace Recommended Practice (ARP) Compliant Measurement System for nvPM Certification Measurements of Aircraft Engines - Current Status.

NASA Astrophysics Data System (ADS)

Whitefield, P. D.; Hagen, D. E.; Lobo, P.; Miake-Lye, R. C.

2015-12-01

The Society of Automotive Engineers (SAE) Aircraft Exhaust Emissions Measurement Committee (E-31) has published an Aerospace Information Report (AIR) 6241 detailing the sampling system for the measurement of non-volatile particulate matter (nvPM) from aircraft engines (SAE 2013). The system is designed to operate in parallel with existing International Civil Aviation Organization (ICAO) Annex 16 compliant combustion gas sampling systems used for emissions certification from aircraft engines captured by conventional (Annex 16) gas sampling rakes (ICAO, 2008). The SAE E-31 committee is also working to ballot an Aerospace Recommended Practice (ARP) that will provide the methodology and system specification to measure nvPM from aircraft engines. The ARP is currently in preparation and is expected to be ready for ballot in 2015. A prototype AIR-compliant nvPM measurement system - The North American Reference System (NARS) has been built and evaluated at the MSTCOE under the joint sponsorship of the FAA, EPA and Transport Canada. It has been used to validate the performance characteristics of OEM AIR-compliant systems and is being used in engine certification type testing at OEM facilities to obtain data from a set of representative engines in the fleet. The data collected during these tests will be used by ICAO/CAEP/WG3/PMTG to develop a metric on which on the regulation for nvPM emissions will be based. This paper will review the salient features of the NARS including: (1) emissions sample transport from probe tip to the key diagnostic tools, (2) the mass and number-based diagnostic tools for nvPM mass and number concentration measurement and (3) methods employed to assess the extent of nvPM loss throughout the sampling system. This paper will conclude with a discussion of the recent results from inter-comparison studies conducted with other US - based systems that gives credence to the ARP's readiness for ballot.

Comparative study of receiver-side ghost wavefield attenuation on different marine acquisition configurations

NASA Astrophysics Data System (ADS)

Zhang, Hao; Liu, Qiancheng; Li, Hongyuan; Zhang, Yi

2018-04-01

In marine seismic exploration, the ghost energies (down-going waves), which arise from the reflection at the surface, are often treated as unwanted signals for data processing. The ghost wave fields interfere with the desired primary signals, leads to frequency notches and attenuation of low frequencies, which in turn downgrade the resolution of the recorded seismic data. There are two main categories of methods to solve the ghost or the so-called notch problem: the non-conventional acquisition configuration-based technique and a deghosting algorithm-based solution. The variable-depth streamer (VDS) acquisition solution is one of the most representative methods in the first category, which has become a popular solution for marine seismic acquisition to obtain broad data bandwidth. However, this approach is not as economic as the conventional constant depth streamer (CDS) acquisition, due to the precise control of the towing streamer. In addition, there are large quantities of conventionally-towed legacy data stored in the data library. Applying receiver deghosting to the CDS data thus becomes a more economical method. In theory, both types of data after deghosting should have the same bandwidth and S/N ratio, but in reality they are different. In this paper, we conduct a comparative study and evaluation to apply receiver deghosting to a set of real 2D marine data including both types of acquisition (CDS and VDS) corresponding to the same geology. The deghosting algorithm we employed is a self-sustained, inversion-based approach operated in the τ-p domain. This evaluation can help us to understand two questions: whether the VDS acquisition has more broadband characteristics compared to conventional CDS acquisition after deghosting, and whether we can achieve the identical or similar data quality (e.g., S/N ratio) through the proper deghosting algorithm for both types of data. The comparative results are illustrated and discussed.

Wristwatch dosimeter

DOEpatents

Wolf, Michael A.; Waechter, David A.; Umbarger, C. John

1986-01-01

The disclosure is directed to a wristwatch dosimeter utilizing a CdTe detector, a microprocessor and an audio and/or visual alarm. The dosimeter is entirely housable with a conventional digital watch case having an additional aperture enabling the detector to receive radiation.

IMPROVED SYNTHESIS OF ROOM TEMPERATURE IONIC LIQUIDS

EPA Science Inventory

Room temperature ionic liquids (RTILs), molten salts comprised of N-alkylimidazolium cations and various anions, have received significant attention due to their commercial potential in a variety of chemical applications especially as substitutes for conventional volatile organic...

Pavement marking extensions for deceleration lanes.

DOT National Transportation Integrated Search

1974-01-01

Pavement markings have definite and important functions in a proper scheme of traffic control. One such marking, the pavement edge line, has received much favorable public reaction. One of the limitations of the edge line as conventionally applied is...

A randomized control trial evaluating fluorescent ink versus dark ink tattoos for breast radiotherapy

PubMed Central

Kirby, Anna M; Lee, Steven F; Bartlett, Freddie; Titmarsh, Kumud; Donovan, Ellen; Griffin, Clare L; Gothard, Lone; Locke, Imogen; McNair, Helen A

2016-01-01

Objective: The purpose of this UK study was to evaluate interfraction reproducibility and body image score when using ultraviolet (UV) tattoos (not visible in ambient lighting) for external references during breast/chest wall radiotherapy and compare with conventional dark ink. Methods: In this non-blinded, single-centre, parallel group, randomized control trial, patients were allocated to receive either conventional dark ink or UV ink tattoos using computer-generated random blocks. Participant assignment was not masked. Systematic (∑) and random (σ) setup errors were determined using electronic portal images. Body image questionnaires were completed at pre-treatment, 1 month and 6 months to determine the impact of tattoo type on body image. The primary end point was to determine that UV tattoo random error (σsetup) was no less accurate than with conventional dark ink tattoos, i.e. <2.8 mm. Results: 46 patients were randomized to receive conventional dark or UV ink tattoos. 45 patients completed treatment (UV: n = 23, dark: n = 22). σsetup for the UV tattoo group was <2.8 mm in the u and v directions (p = 0.001 and p = 0.009, respectively). A larger proportion of patients reported improvement in body image score in the UV tattoo group compared with the dark ink group at 1 month [56% (13/23) vs 14% (3/22), respectively] and 6 months [52% (11/21) vs 38% (8/21), respectively]. Conclusion: UV tattoos were associated with interfraction setup reproducibility comparable with conventional dark ink. Patients reported a more favourable change in body image score up to 6 months following treatment. Advances in knowledge: This study is the first to evaluate UV tattoo external references in a randomized control trial. PMID:27710100

A randomized control trial evaluating fluorescent ink versus dark ink tattoos for breast radiotherapy.

PubMed

Landeg, Steven J; Kirby, Anna M; Lee, Steven F; Bartlett, Freddie; Titmarsh, Kumud; Donovan, Ellen; Griffin, Clare L; Gothard, Lone; Locke, Imogen; McNair, Helen A

2016-12-01

The purpose of this UK study was to evaluate interfraction reproducibility and body image score when using ultraviolet (UV) tattoos (not visible in ambient lighting) for external references during breast/chest wall radiotherapy and compare with conventional dark ink. In this non-blinded, single-centre, parallel group, randomized control trial, patients were allocated to receive either conventional dark ink or UV ink tattoos using computer-generated random blocks. Participant assignment was not masked. Systematic (∑) and random (σ) setup errors were determined using electronic portal images. Body image questionnaires were completed at pre-treatment, 1 month and 6 months to determine the impact of tattoo type on body image. The primary end point was to determine that UV tattoo random error (σ setup ) was no less accurate than with conventional dark ink tattoos, i.e. <2.8 mm. 46 patients were randomized to receive conventional dark or UV ink tattoos. 45 patients completed treatment (UV: n = 23, dark: n = 22). σ setup for the UV tattoo group was <2.8 mm in the u and v directions (p = 0.001 and p = 0.009, respectively). A larger proportion of patients reported improvement in body image score in the UV tattoo group compared with the dark ink group at 1 month [56% (13/23) vs 14% (3/22), respectively] and 6 months [52% (11/21) vs 38% (8/21), respectively]. UV tattoos were associated with interfraction setup reproducibility comparable with conventional dark ink. Patients reported a more favourable change in body image score up to 6 months following treatment. Advances in knowledge: This study is the first to evaluate UV tattoo external references in a randomized control trial.

Preconception folic acid use modulates estradiol and follicular responses to ovarian stimulation.

PubMed

Twigt, John M; Hammiche, Fatima; Sinclair, Kevin D; Beckers, Nicole G; Visser, Jenny A; Lindemans, Jan; de Jong, Frank H; Laven, Joop S E; Steegers-Theunissen, Régine P

2011-02-01

Folate is a methyl donor. Availability of folate affects DNA methylation profiles and thereby gene expression profiles. We investigated the effects of low-dose folic acid use (0.4 mg/d) on the ovarian response to mild and conventional ovarian stimulation in women. In a randomized trial among subfertile women, 24 and 26 subjects received conventional and mild ovarian stimulation, respectively. Blood samples were taken during the early follicular phase of the cycle prior to treatment and on the day of human chorionic gonadotropin administration for determination of serum total homocysteine, anti-Müllerian hormone (AMH), estradiol, and folate. Folic acid use was validated by questionnaire and serum folate levels. Preovulatory follicles were visualized, counted, and diameters recorded using transvaginal ultrasound. The relation between folic acid use and ovarian response was assessed using linear regression analysis. Folic acid use modified the ovarian response to ovarian stimulation treatment. The estradiol response was higher in nonfolic acid users receiving conventional treatment [β(interaction) = 0.52 (0.07-0.97); P = 0.03], and this effect was independent of serum AMH levels and the preovulatory follicle count. In the conventional treatment, the mean follicle number was also greater in nonusers compared with the users group (14.1 vs. 8.9, P = 0.03). Low-dose folic acid use attenuates follicular and endocrine responses to conventional stimulation, independent of AMH and follicle count. The nature of this observation suggests that the effect of folic acid is most prominent during early follicle development, affecting immature follicles. Deleterious effects of folate deficiency, like DNA hypomethylation and oxidative stress, can help to explain our observations.

Ultrasound-Guided Selective Versus Conventional Block of the Medial Brachial Cutaneous and the Intercostobrachial Nerves: A Randomized Clinical Trial.

PubMed

Magazzeni, Philippe; Jochum, Denis; Iohom, Gabriella; Mekler, Gérard; Albuisson, Eliane; Bouaziz, Hervé

2018-06-13

For superficial surgery of anteromedial and posteromedial surfaces of the upper arm, the medial brachial cutaneous nerve (MBCN) and the intercostobrachial nerve (ICBN) must be selectively blocked, in addition to an axillary brachial plexus block. We compared efficacy of ultrasound-guided (USG) versus conventional block of the MBCN and the ICBN. Eighty-four patients, undergoing upper limb surgery, were randomized to receive either USG (n = 42) or conventional (n = 42) block of the MBCN and the ICBN with 1% mepivacaine. Sensory block was evaluated using light-touch on the upper and lower half of the anteromedial and posteromedial surfaces of the upper arm at 5, 10, 15, 20 minutes after nerve blocks. The primary outcome was the proportion of patients who had no sensation in all 4 regions innervated by the MBCN and the ICBN at 20 minutes. Secondary outcomes were onset time of complete anesthesia, volume of local anesthetic, tourniquet tolerance, and quality of ultrasound images. In the USG group, 37 patients (88%) had no sensation at 20 minutes in any of the 4 areas tested versus 8 patients (19%) in the conventional group (P < 0.001). When complete anesthesia was obtained, it occurred within 10 minutes in more than 90% of patients, in both groups. Mean total volumes of local anesthetic used for blocking the MBCN and the ICBN were similar in the 2 groups. Ultrasound images were of good quality in only 20 (47.6%) of 42 patients. Forty-one patients (97.6%) who received USG block were comfortable with the tourniquet versus 16 patients (38.1%) in the conventional group (P < 0.001). Ultrasound guidance improved the efficacy of the MBCN and ICBN blocks. This study was registered at ClinicalTrials.gov, identifier NCT02940847.

Effects of exercise intervention in breast cancer patients: is mobile health (mHealth) with pedometer more effective than conventional program using brochure?

PubMed

Uhm, Kyeong Eun; Yoo, Ji Sung; Chung, Seung Hyun; Lee, Jong Doo; Lee, Ilkyun; Kim, Joong Il; Lee, Se Kyung; Nam, Seok Jin; Park, Yong Hyun; Lee, Ji Youl; Hwang, Ji Hye

2017-02-01

To investigate and compare the effects of mobile health (mHealth) and pedometer with conventional exercise program using a brochure on physical function and quality of life (QOL). The study was a prospective, quasi-randomized multicenter trial where 356 patients whose cancer treatment had been terminated were enrolled. All patients were instructed to perform a 12-week regimen of aerobic and resistance exercise. The mHealth group received a pedometer and a newly developed smartphone application to provide information and monitor the prescribed exercises. Those in the conventional group received an exercise brochure. Physical measurements were conducted at baseline, 6 weeks, and 12 weeks. Self-reported physical activity (international physical activity questionnaire-short form), general QOL (European Organization for Research and Treatment of Cancer Quality of Life Questionnaire Core 30), and breast cancer-specific QOL (Quality of Life Questionnaire Breast Cancer Module 23) were assessed at baseline and 12 weeks. A user satisfaction survey was assessed in the mHealth group. Basic characteristics were not different between the two groups except for age and previous radiotherapy. Physical function, physical activity, and QOL scores were significantly improved regardless of the intervention method, and changes were not significantly different between the two groups. Additionally, the mean Likert scale response for overall satisfaction with the service was 4.27/5 in the mHealth group. Overall, both the mHealth coupled with pedometer and conventional exercise education using a brochure were effective in improving physical function, physical activity, and QOL. This study provides a basis of mHealth research in breast cancer patients for progressing further developing field, although superiority of the mHealth over the conventional program was not definitely evident.

OHRQoL, masticatory performance and crestal bone loss with single-implant, magnet-retained mandibular overdentures with conventional and shortened dental arch.

PubMed

Grover, Manita; Vaidyanathan, Anand Kumar; Veeravalli, Padmanabhan Thallam

2014-05-01

The aim of this study was to assess the use of single implant-supported, magnet-retained mandibular overdentures to improve the oral health-related quality of life (OHRQoL) and masticatory performance of patients wearing conventional complete dentures. The study also aimed at comparing the OHRQoL, masticatory performance, and crestal bone loss with two different types of overdenture prosthesis. Ten completely edentulous patients with atrophic mandibular residual alveolar ridges and having difficulty coping with technically adequate mandibular dentures were selected for implant-supported overdentures (ISOD). To assess the success of the implant fixture clinically, a crossover study design was followed, and the patients were divided into two groups. Group A received ISOD with conventional complete dental arch, and group B received ISOD with a shortened dental arch for the first 3 months and vice versa for the next 3 months. The OHRQoL was measured with the OHIP-49 questionnaire, and masticatory performance was assessed with the sieve method using peanuts as test food. Peri-apical radiographs were taken to evaluate the crestal bone loss. A significant improvement was seen both subjectively and objectively when conventional complete dentures were modified to implant-supported prosthesis. When comparing the implant overdenture prosthesis, patients were more satisfied with conventional arch than with the shortened dental arch. In the first 3 months following implant placement, less bone loss was seen with the shortened dental arch overdenture (P < 0.05). Single implant-supported, magnet-retained mandibular overdentures significantly improve the OHRQoL of completely edentulous patients. © 2013 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

Evaluation of water quality functions of conventional and advanced soil-based onsite wastewater treatment systems.

PubMed

Cooper, Jennifer A; Loomis, George W; Kalen, David V; Amador, Jose A

2015-05-01

Shallow narrow drainfields are assumed to provide better wastewater renovation than conventional drainfields and are used for protection of surface and ground water. To test this assumption, we evaluated the water quality functions of two advanced onsite wastewater treatment system (OWTS) drainfields-shallow narrow (SND) and Geomat (GEO)-and a conventional pipe and stone (P&S) drainfield over 12 mo using replicated ( = 3) intact soil mesocosms. The SND and GEO mesocosms received effluent from a single-pass sand filter, whereas the P&S received septic tank effluent. Between 97.1 and 100% of 5-d biochemical oxygen demand (BOD), fecal coliform bacteria, and total phosphorus (P) were removed in all drainfield types. Total nitrogen (N) removal averaged 12.0% for P&S, 4.8% for SND, and 5.4% for GEO. A mass balance analysis accounted for 95.1% (SND), 94.1% (GEO), and 87.6% (P&S) of N inputs. When the whole treatment train (excluding the septic tank) is considered, advanced systems, including sand filter pretreatment and SND or GEO soil-based treatment, removed 99.8 to 99.9% of BOD, 100% of fecal coliform bacteria and P, and 26.0 to 27.0% of N. In contrast, the conventional system removed 99.4% of BOD and 100% of fecal coliform bacteria and P but only 12.0% of N. All drainfield types performed similarly for most water quality functions despite differences in placement within the soil profile. However, inclusion of the pretreatment step in advanced system treatment trains results in better N removal than in conventional treatment systems despite higher drainfield N removal rates in the latter. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Effects of recombinant human activated protein C on the fibrinolytic system of patients undergoing conventional or tight glycemic control.

PubMed

Polli, F; Savioli, M; Cugno, M; Taccone, P; Bellani, G; Spanu, P; Pesenti, A; Iapichino, G; Gattinoni, L

2009-01-01

Recombinant human activated protein C (rh-APC) and tight glycemic control (TGC) have been shown to reduce mortality in septic patients. Both interventions can reduce the plasma concentration and/or activity of the most powerful suppressor of fibrinolysis, plasminogen activator inhibitor-1 (PAI-1). Our aim was to evaluate the effects on the fibrinolytic system after the administration of rh-APC in septic patients undergoing conventional or TGC. Posthoc analysis of data was collected from 90 patients with severe sepsis/septic shock, randomized to either conventional or TGC groups. Independent of these treatments, patients with at least two organ dysfunctions simultaneously received rh-APC. Plasma levels of multiple biochemical markers for fibrinolysis, coagulation, and inflammation were determined every day for the 1st week and then on study days 9, 11, 13, 18, 23, and 28. Clinical data and sepsis-related organ failure assessment (SOFA) scores were also recorded. Patients who had received rh-APC exhibited significantly more impairments in fibrinolysis at baseline (PAI-1 activity 49.76 [24.61-71.82] vs 21.92 [6.47-55-83] IU/mL, P=0.03). The reductions in plasma PAI-1 activity over time associated with rh-APC treatment were different according to whether the treatment was administered to patients undergoing conventional or TGC (P=0.01). However, the most prominent reductions were in patients undergoing conventional glycemic control. Significant interactions between the two study interventions were also found for PAI-1 concentration (P<0.001), C-reactive protein (P=0.02), and interleukin-6 levels (P<0.001). Both rh-APC and TGC appear to improve fibrinolysis in septic patients. The reduction in the impairment of fibrinolysis associated with rh-APC treatment seems greater in patients undergoing conventional glycemic control than in those undergoing TGC.

The effect of a nurse led telephone supportive care programme on patients' quality of life, received information and health care contacts after oesophageal cancer surgery-A six month RCT-follow-up study.

PubMed

Malmström, Marlene; Ivarsson, Bodil; Klefsgård, Rosemarie; Persson, Kerstin; Jakobsson, Ulf; Johansson, Jan

2016-12-01

Following oesophagectomy, a major surgical procedure, it is known that patients suffer from severely reduced quality of life and have an unmet need for postoperative support. Still, there is a lack of research testing interventions aiming to enhance the patients' life situation after this surgical procedure. The aim of the study was to evaluate the effect of a nurse led telephone supportive care programme on quality of life (QOL), received information and the number of healthcare contacts compared to conventional care following oesophageal resection for cancer. The study was designed as a randomized controlled trial (RCT) aiming to test the effect of a nurse led telephone supportive care program compared to conventional care. Patient assessments were conducted at discharge, 2 weeks, 2, 4 and 6 months after discharge and comprised evaluation of QOL, received information and the number of health care contacts. Statistical testing were conducted with repeated measurements analysis of variance to test if there were differences between the groups during follow-up. The results show that the intervention group was significantly more satisfied with received information for items concerning the information they received about things to do to help yourself, written information and for the global information score. The control group scored significantly higher on the item regarding wishing to receive more information and wish to receive less information. No effect of the intervention was shown on QOL or number of health care contacts. Proactive nurse-led telephone follow-up has a significant positive impact on the patients' experience of received information. This is likely to have a positive effect on their ability to cope with a life that may include remaining side effects and adverse symptoms for a long time after surgery. Copyright © 2016 Elsevier Ltd. All rights reserved.

Noninvasive ventilation for avoidance of reintubation in patients with various cough strength.

PubMed

Duan, Jun; Han, Xiaoli; Huang, Shicong; Bai, Linfu

2016-10-07

Reintubation is associated with high mortality. Identification of methods to avoid reintubation is needed. The aim of this study was to assess whether prophylactic noninvasive ventilation (NIV) would benefit patients with various cough strengths. We prospectively enrolled 356 patients who successfully passed a spontaneous breathing trial in a respiratory intensive care unit. Before extubation, cough peak flow was measured. After extubation, attending physicians determined whether the patients would receive prophylactic NIV or conventional oxygen treatment (control group). Patients were followed up to 90 days postextubation or death, whichever came first. The median value of cough peak flow was 70 L/minute. Among the patients with cough peak flow ≤70 L/minute, 108 received NIV and 72 received conventional oxygen treatment. In this cohort, NIV reduced reintubation (9 % vs. 35 % at postextubation 72 h, p < 0.01; and 24 % vs. 49 % at postextubation 7 days, p < 0.01) and postextubation 90-day mortality (43 % vs. 61 %, p = 0.02) compared with the control group. Further, use of NIV was an independent protective factor for reintubation (OR = 0.19, p < 0.01 at 72 h postextubation; and OR = 0.33, p < 0.01 at 7 days postextubation) and for death at 90 days postextubation (OR = 0.40, p = 0.02). Among patients with cough peak flow >70 L/minute, 71 received NIV and 105 received conventional oxygen treatment. In this cohort, NIV did not reduce reintubation (6 % vs. 6 % at 72 h postextubation, p > 0.99; and 9 % vs. 9 % at 7 days postextubation, p > 0.99) or postextubation 90-day mortality (21 % vs. 15 %, p = 0.32) compared with the control group. Further, use of NIV was not associated with reintubation or postextubation 90-day mortality. In a planned extubated population, prophylactic NIV benefited patients with weak cough but possibly not in patients with strong cough.

Adjuvant use of acoustic pressure wound therapy for treatment of chronic wounds: a retrospective analysis.

PubMed

Cole, Pamela S; Quisberg, Jennifer; Melin, M Mark

2009-01-01

Small studies have indicated that the addition of acoustic pressure wound therapy (APWT) to conventional wound care may hasten healing of chronic wounds. We evaluated our early clinical experience using APWT as an adjunct to conventional wound care. The study was a retrospective chart review of consecutive patients receiving APWT in addition to conventional wound care in a hospital-based, primarily outpatient setting. Medical records of all patients treated with APWT between August 2006 and October 2007 were reviewed. Analysis included the 41 patients with 52 wounds who received APWT at least 2 times per week during the study period. Statistical comparisons were made for wound dimensions, tissue characteristics, and pain at start versus end of APWT. Thirty-eight percent of wounds (N = 20) healed completely with a mean 6.8 weeks of APWT. Median wound area and volume decreased significantly (88% [P < .0001] and 100% [P < .0001], respectively) from start to end of APWT. The proportion of wounds with greater than 75% granulation tissue increased from 26% (n = 12) to 80% (n = 41) (P < .0001), and normal periwound skin increased from 25% (n = 13) to 54% (n = 28) (P = .0001). Presence of greater than 50% fibrin slough decreased from 50% (n = 24) to 9% (n = 4) of wounds (P = .006). This early experience supplementing conventional wound care with APWT suggests it may promote healing in chronic wounds, where the ordered cellular and molecular processes leading to healing have stalled.

[Effects of virtual reality training on limb movement in children with spastic diplegia cerebral palsy].

PubMed

Ren, Kai; Gong, Xiao-Ming; Zhang, Rong; Chen, Xiu-Hui

2016-10-01

To study the effects of virtual reality (VR) training on the gross motor function of the lower limb and the fine motor function of the upper limb in children with spastic diplegia cerebral palsy. Thirty-five children with spastic diplegia cerebral palsy were randomly assigned to VR training group (n=19) and conventional training group (n=16). The conventional training group received conventional physical therapy and occupational therapy for three months. The VR training group received VR training and occupational therapy for three months. Grip and visual-motor integration subtests in Peabody Developmental Motor Scales-2 were used to evaluate the fine movement in patients before and after treatment. The D and E domains of the 88-item version of the Gross Motor Function Measure (GMFM-88), Modified Ashworth Scale (MAS), and Berg Balance Scale (BBS) were used to evaluate the gross movement in patients before and after treatment. Before treatment, there were no significant differences in grip, visual-motor integration, fine motor development quotient, scores of D and E domains of GMFM-88, MAS score, or BBS score between the two groups (P>0.05). After treatment, all the indices were significantly improved in the VR training group compared with the conventional training group (P<0.05). VR training can effectively improve the gross motor function of the lower limb and the fine motor function of the upper limb in children with spastic diplegia cerebral palsy.

Clinical and arthroscopic outcome of single bundle anterior cruciate ligament reconstruction: Comparison of remnant preservation versus conventional technique.

PubMed

Choi, Sungwook; Kim, Myung-Ku; Kwon, Yong Suk; Kang, Hyunseong

2017-10-01

The purpose of this study was to compare the clinical outcomes and second-look arthroscopic findings of remnant preservation technique with those of conventional anterior cruciate ligament (ACL) reconstruction in single bundle ACL reconstructions. One hundred sixty two consecutive patients underwent ACL reconstruction by one surgeon, with 93 patients receiving remnant preservation technique (Group A) and 69 patients receiving conventional ACL reconstruction (Group B). The mean follow-up was 15months. Clinical outcomes were assessed using Lysholm scores and the International Knee Documentation Committee form (IKDC form) evaluation. Post-operative knee stability was evaluated through manual knee laxity evaluation, pivot-shift test, and a Telos device. Differences in post-operative stability (manual knee laxity, pivot shift test and Telos device) were not significant between the groups (p=0.681, p=0.610, p=0.696). And also no significant differences were noted with respect to the IKDC form and the latest Lysholm scores. But in the second-look arthroscopic findings, synovial coverage was confirmed to be excellent in 36% (22/61) of Group A patients and 23% (7/30) of Group B patients. ACL reconstruction with both techniques was found to result in acceptable stability, clinical outcomes and second-look arthroscopic findings. With regard to synovial coverage, the remnant reservation techniques were found to be superior to conventional ACL reconstruction. Level III, retrospective comparative study. Copyright © 2017 Elsevier B.V. All rights reserved.

Distinct soil microbial diversity under long-term organic and conventional farming

PubMed Central

Hartmann, Martin; Frey, Beat; Mayer, Jochen; Mäder, Paul; Widmer, Franco

2015-01-01

Low-input agricultural systems aim at reducing the use of synthetic fertilizers and pesticides in order to improve sustainable production and ecosystem health. Despite the integral role of the soil microbiome in agricultural production, we still have a limited understanding of the complex response of microbial diversity to organic and conventional farming. Here we report on the structural response of the soil microbiome to more than two decades of different agricultural management in a long-term field experiment using a high-throughput pyrosequencing approach of bacterial and fungal ribosomal markers. Organic farming increased richness, decreased evenness, reduced dispersion and shifted the structure of the soil microbiota when compared with conventionally managed soils under exclusively mineral fertilization. This effect was largely attributed to the use and quality of organic fertilizers, as differences became smaller when conventionally managed soils under an integrated fertilization scheme were examined. The impact of the plant protection regime, characterized by moderate and targeted application of pesticides, was of subordinate importance. Systems not receiving manure harboured a dispersed and functionally versatile community characterized by presumably oligotrophic organisms adapted to nutrient-limited environments. Systems receiving organic fertilizer were characterized by specific microbial guilds known to be involved in degradation of complex organic compounds such as manure and compost. The throughput and resolution of the sequencing approach permitted to detect specific structural shifts at the level of individual microbial taxa that harbours a novel potential for managing the soil environment by means of promoting beneficial and suppressing detrimental organisms. PMID:25350160

OnlineTED.com--a novel web-based audience response system for higher education. A pilot study to evaluate user acceptance.

PubMed

Kühbeck, Felizian; Engelhardt, Stefan; Sarikas, Antonio

2014-01-01

Audience response (AR) systems are increasingly used in undergraduate medical education. However, high costs and complexity of conventional AR systems often limit their use. Here we present a novel AR system that is platform independent and does not require hardware clickers or additional software to be installed. "OnlineTED" was developed at Technische Universität München (TUM) based on Hypertext Preprocessor (PHP) with a My Structured Query Language (MySQL)-database as server- and Javascript as client-side programming languages. "OnlineTED" enables lecturers to create and manage question sets online and start polls in-class via a web-browser. Students can participate in the polls with any internet-enabled device (smartphones, tablet-PCs or laptops). A paper-based survey was conducted with undergraduate medical students and lecturers at TUM to compare "OnlineTED" with conventional AR systems using clickers. "OnlineTED" received above-average evaluation results by both students and lecturers at TUM and was seen on par or superior to conventional AR systems. The survey results indicated that up to 80% of students at TUM own an internet-enabled device (smartphone or tablet-PC) for participation in web-based AR technologies. "OnlineTED" is a novel web-based and platform-independent AR system for higher education that was well received by students and lecturers. As a non-commercial alternative to conventional AR systems it may foster interactive teaching in undergraduate education, in particular with large audiences.

Development of ProCaRS Clinical Nomograms for Biochemical Failure-free Survival Following Either Low-Dose Rate Brachytherapy or Conventionally Fractionated External Beam Radiation Therapy for Localized Prostate Cancer

PubMed Central

Warner, Andrew; Pickles, Tom; Crook, Juanita; Martin, Andre-Guy; Souhami, Luis; Catton, Charles; Lukka, Himu

2015-01-01

Purpose: Although several clinical nomograms predictive of biochemical failure-free survival (BFFS) for localized prostate cancer exist in the medical literature, making valid comparisons can be challenging due to variable definitions of biochemical failure, the disparate distribution of prognostic factors, and received treatments in patient populations. The aim of this investigation was to develop and validate clinically-based nomograms for 5-year BFFS using the ASTRO II “Phoenix” definition for two patient cohorts receiving low-dose rate (LDR) brachytherapy or conventionally fractionated external beam radiation therapy (EBRT) from a large Canadian multi-institutional database. Methods and Materials: Patients were selected from the GUROC (Genitourinary Radiation Oncologists of Canada) Prostate Cancer Risk Stratification (ProCaRS) database if they received (1) LDR brachytherapy ≥ 144 Gy (n=4208) or (2) EBRT ≥ 70 Gy  (n=822). Multivariable Cox regression analysis for BFFS was performed separately for each cohort and used to generate clinical nomograms predictive of 5-year BFFS. Nomograms were validated using calibration plots of nomogram predicted probability versus observed probability via Kaplan-Meier estimates. Results: Patients receiving LDR brachytherapy had a mean age of 64 ± 7 years, a mean baseline PSA of 6.3 ± 3.0 ng/mL, 75% had a Gleason 6, and 15% had a Gleason 7, whereas patients receiving EBRT had a mean age of 70 ± 6 years, a mean baseline PSA of 11.6 ± 10.7 ng/mL, 30% had a Gleason 6, 55% had a Gleason 7, and 14% had a Gleason 8-10. Nomograms for 5-year BFFS included age, use and duration of androgen deprivation therapy (ADT), baseline PSA, T stage, and Gleason score for LDR brachytherapy and an ADT (months), baseline PSA, Gleason score, and biological effective dose (Gy) for EBRT. Conclusions: Clinical nomograms examining 5-year BFFS were developed for patients receiving either LDR brachytherapy or conventionally fractionated EBRT and may assist clinicians in predicting an outcome. Future work should be directed at examining the role of additional prognostic factors, comorbidities, and toxicity in predicting survival outcomes. PMID:26180700

First Test of Fan Active Noise Control (ANC) Completed

NASA Technical Reports Server (NTRS)

2005-01-01

With the advent of ultrahigh-bypass engines, the space available for passive acoustic treatment is becoming more limited, whereas noise regulations are becoming more stringent. Active noise control (ANC) holds promise as a solution to this problem. It uses secondary (added) noise sources to reduce or eliminate the offending noise radiation. The first active noise control test on the low-speed fan test bed was a General Electric Company system designed to control either the exhaust or inlet fan tone. This system consists of a "ring source," an induct array of error microphones, and a control computer. Fan tone noise propagates in a duct in the form of spinning waves. These waves are detected by the microphone array, and the computer identifies their spinning structure. The computer then controls the "ring source" to generate waves that have the same spinning structure and amplitude, but 180 out of phase with the fan noise. This computer generated tone cancels the fan tone before it radiates from the duct and is heard in the far field. The "ring source" used in these tests is a cylindrical array of 16 flat-plate acoustic radiators that are driven by thin piezoceramic sheets bonded to their back surfaces. The resulting source can produce spinning waves up to mode 7 at levels high enough to cancel the fan tone. The control software is flexible enough to work on spinning mode orders from -6 to 6. In this test, the fan was configured to produce a tone of order 6. The complete modal (spinning and radial) structure of the tones was measured with two builtin sets of rotating microphone rakes. These rakes provide a measurement of the system performance independent from the control system error microphones. In addition, the far-field noise was measured with a semicircular array of 28 microphones. This test represents the first in a series of tests that demonstrate different active noise control concepts, each on a progressively more complicated modal structure. The tests are in preparation for a demonstration on a flight-type engine.

Integrating a Microwave Radiometer into Radar Hardware for Simultaneous Data Collection Between the Instruments

NASA Technical Reports Server (NTRS)

McLinden, Matthew; Piepmeier, Jeffrey

2013-01-01

The conventional method for integrating a radiometer into radar hardware is to share the RF front end between the instruments, and to have separate IF receivers that take data at separate times. Alternatively, the radar and radiometer could share the antenna through the use of a diplexer, but have completely independent receivers. This novel method shares the radar's RF electronics and digital receiver with the radiometer, while allowing for simultaneous operation of the radar and radiometer. Radars and radiometers, while often having near-identical RF receivers, generally have substantially different IF and baseband receivers. Operation of the two instruments simultaneously is difficult, since airborne radars will pulse at a rate of hundreds of microseconds. Radiometer integration time is typically 10s or 100s of milliseconds. The bandwidth of radar may be 1 to 25 MHz, while a radiometer will have an RF bandwidth of up to a GHz. As such, the conventional method of integrating radar and radiometer hardware is to share the highfrequency RF receiver, but to have separate IF subsystems and digitizers. To avoid corruption of the radiometer data, the radar is turned off during the radiometer dwell time. This method utilizes a modern radar digital receiver to allow simultaneous operation of a radiometer and radar with a shared RF front end and digital receiver. The radiometer signal is coupled out after the first down-conversion stage. From there, the radar transmit frequencies are heavily filtered, and the bands outside the transmit filter are amplified and passed to a detector diode. This diode produces a DC output proportional to the input power. For a conventional radiometer, this level would be digitized. By taking this DC output and mixing it with a system oscillator at 10 MHz, the signal can instead be digitized by a second channel on the radar digital receiver (which typically do not accept DC inputs), and can be down-converted to a DC level again digitally. This unintuitive step allows the digital receiver to sample both the radiometer and radar data at a rapid, synchronized data rate (greater than 1 MHz bandwidth). Once both signals are sampled by the same digital receiver, high-speed quality control can be performed on the radiometer data to allow it to take data simultaneously with the radar. The radiometer data can be blanked during radar transmit, or when the radar return is of a power level high enough to corrupt the radiometer data. Additionally, the receiver protection switches in the RF front end can double as radiometer calibration sources, the short (four-microsecond level) switching periods integrated over many seconds to estimate the radiometer offset. The major benefit of this innovation is that there is minimal impact on the radar performance due to the integration of the radiometer, and the radiometer performance is similarly minimally affected by the radar. As the radar and radiometer are able to operate simultaneously, there is no extended period of integration time loss for the radiometer (maximizing sensitivity), and the radar is able to maintain its full number of pulses (increasing sensitivity and decreasing measurement uncertainty).

Effectiveness of a coordinated and tailored return-to-work intervention for sickness absence beneficiaries with mental health problems.

PubMed

Martin, Marie H T; Nielsen, Maj Britt D; Madsen, Ida E H; Petersen, Signe M A; Lange, Theis; Rugulies, Reiner

2013-12-01

Sickness absence and exclusion from the labour market due to mental health problems (MHPs) is a growing concern in many countries. Knowledge about effective return-to-work (RTW) intervention models is still limited, but a multidisciplinary, coordinated and tailored approach has shown promising results in the context of musculoskeletal disorders. The purpose of this study was to assess the effectiveness of this approach as implemented among sickness absence beneficiaries with MHPs. In a quasi-randomised, controlled trial, we assessed the intervention's effect in terms of time to RTW and labour market status after 1 year. We used two different analytical strategies to compare time to RTW between participants receiving the intervention (n = 88) and those receiving conventional case management (n = 80): (1) a traditional multivariable regression analysis controlling for measured confounding, and (2) an instrumental variable (IV) analysis controlling for unmeasured confounding. The two analytical approaches provided similar results in terms of a longer time to RTW among recipients of the intervention (HR = 0.50; 95 % CI 0.34-0.75), although the estimate provided by the IV-analysis was non-significant (HR = 0.70; 95 % CI 0.23-2.12). After 1 year, more recipients of the intervention than of conventional case management were receiving sickness absence benefits (p = 0.031). The intervention delayed RTW compared to conventional case management, after accounting for measured confounding. The delayed RTW may be due to either implementation or program failure, or both. It may also reflect the complexity of retaining employees with mental health problems in the workplace.

Assessing patients' preferences for characteristics associated with homeopathic and conventional treatment of asthma: a conjoint analysis study

PubMed Central

Ratcliffe, J; Van Haselen, R; Buxton, M; Hardy, K; Colehan, J; Partridge, M

2002-01-01

Background: A study was undertaken to investigate the preferences of patients with asthma for attributes or characteristics associated with treatment for their asthma and to investigate the extent to which such preferences may differ between patient subgroups. Methods: The economic technique of conjoint analysis (CA) was used to investigate patients' strength of preference for several key attributes associated with services for the treatment of asthma. A CA questionnaire was administered to two groups of asthma outpatients aged 18 years or older, 150 receiving conventional treatment at Whipps Cross Hospital (WC) and 150 receiving homeopathic treatment at the Royal London Homoeopathic Hospital (RL). Results: An overall response rate of 47% (n=142) was achieved. Statistically significant attributes in influencing preferences for both the WC and RL respondents were (1) the extent to which the doctor gave sufficient time to listen to what the patient has to say, (2) the extent to which the treatment seemed to relieve symptoms, and (3) the travel costs of attending for an asthma consultation. The extent to which the doctor treated the patient as a whole person was also a statistically significant attribute for the RL respondents. Conclusions: This study has shown that aspects associated with the process of delivery of asthma services are important to patients in addition to treatment outcomes. The homeopathic respondents expressed stronger preferences for the doctor to treat them as a whole person than the patients receiving conventional treatment. Overall, the preferences for the attributes included in the study were similar for both groups. PMID:12037224

Virtual reality for upper extremity rehabilitation in early stroke: a pilot randomized controlled trial.

PubMed

Yin, Chan Wai; Sien, Ng Yee; Ying, Low Ai; Chung, Stephanie Fook-Chong Man; Tan May Leng, Dawn

2014-11-01

To investigate the effect of virtual reality (VR) rehabilitation on upper extremity motor performance of patients with early stroke. Pilot randomized controlled trial. Rehabilitation wards. Twenty three adults with stroke (mean age (SD) = 58.35 (13.45) years and mean time since stroke (SD) = 16.30 (7.44) days). Participants were randomly assigned to VR group (n=11) or control group (n=12). VR group received nine 30 minutes upper extremity VR therapy in standing (five weekdays in two weeks) plus conventional therapy, which included physical and occupational therapy. Control group received only conventional therapy, which was comparable to total training time received by VR group (mean training hours (SD):VR = 17.07 (2.86); control = 15.50 (2.79)). The main outcome measure was the Fugl-Meyer Assessment (FMA). Secondary outcomes included Action Research Arm Test, Motor Activity Log and Functional Independence Measure. Results were taken at baseline, post intervention and 1-month post intervention. Participants' feedback and adverse effects were recorded. All participants improved in FMA scores (mean change (SD) = 11.65 (8.56), P<.001). These effects were sustained at one month after intervention (mean (SD) change from baseline = 18.67 (13.26), P<.001). All other outcome measures showed similar patterns. There were no significant differences in improvement between both groups. Majority of the participants found VR training useful and enjoyable, with no serious adverse effects reported. Although additional VR training was not superior to conventional therapy alone, this study demonstrates the feasibility of VR training in early stroke. © The Author(s) 2014.

Systemic inflammatory response after endoscopic (TEP) vs Shouldice groin hernia repair.

PubMed

Schwab, R; Eissele, S; Brückner, U B; Gebhard, F; Becker, H P

2004-08-01

Endoscopic techniques are commonly used for many different types of surgery. It is claimed that videoendoscopic procedures have the advantage of being less traumatic and of offering higher postoperative patient comfort than conventional open techniques. The extent of tissue trauma can be evaluated on the basis of the inflammatory response observed in the wake of surgery. Available studies that have compared endoscopic and conventional techniques suggest that endoscopic cholecystectomy, laparoscopic colorectal resection, and thoracoscopic pulmonary resection have immunologic advantages over conventional approaches. The objective of this prospective study was to determine whether endoscopic hernia repair techniques are also preferable to conventional procedures and to what extent the anesthetic technique (local or general anesthesia) influences the postoperative inflammatory response. For this purpose, biochemical monitoring of cytokine activity [C-reactive protein (CRP), prostaglandin F1alpha (PGF1alpha), neopterin, interleukin-6 (IL-6)] was done prospectively in 101 patients [totally extraperitoneal approach (TEP) n=32, unilateral n=12, bilateral n=20; Shouldice n=69, local anesthesia (LA) n=23, general anesthesia (GA) n=46] before and until 3 days after surgery. The parameters IL-6 and PGF1alpha suggested that the immune trauma immediately after surgery was significantly higher in the group of patients with endoscopic hernia repair than in the group of patients who received a Shouldice repair. No significant differences were observed after the first postoperative day. A comparison between the TEP group and the patients who received conventional surgery under local anesthesia showed that the TEP approach was also associated with a higher postoperative neopterin level. Within the first 3 days after surgical intervention, bilateral endoscopic hernia repair induced no significantly higher inflammatory response than the surgical treatment of unilateral conditions. The anesthetic procedure that was used in the Shouldice operation had no significant effect on inflammatory response. Unlike other types of endoscopic surgery, the repair of groin hernias using an endoscopic technique cannot be regarded as a minimally invasive procedure that is less traumatic than conventional approaches. Instead, the conventional Shouldice procedure appears to cause the lowest inflammatory response and to be the least traumatic approach to hernia repair, especially when it is performed under local anesthesia.

For 481 biomedical open access journals, articles are not searchable in the Directory of Open Access Journals nor in conventional biomedical databases

PubMed Central

Andresen, Kristoffer; Pommergaard, Hans-Christian; Rosenberg, Jacob

2015-01-01

Background. Open access (OA) journals allows access to research papers free of charge to the reader. Traditionally, biomedical researchers use databases like MEDLINE and EMBASE to discover new advances. However, biomedical OA journals might not fulfill such databases’ criteria, hindering dissemination. The Directory of Open Access Journals (DOAJ) is a database exclusively listing OA journals. The aim of this study was to investigate DOAJ’s coverage of biomedical OA journals compared with the conventional biomedical databases. Methods. Information on all journals listed in four conventional biomedical databases (MEDLINE, PubMed Central, EMBASE and SCOPUS) and DOAJ were gathered. Journals were included if they were (1) actively publishing, (2) full OA, (3) prospectively indexed in one or more database, and (4) of biomedical subject. Impact factor and journal language were also collected. DOAJ was compared with conventional databases regarding the proportion of journals covered, along with their impact factor and publishing language. The proportion of journals with articles indexed by DOAJ was determined. Results. In total, 3,236 biomedical OA journals were included in the study. Of the included journals, 86.7% were listed in DOAJ. Combined, the conventional biomedical databases listed 75.0% of the journals; 18.7% in MEDLINE; 36.5% in PubMed Central; 51.5% in SCOPUS and 50.6% in EMBASE. Of the journals in DOAJ, 88.7% published in English and 20.6% had received impact factor for 2012 compared with 93.5% and 26.0%, respectively, for journals in the conventional biomedical databases. A subset of 51.1% and 48.5% of the journals in DOAJ had articles indexed from 2012 and 2013, respectively. Of journals exclusively listed in DOAJ, one journal had received an impact factor for 2012, and 59.6% of the journals had no content from 2013 indexed in DOAJ. Conclusions. DOAJ is the most complete registry of biomedical OA journals compared with five conventional biomedical databases. However, DOAJ only indexes articles for half of the biomedical journals listed, making it an incomplete source for biomedical research papers in general. PMID:26038727

For 481 biomedical open access journals, articles are not searchable in the Directory of Open Access Journals nor in conventional biomedical databases.

PubMed

Liljekvist, Mads Svane; Andresen, Kristoffer; Pommergaard, Hans-Christian; Rosenberg, Jacob

2015-01-01

Background. Open access (OA) journals allows access to research papers free of charge to the reader. Traditionally, biomedical researchers use databases like MEDLINE and EMBASE to discover new advances. However, biomedical OA journals might not fulfill such databases' criteria, hindering dissemination. The Directory of Open Access Journals (DOAJ) is a database exclusively listing OA journals. The aim of this study was to investigate DOAJ's coverage of biomedical OA journals compared with the conventional biomedical databases. Methods. Information on all journals listed in four conventional biomedical databases (MEDLINE, PubMed Central, EMBASE and SCOPUS) and DOAJ were gathered. Journals were included if they were (1) actively publishing, (2) full OA, (3) prospectively indexed in one or more database, and (4) of biomedical subject. Impact factor and journal language were also collected. DOAJ was compared with conventional databases regarding the proportion of journals covered, along with their impact factor and publishing language. The proportion of journals with articles indexed by DOAJ was determined. Results. In total, 3,236 biomedical OA journals were included in the study. Of the included journals, 86.7% were listed in DOAJ. Combined, the conventional biomedical databases listed 75.0% of the journals; 18.7% in MEDLINE; 36.5% in PubMed Central; 51.5% in SCOPUS and 50.6% in EMBASE. Of the journals in DOAJ, 88.7% published in English and 20.6% had received impact factor for 2012 compared with 93.5% and 26.0%, respectively, for journals in the conventional biomedical databases. A subset of 51.1% and 48.5% of the journals in DOAJ had articles indexed from 2012 and 2013, respectively. Of journals exclusively listed in DOAJ, one journal had received an impact factor for 2012, and 59.6% of the journals had no content from 2013 indexed in DOAJ. Conclusions. DOAJ is the most complete registry of biomedical OA journals compared with five conventional biomedical databases. However, DOAJ only indexes articles for half of the biomedical journals listed, making it an incomplete source for biomedical research papers in general.

Magnetic navigation system and CT roadmap-assisted percutaneous coronary intervention: a comparison to the conventional approach.

PubMed

Hao, Ruina; Zhang, Qiu; Xu, Zhuowen; Tang, Lijun; Yang, Zhijian; Cao, Kejiang; Li, Chunjian

2013-04-01

Computed tomography coronary angiography (CTCA) has been successfully integrated with the magnetic navigation system (MNS) to facilitate a roadmap-assisted percutaneous coronary intervention (PCI). The aim of this study was to compare this new approach of PCI versus conventional PCI regarding the difference of contrast usage, x-ray exposure, procedure success, and in-hospital expenses. Thirty-eight patients with stable coronary artery disease and coronary artery lesions of ≥70% diameter stenosis diagnosed by both pre-procedure CTCA and coronary angiography (CAG) were enrolled to receive the MNS and CT roadmap-assisted PCI. Another 38 patients were consecutively recruited to receive conventional PCI, matched with the MNS group by the vessel and lesion type base on American College of Cardiology/American Heart Association criteria. Regarding the process of the guidewire placement, wherein the technical difference of the two procedures exists, the median contrast usage for guidewire crossing was significantly lower in the MNS group than in the conventional group [0.0 mL (interquartile range [IQR], 0.0-3.0 mL) vs 5.0 mL (IQR, 3.1-6.8 mL); P<.001], with zero contrast usage in 25 of the 44 guidewire placements in the MNS group, but in none of the conventional group; the radiation dosage for guidewire crossing in the MNS group was also significantly lower than in the conventional group (235.8 μGym² [IQR, 134.9-455.1 μGym²] vs 364.4 μGym² [IQR, 223.4-547.2 μGym²]; P=.033). There were no significant differences between the two groups concerning the total contrast usage, total radiation dosage of the PCI, the procedural fees, or the overall in-hospital expenses. All of the enrolled vessels were successfully intervened in both groups. In PCI of simple lesions, the application of CT guidance and magnetic navigation had modest impacts on radiation dosage and contrast usage for wire crossing, but no impact on overall radiation dosage or contrast usage for the procedure. In addition, the use of CT roadmap and MNS was likely more expensive compared to PCI using conventional radiographic technique.

QPPM receiver for free-space laser communications

NASA Technical Reports Server (NTRS)

Budinger, J. M.; Mohamed, J. H.; Nagy, L. A.; Lizanich, P. J.; Mortensen, D. J.

1994-01-01

A prototype receiver developed at NASA Lewis Research Center for direct detection and demodulation of quaternary pulse position modulated (QPPM) optical carriers is described. The receiver enables dual-channel communications at 325-Megabits per second (Mbps) per channel. The optical components of the prototype receiver are briefly described. The electronic components, comprising the analog signal conditioning, slot clock recovery, matched filter and maximum likelihood data recovery circuits are described in more detail. A novel digital symbol clock recovery technique is presented as an alternative to conventional analog methods. Simulated link degradations including noise and pointing-error induced amplitude variations are applied. The bit-error-rate performance of the electronic portion of the prototype receiver under varying optical signal-to-noise power ratios is found to be within 1.5-dB of theory. Implementation of the receiver as a hybrid of analog and digital application specific integrated circuits is planned.

Wrist-watch dosimeter

DOEpatents

Wolf, M.A.; Waechter, D.A.; Umbarger, C.J.

1982-04-16

The disclosure is directed to a wristwatch dosimeter utilizing a CdTe detector, a microprocessor and an audio and/or visual alarm. The dosimeter is entirely housable within a conventional digital watch case having an additional aperture enabling the detector to receive radiation.

Wristwatch dosimeter

DOEpatents

Wolf, M.A.; Waechter, D.A.; Umbarger, C.J.

1986-08-26

The disclosure is directed to a wristwatch dosimeter utilizing a CdTe detector, a microprocessor and an audio and/or visual alarm. The dosimeter is entirely housable with a conventional digital watch case having an additional aperture enabling the detector to receive radiation. 10 figs.

Respiratory Source Control Using Surgical Masks With Nanofiber Media

PubMed Central

Skaria, Shaji D.; Smaldone, Gerald C.

2014-01-01

Background: Potentially infected individuals (‘source’) are sometimes encouraged to use face masks to reduce exposure of their infectious aerosols to others (‘receiver’). To improve compliance with Respiratory Source Control via face mask and therefore reduce receiver exposure, a mask should be comfortable and effective. We tested a novel face mask designed to improve breathability and filtration using nanofiber filtration. Methods: Using radiolabeled test aerosols and a calibrated exposure chamber simulating source to receiver interaction, facepiece function was measured with a life-like ventilated manikin model. Measurements included mask airflow resistance (pressure difference during breathing), filtration, (mask capture of exhaled radiolabeled test aerosols), and exposure (the transfer of ‘infectious’ aerosols from the ‘source’ to a ‘receiver’). Polydisperse aerosols were measured at the source with a mass median aerodynamic diameter of 0.95 µm. Approximately 90% of the particles were <2.0 µm. Tested facepieces included nanofiber prototype surgical masks, conventional surgical masks, and for comparison, an N95-class filtering facepiece respirator (commonly known as an ‘N95 respirator’). Airflow through and around conventional surgical face mask and nanofiber prototype face mask was visualized using Schlieren optical imaging. Results: Airflow resistance [ΔP, cmH2O] across sealed surgical masks (means: 0.1865 and 0.1791 cmH2O) approached that of the N95 (mean: 0.2664 cmH2O). The airflow resistance across the nanofiber face mask whether sealed or not sealed (0.0504 and 0.0311 cmH2O) was significantly reduced in comparison. In addition, ‘infected’ source airflow filtration and receiver exposure levels for nanofiber face masks placed on the source were comparable to that achieved with N95 placed on the source; 98.98% versus 82.68% and 0.0194 versus 0.0557, respectively. Compared to deflection within and around the conventional face masks, Schlieren optical imaging demonstrated enhanced airflow through the nanofiber mask. Conclusions: Substituting nanofiber for conventional filter media significantly reduced face mask airflow resistance directing more airflow through the face mask resulting in enhanced filtration. Respiratory source control efficacy similar to that achieved through the use of an N95 respirator worn by the source and decreased airflow resistance using nanofiber masks may improve compliance and reduce receiver exposure. PMID:24737728

High-dose octreotide acetate for management of gastroenteropancreatic neuroendocrine tumors.

PubMed

Chadha, Manpreet K; Lombardo, Jeffrey; Mashtare, Terry; Wilding, Gregory E; Litwin, Alan; Raczyk, Cheryl; Gibbs, John F; Kuvshinoff, Boris; Javle, Milind M; Iyer, Renuka V

2009-10-01

Long-acting sandostatin (S-LAR; octreotide acetate) is well tolerated and effective for symptom control and possibly disease control in gastroenteropancreatic neuroendocrine tumors (GEP-NETs). We undertook a retrospective analysis to study the efficacy and tolerability of higher doses (more than 20-30 mg/month) of S-LAR in GEP-NETs. With IRB approval, charts of all patients with GEP-NET who received S-LAR between June 2002 to September 2007 at Roswell Park Cancer Institute were reviewed and their data analyzed. Fifty-four patients with GEP-NET received S-LAR; thirty required dose escalation. Patients received a median of 5 doses of S-LAR at conventional dose followed by up-titration of the dose for symptom control (20) and radiological progression (17). Median high dose of S-LAR was 40 mg (range: 40-90 mg) with a median of 8.5 high doses received. No treatment related toxicities were seen. The estimated 1-year survival for patients on conventional dose alone was 0.77 (95% CI of 0.50 to 0.91) and those on high-dose was 0.88 (95% CI of 0.68 to 0.96) (p=0.4777) while median time to any other intervention was 2.9 months versus 17.7 months (p=0.12). Dose escalation of S-LAR is well tolerated and may provide longer disease control.

'Boomerang' technique: an improved method for conformal treatment of locally advanced nasopharyngeal cancer.

PubMed

Corry, June; Hornby, Colin; Fisher, Richard; D'Costa, Ieta; Porceddu, Sandro; Rischin, Danny; Peters, Lester J

2004-06-01

The primary aim of the present study was to assess radiation dosimetry and subsequent clinical outcomes in patients with locally advanced nasopharyngeal cancer using a novel radiation technique termed the 'Boomerang'. Dosimetric comparisons were made with both conventional and intensity modulated radiation therapy (IMRT) techniques. This is a study of 22 patients treated with this technique from June 1995 to October 1998. The technique used entailed delivery of 36 Gy in 18 fractions via parallel opposed fields, then 24 Gy in 12 fractions via asymmetric rotating arc fields for a total of 60 Gy in 30 fractions. Patients also received induction and concurrent chemotherapy. The radiation dosimetry was excellent. Dose-volume histograms showed that with the arc fields, 90% of the planning target volume received 94% of the prescribed dose. Relative to other conventional radiation therapy off-cord techniques, the Boomerang technique results in a 27% greater proportion of the prescribed dose being received by 90% of the planning target volume. This translates into an overall 10% greater dose received for the same prescribed dose. At 3 years, the actuarial loco-regional control rate, the failure-free survival rate and the overall survival rate were 91, 75 and 91%, respectively. At 5 years, the actuarial loco-regional control rate, the failure-free survival rate and the overall survival rate were 74, 62 and 71%, respectively. The Boomerang technique provided excellent radiation dosimetry with correspondingly good loco-regional control rates (in conjunction with chemotherapy) and very acceptable acute and late toxicity profiles. Because treatment can be delivered with conventional standard treatment planning and delivery systems, it is a validated treatment option for centres that do not have the capability or capacity for IMRT. A derivative of the Boomerang technique, excluding the parallel opposed component, is now our standard for patients with locally advanced nasopharyngeal cancer when IMRT is not available.

Evaluation of a Self-Management Program for Gastroesophageal Reflux Disease in China

PubMed Central

Xu, Wenhong; Sun, Changxian; Lin, Lin; Wang, Meifeng; Zhang, Hongjie; Song, Yulei

2016-01-01

Gastroesophageal reflux disease is a chronic disease with a high incidence worldwide. The various symptoms have substantial impact on the quality of life of affected individuals. A long-term self-management program can increase the ability of patients to make behavioral changes, and health outcomes can improve as a consequence. This study's aim was to evaluate the effectiveness of a self-management program for gastroesophageal reflux disease. A total of 115 patients with gastroesophageal reflux disease were allocated to the experimental group and the control group. The former received self-management intervention along with conventional drug therapy, whereas the latter received standard outpatient care and conventional drug therapy. After the clinical trial, the control group also received the same self-management intervention. The levels of self-management behaviors, self-efficacy, gastroesophageal reflux disease symptoms, and psychological condition were compared. Those in the experimental group demonstrated significantly higher self-efficacy for managing their illness, showed positive changes in self-management behaviors, and had comparatively better remission of symptoms and improvement in psychological distress. The program helped patients with gastroesophageal reflux disease self-manage their illness as possible. PMID:27684637

Psoralen-ultraviolet A treatment with Psoralen-ultraviolet B therapy in the treatment of psoriasis.

PubMed

Ahmed Asim, Sadaf; Ahmed, Sitwat; Us-Sehar, Najam

2013-05-01

To compare the conventional psoralen-ultraviolet A treatment with psoralen-ultraviolet B therapy in the treatment of psoriasis. We studied 50 patients of plaque type psoriasis who were selected to receive either conventional psoralen-ultraviolet A or psoralen-ultraviolet B treatment. There was no significant difference between the two treatment groups in the number of patients whose skin cleared of psoriasis or the number of exposures required for clearance. Profile of side effects and disease status was also similar after three months of follow up. Psoralen-ultraviolet B treatment is as effective as conventional psoralen-ultraviolet A in the treatment of psoriasis. Further long term studies are needed to assess the safety of psoralen-ultraviolet B.

Ultra-compact coherent receiver with serial interface for pluggable transceiver.

PubMed

Itoh, Toshihiro; Nakajima, Fumito; Ohno, Tetsuichiro; Yamanaka, Shogo; Soma, Shunichi; Saida, Takashi; Nosaka, Hideyuki; Murata, Koichi

2014-09-22

An ultra-compact integrated coherent receiver with a volume of 1.3 cc using a quad-channel transimpedance amplifier (TIA)-IC chip with a serial peripheral interface (SPI) is demonstrated for the first time. The TIA with the SPI and photodiode (PD) bias circuits, a miniature dual polarization optical hybrid, an octal-PD and small optical coupling system enabled the realization of the compact receiver. Measured transmission performance with 32 Gbaud dual-polarization quadrature phase shift keying signal is equivalent to that of the conventional multi-source agreement-based integrated coherent receiver with dual channel TIA-ICs. By comparing the bit-error rate (BER) performance with that under continuous SPI access, we also confirmed that there is no BER degradation caused by SPI interface access. Such an ultra-compact receiver is promising for realizing a new generation of pluggable transceivers.

Ocular changes with oral and transepidermal diethylcarbamazine therapy of onchocerciasis.

PubMed Central

Taylor, H R; Greene, B M

1981-01-01

Twenty men with moderate infection of Onchocerca volvulus were studied in a double-masked, controlled clinical trial to compare the safety and efficacy of oral diethylcarbamazine (DEC) with topical DEC lotion. Visual acuity and colour vision did not alter during the 6 months of observation, although 2 patients receiving DEC lotion and 3 patients receiving oral DEC developed either visual field constriction or optic atrophy. Fluffy corneal opacities were common in both groups. Intraocular microfilariae also appeared in both groups but to a greater extent in those receiving DEC lotion. New chorioretinal changes developed in 4 men receiving lotion and in only 1 receiving tablets. It is concluded that DEC lotion offers no advantage over tablets in the treatment of ocular onchocerciasis and in fact may be associated with more ocular complications than the conventional oral treatment. Images PMID:7020746

Phase I study of replication-competent adenovirus-mediated double-suicide gene therapy in combination with conventional-dose three-dimensional conformal radiation therapy for the treatment of newly diagnosed, intermediate- to high-risk prostate cancer.

PubMed

Freytag, Svend O; Stricker, Hans; Pegg, Jan; Paielli, Dell; Pradhan, Deepak G; Peabody, James; DePeralta-Venturina, Mariza; Xia, Xueqing; Brown, Steve; Lu, Mei; Kim, Jae Ho

2003-11-01

The primary study objective was to determine the safety of intraprostatic administration of a replication-competent, oncolytic adenovirus containing a cytosine deaminase (CD)/herpes simplex virus thymidine kinase (HSV-1 TK) fusion gene concomitant with increasing durations of 5-fluorocytosine and valganciclovir prodrug therapy and conventional-dose three-dimensional conformal radiation therapy (3D-CRT) in patients with newly diagnosed, intermediate- to high-risk prostate cancer. Secondary objectives were to determine the persistence of therapeutic transgene expression in the prostate and to examine early posttreatment response. Fifteen patients in five cohorts received a single intraprostatic injection of 10(12) viral particles of the replication-competent Ad5-CD/TKrep adenovirus on day 1. Two days later, patients were administered 5-fluorocytosine and valganciclovir prodrug therapy for 1 (cohorts 1-3), 2 (cohort 4), or 3 (cohort 5) weeks along with 70-74 Gy 3D-CRT. Sextant needle biopsy of the prostate was obtained at 2 (cohort 1), 3 (cohort 2), and 4 (cohort 3) weeks for determination of the persistence of transgene expression. There were no dose-limiting toxicities and no significant treatment-related adverse events. Ninety-four percent of the adverse events observed were mild to moderate and self-limiting. Acute urinary and gastrointestinal toxicities were similar to those expected for conventional-dose 3D-CRT. Therapeutic transgene expression was found to persist in the prostate for up to 3 weeks after the adenovirus injection. As expected for patients receiving definitive radiation therapy, all patients experienced significant declines in prostate-specific antigen (PSA). The mean PSA half-life in patients administered more than 1 week of prodrug therapy was significantly shorter than that of patients receiving prodrugs for only 1 week (0.6 versus 2.0 months; P < 0.02) and markedly shorter than that reported previously for patients treated with conventional-dose 3D-CRT alone (2.4 months). With a median follow-up of only 9 months, 5 of 10 (50%) patients not treated with androgen-deprivation therapy achieved a serum PSA < or = 0.5 ng/ml. The results demonstrate that replication-competent adenovirus-mediated double-suicide gene therapy can be combined safely with conventional-dose 3D-CRT in patients with intermediate- to high-risk prostate cancer. The shorter than expected PSA half-life in patients receiving more than 1 week of prodrug therapy may suggest a possible interaction between the oncolytic adenovirus and/or double-suicide gene therapies and radiation therapy.

Changing attitudes toward sustainable transportation: The impact of meta-arguments on persuasion

DOT National Transportation Integrated Search

2017-08-01

An experiment tested the effects of both communications about the functions of an attitude and communications about the functions of an attitude object on persuasion. Participants received a conventional message about the benefits of public transport...